Cold Vacuum Drying Safety Class Instrumentation and Control System Design Description

International Nuclear Information System (INIS)

WHITEHURST, R.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) Safety Class Instrumentation and Control system (SCIC). The SCIC provides safety functions and features to protect the environment, off-site and on-site personnel and equipment. The function of the SCIC is to provide automatic trip features, valve interlocks, alarms, indication and control for the cold vacuum drying process

DEVELOPMENT OF VACUUM SUBLIMATION DRYERS USING THERMOELECTRIC MODULES

Directory of Open Access Journals (Sweden)

R. A. Barykin

2014-01-01

Full Text Available Summary. The main directions of use of freeze-dryed products and ingredients are revealed. The analysis of sales markets of freeze-dryed products is provided. It is shown that introduction of innovative production technologies will allow to develop dynamically not only to the large companies, but also small firms that will create prerequisites for growth of the Russian market of freeze-dryed products. Tendencies of development of the freeze-drying equipment are analysed. Relevance of development of energy saving freeze-dryers is proved The integrated approach to creation of competitive domestic technologies and the equipment for sublimation dehydration of thermolabile products consists in use of the effective combined remedies of a power supply, a process intensification, reduction of specific energy consumption and, as a result, decrease in product cost at achievement of high quality indicators. Advantages of thermoelectric modules as alternative direction to existing vapor-compression and absorbing refrigerating appliances are given. Researches of process of freeze-drying dehydration with use of thermoelectric modules are conducted. It is scientifically confirmed, that the thermoelectric module working at Peltier effect, promotes increase in refrigerating capacity due to use of the principle of the thermal pump. Options of use of thermoelectric modules in designs of dryers are offered. Optimum operating modes and number of modules in section are defined. Ways of increase of power efficiency of freeze-dryers with use of thermoelectric modules are specified. The received results will allow to make engineering calculations and design of progressive freeze-drying installations with various ways of a power supply.

Cold Vacuum Drying facility design basis accident analysis documentation

International Nuclear Information System (INIS)

CROWE, R.D.

2000-01-01

This document provides the detailed accident analysis to support HNF-3553, Annex B, Spent Nuclear Fuel Project Final Safety Analysis Report (FSAR), ''Cold Vacuum Drying Facility Final Safety Analysis Report.'' All assumptions, parameters, and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the FSAR. The calculations in this document address the design basis accidents (DBAs) selected for analysis in HNF-3553, ''Spent Nuclear Fuel Project Final Safety Analysis Report'', Annex B, ''Cold Vacuum Drying Facility Final Safety Analysis Report.'' The objective is to determine the quantity of radioactive particulate available for release at any point during processing at the Cold Vacuum Drying Facility (CVDF) and to use that quantity to determine the amount of radioactive material released during the DBAs. The radioactive material released is used to determine dose consequences to receptors at four locations, and the dose consequences are compared with the appropriate evaluation guidelines and release limits to ascertain the need for preventive and mitigative controls

Cold Vacuum Drying facility design basis accident analysis documentation

Energy Technology Data Exchange (ETDEWEB)

CROWE, R.D.

2000-08-08

This document provides the detailed accident analysis to support HNF-3553, Annex B, Spent Nuclear Fuel Project Final Safety Analysis Report (FSAR), ''Cold Vacuum Drying Facility Final Safety Analysis Report.'' All assumptions, parameters, and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the FSAR. The calculations in this document address the design basis accidents (DBAs) selected for analysis in HNF-3553, ''Spent Nuclear Fuel Project Final Safety Analysis Report'', Annex B, ''Cold Vacuum Drying Facility Final Safety Analysis Report.'' The objective is to determine the quantity of radioactive particulate available for release at any point during processing at the Cold Vacuum Drying Facility (CVDF) and to use that quantity to determine the amount of radioactive material released during the DBAs. The radioactive material released is used to determine dose consequences to receptors at four locations, and the dose consequences are compared with the appropriate evaluation guidelines and release limits to ascertain the need for preventive and mitigative controls.

Spent Nuclear Fuel (SNF) Cold Vacuum Drying (CVD) Facility Operations Manual

Energy Technology Data Exchange (ETDEWEB)

IRWIN, J.J.

1999-07-02

This document provides the Operations Manual for the Cold Vacuum Drying Facility (CVDF). The Manual was developed in conjunction with HNF-553, Spent Nuclear Fuel Project Final Safety Analysis Report Annex B--Cold Vacuum Drying Facility. The HNF-SD-SNF-DRD-002, 1999, Cold Vacuum Drying Facility Design Requirements, Rev. 4, and the CVDF Final Design Report. The Operations Manual contains general descriptions of all the process, safety and facility systems in the CVDF, a general CVD operations sequence and references to the CVDF System Design Descriptions (SDDs). This manual has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

COLDDIAG: A Cold Vacuum Chamber for Diagnostics

CERN Document Server

Casalbuoni, S; Gerstl, S; Grau, A W; Hagelstein, M; Saez de Jauregui, D; Boffo, C; Sikler, G; Baglin, V; Cox, M P; Schouten, J C; Cimino, R; Commisso, M; Spataro, B; Mostacci, A; Wallen, E J; Weigel, R; Clarke, J; Scott, D; Bradshaw, T; Jones, R; Shinton, I

2011-01-01

One of the still open issues for the development of superconducting insertion devices is the understanding of the beam heat load. With the aim of measuring the beam heat load to a cold bore and the hope to gain a deeper understanding in the beam heat load mechanisms, a cold vacuum chamber for diagnostics is under construction. The following diagnostics will be implemented: i) retarding field analyzers to measure the electron energy and flux, ii) temperature sensors to measure the total heat load, iii) pressure gauges, iv) and mass spectrometers to measure the gas content. The inner vacuum chamber will be removable in order to test different geometries and materials. This will allow the installation of the cryostat in different synchrotron light sources. COLDDIAG will be built to fit in a short straight section at ANKA. A first installation at the synchrotron light source Diamond is foreseen in June 2011. Here we describe the technical design report of this device and the planned measurements with beam.

Spent Nuclear Fuel (SNF) Project Cold Vacuum Drying (CVD) Facility Operations Manual

Energy Technology Data Exchange (ETDEWEB)

IRWIN, J.J.

2000-02-03

This document provides the Operations Manual for the Cold Vacuum Drying Facility (CVDF). The Manual was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of the Processing Systems (Garvin 1998) and, the HNF-SD-SNF-DRD-002, 1997, Cold Vacuum Drying Facility Design Requirements, Rev. 3a. The Operations Manual contains general descriptions of all the process, safety and facility systems in the CVDF, a general CVD operations sequence, and has been developed for the spent nuclear fuel project (SNFP) Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

Spent Nuclear Fuel (SNF) Cold Vacuum Drying (CVD) Facility Operations Manual; FINAL

International Nuclear Information System (INIS)

IRWIN, J.J.

1999-01-01

This document provides the Operations Manual for the Cold Vacuum Drying Facility (CVDF). The Manual was developed in conjunction with HNF-553, Spent Nuclear Fuel Project Final Safety Analysis Report Annex B-Cold Vacuum Drying Facility. The HNF-SD-SNF-DRD-002, 1999, Cold Vacuum Drying Facility Design Requirements, Rev. 4, and the CVDF Final Design Report. The Operations Manual contains general descriptions of all the process, safety and facility systems in the CVDF, a general CVD operations sequence and references to the CVDF System Design Descriptions (SDDs). This manual has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Spent Nuclear Fuel (SNF) Project Cold Vacuum Drying (CVD) Facility Operations Manual

International Nuclear Information System (INIS)

IRWIN, J.J.

2000-01-01

This document provides the Operations Manual for the Cold Vacuum Drying Facility (CVDF). The Manual was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of the Processing Systems (Garvin 1998) and, the HNF-SD-SNF-DRD-002, 1997, Cold Vacuum Drying Facility Design Requirements, Rev. 3a. The Operations Manual contains general descriptions of all the process, safety and facility systems in the CVDF, a general CVD operations sequence, and has been developed for the spent nuclear fuel project (SNFP) Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Cold Vacuum Drying (CVD) Facility, Diesel Generator Fire Protection

CERN Document Server

Singh, G

2000-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Fire Protection and Detection System installed by Project W-441 (Cold Vacuum Drying Facility and Diesel Generator Building) functions as required by project specifications.

Cold Vacuum Drying (CVD) Facility, Diesel Generator Fire Protection

International Nuclear Information System (INIS)

SINGH, G.

2000-01-01

This Acceptance Test Procedure (ATP) has been prepared to demonstrate that the Fire Protection and Detection System installed by Project W-441 (Cold Vacuum Drying Facility and Diesel Generator Building) functions as required by project specifications

Spent nuclear fuel project cold vacuum drying facility supporting data and calculation database

International Nuclear Information System (INIS)

IRWIN, J.J.

1999-01-01

This document provides a database of supporting calculations for the Cold Vacuum Drying Facility (CVDF). The database was developed in conjunction with HNF-SD-SNF-SAR-002, ''Safety Analysis Report for the Cold Vacuum Drying Facility'', Phase 2, ''Supporting Installation of Processing Systems'' (Garvin 1998). The HNF-SD-SNF-DRD-002, 1997, ''Cold Vacuum Drying Facility Design Requirements'', Rev. 2, and the CVDF Summary Design Report. The database contains calculation report entries for all process, safety and facility systems in the CVDF, a general CVD operations sequence and the CVDF System Design Descriptions (SDDs). This database has been developed for the SNFP CVDF Engineering Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Cold Vacuum Drying Safety Class Instrumentation and Control System Design Description SYS 93-2

International Nuclear Information System (INIS)

WHITEHURST, R.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) Safety Class Instrumentation and Control system (SCIC). The SCIC provides safety functions and features to protect the environment, off-site and on-site personnel and equipment. The function of the SCIC is to provide automatic trip features, valve interlocks, alarms, indication and control for the cold vacuum drying process

Spent nuclear fuel project cold vacuum drying facility supporting data and calculation database

Energy Technology Data Exchange (ETDEWEB)

IRWIN, J.J.

1999-02-26

This document provides a database of supporting calculations for the Cold Vacuum Drying Facility (CVDF). The database was developed in conjunction with HNF-SD-SNF-SAR-002, ''Safety Analysis Report for the Cold Vacuum Drying Facility'', Phase 2, ''Supporting Installation of Processing Systems'' (Garvin 1998). The HNF-SD-SNF-DRD-002, 1997, ''Cold Vacuum Drying Facility Design Requirements'', Rev. 2, and the CVDF Summary Design Report. The database contains calculation report entries for all process, safety and facility systems in the CVDF, a general CVD operations sequence and the CVDF System Design Descriptions (SDDs). This database has been developed for the SNFP CVDF Engineering Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved.

Spent nuclear fuel project cold vacuum drying facility process water conditioning system design description

International Nuclear Information System (INIS)

IRWIN, J.J.

1998-01-01

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Process Water Conditioning (PWC) System. The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), the HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the PWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Cold Vacuum Drying Facility hazard analysis report

Energy Technology Data Exchange (ETDEWEB)

Krahn, D.E.

1998-02-23

This report describes the methodology used in conducting the Cold Vacuum Drying Facility (CVDF) hazard analysis to support the CVDF phase 2 safety analysis report (SAR), and documents the results. The hazard analysis was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, and implements the requirements of US Department of Energy (DOE) Order 5480.23, Nuclear Safety Analysis Reports.

Cold Vacuum Drying Facility hazard analysis report

International Nuclear Information System (INIS)

Krahn, D.E.

1998-01-01

This report describes the methodology used in conducting the Cold Vacuum Drying Facility (CVDF) hazard analysis to support the CVDF phase 2 safety analysis report (SAR), and documents the results. The hazard analysis was performed in accordance with DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, and implements the requirements of US Department of Energy (DOE) Order 5480.23, Nuclear Safety Analysis Reports

Status of COLDDIAG: A Cold Vacuum Chamber for Diagnostics

CERN Document Server

Gerstl, Stefan; Casalbuoni, Sara; Grau, Andreas; Hagelstein, Michael; Saez de Jauregui, David; Baglin, Vincent; Boffo, Cristian; Sikler, Gunther; Bradshaw, Thomas; Cimino, Roberto; Commisso, Mario; Spataro, Bruno; Clarke, James; Scott, Duncan; Cox, Matthew; Schouten, Jos; Jones, Roger; Shinton, Ian; Mostacci, Andrea; Wallen, Erik; Weigel, Ralf

2010-01-01

One of the still open issues for the development of superconducting insertion devices is the understanding of the beam heat load. With the aim of measuring the beam heat load to a cold bore and the hope to gain a deeper understanding in the beam heat load mechanisms, a cold vacuum chamber for diagnostics is under construction. The following diagnostics will be implemented: i) retarding field analyzers to measure the electron energy and flux, ii) temperature sensors to measure the total heat load, iii) pressure gauges, iv) and mass spectrometers to measure the gas content. The inner vacuum chamber will be removable in order to test different geometries and materials. This will allow the installation of the cryostat in different synchrotron light sources. COLDDIAG will be built to fit in a short straight section at ANKA. A first installation at the synchrotron light source Diamond is foreseen in June 2011. Here we describe the technical design report of this device and the planned measurements with beam.

Cold Vacuum Drying (CVD) OCRWM Loop Error Determination

International Nuclear Information System (INIS)

PHILIPP, B.L.

2000-01-01

Characterization is specifically identified by the Richland Operations Office (RL) for the Office of Civilian Radioactive Waste Management (OCRWM) of the US Department of Energy (DOE), as requiring application of the requirements in the Quality Assurance Requirements and Description (QARD) (RW-0333P DOE 1997a). Those analyses that provide information that is necessary for repository acceptance require application of the QARD. The cold vacuum drying (CVD) project identified the loops that measure, display, and record multi-canister overpack (MCO) vacuum pressure and Tempered Water (TW) temperature data as providing OCRWM data per Application of the Office of Civilian Radioactive Waste Management (OCRWM) Quality Assurance Requirements to the Hanford Spent Nuclear Fuel Project HNF-SD-SNF-RPT-007. Vacuum pressure transmitters (PT 1*08, 1*10) and TW temperature transmitters (TIT-3*05, 3*12) are used to verify drying and to determine the water content within the MCO after CVD

Spent Nuclear Fuel Cold Vacuum Drying facility comprehensive formal design review report

International Nuclear Information System (INIS)

HALLER, C.S.

1999-01-01

The majority of the Cold Vacuum Drying Facility (CVDF) design and construction is complete; isolated portions are still in the design and fabrication process. The project commissioned a formal design review to verify the sufficiency and accuracy of current design media to assure that: (1) the design completely and accurately reflects design criteria, (2) design documents are consistent with one another, and (3) the design media accurately reflects the current design. This review is a key element in the design validation and verification activities required by SNF-4396, ''Design Verification and Validation Plan For The Cold Vacuum Drying Facility''. This report documents the results of the formal design review

Cold Vacuum Drying (CVD) Electrical System Design Description

International Nuclear Information System (INIS)

BRISBIN, S.A.

1999-01-01

This document provides a technical explanation of the design and operation of the electrical system for the Cold Vacuum Drying Facility. This document identifies the requirements, and the basis for the requirements and details on how the requirements have been implemented in the design and construction of the facility. This document also provides general guidance for the surveillance, testing, and maintenance of this system

Cold Vacuum Drying Facility Design Basis Accident Analysis Documentation

International Nuclear Information System (INIS)

PIEPHO, M.G.

1999-01-01

This document provides the detailed accident analysis to support HNF-3553, Annex B, Spent Nuclear Fuel Project Final Safety Analysis Report, ''Cold Vacuum Drying Facility Final Safety Analysis Report (FSAR).'' All assumptions, parameters and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the FSAR

Cold Vacuum Drying facility condensate collection system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) condensate collection system (CCS). The function of the CCS is to collect cooling coil condensate from air-handling units in the CVDF and to isolate the condensate in collection tanks until the condensate is determined to be acceptable to drain to the effluent drain collection basin

Cold Vacuum Drying facility potable water system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) potable water (PW) system. The PW system provides potable water to the CVDF for supply to sinks, water closets, urinals, showers, custodial service sinks, drinking fountains, the decontamination shower, supply water to the non-PW systems, and makeup water for the de-ionized water system

Cold Vacuum Drying (CVD) Electrical System Design Description

International Nuclear Information System (INIS)

SINGH, G.

2000-01-01

This system design description (SDD) provides a technical explanation of the design and operation of the electrical system for the Cold Vacuum Drying Facility (CVDF). This SDD also identifies the requirements, and the basis for the requirements and details on how the requirements have been implemented in the design and construction of the facility. This SDD also provides general guidance for the surveillance, testing, and maintenance of this system

System Configuration Management Implementation Procedure for the Cold Vacuum Drying Facility Monitoring and Control System

International Nuclear Information System (INIS)

ANGLESEY, M.O.

2000-01-01

The purpose of this document is to establish the System Configuration Management Implementation Procedure (SCMIP) for the Cold Vacuum Drying Facility (CVDF) Monitoring and Control System (MCS). This procedure provides configuration management for the process control system. The process control system consists of equipment hardware and software that controls and monitors the instrumentation and equipment associated with the CVDF processes. Refer to SNF-3090, Cold Vacuum Drying Facility Monitoring and Control System Design Description, HNF-3553, Annex B, Safety Analysis Report for the Cold Vacuum Drying Facility, and AP-CM-6-037-00, SNF Project Process Automation Software and Equipment Configuration. This SCMIP identifies and defines the system configuration items in the control system, provides configuration control throughout the system life cycle, provides configuration status accounting, physical protection and control, and verifies the completeness and correctness of these items

Fire Hazard Analysis for the Cold Vacuum Drying (CVD) Facility

Energy Technology Data Exchange (ETDEWEB)

JOHNSON, B.H.

1999-08-19

This Fire Hazard Analysis assesses the risk from fire within individual fire areas in the Cold Vacuum Drying Facility at the Hanford Site in relation to existing or proposed fire protection features to ascertain whether the objectives of DOE Order 5480.7A Fire Protection are met.

Fire Hazard Analysis for the Cold Vacuum Drying (CVD) Facility

International Nuclear Information System (INIS)

JOHNSON, B.H.

1999-01-01

This Fire Hazard Analysis assesses the risk from fire within individual fire areas in the Cold Vacuum Drying Facility at the Hanford Site in relation to existing or proposed fire protection features to ascertain whether the objectives of DOE Order 5480.7A Fire Protection are met

Design verification and validation plan for the cold vacuum drying facility

International Nuclear Information System (INIS)

NISHIKAWA, L.D.

1999-01-01

The Cold Vacuum Drying Facility (CVDF) provides the required process systems, supporting equipment, and facilities needed for drying spent nuclear fuel removed from the K Basins. This document presents the both completed and planned design verification and validation activities

Spent Nuclear Fuel (SNF) Project Cold Vacuum Drying (CVD) Facility Operations Manual

International Nuclear Information System (INIS)

IRWIN, J.J.

2000-01-01

The mission of the Spent Nuclear Fuel (SNF) Project Cold Vacuum Drying Facility (CVDF) is to achieve the earliest possible removal of free water from Multi-Canister Overpacks (MCOs). The MCOs contain metallic uranium SNF that have been removed from the 100K Area fuel storage water basins (i.e., the K East and K West Basins) at the US. Department of Energy Hanford Site in Southeastern Washington state. Removal of free water is necessary to halt water-induced corrosion of exposed uranium surfaces and to allow the MCOs and their SNF payloads to be safely transported to the Hanford Site 200 East Area and stored within the SNF Project Canister Storage Building (CSB). The CVDF is located within a few hundred yards of the basins, southwest of the 165KW Power Control Building and the 105KW Reactor Building. The site area required for the facility and vehicle circulation is approximately 2 acres. Access and egress is provided by the main entrance to the 100K inner area using existing roadways. The CVDF will remove free. water from the MCOs to reduce the potential for continued fuel-water corrosion reactions. The cold vacuum drying process involves the draining of bulk water from the MCO and subsequent vacuum drying. The MCO will be evacuated to a pressure of 8 torr or less and backfilled with an inert gas (helium). The MCO will be sealed, leak tested, and then transported to the CSB within a sealed shipping cask. (The MCO remains within the same shipping Cask from the time it enters the basin to receive its SNF payload until it is removed from the Cask by the CSB MCO handling machine.) The CVDF subproject acquired the required process systems, supporting equipment, and facilities. The cold vacuum drying operations result in an MCO containing dried fuel that is prepared for shipment to the CSB by the Cask transportation system. The CVDF subproject also provides equipment to dispose of solid wastes generated by the cold vacuum drying process and transfer process water removed

Cold Vacuum Drying facility fire protection system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) fire protection system (FPS). The FPS provides fire detection, suppression, and loss limitation for the CVDF structure, personnel, and in-process spent nuclear fuel. The system provides, along with supporting interfacing systems, detection, alarm, and activation instrumentation and controls, distributive piping system, isolation valves, and materials and controls to limit combustibles and the associated fire loadings

Cold Vacuum Drying (CVD) Facility Design Basis Accident Analysis Documentation

Energy Technology Data Exchange (ETDEWEB)

PIEPHO, M.G.

1999-10-20

This document provides the detailed accident analysis to support HNF-3553, Annex B, Spent Nuclear Fuel Project Final Safety Analysis Report, ''Cold Vacuum Drying Facility Final Safety Analysis Report (FSAR).'' All assumptions, parameters and models used to provide the analysis of the design basis accidents are documented to support the conclusions in the FSAR.

Spent nuclear fuel project cold vacuum drying facility safety equipment list

International Nuclear Information System (INIS)

IRWIN, J.J.

1999-01-01

This document provides the safety equipment list (SEL) for the Cold Vacuum Drying Facility (CVDF). The SEL was prepared in accordance with the procedure for safety structures, systems, and components (SSCs) in HNF-PRO-516, ''Safety Structures, Systems, and Components,'' Revision 0 and HNF-PRO-097, Engineering Design and Evaluation, Revision 0. The SEL was developed in conjunction with HNF-SO-SNF-SAR-O02, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998). The SEL identifies the SSCs and their safety functions, the design basis accidents for which they are required to perform, the design criteria, codes and standards, and quality assurance requirements that are required for establishing the safety design basis of the SSCs. This SEL has been developed for the CVDF Phase 2 Safety Analysis Report (SAR) and shall be updated, expanded, and revised in accordance with future phases of the CVDF SAR until the CVDF final SAR is approved

Cold vacuum chamber for diagnostics: Instrumentation and first results

Directory of Open Access Journals (Sweden)

S. Gerstl

2014-10-01

Full Text Available For a proper design of the cryogenic layout of superconducting insertion devices it is necessary to take into account the heat load from the beam to the cold beam tube. In order to measure and possibly understand the beam heat load to a cold bore, a cold vacuum chamber for diagnostics (COLDDIAG has been built. COLDDIAG is designed in a flexible way, to allow its installation in different light sources. In order to study the beam heat load and the influence of the cryosorbed gas layer, the instrumentation comprises temperature sensors, pressure gauges, and mass spectrometers as well as retarding field analyzers with which it is possible to measure the beam heat load, total pressure, and gas content as well as the flux of particles hitting the chamber walls. In this paper we describe the experimental equipment, the installation of COLDDIAG in the Diamond Light Source and selected examples of the measurements performed to show the capabilities of this unique instrument.

Cold vacuum chamber for diagnostics: Instrumentation and first results

Science.gov (United States)

Gerstl, S.; Voutta, R.; Casalbuoni, S.; Grau, A. W.; Holubek, T.; de Jauregui, D. Saez; Bartolini, R.; Cox, M. P.; Longhi, E. C.; Rehm, G.; Schouten, J. C.; Walker, R. P.; Sikler, G.; Migliorati, M.; Spataro, B.

2014-10-01

For a proper design of the cryogenic layout of superconducting insertion devices it is necessary to take into account the heat load from the beam to the cold beam tube. In order to measure and possibly understand the beam heat load to a cold bore, a cold vacuum chamber for diagnostics (COLDDIAG) has been built. COLDDIAG is designed in a flexible way, to allow its installation in different light sources. In order to study the beam heat load and the influence of the cryosorbed gas layer, the instrumentation comprises temperature sensors, pressure gauges, and mass spectrometers as well as retarding field analyzers with which it is possible to measure the beam heat load, total pressure, and gas content as well as the flux of particles hitting the chamber walls. In this paper we describe the experimental equipment, the installation of COLDDIAG in the Diamond Light Source and selected examples of the measurements performed to show the capabilities of this unique instrument.

Cold Vacuum Drying facility effluent drain system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) effluent drain system (EFS). The primary function of the EFS is to collect and transport fire suppression water discharged into a CVDF process bay to a retention basin located outside the facility. The EFS also provides confinement of spills that occur inside a process bay and allows non-contaminated water that drains to the process bay sumps to be collected until sampling and analysis are complete

Cold Vacuum Drying facility deionized water system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) de-ionized water system. The de-ionized water system is used to provide clean, conditioned water, free from contaminants, chlorides and iron for the CVD Facility. Potable water is supplied to the deionized water system, isolated by a backflow prevention device. After the de-ionization process is complete, via a packaged de-ionization unit, de-ionized water is supplied to the process deionization unit

Spent nuclear fuel project cold vacuum drying facility tempered water and tempered water cooling system design description

International Nuclear Information System (INIS)

IRWIN, J.J.

1998-01-01

This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Tempered Water (TW) and Tempered Water Cooling (TWC) System . The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), The HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the TW and TWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SOD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E. [IVO International Oy, Vantaa (Finland)

1995-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E [IVO International Oy, Vantaa (Finland)

1996-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

Hanford spent nuclear fuel cold vacuum drying proof of performance test procedure

International Nuclear Information System (INIS)

McCracken, K.J.

1998-01-01

This document provides the test procedure for cold testing of the first article skids for the Cold Vacuum Drying (CVD) process at the Facility. The primary objective of this testing is to confirm design choices and provide data for the initial start-up parameters for the process. The current scope of testing in this document includes design verification, drying cycle determination equipment performance testing of the CVD process and MCC components, heat up and cool-down cycle determination, and thermal model validation

Gas Composition Transients in the Cold Vacuum Drying (CVD) Facility

International Nuclear Information System (INIS)

PACKER, M.J.

2000-01-01

The purpose of this document is to evaluate selected problems involving the prediction of transient gas compositions during Cold Vacuum Drying operations. The problems were evaluated to answer specific design questions. The document is formatted as a topical report with each section representing a specific problem solution. The problem solutions are reported in the calculation format specified in HNF-1613, Rev. 0, EP 7.6

Human factors engineering report for the cold vacuum drying facility

Energy Technology Data Exchange (ETDEWEB)

IMKER, F.W.

1999-06-30

The purpose of this report is to present the results and findings of the final Human Factors Engineering (HFE) technical analysis and evaluation of the Cold Vacuum Drying Facility (CVDF). Ergonomics issues are also addressed in this report, as appropriate. This report follows up and completes the preliminary work accomplished and reported by the Preliminary HFE Analysis report (SNF-2825, Spent Nuclear Fuel Project Cold Vacuum Drying Facility Human Factors Engineering Analysis: Results and Findings). This analysis avoids redundancy of effort except for ensuring that previously recommended HFE design changes have not affected other parts of the system. Changes in one part of the system may affect other parts of the system where those changes were not applied. The final HFE analysis and evaluation of the CVDF human-machine interactions (HMI) was expanded to include: the physical work environment, human-computer interface (HCI) including workstation and software, operator tasks, tools, maintainability, communications, staffing, training, and the overall ability of humans to accomplish their responsibilities, as appropriate. Key focal areas for this report are the process bay operations, process water conditioning (PWC) skid, tank room, and Central Control Room operations. These key areas contain the system safety-class components and are the foundation for the human factors design basis of the CVDF.

Human factors engineering report for the cold vacuum drying facility

International Nuclear Information System (INIS)

IMKER, F.W.

