Generalized collar waves in acoustic logging while drilling

International Nuclear Information System (INIS)

Wang Xiu-Ming; He Xiao; Zhang Xiu-Mei

2016-01-01

Tool waves, also named collar waves, propagating along the drill collars in acoustic logging while drilling (ALWD), strongly interfere with the needed P- and S-waves of a penetrated formation, which is a key issue in picking up formation P- and S-wave velocities. Previous studies on physical insulation for the collar waves designed on the collar between the source and the receiver sections did not bring to a satisfactory solution. In this paper, we investigate the propagation features of collar waves in different models. It is confirmed that there exists an indirect collar wave in the synthetic full waves due to the coupling between the drill collar and the borehole, even there is a perfect isolator between the source and the receiver. The direct collar waves propagating all along the tool and the indirect ones produced by echoes from the borehole wall are summarized as the generalized collar waves. Further analyses show that the indirect collar waves could be relatively strong in the full wave data. This is why the collar waves cannot be eliminated with satisfactory effect in many cases by designing the physical isolators carved on the tool. (special topic)

Wolves, Canis lupus, carry and cache the collars of radio-collared White-tailed Deer, Odocoileus virginianus, they killed

Science.gov (United States)

Nelson, Michael E.; Mech, L. David

2011-01-01

Wolves (Canis lupus) in northeastern Minnesota cached six radio-collars (four in winter, two in spring-summer) of 202 radio-collared White-tailed Deer (Odocoileus virginianus) they killed or consumed from 1975 to 2010. A Wolf bedded on top of one collar cached in snow. We found one collar each at a Wolf den and Wolf rendezvous site, 2.5 km and 0.5 km respectively, from each deer's previous locations.

Collar of Lady's Wear in Qing Dynasty

Institute of Scientific and Technical Information of China (English)

LI Xiao-jun

2007-01-01

The research is started with a query that whether the width of collar in Qing Dynasty Is too small. The paper bases on the statistics which come from the collection of the Costume Museum of Donghua University. compares the results with the natlonal standard specification, then analyzes the structure and shape of collars in Qing Dynasty, and tells the relationship between collar and the garment. Furthermore, the paper discusses the function of lady's collar in Qing Dynasty and gives a suggestion that collar being an Indicator to distinguish women's wear from children's wear.

Expert System for 3D Collar Intelligent Design

Institute of Scientific and Technical Information of China (English)

LIU Yan; GENG Zhao-feng

2004-01-01

A method to set up 3D collar prototype is developed in this paper by using the technique of cubic spline and bicubic surface patch. Then the relationship between the parameters of 3D collar prototype and different collar styles are studied. Based on the relationship, we can develop some algorithms of transferring style requirements to the parameters value of the collar prototype, and obtain some generation rules for the design of 3D collar style. As such, the knowledge base can be constructed, and the intelligent design system of 3D collar style is built. Using the system, various 3D collar styles can be designed automatically to satisfy various style requirements.

Electropolishing or chemical milling of beryllium to remove machining defects

International Nuclear Information System (INIS)

Helms, J.R.

1975-12-01

The techniques of electropolishing and chemical milling to remove machine damage from beryllium are compared. Both techniques are found to be effective; chemical milling is recommended because it is easier to use and control

High Metal Removal Rate Process for Machining Difficult Materials

Energy Technology Data Exchange (ETDEWEB)

Bates, Robert; McConnell, Elizabeth

2016-06-29

Machining methods across many industries generally require multiple operations to machine and process advanced materials, features with micron precision, and complex shapes. The resulting multiple machining platforms can significantly affect manufacturing cycle time and the precision of the final parts, with a resultant increase in cost and energy consumption. Ultrafast lasers represent a transformative and disruptive technology that removes material with micron precision and in a single step manufacturing process. Such precision results from athermal ablation without modification or damage to the remaining material which is the key differentiator between ultrafast laser technologies and traditional laser technologies or mechanical processes. Athermal ablation without modification or damage to the material eliminates post-processing or multiple manufacturing steps. Combined with the appropriate technology to control the motion of the work piece, ultrafast lasers are excellent candidates to provide breakthrough machining capability for difficult-to-machine materials. At the project onset in early 2012, the project team recognized that substantial effort was necessary to improve the application of ultrafast laser and precise motion control technologies (for micromachining difficult-to-machine materials) to further the aggregate throughput and yield improvements over conventional machining methods. The project described in this report advanced these leading-edge technologies thru the development and verification of two platforms: a hybrid enhanced laser chassis and a multi-application testbed.

The effect of nozzle collar on signle phase and boiling heat transfer by planar impinging jet

International Nuclear Information System (INIS)

Shin, Chang Hwan; Yim, Seong Hwan; Cho, Hyung Hee; Wu, Seong Je

2005-01-01

The water jet impingement cooling is one of the techniques to remove the heat from high heat flux equipment. Local heat transfer of the confined water impinging jet and the effect of nozzle collar to enhance the heat transfer are investigated in the free surface jet and submerged jet. Boiling is initiated from the farthest downstream and increase of the wall temperature is reduced with developing boiling, forming the flat temperature distributions. The reduction in the nozzle-to-surface distance for H/W≤1 causes significant increases and distribution changes of heat transfer. Developed boiling reduces the differences of heat transfer for various conditions. The nozzle collar is employed at the nozzle exit. The distances from heated surface to nozzle collar, H c are 0.25W, 0.5W and 1.0W. The liquid film thickness is reduced and the velocity of wall jet increases as decreased spacing of collar to heated surface. Heat transfer is enhanced for region from the stagnation to x/W∼8 in the free surface jet and to x/W∼5 in the submerged jet. For nucleate boiling region of further downstream, the heat transfer by the nozzle collar is decreased in submerged jet comparing with higher velocity condition. It is because the increased velocity by collar is de-accelerated downstream

Proximal femoral anatomy and collared stems in hip arthroplasty: is a single collar size sufficient?

Science.gov (United States)

Bonin, Nicolas; Gedouin, Jean-Emmanuel; Pibarot, Vincent; Bejui-Hughues, Jacques; Bothorel, Hugo; Saffarini, Mo; Batailler, Cécile

2017-10-03

Even if the benefits of collars are unclear, they remain widely used, in several femoral stem designs. This study aimed to determine whether collar size should be proportional to hip dimensions and morphology. The hypothesis was that the collar should be larger for greater stem sizes and for varus femoral necks. Computed Tomography scans of 204 healthy hips were digitally analysed and manually templated to determine principle dimensions, appropriate stem size and model, as well as cortical distance at the femoral calcar (ideal collar size). Univariable analysis revealed that cortical distance was moderately correlated with mediolateral offset (r = 0.572; p < 0.0001) and stem model (r = 0.520; p < 0.0001). Cortical distance was weakly correlated with head diameter (r = 0.399; p < 0.0001), stem size (r = 0.200; p = 0.017), and patient gender (r = 0.361; p < 0.0001). Multivariable analysis confirmed that stem model (p < 0.0001) and head diameter (p = 0.0162) are directly correlated to cortical distance. We found that cortical distance along the femoral calcar is directly correlated with the model of the stem implanted ('standard' or 'varus') and with the head diameter. This cortical distance indicates optimal collar size, which would grant maximum calcar coverage without prosthetic overhang. Collar size should be proportional to the size of the operated hip, and should be larger for 'varus' stem models than for 'standard' stem models.

Development of a machine treating removed shells and others in thermal and nuclear power stations

International Nuclear Information System (INIS)

Daiho, Koichi; Iwao, Takenobu

1981-01-01

The living things removed form the cooling water systems in thermal and nuclear power stations, such as shells and jelly fish, have been disposed by burying in the premises, but it is the actual situation that the occurrence of bad smell and the securing of land for burying are the worries. Accordingly, a machine for deodorizing the removed living things was manufactured for trial, and the treatment experiment was carried out in Chita Power Station. This treating machine dries the removed living things around 200 deg C, and makes the deodorizing treatment. The treated products can be utilized effectively as fertilizer, and the prospect to put this machine in practical use as a waste treatment machine of resource re-utilization type was obtained. General Technical Research Institute, Chubu Electric Power Co., Inc., has developed a machine treating abandoned fish for making organic fertilizer, and its principle was applied to the development of this treating machine. The treating capacity of this machine is 1 t/day, and the power consumption is 9.3 kW. The waste oil from power stations of about 15 l/h is used as the fuel. A crusher, a constant feed screw conveyer and a rotary kiln for drying are used. In the treating experiment, about 30 t of shells and others were treated during 51 days. The results are reported. (Kako, I.)

Occupational contact dermatitis in blue-collar workers

DEFF Research Database (Denmark)

Schwensen, Jakob F; Menné, Torkil; Veien, Niels K

2014-01-01

BACKGROUND: Blue-collar workers have a high risk of occupational contact dermatitis, but epidemiological studies are scarce. OBJECTIVES: To investigate allergic contact dermatitis in blue-collar workers with dermatitis registered by the Danish Contact Dermatitis Group. METHODS: A retrospective...... analysis of patch test data from 1471 blue-collar workers and 1471 matched controls tested between 2003 and 2012 was performed. A logistic regression was used to test for associations. RESULTS: The blue-collar workers often had occupational hand dermatitis (p dermatitis was less commonly......, and methylchloroisothiazolinone (MCI)/methylisothiazolinone (MI). The following occupations were additionally identified as risk factors for contact sensitization to MCI/MI and MI, epoxy resins, and potassium dichromate, respectively: painting, construction work, and tile setting/terrazzo work. CONCLUSION: Contact allergy...

Organizational justice is related to heart rate variability in white-collar workers, but not in blue-collar workers-findings from a cross-sectional study.

Science.gov (United States)

Herr, Raphael M; Bosch, Jos A; van Vianen, Annelies E M; Jarczok, Marc N; Thayer, Julian F; Li, Jian; Schmidt, Burkhard; Fischer, Joachim E; Loerbroks, Adrian

2015-06-01

Perceived injustice at work predicts coronary heart disease. Vagal dysregulation represents a potential psychobiological pathway. We examined associations between organizational justice and heart rate variability (HRV) indicators. Grounded in social exchange and psychological contract theory, we tested predictions that these associations are more pronounced among white-collar than among blue-collar workers. Cross-sectional data from 222 blue-collar and 179 white-collar men were used. Interactional and procedural justice were measured by questionnaire. Ambulatory HRV was assessed across 24 h. Standardized regression coefficients (β) were calculated. Among white-collar workers, interactional justice showed positive relationships with 24-h HRV, which were strongest during sleeping time (adjusted βs≥0.26; p values≤0.01). No associations were found for blue-collar workers. A comparable but attenuated pattern was observed for procedural justice. Both dimensions of organizational injustice were associated with lowered HRV among white-collar workers. The impact of justice and possibly its association with health seems to differ by occupational groups.

Analysis of Material Removal and Surface Characteristics in Machining Multi Walled Carbon Nanotubes Filled Alumina Composites by WEDM Process

Directory of Open Access Journals (Sweden)

Annebushan Singh Meinam

2017-01-01

Full Text Available The reinforcement of ceramic materials with electrically conductive particles increases the overall conductivity of the ceramic material. This allows the ceramic material to be more readily machined using wire electrical discharge machining process. The current work is an approach to identify the machinability of multi walled carbon nanotubes filled alumina composites in wire electrical discharge machining process. Alumina samples of 5 vol. % and 10 vol. % multi walled carbon nanotubes are machined and analysed for material removal rate and the surface characteristics. An increase in material removal rate is observed with increase in filler concentrations. At the same time, better surface roughness is observed. The surface characteristics of composite alumina are further compared with Monel 400 alloy. It has been observed that spalling action is the dominating material removal mechanism for alumina composites, while melting and evaporation is for the Monel 400 alloy.

Use of cervical collar after whiplash injuries.

Science.gov (United States)

Józefiak-Wójtowicz, Anna; Stolarczyk, Artur; Deszczyński, Jarosław Michał; Materek, Magdalena; Pietras, Marta; Bażant, Katarzyna

2014-08-08

Whiplash injuries, also known as neck sprains and strains, are currently some of the most common injuries of the cervical spine. Mechanism of injury is still controversial and current treatment methods do not provide satisfactory results. In this article we present QTF classification of related disorders, epidemiological data and treatment methods. We described basic principles of using a soft collar, goals and effects of collar use and potential complications ensuing from immobilization. Authors reviewed publications comparing the effects of collar use with other methods of treatment and physiotherapy following whiplash injury.

Mechanical test results on Dipole model C-1 25 mm aluminum collars

International Nuclear Information System (INIS)

Peters, C.

1985-02-01

This report is a summary of procedures used in collaring the SSC Dipole model C-1. Included are descriptions of the collars, instrumentation, collar pack preparation, collaring procedures, and collar dimension and coil pressure data measurements taken during and testing of the magnet

Draining Collars and Lenses in Liquid-Lined Vertical Tubes.

Science.gov (United States)

Jensen

2000-01-01

The speed at which an annular liquid collar drains under gravity g in a vertical tube of radius a, when the tube has an otherwise thin viscous liquid lining on its interior, is determined by a balance between the collar's weight and viscous shear stresses confined to narrow regions in the neighborhood of the collar's effective contact lines. Whether a collar grows or shrinks in volume as it drains depends on the modified Bond number B=rho g a(2)/(sigmaepsilon), where rho is the fluid density, sigma is its surface tension, and epsilona is the thickness of the thin film immediately ahead of the collar. Asymptotic methods are used here to determine the following nonlinear stability criteria for an individual collar, valid in the limit of small epsilon. For 0draining collars grow in volume and, in sufficiently long tubes, ultimately "snap off" to form stable lenses. For 0.5960drain, so that any lens ultimately ruptures, unless stabilizing intermolecular forces allow the formation of a lamella supported by a macroscopic Plateau border. If surfactant immobilizes the liquid's free surface, these critical values of B are reduced by a factor of 2 but the distance a collar must travel before it snaps off is unchanged. Gravitationally driven snap off is therefore most likely to occur in long tubes with radii substantially less than the capillary lengthscale sigma/rhog)(1/2). Copyright 2000 Academic Press.

Birds be safe: Can a novel cat collar reduce avian mortality by domestic cats (Felis catus?

Directory of Open Access Journals (Sweden)

S.K. Willson

2015-01-01

Full Text Available The domestic cat (Felis catus has been described as the largest anthropogenic threat to songbird populations in North America. We examined the effectiveness of a novel cat collar in reducing avian and small mammal mortality by cats. The 2-inch wide Birdsbesafe® collar cover (CC is worn over a nylon quick-release collar, and the bright colors and patterns of the CC are hypothesized to warn birds of approaching cats. We conducted two seasonal trials, each lasting 12 weeks, in autumn 2013 (n=54 cats and spring 2014 (n=19 cats. Cats were randomly assigned to two groups, and CCs with interior collars were removed or put on every two weeks, to control for weather fluctuations and seasonal change. Cats wearing Birdsbesafe® CCs killed 19 times fewer birds than uncollared cats in the spring trial, and 3.4 times fewer birds in the fall. Birdsbesafe® CCs were extremely effective at reducing predation on birds. Small mammal data were less clear, but did decrease predation by half in the fall. The Birdsbesafe® CC is a highly effective device for decreasing bird predation, especially in the spring season. We suggest that the CCs be used as a conservation tool for owned as well as feral cats.

Reducing Local Scouring at Bridge Piles Using Collars and Geobags

Directory of Open Access Journals (Sweden)

Shatirah Akib

2014-01-01

Full Text Available The present study examines the use of collars and geobags for reducing local scour around bridge piles. The efficiency of collars and geobags was studied experimentally. The data from the experiments were compared with data from earlier studies on the use of single piles with a collar and with a geobag. The results showed that using a combination of a steel collar and a geobag yields the most significant scour reduction for the front and rear piles, respectively. Moreover, the independent steel collar showed better efficiency than the independent geobag below the sediment level around the bridge piles.

[Health impact assessment of "white-collar exemption" in Japan].

Science.gov (United States)

Fujino, Yoshihisa; Matsuda, Shinya

2007-03-01

This work conducted a health impact assessment (HIA) of the Japanese Government's proposal concerning the introduction of so called "white-collar exemption" into the Japanese labor market. We adopted the Merseyside model and performed a rapid health impact assessment to assess the potential health effects of white-collar exemption. In this HIA, several health determinants which may possibly be affected, both positively and negatively, were identified based on experts' judgments. Literature evidence was assessed using PubMed and other databases. In addition, we searched for the opinions of those affected by white-collar exemption from internet web sites, and six concerns were identified. Long working hours were identified as the most serious concern by both experts and those affected. White-collar exemption may increase irregular working patterns which may be related to sleep disorder, stress, and cardiovascular disease. Family function and social participation will also be affected by irregular working patterns. On the other hand, in terms of stress, white-collar exemption may benefit from a higher degree of job control. There are possibilities that white-collar exemption may enable an improved work-life balance and enable access of some groups of the population, such as people with disabilities or parents looking after children, greater access to the labour market. However, it is uncertain whether the benefits of white-collar exemption would overcome those of the current free-time or flex-time systems. The present work provides a wide range of health impacts of white-collar exemption, and will hopefully attract the attentions of decision-makers and those likely to be affected in order to contribute to policy-making.

Sickness benefit cuts mainly affect blue-collar workers.

Science.gov (United States)

Aaviksoo, E; Kiivet, R-A

2014-08-01

To analyse the impact of sick-pay cuts on the use of sickness absence by employees of different socioeconomic groups. In 2009 cuts in sick pay were implemented in reaction to an economic crisis in Estonia. Nationwide health survey data from the years 2004, 2006, 2008, and 2010 were used to evaluate sickness absence among blue-collar and white-collar workers. The dataset comprised 7,449 employees of 20-64 years of age. Difference in prevalence of absentees before and after the reform was assessed using the chi-squared test. Odds ratios (OR) for sickness absence were calculated in a multivariate logistic regression model. After the reform, the proportion of blue-collar workers who had been on sick leave decreased from 51% to 40% (pgender, age, self-rated health, and presence of chronic disease, especially among those with low incomes; in white-collar employees it reached statistical significance only in those with good self-rated health (p=0.033). In a multivariate model the odds of having lower sickness absence were highly significant only in blue-collar employees (OR 0.63; 95% confidence interval 0.51-0.77, p<0.001). The cuts in sickness benefits had a major impact on the use of sickness absence by blue-collar employees with low salaries. This indicates that lower income was a major factor hindering the use of sick leave as these employees are most vulnerable to the loss of income. © 2014 the Nordic Societies of Public Health.

Testing VHF/GPS collar design and safety in the study of free-roaming horses.

Directory of Open Access Journals (Sweden)

Gail H Collins

Full Text Available Effective and safe monitoring techniques are needed by U.S. land managers to understand free-roaming horse behavior and habitat use and to aid in making informed management decisions. Global positioning system (GPS and very high frequency (VHF radio collars can be used to provide high spatial and temporal resolution information for detecting free-roaming horse movement. GPS and VHF collars are a common tool used in wildlife management, but have rarely been used for free-roaming horse research and monitoring in the United States. The purpose of this study was to evaluate the design, safety, and detachment device on GPS/VHF collars used to collect free-roaming horse location and movement data. Between 2009 and 2010, 28 domestic and feral horses were marked with commercial and custom designed VHF/GPS collars. Individual horses were evaluated for damage caused by the collar placement, and following initial observations, collar design was modified to reduce the potential for injury. After collar modifications, which included the addition of collar length adjustments to both sides of the collar allowing for better alignment of collar and neck shapes, adding foam padding to the custom collars to replicate the commercial collar foam padding, and repositioning the detachment device to reduce wear along the jowl, we observed little to no evidence of collar wear on horses. Neither custom-built nor commercial collars caused injury to study horses, however, most of the custom-built collars failed to collect data. During the evaluation of collar detachment devices, we had an 89% success rate of collar devices detaching correctly. This study showed that free-roaming horses can be safely marked with GPS and/or VHF collars with minimal risk of injury, and that these collars can be a useful tool for monitoring horses without creating a risk to horse health and wellness.

A Collar for Marking Big Game Animals

Science.gov (United States)

Robert L. Phillips

1970-01-01

A Simple, inexpensive collar made of Armor-tite (a vinyl-coated nylon fabric) was designed for marking white-tailed deer (Odocoileus virginianus) and moose (Alces alces). Field tests showed that the material is easily seen and extrememly durable. It may be suitable for use on other large mammals. The collar can be quickly fitted to individual animals under field...

A beaded collar for dual micro GPS/VHF transmitter attachment to nutria

Science.gov (United States)

Haramis, G.M.; White, T.S.

2011-01-01

We report on the development of an approximately 85-g beaded collar for dual micro GPS/VHF transmitter attachment to semi-aquatic nutria (Myocastor coypus). Prototype collars were tested on captive nutria and refined during field trials. Central to the design was novel use of the VHF transmitter antenna as a collar. A circular collar was formed by passing the 44-cm antenna cable through a pre-made hole in the transmitter, leaving an approximately 16-cm upright antenna. GPS units were mounted separately via a hole in the base of each unit. For good satellite contact, GPS units (28 g) were maintained at the nape of the neck by counterbalance of the heavier VHF transmitters (50 g) positioned under the neck. To reduce friction, we lined the collar with alternate-sized plastic and, later, more durable nylon beads. The final collar configuration was worn for approximately 1 month deployments with only minor neck abrasion; one collar was worn successfully for 5 months. Foot entanglement remained the greatest risk of injury from the collar. By fitting collars tightly, we reduced the incidence of foot entanglement to 2 of 33 deployments (6%). Successful GPS tracks were acquired on 29 of 33 deployments (88%).

Increased Executive Functioning, Attention, and Cortical Thickness in White-Collar Criminals

Science.gov (United States)

Raine, Adrian; Laufer, William S.; Yang, Yaling; Narr, Katherine L.; Thompson, Paul; Toga, Arthur W.

2011-01-01

Very little is known on white collar crime and how it differs to other forms of offending. This study tests the hypothesis that white collar criminals have better executive functioning, enhanced information processing, and structural brain superiorities compared to offender controls. Using a case-control design, executive functioning, orienting, and cortical thickness was assessed in 21 white collar criminals matched with 21 controls on age, gender, ethnicity, and general level of criminal offending. White collar criminals had significantly better executive functioning, increased electrodermal orienting, increased arousal, and increased cortical gray matter thickness in the ventromedial prefrontal cortex, inferior frontal gyrus, somatosensory cortex, and the temporal-parietal junction compared to controls. Results, while initial, constitute the first findings on neurobiological characteristics of white-collar criminals It is hypothesized that white collar criminals have information-processing and brain superiorities that give them an advantage in perpetrating criminal offenses in occupational settings. PMID:22002326

Health beliefs of blue collar workers. Increasing self efficacy and removing barriers.

Science.gov (United States)

Wilson, S; Sisk, R J; Baldwin, K A

1997-05-01

The study compared the health beliefs of participants and non-participants in a blood pressure and cholesterol screening held at the worksite. A cross sectional, ex-post facto design was used. Questionnaires measuring health beliefs related to cardiac screening and prevention of cardiac problems were distributed to a convenience sample of 200 blue-collar workers in a large manufacturing plant in the Midwest. One hundred fifty-one (75.5%) completed questionnaires were returned, of which 45 had participated in cardiac worksite screening in the past month. A multivariate analysis of variance was used to analyze data. Participants perceived significantly fewer barriers to cardiac screening and scored significantly higher on self efficacy than non-participants. These findings concur with other studies identifying barriers and self efficacy as important predictors of health behavior. Occupational health nurses' efforts are warranted to reduce barriers and improve self efficacy by advertising screenings, scheduling them at convenient times and locations, assuring privacy, and keeping time inconvenience to a minimum.

Tribological characterization of the drill collars and casing friction couples

Science.gov (United States)

Ripeanu, R. G.; Badicioiu, M.; Caltaru, M.; Dinita, A.; Laudacescu, E.

2018-01-01

Drill collars are special pipes used in the drilling of wells for weighting the drill bit, enabling it to drill through the rock. In the drilling process, the drill collars are exposed to an intensive wear due to friction on inner surface of casing wall. In order to evaluate the tribological behaviour of this friction couple, paper presents the drill collars parent material, reconditioned and casing pipe chemical composition, microstructures, hardness and friction tests. For friction tests were prepared samples extracted from new and reconditioned drill collars and from casing pipes and tested on a universal tribometer. Were used plane-on-disk surface friction couples and tests were conducted at two sliding speeds and three normal loads for each materials couple. Plane static partner samples were extracted from casing pipes and disks samples were extracted from new and reconditioned drill collars. Were obtained friction coefficients values and also the temperatures increasing values due to friction working tests parameters. The temperature increasing values were obtained by measuring it with an infrared thermographic camera.

Machine vision system for measuring conifer seedling morphology

Science.gov (United States)

Rigney, Michael P.; Kranzler, Glenn A.

1995-01-01

A PC-based machine vision system providing rapid measurement of bare-root tree seedling morphological features has been designed. The system uses backlighting and a 2048-pixel line- scan camera to acquire images with transverse resolutions as high as 0.05 mm for precise measurement of stem diameter. Individual seedlings are manually loaded on a conveyor belt and inspected by the vision system in less than 0.25 seconds. Designed for quality control and morphological data acquisition by nursery personnel, the system provides a user-friendly, menu-driven graphical interface. The system automatically locates the seedling root collar and measures stem diameter, shoot height, sturdiness ratio, root mass length, projected shoot and root area, shoot-root area ratio, and percent fine roots. Sample statistics are computed for each measured feature. Measurements for each seedling may be stored for later analysis. Feature measurements may be compared with multi-class quality criteria to determine sample quality or to perform multi-class sorting. Statistical summary and classification reports may be printed to facilitate the communication of quality concerns with grading personnel. Tests were conducted at a commercial forest nursery to evaluate measurement precision. Four quality control personnel measured root collar diameter, stem height, and root mass length on each of 200 conifer seedlings. The same seedlings were inspected four times by the machine vision system. Machine stem diameter measurement precision was four times greater than that of manual measurements. Machine and manual measurements had comparable precision for shoot height and root mass length.

WHITE COLLAR CRIME - Investigations

OpenAIRE

Nyagudi, Nyagudi Musandu

2014-01-01

WHITE COLLAR CRIME - Investigations Presentation By  Dr. Nyagudi MusanduForensic Criminologist 2nd International Securityand Safety Conference and Exhibition, 16th April, 2010 a forum hosted by Events Management Solutions at the Sarit Centre, Nairobi, Kenya  

Analysis of Effects of Cutting Parameters of Wire Electrical Discharge Machining on Material Removal Rate and Surface Integrity

Science.gov (United States)

Tonday, H. R.; Tigga, A. M.

2016-02-01

As wire electrical discharge machining is pioneered as a vigorous, efficient and precise and complex nontraditional machining technique, research is needed in this area for efficient machining. In this paper, the influence of various input factors of wire electrical discharge machining (WEDM) on output variable has been analyzed by using Taguchi technique and analysis of variance. The design of experiments has been done and by applying L8 orthogonal arrays method and experiments have been conducted and collected required data. The objectives of the research are to maximize the material removal rate and to minimize the surface roughness value (Ra). Surface morphology of machined workpiece has been obtained and examined by employing scanning electron microscopy (SEM) technique.

Analysis of Effects of Cutting Parameters of Wire Electrical Discharge Machining on Material Removal Rate and Surface Integrity

International Nuclear Information System (INIS)

Tonday, H. R.; Tigga, A. M.

2016-01-01

As wire electrical discharge machining is pioneered as a vigorous, efficient and precise and complex nontraditional machining technique, research is needed in this area for efficient machining. In this paper, the influence of various input factors of wire electrical discharge machining (WEDM) on output variable has been analyzed by using Taguchi technique and analysis of variance. The design of experiments has been done and by applying L8 orthogonal arrays method and experiments have been conducted and collected required data. The objectives of the research are to maximize the material removal rate and to minimize the surface roughness value (Ra). Surface morphology of machined workpiece has been obtained and examined by employing scanning electron microscopy (SEM) technique. (paper)

A self-adjusting expandable GPS collar for male elk

Science.gov (United States)

Brian L. Dick; Scott L. Findholt; Bruce K. Johnson

2013-01-01

It is a challenge to use collars on male cervids because their neck size can increase substantially during the rut and also because of growth as the animal matures. We describe how to build a self-adjusting expandable collar for yearling or adult male Rocky Mountain elk (Cervus elaphus) to which very high frequency transmitters and global...

Occupational psychosocial hazards among the emerging U.S. green collar workforce

Science.gov (United States)

Fernandez, Cristina A.; Moore, Kevin; McClure, Laura A.; Caban-Martinez, Alberto J.; LeBlanc, William G.; Fleming, Lora E.; Cifuentes, Manuel; Lee, David J.

2016-01-01

Objective To compare occupational psychosocial hazards in green collar versus non-green collar workers. Methods Standard Occupational Classification codes were used to link the 2010 National Health Interview Survey to the 2010 Occupational Information Network Database. Multivariable logistic regressions were used to predict job insecurity, work-life imbalance, and workplace harassment in green versus non-green collar workers. Results Most participants were white, non-Hispanic, 25–64 years of age, and obtained greater than a high school education. The majority reported not being harassed at work, no work-life imbalance, and no job insecurity. Relative to non-green collar workers (n=12,217), green collar workers (n=2,588) were more likely to report job insecurity (OR=1.13; 95% CI=1.02–1.26) and work-life imbalance (1.19; 1.05–1.35), but less likely to experience workplace harassment (0.77; 0.62–0.95). Conclusions Continuous surveillance of occupational psychosocial hazards is recommended in this rapidly emerging workforce. PMID:28045790

A comparative study of the effect of soft and hard cervical collars on static postural

Directory of Open Access Journals (Sweden)

Minoo Khalkhali Zavieh

2013-01-01

Full Text Available AbstractBackground and Aim: Using cervical collars is one of the treatment methods for releaving cervical pain. The effect of limb orthotics on proprioception and postural stability has been suggested. There is not sufficient studies about the effect of cervical collars on static and dynamic stability, and the effect of soft and hard collars have not been compared with one another. The objective of this study is investigating and comparing the immediate effect of soft and hard cervical collars on static postural stability in healthy young subjects. Methods & Materials: In standing position on firm surface with closed eyes, both soft and hard collars decreased the stability and there was not any significant difference among collars. In standing positions on soft surface with closed and opened eyes, using none of the soft and hard collars did not change the stability. This quasi experimental study through repeated measure method has been conducted on 65 healthy young male and female college students. Static stability was evaluated by modified Clinical Test for Sensory Interaction and Balance (CTSIB in conditions without collar and by soft and hard cervical collars and were compared between the conditions. Results: Conclusion: Our results suggest that in static conditions, without vision, both collars decrease the stability in healthy young subjects. So considering the evaluation of stability and prevention of balance disturbance during the collar prescription seems to be necessary.

LHC collars - 12 million high technology gems

CERN Multimedia

2001-01-01

Some 12 million steel collars will keep the LHC dipole magnet structures rigid. Their production has just begun. A huge job began last week: the high speed manufacturing of twelve million steel collars for the 1250 dipole magnets of the future Large Hadron Collider, LHC. The challenge is not only a matter of quantity: these collars are very high technology components because of the important role they play in the way the collider works. One of the main difficulties with the accelerator is that the magnetic field that keeps particles in orbit must have the same configuration and intensity in all the dipoles. But when the 8.33 tesla magnetic field is on -100.000 times the earth magnetic field - it produces a very strong force that can deform the 'soft' parts of the magnets, such as superconducting coils. The force loading one metre of dipole is almost comparable with the weight of a Boeing 747 - about 400 tonnes - so a huge deformation would occur without a mechanical component to keep the whole structure rigid...

Augmented collar for assistance dog

OpenAIRE

Lemasson , Germain; Lucidarme , Philippe; Pesty , Sylvie; Duhaut , Dominique

2014-01-01

In this paper we present briefly our reflexion on how to communicate with a dog using embedded devices. We also present the prototype collar we made in order to improve the communication between an assistance dog and his disabled master.

Influence of recovery method and centrifugation on epididymal sperm from collared peccaries (Pecari tajacu Linnaeus, 1758).

Science.gov (United States)

Bezerra, José Artur Brilhante; da Silva, Andréia Maria; Peixoto, Gislayne Christianne Xavier; da Silva, Mariana de Araújo; Franco de Oliveira, Moacir; Silva, Alexandre Rodrigues

2014-05-01

In order to establish protocols for gamete recovery from accidentally killed wild animals, or to take advantage of those slaughtered by captive breeders, we assess the influence of two methods on the recovery of epididymal sperm from collared peccaries, and verify the effect of centrifugation on such gametes. Genitalia from nine animals were used. For each animal, one epididymis was processed by flotation and the other was processed by retrograde flushing, both using a buffered media based on Tris. Following recovery, sperm were evaluated for motility, vigor, viability, functional membrane integrity, and morphology. A 1-mL aliquot of each sample was centrifuged, the supernatant removed, and the pellet suspended and evaluated as fresh samples. The sperm characteristics did not differ between the samples collected by flotation or retrograde flushing (P methods was affected by centrifugation. In conclusion, epididymal sperm from collared peccaries can be efficiently collected through flotation or retrograde flushing, but not when either is followed by centrifugation.

Hazard Prevention Regarding Occupational Accidents Involving Blue-Collar Foreign Workers: A Perspective of Taiwanese Manpower Agencies.

Science.gov (United States)

Chang, Huan-Cheng; Wang, Mei-Chin; Liao, Hung-Chang; Cheng, Shu-Fang; Wang, Ya-Huei

2016-07-13

Since 1989, blue-collar foreign workers have been permitted to work in Taiwanese industries. Most blue-collar foreign workers apply for jobs in Taiwan through blue-collar foreign workers' agencies. Because blue-collar foreign workers are not familiar with the language and culture in Taiwan, in occupational accident education and hazard prevention, the agencies play an important role in the coordination and translation between employees and blue-collar foreign workers. The purpose of this study is to establish the agencies' role in the occupational accidents education and hazard prevention for blue-collar foreign workers in Taiwan. This study uses a qualitative method-grounded theory-to collect, code, and analyze the data in order to understand the agencies' role in occupational accident education and hazard prevention for blue-collar foreign workers in Taiwan. The results show that the duty of agencies in occupational accident education and hazard prevention includes selecting appropriate blue-collar foreign workers, communicating between employees and blue-collar foreign workers, collecting occupational safety and health information, assisting in the training of occupational safety and health, and helping blue-collar foreign workers adapt to their lives in Taiwan. Finally, this study suggests seven important points and discusses the implementation process necessary to improve governmental policies. The government and employees should pay attention to the education/training of occupational safety and health for blue-collar foreign workers to eliminate unsafe behavior in order to protect the lives of blue-collar foreign workers.

Hazard Prevention Regarding Occupational Accidents Involving Blue-Collar Foreign Workers: A Perspective of Taiwanese Manpower Agencies

Directory of Open Access Journals (Sweden)

Huan-Cheng Chang

2016-07-01

Full Text Available Since 1989, blue-collar foreign workers have been permitted to work in Taiwanese industries. Most blue-collar foreign workers apply for jobs in Taiwan through blue-collar foreign workers’ agencies. Because blue-collar foreign workers are not familiar with the language and culture in Taiwan, in occupational accident education and hazard prevention, the agencies play an important role in the coordination and translation between employees and blue-collar foreign workers. The purpose of this study is to establish the agencies’ role in the occupational accidents education and hazard prevention for blue-collar foreign workers in Taiwan. This study uses a qualitative method—grounded theory—to collect, code, and analyze the data in order to understand the agencies’ role in occupational accident education and hazard prevention for blue-collar foreign workers in Taiwan. The results show that the duty of agencies in occupational accident education and hazard prevention includes selecting appropriate blue-collar foreign workers, communicating between employees and blue-collar foreign workers, collecting occupational safety and health information, assisting in the training of occupational safety and health, and helping blue-collar foreign workers adapt to their lives in Taiwan. Finally, this study suggests seven important points and discusses the implementation process necessary to improve governmental policies. The government and employees should pay attention to the education/training of occupational safety and health for blue-collar foreign workers to eliminate unsafe behavior in order to protect the lives of blue-collar foreign workers.

Manufacturing Gender Inequality in the New Economy: High School Training for Work in Blue-Collar Communities.

Science.gov (United States)

Sutton, April; Bosky, Amanda; Muller, Chandra

2016-08-01

Tensions between the demands of the knowledge-based economy and remaining, blue-collar jobs underlie renewed debates about whether schools should emphasize career and technical training or college-preparatory curricula. We add a gendered lens to this issue, given the male-dominated nature of blue-collar jobs and women's greater returns to college. Using the ELS:2002, this study exploits spatial variation in school curricula and jobs to investigate local dynamics that shape gender stratification. Results suggest a link between high school training and jobs in blue-collar communities that structures patterns of gender inequality into early adulthood. Although high school training in blue-collar communities reduced both men's and women's odds of four-year college enrollment, it had gender-divergent labor market consequences. Men in blue-collar communities took more blue-collar courses, had higher rates of blue-collar employment, and earned similar wages relative to otherwise comparable men from non-blue-collar communities. Women were less likely to work and to be employed in professional occupations, and they suffered severe wage penalties relative to their male peers and women from non-blue-collar communities. These relationships were due partly to high schools in blue-collar communities offering more blue-collar and fewer advanced college-preparatory courses. This curricular tradeoff may benefit men, but it appears to disadvantage women.

Horse-collar aurora: A frequent pattern of the aurora in quiet times

International Nuclear Information System (INIS)

Hones, E.W. Jr.; Craven, J.D.; Frank, L.A.; Evans, D.S.; Newell, P.T.

1989-01-01

Reported here are DE 1 auroral imager observations of an auroral configuration which is given the name ''horse-collar aurora.'' The horse-collar pattern comprises the total area of auroral emissions from a single hemisphere and derives its name from the shape of the emitting area. The pattern is found in images recorded during quiet geomagnetic conditions and is possibly related to the theta aurora, another quiet time configuration of the auroras. This initial report of the DE 1 observations illustrates the horse-collar aurora with a 2-hour images sequence that displays its basic features and shows an example of its evolution into a theta-like auroral pattern. The interplanetary magnetic field was northward during this image sequence and there is some evidence for IMF B/sub y/ influence of the temporal development of the horse-collar pattern. A preliminary statistical analysis found the horse-collar pattern appearing in one-third or more of image sequences recorded during quiet conditions; it did not appear during disturbed conditions. Further study is required to establish more fully the characteristics of the horse-collar aurora and to determine its implications concerning solar wind-magnetosphere coupling when the IMF B/sub z/ is northward. copyright American Geophysical Union 1989

Heat-Assisted Machining for Material Removal Improvement

Science.gov (United States)

Mohd Hadzley, A. B.; Hafiz, S. Muhammad; Azahar, W.; Izamshah, R.; Mohd Shahir, K.; Abu, A.

2015-09-01

Heat assisted machining (HAM) is a process where an intense heat source is used to locally soften the workpiece material before machined by high speed cutting tool. In this paper, an HAM machine is developed by modification of small CNC machine with the addition of special jig to hold the heat sources in front of the machine spindle. Preliminary experiment to evaluate the capability of HAM machine to produce groove formation for slotting process was conducted. A block AISI D2 tool steel with100mm (width) × 100mm (length) × 20mm (height) size has been cut by plasma heating with different setting of arc current, feed rate and air pressure. Their effect has been analyzed based on distance of cut (DOC).Experimental results demonstrated the most significant factor that contributed to the DOC is arc current, followed by the feed rate and air pressure. HAM improves the slotting process of AISI D2 by increasing distance of cut due to initial cutting groove that formed during thermal melting and pressurized air from the heat source.

Sedentary Behavior of White Collar Office Workers-Review

OpenAIRE

Hopkin, T. J.; Sarkar, Swarjit

2016-01-01

Aim The aim of this systematic review is to evaluate the physical activity time (PAT) of white collar office workers in order to assess the levels of sedentary activity in an office environment. Analysing the office workers PAT will not only allow an insight into how an office based job could impact a person’s overall health and wellness status, but will also allow for the development of future office based inter ventions aimed at increasing the overall physical activity among white collar of...

Dependence of Magnetic Field Quality on Collar Supplier and Dimensions in the Main LHC Dipole

CERN Document Server

Bellesia, B; Santoni, C; Todesco, E

2006-01-01

In order to keep the electro-magnetic forces and to minimize conductor movements, the superconducting coils of the main Large Hadron Collider dipoles are held in place by means of austenitic steel collars. Two suppliers provide the collars necessary for the whole LHC production, which has now reached more than 800 collared coils. In this paper we first assess if the different collar suppliers origin a noticeable difference in the magnetic field quality measured at room temperature. We then analyze the measurements of the collar dimensions carried out at the manufacturers, comparing them to the geometrical tolerances. Finally we use a magneto-static model to evaluate the expected spread in the field components induced by the actual collar dimensions. These spreads are compared to the magnetic measurements at room temperature over the magnet production in order to identify if the collars, rather than other components or assembly process, can account for the measured magnetic field effects. It has been found tha...

Job strain among blue-collar and white-collar employees as a determinant of total mortality: a 28-year population-based follow-up

Science.gov (United States)

Seitsamo, Jorma; von Bonsdorff, Monika E; Ilmarinen, Juhani; Nygård, Clas-Håkan; Rantanen, Taina

2012-01-01

Objectives To investigate the effect of job demand, job control and job strain on total mortality among white-collar and blue-collar employees working in the public sector. Design 28-year prospective population-based follow-up. Setting Several municipals in Finland. Participants 5731 public sector employees from the Finnish Longitudinal Study on Municipal Employees Study aged 44–58 years at baseline. Outcomes Total mortality from 1981 to 2009 among individuals with complete data on job strain in midlife, categorised according to job demand and job control: high job strain (high job demands and low job control), active job (high job demand and high job control), passive job (low job demand and low job control) and low job strain (low job demand and high job control). Results 1836 persons died during the follow-up. Low job control among men increased (age-adjusted HR 1.26, 95% CI 1.12 to 1.42) and high job demand among women decreased the risk for total mortality HR 0.82 (95% CI 0.71 to 0.95). Adjustment for occupational group, lifestyle and health factors attenuated the association for men. In the analyses stratified by occupational group, high job strain increased the risk of mortality among white-collar men (HR 1.52, 95% CI 1.09 to 2.13) and passive job among blue-collar men (HR 1.28, 95% CI 1.05 to 1.47) compared with men with low job strain. Adjustment for lifestyle and health factors attenuated the risks. Among white-collar women having an active job decreased the risk for mortality (HR 0.78, 95% CI 0.60 to 1.00). Conclusion The impact of job strain on mortality was different according to gender and occupational group among middle-aged public sector employees. PMID:22422919

Hybrid machining processes perspectives on machining and finishing

CERN Document Server

Gupta, Kapil; Laubscher, R F

2016-01-01

This book describes various hybrid machining and finishing processes. It gives a critical review of the past work based on them as well as the current trends and research directions. For each hybrid machining process presented, the authors list the method of material removal, machining system, process variables and applications. This book provides a deep understanding of the need, application and mechanism of hybrid machining processes.

Removal properties of low-thermal-expansion materials with rotating-sphere elastic emission machining

Directory of Open Access Journals (Sweden)

Masahiko Kanaoka et al

2007-01-01

Full Text Available Optical mirrors used in extreme ultraviolet lithography systems require a figure accuracy and a roughness of about 0.1 nm rms. In addition, mirror substrates must be low-thermal-expansion materials. Thus, in this study, we processed two low-thermal-expansion materials, ULE [K. Hrdina, B. Hanson, P. Fenn, R. Sabia, Proc. SPIE 4688 (2002 454.] (Corning Inc. and Zerodur [I. Mitra, M.J. Davis, J. Alkemper, Rolf Müller, H. Kohlmann, L. Aschke, E. Mörsen, S. Ritter, H. Hack, W. Pannhorst, Proc. SPIE 4688 (2002 462.] (SCHOTT AG, with elastic emission machining (EEM in order to evaluate the removal properties. Consequently, we successfully calculated the respective removal rates, because removal volumes were found to be proportional to process times in EEM. Moreover, we demonstrated that the surface roughness of Zerodur is reduced to 0.1 nm rms in the spatial wavelength range from 100 μm to 1 mm.

Factors associated with blue-collar workers' risk perception of cardiovascular disease.

Science.gov (United States)

Hwang, Won Ju; Hong, Oisaeng; Kim, Mi Ja

2012-12-01

The purpose of this study was to investigate the contribution of actual cardiovascular disease (CVD) risk, as well as, individual, psychosocial, and work-related factors as predictors of CVD risk perception among Korean blue-collar workers. The participants were 238 Korean blue-collar workers who worked in small companies. Data were collected through a survey; anthropometric and blood pressure measures; and blood sampling for lipid levels. Blue-collar workers had high actual CVD risk and low CVD risk perception. The significant predictors of risk perception included perceived health status, alcohol consumption, knowledge of CVD risk, actual CVD risk, decision latitude, and shift work. The model explained 26% of the variance in CVD risk perception. The result suggests when occupational health nurses are giving routine health examination in small companies, they can enhance CVD risk perception in blue-collar workers by providing essential information about CVD risk factors and personal counseling on the individual worker's CVD risk status.

Precision Obtained Using an Artificial Neural Network for Predicting the Material Removal Rate in Ultrasonic Machining

Directory of Open Access Journals (Sweden)

Gaoyan Zhong

2017-12-01

Full Text Available The present study proposes a back propagation artificial neural network (BPANN to provide improved precision for predicting the material removal rate (MRR in ultrasonic machining. The BPANN benefits from the advantage of artificial neural networks (ANNs in dealing with complex input-output relationships without explicit mathematical functions. In our previous study, a conventional linear regression model and improved nonlinear regression model were established for modelling the MRR in ultrasonic machining to reflect the influence of machining parameters on process response. In the present work, we quantitatively compare the prediction precision obtained by the previously proposed regression models and the presently proposed BPANN model. The results of detailed analyses indicate that the BPANN model provided the highest prediction precision of the three models considered. The present work makes a positive contribution to expanding the applications of ANNs and can be considered as a guide for modelling complex problems of general machining.

Criminal Trajectories of White-collar Offenders

NARCIS (Netherlands)

van Onna, J.; van der Geest, V.R.; Huisman, W.; Denkers, A.J.M.

2014-01-01

Objectives:This article analyzes the criminal development and sociodemographic and criminal profile of a sample of prosecuted white-collar offenders. It identifies trajectory groups and describes their profiles based on crime, sociodemographic, and selection offence characteristics.Methods:The

A Correlation Study between Geometry of Collared Coils and Normal Quadrupole Multipole in the Main LHC Dipoles

CERN Document Server

Bertinelli, F; Berthollon-Vitte, S; Glaude, D; Vanenkov, I

2006-01-01

The quality control implemented at all LHC dipole assemblers includes precise mechanical measurements of the geometry of collared coils. A cross-analysis performed between mechanical and magnetic measurements data shows a correlation between collared coils outer dimensions and the normal quadrupole multipole (b2) for one dipole assembler. The profile geometry of the single collars - as determined from 3D measurements at the collar suppliers and CERN - could not account alone for the significant left – right aperture asymmetry observed. This triggered a deeper investigation on different elements of the geometry of single collars. The results of this work show that the relative positioning of the collaring holes, allowing a small bending deformation of collars under the effect of coil pre-stress, is an important effect that generates a b2 multipole at the limit of specification. The study has deepened the understanding of the factors affecting collared coil geometry and field quality. The precision of 3D m...

Advantages of heavy metal collars in directional drilling and deviation control

International Nuclear Information System (INIS)

Bradley, W.B.; Murphey, C.E.; McLamore, R.T.; Dickson, L.L.

1976-01-01

A heavy, stiff-bottom drill collar can substantially improve deviation performance, theoretically increasing penetration rates by 50 to 100 percent in deviation-prone areas. This paper presents the underlying theory, practical charts on performance characteristics, and Shell Development Co.'s experience in fabricating and field testing two depleted-uranium alloy, heavy metal collars

A Comperative Study on Perceptions and Reactions of Workers: A Resear ch on Blue and White Collar Workers

Directory of Open Access Journals (Sweden)

Fikret Ateş

2014-06-01

Full Text Available The purpose of this study is to examine perception of inequality and types of reaction of white and blue collar workers. The research was conducted over 120 white collar and 159 blue collar workers in an academic institution. It was determined with correlation analysis whether there is a relation between perception of inequality and reaction towards it for two groups. A significant and positive relation has been found between inequality perceptions and reaction towards inequality of blue collar workers. No significant relation has been found for white collar workers. Factor analysis was used to determine the dimensions of inequality perceptions andreactions towards inequality of blue and white collar workers. Results show that inequality perceptions and types of reactions towards inequality differ in terms of dimensions. Equity perceptions of blue collar workers are mostly based on comparisons with colleagues and nepotist behavior of their managers. White collar workers show sensitivity to the issues like salary, promotion and status. Blue collar workers prefer to report or to persuade their managers when they face with inequality. White collar workers decide to show their reactions by using more political methods.

Unskilled blue collar workers: Bourgeois and/or authoritarian? Results from a small scale survey in Belgium

Directory of Open Access Journals (Sweden)

Hans De Witte

2007-04-01

adopted the attitudes (and life style of white collar workers, from whom they can no longer be distinguished. Lipset’s hypothesis of the ‘authoritarianism of the working class’, on the other hand, states that blue collar workers more strongly endorse a conservative attitude on socio-cultural matters and a progressive stand concerning socio-economic issues. Both hypotheses are tested using data from a small scale survey (N = 135 among unskilled blue collar workers and lower- and mid-level white collar workers from different large companies in the region of Leuven, Belgium. The results indicate that the interviewed unskilled blue collar workers still hold a set of attitudes that distinguishes them from the interviewed white collar workers. So, the ‘embourgeoisement’ thesis was refuted. Instead, the unskilled blue collar workers were more conservative on a socio-cultural level, and more progressive concerning socio-economic issues. These results are in line with Lipset’s ‘authoritarianism of the working class’ hypothesis.

White-collar crime: corporate and securities and commodities fraud.

Science.gov (United States)

Price, Marilyn; Norris, Donna M

2009-01-01

In this era of increased interest in white-collar crime, forensic psychiatrists are in a key position to study the individual characteristics of offenders. While a comprehensive theory of high-level white-collar crime should consider societal and organizational contributions, there is value in understanding the personal traits that place an individual at high risk for offending. As the impact of the criminal acts of this group has been increasingly felt by larger groups from all socioeconomic strata, there is less willingness by the public to view these crimes as victimless and harmless.

Influence of Austenitic Steel Collar Dimensions on Magnetic Field Harmonics in the LHC Main Dipole

CERN Document Server

Bellesia, B; Todesco, Ezio

2005-01-01

The influence of the geometry of the collars in the main LHC dipole on the magnetic field harmonics is analyzed. The study aims at finding if the collar geometry is the driving mechanism of field quality for some harmonics and if the two different collar suppliers give a special signature on the magnetic field. Data of more than 700 magnets of the LHC series dipoles are analyzed and discussed. The main result of the analysis is that the collar shape is the driving mechanism of the magnetic field harmonics only for b2 and a3 in one of the three Cold Mass Assemblers (Firm3), where only collars of the supplier S2 are used. Two independent observations support this fact: firstly, strong correlations between apertures of the same magnet as expected from the assembly procedure have been found. Secondly, the expected values based on the measured dimensions of the collars and on a magneto-static model agree with magnetic measurements both for the average and for the standard deviation.

Well swab collar

Energy Technology Data Exchange (ETDEWEB)

1969-04-09

A well swab collar which can be hoisted to bring well fluids upward through a pipe string is described. An elastic swab is used to swab a pipe having a predetermined diameter. The swab consists of a circular shaped elastomer body having an outer diameter a little smaller than the inner diameter of the pipe. The body is divided into multiple swab elements by ring-shaped grooves in the body. The swab element has truncated conical surfaces directed radially at an outward angle, then downward and consequently at an angle inward and then downward. (19 claims)

Evaluation and comparison of a flumethrin-imidacloprid collar and repeated monthly treatments of fipronil/(s)-methoprene to control flea, Ctenocephalides f. felis, infestations on cats for eight months.

Science.gov (United States)

Dryden, Michael W; Smith, Vicki; Davis, Wendell L; Settje, Terry; Hostetler, Joe

2016-05-17

This controlled laboratory study was designed to evaluate the efficacy of the 10 % imidacloprid/4.5 % flumethrin collar (Seresto®, Bayer Animal Health) against fleas (Ctenocephalides f. felis) on cats, when compared to fipronil (9.8 %w/w)/(s)-methoprene (11.8 % w/w) topical spot-on formulation (Frontline® Plus for Cats and Kittens, Merial). Thirty cats were randomized into three groups of ten animals based on pre-treatment flea counts: Group 1: imidacloprid/flumethrin collar; Group 2: fipronil/(s)-methoprene topical spot-on and Group 3: non-treated controls. The imidacloprid/flumethrin collars were applied one time on Day 0, while the fipronil/(s)-methoprene spot-on was administered every 30 days from Day 0 through Day 210. Cats were infested with 100 fleas on study days 0, 7, 14, 29, 59, 89, 119, 149, 179, 209 and 239. All flea counts were conducted by combing to remove fleas on post-treatment days 2, 8, 15, 30, 60, 90, 120, 150, 180, 210 and 240. The efficacy of the imidacloprid/flumethrin collar ranged from 98.2 to 100 % for eight months. The efficacy of fipronil/(s)-methoprene spot-on ranged from 68.2 to 99.9 %. Efficacy was imidacloprid/flumethrin collar group when compared to the fipronil/(s)-methoprene group on Days 90, 150 and 210 (P imidacloprid/flumethrin collar (Seresto®, Bayer Animal Health) maintained excellent ( > 98.2 %) efficacy against fleas on cats for the entire 8 month study. Monthly applications of fipronil/(s)-methoprene (Frontline® Plus for Cats and Kittens, Merial) generally had high, but variable (68.2 to 99.9 %) efficacy over the course of the eight month study. Based on the very high residual efficacy achieved by the imidacloprid/flumethrin collar in this study, veterinarians should expect that this collar will control and eliminate existing flea infestations on cats and in their in-home premises as long as every flea infested host is treated.

White-Collar Crimes and Financial Corruptions

Directory of Open Access Journals (Sweden)

Fatih ŞENTÜRK

2013-12-01

Full Text Available Crime, defined as act which is contrary to the law, creates negative influence in the society both economically and spiritually. There are various factors like professional experience as well as biological, psychological and sociological ones that make individuals turn to crime. Edwin Sutherland claim that life experiences and some facts learned from the environment account for occupational crimes in his study on the theory of crime in 1939. White-collar crime, which is perhaps the most important of types of crime in terms of havoc and committed by the superior contrary to common belief, has much more influence than conventional crime. This crime, which inflict significant financial loses and psychological collapse on states, communities, businesses and people, are committed by well-respected professionals in their business. In this study, white collar crimes are examined with conceptual view and detailed. Besides, this study explain this type of crime is so forceful, by giving remarkable examples on economic losses.

Cattle behaviour classification from collar, halter, and ear tag sensors

Directory of Open Access Journals (Sweden)

A. Rahman

2018-03-01

Full Text Available In this paper, we summarise the outcome of a set of experiments aimed at classifying cattle behaviour based on sensor data. Each animal carried sensors generating time series accelerometer data placed on a collar on the neck at the back of the head, on a halter positioned at the side of the head behind the mouth, or on the ear using a tag. The purpose of the study was to determine how sensor data from different placement can classify a range of typical cattle behaviours. Data were collected and animal behaviours (grazing, standing or ruminating were observed over a common time frame. Statistical features were computed from the sensor data and machine learning algorithms were trained to classify each behaviour. Classification accuracies were computed on separate independent test sets. The analysis based on behaviour classification experiments revealed that different sensor placement can achieve good classification accuracy if the feature space (representing motion patterns between the training and test animal is similar. The paper will discuss these analyses in detail and can act as a guide for future studies.

Comparison of Aerosol Delivery by Face Mask and Tracheostomy Collar.

Science.gov (United States)

Bugis, Alaa A; Sheard, Meryl M; Fink, James B; Harwood, Robert J; Ari, Arzu

2015-09-01

The purpose of this study was to compare the performance of a tracheostomy collar, Wright mask, and aerosol mask attached to a jet nebulizer in facilitating aerosolized medication delivery to the lungs. We also compared albuterol delivery with open versus closed fenestration and determined the effect of inspiratory-expiratory ratio (I:E) on aerosol delivery. Albuterol (2.5 mg/3 mL) was administered to an in vitro model consisting of an adult teaching mannequin extrathoracic and upper airway with stoma intubated with an 8-mm fenestrated tracheostomy tube. The cuff was deflated. A collecting filter at the level of the bronchi was connected to a breathing simulator at a tidal volume of 400 mL, breathing frequency of 20 breaths/min, and I:E of 2:1 and 1:2. A jet nebulizer was operated with O2 at 8 L/min. Each interface was tested in triplicate. The flow was discontinued at the end of nebulization. For each test, the nebulizer was attached to a tracheostomy collar with the fenestration open or closed, a Wright mask, or an aerosol mask. Drug was analyzed by spectrophotometry (276 nm). A paired t test and analysis of variance were performed (P mask (4.1 ± 0.6%) and aerosol mask (3.5 ± 0.04%) were both less than with the tracheostomy collar under either condition (P mask (7.2 ± 0.6%), and aerosol mask (6.1 ± 0.5%). In an adult tracheostomy model, the tracheostomy collar delivered more aerosol to the bronchi than the Wright or aerosol mask. An I:E of 2:1 caused greater aerosol deposition compared with an I:E of 1:2. During aerosol administration via a tracheostomy collar, closing the fenestration improved aerosol delivery. Copyright © 2015 by Daedalus Enterprises.

Investigation of material removal rate and surface roughness during wire electrical discharge machining (WEDM of Inconel 625 super alloy by cryogenic treated tool electrode

Directory of Open Access Journals (Sweden)

Ashish Goyal

2017-10-01

Full Text Available The present investigation focuses the effect of process parameters on material removal rate (MRR and surface roughness (Ra in wire electric discharge machining of Inconel 625. Machining was done by using a normal zinc coated wire and cryogenic treated zinc coated wire. The experiments were performed by considering different process parameters viz. tool electrode, current intensity, pulse on time, pulse off time, wire feed and wire tension. The thickness of work material and dia. of wire are kept constant. Taguchi L18 (21 * 35 orthogonal array of experimental design is used to perform the experiments. Analysis of variance (ANOVA is employed to optimize the material removal rate and surface roughness. Based on analysis it is found that pulse on time, tool electrode and current intensity are the significant parameters that affect the material removal rate and surface roughness. The scanning electron microscopy (SEM are used to identify the microstructure of the machined work piece.

Mind over matter: exploring job stress among female blue-collar workers.

Science.gov (United States)

Griffin-Blake, C Shannon; Tucker, Pattie J; Liburd, Leandris

2006-12-01

Although overall health has been defined holistically as the integration of a person's optimal mental, physical, social, intellectual, and spiritual well-being, a mental health focus remains on the fringe of many public health efforts. This report describes recent efforts by the Centers for Disease Control and Prevention (CDC) to explore job stress among female blue-collar workers. Using a more holistic approach to understand its impact on blue-collar women's overall health, health-related quality of life (HRQOL) was used to assess optimal human performance. Attempting to encapsulate how overall health affects one's ability to participate and fulfill daily personal/professional tasks, HRQOL yields a broader understanding of the interaction between psychological well-being (mind) and physical functioning (matter). Embedding CDC HRQOL-4 measures into a questionnaire used as part of a larger mixed methods project, blue-collar women responded to questions about their health, including both mental and physical. For these female workers, mental health appeared to be of greater consequence, which could be interpreted as mind being more significant than matter. This paper highlights the findings related to HRQOL issues experienced by these female blue-collar workers and summarizes recommendations for effective individual and organizational approaches to address job stress.

