WorldWideScience

Sample records for combustion engine phenomena

  1. Fundamental phenomena affecting low temperature combustion and HCCI engines, high load limits and strategies for extending these limits

    KAUST Repository

    Saxena, Samveg

    2013-10-01

    Low temperature combustion (LTC) engines are an emerging engine technology that offers an alternative to spark-ignited and diesel engines. One type of LTC engine, the homogeneous charge compression ignition (HCCI) engine, uses a well-mixed fuel–air charge like spark-ignited engines and relies on compression ignition like diesel engines. Similar to diesel engines, the use of high compression ratios and removal of the throttling valve in HCCI allow for high efficiency operation, thereby allowing lower CO2 emissions per unit of work delivered by the engine. The use of a highly diluted well-mixed fuel–air charge allows for low emissions of nitrogen oxides, soot and particulate matters, and the use of oxidation catalysts can allow low emissions of unburned hydrocarbons and carbon monoxide. As a result, HCCI offers the ability to achieve high efficiencies comparable with diesel while also allowing clean emissions while using relatively inexpensive aftertreatment technologies. HCCI is not, however, without its challenges. Traditionally, two important problems prohibiting market penetration of HCCI are 1) inability to achieve high load, and 2) difficulty in controlling combustion timing. Recent research has significantly mitigated these challenges, and thus HCCI has a promising future for automotive and power generation applications. This article begins by providing a comprehensive review of the physical phenomena governing HCCI operation, with particular emphasis on high load conditions. Emissions characteristics are then discussed, with suggestions on how to inexpensively enable low emissions of all regulated emissions. The operating limits that govern the high load conditions are discussed in detail, and finally a review of recent research which expands the high load limits of HCCI is discussed. Although this article focuses on the fundamental phenomena governing HCCI operation, it is also useful for understanding the fundamental phenomena in reactivity controlled

  2. Laser diagnostics of combustion phenomena related to engines/gas turbines. Technical report

    Energy Technology Data Exchange (ETDEWEB)

    Alden, Marcus [Lund Inst. of Technology (Sweden). Dept. of Combustion

    2000-05-01

    The following project has been a one year project bridging the time between the NUTEK program in 'Motorrelaterad foerbraenning' and the new STEM program in 'Energisystem i vaegfordon. The activities has included three Ph. D students and the project has been directed towards two main areas. The first area is the development and application of a new laser diagnostic technique based on laser-induced fluorescence from atomic species for measurements of two-dimensional temperatures in combustion systems. The technique has shown to have distinct advantages compared to more commonly used laser techniques and it has been applied both in engines (VOLVO PV) as well as in gas turbines (VOLVO Aero Corp.) A major advantage is the potential, recently investigated, to make measurements in sooty environments. The second area is in the area of development and application of a technique for measurements of two-dimensional soot volume fractions and particle sizes. The technique is called Laser-induced Incandescence, LII, and here a laser beam is heating the particle considerably above the flame temperature and by detecting the increased blackbody radiation, the parameters above can be inferred. During the year most work has been to develop the technique, but distinct applications in burners, engines and model fires are planned.

  3. Experimental investigation of the fluid dynamic efficiency of a high performance multi-valve internal combustion engine during the intake phase: Influence of valve-valve interference phenomena

    Directory of Open Access Journals (Sweden)

    Algieri Angelo

    2013-01-01

    Full Text Available The purpose of the present work is the analysis of the fluid dynamic behavior of a high performance internal combustion engine during the intake phase. In particular, a four-valve spark-ignition engine has been characterized at the steady flow rig. Dimensionless discharge coefficients have been used to define the global fluid dynamic efficiency of the intake system, while the Laser Doppler Anemometry (LDA technique has been employed to evaluate the mean flow in the valve curtain area and to characterise the interference phenomena between the two intake valves. The investigation has shown the significant influence of the valve lift on the volumetric efficiency of the intake apparatus. Moreover, the experimental analysis has highlighted that the valve-valve interference phenomena have a relevant impact on the head breathability, on the flow development within the combustion chamber and on the velocity standard deviations.

  4. 8th International symposium on transport phenomena in combustion

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The 8th International Symposium on Transport Phenomena in Combustion will be held in San Francisco, California, U.S.A., July 16-20, 1995, under the auspices of the Pacific Center of Thermal-Fluids Engineering. The purpose of the Symposium is to provide a forum for researchers and practitioners from around the world to present new developments and discuss the state of the art and future directions and priorities in the areas of transport phenomena in combustion. The Symposium is the eighth in a series; previous venues were Honolulu 1985, Tokyo 1987, Taipei 1988, Sydney 1991, Beijing 1992, Seoul 1993 and Acapulco 1994, with emphasis on various aspects of transport phenomena. The current Symposium theme is combustion. The Symposium has assembled a balanced program with topics ranging from fundamental research to contemporary applications of combustion theory. Invited keynote lecturers will provide extensive reviews of topics of great interest in combustion. Colloquia will stress recent advances and innovations in fire spread and suppression, and in low NO{sub x} burners, furnaces, boilers, internal combustion engines, and other practical combustion systems. Finally, numerous papers will contribute to the fundamental understanding of complex processes in combustion. This document contains abstracts of papers to be presented at the Symposium.

  5. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Helmich, M.J.; Hoagland, M.C.; Hubbard, R.L.; Schaub, F.S.

    1981-12-22

    A method of combusting natural gas fuel in a two cycle, turbocharged internal combustion engine substantially reduces the production of nitrogen-oxygen emissions. An improved turbocharger design provides increased air charging pressure, produces a controlled lean air/fuel mixture and lowers peak combustion temperatures. A jet cell ignition device ensures uniform, reliable ignition of the lean air/fuel mixture under all operating conditions and the lean air/fuel mixture in turn encourages complete fuel combustion and provides excellent combustion characteristics with methane, ethane and heavier paraffinic hydrocarbon fuels. These structural modifications and adjustment of other operating parameters combine to reduce nitric oxide (NO) and nitrogen dioxide (NO/sub 2/) emissions by as much as 75% while effecting only a negligible increase in fuel consumption.

  6. Internal combustion piston engines

    Energy Technology Data Exchange (ETDEWEB)

    Segaser, C.L.

    1977-07-01

    Current worldwide production of internal combustion piston engines includes many diversified types of designs and a very broad range of sizes. Engine sizes range from a few horsepower in small mobile units to over 40,000 brake horsepower in large stationary and marine units. The key characteristics of internal combustion piston engines considered appropriate for use as prime movers in Integrated Community Energy Systems (ICES) are evaluated. The categories of engines considered include spark-ignition gas engines, compression-ignition oil (diesel) engines, and dual-fuel engines. The engines are evaluated with respect to full-load and part-load performance characteristics, reliability, environmental concerns, estimated 1976 cost data, and current and future status of development. The largest internal combustion piston engines manufactured in the United States range up to 13,540 rated brake horsepower. Future development efforts are anticipated to result in a 20 to 25% increase in brake horsepower without increase in or loss of weight, economy, reliability, or life expectancy, predicated on a simple extension of current development trends.

  7. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Williams, G.J.

    1986-06-03

    A variable power internal combustion engine is described which consists of: a separate air compressor for receiving and compressing a flow of air to a given pressure, the compressor having an inlet valve introducing a flow of air into the compressor and an outlet valve for exhausting compressed air out of the compressor into a compressed air storage means, at least one expander having a cylinder, a cylinder head closing an end of the cylinder, a piston reciprocally mounted in the cylinder for movement away from the cylinder head in a power stroke from an initial position defining a combustion chamber within the cylinder between the cylinder head and the piston, the compressed air storage means receiving the pressurized flow of air from the compressor and being of a volume adequate to provide compressed air in the combustion chamber essentially at the given pressure essentially over the power output of the engine, means for introducing an amount of combustible fuel in the compressed charge to be present with compressed air in the combustion chamber and providing combustion of the amount of fuel in the cylinder with the inlet and exhaust valves closed, cam shaft means in contact with the piston for absorbing and storing the energy of the power stroke of the piston and controlling movement of the piston within the cylinder during the exhaust stroke; the means for varying the volume of the combustion chamber being controlled in accordance with power requirements to provide variable power output and improved efficiency of the engine at power outputs reduced relative to a given design power output of the engine by providing a variable expansion ratio of a minimum of at least about 30 to 1 at the given design power output and higher with reduced power output.

  8. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Laskaris, M.A.; Broitman, K.; Natale, S.E.

    1991-08-27

    This patent describes improvement in a two-stroke internal combustion engine adapted to run on a diesel or a kerosene type of fuel, and including a piston connected to the crankshaft of the engine to move within a cylinder through a first stroke from a top dead center position to a bottom dead center position and through a second stroke from the bottom dead center position back to the top dead center position. The improvement comprises: means providing a cylinder head at the top end of the engine cylinder in the shape of an open bowl having a generally cup-shaped configuration including a sidewall portion, a spark plug positioned centrally within the bowl at the top end of the cylinder, and means for injecting fuel into the top end of the engine cylinder at a location between the spark plug and the sidewall portion, the fuel injecting means including an injection nozzle having a plurality of nozzle openings therein, the nozzle openings being constructed and arranged to discharge a plurality of plume-like sprays into the top end of the cylinder at a location within the bowl, two of the sprays being directed from the nozzle to diverge and pass along opposite sides of the spark plug, and additional sprays being directed from the nozzle against the sidewall portion or the cylinder head to be deflected therefrom back toward the piston and the spark plug to thereby form a cloud of fuel over the spark plug for good ignition.

  9. Supercritical droplet combustion and related transport phenomena

    Science.gov (United States)

    Yang, Vigor; Hsieh, K. C.; Shuen, J. S.

    1993-01-01

    An overview of recent advances in theoretical analyses of supercritical droplet vaporization and combustion is conducted. Both hydrocarbon and cryogenic liquid droplets over a wide range of thermodynamic states are considered. Various important high-pressure effects on droplet behavior, such as thermodynamic non-ideality, transport anomaly, and property variation, are reviewed. Results indicate that the ambient gas pressure exerts significant control of droplet gasification and burning processes through its influence on fluid transport, gas-liquid interfacial thermodynamics, and chemical reactions. The droplet gasification rate increases progressively with pressure. However, the data for the overall burnout time exhibit a considerable change in the combustion mechanism at the criticl pressure, mainly as a result of reduced mass diffusivity and latent heat of vaporization with increased pressure. The influence of droplet size on the burning characteristics is also noted.

  10. Rotary internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Witkowski, J.

    1989-12-05

    This patent describes an internal combustion engine assembly. It includes: a central rotor means formed with at least one peripheral fuel cavity. The cavity having a first surface defining a thrust surface and a second surface defining a contoured surface; a housing means enclosing the rotor and having an internal wall encircling the rotor. The internal wall being intercepted by at least two recesses defining cylinder means. The housing means and the rotor means being relatively rotatable; piston means individual to each the cylinder means and reciprocable therein; each piton means having a working face complementary to aid contoured surface; and power means for urging the working face into intimate areal contact with the contoured surface to create a first seal means. The housing means having at lest one fuel inlet port, at least one fuel ignition means and at least one exhaust port whereby during the course of a revolution of the rotor means relative to the housing means, the first seal means, the power means, the respective ports, the ignition means and the fuel cavity cooperate to develop fuel compression, fuel ignition and exhaust functions.

  11. Temperature Estimation in the Combustion Chamber of an Internal Combustion Engine

    OpenAIRE

    2012-01-01

    The mathematical model of heat transfer phenomena is considered at the combustion chamber wall in an internal combustion (IC) engine. The mathematical model of proposed phenomena is established with respect to the crank angle. An inverse heat conduction problem is derived at the cylinder wall, and this problem is investigated numerically using Alifanov's regularization method. This problem studied as an optimization problem in which a squared residual functional is minimized with the conjugat...

  12. Backfire prediction in a manifold injection hydrogen internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Xing-hua; Liu, Fu-shui; Zhou, Lei; Sun, Bai-gang [School of Mechanical and Vehicular Engineering, Beijing Institute of Technology, Beijing 100081 (China); Schock, Harold J. [Engine Research Laboratory, Michigan State University, East Lansing, MI (United States)

    2008-07-15

    Hydrogen internal combustion engine (H2ICE) easily occur inlet manifold backfire and other abnormal combustion phenomena because of the low ignition energy, wide flammability range and rapid combustion speed of hydrogen. In this paper, the effect of injection timing on mixture formation in a manifold injection H2ICE was studied in various engine speed and equivalence ratio by CFD simulation. It was concluded that H2ICE of manifold injection have an limited injection end timing in order to prevent backfire in the inlet manifold. Finally, the limit of injection end timing of the H2ICE was proposed and validated by engine experiment. (author)

  13. Combustion science and engineering

    CERN Document Server

    Annamalai, Kalyan

    2006-01-01

    Introduction and Review of Thermodynamics Introduction Combustion Terminology Matter and Its Properties Microscopic Overview of Thermodynamics Conservation of Mass and Energy and the First Law of Thermodynamics The Second Law of Thermodynamics Summary Stoichiometry and Thermochemistry of Reacting Systems Introduction Overall Reactions Gas Analyses Global Conservation Equations for Reacting Systems Thermochemistry Summary Appendix Reaction Direction and Equilibrium Introduction Reaction Direction and Chemical Equilibrium Chemical Equilibrium Relations Vant Hoff Equation Adi

  14. Staged combustion with piston engine and turbine engine supercharger

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, Larry E [Los Gatos, CA; Anderson, Brian L [Lodi, CA; O' Brien, Kevin C [San Ramon, CA

    2011-11-01

    A combustion engine method and system provides increased fuel efficiency and reduces polluting exhaust emissions by burning fuel in a two-stage combustion system. Fuel is combusted in a piston engine in a first stage producing piston engine exhaust gases. Fuel contained in the piston engine exhaust gases is combusted in a second stage turbine engine. Turbine engine exhaust gases are used to supercharge the piston engine.

  15. Free Energy and Internal Combustion Engine Cycles

    CERN Document Server

    Harris, William D

    2012-01-01

    The performance of one type (Carnot) of Internal Combustion Engine (ICE) cycle is analyzed within the framework of thermodynamic free energies. ICE performance is different from that of an External Combustion Engine (ECE) which is dictated by Carnot's rule.

  16. ABB Combustion Engineering nuclear technology

    Energy Technology Data Exchange (ETDEWEB)

    Matzie, R.A.

    1994-12-31

    The activities of ABB Combustion Engineering in the design and construction of nuclear systems and components are briefly reviewed. ABB Construction Engineering continues to improve the design and design process for nuclear generating stations. Potential improvements are evaluated to meet new requirements both of the public and the regulator, so that the designs meet the highest standards worldwide. Advancements necessary to meet market needs and to ensure the highest level of performance in the future will be made.

  17. Characterising Combustion in Diesel Engines: using parameterised finite stage cylinder process models

    NARCIS (Netherlands)

    Ding, Y.

    2011-01-01

    Characterising combustion of diesel engines is not only necessary when researching the instantaneous combustion phenomena but also when investigating the change of the combustion process under variable engine operating conditions. An effective way to achieve this goal is to parameterize the

  18. Hydrogen Internal Combustion Stirling Engine

    Science.gov (United States)

    Takahashi, Sanyo; Morita, Hiroyuki; Kurata, Osamu; Yamashita, Iwao

    The hydrogen combustion Stirling engine utilizes internal combustion of a stoichiometric H2 and O2 mixture injected into the working gas as thermal input, and the cyclic operation is completed with the removal of water from the engine after condensation at the cooler. In the prototype engine, a catalytic combustor is substituted for the conventional heater, and the H2-O2 mixture is injected at a constant flow rate from the boundary between the regenerator and the cooler. The engine internal heating characteristics were compared to those on external heating to clarify the internal heating effect on the engine performance. The internal heating performance showed almost the same characteristics as those of external heating, except for the increase of expansion work due to the direct thermal input. The increase of expansion work improved the engine performance, particularly in the region of high engine speed. Furthermore, it was found that the steady injection method was able to suppress the mixture strength to a relatively low level.

  19. Basic transport phenomena in materials engineering

    CERN Document Server

    Iguchi, Manabu

    2014-01-01

    This book presents the basic theory and experimental techniques of transport phenomena in materials processing operations. Such fundamental knowledge is highly useful for researchers and engineers in the field to improve the efficiency of conventional processes or develop novel technology. Divided into four parts, the book comprises 11 chapters describing the principles of momentum transfer, heat transfer, and mass transfer in single phase and multiphase systems. Each chapter includes examples with solutions and exercises to facilitate students’ learning. Diagnostic problems are also provided at the end of each part to assess students’ comprehension of the material.  The book is aimed primarily at students in materials science and engineering. However, it can also serve as a useful reference text in chemical engineering as well as an introductory transport phenomena text in mechanical engineering. In addition, researchers and engineers engaged in materials processing operations will find the material use...

  20. Fundamental studies of fuel chemistry as related to internal combustion engine phenomena. Technical progress report, July 1, 1988--June 30, 1989

    Energy Technology Data Exchange (ETDEWEB)

    Dryer, F.L.; Brezinsky, K.

    1989-07-01

    The present research effort was initiated with the intent of providing substantially improved insights (through homogeneous gas phase kinetic studies at different constant pressures) to the fuel chemistry issues important to autoignition in engines. The conditions of the proposed experiments were chosen to represent those similar to the engine parameters under knocking conditions: temperatures in the range of 700--1,100K, pressures from one to approximately 20 atmospheres and stoichiometries around one. A major part of the proposed research has been to design and construct a variable pressure flow reactor facility in which a range of reaction pressures, and in fact, lower reaction temperatures could be accessed. The reactor facility design and construction are nearly complete, and initial testing has begun to compare the overall experimental operating characteristics of the reactor with the design parameters. Experiments on Isobutene/oxygen mixtures have also been conducted in the existing atmospheric pressure flow reactor at about 1,150 K and in an equivalence ratio range of pyrolysis with about 100 ppm oxygen background to 0.42. A detailed kinetic model has been developed to interpret the pyrolysis and oxidation characteristics. 89 refs.

  1. Temperature Estimation in the Combustion Chamber of an Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Gholam Reza Safakish

    2012-01-01

    Full Text Available The mathematical model of heat transfer phenomena is considered at the combustion chamber wall in an internal combustion (IC engine. The mathematical model of proposed phenomena is established with respect to the crank angle. An inverse heat conduction problem is derived at the cylinder wall, and this problem is investigated numerically using Alifanov's regularization method. This problem studied as an optimization problem in which a squared residual functional is minimized with the conjugate gradient method. To show the ability of the proposed method, some test problems are considered.

  2. Combustion characteristics of turbo charged DISI-engines

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmeyer, Henrik

    2012-07-01

    In spite of progress in the development of alternative powertrain systems and energy sources, the internal combustion and all its derivates still are and will be the main powertrain for automobiles. In SI-engines, several approaches compete with each other like the controlled auto ignition (CAI or HCCI), throttle-free load control using variable valvetrains, stratified mixture formation with lean engine operation or highly turbo charged downsizing concepts all combined with gasoline direct injection. The presented work makes a contribution for a deeper understanding of the combustion process of a turbo charged direct injection engine operating with external EGR as well as lean stratified mixture. Using detailed test bench investigations and introducing a new optical measurement tool, the combustion process is described in detail focusing on the occurrence of non-premixed combustion phenomena. The influence of engine parameters like global and local air-/fuel ratio, external EGR and fuel rail pressure as well as the influence of fuel parameters are discussed giving a characterization of the combustion process of stratified engine operation. Furthermore, the influences of non-inert exhaust gas components on engine knock tendency are investigated using external EGR with an EGR catalyst. Opposing the results to numerical analysis, combustion characteristics of turbo charged DISI-engines are presented. (orig.)

  3. Internal combustion engines in hybrid vehicles

    NARCIS (Netherlands)

    Mourad, S.; Weijer, C.J.T. van de; Beckman, D.E.

    1998-01-01

    In this paper the use of internal combustion engines in hybrid powertrains is investigated. The substantial difference between the use of internal combustion engines in conventional and in hybrid vehicles mean that engines for hybrid vehicles should be designed specifically for the purpose. At the

  4. Modeling the internal combustion engine

    Science.gov (United States)

    Zeleznik, F. J.; Mcbride, B. J.

    1985-01-01

    A flexible and computationally economical model of the internal combustion engine was developed for use on large digital computer systems. It is based on a system of ordinary differential equations for cylinder-averaged properties. The computer program is capable of multicycle calculations, with some parameters varying from cycle to cycle, and has restart capabilities. It can accommodate a broad spectrum of reactants, permits changes in physical properties, and offers a wide selection of alternative modeling functions without any reprogramming. It readily adapts to the amount of information available in a particular case because the model is in fact a hierarchy of five models. The models range from a simple model requiring only thermodynamic properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. Among its many features the model includes heat transfer, valve timing, supercharging, motoring, finite burning rates, cycle-to-cycle variations in air-fuel ratio, humid air, residual and recirculated exhaust gas, and full combustion kinetics.

  5. Nanoparticle emissions from combustion engines

    CERN Document Server

    Merkisz, Jerzy

    2015-01-01

     This book focuses on particulate matter emissions produced by vehicles with combustion engines. It describes the physicochemical properties of the particulate matter, the mechanisms of its formation and its environmental impacts (including those on human beings). It discusses methods for measuring particulate mass and number, including the state-of-the-art in Portable Emission Measurement System (PEMS) equipment for measuring the exhaust emissions of both light and heavy-duty vehicles and buses under actual operating conditions. The book presents the authors’ latest investigations into the relations between particulate emission (mass and number) and engine operating parameters, as well as their new findings obtained through road tests performed on various types of vehicles, including those using diesel particulate filter regeneration. The book, which addresses the needs of academics and professionals alike, also discusses relevant European regulations on particulate emissions and highlights selected metho...

  6. Time Resolved FTIR Analysis of Combustion of Ethanol and Gasoline Combustion in AN Internal Combustion Engine

    Science.gov (United States)

    White, Allen R.; Sakai, Stephen; Devasher, Rebecca B.

    2011-06-01

    In order to pursue In Situ measurements in an internal combustion engine, a MegaTech Mark III transparent spark ignition engine was modified with a sapphire combustion chamber. This modification will allow the transmission of infrared radiation for time-resolved spectroscopic measurements by an infrared spectrometer. By using a Step-scan equipped Fourier transform spectrometer, temporally resolved infrared spectral data were acquired and compared for combustion in the modified Mark III engine. Measurements performed with the FTIR system provide insight into the energy transfer vectors that precede combustion and also provides an in situ measurement of the progress of combustion. Measurements were performed using ethanol and gasoline.

  7. Combustion diagnostic for active engine feedback control

    Science.gov (United States)

    Green, Jr., Johney Boyd; Daw, Charles Stuart; Wagner, Robert Milton

    2007-10-02

    This invention detects the crank angle location where combustion switches from premixed to diffusion, referred to as the transition index, and uses that location to define integration limits that measure the portions of heat released during the combustion process that occur during the premixed and diffusion phases. Those integrated premixed and diffusion values are used to develop a metric referred to as the combustion index. The combustion index is defined as the integrated diffusion contribution divided by the integrated premixed contribution. As the EGR rate is increased enough to enter the low temperature combustion regime, PM emissions decrease because more of the combustion process is occurring over the premixed portion of the heat release rate profile and the diffusion portion has been significantly reduced. This information is used to detect when the engine is or is not operating in a low temperature combustion mode and provides that feedback to an engine control algorithm.

  8. Internal combustion engine and method for control

    Science.gov (United States)

    Brennan, Daniel G

    2013-05-21

    In one exemplary embodiment of the invention an internal combustion engine includes a piston disposed in a cylinder, a valve configured to control flow of air into the cylinder and an actuator coupled to the valve to control a position of the valve. The internal combustion engine also includes a controller coupled to the actuator, wherein the controller is configured to close the valve when an uncontrolled condition for the internal engine is determined.

  9. Internal Combustion Engines as Fluidized Bed Reactors

    Science.gov (United States)

    Lavich, Zoe; Taie, Zachary; Menon, Shyam; Beckwith, Walter; Daly, Shane; Halliday, Devin; Hagen, Christopher

    2016-11-01

    Using an internal combustion engine as a chemical reactor could provide high throughput, high chemical conversion efficiency, and reactant/product handling benefits. For processes requiring a solid catalyst, the ability to develop a fluidized bed within the engine cylinder would allow efficient processing of large volumes of fluid. This work examines the fluidization behavior of particles in a cylinder of an internal combustion engine at various engine speeds. For 40 micron silica gel particles in a modified Megatech Mark III transparent combustion engine, calculations indicate that a maximum engine speed of about 60.8 RPM would result in fluidization. At higher speeds, the fluidization behavior is expected to deteriorate. Experiments gave qualitative confirmation of the analytical predictions, as a speed of 48 RPM resulted in fluidized behavior, while a speed of 171 RPM did not. The investigation shows that under certain conditions a fluidized bed can be obtained within an engine cylinder. Corresponding Author.

  10. Combustion Limits and Efficiency of Turbojet Engines

    Science.gov (United States)

    Barnett, H. C.; Jonash, E. R.

    1956-01-01

    Combustion must be maintained in the turbojet-engine combustor over a wide range of operating conditions resulting from variations in required engine thrust, flight altitude, and flight speed. Furthermore, combustion must be efficient in order to provide the maximum aircraft range. Thus, two major performance criteria of the turbojet-engine combustor are (1) operatable range, or combustion limits, and (2) combustion efficiency. Several fundamental requirements for efficient, high-speed combustion are evident from the discussions presented in chapters III to V. The fuel-air ratio and pressure in the burning zone must lie within specific limits of flammability (fig. 111-16(b)) in order to have the mixture ignite and burn satisfactorily. Increases in mixture temperature will favor the flammability characteristics (ch. III). A second requirement in maintaining a stable flame -is that low local flow velocities exist in the combustion zone (ch. VI). Finally, even with these requirements satisfied, a flame needs a certain minimum space in which to release a desired amount of heat, the necessary space increasing with a decrease in pressure (ref. 1). It is apparent, then, that combustor design and operation must provide for (1) proper control of vapor fuel-air ratios in the combustion zone at or near stoichiometric, (2) mixture pressures above the minimum flammability pressures, (3) low flow velocities in the combustion zone, and (4) adequate space for the flame.

  11. Two phase exhaust for internal combustion engine

    Science.gov (United States)

    Vuk, Carl T [Denver, IA

    2011-11-29

    An internal combustion engine having a reciprocating multi cylinder internal combustion engine with multiple valves. At least a pair of exhaust valves are provided and each supply a separate power extraction device. The first exhaust valves connect to a power turbine used to provide additional power to the engine either mechanically or electrically. The flow path from these exhaust valves is smaller in area and volume than a second flow path which is used to deliver products of combustion to a turbocharger turbine. The timing of the exhaust valve events is controlled to produce a higher grade of energy to the power turbine and enhance the ability to extract power from the combustion process.

  12. Internal and Surface Phenomena in Heterogenous Metal Combustion

    Science.gov (United States)

    Dreizin, Edward L.

    1997-01-01

    The phenomenon of gas dissolution in burning metals was observed in recent metal combustion studies, but it could not be adequately explained by the traditional metal combustion models. The research reported here addresses heterogeneous metal combustion with emphasis on the processes of oxygen penetration inside burning metal and its influence on the metal combustion rate, temperature history, and disruptive burning. The unique feature of this work is the combination of the microgravity environment with a novel micro-arc generator of monodispersed metal droplets, ensuring repeatable formation and ignition of uniform metal droplets with a controllable initial temperature and velocity. Burning droplet temperature is measured in real time with a three wavelength pyrometer. In addition, particles are rapidly quenched at different combustion times, cross-sectioned, and examined using SEM-based techniques to retrieve the internal composition history of burning metal particles. When the initial velocity of a spherical particle is nearly zero, the microgravity environment makes it possible to study the flame structure, the development of flame nonsymmetry, and correlation of the flame shape with the heterogeneous combustion processes.

  13. External combustion wankel engine for solar applications

    Energy Technology Data Exchange (ETDEWEB)

    Kovarsky, N.; Kaftori, D.; Gamzon, E.; Dgani, E. [Silver Arrow (Israel)

    1999-03-01

    An External Combustion Wankel Engine (ECWE), intended for use in a dish-engine solar power plant is discussed. The engine operates in a Brayton cycle using a gaseous working fluid, which is heated outside of the engine by concentrated solar radiation or fossil fuel. A computer simulation code that models the ECWE's operation and performance has been developed The program takes into account all of the engine's characteristics, subsystems and operating conditions. In the present work, the advantages and features of ECWE are considered in detail, together with simulation results of its performance. (authors)

  14. Multidimensional modeling of Dimethyl Ether(DME) spray combustion in DI diesel engine

    Institute of Scientific and Technical Information of China (English)

    WEN Hua; LIU Yong-chang; WEI Ming-rui; ZHANG Yu-sheng

    2005-01-01

    In the present study a modified CFD code KIVA3V was used to simulate the spray combustion in a small DI diesel engine fueled with DME. The improved spray models consider more spray phenomena such as cavitation flow in nozzle hole, jet atomization, droplet second breakup and spray wall interaction. Otherwise, a reduced DME reaction mechanism is implemented in the combustion model, and a new turbulent combustion model-Partial Stirred Reactor (PaSR) model is selected to simulate the spray combustion process, the effects of turbulent mixing on the reaction rate are considered. The results of engine modeling based on those models agreed well with the experimental measurements. Study of temperature fields variation and particle traces in the combustion chamber revealed that the engine combustion system originally used for diesel fuel must be optimized for DME.

  15. Engine combustion control via fuel reactivity stratification

    Energy Technology Data Exchange (ETDEWEB)

    Reitz, Rolf Deneys; Hanson, Reed M.; Splitter, Derek A.; Kokjohn, Sage L.

    2016-06-28

    A compression ignition engine uses two or more fuel charges having two or more reactivities to control the timing and duration of combustion. In a preferred implementation, a lower-reactivity fuel charge is injected or otherwise introduced into the combustion chamber, preferably sufficiently early that it becomes at least substantially homogeneously dispersed within the chamber before a subsequent injection is made. One or more subsequent injections of higher-reactivity fuel charges are then made, and these preferably distribute the higher-reactivity matter within the lower-reactivity chamber space such that combustion begins in the higher-reactivity regions, and with the lower-reactivity regions following thereafter. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot).

  16. Engine combustion control via fuel reactivity stratification

    Energy Technology Data Exchange (ETDEWEB)

    Reitz, Rolf Deneys; Hanson, Reed M.; Splitter, Derek A.; Kokjohn, Sage L.

    2015-07-14

    A compression ignition engine uses two or more fuel charges having two or more reactivities to control the timing and duration of combustion. In a preferred implementation, a lower-reactivity fuel charge is injected or otherwise introduced into the combustion chamber, preferably sufficiently early that it becomes at least substantially homogeneously dispersed within the chamber before a subsequent injection is made. One or more subsequent injections of higher-reactivity fuel charges are then made, and these preferably distribute the higher-reactivity matter within the lower-reactivity chamber space such that combustion begins in the higher-reactivity regions, and with the lower-reactivity regions following thereafter. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot).

  17. Engine combustion control via fuel reactivity stratification

    Science.gov (United States)

    Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

    2013-12-31

    A compression ignition engine uses two or more fuel charges having two or more reactivities to control the timing and duration of combustion. In a preferred implementation, a lower-reactivity fuel charge is injected or otherwise introduced into the combustion chamber, preferably sufficiently early that it becomes at least substantially homogeneously dispersed within the chamber before a subsequent injection is made. One or more subsequent injections of higher-reactivity fuel charges are then made, and these preferably distribute the higher-reactivity matter within the lower-reactivity chamber space such that combustion begins in the higher-reactivity regions, and with the lower-reactivity regions following thereafter. By appropriately choose the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot).

  18. Computational transport phenomena for engineering analyses

    CERN Document Server

    Farmer, Richard C; Cheng, Gary C; Chen, Yen-Sen

    2009-01-01

    Computational Transport PhenomenaOverviewTransport PhenomenaAnalyzing Transport PhenomenaA Computational Tool: The CTP CodeVerification, Validation, and GeneralizationSummaryNomenclatureReferencesThe Equations of ChangeIntroductionDerivation of The Continuity EquationDerivation of The Species Continuity EquationDerivation of The Equation Of MotionDerivation of The General Energy EquationNon-Newtonian FluidsGeneral Property BalanceAnalytical and Approximate Solutions for the Equations of ChangeSummaryNomenclatureReferencesPhysical PropertiesOverviewReal-Fluid ThermodynamicsChemical Equilibrium

  19. Wear aspects of internal combustion engine valves

    Science.gov (United States)

    Panţuru, M.; Chicet, D.; Paulin, C.; Alexandru, A.; Munteanu, C.

    2016-08-01

    Because the surface engineering is becoming an increasingly viable alternative to the constructive changes made to improve the efficiency of internal combustion engines, have been proposed and tested various types of coatings of some organs of internal combustion engines. One vital organ is the engine valves, which is subjected during operation to combined thermal, mechanical, corrosion and wear solicitations, which are leading to severe corrosion and complete breakdown. In this paper were analyzed aspects of valves wear and the active surfaces were coated using the atmospheric plasma spraying method (APS) with two commercial powders: Ni-Al and YSZ. Microstructural analyzes were made on these layers and also observations regarding the possibility of using them as thermal barrier and anti-oxidant coatings.

  20. Chemical Kinetic Models for Advanced Engine Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Pitz, William J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mehl, Marco [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Westbrook, Charles K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2014-10-22

    The objectives for this project are as follows: Develop detailed chemical kinetic models for fuel components used in surrogate fuels for compression ignition (CI), homogeneous charge compression ignition (HCCI) and reactivity-controlled compression-ignition (RCCI) engines; and Combine component models into surrogate fuel models to represent real transportation fuels. Use them to model low-temperature combustion strategies in HCCI, RCCI, and CI engines that lead to low emissions and high efficiency.

  1. Improvement of D.I. diesel engine combustion using numerical simulation; Chokufun diesel kikan no nensho kaizen shuho. Suchi kaiseki ni yoru torikumi

    Energy Technology Data Exchange (ETDEWEB)

    Minami, T.; Adachi, T.; Isyii, Y. [Isuzu Motors Ltd., Tokyo (Japan)

    1999-04-01

    For the purpose of improving DI diesel engine combustion, it is important to predict air flow of intake and exhaust manifold, intake port flow, combustion chamber swirl and fuel spray combustion. This paper describes the application of numerical simulation to the engines, the analysis of phenomena and a problem of simulation model modification. (author)

  2. ABB Combustion Engineering`s nuclear experience and technologies

    Energy Technology Data Exchange (ETDEWEB)

    Matzie, R.A.

    1994-12-31

    ABB Combustion Engineering`s nuclear experience and technologies are outlined. The following topics are discussed: evolutionary approach using proven technology, substantial improvement to plant safety, utility perspective up front in developing design, integrated design, competitive plant cost, operability and maintainability, standardization, and completion of US NRC technical review.

  3. COMBUSTION SIMULATION IN A SPARK IGNITION ENGINE CYLINDER: EFFECTS OF AIR-FUEL RATIO ON THE COMBUSTION DURATION

    OpenAIRE

    2010-01-01

    Combustion is an important subject of internal combustion engine studies. To reduce the air pollution from internal combustion engines and to increase the engine performance, it is required to increase combustion efficiency. In this study, effects of air/fuel ratio were investigated numerically. An axisymmetrical internal combustion engine was modeled in order to simulate in-cylinder engine flow and combustion. Two dimensional transient continuity, momentum, turbulence, energy, and combustion...

  4. Self-ignition phenomena in DI gasoline engines; Selbstzuendungsphaenomene in Ottomotoren mit Direkteinspritzung

    Energy Technology Data Exchange (ETDEWEB)

    Palaveev, Stefan [MOT Forschungs- und Entwicklungsgesellschaft fuer Motorentechnik, Optik und Thermodynamik mbH, Karlsruhe (Germany); Dahnz, Christoph [Karlsruhe Univ. (DE). Inst. fuer Kolbenmaschinen (IFKM)

    2010-07-01

    With the cost of natural resources rising and environmental awareness increasing, combustion engine manufacturers are focusing their research and development efforts on improving engine efficiency and reduction of exhaust emissions. Engine downsizing is one of the concepts that can reduce the fuel consumption of gasoline engines. Downsizing improves significantly the specific fuel consumption of part-load operating points by shifting them into engine operating map areas with better efficiencies. This is achieved by reducing engine displacement at constant engine speed. In order to obtain the same level of power output, the engines are boosted. However, this high level of power density and thermal loading at full-load operation can cause autoignition of the fuel-air-mixture. In addition to the engine knocking that is typical in spark ignition engines, other sporadic autoignition phenomena take place before the electrical spark breakdown. In the case of premature autoignition heat release starts well before TDC and results in steep rises in both pressure and temperature in the combustion chamber. Such enormous overloads could cause engine failure in a short time. This study aims to provide an overview of the theoretical basics of the autoignition processes at full load engine operation. It also analyzed the impact of some important factors, such as fuel and lubricant properties, mixture formation and injector position. Finally, the study discusses gasoline direct injection as a method to improve thermal efficiency in the context of full-load engine operation. (orig.)

  5. 30 CFR 57.4103 - Fueling internal combustion engines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fueling internal combustion engines. 57.4103... Prevention and Control Prohibitions/precautions/housekeeping § 57.4103 Fueling internal combustion engines. Internal combustion engines shall be switched off before refueling if the fuel tanks are integral parts of...

  6. 30 CFR 56.4103 - Fueling internal combustion engines.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Fueling internal combustion engines. 56.4103... Prevention and Control Prohibitions/precautions/housekeeping § 56.4103 Fueling internal combustion engines. Internal combustion engines shall be switched off before refueling if the fuel tanks are integral parts of...

  7. Deformation analysis of rotary combustion engine housings

    Science.gov (United States)

    Vilmann, Carl

    1991-01-01

    This analysis of the deformation of rotary combustion engine housings targeted the following objectives: (1) the development and verification of a finite element model of the trochoid housing, (2) the prediction of the stress and deformation fields present within the trochoid housing during operating conditions, and (3) the development of a specialized preprocessor which would shorten the time necessary for mesh generation of a trochoid housing's FEM model from roughly one month to approximately two man hours. Executable finite element models were developed for both the Mazda and the Outboard Marine Corporation trochoid housings. It was also demonstrated that a preprocessor which would hasten the generation of finite element models of a rotary engine was possible to develop. The above objectives are treated in detail in the attached appendices. The first deals with finite element modeling of a Wankel engine center housing, and the second with the development of a preprocessor that generates finite element models of rotary combustion engine center housings. A computer program, designed to generate finite element models of user defined rotary combustion engine center housing geometries, is also included.

  8. Supersonic combustion engine testbed, heat lightning

    Science.gov (United States)

    Hoying, D.; Kelble, C.; Langenbahn, A.; Stahl, M.; Tincher, M.; Walsh, M.; Wisler, S.

    1990-01-01

    The design of a supersonic combustion engine testbed (SCET) aircraft is presented. The hypersonic waverider will utilize both supersonic combustion ramjet (SCRAMjet) and turbofan-ramjet engines. The waverider concept, system integration, electrical power, weight analysis, cockpit, landing skids, and configuration modeling are addressed in the configuration considerations. The subsonic, supersonic and hypersonic aerodynamics are presented along with the aerodynamic stability and landing analysis of the aircraft. The propulsion design considerations include: engine selection, turbofan ramjet inlets, SCRAMjet inlets and the SCRAMjet diffuser. The cooling requirements and system are covered along with the topics of materials and the hydrogen fuel tanks and insulation system. A cost analysis is presented and the appendices include: information about the subsonic wind tunnel test, shock expansion calculations, and an aerodynamic heat flux program.

  9. Analysis of rocket engine injection combustion processes

    Science.gov (United States)

    Salmon, J. W.

    1976-01-01

    A critique is given of the JANNAF sub-critical propellant injection/combustion process analysis computer models and application of the models to correlation of well documented hot fire engine data bases. These programs are the distributed energy release (DER) model for conventional liquid propellants injectors and the coaxial injection combustion model (CICM) for gaseous annulus/liquid core coaxial injectors. The critique identifies model inconsistencies while the computer analyses provide quantitative data on predictive accuracy. The program is comprised of three tasks: (1) computer program review and operations; (2) analysis and data correlations; and (3) documentation.

  10. Experimental Studies of Hydrocarbon Flame Phenomena: Enabling Combustion Control

    Science.gov (United States)

    2016-07-30

    36 where Su 0 is the burning velocity of the pure fuel , Ea is the activation energy , R represents the universal gas constant, Tb is the mixture...K.M., 2009, “On diluted- fuel combustion issues in burning biogas surrogates,” ASME J. Energy Resour. Technol., 131(4), pp. 041802-041802-9. [8...Diluted MethaneFlames in the Near- andFar-Field , Journal of Energy Resources Technology, (12 2013): 0. doi: Andrew R. Hutchins, William A. Reach

  11. Combustion Engines Development Mixture Formation, Combustion, Emissions and Simulation

    CERN Document Server

    Schwarz, Christian; Teichmann, Rüdiger

    2012-01-01

    In the development of engines and vehicles it is nowadays standard practice to use commercially available computing programmes for simulation, not only of the transient reaction of vehicles or of the complete driveshaft, but also of the highly unsteady processes in the combustion chamber of an engine. Normally the source code is not available for these computing programmes and it takes too much time to study the respective specifications, so the users often do not have sufficient knowledge about the physical and chemical contents of the approaches that the programmes are based on. We have often been faced with this fact in talks to employees or in discussions during the presentation of results of simulation. Therefore it is our aim to point out different physical and chemical approaches and to show the possibilities and limits of the models used.

  12. Transport Phenomena and Interfacial Kinetics in Multiphase Combustion Systems. Revision

    Science.gov (United States)

    1992-08-01

    not be interpreted as necessarily the official policy or the endorsements, either expressed or implied, of the Air Force Office of Scientific Research...43 867. 1991 0021 8502,91 S3.00+O.0 Pnnted in Gmat Britain C 1991 Pupmon Prm pic CORRECTION FOR SAMPLING ERRORS DUE TO COAGULATION AND WALL LOSS IN...for Brownian aerosols (in the absence of appreciable inertial- and sedimentation-phenomena), as well as guide the design/selection of sampling systems

  13. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    NARCIS (Netherlands)

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion c

  14. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    NARCIS (Netherlands)

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion c

  15. Combustion and Engine-Core Noise

    Science.gov (United States)

    Ihme, Matthias

    2017-01-01

    The implementation of advanced low-emission aircraft engine technologies and the reduction of noise from airframe, fan, and jet exhaust have made noise contributions from an engine core increasingly important. Therefore, meeting future ambitious noise-reduction goals requires the consideration of engine-core noise. This article reviews progress on the fundamental understanding, experimental analysis, and modeling of engine-core noise; addresses limitations of current techniques; and identifies opportunities for future research. After identifying core-noise contributions from the combustor, turbomachinery, nozzles, and jet exhaust, they are examined in detail. Contributions from direct combustion noise, originating from unsteady combustion, and indirect combustion noise, resulting from the interaction of flow-field perturbations with mean-flow variations in turbine stages and nozzles, are analyzed. A new indirect noise-source contribution arising from mixture inhomogeneities is identified by extending the theory. Although typically omitted in core-noise analysis, the impact of mean-flow variations and nozzle-upstream perturbations on the jet-noise modulation is examined, providing potential avenues for future core-noise mitigation.

  16. Transport phenomena of reactive fluid flow in heterogeneous combustion processes.

    Science.gov (United States)

    Hung, W. S. Y.; Chen, C. S.; Haviland, J. K.

    1972-01-01

    A previously developed computer program was used to model two transient hybrid combustion processes involving tubes of solid Plexiglas. In the first study, representing combustion of a hybrid rocket, the oxidizing gas was oxygen, and calculations were continued sufficiently long to obtain steady-state values. Systematic variations were made in reaction rate constant, mass flow rate, and pressure, alternatively using constant and temperature dependent regression rate models for the fuel surface. Consistent results were obtained, as is evidenced by the values for the mass function of the reaction product and the flame temperature, for which plots are supplied. In the second study, fire initiation in a duct was studied, with an air mixture as the oxidizing gas. It was demonstrated that a satisfactory flame spread mechanism could be reproduced on the computer. In both of the above applications, the general, transient, two-dimensional conservation equations were represented, together with chemical reactions, solid-fuel interface conditions, and heat conduction in the solid fuel.

  17. Comparison of combustion efficiencies for ramjet engines

    Science.gov (United States)

    Bergmann, J. W.

    1984-01-01

    Four different combustion efficiencies commonly used for assessing ramjet engines are compared. The mixture ratios cover a range from stoichiometric to an equivalence ratio of 0.2, and the polyethylene/air propellant system is used. The ratio of effective to ideal temperature rise is taken as reference efficiency. As might be expected, major differences can be observed near stoichiometric and down to equilvalence ratios of 0.5. These are quantitatively demonstrated.

  18. Wall Effects on Combustion in an Engine.

    Science.gov (United States)

    1984-05-14

    AD-A41 418 WAL EFFECT ONCOMBUSTION INAN ENGNEU) TRW SPACE AND TECHNOLOGY GROUP REDONDO BEACH CA ENGINEERIHG S c SCENCES LAB E FENDEL 14 MUY 84 NRW-S...NO. NO. NO. 11. TITLE (Include Security Claaification, Wall Effects on Combustion in an Engine (U)7 12. PERSONAL AUTHOR(S) Fendell , Francis Edward 13a...heat transfer as a determent of end-gas knock in a homo- geneous-charge engine was undertaken (Carrier, Fendell , Fink, and Feldman 1984). The last

  19. Design of computer controlled combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Isermann, R.; Mueller, N. [Darmstadt University of Technology (Germany). Inst. of Automatic Control

    2003-12-01

    Globalization and growing new markets, as well as increasing emission and fuel consumption requirements, force the car manufacturers and their suppliers to develop new engine control strategies in shorter time periods. This can mainly be reached by development tools and an integrated hardware and software environment enabling rapid implementation and testing of advanced engine control algorithms. The structure of a rapid control prototyping (RCP) system is explained, which allows fast measurement signal evaluation, and rapid prototyping of advanced engine control algorithms. A hardware-in-the-loop simulator for diesel engine control design is illustrated, simulation results for a 40 tons truck are presented. Providing efficient engine models for the proposed development tools, a dynamic local linear neural network approach is explained and applied for modelling the NO{sub x} emission characteristics of a 1.9 1 direct injection diesel engine. Furthermore the application of a RCP system is exemplified by the application of combustion pressure based closed-loop ignition timing control for a SI engine. Experimental results are shown for a 1.01 SI engine on a dynamic engine test stand. (author)

  20. Optical investigations of combustion process in SI and CI engines fuelled with butanol blends

    Energy Technology Data Exchange (ETDEWEB)

    Marchitto, L.; Mazzei, A.; Merola, S.S.; Tornatore, C. [CNR Napoli, Naples (Italy). Istituto Motori; Valentino, G.

    2013-06-01

    The use of alternative fuels, as biodiesel and ethanol, for light duty engines to approach the target of low exhaust emissions without fuel economy and performance penalty has been widely investigated. Recently it is growing the interest in the butanol and bio-butanol as viable alternatives either single or blended with conventional based fuels. In this paper, butanol effects on combustion processes were investigated through conventional methods and optical diagnostics applied in the combustion chamber of a compression ignition engine and of a spark ignition engine. Blends of diesel and n-butanol were used in a common rail DI diesel engine running at different operating conditions. Fuel injection timing and oxygen at the intake were changed in a single cylinder compression ignition engine equipped with common rail multi-jets injection system. Spray combustion and pollutant formation were investigated though UV-visible digital imaging and natural emission spectroscopy. Flame emissions and spectroscopy were applied in an optically accessible cylinder of a port fuel-injection, spark-ignition engine with an external boosting device. The engine worked with a stoichiometric mixture at medium speed and boosting in wide open throttle condition. Normal and knocking combustion was tested. Experiments in both the engines demonstrated that butanol allowed to reduce carbonaceous compounds formation and soot emission and to decrease unpleasant effects related to the combustion process such as the fuel deposition burning. Moreover some emission bands of OH radicals could be used as feature of different phenomena related to the combustion process. (orig.)

  1. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    OpenAIRE

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion chamber. It destroys the thermal boundary layer wall increasing heat transfer and could lead to compromised performance, and ultimately to destruction of the engine and mission loss. The main object...

  2. Combustion

    CERN Document Server

    Glassman, Irvin

    1987-01-01

    Combustion, Second Edition focuses on the underlying principles of combustion and covers topics ranging from chemical thermodynamics and flame temperatures to chemical kinetics, detonation, ignition, and oxidation characteristics of fuels. Diffusion flames, flame phenomena in premixed combustible gases, and combustion of nonvolatile fuels are also discussed. This book consists of nine chapters and begins by introducing the reader to heats of reaction and formation, free energy and the equilibrium constants, and flame temperature calculations. The next chapter explores the rates of reactio

  3. High efficiency stoichiometric internal combustion engine system

    Science.gov (United States)

    Winsor, Richard Edward; Chase, Scott Allen

    2009-06-02

    A power system including a stoichiometric compression ignition engine in which a roots blower is positioned in the air intake for the engine to control air flow. Air flow is decreased during part power conditions to maintain the air-fuel ratio in the combustion chamber of the engine at stoichiometric, thus enabling the use of inexpensive three-way catalyst to reduce oxides of nitrogen. The roots blower is connected to a motor generator so that when air flow is reduced, electrical energy is stored which is made available either to the roots blower to temporarily increase air flow or to the system electrical load and thus recapture energy that would otherwise be lost in reducing air flow.

  4. Studies on pressure-gain combustion engines

    Science.gov (United States)

    Matsutomi, Yu

    Various aspects of the pressure-gain combustion engine are investigated analytically and experimentally in the current study. A lumped parameter model is developed to characterize the operation of a valveless pulse detonation engine. The model identified the function of flame quenching process through gas dynamic process. By adjusting fuel manifold pressure and geometries, the duration of the air buffer can be effectively varied. The parametric study with the lumped parameter model has shown that engine frequency of up to approximately 15 Hz is attainable. However, requirements for upstream air pressure increases significantly with higher engine frequency. The higher pressure requirement indicates pressure loss in the system and lower overall engine performance. The loss of performance due to the pressure loss is a critical issue for the integrated pressure-gain combustors. Two types of transitional methods are examined using entropy-based models. An accumulator based transition has obvious loss due to sudden area expansion, but it can be minimized by utilizing the gas dynamics in the combustion tube. An ejector type transition has potential to achieve performance beyond the limit specified by a single flow path Humphrey cycle. The performance of an ejector was discussed in terms of apparent entropy and mixed flow entropy. Through an ideal ejector, the apparent part of entropy increases due to the reduction in flow unsteadiness, but entropy of the mixed flow remains constant. The method is applied to a CFD simulation with a simple manifold for qualitative evaluation. The operation of the wave rotor constant volume combustion rig is experimentally examined. The rig has shown versatility of operation for wide range of conditions. Large pressure rise in the rotor channel and in a section of the exhaust duct are observed even with relatively large leakage gaps on the rotor. The simplified analysis indicated that inconsistent combustion is likely due to insufficient

  5. ANALYSIS OF INTERNAL COMBUSTION ENGINE WITH A NEW CONCEPT OF POROUS MEDIUM COMBUSTION FOR THE FUTURE CLEAN ENGINE

    Directory of Open Access Journals (Sweden)

    Ashok A Dhale

    2010-01-01

    Full Text Available At present, the emissions of internal combustion engine can only be improved by catalytic treatments of the exhaust gases. Such treatments, however, result in high costs and relatively low conversion efficiency. This suggests that a new combustion technique should be developed to yield improved primary combustion processes inside the engine with drastically reduced exhaust gas emissions. To fulfill all requirements, Dr. Franz Drust has proposed a new combustion concept to perform homogenous combustion in internal combustion engines. This concept used the porous medium combustion technique and is called "PM-engine". It is shown that the PM combustion technique can be applied to internal combustion engines. Theoretical considerations are presented for internal combustion engines, indicating that an overall improvement in thermal efficiency can be achieved for the PM-engine. This is explained and general performance of the new PM-engines is demonstrated for a single cylinder, water cooled, direct injection diesel engine. Verification of experiments at primary stage is described that were carried out as a part of the present study.

  6. Combustion Temperature Effect of Diesel Engine Convert to Compressed Natural Gas Engine

    OpenAIRE

    Semin; Abdul R. Ismail; Rosli A. Bakar

    2009-01-01

    Effect of combustion temperature in the engine cylinder of diesel engine convert to Compressed Natural Gas (CNG) engine was presents in this study. The objective of this study was to investigate the engine cylinder combustion temperature effect of diesel engine convert to CNG engine on variation engine speed. Problem statement: The hypothesis was that the lower performance of CNG engine was caused by the effect of lower in engine cylinder temperature. Are the CNG engine is lower cylinder temp...

  7. Statistics of indicated pressure in combustion engine.

    Science.gov (United States)

    Sitnik, L. J.; Andrych-Zalewska, M.

    2016-09-01

    The paper presents the classic form of pressure waveforms in burn chamber of diesel engine but based on strict analytical basis for amending the displacement volume. The pressure measurement results are obtained in the engine running on an engine dynamometer stand. The study was conducted by a 13-phase ESC test (European Stationary Cycle). In each test phase are archived 90 waveforms of pressure. As a result of extensive statistical analysis was found that while the engine is idling distribution of 90 value of pressure at any value of the angle of rotation of the crankshaft can be described uniform distribution. In the each point of characteristic of the engine corresponding to the individual phases of the ESC test, 90 of the pressure for any value of the angle of rotation of the crankshaft can be described as normal distribution. These relationships are verified using tests: Shapiro-Wilk, Jarque-Bera, Lilliefors, Anderson-Darling. In the following part, with each value of the crank angle, are obtain values of descriptive statistics for the pressure data. In its essence, are obtained a new way to approach the issue of pressure waveform analysis in the burn chamber of engine. The new method can be used to further analysis, especially the combustion process in the engine. It was found, e.g. a very large variances of pressure near the transition from compression to expansion stroke. This lack of stationarity of the process can be important both because of the emissions of exhaust gases and fuel consumption of the engine.

  8. Bulkhead insert for an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Maki, Clifford E.; Chottiner, Jeffrey Eliot; Williams, Rick L.; Thibault, Mark W.; Ervin, James Douglas; Boileau, James Maurice; McKeough, Bryan

    2017-08-01

    An engine includes a cylinder block defining at least one main bearing bulkhead adjacent to a cylinder, and a crankshaft rotatably housed within the block by a main bearing. A bulkhead insert has a cap portion, and an insert portion provided within the bulkhead. The insert portion has having first and second end regions connected by first and second straps. Each strap having a flanged beam cross section. The first and second ends of the insert portion are configured to connect a main bearing cap column to a cylinder head column. Each of the first and second end regions define at least one protrusion having a surface substantially normal to engine combustion and reactive loads. The cap portion is configured to mate with the first end region at the main bearing cap column and support the main bearing.

  9. Internal combustion engine using premixed combustion of stratified charges

    Science.gov (United States)

    Marriott, Craig D.; Reitz, Rolf D. (Madison, WI

    2003-12-30

    During a combustion cycle, a first stoichiometrically lean fuel charge is injected well prior to top dead center, preferably during the intake stroke. This first fuel charge is substantially mixed with the combustion chamber air during subsequent motion of the piston towards top dead center. A subsequent fuel charge is then injected prior to top dead center to create a stratified, locally richer mixture (but still leaner than stoichiometric) within the combustion chamber. The locally rich region within the combustion chamber has sufficient fuel density to autoignite, and its self-ignition serves to activate ignition for the lean mixture existing within the remainder of the combustion chamber. Because the mixture within the combustion chamber is overall premixed and relatively lean, NO.sub.x and soot production are significantly diminished.

  10. Internal combustion engine with compound air compression

    Energy Technology Data Exchange (ETDEWEB)

    Paul, M.A.; Paul, A.

    1991-10-15

    This patent describes an internal combustion engine in combination with a compound air compression system. It comprises: a reciprocator with at least one cylinder, at least one piston reciprocal in the cylinder and a combustion chamber formed in substantial part by portions of the piston and cylinder, the reciprocator having a drive shaft; a rotary compressor having a drive shaft mechanically coupled to the drive shaft of the reciprocator, the rotary compressor having a Wankel-type, three-lobe, epitrochiodal configuration sides having a conduit conjected to the reciprocator for supplying compressed air to the reciprocator; a turbocharged with a gas turbine and a turbocompressor, the turbocompressor having an air conduit connected to the expander side of the rotary compressor; and a bypass conduit with a valve means connecting the turbocharger to the reciprocator for supplying compressed air directly to the reciprocator wherein the drive shaft of the reciprocator and the drive shaft of the compressor have connecting means for transmitting mechanical energy to the reciprocator at mid to high operating speeds of the engine when the turbocharge supplies compressed air to the rotary compressor and, at least in part, drives the rotary compressor.

  11. Method and device for diagnosing and controlling combustion instabilities in internal combustion engines operating in or transitioning to homogeneous charge combustion ignition mode

    Science.gov (United States)

    Wagner, Robert M [Knoxville, TN; Daw, Charles S [Knoxville, TN; Green, Johney B [Knoxville, TN; Edwards, Kevin D [Knoxville, TN

    2008-10-07

    This invention is a method of achieving stable, optimal mixtures of HCCI and SI in practical gasoline internal combustion engines comprising the steps of: characterizing the combustion process based on combustion process measurements, determining the ratio of conventional and HCCI combustion, determining the trajectory (sequence) of states for consecutive combustion processes, and determining subsequent combustion process modifications using said information to steer the engine combustion toward desired behavior.

  12. Dimensionless Parameter Scaling of Diesel Engine Combustion

    Science.gov (United States)

    Dowling, David R.; Filipi, Zoran

    1996-11-01

    Combustion in a modern heavy-duty Diesel engine with direct radial fuel injection typically takes place in a short nearly-cylindrical volume at a rate determined by turbulent mixing. Simple dimensionless-parameter scaling laws for turbulent gas-phase mixing and heat transfer have been shown to be effective for a variety of (oxidizer) flow and (fuel) injection conditions within a cylindrical geometry (Edwards et al., AIChE J., Vol. 31, 516 [1985].) (Breidenthal et al., JFM, Vol. 219, 531 [1990].) (Dowling et al., AIAA J. Thermophys. & HT, Vol. 4, 504 [1990].). These studies were driven by chemical laser applications emphasizing long cylinders and sidewall injection. The current investigation seeks to determine the applicability of dimensionless parameter scaling to the instantaneous in-cylinder fuel burning rate in a multi-cylinder Diesel engine typical of Class VIII trucks. Comparisons are made between scaled and unscaled fuel burning rate, as inferred from time-resolved in-cylinder pressure measurements, across the test engine's normal operating range. This research is supported by the US Army Tank-Automotive Research, Development, and Engineering Center.

  13. Compounded turbocharged rotary internal combustion engine fueled with natural gas

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, P.E.

    1992-10-15

    This patent describes a compounded engine. It comprises: a first Wankel engine having a housing with a trochoidal inner surface containing a generally triangular shaped rotor, the engine containing a fuel supply system suitable for operating the engine with natural gas as a fuel; a turbocharge compressing air for combustion by the engine, the turbocharger being driven by the exhaust gases which exit from the engine; a combustion chamber in fluid communication with the exhaust from the engine after that exhaust has passed through the turbocharger, the chamber having an ignition device suitable for igniting hydrocarbons in the engine exhaust, whereby the engine timing, and the air and fuel mixture of the engine are controlled so that when the engine exhaust reaches the combustion chamber the exhaust contains a sufficient amount of oxygen and hydrocarbons to enable ignition and combustion of the engine exhaust in the combustion chamber without the addition of fuel or air, and whereby the engine operating conditions are controlled to vary the performance of the secondary combustor; and a controllable ignition device to ignite the exhaust gases in the combustion chamber at predetermined times.

  14. FY2014 Advanced Combustion Engine Annual Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2015-03-01

    The Advanced Combustion Engine research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research focuses on addressing critical barriers to commercializing higher efficiency, very low emissions advanced internal combustion engines for passenger and commercial vehicles.

  15. FY2015 Advanced Combustion Engine Annual Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Gurpreet [Vehicle Technologies Office, Washington, DC (United States); Gravel, Roland M. [Vehicle Technologies Office, Washington, DC (United States); Howden, Kenneth C. [Vehicle Technologies Office, Washington, DC (United States); Breton, Leo [Vehicle Technologies Office, Washington, DC (United States)

    2016-03-25

    The Advanced Combustion Engine research and development (R&D) subprogram within the DOE Vehicle Technologies Office (VTO) provides support and guidance for many cutting-edge automotive technologies under development. Research focuses on addressing critical barriers to commercializing higher efficiency, very low emissions advanced internal combustion engines for passenger and commercial vehicles.

  16. Combustion characteristics of lemongrass (Cymbopogon flexuosus oil in a partial premixed charge compression ignition engine

    Directory of Open Access Journals (Sweden)

    Avinash Alagumalai

    2015-09-01

    Full Text Available Indeed, the development of alternate fuels for use in internal combustion engines has traditionally been an evolutionary process in which fuel-related problems are met and critical fuel properties are identified and their specific limits defined to resolve the problem. In this regard, this research outlines a vision of lemongrass oil combustion characteristics. In a nut-shell, the combustion phenomena of lemongrass oil were investigated at engine speed of 1500 rpm and compression ratio of 17.5 in a 4-stroke cycle compression ignition engine. Furthermore, the engine tests were conducted with partial premixed charge compression ignition-direct injection (PCCI-DI dual fuel system to profoundly address the combustion phenomena. Analysis of cylinder pressure data and heat-release analysis of neat and premixed lemongrass oil were demonstrated in-detail and compared with conventional diesel. The experimental outcomes disclosed that successful ignition and energy release trends can be obtained from a compression ignition engine fueled with lemongrass oil.

