WorldWideScience

Sample records for combustible cartridge case

  1. Combustible Cartridge Case Characterization

    Science.gov (United States)

    1984-02-01

    University (NYU) has resulted in the selection of two cross-linked melamine / formaldehyde acrylic styrene resin systems that can be used in the beater additive... melamine resin Akaradit II stabilizer 20. ABSTRACT (con) Test coupons of combustible cartridge case material were fabricated using these recommended...and agitated for 30 min before the pH was slowly lowered to 3 with p-toluene sulfonic acid. In order to maintain this pH in the felting tank, it was

  2. A comparative study of combustible cartridge case materials

    Directory of Open Access Journals (Sweden)

    Wei-tao Yang

    2017-06-01

    Full Text Available Foamed combustible material based on polymer bonded RDX was fabricated using CO2 as foaming agent. The inner structures of felted and foamed combustible materials were presented by SEM. The two materials presented different formulations and inner porous structures. The combustion behaviors of felted and foamed materials were investigated by closed vessel test. Simultaneously, the co-combustion behavior of combustible cartridge case with 7-perf consolidated propellants was also investigated. The results of closed vessel test is applicable to gun system which is made of the foamed combustible material as component.

  3. Study of Brass Obturator Design for Combustible Cartridge Case for 105mm Tank Gun Ammunition

    Directory of Open Access Journals (Sweden)

    R.K. Syal

    1997-07-01

    Full Text Available Brass cartridge case provides rearward obturation in the tank gun ammunition where the gun systedt has a sliding breech mechanism. In the case of semi-combustible cartridge case (SCCC ammunition, obturation is provided by a smal1 metal stub. The mechanism of obturation and obturator design for kinetic energy and high explosive squash heat (HESH, SCCC ammunition of 105mm tank gun have been studied. The dynamic firing results for SCCC ammunition for 105 mm tank gun reveal height 115 mm provides perfect obturation. The ballistic performance of SCCC ammunition is comparable with that of the brass-cartridged round in the pressure range 150-450 MPa.

  4. Polyvinyl Acetate Resin as a Binder Effecting Mechanical and CombustionProperties of Combustible Cartridge Case Formulations

    OpenAIRE

    M.T. Shedge; C.H. Patel; S.K. Tadkod; G.D. Murthy

    2008-01-01

    Several combustible cartridge case (CCC) formulations containing nitrocellulose (NC) as anenergetic ingredient with diphenylamine (DPA) as stabiliser, cellulose fiber as reinforcing materialand polyvinyl acetate (PVAc) as a binder are processed to form combustible discs. A formulationcontaining  nitrocellulose (83 parts), cellulose (17 parts) , PVAc (20 parts) and  diphenylamine(1 part) by weight was observed with the improvement of  mechanical properties without anyadverse effect on combusti...

  5. Polyvinyl Acetate Resin as a Binder Effecting Mechanical and CombustionProperties of Combustible Cartridge Case Formulations

    Directory of Open Access Journals (Sweden)

    M.T. Shedge

    2008-05-01

    Full Text Available Several combustible cartridge case (CCC formulations containing nitrocellulose (NC as anenergetic ingredient with diphenylamine (DPA as stabiliser, cellulose fiber as reinforcing materialand polyvinyl acetate (PVAc as a binder are processed to form combustible discs. A formulationcontaining  nitrocellulose (83 parts, cellulose (17 parts , PVAc (20 parts and  diphenylamine(1 part by weight was observed with the improvement of  mechanical properties without anyadverse effect on combustion characteristics, safety parameters and compatibility with triplebase multi-tubular propellant. Dynamic firing performance was also satisfactory.

  6. Indicator strip and portable instrument technologies for determining nitroesters or moisture in combustible cartridge cases

    Energy Technology Data Exchange (ETDEWEB)

    Griest, W.H.; Ho, C.H.; Moneyhun, J.H.; Agouridis, D.C.; Gayle, T.M.; Bates, B.E.

    1993-10-01

    The sometimes large round-to-round variability observed in accelerated environmental testing, plus difficulties in quantifying the environmental histories of a given round suggest the need for nondestructive rapid tests of munitions to supplement lifetime prediction models in quality assurance of munitions. Technologies are being developed for reagent strips which can be affixed to rounds and which will visually indicate the presence and extent of nitroester migration by a visible color change. A solid state adaptation of a modified Griess reagent develops a red-purple color in the presence of nitroesters. Performance of current designs tested in the laboratory suggest a short-term (ca. one month) single usage. Dielectric capacitance is a promising means for rapid, nondestructive moisture determinations using a portable battery-powered instrument. Laboratory studies with a modified, inexpensive, commercial device have demonstrated fast (a few seconds) detection of case wall moisture content.

  7. Development of STR profiles from firearms and fired cartridge cases.

    Science.gov (United States)

    Horsman-Hall, Katie M; Orihuela, Yvette; Karczynski, Stephanie L; Davis, Ann L; Ban, Jeffrey D; Greenspoon, Susan A

    2009-09-01

    Fired cartridge cases are a common type of evidence found at crime scenes. However, due to the high chamber temperatures and touch nature of this evidence, DNA testing is not commonly sought because it is believed DNA is only present in low levels, whether it is due to initial low levels of DNA and/or DNA degradation from the heat or inhibition of the PCR reaction. Moreover, very few laboratories report STR typing success with fired cases. This study focused on obtaining STR profiles from fired cartridge cases using the AmpFlSTR MiniFiler kit, which is designed to amplify DNA from low level, inhibited, and degraded samples. Comparisons to other STR amplification kits were also conducted. In attempt to simulate casework, random individuals loaded cartridges into a firearm. DNA was recovered from the fired cartridge cases using the double swab technique and extracted using an automated large volume DNA IQ method. Initially, testing focused on known shedders handling cartridges for 30s prior to firing. A significantly greater number of alleles was obtained following amplification with the MiniFiler kit versus the PowerPlex 16 BIO kit. No alleles were observed using the Identifiler kit. In an attempt to better simulate casework, a random selection of laboratory personnel handled shotshells for as long as needed to load and fire the weapon. In this mock sample study, the MiniFiler kit successfully amplified an average of 22% of expected alleles from DNA recovered from shotshell cases versus the PowerPlex 16 BIO kit where an average of 7% of alleles were observed. However, the total number of alleles obtained from the two kits was not significantly different. The quality of the DNA obtained from fired cases was studied with evidence of inhibition in at least 11% of shotshell case samples. After swabbing the head and the hull of three shotshell cases separately, a significantly greater number of alleles was obtained from the hull as opposed to the head of the fired

  8. Intelligent image capture of cartridge cases for firearms examiners

    Science.gov (United States)

    Jones, Brett C.; Guerci, Joseph R.

    1997-02-01

    The FBI's DRUGFIRETM system is a nationwide computerized networked image database of ballistic forensic evidence. This evidence includes images of cartridge cases and bullets obtained from both crime scenes and controlled test firings of seized weapons. Currently, the system is installed in over 80 forensic labs across the country and has enjoyed a high degree of success. In this paper, we discuss some of the issues and methods associated with providing a front-end semi-automated image capture system that simultaneously satisfies the often conflicting criteria of the many human examiners visual perception versus the criteria associated with optimizing autonomous digital image correlation. Specifically, we detail the proposed processing chain of an intelligent image capture system (IICS), involving a real- time capture 'assistant,' which assesses the quality of the image under test utilizing a custom designed neural network.

  9. Statistical Analysis of Firearms/Toolmarks Interpretation of Cartridge Case Evidence Using IBIS and Bayesian Networks

    Science.gov (United States)

    2015-10-24

    Cases , KB Morris, E Law, R Jefferys, & E Fabyanic, 67th AAFS Meeting, Orlando , FL, February 2015 Poster: Using likelihood ratios for source attribution...of Glock™ model 21 fired cartridge cases , C Hefner, & KB Morris, 67th AAFS Meeting, Orlando , FL, February 2015. (c) Presentations Number of...and known cartridge cases ) to assess the performance of the Bayesian networks created during the study . In all cases the sets were submitted in a

  10. Experiment and simulation of launching process of a small-diameter steel cartridge case

    Institute of Scientific and Technical Information of China (English)

    Han-dong ZHAO; Jia-qing XIE; Zhi-peng LI; Hui-suo ZHANG

    2014-01-01

    In order to explore the rules of the deformation force during the launching of a small-diameter steel cartridge, the semi-closed bomb test method is used to test the greatest strains on chamber outer wall under the different chamber pressures. The pressure curves of cartridge chamber are measured in experiment, and the tensile test data of cartridge are loaded into the numerical calculation to compare with the experimental data. The conclusion was obtained that the calculated results match better with the experimental results by considering strain rate bilinear kinematic hardening material constitutive model. The forces on the various parts of the cartridge during launching and their deformation rules are achieved, in which the equivalent plastic strain decreases and the cylinder ring withstands the maximum equivalent stress when the cartridge case clings to the bore from the mouth to the bottom.

  11. Lubrication in the Drawing of Steel Cartridge Cases

    Science.gov (United States)

    1945-11-01

    loss offensive odor than the sulfurized tallow and water, it was still very mossy and disagroeable. In addition, the heat generated during drawing is...then to add the sulfurizod additive. A dispersion containing 4% soap, 12% tallow , 3-4% of finoly divided filler and 0,5% or a reactive sulfurizod fatty...operations between draws. F, Sulfide Coating Quite early in the steel case program a sulfurized tallow containing small amounts of water was used in the

  12. Cartridge Casing Catcher With Reduced Firearm Ejection Port Flash and Noise

    Science.gov (United States)

    2009-05-26

    respective deflectors. The magnetic material is generally at least one of steel, Strontium and Barium ferrite , Samarium- Cobalt , Neody- mium -Iron...Boron, and Aluminum-Nickel- Cobalt alloy. Accordingly, the present invention may provide a cartridge casing catcher with reduced firearm ejection port...a Strontium and Barium ferrite , Samarium-Co- balt, Neodymium-Iron-Boron, other pennanently magnetic rare earth alloys, and Alnico (i.e., Aluminum

  13. A Modified Electrostatic Adsorption Apparatus for Latent Fingerprint Development on Unfired Cartridge Cases.

    Science.gov (United States)

    Xu, Jingyang; Zhang, Ziyuan; Zheng, Xiaochun; Bond, John W

    2016-12-13

    Visualization of latent fingerprints on metallic surfaces by the method of applying electrostatic charging and adsorption is considered as a promising chemical-free method, which has the merit of nondestruction, and is considered to be effective for some difficult situations such as aged fingerprint deposits or those exposed to environmental extremes. In fact, a portable electrostatic generator can be easily accessible in a local forensic technology laboratory, which is already widely used in the visualization of footwear impressions. In this study, a modified version of this electrostatic apparatus is proposed for latent fingerprint development and has shown great potential in visualizing fingerprints on metallic surfaces such as cartridge cases. Results indicate that this experimental arrangement can successfully develop aged latent fingerprints on metal surfaces, and we demonstrate its effectiveness compared with existing conventional fingerprint recovery methods.

  14. Fibrillation of Commercial Acrylic Fiber for Use in Combustible Cartridge Cases

    Science.gov (United States)

    1983-03-01

    mesh - 5.4% Conclusion Fibrillation poor when viewed under microscope; not usable for process. Experiment 8 Material Used du Pont Orlon, 5 denier...to the solution. 2 Crystals, technical grade, Witco Chemical, Brooklyn , N. Y. 11231. 52 Ai The material was microscopically checked at 10-minute

  15. Combustible Cartridge Cases, an Account of the Current Technology and Proposals for Future Development.

    Science.gov (United States)

    1986-10-01

    Division 43 Library, Materials Research Laboratorios .4 Librarian, Defence Signals Directorate library, Office of Defence Producton 4t Director...include inherent lack of mechanical strength, low porosity, vulnerability to penetration of water and water vapour, and problems related to materials ...8217- firing, supplement the energy of the propellant and lower wear and erosion of the tube. However, these materials lack the mechanical properties

  16. A comparison of surface topography characterization technologies for use in comparing spent bullet and cartridge case signatures

    Energy Technology Data Exchange (ETDEWEB)

    Batishko, C.R.; Hickman, B.J.; Cuta, F.M.

    1992-11-01

    The Pacific Northwest Laboratory was tasked by the US Department of Energy to provide technical assistance to the Federal Bureau of Investigation in evaluating and ranking technologies potentially useful in high-speed comparison of unique spent bullet and cartridge case surface signatures. Information sources included vendor input, current relevant literature, vendor phone contacts, other FBI resources, relevant PNL reports, and personal contact with numerous PNL technical staff. A comprehensive list of technologies was reduced to a list of 38 by grouping very similar methodologies, and further reduced to a short list of six by applying a set of five minimum functional requirements. A total of 14 primary criteria, many having secondary criteria, were subsequently used to evaluate each technology. The ranked short list results are reported and supported in this document, and their scores normalized to a hypothetical ideal system are as follows: (1) confocal microscopy 82.13; (2) laser dynamic focusing 72.04; (3)moire interferometry V70.94; (4)fringe field capacitance;(5)laser triangulation 66.18; (6)structured/sectioned light 65.55. Information available within the time/budget constraints which was used for the evaluation and ranking was not sufficiently detailed to evaluate specific implementations of the technologies. Each of the technologies in the short list was judged potentially capable of meeting the minimum requirements. Clever, novel engineering solutions resulting in a more cost-effective system, or a closer fit to the ``ideal system,`` could result in a reordering of the short list when actual technical proposals are evaluated. Therefore, it is recommended that a Request for Proposal not be limited to only the highest ranked technology, but include all six technologies in the short list.

  17. A comparison of surface topography characterization technologies for use in comparing spent bullet and cartridge case signatures

    Energy Technology Data Exchange (ETDEWEB)

    Batishko, C.R.; Hickman, B.J.; Cuta, F.M.

    1992-11-01

    The Pacific Northwest Laboratory was tasked by the US Department of Energy to provide technical assistance to the Federal Bureau of Investigation in evaluating and ranking technologies potentially useful in high-speed comparison of unique spent bullet and cartridge case surface signatures. Information sources included vendor input, current relevant literature, vendor phone contacts, other FBI resources, relevant PNL reports, and personal contact with numerous PNL technical staff. A comprehensive list of technologies was reduced to a list of 38 by grouping very similar methodologies, and further reduced to a short list of six by applying a set of five minimum functional requirements. A total of 14 primary criteria, many having secondary criteria, were subsequently used to evaluate each technology. The ranked short list results are reported and supported in this document, and their scores normalized to a hypothetical ideal system are as follows: (1) confocal microscopy 82.13; (2) laser dynamic focusing 72.04; (3)moire interferometry V70.94; (4)fringe field capacitance;(5)laser triangulation 66.18; (6)structured/sectioned light 65.55. Information available within the time/budget constraints which was used for the evaluation and ranking was not sufficiently detailed to evaluate specific implementations of the technologies. Each of the technologies in the short list was judged potentially capable of meeting the minimum requirements. Clever, novel engineering solutions resulting in a more cost-effective system, or a closer fit to the ideal system,'' could result in a reordering of the short list when actual technical proposals are evaluated. Therefore, it is recommended that a Request for Proposal not be limited to only the highest ranked technology, but include all six technologies in the short list.

  18. Pulse joining cartridges

    Energy Technology Data Exchange (ETDEWEB)

    Golovashchenko, Sergey Fedorovich; Bonnen, John Joseph Francis

    2016-08-23

    A pulsed joining tool includes a tool body that defines a cavity that receives an inner tubular member and an outer tubular member and a pulse joining cartridge. The tubular members are nested together with the cartridge being disposed around the outer tubular member. The cartridge includes a conductor, such as a wire or foil, that extends around the outer tubular member and is insulated to separate a supply segment from a return segment. A source of stored electrical energy is discharged through the conductor to join the tubular members with an electromagnetic force pulse.

  19. IBM 3480 tape cartridge

    CERN Multimedia

    1984-01-01

    The 3480 tape format is a magnetic tape data storage format developed by IBM. The cartridge contains a single reel. IBM’s 3480 cartridge tape system sought to replace the traditional reels of magnetic tape in the computer center. Because of their speed, reliability, durability and low media cost, these tapes and tape drives are still in high demand. A hallmark of the genre is transferability. Tapes recorded with one tape drive are generally readable on another drive, even if the tape drives were built by different manufacturers.

  20. Combustion

    CERN Document Server

    Glassman, Irvin

    1987-01-01

    Combustion, Second Edition focuses on the underlying principles of combustion and covers topics ranging from chemical thermodynamics and flame temperatures to chemical kinetics, detonation, ignition, and oxidation characteristics of fuels. Diffusion flames, flame phenomena in premixed combustible gases, and combustion of nonvolatile fuels are also discussed. This book consists of nine chapters and begins by introducing the reader to heats of reaction and formation, free energy and the equilibrium constants, and flame temperature calculations. The next chapter explores the rates of reactio

  1. Case history review--demilitarization combustion permits.

    Science.gov (United States)

    Gaborek, B J

    2000-02-01

    In May 1993, Administrative Browner of the U.S. Environmental Protection Agency (USEPA) announced that an indirect exposure health risk assessment was required for all hazardous waste combustion facilities seeking a Resource Conservation and Recovery Act permit. These types of risk assessments evaluate the health and environmental effects from inhalation of emissions (direct exposure) and from contact with environmental media and consumption of food products impacted by the emissions (indirect exposure). Completion of an indirect exposure risk assessment is often complicated by the various methodologies available for generating results and by the requirements of the regulating community. To minimize this complexity and to maximize consistency between risk assessments, the USEPA developed a number of detailed guidance documents. Site-specific conditions and toxicological data gaps, however, continue to present challenges not addressed by these guidance documents. This paper presents some of the specific challenges encountered by the U.S. Army Center for Health Promotion and Preventive Medicine when performing indirect exposure health risk assessments for several demilitarization combustion facilities.

  2. Penetrating chest trauma caused by a blank cartridge actuated rubber ball projectile: case presentation and ballistic investigation of an uncommon weapon type.

    Science.gov (United States)

    Frank, Matthias; Peters, Dieter; Klemm, Wolfram; Grossjohann, Rico; Ekkernkamp, Axel; Bockholdt, Britta; Seifert, Julia

    2017-05-23

    Recently, an increasing number of an uncommon weapon type based on a caliber 6-mm Flobert blank cartridge actuated revolver which discharges 10-mm-diameter rubber ball projectiles has been confiscated by police authorities following criminal offenses. A recent trauma case presenting with a penetrating chest injury occasioned an investigation into the basic ballistic parameters of this type of weapon. Kinetic energy E of the test projectiles was calculated between 5.8 and 12.5 J. Energy density ED of the test projectiles was close to or higher than the threshold energy density of human skin. It can be concluded that penetrating skin injuries due to free-flying rubber ball projectiles discharged at close range cannot be ruled out. However, in case of a contact shot, the main injury potential of this weapon type must be attributed to the high energy density of the muzzle gas jet which may, similar to well-known gas or alarm weapons, cause life-threatening or even lethal injuries.

  3. The Imation 9840 Tape Cartridge

    CERN Multimedia

    It’s a 20 GB uncompressed center-load cartridge used in StorageTek T9840 tape drives. The tape is a Metal Particle (MP) tape suitable for use on all Oracle/Sun/StorageTek 9840 A, B, C and D drives. The 9840 tape has an archival life of 15-30 years.

  4. Solid cartridge for a pulse weld forming electrode and method of joining tubular members

    Energy Technology Data Exchange (ETDEWEB)

    Bonnen, John Joseph Francis; Golovashchenko, Sergey Fedorovich; Mamutov, Alexander; Maison, Lloyd Douglas; Dawson, Scott Alwyn; deVries, James

    2016-02-23

    A cartridge assembly is disclosed for a pulse welding a first tube supported on a mandrel to a second tube. An outer tool is assembled over the second tube and a stored charge is discharged in the cartridge assembly. The cartridge comprises an annular conductor and a solid casing enveloping the conductor. The stored charge is electrically connected to the conductor and discharged through the conductor to compress the second tube and pulse weld the second tube to the first tube.

  5. Nanotechnology for forensic sciences: analysis of PDMS replica of the case head of spent cartridges by optical microscopy, SEM and AFM for the ballistic identification of individual characteristic features of firearms.

    Science.gov (United States)

    Valle, Francesco; Bianchi, Michele; Tortorella, Silvia; Pierini, Giovanni; Biscarini, Fabio; D'Elia, Marcello

    2012-10-10

    A novel application of replica molding to a forensic problem, viz. the accurate reproduction of the case head of gun and rifle cartridges, prior and after been shot, is presented. The fabrication of an arbitrary number of identical copies of the region hit by the firing pin and by the breech face is described. The replicas can be (i) handled without damaging the original evidence, (ii) distributed to different law enforcement agencies for comparison against other evidences found on crime scenes or ballistic tests of seized firearms, (iii) maintained on a file by the laboratories. A detailed analysis of the morphological features of the replicas has been carried out by standard microscopy techniques as well as by advanced microscopy such as scanning probe and scanning electron leading to a quantitative morphological characterization of the case heads down to the nanometer scale. The assignment of the cartridge replicas to the shooting weapon is demonstrated to hold below the micron scale, while it is hindered at the nanometer level both by the manufacturing differences and by eventual modifications occurring on the firing pin.

  6. A new coal distribution system for general industry: the coal cartridge system

    Energy Technology Data Exchange (ETDEWEB)

    Katoh, S.

    1986-01-01

    The author introduces the concept of a coal cartridge system (CCS) for the distribution of coal, outlines the flow of coal from coal centre to end user, explains distribution diagrams, and compares CCS combustion with the combustion system used in stoker boilers. Various problems being encountered in the development of practical coal cartridge systems are discussed. Finally, details are given of demonstration tests being carried out in connection with the supply terminal and boiler plant aspects of CCS (at the Tokuyama and Iwakuni Laboratories, respectively). 11 figs., 2 tabs.

  7. ALMA Band 5 Cartridge Performance

    Science.gov (United States)

    Billade, Bhushan; Lapkin, I.; Nystrom, O.; Sundin, E.; Fredrixon, M.; Finger, R.; Rashid, H.; Desmaris, V.; Meledin, D.; Pavolotsky, A.; Belitsky, Victor

    2010-03-01

    Work presented here concerns the design and performance of the ALMA Band 5 cold cartridge, one of the 10 frequency channels of ALMA project, a radio interferometer under construction at Atacama Desert in Chile. The Band 5 cartridge is a dual polarization receiver with the polarization separation performed by orthomode transducer (OMT). For each polarization, Band 5 receiver employs sideband rejection (2SB) scheme based on quadrature layout, with SIS mixers covering 163-211 GHz with 4-8 GHz IF. The LO injection circuitry is integrated with mixer chip and is implemented on the same substrate, resulting in a compact 2SB assembly. Amongst the other ALMA bands, the ALMA Band 5 being the lowest frequency band that uses all cold optics, has the largest mirror. Consequently, ALMA Band 5 mirror along with its support structure leaves very little room for placing OMT, mixers and IF subsystems. The constraints put by the size of cold optics and limited cartridge space, required of us to revise the original 2SB design and adopt a design where all the components like OMT, mixer, IF hybrid, isolators and IF amplifier are directly connected to each other without using any co-ax cables in-between. The IF subsystem uses the space between 4 K and 15 K stage of the cartridge and is thermally connected to 4 K stage. Avoiding co-ax cabling required use of custom designed IF hybrid, furthermore, due to limited cooling capacity at 4 K stage, resistive bias circuitry for the mixers is moved to 15 K stage and the IF hybrid along with an integrated bias-T is implemented using superconducting micro-strip lines. The E-probes for both LO and RF waveguide-to-microstrip transitions are placed perpendicular to the wave direction (back-piece configuration). The RF choke at the end of the probes provides a virtual ground for the RF/LO signal, and the choke is DC grounded to the chassis. The on-chip LO injection is done using a microstrip line directional coupler with slot-line branches in the

  8. StorageTek T10000 Data Cartridge

    CERN Multimedia

    This data cartridge works on several StorageTek systems. The goal is to provide cartridge compatibility across several system. It has been designed for space saving and ultra-high capacity tape. It permit to fulfill high-volume backup, archiving, and disaster recovery.

  9. Agricultural uses of alkaline fluidized bed combustion ash: case studies

    Energy Technology Data Exchange (ETDEWEB)

    Stout, W.L.; Daily, M.R.; Nickeson, T.L.; Svendson, R.L.; Thompson, G.P. [USDA-ARS, University Park, PA (United States)

    1997-06-01

    Successful programmes were developed by Ahlstrom Development Ash Corporation and Air Products and Chemical for using fluidized bed combustion ash as a substitute for agricultural lime on dairy farms in northern New York state and on fruit and nut crops in the San Joaquin Valley of California. The companies developed these programmes by utilizing the methodology developed through USDA-ARS research and working closely with agricultural consultants and regulatory agencies to ensure that the ash applications were both agronomically and environmentally sound. 1 ref.

  10. Technology Solutions Case Study: Combustion Safety Simplified Test Protocol

    Energy Technology Data Exchange (ETDEWEB)

    L. Brand, D. Cautley, D. Bohac, P. Francisco, L. Shen, and S. Gloss

    2015-12-01

    Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives.

  11. The dynamic interaction between combustible renewables and waste consumption and international tourism: the case of Tunisia.

    Science.gov (United States)

    Ben Jebli, Mehdi; Ben Youssef, Slim; Apergis, Nicholas

    2015-08-01

    This paper employs the autoregressive distributed lag (ARDL) bounds methodological approach to investigate the relationship between economic growth, combustible renewables and waste consumption, carbon dioxide (CO2) emissions, and international tourism for the case of Tunisia spanning the period 1990-2010. The results from the Fisher statistic of both the Wald test and the Johansen test confirm the presence of a long-run relationship among the variables under investigation. The stability of estimated parameters has been tested, while Granger causality tests recommend a short-run unidirectional causality running from economic growth and combustible renewables and waste consumption to CO2 emissions, a bidirectional causality between economic growth and combustible renewables and waste consumption and unidirectional causality running from economic growth and combustible renewables and waste consumption to international tourism. In the long-run, the error correction terms confirm the presence of bidirectional causality relationships between economic growth, CO2 emissions, combustible renewables and waste consumption, and international tourism. Our long-run estimates show that combustible renewables and waste consumption increases international tourism, and both renewables and waste consumption and international tourism increase CO2 emissions and output. We recommend that (i) Tunisia should use more combustible renewables and waste energy as this eliminates wastes from touristic zones and increases the number of tourist arrivals, leading to economic growth, and (ii) a fraction of this economic growth generated by the increase in combustible renewables and waste consumption should be invested in clean renewable energy production (i.e., solar, wind, geothermal) and energy efficiency projects.

  12. 42 CFR 84.190 - Chemical cartridge respirators: description.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Chemical cartridge respirators: description. 84.190... Cartridge Respirators § 84.190 Chemical cartridge respirators: description. (a) Chemical cartridge respirators including all completely assembled respirators which are designed for use as...

  13. 42 CFR 84.191 - Chemical cartridge respirators; required components.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Chemical cartridge respirators; required components... Chemical Cartridge Respirators § 84.191 Chemical cartridge respirators; required components. (a) Each chemical cartridge respirator described in § 84.190 shall, where its design requires, contain the...

  14. Scale-down prediction of industrial scale pleated membrane cartridge performance.

    Science.gov (United States)

    Brown, A I; Titchener-Hooker, N J; Lye, G J

    2011-04-01

    Flat-sheet membrane discs represent the current standard format used for experimental prediction of the scale-up of normal flow filtration processes. Use of this format is problematic, however, since the scale-down results typically show a 40-55% difference in performance compared to large-scale cartridges depending upon the feedstock used. In this work, novel pleated scale-down devices (Am=1.51-15.1×10(-3) m2) have been designed and fabricated. It is shown that these can more accurately predict the performance of industrial scale single-use pleated membrane cartridges (Am=1.06 m2) commonly used within biopharmaceutical manufacture. The single-use scale-down cartridges retain the same pleat characteristics of the larger cartridges, but require a reduced feed volume by virtue of a substantially diminished number of active membrane pleats. In this study, a 1,000-fold reduction in feed volume requirement for the scale-down cartridge with the smallest membrane area was achieved. The scale-down cartridges were tested both with clean water and a pepsin protein solution, showing flux-time relationships within 10% of the large-scale cartridge in both cases. Protein transmission levels were also in close agreement between the different scale cartridges. The similarity in performance of the scale-down and the large-scale cartridges, coupled with the low feed requirement, make such devices an excellent method by which rapid scale-up can be achieved during early stage process development for biopharmaceutical products. This new approach is a significant improvement over using flat-sheet discs as the quantitative similarity in performance with the large-scale leads to reliable scale-up predictions while requiring especially small volumes of feed material.

  15. Descemet′s tear due to injector cartridge tip deformity

    Directory of Open Access Journals (Sweden)

    Partha Biswas

    2012-01-01

    Full Text Available Foldable intraocular lens (IOL implantation using an injector system through 2.8-mm clear corneal incision following phacoemulsification provides excellent speedy postoperative recovery. In our reported case, a Sensar AR40e IOL (Abbott Medical Optics, USA was loaded into Emerald C cartridge, outside the view of the operating microscope, by the first assistant. The surgeon proceeded with the IOL injection through a 2.8-mm clear corneal incision after uneventful phacoemulsification, immediately following which he noted a Descemet′s tear with a rolled out flap of about 2 mm near the incision site. Gross downward beaking of the bevelled anterior end of the cartridge was subsequently noticed upon examination under the microscope. We suggest careful preoperative microscopic inspection of all instruments and devices entering the patient′s eyes to ensure maximum safety to the patient.

  16. 可燃药筒对模块装药燃烧残渣的影响%Influence of Combustible Case on Combustion Residue of Modular Charges

    Institute of Scientific and Technical Information of China (English)

    乔丽洁; 堵平; 廖昕; 王泽山

    2011-01-01

    针对某外贸型号火炮模块装药射击时存在燃烧残渣,影响后续装药和连续射击的问题,采用密闭爆发器定容燃烧模拟试验,对模块装药中两种可燃药筒燃烧(缓燃、速燃)后的残渣量进行了测试;同时以药包装药系统为参照系,研究了靶场射击中模块装药可燃药筒的燃烧残渣量,并对试验结果进行了比对.结果表明:近2/3的燃烧残渣是由可燃药筒产生的;增加可燃药筒中的硝化纤维素的含量,减少合成树脂粘合剂和纤维增强材料后,进行靶场射击试验,结果表明模块装药的燃烧残渣总量降低了2/3,基本消除了模块装药的射击残渣问题.%For the problem of combustion residue produced from some modular charge during firing, the residue amounts of two kinds of combustible cases ( slow burning and fast burning) after burning were measured through the closed bomb test. The combustion residue amounts of two combustible cases were also tested in the firing range by taking a bag propelling charge as a reference, and the two residue a-mounts were compared. The results show that near two-thirds combustion residue comes from the combustible case, and the total amount of combustion residue of the modular charge during firing is reduced by two-thirds after the synthetic resin binder and fiber reinforced material are reduced and the nitrocellulose is increased in the improved combustible case. Thus, the combustion residue of modular charge during firing is basically eliminated.

  17. StorageTek T10000 Tape Cartridge

    CERN Multimedia

    1985-01-01

    Oracle StorageTek T10000T2 cartridge has total capacity of 5 TB. It is actually manufactured by Fuji Film, uses Barium Ferrite (BaFe) particles technology data store, but is also equipped with RFID chip. There is over 1 km of tape inside of the cartridge with 3584 data tracks and it supports over 25000 load/unload cycles. The archival life is estimated to be around 30 years and uncorrected bit error rate is 10-19. CERN however usually migrates data to newer technologies roughly every 5 years in order to keep the footprint under control.

  18. Disposable cartridge biosensor platform for portable diagnostics

    Science.gov (United States)

    Yaras, Yusuf S.; Cakmak, Onur; Gunduz, Ali B.; Saglam, Gokhan; Olcer, Selim; Mostafazadeh, Aref; Baris, Ibrahim; Civitci, Fehmi; Yaralioglu, Goksen G.; Urey, Hakan

    2017-03-01

    We developed two types of cantilever-based biosensors for portable diagnostics applications. One sensor is based on MEMS cantilever chip mounted in a microfluidic channel and the other sensor is based on a movable optical fiber placed across a microfluidic channel. Both types of sensors were aimed at direct mechanical measurement of coagulation time in a disposable cartridge using plasma or whole blood samples. There are several similarities and also some important differences between the MEMS based and the optical fiber based solutions. The aim of this paper is to provide a comparison between the two solutions and the results. For both types of sensors, actuation of the cantilever or the moving fiber is achieved using an electro coil and the readout is optical. Since both the actuation and sensing are remote, no electrical connections are required for the cartridge. Therefore it is possible to build low cost disposable cartridges. The reader unit for the cartridge contains light sources, photodetectors, the electro coil, a heater, analog electronics, and a microprocessor. The reader unit has different optical interfaces for the cartridges that have MEMS cantilevers and moving fibers. MEMS based platform has better sensitivity but optomechanical alignment is a challenge and measurements with whole blood were not possible due to high scattering of light by the red blood cells. Fiber sensor based platform has relaxed optomechanical tolerances, ease of manufacturing, and it allows measurements in whole blood. Both sensors were tested using control plasma samples for activated-Partial-Thromboplastin-Time (aPTT) measurements. Control plasma test results matched with the manufacturer's datasheet. Optical fiber based system was tested for aPTT tests with human whole blood samples and the proposed platform provided repeatable test results making the system method of choice for portable diagnostics.

  19. Design And Case Study Of Combustion Of Muncipal Solid Waste And Refuse-Derived (Msw And Rdf With Conventional Fuels

    Directory of Open Access Journals (Sweden)

    M.Sudhakar

    2014-03-01

    Full Text Available Energy Production for used materials can be performed as mixed municipal solid waste (MSW incineration or as fuel for combustion. Recovered fuels are refuse-derived fuel (RDF, which is mechanically separated and processed from MSW.which is the source-separated, processed, dry combustable part of MSW. A one-year combustion of RDF with peat and coal was carried out in a 25 MW garbage boiler gratepower plant. The efficiency of the combustion temperature, boiler efficiency and the corrosion behaviour of the boiler were particular focuses of attention in this study. The combustion calculations and the MSW boiler design is carried out for three different cases in which combustion temperature is varied from 850°C to 950°C and fuel HHV varying from 1500 to 2500 Kcal/kg in the same power plant.. All RDF performed technically well and the emissions were low. Small particle size and stable feeding of RDF were important for effective combustion. Low CO emissions showed clean and efficient combustion. SO2emissions decreased, because part of the coal was replaced by RDF. HCl emissions increased when the chlorine content of the fuel mixture increased, because limestone injection was not used. Heavy metals concentrated to the fly ash in unreachable form.. Long-term co-combustion of 10% RDF with peat and coal did not cause any high temperature chlorine-induced corrosion of the super heater materials (420°C. The results showed that it is useful and technically possible to combustion temperature and boiler efficiency varies in the form of energy production in the normal power plants

  20. Fatalities caused by spherical bullets fired from blank cartridge guns in Istanbul, Turkey.

    Science.gov (United States)

    Uzün, Ibrahim; Büyük, Yalçin; Erkol, Zerrin; Ağritmiş, Hasan; Kir, Ziya

    2009-09-01

    Blank cartridge guns are generally regarded as being harmless and are not considered to be firearms in the legal sense in most countries. To show the danger of these guns upon simple modifications, we report 59 fatalities resulting from these simply modified blank cartridge guns in Istanbul, Turkey. The great majority of the victims were males and the age of those ranged from 11 to 61 years. In 55.9% of these cases, homicide was the origin followed by suicide (39%). The right temporal region was detected to be the preferred region in suicidal shots by blank cartridge guns with a frequency of 56.5%. In trial shots, all these guns were detected to discharge steel or lead spherical objects, generally 4 or 5 mm in diameter, successfully. Our findings strongly suggest that these guns should also be considered as handguns in the legal sense.

  1. Multicapillary electrophoresis disposable cartridge for bioseparations

    Science.gov (United States)

    Amirkhanian, Varoujan D.; Liu, Ming-Sun

    2003-07-01

    We have successfully demonstrated the development of a compact and cost-effective parallel multi-channel capillary electrophoresis system for bio-molecules analysis. The automated process includes a buffer/gel replenishment mechanism, high voltage control of fluidics and an automated sample tray transport capability. The bio-separation/analysis occurs in a disposable cartridge containing multi-column capillaries with integrated excitation optical fibers, detection micro-optics and a buffer reservoir common to all separation channels. Tests of this fully integrated system indicate, that large quantities of biological samples can be analyzed automatically in a short period with highly sensitive fluorescence detection.

  2. Determination of pressure drop across activated carbon fiber respirator cartridges.

    Science.gov (United States)

    Balanay, Jo Anne G; Lungu, Claudiu T

    2016-01-01

    Activated carbon fiber (ACF) is considered as an alternative adsorbent to granular activated carbon (GAC) for the development of thinner, lighter, and efficient respirators because of their larger surface area and adsorption capacities, thinner critical bed depth, lighter weight, and fabric form. This study aims to measure the pressure drop across different types of commercially available ACFs in respirator cartridges to determine the ACF composition and density that will result in acceptably breathable respirators. Seven ACF types in cloth (ACFC) and felt (ACFF) forms were tested. ACFs in cartridges were challenged with pre-conditioned constant air flow (43 LPM, 23°C, 50% RH) at different compositions (single- or combination-ACF type) in a test chamber. Pressure drop across ACF cartridges were obtained using a micromanometer, and compared among different cartridge configurations, to those of the GAC cartridge, and to the NIOSH breathing resistance requirements for respirator cartridges. Single-ACF type cartridges filled with any ACFF had pressure drop measurements (23.71-39.93 mmH2O) within the NIOSH inhalation resistance requirement of 40 mmH2O, while those of the ACFC cartridges (85.47±3.67 mmH2O) exceeded twice the limit due possibly to the denser weaving of ACFC fibers. All single ACFF-type cartridges had higher pressure drop compared to the GAC cartridge (23.13±1.14 mmH2O). Certain ACF combinations (2 ACFF or ACFC/ACFF types) resulted to pressure drop (26.39-32.81 mmH2O) below the NIOSH limit. All single-ACFF type and all combination-ACF type cartridges with acceptable pressure drop had much lower adsorbent weights than GAC (≤15.2% of GAC weight), showing potential for light-weight respirator cartridges. 100% ACFC in cartridges may result to respirators with high breathing resistance and, thus, is not recommended. The more dense ACFF and ACFC types may still be possibly used in respirators by combining them with less dense ACFF materials and/or by

  3. Criticality safety evaluation report for K Basin filter cartridges

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, D.G., Westinghouse Hanford

    1996-08-28

    A criticality safety evaluation of the K Basin filter cartridge assemblies was completed to support operations without criticality alarm system. The results show that for normal operation, the cartridge assembly is far below the safety limit of K eff = 0.95.

  4. Filter quality of pleated filter cartridges.

    Science.gov (United States)

    Chen, Chun-Wan; Huang, Sheng-Hsiu; Chiang, Che-Ming; Hsiao, Ta-Chih; Chen, Chih-Chieh

    2008-04-01

    The performance of dust cartridge filters commonly used in dust masks and in room ventilation depends both on the collection efficiency of the filter material and the pressure drop across the filter. Currently, the optimization of filter design is based only on minimizing the pressure drop at a set velocity chosen by the manufacturer. The collection efficiency, an equally important factor, is rarely considered in the optimization process. In this work, a filter quality factor, which combines the collection efficiency and the pressure drop, is used as the optimization criterion for filter evaluation. Most respirator manufacturers pleat the filter to various extents to increase the filtration area in the limit space within the dust cartridge. Six sizes of filter holders were fabricated to hold just one pleat of filter, simulating six different pleat counts, ranging from 0.5 to 3.33 pleats cm(-1). The possible electrostatic charges on the filter were removed by dipping in isopropyl alcohol, and the air velocity is fixed at 100 cm s(-1). Liquid dicotylphthalate particles generated by a constant output atomizer were used as challenge aerosols to minimize particle loading effects. A scanning mobility particle sizer was used to measure the challenge aerosol number concentrations and size distributions upstream and downstream of the pleated filter. The pressure drop across the filter was monitored by using a calibrated pressure transducer. The results showed that the performance of pleated filters depend not only on the size of the particle but also on the pleat count of the pleated filter. Based on filter quality factor, the optimal pleat count (OPC) is always higher than that based on pressure drop by about 0.3-0.5 pleats cm(-1). For example, the OPC is 2.15 pleats cm(-1) from the standpoint of pressure drop, but for the highest filter quality factor, the pleated filter needed to have a pleat count of 2.65 pleats cm(-1) at particle diameter of 122 nm. From the aspect of

  5. [Enforcement of type M 20 cal. 4 mm cartridges].

    Science.gov (United States)

    Dobosz, Tadeusz; Jaworski, Ryszard; Kawecki, Jerzy; Semiczek, Wiesław; Trnka, Jakub

    2002-01-01

    The aim of the paper was to investigate and compare the speed and energy of a bullet from 4 mm cal. cartridges of central ignition type M20, both original and transformed by addition of different kinds of propellants. Original cartridges are characterized by an average speed of the bullet of 144 m/s and average energy of 4.8 J. After transformation by the addition of on an average 31.3 mg of smokeless powder from a cartridge type LR'22, a maximum bullet speed of 299 m/s (average) and maximum energy of 21.2 joule (average) were reached. Our test showed that shots using transformed ammunition type M 20 cal. 4 mm can be dangerous for both health and life. Multiple M20 shot wounds may be very similar to single shot wounds caused by a shotshell cartridge fired from a shotgun weapon.

  6. Construction and optimisation of a cartridge filter for removing ...

    African Journals Online (AJOL)

    Construction and optimisation of a cartridge filter for removing fluoride in drinking water. ... It was found that the optimal conditions for the F- filter that gave the best results in removing of F- from water with minimum ... Article Metrics.

  7. Indústria de cartucho de toner sob a ótica da remanufatura: estudo de caso de um processo de melhoria Remanufacturing of toner cartridge: a case study of a improvement process

    Directory of Open Access Journals (Sweden)

    Cícero Ferreira Fernandes Costa Filho

    2006-04-01

    Full Text Available Este trabalho apresenta um estudo de caso de um processo de melhoria aplicado a uma indústria de remanufatura de cartuchos de toner. Inicialmente, é feita uma abordagem do processo de remanufatura procurando salientar as principais características que o diferenciam de um processo de manufatura convencional e a importância do mesmo diante das preocupações ambientais atuais. Através de três indicadores de desempenho propostos no trabalho fez-se um diagnóstico do processo de remanufatura quanto ao aproveitamento de peças recolhidas do campo, atendimento de pedidos dos clientes e quantidade de defeitos. No diagnóstico inicial realizado, os valores obtidos para esses critérios situaram-se abaixo das metas estabelecidas na empresa. Através da metodologia PDCA, identificaram-se oportunidades de melhorias em pontos críticos do processo de fabricação. A implantação dessas melhorias resultou em ganhos nos indicadores de desempenho da ordem de 12%. Algumas ferramentas clássicas foram utilizadas para auxiliar na implementação da metodologia PDCA destacando-se brainstorming, diagrama de Ishikawa e Controle Estatístico de Processo.This paper presents an improvement process applied in one remanufacturing toner cartridge industry. It, initially, presents a mapping of the stages of this process by attempting to highlight the main characteristics, which distinguish it from a conventional manufacturing process and emphasizes its importance as an of eco-efficient process aiming at achieving sustainable development. Through three performance indicators proposed by the work, a diagnosis of the existing process was carried out as to the reuse of parts gasthered in the field, fulfilment of customers'orders and quantity of production faults. At the initial diagnosis carried out, the values obtained for theses criteria were located below the established targets proposed by the company. Through the PDCA tool, improvement opportunities in critical

  8. Building America Case Study: Combustion Safety Simplified Test Protocol, Chicago Illinois, and Minneapolis, Minnesota

    Energy Technology Data Exchange (ETDEWEB)

    2015-12-01

    "9Combustion safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project provides several key results. State weatherization agencies do not generally track combustion safety failures, the data from those that do suggest that there is little actual evidence that combustion safety failures due to spillage from non-dryer exhaust are common and that only a very small number of homes are subject to the failures. The project team collected field data on 11 houses in 2015. Of these homes, two houses that demonstrated prolonged and excessive spillage were also the only two with venting systems out of compliance with the National Fuel Gas Code. The remaining homes experienced spillage that only occasionally extended beyond the first minute of operation. Combustion zone depressurization, outdoor temperature, and operation of individual fans all provide statistically significant predictors of spillage.

  9. From SCORM to Common Cartridge: A Step Forward

    Science.gov (United States)

    Gonzalez-Barbone, Victor; Anido-Rifon, Luis

    2010-01-01

    Shareable Content Object Reference Model (SCORM) was proposed as a standard for sharable learning object packaging, delivering and sequencing. Several years later, Common Cartridge (CC) is proposed as an enhancement of SCORM offering more flexibility and addressing needs not originally envisioned, namely assessment and web 2.0 standards, content…

  10. Ballistics of the 30-06 Rifle Cartridge

    Science.gov (United States)

    2012-11-30

    www.hodgdon.com/PDF/Youth%20Loads.pdf. 14. Endris, Graham. DETAIL SPECIFICATION CARTRIDGE,.300 WINCHESTER MAGNUM MATCH, MK 248 MOD 1 DODIC AB43...Jason T. Gomez and Arun Shukla November 2001, pp. 965-979. 10, November 2001, International Journal of Impact Engineering, Vol. 25, pp. 965-979

  11. EVALUATING A COMPOSITE CARTRIDGE FOR SMALL SYSTEM DRINKING WATER TREATMENT

    Science.gov (United States)

    A multi-layer, cartridge-based system that combines physical filtration with carbon adsorption and ultraviolet (UV) light disinfection has been developed to perform as a water treatment security device to protect homes against accidental or intentional contaminant events. A seri...

  12. EVALUATING A COMPOSITE CARTRIDGE FOR SMALL SYSTEM DRINKING WATER TREATMENT

    Science.gov (United States)

    A multi-layer, cartridge-based system that combines physical filtration with carbon adsorption and ultraviolet (UV) light disinfection has been developed to perform as a water treatment security device to protect homes against accidental or intentional contaminant events. A seri...

  13. 42 CFR 84.253 - Chemical-cartridge respirators; requirements and tests.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Chemical-cartridge respirators; requirements and... DEVICES Special Use Respirators § 84.253 Chemical-cartridge respirators; requirements and tests. (a... for chemical-cartridge respirators prescribed in Subpart L of this part are applicable to...

  14. 49 CFR 173.230 - Fuel cell cartridges containing hazardous material.

    Science.gov (United States)

    2010-10-01

    ...) For fuel cell cartridges contained in equipment, fuel cell systems must not charge batteries during... 49 Transportation 2 2010-10-01 2010-10-01 false Fuel cell cartridges containing hazardous material... Than Class 1 and Class 7 § 173.230 Fuel cell cartridges containing hazardous material. (a)...

  15. Two-gun suicide by simultaneous shots to the head: interdisciplinary reconstruction on the basis of scene investigation, autopsy findings, GSR analysis and examination of firearms, bullets and cartridge cases.

    Science.gov (United States)

    Grosse Perdekamp, Markus; Nadjem, Hadi; Merkel, Joachim; Braunwarth, Roland; Pollak, Stefan; Thierauf, Annette

    2011-07-01

    Suicidal shots fired simultaneously to the head from two handguns are rare. The authors report about a recent case in which a Smith & Wesson cal. 9 mm pistol and a Smith & Wesson cal. .357 Magnum revolver were used. Sitting on a sofa, a 33-year-old man (member of a shooting club) fired two simultaneous shots to the head; the pistol held in the left hand was discharged into the left temple, and the revolver held in the right hand was fired into the mouth. Both weapons remained in the respective hands. An upside-down muzzle imprint in the left temporal region and recoil injuries of a mandibular incisor, and the lower lip indicated that both the pistol and the revolver had been held in an inverted manner at the time of discharge. Blood stains (backspatter) and gunshot residues were present on both firing hands, whereas forward spatter originating from the exit wounds was deposited on the wall behind the suicide's head.

  16. Using Distonic Radical Ions to Probe the Chemistry of Key Combustion Intermediates: The Case of the Benzoxyl Radical Anion

    Science.gov (United States)

    Li, Cong; Lam, Adrian K. Y.; Khairallah, George N.; White, Jonathan M.; O'Hair, Richard A. J.; da Silva, Gabriel

    2013-04-01

    The benzoxyl radical is a key intermediate in the combustion of toluene and other aromatic hydrocarbons, yet relatively little experimental work has been performed on this species. Here, a combination of electrospray ionization (ESI), multistage mass spectrometry experiments, and density functional theory (DFT) calculations are used to examine the formation and fragmentation of a benzoxyl (benzyloxyl) distonic radical anion. Excited 4-carboxylatobenzoxyl radical anions were produced via two methods: (1) collision induced dissociation (CID) of the nitrate ester 4-(nitrooxymethyl)benzoate, -O2CC6H4CH2ONO2, and (2) reaction of ozone with the 4-carboxylatobenzyl radical anion, -O2CC6H4CH2 •. In neither case was the stabilized -O2CC6H4CH2O• radical anion intermediate detected. Instead, dissociation products at m/ z 121 and 149 were observed. These products are attributed to benzaldehyde (O2 -CC6H4CHO) and benzene (-O2CC6H5) products from respective loss of H and HCO radicals in the vibrationally excited benzoxyl intermediate. In no experiments was a product at m/ z 120 (i.e., -O2CC6H4 •) detected, corresponding to absence of the commonly assumed phenyl radical + CH2=O channel. The results reported suggest that distonic ions are useful surrogates for reactive intermediates formed in combustion chemistry.

  17. Refilling of carbon nanotube cartridges for 3D nanomanufacturing

    Science.gov (United States)

    Bekarevich, Raman; Toyoda, Masami; Baba, Shuichi; Nakata, Toshihiko; Hirahara, Kaori

    2016-03-01

    Metal-filled carbon nanotubes (CNTs) are known to be used as pen-tip injectors for 3D manufacturing on the nanoscale. However, the CNT interior cannot accumulate enough material to fabricate complex metallic nanostructures. Therefore a method for refilling the CNT cartridge needs to be developed. The strategy for refilling of CNT cartridges is suggested in this study. Controlled growth of gold nanowires in the interior of isolated CNTs using a real-time manipulator installed in a transmission electron microscope is reported herein. The encapsulation process of discrete gold nanoparticles in the hollow spaces of open-ended multi-wall CNTs was evaluated in detail. The experimental results reveal that the serial loading of isolated gold nanoparticles allows the control of the length of the loaded nanowires with nanometer accuracy. Thermophoresis and the coalescence of gold nanoparticles are assumed to be the primary mechanisms responsible for gold loading into a CNT cartridge.Metal-filled carbon nanotubes (CNTs) are known to be used as pen-tip injectors for 3D manufacturing on the nanoscale. However, the CNT interior cannot accumulate enough material to fabricate complex metallic nanostructures. Therefore a method for refilling the CNT cartridge needs to be developed. The strategy for refilling of CNT cartridges is suggested in this study. Controlled growth of gold nanowires in the interior of isolated CNTs using a real-time manipulator installed in a transmission electron microscope is reported herein. The encapsulation process of discrete gold nanoparticles in the hollow spaces of open-ended multi-wall CNTs was evaluated in detail. The experimental results reveal that the serial loading of isolated gold nanoparticles allows the control of the length of the loaded nanowires with nanometer accuracy. Thermophoresis and the coalescence of gold nanoparticles are assumed to be the primary mechanisms responsible for gold loading into a CNT cartridge. Electronic

  18. Comparison of systems for high speed surface flaw measurements of cartridges

    Energy Technology Data Exchange (ETDEWEB)

    Swinth, K. L.; Kirihara, L. J.; Coleman, W. J.

    1979-01-01

    Instrumentation to detect surface flaws in cartridge cases has been developed for high speed on-line inspection. Scattering of light from a line focused on the case surface indicates the presence of surface flaws and the instrumentation permits rough categorization of flaws into dents and scratches. Two methods of light detection have been implemented, and the purpose of this paper is to compare these techniques. The first technique uses fiber optics to collect the scattered light and carry it to a photomultiplier tube to generate a signal, which the second technique uses solid-state diodes to produce the signal. Angled surfaces such as the shoulder on the cartridge case influence the response of the fiber-optics due to the acceptance cone of the fibers. To circumvent this problem, the fibers must be judiciously positioned during manufacture of the fiber-optic bundles. The solid-state diodes do not have the limited acceptance angle and thus provide more uniform response. However, the diodes require placement of electronics on the rotating exam wheel near the detectors. The processing electronics for both systems are identical.

  19. Circulating fluidized bed combustion ash characterization. The case of the Provence 250 MW unit

    Energy Technology Data Exchange (ETDEWEB)

    Lecuyer, I.; Leduc, M. [Electricite de France (EDF), 78 - Chatou (France). Direction des Etudes et Recherches; Lefevre, R.; Ausset, P. [Paris-12 Univ., Creteil (France). Lab. Interuniversitaire des Systemes Atmospheriques

    1997-05-01

    The Provence 250 MW Circulating Fluidized Bed Combustion Unit (Gardanne, France) is burning a high sulfur (2 to 4%), high ash content (30%) local lignite. This peculiar fuel already contains about 15% of CaO which allows it to capture the sulfur dioxide in situ without adding any complementary sorbent. The ash chemical composition (bed ash and ESP ash) that reflects the particularities of the coal is presented. SEM and DRX observations confirm the presence of anhydrite CaSO{sub 4}, lime, CaS, quartz and traces of hematite. Most of particles are roughly-shaped but microspheres can also be detected in fly ash. The very high sulfate content may be worrying for the environment in disposals. Hardened samples do not seem to retain compounds from leaching: high quantities of calcium and sulfates are still leached from these crushed samples. (author) 10 refs.

  20. Unique case of fatal carbon monoxide poisoning in the absence of a combustible fossil fuel.

    Science.gov (United States)

    Morgan, D R; Poon, P; Titley, J; Jagger, S F; Rutty, G N

    2001-09-01

    A 37-year-old man died as a result of exposure to carbon monoxide within an apartment. An investigation of the apartment showed no gas appliances or gas supply to the apartment and no evidence of any combustion event to any part of the apartment or roof space. Inhalation of dichloromethane was excluded. Heating to the apartment was found to be via an electrical storage heater, the examination of which revealed that the cast-iron core and insulating material showed evidence of heat damage with significant areas devoid of carbon. This electric storage heater is hypothesized to be the source of carbon for the fatal production of carbon monoxide within the apartment.

  1. ACACIA Project – Development of a Post-Combustion CO2 Capture Process. Case of the DMXTM Process

    Directory of Open Access Journals (Sweden)

    Gomez A.

    2014-11-01

    Full Text Available The objective of the ACACIA project was to develop processes for post-combustion CO2 capture at a lower cost and with a higher energetic efficiency than first generation processes using amines such as MonoEthanolAmine (MEA which are now considered for the first Carbon Capture and Storage (CCS demonstrators. The partners involved in this project were: Rhodia (Solvay since then, Arkema, Lafarge, GDF SUEZ, Veolia Environnement, IFP Energies nouvelles, IRCE Lyon, LMOPS, LTIM, LSA Armines. To validate the relevance of the breakthrough processes studied in this project, techno-economic evaluations were carried out with comparison to the reference process using a 30 wt% MEA solvent. These evaluation studies involved all the industrial partners of the project, each partner bringing specific cases of CO2 capture on their industrial facilities. From these studies, only the process using demixing solvent, DMXTM, developed by IFPEN appears as an alternative solution to the MEA process.

  2. [Morphologic detection of Bacillus cereus in blank cartridges].

    Science.gov (United States)

    Rothschild, M A; Mülling, C

    1998-01-01

    Wound infections after gunshot wounds from live ammunition can produce serious complications. It is well known that projectiles per se are neither sterile nor does their firing cause sterilization. The germs on the surface of a projectile enter the body together with the projectile and are thus introduced into the wound together with skin bacteria. However it is less known that wound infections can occur in wounds caused by the gas jet from blank ammunition (mainly from shots at very close range). In such ammunition without a projectile, the propellant particles are usually contaminated with bacteria which find their way into the wound together with skin germs. In previous investigations, we have microbiologically detected the species Bacillus cereus in the propellant of blank cartridges. In the present study, we have applied scanning electron microscopic methods to find out which areas of the blank cartridges are colonized by these bacteria. For this purpose 20 blank cartridges, each from 4 different manufacturers, were electronmicroscopically examined. B. cereus only found on the surface of intact nitrocellulose particles but not in the interior of broken prepared propellant particles. Bacterial structures were not morphologically identified on black powder particles.

  3. The effectiveness of a novel cartridge-based bioreactor design in supporting liver cells.

    Science.gov (United States)

    Niu, Mei; Hammond, Paul; Coger, Robin N

    2009-10-01

    There are a number of applications--ranging from temporary strategies for organ failure to pharmaceutical testing--that rely on effective bioreactor designs. The significance of these devices is that they provide an environment for maintaining cells in a way that allows them to perform key cellular and tissue functions. In the current study, a novel cartridge-based bioreactor was developed and evaluated. Its unique features include its capacity for cell support and the adaptable design of its cellular space. Specifically, it is able to accommodate functional and reasonably sized tissue (>2.0 x 10(8) cells), and can be easily modified to support a range of anchorage-dependent cells. To evaluate its efficacy, it was applied to liver support in the current study. This involved evaluating the performance of rat primary hepatocytes within the unique cartridges in culture--sans bioreactor--and after being loaded within the novel bioreactor. Compared to collagen sandwich culture functional controls, hepatocytes within the unique cartridge design demonstrated significantly higher albumin production and urea secretion rates when cultured under dynamic flow conditions--reaching peak values of 170 +/- 22 microg/10(6) cells/day and 195 +/- 18 microg/10(6) cells/day, respectively. The bioreactor's effectiveness in supporting live and functioning primary hepatocytes is also presented. Cell viability at the end of 15 days of culture in the new bioreactor was 84 +/- 18%, suggesting that the new design is effective in maintaining primary hepatocytes for at least 2 weeks in culture. Liver-specific functions of urea secretion, albumin synthesis, and cytochrome P450 activity were also assessed. The results indicate that hepatocytes are able to achieve good functional performance when cultured within the novel bioreactor. This is especially true in the case of cytochrome P450 activity, where by day 15 of culture, hepatocytes within the bioreactor reached values that were 56.6% higher

  4. THE HYDROGEN-FUELLED INTERNAL COMBUSTION ENGINES FOR MARINE APPLICATIONS WITH A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Ibrahim S. Seddiek

    2015-03-01

    Full Text Available Modern marine power plants have been designed to improve the overall ship’s efficiency. This pushed the designers of marine machinery to search for unconventional fuels for these plants. During the previous years, diesel oil has been extensively used on-board ships. Due to the high price of light diesel oil and the environmental problems resulting from the use of heavy fuel oil, it has become necessary to search for an alternative to traditional fuels. As a result, natural gas fuel has been used on-board some types of ships, especially short-voyage cruise ships. Unfortunately, there are still some technical and logistic problems related to the use of natural gas as a fuel, especially as it is considered a non-renewable energy source. The use of hydrogen fuel on-board ships, particularly in modern power plants may contribute to overcoming the above problems. The present paper considers the possibility of the use of hydrogen fuel for marine applications and discusses different stages of hydrogen gas cycle beginning with hydrogen generation process from clean energy until using it as fuel for internal combustion engines on-board one RO/RO ship, named Taba, operating in the Mediterranean Sea. Compared to the diesel engine, the hydrogen fuelled engine is found to be lower in thermal efficiency and fuel consumption, however, some adjustments are needed.

  5. Computational Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Westbrook, C K; Mizobuchi, Y; Poinsot, T J; Smith, P J; Warnatz, J

    2004-08-26

    Progress in the field of computational combustion over the past 50 years is reviewed. Particular attention is given to those classes of models that are common to most system modeling efforts, including fluid dynamics, chemical kinetics, liquid sprays, and turbulent flame models. The developments in combustion modeling are placed into the time-dependent context of the accompanying exponential growth in computer capabilities and Moore's Law. Superimposed on this steady growth, the occasional sudden advances in modeling capabilities are identified and their impacts are discussed. Integration of submodels into system models for spark ignition, diesel and homogeneous charge, compression ignition engines, surface and catalytic combustion, pulse combustion, and detonations are described. Finally, the current state of combustion modeling is illustrated by descriptions of a very large jet lifted 3D turbulent hydrogen flame with direct numerical simulation and 3D large eddy simulations of practical gas burner combustion devices.