Cervical spine collar clearance in the obtunded adult blunt trauma patient: a systematic review and practice management guideline from the Eastern Association for the Surgery of Trauma.

Science.gov (United States)

Patel, Mayur B; Humble, Stephen S; Cullinane, Daniel C; Day, Matthew A; Jawa, Randeep S; Devin, Clinton J; Delozier, Margaret S; Smith, Lou M; Smith, Miya A; Capella, Jeannette M; Long, Andrea M; Cheng, Joseph S; Leath, Taylor C; Falck-Ytter, Yngve; Haut, Elliott R; Como, John J

2015-02-01

With the use of the framework advocated by the Grading of Recommendations Assessment, Development and Evaluation (GRADE) Working Group, our aims were to perform a systematic review and to develop evidence-based recommendations that may be used to answer the following PICO [Population, Intervention, Comparator, Outcomes] question:In the obtunded adult blunt trauma patient, should cervical collar removal be performed after a negative high-quality cervical spine (C-spine) computed tomography (CT) result alone or after a negative high-quality C-spine CT result combined with adjunct imaging, to reduce peri-clearance events, such as new neurologic change, unstable C-spine injury, stable C-spine injury, need for post-clearance imaging, false-negative CT imaging result on re-review, pressure ulcers, and time to cervical collar clearance? Our protocol was registered with the PROSPERO international prospective register of systematic reviews on August 23, 2013 (REGISTRATION NUMBER: CRD42013005461). Eligibility criteria consisted of adult blunt trauma patients 16 years or older, who underwent C-spine CT with axial thickness of less than 3 mm and who were obtunded using any definition.Quantitative synthesis via meta-analysis was not possible because of pre-post, partial-cohort, quasi-experimental study design limitations and the consequential incomplete diagnostic accuracy data. Of five articles with a total follow-up of 1,017 included subjects, none reported new neurologic changes (paraplegia or quadriplegia) after cervical collar removal. There is a worst-case 9% (161 of 1,718 subjects in 11 studies) cumulative literature incidence of stable injuries and a 91% negative predictive value of no injury, after coupling a negative high-quality C-spine CT result with 1.5-T magnetic resonance imaging, upright x-rays, flexion-extension CT, and/or clinical follow-up. Similarly, there is a best-case 0% (0 of 1,718 subjects in 11 studies) cumulative literature incidence of unstable

Postmortem findings in collared peccaries raised in captivity in northeastern Brazil

Directory of Open Access Journals (Sweden)

Jael S. Batista

2014-11-01

Full Text Available This study is a retrospective examination of diseases in collared peccaries that were diagnosed by the Veterinary Pathology Laboratory, Universidade Federal Rural do Semiárido. Necropsy and histological examination were performed from 2005 to 2010. Of the 50 necropsied collared peccaries, 24% died due to restraint and capture myopathy; 18% died from trauma; and the remainder was diagnosed with splenic hemangioma (6%, enterolithiasis (6%, gastritis (6%, gastric ulcer (4%, intestinal volvulus (4%, gastric volvulus (2%, mammary carcinoma (2%, polycystic kidney disease (2%, pyometra (2%, and suppurative bronchopneumonia (2%. Twelve animals remained undiagnosed, seven of which (14% were in advanced autolytic condition and five of which (10% had no gross or microscopic lesions that were compatible with disease. This paper describes illnesses that have not been reported in the collared peccary, focusing on their clinical and pathological aspects.

GPS radio collar 3D performance as influenced by forest structure and topography

Science.gov (United States)

R. Scott Gamo; Mark A. Rumble; Fred Lindzey; Matt Stefanich

2000-01-01

Global Positioning System (GPS) telemetry enables biologists to obtain accurate and systematic locations of animals. Vegetation can block signals from satellites to GPS radio collars. Therefore, a vegetation dependent bias to telemetry data may occur which if quantified, could be accounted for. We evaluated the performance of GPS collars in 6 structural stage...

An integrative review: work environment factors associated with physical activity among white-collar workers.

Science.gov (United States)

Lin, Yun-Ping; McCullagh, Marjorie C; Kao, Tsui-Sui; Larson, Janet L

2014-02-01

The purpose of this review is to synthesize the research evidence for the role of the work environment-workplace physical activity policies and resources and job strain factors-in explaining physical activity in white-collar workers. White-collar workers are at risk for developing a sedentary lifestyle, which contributes to all-cause mortality. Understanding how work environment can influence worker physical activity is important for the development of effective interventions. We reviewed 15 research articles that describe the relationship between work environment factors and physical activity in predominantly white-collar workers. Relatively consistent evidence was found for the effects of supportive workplace policies and resources. Weak evidence was found for the effects of job strain. Both work environment factors have the potential to influence physical activity but require further exploration to fully understand their contribution to physical activity in white-collar workers. Limitations and implications are discussed.

Augmenting the osseointegration of endoprostheses using laser-sintered porous collars: an in vivo study.

Science.gov (United States)

Mumith, A; Coathup, M; Chimutengwende-Gordon, M; Aston, W; Briggs, T; Blunn, G

2017-02-01

Massive endoprostheses rely on extra-cortical bone bridging (ECBB) to enhance fixation. The aim of this study was to investigate the role of selective laser sintered (SLS) porous collars in augmenting the osseointegration of these prostheses. The two novel designs of porous SLS collars, one with small pores (Ø700 μm, SP) and one with large pores (Ø1500 μm, LP), were compared in an ovine tibial diaphyseal model. Osseointegration of these collars was compared with that of a clinically used solid, grooved design (G). At six months post-operatively, the ovine tibias were retrieved and underwent radiological and histological analysis. Porous collars provided a significantly greater surface (p direct ingrowth of more bone and are better than current designs which rely on surface ongrowth and ECBB. Cite this article: Bone Joint J 2017;99-B:276-82. ©2017 The British Editorial Society of Bone & Joint Surgery.

Does patency after a vein collar and PTFE-bypass depend on sex and age?

DEFF Research Database (Denmark)

Lundgren, F; Schroeder, Torben Veith

2012-01-01

Randomized studies evaluating the effect of a vein collar at the distal anastomosis of PTFE-grafts show conflicting results. The study of the Joint Vascular Research Group (JVRG) of UK found improved primary patency while the Scandinavian Miller Collar Study (SCAMICOS) found neither any effect...

Occupational contact dermatitis in blue-collar workers: results from a multicentre study from the Danish Contact Dermatitis Group (2003-2012).

Science.gov (United States)

Schwensen, Jakob F; Menné, Torkil; Veien, Niels K; Funding, Anne T; Avnstorp, Christian; Østerballe, Morten; Andersen, Klaus E; Paulsen, Evy; Mørtz, Charlotte G; Sommerlund, Mette; Danielsen, Anne; Andersen, Bo L; Thormann, Jens; Kristensen, Ove; Kristensen, Berit; Vissing, Susanne; Nielsen, Niels H; Thyssen, Jacob P; Johansen, Jeanne D

2014-12-01

Blue-collar workers have a high risk of occupational contact dermatitis, but epidemiological studies are scarce. To investigate allergic contact dermatitis in blue-collar workers with dermatitis registered by the Danish Contact Dermatitis Group. A retrospective analysis of patch test data from 1471 blue-collar workers and 1471 matched controls tested between 2003 and 2012 was performed. A logistic regression was used to test for associations. The blue-collar workers often had occupational hand dermatitis (p dermatitis was less commonly observed among blue-collar workers (19.6%) than among controls (23.9%) (p = 0.005). Allergens with a statistically significant association with the occupational group of blue-collar workers were epoxy resins, methyldibromo glutaronitrile, 2-bromo-2-nitro-1,3-propanediol, potassium dichromate, and methylchloroisothiazolinone (MCI)/methylisothiazolinone (MI). The following occupations were additionally identified as risk factors for contact sensitization to MCI/MI and MI, epoxy resins, and potassium dichromate, respectively: painting, construction work, and tile setting/terrazzo work. Contact allergy is a major problem among blue-collar workers. The data indicate a healthy worker effect among blue-collar workers diagnosed with dermatitis, as blue-collar workers were diagnosed significantly less often with atopic dermatitis than were controls. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Does Shoe Collar Height Influence Ankle Joint Kinematics and Kinetics in Sagittal Plane Maneuvers?

Science.gov (United States)

Yang, Yang; Fang, Ying; Zhang, Xini; He, Junliang; Fu, Weijie

2017-01-01

The Objective of the study is to investigate the effects of basketball shoes with different collar heights on ankle kinematics and kinetics and athletic performance in different sagittal plane maneuvers. Twelve participants who wore high-top and low-top basketball shoes (hereafter, HS and LS, respectively) performed a weight-bearing dorsiflexion (WB-DF) maneuver, drop jumps (DJs), and lay-up jumps (LJs). Their sagittal plane kinematics and ground reaction forces were recorded using the Vicon motion capture system and Kistler force plates simultaneously. Moreover, ankle dorsiflexion and plantarflexion angles, moment, power, stiffness, and jump height were calculated. In the WB-DF test, the peak ankle dorsiflexion angle (p = 0.041) was significantly smaller in HS than in LS. Additionally, the peak ankle plantarflexion moment (p = 0.028) and power (p = 0.022) were significantly lower in HS than in LS during LJs but not during DJs. In both jumping maneuvers, no significant differences were found in the jump height or ankle kinematics between the two shoe types. According to the WB-DF test, increasing shoe collar height can effectively reduce the ankle range of motion in the sagittal plane. Although the HS did not restrict the flexion–extension performance of the ankle joint during two jumping maneuvers, an increased shoe collar height can reduce peak ankle plantarflexion moment and peak power during the push-off phase in LJs. Therefore, a higher shoe collar height should be used to circumvent effects on the partial kinetics of the ankle joint in the sagittal plane. Key points An increased shoe collar height effectively reduced ankle joint ROM in the sagittal plane in weight-bearing dorsiflexion maneuver. Shoe collar height did not affect sagittal plane ankle kinematics and had no effect on performance during realistic jumping. Shoe collar height can affect the ankle plantarflexion torque and peak power during the push-off phase in lay-up jump. PMID:29238255

Optimization of water removal in the press section of a paper machine

Directory of Open Access Journals (Sweden)

D. M. D. Drummond

2010-06-01

Full Text Available An optimization problem regarding water removal in the press section of a paper machine is considered in this work. The proposed model tries to minimize a cost function comprising the replacement of the felts in the press section, the cost of energy to operate the press and the cost of energy in the drying section, while satisfying the constraints of water mass balance in the process. The model is classified as a mixed-integer nonlinear program (MINLP in which the most important decisions are: a the sequence of paper to produce or when to produce the paper; b the need to exchange the felts; and c when to exchange the felts. Numerical examples are presented to illustrate the performance of the model.

Decent Work in the Chinese Apparel Industry: Comparative Analysis of Blue-Collar and White-Collar Garment Workers

Directory of Open Access Journals (Sweden)

Caixia Chen

2017-08-01

Full Text Available Addressing labor issues in the apparel industry is significantly important due to customers’ increasing awareness of poor working conditions and growing labor crises in apparel production locations worldwide. Decent work is a key element to achieving fair and harmonious employment, but is not always evident in global apparel production networks. This study examines the working conditions in China’s garment manufacturing industry, which employs more than 10 million workers. A survey was administered to 313 blue-collar workers and 228 white-collar workers on issues related to decent work, including workers’ concerns, satisfaction levels and attitudes towards decent work. Regression analysis showed that workers’ attitudes are significantly related to age, education level, service length and monthly wage. Gap analysis revealed poor understanding of decent work and low satisfaction with primary indicators of decent work. However, results suggest that workers increasingly value soft factors and the overall work experience, not only financial benefits. Cluster analysis identified four clusters of workers. This study contributes to understanding garment worker perceptions of decent work and provides implications for the operationalization of decent work in China’s garment manufacturing industry.

Ergonomic assessment of enhanced protection under body armour combat shirt neck collars.

Science.gov (United States)

Breeze, John; Granger, C J; Pearkes, T D; Clasper, J C

2014-03-01

Combat neck injury due to explosively propelled fragments is a significant cause of mortality and long-term morbidity in UK soldiers deployed on current operations. Reinforcing the collar of the existing under body armour combat shirt (UBACS) has been suggested as a potential method for reducing the incidence of combat neck injury. 20 soldiers serving in Afghanistan objectively compared three designs of enhanced protection UBACS (EP-UBACS) using 10 representative military tasks against a baseline of a standard UBACS. Each EP-UBACS design was trialled using three constituent materials: two layers of para-aramid felt, one layer of ultra high molecule weight polyethylene (UHMWPE) felt or two layers of a silk fabric. Subjective assessment of these nine configurations in terms of comfort, heat dissipation and overall acceptability were compared with the standard UBACS using a χ² test. All military tasks could be performed with all nine configurations of EP-UBACS. Although silk was the most comfortable material, it was not functionally practical in any of the three designs. Crossover collars incorporating UHMWPE or para-aramid were the only two of the nine configurations to demonstrate similar user acceptability to a standard UBACS. The EP-UBACS has the potential to provide neck protection without reducing performance incorporating materials analogous to either of the felts assessed in this study. The collar should provide stand-off from the skin to improve heat dissipation and comfort, which can be maximised by changing the current UBACS collar shape to one that crosses over at the front. Should a zip be desired, it should be moved to one side of the midline to reduce rubbing on the chin and be covered with ballistic protective material. Additional semi-circles of silk beneath the collar at the front and back would improve protection without affecting comfort.

Pneumatic soil removal tool

International Nuclear Information System (INIS)

Neuhaus, J.E.

1992-01-01

A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw. 3 figs

Pneumatic soil removal tool

Science.gov (United States)

Neuhaus, John E.

1992-01-01

A soil removal tool is provided for removing radioactive soil, rock and other debris from the bottom of an excavation, while permitting the operator to be located outside of a containment for that excavation. The tool includes a fixed jaw, secured to one end of an elongate pipe, which cooperates with a movable jaw pivotably mounted on the pipe. Movement of the movable jaw is controlled by a pneumatic cylinder mounted on the pipe. The actuator rod of the pneumatic cylinder is connected to a collar which is slidably mounted on the pipe and forms part of the pivotable mounting assembly for the movable jaw. Air is supplied to the pneumatic cylinder through a handle connected to the pipe, under the control of an actuator valve mounted on the handle, to provide movement of the movable jaw.

Removal performance and water quality analysis of paper machine white water in a full-scale wastewater treatment plant.

Science.gov (United States)

Shi, Shuai; Wang, Can; Fang, Shuai; Jia, Minghao; Li, Xiaoguang

2017-06-01

Paper machine white water is generally characterized as a high concentration of suspended solids and organic matters. A combined physicochemical-biological and filtration process was used in the study for removing pollutants in the wastewater. The removal efficiency of the pollutant in physicochemical and biological process was evaluated, respectively. Furthermore, advanced technology was used to analyse the water quality before and after the process treatment. Experimental results showed that the removal efficiency of suspend solids (SS) of the system was above 99%, while the physicochemical treatment in the forepart of the system had achieved about 97%. The removal efficiency of chemical oxygen demand (COD) and colour had the similar trend after physicochemical treatment and were corresponding to the proportion of suspended and the near-colloidal organic matter in the wastewater. After biological treatment, the removal efficiency of COD and colour achieved were about 97% and 90%, respectively. Furthermore, molecular weight (MW) distribution analysis showed that after treatment low MW molecules (analysis showed that most humic-like substances were effectively removed during the treatment. The analyses of gas chromatography/mass spectrometry showed that the composition of organic matter in the wastewater was not complicated. Methylsiloxanes were the typical organic components in the raw wastewater and most of them were removed after treatment.

78 FR 4167 - Certain Electronic Bark Control Collars; Notice of Receipt of Complaint; Solicitation of Comments...

Science.gov (United States)

2013-01-18

... INTERNATIONAL TRADE COMMISSION [Docket No. 2932] Certain Electronic Bark Control Collars; Notice.... International Trade Commission. ACTION: Notice. SUMMARY: Notice is hereby given that the U.S. International Trade Commission has received a complaint entitled Certain Electronic Bark Control Collars, DN 2932; the...

28 CFR 36.304 - Removal of barriers.

Science.gov (United States)

2010-07-01

..., vending machines, display racks, and other furniture; (5) Repositioning telephones; (6) Adding raised.... These measures include, for example, removal of obstructing furniture or vending machines, widening of...) General. A public accommodation shall remove architectural barriers in existing facilities, including...

Offshoring White-Collar Work: An Explorative Investigation of the Processes and Mechanisms in Two Danish Manufacturing Firms

DEFF Research Database (Denmark)

Slepniov, Dmitrij; Larsen, Marcus Møller; Wæhrens, Brian Vejrum

2010-01-01

of this paper is two folded: to explain why knowledge-intensive service work in manufacturing firms is increasingly subject to offshoring and to understand the effects of this process on integration mechanisms for the firms involved. The empirical part of the study is based on two qualitative case studies...... of Danish manufacturers, and on the basis of these, we first argue that the drivers of white-collar work offshoring in many respects are parallel to those of the earlier wave of blue-collar work offshoring. However, the existing offshoring and outsourcing frameworks do not necessarily adequately address....... By relating white-collar work offshoring to integration means companies instigate to manage it, we attempt to bridge the existing knowledge gaps and advance understanding of the process of white-collar work offshoring and its implications....

Machinability of advanced materials

CERN Document Server

Davim, J Paulo

2014-01-01

Machinability of Advanced Materials addresses the level of difficulty involved in machining a material, or multiple materials, with the appropriate tooling and cutting parameters.  A variety of factors determine a material's machinability, including tool life rate, cutting forces and power consumption, surface integrity, limiting rate of metal removal, and chip shape. These topics, among others, and multiple examples comprise this research resource for engineering students, academics, and practitioners.

Mechanical behaviour of a closed collar model for an 11.5 T dipole magnet

International Nuclear Information System (INIS)

Emden, W. van; Daum, C.; Geerinck, J.

1992-03-01

A 10 cm long model of an 11.5 T Nb 3 Sn accelerator dipole magnet, which will be built in the Netherlands, with a closed ring shaped collar has been constructed. Measurements of the collar deformation and the prestress at the poles have been made with a structural analysis using the Finite Element Method (FEM) of the code ANSYS. (author). 11 refs.; 18 figs.; 7 tabs

Dotted collar placed around carotid artery induces asymmetric neointimal lesion formation in rabbits without intravascular manipulations

Directory of Open Access Journals (Sweden)

Kivelä Antti

2012-10-01

Full Text Available Abstract Background Neointimal formation in atherosclerosis has been subject for intense research. However, good animal models mimicking asymmetrical lesion formation in human subjects have been difficult to establish. The aim of this study was to develop a model which would lead to the formation of eccentric lesions under macroscopically intact non-denuded endothelium. Methods We have developed a new collar model where we placed two cushions or dots inside the collar. Arterial lesions were characterized using histology and ultrasound methods. Results When this dotted collar was placed around carotid and femoral arteries it produced asymmetrical pressure on adventitia and a mild flow disturbance, and hence a change in shear stress. Our hypothesis was that this simple procedure would reproducibly produce asymmetrical lesions without any intraluminal manipulations. Intima/media ratio increased towards the distal end of the collar with the direction of blood flow under macroscopically intact endothelium. Macrophages preferentially accumulated in areas of the thickest neointima thus resembling early steps in human atherosclerotic plaque formation. Proliferating cells in these lesions and underlying media were scarce at eight weeks time point. Conclusion The improved dotted collar model produces asymmetrical human-like atherosclerotic lesions in rabbits. This model should be useful in studies regarding the pathogenesis and formation of eccentric atherosclerotic lesions.

The development and validation of a job crafting measure for use with blue-collar workers

DEFF Research Database (Denmark)

Nielsen, Karina; Abildgaard, Johan Simonsen

2012-01-01

Abstract Job crafting describes a set of proactive behaviours in which employees may engage to shape their work in order to minimize hindering job demands and maximize resources and challenging demands. Such behaviours may be particularly important among blue-collar workers whose jobs are charact......Abstract Job crafting describes a set of proactive behaviours in which employees may engage to shape their work in order to minimize hindering job demands and maximize resources and challenging demands. Such behaviours may be particularly important among blue-collar workers whose jobs...... are characterized by poor working conditions and low well-being. We present the development and adaptation of a job crafting measure that may be used among blue-collar workers, based on an existing scale by Tims, Bakker, and Derks (2012) that was not specifically developed for blue-collar workers. We test......, increasing social job resources, increasing quantitative demands and decreasing hindering job demands. These can be reliably measured with 15 items. The measure shows acceptable discriminant and criterion validity, and test-retest reliability. The findings extend the application of the original questionnaire...

Australian blue-collar men's health and well-being: contextual issues for workplace health promotion interventions.

Science.gov (United States)

Du Plessis, Karin; Cronin, David; Corney, Tim; Green, Emma

2013-09-01

In Australia, blue-collar workers are predominantly male and form a unique and large (approximately 30%) subset of the Australian workforce. They exhibit particular health-related issues and, in comparison to other groups, often a lack of health promoting behavior. This article briefly discusses the Australian context and some of the key health issues blue-collar men face, in particular as it relates to construction workers. It reviews the impact of gender and socioeconomic factors in designing workplace health promotion interventions. This article considers practice strategies for health promoters in a specific workplace setting: it looks at meta-factors and industry-based contextual factors, including barriers to implementation and participation, while addressing common misconceptions about Australian blue-collar workers.

Gray Wolf (Canis lupus) movements and behavior around a kill site and implications for GPS collar studies

Science.gov (United States)

Mech, L. David

2011-01-01

Global Positioning System (GPS) radio-collars are increasingly used to estimate Gray Wolf (Canis lupus) kill rates. In interpreting results from this technology, researchers make various assumptions about wolf behavior around kills, yet no detailed description of this behavior has been published. This article describes the behavior of six wolves in an area of constant daylight during 30 hours, from when the pack killed a Muskox (Ovibos moschatus) calf and yearling on Ellesmere Island, Nunavut, Canada, to when they abandoned the kill remains. Although this is only a single incident, it demonstrates one possible scenario of pack behavior around a kill. Combined with the literature, this observation supports placing a radio-collar on the breeding male to maximize finding kills via GPS collars and qualifying results depending on whatever other information is available about the collared wolf's pack.

HDM model magnet mechanical behavior with high manganese steel collars

International Nuclear Information System (INIS)

Snyder, J.R.

1994-01-01

Westinghouse Electric Corporation (WEC) is presently under contract to the SSCL to design, develop, fabricate, and deliver superconducting dipole magnets for the High Energy Booster (HEB). As a first step toward these objectives SSCL supplied a design for short model magnets of 1.8 m in length (DSB). This design was used as a developmental tool for all phases of engineering and fabrication. Mechanical analysis of the HDM (High Energy Booster Dipole Magnets) model magnet design as specified by SSCL was performed with the following objectives: (1) to develop a thorough understanding of the design; (2) to review and verify through analytical and numerical analyses the SSCL model magnet design; (3) to identify any deficiencies that would violate design parameters specified in the HDM Design Requirements Document. A detailed analysis of the model magnet mechanical behavior was pursued by constructing a quarter section finite element model and solving with the ANSYS finite element code. Collar materials of Nitronic-40 and High-Manganese steel were both considered for the HEB model magnet program with the High-Manganese being the final selection. The primary mechanical difference in the two materials is the much lower thermal contraction of the High-Manganese steel. With this material the collars will contract less than the enclosing yoke producing an increased collar yoke interference during cooldown

Discovery of a second population of white-collared seedeaters, Sporophila torqueola (Passeriformes: emberizidae) along the Rio Grande of Texas

Science.gov (United States)

Woodin, Marc C.; Skoruppa, Mary K.; Blacklock, Gene W.; Hickman, Graham C.

1999-01-01

The range of the white-collared seedeater (Sporophila torqueola), a tropical grassland species, extends from Central America northward along both coasts of Mexico (Eitniear, 1997), including Tamaulipas and Nuevo Leon (Howell and Webb, 1995). White-collared seedeaters historically occurred commonly in extreme southern Texas (Oberholser, 1974; Rappole and Blacklock, 1994). However, since about 1950, white-collared seedeaters have undergone a precipitous decline in south Texas. Studies during 1994-1996 identified only seven to nine breeding pairs in the only population known to occur in Texas, located ca. 55 km downriver of Laredo, Texas, in Zapata Co. (Eitniear, 1997). Outside of the historical range, very few records are documented. Oberholser (1974) reported that three white-collared seed- eater specimens were collected in 1948 in Webb Co., northwest of Laredo, and Arnold (1980) also collected a white-collared seedeater in Webb Co. Vagrants also have been sighted as far afield as Corpus Christi (Blacklock, 1964), ca. 200 km north of the Rio Grande (Fig. 1).

The Origin of Black Smock and White Collar

Science.gov (United States)

Hesapcioglu, Muhsin; Meseci Giorgetti, Filiz

2009-01-01

Although there are many empirical studies on the functions of school uniform, studies which focus on the origins of school uniform are neglected. Purpose of this study is to reveal historical origins of black smock and white collar. To achieve this purpose, a qualitative research method was adopted. As a result of the research, it was determined…

Shoe collar height effect on athletic performance, ankle joint kinematics and kinetics during unanticipated maximum-effort side-cutting performance.

Science.gov (United States)

Lam, Gilbert Wing Kai; Park, Eun Jung; Lee, Ki-Kwang; Cheung, Jason Tak-Man

2015-01-01

Side-step cutting manoeuvres comprise the coordination between planting and non-planting legs. Increased shoe collar height is expected to influence ankle biomechanics of both legs and possibly respective cutting performance. This study examined the shoe collar height effect on kinematics and kinetics of planting and non-planting legs during an unanticipated side-step cutting. Fifteen university basketball players performed maximum-effort side-step cutting to the left 45° direction or a straight ahead run in response to a random light signal. Seven successful cutting trials were collected for each condition. Athletic performance, ground reaction force, ankle kinematics and kinetics of both legs were analysed using paired t-tests. Results indicated that high-collar shoes resulted in less ankle inversion and external rotation during initial contact for the planting leg. The high-collar shoes also exhibited a smaller ankle range of motion in the sagittal and transverse planes for both legs, respectively. However, no collar effect was found for ankle moments and performance indicators including cutting performance time, ground contact time, propulsion ground reaction forces and impulses. These findings indicated that high-collar shoes altered ankle positioning and restricted ankle joint freedom movements in both legs, while no negative effect was found for athletic cutting performance.

Simulations of a PSD Plastic Neutron Collar for Assaying Fresh Fuel

Energy Technology Data Exchange (ETDEWEB)

Hausladen, Paul [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Newby, Jason [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); McElroy, Robert Dennis [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-11-01

The potential performance of a notional active coincidence collar for assaying uranium fuel based on segmented detectors constructed from the new PSD plastic fast organic scintillator with pulse shape discrimination capability was investigated in simulation. Like the International Atomic Energy Agency's present Uranium Neutron Collar for LEU (UNCL), the PSD plastic collar would also function by stimulating fission in the ²³⁵U content of the fuel with a moderated ²⁴¹Am/Li neutron source and detecting instances of induced fission via neutron coincidence counting. In contrast to the moderated detectors of the UNCL, the fast time scale of detection in the scintillator eliminates statistical errors due to accidental coincidences that limit the performance of the UNCL. However, the potential to detect a single neutron multiple times historically has been one of the properties of organic scintillator detectors that has prevented their adoption for international safeguards applications. Consequently, as part of the analysis of simulated data, a method was developed by which true neutron-neutron coincidences can be distinguished from inter-detector scatter that takes advantage of the position and timing resolution of segmented detectors. Then, the performance of the notional simulated coincidence collar was evaluated for assaying a variety of fresh fuels, including some containing burnable poisons and partial defects. In these simulations, particular attention was paid to the analysis of fast mode measurements. In fast mode, a Cd liner is placed inside the collar to shield the fuel from the interrogating source and detector moderators, thereby eliminating the thermal neutron flux that is most sensitive to the presence of burnable poisons that are ubiquitous in modern nuclear fuels. The simulations indicate that the predicted precision of fast mode measurements is similar to what can be achieved by the present UNCL in thermal mode. For example, the

Evaluation of clinical efficacy and safety of cervical trauma collars: differences in immobilization, effect on jugular venous pressure and patient comfort

Science.gov (United States)

2014-01-01

Background Concern has been raised that cervical collars may increase intracranial pressure in traumatic brain injury. The purpose of this study was to compare four types of cervical collars regarding efficacy of immobilizing the neck, effect on jugular venous pressure (JVP), as a surrogate for possible effect on intracranial pressure, and patient comfort in healthy volunteers. Methods The characteristics of four widely used cervical collars (Laerdal Stifneck® (SN), Vista® (VI), Miami J Advanced® (MJ), Philadelphia® (PH)) were studied in ten volunteers. Neck movement was measured with goniometry, JVP was measured directly through an endovascular catheter and participants graded the collars according to comfort on a scale 1–5. Results The mean age of participants was 27 ± 5 yr and BMI 26 ± 5. The mean neck movement (53 ± 9°) decreased significantly with all the collars (p  MJ > SN > PH). Conclusion Stifneck and Miami J collars offered the most efficient immobilization of the neck with the least effect on JVP. Vista and Miami J were the most comfortable ones. The methodology used in this study may offer a new approach to evaluate clinical efficacy and safety of neck collars and aid their continued development. PMID:24906207

Habitat Selection and Activity Pattern of GPS Collared Sumateran Tigers

Directory of Open Access Journals (Sweden)

Dolly Priatna

2012-12-01

Full Text Available Although translocation has been used in mitigating human-carnivore conflict for decades, few studies have been conducted on the behavioral ecology of released animals. Such information is necessary in the context of sustainable forest management. In this study we determine the type of land cover used as main habitat and examine the activity pattern of translocated tigers. Between 2008 and 2010 we captured six conflict tigers and translocated them 74-1,350 km from their capture sites in Sumatera. All tigers were fitted with global positioning system (GPS collars. The collars were set to fix 24-48 location coordinates per day.  All translocated tigers showed a preference for a certain habitat type within their new home range, and tended to select the majority of natural land cover type within the landscape as their main habitat, but the availability of natural forest habitat within the landscape remains essensial for their survival. The activity of male translocated tigers differed significantly between the six time intervals of 24 hours, and their most active periods were in the afternoon (14:00-18:00 hours and in the evening (18:00-22:00 hours. Despite being preliminary, the findings of this study-which was the first such study conducted in Sumatera-highlight the conservation value of tiger translocation and provide valuable information for improving future management of conflict tigers.Keywords: activity pattern, GPS collars, habitat selection, sumateran tiger, translocation

Ultrashort pulse laser machining of metals and alloys

Science.gov (United States)

Perry, Michael D.; Stuart, Brent C.

2003-09-16

The invention consists of a method for high precision machining (cutting, drilling, sculpting) of metals and alloys. By using pulses of a duration in the range of 10 femtoseconds to 100 picoseconds, extremely precise machining can be achieved with essentially no heat or shock affected zone. Because the pulses are so short, there is negligible thermal conduction beyond the region removed resulting in negligible thermal stress or shock to the material beyond approximately 0.1-1 micron (dependent upon the particular material) from the laser machined surface. Due to the short duration, the high intensity (>10.sup.12 W/cm.sup.2) associated with the interaction converts the material directly from the solid-state into an ionized plasma. Hydrodynamic expansion of the plasma eliminates the need for any ancillary techniques to remove material and produces extremely high quality machined surfaces with negligible redeposition either within the kerf or on the surface. Since there is negligible heating beyond the depth of material removed, the composition of the remaining material is unaffected by the laser machining process. This enables high precision machining of alloys and even pure metals with no change in grain structure.

Design and testing of a GPS/GSM collar prototype to combat cattle rustling

Directory of Open Access Journals (Sweden)

Francesco M. Tangorra

2013-10-01

Full Text Available Rustling is an age-old practice that was widespread in Italy until the first half of the 20th century. Today, incidents of cattle rustling are again being reported. However, the problem is not only found in Italy. It is also becoming a plague for ranchers in the US and is still rampant in East Africa. In Italy, the cattle rustling phenomena have usually been limited through the direct control of the herdsmen. Global positioning system (GPS and geographic information system (GIS combined technologies are increasingly applied for tracking and monitoring livestock with greater spatial and temporal resolution. However, so far, no case studies of the use of GPS technology to combat cattle rustling have been reported in the literature. The aim of this research was to develop a GPS/GSM (global system for mobile communication collar, using commercial hardware and implementing a specific software [ARVAshepherd 1.0; ARVAtec Srl, Rescaldina (MI, Italy] to track animals’ movements outside their grazing area and to signal when animals are straying outside virtual perimeters. A phase I study was conducted from January to June 2011 to build the GPS/GSM collar and to assess its performances in terms of GPS accuracy and precision, while a phase II study was conducted in July 2011 to test the GPS collar under real-life operating conditions. The static GPS positioning error achieved a circular error probable (50% and horizontal 95% accuracy of 1.462 m and 4.501 m, respectively. This is comparable with values obtained by other authors in static tests of a commercial GPS collar for grazing studies. In field tests, the system was able to identify the incorrect position of the cattle and the warning messages were sent promptly to the farmer, continuing until the animals had been repositioned inside the fence, thus highlighting the potential of the GPS/GSM collar as an anti-theft system.

Prophylactic treatment of flea-infested cats with an imidacloprid/flumethrin collar to forestall infection with Dipylidium caninum.

Science.gov (United States)

Fourie, Josephus J; Crafford, Dionne; Horak, Ivan G; Stanneck, Dorothee

2012-07-27

The objective of the study was to determine the sustained effectiveness of 10% imidacloprid (w/w) and 4.5% flumethrin (w/w) incorporated in a slow-release matrix collar in preventing Dipylidium caninum infection in cats following repeated laboratory-infestations with fleas infected with metacestodes. Efficacy against infection with D. caninum was evaluated by infesting 16 cats with the flea Ctenocephalides felis felis infected with metacestodes of the tapeworm. Medicated collars were fitted to 8 of the cats and infestation of each cat with 200 fleas from a suitably infected batch commenced 7 days later and continued at weekly intervals until Day 28. Efficacy against fleas was evaluated 24 h after each infestation. Infection of the cats with D. caninum was verified by daily examination of the cats' faeces and immediate surroundings for proglottids from Day 21 to Day 60. Calculation of the prophylactic effectiveness of the collars in preventing infection of the cats with D. caninum was based on the difference in the geometric mean number of scoleces recovered from the gastrointestinal tracts of collared compared to untreated cats at necropsy on Day 61. Efficacy of the collars against infestation of the cats with fleas was 99.9% on Day 7 and 100% at each subsequent weekly assessment. Infection of the fleas with metacestodes was ≥40% in 7 to 13 day old fleas, but progressively decreased thereafter. At necropsy all the control cats were infected with D. caninum and harboured between 19 and 346 scoleces with a geometric mean of 58.3. A single treated cat was infected and harboured 2 scoleces. Effective prevention of infection with D. caninum, based on a comparison of the geometric mean numbers of scoleces recovered from control and treated cats, was 99.7%. The insecticidal components of the medicated collars are capable of rapidly eliminating newly-acquired infestations of fleas that are infected with the metacestodes of D. caninum, thus preventing infection with the

Prophylactic treatment of flea-infested cats with an imidacloprid/flumethrin collar to forestall infection with Dipylidium caninum

Directory of Open Access Journals (Sweden)

Fourie Josephus J

2012-07-01

Full Text Available Abstract Background The objective of the study was to determine the sustained effectiveness of 10% imidacloprid (w/w and 4.5% flumethrin (w/w incorporated in a slow-release matrix collar in preventing Dipylidium caninum infection in cats following repeated laboratory-infestations with fleas infected with metacestodes. Methods Efficacy against infection with D. caninum was evaluated by infesting 16 cats with the flea Ctenocephalides felis felis infected with metacestodes of the tapeworm. Medicated collars were fitted to 8 of the cats and infestation of each cat with 200 fleas from a suitably infected batch commenced 7 days later and continued at weekly intervals until Day 28. Efficacy against fleas was evaluated 24 h after each infestation. Infection of the cats with D. caninum was verified by daily examination of the cats’ faeces and immediate surroundings for proglottids from Day 21 to Day 60. Calculation of the prophylactic effectiveness of the collars in preventing infection of the cats with D. caninum was based on the difference in the geometric mean number of scoleces recovered from the gastrointestinal tracts of collared compared to untreated cats at necropsy on Day 61. Results Efficacy of the collars against infestation of the cats with fleas was 99.9% on Day 7 and 100% at each subsequent weekly assessment. Infection of the fleas with metacestodes was ≥40% in 7 to 13 day old fleas, but progressively decreased thereafter. At necropsy all the control cats were infected with D. caninum and harboured between 19 and 346 scoleces with a geometric mean of 58.3. A single treated cat was infected and harboured 2 scoleces. Effective prevention of infection with D. caninum, based on a comparison of the geometric mean numbers of scoleces recovered from control and treated cats, was 99.7%. Conclusion The insecticidal components of the medicated collars are capable of rapidly eliminating newly-acquired infestations of fleas that are infected

Work Identity and Marital Adjustment in Blue-Collar Men.

Science.gov (United States)

Gaesser, David L.; Whitbourne, Susan Krauss

1985-01-01

Investigated the relationship between work-identity and satisfaction and marital adjustment in 40 married male blue-collar workers, ages 25 to 41 years. Satisfaction with extrinsic work factors related to marital adjustment, while satisfaction with intrinsic work factors negatively related to secondary role salience. Age negatively related to…

Neutron collar calibration for assay of LWR [light-water reactor] fuel assemblies

International Nuclear Information System (INIS)

Menlove, H.O.; Pieper, J.E.

1987-03-01

The neutron-coincidence collar is used for the verification of the uranium content in light-water reactor fuel assemblies. An AmLi neutron source is used to give an active interrogation of the fuel assembly to measure the 235 U content, and the 238 U content is verified from a passive neutron-coincidence measurement. This report gives the collar calibration data of pressurized-water reactor and boiling-water reactor fuel assemblies. Calibration curves and correction factors are presented for neutron absorbers (burnable poisons) and different fuel assembly sizes. The data were collected at Exxon Nuclear, Franco-Belge de Fabrication de Combustibles, ASEA-Atom, and other nuclear fuel fabrication facilities

The synergistic action of imidacloprid and flumethrin and their release kinetics from collars applied for ectoparasite control in dogs and cats

Directory of Open Access Journals (Sweden)

Stanneck Dorothee

2012-04-01

Full Text Available Abstract Background The control of tick and flea burdens in dogs and cats has become essential to the control of important and emerging vector borne diseases, some of which are zoonoses. Flea worry and flea bite hypersensitivity are additionally a significant disease entity in dogs and cats. Owner compliance in maintaining the pressure of control measures has been shown to be poor. For these reasons efforts are continuously being made to develop ectoparasiticides and application methods that are safe, effective and easy to apply for pet owners. A new polymer matrix collar has recently been developed which is registered for 8 months use in cats and dogs. The basic properties of this collar have been investigated in several in vitro and in vivo studies. Methods The effects of imidacloprid, flumethrin and the combination were evaluated in vitro by means of whole cell voltage clamp measurement experiments conducted on isolated neuron cells from Spodoptera frugiperda. The in vitro efficacy of the two compounds and the combination against three species of ticks and their life stages and fleas were evaluated in a dry surface glass vial assay. The kinetics of the compounds over time in the collar were evaluated by the change in mass of the collar and measurement of the surface concentrations and concentrations of the actives in the collar matrix by HPLC. Hair clipped from collar treated dogs and cats, collected at various time points, was used to assess the acaricidal efficacy of the actives ex vivo. Results An in vitro isolated insect nerve model demonstrated the synergistic neurotoxic effects of the pyrethroid flumethrin and the neonicotinoid imidacloprid. An in vitro glass vial efficacy and mortality study against various life stages of the ticks Ixodes ricinus, Rhipicephalus sanguineus and Dermacentor reticulatus and against the flea (Ctenocephalides felis demonstrated that the combination of these products was highly effective against these

The synergistic action of imidacloprid and flumethrin and their release kinetics from collars applied for ectoparasite control in dogs and cats

Science.gov (United States)

2012-01-01

Background The control of tick and flea burdens in dogs and cats has become essential to the control of important and emerging vector borne diseases, some of which are zoonoses. Flea worry and flea bite hypersensitivity are additionally a significant disease entity in dogs and cats. Owner compliance in maintaining the pressure of control measures has been shown to be poor. For these reasons efforts are continuously being made to develop ectoparasiticides and application methods that are safe, effective and easy to apply for pet owners. A new polymer matrix collar has recently been developed which is registered for 8 months use in cats and dogs. The basic properties of this collar have been investigated in several in vitro and in vivo studies. Methods The effects of imidacloprid, flumethrin and the combination were evaluated in vitro by means of whole cell voltage clamp measurement experiments conducted on isolated neuron cells from Spodoptera frugiperda. The in vitro efficacy of the two compounds and the combination against three species of ticks and their life stages and fleas were evaluated in a dry surface glass vial assay. The kinetics of the compounds over time in the collar were evaluated by the change in mass of the collar and measurement of the surface concentrations and concentrations of the actives in the collar matrix by HPLC. Hair clipped from collar treated dogs and cats, collected at various time points, was used to assess the acaricidal efficacy of the actives ex vivo. Results An in vitro isolated insect nerve model demonstrated the synergistic neurotoxic effects of the pyrethroid flumethrin and the neonicotinoid imidacloprid. An in vitro glass vial efficacy and mortality study against various life stages of the ticks Ixodes ricinus, Rhipicephalus sanguineus and Dermacentor reticulatus and against the flea (Ctenocephalides felis) demonstrated that the combination of these products was highly effective against these parasites. The release kinetics of

A nucleonic weighing machine

International Nuclear Information System (INIS)

Anon.

1978-01-01

The design and operation of a nucleonic weighing machine fabricated for continuous weighing of material over conveyor belt are described. The machine uses a 40 mCi cesium-137 line source and a 10 litre capacity ionization chamber. It is easy to maintain as there are no moving parts. It can also be easily removed and reinstalled. (M.G.B.)

Determination of locational error associated with global positioning system (GPS) radio collars in relation to vegetation and topography in north-central New Mexico

Energy Technology Data Exchange (ETDEWEB)

Bennett, K.; Biggs, J.; Fresquez, P.R.

1997-02-01

In 1996, a study was initiated to assess seasonal habitat use and movement patterns of Rocky Mountain elk (Cervus elaphus nelsoni) using global positioning system (GPS) radio collars. As part of this study, the authors attempted to assess the accuracies of GPS (non-differentially corrected) positions under various vegetation canopies and terrain conditions with the use of a GPS ``test`` collar. The test collar was activated every twenty minutes to obtain a position location and continuously uplinked to Argos satellites to transfer position data files. They used a Telonics, Inc. uplink receiver to intercept the transmission and view the results of the collar in real time. They placed the collar on a stand equivalent to the neck height of an adult elk and then placed the stand within three different treatment categories: (1) topographical influence (canyon and mesa tops), (2) canopy influence (open and closed canopy), and (3) vegetation type influence (ponderosa pine and pinion pine-juniper). The collar was kept at each location for one hour (usually obtaining three fixes). In addition, the authors used a hand-held GPS to obtain a position of the test collar at the same time and location.

Study on Gap Flow Field Simulation in Small Hole Machining of Ultrasonic Assisted EDM

Science.gov (United States)

Liu, Yu; Chang, Hao; Zhang, Wenchao; Ma, Fujian; Sha, Zhihua; Zhang, Shengfang

2017-12-01

When machining a small hole with high aspect ratio in EDM, it is hard for the flushing liquid entering the bottom gap and the debris could hardly be removed, which results in the accumulation of debris and affects the machining efficiency and machining accuracy. The assisted ultrasonic vibration can improve the removal of debris in the gap. Based on dynamics simulation software Fluent, a 3D model of debris movement in the gap flow field of EDM small hole machining assisted with side flushing and ultrasonic vibration is established in this paper. When depth to ratio is 3, the laws of different amplitudes and frequencies on debris distribution and removal are quantitatively analysed. The research results show that periodic ultrasonic vibration can promote the movement of debris, which is beneficial to the removal of debris in the machining gap. Compared to traditional small hole machining in EDM, the debris in the machining gap is greatly reduced, which ensures the stability of machining process and improves the machining efficiency.

Machinability of cast commercial titanium alloys.

Science.gov (United States)

Watanabe, I; Kiyosue, S; Ohkubo, C; Aoki, T; Okabe, T

2002-01-01

This study investigated the machinability of cast orthopedic titanium (metastable beta) alloys for possible application to dentistry and compared the results with those of cast CP Ti, Ti-6Al-4V, and Ti-6Al-7Nb, which are currently used in dentistry. Machinability was determined as the amount of metal removed with the use of an electric handpiece and a SiC abrasive wheel turning at four different rotational wheel speeds. The ratios of the amount of metal removed and the wheel volume loss (machining ratio) were also evaluated. Based on these two criteria, the two alpha + beta alloys tested generally exhibited better results for most of the wheel speeds compared to all the other metals tested. The machinability of the three beta alloys employed was similar or worse, depending on the speed of the wheel, compared to CP Ti. Copyright 2002 Wiley Periodicals, Inc.

Characterizing the Effects of Micro Electrical Discharge Machining Parameters on Material Removal Rate during Micro EDM Drilling of Tungsten Carbide (WC-Co)

Science.gov (United States)

Hourmand, Mehdi; Sarhan, Ahmed A. D.; Sayuti, Mohd

2017-10-01

Micro-dies, molds and miniaturized products can be manufactured using micro EDM process. In this research, EDM machine and on-machine fabricated CuW micro-electrode were utilized to produce the micro holes in WC-16%Co. The effects of voltage, current, pulse ON time, pulse OFF time, capacitor and rotating speed on Material removal rate (MRR) during micro EDM drilling of WC-16% Co was analyzed using fractional factorial design method. ANOVA analysis shows that increasing current, rotating speed, capacitor and decreasing voltage and pulse ON time lead to the amplify in MRR. It was found that out of all the factors, current and capacitor had the most significant effect on MRR, while the effect of capacitor was more than current. Eventually, it can be concluded that micro holes can be produced using EDM machine.

Electromechanical model of machine for vibroabrasive treatment of machine parts

OpenAIRE

Gorbatiyk, Ruslan; Palamarchuk, Igor; Chubyk, Roman

2015-01-01

A lot of operations on trimming clean and finishing – stripping up treatment, first of all, removing of burrs, rounding and processing of borders, until recently time was carried out by hand, and hardly exposed to automation and became a serious obstacle in subsequent growth of the labor productivity. Machines with free kinematics connection between a tool and the treating parts is provided by the printing-down of all of the surface of the machine parts, that allows us to effectively treat bo...

Ovarian folliculogenesis in collared peccary: Pecari tajacu (Artiodactyla: Tayassuidae

Directory of Open Access Journals (Sweden)

Diva Anelie Guimarães

2012-03-01

Full Text Available The sustainability and production of collared peccary (Pecari tajacu has been studied in the last few years; however, further information on its reproduction is necessary for breeding systems success. Understanding folliculogenesis aspects will contribute to effective reproductive biotechniques, which are useful in the preservation and production of wildlife. The aim of this study was to evaluate the ovarian folliculogenesis in collared peccary. Ovaries from six adult females of collared peccary were obtained through ovariectomy and analyzed. These were fixed in aqueous Bouin’s solution and sectioned into 7μm slices, stained with hematoxilin-eosin and analyzed by light microscopy. The number of pre-antral and antral follicles per ovary was estimated using the Fractionator Method. The follicles, oocytes and oocyte nuclei were measured using an ocular micrometer. Results showed that the length, width, thickness, weight, and the gross anatomy of the right and left ovaries were not significantly different. However, the mean number of corpora lutea was different between the phases of the estrous cycle (pLa sustentabilidad y la producción de pecarí de collar (Pecari tajacu han sido estudiados en los últimos años, sin embargo, más información sobre su reproducción es necesaria para el éxito de los sistemas de crianza . La comprensión de los aspectos relacionados con la foliculogénesis contribuirá con la aplicación de biotécnicas de reproducción, las cuales son útiles en la preservación y la producción de la vida silvestre. El objetivo de este estudio fue obtener datos sobre la población folicular del ovario de pecarí de collar. En relación con la población folicular en el ovario derecho, los valores de los folículos primordiales y primarios fueron similares, pero se observó que había una diferencia significativa (p<0.05 con el secundario. En el ovario izquierdo, la fase folicular presentó diferencias significativas (p<0

FORTY PLUS CLUBS AND WHITE-COLLAR MANHOOD DURING THE GREAT DEPRESSION

Directory of Open Access Journals (Sweden)

Gregory Wood

2008-01-01

Full Text Available As scholars of gender and labor have argued, chronic unemployment during the Great Depression precipitated a “crisis” of masculinity, compelling men to turn towards new industrial unions and the New Deal as ways to affirm work, breadwinning, and patriarchy as bases for manhood. But did all men experience this crisis? During the late 1930s, white-collar men organized groups called “Forty Plus Clubs” in response to their worries about joblessness and manhood. The clubs made it possible for unemployed executives to find new jobs, while at the same time recreating the male-dominated culture of the white-collar office. For male executives, Forty Plus Clubs precluded the Depression-era crisis of manhood, challenging the idea that the absence ofpaid employment was synonymous with the loss of masculinity.

Effect of machining parameters on surface integrity of silicon carbide ceramic using end electric discharge milling and mechanical grinding hybrid machining

International Nuclear Information System (INIS)

Ji, Renjie; Liu, Yonghong; Zhang, Yanzhen; Cai, Baoping; Li, Xiaopeng; Zheng, Chao

2013-01-01

A novel hybrid process that integrates end electric discharge (ED) milling and mechanical grinding is proposed. The process is able to effectively machine a large surface area on SiC ceramic with good surface quality and fine working environmental practice. The polarity, pulse on-time, and peak current are varied to explore their effects on the surface integrity, such as surface morphology, surface roughness, micro-cracks, and composition on the machined surface. The results show that positive tool polarity, short pulse on-time, and low peak current cause a fine surface finish. During the hybrid machining of SiC ceramic, the material is mainly removed by end ED milling at rough machining mode, whereas it is mainly removed by mechanical grinding at finish machining mode. Moreover, the material from the tool can transfer to the workpiece, and a combination reaction takes place during machining.

Why "Working Smarter" Isn't Working: White-Collar Productivity Improvement.

Science.gov (United States)

Shaw, Edward

2001-01-01

Discusses the productivity and work days of white collar workers. Topics include productivity improvement; task analysis; the amount of time spent reading, and how to reduce it by improving writing skills; time spent in meetings; empowered time management; and sustaining a climate for change. (LRW)

Refueling machine for a nuclear reactor

International Nuclear Information System (INIS)

Kowalski, E.F.; Hornak, L.P.; Swidwa, K.J.

1981-01-01

An improved refuelling machine for inserting and removing fuel assemblies from a nuclear reactor is described which has been designed to increase the reliability of such machines. The system incorporates features which enable the refuelling operation to be performed more efficiently and economically. (U.K.)

Design and development of remotely operated coolant channel cutting machine

International Nuclear Information System (INIS)

Suthar, R.L.; Sinha, A.K.; Srikrishnamurty, G.

1994-01-01

One of the coolant tubes of Narora Atomic Power Station (NAPS) reactor needs to be removed. To remove a coolant tube, four cutting operations, (liner tube cutting, end-fitting cutting, machining of seal weld of bellow ring and finally coolant tube cutting) are required to be carried out. A remotely operated cutting machine to carry out all these operations has been designed and developed by Central Workshops. This machine is able to cut at the exact location because of numerically controlled axial and radial travel of tool. Only by changing the tool head and tool holder, same machine can be used for various types of cutting/machining operations. This report details the design, manufacture, assembly and testing work done on the machine. (author). 4 figs

Dwell time adjustment for focused ion beam machining

International Nuclear Information System (INIS)

Taniguchi, Jun; Satake, Shin-ichi; Oosumi, Takaki; Fukushige, Akihisa; Kogo, Yasuo

2013-01-01

Focused ion beam (FIB) machining is potentially useful for micro/nano fabrication of hard brittle materials, because the removal method involves physical sputtering. Usually, micro/nano scale patterning of hard brittle materials is very difficult to achieve by mechanical polishing or dry etching. Furthermore, in most reported examples, FIB machining has been applied to silicon substrates in a limited range of shapes. Therefore, a versatile method for FIB machining is required. We previously established the dwell time adjustment for mechanical polishing. The dwell time adjustment is calculated by using a convolution model derived from Preston’s hypothesis. More specifically, the target removal shape is a convolution of the unit removal shape, and the dwell time is calculated by means of one of four algorithms. We investigate these algorithms for dwell time adjustment in FIB machining, and we found that a combination a fast Fourier transform calculation technique and a constraint-type calculation is suitable. By applying this algorithm, we succeeded in machining a spherical lens shape with a diameter of 2.93 μm and a depth of 203 nm in a glassy carbon substrate by means of FIB with dwell time adjustment

Description and performance characteristics for the neutron Coincidence Collar for the verification of reactor fuel assemblies

International Nuclear Information System (INIS)

Menlove, H.O.

1981-08-01

An active neutron interrogation method has been developed for the measurement of 235 U content in fresh fuel assemblies. The neutron Coincidence Collar uses neutron interrogation with an AmLi neutron source and coincidence counting the induced fission reaction neutrons from the 235 U. This manual describes the system components, operation, and performance characteristics. Applications of the Coincidence Collar to PWR and BWR types of reactor fuel assemblies are described

Ultrasonic Abrasive Removal Of EDM Recast

Science.gov (United States)

Mandel, Johnny L.; Jacobson, Marlowe S.

1990-01-01

Ultrasonic abrasive process removes layer of recast material generated during electrical-discharge machining (EDM) of damper pocket on turbine blade. Form-fitted tool vibrated ultrasonically in damper pocket from which material removed. Vibrations activate abrasive in pocket. Amount of material removed controlled precisely.

Physical activity, job demand-control, perceived stress-energy, and salivary cortisol in white-collar workers

DEFF Research Database (Denmark)

Hansen, Åse Marie; Blangsted, Anne Katrine; Hansen, Ernst Albin

2010-01-01

The aim of the present study is to examine the association between physical activity and perceived job demand, job control, perceived stress and energy, and physiological arousal reflected by morning and evening concentrations of cortisol in saliva among white-collar workers.......The aim of the present study is to examine the association between physical activity and perceived job demand, job control, perceived stress and energy, and physiological arousal reflected by morning and evening concentrations of cortisol in saliva among white-collar workers....

Hypospadias repair with the glanular-frenular collar (GFC) technique.

Science.gov (United States)

Özbey, Hüseyin; Etker, Şeref

2017-02-01

In the normal human penis, the glans wings merge in the midline ventrally, but are separated by the 'septum glandis' in conjunction with the frenulum. The frenulum is also included in the formation of the distal (glanular and subcoronal) urethra, which has a special part known as the 'fossa navicularis'. This has inspired a hypospadias repair technique that simulates the development of the glanular and subcoronal urethra, which can be incorporated into the repair of all cases of hypospadias. A total of 121 patients with varying degrees of hypospadias underwent surgery with the described technique: a Y-V plasty was used to dissect the inner foreskin, in a fashion that allowed for its ventral mobilization as a frenular mucosal collar. After tubularization of the proximal urethra, a partial spongioplasty was performed that extended up to the subcoronal level. The glans wings were approximated only at their outermost convexities, with a couple of subepithelial sutures, leaving a slit for the meatus. The cleft-like area between the split wings of the glans penis was filled with the terminal ends of the spongiosum and the dartos of the mucosal collar, which converged to form a septum and a neo-frenulum (glanular-frenular collar, GFC). The midline skin closure of the ventral collar and the circumferential foreskin closure was completed as usual. At a mean follow-up of 10 months, two patients developed urethral fistula (2%), six had meatal stenosis (5%), and two had glans dehiscence (2%) that resulted in meatal retraction. Overall, patients had a cosmetically satisfying appearance (Figure). Forty-one received secondary circumcision; the parents of 80 (66%) patients were satisfied with the final foreskin appearance obtained with this method. The split wings of the glans penis or so-called ventral cleft between the glans wings that accommodate the frenulum is part of normal anatomy. Hence, in hypospadias surgery, the approximated glans wings should allow for ventral support

Ultraprecision machining. Cho seimitsu kako

Energy Technology Data Exchange (ETDEWEB)

Suga, T [The Univ. of Tokyo, Tokyo (Japan). Research Center for Advanced Science and Technology

1992-10-05

It is said that the image of ultraprecision improved from 0.1[mu]m to 0.01[mu]m within recent years. Ultraprecision machining is a production technology which forms what is called nanotechnology with ultraprecision measuring and ultraprecision control. Accuracy means average machined sizes close to a required value, namely the deflection errors are small; precision means the scattered errors of machined sizes agree very closely. The errors of machining are related to both of the above errors and ultraprecision means the combined errors are very small. In the present ultraprecision machining, the relative precision to the size of a machined object is said to be in the order of 10[sup -6]. The flatness of silicon wafers is usually less than 0.5[mu]m. It is the fact that the appearance of atomic scale machining is awaited as the limit of ultraprecision machining. The machining of removing and adding atomic units using scanning probe microscopes are expected to reach the limit actually. 2 refs.

White-collar workers' hemodynamic responses during working hours.

Science.gov (United States)

Liu, Xinxin; Iwakiri, Kazuyuki; Sotoyama, Midori

2017-08-08

In the present study, two investigations were conducted at a communication center, to examine white-collar workers' hemodynamic responses during working hours. In investigation I, hemodynamic responses were measured on a working day; and in investigation II, cardiovascular responses were verified on both working and non-working days. In investigation I, blood pressure, cardiac output, heart rate, stroke volume, and total peripheral resistance were measured in 15 workers during working hours (from 9:00 am to 18:00 pm) on one working day. Another 40 workers from the same workplace participated in investigation II, in which blood pressure and heart rate were measured between the time workers arose in the morning until they went to bed on 5 working days and 2 non-working days. The results showed that blood pressure increased and remained at the same level during working hours. The underlying hemodynamics of maintaining blood pressure, however, changed between the morning and the afternoon on working days. Cardiac responses increased in the afternoon, suggesting that cardiac burdens increase in the afternoon on working days. The present study suggested that taking underlying hemodynamic response into consideration is important for managing the work-related cardiovascular burden of white-collar workers.

Theory and practice in machining systems

CERN Document Server

Ito, Yoshimi

2017-01-01

This book describes machining technology from a wider perspective by considering it within the machining space. Machining technology is one of the metal removal activities that occur at the machining point within the machining space. The machining space consists of structural configuration entities, e.g., the main spindle, the turret head and attachments such the chuck and mandrel, and also the form-generating movement of the machine tool itself. The book describes fundamental topics, including the form-generating movement of the machine tool and the important roles of the attachments, before moving on to consider the supply of raw materials into the machining space, and the discharge of swarf from it, and then machining technology itself. Building on the latest research findings “Theory and Practice in Machining System” discusses current challenges in machining. Thus, with the inclusion of introductory and advanced topics, the book can be used as a guide and survey of machining technology for students an...