  17. Comparisons between measurement and analysis of fluid motion in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Witze, P.O. (ed.)

    1981-10-01

    The Engine Combustion Technology Project was created for the purpose of promoting the development of advanced piston engine concepts by the development of techniques to measure, analyze, and understand the combustion process. The technologies emphasized in the project include laser-based measurement techniques and large-scale computer simulations. Considerable progress has already been achieved by project participants in modeling engine air motion, fuel sprays, and engine combustion phenomena. This milestone report covers one part of that progress, summarizing the current capabilities of multi-dimensional computer codes being developed by the project to predict the behavior of turbulent air motion in an engine environment. Computed results are compared directly with experimental data in six different areas of importance to internal combustion engines: (1) Induction-generated ring-vortex structures; (2) Piston-induced vortex roll-up; (3) Behavior of turbulence during compression; (4) Decay of swirling flow during compression; (5) Decay of swirling flow in a constant volume engine simulator; (6) Exhaust-pipe flow. The computational procedures used include vortex dynamics, rapid distortion theory, and finite difference models employing two-equation and subgrid-scale turbulence models. Although the capability does not yet exist to predict the air motion in an engine from its geometric configuration alone, the results presented show that many flowfield sub-processes can be predicted given well-specified initial and boundary conditions.

  18. Variable compression ratio device for internal combustion engine

    Science.gov (United States)

    Maloney, Ronald P.; Faletti, James J.

    2004-03-23

    An internal combustion engine, particularly suitable for use in a work machine, is provided with a combustion cylinder, a cylinder head at an end of the combustion cylinder and a primary piston reciprocally disposed within the combustion cylinder. The cylinder head includes a secondary cylinder and a secondary piston reciprocally disposed within the secondary cylinder. An actuator is coupled with the secondary piston for controlling the position of the secondary piston dependent upon the position of the primary piston. A communication port establishes fluid flow communication between the combustion cylinder and the secondary cylinder.

  19. Internal combustion engine for natural gas compressor operation

    Energy Technology Data Exchange (ETDEWEB)

    Hagen, Christopher; Babbitt, Guy

    2016-12-27

    This application concerns systems and methods for compressing natural gas with an internal combustion engine. In a representative embodiment, a method is featured which includes placing a first cylinder of an internal combustion engine in a compressor mode, and compressing a gas within the first cylinder, using the cylinder as a reciprocating compressor. In some embodiments a compression check valve system is used to regulate pressure and flow within cylinders of the engine during a compression process.

  20. Acoustic resonance phenomena in air bleed channels in aviation engines

    Science.gov (United States)

    Aleksentsev, A. A.; Sazhenkov, A. N.; Sukhinin, S. V.

    2016-11-01

    The existence of axial-radial acoustic resonance oscillations of the basic air flow in bleed channels of aviation engines is demonstrated theoretically and experimentally. Numerical and analytical methods are used to determine the frequency of acoustic resonance oscillations for the lowest modes of open and closed bleed channels of the PS-90A engine. Experimental investigations reveal new acoustic resonance phenomena arising in the air flow in bleed channel cavities in the core duct of this engine owing to instability of the basic air flow. The results of numerical, analytical, and experimental studies of the resonance frequencies reached in the flow in bleed channel cavities in the core duct of the PS-90A engine are found to be in reasonable agreement. As a result, various types of resonance oscillations in bleed channels can be accurately described.

  1. Potential of Porous-Media Combustion Technology as Applied to Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Miroslaw Weclas

    2010-01-01

    Full Text Available The paper summarizes the knowledge concerning porous media combustion techniques as applied in engines. One of most important reasons of this review is to introduce this still not well known technology to researchers doing with internal combustion engine processes, thermal engines, reactor thermodynamics, combustion, and material science. The paper gives an overview of possible applications of a highly porous open cell structures to in-cylinder processes. This application means utilization of unique features of porous media for supporting engine processes, especially fuel distribution in space, vaporization, mixing with air, heat recuperation, ignition and combustion. There are three ways for applying porous medium technology to engines: support of individual processes, support of homogeneous combustion process (catalytic and non-catalytic with temperature control, and utilization of the porous structure as a heat capacitor only. In the first type of application, the porous structure may be utilized for fuel vaporization and improved fuel distribution in space making the mixture more homogeneous in the combustion chamber. Extension of these processes to mixture formation and ignition inside a combustion reactor allows the realization of a homogeneous and a nearly zero emissions level combustion characterized by a homogeneous temperature field at reduced temperature level.

  2. Rotary-piston internal combustion engine. Rotationskolbenbrennkraftmaschine

    Energy Technology Data Exchange (ETDEWEB)

    Eiermann, D.

    1991-08-08

    Rotary-piston internal combustion engine in trochoidal design with a slide bearing piston which is controlled by a synchronous gear. The gear is covered by an insert unit which is screwed at the eccentric. The insert unit seals the synchronous gear from the remaining machine parts; it has a hollow cylinder which covers the hollow gear of the synchronous gear and is eccentric to the eccentric shaft; it is sealed with a sealing ring from a shoulder of the piston. A further hollow cylinder is coaxial to the eccentric shaft; it surrounds the mount part with a clearance for the pinion; it projects into the boring at the side of the shaft and it is sealed by a sealing ring from the boring. An annular space which is sealed from the remaining engine rooms is on the other side of the bearing. The oil which escapes from the bearing is led from this annular space through the cooling rooms of the piston to the synchronous gear. The oil is carried off into a drain channel through the space which is formed by the coaxial hollow cylinder in the sidewall.

  3. Signal Processing Methods for Liquid Rocket Engine Combustion Spontaneous Stability and Rough Combustion Assessments

    Science.gov (United States)

    Kenny, R. Jeremy; Casiano, Matthew; Fischbach, Sean; Hulka, James R.

    2012-01-01

    Liquid rocket engine combustion stability assessments are traditionally broken into three categories: dynamic stability, spontaneous stability, and rough combustion. This work focuses on comparing the spontaneous stability and rough combustion assessments for several liquid engine programs. The techniques used are those developed at Marshall Space Flight Center (MSFC) for the J-2X Workhorse Gas Generator program. Stability assessment data from the Integrated Powerhead Demonstrator (IPD), FASTRAC, and Common Extensible Cryogenic Engine (CECE) programs are compared against previously processed J-2X Gas Generator data. Prior metrics for spontaneous stability assessments are updated based on the compilation of all data sets.

  4. Signal Processing Methods for Liquid Rocket Engine Combustion Spontaneous Stability and Rough Combustion Assessments

    Science.gov (United States)

    Kenny, R. Jeremy; Casiano, Matthew; Fischbach, Sean; Hulka, James R.

    2012-01-01

    Liquid rocket engine combustion stability assessments are traditionally broken into three categories: dynamic stability, spontaneous stability, and rough combustion. This work focuses on comparing the spontaneous stability and rough combustion assessments for several liquid engine programs. The techniques used are those developed at Marshall Space Flight Center (MSFC) for the J-2X Workhorse Gas Generator program. Stability assessment data from the Integrated Powerhead Demonstrator (IPD), FASTRAC, and Common Extensible Cryogenic Engine (CECE) programs are compared against previously processed J-2X Gas Generator data. Prior metrics for spontaneous stability assessments are updated based on the compilation of all data sets.

  5. Survey of Greener Ignition and Combustion Systems for Internal Combustion Engines

    OpenAIRE

    Luo, Wuqiao; Li, Yun; Tian, Zhong; Gao, Bo; Tong, Ling; Wang, Houjun; Zeng, Baoqing

    2015-01-01

    The spark and compression ignition principles of, petrol and diesel internal combustion engines (ICEs) have, not advanced for a century. These do not lead to complete, combustion and hence result in high exhaust emission and, low energy efficiency. This paper presents a comprehensive survey on the attempts and developments of greener ignition, and combustion systems for ICEs and points out that, homogeneous charge microwave ignition (HCMI) holds the, key to a perfect solution. Increasing the ...

  6. Liquid propellant rocket engine combustion simulation with a time-accurate CFD method

    Science.gov (United States)

    Chen, Y. S.; Shang, H. M.; Liaw, Paul; Hutt, J.

    1993-01-01

    Time-accurate computational fluid dynamics (CFD) algorithms are among the basic requirements as an engineering or research tool for realistic simulations of transient combustion phenomena, such as combustion instability, transient start-up, etc., inside the rocket engine combustion chamber. A time-accurate pressure based method is employed in the FDNS code for combustion model development. This is in connection with other program development activities such as spray combustion model development and efficient finite-rate chemistry solution method implementation. In the present study, a second-order time-accurate time-marching scheme is employed. For better spatial resolutions near discontinuities (e.g., shocks, contact discontinuities), a 3rd-order accurate TVD scheme for modeling the convection terms is implemented in the FDNS code. Necessary modification to the predictor/multi-corrector solution algorithm in order to maintain time-accurate wave propagation is also investigated. Benchmark 1-D and multidimensional test cases, which include the classical shock tube wave propagation problems, resonant pipe test case, unsteady flow development of a blast tube test case, and H2/O2 rocket engine chamber combustion start-up transient simulation, etc., are investigated to validate and demonstrate the accuracy and robustness of the present numerical scheme and solution algorithm.

  7. Parametric optimization of a new hybrid pneumatic-combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Higelin, P.; Vasile, I.; Charlet, A.; Chamaillard, Y. [Universite d' Orleans, LME-ESEM, Orleans (France)

    2004-06-01

    Although internal combustion engines display high overall maximum global efficiencies, this potential cannot be fully exploited in automotive applications: in real conditions, the average engine load (and thus efficiency) is quite low and the kinetic energy during a braking phase is lost. One solution to this problem is to switch to a new hybrid pneumatic-combustion engine concept, which is able to store energy in the form of compressed air. This energy can be issued from a braking phase or from a combustion phase at low power. The potential energy from the air tank can then be restored to start the engine, use the stored air to drive the engine as a pneumatic motor at low load or charge the engine at full load. Optimization of the compressed air tank maximum pressure and volume as well as the operating mode switching strategy provides an improvement in terms of fuel economy as high as 31 per cent if combined with engine downsizing. (Author)

  8. Towards a general turbulent combustion model for spark ignition engines

    Energy Technology Data Exchange (ETDEWEB)

    Naji, H.; Said, R.; Borghi, R.P.

    1989-01-01

    The prediction of combustion within spark ignition engines needs to take into account the interaction of turbulent fluctuations. Previous attempts at this used a model in which the chemical processes were supposed infinitely fast and the combustion was controlled by turbulent mixing only. This paper describes their progress in extending such models in two directions.

  9. Heat transfer in rocket engine combustion chambers and nozzles

    Science.gov (United States)

    Anderson, P. G.; Cheng, G. C.; Farmer, R. C.

    1993-01-01

    Complexities of liquid rocket engine heat transfer which involve the injector faceplate and regeneratively and film cooled walls are being investigated by computational analysis. A conjugate heat transfer analysis will be used to describe localized heating phenomena associated with particular injector configurations and coolant channels and film coolant dumps. These components are being analyzed, and the analyses verified with appropriate test data. Finally, the component analyses will be synthesized into an overall flowfield/heat transfer model. The FDNS code is being used to make the component analyses. Particular attention is being given to the representation of the thermodynamic properties of the fluid streams and to the method of combining the detailed models to represent overall heating. Unit flow models of specific coaxial injector elements have been developed and will be described. Since test data from the NLS development program are not available, new validation heat transfer data have been sought. Suitable data were obtained from a Rocketdyne test program on a model hydrocarbon/oxygen engine. Simulations of these test data will be presented. Recent interest in the hybrid motor have established the need for analyses of ablating solid fuels in the combustion chamber. Analysis of a simplified hybrid motor will also be presented.

  10. International evaluation of the programme on engine-related combustion

    Energy Technology Data Exchange (ETDEWEB)

    Arcoumanis, D. [Imperial College, London (United Kingdom); Greenhalgh, D. [Cranfield Univ. (United Kingdom); Magnusson, B.F. [Norwegian Univ. of Science and Technology, Trondheim (Norway); Peters, N. [Institut fuer Technische Mechanik, RWTH Aachen (Germany)

    1996-11-01

    The 12 projects in the engine related combustion programme cover the entire range from fundamental and theoretical aspects of combustion to more applied subjects such as engine control. The common denominator in the programme clearly is the internal combustion engine, both the reciprocating as well as the gas turbine engine. Such a large coverage by a relatively small number of projects necessarily leads to an isolation of some of the projects in terms of their subject as well as the methodology that is used. On the other hand, all the research areas of interest in combustion technology are represented by at least one of the projects. These are: mathematical and numerical methods in combustion; modelling of turbulent combustion; laser diagnostics of flows with combustion; studies of engine performance and their control; semi-empirical model development for practical applications. As a conclusion, the evaluation committee believes that the programme is well balanced between fundamental and applied projects. It covers the entire range of modern methodologies that are used on the international level and thereby contributes to the application and further development of these research tools in Sweden

  11. Thermodynamic Simulation of a Hybrid Pneumatic-Combustion Engine Concept

    Directory of Open Access Journals (Sweden)

    Yann Chamaillard

    2002-03-01

    Full Text Available Although internal combustion engines display high overall maximum global efficiencies, this potential cannot be fully exploited in automotive applications: in real conditions, the average engine load (and thus efficiency is quite low and the kinetic energy during a braking phase is lost. This work presents a new hybrid pneumatic-combustion engine and the associated thermodynamic cycles, which is able to store energy in the form of compressed air. This energy can be issued from a braking phase or from a combustion phase at low power. The potential energy from the air tank can then be restored to start the engine, or charge the engine at full load. The regenerative breaking and the suppression of the idling phases could provide an improvement in terms of fuel economy as high as 15% or more if combined with engine downsizing.

  12. A numerical study of turbulent combustion characteristics in a combustion chamber of a scramjet engine

    Institute of Scientific and Technical Information of China (English)

    LEE; ChunHian

    2010-01-01

    3D numerical simulation of flow fields in a combustion chamber of a scramjet engine using an SST turbulence model with an explicit compressibility correction was performed and the results were compared to the experimental results.The characteristics of the turbulent combustion flow fields were analyzed via the numerical results and presented.In order to identify the mechanisms of turbulent combustion in supersonic flows,the evolutions of governing dimensionless parameters in the flow fields were investigated based on the theory of combustion and the available numerical results.It was found that the supersonic combustion takes place in the region of fully developed turbulence and that the strongest effects of turbulence and combustion processes appear in the vicinity of the injector.The unsteady effects and the local flame extinction phenomenon induced by turbulent flows were found to be negligibly small,and the steady flamelet approximation will hold for practical applications.

  13. Real time identification of the internal combustion engine combustion parameters based on the vibration velocity signal

    Science.gov (United States)

    Zhao, Xiuliang; Cheng, Yong; Wang, Limei; Ji, Shaobo

    2017-03-01

    Accurate combustion parameters are the foundations of effective closed-loop control of engine combustion process. Some combustion parameters, including the start of combustion, the location of peak pressure, the maximum pressure rise rate and its location, can be identified from the engine block vibration signals. These signals often include non-combustion related contributions, which limit the prompt acquisition of the combustion parameters computationally. The main component in these non-combustion related contributions is considered to be caused by the reciprocating inertia force excitation (RIFE) of engine crank train. A mathematical model is established to describe the response of the RIFE. The parameters of the model are recognized with a pattern recognition algorithm, and the response of the RIFE is predicted and then the related contributions are removed from the measured vibration velocity signals. The combustion parameters are extracted from the feature points of the renovated vibration velocity signals. There are angle deviations between the feature points in the vibration velocity signals and those in the cylinder pressure signals. For the start of combustion, a system bias is adopted to correct the deviation and the error bound of the predicted parameters is within 1.1°. To predict the location of the maximum pressure rise rate and the location of the peak pressure, algorithms based on the proportion of high frequency components in the vibration velocity signals are introduced. Tests results show that the two parameters are able to be predicted within 0.7° and 0.8° error bound respectively. The increase from the knee point preceding the peak value point to the peak value in the vibration velocity signals is used to predict the value of the maximum pressure rise rate. Finally, a monitoring frame work is inferred to realize the combustion parameters prediction. Satisfactory prediction for combustion parameters in successive cycles is achieved, which

  14. Determination of combustion parameters using engine crankshaft speed

    Science.gov (United States)

    Taglialatela, F.; Lavorgna, M.; Mancaruso, E.; Vaglieco, B. M.

    2013-07-01

    Electronic engine controls based on real time diagnosis of combustion process can significantly help in complying with the stricter and stricter regulations on pollutants emissions and fuel consumption. The most important parameter for the evaluation of combustion quality in internal combustion engines is the in-cylinder pressure, but its direct measurement is very expensive and involves an intrusive approach to the cylinder. Previous researches demonstrated the direct relationship existing between in-cylinder pressure and engine crankshaft speed and several authors tried to reconstruct the pressure cycle on the basis of the engine speed signal. In this paper we propose the use of a Multi-Layer Perceptron neural network to model the relationship between the engine crankshaft speed and some parameters derived from the in-cylinder pressure cycle. This allows to have a non-intrusive estimation of cylinder pressure and a real time evaluation of combustion quality. The structure of the model and the training procedure is outlined in the paper. A possible combustion controller using the information extracted from the crankshaft speed information is also proposed. The application of the neural network model is demonstrated on a single-cylinder spark ignition engine tested in a wide range of speeds and loads. Results confirm that a good estimation of some combustion pressure parameters can be obtained by means of a suitable processing of crankshaft speed signal.

  15. Ducted combustion chamber for direct injection engines and method

    Science.gov (United States)

    Mueller, Charles

    2015-03-03

    An internal combustion engine includes an engine block having a cylinder bore and a cylinder head having a flame deck surface disposed at one end of the cylinder bore. A piston connected to a rotatable crankshaft and configured to reciprocate within the cylinder bore has a piston crown portion facing the flame deck surface such that a combustion chamber is defined within the cylinder bore and between the piston crown and the flame deck surface. A fuel injector having a nozzle tip disposed in fluid communication with the combustion chamber has at least one nozzle opening configured to inject a fuel jet into the combustion chamber along a fuel jet centerline. At least one duct defined in the combustion chamber between the piston crown and the flame deck surface has a generally rectangular cross section and extends in a radial direction relative to the cylinder bore substantially along the fuel jet centerline.

  16. Harmonic components of cylinder pressure variation and their characteristics for combustion noise in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.R.; Miyamoto, Noboru; Murayama, Tadashi

    1987-10-31

    Combustion noise is a serious problem in internal combustion engines, especially diesel engines. Although the cylinder pressure variation is easily visible tool to evaluate the combustion noise and thermal efficiency, the exciting force in engine combustion noise has not been completely determined. Cylinder pressure variation for different combustion behaviors and their harmonic components were calculated and an attempt was made to correlate the various components. It was found that the logarithmic harmonic components of cylinder pressure variations, the cylinder pressure level (CPL) can be described by a function with four variables, the values of cylinder pressure variation. The results of this paper is summarized as follows: 1) A relationship was established between CPL and four characteristic values describing the cylinder pressure and variation diagram. 2) Harmonic components of cylinder pressure variations are described by a linear function with four variables and four characteristic values. 3) In this case, the coefficients of the four variables depend solely on the order of engine revolutions and are independent of combustion behavior and engine operating conditions. (13 figs, 7 refs)

  17. FY 2007 Progress Report for Advanced Combustion Engine Technologies

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2007-12-01

    Advanced combustion engines have great potential for achieving dramatic energy efficiency improvements in light-duty vehicle applications, where it is suited to both conventional and hybrid- electric powertrain configurations. Light-duty vehicles with advanced combustion engines can compete directly with gasoline engine hybrid vehicles in terms of fuel economy and consumer-friendly driving characteristics; also, they are projected to have energy efficiencies that are competitive with hydrogen fuel cell vehicles when used in hybrid applications.Advanced engine technologies being researched and developed by the Advanced Combustion Engine R&D Sub-Program will also allow the use of hydrogen as a fuel in ICEs and will provide an energy-efficient interim hydrogen-based powertrain technology during the transition to hydrogen/fuelcell-powered transportation vehicles.

  18. Establishment of Combustion Model for Isooctane HCCI Marine Diesel Engine and Research on the Combustion Characteristic

    Directory of Open Access Journals (Sweden)

    Li Biao

    2016-01-01

    Full Text Available The homogeneous charge compression ignition (HCCI combustion mode applied in marine diesel engine is expected to be one of alternative technologies to decrease nitrogen oxide (NOX emission and improve energy utilization rate. Applying the chemical-looping combustion (CLC mechanism inside the cylinder, a numerical study on the HCCI combustion process is performed taking a marine diesel engine as application object. The characteristic feature of combustion process is displayed. On this basis, the formation and emission of NOX are analyzed and discussed. The results indicate that the HCCI combustion mode always exhibit two combustion releasing heats: low-temperature reaction and high-temperature reaction. The combustion phase is divided into low-temperature reaction zone, high-temperature reaction zone and negative temperature coefficient (NTC zone. The operating conditions of the high compression ratio, high intake air temperature, low inlet pressure and small excess air coefficient would cause the high in-cylinder pressure which often leads engine detonation. The low compression ratio, low intake air temperature and big excess air coefficient would cause the low combustor temperature which is conducive to reduce NOX emissions. These technological means and operating conditions are expected to meet the NOX emissions limits in MARPOL73/78 Convention-Annex VI Amendment.

  19. The Combination of Internal-Combustion Engine and Gas Turbine

    Science.gov (United States)

    Zinner, K.

    1947-01-01

    While the gas turbine by itself has been applied in particular cases for power generation and is in a state of promising development in this field, it has already met with considerable success in two cases when used as an exhaust turbine in connection with a centrifugal compressor, namely, in the supercharging of combustion engines and in the Velox process, which is of particular application for furnaces. In the present paper the most important possibilities of combining a combustion engine with a gas turbine are considered. These "combination engines " are compared with the simple gas turbine on whose state of development a brief review will first be given. The critical evaluation of the possibilities of development and fields of application of the various combustion engine systems, wherever it is not clearly expressed in the publications referred to, represents the opinion of the author. The state of development of the internal-combustion engine is in its main features generally known. It is used predominantly at the present time for the propulsion of aircraft and road vehicles and, except for certain restrictions due to war conditions, has been used to an increasing extent in ships and rail cars and in some fields applied as stationary power generators. In the Diesel engine a most economical heat engine with a useful efficiency of about 40 percent exists and in the Otto aircraft engine a heat engine of greatest power per unit weight of about 0.5 kilogram per horsepower.

  20. Development of High Efficiency Clean Combustion Engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, Craig; Gonzalez, Manual; Russell, Durrett

    2011-06-30

    This report summarizes activities related to the revised STATEMENT OF PROJECT OBJECTIVES (SOPO) dated June 2010 for the Development of High-Efficiency Clean Combustion engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines (COOPERATIVE AGREEMENT NUMBER DE-FC26-05NT42415) project. In both the spark- (SI) and compression-ignition (CI) development activities covered in this program, the goal was to develop potential production-viable internal combustion engine system technologies that both reduce fuel consumption and simultaneously met exhaust emission targets. To be production-viable, engine technologies were also evaluated to determine if they would meet customer expectations of refinement in terms of noise, vibration, performance, driveability, etc. in addition to having an attractive business case and value. Prior to this activity, only proprietary theoretical / laboratory knowledge existed on the combustion technologies explored The research reported here expands and develops this knowledge to determine series-production viability. Significant SI and CI engine development occurred during this program within General Motors, LLC over more than five years. In the SI program, several engines were designed and developed that used both a relatively simple multi-lift valve train system and a Fully Flexible Valve Actuation (FFVA) system to enable a Homogeneous Charge Compression Ignition (HCCI) combustion process. Many technical challenges, which were unknown at the start of this program, were identified and systematically resolved through analysis, test and development. This report documents the challenges and solutions for each SOPO deliverable. As a result of the project activities, the production viability of the developed clean combustion technologies has been determined. At this time, HCCI combustion for SI engines is not considered production-viable for several reasons. HCCI combustion is excessively sensitive to control variables

  1. Coal slurry combustion optimization on single cylinder engine

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    Under the sponsorship of the US Department of Energy, Morgantown Energy Technology Center, GE Transportation System has been conducting a proof of concept program to use coal water slurry (CWS) fuel to power a diesel engine locomotive since 1988. As reported earlier [1], a high pressure electronically controlled accumulator injector using a diamond compact insert nozzle was developed for this project. The improved reliability and durability of this new FIE allowed for an improved and more thorough study of combustion of CWS fuel in a diesel engine. It was decided to include a diesel pilot fuel injector in the combustion system mainly due to engine start and low load operation needs. BKM, Inc. of San Diego, CA was contracted to develop the electronic diesel fuel pilot/starting FIE for the research engine. As a result, the experimental combustion study was very much facilitated due to the ability of changing pilot/CWS injection timings and quantities without having to stop the engine. Other parameters studied included combustion chamber configuration (by changing CWS fuel injector nozzle hole number/shape/angle), as well as injection pressure. The initial phase of this combustion study is now complete. The results have been adopted into the design of a 12 cylinder engine FIE, to be tested in 1992. This paper summarizes the main findings of this study.

  2. EDWARDS' REFERENCE CYCLE FOR INTERNAL AND EXTERNAL COMBUSTION ENGINES

    Directory of Open Access Journals (Sweden)

    A. E. Piir

    2014-01-01

    Full Text Available Useful physical regularities of a reversible thermodynamic cycle for heat engines have been established in the paper. The engines are using fuel combustion products as a heat source, and the environment - as a heat sink that surpasses Carnot cycle according to efficiency factor.

  3. DYNAMIC DESIGN OF INTERNAL COMBUSTION ENGINE BLOCK STRUCTURE

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Several main steps of internal combustion engine block structure dynamic design,such as model set-up,structure dynamic response analysis,optimizing design and vibration and noise control,are discussed for the type of EQ6100 gasoline engine block.

  4. Engine combustion control at low loads via fuel reactivity stratification

    Science.gov (United States)

    Reitz, Rolf Deneys; Hanson, Reed M; Splitter, Derek A; Kokjohn, Sage L

    2014-10-07

    A compression ignition (diesel) engine uses two or more fuel charges during a combustion cycle, with the fuel charges having two or more reactivities (e.g., different cetane numbers), in order to control the timing and duration of combustion. By appropriately choosing the reactivities of the charges, their relative amounts, and their timing, combustion can be tailored to achieve optimal power output (and thus fuel efficiency), at controlled temperatures (and thus controlled NOx), and with controlled equivalence ratios (and thus controlled soot). At low load and no load (idling) conditions, the aforementioned results are attained by restricting airflow to the combustion chamber during the intake stroke (as by throttling the incoming air at or prior to the combustion chamber's intake port) so that the cylinder air pressure is below ambient pressure at the start of the compression stroke.

  5. CFD Studies of Combustion in Direct Injection Single Cylinder Diesel Engine Using Non-Premixed Combustion Model

    Directory of Open Access Journals (Sweden)

    S Gavudhama Karunanidhi

    2014-07-01

    Full Text Available In this study the simulation process of non-premixed combustion in a direct injection single cylinder diesel engine has been described. Direct injection diesel engines are used both in heavy duty vehicles and light duty vehicles. The fuel is injected directly into the combustion chamber. The fuel mixes with the high pressure air in the combustion chamber and combustion occurs. Due to the non-premixed nature of the combustion occurring in such engines, non-premixed combustion model of ANSYS FLUENT 14.5 can be used to simulate the combustion process. A 4-stroke diesel engine corresponds to one fuel injector hole without considering valves was modeled and combustion simulation process was studied. Here two types of combustion chambers were compared. Combustion studies of both chambers:- shallow depth and hemispherical combustion chambers were carried out. Emission characteristics of both combustion chambers had also been carried out. The obtained results are compared. It has been found that hemispherical combustion chamber is more efficient as it produces higher pressure and temperature compared to that of shallow depth combustion chamber. As the temperature increases the formation of NOx emissions and soot formation also get increased.

  6. Internal Combustion Engine Powered by Synthesis Gas from Pyrolysed Plastics

    Directory of Open Access Journals (Sweden)

    Chríbik Andrej

    2016-07-01

    Full Text Available The article discusses the application of synthesis gas from pyrolysis of plastics in petrol engine. The appropriate experimental measurements were performed on a combustion engine LGW 702 designated for micro-cogeneration unit. The power parameters, economic parameters in term of brake specific fuel consumption, and internal parameters of the engine were compared to the engine running on the reference fuel - natural gas and synthesis gas. Burning synthesis gas leads to decreased performance by about 5% and to increased mass hourly consumption by 120 %. In terms of burning, synthesis gas has similar properties as natural gas. Compared with [5] a more detailed study has been prepared on the effects of angle of spark advance on the engine torque, giving more detailed assessment of engine cycle variability and considering specification of start and end of combustion in the logarithm p-V diagram.

  7. Numerical Analysis on Combustion Characteristic of Leaf Spring Rotary Engine

    Directory of Open Access Journals (Sweden)

    Yan Zhang

    2015-08-01

    Full Text Available The purpose of this paper is to investigate combustion characteristics for rotary engine via numerical studies. A 3D numerical model was developed to study the influence of several operative parameters on combustion characteristics. A novel rotary engine called, “Leaf Spring Rotary Engine”, was used to illustrate the structure and principle of the engine. The aims are to (1 improve the understanding of combustion process, and (2 quantify the influence of rotational speed, excess air ratio, initial pressure and temperature on combustion characteristics. The chamber space changed with crankshaft rotation. Due to the complexity of chamber volume, an equivalent modeling method was presented to simulate the chamber space variation. The numerical simulations were performed by solving the incompressible, multiphase Unsteady Reynolds-Averaged Navier–Stokes Equations via the commercial code FLUENT using a transport equation-based combustion model; a realizable  turbulence model and finite-rate/eddy-dissipation model were used to account for the effect of local factors on the combustion characteristics.

  8. COMBUSTION SIMULATION IN A SPARK IGNITION ENGINE CYLINDER: EFFECTS OF AIR-FUEL RATIO ON THE COMBUSTION DURATION

    Directory of Open Access Journals (Sweden)

    Nureddin Dinler

    2010-01-01

    Full Text Available Combustion is an important subject of internal combustion engine studies. To reduce the air pollution from internal combustion engines and to increase the engine performance, it is required to increase combustion efficiency. In this study, effects of air/fuel ratio were investigated numerically. An axisymmetrical internal combustion engine was modeled in order to simulate in-cylinder engine flow and combustion. Two dimensional transient continuity, momentum, turbulence, energy, and combustion equations were solved. The k-e turbulence model was employed. The fuel mass fraction transport equation was used for modeling of the combustion. For this purpose a computational fluid dynamics code was developed by using the finite volume method with FORTRAN programming code. The moving mesh was utilized to simulate the piston motion. The developed code simulates four strokes of engine continuously. In the case of laminar flow combustion, Arrhenius type combustion equations were employed. In the case of turbulent flow combustion, eddy break-up model was employed. Results were given for rich, stoichiometric, and lean mixtures in contour graphs. Contour graphs showed that lean mixture (l = 1.1 has longer combustion duration.

  9. New controllable premixed combustion for dimethyl ether engine

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A new concept of the controllable premixed combustion (CPC) system was proposed for dimethyl ether (DME) to explore a new approach to achieving ultra-low NOX emissions with the zero level of particulate matter exhaust emissions. The DME fuel was injected into the premix chamber by means of the electronically controlled low pressure injection system, then the mixture formation and combustion process were controlled with a control-valve set between the main chamber and the premix chamber. The test bench was constructed based on a single diesel engine. Preliminary studies demonstrated that ultra-low NOX emissions had been realized with zero particulate matter emissions under the optimum specifications of the DME engine, NOX emissions were less than 65 × 10-6. According to the engine combustion analysis, it was found that the control-valve played an important role in the pre-mixture formation and ignition timing.

  10. Study Regarding the Identification of an Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Ioan Ruja

    2016-10-01

    Full Text Available The paper presents the results of the scientific investigations performed on an Otto engine. One conducted surveys on the analytic and experimental modelling of the internal combustion engine, considered as automated system element. The results of the analytical study are concretised in the mathematical model of the engine, expressed in the operational. The experimental results are concretised in the indicial response in rotating speed, as well as in the determination of the constants of interest. The investigation methods used in conducting the survey were: experimental identification based on the indicial response of the engine and the analytical identification based on the mathematical models of diverse engine subsystems.

  11. Combustion characteristics of an SI engine fueled with biogas fuel

    Science.gov (United States)

    Chen, Lei; Long, Wuqiang; Song, Peng

    2017-04-01

    An experimental research of the effect of H2 substitution and CO2 dilution on CH4 combustion has been carried out on a spark ignition engine. The results show that H2 addition could improve BMEP, thermal efficiency, CO and THC emissions. NOX emissions increased for higher low heating value (LHV) of H2 than CH4. CO2 dilution could effective reduce NOX emission of H2-CH4 combustion. Although engine performance, thermal efficiency and exhaust get unacceptable under high fuel dilution ratio (F.D.R.) conditions, it could be solved by decreasing F.D.R. and/or increasing hydrogen substitution ratio (H.S.R.).

  12. A statistical combustion phase control approach of SI engines

    Science.gov (United States)

    Gao, Jinwu; Wu, Yuhu; Shen, Tielong

    2017-02-01

    In order to maximize the performance of internal combustion engine, combustion phase is usually controlled to track its desired reference. However, suffering from the cyclic variability of combustion, it is difficulty but meaningful to control mean of combustion phase and constrain its variance. As a combustion phase indicator, the location of peak pressure (LPP) is utilized for real-time combustion phase control in this research. The purpose of the proposed method is to ensure the mean of LPP statistically tracks its reference and constrains the standard deviation of LPP distribution. To achieve this, LPP is first calculated based on the cylinder pressure sensor, and its characteristics are analyzed at the steady-state operating condition, then the distribution of LPP is examined online using hypothesis test criterion. On the basis of the presented statistical algorithm, current mean of LPP is applied in the feedback channel for designing spark advance adjustment law, and the stability of closed-loop system is theoretically ensured according to a steady statistical model. Finally, the proposed strategy is verified on a spark ignition gasoline engine.

  13. Fundamental phenomena on fuel decomposition and boundary layer combustion processes with applications to hybrid rocket motors

    Science.gov (United States)

    Kuo, Kenneth K.; Lu, Y. C.; Chiaverini, Martin J.; Harting, George C.

    1994-11-01

    An experimental study on the fundamental processes involved in fuel decomposition and boundary layer combustion in hybrid rocket motors is being conducted at the High Pressure Combustion Laboratory of the Pennsylvania State University. This research should provide a useful engineering technology base in the development of hybrid rocket motors as well as a fundamental understanding of the complex processes involved in hybrid propulsion. A high pressure slab motor has been designed and manufactured for conducting experimental investigations. Oxidizer (LOX or GOX) supply and control systems have been designed and partly constructed for the head-end injection into the test chamber. Experiments using HTPB fuel, as well as fuels supplied by NASA designated industrial companies will be conducted. Design and construction of fuel casting molds and sample holders have been completed. The portion of these items for industrial company fuel casting will be sent to the McDonnell Douglas Aerospace Corporation in the near future. The study focuses on the following areas: observation of solid fuel burning processes with LOX or GOX, measurement and correlation of solid fuel regression rate with operating conditions, measurement of flame temperature and radical species concentrations, determination of the solid fuel subsurface temperature profile, and utilization of experimental data for validation of a companion theoretical study (Part 2) also being conducted at PSU.

  14. Fundamental phenomena on fuel decomposition and boundary layer combustion processes with applications to hybrid rocket motors

    Science.gov (United States)

    Kuo, Kenneth K.; Lu, Y. C.; Chiaverini, Martin J.; Harting, George C.

    1994-01-01

    An experimental study on the fundamental processes involved in fuel decomposition and boundary layer combustion in hybrid rocket motors is being conducted at the High Pressure Combustion Laboratory of the Pennsylvania State University. This research should provide a useful engineering technology base in the development of hybrid rocket motors as well as a fundamental understanding of the complex processes involved in hybrid propulsion. A high pressure slab motor has been designed and manufactured for conducting experimental investigations. Oxidizer (LOX or GOX) supply and control systems have been designed and partly constructed for the head-end injection into the test chamber. Experiments using HTPB fuel, as well as fuels supplied by NASA designated industrial companies will be conducted. Design and construction of fuel casting molds and sample holders have been completed. The portion of these items for industrial company fuel casting will be sent to the McDonnell Douglas Aerospace Corporation in the near future. The study focuses on the following areas: observation of solid fuel burning processes with LOX or GOX, measurement and correlation of solid fuel regression rate with operating conditions, measurement of flame temperature and radical species concentrations, determination of the solid fuel subsurface temperature profile, and utilization of experimental data for validation of a companion theoretical study (Part 2) also being conducted at PSU.

  15. EXPERIMENTAL INVESTIGATION OF COMBUSTION, PERFORMANCE AND EMISSION CHARACTERISTICS OF DI DIESEL ENGINE UNDER HCCI MODE WITH POROUS MEDIUM COMBUSTION

    Directory of Open Access Journals (Sweden)

    C KANNAN

    2010-08-01

    Full Text Available In recent times, homogeneous combustion has been a proven technology to attain high efficient and low emission engines. Homogenous Charge Compression Ignition (HCCI engines are able to have efficiencies as high as Compression Ignition, Direct Injection (CIDI engines, while producing ultra-low emissions of nitrogen oxides (NOx and particulate matter (PM.HCCI combustion is achieved by controlling the temperature, pressure and composition of the fuel-air mixture so that it spontaneously gets ignited in the combustion chamber. Numeroustechniques such as Variable Exhaust Gas Recirculation (VEGR, ariable Compression Ratio (VCR and Variable Valve Timing (VVT have been proposed to control the homogeneous combustion inside the engine cylinder. Even though these techniques are attractive and having good time response, they are too expensive to afford. This paper investigates the performance, combustion and emission characteristics of a Direct Injection (DI diesel engine under HCCI mode which is established through an effective and affordable technique called Porous Medium Combustion (PMC.

  16. Exergetic analysis of cogeneration plants through integration of internal combustion engine and process simulators

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Leonardo de Oliveira [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)], E-mail: leonardo.carvalho@petrobras.com.br; Leiroz, Albino Kalab; Cruz, Manuel Ernani [Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE/UFRJ), RJ (Brazil). Programa de Engenharia Mecanica], Emails: leiroz@mecanica.ufrj.br, manuel@mecanica.ufrj.br

    2010-07-01

    Internal combustion engines (ICEs) have been used in industry and power generation much before they were massively employed for transportation. Their high reliability, excellent power-to-weight ratio, and thermal efficiency have made them a competitive choice as main energy converters in small to medium sized power plants. Process simulators can model ICE powered energy plants with limited depth, due to the highly simplified ICE models used. Usually a better understanding of the global effects of different engine parameters is desirable, since the combustion process within the ICE is typically the main cause of exergy destruction in systems which utilize them. Dedicated commercial ICE simulators have reached such a degree of maturity, that they can adequately model a wide spectrum of phenomena that occur in ICEs. However, ICE simulators are unable to incorporate the remaining of power plant equipment and processes in their models. This paper presents and exploits the integration of an internal combustion engine simulator with a process simulator, so as to evaluate the construction of a fully coupled simulation platform to analyze the performance of ICE-based power plants. A simulation model of an actual cogeneration plant is used as a vehicle for application of the proposed computational methodology. The results show that by manipulating the engine mapping parameters, the overall efficiency of the plant can be improved. (author)

  17. CAD/CAM/CAI Application for High-Precision Machining of Internal Combustion Engine Pistons

    Directory of Open Access Journals (Sweden)

    V. V. Postnov

    2014-07-01

    Full Text Available CAD/CAM/CAI application solutions for internal combustion engine pistons machining was analyzed. Low-volume technology of internal combustion engine pistons production was proposed. Fixture for CNC turning center was designed.

  18. Air supply system for an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Eftink, A.

    1992-06-11

    The present invention describes a system for supplying the primary combustion air to a reciprocating piston internal combustion engine including a trochoidal chamber air pump having a pair of pumping chambers interposed between an air intake and each of the cylinders of the engine. Each pumping chamber has an air inlet connected to an air intake, and an air outlet that is connected to the cylinders. In a two-cycle mode of operation, each pumping chamber outlet is connected to one engine cylinder. In a four-cycle mode of operation, each pumping chamber outlet is connected to a pair of cylinders to supply air during the intake stroke. The input shaft of the trochoidal chamber air pump is driven by, and may be connected to, the crankshaft of the engine so as to rate on a 1:1 ratio. (author)

  19. Synthesis Gas from Pyrolysed Plastics for Combustion Engine

    Directory of Open Access Journals (Sweden)

    Chríbik Andrej

    2015-12-01

    Full Text Available The article discusses the application of synthesis gas from pyrolysis of plastics in petrol engine. The appropriate experimental measurements were performed on a combustion engine LGW 702 designated for micro-cogeneration unit. The power parameters, economic and internal parameters of the engine were compared to the engine running on the reference fuel - natural gas and synthesis gas. Burning synthesis gas leads to decreased performance by about 5% and to increased mass hourly consumption by 120%. In terms of burning, synthesis gas has similar properties as natural gas. More significant changes are observed in even burning of fuel in consecutive cycles.

  20. Combustion and Performance Characteristics of CI Engine Running with Biodiesel

    OpenAIRE

    Tesfa, Belachew; Mishra, Rakesh; Gu, Fengshou; Ball, Andrew

    2013-01-01

    Biodiesel is one of the alternative fuels which is renewable and environmentally friendly and can be used in diesel engines with little or no modifications. In the present study, experimental investigations were carried out on the effects of biodiesel types, biodiesel fraction and physical properties on the combustion and performance characteristics of a compression ignition (CI) engine. The experimental work was conducted on a four-cylinder, four -stroke, direct injection (DI) and turbocharg...

  1. A Simplified Model of the Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Christofer Neff

    2013-01-01

    Full Text Available This project further investigates a model of a simplified internal combustion engine considered by Kranc in 1977. Using Euler’s method for ordinary differential equations, we modeled the interaction between the engine’s flywheel and thermodynamic power cycle. Approximating with sufficiently small time intervals (0.001 seconds over a period of 12 seconds reproduced Kranc’s results with the engine having an average angular velocity of 72/sec.

  2. High-Speed Visualisation of Combustion in Modern Gasoline Engines

    Science.gov (United States)

    Sauter, W.; Nauwerck, A.; Han, K.-M.; Pfeil, J.; Velji, A.; Spicher, U.

    2006-07-01

    Today research and development in the field of gasoline engines have to face a double challenge: on the one hand, fuel consumption has to be reduced, while on the other hand, ever more stringent emission standards have to be fulfilled. The development of engines with its complexity of in-cylinder processes requires modern development tools to exploit the full potential in order to reduce fuel consumption. Especially optical, non-intrusive measurement techniques will help to get a better understanding of the processes. With the presented high-speed visualisation system the electromagnetic radiation from combustion in the UV range is collected by an endoscope and transmitted to a visualisation system by 10, 000 optical fibres. The signal is projected to 1, 920 photomultipliers, which convert the optical into electric signals with a maximum temporal resolution of 200 kHz. This paper shows the systematic application of flame diagnostics in modern combustion systems. For this purpose, a single-cylinder SI engine has been modified for a spray guided combustion strategy as well as for HCCI. The characteristics of flame propagation in both combustion modes were recorded and correlated with thermodynamic analyses. In case of the spray guided GDI engine, high pressure fuel injection was applied and evaluated.

  3. COMBUSTION STAGE NUMERICAL ANALYSIS OF A MARINE ENGINE

    Directory of Open Access Journals (Sweden)

    DOREL DUMITRU VELCEA

    2016-06-01

    Full Text Available The primary goal of engine design is to maximize each efficiency factor, in order to extract the most power from the least amount of fuel. In terms of fluid dynamics, the volumetric and combustion efficiency are dependent on the fluid dynamics in the engine manifolds and cylinders. Cold flow analysis involves modeling the airflow in the transient engine cycle without reactions. The goal is to capture the mixture formation process by accurately accounting for the interaction of moving geometry with the fluid dynamics of the induction process. The changing characteristics of the air flow jet that tumbles into the cylinder with swirl via intake valves and the exhaust jet through the exhaust valves as they open and close can be determined, along with the turbulence production from swirl and tumble due to compression and squish. The target of this paper was to show how, by using the reverse engineering techniques, one may replicate and simulate the functioning conditions and parameters of an existing marine engine. The departing information were rather scarce in terms of real processes taking place in the combustion stage, but at the end we managed to have a full picture of the main parameters evolution during the combustion phase inside this existing marine engine

  4. Pocket wheel engine as an internal combustion engine. Taschenscheibenmotor als Verbrennungsmotor

    Energy Technology Data Exchange (ETDEWEB)

    Hellmuth, H.J.

    1990-09-27

    All spark ignition and diesel engines have large oscillating masses, a high frictional resistance and do not run vibration-free. Wankel engines effect only a partial combustion due to the unfavourable shape of the combustion chamber: the expansive force is converted into rotating movement via mechanical deflection. The new internal combustion engine is to have a low weight, require little space and run vibration-free with a high efficiency. The expansive force is to be converted directly into rotating movement. A screw compressor (3) suctions and compresses an air-fuel mixture. The combustion chamber is charged periodically with the compressed mixture via a slit side shaft (6). The slit side shaft (6) closes the combustion chamber (7) at the rear. The mixture is ignited. The flap (8) opens the combustion chamber (7) at the front and the exanding gas sets the pocket wheel connected to the main shaft (15) rotating. The compressor (3) and the slit side shaft (6) are driven directly by the main shaft (15). The pocket wheel engine can be employed in all fields where internal combustion engines have been used until now.

  5. Computational Study of Stratified Combustion in an Optical Diesel Engine

    KAUST Repository

    Jaasim, Mohammed

    2017-03-28

    Full cycle simulations of KAUST optical diesel engine were conducted in order to provide insights into the details of fuel spray, mixing, and combustion characteristics at different start of injection (SOI) conditions. Although optical diagnostics provide valuable information, the high fidelity simulations with matched parametric conditions improve fundamental understanding of relevant physical and chemical processes by accessing additional observables such as the local mixture distribution, intermediate species concentrations, and detailed chemical reaction rates. Commercial software, CONVERGE™, was used as the main simulation tool, with the Reynolds averaged Navier-Stokes (RANS) turbulence model and the multi-zone (SAGE) combustion model to compute the chemical reaction terms. SOI is varied from late compression ignition (CI) to early partially premixed combustion (PPC) conditions. The simulation results revealed a stronger correlation between fuel injection timing and combustion phasing for late SOI conditions, whereas the combustion phasing starts to decouple from SOI for early SOI cases. The predictions are consistent with the experimental observations, in terms of the overall trends in combustion and emission characteristics, while the high fidelity simulations provided further insights into the effects of mixture stratifications resulting from different SOI conditions.

  6. Modelling of fuel spray and combustion in diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Huttunen, M.T.; Kaario, O.T. [VTT Energy, Espoo (Finland)

    1997-12-31

    Fuel spray and air motion characteristics and combustion in direct injection (DI) diesel engines was studied using computational models of the commercial CFD-code FIRE. Physical subprocesses modelled included Lagrangian spray droplet movement and behaviour (atomisation, evaporation and interaction of spray droplets) and combustion of evaporated liquid spray in the gas phase. Fuel vapour combustion rate was described by the model of Magnussen and Hjertager. The standard k,{epsilon}-model was used for turbulence. In order to be able to predict combustion accurately, the fuel spray penetration should be predicted with reasonable accuracy. In this study, the standard drag coefficient had to be reduced in order to match the computed penetration to the measured one. In addition, the constants in the submodel describing droplet breakup also needed to be adjusted for closer agreement with the measurements. The characteristic time scale of fuel consumption rate k/C{sub R} {epsilon} strongly influenced the heat release and in-cylinder pressure. With a value around 2.0 to 5.0 for C{sub R}, the computed in-cylinder pressure during the compression stroke agreed quite well with the measurements. On the other hand, the in-cylinder pressure was underpredicted during the expansion stroke. This is partly due to the fact that hydrocarbon fuel combustion was modelled as a one-step reaction reading to CO{sub 2} and H{sub 2}O and inadequate description of the mixing of reactants and combustion products. (author) 16 refs.

  7. Dynamic model for the internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Rizzoni, G.

    1986-01-01

    Over the last decade there has been increasing interest in the application of control theory to passenger vehicles: stringent governmental regulations constraining fuel consumption and exhaust emissions have required a shift to integrated electronics controls. Unfortunately, the lack of robust global models for the dynamics of the IC engine has limited the application of the tools of control theory in this areas. This dissertation is devoted to the formulation of a robust model for the dynamics of the IC engine. The engine is viewed as a system with inputs given by cylinder pressure and net engine torque, and output corresponding to crankshaft angular acceleration. The model is well suited to closed loop engine and transmission control applications. The deterministic model provides a powerful tool for estimating average and instantaneous net engine torque based on a noncontacting measurement of crankshaft acceleration. The stochastic model explains cyclic pressure variations by an additive Gaussian WSS vector noise process. Further, it demonstrates that by means of a suitable linear transformation-invariant with load and RPM-, the noise process may be expressed in terms of a three-dimensional uncorrelated vector random process.

  8. Using Alcohols as an Alternative Fuel in Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Salih ÖZER

    2014-04-01

    Full Text Available This study summarizes the studies on alcohol use in internal combustion engines nature. Nowadays, alcohol is used in internal combustion engines sometimes in order to reduce emissions and sometimes as an alternative fuel. Even vehicle manufacturers are producing and launching vehicles that are running directly with alcohol. Many types of pure alcohol that can be used on vehicles are available on the world. Using all of these types of alcohol led to the formation of engine emissions and power curves. The studies reveal that these changes are because of the physical and chemical characteristics of alcohols. Thıs study tries to explain what kind of conclusions the physical and chemical properties cause

  9. Introduction to Analytical Methods for Internal Combustion Engine Cam Mechanisms

    CERN Document Server

    Williams, J J

    2013-01-01

    Modern design methods of Automotive Cam Design require the computation of a range of parameters. This book provides a logical sequence of steps for the derivation of the relevant equations from first principles, for the more widely used cam mechanisms. Although originally derived for use in high performance engines, this work is equally applicable to the design of mass produced automotive and other internal combustion engines.   Introduction to Analytical Methods for Internal Combustion Engine Cam Mechanisms provides the equations necessary for the design of cam lift curves with an associated smooth acceleration curve. The equations are derived for the kinematics and kinetics of all the mechanisms considered, together with those for cam curvature and oil entrainment velocity. This permits the cam shape, all loads, and contact stresses to be evaluated, and the relevant tribology to be assessed. The effects of asymmetry on the manufacture of cams for finger follower and offset translating curved followers is ...

  10. Reconstruction of an engine combustion process with a neural network

    Energy Technology Data Exchange (ETDEWEB)

    Jacob, P.J.; Gu, F.; Ball, A.D. [School of Engineering, University of Manchester, Manchester (United Kingdom)

    1997-12-31

    The cylinder pressure waveform in an internal combustion engine is one of the most important parameters in describing the engine combustion process. It is used for a range of diagnostic tasks such as identification of ignition faults or mechanical wear in the cylinders. However, it is very difficult to measure this parameter directly. Never-the-less, the cylinder pressure may be inferred from other more readily obtainable parameters. In this presentation it is shown how a Radial Basis Function network, which may be regarded as a form of neural network, may be used to model the cylinder pressure as a function of the instantaneous crankshaft velocity, recorded with a simple magnetic sensor. The application of the model is demonstrated on a four cylinder DI diesel engine with data from a wide range of speed and load settings. The prediction capabilities of the model once trained are validated against measured data. (orig.) 4 refs.

  11. Co-Optimization of Internal Combustion Engines and Biofuels

    Energy Technology Data Exchange (ETDEWEB)

    McCormick, Robert L.

    2016-03-08

    The development of advanced engines has significant potential advantages in reduced aftertreatment costs for air pollutant emission control, and just as importantly for efficiency improvements and associated greenhouse gas emission reductions. There are significant opportunities to leverage fuel properties to create more optimal engine designs for both advanced spark-ignition and compression-ignition combustion strategies. The fact that biofuel blendstocks offer a potentially low-carbon approach to fuel production, leads to the idea of optimizing the entire fuel production-utilization value chain as a system from the standpoint of life cycle greenhouse gas emissions. This is a difficult challenge that has yet to be realized. This presentation will discuss the relationship between chemical structure and critical fuel properties for more efficient combustion, survey the properties of a range of biofuels that may be produced in the future, and describe the ongoing challenges of fuel-engine co-optimization.

  12. Flow visualization using the laser light sheet method in vehicle aerodynamics and combustion chamber engineering

    Science.gov (United States)

    Hentschel, Werner

    Laser light sheet flow visualization is applied in the automobile industry with a view to the reduction of air resistance. Using high power lasers a plane is cut out of the 3-D flow field and the course of flow in the plane is analyzed. In vehicle aerodynamics the flow phenomena are mainly visualized with smoke in the tail region of automobiles and in the wake, in planes parallel as well as perpendicular to the flow direction. For the investigation of flow phenomena in the combustion chamber of Otto and Diesel engines, the laser light sheet method is used on a series motor with optical access, the so-called flow motor. Typical results and requirements for future automated evaluation methods are discussed.

  13. Laboratory Test of Reciprocating Internal Combustion Engines

    Science.gov (United States)

    2016-02-04

    commercial off the shelf (COTS) or specialized solutions, and pricing . TABLE 1. DYNAMOMETERS: ADVANTAGES AND DISADVANTAGES OF AVAILABLE TYPES...commonly used torque transducers for dynamometer applications can be found at the following link: http://www.hbm.com/en/ menu /products/transducers...www.dieselnet.com/tech/engine_crank.php, 2012. f. HBM Inc., Torque Sensors and Torque Transducers, http://www.hbm.com/en/ menu /products/transducers-sensors

  14. Effects of compression ratio on the combustion characteristics of a homogeneous charge compression ignition engine

    Institute of Scientific and Technical Information of China (English)

    SONG Ruizhi; HU Tiegang; ZHOU Longbao; LIU Shenghua; LI Wei

    2007-01-01

    The effects of homogeneous charge compression ignition (HCCI) engine compression ratio on its combustion characteristics were studied experimentally on a modified TY1100 single cylinder engine fueled with dimethyl ether.The results show that dimethyl ether (DME) HCCI engine can work stably and can realize zero nitrogen oxides (NOx)emission and smokeless combustion under the compression ratio of both 10.7 and 14.The combustion process has obvious two stage combustion characteristics at ε = 10.7(εrefers to compression ratio),and the combustion beginning point is decided by the compression temperature,which varies very little with the engine load;the combustion beginning point is closely related to the engine load (concentration of mixture) with the increase in the compression temperature,and it moves forward versus crank angle with the increase in the engine load at ε = 14;the combustion durations are shortened with the increase in the engine load under both compression ratios.

  15. Stationary Engineers Apprenticeship. Related Training Modules. 16.1-16.5 Combustion.

    Science.gov (United States)

    Lane Community Coll., Eugene, OR.

    This learning module, one in a series of 20 related training modules for apprentice stationary engineers, deals with combustion. Addressed in the individual instructional packages included in the module are the following topics: the combustion process, types of fuel, air and flue gases, heat transfer during combustion, and wood combustion. Each…

  16. Defect Engineering and Interface Phenomena in Tin Oxide

    KAUST Repository

    Albar, Arwa

    2017-04-05

    The advance in transparent electronics requires high-performance transparent conducting oxide materials. The microscopic properties of these materials are sensitive to the presence of defects and interfaces and thus fundamental understanding is required for materials engineering. In this thesis, first principles density functional theory is used to investigate the possibility of tuning the structural, electronic and magnetic properties of tin oxide by means of defects and interfaces. Our aim is to reveal unique properties and the parameters to control them as well as to explain the origin of unique phenomena in oxide materials. The stability of native defect in tin monoxide (SnO) under strain is investigated using formation energy calculations. We find that the conductivity (which is controlled by native defects) can be switched from p-type to either n-type or undoped semiconducting by means of applied pressure. We then target inducing magnetism in SnO by 3d transition metal doping. We propose that V doping is efficient to realize spin polarization at high temperature. We discuss different tin oxide interfaces. Metallic states are found to form at the SnO/SnO2 interface with electronic properties that depend on the interface terminations. The origin of these states is explained in terms of charge transfer caused by chemical bonding and band alignment. For the SnO/SnO2 heterostructure, we observe the formation of a two dimensional hole gas at the interface, which is surprising as it cannot be explained by the standard polar catastrophe model. Thus, we propose a charge density discontinuity model to explain our results. The model can be generalized to other polar-polar interfaces. Motivated by technological applications, the electronic and structural properties of the MgO (100)/SnO2 (110) interface are investigated. Depending on the interface termination, we observe the formation of a two dimensional electron gas or spin polarized hole gas. Aiming to identify further

  17. Method of fabricating a rocket engine combustion chamber

    Science.gov (United States)

    Holmes, Richard R. (Inventor); Mckechnie, Timothy N. (Inventor); Power, Christopher A. (Inventor); Daniel, Ronald L., Jr. (Inventor); Saxelby, Robert M. (Inventor)

    1993-01-01

    A process for making a combustion chamber for a rocket engine wherein a copper alloy in particle form is injected into a stream of heated carrier gas in plasma form which is then projected onto the inner surface of a hollow metal jacket having the configuration of a rocket engine combustion chamber is described. The particles are in the plasma stream for a sufficient length of time to heat the particles to a temperature such that the particles will flatten and adhere to previously deposited particles but will not spatter or vaporize. After a layer is formed, cooling channels are cut in the layer, then the channels are filled with a temporary filler and another layer of particles is deposited.

  18. EXPERIMENTAL INVESTIGATION OF COMBUSTION, PERFORMANCE AND EMISSION CHARACTERISTICS OF DI DIESEL ENGINE UNDER HCCI MODE WITH POROUS MEDIUM COMBUSTION

    OpenAIRE

    Kannan, C.; P TAMILPORAI

    2010-01-01

    In recent times, homogeneous combustion has been a proven technology to attain high efficient and low emission engines. Homogenous Charge Compression Ignition (HCCI) engines are able to have efficiencies as high as Compression Ignition, Direct Injection (CIDI) engines, while producing ultra-low emissions of nitrogen oxides (NOx) and particulate matter (PM).HCCI combustion is achieved by controlling the temperature, pressure and composition of the fuel-air mixture so that it spontaneously gets...

  19. Enhanced efficiency of internal combustion engines by employing spinning gas.

    Science.gov (United States)

    Geyko, V I; Fisch, N J

    2014-08-01

    The efficiency of the internal combustion engine might be enhanced by employing spinning gas. A gas spinning at near sonic velocities has an effectively higher heat capacity, which allows practical fuel cycles, which are far from the Carnot efficiency, to approach more closely the Carnot efficiency. A remarkable gain in fuel efficiency is shown to be theoretically possible for the Otto and Diesel cycles. The use of a flywheel, in principle, could produce even greater increases in efficiency.

  20. Enhanced efficiency of internal combustion engines by employing spinning gas

    Science.gov (United States)

    Geyko, V. I.; Fisch, N. J.

    2014-08-01

    The efficiency of the internal combustion engine might be enhanced by employing spinning gas. A gas spinning at near sonic velocities has an effectively higher heat capacity, which allows practical fuel cycles, which are far from the Carnot efficiency, to approach more closely the Carnot efficiency. A remarkable gain in fuel efficiency is shown to be theoretically possible for the Otto and Diesel cycles. The use of a flywheel, in principle, could produce even greater increases in efficiency.

  1. Influence of intake air temperature on internal combustion engine operation

    Science.gov (United States)

    Birtok-Băneasă, C.; Raţiu, S.; Hepuţ, T.

    2017-01-01

    This paper presents three methods for reduce thermal losses in the intake system with improvement of airflow and thermal protection. In the experiment are involved two patented devices conceived by the author and one PhD theme device: 1- Dynamic device for air transfer, 2-Integrated thermal deflector, and, 3-Advanced thermal protection. The tests were carried on different vehicle running in real traffic and in the Internal Combustion Engines Laboratory, within the specialization “Road vehicle” belonging to the Faculty of Engineering Hunedoara, component of Politehnica University of Timişoara. The results have been processed and compared whit the ones obtained without these devices.

  2. Elimination of abnormal combustion in a hydrogen-fueled engine

    Energy Technology Data Exchange (ETDEWEB)

    Swain, M.R.; Swain, M.N. [Analytical Technologies, Inc., Miami, FL (United States)

    1995-11-01

    This report covers the design, construction, and testing of a dedicated hydrogen-fueled engine. Both part-load and full-load data were taken under laboratory conditions. The engine design included a billet aluminum single combustion chamber cylinder-head with one intake valve, two sodium coiled exhaust valves, and two spark plugs. The cylinder-head design also included drilled cooling passages. The fuel-delivery system employed two modified Siemens electrically actuated fuel injectors, The exhaust system included two separate headers, one for each exhaust port. The piston/ring combination was designed specifically for hydrogen operation.