  6. An integratable microfluidic cartridge for forensic swab samples lysis.

    Science.gov (United States)

    Yang, Jianing; Brooks, Carla; Estes, Matthew D; Hurth, Cedric M; Zenhausern, Frederic

    2014-01-01

    Fully automated rapid forensic DNA analysis requires integrating several multistep processes onto a single microfluidic platform, including substrate lysis, extraction of DNA from the released lysate solution, multiplexed PCR amplification of STR loci, separation of PCR products by capillary electrophoresis, and analysis for allelic peak calling. Over the past several years, most of the rapid DNA analysis systems developed started with the reference swab sample lysate and involved an off-chip lysis of collected substrates. As a result of advancement in technology and chemistry, addition of a microfluidic module for swab sample lysis has been achieved in a few of the rapid DNA analysis systems. However, recent reports on integrated rapid DNA analysis systems with swab-in and answer-out capability lack any quantitative and qualitative characterization of the swab-in sample lysis module, which is important for downstream forensic sample processing. Maximal collection and subsequent recovery of the biological material from the crime scene is one of the first and critical steps in forensic DNA technology. Herein we present the design, fabrication and characterization of an integratable swab lysis cartridge module and the test results obtained from different types of commonly used forensic swab samples, including buccal, saliva, and blood swab samples, demonstrating the compatibility with different downstream DNA extraction chemistries. This swab lysis cartridge module is easy to operate, compatible with both forensic and microfluidic requirements, and ready to be integrated with our existing automated rapid forensic DNA analysis system. Following the characterization of the swab lysis module, an integrated run from buccal swab sample-in to the microchip CE electropherogram-out was demonstrated on the integrated prototype instrument. Therefore, in this study, we demonstrate that this swab lysis cartridge module is: (1) functionally, comparable with routine benchtop lysis

  7. Continuous plasma perfusion of dual cartridges in series: rationale and early clinical experience.

    Science.gov (United States)

    Sun, Liang; Yan, Peng-Bo; Zhang, Yu-Hua; Wei, Lu-Qing; Li, Guo-Qiang

    2016-12-01

    To improve the efficiency of plasma perfusion on eliminating plasma paraquat (PQ), we designed continuous plasma perfusion of dual cartridges in series (CPPDCS) on Diapact Braun CRRT machine. The goals of this study were to evaluate the effective of CPPDCS on paraquat removal in patients with acute paraquat intoxication. Our results show that the PQ clearance rate of dual cartridges was significantly higher than that of single cartridge at 1st, 2nd, 3(rd), and 4th plasma perfusion. Compared with single-cartridge plasma perfusion, CPPDCS significantly reduced the frequency of cartridge replacement, shorten the time of perfusion. These results indicate that CPPDCS is effective than plasma perfusion of single cartridge on PQ clearance rate and may provide an effective treatment for PQ poisoning.

  8. The effects of laser welding on heterogeneous immunoassay performance in a microfluidic cartridge

    Science.gov (United States)

    Mäntymaa, Anne; Halme, Jussi; Välimaa, Lasse; Kallio, Pasi

    2011-01-01

    Sealing of a microfluidic cartridge is a challenge, because the cartridge commonly contains heat-sensitive biomolecules that must also be protected from contamination. In addition, the objective is usually to obtain a sealing method suitable for mass production. Laser welding is a rapid technique that can be accomplished with low unit costs. Even though the technique has been widely adopted in industry, the literature on its use in microfluidic applications is not large. This paper is the first to report the effects of laser welding on the performance of the heterogeneous immunoassay in a polystyrene microfluidic cartridge in which biomolecules are immobilized into the reaction surface of the cartridge before sealing. The paper compares the immunoassay performance of microfluidic cartridges that are sealed either with an adhesive tape or by use of laser transmission welding. The model analyte used is thyroid stimulating hormone (TSH). The results show that the concentration curves in the laser-welded cartridges are very close to the curves in the taped cartridges. This indicates, first, that laser welding does not cause any significant reduction in immunoassay performance, and second, that the polystyrene cover does not have significant effect on the signal levels. Interestingly, the coefficients of variance between parallel samples were lower in the laser-welded cartridges than in the taped cartridges. PMID:22685505

  9. Tritium release from a nonevaportable getter-pump cartridge exposed to moist air at ambient temperature

    Energy Technology Data Exchange (ETDEWEB)

    Biel, T.J.; Sherwood, A.E.; Singleton, M.F.; Alire, R.M.

    1979-07-10

    The amount of tritium released when a commercially available getter-pump cartridge was exposed to moist air at ambient temperatures was measured. The cartridge consisted of Zr-Al powder pressed onto an iron substrate, which is the type of cartridge proposed for use in the Tokomak Fusion Test Reactor. While the initial release of tritium was rapid the total activity released was lss than 0.005% of the cartridge loading. Of this amount, at least 80% was released as tritiated water. 8 figures.

  10. The Diesel Combustion Collaboratory: Combustion Researchers Collaborating over the Internet

    Energy Technology Data Exchange (ETDEWEB)

    C. M. Pancerella; L. A. Rahn; C. Yang

    2000-02-01

    The Diesel Combustion Collaborator (DCC) is a pilot project to develop and deploy collaborative technologies to combustion researchers distributed throughout the DOE national laboratories, academia, and industry. The result is a problem-solving environment for combustion research. Researchers collaborate over the Internet using DCC tools, which include: a distributed execution management system for running combustion models on widely distributed computers, including supercomputers; web-accessible data archiving capabilities for sharing graphical experimental or modeling data; electronic notebooks and shared workspaces for facilitating collaboration; visualization of combustion data; and video-conferencing and data-conferencing among researchers at remote sites. Security is a key aspect of the collaborative tools. In many cases, the authors have integrated these tools to allow data, including large combustion data sets, to flow seamlessly, for example, from modeling tools to data archives. In this paper the authors describe the work of a larger collaborative effort to design, implement and deploy the DCC.

  11. Rotary Bed Reactor for Chemical-Looping Combustion with Carbon Capture. Part 2: Base Case and Sensitivity Analysis

    KAUST Repository

    Zhao, Zhenlong

    2013-01-17

    Part 1 (10.1021/ef3014103) of this series describes a new rotary reactor for gas-fueled chemical-looping combustion (CLC), in which, a solid wheel with microchannels rotates between the reducing and oxidizing streams. The oxygen carrier (OC) coated on the surfaces of the channels periodically adsorbs oxygen from air and releases it to oxidize the fuel. A one-dimensional model is also developed in part 1 (10.1021/ef3014103). This paper presents the simulation results based on the base-case design parameters. The results indicate that both the fuel conversion efficiency and the carbon separation efficiency are close to unity. Because of the relatively low reduction rate of copper oxide, fuel conversion occurs gradually from the inlet to the exit. A total of 99.9% of the fuel is converted within 75% of the channel, leading to 25% redundant length near the exit, to ensure robustness. In the air sector, the OC is rapidly regenerated while consuming a large amount of oxygen from air. Velocity fluctuations are observed during the transition between sectors because of the complete reactions of OCs. The gas temperature increases monotonically from 823 to 1315 K, which is mainly determined by the solid temperature, whose variations with time are limited within 20 K. The overall energy in the solid phase is balanced between the reaction heat release, conduction, and convective cooling. In the sensitivity analysis, important input parameters are identified and varied around their base-case values. The resulting changes in the model-predicted performance revealed that the most important parameters are the reduction kinetics, the operating pressure, and the feed stream temperatures. © 2012 American Chemical Society.

  12. Modeling of the carbonaceous aerosol. Particular case of the combustion fractal particulates; Modelisation de l'aerosol carbone. Cas particulier des particules fractales de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Bessagnet, B.

    2000-07-01

    Most generally, atmospheric aerosol particles are ideally modelled as spheres for which it is easy to calculate geometrical properties (diameter, surface, and volume) and ensuing radiative, dynamical and chemical characteristics. However, the particles issued in particular from combustion processes display a large range of structures, from linear cluster structures to quasi spherical ones. These various shapes result in quite different physical and chemical characteristics for these particles. Thus, the processes of absorption, coagulation and deposition are strongly affected by the fractal nature of aerosols. Whereas only one discretization parameter (diameter) is required in the spectral distribution of spherical particles, it is necessary to use a 2-D distribution n(v,a) for fractal ones, v and a respectively representing the volume and the surface of the particle. The governing aerosol population balance equation not only involves a coagulation term but also a coalescence contribution describing the surface evolution. With this new model, surface fractal dimensions are associated with varying particle morphologies. This model has been applied to a plume study. First, the gas phase is treated using a gas phase chemistry model, then the fractal aerosol module is used for the particulate phase.

  13. Combustion from basics to applications

    CERN Document Server

    Lackner, Maximilian; Winter, Franz

    2013-01-01

    Combustion, the process of burning, is defined as a chemical reaction between a combustible reactant (the fuel) and an oxidizing agent (such as air) in order to produce heat and in most cases light while new chemical species (e.g., flue gas components) are formed. This book covers a gap on the market by providing a concise introduction to combustion. Most of the other books currently available are targeted towards the experienced users and contain too many details and/or contain knowledge at a fairly high level. This book provides a brief and clear overview of the combustion basics, suitable f

  14. Problematic issues of air protection during thermal processes related to the energetic uses of sewage sludge and other waste. Case study: Co-combustion in peaking power plant.

    Science.gov (United States)

    Hroncová, Emília; Ladomerský, Juraj; Musil, Juraj

    2017-08-19

    Currently, it is necessary to deal with issues related to the emissions as there is a constantly increasing interest in combusting sludge from sewage treatment plants in the boilers for wood. An analysis of the energetic importance of the combustion of sewage sludge has already been carried out, but the effects of various treatments of the sludge are not always clear, e.g. composting and subsequent combustion to the air pollution. Investments in other thermal processes of energetic utilisation of sewage sludge and organic waste are not always successfully implemented. The objective of this paper is to point out some problematic cases for acceptance of thermal processes related to energetic use of waste in terms of the air protection. The other aim is to mention the experience with solutions of such issues in Slovakia. There are mentioned first results of the operational validation experiments during the energy generation in circulating fluidized bed boiler in peaking power plant (Power 110MW) with the addition of the so-called alternative fuel based on wood and sewage sludge to the main fuel - black coal (anthracite). And there has already been achieved the highest share of 12.4%w. (dry matter) of sewage sludge in form of compost in blend with black coal, which is technologically viable. Moreover analyzed the problems of the authorization and operation of the co-combustion of sewage sludge and of combustion of products of various kinds of pyrolysis waste - pyrolysis gas and pyrolysis oil are analyzed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Microfluidic cartridges for automated, point-of-care blood cell counting

    CSIR Research Space (South Africa)

    Smith, Suzanne

    2016-11-01

    Full Text Available cell counting to be performed. The functional steps within the microfluidic cartridge as well as the surrounding instrumentation required to control and test the cartridges in an automated fashion are described. The results recorded from 10 white blood...

  16. Research on rotary forming mechanism of cartridge bottom by FEM

    Institute of Scientific and Technical Information of China (English)

    刘钢; 姚雄亮; 黄少东; 唐全波

    2003-01-01

    The rotary forging of a cartridge bottom is simulated by finite element method with DEFORMTM. The analysis of stress and strain rate results indicates that the deformation conditions and the final geometry of a product are not completely axis-symmetrical under the partial loading conditions during the rotary forging operations. It is therefore required to have a few more rotary forging cycles at the end of total feeding to eliminate nonuniformity. The results of simulation show that the optimization of rotary forging process conditions can be achieved to avoid the underfill defect resulting from improper process conditions. This technology can be used to manufacture ring components with thin bottoms by properly controlling the working process and the tooling motion.

  17. Combustion physics

    Science.gov (United States)

    Jones, A. R.

    1985-11-01

    Over 90% of our energy comes from combustion. By the year 2000 the figure will still be 80%, even allowing for nuclear and alternative energy sources. There are many familiar examples of combustion use, both domestic and industrial. These range from the Bunsen burner to large flares, from small combustion chambers, such as those in car engines, to industrial furnaces for steel manufacture or the generation of megawatts of electricity. There are also fires and explosions. The bountiful energy release from combustion, however, brings its problems, prominent among which are diminishing fuel resources and pollution. Combustion science is directed towards finding ways of improving efficiency and reducing pollution. One may ask, since combustion is a chemical reaction, why physics is involved: the answer is in three parts. First, chemicals cannot react unless they come together. In most flames the fuel and air are initially separate. The chemical reaction in the gas phase is very fast compared with the rate of mixing. Thus, once the fuel and air are mixed the reaction can be considered to occur instantaneously and fluid mechanics limits the rate of burning. Secondly, thermodynamics and heat transfer determine the thermal properties of the combustion products. Heat transfer also plays a role by preheating the reactants and is essential to extracting useful work. Fluid mechanics is relevant if work is to be performed directly, as in a turbine. Finally, physical methods, including electric probes, acoustics, optics, spectroscopy and pyrometry, are used to examine flames. The article is concerned mainly with how physics is used to improve the efficiency of combustion.

  18. Applied combustion

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    From the title, the reader is led to expect a broad practical treatise on combustion and combustion devices. Remarkably, for a book of modest dimension, the author is able to deliver. The text is organized into 12 Chapters, broadly treating three major areas: combustion fundamentals -- introduction (Ch. 1), thermodynamics (Ch. 2), fluid mechanics (Ch. 7), and kinetics (Ch. 8); fuels -- coal, municipal solid waste, and other solid fuels (Ch. 4), liquid (Ch. 5) and gaseous (Ch. 6) fuels; and combustion devices -- fuel cells (Ch. 3), boilers (Ch. 4), Otto (Ch. 10), diesel (Ch. 11), and Wankel (Ch. 10) engines and gas turbines (Ch. 12). Although each topic could warrant a complete text on its own, the author addresses each of these major themes with reasonable thoroughness. Also, the book is well documented with a bibliography, references, a good index, and many helpful tables and appendices. In short, Applied Combustion does admirably fulfill the author`s goal for a wide engineering science introduction to the general subject of combustion.

  19. Evaluation and comparison of a national made dental cartridge with two foreign made

    Directory of Open Access Journals (Sweden)

    Mahmood Hashemi H

    2006-06-01

    Full Text Available Background and Aim: Several factories produce dental cartridge in the world. In Iran, Daroupakhsh company is responsible for this task. The aim of this study was evaluate some properties of daroupakhsh cartridge and compare them with two imported ones: Ecocaine (made in Italy and Septodont (made in France. Materials and Methods: In this experimental study, 70 healthy patients from maxillofacial clinic of Shariaty hospital were selected. After obtaining informed consent, 0.1 cc of each carpule was injected to the patients' frontal region and the extent of anesthesia was measured at different time intervals. Also the quality of injections was evaluated by 11 surgeons. The dimensions of the three cartridges were also measured and compared together. Data were analyzed by repeated measure ANOVA and Friedman with p<0.05 as the limit of significance. Results: There was no significant difference in extent and duration of anesthesia among the studied cartridges. Surgeons were equally satisfied of all three kinds of cartridges. All of the cartridges were aspirable. Conclusion: Based on the results of this study, the three studied cartridges had similar properties.

  20. A new method for antimony speciation in plant biomass and nutrient media using anion exchange cartridge.

    Science.gov (United States)

    Tisarum, Rujira; Ren, Jing-Hua; Dong, Xiaoling; Chen, Hao; Lessl, Jason T; Ma, Lena Q

    2015-11-01

    A selective separation method based on anion exchange cartridge was developed to determine antimony (Sb) speciation in biological matrices by graphite furnace atomic absorption spectrophotometry (GFAAS). The selectivity of the cartridge towards antimonite [Sb(III)] and antimonate [Sb(V)] reversed in the presence of deionized (DI) water and 2mM citric acid. While Sb(V) was retained by the cartridge in DI water, Sb(III) was retained in citric acid media. At pH 6, Sb(III) and Sb(V) formed Sb(III)- and Sb(V)-citrate complexes, but the cartridge had higher affinity towards the Sb(III)-citrate complex. Separation of Sb(III) was tested at various concentrations in fresh and spent growth media and plant tissues. Our results showed that cartridge-based Sb speciation was successful in plant tissues, which was confirmed by HPLC-ICP-MS. The cartridge retained Sb(III) and showed 92-104% Sb(V) recovery from arsenic hyperaccumulator Pteris vittata roots treated with Sb(III) and Sb(V). The cartridge procedure is an effective alternative for Sb speciation, offering low cost, reproducible results, and simple Sb analysis using GFAAS.

  1. Scale-up of Sterilizing-grade Membrane Filters from Discs to Pleated Cartridges: Effects of Operating Parameters and Solution Properties.

    Science.gov (United States)

    Kumar, Anil; Martin, Jerold; Kuriyel, Ralf

    2015-01-01

    For direct flow sterilizing-grade filtration, a linear scale-up between the performance of discs and pleated filter cartridges has traditionally been assumed. Linear scale-up assumes that the filtration performances, defined here as filter flux and capacity, scale linearly with the membrane area and remains independent of the selected device formats. However, experimental results show that the later assumption does not hold in all cases. In this article, we investigated the effect of solution properties and operating parameters on scale-up with both fouling and non-fouling feeds. For non-fouling solutions, such as buffers, the flux ratio, defined as α, between pleated filter cartridges and disc filters range from 0.5 to 0.85. For complex fouling feeds, such as protein or cell culture media solutions, the ratio of initial flux between pleated filter cartridges and discs was the same as the flux ratio, α. For fouling solutions, the ratio of filtration capacity between pleated cartridges and discs, referred to as capacity ratio, β, was variable. We found that β was sensitive to the particle size distribution of the challenge solution and the mode of filtration operation (constant pressure or constant flux), whereas it was less sensitive to the magnitude of the operating pressure or flux and concentration of the fouling species. For most conditions tested, β among pleated cartridges and discs was within ±20% variation of unity. At the end, we present a modified standard model that accounts for both variations in flux ratio, α, as well as capacity ratios, β, for estimating the requirement for membrane area at manufacturing scale with proteinacious fouling and non-protein/non-fouling feeds. The data show that for cases where filtration is capacity controlled, flux ratios between the pleated filter and disc are not critical. For such cases, the use of a high-area laid-over pleated cartridge construction allows for reducing the number of 10 inch pleated filter

  2. Residential proximity to industrial combustion facilities and risk of non-Hodgkin lymphoma: A case-control study

    NARCIS (Netherlands)

    Pronk, A.; Nuckols, J.R.; Roos, A.J. de; Airola, M.; Colt, J.S.; Cerhan, J.R.; Morton, L.; Cozen, W.; Severson, R.; Blair, A.; Cleverly, D.; Ward, M.H.

    2013-01-01

    Background: Residence near municipal solid waste incinerators, a major historical source of dioxin emissions, has been associated with increased risk of non-Hodgkin lymphoma (NHL) in European studies. The aim of our study was to evaluate residence near industrial combustion facilities and estimates

  3. Residential proximity to industrial combustion facilities and risk of non-Hodgkin lymphoma: A case-control study

    NARCIS (Netherlands)

    Pronk, A.; Nuckols, J.R.; Roos, A.J. de; Airola, M.; Colt, J.S.; Cerhan, J.R.; Morton, L.; Cozen, W.; Severson, R.; Blair, A.; Cleverly, D.; Ward, M.H.

    2013-01-01

    Background: Residence near municipal solid waste incinerators, a major historical source of dioxin emissions, has been associated with increased risk of non-Hodgkin lymphoma (NHL) in European studies. The aim of our study was to evaluate residence near industrial combustion facilities and estimates

  4. Biofuels combustion.

    Science.gov (United States)

    Westbrook, Charles K

    2013-01-01

    This review describes major features of current research in renewable fuels derived from plants and from fatty acids. Recent and ongoing fundamental studies of biofuel molecular structure, oxidation reactions, and biofuel chemical properties are reviewed, in addition to combustion applications of biofuels in the major types of engines in which biofuels are used. Biofuels and their combustion are compared with combustion features of conventional petroleum-based fuels. Two main classes of biofuels are described, those consisting of small, primarily alcohol, fuels (particularly ethanol, n-butanol, and iso-pentanol) that are used primarily to replace or supplement gasoline and those derived from fatty acids and used primarily to replace or supplement conventional diesel fuels. Research efforts on so-called second- and third-generation biofuels are discussed briefly.

  5. Turbulent combustion

    Energy Technology Data Exchange (ETDEWEB)

    Talbot, L.; Cheng, R.K. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    Turbulent combustion is the dominant process in heat and power generating systems. Its most significant aspect is to enhance the burning rate and volumetric power density. Turbulent mixing, however, also influences the chemical rates and has a direct effect on the formation of pollutants, flame ignition and extinction. Therefore, research and development of modern combustion systems for power generation, waste incineration and material synthesis must rely on a fundamental understanding of the physical effect of turbulence on combustion to develop theoretical models that can be used as design tools. The overall objective of this program is to investigate, primarily experimentally, the interaction and coupling between turbulence and combustion. These processes are complex and are characterized by scalar and velocity fluctuations with time and length scales spanning several orders of magnitude. They are also influenced by the so-called {open_quotes}field{close_quotes} effects associated with the characteristics of the flow and burner geometries. The authors` approach is to gain a fundamental understanding by investigating idealized laboratory flames. Laboratory flames are amenable to detailed interrogation by laser diagnostics and their flow geometries are chosen to simplify numerical modeling and simulations and to facilitate comparison between experiments and theory.

  6. 42 CFR 84.1157 - Chemical cartridge respirators with particulate filters; performance requirements; general.

    Science.gov (United States)

    2010-10-01

    ... APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Dust, Fume, and Mist; Pesticide; Paint Spray; Powered Air... following minimum requirements for performance and protection: (a) Breathing resistance test. (1) Resistance...) The maximum allowable resistance requirements for chemical cartridge respirators are as...

  7. Nanoparticle separation with a miniaturized asymmetrical flow field-flow fractionation cartridge

    Directory of Open Access Journals (Sweden)

    David eMüller

    2015-07-01

    Full Text Available Asymmetrical Flow Field-Flow Fractionation (AF4 is a separation technique applicable to particles over a wide size range. Despite the many advantages of AF4, its adoption in routine particle analysis is somewhat limited by the large footprint of currently available separation cartridges, extended analysis times and significant solvent consumption. To address these issues, we describe the fabrication and characterization of miniaturized AF4 cartridges. Key features of the scale-down platform include simplified cartridge and reagent handling, reduced analysis costs and higher throughput capacities. The separation performance of the miniaturized cartridge is assessed using certified gold and silver nanoparticle standards. Analysis of gold nanoparticle populations indicates shorter analysis times and increased sensitivity compared to conventional AF4 separation schemes. Moreover, nanoparticulate titanium dioxide populations exhibiting broad size distributions are analyzed in a rapid and efficient manner. Finally, the repeatability and reproducibility of the miniaturized platform are investigated with respect to analysis time and separation efficiency.

  8. Evaluation and comparison of a national made dental cartridge with two foreign made

    OpenAIRE

    2006-01-01

    Background and Aim: Several factories produce dental cartridge in the world. In Iran, Daroupakhsh company is responsible for this task. The aim of this study was evaluate some properties of daroupakhsh cartridge and compare them with two imported ones: Ecocaine (made in Italy) and Septodont (made in France). Materials and Methods: In this experimental study, 70 healthy patients from maxillofacial clinic of Shariaty hospital were selected. After obtaining informed consent, 0.1 cc of each carpu...

  9. The indicating FTA elute cartridge a solid sample carrier to detect high-risk HPV and high-grade cervical lesions

    NARCIS (Netherlands)

    Bie, R.P. de; Schmeink, C.E.; Bakkers, J.M.J.E.; Snijders, P.J.L.M.; Quint, W.G.V.; Massuger, L.F.A.G.; Bekkers, R.L.M.; Melchers, W.J.G.

    2011-01-01

    The clinically validated high-risk human papillomavirus (hrHPV) Hybrid Capture 2 (HC2) and GP5+/6+-PCR assays were analyzed on an Indicating FTA Elute cartridge (FTA cartridge). The FTA cartridge is a solid dry carrier that allows safe transport of cervical samples. FTA cartridge samples were

  10. Aliança estratégica no canal de marketing: o caso ALE Combustíveis S.A. Strategic alliance in the marketing channel: the Ale Combustíveis S.A. case

    Directory of Open Access Journals (Sweden)

    Carlos Eduardo Garcia Cotta

    2010-01-01

    Full Text Available O artigo analisa a estratégia utilizada pela ALE Combustíveis em uma operação desenhada para vender lubrificantes automotivos em sua rede de postos. O estudo avalia as alianças efetuadas com a Elf e posteriormente com a AC Delco, revelando as motivações, escolha dos parceiros, desenho do modelo de relacionamento, gestão das alianças e avaliação do modelo adotado, confrontando a experiência prática com as prescrições da literatura. O modelo adotado, denominado broker, caracteriza-se pela preservação da autonomia das marcas, com a ALE aportando sua estrutura e força de vendas, e o parceiro, a logística de reabastecimento e processamento de pedidos. O método do caso foi adotado como estratégia de pesquisa e o relato revela o acerto na escolha do modelo, porém falhas estratégicas na capacidade operacional e posicionamento do produto, na aliança com a Elf, e na relação de forças no canal, na aliança com a AC Delco, conduziram ao fracasso de ambas as tentativas.This paper analyses the strategy adopted by ALE Combustíveis, a Brazilian Company, in an operation designed to sell automotive lubricants at gas stations. This study reviews the alliances made with Elf and later with AC Delco, exposing ALE's motivations, partner selection, design of relationship model, alliance management and assessment of adopted model, confronting practical experience with prescriptions in the published literature. The model, named broker, is characterized by preservation of the brand's autonomy, with ALE contributing its structure and sales force, and its partner, in turn, the fuelling logistics and order processing. The case method was adopted as a research strategy and this report shows how successful the model selection proved, as well as the strategic blunders related to the operational capacity and product positioning, in the alliance with Elf, and in the forces of management interrelations within the channel, in the AC Delco alliance case

  11. Advanced Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R. [NETL

    2013-03-11

    The activity reported in this presentation is to provide the mechanical and physical property information needed to allow rational design, development and/or choice of alloys, manufacturing approaches, and environmental exposure and component life models to enable oxy-fuel combustion boilers to operate at Ultra-Supercritical (up to 650{degrees}C & between 22-30 MPa) and/or Advanced Ultra-Supercritical conditions (760{degrees}C & 35 MPa).

  12. On the causal links between health indicator, output, combustible renewables and waste consumption, rail transport, and CO2 emissions: the case of Tunisia.

    Science.gov (United States)

    Ben Jebli, Mehdi

    2016-08-01

    This study employs the autoregressive distributed lag (ARDL) approach and Granger causality test to investigate the short- and long-run relationships between health indicator, real GDP, combustible renewables and waste consumption, rail transport, and carbon dioxide (CO2) emissions for the case of Tunisia, spanning the period of 1990-2011. The empirical findings suggest that the Fisher statistic of the Wald test confirm the existence of a long-run relationship between the variables. Moreover, the long-run estimated elasticities of the ARDL model provide that output and combustible renewables and waste consumption have a positive and statistically significant impact on health situation, while CO2 emissions and rail transport both contribute to the decrease of health indicator. Granger causality results affirm that, in the short-run, there is a unidirectional causality running from real GDP to health, a unidirectional causality from health to combustible renewables and waste consumption, and a unidirectional causality from all variables to CO2 emissions. In the long-run, all the computed error correction terms are significant and confirm the existence of long-run association among the variables. Our recommendations for the Tunisian policymakers are as follows: (i) exploiting wastes and renewable fuels can be a good strategy to eliminate pollution caused by emissions and subsequently improve health quality, (ii) the use of renewable energy as a main source for national rail transport is an effective strategy for public health, (iii) renewable energy investment projects are beneficial plans for the country as this contributes to the growth of its own economy and reduce energy dependence, and (iii) more renewable energy consumption leads not only to decrease pollution but also to stimulate health situation because of the increase of doctors and nurses numbers.

  13. Investigating Premature Ignition of Thruster Pressure Cartridges by Mechanical Impact of Internal Components

    Science.gov (United States)

    Woods, Stephen S.; Saulsberry, Regor

    2010-01-01

    Pyrotechnic thruster pressure cartridges (TPCs) are used for aeroshell separation on a new NASA crew launch vehicle. The premature ignition concern was hypothesized based on the potential range of motion of the subassemblies, projected worst case accelerations, and the internal geometry that could subject propellant grains to mechanical impact sufficiently high for ignition. This possibility was investigated by fabricating a high-fidelity model of the suspected contact geometry, placing a representative amount of propellant in it, and impacting the propellant with a range of forces equivalent to and greater than the maximum possible during launch. Testing demonstrated that the likelihood of ignition is less than 1 in 1,000,000. The test apparatus, methodology, and results are described in this paper. Nondestructive evaluation ( NDE) during TPC acceptance testing indicated that internal assemblies moved during shock and vibration testing due to an internal bond anomaly. This caused concerns that the launch environment might produce the same movement and release propellant grains that might be prematurely ignited through impact or through electrostatic discharge (ESD) as grains vibrated against internal surfaces. Since a new lot could not be fabricated in time, a determination had to be made as to whether the lot was acceptable to fly. This paper discusses the analysis and impact testing used to address the potential impact issue and a separate paper addresses the ESD issue.

  14. RAMGEN ROTOR CARTRIDGE FOR THE PRE-PROTOTYPE RAMGEN ENGINE

    Energy Technology Data Exchange (ETDEWEB)

    Aaron Koopman

    2003-09-01

    The research and development of a unique combustion engine is presented. The engine converts the thrust from ramjet modules located on the rim of a disk into shaft torque, which in turn can be used for electrical power generation or mechanical drive applications. A test program was undertaken that included evaluation of the pre-prototype engine and incorporation of improvements to the thrust modules and supporting systems. Fuel mixing studies with vortex generators and bluff body flame holders demonstrated the importance of increasing the shear-layer area and spreading angle to augment flame volume. Evaluation of flame-holding configurations (with variable fuel injection methods) concluded that the heat release zone, and therefore combustion efficiency, could be manipulated by judicious selection of bluff body geometry, and is less influenced by fuel injection distribution. Finally, successful operation of novel fuel and cooling air delivery systems have resolved issues of gas (fuel and air) delivery to the individual rotor segments. The lessons learned from the pre-prototype engine are currently being applied to the development of a 2.8MW engine.

  15. Filtration combustion: Smoldering and SHS

    Science.gov (United States)

    Matkowsky, Bernard J.

    1995-01-01

    Smolder waves and SHS (self-propagating high-temperature synthesis) waves are both examples of combustion waves propagating in porous media. When delivery of reactants through the pores to the reaction site is an important aspect of the process, it is referred to as filtration combustion. The two types of filtration combustion have a similar mathematical formulation, describing the ignition, propagation and extinction of combustion waves in porous media. The goal in each case, however, is different. In smoldering the desired goal is to prevent propagation, whereas in SHS the goal is to insure propagation of the combustion wave, leading to the synthesis of desired products. In addition, the scales in the two areas of application may well differ. For example, smoldering generally occurs at a relatively low temperature and with a smaller propagation velocity than SHS filtration combustion waves. Nevertheless, the two areas of application have much in common, so that mechanisms learned about in one application can be used to advantage in the other. In this paper we discuss recent results in the areas of filtration combustion.

  16. A cartridge based sensor array platform for multiple coagulation measurements from plasma.

    Science.gov (United States)

    Cakmak, O; Ermek, E; Kilinc, N; Bulut, S; Baris, I; Kavakli, I H; Yaralioglu, G G; Urey, Hakan

    2015-01-07

    This paper proposes a MEMS-based sensor array enabling multiple clot-time tests for plasma in one disposable microfluidic cartridge. The versatile LoC (Lab-on-Chip) platform technology is demonstrated here for real-time coagulation tests (activated Partial Thromboplastin Time (aPTT) and Prothrombin Time (PT)). The system has a reader unit and a disposable cartridge. The reader has no electrical connections to the cartridge. This enables simple and low-cost cartridge designs and avoids reliability problems associated with electrical connections. The cartridge consists of microfluidic channels and MEMS microcantilevers placed in each channel. The microcantilevers are made of electroplated nickel. They are actuated remotely using an external electro-coil and the read-out is also conducted remotely using a laser. The phase difference between the cantilever oscillation and the coil drive is monitored in real time. During coagulation, the viscosity of the blood plasma increases resulting in a change in the phase read-out. The proposed assay was tested on human and control plasma samples for PT and aPTT measurements. PT and aPTT measurements from control plasma samples are comparable with the manufacturer's datasheet and the commercial reference device. The measurement system has an overall 7.28% and 6.33% CV for PT and aPTT, respectively. For further implementation, the microfluidic channels of the cartridge were functionalized for PT and aPTT tests by drying specific reagents in each channel. Since simultaneous PT and aPTT measurements are needed in order to properly evaluate the coagulation system, one of the most prominent features of the proposed assay is enabling parallel measurement of different coagulation parameters. Additionally, the design of the cartridge and the read-out system as well as the obtained reproducible results with 10 μl of the plasma samples suggest an opportunity for a possible point-of-care application.

  17. Effect of co-combustion on the burnout of lignite/biomass blends: A Turkish case study

    Energy Technology Data Exchange (ETDEWEB)

    Haykirl-Acma, H.; Yaman, S. [Istanbul Technical University, Istanbul (Turkey)

    2008-11-15

    Co-combustion of Turkish Elbistan lignite and woody shells of hazelnut was performed in a TGA tip to 1173 K with a heating rate of 20 K/min. SEM images of each fuel revealed the differences in their physical appearances. Hazelnut shell was blended with lignite in the range of 2-20 wt% to observe the co-combustion properties. Maximum burning rates (R{sub max}), temperatures of the maximum burning rates (TR{sub max}), and the final burnout values of the parent samples and the blends were compared. The results were interpreted considering lignite properties and the major biomass ingredients such as cellulosics, hemicellulosics, and lignin. Deviations between the theoretical and experimental burnout values were evaluated at various temperatures. Burnout characteristics of the blends up to 10 wt% were concluded to have a synergistic effect so the addition of hazelnut shell up to 8 wt% provided higher burnouts than the expected theoretical ones, whereas addition of as much as 10 wt% led to a decrease in the burnout. However, the additive effects were more favorable for the blend having a biomass content of 20 wt%. Apparent activation energy, R{sub max} and TR{sub max}, were found to follow the additive behavior for the blend samples.

  18. Investigating Premature Ignition of Thruster Pressure Cartridges by Vibration-Induced Electrostatic Discharge

    Science.gov (United States)

    Woods, Stephen S.; Saulsberry, Regor

    2010-01-01

    Pyrotechnic thruster pressure cartridges (TPCs) are used for aeroshell separation on a new NASA crew launch vehicle. Nondestructive evaluation (NDE) during TPC acceptance testing indicated that internal assemblies moved during shock and vibration testing due to an internal bond anomaly. This caused concerns that the launch environment might produce the same movement and release propellant grains that might be prematurely ignited through impact or through electrostatic discharge (ESD) as grains vibrated against internal surfaces. Since a new lot could not be fabricated in time, a determination had to be made as to whether the lot was acceptable to fly. This paper discusses the ESD evaluation and a separate paper addresses the impact problem. A challenge to straight forward assessment existed due to the unavailability of triboelectric data characterizing the static charging characteristics of the propellants within the TPC. The approach examined the physical limitations for charge buildup within the TPC system geometry and evaluated it for discharge under simulated vibrations used to qualify components for launch. A facsimile TPC was fabricated using SS 301 for the case and surrogate worst case materials for the propellants based on triboelectric data. System discharge behavior was evaluated by applying high voltage to the point of discharge in air and by placing worst case charge accumulations within the facsimile TPC and forcing discharge. The facsimile TPC contained simulated propellant grains and lycopodium, a well characterized indicator for static discharge in dust explosions, and was subjected to accelerations equivalent to the maximum accelerations possible during launch. The magnitude of charge generated within the facsimile TPC system was demonstrated to lie in a range of 100 to 10,000 times smaller than the spark energies measured to ignite propellant grains in industry standard discharge tests. The test apparatus, methodology, and results are described in

  19. 3D-printed paper spray ionization cartridge with fast wetting and continuous solvent supply features.

    Science.gov (United States)

    Salentijn, Gert I J; Permentier, Hjalmar P; Verpoorte, Elisabeth

    2014-12-02

    We report the development of a 3D-printed cartridge for paper spray ionization (PSI) that can be used almost immediately after solvent introduction in a dedicated reservoir and allows prolonged spray generation from a paper tip. The fast wetting feature described in this work is based on capillary action through paper and movement of fluid between paper and the cartridge material (polylactic acid, PLA). The influence of solvent composition, PLA conditioning of the cartridge with isopropanol, and solvent volume introduced into the reservoir have been investigated with relation to wetting time and the amount of solvent consumed for wetting. Spray has been demonstrated with this cartridge for tens of minutes, without any external pumping. It is shown that fast wetting and spray generation can easily be achieved using a number of solvent mixtures commonly used for PSI. The PSI cartridge was applied to the analysis of lidocaine from a paper tip using different solvent mixtures, and to the analysis of lidocaine from a serum sample. Finally, a demonstration of online paper chromatography-mass spectrometry is given.

  20. Combustion Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Combustion Research Laboratory facilitates the development of new combustion systems or improves the operation of existing systems to meet the Army's mission for...

  1. High Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL's High-Pressure Combustion Research Facility in Morgantown, WV, researchers can investigate new high-pressure, high-temperature hydrogen turbine combustion...

  2. The two-fire, one-cartridge stapling method using a modified Endo-GIA.

    Science.gov (United States)

    Yamaguchi, A; Tsuchida, M

    1996-08-01

    The endoscopic stapler (Endo-GIA) was designed to divide tissue between two triple-stapled lines. The endoscopic surgeon frequently encounters situations where only stapling is required. Kirby described a staple closure method that uses a knifeless Endo-GIA cartridge. This method, although useful, has the problem of the modified Endo-GIA unit locking. Therefore, we devised a new technique for endoscopic stapling that involves two consecutive staplings using one cartridge without cutting. This method requires modification of the Endo-GIA system by removing the safety-lock system. In addition to enabling endoscopic stapling techniques without the risk of locking, the method can effect a significant cost savings.

  3. Combustion chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    This research is concerned with the development and use of sensitivity analysis tools to probe the response of dependent variables to model input variables. Sensitivity analysis is important at all levels of combustion modeling. This group`s research continues to be focused on elucidating the interrelationship between features in the underlying potential energy surface (obtained from ab initio quantum chemistry calculations) and their responses in the quantum dynamics, e.g., reactive transition probabilities, cross sections, and thermal rate coefficients. The goals of this research are: (i) to provide feedback information to quantum chemists in their potential surface refinement efforts, and (ii) to gain a better understanding of how various regions in the potential influence the dynamics. These investigations are carried out with the methodology of quantum functional sensitivity analysis (QFSA).

  4. Environmental impacts of varying electric vehicle user behaviours and comparisons to internal combustion engine vehicle usage - An Irish case study

    Science.gov (United States)

    Weldon, Peter; Morrissey, Patrick; O'Mahony, Margaret

    2016-07-01

    Concerns have been expressed regarding the displacement of harmful emissions from internal combustion engine vehicle (ICEV) tailpipes to the sources of electricity generation used to charge electric vehicles (EV). The degree to which EVs can reduce the environmental impacts of road transportation is dependent on the fuel mix of electricity generation within a country and on the real-time charging behaviours of EV users since the fuel mix of electricity generation frequently changes. This paper analyses the varying environmental impacts of EVs based on contrasting user behaviours and compares them to the environmental impacts of ICEVs. Individual EV user profiles are developed which comprise real data emerging from charge events undertaken in Ireland, and information is gathered on the actual CO2 intensity of the electrical grid in real-time, allowing for the carbon intensity of every individual charge event to be determined using time and date information. The results show that the environmental impacts of EVs are highly influenced by the charging behaviours of individual users, and night-time charging was found to produce the largest environmental impact. EVs are shown to be a more environmentally friendly choice of vehicle than ICEVs under a wide majority of scenarios.

  5. Study of the aerobic contamination of four disposable materials (anesthetic cartridge, saliva ejector tip, gutta percha and cotton roll

    Directory of Open Access Journals (Sweden)

    Ashofteh Yazdi K.

    2005-06-01

    Full Text Available Statement of Problem: Today, cross infection control is an integral part of dentistry and many dental health care workers no longer question its necessity. All dental equipments and instruments could be potentially considered as a source of infection. Purpose: The aim of this study was the evaluation of aerobic contaminations of four disposable materials used in routine dental practice. Materials and Methods: In this cross-sectional study, random sampling was performed and tryptone soy broth transfer culture medium was used. After 24 hours of incubation, samples were transferred to specific culture media. (Mckangy, Chocolate agar and Blood agar. Cultured bacteria were stained and studied using gram staining method. The study was carried out in a 17 weeks period. Results: All suction tips were infected with Bacillus cereus bacterium. Two cases of cotton roll samples showed contamination with Bacillus cereus, 2 cases with gram positive, coagulase negative cocci, 1 case with Streptococcus viridians and one case with Enterobacter class A. One case of anesthetic cartridges was contaminated with Staphylococcus epidermidis and two cases with Streptococcus viridians. Two cases of gutta-percha samples were contaminated with Bacillus cereus. Conclusion: Based of the findings of this study, the highest level of contamination was observed in saliva ejector tips. Contamination with Bacillus cereus was seen more frequently.

  6. Oxygen-enhanced combustion

    CERN Document Server

    Baukal, Charles E

    2013-01-01

    Combustion technology has traditionally been dominated by air/fuel combustion. However, two developments have increased the significance of oxygen-enhanced combustion-new technologies that produce oxygen less expensively and the increased importance of environmental regulations. Advantages of oxygen-enhanced combustion include less pollutant emissions as well as increased energy efficiency and productivity. Oxygen-Enhanced Combustion, Second Edition compiles information about using oxygen to enhance industrial heating and melting processes. It integrates fundamental principles, applications, a

  7. 3D-printed paper spray ionization cartridge with fast wetting and continuous solvent supply features

    NARCIS (Netherlands)

    Salentijn, Gert I J; Permentier, Hjalmar P; Verpoorte, Elisabeth

    2014-01-01

    We report the development of a 3D-printed cartridge for paper spray ionization (PSI) that can be used almost immediately after solvent introduction in a dedicated reservoir and allows prolonged spray generation from a paper tip. The fast wetting feature described in this work is based on capillary a

  8. CONCENTRATION AND PROCESSING OF WATERBORNE VIRUSES BY POSITIVE CHARGE 1MDS CARTRIDGE FILTERS AND ORGANIC FLOCCULATION

    Science.gov (United States)

    This chapter describes the most widely used virus adsorption-elution (VIRADEL) method for recovering human enteric viruses from water matrices (Fout et al., 1996). The method takes advantage of postively charged cartridge filters to concentrate viruses from water. The major adv...

  9. Demonstration of Metastable Intermolecular Composites (MIC) on Small Caliber Cartridges and CAD/PAD Percussion Primers

    Science.gov (United States)

    2009-07-01

    of the output charge. In fact, the improved ignition pushed ten of the MIC-primed cartridges over the high pressure limit, whereas, only two of the...nls (lat) uso OOiy) Box Label lnfomalion wee FIP #41 Machine# 18 Date fl/19/2007 Caliber 5.56 Ammo Lot# BLH07D12().005 - -- Bullet Mfg Siorra Gr. Wt

  10. Small-Caliber Ammunition Identification Guide. Volume 1. Small-Arms Cartridges Up to 15 mm

    Science.gov (United States)

    1978-06-01

    strands. In 1914, - : ... . the bullet shape was changed to a long, pointed, jacketed bullet with ant aluminum (or fiber) nose 1,,: filler ahead of the...KINGDOM ROMANIA "Made at R.O.F. plant at On 7.6209-mm cartridges. Woolwich, London. 1963-1969. 񓞰-1949. Sec Note 3. .𔃻’.~ A•SO A356 O UNITUD

  11. Emission factors for PM2.5, CO, CO2, NOx, SO2 and particle size distributions from the combustion of wood species using a new controlled combustion chamber 3CE.

    Science.gov (United States)

    Cereceda-Balic, Francisco; Toledo, Mario; Vidal, Victor; Guerrero, Fabian; Diaz-Robles, Luis A; Petit-Breuilh, Ximena; Lapuerta, Magin

    2017-04-15

    The objective of this research was to determine emission factors (EF) for particulate matter (PM2.5), combustion gases and particle size distribution generated by the combustion of Eucalyptus globulus (EG), Nothofagus obliqua (NO), both hardwoods, and Pinus radiata (PR), softwood, using a controlled combustion chamber (3CE). Additionally, the contribution of the different emissions stages associated with the combustion of these wood samples was also determined. Combustion experiments were performed using shaving size dried wood (0% humidity). The emission samples were collected with a tedlar bag and sampling cartridges containing quartz fiber filters. High reproducibility was achieved between experiment repetitions (CVcombustion smoldering have also very significant contributions. This demonstrates that particle concentrations measured only in stationary state during flame stage may cause underestimation of emissions. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Development of a Paper Spray Mass Spectrometry Cartridge with Integrated Solid Phase Extraction for Bioanalysis.

    Science.gov (United States)

    Zhang, Chengsen; Manicke, Nicholas E

    2015-06-16

    A novel paper spray cartridge with an integrated solid phase extraction (SPE) column is described. The cartridge performs extraction and pre-concentration, as well as sample ionization by paper spray, from complex samples such as plasma. The cartridge allows for selective enrichment of target molecules from larger sample volumes and removal of the matrix, which significantly improved the signal intensity of target compounds in plasma samples by paper spray ionization. Detection limits, quantitative performance, recovery, ionization suppression, and the effects of sample volume were evaluated for five drugs: carbamazepine, atenolol, sulfamethazine, diazepam, and alprazolam. Compared with direct paper spray analysis of dried plasma spots, paper spray analysis using the integrated solid phase extraction improved the detection limits significantly by a factor of 14-70, depending on the drug. The improvement in detection limits was, in large part, due to the capability of analyzing larger sample volumes. In addition, ionization suppression was found to be lower and recovery was higher for paper spray with integrated SPE, as compared to direct paper spray analysis. By spiking an isotopically labeled internal standard into the plasma sample, a linear calibration curve for the drugs was obtained from the limit of detection (LOD) to 1 μg/mL, indicating that this method can be used for quantitative analysis. The paper spray cartridge with integrated SPE could prove valuable for analytes that ionize poorly, in applications where lower detection limits are required, or on portable mass spectrometers. The improved performance comes at the cost of requiring a more complex paper spray cartridge and requiring larger sample volumes than those used in typical direct paper spray ionization.

  13. Combustion 2000

    Energy Technology Data Exchange (ETDEWEB)

    A. Levasseur; S. Goodstine; J. Ruby; M. Nawaz; C. Senior; F. Robson; S. Lehman; W. Blecher; W. Fugard; A. Rao; A. Sarofim; P. Smith; D. Pershing; E. Eddings; M. Cremer; J. Hurley; G. Weber; M. Jones; M. Collings; D. Hajicek; A. Henderson; P. Klevan; D. Seery; B. Knight; R. Lessard; J. Sangiovanni; A. Dennis; C. Bird; W. Sutton; N. Bornstein; F. Cogswell; C. Randino; S. Gale; Mike Heap

    2001-06-30

    . To achieve these objectives requires a change from complete reliance of coal-fired systems on steam turbines (Rankine cycles) and moving forward to a combined cycle utilizing gas turbines (Brayton cycles) which offer the possibility of significantly greater efficiency. This is because gas turbine cycles operate at temperatures well beyond current steam cycles, allowing the working fluid (air) temperature to more closely approach that of the major energy source, the combustion of coal. In fact, a good figure of merit for a HIPPS design is just how much of the enthalpy from coal combustion is used by the gas turbine. The efficiency of a power cycle varies directly with the temperature of the working fluid and for contemporary gas turbines the optimal turbine inlet temperature is in the range of 2300-2500 F (1260-1371 C). These temperatures are beyond the working range of currently available alloys and are also in the range of the ash fusion temperature of most coals. These two sets of physical properties combine to produce the major engineering challenges for a HIPPS design. The UTRC team developed a design hierarchy to impose more rigor in our approach. Once the size of the plant had been determined by the choice of gas turbine and the matching steam turbine, the design process of the High Temperature Advanced Furnace (HITAF) moved ineluctably to a down-fired, slagging configuration. This design was based on two air heaters: one a high temperature slagging Radiative Air Heater (RAH) and a lower temperature, dry ash Convective Air Heater (CAH). The specific details of the air heaters are arrived at by an iterative sequence in the following order:-Starting from the overall Cycle requirements which set the limits for the combustion and heat transfer analysis-The available enthalpy determined the range of materials, ceramics or alloys, which could tolerate the temperatures-Structural Analysis of the designs proved to be the major limitation-Finally the commercialization

  14. Combustion 2000

    Energy Technology Data Exchange (ETDEWEB)

    A. Levasseur; S. Goodstine; J. Ruby; M. Nawaz; C. Senior; F. Robson; S. Lehman; W. Blecher; W. Fugard; A. Rao; A. Sarofim; P. Smith; D. Pershing; E. Eddings; M. Cremer; J. Hurley; G. Weber; M. Jones; M. Collings; D. Hajicek; A. Henderson; P. Klevan; D. Seery; B. Knight; R. Lessard; J. Sangiovanni; A. Dennis; C. Bird; W. Sutton; N. Bornstein; F. Cogswell; C. Randino; S. Gale; Mike Heap

    2001-06-30

    . To achieve these objectives requires a change from complete reliance of coal-fired systems on steam turbines (Rankine cycles) and moving forward to a combined cycle utilizing gas turbines (Brayton cycles) which offer the possibility of significantly greater efficiency. This is because gas turbine cycles operate at temperatures well beyond current steam cycles, allowing the working fluid (air) temperature to more closely approach that of the major energy source, the combustion of coal. In fact, a good figure of merit for a HIPPS design is just how much of the enthalpy from coal combustion is used by the gas turbine. The efficiency of a power cycle varies directly with the temperature of the working fluid and for contemporary gas turbines the optimal turbine inlet temperature is in the range of 2300-2500 F (1260-1371 C). These temperatures are beyond the working range of currently available alloys and are also in the range of the ash fusion temperature of most coals. These two sets of physical properties combine to produce the major engineering challenges for a HIPPS design. The UTRC team developed a design hierarchy to impose more rigor in our approach. Once the size of the plant had been determined by the choice of gas turbine and the matching steam turbine, the design process of the High Temperature Advanced Furnace (HITAF) moved ineluctably to a down-fired, slagging configuration. This design was based on two air heaters: one a high temperature slagging Radiative Air Heater (RAH) and a lower temperature, dry ash Convective Air Heater (CAH). The specific details of the air heaters are arrived at by an iterative sequence in the following order:-Starting from the overall Cycle requirements which set the limits for the combustion and heat transfer analysis-The available enthalpy determined the range of materials, ceramics or alloys, which could tolerate the temperatures-Structural Analysis of the designs proved to be the major limitation-Finally the commercialization

  15. INTEROCC case-control study: lack of association between glioma tumors and occupational exposure to selected combustion products, dusts and other chemical agents.

    Science.gov (United States)

    Lacourt, Aude; Cardis, Elisabeth; Pintos, Javier; Richardson, Lesley; Kincl, Laurel; Benke, Geza; Fleming, Sarah; Hours, Martine; Krewski, Daniel; McLean, Dave; Parent, Marie-Elise; Sadetzki, Siegal; Schlaefer, Klaus; Schlehofer, Brigitte; Lavoue, Jerome; van Tongeren, Martie; Siemiatycki, Jack

    2013-04-12

    The aim was to investigate possible associations between glioma (an aggressive type of brain cancer) and occupational exposure to selected agents: combustion products (diesel and gasoline exhaust emissions, benzo(a)pyrene), dusts (animal dust, asbestos, crystalline silica, wood dust) and some other chemical agents (formaldehyde, oil mist, sulphur dioxide). The INTEROCC study included cases diagnosed with glioma during 2000-2004 in sub-regions of seven countries. Population controls, selected from various sampling frames in different centers, were frequency or individually matched to cases by sex, age and center. Face-to-face interviews with the subject or a proxy respondent were conducted by trained interviewers. Detailed information was collected on socio-economic and lifestyle characteristics, medical history and work history. Occupational exposure to the 10 selected agents was assessed by a job exposure matrix (JEM) which provides estimates of the probability and level of exposure for different occupations. Using a 25% probability of exposure in a given occupation in the JEM as the threshold for considering a worker exposed, the lifetime prevalence of exposure varied from about 1% to about 15% for the different agents. Associations between glioma and each of the 10 agents were estimated by conditional logistic regression, and using three separate exposure indices: i) ever vs. never; ii) lifetime cumulative exposure; iii) total duration of exposure. The study sample consisted of 1,800 glioma cases and 5,160 controls. Most odds ratio estimates were close to the null value. None of the ten agents displayed a significantly increased odds ratio nor any indication of dose-response relationships with cumulative exposure or with duration of exposure. Thus, there was no evidence that these exposures influence risk of glioma.

  16. The application of profluorescent nitroxides to detect reactive oxygen species derived from combustion-generated particulate matter: Cigarette smoke - A case study

    Science.gov (United States)

    Miljevic, B.; Fairfull-Smith, K. E.; Bottle, S. E.; Ristovski, Z. D.

    2010-06-01

    Reactive oxygen species (ROS) and related free radicals are considered to be key factors underpinning the various adverse health effects associated with exposure to ambient particulate matter. Therefore, measurement of ROS is a crucial factor for assessing the potential toxicity of particles. In this work, a novel profluorescent nitroxide, BPEAnit, was investigated as a probe for detecting particle-derived ROS. BPEAnit has a very low fluorescence emission due to inherent quenching by the nitroxide group, but upon radical trapping or redox activity, a strong fluorescence is observed. BPEAnit was tested for detection of ROS present in mainstream and sidestream cigarette smoke. In the case of mainstream cigarette smoke, there was a linear increase in fluorescence intensity with an increasing number of cigarette puffs, equivalent to an average of 101 nmol ROS per cigarette based on the number of moles of the probe reacted. Sidestream cigarette smoke sampled from an environmental chamber exposed BPEAnit to much lower concentrations of particles, but still resulted in a clearly detectible increase in fluorescence intensity with sampling time. It was calculated that the amount of ROS was equivalent to 50 ± 2 nmol per mg of particulate matter; however, this value decreased with ageing of the particles in the chamber. Overall, BPEAnit was shown to provide a sensitive response related to the oxidative capacity of the particulate matter. These findings present a good basis for employing the new BPEAnit probe for the investigation of particle-related ROS generated from cigarette smoke as well as from other combustion sources.

  17. On supersonic combustion

    Institute of Scientific and Technical Information of China (English)

    袁生学

    1999-01-01

    Some basic concepts and features of supersonic combustion are explained from the view point of macroscopic aerodynamics. Two kinds of interpretations of supersonic combustion are proposed. The difference between supersonic combustion and subsonic combustion is discussed, and the mechanism of supersonic combustion propagation and the limitation of heat addition in supersonic flow are pointed out. The results of the calculation of deflagration in supersonic flow show that the entropy increment and the total pressure loss of the combustion products may decrease with the increase of combustion velocity. It is also demonstrated that the oblique detonation wave angle may not be controlled by the wedge angle under weak underdriven solution conditions and be determined only by combustion velocity. Therefore, the weak underdriven solution may become self-sustaining oblique detonation waves with a constant wave angle.

  18. Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — For more than 30 years The Combustion Research Facility (CRF) has served as a national and international leader in combustion science and technology. The need for a...

  19. Fostering Students' Meta-understanding of Scientific Principles as Scientific Thinking : In the Case of a 6th Grade Unit about "Combustion"

    OpenAIRE

    坂本, 美紀; 村山, 功; 山口, 悦司; 稲垣, 成哲; 大島, 純; 大島, 律子; 中山, 迅; 竹中, 真希子; 山本, 智一; 藤本, 雅司; 竹下, 裕子; 橘, 早苗

    2007-01-01

    Students sometimes fail to give a theory-based explanation of phenomena after they learn scientific principles. The present study investigated the optimum method to train students in scientific thinking in elementary school science lessons. We conducted three experimental lessons to foster students' meta-understanding of scientific principles about combustion. Sixth graders collaboratively inquired into the difficult-to-understand phenomena of combustion for a theory-based explanation. Based ...

  20. Preparation of imprinted cryogel cartridge for chiral separation of l-phenylalanine.

    Science.gov (United States)

    Akgönüllü, Semra; Yavuz, Handan; Denizli, Adil

    2017-06-01

    l-Phe-imprinted cryogel cartridge was prepared for the chiral separation of l-Phe. N-Methacryloyl l-phenylalanine (MAPA) was used as a functional monomer for complexing with l-Phe. The selectivity of the membranes was investigated by using d-Phe, l-Trp, and d-Trp as competitor molecules. The PHEMAPA-l-Trp membranes were 6.4, 4.3, and 5.5 times more selective for l-Phe than d-Phe, l-Trp, and d-Trp, respectively. The PHEMAPA-l-Phe cryogel cartridge was incorporated into the fast protein liquid chromatography (FPLC) equipment and was able to separate D,l-Phe racemic mixture efficiently. The PHEMAPA-l-Phe membranes were shown to be reusable many times without significant loss of the adsorption capacity.

  1. Purification of Astaxanthin from Laminariajaponica by Ionic Liquid-based Monolithic Cartridge

    Institute of Scientific and Technical Information of China (English)

    YOON Chang-hwan; ZHU Tao; ROW Kyung-ho

    2012-01-01

    An effective and accurate method was developed for the extraction of astaxanthin from Laminariajaponica with subsequent separation by ionic liquid-based monolithic cartridge.The optimized extraction conditions including extraction solvent(ethanol),extraction time(90 min) and ultrasonic power(75 W) were obtained by systematical investigation.Chromatographic analysis was performed on a C18 column with ultraviolet(UV) detection at 476nm,and a solution consisting of methanol/acetonitrile/H20/dichloromethane(83:6:6:5,volume ratio) was used as the mobile phase at a flow rate of 0.7 mL/min.After ionic liquid-based monolithic solid phase extraction,17.82 μg/g astaxanthin was obtained from Laminariajaponica.This ionic liquid-based monolithic cartridge exhibits high affinity and selectivity for astaxanthin,and it can be potentially used as the stationary phase of high performance liquid chromatography( HPLC).

  2. Using the PL/SQL Cartridge of the Oracle Application Server to Deploy Web Applications

    Energy Technology Data Exchange (ETDEWEB)

    Begovich, C.L.

    1999-06-14

    Deploying business applications on the internal Web is a priority at Oak Ridge National Laboratory (Lockheed Martin Energy Research) and Lockheed Martin Energy Systems, Inc. as with most corporations. Three separate applications chose the Oracle Application Server (OAS), using the PL/SQL cartridge as a Web deployment method. This method was chosen primarily because the data was already stored in Oracle tables and developers knew HJSQL or at least SQL. The Database Support group had the responsibility of installing, testing, and determining standard methods for interfacing with the PL/SQL cartridge of the OAS. Note that the term Web Application Server was used for version 3, but in this discussion, OAS will be used for both version 3 and version 4.

  3. Determination of 137Cs in large volume seawater using Cu-hexacyanoferrate cartridge filters

    Science.gov (United States)

    Visetpotjanakit, S.; Tumnoi, Y.

    2017-06-01

    A simple method to determine 137Cs in seawater has been developed based on the use of a Cu-hexacyanoferrate scavenger. The Cu-hexacyanoferrate supported on cotton wound cartridge filter was used to absorb 137Cs from seawater by passing large volumes over the cartridge filters with flowrate of 240 L hr-1. Results from the Cu-hexacyanoferrate method were proved acceptable for accuracy with bias below ± 20 % i.e. - 9.16 to + 18.55 % when compared with the traditional ammonium molybdophosphate pre-concentration method. This developed method is cost-effective and less time consuming. In addition it can be easily performed at sampling fields.

  4. COMBUSTION SIMULATION IN A SPARK IGNITION ENGINE CYLINDER: EFFECTS OF AIR-FUEL RATIO ON THE COMBUSTION DURATION

    Directory of Open Access Journals (Sweden)

    Nureddin Dinler

    2010-01-01

    Full Text Available Combustion is an important subject of internal combustion engine studies. To reduce the air pollution from internal combustion engines and to increase the engine performance, it is required to increase combustion efficiency. In this study, effects of air/fuel ratio were investigated numerically. An axisymmetrical internal combustion engine was modeled in order to simulate in-cylinder engine flow and combustion. Two dimensional transient continuity, momentum, turbulence, energy, and combustion equations were solved. The k-e turbulence model was employed. The fuel mass fraction transport equation was used for modeling of the combustion. For this purpose a computational fluid dynamics code was developed by using the finite volume method with FORTRAN programming code. The moving mesh was utilized to simulate the piston motion. The developed code simulates four strokes of engine continuously. In the case of laminar flow combustion, Arrhenius type combustion equations were employed. In the case of turbulent flow combustion, eddy break-up model was employed. Results were given for rich, stoichiometric, and lean mixtures in contour graphs. Contour graphs showed that lean mixture (l = 1.1 has longer combustion duration.

  5. Continuous-flow multi-analyte biosensor cartridge with controllable linear response range.

    Science.gov (United States)

    Frey, Olivier; Talaei, Sara; van der Wal, Peter D; Koudelka-Hep, Milena; de Rooij, Nico F

    2010-09-01

    This article presents the design and fabrication of a microfluidic biosensor cartridge for the continuous and simultaneous measurement of biologically relevant analytes in a sample solution. The biosensor principle is based on the amperometric detection of hydrogen peroxide using enzyme-modified electrodes. The low-integrated and disposable cartridge is fabricated in PDMS and SU-8 by rapid prototyping. The device is designed in such a way that it addresses two major challenges of biosensors using microfluidics approaches. Firstly, the enzymatic membrane is deposited on top of the platinum electrodes via a microfluidic deposition channel from outside the cartridge. This decouples the membrane deposition from the cartridge fabrication and enables the user to decide when and with what mixture he wants to modify the electrode. Secondly, by using laminar sheath-flow of the sample and a buffer solution, a dynamic diffusion layer is created. The analyte has to diffuse through the buffer solution layer before it can reach the immobilized enzyme membrane on the electrode. Controlling of the thickness of the diffusion layer by variation of the flow-rate of the two layers enables the user to adjust the sensitivity and the linear region of the sensor. The point where the buffer and sample stream join proved critical in creating the laminar sheath-flow. Results of computational simulations considering fluid dynamics and diffusion are presented. The consistency of the device was investigated through detection of glucose and lactate and are in accordance with the CFD simulations. A sensitivity of 157+/-28 nA/mM for the glucose sensor and 79+/-12 nA/mM for the lactate sensor was obtained. The linear response range of these biosensors could be increased from initially 2 mM up to 15 mM with a limit of detection of 0.2 mM.

  6. Pulverized-coal-firing small-size boiler for coal-cartridge system

    Energy Technology Data Exchange (ETDEWEB)

    1986-12-01

    Kawasaki Heavy Industries, Ltd. supplied a test boiler plant to the Iwakuni Experimental Station of the Coal Cartridge System (CCS) Promotion Association in September 1985; this was the first pulverized-coal-fired small industrial boiler in Japan. Tests will be performed for two years, until fiscal 1987, at the CCS Iwakuni Experimental Station to establish a method of coal-firing with a performance comparable to heavy oil firing. The boiler plant has been operating satisfactorily.