Effect of machining fluid on the process performance of wire electrical discharge machining of nanocomposite ceramic

Directory of Open Access Journals (Sweden)

Zhang Chengmao

2015-01-01

Full Text Available Wire electric discharge machining (WEDM promise to be effective and economical techniques for the production of tools and parts from conducting ceramic blanks. However, the manufacturing of nanocomposite ceramics blanks with these processes is a long and costly process. This paper presents a new process of machining nanocomposite ceramics using WEDM. WEDM uses water based emulsion, polyvinyl alcohol and distilled water as the machining fluid. Machining fluid is a primary factor that affects the material removal rate and surface quality of WEDM. The effects of emulsion concentration, polyvinyl alcohol concentration and distilled water of the machining fluid on the process performance have been investigated.

Does Shoe Collar Height Influence Ankle Joint Kinematics and Kinetics in Sagittal Plane Maneuvers?

Directory of Open Access Journals (Sweden)

Yang Yang, Ying Fang, Xini Zhang, Junliang He, Weijie Fu

2017-12-01

Full Text Available The Objective of the study is to investigate the effects of basketball shoes with different collar heights on ankle kinematics and kinetics and athletic performance in different sagittal plane maneuvers. Twelve participants who wore high-top and low-top basketball shoes (hereafter, HS and LS, respectively performed a weight-bearing dorsiflexion (WB-DF maneuver, drop jumps (DJs, and lay-up jumps (LJs. Their sagittal plane kinematics and ground reaction forces were recorded using the Vicon motion capture system and Kistler force plates simultaneously. Moreover, ankle dorsiflexion and plantarflexion angles, moment, power, stiffness, and jump height were calculated. In the WB-DF test, the peak ankle dorsiflexion angle (p = 0.041 was significantly smaller in HS than in LS. Additionally, the peak ankle plantarflexion moment (p = 0.028 and power (p = 0.022 were significantly lower in HS than in LS during LJs but not during DJs. In both jumping maneuvers, no significant differences were found in the jump height or ankle kinematics between the two shoe types. According to the WB-DF test, increasing shoe collar height can effectively reduce the ankle range of motion in the sagittal plane. Although the HS did not restrict the flexion–extension performance of the ankle joint during two jumping maneuvers, an increased shoe collar height can reduce peak ankle plantarflexion moment and peak power during the push-off phase in LJs. Therefore, a higher shoe collar height should be used to circumvent effects on the partial kinetics of the ankle joint in the sagittal plane.

Effect of psychosocial factors on metabolic syndrome in male and female blue-collar workers.

Science.gov (United States)

Hwang, Won Ju; Lee, Chung Yul

2014-01-01

The purposes of this study were to examine the relationship between psychosocial factors and metabolic syndrome among male and female blue-collar workers, and which factors influence their metabolic syndrome by sex. A cross-sectional study was completed of 154 men and 80 women working at small companies in Korea. The data were collected through a structured questionnaire, blood test, and anthropometric and blood pressure measure. Metabolic syndrome was diagnosed from the results of blood test and the measurements of waist circumference and blood pressure. The prevalence of metabolic syndrome among male and female blue-collar workers was 24.0% and 7.5%, respectively. Multiple logistic regression analysis was performed to examine factors of metabolic syndrome associated with sex. After controlling for age, marital status, smoking, alcohol drinking, shift work, overtime work, and physical exercise, job stress (odds ratio [OR] = 3.10, P = 0.005) and risk perception (OR = 1.12, P = 0.016) were influencing factors for men, and low job stress (OR = 0.05, P = 0.04), low social support (OR = 1.51, P = 0.009), and risk perception (OR = 1.27, P = 0.023) for women. Metabolic syndrome among blue-collar workers is closely related to psychosocial factors, such as job stress, social support, and risk perception, with the effect of job stress a point of difference between men and women. Occupational health nurses should be cognizant of the importance of assessing the effect of psychosocial factors on cardiovascular risk for blue-collar workers. © 2012 The Authors. Japan Journal of Nursing Science © 2012 Japan Academy of Nursing Science.

Does Shoe Collar Height Influence Ankle Joint Kinematics and Kinetics in Sagittal Plane Maneuvers?

Science.gov (United States)

Yang, Yang; Fang, Ying; Zhang, Xini; He, Junliang; Fu, Weijie

2017-12-01

The Objective of the study is to investigate the effects of basketball shoes with different collar heights on ankle kinematics and kinetics and athletic performance in different sagittal plane maneuvers. Twelve participants who wore high-top and low-top basketball shoes (hereafter, HS and LS, respectively) performed a weight-bearing dorsiflexion (WB-DF) maneuver, drop jumps (DJs), and lay-up jumps (LJs). Their sagittal plane kinematics and ground reaction forces were recorded using the Vicon motion capture system and Kistler force plates simultaneously. Moreover, ankle dorsiflexion and plantarflexion angles, moment, power, stiffness, and jump height were calculated. In the WB-DF test, the peak ankle dorsiflexion angle (p = 0.041) was significantly smaller in HS than in LS. Additionally, the peak ankle plantarflexion moment (p = 0.028) and power (p = 0.022) were significantly lower in HS than in LS during LJs but not during DJs. In both jumping maneuvers, no significant differences were found in the jump height or ankle kinematics between the two shoe types. According to the WB-DF test, increasing shoe collar height can effectively reduce the ankle range of motion in the sagittal plane. Although the HS did not restrict the flexion-extension performance of the ankle joint during two jumping maneuvers, an increased shoe collar height can reduce peak ankle plantarflexion moment and peak power during the push-off phase in LJs. Therefore, a higher shoe collar height should be used to circumvent effects on the partial kinetics of the ankle joint in the sagittal plane.

Different parts, different stories: climate sensitivity of growth is stronger in root collars vs. stems in tundra shrubs.

Science.gov (United States)

Ropars, Pascale; Angers-Blondin, Sandra; Gagnon, Marianne; Myers-Smith, Isla H; Lévesque, Esther; Boudreau, Stéphane

2017-08-01

Shrub densification has been widely reported across the circumpolar arctic and subarctic biomes in recent years. Long-term analyses based on dendrochronological techniques applied to shrubs have linked this phenomenon to climate change. However, the multi-stemmed structure of shrubs makes them difficult to sample and therefore leads to non-uniform sampling protocols among shrub ecologists, who will favor either root collars or stems to conduct dendrochronological analyses. Through a comparative study of the use of root collars and stems of Betula glandulosa, a common North American shrub species, we evaluated the relative sensitivity of each plant part to climate variables and assessed whether this sensitivity is consistent across three different types of environments in northwestern Québec, Canada (terrace, hilltop and snowbed). We found that root collars had greater sensitivity to climate than stems and that these differences were maintained across the three types of environments. Growth at the root collar was best explained by spring precipitation and summer temperature, whereas stem growth showed weak and inconsistent responses to climate variables. Moreover, sensitivity to climate was not consistent among plant parts, as individuals having climate-sensitive root collars did not tend to have climate-sensitive stems. These differences in sensitivity of shrub parts to climate highlight the complexity of resource allocation in multi-stemmed plants. Whereas stem initiation and growth are driven by microenvironmental variables such as light availability and competition, root collars integrate the growth of all plant parts instead, rendering them less affected by mechanisms such as competition and more responsive to signals of global change. Although further investigations are required to determine the degree to which these findings are generalizable across the tundra biome, our results indicate that consistency and caution in the choice of plant parts are a key

The role of the State Audit Institution in prevention of white-collar crime in the public sector

Directory of Open Access Journals (Sweden)

Šuput Jelena

2014-01-01

Full Text Available In this paper, the author points out to the important role of the Serbian State Audit Institution in prevention of corruptive practices, felonies and white-collar crime in the public sector in the Republic of Serbia. Although the activity of supreme state auditors is not primarily aimed at detecting criminal offences in the public sector, their efforts and results in this area are by no means insignificant. This is due to the fact that state auditors are well-trained to interpret and apply the legal provisions from the area of public finance, public procurements and accountancy, regulating the budget system of revenues and expenditures whose violation may constitute a criminal offence within the scope of white-collar crime. Considering the fact that it is an independent and autonomous state authority, the Serbian Supreme Audit Institution should play a very important role in reducing 'the dark figures of white-collar crime'. In many cases, the fear of crime detection as well as the fear of being punished are sufficient to exert the preventive effect on the potential perpetrators of white-collar crimes. However, we have to bear in mind that the prevention of corruption and other felonies which are qualified as white-collar crime calls for a joint effort of all state institutions and citizens alike. Another fact which is very important for improving the operative quality of the Supreme Audit Institution is its membership in the International Organisation of Supreme Audit Institutions and cooperation with the Supreme Audit Institutions in other countries.

Fire protection in Angra-2 nuclear power plant. The use of fire protection collars on plastic piping systems

International Nuclear Information System (INIS)

Oliveira Segabinaze, R. de

1994-01-01

The object of this paper is to briefly the use of fire protection collars on plastic piping systems passing through wall and floor penetration. The fire protection collars consist of a stainless steel housing, in which the leading edges of two pivoting plates are in constant pressure contact with the pipe. In case of fire these plates react on the softened pipe with a guillotine action, thereby stopping the flow; within the housing a foam material expands to fill the space when subject to the heat of the fire. The piping project has to be modified to permit the fixing of the collars to walls and floor penetrations. (author). 2 refs, 9 figs

Increased lung function decline in blue-collar workers exposed to welding fumes.

Science.gov (United States)

Thaon, Isabelle; Demange, Valérie; Herin, Fabrice; Touranchet, Annie; Paris, Christophe

2012-07-01

There is no consensus at the present time about the effect of welding on lung function decline. This study compared lung function decline between blue-collar workers exposed and not exposed to welding fumes in a French longitudinal cohort of 21,238 subjects aged 37 to 52 years at inclusion. Medical data, occupation, sector of activity, and spirometry were recorded twice by occupational physicians in 1990 and 1995. A job-exposure matrix was used to identify 503 male blue-collar workers exposed to welding fumes and 709 control subjects and to define the weekly duration of exposure to welding fumes. Baseline lung function parameters were higher in workers exposed to welding fumes than in control subjects. After a 5-year follow-up, welding-fume exposure was associated with a nonsignificant decline in FVC (P = .06) and FEV(1) (P = .07) after adjustment for age, pack-years, BMI, and baseline value of the parameter. A significant accelerated decline in FEV(1) (P = .046) was also observed in never smokers exposed to welding fumes. An “exposure-response” relationship was observed between FEV(1) decline and weekly duration of exposure to welding fumes in nonsmokers but not in smokers. Blue-collar workers exposed to welding fumes showed accelerated decline in lung function, which, in nonsmokers, was related to weekly duration of exposure.

Collimating device for x-rays

International Nuclear Information System (INIS)

Schroeder, C.H.

1978-01-01

A position indicating device which attaches to an X-ray machine is provided with a collar onto which a lead lined cylinder may be threaded. The cylinder has an end plate through which a rectangular opening is formed in order to provide a rectangular X-ray beam for use in cephalometric radiography. When the cylinder is removed, a circular beam is emitted for use in intra-oral radiography

Machining refractory alloys: an overview

International Nuclear Information System (INIS)

Christopher, J.D.

1984-01-01

Nontraditional machining is a generic term for those material removal processes that differ drastically from the historic operations such as turning, milling, drilling, tapping, and grinding. The use of primary energy modes other than mechanical, such as thermal, electrical, and chemical, sets these operations apart and reinforces their nontraditional label. Several of these newer processes have been very successful in machining close tolerance parts from refractory materials. This paper provides a general overview of both traditional and nontraditional aspects of machining refractory materials. 11 figures, 7 tables

Job demands and health complaints in white and blue collar workers

NARCIS (Netherlands)

Schreuder, K. J.; Roelen, C. A. M.; Koopmans, P. C.; Groothoff, J. W.

2008-01-01

Background: General health in the working population is thought to depend on working conditions. Objective: This survey studied job demands and health complaints in working white and blue collar employees. We expect physical and psychological job demands to be differentially distributed among white

High-speed micro-electro-discharge machining.

Energy Technology Data Exchange (ETDEWEB)

Chandrasekar, Srinivasan Dr. (.School of Industrial Engineering, West Lafayette, IN); Moylan, Shawn P. (School of Industrial Engineering, West Lafayette, IN); Benavides, Gilbert Lawrence

2005-09-01

When two electrodes are in close proximity in a dielectric liquid, application of a voltage pulse can produce a spark discharge between them, resulting in a small amount of material removal from both electrodes. Pulsed application of the voltage at discharge energies in the range of micro-Joules results in the continuous material removal process known as micro-electro-discharge machining (micro-EDM). Spark erosion by micro-EDM provides significant opportunities for producing small features and micro-components such as nozzle holes, slots, shafts and gears in virtually any conductive material. If the speed and precision of micro-EDM processes can be significantly enhanced, then they have the potential to be used for a wide variety of micro-machining applications including fabrication of microelectromechanical system (MEMS) components. Toward this end, a better understanding of the impacts the various machining parameters have on material removal has been established through a single discharge study of micro-EDM and a parametric study of small hole making by micro-EDM. The main avenues for improving the speed and efficiency of the micro-EDM process are in the areas of more controlled pulse generation in the power supply and more controlled positioning of the tool electrode during the machining process. Further investigation of the micro-EDM process in three dimensions leads to important design rules, specifically the smallest feature size attainable by the process.

Biomechanical effects of two different collar implant structures on stress distribution under cantilever fixed partial dentures.

Science.gov (United States)

Merıç, Gökçe; Erkmen, Erkan; Kurt, Ahmet; Eser, Atilim; özden, Ahmet Utku

2011-11-01

The purpose of the study was to compare the effects of two distinct collar geometries of implants on stress distribution in the bone around the implants supporting cantilever fixed partial dentures (CFPDs) as well as in the implant-abutment complex and superstructures. The three-dimensional finite element method was selected to evaluate the stress distribution. CFPDs which was supported by microthread collar structured (MCS) and non-microthread collar structured (NMCS) implants was modeled; 300 N vertical, 150 N oblique and 60 N horizontal forces were applied to the models separately. The stress values in the bone, implant-abutment complex and superstructures were calculated. In the MCS model, higher stresses were located in the cortical bone and implant-abutment complex in the case of vertical load while decreased stresses in cortical bone and implant-abutment complex were noted within horizontal and oblique loading. In the case of vertical load, decreased stresses have been noted in cancellous bone and framework. Upon horizontal and oblique loading, a MCS model had higher stress in cancellous bone and framework than the NMCS model. Higher von Mises stresses have been noted in veneering material for NMCS models. It has been concluded that stress distribution in implant-supported CFPDs correlated with the macro design of the implant collar and the direction of applied force.

The effect on patency of type, shape and volume of a vein collar used at the distal anastomis of PTFE-bypass to arteries below-knee

DEFF Research Database (Denmark)

Lundgren, F; Schroeder, Torben Veith

2012-01-01

The aim of this paper was to study the effect on patency rate of different types of vein collar (Miller's original or St Mary's boot), different length/height shapes of vein collar, and different vein collar volumes at the distal anastomosis of PTFE-bypass grafts to below-knee arteries in patients...

Informing Tobacco Cessation Benefit Use Interventions for Unionized Blue-Collar Workers: A Mixed-Methods Reasoned Action Approach.

Science.gov (United States)

Yzer, Marco; Weisman, Susan; Mejia, Nicole; Hennrikus, Deborah; Choi, Kelvin; DeSimone, Susan

2015-08-01

Blue-collar workers typically have high rates of tobacco use but low rates of using tobacco cessation resources available through their health benefits. Interventions to motivate blue-collar tobacco users to use effective cessation support are needed. Reasoned action theory is useful in this regard as it can identify the beliefs that shape tobacco cessation benefit use intentions. However, conventional reasoned action research cannot speak to how those beliefs can best be translated into intervention messages. In the present work, we expand the reasoned action approach by adding additional qualitative inquiry to better understand blue-collar smokers' beliefs about cessation benefit use. Across three samples of unionized blue-collar tobacco users, we identified (1) the 35 attitudinal, normative, and control beliefs that represented tobacco users' belief structure about cessation benefit use; (2) instrumental attitude as most important in explaining cessation intention; (3) attitudinal beliefs about treatment options' efficacy, health effects, and monetary implications of using benefits as candidates for message design; (4) multiple interpretations of cessation beliefs (e.g., short and long-term health effects); and (5) clear implications of these interpretations for creative message design. Taken together, the findings demonstrate how a mixed-method reasoned action approach can inform interventions that promote the use of tobacco cessation health benefits.

Remote filter handling machine for Sizewell B

International Nuclear Information System (INIS)

Barker, D.

1993-01-01

Two Filter Handling machines (FHM) have been supplied to Nuclear Electric plc for use at Sizewell B Power Station. These machines have been designed and built following ALARP principles with the functional objective being to remove radioactive filter cartridges from a filter housing and replace them with clean filter cartridges. Operation of the machine is achieved by the prompt of each distinct task via an industrial computer or the prompt of a full cycle using the automatic mode. The design of the machine features many aspects demonstrating ALARP while keeping the machine simple, robust and easy to maintain. (author)

Prevention of White-Collar Crime by Knowledge and Learning in Business Organizations: An Empirical Study of Chief Financial Officer Management

Directory of Open Access Journals (Sweden)

Hans Solli-Soether

2012-01-01

Full Text Available Knowledge and learning are important in combating financial crime generallyand white-collar crime in particular. The purpose of this research is to generateinsights into prevention approaches in practice that may reflect on acontingent approach. The five hundred largest business companies in termsof annual turnover were identified in Norway for our empirical study of whitecollarcrime. A paper letter was mailed to the chief financial officer (CFOasking him or her to fill in the questionnaire to be found on a web site usinga password found in the letter. The open-ended question in the questionnaireto CFOs about prevention of white-collar crime was formulated as follows:How can white-collar crime best be prevented in your company? Survey resultsindicate an even distribution of respondents emphasizing control and respondentsemphasizing influence. This empirical research steps back from manybest practice articles and provides insights into preferences of chief financialofficers on how to prevent white-collar crime in the company.

Comparison of risk factors for tooth loss between professional drivers and white-collar workers: an internet survey

OpenAIRE

SUZUKI, Seitaro; YOSHINO, Koichi; TAKAYANAGI, Atsushi; ISHIZUKA, Yoichi; SATOU, Ryouichi; KAMIJO, Hideyuki; SUGIHARA, Naoki

2015-01-01

This cross-sectional study was conducted to examine tooth loss and associated factors among professional drivers and white-collar workers. The participants were recruited by applying screening procedures to a pool of Japanese registrants in an online database. The participants were asked to complete a self-reported questionnaire. A total of 592 professional drivers and 328 white-collar workers (male, aged 30 to 69 years) were analyzed. A multiple logistic regression analysis was performed to ...

Electrochemical machining - manufacturing of turbine and reactor components

International Nuclear Information System (INIS)

Otto, K.

1987-01-01

Electrochemical machining is a shaping process for metallic workpieces with complex geometries. Using an electrode corresponding to the negative of the desired shape, the material to be removed is dissolved anodically at erosion rates of up to 10 mm/min. The reproducible shape accuracy lies between 0,02 and 0,08 mm, depending on the machining problem. Surface finishes of less than 18 μm are attained. The hardness of the material has no influence on the metal removal process. The workpiece is not subjected to any thermal stressing during machining. The process is well suited for quantity production of complex parts and is used inter alia for turbine blades and components for nuclear reactors. (orig.) [de

Nontraditional machining processes research advances

CERN Document Server

2013-01-01

Nontraditional machining employs processes that remove material by various methods involving thermal, electrical, chemical and mechanical energy or even combinations of these. Nontraditional Machining Processes covers recent research and development in techniques and processes which focus on achieving high accuracies and good surface finishes, parts machined without burrs or residual stresses especially with materials that cannot be machined by conventional methods. With applications to the automotive, aircraft and mould and die industries, Nontraditional Machining Processes explores different aspects and processes through dedicated chapters. The seven chapters explore recent research into a range of topics including laser assisted manufacturing, abrasive water jet milling and hybrid processes. Students and researchers will find the practical examples and new processes useful for both reference and for developing further processes. Industry professionals and materials engineers will also find Nontraditional M...

Prophylactic treatment of flea-infested dogs with an imidacloprid / flumethrin collar (Seresto®, Bayer) to preempt infection with Dipylidium caninum.

Science.gov (United States)

Fourie, Josephus J; Crafford, Dionne; Horak, Ivan G; Stanneck, Dorothee

2013-08-01

The objective of the study was to determine the sustained effectiveness of 10 % imidacloprid and 4.5 % flumethrin, incorporated in a slow-release matrix collar, in preventing Dipylidium caninum infection in dogs after repeated laboratory infestations with fleas infected with metacestodes of this tapeworm. Efficacy against infection with D. caninum was evaluated by infesting 16 dogs with cat fleas (Ctenocephalides felis) on study days 7, 14, 21, 28, 35 and 42, from batches suitably infected with D. caninum metacestodes. Prior to each post-treatment infestation the D. caninum infection rate for the fleas was determined by microscopically examining 100 fleas for D. caninum metacestodes. The D. caninum prevalence in the fleas used for infestations ranged from 23 % to 52 %. Medicated collars were fitted to 8 of the dogs on study day 0. The weight of the IVP collars varied between 35.48 g and 38.48 g (average 37.16 g), whilst animal weight varied between 12.20 kg and 17.98 kg (treated group, n = 8, average 14.79 kg). Seven days later infestation of each of the 16 dogs with 250 fleas commenced. Infestations continued at weekly intervals until Day 42 with efficacy against fleas evaluated 24 hours after each infestation. From Days 21 to 74, infection of the dogs with D. caninum was verified (daily examination of faeces and cages for the presence of expelled proglottids). Calculation of prophylactic effectiveness of the collars in preventing infection with D. caninum was based on the difference in geometric mean numbers of scoleces between groups at necropsy on Day 75. Effective prevention of infection with D. caninum was found to be 96.6 %. Efficacy of the collars against fleas was ≥ 99.9 % for the duration of the assessment period. Newly acquired infestations of fleas are rapidly eliminated by the insecticidal components of the medicated collars over a period of several months. In the event of fleas being infected with metacestodes, with D. caninum can be prevented in

Rotary Ultrasonic Machining of Poly-Crystalline Cubic Boron Nitride

Directory of Open Access Journals (Sweden)

Kuruc Marcel

2014-12-01

Full Text Available Poly-crystalline cubic boron nitride (PCBN is one of the hardest material. Generally, so hard materials could not be machined by conventional machining methods. Therefore, for this purpose, advanced machining methods have been designed. Rotary ultrasonic machining (RUM is included among them. RUM is based on abrasive removing mechanism of ultrasonic vibrating diamond particles, which are bonded on active part of rotating tool. It is suitable especially for machining hard and brittle materials (such as glass and ceramics. This contribution investigates this advanced machining method during machining of PCBN.

Machinability of nickel based alloys using electrical discharge machining process

Science.gov (United States)

Khan, M. Adam; Gokul, A. K.; Bharani Dharan, M. P.; Jeevakarthikeyan, R. V. S.; Uthayakumar, M.; Thirumalai Kumaran, S.; Duraiselvam, M.

2018-04-01

The high temperature materials such as nickel based alloys and austenitic steel are frequently used for manufacturing critical aero engine turbine components. Literature on conventional and unconventional machining of steel materials is abundant over the past three decades. However the machining studies on superalloy is still a challenging task due to its inherent property and quality. Thus this material is difficult to be cut in conventional processes. Study on unconventional machining process for nickel alloys is focused in this proposed research. Inconel718 and Monel 400 are the two different candidate materials used for electrical discharge machining (EDM) process. Investigation is to prepare a blind hole using copper electrode of 6mm diameter. Electrical parameters are varied to produce plasma spark for diffusion process and machining time is made constant to calculate the experimental results of both the material. Influence of process parameters on tool wear mechanism and material removal are considered from the proposed experimental design. While machining the tool has prone to discharge more materials due to production of high energy plasma spark and eddy current effect. The surface morphology of the machined surface were observed with high resolution FE SEM. Fused electrode found to be a spherical structure over the machined surface as clumps. Surface roughness were also measured with surface profile using profilometer. It is confirmed that there is no deviation and precise roundness of drilling is maintained.

Characteristics of laser assisted machining for silicon nitride ceramic according to machining parameters

International Nuclear Information System (INIS)

Kim, Jong Do; Lee, Su Jin; Suh, Jeong

2011-01-01

This paper describes the Laser Assisted Machining (LAM) that cuts and removes softened parts by locally heating the ceramic with laser. Silicon nitride ceramics can be machined with general machining tools as well, because YSiAlON, which was made up ceramics, is soften at about 1,000 .deg. C. In particular, the laser, which concentrates on highly dense energy, can locally heat materials and very effectively control the temperature of the heated part of specimen. Therefore, this paper intends to propose an efficient machining method of ceramic by deducing the machining governing factors of laser assisted machining and understanding its mechanism. While laser power is the machining factor that controls the temperature, the CBN cutting tool could cut the material more easily as the material gets deteriorated from the temperature increase by increasing the laser power, but excessive oxidation can negatively affect the quality of the material surface after machining. As the feed rate and cutting depth increase, the cutting force increases and tool lifespan decreases, but surface oxidation also decreases. In this experiment, the material can be cut to 3 mm of cutting depth. And based on the results of the experiment, the laser assisted machining mechanism is clarified

Effect of Electric Discharge Machining on Material Removal Rate and White Layer Composition

Directory of Open Access Journals (Sweden)

SHAHID MEHMOOD

2017-01-01

Full Text Available In this study the MRR (Material Removal Rate of the aerospace grade (2024 T6 aluminum alloy 2024 T6 has been determined with copper electrode and kerosene oil is used as dielectric liquid. Discharge energy is controlled by electric current while keeping Pulse-ON time and Pulse-OFF time as constant. The characteristics of the EDMed (Electric Discharge Machined surface are discussed. The sub-surface defect due to arcing has been explained. As the surface material of tool electrode and workpiece melts simultaneously and there are chances of the contamination of both surfaces by the contents of each other. Therefore, the EDS (Energy Dispersive Spectroscopy of the white layer and base material of the workpiece was performed by SEM (Scanning Electron Microscope at the discharge currents of 3, 6 and 12 amperes. It was conformed that the contamination of the surface of the workpiece material occurred by carbon, copper and oxygen contents. The quantitative analysis of these contents with respect to the discharge current has been presented in this paper.

Laser machining micro-structures on diamond surface with a sub-nanosecond pulsed laser

Science.gov (United States)

Wu, Mingtao; Guo, Bing; Zhao, Qingliang

2018-02-01

Micro-structure surface on diamond material is widely used in a series of industrial and scientific applications, such as micro-electromechanical systems (MEMS), nanoelectromechanical systems (NEMS), microelectronics, textured or micro-structured diamond machining tools. The efficient machining of micro-structure on diamond surface is urgently demanded in engineering. In this paper, laser machining square micro-structure on diamond surface was studied with a sub-nanosecond pulsed laser. The influences of laser machining parameters, including the laser power, scanning speed, defocusing quantity and scanning pitch, were researched in view of the ablation depth, material removal rate and machined surface topography. Both the ablation depth and material removal rate increased with average laser power. A reduction of the growth rate of the two parameters was induced by the absorption of the laser plasma plume at high laser power. The ablation depth non-linearly decreased with the increasing of the scanning speed while the material removal rate showed an opposite tendency. The increasing of the defocusing quantity induced complex variation of the ablation depth and the material removal rate. The maximum ablation depth and material removal rate were achieved at a defocusing position. The ablation depth and material removal rate oppositely varied about the scanning pitch. A high overlap ratio was meaningful for achieving a smooth micro-structure surface topography. Laser machining with a large defocusing quantity, high laser power and small scanning pitch was helpful for acquiring the desired micro-structure which had a large depth and smooth micro-structure surface topography.

Investigations of Effect of Rotary EDM Electrode on Machining Performance of Al6061 Alloy

Science.gov (United States)

Robinson Smart, D. S.; Jenish Smart, Joses; Periasamy, C.; Ratna Kumar, P. S. Samuel

2018-04-01

Electric Discharge Machining is an essential process which is being used for machining desired shape using electrical discharges which creates sparks. There will be electrodes subjected to electric voltage and which are separated by a dielectric liquid. Removing of material will be due to the continuous and rapid current discharges between two electrodes.. The spark is very carefully controlled and localized so that it only affects the surface of the material. Usually in order to prevent the defects which are arising due to the conventional machining, the Electric Discharge Machining (EDM) machining is preferred. Also intricate and complicated shapes can be machined effectively by use of Electric Discharge Machining (EDM). The EDM process usually does not affect the heat treat below the surface. This research work focus on the design and fabrication of rotary EDM tool for machining Al6061alloy and investigation of effect of rotary tool on surface finish, material removal rate and tool wear rate. Also the effect of machining parameters of EDM such as pulse on & off time, current on material Removal Rate (MRR), Surface Roughness (SR) and Electrode wear rate (EWR) have studied. Al6061 alloy can be used for marine and offshore applications by reinforcing some other elements. The investigations have revealed that MRR (material removal rate), surface roughness (Ra) have been improved with the reduction in the tool wear rate (TWR) when the tool is rotating instead of stationary. It was clear that as rotary speed of the tool is increasing the material removal rate is increasing with the reduction of surface finish and tool wear rate.

How Blue-Collar Workers on 4-Day Workweeks Use Their Time

Science.gov (United States)

Maklan, David Mark

1977-01-01

Describes a study of the behavior of male blue-collar workers on 4-day workweeks, revealing that they participate in the same activities as similar 5-day workers. Discussion focuses on the impact of the 4-day week on use of time and on the individual's satisfaction with leisure activities. (TA)

Biometric monitor with electronics disposed on or in a neck collar

NARCIS (Netherlands)

2012-01-01

A highly portable biometric monitor is disclosed. At least one remote sensor member (12, 12') includes one or more biometric sensors (20, 22, 24, 25) configured for operative coupling with a patient. A neck collar (14, 114, 214, 314, 414) includes electronics (36, 40, 42, 44, 46, 48) for operating

Psychosocial Risk Factors and Musculoskeletal Symptoms among White and Blue-collar Workers at Private and Public Sectors.

Science.gov (United States)

Januario, Leticia B; Batistao, Mariana V; Coury, Helenice Jcg; Oliveira, Ana Beatriz; Sato, Tatiana O

2014-01-01

The aim of this study was to evaluate musculoskeletal and psychosocial perception and compare these conditions regarding the type of job (white or blue-collar) and the type of management model (private or public). Forty-seven public white-collar (PuWC), 84 private white-collar (PrWC) and 83 blue-collar workers (PrBC) were evaluated. Job Content Questionnaire (JCQ) and Utrecht Work Engagement Scale (UWES) were applied to evaluate psychosocial factors. Nordic Musculoskeletal Questionnaire (NMQ) was used to assess musculoskeletal symptoms. Pressure Pain Threshold (PPT) was measured to evaluate sensory responses. According to JCQ, all groups were classified as active profile. There was a significant association between work engagement and workers' categories (p workers had the highest scores for all the UWES domains, while PrBC had the lowest ones. PPT showed that PrBC workers had an increased sensitivity for left deltoid (p workers had an increased sensitivity for both epicondyles than PuWC (right p  0.05). This study showed differences in psychosocial risk factors and musculoskeletal symptoms in workers engaged in different types of jobs and work organization. Personal and work-related characteristics, psychosocial factors and PPT responses were different across workers' group. Despite all, there was no significant difference in reported symptoms across the groups, possibly indicating that the physical load is similar among the sectors.

Original Paper Effects of oxen yoke and donkey collar on traction ...

African Journals Online (AJOL)

The realization of mechanized zaï with draft animal encounters the weakness of hitch traction capabilities. To overcome this issue, a study was conducted in three villages in the northern Burkina Faso with the aim at evaluating the effect of improved yoke and improved collar respectively with oxen and donkey harnessing on ...

Characterization of Newcastle disease virus isolates obtained from Eurasian collared doves (Streptopelia decaocto) in Italy.

Science.gov (United States)

Terregino, Calogero; Cattoli, Giovanni; Grossele, Barbara; Bertoli, Elena; Tisato, Ernesto; Capua, Ilaria

2003-02-01

Eurasian collared doves (Streptopelia decaocto) are thought to originate from India and they have colonized, throughout the centuries, the Middle East and, more recently, Mediterranean countries such as Italy and Spain. In the present paper we report of the isolation and characterization of Newcastle disease viruses (NDV) obtained from Eurasian collared doves during 2000-2001, and compare them to isolates obtained from feral pigeons (Columba livia) during the same period. All isolates could be classified as avian paramyxovirus type 1 (APMV1) and belonged to the pigeon variant group (PPMV1), as their haemagglutinating activity was inhibited by mAb 161/617 which is specific for PPMV1. The intracerebral pathogenicity indices ranged from 0.68 to 1.38 and all isolates contained multiple basic amino acids at the deduced cleavage site of the fusion protein, which is a typical feature of virulent viruses. Phylogenetic analysis of the isolates indicate that 18/20 of these form a separate cluster from the isolates obtained from pigeons in the same period. These findings suggest that different lineages are circulating in feral pigeon populations, and that a separate lineage affects Eurasian collared doves.

MtDNA genetic diversity and structure of Eurasian Collared Dove (Streptopelia decaocto).

Science.gov (United States)

Bagi, Zoltán; Dimopoulos, Evangelos Antonis; Loukovitis, Dimitrios; Eraud, Cyril; Kusza, Szilvia

2018-01-01

The Eurasian Collared Dove (Streptopelia decaocto) is one of the most successful biological invaders among terrestrial vertebrates. However, little information is available on the genetic diversity of the species. A total of 134 Eurasian Collared Doves from Europe, Asia and the Caribbean (n = 20) were studied by sequencing a 658-bp length of mitochondrial DNA (mtDNA) cytochrome oxidase I (COI). Fifty-two different haplotypes and relatively high haplotype and nucleotide diversities (Hd±SD = 0.843±0.037 and π±SD = 0.026±0.013) were detected. Haplotype Ht1 was particularly dominant: it included 44.03% of the studied individuals, and contained sequences from 75% of the studied countries. Various analyses (FST, AMOVA, STRUCTURE) distinguished 2 groups on the genetic level, designated 'A' and 'B'. Two groups were also separated in the median-joining network and the maximum likelihood tree. The results of the neutrality tests were negative (Fu FS = -25.914; Tajima D = -2.606) and significantly different from zero (P≤0.001) for group A, whereas both values for group B were positive (Fu FS = 1.811; Tajima D = 0.674) and not significant (P>0.05). Statistically significant positive autocorrelation was revealed among individuals located up to 2000 km apart (r = 0.124; P = 0.001). The present results provide the first information on the genetic diversity and structure of the Eurasian Collared Dove, and can thereby serve as a factual and comparative basis for similar studies in the future.

Removable top nozzle and tool for a nuclear reactor fuel assembly

International Nuclear Information System (INIS)

Wilson, J.F.; Cerni, S.; Gjertsen, R.K.

1987-01-01

A tool is described used in a nuclear reactor fuel assembly for connecting and disconnecting an internally threaded collar threadably engagable with an externally threaded upper end of a control rod guide thimble. The tool consists of: (a) rotation means engagable with the collar and operable to apply a torque in one direction to threadably connect the internally threaded collar on the thimble's externally threaded upper end and in an opposite direction to disconnect the collar from its threaded connection with the thimble; and (b) gripper means adapted to be inserted into the upper end of the guide thimble and operable to prevent the thimble from rotating about its longitudinal axis as the rotation means applies torque to the collar in connecting and disconnecting the collar on and off the guide thimble; (c) the gripper means being disposed within the rotation means and having a portion thereof projecting outwardly beyond the rotation means for insertion into the thimble when the rotation means is engaged with the collar

Understanding workplace boredom among white collar employees : temporary reactions and individual differences

NARCIS (Netherlands)

Heijden, van der G.A.H.; Schepers, J.J.L.; Nijssen, E.J.

2012-01-01

The purpose of this study is to investigate white collar employees' temporary relief strategies to workplace boredom. Building on self-regulation theory we define two responses: engaging in distraction and work indifference. We also investigate whether some individuals are more likely to engage in

Using computerised surface wound mapping to compare the potential medical effectiveness of Enhanced Protection Under Body Armour Combat Shirt collar designs.

Science.gov (United States)

Breeze, John; Allanson-Bailey, L C; Hunt, N C; Delaney, R; Hepper, A E; Lewis, E A

2015-03-01

Protecting the neck from explosively propelled fragments has traditionally been achieved through a collar attached to the ballistic vest. An Enhanced Protection Under Body Armour Combat Shirt (EP-UBACS) collar has been identified as an additional method of providing neck protection but limited evidence as to its potential medical effectiveness exists to justify its procurement. Entry wound locations and resultant medical outcomes were determined using Abbreviated Injury Scale (AIS) for all fragmentation neck wounds sustained by UK soldiers between 01 January 2010 and 31 December 2011. Data were prospectively entered into a novel computerised tool base and comparisons made between three EP-UBACS neck collar designs in terms of predicted reduction in AIS scores. All collars reduced AIS scores, with the greatest reduction provided by designs incorporating increased standoff from the neck and an additional semi-circle of ballistic material underneath the collar at the front and back. This technique confirms that reinforcing the neck collar of an EP-UBACS would be expected to reduce injury severity from neck wounds. However, without knowledge of entry wound locations for injuries to other body areas as well as the use of AIS scores without clinical or pathological verification its further use in the future may be limited. The ability to overlay any armour design onto a standardised human was potentially the most useful part of this tool and we would recommend developing this technique using underlying anatomical structures and not just the skin surface. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

Does Abutment Collar Length Affect Abutment Screw Loosening After Cyclic Loading?

Science.gov (United States)

Siadat, Hakimeh; Pirmoazen, Salma; Beyabanaki, Elaheh; Alikhasi, Marzieh

2015-07-01

A significant vertical space that is corrected with vertical ridge augmentation may necessitate selection of longer abutments, which would lead to an increased vertical cantilever. This study investigated the influence of different abutment collar heights on single-unit dental implant screw-loosening after cyclic loading. Fifteen implant-abutment assemblies each consisted of an internal hexagonal implant were randomly assigned to 3 groups: Group1, consisting of 5 abutments with 1.5 mm gingival height (GH); Group2, 5 abutments with 3.5 mm GH; and Group3, 5 abutments with 5.5 mm GH. Each specimen was mounted in transparent auto-polymerizing acrylic resin block, and the abutment screw was tightened to 35 Ncm with an electric torque wrench. After 5 minutes, initial torque loss (ITL) was recorded for all specimens. Metal crowns were fabricated with 45° occlusal surface and were placed on the abutments. A cyclic load of 75 N and frequency of 1 Hz were applied perpendicular to the long axis of each specimen. After 500 000 cycles, secondary torque loss (STL) was recorded. One-way ANOVA analysis was used to evaluate the effects of abutment collar height before and after cyclic loading. One-way ANOVA showed that ITL among the groups was not significantly different (P = .52), while STL was significantly different among the groups (P = .008). Post-hoc Tukey HSD tests showed that STL values were significantly different between the abutments with 1.5 mm GH (Group1) and with 5.5 mm GH (Group3) (P = .007). A paired comparison t-test showed that cyclic loading significantly influenced the STL in comparison with the ITL in each group. Within the limitations of this study, it can be concluded that increase in height of the abutment collar could adversely affect the torque loss of the abutment screw.

Slide system for machine tools

Science.gov (United States)

Douglass, Spivey S.; Green, Walter L.

1982-01-01

The present invention relates to a machine tool which permits the machining of nonaxisymmetric surfaces on a workpiece while rotating the workpiece about a central axis of rotation. The machine tool comprises a conventional two-slide system (X-Y) with one of these slides being provided with a relatively short travel high-speed auxiliary slide which carries the material-removing tool. The auxiliary slide is synchronized with the spindle speed and the position of the other two slides and provides a high-speed reciprocating motion required for the displacement of the cutting tool for generating a nonaxisymmetric surface at a selected location on the workpiece.

Fatigue as prognostic risk marker of mental sickness absence in white collar employees.

Science.gov (United States)

Roelen, C A M; Heymans, M W; van Rhenen, W; Groothoff, J W; Twisk, J W R; Bültmann, U

2014-06-01

To investigate fatigue as prognostic risk marker for identifying working employees at risk of long-term sickness absence (SA). At baseline, fatigue was measured in 633 white collar employees with the checklist individual strength (CIS) including scales for fatigue severity, reduced concentration, reduced motivation, and reduced physical activity. SA was medically certified by an occupational physician in the 3rd or 4th SA week with diagnostic codes according to the 10th version of the International Classification of Diseases. Medically certified SA was retrieved at the individual level from an occupational health register after 1-year follow-up. CIS scores were investigated as prognostic risk markers predicting medically certified SA and particularly SA certified as mental SA. 614 employees (N = 378 men and N = 236 women) had complete data and were eligible for analysis; 63 (10 %) had medically certified SA of whom 39 (6 %) had mental SA. Fatigue severity and total CIS scores were associated with medically certified SA in men, but poorly discriminated between men with and without medically certified SA. Fatigue severity, reduced concentration, reduced motivation, and total CIS scores were also associated with mental SA in men. CIS and its reduced concentration scale were valid prognostic risk markers of mental SA. CONCLUSION Fatigue was a prognostic risk marker of mental SA in white collar men. The CIS should be further validated as a screening tool for the risk of mental SA in white collar working populations.

Cleaning of aluminum after machining with coolants

International Nuclear Information System (INIS)

Roop, B.

1992-01-01

An x-ray photoemission spectroscopic study was undertaken to compare the cleaning of the Advanced Photon Source (APS) aluminum extrusion storage ring vacuum chambers after machining with and without water soluble coolants. While there was significant contamination left by the coolants, the cleaning process was capable of removing the residue. The variation of the surface and near surface composition of samples machined either dry or with coolants was negligible after cleaning. The use of such coolants in the machining process is therefore recommended

Charging machine

International Nuclear Information System (INIS)

Medlin, J.B.

1976-01-01

A charging machine for loading fuel slugs into the process tubes of a nuclear reactor includes a tubular housing connected to the process tube, a charging trough connected to the other end of the tubular housing, a device for loading the charging trough with a group of fuel slugs, means for equalizing the coolant pressure in the charging trough with the pressure in the process tubes, means for pushing the group of fuel slugs into the process tube and a latch and a seal engaging the last object in the group of fuel slugs to prevent the fuel slugs from being ejected from the process tube when the pusher is removed and to prevent pressure liquid from entering the charging machine. 3 claims, 11 drawing figures

Advanced SLARette delivery machine

International Nuclear Information System (INIS)

Bodner, R.R.

1995-01-01

SLARette 1 equipment, comprising of a SLARette Delivery Machine, SLAR Tools, SLAR power supplies and SLAR Inspection Systems was designed, developed and manufactured to service fuel channels of CANDU 6 stations during the regular yearly station outages. The Mark 2 SLARette Delivery Machine uses a Push Tube system to provide the axial and rotary movements of the SLAR Tool. The Push Tubes are operated remotely but must be attached and removed manually. Since this operation is performed at the Reactor face, there is radiation dose involved for the workers. An Advanced SLARette Delivery Machine which incorporates a computer controlled telescoping Ram in the place of the Push Tubes has been recently designed and manufactured. Utilization of the Advanced SLARette Delivery Machine significantly reduces the amount of radiation dose picked up by the workers because the need to have workers at the face of the Reactor during the SLARette operation is greatly reduced. This paper describes the design, development and manufacturing process utilized to produce the Advanced SLARette Delivery Machine and the experience gained during the Gentilly-2 NGS Spring outage. (author)

33 CFR 157.170 - COW equipment: Removal.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false COW equipment: Removal. 157.170... Crude Oil Washing (COW) System on Tank Vessels Cow Operations § 157.170 COW equipment: Removal. (a) Whenever a deck mounted COW machine is removed from the tank, the master shall ensure that: (1) The supply...

Biomechanical comparison of two different collar structured implants supporting 3-unit fixed partial denture: a 3-D FEM study.

Science.gov (United States)

Meriç, Gökçe; Erkmen, Erkan; Kurt, Ahmet; Eser, Atilim; Ozden, Ahmet Utku

2012-01-01

The purpose of the study was to compare the effects of two distinct collar geometries of implants on stress distribution in the bone as well as in the fixture-abutment complex, in the framework and in the veneering material of 3-unit fixed partial denture (FPD). The 3-dimensional finite element analysis method was selected to evaluate the stress distribution in the system composed of 3-unit FPD supported by two different dental implant systems with two distinct collar geometries; microthread collar structure (MCS) and non-microthread collar structure (NMCS). In separate load cases, 300 N vertical, 150 N oblique and 60 N horizontal, forces were utilized to simulate the multidirectional chewing forces. Tensile and compressive stress values in the cortical and cancellous bone and von Mises stresses in the fixture-abutment complex, in the framework and veneering material, were simulated as a body and investigated separately. In the cortical bone lower stress values were found in the MCS model, when compared with NMCS. In the cancellous bone, lower stress values were observed in the NMCS model when compared with MCS. In the implant-abutment complex, highest von Mises stress values were noted in the NMCS model; however, in the framework and veneering material, highest stress values were calculated in MCS model. MCS implants when compared with NMCS implants supporting 3-unit FPDs decrease the stress values in the cortical bone and implant-abutment complex. The results of the present study will be evaluated as a base for our ongoing FEA studies focused on stress distribution around the microthread and non-microthread collar geometries with various prosthesis design.

Effectiveness of dog collars impregnated with 4% deltamethrin in controlling visceral leishmaniasis in Lutzomyia longipalpis (Diptera: Psychodidade: Phlebotominae) populations.

Science.gov (United States)

Silva, Rafaella Albuquerque E; Andrade, Andrey José de; Quint, Bruno Beust; Raffoul, Gabriel Elias Salmen; Werneck, Guilherme Loureiro; Rangel, Elizabeth Ferreira; Romero, Gustavo Adolfo Sierra

2018-03-26

There is little information on the effect of using deltamethrin-impregnated dog collars for the control of canine visceral leishmaniasis. The objective of this study was to evaluate the effectiveness of the use of 4% deltamethrin-impregnated collars (Scalibor®) in controlling visceral leishmaniasis in Lutzomyia longipalpis by comparing populations in intervention and non-intervention areas. Phlebotomine flies were captured over 30 months in four neighbourhoods with intense visceral leishmaniasis transmission in Fortaleza and Montes Claros. We calculated the rates of domicile infestation, relative abundance of Lu. longipalpis, and Lu. longipalpis distribution in each site, capture location (intra- and peridomestic locations) and area (intervention and non-intervention areas). In the control area in Fortaleza, the relative abundance of Lu. longipalpis was 415 specimens at each capture site, whereas in the intervention area it was 159.25; in Montes Claros, the relative abundance was 5,660 specimens per capture site in the control area, whereas in the intervention area it was 2,499.4. The use of dog collars was associated with a reduction in captured insects of 15% (p = 0.004) and 60% (p < 0.001) in Montes Claros and Fortaleza, respectively. We observed a lower vector abundance in the intervention areas, suggesting an effect of the insecticide-impregnated collars.

Serologic Survey for Selected Viral and Bacterial Swine Pathogens in Colombian Collared Peccaries ( Pecari tajacu) and Feral Pigs ( Sus scrofa).

Science.gov (United States)

Montenegro, Olga L; Roncancio, Nestor; Soler-Tovar, Diego; Cortés-Duque, Jimena; Contreras-Herrera, Jorge; Sabogal, Sandra; Acevedo, Luz Dary; Navas-Suárez, Pedro Enrique

2018-06-14

In South America, wild populations of peccaries coexist with domestic and feral pigs, with poorly understood consequences. We captured 58 collared peccaries ( Pecari tajacu) and 15 feral pigs ( Sus scrofa) in locations of Colombia where coexistence of these species is known. Blood samples were tested for antibodies against four viral agents, classical swine fever virus (CSFV), Aujeszky's disease virus (ADV), porcine circovirus (PCV-2), and vesicular stomatitis virus (New Jersey and Indiana subtypes) and two bacterial agents, Brucella spp. and six serovars of Leptospira interrogans. The prevalence of CSFV was 5% (3/58) in collared peccaries and 7% (1/15) in feral pigs. The prevalence of PCV-2 was 7% (1/15) in collared peccaries and 67% (2/3) in feral pigs. Vesicular stomatitis prevalence was 33% (8/24) in collared peccaries and 67% (4/6) in feral pigs. Leptospira prevalence was 78% (39/50) in collared peccary and 100% (8/8) in feral pigs; bratislava, grippotyphosa, icterohaemorrhagiae, and pomona were the most frequent serovars. Also, the only white-lipped peccary ( Tayassu pecari) sampled was positive for L. interrogans serovar bratislava and for vesicular stomatitis virus, New Jersey strain. No samples were positive for ADV or Brucella. The seroprevalence of antibodies against L. interrogans was similar to that observed in other studies. Icterohaemorrhagiae appears to be a common serovar among in situ and ex situ peccary populations. Positive antibodies against PVC-2 represent a novel report of exposure to this pathogen in Colombian peccaries. Our results indicate the possible transmission of various pathogens, important for pig farms, in the studied pig and peccaries.

[Limits of self regulation of the private food sector: the case of removing of vending machines from schools].

Science.gov (United States)

Michaud, Claude; Baudier, François

2007-01-01

Conflicts of interest between the food industry and public decision makers have increasingly multiplied over the last few years, especially within the context of implementing the French National Nutrition Programme. This paper describes the rhetoric and the strategies developed by the private sector in order to counter the law's implementation and enforcement based on a concrete example, namely, the removal of vending machines from schools. After having evoked possibilities of developing new partnerships as suggested by national and international health authorities, it reaffirms the right and the duty of the State to regulate within the framework of a health promotion policy, an approach which integrates the necessary open democratic public debate between the different sectors.

Characteristics of combustion flame sprayed nickel aluminum using a Coanda Assisted Spray Manipulation collar for off-normal deposits

Science.gov (United States)

Archibald, Reid S.

A novel flame spray collar called the Coanda Assisted Spray Manipulation collar (CSM) has been tested for use on the Sulzer Metco 5P II combustion flame spray gun. A comparison study of the stock nozzle and the CSM has been performed by evaluating the porosity, surface roughness, microhardness, tensile strength and microscopy of normal and off-normal sprayed NiAl deposits. The use of the CSM collar resulted in the need to position the sprayed coupons closer to the gun, which in turn affected the particle impact energy and particle temperatures of the NiAl powder. For the CSM, porosities had a larger scatterband, surface roughness was comparably the same, microhardness was lower, and tensile strength was higher. The microscopy analysis revealed a greater presence of unmelted particles and steeper intersplat boundaries for the CSM. For both processes, the porosity and surface roughness increased and the microhardness decreased as the spray angle decreased.

The Association between Training and Organizational Commitment among White-Collar Workers in Malaysia.

Science.gov (United States)

Ahmad, Kamarul Zaman; Bakar, Raida Abu

2003-01-01

Responses from 204 of 300 Malaysian white-collar workers were analyzed for the association between training variables (availability of support, benefits, motivation, environment) and four types of organizational commitment. All training variables were significantly correlated with affective, normative, and overall commitment. Availability of…

Supporting and guiding device that is leak-tight and can be dismantled for the shaft of a rotating machine

International Nuclear Information System (INIS)

Tigoulet, Bernard; Fanchtein, J.P.; Dubost, Rene.

1982-01-01

This device includes a removable bearing casing crossed by at least one shaft of the machine, facilities for guiding this casing in parallel with the axis of the shaft so as to facilitate its removal and refitting, a system for supporting the shaft when the removable casing is not fitted in the machine frame. Application to machines for the extrusion of coating bitumen for radioactive waste [fr

"Blue-Collar Blues" uurib töösuhteid uutes oludes / Janar Ala

Index Scriptorium Estoniae

Ala, Janar, 1979-

2009-01-01

Tööproblemaatikat käsitlev näitus "Blue-Collar Blues" Tallinna Kunstihoones ja Tallinna Kunstihoone galeriis 31. jaanuarini 2010, kuraator Anders Härm. Lähemalt belgia-mehhiko kunstniku Francis Alys'e videost, austria kunstniku Oliver Ressleri ning venetsueela-saksa politoloogi Dario Azzelini videost "Viis tehast. Tööliste kontroll Venezuelas"

Influence of electrical resistivity and machining parameters on electrical discharge machining performance of engineering ceramics.

Science.gov (United States)

Ji, Renjie; Liu, Yonghong; Diao, Ruiqiang; Xu, Chenchen; Li, Xiaopeng; Cai, Baoping; Zhang, Yanzhen

2014-01-01

Engineering ceramics have been widely used in modern industry for their excellent physical and mechanical properties, and they are difficult to machine owing to their high hardness and brittleness. Electrical discharge machining (EDM) is the appropriate process for machining engineering ceramics provided they are electrically conducting. However, the electrical resistivity of the popular engineering ceramics is higher, and there has been no research on the relationship between the EDM parameters and the electrical resistivity of the engineering ceramics. This paper investigates the effects of the electrical resistivity and EDM parameters such as tool polarity, pulse interval, and electrode material, on the ZnO/Al2O3 ceramic's EDM performance, in terms of the material removal rate (MRR), electrode wear ratio (EWR), and surface roughness (SR). The results show that the electrical resistivity and the EDM parameters have the great influence on the EDM performance. The ZnO/Al2O3 ceramic with the electrical resistivity up to 3410 Ω·cm can be effectively machined by EDM with the copper electrode, the negative tool polarity, and the shorter pulse interval. Under most machining conditions, the MRR increases, and the SR decreases with the decrease of electrical resistivity. Moreover, the tool polarity, and pulse interval affect the EWR, respectively, and the electrical resistivity and electrode material have a combined effect on the EWR. Furthermore, the EDM performance of ZnO/Al2O3 ceramic with the electrical resistivity higher than 687 Ω·cm is obviously different from that with the electrical resistivity lower than 687 Ω·cm, when the electrode material changes. The microstructure character analysis of the machined ZnO/Al2O3 ceramic surface shows that the ZnO/Al2O3 ceramic is removed by melting, evaporation and thermal spalling, and the material from the working fluid and the graphite electrode can transfer to the workpiece surface during electrical discharge

Machine Learning Techniques in Clinical Vision Sciences.

Science.gov (United States)

Caixinha, Miguel; Nunes, Sandrina

2017-01-01

This review presents and discusses the contribution of machine learning techniques for diagnosis and disease monitoring in the context of clinical vision science. Many ocular diseases leading to blindness can be halted or delayed when detected and treated at its earliest stages. With the recent developments in diagnostic devices, imaging and genomics, new sources of data for early disease detection and patients' management are now available. Machine learning techniques emerged in the biomedical sciences as clinical decision-support techniques to improve sensitivity and specificity of disease detection and monitoring, increasing objectively the clinical decision-making process. This manuscript presents a review in multimodal ocular disease diagnosis and monitoring based on machine learning approaches. In the first section, the technical issues related to the different machine learning approaches will be present. Machine learning techniques are used to automatically recognize complex patterns in a given dataset. These techniques allows creating homogeneous groups (unsupervised learning), or creating a classifier predicting group membership of new cases (supervised learning), when a group label is available for each case. To ensure a good performance of the machine learning techniques in a given dataset, all possible sources of bias should be removed or minimized. For that, the representativeness of the input dataset for the true population should be confirmed, the noise should be removed, the missing data should be treated and the data dimensionally (i.e., the number of parameters/features and the number of cases in the dataset) should be adjusted. The application of machine learning techniques in ocular disease diagnosis and monitoring will be presented and discussed in the second section of this manuscript. To show the clinical benefits of machine learning in clinical vision sciences, several examples will be presented in glaucoma, age-related macular degeneration

Estrus cycle monitoring of captive collared peccaries (Pecari tajacu in semiarid conditions

Directory of Open Access Journals (Sweden)

Keilla M. Maia

2014-11-01

Full Text Available Collared peccaries (Peccary tajacu are among the most hunted species in Latin America due the appreciation of their pelt and meat. In order to optimize breeding management of captive born collared peccaries in semiarid conditions, the objective was to describe and correlate the changes in the ovarian ultrasonographic pattern, hormonal profile, vulvar appearance, and vaginal cytology during the estrus cycle in this species. During 45 days, females (n=4 were subjected each three days to blood collection destined to hormonal dosage by enzyme immunoassay (EIA. In the same occasions, evaluation of external genitalia, ovarian ultrasonography and vaginal cytology were conducted. Results are presented as means and standard deviations. According to hormonal dosage, six estrous cycles were identified as lasting 21.0 ± 5.7 days, being on average 6 days for the estrogenic phase and 15 days for the progesterone phase. Estrogen presented mean peak values of 55.6 ± 20.5 pg/mL. During the luteal phase, the high values for progesterone were 35.3 ± 4.4 ng/mL. The presence of vaginal mucus, a reddish vaginal mucosa and the separation of the vulvar lips were verified in all animals during the estrogenic peak. Through ultrasonography, ovarian follicles measuring 0.2±0.1 cm were visualized during the estrogen peak. Corpora lutea presented hyperechoic regions measuring 0.4±0.2 cm identified during luteal phase. No significant differences (P>0.05 between proportions of vaginal epithelial cells were identified when comparing estrogenic and progesterone phases. In conclusion, female collared peccaries, captive born in semiarid conditions, have an estral cycle that lasts 21.0±5.7 days, with estrous signs characterized by vulvar lips edema and hyperemic vaginal mucosa, coinciding with developed follicles and high estrogen levels.

Reliability of electrode wear compensation based on material removal per discharge in micro EDM milling

DEFF Research Database (Denmark)

Bissacco, Giuliano; Tristo, G.; Hansen, Hans Nørgaard

2013-01-01

This paper investigates the reliability of workpiece material removal per discharge (MRD) estimation for application in electrode wear compensation based on workpiece material removal. An experimental investigation involving discharge counting and automatic on the machine measurement of removed...... material volume was carried out in a range of process parameters settings from fine finishing to roughing. MRD showed a decreasing trend with the progress of the machining operation, reaching stabilization after a number of machined layers. Using the information on MRD and discharge counting, a material...

Neck Collar with Mild Jugular Vein Compression Ameliorates Brain Activation Changes during a Working Memory Task after a Season of High School Football.

Science.gov (United States)

Yuan, Weihong; Leach, James; Maloney, Thomas; Altaye, Mekibib; Smith, David; Gubanich, Paul J; Barber Foss, Kim D; Thomas, Staci; DiCesare, Christopher A; Kiefer, Adam W; Myer, Gregory D

2017-08-15

Emerging evidence indicates that repetitive head impacts, even at a sub-concussive level, may result in exacerbated or prolonged neurological deficits in athletes. This study aimed to: 1) quantify the effect of repetitive head impacts on the alteration of neuronal activity based on functional magnetic resonance imaging (fMRI) of working memory after a high school football season; and 2) determine whether a neck collar that applies mild jugular vein compression designed to reduce brain energy absorption in head impact through "slosh" mitigation can ameliorate the altered fMRI activation during a working memory task. Participants were recruited from local high school football teams with 27 and 25 athletes assigned to the non-collar and collar group, respectively. A standard N-Back task was used to engage working memory in the fMRI at both pre- and post-season. The two study groups experienced similar head impact frequency and magnitude during the season (all p > 0.05). fMRI blood oxygen level dependent (BOLD) signal response (a reflection of the neuronal activity level) during the working memory task increased significantly from pre- to post-season in the non-collar group (corrected p working memory related brain activity, as well as a potential protective effect that resulted from the use of the purported brain slosh reducing neck collar in contact sports.