1999-01-01

The purpose of this report is to present the results and findings of the final Human Factors Engineering (HFE) technical analysis and evaluation of the Cold Vacuum Drying Facility (CVDF). Ergonomics issues are also addressed in this report, as appropriate. This report follows up and completes the preliminary work accomplished and reported by the Preliminary HFE Analysis report (SNF-2825, Spent Nuclear Fuel Project Cold Vacuum Drying Facility Human Factors Engineering Analysis: Results and Findings). This analysis avoids redundancy of effort except for ensuring that previously recommended HFE design changes have not affected other parts of the system. Changes in one part of the system may affect other parts of the system where those changes were not applied. The final HFE analysis and evaluation of the CVDF human-machine interactions (HMI) was expanded to include: the physical work environment, human-computer interface (HCI) including workstation and software, operator tasks, tools, maintainability, communications, staffing, training, and the overall ability of humans to accomplish their responsibilities, as appropriate. Key focal areas for this report are the process bay operations, process water conditioning (PWC) skid, tank room, and Central Control Room operations. These key areas contain the system safety-class components and are the foundation for the human factors design basis of the CVDF

Quantitative real-time monitoring of dryer effluent using fiber optic near-infrared spectroscopy.

Science.gov (United States)

Harris, S C; Walker, D S

2000-09-01

This paper describes a method for real-time quantitation of the solvents evaporating from a dryer. The vapor stream in the vacuum line of a dryer was monitored in real time using a fiber optic-coupled acousto-optic tunable filter near-infrared (AOTF-NIR) spectrometer. A balance was placed in the dryer, and mass readings were recorded for every scan of the AOTF-NIR. A partial least-squares (PLS) calibration was subsequently built based on change in mass over change in time for solvents typically used in a chemical manufacturing plant. Controlling software for the AOTF-NIR was developed. The software collects spectra, builds the PLS calibration model, and continuously fits subsequently collected spectra to the calibration, allowing the operator to follow the mass loss of solvent from the dryer. The results indicate that solvent loss can be monitored and quantitated in real time using NIR for the optimization of drying times. These time-based mass loss values have also been used to calculate "dynamic" vapor density values for the solvents. The values calculated are in agreement with values determined from the ideal gas law and could prove valuable as tools to measure temperature or pressure indirectly.

Criticality safety evaluation report for the cold vacuum drying facility's process water handling system

International Nuclear Information System (INIS)

NELSON, J.V.

1999-01-01

This report addresses the criticality concerns associated with process water handling in the Cold Vacuum Drying Facility. The controls and limitations on equipment design and operations to control potential criticality occurrences are identified

Cold Vacuum Drying facility crane and hoist system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) crane and hoist system. The overhead crane and hoist system is located in the process bays of the CVDF. It supports the processes required to drain the water and dry the spent nuclear fuel contained in the multi-canister overpacks after they have been removed from the K-Basins. The cranes will also be used to assist maintenance activities within the bays, as required

Additive manufacturing of magnetic shielding and ultra-high vacuum flange for cold atom sensors.

Science.gov (United States)

Vovrosh, Jamie; Voulazeris, Georgios; Petrov, Plamen G; Zou, Ji; Gaber, Youssef; Benn, Laura; Woolger, David; Attallah, Moataz M; Boyer, Vincent; Bongs, Kai; Holynski, Michael

2018-01-31

Recent advances in the understanding and control of quantum technologies, such as those based on cold atoms, have resulted in devices with extraordinary metrological performance. To realise this potential outside of a lab environment the size, weight and power consumption need to be reduced. Here we demonstrate the use of laser powder bed fusion, an additive manufacturing technique, as a production technique relevant to the manufacture of quantum sensors. As a demonstration we have constructed two key components using additive manufacturing, namely magnetic shielding and vacuum chambers. The initial prototypes for magnetic shields show shielding factors within a factor of 3 of conventional approaches. The vacuum demonstrator device shows that 3D-printed titanium structures are suitable for use as vacuum chambers, with the test system reaching base pressures of 5 ± 0.5 × 10 -10 mbar. These demonstrations show considerable promise for the use of additive manufacturing for cold atom based quantum technologies, in future enabling improved integrated structures, allowing for the reduction in size, weight and assembly complexity.

Observation of modified radiative properties of cold atoms in vacuum near a dielectric surface

International Nuclear Information System (INIS)

Ivanov, V V; Cornelussen, R A; Heuvell, H B van Linden van den; Spreeuw, R J C

2004-01-01

We have observed a distance-dependent absorption linewidth of cold 87 Rb atoms close to a dielectric-vacuum interface. This is the first observation of modified radiative properties in vacuum near a dielectric surface. A cloud of cold atoms was created using a magneto-optical trap (MOT) and optical molasses cooling. Evanescent waves (EW) were used to observe the behaviour of the atoms near the surface. We observed an increase of the absorption linewidth by up to 25% with respect to the free-space value. Approximately half the broadening can be explained by cavity quantum electrodynamics (CQED) as an increase of the natural linewidth and inhomogeneous broadening. The remainder we attribute to local Stark shifts near the surface. By varying the characteristic EW length we have observed a distance dependence characteristic for CQED

Cold vacuum drying residual free water test description

International Nuclear Information System (INIS)

Pajunen, A.L.

1997-01-01

Residual free water expected to remain in a Multi-Canister Overpack (MCO) after processing in the Cold Vacuum Drying (CVD) Facility is investigated based on three alternative models of fuel crevices. Tests and operating conditions for the CVD process are defined based on the analysis of these models. The models consider water pockets constrained by cladding defects, water constrained in a pore or crack by flow through a porous bed, and water constrained in pores by diffusion. An analysis of comparative reaction rate constraints is also presented indicating that a pressure rise test can be used to show MCO's will be thermally stable at operating temperatures up to 75 C

Cold Vacuum Drying facility condensate collection system design description (SYS 19); FINAL

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) condensate collection system (CCS). The function of the CCS is to collect cooling coil condensate from air-handling units in the CVDF and to isolate the condensate in collection tanks until the condensate is determined to be acceptable to drain to the effluent drain collection basin

THE NATURAL COLD ACCUMULATOR AND VACUUM INSTALLATION FOR MILK COOLING IN REPUBLIC OF MOLDOVA

Directory of Open Access Journals (Sweden)

Cretu V.

2010-04-01

Full Text Available Based on theoretical and experimental research of the milk cooling process was elaborated mathematical model of accumulator with natural cold and vacuum installations, which allows determining the operating system installations, mentioned from environmental parameters.

Test of solar dryers in Ghana

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S. [Teknologisk Institut. SolEnergiCentret, Taastrup (Denmark); Floejgaard Kristensen, E. [Danmarks JordbrugsForskning, Tjele (Denmark); Agyei, F. [FAGOD Ltd. (Ghana); Larsen, T. [Clipper Design Ltd. (Ghana); Nketiah, K.S. [FORIG (Ghana)

2002-06-01

The report describes the tests carried out in Ghana on three solar dryers as part of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat' financed by DANIDA. The main objective of the project was to develop and test solar dryers for crop, fish and wood in Ghana. Three dryers were erected: 1. Solar crop dryer: The solar crop dryer was erected at Silwood Farms at Pokuase about 30 km north of Accra. Silwood Farms grows primarily maize for seed and pineapples, 2. Solar fish dryer: The solar fish dryer was erected at Elite Enterprise Ltd. at Tema about 35 km east-north-east of Accra. Elite Enterprise Ltd. buys and dries fish, 3. Solar wood dryer: The solar wood dryers were erected at Clipper Design Ltd. at Mankoadze about 65 km west-south-west of Accra. Clipper Design Ltd. produces mainly doors. (BA)

Criticality Safety Evaluation Report for the Cold Vacuum Drying (CVD) Facility's Process Water Handling System

International Nuclear Information System (INIS)

KESSLER, S.F.

2000-01-01

This report addresses the criticality concerns associated with process water handling in the Cold Vacuum Drying Facility. The controls and limitations on equipment design and operations to control potential criticality occurrences are identified

Thermal analysis of cold vacuum drying of spent nuclear fuel

Energy Technology Data Exchange (ETDEWEB)

Piepho, M.G.

1998-07-20

The thermal analysis examined transient thermal and chemical behavior of the Multi canister Overpack (MCO) container for a broad range of cases that represent the Cold Vacuum Drying (CVD) processes. The cases were defined to consider both normal and off-normal operations at the CVD Facility for an MCO with Mark IV N, Reactor spent fuel in four fuel baskets and one scrap basket. This analysis provides the basis for the MCO thermal behavior at the CVD Facility for its Phase 2 Safety Analysis Report (revision 4).

Cold Vacuum Drying facility civil - structural system design description (SYS 06)

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying (CVD) Facility civil - structural system. This system consists of the facility structure, including the administrative and process areas. The system's primary purpose is to provide for a facility to house the CVD process and personnel and to provide a tertiary level of containment. The document provides a description of the facility and demonstrates how the design meets the various requirements imposed by the safety analysis report and the design requirements document

Cold Vacuum Drying Facility Condensate Collection System Design Description. System 19

International Nuclear Information System (INIS)

PITKOFF, C.C.

2000-01-01

The Cold Vacuum Drying (CVD) Facility of Spent Nuclear Fuel (SNF) provides required process systems, supporting equipment, and facilities to support the SNF Project mission. This system design description (SDD) addresses the Condensate Collection System (CCS). This is a general service system. The CCS begins at the condensate outlet of the general process air-handling unit (AHU) and the condensate outlets for the active process bays AHUs. The system terminates at each condensate collection tank (5 total)

Catalytic effects of various catalysts in hydroprocessing of Cold Lake vacuum bottom. Cold Lake zansayu no hydroprocessing ni okeru kakushu shokubai no koka

Energy Technology Data Exchange (ETDEWEB)

Yokoyama, S.; Yamamoto, M.; Maekawa, Y.; Kotanigawa, T. (Government Industrial Development Laboratory, Hokkaido, Sapporo (Japan))

1991-11-07

The effects of various types of catalysts were studied on hydroprocessing of Cold Lake vacuum bottom (CLVB). FeS2 [Py] of an analytical reagent grade was used as sulfide catalyst, Fe2O3(SO4)[sup 2[minus

Performance of indirect solar cabinet dryer

International Nuclear Information System (INIS)

Sreekumar, A.; Manikantan, P.E.; Vijayakumar, K.P.

2008-01-01

In this paper, the development and testing of a new type of efficient solar dryer, particularly meant for drying vegetables and fruit, is described. The dryer has two compartments: one for collecting solar radiation and producing thermal energy and the other for spreading the product to be dried. This arrangement was made to absorb maximum solar radiation by the absorber plate. In this dryer, the product was loaded beneath the absorber plate, which prevented the problem of discoloration due to irradiation by direct sunlight. Two axial flow fans, provided in the air inlet, can accelerate the drying rate. The dryer had six perforated trays for loading the material. The absorber plate of the dryer attained a temperature of 97.2 deg. C when it was studied under no load conditions. The maximum air temperature in the dryer, under this condition was 78.1 deg. C. The dryer was loaded with 4 kg of bitter gourd having an initial moisture content of 95%, and the final desired moisture content of 5% was achieved within 6 h without losing the product colour, while it was 11 h for open sun drying. The collector glazing was inclined at a particular angle, suitable to the location, for absorption of maximum solar radiation. A detailed performance analysis was done by three methods, namely 'annualized cost method', 'present worth of annual savings' and 'present worth of cumulative savings'. The drying cost for 1 kg of bitter gourd was calculated as Rs. 17.52, and it was Rs. 41.35, in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for bitter gourd drying, and it turned out be Rs. 31659.26, which was much higher than the capital cost of the dryer (Rs. 6500). The payback period was calculated as 3.26 years, which was also very small considering the life of the system (20 years). So, the dryer would dry products free of cost during almost its

Safety analysis report for the cold vacuum drying facility, phase 1, supporting civil/structural construction

International Nuclear Information System (INIS)

Pili-Vincens, C.

1998-01-01

The Cold Vacuum Drying Facility is a subproject of the overall Spent Nuclear Fuel Project. This Phase 2 Safety Analysis Report incorporates the CVD systems design and will update the SAR per DOE Order 5480.23 for manual and other Hanford infrastructure changes

Preliminary safety evaluation for the spent nuclear fuel project`s cold vacuum drying system

Energy Technology Data Exchange (ETDEWEB)

Garvin, L.J., Westinghouse Hanford

1996-07-01

This preliminary safety evaluation (PSE) considers only the Cold Vacuum Drying System (CVDS) facility and its mission as it relates to the integrated process strategy (WHC 1995). The purpose of the PSE is to identify those CBDS design functions that may require safety- class and safety-significant accident prevention and mitigation features.

Performance of indirect solar cabinet dryer

Energy Technology Data Exchange (ETDEWEB)

Sreekumar, A.; Manikantan, P.E.; Vijayakumar, K.P. [Solar Thermal Energy Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi 682 022 (India)

2008-06-15

In this paper, the development and testing of a new type of efficient solar dryer, particularly meant for drying vegetables and fruit, is described. The dryer has two compartments: one for collecting solar radiation and producing thermal energy and the other for spreading the product to be dried. This arrangement was made to absorb maximum solar radiation by the absorber plate. In this dryer, the product was loaded beneath the absorber plate, which prevented the problem of discoloration due to irradiation by direct sunlight. Two axial flow fans, provided in the air inlet, can accelerate the drying rate. The dryer had six perforated trays for loading the material. The absorber plate of the dryer attained a temperature of 97.2 C when it was studied under no load conditions. The maximum air temperature in the dryer, under this condition was 78.1 C. The dryer was loaded with 4 kg of bitter gourd having an initial moisture content of 95%, and the final desired moisture content of 5% was achieved within 6 h without losing the product colour, while it was 11 h for open sun drying. The collector glazing was inclined at a particular angle, suitable to the location, for absorption of maximum solar radiation. A detailed performance analysis was done by three methods, namely 'annualized cost method', 'present worth of annual savings' and 'present worth of cumulative savings'. The drying cost for 1 kg of bitter gourd was calculated as Rs. 17.52, and it was Rs. 41.35, in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for bitter gourd drying, and it turned out be Rs. 31659.26, which was much higher than the capital cost of the dryer (Rs. 6500). The payback period was calculated as 3.26 years, which was also very small considering the life of the system (20 years). So, the dryer would dry products free of cost

Beam heat load investigations with a cold vacuum chamber for diagnostics in a synchrotron light source

Energy Technology Data Exchange (ETDEWEB)

Voutta, Robert

2016-04-22

The beam heat load is a crucial input parameter for the cryogenic design of superconducting insertion devices. To understand the discrepancies between the predicted heat load of an electron beam to a cold bore and the heat load observed in superconducting devices, a cold vacuum chamber for diagnostics has been built. Extensive beam heat load measurements were performed at the Diamond light source. They are analysed systematically and combined with complementary impedance bench measurements.

Cold Vacuum Drying facility personnel monitoring system design description

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) instrument air (IA) system that provides instrument quality air to the CVDF. The IA system provides the instrument quality air used in the process, HVAC, and HVAC instruments. The IA system provides the process skids with air to aid in the purging of the annulus of the transport cask. The IA system provides air for the solenoid-operated valves and damper position controls for isolation, volume, and backdraft in the HVAC system. The IA system provides air for monitoring and control of the HVAC system, process instruments, gas-operated valves, and solenoid-operated instruments. The IA system also delivers air for operating hand tools in each of the process bays

Thermal Analysis of Cold Vacuum Drying (CVD) of Spent Nuclear Fuel (SNF)

International Nuclear Information System (INIS)

PIEPHO, M.G.

2000-01-01

The thermal analysis examined transient thermal and chemical behavior of the Multi-Canister Overpack (MCO) container for a broad range of cases that represent the Cold Vacuum Drying (CVD) processes. The cases were defined to consider both normal and off-normal operations at the CVD Facility for an MCO with N Reactor spent fuel. This analysis provides the basis for the MCO thermal behavior at the CVD Facility in support of the safety basis documentation

Safety analysis report for the Cold Vacuum Drying Facility, phase 1, supporting civil/structural construction

International Nuclear Information System (INIS)

Pili-Vincens, C.

1997-01-01

The US Department of Energy established the K Basins Spent Nuclear Fuel Project to address safety and environmental concerns associated with deteriorating spent nuclear fuel presently stored under water in the Hanford Site's K Basins, which are located near the Columbia River. Recommendations for a series of aggressive projects to construct and operate systems and facilities to manage the safe removal of K Basins fuel were made in WHC-EP-0830, Hanford Spent Nuclear Fuel Recommended Path Forward,' and its subsequent update, WHC-SD-SNF-SP-005, Hanford Spent Nuclear Fuel Project Integrated Process Strategy for K Basins Fuel. The integrated process strategy recommendations include the following process steps: fuel preparation activities at the K Basins, including removing the fuel elements from their K Basin canisters, separating fuel particulate from fuel elements and fuel fragments greater than 0.6 cm (0.25 in.) in any dimension, removing excess sludge from the fuel and fuel fragments by means of flushing, as necessary, and packaging the fuel into multicanister overpacks; removal of free water by draining and vacuum drying at the Cold Vacuum Drying Facility (CVDF), a new facility in the 100 K Area of the Hanford Site. This report is contains the safety analysis for the Cold Vacuum Drying Facility, Phase 1

Test of a solar crop dryer

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S. [Teknologisk Institut. SolEnergiCentret, Taastrup (Denmark); Floejgaard Kristensen, E. [Danmarks JordbrugsForskning, Tjele (Denmark); Forman, T. [Aidt Miljoe A/S, Thorsoe (Denmark)

2001-01-01

One of the major goals of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat' was to develop and test a solar crop dryer for use in Ghana. Based on a survey in Ghana (Jensen, Frank and Kristensen, 1999) it was decided to develop a dryer for drying of maize for seed as the increase in value of the crop due the drying here would be high - the dryer may, however, also be used to dry other crops or other items - one unit will e.g. be erected in Ghana to test drying of fish. The capacity of the dryer was defined to be 500 kg having a collector area of approx 25 m{sup 2}. It was decided to let the dryer consist of 5 separate units each with a transparent collector area of 4.77 m{sup 2} and a capacity of approx. 100 kg. The modulized concept has several benfits: If one drying bed is operated improperly this will not affect the total quantity of crops being dried at that time. It is possible to dry different crops (creating different pressure drop) side by side without risking that the crop with the highest pressure drop will be dried improperly. Small dc fans are often cheaper than larger dc fans. The system will be less complex, and an even air distribution over the drying bed is easier obtainable. Finally it is possible to start with only one unit and then gradually increase the capacity of the solar dryer - this will make it easier to invest in a solar dryer. It was further decided that the fans of the dryer should be powered directly by PV-panels in order to make the dryer independent of an often unreliable, missing or expensive grid. The dryer is going to be erected and tested at Silwood Farms situated close to Accra. Silwood Farms has total land acreage of 210 acres where 176 acres are used for cultivating maize - the rest is used for gowing pineapple. A majority of the maize is processed into seed. The main harvest season for maize at Silwood Farms is August/September with a smaller harvest period in January

Cold Vacuum Drying Facility Crane and Hoist System Design Description. System 14

International Nuclear Information System (INIS)

TRAN, Y.S.

2000-01-01

This system design description (SDD) is for the Cold Vacuum Drying (CVD) Facility overhead crane and hoist system. The overhead crane and hoist system is a general service system. It is located in the process bays of the CVD Facility, supports the processes required to drain the water and dry the spent nuclear fuel (SNF) contained in the multi-canister overpacks (MCOs) after they have been removed from the K-Basins. The location of the system in the process bay is shown

Steam generator with perfected dryers

International Nuclear Information System (INIS)

Fenet, J.C.

1987-01-01

This steam generator has vertically superposed array of steam dryers. These dryers return the steam flow of 180 0 . The return of the water is made by draining channels to the steam production zone [fr

Inactivation of Escherichia coli on blueberries using cold plasma with chemical augmentation inside a partial vacuum

Science.gov (United States)

Justification: The mechanism by which cold plasma inactivates pathogens is through the production of free reactive chemical species. Unfortunately, the most reactive chemical species have the shortest half-life. In a vacuum their half-life is believed to be prolonged. Additionally, these reactive sp...

Vacuum-assisted microwave drying characteristics of green bell pepper

Directory of Open Access Journals (Sweden)

Vivek Kumar

2017-04-01

Full Text Available Chopped green bell pepper pieces were blanched (95 °C, 5 min and chemically pretreated (1% potassium metabisulphite solution, 25 min at room temperature before drying in hot air dryer (HAD at various temperature ranges (60 – 80 °C. Three vacuum levels (200, 400, 600 mm Hg and microwave power levels (100, 200, 300 W were also used to dry green bell pepper samples in a vacuum assisted microwave (VAM (2.45 GHz, 0.8 kW dryer. VAM drying methods offered a maximum reduction by four to five times in drying time as compared to that in HAD. The logarithmic model was found to have the best fit based on high R2 and small values of reduced χ2 and RMSE.  VAM method has higher values for effective moisture diffusivity (Deff and lower values for activation energy (Ea, in comparison to the HAD method. 

Multi-shelf domestic solar dryer

International Nuclear Information System (INIS)

Singh, Parm Pal; Singh, Sukhmeet; Dhaliwal, S.S.

2006-01-01

The solar dryer described in this paper can be used for drying various products at home under hygienic conditions with the self guarantee of adulteration free product. This solar dryer is of multi-shelf design, consisting of three perforated trays arranged one above the other. The drying air flows through the product by natural circulation. One of its novel features is variable inclination to capture more solar energy in different seasons. Another novel feature is the option to dry product under shade or without shade as per requirement. The rate of drying is uniform in all the trays due to heating of the air by solar energy in between the trays. The maximum stagnation temperature of this solar dryer was found to be 100 deg. C in the month of November at Ludhiana (31 o N). The moisture evaporation on the 1st, 2nd and 3rd drying day for drying fenugreek leaves was 0.23, 0.18 and 0.038 kg/m 2 h. To overcome the problem of reduction in efficiency on the second and third drying day, a semi-continuous mode of loading has been investigated, in which the efficiency remains almost the same on all drying days. The drying rate in the dryer was more than double that in open shade drying. Moreover, the final moisture content of the product was low enough (7.3% wb) for grinding it to a powder form and for good shelf life (1 year). An uncertainty analysis was performed, and the uncertainty in the efficiency was found to be 1.35%. An economic analysis was performed by three methods. The cost of drying fenugreek leaves in the domestic solar dryer turned out to be about 60% of that in an electric dryer. The cumulative present worth of the savings are much higher (18,316 Rupees) than the capital cost of the dryer (1600 Rupees). The payback period is also very low (<2 years) as compared to the life of the dryer (20 years), so the dryer will dry product free of cost during almost its entire life period. The quality and shelf life of the dried products are comparable to those of

Simulation of Hybrid Solar Dryer

International Nuclear Information System (INIS)

Yunus, Y M; Al-Kayiem, H H

2013-01-01

The efficient performance of a solar dryer is mainly depending on the good distribution of the thermal and flow field inside the dryer body. This paper presents simulation results of a solar dryer with a biomass burner as backup heater. The flow and thermal fields were simulated by CFD tools under different operational modes. GAMBIT software was used for the model and grid generation while FLUENT software was used to simulate the velocity and temperature distribution inside the dryer body. The CFD simulation procedure was validated by comparing the simulation results with experimental measurement. The simulation results show acceptable agreement with the experimental measurements. The simulations have shown high temperature spot with very low velocity underneath the solar absorber and this is an indication for the poor design. Many other observations have been visualized from the temperature and flow distribution which cannot be captured by experimental measurements.

Advanced air detritiation dryer

International Nuclear Information System (INIS)

Anon.

1989-01-01

The isotopic exchange principle has proved effective in increasing air detritiation factors of atmospheric dryers. A CFFTP/AECL Chalk River program has demonstrated detritiation factors of 100,000 in trials. The technology is designed for application on regenerating atmospheric dryers using molecular sieve desiccant beds, used in rooms likely to encounter airborne tritium contamination. Dryer design concepts for dryers at JET (Joint European Torus, England) and ITER have been prepared by Alan Dombra of AECL, using the isotopic exchange technology. The isotopic exchange method works by passing tritiated air over a detritiated desiccant bed. Airborne tritium atoms are exchanged in the bed for ordinary hydrogen atoms from the bed's residual moisture loading. Tritium remains on the bed until it is discharged in a regeneration cycle. During regeneration, the desiccant bed is first heated with hot, dry air to drive off collected tritiated moisture. Airborne tritium removed from the air is collected as a tritiated water distillate and stored for later processing. During the second part of the regeneration cycle, the desiccant bed is washed with clean moist air to elute remaining traces of tritium and to refresh the bed to ready it for another tritium absorption period

40 CFR 1065.342 - Sample dryer verification.

Science.gov (United States)

2010-07-01

...-membrane dryer or thermal chiller. (d) Sample dryer verification procedure. Use the following method to... highest sample water content that you estimate during emission sampling. (3) Introduce the humidified gas... sampling system at a temperature at least 5 °C above the local humidified gas dewpoint. For dryers used in...

Testing Report: Littleford-Day Dryer Operation: Dryer Operation Impacts of Proposed MIS Mitigation Changes

Energy Technology Data Exchange (ETDEWEB)

Shimskey, Rick W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buchmiller, William C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Elmore, Monte R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2007-06-01

Pacific Northwest National Laboratory performed a series of tests using the Littleford Day 22-liter dryer during investigations that evaluated changes in the melter-feed composition for the Demonstration Bulk Vitrification System. During testing, a new melter-feed formulation was developed that improved dryer performance while improving the retention of waste salts in the melter feed during vitrification.

Herbal dryer: drying of ginger (zingiber officinale) using tray dryer

Science.gov (United States)

Haryanto, B.; Hasibuan, R.; Alexander; Ashari, M.; Ridha, M.

2018-02-01

Drying is widely used as a method to preserve food because of its convenience and affordability. Drying of ginger using tray dryer were carried out at various drying conditions, such as air-drying flow, air-drying temperature, and sample dimensions, to achieve the highest drying rate. Samples with various dimensions were placed in the tray dryer and dried using various air-drying flow and temperatures. The weights of samples were observed every 3 minutes interval. Drying was stopped after three times of constant weighing. Data of drying was collected to make the drying curves. Drying curves show that the highest drying rate is achieved using highest air flow and temperature.

Thermal Testing Methods for Solar Dryers

DEFF Research Database (Denmark)

Singh, Shobhana

2017-01-01

Solar food drying is a complex heat and mass transfer phenomena which depend on a number of drying process-dependent parameters such as operating conditions and characteristics of the food product to be dried. The variation in these parameters significantly affects the overall performance...... of the dryer system. Since commercial growth and acceptance of any solar dryer system momentously depend on its performance guarantee, the development of a standard methodology for their thermal testing has become necessary. The standard testing method not only provides better performance management...... of the dryer system but allows the manufacturers to achieve competitive efficiency and good product quality by comparing the available designs. In this chapter, an extensive review of solar dryer performance evaluation has been carried out. Furthermore, the chapter describes the existing testing procedures...

BWR Steam Dryer Alternating Stress Assessment Procedures

Energy Technology Data Exchange (ETDEWEB)

Morante, R. J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hambric, S. A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ziada, S. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-12-01

This report presents an overview of Boiling Water Reactor (BWR) steam dryer design; the fatigue cracking failures that occurred at the Quad Cities (QC) plants and their root causes; a history of BWR Extended Power Uprates (EPUs) in the USA; and a discussion of steam dryer modifications/replacements, alternating stress mechanisms on steam dryers, and structural integrity evaluations (static and alternating stress).

Investigation of the drying airflow at a newly developed dryer geometry for mixed flow grain dryers

Directory of Open Access Journals (Sweden)

Holger Scaar

2016-06-01

Full Text Available The mixed-flow dryer has been a matter of investigation many times regarding drying efficiency, dryer control, and performance enhancement over the past years. However, there is still considerable demand for optimization in terms of energy efficiency and homogeneity of drying. In order to analyze the specific energy consumption and the homogeneity of the drying process, different thermodynamic process conditions have been investigated for the conventional MFD design using numerical and experimental methods. Based on the results obtained, a novel dryer design has been developed. With this, a considerable increase of efficiency is expected. As the fluid dynamic analysis of the first design draft revealed, further development is required until scaling-up and transfer into practice will be possible. While homogeneous airflow conditions could be demonstrated in the core flow region in the center of the dryer, the configuration must be optimized in the near wall regions.