  3. Flexible fuel engine based on multi-combustion control technologies

    Institute of Scientific and Technical Information of China (English)

    LI Xiaolu; HUANG Zhen; QIAO Xinqi; SONG Jun; FANG Junhua; XIA Huimin

    2005-01-01

    A combustion control strategy is proposed for diesel engine to reduce PM and NOx emissions significantly, which adopts some technologies including internal exhaust gas recirculation (EGR), split spray, adjustable fuel delivery advance angle and the application of alternative fuels. Based on this strategy, a flexible fuel engine has been developed. The experimental results show that this engine can be fueled with diesel fuel, alcohol, dimethyl carbonate (DMC), etc. It works with extremely low levels of particulate matter (PM) and NOx, 2~3% higher effective thermal efficiency on moderate and high loads when alternative fuels are used. This engine not only has lower exhaust emissions, but also can be fueled with those alternative fuels, which are difficult to be ignited by compression.

  4. Turbulence-combustion interaction in direct injection diesel engine

    Directory of Open Access Journals (Sweden)

    Bencherif Mohamed

    2014-01-01

    Full Text Available The experimental measures of chemical species and turbulence intensity during the closed part of the engine combustion cycle are today unattainable exactly. This paper deals with numerical investigations of an experimental direct injection Diesel engine and a commercial turbocharged heavy duty direct injection one. Simulations are carried out with the kiva3v2 code using the RNG (k-ε model. A reduced mechanism for n-heptane was adopted for predicting auto-ignition and combustion processes. From the calibrated code based on experimental in-cylinder pressures, the study focuses on the turbulence parameters and combustion species evolution in the attempt to improve understanding of turbulence-chemistry interaction during the engine cycle. The turbulent kinetic energy and its dissipation rate are taken as representative parameters of turbulence. The results indicate that chemistry reactions of fuel oxidation during the auto-ignition delay improve the turbulence levels. The peak position of turbulent kinetic energy coincides systematically with the auto-ignition timing. This position seems to be governed by the viscous effects generated by the high pressure level reached at the auto-ignition timing. The hot regime flame decreases rapidly the turbulence intensity successively by the viscous effects during the fast premixed combustion and heat transfer during other periods. It is showed that instable species such as CO are due to deficiency of local mixture preparation during the strong decrease of turbulence energy. Also, an attempt to build an innovative relationship between self-ignition and maximum turbulence level is proposed. This work justifies the suggestion to determine otherwise the self-ignition timing.

  5. Dynamic estimator for determining operating conditions in an internal combustion engine

    Science.gov (United States)

    Hellstrom, Erik; Stefanopoulou, Anna; Jiang, Li; Larimore, Jacob

    2016-01-05

    Methods and systems are provided for estimating engine performance information for a combustion cycle of an internal combustion engine. Estimated performance information for a previous combustion cycle is retrieved from memory. The estimated performance information includes an estimated value of at least one engine performance variable. Actuator settings applied to engine actuators are also received. The performance information for the current combustion cycle is then estimated based, at least in part, on the estimated performance information for the previous combustion cycle and the actuator settings applied during the previous combustion cycle. The estimated performance information for the current combustion cycle is then stored to the memory to be used in estimating performance information for a subsequent combustion cycle.

  6. Nitrogen enriched combustion of a natural gas internal combustion engine to reduce NO.sub.x emissions

    Science.gov (United States)

    Biruduganti, Munidhar S.; Gupta, Sreenath Borra; Sekar, R. Raj; McConnell, Steven S.

    2008-11-25

    A method and system for reducing nitrous oxide emissions from an internal combustion engine. An input gas stream of natural gas includes a nitrogen gas enrichment which reduces nitrous oxide emissions. In addition ignition timing for gas combustion is advanced to improve FCE while maintaining lower nitrous oxide emissions.

  7. Virtual Instrument for Emissions Measurement of Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Armando Pérez

    2016-01-01

    Full Text Available The gases emissions measurement systems in internal combustion engines are strict and expensive nowadays. For this reason, a virtual instrument was developed to measure the combustion emissions from an internal combustion diesel engine, running with diesel-biodiesel mixtures. This software is called virtual instrument for emissions measurement (VIEM, and it was developed in the platform of LabVIEW 2010® virtual programming. VIEM works with sensors connected to a signal conditioning system, and a data acquisition system is used as interface for a computer in order to measure and monitor in real time the emissions of O2, NO, CO, SO2, and CO2 gases. This paper shows the results of the VIEM programming, the integrated circuits diagrams used for the signal conditioning of sensors, and the sensors characterization of O2, NO, CO, SO2, and CO2. VIEM is a low-cost instrument and is simple and easy to use. Besides, it is scalable, making it flexible and defined by the user.

  8. Virtual Instrument for Emissions Measurement of Internal Combustion Engines

    Science.gov (United States)

    Pérez, Armando; Montero, Gisela; Coronado, Marcos; García, Conrado; Pérez, Rubén

    2016-01-01

    The gases emissions measurement systems in internal combustion engines are strict and expensive nowadays. For this reason, a virtual instrument was developed to measure the combustion emissions from an internal combustion diesel engine, running with diesel-biodiesel mixtures. This software is called virtual instrument for emissions measurement (VIEM), and it was developed in the platform of LabVIEW 2010® virtual programming. VIEM works with sensors connected to a signal conditioning system, and a data acquisition system is used as interface for a computer in order to measure and monitor in real time the emissions of O2, NO, CO, SO2, and CO2 gases. This paper shows the results of the VIEM programming, the integrated circuits diagrams used for the signal conditioning of sensors, and the sensors characterization of O2, NO, CO, SO2, and CO2. VIEM is a low-cost instrument and is simple and easy to use. Besides, it is scalable, making it flexible and defined by the user. PMID:27034893

  9. Liquid butane fuel injection for internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Kaufman, R.L.; Brunges, V.E.; Bisel, H.I.

    1991-07-30

    This patent describes an internal combustion engine powered by a fuel of liquefied petroleum gas. It comprises at least one cylinder head which includes an intake port region communicating with a combustion chamber through an intake valve; a fuel injection rail including at least one fuel injector, all injectors operably connected to all intake port regions with one intake region connected to one injector whereby fuel may be injected into the intake regions; a conduit connecting the container to the injection rail; means for pumping the fuel from the injection rail and maintaining the fuel at a temperature below a temperature value and pressure above a pressure value required to sustain the fuel in a liquid state whereby the fuel in the liquid state is transferred from the storage container to the rail.

  10. Control using intake and combustion models for conventional and active radical engines

    Energy Technology Data Exchange (ETDEWEB)

    Ohyama, Y. [Hitachi Car Engineering Co. Ltd., Hitachinaka (Japan)

    2000-07-01

    The combination of physical models of an advanced engine control system was proposed to obtain sophisticated combustion control in ultra-lean combustion engines, including homogeneous compression-ignition and active radical combustion. Physical models of intake, combustion and engine thermodynamics were incorporated, in which the effects of residual gas from prior cycles on intake air mass and combustion were taken into consideration. The control of in-cylinder air/fuel ratio, misfire, knocking and auto-ignition was investigated using simulations. (author)

  11. Engine modeling and control modeling and electronic management of internal combustion engines

    CERN Document Server

    Isermann, Rolf

    2014-01-01

    The increasing demands for internal combustion engines with regard to fuel consumption, emissions and driveability lead to more actuators, sensors and complex control functions. A systematic implementation of the electronic control systems requires mathematical models from basic design through simulation to calibration. The book treats physically-based as well as models based experimentally on test benches for gasoline (spark ignition) and diesel (compression ignition) engines and uses them for the design of the different control functions. The main topics are: - Development steps for engine control - Stationary and dynamic experimental modeling - Physical models of intake, combustion, mechanical system, turbocharger, exhaust, cooling, lubrication, drive train - Engine control structures, hardware, software, actuators, sensors, fuel supply, injection system, camshaft - Engine control methods, static and dynamic feedforward and feedback control, calibration and optimization, HiL, RCP, control software developm...

  12. Mixer for internal combustion engines. Gemischbildner fuer Brennkraftmaschinen

    Energy Technology Data Exchange (ETDEWEB)

    Haertel, G.; Schiele, W.; Schuerfeld, A.; Bianchi, V.; Abidin, A.

    1981-06-11

    The invention concerns a mixer for internal combustion engines with a pipe wall limiting the main flow path and heated for part of its length and with a throttle upstream and a fuel allocation device in the upstream part of a mixing chamber inside the pipe wall. The invention is characterised by the fact that the pipe wall surrounding the mixing chamber is made as a heating wall from the fuel allocation device to the throttle and the fuel allocation device guides the fuel to the heating wall. The heating wall is made as a double wall of a heat exchanger to guide the liquid or gaseous heating medium, such as engine cooling water or engine exhaust gas. The heating wall consists of an electrical resistance heating material on the inside. Other measures of the invention are described by system drawings and 33 patent claims.

  13. Plasma Assisted Combustion: Fundamental Studies and Engine Applications

    Science.gov (United States)

    Lefkowitz, Joseph K.

    Successful and efficient ignition in short residence time environments or ultra-lean mixtures is a key technological challenge for the evolution of advanced combustion devices in terms of both performance and efficiency. To meet this challenge, interest in plasma assisted combustion (PAC) has expanded over the past 20 years. However, understanding of the underlying physical processes of ignition by plasma discharge remains elementary. In order to shed light on the key processes involved, two main thrusts of research were undertaken in this dissertation. First, demonstration of the applicability of plasma discharges in engines and engine-like environments was carried out using a microwave discharge and a nanosecond repetitively pulsed discharge in an internal combustion engine and a pulsed detonation engine, respectively. Major conclusions include the extension of lean ignition limits for both engines, significant reduction of ignition time for mixtures with large minimum ignition energy, and the discovery of the inter-pulse coupling effect of nanosecond repetitively pulsed (NRP) discharges at high frequency. In order to understand the kinetic processes that led to these improvements, the second thrust of research directly explored the chemical kinetic processes of plasma discharges with hydrocarbon fuels. For this purpose, a low pressure flow reactor with a NRP dielectric barrier discharge cell was assembled. The discharge cell was fitted with a Herriott type multipass mirror arrangement, which allowed quantitative laser absorption spectroscopy to be performed in situ during the plasma discharge. Experiments on methane and ethylene mixtures with oxygen, argon, and helium revealed the importance of low temperature oxidation pathways in PAC. In particular, oxygen addition reactions were shown to be of primary importance in the oxidation of these small hydrocarbons in the temperature range of 300-600 K. Kinetic modeling tools, including both a coupled plasma and

  14. Effect of Gas Mixture Composition on the Parameters of an Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Andrej Chríbik

    2012-01-01

    Full Text Available This paper deals with the use of the internal combustion piston engine, which is a drive unit for micro-cogeneration units. The introduction is a brief statement of the nature of gas mixture compositions that are useful for the purposes of combustion engines, together with the basic physical and chemical properties relevant to the burning of this gas mixture. Specifically, we will discuss low-energy gases (syngases and mixtures of natural gas with hydrogen. The second section describes the conversion of the Lombardini LGW 702 combustion engine that is necessary for these types of combustion gases. Before the experimental measurements, a simulation in the Lotus Engine simulation program was carried out to make a preliminary assessment of the impact on the performance of an internal combustion engine. The last section of the paper presents the experimental results of partial measurements of the performance and emission parameters of an internal combustion engine powered by alternative fuels.

  15. Internal combustion engines a detailed introduction to the thermodynamics of spark and compression ignition engines, their design and development

    CERN Document Server

    Benson, Rowland S

    1979-01-01

    Internal Combustion of Engines: A Detailed Introduction to the Thermodynamics of Spark and Compression Ignition Engines, Their Design and Development focuses on the design, development, and operations of spark and compression ignition engines. The book first describes internal combustion engines, including rotary, compression, and indirect or spark ignition engines. The publication then discusses basic thermodynamics and gas dynamics. Topics include first and second laws of thermodynamics; internal energy and enthalpy diagrams; gas mixtures and homocentric flow; and state equation. The text ta

  16. 46 CFR 62.35-35 - Starting systems for internal-combustion engines.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Starting systems for internal-combustion engines. 62.35-35 Section 62.35-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE... Starting systems for internal-combustion engines. The starting systems for propulsion engines and for prime...

  17. Numerical investigation of combustion field of hypervelocity scramjet engine

    Science.gov (United States)

    Zhang, Shikong; Li, Jiang; Qin, Fei; Huang, Zhiwei; Xue, Rui

    2016-12-01

    A numerical study of the ground testing of a hydrogen-fueled scramjet engine was undertaken using the commercial computational-fluid-dynamics code CFD++. The simulated Mach number was 12. A 7-species, 9-reaction-step hydrogen-air chemistry kinetics system was adopted for the Reynolds-averaged Navier-Stokes simulation. The two-equation SST turbulence model, which takes into account the wall functions, was used to handle the turbulence-chemistry interactions. The results were validated by experimentally measuring the wall pressure distribution, and the values obtained proved to be in good agreement. The flow pattern at non-reaction/reaction is presented, as are the results of analyzing the supersonic premix/non-premix flame structure, the reaction heat release distribution in different modes, and the change in the equivalence ratio. In this study, we realize the working mode of a hypervelocity engine and provide some suggestions for the combustion organization of the engine as well as offer insight into the potential for exploiting the processes of combustion and flow.

  18. Development and Validation of a Reduced DME Mechanism Applicable to Various Combustion Modes in Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Gregory T. Chin

    2011-01-01

    Full Text Available A 28-species reduced chemistry mechanism for Dimethyl Ether (DME combustion is developed on the basis of a recent detailed mechanism by Zhao et al. (2008. The construction of reduced chemistry was carried out with automatic algorithms incorporating newly developed strategies. The performance of the reduced mechanism is assessed over a wide range of combustion conditions anticipated to occur in future advanced piston internal combustion engines, such as HCCI, SAHCCI, and PCCI. Overall, the reduced chemistry gives results in good agreement with those from the detailed mechanism for all the combustion modes tested. While the detailed mechanism by Zhao et al. (2008 shows reasonable agreement with the shock tube autoignition delay data, the detailed mechanism requires further improvement in order to better predict HCCI combustion under engine conditions.

  19. Use of the graphical analytic methods of studying the combustion processes in the internal combustion engine combustion chamber on the basis of similarity criterion

    Directory of Open Access Journals (Sweden)

    S. V. Krasheninnikov

    2014-10-01

    Full Text Available The task of improving the economic and ecological parameters of the internal combustion engines remains topical within the frameworks of the modern engine-building technology. Since a combustion engine is a complex system combining such units as an intake manifold, combustion chamber, exhaust manifold, one of directions of the engine development is adjustment of the joint operation of its units. The specified adjustment should better be performed with the use of the so-called integral characteristics. The author means under an integral characteristic the rating plate of a unit (engine containing information about all the possible modes and conditions of its use, specifies the optimal operating range and indicates all the basic values of efficiency – reliability – environmental friendliness at each point of its field. As a rule, integral characteristics are multi-parametric. It is common practice to coordinate the field of such characteristic by similarity criteria determining the unit or engine behavior in whole.

  20. Mathematical Model of Piston Ring Sealing in Combustion Engine

    Directory of Open Access Journals (Sweden)

    Koszałka Grzegorz

    2015-01-01

    Full Text Available This paper presents a mathematical model of piston-rings-cylinder sealing (TPC of a combustion engine. The developed model is an itegrated model of gas flow through gaps in TPC unit, displacements and twisting motions of piston rings in ring grooves as well as generation of oil film between ring face surfaces and cylinder liner. Thermal deformations and wear of TPC unit elements as well as heat exchange between flowing gas and surrounding walls, were taken into account in the model. The paper contains descriptions of: assumptions used for developing the model, the model itself, its numerical solution as well as its computer application for carrying out simulation tests.

  1. Mathematical Model of Piston Ring Sealing in Combustion Engine

    OpenAIRE

    Koszałka Grzegorz; Guzik Mirosław

    2015-01-01

    This paper presents a mathematical model of piston-rings-cylinder sealing (TPC) of a combustion engine. The developed model is an itegrated model of gas flow through gaps in TPC unit, displacements and twisting motions of piston rings in ring grooves as well as generation of oil film between ring face surfaces and cylinder liner. Thermal deformations and wear of TPC unit elements as well as heat exchange between flowing gas and surrounding walls, were taken into account in the model. The pape...

  2. Identification and quantification analysis of nonlinear dynamics properties of combustion instability in a diesel engine

    Science.gov (United States)

    Yang, Li-Ping; Ding, Shun-Liang; Litak, Grzegorz; Song, En-Zhe; Ma, Xiu-Zhen

    2015-01-01

    The cycling combustion instabilities in a diesel engine have been analyzed based on chaos theory. The objective was to investigate the dynamical characteristics of combustion in diesel engine. In this study, experiments were performed under the entire operating range of a diesel engine (the engine speed was changed from 600 to 1400 rpm and the engine load rate was from 0% to 100%), and acquired real-time series of in-cylinder combustion pressure using a piezoelectric transducer installed on the cylinder head. Several methods were applied to identify and quantitatively analyze the combustion process complexity in the diesel engine including delay-coordinate embedding, recurrence plot (RP), Recurrence Quantification Analysis, correlation dimension (CD), and the largest Lyapunov exponent (LLE) estimation. The results show that the combustion process exhibits some determinism. If LLE is positive, then the combustion system has a fractal dimension and CD is no more than 1.6 and within the diesel engine operating range. We have concluded that the combustion system of diesel engine is a low-dimensional chaotic system and the maximum values of CD and LLE occur at the lowest engine speed and load. This means that combustion system is more complex and sensitive to initial conditions and that poor combustion quality leads to the decrease of fuel economy and the increase of exhaust emissions.

  3. Identification and quantification analysis of nonlinear dynamics properties of combustion instability in a diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Li-Ping, E-mail: yangliping302@hrbeu.edu.cn; Ding, Shun-Liang; Song, En-Zhe; Ma, Xiu-Zhen [Institute of Power and Energy Engineering, Harbin Engineering University, No. 145-1, Nantong Street, Nangang District, Harbin 150001 (China); Litak, Grzegorz [Faculty of Mechanical Engineering, Lublin University of Technology, Nadbystrzycka 36, 20-618 Lublin (Poland)

    2015-01-15

    The cycling combustion instabilities in a diesel engine have been analyzed based on chaos theory. The objective was to investigate the dynamical characteristics of combustion in diesel engine. In this study, experiments were performed under the entire operating range of a diesel engine (the engine speed was changed from 600 to 1400 rpm and the engine load rate was from 0% to 100%), and acquired real-time series of in-cylinder combustion pressure using a piezoelectric transducer installed on the cylinder head. Several methods were applied to identify and quantitatively analyze the combustion process complexity in the diesel engine including delay-coordinate embedding, recurrence plot (RP), Recurrence Quantification Analysis, correlation dimension (CD), and the largest Lyapunov exponent (LLE) estimation. The results show that the combustion process exhibits some determinism. If LLE is positive, then the combustion system has a fractal dimension and CD is no more than 1.6 and within the diesel engine operating range. We have concluded that the combustion system of diesel engine is a low-dimensional chaotic system and the maximum values of CD and LLE occur at the lowest engine speed and load. This means that combustion system is more complex and sensitive to initial conditions and that poor combustion quality leads to the decrease of fuel economy and the increase of exhaust emissions.

  4. Identification and quantification analysis of nonlinear dynamics properties of combustion instability in a diesel engine.

    Science.gov (United States)

    Yang, Li-Ping; Ding, Shun-Liang; Litak, Grzegorz; Song, En-Zhe; Ma, Xiu-Zhen

    2015-01-01

    The cycling combustion instabilities in a diesel engine have been analyzed based on chaos theory. The objective was to investigate the dynamical characteristics of combustion in diesel engine. In this study, experiments were performed under the entire operating range of a diesel engine (the engine speed was changed from 600 to 1400 rpm and the engine load rate was from 0% to 100%), and acquired real-time series of in-cylinder combustion pressure using a piezoelectric transducer installed on the cylinder head. Several methods were applied to identify and quantitatively analyze the combustion process complexity in the diesel engine including delay-coordinate embedding, recurrence plot (RP), Recurrence Quantification Analysis, correlation dimension (CD), and the largest Lyapunov exponent (LLE) estimation. The results show that the combustion process exhibits some determinism. If LLE is positive, then the combustion system has a fractal dimension and CD is no more than 1.6 and within the diesel engine operating range. We have concluded that the combustion system of diesel engine is a low-dimensional chaotic system and the maximum values of CD and LLE occur at the lowest engine speed and load. This means that combustion system is more complex and sensitive to initial conditions and that poor combustion quality leads to the decrease of fuel economy and the increase of exhaust emissions.

  5. Investigations of Rocket Engine Combustion Emissions During ACCENT

    Science.gov (United States)

    Ross, M. N.; Friedl, R. R.

    2001-12-01

    The composition of rocket combustion emissions and the atmospheric processes that determine their stratospheric impacts are poorly understood. While present day rocket emissions do not significantly affect stratospheric chemistry, the potential for vigorous growth of the space transportation industry in coming decades suggests that rocket emissions and their stratospheric impacts should be better understood. A variety of in-situ measurements and modeling results were obtained during the Atmospheric Chemistry of Combustion Emissions Near the Tropopause (ACCENT) effort that will be used to evaluate the role of rocket exhaust in perturbing ozone chemistry in plume wakes and in the global stratosphere. We present a review of the ACCENT rocket emissions science objectives, summarize data obtained during the WB-57F plume wake sorties, and briefly discuss how the data will help resolve several outstanding questions regarding the impact of rocket emissions on the stratosphere. These include measurement of the emission indices for several important rocket engine combustion products and validation of plume wake chemistry models.

  6. Transport phenomena in biomedical engineering principles and practices

    CERN Document Server

    Peattie, Robert A; Bronzino, Joseph D

    2012-01-01

    Biomimetic Systems: Concepts, Design, and Emulation, Robert J. FisherTransport/Reaction Processes in Biology and Medicine, E. N. LightfootMicrovascular Heat Transfer, James W. BaishFluid Dynamics for Bio Systems: Fundamentals and Model Analysis, Robert A. Peattie and Robert J. FisherAnimal Surrogate Systems, Michael L. Shuler, Sarina G. Harris, Xinran Li, and Mandy B. EschArterial Wall Mass Transport: The Possible Role of Blood Phase Resistance in the Localization of Arterial Disease, John M. Tarbell and Yuchen QiuTransport Phenomena and the Microenvironment, Robert J. Fisher and Robert A. PeattieTransport and Drug Delivery through the Blood-Brain Barrier and Cerebrospinal Fluid, Bingmei M. FuInterstitial Transport in the Brain: Principles for Local Drug Delivery, W. Mark SaltzmanSurfactant Transport and Fluid-Structure Interactions during Pulmonary Airway Reopening, David Martin, Anne-Marie Jacob, and Donald P. Gaver IIIIndex.

  7. Study of Second Generation Biofuels in Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Kannan, Dhandapani

    2012-07-01

    fuel, vis-a-vis neat diesel fuel (DF). The CO, THC, smoke and TPM emissions were reduced significantly, while NOx emissions were somewhat higher with BD blended fuels compared to neat FT fuel. The reductions in CO, THC, smoke and TPM emissions with BD blends were mainly due to the oxygen content in the BD blended fuel, while the increases in NOx emissions with BD fuels were due to advances in injection timing, higher percentages of fatty acids with double bonds in the carbon chain and higher heat release in the pre-mixed combustion. Secondly, a four-stroke, single-cylinder, naturally-aspirated (NA), direct-injection (DI) diesel engine with 8 BHP at 1500 rpm coupled with water-cooled, eddy current dynamometer was used for the experiments. Ethanol (5% by volume) was injected into the intake manifold by the port injection method with the assistance of a mechanical fuel injection pump. Therefore, the volumetric blending percentages of ethanol, BD and diesel fuels (E:D:JME) are (0:100:0), (5:95:0), (5:75:20), (5:55:40), (5:35:60), (5:15:80) (5:0:95) and (0:0:100) respectively. Ethanol pre-mixed with intake air, assisted in improving combustion in both diesel and the JME blends. The addition of ethanol to high-viscosity Jatropha methyl ester (JME) through port injection is investigated in order to determine its effect on the fuels viscosity and thereby on the diesel engine performance. In addition to viscosity alteration, the impact of ethanol addition on combustion characteristics such as combustion duration, ignition delay and emissions levels from diesel engines fuelled with blends of ethanol, diesel and JME was studied in particular. It was found that blending of oxygenated fuels with diesel modifies the chemical structure and physical properties which in turn, alter the engines operating conditions, combustion parameters and emissions levels. However, the injection of only 5% ethanol through port injection allows for up to 25% blending of diesel with biofuels, while

  8. A new predictive multi-zone model for HCCI engine combustion

    Energy Technology Data Exchange (ETDEWEB)

    Bissoli, M.; Frassoldati, A.; Cuoci, A.; Ranzi, E.; Mehl, M.; Faravelli, T.

    2016-09-01

    This work introduces a new predictive multi-zone model for the description of combustion in Homogeneous Charge Compression Ignition (HCCI) engines. The model exploits the existing OpenSMOKE++ computational suite to handle detailed kinetic mechanisms, providing reliable predictions of the in-cylinder auto-ignition processes. All the elements with a significant impact on the combustion performances and emissions, like turbulence, heat and mass exchanges, crevices, residual burned gases, thermal and feed stratification are taken into account. Compared to other computational approaches, this model improves the description of mixture stratification phenomena by coupling a wall heat transfer model derived from CFD application with a proper turbulence model. Furthermore, the calibration of this multi-zone model requires only three parameters, which can be derived from a non-reactive CFD simulation: these adaptive variables depend only on the engine geometry and remain fixed across a wide range of operating conditions, allowing the prediction of auto-ignition, pressure traces and pollutants. This computational framework enables the use of detail kinetic mechanisms, as well as Rate of Production Analysis (RoPA) and Sensitivity Analysis (SA) to investigate the complex chemistry involved in the auto-ignition and the pollutants formation processes. In the final sections of the paper, these capabilities are demonstrated through the comparison with experimental data.

  9. The history and evolution of optically accessible research engines and their impact on our understanding of engine combustion

    Energy Technology Data Exchange (ETDEWEB)

    Miles, Paul C. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-03-01

    The development and application of optically accessible engines to further our understanding of in-cylinder combustion processes is reviewed, spanning early efforts in simplified engines to the more recent development of high-pressure, high-speed engines that retain the geometric complexities of modern production engines. Limitations of these engines with respect to the reproduction of realistic metal test engine characteristics and performance are identified, as well as methods that have been used to overcome these limitations. Finally, the role of the work performed in these engines on clarifying the fundamental physical processes governing the combustion process and on laying the foundation for predictive engine simulation is summarized.

  10. Internal combustion engine for natural gas compressor operation

    Energy Technology Data Exchange (ETDEWEB)

    Hagen, Christopher L.; Babbitt, Guy; Turner, Christopher; Echter, Nick; Weyer-Geigel, Kristina

    2016-04-19

    This application concerns systems and methods for compressing natural gas with an internal combustion engine. In a representative embodiment, a system for compressing a gas comprises a reciprocating internal combustion engine including at least one piston-cylinder assembly comprising a piston configured to travel in a cylinder and to compress gas in the cylinder in multiple compression stages. The system can further comprise a first pressure tank in fluid communication with the piston-cylinder assembly to receive compressed gas from the piston-cylinder assembly until the first pressure tank reaches a predetermined pressure, and a second pressure tank in fluid communication with the piston-cylinder assembly and the first pressure tank. The second pressure tank can be configured to receive compressed gas from the piston-cylinder assembly until the second pressure tank reaches a predetermined pressure. When the first and second pressure tanks have reached the predetermined pressures, the first pressure tank can be configured to supply gas to the piston-cylinder assembly, and the piston can be configured to compress the gas supplied by the first pressure tank such that the compressed gas flows into the second pressure tank.

  11. Internal combustion engine for natural gas compressor operation

    Science.gov (United States)

    Hagen, Christopher L.; Babbitt, Guy; Turner, Christopher; Echter, Nick; Weyer-Geigel, Kristina

    2016-04-19

    This application concerns systems and methods for compressing natural gas with an internal combustion engine. In a representative embodiment, a system for compressing a gas comprises a reciprocating internal combustion engine including at least one piston-cylinder assembly comprising a piston configured to travel in a cylinder and to compress gas in the cylinder in multiple compression stages. The system can further comprise a first pressure tank in fluid communication with the piston-cylinder assembly to receive compressed gas from the piston-cylinder assembly until the first pressure tank reaches a predetermined pressure, and a second pressure tank in fluid communication with the piston-cylinder assembly and the first pressure tank. The second pressure tank can be configured to receive compressed gas from the piston-cylinder assembly until the second pressure tank reaches a predetermined pressure. When the first and second pressure tanks have reached the predetermined pressures, the first pressure tank can be configured to supply gas to the piston-cylinder assembly, and the piston can be configured to compress the gas supplied by the first pressure tank such that the compressed gas flows into the second pressure tank.

  12. THE COMBUSTION ACTION VERIFICATION AND ESTIMATE OF COMBUSTION EFFICIENCY IN AVIATION GAS#TURBINE ENGINE COMBUSTION CHAMBERS

    OpenAIRE

    2011-01-01

    Verification results of combustion action simulating and estimate of calculation combustion efficiency that was given by simulating were shown. Mathematical model and its assumption are described. Execution calculations method was shown. Results of simulating are shown; their comparative analyses with results of experiment were executed. Accuracy of combustion action mathematical modeling by combustion efficiency in model with oneand two-stage reactions of combustion was estimated. The infere...

  13. Coal slurry combustion optimization on single cylinder engine. Task 1.1.2.2.2, Combustion R&D

    Energy Technology Data Exchange (ETDEWEB)

    1992-09-01

    Under the sponsorship of the US Department of Energy, Morgantown Energy Technology Center, GE Transportation System has been conducting a proof of concept program to use coal water slurry (CWS) fuel to power a diesel engine locomotive since 1988. As reported earlier [1], a high pressure electronically controlled accumulator injector using a diamond compact insert nozzle was developed for this project. The improved reliability and durability of this new FIE allowed for an improved and more thorough study of combustion of CWS fuel in a diesel engine. It was decided to include a diesel pilot fuel injector in the combustion system mainly due to engine start and low load operation needs. BKM, Inc. of San Diego, CA was contracted to develop the electronic diesel fuel pilot/starting FIE for the research engine. As a result, the experimental combustion study was very much facilitated due to the ability of changing pilot/CWS injection timings and quantities without having to stop the engine. Other parameters studied included combustion chamber configuration (by changing CWS fuel injector nozzle hole number/shape/angle), as well as injection pressure. The initial phase of this combustion study is now complete. The results have been adopted into the design of a 12 cylinder engine FIE, to be tested in 1992. This paper summarizes the main findings of this study.

  14. Optical Engines as Representative Tools in the Development of New Combustion Engine Concepts Moteurs transparents comme outils représentatifs dans le développement de nouveaux concepts des moteurs à combustion interne

    Directory of Open Access Journals (Sweden)

    Kashdan J.

    2011-11-01

    Full Text Available Single cylinder optical engines are used for Internal Combustion (IC engine research as they allow for the application of qualitative and quantitative non-intrusive, diagnostic techniques to study in-cylinder flow, mixing, combustion and emissions phenomena. Such experimental data is not only important for the validation of computational models but can also provide a detailed insight into the physical processes occurring in-cylinder which is useful for the further development of new combustion strategies such as gasoline Homogeneous Charge Compression Ignition (HCCI and Diesel Low Temperature Combustion (LTC. In this context, it is therefore important to ensure that the performance of optical engines is comparable to standard all-metal engines. A comparison of optical and all-metal engine combustion and emissions performance was performed within the present study. The objective was to investigate the principal differences between optical and all-metal engines and understand how these differences ultimately affect mixing, combustion and emissions formation processes. Experimental results reveal the significant impact of differences in combustion chamber wall temperatures between optical and standard engine piston bowls on combustion phasing and engine-out emissions. Quantitative measurements of piston wall temperatures using a laser-induced phosphorescence technique were performed which allowed the subsequent definition of appropriate engine operating strategies so as to compensate for differences in heat transfer properties. Furthermore, differences in combustion chamber geometry were also studied. Geometrical differences can arise as a result of dynamic (compressive/tensile and thermal loading of the extended piston-liner assembly on the optical engine, potentially leading to changes in the effective Compression Ratio. In addition, intake charge dilution in optical engines is often achieved via the use of simulated Exhaust Gas Recirculation

  15. EMISSION AND COMBUSTION CHARACTERISTICS OF DIFFERENT FUELS IN A HCCI ENGINE

    Directory of Open Access Journals (Sweden)

    S. Sendilvelan

    2011-06-01

    Full Text Available Different intake valve timings and fuel injection amounts were tested in order to identify their effects on exhaust emissions and combustion characteristics using variable valve actuation (VVA in a Homogeneous Charge Compression Ignition (HCCI engine. The HCCI engine is a promising concept for future automobile engines and stationary power plants. The two-stage ignition process in a HCCI engine creates advanced ignition and stratified combustion, which makes the ignition timing and combustion rate controllable. Meanwhile, the periphery of the fuel-rich zone leads to fierce burning, which results in slightly high NOx emissions. The experiments were conducted in a modified single cylinder water-cooled diesel engine. In this experiment we use diesel, bio-diesel (Jatropha and gasoline as the fuel at different mixing ratios. HCCI has advantages in high thermal efficiency and low emissions and could possibly become a promising combustion method in internal combustion engines.

  16. Orthogonal polarization in lasers physical phenomena and engineering applications

    CERN Document Server

    Zhang, Shulian

    2013-01-01

    This practical book summarizes the latest research results of orthogonally polarized lasers, birefringence laser cavities, and their applications. Coverage ranges from basic principles and technologies to the characteristics of different cavities and lasers to various measurement techniques. A number of figures, experimental designs, and measurement curves are included, helping readers gain a thorough understanding of the many applications in modern engineering and start their own projects. Many types of relevant lasers (Helium/Neon lasers, Nd:YAG lasers, laser diodes, etc.) are also discussed

  17. Combustion engine diagnosis model-based condition monitoring of gasoline and diesel engines and their components

    CERN Document Server

    Isermann, Rolf

    2017-01-01

    This book offers first a short introduction to advanced supervision, fault detection and diagnosis methods. It then describes model-based methods of fault detection and diagnosis for the main components of gasoline and diesel engines, such as the intake system, fuel supply, fuel injection, combustion process, turbocharger, exhaust system and exhaust gas aftertreatment. Additionally, model-based fault diagnosis of electrical motors, electric, pneumatic and hydraulic actuators and fault-tolerant systems is treated. In general series production sensors are used. It includes abundant experimental results showing the detection and diagnosis quality of implemented faults. Written for automotive engineers in practice, it is also of interest to graduate students of mechanical and electrical engineering and computer science. The Content Introduction.- I SUPERVISION, FAULT DETECTION AND DIAGNOSIS METHODS.- Supervision, Fault-Detection and Fault-Diagnosis Methods - a short Introduction.- II DIAGNOSIS OF INTERNAL COMBUST...

  18. Concept for lowest emissions of a hydrogen internal combustion engine; Niedrigstemissionskonzept fuer einen wasserstoffbetriebenen Verbrennungsmotor

    Energy Technology Data Exchange (ETDEWEB)

    Fouquet, Marcel Christian Thomas

    2012-03-15

    This paper describes a concept with lowest emissions for a hydrogen internal combustion engine for passenger cars. With optimisation of the combustion concept the level of nitrogen oxide is below 90%, hydrocarbon and carbon monoxide below 99% of the SULEV target (CARB). This concept enables a potential in power density that is comparable to current supercharged combustion engines at lowest emission level without catalytic aftertreatment. Additionally with a catalytic aftertreatment system, the emission level of a current hydrogen combustion engine (mono-fuel) is lowered to a level, that this car can be labeled as air cleaning vehicle for hydrocarbons and carbon monoxide.

  19. OPTIMUM PLANNING OF EXPERIMENTS AT MODELING FUEL CONSUMPTION IN INTERNAL COMBUSTION ENGINES

    Directory of Open Access Journals (Sweden)

    N. Koshevoy

    2009-01-01

    Full Text Available The efficiency of optimum experiments planning by cost expenses at studying the processes of fuel consumption internal combustion engines is shown. The mathematical models of these processes in different state of engine working are synthesized.

  20. Recurrence plot for parameters analysing of internal combustion engine

    Science.gov (United States)

    Alexa, O.; Ilie, C. O.; Marinescu, M.; Vilau, R.; Grosu, D.

    2015-11-01

    In many technical disciplines modem data analysis techniques has been successfully applied to understand the complexity of the system. The growing volume of theoretical knowledge about systems dynamic's offered researchers the opportunity to look for non-linear dynamics in data whose evolution linear models are unable to explain in a satisfactory manner. One approach in this respect is Recurrence Analysis - RA which is a graphical method designed to locate hidden recurring patterns, nonstationarity and structural changes. RA approach arose in natural sciences like physics and biology but quickly was adopted in economics and engineering. Meanwhile. The fast development of computer resources has provided powerful tools to perform this new and complex model. One free software which was used to perform our analysis is Visual Recurrence Analysis - VRA developed by Eugene Kononov. As is presented in this paper, the recurrence plot investigation for the analyzing of the internal combustion engine shows some of the RPA capabilities in this domain. We chose two specific engine parameters measured in two different tests to perform the RPA. These parameters are injection impulse width and engine angular speed and the tests are I11n and I51n. There were computed graphs for each of them. Graphs were analyzed and compared to obtain a conclusion. This work is an incipient research, being one of the first attempts of using recurrence plot for analyzing automotive dynamics. It opens a wide field of action for future research programs.

  1. Combustion instability investigations on the BR710 jet engine

    Energy Technology Data Exchange (ETDEWEB)

    Konrad, W.; Brehm, N.; Kameier, F. [BMW Rolls-Royce AeroEngines, Dahlewitz (Germany); Freeman, C. [Rolls-Royce PLC, Derby (United Kingdom). Advanced Propulsion Systems; Day, I.J. [Cambridge Univ. (United Kingdom). Whittle Lab.

    1998-01-01

    During the development of the BR710 jet engine, audible combustor instabilities (termed rumble) occurred. Amplitudes measured with test cell microphones were up to 130 dB at around 100 Hz. Disturbances of this amplitude are clearly undesirable, even if only present during start-up, and a research program was initiated to eliminate the problem. Presented here is the methodical and structured approach used to identify, understand, and remove the instability. Some reference is made to theory, which was used for guidance, but the focus of the work is on the research done to find the cause of the problem and to correct it. The investigation followed two separate, but parallel, paths--one looking in detail at individual components of the engine to identify possible involvement in the instability and the other looking at the pressure signals from various parts of a complete engine to help pinpoint the source of the disturbance. The main cause of the BR710 combustor rumble was found to be a self-excited aerodynamic instability arising from the design of the fuel injector head. In the end, minor modifications lead to spray pattern changes, which greatly reduced the combustor noise. As a result of this work, new recommendation are made for reducing the risk of combustion instabilities in jet engines.

  2. Implications of combustion parameters on the performance of a hydrogen-fuelled research engine

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, G.N.; Subash, G.P.; Das, L.M. [IIT, Delhi, New Delhi (India). Centre for Energy Studies

    2010-07-01

    This paper highlights part of the continuing R and D activities being carried out in the Engines and Unconventional Fuel Laboratory of Indian Institute of Technology for several years. Several engine configurations have been built up and widely tested to generate optimum performance and low-emission characteristics without any symptoms of undesirable combustion phenomena such as backfire and rapid rate of pressure rise. The results described in this paper centre round the experiments conducted on a research engine to study the effect of some critical operating parameters such as air-fuel ratio, ignition timing on the cylinder pressure and heat release rate using neat hydrogen gas. During these tests it was observed that an appropriately designed timed manifold Injection(TMI) system was extremely effective not only in getting rid of backfire, but also in ensuring ultralean operation resulting in drastic reduction in NOX emission level. An integrated control of several operating parameters showed that the if the engine was operated with fixed injection duration, peak pressure and rate of pressure rise showed an increasing trend with advanced spark timing. This could be due to the high burning velocity of hydrogen. (orig.)

  3. Towards a detailed soot model for internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Mosbach, Sebastian; Celnik, Matthew S.; Raj, Abhijeet; Kraft, Markus [Department of Chemical Engineering and Biotechnology, University of Cambridge, Pembroke Street, Cambridge CB2 3RA (United Kingdom); Zhang, Hongzhi R. [Department of Chemical Engineering, University of Utah, 1495 East 100 South, Kennecott Research Building, Salt Lake City, UT 84112 (United States); Kubo, Shuichi [Frontier Research Center, Toyota Central R and D Labs., Inc., Nagakute, Aichi 480-1192 (Japan); Kim, Kyoung-Oh [Higashifuji Technical Center, Toyota Motor Corporation, Mishuku 1200, Susono, Shizuoka 480-1193 (Japan)

    2009-06-15

    In this work, we present a detailed model for the formation of soot in internal combustion engines describing not only bulk quantities such as soot mass, number density, volume fraction, and surface area but also the morphology and chemical composition of soot aggregates. The new model is based on the Stochastic Reactor Model (SRM) engine code, which uses detailed chemistry and takes into account convective heat transfer and turbulent mixing, and the soot formation is accounted for by SWEEP, a population balance solver based on a Monte Carlo method. In order to couple the gas-phase to the particulate phase, a detailed chemical kinetic mechanism describing the combustion of Primary Reference Fuels (PRFs) is extended to include small Polycyclic Aromatic Hydrocarbons (PAHs) such as pyrene, which function as soot precursor species for particle inception in the soot model. Apart from providing averaged quantities as functions of crank angle like soot mass, volume fraction, aggregate diameter, and the number of primary particles per aggregate for example, the integrated model also gives detailed information such as aggregate and primary particle size distribution functions. In addition, specifics about aggregate structure and composition, including C/H ratio and PAH ring count distributions, and images similar to those produced with Transmission Electron Microscopes (TEMs), can be obtained. The new model is applied to simulate an n-heptane fuelled Homogeneous Charge Compression Ignition (HCCI) engine which is operated at an equivalence ratio of 1.93. In-cylinder pressure and heat release predictions show satisfactory agreement with measurements. Furthermore, simulated aggregate size distributions as well as their time evolution are found to qualitatively agree with those obtained experimentally through snatch sampling. It is also observed both in the experiment as well as in the simulation that aggregates in the trapped residual gases play a vital role in the soot

  4. Towards a detailed soot model for internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Kraft, Markus; Mosbach, Sebastian; Celnik, Matthew S. [Univ. of Cambridge (United Kingdom); Zhang, Hongzhi R. [Univ. of Utah (United States); Kubo, Shuichi; Kim, Kyoung-Oh [Toyota (Japan)

    2008-07-01

    In this work, we integrate previously developed models for engine combustion and soot formation. Namely, we combine the stochastic reactor model (SRM) engine code, which uses detailed chemistry and takes into account convective heat transfer and turbulent mixing, with SWEEP, a population balance solver based on a Monte Carlo method. In order to couple the two codes, a detailed chemical kinetic mechanism describing the combustion of primary reference fuels (PRFs) is extended to include small Polycyclic Aromatic Hydrocarbons (PAHs) such as pyrene, which function as soot precursor species for particle inception in the soot model. The integrated model provides not only averaged quantities as functions of crank angle like soot mass, volume fraction, aggregate diameter, and the number of primary particles per aggregate for example, but also more detailed information such as aggregate and primary particle size distribution functions. In addition, specifics about aggregate structure and composition, including C/H ratio and PAH ring count distributions, and images similar to those produced with transmission electron microscopes (TEMs), can be obtained. The combined model is applied to simulate an n-heptane fuelled homogeneous charge compression ignition (HCCI) engine which is operated at an equivalence ratio of 1.93. In-cylinder pressure and heat release predictions show satisfactory agreement with measurements. Furthermore, simulated aggregate size distributions as well as their time evolution are found to qualitatively agree with those obtained experimentally through snatch sampling. It is also seen both in the experiment as well as in the simulation that aggregates in the trapped residual gases play a vital role in the soot formation process. (orig.)

  5. Turbulence, combustion, efficiency and emission measurements on a supercharged natural gas SI engine

    Energy Technology Data Exchange (ETDEWEB)

    Einewall, P.; Olsson, Magnus

    1996-08-01

    LDV was used to measure turbulence in six different combustion chambers for a natural gas operated TD102 Volvo truck engine. The efficiency and emissions were measured during supercharged lean operation. The combustion chambers were altered by using pistons with different crown geometries. Some of the load cases require supercharged operation of the engine. The cooling of the cylinder-head was therefore improved. Turbulence, combustion rate, emissions and efficiency was measured for four different piston design. 8 refs, figs

  6. FY2011 Annual Progress Report for Advanced Combustion Engine Research and Development

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2011-12-01

    Annual Progress Report for the Advanced Combustion Engine Research and Development (R&D) subprogram supporting the mission of the Vehicle Technologies Program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future federal emissions regulations.

  7. Digital signal processing of cylinder pressure data for combustion diagnostics of HCCI engine

    Science.gov (United States)

    Kumar Maurya, Rakesh; Pal, Dev Datt; Kumar Agarwal, Avinash

    2013-03-01

    Diagnosis of combustion is necessary for the estimation of the combustion quality, and control of combustion timing in advanced combustion concepts like HCCI. Combustion diagnostics is often performed using digital processing of pressure signals measured using piezoelectric sensor installed in the combustion chamber of the engine. Four-step pressure signal processing consisting of (i) absolute pressure correction, (ii) phasing w.r.t. crank angle, (iii) cycle averaging and (iv) smoothening is used to get cylinder pressure data from the engine experiments, which is further analyzed to get information about combustion characteristics. This study focuses on various aspect of signal processing (cycle averaging and smoothing) of in-cylinder pressure signal from a HCCI engine acquired using a piezoelectric pressure sensor. Experimental investigations are conducted on a HCCI combustion engine operating at different engine speed/load/air-fuel ratio conditions. The cylinder pressure history of 3000 consecutive engine cycles is acquired for analysis using piezoelectric pressure sensor. This study determines the optimum number of engine cycles to be acquired for reasonably good pressure signals based on standard deviation of in-cylinder pressure, rate of pressure rise and rate of heat release signals. Different signal smoothening methods (using various digital filters) are also analyzed and their results are compared. This study also presents effect of signal processing methods on pressure, pressure rise rate and rate of heat release curves at different engine operating conditions.

  8. Combustion Characteristics of Liquid Normal Alkane Fuels in a Model Combustor of Supersonic Combustion Ramjet Engine

    Science.gov (United States)

    今村, 宰; 石川, 雄太; 鈴木, 俊介; 福本, 皓士郎; 西田, 俊介; 氏家, 康成; 津江, 光洋

    Effect of kinds of one-component n-alkane liquid fuels on combustion characteristics was investigated experimentally using a model combustor of scramjet engine. The inlet condition of a model combustor is 2.0 of Mach number, up to 2400K of total temperature, and 0.38MPa of total pressure. Five kinds of n-alkane are tested, of which carbon numbers are 7, 8, 10, 13, and 16. They are more chemically active and less volatile with an increase of alkane carbon number. Fuels are injected to the combustor in the upstream of cavity with barbotage nitrogen gas and self-ignition performance was investigated. The result shows that self-ignition occurs with less equivalence ratio when alkane carbon number is smaller. This indicates that physical characteristic of fuel, namely volatile of fuel, is dominant for self-ignition behavior. Effect on flame-holding performance is also examined with adding pilot hydrogen and combustion is kept after cutting off pilot hydrogen with the least equivalence ratio where alkane carbon number is from 8 to 10. These points are discussed qualitatively from the conflict effect of chemical and physical properties on alkane carbon number.

  9. Optical Study of Flow and Combustion in an HCCI Engine with Negative Valve Overlap

    Science.gov (United States)

    Wilson, Trevor S.; Xu, Hongming; Richardson, Steve; Wyszynski, Miroslaw L.; Megaritis, Thanos

    2006-07-01

    One of the most widely used methods to enable Homogeneous Charge Compression Ignition (HCCI) combustion is using negative valve overlapping to trap a sufficient quantity of hot residual gas. The characteristics of air motion with specially designed valve events having reduced valve lift and durations associated with HCCI engines and their effect on subsequent combustion are not yet fully understood. In addition, the ignition process and combustion development in such engines are very different from those in conventional spark-ignition or diesel compression ignition engines. Very little data has been reported concerning optical diagnostics of the flow and combustion in the engine using negative valve overlapping. This paper presents an experimental investigation into the in-cylinder flow characteristics and combustion development in an optical engine operating in HCCI combustion mode. PIV measurements have been taken under motored engine conditions to provide a quantitative flow characterisation of negative valve overlap in-cylinder flows. The ignition and combustion process was imaged using a high resolution charge coupled device (CCD) camera and the combustion imaging data was supplemented by simultaneously recorded in-cylinder pressure data which assisted the analysis of the images. It is found that the flow characteristics with negative valve overlapping are less stable and more valve event driven than typical spark ignition in-cylinder flows, while the combustion initiation locations are not uniformly distributed.

  10. Piston surface heat transfer during combustion in large marine diesel engines

    DEFF Research Database (Denmark)

    Jensen, Michael Vincent; Walther, Jens Honore

    2010-01-01

    In the design process of large marine diesel engines information on the maximum heat load on the piston surface experienced during the engine cycle is an important parameter. The peak heat load occurs during combustion when hot combustion products impinge on the piston surface. Although the maximum...... with burning off piston surface material. In this work the peak heat load on the piston surface of large marine diesel engines during combustion was investigated. Measurements of the instantaneous surface temperature and surface heat flux on pistons in large marine engines are difficult due to expensive...... was calculated under different conditions in the numerical setup in order to obtain information of the actual peak heat flux experienced at the piston in large marine diesel engines during combustion. The variation of physical parameters influencing the heat transfer during combustion included a variation...

  11. Surrogate fuel formulation for light naphtha combustion in advanced combustion engines

    KAUST Repository

    Ahmed, Ahfaz

    2015-03-30

    Crude oil once recovered is further separated in to several distinct fractions to produce a range of energy and chemical products. One of the less processed fractions is light naphtha (LN), hence they are more economical to produce than their gasoline and diesel counterparts. Recent efforts have demonstrated usage of LN as transportation fuel for internal combustion engines with slight modifications. In this study, a multicomponent surrogate fuel has been developed for light naphtha fuel using a multi-variable nonlinear constrained optimization scheme. The surrogate, consisting of palette species n-pentane, 2-methylhexane, 2-methylbutane, n-heptane and toluene, was validated against the LN using ignition quality tester following ASTM D6890 methodology. Comparison of LN and the surrogate fuel demonstrated satisfactory agreement.

  12. Tailoring next-generation biofuels and their combustion in next-generation engines.

    Energy Technology Data Exchange (ETDEWEB)

    Gladden, John Michael; Wu, Weihua; Taatjes, Craig A.; Scheer, Adam Michael; Turner, Kevin M.; Yu, Eizadora T.; O' Bryan, Greg; Powell, Amy Jo; Gao, Connie W.

    2013-11-01

    Increasing energy costs, the dependence on foreign oil supplies, and environmental concerns have emphasized the need to produce sustainable renewable fuels and chemicals. The strategy for producing next-generation biofuels must include efficient processes for biomass conversion to liquid fuels and the fuels must be compatible with current and future engines. Unfortunately, biofuel development generally takes place without any consideration of combustion characteristics, and combustion scientists typically measure biofuels properties without any feedback to the production design. We seek to optimize the fuel/engine system by bringing combustion performance, specifically for advanced next-generation engines, into the development of novel biosynthetic fuel pathways. Here we report an innovative coupling of combustion chemistry, from fundamentals to engine measurements, to the optimization of fuel production using metabolic engineering. We have established the necessary connections among the fundamental chemistry, engine science, and synthetic biology for fuel production, building a powerful framework for co-development of engines and biofuels.

  13. Study of combustion and emission characteristics of turbocharged diesel engine fuelled with dimethylether

    Institute of Scientific and Technical Information of China (English)

    Junhua WU; Zhen HUANG; Xinqi QIAO; Jun LU; Junjun ZHANG; Liang ZHANG

    2008-01-01

    An experimental study of a turbocharged diesel engine operating on dimethyl ether (DME) was conducted. The combustion and emission characteristics of the DME engine were investigated. The results show that the maximum torque and power of DME are greater than those of diesel, particularly at low speeds; the brake specific fuel consum-ption of DME is lower than that of diesel at low and middle engine speeds, and the injection delay of DME is longer than that of diesel. However, the maximum cylinder pressure, maximum pressure rise rate and combustion noises of the DME engine are lower than those of diesel. The combustion velocity of DME is faster than that of diesel, resulting in a shorter combustion duration of DME. Compared with the diesel engine, NOx emission of the DME engine is reduced by 41.6% on ESC data. In addition, the DME engine is smoke free at any operating condition.

  14. Status on the Verification of Combustion Stability for the J-2X Engine Thrust Chamber Assembly

    Science.gov (United States)

    Casiano, Matthew; Hinerman, Tim; Kenny, R. Jeremy; Hulka, Jim; Barnett, Greg; Dodd, Fred; Martin, Tom

    2013-01-01

    Development is underway of the J -2X engine, a liquid oxygen/liquid hydrogen rocket engine for use on the Space Launch System. The Engine E10001 began hot fire testing in June 2011 and testing will continue with subsequent engines. The J -2X engine main combustion chamber contains both acoustic cavities and baffles. These stability aids are intended to dampen the acoustics in the main combustion chamber. Verification of the engine thrust chamber stability is determined primarily by examining experimental data using a dynamic stability rating technique; however, additional requirements were included to guard against any spontaneous instability or rough combustion. Startup and shutdown chug oscillations are also characterized for this engine. This paper details the stability requirements and verification including low and high frequency dynamics, a discussion on sensor selection and sensor port dynamics, and the process developed to assess combustion stability. A status on the stability results is also provided and discussed.

  15. Development and test of combustion chamber for Stirling engine heated by natural gas

    Science.gov (United States)

    Li, Tie; Song, Xiange; Gui, Xiaohong; Tang, Dawei; Li, Zhigang; Cao, Wenyu

    2014-04-01

    The combustion chamber is an important component for the Stirling engine heated by natural gas. In the paper, we develop a combustion chamber for the Stirling engine which aims to generate 3˜5 kWe electric power. The combustion chamber includes three main components: combustion module, heat exchange cavity and thermal head. Its feature is that the structure can divide "combustion" process and "heat transfer" process into two apparent individual steps and make them happen one by one. Since natural gas can mix with air fully before burning, the combustion process can be easily completed without the second wind. The flame can avoid contacting the thermal head of Stirling engine, and the temperature fields can be easily controlled. The designed combustion chamber is manufactured and its performance is tested by an experiment which includes two steps. The experimental result of the first step proves that the mixture of air and natural gas can be easily ignited and the flame burns stably. In the second step of experiment, the combustion heat flux can reach 20 kW, and the energy utilization efficiency of thermal head has exceeded 0.5. These test results show that the thermal performance of combustion chamber has reached the design goal. The designed combustion chamber can be applied to a real Stirling engine heated by natural gas which is to generate 3˜5 kWe electric power.

  16. Thermochemical conversion of biomass in smouldering combustion across scales: The roles of heterogeneous kinetics, oxygen and transport phenomena.

    Science.gov (United States)

    Huang, Xinyan; Rein, Guillermo

    2016-05-01

    The thermochemical conversion of biomass in smouldering combustion is investigated here by combining experiments and modeling at two scales: matter (1mg) and bench (100g) scales. Emphasis is put on the effect of oxygen (0-33vol.%) and oxidation reactions because these are poorly studied in the literature in comparison to pyrolysis. The results are obtained for peat as a representative biomass for which there is high-quality experimental data published previously. Three kinetic schemes are explored, including various steps of drying, pyrolysis and oxidation. The kinetic parameters are found using the Kissinger-Genetic Algorithm method, and then implemented in a one-dimensional model of heat and mass transfer. The predictions are validated with thermogravimetric and bench-scale experiments and then analyzed to unravel the role of heterogeneous reaction. This is the first time that the influence of oxygen on biomass smouldering is explained in terms of both chemistry and transport phenomena across scales.

  17. Progress in the computation of flows in combustion in controlled ignition engines

    Energy Technology Data Exchange (ETDEWEB)

    Naji, H.; Borghi, R.; Souhaite, P.; Argueyrolles, B.

    1987-01-01

    The characterization by computation of reactive flows in the combustion chambers is now used directly to design piston engines. This computation requires numerical programs taking into account fluid mechanics, heat transfer, combustion and turbulence. For these flows, turbulence and combustion cannot be dissociated. Moreover the latter should be represented by a process with a finite speed. The existing program has been improved by incorporation of two combustion models. The turbulent fluctuations are taken into account by a modelisation of their probability densities. Numerical results show that the two models give a realistic values of the burnt fraction and of the average pressure during the combustion phase.

  18. Internal combustion engine report: Spark ignited ICE GenSet optimization and novel concept development

    Energy Technology Data Exchange (ETDEWEB)

    Keller, J.; Blarigan, P. Van [Sandia National Labs., Livermore, CA (United States)

    1998-08-01

    In this manuscript the authors report on two projects each of which the goal is to produce cost effective hydrogen utilization technologies. These projects are: (1) the development of an electrical generation system using a conventional four-stroke spark-ignited internal combustion engine generator combination (SI-GenSet) optimized for maximum efficiency and minimum emissions, and (2) the development of a novel internal combustion engine concept. The SI-GenSet will be optimized to run on either hydrogen or hydrogen-blends. The novel concept seeks to develop an engine that optimizes the Otto cycle in a free piston configuration while minimizing all emissions. To this end the authors are developing a rapid combustion homogeneous charge compression ignition (HCCI) engine using a linear alternator for both power take-off and engine control. Targeted applications include stationary electrical power generation, stationary shaft power generation, hybrid vehicles, and nearly any other application now being accomplished with internal combustion engines.

  19. Combustion in Homogeneous Charge Compression Ignition Engines: Experiments and Detailed Chemical Kinetic Simulations

    Energy Technology Data Exchange (ETDEWEB)

    Flowers, D L

    2002-06-07

    Homogeneous charge compression ignition (HCCI) engines are being considered as an alternative to diesel engines. The HCCI concept involves premixing fuel and air prior to induction into the cylinder (as is done in current spark-ignition engine) then igniting the fuel-air mixture through the compression process (as is done in current diesel engines). The combustion occurring in an HCCI engine is fundamentally different from a spark-ignition or Diesel engine in that the heat release occurs as a global autoignition process, as opposed to the turbulent flame propagation or mixing controlled combustion used in current engines. The advantage of this global autoignition is that the temperatures within the cylinder are uniformly low, yielding very low emissions of oxides of nitrogen (NO{sub x}, the chief precursors to photochemical smog). The inherent features of HCCI combustion allows for design of engines with efficiency comparable to, or potentially higher than, diesel engines. While HCCI engines have great potential, several technical barriers exist which currently prevent widespread commercialization of this technology. The most significant challenge is that the combustion timing cannot be controlled by typical in-cylinder means. Means of controlling combustion have been demonstrated, but a robust control methodology that is applicable to the entire range of operation has yet to be developed. This research focuses on understanding basic characteristics of controlling and operating HCCI engines. Experiments and detailed chemical kinetic simulations have been applied to the characterize some of the fundamental operational and design characteristics of HCCI engines. Experiments have been conducted on single and multi-cylinder engines to investigate general features of how combustion timing affects the performance and emissions of HCCI engines. Single-zone modeling has been used to characterize and compare the implementation of different control strategies. Multi

  20. Fundamentals of Fire Phenomena

    DEFF Research Database (Denmark)

    Quintiere, James

    Understanding fire dynamics and combustion is essential in fire safety engineering and in fire science curricula. Engineers and students involved in fire protection, safety and investigation need to know and predict how fire behaves to be able to implement adequate safety measures and hazard...... analyses. Fire phenomena encompass everything about the scientific principles behind fire behaviour. Combining the principles of chemistry, physics, heat and mass transfer, and fluid dynamics necessary to understand the fundamentals of fire phenomena, this book integrates the subject into a clear...... discipline. It covers thermo chemistry including mixtures and chemical reactions; Introduces combustion to the fire protection student; Discusses premixed flames and spontaneous ignition; Presents conservation laws for control volumes, including the effects of fire; Describes the theoretical bases...

  1. Abnormal combustion caused by lubricating oil in high BMEP gas engines

    Energy Technology Data Exchange (ETDEWEB)

    Yasueda, Shinji [Kyushu Univ. (Japan). GDEC Gas and Diesel Engine; Takasaki, Koji; Tajima, Hiroshi [Kyushu Univ. (Japan). Lab. of Engine and Combustion (ECO)

    2013-05-15

    In recent years, abnormal combustion with high peak firing pressure has been experienced on gas engines with high brake mean effective pressures. The abnormality is detected not as pre-ignition but as knocking. Research, including visualisation tests on a single-cylinder engine, has confirmed the phenomenon to be pre-ignition caused by the auto-ignition of in-cylinder lubricant, causing cyclical variations of peak firing pressure on premix combustion gas engines. (orig.)

  2. Quantum Hamiltonian daemons: Unitary analogs of combustion engines

    Science.gov (United States)

    Thesing, Eike P.; Gilz, Lukas; Anglin, James R.