Socializing Messages in Blue-Collar Families: Communicative Pathways to Social Mobility and Reproduction

Science.gov (United States)

Lucas, Kristen

2011-01-01

This study explicitly links processes of anticipatory socialization to social mobility and reproduction. An examination of the socializing messages exchanged between blue-collar parents (n = 41) and their children (n = 25) demonstrate that family-based messages about work and career seldom occur in straightforward, unambiguous ways. Instead,…

An experimental investigation of pulsed laser-assisted machining of AISI 52100 steel

Science.gov (United States)

Panjehpour, Afshin; Soleymani Yazdi, Mohammad R.; Shoja-Razavi, Reza

2014-11-01

Grinding and hard turning are widely used for machining of hardened bearing steel parts. Laser-assisted machining (LAM) has emerged as an efficient alternative to grinding and hard turning for hardened steel parts. In most cases, continuous-wave lasers were used as a heat source to cause localized heating prior to material removal by a cutting tool. In this study, an experimental investigation of pulsed laser-assisted machining of AISI 52100 bearing steel was conducted. The effects of process parameters (i.e., laser mean power, pulse frequency, pulse energy, cutting speed and feed rate) on state variables (i.e., material removal temperature, specific cutting energy, surface roughness, microstructure, tool wear and chip formation) were investigated. At laser mean power of 425 W with frequency of 120 Hz and cutting speed of 70 m/min, the benefit of LAM was shown by 25% decrease in specific cutting energy and 18% improvement in surface roughness, as compared to those of the conventional machining. It was shown that at constant laser power, the increase of laser pulse energy causes the rapid increase in tool wear rate. Pulsed laser allowed efficient control of surface temperature and heat penetration in material removal region. Examination of the machined subsurface microstructure and microhardness profiles showed no change under LAM and conventional machining. Continuous chips with more uniform plastic deformation were produced in LAM.

"Blue-Collar Blues" : kõigi maade töötud, ühinege! / Ants Juske

Index Scriptorium Estoniae

Juske, Ants, 1956-2016

2009-01-01

Rahvusvaheline näitus "Blue-Collar Blues" Tallinna Kunstihoones ja Kunstihoone galeriis 31. jaanuarini 2010. Kuraator Anders Härm. Näituse ajendiks on 1. juulist 2009 Eestis kehtima hakanud töölepinguseadus, näituse fookus on töösuhetel

40 CFR 63.463 - Batch vapor and in-line cleaning machine standards.

Science.gov (United States)

2010-07-01

.... (3) Each cleaning machine shall have an automated parts handling system capable of moving parts or... of parts through removal of cleaned parts. (4) Each vapor cleaning machine shall be equipped with a...) and appendix A to this part. (2) Each owner or operator of a batch vapor cleaning machine with a...

An Examination of Blue- versus White-Collar Workers' Conceptualizations of Job Satisfaction Facets

Science.gov (United States)

Hu, Xiaoxiao; Kaplan, Seth; Dalal, Reeshad S.

2010-01-01

This study examined the degree to which blue- versus white-collar workers differentially conceptualize various job facets, namely the work itself, co-workers, supervisors, and pay. To examine these potential differences, we conducted a series of analyses on job satisfaction ratings from two samples of university workers. Consistent with the study…

Analysis of the collar-whisker structure of temperate lactococcal bacteriophage TP901-1

DEFF Research Database (Denmark)

Vegge, Christina Skovgaard; Neve, Horst; Brøndsted, Lone

2006-01-01

Proteins homologous to the protein NPS (neck passage structure) are widespread among lactococcal phages. We investigated the hypothesis that NPS is involved in the infection of phage TP901-1 by analysis of an NPS mutant. NPS was determined to form a collar-whisker complex but was shown to be none...

Increased effects of machining damage in beryllium observed at high strain rates

International Nuclear Information System (INIS)

Beitscher, S.; Brewer, A.W.; Corle, R.R.

1980-01-01

Tensile tests at both low and high strain rates, and also impact shear tests, were performed on a weldable grade powder-source beryllium. Impact energies increased by a factor of 2 to 3 from the as-machined level after etching or annealing. Similar increases in the ductility from machining damage removal were observed from the tensile data at the higher strain rate (10 s -1 ) while an insignificant increase in elongation was measured at the lower strain rate (10 -4 s -1 ). High strain-rate tests appear to be more sensitive and reliable for evaluating machining practice and damage removal methods for beryllium components subjected to sudden loads. 2 tables

High speed laser cutting machine. Kosoku reza kakoki

Energy Technology Data Exchange (ETDEWEB)

Shinno, N. (Matsushita Electric Industrial Co. Ltd., Kadoma, Osaka (Japan))

1993-11-01

The carbon dioxide gas laser cutting machine is being used widely for from cutting soft steel and stainless steel, etc. to intermetallic welding and in the field of cutting in particular, concerning sheet cutting, it has been changing the existing monopoly of the turret punch press, and as for medium and thick plate cutting, that of the gas plasma fusing device. This article is the general description of high speed laser cutting machine. Concerning the laser cutting (sheet cutting in particular), as the essential items for securing severe cutting accuracy and, at the same time, improving the cutting speed, the following matters are picked up for respective explanation; improvement of stationary machine accuracy, improvement of dynamic machine accuracy, improvement of quality of laser beam as well as optimization of cutting conditions, and shortening of piercing time. Also explanation is given to the respective items, namely speeding-up of medium and thick plate cutting, and reduction of load onto the operator by improved operation. Finally, feeding and removing of a sheet only, and feeding and removing with a pallet are mentioned as the efforts for automation and energy saving. 3 figs., 1 tab.

Tracking maize pollen development by the Leaf Collar Method.

Science.gov (United States)

Begcy, Kevin; Dresselhaus, Thomas

2017-12-01

An easy and highly reproducible nondestructive method named the Leaf Collar Method is described to identify and characterize the different stages of pollen development in maize. In plants, many cellular events such as meiosis, asymmetric cell division, cell cycle regulation, cell fate determination, nucleus movement, vacuole formation, chromatin condensation and epigenetic modifications take place during pollen development. In maize, pollen development occurs in tassels that are confined within the internal stalk of the plant. Hence, identification of the different pollen developmental stages as a tool to investigate above biological processes is impossible without dissecting the entire plant. Therefore, an efficient and reproducible method is necessary to isolate homogeneous cell populations at individual stages throughout pollen development without destroying the plant. Here, we describe a method to identify the various stages of pollen development in maize. Using the Leaf Collar Method in the maize inbreed line B73, we have determined the duration of each stage from pollen mother cells before meiosis to mature tricellular pollen. Anther and tassel size as well as percentage of pollen stages were correlated with vegetative stages, which are easily recognized. The identification of stage-specific genes indicates the reproducibility of the method. In summary, we present an easy and highly reproducible nondestructive method to identify and characterize the different stages of pollen development in maize. This method now opens the way for many subsequent physiological, morphological and molecular analyses to study, for instance, transcriptomics, metabolomics, DNA methylation and chromatin patterns during normal and stressful conditions throughout pollen development in one of the economically most important grass species.

Monitoring distances travelled by horses using GPS tracking collars.

Science.gov (United States)

Hampson, B A; Morton, J M; Mills, P C; Trotter, M G; Lamb, D W; Pollitt, C C

2010-05-01

The aims of this work were to (1) develop a low-cost equine movement tracking collar based on readily available components, (2) conduct preliminary studies assessing the effects of both paddock size and internal fence design on the movements of domestic horses, with and without foals at foot, and (3) describe distances moved by mares and their foals. Additional monitoring of free-ranging feral horses was conducted to allow preliminary comparisons with the movement of confined domestic horses. A lightweight global positioning system (GPS) data logger modified from a personal/vehicle tracker and mounted on a collar was used to monitor the movement of domestic horses in a range of paddock sizes and internal fence designs for 6.5-day periods. In the paddocks used (0.8-16 ha), groups of domestic horses exhibited a logarithmic response in mean daily distance travelled as a function of increasing paddock size, tending asymptotically towards approximately 7.5 km/day. The distance moved by newborn foals was similar to their dams, with total distance travelled also dependent on paddock size. Without altering available paddock area, paddock design, with the exception of a spiral design, did not significantly affect mean daily distance travelled. Feral horses (17.9 km/day) travelled substantially greater mean daily distances than domestic horses (7.2 km/day in 16-ha paddock), even when allowing for larger paddock size. Horses kept in stables or small yards and paddocks are quite sedentary in comparison with their feral relatives. For a given paddock area, most designs did not significantly affect mean daily distance travelled.

Sperm morphological and morphometric evaluation in captive collared peccaries (Pecari tajacu

Directory of Open Access Journals (Sweden)

Patrícia C. Sousa

2013-07-01

Full Text Available The aim of this study was to compare different staining methods for the evaluation of sperm morphology by light microscopy and also to describe the morphometry of the entire sperm in collared peccaries (Pecari tajacu. Semen from 10 males was obtained by electroejaculation and evaluated for sperm motility, vigor, and concentration. Semen smears were prepared through three different staining methods: Bengal rose, brome-phenol blue, and eosin-nigrosin. Smears were evaluated under light microscopy and sperm morphologic alterations were determined in percentage. In addition, sperm morphometric analysis was conducted by light microscopy coupled to image analyzer software. The smears stained with Bengal Rose provide the best results for the visualization of the sperm tail, midpiece, and head. The use of eosin-nigrosin stain did not allow an adequate impregnation, and some sperm presented a few contrasts with the background. A higher incidence of bent coiled tails was verified in the use of brome-phenol blue staining (P<0.05. Through morphometric evaluation, it was observed that the tail occupies the greatest proportion (89% of the sperm which presents a discretely elongated head. According to the results, the use of the Bengal Rose stain is recommended for the morphologic evaluation of the collared peccary sperm.

The machinability of cast titanium and Ti-6Al-4V.

Science.gov (United States)

Ohkubo, C; Watanabe, I; Ford, J P; Nakajima, H; Hosoi, T; Okabe, T

2000-02-01

This study investigated the machinability (ease of metal removal) of commercially pure (CP) titanium and Ti-6Al-4V alloy. Both CP Ti and Ti-6Al-4V were cast into magnesia molds. Two types of specimens (with alpha-case and without alpha-case) were made for CP Ti and Ti-6Al-4V. Machinability (n = 5) was evaluated as volume loss (mm3) by cutting/grinding the 3.0 mm surface using fissure burs and silicon carbide (SiC) under two machining conditions: (1) two machining forces (100 or 300 gf) at two rotational speeds (15000 or 30000 rpm) for 1 min, and (2) constant machining force of 100 gf and rotational speed of 15000 rpm for 1, 2, 5, 10, and 30 min. As controls, conventionally cast Co-Cr and Type IV gold alloys were evaluated in the same manner as the titanium. When fissure burs were used, there was a significant difference in the machinability between CP titanium with alpha-case and without alpha-case. On the other hand, there was no appreciable difference in the amount of metal removed for each tested metal when using the SiC points.

Nano Mechanical Machining Using AFM Probe

Science.gov (United States)

Mostofa, Md. Golam

Complex miniaturized components with high form accuracy will play key roles in the future development of many products, as they provide portability, disposability, lower material consumption in production, low power consumption during operation, lower sample requirements for testing, and higher heat transfer due to their very high surface-to-volume ratio. Given the high market demand for such micro and nano featured components, different manufacturing methods have been developed for their fabrication. Some of the common technologies in micro/nano fabrication are photolithography, electron beam lithography, X-ray lithography and other semiconductor processing techniques. Although these methods are capable of fabricating micro/nano structures with a resolution of less than a few nanometers, some of the shortcomings associated with these methods, such as high production costs for customized products, limited material choices, necessitate the development of other fabricating techniques. Micro/nano mechanical machining, such an atomic force microscope (AFM) probe based nano fabrication, has, therefore, been used to overcome some the major restrictions of the traditional processes. This technique removes material from the workpiece by engaging micro/nano size cutting tool (i.e. AFM probe) and is applicable on a wider range of materials compared to the photolithographic process. In spite of the unique benefits of nano mechanical machining, there are also some challenges with this technique, since the scale is reduced, such as size effects, burr formations, chip adhesions, fragility of tools and tool wear. Moreover, AFM based machining does not have any rotational movement, which makes fabrication of 3D features more difficult. Thus, vibration-assisted machining is introduced into AFM probe based nano mechanical machining to overcome the limitations associated with the conventional AFM probe based scratching method. Vibration-assisted machining reduced the cutting forces

Electrochemical Machining – Special Equipment and Applications in Aircraft Industry

Directory of Open Access Journals (Sweden)

Ruszaj Adam

2016-06-01

Full Text Available Electrochemical machining is an unique method of shaping in which, for optimal parameters tool has no wear, surface layer properties after machining are similar to the core material and surface quality and accuracy increase together with material removal rate increase. Such advantages of electrochemical machining, besides of some ecological problems, create industry interest in the range of manufacturing elements made of materials with special properties (i.e. turbine blades of flow aircrafts engines. In the paper the nowadays possibilities and recent practical application of electrochemical machining in aircraft have been presented.

Plectosphaerella species associated with root and collar rots of horticultural crops in southern Italy

NARCIS (Netherlands)

Carlucci, A.; Raimondo, M.L.; Santos, J.; Phillips, A.J.L.

2012-01-01

Plectosphaerella cucumerina, most frequently encountered in its Plectosporium state, is well known as a pathogen of several plant species causing fruit, root and collar rot, and collapse. It is considered to pose a serious threat to melon (Cucumis melo) production in Italy. In the present study, an

Job Attitudes of Black and White Workers: Male Blue-Collar Workers in Six Companies

Science.gov (United States)

Katzell, Raymond A.; And Others

1974-01-01

A 74-item attitude questionnaire was administered in six companies to 101 black and 87 white male blue-collar employees holding similar jobs in the same company. Differences between the two ethnic groups were not marked, both in terms of job satisfaction and in other respects. (Author)

Machining of Fibre Reinforced Plastic Composite Materials

Science.gov (United States)

2018-01-01

Fibre reinforced plastic composite materials are difficult to machine because of the anisotropy and inhomogeneity characterizing their microstructure and the abrasiveness of their reinforcement components. During machining, very rapid cutting tool wear development is experienced, and surface integrity damage is often produced in the machined parts. An accurate selection of the proper tool and machining conditions is therefore required, taking into account that the phenomena responsible for material removal in cutting of fibre reinforced plastic composite materials are fundamentally different from those of conventional metals and their alloys. To date, composite materials are increasingly used in several manufacturing sectors, such as the aerospace and automotive industry, and several research efforts have been spent to improve their machining processes. In the present review, the key issues that are concerning the machining of fibre reinforced plastic composite materials are discussed with reference to the main recent research works in the field, while considering both conventional and unconventional machining processes and reporting the more recent research achievements. For the different machining processes, the main results characterizing the recent research works and the trends for process developments are presented. PMID:29562635

Machining of Fibre Reinforced Plastic Composite Materials

Directory of Open Access Journals (Sweden)

Alessandra Caggiano

2018-03-01

Full Text Available Fibre reinforced plastic composite materials are difficult to machine because of the anisotropy and inhomogeneity characterizing their microstructure and the abrasiveness of their reinforcement components. During machining, very rapid cutting tool wear development is experienced, and surface integrity damage is often produced in the machined parts. An accurate selection of the proper tool and machining conditions is therefore required, taking into account that the phenomena responsible for material removal in cutting of fibre reinforced plastic composite materials are fundamentally different from those of conventional metals and their alloys. To date, composite materials are increasingly used in several manufacturing sectors, such as the aerospace and automotive industry, and several research efforts have been spent to improve their machining processes. In the present review, the key issues that are concerning the machining of fibre reinforced plastic composite materials are discussed with reference to the main recent research works in the field, while considering both conventional and unconventional machining processes and reporting the more recent research achievements. For the different machining processes, the main results characterizing the recent research works and the trends for process developments are presented.

The relationship between meeting of recommendations on physical activity for health and perceived work ability among white-collar workers.

Science.gov (United States)

Nawrocka, Agnieszka; Garbaciak, Wiesław; Cholewa, Jarosław; Mynarski, Władysław

2018-04-01

The aim of this study was to evaluate the association between meeting recommendations on physical activity for health in leisure-time and the ability to work among Polish white-collar workers. The study used a cross-sectional design with a convenience sample of 360 white-collar workers. Participants recorded 7-day physical activity logs, including form, duration and intensity of leisure-time physical activities. The results were compared to health recommendations. A standardized Work Ability Index (WAI) questionnaire was used in assessing the ability to work. Participants who met health recommendations achieved higher scores of the WAI (mean score = 41.93) in comparison to those who were not sufficiently physically active (mean score = 39.35) (p health-related physical activity recommendations almost double the odds of reaching at least good work ability (OR = 1.94, 95% CI = 1.12-3.36). Meeting leisure-time physical activity recommendations (especially the criterion of vigorous physical activity) is significantly related to higher self-assessed ability to work among white-collar workers.

Resolution of a periodontoid rheumatoid pannus mass in an elderly patient treated with a rigid cervical collar: A case report and literature review.

Science.gov (United States)

Oseni, Abidemi; Kakavas, Georg; Scholz, Martin; Petridis, Athanasios

2016-06-17

In patients with C2 rheumatoid pannus with spinal cord compression the treatment of choice is extensive surgery either through a transoral resection of the dens axis or a dorsal stabilisation, or both. We present a case of an 11-mm rheumatoid pannus with significant compression of the spinal cord, which failed surgical treatment with respect to dorsal stabilisation. Therefore, rigid cervical collar for 8 weeks followed by soft collar for another 4 weeks was chosen as a treatment option. During the follow-up period of 1 year, the pannus reduced significantly and the spinal cord decompressed. In cases where surgery is not an option or is technically very demanding, the alternative of cervical collar immobilisation is a satisfying option.

A study of the health-related quality of life and work-related stress of white-collar migrant workers.

Science.gov (United States)

Tsai, Su-Ying

2012-10-19

Little is known about the health-related quality of life (HRQoL) and work-related stress and its risk factors among white-collar businessmen and management workers that migrate to high-income developing countries. A structural questionnaire survey was administered to 156 white-collar Taiwanese management personnel of representative companies of their industries in Taiwan, who were assigned long-term job positions in China. Questionnaire content included demographics and medical history, self-reported physical and mental conditions, personal lifestyle and behavior, Beck Depression Inventory, and information on HRQoL. White-collar migrant workers reported a high prevalence of alcohol consumption (72.4%) and perceived work-related stress (62.2%), and a lower prevalence of regular exercise (12.2%). Workers with higher levels of perceived work-related stress reported more alcohol consumption, a history of hyperlipidemia, and a higher prevalence of self-reported neck pain, poor sleep, and mild/moderate/severe depression. In our primary multivariate risk model to determine lifestyle and work-related stress variables and HRQoL, perceived work-related stress and a feeling of depression negatively impacted both the Physical Component Summary (PCS) and Mental Component Summary (MCS) scores of the SF-36 health survey. Hyperlipidemia and self-reported neck pain were associated with significantly lower PCS scores, whereas cardiovascular disease, gastric ulcer, and poor sleep were associated with statistically lower MCS scores. White-collar migrant workers are generally younger with high socioeconomic status. Perceived work-related stress and a feeling of depression indirectly affect HRQoL. Hyperlipidemia, self-reported neck pain, cardiovascular disease, gastric ulcer, and poor sleep also had a significant negative impact on HRQoL.

A Study of the Health-Related Quality of Life and Work-Related Stress of White-Collar Migrant Workers

Directory of Open Access Journals (Sweden)

Su-Ying Tsai

2012-10-01

Full Text Available Little is known about the health-related quality of life (HRQoL and work-related stress and its risk factors among white-collar businessmen and management workers that migrate to high-income developing countries. A structural questionnaire survey was administered to 156 white-collar Taiwanese management personnel of representative companies of their industries in Taiwan, who were assigned long-term job positions in China. Questionnaire content included demographics and medical history, self-reported physical and mental conditions, personal lifestyle and behavior, Beck Depression Inventory, and information on HRQoL. White-collar migrant workers reported a high prevalence of alcohol consumption (72.4% and perceived work-related stress (62.2%, and a lower prevalence of regular exercise (12.2%. Workers with higher levels of perceived work-related stress reported more alcohol consumption, a history of hyperlipidemia, and a higher prevalence of self-reported neck pain, poor sleep, and mild/moderate/severe depression. In our primary multivariate risk model to determine lifestyle and work-related stress variables and HRQoL, perceived work-related stress and a feeling of depression negatively impacted both the Physical Component Summary (PCS and Mental Component Summary (MCS scores of the SF-36 health survey. Hyperlipidemia and self-reported neck pain were associated with significantly lower PCS scores, whereas cardiovascular disease, gastric ulcer, and poor sleep were associated with statistically lower MCS scores. White-collar migrant workers are generally younger with high socioeconomic status. Perceived work-related stress and a feeling of depression indirectly affect HRQoL. Hyperlipidemia, self-reported neck pain, cardiovascular disease, gastric ulcer, and poor sleep also had a significant negative impact on HRQoL.

Effects of pulse ON and OFF time and electrode types on the material removal rate and tool wear rate of the Ti-6Al-4V Alloy using EDM machining with reverse polarity

Science.gov (United States)

Praveen, L.; Geeta Krishna, P.; Venugopal, L.; Prasad, N. E. C.

2018-03-01

Electrical Discharge Machining (EDM) is an unconventional metal removal process that is extensively used for removing the difficult-to-machine metal such as Ti alloys, super alloys and metal matrix composites. This paper investigates the effects of pulse (ON/OFF) time on EDM machining characteristics of Ti-6Al-4V alloy using copper and graphite as electrodes in reverse polarity condition. Full factorial design method was used to design the experiments. Two variables (Pulse On and OFF) with three levels are considered. The output variables are the tool wear rate and the material removal rate. The important findings from the present work are: (1) the material removal rate (MRR) increases gradually with an increase of the Pulse ON time whereas the change is insignificant with an increase of the Pulse OFF time, (2) Between copper and graphite electrodes, the copper electrode is proved to be good in terms of MRR, (3) a combination of high pulse ON time and OFF time is desirable for high MRR rate in the Cu electrode whereas for the graphite electrode, a combination of high pulse ON time and low pulse OFF time is desirable for high MRR rate, (4) the tool wear rate (TWR) reduces with the Pulse On or OFF time, the rate of TWR is uniform for the graphite electrode in contrast to abrupt decrease from 25 to 50 μs (pulse ON time) in the copper electrode, (5) In order to keep the TWR as minimum possible, it is desirable to have a combination of high pulse ON time and OFF time for both the copper and the graphite electrode.

Hair removal in adolescence

Directory of Open Access Journals (Sweden)

Sandra Pereira

2015-06-01

Full Text Available Introduction: Due to hormonal stimulation during puberty, changes occur in hair type and distribution. In both sexes, body and facial unwanted hair may have a negative psychological impact on the teenager. There are several available methods of hair removal, but the choice of the most suitable one for each individual can raise doubts. Objective: To review the main methods of hair removal and clarify their indications, advantages and disadvantages. Development: There are several removal methods currently available. Shaving and depilation with chemicals products are temporary methods, that need frequent repetition, because hair removal is next to the cutaneous surface. The epilating methods in which there is full hair extraction include: epilation with wax, thread, tweezers, epilating machines, laser, intense pulsed light, and electrolysis. Conclusions: The age of beginning hair removal and the method choice must be individualized and take into consideration the skin and hair type, location, dermatological and endocrine problems, removal frequency, cost and personal preferences.

Using Collar worn Sensors to Forecast Thermal Strain in Military Working Dogs

Science.gov (United States)

2016-04-22

Using Collar-worn Sensors to Forecast Thermal Strain in Military Working Dogs James R. Williamson, Austin R. Hess, Christopher J. Smalt, Delsey M...these estimates for forecasting and monitoring thermal strain is assessed based on performance in out of sample prediction of core temperature (Tc...time step (100 Hz) from the magnitude of the three- dimensional acceleration vector, ai , which is independent of sensor orientation. Next, the

Reactor refueling machine simulator

International Nuclear Information System (INIS)

Rohosky, T.L.; Swidwa, K.J.

1987-01-01

This patent describes in combination: a nuclear reactor; a refueling machine having a bridge, trolley and hoist each driven by a separate motor having feedback means for generating a feedback signal indicative of movement thereof. The motors are operable to position the refueling machine over the nuclear reactor for refueling the same. The refueling machine also has a removable control console including means for selectively generating separate motor signals for operating the bridge, trolley and hoist motors and for processing the feedback signals to generate an indication of the positions thereof, separate output leads connecting each of the motor signals to the respective refueling machine motor, and separate input leads for connecting each of the feedback means to the console; and a portable simulator unit comprising: a single simulator motor; a single simulator feedback signal generator connected to the simulator motor for generating a simulator feedback signal in response to operation of the simulator motor; means for selectively connecting the output leads of the console to the simulator unit in place of the refueling machine motors, and for connecting the console input leads to the simulator unit in place of the refueling machine motor feedback means; and means for driving the single simulator motor in response to any of the bridge, trolley or hoist motor signals generated by the console and means for applying the simulator feedback signal to the console input lead associated with the motor signal being generated by the control console

Effects of Collar Permeability on the Field Quality of the Large Aperture Quadrupoles for the LHC

CERN Document Server

Catalan-Lasheras, N; Kirby, G; Mess, K H; Ostojic, R; Russenschuck, Stephan

2008-01-01

The LHC contains a number of large aperture quadrupoles (MQY) in the insertions. The acceptance of these magnets was based on warm magnetic measurements performed before delivery to CERN. During the series production of the MQY quadrupoles, the permeability of the collars drifted from the nominal value, and effects on the transfer function and multipole components became evident. To study the effects on the magnetic field, variable permeability of the stainless-steel collars as a function of local field and temperature was introduced into a numerical model. Comparing the results with measured data, we could isolate the contribution of permeability deviation on the magnetic field quality. The extrapolation of transfer function and field multipoles to operating temperature and current gives the necessary offsets, which are compared with measurements on a reduced set of magnets.

A prospective cohort study on severe pain as a risk factor for long-term sickness absence in blue- and white-collar workers

DEFF Research Database (Denmark)

Andersen, Lars Louis; Mortensen, Ole Steen; Hansen, Jørgen Vinsløv

2011-01-01

Objective To estimate the impact of pain in different body regions on future long-term sickness absence (LTSA) among blue- and white-collar workers. Method Prospective cohort study in a representative sample of 5603 employees (the Danish Work Environment Cohort Study) interviewed in 2000, and fol......Objective To estimate the impact of pain in different body regions on future long-term sickness absence (LTSA) among blue- and white-collar workers. Method Prospective cohort study in a representative sample of 5603 employees (the Danish Work Environment Cohort Study) interviewed in 2000...... consecutive weeks. Age, gender, body mass index, smoking and diagnosed disease were controlled for. Results In 2000 the prevalence among blue- and white-collar workers, respectively, of severe pain was 33% and 29% (neck/shoulder), 33% and 25% (low back), 16% and 11% (hand/wrists), and 16% and 12% (knees......). During 2001-2002, the prevalence of LTSA among blue- and white-collar workers was 18% and 12%, respectively. Hand/wrist pain (HR 1.49, 95% CI 1.23 to 1.81) and low back pain (HR 1.30, 95% CI 1.11 to 1.53) were significant risk factors among the total cohort. Neck/shoulder pain was a significant risk...

Machinability of a Stainless Steel by Electrochemical Discharge Microdrilling

International Nuclear Information System (INIS)

Coteata, Margareta; Pop, Nicolae; Slatineanu, Laurentiu; Schulze, Hans-Peter; Besliu, Irina

2011-01-01

Due to the chemical elements included in their structure for ensuring an increased resistance to the environment action, the stainless steels are characterized by a low machinability when classical machining methods are applied. For this reason, sometimes non-traditional machining methods are applied, one of these being the electrochemical discharge machining. To obtain microholes and to evaluate the machinability by electrochemical discharge microdrilling, test pieces of stainless steel were used for experimental research. The electrolyte was an aqueous solution of sodium silicate with different densities. A complete factorial plan was designed to highlight the influence of some input variables on the sizes of the considered machinability indexes (electrode tool wear, material removal rate, depth of the machined hole). By mathematically processing of experimental data, empirical functions were established both for stainless steel and carbon steel. Graphical representations were used to obtain more suggestive vision concerning the influence exerted by the considered input variables on the size of the machinability indexes.

Fundamental investigation on influence of external heat on chip formation during thermal assisted machining

Science.gov (United States)

Alkali, A. U.; Ginta, T. L.; Abdulrani, A. M.; Elsiti, N. M.

2018-04-01

Various heat sources have been investigated by numerous researchers to reveal machinability benefits of thermally assisted machining (TAM) process. Fewer engineering materials have been tested. In the same vein, those researches continue to demonstrate effective performance of TAM in terms of bulk material removal rate, improved surface finish, prolong tool life and reduction of cutting forces among others. Experimental investigation on the strain-hardenability and flow stress of material removed with respect to increase in temperature in TAM has not been given attention in previous studies. This study investigated the pattern of chip morphology and segmentation giving close attention to influence of external heat source responsible for strain – hardenability of the material removed during TAM and dry machining at room temperature. Full immersion down cut milling was used throughout the machining conditions. Machining was conducted on AISI 316L using uncoated tungsten carbide end mill insert at varying cutting speeds (V) of 50, 79, and 100 m/min, and feed rates (f) of 0.15, 0.25, and 0.4 mm/tooth while the depth of cut was maintained at 0.2mm throughout the machining trials. The analyses of chip formation, segmentations and stain hardenability were carried out by using LMU light microscope, field emission microscopy and micro indentation. The study observed that build up edge is formed when a stagnation zone develops in front of tool tip which give rise to poor thermal gradient for conduction heat to be transferred within the bulk material during dry machining. This promotes varying strain – hardening of the material removed with evident high chips hardness and thickness, whereas TAM circumvents such impairment by softening the shear zone through local preheat.

Effect Of Pressure Support Versus Unassisted Breathing Through A Tracheostomy Collar On Weaning Duration In Patients Requiring Prolonged Mechanical Ventilation: A Randomized Trial

Science.gov (United States)

Jubran, Amal; Grant, Brydon J.B.; Duffner, Lisa A.; Collins, Eileen G.; Lanuza, Dorothy M.; Hoffman, Leslie A.; Tobin, Martin J.

2013-01-01

Context Patients requiring prolonged mechanical ventilation (more than 21 days) are commonly weaned at long-term acute care hospitals (LTACHs). The most effective method of weaning such patients has not been investigated. Objective To compare weaning duration with pressure support versus unassisted breathing through a tracheostomy (trach collar) in patients transferred to a LTACH for weaning from prolonged ventilation. Design, Settings, and Participants Between 2000 and 2010, a randomized study was conducted in tracheotomized patients transferred to a single LTACH for weaning from prolonged ventilation. Of 500 patients who underwent a five-day screening procedure, 316 failed and were randomly assigned to wean with pressure support (n=155) or a trach collar (n=161). Six- and twelve-month survival was also determined. Main outcome measure Primary outcome was weaning duration. Secondary outcome was survival at six and twelve months after enrollment. Results Of 316 patients, four were withdrawn and not included in analysis. Of 152 patients in the pressure-support arm, 68 (44.7%) were weaned; 22 (14.5%) died. Of 160 patients in the trach-collar arm, 85 (53.1%) were weaned; 16 (10.0%) died. Median weaning time was shorter with trach collar than with pressure support: 15 [interquartile range, 8–25] versus 19 [12–31] days, p=0.004. The hazard ratio (HR) for successful weaning rate was higher with trach collar than with pressure support (HR, 1.43; 95% confidence interval [CI], 1.03–1.98, p<0.03) after adjusting for baseline clinical covariates. Trach collar achieved faster weaning than did pressure support among subjects who failed the screening procedure at 12–120 hours (HR, 3.33; 95% CI, 1.44–7.70, p<0.01), whereas weaning time was equivalent with the two methods in patients who failed the screening procedure within 0–12 hours. Mortality was equivalent in the pressure-support and trach-collar arms at six months (55.9% versus 51.3%; 4.7 difference, 95% CI −6

Effect of pressure support vs unassisted breathing through a tracheostomy collar on weaning duration in patients requiring prolonged mechanical ventilation: a randomized trial.

Science.gov (United States)

Jubran, Amal; Grant, Brydon J B; Duffner, Lisa A; Collins, Eileen G; Lanuza, Dorothy M; Hoffman, Leslie A; Tobin, Martin J

2013-02-20

Patients requiring prolonged mechanical ventilation (>21 days) are commonly weaned at long-term acute care hospitals (LTACHs). The most effective method of weaning such patients has not been investigated. To compare weaning duration with pressure support vs unassisted breathing through a tracheostomy collar in patients transferred to an LTACH for weaning from prolonged ventilation. Between 2000 and 2010, a randomized study was conducted in tracheotomized patients transferred to a single LTACH for weaning from prolonged ventilation. Of 500 patients who underwent a 5-day screening procedure, 316 did not tolerate the procedure and were randomly assigned to receive weaning with pressure support (n = 155) or a tracheostomy collar (n = 161). Survival at 6- and 12-month time points was also determined. Primary outcome was weaning duration. Secondary outcome was survival at 6 and 12 months after enrollment. Of 316 patients, 4 were withdrawn and not included in analysis. Of 152 patients in the pressure-support group, 68 (44.7%) were weaned; 22 (14.5%) died. Of 160 patients in the tracheostomy collar group, 85 (53.1%) were weaned; 16 (10.0%) died. Median weaning time was shorter with tracheostomy collar use (15 days; interquartile range [IQR], 8-25) than with pressure support (19 days; IQR, 12-31), P = .004. The hazard ratio (HR) for successful weaning rate was higher with tracheostomy collar use than with pressure support (HR, 1.43; 95% CI, 1.03-1.98; P = .033) after adjusting for baseline clinical covariates. Use of the tracheostomy collar achieved faster weaning than did pressure support among patients who did not tolerate the screening procedure between 12 and 120 hours (HR, 3.33; 95% CI, 1.44-7.70; P = .005), whereas weaning time was equivalent with the 2 methods in patients who did not tolerate the screening procedure within 0 to 12 hours. Mortality was equivalent in the pressure-support and tracheostomy collar groups at 6 months (55.92% vs 51.25%; 4.67% difference, 95

Nutrient removal by apple, pear and cherry nursery trees

Directory of Open Access Journals (Sweden)

Giovambattista Sorrenti

2017-06-01

Full Text Available Given that nursery is a peculiar environment, the amount of nutrients removed by nursery trees represents a fundamental acquisition to optimise fertilisation strategies, with economic and environmental implications. In this context, we determined nutrient removal by apple, pear and cherry nursery trees at the end of the nursery growing cycle. We randomly removed 5 leafless apple (Golden Delicious/EMLA M9; density of 30,000 trees ha–1, pear (Santa Maria/Adams; density of 30,000 trees ha–1 and cherry (AlexTM/Gisela 6®; density of 40,000 trees ha–1 trees from a commercial nursery. Trees were divided into roots (below the root collar, rootstock (above-ground wood between root collar and grafting point and variety (1-year-old wood above the grafting point. For each organ we determined biomass, macro- (N, P, K, Ca, Mg, S, and micro- (Fe, Mn, Zn, Cu, and B nutrient concentration. Pear trees were the most developed (650 g (dw tree–1, equal to 1.75 and 2.78 folds than apple and cherry trees, respectively whereas, independently of the species, variety mostly contributed (>50% to the total tree biomass, followed by roots and then above-ground rootstock. However, the dry biomass and nutrient amount measured in rootstocks (including roots represent the cumulative amount of 2 and 3 seasons, for Gisela® 6 (tissue culture and pome fruit species (generated by mound layering, respectively. Macro and micronutrients were mostly concentrated in roots, followed by variety and rootstock, irrespective of the species. Independently of the tissue, macronutrients concentration hierarchy was N>Ca>K> P>Mg>S. Removed N by whole tree accounted for 6.58, 3.53 and 2.49 g tree–1 for pear, apple and cherry, respectively, corresponding to almost 200, 107 and 100 kg N ha–1, respectively. High amounts of K and Ca were used by pear (130-140 kg ha–1 and apple trees (~50 and 130 kg ha–1 of K and Ca, respectively, while ~25 kg K ha–1 and 55 kg Ca ha–1 were

Cleaning, disassembly, and requalification of the FFTF in vessel handling machine

International Nuclear Information System (INIS)

Coops, W.J.

1977-10-01

The Engineering Model In Vessel Handling Machine (IVHM) was successfully removed, cleaned, disassembled, inspected, reassembled and reinstalled into the sodium test vessel at Richland, Washington. This was the first time in the United States a full size operational sodium wetted machine has been cleaned by the water vapor nitrogen process and requalified for operation. The work utilized an atmospheric control system during removal, a tank type water vapor nitrogen cleaning system and an open ''hands on'' disassembly and assembly stand. Results of the work indicate the tools, process and equipment are adequate for the non-radioactive maintenance sequence. Additionally, the work proves that a machine of this complexity can be successfully cleaned, maintained and re-used without the need to replace a large percentage of the sodium wetted parts

“Investigations on the machinability of Waspaloy under dry environment”

Science.gov (United States)

Deepu, J.; Kuppan, P.; SBalan, A. S.; Oyyaravelu, R.

2016-09-01

Nickel based superalloy, Waspaloy is extensively used in gas turbine, aerospace and automobile industries because of their unique combination of properties like high strength at elevated temperatures, resistance to chemical degradation and excellent wear resistance in many hostile environments. It is considered as one of the difficult to machine superalloy due to excessive tool wear and poor surface finish. The present paper is an attempt for removing cutting fluids from turning process of Waspaloy and to make the processes environmentally safe. For this purpose, the effect of machining parameters such as cutting speed and feed rate on the cutting force, cutting temperature, surface finish and tool wear were investigated barrier. Consequently, the strength and tool wear resistance and tool life increased significantly. Response Surface Methodology (RSM) has been used for developing and analyzing a mathematical model which describes the relationship between machining parameters and output variables. Subsequently ANOVA was used to check the adequacy of the regression model as well as each machining variables. The optimal cutting parameters were determined based on multi-response optimizations by composite desirability approach in order to minimize cutting force, average surface roughness and maximum flank wear. The results obtained from the experiments shown that machining of Waspaloy using coated carbide tool with special ranges of parameters, cutting fluid could be completely removed from machining process

Operating a pneumatic-mechanical flotation machine for coal-slurry flotation

Energy Technology Data Exchange (ETDEWEB)

Shmaenok, N M; Bedran, N G; Konstantinov, V K; Kochetkov, Yu I; Sysoev, V S

1976-01-01

The FPM-GMO-1.6 pneumatic-mechanical flotation machine is easy to operate and regulate and maintains a high throughput at a low energy consumption. The flotation process is stable, the quality of the concentrate and tailings satisfactory, and the selectivity of separation high. The machine cannot handle coal slurries at higher throughputs because the rate of froth removal is too low across the entire flotation front. Experience on the pneumatic-mechanical flotation machine at the ''Kolosnikovskaya'' Central Washery indicates that a similar machine should be developed for a throughput of 1000 m/sup 3//hr.

Pressure ulcers, indentation marks and pain from cervical spine immobilization with extrication collars and headblocks: An observational study.

Science.gov (United States)

Ham, Wietske H W; Schoonhoven, Lisette; Schuurmans, Marieke J; Leenen, Luke P H

2016-09-01

To describe the occurrence and severity of pressure ulcers, indentation marks and pain from the extrication collar combined with headblocks. Furthermore, the influence of time, injury severity and patient characteristics on the development of pressure ulcers, indentation marks and pain was explored. Observational. Level one trauma centre in the Netherlands. Adult trauma patients admitted to the Emergency Department in an extrication collar combined with headblocks. Between January and December 2013, 342 patients were included. Study outcomes were incidence and severity of pressure ulcers, indentation marks and pain. The following dependent variables were collected: time in the cervical collar and headblocks, Glasgow Coma Scale, Mean Arterial Pressure, haemoglobin, Injury Severity Score, gender, age, and Body Mass Index. 75.4% of the patients developed a category 1 and 2.9% a category 2 pressure ulcer. Indentation marks were observed in 221 (64.6%) patients; 96 (28.1%) had severe indentation marks. Pressure ulcers and indentation marks were observed most frequently at the back, shoulders and chest. 63.2% experienced pain, of which, 38.5% experienced severe pain. Pain was mainly located at the occiput. Female patients experienced significantly more pain (NRS>3) compared to male patients (OR=2.14, 95% CI 1.21-3.80) None of the investigated variables significantly increased the probability of developing PUs or indentation marks. The high incidence of category 1 pressure ulcers and severe indentation marks indicate an increased risk for pressure ulcer development and may well lead to more severe PU lesions. Pain due to the application of the extrication collar and headblocks may lead to undesirable movement (in order to relieve the pressure) or to bias clinical examination of the cervical spine. It is necessary to revise the current practice of cervical spine immobilization. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cervical collar or physiotherapy versus wait and see policy for recent onset cervical radiculopathy: randomised trial.

NARCIS (Netherlands)

B. Kuijper (Barbara); J.T. Tans; A. Beelen (Anita); F. Nollet (Frans); M. de Visser (Marianne)

2009-01-01

textabstractOBJECTIVE: To evaluate the effectiveness of treatment with collar or physiotherapy compared with a wait and see policy in recent onset cervical radiculopathy. DESIGN: Randomised controlled trial. SETTING: Neurology outpatient clinics in three Dutch hospitals. PARTICIPANTS: 205 patients

Blue-Collar Affluence in a Remote Mining Town: Challenging the Modernist Myth of Education

Science.gov (United States)

Forsey, Martin

2015-01-01

Based on research in Karratha, a remote resource town in Western Australia, this paper explores the ways in which blue-collar affluence disturbs the meritocratic mythology of formal education. In the opening decade of the twenty-first century Karratha was one of Australia's most affluent towns, yet its adult population was characterised by a level…

Cervical collar or physiotherapy versus wait and see policy for recent onset cervical radiculopathy: randomised trial

NARCIS (Netherlands)

Kuijper, Barbara; Tans, Jos Th J.; Beelen, Anita; Nollet, Frans; de Visser, Marianne

2009-01-01

Objective To evaluate the effectiveness of treatment with collar or physiotherapy compared with a wait and see policy in recent onset cervical radiculopathy. Design Randomised controlled trial. Setting Neurology outpatient clinics in three Dutch hospitals. Participants 205 patients with symptoms and

Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

Directory of Open Access Journals (Sweden)

Amitesh Goswami

2017-02-01

Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

Design of an ultraprecision computerized numerical control chemical mechanical polishing machine and its implementation

Science.gov (United States)

Zhang, Chupeng; Zhao, Huiying; Zhu, Xueliang; Zhao, Shijie; Jiang, Chunye

2018-01-01

The chemical mechanical polishing (CMP) is a key process during the machining route of plane optics. To improve the polishing efficiency and accuracy, a CMP model and machine tool were developed. Based on the Preston equation and the axial run-out error measurement results of the m circles on the tin plate, a CMP model that could simulate the material removal at any point on the workpiece was presented. An analysis of the model indicated that lower axial run-out error led to lower material removal but better polishing efficiency and accuracy. Based on this conclusion, the CMP machine was designed, and the ultraprecision gas hydrostatic guideway and rotary table as well as the Siemens 840Dsl numerical control system were incorporated in the CMP machine. To verify the design principles of machine, a series of detection and machining experiments were conducted. The LK-G5000 laser sensor was employed for detecting the straightness error of the gas hydrostatic guideway and the axial run-out error of the gas hydrostatic rotary table. A 300-mm-diameter optic was chosen for the surface profile machining experiments performed to determine the CMP efficiency and accuracy.

Method of vertically and horizontally cutting steel pipe piles and removing them based on the development of a steel pipe pile vertically cutting machine; Kokanko tatehoko setsudanki no kaihatsu ni yoru kochi chubu no juo setsudan tekkyo koho

Energy Technology Data Exchange (ETDEWEB)

Watanabe, S.; Takeshita, A.; Kobayashi, K.

1997-07-25

A machine for vertically cutting steel pipe piles has newly been developed for the purpose of removing the end portions the shore protection steel pipe piles which interfere with the shield tunneling work in the Ohokagawa River tunneling section on the Minato Mirai 21 Line. This paper reports the development of the machine for vertically cutting steel pipe piles, and a method of cutting the shield tunneling work hindering piles under the ground by using this machine. The obstacle-constituting portions of the piles are removed by destroying the copings, excavating the interior of the piles to make the same hollow so that a cutting machine can be inserted, and cutting the piles vertically and horizontally. The basic structure of the cutting machine comprises a lower cutting unit for making forward and backward and upward and downward movements of a cutter, and an upper movable unit for controlling the rotation of the cutting unit. The cutting of a pile is done by projecting the cutter by a cylinder the base of which is joined to a cutter driver, and then moving the rotating cutter upward. The amounts of movements of these parts are detected by sensors, and an arbitrary range of the underground portion of a pile can be cut by a remote control operation. 10 figs., 1 tab.

Causes and consequences of timing errors associated with global positioning system collar accelerometer activity monitors

Science.gov (United States)

Adam J. Gaylord; Dana M. Sanchez

2014-01-01

Direct behavioral observations of multiple free-ranging animals over long periods of time and large geographic areas is prohibitively difficult. However, recent improvements in technology, such as Global Positioning System (GPS) collars equipped with motion-sensitive activity monitors, create the potential to remotely monitor animal behavior. Accelerometer-equipped...

Exploring New York State Policy Expectations Pertaining to Energy Efficiency and Green Collar Workforce

Science.gov (United States)

Pauli, Felix Asher

2012-01-01

The Green Jobs Green New York (GJGNY) Act of 2009 was designed to reduce energy consumption by creating green collar workforce and providing energy efficiency audits to the public. The problem addressed in this study is the discrepancy between the expectations of Green Jobs Green New York Act of 2009 and the implementation of this policy. This…

Dynamic Material Removal Rate and Tool Replacement Optimization with Calculus of Variations

Science.gov (United States)

Lan, Tian-Syung; Lo, Chih-Yao; Chiu, Min-Chie; Yeh, Long-Jyi

This study mathematically presents an optimum material removal control model, where the Material Removal Rate (MRR) is comprehensively introduced, to accomplish the dynamic machining control and tool life determination of a cutting tool under an expected machining quantity. To resolve the incessant cutting-rate control problem, Calculus of Variations is implemented for the optimum solution. Additionally, the decision criteria for selecting the dynamic solution are suggested and the sensitivity analyses for key variables in the optimal solution are fully discussed. The versatility of this study is furthermore exemplified through a numerical illustration from the real-world industry with BORLAND C++ BUILDER. It is shown that the theoretical and simulated results are in good agreement. This study absolutely explores the very promising solution to dynamically organize the MRR in minimizing the machining cost of a cutting tool for the contemporary machining industry.

Surface and subsurface cracks characteristics of single crystal SiC wafer in surface machining

Energy Technology Data Exchange (ETDEWEB)

Qiusheng, Y., E-mail: qsyan@gdut.edu.cn; Senkai, C., E-mail: senkite@sina.com; Jisheng, P., E-mail: panjisheng@gdut.edu.cn [School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou, 510006 (China)

2015-03-30

Different machining processes were used in the single crystal SiC wafer machining. SEM was used to observe the surface morphology and a cross-sectional cleavages microscopy method was used for subsurface cracks detection. Surface and subsurface cracks characteristics of single crystal SiC wafer in abrasive machining were analysed. The results show that the surface and subsurface cracks system of single crystal SiC wafer in abrasive machining including radial crack, lateral crack and the median crack. In lapping process, material removal is dominated by brittle removal. Lots of chipping pits were found on the lapping surface. With the particle size becomes smaller, the surface roughness and subsurface crack depth decreases. When the particle size was changed to 1.5µm, the surface roughness Ra was reduced to 24.0nm and the maximum subsurface crack was 1.2µm. The efficiency of grinding is higher than lapping. Plastic removal can be achieved by changing the process parameters. Material removal was mostly in brittle fracture when grinding with 325# diamond wheel. Plow scratches and chipping pits were found on the ground surface. The surface roughness Ra was 17.7nm and maximum subsurface crack depth was 5.8 µm. When grinding with 8000# diamond wheel, the material removal was in plastic flow. Plastic scratches were found on the surface. A smooth surface of roughness Ra 2.5nm without any subsurface cracks was obtained. Atomic scale removal was possible in cluster magnetorheological finishing with diamond abrasive size of 0.5 µm. A super smooth surface eventually obtained with a roughness of Ra 0.4nm without any subsurface crack.

Removable top nozzle and tool for a nuclear reactor fuel assembly

International Nuclear Information System (INIS)

Wilson, J.F.; Cerni, S.; Gjertsen, R.K.

1986-01-01

A fuel assembly is described for a nuclear reactor including a bottom nozzle, at least one longitudinally extending control rod guide thimble having an upper end and a lower end being attached to the bottom nozzle and projecting upwardly therefrom, transverse grids axially spaced along-the thimble for supporting an array of upstanding fuel rods, and a top nozzle subassembly removable mounted on the upper end of the guide thimble for obtaining top access to the fuel rods upon removal thereof. The top nozzle subassembly consists of: (a) a section integrally formed on the upper end of the guide thimble and having external threads thereon; (b) a lower adapter plate having a guide thimble hole for receiving the guide thimble so as to mount the adapter plate on the guide thimble for slidable movement therealong; (c) a retainer mounted on the guide thimble for restably supporting and limiting the downward movement of the adapter plate along the guide thimble; (d) an upper hold-down plate having a guide thimble passageway with an internal ledge for receiving the thimble so as to mount the hold-down plate on the thimble for slidable movement therealong; (e) spring means interposed between the upper hold-down plate and the lower adapter plate for biasing the hold-down plate upwardly when a downward force is applied thereon whereby the downward force is yieldably transmitted to the fuel assembly; and (f) a collar disposed within the passageway and in abutment with the ledge, the collar having an internal threaded section engageable with the externally threaded section to move the hold-down plate down against the spring means and thereby mounting of the subassembly on the guide thimble

Prolonged Sitting is Associated with Attenuated Heart Rate Variability during Sleep in Blue-Collar Workers

Directory of Open Access Journals (Sweden)

David M Hallman

2015-11-01

Full Text Available Prolonged sitting is associated with increased risk for cardiovascular diseases and mortality. However, research into the physiological determinants underlying this relationship is still in its infancy. The aim of the study was to determine the extent to which occupational and leisure-time sitting are associated with nocturnal heart rate variability (HRV in blue-collar workers. The study included 138 blue-collar workers (mean age 45.5 (SD 9.4 years. Sitting-time was measured objectively for four days using tri-axial accelerometers (Actigraph GT3X+ worn on the thigh and trunk. During the same period, a heart rate monitor (Actiheart was used to sample R-R intervals from the electrocardiogram. Time and frequency domain indices of HRV were only derived during nighttime sleep, and used as markers of cardiac autonomic modulation. Regression analyses with multiple adjustments (age, gender, body mass index, smoking, job-seniority, physical work-load, influence at work, and moderate-to-vigorous physical activity were used to investigate the association between sitting time and nocturnal HRV. We found that occupational sitting-time was negatively associated (p < 0.05 with time and frequency domain HRV indices. Sitting-time explained up to 6% of the variance in HRV, independent of the covariates. Leisure-time sitting was not significantly associated with any HRV indices (p > 0.05. In conclusion, objectively measured occupational sitting-time was associated with reduced nocturnal HRV in blue-collar workers. This indicates an attenuated cardiac autonomic regulation with increasing sitting-time at work regardless of moderate-to-vigorous physical activity. The implications of this association for cardiovascular disease risk warrant further investigation via long-term prospective studies and intervention studies.

Design of on-power fuelling machines

International Nuclear Information System (INIS)

Jackson, W.H.

2004-01-01

In May 1957, CGE was asked to design a fuelling machine for NPD2 Reactor. Two fuelling machines were required, one at each end of the reactor, that could either push the fuel bundles through the reactor or accept the bundles being pushed out. The machines had to connect on to the end fittings of the same tube, seal, fill with heavy water and pressure up to 1000 psi without external leaks. Each machine had to remove the tube seal plug from its end fitting and store it in an indexing magazine, which also had to hold up to six fuel bundles, or retrieve that many, if the magazine was empty. There was also the provision to store a spare plug. When finished moving fuel bundles, the tube plugs were to be replaced and tested for leaks, before the fuelling machines would be detached from the end fittings. This was all to be done by remote control. By late September 1957, sufficient design features were on paper and CGE management made a presentation to AECL at Chalk River Laboratories and this proposal was later accepted

Flushing Enhancement with Vibration and Pulsed Current in Electrochemical Machining

Directory of Open Access Journals (Sweden)

Zhujian Feng

2017-12-01

Full Text Available This research aims to understand flushing of by-products in electrochemical machining (ECM by modeling and experimentally verifying mechanism of particle transport in inter-electrode gap under low frequency vibration. A series of hole were drilled on steel plates to evaluate the effect of vibration on material removal rate and hole quality. Infinite focus optical technique was used to capture and analyze the three-dimensional images of ECM'ed features. Experimental results showed that maximum machining depth and minimum taper angle can be achieved when vibrating the workpiece at 40 Hz and 10 µm amplitude. Simulation results showed that the highest average flushing speed of 0.4 m/s was obtained at this vibration frequency and amplitude. Machining depth and material removal rate has a positive correlation with the average flushing speed. Sharper ECM’ed profile is obtained since the taper angle is favorably reduced at high average flushing speed.

Efficient bounding schemes for the two-center hybrid flow shop scheduling problem with removal times.

Science.gov (United States)

Hidri, Lotfi; Gharbi, Anis; Louly, Mohamed Aly

2014-01-01

We focus on the two-center hybrid flow shop scheduling problem with identical parallel machines and removal times. The job removal time is the required duration to remove it from a machine after its processing. The objective is to minimize the maximum completion time (makespan). A heuristic and a lower bound are proposed for this NP-Hard problem. These procedures are based on the optimal solution of the parallel machine scheduling problem with release dates and delivery times. The heuristic is composed of two phases. The first one is a constructive phase in which an initial feasible solution is provided, while the second phase is an improvement one. Intensive computational experiments have been conducted to confirm the good performance of the proposed procedures.

On non-permutation solutions to some two machine flow shop scheduling problems

NARCIS (Netherlands)

V. Strusevich (Vitaly); P.J. Zwaneveld (Peter)

1994-01-01

textabstractIn this paper, we study two versions of the two machine flow shop scheduling problem, where schedule length is to be minimized. First, we consider the two machine flow shop with setup, processing, and removal times separated. It is shown that an optimal solution need not be a permutation

COMPARISON OF STATISTICALLY CONTROLLED MACHINING SOLUTIONS OF TITANIUM ALLOYS USING USM

Directory of Open Access Journals (Sweden)

R. Singh

2010-06-01

Full Text Available The purpose of the present investigation is to compare the statistically controlled machining solution of titanium alloys using ultrasonic machining (USM. In this study, the previously developed Taguchi model for USM of titanium and its alloys has been investigated and compared. Relationships between the material removal rate, tool wear rate, surface roughness and other controllable machining parameters (power rating, tool type, slurry concentration, slurry type, slurry temperature and slurry size have been deduced. The results of this study suggest that at the best settings of controllable machining parameters for titanium alloys (based upon the Taguchi design, the machining solution with USM is statistically controlled, which is not observed for other settings of input parameters on USM.

A new fast neutron collar for safeguards inspection measurements of fresh low enriched uranium fuel assemblies containing burnable poison rods

Energy Technology Data Exchange (ETDEWEB)

Evans, Louise G., E-mail: evanslg@ornl.gov [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Swinhoe, Martyn T.; Menlove, Howard O. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Schwalbach, Peter; Baere, Paul De [European Commission, Euratom Safeguards Office (Luxembourg); Browne, Michael C. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

2013-11-21

Safeguards inspection measurements must be performed in a timely manner in order to detect the diversion of significant quantities of nuclear material. A shorter measurement time can increase the number of items that a nuclear safeguards inspector can reliably measure during a period of access to a nuclear facility. In turn, this improves the reliability of the acquired statistical sample, which is used to inform decisions regarding compliance. Safeguards inspection measurements should also maintain independence from facility operator declarations. Existing neutron collars employ thermal neutron interrogation for safeguards inspection measurements of fresh fuel assemblies. A new fast neutron collar has been developed for safeguards inspection measurements of fresh low-enriched uranium (LEU) fuel assemblies containing gadolinia (Gd{sub 2}O{sub 3}) burnable poison rods. The Euratom Fast Collar (EFC) was designed with high neutron detection efficiency to make a fast (Cd) mode measurement viable whilst meeting the high counting precision and short assay time requirements of the Euratom safeguards inspectorate. A fast mode measurement reduces the instrument sensitivity to burnable poison rod content and therefore reduces the applied poison correction, consequently reducing the dependence on the operator declaration of the poison content within an assembly. The EFC non-destructive assay (NDA) of typical modern European pressurized water reactor (PWR) fresh fuel assembly designs have been simulated using Monte Carlo N-particle extended transport code (MCNPX) simulations. Simulations predict that the EFC can achieve 2% relative statistical uncertainty on the doubles neutron counting rate for a fast mode measurement in an assay time of 600 s (10 min) with the available {sup 241}AmLi (α,n) interrogation source strength of 5.7×10{sup 4} s{sup −1}. Furthermore, the calibration range of the new collar has been extended to verify {sup 235}U content in variable PWR fuel

A new fast neutron collar for safeguards inspection measurements of fresh low enriched uranium fuel assemblies containing burnable poison rods

International Nuclear Information System (INIS)

Evans, Louise G.; Swinhoe, Martyn T.; Menlove, Howard O.; Schwalbach, Peter; Baere, Paul De; Browne, Michael C.

2013-01-01

Safeguards inspection measurements must be performed in a timely manner in order to detect the diversion of significant quantities of nuclear material. A shorter measurement time can increase the number of items that a nuclear safeguards inspector can reliably measure during a period of access to a nuclear facility. In turn, this improves the reliability of the acquired statistical sample, which is used to inform decisions regarding compliance. Safeguards inspection measurements should also maintain independence from facility operator declarations. Existing neutron collars employ thermal neutron interrogation for safeguards inspection measurements of fresh fuel assemblies. A new fast neutron collar has been developed for safeguards inspection measurements of fresh low-enriched uranium (LEU) fuel assemblies containing gadolinia (Gd 2 O 3 ) burnable poison rods. The Euratom Fast Collar (EFC) was designed with high neutron detection efficiency to make a fast (Cd) mode measurement viable whilst meeting the high counting precision and short assay time requirements of the Euratom safeguards inspectorate. A fast mode measurement reduces the instrument sensitivity to burnable poison rod content and therefore reduces the applied poison correction, consequently reducing the dependence on the operator declaration of the poison content within an assembly. The EFC non-destructive assay (NDA) of typical modern European pressurized water reactor (PWR) fresh fuel assembly designs have been simulated using Monte Carlo N-particle extended transport code (MCNPX) simulations. Simulations predict that the EFC can achieve 2% relative statistical uncertainty on the doubles neutron counting rate for a fast mode measurement in an assay time of 600 s (10 min) with the available 241 AmLi (α,n) interrogation source strength of 5.7×10 4 s −1 . Furthermore, the calibration range of the new collar has been extended to verify 235 U content in variable PWR fuel designs in the presence of up to

Machinability studies of infrared window materials and metals

International Nuclear Information System (INIS)

Arnold, J.B.; Morris, T.O.; Sladky, R.E.; Steger, P.J.