GAS DRYER DESIGN FOR VERMICELLI USING MICROCONTROLLER ATMEGA 8535

Directory of Open Access Journals (Sweden)

Akhmad Mufasil

2013-04-01

Full Text Available The purpose of this research is designing a gas dryer for vermicelli using a microcontroller ATmega 8535 that can overcome the obstacles in the drying department. The microcontroller ATmega 8535 used to regulate the temperature of the drying chamber. This tool design is made to compare between conventional dryer and a theoritical gas dryer in the factory. The method used in this paper is field study in the factory. Based on the experience then theoritical gas dryer design from the factory’s datas. A microcontroller Atmega 8535 is added to the dryer to easier the dryer operation. The result of the theoritical gas dryer design for vermicelli using a microcontroller ATmega 8535, showed a faster time drying for 131,04 kg of vermicelli need 47,72 minutes at a temperature of 40- 55° C.

Cold vacuum chamber for diagnostics: Analysis of the measurements at the Diamond Light Source and impedance bench measurements

Science.gov (United States)

Voutta, R.; Gerstl, S.; Casalbuoni, S.; Grau, A. W.; Holubek, T.; Saez de Jauregui, D.; Bartolini, R.; Cox, M. P.; Longhi, E. C.; Rehm, G.; Schouten, J. C.; Walker, R. P.; Migliorati, M.; Spataro, B.

2016-05-01

The beam heat load is an important input parameter needed for the cryogenic design of superconducting insertion devices. Theoretical models taking into account the different heating mechanisms of an electron beam to a cold bore predict smaller values than the ones measured with several superconducting insertion devices installed in different electron storage rings. In order to measure and possibly understand the beam heat load to a cold bore, a cold vacuum chamber for diagnostics (COLDDIAG) has been built. COLDDIAG is equipped with temperature sensors, pressure gauges, mass spectrometers as well as retarding field analyzers which allow to measure the beam heat load, total pressure, and gas content as well as the flux of particles hitting the chamber walls. COLDDIAG was installed in a straight section of the Diamond Light Source (DLS). In a previous paper the experimental equipment as well as the installation of COLDDIAG in the DLS are described [S. Gerstl et al., Phys. Rev. ST Accel. Beams 17, 103201 (2014)]. In this paper we present an overview of all the measurements performed with COLDDIAG at the DLS and their detailed analysis, as well as impedance bench measurements of the cold beam vacuum chamber performed at the Karlsruhe Institute of Technology after removal from the DLS. Relevant conclusions for the cryogenic design of superconducting insertion devices are drawn from the obtained results.

Cold vacuum chamber for diagnostics: Analysis of the measurements at the Diamond Light Source and impedance bench measurements

Directory of Open Access Journals (Sweden)

R. Voutta

2016-05-01

Full Text Available The beam heat load is an important input parameter needed for the cryogenic design of superconducting insertion devices. Theoretical models taking into account the different heating mechanisms of an electron beam to a cold bore predict smaller values than the ones measured with several superconducting insertion devices installed in different electron storage rings. In order to measure and possibly understand the beam heat load to a cold bore, a cold vacuum chamber for diagnostics (COLDDIAG has been built. COLDDIAG is equipped with temperature sensors, pressure gauges, mass spectrometers as well as retarding field analyzers which allow to measure the beam heat load, total pressure, and gas content as well as the flux of particles hitting the chamber walls. COLDDIAG was installed in a straight section of the Diamond Light Source (DLS. In a previous paper the experimental equipment as well as the installation of COLDDIAG in the DLS are described [S. Gerstl et al., Phys. Rev. ST Accel. Beams 17, 103201 (2014]. In this paper we present an overview of all the measurements performed with COLDDIAG at the DLS and their detailed analysis, as well as impedance bench measurements of the cold beam vacuum chamber performed at the Karlsruhe Institute of Technology after removal from the DLS. Relevant conclusions for the cryogenic design of superconducting insertion devices are drawn from the obtained results.

Heat pump dryers theory, design and industrial applications

CERN Document Server

Alves-Filho, Odilio

2015-01-01

Explore the Social, Technological, and Economic Impact of Heat Pump Drying Heat pump drying is a green technology that aligns with current energy, quality, and environmental concerns, and when compared to conventional drying, delivers similar quality at a lower cost. Heat Pump Dryers: Theory, Design and Industrial Applications details the progression of heat pump drying-from pioneering research and demonstration work to an applied technology-and establishes principles and theories that can aid in the successful design and application of heat pump dryers. Based on the author's personal experience, this book compares heat pump dryers and conventional dryers in terms of performance, quality, removal rate, energy utilization, and the environmental effect of both drying processes. It includes detailed descriptions and layouts of heat pump dryers, outlines the principles of operation, and explains the equations, diagrams, and procedures used to form the basis for heat pump dryer dimensioning and design. The author ...

Cold Vacuum Drying facility heating, ventilation, and Air Conditioning system design description

International Nuclear Information System (INIS)

SINGH, G.

2000-01-01

This System Design Description (SDD) addresses the HVAC system for the CVDF. The CVDF HVAC system consists of five subsystems: (1) Administration building HVAC system; (2) Process bay recirculation HVAC system; (3) Process bay local exhaust HVAC and process vent system; (4) Process general supply/exhaust HVAC system; and (5) Reference air system. The HVAC and reference air systems interface with the following systems: the fire protection control system, Monitoring and Control System (MCS), electrical power distribution system (including standby power), compressed air system, Chilled Water (CHW) system, drainage system, and other Cold Vacuum Drying (CVD) control systems not addressed in this SDD

Criticality safety evaluation report for the Cold Vacuum Drying Facility's process water handling system

International Nuclear Information System (INIS)

Roblyer, S.D.

1998-01-01

This report addresses the criticality concerns associated with process water handling in the Cold Vacuum Drying Facility (CVDF). The controls and limitations on equipment design and operations to control potential criticality occurrences are identified. The effectiveness of equipment design and operation controls in preventing criticality occurrences during normal and abnormal conditions is evaluated and documented in this report. Spent nuclear fuel (SNF) is removed from existing canisters in both the K East and K West Basins and loaded into a multicanister overpack (MCO) in the K Basin pool. The MCO is housed in a shipping cask surrounded by clean water in the annulus between the exterior of the MCO and the interior of the shipping cask. The fuel consists of spent N Reactor and some single pass reactor fuel. The MCO is transported to the CVDF near the K Basins to remove process water from the MCO interior and from the shipping cask annulus. After the bulk water is removed from the MCO, any remaining free liquid is removed by drawing a vacuum on the MCO's interior. After cold vacuum drying is completed, the MCO is filled with an inert cover gas, the lid is replaced on the shipping cask, and the MCO is transported to the Canister Storage Building. The process water removed from the MCO contains fissionable materials from metallic uranium corrosion. The process water from the MCO is first collected in a geometrically safe process water conditioning receiver tank. The process water in the process water conditioning receiver tank is tested, then filtered, demineralized, and collected in the storage tank. The process water is finally removed from the storage tank and transported from the CVDF by truck

Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

Science.gov (United States)

El-Mesery, Hany S; Mwithiga, Gikuru

2015-05-01

A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

Heat transfer and energy efficiency in infrared paper dryers

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Magnus

1999-11-01

Infrared (IR) dryers are widely used in the paper industry, mainly in the production of coated paper grades. The thesis deals with various aspects of heat transfer and energy use in infrared heaters and dryers as employed in the paper industry. Both gas-fired and electric IR dryers are considered and compared. The thesis also provides an introduction to infrared heaters and infrared drying, including a review of recent literature in the field. The transport of thermal radiation inside a paper sheet was investigated and different IR dryers were compared in terms of their ability to transfer energy to the internal parts of a paper sheet. Although there were evident differences in the absorption of radiation between gas-fired and electric IR dryers, the distinction was found not to be as important as has generally been believed. The main differences appeared to be due to the choice of a one- or a two-sided dryer solution, rather than the spectral distributions emitted by the dryers. A method for evaluating the radiation efficiency of IR heaters was proposed. An electric IR heater was evaluated in the laboratory. The radiation efficiency of the heater was shown to be strongly dependent on the power level. The maximum efficiency, found at high power level, was close to 60 %. A procedure for evaluation of the total energy transfer efficiency of an infrared paper dryer was proposed and used in the evaluation of an electric IR dryer operating in an industrial coating machine. The efficiency of the dryer was roughly 40 %. A model for an electric IR heater was developed. The model includes non-grey radiative heat transfer between the different parts of the heater, as well as conduction in reflector material and convective cooling of the surfaces. Using IR module voltage as the only input, model predictions of temperatures and heat flux were found to agree well with experimental data both at steady state and under transient conditions. The model was also extended to include

Design and testing of solar dryers for processing food wastes

Energy Technology Data Exchange (ETDEWEB)

Nijmeh, M.N.; Ragab, A.S.; Emeish, M.S. [University of Jordan, Amman (Jordan). Mechanical Engineering Dept.; Jubran, B.A. [International Islamic University of Malaysia, Kaula Lumpur (Malaysia). Dept. of Mechanical Engineering

1998-12-01

This paper investigates the potential of using two solar dryers manufactured from locally available materials under Jordanian climatic conditions for drying food wastes for utilization as animal feed. The first dryer is a radiative-convective type, while the second is a solar boiler dryer. Tests were also conducted to investigate the nutritious values of the dried products and their suitability as animal feed. It was found from tests that the solar boiler dryer is more efficient than the radiative-convective dryer for producing animal feed in terms of both quality and quantity. The nutritious values of the end products from the dryers were found to be within the international recommended values used for feeding chickens. (author)

Operation experiences of biofuel dryers; Drifterfarenheter fraan aangtorkar och direkta roekgastorkar

Energy Technology Data Exchange (ETDEWEB)

Berge, Christian; Dejfors, Charlotte [AaF Energikonsult Stockholm AB (Sweden)

2000-01-01

A study regarding operation experiences of indirect steam dryers and direct flue gas dryers of biofuels has been conducted. In the study, plants with the two types of dryers have been visited and operational experiences have been gathered and analysed. Results show that the well proven technique with flue gas dryers has a higher availability than the steam dryers. Several plants have problem with the feeding and discharge systems. Material selection is very important to prevent corrosion. Indirect steam dryers have more environmental regulations than flue gas dryers because of the generated condensate from the fuel drying process. Future work should concentrate on material selections, refining the feeding and discharge systems and control system.

Desalination of salty water using vacuum spray dryer driven by solar energy

KAUST Repository

Hamawand, Ihsan

2016-11-18

This paper addresses evaporation under vacuum condition with the aid from solar energy and the recovered waste heat from the vacuum pump. It is a preliminary attempt to design an innovative solar-based evaporation system under vacuum. The design details, equipment required, theoretical background and work methodology are covered in this article. Theoretically, based on the energy provided by the sun during the day, the production rate of pure water can be around 15 kg/m2/day. Assumptions were made for the worst case scenario where only 30% of the latent heat of evaporation is recycled and the ability of the dark droplet to absorb sun energy is around 50%. Both the waste heat from the pump and the heat collected from the photovoltaic (PV) panels are proposed to raise the temperature of the inlet water to the system to its boiling point at the selected reduced pressure.

Desalination of salty water using vacuum spray dryer driven by solar energy

KAUST Repository

Hamawand, Ihsan; Lewis, Larry; Ghaffour, NorEddine; Bundschuh, Jochen

2016-01-01

This paper addresses evaporation under vacuum condition with the aid from solar energy and the recovered waste heat from the vacuum pump. It is a preliminary attempt to design an innovative solar-based evaporation system under vacuum. The design details, equipment required, theoretical background and work methodology are covered in this article. Theoretically, based on the energy provided by the sun during the day, the production rate of pure water can be around 15 kg/m2/day. Assumptions were made for the worst case scenario where only 30% of the latent heat of evaporation is recycled and the ability of the dark droplet to absorb sun energy is around 50%. Both the waste heat from the pump and the heat collected from the photovoltaic (PV) panels are proposed to raise the temperature of the inlet water to the system to its boiling point at the selected reduced pressure.

Stress on Cold Mass Due to the Supporting System of the CMS Coil in the Vacuum Tank

CERN Document Server

Farinon, S

2000-01-01

This report contains a verification analysis of the stress on cold mass coming from the supporting system of the CMS coil in the vacuum tank. The need to carry out this analysis is related to the high mechanical requirements for $9 Al-alloy mandrels (218 MPa yield at cryogenic temperature), demanding accurate analysis of the impact of supporting system on cylinder stress.

Cold vacuum drying facility: Phase 1 FMEA/FMECA session report

International Nuclear Information System (INIS)

Pitkoff, C.

1998-01-01

The mission of the Spent Nuclear Fuel (SNF) Project is to remove the fuel currently located in the K-Basins 100 Area to provide safe handling and interim storage of the fuel. The spent nuclear fuel will be repackaged in multi-canister overpacks, partially dried in the Cold Vacuum Drying Facility (CVDF), and then transported to the Canister Storage Building (CSB) for further processing and interim storage. The CVDF, a subproject to the SNF Project, will be constructed in the 100K area. The CVDF will remove free water and vacuum dry the spent nuclear fuel, making it safer to transport and store at the CSB. At present, the CVDF is approximately 90% complete with definitive design. Part of the design process is to conduct Failure Modes, Effects, and Criticality Analysis (FMECA). A four-day FMECA session was conducted August 18 through 21, 1997. The purpose of the session was to analyze 16 subsystems and operating modes to determine consequences of normal, upset, emergency, and faulted conditions with respect to production and worker safety. During this process, acceptable and unacceptable risks, needed design or requirement changes, action items, issues/concerns, and enabling assumptions were identified and recorded. Additionally, a path forward consisting of recommended actions would be developed to resolve any unacceptable risks. The team consisted of project management, engineering, design authority, design agent, safety, operations, and startup personnel. The report summarizes potential problems with the designs, design requirements documentation, and other baseline documentation

Cold Vacuum Drying facility personnel monitoring system design description (SYS 12); FINAL

International Nuclear Information System (INIS)

PITKOFF, C.C.

1999-01-01

This document describes the Cold Vacuum Drying Facility (CVDF) instrument air (IA) system that provides instrument quality air to the CVDF. The IA system provides the instrument quality air used in the process, HVAC, and HVAC instruments. The IA system provides the process skids with air to aid in the purging of the annulus of the transport cask. The IA system provides air for the solenoid-operated valves and damper position controls for isolation, volume, and backdraft in the HVAC system. The IA system provides air for monitoring and control of the HVAC system, process instruments, gas-operated valves, and solenoid-operated instruments. The IA system also delivers air for operating hand tools in each of the process bays

Evaluation of a dryer in a steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Guandao, Xie; Chen Junliang

1998-01-01

The hooked-vane-type dryer is used in vertical, natural circulation steam generators used in PWR-type nuclear power stations. it separates the fine droplets of water carried by steam so that the steam generator outlet steam moisture is below 0.25%. Such low moisture is demanded to ensure a safe and economic operation of the unit. The dryer is composed of hooked vanes and a draining structure. A series of tests to screen different designs were performed using air-water mixture. The paper presents the results of the investigation of the effect of the number of drainage hooks , the bending angle , distance between two adjacent vanes, and other geometrical parameters on the performance of a hooked-vane-type steam dryer. It indicates that the dryer still works effectively when the moisture of the steam at the dryer inlet changes in a wide range, and that the performance of the dryer is closely related to the geometry of the draining structure . On the basis of the results of this program, a draining structure with an original design was selected and it is presented in the paper. The performance of the selected draining structure is better than that of similar structures in China and abroad. (author)

Rotary drum dryers for coal slurries

Energy Technology Data Exchange (ETDEWEB)

Baunack, F

1983-04-01

The suitability, sizing and internal equipment of rotary drum dryers for high-ash coal slurries are discussed. Rotary dryers will handle also difficult slurries; by suitable drum sizes, lifter blades and chains not only high specific evaporation capacities can be achieved but also very high throughputs of up to 400 tons/h of finished product and high evaporation capacities of 60 tons/h.

Affordable Hybrid Heat Pump Clothes Dryer

Energy Technology Data Exchange (ETDEWEB)

TeGrotenhuis, Ward E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Butterfield, Andrew [Jabil, St. Petersburg, FL (United States); Caldwell, Dustin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crook, Alexander [Jabil, St. Petersburg, FL (United States)

2016-06-30

This project was successful in demonstrating the feasibility of a step change in residential clothes dryer energy efficiency by demonstrating heat pump technology capable of 50% energy savings over conventional standard-size electric dryers with comparable drying times. A prototype system was designed from off-the-shelf components that can meet the project’s efficiency goals and are affordable. An experimental prototype system was built based on the design that reached 50% energy savings. Improvements have been identified that will reduce drying times of over 60 minutes to reach the goal of 40 minutes. Nevertheless, the prototype represents a step change in efficiency over heat pump dryers recently introduced to the U.S. market, with 30% improvement in energy efficiency at comparable drying times.

Comparison of carrot (Daucus carota drying in microwave and in vacuum microwave

Directory of Open Access Journals (Sweden)

R. Béttega

2014-06-01

Full Text Available Drying is a single operation employed to prolong the life of a large quantity of vegetables. Carrot (Daucus carota drying has been the subject of many studies. This plant has been highlighted in the human diet for having high nutritional value, mainly due to the high content of β-carotene. In this work, carrot drying behavior was studied in a regular microwave dryer and a vacuum microwave dryer. A vacuum of 450 mmHg was applied for drying of carrot in different geometrical shapes (cubes, discs and sticks. The samples were dried at power ratings of 1.0 W/g, 1.5 W/g and 2.0 W/g for both methods of drying. The evolution of physical properties such as density, volume and porosity was monitored and related to the moisture content of the sample and to the method of drying and power rating used. The geometric shape of the sample influenced the drying kinetics and it was verified that the cubic form was responsible for a slower drying. The application of vacuum showed no major changes in the drying kinetics in microwave but influenced the physical properties of the material. The influence of power ratings on the content of β-carotene was also evaluated and discussed. The main difference observed was the lower shrinkage of the samples dried in the vacuum microwave compared to those dried only in microwave.

CFD analysis for greenhouse effect solar dryer

International Nuclear Information System (INIS)

Wulandani, D.; Abdullah, K.; Hartulistiyoso, E.; Siswantara, I.

2006-01-01

Greenhouse Effect (GHE) solar dryer is a transparent wall structure, consists of absorber plate as solar heat collector, product holders (tray or batch) and fans to discharge moisture from the product. GHE solar dryer is one of the alternative dryer for the farmer and merchants to improve the quality of dried products. Direct sun drying is still popular choice by farmers because it is cheap and simple. However, the method is greatly dependent on the existence of solar irradiation and the product is contaminated very easily by pollution and dirt. The general constraint in designing artificial dryer is the problem of non-uniformity of final moisture content of product, especially for the cabinet of rack type dryer. This condition can be solved by providing uniform distribution of temperature, relative humidity (RH) and airflow velocity of the drying air. Therefore, in this study, such problem was approached by conducting flow simulation within the drying structure by using computational fluid dynamics (CFD) technology to determine the proper position of drying air inlet and outlet, location and capacity of the heat exchanger unit, the position and the capacity of the fan, to produce uniform distribution of the drying air temperature, RH and airflow velocity within the drying chamber.(Author)

Ultrasonic Spray Drying vs High Vacuum and Microwaves Technology for Blueberries

Science.gov (United States)

Candia-Muñoz, N.; Ramirez-Bunster, M.; Vargas-Hernández, Y.; Gaete-Garretón, L.

Interest in high quality foods: good taste and a high content of nutrients with healthy beneficial effects are increasing. Fruits have good properties but, they are lost because the oxidation process, additionally, for different reasons a 40% of harvested fruit are lost. To conserve the fruit properties an ultrasonic assisted spray dryer was developed and tested, comparing its results with microwave-vacuum drying technology. Results did shown taste, color, smell, particle shape and size distribution better than the conventional one. The antioxidants conservation were quite good except in the anthocyanins, in which the microwave and vacuum technology shown best results.

Performance of modified greenhouse dryer with thermal energy storage

Directory of Open Access Journals (Sweden)

Om Prakash

2016-11-01

Full Text Available In this attempt, the main goal is to do annual performance, environomical analysis, energy analysis and exergy analysis of the modified greenhouse dryer (MGD operating under active mode (AM and passive mode (PM. Thermal storage is being applied on the ground of MGD. It is applied in three different ways namely barren floor, floor covered with black PVC sheet (PVC and Black Coated. Experimental study of dryers in no-load conditions reveals that floor covered with a black PVC sheet is more conducive for drying purpose than other floors. The MGD under AM is found to be more effective as compared to PM for tomato and capsicum, which are high moisture content crops. For medium moisture content crop (potato chips, both dryers show relatively similar drying performance. Crops dried inside the greenhouse dryer are found to be more nutrient than open sun dried crops. The payback period of the modified greenhouse dryer under passive mode is found to be 1.11 years. However, for the active mode of the modified greenhouse dryer is only 1.89 years. The embodied energy of the passive mode of the dryer is a 480.277 kWh and 628.73 kWh for the active mode of the dryer. The CO2 emissions per annum for passive and active mode greenhouse dryers are found to be 13.45 kg and 17.6 kg respectively. The energy payback time, carbon mitigation and carbon credit have been calculated based type of crop dried. The range of exergy efficiency is 29%–86% in MGD under PM and 30%–78% in the MGD under AM. The variation of Heat utilization factor (HUF for MGD under PM is 0.12–0.38 and 0.26–0.53 for MGD under AM. The range of co-efficient of performances (COP for MGD under PM is 0.55–0.87 and 0.58–0.73 for MGD under AM.

Experimental investigations of a chimney-dependent solar crop dryer

Energy Technology Data Exchange (ETDEWEB)

Afriyie, J.K.; Nazha, M.A.A.; Rajakaruna, H. [School of Engineering and Technology, De Montfort University, Queens Building, The Gateway, Leicester LE1 9BH (United Kingdom); Forson, F.K. [Department of Mechanical Engineering, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana)

2009-01-15

An experimental investigation into the performance of a solar crop dryer with solar chimney and no air preheating is described. Tests were first performed on the cabinet dryer, using a normal chimney. The trials were repeated with a solar chimney. Still with the solar chimney, further trials were carried out with the roof of the drying chamber inclined further to form a tent dryer. The described tests include no-load tests for airflow rate measurements and drying tests, with cassava as the crop. Air velocities, temperatures, ambient relative humidity and the drop in crop moisture contents at different stages of the drying process are also presented. The effects of the various configurations described above on the drying process are deduced and discussed while comparing the experimental results with one another. In addition, the performance of the dryer in relation to other natural convection dryers is discussed. The results show that the solar chimney can increase the airflow rate of a direct-mode dryer especially when it is well designed with the appropriate angle of drying-chamber roof. However, the increase in flow rate only increases the drying rate when the relative humidity (RH) of the ambient air is below a certain mark (60% for cassava). (author)

Silk cocoon drying in forced convection type solar dryer

International Nuclear Information System (INIS)

Singh, Panna Lal

2011-01-01

The thin layer silk cocoon drying was studied in a forced convection type solar dryer. The drying chamber was provided with several trays on which the cocoons loaded in thin layer. The hot air generated in the solar air heater was forced into drying chamber to avoid the direct exposure of sunlight and UV radiation on cocoons. The drying air temperature varied from 50 to 75 o C. The cocoon was dried from the initial moisture content of about 60-12% (wb). The drying data was fitted to thin layer drying models. Drying behaviour of the silk cocoon was best fitted with the Wang and Singh drying model. Good agreement was obtained between predicted and experimental values. Quality of the cocoons dried in the solar dryer was at par with the cocoons dried in the conventional electrical oven dryer in term of the silk yield and strength of the silk. Saving of electrical energy was about 0.75 kWh/kg cocoons dried. Economic analysis indicated that the NPV of the solar dryer was higher and more stable (against escalation rate of electricity) as compare to the same for electrical oven dryer. Due to simplicity in design and construction and significant saving of operational electrical energy, solar cocoon dryer seems to be a viable option.

Development of an Active Solar Crop Dryer: Design Analysis and Performance Evaluation

International Nuclear Information System (INIS)

Itodo, I. N.; Adewole, A.M.; Edemaku, S.K.

2002-01-01

A forced convection indirect solar dryer powered by a PVC module was designed and evaluated. The performance of the dryer was poor; its drying rate, collector and system drying efficiency were 0.74 kg/day, 12% and 10% respectively. The dryer was redesigned and modified into a direct forced convection type- Its design analysis and performance evaluation was undertaken by drying mashed cassava. The drying rate, system drying collector and pick-up efficiencies were 1,6 kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9 kg/day. The collector efficiency compared very well to the designed value of 48% and may not need further improvement. The pick-up efficiency also compared well with typical averages for this dryer type. The drying rate and system drying efficiency Indicate the need for further development of this dryer. Prediction equations were developed from the results of measured differences in collector, dryer and ambient air temperatures plotted on graphs and applying regression. It is recommended that the volumetric air-flow rate across the drying unit should he improved by affecting the tan speed and air inlet area of the dryer. The improved dryer will subsequently be compared to a natural convection dryer so that an appropriate dryer technology can be recommended for the rural small-scale farmers

Design and performance evaluation of a new hybrid solar dryer for banana

International Nuclear Information System (INIS)

Amer, B.M.A.; Hossain, M.A.; Gottschalk, K.

2010-01-01

A hybrid solar dryer was designed and constructed using direct solar energy and a heat exchanger. The dryer consists of solar collector, reflector, heat exchanger cum heat storage unit and drying chamber. The drying chamber was located under the collector. The dryer was operated during normal sunny days as a solar dryer, and during cloudy day as a hybrid solar dryer. Drying was also carried out at night with stored heat energy in water which was collected during the time of sun-shine and with electric heaters located at water tank. The efficiency of the solar dryer was raised by recycling about 65% of the drying air in the solar dryer and exhausting a small amount of it outside the dryer. Under Mid-European summer conditions it can raise up the air temperature from 30 to 40 deg. C above the ambient temperature. The solar dryer was tested for drying of ripe banana slices. The capacity of the dryer was to dry about 30 kg of banana slices in 8 h in sunny day from an initial moisture content of 82% to the final moisture content of 18% (wb). In the same time it reduced to only 62% (wb) moisture content in open sun drying method. The colour, aroma and texture of the solar dried products were better than the sun drying products.

Assessment of the bacterial contamination of hand air dryer in washrooms.

Science.gov (United States)

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S; Zayed, M E; Al-Johny, Bassam O; Wainwright, Milton

2016-03-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows that Staphylococcus haemolyticus, Micrococcus luteus, Pseudomonas alcaligenes, Bacillus cereus and Brevundimonad diminuta/vesicularis were emitted from all of the dryers sampled, with 95% showing evidence of the presence of the potential pathogen S. haemolyticus. It is concluded that hot air dryers can deposit pathogenic bacteria onto the hands and body of users. Bacteria are distributed into the general environment whenever dryers are running and could be inhaled by users and none-users alike. The results provide an evidence base for the development and enhancement of hygienic hand drying practices.