  7. End of Service Life Indicator (ESLI) for Respirator Cartridges. Part 1: Literature Review

    Science.gov (United States)

    2005-07-01

    containing a relatively simple fibre optic chemical sensor (FOCS) for indicating the end of service life of the unit. The indicator concept design...light intensity passing to the detector decreased. Figure 28: Fibre optic containing a microporous glass section (surface area ~250m2/g) [95...Figure 29: Fibre optic chemical sensor (FOCS) for respirator cartridge (A) FOCS with light source and detector (B) electronic module connected

  8. Hollow-Fiber Cartridges: Model Systems for Virus Removal from Blood

    Science.gov (United States)

    Jacobitz, Frank; Menon, Jeevan

    2005-11-01

    Aethlon Medical is developing a hollow-fiber hemodialysis device designed to remove viruses and toxins from blood. Possible target viruses include HIV and pox-viruses. The filter could reduce virus and viral toxin concentration in the patient's blood, delaying illness so the patient's immune system can fight off the virus. In order to optimize the design of such a filter, the fluid mechanics of the device is both modeled analytically and investigated experimentally. The flow configuration of the proposed device is that of Starling flow. Polysulfone hollow-fiber dialysis cartridges were used. The cartridges are charged with water as a model fluid for blood and fluorescent latex beads are used in the experiments as a model for viruses. In the experiments, properties of the flow through the cartridge are determined through pressure and volume flow rate measurements of water. The removal of latex beads, which are captured in the porous walls of the fibers, was measured spectrophotometrically. Experimentally derived coefficients derived from these experiments are used in the analytical model of the flow and removal predictions from the model are compared to those obtained from the experiments.

  9. Behavioral response and pain perception to computer controlled local anesthetic delivery system and cartridge syringe.

    Science.gov (United States)

    Yogesh Kumar, T D; John, J Baby; Asokan, Sharath; Geetha Priya, P R; Punithavathy, R; Praburajan, V

    2015-01-01

    The present study evaluated and compared the pain perception, behavioral response, physiological parameters, and the role of topical anesthetic administration during local anesthetic administration with cartridge syringe and computer controlled local anesthetic delivery system (CCLAD). A randomized controlled crossover study was carried out with 120 children aged 7-11 years. They were randomly divided into Group A: Receiving injection with CCLAD during first visit; Group B: Receiving injection with cartridge syringe during first visit. They were further subdivided into three subgroups based on the topical application used: (a) 20% benzocaine; (b) pressure with cotton applicator; (c) no topical application. Pulse rate and blood pressure were recorded before and during injection procedure. Objective evaluation of disruptive behavior and subjective evaluation of pain were done using face legs activity cry consolability scale and modified facial image scale, respectively. The washout period between the two visits was 1-week. Injections with CCLAD produced significantly lesser pain response, disruptive behavior (P < 0.001), and pulse rate (P < 0.05) when compared to cartridge syringe injections. Application of benzocaine produced lesser pain response and disruptive behavior when compared to the other two subgroups, although the result was not significant. Usage of techniques which enhance behavioral response in children like injections with CCLAD can be considered as a possible step toward achieving a pain-free pediatric dental practice.

  10. Removal of Cryptosporidium and polystyrene microspheres from swimming pool water with sand, cartridge, and precoat filters.

    Science.gov (United States)

    Amburgey, James E; Walsh, Kimberly J; Fielding, Roy R; Arrowood, Michael J

    2012-03-01

    Cryptosporidium has caused the majority of waterborne disease outbreaks in treated recreational water venues in the USA for many years running. This research project evaluated some common US swimming pool filters for removing Cryptosporidium oocysts, 5-µm diameter polystyrene microspheres, and 1-µm diameter polystyrene microspheres. A 946 L hot tub with interchangeable sand, cartridge, and precoat filters was used at room temperature for this research. Simulated pool water for each experiment was created from Charlotte, NC (USA) tap water supplemented with alkalinity, hardness, chlorine, and a mixture of artificial sweat and urine. Precoat (i.e., diatomaceous earth and perlite) filters demonstrated pathogen removal efficiencies of 2.3 to 4.4 log (or 99.4-99.996%). However, sand and cartridge filters had average Cryptosporidium removals of 0.19 log (36%) or less. The combined low filter removal efficiencies of sand and cartridge filters along with the chlorine-resistant properties of Cryptosporidium oocysts could indicate a regulatory gap warranting further attention and having significant implications on the protection of public health in recreational water facilities. The 5-µm microspheres were a good surrogate for Cryptosporidium oocysts in this study and hold promise for use in future research projects, field trials, and/or product testing on swimming pool filters.

  11. Behavioral response and pain perception to computer controlled local anesthetic delivery system and cartridge syringe

    Directory of Open Access Journals (Sweden)

    T D Yogesh Kumar

    2015-01-01

    Full Text Available Aim: The present study evaluated and compared the pain perception, behavioral response, physiological parameters, and the role of topical anesthetic administration during local anesthetic administration with cartridge syringe and computer controlled local anesthetic delivery system (CCLAD. Design: A randomized controlled crossover study was carried out with 120 children aged 7-11 years. They were randomly divided into Group A: Receiving injection with CCLAD during first visit; Group B: Receiving injection with cartridge syringe during first visit. They were further subdivided into three subgroups based on the topical application used: (a 20% benzocaine; (b pressure with cotton applicator; (c no topical application. Pulse rate and blood pressure were recorded before and during injection procedure. Objective evaluation of disruptive behavior and subjective evaluation of pain were done using face legs activity cry consolability scale and modified facial image scale, respectively. The washout period between the two visits was 1-week. Results: Injections with CCLAD produced significantly lesser pain response, disruptive behavior (P < 0.001, and pulse rate (P < 0.05 when compared to cartridge syringe injections. Application of benzocaine produced lesser pain response and disruptive behavior when compared to the other two subgroups, although the result was not significant. Conclusion: Usage of techniques which enhance behavioral response in children like injections with CCLAD can be considered as a possible step toward achieving a pain-free pediatric dental practice.

  12. Is the exploding powder gas of the propellant from blank cartridges sterile?

    Science.gov (United States)

    Rothschild, M A; Liesenfeld, O

    1996-11-11

    Shots from blank weapons loaded with blank cartridges, when fired from close range or as a contact shot, almost always cause the skin to burst open and lead to injuries to structures below the surface. Subsequently, wound infections are often observed. In addition to the introduction of skin germs, the possibility exists that contaminated propellants may enter into consideration as a source of infection. Using step-by-step experimental procedures we were able to demonstrate that: 1. Blank cartridge propellants were almost always contaminated with Bacillus cereus (nitrocellulose powder more so than black powder); 2. When the shot is fired numerous bacteria survive and are forced out with the gunsmoke from the weapon and thus find their way into the wound. In principle, blank cartridge propellant thus exhibits as much potential for wound infection as the skin germs. Clearly, the species B. cereus is prominent in this context. For open injuries even with 'harmless' blank weapons, an antibiotic prophylaxis should always be administered.

  13. Reagent-loaded cartridges for valveless and automated fluid delivery in microfluidic devices.

    Science.gov (United States)

    Linder, Vincent; Sia, Samuel K; Whitesides, George M

    2005-01-01

    An important problem in the life sciences and in health care is simple and rapid detection of biomarkers. Although microfluidic devices are potentially useful in addressing this problem, current techniques for automating fluid delivery--which include valves and electroosmosis--require sophisticated microfabrication of the chip, bulky instrumentation, or both. In this paper, we describe a simple and reliable technique for storing and delivering a sequence of reagents to a microfluidic device. The technique is low-cost, requires minimal user intervention, and can be performed in resource-poor settings (e.g., outside of a laboratory) in the absence of electricity and computer-controlled equipment. In this method, cartridges made of commercially available tubing are filled by sequentially injecting plugs of reagents separated by air spacers. The air spacers prevent the reagents from mixing with each other during cartridge preparation, storage, and usage. As an example, we used this "plug-in cartridge" technology to complete a solid-phase immunoassay in a microchannel in 2 min with low-nanomolar sensitivity and demonstrate the diagnosis of HIV in 13 min.

  14. 废弃硒鼓资源化技术研究%Processing of Waste Toner Cartridge Recycling

    Institute of Scientific and Technical Information of China (English)

    黄庆; 王景伟; 王鹏程; 邓毅

    2014-01-01

    Toner cartridge as the key component is widely used in laser printer, photocopier and fax machine. As the quantity of discard toner cartridge is increasing year by year, recycling of waste toner cartridge has attracted domestic and international attention. The material composition of waste toner cartridge is introduced, as well as the available recycling of waste toner cartridge and the environ-mental hazard caused by the toners which remained in the cartridge. Simultaneously, processes and technologies applied in waste toner cartridge recycling by domestic and international are summarized. Accordingly, the potential problems existing in waste toner cartridge recycling technologies are discussed, and constructive suggestions for improvement of recycling technology in the future are provided.%硒鼓作为核心部件被广泛应用于激光打印机、复印机和传真机中。随着硒鼓的报废量逐年增大,废弃硒鼓的无害化处理和资源化利用越来越受到人们的关注。主要介绍了废弃硒鼓的材料组分、可资源化性和残留墨粉的环境危害性,总结了国内外废弃硒鼓资源化技术和特点,并提出了废弃硒鼓资源化技术中存在的问题,为未来废弃硒鼓资源化技术的改进提供建设性意见。

  15. Cartridge syringe vs computer controlled local anesthetic delivery system: Pain related behaviour over two sequential visits - a randomized controlled trial.

    Science.gov (United States)

    Thoppe-Dhamodhara, Yogesh-Kumar; Asokan, Sharath; John, Baby-John; Pollachi-Ramakrishnan, GeethaPriya; Ramachandran, Punithavathy; Vilvanathan, Praburajan

    2015-10-01

    Local anesthetic injection is one of the most anxiety provoking procedure in dentistry. Knowledge about change in pain related behaviour during consecutive visits helps in and scheduling of treatment procedures and management of children in dental clinic. To compare the pain perception, behavioural response and the associated change in physiological parameters while receiving local anesthesia injection with cartridge syringe and computer controlled local anesthetic delivery system (CCLAD) over two consecutive visits. In this randomized controlled cross over trial, 120 children aged 7 - 11 years were randomly divided into group A: receiving injections with CCLAD during first visit; group B: receiving injections with cartridge syringe during first visit. The physiological parameters (heart rate and blood pressure) were recorded before and during injection procedure. Objective evaluation of disruptive behaviour and subjective evaluation of pain perceived were done using Face Legs Activity Cry Consolability (FLACC) scale and modified facial image scale (FIS) respectively. No statistical difference in pain response (p= 0.164) and disruptive behaviour (p = 0.120) between cartridge syringe and CCLAD injections were seen during the first visit although the latter showed lesser scores. However, during the second visit there were significant increase in pain response (p = 0.004) and disruptive behaviour (p = 0.006) in cartridge syringe group with an associated increase in heart rate. Injections with CCLAD produced lesser pain ratings and disruptive behaviour than cartridge syringe in children irrespective of order of visit. Behaviour, cartridge syringe, CCLAD, local anesthesia.

  16. Filtration Combustion in Smoldering and SHS

    Science.gov (United States)

    Matkowsky, Bernard J.

    2001-01-01

    Smolder waves and SHS (self-propagating high-temperature synthesis) waves are both examples of filtration combustion waves propagating in porous media. Smoldering combustion is important for the study of fire safety. Smoldering itself can cause damage, its products are toxic and it can also lead to the more dangerous gas phase combustion which corresponds to faster propagation at higher temperatures. In SHS , a porous solid sample, consisting of a finely ground powder mixture of reactants, is ignited at one end. A high temperature thermal wave, having a frontal structure, then propagates through the sample converting reactants to products. The SHS technology appears to enjoy a number of advantages over the conventional technology, in which the sample is placed in a furnace and "baked" until it is "well done". The advantages include shorter synthesis times, greater economy, in that the internal energy of the reactions is employed rather than the costly external energy of the furnace, purer products, simpler equipment and no intrinsic limitation on the size of the sample to be synthesized as exists in the conventional technology. When delivery of reactants through the pores to the reaction site is an important aspect of the combustion process, it is referred to as filtration combustion. The two types of filtration combustion have a similar mathematical formulation, describing the ignition, propagation and extinction of combustion waves in porous media. The goal in each case, however, is different. In smoldering the desired goal is to prevent propagation, whereas in SHS the goal is to ensure propagation of the combustion wave, leading to the synthesis of desired products. In addition, the scales in the two areas of application differ. Smoldering generally occurs at lower temperatures and propagation velocities than in SHS nevertheless, the two applications have much in common so that what is learned fit make application can be used to advantage in the other. In porous

  17. Boiler using combustible fluid

    Science.gov (United States)

    Baumgartner, H.; Meier, J.G.

    1974-07-03

    A fluid fuel boiler is described comprising a combustion chamber, a cover on the combustion chamber having an opening for introducing a combustion-supporting gaseous fluid through said openings, means to impart rotation to the gaseous fluid about an axis of the combustion chamber, a burner for introducing a fluid fuel into the chamber mixed with the gaseous fluid for combustion thereof, the cover having a generally frustro-conical configuration diverging from the opening toward the interior of the chamber at an angle of between 15/sup 0/ and 55/sup 0/; means defining said combustion chamber having means defining a plurality of axial hot gas flow paths from a downstream portion of the combustion chamber to flow hot gases into an upstream portion of the combustion chamber, and means for diverting some of the hot gas flow along paths in a direction circumferentially of the combustion chamber, with the latter paths being immersed in the water flow path thereby to improve heat transfer and terminating in a gas outlet, the combustion chamber comprising at least one modular element, joined axially to the frustro-conical cover and coaxial therewith. The modular element comprises an inner ring and means of defining the circumferential, radial, and spiral flow paths of the hot gases.

  18. Measuring Combustion Advance in Solid Propellants

    Science.gov (United States)

    Yang, L. C.

    1986-01-01

    Set of gauges on solid-propellant rocket motor with electrically insulating case measures advance of combustion front and local erosion rates of propellant and insulation. Data furnished by gauges aid in motor design, failure analysis, and performance prediction. Technique useful in determining propellant uniformity and electrical properties of exhaust plum. Gauges used both in flight and on ground. Foilgauge technique also useful in basic research on pulsed plasmas or combustion of solids.

  19. Coal combustion products

    Science.gov (United States)

    Kalyoncu, R.S.; Olson, D.W.

    2001-01-01

    Coal-burning powerplants, which supply more than half of U.S. electricity, also generate coal combustion products, which can be both a resource and a disposal problem. The U.S. Geological Survey collaborates with the American Coal Ash Association in preparing its annual report on coal combustion products. This Fact Sheet answers questions about present and potential uses of coal combustion products.

  20. Indirect combustion noise of auxiliary power units

    Science.gov (United States)

    Tam, Christopher K. W.; Parrish, Sarah A.; Xu, Jun; Schuster, Bill

    2013-08-01

    Recent advances in noise suppression technology have significantly reduced jet and fan noise from commercial jet engines. This leads many investigators in the aeroacoustics community to suggest that core noise could well be the next aircraft noise barrier. Core noise consists of turbine noise and combustion noise. There is direct combustion noise generated by the combustion processes, and there is indirect combustion noise generated by the passage of combustion hot spots, or entropy waves, through constrictions in an engine. The present work focuses on indirect combustion noise. Indirect combustion noise has now been found in laboratory experiments. The primary objective of this work is to investigate whether indirect combustion noise is also generated in jet and other engines. In a jet engine, there are numerous noise sources. This makes the identification of indirect combustion noise a formidable task. Here, our effort concentrates exclusively on auxiliary power units (APUs). This choice is motivated by the fact that APUs are relatively simple engines with only a few noise sources. It is, therefore, expected that the chance of success is higher. Accordingly, a theoretical model study of the generation of indirect combustion noise in an Auxiliary Power Unit (APU) is carried out. The cross-sectional areas of an APU from the combustor to the turbine exit are scaled off to form an equivalent nozzle. A principal function of a turbine in an APU is to extract mechanical energy from the flow stream through the exertion of a resistive force. Therefore, the turbine is modeled by adding a negative body force to the momentum equation. This model is used to predict the ranges of frequencies over which there is a high probability for indirect combustion noise generation. Experimental spectra of internal pressure fluctuations and far-field noise of an RE220 APU are examined to identify anomalous peaks. These peaks are possible indirection combustion noise. In the case of the

  1. Research Combustion Laboratory (RCL)

    Data.gov (United States)

    Federal Laboratory Consortium — The Research Combustion Laboratory (RCL) develops aerospace propulsion technology by performing tests on propulsion components and materials. Altitudes up to 137,000...

  2. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    Ashlines: To promote and support the commercially viable and environmentally sound recycling of coal combustion byproducts for productive uses through scientific research, development, and field testing.

  3. Research Combustion Laboratory (RCL)

    Data.gov (United States)

    Federal Laboratory Consortium — The Research Combustion Laboratory (RCL) develops aerospace propulsion technology by performing tests on propulsion components and materials. Altitudes up to 137,000...

  4. DYNAMIC CHARACTERISTICS OF LARGE FLOW RATING ELECTRO-HYDRAULIC PROPORTIONAL CARTRIDGE VALVE

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A kind of cartridge servo proportional valve is discussed, which can be used for controlling large flow rate with high performance. By analyzing the structure principle of the valve, the transfer function of the valve is derived. With the transfer function, some structure elements that may affect its performance are investigated. Through the numerical simulation and test study, some principles of optimality and effective methods for improving the dynamic performance of the valve are proposed. The test results conform to the results of the theoretical analysis and simulation, which proves the correctness of the study and simulation works. The paper provides theoretical basis for engineering applications and series expanding design works.

  5. Development and Implementation of a Formal Framework for Bottom-up Uncertainty Analysis of Input Emissions: Case Study of Residential Wood Combustion

    Science.gov (United States)

    Zhao, S.; Mashayekhi, R.; Saeednooran, S.; Hakami, A.; Ménard, R.; Moran, M. D.; Zhang, J.

    2016-12-01

    We have developed a formal framework for documentation, quantification, and propagation of uncertainties in upstream emissions inventory data at various stages leading to the generation of model-ready gridded emissions through emissions processing software such as the EPA's SMOKE (Sparse Matrix Operator Kernel Emissions) system. To illustrate this framework we present a proof-of-concept case study of a bottom-up quantitative assessment of uncertainties in emissions from residential wood combustion (RWC) in the U.S. and Canada. Uncertainties associated with key inventory parameters are characterized based on existing information sources, including the American Housing Survey (AHS) from the U.S. Census Bureau, Timber Products Output (TPO) surveys from the U.S. Forest Service, TNS Canadian Facts surveys, and the AP-42 emission factor document from the U.S. EPA. The propagation of uncertainties is based on Monte Carlo simulation code external to SMOKE. Latin Hypercube Sampling (LHS) is implemented to generate a set of random realizations of each RWC inventory parameter, for which the uncertainties are assumed to be normally distributed. Random realizations are also obtained for each RWC temporal and chemical speciation profile and spatial surrogate field external to SMOKE using the LHS approach. SMOKE outputs for primary emissions (e.g., CO, VOC) using both RWC emission inventory realizations and perturbed temporal and chemical profiles and spatial surrogates show relative uncertainties of about 30-50% across the U.S. and about 70-100% across Canada. Positive skewness values (up to 2.7) and variable kurtosis values (up to 4.8) were also found. Spatial allocation contributes significantly to the overall uncertainty, particularly in Canada. By applying this framework we are able to produce random realizations of model-ready gridded emissions that along with available meteorological ensembles can be used to propagate uncertainties through chemical transport models. The

  6. Formaldehyde and acetaldehyde emissions from residential wood combustion in Portugal

    Science.gov (United States)

    Cerqueira, Mário; Gomes, Luís; Tarelho, Luís; Pio, Casimiro

    2013-06-01

    A series of experiments were conducted to characterize formaldehyde and acetaldehyde emissions from residential combustion of common wood species growing in Portugal. Five types of wood were investigated: maritime pine (Pinus pinaster), eucalyptus (Eucalyptus globulus), cork oak (Quercus suber), holm oak (Quercus rotundifolia) and pyrenean oak (Quercus pyrenaica). Laboratory experiments were performed with a typical wood stove used for domestic heating in Portugal and operating under realistic home conditions. Aldehydes were sampled from diluted combustion flue gas using silica cartridges coated with 2,4-dinitrophenylhydrazine and analyzed by high performance liquid chromatography with diode array detection. The average formaldehyde to acetaldehyde concentration ratio (molar basis) in the stove flue gas was in the range of 2.1-2.9. Among the tested wood types, pyrenean oak produced the highest emissions for both formaldehyde and acetaldehyde: 1772 ± 649 and 1110 ± 454 mg kg-1 biomass burned (dry basis), respectively. By contrast, maritime pine produced the lowest emissions: 653 ± 151 and 371 ± 162 mg kg-1 biomass (dry basis) burned, respectively. Aldehydes were sampled separately during distinct periods of the holm oak wood combustion cycles. Significant variations in the flue gas concentrations were found, with higher values measured during the devolatilization stage than in the flaming and smoldering stages.

  7. Novel pre-fractionation method of trans fatty acids by gas chromatography with silver-ion cartridge column.

    Science.gov (United States)

    Goto, Hirofumi; Shionoya, Noriko; Sugie, Megumi; Tominaga, Makoto; Shimelis, Olga; Taniguchi, Makoto; Igarashi, Tomoji; Hirata, Yoshiaki

    2012-01-01

    We developed a novel pre-separation method of trans fatty acids (TFAs) using a silver-ion cartridge column and GC. As a preliminary study, a mixture of fatty acid methyl esters consisting of saturated, cis-unsaturated, and trans-unsaturated fatty acids was dissolved in dichloromethane and loaded onto a Bond Elut SCX ion-exchange cartridge column that was converted to the silver-ion form. The column was then eluted with dichloromethane to obtain the saturated fatty acids, dichloromethane/ethyl acetate (90/10) for the trans mono-ene, dichloromethane/ethyl acetate (65/35) for the cis mono-ene, dichloromethane/acetone (60/40) for the trans di-ene, and acetone/acetonitrile (80/20) for the others. Satisfactory separation of the cis/trans isomers was confirmed by GC analysis. To generalize this technique, the elution conditions of the ready-to-use Discovery Ag-ION SPE cartridge column were also optimized. Both cartridge columns had good separation, recovery, and repeatability. Peer laboratory verification was carried out between two laboratories using different production lots of the ready-to-use cartridge column, and the robustness of the product and reproducibility of the method were found to be satisfactory. This technique is therefore a powerful tool not only for routine analyses of TFAs in oils, fats, and foods but also for detailed analyses of TFAs in various research fields.

  8. Steady state HNG combustion modeling

    Energy Technology Data Exchange (ETDEWEB)

    Louwers, J.; Gadiot, G.M.H.J.L. [TNO Prins Maurits Lab., Rijswijk (Netherlands); Brewster, M.Q. [Univ. of Illinois, Urbana, IL (United States); Son, S.F. [Los Alamos National Lab., NM (United States); Parr, T.; Hanson-Parr, D. [Naval Air Warfare Center, China Lake, CA (United States)

    1998-04-01

    Two simplified modeling approaches are used to model the combustion of Hydrazinium Nitroformate (HNF, N{sub 2}H{sub 5}-C(NO{sub 2}){sub 3}). The condensed phase is treated by high activation energy asymptotics. The gas phase is treated by two limit cases: the classical high activation energy, and the recently introduced low activation energy approach. This results in simplification of the gas phase energy equation, making an (approximate) analytical solution possible. The results of both models are compared with experimental results of HNF combustion. It is shown that the low activation energy approach yields better agreement with experimental observations (e.g. regression rate and temperature sensitivity), than the high activation energy approach.

  9. Research on Marine Boiler's Pressurized Combustion and Heat Transfer

    Institute of Scientific and Technical Information of China (English)

    Pingjian MING; Renqiu JIANG; Yanjun LI; Baozhi SUN

    2005-01-01

    The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.

  10. Strobes: An oscillatory combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; Lingen, J.N.J. van; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the beginni

  11. Strobes: An Oscillatory Combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; van Lingen, J.N.J.; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the beginni

  12. Lectures on combustion theory

    Energy Technology Data Exchange (ETDEWEB)

    Burstein, S.Z.; Lax, P.D.; Sod, G.A. (eds.)

    1978-09-01

    Eleven lectures are presented on mathematical aspects of combustion: fluid dynamics, deflagrations and detonations, chemical kinetics, gas flows, combustion instability, flame spread above solids, spark ignition engines, burning rate of coal particles and hydrocarbon oxidation. Separate abstracts were prepared for three of the lectures. (DLC)

  13. Fifteenth combustion research conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-06-01

    The BES research efforts cover chemical reaction theory, experimental dynamics and spectroscopy, thermodynamics of combustion intermediates, chemical kinetics, reaction mechanisms, combustion diagnostics, and fluid dynamics and chemically reacting flows. 98 papers and abstracts are included. Separate abstracts were prepared for the papers.

  14. Coal Combustion Science

    Energy Technology Data Exchange (ETDEWEB)

    Hardesty, D.R. (ed.); Fletcher, T.H.; Hurt, R.H.; Baxter, L.L. (Sandia National Labs., Livermore, CA (United States))

    1991-08-01

    The objective of this activity is to support the Office of Fossil Energy in executing research on coal combustion science. This activity consists of basic research on coal combustion that supports both the Pittsburgh Energy Technology Center Direct Utilization Advanced Research and Technology Development Program, and the International Energy Agency Coal Combustion Science Project. Specific tasks for this activity include: (1) coal devolatilization - the objective of this risk is to characterize the physical and chemical processes that constitute the early devolatilization phase of coal combustion as a function of coal type, heating rate, particle size and temperature, and gas phase temperature and oxidizer concentration; (2) coal char combustion -the objective of this task is to characterize the physical and chemical processes involved during coal char combustion as a function of coal type, particle size and temperature, and gas phase temperature and oxygen concentration; (3) fate of mineral matter during coal combustion - the objective of this task is to establish a quantitative understanding of the mechanisms and rates of transformation, fragmentation, and deposition of mineral matter in coal combustion environments as a function of coal type, particle size and temperature, the initial forms and distribution of mineral species in the unreacted coal, and the local gas temperature and composition.

  15. Combustion of coffee husks

    Energy Technology Data Exchange (ETDEWEB)

    Saenger, M.; Hartge, E.-U.; Werther, J. [Technical Univ. Hamburg-Harburg, Chemical Engineering 1, Hamburg (Germany); Ogada, T.; Siagi, Z. [Moi Univ., Dept. of Production Engineering, Eldoret (Kenya)

    2001-05-01

    Combustion mechanisms of two types of coffee husks have been studied using single particle combustion techniques as well as combustion in a pilot-scale fluidized bed facility (FBC), 150 mm in diameter and 9 m high. Through measurements of weight-loss and particle temperatures, the processes of drying, devolatilization and combustion of coffee husks were studied. Axial temperature profiles in the FBC were also measured during stationary combustion conditions to analyse the location of volatile release and combustion as a function of fuel feeding mode. Finally the problems of ash sintering were analysed. The results showed that devolatilization of coffee husks (65-72% volatile matter, raw mass) starts at a low temperature range of 170-200degC and takes place rapidly. During fuel feeding using a non water-cooled system, pyrolysis of the husks took place in the feeder tube leading to blockage and non-uniform fuel flow. Measurements of axial temperature profiles showed that during under-bed feeding, the bed and freeboard temperatures were more or less the same, whereas for over-bed feeding, freeboard temperatures were much higher, indicating significant combustion of the volatiles in the freeboard. A major problem observed during the combustion of coffee husks was ash sintering and bed agglomeration. This is due to the low melting temperature of the ash, which is attributed to the high contents of K{sub 2}O (36-38%) of the coffee husks. (Author)

  16. 弹射药筒局部热处理%Local Thermal Treatment on Catapult Cartridge

    Institute of Scientific and Technical Information of China (English)

    闻国民; 杨国义; 牛俊杰; 魏军伟; 陈全明

    2014-01-01

    针对弹射药筒局部热处理的质量性能要求,对感应加热技术进行研究。基于加热时间、温度和升温速度对筒壁的影响,从频率选择、感应器和工装设计3个方面进行分析,得到频率、功率和时间参数。分析结果表明:该方法使工件的抗拉强度、延伸率达到了要求,产品性能稳定,并能有效控制药筒口部的物理性能。%The technology of induction heating fusing had been researched in allusion to the demand of quality and property of the local thermal treatment on catapult cartridge. In view of the effect on cylinder wall about heating time, temperature and the rate of warming, parameter of frequency, temperature and time had been found according to the analysis in these three points including frequency selection, sensors and equipment design. Interrelated analyses concluded that these measures ensured the tensile strength and elongation, and made the performance stable. Also, physical properties of cartridge mouth had been controlled effectively.

  17. Hydrogen Car Cartridges: A New Strategy for Hydrogen Storage, Delivering and Refueling

    Energy Technology Data Exchange (ETDEWEB)

    Prosini, Pier Paolo

    2007-07-01

    The purpose of the project is to introduce a sustainable model in the automotive field, guarantying the Kyoto agreements. The aim of the project is to develop an innovative hydrogen tank able to power an hydrogen fuel cell car with the same performance of liquid fuelled cars. Most of the system performance are expected to satisfy the Department of Energy (DOE) goals for 2015. The hydrogen releasing system is based on solid NaBH4 which is hydrolyzed with water or steam to obtain hydrogen. Sodium borate is obtained as by-product and it has to be recycled. Pure and humidified hydrogen, ready to be utilized in a fuel cell, is obtained by a simple and sure way. Hydrogen is produced only when it is requested and therefore there is never pressurized hydrogen or hydrogen overproduction The system works at atmospheric pressure avoiding the problems related to handling and storing pressurized gas. The car fuelling could be performed in area like the present service stations. The used cartridges can be removed and substituted by new cartridges. Contemporarily a water tank should be refilled. To improve the total energetic yield it was also proposed a NaBH4 regeneration process directly starting from the products of hydrolysis. (auth)

  18. A Calibration-Free, Noncontact, Disposable Liquid Dispensing Cartridge Featuring an Online Process Control.

    Science.gov (United States)

    Bammesberger, Stefan Borja; Malki, Imad; Ernst, Andreas; Zengerle, Roland; Koltay, Peter

    2014-08-01

    We present a noncontact liquid dispenser that uses a disposable cartridge for the calibration-free dosage of diverse biochemical reagents from the nanoliter to the microliter range. The dispensing system combines the advantages of a positive displacement syringe pump (responsible for defining the aliquot's volume with high accuracy) with a highly dynamic noncontact dispenser (providing kinetic energy to detach the liquid from the tip). The disposable, noncontact dispensing cartridge system renders elaborate washing procedures of tips obsolete. A noncontact sensor monitors the dispensing process to enable an online process control. To further increase confidence and reliability for particularly critical biomedical applications, an optional closed-loop control prevents malfunctions. The dispensing performance was characterized experimentally in the range of 0.25 to 10.0 µL using liquids of different rheological properties (viscosity 1.03-16.98 mPas, surface tension 30.49-70.83 mN/m) without adjusting or calibrating the actuation parameters. The precision ranged between a coefficient of variation of 0.5% and 5.3%, and the accuracy was below ±10%. The presented technology has the potential to contribute significantly to the improvement of biochemical liquid handling for laboratory automation in terms of usability, miniaturization, cost reduction, and safety.

  19. Kinetic investigation for slow combustion of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H.; Yaman, S. [Istanbul Technical Univ., Istanbul (Turkey). Dept. of Chemical Engineering, Faculty of Chemical and Metallurgical Engineering

    2006-07-01

    The renewed interest in biomass as a renewable, clean, and inexpensive fuel was discussed. Many different mechanisms take place simultaneously during biomass combustion and also during other thermal processes such as gasification, pyrolysis or carbonization. These mechanisms have a pronounced influence on the design and operation of thermal conversion processes. In addition, product yields and product distributions from the thermal processes are sensitive to the kinetic properties of biomass. In order to evaluate the combustion mechanisms and the combustion kinetics of biomass, the behavior of these constituents under combustion conditions were properly evaluated. In this study, combustion of biomass samples was carried out in a thermogravimetric analyzer by heating them from ambient to 1173 K with heating rates of 5 K/min and 10 K/min under dynamic dry air atmosphere of 40 mL/min. The biomass samples included olive refuse, sunflower seed shell, rapeseed, grape seed, and hybrid poplar. The purpose of the study was to examine the kinetic properties of biomass during slow combustion for the overall combustion process as well as for some definite temperature intervals at which different combustion mechanisms are present according to the type and complexity of biomass used. Derivative thermogravimetric analysis (DTG) curves were derived, and data obtained from these curves were used to compute the kinetic parameters such as activation energy, pre-exponential factor, and governing mechanisms for the combustion processes. The governing mechanisms for individual temperature intervals were examined along with the overall combustion process. The study showed that at lower temperature intervals, the combustion process was controlled primarily by the chemical reaction. At least 3 sequential mechanisms may occur at different temperature intervals during combustion of biomass. Activation energy and pre-exponential factors were determined for each temperature interval

  20. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Helmich, M.J.; Hoagland, M.C.; Hubbard, R.L.; Schaub, F.S.

    1981-12-22

    A method of combusting natural gas fuel in a two cycle, turbocharged internal combustion engine substantially reduces the production of nitrogen-oxygen emissions. An improved turbocharger design provides increased air charging pressure, produces a controlled lean air/fuel mixture and lowers peak combustion temperatures. A jet cell ignition device ensures uniform, reliable ignition of the lean air/fuel mixture under all operating conditions and the lean air/fuel mixture in turn encourages complete fuel combustion and provides excellent combustion characteristics with methane, ethane and heavier paraffinic hydrocarbon fuels. These structural modifications and adjustment of other operating parameters combine to reduce nitric oxide (NO) and nitrogen dioxide (NO/sub 2/) emissions by as much as 75% while effecting only a negligible increase in fuel consumption.

  1. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-08-17

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  2. A Study of False-Positive and False-Negative Error Rates in Cartridge Case Comparisons

    Science.gov (United States)

    2014-04-07

    Defense Biometrics and Forensics Office, Assistant Secretary of Defense (Research and Engineering), through the U.S. Department of Energy Contract No...official policies, either expressed or implied, of the Defense Biometrics and Forensics Office, Defense Forensic Science Center, or the U.S...Acknowledgements This work was supported by Defense Biometrics and Forensics Office through the U.S. Department of Energy under Contract No. DE-AC02

  3. Reaction-diffusion pulses: a combustion model

    Energy Technology Data Exchange (ETDEWEB)

    Campos, Daniel [Grup de FIsica EstadIstica, Dept. de FIsica, Universitat Autonoma de Barcelona, E-08193 Bellaterrra (Spain); Llebot, Josep Enric [Grup de FIsica EstadIstica, Dept. de FIsica, Universitat Autonoma de Barcelona, E-08193 Bellaterrra (Spain); Fort, Joaquim [Dept. de FIsica, Univ. de Girona, Campus de Montilivi, 17071 Girona, Catalonia (Spain)

    2004-07-02

    We focus on a reaction-diffusion approach proposed recently for experiments on combustion processes, where the heat released by combustion follows first-order reaction kinetics. This case allows us to perform an exhaustive analytical study. Specifically, we obtain the exact expressions for the speed of the thermal pulses, their maximum temperature and the condition of self-sustenance. Finally, we propose two generalizations of the model, namely, the case of several reactants burning together, and that of time-delayed heat conduction. We find an excellent agreement between our analytical results and simulations.

  4. Modeling the internal combustion engine

    Science.gov (United States)

    Zeleznik, F. J.; Mcbride, B. J.

    1985-01-01

    A flexible and computationally economical model of the internal combustion engine was developed for use on large digital computer systems. It is based on a system of ordinary differential equations for cylinder-averaged properties. The computer program is capable of multicycle calculations, with some parameters varying from cycle to cycle, and has restart capabilities. It can accommodate a broad spectrum of reactants, permits changes in physical properties, and offers a wide selection of alternative modeling functions without any reprogramming. It readily adapts to the amount of information available in a particular case because the model is in fact a hierarchy of five models. The models range from a simple model requiring only thermodynamic properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. Among its many features the model includes heat transfer, valve timing, supercharging, motoring, finite burning rates, cycle-to-cycle variations in air-fuel ratio, humid air, residual and recirculated exhaust gas, and full combustion kinetics.

  5. Characteristics of oily sludge combustion in circulating fluidized beds.

    Science.gov (United States)

    Zhou, Lingsheng; Jiang, Xiumin; Liu, Jianguo

    2009-10-15

    Incineration of oily sludge in circulating fluidized beds may be an effective way for its management in some cases. The objective of the present paper is to investigate combustion characteristics of oily sludge, which would be helpful and useful for the design and simulation of a circulating fluidized bed. Firstly, the pyrolysis and combustion of oily sludge were studied through some thermal analyses, which included the thermogravimetric (TG) analysis and the differential thermal analytical (DTA) analysis. It was found that the combustion of oily sludge might be the combustion of its pyrolysis products. Secondly, an experiment for measuring of main components of the volatile from oily sludge pyrolysis was carried out. Some mathematic correlations about the compositions of volatile from oily sludge devolatilization were achieved from the experimental results. Finally, the combustion characteristics of oily sludge was studied in a lab-scale circulating fluidized bed, which could obtain some information about the location of release and combustion of the volatiles.

  6. Ophthalmic viscosurgical device backflow into cartridge during intraocular lens insertion using injectors

    Directory of Open Access Journals (Sweden)

    Matsuura K

    2014-01-01

    Full Text Available Kazuki Matsuura,1 Yoshitsugu Inoue2 1Nojima Hospital, 2Tottori University, Kurayoshi City, Tottori, Japan Background: The purpose of this study was to assess the risk of intraocular contamination caused by intraocular lens (IOL insertion with injectors by observing the dynamics of an ophthalmic viscosurgical device (OVD. Methods: Each type of injector was equipped with a colored OVD and IOL, and a 2 mm length from the tip of the cartridge was replaced with a colored OVD. The various combinations of IOLs and injectors used were: a three-piece shaped IOL, VA60BBR + TypeE1 (HOYA incision size 2.5 mm; group A, n=5; a single-piece IOL, 251+ iSert micro, preloaded (HOYA, incision size 2.2 mm; group G, n=5; and a single-piece IOL, SN6CWS preloaded (Alcon, incision size 2.7 mm; group C, n=5. Results: In group A, the intraocular OVD instantly flowed backward into the injector, whereas the colored OVD was pushed backward deep inside the cartridge without flowing into the eye. In group B, the backflow of the intraocular OVD into the injector was limited, resulting in the influx of a large amount of the colored OVD into the eye along with the IOL. In group C, as in group A, a large amount of the intraocular OVD flowed backward into the injector. Consequently, a small amount of the colored OVD flowed into the eye. Conclusion: The tip of the injector and OVD could be contaminated because the surgical field cannot be completely sterile, even after preoperative disinfection. Our experiments revealed that OVD backflow into the injector cavity occurs during IOL insertion, and this phenomenon may have minimized intraocular contamination. However, small-diameter cartridges along with plate-type haptics allow insufficient OVD backflow, resulting in intraocular influx of the contaminated OVD. Surgeons have to be notified that intraoperative bacterial contamination can occur even after IOL insertion using injectors. Keywords: intraocular lens insertion

  7. Sandia Combustion Research: Technical review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This report contains reports from research programs conducted at the Sandia Combustion Research Facility. Research is presented under the following topics: laser based diagnostics; combustion chemistry; reacting flow; combustion in engines and commercial burners; coal combustion; and industrial processing. Individual projects were processed separately for entry onto the DOE databases.

  8. Liquid rocket combustion chamber acoustic characterization

    Directory of Open Access Journals (Sweden)

    Cândido Magno de Souza

    2010-09-01

    Full Text Available Over the last 40 years, many solid and liquid rocket motors have experienced combustion instabilities. Among other causes, there is the interaction of acoustic modes with the combustion and/or fluid dynamic processes inside the combustion chamber. Studies have been showing that, even if less than 1% of the available energy is diverted to an acoustic mode, combustion instability can be generated. On one hand, this instability can lead to ballistic pressure changes, couple with other propulsion systems such as guidance or thrust vector control, and in the worst case, cause motor structural failure. In this case, measures, applying acoustic techniques, must be taken to correct/minimize these influences on the combustion. The combustion chamber acoustic behavior in operating conditions can be estimated by considering its behavior in room conditions. In this way, acoustic tests can be easily performed, thus identifying the cavity modes. This paper describes the procedures to characterize the acoustic behavior in the inner cavity of four different configurations of a combustion chamber. Simple analytical models are used to calculate the acoustic resonance frequencies and these results are compared with acoustic natural frequencies measured at room conditions. Some comments about the measurement procedures are done, as well as the next steps for the continuity of this research. The analytical and experimental procedures results showed good agreement. However, limitations on high frequency band as well as in the identification of specific kinds of modes indicate that numerical methods able to model the real cavity geometry and an acoustic experimental modal analysis may be necessary for a more complete analysis. Future works shall also consider the presence of passive acoustic devices such as baffles and resonators capable of introducing damping and avoiding or limiting acoustic instabilities.

  9. Detection and genotyping of human papillomavirus in self-obtained cervicovaginal samples by using the FTA cartridge: new possibilities for cervical cancer screening.

    NARCIS (Netherlands)

    Lenselink, C.H.; Bie, R.P. de; Hamont, D. van; Bakkers, J.M.J.E.; Quint, W.G.V.; Massuger, L.F.A.G.; Bekkers, R.L.M.; Melchers, W.J.G.

    2009-01-01

    This study assesses human papillomavirus (HPV) detection and genotyping in self-sampled genital smears applied to an indicating FTA elute cartridge (FTA cartridge). The study group consisted of 96 women, divided into two sample sets. All samples were analyzed by the HPV SPF(10)-Line Blot 25. Set 1

  10. Improving combustion efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Bulsari, A.; Wemberg, A.; Multas, A. [Nonlinear Solutions Oy (Finland)

    2009-06-15

    The paper describes how nonlinear models are used to improve the efficiency of coal combustion while keeping NOx and other emissions under desired limits in the Naantali 2 boiler of Fortum Power and Heat Oy. 16 refs., 6 figs.

  11. Fluidized coal combustion

    Science.gov (United States)

    Moynihan, P. I.; Young, D. L.

    1979-01-01

    Fluidized-bed coal combustion process, in which pulverized coal and limestone are burned in presence of forced air, may lead to efficient, reliable boilers with low sulfur dioxide and nitrogen dioxide emissions.

  12. Modelling diesel combustion

    CERN Document Server

    Lakshminarayanan, P A; Shi, Yu; Reitz, Rolf D

    2010-01-01

    The underlying principles of combustion phenomena are presented here, providing the basis for quantitative evaluation. These phenomena - ignition delay, fuel air mixing, rate of release, etc. - are then modelled for greater understanding and applicability.

  13. TENORM: Coal Combustion Residuals

    Science.gov (United States)

    Burning coal in boilers to create steam for power generation and industrial applications produces a number of combustion residuals. Naturally radioactive materials that were in the coal mostly end up in fly ash, bottom ash and boiler slag.

  14. Antifingerprint property of the hard coat for cartridge-free Blu-ray Disc

    Science.gov (United States)

    Hayashida, Naoki; Itoh, Hidetake; Yoneyama, Kenji; Kato, Tatsuya; Tanaka, Kazushi; Utsunomiya, Hajime

    2003-09-01

    We made improvements on the previously reported hard-coat for cartridge-free Blu-ray disc from a viewpoint of an anti-fingerprint property. As a result of this study, two types of the hard-coat have been obtained. One is for Blu-ray discs of ROM and write-once types, and the other is for that of rewritable type. The former well inhibited a deterioration of bit error rate (bER) of the signal written prior to the fingerprint adhesion. The later exhibited low bER for the data signals written both before and after the fingerprint adhesion. These results are attributable to the area ratio of drops of fingerprint-ingredient on the disc surface, and the low area ratio resulted in a low bER. Moreover, it was confirmed that the disc with higher contact angle of oily compound exhibited the lower area ratio of the fingerprint.

  15. Radiological assessment of cartridge 120-mm, APFSDS-T, XM829 ammunition

    Energy Technology Data Exchange (ETDEWEB)

    Hooker, C.D.; Hadlock, D.E.; Soldat, K.L.; Gilchrist, R.L.

    1983-12-01

    The components of the XM829 round effectively shield out nonpenetrating beta radiation emitted by the depleted uranium; however, photons cna penetrate the components of the round and are therefore the predominant emission. The radiation levels associated with the XM829 ammunition are low. The maximum emissions measured from a cartridge are not likely to result in exposure to military personnel above the maximum permissible nonoccupational dose limits listed in Army Regulation (AR) 40-14. Based upon the specifications contained in 49 CFR 173.424 and the radiation measurement data, the XM829 shipping package may be excepted from the specification packaging, marking and labeling requirements of subpart 49 CFR 173 as long as the outer surface of the uranium is enclosed in an inactive sheath and the conditions specified in 49 CFR 421 (b), (c), and (d) are met.

  16. Thermal spray forming of refractory sample ampoule cartridges for single crystal growth space furnaces

    Science.gov (United States)

    Zimmerman, Frank; Poorman, Richard; Holmes, Richard; Mckechnie, Timothy; Krotz, Phil; Liaw, Yoon

    1993-01-01

    A thermal spray process is being used to build up refractory metals and ceramics into a containment cartridge for high temperature, single crystal semiconductor growth experiments. This process uses high energy plasma inside a low pressure (100-200 torr) inert environment to apply layers of material onto a removable mandrel. A variety of materials are being characterized and evaluated against a demanding set of requirements, including high service temperature (1700 C), oxidation resistance, and resistance to liquid metal attack. Techniques to spray form refractory metals (tungsten, molybdenum, niobium, tantalum) and ceramics (alumina, boron nitride) are being developed in the Plasma Spray Cell at Marshall Space Flight Center. These plasma spray formed materials have been evaluated for mechanical properties, density, microstructure, and resistance to liquid metal attack. Forming techniques and the resultant mechanical and metallurgical properties are presented.

  17. Extraction and PerconcentrationLead (II Using Octadecyl Bonded Silica Cartridge and Determination by FAAS

    Directory of Open Access Journals (Sweden)

    Moghimi A. Shaabanzadeh M.

    2012-01-01

    Full Text Available A simple method has been developed for the preconcentration of Lead (II based on the adsorption of its 1-(2-Pyridyl Azo2-Naphtol (PAN complex on aOctadecyl bonded silica cartridges. The influence of acidity, eluting agents, stability of the column, sample volume and interfering ions has been investigated in detail. The adsorbed complex could be eluted using environmentally benign HNO34M and the concentration of Lead (II was determined flame atomic absorption spectrometry. A detection limit of 50 µgL−1 could be achieved and the developed procedure was successfully applied for the determination of Lead (II in tap water and waste water samples. 

  18. Microscale combustion and power generation

    CERN Document Server

    Cadou, Christopher

    2014-01-01

    Recent advances in microfabrication technologies have enabled the development of entirely new classes of small-scale devices with applications in fields ranging from biomedicine, to wireless communication and computing, to reconnaissance, and to augmentation of human function. In many cases, however, what these devices can actually accomplish is limited by the low energy density of their energy storage and conversion systems. This breakthrough book brings together in one place the information necessary to develop the high energy density combustion-based power sources that will enable many of

  19. Scramjet Combustion Processes

    Science.gov (United States)

    2010-09-01

    plan for these flights is as follows: Scramjet Combustion Processes RTO-EN-AVT-185 11 - 21 HyShot 5 – A Free-Flying Hypersonic Glider HyShot...5 will be a hypersonic glider designed to fly at Mach 8. It will separate from its rocket booster in space and perform controlled manoeuvres as it...RTO-EN-AVT-185 11 - 1 Scramjet Combustion Processes Michael Smart and Ray Stalker Centre for Hypersonics The University of Queensland

  20. Characterization of filter cartridges from the IEA-R1 reactor by radiochemical method

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Bianca; Vicente, Roberto; Ferreira, Robson J.; Goes, Marcos M.; Marumo, Julio T., E-mail: bgeraldo@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    The filter cartridges used in water purification system of research nuclear reactor IEA-R1 are considered radioactive wastes after their useful life. The characterization of these wastes is one of the stages of management, which aims to identify and quantify the radionuclides present, including those known as 'difficult to measure' (DTM) radionuclides. Establish a radiochemical analysis methodology for this type of waste is a difficult job, not only by the application of these techniques, but also by the amount of radionuclides that should be analyzed. In the waste produced in a nuclear reactor, the most important radionuclides are fission products, activation products and transuranic elements. Since these radionuclides emit gamma radiation not measurable in its decay process and consequently are difficult to measure, their concentrations can be estimated by indirect methods such as scale factors. This method is used to evaluate the DTM concentration, which is represented by alpha and beta nuclides using the correlation between them and the radionuclide key, a gamma emitter. The objective of this work is to describe a radiochemical analysis methodology for gamma emitter nuclides, present in the filter cartridges, evaluating the activity and concentrations by destructive assays. At the same time, two studies have been performed by non-destructive assays, the first one based on dose rates and the point kernel method to correlate the results and the second one based on calibration efficiency with Monte Carlo method. These studies belong to the radioactive waste characterization program that has been conducted at the Waste Management Laboratory of Nuclear and Energy Research Institute, IPEN-CNEN/SP. (author)

  1. Sandia Combustion Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, S.C.; Palmer, R.E.; Montana, C.A. (eds.)

    1988-01-01

    During the late 1970s, in response to a national energy crisis, Sandia proposed to the US Department of Energy (DOE) a new, ambitious program in combustion research. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''user facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative-involving US inventories, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions several research projects which have been simulated by working groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship program, supported through the Office of Energy Research, has been instrumental in the success of some of these joint efforts. The remainder of this report presents results of calendar year 1988, separated thematically into eleven categories. Referred journal articles appearing in print during 1988 and selected other publications are included at the end of Section 11. Our traditional'' research activities--combustion chemistry, reacting flows, diagnostics, engine and coal combustion--have been supplemented by a new effort aimed at understanding combustion-related issues in the management of toxic and hazardous materials.

  2. METC Combustion Research Facility

    Energy Technology Data Exchange (ETDEWEB)

    Halow, J.S.; Maloney, D.J.; Richards, G.A.

    1993-11-01

    The objective of the Morgantown Energy Technology Center (METC) high pressure combustion facility is to provide a mid-scale facility for combustion and cleanup research to support DOE`s advanced gas turbine, pressurized, fluidized-bed combustion, and hot gas cleanup programs. The facility is intended to fill a gap between lab scale facilities typical of universities and large scale combustion/turbine test facilities typical of turbine manufacturers. The facility is now available to industry and university partners through cooperative programs with METC. High pressure combustion research is also important to other DOE programs. Integrated gasification combined cycle (IGCC) systems and second-generation, pressurized, fluidized-bed combustion (PFBC) systems use gas turbines/electric generators as primary power generators. The turbine combustors play an important role in achieving high efficiency and low emissions in these novel systems. These systems use a coal-derived fuel gas as fuel for the turbine combustor. The METC facility is designed to support coal fuel gas-fired combustors as well as the natural gas fired combustor used in the advanced turbine program.

  3. Differentiation of coloured inks of inkjet printer cartridges by thin layer chromatography and high performance liquid chromatography.

    Science.gov (United States)

    Poon, N L; Ho, S S H; Li, C K

    2005-01-01

    Document examiners are frequently asked to determine whether or not a colour printout has originated from a particular inkjet printer. The printer can rarely be identified unless some unique defects or irregularities of the printer are present on the printout. However, it is possible to decipher the make and/or model of the printer by comparing the ink-profile of the questioned printout with that of a seized inkjet printer cartridge or from one in a database. This paper presents an overview of a systematic approach to characterising and discriminating the inks of different inkjet printer cartridges using thin layer chromatography (TLC) and high pressure liquid chromatography (HPLC) with multi-wavelength ultra-violet/visible (UV/Vis) detection. Ink samples from 23 different inkjet printer cartridges (including originals and substitutes) of different brands and colour printouts, printed by known printers were examined with newly developed chromatographic methods. Subsequently, a database of the ink-profiles was generated. The methods provide a useful tool for discriminating coloured inks in inkjet printer cartridges of different brands.

  4. Effect of CO Combustion Promoters on Combustion Air Partition in FCC under Nearly Complete Combustion

    Institute of Scientific and Technical Information of China (English)

    王锐; 罗雄麟; 许锋

    2014-01-01

    With CO combustion promoters, the role of combustion air flow rate for concerns of economics and control is important. The combustion air is conceptually divided to three parts:the air consumed by coke burning, the air consumed by CO combustion and the air unreacted. A mathematical model of a fluid catalytic cracking (FCC) unit, which includes a quantitative correlation of CO heterogeneous combustion and the amount of CO combustion promoters, is introduced to investigate the effects of promoters on the three parts of combustion air. The results show that the air consumed by coke burning is almost linear to combustion air flow rate, while the air consumed by CO combustion promoters tends to saturate as combustion air flow rate increases, indicating that higher air flow rate can only be used as a manipulated variable to control the oxygen content for an economic concern.

  5. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Williams, G.J.

    1986-06-03

    A variable power internal combustion engine is described which consists of: a separate air compressor for receiving and compressing a flow of air to a given pressure, the compressor having an inlet valve introducing a flow of air into the compressor and an outlet valve for exhausting compressed air out of the compressor into a compressed air storage means, at least one expander having a cylinder, a cylinder head closing an end of the cylinder, a piston reciprocally mounted in the cylinder for movement away from the cylinder head in a power stroke from an initial position defining a combustion chamber within the cylinder between the cylinder head and the piston, the compressed air storage means receiving the pressurized flow of air from the compressor and being of a volume adequate to provide compressed air in the combustion chamber essentially at the given pressure essentially over the power output of the engine, means for introducing an amount of combustible fuel in the compressed charge to be present with compressed air in the combustion chamber and providing combustion of the amount of fuel in the cylinder with the inlet and exhaust valves closed, cam shaft means in contact with the piston for absorbing and storing the energy of the power stroke of the piston and controlling movement of the piston within the cylinder during the exhaust stroke; the means for varying the volume of the combustion chamber being controlled in accordance with power requirements to provide variable power output and improved efficiency of the engine at power outputs reduced relative to a given design power output of the engine by providing a variable expansion ratio of a minimum of at least about 30 to 1 at the given design power output and higher with reduced power output.

  6. SPONTANEOUS COAL COMBUSTION; MECHANISMS AND PREDICTION.

    Science.gov (United States)

    Herring, James R.; Rich, Fredrick J.

    1983-01-01

    Spontaneous ignition and combustion of coal is a major problem to the coal mining, shipping, and use industries; unintentional combustion causes loss of the resource as well as jeopardy to life and property. The hazard to life is especially acute in the case of underground coal mine fires that start by spontaneous ignition. It is the intention of this research to examine previously suggested causes of spontaneous ignition, to consider new evidence, and to suggest an experimental approach to determine which of these suggested causes is relevant to western U. S. coal. This discussion focuses only on causes and mechanism of spontaneous ignition.

  7. Combustion Behaviour of Advanced Solid Propellants.

    Directory of Open Access Journals (Sweden)

    S. N. Asthana

    1993-07-01

    Full Text Available The study reports the effect of incorporation of Al and ammonium perchlorate (AP individually and in combination with each other on combustion pattern and specific impulse (Isp of minimum signature propellants. Incorporation of Al obviates the combustion instability problems; however, it has marginal effect on burning rates. The composition containing AP and zirconium silicate combination gives superior performance; however, its Isp is considerably lower than the composition incorporating 9 per cent AP. A combination of 6 per cent Al gave 20 per cent enhancement in burning rate and 12 s increase in Isp as compared to purely nitramine-based composition, cal-val results also reveal increase in energy output on incorporating AP and Al. Hot stage microscopic and propellant combustion studies indicate occurrence of intense decomposition reaction in case of AP-based compositions.

  8. Combustible structural composites and methods of forming combustible structural composites

    Science.gov (United States)

    Daniels, Michael A.; Heaps, Ronald J.; Steffler, Eric D; Swank, William D.

    2011-08-30

    Combustible structural composites and methods of forming same are disclosed. In an embodiment, a combustible structural composite includes combustible material comprising a fuel metal and a metal oxide. The fuel metal is present in the combustible material at a weight ratio from 1:9 to 1:1 of the fuel metal to the metal oxide. The fuel metal and the metal oxide are capable of exothermically reacting upon application of energy at or above a threshold value to support self-sustaining combustion of the combustible material within the combustible structural composite. Structural-reinforcing fibers are present in the composite at a weight ratio from 1:20 to 10:1 of the structural-reinforcing fibers to the combustible material. Other embodiments and aspects are disclosed.

  9. Particle Emissions from Biomass Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Szpila, Aneta; Bohgard, Mats [Lund Inst. of Technology (Sweden). Div. of Ergonomics and Aerosol Technology; Strand, Michael; Lillieblad, Lena; Sanati, Mehri [Vaexjoe Univ. (Sweden). Div. of Bioenergy Technology; Pagels, Joakim; Rissler, Jenny; Swietlicki, Erik; Gharibi, Arash [Lund Univ. (Sweden). Div. of Nuclear Physics

    2003-05-01

    particle number concentration increased slightly with increasing load, at the same time the fine mode particles became smaller. This was probably caused by different degree of particle coagulation as the residence time in the boiler was changed. The mean diameter during combustion of forest residue was around 100 nm compared to 70-80 nm for dry wood and pellets, while the total number was close to constant. This explains the differences in mass concentration found in the impactor measurements. The concentrations of CO and THC was highest for the dry wood fuel, the PAH concentration was highest for pellets combustion in boiler 4, however this boiler was poorly tuned at the time of measurement. The PAH concentration was 5 times higher during combustion of dry wood compared to forest residue. The concentration of CO, THC and PAH varied to a great extend. The high concentrations were measured in boilers running at a low load. The concentration of particle organic carbon was less than 15% of PMI for all fuels. However we used heated primary dilution, which inhibits the condensation of organic components into, the particle phase. A significant fraction of the emitted organic carbon may condense to the particle phase during dilution after the stack or after being oxidized in the atmosphere. We also measured elemental carbon in the particle phase. The contribution to PM1 was as high as 25-30% during pellets combustion at low load and 8% at low load during combustion of dry wood. In all other cases the EC-concentration was less than 3% of PMI. PIXE and lon-chromatography confirmed that alkali-salts were the dominant chemical species. PIXE analysis revealed that emitted amounts of heavy metals such as Zn, Cd and Pb are strongly dependent on the type of the fuel used. Forest residues gave high emissions of Zn, Cd and Pb, while pellets gave very high emissions of Cd and Zn. The fuel with the lowest emissions of heavy metals was dry wood. This again could be related to ash content in

  10. Combustion and regulation; Combustion et reglementation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This conference was organized after the publication of the French by-law no 2010 relative to combustion installations and to the abatement of atmospheric pollution. Five topics were discussed during the conference: the new regulations, their content, innovations and modalities of application; the means of energy suppliers to face the new provisions and their schedule; the manufacturers proposals for existing installations and the new equipments; the administration control; and the impact of the new measures on exploitation and engineering. Twenty papers and 2 journal articles are reported in these proceedings. (J.S.)

  11. Emission factors of gaseous carbonaceous species from residential combustion of coal and crop residue briquettes

    Institute of Scientific and Technical Information of China (English)

    Qin WANG; Chunmei GENG; Sihua LU; Wentai CHEN; Min SHAO

    2013-01-01

    Experiments were performed to measure the emission factors (EFs) of gaseous carbonaceous species, such as CO2, CO, CH4, and non-methane volatile organic compounds (NMVOCs), from the combustion of five types of coal of varying organic maturity and two types of biomass briquettes under residential burning conditions. Samples were collected in stainless steel canisters and 2,4- dinitrophenylhydrazine (DNPH) cartridges and were analyzed by GC FID/MS and HPLC, respectively. The EFs from crop residue briquette burning were generally higher than those from coals, with the exception of CO2. The dominant NMVOC species identified in coal smoke were carbonyls (41.7%), followed by C2 unsaturated hydrocarbons (29.1%) and aromatics (12.1%), while C2 unsaturated hydrocarbons were the dominant species (68.9%) emitted from the combustion of crop residue briquettes, followed by aromatics (14.4%). A comparison of burning normal crop residues in stoves and the open field indicated that briquettes emitted a larger proportion of ethene and acetylene. Both combustion efficiency and coal organic maturity had a significant impact on NMVOC EFs from burning coal: NMVOC emissions increased with increasing coal organic maturity but decreased as the combustion efficiency improved. Emissions from the combustion of crop residue briquettes from stoves occurred mainly during the smoldering process, with low combustion efficiency. Therefore, an improved stove design to allow higher combustion efficiency would be beneficial for reducing emissions of carbonaceous air pollutants.

  12. Harmonic components of cylinder pressure variation and their characteristics for combustion noise in internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.R.; Miyamoto, Noboru; Murayama, Tadashi

    1987-10-31

    Combustion noise is a serious problem in internal combustion engines, especially diesel engines. Although the cylinder pressure variation is easily visible tool to evaluate the combustion noise and thermal efficiency, the exciting force in engine combustion noise has not been completely determined. Cylinder pressure variation for different combustion behaviors and their harmonic components were calculated and an attempt was made to correlate the various components. It was found that the logarithmic harmonic components of cylinder pressure variations, the cylinder pressure level (CPL) can be described by a function with four variables, the values of cylinder pressure variation. The results of this paper is summarized as follows: 1) A relationship was established between CPL and four characteristic values describing the cylinder pressure and variation diagram. 2) Harmonic components of cylinder pressure variations are described by a linear function with four variables and four characteristic values. 3) In this case, the coefficients of the four variables depend solely on the order of engine revolutions and are independent of combustion behavior and engine operating conditions. (13 figs, 7 refs)

  13. Studies in combustion dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Koszykowski, M.L. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to develop a fundamental understanding and a quantitative predictive capability in combustion modeling. A large part of the understanding of the chemistry of combustion processes comes from {open_quotes}chemical kinetic modeling.{close_quotes} However, successful modeling is not an isolated activity. It necessarily involves the integration of methods and results from several diverse disciplines and activities including theoretical chemistry, elementary reaction kinetics, fluid mechanics and computational science. Recently the authors have developed and utilized new tools for parallel processing to implement the first numerical model of a turbulent diffusion flame including a {open_quotes}full{close_quotes} chemical mechanism.