1976-01-01

Diamond machining of materials for optical applications is becoming an important fabrication process. Development work in material-removal technology to better understand the mechanics of the diamond-turning process, its limitations, and applications is described. The technique is presently limited to a select group of metals, most of which are of a face-center-cubic crystal structure. Machinability studies were done which were designed to better understand diamond compatibility and thus expand the range of applicable materials. Nonconventional methods such as ultrasonic tool stimulation were investigated. Work done to determine the machinability of infrared window materials indicates that this is a viable fabrication technique for many materials, although additional effort is needed to optimize the process for particular materials

Association between long working hours and sleep problems in white-collar workers.

Science.gov (United States)

Nakashima, Motoko; Morikawa, Yuko; Sakurai, Masaru; Nakamura, Koshi; Miura, Katsuyuki; Ishizaki, Masao; Kido, Teruhiko; Naruse, Yuchi; Suwazono, Yasushi; Nakagawa, Hideaki

2011-03-01

The purpose of this study is to examine the association between long work hours and sleep disturbance among white-collar workers. We evaluated 1510 male white-collar full-time employees, between the ages of 18 and 59 years, using a comprehensive sleep quality questionnaire, the Pittsburgh Sleep Quality Index (PSQI). All subjects worked in a light metal products factory in Japan. The mean number of monthly overtime work hours was determined using data from the previous 6 months from timecard records. Subjects were divided into five groups based on quintiles of the mean number of monthly overtime work hours: 63. Leisure time physical activity, drinking habits just before sleep, presence of family/partner and health status were used as confounding factors in the multiple regression model. The prevalence of short sleep hours, impairment of sleep efficiency and daytime dysfunction among seven components of PSQI increased, in a dose-response relationship, with overtime work hours. The prevalence of high global score (>5.5 points) was highest in workers with overtime hours ≥50 h week(-1). The odds ratios after adjustment for confounding factors for high global score using less than 26 h as a reference group were 1.67 for workers with ≥50 h and long work hours correlate with reduced sleep quality in a dose-response manner. © 2010 European Sleep Research Society.

Histology of palate and soft palate tonsil of collared peccary (Tayassu tajacu).

Science.gov (United States)

Teófilo, T S; Morais, M R P T; Dias, G F; Diniz, A N; Chaves, H S A; Fontenele-Neto, J D

2014-10-01

Peccaries are characterized by a prominent skin gland, known as scent gland, which is located in the middle of the rump. These animals are able to survive in a great variety of habitats, from humid tropical forests to semi-arid areas. They are omnivorous animals, and their diet includes fibrous material, vegetables, fruits, small vertebrates and insects. Collared peccary hard palate and soft palate tonsils were studied, macroscopic morphometric data were collected and tissue samples were paraffin-embedded. Sections were stained with HE, Gomori's trichrome and von Kossa; the first two were used to study general organization and the latter to detect calcium deposits. The hard palate showed one incisive papilla followed by several rugae united by a distinct raphe. The hard palate is lined by a keratinised squamous epithelium resting on a dense connective, whereas in the soft palate, the epithelium is parakeratinised and showed lymphocyte infiltration. The palate showed several pacinian corpuscles in the propria-submucosa. Two ovoid-shaped tonsils were found in the soft palate, and several crypts were observed on its surface. The epithelium was highly infiltrated by lymphocytes, and within the crypts, tonsilloliths were frequently observed. The study showed that the general organization of collared peccary palate is similar to other species, but in its oropharynx, only the soft palate tonsil was present and the pacinian corpuscles formed small aggregates. © 2013 Blackwell Verlag GmbH.

Design, Construction and Evaluation of a Row Crop Thinning Machine

Directory of Open Access Journals (Sweden)

M Gol Mohammadi

2014-04-01

Full Text Available Equipment availability is necessary in the development of Agriculture mechanization. Crop thinning is one of the most important stages in row crop production which is laborious and costly. The objective of this project is design and construction of a row crop thinning machine. Four main system units are plant sensors, ground sensors, control and thinning platforms. In this machine the unwanted plants on the rows are randomly removed by employing a pneumatically system. A blade on a vertical arm with pendulum motion removes the plant from the rows. The machine control system consists of an arm and a blade which is activated by a double acting cylinder and equipped with a relay and a timer. The pneumatic cylinder is controlled via a solenoid valve. Laboratory tests were conducted to validate the machine performance. Some other preliminary tests also were performed for optimization of parameters such as cinematic index and cutting length of blades. The laboratory tests (totally 9 tests were performed with a constant forward speed and three levels of plant density, using artificial plants. The data were analyzed using SPSS software. The results show that satisfactory performance of the machine is achieved when the plant density is moderate i.e. the thinning performance reduces with higher plant distance in the row. The other effective variable on machine performance is the adjustment of sensor sensitivity, which is used to distinguish between week and strong plants. In general the machine performance is sensitive to plant shape and morphology, plant distribution pattern in the field, growing stage of the plants, time of thinning and the effectiveness of previous weeding operations

Characterization of Contact and Bulk Thermal Resistance of Laminations for Electric Machines

Energy Technology Data Exchange (ETDEWEB)

Cousineau, J. Emily [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bennion, Kevin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); DeVoto, Doug [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mihalic, Mark [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Narumanchi, Sreekant [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2015-06-30

The ability to remove heat from an electric machine depends on the passive stack thermal resistances within the machine and the convective cooling performance of the selected cooling technology. This report focuses on the passive thermal design, specifically properties of the stator and rotor lamination stacks. Orthotropic thermal conductivity, specific heat, and density are reported. Four materials commonly used in electric machines were tested, including M19 (29 and 26 gauge), HF10, and Arnon 7 materials.

In vitro assessment of cutting efficiency and durability of zirconia removal diamond rotary instruments.

Science.gov (United States)

Kim, Joon-Soo; Bae, Ji-Hyeon; Yun, Mi-Jung; Huh, Jung-Bo

2017-06-01

Recently, zirconia removal diamond rotary instruments have become commercially available for efficient cutting of zirconia. However, research of cutting efficiency and the cutting characteristics of zirconia removal diamond rotary instruments is limited. The purpose of this in vitro study was to assess and compare the cutting efficiency, durability, and diamond rotary instrument wear pattern of zirconia diamond removal rotary instruments with those of conventional diamond rotary instruments. In addition, the surface characteristics of the cut zirconia were assessed. Block specimens of 3 mol% yttrium cation-doped tetragonal zirconia polycrystal were machined 10 times for 1 minute each using a high-speed handpiece with 6 types of diamond rotary instrument from 2 manufacturers at a constant force of 2 N (n=5). An electronic scale was used to measure the lost weight after each cut in order to evaluate the cutting efficiency. Field emission scanning electron microscopy was used to evaluate diamond rotary instrument wear patterns and machined zirconia block surface characteristics. Data were statistically analyzed using the Kruskal-Wallis test, followed by the Mann-Whitney U test (α=.05). Zirconia removal fine grit diamond rotary instruments showed cutting efficiency that was reduced compared with conventional fine grit diamond rotary instruments. Diamond grit fracture was the most dominant diamond rotary instrument wear pattern in all groups. All machined zirconia surfaces were primarily subjected to plastic deformation, which is evidence of ductile cutting. Zirconia blocks machined with zirconia removal fine grit diamond rotary instruments showed the least incidence of surface flaws. Although zirconia removal diamond rotary instruments did not show improved cutting efficiency compared with conventional diamond rotary instruments, the machined zirconia surface showed smoother furrows of plastic deformation and fewer surface flaws. Copyright © 2016 Editorial Council

Detecting Milling Deformation in 7075 Aluminum Alloy Aeronautical Monolithic Components Using the Quasi-Symmetric Machining Method

Directory of Open Access Journals (Sweden)

Qiong Wu

2016-04-01

Full Text Available The deformation of aeronautical monolithic components due to CNC machining is a bottle-neck issue in the aviation industry. The residual stress releases and redistributes in the process of material removal, and the distortion of the monolithic component is generated. The traditional one-side machining method will produce oversize deformation. Based on the three-stage CNC machining method, the quasi-symmetric machining method is developed in this study to reduce deformation by symmetry material removal using the M-symmetry distribution law of residual stress. The mechanism of milling deformation due to residual stress is investigated. A deformation experiment was conducted using traditional one-side machining method and quasi-symmetric machining method to compare with finite element method (FEM. The deformation parameters are validated by comparative results. Most of the errors are within 10%. The reason for these errors is determined to improve the reliability of the method. Moreover, the maximum deformation value of using quasi-symmetric machining method is within 20% of that of using the traditional one-side machining method. This result shows the quasi-symmetric machining method is effective in reducing deformation caused by residual stress. Thus, this research introduces an effective method for reducing the deformation of monolithic thin-walled components in the CNC milling process.

Long working hours and risk for hypertension in Japanese male white collar workers

OpenAIRE

Nakanishi, N; Yoshida, H; Nagano, K; Kawashimo, H; Nakamura, K; Tatara, K

2001-01-01

STUDY OBJECTIVE—To evaluate the association of long working hours with the risk for hypertension.
DESIGN—A five year prospective cohort study.
SETTING—Work site in Osaka, Japan.
PARTICIPANTS—941 hypertension free Japanese male white collar workers aged 35-54 years were prospectively examined by serial annual health examinations. Men in whom borderline hypertension and hypertension were found during repeated surveys were defined as incidental cases of borderline hypertension and hypertension.
...

Electrochemical machining of burn-resistant Ti40 alloy

Directory of Open Access Journals (Sweden)

Xu Zhengyang

2015-08-01

Full Text Available This study investigates the feasibility of using electrochemical machining (ECM to produce critical aeroengine components from a new burn-resistant titanium alloy (Ti40, thereby reducing costs and improving efficiency relative to conventional mechanical machining. Through this, it is found that an aqueous mix of sodium chloride and potassium bromide provides the optimal electrolyte and that the surface quality of the Ti40 workpiece is improved by using a pulsed current of 1 kHz rather than a direct current. Furthermore, the quality of cavities produced by ECM and the overall material removal rate are determined to be dependent on a combination of operating voltage, electrolyte inlet pressure, cathode feeding rate and electrolyte concentration. By optimizing these parameters, a surface roughness of 0.371 μm has been achieved in conjunction with a specific removal rate of more than 3.1 mm3/A·min.

Prognostic factors for respiratory sickness absence and return to work among blue collar workers and office personnel

NARCIS (Netherlands)

E.C. Alexopoulos (Evangelos); A. Burdorf (Alex)

2001-01-01

textabstractOBJECTIVES: To analyze factors that determine the occurrence of sickness absence due to respiratory disorders and the time it takes to return to work. METHODS: A longitudinal study with 2 year follow up was conducted among 326 male blue collar and white

First results of feral cats (Felis catus) monitored with GPS collars in New Zealand

CSIR Research Space (South Africa)

Recio, MR

2010-04-01

Full Text Available -monitoring of feral cats injection of 0.12?0.20 ml of Antisedan? (Atipamezone hydrochloride) reversed the effect of Domitor. Individuals were weighed, sexed and visually inspected, and fitted with a GPS data-logger collar (Sirtrack, Havelock North, NZ, http.... __________________________________________________________________________________________________________________________________________________________________ Sex Capture Tracking period No. of No. of potential Fix rate No. of fixes % of fixes date (days) fixes fixes percentage HDOP < 9 used...

PTFE bypass to below-knee arteries: distal vein collar or not? A prospective randomised multicentre study

DEFF Research Database (Denmark)

Lundgren, Fredrik; Bergqvist, David; Norgren, Lars

2010-01-01

Patency and limb salvage after synthetic bypass to the arteries below-knee are inferior to that which can be achieved with autologous vein. Use of a vein collar at the distal anastomosis has been suggested to improve patency and limb salvage, a problem that is analysed in this randomised clinical...

Investigation of roughing machining simulation by using visual basic programming in NX CAM system

Science.gov (United States)

Hafiz Mohamad, Mohamad; Nafis Osman Zahid, Muhammed

2018-03-01

This paper outlines a simulation study to investigate the characteristic of roughing machining simulation in 4th axis milling processes by utilizing visual basic programming in NX CAM systems. The selection and optimization of cutting orientation in rough milling operation is critical in 4th axis machining. The main purpose of roughing operation is to approximately shape the machined parts into finished form by removing the bulk of material from workpieces. In this paper, the simulations are executed by manipulating a set of different cutting orientation to generate estimated volume removed from the machine parts. The cutting orientation with high volume removal is denoted as an optimum value and chosen to execute a roughing operation. In order to run the simulation, customized software is developed to assist the routines. Operations build-up instructions in NX CAM interface are translated into programming codes via advanced tool available in the Visual Basic Studio. The codes is customized and equipped with decision making tools to run and control the simulations. It permits the integration with any independent program files to execute specific operations. This paper aims to discuss about the simulation program and identifies optimum cutting orientations for roughing processes. The output of this study will broaden up the simulation routines performed in NX CAM systems.

Removing roughness on metal surface by irradiation of intense short-pulsed ion beams

International Nuclear Information System (INIS)

Hashimoto, Y.

1995-01-01

Surface modification of metals with an intense pulsed ion beam (IPIB) was studied experimentally. When the temperature rise of metal surfaces by IPIB irradiation exceeds their boiling point, it is found that machining roughness on surfaces is removed. The experiments were performed with the pulsed power generator HARIMA-II at Himeji Institute of Technology. The main components of the ion beam were carbon and fluorine ions. The IPIB was irradiated to metal plates (Al, Cu and Ti) which were placed at the focal point. Machining roughness on Ti surface was removed after IPIB irradiation, while roughness on Al and Cu plates was not removed. Using the present experimental parameters (beam power density: 32 W/cm 2 , pulse width: 25 ns), the temperature rise of the Ti surface was estimated to be 8,100 K which exceed its boiling point (3,000 K). However, the estimated temperatures of Al and Cu surfaces was 2,500 and 1,500 K, respectively, that are less than their boiling points. These studies above suggests that temperature rise over the boiling point of metals is necessary for removing machining roughness on metal surfaces

Study on the effect of thermal property of metals in ultrasonic-assisted laser machining

International Nuclear Information System (INIS)

Lee, Hu Seung; Kim, Gun Woo; Park, Jong Eun; Cho, Sung Hak; Yang, Min Yang; Park, Jong Kweon

2015-01-01

The laser machining process has been proposed as an advanced process for the selective fabrication of electrodes without a mask. In this study, we adapt laser machining to metals that have different thermal properties. Based on the results, the metals exhibit a different surface morphology, heat-affected zone (HAZ), and a recast layer around the machined surface according to their thermal conductivity, boiling point, and thermal diffusivity. Then, we apply ultrasonic-assisted laser machining to remove the recast layer. The ultrasonic-assisted laser machining exhibits a better surface quality in metals with higher diffusivity than those having lower diffusivity

Investigating the effect of curved shape of bridge abutment provided with collar on local scour, experimentally and numerically

Directory of Open Access Journals (Sweden)

Y. Abdallah Mohamed

2015-06-01

Full Text Available Scour around bridge supports such as abutments can result in structural collapse and loss of life and property, so there is a need to control and minimize the local scour depth. In this paper, numerical and experimental studies were carried out to investigate the effect of different relative radii of the bridge abutment provided with collar on local scour depth. A 3-D numerical model is developed to simulate the scour at bridge abutment using SSIIM program. This model solves 3-D Navier–Stokes equations and a bed load conservation equation. The k–ε turbulence model is used to solve the Reynolds-stress term. It was found the curvature shape of bridge abutment provided with collar could share to reduce the local scour depth by more 95%. In addition, the results of simulation models agree well with the experimental data.

A Mixed Message: The School Vending Machine.

Science.gov (United States)

Hinkle, Margaret Murray

1982-01-01

Dental disease, especially tooth decay, is reaching epidemic proportions among children of school age. Since sugar is a major cause of tooth decay and since many confections are sold in schools, it is recommended that schools remove confections and other nonnutritional food items from vending machines, fund-raising activities, and food services.…

Clinical evaluation of the stability of implants placed at different supracrestal levels

OpenAIRE

Gultekin, B. Alper; Sirali, Ali; Gultekin, Pinar; Ersanli, Selim

2016-01-01

Purpose: The aim of this study was to evaluate the stability during healing and before loading of implants placed at two different supracrestal levels according to their collar texture. Materials and Methods: This retrospective study included patients who received posterior implants with the same macro design. Implants with a machined collar were placed 0.3 mm above the crestal bone (M group), while those with a laser-microtextured collar were placed 1 mm above the crestal bone (L group). ...

Quantitative assessment of the enamel machinability in tooth preparation with dental diamond burs.

Science.gov (United States)

Song, Xiao-Fei; Jin, Chen-Xin; Yin, Ling

2015-01-01

Enamel cutting using dental handpieces is a critical process in tooth preparation for dental restorations and treatment but the machinability of enamel is poorly understood. This paper reports on the first quantitative assessment of the enamel machinability using computer-assisted numerical control, high-speed data acquisition, and force sensing systems. The enamel machinability in terms of cutting forces, force ratio, cutting torque, cutting speed and specific cutting energy were characterized in relation to enamel surface orientation, specific material removal rate and diamond bur grit size. The results show that enamel surface orientation, specific material removal rate and diamond bur grit size critically affected the enamel cutting capability. Cutting buccal/lingual surfaces resulted in significantly higher tangential and normal forces, torques and specific energy (pmachinability for clinical dental practice. Copyright © 2014 Elsevier Ltd. All rights reserved.

Grinding, Machining Morphological Studies on C/SiC Composites

Science.gov (United States)

Xiao, Chun-fang; Han, Bing

2018-05-01

C/SiC composite is a typical material difficult to machine. It is hard and brittle. In machining, the cutting force is large, the material removal rate is low, the edge is prone to collapse, and the tool wear is serious. In this paper, the grinding of C/Si composites material along the direction of fiber distribution is studied respectively. The surface microstructure and mechanical properties of C/SiC composites processed by ultrasonic machining were evaluated. The change of surface quality with the change of processing parameters has also been studied. By comparing the performances of conventional grinding and ultrasonic grinding, the surface roughness and functional characteristics of the material can be improved by optimizing the processing parameters.

The impact of long working hours on psychosocial stress response among white-collar workers

OpenAIRE

LEE, Kyungjin; SUH, Chunhui; KIM, Jong-Eun; PARK, Jae Oh

2016-01-01

This study examined the association between long working hours and psychosocial stress responses. In total, 1,122 white-collar workers from a company in Korea completed self-administered questionnaires following a lecture about the study aim, procedures, and confidentiality. Psychosocial stress responses were evaluated using the Psychosocial Well-being Index - Short Form (PWI-SF), and psychosocial working conditions were evaluated with the Korean Occupational Stress Scale - Short Form (KOSS-S...

Pressure ulcers, indentation marks and pain from cervical spine immobilization with extrication collars and headblocks : An observational study

NARCIS (Netherlands)

Ham, Wietske H W; Schoonhoven, Lisette; Schuurmans, Marieke J; Leenen, Luke P H

OBJECTIVES: To describe the occurrence and severity of pressure ulcers, indentation marks and pain from the extrication collar combined with headblocks. Furthermore, the influence of time, injury severity and patient characteristics on the development of pressure ulcers, indentation marks and pain

Pressure ulcers, indentation marks and pain from cervical spine immobilization with extrication collars and headblocks: An observational study

NARCIS (Netherlands)

Ham, W.H.; Schoonhoven, L.; Schuurmans, M.J.; Leenen, L.P.

2016-01-01

OBJECTIVES: To describe the occurrence and severity of pressure ulcers, indentation marks and pain from the extrication collar combined with headblocks. Furthermore, the influence of time, injury severity and patient characteristics on the development of pressure ulcers, indentation marks and pain

Expansion of an exotic species and concomitant disease outbreaks: pigeon paramyxovirus in free-ranging Eurasian collared doves.

Science.gov (United States)

Schuler, Krysten L; Green, David E; Justice-Allen, Anne E; Jaffe, Rosemary; Cunningham, Mark; Thomas, Nancy J; Spalding, Marilyn G; Ip, Hon S

2012-06-01

Eurasian collared doves (Streptopelia decaocto) have expanded their range across the United States since their introduction several decades ago. Recent mortality events in Eurasian collared doves in Arizona and Montana, USA, during the winter of 2009-2010 were the result of pigeon paramyxovirus (PPMV), a novel disease agent. The first instance of mortality by this emerging infectious disease in this species occurred in Florida in 2001 with subsequent disease events in 2006 and 2008. Full diagnostic necropsies were performed on carcasses from the three states. PPMV was identified by RT-PCR and virus isolation and was sequenced to the VIb genotype of avian paramyxovirus-1 (APMV). Other APMVs are common in a variety of free-ranging birds, but concern is warranted because of the potential for commingling of this species with native birds, virus evolution, and threats to domestic poultry. Improved surveillance for wildlife mortality events and efforts to prevent introduction of non-native animals could reduce the threat of introducing new pathogens.

Stroke dynamics and frequency of 3 phacoemulsification machines.

Science.gov (United States)

Tognetto, Daniele; Cecchini, Paolo; Leon, Pia; Di Nicola, Marta; Ravalico, Giuseppe

2012-02-01

To measure the working frequency and the stroke dynamics of the phaco tip of 3 phacoemulsification machines. University Eye Clinic of Trieste, Italy. Experimental study. A video wet fixture was assembled to measure the working frequency using a micro camera and a micropulsed strobe-light system. A different video wet fixture was created to measure tip displacement as vectorial movement at different phaco powers using a microscopic video apparatus. The working frequency of the Infiniti Ozil machine was 43.0 kHz in longitudinal mode and 31.6 kHz in torsional mode. The frequency of the Whitestar Signature machine was 29.0 kHz in longitudinal mode and 38.0 kHz with the Ellips FX handpiece. The Stellaris machine had a frequency of 28.8 kHz. The longitudinal stroke of the 3 machines at different phaco powers was statistically significantly different. The Stellaris machine had the highest stroke extent (139 μm). The lateral movement of the Infiniti Ozil and Whitestar Signature machines differed significantly. No movement on the y-axis was observed for the Infiniti Ozil machine in torsional mode. The elliptical path of the Ellips FX handpiece had different x and y components at different phaco powers. The 3 phaco machines performed differently in terms of working frequency and stroke dynamics. The knowledge of the peculiar lateral and elliptical path strokes of Infiniti and Whitestar Signature machines may allow the surgeon to fully use these features for lens removal. Copyright © 2012 ASCRS and ESCRS. Published by Elsevier Inc. All rights reserved.

Machining of scintillator tiles for the SDC calorimeter

International Nuclear Information System (INIS)

Bertoldi, M.; Bartosz, E.; Davis, C.; Hagopian, V.; Hernandez, E.; Hu, K.; Immer, C.; Thomaston, J.

1992-01-01

This research and development on the grooving methods for the scintillating tiles of the SDC calorimeter was done to maximize the light output of scintillator plates and improve the uniformity among tiles through machining procedures. Grooves for wavelength shifting fibers in SCSN-81 can be machined from 10,000 to 60,000 RPM with a feed rate of more than 30cm/min if the plate is kept cool and the chips are removed quickly by blowing dry, cold, clean air over the cutting tool. BC499-27, a polystyrene-based scintillator, is softer and more difficult to machine. It allows a maximum rotation speed of 20,000 RPM and a maximum feed rate of 15 cm/min. A new half-keyhole shape was used for grooves, allowing safer, faster top-loading of the fibers. Three hundred tiles were machined, achieving a standard deviation of the light output of less than 7%. (Author)

Blue-collar workplaces: a setting for reducing heart health inequalities in New Zealand?

Science.gov (United States)

Novak, Brad; Bullen, Chris; Howden-Chapman, Philippa; Thornley, Simon

2007-09-07

To review the evidence for the effectiveness of workplaces as settings for cardiovascular health promotion and reduction of heart health inequalities in New Zealand. Literature review and structured appraisal of 154 articles meeting inclusion criteria, of which one review and three trials addressed cardiovascular interventions specifically, and four systematic reviews addressed the effectiveness of workplace health promotion programmes generally. The reviewed studies showed that workplaces have good potential as settings for health promotion. We found mixed but largely supportive evidence that workplace interventions can lead to improvements in health outcomes, workplace environments, lifestyles, and productivity. Workplace programmes that ranked highest in both clinical and cost-effectiveness targeted industries employing large numbers of blue-collar workers, tackled multiple risk factors, intervened at both individual and environmental levels and incorporated occupational safety components. Such programmes appear to offer a substantial return on investment for employers in other countries, but local evidence is lacking. Employers and workers in blue-collar industries should be encouraged to participate in comprehensive heart health promotion programmes as a strategy for reducing existing socioeconomic and ethnic disparities in health. However, high-quality evidence of improved employee health and productivity is needed from well-designed New Zealand-based research to ensure that these programmes are optimally configured for effectiveness and attractive to employers and employees alike.

Micro Electro Discharge Machining for Nonconductive Ceramic Materials

Directory of Open Access Journals (Sweden)

Mohammad Yeakub Ali

2018-03-01

Full Text Available In micro-electro discharge machining (micro-EDM of nonconductive ceramics, material is removed mainly by spalling due to the dominance of alternating thermal load. The established micro-EDM models established for single spark erosion are not applicable for nonconductive ceramics because of random spalling. Moreover, it is difficult to create single spark on a nonconductive ceramic workpiece when the spark is initiated by the assisting electrode. In this paper, theoretical model of material removal rate (MRR as the function of capacitance and voltage is developed for micro-EDM of nonconductive zirconium oxide (ZrO2. It is shown that the charging and discharging duration depend on the capacitance and resistances of the circuit. The number of sparks per unit time is estimated from the single spark duration s derived from heat transfer fundamentals. The model showed that both the capacitance and voltage are significant process parameters where any increase of capacitance and voltage increases the MRR. However, capacitance was found to be the dominating parameter over voltage. As in case of higher capacitances, the creation of a conductive carbonic layer on the machined surface was not stable; the effective window of machining 101 - 103 pF capacitance and 80 - 100 V gap voltage or 10 - 470 pF capacitance and 80 - 110 V gap voltage. This fact was confirmed EDX analysis where the presence of high carbon content was evident. Conversely, the spark was found to be inconsistent using parameters beyond these ranges and consequently insignificant MRR. Nevertheless, the effective number of sparks per second were close to the predicted numbers when machining conductive copper material. In addition, higher percentage of ineffective pulses was observed during the machining which eventually reduced the MRR. In case of validation, average deviations between the predicted and experimental values were found to be around 10%. Finally, micro-channels were machined on

454 sequencing reveals extreme complexity of the class II Major Histocompatibility Complex in the collared flycatcher

Directory of Open Access Journals (Sweden)

Gustafsson Lars

2010-12-01

Full Text Available Abstract Background Because of their functional significance, the Major Histocompatibility Complex (MHC class I and II genes have been the subject of continuous interest in the fields of ecology, evolution and conservation. In some vertebrate groups MHC consists of multiple loci with similar alleles; therefore, the multiple loci must be genotyped simultaneously. In such complex systems, understanding of the evolutionary patterns and their causes has been limited due to challenges posed by genotyping. Results Here we used 454 amplicon sequencing to characterize MHC class IIB exon 2 variation in the collared flycatcher, an important organism in evolutionary and immuno-ecological studies. On the basis of over 152,000 sequencing reads we identified 194 putative alleles in 237 individuals. We found an extreme complexity of the MHC class IIB in the collared flycatchers, with our estimates pointing to the presence of at least nine expressed loci and a large, though difficult to estimate precisely, number of pseudogene loci. Many similar alleles occurred in the pseudogenes indicating either a series of recent duplications or extensive concerted evolution. The expressed alleles showed unambiguous signals of historical selection and the occurrence of apparent interlocus exchange of alleles. Placing the collared flycatcher's MHC sequences in the context of passerine diversity revealed transspecific MHC class II evolution within the Muscicapidae family. Conclusions 454 amplicon sequencing is an effective tool for advancing our understanding of the MHC class II structure and evolutionary patterns in Passeriformes. We found a highly dynamic pattern of evolution of MHC class IIB genes with strong signals of selection and pronounced sequence divergence in expressed genes, in contrast to the apparent sequence homogenization in pseudogenes. We show that next generation sequencing offers a universal, affordable method for the characterization and, in perspective

Evaluating methods for estimating home ranges using GPS collars: A comparison using proboscis monkeys (Nasalis larvatus).

Science.gov (United States)

Stark, Danica J; Vaughan, Ian P; Ramirez Saldivar, Diana A; Nathan, Senthilvel K S S; Goossens, Benoit

2017-01-01

The development of GPS tags for tracking wildlife has revolutionised the study of home ranges, habitat use and behaviour. Concomitantly, there have been rapid developments in methods for estimating habitat use from GPS data. In combination, these changes can cause challenges in choosing the best methods for estimating home ranges. In primatology, this issue has received little attention, as there have been few GPS collar-based studies to date. However, as advancing technology is making collaring studies more feasible, there is a need for the analysis to advance alongside the technology. Here, using a high quality GPS collaring data set from 10 proboscis monkeys (Nasalis larvatus), we aimed to: 1) compare home range estimates from the most commonly used method in primatology, the grid-cell method, with three recent methods designed for large and/or temporally correlated GPS data sets; 2) evaluate how well these methods identify known physical barriers (e.g. rivers); and 3) test the robustness of the different methods to data containing either less frequent or random losses of GPS fixes. Biased random bridges had the best overall performance, combining a high level of agreement between the raw data and estimated utilisation distribution with a relatively low sensitivity to reduced fixed frequency or loss of data. It estimated the home range of proboscis monkeys to be 24-165 ha (mean 80.89 ha). The grid-cell method and approaches based on local convex hulls had some advantages including simplicity and excellent barrier identification, respectively, but lower overall performance. With the most suitable model, or combination of models, it is possible to understand more fully the patterns, causes, and potential consequences that disturbances could have on an animal, and accordingly be used to assist in the management and restoration of degraded landscapes.

Evaluating methods for estimating home ranges using GPS collars: A comparison using proboscis monkeys (Nasalis larvatus.

Directory of Open Access Journals (Sweden)

Danica J Stark

Full Text Available The development of GPS tags for tracking wildlife has revolutionised the study of home ranges, habitat use and behaviour. Concomitantly, there have been rapid developments in methods for estimating habitat use from GPS data. In combination, these changes can cause challenges in choosing the best methods for estimating home ranges. In primatology, this issue has received little attention, as there have been few GPS collar-based studies to date. However, as advancing technology is making collaring studies more feasible, there is a need for the analysis to advance alongside the technology. Here, using a high quality GPS collaring data set from 10 proboscis monkeys (Nasalis larvatus, we aimed to: 1 compare home range estimates from the most commonly used method in primatology, the grid-cell method, with three recent methods designed for large and/or temporally correlated GPS data sets; 2 evaluate how well these methods identify known physical barriers (e.g. rivers; and 3 test the robustness of the different methods to data containing either less frequent or random losses of GPS fixes. Biased random bridges had the best overall performance, combining a high level of agreement between the raw data and estimated utilisation distribution with a relatively low sensitivity to reduced fixed frequency or loss of data. It estimated the home range of proboscis monkeys to be 24-165 ha (mean 80.89 ha. The grid-cell method and approaches based on local convex hulls had some advantages including simplicity and excellent barrier identification, respectively, but lower overall performance. With the most suitable model, or combination of models, it is possible to understand more fully the patterns, causes, and potential consequences that disturbances could have on an animal, and accordingly be used to assist in the management and restoration of degraded landscapes.

Recovery studies for plutonium machining oil coolant

International Nuclear Information System (INIS)

Navratil, J.D.; Baldwin, C.E.

1977-01-01

Lathe coolant oil, contaminated with plutonium and having a carbon tetrachloride diluent, is generated in plutonium machining areas at Rocky Flats. A research program was initiated to determine the nature of plutonium in this mixture of oil and carbon tetrachloride. Appropriate methods then could be developed to remove the plutonium and to recycle the oil and carbon tetrachloride. Studies showed that the mixtures of spent oil and carbon tetrachloride contained particulate plutonium and plutonium species that are soluble in water or in oil and carbon tetrachloride. The particulate plutonium was removed by filtration; the nonfilterable plutonium was removed by adsorption on various materials. Laboratory-scale tests indicated the lathe-coolant oil mixture could be separated by distilling the carbon tetrachloride to yield recyclable products

Prolonged fatigue is associated with sickness absence in men but not in women: prospective study with 1-year follow-up of white-collar employees.

Science.gov (United States)

Roelen, Corné A M; van Rhenen, Willem; Groothoff, Johan W; van der Klink, Jac J L; Bültmann, Ute

2014-04-01

Prolonged fatigue adversely affects an individual's performance and functioning. The present study investigated the prospective associations between prolonged fatigue and sickness absence (SA) during 1-year follow-up. At baseline, a convenience sample of white-collar employees received the 20-item Checklist Individual Strength (CIS), which measures prolonged fatigue by covering the dimensions fatigue severity, reduced concentration, reduced motivation, and reduced physical activity. SA episodes were registered during the 1-year follow-up distinguishing between short-term (1-7 days) and long-term ( 7 days) SA episodes. Baseline CIS scores were linked to SA during follow-up by negative binomial regression models in which age, gender, job grade, and prior SA were controlled for. Six hundred and thirty-three (56 %) employees participated in the study of which 598 had complete data and were eligible for analysis. Gender was a significant effect modifier of the relationship between prolonged fatigue and SA. Therefore, the results were stratified for men (N = 365) and women (N = 233). In white-collar men, fatigue severity and reduced concentration were positively associated with the number of long-term SA episodes, while other fatigue dimensions were not significantly related to SA. In white-collar women, prolonged fatigue was not associated with SA during 1-year follow-up. The results of this study warrant more attention for prolonged fatigue in occupational healthcare practice and research. Early identification of and treatment for prolonged fatigue might prevent future health problems and SA, especially in white-collar men.

Root deformation reduces tolerance of lodgepole pine to attack by Warren root collar weevil.

Science.gov (United States)

Robert, Jeanne A; Lindgren, B Staffan

2010-04-01

Surveys were conducted on regenerating stands of lodgepole pine to determine the relationship between root deformation and susceptibility to attack by the Warren root collar weevil, Hylobius warreni Wood. The total number of trees attacked by H. warreni did not differ between planted and natural trees. A matched case-control logistic regression suggested that root cross-sectional area was more important in predicting weevil attack for naturally regenerated trees than for planted trees, but weevils were associated with a larger reduction in height-to-diameter ratios for trees with planted root characteristics than for trees with natural root form. Neither the stability of attacked versus unattacked trees differed significantly and there was no significant interaction of weevil attack and tree type, but weevil-killed trees had different root characteristics than alive, attacked trees. Lateral distribution and root cross-sectional area were significant predictors of alive attacked trees versus weevil-killed trees, suggesting that trees with poor lateral spread or poor root cross-sectional area are more likely to die from weevil attack. We conclude that root deformation does not necessarily increase susceptibility to attack but may increase the likelihood of mortality. Thus, measures to facilitate good root form are needed when planting pine in areas with high risk of Warren root collar weevil attack.

[Pressure sores secondary to immobilization with cervical collar: a complication of acute cervical injury].

Science.gov (United States)

Molano Alvarez, Esteban; Murillo Pérez, María del Ara; Salobral Villegas, María Teresa; Domínguez Caballero, Mireia; Cuenca Solanas, Manuela; García Fuentes, Carlos

2004-01-01

Cervical collars are essential in the treatment of patients with suspicion or verification of acute cervical spine injury (ACSI). One of the complications of these devices is the development of pressure scores (PS). This study aims to determine its incidence in our unit, the characteristics of patients with ACSI who suffer PS due to the collar and to describe aspects related with these injuries. We include 92 patients with ACSI hospitalized more than 24 hours from January 2002 to December 2003. We analyze demographic variables, incidence, risk factors and characteristics of the PS that develop. The incidence of these lesions was 23.9%. Patients with PS presented: a higher injury severity score (ISS) (37.5 9.8 vs. 31.3 14.9), a greater percentage of catheter carriers of intracraneal pressure (ICP) (55.6% vs. 16.2%), longer time of mechanical ventilation (15.4 8.2 vs. 6.1 9) and longer stays (24.6 10.9 vs. 10 10.3), all statistically significant (pACSI, elevated ISS, monitoring of ICP, mechanical ventilation and prolonged stays is required. The occipital zone requires special attention due to the seriousness of the injuries recorded. We suggest a specific multidisciplinary protocol for this problem.

The impact of long working hours on psychosocial stress response among white-collar workers.

Science.gov (United States)

Lee, Kyungjin; Suh, Chunhui; Kim, Jong-Eun; Park, Jae Oh

2017-02-07

This study examined the association between long working hours and psychosocial stress responses. In total, 1,122 white-collar workers from a company in Korea completed self-administered questionnaires following a lecture about the study aim, procedures, and confidentiality. Psychosocial stress responses were evaluated using the Psychosocial Well-being Index - Short Form (PWI-SF), and psychosocial working conditions were evaluated with the Korean Occupational Stress Scale - Short Form (KOSS-SF). Multivariate logistic regression analysis was performed after adjusting for demographic variables and psychosocial working conditions to examine associations between long working hours and psychosocial stress responses. In comparison with the reference group, which worked 40-44 hours per week, the crude odds ratio (OR) of the respondents who worked 60 or more hours was 4.56 (95% confidence interval (CI), 2.55-8.15) in terms of psychosocial stress responses. After adjusting for demographic variables, the adjusted OR of those working ≥60 hours was 5.61 (95% CI, 3.01-10.47). After adjusting for both demographic variables and psychosocial working conditions, the adjusted OR of those working ≥60 hours was 3.25 (95% CI, 1.56-6.79). This study found that long working hours are significantly related to psychosocial stress responses among white-collar workers in one Korean company.

IS OHS NEGLIGENCE AND EVASION AN “ERROR OF JUDGEMENT” OR “WHITE-COLLAR CRIME”? AN INTERPRETATION OF APPAREL MANUFACTURERS IN BANGLADESH

Directory of Open Access Journals (Sweden)

Muhammad Faisol Chowdhury

2016-12-01

Full Text Available This paper investigates the managerial interpretation of the terms “error of judgement” and “white-collar crime” in relation to the evasion or negligence observed in administering occupational health and safety (OHS provisions in the apparel manufacturing sector of Bangladesh. The research is qualitative in nature and follows an interpretivist paradigm. The questionnaire responses were collected from 20 mid- and top-level managers from 10 large apparel manufacturing factories located on the outskirts of Dhaka. The research reveals that all of the respondents have adequate knowledge about the relevant OHS provisions and safety protocols imposed on them by the local government and the global supply chain. They believe that the correct administration of the OHS provisions will reduce workplace accidents effectively. The research unfolds that the respondents interpret in different ways the terms "error of judgement” and “white-collar crime” in association with OHS negligence and evasion. Although empirical evidence shows that this type of negligence and evasion are considered as white-collar crime and punishable, most of the respondents in this research do not subscribe to this notion and alternatively believe that it is an “error of judgement” and therefore non-punishable.

A prospective cohort study on severe pain as a risk factor for long-term sickness absence in blue- and white-collar workers

DEFF Research Database (Denmark)

Andersen, Lars Louis; Mortensen, Ole Steen; Hansen, Jørgen Vinsløv

2011-01-01

Objective To estimate the impact of pain in different body regions on future long-term sickness absence (LTSA) among blue- and white-collar workers. Method Prospective cohort study in a representative sample of 5603 employees (the Danish Work Environment Cohort Study) interviewed in 2000, and fol......Objective To estimate the impact of pain in different body regions on future long-term sickness absence (LTSA) among blue- and white-collar workers. Method Prospective cohort study in a representative sample of 5603 employees (the Danish Work Environment Cohort Study) interviewed in 2000......, and followed in 2001-2002 in a national sickness absence register. Cox regression analysis was performed to assess the risk estimates of mutually adjusted severe pain in the neck/shoulder, low back, hand/wrist and knees for onset of LTSA, defined as receiving sickness absence compensation for at least 3...... consecutive weeks. Age, gender, body mass index, smoking and diagnosed disease were controlled for. Results In 2000 the prevalence among blue- and white-collar workers, respectively, of severe pain was 33% and 29% (neck/shoulder), 33% and 25% (low back), 16% and 11% (hand/wrists), and 16% and 12% (knees...

Convenience in white-collar crime: A resource perspective

Directory of Open Access Journals (Sweden)

Petter Gottschalk

2017-03-01

Full Text Available White-collar offenders have access to resources that make financial crime convenient. In the rare case of crime suspicion, resources are available in terms of professional attorney work, control over internal investigations, and public relations support. Hiring private investigators at an early stage of potential crime disclosure enables the organization to control the investigation mandate and influence the investigation process and the investigation output. Getting an early start on reconstruction of the past in terms of a fraud examination makes it possible for the suspect and the organization to influence what facts are relevant and how facts might be assessed in terms of possible violations of the penal code. Convenience aspects of private investigations are discussed in this article in terms of five internal investigations, two in the United States (General Motors and Lehman Brothers and three in Norway (Telenor VimpelCom, DNB Bank, and Norwegian Football Association. The aim of this research is to contribute insights into convenience associated with internal private investigations.

Changing Workplaces to Reduce Work-Family Conflict: Schedule Control in a White-Collar Organization

OpenAIRE

Kelly, Erin L.; Moen, Phyllis; Tranby, Eric

2011-01-01

Work-family conflicts are common and consequential for employees, their families, and work organizations. Can workplaces be changed to reduce work-family conflict? Previous research has not been able to assess whether workplace policies or initiatives succeed in reducing work-family conflict or increasing work-family fit. Using longitudinal data collected from 608 employees of a white-collar organization before and after a workplace initiative was implemented, we investigate whether the initi...

Interpretación en arqueología : piezas de collar de una necrópolis navarra

Directory of Open Access Journals (Sweden)

Amparo Castiela Rodríguez

2005-01-01

Full Text Available Los restos de ajuar, recuperados en la necrópolis que han seguido el rito de la cremación, nos llegan muy alterados y requieren en ocasiones un esfuerzo especial para su comprensión. En el caso de varias piezas procedentes de La Atalaya, que formaban parte de collares, cuya interpretación ofrecemos

Plasma hot machining for difficult-to-cut materials, 1

International Nuclear Information System (INIS)

Kitagawa, Takeaki; Maekawa, Katsuhiro; Kubo, Akihiko

1987-01-01

Machinability of difficult-to-cut materials has been a great concern to manufacturing engineers since demands for new materials in the aerospace and nuclear industries are more and more increasing. The purpose of this study is to develop a hot machining to improve machinability of high hardness materials. A plasma arc is used for heating materials cut. The surface just after being heated is removed as a chip by tungsten carbide tools. The turning experiments of high hardness steels with aid of plasma arc heating show not only the decrease in cutting forces but also the following effectiveness: (1) The application of the plasma hot machining to the condition, under which a built-up edge (BUE) appears in turning 0.46%C steel, makes the BUE disappeared, bringing less flank wear. (2) In the case of 18%Mn steel cutting, deep groove wear on the end-cutting edge diminishes, and roughness of the machined surface is improved by the prevention from chatter. (3) Although the chilled cast iron has high hardness of above HB = 350, the plasma hot machining makes it possible to cut it with tungsten carbide tools having less chipping and flank wear. (author)

Parameter optimization of electrochemical machining process using black hole algorithm

Science.gov (United States)

Singh, Dinesh; Shukla, Rajkamal

2017-12-01

Advanced machining processes are significant as higher accuracy in machined component is required in the manufacturing industries. Parameter optimization of machining processes gives optimum control to achieve the desired goals. In this paper, electrochemical machining (ECM) process is considered to evaluate the performance of the considered process using black hole algorithm (BHA). BHA considers the fundamental idea of a black hole theory and it has less operating parameters to tune. The two performance parameters, material removal rate (MRR) and overcut (OC) are considered separately to get optimum machining parameter settings using BHA. The variations of process parameters with respect to the performance parameters are reported for better and effective understanding of the considered process using single objective at a time. The results obtained using BHA are found better while compared with results of other metaheuristic algorithms, such as, genetic algorithm (GA), artificial bee colony (ABC) and bio-geography based optimization (BBO) attempted by previous researchers.

The Effects of Different Electrode Types for Obtaining Surface Machining Shape on Shape Memory Alloy Using Electrochemical Machining

Science.gov (United States)

Choi, S. G.; Kim, S. H.; Choi, W. K.; Moon, G. C.; Lee, E. S.

2017-06-01

Shape memory alloy (SMA) is important material used for the medicine and aerospace industry due to its characteristics called the shape memory effect, which involves the recovery of deformed alloy to its original state through the application of temperature or stress. Consumers in modern society demand stability in parts. Electrochemical machining is one of the methods for obtained these stabilities in parts requirements. These parts of shape memory alloy require fine patterns in some applications. In order to machine a fine pattern, the electrochemical machining method is suitable. For precision electrochemical machining using different shape electrodes, the current density should be controlled precisely. And electrode shape is required for precise electrochemical machining. It is possible to obtain precise square holes on the SMA if the insulation layer controlled the unnecessary current between electrode and workpiece. If it is adjusting the unnecessary current to obtain the desired shape, it will be a great contribution to the medical industry and the aerospace industry. It is possible to process a desired shape to the shape memory alloy by micro controlling the unnecessary current. In case of the square electrode without insulation layer, it derives inexact square holes due to the unnecessary current. The results using the insulated electrode in only side show precise square holes. The removal rate improved in case of insulated electrode than others because insulation layer concentrate the applied current to the machining zone.

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

Directory of Open Access Journals (Sweden)

Ruisong JIANG

2018-01-01

Full Text Available In situ formed TiB2 particle reinforced aluminum matrix composites (TiB2/Al MMCs have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB2 particles, the machinability is still a problem which restricts the application of TiB2/Al MMCs. In order to meet the industrial requirements, the influence of TiB2 particles on the machinability of TiB2/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1 the machining force of TiB2/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2 the residual stress of TiB2/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3 the surface roughness of TiB2/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4 a multi-objective optimization model for surface roughness and material removal rate (MRR was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.

Achieving precision in high density batch mode micro-electro-discharge machining

International Nuclear Information System (INIS)

Richardson, Mark T; Gianchandani, Yogesh B

2008-01-01

This paper reports a parametric study of batch mode micro-electro-discharge machining (µEDM) of high density features in stainless steel. Lithographically fabricated copper tools with single cross, parallel line and 8 × 8 circle/square array features of 5–100 µm width and 5–75 µm spacing were used to quantify trends in machining tolerance and the impact of debris accumulation. As the tool feature density is increased, debris accumulation effects begin to dominate, eventually degrading both tool and workpiece. Two independent techniques for mitigating this debris buildup are separately investigated. The first is a passivation coating which suppresses spurious discharges triggered from the sidewalls of the machining tool. By this method, the mean tool wear rate decreases from a typical of about 34% to 1.7% and machining non-uniformity reduces from 4.9 µm to 1.1 µm across the workpiece. The second technique involves a two-step machining process that enhances the hydrodynamic removal of machining debris compared to standard methods. This improves surface and edge finish, machining time and tool wear

Analysis of microplastics and their removal from water

OpenAIRE

Oladejo, Abiola

2017-01-01

Removal of microplastics from water was studied using extraction with oil. The aim of the thesis was to remove microplastics from water using an organic medium, and to analyse the amount of microplastics in the media involved. The separation of different microplastic types was done by conducting experiments in the laboratory. The microplastics were made by grinding and sieving plastics with a grinding machine before adding them to water and oil, which serves as the organic medium. Tw...

Non-machinery dialysis that achieves blood purification therapy without using full-scale dialysis machines.

Science.gov (United States)

Abe, Takaya; Onoda, Mistutaka; Matsuura, Tomohiko; Sugimura, Jun; Obara, Wataru; Sato, Toshiya; Takahashi, Mihoko; Chiba, Kenta; Abe, Tomiya

2017-09-01

An electrical or water supply and a blood purification machine are required for renal replacement therapy. There is a possibility that acute kidney injury can occur in large numbers and on a wide scale in the case of a massive earthquake, and there is the potential risk that the current supply will be unable to cope with acute kidney injury cases. However, non-machinery dialysis requires exclusive circuits and has the characteristic of not requiring the full-scale dialysis machines. We performed perfusion experiments that used non-machinery dialysis and recent blood purification machines in 30-min intervals, and the effectiveness of non-machinery dialysis was evaluated by the assessing the removal efficiency of potassium, which causes lethal arrhythmia during acute kidney injury. The non-machinery dialysis potassium removal rate was at the same level as continuous blood purification machines with a dialysate flow rate of 5 L/h after 15 min and continuous blood purification machines with a dialysate flow rate of 3 L/h after 30 min. Non-machinery dialysis required an exclusive dialysate circuit, the frequent need to replace bags, and new dialysate exchanged once every 30 min. However, it can be seen as an effective renal replacement therapy for crush-related acute kidney injury patients, even in locations or facilities not having the full-scale dialysis machines.

Machinability of Al 6061 Deposited with Cold Spray Additive Manufacturing

Science.gov (United States)

Aldwell, Barry; Kelly, Elaine; Wall, Ronan; Amaldi, Andrea; O'Donnell, Garret E.; Lupoi, Rocco

2017-10-01

Additive manufacturing techniques such as cold spray are translating from research laboratories into more mainstream high-end production systems. Similar to many additive processes, finishing still depends on removal processes. This research presents the results from investigations into aspects of the machinability of aluminum 6061 tubes manufactured with cold spray. Through the analysis of cutting forces and observations on chip formation and surface morphology, the effect of cutting speed, feed rate, and heat treatment was quantified, for both cold-sprayed and bulk aluminum 6061. High-speed video of chip formation shows changes in chip form for varying material and heat treatment, which is supported by the force data and quantitative imaging of the machined surface. The results shown in this paper demonstrate that parameters involved in cold spray directly impact on machinability and therefore have implications for machining parameters and strategy.

In-plant test and evaluation of the neutron collar for verification of PWR fuel assemblies at Resende, Brazil

International Nuclear Information System (INIS)

Menlove, H.O.; Marzo, M.A.S.; de Almeida, S.G.; de Almeida, M.C.; Moitta, L.P.M.; Conti, L.F.; de Paiva, J.R.T.

1985-11-01

The neutron-coincidence collar has been evaluated for the measurement of pressurized-water reactor (PWR) fuel assemblies at the Fabrica de Elementos Combustiveis plant in Resende, Brazil. This evaluation was part of the cooperative-bilateral-safeguards technical-exchange program between the United States and Brazil. The neutron collar measures the 235 U content per unit length of full fuel assemblies using neutron interrogation and coincidence counting. The 238 U content is measured in the passive mode without the AmLi neutron-interrogation source. The extended evaluation took place over a period of 6 months with both scanning and single-zone measurements. The results of the tests gave a coincidence-response standard deviation of 0.7% (sigma = 1.49% for mass) for the active case and 2.5% for the passive case in 1000-s measurement times. The length measurement in the scanning mode was accurate to 0.77%. The accuracies of different calibration methods were evaluated and compared

Practical aspects of the use of three-phase alternating current electric machines in electricity storage system

Science.gov (United States)

Ciucur, Violeta

2015-02-01

Of three-phase alternating current electric machines, it brings into question which of them is more advantageous to be used in electrical energy storage system by pumping water. The two major categories among which are given dispute are synchronous and the asynchronous machine. To consider the synchronous machine with permanent magnet configuration because it brings advantages compared with conventional synchronous machine, first by removing the necessary additional excitation winding. From the point of view of loss of the two types of machines, the optimal adjustment of the magnetic flux density is obtained to minimize the copper loss by hysteresis and eddy currents.

Hydraulic stud-tensioning machines in reactor technology

International Nuclear Information System (INIS)

Lachner, H.

1978-01-01

Hydraulic multiple stud tensioner (MST) for the simultaneous prestressing of all the stud bolts is make it possible to achieve highly accurate prestress levels in the highly stressed bolts holding down the top head of reactor pressure vessels. These machines can remove and replace the nuts and studs, and can rotate these components upwards and downwards, during the operation of opening and closing the reactor pressure vessel. In order to reduce the radiation exposure of the service personnel, and also to reduce the time required for this work which may lie in the critical path of the refuelling time schedule, it is desirable to achieve complete mechanisation of these machines, including remote control and remote monitoring. The devices and components required for this purpose are without precedent in machine construction with respect to their functions and to the load range involved. The reported operating experience therefore also covers some points of general interest while the data on maintenance reflect the known status of the technology. (orig.) [de

A Cultural Reading of a Chinese White-Collar Workplace Bestseller and its Filmic Adaptation: Li Ke’s A Story of Lala’s Promotion and Go Lala Go!

Directory of Open Access Journals (Sweden)

Shenshen Cai

2014-08-01

Full Text Available In 2007, Li Ke’s novel A Story of Lala’s Promotion (Du Lala Shengzhi Ji became a bestseller among Chinese white-collar workers in foreign-owned (Western companies and struck a chord with the Chinese middle class. The novel revolves around office politics, Western company culture and the white-collar lifestyle, the ‘shelved ladies’ phenomenon and middle-class aesthetics. To decipher the embedded cultural codes of this book, this study undertakes a textual analysis of the plots of A Story of Lala’s Promotion and its filmic adaptation, Go Lala Go! (Du Lala Shengzhi Ji dir. Xu Jinglei, 2010. This paper conducts a trans-media adaption study (from fiction to film to examine three interrelated themes in the novel and the film. First, focusing on the influence of Western corporate culture on Chinese white-collar workers under economic globalisation, the widely circulating rules of Western workplaces are interpreted, clarifying the acculturating process of Western culture over its Chinese counterpart. The paper further explains that on the platform provided by foreign companies, and with the influence and training of Western corporate culture, intelligent and diligent young Chinese aspirational women struggle and realise their dreams in the workplace. Second, employing a feminist perspective, an attempt is made to address the situation of contemporary Chinese white-collar women represented by the contemporary social phenomenon of the ‘shelved ladies’, which also serves as an emblem of female independence and individualism. Third, through an analysis of the filmic adaptation, which focuses on the white-collar female’s lifestyle and consumption habits, the paper also highlights the contemporary Chinese population’s pursuit of a middle-class identity and aesthetic that mirrors the overwhelming consumerism of post-socialist China.

Study on the Gap Flow Simulation in EDM Small Hole Machining with Ti Alloy

Directory of Open Access Journals (Sweden)

Shengfang Zhang

2017-01-01

Full Text Available In electrical discharge machining (EDM process, the debris removed from electrode material strongly affects the machining efficiency and accuracy, especially for the deep small hole machining process. In case of Ti alloy, the debris movement and removal process in gap flow between electrodes for small hole EDM process is studied in this paper. Based on the solid-liquid two-phase flow equation, the mathematical model on the gap flow field with flushing and self-adaptive disturbation is developed. In our 3D simulation process, the count of debris increases with number of EDM discharge cycles, and the disturbation generated by the movement of self-adaptive tool in the gap flow is considered. The methods of smoothing and remeshing are also applied in the modeling process to enable a movable tool. Under different depth, flushing velocity, and tool diameter, the distribution of velocity field, pressure field of gap flow, and debris movement are analyzed. The statistical study of debris distribution under different machining conditions is also carried out. Finally, a series of experiments are conducted on a self-made machine to verify the 3D simulation model. The experiment results show the burn mark at hole bottom and the tapered wall, which corresponds well with the simulating conclusion.

Analysis of machining and machine tools

CERN Document Server

Liang, Steven Y

2016-01-01

This book delivers the fundamental science and mechanics of machining and machine tools by presenting systematic and quantitative knowledge in the form of process mechanics and physics. It gives readers a solid command of machining science and engineering, and familiarizes them with the geometry and functionality requirements of creating parts and components in today’s markets. The authors address traditional machining topics, such as: single and multiple point cutting processes grinding components accuracy and metrology shear stress in cutting cutting temperature and analysis chatter They also address non-traditional machining, such as: electrical discharge machining electrochemical machining laser and electron beam machining A chapter on biomedical machining is also included. This book is appropriate for advanced undergraduate and graduate mechani cal engineering students, manufacturing engineers, and researchers. Each chapter contains examples, exercises and their solutions, and homework problems that re...

Reducing the uncertainty in robotic machining by modal analysis

Science.gov (United States)

Alberdi, Iñigo; Pelegay, Jose Angel; Arrazola, Pedro Jose; Ørskov, Klaus Bonde

2017-10-01

The use of industrial robots for machining could lead to high cost and energy savings for the manufacturing industry. Machining robots offer several advantages respect to CNC machines such as flexibility, wide working space, adaptability and relatively low cost. However, there are some drawbacks that are preventing a widespread adoption of robotic solutions namely lower stiffness, vibration/chatter problems and lower accuracy and repeatability. Normally due to these issues conservative cutting parameters are chosen, resulting in a low material removal rate (MRR). In this article, an example of a modal analysis of a robot is presented. For that purpose the Tap-testing technology is introduced, which aims at maximizing productivity, reducing the uncertainty in the selection of cutting parameters and offering a stable process free from chatter vibrations.

Combination of ethylene glycol with sucrose increases survival rate after vitrification of somatic tissue of collared peccaries (Pecari tajacu Linnaeus, 1758

Directory of Open Access Journals (Sweden)

Alana A. Borges

Full Text Available ABSTRACT: The cryopreservation of somatic tissue in collared peccaries promotes an alternative source of genetic material of this specie. The solid-surface vitrification (SSV is a great option for tissue conservation; nevertheless, the optimization of SSV requirements is necessary, especially when referred to cryoprotectants that will compose the vitrification solution. Therefore, the aim was to evaluate the effect of the presence of 0.25 M sucrose in addition to different combinations (only or association and concentrations (1.5 M or 3.0 M of ethylene glycol (EG and/or dimethyl sulfoxide (DMSO in the somatic tissue vitrification of collared peccaries. Subsequently, we tested six combinations of cryoprotectants with or without sucrose in Dulbecco modified Eagle medium (DMEM plus 10% fetal bovine serum (FBS. Thus, 3.0 M EG with sucrose was able to maintain normal tissue characteristics compared with non-vitrified (control, especially for the volumetric ratio of epidermis (61.2 vs. 58.7% and dermis (34.5 vs. 36.6%, number of fibroblast (90.3 vs. 127.0, argyrophilic nucleolar organizer region (AgNOR ratio (0.09 vs. 0.17% and nucleus area (15.4 vs. 14.5 μm2 respectively. In conclusion, 3.0 M EG with 0.25 M sucrose and 10% FBS resulted in a better cryoprotectant composition in the SSV for somatic tissue of collared peccaries.

Total workload, work stress and perceived symptoms in Swedish male and female white-collar employees.

Science.gov (United States)

Krantz, Gunilla; Berntsson, Leeni; Lundberg, Ulf

2005-04-01

The aim of this study was to analyse how paid work, unpaid household tasks, child care, work-child care interactions and perceived work stress are associated with reported symptoms in male and female white-collar employees. A questionnaire was mailed to 1300 men and 1300 women belonging to the white-collar sector, with at least 35 hours of regular employment a week and a participant age of between 32 and 58 years. It contained items relating to total workload (hours spent on paid work, unpaid household tasks and childcare), subjective indices for work stress and symptoms. The response rate was 65% (743 women; 595 men). Gender difference in symptom prevalence was tested by analyses of variance. Odds ratios were used to estimate the bivariate associations between work-related variables and symptom prevalence. A multivariate analysis estimated the effect of paid and unpaid work interaction, work-childcare interplay and possible synergy. The frequency and severity of symptoms was higher in women than in men (P women's health was determined by the interaction between conditions at work and household duties (OR 2.09; 1.06-4.14), whereas men responded more selectively to long working hours, i.e. >50 h/week (OR 1.61; 1.02-2.54). However, childcare (women.