Sustainability assessment of heat exchanger units for spray dryers

International Nuclear Information System (INIS)

Caglayan, Hasan; Caliskan, Hakan

2017-01-01

In this study, the sustainability assessment is performed to the system known as heat exchanger unit with spray dryer. The five-different dead state temperatures (0-5-10-15-20 °C) are considered. It is found that the heat exchanger has the highest energy efficiency (63.32%), while the overall system has the lowest one (5.56%). So, the combination of the spray dryer with the heat exchanger is more effective. On the other hand, the overall exergy efficiency of the system is lower than the heat exchanger and spray dryer for all of the dead state (environmental) temperatures. The exergy efficiency of the heat exchanger is inversely proportional to the dead state temperature, and the maximum rate is found as 49.65% at 0 °C. Furthermore, the exergy efficiencies of the spray dryer and overall system are directly proportional to the dead state temperatures, and the corresponding maximum rates are found to be 26.41% and 24.32% at 20 °C, respectively. Also, the exergy destruction is directly proportional to the dead state temperatures. The minimum and maximum exergy destruction rates are found at the dead state temperatures of 0 °C and 20 °C, respectively. Furthermore, the most sustainable system is found as the heat exchanger unit. - Highlights: • Thermodynamic analyses of industrial heat exchangers and spray dryers. • Sustainability of heat exchangers for spray dryers. • Dead state temperature effects on exergy efficiencies of heat exchangers and spray dryers.

solar dryer with biomass backup heater for drying fruits

African Journals Online (AJOL)

SOLAR DRYER WITH BIOMASS BACKUP HEATER FOR DRYING FRUITS: DEVELOPMENT AND PERFORMANCE ANALYSIS. ... Journal of Science and Technology (Ghana) ... Most solar dryers rely on only solar energy as the heat source.

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1998-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S.; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1997-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Assessment of the bacterial contamination of hand air dryer in washrooms

OpenAIRE

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S.; Zayed, M.E.; Al-Johny, Bassam O.; Wainwright, Milton

2016-01-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows th...

Optimization of frozen wild blueberry vacuum drying process

Directory of Open Access Journals (Sweden)

Šumić Zdravko M.

2015-01-01

Full Text Available The objective of this research was to optimize the vacuum drying of frozen blueberries in order to preserve health benefits phytochemicals using response surface methodology. The drying was performed in a new design of vacuum dryer equipment. Investigated range of temperature was 46-74°C and of pressure 38-464 mbar. Total solids, total phenolics, vitamin C, anthocyanin content and total color change were used as quality indicators of dried blueberries. Within the experimental range of studied variables, the optimum conditions of 60 °C and 100 mbar were established for vacuum drying of blueberries. Separate validation experiments were conducted at optimum conditions to verify predictions and adequacy of the second-order polynomial models. Under these optimal conditions, the predicted amount of total phenolics was 3.70 mgCAE/100dw, vitamin C 59.79 mg/100gdw, anthocyanin content 2746.33 mg/100gdw, total solids 89.50% and total color change 88.83. [Projekat Ministarstva nauke Republike Srbije, br. TR 31044

The HIE-ISOLDE Vacuum System

CERN Document Server

Vandoni, G; Radwan, K; Chiggiato, P

2014-01-01

The High Intensity and Energy Isolde (HIE-Isolde) project aims at increasing the energy and intensity of the radioactive ion beams (RIB) delivered by the present Rex-Isolde facility. Energy up to 10MeV/amu will be reached by a new post-accelerating, superconducting (SC) linac. Beam will be delivered via a HEBT to three experimental stations for nuclear physics. To keep the SC linac compact and avoid cold-warm transitions, the cryomodules feature a common beam and insulation vacuum. Radioactive ion beams require a hermetically sealed vacuum, with transfer of the effluents to the nuclear ventilation chimney. Hermetically sealed, dry, gas transfer vacuum pumps are preferred to gas binding pumps, for an optimized management of radioactive contamination risk during maintenance and intervention. The vacuum system of the SC-linac is isolated by two fast valves, triggered by fast reacting cold cathode gauges installed on the warm linac, the HEBT and the experimental stations. Rough pumping is distributed, while the H...

Vacuum gauges

International Nuclear Information System (INIS)

Power, B.D.; Priestland, C.R.D.

1978-01-01

This invention relates to vacuum gauges, particularly of the type known as Penning gauges, which are cold cathode ionisation gauges, in which a magnetic field is used to lengthen the electron path and thereby increase the number of ions produced. (author)

Development and Evaluation of Solar Tunnel Dryer for Commercial Fish Drying

Science.gov (United States)

Mohod, A. G.; Khandetod, Y. P.; Shrirame, H. Y.

2014-01-01

The local practice of drying fish in open sun drying poses problems such as high moisture content, uncontrolled drying and contamination. These problems can be avoided by proper use of improved methods such as the solar tunnel dryer, which results in faster drying of fish. The semi cylindrical walk-in type natural convection solar tunnel dryer, having drying area of 37.5 m2 was developed and evaluated for the drying of fish products in comparison with the conventional method of open sun drying. The experiments were conducted without fish and with fish to evaluate the performance of solar tunnel dryer. The average rise in temperature inside the solar tunnel dryer was found to be 11.24 °C and 18.29 °C over the ambient temperature during no load test in winter and summer respectively. The average 28 % saving in time was observed for selected fish drying using solar tunnel dryer over open sun drying method with average drying efficiency of 19 %. The economics was calculated for drying of prawns ( Parapaeneopsis stylifera) by solar tunnel dryer and open sun drying system on the basis of business as a whole. The economics of the solar tunnel dryer is presented in term of Net present worth, Benefit-Cost Ratio, Payback period, Profitability index and Internal rate of return. The pay back period for solar tunnel dryer was found to be 2.84 years.

Neural network modeling of drying of rice in BAU-STR dryer

Science.gov (United States)

Alam, Md. Ashraful; Saha, Chayan Kumer; Alam, Md. Monjurul; Ashraf, Md. Ali; Bala, Bilash Kanti; Harvey, Jagger

2018-05-01

The experimental performance and artificial neural network modeling of rice drying in BAU-STR dryer is presented in this paper. The dryer consists of a biomass stove as a heat source, a perforated inner bin and a perforated outer bin with annular space for grains, and a blower (1 hp) to supply heated air. The dryer capacity was 500 kg of freshly harvested rice. Twenty experimental runs were conducted to investigate the experimental performance of the dryer for drying of rice. An independent multilayer neural network approach was used to predict the performance of the BAU-STR dryer for drying of rice. Ten sets of experimental data were used for training using back propagation algorithm and another ten sets of data were used for testing the artificial neural network model. The prediction of the performance of the dryer was found to be excellent after it was adequately trained. The statistical analysis showed that the errors (MSE and RMSE) were within and acceptable range of ±5% with a coefficient of determination (R2) of 99%. The model can be used to predict the potential of the dryer for different locations, and can also be used in a predictive optimal control algorithm.

Evaluation of hybrid solar – biomass dryer with no load

Directory of Open Access Journals (Sweden)

Yassen Tadahmun Ahmed

2014-07-01

Full Text Available Experimental study was carried out to investigate the performance of designed and fabricated hybrid solar-biomass dryer without load. The solar side was a natural convection mixed mode, while the biomass side was a hot air produced from a burner/gas to gas heat exchanger. The experiments have been conducted to test the dryer temperature, inlet and outlet relative humidity, outlet velocity, and biomass feeding rate. In the solar mode the maximum dryer temperature was 63°C. Behaviours of the velocity in the dryer was found to follow solar radiation available to the dryer. The velocity was in the range of 0.6 – 1.35 m/s through the 0.0176 m2 area of the outlet when the solar radiation was in the range of 150 – 880 W/m2. Two feeding rates of wood were used to investigate the dryer performance through the night. The results showed that at feeding rate 278 g/hr, the drying air mean temperature was 62 ºC. This temperature was more suitable than the measured drying air temperature at feeding rate 490 g/hr. Also the 62 °C drying environment is more stable and feasible for drying almost all types of products.

Effect of vacuum and modified atmosphere packaging on microbiological properties of cold-smoked trout

Science.gov (United States)

Đorđević, J.; Pavlićević, N.; Bošković, M.; Janjić, J.; Glišić, M.; Starčević, M.; Baltić, M. Ž.

2017-09-01

Because of the importance of different packaging methods for the extension of fish shelf life, as a highly perishable food, the aim of the present study was to examine the effect of vacuum and modified atmosphere packaging on the total Enterobacteriaceae and lactic acid bacteria counts of cold-smoked Salmon trout (Oncorhynchus mykiss) stored at 3°C during six weeks. Trout fillets were vacuumed packaged (VP) or packaged in one of two different modified atmospheres, with gas ratio of 50%CO2/50%N2 (MAP1) and 90%CO2/10%N2 (MAP2) and analysed on days 0, 7, 14, 21, 28, 35 and 42. Both the total Enterobacteriaceae and total lactic acid bacteria counts increased in the trout fillets in all packaging types during storage. A significantly lower total Enterobacteriaceae count was determined in the MAP fish compared to the VP fish, with the weakest growth rate and lowest numbers attained in MAP2 fillets. The lactic acid bacteria count was higher in trout packaged in MAP compared to VP, with the highest number in the MAP with 90% CO2 (MAP2).

Effectiveness of a heat exchanger in a heat pump clothes dryer

Science.gov (United States)

Nasution, A. H.; Sembiring, P. G.; Ambarita, H.

2018-02-01

This paper deals with study on a heat pump clothes dryer coupled with a heat exchanger. The objective is to explore the effects of the heat exchanger on the performance of the heat pump dryer. The heat pump dryer consists of a vapor compression cycle and integrated with a drying room with volume 1 m3. The power of compressor is 800 Watt and the refrigerant of the cycle is R22. The heat exchanger is a flat plate type with dimensions of 400 mm × 400 mm × 400 mm. The results show the present of the heat exchanger increase the performance of the heat pump dryer. In the present experiment the COP, TP and SMER increase 15.11%, 4.81% and 58.62%, respectively. This is because the heat exchanger provides a better drying condition in the drying room with higher temperature and lower relative humidity in comparison with heat pump dryer without heat exchanger. The effectiveness of the heat exchanger is also high, it is above 50%. It is suggested to install a heat exchanger in a heat pump dryer.

Performance of a desiccant assisted packed bed passive solar dryer for copra processing

Directory of Open Access Journals (Sweden)

Padmanaban Govindarajulu

2017-01-01

Full Text Available In this paper, the performance of a novel desiccant assisted packed bed passive solar dryer was evaluated for copra processing and compared with conventional passive solar dryer. This novel solar dryer consists of a desiccant assisted packed bed solar air heater attached with a dryer cabin. The desiccant and phase change materials packed in the solar air heater has control the humidity and retains the heat for longer duration, respectively. The performance of the dryer was evaluated (in terms of drying time to attain the final equilibrium moisture content, drying rate, specific moisture extraction rate, pick-up efficiency, and dryer efficiency under the meteorological conditions of Coimbatore city in India during March and April 2016. The copra was dried from initial moisture content (wet basis of about 52% to the final moisture content (wet basis of about 8% in 62 hours with specific moisture extraction rate of 0.82 kg/kWh. The drying time was reduced by about 44 hours when compared to the conventional passive solar dryer. The dryer pick-up efficiency was varied between about 10% and 65%. The average dryer thermal efficiency was calculated to be about 32%. The quality of final dried product was found to be good.

New complex-dryers with RE for coatings

International Nuclear Information System (INIS)

Ge, G.

1998-01-01

Full text: The complex coating dryers are produced with good 2-Ethylhexanoic acid, rare earths and other metals. Simply using such a complex drier can get the total effect instead of the traditional dryers such as Co, Mn, Pb, Zn, Ca etc. It has advantages of saving quantity, decreasing cost, simplifying process, making the operation convenient, good quality, good stability and without Pb. Invention patent of China requisition number is 95119867.X

The impact of immersion protection requirements on hair dryer electrocutions in the USA.

Science.gov (United States)

Rodgers, Gregory B; Garland, Sarah

2012-12-01

To evaluate the effectiveness of the immersion protection requirements of a voluntary safety standard for portable handheld hair dryers in preventing electrocution deaths in the USA. The present work was an interrupted time series study design. Data on annual hair dryer-related electrocution deaths resulting from water contact were developed for the 1980-2007 study period. A multivariate Poisson regression model for rate data was used to evaluate the impact of the immersion protection requirements during the post-intervention period. The analysis controlled for the estimated number of hair dryers in use and the estimated number of US homes equipped with ground fault circuit interrupters, safety devices that would address hair dryer electrocutions even in the absence of the immersion protection requirements of the voluntary standard. The implementation of the 1987 and 1991 immersion protection requirements of the voluntary standard for portable handheld hair dryers was the intervention studied. The main outcome measure was the estimated reduction in the hair dryer electrocution rate associated with the immersion protection requirements of the voluntary standard. After controlling for covariates, the immersion protection requirements were estimated to reduce the rate of hair dryer immersion electrocution deaths by 96.6% (95% CI, 90.8% to 98.8%). This suggests the prevention of about 280 immersion electrocution deaths involving hair dryers during the post-intervention period (1987-2007). The immersion protection requirements of the voluntary safety standard for hair dryers have been highly effective in reducing hair dryer electrocutions.

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

Energy Technology Data Exchange (ETDEWEB)

Kouchakzadeh, Ahmad [Agri Machinery Engineering, Ilam University, Ilam (Iran, Islamic Republic of); Tavakoli, Teymur [Agri Machinery Engineering, Tarbyat Modares University, Tehran (Iran, Islamic Republic of)

2011-07-15

Highlights: {yields} Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. {yields} Using thermophysical properties of air and matter. {yields} This manner could be utilized in similar dryer for other agricultural products. {yields} Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

International Nuclear Information System (INIS)

Kouchakzadeh, Ahmad; Tavakoli, Teymur

2011-01-01

Highlights: → Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. → Using thermophysical properties of air and matter. → This manner could be utilized in similar dryer for other agricultural products. → Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

Development and performance evaluation of forced convection potato solar dryer

International Nuclear Information System (INIS)

Khan, M.A.; Sabir, M.S.; Iqbal, M.

2011-01-01

This research paper deals with the design development and testing of a forced convection solar dryer, for drying and converting to flour of high moisture content vegetables like potatoes. The angle of solar collector was made adjustable for the absorption of maximum solar radiation by the absorber plate. The air flow rate was controlled by adjustable gate valve to find the optimum flow rate for dehydration of the product. The penetration of solar radiation raised the temperature of the absorber plate of the dryer to 110 deg. C during the operation under stagnation or no load conditions. The maximum air temperature attained in the solar air heater, under this condition was 80 deg. C. The dryer was loaded with 12 Kg of blanched potato chips having an initial moisture content of 89.75%, and the final desired moisture content of 6.95% was achieved within five hours without losing the color of potato chips, while the moisture contents reduction was from 89.75% to 33.75% for five hours in open sun drying under shade. The drying cost for 1 Kg of potatoes was calculated as Rs. 245 and it was Rs. 329 in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for blanched potato chips drying, and it turned out be Rs.163177.67/- which was much higher than the capital cost of the dryer (Rs. 25000). The payback period was calculated as 0.89 years, which was also very small considering the life of the system (20 years). (author)

MICROBIOLOGICAL CHARACTERISTICS OF THE AIR BLOWN BY WARM AIR HAND DRYERS

Directory of Open Access Journals (Sweden)

Recai OÐUR; Omer Faruk TEKBAS; Osman HANCI; Umut OZCAN

2005-02-01

Full Text Available The aim of the study was to determine the microbiological characteristics of air blown from warm air hand dryers, and to compare findings with the microbiological characteristics of indoor air in which the dryer settled. Air samples was taken from different public places (shopping centers, restaurants and hospitals and investigated for total viable counts, coagulase negative Staphylococcus, E. Coli, Staphylococcus aureus and enteric pathogens. There were differences between sampling indoor places for some of the microorganisms, but all of the air samples taken from dryers contained more microorganisms than indoor air, and the differences between hand dryers and indoor air were statistically significant (p<0.05 except for enteric pathogens. As a result it could be said that warm air hand dryers could be microbiological contamination sources in restrooms or the other places that they are used. [TAF Prev Med Bull 2005; 4(1.000: 1-7

Integration of thickener underflow into thermal dryer circuit. Final report

Energy Technology Data Exchange (ETDEWEB)

McClaine, A.W.; Breault, R.W.

1998-12-31

A large number of coal preparation plants in the United States are troubled with coal fines and associated plant operation problems. As part of their process, these plants use thermal dryers for producing product coal, cyclones for first-stage recovery of coal fines, and wet scrubbers for the second-stage removal of coal fines carry-over from the dryer exhaust gas. The first challenge for these plants is to recover the clean ultra-fine coal captured in the scrubbers rather than to dispose of it in settling ponds. The second challenge is to mitigate the over-dry fine coal dusting problems in the dryer product. Prior to the completion of this program, the difficulties of the first challenge involving the recovery and use of fine clean coal from the thermal dryer scrubber effluent had not been solved. The second challenge, controlling fine coal dusting, was previously met by applying a solution of surfactants and process water to the over-dry coal fraction. As a result of the demonstration provided by the performance of this program, the implementation of a simple process improvement, involving the use of a thickener in combination with a belt press, simultaneously solved both challenges: the de-dusting and the dryer scrubber effluent recovery issues. The objective of this project was to: (1) Use a clean coal thickener with a squeeze belt press to recover the ultra-fine coal in dryer scrubber effluent; (2) Demonstrate that the coal-water mixture (CWM) produced from scrubber sludge of a thermal dryer can be used as a dust suppressant. The thickener/belt press system has increased the production of JWRI Mine Number 4 by approximately 0.7%. This production increase was accomplished by recovering and re-using 3 metric tons/hr (3.3 tons/hr) of coal fines that were previously sent to holding ponds, returning this as a 50% CWM to de-dust the 430 metric tons/hr (470 tons/hr) of existing dryer production.

Test and study for dryer used in steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Xie Guandao; Chen Junliang

1994-10-01

Dryer used in steam generator is composed of hooked-vanes and draining structure. The influences of the number of drainage hooks on a hooked-vane, bending angle, distance between two adjacent hooked-vanes, etc. on separation effect are introduced. The improving process of draining structure is also described. The test indicates that the hooked-vanes type dryer allows to change inlet moisture in a large range and that the performance of the dryer is closely related to draining structure. A draining structure with original creation which is selected by the test is presented, its drainage effect is better than that of similar structures at home and abroad. (2 tabs., 21 figs.)

Processamento de achocolatado de cupuaçu por spray-dryer Cupuassu chocolate drink powder processed by spray-dryer

Directory of Open Access Journals (Sweden)

Suzana Caetano da Silva Lannes

2003-03-01

Full Text Available O achocolatado de cupuaçu é uma mistura do pó de cupuaçu, açúcar, aroma e outros ingredientes constantes da formulação. Este produto formulado foi processado por spray-dryer, gerando um produto seco, pulverizado e instantaneizado. O achocolatado acrescido de água (concentrado passa pelo spray-dryer formando glóbulos de pequeno diâmetro que são arrastados por uma corrente de ar quente. A rápida evaporação de líquido permite manter baixa a temperatura do ar na secagem, não afetando o produto. O pó de cupuaçu não dispersa prontamente em água devido ao seu conteúdo de óleo. Conseqüentemente, necessita-se de uma forma desengordurada para se obter instantaneização. A secagem por spray-dryer reúne as melhores condições de rendimento técnico em comparação com outros processos. Obtiveram rendimentos de processo acima de 20% e a instantaneização completa do produto.Cupuassu chocolate drink powder is a mixture of cupuassu powder, sugar, flavour and other ingredients of formulation. The product was processed by spray-dryer, leading a dry, pulverized and instantised product. The chocolate drink powder with water (concentrated pass through spray-dryer forming small diameter globules that are arrested by a hot air stream. The rapid evaporation allows keeping low temperature at drying air, and no affecting the product. The process is a set of better conditions of technique and economical efficiency in comparison to other process. Cupuassu powder does not disperse readily in water owing to its oil content. Consequently, a form of cocoa with the oil removed is needed to produce an acceptably instant drink. The results obtained were satisfactory, due to the complete instantisation of the product after processing.

Evaluation of the role of Carnobacterium piscicola in spoilage of vacuum- and modified-atmosphere-packed cold-smoked salmon stored at 5 degrees C.

Science.gov (United States)

Paludan-Müller, C; Dalgaard, P; Huss, H H; Gram, L

1998-02-17

The microflora on spoiled cold-smoked salmon often consists of a mixture of lactic acid bacteria (LAB) and Gram-negative bacteria. To elucidate the role of the different groups, a storage trial was carried out in which nisin and CO2 were used for the selective inhibition of the two bacterial groups. The shelf-life of vacuum-packed cold-smoked salmon, recorded by sensory evaluation, was four weeks at 5 degrees C and the microflora was composed of LAB (10(6)-10(7) cfu/g) with an associate Gram-negative flora in varying levels (10(5)-10(7) cfu/g). The addition of nisin and/or a CO2-atmosphere increased the shelf-life to five or six weeks and limited the level of LAB to about 10(4)-10(6), 10(3)-10(6) and 10(2)-10(4) cfu/g, respectively. CO2-atmosphere +/- nisin inhibited the growth of Gram-negative bacteria, whereas nisin had no effect on these in vacuum packages. The Gram-negative flora on vacuum-packed salmon was dominated by a Vibrio sp., resembling V. marinus, Enterobacteriaceae (Enterobacter agglomerans, Serratia liquefaciens and Rahnella aquatilis) and occasionally Aeromonas hydrophila. Irrespective of the addition of nisin and/or CO2-atmosphere, the LAB microflora was dominated by Carnobacterium piscicola, which was found to account for 87% of the 255 LAB isolates characterized. Whole-cell-protein patterns analysed by SDS-PAGE confirmed the Carnobacterium species identification. The spoilage potential of C. piscicola isolates was further studied by inoculation of approx. 10(6) cfu/g in cold-smoked salmon stored at 5 degrees C. The salmon did not spoil within 4 weeks of storage in vacuum- or CO2-atmosphere, and it is concluded that despite high levels (> 10(7) cfu/g) of C. piscicola, sensory rejection was caused by autolytic changes. This was supported by the development of soft texture and sour, rancid and bitter off-flavours at the point of spoilage, irrespective of the length of shelf-life and low or high total counts of LAB and Gram-negative bacteria.

Generation of x-ray radiation in a storage ring by a superconductive cold-bore in-vacuum undulator

Directory of Open Access Journals (Sweden)

S. Casalbuoni

2006-01-01

Full Text Available The first beam measurements with a cold-bore superconducting in-vacuum undulator in a storage ring are reported. Undulators are x-ray generators in light sources. The physical limitations of these devices limit the intensity and the brilliance of the x-ray beam. At present the undulators are made from permanent magnets. It was shown in earlier papers that at low electron beam intensities superconductive wires in the vacuum beam pipe can overcome the limitations inherent to permanent magnet undulators. It was argued that the use of these novel devices in light sources with high beam currents may be limited by the extreme anomalous skin effect regime in Cu at 4.2 K, which has so far undergone very little investigation, and the power deposited by the infrared part of the synchrotron radiation. The purpose of this paper is to present measurements of these effects at the synchrotron light source ANKA with stored currents up to 200 mA.

Experimental Investigation on an Energy Efficient Solar Tunnel Dryer

OpenAIRE

M. R. Seshan Ram

2012-01-01

The research determines the effectiveness of the solar tunnel dryer developed and the product dried in the device is superior in quality and also it is compatible with branded products available in the market. The study also determines Acetamide as Phase Key words: Solar Tunnel Dryer, Acetamide as Phase Change Materials, Conversion into Thermal Energy, Thermocouple, and Pyranometer

Control Systems of Rubber Dryer Machinery Components Using Programmable Logic Control (PLC)

Science.gov (United States)

Hendra; Yulianto, A. S.; Indriani, A.; Hernadewita; Hermiyetti

2018-02-01

Application of programmable logic control (PLC) is widely used on the control systems in the many field engineering such as automotive, aviation, food processing and other industries [1-2]. PLC is simply program to control many automatic activity, easy to use, flexible and others. PLC using the ladder program to solve and regulated the control system component. In previous research, PLC was used for control system of rotary dryer machine. In this paper PLC are used for control system of motion component in the rubber dryer machinery. Component of rubber dryer machine is motors, gearbox, sprocket, heater, drying chamber and bearing. Principle working of rubber dryer machinery is wet rubber moving into the drying chamber by sprocket. Sprocket is driven by motors that conducted by PLC to moving and set of wet rubber on the drying chamber. Drying system uses greenhouse effect by making hanger dryer design in the form of line path. In this paper focused on motion control system motors and sensors drying rubber using PLC. The results show that control system of rubber dryer machinery can work in accordance control input and the time required to dry the rubber.

Current development of GHE solar dryer

International Nuclear Information System (INIS)

Kamaruddin Abdullah

2006-01-01

Field tests of the previous GHE solar dryer design had shown that the system can be used effectively to dry various agricultural and marine products. In order to improve further the performance of this dryer, particularly, to reduce dependency on electricity, mechanical energy and on heat generated from non-renewable energy sources, several new prototypes are now in the stage of preliminary testing. These new systems were designed to dry granular products using vibrated drums and for non-granular products such as chili, sliced vegetables and fish products using vibrating racks. The hybrid renewable energy system for drying accommodate Savonius windmill for air moving device as well as vibration generator and simple biomass stove as auxiliary heating unit

Thermophysical Properties of Cold and Vacuum Plasma Sprayed Cu-Cr-X Alloys, NiAl and NiCrAlY Coatings. Part 1; Electrical and Thermal Conductivity, Thermal Diffusivity, and Total Hemispherical Emissivity

Science.gov (United States)

Raj, S. V.

2017-01-01

This two-part paper reports the thermophysical properties of several cold and vacuum plasma sprayed monolithic Cu and Ni-based alloy coatings. Part I presents the electrical and thermal conductivity, thermal diffusivity, and total hemispherical emissivity data while Part II reports the specific heat capacity data for these coatings. Metallic copper alloys, stoichiometric NiAl and NiCrAlY coatings were fabricated by either the cold sprayed or the vacuum plasma spray deposition processes for thermal property measurements between 77 and 1223 K. The temperature dependencies of the thermal conductivities, thermal diffusivities, electrical conductivities and total hemispherical emissivities of these cold and vacuum sprayed monolithic coatings are reported in this paper. The electrical and thermal conductivity data correlate reasonably well for Cu-8%Cr-1%Al, Cu-23%Cr-5%Al and NiAl in accordance with the Wiedemann-Franz (WF) law although a better fit is obtained using the Smith-Palmer relationship. The Lorentz numbers determined from the WF law are close to the theoretical value.

Modeling and simulation of milk emulsion drying in spray dryers

Directory of Open Access Journals (Sweden)

V. S. Birchal

2005-06-01

Full Text Available This work aims at modeling and simulating the drying of whole milk emulsion in spray dryers. Drops and particles make up the discrete phase and are distributed into temporal compartments following their residence time in the dryer. Air is the continuous and well-mixed phase. Mass and energy balances are developed for each phase, taking into account their interactions. Constitutive equations for describing the drop swelling and drying mechanisms as well as the heat and mass transfer between particles and hot air are proposed and analyzed. A set of algebraic-differential equations is obtained and solved by specific numerical codes. Results from experiments carried out in a pilot spray dryer are used to validate the model developed and the numerical algorithm. Comparing the simulated and experimental data, it is shown that the model predicts well the individual drop-particle history inside the dryer as well as the overall outlet air-particle temperature and humidity.

Herbs drying using a heat pump dryer

Energy Technology Data Exchange (ETDEWEB)

Fatouh, M.; Metwally, M.N.; Helali, A.B.; Shedid, M.H. [Department of Mechanical Power Engineering, Faculty of Engineering at El Mattaria, Helwan University, P.O. Box 11718, Masaken El-Helmia, Cairo (Egypt)

2006-09-15

In the present work, a heat pump assisted dryer is designed and constructed to investigate the drying characteristics of various herbs experimentally. R134a is used as a working fluid in the heat pump circuit during the experimental work. Experiments have been conducted on Jew's mallow, spearmint and parsley. The effects of herb size, stem presence, surface load, drying air temperature and air velocity on the drying characteristics of Jew's mallow have been predicted. Experimental results show that a high surface load of 28kg/m{sup 2} yields the smallest drying rate, while the drying air with temperature of 55{sup o}C and velocity of 2.7m/s achieves the largest drying rate. A maximum dryer productivity of about 5.4kg/m{sup 2}h is obtained at the air temperature of 55{sup o}C, air velocity of 2.7m/s and dryer surface load of 28kg/m{sup 2}. It was found that small size herbs without stem need low specific energy consumption and low drying time. Comparison of the drying characteristics of different herbs revealed that parsley requires the lowest specific energy consumption (3684kJ/kg{sub H{sub 2}O}) followed by spearmint (3982kJ/kg{sub H{sub 2}O}) and Jew's mallow (4029kJ/kg{sub H{sub 2}O}). Finally, dryer productivity has been correlated in terms of surface load, drying air velocity and drying air temperature. (author)

30 CFR 77.307 - Thermal dryers; location and installation; general.

Science.gov (United States)

2010-07-01

... where the heat, sparks, flames, or coal dust from the system might cause a fire or explosion. (b... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Thermal Dryers § 77.307 Thermal dryers; location and installation; general...