  14. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani

    2014-10-01

    Alternative transportation fuels, preferably from renewable sources, include alcohols with up to five or even more carbon atoms. They are considered promising because they can be derived from biological matter via established and new processes. In addition, many of their physical-chemical properties are compatible with the requirements of modern engines, which make them attractive either as replacements for fossil fuels or as fuel additives. Indeed, alcohol fuels have been used since the early years of automobile production, particularly in Brazil, where ethanol has a long history of use as an automobile fuel. Recently, increasing attention has been paid to the use of non-petroleum-based fuels made from biological sources, including alcohols (predominantly ethanol), as important liquid biofuels. Today, the ethanol fuel that is offered in the market is mainly made from sugar cane or corn. Its production as a first-generation biofuel, especially in North America, has been associated with publicly discussed drawbacks, such as reduction in the food supply, need for fertilization, extensive water usage, and other ecological concerns. More environmentally friendly processes are being considered to produce alcohols from inedible plants or plant parts on wasteland. While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides ethanol, many linear and branched members of the alcohol family, from methanol to hexanols, have been studied, with a particular emphasis on butanols. These fuels and their combustion properties, including their ignition, flame propagation, and extinction characteristics, their pyrolysis and oxidation reactions, and their potential to produce pollutant emissions have been intensively investigated in dedicated experiments on the laboratory and the engine scale

  15. Radiative Augmented Combustion.

    Science.gov (United States)

    1985-08-12

    86-0085 In 00I to RADIATIVE AUGMENTED COMBUSTION MOSHE LAVID M.L. ENERGIA , INC. P.O. BOX 1468 1 PRINCETON, NEW JERSEY 08542 AUGUST 1985 *.. plo...Combustion conducted at M.L. ENERGIA . It is funded by the Air Force Office of Scientific Research under Contract No. F49620-83-C-0133, with Dr. J.M...reported. It covers the second year of the contract, from July 15, 1984 through July 14, 1985. The work was performed at ENERGIA , Princeton, New Jersey

  16. Transition nozzle combustion system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Won-Wook; McMahan, Kevin Weston; Maldonado, Jaime Javier

    2016-11-29

    The present application provides a combustion system for use with a cooling flow. The combustion system may include a head end, an aft end, a transition nozzle extending from the head end to the aft end, and an impingement sleeve surrounding the transition nozzle. The impingement sleeve may define a first cavity in communication with the head end for a first portion of the cooling flow and a second cavity in communication with the aft end for a second portion of the cooling flow. The transition nozzle may include a number of cooling holes thereon in communication with the second portion of the cooling flow.

  17. Toxicology of Biodiesel Combustion products

    Science.gov (United States)

    1. Introduction The toxicology of combusted biodiesel is an emerging field. Much of the current knowledge about biological responses and health effects stems from studies of exposures to other fuel sources (typically petroleum diesel, gasoline, and wood) incompletely combusted. ...

  18. On Prevention of Steam Boiler Heating Surface Cartridge Igniter%浅谈蒸汽锅炉受热面爆管的预防

    Institute of Scientific and Technical Information of China (English)

    李宇翔

    2013-01-01

    This article analyzes the causes of steam boiler heating surface cartridge igniter and presents the main points of preventing steam boiler heating surface abrading cartridge igniter and tips for reducing back-end heating surface abrading cartridge igniter.%本文分析了蒸汽锅炉受热面爆管的原因,指出了防止锅炉受热面磨损爆管应注意的要点以及减少尾部受热面磨损爆管应注意的问题。

  19. EXPERIMENT OF THE PERFORMANCE OF HOME-MADE ACTIVATED CARBON FIBRE CARTRIDGE%国产活性炭纤维滤芯性能测试

    Institute of Scientific and Technical Information of China (English)

    万春新; 陈建国; 黄金钟; 胡望钧

    2001-01-01

    本文通过对国产活性炭纤维滤芯与国外进口活性炭纤维滤芯进行的各项性能对比测试结果的分析,指出国产活性炭纤维滤芯可替代国外进口同类产品。%The performance of home-made and import activated carbon fibre cartridge is studied here. By comparing the performances of these two kinds, we found that home-made activated carbon fibre cartridge can be substituted for import activated carbon fibre cartridge of the same kind.

  20. The Influence of Flame Retardant Treated Timber Density on Combustibility

    Directory of Open Access Journals (Sweden)

    Zbignev Karpovič

    2011-04-01

    Full Text Available Timber is widely used as a construction material in the majority of countries. In most cases, timber is the main structural material. Timber and timber fabrics used in building structure elements have to fulfill the requirements of fire safety. This article presents factors affecting the combustibility of timber, mainly the influence of flame retardants on the combustion phase, timber density and moisture. The influence of flame retardant treated timber density on combustibility is analyzed in this paper. Research was performed according to the requirements of the standard LST ISO 5657:1999 “Reaction to fire tests – ignitibility of building products using a radiant heat source”. The influence of flame retardant treated timber density on combustibility is assessed according to duration up to the combustion of the specimen. Article in Lithuanian

  1. Combustion optimization and HCCI modeling for ultra low emission

    Energy Technology Data Exchange (ETDEWEB)

    Koten, Hasan; Yilmaz, Mustafa; Zafer Gul, M. [Marmara University Mechanical Engineering Department (Turkey)], E-mail: hasan.koten@marmara.edu.tr

    2011-07-01

    With the coming shortage of fossil fuels and the rising concerns over the environment it is important to develop new technologies both to reduce energy consumption and pollution at the same time. In the transportation sector, new combustion processes are under development to provide clean diesel combustion with no particulate or NOx emissions. However, these processes have issues such as limited power output, high levels of unburned hydrocarbons, and carbon monoxide emissions. The aim of this paper is to present a methodology for optimizing combustion performance. The methodology consists of the use of a multi-objective genetic algorithm optimization tool; homogeneous charge compression ignition engine cases were studied with the ECFM-3Z combustion model. Results showed that injected fuel mass led to a decrease in power output, a finding which is in keeping with previous research. This paper presented on optimization tool which can be useful in improving the combustion process.

  2. A Statistical Method for Estimating Missing GHG Emissions in Bottom-Up Inventories: The Case of Fossil Fuel Combustion in Industry in the Bogota Region, Colombia

    Science.gov (United States)

    Jimenez-Pizarro, R.; Rojas, A. M.; Pulido-Guio, A. D.

    2012-12-01

    The development of environmentally, socially and financially suitable greenhouse gas (GHG) mitigation portfolios requires detailed disaggregation of emissions by activity sector, preferably at the regional level. Bottom-up (BU) emission inventories are intrinsically disaggregated, but although detailed, they are frequently incomplete. Missing and erroneous activity data are rather common in emission inventories of GHG, criteria and toxic pollutants, even in developed countries. The fraction of missing and erroneous data can be rather large in developing country inventories. In addition, the cost and time for obtaining or correcting this information can be prohibitive or can delay the inventory development. This is particularly true for regional BU inventories in the developing world. Moreover, a rather common practice is to disregard or to arbitrarily impute low default activity or emission values to missing data, which typically leads to significant underestimation of the total emissions. Our investigation focuses on GHG emissions by fossil fuel combustion in industry in the Bogota Region, composed by Bogota and its adjacent, semi-rural area of influence, the Province of Cundinamarca. We found that the BU inventories for this sub-category substantially underestimate emissions when compared to top-down (TD) estimations based on sub-sector specific national fuel consumption data and regional energy intensities. Although both BU inventories have a substantial number of missing and evidently erroneous entries, i.e. information on fuel consumption per combustion unit per company, the validated energy use and emission data display clear and smooth frequency distributions, which can be adequately fitted to bimodal log-normal distributions. This is not unexpected as industrial plant sizes are typically log-normally distributed. Moreover, our statistical tests suggest that industrial sub-sectors, as classified by the International Standard Industrial Classification (ISIC

  3. A new model of repulsive force in eddy current separation for recovering waste toner cartridges.

    Science.gov (United States)

    Ruan, Jujun; Xu, Zhenming

    2011-08-15

    Eddy current separation (ECS) is an efficient method for separating aluminum from plastic in crushed waste toner cartridge (TCs). However, in China, ECS quality of aluminum from plastic is rather low in production practice. Repeating separation even manual sorting is required in the production. Improving separation quality of aluminum has been the pressing problem in the recovery of waste TCs. Furthermore, improving ECS quality can reduce the secondary-pollution (furan and dioxin) brought by plastic in later smelting process for the purification of recovered aluminum. Thus, a new model of repulsive force containing impact factors (machine: B(r), k, R, S(m), B(m); material: S(p), V, γ; and operation: ω(m), v, δ) of the separation process was constructed for guiding the ECS process of waste TCs recovering in this paper. For testing whether the model of repulsive force was suitable to guide the ECS, calculation and experiment of detachment angle of aluminum flake were studied. The calculation results of the detachment angles were agreed with the testing experiment. It indicates that the model is suitable for guiding the ECS of waste TCs recovering. Copyright © 2011 Elsevier B.V. All rights reserved.

  4. Efficient substructure searching of large chemical libraries: the ABCD chemical cartridge.

    Science.gov (United States)

    Agrafiotis, Dimitris K; Lobanov, Victor S; Shemanarev, Maxim; Rassokhin, Dmitrii N; Izrailev, Sergei; Jaeger, Edward P; Alex, Simson; Farnum, Michael

    2011-12-27

    Efficient substructure searching is a key requirement for any chemical information management system. In this paper, we describe the substructure search capabilities of ABCD, an integrated drug discovery informatics platform developed at Johnson & Johnson Pharmaceutical Research & Development, L.L.C. The solution consists of several algorithmic components: 1) a pattern mapping algorithm for solving the subgraph isomorphism problem, 2) an indexing scheme that enables very fast substructure searches on large structure files, 3) the incorporation of that indexing scheme into an Oracle cartridge to enable querying large relational databases through SQL, and 4) a cost estimation scheme that allows the Oracle cost-based optimizer to generate a good execution plan when a substructure search is combined with additional constraints in a single SQL query. The algorithm was tested on a public database comprising nearly 1 million molecules using 4,629 substructure queries, the vast majority of which were submitted by discovery scientists over the last 2.5 years of user acceptance testing of ABCD. 80.7% of these queries were completed in less than a second and 96.8% in less than ten seconds on a single CPU, while on eight processing cores these numbers increased to 93.2% and 99.7%, respectively. The slower queries involved extremely generic patterns that returned the entire database as screening hits and required extensive atom-by-atom verification.

  5. Disposable pen-shaped capillary gel electrophoresis cartridge for fluorescence detection of bio-molecules

    Science.gov (United States)

    Amirkhanian, Varoujan; Tsai, Shou-Kuan

    2014-03-01

    We introduce a novel and cost-effective capillary gel electrophoresis (CGE) system utilizing disposable pen-shaped gelcartridges for highly efficient, high speed, high throughput fluorescence detection of bio-molecules. The CGE system has been integrated with dual excitation and emission optical-fibers with micro-ball end design for fluorescence detection of bio-molecules separated and detected in a disposable pen-shaped capillary gel electrophoresis cartridge. The high-performance capillary gel electrophoresis (CGE) analyzer has been optimized for glycoprotein analysis type applications. Using commercially available labeling agent such as ANTS (8-aminonapthalene-1,3,6- trisulfonate) as an indicator, the capillary gel electrophoresis-based glycan analyzer provides high detection sensitivity and high resolving power in 2-5 minutes of separations. The system can hold total of 96 samples, which can be automatically analyzed within 4-5 hours. This affordable fiber optic based fluorescence detection system provides fast run times (4 minutes vs. 20 minutes with other CE systems), provides improved peak resolution, good linear dynamic range and reproducible migration times, that can be used in laboratories for high speed glycan (N-glycan) profiling applications. The CGE-based glycan analyzer will significantly increase the pace at which glycoprotein research is performed in the labs, saving hours of preparation time and assuring accurate, consistent and economical results.

  6. Microfluidic impact printer with interchangeable cartridges for versatile non-contact multiplexed micropatterning.

    Science.gov (United States)

    Ding, Yuzhe; Huang, Eric; Lam, Kit S; Pan, Tingrui

    2013-05-21

    Biopatterning has been increasingly used for well-defined cellular microenvironment, patterned surface topology, and guided biological cues; however, it meets challenges on biocompatibility, thermal and chemical sensitivity, as well as limited availability of reagents. In this paper, we aim at combining the desired features from non-contact inkjet printing and dot-matrix impact printing to establish a versatile multiplexed micropatterning platform, referred to as Microfluidic Impact Printer (MI-Printer), for emerging biomedical applications. Using this platform, we can achieve the distinct features of no cross-contamination, sub-microliter ink loading with a minimal dead volume, high-throughput printing, biocompatible non-contact processing, sequential patterning with self-alignment, wide adaptability for complex media (e.g., cell suspension or colloidal solutions), interchangeable/disposable cartridge design, and simple assembly and configuration, all highly desirable towards laboratory-based research and development. Specifically, the printing resolution of the MI-printer platform has been experimentally characterized and theoretically analysed. Optimal printing resolution of 80 μm has been repeatedly obtained. Furthermore, two useful functions of the MI-printer, multiplexed printing and combinatorial printing, have been experimentally demonstrated with less than 10 μm misalignment. Moreover, molecular and biological patterning, utilizing the multiplexed and combinatorial printing, has been implemented to illustrate the utility of this versatile printing technique for emerging biomedical applications.

  7. Maintaining accuracy of cellular Yule-Nielsen spectral Neugebauer models for different ink cartridges using principal component analysis.

    Science.gov (United States)

    Wang, Binyu; Xu, Haisong; Luo, M Ronnier; Guo, Jinyi

    2011-07-01

    The replacement of used-up ink cartridges is unavoidable, but it makes the existing characterization model far from accurate, while recharacterization is labor intensive. In this study, we propose a new correction method for cellular Yule-Nielsen spectral Neugebauer (CYNSN) models based on principal component analysis (PCA). First, a small set of correction samples are predicted, printed using new ink cartridges, and then measured. Second, the link between the predicted and measured reflectance weights, generated by PCA, is determined. The experimental results show that the proposed method provides a significant and robust improvement, since not only the color change between original and new inks but also the systemic error of CYNSN modelsis taken into account in the method.

  8. Characterization of Plasma Gun with TiH2/C60 Cartridge for Disruption Mitigation in Tokamaks

    Science.gov (United States)

    Bogatu, I. N.; Thompson, J. R.; Galkin, S. A.; Kim, J. S.; HyperV Technologies Corp. Team

    2011-10-01

    Impurity injection for disruption mitigation in tokamaks must be faster than growth time of plasma instabilities, requires sufficient mass to get critical electron density, high penetrability, and large assimilation fraction in the core plasma, with rapid impurity redistribution over the whole plasma. FAR-TECH, Inc. proposed the innovative idea to use hyper-velocity (>30 km/s), high-density (>1023 m-3) C60/C plasma jets with high ram pressure to deliver the impurity mass in plasma accelerator. We report the complete characterization of the TiH2/C60 cartridge with 5 kJ capacitive driver which demonstrated the capability of producing >30 mg of C60 gas in coaxial plasma gun (~35 cm length) prototype with TiH2/C60 cartridge for a small scale, proof-of-principle experiment on a tokamak. Work supported by the US DOE DE-FG02-08ER85196 grant.

  9. Experimental combustion an introduction

    CERN Document Server

    Mishra, D P

    2014-01-01

    ""… other books available in this area do not cover the detailed topics covered here. Energy and combustion is a hot issue. It is expected to be even hotter with more demand in this area as we search for cleaner methods of energy conversion from chemical to thermal energy.""-Ashwani K. Gupta, Department of Mechanical Engineering, University of Maryland, College Park, USA

  10. Coal combustion research

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C.S.

    1996-06-01

    This section describes research and development related to coal combustion being performed for the Fossil Energy Program under the direction of the Morgantown Energy Technology Center. The key activity involves the application of chaos theory for the diagnosis and control of fossil energy processes.

  11. Optical Tomography in Combustion

    DEFF Research Database (Denmark)

    Evseev, Vadim

    . JQSRT 113 (2012) 2222, 10.1016/j.jqsrt.2012.07.015] included in the PhD thesis as an attachment. The knowledge and experience gained in the PhD project is the first important step towards introducing the advanced optical tomography methods of combustion diagnostics developed in the project to future...

  12. Combustion Models in Finance

    CERN Document Server

    Tannous, C

    2001-01-01

    Combustion reaction kinetics models are used for the description of a special class of bursty Financial Time Series. The small number of parameters they depend upon enable financial analysts to predict the time as well as the magnitude of the jump of the value of the portfolio. Several Financial Time Series are analysed within this framework and applications are given.

  13. Flameless Combustion Workshop

    Science.gov (United States)

    2005-09-20

    operating hours, to produce low emission levels of NOx, CO and UHC . Gas turbine combustion stability has increasingly become a crucial design issue as...achieved proved: "* Safe and reliable operation ofgas turbine combustors "* Low emissions of NO., CO and UHC These results have clear economically

  14. Case study of an MBT plant producing SRF for cement kiln co-combustion, coupled with a bioreactor landfill for process residues.

    Science.gov (United States)

    Grosso, Mario; Dellavedova, Stefano; Rigamonti, Lucia; Scotti, Sergio

    2016-01-01

    The paper describes the performances of the energy recovery pathway from the residual waste based on the production of a Solid Recovered Fuel (SRF) to be exploited via co-combustion in a cement kiln. The SRF is produced in a single stream Mechanical-Biological Treatment plant, where bio-drying of the waste is followed by mechanical refining in order to fulfil the quality requirements by the cement kilns. Peculiar of this MBT is the fact that sorting residues are disposed in a nearby landfill, managed according to a bioreactor approach, where landfill gas is collected for electric energy recovery. A detailed mass and energy balance of the system is presented based on one year operational data, followed by its Life Cycle Assessment. Results show that the system is energetically and environmentally effective, with most of the impacts being more than compensated by the savings of materials and energy. Major role in determining such outcome is the displacement of petcoke in the cement kiln, both in terms of its fossil CO2 emissions and of its life cycle impacts, including the trans-oceanic transport. To check the robustness of the results, two sensitivity analyses are performed on the landfill gas collection efficiency and on the avoided electric energy mix.

  15. Development and Preliminary Assessment of Hemoperfusion Cartridge with Tannic Acid for Toxic Proteins' Precipitation: An In Vitro Model

    Directory of Open Access Journals (Sweden)

    Valquíria Miwa Hanai Yoshida

    2016-09-01

    Full Text Available Charcoal hemoperfusion (CHP is one of the extracorporeal removal techniques that are used to remove toxins from the body. CHP generally is considered the preferred method for extracorporeal extraction of several toxins—toxins that are adsorbed by activated charcoal. Assessments of the tannic acid's protective effects on ophidian poisoning are associated with the toxic proteins' precipitation by tannic acid. The challenge in treating a snakebite lies in removing the injected poison with minimal damage to blood constituent proteins. An alternative is CHP, and this investigation proposed to develop a column for hemoperfuser cartridge, combining charcoal granules trapped between layers of polymeric material conjugated to tannic acid, using an in vitro model scaled to the Wistar rat, which can be tested in an animal model. The cartridge was evaluated using the 22 full factorial design, in duplicate, as a method to study the effects of granulated-charcoal size and tannic acid concentration on the hematologic profile (platelet and leukocyte counts and biochemical profile (total serum protein and albumin dosages of sheep blood. The results demonstrate that charcoal in hemoperfuser cartridge: (1 decreases the serum in sheep blood volume, as consequence, (2 increases the serum proteins' concentration, and (iii exerts slight influence on albumin. The inclusion of tannic acid in hemoperfuser column precipitates some of serum proteins and albumin, decreasing their concentrations in the plasma serum. In conclusion, based on these effects we can suggest the use of 0.02 g tannic acid concentration and 8–20 mesh granulated charcoal in hemoperfuser cartridge for precipitating toxic proteins from snake venoms.

  16. Integration of an Optical Ring Resonator Biosensor into a Self-Contained Microfluidic Cartridge with Active, Single-Shot Micropumps

    Directory of Open Access Journals (Sweden)

    Sascha Geidel

    2016-09-01

    Full Text Available While there have been huge advances in the field of biosensors during the last decade, their integration into a microfluidic environment avoiding external tubing and pumping is still neglected. Herein, we show a new microfluidic design that integrates multiple reservoirs for reagent storage and single-use electrochemical pumps for time-controlled delivery of the liquids. The cartridge has been tested and validated with a silicon nitride-based photonic biosensor incorporating multiple optical ring resonators as sensing elements and an immunoassay as a potential target application. Based on experimental results obtained with a demonstration model, subcomponents were designed and existing protocols were adapted. The newly-designed microfluidic cartridges and photonic sensors were separately characterized on a technical basis and performed well. Afterwards, the sensor was functionalized for a protein detection. The microfluidic cartridge was loaded with the necessary assay reagents. The integrated pumps were programmed to drive the single process steps of an immunoassay. The prototype worked selectively, but only with a low sensitivity. Further work must be carried out to optimize biofunctionalization of the optical ring resonators and to have a more suitable flow velocity progression to enhance the system’s reproducibility.

  17. Regulation of Chandelier Cell Cartridge and Bouton Development via DOCK7-Mediated ErbB4 Activation

    Directory of Open Access Journals (Sweden)

    Yilin Tai

    2014-01-01

    Full Text Available Chandelier cells (ChCs, typified by their unique axonal morphology, are the most distinct interneurons present in cortical circuits. Via their distinctive axonal terminals, called cartridges, these cells selectively target the axon initial segment of pyramidal cells and control action potential initiation; however, the mechanisms that govern the characteristic ChC axonal structure have remained elusive. Here, by employing an in utero electroporation-based method that enables genetic labeling and manipulation of ChCs in vivo, we identify DOCK7, a member of the DOCK180 family, as a molecule essential for ChC cartridge and bouton development. Furthermore, we present evidence that DOCK7 functions as a cytoplasmic activator of the schizophrenia-associated ErbB4 receptor tyrosine kinase and that DOCK7 modulates ErbB4 activity to control ChC cartridge and bouton development. Thus, our findings define DOCK7 and ErbB4 as key components of a pathway that controls the morphological differentiation of ChCs, with implications for the pathogenesis of schizophrenia.

  18. Combustion calorimetry experimental chemical thermodynamics

    CERN Document Server

    Sunner, Stig

    1979-01-01

    Combustion Calorimetry deals with expertise knowledge concerning the calorimetry of combustion reactions of an element or compound. After defining the use of units and physical constants, the book discusses the basic principles of combustion calorimetry and the various instruments and calorimeters used in the experiments to measure operations concerning temperatures and its time variations. One paper discusses the theory and design criteria of combustion calorimeter calibration. Another paper discusses the results obtained from a combustion calorimeter after it has measured the energy or entha

  19. Modelling of CWS combustion process

    Science.gov (United States)

    Rybenko, I. A.; Ermakova, L. A.

    2016-10-01

    The paper considers the combustion process of coal water slurry (CWS) drops. The physico-chemical process scheme consisting of several independent parallel-sequential stages is offered. This scheme of drops combustion process is proved by the particle size distribution test and research stereomicroscopic analysis of combustion products. The results of mathematical modelling and optimization of stationary regimes of CWS combustion are provided. During modeling the problem of defining possible equilibrium composition of products, which can be obtained as a result of CWS combustion processes at different temperatures, is solved.

  20. Time Since Discharge of China-made Type 64 and Type 92 Pistol Cartridges%64式与92式手枪弹的射击时间

    Institute of Scientific and Technical Information of China (English)

    鲍立垠; 周志飞; 王晓琳; 李轶昳; 张刚; 马新和

    2015-01-01

    Estimation of cartridge discharge time is very important for the investigation of same gun-firing related cases. Accompanied with shooting, nitrate gunpowder in cartridges burns and reacts vigorously, while a large series of gaseous and solid reaction compounds are generated and absorbed onto the internal surface of cartridge cases. Experiments were conducted in order to detect the volatile nitrate organic gunshot residues (OGRS) of China-made 7.62 mm type 64 and 9 mm type 92 pistol cartridge cases. After discharged, these two cartridge cases were sampled using solid phase micro-extraction (SPME), and analyzed by gas chromatographic-thermal energy analyzer (GC-TEA).One double peak can be observed in all GC-TEA chromatogram as late as 10 days past discharge. The double peak became weaker along with the time elapsing since discharge. From the discharge time of Day 1 to Day 7, a notable peak was identified in GC-TEA chromatogram of the two cartridge cases in the test time segment from 1 to 2 min. On Day 1, it was merged by one sub-peak of weaker and sharper plus another sub-one of stronger and broader, continuing to be only a peak notably wider, becoming much weaker on Day 9, and eventually hardly seen on Day 11 after discharge. For the first time, the variety curves of the volatile nitrate organic compound content of China-made 7.62 mm type 64 and 9 mm type 92 pistol cartridge cases were developed, and the time since discharge of these two cartridge cases can be estimated.%现代枪弹的发射常伴随着含氮发射药燃烧产生多种气相和固相射击残留物的过程,射击后可挥发的射击残留物附着于弹壳表面,并随时间不断从弹壳内表面逸散。这种逸散过程的量度是估计发射时间的重--素。采用固相微萃取方法对国产64式7.62 mm 手枪弹和92式9 mm 手枪弹进行分析提取,使用气相色谱-热能分析仪分析提取的挥发性含氮有机物。测量含氮有机物相对含量随时间的推

  1. Solid-phase extraction of phosphorous-containing amino acid herbicides from biological specimens with a zirconia-coated silica cartridge.

    Science.gov (United States)

    Watanabe, Daisuke; Ohta, Hikoto; Yamamuro, Tadashi

    2014-10-15

    We report a rapid solid-phase extraction method for glyphosate (Glyp), glufosinate (Gluf), and bialaphos (Bial) using a zirconia-coated silica cartridge, which interacts specifically with phosphorous-containing amino acid herbicides (PAAHs). We extracted PAAHs from serum and urine samples. The PAAHs were derivatized with trimethyl orthoacetate-acetic acid and analyzed by ultra-performance liquid chromatography/tandem mass spectrometry (UPLC-MS/MS). The intra-day and inter-day accuracy was within ±13% RE, the intra-day and inter-day precision was less than 12% RSD, and the total recovery was more than 60% for Glyp and more than 80% for Gluf and Bial. The linearity ranges of the calibration curves of the serum samples were 0.2-10,000μg/mL for Glyp, 0.1-1000μg/L for Gluf, and 0.5-1000μg/L for Bial; and those of the urine samples were 0.4-20,000μg/L for Glyp, 0.2-2000μg/L for Gluf, and 0.1-2000μg/L for Bial. This range covers almost all the reported poisoning cases involving these compounds, from very mild to fatal cases. The present paper offers a universal cleanup method for PAAHs in serum and urine samples for clinical and forensic analysis.

  2. Computational Fluid Dynamics in Combustion

    Directory of Open Access Journals (Sweden)

    P. J. Paul

    2010-10-01

    Full Text Available Computational fluid dynamics has reached a stage where flow field in practical situation can be predicted to aid the design and to probe into the fundamental flow physics to understand and resolve the issues in fundamental fluid mechanics. The study examines the computation of reacting flows. After exploring the conservation equations for species and energy, the methods of closing the reaction rate terms in turbulent flow have been examined briefly. Two cases of computation, where combustion-flow interaction plays important role, have been discussed to illustrate the computational aspects and the physical insight that can be gained by the reacting flow computation.Defence Science Journal, 2010, 60(6, pp.577-582, DOI:http://dx.doi.org/10.14429/dsj.60.600

  3. Simulation study on radiative imaging of combustion flame in furnace

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Radiative imaging of combustion flame in furnace of power plant plays an increasingly important role in combustion diagnosis. This paper presents a new method for calculating the radiative imaging of three-dimensional (3D) combustion flame based on Monte Carlo method and optical lens imaging. Numerical simulation case was used in this study. Radiative images were calculated and images obtained can not only present the energy distribution on the charge-coupled device (CCD) camera target plane but also reflect the energy distribution condition in the simulation furnace. Finally the relationships between volume elements and energy shares were also discussed.

  4. Investigation of the submodels for combustion; Polton osamallien kaeytettaevyys

    Energy Technology Data Exchange (ETDEWEB)

    Kjaeldman, L.; Huttunen, M.; Kyttaelae, J. [VTT Energy, Espoo (Finland)

    1997-10-01

    The capability for numerical analysis of flow, combustion and heat transfer in furnaces has been developed by improving the knowledge of the sensitivity of computed results on submodels recently implemented to the computational environment Ardemus owned by VTT Energy and Imatran Voima Oy. The submodels studied include models for combustion of gaseous (pyrolysed) fuel and for nitric oxide. The cases investigated included a gas flame and pulverized coal and peat combustion in single burner furnaces. The effect of grid refinement on the results was investigated for a corner fired power station furnace. (orig.)

  5. Time Resolved FTIR Analysis of Combustion of Ethanol and Gasoline Combustion in AN Internal Combustion Engine

    Science.gov (United States)

    White, Allen R.; Sakai, Stephen; Devasher, Rebecca B.

    2011-06-01

    In order to pursue In Situ measurements in an internal combustion engine, a MegaTech Mark III transparent spark ignition engine was modified with a sapphire combustion chamber. This modification will allow the transmission of infrared radiation for time-resolved spectroscopic measurements by an infrared spectrometer. By using a Step-scan equipped Fourier transform spectrometer, temporally resolved infrared spectral data were acquired and compared for combustion in the modified Mark III engine. Measurements performed with the FTIR system provide insight into the energy transfer vectors that precede combustion and also provides an in situ measurement of the progress of combustion. Measurements were performed using ethanol and gasoline.

  6. Experimental chemical thermodynamics. Volume I. Combustion calorimetry

    Energy Technology Data Exchange (ETDEWEB)

    Sunner, S.; Mansson, M. (eds.)

    1979-01-01

    This book contains 18 chapters. The information included is: units and physical constants; basic principles of combustion calorimetry; calibration of combustion calorimeters; test and auxiliary substances in combustion calorimetry; strategies in the calculation of standard-state energies of combustion from the experimentally determined quantities; assignments of uncertainties; presentation of combustion calorimetric data in the primary literature; general techniques for combustion of liquid/solid organic compounds by oxygen bomb calorimetry; combustion of liquid/solid organic compounds with non-metallic hetero-atoms; combustion calorimetry of metals and simple metallic compounds; combustion calorimetry of organometallic compounds; combustion in fluorine and other halogens; bomb combustion of gaseous compounds in oxygen; oxygen flame calorimetry; fluorine flame calorimetry; combustion calorimetry as a technological service; trends in combustion calorimetry; and from the history of combustion calorimetry. (DP)

  7. Screening of peptide libraries against protective antigen of Bacillus anthracis in a disposable microfluidic cartridge.

    Directory of Open Access Journals (Sweden)

    Joshua M Kogot

    Full Text Available Bacterial surface peptide display has gained popularity as a method of affinity reagent generation for a wide variety of applications ranging from drug discovery to pathogen detection. In order to isolate the bacterial clones that express peptides with high affinities to the target molecule, multiple rounds of manual magnetic activated cell sorting (MACS followed by multiple rounds of fluorescence activated cell sorting (FACS are conventionally used. Although such manual methods are effective, alternative means of library screening which improve the reproducibility, reduce the cost, reduce cross contamination, and minimize exposure to hazardous target materials are highly desired for practical application. Toward this end, we report the first semi-automated system demonstrating the potential for screening bacterially displayed peptides using disposable microfluidic cartridges. The Micro-Magnetic Separation platform (MMS is capable of screening a bacterial library containing 3 × 10¹⁰ members in 15 minutes and requires minimal operator training. Using this system, we report the isolation of twenty-four distinct peptide ligands that bind to the protective antigen (PA of Bacilus anthracis in three rounds of selection. A consensus motif WXCFTC was found using the MMS and was also found in one of the PA binders isolated by the conventional MACS/FACS approach. We compared MMS and MACS rare cell recovery over cell populations ranging from 0.1% to 0.0000001% and found that both magnetic sorting methods could recover cells down to 0.0000001% initial cell population, with the MMS having overall lower standard deviation of cell recovery. We believe the MMS system offers a compelling approach towards highly efficient, semi-automated screening of molecular libraries that is at least equal to manual magnetic sorting methods and produced, for the first time, 15-mer peptide binders to PA protein that exhibit better affinity and specificity than peptides

  8. {sup 14}CO{sub 2} processing using an improved and robust molecular sieve cartridge

    Energy Technology Data Exchange (ETDEWEB)

    Wotte, Anja, E-mail: Anja.Wotte@uni-koeln.de [Institute of Geology and Mineralogy, University of Cologne, Cologne (Germany); Wordell-Dietrich, Patrick [Thünen Institute of Climate-Smart Agriculture, Braunschweig (Germany); Wacker, Lukas [Ion Beam Physics, ETH Zurich, Zurich (Switzerland); Don, Axel [Thünen Institute of Climate-Smart Agriculture, Braunschweig (Germany); Rethemeyer, Janet [Institute of Geology and Mineralogy, University of Cologne, Cologne (Germany)

    2017-06-01

    Radiocarbon ({sup 14}C) analysis on CO{sub 2} can provide valuable information on the carbon cycle as different carbon pools differ in their {sup 14}C signature. While fresh, biogenic carbon shows atmospheric {sup 14}C concentrations, fossil carbon is {sup 14}C free. As shown in previous studies, CO{sub 2} can be collected for {sup 14}C analysis using molecular sieve cartridges (MSC). These devices have previously been made of plastic and glass, which can easily be damaged during transport. We thus constructed a robust MSC suitable for field application under tough conditions or in remote areas, which is entirely made of stainless steel. The new MSC should also be tight over several months to allow long sampling campaigns and transport times, which was proven by a one year storage test. The reliability of the {sup 14}CO{sub 2} results obtained with the MSC was evaluated by detailed tests of different procedures to clean the molecular sieve (zeolite type 13X) and for the adsorption and desorption of CO{sub 2} from the zeolite using a vacuum rig. We show that the {sup 14}CO{sub 2} results are not affected by any contamination of modern or fossil origin, cross contamination from previous samples, and by carbon isotopic fractionation. In addition, we evaluated the direct CO{sub 2} transfer from the MSC into the automatic graphitization equipment AGE with the subsequent {sup 14}C AMS analysis as graphite. This semi-automatic approach can be fully automated in the future, which would allow a high sample throughput. We obtained very promising, low blank values between 0.0018 and 0.0028 F{sup 14}C (equivalent to 50,800 and 47,200 yrs BP), which are within the analytical background and lower than results obtained in previous studies.

  9. Aerosols from biomass combustion

    Energy Technology Data Exchange (ETDEWEB)

    Nussbaumer, T.

    2001-07-01

    This report is the proceedings of a seminar on biomass combustion and aerosol production organised jointly by the International Energy Agency's (IEA) Task 32 on bio energy and the Swiss Federal Office of Energy (SFOE). This collection of 16 papers discusses the production of aerosols and fine particles by the burning of biomass and their effects. Expert knowledge on the environmental impact of aerosols, formation mechanisms, measurement technologies, methods of analysis and measures to be taken to reduce such emissions is presented. The seminar, visited by 50 participants from 11 countries, shows, according to the authors, that the reduction of aerosol emissions resulting from biomass combustion will remain a challenge for the future.

  10. Combustion: an oil spill mitigation tool

    Energy Technology Data Exchange (ETDEWEB)

    None

    1979-11-01

    The technical feasibility of using combustion as an oil spill mitigation tool was studied. Part I of the two-part report is a practical guide oriented toward the needs of potential users, while Part II is the research or resource document from which the practical guidance was drawn. The study included theoretical evaluations of combustion of petroleum pool fires under the effects of weathering and an oil classification system related to combustion potential. The theoretical analysis of combustion is balanced by practical experience of oil burning and case history information. Decision elements are provided which can be used as a guide for technical evaluations of a particular oil spill situation. The rationale for assessing technical feasibility is given in the context of other alternatives available for response to an oil spill. A series of research and technology development concepts are included for future research. The ethics of using oil burning are discussed as issues, concerns, and tradeoffs. A detailed annotated bibliography is appended along with a capsule review of a decade of oil burning studies and other support information.

  11. Burning characteristics of microcellular combustible objects

    Directory of Open Access Journals (Sweden)

    Wei-tao Yang

    2014-06-01

    Full Text Available Microcellular combustible objects for application of combustible case, caseless ammunition or combustible detonator-holding tubes are fabricated through one-step foaming process, in which supercritical CO2 is used as foaming agent. The formulations consist of inert polymer binder and ultra fine RDX. For the inner porous structures of microcellular combustible objects, the cell sizes present a unimodal or bimodal distribution by adjusting the foaming conditions. Closed bomb test is to investigate the influence of both porous structure style and RDX content on burning behavior. The sample with bimodal distribution of cell sizes burns faster than that with unimodal distribution, and the concentration of RDX can influence the burning characteristics in a positive manner. In addition, the translation of laminar burning to convective burning is determined by burning rate versus pressure curves of samples at two different loading densities, and the resulting transition pressure is 30 MPa. Moreover, the samples with bigger sample size present higher burning rate, resulting in providing deeper convective depth. Dynamic vivacity of samples is also studied. The results show that the vivacity increases with RDX content and varies with inner structure.

  12. Combustion science and engineering

    CERN Document Server

    Annamalai, Kalyan

    2006-01-01

    Introduction and Review of Thermodynamics Introduction Combustion Terminology Matter and Its Properties Microscopic Overview of Thermodynamics Conservation of Mass and Energy and the First Law of Thermodynamics The Second Law of Thermodynamics Summary Stoichiometry and Thermochemistry of Reacting Systems Introduction Overall Reactions Gas Analyses Global Conservation Equations for Reacting Systems Thermochemistry Summary Appendix Reaction Direction and Equilibrium Introduction Reaction Direction and Chemical Equilibrium Chemical Equilibrium Relations Vant Hoff Equation Adi

  13. Combustion Characteristics of Sprays

    Science.gov (United States)

    1989-08-01

    regarded by implication or otherwise, or in any way licensing the holder or any other person or corporation, or conveying any rights or permission to...00 _’N 1. TI TLE inctuat Security CZaaafication5 Combustion Characteristics of Sprays 12. PERSONAL AUTHOR(S) Sohrab, Siavash H. 13& TYPE OF REPORT...to ?!HF of rich butane/air 3unsen flames. .lso, the rotacion speed and :he oerodic temDeracure fluc:uations of rotacfng ?HF are examined. :’!naily

  14. High Gravity (g) Combustion

    Science.gov (United States)

    2006-02-01

    required thrust-to-weight ratio goals. Shorter residence times in the combustion chamber may reduce the NOx emissions, but the CO and UHC emissions then...Emissions analyzing equipment is available to detect CO, CO2, NOx, O2, and total unburned hydrocarbons ( UHC ) at the combustor exit plane. Emissions... UHC ) emissions along with the CO data, as seen in Fig. 24, shows that Configuration 1 had much higher UHC levels. The reactions from hydrocarbons to

  15. Chemical reduction of complex kinetic models of combustion; Reduction chimique des modeles cinetiques complexes de combustion

    Energy Technology Data Exchange (ETDEWEB)

    Fournet, R.; Glaude, P.A.; Warth, V.; Battin-Leclerc, F.; Scacchi, G.; Come, G.M. [Institut National Polytechnique de Lorraine, Ecole Nationale Superieure des Industries Chimiques, CNRS UMR 7630, INPL ENSIC, Dept. de Chimie Physique des Reacteurs, 54 - Nancy (France)

    2001-07-01

    This paper presents an automatized method allowing to notably reduce the size of the primary mechanism of alkane combustion. The free radicals having the same raw formulation and the same functional groups are presented in a global way as a unique species. In this way, the number of radicals can be divided by a factor of 16 in the case of n-heptane combustion. The kinetic parameters linked with the global mechanism are obtained from a weighted average of the kinetic constants of the detailed mechanism, and this without any adjustment.The simulations performed for the combustion mechanisms of the n-heptane and of a mixture of n-heptane and 2,2,3 trimethyl butane are presented in order to show the validity of the proposed method. (J.S.)

  16. Internal combustion engine using premixed combustion of stratified charges

    Science.gov (United States)

    Marriott, Craig D.; Reitz, Rolf D. (Madison, WI

    2003-12-30

    During a combustion cycle, a first stoichiometrically lean fuel charge is injected well prior to top dead center, preferably during the intake stroke. This first fuel charge is substantially mixed with the combustion chamber air during subsequent motion of the piston towards top dead center. A subsequent fuel charge is then injected prior to top dead center to create a stratified, locally richer mixture (but still leaner than stoichiometric) within the combustion chamber. The locally rich region within the combustion chamber has sufficient fuel density to autoignite, and its self-ignition serves to activate ignition for the lean mixture existing within the remainder of the combustion chamber. Because the mixture within the combustion chamber is overall premixed and relatively lean, NO.sub.x and soot production are significantly diminished.

  17. Internal combustion piston engines

    Energy Technology Data Exchange (ETDEWEB)

    Segaser, C.L.

    1977-07-01

    Current worldwide production of internal combustion piston engines includes many diversified types of designs and a very broad range of sizes. Engine sizes range from a few horsepower in small mobile units to over 40,000 brake horsepower in large stationary and marine units. The key characteristics of internal combustion piston engines considered appropriate for use as prime movers in Integrated Community Energy Systems (ICES) are evaluated. The categories of engines considered include spark-ignition gas engines, compression-ignition oil (diesel) engines, and dual-fuel engines. The engines are evaluated with respect to full-load and part-load performance characteristics, reliability, environmental concerns, estimated 1976 cost data, and current and future status of development. The largest internal combustion piston engines manufactured in the United States range up to 13,540 rated brake horsepower. Future development efforts are anticipated to result in a 20 to 25% increase in brake horsepower without increase in or loss of weight, economy, reliability, or life expectancy, predicated on a simple extension of current development trends.

  18. Issues in waste combustion

    Energy Technology Data Exchange (ETDEWEB)

    Gustavsson, Lennart; Robertson, Kerstin; Tullin, Claes [Swedish National Testing and Research Inst., Boraas (Sweden); Sundquist, Lena; Wrangensten, Lars [AaF-Energikonsult AB, Stockholm (Sweden); Blom, Elisabet [AaF-Processdesign AB, Stockholm (Sweden)

    2003-05-01

    The main purpose of this review is to provide an overview of the state-of-the-art on research and development issues related to waste combustion with relevance for Swedish conditions. The review focuses on co-combustion in grate and fluidised bed furnaces. It is primarily literature searches in relevant databases of scientific publications with to material published after 1995. As a complement, findings published in different report series, have also been included. Since the area covered by this report is very wide, we do not claim to cover the issues included completely and it has not been possitile to evaluate the referred studies in depth. Basic knowledge about combustion issues is not included since such information can be found elsewhere in the literature. Rather, this review should be viewed as an overview of research and development in the waste-to-energy area and as such we hope that it will inspire scientists and others to further work in relevant areas.

  19. Development of flameless combustion; Desarrollo de la combustion sin flama

    Energy Technology Data Exchange (ETDEWEB)

    Flores Sauceda, M. Leonardo; Cervantes de Gortari, Jaime Gonzalo [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)]. E-mail: 8344afc@prodigy.net.mx; jgonzalo@servidor.unam.mx

    2010-11-15

    The paper intends contribute to global warming mitigation joint effort that develops technologies to capture the CO{sub 2} produced by fossil fuels combustion and to reduce emission of other greenhouse gases like the NO{sub x}. After reviewing existing combustion bibliography is pointed out that (a) touches only partial aspects of the collective system composed by Combustion-Heat transfer process-Environment, whose interactions are our primary interest and (b) most specialists think there is not yet a clearly winning technology for CO{sub 2} capture and storage. In this paper the study of combustion is focused as integrated in the aforementioned collective system where application of flameless combustion, using oxidant preheated in heat regenerators and fluent gas recirculation into combustion chamber plus appropriated heat and mass balances, simultaneously results in energy saving and environmental impact reduction. [Spanish] El trabajo pretende contribuir al esfuerzo conjunto de mitigacion del calentamiento global que aporta tecnologias para capturar el CO{sub 2} producido por la combustion de combustibles fosiles y para disminuir la emision de otros gases invernadero como NOx. De revision bibliografica sobre combustion se concluye que (a) trata aspectos parciales del sistema compuesto por combustion-proceso de trasferencia de calor-ambiente, cuyas interacciones son nuestro principal interes (b) la mayoria de especialistas considera no hay todavia una tecnologia claramente superior a las demas para captura y almacenaje de CO{sub 2}. Se estudia la combustion como parte integrante del mencionado sistema conjunto, donde la aplicacion de combustion sin flama, empleando oxidante precalentado mediante regeneradores de calor y recirculacion de gases efluentes ademas de los balances de masa y energia adecuados, permite tener simultaneamente ahorros energeticos e impacto ambiental reducido.

  20. Decrease of noxious emissions in the residual fuel oil combustion; Disminucion de emisiones nocivas en la combustion de aceite combustible residual

    Energy Technology Data Exchange (ETDEWEB)

    Mandoki W, Jorge [Econergia S. de R. L. de C. V. Mexico, D. F. (Mexico)

    1994-12-31

    The residual fuel oil combustion emits noxious substances such as carbonaceous particulate, nitrogen oxides, and sulfur trioxide at unacceptable levels. Water emulsified in the fuel substantially reduces such emissions, achieving besides, in most of the cases, a net saving in the fuel consumption. The beneficial effects are shown in burning the residual fuel oil as a water emulsion, as well as the method to produce an adequate emulsion. The emulsified fuel technology offers a low cost option to reduce air pollution. The fuel oil quality has been declining during the last decades due to: 1. Increase in the production of crude heavy oils, generally with higher content of asphaltens and sulfur. 2. Less availability of vacuum distillation residues due to its conversion into greater value products. 3. More intensive conversion processes such as catalytic cracking, visbreaking, etc. that increase the asphaltenes concentration in the bottoms, causing instability problems. 4. The increase in the vanadium and other metals content as the concentration of asphaltenes increases. The use of emulsified fuel oil provides an efficient and economical method to substantially reduce the noxious emissions to the atmosphere. The emulsion contains water particles in a diameter between 2 and 20 microns, uniformly distributed in the fuel oil, generally in a proportion generally of 5 to 10%; besides, it contains a tensioactive agent to assure a stable emulsion capable of withstanding the shearing forces of the pumping and distribution systems. When the atomized oil drops get into the combustion chamber, the emulsified water flashes into high pressure steam, originating a violent secondary atomization. The effect of this secondary atomization is the rupture of the oil drops of various hundred microns, producing drops of 5 to 15 microns in diameter. Since the necessary time for combustion is an exponential function of the drop diameter, a very substantial improvement in the combustion is

  1. Reducing the cost of post combustion capture technology for pulverized coal power plants by flexible operation

    NARCIS (Netherlands)

    Kler, R.C.F. de; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in

  2. Reducing the cost of Post Combustion Capture technology for Pulverized Coal Power Plants by flexible operation

    NARCIS (Netherlands)

    De Kler, R.C.F.; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in

  3. Reducing the cost of Post Combustion Capture technology for Pulverized Coal Power Plants by flexible operation

    NARCIS (Netherlands)

    De Kler, R.C.F.; Verbaan, M.; Goetheer, E.L.V.

    2013-01-01

    Currently the low carbon prices, low Spreads and regulatory uncertainties hampers the business cases for coal-fired power plants with post-combustion capture (PCC) in Europe. Improvement of the business case of coal-fired power plants with post combustion capture requires a different approach in ter

  4. Post combustion in converter steelmaking

    Energy Technology Data Exchange (ETDEWEB)

    Oghbasilasie, H.; Holappa, L.

    1997-12-31

    The purpose of this work is to study the fundamentals of post combustion and the effect of different process parameters on the post combustion ratio (PCR) and heat transfer efficiency (HTE) in converter steelmaking process. The PCR and HTE have been determined under normal operating conditions. Trials assessed the effect of lance height, vessel volume, foaming slag and pellet additions on PCR and HTE. Based on enthalpy considerations, post combustion of CO gas is regarded as one of the most effective means of increasing the heat supply to the BOP. The thermodynamic study of gas-metal-slag reactions gives the limiting conditions for post combustion inside the converter reactor. Different process parameters influencing both thermodynamic equilibria and kinetic conditions can greatly affect the post combustion ratio. Different features of converter processes as well smelting reduction processes utilizing post combustion have been reviewed. (orig.) SULA 2 Research Programme; 26 refs.

  5. Sulfur Chemistry in Combustion I

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Glarborg, Peter

    2000-01-01

    of the sulphur compounds in fossil fuels and the possibilities to remove them will be given. Then the combustion of sulphur species and their influence on the combustion chemistry and especially on the CO oxidation and the NOx formation will be described. Finally the in-situ removal of sulphur in the combustion...... process by reaction between SO2 and calcium containing sorbents and the influence on the NOx chemistry will be treated....

  6. Pulsating combustion - Combustion characteristics and reduction of emissions

    Energy Technology Data Exchange (ETDEWEB)

    Lindholm, Annika

    1999-11-01

    In the search for high efficiency combustion systems pulsating combustion has been identified as one of the technologies that potentially can meet the objectives of clean combustion and good fuel economy. Pulsating combustion offers low emissions of pollutants, high heat transfer and efficient combustion. Although it is an old technology, the interest in pulsating combustion has been renewed in recent years, due to its unique features. Various applications of pulsating combustion can be found, mainly as drying and heating devices, of which the latter also have had commercial success. It is, however, in the design process of a pulse combustor, difficult to predict the operating frequency, the heat release etc., due to the lack of a well founded theory of the phenomenon. Research concerning control over the combustion process is essential for developing high efficiency pulse combustors with low emissions. Natural gas fired Helmholtz type pulse combustors have been the experimental objects of this study. In order to investigate the interaction between the fluid dynamics and the chemistry in pulse combustors, laser based measuring techniques as well as other conventional measuring techniques have been used. The experimental results shows the possibilities to control the combustion characteristics of pulsating combustion. It is shown that the time scales in the large vortices created at the inlet to the combustion chamber are very important for the operation of the pulse combustor. By increasing/decreasing the time scale for the large scale mixing the timing of the heat release is changed and the operating characteristics of the pulse combustor changes. Three different means for NO{sub x} reduction in Helmholtz type pulse combustors have been investigated. These include exhaust gas recirculation, alteration of air/fuel ratio and changed inlet geometry in the combustion chamber. All used methods achieved less than 10 ppm NO{sub x} emitted (referred to stoichiometric

  7. The modes of gaseous combustion

    CERN Document Server

    Rubtsov, Nickolai M

    2016-01-01

    This book provides an analysis of contemporary problems in combustion science, namely flame propagation, detonation and heterophaseous combustion based on the works of the author. The current problems in the area of gas combustion, as well as the methods allowing to calculate and estimate limiting conditions of ignition, and flame propagation on the basis of experimental results are considered. The book focuses on the virtually inaccessible works of Russian authors and will be useful for experienced students and qualified scientists in the area of experimental studies of combustion processes.

  8. Mathematical Modeling in Combustion Science

    CERN Document Server

    Takeno, Tadao

    1988-01-01

    An important new area of current research in combustion science is reviewed in the contributions to this volume. The complicated phenomena of combustion, such as chemical reactions, heat and mass transfer, and gaseous flows, have so far been studied predominantly by experiment and by phenomenological approaches. But asymptotic analysis and other recent developments are rapidly changing this situation. The contributions in this volume are devoted to mathematical modeling in three areas: high Mach number combustion, complex chemistry and physics, and flame modeling in small scale turbulent flow combustion.

  9. Active Combustion Control Valve Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Over the past decade, research into active combustion control has yielded impressive results in suppressing thermoacoustic instabilities and widening the...

  10. Active Combustion Control Valve Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Over the past decade, research into active combustion control has yielded impressive results in suppressing thermoacoustic instabilities and widening the operational...

  11. Basic Aerodynamics of Combustion Chambers,

    Science.gov (United States)

    1981-05-20

    8217, tie imnrulse foree eyuilibr-um c’ the bomd’~ leye - is 173 pv-:irJ p~76vJbK 2sO) IL !-. = Zn pT -- a , bV T. z -,,r y.re C era 3oia * ~~I" onc art-=e...heat by combustion all have very large influences on the capabilities of a combustion chamber. A yellow- colored flame represents diffusion combustion in...the wakes of fuel droplets. Blue- colored flames represent gaseous combustion of evaporated vapors which have already left the fuel droplets. The

  12. Combustion Branch Website Development

    Science.gov (United States)

    Bishop, Eric

    2004-01-01

    The NASA combustion branch is a leader in developing and applying combustion science to focused aerospace propulsion systems concepts. It is widely recognized for unique facilities, analytical tools, and personnel. In order to better communicate the outstanding research being done in this Branch to the public and other research organization, a more substantial website was desired. The objective of this project was to build an up-to-date site that reflects current research in a usable and attractive manner. In order to accomplish this, information was requested from all researchers in the Combustion branch, on their professional skills and on the current projects. This information was used to fill in the Personnel and Research sections of the website. A digital camera was used to photograph all personnel and these photographs were included in the personnel section as well. The design of the site was implemented using the latest web standards: xhtml and external css stylesheets. This implementation conforms to the guidelines recommended by the w3c. It also helps to ensure that the web site is accessible by disabled users, and complies with Section 508 Federal legislation (which mandates that all Federal websites be accessible). Graphics for the new site were generated using the gimp (www.gimp.org) an open-source graphics program similar to Adobe Photoshop. Also, all graphics on the site were of a reasonable size (less than 20k, most less than 2k) so that the page would load quickly. Technologies such as Macromedia Flash and Javascript were avoided, as these only function on some clients which have the proper software installed or enabled. The website was tested on different platforms with many different browsers to ensure there were no compatibility issues. The website was tested on windows with MS IE 6, MSIE 5 , Netscape 7, Mozilla and Opera. On a Mac, the site was tested with MS IE 5 , Netscape 7 and Safari.

  13. Assessing the impact of the dispersion of fuel in case of LOCA; Evaluacion del impacto de la dispersion de combustible en caso de LOCA

    Energy Technology Data Exchange (ETDEWEB)

    Concejal, A.; Garcia Sedano, P. J.; Crespo, A.

    2013-07-01

    Recent studies conducted in Halden and Studsvik have indicated the possibility of obtaining highly fragmented fuel with relatively low temperatures (700 degree centigrade) and high burned (70 MWd / kgU). In case of accident loss of coolant (LOCA), the expulsion may occur outside the pod fuel fragments, which can affect the coolability, cause channel blockade and therefore an increase in the maximum temperature of sheath.

  14. Oxygen isotopic signature of CO2 from combustion processes

    Directory of Open Access Journals (Sweden)

    W. A. Brand

    2011-02-01

    Full Text Available For a comprehensive understanding of the global carbon cycle precise knowledge of all processes is necessary. Stable isotope (13C and 18O abundances provide information for the qualification and the quantification of the diverse source and sink processes. This study focuses on the δ18O signature of CO2 from combustion processes, which are widely present both naturally (wild fires, and human induced (fossil fuel combustion, biomass burning in the carbon cycle. All these combustion processes use atmospheric oxygen, of which the isotopic signature is assumed to be constant with time throughout the whole atmosphere. The combustion is generally presumed to take place at high temperatures, thus minimizing isotopic fractionation. Therefore it is generally supposed that the 18O signature of the produced CO2 is equal to that of the atmospheric oxygen. This study, however, reveals that the situation is much more complicated and that important fractionation effects do occur. From laboratory studies fractionation effects on the order of up to 26%permil; became obvious in the derived CO2 from combustion of different kinds of material, a clear differentiation of about 7‰ was also found in car exhausts which were sampled directly under ambient atmospheric conditions. We investigated a wide range of materials (both different raw materials and similar materials with different inherent 18O signature, sample geometries (e.g. texture and surface-volume ratios and combustion circumstances. We found that the main factor influencing the specific isotopic signatures of the combustion-derived CO2 and of the concomitantly released oxygen-containing side products, is the case-specific rate of combustion. This points firmly into the direction of (diffusive transport of oxygen to the reaction zone as the cause of the isotope fractionation. The original total 18O signature of the material appeared to have little influence, however, a contribution of specific bio

  15. Alternate fuels; Combustibles alternos

    Energy Technology Data Exchange (ETDEWEB)

    Romero Paredes R, Hernando; Ambriz G, Juan Jose [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

    2003-07-01

    In the definition and description of alternate fuels we must center ourselves in those technological alternatives that allow to obtain compounds that differ from the traditional ones, in their forms to be obtained. In this article it is tried to give an overview of alternate fuels to the conventional derivatives of petroleum and that allow to have a clear idea on the tendencies of modern investigation and the technological developments that can be implemented in the short term. It is not pretended to include all the tendencies and developments of the present world, but those that can hit in a relatively short term, in accordance with agreed with the average life of conventional fuels. Nevertheless, most of the conversion principles are applicable to the spectrum of carbonaceous or cellulosic materials which are in nature, are cultivated or wastes of organic origin. Thus one will approach them in a successive way, the physical, chemical and biological conversions that can take place in a production process of an alternate fuel or the same direct use of the fuel such as burning the sweepings derived from the forests. [Spanish] En la definicion y descripcion de combustibles alternos nos debemos centrar en aquellas alternativas tecnologicas que permitan obtener compuestos que difieren de los tradicionales, al menos en sus formas de ser obtenidos. En este articulo se pretende dar un panorama de los combustibles alternos a los convencionales derivados del petroleo y que permita tener una idea clara sobre las tendencias de la investigacion moderna y los desarrollos tecnologicos que puedan ser implementados en el corto plazo. No se pretende abarcar todas las tendencias y desarrollos del mundo actual, sino aquellas que pueden impactar en un plazo relativamente corto, acordes con la vida media de los combustibles convencionales. Sin embargo, la mayor parte de los principios de conversion son aplicables al espectro de materiales carbonaceos o celulosicos los cuales se

  16. Combustion Stratification for Naphtha from CI Combustion to PPC

    KAUST Repository

    Vallinayagam, R.

    2017-03-28

    This study demonstrates the combustion stratification from conventional compression ignition (CI) combustion to partially premixed combustion (PPC). Experiments are performed in an optical CI engine at a speed of 1200 rpm for diesel and naphtha (RON = 46). The motored pressure at TDC is maintained at 35 bar and fuelMEP is kept constant at 5.1 bar to account for the difference in fuel properties between naphtha and diesel. Single injection strategy is employed and the fuel is injected at a pressure of 800 bar. Photron FASTCAM SA4 that captures in-cylinder combustion at the rate of 10000 frames per second is employed. The captured high speed video is processed to study the combustion homogeneity based on an algorithm reported in previous studies. Starting from late fuel injection timings, combustion stratification is investigated by advancing the fuel injection timings. For late start of injection (SOI), a direct link between SOI and combustion phasing is noticed. At early SOI, combustion phasing depends on both intake air temperature and SOI. In order to match the combustion phasing (CA50) of diesel, the intake air temperature is increased to 90°C for naphtha. The combustion stratification from CI to PPC is also investigated for various level of dilution by displacing oxygen with nitrogen in the intake. The start of combustion (SOC) was delayed with the increase in dilution and to compensate for this, the intake air temperature is increased. The mixture homogeneity is enhanced for higher dilution due to longer ignition delay. The results show that high speed image is initially blue and then turned yellow, indicating soot formation and oxidation. The luminosity of combustion images decreases with early SOI and increased dilution. The images are processed to generate the level of stratification based on the image intensity. The level of stratification is same for diesel and naphtha at various SOI. When O concentration in the intake is decreased to 17.7% and 14

  17. Influence of inhibitors on combustion of polyacrylonitrile materials

    Energy Technology Data Exchange (ETDEWEB)

    Vilkova, S.A.; Panova, L.G.; Vilkov, V.A.; Artemenko, S.E.; Vilesova, M.S.

    1983-05-01

    Tris(2,3-dibromopropyl) phosphate is not an effective inhibitor of combustion of PAN fibers or composites based on them; moreover, it increases smoke formation during combustion. The flammability of composite materials (CM) based on PAN fibers is lowered substantially by the use of the bromine-chlorine-phosphorus ternary system. In the case of CM reinforced with synthetic fibers combustion inhibitors incorporated in the reinforcing fibers are more effective than additives introduced into the composite material. The use of fibrous wastes from production of artificial fur, containing chlorine, provides a solution of the problem of their rational utilization in manufacture of combustion-resistant CM, thereby solving the problem of protection of the environment against pollution by polymeric wastes. 5 figures, 1 table.

  18. AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

    Science.gov (United States)

    The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

  19. Path planning during combustion mode switch

    Science.gov (United States)

    Jiang, Li; Ravi, Nikhil

    2015-12-29

    Systems and methods are provided for transitioning between a first combustion mode and a second combustion mode in an internal combustion engine. A current operating point of the engine is identified and a target operating point for the internal combustion engine in the second combustion mode is also determined. A predefined optimized transition operating point is selected from memory. While operating in the first combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion engine to approach the selected optimized transition operating point. When the engine is operating at the selected optimized transition operating point, the combustion mode is switched from the first combustion mode to the second combustion mode. While operating in the second combustion mode, one or more engine actuator settings are adjusted to cause the operating point of the internal combustion to approach the target operating point.