A Cultural Reading of a Chinese White-Collar Workplace Bestseller and its Filmic Adaptation: Li Ke’s A Story of Lala’s Promotion and Go Lala Go!

OpenAIRE

Shenshen Cai

2014-01-01

In 2007, Li Ke’s novel A Story of Lala’s Promotion (Du Lala Shengzhi Ji) became a bestseller among Chinese white-collar workers in foreign-owned (Western) companies and struck a chord with the Chinese middle class. The novel revolves around office politics, Western company culture and the white-collar lifestyle, the ‘shelved ladies’ phenomenon and middle-class aesthetics. To decipher the embedded cultural codes of this book, this study undertakes a textual analysis of the plots of A Story of ...

Use of apparent thickness for preprocessing of low-frequency electromagnetic data in inversion-based multibarrier evaluation workflow

Science.gov (United States)

Omar, Saad; Omeragic, Dzevat

2018-04-01

The concept of apparent thicknesses is introduced for the inversion-based, multicasing evaluation interpretation workflow using multifrequency and multispacing electromagnetic measurements. A thickness value is assigned to each measurement, enabling the development of two new preprocessing algorithms to remove casing collar artifacts. First, long-spacing apparent thicknesses are used to remove, from the pipe sections, artifacts ("ghosts") caused by the transmitter crossing a casing collar or corrosion. Second, a collar identification, localization, and assignment algorithm is developed to enable robust inversion in collar sections. Last, casing eccentering can also be identified on the basis of opposite deviation of short-spacing phase and magnitude apparent thicknesses from the nominal value. The proposed workflow can handle an arbitrary number of nested casings and has been validated on synthetic and field data.

Experimental investigation of the tip based micro/nano machining

Science.gov (United States)

Guo, Z.; Tian, Y.; Liu, X.; Wang, F.; Zhou, C.; Zhang, D.

2017-12-01

Based on the self-developed three dimensional micro/nano machining system, the effects of machining parameters and sample material on micro/nano machining are investigated. The micro/nano machining system is mainly composed of the probe system and micro/nano positioning stage. The former is applied to control the normal load and the latter is utilized to realize high precision motion in the xy plane. A sample examination method is firstly introduced to estimate whether the sample is placed horizontally. The machining parameters include scratching direction, speed, cycles, normal load and feed. According to the experimental results, the scratching depth is significantly affected by the normal load in all four defined scratching directions but is rarely influenced by the scratching speed. The increase of scratching cycle number can increase the scratching depth as well as smooth the groove wall. In addition, the scratching tests of silicon and copper attest that the harder material is easier to be removed. In the scratching with different feed amount, the machining results indicate that the machined depth increases as the feed reduces. Further, a cubic polynomial is used to fit the experimental results to predict the scratching depth. With the selected machining parameters of scratching direction d3/d4, scratching speed 5 μm/s and feed 0.06 μm, some more micro structures including stair, sinusoidal groove, Chinese character '田', 'TJU' and Chinese panda have been fabricated on the silicon substrate.

Shaft Boring Machine: A method of mechanized vertical shaft excavation

International Nuclear Information System (INIS)

Goodell, T.M.

1991-01-01

The Shaft Boring Machine (SBM) is a vertical application of proven rock boring technology. The machine applies a rotating cutter wheel with disk cutters for shaft excavation. The wheel is thrust against the rock by hydraulic cylinders and slews about the shaft bottom as it rotates. Cuttings are removed by a clam shell device similar to conventional shaft mucking and the muck is hoisted by buckets. The entire machine moves down (and up) the shaft through the use of a system of grippers thrust against the shaft wall. These grippers and their associated cylinders also provide the means to maintain verticality and stability of the machine. The machine applies the same principles as tunnel boring machines but in a vertical mode. Other shaft construction activities such as rock bolting, utility installation and shaft concrete lining can be accomplished concurrent with shaft boring. The method is comparable in cost to conventional sinking to a depth of about 460 meters (1500 feet) beyond which the SBM has a clear host advantage. The SBM has a greater advantage in productivity in that it can excavate significantly faster than drill and blast methods

Patterns of smoking and its association with psychosocial work conditions among blue-collar and service employees of hospitality venues in Shenyang, PR China.

Science.gov (United States)

Li, Xun; Liang, Huiying; Li, Xuelian; Guan, Peng; Yin, Zhihua; Zhou, Baosen

2010-01-27

To characterize the smoking patterns of hospitality employees in blue-collar and service occupations, and to examine its relations with psychosocial work conditions. The Shenyang Hospitality Industry Employees Survey-a face-to-face cross-sectional study of representative hospitality industry employees-was conducted between March and July 2008. A total of 4,213 workers were selected using stratified random cluster sampling designs, and final analyses were performed on 2,508 blue-collar and service subjects. Multilevel-logistic regression models were used to estimate the contribution of psychosocial work conditions to smoking status. Blue-collar and service employees smoked at a rate 1.4 times that of the general population (49.4% vs. 35.8%), more particularly for females (12.9% vs. 3.08%). Strain jobs had significantly higher odds ratio of daily smoking (OR 2.09, 95%CI: 1.28-3.41) compared to the relaxed category. The passive jobs (OR 2.01, 95%CI 1.27 to 3.17), highest job demands (OR 1.72, 95%CI: 1.13-2.61), and lowest job control (OR 2.56, 95%CI: 1.57-4.16) were also associated with a significantly higher daily smoking ratio. The negative relationship between job stability and smoking behavior was slightly stronger among daily than occasional smokers. However, neither job strain nor any of its components was found to be significantly associated with occasional smoking. Smoking in hospitality blue-collar and service employees is certainly a major occupational health problem in Shenyang. This evidence also suggests an association between psychosocial-work conditions and smoking status, and implies that more intervention studies where changes in work environment are carried out in combination with health promotion interventions should be performed.

El collar de la paloma : tratado sobre el amor y los amantes

Directory of Open Access Journals (Sweden)

Paulina López Pita

1999-01-01

Full Text Available Se recoge en este trabajo la opinión que algunos estudiosos han dado sobre una de las mejores obras de la literatura árabe, calificada por don Emilio García Gómez de auténtica joya literaria. Su autor, el ilustre polígrafo cordobés, Ibn Hazm (994-1064, comenzó a escribirla en el año 1022 en unas duras condiciones, como él mismo reconoce, cuando se hallaba cautivo en dativa. Por entonces, el califato cordobés mostraba ya sus primeros síntomas de debilidad. Esta obra esta escrita en árabe purísimo y en rica prosa en la que se intercalan versos con un profundo sentimiento. En ella su autor nos narra aspectos del amor basados en su propia experiencia, y en lo que le contaron gentes de fiar, transmitiendo, en suma, como amaron las gentes de al-Andalus durante el gobierno de la dinastía omeya; por este motivo, algunos consideran, en parte, este libro como la autobiografía de su autor y de las gentes que le rodearon. Ibn Hazm compuso esta obra por encargo de un amigo y a través de ella le ofrece, por la amistad que les une, «ayuda» para alcanzar la verdad. En los sucesivos capítulos de que consta «El collar», el autor nos habla de los fundamentos del amor, entre los que destaca, la esencia del amor, las formas de enamoramiento,etc... de los accidentes del amor y de sus cualidades loables y vituperables; de las malaventuras que sobrevienen al amor, de la fealdad del pecado y de la castidad. No obstante, a pesar del plan previo establecido por el autor, estos temas se mezclan unos con otros, y de ello se excusa Ibn Hazm. «El collar de la paloma» ha tenido una gran divulgación, siendo traducido a las principales lenguas, y en él han querido encontrar, estudiosos de la literatura medieval ciertas similitudes.This report contains some opinión from several experts about one of the masterpieces of the arab literature, considered as an authentic jewel by Emilio García Gómez. Its author, the famous cordovan polygraph Ibn Hazm (994

Process parameter optimization based on principal components analysis during machining of hardened steel

Directory of Open Access Journals (Sweden)

Suryakant B. Chandgude

2015-09-01

Full Text Available The optimum selection of process parameters has played an important role for improving the surface finish, minimizing tool wear, increasing material removal rate and reducing machining time of any machining process. In this paper, optimum parameters while machining AISI D2 hardened steel using solid carbide TiAlN coated end mill has been investigated. For optimization of process parameters along with multiple quality characteristics, principal components analysis method has been adopted in this work. The confirmation experiments have revealed that to improve performance of cutting; principal components analysis method would be a useful tool.

Long working hours and risk for hypertension in Japanese male white collar workers.

Science.gov (United States)

Nakanishi, N; Yoshida, H; Nagano, K; Kawashimo, H; Nakamura, K; Tatara, K

2001-05-01

To evaluate the association of long working hours with the risk for hypertension. A five year prospective cohort study. Work site in Osaka, Japan. 941 hypertension free Japanese male white collar workers aged 35-54 years were prospectively examined by serial annual health examinations. Men in whom borderline hypertension and hypertension were found during repeated surveys were defined as incidental cases of borderline hypertension and hypertension. 336 and 88 men developed hypertension above the borderline level and definite hypertension during the 3940 and 4531 person years, respectively. After controlling for potential predictors of hypertension, the relative risk for hypertension above the borderline level, compared with those who worked hours per day, was 0.63 (95% confidence intervals (CI): 0.43, 0.91) for those who worked 10.0-10.9 hours per day and 0.48 (95% CI: 0.31, 0.74) for those who worked > or = 11.0 hours per day. The relative risk for definite hypertension, compared with those who worked hours per day, was 0.33 (95% CI: 0.11, 0.95) for those who worked > or = 11.0 hours per day. The multivariate adjusted slopes of diastolic blood pressure (DBP) and mean arterial blood pressure (MABP) during five years of follow up decreased as working hours per day increased. From the multiple regression analyses, working hours per day remained as an independent negative factor for the slopes of systolic blood pressure, DBP, and MABP. These results indicate that long working hours are negatively associated with the risk for hypertension in Japanese male white collar workers.

Proposal for the award of two contracts for the supply of fine-blanked austenitic steel collars for the cold masses of the LHC superconducting dipole magnets

CERN Document Server

1999-01-01

This document concerns the award of two contracts for the supply of 12 500 000 fine-blanked austenitic steel collars in three different shapes and of two different types for the cold masses of the LHC superconducting dipole magnets. Following a market survey carried out among 70 firms in fourteen Member States and one firm in Japan, a call for tenders (IT-2469/LHC/LHC) was sent on 3 June 1999 to eleven firms in five Member States and one firm in Japan. By the closing date, CERN had received five tenders. The Finance Committee is invited to agree to the negotiation of two contracts with: - MALVESTITI (IT) for the supply of up to 7 812 500 fine-blanked austenitic steel collars, which represents 5/8 of the total quantity required for the cold masses of the LHC superconducting dipole magnets, for a total amount of up to 6 908 509 Swiss francs, subject to revision for contractual deliveries after 31 December 2001, with an option for the supply of up to 4 687 500 additional fine-blanked austenitic steel collars, wh...

Influence of collar design on peri-implant tissue healing around immediate implants: A pilot study in Foxhound dogs.

Science.gov (United States)

Calvo-Guirado, José Luis; López-López, Patricia Jara; Maté Sánchez de Val, José Eduardo; Mareque-Bueno, Javier; Delgado-Ruiz, Rafael Arcesio; Romanos, Georgios E

2015-07-01

The study aims to assess the soft tissue level (STL) and crestal bone level (CBL), of titanium dental implants with different mixed collar abutments configurations. This study included 48 implants with the same dimensions. They were divided into two groups of 24 implants each one: implants with a polished collar of 2 mm plus a roughened area of 0.8 mm (CONTROL) and implants with a polished collar of 0.8 mm plus a micro-threated and roughened area of 2 mm (TEST). The implants were inserted randomly in the post-extraction sockets of P2, P3, P4, and M1 bilaterally in the lower jaw of six foxhound dogs. STL and CBL were evaluated after 8 and 12 weeks by histology and histometry. All implants were clinically and histologically osseointegrated. Healing patterns examined microscopically at 8 and 12 weeks for both groups yielded similar qualitative findings for the STL evaluation, without significant differences between groups (P > 0.05). CBL was significantly higher in the buccal side in comparison with the lingual side for both groups (P implant shoulder to the top of the bony crest) and IS-C (distance from the implant shoulder to the first bone-to-implant contact) values significantly higher for control group in comparison with test (P < 0.05). At 12 weeks, CBL showed increased values for both groups that were higher in controls group in comparison with test (P < 0.05). Bony crest resorption could not be avoided both at test and control sites. However, the neck conformation at the test sites reduced the buccal bone resorption. Soft tissue dimensions were similar both at the test and control sites. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

A Data Flow Model to Solve the Data Distribution Changing Problem in Machine Learning

Directory of Open Access Journals (Sweden)

Shang Bo-Wen

2016-01-01

Full Text Available Continuous prediction is widely used in broad communities spreading from social to business and the machine learning method is an important method in this problem.When we use the machine learning method to predict a problem. We use the data in the training set to fit the model and estimate the distribution of data in the test set.But when we use machine learning to do the continuous prediction we get new data as time goes by and use the data to predict the future data, there may be a problem. As the size of the data set increasing over time, the distribution changes and there will be many garbage data in the training set.We should remove the garbage data as it reduces the accuracy of the prediction. The main contribution of this article is using the new data to detect the timeliness of historical data and remove the garbage data.We build a data flow model to describe how the data flow among the test set, training set, validation set and the garbage set and improve the accuracy of prediction. As the change of the data set, the best machine learning model will change.We design a hybrid voting algorithm to fit the data set better that uses seven machine learning models predicting the same problem and uses the validation set putting different weights on the learning models to give better model more weights. Experimental results show that, when the distribution of the data set changes over time, our time flow model can remove most of the garbage data and get a better result than the traditional method that adds all the data to the data set; our hybrid voting algorithm has a better prediction result than the average accuracy of other predict models

Robotic refueling machine

International Nuclear Information System (INIS)

Challberg, R.C.; Jones, C.R.

1996-01-01

One of the longest critical path operations performed during the outage is removing and replacing the fuel. A design is currently under development for a refueling machine which would allow faster, fully automated operation and would also allow the handling of two fuel assemblies at the same time. This design is different from current designs, (a) because of its lighter weight, making increased acceleration and speed possible, (b) because of its control system which makes locating the fuel assembly more dependable and faster, and (c) because of its dual handling system allowing simultaneous fuel movements. The new design uses two robotic arms to span a designated area of the vessel and the fuel storage area. Attached to the end of each robotic arm is a lightweight telescoping mast with a pendant attached to the end of each mast. The pendant acts as the base unit, allowing attachment of any number of end effectors depending on the servicing or inspection operation. Housed within the pendant are two television cameras used for the positioning control system. The control system is adapted from the robotics field using the technology known as machine vision, which provides both object and character recognition techniques to enable relative position control rather than absolute position control as in past designs. The pendant also contains thrusters that are used for fast, short distance, precise positioning. The new refueling machine system design is capable of a complete off load and reload of an 872 element core in about 5.3 days compared to 13 days for a conventional system

High resolution micro ultrasonic machining for trimming 3D microstructures

International Nuclear Information System (INIS)

Viswanath, Anupam; Li, Tao; Gianchandani, Yogesh

2014-01-01

This paper reports on the evaluation of a high resolution micro ultrasonic machining (HR-µUSM) process suitable for post fabrication trimming of complex 3D microstructures made from fused silica. Unlike conventional USM, the HR-µUSM process aims for low machining rates, providing high resolution and high surface quality. The machining rate is reduced by keeping the micro-tool tip at a fixed distance from the workpiece and vibrating it at a small amplitude. The surface roughness is improved by an appropriate selection of abrasive particles. Fluidic modeling is performed to study interaction among the vibrating micro-tool tip, workpiece, and the slurry. Using 304 stainless steel (SS304) tool tips of 50 µm diameter, the machining performance of the HR-µUSM process is characterized on flat fused silica substrates. The depths and surface finish of machined features are evaluated as functions of slurry concentrations, separation between the micro-tool and workpiece, and machining time. Under the selected conditions, the HR-µUSM process achieves machining rates as low as 10 nm s −1  averaged over the first minute of machining of a flat virgin sample. This corresponds to a mass removal rate of ≈20 ng min −1 . The average surface roughness, S a , achieved is as low as 30 nm. Analytical and numerical modeling are used to explain the typical profile of the machined features as well as machining rates. The process is used to demonstrate trimming of hemispherical 3D shells made of fused silica. (paper)

Gender differences in work-home interplay and symptom perception among Swedish white-collar employees.

Science.gov (United States)

Berntsson, L; Lundberg, U; Krantz, G

2006-12-01

To analyse gender differences in paid and unpaid workload and symptoms in matched groups of Swedish white-collar workers with children. Paid and unpaid workload and perceived stress from paid work, conflict between demands and control over household work were measured by a total workload (TWL) questionnaire. Some symptoms were rated with regard to frequency and severity as a measure of health. Cross-sectional analyses were performed. Matched groups of male (n = 440) and female (n = 529) well-educated white-collar workers in full-time employment, aged 32-58 years and living with children in the home. Women in higher positions in Sweden are healthier than the average population of women, but report more symptoms than men in the same position as well as more stress from paid work, more conflict between demands and a greater TWL. However, women also reported more control over household duties and TWL was not associated with more symptoms. The men were mainly focused on their paid work role and perhaps even more so than men in the general population as they were fairly resistant to feelings of conflicting demands. Even among matched groups of full-time employed, well-educated men and women, traditional gender differences in division of responsibilities and time allocation were found. Even though the women were healthy at this stage, they might risk future ill health, owing to high workload, stress and feelings of conflicting demands.

Rotary ultrasonic machining of CFRP: A comparison with grinding.

Science.gov (United States)

Ning, F D; Cong, W L; Pei, Z J; Treadwell, C

2016-03-01

Carbon fiber reinforced plastic (CFRP) composites have been intensively used in various industries due to their superior properties. In aircraft and aerospace industry, a large number of holes are required to be drilled into CFRP components at final stage for aircraft assembling. There are two major types of methods for hole making of CFRP composites in industry, twist drilling and its derived multi-points machining methods, and grinding and its related methods. The first type of methods are commonly used in hole making of CFRP composites. However, in recent years, rotary ultrasonic machining (RUM), a hybrid machining process combining ultrasonic machining and grinding, has also been successfully used in drilling of CFRP composites. It has been shown that RUM is superior to twist drilling in many aspects. However, there are no reported investigations on comparisons between RUM and grinding in drilling of CFRP. In this paper, these two drilling methods are compared in five aspects, including cutting force, torque, surface roughness, hole diameter, and material removal rate. Copyright © 2015 Elsevier B.V. All rights reserved.

Machine rates for selected forest harvesting machines

Science.gov (United States)

R.W. Brinker; J. Kinard; Robert Rummer; B. Lanford

2002-01-01

Very little new literature has been published on the subject of machine rates and machine cost analysis since 1989 when the Alabama Agricultural Experiment Station Circular 296, Machine Rates for Selected Forest Harvesting Machines, was originally published. Many machines discussed in the original publication have undergone substantial changes in various aspects, not...

Measuring the actual I-131 thyroid uptake curve with a collar detector system: a feasibility study

Energy Technology Data Exchange (ETDEWEB)

Brinks, Peter; Van Gils, Koen; Dickerscheid, Dennis B.M.; Habraken, Jan B.A. [Department of Medical Physics, St. Antonius Hospital, Nieuwegein (Netherlands); Kranenborg, Ellen; Lavalaye, Jules [Department of Nuclear Medicine, St. Antonius Hospital, Nieuwegein (Netherlands)

2017-06-15

Radionuclide therapy using I-131 is commonly used for the treatment of benign thyroid diseases. The therapeutic dose to be administered is calculated based on the type of disease, the volume of the thyroid, and the measured uptake percentage. This methodology assumes a similar biological half-life of iodine, whereas in reality a large variation in biological half-life is observed. More knowledge about the actual biological half-life of iodine for individual patients will improve the quantification of the delivered radiation dose during radioiodine therapy and could aid the evaluation of the success of the therapy. In this feasibility study we used a novel measurement device [Collar Therapy Indicator (CoTI)] to measure the uptake curve of patients undergoing I-131 radioiodine therapy. The CoTI device is a light-weight wearable device that contains two independent gamma radiation detectors that are placed in a collar. By comparing results of thyroid uptake measurements with results obtained with a gamma camera, the precision of the system is demonstrated. Additionally, for three patients the uptake curve is measured during 48 h of admission in the hospital. The presented results demonstrate the feasibility of the new measurement device to measure the uptake curve during radioiodine therapy. (orig.)

A new member of the greater double-collared sunbird complex (Passeriformes: Nectariniidae) from the Eastern Arc Mountains of Africa

DEFF Research Database (Denmark)

Bowie, Rauri C. K.; Fjeldså, Jon; Kiure, Jacob

2016-01-01

a cautious approach and formally describe the Rubeho and Udzungwa greater double-collared sunbird population as a subspecies of Cinnyris whytei. This new sunbird taxon has been recorded only above 1700 m in scrub on the forest/grassland ecotone in a very restricted area in the Rubeho and Udzungwa Highlands...

Influence of edge radius of sintered-carbide tip on roughness of machined surface

Directory of Open Access Journals (Sweden)

Jiří Votava

2013-01-01

Full Text Available Increasing of cutting speed and thus increasing labour productivity is observed as a current trend in engineering production. This effort results to development of new cutting materials which are more capable to resist increased requirements on machined surface as well as operating life of the instrument. Nowadays, the most widely used materials used for cutting instruments are sintered carbides which are alloyed by other metals. The goal of this paper is to analyse change in quality of machined surface depending on the change of cutting conditions. For cutting operation, there were used a milling cutter high-speed steel 90 (HSS and removable sintered-carbide tips with different radius. Steel 12 050 hardened for 17 HRC was used as a machined material. Firstly, hardness of machined as well as machining materials was analysed. Further, metallographic analysis and measurement of microhardness of the individual structure phases was processed. Cutting conditions of both instruments were selected depending on the machined material. Surface roughness indicates the quality of machined surface.

Three-dimensional machining of carbon nanotube forests using water-assisted scanning electron microscope processing

Energy Technology Data Exchange (ETDEWEB)

Rajabifar, Bahram; Maschmann, Matthew R., E-mail: MaschmannM@missouri.edu [Department of Mechanical and Aerospace Engineering, University of Missouri, Columbia, Missouri 65211 (United States); Kim, Sanha; Hart, A. John [Department of Mechanical Engineering and Laboratory for Manufacturing and Productivity, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Slinker, Keith [Materials and Manufacturing Directorate, AFRL/RX, Air Force Research Lab, Ohio 45433 (United States); Universal Technology Corporation, Beavercreek, Ohio 45424 (United States); Ehlert, Gregory J. [Materials and Manufacturing Directorate, AFRL/RX, Air Force Research Lab, Ohio 45433 (United States)

2015-10-05

We demonstrate that vertically aligned carbon nanotubes (CNTs) can be precisely machined in a low pressure water vapor ambient using the electron beam of an environmental scanning electron microscope. The electron beam locally damages the irradiated regions of the CNT forest and also dissociates the water vapor molecules into reactive species including hydroxyl radicals. These species then locally oxidize the damaged region of the CNTs. The technique offers material removal capabilities ranging from selected CNTs to hundreds of cubic microns. We study how the material removal rate is influenced by the acceleration voltage, beam current, dwell time, operating pressure, and CNT orientation. Milled cuts with depths between 0–100 microns are generated, corresponding to a material removal rate of up to 20.1 μm{sup 3}/min. The technique produces little carbon residue and does not disturb the native morphology of the CNT network. Finally, we demonstrate direct machining of pyramidal surfaces and re-entrant cuts to create freestanding geometries.

Three-dimensional machining of carbon nanotube forests using water-assisted scanning electron microscope processing

Science.gov (United States)

Rajabifar, Bahram; Kim, Sanha; Slinker, Keith; Ehlert, Gregory J.; Hart, A. John; Maschmann, Matthew R.

2015-10-01

We demonstrate that vertically aligned carbon nanotubes (CNTs) can be precisely machined in a low pressure water vapor ambient using the electron beam of an environmental scanning electron microscope. The electron beam locally damages the irradiated regions of the CNT forest and also dissociates the water vapor molecules into reactive species including hydroxyl radicals. These species then locally oxidize the damaged region of the CNTs. The technique offers material removal capabilities ranging from selected CNTs to hundreds of cubic microns. We study how the material removal rate is influenced by the acceleration voltage, beam current, dwell time, operating pressure, and CNT orientation. Milled cuts with depths between 0-100 microns are generated, corresponding to a material removal rate of up to 20.1 μm3/min. The technique produces little carbon residue and does not disturb the native morphology of the CNT network. Finally, we demonstrate direct machining of pyramidal surfaces and re-entrant cuts to create freestanding geometries.

Synchronous genetic turnovers across Western Eurasia in Late Pleistocene collared lemmings.

Science.gov (United States)

Palkopoulou, Eleftheria; Baca, Mateusz; Abramson, Natalia I; Sablin, Mikhail; Socha, Paweł; Nadachowski, Adam; Prost, Stefan; Germonpré, Mietje; Kosintsev, Pavel; Smirnov, Nickolay G; Vartanyan, Sergey; Ponomarev, Dmitry; Nyström, Johanna; Nikolskiy, Pavel; Jass, Christopher N; Litvinov, Yuriy N; Kalthoff, Daniela C; Grigoriev, Semyon; Fadeeva, Tatyana; Douka, Aikaterini; Higham, Thomas F G; Ersmark, Erik; Pitulko, Vladimir; Pavlova, Elena; Stewart, John R; Węgleński, Piotr; Stankovic, Anna; Dalén, Love

2016-05-01

Recent palaeogenetic studies indicate a highly dynamic history in collared lemmings (Dicrostonyx spp.), with several demographical changes linked to climatic fluctuations that took place during the last glaciation. At the western range margin of D. torquatus, these changes were characterized by a series of local extinctions and recolonizations. However, it is unclear whether this pattern represents a local phenomenon, possibly driven by ecological edge effects, or a global phenomenon that took place across large geographical scales. To address this, we explored the palaeogenetic history of the collared lemming using a next-generation sequencing approach for pooled mitochondrial DNA amplicons. Sequences were obtained from over 300 fossil remains sampled across Eurasia and two sites in North America. We identified five mitochondrial lineages of D. torquatus that succeeded each other through time across Europe and western Russia, indicating a history of repeated population extinctions and recolonizations, most likely from eastern Russia, during the last 50 000 years. The observation of repeated extinctions across such a vast geographical range indicates large-scale changes in the steppe-tundra environment in western Eurasia during the last glaciation. All Holocene samples, from across the species' entire range, belonged to only one of the five mitochondrial lineages. Thus, extant D. torquatus populations only harbour a small fraction of the total genetic diversity that existed across different stages of the Late Pleistocene. In North American samples, haplotypes belonging to both D. groenlandicus and D. richardsoni were recovered from a Late Pleistocene site in south-western Canada. This suggests that D. groenlandicus had a more southern and D. richardsoni a more northern glacial distribution than previously thought. This study provides significant insights into the population dynamics of a small mammal at a large geographical scale and reveals a rather complex

Prison Field Trips: Can White-Collar Criminals Positively Affect the Ethical and Legal Behavior of Marketing and MBA Students?

Science.gov (United States)

Castleberry, Stephen B.

2007-01-01

Marketing educators bear some responsibility for teaching ethics and legal issues to their students. Visits to white-collar criminals in a federal prison camp are one method of achieving this task. This article develops and empirically assesses ten objectives for such a visit by MBA and undergraduate marketing classes. Undergraduates rated the…

A review of machines and devices to potentize homeopathic medicines.

Science.gov (United States)

Basu, Abhirup; Suresh, Akkihebbal Krishnamurthy; Kane, Shantaram Govind; Bellare, Jayesh Ramesh

2017-11-01

Potentization, consisting of serial dilution and succussion, is a key step in the manufacture of homeopathic medicines. Originally prescribed as a manual process, several attempts at mechanization have been published, patented and even commercialised in order to remove the human element and introduce reproducibility without drudgery. Various machines have been used over the years to prepare homeopathic medicines. Although these machines follow the same principles, i.e. energetically mixing the medicines and diluting them significantly, their mode of operation is different from each other. This review paper surveys the main methods of preparation of homeopathic medicines. The main machines discussed are: Boericke's potentizer, Tyler Kent's instrument, John Alphonse's machine and the fluxion potentizer, which were used in the past, as well as more recent potentizers like arm-and-weight instruments, the K-Tronic potentizer and Quinn's machine. We review the construction and operating principle of each of these machines, along with their advantages and limitations. A scheme for relative performance assessment of these machines is proposed based on the parameters mechanical efficiency, physico-chemical efficiency, turbulence generation, energy dissipation, and accuracy of dilution. Quinn's machine and the arm-and-weight potentizer perform well for generating turbulence due to high impaction forces, while John Alphonse's machine is much more accurate in diluting the homeopathic medicines at every step. Both the commercial potentizers, Quinn's machine and the K-Tronic potentizer, are completely automated and therefore reduce the manual labour and variation in succussive forces during each step, which may produce uniformity in physico-chemical changes within the resulting homeopathic medicines. Copyright © 2017. Published by Elsevier Ltd.

Prediction of material removal rate and surface roughness for wire electrical discharge machining of nickel using response surface methodology

Directory of Open Access Journals (Sweden)

Thangam Chinnadurai

2016-12-01

Full Text Available This study focuses on investigating the effects of process parameters, namely, Peak current (Ip, Pulse on time (Ton, Pulse off time (Toff, Water pressure (Wp, Wire feed rate (Wf, Wire tension (Wt, Servo voltage (Sv and Servo feed setting (Sfs, on the Material Removal Rate (MRR and Surface Roughness (SR for Wire electrical discharge machining (Wire-EDM of nickel using Taguchi method. Response Surface Methodology (RSM is adopted to evolve mathematical relationships between the wire cutting process parameters and the output variables of the weld joint to determine the welding input parameters that lead to the desired optimal wire cutting quality. Besides, using response surface plots, the interaction effects of process parameters on the responses are analyzed and discussed. The statistical software Mini-tab is used to establish the design and to obtain the regression equations. The developed mathematical models are tested by analysis-of-variance (ANOVA method to check their appropriateness and suitability. Finally, a comparison is made between measured and calculated results, which are in good agreement. This indicates that the developed models can predict the responses accurately and precisely within the limits of cutting parameter being used.

Prediction of material removal rate and surface roughness for wire electrical discharge machining of nickel using response surface methodology

International Nuclear Information System (INIS)

Chinnadurai, T.; Vendan, S.A.

2016-01-01

This study focuses on investigating the effects of process parameters, namely, Peak current (Ip), Pulse on time (Ton), Pulse off time (Toff), Water pressure (Wp), Wire feed rate (Wf), Wire tension (Wt), Servo voltage (Sv) and Servo feed setting (Sfs), on the Material Removal Rate (MRR) and Surface Roughness (SR) for Wire electrical discharge machining (Wire-EDM) of nickel using Taguchi method. Response Surface Methodology (RSM) is adopted to evolve mathematical relationships between the wire cutting process parameters and the output variables of the weld joint to determine the welding input parameters that lead to the desired optimal wire cutting quality. Besides, using response surface plots, the interaction effects of process parameters on the responses are analyzed and discussed. The statistical software Mini-tab is used to establish the design and to obtain the regression equations. The developed mathematical models are tested by analysis-of-variance (ANOVA) method to check their appropriateness and suitability. Finally, a comparison is made between measured and calculated results, which are in good agreement. This indicates that the developed models can predict the responses accurately and precisely within the limits of cutting parameter being used. (Author)

Prediction of material removal rate and surface roughness for wire electrical discharge machining of nickel using response surface methodology

Energy Technology Data Exchange (ETDEWEB)

Chinnadurai, T.; Vendan, S.A.

2016-07-01

This study focuses on investigating the effects of process parameters, namely, Peak current (Ip), Pulse on time (Ton), Pulse off time (Toff), Water pressure (Wp), Wire feed rate (Wf), Wire tension (Wt), Servo voltage (Sv) and Servo feed setting (Sfs), on the Material Removal Rate (MRR) and Surface Roughness (SR) for Wire electrical discharge machining (Wire-EDM) of nickel using Taguchi method. Response Surface Methodology (RSM) is adopted to evolve mathematical relationships between the wire cutting process parameters and the output variables of the weld joint to determine the welding input parameters that lead to the desired optimal wire cutting quality. Besides, using response surface plots, the interaction effects of process parameters on the responses are analyzed and discussed. The statistical software Mini-tab is used to establish the design and to obtain the regression equations. The developed mathematical models are tested by analysis-of-variance (ANOVA) method to check their appropriateness and suitability. Finally, a comparison is made between measured and calculated results, which are in good agreement. This indicates that the developed models can predict the responses accurately and precisely within the limits of cutting parameter being used. (Author)

[A new machinability test machine and the machinability of composite resins for core built-up].

Science.gov (United States)

Iwasaki, N

2001-06-01

A new machinability test machine especially for dental materials was contrived. The purpose of this study was to evaluate the effects of grinding conditions on machinability of core built-up resins using this machine, and to confirm the relationship between machinability and other properties of composite resins. The experimental machinability test machine consisted of a dental air-turbine handpiece, a control weight unit, a driving unit of the stage fixing the test specimen, and so on. The machinability was evaluated as the change in volume after grinding using a diamond point. Five kinds of core built-up resins and human teeth were used in this study. The machinabilities of these composite resins increased with an increasing load during grinding, and decreased with repeated grinding. There was no obvious correlation between the machinability and Vickers' hardness; however, a negative correlation was observed between machinability and scratch width.

A Review on Parametric Analysis of Magnetic Abrasive Machining Process

Science.gov (United States)

Khattri, Krishna; Choudhary, Gulshan; Bhuyan, B. K.; Selokar, Ashish

2018-03-01

The magnetic abrasive machining (MAM) process is a highly developed unconventional machining process. It is frequently used in manufacturing industries for nanometer range surface finishing of workpiece with the help of Magnetic abrasive particles (MAPs) and magnetic force applied in the machining zone. It is precise and faster than conventional methods and able to produce defect free finished components. This paper provides a comprehensive review on the recent advancement of MAM process carried out by different researcher till date. The effect of different input parameters such as rotational speed of electromagnet, voltage, magnetic flux density, abrasive particles size and working gap on the performances of Material Removal Rate (MRR) and surface roughness (Ra) have been discussed. On the basis of review, it is observed that the rotational speed of electromagnet, voltage and mesh size of abrasive particles have significant impact on MAM process.

Machining of AISI D2 Tool Steel with Multiple Hole Electrodes by EDM Process

Science.gov (United States)

Prasad Prathipati, R.; Devuri, Venkateswarlu; Cheepu, Muralimohan; Gudimetla, Kondaiah; Uzwal Kiran, R.

2018-03-01

In recent years, with the increasing of technology the demand for machining processes is increasing for the newly developed materials. The conventional machining processes are not adequate to meet the accuracy of the machining of these materials. The non-conventional machining processes of electrical discharge machining is one of the most efficient machining processes is being widely used to machining of high accuracy products of various industries. The optimum selection of process parameters is very important in machining processes as that of an electrical discharge machining as they determine surface quality and dimensional precision of the obtained parts, even though time consumption rate is higher for machining of large dimension features. In this work, D2 high carbon and chromium tool steel has been machined using electrical discharge machining with the multiple hole electrode technique. The D2 steel has several applications such as forming dies, extrusion dies and thread rolling. But the machining of this tool steel is very hard because of it shard alloyed elements of V, Cr and Mo which enhance its strength and wear properties. However, the machining is possible by using electrical discharge machining process and the present study implemented a new technique to reduce the machining time using a multiple hole copper electrode. In this technique, while machining with multiple holes electrode, fin like projections are obtained, which can be removed easily by chipping. Then the finishing is done by using solid electrode. The machining time is reduced to around 50% while using multiple hole electrode technique for electrical discharge machining.

In-situ Decolorization of Residual Dye Effluent in Textile Jet Dyeing Machine by Ozone

Directory of Open Access Journals (Sweden)

Irfan Ahmed Shaikh

2014-12-01

Full Text Available In this study, a new idea of decolourization was investigated in which residual dyeing effluent from textile dyeing process was treated using O3 in the same machine where it was generated. The novelty comes from the idea of doing dyeing and treatment simultaneously. At the completion of dyeing process, O3 gas was injected directly into the machine to remove colour and COD from the wastewater. To evaluate the effectiveness of new method, pilot-scale studies were performed, and decolourization of residual dyeing effluents containing C.I. Reactive Orange 7, C.I. Reactive Blue 19, and C.I. Reactive Black 5 was carried out in specially built textile jet dyeing machine. The results showed that almost 100% colour removal and 90% COD reduction were achieved when process conditions such as pH, dye concentration (mg/L, ozone production rate (g/hr, and temperature were optimized. The study concludes that new method has a great potential to eliminate the need of a separate end-of-the-pipe wastewater treatment system, thus offering an on-site and cost-effective solution.

Gender differences in work–home interplay and symptom perception among Swedish white‐collar employees

Science.gov (United States)

Berntsson, L; Lundberg, U; Krantz, G

2006-01-01

Objective To analyse gender differences in paid and unpaid workload and symptoms in matched groups of Swedish white‐collar workers with children. Design and setting Paid and unpaid workload and perceived stress from paid work, conflict between demands and control over household work were measured by a total workload (TWL) questionnaire. Some symptoms were rated with regard to frequency and severity as a measure of health. Cross‐sectional analyses were performed. Participants Matched groups of male (n = 440) and female (n = 529) well‐educated white‐collar workers in full‐time employment, aged 32–58 years and living with children in the home. Results Women in higher positions in Sweden are healthier than the average population of women, but report more symptoms than men in the same position as well as more stress from paid work, more conflict between demands and a greater TWL. However, women also reported more control over household duties and TWL was not associated with more symptoms. The men were mainly focused on their paid work role and perhaps even more so than men in the general population as they were fairly resistant to feelings of conflicting demands. Conclusion Even among matched groups of full‐time employed, well‐educated men and women, traditional gender differences in division of responsibilities and time allocation were found. Even though the women were healthy at this stage, they might risk future ill health, owing to high workload, stress and feelings of conflicting demands. PMID:17108304

Workload, work stress, and sickness absence in Swedish male and female white-collar employees.

Science.gov (United States)

Krantz, Gunilla; Lundberg, Ulf

2006-01-01

This study aimed to analyse, in a homogeneous population of highly educated men and women, gender differences in self-reported sickness absence as related to paid and unpaid work and combinations of these (double exposure), as well as to perceived work stress and work-home conflict, i.e. conflict between demands from the home and work environment. A total of 743 women and 596 men, full-time working white-collar employees randomly selected from the general Swedish population aged 32-58, were assessed by a Swedish total workload instrument. The influence of conditions in paid and unpaid work and combinations of these on self-reported sickness absence was investigated by multivariate regression analyses. Analysis of variance (ANOVA) was used to assess differences between men and women. Overtime was associated with lower sickness absence, not only for men but also for women, and a double-exposure situation did not increase the risk of sick leave. Contrary to what is normally seen, conflict between demands did not emerge as a risk factor for sickness absence for women, but for men. Our assumption that sickness absence patterns would be more similar for white-collar men and women than for the general population was not confirmed. However, the women working most hours were also the least sick-listed and assumed less responsibility for household chores. These women were mainly in top-level positions and therefore we conclude that men and women in these high-level positions seem to share household burdens more evenly, but they can also afford to employ someone to assist in the household.

AAA+ Machines of Protein Destruction in Mycobacteria.

Science.gov (United States)

Alhuwaider, Adnan Ali H; Dougan, David A

2017-01-01

The bacterial cytosol is a complex mixture of macromolecules (proteins, DNA, and RNA), which collectively are responsible for an enormous array of cellular tasks. Proteins are central to most, if not all, of these tasks and as such their maintenance (commonly referred to as protein homeostasis or proteostasis) is vital for cell survival during normal and stressful conditions. The two key aspects of protein homeostasis are, (i) the correct folding and assembly of proteins (coupled with their delivery to the correct cellular location) and (ii) the timely removal of unwanted or damaged proteins from the cell, which are performed by molecular chaperones and proteases, respectively. A major class of proteins that contribute to both of these tasks are the AAA+ (ATPases associated with a variety of cellular activities) protein superfamily. Although much is known about the structure of these machines and how they function in the model Gram-negative bacterium Escherichia coli , we are only just beginning to discover the molecular details of these machines and how they function in mycobacteria. Here we review the different AAA+ machines, that contribute to proteostasis in mycobacteria. Primarily we will focus on the recent advances in the structure and function of AAA+ proteases, the substrates they recognize and the cellular pathways they control. Finally, we will discuss the recent developments related to these machines as novel drug targets.

The Economic Effects of Cognitive and Educational Differences Among Low-Ability and Blue-Collar Origin Men: A Comparative Analysis.

Science.gov (United States)

Olneck, Michael R.

This study used five data sets to investigate the effects of measured cognitive skills on educational attainment, and the effects of cognitive skills and educational attainment on occupational status and earning among men with low test scores, as compared to men with high test scores, and among men with blue-collar fathers, as compared to men with…

Classifying images using restricted Boltzmann machines and convolutional neural networks

Science.gov (United States)

Zhao, Zhijun; Xu, Tongde; Dai, Chenyu

2017-07-01

To improve the feature recognition ability of deep model transfer learning, we propose a hybrid deep transfer learning method for image classification based on restricted Boltzmann machines (RBM) and convolutional neural networks (CNNs). It integrates learning abilities of two models, which conducts subject classification by exacting structural higher-order statistics features of images. While the method transfers the trained convolutional neural networks to the target datasets, fully-connected layers can be replaced by restricted Boltzmann machine layers; then the restricted Boltzmann machine layers and Softmax classifier are retrained, and BP neural network can be used to fine-tuned the hybrid model. The restricted Boltzmann machine layers has not only fully integrated the whole feature maps, but also learns the statistical features of target datasets in the view of the biggest logarithmic likelihood, thus removing the effects caused by the content differences between datasets. The experimental results show that the proposed method has improved the accuracy of image classification, outperforming other methods on Pascal VOC2007 and Caltech101 datasets.

Machinability of lithium disilicate glass ceramic in in vitro dental diamond bur adjusting process.

Science.gov (United States)

Song, Xiao-Fei; Ren, Hai-Tao; Yin, Ling

2016-01-01

Esthetic high-strength lithium disilicate glass ceramics (LDGC) are used for monolithic crowns and bridges produced in dental CAD/CAM and oral adjusting processes, which machinability affects the restorative quality. A machinability study has been made in the simulated oral clinical machining of LDGC with a dental handpiece and diamond burs, regarding the diamond tool wear and chip control, machining forces and energy, surface finish and integrity. Machining forces, speeds and energy in in vitro dental adjusting of LDGC were measured by a high-speed data acquisition and force sensor system. Machined LDGC surfaces were assessed using three-dimensional non-contact chromatic confocal optical profilometry and scanning electron microscopy (SEM). Diamond bur morphology and LDGC chip shapes were also examined using SEM. Minimum tool wear but significant LDGC chip accumulations were found. Machining forces and energy significantly depended on machining conditions (pceramics (pceramics (pceramics. Surface roughness for machined LDGC was comparable for other glass ceramics. The removal mechanisms of LDGC were dominated by penetration-induced brittle fracture and shear-induced plastic deformation. Unlike most other glass ceramics, distinct intergranular and transgranular fractures of lithium disilicate crystals were found in LDGC. This research provides the fundamental data for dental clinicians on the machinability of LDGC in intraoral adjustments. Copyright © 2015 Elsevier Ltd. All rights reserved.

Cap’n’collar differentiates the mandible from the maxilla in the beetle Tribolium castaneum

Science.gov (United States)

2012-01-01

Background The biting mandible of the arthropods is thought to have evolved in the ancestor of the insects, crustaceans and myriapods: the Mandibulata. A unique origin suggests a common set of developmental genes will be required to pattern the mandible in different arthropods. To date we have functional studies on patterning of the mandibular segment of Drosophila melanogaster showing in particular the effects of the gene cap’n’collar (cnc), however, the dipteran head is far from representative of insects or of more distantly related mandibulates; Drosophila does not even possess a mandibular appendage. To study the development of a more representative insect mandible, we chose the red flour beetle Tribolium castaneum and investigated the function of the Tribolium orthologs of cap’n’collar (Tc-cnc) and the Hox gene Deformed (Tc-Dfd). In order to determine the function of Tc-cnc and Tc-Dfd, transcripts were knocked down by maternal RNA interference (RNAi). The effects of gene knockdown were examined in the developing embryos and larvae. The effect of Tc-cnc and Tc-Dfd knockdown on the expression of other genes was determined by using in situ hybridization on Tribolium embryos. Results Our analyses show that Tc-cnc is required for specification of the identity of the mandibular segment of Tribolium and differentiates the mandible from maxillary identity. Loss of Tc-cnc function results in a transformation of the mandible to maxillary identity as well as deletion of the labrum. Tc-Dfd and the Tribolium homolog of proboscipedia (Tc-mxp = maxillopedia), Hox genes that are required to pattern the maxillary appendage, are expressed in a maxilla-like manner in the transformed mandible. Tribolium homologs of paired (Tc-prd) and Distal-less (Tc-Dll) that are expressed in the endites and telopodites of embryonic appendages are also expressed in a maxilla-like manner in the transformed mandible. We also show that Tc-Dfd is required to activate the collar of Tc

Dog-appeasing pheromone collars reduce sound-induced fear and anxiety in beagle dogs: a placebo-controlled study.

Science.gov (United States)

Landsberg, G M; Beck, A; Lopez, A; Deniaud, M; Araujo, J A; Milgram, N W

2015-09-12

The objective of the study was to assess the effects of a dog-appeasing pheromone (DAP) collar in reducing sound-induced fear and anxiety in a laboratory model of thunderstorm simulation. Twenty-four beagle dogs naïve to the current test were divided into two treatment groups (DAP and placebo) balanced on their fear score in response to a thunderstorm recording. Each group was then exposed to two additional thunderstorm simulation tests on consecutive days. Dogs were video-assessed by a trained observer on a 6-point scale for active, passive and global fear and anxiety (combined). Both global and active fear and anxiety scores were significantly improved during and following thunder compared with placebo on both test days. DAP significantly decreased global fear and anxiety across 'during' and 'post' thunder times when compared with baseline. There was no significant improvement in the placebo group from baseline on the test days. In addition, the DAP group showed significantly greater use of the hide box at any time with increased exposure compared with the placebo group. The DAP collar reduced the scores of fear and anxiety, and increased hide use in response to a thunder recording, possibly by counteracting noise-related increased reactivity. British Veterinary Association.

Testing of Anesthesia Machines and Defibrillators in Healthcare Institutions.

Science.gov (United States)

Gurbeta, Lejla; Dzemic, Zijad; Bego, Tamer; Sejdic, Ervin; Badnjevic, Almir

2017-09-01

To improve the quality of patient treatment by improving the functionality of medical devices in healthcare institutions. To present the results of the safety and performance inspection of patient-relevant output parameters of anesthesia machines and defibrillators defined by legal metrology. This study covered 130 anesthesia machines and 161 defibrillators used in public and private healthcare institutions, during a period of two years. Testing procedures were carried out according to international standards and legal metrology legislative procedures in Bosnia and Herzegovina. The results show that in 13.84% of tested anesthesia machine and 14.91% of defibrillators device performance is not in accordance with requirements and should either have its results be verified, or the device removed from use or scheduled for corrective maintenance. Research emphasizes importance of independent safety and performance inspections, and gives recommendations for the frequency of inspection based on measurements. Results offer implications for adequacy of preventive and corrective maintenance performed in healthcare institutions. Based on collected data, the first digital electronical database of anesthesia machines and defibrillators used in healthcare institutions in Bosnia and Herzegovina is created. This database is a useful tool for tracking each device's performance over time.

Factors associated with utilization of traditional Chinese medicine by white collar foreign workers living in Taiwan.

Science.gov (United States)

Daly, Maria; Tai, Chen-Jei; Deng, Chung-Yeh; Chien, Li-Yin

2009-01-14

Traditional Chinese medicine (TCM) has remained an integral part of Chinese culture and society for thousands of years. In Taiwan TCM is a recognized element of its National Health Insurance Scheme. However, there is no knowledge about how TCM is accessed by foreign workers from a non-Asian cultural background. The objectives of this study were to investigate the prevalence and patterns of TCM use among non-Asian white-collar workers living in Taiwan, and examine factors likely to influence their use of TCM. This study applied a cross-sectional survey design. A total of 207 white-collar foreign workers of a non-Asian background currently holding National Health Insurance cards who had lived in Taiwan for 4 months or more participated in this study. The prevalence of TCM use was 45%. The most frequently used therapies were traditional Chinese herbs/medicine and acupuncture. Factors indicating the likelihood of TCM usage were age 31-40 years, visit to an allopathic medical doctor in the last year, ability to read Chinese, having a friend or family member available to assist in the use of TCM, and access to information about TCM services available in Taiwan. Utilization of TCM by people of a non-Asian background living in Taiwan appears to be most influenced by enabling factors including language ability, access to information, and informal reference persons.

Sodium removal from the grapples of the fuel handling facility of Joyo

Energy Technology Data Exchange (ETDEWEB)

Mukaibo, R; Matsuno, Y; Sato, I; Yoneda, Y; Sato, H [O-arai Engineering Centre, PNC, Ibaraki-ken, Tokio (Japan)

1978-08-01

Sodium removal from the grapples of the fuel handling facility of 'JOYO' is done in alcohol. The operations of the cleaning facility started as the functional tests of the fuel handling facility began. Since then, criticality test and low power tests had been done and during this period, sodium removal from the grapples, after a certain amount of time in use, were done. In order to lessen the time for the cleaning process for the grapples of the machines inside the containment vessel, demineralized water concentration in the alcohol was gained to as much as 10% and good results were obtained. On the other hand, there were very small amounts of sodium on the grapples of the machine used outside the containment vessel and direct charging of demineralized water into the cleaning pot was done experimentally, also with good results. In this report, the sodium removal experience of the grapples before power up tests and some remarks on the improvements of the facility for the future are presented. (author)

The Machine within the Machine

CERN Multimedia

Katarina Anthony

2014-01-01

Although Virtual Machines are widespread across CERN, you probably won't have heard of them unless you work for an experiment. Virtual machines - known as VMs - allow you to create a separate machine within your own, allowing you to run Linux on your Mac, or Windows on your Linux - whatever combination you need.   Using a CERN Virtual Machine, a Linux analysis software runs on a Macbook. When it comes to LHC data, one of the primary issues collaborations face is the diversity of computing environments among collaborators spread across the world. What if an institute cannot run the analysis software because they use different operating systems? "That's where the CernVM project comes in," says Gerardo Ganis, PH-SFT staff member and leader of the CernVM project. "We were able to respond to experimentalists' concerns by providing a virtual machine package that could be used to run experiment software. This way, no matter what hardware they have ...

Penerapan Support Vector Machine (SVM untuk Pengkategorian Penelitian

Directory of Open Access Journals (Sweden)

Fithri Selva Jumeilah

2017-07-01

Full Text Available Research every college will continue to grow. Research will be stored in softcopy and hardcopy. The preparation of the research should be categorized in order to facilitate the search for people who need reference. To categorize the research, we need a method for text mining, one of them is with the implementation of Support Vector Machines (SVM. The data used to recognize the characteristics of each category then it takes secondary data which is a collection of abstracts of research. The data will be pre-processed with several stages: case folding converts all the letters into lowercase, stop words removal removal of very common words, tokenizing discard punctuation, and stemming searching for root words by removing the prefix and suffix. Further data that has undergone preprocessing will be converted into a numerical form with for the term weighting stage that is the weighting contribution of each word. From the results of term weighting then obtained data that can be used for data training and test data. The training process is done by providing input in the form of text data that is known to the class or category. Then by using the Support Vector Machines algorithm, the input data is transformed into a rule, function, or knowledge model that can be used in the prediction process. From the results of this study obtained that the categorization of research produced by SVM has been very good. This is proven by the results of the test which resulted in an accuracy of 90%.

Preliminary study on rotary ultrasonic machining of Bk-7 optical glass rod

International Nuclear Information System (INIS)

Hamzah, E.; Izman, S.; Khoo, C.Y.; Zainal Abidin, N.N.

2007-01-01

This paper presents an experimental observation on rotary ultrasonic machining (RUM) of BK7 optical glass rod. BK7 is a common technical optical glass for high quality optical components due to its high linear optical transmission in the visible range and is chemically stable. RUM is a hybrid machining process that combines the material removal mechanisms of diamond grinding and ultrasonic machining (USM) and it is non-thermal, non-chemical, creates no change in the microstructure, chemical or physical properties of the work piece. In the RUM, a controlled static load is applied to the rotating core drill with metal bonded diamond abrasive and is ultrasonically vibrated in the axial direction. A water-soluble coolant was used to cool the tool and sample during machining processes. By using DOE (Design of Experiment) approach, the effect of spindle speed and feed rate to the ultrasonic machinability had been developed. The main effects and two-factor interactions of process parameters (spindle speed) and feed rate) on output variables (MRR, surface roughness, opaqueness, chipping thickness and chipping size) are studied. (author)

Factors associated with utilization of traditional Chinese medicine by white collar foreign workers living in Taiwan

OpenAIRE

Deng Chung-Yeh; Tai Chen-Jei; Daly Maria; Chien Li-Yin

2009-01-01

Abstract Background Traditional Chinese medicine (TCM) has remained an integral part of Chinese culture and society for thousands of years. In Taiwan TCM is a recognized element of its National Health Insurance Scheme. However, there is no knowledge about how TCM is accessed by foreign workers from a non-Asian cultural background. The objectives of this study were to investigate the prevalence and patterns of TCM use among non-Asian white-collar workers living in Taiwan, and examine factors l...

Machine site preparation improves seedling performance on a high-elevation site in southwest Oregon

International Nuclear Information System (INIS)

McNabb, D.H.; Baker-Katz, K.; Tesch, S.D.

1993-01-01

Douglas-fir (Pseudotsuga menziesii) seedlings planted on areas receiving one of four site-preparation treatments (scarify, scarify/till, soil removal, and soil removal/till) and on unprepared control areas were compared for 5 yr at a high-elevation, nutrient-poor site in the western Siskiyou Mountains of southwest Oregon. Fifth-year survival of seedlings was at least 85% among machine-prepared plots, compared to 42% on control plots. Cover of competing vegetation remained less than 25% during the period for all machine treatments. In contrast, vegetation cover on control plots was 30% at the time of planting and increased to nearly 75% after 5 yr. Competing vegetation clearly impeded seedling performance. The effects of unusually droughty conditions at the time of planting in 1982 were examined further by interplanting additional seedlings in the soil-removal treatment in 1985. The interplanting was followed by more normal spring precipitation, and seedlings grew better over 5 yr than those planted in 1982. The slow recovery of competing vegetation and generally poor seedling growth on all treatments during both planting years are attributed to low soil fertility

Methodes de compensation des erreurs d'usinage utilisant la mesure sur machines-outils

Science.gov (United States)

Guiassa, Rachid

On-machine measurement process is used to inspect the part immediately after the cut without part removal and additional setups. It detects the machining defects visible to the machine tool. The system machine-tool-part deflection and the cutting tool dimension inaccuracy are the most important sources of these defects. The machined part can be inspected, at the semi-finishing cut level to identify systematic defects that may occur later at the finishing cut. Therefore, corrective actions can be derived to anticipate the expected error in order to produce a part with acceptable accuracy. For industrial profitability, the measurement and the compensation tasks must be done under the closed door machining requirement without human interventions. This thesis aims to develop mathematical models that use the data inspection of previous cuts to formulate the compensation of the finishing-cut. The goal of the compensation is to anticipate the expected error which is identified under two components. One is independent on the depth of cut and is related to the cutting tool dimension such as the wear. The other is dependent on the cutting depth such as the deflection. A general model is presented which relies solely on-machine probing data from semi-finishing cuts to compensate the final cut. A variable cutting compliance coefficient relates the total system deflection to the depth of cut in multi-cut process. It is used to estimate the compensation of the tool path. The model is able to take into account the effect of the cutting depth variation and the material removal in the estimation of the error at the finishing-cut. In order to generate the continuous compensated tool path from discrete measurements, a B-Spline deformation technique is adapted to the available data and applied to compute the compensated tool path according to a restricted number of discrete compensation vectors. The results show that the on-machine probed errors can be significantly reduced using the

Influence of Cryopreservation Solution on the In Vitro Culture of Skin Tissues Derived from Collared Peccary (Pecari tajacu Linnaeus, 1758).

Science.gov (United States)

Borges, Alana A; Lira, Gabriela P O; Nascimento, Lucas E; Queiroz Neta, Luiza B; Santos, Maria V O; Oliveira, Moacir F; Silva, Alexandre R; Pereira, Alexsandra F

2018-04-01

Skin vitrification is a promising and alternative tool for the conservation of biodiversity, especially for wild mammals, such as collared peccaries. Several factors can affect the success of this procedure, such as the cryoprotectant solution used. Therefore, this study was carried out to compare the efficiency of various vitrification solutions for recovery of viable cells after in vitro culture of cryopreserved skin tissues derived from the collared peccary, aiming to study the application in biobanking, where cellular use is not immediately required. Then, Dulbecco's modified Eagle's medium (DMEM) composed of 2.2 g/L sodium bicarbonate and 10% fetal bovine serum (FBS) was supplemented with 3.0 M ethylene glycol (EG) or 3.0 M dimethyl sulfoxide (DMSO) or 1.5 M EG plus 1.5 M DMSO with or without sucrose (SUC; 0.25 M) to produce six solutions for solid-surface vitrification. After warming, skin tissues were cultured in vitro and recovered cells were analyzed for morphology, adhesion, subconfluence, and proliferative activity for developing the growth curve and determining the population doubling time (PDT), and viability by Trypan Blue. The vitrification did not alter the ability of the tissues to adhere to the culture dish, as well as the day of all explants with cell growth, subconfluence samples, subconfluence total time, and PDT (p > 0.05). Moreover, independent of the cryoprotectant solution used, the vitrification altered the day of all attached explants (p  0.05). Additionally, for viability after the third passage, only the EG-SUC group maintained the cell quality (88.3%), when compared with the nonvitrified (97.8%, p > 0.05). In conclusion, DMEM with 10% FBS, 3.0 M EG, and 0.25 M sucrose was the most efficient solution for vitrifying collared peccary skin tissues, leading to the in vitro culture of viable cells.