    2017-07-01

    Hamiltonian daemons have recently been defined classically as small, closed Hamiltonian systems which can exhibit secular energy transfer from high-frequency to low-frequency degrees of freedom (steady downconversion), analogous to the steady transfer of energy in a combustion engine from the high terahertz frequencies of molecular excitations to the low kilohertz frequencies of piston motion [L. Gilz, E. P. Thesing, and J. R. Anglin, Phys. Rev. E 94, 042127 (2016), 10.1103/PhysRevE.94.042127]. Classical daemons achieve downconversion within a small, closed system by exploiting nonlinear resonances; the adiabatic theorem permits their operation but imposes nontrivial limitations on their efficiency. Here we investigate a simple example of a quantum mechanical daemon. In the correspondence regime it obeys similar efficiency limits to its classical counterparts, but in the strongly quantum mechanical regime the daemon operates in an entirely different manner. It maintains an engine-like behavior in a distinctly quantum mechanical form: a weight is lifted at a steady average speed through a long sequence of quantum jumps in momentum, at each of which a quantum of fuel is consumed. The quantum daemon can cease downconversion at any time through nonadiabatic Landau-Zener transitions, and continuing operation of the quantum daemon is associated with steadily growing entanglement between fast and slow degrees of freedom.

  3. Signal Processing Methods for Liquid Rocket Engine Combustion Stability Assessments

    Science.gov (United States)

    Kenny, R. Jeremy; Lee, Erik; Hulka, James R.; Casiano, Matthew

    2011-01-01

    The J2X Gas Generator engine design specifications include dynamic, spontaneous, and broadband combustion stability requirements. These requirements are verified empirically based high frequency chamber pressure measurements and analyses. Dynamic stability is determined with the dynamic pressure response due to an artificial perturbation of the combustion chamber pressure (bomb testing), and spontaneous and broadband stability are determined from the dynamic pressure responses during steady operation starting at specified power levels. J2X Workhorse Gas Generator testing included bomb tests with multiple hardware configurations and operating conditions, including a configuration used explicitly for engine verification test series. This work covers signal processing techniques developed at Marshall Space Flight Center (MSFC) to help assess engine design stability requirements. Dynamic stability assessments were performed following both the CPIA 655 guidelines and a MSFC in-house developed statistical-based approach. The statistical approach was developed to better verify when the dynamic pressure amplitudes corresponding to a particular frequency returned back to pre-bomb characteristics. This was accomplished by first determining the statistical characteristics of the pre-bomb dynamic levels. The pre-bomb statistical characterization provided 95% coverage bounds; these bounds were used as a quantitative measure to determine when the post-bomb signal returned to pre-bomb conditions. The time for post-bomb levels to acceptably return to pre-bomb levels was compared to the dominant frequency-dependent time recommended by CPIA 655. Results for multiple test configurations, including stable and unstable configurations, were reviewed. Spontaneous stability was assessed using two processes: 1) characterization of the ratio of the peak response amplitudes to the excited chamber acoustic mode amplitudes and 2) characterization of the variability of the peak response

  4. Traveling-Wave Thermoacoustic Engines With Internal Combustion

    Science.gov (United States)

    Weiland, Nathan Thomas; Zinn, Ben T.; Swift, Gregory William

    2004-05-11

    Thermoacoustic devices are disclosed wherein, for some embodiments, a combustion zone provides heat to a regenerator using a mean flow of compressible fluid. In other embodiments, burning of a combustible mixture within the combustion zone is pulsed in phase with the acoustic pressure oscillations to increase acoustic power output. In an example embodiment, the combustion zone and the regenerator are thermally insulated from other components within the thermoacoustic device.

  5. Comprehensive study of biodiesel fuel for HSDI engines in conventional and low temperature combustion conditions

    Energy Technology Data Exchange (ETDEWEB)

    Tormos, Bernardo; Novella, Ricardo; Garcia, Antonio; Gargar, Kevin [CMT-Motores Termicos, Universidad Politecnica de Valencia, Valencia, ES, Campus de Vera, s/n, Edificio 6D. Camino de Vera s/n, 46022 Valencia (Spain)

    2010-02-15

    In this research, an experimental investigation has been performed to give insight into the potential of biodiesel as an alternative fuel for High Speed Direct Injection (HSDI) diesel engines. The scope of this work has been broadened by comparing the combustion characteristics of diesel and biodiesel fuels in a wide range of engine loads and EGR conditions, including the high EGR rates expected for future diesel engines operating in the low temperature combustion (LTC) regime. The experimental work has been carried out in a single-cylinder engine running alternatively with diesel and biodiesel fuels. Conventional diesel fuel and neat biodiesel have been compared in terms of their combustion performance through a new methodology designed for isolating the actual effects of each fuel on diesel combustion, aside from their intrinsic differences in chemical composition. The analysis of the results has been sequentially divided into two progressive and complementary steps. Initially, the overall combustion performance of each fuel has been critically evaluated based on a set of parameters used as tracers of the combustion quality, such as the combustion duration or the indicated efficiency. With the knowledge obtained from this previous overview, the analysis focuses on the detailed influence of biodiesel on the different diesel combustion stages known ignition delay, premixed combustion and mixing controlled combustion, considering also the impact on CO and UHC (unburn-hydrocarbons) pollutant emissions. The results of this research explain why the biodiesel fuel accelerates the diesel combustion process in all engine loads and EGR rates, even in those corresponding with LTC conditions, increasing its possibilities as alternative fuel for future DI diesel engines. (author)

  6. Numerical study on the combustion process of a biogas spark-ignition engine

    Directory of Open Access Journals (Sweden)

    Carrera José L.

    2013-01-01

    Full Text Available The fuel called biogas is obtained through anaerobic digestion of different types of organic waste, providing a way to tap the energy stored in organic matter. The use of this fuel is also attractive from the standpoint of global warming because its application does not register a net emission of carbon dioxide into the atmosphere. One possible use for this fuel is to feed the spark-ignition internal combustion engines. In the present, there is little information available about the process of combustion in internal combustion engines fueled by biogas. The combustion process of an internal combustion engine ignition powered by biogas is characterized in terms of the duration of combustion, i.e., depending on the time elapsed while the reactants (methane and oxygen are transformed into products (mainly carbon dioxide and water. This study numerically evaluates the way in which the geometrical parameters such as the compression ratio and operating parameters like engine speed, the excess air, the time of spark timing and carbon dioxide content of biogas affect the evolution of the combustion process. To carry out this study, a five factors and two levels experiment was designed and conducted, based on which, the most influential parameters were identified. Equations expressing the combustion characteristic parameters, as a function of the geometric and operation parameters of a spark ignited engines, are delivered as a result.

  7. Study on Model Based Combustion Control of Diesel Engine with Multi Fuel Injection

    Science.gov (United States)

    Ikemura, R.; Yamasaki, Y.; Kaneko, S.

    2016-09-01

    A controller for model-based control of diesel engine with triple injection were developed with a combustion model. In the combustion model, an engine cycle is discretized into several representative points in order to improve calculation speed, while physical equations are employed to expand the versatility. The combustion model can predict in-cylinder pressure and temperature in these discrete points. Prediction accuracy of the combustion model was evaluated by comparison with experimental result. A controller was designed with the combustion model in order to calculate optimal fuel injection pattern for controlling in-cylinder pressure peak timing. The controller's performance was evaluated through simulation in which the combustion model was used as a plant model.

  8. Combustion and emission analysis of heavy-duty vehicle diesel engine

    Science.gov (United States)

    Sun, Zhixin; Wang, Xue; Wang, Xiancheng; Zhou, Jingkai

    2017-03-01

    Aiming at the research on combustion and emission characteristics of heavy-duty vehicle diesel engine, a bench test was carried out for PM and NOx emission for a certain type diesel engine under different speed and loads. Results shows that for this type of heavy-duty vehicle diesel engine, ignition delay is longer and the proportion of diffusion combustion increases under high speed of external characteristics conditions. Under the speed of 1400 r/min, ignition delay decreases with load increases, combustion duration shortened at first, then increases, the proportion of diffusion combustion increases. The ignition delay is longer and cylinder temperature is higher under lower speed external characteristics of diesel engine, the emissions of soot and NOx are heavier; with large load of external characteristics of diesel engine, the emissions of soot and NOx are heavy as well.

  9. Piston surface heat transfer during combustion in large marine diesel engines

    DEFF Research Database (Denmark)

    Jensen, Michael Vincent; Walther, Jens Honore

    2010-01-01

    limited. The numerical investigation focused on the simulation of a hot turbulent gas jet impinging on a wall under very high pressure, thus approximating the process of the actual impingement of hot combustion gasses on the piston surface during combustion. The surface heat flux at the wall......In the design process of large marine diesel engines information on the maximum heat load on the piston surface experienced during the engine cycle is an important parameter. The peak heat load occurs during combustion when hot combustion products impinge on the piston surface. Although the maximum...... instrumentation and high engine running costs compared to automotive engines. Therefore the investigation in this work was carried out numerically with the use of a computational fluid dynamics (CFD) code. At the same time, numerical work on detailed in-cylinder wall heat transfer in engines has been quite...

  10. FY2009 Annual Progress Report for Advanced Combustion Engine Research and Development

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2009-12-01

    Fiscal Year 2009 Annual Progress Report for the Advanced Combustion Engine Research and Development (R&D) subprogram. The Advanced Combustion Engine R&D subprogram supports the mission of the VTP program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future Federal emissions regulations. Dramatically improving the efficiency of ICEs and enabling their introduction in conventional as well as hybrid electric vehicles is the most promising and cost-effective approach to increasing vehicle fuel economy over the next 30 years.

  11. Combustion Commonality and Differences Between HSDI and Heavy Duty Truck Engines

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Rong

    2000-08-20

    Experimental understanding of the diesel spray and combustion process at the fundamental level has helped advance the virtual lab simulation tools. The computational fluid dynamics (CFD)-based simulation has been globally verified in many engines, providing substantial credibility to the use of this technology in advanced engine development. This paper highlights the common aspects and differences between the smallbore HSDI and the larger displacement heavy-duty truck engine spray and combustion processes. Implications for combustion system strategies will be delineated. Detroit Diesel integrated ''Wired'' approach will be explained with pointers towards future tool enhancements.

  12. In-cylinder Flow Characterisation of Heavy Duty Diesel Engines Using Combustion Image Velocimetry

    OpenAIRE

    Dembinski, Henrik

    2014-01-01

    In-cylinder flow in diesel engines has a large impact on combustion and emission formation. In this work, the flow is characterised with a new measurement method called combustion image velocimetry (CIV). This technique is used to explain how airflow introduced during induction affects soot emissions and interacts with injection pressures up to 2500 bar. The CIV measurements enable flow analysis during the combustion and post-oxidation phases. The flow velocities inside the cylinder of a heav...

  13. Investigation of Bio-Diesel Fueled Engines under Low-Temperature Combustion Strategies

    Energy Technology Data Exchange (ETDEWEB)

    Chia-fon F. Lee; Alan C. Hansen

    2010-09-30

    In accordance with meeting DOE technical targets this research was aimed at developing and optimizing new fuel injection technologies and strategies for the combustion of clean burning renewable fuels in diesel engines. In addition a simultaneous minimum 20% improvement in fuel economy was targeted with the aid of this novel advanced combustion system. Biodiesel and other renewable fuels have unique properties that can be leveraged to reduce emissions and increase engine efficiency. This research is an investigation into the combustion characteristics of biodiesel and its impacts on the performance of a Low Temperature Combustion (LTC) engine, which is a novel engine configuration that incorporates technologies and strategies for simultaneously reducing NOx and particulate emissions while increasing engine efficiency. Generating fundamental knowledge about the properties of biodiesel and blends with petroleum-derived diesel and their impact on in-cylinder fuel atomization and combustion processes was an important initial step to being able to optimize fuel injection strategies as well as introduce new technologies. With the benefit of this knowledge experiments were performed on both optical and metal LTC engines in which combustion and emissions could be observed and measured under realistic conditions. With the aid these experiments and detailed combustion models strategies were identified and applied in order to improve fuel economy and simultaneously reduce emissions.

  14. Spray and combustion visualization of bio-diesel in a direct injection diesel engine

    Directory of Open Access Journals (Sweden)

    Pan Jianfeng

    2013-01-01

    Full Text Available By using the self-developed dynamic visualization photographic setup, this article investigated some major factors affecting the spray and combustion process of diesel engine fueled by biodiesel. The experimental results show: With the increase of biodiesel percentage, fuel injection advances slightly, the ignition delay becomes shorter and the duration of combustion lengthens. Engine speed has little effect on the spray. However, the combustion rate is increased and the burning time becomes shorter with the increase of engine speed, although the duration of combustion in terms of crank angle increases. With the increase of needle opening pressure, both the spray cone angle and the spray penetration of biodiesel increases, the atomization of spray improves, the ignition delay and the duration of combustion becomes shorter, the peak pressure increases.

  15. A stochastic model for the indicated pressure process and the dynamics of the internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Rizzoni, G. (Michigan Univ., Ann Arbor, MI (USA). Dept. of Electrical Engineering and Computer Science)

    1989-08-01

    In-cylinder gas pressure has long been recognized as a fundamental measure of performance in the internal combustion engine. Among the issues that have been the subject of research in recent years is the study of the effects cyclic combustion variability has on the cycle-to-cycle and cylinder-to-cylinder fluctuations in combustion pressures. Some of the research problems pertaining to cyclic combustion variability are to reformulate from a perspective markedly different from the fluid dynamic and thermodynamic models which traditionally characterize this research: a system viewpoint is embraced to construct a stochastic model for the indicated pressure process and the dynamics of the internal combustion engine. First a deterministic model for the dynamics of the engine is described; then a stochastic model is proposed for the cylinder pressure process. The deterministic model and the stochastic representation are then tied together in a Kalman filter model. Experimental results are discussed to validate the models.

  16. Transpiring Cooling of a Scram-Jet Engine Combustion Chamber

    Science.gov (United States)

    Choi, Sang H.; Scotti, Stephen J.; Song, Kyo D.; Ries,Heidi

    1997-01-01

    The peak cold-wall heating rate generated in a combustion chamber of a scram-jet engine can exceed 2000 Btu/sq ft sec (approx. 2344 W/sq cm). Therefore, a very effective heat dissipation mechanism is required to sustain such a high heating load. This research focused on the transpiration cooling mechanism that appears to be a promising approach to remove a large amount of heat from the engine wall. The transpiration cooling mechanism has two aspects. First, initial computations suggest that there is a reduction, as much as 75%, in the heat flux incident on the combustion chamber wall due to the transpirant modifying the combustor boundary layer. Secondly, the heat reaching the combustor wall is removed from the structure in a very effective manner by the transpirant. It is the second of these two mechanisms that is investigated experimentally in the subject paper. A transpiration cooling experiment using a radiant heating method, that provided a heat flux as high as 200 Btu/sq ft sec ( approx. 234 W/sq cm) on the surface of a specimen, was performed. The experiment utilized an arc-lamp facility (60-kW radiant power output) to provide a uniform heat flux to a test specimen. For safety reasons, helium gas was used as the transpirant in the experiments. The specimens were 1.9-cm diameter sintered, powdered-stainless-steel tubes of various porosities and a 2.54cm square tube with perforated multi-layered walls. A 15-cm portion of each specimen was heated. The cooling effectivenes and efficiencies by transpiration for each specimen were obtained using the experimental results. During the testing, various test specimens displayed a choking phenomenon in which the transpirant flow was limited as the heat flux was increased. The paper includes a preliminary analysis of the transpiration cooling mechanism and a scaling conversion study that translates the results from helium tests into the case when a hydrogen medium is used.

  17. Ignition and combustion phenomena on a moving grate: with application to the thermal conversion of biomass and municipal solid waste

    NARCIS (Netherlands)

    Blijderveen, M.

    2012-01-01

    Combustion can be defined as a fast oxidation process of a solid, gaseous or liquid fuel at elevated temperatures. In any combustion process, ignition plays an essential role. Not only to initiate the combustion process, but also to maintain it. Especially in solid fuel combustion on a grate, where

  18. Research status of key techniques for shock-induced combustion ramjet(shcramjet) engine

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    As one of the most promising propulsion systems in the future,shock-induced combustion ramjet engine can remedy the disadvantages in the integrated design of scramjet engine and airframe.It can shorten the length of the combustor,lighten the structure weight of the engine and keep better performance in a broad range of flight Mach number.The elementary principle of shock-induced combustion ramjet engine is introduced.The key technologies of this kind of propulsion system are described,while their research status is presented in detail.Suggestion on the development of shcramjet engine in China is put forward.

  19. An experiment study of homogeneous charge compression ignition combustion and emission in a gasoline engine

    Directory of Open Access Journals (Sweden)

    Zhang Jianyong

    2014-01-01

    Full Text Available Homogenous charge compression ignition (HCCI technology has exhibited high potential to reduce fuel consumption and NOx emissions over normal spark ignition engines significantly. Optimized kinetic process (OKP technology is implemented to realize HCCI combustion in a port fuel injection gasoline engine. The combustion and emission characteristics are investigated with variation of intake air temperature, exhaust gas recirculation (EGR rate and intake air pressure. The results show that intake air temperature has great influence on HCCI combustion characteristic. Increased intake air temperature results in advance combustion phase, shorten combustion duration, and lower indicated mean effective pressure (IMEP. Increased EGR rate retards combustion start phase and prolongs combustion duration, while maximum pressure rising rate and NOx emission are reduced with increase of EGR rate. In the condition with constant fuel flow quantity, increased air pressure leads to retarded combustion phase and lower pressure rising rate, which will reduce the engine knocking tendency. In the condition with constant air fuel ratio condition, fuel injection quantity increases as intake air pressure increases, which lead to high heat release rate and high emission level. The optimal intake air temperature varies in different operating area, which can be tuned from ambient temperature to 220℃ by heat management system. The combination of EGR and air boost technology could expand operating area of HCCI engine, which improve indicated mean effective pressure from maximum 510kPa to 720kPa.

  20. Mechanical signature analysis using time-frequency signal processing: Application to internal combustion engine knock detection

    Energy Technology Data Exchange (ETDEWEB)

    Samimy, B. [Ford Motor Co., Dearborn, MI (United States). Advanced Vehicle Technology Div.; Rizzoni, G. [Ohio State Univ., Columbus, OH (United States)

    1996-09-01

    Signature analysis consists of the extraction of information from measured signal patterns. The work presented in this paper illustrates the use of time-frequency (TF) analysis methods for the purpose of mechanical signature analysis. Mechanical signature analysis is a mature and developed field; however, TF analysis methods are relatively new to the field of mechanical signal processing, having mostly been developed in the present decade, and have not yet been applied to their full potential i this field of engineering applications. Some of the ongoing efforts are briefly reviewed in this paper. One important application of TF mechanical signature analysis is the diagnosis of faults in mechanical systems. In this paper the authors illustrate how the use of joint TF signal representations can result in tangible benefits when analyzing signatures generated by transient phenomena in mechanical systems, such as might be caused by faults or otherwise abnormal operation. This paper also explores signal detection concepts in the joint TF domain and presents their application to the detection of internal combustion engine knock.

  1. Fundamental phenomena on fuel decomposition and boundary-layer combustion processes with applications to hybrid rocket motors

    Science.gov (United States)

    Kuo, Kenneth K.; Lu, Yeu-Cherng; Chiaverini, Martin J.; Harting, George C.; Johnson, David K.; Serin, Nadir

    1995-01-01

    The experimental study on the fundamental processes involved in fuel decomposition and boundary-layer combustion in hybrid rocket motors is continuously being conducted at the High Pressure Combustion Laboratory of The Pennsylvania State University. This research will provide a useful engineering technology base in the development of hybrid rocket motors as well as a fundamental understanding of the complex processes involved in hybrid propulsion. A high-pressure, 2-D slab motor has been designed, manufactured, and utilized for conducting seven test firings using HTPB fuel processed at PSU. A total of 20 fuel slabs have been received from the Mcdonnell Douglas Aerospace Corporation. Ten of these fuel slabs contain an array of fine-wire thermocouples for measuring solid fuel surface and subsurface temperatures. Diagnostic instrumentation used in the test include high-frequency pressure transducers for measuring static and dynamic motor pressures and fine-wire thermocouples for measuring solid fuel surface and subsurface temperatures. The ultrasonic pulse-echo technique as well as a real-time x-ray radiography system have been used to obtain independent measurements of instantaneous solid fuel regression rates.

  2. The railplug: A new ignitor for internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Faidley, R.W.; Darden, M.H.; Weldon, W.F.

    1995-01-01

    A miniaturized railgun, termed the {open_quotes}railplug,{close_quotes} has been developed for use as an ignitor of combustible mixtures in engines. The device drives a plasma armature in a multishot mode with the aim of creating a line-source for ignition rather than the point source provided by traditional spark plugs. Railplugs have been fabricated in both parallel rail and co-axial rail geometries. The railplug differs from most plasma armature railguns in two striking ways: (1) no fuse or pellet is used to initially establish the plasma (the armature is simply the arc created by a high-voltage pulse), and (2) it operates over a range of elevated pressures (up to 500 psi). Consequently, the railplug power supply must provide a high voltage spike to breakdown the gap between the rails followed by a sustaining voltage that supplies current to drive the arc down the rails. Conceptually, this is the equivalent of combining the electrostatic problem of a sparkplug with the electrodynamic one of a railgun. Two power supply options that do this are outlined, as well as details of railplug geometries. Successes to date have demonstrated the firing of plugs for over 10{sup 4} shots at delivered arc energies of 1 J per shot. Rep rates have been demonstrated up to 50 Hz.

  3. Internal combustion engines performance simulation; Simulacao de desempenho de motores de combustao interna

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Jose F.C.; Barbosa, Joao R. [Centro Tecnico Aeroespacial, Sao Jose dos Campos, SP (Brazil). Inst. Tecnologico de Aeronautica. Dept. de Energia]. E-mail: monteiro@asap.iae.cta.br; barbosa@mec.ita.cta.br

    2000-07-01

    A study of numerical methods for the simulation of internal combustion engines is presented. Functional blocks, representing each component of the engine, can be combined to simulate the engine. A model was selected for each component. The engine simulation is carried out connecting the functional blocks. The inviscid conservation equations coupled with loss models where solved using a C++ computer program. Engine performance simulation is shown and results compared with published data. (author)

  4. Combustion Analysis and Knock Detection in Single Cylinder DI-Diesel Engine Using Vibration Signature Analysis

    OpenAIRE

    Y.V.V.SatyanarayanaMurthy

    2011-01-01

    The purpose of this paper is to detect the “knock” in Diesel engines which deteriorate the engine performance adversely. The methodology introduced in the present work suggests a newly developed approach towards analyzing the vibration analysis of diesel engines. The method is based on fundamental relationship between the engine vibration pattern and the relative characteristics of the combustion process in each or different cylinders. Knock in diesel engine is detected by measuring the vibra...

  5. Clean Air Act Standards and Guidelines for Energy, Engines, and Combustion

    Science.gov (United States)

    This page contains the stationary sources of air pollution for the energy, engines, and combustion industries, and their corresponding air pollution regulations. To learn more about the regulations for each industry, just click on the links below.

  6. Influences of Catalytic Combustion on the Ignition Timing and Emissions of HCCI Engines

    Institute of Scientific and Technical Information of China (English)

    ZENG Wen; XIE Mao-zhao

    2008-01-01

    The combustion processes of homogeneous charge compression ignition (HCCI) engines whose piston surfaces have been coated with catalyst (rhodium or platinum) were numerically investigated. A single-zone model and a multi-zone model were developed. The effects of catalytic combustion on the ignition timing of the HCCI engine were analyzed through the single-zone model. The results showed that the ignition timing of the HCCI engine was advanced by the catalysis. The effects of catalytic combustion on HC, CO and NOx emissions of the HCCI engine were analyzed through the multi-zone model. The results showed that the emissions of HC and CO (using platinum (Pt) as catalyst) were decreased, while the emissions of NOx were elevated by catalytic combustion. Compared with catalyst Pt, the HC emissions were lower with catalyst rhodium(Rh) on the piston surface, but the emissions of NOx and CO were higher.

  7. Possibilities to identify engine combustion model parameters by analysis of the instantaneous crankshaft angular speed

    Directory of Open Access Journals (Sweden)

    Popović Slobodan J.

    2014-01-01

    Full Text Available In this paper, novel method for obtaining information about combustion process in individual cylinders of a multi-cylinder Spark Ignition Engine based on instantaneous crankshaft angular velocity is presented. The method is based on robust box constrained Levenberg-Marquardt minimization of nonlinear Least Squares given for measured and simulated instantaneous crankshaft angular speed which is determined from the solution of the engine dynamics torque balance equation. Combination of in-house developed comprehensive Zero-Dimensional Two-Zone SI engine combustion model and analytical friction loss model in angular domain have been applied to provide sensitivity and error analysis regarding Wiebe combustion model parameters, heat transfer coefficient and compression ratio. The analysis is employed to evaluate the basic starting assumption and possibility to provide reliable combustion analysis based on instantaneous engine crankshaft angular speed. [Projekat Ministarstva nauke Republike Srbije, br. NPEE-290025 and TR-14074

  8. Studies on orange oil methyl ester in diesel engine with hemispherical and toroidal combustion chamber

    Directory of Open Access Journals (Sweden)

    Karthickeyan Viswanathan

    2016-01-01

    Full Text Available An investigation has been made to compare the emission characteristics of 20% orange oil methyl ester and 80% diesel in volumetric basis with Neat diesel in hemispherical combustion chamber and toroidal combustion chamber. Non-edible orange oil is selected and utilized to prepare alternative fuel to be utilized in Diesel engine. The traditional method of transestrification is employed for preparation orange oil methyl ester. The chemical properties of prepared methyl ester were determined using fouriertransform infrared spectroscopy method. Further its fuel properties were found based on American Society for Testing and Materials standards and compared with Neat diesel fuel properties. A compression ignition engine with electrical dynamometer test rig with gas analyzer has been used. It is observed that 1% of NOx and 4% of HC emission reduced in toroidal combustion chamber engine. However, smoke emission is found to be lower in hemispherical combustion chamber engine.

  9. PARAMETER MATCHING OF INTERNAL COMBUSTION ENGINE AND ELECTROMECHANICAL POWER TRAIN OF WHEEL TRACTOR

    Directory of Open Access Journals (Sweden)

    A. Kliuchnikov

    2012-01-01

    Full Text Available The paper considers stepless electromechanical power train of a wheel tractor. Methodology for parameter matching of electromechanical transmission and internal combustion engine for their optimum performance as part of a power wheel tractor unit. 

  10. Knock characteristics of dual-fuel combustion in diesel engines using natural gas as primary fuel

    Indian Academy of Sciences (India)

    O M I Nwafor

    2002-06-01

    This paper investigates the combustion knock characteristics of diesel engines running on natural gas using pilot injection as means of initiating combustion. The diesel engines knock under normal operating conditions but the knock referred to in this paper is an objectionable one. In the dual-fuel combustion process we have the ignition stage followed by the combustion stage. There are three types of knock: diesel knock, spark knock and knock due to secondary ignition delay of the primary fuel (erratic knock). Several factors have been noted to feature in defining knock characteristics of dual-fuel engines that include ignition delay, pilot quantity, engine load and speed, turbulence and gas flow rate.

  11. Combustion of jojoba methyl ester in an indirect injection diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Selim, M.Y.E. [United Arab Emirates University, Al-Ain (United Arab Emirates). Mechanical Engineering Dept.; Radwan, M.S.; Elfeky, S.M.S. [Helwan University, Cairo (Egypt). Mechanical Power Engineering Dept.

    2003-07-01

    An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

  12. Problems of providing completeness of the methane-containing block-jet combustion in a rocket-ramjet engine's combustion chamber

    Science.gov (United States)

    Timoshenko, Valeriy I.; Belotserkovets, Igor S.; Gusinin, Vjacheslav P.

    2009-11-01

    Some problems of methane-containing hydrocarbon fuel combustion are discussed. It seems that reduction of methane burnout zone length is one from main problems of designing new type engine. It is very important at the creation of combustion chambers of a rocket-ramjet engine for prospective space shuttle launch vehicles.

  13. FY2010 Annual Progress Report for Advanced Combustion Engine Research and Development

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Gurpreet [Office of Energy Efficiency and Renewable Energy (EERE), Washington, DC (United States)

    2010-12-01

    The Advanced Combustion Engine R&D subprogram supports the mission of the Vehicle Technologies Program by removing the critical technical barriers to commercialization of advanced internal combustion engines (ICEs) for passenger and commercial vehicles that meet future Federal emissions regulations. Dramatically improving the efficiency of ICEs and enabling their introduction in conventional as well as hybrid electric vehicles is the most promising and cost-effective approach to increasing vehicle fuel economy over the next 30 years.

  14. Experimental investigation of CAI combustion in a two-stroke poppet valve DI engine

    OpenAIRE

    Zhang, Yan

    2015-01-01

    This thesis was submitted for the award of Doctor of Philosophy and was awarded by Brunel University London Due to their ability to simultaneously reduce fuel consumption and NOx emissions, Controlled Auto Ignition (CAI) and HCCI combustion processes have been extensively researched over the last decade and adopted on prototype gasoline engines. These combustion processes were initially achieved on conventional two-stroke ported gasoline engines, but there have been significantly fewer stu...

  15. Indicated mean effective pressure oscillations in a natural gas combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Litak, Grzegorz [Dept. of Applied Mechanics, Lublin Univ. of Tech., Lublin (Poland); Dipt. di Architettura, Costruzioni e Strutture, Univ. Politecnica delle Marche, Ancona (Italy); Geca, Michal [Dept. of Applied Mechanics, Lublin Univ. of Tech., Lublin (Poland); Dept. of Thermodynamics, Fluid Mechanics and Aircraft Propulsion, Lublin Univ. of Tech., Lublin (Poland); Yao Bao-Feng; Li Guo-Xiu [School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong Univ., BJ (China)

    2009-05-15

    Fluctuations in a combustion process of natural gas in the internal spark ignition engine have been investigated. We measured pressure of the cyclic combustion and expressed its cyclic oscillations in terms of indicated mean effective pressure per cycle. By applying the statistical and multifractal analysis to the corresponding time series we show the considerable changes in engine dynamics for a different equivalence ratio decreases from 0.781 to very lean conditions. (orig.)

  16. Dual-Fuel Combustion for Future Clean and Efficient Compression Ignition Engines

    Directory of Open Access Journals (Sweden)

    Jesús Benajes

    2016-12-01

    Full Text Available Stringent emissions limits introduced for internal combustion engines impose a major challenge for the research community. The technological solution adopted by the manufactures of diesel engines to meet the NOx and particle matter values imposed in the EURO VI regulation relies on using selective catalytic reduction and particulate filter systems, which increases the complexity and cost of the engine. Alternatively, several new combustion modes aimed at avoiding the formation of these two pollutants by promoting low temperature combustion reactions, are the focus of study nowadays. Among these new concepts, the dual-fuel combustion mode known as reactivity controlled compression ignition (RCCI seems more promising because it allows better control of the combustion process by means of modulating the fuel reactivity depending on the engine operating conditions. The present experimental work explores the potential of different strategies for reducing the energy losses with RCCI in a single-cylinder research engine, with the final goal of providing the guidelines to define an efficient dual-fuel combustion system. The results demonstrate that the engine settings combination, piston geometry modification, and fuel properties variation are good methods to increase the RCCI efficiency while maintaining ultra-low NOx and soot emissions for a wide range of operating conditions.

  17. Effect of biofuel E85 combustion on fuel consumption in spark-ignition engines

    Directory of Open Access Journals (Sweden)

    Adam Polcar

    2012-01-01

    Full Text Available Biofuels represent an alternative source of energy that should gradually decrease our dependence on crude oil. A rapid development of their use in combustion engines is above all the consequence of their very positive balance of emissions. The possibility of use of biofuels in conventional combustion engines is given by their physico-chemical properties. Bioethanol is one of biofuels that can be used in spark-ignition engines. However, because of its lower heating value, it is necessary to change the mixing ratio fuel/air. The aim of this paper is to evaluate the effect of combustion of a mixture of bioethanol with gasoline (in the ratio 85:15 on fuel consumption in the spark-ignition engine. Experimental measurements were performed using a six-cylinder spark-ignition Peugeot engine with the overall volume of 2.946 cm3, which was equipped with a multi-hole system of indirect injection. Obtained results indicated that the combustion of E85 biofuel markedly increased the reduction of specific fuel consumption (corrected to atmospheric conditions. As compared with gasoline Natural 95, the actual volume consumption of E85 biofuel increased under the maximum engine load in average by 30.4 %. In spite of a relatively high consumption of E85 biofuel the total costs associated with running of a modified engine were lower than those of the engine combusting gasoline Natural 95.

  18. Effects of oxygen enriched combustion on pollution and performance characteristics of a diesel engine

    Directory of Open Access Journals (Sweden)

    P. Baskar

    2016-03-01

    Full Text Available Oxygen enriched combustion is one of the attractive combustion technologies to control pollution and improve combustion in diesel engines. An experimental test was conducted on a single cylinder direct injection diesel engine to study the impact of oxygen enrichment on pollution and performance parameters by increasing the oxygen concentration of intake air from 21 to 27% by volume. The tests results show that the combustion process was improved as there is an increase in thermal efficiency of 4 to 8 percent and decrease in brake specific fuel consumption of 5 to 12 percent. There is also a substantial decrease in unburned hydro carbon, carbon mono-oxide and smoke density levels to the maximum of 40, 55 and 60 percent respectively. However, there is a considerable increase in nitrogen oxide emissions due to increased combustion temperature and extra oxygen available which needs to be addressed.

  19. An assessment of combustion products of spark ignition engines supplied by ethanol - gasoline blends

    Science.gov (United States)

    Uzuneanu, K.; Golgotiu, E.

    2016-08-01

    The causes of environmental pollution by internal combustion engines arise from the use of fuels containing bounded carbon, from the fact that combustion takes place on a cyclic basis and at high temperature. The first and the last causes are directly related to the fuel and therefore there is in principle a possibility to reduce pollution by acting upon the fuel used. The present paper deals with the comparison of the level of combustion products of a spark ignition engine supplied by gasoline and by a mixture of 10 % ethanol - 90% gasoline.

  20. Mechanism and optimization of fuel injection parameters on combustion noise of DI diesel engine

    Institute of Scientific and Technical Information of China (English)

    张庆辉; 郝志勇; 郑旭; 杨文英; 毛杰

    2016-01-01

    Combustion noise takes large proportion in diesel engine noise and the studies of its influence factors play an important role in noise reduction. Engine noise and cylinder pressure measurement experiments were carried out. And the improved attenuation curves were obtained, by which the engine noise was predicted. The effect of fuel injection parameters in combustion noise was investigated during the combustion process. At last, the method combining single variable optimization and multivariate combination was introduced to online optimize the combustion noise. The results show that injection parameters can affect the cylinder pressure rise rate and heat release rate, and consequently affect the cylinder pressure load and pressure oscillation to influence the combustion noise. Among these parameters, main injection advance angle has the greatest influence on the combustion noise, while the pilot injection interval time takes the second place, and the pilot injection quantity is of minimal impact. After the optimal design of the combustion noise, the average sound pressure level of the engine is distinctly reduced by 1.0 dB(A) generally. Meanwhile, the power, emission and economy performances are ensured.

  1. CONCEPTION OF USE VIBROACOUSTIC SIGNALS AND NEURAL NETWORKS FOR DIAGNOSING OF CHOSEN ELEMENTS OF INTERNAL COMBUSTION ENGINES IN CAR VEHICLES

    Directory of Open Access Journals (Sweden)

    Piotr CZECH

    2014-03-01

    Full Text Available Currently used diagnostics systems are not always efficient and do not give straightforward results which allow for the assessment of the technological condition of the engine or for the identification of the possible damages in their early stages of development. Growing requirements concerning durability, reliability, reduction of costs to minimum and decrease of negative influence on the natural environment are the reasons why there is a need to acquire information about the technological condition of each of the elements of a vehicle during its exploitation. One of the possibilities to achieve information about technological condition of a vehicle are vibroacoustic phenomena. Symptoms of defects, achieved as a result of advanced methods of vibroacoustic signals processing can serve as models which can be used during construction of intelligent diagnostic system based on artificial neural networks. The work presents conception of use artificial neural networks in the task of combustion engines diagnosis.

  2. Construction of combustion models for rapeseed methyl ester bio-diesel fuel for internal combustion engine applications.

    Science.gov (United States)

    Golovitchev, Valeri I; Yang, Junfeng

    2009-01-01

    Bio-diesel fuels are non-petroleum-based diesel fuels consisting of long chain alkyl esters produced by the transesterification of vegetable oils, that are intended for use (neat or blended with conventional fuels) in unmodified diesel engines. There have been few reports of studies proposing theoretical models for bio-diesel combustion simulations. In this study, we developed combustion models based on ones developed previously. We compiled the liquid fuel properties, and the existing detailed mechanism of methyl butanoate ester (MB, C(5)H(10)O(2)) oxidation was supplemented by sub-mechanisms for two proposed fuel constituent components, C(7)H(16) and C(7)H(8)O (and then, by mp2d, C(4)H(6)O(2) and propyne, C(3)H(4)) to represent the combustion model for rapeseed methyl ester described by the chemical formula, C(19)H(34)O(2) (or C(19)H(36)O(2)). The main fuel vapor thermal properties were taken as those of methyl palmitate C(19)H(36)O(2) in the NASA polynomial form of the Burcat database. The special global reaction was introduced to "crack" the main fuel into its constituent components. This general reaction included 309 species and 1472 reactions, including soot and NO(x) formation processes. The detailed combustion mechanism was validated using shock-tube ignition-delay data under diesel engine conditions. For constant volume and diesel engine (Volvo D12C) combustion modeling, this mechanism could be reduced to 88 species participating in 363 reactions.

  3. Qualification of numerical software. Application to a Software for analyzing combustion in spark-ignition engines

    Energy Technology Data Exchange (ETDEWEB)

    Guilain, S. (Agence de l' Environnement et de la Maitrise de l' Energie, 75 - Paris (France) Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France) Ecole Nationale Superieure du Petrole et des Moteurs (ENSPM), 92 - Rueil-Malmaison (France)); Vignes, J. (Paris-6 Univ., 75 (France) Institut Francais du Petrole (IFP), 92 - Rueil-Malmaison (France))

    For analyzing physical phenomena, numerical simulation is used more and more frequently. Starting with a mathematical model describing the phenomenon being analyzed, this simulation consists in creating a scientific computing program expressing this model by implementing the numerical methods required for solving it. Simulation is considered to be valid when the results its provides are in agreement with the results issuing from experimenting with the phenomenon. However, these results contain a computing error resulting from the propagation of round-off errors caused by the floating-point arithmetic used by the computer. They also contain an error coming from the uncertainties concerning the data of the problem. The first part of this paper concerns the validation of numerical software results. After making a brief review of the floating-point arithmetic and highlighting the serious consequences it may have on the results obtained, a probabilistic approach to the analysis of round-off errors, the CESTAC (Controle et Estimation STochastique des Arrondis de Calculs) method, from the standpoint of both its theoretical bases and its practical implementation is described. The second part is devoted to the use of the CADNA software (Control of Accuracy and Debugging for Numerical Applications) for qualifying the simulation software, ANALCO (ANALyse de COmbustion) which analyses combustion in spark-ignition engines. After a description of the normal model of the phenomenon being analyzed and after mathematical model has been deduced, the ANALCO simulation software is described. The results obtained with ANALCO, not using CADNA, reveal the disagreement between the simulation results and the experimental results. The use of the CADNA software eliminates the numerical instabilities and demonstrates that the disagreement between the simulation results and the results observed is due only to numerical problems. (author). 22 refs., 21 figs., 10 tabs.

  4. Research on EHN additive on the diesel engine combustion characteristics in plateau environment

    Science.gov (United States)

    Sun, Zhixin; Li, Ruoting; Wang, Xiancheng; Hu, Chuan

    2017-03-01

    Aiming at the combustion deterioration problem of diesel engine in plateau environment, a bench test was carried out for the effects of EHN additive on combustion characteristics of the diesel engine with intake pressure of 0.68 kPa. Test results showed that with the full load working condition of 1 400 r/min: Cylinder pressure and pressure uprising rate decreased with EHN additive added in, mechanical load on the engine could be relieved; peak value of the heat release rate decreased and its occurrence advanced, ignition delay and combustion duration were shortened; cylinder temperature and exhaust gas temperature declined, thermal load on the engine could be relieved, output torque increased while specific oil consumption decreased, and effective thermal efficiency of diesel engine increased.

  5. Acoustic measurements for the combustion diagnosis of diesel engines fuelled with biodiesels

    Science.gov (United States)

    Zhen, Dong; Wang, Tie; Gu, Fengshou; Tesfa, Belachew; Ball, Andrew

    2013-05-01

    In this paper, an experimental investigation was carried out on the combustion process of a compression ignition (CI) engine running with biodiesel blends under steady state operating conditions. The effects of biodiesel on the combustion process and engine dynamics were analysed for non-intrusive combustion diagnosis based on a four-cylinder, four-stroke, direct injection and turbocharged diesel engine. The signals of vibration, acoustic and in-cylinder pressure were measured simultaneously to find their inter-connection for diagnostic feature extraction. It was found that the sound energy level increases with the increase of engine load and speed, and the sound characteristics are closely correlated with the variation of in-cylinder pressure and combustion process. The continuous wavelet transform (CWT) was employed to analyse the non-stationary nature of engine noise in a higher frequency range. Before the wavelet analysis, time synchronous average (TSA) was used to enhance the signal-to-noise ratio (SNR) of the acoustic signal by suppressing the components which are asynchronous. Based on the root mean square (RMS) values of CWT coefficients, the effects of biodiesel fractions and operating conditions (speed and load) on combustion process and engine dynamics were investigated. The result leads to the potential of airborne acoustic measurements and analysis for engine condition monitoring and fuel quality evaluation.

  6. Modeling of Transient Heat Flux in Spark Ignition Engine During Combustion and Comparisons with Experiment

    Directory of Open Access Journals (Sweden)

    T. F. Yusaf

    2005-01-01

    Full Text Available A quasi-one dimensional engine cycle simulation program was developed to predict the transient heat flux during combustion in a spark ignition engine. A two-zone heat release model was utilized to model the combustion process inside the combustion chamber. The fuel, air and burned gas properties throughout the engine cycle were calculated using variable specific heats. The transient heat flux inside the combustion chamber due to the change in the in-cylinder gas temperature and pressure during combustion was determined using the Woschni heat transfer model. The program was written in MATLAB together with the Graphical User Interface (GUI. Numerical results were compared with the experimental measurements and good agreement was obtained. Four thermocouples were used and positioned equi-spaced at 5mm intervals along a ray from the spark plug location on the engine head. These thermocouples were able to capture the heat flux release by the burned gas to the wall during the combustion process including the cycle-to-cycle variations. Pressure sensor was installed at the engine head to capture the pressure change throughout the cycle.

  7. Simulation and experiment for oxygen-enriched combustion engine using liquid oxygen to solidify CO2

    Science.gov (United States)

    Liu, Yongfeng; Jia, Xiaoshe; Pei, Pucheng; Lu, Yong; Yi, Li; Shi, Yan

    2016-01-01

    For capturing and recycling of CO2 in the internal combustion engine, Rankle cycle engine can reduce the exhaust pollutants effectively under the condition of ensuring the engine thermal efficiency by using the techniques of spraying water in the cylinder and optimizing the ignition advance angle. However, due to the water spray nozzle need to be installed on the cylinder, which increases the cylinder head design difficulty and makes the combustion conditions become more complicated. In this paper, a new method is presented to carry out the closing inlet and exhaust system for internal combustion engines. The proposed new method uses liquid oxygen to solidify part of cooled CO2 from exhaust system into dry ice and the liquid oxygen turns into gas oxygen which is sent to inlet system. The other part of CO2 is sent to inlet system and mixed with oxygen, which can reduce the oxygen-enriched combustion detonation tendency and make combustion stable. Computing grid of the IP52FMI single-cylinder four-stroke gasoline-engine is established according to the actual shape of the combustion chamber using KIVA-3V program. The effects of exhaust gas recirculation (EGR) rate are analyzed on the temperatures, the pressures and the instantaneous heat release rates when the EGR rate is more than 8%. The possibility of enclosing intake and exhaust system for engine is verified. The carbon dioxide trapping device is designed and the IP52FMI engine is transformed and the CO2 capture experiment is carried out. The experimental results show that when the EGR rate is 36% for the optimum EGR rate. When the liquid oxygen of 35.80-437.40 g is imported into the device and last 1-20 min, respectively, 21.50-701.30 g dry ice is obtained. This research proposes a new design method which can capture CO2 for vehicular internal combustion engine.

  8. Operation Evaluation Method for Marine Turbine Combustion Engines in Terms of Energetics

    Directory of Open Access Journals (Sweden)

    Dzida Marek

    2016-12-01

    Full Text Available An evaluation proposal (quantitative determination of any combustion turbine engine operation has been presented, wherein the impact energy occurs at a given time due to Energy conversion. The fact has been taken into account that in this type of internal combustion engines the energy conversion occurs first in the combustion chambers and in the spaces between the blade of the turbine engine. It was assumed that in the combustion chambers occurs a conversion of chemical energy contained in the fuel-air mixture to the internal energy of the produced exhaust gases. This form of energy conversion has been called heat. It was also assumed that in the spaces between the blades of the rotor turbine, a replacement occurs of part of the internal energy of the exhaust gas, which is their thermal energy into kinetic energy conversion of its rotation. This form of energy conversion has been called the work. Operation of the combustion engine has been thus interpreted as a transmission of power receivers in a predetermined time when there the processing and transfer in the form (means of work and heat occurs. Valuing the operation of this type of internal combustion engines, proposed by the authors of this article, is to determine their operation using physical size, which has a numerical value and a unit of measurement called joule-second [joule x second]. Operation of the combustion turbine engine resulting in the performance of the turbine rotor work has been presented, taking into account the fact that the impeller shaft is connected to the receiver, which may be a generator (in the case of one-shaft engine or a propeller of the ship (in the case of two or three shaft engine.

  9. Method for operating a spark-ignition, direct-injection internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Narayanaswamy, Kushal; Koch, Calvin K.; Najt, Paul M.; Szekely, Jr., Gerald A.; Toner, Joel G.

    2015-06-02

    A spark-ignition, direct-injection internal combustion engine is coupled to an exhaust aftertreatment system including a three-way catalytic converter upstream of an NH3-SCR catalyst. A method for operating the engine includes operating the engine in a fuel cutoff mode and coincidentally executing a second fuel injection control scheme upon detecting an engine load that permits operation in the fuel cutoff mode.

  10. Thermodynamic efficiency of present types of internal combustion engines for aircraft

    Science.gov (United States)

    Lucke, Charles E

    1917-01-01

    Report presents requirements of internal combustion engines suitable for aircraft. Topics include: (1) service requirements for aeronautic engines - power versus weight, reliability, and adaptability factors, (2) general characteristics of present aero engines, (3) aero engine processes and functions of parts versus power-weight ratio, reliability, and adaptability factors, and (4) general arrangement, form, proportions, and materials of aero parts - power-weight ratio, reliability, and adaptability.

  11. Genetic Algorithm-Based Design Optimization of Electromagnetic Valve Actuators in Combustion Engines

    OpenAIRE

    Seung Hwan Lee; Hwa Cho Yi; Kyuyoung Han; Jin Ho Kim

    2015-01-01

    In this research, the design of a new electromagnetic engine valve in the limited space of combustion engine is optimized by multidisciplinary simulation using MATLAB and Maxwell. An electromagnetic engine valve actuator using a permanent magnet is a new actuator concept for overcoming the inherent drawbacks of the conventional solenoid-driven electromagnetic engine valve actuator, such as high power consumption and so on. This study aims to maximize the vibration frequency of the armature to...

  12. 3-D modeling of parietal liquid films in internal combustion engines; Modelisation tridimensionnelle des films liquides parietaux dans les moteurs a combustion interne

    Energy Technology Data Exchange (ETDEWEB)

    Foucart, H.

    1998-12-11

    To simulate the air-fuel mixing in the intake ports and cylinder of an internal combustion engines, a wall fuel liquid film model has been developed for integration in 3D CFD codes. Phenomena taken into account include wall film formation by an impinging spray without splashing effect, film transport such as governed by mass and momentum equations with hot wall effects, and evaporation considering energy equation with an analytical mass transfer formulation developed here. A continuous-fluid method is used to describe the wall film over a three dimensional complex surface. The basic approximation is that of a laminar incompressible boundary layer; the liquid film equations are written in an integral form and solved by a first-order ALE finite volume scheme; the equation system is closed without coefficient fitting requirements. The model has been implemented in a Multi-Block version of KIVA-II (KMB) and tested against problems having theoretical solutions. Then in a first step, it has been compared to the measurements obtained in a cylindrical pipe reproducing the main characteristics of SI engine intake pipe flow and in a second step, it has been compared to the Xiong experiment concerning the film evaporation on a hot wall. The film behaviour is satisfactory reproduced by the computations for a set of operating conditions. Finally, engine calculations were conducted showing the importance of including a liquid film model for the simulations. (author) 54 refs.

  13. Numerical Studies on Controlling Gaseous Fuel Combustion by Managing the Combustion Process of Diesel Pilot Dose in a Dual-Fuel Engine

    Directory of Open Access Journals (Sweden)

    Mikulski Maciej

    2015-06-01

    Full Text Available Protection of the environment and counteracting global warming require finding alternative sources of energy. One of the methods of generating energy from environmentally friendly sources is increasing the share of gaseous fuels in the total energy balance. The use of these fuels in compression-ignition (CI engines is difficult due to their relatively high autoignition temperature. One solution for using these fuels in CI engines is operating in a dualfuel mode, where the air and gas mixture is ignited with a liquid fuel dose. In this method, a series of relatively complex chemical processes occur in the engine's combustion chamber, related to the combustion of individual fuel fractions that interact with one another. Analysis of combustion of specific fuels in this type of fuel injection to the engine is difficult due to the fact that combustion of both fuel fractions takes place simultaneously. Simulation experiments can be used to analyse the impact of diesel fuel combustion on gaseous fuel combustion. In this paper, we discuss the results of simulation tests of combustion, based on the proprietary multiphase model of a dual-fuel engine. The results obtained from the simulation allow for analysis of the combustion process of individual fuels separately, which expands the knowledge obtained from experimental tests on the engine.

  14. A simple strategy to establish preliminary engine cylinder geometry for optimum combustion

    Energy Technology Data Exchange (ETDEWEB)

    Harish Kumar, R. [Sri Siddhartha Inst. of Technology, Karnataka (India); Antony, A.J. [Sahyadri Inst. of Technology, Mangalore, Karnataka (India)

    2009-07-01

    The design of modern spark ignition engines presents a challenge for automotive engineers in terms of striking the right combination of engine operating parameters and geometry. Most modern spark ignition engines have a compression ratio in the range 8 to 11 and the engine geometry is dictated by the choice of the bore/stroke (B/Ls) ratio in addition to various other design considerations such as the location and size of valves and location of spark plugs. Small engines generally have a B/Ls ratio ranging from 0.7 to 1.3 while large stationary engines have a ratio of less than 0.7. For a given displacement volume, a longer stroke allows for smaller bore which results in less surface area in the combustion chamber with a correspondingly smaller heat loss, which increases thermal efficiency within the combustion chamber. However the longer stroke results in higher piston speed and higher friction losses which reduces the brake power output of the engine. If the stroke is shortened, the bore must be increased which reduces the friction losses but increases the heat transfer losses. This paper presented a simple thermodynamics approach based on one dimensional thermodynamic model of the combustion chamber to establish the appropriate B/Ls ratio depending on the operating conditions of the engine such as its compression ratio, speed, and fuel equivalence ratios, in conjunction with a nearly full fledged simulation program for optimum combustion in spark ignition engines. The paper described the engine test rig as well as the experimental procedure. The development of the mathematical model was also explained. It was concluded that there is a significant relationship between the compression ratio of the engine and the B/Ls ratio. These valves must match for optimum combustion and optimum specific power output. 10 refs., 1 tab., 5 figs.

  15. 40 CFR 60.4203 - How long must my engines meet the emission standards if I am a stationary CI internal combustion...

    Science.gov (United States)

    2010-07-01

    ... emission standards if I am a stationary CI internal combustion engine manufacturer? 60.4203 Section 60.4203... Combustion Engines Emission Standards for Manufacturers § 60.4203 How long must my engines meet the emission standards if I am a stationary CI internal combustion engine manufacturer? Engines manufactured by...

  16. Cycle-to-cycle fluctuation of combustion in a spark-ignition engine; Hibana tenka engine no nensho hendo

    Energy Technology Data Exchange (ETDEWEB)

    Hamamoto, Y.; Yoshiyama, S.; Tomita, E.; Hamagami, T. [Okayama University, Okayama (Japan); Otsubo, H. [Yammer Diesel Engine Co. Ltd. Tokyo (Japan)

    1997-10-01

    In a homogeneous charge spark-ignition engine, the duration of early stage of combustion is a dominant factor for determining the fluctuation of mean effective pressure. And the early stage of combustion varies with the equivalence ratio and turbulence characteristics of the mixture. In this study, the fluctuations of 1% combustion duration and indicated mean effective pressure Pmi were computed as the function of fluctuations both in the equivalence ratio {phi} of the mixture and in the turbulence characteristics of the cylinder charge. And effects of the spark timing {theta}ig and {phi} on the cycle-to-cycle fluctuation in Pmi were investigated. 16 refs., 6 figs.

  17. Three-dimensional modeling of diesel engine intake flow, combustion and emissions

    Science.gov (United States)

    Reitz, R. D.; Rutland, C. J.

    1992-01-01

    A three-dimensional computer code (KIVA) is being modified to include state-of-the-art submodels for diesel engine flow and combustion: spray atomization, drop breakup/coalescence, multi-component fuel vaporization, spray/wall interaction, ignition and combustion, wall heat transfer, unburned HC and NOx formation, soot and radiation, and the intake flow process. Improved and/or new submodels which were completed are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NOx, and spray/wall impingement with rebounding and sliding drops. Results to date show that adding the effects of unsteadiness and compressibility improves the accuracy of heat transfer predictions; spray drop rebound can occur from walls at low impingement velocities (e.g., in cold-starting); larger spray drops are formed at the nozzle due to the influence of vaporization on the atomization process; a laminar-and-turbulent characteristic time combustion model has the flexibility to match measured engine combustion data over a wide range of operating conditions; and finally, the characteristic time combustion model can also be extended to allow predictions of ignition. The accuracy of the predictions is being assessed by comparisons with available measurements. Additional supporting experiments are also described briefly. To date, comparisons with measured engine cylinder pressure and heat flux data were made for homogeneous charge, spark-ignited and compression-ignited engines. The model results are in good agreement with the experiments.

  18. Investigation of a Spark Ignition Internal Combustion Engine via IR Spectroscopy

    Science.gov (United States)

    Sakai, Stephen; White, Allen R.; Gross, Kevin; Devasher, Rebecca B.

    2010-06-01

    Previous work has shown that the automotive fuel components of isopropanoland ethanol can be excited by a 10.2 um and 9.3 um CO2 lasers, respectively. Through the use of a monochromator and an indium antimonide detector, the decay time of the excited molecules was measured and found to be significantly long enough to allow for the possibility of experimentation in an internal combustion (IC) engine. In order to pursue In Situ measurements in an internal combustion engine, a MegaTech Mark III transparent engine was modified with a sapphire combustion chamber. This modification will allow the transmission of infrared radiation for time-resolved spectroscopic measurements by an infrared spectrometer. By using a Telops FIRST-MWE imaging Fourier transform spectrometer, temporally and spatially resolved infrared spectral data can be acquired and compared for combustion in the engine both with and without laser excitation. Measurements performed with system provide insight into the energy transfer vectors that precede combustion as well as provide an in situ measurement of the progress of combustion.

  19. Introductory statistics and random phenomena uncertainty, complexity and chaotic behavior in engineering and science

    CERN Document Server

    Denker, Manfred

    2017-01-01

    Introductory Statistics and Random Phenomena integrates traditional statistical data analysis with new computational experimentation capabilities and concepts of algorithmic complexity and chaotic behavior in nonlinear dynamic systems.  This was the first advanced text/reference to bring together such a comprehensive variety of tools for the study of random phenomena occurring in engineering and the natural, life, and social sciences. The crucial computer experiments are conducted using the readily available computer program Mathematica® Uncertain Virtual Worlds™ software packages which optimize and facilitate the simulation environment.  Brief tutorials are included that explain how to use theMathematica® programs for effective simulation and computer experiments.  Large and original real-life data sets are introduced and analyzed as a model for independent study. This is an excellent classroom tool and self-study guide.  The material is presented in a clear and accessible style providing numerous...

  20. 40 CFR Appendix A to Subpart A of... - State Regulation of Nonroad Internal Combustion Engines

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 20 2010-07-01 2010-07-01 false State Regulation of Nonroad Internal Combustion Engines A Appendix A to Subpart A of Part 89 Protection of Environment ENVIRONMENTAL PROTECTION...-IGNITION ENGINES General Pt. 89, Subpt. A, App. A Appendix A to Subpart A of Part 89—State Regulation...

  1. IDEALIZED ENGINE EMISSIONS RESULTING FROM THE COMBUSTION OF GASOLINE SUPPLEMENTED WITH LPG

    Directory of Open Access Journals (Sweden)

    Cenk SAYIN

    2006-02-01

    Full Text Available In the internal combustion engines, the studies to reduce brake specific fuel consumption and exhaust emissions to the lowest level are the start of the investigations on the dual fuel engines. In this study, the changes in the exhaust emissions of the dual fuel (gasoline + LPG at different ratios have been calculated using a computer program and the results are discussed.

  2. Internal combustion engines: Computer applications. (Latest citations from the EI Compendex plus database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    1993-10-01

    The bibliography contains citations concerning the application of computers and computerized simulations in the design, analysis, operation, and evaluation of various types of internal combustion engines and associated components and apparatus. Special attention is given to engine control and performance. (Contains a minimum of 67 citations and includes a subject term index and title list.)

  3. Multi-dimensional modeling of the application of catalytic combustion to homogeneous charge compression ignition engine

    Science.gov (United States)

    Zeng, Wen; Xie, Maozhao

    2006-12-01

    The detailed surface reaction mechanism of methane on rhodium catalyst was analyzed. Comparisons between numerical simulation and experiments showed a basic agreement. The combustion process of homogeneous charge compression ignition (HCCI) engine whose piston surface has been coated with catalyst (rhodium and platinum) was numerically investigated. A multi-dimensional model with detailed chemical kinetics was built. The effects of catalytic combustion on the ignition timing, the temperature and CO concentration fields, and HC, CO and NOx emissions of the HCCI engine were discussed. The results showed the ignition timing of the HCCI engine was advanced and the emissions of HC and CO were decreased by the catalysis.

  4. Diesel-Minimal Combustion Control of a Natural Gas-Diesel Engine

    Directory of Open Access Journals (Sweden)

    Florian Zurbriggen

    2016-01-01

    Full Text Available This paper investigates the combustion phasing control of natural gas-diesel engines. In this study, the combustion phasing is influenced by manipulating the start and the duration of the diesel injection. Instead of using both degrees of freedom to control the center of combustion only, we propose a method that simultaneously controls the combustion phasing and minimizes the amount of diesel used. Minimizing the amount of diesel while keeping the center of combustion at a constant value is formulated as an optimization problem with an equality constraint. A combination of feedback control and extremum seeking is used to solve this optimization problem online. The necessity to separate the different time scales is discussed and a structure is proposed that facilitates this separation for this specific example. The proposed method is validated by experiments on a test bench.

  5. Fuel/oxidizer-rich high-pressure preburners. [staged-combustion rocket engine

    Science.gov (United States)

    Schoenman, L.

    1981-01-01

    The analyses, designs, fabrication, and cold-flow acceptance testing of LOX/RP-1 preburner components required for a high-pressure staged-combustion rocket engine are discussed. Separate designs of injectors, combustion chambers, turbine simulators, and hot-gas mixing devices are provided for fuel-rich and oxidizer-rich operation. The fuel-rich design addresses the problem of non-equilibrium LOX/RP-1 combustion. The development and use of a pseudo-kinetic combustion model for predicting operating efficiency, physical properties of the combustion products, and the potential for generating solid carbon is presented. The oxygen-rich design addresses the design criteria for the prevention of metal ignition. This is accomplished by the selection of materials and the generation of well-mixed gases. The combining of unique propellant injector element designs with secondary mixing devices is predicted to be the best approach.

  6. Ceramic-coated components for the combustion zone of natural gas engines

    Science.gov (United States)

    Holloman, L.; Levy, A. V.

    1992-03-01

    The use of ceramic coatings on the combustion zone surfaces of large,natural gas-fueled,internal com-bustion engines is discussed. Unique handling and quality control systems are required for plasma spray-ing thin (0.25 mm,0.0010) in.coatings on up to 48.25(cm19)-in.diameter piston crowns and cylinder heads weighing up to(1200 lb).The in-service performance characteristics of two types of natural gas-fu-eled combustion engines powering natural gas compressors that had thin zirconia ceramic coatings ap-plied to their combustion zone surfaces are presented. Their performance was measured in the field be-fore and after coating. It was determined that the durability,power output,fuel consumption,exhaust emissions,and other operating characteristics all improved due to ceramic coating of the flame side sur-faces of cylinder heads,power pistons,and valves.