  20. Extraction and Determination of Quercetin and Myricetin from Chamaecyparis obtusa by Ionic Liquids-based Monolithic Cartridge%Extraction and Determination of Quercetin and Myricetin from Chamaecyparis obtusa by Ionic Liquids-based Monolithic Cartridge

    Institute of Scientific and Technical Information of China (English)

    朱涛; 毕文韬; 卢敬昊

    2011-01-01

    A short ionic liquids (ILs)-based monolithic cartridge was prepared and used as the selective extraction sorbent. After the material was evaluated by field emission-scanning electron microscopy (FE-SEM), a new approach for the extraction and determination of quercetin and myricetin from Chamaecyparis obtusa (C. obtusa) by using ILs-based, monolithic cartridge system was developed. Chromatographic analysis was conducted on a C18 column with UV detection at 372 nm, an eluting solution consisting of acetonitrile-water (25/75, V/V) as the mobile phase, and a flow rate of 0.7 mLomin 1. A good linear relationship was demonstrated when the concentrations of quercetin and myricetin were in the range of 0.5--100.0 ggomL-1. The recoveries ranged from 101.6% to 104.6% and the inter- and intra-day relative standard deviations (RSD) were less than 5.0%. This method effectively removed the impurities and avoided tedious pretreatment. It provided a fast, economic and effective method for assaying trace drugs from natural plants.

  1. Theory and modeling in combustion chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J.A.

    1996-10-01

    This paper discusses four important problems in combustion chemistry. In each case, resolution of the problem focuses on a single elementary reaction. Theoretical analysis of this reaction is discussed in some depth, with emphasis on its unusual features. The four combustion problems and their elementary reactions are: (1) Burning velocities, extinction limits, and flammability limits: H+O{sub 2}{leftrightarrow}OH+O, (2) Prompt NO: CH+N{sub 2}{leftrightarrow}HCN+N, (3) the Thermal De-NO{sub x} Process: NH{sub 2}+NO{leftrightarrow}products, and (4) ``Ring`` formation in flames of aliphatic fuels and the importance of resonantly stabilized free radicals: C{sub 3}H{sub 3}{leftrightarrow}products.

  2. Coal char fragmentation during pulverized coal combustion

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, L.L.

    1995-07-01

    A series of investigations of coal and char fragmentation during pulverized coal combustion is reported for a suite of coals ranging in rank from lignite to low-volatile (lv) bituminous coal under combustion conditions similar to those found in commercial-scale boilers. Experimental measurements are described that utilize identical particle sizing characteristics to determine initial and final size distributions. Mechanistic interpretation of the data suggest that coal fragmentation is an insignificant event and that char fragmentation is controlled by char structure. Chars forming cenospheres fragment more extensively than solid chars. Among the chars that fragment, large particles produce more fine material than small particles. In all cases, coal and char fragmentation are seen to be sufficiently minor as to be relatively insignificant factors influencing fly ash size distribution, particle loading, and char burnout.

  3. Up the Technology Readiness Level (TRL) Scale to Demonstrate a Robust, Long Life, Liquid Rocket Engine Combustion Chamber, or...Up the Downstairs

    Science.gov (United States)

    Holmes, Richard; Elam, Sandra; McKechnie, Timothy; Power, Christopher

    2008-01-01

    Advanced vacuum plasma spray (VPS) technology, utilized to successfully apply thermal barrier coatings to space shuttle main engine turbine blades, was further refined as a functional gradient material (FGM) process for space furnace cartridge experiments at 1600 C and for robust, long life combustion chambers for liquid rocket engines. A VPS/FGM 5K (5,000 lb. thrust) thruster has undergone 220 hot firing tests, in pristine condition, showing no wear, blanching or cooling channel cracks. Most recently, this technology has been applied to a 40K thruster, with scale up planned for a 194K Ares I, J-2X engine.

  4. Up the Technology Readiness Level (TRL) Scale to Demonstrate a Robust, Long Life, Liquid Rocket Engine Combustion Chamber, or...Up the Downstairs

    Science.gov (United States)

    Holmes, Richard; Elam, Sandra; McKechnie, Timothy; Power, Christopher

    2008-01-01

    Advanced vacuum plasma spray (VPS) technology, utilized to successfully apply thermal barrier coatings to space shuttle main engine turbine blades, was further refined as a functional gradient material (FGM) process for space furnace cartridge experiments at 1600 C and for robust, long life combustion chambers for liquid rocket engines. A VPS/FGM 5K (5,000 lb. thrust) thruster has undergone 220 hot firing tests, in pristine condition, showing no wear, blanching or cooling channel cracks. Most recently, this technology has been applied to a 40K thruster, with scale up planned for a 194K Ares I, J-2X engine.

  5. 基于MSP430的硒鼓芯片复位装置的设计%Design of Cartridge Chip Reset Device Based on MSP430

    Institute of Scientific and Technical Information of China (English)

    高广; 何美玲; 俎全高; 周敏

    2011-01-01

    Aiming at that the printing supplies for laser toner cartridge manufacturer in the production process are needed to resolve the problem of cartridge chip re-use issues, a cartridge chip reset device based on MSP430 is designed. Different types of toner cartridge chips can be reset by the device, so that the cartridge chips can be recycled in order to achieving production cost savings, protecting the environment. The device also has a good reset effect, the advantages of easy operation.%针对激光打印耗材生产厂家硒鼓生产过程中需对硒鼓芯片进行再利用的问题,设计了一种基于MSP430的硒鼓芯片复位装置.利用该装置可以复位不同型号的硒鼓芯片,从而使硒鼓芯片可循环利用,以达到节约生产成本、保护环境的目的.该装置同时具有复位效果好、易于操作的优点.

  6. Turbulence, combustion, efficiency and emission measurements on a supercharged natural gas SI engine

    Energy Technology Data Exchange (ETDEWEB)

    Einewall, P.; Olsson, Magnus

    1996-08-01

    LDV was used to measure turbulence in six different combustion chambers for a natural gas operated TD102 Volvo truck engine. The efficiency and emissions were measured during supercharged lean operation. The combustion chambers were altered by using pistons with different crown geometries. Some of the load cases require supercharged operation of the engine. The cooling of the cylinder-head was therefore improved. Turbulence, combustion rate, emissions and efficiency was measured for four different piston design. 8 refs, figs

  7. Manifold methods for methane combustion

    Energy Technology Data Exchange (ETDEWEB)

    Yang, B.; Pope, S.B. [Cornell Univ., Ithaca, NY (United States)

    1995-10-01

    Great progresses have been made in combustion research, especially, the computation of laminar flames and the probability density function (PDF) method in turbulent combustion. For one-dimensional laminar flames, by considering the transport mechanism, the detailed chemical kinetic mechanism and the interactions between these two basic processes, today it is a routine matter to calculate flame velocities, extinction, ignition, temperature, and species distributions from the governing equations. Results are in good agreement with those obtained for experiments. However, for turbulent combustion, because of the complexities of turbulent flow, chemical reactions, and the interaction between them, in the foreseeable future, it is impossible to calculate the combustion flow field by directly integrating the basic governing equations. So averaging and modeling are necessary in turbulent combustion studies. Averaging, on one hand, simplifies turbulent combustion calculations, on the other hand, it introduces the infamous closure problems, especially the closure problem with chemical reaction terms. Since in PDF calculations of turbulent combustion, the averages of the chemical reaction terms can be calculated, PDF methods overcome the closure problem with the reaction terms. It has been shown that the PDF method is a most promising method to calculate turbulent combustion. PDF methods have been successfully employed to calculate laboratory turbulent flames: they can predict phenomena such as super equilibrium radical levels, and local extinction. Because of these advantages, PDF methods are becoming used increasingly in industry combustor codes.

  8. Combustion & Laser Diagnostics Research Complex (CLDRC)

    Data.gov (United States)

    Federal Laboratory Consortium — Description: The Combustion and Laser Diagnostics Research Complex (CLRDC) supports the experimental and computational study of fundamental combustion phenomena to...

  9. Decrease of noxious emissions in the residual fuel oil combustion; Disminucion de emisiones nocivas en la combustion de aceite combustible residual

    Energy Technology Data Exchange (ETDEWEB)

    Mandoki W, Jorge [Econergia S. de R. L. de C. V. Mexico, D. F. (Mexico)

    1994-12-31

    The residual fuel oil combustion emits noxious substances such as carbonaceous particulate, nitrogen oxides, and sulfur trioxide at unacceptable levels. Water emulsified in the fuel substantially reduces such emissions, achieving besides, in most of the cases, a net saving in the fuel consumption. The beneficial effects are shown in burning the residual fuel oil as a water emulsion, as well as the method to produce an adequate emulsion. The emulsified fuel technology offers a low cost option to reduce air pollution. The fuel oil quality has been declining during the last decades due to: 1. Increase in the production of crude heavy oils, generally with higher content of asphaltens and sulfur. 2. Less availability of vacuum distillation residues due to its conversion into greater value products. 3. More intensive conversion processes such as catalytic cracking, visbreaking, etc. that increase the asphaltenes concentration in the bottoms, causing instability problems. 4. The increase in the vanadium and other metals content as the concentration of asphaltenes increases. The use of emulsified fuel oil provides an efficient and economical method to substantially reduce the noxious emissions to the atmosphere. The emulsion contains water particles in a diameter between 2 and 20 microns, uniformly distributed in the fuel oil, generally in a proportion generally of 5 to 10%; besides, it contains a tensioactive agent to assure a stable emulsion capable of withstanding the shearing forces of the pumping and distribution systems. When the atomized oil drops get into the combustion chamber, the emulsified water flashes into high pressure steam, originating a violent secondary atomization. The effect of this secondary atomization is the rupture of the oil drops of various hundred microns, producing drops of 5 to 15 microns in diameter. Since the necessary time for combustion is an exponential function of the drop diameter, a very substantial improvement in the combustion is

  10. Mission Success for Combustion Science

    Science.gov (United States)

    Weiland, Karen J.

    2004-01-01

    This presentation describes how mission success for combustion experiments has been obtained in previous spaceflight experiments and how it will be obtained for future International Space Station (ISS) experiments. The fluids and combustion facility is a payload planned for the ISS. It is composed of two racks: the fluids Integrated rack and the Combustion INtegrated Rack (CIR). Requirements for the CIR were obtained from a set of combustion basis experiments that served as surrogates for later experiments. The process for experiments that fly on the ISS includes proposal selection, requirements and success criteria definition, science and engineering reviews, mission operations, and postflight operations. By following this process, the microgravity combustion science program has attained success in 41 out of 42 experiments.

  11. Computational investigation on combustion instabilities in a rocket combustor

    Science.gov (United States)

    Yuan, Lei; Shen, Chibing

    2016-10-01

    High frequency combustion instability is viewed as the most challenging task in the development of Liquid Rocket Engines. In this article, results of attempts to capture the self-excited high frequency combustion instability in a rocket combustor are shown. The presence of combustion instability was demonstrated using point measurements, along with Fast Fourier Transform analysis and instantaneous flowfield contours. A baseline case demonstrates a similar wall heat flux profile as the associated experimental case. The acoustic oscillation modes and corresponding frequencies predicted by current simulations are almost the same as the results obtained from classic acoustic analysis. Pressure wave moving back and forth across the combustor was also observed. Then this baseline case was compared against different fuel-oxidizer velocity ratios. It predicts a general trend: the smaller velocity ratio produces larger oscillation amplitudes than the larger one. A possible explanation for the trend was given using the computational results.

  12. Predicting the lifetime of organic vapor cartridges exposed to volatile organic compound mixtures using a partial differential equations model.

    Science.gov (United States)

    Vuong, François; Chauveau, Romain; Grevillot, Georges; Marsteau, Stéphanie; Silvente, Eric; Vallieres, Cécile

    2016-09-01

    In this study, equilibria, breakthrough curves, and breakthrough times were predicted for three binary mixtures of four volatile organic compounds (VOCs) using a model based on partial differential equations of dynamic adsorption coupling a mass balance, a simple Linear Driving Force (LDF) hypothesis to describe the kinetics, and the well-known Extended-Langmuir (EL) equilibrium model. The model aims to predict with a limited complexity, the BTCs of respirator cartridges exposed to binary vapor mixtures from equilibria and kinetics data obtained from single component. In the model, multicomponent mass transfer was simplified to use only single dynamic adsorption data. The EL expression used in this study predicted equilibria with relatively good accuracy for acetone/ethanol and ethanol/cyclohexane mixtures, but the prediction of cyclohexane uptake when mixed with heptane is less satisfactory. The BTCs given by the model were compared to experimental BTCs to determine the accuracy of the model and the impact of the approximation on mass transfer coefficients. From BTCs, breakthrough times at 10% of the exposure concentration t10% were determined. All t10% were predicted within 20% of the experimental values, and 63% of the breakthrough times were predicted within a 10% error. This study demonstrated that a simple mass balance combined with kinetic approximations is sufficient to predict lifetime for respirator cartridges exposed to VOC mixtures. It also showed that a commonly adopted approach to describe multicomponent adsorption based on volatility of VOC rather than adsorption equilibrium greatly overestimated the breakthrough times.

  13. Evaluation of Different Holder Devices for Freeze-Drying in Dual-Chamber Cartridges With a Focus on Energy Transfer.

    Science.gov (United States)

    Korpus, Christoph; Friess, Wolfgang

    2017-04-01

    For freeze-drying in dual-chamber cartridges, a holder device to enable handling and safe positioning in the freeze-dryer is necessary. The aim of this study was to analyze 4 different types of holder devices and to define the best system based on energy transfer. The main criteria were drying homogeneity, ability to minimize the influence of atypical radiation on product temperatures, and heat transfer effectiveness. The shell holder reduced the influence of atypical radiation by almost 60% compared to a block system and yielded the most homogenous sublimation rates. Besides the most efficient heat transfer with values of 1.58E-4 ± 2.06E-6 cal/(s*cm(2)*K) at 60 mTorr to 3.63E-4 ± 1.85E-5 cal/(s*cm(2)*K) at 200 mTorr for Ktot, reaction times to shelf temperature changes were up to 4 times shorter compared to the other holder systems and even faster than for vials. The flexible holder provided a comparable shielding against atypical radiation as the shell but introduced a third barrier against energy transfer. Block and guardrail holder were the least efficient system tested. Hence, the shell holder provided the best radiation shielding, enhanced the transferability of the results to a larger scale, and improved the homogeneity between the dual-chamber cartridges.

  14. Analysis of the Directional Control Loop Based on Cartridge Valve%二通插装阀方向控制回路分析

    Institute of Scientific and Technical Information of China (English)

    石全

    2009-01-01

    Under the development trend of hydraulic system-High pressure and large flux, the cartridge valve is more and more used. Two kinds of directional control loop composed by the Cartridge Valve are analysed in detail in this paper, that have a positive effect on understanding deeply and appalying of the Cartridge Valve.%高压、大流量是液压系统的发展趋势,二通插装阀的应用势必越来越多.本文对2种比较典型的由插装阀组成的方向控制油路进行了比较细致的分析,对加深理解和实际应用插装阀具有一定的参考价值.

  15. Combined supercritical fluid extraction/solid-phase extraction with octadecylsilane cartridges as a sample preparation technique for the ultratrace analysis of a drug metabolite in plasma.

    Science.gov (United States)

    Liu, H; Cooper, L M; Raynie, D E; Pinkston, J D; Wehmeyer, K R

    1992-04-01

    Supercritical fluid extraction was coupled with solid-phase extraction using octadecylsilane cartridges for the selective isolation of ultratrace levels of a drug metabolite, mebeverine alcohol, from plasma. Plasma was directly applied to the extraction cartridge, the cartridge was washed to remove protein and then extracted under supercritical conditions using CO2/5% methanol. The effluent from the extraction cell was bubbled through a small volume of 2-propanol to trap the extracted mebeverine alcohol. The effects of extraction pressure and temperature on analyte recovery were examined. The absolute recovery, selectivity, precision, and accuracy of the combined supercritical fluid extraction/solid-phase extraction approach were compared to those of conventional solid-phase extraction using gas chromatography/mass spectrometry in the selected-ion monitoring mode. Mebeverine alcohol was used as a model compound, and dog plasma was employed as the biological matrix for these studies.

  16. Time since discharge of 9mm cartridges by headspace analysis, part 2: Ageing study and estimation of the time since discharge using multivariate regression.

    Science.gov (United States)

    Gallidabino, M; Romolo, F S; Weyermann, C

    2017-03-01

    Estimating the time since discharge of spent cartridges can be a valuable tool in the forensic investigation of firearm-related crimes. To reach this aim, it was previously proposed that the decrease of volatile organic compounds released during discharge is monitored over time using non-destructive headspace extraction techniques. While promising results were obtained for large-calibre cartridges (e.g., shotgun shells), handgun calibres yielded unsatisfying results. In addition to the natural complexity of the specimen itself, these can also be attributed to some selective choices in the methods development. Thus, the present series of papers aimed to systematically evaluate the potential of headspace analysis to estimate the time since discharge of cartridges through the use of more comprehensive analytical and interpretative techniques. Following the comprehensive optimisation and validation of an exhaustive headspace sorptive extraction (HSSE) method in the first part of this work, the present paper addresses the application of chemometric tools in order to systematically evaluate the potential of applying headspace analysis to estimate the time since discharge of 9mm Geco cartridges. Several multivariate regression and pre-treatment methods were tested and compared to univariate models based on non-linear regression. Random forests (RF) and partial least squares (PLS) proceeded by pairwise log-ratios normalisation (PLR) showed the best results, and allowed to estimate time since discharge up to 48h of ageing and to differentiate recently fired from older cartridges (e.g., less than 5h compared to more than 1-2 days). The proposed multivariate approaches showed significant improvement compared to univariate models. The effects of storage conditions were also tested and results demonstrated that temperature, humidity and cartridge position should be taken into account when estimating the time since discharge.

  17. The first turbulent combustion

    CERN Document Server

    Gibson, C H

    2005-01-01

    The first turbulent combustion arises in a hot big bang cosmological model Gibson (2004) where nonlinear exothermic turbulence permitted by quantum mechanics, general relativity, multidimensional superstring theory, and fluid mechanics cascades from Planck to strong force freeze out scales with gravity balancing turbulent inertial-vortex forces. Interactions between Planck scale spinning and non-spinning black holes produce high Reynolds number turbulence and temperature mixing with huge Reynolds stresses driving the rapid inflation of space. Kolmogorovian turbulent temperature patterns are fossilized as strong-force exponential inflation stretches them beyond the scale of causal connection ct where c is light speed and t is time. Fossil temperature turbulence patterns seed nucleosynthesis, and then hydro-gravitational structure formation in the plasma epoch, Gibson (1996, 2000). Evidence about formation mechanisms is preserved by cosmic microwave background temperature anisotropies. CMB spectra indicate hydr...

  18. Computational Study of Stratified Combustion in an Optical Diesel Engine

    KAUST Repository

    Jaasim, Mohammed

    2017-03-28

    Full cycle simulations of KAUST optical diesel engine were conducted in order to provide insights into the details of fuel spray, mixing, and combustion characteristics at different start of injection (SOI) conditions. Although optical diagnostics provide valuable information, the high fidelity simulations with matched parametric conditions improve fundamental understanding of relevant physical and chemical processes by accessing additional observables such as the local mixture distribution, intermediate species concentrations, and detailed chemical reaction rates. Commercial software, CONVERGE™, was used as the main simulation tool, with the Reynolds averaged Navier-Stokes (RANS) turbulence model and the multi-zone (SAGE) combustion model to compute the chemical reaction terms. SOI is varied from late compression ignition (CI) to early partially premixed combustion (PPC) conditions. The simulation results revealed a stronger correlation between fuel injection timing and combustion phasing for late SOI conditions, whereas the combustion phasing starts to decouple from SOI for early SOI cases. The predictions are consistent with the experimental observations, in terms of the overall trends in combustion and emission characteristics, while the high fidelity simulations provided further insights into the effects of mixture stratifications resulting from different SOI conditions.

  19. A pore scale study on turbulent combustion in porous media

    Science.gov (United States)

    Jouybari, N. F.; Maerefat, M.; Nimvari, M. E.

    2016-02-01

    This paper presents pore scale simulation of turbulent combustion of air/methane mixture in porous media to investigate the effects of multidimensionality and turbulence on the flame within the pores of porous media. In order to investigate combustion in the pores of porous medium, a simple but often used porous medium consisting of a staggered arrangement of square cylinders is considered in the present study. Results of turbulent kinetic energy, turbulent viscosity ratio, temperature, flame speed, convective heat transfer and thermal conductivity are presented and compared for laminar and turbulent simulations. It is shown that the turbulent kinetic energy increases from the inlet of burner, because of turbulence created by the solid matrix with a sudden jump or reduction at the flame front due to increase in temperature and velocity. Also, the pore scale simulation revealed that the laminarization of flow occurs after flame front in the combustion zone and turbulence effects are important mainly in the preheat zone. It is shown that turbulence enhances the diffusion processes in the preheat zone, but it is not enough to affect the maximum flame speed, temperature distribution and convective heat transfer in the porous burner. The dimensionless parameters associated with the Borghi-Peters diagram of turbulent combustion have been analyzed for the case of combustion in porous media and it is found that the combustion in the porous burner considered in the present study concerns the range of well stirred reactor very close to the laminar flame region.

  20. Micro-fluidic (Lab-on the- Chip) PCR Array Cartridge for Biological Screening in a Hand Held Device: FInal Report for CRADA no 264. PNNL-T2-258-RU with CombiMatrix Corp

    Energy Technology Data Exchange (ETDEWEB)

    Rainina, Evguenia I.

    2010-10-31

    The worldwide emergence of both new and old diseases resulting from human expansion and also human and materials mobility has and will continue to place stress on both medical and clinical diagnostics. The classical approach to bioagents detection involves the use of differential metabolic assays to determine species type in the case of most bacteria, or the use of cell culture and electron microscopy to diagnose viruses and some bacteria that are intracellular parasites. The long-term goal in bioagent detection is to develop a hand-held instrument featuring disposable cartridges which contain all the necessary reagents, reaction chambers, waste chambers, and micro-fluidics to extract, concentrate, amplify, and analyze nucleic acids. This GIPP project began development of a sensory platform using nucleic-acid based probes. Although research was not completed, initial findings indicated that an advanced sensing device could theoretically be built on a DNA/RNA-based technology platform.

  1. Combustion Properties of Straw Briquettes

    Directory of Open Access Journals (Sweden)

    Zhao Qing-ling

    2013-05-01

    Full Text Available The low bulk density of straw is one of the major barriers, which blocks the collection, handling, transportation and storage. Densification of biomass into briquettes/pellets is a suitable method of increasing the bulk density of biomass. Yet in the process, a tremendous amount of air is ejected from biomass grind, which brings substantial specific variation including combustion property. Among them, combustion property is critical for proper design and operation of burning facilities. Therefore, a series of tests about combustion properties of 75mm diameter corn briquettes were done. First, the combustion process (ignition, full flaming and glowing phases., precipitation of tar were investigated by a heating stove, then, Some ash sample from the muffle burner was subjected to an ash melting characteristic test. The results show the combustion of briquettes takes more time than that of raw straw from ignition to complete combustion; in order to meet complete combustion in a short time, the raw straw needs more supply air volume than briquettes under the same α value; the temperature of furnace chamber should been controlled under 900°C, which help to reduce the dark smoke, tar and slag.

  2. Forensic Medical Peculiarities of Skin Damage Caused by a Large-Caliber Bullet Cartridge of Traumatic (Non-Lethal) Action “Teren-12P”

    OpenAIRE

    Sapielkin, V. V.

    2016-01-01

    The limitation of the database on the properties of the bullet cartridge of traumatic (non-lethal) action 12-gauge “Teren-12P” as well as the nature and peculiarities of injuries caused by it can lead to certain difficulties in the conduction of the complex forensic examinations when investigating their wide-scale use. Using pig skin and ballistic clay experimental shots from shotgun “Fort-500M” using bullet cartridge “Teren-12P” from a distance of 15 m were carried out. The obtained data wer...

  3. Catalytic Combustion of Gasified Waste

    Energy Technology Data Exchange (ETDEWEB)

    Kusar, Henrik

    2003-09-01

    This thesis concerns catalytic combustion for gas turbine application using a low heating-value (LHV) gas, derived from gasified waste. The main research in catalytic combustion focuses on methane as fuel, but an increasing interest is directed towards catalytic combustion of LHV fuels. This thesis shows that it is possible to catalytically combust a LHV gas and to oxidize fuel-bound nitrogen (NH{sub 3}) directly into N{sub 2} without forming NO{sub x} The first part of the thesis gives a background to the system. It defines waste, shortly describes gasification and more thoroughly catalytic combustion. The second part of the present thesis, paper I, concerns the development and testing of potential catalysts for catalytic combustion of LHV gases. The objective of this work was to investigate the possibility to use a stable metal oxide instead of noble metals as ignition catalyst and at the same time reduce the formation of NO{sub x} In paper II pilot-scale tests were carried out to prove the potential of catalytic combustion using real gasified waste and to compare with the results obtained in laboratory scale using a synthetic gas simulating gasified waste. In paper III, selective catalytic oxidation for decreasing the NO{sub x} formation from fuel-bound nitrogen was examined using two different approaches: fuel-lean and fuel-rich conditions. Finally, the last part of the thesis deals with deactivation of catalysts. The various deactivation processes which may affect high-temperature catalytic combustion are reviewed in paper IV. In paper V the poisoning effect of low amounts of sulfur was studied; various metal oxides as well as supported palladium and platinum catalysts were used as catalysts for combustion of a synthetic gas. In conclusion, with the results obtained in this thesis it would be possible to compose a working catalytic system for gas turbine application using a LHV gas.

  4. Development of High Efficiency Clean Combustion Engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, Craig; Gonzalez, Manual; Russell, Durrett

    2011-06-30

    This report summarizes activities related to the revised STATEMENT OF PROJECT OBJECTIVES (SOPO) dated June 2010 for the Development of High-Efficiency Clean Combustion engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines (COOPERATIVE AGREEMENT NUMBER DE-FC26-05NT42415) project. In both the spark- (SI) and compression-ignition (CI) development activities covered in this program, the goal was to develop potential production-viable internal combustion engine system technologies that both reduce fuel consumption and simultaneously met exhaust emission targets. To be production-viable, engine technologies were also evaluated to determine if they would meet customer expectations of refinement in terms of noise, vibration, performance, driveability, etc. in addition to having an attractive business case and value. Prior to this activity, only proprietary theoretical / laboratory knowledge existed on the combustion technologies explored The research reported here expands and develops this knowledge to determine series-production viability. Significant SI and CI engine development occurred during this program within General Motors, LLC over more than five years. In the SI program, several engines were designed and developed that used both a relatively simple multi-lift valve train system and a Fully Flexible Valve Actuation (FFVA) system to enable a Homogeneous Charge Compression Ignition (HCCI) combustion process. Many technical challenges, which were unknown at the start of this program, were identified and systematically resolved through analysis, test and development. This report documents the challenges and solutions for each SOPO deliverable. As a result of the project activities, the production viability of the developed clean combustion technologies has been determined. At this time, HCCI combustion for SI engines is not considered production-viable for several reasons. HCCI combustion is excessively sensitive to control variables

  5. Combustion in microgravity: The French contribution

    Science.gov (United States)

    Prud'homme, Roger; Legros, Guillaume; Torero, José L.

    2017-01-01

    Microgravity (drop towers, parabolic flights, sounding rockets and space stations) are particularly relevant to combustion problems given that they show high-density gradients and in many cases weak forced convection. For some configurations where buoyancy forces result in complex flow fields, microgravity leads to ideal conditions that correspond closely to canonical problems, e.g., combustion of a spherical droplet in a far-field still atmosphere, Emmons' problem for flame spreading over a solid flat plate, deflagration waves, etc. A comprehensive chronological review on the many combustion studies in microgravity was written first by Law and Faeth (1994) and then by F.A. Williams (1995). Later on, new recommendations for research directions have been delivered. In France, research has been managed and supported by CNES and CNRS since the creation of the microgravity research group in 1992. At this time, microgravity research and future activities contemplated the following: Droplets: the "D2 law" has been well verified and high-pressure behavior of droplet combustion has been assessed. The studies must be extended in two main directions: vaporization in mixtures near the critical line and collective effects in dense sprays. Flame spread: experiments observed blue flames governed by diffusion that are in accordance with Emmons' theory. Convection-dominated flames showed significant departures from the theory. Some theoretical assumptions appeared controversial and it was noted that radiation effects must be considered, especially when regarding the role of soot production in quenching. Heterogeneous flames: two studies are in progress, one in Poitiers and the other in Marseilles, about flame/suspension interactions. Premixed and triple flames: the knowledge still needs to be complemented. Triple flames must continue to be studied and understanding of "flame balls" still needs to be addressed.

  6. On Lean Turbulent Combustion Modeling

    Directory of Open Access Journals (Sweden)

    Constantin LEVENTIU

    2014-06-01

    Full Text Available This paper investigates a lean methane-air flame with different chemical reaction mechanisms, for laminar and turbulent combustion, approached as one and bi-dimensional problem. The numerical results obtained with Cantera and Ansys Fluent software are compared with experimental data obtained at CORIA Institute, France. First, for laminar combustion, the burn temperature is very well approximated for all chemical mechanisms, however major differences appear in the evaluation of the flame front thickness. Next, the analysis of turbulence-combustion interaction shows that the numerical predictions are suficiently accurate for small and moderate turbulence intensity.

  7. Regulation possibilities of biomass combustion

    Science.gov (United States)

    Suzdalenko, Vera; Gedrovics, Martins; Zake, Maija; Barmina, Inesa

    2012-11-01

    The focus of the recent experimental research is to analyze the regulation possibilities of biomass combustion. Three possibilities were chosen as part of this research: a) biomass cofiring with propane, b) swirling flow with re-circulation zone, and c) use of a permanent magnet. The aim of the research is to provide stable, controllable and effective biomass combustion with minimum emissions. The special pilot device was created where biomass can be combusted separately and co-fired with propane. Wood pellets were used during the experiments.

  8. Combustion-gas recirculation system

    Science.gov (United States)

    Baldwin, Darryl Dean

    2007-10-09

    A combustion-gas recirculation system has a mixing chamber with a mixing-chamber inlet and a mixing-chamber outlet. The combustion-gas recirculation system may further include a duct connected to the mixing-chamber inlet. Additionally, the combustion-gas recirculation system may include an open inlet channel with a solid outer wall. The open inlet channel may extend into the mixing chamber such that an end of the open inlet channel is disposed between the mixing-chamber inlet and the mixing-chamber outlet. Furthermore, air within the open inlet channel may be at a pressure near or below atmospheric pressure.

  9. THE COMBUSTION ACTION VERIFICATION AND ESTIMATE OF COMBUSTION EFFICIENCY IN AVIATION GAS#TURBINE ENGINE COMBUSTION CHAMBERS

    OpenAIRE

    2011-01-01

    Verification results of combustion action simulating and estimate of calculation combustion efficiency that was given by simulating were shown. Mathematical model and its assumption are described. Execution calculations method was shown. Results of simulating are shown; their comparative analyses with results of experiment were executed. Accuracy of combustion action mathematical modeling by combustion efficiency in model with oneand two-stage reactions of combustion was estimated. The infere...

  10. Measures for a quality combustion (combustion chamber exit and downstream); Mesures pour une combustion de qualite (sortie de chambre de combustion et en aval)

    Energy Technology Data Exchange (ETDEWEB)

    Epinat, G. [APAVE Lyonnaise, 69 (France)

    1996-12-31

    After a review of the different pollutants related to the various types of stationary and mobile combustion processes (stoichiometric, reducing and oxidizing combustion), measures and analyses than may be used to ensure the quality and efficiency of combustion processes are reviewed: opacimeters, UV analyzers, etc. The regulation and control equipment for combustion systems are then listed, according to the generator capacity level

  11. Computational Modeling of Turbulent Spray Combustion

    NARCIS (Netherlands)

    Ma, L.

    2016-01-01

    The objective of the research presented in this thesis is development and validation of predictive models or modeling approaches of liquid fuel combustion (spray combustion) in hot-diluted environments, known as flameless combustion or MILD combustion. The goal is to combine good physical insight,

  12. Computational Modeling of Turbulent Spray Combustion

    NARCIS (Netherlands)

    Ma, L.

    2016-01-01

    The objective of the research presented in this thesis is development and validation of predictive models or modeling approaches of liquid fuel combustion (spray combustion) in hot-diluted environments, known as flameless combustion or MILD combustion. The goal is to combine good physical insight, a

  13. Combustion Process Modelling and Control

    Directory of Open Access Journals (Sweden)

    Vladimír Maduda

    2007-10-01

    Full Text Available This paper deals with realization of combustion control system on programmable logic controllers. Control system design is based on analysis of the current state of combustion control systems in technological device of raw material processing area. Control system design is composed of two subsystems. First subsystem is represented by software system for measured data processing and for data processing from simulation of the combustion mathematical model. Outputs are parameters for setting of controller algorithms. Second subsystem consists from programme modules. The programme module is presented by specific control algorithm, for example proportional regulation, programmed proportional regulation, proportional regulation with correction on the oxygen in waste gas, and so on. According to the specific combustion control requirements it is possible built-up concrete control system by programme modules. The programme modules were programmed by Automation studio that is used for development, debugging and testing software for B&R controllers.

  14. Putting combustion optimization to work

    Energy Technology Data Exchange (ETDEWEB)

    Spring, N.

    2009-05-15

    New plants and plants that are retrofitting can benefit from combustion optimization. Boiler tuning and optimization can complement each other. The continuous emissions monitoring system CEMS, and tunable diode laser absorption spectroscopy TDLAS can be used for optimisation. NeuCO's CombustionOpt neural network software can determine optimal fuel and air set points. Babcock and Wilcox Power Generation Group Inc's Flame Doctor can be used in conjunction with other systems to diagnose and correct coal-fired burner performance. The four units of the Colstrip power plant in Colstrips, Montana were recently fitted with combustion optimization systems based on advanced model predictive multi variable controls (MPCs), ABB's Predict & Control tool. Unit 4 of Tampa Electric's Big Bend plant in Florida is fitted with Emerson's SmartProcess fuzzy neural model based combustion optimisation system. 1 photo.

  15. Flameless Combustion for Gas Turbines

    Science.gov (United States)

    Gutmark, Ephraim; Li, Guoqiang; Overman, Nick; Cornwell, Michael; Stankovic, Dragan; Fuchs, Laszlo; Milosavljevic, Vladimir

    2006-11-01

    An experimental study of a novel flameless combustor for gas turbine engines is presented. Flameless combustion is characterized by distributed flame and even temperature distribution for high preheat air temperature and large amount of recirculating low oxygen exhaust gases. Extremely low emissions of NOx, CO, and UHC are reported. Measurements of the flame chemiluminescence, CO and NOx emissions, acoustic pressure, temperature and velocity fields as a function of the preheat temperature, inlet air mass flow rate, exhaust nozzle contraction ratio, and combustor chamber diameter are described. The data indicate that larger pressure drop promotes flameless combustion and low NOx emissions at the same flame temperature. High preheated temperature and flow rates also help in forming stable combustion and therefore are favorable for flameless combustion.

  16. Effects of combustible stacking in large compartments

    DEFF Research Database (Denmark)

    Gentili, Filippo; Giuliani, Luisa; Bontempi, Franco

    2013-01-01

    of non uniform distribution of the combustible materials and fire propagation. These aspects are discussed in this paper with reference to an industrial steel building, taken as case study. Fires triggered by the burning of wooden pallets stored in the premises have been investigated with respect...... to different stacking configurations of the pallets with the avail of a CFD code. The results in term of temperatures of the hot gasses and of the steel elements composing the structural system are compared with simplified analytical model of localized and post-flashover fires, with the aim of highlighting...

  17. Large eddy simulation modelling of combustion for propulsion applications.

    Science.gov (United States)

    Fureby, C

    2009-07-28

    Predictive modelling of turbulent combustion is important for the development of air-breathing engines, internal combustion engines, furnaces and for power generation. Significant advances in modelling non-reactive turbulent flows are now possible with the development of large eddy simulation (LES), in which the large energetic scales of the flow are resolved on the grid while modelling the effects of the small scales. Here, we discuss the use of combustion LES in predictive modelling of propulsion applications such as gas turbine, ramjet and scramjet engines. The LES models used are described in some detail and are validated against laboratory data-of which results from two cases are presented. These validated LES models are then applied to an annular multi-burner gas turbine combustor and a simplified scramjet combustor, for which some additional experimental data are available. For these cases, good agreement with the available reference data is obtained, and the LES predictions are used to elucidate the flow physics in such devices to further enhance our knowledge of these propulsion systems. Particular attention is focused on the influence of the combustion chemistry, turbulence-chemistry interaction, self-ignition, flame holding burner-to-burner interactions and combustion oscillations.

  18. Combustion of boron containing compositions

    Energy Technology Data Exchange (ETDEWEB)

    Frolov, Y.; Pivkina, A. [Institute of Chemical Physics, Russian Academy of Science, Moscow (Russian Federation)

    1996-12-31

    Boron is one of the most energetic components for explosives, propellants and for heterogeneous condensed systems in common. The combustion process of mixtures of boron with different oxidizers was studied. The burning rate, concentration combustion limits, the agglomeration and dispersion processes during reaction wave propagation were analysed in the respect of the percolation theory. The linear dependence of the burning rate on the contact surface value was demonstrated. The percolative model for the experimental results explanation is proposed. (authors) 5 refs.

  19. Smoldering Combustion Experiments in Microgravity

    Science.gov (United States)

    Walther, David C.; Fernandez-Pello, A. Carlos; Urban, David L.

    1997-01-01

    The Microgravity Smoldering Combustion (MSC) experiment is part of a study of the smolder characteristics of porous combustible materials in a microgravity environment. Smoldering is a non-flaming form of combustion that takes place in the interior of porous materials and takes place in a number of processes ranging from smoldering of porous insulation materials to high temperature synthesis of metals. The objective of the study is to provide a better understanding of the controlling mechanisms of smolder, both in microgravity and normal-gravity. As with many forms of combustion, gravity affects the availability of oxidizer and transport of heat, and therefore the rate of combustion. Microgravity smolder experiments, in both a quiescent oxidizing environment, and in a forced oxidizing flow have been conducted aboard the NASA Space Shuttle (STS-69 and STS-77 missions) to determine the effect of the ambient oxygen concentration and oxidizer forced flow velocity on smolder combustion in microgravity. The experimental apparatus is contained within the NASA Get Away Special Canister (GAS-CAN) Payload. These two sets of experiments investigate the propagation of smolder along the polyurethane foam sample under both diffusion driven and forced flow driven smoldering. The results of the microgravity experiments are compared with identical ones carried out in normal gravity, and are used to verify present theories of smolder combustion. The results of this study will provide new insights into the smoldering combustion process. Thermocouple histories show that the microgravity smolder reaction temperatures (Ts) and propagation velocities (Us) lie between those of identical normal-gravity upward and downward tests. These observations indicate the effect of buoyancy on the transport of oxidizer to the reaction front.

  20. Sensitive determination of fenpropathrin, cyhalothrin and deltamethrin in environmental water samples using multiwalled carbon nanotubes cartridge prior to HPLC

    Institute of Scientific and Technical Information of China (English)

    Qing Xiang Zhou; Guo Hong Xie; Jun Ping Xiao; Wei Dong Wang; Yu Jie Ding

    2008-01-01

    This paper described a new method for the trace determination of fenpropathrin, cyhalothrin and deltamethrin using multiwalledcarbon nanotubes (MWCNTs) cartridge. Important parameters, such as the sample pH, eluent and its volume, sample flow rate andsample volume were investigated in detail. The linear ranges, the detection limits, and precisions (R.S.D.) were in the range of 0.1-40 μg L-1 1.3-4.3 ng L-1 and 2.3-2.8%, respectively. The performance of the proposed method was validated with real watersamples, and the spiked recoveries were in the range of 91.7-117.8%, respectively. The experimental results demonstrated that theproposed method was an excellent alternative for the routine analysis of such pollutants in environmental samples.

  1. Environmental impacts and resource losses of incinerating misplaced household special wastes (WEEE, batteries, ink cartridges and cables)

    DEFF Research Database (Denmark)

    Bigum, Marianne Kristine Kjærgaard; Damgaard, Anders; Scheutz, Charlotte

    2017-01-01

    the misplaced special waste is only 0.5% of residual household waste, it constitutes in the residual household waste the most significant fraction with respect to metal content when iron and aluminum are excluded. By extending the boundary of the LCA beyond the traditional “zero burden boundary”, we were able......The contribution of misplaced special waste (sWEEE, lamps, CRT, batteries, ink cartridges and cables) to environmental impacts from incineration of residual household waste was quantified through life cycle assessment (LCA)-modelling. Misplaced special waste was quantified to constitute less than 1...... and batteries. However as shown by sensitivity analysis, lack of good data on the transfer of rare and hazardous metals to the flue gas in the incineration process should receive further investigation before the environmental impacts from misplaced incinerated special waste can fully be concluded upon. Although...

  2. Rotary internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Witkowski, J.

    1989-12-05

    This patent describes an internal combustion engine assembly. It includes: a central rotor means formed with at least one peripheral fuel cavity. The cavity having a first surface defining a thrust surface and a second surface defining a contoured surface; a housing means enclosing the rotor and having an internal wall encircling the rotor. The internal wall being intercepted by at least two recesses defining cylinder means. The housing means and the rotor means being relatively rotatable; piston means individual to each the cylinder means and reciprocable therein; each piton means having a working face complementary to aid contoured surface; and power means for urging the working face into intimate areal contact with the contoured surface to create a first seal means. The housing means having at lest one fuel inlet port, at least one fuel ignition means and at least one exhaust port whereby during the course of a revolution of the rotor means relative to the housing means, the first seal means, the power means, the respective ports, the ignition means and the fuel cavity cooperate to develop fuel compression, fuel ignition and exhaust functions.

  3. Internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Laskaris, M.A.; Broitman, K.; Natale, S.E.

    1991-08-27

    This patent describes improvement in a two-stroke internal combustion engine adapted to run on a diesel or a kerosene type of fuel, and including a piston connected to the crankshaft of the engine to move within a cylinder through a first stroke from a top dead center position to a bottom dead center position and through a second stroke from the bottom dead center position back to the top dead center position. The improvement comprises: means providing a cylinder head at the top end of the engine cylinder in the shape of an open bowl having a generally cup-shaped configuration including a sidewall portion, a spark plug positioned centrally within the bowl at the top end of the cylinder, and means for injecting fuel into the top end of the engine cylinder at a location between the spark plug and the sidewall portion, the fuel injecting means including an injection nozzle having a plurality of nozzle openings therein, the nozzle openings being constructed and arranged to discharge a plurality of plume-like sprays into the top end of the cylinder at a location within the bowl, two of the sprays being directed from the nozzle to diverge and pass along opposite sides of the spark plug, and additional sprays being directed from the nozzle against the sidewall portion or the cylinder head to be deflected therefrom back toward the piston and the spark plug to thereby form a cloud of fuel over the spark plug for good ignition.

  4. Efficiency of Polyphenol Extraction from Artificial Honey Using C18 Cartridges and Amberlite® XAD-2 Resin: A Comparative Study

    Directory of Open Access Journals (Sweden)

    Chua Yung An

    2016-01-01

    Full Text Available A comparative study of the extraction efficiency of nine known polyphenols [phenolic acids (benzoic acid, dihydroxybenzoic acid, gallic acid, trans-cinnamic acid, and vanillic acid and flavonoids (naringenin, naringin, quercetin, and rutin] was conducted by deliberately adding the polyphenols to an artificial honey solution and performing solid phase extraction (SPE. Two SPE methods were compared: one using Amberlite XAD-2 resin and another one using a C18 cartridge. A gradient high performance liquid chromatography system with an RP18 column and photodiode array detector was utilized to analyze the extracted polyphenols. The mean percent of recovery from the C18 cartridges was 74.2%, while that from the Amberlite XAD-2 resin was 43.7%. The recoveries of vanillic acid, naringin, and rutin were excellent (>90%; however, gallic acid was not obtained when C18 cartridges were used. Additionally, the reusability of Amberlite XAD-2 resin was investigated, revealing that the mean recovery of polyphenols decreased from 43.7% (1st extraction to 29.3% (3rd extraction. It was concluded that although Amberlite XAD-2 resin yielded a higher number of compounds, C18 cartridges gave a better extraction recovery. The lower recovery seen for the Amberlite XAD-2 resin also cannot be compensated by repeated extractions due to the gradual decrease of extraction recovery when reused.

  5. First experiences with 2D-mXRF analysis of gunshot residue on garment, tissue, and cartridge cases

    Science.gov (United States)

    Knijnenberg, Alwin; Stamouli, Amalia; Janssen, Martin

    2014-09-01

    The investigation of garment and human tissue originating from a victim of a shooting incident can provide crucial information for the reconstruction of such an incident. The use of 2D-mXRF for such investigations has several advantages over current methods as this new technique can be used to scan large areas, provides simultaneous information on multiple elements, can be applied under ambient conditions and is non-destructive. In this paper we report our experiences and challenges with the implementation of 2D-mXRF in GSR analysis. Currently we mainly focus on the use of 2D-mXRF as a tool for visualizing elemental distributions on various samples.

  6. Steady-state hydrazinium nitroformate (HNF) combustion modeling

    NARCIS (Netherlands)

    Louwers, J.; Gadiot, G.M.H.J.L.; Brewster, M.Q.; Son, S.F.; Parr, T.; Hanson-Parr, D.

    1999-01-01

    Two simplified modeling approaches are used to model the combustion of hydrazinium nitroformate (HNF), N2H5·C(NO2)3. The condensed phase is treated by high-activation-energy asymptotics. The gas phase is treated by two limit cases: the classical high-activation-energy approximation and the recently

  7. Effects of MTBE blended diesel fuel on diesel combustion and emissions; MTBE kongo keiyu ga diesel nensho haiki ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Shundo, S.; Yokota, H.; Kakegawa, T. [Hino Motors, Ltd., Tokyo (Japan)

    1997-10-01

    The effects of MTBE (Methyl-t-butyl ether) blended diesel fuel on diesel combustion and emissions were studied. In conventional diesel combustion, the testing mode was carried out in conformity with the Japanese 13 mode. Furthermore, this fuel was applied to a new combustion system (Homogeneous Charge Intelligent Multiple Injection). MTBE blended diesel fuel is more effective in the case of new combustion system and very low NOx, PM capability is suggested. 6 refs., 6 figs., 2 tabs.

  8. Co-combustion and gasification of various biomasses

    Energy Technology Data Exchange (ETDEWEB)

    Mutanen, K. [A. Ahlstrom Corporation, Varkaus (Finland). Ahlstrom Pyropower

    1996-12-31

    During the last twenty years the development of fluidized bed combustion and gasification technology has made it possible to increase significantly utilisation of various biomasses in power and heat generation. The forerunner was the pulp and paper industry that has an adequate biomass fuel supply and energy demand on site. Later on municipalities and even utilities have seen biomass as a potential fuel. The range of available biomasses includes wood-based fuels and wastes like bark, wood chips, and saw dust, agricultural wastes like straw, olive waste and rice husk, sludges from paper mills and de-inking plants, other wastes like municipal sludges, waste paper and RDF. Recently new environmental regulations and taxation of fossil fuels have further increased interest in the use of biomasses in energy generation. However, in many cases available quantities and/or qualities of biomasses are not adequate for only biomass-based energy generation in an economic sense. On the other hand plant owners want to maintain a high level of fuel flexibility and fuel supply security. In some cases disposing by burning is the only feasible way to handle certain wastes. In many cases the only way to fulfil these targets and utilize the energy is to apply co-combustion or gasification of different fuels and wastes. Due to the fact that fluidized bed combustion technology offers a very high fuel flexibility and high combustion efficiency with low emissions it has become the dominating technology in co-combustion applications. This presentation will present Alhstrom`s experiences in co-combustion of biomasses in bubbling beds and Ahlstrom Pyroflow circulating fluidized beds based on about 200 operating references worldwide. CFB gasification will also be discussed 9 refs.

  9. Rotating Detonation Combustion: A Computational Study for Stationary Power Generation

    Science.gov (United States)

    Escobar, Sergio

    The increased availability of gaseous fossil fuels in The US has led to the substantial growth of stationary Gas Turbine (GT) usage for electrical power generation. In fact, from 2013 to 2104, out of the 11 Tera Watts-hour per day produced from fossil fuels, approximately 27% was generated through the combustion of natural gas in stationary GT. The thermodynamic efficiency for simple-cycle GT has increased from 20% to 40% during the last six decades, mainly due to research and development in the fields of combustion science, material science and machine design. However, additional improvements have become more costly and more difficult to obtain as technology is further refined. An alternative to improve GT thermal efficiency is the implementation of a combustion regime leading to pressure-gain; rather than pressure loss across the combustor. One concept being considered for such purpose is Rotating Detonation Combustion (RDC). RDC refers to a combustion regime in which a detonation wave propagates continuously in the azimuthal direction of a cylindrical annular chamber. In RDC, the fuel and oxidizer, injected from separated streams, are mixed near the injection plane and are then consumed by the detonation front traveling inside the annular gap of the combustion chamber. The detonation products then expand in the azimuthal and axial direction away from the detonation front and exit through the combustion chamber outlet. In the present study Computational Fluid Dynamics (CFD) is used to predict the performance of Rotating Detonation Combustion (RDC) at operating conditions relevant to GT applications. As part of this study, a modeling strategy for RDC simulations was developed. The validation of the model was performed using benchmark cases with different levels of complexity. First, 2D simulations of non-reactive shock tube and detonation tubes were performed. The numerical predictions that were obtained using different modeling parameters were compared with

  10. Time since discharge of 9mm cartridges by headspace analysis, part 1: Comprehensive optimisation and validation of a headspace sorptive extraction (HSSE) method.

    Science.gov (United States)

    Gallidabino, M; Romolo, F S; Weyermann, C

    2017-03-01

    Estimating the time since discharge of spent cartridges can be a valuable tool in the forensic investigation of firearm-related crimes. To reach this aim, it was previously proposed that the decrease of volatile organic compounds released during discharge is monitored over time using non-destructive headspace extraction techniques. While promising results were obtained for large-calibre cartridges (e.g., shotgun shells), handgun calibres yielded unsatisfying results. In addition to the natural complexity of the specimen itself, these can also be attributed to some selective choices in the methods development. Thus, the present series of paper aimed to more systematically evaluate the potential of headspace analysis to estimate the time since discharge of cartridges through the use of more comprehensive analytical and interpretative techniques. Specifically, in this first part, a method based on headspace sorptive extraction (HSSE) was comprehensively optimised and validated, as the latter recently proved to be a more efficient alternative than previous approaches. For this purpose, 29 volatile organic compounds were preliminary selected on the basis of previous works. A multivariate statistical approach based on design of experiments (DOE) was used to optimise variables potentially involved in interaction effects. Introduction of deuterated analogues in sampling vials was also investigated as strategy to account for analytical variations. Analysis was carried out by selected ion mode, gas chromatography coupled to mass spectrometry (GC-MS). Results showed good chromatographic resolution as well as detection limits and peak area repeatability. Application to 9mm spent cartridges confirmed that the use of co-extracted internal standards allowed for improved reproducibility of the measured signals. The validated method will be applied in the second part of this work to estimate the time since discharge of 9mm spent cartridges using multivariate models.

  11. Thermal behaviour and kinetics of coal/biomass blends during co-combustion.

    Science.gov (United States)

    Gil, M V; Casal, D; Pevida, C; Pis, J J; Rubiera, F

    2010-07-01

    The thermal characteristics and kinetics of coal, biomass (pine sawdust) and their blends were evaluated under combustion conditions using a non-isothermal thermogravimetric method (TGA). Biomass was blended with coal in the range of 5-80 wt.% to evaluate their co-combustion behaviour. No significant interactions were detected between the coal and biomass, since no deviations from their expected behaviour were observed in these experiments. Biomass combustion takes place in two steps: between 200 and 360 degrees C the volatiles are released and burned, and at 360-490 degrees C char combustion takes place. In contrast, coal is characterized by only one combustion stage at 315-615 degrees C. The coal/biomass blends presented three combustion steps, corresponding to the sum of the biomass and coal individual stages. Several solid-state mechanisms were tested by the Coats-Redfern method in order to find out the mechanisms responsible for the oxidation of the samples. The kinetic parameters were determined assuming single separate reactions for each stage of thermal conversion. The combustion process of coal consists of one reaction, whereas, in the case of the biomass and coal/biomass blends, this process consists of two or three independent reactions, respectively. The results showed that the chemical first order reaction is the most effective mechanism for the first step of biomass oxidation and for coal combustion. However, diffusion mechanisms were found to be responsible for the second step of biomass combustion.

  12. Effects of inlet distortion on gas turbine combustion chamber exit temperature profiles

    Science.gov (United States)

    Maqsood, Omar Shahzada

    Damage to a nozzle guide vane or blade, caused by non-uniform temperature distributions at the combustion chamber exit, is deleterious to turbine performance and can lead to expensive and time consuming overhaul and repair. A test rig was designed and constructed for the Allison 250-C20B combustion chamber to investigate the effects of inlet air distortion on the combustion chamber's exit temperature fields. The rig made use of the engine's diffuser tubes, combustion case, combustion liner, and first stage nozzle guide vane shield. Rig operating conditions simulated engine cruise conditions, matching the quasi-non-dimensional Mach number, equivalence ratio and Sauter mean diameter. The combustion chamber was tested with an even distribution of inlet air and a 4% difference in airflow at either side. An even distribution of inlet air to the combustion chamber did not create a uniform temperature profile and varying the inlet distribution of air exacerbated the profile's non-uniformity. The design of the combustion liner promoted the formation of an oval-shaped toroidal vortex inside the chamber, creating localized hot and cool sections separated by 90° that appeared in the exhaust. Uneven inlet air distributions skewed the oval vortex, increasing the temperature of the hot section nearest the side with the most mass flow rate and decreasing the temperature of the hot section on the opposite side. Keywords: Allison 250, Combustion, Dual-Entry, Exit Temperature Profile, Gas Turbine, Pattern Factor, Reverse Flow.

  13. Twenty-second symposium (international) on combustion

    Energy Technology Data Exchange (ETDEWEB)

    1989-01-01

    The following research areas were discussed at the symposium: coal combustion: carbon burnout, pyrolysis, furnaces, laboratory-scale combustion, and fluidized bed combustion; combustion-generated particulates: soot inception, growth, and soot formation in diffusion flames; engine combustion; turbulent combustion: flames in vortices, fractals and cellular automations, nonpremixed flames, premixed flames, premixed flame structure, and lifted flames; reaction kinetics: hydrocarbon oxidation, free radical chemistry, unsaturated species, aromatics, and nitrogen compounds/pollutant formation; combustion generated NO/sub x/ and SO/sub x/; fires: flame spread, radiation, characterization, and unsteady flames; Laminar flames: structure, opposed-flow combustion, shape, propagation/extinction, and inhibition, oscillations, microgravity; ignition; detonations; dusts; propellants; diagnostics; combustion of drops, sprays, and dispersions, and slurries. Individual projects are processed separately for the data bases. (CBS)

  14. Combustion iron distribution and deposition

    Science.gov (United States)

    Luo, Chao; Mahowald, N.; Bond, T.; Chuang, P. Y.; Artaxo, P.; Siefert, R.; Chen, Y.; Schauer, J.

    2008-03-01

    Iron is hypothesized to be an important micronutrient for ocean biota, thus modulating carbon dioxide uptake by the ocean biological pump. Studies have assumed that atmospheric deposition of iron to the open ocean is predominantly from mineral aerosols. For the first time we model the source, transport, and deposition of iron from combustion sources. Iron is produced in small quantities during fossil fuel burning, incinerator use, and biomass burning. The sources of combustion iron are concentrated in the industrialized regions and biomass burning regions, largely in the tropics. Model results suggest that combustion iron can represent up to 50% of the total iron deposited, but over open ocean regions it is usually less than 5% of the total iron, with the highest values (ocean biogeochemistry the bioavailability of the iron is important, and this is often estimated by the fraction which is soluble (Fe(II)). Previous studies have argued that atmospheric processing of the relatively insoluble Fe(III) occurs to make it more soluble (Fe(II)). Modeled estimates of soluble iron amounts based solely on atmospheric processing as simulated here cannot match the variability in daily averaged in situ concentration measurements in Korea, which is located close to both combustion and dust sources. The best match to the observations is that there are substantial direct emissions of soluble iron from combustion processes. If we assume observed soluble Fe/black carbon ratios in Korea are representative of the whole globe, we obtain the result that deposition of soluble iron from combustion contributes 20-100% of the soluble iron deposition over many ocean regions. This implies that more work should be done refining the emissions and deposition of combustion sources of soluble iron globally.

  15. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    The Combustion Byproducts Recycling Consortium (CBRC) program was developed as a focused program to remove and/or minimize the barriers for effective management of over 123 million tons of coal combustion byproducts (CCBs) annually generated in the USA. At the time of launching the CBRC in 1998, about 25% of CCBs were beneficially utilized while the remaining was disposed in on-site or off-site landfills. During the ten (10) year tenure of CBRC (1998-2008), after a critical review, 52 projects were funded nationwide. By region, the East, Midwest, and West had 21, 18, and 13 projects funded, respectively. Almost all projects were cooperative projects involving industry, government, and academia. The CBRC projects, to a large extent, successfully addressed the problems of large-scale utilization of CCBs. A few projects, such as the two Eastern Region projects that addressed the use of fly ash in foundry applications, might be thought of as a somewhat smaller application in comparison to construction and agricultural uses, but as a novel niche use, they set the stage to draw interest that fly ash substitution for Portland cement might not attract. With consideration of the large increase in flue gas desulfurization (FGD) gypsum in response to EPA regulations, agricultural uses of FGD gypsum hold promise for large-scale uses of a product currently directed to the (currently stagnant) home construction market. Outstanding achievements of the program are: (1) The CBRC successfully enhanced professional expertise in the area of CCBs throughout the nation. The enhanced capacity continues to provide technology and information transfer expertise to industry and regulatory agencies. (2) Several technologies were developed that can be used immediately. These include: (a) Use of CCBs for road base and sub-base applications; (b) full-depth, in situ stabilization of gravel roads or highway/pavement construction recycled materials; and (c) fired bricks containing up to 30%-40% F

  16. Ammonium Perchlorate and Ammonium Perchlorate- Hydroxyl Terminated Polybutadiene Simulated Combustion

    Directory of Open Access Journals (Sweden)

    Rene Francisco Boschi Gonçalves

    2012-03-01

    Full Text Available The combustion simulation of ammonium perchlorate was carried out with the software Chemkin, in two steps: the burning behavior of pure ammonium perchlorate and the one of formulated ammonium perchlorate with hydroxyl terminated polybutadiene binder. In both cases, the room pressure varied in order to verify its influence in the system. The burning environment conditions were diverse. During the combustion process, the data obtained from the kinetic chemistry simulation software were compiled. The flame structure can be described by the molar fraction of the burning products and the temperature evolution from the surface of the material.

  17. Subgrid Combustion Modeling for the Next Generation National Combustion Code

    Science.gov (United States)

    Menon, Suresh; Sankaran, Vaidyanathan; Stone, Christopher

    2003-01-01

    In the first year of this research, a subgrid turbulent mixing and combustion methodology developed earlier at Georgia Tech has been provided to researchers at NASA/GRC for incorporation into the next generation National Combustion Code (called NCCLES hereafter). A key feature of this approach is that scalar mixing and combustion processes are simulated within the LES grid using a stochastic 1D model. The subgrid simulation approach recovers locally molecular diffusion and reaction kinetics exactly without requiring closure and thus, provides an attractive feature to simulate complex, highly turbulent reacting flows of interest. Data acquisition algorithms and statistical analysis strategies and routines to analyze NCCLES results have also been provided to NASA/GRC. The overall goal of this research is to systematically develop and implement LES capability into the current NCC. For this purpose, issues regarding initialization and running LES are also addressed in the collaborative effort. In parallel to this technology transfer effort (that is continuously on going), research has also been underway at Georgia Tech to enhance the LES capability to tackle more complex flows. In particular, subgrid scalar mixing and combustion method has been evaluated in three distinctly different flow field in order to demonstrate its generality: (a) Flame-Turbulence Interactions using premixed combustion, (b) Spatially evolving supersonic mixing layers, and (c) Temporal single and two-phase mixing layers. The configurations chosen are such that they can be implemented in NCCLES and used to evaluate the ability of the new code. Future development and validation will be in spray combustion in gas turbine engine and supersonic scalar mixing.

  18. Turbulent Combustion in SDF Explosions

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A L; Bell, J B; Beckner, V E

    2009-11-12

    A heterogeneous continuum model is proposed to describe the dispersion and combustion of an aluminum particle cloud in an explosion. It combines the gas-dynamic conservation laws for the gas phase with a continuum model for the dispersed phase, as formulated by Nigmatulin. Inter-phase mass, momentum and energy exchange are prescribed by phenomenological models. It incorporates a combustion model based on the mass conservation laws for fuel, air and products; source/sink terms are treated in the fast-chemistry limit appropriate for such gasdynamic fields, along with a model for mass transfer from the particle phase to the gas. The model takes into account both the afterburning of the detonation products of the C-4 booster with air, and the combustion of the Al particles with air. The model equations were integrated by high-order Godunov schemes for both the gas and particle phases. Numerical simulations of the explosion fields from 1.5-g Shock-Dispersed-Fuel (SDF) charge in a 6.6 liter calorimeter were used to validate the combustion model. Then the model was applied to 10-kg Al-SDF explosions in a an unconfined height-of-burst explosion. Computed pressure histories are compared with measured waveforms. Differences are caused by physical-chemical kinetic effects of particle combustion which induce ignition delays in the initial reactive blast wave and quenching of reactions at late times. Current simulations give initial insights into such modeling issues.