Hand dryer noise in public restrooms exceeds 80 dBA at 10 ft (3 m

Directory of Open Access Journals (Sweden)

Shari Salzhauer Berkowitz

2015-01-01

Full Text Available High airflow hand dryers are found in many public restrooms today. These dryers offer quick and clean hand drying, and are seen as being an environment-friendly alternative to paper towels. However, many new hand dryers are loud, exposing individuals using the facilities as well as those employees who clean the facilities to potentially dangerous noise. Prolonged exposure to high levels of occupational noise can cause damage to hair cells in the cochlea, resulting in varying degrees of noise-induced hearing loss. This study examined the intensity (in dBA of the noise produced by the air dryers in campus restrooms. Hand dryer peak and average noise was measured with a sound level meter at 2.5 ft, 5 ft, and 10 ft from the dryer. Noise measurements did not decrease as predicted by the inverse-square law, probably because of the reverberative surfaces found in the restrooms. The small sample of hand dryers tested was mostly found to be producing more noise than the manufacturer claimed they would; indeed, none of the dryers would be safe for an 8-h workday exposure. While hand dryers do reduce paper trash, they pose as a different sort of hazard to our environment and population.

Tropical field performance of dual-pass PV tray dryer

Science.gov (United States)

Iskandar, A. Noor; Ya'acob, M. E.; Anuar, M. S.

2017-09-01

Solar Photovoltaic technology has become the preferable solution in many countries around the globe to solve the ever increasing energy demand of the consumers. In line with the consumer need, food processing technology has huge potentials of integration with the renewable energy resources especially in drying process which consumes the highest electricity loads. Traditionally, the solar dryer technology was applied in agriculture and food industries utilizing the sun's energy for drying process, but this is highly dependable on the weather condition and surrounding factors. This work shares some field performance of the new design of portable dual-pass PV tray dryer for drying crops in an enclosed system. The dual-pass PV tray dryer encompass a lightweight aluminium box structure with dimensions of 1.1m (L) x 0.6m (W) x 0.2m (H) and can hold a load capacity of 300g - 3kg of crop depending on the types of the crops. Experiments of field performance monitoring were conducted in October -November 2016 which justifies a considerable reduction in time and crops quality improvement when using the dual-pass PV tray dryer as compared to direct-sun drying.

Cold-rolled sheets production of stainless martensite-ageing steel smelted by vacuum arc and electroslag techniques

Energy Technology Data Exchange (ETDEWEB)

Rivkin, A A; Grishkov, A I; Suslin, A P; Nesterenko, A A; Lola, V N [Tsentral' nyj Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii, Moscow (USSR)

1975-05-01

In cooperation with a number of metallurgical works the production of a high strength sheet stainless maraging steel EHP678 (000KH11N10M2T) has been tested by rolling cylindrical ingots of vacuum arc smelting at the blooming (the mass of rough ingots was 5.1 to 6.0 t, that of cleaned ingots - 3.8 to 5.1 t) or rectangular ingots of electroslag smelting (13 t) at the slabbing. The recommended regimes of heating and deformation are much similar to those used for the steel-KH18N10T. The output of valid cold-rolled sheets proved to be rather low (0.24 t/t for the vacuum arc smelting and 0.30 t/t for the electroslag smelting) mainly due to the losses on cleaning and a considerable portion of wrong-size slabs. The data are presented on the steel-EHP678 properties after various heat treatments. For the production of wide cold-rolled sheets of the steel EHP678 it is recommended to use steelmaking procedure with electroslag smelting including open-hearth melting in arc furnaces, rolling of ingots at the slabbing with heating up to 1260-1280 deg C (hold-up of 4.5 to 5 hrs); electroslag smelting for rectangular section slabs, rolling of ingots of electroslag smelting at the slabbing with their heating up to 1250 deg C (hold-up of 5.5 to 6 hrs), rolling at the 1680-type mill with heating up to 1250-1260 deg C (hold-up of 4 to 4.5 hrs ensuring the rolling temperature after a rough group not below 1100 deg C), quenching of hot-rolled sheets heating up to 920-940 deg C (hold-up of 3 to 3.5 min/mm), shot peening of sheets for descaling (provided the respective equipment is available) with a subsequent short-time pickling in an acid solution and cold rolling with a summary deformation of 35 to 45 %. The steelmaking with the electroslag smelting is much more profitable as regards to the fine technology of number of the main procedures, convenient cooperation of the works and a considerably greater output of the final products out of one ton of the steel produced.

Solar dryer with thermal storage and biomass-backup heater

Energy Technology Data Exchange (ETDEWEB)

Madhlopa, A. [Department of Physics and Biochemical Sciences, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi); Ngwalo, G. [Department of Mechanical Engineering, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi)

2007-04-15

An indirect type natural convection solar dryer with integrated collector-storage solar and biomass-backup heaters has been designed, constructed and evaluated. The major components of the dryer are biomass burner (with a rectangular duct and flue gas chimney), collector-storage thermal mass and drying chamber (with a conventional solar chimney). The thermal mass was placed in the top part of the biomass burner enclosure. The dryer was fabricated using simple materials, tools and skills, and it was tested in three modes of operation (solar, biomass and solar-biomass) by drying twelve batches of fresh pineapple (Ananas comosus), with each batch weighing about 20 kg. Meteorological conditions were monitored during the dehydration process. Moisture and vitamin C contents were determined in both fresh and dried samples. Results show that the thermal mass was capable of storing part of the absorbed solar energy and heat from the burner. It was possible to dry a batch of pineapples using solar energy only on clear days. Drying proceeded successfully even under unfavorable weather conditions in the solar-biomass mode of operation. In this operational mode, the dryer reduced the moisture content of pineapple slices from about 669 to 11% (db) and yielded a nutritious dried product. The average values of the final-day moisture-pickup efficiency were 15%, 11% and 13% in the solar, biomass and solar-biomass modes of operation respectively. It appears that the solar dryer is suitable for preservation of pineapples and other fresh foods. Further improvements to the system design are suggested. (author)

Performances of continuous dryer with inert medium fluidized bed

Directory of Open Access Journals (Sweden)

Arsenijević Zorana Lj.

2008-01-01

Full Text Available A fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies according to the main efficiency criteria, i.e. specific water evaporation rate, specific heat consumption and speci­fic air consumption. A high drying efficiency results from the large con­tact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles leads to nearly isothermal conditions throughout the bed. A fluid bed dryer with inert particles was used for drying of slurries. Experiments were performed in a cylindrical column 215 mm in diameter with glass spheres as inert particles. In this paper, results of drying experi­ments with slurries of Zineb fungicide, copper hydroxide, calcium carbo­nate and pure water used as the feed material are presented. In our fluidized bed we successfully dried a number of other materials such as: fungicides and pesticides (Ziram, Propineb, Mangozeb, copper oxy-chloride, copper oxy-sulphate, Bordeaux mixture, other inorganic compounds (calcium sulphate, cobalt carbonate, electrolytic copper, sodium chloride, and a complex compound (organo-bentonite. The effects of operating conditions on dryer throughput and product quality were investigated. Main performance criteria, i.e. specific water evaporation rate, specific heat consumption and specific air consumption, were quantified. Temperature profile along the bed was mapped, and nearly isothermal conditions were found due to thorough mixing of the particles. Analysis of drying and energy efficiencies as a function of inlet and outlet air temperature difference was performed for deeper insight in dryer behavior and for optimizing dryer design and operation from an energy point of view. A simple mathematical model based on an overall heat balance predicts the dryer performance quite well. The industrial prototype with fluid bed of 0.8 m in diameter and capacity 650 kg of evaporated moisture per

Experimental silo-dryer-aerator for the storage of soybean grains

Directory of Open Access Journals (Sweden)

Paulo C. Coradi

Full Text Available ABSTRACT This study aimed to verify the capacity of silo-dryer-aerator prototype equipment operating as a silo-storage-aerator for soybean quality analysis. Soybeans with water content of 17% (wet basis – w.b. were dried and stored in a silo-dryer-aerator system that was designed using a drying chamber, four independent storage cells, and a static capacity of 164 kg. Another batch of grains was stored in a silo-storage-aerator with a capacity of 1,200 kg. The experiment was set up in a completely randomized factorial 5 × 4 experimental design including five grain batches stored after being dried at 30, 40, and 50 °C (mixed grains were dried at three temperatures in the silo-dryer-aerator cells and one mixed grain batch stored in the silo-storage-aerator system under ambient air conditions for four storage times (zero, one, two, and three months. There was no difference between the grains stored in the silo-dryer-aerator and silo-storage-aerator at the end of the three-month storage in terms of the physico-chemical quality. The storage time associated with drying at 50 °C caused a reduction in the physical-chemical quality of the grains. The silo-dryer-aerator system was presented as a possible alternative to store soybean (Glycine max L. grains.

Machine & electrical double control air dryer for vehicle air braking system

Science.gov (United States)

Zhang, Xuan; Yang, Liu; Wang, Xian Yan; Tan, Xiao Yan; Wang, Wei

2017-09-01

As is known to all, a vehicle air brake system, in which usually contains moisture. To solve the problem, it is common to use air dryer to dry compressed air effectively and completely remove the moisture and oil of braking system. However, the existing air dryer is not suitable for all commercial vehicles. According to the operational status of the new energy vehicles in the initial operating period, the structure design principle of the machine & electric control air dryer is expounded from the aspects of the structure and operating principle, research & development process.

Model-Based Energy Efficiency Optimization of a Low-Temperature Adsorption Dryer

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Low-temperature drying is important for heat-sensitive products, but at these temperatures conventional convective dryers have low energy efficiencies. To overcome this challenge, an energy efficiency optimization procedure is applied to a zeolite adsorption dryer subject to product quality. The

Low cost solar dryer for fish

African Journals Online (AJOL)

Administrator

Department of Electrical and Other Energy Sources, College of Agricultural Engineering and Technology, DBSKKV, ... The average solar energy ranged between 450 - 500 ..... classification and selection of dryers, In Handbook of industrial.

76 FR 22324 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... standards, the current standards for room air conditioners and clothes dryers, and the history of the... Residential Clothes Dryers and Room Air Conditioners AGENCY: Office of Energy Efficiency and Renewable Energy... equipment, including residential clothes dryers and room air conditioners. EPCA also requires the U.S...

Energy Efficient Clothes Dryer with IR Heating and Electrostatic Precipitator

Energy Technology Data Exchange (ETDEWEB)

Weaver, Stanton [GE Global Research, Niskayuna, NY (United States)

2017-12-12

The project goal was to develop a revolutionary energy saving technology for residential clothes drying. The team developed an IR (infrared) heating system and NESP (Nebulizer and Electro-Static Precipitator) for integration into a ventless clothes dryer. The proposed technology addresses two of the major inefficiencies in current electric vented dryers by providing effective energy transfer for the removal of the water and recapture of the vapor latent heat. The IR heaters operating in the mid wave (2.5-10um) are very efficient as they target the 3-micron peak absorption of the water molecule. This allows direct energy absorption, unlike conventional element heaters where heat is transferred by convection. The low power NESP removes water vapor from the exhausted stream and recaptures the latent heat in the ESP (Electro-Static Precipitator) exchanger section. This allows the warm dry air to be recirculated back into the drum for additional efficiency savings. The remaining majority of the dryer hardware stays the same. Summing the efficiency gain from the two subcomponents we anticipated the EF (Efficiency Factor) to exceed the goal of 4.04. EF is obtained by dividing the weight (lbs) of water removed by the energy (kWhr) used, where the test load size is 8.45 lbs of bone dry clothing wetted to 57.5% or 4.8lbs of water, and dried to a remaining moisture content of 2.5-5%. Additional benefits include not having to recondition (heat or cool) the large amounts of make-up air to replace the air exhausted by a vented dryer. It was anticipated that the NESP/heat exchanger would be the most challenging and highest risk element in the program. Therefore, the team focused their efforts during Phase 1 of the program on the design, construction, testing, and optimization of the NESP/heat exchanger. At the end Phase 1, the team compared the performance of the NESP/heat exchanger with the system level requirements and made a Go/No-Go decision on proceeding with the second

The Design And Development Of Solar Maize Dryer With Subsidiary ...

African Journals Online (AJOL)

A solar Dryer with a subsidiary heating source for drying maize seed is designed and constructed. The dryer is made up a solar collector (heat source), the drying chamber (Product storage), and a subsidiary heating source (local oil). The plant when put in operation by expositing it to the solar rays, is capable of attaining a ...

ENERGY STAR Certified Residential Clothes Dryers

Data.gov (United States)

U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.1 ENERGY STAR Program Requirements for Clothes Dryers that are effective as of January...

A greenhouse type solar dryer for small-scale dried food industries: Development and dissemination

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand)

2012-07-01

In this study, a greenhouse type solar dryer for small-scale dried food industries was developed and disseminated. The dryer consists of a parabolic roof structure covered with polycarbonate sheets on a concrete floor. The system is 8.0m in width, 20.0m in length and 3.5m in height, with a loading capacity about 1,000kg of fruits or vegetables. To ensure continuous drying operation, a 100kW-LPG gas burner was incorporated to supply hot air to the dryer during cloudy or rainy days. Nine 15-W DC fans powered by three 50-W PV modules were used to ventilate the dryer. This dryer was installed for a small-scale food industry at Nakhon Pathom in Thailand to produce osmotically dehydrated tomato. To investigate its performance, the dryer was used to dry 3 batches of osmotically dehydrated tomato. Results obtained from these experiments showed that drying air temperatures in the dryer varied from 35 C to 65 C. In addition, the drying time for these products was 2-3 days shorter than that of the natural sun drying and good quality dried products were obtained. A system of differential equations describing heat and moisture transfers during drying of osmotically dehydrated tomato was also developed. The simulated results agreed well with the experimental data. For dissemination purpose, other two units of this type of dryer were constructed and tested at two locations in Thailand and satisfactory results were obtained.

SLUDGE TREATMENT PROJECT KOP DISPOSITION - THERMAL AND GAS ANALYSIS FOR THE COLD VACUUM DRYING FACILITY

International Nuclear Information System (INIS)

Swenson, J.A.; Crowe, R.D.; Apthorpe, R.; Plys, M.G.

2010-01-01

The purpose of this document is to present conceptual design phase thermal process calculations that support the process design and process safety basis for the cold vacuum drying of K Basin KOP material. This document is intended to demonstrate that the conceptual approach: (1) Represents a workable process design that is suitable for development in preliminary design; and (2) Will support formal safety documentation to be prepared during the definitive design phase to establish an acceptable safety basis. The Sludge Treatment Project (STP) is responsible for the disposition of Knock Out Pot (KOP) sludge within the 105-K West (KW) Basin. KOP sludge consists of size segregated material (primarily canister particulate) from the fuel and scrap cleaning process used in the Spent Nuclear Fuel process at K Basin. The KOP sludge will be pre-treated to remove fines and some of the constituents containing chemically bound water, after which it is referred to as KOP material. The KOP material will then be loaded into a Multi-Canister Overpack (MCO), dried at the Cold Vacuum Drying Facility (CVDF) and stored in the Canister Storage Building (CSB). This process is patterned after the successful drying of 2100 metric tons of spent fuel, and uses the same facilities and much of the same equipment that was used for drying fuel and scrap. Table ES-l present similarities and differences between KOP material and fuel and between MCOs loaded with these materials. The potential content of bound water bearing constituents limits the mass ofKOP material in an MCO load to a fraction of that in an MCO containing fuel and scrap; however, the small particle size of the KOP material causes the surface area to be significantly higher. This relatively large reactive surface area represents an input to the KOP thermal calculations that is significantly different from the calculations for fuel MCOs. The conceptual design provides for a copper insert block that limits the volume available to

SLUDGE TREATMENT PROJECT KOP DISPOSITION - THERMAL AND GAS ANALYSIS FOR THE COLD VACUUM DRYING FACILITY

Energy Technology Data Exchange (ETDEWEB)

SWENSON JA; CROWE RD; APTHORPE R; PLYS MG

2010-03-09

The purpose of this document is to present conceptual design phase thermal process calculations that support the process design and process safety basis for the cold vacuum drying of K Basin KOP material. This document is intended to demonstrate that the conceptual approach: (1) Represents a workable process design that is suitable for development in preliminary design; and (2) Will support formal safety documentation to be prepared during the definitive design phase to establish an acceptable safety basis. The Sludge Treatment Project (STP) is responsible for the disposition of Knock Out Pot (KOP) sludge within the 105-K West (KW) Basin. KOP sludge consists of size segregated material (primarily canister particulate) from the fuel and scrap cleaning process used in the Spent Nuclear Fuel process at K Basin. The KOP sludge will be pre-treated to remove fines and some of the constituents containing chemically bound water, after which it is referred to as KOP material. The KOP material will then be loaded into a Multi-Canister Overpack (MCO), dried at the Cold Vacuum Drying Facility (CVDF) and stored in the Canister Storage Building (CSB). This process is patterned after the successful drying of 2100 metric tons of spent fuel, and uses the same facilities and much of the same equipment that was used for drying fuel and scrap. Table ES-l present similarities and differences between KOP material and fuel and between MCOs loaded with these materials. The potential content of bound water bearing constituents limits the mass ofKOP material in an MCO load to a fraction of that in an MCO containing fuel and scrap; however, the small particle size of the KOP material causes the surface area to be significantly higher. This relatively large reactive surface area represents an input to the KOP thermal calculations that is significantly different from the calculations for fuel MCOs. The conceptual design provides for a copper insert block that limits the volume available to

Design and Evaluation of Solar Grain Dryer with a Back-up Heater

OpenAIRE

K.S. Tonui; E.B.K. Mutai; D.A. Mutuli; D.O. Mbuge; K.V. Too

2014-01-01

The aim of the study was to design and construct a solar grain dryer integrated with a simple biomass burner using locally available materials. This was to address the limitations of the natural sun drying for example drying exposure, liability to pests and rodents, over-dependence on sun and escalated cost of mechanical dryers. This became beneficial especially in reducing post-harvest losses as well as helping in the preservation of agricultural product. The dryer is composed of solar colle...

75 FR 27504 - Substantial Product Hazard List: Hand-Held Hair Dryers

Science.gov (United States)

2010-05-17

... immersion during their use. Section 15(a) of the CPSA defines ``substantial product hazard'' to include, a....'' Hand-held hair dryers routinely contain open-coil heating elements that are, in essence, uninsulated..., bathtub, or lavatory). The proposed rule would define ``hand-held hair dryer'' as ``an electrical...

Cold Leak Tests of LHC Beam Screens

CERN Document Server

Collomb-Patton, C; Jenninger, B; Kos, N

2009-01-01

In order to guide the high energy proton beams inside its two 27 km long vacuum rings, the Large Hadron Collider (LHC) at CERN, Geneva, makes use of superconducting technology to create the required magnetic fields. More than 4000 beam screens, cooled at 7 20 K, are inserted inside the 1.9 K beam vacuum tubes to intercept beam induced heat loads and to provide dynamic vacuum stability. As extremely high helium leak tightness is required, all beam screens have been leak tested under cold conditions in a dedicated test stand prior to their installation. After describing the beam screen design and its functions, this report focuses on the cold leak test sequence and discusses the results.

24 CFR 3280.708 - Exhaust duct system and provisions for the future installation of a clothes dryer.

Science.gov (United States)

2010-04-01

...(a)(1) through (5). (c) Provisions for future installation of electric clothes dryers. When wiring is... for the future installation of a clothes dryer. 3280.708 Section 3280.708 Housing and Urban... duct system and provisions for the future installation of a clothes dryer. (a) Clothes dryers. (1) All...

75 FR 7987 - Energy Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public...

Science.gov (United States)

2010-02-23

... Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public Meeting and... conservation standards for residential clothes dryers and room air conditioners; the analytical framework..., Mailstop EE-2J, Public Meeting for Residential Clothes Dryers and Room Air Conditioners, EERE-2007-BT-STD...

[Thermal energy utilization analysis and energy conservation measures of fluidized bed dryer].

Science.gov (United States)

Xing, Liming; Zhao, Zhengsheng

2012-07-01

To propose measures for enhancing thermal energy utilization by analyzing drying process and operation principle of fluidized bed dryers,in order to guide optimization and upgrade of fluidized bed drying equipment. Through a systematic analysis on drying process and operation principle of fluidized beds,the energy conservation law was adopted to calculate thermal energy of dryers. The thermal energy of fluidized bed dryers is mainly used to make up for thermal consumption of water evaporation (Qw), hot air from outlet equipment (Qe), thermal consumption for heating and drying wet materials (Qm) and heat dissipation to surroundings through hot air pipelines and cyclone separators. Effective measures and major approaches to enhance thermal energy utilization of fluidized bed dryers were to reduce exhaust gas out by the loss of heat Qe, recycle dryer export air quantity of heat, preserve heat for dry towers, hot air pipes and cyclone separators, dehumidify clean air in inlets and reasonably control drying time and air temperature. Such technical parameters such air supply rate, air inlet temperature and humidity, material temperature and outlet temperature and humidity are set and controlled to effectively save energy during the drying process and reduce the production cost.

Performance of a Forced-Convection Greenhouse Dryer for Fish Drying

Directory of Open Access Journals (Sweden)

Martunis Martunis

2013-04-01

Full Text Available ABSTRACT. This research present experimental performance of a forced convection greenhouse dryer for drying of fish. The greenhouse dryer was installed at Aceh province, Indonesia. It has a concrete floor with the area of 6×4 m2. The roof of dryer is built in semi-cylindrical shape and covered with transparent polycarbonate sheets. Two axial flow fans powered by a 50-watt solar cell module was used to generate forced convection for ventilating the dryer.To investigate its performance, the dryer was used to dry two batches of fish. The Results showed that to dry 50 kg fish with initial moisture 68 % required 11 hours. Incontrast, to dry the same amount of fish using sun drying take a time about 2 days. The air temperature inside greenhouse dryer at noon in the clear day was 45-55°C. Kinerja Pengering Rumah Kaca Dengan Metode Konveksi Paksa Untuk Pengeringan Ikan ABSTRAK. Penelitian ini memperlihatkan hasil percobaan terhadap kinerja pengering rumah kaca dengan metode konveksi udara secara paksa pada pengeringan ikan. Penelitian pengering rumah kaca ini dilakukan di Propinsi Aceh, Indonesia. Pengering ini berlantaikan beton dengan luas sebesar 6x4 m2. .Atapnya dibuat berbentuk semi-selinder dan ditutup dengan lembaran plastik transparan berbahan polikarbonat. Dua buah kipas dengan aliran udara secara aksial dipasang dengan sumber daya berasal dari panel surya sebesar 50 Watt dan dipakai untuk menghasilkan konveksi udara paksa pada ventilasi pengering. Untuk menginvestigasi kinerja rumah kaca ini, pengering ini digunakan untuk mengeringkan dua tumpukan ikan. Hasilnya menunjukkan bahwa untuk mengeringkan sebanyak 50 kg ikan dengan kadar air awalnya sebesar 68% membutuhkan waktu selama 11 jam. Sebaliknya, dengan menggunakan sinar matahari secara langsung, untuk mengeringkan ikan dengan jumlah yang sama, maka waktu yang dibutuhkan lebih lama yaitu sekitar 2 hari. Suhu udara di dalam rumah pengering tepat pada siang hari yang cerah berkisar antara 45

Investigations of a type 316L steam dryer plate material suffering from IGSCC after few years in BWRs

International Nuclear Information System (INIS)

Autio, J.M.; Ehrnsten, U.; Pakarinen, J.; Mouginot, R.; Cocco, M.

2015-01-01

A steam dryer plate material suffered from intergranular stress corrosion cracking after only one and two years of operation in two BWR plants. Numerous indications were observed on the inner roof plates of the steam dryers adjacent to the support beam welds. The material was Type 316L austenitic stainless steel with carbon content below 0.02%. The material was subjected to detailed investigations using optical microscopy, EBSD/SEM, TEM, hardness and nano-indentation. The material showed macro-segregation through the plate thickness. These bands coincided with the location of delta-ferrite islands indicating non-optimal solution heat treatment. α'-martensite was observed deep in the plate indicating cold deformation after solution annealing. A nonhomogeneous distribution of grain orientation was also observed through the plate thickness. Further, surface deformation, although not extending very deep, was observed using EBSD and surface hardness values above 300 HV when measured using small loads. Although the material fulfills the set requirements, the material characteristics have obviously increased the susceptibility of the material to IGSCC. The paper will discuss the possible role of changes in manufacturing over the years and the challenges in quality definitions in material specifications. (authors)

Experiments on cold trap regeneration by NaH decomposition

International Nuclear Information System (INIS)

McPheeters, C.C.; Skladzien, S.B.; Raue, D.J.

1979-10-01

Cold trap regeneration may be very important in future LMFBRs because of the expected high hydrogen source from the steam generators. This hydrogen precipitates as NaH in the cold trap and may fill the trap within one year of operation. Several methods of cold trap regeneration were considered, but the simplest and least expensive appears to be decomposition of NaH under vacuum at elevated temperatures. Experiments were done to assess the feasibility of this method for cold trap regeneration. Small-scale simulated cold traps (SCT) were located with NaH and NaH plus Na 2 O, and were heated both under vacuum and under a sweep gas at 100 kPa. The evolved hydrogen was converted to water by a CuO bed and collected in a weighting tube

Experiments on cold-trap regeneration by NaH decomposition

International Nuclear Information System (INIS)

McPheeters, C.C.; Skladzien, S.B.; Raue, D.J.

1980-06-01

Cold-trap regeneration may be very important in future LMFBRs because of the expected high hydrogen source from the steam generators. This hydrogen precipitates as NaH in the cold trap and may fill the trap within one year of operation. Several methods of cold-trap regeneration were considered, but the simplest and least expensive appears to be decomposition of NaH under vacuum at elevated temperatures. Experiments were done to assess the feasibility of this method for cold-trap regeneration. Small-scale simulated cold traps (SCT) were loaded with NaH and NaH plus Na 2 O, and were heated both under vacuum and under a sweep gas at 100 kPa. The evolved hydrogen was converted to water by a CuO bed and collected in a weighing tube

Cementitious Spray Dryer Ash-Tire Fiber Material for Maximizing Waste Diversion

Directory of Open Access Journals (Sweden)

Charles E. Riley

2011-01-01

Full Text Available Spray dryer absorber (SDA material, also known as spray dryer ash, is a byproduct of coal combustion and flue gas scrubbing processes that has self-cementing properties similar to those of class C fly ash. SDA material does not usually meet the existing standards for use as a pozzolan in Portland cement concrete due to its characteristically high sulfur content, and thus unlike fly ash, it is rarely put to beneficial use. This paper presents the results of a study with the objective of developing beneficial uses for SDA material in building materials when combined with tire fiber reinforcement originating from a recycling process. Specifically, spray dryer ash was investigated for use as the primary or even the sole binding component in a mortar or concrete. This study differs from previous research in that it focuses on very high contents of spray dryer ash (80 to 100 percent in a hardened product. The overarching objective is to divert products that are normally sent to landfills and provide benefit to society in beneficial applications.

76 FR 971 - Energy Conservation Program for Consumer Products: Test Procedures for Clothes Dryers and Room...

Science.gov (United States)

2011-01-06

.... Detergent Specifications for Clothes Dryer Test Cloth Preconditioning 5. Changes To Reflect Current Usage... conservation standard; (3) updated detergent specifications for clothes dryer test cloth preconditioning; (4... detergent specifications for clothes dryer test cloth preconditioning; (7) update the references to external...