Effect of Machining Velocity in Nanoscale Machining Operations

International Nuclear Information System (INIS)

Islam, Sumaiya; Khondoker, Noman; Ibrahim, Raafat

2015-01-01

The aim of this study is to investigate the generated forces and deformations of single crystal Cu with (100), (110) and (111) crystallographic orientations at nanoscale machining operation. A nanoindenter equipped with nanoscratching attachment was used for machining operations and in-situ observation of a nano scale groove. As a machining parameter, the machining velocity was varied to measure the normal and cutting forces. At a fixed machining velocity, different levels of normal and cutting forces were generated due to different crystallographic orientations of the specimens. Moreover, after machining operation percentage of elastic recovery was measured and it was found that both the elastic and plastic deformations were responsible for producing a nano scale groove within the range of machining velocities from 250-1000 nm/s. (paper)

Effect of changing polarity of graphite tool/ Hadfield steel workpiece couple on machining performances in die sinking EDM

Directory of Open Access Journals (Sweden)

Özerkan Haci Bekir

2017-01-01

Full Text Available In this study, machining performance ouput parameters such as machined surface roughness (SR, material removal rate (MRR, tool wear rate (TWR, were experimentally examined and analyzed with the diversifying and changing machining parameters in (EDM. The processing parameters (input par. of this research are stated as tool material, peak current (I, pulse duration (ton and pulse interval (toff. The experimental machinings were put into practice by using Hadfield steel workpiece (prismatic and cylindrical graphite electrodes with kerosene dielectric at different machining current, polarity and pulse time settings. The experiments have shown that the type of tool material, polarity (direct polarity forms higher MRR, SR and TWR, current (high current lowers TWR and enhances MRR, TWR and pulse on time (ton=48□s is critical threshold value for MRR and TWR were influential on machining performance in electrical discharge machining.

Effect of double false pulses in calibrated neutron coincidence collar during measuring time-correlated neutrons from PuBe neutron sources

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Tam Cong, E-mail: tam.nguyen.cong@energia.mta.hu; Huszti, Jozsef; Nguyen, Quan Van

2015-09-01

Effect of double false pulses of preamplifiers in neutron coincidence collar was investigated to explain non-parallel shape of calibrated D/S–M{sub Pu} curves of two commercial neutron coincidence collars, JCC-31 and JCC-13. Two curves, which were constructed from D/S ratio (doubles and singles count rate), and Pu content M{sub Pu}, of the same set of secondary standard PuBe neutron sources, should be parallel. Non-parallelism rises doubt about usability of the method based on this curve for determination of Pu content in PuBe neutron sources. We have shown in three steps that the problem originates from double false pulses of preamplifiers in JCC-13. First we used a pulse train diagram for analyzing the non-parallel shape, second we used Rossi-Alpha distribution measured by pulse train recorder developed in our institute and finally, we investigated the effect of inserted noise pulses. This implies a new type of QA test option in traditional multiplicity shift registers for excluding presence of double false pulses.

Development on the ex-vessel transfer machine for Monju, (1)

International Nuclear Information System (INIS)

Inoue, Takashi; Kinuta, Kenji; Tomita, Takaaki

1980-01-01

As for the fast breeder reactors being developed as the national project, the construction of the prototype reactor ''Monju'' is started in 1980 based on the results of development of the experimental reactor ''Joyo''. In the fuel-handling facility, the development of which is promoted by Fuji Electric Co., Ltd., the development of the fuel transfer machines which take out and charge the fuel for the reactors and carry out the transport between fuel storage facilities is important subject. In this paper, the outline of the development of a fuel transfer machine is described, centering around the handling of fuel in sodium and the removal of the heat of spent fuel. ''Monju'' with 300 MW electric output is being developed for the purposes of putting fast breeder reactors in practical use, increasing plant power output, improving the rate of operation, and securing the safety. Plutonium is used as the fuel, and liquid metallic sodium is used as the coolant in fast breeder reactors, accordingly the fuel must be handled safely in gas-tight, shielded vessels while it is cooled, and securely in sodium and sodium cover gas by remote operation. Gripper, gripper-driving mechanism, coffin, movable block, door valves, cooling system and carriage compose the fuel transfer machine, and these are described. The main results of development and the tests for the development, such as the trial manufacture of gripper and decay heat removal test, are reported. (Kako, I.)

A mathematical model for surface roughness of fluidic channels produced by grinding aided electrochemical discharge machining (G-ECDM

Directory of Open Access Journals (Sweden)

Ladeesh V. G.

2017-01-01

Full Text Available Grinding aided electrochemical discharge machining is a hybrid technique, which combines the grinding action of an abrasive tool and thermal effects of electrochemical discharges to remove material from the workpiece for producing complex contours. The present study focuses on developing fluidic channels on borosilicate glass using G-ECDM and attempts to develop a mathematical model for surface roughness of the machined channel. Preliminary experiments are conducted to study the effect of machining parameters on surface roughness. Voltage, duty factor, frequency and tool feed rate are identified as the significant factors for controlling surface roughness of the channels produced by G-ECDM. A mathematical model was developed for surface roughness by considering the grinding action and thermal effects of electrochemical discharges in material removal. Experiments are conducted to validate the model and the results obtained are in good agreement with that predicted by the model.

Fatal Phenol Toxicity Following Attempted Tattoo Removal.

Science.gov (United States)

Li, Zhen; Zhang, Huang; Li, Shu-Hua; Byard, Roger W

2016-07-01

Tattoo removal is increasingly required as the number of, particularly young, people acquiring tattoos is increasing. A 21-year-old man is reported who underwent attempted removal of large dragon tattoo utilizing a tattoo machine that injected a phenol-containing solution. At the end of the 3-h procedure, he collapsed and died. At autopsy, large areas of white skin discoloration with focal necrosis and sloughing were present overlying areas of previous tattooing. Histological examination showed collections of eosinophilic fluid with a minimal chronic inflammatory infiltrate in better preserved areas, with focal areas of dermal necrosis. Toxicology was positive for phenol in cardiac blood and liver tissue. There were no underlying organic disease or injuries present which could have caused or contributed to death. This idiosyncratic method of tattoo removal involving subcutaneous injection of phenol had resulted in death most likely from cardiotoxicity. © 2016 American Academy of Forensic Sciences.

Post-Removal Examination of GTF Cathode No.2

International Nuclear Information System (INIS)

Kirby, R.

2005-01-01

This photo-cathode (PC), GTF Cathode No.2, was removed from the GTF in October, 2000. It was characterized in September, 1999 by G. Mulhollan and me (Report entitled ''A Brief Report on a Brief Examination of the Electropolished GTF Cathode'', LCLS-TN-99-10). The cathode conditions and results of that exam were: (1) The cathode was conventionally machined and cleaned in the SLAC Plating Shop. (2) The machining process left a central defect (400 microns diameter) which was not removed by electropolishing. (3) The electropolished surface was ''orange-peeled'', typical of excessive polishing. (4) Secondary electron microscopy (SEM) examination showed numerous 10 micron-diameter etch pits and a small number of copper surface particles. Operation of this cathode in the GTF exhibited ''holloW--beam'' behavior, suggesting that the central defect may have been responsible for non-normal emergence of the photo-emitted beam. No laser cleaning of the cathode was done, so all arc features are due to breakdowns. Post-removal analysis consisted of loW--magnification digital camera pictures (taken with glancing-incidence tungsten white light illumination, to emphasize particles/pitting) and SEM. All images are available in digital (TIFF) form. Also available is a Power Point presentation of the results. Contact me for either. These image files are high-resolution and, thus, large in size. A 200K loW--resolution contact sheet of a few images is attached to this report. Images are referred to by file name

Source-specific social support and circulating inflammatory markers among white-collar employees.

Science.gov (United States)

Nakata, Akinori; Irie, Masahiro; Takahashi, Masaya

2014-06-01

Despite known beneficial effects of social support on cardiovascular health, the pathway through which sources of support (supervisor, coworkers, family/friends) influence inflammatory markers is not completely understood. We investigated the independent and moderating associations between social support and inflammatory markers. A total of 137 male white-collar employees underwent a blood draw for measurement of high-sensitive C-reactive protein (hs-CRP), interleukin-6 (IL-6), tumor necrosis factor alpha (TNF-α), monocyte and leukocyte counts, and completed a questionnaire on social support. Multivariable linear regression analyses controlling for covariates revealed that supervisor support was inversely associated with IL-6 (β = -0.24, p markers. Social support from the immediate supervisor may be a potential mechanism through which social support exerts beneficial effects on inflammatory markers in working men.

Prediction of Machine Tool Condition Using Support Vector Machine

International Nuclear Information System (INIS)

Wang Peigong; Meng Qingfeng; Zhao Jian; Li Junjie; Wang Xiufeng

2011-01-01

Condition monitoring and predicting of CNC machine tools are investigated in this paper. Considering the CNC machine tools are often small numbers of samples, a condition predicting method for CNC machine tools based on support vector machines (SVMs) is proposed, then one-step and multi-step condition prediction models are constructed. The support vector machines prediction models are used to predict the trends of working condition of a certain type of CNC worm wheel and gear grinding machine by applying sequence data of vibration signal, which is collected during machine processing. And the relationship between different eigenvalue in CNC vibration signal and machining quality is discussed. The test result shows that the trend of vibration signal Peak-to-peak value in surface normal direction is most relevant to the trend of surface roughness value. In trends prediction of working condition, support vector machine has higher prediction accuracy both in the short term ('One-step') and long term (multi-step) prediction compared to autoregressive (AR) model and the RBF neural network. Experimental results show that it is feasible to apply support vector machine to CNC machine tool condition prediction.

Modelling of destructive ability of water-ice-jet while machine processing of machine elements

Directory of Open Access Journals (Sweden)

Burnashov Mikhail

2017-01-01

Full Text Available This paper represents the classification of the most common contaminants, appearing on the surfaces of machine elements after a long-term service.The existing well-known surface cleaning methods are described and analyzed in the framework of this paper. The article is intended to provide the reader with an understanding of the process of cleaning and removing contamination from machine elements surface by means of water-ice-jet with preprepared beforehand particles, as well as the process of water-ice-jet formation. The paper deals with the description of such advantages of this method as low costs, wastelessness, high quality of the surface, undergoing processing, minimization of harmful impact upon environment and eco-friendliness, which makes it differ radically from formerly known methods. The scheme of interection between the surface and ice particle is represented. A thermo-physical model of destruction of contaminants by means of a water-ice-jet cleaning technology was developed on its basis. The thermo-physical model allows us to make setting of processing mode and the parameters of water-ice-jet scientifically substantiated and well-grounded.

Environmentally Friendly Machining

CERN Document Server

Dixit, U S; Davim, J Paulo

2012-01-01

Environment-Friendly Machining provides an in-depth overview of environmentally-friendly machining processes, covering numerous different types of machining in order to identify which practice is the most environmentally sustainable. The book discusses three systems at length: machining with minimal cutting fluid, air-cooled machining and dry machining. Also covered is a way to conserve energy during machining processes, along with useful data and detailed descriptions for developing and utilizing the most efficient modern machining tools. Researchers and engineers looking for sustainable machining solutions will find Environment-Friendly Machining to be a useful volume.

Factors associated with utilization of traditional Chinese medicine by white collar foreign workers living in Taiwan

Science.gov (United States)

Daly, Maria; Tai, Chen-Jei; Deng, Chung-Yeh; Chien, Li-Yin

2009-01-01

Background Traditional Chinese medicine (TCM) has remained an integral part of Chinese culture and society for thousands of years. In Taiwan TCM is a recognized element of its National Health Insurance Scheme. However, there is no knowledge about how TCM is accessed by foreign workers from a non-Asian cultural background. The objectives of this study were to investigate the prevalence and patterns of TCM use among non-Asian white-collar workers living in Taiwan, and examine factors likely to influence their use of TCM. Methods This study applied a cross-sectional survey design. A total of 207 white-collar foreign workers of a non-Asian background currently holding National Health Insurance cards who had lived in Taiwan for 4 months or more participated in this study. Results The prevalence of TCM use was 45%. The most frequently used therapies were traditional Chinese herbs/medicine and acupuncture. Factors indicating the likelihood of TCM usage were age 31–40 years, visit to an allopathic medical doctor in the last year, ability to read Chinese, having a friend or family member available to assist in the use of TCM, and access to information about TCM services available in Taiwan. Conclusion Utilization of TCM by people of a non-Asian background living in Taiwan appears to be most influenced by enabling factors including language ability, access to information, and informal reference persons. PMID:19144152

A Swedish national twin study of criminal behavior and its violent, white-collar and property subtypes.

Science.gov (United States)

Kendler, K S; Maes, H H; Lönn, S L; Morris, N A; Lichtenstein, P; Sundquist, J; Sundquist, K

2015-08-01

We sought to clarify the etiological contribution of genetic and environmental factors to total criminal behavior (CB) measured as criminal convictions in men and women, and to violent (VCB), white-collar (WCCB) and property criminal behavior (PCB) in men only. In 21 603 twin pairs from the Swedish Twin Registry, we obtained information on all criminal convictions from 1973 to 2011 from the Swedish Crime Register. Twin modeling was performed using the OpenMx package. For all criminal convictions, heritability was estimated at around 45% in both sexes, with the shared environment accounting for 18% of the variance in liability in females and 27% in males. The correlation of these risk factors across sexes was estimated at +0.63. In men, the magnitudes of genetic and environmental influence were similar in the three criminal conviction subtypes. However, for violent and white-collar convictions, nearly half and one-third of the genetic effects were respectively unique to that criminal subtype. About half of the familial environmental effects were unique to property convictions. The familial aggregation of officially recorded CB is substantial and results from both genetic and familial environmental factors. These factors are moderately correlated across the sexes suggesting that some genetic and environmental influences on criminal convictions are unique to men and to women. Violent criminal behavior and property crime are substantially influenced respectively by genetic and shared environmental risk factors unique to that criminal subtype.

Factors associated with utilization of traditional Chinese medicine by white collar foreign workers living in Taiwan

Directory of Open Access Journals (Sweden)

Deng Chung-Yeh

2009-01-01

Full Text Available Abstract Background Traditional Chinese medicine (TCM has remained an integral part of Chinese culture and society for thousands of years. In Taiwan TCM is a recognized element of its National Health Insurance Scheme. However, there is no knowledge about how TCM is accessed by foreign workers from a non-Asian cultural background. The objectives of this study were to investigate the prevalence and patterns of TCM use among non-Asian white-collar workers living in Taiwan, and examine factors likely to influence their use of TCM. Methods This study applied a cross-sectional survey design. A total of 207 white-collar foreign workers of a non-Asian background currently holding National Health Insurance cards who had lived in Taiwan for 4 months or more participated in this study. Results The prevalence of TCM use was 45%. The most frequently used therapies were traditional Chinese herbs/medicine and acupuncture. Factors indicating the likelihood of TCM usage were age 31–40 years, visit to an allopathic medical doctor in the last year, ability to read Chinese, having a friend or family member available to assist in the use of TCM, and access to information about TCM services available in Taiwan. Conclusion Utilization of TCM by people of a non-Asian background living in Taiwan appears to be most influenced by enabling factors including language ability, access to information, and informal reference persons.

An addition to the diversity of dendrobatid frogs in Venezuela: description of three new collared frogs (Anura: Dendrobatidae: Mannophryne

Directory of Open Access Journals (Sweden)

César Luis Barrio-Amorós

2010-07-01

Full Text Available Three new species of collared frogs of the genus Mannophryne are described from Venezuela. Two are newly discovered taxa from the Venezuelan Andes, whereas the third species, previously confused with M. trinitatis, is from the Caracas area in the Cordillera de la Costa. The call of the three new species and that of Mannophryne collaris are described. Taxonomic, zoogeographic, and conservation issues are discussed.

Ductile and brittle transition behavior of titanium alloys in ultra-precision machining.

Science.gov (United States)

Yip, W S; To, S

2018-03-02

Titanium alloys are extensively applied in biomedical industries due to their excellent material properties. However, they are recognized as difficult to cut materials due to their low thermal conductivity, which induces a complexity to their deformation mechanisms and restricts precise productions. This paper presents a new observation about the removal regime of titanium alloys. The experimental results, including the chip formation, thrust force signal and surface profile, showed that there was a critical cutting distance to achieve better surface integrity of machined surface. The machined areas with better surface roughness were located before the clear transition point, defining as the ductile to brittle transition. The machined area at the brittle region displayed the fracture deformation which showed cracks on the surface edge. The relationship between depth of cut and the ductile to brittle transaction behavior of titanium alloys in ultra-precision machining(UPM) was also revealed in this study, it showed that the ductile to brittle transaction behavior of titanium alloys occurred mainly at relatively small depth of cut. The study firstly defines the ductile to brittle transition behavior of titanium alloys in UPM, contributing the information of ductile machining as an optimal machining condition for precise productions of titanium alloys.

Probing the Hypothesis of SAR Continuity Restoration by the Removal of Activity Cliffs Generators in QSAR.

Science.gov (United States)

Cruz-Monteagudo, Maykel; Medina-Franco, José L; Perera-Sardiña, Yunier; Borges, Fernanda; Tejera, Eduardo; Paz-Y-Miño, Cesar; Pérez-Castillo, Yunierkis; Sánchez-Rodríguez, Aminael; Contreras-Posada, Zuleidys; Cordeiro, M Natália D S

2016-01-01

In this work we report the first attempt to study the effect of activity cliffs over the generalization ability of machine learning (ML) based QSAR classifiers, using as study case a previously reported diverse and noisy dataset focused on drug induced liver injury (DILI) and more than 40 ML classification algorithms. Here, the hypothesis of structure-activity relationship (SAR) continuity restoration by activity cliffs removal is tested as a potential solution to overcome such limitation. Previously, a parallelism was established between activity cliffs generators (ACGs) and instances that should be misclassified (ISMs), a related concept from the field of machine learning. Based on this concept we comparatively studied the classification performance of multiple machine learning classifiers as well as the consensus classifier derived from predictive classifiers obtained from training sets including or excluding ACGs. The influence of the removal of ACGs from the training set over the virtual screening performance was also studied for the respective consensus classifiers algorithms. In general terms, the removal of the ACGs from the training process slightly decreased the overall accuracy of the ML classifiers and multi-classifiers, improving their sensitivity (the weakest feature of ML classifiers trained with ACGs) but decreasing their specificity. Although these results do not support a positive effect of the removal of ACGs over the classification performance of ML classifiers, the "balancing effect" of ACG removal demonstrated to positively influence the virtual screening performance of multi-classifiers based on valid base ML classifiers. Specially, the early recognition ability was significantly favored after ACGs removal. The results presented and discussed in this work represent the first step towards the application of a remedial solution to the activity cliffs problem in QSAR studies.

The Effect of Machining Conditions on the Forces in the Process of Roller Brush Machining

Directory of Open Access Journals (Sweden)

Jakub Matuszak

2017-12-01

Full Text Available Because of its advantages, brushing processing has many uses. The main ones include the removal of corrosion products, surface cleaning, deburring and shaping the properties of the surface layer. The intensity of these processes depends on the degree of impact of brush fibres on the work surface. In the case of tools, in which the resilient fibres are the working elements, forces in the brushing process, apart from the machining parameters, depend on the characteristics and overall dimensions of individual fibres. The paper presents the results of studies of the influence of technological parameters and type of fibres on the radial force in the brushing process.

Reagent precipitation of copper ions from wastewater of machine-building factories

Science.gov (United States)

Porozhnyuk, L. A.; Lupandina, N. S.; Porozhnyuk, E. V.

2018-03-01

The article presents the results of reagent removal of copper ions from wastewater of machine-building factories. The urgency of the study is conditioned by the widening of the range of effective reagents through the implementation of industrial waste. The investigation covers mineralogical and fractional composition of chalk enrichment waste. In the work, the conditions of thermal activation of chalk enrichment waste used for reagent removal of copper ions from wastewater were elaborated. It was shown that the thermal activation of waste facilitates the increased treatment efficacy up to the set sanitation, hygiene and technological standards.

Parametric optimization of ultrasonic machining process using gravitational search and fireworks algorithms

Directory of Open Access Journals (Sweden)

Debkalpa Goswami

2015-03-01

Full Text Available Ultrasonic machining (USM is a mechanical material removal process used to erode holes and cavities in hard or brittle workpieces by using shaped tools, high-frequency mechanical motion and an abrasive slurry. Unlike other non-traditional machining processes, such as laser beam and electrical discharge machining, USM process does not thermally damage the workpiece or introduce significant levels of residual stress, which is important for survival of materials in service. For having enhanced machining performance and better machined job characteristics, it is often required to determine the optimal control parameter settings of an USM process. The earlier mathematical approaches for parametric optimization of USM processes have mostly yielded near optimal or sub-optimal solutions. In this paper, two almost unexplored non-conventional optimization techniques, i.e. gravitational search algorithm (GSA and fireworks algorithm (FWA are applied for parametric optimization of USM processes. The optimization performance of these two algorithms is compared with that of other popular population-based algorithms, and the effects of their algorithm parameters on the derived optimal solutions and computational speed are also investigated. It is observed that FWA provides the best optimal results for the considered USM processes.

Pulse electrochemical meso/micro/nano ultraprecision machining technology.

Science.gov (United States)

Lee, Jeong Min; Kim, Young Bin; Park, Jeong Woo

2013-11-01

This study demonstrated meso/micro/nano-ultraprecision machining through electrochemical reactions using intermittent DC pulses. The experiment focused on two machining methods: (1) pulse electrochemical polishing (PECP) of stainless steel, and (2) pulse electrochemical nano-patterning (PECNP) on a silicon (Si) surface, using atomic force microscopy (AFM) for fabrication. The dissolution reaction at the stainless steel surface following PECP produced a very clean, smooth workpiece. The advantages of the PECP process included improvements in corrosion resistance, deburring of the sample surface, and removal of hydrogen from the stainless steel surface as verified by time-of-flight secondary-ion mass spectrometry (TOF-SIMS). In PECNP, the electrochemical reaction generated within water molecules produced nanoscale oxide textures on a Si surface. Scanning probe microscopy (SPM) was used to evaluate nanoscale-pattern processing on a Si wafer surface produced by AFM-PECNP For both processes using pulse electrochemical reactions, three-dimensional (3-D) measurements and AFM were used to investigate the changes on the machined surfaces. Preliminary results indicated the potential for advancing surface polishing techniques and localized micro/nano-texturing technology using PECP and PECNP processes.

Effects of shielding coatings on the anode shaping process during counter-rotating electrochemical machining

Science.gov (United States)

Wang, Dengyong; Zhu, Zengwei; Wang, Ningfeng; Zhu, Di

2016-09-01

Electrochemical machining (ECM) has been widely used in the aerospace, automotive, defense and medical industries for its many advantages over traditional machining methods. However, the machining accuracy in ECM is to a great extent limited by the stray corrosion of the unwanted material removal. Many attempts have been made to improve the ECM accuracy, such as the use of a pulse power, passivating electrolytes and auxiliary electrodes. However, they are sometimes insufficient for the reduction of the stray removal and have their limitations in many cases. To solve the stray corrosion problem in CRECM, insulating and conductive coatings are respectively used. The different implement processes of the two kinds of coatings are introduced. The effects of the two kinds of shielding coatings on the anode shaping process are investigated. Numerical simulations and experiments are conducted for the comparison of the two coatings. The simulation and experimental results show that both the two kinds of coatings are valid for the reduction of stray corrosion on the top surface of the convex structure. However, for insulating coating, the convex sidewall becomes concave when the height of the convex structure is over 1.26 mm. In addition, it is easy to peel off by the high-speed electrolyte. In contrast, the conductive coating has a strong adhesion, and can be well reserved during the whole machining process. The convex structure fabricated by using a conductive iron coating layer presents a favorable sidewall profile. It is concluded that the conductive coating is more effective for the improvement of the machining quality in CRECM. The proposed shielding coatings can also be employed to reduce the stray corrosion in other schemes of ECM.

A Mobile Robot for Emergency Operation of Fuel Exchange Machine

Energy Technology Data Exchange (ETDEWEB)

Seo, Yongchil; Lee, Sunguk; Kim, Changhoi; Shin, Hochul; Jung, Seungho; Choi, Changhwan [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2007-07-01

A Pressurized Heavy Water Reactor (PHWR) uses a heavy water as the coolant and moderator because it does not attenuate the neutron inside the reactor, which makes it possible to use natural uranium for nuclear fuels. However, since the uranium ratio is too low within the natural uranium, the reactor should be refueled everyday while the reactor is working. For that purpose, there is a fuel exchange machine. However as the time passes by, the durability and reliability become a problem. While the fuel handling machine exchanges the reactor fuel, it can be stuck to the pressure tube attached in the Calandra. Although this kind of situation is rarely happen, it can make the reactor be shutdown for normalizing the operation. Since the refueling is performed while the reactor is working, the radiation level is extremely high and the machine can be located at a high position up to nine meters from the floor, that is, the human worker can not approach the machine, so the fuel handling machine should be released remotely. To cope with this situation, the fuel handling machine has a manual drive mechanism at the rear side of it as shown in the circled images. If the worker can handle these manual drive mechanisms, the fuel handling machine can be released form the pressure tube. The KAERI had developed a long-reach manipulator system with a telescophic mast mechanism which can be deployed in the basement of the reactor room and manipulate the manual lever of the fuel exchange machine. Since the manipulator is located in the basement, there are several problems for its application such that the plug hole should be removed before the operation and the vibration of the mast mechanism make it difficult to locate the end effecter of the manipulator.

A Mobile Robot for Emergency Operation of Fuel Exchange Machine

International Nuclear Information System (INIS)

Seo, Yongchil; Lee, Sunguk; Kim, Changhoi; Shin, Hochul; Jung, Seungho; Choi, Changhwan

2007-01-01

A Pressurized Heavy Water Reactor (PHWR) uses a heavy water as the coolant and moderator because it does not attenuate the neutron inside the reactor, which makes it possible to use natural uranium for nuclear fuels. However, since the uranium ratio is too low within the natural uranium, the reactor should be refueled everyday while the reactor is working. For that purpose, there is a fuel exchange machine. However as the time passes by, the durability and reliability become a problem. While the fuel handling machine exchanges the reactor fuel, it can be stuck to the pressure tube attached in the Calandra. Although this kind of situation is rarely happen, it can make the reactor be shutdown for normalizing the operation. Since the refueling is performed while the reactor is working, the radiation level is extremely high and the machine can be located at a high position up to nine meters from the floor, that is, the human worker can not approach the machine, so the fuel handling machine should be released remotely. To cope with this situation, the fuel handling machine has a manual drive mechanism at the rear side of it as shown in the circled images. If the worker can handle these manual drive mechanisms, the fuel handling machine can be released form the pressure tube. The KAERI had developed a long-reach manipulator system with a telescophic mast mechanism which can be deployed in the basement of the reactor room and manipulate the manual lever of the fuel exchange machine. Since the manipulator is located in the basement, there are several problems for its application such that the plug hole should be removed before the operation and the vibration of the mast mechanism make it difficult to locate the end effecter of the manipulator

Residual magnetic field in rotary machines; Campo magnetico residual en maquinas rotatorias

Energy Technology Data Exchange (ETDEWEB)

Gonzalez V, Esteban A; Apanco R, Marcelino [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2007-07-01

The residual magnetism is a phenomenon in which the magnetic dipoles of a substance are oriented in a certain degree. On the other hand, when internal forces exist capable of aligning elementary magnetic dipoles of a material, a permanent magnet is obtained. Just as in a conductor or in a material, in the elements of a rotary electrical machine magnetic fields can be induced that produce a residual magnetism or magnetization. In the rotary electrical machines, the magnetization phenomenon causes serious problems, such as the generation of induced currents that propitiate the mechanical wear in bearings, collars, trunnions and inclusive in the shaft, by effects known as pitting, frosting and spark tracks, as well as erroneous readings in vibration and temperature sensors, that in some cases can cause the shut down of the machine. In this article are presented the general concepts on the residual magnetism in rotary electrical machines, the causes that originate it and the problems that arises, as well as the demagnetization of the components that have residual magnetic field. The results obtained by the area of Electrical Equipment of the Instituto de Investigaciones Electricas are revised, during the execution of activities related to the measurement and elimination of the residual magnetic field in rotary electrical machines. [Spanish] El magnetismo residual es un fenomeno en el que los dipolos magneticos de una sustancia se encuentran orientados en un grado determinado. Por otro lado, cuando existen fuerzas internas capaces de alinear los dipolos magneticos elementales de un material, se tiene un iman permanente. Al igual que en un conductor o un material, en los elementos de una maquina electrica rotatoria se pueden inducir campos magneticos que producen un magnetismo residual o magnetizacion. En las maquinas electricas rotatorias, el fenomeno de magnetizacion causa graves problemas, como la generacion de corrientes inducidas que propician el desgaste mecanico

Experience on sodium removal from various components

Energy Technology Data Exchange (ETDEWEB)

Kamei, M; Kanbe, M; Yagisawa, H; Sasaki, S; Kataoka, H; Fukada, T; Ishii, Y; Saito, R; Mimoto, Y [O-arai Engineering Centre, PNC, Ibaraki-ken, Tokio (Japan)

1978-08-01

Since 1970, OEC (O-arai Engineering Center) has been Investigating the following methods for removal of sodium from the components of sodium plants: steam cleaning for the 50 MW Steam Generator, secondary proto-type pump of 'JOYO' and Dummy fuel assembly of 'JOYO', alcohol cleaning for Sector Model of Intermediate Heat Exchanger (IHX) of 'JOYO', a sector model of Sodium-to-Air cooler of 'JOYO' and a proto-type isolation valve of 'JOYO' and cleaning by vacuumization at high temperature for Regenerative Heat Exchanger. This report describes the outline of the Sodium Disposal Facility and experience of sodium removal processing on the 50 MW Steam Generator, the crevices of the experimental sub-assemblies, the Fuel Handling Machine of 'MONJU' and the Regenerative Heat Exchanger of the Sodium Flow Test Facility. Through these experiences it was noted that, (1) Removal of sodium from crevices such as in bolted joints are very difficult. (2) Consideration is needed in the removal process where material damage might occur from the generation of hydro-oxides. (3) Some detection device to tell the completion of sodium removal as well as the end of reaction is required. (4) Requalification rules should be clarified. Efforts in this direction have been made in the case of a 'JOYO' prototype pump by reinstalling it after sodium removal five times. (author)

Experience on sodium removal from various components

International Nuclear Information System (INIS)

Kamei, M.; Kanbe, M.; Yagisawa, H.; Sasaki, S.; Kataoka, H.; Fukada, T.; Ishii, Y.; Saito, R.; Mimoto, Y.

1978-01-01

Since 1970, OEC (O-arai Engineering Center) has been Investigating the following methods for removal of sodium from the components of sodium plants: steam cleaning for the 50 MW Steam Generator, secondary proto-type pump of 'JOYO' and Dummy fuel assembly of 'JOYO', alcohol cleaning for Sector Model of Intermediate Heat Exchanger (IHX) of 'JOYO', a sector model of Sodium-to-Air cooler of 'JOYO' and a proto-type isolation valve of 'JOYO' and cleaning by vacuumization at high temperature for Regenerative Heat Exchanger. This report describes the outline of the Sodium Disposal Facility and experience of sodium removal processing on the 50 MW Steam Generator, the crevices of the experimental sub-assemblies, the Fuel Handling Machine of 'MONJU' and the Regenerative Heat Exchanger of the Sodium Flow Test Facility. Through these experiences it was noted that, (1) Removal of sodium from crevices such as in bolted joints are very difficult. (2) Consideration is needed in the removal process where material damage might occur from the generation of hydro-oxides. (3) Some detection device to tell the completion of sodium removal as well as the end of reaction is required. (4) Requalification rules should be clarified. Efforts in this direction have been made in the case of a 'JOYO' prototype pump by reinstalling it after sodium removal five times. (author)

Experience on sodium removal from various components

International Nuclear Information System (INIS)

Kamei, M.; Kanbe, M.; Yagisawa, H.; Sasaki, S.; Kataoka, H.

1978-02-01

Since 1970, OEC (O-arai Engineering Center) has been investigating the following methods for removal of sodium from the components of sodium plants: steam cleaning for the 50 MW Steam Generator, secondary proto-type pump of ''JOYO'' and Dummy fuel assembly of ''JOYO'', alcohol cleaning for Sector Model of Intermediate Heat Exchanger (IHX) of ''JOYO'', a sector model of Sodium-to-Air cooler of ''JOYO'' and a proto-type Isolation valve of ''JOYO'' and cleaning by vacuumization at high temperature for Regenerative Heat Exchanger. This report describes the outline of the Sodium Disposal Facility and experience of sodium removal processing on the 50 MW Steam Generator, the crevices of the experimental subassemblies, the Fuel Handling Machine of ''MONJU'' and the Regenerative Heat Exchanger of the Sodium Flow Test Facility. Through these experiences it was noted that, (1) Removal of Sodium from crevices such as in bolted joints are very difficult. (2) Consideration is needed in the removal process where material damage might occur from the generation of hydro-oxides. (3) Some detection device to tell the completion of sodium removal as well as the end of reaction is required. (4) Requalification rules should be clarified. Efforts in this direction have been made in the case of a ''JOYO'' prototype pump by reinstalling it after sodium removal five times. (author)

Nanosecond multi-pulse laser milling for certain area removal of metal coating on plastics surface

Science.gov (United States)

Zhao, Kai; Jia, Zhenyuan; Ma, Jianwei; Liu, Wei; Wang, Ling

2014-12-01

Metal coating with functional pattern on engineering plastics surface plays an important role in industry applications; it can be obtained by adding or removing certain area of metal coating on engineering plastics surface. However, the manufacturing requirements are improved continuously and the plastic substrate presents three-dimensional (3D) structure-many of these parts cannot be fabricated by conventional processing methods, and a new manufacturing method is urgently needed. As the laser-processing technology has many advantages like high machining accuracy and constraints free substrate structure, the machining of the parts is studied through removing certain area of metal coating based on the nanosecond multi-pulse laser milling. To improve the edge quality of the functional pattern, generation mechanism and corresponding avoidance strategy of the processing defects are studied. Additionally, a prediction model for the laser ablation depth is proposed, which can effectively avoid the existence of residual metal coating and reduces the damage of substrate. With the optimal machining parameters, an equiangular spiral pattern on copper-clad polyimide (CCPI) is machined based on the laser milling at last. The experimental results indicate that the edge of the pattern is smooth and consistent, the substrate is flat and without damage. The achievements in this study could be applied in industrial production.

Effect of heat treatments on machinability of gold alloy with age-hardenability at intraoral temperature.

Science.gov (United States)

Watanabe, I; Baba, N; Watanabe, E; Atsuta, M; Okabe, T

2004-01-01

This study investigated the effect of heat treatment on the machinability of heat-treated cast gold alloy with age-hardenability at intraoral temperature using a handpiece engine with SiC wheels and an air-turbine handpiece with carbide burs and diamond points. Cast gold alloy specimens underwent various heat treatments [As-cast (AC); Solution treatment (ST); High-temperature aging (HA), Intraoral aging (IA)] before machinability testing. The machinability test was conducted at a constant machining force of 0.784N. The three circumferential speeds used for the handpiece engine were 500, 1,000 and 1,500 m/min. The machinability index (M-index) was determined as the amount of metal removed by machining (volume loss, mm(3)). The results were analyzed by ANOVA and Scheffé's test. When an air-turbine handpiece was used, there was no difference in the M-index of the gold alloy among the heat treatments. The air-turbine carbide burs showed significantly (pmachinability of the gold alloy using the air-turbine handpiece. The heat treatments had a small effect on the M-index of the gold alloy machined with a SiC wheel for a handpiece engine.

Machinability and Tribological Properties of Stir Cast LM6/SiC/GR Hybrid Metal Matrix Composite

Directory of Open Access Journals (Sweden)

Tahat Montasser S.

2016-01-01

Full Text Available Analysis on machining characteristics in turning of LM6/SiC/Gr hybrid metal matrix composites is made of (Al-11.8%Si/SiC/Gr hybrid metal matrix composites. The process performances such as porosity, wear rate of the composites, tool wear, tool life, specific modulus, surface roughness and material removal rate with equal weight fraction of SiC and Gr particulates of 3%, 7%, 10% and 13% reinforcement are investigated. This experimental analysis and test results on the machinability of Al/SiCMMC will provide essential guidelines to the manufacturers. Hybird metal matrix composites reinforced with graphite particles posses better machinability and tribological properties.

Coyote removal, understory cover, and survival of white-tailed deer neonates: Coyote Control and Fawn Survival

Energy Technology Data Exchange (ETDEWEB)

Kilgo, John C. [USDA Forest Service; Southern Research Station, New Ellenton, SC (United States); Vukovich, Mark [USDA Forest Service; Southern Research Station, New Ellenton, SC (United States); Ray, H. Scott [USDA Forest Service, Savannah River; New Ellenton, SC (United States); Shaw, Christopher E. [USDA Forest Service; Southern Research Station, New Ellenton, SC (United States); Ruth, Charles [South Carolina Dept. of Natural Resources, Columbia, SC (United States)

2014-09-01

Predation by coyotes (Canis latrans) on white-tailed deer (Odocoileus virginianus) neonates has led to reduced recruitment in many deer populations in southeastern North America. This low recruitment combined with liberal antlerless deer harvest has resulted in declines in some deer populations, and consequently, increased interest in coyote population control. We investigated whether neonate survival increased after coyote removal, whether coyote predation on neonates was additive to other mortality sources, and whether understory vegetation density affected neonate survival. We monitored neonate survival for 4 years prior to (2006–2009) and 3 years during (2010–2012) intensive coyote removal on 3 32-km² units on the United States Department of Energy’s Savannah River Site, South Carolina. We removed 474 coyotes (1.63 coyotes/km² per unit per year), reducing coyote abundance by 78% from pre-removal levels. The best model (w_i = 0.927) describing survival probability among 216 radio-collared neonates included a within-year quadratic time trend variable, date of birth, removal treatment, and a varying removal year effect. Under this model, survival differed between pre-treatment and removal periods and it differed among years during the removal period, being >100% greater than pre-treatment survival (0.228) during the first removal year (0.513), similar to pre-treatment survival during the second removal year (0.202), and intermediate during the third removal year (0.431). Despite an initial increase, the overall effect of coyote removal on neonate survival was modest. Mortality rate attributable to coyote predation was lowest during the first removal year (0.357) when survival was greatest, but the mortality rate from all other causes did not differ between the pretreatment period and any year during removals, indicating that coyote predation acted as an additive source of mortality. Survival probability was not related to

Response surface modelling of tool electrode wear rate and material removal rate in micro electrical discharge machining of Inconel 718

DEFF Research Database (Denmark)

Puthumana, Govindan

2017-01-01

conductivity and high strength causing it extremely difficult tomachine. Micro-Electrical Discharge Machining (Micro-EDM) is a non-conventional method that has a potential toovercome these restrictions for machining of Inconel 718. Response Surface Method (RSM) was used for modelling thetool Electrode Wear...

WHITE-COLLAR CRIME’S FORECASTING AND REDUCTION BY MEANS OF PRE-EMPLOYMENT TESTING IN THE PENAL POLITICS OF THE STATE: EMPIRICAL FINDINGS FOR MOLDOVA AND ISRAEL

Directory of Open Access Journals (Sweden)

Jacob RUB

2017-01-01

Full Text Available The purpose of the present article is to elaborate a valid method of forecasting of the potential offender during the hiring process by means of pre-employment tests as an integral part of the process of prevention and counteracting of the phenomenon of white-collar criminality in the realm of Penal Politics of the Republic of Moldova and the State of Israel. Namely, the „personality coefficient” of the potential offender, which, in the author’s opinion, will define better the likelihood of success in perpetrating a white-collar crime. As a result, a new methodology and tactics for the earlier reducing of white-collar criminality at workplace a new and original scale of pre-employment test valid for hiring process which will be justifiable not only from economical and sociological standpoint, but also from criminological point of view in the process of white-collar criminality reducing.Prognozarea şi reducerea criminalităţii gulerelor albe prin metoda testărilor pre-angajatoare în politica penală a statului: rezultatele empirice pentru Moldova şi IsraelScopul propus în acest articol constă în elaborarea unei metode valide pentru identificarea criminalilor potenţiali în procesul de angajare prin teste de pre-selecţie privite ca parte integrantă a procesului de prevenire şi combatere a fenomenului criminalităţii gulerelor albe în cadrul politicii penale a Republicii Moldova şi a Statului Israel. În special, este propus spre utilizare „coeficientul personalităţii” potenţialului infractor care, în opinia autorului, va defini mai precis probabilitatea săvârşirii crimei gulerelor albe. Prin urmare, este propusă şi argumentată o nouă metodologie şi tactică de reducere a criminalităţii gulerelor albe la locul de muncă, precum şi un model original de testare pre-angajare oportun din perspectivă economică, sociologică şi criminologică.

Zero waste machine coolant management strategy at Los Alamos National Laboratory

International Nuclear Information System (INIS)

Carlson, B.; Algarra, F.; Wilburn, D.

1998-01-01

Machine coolants are used in machining equipment including lathes, grinders, saws and drills. The purpose of coolants is to wash away machinery debris in the form of metal fines, lubricate, and disperse heat between the part and the machine tool. An effective coolant prolongs tool life and protects against part rejection, commonly due to scoring or scorching. Traditionally, coolants have a very short effective life in the machine, often times being disposed of as frequently as once per week. The cause of coolant degradation is primarily due to the effects of bacteria, which thrive in the organic rich coolant environment. Bacteria in this environment reproduce at a logarithmic rate, destroying the coolant desirable aspects and causing potential worker health risks associated with the use of biocides to control the bacteria. The strategy described in this paper has effectively controlled bacterial activity without the use of biocides, avoided disposal of a hazardous waste, and has extended coolant life indefinitely. The Machine Coolant Management Strategy employed a combination of filtration, heavy lubricating oil removal, and aeration, which maintained the coolant peak performance without the use of biocides. In FY96, the Laboratory generated and disposed of 19,880 kg of coolants from 9 separate sites at a cost of $145K. The single largest generator was the main machine shop producing an average 14,000 kg annually. However, in FY97, the waste generation for the main machine shop dropped to 4,000 kg after the implementation of the zero waste strategy. It is expected that this value will be further reduced in FY98

Employing Ti nano-powder dielectric to enhance surface characteristics in electrical discharge machining of AISI D2 steel

Energy Technology Data Exchange (ETDEWEB)

Marashi, Houriyeh, E-mail: houriyeh@marashi.co [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia); Sarhan, Ahmed A.D., E-mail: ah_sarhan@yahoo.com [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia); Department of Mechanical Engineering, Faculty of Engineering, Assiut University, Assiut 71516 (Egypt); Hamdi, Mohd [Department of Mechanical Engineering, Faculty of Engineering, University of Malaya, 50603 Kuala Lumpur (Malaysia); Center of Advanced Manufacturing and Materials Processing (AMMP), 50603 Kuala Lumpur (Malaysia)

2015-12-01

Graphical abstract: - Highlights: • We proposed adding Ti nano-powder to dielectric in EDM. • Average and peak-valley surface roughness was improved by 35 and 40%, respectively. • Improvement of up to 69% in material removal rate was obtained. • Enhanced surface morphology and formation of shallower craters were observed. - Abstract: Manufacturing components with superior surface characteristics is challenging when electrical discharge machining (EDM) is employed for mass production. The aim of this research is to enhance the characteristics of AISI D2 steel surface machined with EDM through adding Ti nano-powder to dielectric under various machining parameters, including discharge duration (T{sub on}) and peak current (I). Surface roughness profilometer, FESEM and AFM analysis were utilized to reveal the machined surface characteristics in terms of surface roughness, surface morphology and surface micro-defects. Moreover, EDX analysis was performed in order to evaluate the atomic deposition of Ti nano-powder on the surface. The concentration of Ti nano-powder in dielectric was also examined using ESEM and EDX. According to the results, the addition of Ti nano-powder to dielectric notably enhanced the surface morphology and surface roughness at all machining parameters except T{sub on} = 340 μs. Of these parameters, maximum enhancement was observed at T{sub on} = 210 μs, where the material removal rate and average surface roughness improved by ∼69 and ∼35% for peak current of 6 and 12 A, respectively. Elemental analysis signified negligible Ti deposition on the machined surface while the atomic concentration of Ti was increased around the crack areas.

Job mismatching, unequal opportunities and long-term sickness absence in female white-collar workers in Sweden.

Science.gov (United States)

Sandmark, Hélène

2009-01-01

To investigate associations between long-term sick-listing and factors at work and in family life. Associations were investigated in a cross-sectional case-referent study. The study base included women in white-collar jobs, aged 30-55 years, living in three urban areas in Sweden between February 2004 and October 2004. A postal questionnaire was constructed with questions on occupational and family circumstances, and sent to 513 randomly selected female white-collar workers, of whom 233 had ongoing sick-leave of 90 days or more. The response rate was 81% (n = 413). Most of the women in this study were in managerial positions. The unadjusted associations showed that sick-listed women with children showed the highest estimates regarding reported long working hours, bullying, high mental strain, low control and low influence at work, and work-family imbalance. In a regression model, the strongest associations were: experiencing too high mental strain in work tasks (odds ratio (OR) = 2.57, 95% confidence interval (CI) = 2.09-3.15) and low control and influence at work (OR=2.17, 95% CI= 1.60-2.94). Sick-listed women reported an overall higher dissatisfaction with their workplace and working life. There seems to be a greater tendency for the sick-listed women in this study to experience low control and too high mental strain at work and to live in traditional family relationships with unequal opportunities. The women who were sick-listed were probably less able to cope with work stress and to find a balance between work and family life.

Machine terms dictionary

Energy Technology Data Exchange (ETDEWEB)

NONE

1979-04-15

This book gives descriptions of machine terms which includes machine design, drawing, the method of machine, machine tools, machine materials, automobile, measuring and controlling, electricity, basic of electron, information technology, quality assurance, Auto CAD and FA terms and important formula of mechanical engineering.

TEA CO2 laser machining of CFRP composite

Science.gov (United States)

Salama, A.; Li, L.; Mativenga, P.; Whitehead, D.

2016-05-01

Carbon fibre-reinforced polymer (CFRP) composites have found wide applications in the aerospace, marine, sports and automotive industries owing to their lightweight and acceptable mechanical properties compared to the commonly used metallic materials. Machining of CFRP composites using lasers can be challenging due to inhomogeneity in the material properties and structures, which can lead to thermal damages during laser processing. In the previous studies, Nd:YAG, diode-pumped solid-state, CO2 (continuous wave), disc and fibre lasers were used in cutting CFRP composites and the control of damages such as the size of heat-affected zones (HAZs) remains a challenge. In this paper, a short-pulsed (8 μs) transversely excited atmospheric pressure CO2 laser was used, for the first time, to machine CFRP composites. The laser has high peak powers (up to 250 kW) and excellent absorption by both the carbon fibre and the epoxy binder. Design of experiment and statistical modelling, based on response surface methodology, was used to understand the interactions between the process parameters such as laser fluence, repetition rate and cutting speed and their effects on the cut quality characteristics including size of HAZ, machining depth and material removal rate (MRR). Based on this study, process parameter optimization was carried out to minimize the HAZ and maximize the MRR. A discussion is given on the potential applications and comparisons to other lasers in machining CFRP.

Evaluating the electrical discharge machining (EDM) parameters with using carbon nanotubes

Science.gov (United States)

Sari, M. M.; Noordin, M. Y.; Brusa, E.

2012-09-01

Electrical discharge machining (EDM) is one of the most accurate non traditional manufacturing processes available for creating tiny apertures, complex or simple shapes and geometries within parts and assemblies. Performance of the EDM process is usually evaluated in terms of surface roughness, existence of cracks, voids and recast layer on the surface of product, after machining. Unfortunately, the high heat generated on the electrically discharged material during the EDM process decreases the quality of products. Carbon nanotubes display unexpected strength and unique electrical and thermal properties. Multi-wall carbon nanotubes are therefore on purpose added to the dielectric used in the EDM process to improve its performance when machining the AISI H13 tool steel, by means of copper electrodes. Some EDM parameters such as material removal rate, electrode wear rate, surface roughness and recast layer are here first evaluated, then compared to the outcome of EDM performed without using nanotubes mixed to the dielectric. Independent variables investigated are pulse on time, peak current and interval time. Experimental evidences show that EDM process operated by mixing multi-wall carbon nanotubes within the dielectric looks more efficient, particularly if machining parameters are set at low pulse of energy.

Evaluating the electrical discharge machining (EDM) parameters with using carbon nanotubes

International Nuclear Information System (INIS)

Sari, M M; Brusa, E; Noordin, M Y

2012-01-01

Electrical discharge machining (EDM) is one of the most accurate non traditional manufacturing processes available for creating tiny apertures, complex or simple shapes and geometries within parts and assemblies. Performance of the EDM process is usually evaluated in terms of surface roughness, existence of cracks, voids and recast layer on the surface of product, after machining. Unfortunately, the high heat generated on the electrically discharged material during the EDM process decreases the quality of products. Carbon nanotubes display unexpected strength and unique electrical and thermal properties. Multi-wall carbon nanotubes are therefore on purpose added to the dielectric used in the EDM process to improve its performance when machining the AISI H13 tool steel, by means of copper electrodes. Some EDM parameters such as material removal rate, electrode wear rate, surface roughness and recast layer are here first evaluated, then compared to the outcome of EDM performed without using nanotubes mixed to the dielectric. Independent variables investigated are pulse on time, peak current and interval time. Experimental evidences show that EDM process operated by mixing multi-wall carbon nanotubes within the dielectric looks more efficient, particularly if machining parameters are set at low pulse of energy.

A single-item global job satisfaction measure is associated with quantitative blood immune indices in white-collar employees.

Science.gov (United States)

Nakata, Akinori; Irie, Masahiro; Takahashi, Masaya

2013-01-01

Although a single-item job satisfaction measure has been shown to be reliable and inclusive as multiple-item scales in relation to health, studies including immunological data are few. The purpose of this study was to evaluate the validity of single-item job and family life satisfaction based on its association with immune indices. A total of 189 white-collar employees (70% men) underwent a blood draw for the measurement of natural killer (NK), total T, and B cell counts as well as plasma immunoglobulin (Ig) G concentrations and completed single-item job and family life satisfaction measures, respectively. The response options for satisfaction measures were 'dissatisfied' (coded 1) to 'satisfied' (coded 4). Spearman's partial correlations controlling for cofactors revealed that increased job satisfaction was positively associated with NK cells (rsp=0.201, p=0.007) and IgG (rsp=0.178, p=0.018), while family life satisfaction was unrelated to immune indices. Those who reported a combination of low job/low family life satisfaction had significantly lower NK and higher B cell counts than those with a high job/high family life satisfaction. Our study suggests that the single-item summary measure of job satisfaction, but not family life satisfaction, may be a valid tool to evaluate immune status in healthy white-collar employees.

Oral impacts on daily performances in white-collar port workers in Nellore, India - a cross-sectional study.

Science.gov (United States)

Soundarya Chowdary, Mandava; Sudhir, Kudlur Maheswarappa; Reddy, Vuyurru Chandrasekhara; Krishna Kumar, Rachakorda Veera Venkata Sathya Sai; Srinivasulu, Gomasani

2016-01-01

Oral diseases not only cause pain, but severely impair large number of individuals and can affect various aspects of life, including oral functions, appearance and interpersonal relationships. The aim of the study was to assess the interrelationship between oral impact on daily performance (OIDP) scores, socio-demographic characteristics, dental caries experience and periodontal status. A cross-sectional descriptive epidemiological study was conducted on a sample of 250 white-collar port workers who were willing to participate. OIDP was assessed using pre-validated questionnaire. Oral health status was assessed using modified World Health Organisation (1997) Proforma. Test of association was conducted between the OIDP score, socio-demographic variables, and periodontal status; loss of attachment was determined by using chi-square statistics and Mann-Whitney test. Logistic regression was performed to identify significant predictors of OIDP scores by inputting clinical oral examination variables into the equation, stepwise. A total of 250 white-collar workers in the port participated in the study with mean age of 34.67 ± 6.36. Among them, 219 were males and 31 were females. The OIDP items most commonly affected by oral health status were eating and enjoying food (48.4%), cleaning teeth (48%), sleeping and relaxing (44.4%).There was statistically significant relationship between missing teeth in the decayed missing filled teeth component and OIDP score (p workers in the port. Physical functions of teeth like eating and cleaning of teeth, sleeping and relaxing were more affected.

Effect of surface machining on corrosion behavior of SA182-304 in simulated

International Nuclear Information System (INIS)

Zhang Zhiming; Wang Jianqiu; Han Enhou; Ke Wei

2015-01-01

Different machining processes of mechanical parts can cause surface damage layers with different levels. The surface deformed layer can affect the corrosion behavior and service life of these mechanical parts a lot during the following service process. As a result, it is a key issue for the fabrication of the mechanical parts with long life that the selection of proper machining parameters and the removal of surface damage. The purpose of this study is to study the influence of different turning parameters on the corrosion behavior of nuclear grade SA182-304 stainless steel widely used in the advanced pressured water reactors (PWRs). 6 kinds of samples with different surface state are prepared by a lathe with different machining parameters, such as the feed, cutting speed and back engagement of the cutting edge. The high temperature and high pressure immersion test of these samples in the simulated PWR primary watershows that machining processes can affect the microstructure and chemical composition of the formed surface oxide scales a lot. According to the experimental results, the proper machining parameters for the studied SA182-304 are suggested. (authors)

Some relations between quantum Turing machines and Turing machines

OpenAIRE

Sicard, Andrés; Vélez, Mario

1999-01-01

For quantum Turing machines we present three elements: Its components, its time evolution operator and its local transition function. The components are related with the components of deterministic Turing machines, the time evolution operator is related with the evolution of reversible Turing machines and the local transition function is related with the transition function of probabilistic and reversible Turing machines.

Machinability of magnesium and aluminium alloys. Part I: cutting resistance

International Nuclear Information System (INIS)

Balout, B.; Songmene, V.; Masounave, J.

2002-01-01

Aluminium (2.7 g/cm 3 ) and magnesium (1.7 g/cm 3 ) are two competing light metals with similar mechanical properties and excellent possibilities for recycling. The forming of magnesium is often seen as an impediment to its use. New forming techniques using magnesium shavings are being developed, particularly in Japan. The machining of magnesium alloys by removal of metal raises safety concerns (risk of fire), which limits many potential applications of magnesium. The purpose of this work is to clarify and compare the machining properties of these two types of metal and better understand the mechanisms that may explain the differences in behaviour. Such a comparison could eventually provide an estimate of the cost of producing shavings for the manufacture of aluminium and magnesium parts through forging and extrusion, which would limit environmental pollution. Based on an analysis of cutting resistance during machining, it was demonstrated that magnesium alloys are easier to machine than similar aluminium alloys. Magnesium shavings are shorter than those of 6061-T6, but are especially more regular than those of A356, and their size is independent of cutting speed. It was also demonstrated that the fragility of materials can be characterized based on the results of cutting resistance produced during drilling

Machining of the nuclear tube sheet with small hole diameter

International Nuclear Information System (INIS)

Lin Lifeng

2010-01-01

Regarding the tube sheet for the heat exchanger of Qinshan Phase II extension project, its material is 00Cr19Ni10 forgings, the tube sheet thickness is 125 mm, requiring 178-φ10.35 0 +0.05 hole, the tube array shall take the shape of equilateral triangle, the center distance is 15 mm, and the tube hole roughness is Ra 3.2. The guide sleeve shall be adopted for positioning prior to machining of the high precision small hole of the thick tube sheet, and the gun drill and BTA drill shall be adopted for testing, finally BTA drilling with internal chip removal shall be adopted, this method shall overcome the disadvantage factor of BTA drilling and shall be the new approach for drilling. The diameter of BTA drill is φ10.34 mm. The machined hole diameter shall be φ10.375-φ10.355 mm. The ellipticity of the tube hole shall be less than 0.01 mm, the pipe bridge dimension shall be 4.6 mm, conforming to the requirement of the drawing. The paper presents the precautions during machining so as to provide the reference for the similar pipe hole machining in the future. (author)

Proposal for the award of a contract for the supply of austenitic steel strips for collars of the LHC superconducting dipole magnets

CERN Document Server

1999-01-01

This document concerns the award of a contract for the supply of 410 mm-wide austenitic steel strips for the collars of the LHC superconducting dipole magnets. Following a market survey carried out among 39 firms in twelve Member States and two firms in Japan, a call for tenders (IT-2618/LHC/LHC) was sent on 3 June 1999 to five firms in four Member States and two firms in Japan. The Council agreed to the Management?s proposal to invite Japanese industry to participate, where appropriate, in calls for tenders for supplies for the LHC Project (CERN/CC/2110). By the closing date, CERN had received six tenders. The Finance Committee is invited to approve the negotiation of a contract with the firm NIPPON STEEL CORPORATION (JP) for the supply of 11 000 tonnes of 410 mm-wide austenitic steel strips for the collars of the LHC superconducting dipole magnets for a total amount of 4 298 943 000 Japanese yen, subject to revision for contractual deliveries after 31 December 2000, with an option for the supply of up to 10...

Support vector machine in machine condition monitoring and fault diagnosis

Science.gov (United States)

Widodo, Achmad; Yang, Bo-Suk

2007-08-01

Recently, the issue of machine condition monitoring and fault diagnosis as a part of maintenance system became global due to the potential advantages to be gained from reduced maintenance costs, improved productivity and increased machine availability. This paper presents a survey of machine condition monitoring and fault diagnosis using support vector machine (SVM). It attempts to summarize and review the recent research and developments of SVM in machine condition monitoring and diagnosis. Numerous methods have been developed based on intelligent systems such as artificial neural network, fuzzy expert system, condition-based reasoning, random forest, etc. However, the use of SVM for machine condition monitoring and fault diagnosis is still rare. SVM has excellent performance in generalization so it can produce high accuracy in classification for machine condition monitoring and diagnosis. Until 2006, the use of SVM in machine condition monitoring and fault diagnosis is tending to develop towards expertise orientation and problem-oriented domain. Finally, the ability to continually change and obtain a novel idea for machine condition monitoring and fault diagnosis using SVM will be future works.

New human machine interface for VR-1 training reactor

International Nuclear Information System (INIS)

Kropik, M.; Matejka, K.; Sklenka, L.; Chab, V.

2002-01-01

The contribution describes a new human machine interface that was installed at the VR-1 training reactor. The human machine interface update was completed in the summer 2001. The human machine interface enables to operate the training reactor. The interface was designed with respect to functional, ergonomic and aesthetic requirements. The interface is based on a personal computer equipped with two displays. One display enables alphanumeric communication between a reactor operator and the control and safety system of the nuclear reactor. Messages appear from the control system, the operator can write commands and send them there. The second display is a graphical one. It is possible to represent there the status of the reactor, principle parameters (as power, period), control rods' positions, the course of the reactor power. Furthermore, it is possible to set parameters, to show the active core configuration, to perform reactivity calculations, etc. The software for the new human machine interface was produced in the InTouch developing environment of the WonderWare Company. It is possible to switch the language of the interface between Czech and English because of many foreign students and visitors at the reactor. The former operator's desk was completely removed and superseded with a new one. Besides of the computer and the two displays, there are control buttons, indicators and individual numerical displays of instrumentation there. Utilised components guarantee high quality of the new equipment. Microcomputer based communication units with proper software were developed to connect the contemporary control and safety system with the personal computer of the human machine interface and the individual displays. New human machine interface at the VR-1 training reactor improves the safety and comfort of the reactor utilisation, facilitates experiments and training, and provides better support of foreign visitors.(author)

Automatic microseismic event picking via unsupervised machine learning

Science.gov (United States)

Chen, Yangkang

2018-01-01

Effective and efficient arrival picking plays an important role in microseismic and earthquake data processing and imaging. Widely used short-term-average long-term-average ratio (STA/LTA) based arrival picking algorithms suffer from the sensitivity to moderate-to-strong random ambient noise. To make the state-of-the-art arrival picking approaches effective, microseismic data need to be first pre-processed, for example, removing sufficient amount of noise, and second analysed by arrival pickers. To conquer the noise issue in arrival picking for weak microseismic or earthquake event, I leverage the machine learning techniques to help recognizing seismic waveforms in microseismic or earthquake data. Because of the dependency of supervised machine learning algorithm on large volume of well-designed training data, I utilize an unsupervised machine learning algorithm to help cluster the time samples into two groups, that is, waveform points and non-waveform points. The fuzzy clustering algorithm has been demonstrated to be effective for such purpose. A group of synthetic, real microseismic and earthquake data sets with different levels of complexity show that the proposed method is much more robust than the state-of-the-art STA/LTA method in picking microseismic events, even in the case of moderately strong background noise.