  7. Device to lower NOx in a gas turbine engine combustion system

    Science.gov (United States)

    Laster, Walter R; Schilp, Reinhard; Wiebe, David J

    2015-02-24

    An emissions control system for a gas turbine engine including a flow-directing structure (24) that delivers combustion gases (22) from a burner (32) to a turbine. The emissions control system includes: a conduit (48) configured to establish fluid communication between compressed air (22) and the combustion gases within the flow-directing structure (24). The compressed air (22) is disposed at a location upstream of a combustor head-end and exhibits an intermediate static pressure less than a static pressure of the combustion gases within the combustor (14). During operation of the gas turbine engine a pressure difference between the intermediate static pressure and a static pressure of the combustion gases within the flow-directing structure (24) is effective to generate a fluid flow through the conduit (48).

  8. Numerical study of premixed HCCI engine combustion and its sensitivity to computational mesh and model uncertainties

    Science.gov (United States)

    Kong, Song-Charng; Reitz, Rolf D.

    2003-06-01

    This study used a numerical model to investigate the combustion process in a premixed iso-octane homogeneous charge compression ignition (HCCI) engine. The engine was a supercharged Cummins C engine operated under HCCI conditions. The CHEMKIN code was implemented into an updated KIVA-3V code so that the combustion could be modelled using detailed chemistry in the context of engine CFD simulations. The model was able to accurately simulate the ignition timing and combustion phasing for various engine conditions. The unburned hydrocarbon emissions were also well predicted while the carbon monoxide emissions were under predicted. Model results showed that the majority of unburned hydrocarbon is located in the piston-ring crevice region and the carbon monoxide resides in the vicinity of the cylinder walls. A sensitivity study of the computational grid resolution indicated that the combustion predictions were relatively insensitive to the grid density. However, the piston-ring crevice region needed to be simulated with high resolution to obtain accurate emissions predictions. The model results also indicated that HCCI combustion and emissions are very sensitive to the initial mixture temperature. The computations also show that the carbon monoxide emissions prediction can be significantly improved by modifying a key oxidation reaction rate constant.

  9. Cyclic Combustion Variations in Dual Fuel Partially Premixed Pilot-Ignited Natural Gas Engines

    Energy Technology Data Exchange (ETDEWEB)

    Srinivasan, K. K. [Mississippi State Univ., MS (United States). Dept. of Mechanical Engineering; Krishnan, S. R. [Mississippi State Univ., MS (United States). Dept. of Mechanical Engineering; Qi, Y. [Caterpillar, Inc., Peoria, IL (United States)

    2012-05-09

    Dual fuel pilot ignited natural gas engines are identified as an efficient and viable alternative to conventional diesel engines. This paper examines cyclic combustion fluctuations in conventional dual fuel and in dual fuel partially premixed low temperature combustion (LTC). Conventional dual fueling with 95% (energy basis) natural gas (NG) substitution reduces NOx emissions by almost 90%t relative to straight diesel operation; however, this is accompanied by 98% increase in HC emissions, 10 percentage points reduction in fuel conversion efficiency (FCE) and 12 percentage points increase in COVimep. Dual fuel LTC is achieved by injection of a small amount of diesel fuel (2-3 percent on an energy basis) to ignite a premixed natural gas₋air mixture to attain very low NOx emissions (less than 0.2 g/kWh). Cyclic variations in both combustion modes were analyzed by observing the cyclic fluctuations in start of combustion (SOC), peak cylinder pressures (Pmax), combustion phasing (Ca50), and the separation between the diesel injection event and Ca50 (termed "relative combustion phasing" ). For conventional dual fueling, as % NG increases, Pmax decreases, SOC and Ca50 are delayed, and cyclic variations increase. For dual fuel LTC, as diesel injection timing is advanced from 20° to 60° BTDC, the relative combustion phasing is identified as an important combustion parameter along with SoC, Pmax, and CaPmax. For both combustion modes, cyclic variations were characterized by alternating slow and fast burn cycles, especially at high %NG and advanced injection timings. Finally, heat release return maps were analyzed to demonstrate thermal management strategies as an effective tool to mitigate cyclic combustion variations, especially in dual fuel LTC.

  10. Efficiency characteristics of a new quasi-constant volume combustion spark ignition engine

    Directory of Open Access Journals (Sweden)

    Dorić Jovan Ž.

    2013-01-01

    Full Text Available A zero dimensional model has been used to investigate the combustion performance of a four cylinder petrol engine with unconventional piston motion. The main feature of this new spark ignition (SI engine concept is the realization of quasi-constant volume (QCV during combustion process. Presented mechanism is designed to obtain a specific motion law which provides better fuel consumption of internal combustion (IC engines. These advantages over standard engine are achieved through synthesis of unconventional piston mechanism. The numerical calculation was performed for several cases of different piston mechanism parameters, compression ratio and engine speed. Calculated efficiency and power diagrams are plotted and compared with performance of ordinary SI engine. The results show that combustion during quasi-constant volume has significant impact on improvement of efficiency. The main aim of this paper is to find a proper kinematics parameter of unconventional piston mechanism for most efficient heat addition in SI engines.[Acknowledgment. This research was done as a part of project TR31046 "Improvement of the quality of tractors and mobile systems with the aim of increasing competitiveness and preserving soil and environment", supported by Serbian Ministry of Science and Technological Development.

  11. Analysis of an Internal Combustion Engine Using Porous Foams for Thermal Energy Recovery

    Directory of Open Access Journals (Sweden)

    Mehdi Ali Ehyaei

    2016-03-01

    Full Text Available Homogeneous and complete combustion in internal combustion engines is advantageous. The use of a porous foam in the exhaust gas in an engine cylinder for heat recovery is examined here with the aim of reducing engine emissions. The internal combustion engine with a porous core regenerator is modeled using SOPHT software, which solved the differential equations for the thermal circuit in the engine. The engine thermal efficiency is observed to increase from 43% to 53% when the porous core regenerator is applied. Further, raising the compression ratio causes the peak pressure and thermal efficiency to increase, e.g., increasing the compression ratio from 13 to 15 causes the thermal efficiency and output work to increase from 53% to 55% and from 4.86 to 4.93 kJ, respectively. The regenerator can also be used as a catalytic converter for fine particles and some other emissions. The regenerator oxidizes unburned hydrocarbons. Meanwhile, heat recovered from the exhaust gases can reduce fuel consumption, further reducing pollutant emissions from the internal combustion engine.

  12. Estimation of the combustion-related noise transfer matrix of a multi-cylinder diesel engine

    Science.gov (United States)

    Lee, Moohyung; Bolton, J. Stuart; Suh, Sanghoon

    2009-01-01

    In the present paper, a procedure for estimating an engine-platform-dependent transfer matrix that relates in-cylinder pressures to radiated noise resulting from processes associated with the combustion process is described. A knowledge of that transfer matrix allows the combustion-related component of the noise radiated by a diesel engine to be estimated from a knowledge of cylinder pressure signals. The procedure makes use of multi-input/multi-output (MIMO) system modeling concepts in conjunction with cross-spectral measurements. To date, the empirical prediction of diesel engine combustion noise has usually been achieved by combining a cylinder pressure with a single, smooth structural attenuation function (e.g., the Lucas combustion noise meter) regardless of the specifications of the engine. In comparison, the procedure described in the present work provides the structural attenuation characteristics of a particular engine in the form of a transfer matrix, thus allowing accurate prediction by accounting fully for inter-cylinder correlation, cylinder-to-cylinder variation and the detailed characteristics of an engine structure. The procedure was applied to a six-cylinder diesel engine, and the various aspects of the new procedure are described.

  13. Fuel injection for internal combustion engines. (Latest citations from the NTIS bibliographic database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The bibliography contains citations concerning research and development of fuel injection systems applied to internal combustion engines and turbines. Gasoline, diesel, synthetic fuels, and liquid gas systems are discussed relative to systems` variations and performances. Fuel injection atomization and combustion are considered in theory, and fuel injection relative to emission control is included.(Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

  14. Fuel injection for internal combustion engines. (Latest citations from the NTIS Bibliographic database). Published Search

    Energy Technology Data Exchange (ETDEWEB)

    1993-09-01

    The bibliography contains citations concerning research and development of fuel injection systems applied to internal combustion engines and turbines. Gasoline, diesel, synthetic fuels, and liquid gas systems are discussed relative to systems' variations and performances. Fuel injection atomization and combustion are considered in theory, and fuel injection relative to emission control is included. (Contains a minimum of 223 citations and includes a subject term index and title list.)

  15. Multidimensional Modeling of Fuel Composition Effects on Combustion and Cold-starting in Diesel Engines

    Science.gov (United States)

    1995-01-01

    equally important for both the gas and liquid phase. For the gas phase, a modified Redlich - Kwong equation of state is used (Prausnitz, [lo]). In the...residual fuel mass (case 9). Ignition started early but the combustion developed at a slower rate. Another application of an altered engine geometry...Power, Vol. 115, pp. 781-789,1993. 17. Kong, S.C., Han, Z., and Reitz, R.D., “The Development and Application of a Diesel Ignition and Combustion

  16. Combustion Property Analysis and Control System for the Dynamics of a Single Cylinder Diesel Engine

    Directory of Open Access Journals (Sweden)

    Bambang Wahono

    2013-12-01

    Full Text Available Corresponding to global environment problems in recent year, the technology for reducing fuel consumption and exhaust gas emission of engine was needed. Simulation of transient engine response is needed to predict engine performance that frequently experience rapid changes of speed. The aim of this research is to develop a non-linear dynamic control model for direct injection single cylinder diesel engine which can simulate engine performance under transient conditions. In this paper, the combustion model with multistage injection and conducted experiments in the transient conditions to clarify the combustion characteristics was proposed. In order to perform the analysis of acceleration operation characteristics, it was built a Model Predictive Control (MPC to reproduce the characteristic values of the exhaust gas and fuel consumption from the control parameters in particular. Finally, MPC is an effective method to perform the analysis of characteristic in diesel engine under transient conditions.

  17. Emission and Combustion Characteristics of Si Engine Working Under Gasoline Blended with Ethanol Oxygenated Organic Compounds

    Directory of Open Access Journals (Sweden)

    Dhanapal Balaji

    2010-01-01

    Full Text Available Problem statement: The objective of this study is to investigate the effect of using unleaded gasoline and additives blends on Spark Ignition engine (SI engine combustion and exhaust emission. Approach: A four stroke, single cylinder SI engine was used for conducting this study. Exhaust emissions were analysed for Carbon Monoxide (CO, Hydrocarbon (HC and Oxides of Nitrogen (NOx and carbon dioxide (CO2 using unleaded gasoline and additives blends with different percentages of fuel at varying engine torque condition and constant engine speed. Results: The result showed that the blending of unleaded gasoline increases the octane number and power output this may leads to increase the brake thermal efficiency. The CO, HC and NOx emissions concentrations in the engine exhaust decreases while the CO2 concentration increases. Conclusion: Using ethanol as a fuel additive to unleaded gasoline causes an improvement in combustion characteristics and significant reduction in exhaust emissions.

  18. FUEL EFFECTS ON COMBUSTION WITH EGR DILUTION IN SPARK IGNITED ENGINES

    Energy Technology Data Exchange (ETDEWEB)

    Szybist, James P [ORNL

    2016-01-01

    The use of EGR as a diluent allows operation with an overall stoichiometric charge composition, and the addition of cooled EGR results in well-understood thermodynamic benefits for improved fuel consumption. This study investigates the effect of fuel on the combustion and emission response of EGR dilution in spark ignited engines. A 2.0 L GM Ecotec LNF engine equipped with the production side-mounted direct injection (DI) fueling system is used in this study. Ethanol, isooctane and certified gasoline are investigated with EGR from 0% to the EGR dilution tolerance. Constant BMEP at 2000 rpm was operated with varying CA50 from 8 CAD to 16 CAD aTDCf. The results show that ethanol gives the largest EGR tolerance at a given combustion phasing, engine load and speed. The improved EGR dilution tolerance with ethanol is attributed to a faster flame speed, which manifests itself as shorter combustion duration. Data shows that the combustion stability limit occurs at a critical combustion duration that is fuel independent. Due to different flame speeds, this critical combustion duration occurs at different EGR levels for the different fuels.

  19. The combustion system of the MAN 20V35/44G gas engine

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, Markus; Auer, Matthias; Stiesch, Gunnnar [MAN Diesel and Turbo SE, Augsburg (Germany)

    2013-05-15

    The new gas engine 20V35/44G by MAN Diesel and Turbo SE has a power output of 10.6 MW. The high effective efficiency level of 48.4 % as well as numerous technical innovations allow an environmentally-friendly, economical and reliable engine operation. Key to achieve this is the combustion system, which has been optimised during advanced engineering by means of modern simulation tools and extensive single-cylinder tests. (orig.)

  20. Miniature Internal Combustion Engine-Generator for High Energy Density Portable Power

    Science.gov (United States)

    2008-12-01

    very effective at maintaining a constant voltage and stroke as the HCCI combustion pressure varies during engine warmup. The current is modulated by the...Comparison of Measured and Predicted Two- Stroke Engine Power Output for Jet-A and Propane 5 The exhaust emissions of the 300 W MICE generator with HCCI ...1 Two-Stroke Engine Double- Helix Spring Linear Alternator Magnet Pole Permanent Magnet Alternator Coil Spring Casing Coil Standoff Double-Helix

  1. Development of Kinetic Mechanisms for Next-Generation Fuels and CFD Simulation of Advanced Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Pitz, William J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McNenly, Matt J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Whitesides, Russell [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mehl, Marco [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Killingsworth, Nick J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Westbrook, Charles K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-12-17

    Predictive chemical kinetic models are needed to represent next-generation fuel components and their mixtures with conventional gasoline and diesel fuels. These kinetic models will allow the prediction of the effect of alternative fuel blends in CFD simulations of advanced spark-ignition and compression-ignition engines. Enabled by kinetic models, CFD simulations can be used to optimize fuel formulations for advanced combustion engines so that maximum engine efficiency, fossil fuel displacement goals, and low pollutant emission goals can be achieved.

  2. Method and systems for power control of internal combustion engines using individual cycle cut-off

    Energy Technology Data Exchange (ETDEWEB)

    Fedorenko, Y.; Korzhov, M.; Filippov, A.; Atamanenko, N.

    1996-09-01

    A new method of controlling power has been developed for improving efficiency and emissions performance of internal combustion engines at partial load. The method involves cutting-off some of the work cycles, as the load decreases, to obtain required power. Theoretical and experimental material is presented to illustrate the underlying principle, the implementation means and the results for the 4- and 8-cylinder piston engine and a twin rotor Wankel engine applications.

  3. Combustion and Vibration Analysis of Idi- Diesel Engine Fuelled With Neat Preheated Jatropha Methyl Ester

    Directory of Open Access Journals (Sweden)

    Y.Ashok Kumar Reddy

    2014-03-01

    Full Text Available Experimentation is conducted on an IDI diesel engine and the results of combustion and vibration on IDI -Diesel engine fueled with the preheated Jatropha Methyl Ester (JME are presented. The Present research trend is to replace conventional diesel by renewable alternative fuels in view of fast depletion of petroleum reserves and to reduce the exhaust emissions from the engines without altering the basic design of the engine. Due to moderately higher viscosity effects, the direct use of biodiesel in C.I. engines is limited to 20% and the limitation is based on the NO emission also. In this work, the biodiesel is preheated using on line electronically controlled electrical preheating system before it enters into the injector. Experiments are conducted on a four stroke single cylinder IDI engine to find combustion and vibration characteristics of the engine with the preheated Jatropha Methyl Ester (JME heated to temperatures viz. 60,70,80,90 and 1000C. Normally thin oils due to heating may trigger fast burning leading to either detonation or knocking of the engine. This can be predicted by recording vibration on the cylinder head in different directions. The cylinder vibrations in the form of FFT and time waves have been analyzed to estimate the combustion propensity. Experiments are done using diesel, biodiesel and biodiesel at different preheated temperatures and for different engine loading conditions keeping the speed constant at 1500 rpm. Biodiesel preheated to 600C proved encouraging in all respects.

  4. Application of neural network in the study of combustion rate of natural gas/diesel dual fuel engine.

    Science.gov (United States)

    Yan, Zhao-Da; Zhou, Chong-Guang; Su, Shi-Chuan; Liu, Zhen-Tao; Wang, Xi-Zhen

    2003-01-01

    In order to predict and improve the performance of natural gas/diesel dual fuel engine (DFE), a combustion rate model based on forward neural network was built to study the combustion process of the DFE. The effect of the operating parameters on combustion rate was also studied by means of this model. The study showed that the predicted results were good agreement with the experimental data. It was proved that the developed combustion rate model could be used to successfully predict and optimize the combustion process of dual fuel engine.

  5. Application of neural network in the study of combustion rate of natural gas/diesel dual fuel engine

    Institute of Scientific and Technical Information of China (English)

    严兆大; 周重光; 苏石川; 刘震涛; 王希珍

    2003-01-01

    In order to predict and improve the performance of natural gas/diesel dual fuel engine (DFE), a combustion rate model based on forward neural network was built to study the combustion process of the DFE. The effect of the operating parameters on combustion rate was also studied by means of this model. The study showed that the predicted results were good agreement with the experimental data. It was proved that the developed combustion rate model could be used to successfully predict and optimize the combustion process of dual fuel engine.

  6. Application of neural network in the study of combustion rate of natural gas/diesel dual fuel engine

    Institute of Scientific and Technical Information of China (English)

    严兆大; 周重光; 苏石川; 刘震涛; 王希珍

    2003-01-01

    In order to predict and improve the performance of matural gas/diesel dual fuel engine(DFE),a combustion rate model based on forward meural network was built to study the combustion process of the DFE.The effect of the operating parameters on combustion rate was also studied by means of this model.The study showed that the predicted results were good agreement with the experimental data.It was proved that the de-veloped combustion rate model could be used to successfully predict and optimize the combustion process of dual fuel engine.

  7. Combustion characteristics of SI engine fueled with methanol-gasoline blends during cold start

    Institute of Scientific and Technical Information of China (English)

    Ruizhi SONG; Tiegang HU; Shenghua LIU; Xiaoqiang LIANG

    2008-01-01

    A 3-cylinder port fuel injection (PFI) engine fueled with methanol-gasoline blends was used to study combustion and emission characteristics. Cylinder pres-sure analysis indicates that engine combustion is improved when methanol is added to gasoline. With the increase of methanol, the flame developing period and the rapid combustion period are shortened, and the indicated mean effective pressure increases during the first 50 cycles. Meanwhile, a novel quasi-instantaneous sampling system was designed to measure engine emissions during cold start and warm-up. The results at 5℃ show that unburned hydrocarbon (UHC) and carbon monoxide (CO) decrease remarkably. Hydrocarbon (HC) reduces by 40% and CO by 70% when fueled with M30 (30% methanol in volume). The exhaust gas temperature is about 140℃ higher at 200 s after operation compared with that of gasoline.

  8. The Influence of Hydrogen Gas on the Measures of Efficiency of Diesel Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Jurgis Latakas

    2014-12-01

    Full Text Available In this research paper energy and ecological parameters of diesel engine which works under addition of hydrogen (10, 20, 30 l/ min are presented. A survey of research literature has shown that addition of hydrogen gases improve diesel combustion; increase indicated pressure; decrease concentration of carbon dioxide (CO2, hydrocarbons (HC, particles; decrease fuel consumptions. Results of the experiment revealed that hydrogen gas additive decreased pressure in cylinder in kinetic combustion phase. Concentration of CO2 and nitrous oxides (NOx decreased not significantly, HC – increased. Concentration of particles in engine exhaust gases significantly decreased. In case when hydrogen gas as additive was supplied, the fuel consumptions decreased a little. Using AVL BOOST software combustion process analysis was made. It was determined that in order to optimize engine work process under hydrogen additive usage, it is necessary to adjust diesel injection angle.

  9. Simulation Analysis of Combustion Parameters and Emission Characteristics of CNG Fueled HCCI Engine

    Directory of Open Access Journals (Sweden)

    P. M. Diaz

    2013-01-01

    Full Text Available The naturally aspirated compressed natural gas (CNG fueled homogeneous charge compression ignition (HCCI engine operation region is narrow between heavy knock at rich air-fuel mixture side and misfire at the lean air-fuel mixture side. However, high activation energy is needed to attain autoignition temperature of CNG fueled HCCI engine. This paper seeks to provide guidance in overcoming challenges of CNG fueled HCCI engine by using CHEMKIN. It is used to investigate the fundamental characteristics of the homogeneous charge compression ignition combustion process for different air-fuel mixture inlet temperature, relative air-fuel ratio of 2.5, and with hemispherical bowl types of combustion chambers. The variation of various properties like the peak cylinder pressure, peak cylinder temperature, CO emission, NO emission, soot emission, and HC emission are studied. It is necessary to develop new combustion models to simulate and predict all parameters with high accuracy.

  10. Quasi-Dimensional Modeling of a CNG Fueled HCCI Engine Combustion Using Detailed Chemical Kinetic

    Directory of Open Access Journals (Sweden)

    Younes Bakhshan

    2013-01-01

    Full Text Available In this study, an in-house quasi dimensional code has been developed which simulates the intake, compression, combustion, expansion and exhaust strokes of a homogeneous charge compression ignition (HCCI engine. The compressed natural gas (CNG has been used as fuel. A detailed chemical kinetic scheme constituting of 310 and 1701 elementary equations developed by Bakhshan et al. has been applied for combustion modeling and heat release calculations. The zero-dimensional k-ε turbulence model has been used for calculation of heat transfer. The output results are the performance and pollutants emission and combustion characteristics in HCCI engines. Parametric studies have been conducted to discussing the effects of various parameters on performance and pollutants emission of these engines.

  11. INFLUENCE OF SWIRL ON SPRAY CHARACTERISTICS AND COMBUSTION, A NUMERICAL INVESTIGATION OF A CATERPILLER DIESEL ENGINE

    Directory of Open Access Journals (Sweden)

    M. SREENIVASULU

    2012-10-01

    Full Text Available The purpose of this study is to find the appropriate swirl ratio at which a DI diesel engine should be operated. In the process of identifying an appropriate swirl, the combustion behaviour was analysed by considering Pressure variations and Heat Release Rate variations against crank angle. The spray characteristics were also analysed by considering Penetration lengths, Sauter mean diameters, Spray cone angles against crank angle. Final conclusions were derived by considering NOx emission levels. A turbo charged DI diesel engine geometry was considered for the analysis. Proper care was taken inidentifying the range of Swirl Ratios. A 3-dimensional CFD code (RECARDO VECTIS, which is capable of solving 3-dimensional unsteady, turbulent flows, sprays and combustion of IC engines was used. In the first step CFD code was validated by comparing the obtained results with the experimental results. In the next step an attempt was made to study the influence of swirl on the spray characteristics and combustion.

  12. Internal combustion engine system having a power turbine with a broad efficiency range

    Science.gov (United States)

    Whiting, Todd Mathew; Vuk, Carl Thomas

    2010-04-13

    An engine system incorporating an air breathing, reciprocating internal combustion engine having an inlet for air and an exhaust for products of combustion. A centripetal turbine receives products of the combustion and has a housing in which a turbine wheel is rotatable. The housing has first and second passages leading from the inlet to discrete, approximately 180.degree., portions of the circumference of the turbine wheel. The passages have fixed vanes adjacent the periphery of the turbine wheel and the angle of the vanes in one of the passages is different than those in the other so as to accommodate different power levels providing optimum approach angles between the gases passing the vanes and the blades of the turbine wheel. Flow through the passages is controlled by a flapper valve to direct it to one or the other or both passages depending upon the load factor for the engine.

  13. NUMERICAL STUDIES ON HYDROGEN COMBUSTION IN A FILM COOLED CRYOGENIC ROCKET ENGINE

    Directory of Open Access Journals (Sweden)

    ARSHAD A.

    2012-07-01

    Full Text Available Liquid rocket engines have variety of propellant combinations which produces very high specific impulses. It is due to this fact; very high heat fluxes are incident on the combustion chamber and the nozzle walls. In order to deal with these heat fluxes, a wide range of cooling techniques have been employed, out of which a combination of film cooling and regenerative cooling promises to be the most effective one. The present study involves the numerical analysis of combustion in a typical film cooled cryogenic rocket engine thrust chamber considering the combustion of the fuel, heat transfer through the chamber walls and the fluid flow simultaneously. Analysis was done for a typical rocket engine thrust chamber with a single coaxial injector which uses gaseous hydrogen as the fuel and liquid oxygen as the oxidizer.

  14. A Mixing Based Model for DME Combustion in Diesel Engines

    DEFF Research Database (Denmark)

    Bek, Bjarne H.; Sorenson, Spencer C.

    1998-01-01

    A series of studies has been conducted investigating the behavior of di-methyl ether (DME) fuel jets injected into quiescent combus-tion chambers. These studies have shown that it is possible to make a good estimate of the penetration of the jet based on existing correlations for diesel fuel...

  15. A mixing based model for DME combustion in diesel engines

    DEFF Research Database (Denmark)

    Bek, Bjarne Hjort; Sorenson, Spencer C

    2001-01-01

    A series of studies has been conducted investigating the behavior of di-methyl ether (DME) fuel jets injected into quiescent combustion chambers. These studies have shown that it is possible to make a good estimate of the penetration of the jet based on existing correlations for diesel fuel...

  16. Optical Power Source Derived from Engine Combustion Chambers

    Science.gov (United States)

    Baumbick, Robert J. (Inventor)

    1999-01-01

    An optical power source is disclosed that collects the spectra of the light emissions created in a combustion chamber to provide its optical output signals that serve the needs of optical networks. The light spectra is collected by a collection ring serving as an optical waveguide.

  17. Numerical investigation of CAI Combustion in the Opposed- Piston Engine with Direct and Indirect Water Injection

    Science.gov (United States)

    Pyszczek, R.; Mazuro, P.; Teodorczyk, A.

    2016-09-01

    This paper is focused on the CAI combustion control in a turbocharged 2-stroke Opposed-Piston (OP) engine. The barrel type OP engine arrangement is of particular interest for the authors because of its robust design, high mechanical efficiency and relatively easy incorporation of a Variable Compression Ratio (VCR). The other advantage of such design is that combustion chamber is formed between two moving pistons - there is no additional cylinder head to be cooled which directly results in an increased thermal efficiency. Furthermore, engine operation in a Controlled Auto-Ignition (CAI) mode at high compression ratios (CR) raises a possibility of reaching even higher efficiencies and very low emissions. In order to control CAI combustion such measures as VCR and water injection were considered for indirect ignition timing control. Numerical simulations of the scavenging and combustion processes were performed with the 3D CFD multipurpose AVL Fire solver. Numerous cases were calculated with different engine compression ratios and different amounts of directly and indirectly injected water. The influence of the VCR and water injection on the ignition timing and engine performance was determined and their application in the real engine was discussed.

  18. Genetic Algorithm-Based Design Optimization of Electromagnetic Valve Actuators in Combustion Engines

    Directory of Open Access Journals (Sweden)

    Seung Hwan Lee

    2015-11-01

    Full Text Available In this research, the design of a new electromagnetic engine valve in the limited space of combustion engine is optimized by multidisciplinary simulation using MATLAB and Maxwell. An electromagnetic engine valve actuator using a permanent magnet is a new actuator concept for overcoming the inherent drawbacks of the conventional solenoid-driven electromagnetic engine valve actuator, such as high power consumption and so on. This study aims to maximize the vibration frequency of the armature to reduce the transition time of the engine valve. The higher performance of the new actuator is demonstrated by dynamic finite element analysis.

  19. A Study on the Combustion Performance of Diesel Engines with O2 and CO2 Suction

    Directory of Open Access Journals (Sweden)

    Qinming Tan

    2016-01-01

    Full Text Available Based on the chemical reaction mechanism of fuel combustion, NOx in the diesel emissions is mainly generated from N2 inside the burning environment of engine cylinder. Taking the gas mixture, O2 and CO2, as the intake air, nitrogen-free intake is accessible, and through simulative calculations and experiments, researchers can make a study of the ignition and combustion performances of the engines. Taking a type of “4135ACa” diesel engine as the research object, the study suggested the following: in the environment of O2 and CO2, only when the volume fraction of O2 reaches 45% can the engine be ignited and kept running; engine operation became more steady after its O2 percentage increased to 50%. There is no NOx emission of engine’s nitrogen-free combustion, despite some black particles in the exhaust gas. So, the bottleneck of “NOx-Soot” emission is successfully transformed into how to optimize the combustion performance of engines. Additionally, through simulative calculations, influences of the O2 volume fraction on the nitrogen-free combustion performance have been researched; results suggested that it can help promote the burning efficiency with the increase of O2. When it reached 60%, its heat output in the cylinder has been equal to that under the operation condition of air intake. Therefore, nitrogen-free combustion can be used in some NOx control area, especially to some power plant which worked underwater. The huge gas consumption can be recycled from exhaust gas by closed cycle.

  20. FORMALIZATION OF DIESEL ENGINE OPERATION CONSIDERING THE EVALUATION OF VELOCITY DURING THE COMBUSTION PROCESSES

    Directory of Open Access Journals (Sweden)

    V. P. Litvinenko

    2015-10-01

    Full Text Available Purpose. Under modern conditions the applying methods and design models as well as the evaluation of the operational characteristics of diesel engines do not completely take into consideration the specifics of the combustion processes. In part, such situation is characterized by the complexity of considering of varied by its nature processes that haven’t been completely investigated. In this context it is necessary to find the new methods and models which would provide relatively simple solutions through the use of integrated factors based on the analysis of parameters of diesel engines. Methodology. The proposed algorithms for the estimating of the combustion process in the form of volumetric and linear velocities is based on the well-known parameters of power and mean effective pressure and allows to compare the efficiency of their behavior in various versions of diesel engines. Findings. The author specified that the volumetric / linear velocity ratio is characterized by some strength and depends on the geometric dimensions of the cylinder-piston group. Due to the assumptions it has become possible to consider the operation of a diesel engine as a system comprising: 1 the subsystem that provides the possibility of obtaining the thermal energy; 2 the subsystem providing the thermal energy transformation; 3 the subsystem that provides the necessary diesel engine power depending on terms of combustion of air-fuel mixture. Originality. The author of the paper proposed the indices of volumetric and linear combustion velocity of air-fuel mixture in the engine cylinder, that allow to obtain the comparative value in different modifications taking into account the possible choice of optimum ratio. Practical value. The usage of indices of volumetric and linear velocities of the combustion processes in the engine cylinder combined with a mathematical model will simplify the method of diesels calculating. Parametric indices of the mentioned velocities

  1. Visualizations of Gas fuel Jet and Combustion Flame on Hydrogen Rotary Engine

    OpenAIRE

    田端, 道彦; 香川, 良二

    2011-01-01

    [Abstract] In this paper, it is a purpose to obtain basic information of a hydrogen jet and combustion flame characteristics of the hydrogen rotary engine. The jet characteristics of the hydrogen gas injector were measured by using the high-speed shadowgraph method. As the result, the jet penetration of the low density gas was weak. The mixing of the direction of the jet axis was disturbed for the low jet pressure. Next, the combustion flame propagation of the hydrogen rotary engine was visua...

  2. Lean-rich axial stage combustion in a can-annular gas turbine engine

    Energy Technology Data Exchange (ETDEWEB)

    Laster, Walter R.; Szedlacsek, Peter

    2016-06-14

    An apparatus and method for lean/rich combustion in a gas turbine engine (10), which includes a combustor (12), a transition (14) and a combustor extender (16) that is positioned between the combustor (12) and the transition (14) to connect the combustor (12) to the transition (14). Openings (18) are formed along an outer surface (20) of the combustor extender (16). The gas turbine (10) also includes a fuel manifold (28) to extend along the outer surface (20) of the combustor extender (16), with fuel nozzles (30) to align with the respective openings (18). A method (200) for axial stage combustion in the gas turbine engine (10) is also presented.

  3. Combustion, performance and emissions characteristics of a newly developed CRDI single cylinder diesel engine

    Indian Academy of Sciences (India)

    Avinash Kumar Agarwal; Paras Gupta; Atul Dhar

    2015-09-01

    For improving engine performance, combustion and controlling emissions from compression ignition (CI) engines, common rail direct injection (CRDI) technology offers limitless possibilities by controlling fuel injection parameters such as fuel injection pressure, start of injection (SOI) timing, rate of fuel injection and injection duration. CRDI systems available commercially are quite complex and use a large number of sensors, hardware and analytical circuits, which make them very expensive and unfeasible for cheaper single cylinder engines, typically used in agricultural sector and decentralized power sector. This paper covers experimental investigations of a simpler version of CRDI system developed for a constant-speed, single-cylinder engine. Modifications in the cylinder head for accommodating solenoid injector, designing injector driver circuit and development of high pressure stage controls were some of the engine modification and development tasks undertaken. SOI timing is an important parameter for improving engine's combustion characteristics. SOI timings were varied between 25° and 40° BTDC for investigating engine's performance, emissions and combustion characteristics. Advanced fuel injections showed higher heat release rate (HRR), cylinder pressure and rate of pressure rise (RoPR) because of relatively longer ignition delay experienced. Lowest brake specific fuel consumption (BSFC) was obtained for 34° CA BTDC SOI. Reduction in engine out emissions except NOx was observed for advanced fuel injection timings for this newly developed CRDI system.

  4. Investigation of diesel engine for low exhaust emissions with different combustion chambers

    Directory of Open Access Journals (Sweden)

    Ghodke Pundlik R.

    2015-01-01

    Full Text Available Upcoming stringent Euro-6 emission regulations for passenger vehicle better fuel economy, low cost are the key challenges for engine development. In this paper, 2.2L, multi cylinder diesel engine have been tested for four different piston bowls designed for compression ratio of CR 15.5 to improve in cylinder performance and reduce emissions. These combustion chambers were verified in CFD at two full load points. 14 mode points have been derived using vehicle model run in AVL CRUISE software as per NEDC cycle based on time weightage factor. Base engine with compression ratio CR16.5 for full load performance and 14-mode points on Engine test bench was taken as reference for comparison. The bowl with flat face on bottom corner has shown reduction 25% and 12 % NOx emissions at 1500 and 3750 rpm full load points at same level of Soot emissions. Three piston bowls were tested for full load performance and 14 mode points on engine test bench and combustion chamber ‘C’ has shown improvement in thermal efficiency by 0.8%. Combinations of cooled EGR and combustion chamber ‘C’ with geometrical changes in engine have reduced exhaust NOx, soot and CO emissions by 22%, 9 % and 64 % as compared to base engine at 14 mode points on engine test bench.

  5. Fuel Chemistry And Combustion Distribution Effects On Rocket Engine Combustion Stability

    Science.gov (United States)

    2015-11-19

    model, the D 2 law rate constant for ideal combustion, k0, of a droplet is dependent on the thermal properties of the fuel and oxidizer and is...remaining increase in the D 2 law regression rate constant is caused by the non- ideal conditions of the experiment. Natural convection is present, as...is the gap-averaged pressure. Considering incompressible gas flow (ρ is constant ), two governing equations can be solved for the pressure in the gap

  6. Photographic Study of Combustion in a Rocket Engine I : Variation in Combustion of Liquid Oxygen and Gasoline with Seven Methods of Propellant Injection

    Science.gov (United States)

    Bellman, Donald R; Humphrey, Jack C

    1948-01-01

    Motion pictures at camera speeds up to 3000 frames per second were taken of the combustion of liquid oxygen and gasoline in a 100-pound-thrust rocket engine. The engine consisted of thin contour and injection plates clamped between two clear plastic sheets forming a two-dimensional engine with a view of the entire combustion chamber and nozzle. A photographic investigation was made of the effect of seven methods of propellant injection on the uniformity of combustion. From the photographs, it was found that the flame front extended almost to the faces of the injectors with most of the injection methods, all the injection systems resulted in a considerable nonuniformity of combustion, and luminosity rapidly decreased in the divergent part of the nozzle. Pressure vibration records indicated combustion vibrations that approximately corresponded to the resonant frequencies of the length and the thickness of the chamber. The combustion temperature divided by the molecular weight of the combustion gases as determined from the combustion photographs was about 50 to 70 percent of the theoretical value.

  7. Development of a phenomenological cycle simulation for a natural gas-fuelled, compression-ignited, internal combustion engine

    Science.gov (United States)

    Liu, Yafeng

    Engine cycle simulations have been developed for modeling both diesel and dual fuel combustion in compression ignition engines. The primary objective of this work was to investigate the dual fuel combustion process in an engine and to better understand the processes of ignition, flame propagation, and pollutant formation in the engine. A multizone diesel combustion model was first developed to predict the diesel combustion process and emissions for diesel fueling. A phenomenological combustion model for dual fuel operation was then developed to simulate the combustion process and emissions of a micro-pilot diesel ignition natural gas fueled engine. Coupled with the chemical equilibrium reactions for emission formation (i.e., extended Zeldovich NOx mechanism, soot formation and destruction submodeling, unburned hydrocarbon emissions submodeling), models for diesel droplet evaporation, air entrainment, cylinder heat transfer, piston work, mass flow rates, flame propagation, crevice flow, and flame quenching have been combined with a thermodynamic analysis of the engine to yield instantaneous cylinder conditions, engine performance, and emissions. Parametric and comparison studies of diesel operation, dual fuel combustion, and micro-pilot combustion have been conducted. The major conclusions that can be drawn from this work include (1) diesel evaporation and air entrainment can have significant influence on the ignition and combustion processes, (2) pressure and temperature of inlet air, compression ratio, and the start of fuel injection are important engine operating and design parameters, (3) the combustion process of the mixture of natural gas and air is dominantly premixed-combustion, and (4) the processes of crevice flow and flame quenching can have a substantial impact on the dual fuel/micro-pilot combustion and emission formation processes.

  8. An internal combustion engine with interconnected multicylinder arrangement. Verbrennungsmotor mit Mehrzylinderverbund

    Energy Technology Data Exchange (ETDEWEB)

    Mosdell, R.

    1990-08-02

    The invention is dedicated to the kinematic characteristics of multicylinder/multichamber internal combustion engine crank mechanisms and intends to reduce internal energy losses due to mass inertia during combustion energy (impulse) transmission to the piston, connecting rod and crankshaft. This reduction is achieved by modifying the gas exchange control of conventional four-cycle or two-cycle diesel engines, four-cycle or two-cycle spark ignition engines or four-cycle Wankel engines. The ususal successive ignition order of individual cylinders according to the number of cylinders on the crankshaft is replaced by an arrangement of several interconnected cylinders which ignite simultaneously or time-delayed, thus increasing the combustion energy (impulse) and reducing the mass inertia of the piston, connecting rod, crankshaft, disk flywheel and drive components by division. Especially the Wankel engine is expected to profit by the invention's design because of the relatively high mass inertia of all its movable transmission elements and because of higher instantaneous combustion impulses due to doubling, which account for an unproportionately high performance increase.

  9. Combustion Dynamics and Control for Ultra Low Emissions in Aircraft Gas-Turbine Engines

    Science.gov (United States)

    DeLaat, John C.

    2011-01-01

    Future aircraft engines must provide ultra-low emissions and high efficiency at low cost while maintaining the reliability and operability of present day engines. The demands for increased performance and decreased emissions have resulted in advanced combustor designs that are critically dependent on efficient fuel/air mixing and lean operation. However, all combustors, but most notably lean-burning low-emissions combustors, are susceptible to combustion instabilities. These instabilities are typically caused by the interaction of the fluctuating heat release of the combustion process with naturally occurring acoustic resonances. These interactions can produce large pressure oscillations within the combustor and can reduce component life and potentially lead to premature mechanical failures. Active Combustion Control which consists of feedback-based control of the fuel-air mixing process can provide an approach to achieving acceptable combustor dynamic behavior while minimizing emissions, and thus can provide flexibility during the combustor design process. The NASA Glenn Active Combustion Control Technology activity aims to demonstrate active control in a realistic environment relevant to aircraft engines by providing experiments tied to aircraft gas turbine combustors. The intent is to allow the technology maturity of active combustion control to advance to eventual demonstration in an engine environment. Work at NASA Glenn has shown that active combustion control, utilizing advanced algorithms working through high frequency fuel actuation, can effectively suppress instabilities in a combustor which emulates the instabilities found in an aircraft gas turbine engine. Current efforts are aimed at extending these active control technologies to advanced ultra-low-emissions combustors such as those employing multi-point lean direct injection.

  10. Research Needs and Impacts in Predictive Simulation for Internal Combustion Engines (PreSICE)

    Energy Technology Data Exchange (ETDEWEB)

    Eckerle, Wayne [Cummins, Inc., Columbus, IN (United States); Rutland, Chris [Univ. of Wisconsin, Madison, WI (United States); Rohlfing, Eric [Dept. of Energy (DOE), Washington DC (United States). Office of Science; Singh, Gurpreet [Dept. of Energy (DOE), Washington DC (United States). Office of Energy Efficiency and Renewable Energy; McIlroy, Andrew [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2011-03-03

    This report is based on a SC/EERE Workshop to Identify Research Needs and Impacts in Predictive Simulation for Internal Combustion Engines (PreSICE), held March 3, 2011, to determine strategic focus areas that will accelerate innovation in engine design to meet national goals in transportation efficiency. The U.S. has reached a pivotal moment when pressures of energy security, climate change, and economic competitiveness converge. Oil prices remain volatile and have exceeded $100 per barrel twice in five years. At these prices, the U.S. spends $1 billion per day on imported oil to meet our energy demands. Because the transportation sector accounts for two-thirds of our petroleum use, energy security is deeply entangled with our transportation needs. At the same time, transportation produces one-quarter of the nation’s carbon dioxide output. Increasing the efficiency of internal combustion engines is a technologically proven and cost-effective approach to dramatically improving the fuel economy of the nation’s fleet of vehicles in the near- to mid-term, with the corresponding benefits of reducing our dependence on foreign oil and reducing carbon emissions. Because of their relatively low cost, high performance, and ability to utilize renewable fuels, internal combustion engines—including those in hybrid vehicles—will continue to be critical to our transportation infrastructure for decades. Achievable advances in engine technology can improve the fuel economy of automobiles by over 50% and trucks by over 30%. Achieving these goals will require the transportation sector to compress its product development cycle for cleaner, more efficient engine technologies by 50% while simultaneously exploring innovative design space. Concurrently, fuels will also be evolving, adding another layer of complexity and further highlighting the need for efficient product development cycles. Current design processes, using “build and test” prototype engineering, will not

  11. Research Needs and Impacts in Predictive Simulation for Internal Combustion Engines (PreSICE)

    Energy Technology Data Exchange (ETDEWEB)

    Eckerle, Wayne [Cummins, Inc., Columbus, IN (United States); Rutland, Chris [Univ. of Wisconsin, Madison, WI (United States); Rohlfing, Eric [Dept. of Energy (DOE), Washington DC (United States). Office of Science; Singh, Gurpreet [Dept. of Energy (DOE), Washington DC (United States). Office of Energy Efficiency and Renewable Energy; McIlroy, Andrew [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2011-03-03

    This report is based on a SC/EERE Workshop to Identify Research Needs and Impacts in Predictive Simulation for Internal Combustion Engines (PreSICE), held March 3, 2011, to determine strategic focus areas that will accelerate innovation in engine design to meet national goals in transportation efficiency. The U.S. has reached a pivotal moment when pressures of energy security, climate change, and economic competitiveness converge. Oil prices remain volatile and have exceeded $100 per barrel twice in five years. At these prices, the U.S. spends $1 billion per day on imported oil to meet our energy demands. Because the transportation sector accounts for two-thirds of our petroleum use, energy security is deeply entangled with our transportation needs. At the same time, transportation produces one-quarter of the nation’s carbon dioxide output. Increasing the efficiency of internal combustion engines is a technologically proven and cost-effective approach to dramatically improving the fuel economy of the nation’s fleet of vehicles in the near- to mid-term, with the corresponding benefits of reducing our dependence on foreign oil and reducing carbon emissions. Because of their relatively low cost, high performance, and ability to utilize renewable fuels, internal combustion engines—including those in hybrid vehicles—will continue to be critical to our transportation infrastructure for decades. Achievable advances in engine technology can improve the fuel economy of automobiles by over 50% and trucks by over 30%. Achieving these goals will require the transportation sector to compress its product development cycle for cleaner, more efficient engine technologies by 50% while simultaneously exploring innovative design space. Concurrently, fuels will also be evolving, adding another layer of complexity and further highlighting the need for efficient product development cycles. Current design processes, using “build and test” prototype engineering, will not

  12. Effects of ethanol on combustion and emissions of a gasoline engine operating with different combustion modes

    OpenAIRE

    Ojapah, MM; Zhao, H.; Zhang, Y.

    2016-01-01

    The introduction of fuel economy and CO2 emission legislations for passenger cars in many countries and regions has spurred the research and development of more efficient gasoline engines. The pumping loss at part-load operations is a major factor for the higher fuel consumption of spark ignition (SI) gasoline engines than the diesel engines. Various approaches have been identified to reduce the pumping loss at part-load operations, leading to improved fuel economy, including Early Intake Val...

  13. A statistical model for combustion resonance from a DI diesel engine with applications

    Science.gov (United States)

    Bodisco, Timothy; Low Choy, Samantha; Masri, Assaad; Brown, Richard J.

    2015-08-01

    Introduced in this paper is a Bayesian model for isolating the resonant frequency from combustion chamber resonance. The model shown in this paper focused on characterising the initial rise in the resonant frequency to investigate the rise of in-cylinder bulk temperature associated with combustion. By resolving the model parameters, it is possible to determine: the start of pre-mixed combustion, the start of diffusion combustion, the initial resonant frequency, the resonant frequency as a function of crank angle, the in-cylinder bulk temperature as a function of crank angle and the trapped mass as a function of crank angle. The Bayesian method allows for individual cycles to be examined without cycle-averaging-allowing inter-cycle variability studies. Results are shown for a turbo-charged, common-rail compression ignition engine run at 2000 rpm and full load.

  14. The railplug: Development of a new ignitor for internal combustion engines. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, R.D.; Nichols, S.P.; Weldon, W.F.

    1994-11-29

    A three year investigation of a new type of ignitor for internal combustion engines has been performed using funds from the Advanced Energy Projects Program of The Basic Energy Sciences Division of the U.S. Department of Energy and with matching funding from Research Applications, Inc. This project was a spin-off of {open_quotes}Star Wars{close_quotes} defense technology, specifically the railgun. The {open_quotes}railplug{close_quotes} is a miniaturized railgun which produces a high velocity plume of plasma that is injected into the combustion chamber of an engine. Unlike other types of alternative ignitors, such as plasma jet ignitors, electromagnetic forces enhance the acceleration of the plasma generated by a railplug. Thus, for a railplug, the combined effects of electromagnetic and thermodynamic forces drive the plasma into the combustion chamber. Several engine operating conditions or configurations can be identified that traditionally present ignition problems, and might benefit from enhanced ignition systems. One of these is ultra-lean combustion in spark ignition (SI) engines. This concept has the potential for lowering emissions of NOx while simultaneously improving thermal efficiency. Unfortunately, current lean burn engines cannot be operated sufficiently lean before ignition related problems are encountered to offer any benefits. High EGR engines have similar potential for emissions improvement, but also experience similar ignition problems, particularly at idle. Other potential applications include diesel cold start, alcohol and dual fuel engines, and high altitude relight of gas turbines. The railplug may find application for any of the above. This project focused on three of these potential applications: lean burn SI engines, high EGR SI engines, and diesel cold start.

  15. The railplug: Development of a new ignitor for internal combustion engines

    Science.gov (United States)

    Matthews, R. D.; Nichols, S. P.; Weldon, W. F.

    1994-11-01

    A three year investigation of a new type of ignitor for internal combustion engines has been performed using funds from the Advanced Energy Projects Program of The Basic Energy Sciences Division of the U.S. Department of Energy and with matching funding from Research Applications, Inc. This project was a spin-off of 'Star Wars' defense technology, specifically the railgun. The 'railplug' is a miniaturized railgun which produces a high velocity plume of plasma that is injected into the combustion chamber of an engine. Unlike other types of alternative ignitors, such as plasma jet ignitors, electromagnetic forces enhance the acceleration of the plasma generated by a railplug. Thus, for a railplug, the combined effects of electromagnetic and thermodynamic forces drive the plasma into the combustion chamber. Several engine operating conditions or configurations can be identified that traditionally present ignition problems, and might benefit from enhanced ignition systems. One of these is ultra-lean combustion in spark ignition (SI) engines. This concept has the potential for lowering emissions of NO(x) while simultaneously improving thermal efficiency. Unfortunately, current lean burn engines cannot be operated sufficiently lean before ignition related problems are encountered to offer any benefits. High EGR engines have similar potential for emissions improvement, but also experience similar ignition problems, particularly at idle. Other potential applications include diesel cold start, alcohol and dual fuel engines, and high altitude relight of gas turbines. The railplug may find application for any of the above. This project focused on three of these potential applications: lean burn SI engines, high EGR SI engines, and diesel cold start.

  16. Effect of Various Ignition Timings on Combustion Process and Performance of Gasoline Engine

    Directory of Open Access Journals (Sweden)

    Lukáš Tunka

    2017-01-01

    Full Text Available This article deals with the effect of the ignition timing on the output parameters of a spark-ignition engine. The main assessed parameters include the output parameters of the engine (engine power and torque, cylinder pressure variation, heat generation and burn rate. However, the article also discusses the effect of the ignition timing on the temperature of exhaust gases, the indicated mean effective pressure, the combustion duration, combustion stability, etc. All measurements were performed in an engine test room in the Department of Technology and Automobile Transport at Mendel University in Brno, on a four-cylinder AUDI engine with a maximum power of 110 kW, as indicated by the manufacturer. To control and change the ignition timing of the engine, a fully programmable Magneti Marelli control unit was used. The experimental measurements were performed on 8 different ignition timings, from 18 °CA to 32 °CA BTDC at wide throttle open and a constant engine speed (2500 rpm, with a stoichiometric mixture fraction. The measurement results showed that as the ignition timing increases, the engine power and torque also increase. The increase in these parameters is a reflection of higher pressure in the cylinder, the maximum value of which is achieved at a higher ignition timing near top dead centre in thepower stroke. In these conditions we can expect higher engine efficiency. It was also found that the combustion is more stable with a higher value of ignition timing. No significant difference was found in the combustion duration.

  17. Fundamental Phenomena on Fuel Decomposition and Boundary-Layer Combustion Precesses with Applications to Hybrid Rocket Motors. Part 1; Experimental Investigation

    Science.gov (United States)

    Kuo, Kenneth K.; Lu, Yeu-Cherng; Chiaverini, Martin J.; Johnson, David K.; Serin, Nadir; Risha, Grant A.; Merkle, Charles L.; Venkateswaran, Sankaran

    1996-01-01

    This final report summarizes the major findings on the subject of 'Fundamental Phenomena on Fuel Decomposition and Boundary-Layer Combustion Processes with Applications to Hybrid Rocket Motors', performed from 1 April 1994 to 30 June 1996. Both experimental results from Task 1 and theoretical/numerical results from Task 2 are reported here in two parts. Part 1 covers the experimental work performed and describes the test facility setup, data reduction techniques employed, and results of the test firings, including effects of operating conditions and fuel additives on solid fuel regression rate and thermal profiles of the condensed phase. Part 2 concerns the theoretical/numerical work. It covers physical modeling of the combustion processes including gas/surface coupling, and radiation effect on regression rate. The numerical solution of the flowfield structure and condensed phase regression behavior are presented. Experimental data from the test firings were used for numerical model validation.

  18. Spark Ignition Engine Combustion, Performance and Emission Products from Hydrous Ethanol and Its Blends with Gasoline

    Directory of Open Access Journals (Sweden)

    Musaab O. El-Faroug

    2016-11-01

    Full Text Available This paper reviews the serviceability of hydrous ethanol as a clean, cheap and green renewable substitute fuel for spark ignition engines and discusses the comparative chemical and physical properties of hydrous ethanol and gasoline fuels. The significant differences in the properties of hydrous ethanol and gasoline fuels are sufficient to create a significant change during the combustion phase of engine operation and consequently affect the performance of spark-ignition (SI engines. The stability of ethanol-gasoline-water blends is also discussed. Furthermore, the effects of hydrous ethanol, and its blends with gasoline fuel on SI engine combustion characteristics, cycle-to-cycle variations, engine performance parameters, and emission characteristics have been highlighted. Higher water solubility in ethanol‑gasoline blends may be obviously useful and suitable; nevertheless, the continuous ability of water to remain soluble in the blend is significantly affected by temperature. Nearly all published engine experimental results showed a significant improvement in combustion characteristics and enhanced engine performance for the use of hydrous ethanol as fuel. Moreover, carbon monoxide and oxides of nitrogen emissions were also significantly decreased. It is also worth pointing out that unburned hydrocarbon and carbon dioxide emissions were also reduced for the use of hydrous ethanol. However, unregulated emissions such as acetaldehyde and formaldehyde were significantly increased.

  19. Thermal Loss Determination for a Small Internal Combustion Engine

    Science.gov (United States)

    2014-03-27

    not dependent on drivetrain components connected to the engine, so compensation for additional frictional loading is not necessary when recording...provided by means of a blower (shown on the left). The engine crankshaft was coupled to the drivetrain (located on the right). Intake air was routed...stainless steel tube and Honeywell TJE pressure transducer. The engine drivetrain was set up as shown in Figure 3.3. Ruland bellows shaft couplers were

  20. Modeling of scalar dissipation rates in flamelet models for low temperature combustion engine simulations

    CERN Document Server

    Gupta, Saurabh; Pal, Pinaki; Im, Hong G

    2014-01-01

    The flamelet approach offers a viable framework for combustion modeling of homogeneous charge compression ignition (HCCI) engines under stratified mixture conditions. Scalar dissipation rate acts as a key parameter in flamelet-based combustion models which connects the physical mixing space to the reactive space. The aim of this paper is to gain fundamental insights into turbulent mixing in low temperature combustion (LTC) engines and investigate the modeling of scalar dissipation rate. Three direct numerical simulation (DNS) test cases of two-dimensional turbulent auto-ignition of a hydrogen-air mixture with different correlations of temperature and mixture fraction are considered, which are representative of different ignition regimes. The existing models of mean and conditional scalar dissipation rates, and probability density functions (PDFs) of mixture fraction and total enthalpy are a priori validated against the DNS data.

  1. Combustion and emissions of the diesel engine using bio-diesel fuel

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The combustion and heat release of engines using diesel fuel and bio-diesel fuel have been investigated.The results illustrate that the combustion happens in advance and the ignition delay period is shortened.The initial heat release peak declines a little,the corresponding crankshaft angle changes in advance,and the combustion duration is prolonged.The economic performance and emission features of diesel engines using diesel fuel and bio-diesel fuel are compared.The results also show that the specific fuel consumption of bio-diesel increases by about 12% .The emissions,such as CO,HC,and particulate matter decrease remarkably whereas NOx increases a little.

  2. Effect of hydrogen-diesel combustion on the performance and combustion parameters of a dual fuelled diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Bose, P.K.; Banerjee, Rahul; Deb, Madhujit [Mechanical Engineering Department, National Institute of Technology, Agartala, Tripura-799055 (India)

    2013-07-01

    Petroleum crude is expected to remain main source of transport fuels at least for the next 20 to 30 years. The petroleum crude reserves however, are declining and consumption of transport fuels particularly in the developing countries is increasing at high rates. Severe shortage of liquid fuels derived from petroleum may be faced in the second half of this century. In this paper, experiments are performed in a fur stroke, single cylinder, compression ignition diesel engine with dual fuel mode. Diesel and hydrogen are used as pilot liquid and primary gaseous fuel, respectively. The objective of this study is to find out the effects on combustion and performance parameters observed at diesel hydrogen fuel mixture for all the different loadings (2kg,4kg,6kg,8kg,10kg and 12kg) in the engine.

  3. Efficiency of a new internal combustion engine concept with variable piston motion

    Directory of Open Access Journals (Sweden)

    Dorić Jovan Ž.

    2014-01-01

    Full Text Available This paper presents simulation of working process in a new IC engine concept. The main feature of this new IC engine concept is the realization of variable movement of the piston. With this unconventional piston movement it is easy to provide variable compression ratio, variable displacement and combustion during constant volume. These advantages over standard piston mechanism are achieved through synthesis of the two pairs of non-circular gears. Presented mechanism is designed to obtain a specific motion law which provides better fuel consumption of IC engines. For this paper Ricardo/WAVE software was used, which provides a fully integrated treatment of time-dependent fluid dynamics and thermodynamics by means of onedimensional formulation. The results obtained herein include the efficiency characteristic of this new heat engine concept. The results show that combustion during constant volume, variable compression ratio and variable displacement have significant impact on improvement of fuel consumption.

  4. Effect of Fuel Types on Combustion Characteristics and Performance of a Four Stroke IC Engine

    Directory of Open Access Journals (Sweden)

    Mrs. Rana Ali Hussein,

    2014-04-01

    Full Text Available In this study, the effect of Gasoline, Ethanol, Gasohol E10, and Kerosene on the performance and combustion characteristics of a spark ignition (SI engine were investigated. In the experiment, the internal combustion (IC engine includes one cylinder, two valves, and four stroke spark ignition. Performance tests were carried out for specific fuel consumption, brake specific fuel consumption, power developed, corrosion rate, and carbon dioxide (CO2 and carbon monoxide (CO emissions. The measurements were conducted under various engine speeds ranging from 1500 to 4500 rpm. The experimental results showed that the performance of engine was improved with the use of gasoline and gasohol E10 in comparison with the Ethanol and Kerosene. The concentrations of CO2 and CO were presented and compared for all type of fuel examined.

  5. Experimental study of hydrogen as a fuel additive in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Saanum, Inge

    2008-07-01

    Combustion of hydrocarbons in internal combustion engines results in emissions that can be harmful both to human health and to the environment. Although the engine technology is improving, the emissions of NO{sub x}, PM and UHC are still challenging. Besides, the overall consumption of fossil fuel and hence the emissions of CO{sub 2} are increasing because of the increasing number of vehicles. This has lead to a focus on finding alternative fuels and alternative technologies that may result in lower emissions of harmful gases and lower CO{sub 2} emissions. This thesis treats various topics that are relevant when using blends of fuels in different internal combustion engine technologies, with a particular focus on using hydrogen as a fuel additive. The topics addressed are especially the ones that impact the environment, such as emissions of harmful gases and thermal efficiency (fuel consumption). The thesis is based on experimental work performed at four different test rigs: 1. A dynamic combustion rig with optical access to the combustion chamber where spark ignited premixed combustion could be studied by means of a Schlieren optical setup and a high speed video camera. 2. A spark ignition natural gas engine rig with an optional exhaust gas recycling system. 3. A 1-cylinder diesel engine prepared for homogeneous charge compression ignition combustion. 4. A 6-cylinder standard diesel engine The engine rigs were equipped with cylinder pressure sensors, engine dynamometers, exhaust gas analyzers etc. to enable analyses of the effects of different fuels. The effect of hydrogen blended with methane and natural gas in spark ignited premixed combustion was investigated in the dynamic combustion rig and in a natural gas engine. In the dynamic combustion rig, the effect of hydrogen added to methane on the flame speed and the flame structure was investigated at elevated pressure and temperature. A considerable increase in the flame speed was observed when adding 30 vol

  6. Experimental study of hydrogen as a fuel additive in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Saanum, Inge

    2008-07-01

    Combustion of hydrocarbons in internal combustion engines results in emissions that can be harmful both to human health and to the environment. Although the engine technology is improving, the emissions of NO{sub x}, PM and UHC are still challenging. Besides, the overall consumption of fossil fuel and hence the emissions of CO{sub 2} are increasing because of the increasing number of vehicles. This has lead to a focus on finding alternative fuels and alternative technologies that may result in lower emissions of harmful gases and lower CO{sub 2} emissions. This thesis treats various topics that are relevant when using blends of fuels in different internal combustion engine technologies, with a particular focus on using hydrogen as a fuel additive. The topics addressed are especially the ones that impact the environment, such as emissions of harmful gases and thermal efficiency (fuel consumption). The thesis is based on experimental work performed at four different test rigs: 1. A dynamic combustion rig with optical access to the combustion chamber where spark ignited premixed combustion could be studied by means of a Schlieren optical setup and a high speed video camera. 2. A spark ignition natural gas engine rig with an optional exhaust gas recycling system. 3. A 1-cylinder diesel engine prepared for homogeneous charge compression ignition combustion. 4. A 6-cylinder standard diesel engine The engine rigs were equipped with cylinder pressure sensors, engine dynamometers, exhaust gas analyzers etc. to enable analyses of the effects of different fuels. The effect of hydrogen blended with methane and natural gas in spark ignited premixed combustion was investigated in the dynamic combustion rig and in a natural gas engine. In the dynamic combustion rig, the effect of hydrogen added to methane on the flame speed and the flame structure was investigated at elevated pressure and temperature. A considerable increase in the flame speed was observed when adding 30 vol

  7. The laboratory test rig with miniature jet engine to research aviation fuels combustion process

    OpenAIRE

    Gawron Bartosz; Białecki Tomasz

    2015-01-01

    This article presents laboratory test rig with a miniature turbojet engine (MiniJETRig – Miniature Jet Engine Test Rig), that was built in the Air Force Institute of Technology. The test rig has been developed for research and development works aimed at modelling and investigating processes and phenomena occurring in full scale jet engines. In the article construction of a test rig is described, with a brief discussion on the functionality of each of its main components. Additionally examples...

  8. Acceleration of the chemistry solver for modeling DI engine combustion using dynamic adaptive chemistry (DAC) schemes

    Science.gov (United States)

    Shi, Yu; Liang, Long; Ge, Hai-Wen; Reitz, Rolf D.