DESIGN AND THERMAL PERFORMANCE OF THE SOLAR BIOMASS HYBRID DRYER FOR CASHEW DRYING

Directory of Open Access Journals (Sweden)

Saravanan Dhanuskodi

2014-12-01

Full Text Available Drying of Cashew nut to remove testa is one of the most energy-intensive processes of cashew nut process industry. For this reason a hybrid dryer consisting of a solar flat plate collector, a biomass heater and a drying chamber is designed and fabricated. 40 kg of Cashew nut with initial moisture of 9 % is used in the experiment. The performance test of the dryer is carried out in two modes of operation: hybrid-forced convection and hybrid-natural convection. Drying time and drying efficiency during these two modes of operation are estimated and compared with the sun drying. The system is capable of attaining drying temperature between 50º and 70ºC. In the hybrid forced drying, the required moisture content of 3% is achieved within 7 hours and the average system efficiency is estimated as 5.08%. In the hybrid natural drying, the required moisture content is obtained in 9 hours and the average system efficiency is 3.17%. The fuel consumption during the drying process is 0.5 kg/hr and 0.75 kg/hr for forced mode and natural mode, respectively. The drying process in the hybrid forced mode of operation is twice faster than the sun drying. The dryer can be operated in any climatic conditions: as a solar dryer on normal sunny days, as a biomass dryer at night time and as a hybrid dryer on cloudy days. Based on the experimental study, it is concluded that the developed hybrid dryer is suitable for small scale cashew nut farmers in rural areas of developing countries.

Heat-pump tumble dryers; Waermepumpen-Tumbler

Energy Technology Data Exchange (ETDEWEB)

Bluemig, N.; Gatter, R.

2004-07-01

Commonly available tumble dryers with air-vented or condenser systems in combination with electrical heating have a high specific energy consumption and never fulfil the requirements for Energy Label Class A (<= 0.55 kWh/kg.). The development of a tumbler with a heat pump system has enabled a reduction of almost 50% in the specific energy consumption. In addition to ecological aspects, this means that a significant reduction in energy costs is achieved as well as a beneficial effect on room climate. Other considerations taken into account in the development of the 6.5 kg tumbler were: (i) Compact modular design; integration of the heat pump in the appliance casing; (ii) Long operating life without clogging-up of the heat exchanger by fluff; (iii) Stable process throughout the drying in ambient temperatures of up to 35 {sup o}C. Process stability in particular presented a tough challenge. The solution came in the form of an additional booster condenser that prevents overheating of the compressor towards the end of the process when only negligible amounts of energy are being carried away as a result of the low residual moisture in the laundry. It proved possible to reduce the specific power consumption to less than 0.4 kWh/kg and the leak rate to less 30 %. Thanks to the compact, modular design, the heat pump could be integrated in a housing which has the same size as a conventional 6.5 kg dryer. Clogging-up of the heat exchanger surfaces with fluff was prevented by a multi-stage cascade filtration system. With this heat pump dryer it has been possible for the very first time to develop to series production and launch an appliance in the up to 6.5 kg category that not only fulfils the requirements of Energy Label Class A but also offers a serious alternative to conventional tumble dryers thanks to its compact design, operating safety and ease of operation. Future development opportunities lie in more cost-effective production of the heat pump module, shortening of

VAC*TRAX vacuum thermal desorption

International Nuclear Information System (INIS)

1994-09-01

Pilot VAC*TRAX treatability tests were conducted on RCRA, TSCA, and RCRA/radioactive mixed wastes, to determine the efficiency in remediating organics' contaminated solids. The process volatilizes organic compounds by indirectly heating the feed material in a vacuum batch dryer and condensing the organics separately from the remaining solids. Contaminants included tetrachloroethene, bis(2-ethylhexyl)phthalate, pentachlorophenol, and PCBs. Treatment specifications were met: a tetrachloroethene removal >99.99% and PCB removal from a starting level of 990 ppM to a final level of 3 , as a uranium simulant; the Mo remained in the treated solids, not transferring to the condensate. In the mixed waste tests, uranium present in a feed soil remained in the soil. Economic viability was demonstrated by achieving excellent treatment on a routine basis with both 4 and 6 hour heating cycles

Beam tube vacuum in future superconducting proton colliders

International Nuclear Information System (INIS)

Turner, W.

1994-10-01

The beam tube vacuum requirements in future superconducting proton colliders that have been proposed or discussed in the literature -- SSC, LHC, and ELN -- are reviewed. The main beam tube vacuum problem encountered in these machines is how to deal with the magnitude of gas desorption and power deposition by synchrotron radiation while satisfying resistivity, impedance, and space constraints in the cryogenic environment of superconducting magnets. A beam tube vacuum model is developed that treats photodesorption of tightly bound H, C, and 0, photodesorption of physisorbed molecules, and the isotherm vapor pressure of H 2 . Experimental data on cold tube photodesorption experiments are reviewed and applied to model calculations of beam tube vacuum performance for simple cold beam tube and liner configurations. Particular emphasis is placed on the modeling and interpretation of beam tube photodesorpiion experiments at electron synchrotron light sources. The paper also includes discussion of the constraints imposed by beam image current heating, the growth rate of the resistive wall instability, and single-bunch instability impedance limits

PIV measurements of flow structures in a spray dryer

DEFF Research Database (Denmark)

Meyer, Knud Erik; Velte, Clara Marika; Ullum, Thorvald

2011-01-01

Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields and dyna......Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields...

Vacuum-insulated catalytic converter

Science.gov (United States)

Benson, David K.

2001-01-01

A catalytic converter has an inner canister that contains catalyst-coated substrates and an outer canister that encloses an annular, variable vacuum insulation chamber surrounding the inner canister. An annular tank containing phase-change material for heat storage and release is positioned in the variable vacuum insulation chamber a distance spaced part from the inner canister. A reversible hydrogen getter in the variable vacuum insulation chamber, preferably on a surface of the heat storage tank, releases hydrogen into the variable vacuum insulation chamber to conduct heat when the phase-change material is hot and absorbs the hydrogen to limit heat transfer to radiation when the phase-change material is cool. A porous zeolite trap in the inner canister absorbs and retains hydrocarbons from the exhaust gases when the catalyst-coated substrates and zeolite trap are cold and releases the hydrocarbons for reaction on the catalyst-coated substrate when the zeolite trap and catalyst-coated substrate get hot.

Review on advanced of solar assisted chemical heat pump dryer for agriculture produce

International Nuclear Information System (INIS)

Fadhel, M.I.; Sopian, K.; Daud, W.R.W.; Alghoul, M.A.

2011-01-01

Over the past three decades there has been nearly exponential growth in drying R and D on a global scale. Improving of the drying operation to save energy, improve product quality as well as reduce environmental effect remained as the main objectives of any development of drying system. A solar assisted chemical heat pump dryer is a new solar drying system, which have contributed to better cost-effectiveness and better quality dried products as well as saving energy. A solar collector is adapted to provide thermal energy in a reactor so a chemical reaction can take place. This reduces the dependency of the drying technology on fossil energy for heating. In this paper a review on advanced of solar assisted chemical heat pump dryer is presented (the system model and the results from experimental studies on the system performance are discussed). The review of heat pump dryers and solar assisted heat pump dryer is presented. Description of chemical heat pump types and the overview of chemical heat pump dryer are discussed. The combination of chemical heat pump and solar technology gives extra efficiency in utilizing energy. (author)

Enhancement of Energy Efficiency and Food Product Quality Using Adsorption Dryer with Zeolite

Directory of Open Access Journals (Sweden)

Moh Djaeni

2013-06-01

Full Text Available Drying is a basic operation in wood, food, pharmaceutical and chemical industry. Currently, several drying methods are often not efficient in terms of energy consumption (energy efficiency of 20-60% and have an impact on product quality degradation due to the introduction of operational temperature upper 80oC. This work discusses the development of adsorption drying with zeolite to improve the energy efficiency as well as product quality. In this process, air as drying medium is dehumidified by zeolite. As a result humidity of air can be reduced up to 0.1 ppm. So, for heat sensitive products, the drying process can be performed in low or medium temperature with high driving force. The study has been conducted in three steps: designing the dryer, performing laboratory scale equipment (tray, spray, and fluidised bed dryers with zeolite, and evaluating the dryer performance based on energy efficiency and product quality. Results showed that the energy efficiency of drying process is 15-20% higher than that of conventional dryer. In additon, the dryer can speed up drying time as well as retaining product quality.

Usage of Heat Pump Dryer in Food Drying Process and Apple Drying Application

Directory of Open Access Journals (Sweden)

Gökhan Gürlek

2015-12-01

Full Text Available In Turkey, drying is achieved natural method by spreading out the material on the ground. In this way, there are many disadvantages like low quality and hygienic problems. The resulting loss of food quality in the dried products may have effect negatively trade potential and economical worth. For preventing the deterioration of the materials different types of drying methods have been developed. Low energy consumption applications are important for drying industry besides high product quality. For this purpose, heat pump dryer is gaining importance day by day in drying applications. In this study, the working principle of the heat pump dryer, heat pump types in the drying process and the heat pump dryer performance criteria will be considered. An example of application will be described using obtained results from apple drying operation that is conducted in the heat pump dryer.

Decontamination in the Electron Probe Microanalysis with a Peltier-Cooled Cold Finger.

Science.gov (United States)

Buse, Ben; Kearns, Stuart; Clapham, Charles; Hawley, Donovan

2016-10-01

A prototype Peltier thermoelectric cooling unit has been constructed to cool a cold finger on an electron microprobe. The Peltier unit was tested at 15 and 96 W, achieving cold finger temperatures of -10 and -27°C, respectively. The Peltier unit did not adversely affect the analytical stability of the instrument. Heat conduction between the Peltier unit mounted outside the vacuum and the cold finger was found to be very efficient. Under Peltier cooling, the vacuum improvement associated with water vapor deposition was not achieved; this has the advantage of avoiding severe degradation of the vacuum observed when warming up a cold finger from liquid nitrogen (LN2) temperatures. Carbon contamination rates were reduced as cooling commenced; by -27°C contamination rates were found to be comparable with LN2-cooled devices. Peltier cooling, therefore, provides a viable alternative to LN2-cooled cold fingers, with few of their associated disadvantages.

Numerical analysis on centrifugal compressor with membrane type dryer

Science.gov (United States)

Razali, M. A.; Zulkafli, M. F.; Mat Isa, N.; Subari, Z.

2017-09-01

Moisture content is a common phenomenon in industrial processes especially in oil and gas industries. This contaminant has a lot of disadvantages which can lead to mechanical failure DEC (Deposition, Erosion & Corrosion) problems. To overcome DEC problem, this study proposed to design a centrifugal compressor with a membrane type dryer to reduce moisture content of a gas. The effectiveness of such design has been analyzed in this study using Computational Fluid Dynamics (CFD) approach. Numerical scheme based on multiphase flow technique is used in ANSYS Fluent software to evaluate the moisture content of the gas. Through this technique, two kind of centrifugal compressor, with and without membrane type dryer has been tested. The results show that the effects of pressure on dew point temperature of the gas change the composition of its moisture content, where high value lead more condensation to occur. However, with the injection of cool dry gas through membrane type dryer in the centrifugal compressor, the pressure and temperature of moisture content as well as mass fraction of H2O in centrifugal compressor show significant reduction.

Conceptual design of pilot scale solar dryer for seaweeds

International Nuclear Information System (INIS)

Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Roche-Delgado, Liset; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Hernández-Touset, Juan Pedro; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >García-Rodríguez, Agustín

2017-01-01

Drying algal biomass with the use of solar radiation is an economical and environmentally compatible option. The aim of this work was to design an indirect solar dryer with natural air circulation for seaweeds drying. The equipment supports discrete quantities of wet biomass and is protected from environmental situations that may damage the product; it does not need electricity to operate and the construction and operating costs are low. This comprises a collector made of copper plates for air circulation, heated by solar radiation, a glass cover and drying trays with a wooden structure. The dryer was designed to obtain 0, 3 kg / day of dry biomass. The methodology allows construction and operation of a flexible solar dryer in different operating conditions for research on seaweeds. Correspondingly with environmental and operating conditions the design included estimation of drying time, the determination of drying area, number of trays, air flow from the collector to the trays, collector sizing; heat transfer area, temperature reached by air and collector efficiency. (author)

Natural convection solar dryer with biomass back-up heater

Energy Technology Data Exchange (ETDEWEB)

Bena, B.; Fuller, R.J. [University of Melbourne (Australia). Faculty of Engineering

2002-07-01

A direct-type natural convection solar dryer and a simple biomass burner have been combined to demonstrate a drying technology suitable for small-scale processors of dried fruits and vegetables in non-electrified areas of developing countries. From a series of evaluation trials of the system, the capacity of the dryer was found to be 20-22kg of fresh pineapple arranged in a single layer of 0.01-m-thick slices. The overall drying efficiency of the unit was calculated to be {approx} 9%. During the same trial, the drying efficiency of the solar component alone was found to be 22%. Other trials estimated the efficiency of the burner in producing useful heat for drying to be 27%. Key features of the biomass burner were found to be the addition of thermal mass on the upper surface, an internal baffle plate to lengthen the exhaust gas exit path and a variable air inlet valve. Further modifications to further improve the performance of both the solar and biomass components of the dryer are suggested. (author)

Thin layer drying characteristics of curry leaves (Murraya koenigii in an indirect solar dryer

Directory of Open Access Journals (Sweden)

Vijayan Selvaraj

2017-01-01

Full Text Available In this work, the thin layer drying characteristics of curry leaves (Murraya koenigii has been studied in an indirect forced convection solar dryer with constant air mass flow rate of 0.0636 kg/s. Twelve thin layer drying models were tested for its suitability to describe the drying characteristics of curry leaves. The dryer has reduced the initial moisture content of curry leaves from 67.3% (wet basis to the final moisture content of 4.75% (wet basis in 3.5 hours. The pickup efficiency of indirect solar dryer for drying curry leaves was varied between 4.9% and 23.02%. Based on the statistical parameters, the Modified Henderson and Pabis model and Wang and Singh model were selected for predicting the drying characteristics of curry leaves. The payback period for the solar dryer was evaluated as 8 months, which is found to be much lower when compared with the entire life span of 15 years. The payback evaluation confirms that the solar dryer is economically viable in rural applications.

Design, Development and Performance Evaluation of a Small Scale Solar Assisted Paddy Dryer for on Farm Processing

Directory of Open Access Journals (Sweden)

Sidrah Ashfaq

2016-04-01

Full Text Available With the continued escalation in population growth and the expansion of international food trade and demand of high quality product for food security at low cost has created considerable interest in the development of new post-harvest technologies. This is particularly important for developing countries where post-harvest losses of cereals are between 10-20% and of fruits and vegetables as high as 20- 100% A new solar assisted paddy dryer with central air distribution model (along the length of drying chamber has been developed. Due to this distinct feature of the dryer high drying rate was achieved during the drying processes .Other components of the dryer are perforated drying chamber, blower and flat plat solar air collector. Dryer was evaluated using 100kg of freshly harvested paddy at 23.78% moisture content (wb. Performance evaluation results showed that the mean drying rate of the solar assisted paddy dryer was 0.87kg/hr per for every 100kg, whereas 0.46kg/hr was the sun drying rate comparatively. The faster drying rate of the dryer reveals its suability to dry the paddy for its safe storage moisture content rapidly. By using the solar assisted paddy dryer, approximately 50% saving in time was also achieved as compared with the traditional sun drying method. Solar assisted paddy dryer took 10hr for drying the 100kg paddy up to 14%, while sun drying method dried paddy up to 13.89% in 19 hours. Cost analysis also showed that, by using solar assisted paddy dryer we candry good quality paddy at low cost as compared with the open sun drying method. For development of agriculture in the rural areas, commercial size of the solar assisted paddy dryer can be amplified and produced at community level.

Application of Constrained Linear MPC to a Spray Dryer

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we develop a linear model predictive control (MPC) algorithm for control of a two stage spray dryer. The states are estimated by a stationary Kalman filter. A non-linear first-principle engineering model is developed to simulate the spray drying process. The model is validated against...... experimental data and able to precisely predict the temperatures, the air humidity and the residual moisture in the dryer. The MPC controls these variables to the target and reject disturbances. Spray drying is a cost-effective method to evaporate water from liquid foods and produces a free flowing powder...

Energetic and economic optimization of solar tunnel dryers with a photovoltaic driven fan

International Nuclear Information System (INIS)

Muehlbauer, W.; Mayer, R.A.; Esper, A.; Reisinger, L.; Linckh, G.; Hensel, O.

1992-02-01

In the recent years the solar tunnel dryer has been used successfully for drying several agricultural products in tropical and subtropical countries. Up to now the dissemination has been limited to electrified areas. Objective of this work has been the improvement of the thermal performance of the tunnel dryer due to a optimization of the plastic film solar air heater as well as optimization work in point of fluid dynamic view to reduce the power requirement of the blower. To improve the efficiency of the blower optimization work had been done by investigating several blower wheels, dc-motors and actuation systems. A PV-System was designed according to these requirements to test the long term behaviour. The remarkable features of the newly designed solar tunnel dryer are the low power requirement for driving the blower and a high efficiency of the actuation. In the range of a power requirement of 80 - 100 W a blower with an efficiency of 48% is now available. The theoretical power requirement of the solar tunnel dryer could be reduced to 11 W. From economic point of view the use of the solar tunnel dryer is possible. (orig.) With 3 refs., 15 tabs., 49 figs [de

VAC*TRAX vacuum thermal desorption

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-09-01

Pilot VAC*TRAX treatability tests were conducted on RCRA, TSCA, and RCRA/radioactive mixed wastes, to determine the efficiency in remediating organics` contaminated solids. The process volatilizes organic compounds by indirectly heating the feed material in a vacuum batch dryer and condensing the organics separately from the remaining solids. Contaminants included tetrachloroethene, bis(2-ethylhexyl)phthalate, pentachlorophenol, and PCBs. Treatment specifications were met: a tetrachloroethene removal >99.99% and PCB removal from a starting level of 990 ppM to a final level of <1 ppM. One test run was spiked with MoO{sub 3}, as a uranium simulant; the Mo remained in the treated solids, not transferring to the condensate. In the mixed waste tests, uranium present in a feed soil remained in the soil. Economic viability was demonstrated by achieving excellent treatment on a routine basis with both 4 and 6 hour heating cycles.

A dedicated on-line detecting system for auto air dryers

Science.gov (United States)

Shi, Chao-yu; Luo, Zai

2013-10-01

According to the correlative automobile industry standard and the requirements of manufacturer, this dedicated on-line detecting system is designed against the shortage of low degree automatic efficiency and detection precision of auto air dryer in the domestic. Fast automatic detection is achieved by combining the technology of computer control, mechatronics and pneumatics. This system can detect the speciality performance of pressure regulating valve and sealability of auto air dryer, in which online analytical processing of test data is available, at the same time, saving and inquiring data is achieved. Through some experimental analysis, it is indicated that efficient and accurate detection of the performance of auto air dryer is realized, and the test errors are less than 3%. Moreover, we carry out the type A evaluation of uncertainty in test data based on Bayesian theory, and the results show that the test uncertainties of all performance parameters are less than 0.5kPa, which can meet the requirements of operating industrial site absolutely.

Critical Point Dryer: Tousimis 916B Series C

Data.gov (United States)

Federal Laboratory Consortium — Description:CORAL Name: Critical Point DryerThis system utilizes CO 2to dry fragile suspended and floating structures Specifications / Capabilities:Wafer size up to...

Biogas utilization for drying sweet potato chips by using infrared dryer

Science.gov (United States)

Sriharti, Rahayuningtyas, Ari; Susanti, Novita Dwi; Sitompul, Rislima Febriani

2017-11-01

This study aims to utilize biogas, that produced from organic waste, as fuel for infrared dryers. The digester was dome type, which made from fiberglass, 5.5 m3 capacities, gas container made from soft PVC, 5.6 m3 capacities. The infrared dryer was household scale which have dimension 2000 mm x 2000 mm x 2000 mm, it is consist of 2 racks, which have size 1500 mm x 500 mm x 1400 mm, and consist of 44 baking pans (600 mm X 400 mm x 30 mm), the dryer has 36 kg of capacity. The parameters observed include ambient temperature, temperature inside the digester, pH value, biogas production, drying room temperature, moisture content of sweet potato and biogas consumption for drying. Infrared dryer is used to dry the sweet potato slices thickness of 2 mm with total amount 12 kg, at room temperature dryer ± 60 °C. The results showed that the average biogas production was 1.335 m3 per day, at a temperature of 26 - 35 °C and the neutral pH value was 6.99 - 7.7. 12 kg of sweet potato sliced dried for 4 hours, the initial moisture content of 79.68 % decreased to 8.98 %, the consumption of biogas used 4,952 m3. The final result of drying process of sweet potato slices of 3.5 kg, there was a shrinkage of 70.83 %. Characterization of sweet potato slices is 3 % protein, 0,6 % fat, 94 % carbohydrate and 2 % ash. These sweet potato can be used as flour for cookies and cake raw materials, the use of sweet potato flour can reach 50 - 100 %.

Nd:YAG transparent ceramics fabricated by direct cold isostatic pressing and vacuum sintering

Science.gov (United States)

Ge, Lin; Li, Jiang; Zhou, Zhiwei; Liu, Binglong; Xie, Tengfei; Liu, Jing; Kou, Huamin; Shi, Yun; Pan, Yubai; Guo, Jingkun

2015-12-01

The sintering behavior of neodymium doped yttrium aluminum garnet (Nd:YAG) ceramics was investigated on the basis of densification trajectory, microstructure evolution and transmittance. Nd:YAG ceramics with in-line transmittance of 83.9% at 1064 nm and 82.5% at 400 nm were obtained by direct cold isostatic pressing (CIP) at 250 MPa and solid-state reactive sintering at 1790 °C for 30 h under vacuum. Compared with the porosity and the average pore diameter of the sample from uniaxial dry-pressing followed by CIP, those from direct CIP are much smaller. The samples pressed at 250 MPa were sintered from 1500 °C to 1750 °C for 0.5-20 h to study their sintering behavior. At the temperature higher than 1500 °C, pure YAG phase is formed, followed by the densification and grain growth process. The relative density and the grain size increase with the increase of sintering time and temperature, and the sintering behavior is more sensitive to temperature than holding time. The mechanism controlling densification and grain growth at sintering temperature of 1550 °C is grain boundary diffusion.

MD Simulation on Collision Behavior Between Nano-Scale TiO₂ Particles During Vacuum Cold Spraying.

Science.gov (United States)

Yao, Hai-Long; Yang, Guan-Jun; Li, Chang-Jiu

2018-04-01

Particle collision behavior influences significantly inter-nano particle bonding formation during the nano-ceramic coating deposition by vacuum cold spraying (or aerosol deposition method). In order to illuminate the collision behavior between nano-scale ceramic particles, molecular dynamic simulation was applied to explore impact process between nano-scale TiO2 particles through controlling impact velocities. Results show that the recoil efficiency of the nano-scale TiO2 particle is decreased with the increase of the impact velocity. Nano-scale TiO2 particle exhibits localized plastic deformation during collision at low velocities, while it is intensively deformed by collision at high velocities. This intensive deformation promotes the nano-particle adhesion rather than rebounding off. A relationship between the adhesion energy and the rebound energy is established for the bonding formation of the nano-scale TiO2 particle. The adhesion energy required to the bonding formation between nano-scale ceramic particles can be produced by high velocity collision.

Design, development and performance testing of a new natural convection solar dryer

Energy Technology Data Exchange (ETDEWEB)

Pangavhane, D.R. [K.K. Wagh College of Engineering, Nashik (India). Department of Mechanical Engineering; Sawhney, R.L.; Sarsavadia, P.N. [Devi Ahilya Vishwa Vidhyalaya, Indore (India). School of Energy and Environmental Studies

2002-06-01

Mechanical drying of agricultural products is an energy consuming operation in the post-harvesting technology. Greater emphasis is given to using solar energy sources in this process due to the high prices and shortages of fossil fuels. For these purposes, a new natural convection solar dryer consisting of a solar air heater and a drying chamber was developed. This system can be used for drying various agricultural products like fruits and vegetables. In this study, grapes were successfully dried in the developed solar dryer. The qualitative analysis showed that the traditional drying, i.e. shade drying and open sun drying, dried the grapes in 15 and 7 days respectively, while the solar dryer took only 4 days and produced better quality raisins. (author)

Development of a Mini-Freeze Dryer for Material-Sparing Laboratory Processing with Representative Product Temperature History.

Science.gov (United States)

Obeidat, Wasfy M; Sahni, Ekneet; Kessler, William; Pikal, Michael

2018-02-01

The goal of the work described in this publication was to evaluate a new, small, material-sparing freeze dryer, denoted as the "mini-freeze dryer or mini-FD", capable of reproducing the product temperature history of larger freeze dryers, thereby facilitating scale-up. The mini-FD wall temperatures can be controlled to mimic loading procedures and dryer process characteristics of larger dryers. The mini-FD is equipped with a tunable diode laser absorption spectroscopy (TDLAS) water vapor mass flow monitor and with other advanced process analytical technology (PAT) sensors. Drying experiments were performed to demonstrate scalability to larger freeze dryers, including the determination of vial heat transfer coefficients, K v . Product temperature histories during K v runs were evaluated and compared with those obtained with a commercial laboratory-scale freeze dryer (LyoStar II) for sucrose and mannitol product formulations. When the mini-FD wall temperature was set at the LyoStar II band temperature (- 20°C) to mimic lab dryer edge vials, edge vial drying in the mini-FD possessed an average K v within 5% of those obtained during drying in the LyoStar II. When the wall temperature of the mini-FD was set equal to the central vial product temperature, edge vials behaved as center vials, possessing a K v value within 5% of those measured in the LyoStar II. During both K v runs and complete product freeze drying runs, the temperature-time profiles for the average edge vials and central vial in the mini-FD agreed well with the average edge and average central vials of the LyoStar II.

Steam generator with integral downdraft dryer

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

The effects of atmospheric pressure cold plasma treatment on microbiological, physical-chemical and sensory characteristics of vacuum packaged beef loin.

Science.gov (United States)

Bauer, A; Ni, Y; Bauer, S; Paulsen, P; Modic, M; Walsh, J L; Smulders, F J M

2017-06-01

Effects on vacuum packaged and non-packaged beef longissimus samples exposed to atmospheric cold plasma (ACP) generated at different powers were studied over a 10day period of vacuum-, and a subsequent 3day period of aerobic storage. Exposure of non-covered beef samples under high power ACP conditions resulted in increased a*, b*, Chroma and Hue values, but ACP treatment of packaged loins did not impact colour (L*, a*, b*, Chroma, Hue), lipid peroxidation, sarcoplasmic protein denaturation, nitrate/nitrite uptake, or myoglobin isoform distribution. Colour values measured after 3days of aerobic storage following unpackaging (i.e. 20days post-mortem) were similar and all compliant with consumer acceptability standards. Exposure to ACP of the polyamide-polyethylene packaging film inoculated with Staphylococcus aureus, Listeria monocytogenes and two Escherichia coli strains resulted in >2 log reduction without affecting the integrity of the packaging matrix. Results indicate that ACP can reduce microbial numbers on surfaces of beef packages without affecting characteristics of the packaged beef. Copyright © 2017 Elsevier Ltd. All rights reserved.