Multi criteria decision making of machining parameters for Die Sinking EDM Process

Directory of Open Access Journals (Sweden)

G. K. Bose

2015-04-01

Full Text Available Electrical Discharge Machining (EDM is one of the most basic non-conventional machining processes for production of complex geometries and process of hard materials, which are difficult to machine by conventional process. It is capable of machining geometrically complex or hard material components, that are precise and difficult-to-machine such as heat-treated tool steels, composites, super alloys, ceramics, carbides, heat resistant steels etc. The present study is focusing on the die sinking electric discharge machining (EDM of AISI H 13, W.-Nr. 1.2344 Grade: Ovar Supreme for finding out the effect of machining parameters such as discharge current (GI, pulse on time (POT, pulse off time (POF and spark gap (SG on performance response like Material removal rate (MRR, Surface Roughness (Ra & Overcut (OC using Square-shaped Cu tool with Lateral flushing. A well-designed experimental scheme is used to reduce the total number of experiments. Parts of the experiment are conducted with the L9 orthogonal array based on the Taguchi methodology and significant process parameters are identified using Analysis of Variance (ANOVA. It is found that MRR is affected by gap current & Ra is affected by pulse on time. Moreover, the signal-to-noise ratios associated with the observed values in the experiments are determined by which factor is most affected by the responses of MRR, Ra and OC. These experimental data are further investigated using Grey Relational Analysis to optimize multiple performances in which different levels combination of the factors are ranked based on grey relational grade. The analysis reveals that substantial improvement in machining performance takes place following this technique.

Simulations of Quantum Turing Machines by Quantum Multi-Stack Machines

OpenAIRE

Qiu, Daowen

2005-01-01

As was well known, in classical computation, Turing machines, circuits, multi-stack machines, and multi-counter machines are equivalent, that is, they can simulate each other in polynomial time. In quantum computation, Yao [11] first proved that for any quantum Turing machines $M$, there exists quantum Boolean circuit $(n,t)$-simulating $M$, where $n$ denotes the length of input strings, and $t$ is the number of move steps before machine stopping. However, the simulations of quantum Turing ma...

Malaria-infected female collared flycatchers (Ficedula albicollis do not pay the cost of late breeding.

Directory of Open Access Journals (Sweden)

Katarzyna Kulma

Full Text Available Life-history theory predicts that the trade-off between parasite defense and other costly traits such as reproduction may be most evident when resources are scarce. The strength of selection that parasites inflict on their host may therefore vary across environmental conditions. Collared flycatchers (Ficedula albicollis breeding on the Swedish island Öland experience a seasonal decline in their preferred food resource, which opens the possibility to test the strength of life-history trade-offs across environmental conditions. We used nested-PCR and quantitative-PCR protocols to investigate the association of Haemosporidia infection with reproductive performance of collared flycatcher females in relation to a seasonal change in the external environment. We show that despite no difference in mean onset of breeding, infected females produced relatively more of their fledglings late in the season. This pattern was also upheld when considering only the most common malaria lineage (hPHSIB1, however there was no apparent link between the reproductive output and the intensity of infection. Infected females produced heavier-than-average fledglings with higher-than-expected recruitment success late in the season. This reversal of the typical seasonal trend in reproductive output compensated them for lower fledging and recruitment rates compared to uninfected birds earlier in the season. Thus, despite different seasonal patterns of reproductive performance the overall number of recruits was the same for infected versus uninfected birds. A possible explanation for our results is that infected females breed in a different microhabitat where food availability is higher late in the season but also is the risk of infection. Thus, our results suggest that another trade-off than the one we aimed to test is more important for explaining variation in reproductive performance in this natural population: female flycatchers appear to face a trade-off between the risk

Connection of control circuits of machine for automatic measurement of radioactive samples

International Nuclear Information System (INIS)

Vorlicek, J.

1984-01-01

A windowless through-flow gas detector is used for measurement. The automatic machine is controlled by four flip-flops defining the following states: the dish replacement in the measuring space, washing, measurement, measured value print-out, and resetting. The first and second outputs of the first, second and third flip-flops are connected to six inputs of a block whose four outputs provide counter reset and stop-watch reset, washing, measurement, and print-out. Such machine control eliminates measurement errors by disabling sample measurement until air is removed from the measurement space, introduced on an unwashed dish or on several dishes passed under the detector. The elimination of this error is also guaranteed in manual operation. (M.D.)

Machine tool structures

CERN Document Server

Koenigsberger, F

1970-01-01

Machine Tool Structures, Volume 1 deals with fundamental theories and calculation methods for machine tool structures. Experimental investigations into stiffness are discussed, along with the application of the results to the design of machine tool structures. Topics covered range from static and dynamic stiffness to chatter in metal cutting, stability in machine tools, and deformations of machine tool structures. This volume is divided into three sections and opens with a discussion on stiffness specifications and the effect of stiffness on the behavior of the machine under forced vibration c

Handbook on Air Cleaning Particulate Removal

Science.gov (United States)

1952-09-01

Type D Rotoclone, another type of (Fig. 2.7) has an exit duct fitted with an centrifugal dust separator (Fig. 2.8), in- adjustable collar which controls ...8091 10,870 15,056 18.620 Cost/sq ft cloth area 3.26 4.80 1.80 2.42 1.68 2.08 aIntermittent operation bAutomatic -continuous operation hh PERFORMANCE

An experimental and analytical investigation into the effects of process vibrations on material removal rates during polishing

Science.gov (United States)

Mullany, B.; Mainuddin, M.; Williams, W.; Keanini, R.

2013-06-01

Experimental testing, using both commercially available polishing machines and a specially built test platform, demonstrates that material removal rates (MRRs) observed during polishing of fused silica are strongly affected by nanometer-scale vibration amplitudes. Specifically, a nanometer level increase in system vibrations can produce MRRs approximately 150% higher than on an inherently smoother running machine. Moreover the higher spatial frequency surface roughness values are little-effected by the spectral content of the polishing machine. Polishing under controlled conditions, using the test platform, shows that for vibration amplitudes, A ≲ 1.6 μm, and over a fairly wide range of vibration frequencies, MRR increases almost linearly with increasing input power. By contrast, for A ≳ 10 μm, MRR exhibits a rapid decay with increasing A. Order of magnitude analyses and physical arguments are presented in order to explain the qualitatively distinct MRR trends observed. In the small-amplitude limit, A ≲ 1.6 μm, two arguments are presented which suggest that the total observed removal rate, MRRtot, reflects the superposed action of chemical-mechanical removal, MRRcm, and vibration-driven, flow-induced removal, MRRflow, i.e., MRRtot=MRRcm+MRRflow. The analyses further indicate that MRRflow primarily reflects cyclic viscous shears and pressure gradients extant within the thin, non-Newtonian slurry film that exists between the polishing tool and workpiece. Shears and pressure gradients, and corresponding flow-induced MRRs, are, in turn, found to scale as √A /do ω, where A is the vibration amplitude, do is the characteristic gap thickness between the tool and workpiece, and ω is the vibration frequency. In the large-amplitude limit, A ≳ 5 μm, experimental measurements and a simple scaling argument show that the polishing slurry film becomes thick enough that the workpiece and polishing tool lose direct contact. In this limit, observed MRRs thus reflect

Electricity of machine tool

International Nuclear Information System (INIS)

Gijeon media editorial department

1977-10-01

This book is divided into three parts. The first part deals with electricity machine, which can taints from generator to motor, motor a power source of machine tool, electricity machine for machine tool such as switch in main circuit, automatic machine, a knife switch and pushing button, snap switch, protection device, timer, solenoid, and rectifier. The second part handles wiring diagram. This concludes basic electricity circuit of machine tool, electricity wiring diagram in your machine like milling machine, planer and grinding machine. The third part introduces fault diagnosis of machine, which gives the practical solution according to fault diagnosis and the diagnostic method with voltage and resistance measurement by tester.

Removing Chinese privet from riparian forests still benefits pollinators five years later

Science.gov (United States)

Jacob R. Hudson; James Hanula; Scott Horn

2014-01-01

Chinese privet (Ligustrum sinense) is an invasive shrub of the Southeastern U.S. that forms dense stands and limits biodiversity. It was removed from heavily infested riparian forests of the Georgia Piedmont in 2005 by mulching machine or chainsaw felling and subsequent herbicide application. Abundance and species richness of bees and butterflies...

Machine medical ethics

CERN Document Server

Pontier, Matthijs

2015-01-01

The essays in this book, written by researchers from both humanities and sciences, describe various theoretical and experimental approaches to adding medical ethics to a machine in medical settings. Medical machines are in close proximity with human beings, and getting closer: with patients who are in vulnerable states of health, who have disabilities of various kinds, with the very young or very old, and with medical professionals. In such contexts, machines are undertaking important medical tasks that require emotional sensitivity, knowledge of medical codes, human dignity, and privacy. As machine technology advances, ethical concerns become more urgent: should medical machines be programmed to follow a code of medical ethics? What theory or theories should constrain medical machine conduct? What design features are required? Should machines share responsibility with humans for the ethical consequences of medical actions? How ought clinical relationships involving machines to be modeled? Is a capacity for e...

Humanizing machines: Anthropomorphization of slot machines increases gambling.

Science.gov (United States)

Riva, Paolo; Sacchi, Simona; Brambilla, Marco

2015-12-01

Do people gamble more on slot machines if they think that they are playing against humanlike minds rather than mathematical algorithms? Research has shown that people have a strong cognitive tendency to imbue humanlike mental states to nonhuman entities (i.e., anthropomorphism). The present research tested whether anthropomorphizing slot machines would increase gambling. Four studies manipulated slot machine anthropomorphization and found that exposing people to an anthropomorphized description of a slot machine increased gambling behavior and reduced gambling outcomes. Such findings emerged using tasks that focused on gambling behavior (Studies 1 to 3) as well as in experimental paradigms that included gambling outcomes (Studies 2 to 4). We found that gambling outcomes decrease because participants primed with the anthropomorphic slot machine gambled more (Study 4). Furthermore, we found that high-arousal positive emotions (e.g., feeling excited) played a role in the effect of anthropomorphism on gambling behavior (Studies 3 and 4). Our research indicates that the psychological process of gambling-machine anthropomorphism can be advantageous for the gaming industry; however, this may come at great expense for gamblers' (and their families') economic resources and psychological well-being. (c) 2015 APA, all rights reserved).

Model Predictive Engine Air-Ratio Control Using Online Sequential Relevance Vector Machine

Directory of Open Access Journals (Sweden)

Hang-cheong Wong

2012-01-01

Full Text Available Engine power, brake-specific fuel consumption, and emissions relate closely to air ratio (i.e., lambda among all the engine variables. An accurate and adaptive model for lambda prediction is essential to effective lambda control for long term. This paper utilizes an emerging technique, relevance vector machine (RVM, to build a reliable time-dependent lambda model which can be continually updated whenever a sample is added to, or removed from, the estimated lambda model. The paper also presents a new model predictive control (MPC algorithm for air-ratio regulation based on RVM. This study shows that the accuracy, training, and updating time of the RVM model are superior to the latest modelling methods, such as diagonal recurrent neural network (DRNN and decremental least-squares support vector machine (DLSSVM. Moreover, the control algorithm has been implemented on a real car to test. Experimental results reveal that the control performance of the proposed relevance vector machine model predictive controller (RVMMPC is also superior to DRNNMPC, support vector machine-based MPC, and conventional proportional-integral (PI controller in production cars. Therefore, the proposed RVMMPC is a promising scheme to replace conventional PI controller for engine air-ratio control.

Technical improvement of arch setting machine for roadway drive. Kusshin kirihayo sewakuki no hensen

Energy Technology Data Exchange (ETDEWEB)

Fujino, T [Taiheiyo Coal Mining Co. Ltd., Tokyo (Japan)

1991-09-25

The following contents are described for a new type arch setting machine introduced to the Taiheiyo Coal Mining Co. (1) The excavation of drift in this coal mine is carried out by the excavating system combining the excavating machine (CM) and the transporter (SC) and the supporting method where arch type steel beams are used as the supporting material is used. (2) In order to automatize the arch setting work, this machine which combined the both functions of the arch lifter (developed in 1983) and the arch setting manipulator (ASM, developed in 1990). (3) This machine has the total weight of 1,500kg, is mounted on CM, and consists of the running part, the arm part, the boom part, and the end saucer part of steel arches. Further, simple fitting or removing can be made and the coal falling down is prevented by holding the coal wall during the arch setting work. (4) When this machine and the ASM were compared for the arch setting time in the working site, the former required about the half time period of the latter. 5 figs., 1 tab.

Compressive Strength Prediction of Square Concrete Columns Retrofitted with External Steel Collars

Directory of Open Access Journals (Sweden)

Pudjisuryadi, P.

2013-01-01

Full Text Available Transverse confining stress in concrete members, commonly provided by transverse reinforcement, has been recognized to enhance strength and ductility. Nowadays, the confining method has been further developed to external confinement approach. This type of confinement can be used for retrofitting existing concrete columns. Many external confining techniques have been proven to be successful in retrofitting circular columns. However, for square or rectangular columns, providing effective confining stress by external retrofitting method is not a simple task due to high stress concentration at column’s corners. This paper proposes an analytical model to predict the peak strength of square concrete columns confined by external steel collars. Comparison with the experimental results showed that the model can predict the peak strength reasonably well. However, it should be noted that relatively larger amount of steel is needed to achieve comparable column strength enhancement when it is compared with those of conve tional internally-confined columns.

Study on Integration Treatment Technology of Waste Emulsion from Machining Processing

OpenAIRE

Xin-dong Li; Wan-fu Huang

2013-01-01

The study studied the treatment technology of high concentration emulsion wastewater in metal machining plant. By analyzing the properties of emulsion wastewater, the author used the combination process of membrane technology + Fe-C micro-electrolysis + membrane bioreactor to treat the wastewater. Through the ceramic membrane, the removal rate of CODCr can reach 95%. Fe-C micro-electrolysis treatment can improve the biodegradability of wastewater, lastly through the membrane bioreactor treatm...

Code-expanded radio access protocol for machine-to-machine communications

DEFF Research Database (Denmark)

Thomsen, Henning; Kiilerich Pratas, Nuno; Stefanovic, Cedomir

2013-01-01

The random access methods used for support of machine-to-machine, also referred to as Machine-Type Communications, in current cellular standards are derivatives of traditional framed slotted ALOHA and therefore do not support high user loads efficiently. We propose an approach that is motivated b...... subframes and orthogonal preambles, the amount of available contention resources is drastically increased, enabling the massive support of Machine-Type Communication users that is beyond the reach of current systems.......The random access methods used for support of machine-to-machine, also referred to as Machine-Type Communications, in current cellular standards are derivatives of traditional framed slotted ALOHA and therefore do not support high user loads efficiently. We propose an approach that is motivated...... by the random access method employed in LTE, which significantly increases the amount of contention resources without increasing the system resources, such as contention subframes and preambles. This is accomplished by a logical, rather than physical, extension of the access method in which the available system...

Online Artifact Removal for Brain-Computer Interfaces Using Support Vector Machines and Blind Source Separation

OpenAIRE

Halder, Sebastian; Bensch, Michael; Mellinger, Jürgen; Bogdan, Martin; Kübler, Andrea; Birbaumer, Niels; Rosenstiel, Wolfgang

2007-01-01

We propose a combination of blind source separation (BSS) and independent component analysis (ICA) (signal decomposition into artifacts and nonartifacts) with support vector machines (SVMs) (automatic classification) that are designed for online usage. In order to select a suitable BSS/ICA method, three ICA algorithms (JADE, Infomax, and FastICA) and one BSS algorithm (AMUSE) are evaluated to determine their ability to isolate electromyographic (EMG) and electrooculographic...

Tyrosine Kinase Ligand-Receptor Pair Prediction by Using Support Vector Machine

Directory of Open Access Journals (Sweden)

Masayuki Yarimizu

2015-01-01

Full Text Available Receptor tyrosine kinases are essential proteins involved in cellular differentiation and proliferation in vivo and are heavily involved in allergic diseases, diabetes, and onset/proliferation of cancerous cells. Identifying the interacting partner of this protein, a growth factor ligand, will provide a deeper understanding of cellular proliferation/differentiation and other cell processes. In this study, we developed a method for predicting tyrosine kinase ligand-receptor pairs from their amino acid sequences. We collected tyrosine kinase ligand-receptor pairs from the Database of Interacting Proteins (DIP and UniProtKB, filtered them by removing sequence redundancy, and used them as a dataset for machine learning and assessment of predictive performance. Our prediction method is based on support vector machines (SVMs, and we evaluated several input features suitable for tyrosine kinase for machine learning and compared and analyzed the results. Using sequence pattern information and domain information extracted from sequences as input features, we obtained 0.996 of the area under the receiver operating characteristic curve. This accuracy is higher than that obtained from general protein-protein interaction pair predictions.

Stress and fatigue analysis of fuelling machine housing of 500 MWe PHWR

International Nuclear Information System (INIS)

Dutta, B.K.; Ramana, W.V.; Kushwaha, H.S.; Kakodkar, A.

1987-01-01

One of the most appealing features of the Pressurised Heavy Water Reactors is the online refuelling capability. For this a fuelling machine is used. This machine opens a reactor channel by removing a seal plug and a shield plug and then does the necessary fuelling by pushing fuel bundles from a fuel magazine by rams. After necessary fuelling the machine closes the channel automatically. One of the most important parts of the fuelling machine is its pressure housing which becomes a part of the reactor channel during refuelling operation. It houses the fuel magazine, separators and rams. Beside channel pressure and other mechanical loads, the pressure housing experiences thermal transients during refuelling. The housing consists of two cylindrical shells having one end-closer in each. They are connected with each other by a large sized coupling. There are many holes on both the end-closers to accommodate ram movement, separators and magazine rive mechanisms. Some of these holes intersect with each other in the housing end-closers and hence end-closers are reinforced accordingly. This also makes the end-closers nonsymmetric. In the following sections the various analysis done to compute general stress distribution, stress concentration factors near to various holes, temperature transients during refuelling and also allowable fatigue cycles for pressure housing of fuelling machine for the proposed 500 MWe are described. (orig.)

Stress and fatigue analysis of fuelling machine housing of 500 MWe PHWR

International Nuclear Information System (INIS)

Dutta, B.K.; Ramana, W.V.; Kushwaha, H.S.; Kakodkar, A.

1987-01-01

One of the most appealing features of the Pressurised Heavy Water Reactors is the online refuelling capability. For this a fuelling machine is used. This machine opens a reactor channel by removing a seal plug and a shield plug and then does the necessary fuelling by pushing fuel bundles from a fuel magazine by rams. After necessary fuelling the machine closes the channel automatically. One of the most important parts of the fuelling machine is its pressure housing which becomes a part of the reactor channel during refuelling operation. It houses the fuel magazine, separators and rams. Beside channel pressure and other mechanical loads, the pressure housing experiences thermal transients during refuelling. The housing consists of two cylindrical shells having one end-closer in each. They are connected with each other by a large sized coupling. There are many holes on both the end-closers to accommodate ram movement, separators and magazine drive mechanisms. Some of these holes intersect with each other in the housing end-closures and hence end-closures are reinforced accordingly. This also makes the end-closures nonsymmetric. In the following sections the various analysis done to compute general stress distribution, stress concentration factors near to various holes, temperature transients during refuelling and also allowable fatigue cycles for pressure housing of fuelling machine for the proposed 500 MWe are described

Pileup Mitigation with Machine Learning (PUMML)

Science.gov (United States)

Komiske, Patrick T.; Metodiev, Eric M.; Nachman, Benjamin; Schwartz, Matthew D.

2017-12-01

Pileup involves the contamination of the energy distribution arising from the primary collision of interest (leading vertex) by radiation from soft collisions (pileup). We develop a new technique for removing this contamination using machine learning and convolutional neural networks. The network takes as input the energy distribution of charged leading vertex particles, charged pileup particles, and all neutral particles and outputs the energy distribution of particles coming from leading vertex alone. The PUMML algorithm performs remarkably well at eliminating pileup distortion on a wide range of simple and complex jet observables. We test the robustness of the algorithm in a number of ways and discuss how the network can be trained directly on data.

Simple machines

CERN Document Server

Graybill, George

2007-01-01

Just how simple are simple machines? With our ready-to-use resource, they are simple to teach and easy to learn! Chocked full of information and activities, we begin with a look at force, motion and work, and examples of simple machines in daily life are given. With this background, we move on to different kinds of simple machines including: Levers, Inclined Planes, Wedges, Screws, Pulleys, and Wheels and Axles. An exploration of some compound machines follows, such as the can opener. Our resource is a real time-saver as all the reading passages, student activities are provided. Presented in s

Machine performance assessment and enhancement for a hexapod machine

Energy Technology Data Exchange (ETDEWEB)

Mou, J.I. [Arizona State Univ., Tempe, AZ (United States); King, C. [Sandia National Labs., Livermore, CA (United States). Integrated Manufacturing Systems Center

1998-03-19

The focus of this study is to develop a sensor fused process modeling and control methodology to model, assess, and then enhance the performance of a hexapod machine for precision product realization. Deterministic modeling technique was used to derive models for machine performance assessment and enhancement. Sensor fusion methodology was adopted to identify the parameters of the derived models. Empirical models and computational algorithms were also derived and implemented to model, assess, and then enhance the machine performance. The developed sensor fusion algorithms can be implemented on a PC-based open architecture controller to receive information from various sensors, assess the status of the process, determine the proper action, and deliver the command to actuators for task execution. This will enhance a hexapod machine`s capability to produce workpieces within the imposed dimensional tolerances.

Superconducting rotating machines

International Nuclear Information System (INIS)

Smith, J.L. Jr.; Kirtley, J.L. Jr.; Thullen, P.

1975-01-01

The opportunities and limitations of the applications of superconductors in rotating electric machines are given. The relevant properties of superconductors and the fundamental requirements for rotating electric machines are discussed. The current state-of-the-art of superconducting machines is reviewed. Key problems, future developments and the long range potential of superconducting machines are assessed

Sustainable machining

CERN Document Server

2017-01-01

This book provides an overview on current sustainable machining. Its chapters cover the concept in economic, social and environmental dimensions. It provides the reader with proper ways to handle several pollutants produced during the machining process. The book is useful on both undergraduate and postgraduate levels and it is of interest to all those working with manufacturing and machining technology.

Research status in ultra-precision machining of silicon carbide parts by oxidation-assisted polishing

Directory of Open Access Journals (Sweden)

Xinmin SHEN

2016-10-01

Full Text Available Oxidation-assisted polishing is an important machining method for obtaining SiC parts with high precision. Through plasma oxidation, thermal oxidation, and anodic oxidation, soft oxide can be obtained on the RS-SiC substrate. With the assistance of abrasive polishing to remove the oxide rapidly, the material removal rate can be increased and the surface quality can be improved. The research results indicate that the surface roughness root-mean-square (RMS and roughness-average (Ra can reach 0.626 nm and 0.480 nm by plasma oxidation-assisted polishing; in thermal oxidation-assisted polishing, the RMS and Ra can be 0.920 nm and 0.726 nm; in anodic oxidation, the calculated oxidation rate is 5.3 nm/s based on Deal-Grove model, and the RMS and Ra are 4.428 nm and 3.453 nm respectively in anodic oxidation-assisted polishing. The oxidation-assisted polishing can be propitious to improve the process level in machining RS-SiC, which would promote the application of SiC parts in optics and ceramics fields.

Multi-response optimization of machining characteristics in ultrasonic machining of WC-Co composite through Taguchi method and grey-fuzzy logic

Directory of Open Access Journals (Sweden)

Ravi Pratap Singh

2018-01-01

Full Text Available This article addresses the application of grey based fuzzy logic coupled with Taguchi’s approach for optimization of multi performance characteristics in ultrasonic machining of WC-Co composite material. The Taguchi’s L-36 array has been employed to conduct the experimentation and also to observe the influence of different process variables (power rating, cobalt content, tool geometry, thickness of work piece, tool material, abrasive grit size on machining characteristics. Grey relational fuzzy grade has been computed by converting the multiple responses, i.e., material removal rate and tool wear rate obtained from Taguchi’s approach into a single performance characteristic using grey based fuzzy logic. In addition, analysis of variance (ANOVA has also been attempted in a view to identify the significant parameters. Results revealed grit size and power rating as leading parameters for optimization of multi performance characteristics. From the microstructure analysis, the mode of material deformation has been observed and the critical parameters (i.e., work material properties, grit size, and power rating for the deformation mode have been established.

Advanced Electrical Machines and Machine-Based Systems for Electric and Hybrid Vehicles

Directory of Open Access Journals (Sweden)

Ming Cheng

2015-09-01

Full Text Available The paper presents a number of advanced solutions on electric machines and machine-based systems for the powertrain of electric vehicles (EVs. Two types of systems are considered, namely the drive systems designated to the EV propulsion and the power split devices utilized in the popular series-parallel hybrid electric vehicle architecture. After reviewing the main requirements for the electric drive systems, the paper illustrates advanced electric machine topologies, including a stator permanent magnet (stator-PM motor, a hybrid-excitation motor, a flux memory motor and a redundant motor structure. Then, it illustrates advanced electric drive systems, such as the magnetic-geared in-wheel drive and the integrated starter generator (ISG. Finally, three machine-based implementations of the power split devices are expounded, built up around the dual-rotor PM machine, the dual-stator PM brushless machine and the magnetic-geared dual-rotor machine. As a conclusion, the development trends in the field of electric machines and machine-based systems for EVs are summarized.

Asynchronized synchronous machines

CERN Document Server

Botvinnik, M M

1964-01-01

Asynchronized Synchronous Machines focuses on the theoretical research on asynchronized synchronous (AS) machines, which are "hybrids” of synchronous and induction machines that can operate with slip. Topics covered in this book include the initial equations; vector diagram of an AS machine; regulation in cases of deviation from the law of full compensation; parameters of the excitation system; and schematic diagram of an excitation regulator. The possible applications of AS machines and its calculations in certain cases are also discussed. This publication is beneficial for students and indiv

Qualitative Evaluation of the Five-Year 'Red Collar' Campaign to End Inhumane Culling of Dogs as a Method of Rabies Control.

Science.gov (United States)

Hiby, Elly; Tasker, Lou

2018-02-06

Dog-mediated human rabies can be eliminated through mass dog vaccination. Despite leading authorities in human and animal health uniting to advance effective and humane rabies control, some governments resort to lethal methods, which are unethical, often inhumane and ineffective. To end the inhumane culling of dogs in response to rabies, World Animal Protection launched 'Red Collar'; a five-year campaign (2011-2016) that worked with governments to promote the implementation of mass dog vaccination for rabies control. We present the findings from a qualitative evaluation of 'Red Collar', conducted both regionally and with national focus on Bangladesh, China, Indonesia, the Philippines and Zanzibar, Tanzania. Through semi-structured interviews and written contributions from stakeholders ( n = 54), we compared perceptions of changes with stated campaign goals to capture recommendations for future work. The campaign successfully generated momentum for implementation of mass dog vaccination by targeted governments. Lessons learned were established: Value of a consistent animal welfare 'voice'; the need to explore the motivations behind culling; the need to capacity build; time required for the 'ripple effect' to inspire humane control in other countries; importance of monitoring and evaluation of indicators; time and effort required for exit strategies and prior preparation for a robust response to culling.

Parametric optimization during machining of AISI 304 Austenitic Stainless Steel using CVD coated DURATOMIC cutting insert

Directory of Open Access Journals (Sweden)

M. Kaladhar

2012-08-01

Full Text Available In this work, Taguchi method is applied to determine the optimum process parameters for turning of AISI 304 austenitic stainless steel on CNC lathe. A Chemical vapour deposition (CVD coated cemented carbide cutting insert is used which is produced by DuratomicTM technology of 0.4 and 0.8 mm nose radii. The tests are conducted at four levels of Cutting speed, feed and depth of cut. The influence of these parameters are investigated on the surface roughness and material removal rate (MRR. The Analysis Of Variance (ANOVA is also used to analyze the influence of cutting parameters during machining. The results revealed that cutting speed significantly (46.05% affected the machined surface roughness values followed by nose radius (23.7%. The influence of the depth of cut (61.31% in affecting material removal rate (MRR is significantly large. The cutting speed (20.40% is the next significant factor. Optimal range and optimal level of parameters are also predicted for responses.

Machine Shop Lathes.

Science.gov (United States)

Dunn, James

This guide, the second in a series of five machine shop curriculum manuals, was designed for use in machine shop courses in Oklahoma. The purpose of the manual is to equip students with basic knowledge and skills that will enable them to enter the machine trade at the machine-operator level. The curriculum is designed so that it can be used in…

A COMPUTERIZED DIAGNOSTIC COMPLEX FOR RELIABILITY TESTING OF ELECTRIC MACHINES

Directory of Open Access Journals (Sweden)

O.О. Somka

2015-06-01

Full Text Available Purpose. To develop a diagnostic complex meeting the criteria and requirements for carrying out accelerated reliability test and realizing the basic modes of electric machines operation and performance of the posed problems necessary in the process of such test. Methodology. To determine and forecast the indices of electric machines reliability in accordance with the statistic data of repair plants we have conditionally divided them into structural parts that are most likely to fail. We have preliminarily assessed the state of each of these parts, which includes revelation of faults and deviations of technical and geometric parameters. We have determined the analyzed electric machine controlled parameters used for assessment of quantitative characteristics of reliability of these parts and electric machines on the whole. Results. As a result of the research, we have substantiated the structure of a computerized complex for electric machines reliability test. It allows us to change thermal and vibration actions without violation of the physics of the processes of aging and wearing of the basic structural parts and elements material. The above mentioned makes it possible to considerably reduce time spent on carrying out electric machines reliability tests and improve trustworthiness of the data obtained as a result of their performance. Originality. A special feature of determination of the controlled parameters consists in removal of vibration components in the idle mode and after disconnection of the analyzed electric machine from the power supply with the aim of singling out the vibration electromagnetic component, fixing the degree of sparking and bend of the shaft by means of phototechnique and local determination of structural parts temperature provided by corresponding location of thermal sensors. Practical value. We have offered a scheme of location of thermal and vibration sensors, which allows improvement of parameters measuring accuracy

Investigation of the removing process of cathode material in micro-EDM using an atomistic-continuum model

International Nuclear Information System (INIS)

Guo, Jianwen; Zhang, Guojun; Huang, Yu; Ming, Wuyi; Liu, Min; Huang, Hao

2014-01-01

Highlights: • An atomistic-continuum computational simulation model for single-discharge micro-EDM process of Cu cathode is constructed. • Cathode material is removed mainly in the form of single atoms or small clusters in micro-EDM. • Electric action leads to the formation of peaks on the surface of crater. • Removing process of cathode material under the hybrid action combining the thermal action and the electric action is studied, and the strength of either action needed for material to remove is much reduced. - Abstract: In micro-electrical discharge machining (micro-EDM), the discharge duration is ultra-short, and both the electric action and the thermal action by the discharge channel play important roles in the removing process of cathode material. However, in most researches on the machining mechanism of micro-EDM, only the thermal action is concerned. In this article, a combined atomistic-continuum modeling method in which the two-temperature model and the molecular dynamics simulation model are integrated is used to construct the simulation model for cathode in single-discharge micro-EDM process. With this simulation model, removing processes of Cu cathode material in micro-EDM under pure thermal action, pure electric action and the combination of them are investigated in a simulative way. By analyzing evolutions of temperature, stress and micro-structure of material as well as the dynamical behaviors of material in the removing process, mechanisms of the cathode material removal and crater formation are revealed. In addition, the removing process of cathode material under the combination of pure thermal action and pure electric action is compared with those under the two pure actions respectively to analyze the interactive effect between the thermal action and the electric action

Study on the Optimization and Process Modeling of the Rotary Ultrasonic Machining of Zerodur Glass-Ceramic

Science.gov (United States)

Pitts, James Daniel

Rotary ultrasonic machining (RUM), a hybrid process combining ultrasonic machining and diamond grinding, was created to increase material removal rates for the fabrication of hard and brittle workpieces. The objective of this research was to experimentally derive empirical equations for the prediction of multiple machined surface roughness parameters for helically pocketed rotary ultrasonic machined Zerodur glass-ceramic workpieces by means of a systematic statistical experimental approach. A Taguchi parametric screening design of experiments was employed to systematically determine the RUM process parameters with the largest effect on mean surface roughness. Next empirically determined equations for the seven common surface quality metrics were developed via Box-Behnken surface response experimental trials. Validation trials were conducted resulting in predicted and experimental surface roughness in varying levels of agreement. The reductions in cutting force and tool wear associated with RUM, reported by previous researchers, was experimentally verified to also extended to helical pocketing of Zerodur glass-ceramic.

Better Few than Hungry: Flexible Feeding Ecology of Collared Lemurs Eulemur collaris in Littoral Forest Fragments

Science.gov (United States)

Donati, Giuseppe; Kesch, Kristina; Ndremifidy, Kelard; Schmidt, Stacey L.; Ramanamanjato, Jean-Baptiste; Borgognini-Tarli, Silvana M.; Ganzhorn, Joerg U.

2011-01-01

Background Frugivorous primates are known to encounter many problems to cope with habitat degradation, due to the fluctuating spatial and temporal distribution of their food resources. Since lemur communities evolved strategies to deal with periods of food scarcity, these primates are expected to be naturally adapted to fluctuating ecological conditions and to tolerate a certain degree of habitat changes. However, behavioral and ecological strategies adopted by frugivorous lemurs to survive in secondary habitats have been little investigated. Here, we compared the behavioral ecology of collared lemurs (Eulemur collaris) in a degraded fragment of littoral forest of south-east Madagascar, Mandena, with that of their conspecifics in a more intact habitat, Sainte Luce. Methodology/Principal Findings Lemur groups in Mandena and in Sainte Luce were censused in 2004/2007 and in 2000, respectively. Data were collected via instantaneous sampling on five lemur groups totaling 1,698 observation hours. The Shannon index was used to determine dietary diversity and nutritional analyses were conducted to assess food quality. All feeding trees were identified and measured, and ranging areas determined via the minimum convex polygon. In the degraded area lemurs were able to modify several aspects of their feeding strategies by decreasing group size and by increasing feeding time, ranging areas, and number of feeding trees. The above strategies were apparently able to counteract a clear reduction in both food quality and size of feeding trees. Conclusions/Significance Our findings indicate that collared lemurs in littoral forest fragments modified their behavior to cope with the pressures of fluctuating resource availability. The observed flexibility is likely to be an adaptation to Malagasy rainforests, which are known to undergo periods of fruit scarcity and low productivity. These results should be carefully considered when relocating lemurs or when selecting suitable areas for

Beamlines at synchrotron radiation facilities: The link between the user and the machine

International Nuclear Information System (INIS)

Johnson, E.D.; Hulbert, S.L.; Berman, L.E.

1991-12-01

At this point in time the literature is full of excellent review articles which describe the operating principles of optical systems for utilizing the unique radiation provided by synchrotron storage rings. In general, the perspective provided by this body of work is that of the end user-experimenter cum optics designer. Nominal design specifications of the accelerator are usually assumed, and the impact of operation in a performance envelope which may represent either degraded or enhanced machine performance is seldom considered. In this article, we have attempted to remove ourselves from this (our own usual) perspective and look instead at the beamline as a transfer function to map from the machine to the users experiment. We open first with an introduction to the perspective of the experimentalist, and some general considerations for the interaction of beamline hardware with the machine. We then discuss phase space representations of some common components of beamlines, and then treat some important classes of crystal and geometric optics in monochromators. We then close with a discussion of some of the common features of these optical systems, and the impact of the machine on user experiments

Review of selected coil and collared-coil assembly data from 10-M-long, 50-MM-Twin-aperture LHC dipole magnet prototypes

International Nuclear Information System (INIS)

Devred, A.

1999-02-01

In 1991, the Laboratoire Europeen pour la Physique des Particules (CERN) has launched the fabrication in industry of seven 10 m long, 50 mm twin aperture dipole magnet prototypes for the Large Hadron Collider (LHC). The design and specific features of these magnets have been described elsewhere. In this paper, we review some of the coil and collared-coil assembly data and we analyze the influence of tooling imperfections on magnet assembly. (author)

Improved Extreme Learning Machine based on the Sensitivity Analysis

Science.gov (United States)

Cui, Licheng; Zhai, Huawei; Wang, Benchao; Qu, Zengtang

2018-03-01

Extreme learning machine and its improved ones is weak in some points, such as computing complex, learning error and so on. After deeply analyzing, referencing the importance of hidden nodes in SVM, an novel analyzing method of the sensitivity is proposed which meets people’s cognitive habits. Based on these, an improved ELM is proposed, it could remove hidden nodes before meeting the learning error, and it can efficiently manage the number of hidden nodes, so as to improve the its performance. After comparing tests, it is better in learning time, accuracy and so on.

Machining of Machine Elements Made of Polymer Composite Materials

Science.gov (United States)

Baurova, N. I.; Makarov, K. A.

2017-12-01

The machining of the machine elements that are made of polymer composite materials (PCMs) or are repaired using them is considered. Turning, milling, and drilling are shown to be most widely used among all methods of cutting PCMs. Cutting conditions for the machining of PCMs are presented. The factors that most strongly affect the roughness parameters and the accuracy of cutting PCMs are considered.

Work-related stress and quality of life among Iranian blue-collar workers with self-reported low back pain.

Science.gov (United States)

Kabir-Mokamelkhah, Elaheh; Bahrami-Ahmadi, Amir; Aghili, Negar

2016-01-01

Background: Impairment in quality of life and mental health had been reported in the previous studies as the results of musculoskeletal disorders among workers. Mental health has a wide concept and contains different disorders including anxiety, depression or even decreased quality of life, all of which having challengeable impacts on work- related characters such as work productivity and absensism. The present study aimed at evaluating work- related stress and quality of life among Iranian blue-collar workers of Fars ABFA Company with selfreported low back pain. Methods: In the present study, we focused on the low back pain among 451 blue-collar workers and assessed their work- related stress and quality of life status using DASS-21 and short form questionnaire (SF-36), respectively. Independent sample t-test was used to compare the qualitative variables, and chi-square test was utilized for statistical analysis of the qualitative variables. Results: Mean of the total score of quality of life among workers with low back pain was significantly lower than in those workers without low back pain. The mean of work- related stress score was significantly higher in workers with low back pain than in workers without low back pain. The mean quality of life subdomains in patients with low back pain was significantly lower than in workers without low back pain. Conclusion: Findings of the present study revealed that workers with low back pain had lower quality of life score and higher work- related stress score. These findings should be considered in designing preventive programs rather than controlling the pain.

Pentek metal coating removal system: Baseline report

International Nuclear Information System (INIS)

1997-01-01

The Pentek coating removal technology was tested and is being evaluated at Florida International University (FIU) as a baseline technology. In conjunction with FIU's evaluation of efficiency and cost, this report covers evaluation conducted for safety and health issues. It is a commercially available technology and has been used for various projects at locations throughout the country. The Pentek coating removal system consisted of the ROTO-PEEN Scaler, CORNER-CUTTER reg-sign, and VAC-PAC reg-sign. They are designed to remove coatings from steel, concrete, brick, and wood. The Scaler uses 3M Roto Peen tungsten carbide cutters while the CORNER-CUTTER reg-sign uses solid needles for descaling activities. These hand tools are used with the VAC-PAC reg-sign vacuum system to capture dust and debris as removal of the coating takes place. The safety and health evaluation during the testing demonstration focused on two main areas of exposure: dust and noise. Dust exposure minimal, but noise exposure was significant. Further testing for each exposure is recommended because of the environment where the testing demonstration took place. It is feasible that the dust and noise levels will be higher in an enclosed operating environment of different construction. In addition, other areas of concern found were arm-hand vibration, whole-body, ergonomics, heat stress, tripping hazards, electrical hazards, machine guarding, and lockout/tagout

Changing Workplaces to Reduce Work-Family Conflict: Schedule Control in a White-Collar Organization.

Science.gov (United States)

Kelly, Erin L; Moen, Phyllis; Tranby, Eric

2011-04-01

Work-family conflicts are common and consequential for employees, their families, and work organizations. Can workplaces be changed to reduce work-family conflict? Previous research has not been able to assess whether workplace policies or initiatives succeed in reducing work-family conflict or increasing work-family fit. Using longitudinal data collected from 608 employees of a white-collar organization before and after a workplace initiative was implemented, we investigate whether the initiative affects work-family conflict and fit, whether schedule control mediates these effects, and whether work demands, including long hours, moderate the initiative's effects on work-family outcomes. Analyses clearly demonstrate that the workplace initiative positively affects the work-family interface, primarily by increasing employees' schedule control. This study points to the importance of schedule control for our understanding of job quality and for management policies and practices.

Determination of U-235 quantity in fresh fuel elements by neutron coincidence collar technique

International Nuclear Information System (INIS)

Almeida, M.C.M. de; Almeida, S.G. de; Marzo, M.A.S.; Moita, L.P.M.

1990-01-01

The U-235 quantity per lenght of fresh fuel assemblies of the Angra-I first recharge was determined by Neutron Coincidence Collar technique (N.C.C.). This technique is well-founded in fresh fuel assemblies activation by thermal neutrons from AmLi source to generate U-235 fission neutrons. These neutrons are detected by coincidence method in polyethylene structure where 18 He-3 detectors were placed. The coincidence counting results, in active mode (AmLi), showed 0,7% to standard deviation and equal to 1,49% to mass in 1000s of counting. The accuracies of different calibration methods were evaluated and compared. The results showed that the operator declared values are consistent. This evaluation was part of technical-exchange program between Safeguards Laboratory from C.N.E.N. and Los Alamos National Lab., United States. (author)

Improving Machining Accuracy of CNC Machines with Innovative Design Methods

Science.gov (United States)

Yemelyanov, N. V.; Yemelyanova, I. V.; Zubenko, V. L.

2018-03-01

The article considers achieving the machining accuracy of CNC machines by applying innovative methods in modelling and design of machining systems, drives and machine processes. The topological method of analysis involves visualizing the system as matrices of block graphs with a varying degree of detail between the upper and lower hierarchy levels. This approach combines the advantages of graph theory and the efficiency of decomposition methods, it also has visual clarity, which is inherent in both topological models and structural matrices, as well as the resiliency of linear algebra as part of the matrix-based research. The focus of the study is on the design of automated machine workstations, systems, machines and units, which can be broken into interrelated parts and presented as algebraic, topological and set-theoretical models. Every model can be transformed into a model of another type, and, as a result, can be interpreted as a system of linear and non-linear equations which solutions determine the system parameters. This paper analyses the dynamic parameters of the 1716PF4 machine at the stages of design and exploitation. Having researched the impact of the system dynamics on the component quality, the authors have developed a range of practical recommendations which have enabled one to reduce considerably the amplitude of relative motion, exclude some resonance zones within the spindle speed range of 0...6000 min-1 and improve machining accuracy.

The achievements of the Z-machine; Les exploits de la Z-machine

Energy Technology Data Exchange (ETDEWEB)

Larousserie, D

2008-03-15

The ZR-machine that represents the latest generation of Z-pinch machines has recently begun preliminary testing before its full commissioning in Albuquerque (Usa). During its test the machine has well operated with electrical currents whose intensities of 26 million Ampere are already 2 times as high as the intensity of the operating current of the previous Z-machine. In 2006 the Z-machine reached temperatures of 2 billions Kelvin while 100 million Kelvin would be sufficient to ignite thermonuclear fusion. In fact the concept of Z-pinch machines was imagined in the fifties but the technological breakthrough that has allowed this recent success and the reborn of Z-machine, was the replacement of gas by an array of metal wires through which the electrical current flows and vaporizes it creating an imploding plasma. It is not well understood why Z-pinch machines generate far more radiation than theoretically expected. (A.C.)

Prediction of mortality after radical cystectomy for bladder cancer by machine learning techniques.

Science.gov (United States)

Wang, Guanjin; Lam, Kin-Man; Deng, Zhaohong; Choi, Kup-Sze

2015-08-01

Bladder cancer is a common cancer in genitourinary malignancy. For muscle invasive bladder cancer, surgical removal of the bladder, i.e. radical cystectomy, is in general the definitive treatment which, unfortunately, carries significant morbidities and mortalities. Accurate prediction of the mortality of radical cystectomy is therefore needed. Statistical methods have conventionally been used for this purpose, despite the complex interactions of high-dimensional medical data. Machine learning has emerged as a promising technique for handling high-dimensional data, with increasing application in clinical decision support, e.g. cancer prediction and prognosis. Its ability to reveal the hidden nonlinear interactions and interpretable rules between dependent and independent variables is favorable for constructing models of effective generalization performance. In this paper, seven machine learning methods are utilized to predict the 5-year mortality of radical cystectomy, including back-propagation neural network (BPN), radial basis function (RBFN), extreme learning machine (ELM), regularized ELM (RELM), support vector machine (SVM), naive Bayes (NB) classifier and k-nearest neighbour (KNN), on a clinicopathological dataset of 117 patients of the urology unit of a hospital in Hong Kong. The experimental results indicate that RELM achieved the highest average prediction accuracy of 0.8 at a fast learning speed. The research findings demonstrate the potential of applying machine learning techniques to support clinical decision making. Copyright © 2015 Elsevier Ltd. All rights reserved.

Quantum machine learning.

Science.gov (United States)

Biamonte, Jacob; Wittek, Peter; Pancotti, Nicola; Rebentrost, Patrick; Wiebe, Nathan; Lloyd, Seth

2017-09-13

Fuelled by increasing computer power and algorithmic advances, machine learning techniques have become powerful tools for finding patterns in data. Quantum systems produce atypical patterns that classical systems are thought not to produce efficiently, so it is reasonable to postulate that quantum computers may outperform classical computers on machine learning tasks. The field of quantum machine learning explores how to devise and implement quantum software that could enable machine learning that is faster than that of classical computers. Recent work has produced quantum algorithms that could act as the building blocks of machine learning programs, but the hardware and software challenges are still considerable.

MRR and TWR evaluation on electrical discharge machining of Ti-6Al-4V using tungsten : copper composite electrode

Science.gov (United States)

Prasanna, J.; Rajamanickam, S.; Amith Kumar, O.; Karthick Raj, G.; Sathya Narayanan, P. V. V.

2017-05-01

In this paper Ti-6Al-4V used as workpiece material and it is keenly seen in variety of field including medical, chemical, marine, automotive, aerospace, aviation, electronic industries, nuclear reactor, consumer products etc., The conventional machining of Ti-6Al-4V is very difficult due to its distinctive properties. The Electrical Discharge Machining (EDM) is right choice of machining this material. The tungsten copper composite material is employed as tool material. The gap voltage, peak current, pulse on time and duty factor is considered as the machining parameter to analyze the machining characteristics Material Removal Rate (MRR) and Tool Wear Rate (TWR). The Taguchi method is provided to work for finding the significant parameter of EDM. It is found that for MRR significant parameters rated in the following order Gap Voltage, Pulse On-Time, Peak Current and Duty Factor. On the other hand for TWR significant parameters are listed in line of Gap Voltage, Duty Factor, Peak Current and Pulse On-Time.

Machine protection systems

CERN Document Server

Macpherson, A L

2010-01-01

A summary of the Machine Protection System of the LHC is given, with particular attention given to the outstanding issues to be addressed, rather than the successes of the machine protection system from the 2009 run. In particular, the issues of Safe Machine Parameter system, collimation and beam cleaning, the beam dump system and abort gap cleaning, injection and dump protection, and the overall machine protection program for the upcoming run are summarised.

Genetic restoration in the eastern collared lizard under prescribed woodland burning.

Science.gov (United States)

Neuwald, Jennifer L; Templeton, Alan R

2013-07-01

Eastern collared lizards of the Ozarks live in glades--open, rocky habitats embedded in a woodland matrix. Past fire suppression had made the woodlands a barrier to dispersal, leading to habitat destruction, fragmentation and local extinction. Reintroduced populations of lizards were subjected to 10 years of habitat fragmentation under continued fire suppression followed by twelve years of landscape restoration with prescribed burns. Prior to prescribed burning, genetic diversity decreased within glades and differentiation increased among glades. With woodland burning, genetic diversity within glades first decreased during an expanding colonization phase, but then increased as a dynamically stable metapopulation was established. Population differentiation among glades also stabilized in the metapopulation under weak isolation-by-distance. This study is one of the first to examine the genetic changes in a species of conservation concern throughout all the stages of decline and recovery and shows the importance of landscape-level restoration for maintaining the genetic integrity of populations. This study also demonstrates how mark-recapture and genetic data together can yield detailed insight into metapopulation dynamics that would be impossible from just one type of data alone. © 2013 John Wiley & Sons Ltd.

Preliminary Test of Upgraded Conventional Milling Machine into PC Based CNC Milling Machine

International Nuclear Information System (INIS)

Abdul Hafid

2008-01-01

CNC (Computerized Numerical Control) milling machine yields a challenge to make an innovation in the field of machining. With an action job is machining quality equivalent to CNC milling machine, the conventional milling machine ability was improved to be based on PC CNC milling machine. Mechanically and instrumentally change. As a control replacing was conducted by servo drive and proximity were used. Computer programme was constructed to give instruction into milling machine. The program structure of consists GUI model and ladder diagram. Program was put on programming systems called RTX software. The result of up-grade is computer programming and CNC instruction job. The result was beginning step and it will be continued in next time. With upgrading ability milling machine becomes user can be done safe and optimal from accident risk. By improving performance of milling machine, the user will be more working optimal and safely against accident risk. (author)

Re-establishing filtering capabilities of machined porous beryllium via chemical reduction and cleaning

International Nuclear Information System (INIS)

Randall, W.L.

1975-01-01

Porous beryllium is furnished in sheets of varying sizes and thickness; it is therefore necessary that it be machined into specified sizes. A chemical reduction and cleaning procedure was devised to remove the disrupted surface, open the sealed pores of the material, and clean entrapped contaminates from the internal structure. Dimensional stability can be closely controlled and material size is of no consequence. (U.S.)

Fine structure and development of the collar enamel in gars, Lepisosteus oculatus, Actinopterygii

Science.gov (United States)

Sasagawa, Ichiro; Ishiyama, Mikio; Yokosuka, Hiroyuki; Mikami, Masato

2008-06-01

The fine structure of collar enamel and the cells constituting the enamel organ during amelogenesis in Lepisosteus oculatus was observed by light, scanning electron and transmission electron microscopy. In the enamel, slender crystals were arranged perpendicular to the surface and the stripes that were parallel to the surface were observed, suggesting that the enamel in Lepisosteus shares common morphological features with that in sarcopterygian fish and amphibians. Ameloblasts containing developed Golgi apparatus, rough endoplasmic reticulum (rER) and secretory granules were found in the secretory stage. In the maturation stage, a ruffled border was not seen at the distal end of the ameloblasts, while many mitochondria and lysosome-like granules were obvious in the distal cytoplasm. The enamel organ consisted of the outer dental epithelial cells, stratum reticulum cells and ameloblasts, but there was no stratum intermedium. It is likely that the ameloblasts have less absorptive function in comparison with the inner dental epithelial cells facing cap enameloid.

Hematology values of captive giant anteaters (Myrmecophaga tridactyla and collared anteaters (Tamandua tetradactyla

Directory of Open Access Journals (Sweden)

Thaís C. Sanches

2013-04-01

Full Text Available Hematological results are reported for 13 giant anteaters (Myrmecophaga tridactyla and 13 collared anteaters (Tamandua tetradactyla. Animals were captive-reared adults held at the Fundação Parque Zoológico de São Paulo (São Paulo, SP, Brazil and Parque Zoológico Municipal Quinzinho de Barros (Sorocaba, SP, Brazil, and were considered healthy on physical examination. Examined parameters included red blood cell count, white blood cell count, hematocrit, hemoglobin concentration, mean corpuscular volume, mean corpuscular hemoglobin, mean corpuscular hemoglobin concentration, total plasmatic protein and differential leukocyte counts. Also, a survey for hemoparasites was done and none was observed in thin blood smears. The results were generally similar to those previously reported in the exiguous literature for these species, providing further reference data for the interpretation of laboratory results besides health monitoring, assisting early disease diagnosis and providing relevant information for conservation programs for these species.

Study of on-machine error identification and compensation methods for micro machine tools

International Nuclear Information System (INIS)

Wang, Shih-Ming; Yu, Han-Jen; Lee, Chun-Yi; Chiu, Hung-Sheng

2016-01-01

Micro machining plays an important role in the manufacturing of miniature products which are made of various materials with complex 3D shapes and tight machining tolerance. To further improve the accuracy of a micro machining process without increasing the manufacturing cost of a micro machine tool, an effective machining error measurement method and a software-based compensation method are essential. To avoid introducing additional errors caused by the re-installment of the workpiece, the measurement and compensation method should be on-machine conducted. In addition, because the contour of a miniature workpiece machined with a micro machining process is very tiny, the measurement method should be non-contact. By integrating the image re-constructive method, camera pixel correction, coordinate transformation, the error identification algorithm, and trajectory auto-correction method, a vision-based error measurement and compensation method that can on-machine inspect the micro machining errors and automatically generate an error-corrected numerical control (NC) program for error compensation was developed in this study. With the use of the Canny edge detection algorithm and camera pixel calibration, the edges of the contour of a machined workpiece were identified and used to re-construct the actual contour of the work piece. The actual contour was then mapped to the theoretical contour to identify the actual cutting points and compute the machining errors. With the use of a moving matching window and calculation of the similarity between the actual and theoretical contour, the errors between the actual cutting points and theoretical cutting points were calculated and used to correct the NC program. With the use of the error-corrected NC program, the accuracy of a micro machining process can be effectively improved. To prove the feasibility and effectiveness of the proposed methods, micro-milling experiments on a micro machine tool were conducted, and the results

National Machine Guarding Program: Part 1. Machine safeguarding practices in small metal fabrication businesses.

Science.gov (United States)

Parker, David L; Yamin, Samuel C; Brosseau, Lisa M; Xi, Min; Gordon, Robert; Most, Ivan G; Stanley, Rodney

2015-11-01

Metal fabrication workers experience high rates of traumatic occupational injuries. Machine operators in particular face high risks, often stemming from the absence or improper use of machine safeguarding or the failure to implement lockout procedures. The National Machine Guarding Program (NMGP) was a translational research initiative implemented in conjunction with two workers' compensation insures. Insurance safety consultants trained in machine guarding used standardized checklists to conduct a baseline inspection of machine-related hazards in 221 business. Safeguards at the point of operation were missing or inadequate on 33% of machines. Safeguards for other mechanical hazards were missing on 28% of machines. Older machines were both widely used and less likely than newer machines to be properly guarded. Lockout/tagout procedures were posted at only 9% of machine workstations. The NMGP demonstrates a need for improvement in many aspects of machine safety and lockout in small metal fabrication businesses. © 2015 The Authors. American Journal of Industrial Medicine published by Wiley Periodicals, Inc.

Non-conventional electrical machines

CERN Document Server

Rezzoug, Abderrezak

2013-01-01

The developments of electrical machines are due to the convergence of material progress, improved calculation tools, and new feeding sources. Among the many recent machines, the authors have chosen, in this first book, to relate the progress in slow speed machines, high speed machines, and superconducting machines. The first part of the book is dedicated to materials and an overview of magnetism, mechanic, and heat transfer.

Investigation of Carbon Fiber Reinforced Plastics Machining Using 355 nm Picosecond Pulsed Laser

Science.gov (United States)

Hu, Jun; Zhu, Dezhi

2018-06-01

Carbon fiber reinforced plastics (CFRP) has been widely used in the aircraft industry and automobile industry owing to its superior properties. In this paper, a Nd:YVO4 picosecond pulsed system emitting at 355 nm has been used for CFRP machining experiments to determine optimum milling conditions. Milling parameters including laser power, milling speed and hatch distance were optimized by using box-behnken design of response surface methodology (RSM). Material removal rate was influenced by laser beam overlap ratio which affects mechanical denudation. The results in heat affected zones (HAZ) and milling quality were discussed through the machined surface observed with scanning electron microscope. A re-focusing technique based on the experiment with different focal planes was proposed and milling mechanism was also analyzed in details.

Investigation of Carbon Fiber Reinforced Plastics Machining Using 355 nm Picosecond Pulsed Laser

Science.gov (United States)

Hu, Jun; Zhu, Dezhi

2017-08-01

Carbon fiber reinforced plastics (CFRP) has been widely used in the aircraft industry and automobile industry owing to its superior properties. In this paper, a Nd:YVO4 picosecond pulsed system emitting at 355 nm has been used for CFRP machining experiments to determine optimum milling conditions. Milling parameters including laser power, milling speed and hatch distance were optimized by using box-behnken design of response surface methodology (RSM). Material removal rate was influenced by laser beam overlap ratio which affects mechanical denudation. The results in heat affected zones (HAZ) and milling quality were discussed through the machined surface observed with scanning electron microscope. A re-focusing technique based on the experiment with different focal planes was proposed and milling mechanism was also analyzed in details.

From "Gut Feeling" to Objectivity: Machine Preservation of the Liver as a Tool to Assess Organ Viability.

Science.gov (United States)

Watson, Christopher J E; Jochmans, Ina

2018-01-01

The purpose of this review was to summarise how machine perfusion could contribute to viability assessment of donor livers. In both hypothermic and normothermic machine perfusion, perfusate transaminase measurement has allowed pretransplant assessment of hepatocellular damage. Hypothermic perfusion permits transplantation of marginal grafts but as yet has not permitted formal viability assessment. Livers undergoing normothermic perfusion have been investigated using parameters similar to those used to evaluate the liver in vivo. Lactate clearance, glucose evolution and pH regulation during normothermic perfusion seem promising measures of viability. In addition, bile chemistry might inform on cholangiocyte viability and the likelihood of post-transplant cholangiopathy. While the use of machine perfusion technology has the potential to reduce and even remove uncertainty regarding liver graft viability, analysis of large datasets, such as those derived from large multicenter trials of machine perfusion, are needed to provide sufficient information to enable viability parameters to be defined and validated .

Advanced Machine learning Algorithm Application for Rotating Machine Health Monitoring

Energy Technology Data Exchange (ETDEWEB)

Kanemoto, Shigeru; Watanabe, Masaya [The University of Aizu, Aizuwakamatsu (Japan); Yusa, Noritaka [Tohoku University, Sendai (Japan)

2014-08-15

The present paper tries to evaluate the applicability of conventional sound analysis techniques and modern machine learning algorithms to rotating machine health monitoring. These techniques include support vector machine, deep leaning neural network, etc. The inner ring defect and misalignment anomaly sound data measured by a rotating machine mockup test facility are used to verify the above various kinds of algorithms. Although we cannot find remarkable difference of anomaly discrimination performance, some methods give us the very interesting eigen patterns corresponding to normal and abnormal states. These results will be useful for future more sensitive and robust anomaly monitoring technology.

Advanced Machine learning Algorithm Application for Rotating Machine Health Monitoring

International Nuclear Information System (INIS)

Kanemoto, Shigeru; Watanabe, Masaya; Yusa, Noritaka

2014-01-01