    2010-03-01

    Acceleration of the chemistry solver for engine combustion is of much interest due to the fact that in practical engine simulations extensive computational time is spent solving the fuel oxidation and emission formation chemistry. A dynamic adaptive chemistry (DAC) scheme based on a directed relation graph error propagation (DRGEP) method has been applied to study homogeneous charge compression ignition (HCCI) engine combustion with detailed chemistry (over 500 species) previously using an R-value-based breadth-first search (RBFS) algorithm, which significantly reduced computational times (by as much as 30-fold). The present paper extends the use of this on-the-fly kinetic mechanism reduction scheme to model combustion in direct-injection (DI) engines. It was found that the DAC scheme becomes less efficient when applied to DI engine simulations using a kinetic mechanism of relatively small size and the accuracy of the original DAC scheme decreases for conventional non-premixed combustion engine. The present study also focuses on determination of search-initiating species, involvement of the NOx chemistry, selection of a proper error tolerance, as well as treatment of the interaction of chemical heat release and the fuel spray. Both the DAC schemes were integrated into the ERC KIVA-3v2 code, and simulations were conducted to compare the two schemes. In general, the present DAC scheme has better efficiency and similar accuracy compared to the previous DAC scheme. The efficiency depends on the size of the chemical kinetics mechanism used and the engine operating conditions. For cases using a small n-heptane kinetic mechanism of 34 species, 30% of the computational time is saved, and 50% for a larger n-heptane kinetic mechanism of 61 species. The paper also demonstrates that by combining the present DAC scheme with an adaptive multi-grid chemistry (AMC) solver, it is feasible to simulate a direct-injection engine using a detailed n-heptane mechanism with 543 species

  9. Performance and analysis of a 4-stroke multi-cylinder gasoline engine with CAI combustion

    OpenAIRE

    Zhao, H.; Li, J; Ma, T.; Ladommatos, N

    2002-01-01

    Copyright © 2002 SAE International. This paper is posted on this site with permission from SAE International. Further use of this paper is not permitted without permission from SAE Controlled Auto-Ignition (CAI) combustion was realised in a production type 4-stroke 4-cylinder gasoline engine without intake charge heating or increasing compression ratio. The CAI engine operation was achieved using substantially standard components modified only in camshafts to restrict the gas exchange proc...

  10. Conflict between internal combustion engine and thermoelectric generator during waste heat recovery in cars

    Science.gov (United States)

    Korzhuev, M. A.

    2011-02-01

    It is shown that an internal combustion engine and a thermoelectric generator (TEG) arranged on the exhaust pipe of this engine come into the conflict of thermal machines that is related to using the same energy resource. The conflict grows with increasing useful electric power W e of the TEG, which leads to the limitation of both the maximum TEG output power ( W {e/max}) and the possibility of waste heat recovery in cars.

  11. Experimental validation of extended NO and soot model for advanced HD diesel engine combustion

    NARCIS (Netherlands)

    Seykens, X.L.J.; Baert, R.S.G.; Somers, L.M.T.; Willems, F.P.T.

    2009-01-01

    A computationally efficient engine model is developed based on an extended NO emission model and state-of-the-art soot model. The model predicts exhaust NO and soot emission for both conventional and advanced, high-EGR (up to 50%), heavy-duty DI diesel combustion. Modeling activities have aimed at l

  12. Knock prediction for dual fuel engines by using a simplified combustion model

    Institute of Scientific and Technical Information of China (English)

    费少梅; 刘震涛; 严兆大

    2003-01-01

    The present work used a methane-air mixture chemical kinetics scheme consisting of 119 elementary reaction steps and 41 chemical species to develop a simplified combustion model for prediction of the knock in dual fuel engines. Calculated values by the model for natural gas operation showed good agreement with corresponding experimental values over a broad range of operating conditions.

  13. Combustion Chamber Deposits and PAH Formation in SI Engines Fueled by Producer Gas from Biomass Gasification

    DEFF Research Database (Denmark)

    Ahrenfeldt, Jesper; Henriksen, Ulrik Birk; Schramm, Jesper

    2003-01-01

    Investigations were made concerning the formation of combustion chamber deposits (CCD) in SI gas engines fueled by producer gas. The main objective was to determine and characterise CCD and PAH formation caused by the presence of the light tar compounds phenol and guaiacol in producer gas from an...

  14. Auto-Ignition and Heat Release Correlations for Controlled Auto-Ignition Combustion in Gasoline Engines

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Auto-ignition and heat release correlations for controlled auto-ignition (CAI) combustion were derived from extensive in-cylinder pressure data of a four-stroke gasoline engine operating in CAI combustion mode. Abundant experiments were carried out under a wide range of air/fuel ratio,speed and residual gas fraction to ensure that the combustion correlations can be used in the entire CAI engine operation range. Furthermore, a more accurate method to compute the residual gas fraction was proposed by calculating the working fluid temperature at the exhaust valve close timing in the experiments. The heat release correlation was described in two parts, one is for the first slower heat release process at low temperature, and the other is for the second faster heat release process at high temperature. Finally the heat release correlation was evaluated on the single cylinder gasoline engine running with CAI combustion by comparing the experimental data with the 1-D engine simulation results obtained with the aid of the GT-Power simulation program. The results show that the predicted loads and ignition timings match closely with the measurements.

  15. Piston ring lubrication and hydrocarbon emissions from internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Froelund, K.

    1997-11-01

    Is it the intention with this project to improve the existing hydrocarbon emission model at the Institute by combining it with a model for predicting the piston ring lubrication. The piston ring lubrication model should be experimentally verified to ensure the validity of the model. The following items were the objectives of the current study: Develop a piston ring lubrication model. This implies the development of a ring-pack gas flow model; Examine the response of the piston ring lubrication model to changing engineer conditions. Especially, it would be interesting to look at the engine warm-up phase since this is the phase where the engine-out emissions are highest and where the commonly used three way catalyst is not capable of converting the engine-out emissions, thereby leading the engine-out emissions directly out in to the environment with the exhaust gases; In order to verify the piston ring lubrication model the lubricant distribution on the cylinder liner should be investigated experimentally. Here again it would be of great interesting to look at the engine warm-up phase; The piston ring lubrication model should be adjusted for application together with the new hydrocarbon emission model for SI-engines at the Institute in order to increase the accuracy of the latter; The piston ring lubrication model could be used for describing the transport of PAH`s in diesel engines. (EG)

  16. Evaluation of the Migrating Combustion Chamber (MCC) Engine

    Science.gov (United States)

    1993-01-01

    REPORT DOCUMENTATION PAGE OHINo. 0704-018 Pubk repatng burden bv hs cBig da inimmaion is wabdd lo aage 1 hour p. e .r wkdud toor Isen kN imo.ng ismucm...2. REPORT DATE 3. REPORT TYPE AND DATES COVERED I January 1993 Final 4. TITLE AND SUBTITLE 5. FUNDING NUMBERS Evaluation of the Migrating Combustion...Data Energy Balance Data Point Date Torque Speed Power Air Flow T1 T2 Delta T(*K) Number (oz-in) (rpm) (hp) (CFM) (IF) (OF) 23-Aug 1 3470 0.004 165 82

  17. Internal combustion engines for alcohol motor fuels: a compilation of background technical information

    Energy Technology Data Exchange (ETDEWEB)

    Blaser, Richard

    1980-11-01

    This compilation, a draft training manual containing technical background information on internal combustion engines and alcohol motor fuel technologies, is presented in 3 parts. The first is a compilation of facts from the state of the art on internal combustion engine fuels and their characteristics and requisites and provides an overview of fuel sources, fuels technology and future projections for availability and alternatives. Part two compiles facts about alcohol chemistry, alcohol identification, production, and use, examines ethanol as spirit and as fuel, and provides an overview of modern evaluation of alcohols as motor fuels and of the characteristics of alcohol fuels. The final section compiles cross references on the handling and combustion of fuels for I.C. engines, presents basic evaluations of events leading to the use of alcohols as motor fuels, reviews current applications of alcohols as motor fuels, describes the formulation of alcohol fuels for engines and engine and fuel handling hardware modifications for using alcohol fuels, and introduces the multifuel engines concept. (LCL)

  18. The realization and analysis of a new thermodynamic cycle for internal combustion engine

    Directory of Open Access Journals (Sweden)

    Dorić Jovan Ž.

    2011-01-01

    Full Text Available This paper presents description and thermodynamic analysis of a new thermodynamic cycle. Realization of this new cycle is possible to achieve with valveless internal combustion engine with more complete expansion. The main purpose of this new IC engine is to increase engines’ thermal efficiency. The engine was designed so that the thermodynamic changes of the working fluid are different than in conventional engines. Specific differences are reflected in a more complete expansion of the working fluid (the expansion stroke is larger than compression stroke, valveless gas flowing and complete discharge of residual combustion products from the combustion chamber. In this concept, the movement of the piston is different than in conventional piston mechanisms. The results obtained herein include the efficiency characteristics of irreversible reciprocating new engine cycle which is very similar to Miller cycle. The results show that with this thermodynamic cycle engine has higher efficiency than with the standard Otto cycle. In this article, the patent application material under number 2008/607 at the Intellectual Property Office of the Republic of Serbia was used.

  19. Control Scheme Formulation for the Production of Hydrogen on Demand to Feed an Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Jarniel García Morales

    2016-12-01

    Full Text Available In this work, a control strategy is presented to produce hydrogen on demand to feed an internal combustion (IC engine. For this purpose, the modeling of the IC engine fueled by gasoline blended with 10 % v/v of anhydrous ethanol (E10 and hydrogen as an additive is developed. It is considered that the hydrogen gas is produced according to the IC engine demand, and that the hydrogen gas is obtained by an alkaline electrolyzer. The gasoline–ethanol blend added into the combustion chamber is determined according to the stoichiometric ratio and the production of hydrogen gas is regulated by a proportional and integral controller (P.I.. The controller reference is varying according to the mass flow air induced into the cylinder, in order to ensure an adequate production of hydrogen gas for any operating condition of the IC engine. The main contribution of this work is the control scheme developed, through simulation, in order to produce hydrogen on demand for any operating point of an internal combustion engine fueled by an E10 blend. The simulation results showed that the use of hydrogen gas as an additive in an E10 blend decreases the E10 fuel consumption 23 % on average, and the thermal efficiency is increased approximately 2.13 % , without brake power loss in the IC engine.

  20. A University Consortium on Low Temperature Combustion for High Efficiency, Ultra-Low Emission Engines

    Energy Technology Data Exchange (ETDEWEB)

    Assanis, Dennis N. [Univ. of Michigan, Ann Arbor, MI (United States); Atreya, Arvind [Univ. of Michigan, Ann Arbor, MI (United States); Chen, Jyh-Yuan [Univ. of California, Berkeley, CA (United States); Cheng, Wai K. [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States); Dibble, Robert W. [Univ. of California, Berkeley, CA (United States); Edwards, Chris [Stanford Univ., CA (United States); Filipi, Zoran S. [Univ. of Michigan, Ann Arbor, MI (United States); Gerdes, Christian [Stanford Univ., CA (United States); Im, Hong [Univ. of Michigan, Ann Arbor, MI (United States); Lavoie, George A. [Univ. of Michigan, Ann Arbor, MI (United States); Wooldridge, Margaret S. [Univ. of Michigan, Ann Arbor, MI (United States)

    2009-12-31

    The objective of the University consortium was to investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines and develop methods to extend those boundaries to improve the fuel economy of these engines, while operating with ultra low emissions. This work involved studies of thermal effects, thermal transients and engine management, internal mixing and stratification, and direct injection strategies for affecting combustion stability. This work also examined spark-assisted Homogenous Charge Compression Ignition (HCCI) and exhaust after-treatment so as to extend the range and maximize the benefit of Homogenous Charge Compression Ignition (HCCI)/ Partially Premixed Compression Ignition (PPCI) operation. In summary the overall goals were; Investigate the fundamental processes that determine the practical boundaries of Low Temperature Combustion (LTC) engines; Develop methods to extend LTC boundaries to improve the fuel economy of HCCI engines fueled on gasoline and alternative blends, while operating with ultra low emissions; and Investigate alternate fuels, ignition and after-treatment for LTC and Partially Premixed compression Ignition (PPCI) engines.

  1. System and method for conditioning intake air to an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Sellnau, Mark C.

    2015-08-04

    A system for conditioning the intake air to an internal combustion engine includes a means to boost the pressure of the intake air to the engine and a liquid cooled charge air cooler disposed between the output of the boost means and the charge air intake of the engine. Valves in the coolant system can be actuated so as to define a first configuration in which engine cooling is performed by coolant circulating in a first coolant loop at one temperature, and charge air cooling is performed by coolant flowing in a second coolant loop at a lower temperature. The valves can be actuated so as to define a second configuration in which coolant that has flowed through the engine can be routed through the charge air cooler. The temperature of intake air to the engine can be controlled over a wide range of engine operation.

  2. Thermal radiation of heterogeneous combustion products in the model rocket engine plume

    Science.gov (United States)

    Kuzmin, V. A.; Maratkanova, E. I.; Zagray, I. A.; Rukavishnikova, R. V.

    2015-05-01

    The work presents a method of complex investigation of thermal radiation emitted by heterogeneous combustion products in the model rocket engine plume. Realization of the method has allowed us to obtain full information on the results in all stages of calculations. Dependence of the optical properties (complex refractive index), the radiation characteristics (coefficients and cross sections) and emission characteristics (flux densities, emissivity factors) of the main determining factors and parameters was analyzed. It was found by the method of computational experiment that the presence of the gaseous phase in the combustion products causes a strongly marked selectivity of emission, due to which the use of gray approximation in the calculation of thermal radiation is unnecessary. The influence of the optical properties, mass fraction, the function of particle size distribution, and the temperature of combustion products on thermal radiation in the model rocket engine plume was investigated. The role of "spotlight" effect-increasing the amount of energy of emission exhaust combustion products due to scattering by condensate particles radiation from the combustion chamber-was established quantitatively.

  3. Experimental Investigation on Space-dispersed Double-wall Jet Combustion System for DI Diesel Engine

    Institute of Scientific and Technical Information of China (English)

    郭鹏江; 高希彦

    2012-01-01

    A space-dispersed double-wall jet combustion system was developed by adopting the wall-guiding spray method and the stratification theory.The experimental test was carried out to optimize the structural parameters of the diesel-engine combustion system,including chamber structure,swirl ratio of cylinder head,included angle of jet orifice,number and diameter of jet orifice,fuel injection pressure and timing.The effect of double-wall jet combustion system on combustion and engine performance was tested to obtain the best performance indexes,and the double-wall jet combustion system was compared to the prototype.The results show that NOx is reduced from 712 PPm to 487 PPm at 2 100 r/min,and from 593 PPm to 369 PPm at 3 000 r/min,which are reduced by 31.6% and 37.7%,respectively.The smoke intensity was reduced form 3.67 BSU to 2.1 BSU,and the oil consumption was reduced from 240.5 g/(kW·h) to 225.4 g/(kW·h),which was decreased by 6.3% at low speed.The pressure in the cylinder was obviously reduced from 115 bar to 108 bar,which was reduced by 6%.

  4. Effects of ambient oxygen concentration on biodiesel and diesel spray combustion under simulated engine conditions

    KAUST Repository

    Zhang, Ji

    2013-08-01

    This study investigates the effect of ambient oxygen concentration on biodiesel and diesel spray combustion under simulated compression-ignition engine conditions in a constant-volume chamber. The apparent heat release rate (AHRR) is calculated based on the measured pressure. High-speed imaging of OH* chemiluminescence and natural luminosity (NL) is employed to visualize the combustion process. Temporally and spatially resolved NL and OH* contour plots are obtained. The result indicates that AHRR depends monotonically on the ambient oxygen concentration for both fuels. A lower oxygen concentration yields a slower AHRR increase rate, a lower peak AHRR value, but a higher AHRR value during the burn-out stage when compared with higher ambient oxygen concentration conditions. OH* chemiluminescence and NL contours indicate that biodiesel may experience a longer premixed-combustion duration. The 18% ambient O2 condition works better for biodiesel than diesel in reducing soot luminosity. With 12% O2, diesel combustion is significantly degraded. However, both fuels experience low temperature combustion at 10% O2. These results may imply that biodiesel is able to achieve the desired lower soot production under a moderate oxygen level with higher combustion efficiency, while diesel needs to be burned under very low ambient oxygen concentration for low soot production. © 2013 Elsevier Ltd.

  5. Trends of Syngas as a Fuel in Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Ftwi Yohaness Hagos

    2014-01-01

    Full Text Available Syngas from biomass and solid waste is a carbon-neutral fuel believed to be a promising fuel for future engines. It was widely used for spark-ignition engines in the WWII era before being replaced with gasoline. In this paper, the technological development, success, and challenges for application of syngas in power generating plants, the trends of engine technologies, and the potential of this fuel in the current engine technology are highlighted. Products of gasification vary with the variation of input parameters. Therefore, three different syngases selected from the two major gasification product categories are used as case studies. Their fuel properties are compared to those of CNG and hydrogen and the effects on the performance and emissions are studied. Syngases have very low stoichiometric air-fuel ratio; as a result they are not suitable for stoichiometric application. Besides, syngases have higher laminar flame speed as compared to CNG. Therefore, stratification under lean operation should be used in order to keep their performance and emissions of NOx comparable to CNG counterpart. However, late injection stratification leads to injection duration limitation leading to restriction of output power and torque. Therefore, proper optimization of major engine variables should be done in the current engine technology.

  6. Design of a single cylinder optical access to the combustion engine Scania D12

    Energy Technology Data Exchange (ETDEWEB)

    Fuchs, Juergen

    2000-11-01

    In this work a maximum optical access to a diesel engine is developed. The combustion-process in the engine should be representative to the one in a standard engine, so the geometry of the combustion chamber is modified as little as possible. A Scania single cylinder, 2-litre engine was subjected to modifications allowing the optical access. Solutions to these problems are obtained by using the method of Product-Development, mainly based on the literature by Prof Dr.-Ing. Birkhofer at the Technical University of Darmstadt, Germany. An optical engine design of the Bowditch type was the chosen main working principle. This engine contains an extended cylinder, partly made of glass, a glass piston-crown and a mirror placed inside the extended piston. The laser sheet is led into the combustion chamber through the glass part of the cylinder, then gets reflected inside the combustion chamber and is led through the glass piston crown and via the mirror out of the engine. A redesign of the valve-train, using extended push-rods, is necessary. The demand to examine the combustion at Top-Dead-Centre (TDC) and the necessity of supporting the glass, give the reasons to do work on the cylinder head. This in return brings sealing problems, which have been solved. Another problem that occurs with that type of engine is that is has to run without oil-lubrication. Piston rings made of Rylon are used to solve this problem. A special feature of the engine that has been constructed here is that the inner surface of the glass may be cleaned without removing the cylinder head. This is obtained by a construction with a movable cylinder. In cleaning-state the cylinder is driven up and down together with the piston, while the head is supported by an outer structure. When running the engine, the cylinder is fixed to the structure. Furthermore this report contains the necessary calculations and integrity assessments on the critical parts of the construction. All calculations, except the

  7. Towards cleaner combustion engines through groundbreaking detailed chemical kinetic models.

    Science.gov (United States)

    Battin-Leclerc, Frédérique; Blurock, Edward; Bounaceur, Roda; Fournet, René; Glaude, Pierre-Alexandre; Herbinet, Olivier; Sirjean, Baptiste; Warth, V

    2011-09-01

    In the context of limiting the environmental impact of transportation, this critical review discusses new directions which are being followed in the development of more predictive and more accurate detailed chemical kinetic models for the combustion of fuels. In the first part, the performance of current models, especially in terms of the prediction of pollutant formation, is evaluated. In the next parts, recent methods and ways to improve these models are described. An emphasis is given on the development of detailed models based on elementary reactions, on the production of the related thermochemical and kinetic parameters, and on the experimental techniques available to produce the data necessary to evaluate model predictions under well defined conditions (212 references). This journal is © The Royal Society of Chemistry 2011

  8. ABC - alcohol based combustion engines. Challenges and opportunities

    Energy Technology Data Exchange (ETDEWEB)

    Bergstroem, K.; Nordin, H.; Koenigstein, A. [GM Powertrain Europe (Austria); Marriott, C.D.; Wiles, M.A. [GM Powertrain North America (United States)

    2007-07-01

    Ethanol as a fuel for individual transportation represents one answer to the future challenges regarding energy availability, energy accessibility and environmental compatibility. In the first generation of flex-fuel engines (an engine capable of operating with different ethanol blends) the challenge was to modify existing hardware in order to make the engines durable in a more aggressive environment (corrosion, wear) of ethanol, and to have controls available to run w/ different ethanol blends. Besides the significant improvement in CO{sub 2}-emissions, especially if considered on a well-to-wheels basis, quite significant improvements in regard to full-load performance were achieved. With the next generation of flex-fuel engines, based on state-of-the-art SIDI turbo technology, full-load efficiency (i.e. fuel consumption) can be further improved, since these engines are already designed for higher in-cylinder peak pressures. Full potential will be gained if there will be a dedicated design for flex-fuel engines, enabling peak pressures of about 120 bar. With this capability the full-load fuel consumption can be reduced by an additional 10%, without being penalized by fuel enrichment demands for component protection purposes. As an alternative, maximum peak pressure and full-load fuel consumption can be kept constant while increasing the compression ratio to CR=11-12 in order to address part-load fuel consumption. Such a compression ratio has never been seen before on a turbo charged engine. Before this becomes a standard technology further efforts have to be spent in order to provide sufficient infrastructure/fuelling stations on a European basis. Sweden represents a good example of how this technology can be implemented - but Sweden alone is not sufficient to make this a success story. Promotion by the European government and the regional governments is required as well. (orig.)

  9. Co-combustion of biodiesel with oxygenated fuels in direct injection diesel engine

    Directory of Open Access Journals (Sweden)

    Tutak Wojciech

    2017-01-01

    Full Text Available The paper presents results of experimental investigation of cocombustion process of biodiesel (B100 blended with oxygenated fuels with 20% in volume. As the alternative fuels ware used hydrated ethanol, methanol, 1-butanol and 2-propanol. It was investigated the influence of used blends on operating parameters of the test engine and exhaust emission (NOx, CO, THC, CO2. It is observed that used blends are characterized by different impact on engine output power and its efficiency. Using biodiesel/alcohol blend it is possible to improve engine efficiency with small drop in indicated mean effective pressure (IMEP. Due to combustion characteristic of biodiesel/alcohol obtained a slightly larger specific NOx emission. It was also observed some differences in combustion phases due to various values of latent heat of evaporation of used alcohols and various oxygen contents. Test results confirmed that the combustion process occurring in the diesel engine powered by blend takes place in a shorter time than in the typical diesel engine.

  10. Performance Evaluation of an Ultra-Lean Combustion Studies in IC Engines

    Directory of Open Access Journals (Sweden)

    Puli Ravi Kumar

    2016-01-01

    Full Text Available An investigation was made to determine the effects of ethanol at ultra-lean effective systems utilizing an experimental study. The present study is planned to develop and evaluate the performance, emission and combustion characteristics of the ultra-lean burn Internal Combustion engine was modified to operate on ethanol blends fuels. The study looked at part throttle, constant speed operation of 0%, 10%, and 15% ethanol blends with gasoline mixtures operating in ultra-lean operating systems. In experiment practice the use of homogeneous lean mixtures in engine has been handicapped by several difficulties. The most serious one is that the flame propagation through mixtures becomes gradually slower as the mixture becomes leaner. The mixture distribution in a multi-cylinder engine is a problem because even small variation in mixture ratio on the linear side will strongly effect power output. Enhancement of lean combustion of homogeneous mixtures can be achieved by (i using ethanol blends with gasoline (ii using high-ignition energy (iii providing high compression ratios (iv creating high swirl in the combustion chamber.

  11. Combustion, Performance and Emission Analysis of an Oxygen-Controlling Downsized SI Engine

    Directory of Open Access Journals (Sweden)

    Zhou J.X.

    2016-07-01

    Full Text Available In the present study, experiments were carried out in a single-cylinder downsized SI engine with different rates of oxygen (15% to 27% by volume in the total mixture of intake gases except fuel and equivalence ratios (from 0.45 to 1. Therefore, the oxygen volume fraction is due to oxygen enrichment or nitrogen dilution. The study of the impact of controlling the oxygen concentration on the combustion characteristics and emissions was performed at 1 400 rpm, at several loads (Indicated Mean Effective Pressure (IMEP from 400 to 1 000 kPa. For each operation point, the spark advance and the intake pressure were adjusted simultaneously in order to maintain the load and obtain a minimum value of the indicated Specific Fuel Consumption (SFC. The effect of the oxygen concentration on the engine combustion characteristics was simulated by using the commercial software AMESim, with the combustion model developed by IFP Energies nouvelles, and an adapted algorithm was used to avoid residual gas calibration. By implementing a correlation for the laminar burning velocity, the in-cylinder pressures were perfectly predicted with a maximum pressure relative error of less than 2% for almost all the operating points. The classification of engine combustion according to the Peters-Borghi diagram, gives a deeper insight into the interaction between turbulence and the flame front.

  12. Effects of Fischer-Tropsch diesel fuel on combustion and emissions of direct injection diesel engine

    Institute of Scientific and Technical Information of China (English)

    Yongcheng HUANG; Shangxue WANG; Longbao ZHOU

    2008-01-01

    Effects of Fischer-Tropsch (F-T) diesel fuel on the combustion and emission characteristics of a single-cylinder direct injection diesel engine under different fuel delivery advance angles were investigated. The experi-mental results show that F-T diesel fuel exhibits shorter ignition delay, lower peak values of premixed burning rate, lower combustion pressure and pressure rise rate, and higher peak value of diffusion burning rate than con-ventional diesel fuel when the engine remains unmodified. In addition, the unmodified engine with F-T diesel fuel has lower brake specific fuel consumption and higher effective thermal efficiency, and presents lower HC, CO, NOx and smoke emissions than conventional diesel fuel. When fuel delivery advance angle is retarded by 3 crank angle degrees, the combustion duration is obviously shor-tened; the peak values of premixed burning rate, the com-bustion pressure and pressure rise rate are further reduced; and the peak value of diffusion burning rate is further increased for F-T diesel fuel operation, Moreover, the retardation of fuel delivery advance angle results in a further significant reduction in NOx emissions with no penalty on specific fuel consumption and with much less penalty on HC, CO and smoke emissions.

  13. Combustion characteristics of a direct-injection diesel engine fueled with Fischer-Tropsch diesel

    Institute of Scientific and Technical Information of China (English)

    HUANG Yongcheng; ZHOU Longbao; PAN Keyu

    2007-01-01

    Fischer-Tropsch (F-T) diesel fuel is characterized by a high cetane number, a near-zero sulphur content and a very low aromatic level. On the basis of the recorded incylinder pressures and injector needle lifts, the combustion characteristics of an unmodified single-cylinder directinjection diesel engine operating on F-T diesel fuel are analyzed and compared with those of conventional diesel fuel operation. The results show that F-T diesel fuel exhibits a slightly longer injection delay and injection duration, an average of 18.7% shorter ignition delay, and a comparable total combustion duration when compared to those of conventional diesel fuel. Meanwhile, F-T diesel fuel displays an average of 26.8% lower peak value of premixed burning rate and a higher peak value of diffusive burning rate. In addition, the F-T diesel engine has a slightly lower peak combustion pressure, a far lower rate of pressure rise, and a lower mechanical load and combustion noise than the conventional diesel engine. The brake specific fuel consumption is lower and the effective thermal efficiency is higher for F-T diesel fuel operation.

  14. A Technical Review of Compressed Natural Gas as an Alternative Fuel for Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Semin

    2008-01-01

    Full Text Available Natural gas is promising alternative fuel to meet strict engine emission regulations in many countries. Compressed natural gas (CNG has long been used in stationary engines, but the application of CNG as a transport engines fuel has been considerably advanced over the last decade by the development of lightweight high-pressure storage cylinders. Engine conversion technology is well established and suitable conversion equipment is readily available. For spark ignition engines there are two options, a bi-fuel conversion and use a dedicated to CNG engine. For compression ignition engines converted to run on natural gas, there are two main options discussed, there are dual-fuel engines and normal ignition can be initiated. Natural gas engines can operate at lean burn and stoichiometric conditions with different combustion and emission characteristics. In this paper, the CNG engines research and development fueled using CNG are highlighted to keep the output power, torque and emissions of natural gas engines comparable to their gasoline or diesel counterparts. The high activities for future CNG engines research and development to meet future CNG engines is recorded in the paper.

  15. Multi-dimensional Modeling of the Application of Catalytic Combustion to Homogeneous Charge Compression Ignition Engine

    Institute of Scientific and Technical Information of China (English)

    Wen Zeng; MaoZhao Xie

    2006-01-01

    The detailed surface reaction mechanism of methane on rhodium catalyst was analyzed.Comparisons between numerical simulation and experiments showed a basic agreement.The combustion process of homogeneous charge compression ignition (HCCI) engine whose piston surface has been coated with catalyst (rhodium and platinum) was numerically investigated.A multi-dimensional model with detailed chemical kinetics was built.The effects of catalytic combustion on the ignition timing,the temperature and CO concentration fields,and HC,CO and NOx emissions of the HCCI engine were discussed.The results showed the ignition timing of the HCCI engine was advanced and the emissions of HC and CO were decreased by the catalysis.

  16. Comparison of an Internal Combustion Engine Derating Operated on Producer Gas from Coal and Biomass Gasification

    Directory of Open Access Journals (Sweden)

    Muhammad Ade Andriansyah Efendi

    2016-06-01

    Full Text Available Gasification is an effective and clean way to convert coal and biomass into useful fuels and chemical feedstocks. Producer gas utilization for internal combustion engine has been studied, not only from biomass gasification but also from coal gasification. This paper compares the research that has done author using coal gasification with other research results using biomass gasification. Coal gasifier performance test conducted with capacity of 20 kg/h coal. The proximate and ultimate analysis of raw coal, ash product and producer gas was conducted and comparised. The result of analysis shows that the efficiency of the coal gasification was 61% while range of gasifier efficiency for biomass is between 50-80%. Meanwhile, the experimental results on the performance of internal combustion engines using gas producer shows that the derating for power generation using coal producer gas was 46% and biomass was 20-50% depend on compression ratio of engine and characteristic of producer gas. 

  17. Investigation on effect of equivalence ratio and engine speed on homogeneous charge compression ignition combustion using chemistry based CFD code

    Directory of Open Access Journals (Sweden)

    Ghafouri Jafar

    2014-01-01

    Full Text Available Combustion in a large-bore natural gas fuelled diesel engine operating under Homogeneous Charge Compression Ignition mode at various operating conditions is investigated in the present paper. Computational Fluid Dynamics model with integrated chemistry solver is utilized and methane is used as surrogate of natural gas fuel. Detailed chemical kinetics mechanism is used for simulation of methane combustion. The model results are validated using experimental data by Aceves, et al. (2000, conducted on the single cylinder Volvo TD100 engine operating at Homogeneous Charge Compression Ignition conditions. After verification of model predictions using in-cylinder pressure histories, the effect of varying equivalence ratio and engine speed on combustion parameters of the engine is studied. Results indicate that increasing engine speed provides shorter time for combustion at the same equivalence ratio such that at higher engine speeds, with constant equivalence ratio, combustion misfires. At lower engine speed, ignition delay is shortened and combustion advances. It was observed that increasing the equivalence ratio retards the combustion due to compressive heating effect in one of the test cases at lower initial pressure. Peak pressure magnitude is increased at higher equivalence ratios due to higher energy input.

  18. Process/Engineering Co-Simulation of Oxy-Combustion and Chemical Looping Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Sloan, David [Alstom Power Inc., Windsor, CT (United States)

    2013-03-01

    Over the past several years, the DOE has sponsored various funded programs, collectively referred to as Advanced Process Engineering Co-Simulator (APECS) programs, which have targeted the development of a steady-state simulator for advanced power plants. The simulator allows the DOE and its contractors to systematically evaluate various power plant concepts, either for preliminary conceptual design or detailed final design.

  19. Combustion Stability Verification for the Thrust Chamber Assembly of J-2X Developmental Engines 10001, 10002, and 10003

    Science.gov (United States)

    Morgan, C. J.; Hulka, J. R.; Casiano, M. J.; Kenny, R. J.; Hinerman, T. D.; Scholten, N.

    2015-01-01

    The J-2X engine, a liquid oxygen/liquid hydrogen propellant rocket engine available for future use on the upper stage of the Space Launch System vehicle, has completed testing of three developmental engines at NASA Stennis Space Center. Twenty-one tests of engine E10001 were conducted from June 2011 through September 2012, thirteen tests of the engine E10002 were conducted from February 2013 through September 2013, and twelve tests of engine E10003 were conducted from November 2013 to April 2014. Verification of combustion stability of the thrust chamber assembly was conducted by perturbing each of the three developmental engines. The primary mechanism for combustion stability verification was examining the response caused by an artificial perturbation (bomb) in the main combustion chamber, i.e., dynamic combustion stability rating. No dynamic instabilities were observed in the TCA, although a few conditions were not bombed. Additional requirements, included to guard against spontaneous instability or rough combustion, were also investigated. Under certain conditions, discrete responses were observed in the dynamic pressure data. The discrete responses were of low amplitude and posed minimal risk to safe engine operability. Rough combustion analyses showed that all three engines met requirements for broad-banded frequency oscillations. Start and shutdown transient chug oscillations were also examined to assess the overall stability characteristics, with no major issues observed.

  20. Research on Measurements for Temperature and Stress of Pistons in Internal Combustion Engine

    Institute of Scientific and Technical Information of China (English)

    DONG Xiao-rui; TAN Jian-song

    2008-01-01

    In both numerical simulation and experimental research for the piston of internal combustion engine, the verification foundations are always insufficient. The reason is the measurements for its transient temperature and stress under actual operation conditions are very difficult. A multi-channel measurement-storage technology is used in the engine bench experiment to measure the piston temperature and stress in real time. The temperature and stress changes in the engine operation process are obtained. They provide reliable instructive criteria for numerical analysis and experiment of the piston working state.

  1. A transient tribodynamic approach for the calculation of internal combustion engine piston slap noise

    Science.gov (United States)

    Dolatabadi, N.; Littlefair, B.; De la Cruz, M.; Theodossiades, S.; Rothberg, S. J.; Rahnejat, H.

    2015-09-01

    An analytical/numerical methodology is presented to calculate the radiated noise due to internal combustion engine piston impacts on the cylinder liner through a film of lubricant. Both quasi-static and transient dynamic analyses coupled with impact elasto-hydrodynamics are reported. The local impact impedance is calculated, as well as the transferred energy onto the cylinder liner. The simulations are verified against experimental results for different engine operating conditions and for noise levels calculated in the vicinity of the engine block. Continuous wavelet signal processing is performed to identify the occurrence of piston slap noise events and their spectral content, showing good conformance between the predictions and experimentally acquired signals.

  2. HEAT RECOVERY FROM A NATURAL GAS POWERED INTERNAL COMBUSTION ENGINE BY CO2 TRANSCRITICAL POWER CYCLE

    Directory of Open Access Journals (Sweden)

    Mahmood Farzaneh-Gord

    2010-01-01

    Full Text Available The present work provides details of energy accounting of a natural gas powered internal combustion engine and achievable work of a utilized CO2 power cycle. Based on experimental performance analysis of a new designed IKCO (Iran Khodro Company 1.7 litre natural gas powered engine, full energy accounting of the engine were carried out on various engine speeds and loads. Further, various CO2 transcritical power cycle configurations have been appointed to take advantages of exhaust and coolant water heat lost. Based on thermodynamic analysis, the amount of recoverable work obtainable by CO2 transcritical power cycles have been calculated on various engine conditions. The results show that as much as 18 kW power could be generated by the power cycle. This would be considerable amount of power especially if compared with the engine brake power.

  3. The research and development of in situ non intrusive optical and temperature diagnostics in an internal combustion engine

    CERN Document Server

    Wilson, T S

    2002-01-01

    Novel instrumentation has been developed and evaluated in a low-cost, purpose built, single-cylinder internal combustion engine test facility designed to simulate many of the combustion features that are common between an internal combustion engine, a gas turbine combustor and a steel rolling furnace. High bandwidth in-cylinder surface temperature measurements are demonstrated with a new application of platinum thin film resistance thermometers. These gauges are exposed to the combustion gases and are mounted to both the cylinder head and piston. It is shown that calculation of flame speed, determination of heat flux levels and flame structure observation are possible. Fibre optic probes capable of high frequency spectral measurements of the combustion emission are presented. The spectral measurements are shown to complement the temperature measurement by being able to differentiate the flame front from the general combustion emission and hot by-products. Beyond this, other optical techniques have been explor...

  4. Three-dimensional modeling of diesel engine intake flow, combustion and emissions-2

    Science.gov (United States)

    Reitz, R. D.; Rutland, C. J.

    1993-01-01

    A three-dimensional computer code, KIVA, is being modified to include state-of-the-art submodels for diesel engine flow and combustion. Improved and/or new submodels which have already been implemented and previously reported are: wall heat transfer with unsteadiness and compressibility, laminar-turbulent characteristic time combustion with unburned HC and Zeldo'vich NO(x), and spray/wall impingement with rebounding and sliding drops. Progress on the implementation of improved spray drop drag and drop breakup models, the formulation and testing of a multistep kinetics ignition model, and preliminary soot modeling results are described. In addition, the use of a block structured version of KIVA to model the intake flow process is described. A grid generation scheme was developed for modeling realistic (complex) engine geometries, and computations were made of intake flow in the ports and combustion chamber of a two-intake-value engine. The research also involves the use of the code to assess the effects of subprocesses on diesel engine performance. The accuracy of the predictions is being tested by comparisons with engine experiments. To date, comparisons were made with measured engine cylinder pressure, temperature and heat flux data, and the model results are in good agreement with the experiments. Work is in progress that will allow validation of in-cylinder flow and soot formation predictions. An engine test facility is described that is being used to provide the needed validation data. Test results were obtained showing the effect of injection rate and split injections on engine performance and emissions.

  5. Optimizing Spray and Combustion in Diesel Engine by Multidimensional Numerical Simulation

    Institute of Scientific and Technical Information of China (English)

    ZHOU Lei; ZHAO Chang-lu; ZHANG Fu-jun

    2005-01-01

    The calculation of spray and combustion in diesel engines is described by using the softwares FIRE and BOOST. The application of the resulting computational method to the simulation of fuel spray and breakup, mixture formation and combustion in a heavy duty diesel is presented. According to detailed insight into the governing processes provided by the simulation results, various aspects of the dependence of the spray propagation and combustion on the chamber geometry and spray angle are discussed. Then, global cylinderaveraged pressure traces are extracted from the space and time resolved field quantities and compared to incylinder pressure measurements. Finally, an optimized configuration of the chamber geometry and spray angle with a new injection rate of higher injection pressure is proposed.

  6. A Preliminary Motion-picture Study of Combustion in a Compression-ignition Engine

    Science.gov (United States)

    Buckley, E C; Waldron, C D

    1934-01-01

    Motion pictures were taken at 1,850 frames per second of the spray penetration and combustion occurring in the N.A.C.A. combustion apparatus arranged to operate as a compression-ignition engine. Indicator cards were taken simultaneously with the motion pictures by means of the N.A.C.A. optical indicator. The motion pictures showed that when ignition occurred during injection it started in the spray envelope. If ignition occurred after injection cut-off, however, and after considerable mixing had taken place, it was impossible to predict where the ignition would start. The pictures also showed that ignition usually started at several points in the combustion chamber. With this apparatus, as the injection advance angle increased from 0 degrees to 40 degrees before top center, the rate of flame spread increased and the duration of the burning decreased.

  7. Combustion characteristics of spark-ignition and pilot flame ignition systems in a model Wankel stratified charge engine

    Energy Technology Data Exchange (ETDEWEB)

    Muroki, T. [Kanagawa Inst. of Technology, Dept. of Mechanical Engineering, Kanagawa (Japan); Moriyoshi, Y. [Chiba Univ., Dept. of Electronics and Mechanical Engineering, Chiba (Japan)

    2000-11-01

    In a stratified charge engine, a glow plug pilot flame ignition system has been compared with a spark-ignition system for a model stratified charge Wankel combustion chamber. A motored two-stroke diesel engine was operated as a rapid compression and expansion machine with the cylinder head replaced by a model Wankel combustion chamber designed to simulate the temporal changes of air flow and pressure fields inside the chamber of an actual engine. It was found that the pilot flame ignition system had better ignitability and improved combustion characteristics, especially in the lean mixture range, relative to the spark-ignition system. (Author)

  8. Brayton cycle for internal combustion engine exhaust gas waste heat recovery

    Directory of Open Access Journals (Sweden)

    J Galindo

    2015-06-01

    Full Text Available An average passenger car engine effectively uses about one-third of the fuel combustion energy, while the two-thirds are wasted through exhaust gases and engine cooling. It is of great interest to automotive industry to recover some of this wasted energy, thus increasing the engine efficiency and lowering fuel consumption and contamination. Waste heat recovery for internal combustion engine exhaust gases using Brayton cycle machine was investigated. The principle problems of application of such a system in a passenger car were considered: compressor and expander machine selection, machine size for packaging under the hood, efficiency of the cycle, and improvement of engine efficiency. Important parameters of machines design have been determined and analyzed. An average 2-L turbocharged gasoline engine’s New European Driving Cycle points were taken as inlet points for waste heat recovery system. It is theoretically estimated that the recuperated power of 1515 W can be achieved along with 5.7% improvement in engine efficiency, at the point where engine power is 26550 W.

  9. Combustion Model and Control Parameter Optimization Methods for Single Cylinder Diesel Engine

    Directory of Open Access Journals (Sweden)

    Bambang Wahono

    2014-01-01

    Full Text Available This research presents a method to construct a combustion model and a method to optimize some control parameters of diesel engine in order to develop a model-based control system. The construction purpose of the model is to appropriately manage some control parameters to obtain the values of fuel consumption and emission as the engine output objectives. Stepwise method considering multicollinearity was applied to construct combustion model with the polynomial model. Using the experimental data of a single cylinder diesel engine, the model of power, BSFC, NOx, and soot on multiple injection diesel engines was built. The proposed method succesfully developed the model that describes control parameters in relation to the engine outputs. Although many control devices can be mounted to diesel engine, optimization technique is required to utilize this method in finding optimal engine operating conditions efficiently beside the existing development of individual emission control methods. Particle swarm optimization (PSO was used to calculate control parameters to optimize fuel consumption and emission based on the model. The proposed method is able to calculate control parameters efficiently to optimize evaluation item based on the model. Finally, the model which added PSO then was compiled in a microcontroller.

  10. Soot filter for the exhaust gas of internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Abthoff, J.; Schuster, H.D.; Langer, H.J.

    1980-06-19

    In the previously known soot filters, the exhaust gas flows through the cylindrical filter radially from the outside to the inside. The exhaust gas touches a relatively large area of the filter housing and therefore loses a large part of the thermal energy required for post-combustion. According to the invention, these disadvantages are avoided in the new filter, where the filter material forms hollow spaces at the internal wall of the filter, which take the exhaust gas after it has flowed through the filter and carry it in an axial direction of the filter housing to the exhaust. Due to this design of the filter and the saving in heat, the areas on which the exhaust gas impinges can be kept appreciably smaller and better use can be made of the heat in the exhaust gas. The ceramic filter material can consist of an outer layer of loose ceramic fibres and an inner woven ceramic fibre mat. In order to increase the effectiveness of the filter, the soot filter can be used as a fine filter after a coarse filter.

  11. Membrane Systems Engineering for Post-combustion Carbon Capture

    KAUST Repository

    Alshehri, Ali

    2013-08-05

    This study proposes a strategy for optimal design of hollow fiber membrane networks for post combustion carbon capture from power plant multicomponent flue gas. A mathematical model describing multicomponent gas permeation through a separation membrane was customized into the flowsheet modeling package ASPEN PLUS. An N-stage membrane network superstructure was defined considering all possible flowsheeting configurations. An optimization formulation was then developed and solved using an objective function that minimizes the costs associated with operating and capital expenses. For a case study of flue gas feed flow rate of 298 m3/s with 13% CO2 and under defined economic parameters, the optimization resulted in the synthesis of a membrane network structure consisting of two stages in series. This optimal design was found while also considering feed and permeate pressures as well as recycle ratios between stages. The cost of carbon capture for this optimal membrane network is estimated to be $28 per tonne of CO2 captured, considering a membrane permeance of 1000 GPU and membrane selectivity of 50. Following this approach, a reduction in capture cost to less than $20 per tonne CO2 captured is possible if membranes with permeance of 2000 GPU and selectivity higher than 70 materialize.

  12. Design Analysis and Optimization of Internal Combustion Engine Piston using CAE tool ANSYS

    Directory of Open Access Journals (Sweden)

    Aditya Kumar Gupta

    2014-11-01

    Full Text Available In the internal combustion engine there are many reciprocating parts which are responsible for giving the motion to the engine. from them the piston is very important part of the internal combustion engine.. The working condition of the piston is so worst in comparison of other parts of the internal combustion engine. There is very high probability to failure of the piston due to high wear and tear. So there is necessary to inspection the working condition of piston. In before there is no availability of software packages. So there is difficult to check out the failure of the piston, it is also very time taken process. In now days the software packages are used to consume less time and give quality assurance. In this study work there are two steps of analysis of the piston they are Designing and Analysis. Firstly design the model of the piston in giving design specification on the modelling software like INVENTOR . Then giving it the constraints which are act on the working condition of the piston after import the model of the piston into the analysis software ANSYS in IGES format. Then the analysis become completed on the different parameters(temperature, stress, deformation and easily analysis the result. In this work the piston become optimized after the reducing the material of the piston. the mass and volume of the piston become reduced. The deformation also increased after the optimization which is responsible for the stress distribution on the piston head or piston crown.

  13. Biomass Power Generation through Direct Integration of Updraft Gasifier and Stirling Engine Combustion System

    Directory of Open Access Journals (Sweden)

    Jai-Houng Leu

    2010-01-01

    Full Text Available Biomass is the largest renewable energy source in the world. Its importance grows gradually in the future energy market. Since most biomass sources are low in energy density and are widespread in space, small-scale biomass conversion system is therefore more competitive than a large stand-alone conversion plant. The current study proposes a small-scale solid biomass power system to explore the viability of direct coupling of an updraft fixed bed gasifier with a Stirling engine. The modified updraft fixed bed gasifier employs an embedded combustor inside the gasifier to fully combust the synthetic gas generated by the gasifier. The flue gas produced by the synthetic gas combustion inside the combustion tube is piped directly to the heater head of the Stirling engine. The engine will then extract and convert the heat contained in the flue gas into electricity automatically. Output depends on heat input. And, the heat input is proportional to the flow rate and temperature of the flue gas. The preliminary study of the proposed direct coupling of an updraft gasifier with a 25 kW Stirling engine demonstrates that full power output could be produced by the current system. It could be found from the current investigation that no auxiliary fuel is required to operate the current system smoothly. The proposed technology and units could be considered as a viable solid biomass power system.

  14. Combustion, emission and engine performance characteristics of used cooking oil biodiesel - A review

    Energy Technology Data Exchange (ETDEWEB)

    Enweremadu, C.C. [Department of Mechanical Engineering, Vaal University of Technology, Private Bag X021, Vanderbijlpark 1900 (South Africa); Rutto, H.L. [Department of Chemical Engineering, Vaal University of Technology, Private Bag X021, Vanderbijlpark 1900 (South Africa)

    2010-12-15

    As the environment degrades at an alarming rate, there have been steady calls by most governments following international energy policies for the use of biofuels. One of the biofuels whose use is rapidly expanding is biodiesel. One of the economical sources for biodiesel production which doubles in the reduction of liquid waste and the subsequent burden of sewage treatment is used cooking oil (UCO). However, the products formed during frying, such as free fatty acid and some polymerized triglycerides, can affect the transesterification reaction and the biodiesel properties. This paper attempts to collect and analyze published works mainly in scientific journals about the engine performance, combustion and emissions characteristics of UCO biodiesel on diesel engine. Overall, the engine performance of the UCO biodiesel and its blends was only marginally poorer compared to diesel. From the standpoint of emissions, NOx emissions were slightly higher while un-burnt hydrocarbon (UBHC) emissions were lower for UCO biodiesel when compares to diesel fuel. There were no noticeable differences between UCO biodiesel and fresh oil biodiesel as their engine performances, combustion and emissions characteristics bear a close resemblance. This is probably more closely related to the oxygenated nature of biodiesel which is almost constant for every biodiesel (biodiesel has some level of oxygen bound to its chemical structure) and also to its higher viscosity and lower calorific value, which have a major bearing on spray formation and initial combustion. (author)

  15. Future combustion methods for biomethane powered tractor engines; Zukuenftige Brennverfahren fuer biomethanbetriebene Traktormotoren

    Energy Technology Data Exchange (ETDEWEB)

    Prehn, Sascha; Harndorf, Horst [Rostock Univ. (Germany). Lehrstuhl fuer Kolbenmaschinen und Verbrennungsmotoren; Wichmann, Volker [Rostock Univ. (Germany). Maschinenlabor; Beberdick, Wolfgang

    2016-08-01

    Biomethane represents an alternative to fossil fuels (petrol, diesel), not only in the on-road sector. Methane-based fuels come in focus of farmers in the agriculture sector, due to cost constraints, increasing regulation of pollutant emissions and reduction of carbondioxid. To represent a monovalent gas operation, a functional model is derived from a series diesel engine for agricultural use. On the test engine, systematic studies on the combustion process are carried out by cylinder pressure indication and exhaust-emission measurement. Combustion under stoichiometric conditions (with or without exhaust gas recirculation) as well as the conversion of fuel from excess air is observed. The study shows that with a natural-gas engine, a complex post-treatment system of exhaust gas (DOC + DPF + SCR) that is typically for diesel engines can be dispensed with. The exhaust gas limits in force since 2014 and a limitation of methane on 0,5 g/kWh can be met with a stoichiometric combustion concept and a three way catalytic converter optimized for the methane oxidation.

  16. Hydrogen-Assisted IC Engine Combustion as a Route to Hydrogen Implementation

    Energy Technology Data Exchange (ETDEWEB)

    Andre Boehman; Daniel Haworth

    2008-09-30

    The 'Freedom Car' Initiative announced by the Bush Administration has placed a significant emphasis on development of a hydrogen economy in the United States. While the hydrogen-fueled fuel-cell vehicle that is the focus of the 'Freedom Car' program would rely on electrochemical energy conversion, and despite the large amount of resources being devoted to its objectives, near-term implementation of hydrogen in the transportation sector is not likely to arise from fuel cell cars. Instead, fuel blending and ''hydrogen-assisted'' combustion are more realizable pathways for wide-scale hydrogen utilization within the next ten years. Thus, a large potential avenue for utilization of hydrogen in transportation applications is through blending with natural gas, since there is an existing market for natural-gas vehicles of various classes, and since hydrogen can provide a means of achieving even stricter emissions standards. Another potential avenue is through use of hydrogen to 'assist' diesel combustion to permit alternate combustion strategies that can achieve lower emissions and higher efficiency. This project focused on developing the underlying fundamental information to support technologies that will facilitate the introduction of coal-derived hydrogen into the market. Two paths were envisioned for hydrogen utilization in transportation applications. One is for hydrogen to be mixed with other fuels, specifically natural gas, to enhance performance in existing natural gas-fueled vehicles (e.g., transit buses) and provide a practical and marketable avenue to begin using hydrogen in the field. A second is to use hydrogen to enable alternative combustion modes in existing diesel engines, such as homogeneous charge compression ignition, to permit enhanced efficiency and reduced emissions. Thus, this project on hydrogen-assisted combustion encompassed two major objectives: (1) Optimization of hydrogen-natural gas mixture

  17. Understanding Combustion and Soot Formation in Diesel Engines

    Science.gov (United States)

    2016-09-09

    report, only a brief summary of major findings are summarized. Temporal evolution of a sooting flame Figure 1-1 portrays the temporal...diesel engine during this soot sampling experiment. The images on the top and mid rows suggest that sooting flame develops on the fuel jet...cylinder liner window (i.e. side-view images) indicate that the sooting flame breaks into two soot pockets upon the impingement on the bowl wall and

  18. Creating mechanisms of toxic substances emission of combustion engines

    Directory of Open Access Journals (Sweden)

    Jankowski Antoni

    2015-12-01

    Full Text Available The paper analyses the mechanisms of creation of toxic exhaust gases, which mainly derived from inexact fuel metering and improper air-fuel mixture preparation. The paper describes the process of creating toxic components in the exhaust gases of piston engines during engine operation, and impact on the emission of these components determining the composition of the fuel mixture determined equivalence factor Φ. The principal mechanisms of formation of toxic exhaust gases, in particular nitrogen oxides, carbon monoxide and hydrocarbons, and also essential according to create each of toxic exhaust gases are the subject of the paper. Moreover, empirical relationships, by means of which it is possible to determine the time of creation of the individual components of toxic exhaust gases, are presented. For example, one of the mechanisms for prompt formation of nitrogen oxides and hydrocarbons graphic illustration of formation as a function of crank angle is described. At the conclusion, the summary and significance of information on creation mechanisms of toxic components in the exhaust gases of piston engines are presented.

  19. Effect of intake pipe on the volumetric efficiency of an internal combustion engine

    Science.gov (United States)

    Capetti, Antonio

    1929-01-01

    The writer discusses the phenomena of expansion and compression which alternately take place in the cylinders of four-stroke engines during the induction process at a high mean piston speed due to the inertia and elasticity of the mixture in the intake pipe. The present paper is intended to demonstrate theoretically the existence of a most favorable pipe length for charging.

  20. HYDROGEN ADDITION ON COMBUSTION AND EMISSION CHARACTERISTICS OF HIGH SPEED SPARK IGNITION ENGINE- AN EXPERIMENTAL STUDY

    Directory of Open Access Journals (Sweden)

    SHIVAPRASAD K. V.

    2016-11-01

    Full Text Available The present article aims at characterizing the combustion and emission parameters of a single cylinder high speed SI engine operating with different concentrations of hydrogen with gasoline fuel. The conventional carburetted SI engine was modified into an electronically controllable engine, wherein ECU was used to control the injection timings and durations of gasoline. The engine was maintained at a constant speed of 3000 rpm and wide open throttle position. The experimental results demonstrated that heat release rate and cylinder pressure were increased with the addition of hydrogen until 20%. The CO and HC emissions were reduced considerably whereas NOx emission was increased with the addition of hydrogen in comparison with pure gasoline engine operation.

  1. Combustion Characteristics of a Diesel Engine Using Propanol Diesel Fuel Blends

    Science.gov (United States)

    Muthaiyan, Pugazhvadivu; Gomathinayagam, Sankaranarayanan

    2016-07-01

    The objective of the work is to study the use of propanol diesel blends as alternative fuel in a single cylinder diesel engine. In this work, four different propanol diesel blends containing 10, 15, 20 and 25 % propanol in diesel by volume were used as fuels. Load tests were conducted on the diesel engine and the combustion parameters such as cylinder gas pressure, ignition delay, rate of heat release and rate of pressure rise were investigated. The engine performance and emission characteristics were also studied. The propanol diesel blends showed longer ignition delay, higher rates of heat release and pressure rise. The thermal efficiency of the engine decreased marginally with the use of fuel blends. The propanol diesel blends decreased the CO, NOX and smoke emissions of the engine considerably.

  2. Studies of some phenomena in control engineering projects - With application to precipitation processes

    Energy Technology Data Exchange (ETDEWEB)

    Stoele-Hansen, Kjell

    1998-12-31

    This thesis deals with the life-cycle of a control engineering project and some phenomena encountered in such projects. Different types of control strategies are discussed and an attempt is made to classify them into categories. Some case projects are presented and forms the basis for discussing the individual`s role in a change project. Further conditions for successful implementation of new control strategies are discussed in general, but also conditions for successful implementation of new control strategies at a process section of a nickel work. Procedures for implementing new control strategies are treated and some remarks are made about operation of control strategies. An introduction is given to the modelling of precipitation in pH systems and different model formulations are discused. The modelling of pH controlled precipitations is discussed in general. A variety of dynamic models, ranging from complex to simple, are proposed and discussed. A rigorous dynamic nonlinear mechanistic model of a precipitation reactor is developed. It is based on the theory of reaction invariants and variants. The model is verified against real process data. The dynamics and characteristics of the precipitation reactor are analysed and some remarks are made with respect to controllability. A new strategy for pH control is proposed. A new model based strategy for controlling the precipitation reactions is also proposed. 93 refs., 63 figs., 10 tabs.

  3. COMBUSTION CHARACTERISTICS OF CI ENGINE USING KARANJA BIODIESEL BLENDS AS FUEL

    Directory of Open Access Journals (Sweden)

    H.A. PHADTARE

    2013-05-01

    Full Text Available Karanja based bio-diesel is a non-edible, biodegradable fuel suitable for diesel engines. Karanja biodiesel has been prepared by transesterification method. Biodiesel-diesel blends have been prepared on volume basis. Physical properties of Karanja biodiesel, diesel and its blends have been determined. An experimentalinvestigation has been carried out to analyze combustion characteristics of a single cylinder, VCR diesel engine fuelled with Karanja biodiesel and its blends (10%, 20%, 30%, 50% and 75% with neat diesel. A series of engine tests, with CR 16.5, 17.5 and 18.5 have been conducted using each of the above blends for comparativeevaluation. Combustion parameters such as ignition delay, peak pressure development, heat release rate analysis of engine have been studied. The results of the experiment in each case have been compared with baseline data of neat diesel. Ignition delays of bio-diesel blends are lower than that of diesel; peak pressure takes place definitely after TDC for safe and efficient operation. Comparable rate of pressure rise obtained is indicative of stable and noise free operation of CI engines with karanja biodiesel blends. B10 is suitable alternative fuel for diesel at slightly higher CR can be used without any engine modifications.

  4. UV laser spectroscopic measurements in jet engine combustion exit flows

    Energy Technology Data Exchange (ETDEWEB)

    Shirley, J.A. (United Technologies Research Center, East Hartford, CT (United States))

    1992-01-01

    Laser diagnostic measurements, which are excited with a narrowband krypton fluoride laser, have been made at the exit of a jet engine combustor. Spectra of Raman scattering and laser induced fluorescence were measured with a 0.5 meter spectrograph equipped with a diode array detector. For these demonstration tests, the combustor was operated at two flow rates including conditions corresponding to the 90 percent power level, with jet fuel and methane. Nitrogen Raman spectra are free of band interference. However, the signal levels are lower than expected. Sources of signal losses are discussed. 27 refs.

  5. Internal combustion engine for vehicles with automatic gearbox. Brennkraftmaschine fuer Kraftfahrzeuge mit einem automatischen Getriebe

    Energy Technology Data Exchange (ETDEWEB)

    Hetmann, R.

    1982-04-19

    The invention refers to an internal combustion engine for vehicles with an automatic gearbox, where the internal combustion engine has a first group of cylinders and at least one second group of cylinders, and a device for affecting the fuel supply to the groups of cylinders, depending on the working parameters of the vehicle. The invention is characterised by the fact that the working parameters are the handbrake and footbrake of the vehicle, and that the device for affecting the fuel supply to the groups of cylinders when the footbrake or handbrake is operated makes it possible to supply fuel to only part of the groups of cylinders. The control switches of both braking systems are connected to the fuel supply control via a logic circuit. This arrangement of the system prevents damage when testing the braking speed of the automatic gearbox due to excessive loads.

  6. Combustion parameters of spark ignition engine using waste potato bioethanol and gasoline blended fuels

    Science.gov (United States)

    Ghobadian, B.; Najafi, G.; Abasian, M.; Mamat, R.

    2015-12-01

    The purpose of this study is to investigate the combustion parameters of a SI engine operating on bioethanol-gasoline blends (E0-E20: 20% bioethanol and 80% gasoline by volume). A reactor was designed, fabricated and evaluated for bioethanol production from potato wastes. The results showed that increasing the bioethanol content in the blend fuel will decrease the heating value of the blended fuel and increase the octane number. Combustion parameters were evaluated and analyzed at different engine speeds and loads (1000-5000 rpm). The results revealed that using bioethanol-gasoline blended fuels will increase the cylinder pressure and its 1st and 2nd derivatives (P(θ), P•(θ) and P••(θ)). Moreover, using bioethanol- gasoline blends will increase the heat release (Q•(θ)) and worked of the cycle. This improvement was due to the high oxygen percentage in the ethanol.

  7. Cooling system in a rotary piston internal combustion engine. Kuehlsystem einer Rotationskolbenbrennkraftmaschine

    Energy Technology Data Exchange (ETDEWEB)

    Eiermann, D.; Nuber, R.

    1991-05-23

    Cooling system of a trochoid-type rotary piston internal combustion engine with a liquid-cooled casing. First the coolant is conducted isochronically and in parallel through cooling chambers of the jacket and a side part of the casing from where it is transported by a cooling pump through the cooling chambers of the other side part, on past a thermostat and into a cooler positioned on this other side part. The cooler consists of a parallel connected pipe bundle whose finned pipes follow the radial outer contours of the casing of the machine. From the cooler the coolant is conducted back into the cooling chambers of the first side part and the jacket. A blower fitted on the eccentric shaft of the internal combustion engine inside the cooler takes in fresh air axially and discharges it radially through the finned pipes.