PERFORMANCE ASSESSMENT OF SOLAR DRYER WITH INDIRECT HEATING

Directory of Open Access Journals (Sweden)

Boryana Brashlyanova

2014-03-01

Full Text Available The performed tests were designed to identify and analyze the parameters of drying in a authors model solar dryer. They to be the basis for constructing of an improved model. Drying was carried out in a pilot model solar dryer with prunes in two cycles. Both samples were run under steady sunshine in outdoor air temperature ranging between 20-22°C in the morning and 33-35°C in the early afternoon hours. Depending on the ambient conditions, the drying temperature was found in the range of 30 to 50°C. The dried samples had a water activity Aw> 0.9, due to which the storage is at -18°C. The duration of the drying process of prunes was inconstant and lasted from 2 to 3 days, depending on the final moisture content of the product and the external temperature, humidity, and intensity of solar radiation. The obtained two products intermediate moisture prunes, in addition to direct human consumption could be used as a base for incorporation into other products. Prunes with intermediate moisture content 40% could be consumed directly at ambient temperature or after freezing and tempering at -6 to -5ºC. Based on the established parameters we are to design and produce an improved solar dryer model that allows better utilization of heat and shortening the process duration.

Development of heat pump and infrared-convective dryer and performance analysis for stale bread drying

International Nuclear Information System (INIS)

Aktaş, Mustafa; Şevik, Seyfi; Aktekeli, Burak

2016-01-01

Highlights: • Investigation of stale bread drying behaviors by developing the HPD and IRD. • New techniques for the HP and IR dryers are proposed and found to be efficient. • Evaluations on potential uses low temperature applications of the dryers were reported. • 35.6% of energy saving was provided by heat recovery device. • The overall system efficiency of HPD was calculated as 13–60%. - Abstract: This experimental study aims to develop a heat pump dryer (HPD) and an infrared dryer (IRD) also the comparative empirical analyses of these two methods and to analyze the drying kinetic of stale bread sliced 15 mm thickness and effectiveness on the drying kinetics of the stale bread of dryers. Dryers have been developed by using different techniques such as heat recovery unit, proportional control (PC) of drying air temperature, simultaneous control of the relative humidity–temperature–air flow rate, water cycle dehumidifier and closed-loop cycle to increase the drying efficiency of industrial drying applications. The highest coefficient of performance of the whole heat pump system (COP_w_s_,_H_P) was calculated as 3.7 and drying efficiencies of the IRD and HPD systems were calculated as 39% and 25%, respectively. When the HPD and IRD systems were compared in terms of drying time and energy consumption, it was observed that the IRD system did not only shortened the drying time up to 69%, but also decreased the energy consumption of the system by 43.2%. Based on the obtained results the effective moisture diffusivity (D_e) was calculated in the range from 8.3 × 10"−"8 to 3.2 × 10"−"7 m"2/s and mass transfer coefficient (h_m) was varied from 1.17 × 10"−"5 to 4.52 × 10"−"5 m/s. It was concluded that both dryers have significant effect in reduction of water content; the relative humidity controlled HPD can be applied efficiently for dryers and the dried stale bread can be reused as bread crumb by food industry.

Slurry spray distribution within a simulated laboratory scale spray dryer

International Nuclear Information System (INIS)

Bertone, P.C.

1979-01-01

It was found that the distribution of liquid striking the sides of a simulated room temperature spray dryer was not significantly altered by the choice of nozles, nor by a variation in nozzle operating conditions. Instead, it was found to be a function of the spray dryer's configuration. A cocurrent flow of air down the drying cylinder, not possible with PNL's closed top, favorably altered the spray distribution by both decreasing the amount of liquid striking the interior of the cylinder from 72 to 26% of the feed supplied, and by shifting the zone of maximum impact from 1.0 to 1.7 feet from the nozzle. These findings led to the redesign of the laboratory scale spray dryer to be tested at the Savannah River Plant. The diameter of the drying chamber was increased from 5 to 8 inches, and a cocurrent flow of air was established with a closed recycle. Finally, this investigation suggested a drying scheme which offers all the advantages of spray drying without many of its limitations

Cold cathodes on ultra-dispersed diamond base

International Nuclear Information System (INIS)

Alimova, A.N.; Zhirnov, V.V.; Chubun, N.N.; Belobrov, P.I.

1998-01-01

Prospects of application of nano diamond powders for fabrication of cold cathodes are discussed.Cold cathodes based on silicon pointed structures with nano diamond coatings were prepared.The deposition technique of diamond coating was dielectrophoresis from suspension of nano diamond powder in organic liquids.The cathodes were tested in sealed prototypes of vacuum electronic devices

Performance Analysis of a Solar Dryer Equipped with a Recycling Air System and Desiccant Chamber

Directory of Open Access Journals (Sweden)

M.H Aghkhani

2013-09-01

Full Text Available Drying is a high energy consuming process. Solar drying is one of the most popular methods for dehydration of agricultural products. In the present study, the performance of a forced convection solar dryer equipped with recycling air system and desiccant chamber was investigated. The solar dryer is comprised of solar collector, drying chamber, silica jell desiccant chamber, air ducts, fan and measuring and controlling system. Drying rate and energy consumption in three levels of air temperature (40, 45 and 50 oC and two modes of drying (with recycling air and no-recycling with open duct system were measured and compared. The results showed that increasing the drying air temperature decreased the drying time and increased the energy consumption in the mode of non-recycling air system. The dryer efficiency and drying rate were better in the mode of recycling air system than open duct system. The highest dryer efficiency was obtained from drying air temperature of 50 oC and the mode of recycling air system. In general, the efficiency of solar collector and the highest efficiency of the dryer were 0.34 and 0.41, respectively.

Performance of a chevron steam dryer for removal of lead-bismuth droplets

International Nuclear Information System (INIS)

Dostal, Vaclav; Yusibani, Elin; Takahashi, Minoru

2005-01-01

An analysis was performed of a chevron type steam dryer with a trap for the removal of lead-bismuth droplets from steam leaving the Water Boiling Direct Contact Lead or Lead-Bismuth Cooled Reactor. The Lagrangian method was used and is described here. The steam flow field was developed using a CFD code FrontFlow/Red. The simulated dryer performance results were compared to a simple theoretical model from literature. The simulation shown that droplets down to 6 microns in diameter can be completely removed by the steam dryer, which is better than reported earlier in literature. A discrepancy with the theoretical model was found for larger droplets (5 to 10 microns in diameter), where the theoretical model predicted lower removal efficiency. The discrepancy is attributed to be installation of the trap, which is not included in this theoretical model. Some droplets of 1 and 0.5 microns were removed in the dryer as well, which indicates the potential for the fine droplet removal if the trap design is carefully optimized. The investigation of the effect of initial droplet velocity shown that the removal efficiency increases with the increase of the positive velocity components. For larger droplets the effect of initial velocity was found to be minuscule. (author)

Performance studies of solar tunnel dryer for drying aonla (Embilica Officinalis) pulp

International Nuclear Information System (INIS)

Seveda, M. S.

2012-01-01

A solar tunnel dryer was constructed and evaluated the performance for drying aonla pulp. The dryer consists of a transparent UV stabilized plastic covered solar collector cum drying unit. Evaluation parameters are air temperature, solar insolation, moisture content, relative humidity and airflow rate. A minimum of 111.18 m 2 solar collector area is required to dry a batch 1000 kg aonla pulp in 16 hours (two days drying period). The initial and final moisture content considered were 424.93 and 10.08% dry basis, respectively. It was observed that on an average 43 per cent of higher temperature was obtained in solar tunnel dryer over the ambient temperature. The results obtained during the test period denoted that the maximum gained energy occurred at 13 o'clock hour and then gradually declined since the maximum solar radiation occurred at this time. (author)

Tritium isotopic exchange in air detritiation dryers

International Nuclear Information System (INIS)

Everatt, A.E.; Johnson, R.E.; Senohrabek, J.A.; Shultz, C.M.

1989-02-01

Isotopic exchange between tritiated and non-tritiated water species in a molecular sieve bed has been demonstrated. At high humidities (+6 degrees Celsius dew point) the rate of tritium isotopic exchange in a 2.4 L molecular sieve bed has been demonstrated to be at least 50% of published exchange rates. In an industrial-sized air detritiation dryer, utilizing the pretreatment technique of H 2 O steam washing to elute the residual tritium, a DF of 12 600 has been demonstrated when operating at an inlet vapor tritium concentration of 14 Ci/kg and at inlet and outlet dew points of 4.8 and -54 degrees Celsius, respectively. In the NPD dryer bed studied, which was not optimally designed for full benefit from isotopic exchange, at least one order of magnitude in additional detritiation is attributed to isotopic exchange in the unsaturated zone. The technique of eluting the residual tritium from an industrial sized bed by H 2 O washing at high temperature, high humidity and low bed loading has been demonstrated to be a fast and effective way of removing tritium from a molecular sieve bed during regeneration. The isotopic exchange model accurately predicted the exchange between tritiated and non-tritiated water species in a molecular sieve bed where there is no net adsorption or desorption. The model's prediction of the tritium breakthrough trend observed in the NPD tests was poor; however, a forced fit can be achieved if the exchange rates in the MTZ and the unsaturated zone are manipulated. More experiments are needed to determine the relative rates of tritium exchange in the saturated, mass transfer, and unsaturated zones of a dryer bed

Simple, reliable, and nondestructive method for the measurement of vacuum pressure without specialized equipment.

Science.gov (United States)

Yuan, Jin-Peng; Ji, Zhong-Hua; Zhao, Yan-Ting; Chang, Xue-Fang; Xiao, Lian-Tuan; Jia, Suo-Tang

2013-09-01

We present a simple, reliable, and nondestructive method for the measurement of vacuum pressure in a magneto-optical trap. The vacuum pressure is verified to be proportional to the collision rate constant between cold atoms and the background gas with a coefficient k, which can be calculated by means of the simple ideal gas law. The rate constant for loss due to collisions with all background gases can be derived from the total collision loss rate by a series of loading curves of cold atoms under different trapping laser intensities. The presented method is also applicable for other cold atomic systems and meets the miniaturization requirement of commercial applications.

A study of particle motion in rotary dryer

Directory of Open Access Journals (Sweden)

M. H. Lisboa

2007-09-01

Full Text Available The purpose of this work was to study the performance of a rotary dryer in relation to number of flights. In this work an equationing was proposed to calculate the area used by the solids in two-segment flights of with any angle between the segments. From this area, the flight holdup and the length of fall of the particles were calculated for different angle positions and the results obtained were compared to experimental values. The results show an increase in dryer efficiency with the increase in number of flights up to a limit value, for ideal operational conditions. The experimental data on average residence time were compared to results obtained by calculations using equations proposed in the literature. The equation proposed for predicting flight holdup and length of fall of particles generated very accurate estimations.

Performance of a solar dryer using hot air from roof-integrated solar collectors for drying herbs and spices

Energy Technology Data Exchange (ETDEWEB)

Janjai, S.; Tung, P. [Silpakorn University, Pathom (Thailand). Dept. of Physics

2005-11-01

A solar dryer for drying herbs and spices using hot air from roof-integrated solar collectors was developed. The dryer is a bin type with a rectangular perforated floor. The bin has a dimension of 1.0 m x 2.0 m x 0.7 m. Hot air is supplied to the dryer from fiberglass-covered solar collectors, which also function as the roof of a farmhouse. The total area of the solar collectors is 72 m{sup 2}. To investigate its performance, the dryer was used to dry four batches of rosella flowers and three batches of lemon-grasses during the year 2002-2003. The dryer can be used to dry 200 kg of rosella flowers and lemon-grasses within 4 and 3 days, respectively. The products being dried in the dryer were completely protected from rains and insects and the dried products are of high quality. The solar air heater has an average daily efficiency of 35% and it performs well both as a solar collector and a roof of a farmhouse. (author)

Study on effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans

Directory of Open Access Journals (Sweden)

Sari Farah Dina

2015-03-01

Full Text Available The main objective is to assess effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans. Two type of desiccants were tested, molecular sieve 13× (Na86 [(AlO286·(SiO2106]·264H2O as an adsorbent type and CaCl2 as an absorbent type. The results revealed that during sunshine hours, the maximum temperature within the drying chamber varied from 40 °C to 54 °C. In average, it was 9–12 °C higher than ambient temperature. These temperatures are very suitable for drying cocoa beans. During off-sunshine hours, humidity of air inside the drying chamber was lower than ambient because of the desiccant thermal storage. Drying times for intermittent directs sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorbent were 55 h, 41 h, and 30 h, respectively. Specific energy consumptions for direct sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorber were 60.4 MJ/kg moist, 18.94 MJ/kg moist, and 13.29 MJ/kg moist, respectively. The main conclusion can be drawn here is that a solar dryer integrated with desiccant thermal storage makes drying using solar energy more effective in term of drying time and specific energy consumption.

Window-assisted nanosphere lithography for vacuum micro-nano-electronics

International Nuclear Information System (INIS)

Li, Nannan; Pang, Shucai; Yan, Fei; Chen, Lei; Jin, Dazhi; Xiang, Wei; Zhang, De; Zeng, Baoqing

2015-01-01

Development of vacuum micro-nano-electronics is quite important for combining the advantages of vacuum tubes and solid-state devices but limited by the prevailing fabricating techniques which are expensive, time consuming and low-throughput. In this work, window-assisted nanosphere lithography (NSL) technique was proposed and enabled the low-cost and high-efficiency fabrication of nanostructures for vacuum micro-nano-electronic devices, thus allowing potential applications in many areas. As a demonstration, we fabricated high-density field emitter arrays which can be used as cold cathodes in vacuum micro-nano-electronic devices by using the window-assisted NSL technique. The details of the fabricating process have been investigated. This work provided a new and feasible idea for fabricating nanostructure arrays for vacuum micro-nano-electronic devices, which would spawn the development of vacuum micro-nano-electronics

THE EFFECT OF THE THICKNESS OF A PACKED BED ON THE DYNAMIC AND THERMAL BEHAVIOR OF A SOLAR DRYER

Directory of Open Access Journals (Sweden)

S KHALDI

2015-06-01

Full Text Available Drying food in the sun is a safe, easy and economical way to preserve food, especially fruits. Cabinet dryers are the most popular equipment for fruit drying. Because of intermittent nature of solar energy, storage is required for uninterrupted supply in order to match the needs. The main objective of this study is to assess effectiveness of continuous solar dryer integrated with packed bed as thermal storage with natural airflow for drying figs (Ficuscarica. The cabinet dryer were envisaged theoretically (computational fluid dynamics (CFD. The distribution of the velocity and temperature of air within the solar dryer were presented during one day of August and under the climate conditions of Tlemcen (Algeria.  The effects of presence of a packed bed on the distribution of velocity and temperature of airflow and on the temperature of figs were analyzed. The results show that the solar dryer design, incorporating a packed bed enhances the capabilities and performance of the solar dryer, through increasing time of drying.

Learning sustainability by developing a solar dryer for microalgae retrieval

Directory of Open Access Journals (Sweden)

Benedita Malheiro

2016-01-01

Full Text Available Excessive fossil fuel consumption is driving the search for alternative energy production solutions and, in particular, for sustainable sources of energy such as microalgae, from which biodiesel, among other useful compounds, can be obtained. After producing the microalgae, they must be harvested and dried. Existing drying solutions consume too much energy and are, therefore, expensive and unsustainable. The goal of this EPS@ISEP Spring 2013 project was to develop a solar microalgae dryer for the microalgae laboratory of ISEP. A multinational team of five students from distinct fields of study was responsible for designing and building the solar microalgae dryer prototype. The prototype includes a control system to ensure that the microalgae are not destroyed during the drying process. The solar microalgae dryer works as a distiller, extracting the excess water from the microalgae suspension. This paper details the design steps, the building technologies, the ethical and sustainable concerns and compares the prototype with existing solutions. The proposed sustainable microalgae drying process is competitive as far as energy usage is concerned. Finally, the project contributed to increase the team’s sustainable development awareness, active learning and motivation.

Weighing neutrinos in the scenario of vacuum energy interacting with cold dark matter: application of the parameterized post-Friedmann approach

Energy Technology Data Exchange (ETDEWEB)

Guo, Rui-Yun; Li, Yun-He; Zhang, Jing-Fei; Zhang, Xin, E-mail: guoruiyun110@163.com, E-mail: liyh19881206@126.com, E-mail: jfzhang@mail.neu.edu.cn, E-mail: zhangxin@mail.neu.edu.cn [Department of Physics, College of Sciences, Northeastern University, Shenyang 110004 (China)

2017-05-01

We constrain the neutrino mass in the scenario of vacuum energy interacting with cold dark matter by using current cosmological observations. To avoid the large-scale instability problem in interacting dark energy models, we employ the parameterized post-Friedmann (PPF) approach to do the calculation of perturbation evolution, for the Q = β H ρ{sub c} and Q = β H ρ{sub Λ} models. The current observational data sets used in this work include Planck (cosmic microwave background), BSH (baryon acoustic oscillations, type Ia supernovae, and Hubble constant), and LSS (redshift space distortions and weak lensing). According to the constraint results, we find that β > 0 at more than 1σ level for the Q = β H ρ{sub c} model, which indicates that cold dark matter decays into vacuum energy; while β = 0 is consistent with the current data at 1σ level for the Q = β H ρ{sub Λ} model. Taking the ΛCDM model as a baseline model, we find that a smaller upper limit, ∑ m {sub ν} < 0.11 eV (2σ), is induced by the latest BAO BOSS DR12 data and the Hubble constant measurement H {sub 0} = 73.00 ± 1.75 km s{sup −1} Mpc{sup −1}. For the Q = β H ρ{sub c} model, we obtain ∑ m {sub ν}<0.20 eV (2σ) from Planck+BSH. For the Q = β H ρ{sub Λ} model, ∑ m {sub ν}<0.10 eV (2σ) and ∑ m {sub ν}<0.14 eV (2σ) are derived from Planck+BSH and Planck+BSH+LSS, respectively. We show that these smaller upper limits on ∑ m {sub ν} are affected more or less by the tension between H {sub 0} and other observational data.

Method and apparatus for scientific analysis under low temperature vacuum conditions

Science.gov (United States)

Winefordner, James D.; Jones, Bradley T.

1990-01-01

A method and apparatus for scientific analysis of a sample under low temperature vacuum conditions uses a vacuum chamber with a conveyor belt disposed therein. One end of the conveyor belt is a cool end in thermal contact with the cold stage of a refrigerator, whereas the other end of the conveyor belt is a warm end spaced from the refrigerator. A septum allows injection of a sample into the vacuum chamber on top of the conveyor belt for spectroscopic or other analysis. The sample freezes on the conveyor belt at the cold end. One or more windows in the vacuum chamber housing allow spectroscopic analysis of the sample. Following the spectroscopic analysis, the conveyor belt may be moved such that the sample moves toward the warm end of the conveyor belt where upon it evaporates, thereby cleaning the conveyor belt. Instead of injecting the sample by way of a septum and use of a syringe and needle, the present device may be used in series with capillary-column gas chromatography or micro-bore high performance liquid chromatography.

Field measurements of temperature profile for floatovoltaic dryer in the tropics

Science.gov (United States)

Osman, F. A.; Ya'acob, M. E.; Iskandar, A. Noor

2017-09-01

Most of the equator region in a tropical climate zone experiences hot and humid weather but sometimes heavy rain and thunderstorms which occur stochastically in monsoon season. Sunlight which is the energy source can be harvested approximately 8 hours (on average basis) daily throughout the year which leads to the promotion of Solar PV technologies. This works projects the field performance for a new Floatovoltaic Dryer prototype with flexible PV roofing structures covering the top of the dryer system. The field measurements are collected on the lake of Engineering Faculty, UPM supported with 4-parameter weather station. Temperature profile with RH measurements inside the Floatovoltaic Dryer compartments as compared to direct-sun drying mechanism are the main contributions of this work and it projects more than 12 W of convection heat energy could be harvested by using the clean system. The field measurements imply various points of thermocouple and humidity sensor throughout the experiment. Temperature and humidity will be the main elements recorded to analyze the differences under monocrystalline PV panel as compared to natural drying.

Development and performance evaluation of a locally fabricated portable solar tunnel dryer for drying of fruits, vegetables and medicinal plants

International Nuclear Information System (INIS)

Munir, A.; Sultan, U.; Iqbal, M.

2013-01-01

The research was conducted to fabricate and develop a portable solar tunnel dryer (STD) for the drying of fruits, vegetables and medicinal plants. The system was designed as a portable system for decentralized applications at various sites to satisfy the drying requirements of small farmers and co-operatives. The cross sectional area of the solar tunnel dryer was trapezoidal in shape having 0.254 m/sup 2/ face area, with length and width of three meters and one meter respectively. It comprises a collector section (1.35 m) long and a drying section (1.65 m long) and two PV powered DC fans to provide the required air flow rate over the perishable agricultural products to be dried. Transparent polythene cover was used to close the dryer on top side to maintain the steady state air flow within the dryer. It has been observed that the drying air temperature was easily raised by some 8-14 degree C above the ambient temperature at air velocity ranges 0-1 m s/sup -1/. The efficiency of the solar tunnel dryer was found to be 40-45%. Psychrometric analysis was also carried out within the dryer and the process curves were drawn. The process curves were found similar to a conventional dryer showing that this dryer can be successfully utilized for the drying of agricultural products using solar energy. (author)

The effect of dryer load on freeze drying process design.

Science.gov (United States)

Patel, Sajal M; Jameel, Feroz; Pikal, Michael J

2010-10-01

Freeze-drying using a partial load is a common occurrence during the early manufacturing stages when insufficient amounts of active pharmaceutical ingredient (API) are available. In such cases, the immediate production needs are met by performing lyophilization with less than a full freeze dryer load. However, it is not obvious at what fractional load significant deviations from full load behavior begin. The objective of this research was to systematically study the effects of variation in product load on freeze drying behavior in laboratory, pilot and clinical scale freeze-dryers. Experiments were conducted with 5% mannitol (high heat and mass flux) and 5% sucrose (low heat and mass flux) at different product loads (100%, 50%, 10%, and 2%). Product temperature was measured in edge as well as center vials with thermocouples. Specific surface area (SSA) was measured by BET gas adsorption analysis and residual moisture was measured by Karl Fischer. In the lab scale freeze-dryer, the molar flux of inert gas was determined by direct flow measurement using a flowmeter and the molar flux of water vapor was determined by manometric temperature measurement (MTM) and tunable diode laser absorption spectroscopy (TDLAS) techniques. Comparative pressure measurement (capacitance manometer vs. Pirani) was used to determine primary drying time. For both 5% mannitol and 5% sucrose, primary drying time decreases and product temperature increases as the load on the shelves decreases. No systematic variation was observed in residual moisture and vapor composition as load decreased. Further, SSA data suggests that there are no significant freezing differences under different load conditions. Independent of dryer scale, among all the effects, variation in radiation heat transfer from the chamber walls to the product seems to be the dominant effect resulting in shorter primary drying time as the load on the shelf decreases (i.e., the fraction of edge vials increases).

Farm level evaluation of biomass energy operated seed dryer at selected sites of Bangladesh

International Nuclear Information System (INIS)

Rahman, S.M.M.; Bhuiyan, M.G.K.; Rahman, M.A.; Baqui, M.A.; Bala, B.K.

2006-01-01

Drying is one of the major problem in post harvest and processing of farm produce specially paddy seed in Bangladesh resulting tremendous shortage of quality seed. Evaluation through demonstrations was undertaken for the resource poor farmers at the selected sites to have practical experience of the IRRI-BRRI seed dryer. Viability of the dried paddy was more than 90% after six months of storage. The farmers were satisfied on the performance of the dryer. 68-100% farmers were motivated to hire the dyer during Boro and Aus seasons. Thus, the farm level evaluation and adoption of seed dryer will give a better alternative, aware and motivate the farmers on producing quality seed through proper drying and will contribute increased production

Feasibility analysis of heat pump dryer to dry hawthorn cake

International Nuclear Information System (INIS)

Wang, D.C.; Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L.

2011-01-01

Highlights: → A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. → Low drying temperature and high COP of heat pump are obtained in drying beginning. → HPD is more effective, economic than a traditional hot air dryer. → Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

Feasibility analysis of heat pump dryer to dry hawthorn cake

Energy Technology Data Exchange (ETDEWEB)

Wang, D.C., E-mail: wdechang@163.com [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China); Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L. [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China)

2011-08-15

Highlights: {yields} A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. {yields} Low drying temperature and high COP of heat pump are obtained in drying beginning. {yields} HPD is more effective, economic than a traditional hot air dryer. {yields} Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

R&D ERL: Vacuum

Energy Technology Data Exchange (ETDEWEB)

Mapes, M.; Smart, L.; Weiss, D.; Steszyn, A.; Todd, R.

2010-01-01

cryostat vacuum thermally insulating the SRF cavities need only reduce the convective heat load such that heat loss is primarily radiation through several layers of multi-layer insulation and conductive end-losses which are contained by 5{sup o}K thermal transitions. Prior to cool down rough vacuum {approx}10{sup -5} torr range is established and maintained by a dedicated turbomolecular pump station. Cryopumping by the cold mass and heat shields reduces the insulating vacuum to 10{sup -7} torr range after cool down.

Vacuum window glazings for energy-efficient buildings

Energy Technology Data Exchange (ETDEWEB)

Benson, D.K.; Smith, L.K.; Tracy, C.E.; Potter, T.; Christensen, C. (Solar Energy Research Inst., Golden, CO (USA)); Soule, D.E. (Western Illinois Univ., Macomb, IL (USA))

1990-05-01

The technical feasibility of a patented, laser-welded, evacuated insulating window was studied. The window has two edge-sealed sheets of glass separated by 0.5-mm glass spheres spaced 30 mm apart in a regular array. A highly insulating frame is required and several designs were analyzed. The vacuum window's combination of high solar transmittance and low thermal conductance makes it superior to many other windows in cold climates. In the US Pacific Northwest, the vacuum window could save about 6 MJ of heating energy annually per square meter of window in comparison to conventional, double-glazed windows. A large, vacuum laser-welding facility was designed and installed to conduct glass welding experiments and to fabricate full-sized vacuum windows. Experiments confirmed the feasibility of laser-sealing glass in vacuum but identified two difficulties. Under some circumstances, bubbles of dissolved gases form during welding and weaken the seal. Glass also vaporizes and contaminates the laser beam steering mirror. A novel moving metal foil mirror was developed to circumvent the contamination problem, but it has not yet been used to complete welding experiments and fabricate full-sized vacuum windows. 63 refs., 53 figs., 19 tabs.

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

Energy Technology Data Exchange (ETDEWEB)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi [Department of Mechanical Engineering, Shahid Bahonar University, Kerman (Iran, Islamic Republic of)

2006-01-15

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

International Nuclear Information System (INIS)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi

2006-01-01

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

A study of the drying effect on lemon slices using a closed-type solar dryer

Energy Technology Data Exchange (ETDEWEB)

Ho-Hsien Chen; Hernandez, C.E.; Tzou-Chi Huang [National Pingtung University of Science and Technology (China). Dept. of Food Science

2005-01-01

An experimental closed-type dryer associated with a photovoltaic system (PV) was developed. The transparent drying cabinet was designed with high transmittance glass to decrease the reflection of direct sunlight and to offer extra direct solar heating on the raw material during drying. Parallel wiring with a local electrical grid was necessary for switching purposes if there is insufficient battery backup during peak operation. Lemon slices were dried using the closed-type solar dryer and results were compared with hot air drying at 60{sup o}C. The results indicate that the dried lemon slices using a closed-type solar dryer has better general levels of quality in terms of sensory parameters. (author)

Performance Evaluation of a Pebble Bed Solar Crop Dryer ...

African Journals Online (AJOL)

Nigerian Journal of Technology ... The solar crop dryer consists of an imbedded pebble bed solar heat storage unit/solar collector ... The crop-drying chamber is made of drying trays of wire gauze while the roof is made of transparent glazing.

Design and Fabrication of a Direct Natural Convection Solar Dryer for Tapioca

Directory of Open Access Journals (Sweden)

Diemuodeke E. OGHENERUONA

2011-06-01

Full Text Available Based on preliminary investigations under controlled conditions of drying experiments, a direct natural convection solar dryer was designed and fabricated to dry tapioca in the rural area. This paper describes the design considerations followed and presents the results of MS excel computed results of the design parameters. A minimum of 7.56 m2 solar collector area is required to dry a batch of 100 kg tapioca in 20 hours (two days drying period. The initial and final moisture content considered were 79 % and 10 % wet basis, respectively. The average ambient conditions are 32ºC air temperatures and 74 % relative humidity with daily global solar radiation incident on horizontal surface of 13 MJ/m2/day. The weather conditions considered are of Warri (lat. 5°30’, long. 5°41’, Nigeria. A prototype of the dryer so designed was fabricated with minimum collector area of 1.08 m2. This prototype dryer will be used in experimental drying tests under various loading conditions.