  19. Explosion limits for combustible gases

    Institute of Scientific and Technical Information of China (English)

    TONG Min-ming; WU Guo-qing; HAO Ji-fei; DAI Xin-lian

    2009-01-01

    Combustible gases in coal mines are composed of methane, hydrogen, some multi-carbon alkane gases and other gases. Based on a numerical calculation, the explosion limits of combustible gases were studied, showing that these limits are related to the concentrations of different components in the mixture. With an increase of C4H10 and C6H14, the Lower ExplosionLimit (LEL) and Upper Explosion-Limit (UEL) of a combustible gas mixture will decrease clearly. For every 0.1% increase in C4H10 and C6H14, the LEL decreases by about 0.19% and the UEL by about 0.3%. The results also prove that, by increasing the amount of H2, the UEL of a combustible gas mixture will increase considerably. If the level of H2 increases by 0.1%, the UEL will increase by about 0.3%. However, H2 has only a small effect on the LEL of the combustible gas mixture. Our study provides a theoretical foundation for judging the explosion risk of an explosive gas mixture in mines.

  20. Bifurcation behaviors of catalytic combustion in a micro-channel

    Institute of Scientific and Technical Information of China (English)

    Wen Zeng; Maozhao Xie; Hongan Maa; Wei Xua

    2008-01-01

    Bifurcation analysis of ignition and extinction of catalytic combustion in a short micro-channel is carried out with the laminar flow model incorporated as the flow model. The square of transverse Thiele modulus and the realdence time are used as bifurcation parameters. The influences of different parameters on ignition and extinction behavior are investigated. It is shown that all these parameters have great effects on the bifurcation behaviors of ignition and extinction in the short micro-channel. The effects of flow models on bifurcation behaviors of combustion are also analyzed. The results show that in comparison with the fiat velocity profile model, for the case of the laminar flow model, the temperatures of ignition and extinction of combustion ate higher and the unsteady multiple solution region is larger.

  1. 3rd International Workshop on Turbulent Spray Combustion

    CERN Document Server

    Gutheil, Eva

    2014-01-01

    This book reflects the results of the 2nd and 3rd International Workshops on Turbulent Spray Combustion. The focus is on progress in experiments and numerical simulations for two-phase flows, with emphasis on spray combustion. Knowledge of the dominant phenomena and their interactions allows development of predictive models and their use in combustor and gas turbine design. Experts and young researchers present the state-of-the-art results, report on the latest developments and exchange ideas in the areas of experiments, modelling and simulation of reactive multiphase flows. The first chapter reflects on flame structure, auto-ignition and atomization with reference to well-characterized burners, to be implemented by modellers with relative ease. The second chapter presents an overview of first simulation results on target test cases, developed at the occasion of the 1st International Workshop on Turbulent Spray Combustion. In the third chapter, evaporation rate modelling aspects are covered, while the fourth ...

  2. Combustion performance evaluation of air staging of palm oil blends.

    Science.gov (United States)

    Mohd Jaafar, Mohammad Nazri; Eldrainy, Yehia A; Mat Ali, Muhammad Faiser; Wan Omar, W Z; Mohd Hizam, Mohd Faizi Arif

    2012-02-21

    The problems of global warming and the unstable price of petroleum oils have led to a race to develop environmentally friendly biofuels, such as palm oil or ethanol derived from corn and sugar cane. Biofuels are a potential replacement for fossil fuel, since they are renewable and environmentally friendly. This paper evaluates the combustion performance and emission characteristics of Refined, Bleached, and Deodorized Palm Oil (RBDPO)/diesel blends B5, B10, B15, B20, and B25 by volume, using an industrial oil burner with and without secondary air. Wall temperature profiles along the combustion chamber axis were measured using a series of thermocouples fitted axially on the combustion chamber wall, and emissions released were measured using a gas analyzer. The results show that RBDPO blend B25 produced the maximum emission reduction of 56.9% of CO, 74.7% of NOx, 68.5% of SO(2), and 77.5% of UHC compared to petroleum diesel, while air staging (secondary air) in most cases reduces the emissions further. However, increasing concentrations of RBDPO in the blends also reduced the energy released from the combustion. The maximum wall temperature reduction was 62.7% for B25 at the exit of the combustion chamber.

  3. Investigation of smoldering combustion propagation of dried peat

    Science.gov (United States)

    Palamba, Pither; Ramadhan, M. L.; Imran, F. A.; Kosasih, E. A.; Nugroho, Y. S.

    2017-03-01

    Smoldering is a form of combustion characterised by flameless burning of porous materials. Smoldering combustion of porous and organic soil such as peat, is considered as a major contributor to haze problem during wildland fires in Sumatra and Kalimantan, Indonesia. With almost half of tropical peatland worldwide, and vast area that resulted in its rich agricultural diversity, Indonesia possessed many variants of peat throughout the region. Thus, further highlighting the importance of characterizing the thermal properties of different varieties of peats for further analysis. An experimental test method was built to analyse the differences of varying peats from different parts of Indonesia, regarding its smoldering combustion propagation. In this case, peat from Papua and South Sumatera were analysed. A cylindrical wire meshed container of 190 cm3 in volume, was filled with dried peat. The temperature data and mass loss during the smoldering combustion was gathered using thermocouples and a DAQ system. After the experimental apparatus was set, a smoldering combustion of the dried peats was initiated at the top of the container using an electric heater. The results of the experiment showed a smoldering temperature of about 600°C and with a smoldering propagation rate of about 4.50 to 4.75 cm/h for both peat samples.

  4. New Combustion Regimes and Kinetic Studies of Plasma Assisted Combustion

    Science.gov (United States)

    2012-11-01

    Tasks 8 and 9: Kinetic model validation) Today’s Presentation 2. Multispecies diagnostics in a flow reactor with Mid-IR and molecular beam mass...S-Curve Competition between low T RO2 kinetics high T chain branching reactions 0.00 0.02 0.04 0.06 0.08 0.10 0.12 1x10 5 2x10 5 3x10 5 4x10...in Plasma assisted combustion • LTC in turbulent combustion at engine time scales 0-D modeling of DME /O2/He (0.03/0.1/0.896) ignition, P = 72

  5. A comprehensive fractal char combustion model☆

    Institute of Scientific and Technical Information of China (English)

    Yuting Liu; Rong He

    2016-01-01

    The char combustion mechanisms were analyzed and a comprehensive fractal char combustion model was developed to give a better understanding and better predictions of the char combustion characteristics. Most of the complex factors affecting the char combustion were included, such as the coupling effects between the pore diffusion and the chemical reactions, the evolution of the char pore structures and the variation of the apparent reaction order during combustion, the CO/CO2 ratio in the combustion products and the correction for oxy-char combustion. Eleven different chars were then combusted in two drop tube furnaces with the conversions of the partly burned char samples measured by thermogravimetric analysis. The combustion processes of these chars were simulated with the predicted char conversions matching very well with the measured data which shows that this char combustion model has good accuracy. The apparent reaction order of the char combustion decreases, stabilizes and then increases during the combustion process. The combustion rates in the oxy-mode are general y slower than in the air-mode and the effect of the char-CO2 gasification reac-tion becomes obvious only when the temperature is relatively high and the O2 concentration is relatively low.

  6. Novel Active Combustion Control Valve

    Science.gov (United States)

    Caspermeyer, Matt

    2014-01-01

    This project presents an innovative solution for active combustion control. Relative to the state of the art, this concept provides frequency modulation (greater than 1,000 Hz) in combination with high-amplitude modulation (in excess of 30 percent flow) and can be adapted to a large range of fuel injector sizes. Existing valves often have low flow modulation strength. To achieve higher flow modulation requires excessively large valves or too much electrical power to be practical. This active combustion control valve (ACCV) has high-frequency and -amplitude modulation, consumes low electrical power, is closely coupled with the fuel injector for modulation strength, and is practical in size and weight. By mitigating combustion instabilities at higher frequencies than have been previously achieved (approximately 1,000 Hz), this new technology enables gas turbines to run at operating points that produce lower emissions and higher performance.

  7. Randomized Comparison of Two Vaginal Self-Sampling Methods for Human Papillomavirus Detection: Dry Swab versus FTA Cartridge.

    Directory of Open Access Journals (Sweden)

    Rosa Catarino

    Full Text Available Human papillomavirus (HPV self-sampling (self-HPV is valuable in cervical cancer screening. HPV testing is usually performed on physician-collected cervical smears stored in liquid-based medium. Dry filters and swabs are an alternative. We evaluated the adequacy of self-HPV using two dry storage and transport devices, the FTA cartridge and swab.A total of 130 women performed two consecutive self-HPV samples. Randomization determined which of the two tests was performed first: self-HPV using dry swabs (s-DRY or vaginal specimen collection using a cytobrush applied to an FTA cartridge (s-FTA. After self-HPV, a physician collected a cervical sample using liquid-based medium (Dr-WET. HPV types were identified by real-time PCR. Agreement between collection methods was measured using the kappa statistic.HPV prevalence for high-risk types was 62.3% (95%CI: 53.7-70.2 detected by s-DRY, 56.2% (95%CI: 47.6-64.4 by Dr-WET, and 54.6% (95%CI: 46.1-62.9 by s-FTA. There was overall agreement of 70.8% between s-FTA and s-DRY samples (kappa = 0.34, and of 82.3% between self-HPV and Dr-WET samples (kappa = 0.56. Detection sensitivities for low-grade squamous intraepithelial lesion or worse (LSIL+ were: 64.0% (95%CI: 44.5-79.8 for s-FTA, 84.6% (95%CI: 66.5-93.9 for s-DRY, and 76.9% (95%CI: 58.0-89.0 for Dr-WET. The preferred self-collection method among patients was s-DRY (40.8% vs. 15.4%. Regarding costs, FTA card was five times more expensive than the swab (~5 US dollars (USD/per card vs. ~1 USD/per swab.Self-HPV using dry swabs is sensitive for detecting LSIL+ and less expensive than s-FTA.International Standard Randomized Controlled Trial Number (ISRCTN: 43310942.

  8. Combustion synthesis method and products

    Science.gov (United States)

    Holt, J.B.; Kelly, M.

    1993-03-30

    Disclosed is a method of producing dense refractory products, comprising: (a) obtaining a quantity of exoergic material in powder form capable of sustaining a combustion synthesis reaction; (b) removing absorbed water vapor therefrom; (c) cold-pressing said material into a formed body; (d) plasma spraying said formed body with a molten exoergic material to form a coat thereon; and (e) igniting said exoergic coated formed body under an inert gas atmosphere and pressure to produce self-sustained combustion synthesis. Also disclosed are products produced by the method.

  9. Chemical kinetics and combustion modeling

    Energy Technology Data Exchange (ETDEWEB)

    Miller, J.A. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to gain qualitative insight into how pollutants are formed in combustion systems and to develop quantitative mathematical models to predict their formation rates. The approach is an integrated one, combining low-pressure flame experiments, chemical kinetics modeling, theory, and kinetics experiments to gain as clear a picture as possible of the process in question. These efforts are focused on problems involved with the nitrogen chemistry of combustion systems and on the formation of soot and PAH in flames.

  10. Fundamentals of premixed turbulent combustion

    CERN Document Server

    Lipatnikov, Andrei

    2012-01-01

    Lean burning of premixed gases is considered to be a promising combustion technology for future clean and highly efficient gas turbine engines. This book highlights the phenomenology of premixed turbulent flames. The text provides experimental data on the general appearance of premixed turbulent flames, physical mechanisms that could affect flame behavior, and physical and numerical models aimed at predicting the key features of premixed turbulent combustion. The author aims to provide a simple introduction to the field for advanced graduate and postgraduate students. Topics covered include La

  11. Autodesk Combustion 4 fundamentals courseware

    CERN Document Server

    Autodesk,

    2005-01-01

    Whether this is your first experience with Combustion software or you're upgrading to take advantage of the many new features and tools, this guide will serve as your ultimate resource to this all-in-one professional compositing application. Much more than a point-and-click manual, this guide explains the principles behind the software, serving as an overview of the package and associated techniques. Written by certified Autodesk training specialists for motion graphic designers, animators, and visual effects artists, Combustion 4 Fundamentals Courseware provides expert advice for all skill le

  12. Spray combustion of biomass-based renewable diesel fuel using multiple injection strategy in a constant volume combustion chamber

    KAUST Repository

    Jing, Wei

    2016-05-26

    Effect of a two-injection strategy associated with a pilot injection on the spray combustion process was investigated under conventional diesel combustion conditions (1000 K and 21% O2 concentration) for a biomass-based renewable diesel fuel, i.e., biomass to liquid (BTL), and a regular No. 2 diesel in a constant volume combustion chamber using multiband flame measurement and two-color pyrometry. The spray combustion flame structure was visualized by using multiband flame measurement to show features of soot formation, high temperature and low temperature reactions, which can be characterized by the narrow-band emissions of radicals or intermediate species such as OH, HCHO, and CH. The objective of this study was to identify the details of multiple injection combustion, including a pilot and a main injection, and to provide further insights on how the two injections interact. For comparison, three injection strategies were considered for both fuels including a two-injection strategy (Case TI), single injection strategy A (Case SA), and single injection strategy B (Case SB). Multiband flame results show a strong interaction, indicated by OH emissions between the pilot injection and the main injection for Case TI while very weak connection is found for the narrow-band emissions acquired through filters with centerlines of 430 nm and 470 nm. A faster flame development is found for the main injection of Case TI compared to Cases SA and SB, which could be due to the high temperature environment and large air entrainment from the pilot injection. A lower soot level is observed for the BTL flame compared to the diesel flame for all three injection types. Case TI has a lower soot level compared to Cases SA and SB for the BTL fuel, while the diesel fuel maintains a similar soot level among all three injection strategies. Soot temperature of Case TI is lower for both fuels, especially for diesel. Based on these results, it is expected that the two-injection strategy could be

  13. A portable lab-on-a-chip instrument based on MCE with dual top-bottom capacitive coupled contactless conductivity detector in replaceable cell cartridge.

    Science.gov (United States)

    Ansari, Kambiz; Ying, Jasmine Yuen Shu; Hauser, Peter C; de Rooij, Nico F; Rodriguez, Isabel

    2013-05-01

    A new design for a compact portable lab-on-a-chip instrument based on MCE and dual capacitively coupled contactless conductivity detection (dC(4) D) is described. The instrument is battery powered with total dimension of 14 × 25 × 8 cm(3) (w × l × h), and weighs 1.2 kg. The device consists of a front electrophoresis compartment which has the chip holder and the chip, the associated high-voltage electrodes for electrophoresis injection and separation and the detector. The detection cell is integrated into the device housing with an exchangeable plug-and-play cartridge format. The design of the dC(4) D cell has been optimized for maximum performance. The cartridge includes the top-bottom excitation and pick up electrodes incorporated into the cell and connected to push-pull self-latching pins that are insulated with plastic. The metal frame of the cartridge is grounded completely to eliminate electronic interferences. The cartridge is designed to clamp a thin fluidic chip at the detection point. The cartridges are replaceable whereby different cartridges have different detection electrode configurations to employ according to the sensitivity or resolution needed in the specific analytical application. The second compartment consists of all the electronics, data acquisition card, high-voltage modules of up to ±5 kV both polarity, and batteries for 10 h of operation. The improved detector performance is illustrated by the electrophoresis analysis of six cations (NH4 (+) , K(+) , Ca(2+) , Na(+) , Mg(2+) , Li(+) ) with a detection limit of approximately 5 μM and the analysis of the anions (Br(-) , Cl(-) , NO2 (-) , NO3 (-) , SO4 (2-) , F(-) ) with a detection limit of about 3 μM. Analytical capabilities of the instrument for food and medical applications were evaluated by simultaneous detection of organic and inorganic acids in fruit juice and inorganic cations and anions in rabbit blood samples and human urine samples are also demonstrated.

  14. Free Energy and Internal Combustion Engine Cycles

    CERN Document Server

    Harris, William D

    2012-01-01

    The performance of one type (Carnot) of Internal Combustion Engine (ICE) cycle is analyzed within the framework of thermodynamic free energies. ICE performance is different from that of an External Combustion Engine (ECE) which is dictated by Carnot's rule.

  15. Scramjet Combustion Stability Behavior Modeling Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the means to accurately predict the combustion stability of a scramjet. This capability is very...

  16. Scramjet Combustion Stability Behavior Modeling Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A recent breakthrough in combustion stability analysis (UCDS) offers the potential to predict the combustion stability of a scramjet. This capability is very...

  17. Optimization of Post Combustion in Steelmaking (TRP 9925)

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Richard J. Fruehan; Dr. R. J. Matway

    2004-03-31

    In the electric arc furnace (EAF), and the basic oxygen furnace (BOF) for producing steel, the major off gas is carbon monoxide (CO). If the CO can be combusted to CO{sub 2}, and the energy transferred to the metal, this reaction will reduce the energy consumed in the EAF and allow for more scrap melting in the BOF which would significantly lower the energy required to produce steel. This reaction is referred to as post combustion. In order to optimize the post combustion process, computational fluid dynamic models (CFD) of the two steelmaking processes were developed. Before the models could be fully developed information on reactions affecting post combustion had to be obtained. The role of the reaction of CO{sub 2} with scrap (iron) was measured at the temperatures relevant to post combustion in laboratory experiments. The experiments were done to separate the effects of gas phase mass transfer, chemical kinetics, and solid state mass transfer through the iron oxide formed by the reaction. The first CFD model was for the EAF using the FIDAP-CFD{trademark} code. Whereas this model gave some useful results it was incomplete due to problems with the FIDAP program. In the second EAF model, the CFX{trademark} code was used and was much more successful. The full 3-D model included all forms of heat transfer and the back reactions of CO{sub 2} with the metal and scrap. The model for the EAF was a full 3-D model and consisted of a primary oxygen lance with side wall injectors for post combustion. The model could predict the degree of post combustion and heat transfer. The BOF model was a slice of the BOF for which there was symmetry. The model could predict post combustion, heat transfer, temperature profiles and the effect of operating variables such as oxygen flow rates and distribution. The present research developed several new models such as limited combustion and depostcombustion. These were all documented by MSA Pass as a sub-contract. Instruction manuals were

  18. Development of a Premixed Combustion Capability for Scramjet Combustion Experiments

    Science.gov (United States)

    Rockwell, Robert D.; Goyne, Christopher P.; Rice, Brian E.; Chelliah, Harsha; McDaniel, James C.; Edwards, Jack R.; Cantu, Luca M. L.; Gallo, Emanuela C. A.; Cutler, Andrew D.; Danehy, Paul M.

    2015-01-01

    Hypersonic air-breathing engines rely on scramjet combustion processes, which involve high speed, compressible, and highly turbulent flows. The combustion environment and the turbulent flames at the heart of these engines are difficult to simulate and study in the laboratory under well controlled conditions. Typically, wind-tunnel testing is performed that more closely approximates engine testing rather than a careful investigation of the underlying physics that drives the combustion process. The experiments described in this paper, along with companion data sets being developed separately, aim to isolate the chemical kinetic effects from the fuel-air mixing process in a dual-mode scramjet combustion environment. A unique fuel injection approach is taken that produces a nearly uniform fuel-air mixture at the entrance to the combustor. This approach relies on the precombustion shock train upstream of the dual-mode scramjet combustor. A stable ethylene flame anchored on a cavity flameholder with a uniformly mixed combustor inflow has been achieved in these experiments allowing numerous companion studies involving coherent anti-Stokes Raman scattering (CARS), particle image velocimetry (PIV), and planar laser induced fluorescence (PLIF) to be performed.

  19. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    NARCIS (Netherlands)

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion c

  20. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    NARCIS (Netherlands)

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion c

  1. Combustion Chemistry Diagnostics for Cleaner Processes.

    Science.gov (United States)

    Kohse-Höinghaus, Katharina

    2016-09-12

    Climate change, environmental problems, urban pollution, and the dependence on fossil fuels demand cleaner, renewable energy strategies. However, they also ask for urgent advances in combustion science to reduce emissions. For alternative fuels and new combustion regimes, crucial information about the chemical reactions from fuel to exhaust remains lacking. Understanding such relations between combustion process, fuel, and emissions needs reliable experimental data from a wide range of conditions to provide a firm basis for predictive modeling of practical combustion processes.

  2. Simulation study on combustion of biomass

    Science.gov (United States)

    Zhao, M. L.; Liu, X.; Cheng, J. W.; Liu, Y.; Jin, Y. A.

    2017-01-01

    Biomass combustion is the most common energy conversion technology, offering the advantages of low cost, low risk and high efficiency. In this paper, the transformation and transfer of biomass in the process of combustion are discussed in detail. The process of furnace combustion and gas phase formation was analyzed by numerical simulation. The experimental results not only help to optimize boiler operation and realize the efficient combustion of biomass, but also provide theoretical basis for the improvement of burner technology.

  3. Method and device for diagnosing and controlling combustion instabilities in internal combustion engines operating in or transitioning to homogeneous charge combustion ignition mode

    Science.gov (United States)

    Wagner, Robert M [Knoxville, TN; Daw, Charles S [Knoxville, TN; Green, Johney B [Knoxville, TN; Edwards, Kevin D [Knoxville, TN

    2008-10-07

    This invention is a method of achieving stable, optimal mixtures of HCCI and SI in practical gasoline internal combustion engines comprising the steps of: characterizing the combustion process based on combustion process measurements, determining the ratio of conventional and HCCI combustion, determining the trajectory (sequence) of states for consecutive combustion processes, and determining subsequent combustion process modifications using said information to steer the engine combustion toward desired behavior.

  4. Combustor nozzle for a fuel-flexible combustion system

    Science.gov (United States)

    Haynes, Joel Meier [Niskayuna, NY; Mosbacher, David Matthew [Cohoes, NY; Janssen, Jonathan Sebastian [Troy, NY; Iyer, Venkatraman Ananthakrishnan [Mason, OH

    2011-03-22

    A combustor nozzle is provided. The combustor nozzle includes a first fuel system configured to introduce a syngas fuel into a combustion chamber to enable lean premixed combustion within the combustion chamber and a second fuel system configured to introduce the syngas fuel, or a hydrocarbon fuel, or diluents, or combinations thereof into the combustion chamber to enable diffusion combustion within the combustion chamber.

  5. 30 CFR 56.4104 - Combustible waste.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Combustible waste. 56.4104 Section 56.4104... Control Prohibitions/precautions/housekeeping § 56.4104 Combustible waste. (a) Waste materials, including... properly, waste or rags containing flammable or combustible liquids that could create a fire hazard shall...

  6. Straw combustion on slow-moving grates

    DEFF Research Database (Denmark)

    Kær, Søren Knudsen

    2005-01-01

    Combustion of straw in grate-based boilers is often associated with high emission levels and relatively poor fuel burnout. A numerical grate combustion model was developed to assist in improving the combustion performance of these boilers. The model is based on a one-dimensional ‘‘walking...

  7. Preparation of amino-modified active carbon cartridges and their use in the extraction of quercetin from Oldenlandia diffusa.

    Science.gov (United States)

    Zhu, Tao; Row, Kyung Ho

    2011-12-05

    Polyethyleneimine (PEI) and ethylenediamine (EDA) as modifiers were bonded on active carbon (AC) surface for specific selective extraction of quercetin from Oldenlandia diffusa. The characteristics of the modified AC materials that were obtained were investigated by field emission-scanning electron microscopy (FE-SEM) and Fourier transform infrared spectrometer (FT-IR). The interactions between quercetin and the AC materials were investigated by fitting the static adsorption data to four linear and nonlinear adsorption isotherm models. Of these four models, the Langmuir-Freundlich adsorption isotherm was proved the best for investigating quercetin on AC materials. Scatchard analysis was used to evaluate the binding properties of the AC materials for quercetin. Solvent extraction and solid-phase extraction (SPE) were optimized, and the effect of the mobile phase pH was investigated to improve the performance for the separation of quercetin on high performance liquid chromatography (HPLC). The results from the validation of the proposed analytical method demonstrated that the EDA-modified AC was the most suitable SPE cartridge for the purification of quercetin from O. diffusa. Copyright © 2011 Elsevier B.V. All rights reserved.

  8. Coal combustion products: trash or treasure?

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, T.

    2006-07-15

    Coal combustion by-products can be a valuable resource to various industries. The American Coal Ash Association (ACAA) collects data on production and uses of coal combustion products (CCPs). 122.5 million tons of CCPs were produced in 2004. The article discusses the results of the ACCA's 2004 survey. Fly ash is predominantly used as a substitute for Portland cement; bottom ash for structural fill, embankments and paved road cases. Synthetic gypsum from the FGD process is commonly used in wallboard. Plant owners are only likely to have a buyer for a portion of their CCPs. Although sale of hot water (from Antelope Valley Station) from condensers for use in a fish farm to raise tilapia proved unviable, the Great Plains Synfuels Plant which manufactures natural gas from lignite produces a wide range of products including anhydrous ammonia, phenol, krypton, carbon dioxide (for enhanced oil recovery), tar oils and liquid nitrogen. ACCA's goal is to educate people about CCPs and how to make them into useful products, and market them, in order to reduce waste disposal and enhance revenue. The article lists members of the ACCA. 2 photos., 1 tab.

  9. Catalytic reduction of emissions from small scale wood combustion. State of the art

    Energy Technology Data Exchange (ETDEWEB)

    Hargitai, T.; Silversand, F.A. [Katator AB, Lund (Sweden)

    1998-12-31

    Small-scale combustion of big-fuel often results in excessive emissions of volatile organic compounds (VOC), polyaromatic compounds (PAM) and carbon monoxide (CO). These compounds have a negative impact on human health and urban air quality. The predominant volatile organic compounds present in flue gases from big-fuel combustion are propylene, ethylene, butadiene, methanol, ethanol, methane, phenol and benzene. The poor combustion performance of some wood stoves has in certain cases led to legislation against small-scale combustion of big-fuel in urban areas. Catalytic cleaning is one very efficient way of decreasing the environmental impacts of big-fuel combustion. Several studies concerning catalytic purification of flue gases from big-fuel combustion have been presented over the years. Several problems must be addressed when designing a catalyst for this application: Clogging problems from deposition of ashes and particulates in the catalyst; Catalyst poisoning by sulphur, phosphorus, alkali metals etc.; Catalyst fouling due to deposition of ashes and particulates; Catalyst overheating at high flue-gas temperatures and Poor catalyst performance during start-up Most studies have been focused on monolith-type catalysts and- the conversion of CO, VOC and PAH typically is above 80 %. The observed problems are associated with increased pressure drop due to catalyst clogging and decreased catalyst performance due to fouling and poisoning. In most cases precious metals, preferably Pt. have been used as active combustion catalyst. Precious metals have a high activity for the combustion of CO and hydrocarbons and a fair stability against poisoning with compounds present in flue gases from big-fuel, e.g. sulphur and alkali metals. The majority of the studies on precious metals have been focused on Pt. Rh and Pd, which are especially active in catalytic combustion. Some metal oxides are used in catalytic combustion, especially at low temperatures (e.g. in VOC abatement

  10. Liquid rocket combustion instability analysis by CFD methods

    Science.gov (United States)

    Grenda, J. M.; Venkateswaran, S.; Merkle, C. L.

    1991-01-01

    Combustion instability in liquid rocket engines is simulated computationally by using a simple two-parameter model for the combustion response function. The objectives of the study are to assess the capabilities of CFD algorithms for instability studies and to investigate the response to parametric effects such as bombs and distributed combustion. Results indicate that numerical solutions of high accuracy can be obtained if a sufficient number of grid points are used per wavelength of the disturbance. The short-term response to bombs or pulses triggers a large number of modes in the combustor whose faithful resolution requires highly dense grids, although there is evidence that correct long-term solutions can be obtained even if all the short-term frequencies are not resolved. Long-term responses to pulses are shown to decay to the most unstable mode in small amplitude cases, and to exhibit limit cycles in large amplitude cases. Comparison of distributed with concentrated heat release indicates the former is more stable for given values of the combustion response parameters, and that the distributed heat release gives rise to higher frequency disturbances. Wave steepening is observed in the solutions, but its effect is less pronounced in multidimensional waves than in one-dimensional waves.

  11. The Combination of Internal-Combustion Engine and Gas Turbine

    Science.gov (United States)

    Zinner, K.

    1947-01-01

    While the gas turbine by itself has been applied in particular cases for power generation and is in a state of promising development in this field, it has already met with considerable success in two cases when used as an exhaust turbine in connection with a centrifugal compressor, namely, in the supercharging of combustion engines and in the Velox process, which is of particular application for furnaces. In the present paper the most important possibilities of combining a combustion engine with a gas turbine are considered. These "combination engines " are compared with the simple gas turbine on whose state of development a brief review will first be given. The critical evaluation of the possibilities of development and fields of application of the various combustion engine systems, wherever it is not clearly expressed in the publications referred to, represents the opinion of the author. The state of development of the internal-combustion engine is in its main features generally known. It is used predominantly at the present time for the propulsion of aircraft and road vehicles and, except for certain restrictions due to war conditions, has been used to an increasing extent in ships and rail cars and in some fields applied as stationary power generators. In the Diesel engine a most economical heat engine with a useful efficiency of about 40 percent exists and in the Otto aircraft engine a heat engine of greatest power per unit weight of about 0.5 kilogram per horsepower.

  12. Sulfur Chemistry in Combustion II

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Kiil, Søren

    2000-01-01

    Several options are available to control the emission of SO2 from combustion processes. One possibility is to use a cleaner technology, i.e. fuel switching from oil and coal to natural gas or biomass, or to desulphurize coal and oil. Another possibility is to change to a different technology for ...

  13. Leaching from biomass combustion ash

    DEFF Research Database (Denmark)

    Maresca, Alberto; Astrup, Thomas Fruergaard

    2014-01-01

    The use of biomass combustion ashes for fertilizing and liming purposes has been widely addressed in scientific literature. Nevertheless, the content of potentially toxic compounds raises concerns for a possible contamination of the soil. During this study five ash samples generated at four...

  14. A case of suicide using a home-modified gun.

    Science.gov (United States)

    Di Nunno, Nunzio; Viola, Luigi; Colucci, Monica; Di Nunno, Cosimo; Costantinides, Fulvio

    2009-03-01

    The problem of the possibility of modifying blank cartridge dummy firearms to make them fire a real bullet has long been known, but the phenomenon has been constantly on the increase in the recent years. In Italy, there are no restrictions on the purchase of an inoffensive weapon. However, few modifications are frequently enough to transform the inoffensive weapon into a harmful one: a procedure is often undertaken to avoid the mandatory control and registration of firearms. We describe a case of suicide of a man in Trieste, Italy, in 2002, with a blank cartridge dummy pistol that had been modified to fire homemade bullets.

  15. A Reduced Order Model for the Design of Oxy-Coal Combustion Systems

    Directory of Open Access Journals (Sweden)

    Steven L. Rowan

    2015-01-01

    Full Text Available Oxy-coal combustion is one of the more promising technologies currently under development for addressing the issues associated with greenhouse gas emissions from coal-fired power plants. Oxy-coal combustion involves combusting the coal fuel in mixtures of pure oxygen and recycled flue gas (RFG consisting of mainly carbon dioxide (CO2. As a consequence, many researchers and power plant designers have turned to CFD simulations for the study and design of new oxy-coal combustion power plants, as well as refitting existing air-coal combustion facilities to oxy-coal combustion operations. While CFD is a powerful tool that can provide a vast amount of information, the simulations themselves can be quite expensive in terms of computational resources and time investment. As a remedy, a reduced order model (ROM for oxy-coal combustion has been developed to supplement the CFD simulations. With this model, it is possible to quickly estimate the average outlet temperature of combustion flue gases given a known set of mass flow rates of fuel and oxidant entering the power plant boiler as well as determine the required reactor inlet mass flow rates for a desired outlet temperature. Several cases have been examined with this model. The results compare quite favorably to full CFD simulation results.

  16. Simultaneous measurement of droplet size and velocity field by an interferometric imaging technique in spray combustion

    Energy Technology Data Exchange (ETDEWEB)

    Fujisawa, N.; Hosokawa, A.; Tomimatsu, S. [Niigata Univ. (Japan). Dept. of Mechanical and Production Engineering

    2003-08-01

    The present paper describes an experimental technique of droplet sizing and velocity measurement for application to a luminous flame in spray combustion. The size measurement of unburnt fuel droplets in combustion is carried out by using an interferometric imaging method, while the corresponding velocity field is measured by particle tracking velocimetry (PTV) in combination with the rotary shutter to avoid the high intensity noise of the luminous flame in spray combustion. The measurements are successfully applied to the spray flow from a gun-type burner with and without combustion. The experimental results in spray combustion indicate that the smaller size of fuel droplets are almost burnt in the centre of the flame and the unburnt droplets of larger size remain in the outer region of the burner flow. It was found that the mean droplet velocity measured by the present PTV technique in combustion is almost independent of the droplet size and agrees closely with the gas velocity. However, the velocity magnitude with combustion is increased in comparison with the case without combustion, which suggests the influence of gas expansion at high temperatures. (author)

  17. Environmental optimisation of waste combustion

    Energy Technology Data Exchange (ETDEWEB)

    Schuster, Robert [AaF Energikonsult, Stockholm (Sweden); Berge, Niclas; Stroemberg, Birgitta [TPS Termiska Processer AB, Nykoeping (Sweden)

    2000-12-01

    The regulations concerning waste combustion evolve through R and D and a strive to get better and common regulations for the European countries. This study discusses if these rules of today concerning oxygen concentration, minimum temperature and residence time in the furnace and the use of stand-by burners are needed, are possible to monitor, are the optimum from an environmental point of view or could be improved. No evidence from well controlled laboratory experiments validate that 850 deg C in 6 % oxygen content in general is the best lower limit. A lower excess air level increase the temperature, which has a significant effect on the destruction of hydrocarbons, favourably increases the residence time, increases the thermal efficiency and the efficiency of the precipitators. Low oxygen content is also necessary to achieve low NO{sub x}-emissions. The conclusion is that the demands on the accuracy of the measurement devices and methods are too high, if they are to be used inside the furnace to control the combustion process. The big problem is however to find representative locations to measure temperature, oxygen content and residence time in the furnace. Another major problem is that the monitoring of the operation conditions today do not secure a good combustion. It can lead to a false security. The reason is that it is very hard to find boilers without stratifications. These stratifications (stream lines) has each a different history of residence time, mixing time, oxygen and combustible gas levels and temperature, when they reach the convection area. The combustion result is the sum of all these different histories. The hydrocarbons emission is in general not produced at a steady level. Small clouds of unburnt hydrocarbons travels along the stream lines showing up as peaks on a THC measurement device. High amplitude peaks has a tendency to contain higher ratio of heavy hydrocarbons than lower peaks. The good correlation between some easily detected

  18. Industrial chemistry. Tome 3, combustion and explosion of gaseous mixtures. Course and solved exercises; Chimie industrielle. Tome 3, combustions et explosions des melanges gazeux. Cours et problemes resolus

    Energy Technology Data Exchange (ETDEWEB)

    Lefrancois, B. [Conservatoire National des Arts et Metiers (CNAM), 75 - Paris (France)

    1999-07-01

    This book comprises a course about the combustion and explosion of gaseous mixtures, followed by 12 exercises of application with their solution. The seven chapters of the course deal successively with: 1 - general considerations about combustions and explosions: definitions, chemical equations of combustion, standard combustion and decomposition enthalpies, internal combustion energy, oxygen statement, forecasting of the explosive property, risk assessment; 2 - flame temperatures: adiabatic flame temperatures and complete reactions, adiabatic combustion pressure at constant volume, adiabatic flame temperatures and equilibrium reactions, examples of calculations; 3 - ignition temperatures: measurement (pyrometry), mechanism, delay, variations of ignition temperature, ignition of a gas mixture by adiabatic compression, ignition of a gas mixture by contact with a very hot solid, ignition temperatures and safety; 4 - flammability limits of gaseous mixtures: pure materials in air, flammable gas mixtures, safety; 5 - deflagration in gaseous phase: phenomenon, mechanism, variations of propagation velocities, jamming diameter and distance, deflagration initiated inside a tube with one end closed, deflagration inside a closed cell; 6 - detonation in gaseous phase: phenomenon, general characteristics and mechanism, variations of detonation propagation velocities, limits of detonability, priming of detonations, shock waves and combustion, deflagration primed detonation and pressures profile, comparison between the two types of heterogenous explosions (deflagration and detonation in gases); 7 - atmospheric dispersion: general aspects, Gaussian models, particular cases. (J.S.)

  19. Numerical simulation and modeling of combustion in scramjets

    Science.gov (United States)

    Clark, Ryan James

    In the last fifteen years the development of a viable scramjet has quickly approached the following long term goals: responsive sub-orbital space access; long-range, prompt global strike; and high-speed transportation. Nonetheless, there are significant challenges that need to be resolved. These challenges include high skin friction drag and high heat transfer rates, inherent to vehicles in sustained, hypersonic flight. Another challenge is sustaining combustion. Numerical simulation and modeling was performed to provide insight into reducing skin friction drag and sustaining combustion. Numerical simulation was used to investigate boundary layer combustion, which has been shown to reduce skin friction drag. The objective of the numerical simulations was to quantify the effect of fuel injection parameters on boundary layer combustion and ultimately on the change in the skin friction coefficient and heat transfer rate. A qualitative analysis of the results suggest that the reduction in the skin friction coefficient depends on multiple parameters and potentially an interaction between parameters. Sustained combustion can be achieved through a stabilized detonation wave. Additionally, stabilizing a detonation wave will yield rapid combustion. This will allow for a shorter and lighter-weight engine system, resulting in less required combustor cooling. A stabilized detonation wave was numerically modeled for various inlet and geometric cases. The effect of fuel concentration, inlet Mach number, and geometric configuration on the stability of a detonation wave was quantified. Correlations were established between fuel concentration, inlet speed, geometric configuration and parameters characterizing the detonation wave. A linear relationship was quantified between the fuel concentration and the parameters characterizing the detonation wave.

  20. Fluidized-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Kudjoi, A.; Heinolainen, A.; Hippinen, I.; Lu, Y. [Helsinki University of Technology, Espoo (Finland). Lab. of Energy Economics and Power Plant Engineering

    1998-12-31

    Hybrid combined cycle processes have been presented as possibilities for power generation in the future. In the processes based on partial gasification of coal, the solid materials removed from a gasifier (i.e. fly ash and bed char) contain unburned fuel, which is burned either in an atmospheric or a pressurised fluidised-bed. Pressurised fluidised-bed (PFB) combustion of gasification residues were studied experimentally by Helsinki University of Technology. The gasification residues, i.e. cyclone fines and bed chars, came from pilot scale PFB gasification tests of bituminous coals. The combustion efficiency was high in cyclone fines combustion. The calcium sulphide oxidised effectively to calcium sulphate in the combustion of cyclone fines. In bed char combustion the residual sulphide contents in solids after combustion were still relatively high. In general, sulphur dioxide emissions in residue combustion were low. The recarbonation of calcium oxide was observed in bed char combustion. Fuel-N conversion to NO{sub x} during bed char combustion and in most of the test runs with cyclone fines was higher than in bituminous coal combustion. In bed char combustion the conversion was significantly higher than in cyclone fines combustion. NO{sub x} emissions increased with increasing excess air for both residues, as was expected. In bed char combustion the highest NO{sub x} emissions were measured at higher pressure. Calculated mass reactivity values of equal particle size of all bed chars studied had similar trends with burnout. The biggest particles had the lowest reactivity values throughout the combustion, while reactivity for finer particles was at considerably higher level and sharply increases with burnout. In the constant combustion conditions used in the tests, no significant differences were observed in rate-controlling mechanisms for bed char fractions studied. 25 refs., 13 figs., 15 tab.

  1. Combustive management of oil spills

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    Extensive experiments with in situ incineration were performed on a desert site at the University of Arizona with very striking results. The largest incinerator, 6 feet in diameter with a 30 foot chimney, developed combustion temperatures of 3000, F, and attendant soot production approximately 1000 times less than that produced by conventional in situ burning. This soot production, in fact, is approximately 30 times less than current allowable EPA standards for incinerators and internal combustion engines. Furthermore, as a consequence of the high temperature combustion, the bum rate was established at a very high 3400 gallons per hour for this particular 6 foot diameter structure. The rudimentary design studies we have carried out relative to a seagoing 8 foot diameter incinerator have predicted that a continuous burn rate of 7000 gallons per hour is realistic. This structure was taken as a basis for operational design because it is compatible with C130 flyability, and will be inexpensive enough ($120,000 per copy) to be stored at those seaside depots throughout the US coast line in which the requisite ancillary equipments (booms, service tugs, etc.) are already deployed. The LOX experiments verified our expectations with respect to combustion of debris and various highly weathered or emulsified oils. We have concluded, however, that the use of liquid oxygen in actual beach clean up is not promising because the very high temperatures associated with this combustion are almost certain to produce environmentally deleterious effects on the beach surface and its immediately sublying structures. However, the use of liquid oxygen augmentation for shore based and flyable incinerators may still play an important role in handing the problem of accumulated debris.

  2. Transport Properties for Combustion Modeling

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J.; Bastein, L.; Price, P.N.

    2010-02-19

    This review examines current approximations and approaches that underlie the evaluation of transport properties for combustion modeling applications. Discussed in the review are: the intermolecular potential and its descriptive molecular parameters; various approaches to evaluating collision integrals; supporting data required for the evaluation of transport properties; commonly used computer programs for predicting transport properties; the quality of experimental measurements and their importance for validating or rejecting approximations to property estimation; the interpretation of corresponding states; combination rules that yield pair molecular potential parameters for unlike species from like species parameters; and mixture approximations. The insensitivity of transport properties to intermolecular forces is noted, especially the non-uniqueness of the supporting potential parameters. Viscosity experiments of pure substances and binary mixtures measured post 1970 are used to evaluate a number of approximations; the intermediate temperature range 1 < T* < 10, where T* is kT/{var_epsilon}, is emphasized since this is where rich data sets are available. When suitable potential parameters are used, errors in transport property predictions for pure substances and binary mixtures are less than 5 %, when they are calculated using the approaches of Kee et al.; Mason, Kestin, and Uribe; Paul and Warnatz; or Ern and Giovangigli. Recommendations stemming from the review include (1) revisiting the supporting data required by the various computational approaches, and updating the data sets with accurate potential parameters, dipole moments, and polarizabilities; (2) characterizing the range of parameter space over which the fit to experimental data is good, rather than the current practice of reporting only the parameter set that best fits the data; (3) looking for improved combining rules, since existing rules were found to under-predict the viscosity in most cases; (4

  3. Side-by-side comparison of disposable microchips with commercial capillary cartridges for application in capillary isoelectric focusing with whole column imaging detection.

    Science.gov (United States)

    Liu, Zhen; Ou, Junjie; Samy, Razim; Glawdel, Tomasz; Huang, Tiemin; Ren, Carolyn L; Pawliszyn, Janusz

    2008-10-01

    Simple-structured, well-functioned disposable poly(dimethylsiloxane) (PDMS) microchips were developed for capillary isoelectric focusing with whole column imaging detection (CIEF-WCID). Side-by-side comparison of the developed microchips with well-established commercial capillary cartridges demonstrated that the disposable microchips have comparable performance as well as advantages such as absence of lens effect and possibility of high-aspect-ratio accompanied with a dramatic reduction in cost.

  4. Efficiency of Polyphenol Extraction from Artificial Honey Using C18 Cartridges and Amberlite® XAD-2 Resin: A Comparative Study

    OpenAIRE

    Chua Yung An; Md. Murad Hossain; Fahmida Alam; Md. Asiful Islam; Md. Ibrahim Khalil; Nadia Alam; Siew Hua Gan,

    2016-01-01

    A comparative study of the extraction efficiency of nine known polyphenols [phenolic acids (benzoic acid, dihydroxybenzoic acid, gallic acid, trans-cinnamic acid, and vanillic acid) and flavonoids (naringenin, naringin, quercetin, and rutin)] was conducted by deliberately adding the polyphenols to an artificial honey solution and performing solid phase extraction (SPE). Two SPE methods were compared: one using Amberlite XAD-2 resin and another one using a C18 cartridge. A gradient high perfor...

  5. Emission characteristics and combustion instabilities in an oxy-fuel swirl-stabilized combustor

    Institute of Scientific and Technical Information of China (English)

    Guo-neng LI; Hao ZHOU; Ke-fa CEN

    2008-01-01

    This paper presents an experimental study on the emission characteristics and combustion instabilities of oxy-fuel combustions in a swirl-stabilized combustor.Different oxygen concentrations(Xoxy=25%-45%,where Xoxy is oxygen concentra-tion by volume),equivalence ratios(=0.75~1.15)and combustion powers(CP=1.08~2.02kW)were investigated in the oxy-fuel (CH4/CO2/O2)combustions,and reference cases(Xoxy=25%~35%,Cha/N2/O2 flames)were covered.The results show that the oxygen concentration in the oxidant stream significantly affects the combustion delay in the oxy-fuel flames,and the equivalence ratio has a slight effect,whereas the combustion power shows no impact.The temperature levels of the oxy-fuel flames inside the combustion chamber are much higher(up to 38.7%)than those of the reference cases.Carbon monoxide was vastly producedwhen Xoxy>35% or >0.95 in the oxy-fuel flames,while no nitric oxide was found in the exhaust gases because no N2 participates in the combustion process.The combustion instability of the oxy-fuel combustion is very different from those of the reference cases with similar oxygen content.Oxy-fuel combustions excite strong oscillations in all cases studied Xoxy=25%~45%.However,no pressure fluctuations were detected in the reference cases when Xoxy>28.6% accomplished by heavily sooting flames which were not found in the oxy-fuel combustions.Spectrum analysis shows that the frequency of dynamic pressure oscillations exhibits randomness in the range of 50~250 Hz,therefore resulting in a very small resultant amplitude.Temporal oscillations are very strong with amplitudes larger than 200 Pa,even short time fast Fourier transform(FFT)analysis(0.08 s)shows that the pressure amplitude can be larger than 40 Pa.

  6. Research into Radar Multi-station Joint Movement Against Chaff Cartridge Jamming%雷达多站联动抗箔条弹干扰研究

    Institute of Scientific and Technical Information of China (English)

    曹志宏; 张新星; 刁华伟

    2012-01-01

    Though analyzing the jamming area of single chaff cartridge,this paper educes that the is definite blind zone when aircrafts launch chaff cartridges backwards,analyzes the feasibility th deploying the fire control radar in the blind zone to raise the anti-chaff cartridge jamming capabili re at ty of radar,demonstrates the rationality of using multi-station joint movement to confront the chaff catridge jamming,which has much help for advancing the combat efficiency of fire control radars.%通过对单枚箔条弹的干扰区进行分析,得出飞机后向发射箔条弹时存在一定的盲区,分析了在此盲区中部署火控雷达对提高雷达的反箔条弹干扰能力的可行性,验证了在此种情况下依靠多站联动抗箔条弹干扰的合理性,对提高火控雷达的作战效能有很大的帮助。

  7. Extension of the ReaxFF Combustion Force Field toward Syngas Combustion and Initial Oxidation Kinetics.

    Science.gov (United States)

    Ashraf, Chowdhury; van Duin, Adri C T

    2017-02-09

    A detailed insight of key reactive events related to oxidation and pyrolysis of hydrocarbon fuels further enhances our understanding of combustion chemistry. Though comprehensive kinetic models are available for smaller hydrocarbons (typically C3 or lower), developing and validating reaction mechanisms for larger hydrocarbons is a daunting task, due to the complexity of their reaction networks. The ReaxFF method provides an attractive computational method to obtain reaction kinetics for complex fuel and fuel mixtures, providing an accuracy approaching ab-initio-based methods but with a significantly lower computational expense. The development of the first ReaxFF combustion force field by Chenoweth et al. (CHO-2008 parameter set) in 2008 has opened new avenues for researchers to investigate combustion chemistry from the atomistic level. In this article, we seek to address two issues with the CHO-2008 ReaxFF description. While the CHO-2008 description has achieved significant popularity for studying large hydrocarbon combustion, it fails to accurately describe the chemistry of small hydrocarbon oxidation, especially conversion of CO2 from CO, which is highly relevant to syngas combustion. Additionally, the CHO-2008 description was obtained faster than expected H abstraction by O2 from hydrocarbons, thus underestimating the oxidation initiation temperature. In this study, we seek to systemically improve the CHO-2008 description and validate it for these cases. Additionally, our aim was to retain the accuracy of the 2008 description for larger hydrocarbons and provide similar quality results. Thus, we expanded the ReaxFF CHO-2008 DFT-based training set by including reactions and transition state structures relevant to the syngas and oxidation initiation pathways and retrained the parameters. To validate the quality of our force field, we performed high-temperature NVT-MD simulations to study oxidation and pyrolysis of four different hydrocarbon fuels, namely, syngas

  8. Secondary combustion device for woodburning stove

    Energy Technology Data Exchange (ETDEWEB)

    Craver, R.D.

    1989-08-08

    This patent describes in a wood burning stove including an exhaust flue opening, a combustion chamber for primary combustion having an access door, a support for wood to be burned and a primary air inlet means for supplying air to support primary combustion of the wood to produce flue gases containing combustible particulate material, plenum means for directing the flue gases in a direction from the combustion chamber to the flue opening in a preselected path, and secondary combustion means for burning the particulate material in the flue gases before flue gases through the exhaust flue opening. The improvement comprising: the combustion chamber having a flue gas exit opening extending laterally across the top of the combustion chamber and communicating the combustion chamber with the plenum means, an elongated manifold extending laterally across and above the combustion chamber substantially coextensively with the flue gas exit opening, a number of air opening spaced longitudinally along the manifold and facing opposite the direction of the flue gases closely adjacent the flue gas exit opening, and an air inlet means for supplying ambient, secondary combustion air to the manifold for counterflow thereof from the openings into the path of the flue gases in a plurality of distinct jets.

  9. Measurement and simulation of swirling coal combustion

    Institute of Scientific and Technical Information of China (English)

    Liyuan Hu; Lixing Zhou; Yonghao Luo; Caisong Xu

    2013-01-01

    Particle image velocimetry (PIV),thermocouples and flue gas analyzer are used to study swirling coal combustion and NO formation under different secondary-air ratios.Eulerian-Lagrangian large-eddy simulation (LES) using the Smagorinsky-Lilly sub-grid scale stress model,presumed-PDF fast chemistry and eddy-break-up (EBU) gas combustion models,particle devolatilization and particle combustion models,are simultaneously used to simulate swirling coal combustion.Statistical LES results are validated by measurement results.Instantaneous LES results show that the coherent structures for swirling coal combustion are stronger than those for swirling gas combustion.Particles are shown to concentrate along the periphery of the coherent structures.Combustion flame is located in the high vorticity and high particle concentration zones.Measurement shows that secondary-air ratios have little effect on final NO formation at the exit of the combustor.

  10. Combustion diagnostic for active engine feedback control

    Science.gov (United States)

    Green, Jr., Johney Boyd; Daw, Charles Stuart; Wagner, Robert Milton

    2007-10-02

    This invention detects the crank angle location where combustion switches from premixed to diffusion, referred to as the transition index, and uses that location to define integration limits that measure the portions of heat released during the combustion process that occur during the premixed and diffusion phases. Those integrated premixed and diffusion values are used to develop a metric referred to as the combustion index. The combustion index is defined as the integrated diffusion contribution divided by the integrated premixed contribution. As the EGR rate is increased enough to enter the low temperature combustion regime, PM emissions decrease because more of the combustion process is occurring over the premixed portion of the heat release rate profile and the diffusion portion has been significantly reduced. This information is used to detect when the engine is or is not operating in a low temperature combustion mode and provides that feedback to an engine control algorithm.

  11. Evaluation and optimisation of phenomenological multi-step soot model for spray combustion under diesel engine-like operating conditions

    DEFF Research Database (Denmark)

    Pang, Kar Mun; Jangi, Mehdi; Bai, Xue-Song

    2015-01-01

    with the spray combustion solver. Prior to the soot modelling, combustion simulations are carried out. Numerical results show that the ignition delay times and lift-off lengths exhibit good agreement with the experimental measurements across a wide range of operating conditions, apart from those in the cases...

  12. Distributed Low Temperature Combustion: Fundamental Understanding of Combustion Regime Transitions

    Science.gov (United States)

    2016-09-07

    Excellent optical access for laser- based diagnostic measurements ; (ii) Accurate experimental control of boundary conditions; (iii) Aerodynamic flame...potential to extend methods based on bimodal approximations, such as the BML [21] framework , by permitting inter- mediate fluid states, which is of...identify the impact of the major chemical pathways on combustion mode transitions. The conceptual multifluid approach of Spalding can be used to avoid

  13. 77 FR 37361 - National Emission Standards for Hazardous Air Pollutants for Reciprocating Internal Combustion...

    Science.gov (United States)

    2012-06-21

    ... Reciprocating Internal Combustion Engines; New Source Performance Standards for Stationary Internal Combustion... Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines.'' The EPA... Internal Combustion Engines; New Source Performance Standards for Stationary Internal Combustion Engines...

  14. Flamelet Regime Diagram for Turbulent Combustion Simulations

    Science.gov (United States)

    Chan, Wai Lee; Ihme, Matthias; Kolla, Hemanth; Chen, Jacqueline

    2016-11-01

    The flamelet model has been widely used in numerical combustion investigations, particularly for the closure of large-eddy simulations (LES) of turbulent reacting flows. In most cases, the simulation results demonstrated good agreements with their experimental counterparts. However, a systematic analysis of the flamelet model's applicability, as well as its potential limitations, is seldom conducted, and the model performance is usually based only on a-posteriori comparisons. The objective of this work is to derive a metric that can formally quantify the suitability of the flamelet model in different flame configurations. For this purpose, a flamelet regime diagram has been developed and studied in the context of direct numerical simulations (DNS) of a turbulent lifted jet flame. The implementation of the regime diagram in LES has been investigated through explicit filtering of the DNS results.

  15. Combustion and economics of coal slurry fuels: a look at coal-fuel oil slurries

    Energy Technology Data Exchange (ETDEWEB)

    Murayama, T.; Matsuoka, H.

    1984-01-01

    With the aim of reducing dependence on petroleum, research has been going ahead into the development of various alternative fuels. Of these, coal slurry fuels are regarded as being first in line for commercialization. The authors discuss the combustion of coal-oil fuels. The combustion of fuel oil, pulverized coal and coal-water slurry is also examined. In each case, combustion properties and associated problems are discussed. Finally, the economics of these fuels are examined and trends in research and development surveyed. 23 references.

  16. Numerical Simulation of NOx Formation in Coal Combustion with Inlet Natural Gas Burning

    Institute of Scientific and Technical Information of China (English)

    张宇; 周力行; 魏小林; 盛宏至

    2005-01-01

    A full two-fluid model of reacting gas-particle flows and coal combustion is used to simulate coal combustion with and without inlet natural gas added in the inlet. The simulation results for the case without natural gas burning is in fair agreement with the experimental results reported in references. The simulation results of different natural gas adding positions indicate that the natural gas burning can form lean oxygen combustion enviroment at the combustor inlet region and the NOx concentration is reduced. The same result can be obtained from chemical equilibrium analysis.

  17. Ash and heavy metals in fluidized-bed combustion of wood wastes; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

    Energy Technology Data Exchange (ETDEWEB)

    Kaessi, T.; Aittoniemi, P. [IVO Power Engineering, Vantaa (Finland); Kauppinen, E.; Latva-Somppi, J.; Kurkela, J. [VTT Chemical Technology, Espoo (Finland); Partanen, J. [IVO Technology Centre, Vantaa (Finland)

    1997-10-01

    Ash formation and deposition mechanisms during co-combustion of pulp mill sludge and bark in industrial bubbling fluidized bed (BFB) combustor have been studied. Similar fuels were used in a bench-scale BFB for co-combustion of sludge and bark pellets and comparative studies with separate combustion of these fuels. Results indicated that in industrial scale unit significant fraction of ash had vaporization. About 14 mass-% of the total fly ash was found in the particle size below 0.2 {mu}m. The vaporized species consisted of potassium (K), sulfur (S), chlorine (Cl) and also of minor quantities of sodium (Na). In the benchscale similar vaporization fractions during co-combustion were measured, about 11 mass-%. During the combustion of bark this ratio, about 20 mass-%, was higher than during sludge combustion. The vaporized ash fraction was in the case of dried sludge combustion about 7 mass-%, but with wet sludge the vaporization rate was remarkably lower, about 1-2 mass-%. An increase in the bed temperature increased also ash vaporization. Test run period without combustion at elevated temperatures produced very low quantities of vaporized ash. The vaporized species in bench-scale test during bark pellet combustion were K, S and Cl, for sludge combustion also Na was clearly detected. No condensation of the vaporized species in bed area or furnace walls was observed. Bed defluidization was studied in the bench-scale unit. During bark pellet combustion the bed-agglomeration proceeded via small ash particle, below 2 {mu}m, coating on sand particle surface and consequent bonding between the ash layers. In the case of sludge combustion the accumulation of large ash particles and sintering of these porous agglomerates was observed to cause bed coarsening and defluidization. (orig.)

  18. Monitoring of the radiocesium in river water in Fukushima using rapid and simultaneous monitoring of particulate and dissolved radiocesium in water with nonwoven fabric cartridge filters

    Energy Technology Data Exchange (ETDEWEB)

    Tsuji, H.; Yasutaka, T. [National Institute of Advanced Industrial Science and Technology (Japan); Kondo, Y. [Japan Vilene Company, Ltd (Japan); Suzuki, Y. [Fukushima Agricultural Technology Centre (Japan)

    2014-07-01

    The environmental monitoring of dissolved and particulate radiocesium in river became important after the accident of TEPCO Fukushima Daiichi Nuclear Power Plant. Traditional monitoring methods, such as evaporative concentration, require time for pre-processing because the concentration of dissolved radiocesium of river water in Fukushima prefecture is currently very low, averagely 0.001 - 0.1 Bq/L. Our research group has developed a monitoring method to investigate the radiocesium concentration in water by each existence form. Yasutaka et al. (2013) and Tsuji et al.(2013) developed a method for rapid and simultaneous monitoring of particulate and dissolved radiocesium in water with nonwoven fabric cartridge filters. This method uses pleated polypropylene nonwoven fabric filter with a pore size of 1-μm to collect particulate radiocesium, and nonwoven fabric impregnated with Prussian blue (PB) to absorb dissolved radiocesium. The fabric was placed into cylindrical plastic cartridges (SS-cartridge and PB-cartridge). This method could catch the 99% of the suspended solid (SS) and absorb 95% of dissolved radiocesium separately in 20 L water within 40 minutes. This device was applied to monitor the water in Abukuma River (January 2013) and upper area of Kuchibuto river (May 2013) at 12 locations, and the results were compared with those obtained by the filtrating and evaporative concentration method. The SS concentration and radioactivity of SS in the Abukuma river water, calculated by weight gain of the SS-cartridge and by sediment weight after filtration with a 0.45-μm membrane filter, agreed well without one location.The radioactivity of the dissolved {sup 137}Cs also agreed well between these two methods. In the Abukuma River, dissolved {sup 137}Cs was 0.006-0.025 Bq/L and particulate {sup 137}Cs was 0.008-0.070 Bq/L by the presented method in January 2013. In addition, the required time for pre-processing was reduced by more than 10 times that by filtrating and

  19. The new INNOVANCE® PFA P2Y cartridge is sensitive to the detection of the P2Y₁₂ receptor inhibition.

    Science.gov (United States)

    Koessler, Juergen; Kobsar, Anna L; Rajkovic, Mirjana S; Schafer, Andreas; Flierl, Ulrike; Pfoertsch, Stephanie; Bauersachs, Johann; Steigerwald, Udo; Rechner, Andreas R; Walter, Ulrich

    2011-01-01

    Insufficient response on antiplatelet medication has become an intensively discussed issue because of the risk factor of recurrent adverse cardiovascular events. However, the monitoring of antiplatelet therapy requires appropriate, robust and reliable test methods. For the measurement of thienopyridine effects, the manufacturer of the PFA-100® System provides the INNOVANCE® PFA P2Y * cartridge. We tested this cartridge for its capacity to detect the inhibition of the P2Y₁₂ receptor, which is the target for thienopyridine medication (e.g. clopidogrel). We compared the INNOVANCE® PFA P2Y * results with those obtained by the receptor specific flow cytometric vasodilator stimulated phosphoprotein (VASP) assay that expresses the status of the P2Y₁₂ receptor as "platelet reactivity index" (PRI). The in vitro addition of the P2Y₁₂ receptor antagonist cangrelor (AR-C69931MX) to citrated human whole blood resulted in a dose-dependent prolongation of closure times (CTs) of the INNOVANCE® PFA P2Y * cartridge correlating with decreased PRI levels. In volunteers, the intake of a 600 mg clopidogrel loading dose caused an increase of the CTs in all volunteers, although some of these volunteers were identified as "poor responders" by the VASP assay (no significant reduction of PRI levels). In 50 patients with stable coronary artery disease undergoing percutaneous coronary intervention (PCI) and under dual antiplatelet therapy, the new cartridge had a detection rate of 84% (CT 106 s as cut-off) for clopidogrel medication. After dividing the 50 patients into two groups according to their response to clopidogrel INNOVANCE® PFA P2Y * recognized all "responders" (defined by a PRI > 50%) using >106 s as cut-off but the specificity for a "good response" was only 42% because several "poor responders" (defined by a PRI > 50%) also showed CTs above the cut-off. The best correlation (substantial agreement) between the results of INNOVANCE® PFA P2Y * and of the VASP

  20. Low Temperature Combustion Demonstrator for High Efficiency Clean Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Ojeda, William de

    2010-07-31

    The project which extended from November 2005 to May of 2010 demonstrated the application of Low Temperature Combustion (LTC) with engine out NOx levels of 0.2 g/bhp-hr throughout the program target load of 12.6bar BMEP. The project showed that the range of loads could be extended to 16.5bar BMEP, therefore matching the reference lug line of the base 2007 MY Navistar 6.4L V8 engine. Results showed that the application of LTC provided a dramatic improvement over engine out emissions when compared to the base engine. Furthermore LTC improved thermal efficiency by over 5% from the base production engine when using the steady state 13 mode composite test as a benchmark. The key enablers included improvements in the air, fuel injection, and cooling systems made in Phases I and II. The outcome was the product of a careful integration of each component under an intelligent control system. The engine hardware provided the conditions to support LTC and the controller provided the necessary robustness for a stable combustion. Phase III provided a detailed account on the injection strategy used to meet the high load requirements. During this phase, the control strategy was implemented in a production automotive grade ECU to perform cycle-by-cycle combustion feedback on each of the engine cylinders. The control interacted on a cycle base with the injection system and with the Turbo-EGR systems according to their respective time constants. The result was a unique system that could, first, help optimize the combustion system and maintain high efficiency, and secondly, extend the steady state results to the transient mode of operation. The engine was upgraded in Phase IV with a Variable Valve Actuation system and a hybrid EGR loop. The impact of the more versatile EGR loop did not provide significant advantages, however the application of VVA proved to be an enabler to further extend the operation of LTC and gain considerable benefits in fuel economy and soot reduction. Finally

  1. Quantitative analysis of four protein biomarkers: An automated microfluidic cartridge-based method and its comparison to colorimetric ELISA.