  8. A new HVAC system based on cogeneration by an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Lazzarin, R.M [Instituto di Ingegneria Gestionale, Universita di Padova, Vicenza (Italy); Longo, G.A.; Romagnoni, P.C. [Istituto di Fisica Technica, Universita di Padova, Padova (Italy)

    1997-06-01

    A new HVAC system is proposed and studied. The plant consists of a reciprocating internal combustion gas engine, producing electrical energy with heat recovery from the jacket water heat and the exhaust. The electricity serves lighting, emf for the building and individual room reversible air-water heat pumps that satisfy mainly sensible cooling and a fraction of the winter heating load. An open cycle absorption system which treats the primary air meets the summer latent load and year round ventilation requirements. In winter the system operates as an open cycle heat pump. The regeneration of the sorbent is obtained by the internal combustion engine heat recovery. The proposed system is analyzed comparing its performance with a traditional plant both in summer and winter mode. 8 refs.

  9. Screening analysis and selection of emission reduction concepts for intermittent combustion aircraft engines

    Science.gov (United States)

    Rezy, B. J.; Meyers, J. E.; Tucker, J. R.; Stuckas, S. J.

    1976-01-01

    An analysis was conducted to screen, evaluate, and select three engine exhaust emission reduction concepts from a group of 14 candidate alternatives. A comprehensive literature search was conducted to survey the emission reduction technology state-of-the-art and establish contact with firms working on intermittent combustion engine development and pollution reduction problems. Concept development, advantages, disadvantages, and expected emission reduction responses are stated. A set of cost effectiveness criteria was developed, appraised for relative importance, and traded off against each concept so that its merit could be determined. A decision model was used to aid the evaluators in managing the criteria, making consistent judgements, calculating merit scores, and ranking the concepts. An Improved Fuel Injection System, Improved Cooling Combustion Chamber, and a Variable Timing Ignition System were recommended to NASA for approval and further concept development. An alternate concept, Air Injection, was also recommended.

  10. A Study of the Theoretical Potential of Thermochemical Exhaust Heat Recuperation for Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Chakravarthy, Veerathu K [ORNL; Daw, C Stuart [ORNL; Pihl, Josh A [ORNL; Conklin, Jim [ORNL

    2010-01-01

    We present a detailed thermodynamic analysis of thermochemical recuperation (TCR) applied to an idealized internal combustion engine with single-stage work extraction. Results for several different fuels are included. For a stoichiometric mixture of methanol and air, TCR can increase the estimated ideal engine Second Law efficiency by about 3% for constant pressure reforming and over 5% for constant volume reforming. For ethanol and isooctane the estimated Second Law efficiency increases for constant volume reforming are 9% and 11%, respectively. The Second Law efficiency improvements from TCR result primarily from the higher intrinsic exergy of the reformed fuel and pressure boost associated with gas mole increase. Reduced combustion irreversibility may also yield benefits for future implementations of combined cycle work extraction.

  11. A Study of the Theoretical Potential of Thermochemical Exhaust Heat Recuperation in Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C Stuart [ORNL; Pihl, Josh A [ORNL; Chakravarthy, Veerathu K [ORNL; Conklin, Jim [ORNL

    2010-01-01

    A detailed thermodynamic analysis of thermochemical recuperation (TCR) applied to an idealized internal combustion engine with single-stage work extraction is presented. Results for several different fuels are included. For a stoichiometric mixture of methanol and air, TCR can increase the estimated ideal engine second law efficiency by about 3% for constant pressure reforming and over 5% for constant volume reforming. For ethanol and isooctane, the estimated second law efficiency increases for constant volume reforming are 9 and 11%, respectively. The second law efficiency improvements from TCR result primarily from the higher intrinsic exergy of the reformed fuel and pressure boost associated with the gas mole increase. Reduced combustion irreversibility may also yield benefits for future implementations of combined cycle work extraction.

  12. Heat transfer in rocket engine combustion chambers and regeneratively cooled nozzles

    Science.gov (United States)

    1993-01-01

    A conjugate heat transfer computational fluid dynamics (CFD) model to describe regenerative cooling in the main combustion chamber and nozzle and in the injector faceplate region for a launch vehicle class liquid rocket engine was developed. An injector model for sprays which treats the fluid as a variable density, single-phase media was formulated, incorporated into a version of the FDNS code, and used to simulate the injector flow typical of that in the Space Shuttle Main Engine (SSME). Various chamber related heat transfer analyses were made to verify the predictive capability of the conjugate heat transfer analysis provided by the FDNS code. The density based version of the FDNS code with the real fluid property models developed was successful in predicting the streamtube combustion of individual injector elements.

  13. 77 FR 37361 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

    Science.gov (United States)

    2012-06-21

    ... Reciprocating Internal Combustion Engines; New Source Performance Standards for Stationary Internal Combustion... Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines.'' The EPA... Internal Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines...

  14. Invited Review. Combustion instability in spray-guided stratified-charge engines. A review

    Energy Technology Data Exchange (ETDEWEB)

    Fansler, Todd D. [Univ. of Wisconsin, Madison, WI (United States); Reuss, D. L. [Univ. of Michigan, Ann Arbor, MI (United States); Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sick, V. [Univ. of Michigan, Ann Arbor, MI (United States); Dahms, R. N. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-02-02

    Our article reviews systematic research on combustion instabilities (principally rare, random misfires and partial burns) in spray-guided stratified-charge (SGSC) engines operated at part load with highly stratified fuel -air -residual mixtures. Results from high-speed optical imaging diagnostics and numerical simulation provide a conceptual framework and quantify the sensitivity of ignition and flame propagation to strong, cyclically varying temporal and spatial gradients in the flow field and in the fuel -air -residual distribution. For SGSC engines using multi-hole injectors, spark stretching and locally rich ignition are beneficial. Moreover, combustion instability is dominated by convective flow fluctuations that impede motion of the spark or flame kernel toward the bulk of the fuel, coupled with low flame speeds due to locally lean mixtures surrounding the kernel. In SGSC engines using outwardly opening piezo-electric injectors, ignition and early flame growth are strongly influenced by the spray's characteristic recirculation vortex. For both injection systems, the spray and the intake/compression-generated flow field influence each other. Factors underlying the benefits of multi-pulse injection are identified. Finally, some unresolved questions include (1) the extent to which piezo-SGSC misfires are caused by failure to form a flame kernel rather than by flame-kernel extinction (as in multi-hole SGSC engines); (2) the relative contributions of partially premixed flame propagation and mixing-controlled combustion under the exceptionally late-injection conditions that permit SGSC operation on E85-like fuels with very low NOx and soot emissions; and (3) the effects of flow-field variability on later combustion, where fuel-air-residual mixing within the piston bowl becomes important.

  15. Method for operating an automobile with a combustion engine with applied ignition

    Energy Technology Data Exchange (ETDEWEB)

    Anderton, R.A.; Smith, R.R.; Tippler, R.

    1982-01-28

    A method is proposed to operate automobiles with combustion engines with applied ignition directly after the assembly on a petrol-mineral oil mixture; this prevents a spark plug fouling when the cars which hare just been completed are operated on short distances only. This petrol-mineral oil mixture should consist preferably of 95-98 ROZ petrol and mineral oil share of less than 5 vol.% preferably 0,5 vol.%.

  16. Mechanical and thermal analysis of the internal combustion engine piston using Ansys

    Science.gov (United States)

    Cioată, V. G.; Kiss, I.; Alexa, V.; Raţiu, S. A.

    2017-01-01

    The piston is one of the most important components of the internal combustion engine. Piston fail mainly due to mechanical stresses and thermal stresses. In this paper is determined by using the finite element method, stress and displacement distribution due the flue gas pressure and temperature, separately and combined. The FEA is performed by CAD and CAE software. The results are compared with those obtained by the analytical method and conclusions have been drawn.

  17. On the wall jet from the ring crevice of an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Cloutman, L.D. [Lawrence Livermore National Lab., CA (United States); Green, R.M. [Sandia National Labs., Livermore, CA (United States)

    1996-05-01

    Numerical simulations and experiments of the jetting of gases from the ring crevices of a laboratory engine shortly after exhaust valve opening showed an unanticipated radial flow of the crevice gases into the main combustion chamber. We report well-resolved numerical simulations of a wall jet that show that this radial motion is driven by vorticity generation in the wall boundary layer and at the corner of the piston crown.

  18. Assessment of ISLOCA risk-methodology and application to a combustion engineering plant

    Energy Technology Data Exchange (ETDEWEB)

    Kelly, D.L.; Auflick, J.L.; Haney, L.N. [EG and G Idaho, Inc., Idaho Falls, ID (United States)

    1992-04-01

    Inter-system loss-of-coolant accidents (ISLOCAs) have been identified as important contributors to offsite risk for some nuclear power plants. A methodology has been developed for identifying and evaluating plant-specific hardware designs, human factors issues, and accident consequence factors relevant to the estimation of ISOLOCA core damage frequency and risk. This report presents a detailed of description of the application of this analysis methodology to a Combustion Engineering plant.

  19. Effectiveness of oxygen enriched hydrogen-HHO gas addition on DI diesel engine performance, emission and combustion characteristics

    National Research Council Canada - National Science Library

    Premkartikkumar S.R; Annamalai K; Pradeepkumar A.R

    2014-01-01

    Nowadays, more researches focus on protecting the environment. Present investigation concern with the effectiveness of Oxygen Enriched hydrogen- HHO gas addition on performance, emission and combustion characteristics of a DI diesel engine...

  20. COMBUSTION AND PERFORMANCE CHARACTERISTICS OF A SMALL SPARK IGNITION ENGINE FUELLED WITH HCNG

    Directory of Open Access Journals (Sweden)

    A. SONTHALIA

    2015-04-01

    Full Text Available Due to environmental concerns and fossil fuel depletion, large scale researches were carried out involving the use of natural gas in internal combustion engines. Natural gas is a clean burning fuel that is available from large domestic natural reserve. When it is used as a fuel in SI engines, it reduces emissions to meet EURO-III norms with carburettors and EURO-IV norms with manifold injection. Countries like India with fewer natural fossil fuel reserves depend heavily on oil imported from Middle East Asian countries and on the other hand combustion of fossil fuel has negative impact on air quality in urban areas. Use of CNG as a fuel in internal combustion engines can reduce the intensiveness of these pervasive problems. The performance of CNG can further be improved by addition of small percentages of hydrogen to it to overcome the drawbacks like lower energy density of the fuel, drop in engine power and engine out exhaust emissions. When hydrogen is added to CNG it is called as Hythane or Hydrogen enriched Compressed Natural Gas (HCNG. This can be considered as a first step towards promotion of hydrogen in automobiles. In this study, the effects of mixing hydrogen with CNG on a small air cooled four stroke SI engine’s performance, emissions and heat release rate was analyzed. A comparison of performance and emission by running engine separately on gasoline, hydrogen, CNG and HCNG was done. The results show a significant decrease in HC, CO and NOx emissions and marginal increase in specific energy consumption when fuelled with HCNG.

  1. 3-DIMENSIONAL Numerical Modeling on the Combustion and Emission Characteristics of Biodiesel in Diesel Engines

    Science.gov (United States)

    Yang, Wenming; An, Hui; Amin, Maghbouli; Li, Jing

    2014-11-01

    A 3-dimensional computational fluid dynamics modeling is conducted on a direct injection diesel engine fueled by biodiesel using multi-dimensional software KIVA4 coupled with CHEMKIN. To accurately predict the oxidation of saturated and unsaturated agents of the biodiesel fuel, a multicomponent advanced combustion model consisting of 69 species and 204 reactions combined with detailed oxidation pathways of methyl decenoate (C11H22O2), methyl-9-decenoate (C11H20O2) and n-heptane (C7H16) is employed in this work. In order to better represent the real fuel properties, the detailed chemical and thermo-physical properties of biodiesel such as vapor pressure, latent heat of vaporization, liquid viscosity and surface tension were calculated and compiled into the KIVA4 fuel library. The nitrogen monoxide (NO) and carbon monoxide (CO) formation mechanisms were also embedded. After validating the numerical simulation model by comparing the in-cylinder pressure and heat release rate curves with experimental results, further studies have been carried out to investigate the effect of combustion chamber design on flow field, subsequently on the combustion process and performance of diesel engine fueled by biodiesel. Research has also been done to investigate the impact of fuel injector location on the performance and emissions formation of diesel engine.

  2. The laboratory test rig with miniature jet engine to research aviation fuels combustion process

    Directory of Open Access Journals (Sweden)

    Gawron Bartosz

    2015-12-01

    Full Text Available This article presents laboratory test rig with a miniature turbojet engine (MiniJETRig – Miniature Jet Engine Test Rig, that was built in the Air Force Institute of Technology. The test rig has been developed for research and development works aimed at modelling and investigating processes and phenomena occurring in full scale jet engines. In the article construction of a test rig is described, with a brief discussion on the functionality of each of its main components. Additionally examples of measurement results obtained during the realization of the initial tests have been included, presenting the capabilities of the test rig.

  3. Experimental combustion analysis of a hsdi diesel engine fuelled with palm oil biodiesel-diesel fuel blends

    OpenAIRE

    JOHN AGUDELO; ELKIN GUTIÉRREZ; PEDRO BENJUMEA

    2010-01-01

    Differences in the chemical nature between petroleum diesel fuels and vegetable oils-based fuels lead to differences in their physical properties affecting the combustion process inside the engine. In this work a detailed combustion diagnosis was applied to a turbocharged automotive diesel engine operating with neat palm oil biodiesel (POB), No. 2 diesel fuel and their blends at 20 and 50% POB by volume (B20 and B50 respectively). To isolate the fuel effect, tests were executed at constant po...

  4. Reduction gear for a turbo compound drive of a supercharged internal combustion engine. Reduktionsgetriebe fuer einen Turbocompoundantrieb einer aufgeladenen Brennkraftmaschine

    Energy Technology Data Exchange (ETDEWEB)

    Bergmann, H.; Fischer, G.; Bueschel, W.

    1991-01-24

    The invention concerns a reduction gear within the turbocompound drive of a supercharged internal combustion engine with at least two reduction stages and a one-way clutch. In order to decouple the vibrations of the turbine and the power plant of the internal combustion engine at least one torsion bushing is provided as which acts as a vibration damper. The one-way clutch is located in the hub of the drive of the second reduction stage in order to save space.

  5. Numerical analysis of hydrogen and methane propagation during testing of combustion engines

    Directory of Open Access Journals (Sweden)

    Dvořák V.

    2007-10-01

    Full Text Available The research of gas-fuelled combustion engines using hydrogen or methane require accordingly equipped test benches which take respect to the higher dangerous of self ignition accidents. This article deals with numerical calculations of flow in laboratory during simulated leakage of gas-fuel from fuel system of tested engine. The influences of local suction and influences of roof exhausters on the flow in the laboratory and on the gas propagation are discussed. Results obtained for hydrogen and for methane are compared. Conclusions for design and performance of suction devices and test benches are deduced from these results.

  6. Improvement on Performances of Internal Combustion Engine Using the Technology of Ceramic Coating

    Institute of Scientific and Technical Information of China (English)

    林建生; 付晓光; 张建昭

    2003-01-01

    This paper introduces a new technology of using ceramic coating on piston rings of an internal combustion engine, and the comparison of mechanical efficiency and performances of an actual engine before and after the application of ceramic coating on the piston rings. The experimental results show that the mechanical efficiency and power output are enhanced by 4% and 2.6%, respectively, with fuel consumption reduced by 2.9%. Further studies on coating processing and coating materials as well as the reliability and durability will be of great significance in the application and popularization of the new technology.

  7. Numerical Study on the Performance Characteristics of Hydrogen Fueled Port Injection Internal Combustion Engine

    Directory of Open Access Journals (Sweden)

    Rosli A. Bakar

    2009-01-01

    Full Text Available This study was focused on the engine performance of single cylinder hydrogen fueled port injection internal combustion engine. GT-Power was utilized to develop the model for port injection engine. One dimensional gas dynamics was represented the flow and heat transfer in the components of the engine model. The governing equations were introduced first, followed by the performance parameters and model description. Air-fuel ratio was varied from stoichiometric limit to a lean limit and the rotational speed varied from 2500 to 4500 rpm while the injector location was considered fixed in the midway of the intake port. The effects of air fuel ratio, crank angle and engine speed are presented in this study. From the acquired results show that the air-fuel ratio and engine speed were greatly influence on the performance of hydrogen fueled engine. It was shown that decreases the Brake Mean Effective Pressure (BMEP and brake thermal efficiency with increases of the engine speed and air-fuel ratio however the increase the Brake Specific Fuel Consumption (BSFC with increases the speed and air-fuel ratio. The cylinder temperature increases with increases of engine speed however temperature decreases with increases of air-fuel ratio. The pressure fluctuations increased substantially with increases of speed at intake port however rise of pressure at the end of the exhaust stroke lead to reverse flow into the cylinder past exhaust valve. The fluctuation amplitude responded to the engine speed in case of exhaust pressure were given less than the intake pressure. The volumetric efficiency increased with increases of engine speed and equivalent ratio. The volumetric efficiency of the hydrogen engines with port injection is a serious problem and reduces the overall performance of the engine. This emphasized the ability of retrofitting the traditional engines with hydrogen fuel with minor modifications.

  8. Impact of the injection dose of exhaust gases, on work parameters of combustion engine

    Science.gov (United States)

    Marek, W.; Śliwiński, K.

    2016-09-01

    This article is another one from the series in which were presented research results indicated the possible areas of application of the pneumatic injection using hot combustion gases proposed by Professor Jarnuszkiewicz. This publication present the results of the control system of exhaust gas recirculation. The main aim of this research was to determine the effect of exhaust gas recirculation to the operating parameters of the internal combustion engine on the basis of laboratory measurements. All measurements were performed at a constant engine speed. These conditions correspond to the operation of the motor operating an electrical generator. The study was conducted on the four-stroke two-cylinder engine with spark ignition. The study were specifically tested on the air injection system and therefore the selection of the rotational speed was not bound, as in conventional versions of operating parameters of the electrical machine. During the measurement there were applied criterion which used power control corresponding to the requirements of load power, at minimal values of engine speed. Recirculation value determined by the following recurrent position control valve of the injection doses inflator gas for pneumatic injection system. They were studied and recorded, the impact of dose of gases recirculation to the operating and ecological engine parameters such as power, torque, specific fuel consumption, efficiency, air fuel ratio, exhaust gas temperature and nitrogen oxides and hydrocarbons.

  9. Influence of the cooling degree upon performances of internal combustion engine

    Science.gov (United States)

    Grǎdinariu, Andrei Cristian; Mihai, Ioan

    2016-12-01

    Up to present, air cooling systems still raise several unsolved problems due to conditions imposed by the environment in terms of temperature and pollution levels. The present paper investigates the impact of the engine cooling degree upon its performances, as important specific power is desired for as low as possible fuel consumption. A technical solution advanced by the authors[1], consists of constructing a bi-flux compressor, which can enhance the engine's performances. The bi-flux axial compressor accomplishes two major functions, that is it cools down the engine and it also turbocharges it. The present paper investigates the temperature changes corresponding to the fresh load, during the use of a bi-flux axial compressor. This compressor is economically simple, compact, and offers an optimal response at low rotational speeds of the engine, when two compression steps are used. The influence of the relative coefficient of air temperature drop upon working agent temperature at the intercooler exit is also investigated in the present work. The variation of the thermal load coefficient by report to the working agent temperature is also investigated during engine cooling. The variation of the average combustion temperature is analyzed in correlation to the thermal load coefficient and the temperatures of the working fluid at its exit from the cooling system. An exergetic analysis was conducted upon the influence of the cooling degree on the motor fluid and the gases resulted from the combustion process.

  10. Automotive Thermoelectric Generator impact on the efficiency of a drive system with a combustion engine

    Directory of Open Access Journals (Sweden)

    Ziolkowski Andrzej

    2017-01-01

    Full Text Available Increasing the combustion engine drive systems efficiency is currently being achieved by structural changes in internal combustion engines and its equipment, which are geared towards limiting mechanical, thermal and outlet losses. For this reason, downsizing. In addition to these changes, all manner of exhaust gas energy recovery systems are being investigated and implemented, including turbocompound, turbogenerators and thermoelectric generators. The article presents the author’s idea of a thermoelectric generator system of automotive applications ATEG (Automotive Thermoelectric Generator and the study of the recovery of exhaust gas energy stream. The ATEG consists of a heat exchanger, thermoelectric modules and a cooling system. In this solution, 24 commercial thermoelectric modules based on Bi2Te3 (bismuth telluride were used. Measurements were made at two engine test sites on which SI and CI engines were installed. The exhaust gas parameters (temperature and mass flow rate, fuel consumption and operating parameters of the ATEG – the intensity and the voltage generated by the thermoelectric modules and the temperature on the walls of the heat exchanger – were all measured in the experiments. Based on the obtained results, the exhaust gas energy flow and the power of the ATEG were determined as well as its effect on the diesel engine drive system efficiency.

  11. A comprehensive study on waste heat recovery from internal combustion engines using organic Rankine cycle

    Directory of Open Access Journals (Sweden)

    Tahani Mojtaba

    2013-01-01

    Full Text Available There are a substantial amount of waste heat through exhaust gas and coolant of an Internal Combustion Engine. Organic Rankine cycle is one of the opportunities in Internal Combustion Engines waste heat recovery. In this study, two different configurations of Organic Rankine cycle with the capability of simultaneous waste heat recovery from exhaust gas and coolant of a 12L diesel engine were introduced: Preheat configuration and Two-stage. First, a parametric optimization process was performed for both configurations considering R-134a, R-123, and R-245fa as the cycle working fluids. The main objective in optimization process was maximization of the power generation and cycle thermal efficiency. Expander inlet pressure and preheating temperature were selected as design parameters. Finally, parameters like hybrid generated power and reduction of fuel consumption were studied for both configurations in different engine speeds and full engine load. It was observed that using R-123 as the working fluid, the best performance in both configurations was obtained and as a result the 11.73% and 13.56% reduction in fuel consumption for both preheat and Two-stage configurations were found respectively.

  12. Emission estimation of neat paradise tree oil combustion assisted with superheated hydrogen in a 4-stroke natural aspirated DICI engine

    Directory of Open Access Journals (Sweden)

    Sundararajan Karthikayan

    2016-01-01

    Full Text Available This research work investigates the use of neat paradise tree oil in a 4-stroke natural aspirated direct injection compression ignition engine assisted with the help of super-heated hydrogen (hydrogen in gaseous state or above its saturation temperature as a combustion improver. The high calorific gaseous fuel hydrogen gas was used as a combustion improver and admitted into the engine during the suction stroke. A 4-stroke single cylinder Diesel engine was chosen and its operating parameters were suitably modified. Neat paradise tree oil was admitted through standard injector of the engine and hydrogen was admitted through induction manifold. Inducted super-heated hydrogen was initiated the intermediate compounds combustion of neat paradise tree oil. This process offers higher temperature combustion and results in complete combustion of heavier molecules of neat paradise tree oil within shorter duration. The results of the experiment reveal that 40% higher NOx, 20% lower smoke, 5% lower CO, and 45% lower HC than that of neat paradise tree oil fuel operation and the admission of superheated hydrogen has improved the combustion characteristics of neat paradise tree oil. The investigation successfully proved that the application of neat paradise tree oil with 15% of hydrogen improver is possible under a regular Diesel engine with minimal engine modification.

  13. An Experimental Study of Emission and Combustion Characteristics of Marine Diesel Engine with Fuel Injector Malfunctions

    Directory of Open Access Journals (Sweden)

    Kowalski Jerzy

    2016-01-01

    Full Text Available The presented paper shows the results of the laboratory study on the relation between chosen malfunctions of a fuel injector and composition of exhaust gas from the marine engine. The object of research is a marine 3-cylinder, four-stroke, direct injection diesel engine with an intercooler system. The engine was loaded with a generator and supercharged. The generator was electrically connected to the water resistance. The engine operated with a load between 50 kW and 250 kW at a constant speed. The engine load and speed, parameters of the turbocharger, systems of cooling, fuelling, lubricating and air exchange, were measured. Fuel injection and combustion pressures in all cylinders of the engine were also recorded. Exhaust gas composition was recorded by using a electrochemical gas analyzer. Air pressure, temperature and humidity were also recorded. Emission characteristics of the engine were calculated according to ISO 8178 standard regulations. During the study the engine operated at the technical condition recognized as „working properly” and with simulated fuel injector malfunctions. Simulation of malfunctions consisted in the increasing and decreasing of fuel injector static opening pressure, decalibration of fuel injector holes and clogging 2 neighboring of 9 fuel injector holes on one of 3 engine cylinders.

  14. Maximizing Power Output in Homogeneous Charge Compression Ignition (HCCI) Engines and Enabling Effective Control of Combustion Timing

    Science.gov (United States)

    Saxena, Samveg

    Homogeneous Charge Compression Ignition (HCCI) engines are one of the most promising engine technologies for the future of energy conversion from clean, efficient combustion. HCCI engines allow high efficiency and lower CO2 emission through the use of high compression ratios and the removal of intake throttle valves (like Diesel), and allow very low levels of urban pollutants like nitric oxide and soot (like Otto). These engines, however, are not without their challenges, such as low power density compared with other engine technologies, and a difficulty in controlling combustion timing. This dissertation first addresses the power output limits. The particular strategies for enabling high power output investigated in this dissertation focus on avoiding five critical limits that either damage an engine, drastically reduce efficiency, or drastically increase emissions: (1) ringing limits, (2) peak in-cylinder pressure limits, (3) misfire limits, (4) low intake temperature limits, and (5) excessive emissions limits. The research shows that the key factors that enable high power output, sufficient for passenger vehicles, while simultaneously avoiding the five limits defined above are the use of: (1) high intake air pressures allowing improved power output, (2) highly delayed combustion timing to avoid ringing limits, and (3) using the highest possible equivalence ratio before encountering ringing limits. These results are revealed by conducting extensive experiments spanning a wide range of operating conditions on a multi-cylinder HCCI engine. Second, this dissertation discusses strategies for effectively sensing combustion characteristics on a HCCI engine. For effective feedback control of HCCI combustion timing, a sensor is required to quantify when combustion occurs. Many laboratory engines use in-cylinder pressure sensors but these sensors are currently prohibitively expensive for wide-scale commercialization. Instead, ion sensors made from inexpensive sparkplugs

  15. Development of combustion management concept for natural-aspirated small diesel engine; Shizen kyuki kogata diesel engine no nensho seigyo concept no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Wada, T.; Kawano, T.; Shoji, M.; Kuniyosh, M.; Yamashita, O.; Nagao, A. [Mazda Motor Corp., Tokyo (Japan); Yoshikawa, S. [Zexel Corp., Tokyo (Japan)

    1997-10-01

    We have developed a combustion management concept for natural-aspirated small IDI diesel engines and achieved higher power, lower exhaust emissions and more comfort. The concept is related to improvements of intake volumetric efficiency, EGR effect, mixture formation caused by combustion chamber and spray characteristics, engine management system and after treatment device. This paper describes the concept and experimental results. 3 refs., 14 figs., 1 tab.

  16. The problems of piston skirt microgeometry in combustion engines

    Science.gov (United States)

    Iskra, A.; Babiak, M.; Wróblewski, E.

    2016-09-01

    Geometry of the slot between piston bearing surface and cylinder bore affects the friction losses of the IC engine to the far extent. It appears that these losses depend more on the area covered with oil than the thickness of oil layer separating collaborating parts. Barrel-shaped or stepwise piston bearing surface is the way to reduce the oil covered area. Turns out that the referred to friction losses contributes more to area covered by the oil film than the film thickness of the separation elements cooperating. The method to reduce the area covered by the oil film is a modification of the bearing surface of the piston by adjusting the profile. This paper presents the results of simulation leading to the reduction in friction losses and abrasive wear of piston bearing surface and cylinder bore. Covering the piston bearing surface with a thin layer of graphite one can get an extremely advantageous tribological properties of the piston assembly which means the expected parameters of oil film and in a case of film rupture-an ignorable abrasive wear of the graphite layer and/or cylinder bore.

  17. Oxides of nitrogen measurement at exhaust gases of combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Prietsch, W.; Alter, C.; Naumann, M.

    1975-01-01

    Chemical and physical methods available for the determination of nitrogen oxides were tested and compared with respect to their suitability for spark-ignition and diesel engine exhaust oxides of nitrogen analysis. Of all methods tested (Saltzmans method, phenoldisulfonic acid method, as well as non-dispersive infrared, ultraviolet absorption, and chemiluminescence methods), the chemiluminescence method was best for the determination of the total nitrogen oxides concentration in vehicle exhaust, even though the nitrogen dioxide conversion is still problematic, and the NO/sub 2/ concentrations lie within the dispersion limits of the nitric oxide analyzer. Measurement of NO is possible by the NDIR method provided the cross-sensitivity for water is simultaneously measured, and adequate correction is used. The Saltzman method is preferable to the phenoldisulfonic acid method under stationary analytical conditions due to its simplicity and reliability. For a concentration range of 100 to 1000 ppM, a Saltzman factor of 0.72 is best for exhaust nitrogen oxides analysis.

  18. Combustion Control System Design of Diesel Engine via ASPR based Output Feedback Control Strategy with a PFC

    Science.gov (United States)

    Mizumoto, Ikuro; Tsunematsu, Junpei; Fujii, Seiya

    2016-09-01

    In this paper, a design method of an output feedback control system with a simple feedforward input for a combustion model of diesel engine will be proposed based on the almost strictly positive real-ness (ASPR-ness) of the controlled system for a combustion control of diesel engines. A parallel feedforward compensator (PFC) design scheme which renders the resulting augmented controlled system ASPR will also be proposed in order to design a stable output feedback control system for the considered combustion model. The effectiveness of our proposed method will be confirmed through numerical simulations.

  19. Numerical simulation of charge stratifications to improve combustion and NO formation of lean-burn SI engines

    Institute of Scientific and Technical Information of China (English)

    Zhijun PENG

    2009-01-01

    The influences of charge stratification on spark ignition (SI) engine combustion and NO emission were analyzed using a phenomenological model. The mixture in the cylinder was divided spherically into three parts: a central core with a stoichiometric air-fuel charge, a dilution region without any combustible charge, and a mixing region lying between the core and the dilution region.Three mixture stratification parameters such as the extent of dilution in the mixing region, the extent of combustible charge in the mixing region, and the gradient of stratification in the mixing region were investigated. The results indicate that the extent of combustible charge in the mixing region could reduce in-cylinder NO formation significantly, compared with the extent of dilution in the mixing region. As long as the degree of dilution in the mixing region is within the dilution limit of the combustible charge, the gradient of dilution has little effect on combustion and NO formation.

  20. High Thermal Conductivity NARloy-Z-Diamond Composite Combustion Chamber Liner For Advanced Rocket Engines

    Science.gov (United States)

    Bhat, Biliyar N.; Ellis, David; Singh, Jogender

    2014-01-01

    Advanced high thermal conductivity materials research conducted at NASA Marshall Space Flight Center (MSFC) with state of the art combustion chamber liner material NARloy-Z showed that its thermal conductivity can be increased significantly by adding diamond particles and sintering it at high temperatures. For instance, NARloy-Z containing 40 vol. percent diamond particles, sintered at 975C to full density by using the Field assisted Sintering Technology (FAST) showed 69 percent higher thermal conductivity than baseline NARloy-Z. Furthermore, NARloy-Z-40vol. percent D is 30 percent lighter than NARloy-Z and hence the density normalized thermal conductivity is 140 percent better. These attributes will improve the performance and life of the advanced rocket engines significantly. By one estimate, increased thermal conductivity will directly translate into increased turbopump power up to 2X and increased chamber pressure for improved thrust and ISP, resulting in an expected 20 percent improvement in engine performance. Follow on research is now being conducted to demonstrate the benefits of this high thermal conductivity NARloy-Z-D composite for combustion chamber liner applications in advanced rocket engines. The work consists of a) Optimizing the chemistry and heat treatment for NARloy-Z-D composite, b) Developing design properties (thermal and mechanical) for the optimized NARloy-Z-D, c) Fabrication of net shape subscale combustion chamber liner, and d) Hot fire testing of the liner for performance. FAST is used for consolidating and sintering NARlo-Z-D. The subscale cylindrical liner with built in channels for coolant flow is also fabricated near net shape using the FAST process. The liner will be assembled into a test rig and hot fire tested in the MSFC test facility to determine performance. This paper describes the development of this novel high thermal conductivity NARloy-Z-D composite material, and the advanced net shape technology to fabricate the combustion

  1. Control of homogeneous charge compression ignition combustion in a two-cylinder gasoline direct injection engine with negative valve overlap

    Institute of Scientific and Technical Information of China (English)

    WANG Zhi; WANG Jianxin; SHUAI Shijin; MA Qingjun; TIAN Guohong

    2007-01-01

    Homogeneous charge compression ignition(HCCI) has challenges in ignition timing control,combustion rate control,and operating range extension.In this paper,HCCI combustion was studied in a two-cylinder gasoline direct injection (GDI) engine with negative valve overlap (NVO).A two-stage gasoline direct injection strategy combined with negative valve overlap was used to control mixture formation and combustion.The gasoline engine could be operated in HCCI combustion mode at a speed range of 800-2 200 r/min and load,indicated mean effective pressure (IMEP) range of 0.1-0.53 MPa.The engine fuel consumption 4× 10-5 without soot emission.The effect of different injection strategies on HCCI combustion was studied.The experimental results indicated that the coefficient of variation of the engine cycle decreased by using NVO with two-stage direct injection;the ignition timing and combustion rate could be controlled;and the operational range of HCCI combustion could be extended.

  2. US-Japan Seminar on Modeling in Combustion Science

    CERN Document Server

    Takeno, Tadao

    1995-01-01

    The articles in this volume treat various problems in combustion science that are of importance in applications to technology and to environmental sciences. The authors treat turbulence in premixed and non-premixed flames as well as pressure interactions and wave phenomena. Also supersonic flows and detonations are discussed. The main emphasis, however, is on the modelling and numerical treatment of combustion phenomena. The book addresses researchers in physics and engineering, and mathematicians from scientific computing.

  3. Experimental investigation of gasoline compression ignition combustion in a light-duty diesel engine

    Science.gov (United States)

    Loeper, C. Paul

    Due to increased ignition delay and volatility, low temperature combustion (LTC) research utilizing gasoline fuel has experienced recent interest [1-3]. These characteristics improve air-fuel mixing prior to ignition allowing for reduced emissions of nitrogen oxides (NOx) and soot (or particulate matter, PM). Computational fluid dynamics (CFD) results at the University of Wisconsin-Madison's Engine Research Center (Ra et al. [4, 5]) have validated these attributes and established baseline operating parameters for a gasoline compression ignition (GCI) concept in a light-duty diesel engine over a large load range (3-16 bar net IMEP). In addition to validating these computational results, subsequent experiments at the Engine Research Center utilizing a single cylinder research engine based on a GM 1.9-liter diesel engine have progressed fundamental understanding of gasoline autoignition processes, and established the capability of critical controlling input parameters to better control GCI operation. The focus of this thesis can be divided into three segments: 1) establishment of operating requirements in the low-load operating limit, including operation sensitivities with respect to inlet temperature, and the capabilities of injection strategy to minimize NOx emissions while maintaining good cycle-to-cycle combustion stability; 2) development of novel three-injection strategies to extend the high load limit; and 3) having developed fundamental understanding of gasoline autoignition kinetics, and how changes in physical processes (e.g. engine speed effects, inlet pressure variation, and air-fuel mixture processes) affects operation, develop operating strategies to maintain robust engine operation. Collectively, experimental results have demonstrated the ability of GCI strategies to operate over a large load-speed range (3 bar to 17.8 bar net IMEP and 1300-2500 RPM, respectively) with low emissions (NOx and PM less than 1 g/kg-FI and 0.2 g/kg-FI, respectively), and low

  4. Combustion oscillation study in a kerosene fueled rocket-based combined-cycle engine combustor

    Science.gov (United States)

    Huang, Zhi-Wei; He, Guo-Qiang; Qin, Fei; Xue, Rui; Wei, Xiang-Geng; Shi, Lei

    2016-12-01

    This study reports the combustion oscillation features in a three-dimensional (3D) rocket-based combined-cycle (RBCC) engine combustor under flight Mach number (Mflight) 3.0 conditions both experimentally and numerically. Experiment is performed on a direct-connect ground test facility, which measures the wall pressure along the flow-path. High-speed imaging of the flame luminosity and schlieren is carried out at exit of the primary rocket. Compressible reactive large eddy simulation (LES) with reduced chemical kinetics of a surrogate model for kerosene is performed to further understand the combustion oscillation mechanisms in the combustor. LES results are validated with experimental data by the time-averaged and root mean square (RMS) pressure values, and show acceptable agreement. Effects of the primary rocket jet on pressure oscillation in the combustor are analyzed. Relation of the high speed rocket jet oscillation, which is thought to among the most probable sources of combustion oscillation, with the RBCC combustor is recognized. Results reveal that the unsteady over-expanded rocket jet has significant impacts on the combustion oscillation feature of the RBCC combustor, which is different from a thermo-acoustics type oscillation. The rocket jet/air inflow physical interactions under different rocket jet expansion degrees are experimentally studied.

  5. Autoignition and Combustion of Natural Gas in a 4 Stroke HCCI Engine

    Science.gov (United States)

    Jun, Daesu; Ishii, Kazuaki; Iida, Norimasa

    Homogeneous charge compression ignition (HCCI) is regarded as the next generation combustion regime in terms of high thermal efficiency and low emissions. It is difficult to control autoignition timing and combustion duration because they are controlled primarily by the chemical kinetics of fuel-air mixture. In this study, it was investigated the characteristics of autoignition and combustion of natural gas in a 4 stroke HCCI engine. And also, to clarify the influence of n-butane on autoignition and combustion of natural gas, it was changed the blend ratio of n-butane from 0mol% to 10mol% in methane/n-butane/air mixtures. Autoignition strongly depends on in-cylinder gas temperature. Autoignition of natural gas occurs when in-cylinder gas temperature reaches in a range of 1000±100K under this experimental condition. To realize high thermal efficiency and low CO emissions, it is necessary to prepare operation conditions that maximum cycle temperature is over 1500K. Autoignition temperature is 25K lower by increasing n-butane blend ratio of 10%. As the blend ratio of n-butane increases, the maximum cycle temperature increases, and THC, CO emissions reduce.

  6. Lean-Burn Cogeneration Biogas Engine with Unscavenged Combustion Prechamber: Comparison with Natural Gas

    Directory of Open Access Journals (Sweden)

    Roger Röthlisberger

    2002-12-01

    Full Text Available Gaseous fuels produced, for example, by waste or agricultural by-products fermentation (biogas can be burned in-situ by cogeneration systems like spark-ignition internal combustion engines. However, the more and more stringent legislation for exhaust gas emissions requires improvement of the combustion process particularly when catalytic after treatment is not reliable as in the case of sewage or landfill biogas. The system proposed in this paper is the use of an unscavenged combustion prechamber instead of direct ignition on a turbocharged 6 cylinder 150 kW gas engine. This prechamber is used for operation with a simulated biogas (40% CO2 in natural gas. The results show that, compared to natural gas operation for the same rated power output of 150 kW and the same NOx emissions, the CO emissions are reduced by 15% and the HC emissions at least by 8%. Efficiencies higher than 36% are achieved which is very promising and the lower CO emissions give a margin to consider an increase of compression ratio.

  7. Combustion Analysis of a Diesel Engine Running on Different Biodiesel Blends

    Directory of Open Access Journals (Sweden)

    Enrico Mattarelli

    2015-04-01

    Full Text Available Rape-seed biodiesel is an interesting option to address the problem of decreasing availability of conventional fossil fuels, as well as to reduce the CO2 emissions of internal combustion engines. The present paper describes an experimental campaign carried out on a current production 4-cylinder, 4-stroke naturally aspirated diesel engine, running on standard diesel fuel and on three different blends of rape-seed biodiesel (20%-50%-100%. Performance, emissions and in-cylinder pressure traces were measured at full load. It was found that the influence of rape-seed biodiesel in the fuel blend is not constant at each operating condition. However, as the biodiesel content increases, full load performance tends to drop, in particular brake specific fuel consumption (maximum worsening: +18%, while soot emission goes down. The maximum improvement observed in terms of soot concentration is 37.5%, at 1200 rpm. The combustion analysis revealed that the main differences among the fuels occur in the first phase of combustion: the burn rate is slower for biodiesel blends at low speeds, and faster at high.

  8. Resonance vibrations of cylinder charge of Diesel engines and their importance for combustion noise. Resonanzschwingungen der Zylinderladung von Dieselmotoren und ihre Bedeutung fuer das Verbrennungsgeraeusch

    Energy Technology Data Exchange (ETDEWEB)

    Schneider, M.H.

    1987-09-10

    Measurements of the pressure distribution in the gas charge of the combustion space were made on Diesel engines, in a combustion chamber and on a test rig. They describe the significance of inherent resonance vibrations of the gas charge for Diesel engine combustion and for engine acoustics. There are reports on the known principal conditions (inherent vibration pressure amplitude, degree of excitation, combination of several part combustion chambers, wavelengths, phase position) and on the digital analysis (computer-aided) of combustion space inherent vibrations. Data are given on part components of engine noise, possible excitation by pressure variations in the cylinder charge, the theory of combustion space resonance vibration, the conversion of gas pressure variations into combustion noise and investigations on the running engine. (HWJ).

  9. Study on the Combustion Process and Emissions of a Turbocharged Diesel Engine with EGR

    Directory of Open Access Journals (Sweden)

    Mei Deqing

    2012-01-01

    Full Text Available A high pressure EGR system was adopted to a turbocharged inter-cooled diesel engine, to analyze its combustion and emission characteristics under the condition of different loads and constant speed. Under the same steady operating mode, with the increase of EGR rate, the temperature of compressed gas ascended, the ignition delay was shortened, the pressure and temperature of the burned gas descended, and the combustion process was prolonged. According to the experimental data, it was found that, at the same EGR rate, lower the load of engine was, lower the temperature in cylinder, and higher the increase rate of CO was. However, the increase rate of HC present a falling trend. The decrease rate of the specific emission of NOx linearly varied with EGR rate with a slope of 1.651. The increase rate of smoke opacity behaved a second-order polynomial uprising trend, and the higher the load was, the sharpener the smoke opacity deteriorated, with the increase of EGR rate. From the point of emission view, the engine with EGR system can achieve the lesser exhaust emissions in some operations by adjusting the engine parameters.

  10. Evaluation of direct combustion chamber information in internal combustion engines using methods of estimation theory; Auswertung direkter Brennrauminformationen am Verbrennungsmotor mit estimationstheoretischen Methoden

    Energy Technology Data Exchange (ETDEWEB)

    Hart, M.

    1999-04-16

    The estimation of the air mass in the cylinder of a spark ignition (SI) engine is crucial in order to regulate the exact air fuel (A/F) ratio for the catalyst and thus minimize the emissions. Conventional algorithms for estimating the air mass are based on sensor information measured in front of the throttle or in the manifold. Thus, the determination of cylinder individual sizes, particularly the air mass, is impossible. In this work, new sensors, which provide cylinder individual information are investigated and the air mass in each individual cylinder is calculated with adaptive, model based algorithms. Sensors within the combustion chamber of an SI engine enable a cylinder specific evaluation of the thermodynamic work process. In particular, the combustion pressure sensor or ionisation current sensing are two independent methods of measuring direct combustion information. In a few cases such sensors are used in mass production cars. The combustion pressure sensor exhibits two significant advantages when compared to ionisation current. First, it provides information of the pressure in the cylinder during the complete working cycle of the engine and this pressure information is a measure of the entire combustion chamber. In contrast, the ionisation sensing represents a local measurement during the combustion and part of the expansion phase and this measurement can only be seen as a part of the information contained in the combustion pressure sensor signal. Second, the determination of the air mass in the cylinder, the most significant process information, can only be determined by cylinder pressure measurements and not by ionisation current. Reducing costs by eliminating the mass air flow meter is a requirement for the implementation of combustion pressure sensors in a mass production throttled SI engine. Thus, the cylinder pressure sensor must be able to determine the air mass in the cylinder. However, the cylinder pressure sensors will not be implemented in a

  11. Modeling of heat release and emissions from droplet combustion of multi component fuels in compression ignition engines

    OpenAIRE

    Ivarsson, Anders; Schramm, Jesper

    2010-01-01

    This PhD dissertation was carried out at the Technical University of Denmark in Department of Mechanical Engineering and supervised by Associate Professor Jesper Schramm. The PhD project was funded by the Technical University of Denmark. Demands on reducing the fuel consumption and harmful emissions from the compression ignition engines (CI engines or diesel engines) are continuously increased. To comply with this, better modeling tools for the diesel combustion process are desired from the e...

  12. Numerical simulation of fuel sprays and combustion in a premixed lean diesel engine; Kihaku yokongo diesel kikan ni okeru nenryo funmu to nensho no suchi simulation

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, T.; Harada, A.; Sasaki, S.; Shimazaki, N.; Hashizume, T.; Akagawa, H.; Tsujimura, K.

    1997-10-01

    Fuel sprays and combustion in a direct injection Premixed lean Diesel Combustion (PREDIC) engine, which can make smokeless combustion with little NOx emission, is studied numerically. Numerical simulation was carried out by means of KIVA II based computer code with a combustion submodel. The combustion submodel describes the formation of combustible fuel vapor by turbulent mixing and four-step chemical reaction which includes low temperature oxidation. Comparison between computation and experiment shows qualitatively good agreement in terms of heat release rate and NO emission. Computational results indicate that the combustion is significantly influenced by fuel spray characteristics and injection timing to vary NO emission. 10 refs., 8 figs., 1 tab.

  13. Heat science and transport phenomena in fuel cells; Thermique et phenomenes de transport dans les piles a combustible

    Energy Technology Data Exchange (ETDEWEB)

    Liberatore, P.M.; Boillot, M. [Laboratoire des Sciences du Genie Chimique de Nancy, 54 - Vandoeuvre-les-Nancy (France); Bonnet, C.; Didieerjean, S.; Lapicque, F.; Deseure, J.; Lottin, O.; Maillet, D.; Oseen-Senda, J. [Laboratoire d' Energetique et de Mecanique Theorique et Appliquee, 54 - Vandoeuvre Les Nancy (France); Alexandre, A. [Laboratoire d' Etudes Thermiques, ENSMA, 86 Poitiers (France); Topin, F.; Occelli, R.; Daurelle, J.V. [IUSTI / Polytech' Marseille, Institut universitaire des Systemes Thermiques Industriels Ecole, 13 - Marseille (France); Pauchet, J.; Feidt, M. [CEA Grenoble, Groupement pour la recherche sur les echangeurs thermiques (Greth), 38 (France); Voarino, C. [CEA Centre d' Etudes du Ripault, 37 - Tours (France); Morel, B.; Laurentin, J.; Bultel, Y.; Lefebvre-Joud, F. [CEA Grenoble, LEPMI, 38 (France); Auvity, B.; Lasbet, Y.; Castelain, C.; Peerohossaini, H. [Ecole Centrale de Nantes, Laboratoire de Thermocinetique de Nantes (LTN), 44 - Nantes (France)

    2005-07-01

    In this work are gathered the transparencies of the lectures presented at the conference 'heat science and transport phenomena in fuel cells'. The different lectures have dealt with 1)the gas distribution in the bipolar plates of a fuel cell: experimental studies and computerized simulations 2)two-phase heat distributors in the PEMFC 3)a numerical study of the flow properties of the backing layers on the transfers in a PEMFC 4)modelling of the heat and mass transfers in a PEMFC 5)two-phase cooling of the PEMFC with pentane 6)stationary thermodynamic model of the SOFC in the GECOPAC system 7)modelling of the internal reforming at the anode of the SOFC 8)towards a new thermal design of the PEMFC bipolar plates. (O.M.)

  14. Enhanced combustion by jet ignition in a turbocharged cryogenic port fuel injected hydrogen engine

    Energy Technology Data Exchange (ETDEWEB)

    Boretti, Alberto A.; Watson, Harry C. [Department of Mechanical Engineering, The University of Melbourne, 3010 Melbourne (Australia)

    2009-03-15

    The Hydrogen Assisted Jet Ignition (HAJI) is a physico-chemical combustion enhancement system developed at the University of Melbourne. Jet ignition can ignite ultra-lean air/fuel mixtures which are far beyond the stable ignition limit of a spark plug. Jet ignition may further enhance the combustion properties of hydrogen enabling the development of a diesel-like, almost throttle-less, control of load by quantity of fuel injected for higher thermal efficiencies all over the range of loads. The object of this paper is to show the benefits of jet ignition and present the latest results obtained on a four cylinder engine having the jet ignition coupled with cryogenic hydrogen injection and turbo charging. (author)

  15. Blind source separation of internal combustion engine piston slap from other measured vibration signals

    Science.gov (United States)

    Liu, Xianhua; Randall, R. B.

    2005-11-01

    Internal combustion engines have several vibration sources, such as combustion, fuel injection, piston slap and valve operation. For machine condition monitoring or design improvement purposes, it is necessary to separate the vibration signals caused by different sources and then analyse each of them individually. However, traditional frequency analysis techniques are not very useful due to overlap of the different sources over a wide frequency range. This paper attempts to separate the vibration sources, especially piston slap, by using blind source separation techniques with the intention of revealing the potential of the new technique for solving mechanical vibration problems. The BSS method and the Blind least mean square algorithm using Gray's variable norm as a measure of non-Gaussianity of the sources is briefly described and separation results for both simulated and measured data are presented and discussed.

  16. Conversion of the exhaust emission results obtained from combustion engines of heavy-duty vehicles

    Science.gov (United States)

    Merkisz, J.; Pielecha, J.

    2016-09-01

    The use of internal combustion engines as the drive for heavy-duty vehicles forces these engines to be tested on an engine dynamometer. Thus, these engines operate under forced conditions, which are significantly different from their actual application. To assess the ecology of such vehicles (or more accurately the engine alone) the emission of pollution per unit of work done by the engine must be determined. However, obtaining the results of unit emissions (expressed in grams of the compound per a unit of performed work) does not give the grounds for determining the mass of pollutants on a given stretch of the road travelled by the vehicle. Therefore, there is a need to change the emission value expressed in units referenced to the engine work into a value of road emissions. The paper presents a methodology of determining pollutant emissions of heavy-duty road vehicles on the basis of the unit emissions, as well as additional parameters determined on the basis of the algorithm presented in the article. A solution was obtained that can be used not only for heavy-duty vehicles, but was also extended to allow use for buses.

  17. Performance and combustion characteristics of a direct injection SI hydrogen engine

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadi, Ali [Engine Technology, Powertrain, Toyota Motor Europe, Technical centre Hoge Wei 33 Zaventem 1930 (Belgium); Shioji, Masahiro; Nakai, Yasuyuki; Ishikura, Wataru [Graduate School of Energy Science, Kyoto University, Yoshida-honmachi Sakyo-ku Kyoto 605-8501 (Japan); Tabo, Eizo [Environmental and Technical Affairs Department, Mitsubishi Motors Co., 5-33-8 Shiba Minatoku Tokyo 108-8401 (Japan)

    2007-02-15

    Hydrogen with low spark-energy requirement, wide flammability range and high burning velocity is an important candidate for being used as fuel in spark-ignition engines. It also offers CO{sub 2} and HC free combustion and lean operation resulting in lower NO{sub x} emissions. However, well examined external mixing of hydrogen with intake air causes backfire and knock especially at higher engine loads. In addition, low heating value per unit of volume of hydrogen limits the maximum output power. In this study, attention was paid to full usage of hydrogen advantage employing internal mixing method. Hydrogen was directly injected into cylinder of a single-cylinder test engine using a high-pressure gas injector and effects of injection timing and spark timing on engine performance and NO{sub x} emission were investigated under wide engine loads. The results indicate that direct injection of hydrogen prevents backfire, and that high thermal efficiency and output power can be achieved by hydrogen injection during late compression stroke. Moreover, by further optimization of the injection timing for each engine load, NO{sub x} emission can be reduced under the high engine output conditions. (author)

  18. Investigation of the effects of renewable diesel fuels on engine performance, combustion, and emissions

    KAUST Repository

    Ogunkoya, Dolanimi

    2015-01-01

    A study was undertaken to investigate renewable fuels in a compression-ignition internal combustion engine. The focus of this study was the effect of newly developed renewable fuels on engine performance, combustion, and emissions. Eight fuels were investigated, and they include diesel, jet fuel, a traditional biodiesel (fatty acid methyl ester: FAME), and five next generation biofuels. These five fuels were derived using a two-step process: hydrolysis of the oil into fatty acids (if necessary) and then a thermo-catalytic process to remove the oxygen via a decarboxylation reaction. The fuels included a fed batch deoxygenation of canola derived fatty acids (DCFA), a fed batch deoxygenation of canola derived fatty acids with varying amounts of H2 used during the deoxygenation process (DCFAH), a continuous deoxygenation of canola derived fatty acids (CDCFA), fed batch deoxygenation of lauric acid (DLA), and a third reaction to isomerize the products of the deoxygenated canola derived fatty acid alkanes (IPCF). Diesel, jet fuel, and biodiesel (FAME) have been used as benchmarks for comparing with the newer renewable fuels. The results of the experiments show slightly lower mechanical efficiency but better brake specific fuel consumption for the new renewable fuels. Results from combustion show shorter ignition delays for most of the renewable (deoxygenated) fuels with the exception of fed batch deoxygenation of lauric acid. Combustion results also show lower peak in-cylinder pressures, reduced rate of increase in cylinder pressure, and lower heat release rates for the renewable fuels. Emission results show an increase in hydrocarbon emissions for renewable deoxygenated fuels, but a general decrease in all other emissions including NOx, greenhouse gases, and soot. Results also demonstrate that isomers of the alkanes resulting from the deoxygenation of the canola derived fatty acids could be a potential replacement to conventional fossil diesel and biodiesel based on the

  19. Research of Data Acquisition and Analysis System for Internal Combustion Engine Based on DSP

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Y H [Center of Test Science of Jilin University, Chang chun, 130022 (China); Tian, X L [College of Instrumentation and Electrical Engineering of Jilin University, Jilin (China); Cheng, P [Center of Test Science of Jilin University, Chang chun, 130022 (China); Chang, X [College of Instrumentation and Electrical Engineering of Jilin University, Jilin (China); Dou, W J [College of Instrumentation and Electrical Engineering of Jilin University, Jilin (China)

    2006-10-15

    In the paper, the structure, working principle, functions and characteristics of an data acquisition and analysis system for internal combustion engines (I.C. engine) based on DSP is introduced. The DSP can not only acquire and analyze the data alone, also can work with the PC together to form data acquisition and analysis system with high speed and large memory. The system takes advantages of TMS320F2812's plenty of peripherals on chip, becomes small and easy for installation. USB technique is used to translate data between DSP and PC in high speed, so the system's real time processing is proved very much. It is proved that the designed system can acquire and analyze the steady and transient parameters of the I.C. engine very well.

  20. Performance and Emissions of Internal Combustion Engine Fuelled With CNG - A Review

    Directory of Open Access Journals (Sweden)

    P. M. Darade

    2012-10-01

    Full Text Available The development of alternative fuels such as natural gases has become very essential because of the continuously decrease in the petroleum reserves and also their contribution for pollutants. In this paper, a survey of research papers on the utilization of Compressed Natural Gas in the Internal Combustion engines along with its effects on the performance and emissions is done. It is revealed that the performance characteristics except thermal efficiency and exhaust temperature, various other performance parameters like brake mean effective pressure, power, torque and brake specific fuel consumption are decreased for CNG fuelled engine while the emission characteristics of unburnt hydrocarbon, Carbon monoxide and Carbon-di-oxide except nitrogen oxides are better for CNG compared to petrol and diesel engines. The improvement in performance is observed with the addition of hydrogen.

  1. Experimental Investigation of Active Noise Controller for Internal Combustion Engine Exhaust System

    Science.gov (United States)

    Wu, Jian-Da; Chen, Chih-Keng; Lee, Chun-Ying; Lee, Tian-Hua

    2002-10-01

    Two active noise control (ANC) algorithms for internal combustion engine exhaust systems are developed and their performances are compared in various experiments. The first controller is based on the filtered-x least mean square (FXLMS) algorithm with feedback neutralization, while the second is a fixed controller with a gain-scheduled active control technique for broadband attenuation with thermal effects. Both control algorithms are implemented on a digital signal processing (DSP) platform. Experiments are carried out to evaluate the attenuation performance of the proposed active noise control systems for an engine exhaust system. The results of the experiments indicate that both the adaptive controller and the gain-scheduled controller effectively suppress the noise of engine exhaust systems. The experimental comparison and analysis of the proposed controllers are also described.

  2. FAILURE MECHANISMS OF THERMAL BARRIER COATINGS INTERNAL COMBUSTION ENGINES AND llMPROVEMENTS

    Directory of Open Access Journals (Sweden)

    ADNAN PARLAK

    2003-04-01

    Full Text Available MechanicaJ properties of high performance ceramics have been improved to the point where their use in heat engines is possible. The high temperature strength and low thermal expansion properties of bigh performance ceramics offer an advantage over metals in the development of non-water cooling engine. However, because bard environment in diesel engine combustion chamber, solving the problem of durabiUty of TBC is important. DurabiUty of thermal barrier coatings(TBC is liınited by two main failure mechanisms: Therınal expansion nlİsmatch betwcen bond coat and top coat and bond coat oxidation. Both of these can cause failure of the ceramic top coat. Developments of recent years sholv that bond coats \\Vith higher oxidation resistance tend to have better coating system cyclic lives

  3. Experimental study of CH4/H2 mixtures-LPG-gasoline in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Bayrak, Mehmet; Albayrak Ceper, Bilge; Kahraman, Nafiz; Orhan Akansu, Selahaddin [Dept. of Mechanical Engineering, Erciyes University Engineering Faculty (Turkey)], e-mail: akansu@erciyes.edu.tr

    2011-07-01

    With the depletion of fossil fuel and the rising concerns about the environment, there is an urgent need for alternative fuels with low environmental impact. Research has been carried out world-wide to determine the energetic and environmental performance of alternative fuels in existing engines and the aim of this paper is to study the performance of engines using CH4/H2 (90% CH4 and 10% H2), liquefied petroleum gas (LPG) and gasoline. Experiments were conducted on a Kathana engine running at between 1500 and 3500 rotations per minutes and with spark timing between 10 and 35 BTDC. It was found that the CH4/H2 mix provides the lowest pollutant emission values of the studied fuels and the lowest brake thermal efficiency. This study provided a better understanding of the exhaust emission and combustion performances of CH4/H2 and LPG compared to gasoline.

  4. Preliminary results on performance testing of a turbocharged rotary combustion engine

    Science.gov (United States)

    Meng, P. R.; Rice, W. J.; Schock, H. J.; Pringle, D. P.

    1982-01-01

    The performance of a turbocharged rotary engine at power levels above 75 kW (100 hp) was studied. A twin rotor turbocharged Mazda engine was tested at speeds of 3000 to 6000 rpm and boost pressures to 7 psi. The NASA developed combustion diagnostic instrumentation was used to quantify indicated and pumping mean effect pressures, peak pressure, and face to face variability on a cycle by cycle basis. Results of this testing showed that a 5900 rpm a 36 percent increase in power was obtained by operating the engine in the turbocharged configuration. When operating with lean carburetor jets at 105 hp (78.3 kW) and 4000 rpm, a brake specific fuel consumption of 0.45 lbm/lb-hr was measured.

  5. DOE Project: Optimization of Advanced Diesel Engine Combustion Strategies "University Research in Advanced Combustion and Emissions Control" Office of FreedomCAR and Vehicle Technologies Program

    Energy Technology Data Exchange (ETDEWEB)

    Reitz, Rolf; Foster, D.; Ghandhi, J.; Rothamer, D.; Rutland, C.; Sanders, S.; Trujillo, M.

    2012-10-26

    The goal of the present technology development was to increase the efficiency of internal combustion engines while minimizing the energy penalty of meeting emissions regulations. This objective was achieved through experimentation and the development of advanced combustion regimes and emission control strategies, coupled with advanced petroleum and non-petroleum fuel formulations. To meet the goals of the project, it was necessary to improve the efficiency of expansion work extraction, and this required optimized combustion phasing and minimized in-cylinder heat transfer losses. To minimize fuel used for diesel particulate filter (DPF) regeneration, soot emissions were also minimized. Because of the complex nature of optimizing production engines for real-world variations in fuels, temperatures and pressures, the project applied high-fidelity computing and high-resolution engine experiments synergistically to create and apply advanced tools (i.e., fast, accurate predictive models) developed for low-emission, fuel-efficient engine designs. The companion experiments were conducted using representative single- and multi-cylinder automotive and truck diesel engines.

  6. Linkages from DOE’s Vehicle Technologies R&D in Advanced Combustion to More Efficient, Cleaner-Burning Engines

    Energy Technology Data Exchange (ETDEWEB)

    Ruegg, Rosalie [TIA Consulting Inc., Emerald Isle, NC (United States); Thomas, Patrick [1790 Analytics LLC., Haddonfield, NC (United States)

    2011-06-01

    This report uses bibliometric analysis, supported by interview and review of documents and databases, to trace linkages from knowledge outputs resulting from DOE's advances in vehicle engine combustion to downstream innovations in commercial diesel engines and other areas. This analysis covers the period from 1974 through 2008 (and in some cases to early 2009).

  7. A Study on the Effects of Compression Ratio, Engine Speed and Equivalence Ratio on HCCI Combustion of DME

    DEFF Research Database (Denmark)

    Pedersen, Troels Dyhr; Schramm, Jesper

    2007-01-01

    An experimental study has been carried out on the homogeneous charge compression ignition (HCCI) combustion of Dimethyl Ether (DME). The study was performed as a parameter variation of engine speed and compression ratio on excess air ratios of approximately 2.5, 3 and 4. The compression ratio...... was adjusted in steps to find suitable regions of operation, and the effect of engine speed was studied at 1000, 2000 and 3000 RPM. It was found that leaner excess air ratios require higher compression ratios to achieve satisfactory combustion. Engine speed also affects operation significantly....

  8. Floating-point coprocessor for fault detection and isolation in electronically controlled internal combustion engines. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Yu, T.L.; Ribbens, W.B.

    1991-09-01

    The report details the design of a floating-point coprocessor intended for real-time fault detection in electronically controlled internal combustion engines. The fault detection strategies are based on dynamic models of various engine subsystems and require the use of state estimators. The coprocessor can be operated at a clock rate of 24 MHz, and is capable of operating up to sixteen state estimators in real time. The design is suitable for application to internal combustion engines used for vehicle propulsion or power generation, whether diesel or spark ignited.

  9. A Study on the Effects of Compression Ratio, Engine Speed and Equivalence Ratio on HCCI Combustion of DME

    DEFF Research Database (Denmark)

    Pedersen, Troels Dyhr; Schramm, Jesper

    2007-01-01

    An experimental study has been carried out on the homogeneous charge compression ignition (HCCI) combustion of Dimethyl Ether (DME). The study was performed as a parameter variation of engine speed and compression ratio on excess air ratios of approximately 2.5, 3 and 4. The compression ratio...... was adjusted in steps to find suitable regions of operation, and the effect of engine speed was studied at 1000, 2000 and 3000 RPM. It was found that leaner excess air ratios require higher compression ratios to achieve satisfactory combustion. Engine speed also affects operation significantly....

  10. Investigation of Spark Ignition and Autoignition in Methane and Air Using Computational Fluid Dynamics and Chemical Reaction Kinetics. A numerical Study of Ignition Processes in Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Nordrik, R.

    1993-12-01

    The processes in the combustion chamber of internal combustion engines have received increased attention in recent years because their efficiencies are important both economically and environmentally. This doctoral thesis studies the ignition phenomena by means of numerical simulation methods. The fundamental physical relations include flow field conservation equations, thermodynamics, chemical reaction kinetics, transport properties and spark modelling. Special attention is given to the inclusion of chemical kinetics in the flow field equations. Using his No Transport of Radicals Concept method, the author reduces the computational efforts by neglecting the transport of selected intermediate species. The method is validated by comparison with flame propagation data. A computational method is described and used to simulate spark ignition in laminar premixed methane-air mixtures and the autoignition process of a methane bubble surrounded by hot air. The spark ignition simulation agrees well with experimental results from the literature. The autoignition simulation identifies the importance of diffusive and chemical processes acting together. The ignition delay times exceed the experimental values found in the literature for premixed ignition delay, presumably because of the mixing process and lack of information on low temperature reactions in the skeletal kinetic mechanism. Transient turbulent methane jet autoignition is simulated by means of the KIVA-II code. Turbulent combustion is modelled by the Eddy Dissipation Concept. 90 refs., 81 figs., 3 tabs.

  11. Wastewater off-gas to electricity: A look at energy recovery using the internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Hawkins, S.C. [Eckenfelder Inc., Greenville, SC (United States)

    1997-12-31

    Historically, publicly owned treatment works (POTWs) have not been regulated for air pollutant emissions. Federal, state, and local regulatory agencies have placed increased scrutiny on POTW volatile organic compound (VOC) and hazardous air pollutant (HAP) emissions. In fact, the USEPA is developing Maximum Achievable Control Technology (MACT) standards for publicly owned facilities that receive and treat sewage and wastewater from residential, commercial, and industrial generators. Once promulgated, this standard will require POTWs to limit and control HAP emissions. One option available for the control of HAP emissions from wastewater facilities is the use of the internal combustion (IC) engine-generator systems to convert wastewater off-gas to energy. Single or multiple IC engines can be arranged to utilize wastewater off-gas in place of natural gas and diesel fuel to produce electricity. The electricity generated can then be used to power the treatment facility or sold to the local utility. These systems utilize an otherwise wasted energy resource while significantly reducing HAP and VOC emissions from the wastewater treatment process. This paper will discuss the principles of using the internal combustion engine for energy recovery and examine the technical and economic benefits involved with their use at POTW facilities.

  12. Design, calibration and error analysis of instrumentation for heat transfer measurements in internal combustion engines

    Science.gov (United States)

    Ferguson, C. R.; Tree, D. R.; Dewitt, D. P.; Wahiduzzaman, S. A. H.

    1987-01-01

    The paper reports the methodology and uncertainty analyses of instrumentation for heat transfer measurements in internal combustion engines. Results are presented for determining the local wall heat flux in an internal combustion engine (using a surface thermocouple-type heat flux gage) and the apparent flame-temperature and soot volume fraction path length product in a diesel engine (using two-color pyrometry). It is shown that a surface thermocouple heat transfer gage suitably constructed and calibrated will have an accuracy of 5 to 10 percent. It is also shown that, when applying two-color pyrometry to measure the apparent flame temperature and soot volume fraction-path length, it is important to choose at least one of the two wavelengths to lie in the range of 1.3 to 2.3 micrometers. Carefully calibrated two-color pyrometer can ensure that random errors in the apparent flame temperature and in the soot volume fraction path length will remain small (within about 1 percent and 10-percent, respectively).

  13. Combustion characteristics of a turbocharged DI compression ignition engine fueled with petroleum diesel fuels and biodiesel.

    Science.gov (United States)

    Canakci, Mustafa

    2007-04-01

    In this study, the combustion characteristics and emissions of two different petroleum diesel fuels (No. 1 and No. 2) and biodiesel from soybean oil were compared. The tests were performed at steady state conditions in a four-cylinder turbocharged DI diesel engine at full load at 1400-rpm engine speed. The experimental results compared with No. 2 diesel fuel showed that biodiesel provided significant reductions in PM, CO, and unburned HC, the NO(x) increased by 11.2%. Biodiesel had a 13.8% increase in brake-specific fuel consumption due to its lower heating value. However, using No. 1 diesel fuel gave better emission results, NO(x) and brake-specific fuel consumption reduced by 16.1% and 1.2%, respectively. The values of the principal combustion characteristics of the biodiesel were obtained between two petroleum diesel fuels. The results indicated that biodiesel may be blended with No. 1 diesel fuel to be used without any modification on the engine.

  14. Design, calibration and error analysis of instrumentation for heat transfer measurements in internal combustion engines

    Science.gov (United States)

    Ferguson, C. R.; Tree, D. R.; Dewitt, D. P.; Wahiduzzaman, S. A. H.

    1987-01-01

    The paper reports the methodology and uncertainty analyses of instrumentation for heat transfer measurements in internal combustion engines. Results are presented for determining the local wall heat flux in an internal combustion engine (using a surface thermocouple-type heat flux gage) and the apparent flame-temperature and soot volume fraction path length product in a diesel engine (using two-color pyrometry). It is shown that a surface thermocouple heat transfer gage suitably constructed and calibrated will have an accuracy of 5 to 10 percent. It is also shown that, when applying two-color pyrometry to measure the apparent flame temperature and soot volume fraction-path length, it is important to choose at least one of the two wavelengths to lie in the range of 1.3 to 2.3 micrometers. Carefully calibrated two-color pyrometer can ensure that random errors in the apparent flame temperature and in the soot volume fraction path length will remain small (within about 1 percent and 10-percent, respectively).

  15. Transport Phenomena.

    Science.gov (United States)

    McCready, Mark J.; Leighton, David T.

    1987-01-01

    Discusses the problems created in graduate chemical engineering programs when students enter with a wide diversity of understandings of transport phenomena. Describes a two-semester graduate transport course sequence at the University of Notre Dame which focuses on fluid mechanics and heat and mass transfer. (TW)

  16. Influence of process parameters on coal combustion performance. Review, experiments and engineering modeling

    Energy Technology Data Exchange (ETDEWEB)

    Lans, R.P. van der

    1997-04-01

    The objective of this study is to improve the understanding of nitrogen oxide formation and carbon burnout during the combustion of pulverized coal, and to contribute to addressing the potential of chemical engineering models for the prediction of furnace temperatures, NO emissions and the amount of carbon in ash. To this purpose, the effect of coal quality on NO and burnout has been investigated experimentally, a radiation heat balance has been developed based on a simple chemical engineering methodology, and a mixing study has been conducted in order to describe the near burner macro mixing in terms of a reactor configuration. The influence of coal type and process conditions on NO formation and carbon burnout has been investigated experimentally in a 400 MW{sub e} corner fired boiler with over fire air, a 350 MW{sub e} opposed fired boiler, and in a 160 kW{sub t} pilot scale test rig. Three different coals were fired in each of the furnaces as part of the activities in group 3 of the European Union JOULE 2 Extension project `Atmospheric Pressure Combustion of Pulverized Coal and Coal Based Blends for Power Generation`. On the pilot scale test both single stage and air staged tests were performed. A simple, one-dimensional combustion and radiation heat transfer model has been developed for the furnace of full scale boilers. The model has been applied to the two boilers mentioned above, and is validated against measured temperatures and carbon in ash concentrations. A mixing study has been performed in order to initiate an investigation of the potential of chemical engineering models to predict NO from pulverized fuel burners. (EG) 11 refs.

  17. Large-eddy simulations of turbulent flows in internal combustion engines

    Science.gov (United States)

    Banaeizadeh, Araz

    The two-phase compressible scalar filtered mass density function (FMDF) model is further developed and employed for large-eddy simulations (LES) of turbulent spray combustion in internal combustion (IC) engines. In this model, the filtered compressible Navier-Stokes equations are solved in a generalized curvilinear coordinate system with high-order, multi-block, compact differencing schemes for the turbulent velocity and pressure. However, turbulent mixing and combustion are computed with a new two-phase compressible scalar FMDF model. The spray and droplet dispersion/evaporation are modeled with a Lagrangian method. A new Lagrangian-Eulerian-Lagrangian computational method is employed for solving the flow, spray and scalar equation. The pressure effect in the energy equation, as needed in compressible flows, is included in the FMDF formulation. The performance of the new compressible LES/FMDF model is assessed by simulating the flow field and scalar mixing in a rapid compression machine (RCM), in a shock tube and in a supersonic co-axial jet. Consistency of temperatures predicted by the Eulerian finite-difference (FD) and Lagrangian Monte Carlo (MC) parts of the LES/FMDF model are established by including the pressure on the FMDF. It is shown that the LES/FMDF model is able to correctly capture the scalar mixing in both compressible subsonic and supersonic flows. Using the new two-phase LES/FMDF model, fluid dynamics, heat transfer, spray and combustion in the RCM with flat and crevice piston are studied. It is shown that the temperature distribution in the RCM with crevice piston is more uniform than the RCM with flat piston. The fuel spray characteristics and the spray parameters affecting the fuel mixing inside the RCM in reacting and non-reacting flows are also studied. The predicted liquid penetration and flame lift-off lengths for respectively non-reacting and reacting sprays are found to compare well with the available experimental data. Temperatures and

  18. Causes of Combustion Instabilities with Passive and Active Methods of Control for practical application to Gas Turbine Engines

    Science.gov (United States)

    Cornwell, Michael D.

    Combustion at high pressure in applications such as rocket engines and gas turbine engines commonly experience destructive combustion instabilities. These instabilities results from interactions between combustion heat release, fluid mechanics and acoustics. This research explores the significant affect of unstable fluid mechanics processes in augmenting unstable periodic combustion heat release. The frequency of the unstable heat release may shift to match one of the combustors natural acoustic frequencies which then can result in significant energy exchange from chemical to acoustic energy resulting in thermoacoustic instability. The mechanisms of the fluid mechanics in coupling combustion to acoustics are very broad with many varying mechanisms explained in detail in the first chapter. Significant effort is made in understanding these mechanisms in this research in order to find commonalities, useful for mitigating multiple instability mechanisms. The complexity of combustion instabilities makes mitigation of combustion instabilities very difficult as few mitigation methods have historically proven to be very effective for broad ranges of combustion instabilities. This research identifies turbulence intensity near the forward stagnation point and movement of the forward stagnation point as a common link in what would otherwise appear to be very different instabilities. The most common method of stabilization of both premixed and diffusion flame combustion is through the introduction of swirl. Reverse flow along the centerline is introduced to transport heat and chemically active combustion products back upstream to sustain combustion. This research develops methods to suppress the movement of the forward stagnation point without suppressing the development of the vortex breakdown process which is critical to the transport of heat and reactive species necessary for flame stabilization. These methods are useful in suppressing the local turbulence at the forward

  19. Simulations of Multi Combustion Modes Hydrogen Engines for Heavy Duty Trucks

    Directory of Open Access Journals (Sweden)

    Alberto A. Boretti

    2012-01-01

    Full Text Available The paper presents the numerical study of a diesel direct injection heavy duty truck engine converted to hydrogen. The engine has a power turbine connected through a clutch and a continuously variable transmission to the crankshaft. The power turbine may be disconnected and by-passed when it is inefficient or inconvenient to use. The conversion is obtained by replacing the Diesel injector with a hydrogen injector and the glow plug with a jet ignition device. The hydrogen engine operates different modes of combustion depending on the relative phasing of the main injection and the jet ignition. The engine generally operates mostly in Diesel-like mode, with the most part of the main injection following the suitable creation in cylinder conditions by jet ignition. For medium-low loads, better efficienciy is obtained with the gasoline-like mode jet igniting the premixed homogeneous mixture at top dead centre. It’s permitted at higher loads or at very low loads for the excessive peak pressure or the mixture too lean to burn rapidly. The hydrogen engine has better efficiency than Diesel outputs and fuel conversion. Thanks to the larger rate of heat release, it has the opportunity to run closer to stoichiometry and the multi mode capabilities. The critical area for this engine development is found in the design of a hydrogen injector delivering the amount of fuel needed to the large volume cylinder within a Diesel-like injection time.

  20. Studies of the Combustion Process with Simultaneous Formaldehyde and OH PLIF in a Direct-Injected HCCI Engine

    Science.gov (United States)

    Richter, Mattias; Collin, Robert; Nygren, Jenny; Aldén, Marcus; Hildingsson, Leif; Johansson, Bengt

    This paper presents simultaneous laser based measurements of formaldehyde and OH-radical distributions in a 0.5 liter optical HCCI engine with direct injection. Formaldehyde is formed as an intermediate species when combusting hydrocarbons. The formation occurs through low temperature reactions in an early phase of the combustion process. Later in the process formaldehyde is being consumed. Formaldehyde is, therefore, used as indicator of the first stage of combustion and a marker of zones with low-temperature reactions. The OH radical is formed as an intermediate during the high temperature reactions, and is used as a marker of zones where the combustion is ongoing. The purpose of the investigation was to study how the combustion process is affected by the change in homogeneity that arises from early and late injection, respectively. The measurement technique used was planar laser-induced fluorescence where formaldehyde was excited at 355nm and OH at 283nm.

  1. H∞ control of combustion in diesel engines using a discrete dynamics model

    Science.gov (United States)

    Hirata, Mitsuo; Ishizuki, Sota; Suzuki, Masayasu

    2016-09-01

    This paper proposes a control method for combustion in diesel engines using a discrete dynamics model. The proposed two-degree-of-freedom control scheme achieves not only good feedback properties such as disturbance suppression and robust stability but also a good transient response. The method includes a feedforward controller constructed from the inverse model of the plant, and a feedback controller designed by an Hcontrol method, which reduces the effect of the turbocharger lag. The effectiveness of the proposed method is evaluated via numerical simulations.

  2. A Completely New Type of Actuator -or- This Ain't Your Grandfather's Internal Combustion Engine

    Science.gov (United States)

    Gore, Brian W.; Hawkins, Gary F.; Hess, Peter A.; Moore, Teresa A.; Fournier, Eric W.

    2010-01-01

    A completely new type of actuator - one that is proposed for use in a variety of environments from sea to land to air to space - has been designed, patented, built, and tested. The actuator is loosely based on the principle of the internal combustion engine, except that it is a completely closed system, only requiring electrical input, and the working fuel is water. This paper outlines the theory behind the electrolysis- and ignition-based cycle upon which the actuator operates and describes the performance capability test apparatus and results for the actuator. A mechanism application that harnessed the unit s power to twist a scaled rotor blade is also highlighted.

  3. Research and development on transonic compressor of high pressure ratio turbocharger for vehicle internal combustion engines

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The pressure ratio required for a turbocharger centrifugal compressor increases with internal combustion engine power density. High pressure ratio causes a transonic flow field at the impeller inducer. Transonic flow narrows the stable flow range and de-teriorates stage efficiency. In this work, an advanced high pressure ratio transonic compressor was designed. The experimental results show that the maximum pressure ratio of this turbocharger is about 4.2, the maximum efficiency is above 80% and the stable flow range at the designed rotating speed is up to 34%. A turbocharger with this transonic compressor has been applied to some vehicle research actually, and improved power density by 40%.

  4. Compression-cast light metal piston for internal combustion engines. Pressgegossener Leichtmetallkolben fuer Verbrennungskraftmaschinen

    Energy Technology Data Exchange (ETDEWEB)

    Mielke, S.; Henning, W.; Weiss, F.; Goelder, K.

    1991-05-16

    In a compression-cast light metal piston for internal combustion engines, fibre bodies made of short ceramic fibres, which are aligned parallel to a plane, are cast in. To improve the resistance to wear of the piston consisting of a heat-resistant magnesium alloy, the piston shank has a metallic, chemically or galvanically separate layer with a thickness of 10 to 30 m, and a hardness of 740 to 850 HV < 0.01, at least in the area of its friction surfaces.

  5. Simulation and Analyis of a Continuous Variable Cam Phasing Internal Combustion Engine

    OpenAIRE

    Hammarlund, Pär

    2008-01-01

    The development of fuel efficient internal combustion engines (ICE)have resulted in a variety of different solutions. One of those are the variable valve timing and an implemenation of such is the Continuous Variable Cam Phasing (CVCP). This thesis have used a simulation package, psPack, for the simulation of the gas exchange process for an ICE with CVCP. The purpose of the simulations was to investigate what kind of design parameters, e.g. the length of an intake pipe or the duration of comb...

  6. Achievement of the charge exchange work diminishing of an internal combustion engine in part load

    Directory of Open Access Journals (Sweden)

    Stefan POSTRZEDNIK

    2012-01-01

    Full Text Available Internal combustion engines, used for driving of different cars, occurs not only at full load, but mostly at the part load. The relative load exchange work at the full (nominal engine load is significantly low. At the part load of the IC engine its energy efficiency ηe is significantly lower than in the optimal (nominal field range of the performance parameters. One of the numerous reasons of this effect is regular growing of the relative load exchange work of the IC engine. It is directly connected with the quantitative regulation method commonly used in the IC engines. From the thermodynamic point of view - the main reason of this effect is the throttling process (causing exergy losses occurring in the inlet and outlet channels. The known proposals for solving of this problem are based on applying of the fully electronic control of the motion of inlet, outlet valves and new reference cycles.The idea presented in the paper leads to diminishing the charge exchange work of the IC engines. The problem can be solved using presented in the paper a new concept of the reference cycle (called as eco-cycle of IC engine. The work of the engine basing on the eco-cycle occurs in two 3-stroke stages; the fresh air is delivered only once for both stages, but in range of each stage a new portion of fuel is burned. Normally the charge exchange occurs once during each engine cycle realized. Elaborated proposition bases on the elimination of chosen charge exchange processes and through this the dropping of the charge exchange work can be achieved.

  7. On the identification of piston slap events in internal combustion engines using tribodynamic analysis

    Science.gov (United States)

    Dolatabadi, N.; Theodossiades, S.; Rothberg, S. J.

    2015-06-01

    Piston slap is a major source of vibration and noise in internal combustion engines. Therefore, better understanding of the conditions favouring piston slap can be beneficial for the reduction of engine Noise, Vibration and Harshness (NVH). Past research has attempted to determine the exact position of piston slap events during the engine cycle and correlate them to the engine block vibration response. Validated numerical/analytical models of the piston assembly can be very useful towards this aim, since extracting the relevant information from experimental measurements can be a tedious and complicated process. In the present work, a coupled simulation of piston dynamics and engine tribology (tribodynamics) has been performed using quasi-static and transient numerical codes. Thus, the inertia and reaction forces developed in the piston are calculated. The occurrence of piston slap events in the engine cycle is monitored by introducing six alternative concepts: (i) the quasi-static lateral force, (ii) the transient lateral force, (iii) the minimum film thickness occurrence, (iv) the maximum energy transfer, (v) the lubricant squeeze velocity and (vi) the piston-impact angular duration. The validation of the proposed methods is achieved using experimental measurements taken from a single cylinder petrol engine in laboratory conditions. The surface acceleration of the engine block is measured at the thrust- and anti-thrust side locations. The correlation between the theoretically predicted events and the measured acceleration signals has been satisfactory in determining piston slap incidents, using the aforementioned concepts. The results also exhibit good repeatability throughout the set of measurements obtained in terms of the number of events occurring and their locations during the engine cycle.

  8. Combustion Stability Characteristics of the Project Morpheus Liquid Oxygen / Liquid Methane Main Engine

    Science.gov (United States)

    Melcher, John C.; Morehead, Robert L.

    2014-01-01

    The project Morpheus liquid oxygen (LOX) / liquid methane (LCH4) main engine is a Johnson Space Center (JSC) designed 5,000 lbf-thrust, 4:1 throttling, pressure-fed cryogenic engine using an impinging element injector design. The engine met or exceeded all performance requirements without experiencing any in- ight failures, but the engine exhibited acoustic-coupled combustion instabilities during sea-level ground-based testing. First tangential (1T), rst radial (1R), 1T1R, and higher order modes were triggered by conditions during the Morpheus vehicle derived low chamber pressure startup sequence. The instability was never observed to initiate during mainstage, even at low power levels. Ground-interaction acoustics aggravated the instability in vehicle tests. Analysis of more than 200 hot re tests on the Morpheus vehicle and Stennis Space Center (SSC) test stand showed a relationship between ignition stability and injector/chamber pressure. The instability had the distinct characteristic of initiating at high relative injection pressure drop at low chamber pressure during the start sequence. Data analysis suggests that the two-phase density during engine start results in a high injection velocity, possibly triggering the instabilities predicted by the Hewitt stability curves. Engine ignition instability was successfully mitigated via a higher-chamber pressure start sequence (e.g., 50% power level vs 30%) and operational propellant start temperature limits that maintained \\cold LOX" and \\warm methane" at the engine inlet. The main engine successfully demonstrated 4:1 throttling without chugging during mainstage, but chug instabilities were observed during some engine shutdown sequences at low injector pressure drop, especially during vehicle landing.

  9. A numerical study on combustion process in a small compression ignition engine run dual-fuel mode (diesel-biogas)

    Science.gov (United States)

    Ambarita, H.; Widodo, T. I.; Nasution, D. M.

    2017-01-01

    In order to reduce the consumption of fossil fuel of a compression ignition (CI) engines which is usually used in transportation and heavy machineries, it can be operated in dual-fuel mode (diesel-biogas). However, the literature reviews show that the thermal efficiency is lower due to incomplete combustion process. In order to increase the efficiency, the combustion process in the combustion chamber need to be explored. Here, a commercial CFD code is used to explore the combustion process of a small CI engine run on dual fuel mode (diesel-biogas). The turbulent governing equations are solved based on finite volume method. A simulation of compression and expansions strokes at an engine speed and load of 1000 rpm and 2500W, respectively has been carried out. The pressure and temperature distributions and streamlines are plotted. The simulation results show that at engine power of 732.27 Watt the thermal efficiency is 9.05%. The experiment and simulation results show a good agreement. The method developed in this study can be used to investigate the combustion process of CI engine run on dual-fuel mode.

  10. Advanced Laser-Based Techniques for Gas-Phase Diagnostics in Combustion and Aerospace Engineering.

    Science.gov (United States)

    Ehn, Andreas; Zhu, Jiajian; Li, Xuesong; Kiefer, Johannes

    2017-03-01

    Gaining information of species, temperature, and velocity distributions in turbulent combustion and high-speed reactive flows is challenging, particularly for conducting measurements without influencing the experimental object itself. The use of optical and spectroscopic techniques, and in particular laser-based diagnostics, has shown outstanding abilities for performing non-intrusive in situ diagnostics. The development of instrumentation, such as robust lasers with high pulse energy, ultra-short pulse duration, and high repetition rate along with digitized cameras exhibiting high sensitivity, large dynamic range, and frame rates on the order of MHz, has opened up for temporally and spatially resolved volumetric measurements of extreme dynamics and complexities. The aim of this article is to present selected important laser-based techniques for gas-phase diagnostics focusing on their applications in combustion and aerospace engineering. Applicable laser-based techniques for investigations of turbulent flows and combustion such as planar laser-induced fluorescence, Raman and Rayleigh scattering, coherent anti-Stokes Raman scattering, laser-induced grating scattering, particle image velocimetry, laser Doppler anemometry, and tomographic imaging are reviewed and described with some background physics. In addition, demands on instrumentation are further discussed to give insight in the possibilities that are offered by laser flow diagnostics.

  11. Experimental and Numerical Research of a Novel Combustion Chamber for Small Gas Turbine Engines

    Directory of Open Access Journals (Sweden)

    Hybl R.

    2013-04-01

    Full Text Available New combustion chamber concept (based on burner JETIS-JET Induced Swirl for small gas turbine engine (up to 200kW is presented in this article. The combustion chamber concept is based on the flame stabilization by the generated swirl swirl generated by two opposite tangentially arranged jet tubes in the intermediate zone, this arrangement replaces air swirler, which is very complicated and expensive part in the scope of small gas turbines with annular combustion chamber. The mixing primary jets are oriented partially opposite to the main exhaust gasses flow, this enhances hot product recirculation and fuel-air mixing necessary for low NOx production and flame stability. To evaluate the designed concept a JETIS burner demonstrator (methane fuel was manufactured and atmospheric experimental measurements of CO, NOx for various fuel nozzles and jet tubes the configuration were done. Results of these experiments and comparison with CFD simulation are presented here. Practical application of the new chamber concept in small gas turbine liquid fuel combustor was evaluated (verified on 3 nozzles planar combustor sector test rig at atmospheric conditions results of the experiment and numerical simulation are also presented.

  12. Evaluating the Effectiveness of Modelling-Oriented Workshops for Engineering Undergraduates in the Field of Thermally Activated Phenomena

    Science.gov (United States)

    Battaglia, Onofrio Rosario; Di Paola, Benedetto; Persano Adorno, Dominique; Pizzolato, Nicola; Fazio, Claudio

    2017-09-01

    Two 20-h modelling-based workshops focused on the explanation of thermally activated phenomena were held at the University of Palermo, Italy, during the Academic Year 2014-2015. One of them was conducted by applying an inquiry-based approach, while the other, still based on laboratory and modelling activities, was not focused on inquiry. Seventy-two students belonging to the Undergraduate Program for Chemical Engineering attended the two workshops. The related content was focused on an à la Feynman unifying approach to thermally activated phenomena. Questionnaires were administered to the students of both groups, before and post instruction. Responses were analysed using k-means cluster analysis and students' inferred lines of reasoning about the description and explanation of phenomena were studied in both groups. We find that both workshops can be considered effective in improving student's reasoning skills. However, the inquiry-based approach revealed to be more effective than the traditional one in helping students to build mechanisms of functioning and explicative models and to identify common aspects in apparently different phenomena.

  13. EXPERIMENTAL COMBUSTION ANALYSIS OF A HSDI DIESEL ENGINE FUELLED WITH PALM OIL BIODIESEL-DIESEL FUEL BLENDS

    Directory of Open Access Journals (Sweden)

    JOHN AGUDELO

    2009-01-01

    Full Text Available Differences in the chemical nature between petroleum diesel fuels and vegetable oils-based fuels lead to differences in their physical properties affecting the combustion process inside the engine. In this work a detailed combustion diagnosis was applied to a turbocharged automotive diesel engine operating with neat palm oil biodiesel (POB, No. 2 diesel fuel and their blends at 20 and 50% POB by volume (B20 and B50 respectively. To isolate the fuel effect, tests were executed at constant power output without carrying out any modification of the engine or its fuel injection system. As the POB content in the blend increased, there was a slight reduction in the fuel/air equivalence ratio from 0.39 (B0 to 0.37 (B100, an advance of injection timing and of start of combustion. Additionally, brake thermal efficiency, combustion duration, maximum mean temperature, temperature at exhaust valve opening and exhaust gas efficiency decreased; while the peak pressure, exergy destruction rate and specific fuel consumption increased. With diesel fuel and the blends B20 and B50 the same combustion stages were noticed. However, as a consequence of the differences pointed out, the thermal history of the process was affected. The diffusion combustion stage became larger with POB content. For B100 no premixed stage was observed.

  14. Numerical Investigation Into Effect of Fuel Injection Timing on CAI/HCCI Combustion in a Four-Stroke GDI Engine

    Science.gov (United States)

    Cao, Li; Zhao, Hua; Jiang, Xi; Kalian, Navin

    2006-02-01

    The Controlled Auto-Ignition (CAI) combustion, also known as Homogeneous Charge Compression Ignition (HCCI), was achieved by trapping residuals with early exhaust valve closure in conjunction with direct injection. Multi-cycle 3D engine simulations have been carried out for parametric study on four different injection timings in order to better understand the effects of injection timings on in-cylinder mixing and CAI combustion. The full engine cycle simulation including complete gas exchange and combustion processes was carried out over several cycles in order to obtain the stable cycle for analysis. The combustion models used in the present study are the Shell auto-ignition model and the characteristic-time combustion model, which were modified to take the high level of EGR into consideration. A liquid sheet breakup spray model was used for the droplet breakup processes. The analyses show that the injection timing plays an important role in affecting the in-cylinder air/fuel mixing and mixture temperature, which in turn affects the CAI combustion and engine performance.

  15. The influence of charge stratification on the spectral signature of partially premixed combustion in a light-duty optical engine

    KAUST Repository

    Najafabadi, M. Izadi

    2017-03-25

    The origin of light emission during low-temperature combustion in a light-duty IC engine is investigated by high-speed spectroscopy in both HCCI and PPC regimes. Chemiluminescence and thermal radiation are expected to be the dominant sources of light emission during combustion. A method has been developed to distinguish chemiluminescence from thermal radiation, and different chemiluminescing species could be identified. Different combustion modes and global equivalence ratios are analyzed in this manner. The results indicate that the spectral signature (270–540 nm range) of the combustion is highly dependent on the stratification level. A significant broadband chemiluminescence signal is detected and superimposed on all spectra. This broadband chemiluminescence signal can reach up to 100 percent of the total signal in HCCI combustion, while it drops to around 80 percent for stratified combustion (PPC). We show that this broadband signal can be used as a measure for the heat release rate. The broadband chemiluminescence did also correlate with the equivalence ratio quite well in both HCCI and PPC regimes, suggesting that the total emission in the spectral region of 330–400 nm can serve as a proxy of equivalence ratio and the rate of heat release. Regarding C2* chemiluminescence, we see two different chemical mechanisms for formation of C2* in the PPC regime: first during the early stage of combustion by the breakup of bigger molecules and the second during the late stage of combustion when soot particles are forming.

  16. The influence of charge stratification on the spectral signature of partially premixed combustion in a light-duty optical engine

    Science.gov (United States)

    Najafabadi, M. Izadi; Egelmeers, Luc; Somers, Bart; Deen, Niels; Johansson, Bengt; Dam, Nico

    2017-04-01

    The origin of light emission during low-temperature combustion in a light-duty IC engine is investigated by high-speed spectroscopy in both HCCI and PPC regimes. Chemiluminescence and thermal radiation are expected to be the dominant sources of light emission during combustion. A method has been developed to distinguish chemiluminescence from thermal radiation, and different chemiluminescing species could be identified. Different combustion modes and global equivalence ratios are analyzed in this manner. The results indicate that the spectral signature (270-540 nm range) of the combustion is highly dependent on the stratification level. A significant broadband chemiluminescence signal is detected and superimposed on all spectra. This broadband chemiluminescence signal can reach up to 100 percent of the total signal in HCCI combustion, while it drops to around 80 percent for stratified combustion (PPC). We show that this broadband signal can be used as a measure for the heat release rate. The broadband chemiluminescence did also correlate with the equivalence ratio quite well in both HCCI and PPC regimes, suggesting that the total emission in the spectral region of 330-400 nm can serve as a proxy of equivalence ratio and the rate of heat release. Regarding C2* chemiluminescence, we see two different chemical mechanisms for formation of C2* in the PPC regime: first during the early stage of combustion by the breakup of bigger molecules and the second during the late stage of combustion when soot particles are forming.

  17. L'évolution des combustibles pour moteurs thermiques Evolution of Fuels for Thermal Engines

    Directory of Open Access Journals (Sweden)

    Balaceanu J. C.

    2006-11-01

    Full Text Available Depuis la crise pétrolière, l'accroissement des prix et les craintes de pénurie ont conduit à adapter les moteurs aux combustibles disponibles. Si la situation apparaît comme moins tendue, l'industrie des machines thermiques, qui pendant longtemps a eu comme partenaire une industrie du pétrole très sûre, se trouve cependant confrontée à un marché des combustibles incertain dans son ravitaillement et surtout dans ses prix. Les progrès des moteurs diesel et des turbines à gaz, dûs à une meilleure adaptation à leur usage et aussi à l'évolution de la technologie, supposent que les combustibles n'apporteront aucune contrainte majeure en quantité ou en qualité. La modification des usages dévolus désormais au pétrole entraînera une réduction de la coupe lourde et un raffinage plus profond des bruts avec en particulier un développement du craquage catalytique et de la viscoréduction. Or, ces différentes opérations de conversion peuvent conduire à une détérioration de la qualité des combustibles moins grave pour le gazole que pour le fuel lourd. Dans les différents domaines impliqués, les parades technologiques sont en cours de développement. L'industrie des machines thermiques, qui poursuit l'amélioration des engins, et l'industrie du pétrole, qui recherche une réduction des prix des combustibles, sont donc conduites à un compromis optimal auquel elles ne peuvent accéder efficacement qu'en définissant les règles du jeu c'est-à-dire des spécifications internationales rigoureuses des combustibles. Since the oil crisis, the increase in prices and fears of a shortage have led to the adapting of engines to what fuels are available. Whereas the situation now seems somewhat less tense, the thermal machinery industry, which for a long time had a very reliable petroleum industry as its partner, nonetheless finds itself confronted with an uncertain fuel market with regard to supplies and especially to prices. Progress

  18. Influence of engine speed and the course of the fuel injection characteristics on forming the average combustion temperature in the cylinder of turbo diesel engine

    Directory of Open Access Journals (Sweden)

    Piotr GUSTOF

    2007-01-01

    Full Text Available Average combustion temperatures inside a turbo diesel engine for the same load and the same total doze of fuel for two rotational speeds: 2004 [rpm] and 4250 [rpm] are presented in this paper. The aim of this work is also the evaluation of the influence of the temporary course of the fuel injection characteristics on forming temperature in theengine cylinder space for these temperatures. The calculations were carried out by means of two zone combustion model.

  19. Stand for Experimental Evaluation of Effects of Hydrogen Use in Internal Combustion Engines

    Directory of Open Access Journals (Sweden)

    Levente B.

    2015-04-01

    Full Text Available Hydroxy gas or the Brown gas or simply HHO, as it is called more often now days, is a highly flammable gas that has been around since the beginning of the XX-th century, when scientist Yull Brown has dedicated his work to study the properties and means of production of HHO by water electrolysis. In the second half of the century, the oil crisis, the simplicity of HHO production and its high combustion temperature and flame propagation have spurred the interest of ”garage inventors” around the world, who started doing practical experiments with HHO injection on personal vehicles and power-generators, in trying to reduce gas mileage, increase the engine performance and lower tailpipe emissions. Today, this technology is being rediscovered, again due to higher fuel prices and this time also due to some increasing concerns over global warming. Many have learned that HHO injection into the IC engine improves the gas mileage and reduces emissions, some reporting fuel savings of up to 40%, while others even claim to have reached the performance of operating their engines on HHO entirely produced onboard of the running vehicle. There are also reports that claim increased life span of the engine and engine lubrication, due to reduction effect of HHO on the solid hydrocarbon depositions onto the engine critical components, like pistons, valves, cylinder walls, etc. In this regard, the University Politehnica Timisoara Department of Mechanical Machines, Equipment and Transportation and Department for Applied Chemistry and Engineering of Inorganic Compounds and Environment, have joined together in a project to study and understand the mechanism that take place during HHO injection to IC engines, quantify the benefits and develop safer, better and more reliable materials for HHO on-demand and on-board production by water electrolysis.

  20. Numerical modeling on homogeneous charge compression ignition combustion engine fueled by diesel-ethanol blends

    Directory of Open Access Journals (Sweden)

    Hanafi H.

    2016-01-01

    Full Text Available This paper investigates the performance and emission characteristics of HCCI engines fueled with oxygenated fuels (ethanol blend. A modeling study was conducted to investigate the impact of ethanol addition on the performance, combustion and emission characteristics of a Homogeneous Charge Compression Ignition (HCCI engine fueled by diesel. One dimensional simulation was conducted using the renowned commercial software for diesel and its blend fuels with 5% (E5 and 10% ethanol (E10 (in vol. under full load condition at variable engine speed ranging from 1000 to 2750 rpm with 250 rpm increment. The model was then validated with other researcher’s experimental result. Model consists of intake and exhaust systems, cylinder, head, valves and port geometries. Performance tests were conducted for volumetric efficiency, brake engine torque, brake power, brake mean effective pressure, brake specific fuel consumption, and brake thermal efficiency, while exhaust emissions were analyzed for carbon monoxide (CO and unburned hydrocarbons (HC. The results showed that blending diesel with ethanol increases the volumetric efficiency, brake specific fuel consumption and brake thermal efficiency, while it decreases brake engine torque, brake power and brake mean effective pressure. In term of emission characteristics, the CO emissions concentrations in the engine exhaust decrease significantly with ethanol as additive. But for HC emission, its concentration increase when apply in high engine speed. In conclusion, using Ethanol as fuel additive blend with Diesel operating in HCCI shows a good result in term of performance and emission in low speed but not recommended to use in high speed engine. Ethanol-diesel blends need to researched more to make it commercially useable.

  1. Spray ignition measurements in a constant volume combustion vessel under engine-relevant conditions

    Science.gov (United States)

    Ramesh, Varun

    Pressure-based and optical diagnostics for ignition delay (ID) measurement of a diesel spray from a multi-hole nozzle were investigated in a constant volume combustion vessel (CVCV) at conditions similar to those in a conventional diesel engine at the start of injection (SOI). It was first hypothesized that compared to an engine, the shorter ID in a CVCV was caused by NO, a byproduct of premixed combustion. The presence of a significant concentration of NO+NO2 was confirmed experimentally and by using a multi-zone model of premixed combustion. Experiments measuring the effect of NO on ID were performed at conditions relevant to a conventional diesel engine. Depending on the temperature regime and the nature of the fuel, NO addition was found to advance or retard ignition. Constant volume ignition simulations were capable of describing the observed trends; the magnitudes were different due to the physical processes involved in spray ignition, not modeled in the current study. The results of the study showed that ID is sensitive to low NO concentrations (<100 PPM) in the low-temperature regime. A second source of uncertainty in pressure-based ID measurement is the systematic error associated with the correction used to account for the speed of sound. Simultaneous measurements of volumetric OH chemiluminescence (OHC) and pressure during spray ignition found the OHC to closely resemble the pressure-based heat release rate for the full combustion duration. The start of OHC was always found to be shorter than the pressure-based ID for all fuels and conditions tested by 100 ms. Experiments were also conducted measuring the location and timing of high-temperature ignition and the steady-state lift-off length by high-speed imaging of OHC during spray ignition. The delay period calculated using the measured ignition location and the bulk average speed of sound was in agreement with the delay between OHC and the pressure-based ID. Results of the study show that start of OHC

  2. Control concepts for a gasoline HCCI combustion engine; Strategien zur Regelung von HCCI-Brennverfahren

    Energy Technology Data Exchange (ETDEWEB)

    Karrelmeyer, Roland; Fischer, Wolfgang [Robert Bosch GmbH, Stuttgart (Germany). CR/AEH; Graf, Gerald [Robert Bosch GmbH, Stuttgart (Germany). DGS-EC/ESG; Scherrer, Daniel [Robert Bosch GmbH, Stuttgart (Germany). GS/ECS1; Hathout, Jean-Pierre [Bosch Thermotechnology Sanayi ve Ticaret, A.S. Organize Sanayi Boelgesi, Manisa (Turkey)

    2009-07-01

    In this paper, we discuss an in-cylinder-pressure based controls concept for a HCCI-engine with internal exhaust-gas trapping. Combustion is controlled via the fuel- and air-path. The controls concept is based upon a combination of a feed-forward and a feed-back path. The work has been carried out on gasoline engines with direct-injection and different types of flexible valve trains. In a first step it will be considered a fully flexible type of valve train. On based of cost optimal aspects flexibility will be decreased which resulted in a partly flexible valve train with cam phasers an e. g. two step lift control. A control strategy based on this type of valve train also will be considered. (orig.)

  3. Method for Making Measurements of the Post-Combustion Residence Time in a Gas Turbine Engine

    Science.gov (United States)

    Miles, Jeffrey H (Inventor)

    2015-01-01

    A system and method of measuring a residence time in a gas-turbine engine is provided, whereby the method includes placing pressure sensors at a combustor entrance and at a turbine exit of the gas-turbine engine and measuring a combustor pressure at the combustor entrance and a turbine exit pressure at the turbine exit. The method further includes computing cross-spectrum functions between a combustor pressure sensor signal from the measured combustor pressure and a turbine exit pressure sensor signal from the measured turbine exit pressure, applying a linear curve fit to the cross-spectrum functions, and computing a post-combustion residence time from the linear curve fit.

  4. Valve Fault Diagnosis in Internal Combustion Engines Using Acoustic Emission and Artificial Neural Network

    Directory of Open Access Journals (Sweden)

    S. M. Jafari

    2014-01-01

    Full Text Available This paper presents the potential of acoustic emission (AE technique to detect valve damage in internal combustion engines. The cylinder head of a spark-ignited engine was used as the experimental setup. The effect of three types of valve damage (clearance, semicrack, and notch on valve leakage was investigated. The experimental results showed that AE is an effective method to detect damage and the type of damage in valves in both of the time and frequency domains. An artificial neural network was trained based on time domain analysis using AE parametric features (AErms, count, absolute AE energy, maximum signal amplitude, and average signal level. The network consisted of five, six, and five nodes in the input, hidden, and output layers, respectively. The results of the trained system showed that the AE technique could be used to identify the type of damage and its location.

  5. Improved automated diagnosis of misfire in internal combustion engines based on simulation models

    Science.gov (United States)

    Chen, Jian; Bond Randall, Robert

    2015-12-01

    In this paper, a new advance in the application of Artificial Neural Networks (ANNs) to the automated diagnosis of misfires in Internal Combustion engines(IC engines) is detailed. The automated diagnostic system comprises three stages: fault detection, fault localization and fault severity identification. Particularly, in the severity identification stage, separate Multi-Layer Perceptron networks (MLPs) with saturating linear transfer functions were designed for individual speed conditions, so they could achieve finer classification. In order to obtain sufficient data for the network training, numerical simulation was used to simulate different ranges of misfires in the engine. The simulation models need to be updated and evaluated using experimental data, so a series of experiments were first carried out on the engine test rig to capture the vibration signals for both normal condition and with a range of misfires. Two methods were used for the misfire diagnosis: one is based on the torsional vibration signals of the crankshaft and the other on the angular acceleration signals (rotational motion) of the engine block. Following the signal processing of the experimental and simulation signals, the best features were selected as the inputs to ANN networks. The ANN systems were trained using only the simulated data and tested using real experimental cases, indicating that the simulation model can be used for a wider range of faults for which it can still be considered valid. The final results have shown that the diagnostic system based on simulation can efficiently diagnose misfire, including location and severity.

  6. Experimental Investigation Of Biogas-Biodiesel Dual Fuel Combustion In A Diesel Engine

    Directory of Open Access Journals (Sweden)

    Ramesha D. K.

    2015-06-01

    Full Text Available This study is an attempt at achieving diesel fuel equivalent performance from diesel engines with maximum substitution of diesel with renewable fuels. In this context the study has been designed to analyze the influence of B20 algae biodiesel as a pilot fuel in a biodiesel biogas dual fuel engine, and results are compared to those of biodiesel and diesel operation at identical engine settings. Experiments were performed at various loads from 0 to 100 % of maximum load at a constant speed of 1500 rpm. In general, B20 algae biodiesel is compatible with diesel in terms of performance and combustion characteristics. Dual fuel mode operation displays lower thermal efficiency and higher fuel consumption than for other fuel modes of the test run across the range of engine loads. Dual fuel mode displayed lower emissions of NOx and Smoke opacity while HC and CO concentrations were considerably higher as compared to other fuels. In dual fuel mode peak pressure and heat release rate were slightly higher compared to diesel and biodiesel mode of operation for all engine loads.

  7. Reducing emissions by using special air filters for internal combustion engines

    Science.gov (United States)

    Birtok-Băneasă, C.; Raţiu, S. A.; Alexa, V.; Crăciun, A. L.; Josan, A.; Budiul-Berghian, A.

    2017-05-01

    This paper presents the experimental methodology to carry out functional performance tests for an air filter with a particular design of its housing, generically named Super absorbing YXV „Air by Corneliu”, patented and homologated by the Romanian Automotive Registry, to which numerous prizes and medals were awarded at national and international innovations salons. The tests were carried out in the Internal Combustion Engines Laboratory, within the specialization “Road vehicles” belonging to the Faculty of Engineering Hunedoara, component of Politehnica University of Timisoara. The scope of the study is to optimise the air intake into the engine cylinders by reducing the gas-dynamic resistances caused by the air filter and, therefore, to achieve higher energy efficiency, i.e. fuel consumption reduction and engine performance increase. We present some comparative values of various operating parameters of the engine fitted, in the first measuring session, with the original filter, and then with the studied filter. The data collected shows a reduction in fuel consumption by using this type of filter, which leads to lower emissions.

  8. Analysis of combustion in an ATAC engine with measurement of radical luminescence; Radical hakko keisoku ni yoru ATAC engine no nensho kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Park, Y.; Oguma, H.; Ueda, H.; Iida, N. [Keio University, Tokyo (Japan)

    1997-10-01

    In order to make clear of the combustion mechanism and the frame structure in two stake, so called, active thermo-atmosphere combustion (ATAC) engine fueled by gasoline and methanol, we measured the 2-demensional images of OH, CH and C2 radical band spectra in both ATAC and SI combustion mode. From the results of pressure data in the cylinder, the heat release rate was calculated. We evaluated the correlation of radical luminescence intensity and the rate of heat release. 3 refs., 4 figs., 2 tabs.

  9. Methodology for processing pressure traces used as inputs for combustion analyses in diesel engines

    Science.gov (United States)

    Rašić, Davor; Vihar, Rok; Žvar Baškovič, Urban; Katrašnik, Tomaž

    2017-05-01

    This study proposes a novel methodology for designing an optimum equiripple finite impulse response (FIR) filter for processing in-cylinder pressure traces of a diesel internal combustion engine, which serve as inputs for high-precision combustion analyses. The proposed automated workflow is based on an innovative approach of determining the transition band frequencies and optimum filter order. The methodology is based on discrete Fourier transform analysis, which is the first step to estimate the location of the pass-band and stop-band frequencies. The second step uses short-time Fourier transform analysis to refine the estimated aforementioned frequencies. These pass-band and stop-band frequencies are further used to determine the most appropriate FIR filter order. The most widely used existing methods for estimating the FIR filter order are not effective in suppressing the oscillations in the rate- of-heat-release (ROHR) trace, thus hindering the accuracy of combustion analyses. To address this problem, an innovative method for determining the order of an FIR filter is proposed in this study. This method is based on the minimization of the integral of normalized signal-to-noise differences between the stop-band frequency and the Nyquist frequency. Developed filters were validated using spectral analysis and calculation of the ROHR. The validation results showed that the filters designed using the proposed innovative method were superior compared with those using the existing methods for all analyzed cases. Highlights • Pressure traces of a diesel engine were processed by finite impulse response (FIR) filters with different orders • Transition band frequencies were determined with an innovative method based on discrete Fourier transform and short-time Fourier transform • Spectral analyses showed deficiencies of existing methods in determining the FIR filter order • A new method of determining the FIR filter order for processing pressure traces was

  10. Analysis of biomass and waste gasification lean syngases combustion for power generation using spark ignition engines.

    Science.gov (United States)

    Marculescu, Cosmin; Cenuşă, Victor; Alexe, Florin

    2016-01-01

    The paper presents a study for food processing industry waste to energy conversion using gasification and internal combustion engine for power generation. The biomass we used consisted in bones and meat residues sampled directly from the industrial line, characterised by high water content, about 42% in mass, and potential health risks. Using the feedstock properties, experimentally determined, two air-gasification process configurations were assessed and numerically modelled to quantify the effects on produced syngas properties. The study also focused on drying stage integration within the conversion chain: either external or integrated into the gasifier. To comply with environmental regulations on feedstock to syngas conversion both solutions were developed in a closed system using a modified down-draft gasifier that integrates the pyrolysis, gasification and partial oxidation stages. Good quality syngas with up to 19.1% - CO; 17% - H2; and 1.6% - CH4 can be produced. The syngas lower heating value may vary from 4.0 MJ/Nm(3) to 6.7 MJ/Nm(3) depending on process configuration. The influence of syngas fuel properties on spark ignition engines performances was studied in comparison to the natural gas (methane) and digestion biogas. In order to keep H2 molar quota below the detonation value of ⩽4% for the engines using syngas, characterised by higher hydrogen fraction, the air excess ratio in the combustion process must be increased to [2.2-2.8]. The results in this paper represent valuable data required by the design of waste to energy conversion chains with intermediate gas fuel production. The data is suitable for Otto engines characterised by power output below 1 MW, designed for natural gas consumption and fuelled with low calorific value gas fuels.

  11. COMBUSTION CHARACTERISTICS OF DIESEL ENGINE OPERATING ON JATROPHA OIL METHYL ESTER

    Directory of Open Access Journals (Sweden)

    Doddayaraganalu Amasegoda Dhananjaya

    2010-01-01

    Full Text Available Fuel crisis because of dramatic increase in vehicular population and environmental concerns have renewed interest of scientific community to look for alternative fuels of bio-origin such as vegetable oils. Vegetable oils can be produced from forests, vegetable oil crops, and oil bearing biomass materials. Non-edible vegetable oils such as jatropha oil, linseed oil, mahua oil, rice bran oil, karanji oil, etc., are potentially effective diesel substitute. Vegetable oils have reasonable energy content. Biodiesel can be used in its pure form or can be blended with diesel to form different blends. It can be used in diesel engines with very little or no engine modifications. This is because it has combustion characteristics similar to petroleum diesel. The current paper reports a study carried out to investigate the combustion, performance and emission characteristics of jatropha oil methyl ester and its blend B20 (80% petroleum diesel and 20% jatropha oil methyl ester and diesel fuel on a single-cylinder, four-stroke, direct injections, water cooled diesel engine. This study gives the comparative measures of brake thermal efficiency, brake specific energy consumption, smoke opacity, HC, NOx, ignition delay, cylinder peak pressure, and peak heat release rates. The engine performance in terms of higher thermal efficiency and lower emissions of blend B20 fuel operation was observed and compared with jatropha oil methyl ester and petroleum diesel fuel for injection timing of 20° bTDC, 23° bTDC and 26° bTDC at injection opening pressure of 220 bar.

  12. Intelligent Detector of Internal Combustion Engine Cylinder Pressure and Sensitivity Temperature Coefficient Compensation

    Directory of Open Access Journals (Sweden)

    Beirong Zheng

    2013-01-01

    Full Text Available The detecting device based on mechanical mechanism is far from the measurement of internal combustion engine cylinder explosion and compression pressure. This pressure detection is under the environment of pulsed gas (over 500 times per one minute and mechanical impactive vibration. Piezoresistive detection with silicon on insulator (SOI strain gauges to pressure seems to be a good solution to meet such special applications. In this work, separation by implanted oxygen (SIMOX wafer was used to fabricate the high temperature pressure sensor chip. For high accuracy and wide temperature range application, this paper also presents a novel pressure sensitivity temperature coefficient (TCS compensation method, using integrated constant current network. A quantitative compensation formula is introduced in mathematics. During experiments, the absolute value of the compensated TCS is easy to be 10 × 10−6/°C~100 × 10−6/°C by individual adjustment and calibration of each device’s temperature compensation. Therefore, the feasibility and practicability of this technology are tested. Again, the disadvantages are discussed after the research of the experiment data and the improvement methods are also given in the designing period. This technology exhibits the great potential practical value of internal combustion engine cylinder pressure with volume manufacturing.

  13. Time Delay Analysis of Turbofan Engine Direct and Indirect Combustion Noise Sources

    Science.gov (United States)

    Miles, Jeffrey Hilton

    2008-01-01

    The core noise components of a dual spool turbofan engine were separated by the use of a coherence function. A source location technique based on adjusting the time delay between the combustor pressure sensor signal and the far-field microphone signal to maximize the coherence and remove as much variation of the phase angle with frequency as possible was used. The discovery was made that for the 130o microphone a 90.027 ms time shift worked best for the frequency band from 0 to 200 Hz while a 86.975 ms time shift worked best for the frequency band from 200 to 400 Hz. Hence, the 0 to 200 Hz band signal took more time than the 200 to 400 Hz band signal to travel the same distance. This suggests the 0 to 200 Hz coherent cross spectral density band is partly due to indirect combustion noise attributed to entropy fluctuations, which travel at the flow velocity, interacting with the turbine. The signal in the 200 to 400 Hz frequency band is attributed mostly to direct combustion noise. Results are presented herein for engine power settings of 48, 54, and 60 percent of the maximum power setting

  14. Application of the Advanced Distillation Curve Method to Fuels for Advanced Combustion Engine Gasolines

    KAUST Repository

    Burger, Jessica L.

    2015-07-16

    © This article not subject to U.S. Copyright. Published 2015 by the American Chemical Society. Incremental but fundamental changes are currently being made to fuel composition and combustion strategies to diversify energy feedstocks, decrease pollution, and increase engine efficiency. The increase in parameter space (by having many variables in play simultaneously) makes it difficult at best to propose strategic changes to engine and fuel design by use of conventional build-and-test methodology. To make changes in the most time- and cost-effective manner, it is imperative that new computational tools and surrogate fuels are developed. Currently, sets of fuels are being characterized by industry groups, such as the Coordinating Research Council (CRC) and other entities, so that researchers in different laboratories have access to fuels with consistent properties. In this work, six gasolines (FACE A, C, F, G, I, and J) are characterized by the advanced distillation curve (ADC) method to determine the composition and enthalpy of combustion in various distillate volume fractions. Tracking the composition and enthalpy of distillate fractions provides valuable information for determining structure property relationships, and moreover, it provides the basis for the development of equations of state that can describe the thermodynamic properties of these complex mixtures and lead to development of surrogate fuels composed of major hydrocarbon classes found in target fuels.

  15. Accelerated Electromechanical Modeling of a Distributed Internal Combustion Engine Generator Unit

    Directory of Open Access Journals (Sweden)

    Serhiy V. Bozhko

    2012-07-01

    Full Text Available Distributed generation with a combustion engine prime mover is still widely used to supply electric power in a variety of applications. These applications range from backup power supply systems and combined wind-diesel generation to providing power in places where grid connection is either technically impractical or financially uneconomic. Modelling of such systems as a whole is extremely difficult due to the long-time load profiles needed and the computational difficulty of including small time-constant electrical dynamics with large time-constant mechanical dynamics. This paper presents the development of accelerated, reduced-order models of a distributed internal combustions engine generator unit. Overall these models are shown to achieve a massive improvement in the computational time required for long-time simulations while also achieving an extremely high level of dynamic accuracy. It is demonstrated how these models are derived, used and verified against benchmark models created using established techniques. Throughout the paper the modelling set as a whole, including multi level detail, is presented, detailed and finally summarised into a crucial tool for general system investigation and multiple target optimisation.

  16. Effects of Fuel Temperature on Injection Process and Combustion of Dimethyl Ether Engine.

    Science.gov (United States)

    Guangxin, Gao; Zhulin, Yuan; Apeng, Zhou; Shenghua, Liu; Yanju, Wei

    2013-12-01

    To investigate the effects of fuel temperature on the injection process in the fuel-injection pipe and the combustion characteristics of compression ignition (CI) engine, tests on a four stroke, direct injection dimethyl ether (DME) engine were conducted. Experimental results show that as the fuel temperature increases from 20 to 40 °C, the sound speed is decreased by 12.2%, the peak line pressure at pump and nozzle sides are decreased by 7.2% and 5.6%, respectively. Meanwhile, the injection timing is retarded by 2.2 °CA and the injection duration is extended by 0.8 °CA. Accordingly, the ignition delay and the combustion duration are extended by 0.7 °CA and 4.0 °CA, respectively. The cylinder peak pressure is decreased by 5.4%. As a result, the effective thermal efficiency is decreased, especially for temperature above 40 °C. Before beginning an experiment, the fuel properties of DME, including the density, the bulk modulus, and the sound speed were calculated by "ThermoData." The calculated result of sound speed is consistent with the experimental results.

  17. Internal combustion engine run on biogas is a potential solution to meet Indonesia emission target

    Science.gov (United States)

    Ambarita, Himsar

    2017-09-01

    Indonesia has released two different Greenhouse Gas (GHG) emissions reduction targets. The first target, released in 2009, is reduction GHG emissions 26% from Business-as-Usual (BAU) level using own budget and up 41% if supported international aids by 2020. The second target is reduction 29% and 41% from BAU by 2030 using own budget and with international support, respectively. In this paper, the BAU emissions and emissions reduction target of these two targets are elaborated. In addition, the characteristics of emissions from transportation sector are discussed. One of the potential mitigation actions is switching fuel in transportation sector. The results the most promising mitigation action in the transportation is switching oil fuel with biofuel. The Government of Indonesia (GoI) focuses on using biodiesel and bioethanol to run internal combustion engine in transportation sector and biogas is aimed to fuel power plant unit. However, there is very limited of success stories on using biogas in the power plant. The barriers and challenges will be discussed here. It is suggested to run internal combustion engine with biogas.

  18. Engine emissions and combustion analysis of biodiesel from East African countries

    Directory of Open Access Journals (Sweden)

    Paul Maina

    2014-03-01

    Full Text Available Environmental, availability and financial problems associated with fossil fuels encourage the manufacture and use of biodiesel. In this study, vegetable oil was extracted from Jatropha curcas seeds sourced from Kenya and Tanzania. A two-step acid base catalytic transesterification process was used to produce biodiesel because of the amount of free fatty acids present in the oil. The test rig used in the experiments was an Audi, 1.9-litre, turbocharged direct injection, compression ignition engine. Emissions were measured using an Horiba emission analyser system while combustion data was collected by a data acquisition system, from which cylinder pressure and rate of heat release of the test engine in every crank angle were calculated. The two biodiesels showed better emission characteristics than the fossil diesel included in the tests for comparison purposes. Cylinder pressure and heat release of the biodiesel were also within acceptable ranges. However, the emission and combustion characteristics differed between the two biodiesels a result likely related to their different origins. These findings prove that the source of biodiesel is an important factor to consider.

  19. The mechanism of lead catalysis of double-base rocket propellant combustion: Super-rate burning and the plateau/mesa phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Graham, W.H.; Neidert, J.B. (Thiokol Corp., Huntsville, AL (United States))

    1993-10-01

    Although double-base propellants contain a fairly complex mixture of ingredients, the most unstable compounds present are the nitrate esters, nitrocellulose and nitrate ester plasticizers, which represent the majority of most formulations; usually the ballistic additives, a lead compound and often carbon, represent from 1% to 5% of the total propellant. Energetic additives such as RDX and HMX are often present, but these nitramines are less responsive to lead catalysis which is characterized by a region of super-rate burning at lower pressures followed by a plateau region at higher pressure as the catalytic effectiveness appears to decrease and often a mesa region as the burn rate actually decreases with pressure. To explain both the super-rate burning and the plateau/mesa phenomena, one should logically examine the chemistry of decomposition of the nitrate esters to explain both lead catalysis and the apparent loss of catalysis; fortunately, examination of the reported chemistry of nitrate esters and several more recent investigations, which used sophisticated experimental techniques to examine double-base propellant combustion, provide support for a comprehensive mechanism to explain both.

  20. Heat insulation of combustion chamber walls - A measure to decrease the fuel consumption of I. C. engines

    Energy Technology Data Exchange (ETDEWEB)

    Woschni, G.; Spindler, W.; Kolesa, K.

    1987-01-01

    Experimental investigations were made with a single-cylinder direct-injection Diesel engine with heat-insulated piston. The most important result is an inferior economy compared with the not insulated aluminum-piston engine. It was found that this phenomenon is not caused by neither a changed combustion process nor increased blowby nor different friction losses, but rather by a drastic increase of the heat transfer coefficient during the first part of combustion with increasing surface temperature. This is taken into account in a modified equation for the heat transfer coefficient. Cycle-simulations using this modified equation show that there is neither a gain in fuel economy of naturally aspirated nor of turbocharged nor of turbocompound Diesel engines with ''heat insulated'' combustion chamber walls.