    Science.gov (United States)

    Dysinger, Mark; Marusov, Greg; Fraser, Stephanie

    2017-09-13

    Biomarker quantitation with ligand binding assays has matured greatly in recent years. This maturation has been partly in response to demands for more data points from fewer samples or less available sample volume. Multiplexing offers opportunities to acquire data for multiple analytes from single sample assay iterations, but has its own unique challenges and limitations. ProteinSimple has developed Simple Plex™, an automated immunoassay platform consisting of microfluidic cartridge-based assays run on the Ella instrument. Ella subverts traditional multiplexing challenges by rapidly performing triplicate measurements of up to four different analytes simultaneously, each in their own respective assay vessels and all from a single sample. Here we describe a comparison of the Simple Plex platform versus colorimetric ELISA and their respective abilities to quantitate four common biomarkers (MCP-1/CCL2, VEGF-A, TNF-α, and IL-6) from twenty-eight healthy individual donor plasma samples. Each biomarker was tested on the two platforms on each of two days. Ella analysis required significantly reduced sample volume, manual steps, and total time. Overall, Ella was able to quantify results for all twenty-eight samples for each of the four biomarkers. In contrast, ELISA was able to measure quantifiable results within respective calibration curve ranges for MCP-1/CCL2 (96% of samples) and VEGFA (7% of samples). For TNF-α and IL-6, ELISA was not sensitive enough to quantify any samples in the assay ranges. This stark difference in quantitative results underscores Ella's ability to multiplex without compromising sensitivity, and has far reaching potential for biomarker panel measurement in support of diagnosis, prognosis, and monitoring of disease. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Determination of closantel residues in milk and animal tissues by HPLC with fluorescence detection and SPE with oasis MAX cartridges.

    Science.gov (United States)

    Sun, Han-Wen; Wang, Feng-Chi; Ai, Lian-Feng

    2008-04-01

    A liquid chromatographic method for the determination of closantel residues in milk and tissues is developed and validated. An acetonitrile-acetone solution (80:20, v/v) is used for the extraction of closantel residues from milk and animal tissues, and the extract is purified by solid-phase extraction with Oasis MAX cartridges and a mixture of formic acid-acetonitrile (5:95, v/v) as the elution solution. A C(18) bonded silica column is used for chromatographic separation. The mobile phase consists of acetonitrile-water (85:15, v/v) containing 0.05% triethylamine at pH 2.5, adjusted with phosphoric acid with the flow-rate set at 1.0 mL/min. Using the fluorescence emission of closantel at lambda(ex) = 335 nm and lambda(ex) = 510 nm, the calibration curve is linear, with a correlation coefficient of 0.9999 over the concentration range of 10-5000 microg/kg for the tissue sample and 10-5000 microg/L for the milk sample. The detection limit (s/n = 3) is 3 microg/kg for tissue sample and 3 microg/L for milk sample. The intra- and inter-day repeatabilities are between 3.35-7.66% and 4.04-8.67%, respectively. The proposed method enables the quantitative determination of closantel residues at levels as low as 10 microg/kg in animal tissue samples and 10 microg/L in milk samples.

  3. Proteoglycan from salmon nasal cartridge promotes in vitro wound healing of fibroblast monolayers via the CD44 receptor

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Gen; Kobayashi, Takeshi; Takeda, Yoshie [Department of Physiology, Nagoya University Graduate School of Medicine, Nagoya, Aichi 466-8550 (Japan); Sokabe, Masahiro, E-mail: msokabe@med.nagoya-u.ac.jp [Department of Physiology, Nagoya University Graduate School of Medicine, Nagoya, Aichi 466-8550 (Japan); Mechanobiology Laboratory, Nagoya University Graduate School of Medicine, Nagoya, Aichi 466-8550 (Japan); Mechanobiology Institute Singapore, National University of Singapore, Singapore 117411 (Singapore)

    2015-01-16

    Highlights: • Proteoglycan from salmon nasal cartridge (SNC-PG) promoted wound healing in fibroblast monolayers. • SNC-PG stimulated both cell proliferation and cell migration. • Interaction between chondroitin sulfate-units and CD44 is responsible for the effect. - Abstract: Proteoglycans (PGs) are involved in various cellular functions including cell growth, adhesion, and differentiation; however, their physiological roles are not fully understood. In this study, we examined the effect of PG purified from salmon nasal cartilage (SNC-PG) on wound closure using tissue-cultured cell monolayers, an in vitro wound-healing assay. The results indicated that SNC-PG significantly promoted wound closure in NIH/3T3 cell monolayers by stimulating both cell proliferation and cell migration. SNC-PG was effective in concentrations from 0.1 to 10 μg/ml, but showed much less effect at higher concentrations (100–1000 μg/ml). The effect of SNC-PG was abolished by chondroitinase ABC, indicating that chondroitin sulfates (CSs), a major component of glycosaminoglycans (GAGs) in SNC-PG, are crucial for the SNC-PG effect. Furthermore, chondroitin 6-sulfate (C-6-S), a major CS of SNC-PG GAGs, could partially reproduce the SNC-PG effect and partially inhibit the binding of SNC-PG to cells, suggesting that SNC-PG exerts its effect through an interaction between the GAGs in SNC-PG and the cell surface. Neutralization by anti-CD44 antibodies or CD44 knockdown abolished SNC-PG binding to the cells and the SNC-PG effect on wound closure. These results suggest that interactions between CS-rich GAG-chains of SNC-PG and CD44 on the cell surface are responsible for the SNC-PG effect on wound closure.

  4. Are adrenaline autoinjectors fit for purpose? A pilot study of the mechanical and injection performance characteristics of a cartridge- versus a syringe-based autoinjector

    Directory of Open Access Journals (Sweden)

    Andreas Schwirtz

    2010-11-01

    Full Text Available Andreas Schwirtz, Harald SeegerPharma Consult GmbH, Vienna, AustriaBackground: Adrenaline autoinjectors (AAIs are prescribed to facilitate the intramuscular administration of adrenaline in patients diagnosed with life-threatening anaphylaxis. This pilot study investigated the injection and functional properties of two AAIs (deploying different delivery systems under standard conditions, after dynamic and mechanical stresses, and in the presence of denim.Methods: The differences between a cartridge-based AAI (EpiPen® Junior and a syringe-based AAI (Anapen® Junior were assessed using three sets of tests. Test 1: under standard conditions, the injection depth and dose were measured in ballistic gelatine (a validated tissue simulant. Test 2: before the safety cap removal and activation forces were measured, AAIs were subjected to either of two preconditioning tests: 1 free-fall drop test; or 2 static load (ie, 400 N, equivalent to 40 kg weight test; or 3 no preconditioning. Test 3: under standard conditions, injection properties into ballistic gelatine in the presence and absence of denim were investigated. Statistical analyses were performed using the Student’s t-test or Welch’s test.Results: The maximum depth of delivery was significantly greater with cartridge AAI (n = 4, mean 21.09 ± 2.54 mm than with syringe AAI (n = 5; mean 11.64 ± 0.80 mm; P = 0.003. After 2.5 seconds, cartridge AAI (n = 4 discharged significantly more dose than syringe AAI (n = 3; 74.3% versus 25.7% of total dose; P = 0.001. Both cartridge and syringe AAI withstood the free-fall drop test, but almost all devices failed to activate following the static load test. Under standard conditions, significantly less force was required to remove the safety cap of cartridge AAI than syringe AAI (both n = 15; mean 9.56 ± 2.36 N versus 20.23 ± 6.61 N, respectively; P < 0.001, but a significantly greater activation force was required for cartridge AAI than syringe AAI (mean 23

  5. Oxy-coal Combustion Studies

    Energy Technology Data Exchange (ETDEWEB)

    Wendt, J. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Lighty, J. [Univ. of Utah, Salt Lake City, UT (United States); Ring, T. [Univ. of Utah, Salt Lake City, UT (United States); Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Thornock, J. [Univ. of Utah, Salt Lake City, UT (United States); Y Jia, W. Morris [Univ. of Utah, Salt Lake City, UT (United States); Pedel, J. [Univ. of Utah, Salt Lake City, UT (United States); Rezeai, D. [Univ. of Utah, Salt Lake City, UT (United States); Wang, L. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, J. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States)

    2012-01-06

    The objective of this project is to move toward the development of a predictive capability with quantified uncertainty bounds for pilot-scale, single-burner, oxy-coal operation. This validation research brings together multi-scale experimental measurements and computer simulations. The combination of simulation development and validation experiments is designed to lead to predictive tools for the performance of existing air fired pulverized coal boilers that have been retrofitted to various oxy-firing configurations. In addition, this report also describes novel research results related to oxy-combustion in circulating fluidized beds. For pulverized coal combustion configurations, particular attention is focused on the effect of oxy-firing on ignition and coal-flame stability, and on the subsequent partitioning mechanisms of the ash aerosol.

  6. Fundamental studies of spray combustion

    Energy Technology Data Exchange (ETDEWEB)

    Li, S.C.; Libby, P.A.; Williams, F.A. [Univ. of California, San Diego, CA (United States)

    1997-12-31

    Our research on spray combustion involves both experiment and theory and addresses the characteristics of individual droplets and of sprays in a variety of flows: laminar and turbulent, opposed and impinging. Currently our focus concerns water and fuel sprays in two stage laminar flames, i.e., flames arising, for example from a stream of fuel and oxidizer flowing opposite to an air stream carrying a water spray. Our interest in these flames is motivated by the goals of reducing pollutant emissions and extending the range of stable spray combustion. There remains considerable research to be carried out in order to achieve these goals. Thus far our research on the characteristics of sprays in turbulent flows has been limited to nonreacting jets impinging on a plate but this work will be extended to opposed flows with and without a flame. In the following we discuss details of these studies and our plans for future work.

  7. SPECIFIC EMISSIONS FROM BIOMASS COMBUSTION

    Directory of Open Access Journals (Sweden)

    Pavel Skopec

    2014-02-01

    Full Text Available This paper deals with determining the specific emissions from the combustion of two kinds of biomass fuels in a small-scale boiler. The tested fuels were pellets made of wood and pellets made of rape plant straw. In order to evaluate the specific emissions, several combustion experiments were carried out using a commercial 25 kW pellet-fired boiler. The specific emissions of CO, SO2 and NOx were evaluated in relation to a unit of burned fuel, a unit of calorific value and a unit of produced heat. The specific emissions were compared with some data acquired from the reference literature, with relatively different results. The differences depend mainly on the procedure used for determining the values, and references provide no information about this. Although some of our experimental results may fit with one of the reference sources, they do not fit with the other. The reliability of the references is therefore disputable.

  8. Fluidized bed coal combustion reactor

    Science.gov (United States)

    Moynihan, P. I.; Young, D. L. (Inventor)

    1981-01-01

    A fluidized bed coal reactor includes a combination nozzle-injector ash-removal unit formed by a grid of closely spaced open channels, each containing a worm screw conveyor, which function as continuous ash removal troughs. A pressurized air-coal mixture is introduced below the unit and is injected through the elongated nozzles formed by the spaces between the channels. The ash build-up in the troughs protects the worm screw conveyors as does the cooling action of the injected mixture. The ash layer and the pressure from the injectors support a fluidized flame combustion zone above the grid which heats water in boiler tubes disposed within and/or above the combustion zone and/or within the walls of the reactor.

  9. The FCF Combustion Integrated Rack: Microgravity Combustion Science Onboard the International Space Station

    Science.gov (United States)

    OMalley, Terence F.; Weiland, Karen J.

    2002-01-01

    The Combustion Integrated Rack (CIR) is one of three facility payload racks being developed for the International Space Station (ISS) Fluids and Combustion Facility (FCF). Most microgravity combustion experiments will be performed onboard the Space Station in the Combustion Integrated Rack. Experiment-specific equipment will be installed on orbit in the CIR to customize it to perform many different scientific experiments during the ten or more years that it will operate on orbit. This paper provides an overview of the CIR, including a description of its preliminary design and planned accommodations for microgravity combustion science experiments, and descriptions of the combustion science experiments currently planned for the CIR.

  10. High-Speed Visualisation of Combustion in Modern Gasoline Engines

    Science.gov (United States)

    Sauter, W.; Nauwerck, A.; Han, K.-M.; Pfeil, J.; Velji, A.; Spicher, U.

    2006-07-01

    Today research and development in the field of gasoline engines have to face a double challenge: on the one hand, fuel consumption has to be reduced, while on the other hand, ever more stringent emission standards have to be fulfilled. The development of engines with its complexity of in-cylinder processes requires modern development tools to exploit the full potential in order to reduce fuel consumption. Especially optical, non-intrusive measurement techniques will help to get a better understanding of the processes. With the presented high-speed visualisation system the electromagnetic radiation from combustion in the UV range is collected by an endoscope and transmitted to a visualisation system by 10, 000 optical fibres. The signal is projected to 1, 920 photomultipliers, which convert the optical into electric signals with a maximum temporal resolution of 200 kHz. This paper shows the systematic application of flame diagnostics in modern combustion systems. For this purpose, a single-cylinder SI engine has been modified for a spray guided combustion strategy as well as for HCCI. The characteristics of flame propagation in both combustion modes were recorded and correlated with thermodynamic analyses. In case of the spray guided GDI engine, high pressure fuel injection was applied and evaluated.

  11. CSIR helps prevent spontaneous combustion

    Energy Technology Data Exchange (ETDEWEB)

    Vuuren, M. van (CSIR Energy Technology (South Africa))

    1992-03-01

    Heaps of stockpiled coal could present a fire hazard due to the risk of spontaneous combustion. Regular monitoring of stockpiles and bunker testing of coals help to prevent stockpile fires. This brief article describes the recent upgrading of the CSIR's bunker test facility that enables coal producers, users and exporters to test their products under simulated conditions that duplicate the actual conditions under which coal is stored. 2 photos.

  12. Radiation/Catalytic Augmented Combustion.

    Science.gov (United States)

    1980-09-01

    NATIO& NAk H(fJI At tl TANUAHTOb 19 A ~omm.81-0287 LVL RADIATION/CATALYTIC AUGMENTED COMBUST ION MOSHE LAVID CORPORATE RESEARCH-TECHNOLOGY FEASIBILITY...refinements as necessary. i. Perform cannular combustor experiments to Investigate ignition and flame attachment in flowing, liquid -fuel, unpremixed...stabilizer, with a sintered metal disk on the downstream side through which hot gases or products of partial fuel oxidation can be passed. Experimental

  13. Laser Optics/Combustion Diagnostics.

    Science.gov (United States)

    1986-07-01

    been demonstrated. CARS measurements of axial and 0.12 radial temperature profiles in a highly sooting flame compared favorably with profiles...of Number-Density Equation ’Eckbreth. A.C. and Hatt. R.., "CARS Thermomrry in a The third-order susceptibility can be rewritten to show its Sooting ... Flame ." Combustion and Homie, Vol. 36. 1979, pp. 87-98. explcitdepndece ponthenumer ensty Roh. %W.B.. "Coherent Anti-Stokcs Raman Scattering ofexpici

  14. ABB Combustion Engineering nuclear technology

    Energy Technology Data Exchange (ETDEWEB)

    Matzie, R.A.

    1994-12-31

    The activities of ABB Combustion Engineering in the design and construction of nuclear systems and components are briefly reviewed. ABB Construction Engineering continues to improve the design and design process for nuclear generating stations. Potential improvements are evaluated to meet new requirements both of the public and the regulator, so that the designs meet the highest standards worldwide. Advancements necessary to meet market needs and to ensure the highest level of performance in the future will be made.

  15. Vortex Simulation of Turbulent Combustion

    Science.gov (United States)

    1992-11-19

    TURBULENT COMBUSTION (AFOSR Grant No. 89-0491) Principal Investigator: Ahmed F. Ghoniem Department of Mechanical Engineering Massachusetts Institute of...Heavy Industries, Nagoya, Japan.(talk and discussion). 17. 1990, Mazda Motor Co., Yokohama, Japan, (talk and discussion). 18. 1990, American Math Society...VORTICITY LAYERS UNDER NON-SYMMETRIC CONDITIONS Omar M. Kniot and Ahmed F. Ghoniem Department of Mechanical Engineering Massachusetts Institute of

  16. Nitrogen release during coal combustion

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, L.L.; Mitchell, R.E.; Fletcher, T.H.; Hurt, R.H.

    1995-02-01

    Experiments in entrained flow reactors at combustion temperatures are performed to resolve the rank dependence of nitrogen release on an elemental basis for a suite of 15 U.S. coals ranging from lignite to low-volatile bituminous. Data were obtained as a function of particle conversion, with overall mass loss up to 99% on a dry, ash-free basis. Nitrogen release rates are presented relative to both carbon loss and overall mass loss. During devolatilization, fractional nitrogen release from low-rank coals is much slower than fractional mass release and noticeably slower than fractional carbon release. As coal rank increases, fractional nitrogen release rate relative to that of carbon and mass increases, with fractional nitrogen release rates exceeding fractional mass and fractional carbon release rates during devolatilization for high-rank (low-volatile bituminous) coals. At the onset of combustion, nitrogen release rates increase significantly. For all coals investigated, cumulative fractional nitrogen loss rates relative to those of mass and carbon passes through a maximum during the earliest stages of oxidation. The mechanism for generating this maximum is postulated to involve nascent thermal rupture of nitrogen-containing compounds and possible preferential oxidation of nitrogen sites. During later stages of oxidation, the cumulative fractional loss of nitrogen approaches that of carbon for all coals. Changes in the relative release rates of nitrogen compared to those of both overall mass and carbon during all stages of combustion are attributed to a combination of the chemical structure of coals, temperature histories during combustion, and char chemistry.

  17. The effect of fuel pyrolysis on the coal particle combustion: An analytical investigation

    OpenAIRE

    Baghsheikhi Mostafa; Rahbari Alireza; Ashrafizadeh Seyed Mehdi; Bidabadi Mehdi

    2016-01-01

    The aim of this work is to analytically investigate the symmetrical combustion of an isolated coal particle with the fuel pyrolysis effect. The modelling concept of coal particles is similar to that of the liquid droplet combustion but in the case of coal devolatilization, the particles do not shrink like droplet does due to evaporation of liquid fuel. The rate of devolatilization of volatiles can be calculated using the equation that is similar to Arrheniu...

  18. Multidimensional Modeling of Fuel Composition Effects on Combustion and Cold-starting in Diesel Engines

    Science.gov (United States)

    1995-01-01

    equally important for both the gas and liquid phase. For the gas phase, a modified Redlich - Kwong equation of state is used (Prausnitz, [lo]). In the...residual fuel mass (case 9). Ignition started early but the combustion developed at a slower rate. Another application of an altered engine geometry...Power, Vol. 115, pp. 781-789,1993. 17. Kong, S.C., Han, Z., and Reitz, R.D., “The Development and Application of a Diesel Ignition and Combustion

  19. Combustion char characterisation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, P.; Ingermann Petersen, H.; Sund Soerensen, H.; Thomsen, E.; Guvad, C.

    1996-06-01

    The aim was to correlate reactivity measures of raw coals and the maceral concentrates of the coals obtained in a previous project with the morphology of the produced chars by using a wire grid devolatilization method. Work involved determination of morphology, macroporosity and a detailed study by Scanning Electron Microscopy (SEM). Systematic variations in the texture of chars produced in different temperature domains and heating rates were demonstrated by using incident light microscopy on polished blocks and by SEM studies directly on the surfaces of untreated particles. Results suggest that work in the field of char reactivity estimates and correlations between char morphology and coal petrography can be accomplished only on chars produced under heating rates and temperatures comparable to those for the intended use of coal. A general correlation between the coals` petrography and the the morphology of high temperature chars was found. The SEM study of the chars revealed that during the devolatilization period the particles fuse and the macroporosity and thus the morphotypes are formed. After devolatilization ceases, secondary micropores are formed. These develop in number and size throughout the medium combustion interval. At the end of the combustion interval the macrostructure breaks down, caused by coalescence of the increased number of microspores. This can be observed as a change in the morphology and the macroporosity of the chars. Results indicate that char reactivity is a function of the macroporosity and thus the morphology of combustion chars. (AB) 34 refs.

  20. Demonstration of Active Combustion Control

    Science.gov (United States)

    Lovett, Jeffrey A.; Teerlinck, Karen A.; Cohen, Jeffrey M.

    2008-01-01

    The primary objective of this effort was to demonstrate active control of combustion instabilities in a direct-injection gas turbine combustor that accurately simulates engine operating conditions and reproduces an engine-type instability. This report documents the second phase of a two-phase effort. The first phase involved the analysis of an instability observed in a developmental aeroengine and the design of a single-nozzle test rig to replicate that phenomenon. This was successfully completed in 2001 and is documented in the Phase I report. This second phase was directed toward demonstration of active control strategies to mitigate this instability and thereby demonstrate the viability of active control for aircraft engine combustors. This involved development of high-speed actuator technology, testing and analysis of how the actuation system was integrated with the combustion system, control algorithm development, and demonstration testing in the single-nozzle test rig. A 30 percent reduction in the amplitude of the high-frequency (570 Hz) instability was achieved using actuation systems and control algorithms developed within this effort. Even larger reductions were shown with a low-frequency (270 Hz) instability. This represents a unique achievement in the development and practical demonstration of active combustion control systems for gas turbine applications.

  1. Combustion instability modeling and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Santoro, R.J.; Yang, V.; Santavicca, D.A. [Pennsylvania State Univ., University Park, PA (United States)] [and others

    1995-10-01

    It is well known that the two key elements for achieving low emissions and high performance in a gas turbine combustor are to simultaneously establish (1) a lean combustion zone for maintaining low NO{sub x} emissions and (2) rapid mixing for good ignition and flame stability. However, these requirements, when coupled with the short combustor lengths used to limit the residence time for NO formation typical of advanced gas turbine combustors, can lead to problems regarding unburned hydrocarbons (UHC) and carbon monoxide (CO) emissions, as well as the occurrence of combustion instabilities. Clearly, the key to successful gas turbine development is based on understanding the effects of geometry and operating conditions on combustion instability, emissions (including UHC, CO and NO{sub x}) and performance. The concurrent development of suitable analytical and numerical models that are validated with experimental studies is important for achieving this objective. A major benefit of the present research will be to provide for the first time an experimentally verified model of emissions and performance of gas turbine combustors.

  2. COMBUSTION SIMULATION IN A SPARK IGNITION ENGINE CYLINDER: EFFECTS OF AIR-FUEL RATIO ON THE COMBUSTION DURATION

    OpenAIRE

    2010-01-01

    Combustion is an important subject of internal combustion engine studies. To reduce the air pollution from internal combustion engines and to increase the engine performance, it is required to increase combustion efficiency. In this study, effects of air/fuel ratio were investigated numerically. An axisymmetrical internal combustion engine was modeled in order to simulate in-cylinder engine flow and combustion. Two dimensional transient continuity, momentum, turbulence, energy, and combustion...

  3. Co-Combustion of Animal Waste in a Commercial Waste-to-Energy BFB Boiler

    Directory of Open Access Journals (Sweden)

    Farzad Moradian

    2013-11-01

    Full Text Available Co-combustion of animal waste, in waste-to-energy boilers, is considered a method to produce both heat and power and to dispose of possibly infected animal wastes. This research conducted full-scale combustion tests to identify the impact of changed fuel composition on a fluidized-bed boiler. The impact was characterized by analyzing the deposit formation rate, deposit composition, ash composition, and emissions. Two combustion tests, denoted the reference case and animal waste case, were performed based on different fuel mixes. In the reference case, a normal solid waste fuel mix was combusted in the boiler, containing sorted industry and household waste. In the animal waste case, 20 wt% animal waste was added to the reference fuel mix. The collected samples, comprising sampling probe deposits, fuel mixes, bed ash, return sand, boiler ash, cyclone ash and filter ash, were analyzed using chemical fractionation, SEM-EDX and XRD. The results indicate decreased deposit formation due to animal waste co-combustion. SEM-EDX and chemical fractionation identified higher concentrations of P, Ca, S, and Cl in the bed materials in the animal waste case. Moreover, the risk of bed agglomeration was lower in the animal waste case and also a decreased rate of NOx and SO2 emissions were observed.

  4. Liquid propellant rocket engine combustion simulation with a time-accurate CFD method

    Science.gov (United States)

    Chen, Y. S.; Shang, H. M.; Liaw, Paul; Hutt, J.

    1993-01-01

    Time-accurate computational fluid dynamics (CFD) algorithms are among the basic requirements as an engineering or research tool for realistic simulations of transient combustion phenomena, such as combustion instability, transient start-up, etc., inside the rocket engine combustion chamber. A time-accurate pressure based method is employed in the FDNS code for combustion model development. This is in connection with other program development activities such as spray combustion model development and efficient finite-rate chemistry solution method implementation. In the present study, a second-order time-accurate time-marching scheme is employed. For better spatial resolutions near discontinuities (e.g., shocks, contact discontinuities), a 3rd-order accurate TVD scheme for modeling the convection terms is implemented in the FDNS code. Necessary modification to the predictor/multi-corrector solution algorithm in order to maintain time-accurate wave propagation is also investigated. Benchmark 1-D and multidimensional test cases, which include the classical shock tube wave propagation problems, resonant pipe test case, unsteady flow development of a blast tube test case, and H2/O2 rocket engine chamber combustion start-up transient simulation, etc., are investigated to validate and demonstrate the accuracy and robustness of the present numerical scheme and solution algorithm.

  5. TOXIC SUBSTANCES FROM COAL COMBUSTION

    Energy Technology Data Exchange (ETDEWEB)

    A KOLKER; AF SAROFIM; CL SENIOR; FE HUGGINS; GP HUFFMAN; I OLMEZ; J LIGHTY; JOL WENDT; JOSEPH J HELBLE; MR AMES; N YAP; R FINKELMAN; T PANAGIOTOU; W SEAMES

    1998-12-08

    The Clean Air Act Amendments of 1990 identify a number of hazardous air pollutants (HAPs) as candidates for regulation. Should regulations be imposed on HAP emissions from coal-fired power plants, a sound understanding of the fundamental principles controlling the formation and partitioning of toxic species during coal combustion will be needed. With support from the Federal Energy Technology Center (FETC), the Electric Power Research Institute, the Lignite Research Council, and VTT (Finland), Physical Sciences Inc. (PSI) has teamed with researchers from USGS, MIT, the University of Arizona (UA), the University of Kentucky (UK), the University of Connecticut (UC), the University of Utah (UU) and the University of North Dakota Energy and Environmental Research Center (EERC) to develop a broadly applicable emissions model useful to regulators and utility planners. The new Toxics Partitioning Engineering Model (ToPEM) will be applicable to all combustion conditions including new fuels and coal blends, low-NO combustion systems, and new power generation x plants. Development of ToPEM will be based on PSI's existing Engineering Model for Ash Formation (EMAF). This report covers the reporting period from 1 July 1998 through 30 September 1998. During this period distribution of all three Phase II coals was completed. Standard analyses for the whole coal samples were also completed. Mössbauer analysis of all project coals and fractions received to date has been completed in order to obtain details of the iron mineralogy. The analyses of arsenic XAFS data for two of the project coals and for some high arsenic coals have been completed. Duplicate splits of the Ohio 5,6,7 and North Dakota lignite samples were taken through all four steps of the selective leaching procedure. Leaching analysis of the Wyodak coal has recently commenced. Preparation of polished coal/epoxy pellets for probe/SEM studies is underway. Some exploratory mercury LIII XAFS work was

  6. Spectral optimization and uncertainty quantification in combustion modeling

    Science.gov (United States)

    Sheen, David Allan

    become available, and it will be desirable to know the effect that inclusion of these data has on the optimized model. Two cases are considered here. In the first, a study of H2/CO mass burning rates has recently been published, wherein the experimentally-obtained results could not be reconciled with any extant H2/CO oxidation model. It is shown in that an optimized H2/CO model can be developed that will reproduce the results of the new experimental measurements. In addition, the high precision of the new experiments provide a strong constraint on the reaction rate parameters of the chemistry model, manifested in a significant improvement in the precision of simulations. In the second case, species time histories were measured during n-heptane oxidation behind reflected shock waves. The highly precise nature of these measurements is expected to impose critical constraints on chemical kinetic models of hydrocarbon combustion. The results show that while an as-compiled, prior reaction model of n-alkane combustion can be accurate in its prediction of the detailed species profiles, the kinetic parameter uncertainty in the model remains to be too large to obtain a precise prediction of the data. Constraining the prior model against the species time histories within the measurement uncertainties led to notable improvements in the precision of model predictions against the species data as well as the global combustion properties considered. Lastly, we show that while the capability of the multispecies measurement presents a step-change in our precise knowledge of the chemical processes in hydrocarbon combustion, accurate data of global combustion properties are still necessary to predict fuel combustion.

  7. Sandia Combustion Research Program: Annual report, 1986

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    This report presents research results of the past year, divided thematically into some ten categories. Publications and presentations arising from this work are included in the appendix. Our highlighted accomplishment of the year is the announcement of the discovery and demonstration of the RAPRENOx process. This new mechanism for the elimination of nitrogen oxides from essentially all kinds of combustion exhausts shows promise for commercialization, and may eventually make a significant contribution to our nation's ability to control smog and acid rain. The sections of this volume describe the facility's laser and computer system, laser diagnostics of flames, combustion chemistry, reacting flows, liquid and solid propellant combustion, mathematical models of combustion, high-temperature material interfaces, studies of engine/furnace combustion, coal combustion, and the means of encouraging technology transfer. 182 refs., 170 figs., 12 tabs.

  8. Straw combustion on slow-moving grates

    DEFF Research Database (Denmark)

    Kær, Søren Knudsen

    2005-01-01

    Combustion of straw in grate-based boilers is often associated with high emission levels and relatively poor fuel burnout. A numerical grate combustion model was developed to assist in improving the combustion performance of these boilers. The model is based on a one-dimensional ‘‘walking......-column’’ approach and includes the energy equations for both the fuel and the gas accounting for heat transfer between the two phases. The model gives important insight into the combustion process and provides inlet conditions for a computational fluid dynamics analysis of the freeboard. The model predictions...... indicate the existence of two distinct combustion modes. Combustion air temperature and mass flow-rate are the two parameters determining the mode. There is a significant difference in reaction rates (ignition velocity) and temperature levels between the two modes. Model predictions were compared...

  9. Experimental research on combustion fluorine retention using calcium-based sorbets during coal combustion (Ⅰ)

    Institute of Scientific and Technical Information of China (English)

    QI Qing-jie; LIN Zhi-yan; LIU Jian-zhong; WU Xian; ZHOU Jun-hu; CEN Ke-fa

    2008-01-01

    In order to provide experimental guide to commercial use of fluorine pollution control during coal combustion, with fluorine pollution control during coal combustion in mind, this paper proposed the theory of combustion fluorine retention technology. Feasibility of fluorine retention reaction with calcium-based fluorine retention agent was analyzed through thermo-dynamic calculation during coal combustion. By simulating the restraining and retention effects and influential factors of calcium-based sorbets on vaporized fluoride during experimental combustion using fixed bed tube furnace, the paper systematically explored the influential law of such factors as combustion temperature, retention time, and added quantities of calcium-based sorbets on effects of fluorine retention. The research result shows that adding calcium-based fluorine retention agent in coal combustion has double effects of fluorine retention and sulfur retention, it lays an experimental foundation for commercial test of combustion fluorine retention.

  10. Fuel combustion test in constant volume combustion chamber with built-in adaptor

    Institute of Scientific and Technical Information of China (English)

    JEONG; DongSoo; CHO; GyuBack; CHOI; SuJin; LEE; JinSoo

    2010-01-01

    Combustion tests of pre-mixture of methane and air in constant volume combustion chamber(CVCC) have been carried out by means of flame propagation photo and gas pressure measurement,the effects of CVCC body temperature,intake pressure of pre-mixture of methane and air,equivalence ratio and location of the built-in adaptor have been investigated.The whole combustion chamber can be divided into two parts,i.e.the upper combustion chamber and the lower combustion chamber,by the built-in adaptor with through hole.Owing to the built-in adaptor with through hole,jet ignition or compression ignition(auto-ignition) phenomena may occur in the lower combustion chamber,which is helpful to getting higher flame propagation velocity,higher combustion peak pressure,low cycle-to-cycle variation and more stable combustion process.

  11. Investigation of thermal and environmental characteristics of combustion of gaseous fuels

    Science.gov (United States)

    Vetkin, A. V.; Suris, A. L.

    2015-03-01

    Numerical investigations are fulfilled for some thermal and environmental characteristics of combustion of gaseous fuels used at present in tube furnaces of petroleum refineries. The effect of the fuel composition on these characteristics is shown and probable consequences of the substitution of natural gas to other types of fuels. Methane, ethane, propane, butane, propylene, and hydrogen are considered for comparison, which in most cases are constituents of the composition of the fuel burnt in furnaces. The effect of the fuel type, its associated combustion temperature, combustion product emissivity, temperature of combustion chamber walls, mean beam length, and heat release on the variation in the radiant heat flux within the radiant chamber of furnaces is investigated. The effect of flame characteristics, which are determined by the presence of diffusion combustion zones formed by burners used at present in furnaces for reducing nitrogen oxides emission, is analyzed. The effect of the fuel type on the equilibrium NO concentration is also investigated. The investigations were carried out both at arbitrary given gas temperatures and at effective temperatures dependent on the adiabatic combustion temperature and the temperature at the chamber output and determined based on solving a set of equations at various heat-release rates of the combustion chamber.

  12. Measure Guideline: Combustion Safety for Natural Draft Appliances Using Indoor Air

    Energy Technology Data Exchange (ETDEWEB)

    Brand, L. [Partnership for Advanced Residential Retrofit, Des Plaines, IL (United States)

    2014-04-01

    This measure guideline covers how to assess and carry out the combustion safety procedures for appliances and heating equipment that uses indoor air for combustion in low-rise residential buildings. Only appliances installed in the living space, or in an area freely communicating with the living space, vented alone or in tandem with another appliance are considered here. A separate measure guideline addresses combustion appliances located either within the living space in enclosed closets or side rooms or outside the living space in an adjacent area like an attic or garage that use outdoor air for combustion. This document is for inspectors, auditors, and technicians working in homes where energy upgrades are being conducted whether or not air infiltration control is included in the package of measures being applied. In the indoor combustion air case, guidelines summarized here are based on language provided in several of the codes to establish minimum requirements for the space using simplified prescriptive measures. In addition, building performance testing procedures are provided by testing agencies. The codes in combination with the test procedures offer comprehensive combustion safety coverage to address safety concerns, allowing inexperienced residential energy retrofit inspectors to effectively address combustion safety issues and allow energy retrofits to proceed.

  13. Optical and chemical characterization of aerosols emitted from coal, heavy and light fuel oil, and small-scale wood combustion.

    Science.gov (United States)

    Frey, Anna K; Saarnio, Karri; Lamberg, Heikki; Mylläri, Fanni; Karjalainen, Panu; Teinilä, Kimmo; Carbone, Samara; Tissari, Jarkko; Niemelä, Ville; Häyrinen, Anna; Rautiainen, Jani; Kytömäki, Jorma; Artaxo, Paulo; Virkkula, Aki; Pirjola, Liisa; Rönkkö, Topi; Keskinen, Jorma; Jokiniemi, Jorma; Hillamo, Risto

    2014-01-01

    Particle emissions affect radiative forcing in the atmosphere. Therefore, it is essential to know the physical and chemical characteristics of them. This work studied the chemical, physical, and optical characteristics of particle emissions from small-scale wood combustion, coal combustion of a heating and power plant, as well as heavy and light fuel oil combustion at a district heating station. Fine particle (PM1) emissions were the highest in wood combustion with a high fraction of absorbing material. The emissions were lowest from coal combustion mostly because of efficient cleaning techniques used at the power plant. The chemical composition of aerosols from coal and oil combustion included mostly ions and trace elements with a rather low fraction of absorbing material. The single scattering albedo and aerosol forcing efficiency showed that primary particles emitted from wood combustion and some cases of oil combustion would have a clear climate warming effect even over dark earth surfaces. Instead, coal combustion particle emissions had a cooling effect. Secondary processes in the atmosphere will further change the radiative properties of these emissions but are not considered in this study.

  14. Combustion Behavior of Free Boron Slurry Droplets,

    Science.gov (United States)

    2014-09-26

    weak disruptive behavior while pure JP-1t burn quiescently, except for a flash extinction which occurs at the termination of combustion. The...I AD-R158 628 COMBUSTION BEHAVIOR OF FREE BORON SLURRY DROPLETS(U) i/i I PRINCETON UNIV NJ DEPT OF MECHANICAL AND AEROSPACE ENINEERIN., F TAKAHASHI...COMBUSTION BEHAVIOR OF FREE BORON SLURRY DROPLETS TAM by F. Takahashi, F.L. Dryer, and F.A. Williams Department of M~echanical and keyosase Engineering

  15. Materials for High-Temperature Catalytic Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Ersson, Anders

    2003-04-01

    Catalytic combustion is an environmentally friendly technique to combust fuels in e.g. gas turbines. Introducing a catalyst into the combustion chamber of a gas turbine allows combustion outside the normal flammability limits. Hence, the adiabatic flame temperature may be lowered below the threshold temperature for thermal NO{sub X} formation while maintaining a stable combustion. However, several challenges are connected to the application of catalytic combustion in gas turbines. The first part of this thesis reviews the use of catalytic combustion in gas turbines. The influence of the fuel has been studied and compared over different catalyst materials. The material section is divided into two parts. The first concerns bimetallic palladium catalysts. These catalysts showed a more stable activity compared to their pure palladium counterparts for methane combustion. This was verified both by using an annular reactor at ambient pressure and a pilot-scale reactor at elevated pressures and flows closely resembling the ones found in a gas turbine combustor. The second part concerns high-temperature materials, which may be used either as active or washcoat materials. A novel group of materials for catalysis, i.e. garnets, has been synthesised and tested in combustion of methane, a low-heating value gas and diesel fuel. The garnets showed some interesting abilities especially for combustion of low-heating value, LHV, gas. Two other materials were also studied, i.e. spinels and hexa aluminates, both showed very promising thermal stability and the substituted hexa aluminates also showed a good catalytic activity. Finally, deactivation of the catalyst materials was studied. In this part the sulphur poisoning of palladium, platinum and the above-mentioned complex metal oxides has been studied for combustion of a LHV gas. Platinum and surprisingly the garnet were least deactivated. Palladium was severely affected for methane combustion while the other washcoat materials were

  16. The combustion of solid fuels and wastes

    CERN Document Server

    Tillman, David

    1991-01-01

    Careful organization and empirical correlations help clarify the prodigious technical information presented in this useful reference.Key Features* Written for practicing engineers, this comprehensive book supplies an overall framework of the combustion process; It connects information on specific reactions and reaction sequences with current applications and hardware; Each major group of combustion solids is evaluated; Among the many topics covered are:* Various biomass forms* The coalification process* Grate, kiln, and suspension firing* Fluidized bed combustion

  17. Basic theory research of coal spontaneous combustion

    Institute of Scientific and Technical Information of China (English)

    WANG Ji-ren; SUN Yan-qiu; ZHAO Qing-fu; DENG Cun-bao; DENG Han-zhong

    2008-01-01

    Discussed latest research results of basic theory research of coal spontaneous combustion in detail, with quantum chemical theory and method and experiment systematically studied chemical structure of coal molecule, adsorption mechanism of coal surface to oxygen molecule and chemical reaction mechanism and process of spontaneous combustion of organic macromolecule and low molecular weight compound in coal from microcosmic view, and established complete theoretical system of the mechanism of coal spontaneous combustion.

  18. Combustion en lit fluidisé Fluidized-Bed Combustion

    Directory of Open Access Journals (Sweden)

    Chrysostome G.

    2006-11-01

    Full Text Available Après quelques rappels généraux sur la fluidisation où seront présentés en par-ticulier les avantages qu'elle offre en combustion, on exposera l'état actuel du développement des générateurs à lit fluidisé opérant avec les combustibles suivants : charbon, combustibles pétroliers, résidus divers ; il sera fait mention de la contribution de l'Institut Français du Pétrole (IFP dans les deux derniers domaines.On présentera ensuite les installations les plus récentes en traitement de minerais (grillage des sulfures, calcination de calcaires. En raison de son importance on examinera encore les possibilités de désulfuration au sein de lits fluidisés, de même que seront commentés les travaux de régénération des absorbants.On terminera enfin en mentionnant les développements des lits circulants ou rapides, considérés comme les réacteurs de la seconde génération. After a general review of fluidization including in particular the advantages it offers for combustion, this article describes the present state of the development of fluidized-bed gcnerators operating with the following fuels : cool, petroleum fuels, different residues. Mention is made of Institut Français du Pétrole (IFP contribution in the last two fields. Then the most recent ore-treating installations are described (roasting of sulfides, calcination of limestones. Because of its importance, the possibilities of desulfurizoticn inside fluidized beds is examined, and research on the regeneration of absorbants is commented on. The article ends by mentioning the development of circulating or fast beds which are considered as second generation reactors.

  19. Combustion of Solid Propellants (La Combustion des Propergols Solides)

    Science.gov (United States)

    1991-07-01

    on peut s’interroger sur l’adquation des moyens engages ausceptiblea do se manifester naturellement au cours du A Ia complexit6 du probl~me... capteur d’Helmoltz; de pression lorsque Ia fr~quence vanet. Calcul num~rique et mithode expdrimentale donnent des irdsultats en bon accord, c’cst-i... naturellement , avec des niveaux stabilis~s moddr~s. mod~le de combustion (r~f. 30) et des limites de L’opinion est r~pandue que la segmentation peut l’approche

  20. High Frequency Combustion Instabilities of LOx/CH4 Spray Flames in Rocket Engine Combustion Chambers

    OpenAIRE

    Sliphorst, M.

    2011-01-01

    Ever since the early stages of space transportation in the 1940’s, and the related liquid propellant rocket engine development, combustion instability has been a major issue. High frequency combustion instability (HFCI) is the interaction between combustion and the acoustic field in the combustion chamber. It destroys the thermal boundary layer wall increasing heat transfer and could lead to compromised performance, and ultimately to destruction of the engine and mission loss. The main object...

  1. Fuel gas combustion research at METC

    Energy Technology Data Exchange (ETDEWEB)

    Norton, T.S.

    1995-06-01

    The in-house combustion research program at METC is an integral part of many METC activities, providing support to METC product teams, project managers, and external industrial and university partners. While the majority of in-house combustion research in recent years has been focussed on the lean premixed combustion of natural gas fuel for Advanced Turbine Systems (ATS) applications, increasing emphasis is being placed on issues of syngas combustion, as the time approaches when the ATS and coal-fired power systems programs will reach convergence. When the METC syngas generator is built in 1996, METC will have the unique combination of mid-scale pressurized experimental facilities, a continuous syngas supply with variable ammonia loading, and a team of people with expertise in low-emissions combustion, chemical kinetics, combustion modeling, combustion diagnostics, and the control of combustion instabilities. These will enable us to investigate such issues as the effects of pressure, temperature, and fuel gas composition on the rate of conversion of fuel nitrogen to NOx, and on combustion instabilities in a variety of combustor designs.

  2. Secondary combustion device for woodburning stove

    Energy Technology Data Exchange (ETDEWEB)

    Craver, R.D.

    1987-06-16

    This patent describes a wood burning stove including an exhaust flue opening, a combustion chamber for primary combustion having an access door, a support for wood to be burnt and a primary air inlet means for supplying air to support primary combustion of the wood to produce flue gases containing combustible particulate material. A conduit means for directing the flue gases is included from the combustion chamber to the flue opening in a preselected path. Also included is a secondary combustion means for burning particulate material in flue gases before flue gases pass through the exhaust flue opening. The improvement comprises: secondary combustion means including an elongated manifold extending laterally across and above the combustion chamber at a preselected position on the preselected path; a number of air openings spaced longitudinally along the manifold and facing the path of the flue gases and an air inlet means for supplying ambient; secondary combustion air to the manifold for flow from openings into the path of the flue gases in distinct jets; and a laterally elongated passageway above the manifold with upper and lower portions and defined at its upper portion by a sheet metal wall, and a layer of extremely low heat conducting insulation in the passageway. On the sheet metal wall the layer of insulation prevents appreciable conduction of heat from the passageway into the sheet metal wall and flue gases flow through the passageway and from passageway in a generally wide thin flow pattern.

  3. Determining Heats of Combustion of Gaseous Hydrocarbons

    Science.gov (United States)

    Singh, Jag J.; Sprinkle, Danny R.; Puster, Richard L.

    1987-01-01

    Enrichment-oxygen flow rate-ratio related to heat of combustion. Technique developed for determining heats of combustion of natural-gas samples. Based on measuring ratio m/n, where m is (volmetric) flow rate of oxygen required to enrich carrier air in which test gas flowing at rate n is burned, such that mole fraction of oxygen in combustion-product gases equals that in carrier air. The m/n ratio directly related to heats of combustion of saturated hydrocarbons present in natural gas.

  4. Usefulness of the INNOVANCE PFA P2Y test cartridge for the detection of patients with congenital defects of the platelet P2Y₁₂ receptor for adenosine diphosphate.

    Science.gov (United States)

    Scavone, Mariangela; Germanovich, Ksenia; Femia, Eti A; Cattaneo, Marco

    2014-02-01

    The platelet function analyzer (PFA)-100 is used in clinical practice to screen patients with bleeding diathesis and suspected defects of primary hemostasis. A new cartridge, INNOVANCE PFA P2Y, has been specifically developed to monitor patients' response to drugs inhibiting the platelet P2Y₁₂ receptor for ADP. In this study, we compared the ability of INNOVANCE PFA P2Y to detect congenital defects of the platelet P2Y₁₂ receptor to that of standard cartridge formulations currently in clinical use. We studied two patients with severe P2Y₁₂ deficiency, one patient with heterozygous P2Y₁₂ deficiency and one with dysfunctional P2Y₁₂ receptor. Closure times were measured using 3 cartridges: collagen/ADP, collagen/epinephrine, and INNOVANCE PFA P2Y. The results obtained in the four patients with P2Y₁₂ defects were compared to those obtained for 20 healthy controls. In 2 patients with severe P2Y₁₂ deficiency, closure times of INNOVANCE PFA P2Y and collagen/ADP cartridges were >300 s, while those of collagen/epinephrine cartridge were variable (186s and >300 s). In the patient with dysfunctional P2Y₁₂, closure time of INNOVANCE PFA P2Y was >300 s, while closure times of collagen/ADP and collagen/epinephrine were normal. Closure times of all cartridges were normal in the patient with heterozygous P2Y₁₂ deficiency. Our study provides the first evidence that INNOVANCE PFA P2Y cartridge is sensitive to congenital severe and moderate defects of the platelet P2Y₁₂ receptors. Copyright © 2013 Elsevier Ltd. All rights reserved.

  5. The Cartridge Theory: a description of the functioning of horizontal subsurface flow constructed wetlands for wastewater treatment, based on modelling results.

    Science.gov (United States)

    Samsó, Roger; García, Joan

    2014-03-01

    Despite the fact that horizontal subsurface flow constructed wetlands have been in operation for several decades now, there is still no clear understanding of some of their most basic internal functioning patterns. To fill this knowledge gap, on this paper we present what we call "The Cartridge Theory". This theory was derived from simulation results obtained with the BIO_PORE model and explains the functioning of urban wastewater treatment wetlands based on the interaction between bacterial communities and the accumulated solids leading to clogging. In this paper we start by discussing some changes applied to the biokinetic model implemented in BIO_PORE (CWM1) so that the growth of bacterial communities is consistent with a well-known population dynamics models. This discussion, combined with simulation results for a pilot wetland system, led to the introduction of "The Cartridge Theory", which states that the granular media of horizontal subsurface flow wetlands can be assimilated to a generic cartridge which is progressively consumed (clogged) with inert solids from inlet to outlet. Simulations also revealed that bacterial communities are poorly distributed within the system and that their location is not static but changes over time, moving towards the outlet as a consequence of the progressive clogging of the granular media. According to these findings, the life-span of constructed wetlands corresponds to the time when bacterial communities are pushed as much towards the outlet that their biomass is not anymore sufficient to remove the desirable proportion of the influent pollutants. Copyright © 2013 Elsevier B.V. All rights reserved.

  6. Pulsed atmospheric fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    1989-11-01

    In order to verify the technical feasibility of the MTCI Pulsed Atmospheric Fluidized Bed Combustor technology, a laboratory-scale system was designed, built and tested. Important aspects of the operational and performance parameters of the system were established experimentally. A considerable amount of the effort was invested in the initial task of constructing an AFBC that would represent a reasonable baseline against which the performance of the PAFBC could be compared. A summary comparison of the performance and emissions data from the MTCI 2 ft {times} 2 ft facility (AFBC and PAFBC modes) with those from conventional BFBC (taller freeboard and recycle operation) and circulating fluidized bed combustion (CFBC) units is given in Table ES-1. The comparison is for typical high-volatile bituminous coals and sorbents of average reactivity. The values indicated for BFBC and CFBC were based on published information. The AFBC unit that was designed to act as a baseline for the comparison was indeed representative of the larger units even at the smaller scale for which it was designed. The PAFBC mode exhibited superior performance in relation to the AFBC mode. The higher combustion efficiency translates into reduced coal consumption and lower system operating cost; the improvement in sulfur capture implies less sorbent requirement and waste generation and in turn lower operating cost; lower NO{sub x} and CO emissions mean ease of site permitting; and greater steam-generation rate translates into less heat exchange surface area and reduced capital cost. Also, the PAFBC performance generally surpasses those of conventional BFBC, is comparable to CFBC in combustion and NO{sub x} emissions, and is better than CFBC in sulfur capture and CO emissions even at the scaled-down size used for the experimental feasibility tests.

  7. High pressure optical combustion probe

    Energy Technology Data Exchange (ETDEWEB)

    Woodruff, S.D.; Richards, G.A.

    1995-06-01

    The Department of Energy`s Morgantown Energy Technology Center has developed a combustion probe for monitoring flame presence and heat release. The technology involved is a compact optical detector of the OH radical`s UV fluorescence. The OH Monitor/Probe is designed to determine the flame presence and provide a qualitative signal proportional to the flame intensity. The probe can be adjusted to monitor a specific volume in the combustion zone to track spatial fluctuations in the flame. The probe is capable of nanosecond time response and is usually slowed electronically to fit the flame characteristics. The probe is a sapphire rod in a stainless steel tube which may be inserted into the combustion chamber and pointed at the flame zone. The end of the sapphire rod is retracted into the SS tube to define a narrow optical collection cone. The collection cone may be adjusted to fit the experiment. The fluorescence signal is collected by the sapphire rod and transmitted through a UV transmitting, fused silica, fiber optic to the detector assembly. The detector is a side window photomultiplier (PMT) with a 310 run line filter. A Hamamatsu photomultiplier base combined with a integral high voltage power supply permits this to be a low voltage device. Electronic connections include: a power lead from a modular DC power supply for 15 VDC; a control lead for 0-1 volts to control the high voltage level (and therefore gain); and a lead out for the actual signal. All low voltage connections make this a safe and easy to use device while still delivering the sensitivity required.

  8. Combustion char morphology related to combustion temperature and coal petrography

    Energy Technology Data Exchange (ETDEWEB)

    Rosenberg, P.; Petersen, H.I.; Thomsen, E. [Geological Survey of Denmark, Copenhagen (Denmark)

    1996-07-01

    Chars produced from different reactors were found to lack consistency of morphological charactersitics. Therefore, the morphology of chars sampled from various laboratory-scale reactors operating at temperatures from 800 to {gt} 1400{degree}C, together with chars collected directly in the flame zone in a full-scale pulverised fuel combustion experiment, was examined. A coal and coal blend dominated by vitrinite-rich microlithotypes together with four coals dominated by inertinite-rich microlithotypes were used to produce the combustion chars. Char samples produced at temperatures above {approximately} 1300{degree}C have a morphotype composition very similar to the composition of the full-scale char samples, whereas the morphotype compositions of those produced at {approximately} 1550{degree}C or lower are significantly different. Correlation between coal petrography and char morphology and determination of char reactivity should thus be attempted only using chars produced at temperatures comparable with those for the intended use of the coal. A clear distinction between the high-temperature char samples (burnout 50-60wt% daf) emerges which is related mainly to the parent coal petrography and probably secondarily to the rank. Vitrite, clarite and vitrinertie V may be correlated with the porous tenuisphere and crassisphere morphotypes, whereas inertite, durite, vitrinertite I, duroclarite and charodurite may be correlated with the crassinetwork-mixed-network-mixed morphotype group. 29 refs., 7 figs., 7 tabs.

  9. Energy recycling by co-combustion of coal and recovered paint solids from automobile paint operations.

    Science.gov (United States)

    Suriyawong, Achariya; Magee, Rogan; Peebles, Ken; Biswas, Pratim

    2009-05-01

    During the past decade, there has been substantial interest in recovering energy from many unwanted byproducts from industries and municipalities. Co-combustion of these products with coal seems to be the most cost-effective approach. The combustion process typically results in emissions of pollutants, especially fine particles and trace elements. This paper presents the results of an experimental study of particulate emission and the fate of 13 trace elements (arsenic [As], barium [Ba], cadmium [Cd], chromium [Cr], copper [Cu], cobalt [Co], manganese [Mn], molybdenum [Mo], nickel [Ni], lead [Pb], mercury [Hg], vanadium [V], and zinc [Zn]) during combustion tests of recovered paint solids (RPS) and coal. The emissions from combustions of coal or RPS alone were compared with those of co-combustion of RPS with subbituminous coal. The distribution/partitioning of these toxic elements between a coarse-mode ash (particle diameter [dp] > 0.5 microm), a submicrometer-mode ash (dp burning particles and the higher volatile chlorine species. Hg was completely volatilized in all cases; however, the fraction in the oxidized state increased with co-combustion. Most trace elements, except Zn, were retained in ash during combustion of RPS alone. Mo was mostly retained in all samples. The behavior of elements, except Mn and Mo, varied depending on the fuel samples. As, Ba, Cr, Co, Cu, and Pb were vaporized to a greater extent from cocombustion of RPS and coal than from combustion of either fuel. Evidence of the enrichment of certain toxic elements in submicrometer particles has also been observed for As, Cd, Cr, Cu, and Ni during co-combustion.

  10. Theoretical studies of combustion dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Bowman, J.M. [Emory Univ., Atlanta, GA (United States)

    1993-12-01

    The basic objectives of this research program are to develop and apply theoretical techniques to fundamental dynamical processes of importance in gas-phase combustion. There are two major areas currently supported by this grant. One is reactive scattering of diatom-diatom systems, and the other is the dynamics of complex formation and decay based on L{sup 2} methods. In all of these studies, the authors focus on systems that are of interest experimentally, and for which potential energy surfaces based, at least in part, on ab initio calculations are available.

  11. COMBUSTION PROPERTIES OF EUCALYPTUS WOOD

    Directory of Open Access Journals (Sweden)

    Yalçın ÖRS

    1999-03-01

    Full Text Available In this study, the combustion properties of some impregnation materials (abiotic and biotic factors used for eucalyptus wood in interior or exterior environments were investigated. The experimental samples were prepared from Eucalyptus wood based on ASTM-D-1413-76 Tanalith-CBC, boric acid, borax, vacsol-WR, immersol-WR, polyethylen glycole-400 and ammonium sulphate were used as an impregnation material. The results indicated that, vacuum treatment on Eucalyptus gave the lowest retention value of salts. Compounds containing boron+salt increased fire resistance however water repellents decreased the wood flammability.

  12. Particle emissions from biomass combustion

    Science.gov (United States)

    Chabadová, Jana; Papučík, Štefan; Nosek, Radovan

    2014-08-01

    The paper presents an analysis of the impact of fuel feed to power and emissions parameters of the automatic domestic boiler for combustion of wood pellets. For the analysis has been proposed an experimental methodology of boiler measuring. The investigated boiler is designed for operation in domestic heating system. It has heat power equal to 18 kW. Concentrations of flue gas species were registered at the exit the boiler and based on the measured parameters was carried out evaluation of the impact of the fuel feed to heat power and production of emissions.

  13. Design of a new cartridge for selective solid phase extraction using molecularly imprinted polymers: selective extraction of theophylline from human serum samples.

    Science.gov (United States)

    Khorrami, Afshin Rajabi; Rashidpur, Amene

    2009-11-15

    This paper describes design of a new cartridge for selective solid phase extraction (SPE) using molecularly imprinted polymers (MIPs). The apparatus which is termed solvent extraction-MISPE (SE-MISPE) cartridge, consisted of a modified conventional micro test tube and has been developed to perform simultaneous forward-extraction of analyte from aqueous sample solution to an organic phase and back-extraction to MIP solid phase. In order to evaluate the performance of the proposed method, extraction of theophylline (THP) from human serum sample was investigated. An appropriate amount of THP-imprinted polymer was placed in the bottom of the micro tube and an organic solvent pipetted onto it and left to swell the polymer completely. A polyethylene frit to secure MIP particles was positioned by two Teflon rings such that it was fixed below the level of the organic layer. Then, aqueous sample solution containing THP was layered over the organic phase and the lid was closed. After completion of extraction, the organic and aqueous phases were removed and the adsorbed analyte was desorbed using a polar organic solvent. In order to reach the highest recovery, the experimental parameters such as the type of organic solvent, pH and ionic strength of aqueous phase, organic to aqueous volume ratio, time of extraction, type and amount of desorbent solvent were optimized. Under the experimental conditions, a plot of HPLC peak areas vs. initial concentrations of THP in the concentration interval of 0.5-30 microg ml(-1) showed a good linearity (r=0.9974). The limit of detection (LOD) and limit of quantification (LOQ) based on three and ten times of the noise of HPLC profile were 0.09 and 0.3 microg ml(-1), respectively. The relative standard deviation (RSD) of the proposed method for the extraction and determination of 5 microg THP from 200 microl standard sample solution for 3 replicate measurements was 3.5%. The results showed that by means of the proposed cartridge, THP could

  14. Integrated quality control: implementation and validation of instrument function checks and procedural controls for a cartridge-based point-of-care system for critical care analysis.

    Science.gov (United States)

    D'Orazio, Paul; Mansouri, Sohrab

    2013-03-01

    In this article, the process used to develop and validate an integrated quality-control system for a cartridge-based, point-of-care system for critical care analysis is outlined. Application of risk management principles has resulted in a quality control system using a combination of statistical quality control with onboard reference solutions and failure pattern recognition used to flag common failure modes during the analytical phase of the testing process. A combination of traditional external quality control, integrated quality control to monitor ongoing instrument functionality, operator training, and other laboratory-implemented monitors is most effective in controlling known failure modes during the testing process.

  15. The stability of non-ionic surfactants and linear alkylbenzene sulfonates in a water matrix and on solid-phase extraction cartridges.

    Science.gov (United States)

    Petrović, M; Barceló, D

    2000-12-01

    The stability of nonylphenol ethoxylates (NPEO), alcohol ethoxylates (AEO), coconut diethanol amides (CDEA) and linear alkylbenzene sulfonates (LAS) in a water matrix and preconcentrated on SPE cartridges was studied. A stability study was carried out in a water matrix (spiked ground water and real-world waste water) comparing different pretreatment procedures (addition of sulfuric acid to pH = 3, preservation with 1% and 3% of formaldehyde). When stored in a water matrix serious qualitative and quantitative changes occurred in waste water during the period of time studied (30 days). The losses of C12-C14 alcohol ethoxylates ranged from 72% to 88% when the sample was preserved with acid and from 17% to 86% when the sample was preserved with formaldehyde (3%). Simultaneously, an enrichment of the shorter alkyl chain homologues (C7EO and C10EO) was observed. The losses of NPEO were from 45% (sample preserved by acidification or by addition of 3% of formaldehyde) to 85% (sample preserved with 1% of formaldehyde). Additionally, an increase in concentration of polyethylene glycols (PEGs) and formation of different acidic forms, such as monocarboxylated (MCPEGs) and dicarboxylated polyethylene glycols (DCPEGs) were observed. The stability of surfactants preconcentrated on SPE cartridges was studied as a function of storage time and storage conditions (room temperature, 4 degrees C and -20 degrees C). The results indicate that disposable SPE cartridges can be recommended for the stabilization of non-ionic surfactants and LAS. Storage at -20 degrees C is feasible for long periods (up to 3 months for ground water and up to 2 months for waste water), while storage at 4 C can be recommended for a maximum of 1 month. When cartridges were kept at -20 degrees C the losses of AEOs (n = 12, 13 and 14), preconcentrated from waste water, ranged from 17 to 29% (after 60 days) and other compounds suffered small losses (maximum of 14% for C13LAS). At room temperature, after 7 days, the

  16. Effects of disordered microstructure and heat release on propagation of combustion front

    Directory of Open Access Journals (Sweden)

    Naine Tarun Bharath

    2016-05-01

    Full Text Available Numerical experiments for diagnosis of combustion of actual heterogeneous systems is performed on a one dimensional chain. The internal microstructure of actual heterogeneous systems is apriori unknown, various distributions like uniform, beta and normal have been considered for distributing neighboring reaction cells. Two cases, for the nature of distribution of heat release of reaction cells are taken into account, one with identical heat release and the other with disordered heat release. Role of different random distributions in describing heterogeneous combustion process are established in present paper. Particularly the normal distribution of arranging neighboring reaction cells has been found to be powerful methodology in explaining the combustion process of an actual heterogeneous system at higher ignition temperatures for both cases of distributing heat release. Validation of developed model with the experimental data of combustion of the CMDB propellants, gasless Ti+xSi system and different thermite mixtures is performed. Our results show that the experimental burning rates at higher ignition temperatures (ε>0.32 of the heterogeneous system are better reproduced theoretically with present model. We have also shown that different combustion limit for different thermite systems are the consequences of disordered heat release. Experimental data for thermite systems that have lower inflammability limits are analyzed in the view of disordered heat releases of cells. The model developed in the view of disordered heat releases reproduces the experimental burn rates and experimental combustion limit.

  17. An optimization approach to kinetic model reduction for combustion chemistry

    CERN Document Server

    Lebiedz, Dirk

    2013-01-01

    Model reduction methods are relevant when the computation time of a full convection-diffusion-reaction simulation based on detailed chemical reaction mechanisms is too large. In this article, we review a model reduction approach based on optimization of trajectories and show its applicability to realistic combustion models. As most model reduction methods, it identifies points on a slow invariant manifold based on time scale separation in the dynamics of the reaction system. The numerical approximation of points on the manifold is achieved by solving a semi-infinite optimization problem, where the dynamics enter the problem as constraints. The proof of existence of a solution for an arbitrarily chosen dimension of the reduced model (slow manifold) is extended to the case of realistic combustion models including thermochemistry by considering the properties of proper maps. The model reduction approach is finally applied to three models based on realistic reaction mechanisms: 1. ozone decomposition as a small t...

  18. Combustion of TNT products in a confined explosion

    Energy Technology Data Exchange (ETDEWEB)

    Ferguson, R E; Kuhl, A L; Oppenheim, A K

    1999-06-18

    The effects of turbulent combustion of detonation products gases in a confined explosion are explored via laboratory experiments and high-resolution numerical simulations. The expanded products from the detonation of a TNT charge are rich in C and CO, which act as a fuel. When these hot gases mix with air, they are oxidized to CO2--thereby releasing 2482 Cal/g in addition to the 1093 Cal/g deposited by the detonation wave. In this case, the exothermic power is controlled by the turbulent mixing rate, rather than by chemistry. A kinetic law of turbulent combustion is suggested for this process. Pressure histories from the numerical simulations were in good agreement with the experimental measurements--demonstrating that the numerical model contains the fundamental mechanism that controls the exothermic process.

  19. Fire hazards of exterior wall assemblies containing combustible components

    Directory of Open Access Journals (Sweden)

    White Nathan

    2013-11-01

    Full Text Available The Fire Protection Research Foundation has funded a research project on “fire hazards of exterior wall assemblies containing combustible composites”. This paper presents preliminary findings from the project. In particular, statistics relating to exterior wall fires have been reviewed. Exterior wall fires appear to account for somewhere between 1.3% and 3% of structure fires in the selected property types investigated. Fires involving combustible exterior wall assemblies are low frequency events however the resulting consequences in terms of extent of fire spread and injuries and fatalities can be large as demonstrated by selected fire incident case studies. An overview of this project and it's further work is provided.

  20. Combustion chemistry and formation of pollutants; Chimie de la combustion et formation des polluants

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    This book of proceedings reports on 7 papers on combustion chemistry and formation of pollutants presented during the workshop organized by the `Combustion and Flames` section of the French society of thermal engineers. The chemistry of combustion is analyzed in various situations such as: turbojet engines, spark ignition engines, industrial burners, gas turbines etc... Numerical simulation is used to understand the physico-chemical processes involved in combustion, to describe the kinetics of oxidation, combustion and flame propagation, and to predict the formation of pollutants. (J.S.)

  1. Three-dimensional Numerical Simulation of Combustion Field in the Combustion Chamber

    Institute of Scientific and Technical Information of China (English)

    YAN Ping; QIAN Zhi-bo; YANG Jie; ZHANG Jin-jun

    2006-01-01

    In order to study the effect of rotation on the combustion in the underwater vehicle, a two-phase turbulent combustion process is described with Reynolds stress turbulence model, eddy-dissipation turbulent combustion model, P-1 radiation model and particle tracking model of liquid. The flow in the rotating combustion chamber is simulated at two different working speeds, 0 r/min and 1 000 r/min by Fluent software. The temperature, gas velocity, static pressure of wall and fuel concentration are computed and compared. The results show that the combustion in rotating combustor is faster and more effective.

  2. Lung X-ray changes in skeletal fluorosis caused by coal combustion

    Energy Technology Data Exchange (ETDEWEB)

    Liu, B.K. [Hubei Sanitary-Epidemiological Station, Wuhan (China)

    1996-02-01

    Lung X-ray findings are reported in 45 cases with skeletal fluorosis in an area contaminated by coal combustion. The findings include chronic bronchitis, with diffuse interstitial fibrosis and pulmonary emphysema. The degree of pulmonary pathological findings and skeletal fluorosis is correlated with patient age. Among the 45 cases were 5 with cardio-pulmonary disease and 5 with tuberculosis.

  3. Database of Small Molecule Thermochemistry for Combustion

    KAUST Repository

    Goldsmith, C. Franklin

    2012-09-13

    High-accuracy ab initio thermochemistry is presented for 219 small molecules relevant in combustion chemistry, including many radical, biradical, and triplet species. These values are critical for accurate kinetic modeling. The RQCISD(T)/cc-PV∞QZ//B3LYP/6-311++G(d,p) method was used to compute the electronic energies. A bond additivity correction for this method has been developed to remove systematic errors in the enthalpy calculations, using the Active Thermochemical Tables as reference values. On the basis of comparison with the benchmark data, the 3σ uncertainty in the standard-state heat of formation is 0.9 kcal/mol, or within chemical accuracy. An uncertainty analysis is presented for the entropy and heat capacity. In many cases, the present values are the most accurate and comprehensive numbers available. The present work is compared to several published databases. In some cases, there are large discrepancies and errors in published databases; the present work helps to resolve these problems. © 2012 American Chemical Society.

  4. Vapor-phase combustion and heat and mass transfer during the interaction of a high-temperature gas flow with a solid

    Energy Technology Data Exchange (ETDEWEB)

    Pushkin, V.N.; Sukhov, G.S.; Iarin, L.P.

    1988-08-01

    The problem of the combustion of a solid in incoming gas flow containing an oxidizer is solved by using an analytical model allowing for phase transitions and chemical transformations and assuming a quasi-equilibrium state on the free surface and diffusion combustion at the flame front. The hydrodynamic, temperature, and concentration fields are investigated for the case of flow past a body with a spherical nose. The principal combustion characteristics are determined as a function of the incoming flow intensity. 6 references.

  5. Hydrogen Internal Combustion Stirling Engine

    Science.gov (United States)

    Takahashi, Sanyo; Morita, Hiroyuki; Kurata, Osamu; Yamashita, Iwao

    The hydrogen combustion Stirling engine utilizes internal combustion of a stoichiometric H2 and O2 mixture injected into the working gas as thermal input, and the cyclic operation is completed with the removal of water from the engine after condensation at the cooler. In the prototype engine, a catalytic combustor is substituted for the conventional heater, and the H2-O2 mixture is injected at a constant flow rate from the boundary between the regenerator and the cooler. The engine internal heating characteristics were compared to those on external heating to clarify the internal heating effect on the engine performance. The internal heating performance showed almost the same characteristics as those of external heating, except for the increase of expansion work due to the direct thermal input. The increase of expansion work improved the engine performance, particularly in the region of high engine speed. Furthermore, it was found that the steady injection method was able to suppress the mixture strength to a relatively low level.

  6. TECHNOLOGY DEMONSTRATION SUMMARY: THE AMERICAN COMBUSTION PYRETRON THERMAL DESTRUCTION SYSTEM AT THE U.S. EPA'S COMBUSTION FACILITY

    Science.gov (United States)

    The American Combustion Pyretron Thermal Destruction System at the U.S. EPA's Combustion Research Facility. Under the auspices of the Superfund Innovative Technology Evaluation, or SITE, program, a critical assessment was made of the American Combustion Pyretron™ oxygen enha...

  7. Numerical Modeling of MILD Combustion at High Pressure to Predict the Optimal Operating Conditions

    KAUST Repository

    Vanteru, Mahendra Reddy

    2017-02-01

    This Chapter presents numerical simulation on MILD combustion operating at high pressure. Influence of preheat and dilution of oxidizer and operating pressure on stabilization of MILD combustion are presented. Three different preheat temperatures (1100, 1300 and 1500 K) and three different dilution levels (3, 6 and 9% O2) are simulated over an operating pressure variation from 1 atm to 16 atm. A classical jet in hot coflow burner is considered for this study. Total of 45 cases are simulated and analyzed. Essential characteristics of MILD combustion, i.e., maximum temperature $$ (T_{max} ) $$, temperature rise $$ (\\\\Delta T) $$ and temperature distributions, are analyzed. The distribution of emissions OH and CO are also studied and presented. Well-stabilized MILD combustion is observed for all cases except for two cases with high preheated (1500 K). Peak temperature is observed to decrease with increasing operating pressure for a given level of preheat and dilution. OH mass faction is reduced with increasing pressure. The CO emissions show little sensitivity to operating pressure. However, CO mass fraction is slightly higher at 1 atm operating pressure as compared to 4 to 16 atm. Since the residence time of reactants increases as the operating pressure increases, well-stabilized MILD combustion is observed for all highly diluted and low temperature preheat cases (3% O2 and 1100 K).

  8. FLARE FLAME INSTABILITY AND BURNER COMBUSTION CONTROL

    OpenAIRE

    БОНДАРЕНКО А.В.; В. Э. Волков; Максимов, М. В.

    2014-01-01

    Research of the flare instability development and the laminar-to-turbulent transition for the flares was executed. It was proved that the effects of viscosity and compressibility have the stabilizing influence on the gas flame. The study of the individual flare stability makes the theoretical basis of the fuel burning technology in combustion chambers and for the burner combustion control.

  9. 30 CFR 57.4104 - Combustible waste.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Combustible waste. 57.4104 Section 57.4104... Control Prohibitions/precautions/housekeeping § 57.4104 Combustible waste. (a) Waste materials, including liquids, shall not accumulate in quantities that could create a fire hazard. (b) Waste or rags containing...

  10. Combustion Limits and Efficiency of Turbojet Engines

    Science.gov (United States)

    Barnett, H. C.; Jonash, E. R.

    1956-01-01

    Combustion must be maintained in the turbojet-engine combustor over a wide range of operating conditions resulting from variations in required engine thrust, flight altitude, and flight speed. Furthermore, combustion must be efficient in order to provide the maximum aircraft range. Thus, two major performance criteria of the turbojet-engine combustor are (1) operatable range, or combustion limits, and (2) combustion efficiency. Several fundamental requirements for efficient, high-speed combustion are evident from the discussions presented in chapters III to V. The fuel-air ratio and pressure in the burning zone must lie within specific limits of flammability (fig. 111-16(b)) in order to have the mixture ignite and burn satisfactorily. Increases in mixture temperature will favor the flammability characteristics (ch. III). A second requirement in maintaining a stable flame -is that low local flow velocities exist in the combustion zone (ch. VI). Finally, even with these requirements satisfied, a flame needs a certain minimum space in which to release a desired amount of heat, the necessary space increasing with a decrease in pressure (ref. 1). It is apparent, then, that combustor design and operation must provide for (1) proper control of vapor fuel-air ratios in the combustion zone at or near stoichiometric, (2) mixture pressures above the minimum flammability pressures, (3) low flow velocities in the combustion zone, and (4) adequate space for the flame.

  11. Sandia combustion research program: Annual report, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Palmer, R.E.; Sanders, B.R.; Ivanetich, C.A. (eds.)

    1988-01-01

    More than a decade ago, in response to a national energy crisis, Sandia proposed to the US Department of Energy a new, ambitious program in combustion research. Our strategy was to apply the rapidly increasing capabilities in lasers and computers to combustion science and technology. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''User Facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative--involving US universities, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions of several research projects which have been stimulated by Working Groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship Program has been instrumental in the success of some of the joint efforts. The remainder of this report presents research results of calendar year 1987, separated thematically into nine categories. Refereed journal articles appearing in print during 1987, along with selected other publications, are included at the end of Section 10. In addition to our ''traditional'' research--chemistry, reacting flow, diagnostics, engine combustion, and coal combustion--you will note continued progress in somewhat recent themes: pulse combustion, high temperature materials, and energetic materials, for example. Moreover, we have just started a small, new effort to understand combustion-related issues in the management of toxic and hazardous materials.

  12. Coal slurry combustion and technology. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    1983-01-01

    Volume II contains papers presented at the following sessions of the Coal Slurry Combustion and Technology Symposium: (1) bench-scale testing; (2) pilot testing; (3) combustion; and (4) rheology and characterization. Thirty-three papers have been processed for inclusion in the Energy Data Base. (ATT)

  13. A method of determining combustion gas flow

    Science.gov (United States)

    Bon Tempi, P. J.

    1968-01-01

    Zirconium oxide coating enables the determination of hot gas flow patterns on liquid rocket injector face and baffle surfaces to indicate modifications that will increase performance and improve combustion stability. The coating withstands combustion temperatures and due to the coarse surface and coloring of the coating, shows the hot gas patterns.

  14. Oxy Coal Combustion at the US EPA

    Science.gov (United States)

    Oxygen enriched coal (oxy-coal) combustion is a developing, and potentially a strategically key technology intended to accommodate direct CO2 recovery and sequestration. Oxy-coal combustion is also intended for retrofit application to existing power plants. During oxy-coal comb...

  15. Internal combustion engines in hybrid vehicles

    NARCIS (Netherlands)

    Mourad, S.; Weijer, C.J.T. van de; Beckman, D.E.

    1998-01-01

    In this paper the use of internal combustion engines in hybrid powertrains is investigated. The substantial difference between the use of internal combustion engines in conventional and in hybrid vehicles mean that engines for hybrid vehicles should be designed specifically for the purpose. At the

  16. Acousto-elastic interaction in combustion chambers

    OpenAIRE

    Huls, Rob Alexander

    2006-01-01

    This thesis deals with the interaction between combustion, acoustics and vibrations with emphasis on frequencies below 500 Hz. Extensive literature is available on the interaction between combustion and acoustics and much work is also available on the interaction between acoustics and vibration. The work presented in this thesis attempts to combine these fields in order to calculate the vibrations of the liner.

  17. Investigation of pressurized combustion and characterization of solid fuels

    Energy Technology Data Exchange (ETDEWEB)

    Aho, M.; Haemaelaeinen, J.; Paakkinen, K. [VTT Energy, Espoo (Finland); Joutsenoja, T. [Tampere Univ. of Technology (Finland)

    1997-10-01

    The objective of the research of Technical Research Centre of Finland (VTT) was to produce results of the effects of pressure and other important parameters on the combustion of pulverized coals using both experimental and theoretical methods. The results can be utilized to model pressurized combustion and to plan pilot-scale reactors. The studied coals were Polish hvb coal, French lignite (Gardanne), German anthracite (Niederberg) and German (Goettelborn) hvb coal. In was originally planned to study also a char of one of these coals. However, anthracite was selected instead of char, because the theoretical studies predicted maximum pressure effect to be found for antracite-type coals (with low reactivity and low content of volatiles). The pulverized coal samples were combusted in an electrically heated, pressurized entrained flow reactor (PEFR), where the experimental conditions were controlled with a high precision. The studied particle size fractions were 100-125 Em and 140-180 Am for anthracite and 140-180 {mu}m for the other coals. The studied things were combustion rates and temperatures of burning particles. Two types of sets of experiments were carried out. In the first case, experimental planning was done and the results were handled with multivariable partial least squares (PLS) method. Gas temperature varied from 1073K to 1473K and pressure from 0.2 MPa to 0.8 MPa. The other variables were PO2 and PCO{sub 2}. Some of the experiments were carried out at conditions prevailing during flue gas recirculation (CO{sub 2} concentration was > 20 vol%). In the second case, oxygen concentration was kept constant ( 10 vol%) and pressure was varied from 0.2 MPa to 0.8 MPa with an interval of 0.1 MPa

  18. Dry low NOx combustion system with pre-mixed direct-injection secondary fuel nozzle

    Science.gov (United States)

    Zuo, Baifang; Johnson, Thomas; Ziminsky, Willy; Khan, Abdul

    2013-12-17

    A combustion system includes a first combustion chamber and a second combustion chamber. The second combustion chamber is positioned downstream of the first combustion chamber. The combustion system also includes a pre-mixed, direct-injection secondary fuel nozzle. The pre-mixed, direct-injection secondary fuel nozzle extends through the first combustion chamber into the second combustion chamber.

  19. Experimental investigation on combustion of hydrogen-oxygen and methane-oxygen mixtures in the medium of low-superheated steam

    Science.gov (United States)

    Pribaturin, N. A.; Fedorov, V. A.; Alekseev, M. V.; Bogomolov, A. R.; Sorokin, A. L.; Azikhanov, S. S.; Shevyrev, S. A.

    2016-05-01

    Experimental data are represented on the investigation of combustion of hydrogen-oxygen and methane-oxygen mixtures in the medium of low-superheated (initial temperature of approximately 150°C) steam at atmospheric pressure. The influence of the ratio of mass flows of the combustible mixture and steam on the qualitative composition of combustion products and the temperature of produced steam is revealed. Main laws for combustion of the hydrogen-oxygen mixture within the steam flow, which affect the completeness of mixture combustion, are determined. Experimental data on the influence of concentrations of the hydrogen-oxygen mixture within the flow of the steam and the combustible mixture upon the completeness of combustion are given. It is found that, when burning the hydrogen-oxygen mixture within the steam flow with a temperature of 1000-1200°C, it is possible using a variation of the combustible mixture flow. At the same time, the volume fraction of noncondensable gases in the produced steam is no more than 2%. It is revealed that there are several combustion modes of the hydrogen-oxygen mixture within the steam flow, in which, in one case, the steam always suppresses combustion and, in another one, detonation of the combustible mixture combustible mixture occurs. It is found that with the excess air factor close to unit, the combustion of the methane-oxygen mixture within steam and the vapor conversion of methane, which result in the appearance of free hydrogen in the produced high-temperature steam, are possible. The description and the principle of the operation of the experimental bench for investigation of combustion of methane-oxygen and hydrogen-oxygen mixtures in the medium of steam are given. Results of experimental investigations of burning fuel and oxygen in the medium of steam are used in the development of a steam superheater for a hightemperature steam turbine.

  20. Combustion characteristics of bamboo-biochars.

    Science.gov (United States)

    Liu, Zhijia; Fei, Benhua; Jiang, Zehui; Liu, Xing'e

    2014-09-01

    Combustion characteristics of biomass are very important to directly utilize as an energy resource. Bamboo was carbonized using a XD-1200N muffle furnace in the nitrogen environment and its combustion characteristics were investigated. Results showed that bamboo-biochars had better combustion characteristics compared to bamboo materials, such as a lower content of moisture and volatiles, a higher energy density, HHV and EHC, a lower H/C and O/C ratios and a shorter TTI. Characteristic peak of bamboo-biochars shifted to higher temperature in thermal decomposition process, indicating a more steady-state burning and a higher combustion efficiency. Bamboo-biochars had a low content of S and N, which was helpful to decrease pollutant emissions. A higher content of K and Na was observed in the ash of bamboo-biochars, resulting in slagging, fouling, corrosion and agglomeration. The data from this research will be very helpful to efficiently design and operate its combustion systems.

  1. Combustion synthesis of advanced composite materials

    Science.gov (United States)

    Moore, John J.

    1993-01-01

    Self-propagating high temperature (combustion) synthesis (SHS), has been investigated as a means of producing both dense and expanded (foamed) ceramic and ceramic-metal composites, ceramic powders and whiskers. Several model exothermic combustion synthesis reactions were used to establish the importance of certain reaction parameters, e.g., stoichiometry, green density, combustion mode, particle size, etc. on the control of the synthesis reaction, product morphology and properties. The use of an in situ liquid infiltration technique and the effect of varying the reactants and their stoichiometry to provide a range of reactant and product species i.e., solids, liquids and gases, with varying physical properties e.g., volatility and thermal conductivity, on the microstructure and morphology of synthesized composite materials is discussed. Conducting the combustion synthesis reaction in a reactive gas environment to take advantage of the synergistic effects of combustion synthesis and vapor phase transport is also examined.

  2. Some characteristics of fine beryllium particle combustion

    Science.gov (United States)

    Davydov, D. A.; Kholopova, O. V.; Kolbasov, B. N.

    2007-08-01

    Beryllium dust will be produced under plasma interaction with beryllium armor of the first wall in ITER. Exothermal reaction of this dust with water steam or air, which can leak into the reactor vacuum chamber in some accidents, gives concern in respect to reactor safety. Results of studies devoted to combustion of fine beryllium particles are reviewed in the paper. A chemically active medium and elevated temperature are prerequisite to the combustion of beryllium particles. Their ignition is hampered by oxide films, which form a diffusion barrier on the particle surface as a result of pre-flame oxidation. The temperature to initiate combustion of particles depends on flame temperature, particle size, composition of combustible mixture, heating rate and other factors. In mixtures enriched with combustible, the flame temperature necessary to ignite individual particles approaches the beryllium boiling temperature.

  3. Combustion Engines Development Mixture Formation, Combustion, Emissions and Simulation

    CERN Document Server

    Schwarz, Christian; Teichmann, Rüdiger

    2012-01-01

    In the development of engines and vehicles it is nowadays standard practice to use commercially available computing programmes for simulation, not only of the transient reaction of vehicles or of the complete driveshaft, but also of the highly unsteady processes in the combustion chamber of an engine. Normally the source code is not available for these computing programmes and it takes too much time to study the respective specifications, so the users often do not have sufficient knowledge about the physical and chemical contents of the approaches that the programmes are based on. We have often been faced with this fact in talks to employees or in discussions during the presentation of results of simulation. Therefore it is our aim to point out different physical and chemical approaches and to show the possibilities and limits of the models used.

  4. Selective and Accurate Determination Method of Propofol in Human Plasma by Mixed-Mode Cation Exchange Cartridge and GC-MS

    Directory of Open Access Journals (Sweden)

    Jae Sung Pyo

    2016-01-01

    Full Text Available A gas chromatography-mass spectrometry (GC-MS method for the determination of propofol in human plasma has been developed and validated. Propofol was extracted from human plasma by using mixed-mode cation exchange/reversed-phase (MCX cartridges. As propofol easily volatilizes during concentration, 100% methanol was injected directly into GC-MS to elute propofol. Despite avoiding concentration process of the eluted solution, lower limit of quantization (LLOQ of propofol was 25 ng/mL. The validated method exhibited good linearity (R2=0.9989 with accuracy and precision −5.8%~11.7% and 3.7%~11.6%, respectively. The other validation parameters, recovery and matrix effect, ranged from 96.6% to 99.4% and 95.3% to 101.4%, respectively. Propofol standard was quantified to evaluate possible loss due to the concentration processes, nitrogen gas and centrifugal vacuum. These two concentration processes resulted in notable decrease in the quantity of propofol, signifying avoiding any concentration processes during propofol quantification. Also, to confirm suitability of the developed method, authentic human plasma samples were analyzed. The selective assay method using MCX cartridge and GC-MS facilitated quantification of propofol in plasma sample accurately by preventing any losses due to the concentration processes.

  5. Selective and Accurate Determination Method of Propofol in Human Plasma by Mixed-Mode Cation Exchange Cartridge and GC-MS.

    Science.gov (United States)

    Pyo, Jae Sung

    2016-01-01

    A gas chromatography-mass spectrometry (GC-MS) method for the determination of propofol in human plasma has been developed and validated. Propofol was extracted from human plasma by using mixed-mode cation exchange/reversed-phase (MCX) cartridges. As propofol easily volatilizes during concentration, 100% methanol was injected directly into GC-MS to elute propofol. Despite avoiding concentration process of the eluted solution, lower limit of quantization (LLOQ) of propofol was 25 ng/mL. The validated method exhibited good linearity (R (2) = 0.9989) with accuracy and precision -5.8%~11.7% and 3.7%~11.6%, respectively. The other validation parameters, recovery and matrix effect, ranged from 96.6% to 99.4% and 95.3% to 101.4%, respectively. Propofol standard was quantified to evaluate possible loss due to the concentration processes, nitrogen gas and centrifugal vacuum. These two concentration processes resulted in notable decrease in the quantity of propofol, signifying avoiding any concentration processes during propofol quantification. Also, to confirm suitability of the developed method, authentic human plasma samples were analyzed. The selective assay method using MCX cartridge and GC-MS facilitated quantification of propofol in plasma sample accurately by preventing any losses due to the concentration processes.

  6. Comparison of the Usefulness of SPE Cartridges for the Determination of β-Blockers and β-Agonists (Basic Drugs in Environmental Aqueous Samples

    Directory of Open Access Journals (Sweden)

    Magda Caban

    2015-01-01

    Full Text Available Even though the methodology used for the determination of β-blockers and β-agonists in environmental samples is based mainly on solid-phase extraction (SPE and gas chromatography or liquid chromatography with mass spectrometric detection, the available literature data on the applied SPE procedures is rather sparse. In this paper such comparison is presented. Moreover, the usefulness of the eight SPE cartridges for the determination of five β-blockers (acebutolol, atenolol, metoprolol, nadolol, and propranolol and two β-agonists (salbutamol and terbutaline in environmental aqueous samples using GC techniques is tested. Among them, three (the trifunction sorbent Strata Screen C, the copolymers LiChrolut EN, and the functionalized copolymer Isolute ENV+ were used for the first time for this purpose. It was confirmed that polystyrene-divinylbenzene-N-vinylpyrrolidone copolymers (PS-DVB-VP, Strata-X, and Oasis HLB cartridges have a better potential than a cation-exchange sorbent for the extraction of the target drugs from environmental water samples. However, it should be stressed out that the direct application of the tested SPE conditions for the analysis of real environmental water samples is not possible, and such parameters, like volume of loading sample, appropriate solvents for washing and elution steps, and so forth, must be optimized again in order to achieve satisfactory recovery values for the target compounds.

  7. Combustion properties of biomass residues rich in phosphorus

    Energy Technology Data Exchange (ETDEWEB)

    Piotrowska, P.

    2012-07-01

    particles. Entrained fine rapeseed cake ash particles also aggravated deposit formation. In order to improve the problematic behaviour two strategies were used: co-combustion and the use of limestone. Three different base fuels were used: bark, wood, and coal. Co-firing of rapeseed cake with a minimum of 60 wt% of bark in a bench-scale BFB reactor increased the defluidization temperatures compared to the pure rapeseed cake case. This was correlated with the increase of the Ca/P molar, which increased with a higher proportion of bark in the fuel mixture. During co-firing with wood in a semi-industrial scale CFB combustor, the addition of limestone was found to be necessary in order to improve the bed sintering tendency of the fuel mixture. Co-firing of rapeseed cake with coal in a semi-industrial CFB combustor did not show any significant operational problems. Therefore co-combustion with coal is considered to be one of the strategies to improve combustion of phosphorus-rich biomass. The experimental work in this study revealed that phosphorus has a role during combustion which cannot be neglected when phosphorus-rich fuels are entering the energy market. Challenges during fluidized bed combustion of the residues were defined and countermeasures were investigated. (orig.)

  8. Nanoparticle emissions from combustion engines

    CERN Document Server

    Merkisz, Jerzy

    2015-01-01

     This book focuses on particulate matter emissions produced by vehicles with combustion engines. It describes the physicochemical properties of the particulate matter, the mechanisms of its formation and its environmental impacts (including those on human beings). It discusses methods for measuring particulate mass and number, including the state-of-the-art in Portable Emission Measurement System (PEMS) equipment for measuring the exhaust emissions of both light and heavy-duty vehicles and buses under actual operating conditions. The book presents the authors’ latest investigations into the relations between particulate emission (mass and number) and engine operating parameters, as well as their new findings obtained through road tests performed on various types of vehicles, including those using diesel particulate filter regeneration. The book, which addresses the needs of academics and professionals alike, also discusses relevant European regulations on particulate emissions and highlights selected metho...

  9. Assembly for directing combustion gas

    Energy Technology Data Exchange (ETDEWEB)

    Charron, Richard C.; Little, David A.; Snyder, Gary D.

    2016-04-12

    An arrangement is provided for delivering gases from a plurality of combustors of a can-annular gas turbine combustion engine to a first row of turbine blades including a first row of turbine blades. The arrangement includes a gas path cylinder, a cone and an integrated exit piece (IEP) for each combustor. Each IEP comprises an inlet chamber for receiving a gas flow from a respective combustor, and includes a connection segment. The IEPs are connected together to define an annular chamber extending circumferentially and concentric to an engine longitudinal axis, for delivering the gas flow to the first row of blades. A radiused joint extends radially inward from a radially outer side of the inlet chamber to an outer boundary of the annular chamber, and a flared fillet extends radially inward from a radially inner side of the inlet chamber to an inner boundary of the annular chamber.

  10. Microwave plasma combustion of coal

    Energy Technology Data Exchange (ETDEWEB)

    P.M. Kanilo; V.I. Kazantsev; N.I. Rasyuk; K. Schuenemann; D.M. Vavriv [Institute of Machine Building Problems of the National Academy of Sciences of Ukraine, Kharkov (Ukraine)

    2003-01-01

    Microwave plasma is studied as an alternative to oil or gas fuel for ignition and stabilisation of burning of lean coal. The study is performed on an experimental set-up, which includes a burner with a microwave plasma generator, coal and air supply systems, and measurement equipment. Power and thermochemical characteristics of the coal-plasma interaction have been measured and analysed. The obtained results indicate an essential intensification of ignition and combustion processes in the microwave burner compared to those in conventional burners. In particular, it has been demonstrated that the microwave energy consumption is only about 10% of the required expenditure of oil or gas, measured in heat equivalent. A design of an industrial microwave-plasma burner is proposed. Prospects of such burner for applications at industrial boilers of power plants are discussed. 6 refs., 4 figs., 2 tabs.

  11. Combustion chemistry of solid propellants

    Science.gov (United States)

    Baer, A. D.; Ryan, N. W.

    1974-01-01

    Several studies are described of the chemistry of solid propellant combustion which employed a fast-scanning optical spectrometer. Expanded abstracts are presented for four of the studies which were previously reported. One study of the ignition of composite propellants yielded data which suggested early ammonium perchlorate decomposition and reaction. The results of a study of the spatial distribution of molecular species in flames from uncatalyzed and copper or lead catalyzed double-based propellants support previously published conclusions concerning the site of action of these metal catalysts. A study of the ammonium-perchlorate-polymeric-fuel-binder reaction in thin films, made by use of infrared absorption spectrometry, yielded a characterization of a rapid condensed-phase reaction which is likely important during the ignition transient and the burning process.

  12. Effect of Variant End of Injection Period on Combustion Process of Biodiesel Combustion

    Directory of Open Access Journals (Sweden)

    Khalid Amir

    2016-01-01

    Full Text Available Biodiesel is an alternative fuel as a replacement to the standard diesel fuel in combustion diesel engine. The biodiesel fuel has a significantly influences throughout the combustion process and exhaust emission. The purpose of this research is to investigate the combustion process behavior during the End of Injection (EOI period and operates under variant conditions using Rapid Compression Machine (RCM. Experimental of RCM is used to simulate a combustion process and combustion characteristics of diesel engine combustion. Three types of biodiesel blend which are B5, B10 and B15 were tested at several injection pressures of 80 MPa, 90 MPa and 130 MPa under different ambient temperatures, 750 K to 1100 K. The results of this study showed that the ignition delay slightly reduced with increasing the content of biodiesel blends from B5, B10 and B15 and became more shorten as the injection pressure been enhanced. As the injection pressure increased, the behavior of combustion pressure at end of injection is reduced, radically increased the NOX emission. It is noted that the process of combustion at the end of injection increased as the ambient temperature is rising. In fact, higher initial ambient temperature improved the fuel atomization and mixing process. Under the biodiesel combustion with higher ambient temperature condition, the exhaust emission of CO, O2, and HC became less but increased in NOX emission. Besides, increased in blends of biodiesel ratio are found to enhance the combustion process, resulted a decreased in HC emissions.

  13. Evaluation of self-combustion risk in tire derived aggregate fills.

    Science.gov (United States)

    Arroyo, Marcos; San Martin, Ignacio; Olivella, Sebastian; Saaltink, Maarten W

    2011-01-01

    Lightweight tire derived aggregate (TDA) fills are a proven recycling outlet for waste tires, requiring relatively low cost waste processing and being competitively priced against other lightweight fill alternatives. However its value has been marred as several TDA fills have self-combusted during the early applications of this technique. An empirical review of these cases led to prescriptive guidelines from the ASTM aimed at avoiding this problem. This approach has been successful in avoiding further incidents of self-combustion. However, at present there remains no rational method available to quantify self-combustion risk in TDA fills. This means that it is not clear which aspects of the ASTM guidelines are essential and which are accessory. This hinders the practical use of TDA fills despite their inherent advantages as lightweight fill. Here a quantitative approach to self-combustion risk evaluation is developed and illustrated with a parametric analysis of an embankment case. This is later particularized to model a reported field self-combustion case. The approach is based on the available experimental observations and incorporates well-tested methodological (ISO corrosion evaluation) and theoretical tools (finite element analysis of coupled heat and mass flow). The results obtained offer clear insights into the critical aspects of the problem, allowing already some meaningful recommendations for guideline revision. Copyright © 2011 Elsevier Ltd. All rights reserved.

  14. NO sub x reduction measures in coal combustion. NO sub x -mindernde Massnahmen bei der Kohleverbrennung

    Energy Technology Data Exchange (ETDEWEB)

    Hoelter, H.; Reichert, W.

    1987-03-26

    It is a well-known practice to design the coal dust burners in the combustion of coal in such a way that, by the guidance of the combustion air, they produce less NO{sub x} than usual. It is also a well-known practice to reduce the amount of NO{sub x} in the flue gases of fossil combustion plants by means of catalysts. According to the invention, the knowledge has now been gained that in the case of certain types of coal, preferably coal with a high content of volatile components, preheating of the coal substantially contributes to a reduction of the amount of NO{sub x} in the combustion. The preheating can lead up to the range of low temperature carbonization gas. In the case of fluidized bed firing systems, the coal is fed above the fluidized bed and, in the case of jet firing systems, the feeding of the preheated coal into the combustion chamber takes place by means of the nozzles. (orig.).

  15. Particulate matter emissions, and metals and toxic elements in airborne particulates emitted from biomass combustion: The importance of biomass type and combustion conditions.

    Science.gov (United States)

    Zosima, Angela T; Tsakanika, Lamprini-Areti V; Ochsenkühn-Petropoulou, Maria Th

    2017-05-12

    The aim of this study was to investigate the impact of biomass combustion with respect to burning conditions and fuel types on particulate matter emissions (PM10) and their metals as well as toxic elements content. For this purpose, different lab scale burning conditions were tested (20 and 13% O2 in the exhaust gas which simulate an incomplete and complete combustion respectively). Furthermore, two pellet stoves (8.5 and 10 kW) and one open fireplace were also tested. In all cases, 8 fuel types of biomass produced in Greece were used. Average PM10 emissions ranged at laboratory-scale combustions from about 65 to 170 mg/m(3) with flow oxygen at 13% in the exhaust gas and from 85 to 220 mg/m(3) at 20% O2. At pellet stoves the emissions were found lower (35 -85 mg/m(3)) than the open fireplace (105-195 mg/m(3)). The maximum permitted particle emission limit is 150 mg/m(3). Metals on the PM10 filters were determined by several spectrometric techniques after appropriate digestion or acid leaching of the filters, and the results obtained by these two methods were compared. The concentration of PM10 as well as the total concentration of the metals on the filters after the digestion procedure appeared higher at laboratory-scale combustions with flow oxygen at 20% in the exhaust gas and even higher at fireplace in comparison to laboratory-scale combustions with 13% O2 and pellet stoves. Modern combustion appliances and appropriate types of biomass emit lower PM10 emissions and lower concentration of metals than the traditional devices where incomplete combustion conditions are observed. Finally, a comparison with other studies was conducted resulting in similar results.

  16. Controlling the excess heat from oxy-combustion of coal by blending with biomass

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H.; Turan, A.Z.; Yaman, S.; Kucukbayrak, S. [Istanbul Technical University, Chemical and Metallurgical Engineering Faculty, Chemical Engineering Department, 34469, Maslak, Istanbul (Turkey)

    2010-11-15

    Two different biomass species such as sunflower seed shell and hazelnut shell were blended with Soma-Denis lignite to determine the effects of co-combustion on the thermal reactivity and the burnout of the lignite sample. For this purpose, Thermogravimetric Analysis and Differential Scanning Calorimetry techniques were applied from ambient to 900 C with a heating rate of 40 C/min under dry air and pure oxygen conditions. It was found that the thermal reactivities of the biomass materials and the lignite are highly different from each other under each oxidizing medium. On the other hand, the presence of biomass in the burning medium led to important influences not only on the burnout levels but also on the heat flows. The heat flow from the burning of lignite increased fivefold when the oxidizing medium was altered from dry air to pure oxygen. But, in case of co-combustion under oxygen, the excess heat arising from combustion of lignite could be reduced and this may be helpful to control the temperature of the combustion chamber. Based on this, co-combustion of coal/biomass blends under oxygen may be suggested as an alternative method to the ''Carbon Dioxide Recycle Method'' encountered in the oxyfuel combustion systems. (author)

  17. Extended lattice Boltzmann scheme for droplet combustion

    Science.gov (United States)

    Ashna, Mostafa; Rahimian, Mohammad Hassan; Fakhari, Abbas

    2017-05-01

    The available lattice Boltzmann (LB) models for combustion or phase change are focused on either single-phase flow combustion or two-phase flow with evaporation assuming a constant density for both liquid and gas phases. To pave the way towards simulation of spray combustion, we propose a two-phase LB method for modeling combustion of liquid fuel droplets. We develop an LB scheme to model phase change and combustion by taking into account the density variation in the gas phase and accounting for the chemical reaction based on the Cahn-Hilliard free-energy approach. Evaporation of liquid fuel is modeled by adding a source term, which is due to the divergence of the velocity field being nontrivial, in the continuity equation. The low-Mach-number approximation in the governing Navier-Stokes and energy equations is used to incorporate source terms due to heat release from chemical reactions, density variation, and nonluminous radiative heat loss. Additionally, the conservation equation for chemical species is formulated by including a source term due to chemical reaction. To validate the model, we consider the combustion of n-heptane and n -butanol droplets in stagnant air using overall single-step reactions. The diameter history and flame standoff ratio obtained from the proposed LB method are found to be in good agreement with available numerical and experimental data. The present LB scheme is believed to be a promising approach for modeling spray combustion.

  18. Extended lattice Boltzmann scheme for droplet combustion.

    Science.gov (United States)

    Ashna, Mostafa; Rahimian, Mohammad Hassan; Fakhari, Abbas

    2017-05-01

    The available lattice Boltzmann (LB) models for combustion or phase change are focused on either single-phase flow combustion or two-phase flow with evaporation assuming a constant density for both liquid and gas phases. To pave the way towards simulation of spray combustion, we propose a two-phase LB method for modeling combustion of liquid fuel droplets. We develop an LB scheme to model phase change and combustion by taking into account the density variation in the gas phase and accounting for the chemical reaction based on the Cahn-Hilliard free-energy approach. Evaporation of liquid fuel is modeled by adding a source term, which is due to the divergence of the velocity field being nontrivial, in the continuity equation. The low-Mach-number approximation in the governing Navier-Stokes and energy equations is used to incorporate source terms due to heat release from chemical reactions, density variation, and nonluminous radiative heat loss. Additionally, the conservation equation for chemical species is formulated by including a source term due to chemical reaction. To validate the model, we consider the combustion of n-heptane and n-butanol droplets in stagnant air using overall single-step reactions. The diameter history and flame standoff ratio obtained from the proposed LB method are found to be in good agreement with available numerical and experimental data. The present LB scheme is believed to be a promising approach for modeling spray combustion.

  19. LES/FMDF of High Speed Spray Combustion

    Science.gov (United States)

    Irannejad, Abolfazl; Jaberi, Farhad

    2013-11-01

    High speed evaporating and combusting sprays are computed with the hybrid two-phase large eddy simulation (LES)/filtered mass density function (FMDF) methodology. In this methodology, the resolved fluid velocity is obtained by solving the filtered form of the compressible Navier-Stokes equations with high-order finite difference schemes. The scalar (temperature and species mass fractions) field is obtained by solving the FMDF transport equation with a Lagrangian stochastic method. The spray is simulated with the Lagrangian droplets together with stochastic breakup and finite rate heat and mass transfer models. The liquid volume fraction is included in the LES/FMDF for denser spray regions. Simulations of high speed evaporating sprays with and without combustion for a range of gas and spray conditions indicate that the two-phase LES/FMDF results are consistent and compare well with the experimental results for global spray variables such as the spray penetration and flame lift-off lengths. The gas velocity and turbulence generated by the spray are found to be very significant in all simulated cases. A broad spectrum of droplet sizes is also found to be generated by the complex and coupled effects of the gas flow turbulence, droplet breakup, evaporation and combustion.

  20. Kinetics of plasma-assisted combustion: effect of non-equilibrium excitation on the ignition and oxidation of combustible mixtures

    Science.gov (United States)

    Popov, N. A.

    2016-08-01

    A review of experimental and theoretical investigations of the effect of atomic particles, and electronically and vibrationally excited molecules on the induction delay time and on the shift in the ignition temperature threshold of combustible mixtures is presented. The addition of oxygen and hydrogen atoms to combustible mixtures may cause a significant reduction in the ignition delay time. However, at relatively low initial temperatures, the non-equilibrium effect of the addition of atomic particles in ground electronic states is not pronounced. At the same time, the effect of excited O(1D) atoms on the oxidation and reforming of combustible mixtures is quite significant due to the high rates of reactions of O(1D) atoms with hydrogen and hydrocarbon molecules. In fuel-air mixtures, collisions with O(1D) atoms determine, under certain conditions, the dissociation of hydrocarbon molecules. Singlet oxygen molecules, O2(a1Δ g ), participate both in chain initiation and chain branching reactions, but the effect of O2(a1Δ g ) on the ignition processes is generally less important compared to oxygen atoms. The reactions of vibrationally excited molecules and the processes of VT-relaxation in combustible mixtures are discussed. The production of vibrationally excited N 2(v) molecules in fuel-air mixtures at relatively low electric field is very important. However, at the moment, the effect of the reactions of N 2(v) molecules on the oxidation and ignition of combustible mixtures is not completely clear, and requires further investigation. Therefore, with present knowledge, to reduce the ignition delay time and decrease the temperature threshold of combustive mixtures, the use of gas discharge systems with relatively high E/N values is recommended. In this case the reactions of electronically excited {{\\text{N}}2}≤ft(\\text{A}{}3Σu+,\\text{B}{}3{{\\Pi}g},\\text{C}{}3{{\\Pi}u},\\text{a}{}\\prime 1Σu-\\right) molecules, and atomic particles in ground and

  1. Catalytic combustion in small wood burning appliances

    Energy Technology Data Exchange (ETDEWEB)

    Oravainen, H. [VTT Energy, Jyvaeskylae (Finland)

    1996-12-31

    There is over a million hand fired small heating appliances in Finland where about 5,4 million cubic meters of wood fuel is used. Combustion in such heating appliances is a batch-type process. In early stages of combustion when volatiles are burned, the formation of carbon monoxide (CO) and other combustible gases are difficult to avoid when using fuels that have high volatile matter content. Harmful emissions are formed mostly after each fuel adding but also during char burnout period. When the CO-content in flue gases is, say over 0.5 %, also other harmful emissions will be formed. Methane (CH{sub 4}) and other hydrocarbons are released and the amount of polycyclic aromatic hydrocarbons (PAH)-compounds can be remarkable. Some PAH-compounds are very carcinogenic. It has been estimated that in Finland even more than 90 % of hydrocarbon and PAH emissions are due to small scale wood combustion. Emissions from transportation is excluded from these figures. That is why wood combustion has a net effect on greenhouse gas phenomena. For example carbon monoxide emissions from small scale wood combustion are two fold compared to that of energy production in power plants. Methane emission is of the same order as emission from transportation and seven fold compared with those of energy production. Emissions from small heating appliances can be reduced by developing the combustion techniques, but also by using other means, for example catalytic converters. In certain stages of the batch combustion, temperature is not high enough, gas mixing is not good enough and residence time is too short for complete combustion. When placed to a suitable place inside a heating appliance, a catalytic converter can oxidize unburned gases in the flue gas into compounds that are not harmful to the environment. (3 refs.)

  2. Thermally induced structural changes in coal combustion

    Energy Technology Data Exchange (ETDEWEB)

    Gavalas, G.R.; Flagan, R.C.

    1990-01-17

    The effect of particle shape on char burnout is investigated in the limit of shrinking core combustion. As a first step, the particle temperature is assumed to proceed in the shrinking core regime and under conditions of negligible Stefan flow. The problem then reduces to calculating the oxygen concentration field around a non-spherical particle with the oxidation reaction taking place on the external surface. This problem has been addressed by an analytical technique and a numerical technique. An analytical technique known as domain perturbation'' was used to examine the change due to reaction in the shape of a slightly nonspherical, but axisymmetric, particle. It was found that the aspect ratio always increases with conversion, i.e., the particle becomes less spherical. A numerical technique, based on the boundary integral'' method was developed to handle the case of an axisymmetric particle with otherwise arbitrary shape. Numerical results are presented which again show the aspect ratio to increase with conversion. 8 refs.

  3. Gasdynamic Model of Turbulent Combustion in TNT Explosions

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, A L; Bell, J B; Beckner, V E

    2010-01-08

    A model is proposed to simulate turbulent combustion in confined TNT explosions. It is based on: (i) the multi-component gasdynamic conservation laws, (ii) a fast-chemistry model for TNT-air combustion, (iii) a thermodynamic model for frozen reactants and equilibrium products, (iv) a high-order Godunov scheme providing a non-diffusive solution of the governing equations, and (v) an ILES approach whereby adaptive mesh refinement is used to capture the energy bearing scales of the turbulence on the grid. Three-dimensional numerical simulations of explosion fields from 1.5-g PETN/TNT charges were performed. Explosions in six different chambers were studied: three calorimeters (volumes of 6.6-l, 21.2-l and 40.5-l with L/D = 1), and three tunnels (L/D = 3.8, 4.65 and 12.5 with volumes of 6.3-l) - to investigate the influence of chamber volume and geometry on the combustion process. Predicted pressures histories were quite similar to measured pressure histories for all cases studied. Experimentally, mass fraction of products, Y{sub p}{sup exp}, reached a peak value of 88% at an excess air ratio of twice stoichiometric, and then decayed with increasing air dilution; mass fractions Y{sub p}{sup calc} computed from the numerical simulations followed similar trends. Based on this agreement, we conclude that the dominant effect that controls the rate of TNT combustion with air is the turbulent mixing rate; the ILES approach along with the fast-chemistry model used here adequately captures this effect.

  4. A multipurpose reduced chemical-kinetic mechanism for methanol combustion

    Science.gov (United States)

    Fernández-Tarrazo, Eduardo; Sánchez-Sanz, Mario; Sánchez, Antonio L.; Williams, Forman A.

    2016-07-01

    A multipurpose reduced chemical-kinetic mechanism for methanol combustion comprising 8 overall reactions and 11 reacting chemical species is presented. The development starts by investigating the minimum set of elementary reactions needed to describe methanol combustion with reasonable accuracy over a range of conditions of temperature, pressure, and composition of interest in combustion. Starting from a 27-step mechanism that has been previously tested and found to give accurate predictions of ignition processes for these conditions, it is determined that the addition of 11 elementary reactions taken from its basis (San Diego) mechanism extends the validity of the description to premixed-flame propagation, strain-induced extinction of non-premixed flames, and equilibrium composition and temperatures, giving results that compare favourably with experimental measurements and also with computations using the 247-step detailed San Diego mechanism involving 50 reactive species. Specifically, premixed-flame propagation velocities and extinction strain rates for non-premixed counterflow flames calculated with the 38-step mechanism show departures from experimental measurements and detailed-chemistry computations that are roughly on the order of 10%, comparable with expected experimental uncertainties. Similar accuracy is found in comparisons of autoignition times over the range considered, except at very high temperatures, under which conditions the computations tend to overpredict induction times for all of the chemistry descriptions tested. From this 38-step mechanism, the simplification is continued by introducing steady-state approximations for the intermediate species CH3, CH4, HCO, CH3O, CH2OH, and O, leading to an 8-step reduced mechanism that provides satisfactory accuracy for all conditions tested. The flame computations indicate that thermal diffusion has a negligible influence on methanol combustion in all cases considered and that a mixture-average species

  5. Sulphur poisoning and regeneration of precious metal catalysed methane combustion

    Energy Technology Data Exchange (ETDEWEB)

    Jones, J.M.; Dupont, V.A.; Fullerton, D.J.; Ross, A.B.; Westwood, A.V.K. [Department of Fuel and Energy, SPEME, University of Leeds, Leeds LS2 9JT (United Kingdom); Brydson, R. [Department of Materials, SPEME, University of Leeds, Leeds LS2 9JT (United Kingdom); Nasri, N.S. [Gas Engineering Department, Universiti Teknologi Malaysia, 81310 Skudai Johor (Malaysia)

    2003-07-01

    In many of the applications of catalytic combustion small amounts of sulphur compounds are present in the feed gas. In the case of natural gas combustion, and solid fuel syngas, the sulphur compounds are in reduced forms. The present work investigates the influence of small quantities of reduced sulphur compounds on the combustion of methane over alumina-supported precious metal catalysts. The kinetics of the methane combustion in the presence of low concentrations of a mixture of sulphur compounds (ethyl mercaptan, methyl mercaptan, carbonyl sulphide and hydrogen sulphide) are compared with those in the absence of sulphur compounds. The ease of regeneration of the poisoned catalysts, via low temperature reduction with hydrogen, is also examined. In the conditions studied all catalysts have reduced activity in the presence of the sulphur-based gas mixture, but Pt/Al{sub 2}O{sub 3} and Rh/Al{sub 2}O{sub 3} are more strongly poisoned than Pd/Al{sub 2}O{sub 3}. Qualitative studies using gas chromatography with atomic emission detection of the exhaust gases, and FTIR spectroscopy of the spent Rh/Al{sub 2}O{sub 3} catalyst, suggest that the catalysts experience a mixture of reduced and oxidised species under reaction conditions, and that sulphating of the support occurs. The regeneration step facilitates metal mobility and meets with varying success depending upon the metal. Pt/Al{sub 2}O{sub 3} in particular is difficult to regenerate by reduction in hydrogen (400C for 0.5h), and agglomeration is observed by TEM. Rh/Al{sub 2}O{sub 3} regenerates well, and low metal particle size is maintained. A non-linear deactivation model is tested to separate sulphur-induced deactivation from 'natural' deactivation in the reaction mixture and preliminary results are presented.

  6. Cleaner combustion developing detailed chemical kinetic models

    CERN Document Server

    Battin-Leclerc, Frédérique; Blurock, Edward

    2013-01-01

    This overview compiles the on-going research in Europe to enlarge and deepen the understanding of the reaction mechanisms and pathways associated with the combustion of an increased range of fuels. Focus is given to the formation of a large number of hazardous minor pollutants and the inability of current combustion models to predict the  formation of minor products such as alkenes, dienes, aromatics, aldehydes and soot nano-particles which have a deleterious impact on both the environment and on human health. Cleaner Combustion describes, at a fundamental level, the reactive chemistry of min

  7. Annual Report: Advanced Combustion (30 September 2012)

    Energy Technology Data Exchange (ETDEWEB)

    Hawk, Jeffrey [NETL; Richards, George

    2012-09-30

    The Advanced Combustion Project addresses fundamental issues of fire-side and steam-side corrosion and materials performance in oxy-fuel combustion environments and provides an integrated approach into understanding the environmental and mechanical behavior such that environmental degradation can be ameliorated and long-term microstructural stability, and thus, mechanical performance can lead to longer lasting components and extended power plant life. The technical tasks of this effort are Oxy-combustion Environment Characterization, Alloy Modeling and Life Prediction, and Alloy Manufacturing and Process Development.

  8. 3rd International Conference on Numerical Combustion

    CERN Document Server

    Larrouturou, Bernard; Numerical Combustion

    1989-01-01

    Interest in numerical combustion is growing among applied mathematicians, physicists, chemists, engine manufacturers and many industrialists. This proceedings volume contains nine invited lectures and twenty seven contributions carefully selected by the editors. The major themes are numerical simulation of transsonic and supersonic combustion phenomena, the study of supersonic reacting mixing layers, and turbulent combustion. Emphasis is laid on hyperbolic models and on numerical simulations of hydrocarbon planes with a complete set of chemical reactions carried out in two-dimensional geometries as well as on complex reactive flow simulations.

  9. Relationship Between Coal Powder and Its Combustibility

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Coal's volatile component,ash and fixed carbon content have different functions in different stages of a combustion process, but the traditional coal classification can precisely show its combustion property.In this experiment coal's evaluation indexes (ignition index Di),(burn off index Df) were used to qualitatively show the ignition property and combustion ending property of coal samples.Meanwhile,considering actual heating circumstances in calciner (in cement plants),this thesis established the relationship among the ignition index,burn off index and coal's industrial analysis value, which makes it possible for the user to predict the quality of coal before using it and is very valuable in practice.

  10. The John Zink Hamworthy combustion handbook

    CERN Document Server

    Baukal, Charles E

    2013-01-01

    Despite the length of time it has been around, its importance, and vast amounts of research, combustion is still far from being completely understood. Issues regarding the environment, cost, and fuel consumption add further complexity, particularly in the process and power generation industries. Dedicated to advancing the art and science of industrial combustion, The John Zink Hamworthy Combustion Handbook, Second Edition: Volume 3 - Applications offers comprehensive, up-to-date coverage of equipment used in the process and power generation industries. Under the leadership of Charles E. Baukal

  11. Study of cartridge rupture detection installations; Contribution a l'etude des installations de detection de ruptures de gaine

    Energy Technology Data Exchange (ETDEWEB)

    Graftieaux, J.; Douet, P.; Roguin, A. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-07-01

    Very numerous physical or technological parameters are involved in the preparation of projects for can rupture detection installations. These parameters are connected essentially with the design of the reactor, the detector used, the disposition of the pneumatic circuits, the type of fuel and the safety required. The present report analyses the main problems arising and their mutual compatibilities; it defines a certain number of ideas which had up till now been accepted implicitly in the design. (authors) [French] De tres nombreux parametres physiques ou technologiques interviennent dans l'etablissement du projet d'une installation de detection de ruptures de gaines. Ces parametres decoulent essentiellement de la conception de la pile, du detecteur utilise, de l'organisation des circuits pneumatiques, du type du combustible et de la securite souhaitee. Le present document analyse les principaux problemes qui se posent ainsi que leurs compatibilites reciproques et precise un certain nombre de notions jusqu'alors admises implicitement lors de l'etablissement des projets. (auteurs)

  12. Key factors of combustion from kinetics to gas dynamics

    CERN Document Server

    Rubtsov, Nikolai M

    2017-01-01

    This book summarizes the main advances in the mechanisms of combustion processes. It focuses on the analysis of kinetic mechanisms of gas combustion processes and experimental investigation into the interrelation of kinetics and gas dynamics in gas combustion. The book is complimentary to the one previously published, The Modes of Gaseous Combustion.

  13. Pulse combustion: an assessment of opportunities for increased efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Brenchley, D.L.; Bomelburg, H.J.

    1984-12-01

    The results of a literature review on pulse combustion are discussed. Current, near-future, and potential opportunities for pulse combustion applications are summarized, and the barriers to developing and using pulse combustion technology are discussed, along with research and development needs. Also provided are the proceedings of a pulse combustion workshop held in May, 1984 in Seattle, Washington. (LEW)

  14. Coal Combustion Science quarterly progress report, April--June 1990

    Energy Technology Data Exchange (ETDEWEB)

    Hardesty, D.R. (ed.); Baxter, L.L.; Fletcher, T.H.; Mitchell, R.E.

    1990-11-01

    This document provides a quarterly status report of the Coal Combustion Science Program that is being conducted at the Combustion, Research Facility, Sandia National Laboratories, Livermore, California. Coal devolatilization, coal char combustion, and fate of mineral matter during coal combustion. 56 refs., 25 figs., 13 tabs.

  15. Theoretical Analysis and Derivation of Combustion Wave Parameters

    Institute of Scientific and Technical Information of China (English)

    CHEN Jun

    2006-01-01

    Theoretical relations of pressure, density, velocity, temperature and Mach number of combustion waves are built. The parameters' curves with different combustion energy are illustrated in which four zones are pointed out to represent different combustion states. The expressions and curves of parameters are important to analyze the trends of combustion waves, and to determine conditions on which detonation waves or deflagration waves occur.

  16. A numerical study of turbulent combustion characteristics in a combustion chamber of a scramjet engine

    Institute of Scientific and Technical Information of China (English)

    LEE; ChunHian

    2010-01-01

    3D numerical simulation of flow fields in a combustion chamber of a scramjet engine using an SST turbulence model with an explicit compressibility correction was performed and the results were compared to the experimental results.The characteristics of the turbulent combustion flow fields were analyzed via the numerical results and presented.In order to identify the mechanisms of turbulent combustion in supersonic flows,the evolutions of governing dimensionless parameters in the flow fields were investigated based on the theory of combustion and the available numerical results.It was found that the supersonic combustion takes place in the region of fully developed turbulence and that the strongest effects of turbulence and combustion processes appear in the vicinity of the injector.The unsteady effects and the local flame extinction phenomenon induced by turbulent flows were found to be negligibly small,and the steady flamelet approximation will hold for practical applications.

  17. Combustion instability detection using the wavelet detail of pressure fluctuations

    Institute of Scientific and Technical Information of China (English)

    Junjie JI; Yonghao LUO

    2008-01-01

    A combustion instability detection method that uses the wavelet detail of combustion pressure fluctuations is put forward. To confirm this method, combustion pressure fluctuations in a stoker boiler are recorded at stable and unstable combustion with a pressure transducer. Daubechies one-order wavelet is chosen to obtain the wavelet details for comparison. It shows that the wavelet approximation indicates the general pressure change in the furnace, and the wavelet detail magnitude is consistent with the intensity of turbulence and combustion noise. The magnitude of the wavelet detail is nearly constant when the combustion is stable, however, it will fluctuate much when the combustion is unstable.

  18. Survey of Greener Ignition and Combustion Systems for Internal Combustion Engines

    OpenAIRE

    Luo, Wuqiao; Li, Yun; Tian, Zhong; Gao, Bo; Tong, Ling; Wang, Houjun; Zeng, Baoqing

    2015-01-01

    The spark and compression ignition principles of, petrol and diesel internal combustion engines (ICEs) have, not advanced for a century. These do not lead to complete, combustion and hence result in high exhaust emission and, low energy efficiency. This paper presents a comprehensive survey on the attempts and developments of greener ignition, and combustion systems for ICEs and points out that, homogeneous charge microwave ignition (HCMI) holds the, key to a perfect solution. Increasing the ...

  19. Operation Evaluation Method for Marine Turbine Combustion Engines in Terms of Energetics

    Directory of Open Access Journals (Sweden)

    Dzida Marek

    2016-12-01

    Full Text Available An evaluation proposal (quantitative determination of any combustion turbine engine operation has been presented, wherein the impact energy occurs at a given time due to Energy conversion. The fact has been taken into account that in this type of internal combustion engines the energy conversion occurs first in the combustion chambers and in the spaces between the blade of the turbine engine. It was assumed that in the combustion chambers occurs a conversion of chemical energy contained in the fuel-air mixture to the internal energy of the produced exhaust gases. This form of energy conversion has been called heat. It was also assumed that in the spaces between the blades of the rotor turbine, a replacement occurs of part of the internal energy of the exhaust gas, which is their thermal energy into kinetic energy conversion of its rotation. This form of energy conversion has been called the work. Operation of the combustion engine has been thus interpreted as a transmission of power receivers in a predetermined time when there the processing and transfer in the form (means of work and heat occurs. Valuing the operation of this type of internal combustion engines, proposed by the authors of this article, is to determine their operation using physical size, which has a numerical value and a unit of measurement called joule-second [joule x second]. Operation of the combustion turbine engine resulting in the performance of the turbine rotor work has been presented, taking into account the fact that the impeller shaft is connected to the receiver, which may be a generator (in the case of one-shaft engine or a propeller of the ship (in the case of two or three shaft engine.

  20. Progress on the Combustion Integrated Rack Component of the Fluids and Combustion Facility

    Science.gov (United States)

    Weiland, Karen J.; Urban, Dave (Technical Monitor)

    1999-01-01

    The Fluids and Combustion Facility (FCF) is a facility-class payload planned for the International Space Station. It is designed to accommodate a wide variety of investigations encompassing most of the range of microgravity fluid physics and combustion science. The Combustion Integrated Rack component of the FCF is currently scheduled to be launched in 2003 and will operate independently until additional racks of the FCF are launched. The FCF is intended to complete between five and fifteen combustion experiments per year over its planned ten-year lifetime. Combustion arm that may be studied include laminar flames, reaction kinetics, droplet and spray combustion, flame spread, fire and fire suppressants, condensed phase organic fuel combustion, turbulent combustion, soot and polycyclic aromatic hydrocarbons, and flame-synthesized materials. Three different chamber inserts, one each for investigations of droplet, solid fuel, and gaseous fuel combustion, that can accommodate multiple experiments will be used initially so as to maximize the reuse of hardware. The current flight and flight-definition investigations are briefly described.