Technical and environmental analysis of biofuel dryers; Teknisk och miljoemaessig analys av biobraensletorkar

Energy Technology Data Exchange (ETDEWEB)

Muenter, M; Hagman, U; Harnevie, H; Johansen, H; Kristensson, I; Westermark, M; Viberg, T [Vattenfall Energimarknad, Stockholm (Sweden)

1999-03-01

A study regarding technology and environmental impact of the drying process of biofuels has been conducted. In the study two different types of dryers are analyzed. The result from the study shows that emissions of primarily hydrocarbons is high from the direct technic. The emission can be decreased considerably by improving the burner of the dryer. For the indirect technic the evaporated water give rise to problems in the sewage treatment plant. Studies show that biological treatment will result in an acceptable condensate.

Commissioning of the Opal reactor cold neutron source

International Nuclear Information System (INIS)

Thiering, R.; Lu, W.; Ullah, R.

2006-01-01

Full text: At OPAL, Australia's first cold neutron facility will form an essential part of the reactor's research programs. Fast neutrons, born in the core of a reactor, interact with a cryogenic material, in this case liquid deuterium, to give them very low energies ( 1 0 m eV). A cold neutron flux of 1.4 1 0 E 1 4 n /cm 2/ s is expected, with a peak in the energy spectrum at 4.2m eV. The cold neutron source reached cryogenic conditions for the first time in late 2005. The cold neutron source operates with a sub-cooled liquid Deuterium moderator at 24 K. The moderator chamber, which contains the deuterium, has been constructed from AlMg 5. The thermosiphon and moderator chamber are cooled by helium gas, in a natural convection thermosiphon loop. The helium refrigeration system utilises the Brayton cycle, and is fully insulated within a high vacuum environment. Despite the proximity of the cold neutron source to the reactor core, it has been considered as effectively separate to the reactor system, due to the design of its special vacuum containment vessel. As OPAL is a multipurpose research reactor, used for beam research as well as radiopharmaceutical production and industrial irradiations, the cold neutron source has been designed with a stand-by mode, to maximise production. The stand-by mode is a warm operating mode using only gaseous deuterium at ambient temperatures (∼ 3 00 K ), allowing for continued reactor operations whilst parts of the cold source are unavailable or in maintenance. This is the first time such a stand-by feature has been incorporated into a cold source facility

Mushroom dehydration in a hybrid-solar dryer

International Nuclear Information System (INIS)

Reyes, Alejandro; Mahn, Andrea; Cubillos, Francisco; Huenulaf, Pedro

2013-01-01

Highlights: ► Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer. ► Effective diffusivity was estimated by the Constant Diffusivity Model. ► Drying kinetics were adjusted by a semi-theoretical and the empirical Page model. ► Temperature, thickness and air recycle significantly affected critical moisture. ► The input of solar energy resulted in 3.5–12.5% electrical energy saving. - Abstract: Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer (HSD) provided with a 3 m 2 solar panel and electric resistances. Mushrooms were cut in 8 mm or 4 mm thickness slices. At the outlet of the tray dryer 80–90% air was recycled and the air temperature was adjusted to the pre-defined levels (50 or 60 °C). At the outlet of the solar panel the air temperature raised between 2 and 20 °C above the ambient temperature, depending mainly of solar radiation level. Temperature, slices thickness and air recycle level had statistically significant effects on critical moisture content (X c ), as well as on the time necessary to reach a moisture content of 0.1 (wb). The color parameters of dehydrated mushroom indicate a notorious darkening, in all runs. Rehydration assays at 35 °C showed that in less than 30 min rehydrated mushrooms reached a moisture content of 0.8 (wb). Effective diffusivity (D eff ) was estimated by the Simplified Constant Diffusivity Model (SCDM), and it ranged between 6E−10 and 40E−10 m 2 /s, with R 2 higher than 0.98, agreeing with literature. The adjustment of experimental drying kinetics with the empirical Page’s model resulted in R 2 higher than 0.997. Finally, the input of solar energy resulted in 3.5–12.5% energy saving. These values could even be improved by increasing the agro-product load in the HSD

Improving Dryer and Press Efficiencies Through Combustion of Hydrocarbon Emissions

Energy Technology Data Exchange (ETDEWEB)

Sujit Banerjee

2005-10-31

Emission control devices on dryers and presses have been legislated into the industry, and are now an integral part of the drying system. These devices consume large quantities of natural gas and electricity and down-sizing or eliminating them will provide major energy savings. The principal strategy taken here focuses on developing process changes that should minimize (and in some cases eliminate) the need for controls. A second approach is to develop lower-cost control options. It has been shown in laboratory and full-scale work that Hazardous Air Pollutants (HAPs) emerge mainly at the end of the press cycle for particleboard, and, by extension, to other prod-ucts. Hence, only the air associated with this point of the cycle need be captured and treated. A model for estimating terpene emissions in the various zones of veneer dryers has been developed. This should allow the emissions to be concentrated in some zones and minimized in others, so that some of the air could be directly released without controls. Low-cost catalysts have been developed for controlling HAPs from dryers and presses. Catalysts conventionally used for regenerative catalytic oxidizers can be used at much lower temperatures for treating press emissions. Fluidized wood ash is an especially inexpensive mate-rial for efficiently reducing formaldehyde in dryer emissions. A heat transfer model for estimating pinene emissions from hot-pressing strand for the manufacture of flakeboard has been constructed from first principles and validated. The model shows that most of the emissions originate from the 1-mm layer of wood adjoining the platen surface. Hence, a simple control option is to surface a softwood mat with a layer of hardwood prior to pressing. Fines release a disproportionate large quantity of HAPs, and it has been shown both theo-retically and in full-scale work that particles smaller than 400 µm are principally responsible. Georgia-Pacific is considering green

Design, construction and test run of a two-tonne capacity solar rice dryer with rice-husk-fired auxiliary heater

International Nuclear Information System (INIS)

Iloeje, O.C.; Ekechukwu, O.V.; Ezeike, G.O.I.

1993-09-01

The design and construction details of a two-tonne per batch capacity natural-circulation solar rice dryer and the highlights of the design of its rice-husk-fired auxiliary heating system which is still under construction are presented. The dryer measures approximately 17.7m long by 9.8m wide by 6m high. Preliminary results of a test run on the solar dryer section only is reported. (author). 5 refs, 3 figs

Development of a multi-purpose dryer | Kadurumba | Nigeria ...

African Journals Online (AJOL)

The novel design uses heat sources from electric burners and it is located beneath the product spreading chamber. This prevented the problem of discoloration due to direct heat from the burners. A thermostat was used for its temperature control and light indicators were introduced to monitor the operation of the dryer with a ...

Recycle of valuable products from oily cold rolling mill sludge

Science.gov (United States)

Liu, Bo; Zhang, Shen-gen; Tian, Jian-jun; Pan, De-an; Liu, Yang; Volinsky, Alex A.

2013-10-01

Oily cold rolling mill (CRM) sludge contains lots of iron and alloying elements along with plenty of hazardous organic components, which makes it as an attractive secondary source and an environmental contaminant at the same time. The compound methods of "vacuum distillation + oxidizing roasting" and "vacuum distillation + hydrogen reduction" were employed for the recycle of oily cold rolling mill sludge. First, the sludge was dynamically vacuum distilled in a rotating furnace at 50 r/min and 600°C for 3 h, which removed almost hazardous organic components, obtaining 89.2wt% ferrous resultant. Then, high purity ferric oxide powders (99.2wt%) and reduced iron powders (98.9wt%) were obtained when the distillation residues were oxidized and reduced, respectively. The distillation oil can be used for fuel or chemical feedstock, and the distillation gases can be collected and reused as a fuel.

Sodium removal and requalification of secondary loop cold trap

International Nuclear Information System (INIS)

Rajan, M.; Veerasamy, R.; Gurumoorthy, K.; Rajan, K.K.; Kale, R.D.

1997-01-01

The secondary loop cold trap of the Fast Breeder Test Reactor got plugged prematurely and was not removing impurities from the sodium. This cold trap was taken up for cleaning and modification of the internals. The cleaning operation was carried out successfully by hydride decomposition and vacuum distillation followed by steam cleaning method. Without dismantling, the cold trap internals were washed by circulating water. Subsequently the wire mesh was removed, examined and replaced, the internal modifications were carried (nit and the cold trap way qualified for reuse. The procedures followed and the experience gained are discussed. (author)

R and D ERL: Vacuum

International Nuclear Information System (INIS)

Mapes, M.; Smart, L.; Weiss, D.; Steszyn, A.; Todd, R.

2010-01-01

insulating the SRF cavities need only reduce the convective heat load such that heat loss is primarily radiation through several layers of multi-layer insulation and conductive end-losses which are contained by 5 o K thermal transitions. Prior to cool down rough vacuum ∼10 -5 torr range is established and maintained by a dedicated turbomolecular pump station. Cryopumping by the cold mass and heat shields reduces the insulating vacuum to 10 -7 torr range after cool down.

Corn Drying with Zeolite in The Fluidized Bed Dryer under Medium Temperature

Directory of Open Access Journals (Sweden)

Mohamad Djaeni

2013-08-01

Full Text Available Drying is an important step to find high quality of corn. Based on Standard of National Industry, populer as SNI, number 01-3920-1995, the corn was well stored at moisture content 14% or below (wet basis. However, conventional corn drying dealed with in-efficient energy process and corn quality degradation. This research evaluated the performance of corn drying assisted by zeolite as moisture adsorbent. In this process, the zeolite and corn were placed in the dryer fluidized by warm air as drying medium under 40 - 50oC. The air evaporated water product from corn, and at same time the zeolite adsorbed moisture in air. So, the relative humidity of air in dryer can be kept low in which enhanced the driving force for drying. Beside that, the moisture adsoprtion by zeolite was exothermic process that can supply the energy for drying or keep the dryer temperature. Thus, the drying rate can be faster. This work foccussed to observe the effect of drying temperature, air velocity, and corn to zeolite ratio on drying time as well as corn quality. As indicators, the drying rate was estimated and the proxymates content such as protein, fat, and carbohydrate content were analyzed. The results showed that compared with conventional fluidised bed dryer, corn drying with zeolite, can speed up drying time as well as improving the constant of drying rate. In addition, the corn proximate nutrition content can be well retained. At operating temperature 40oC, air velocity 9 m.s-1, and zeolite to corn ratio 1:2, the drying time can be 60 minutes shorter compared to that without zeolite.

A large-scale solar greenhouse dryer using polycarbonate cover: Modeling and testing in a tropical environment of Lao People's Democratic Republic

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm; Intawee, Poolsak; Kaewkiew, Jinda; Sritus, Chanoke [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand); Khamvongsa, Vathsana [Department of Physics, Faculty of Natural Science, National University of Laos, P O Box 7322, Vientiane (Lao People' s Democratic Republic)

2011-03-15

A large-scale solar greenhouse dryer with a loading capacity of 1000 kg of fruits or vegetables has been developed and tested at field levels. The dryer has a parabolic shape and the dryer is covered with polycarbonate sheets. The base of the dryer is a black concrete floor with an area of 7.5 x 20.0 m{sup 2}. Nine DC fans powered by three 50-W solar cell modules are used to ventilate the dryer. The dryer was installed at Champasak (15.13 N, 105.79 E) in Lao People's Democratic Republic (Lao PDR). It is routinely used to dry chilli, banana and coffee. To assess the experimental performances of the dryer, air temperature, air relative humidity and product moisture contents were measured. One thousand kilograms of banana with the initial moisture content of 68% (wb) was dried within 5 days, compared to 7 days required for natural sun drying with the same weather conditions. Also three hundred kilograms of chilli with the initial moisture content of 75% (wb) was dried within 3 days while the natural sun drying needed 5 days. Two hundred kilograms of coffee with the initial moisture content of 52% (wb) was dried within 2 days as compared to 4 days required for natural sun drying. The chilli, coffee and banana dried in this dryer were completely protected from insects, animals and rain. Furthermore, good quality of dried products was obtained. The payback period of the dryer is estimated to be 2.5 years. A system of partial differential equations describing heat and moisture transfer during drying of chilli, coffee and banana in the greenhouse dryer was developed. These equations were solved by using the finite different method. The simulated results agree well with the experimental data. This model can be used to provide the design data for this type of dryer in other locations. (author)

Thermal decomposition study of uranyl nitrate and cerium hydroxide in a spray dryer

International Nuclear Information System (INIS)

Silva Wildhagen, G.R. da.

1993-05-01

A study, in a spray dryer system based on drying and thermal decomposition of uranyl nitrate solutions aiming the production of uranium trioxide adequate for the use in posterior steps of reduction and hydro fluorination in nuclear fuel cycle; and cerium hydroxide suspensions for the production of cerium oxide with high surface area is presented. Thus, the project and construction of a countercurrent spray dryer was elaborated for capacity of 10 Kg U O 3 /h and 3,5 k Ce O 2 /h. The methodology used in these experiments consisted in the analysis of several parameters (concentration and flow rate of the feed, atomization pressure and inlet temperature of the dryer) over the physical and chemical properties of the products. Using the obtained results, with the help of a mathematical model, it was developed the project of a continuous pilot unity for the production of uranium trioxide or cerium oxide, with capacity of 20 Kg U O 3 /h or 10 Kg Ce O 2 /h, respectively. (author)

A solar assisted heat-pump dryer and water heater

International Nuclear Information System (INIS)

Hawlader, M.N.A.; Chou, S.K.; Jahangeer, K.A.; Rahman, S.M.A.

2006-01-01

Growing concern about the depletion of conventional energy resources has provided impetus for considerable research and development in the area of alternative energy sources. A solar assisted heat pump dryer and water heater found to be one of the solutions while exploring for alternative energy sources. The heat pump system is used for drying and water heating applications with the major share of the energy derived from the sun and the ambient. The solar assisted heat pump dryer and water heater has been designed, fabricated and tested. The performance of the system has been investigated under the meteorological conditions of Singapore. The system consists of a variable speed reciprocating compressor, evaporator-collector, storage tank, air cooled condenser, auxiliary heater, blower, dryer, dehumidifier, and air collector. The drying medium used is air and the drying chamber is configured to carry out batch drying of good grains. A water tank connected in series with the air cooled condenser delivers hot water for domestic applications. The water tank also ensures complete condensation of the refrigerant vapour. A simulation program is developed using Fortran language to evaluate the performance of the system and the influence of different variables. The performance indices considered to evaluate the performance of the system are: Solar Fraction (SF), Coefficient of Performance (COP) and Specific Moisture Extraction Rate (SMER). A COP value of 7.5 for a compressor speed of 1800 rpm was observed. Maximum collector efficiencies of 0.86 and 0.81 have been found for evaporator-collector and air collector, respectively. A value of the SMER of 0.79 has been obtained for a load of 20 kg and a compressor speed of 1200 rpm

Interaction of cold radiofrequency plasma with seeds of beans (Phaseolus vulgaris)

Science.gov (United States)

Bormashenko, Edward; Shapira, Yekaterina; Grynyov, Roman; Whyman, Gene; Bormashenko, Yelena; Drori, Elyashiv

2015-01-01

The impact of cold radiofrequency air plasma on the wetting properties and water imbibition of beans (Phaseolus vulgaris) was studied. The influence of plasma on wetting of a cotyledon and seed coat (testa) was elucidated. It was established that cold plasma treatment leads to hydrophilization of the cotyledon and tissues constituting the testa when they are separately exposed to plasma. By contrast, when the entire bean is exposed to plasma treatment, only the external surface of the bean is hydrophilized by the cold plasma. Water imbibition by plasma-treated beans was studied. Plasma treatment markedly accelerates the water absorption. The crucial role of a micropyle in the process of water imbibition was established. It was established that the final percentage of germination was almost the same in the cases of plasma-treated, untreated, and vacuum-pumped samples. However, the speed of germination was markedly higher for the plasma-treated samples. The influence of the vacuum pumping involved in the cold plasma treatment on the germination was also clarified. PMID:25948708

Development of Simple Drying Model for Performance Prediction of Solar Dryer: Theoretical Analysis

DEFF Research Database (Denmark)

Singh, Shobhana; Kumar, Subodh

2012-01-01

An analytical moisture diffusion model which considers the influence of external resistance to mass transfer is developed to predict thermal performance of dryer system. The moisture diffusion coefficient, Deff that is necessary to evaluate the prediction model has been determined in terms...... of experimental drying parameters. A laboratory model of mixed-mode solar dryer system is tested with cylindrical potato samples of thickness 5 and 18 mm under simulated indoor conditions. The potato samples were dried at a constant absorbed thermal energy of 750 W/m2 and air mass flow rate of 0.011 kg...

LHC vacuum system

CERN Document Server

Gröbner, Oswald

1999-01-01

The Large Hadron Collider (LHC) project, now in the advanced construction phase at CERN, comprises two proton storage rings with colliding beams of 7-TeV energy. The machine is housed in the existing LEP tunnel with a circumference of 26.7 km and requires a bending magnetic field of 8.4 T with 14-m long superconducting magnets. The beam vacuum chambers comprise the inner 'cold bore' walls of the magnets. These magnets operate at 1.9 K, and thus serve as very good cryo-pumps. In order to reduce the cryogenic power consumption, both the heat load from synchrotron radiation emitted by the proton beams and the resistive power dissipation by the beam image currents have to be absorbed on a 'beam screen', which operates between 5 and 20 K and is inserted inside the vacuum chamber. The design of this beam screen represents a technological challenge in view of the numerous and often conflicting requirements and the very tight mechanical tolerances imposed. The synchrotron radiation produces strong outgassing from the...

Performance analysis of greenhouse dryer by using insulated north-wall under natural convection mode

Directory of Open Access Journals (Sweden)

Prashant Singh Chauhan

2016-11-01

Full Text Available A prototype north wall insulated greenhouse dryer has been fabricated and tested in no-load conditions under natural convection mode. Experimentation has been conducted in two different cases. Case-I is when solar collector placed inside the dryer and Case-II is North wall insulated greenhouse dryer without solar collector. Coefficient of performance, heat utilisation factor, convective heat transfer coefficient and coefficient of diffusivity have been evaluated in thermal performance analysis. The difference of the highest convective heat transfer coefficient of both cases is 29.094W/m2°C which is showing the effectiveness of insulated north wall and solar collector. The maximum coefficient of diffusivity (0.0827 was achieved during the third day of experiment in Case-II. The inside room temperature of wall insulated greenhouse dryer for Case-I is 4.11%, 5.08 % and 11.61 % higher than the Case-II during the day 1, day 2 and day 3 respectively. This result is also showing the effectiveness of solar collector and insulated north wall. The highest heat utilisation factor (0.616 is obtained during the second day for Case-I while for Case-II it is 0.769 during the third day of experimentation. Maximum coefficient of performance achieved is 0.892 during the third day of the experiment for Case-I whereas 0.953 is obtained on the first day of experimentation for Case-II.

Interacting vacuum energy in the dark sector

Energy Technology Data Exchange (ETDEWEB)

Chimento, L. P. [Departamento de Física, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires and IFIBA, CONICET, Cuidad Universitaria, Buenos Aires 1428 (Argentina); Carneiro, S. [Instituto de Física, Uníversídade Federal da Bahia, 40210-340, Salvador, BA (Brazil)

2015-03-26

We analyse three cosmological scenarios with interaction in the dark sector, which are particular cases of a general expression for the energy flux from vacuum to matter. In the first case the interaction leads to a transition from an unstable de Sitter phase to a radiation dominated universe, avoiding in this way the initial singularity. In the second case the interaction gives rise to a slow-roll power-law inflation. Finally, the third scenario is a concordance model for the late-time universe, with the vacuum term decaying into cold dark matter. We identify the physics behind these forms of interaction and show that they can be described as particular types of the modified Chaplygin gas.

Drying of Rosella (Hibiscus sabdariffa) Flower Petals using Solar Dryer with Double Glass Cover Collector

OpenAIRE

Tjukup Marnoto

2014-01-01

Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture conten...

Changing MFTF vacuum environment

International Nuclear Information System (INIS)

Margolies, D.; Valby, L.

1982-12-01

The Mirror Fusion Test Facility (MFTF) vacuum vessel will be about 60m long and 10m in diameter at the widest point. The allowable operating densities range from 2 x 10 9 to 5 x 10 10 particles per cc. The maximum leak rate of 10 - 6 tl/sec is dominated during operation by the deliberately injected cold gas of 250 tl/sec. This gas is pumped by over 1000 square meters of cryopanels, external sorption pumps and getters. The design and requirements have changed radically over the past several years, and they are still not in final form. The vacuum system design has also changed, but more slowly and less radically. This paper discusses the engineering effort necessary to meet these stringent and changing requirements. Much of the analysis of the internal systems has been carried out using a 3-D Monte Carlo computer code, which can estimate time dependent operational pressures. This code and its use will also be described

Steam generator with integral downdraft dryer. Final project report

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

Atom Interferometry for Dark Contents of the Vacuum Searches

Energy Technology Data Exchange (ETDEWEB)

Burrow, O. [Liverpool U.; Carroll, A. [Liverpool U.; Chattopadhyay, S. [Northern Illinois U.; Coleman, J. [Liverpool U.; Elertas, G. [Teddington, Natl. Phys. Lab; Heffer, J. [Liverpool U.; Metelko, C. [Liverpool U.; Moore, R. [Teddington, Natl. Phys. Lab; Morris, D. [Liverpool U.; Perl, M. [SLAC; Ralph, J. [Liverpool U.; Tinsley, J. [Teddington, Natl. Phys. Lab

2017-05-25

A cold atom interferometer is being developed using 85Rb atoms towards a search for the dark contents of the vacuum, and as a test stand for inertial sensing applications. Here we outline the current status of the experiment and report the observation of Ramsey interference fringes in the apparatus.

A model for the thermodynamic analysis in a batch type fluidized bed dryer

International Nuclear Information System (INIS)

Özahi, Emrah; Demir, Hacımurat

2013-01-01

An original model for thermodynamic analysis of a batch type fluidized bed dryer is proposed herein considering two separate systems comprised of drying air medium as a control volume and particles to be dried as a control mass. By means of the proposed model, energetic and exergetic analyses of a drying column of a batch type fluidized bed dryer are carried out as an original contribution to literature since there is no such like model in which the analyses are performed considering two separate systems. The energetic efficiencies evaluated by means of the proposed model using the data in literature are compared with those in literature and a good conformity is satisfied with an acceptable error margin of ±9%. A new correlation is also developed with a mean deviation of ±10% in order to evaluate the energetic efficiency for not only corn drying process but also drying processes of other particles at inlet air temperature of 50 °C. Effects of air mass flow rate, mass of particle and ambient temperature on energetic and exergetic efficiencies are analyzed and some concluding remarks are highlighted for further studies. - Highlights: • Energetic and exergetic analyses of a batch type fluidized bed dryer are developed. • An original model is proposed for thermodynamic analyses in a fluidized bed dryer. • The proposed model is compared with the data in literature with an accuracy of ±9%. • Effect of air mass flow rate is more significant than that of ambient temperature. • Effect of mass of particle is more significant than that of ambient temperature

Development of a compact freeze vacuum drying for jelly fish (Schypomedusae)

Science.gov (United States)

Alhamid, M. Idrus; Yulianto, M.; Nasruddin

2012-06-01

A new design of a freeze vacuum drying with internal cooling and heater from condenser's heat loss was built and tested. The dryer was used to dry jelly fish (schypomedusae), to study the effect of drying parameters such as the temperature within the drying chamber on mass losses (evaporation) during the freezing stage and the moisture ratio at the end of the drying process. The midili thin layer mathematical drying model was used to estimate and predict the moisture ratio curve based on different drying chamber temperatures. This experiment shows that decreasing the drying chamber temperature with constant pressure results in less mass loss during the freezing stage Drying time was reduced with an increase in drying temperature. Decreasing the drying chamber temperature results in lower pressure saturation of the material has no effect of drying chamber pressure on mass transfer.

Comparison of three control strategies for optimization of spray dryer operation

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2017-01-01

controllers for operation of a four-stage spray dryer. The three controllers are a proportional-integral (PI) controller that is used in industrial practice for spray dryer operation, a linear model predictive controller with real-time optimization (MPC with RTO, MPC-RTO), and an economically optimizing...... nonlinear model predictive controller (E-NMPC). The MPC with RTO is based on the same linear state space model in the MPC and the RTO layer. The E-NMPC consists of a single optimization layer that uses a nonlinear system of ordinary differential equations for its predictions. The PI control strategy has...... the production rate, while minimizing the energy consumption, keeping the residual moisture content of the powder below a maximum limit, and avoiding that the powder sticks to the chamber walls. We use an industrially recorded disturbance scenario in order to produce realistic simulations and conclusions...

Laboratory Development of A High Capacity Gas-Fired paper Dryer

Energy Technology Data Exchange (ETDEWEB)

Chudnovsky, Yaroslav [Gas Technology Institute, Des Plaines, IL (United States); Kozlov, Aleksandr [Gas Technology Institute, Des Plaines, IL (United States); Sherrow, Lester [Gas Technology Institute, Des Plaines, IL (United States)

2005-09-30

Paper drying is the most energy-intensive and temperature-critical aspect of papermaking. It is estimated that about 67% of the total energy required in papermaking is used to dry paper. The conventional drying method uses a series of steam-heated metal cylinders that are required to meet ASME codes for pressure vessels, which limits the steam pressure to about 160 psig. Consequently, the shell temperature and the drying capacity are also limited. Gas Technology Institute together with Boise Paper Solutions, Groupe Laparrier and Verreault (GL&V) USA Inc., Flynn Burner Corporation and with funding support from the U.S. Department of Energy, U.S. natural gas industry, and Gas Research Institute is developing a high efficiency gas-fired paper dryer based on a combination of a ribbon burner and advanced heat transfer enhancement technique. The Gas-Fired Paper Dryer (GFPD) is a high-efficiency alternative to conventional steam-heated drying drums that typically operate at surface temperatures in the 300ºF range. The new approach was evaluated in laboratory and pilot-scale testing at the Western Michigan University Paper Pilot Plant. Drum surface temperatures of more than 400ºF were reached with linerboard (basis weight 126 lb/3000 ft2) production and resulted in a 4-5 times increase in drying rate over a conventional steam-heated drying drum. Successful GFPD development and commercialization will provide large energy savings to the paper industry and increase paper production rates from dryer-limited (space- or steam-limited) paper machines by an estimated 10 to 20%, resulting in significant capital costs savings for both retrofits and new capacity.

Drying of Ceramic Hollow Bricks in an Industrial Tunnel Dryer: A Finite Volume Analysis

Directory of Open Access Journals (Sweden)

F Tavares

2016-10-01

Full Text Available This paper aims to study the drying of industrial hollow bricks in a tunnel dryer cross flow type. The theoretical model is based on mass and energy conservation equations applied to air and product. To validate the methodology, numerical and experimental results for the moisture content and the temperature of brick during the drying in an industrial scale are compared and a good correlation was obtained. Results of moisture content and temperature of the product, and temperature, relative humidity and absolute humidity of drying air as a function of drying time and position in the dryer are presented and analyzed.

Improving adsorption dryer energy efficiency by simultaneous optimization and heat integration

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Conventionally, energy-saving techniques in drying technology are sequential in nature. First, the dryer is optimized without heat recovery and then, based on the obtained process conditions, heat recovery possibilities are explored. This work presents a methodology for energy-efficient adsorption

Design and Testing of a Natural Convection Solar Tunnel Dryer for Mango

Directory of Open Access Journals (Sweden)

Isaac Nyambe Simate

2017-01-01

Full Text Available A natural convection solar tunnel dryer comprising three major units, a solar collector unit, a drying unit, and a vertical bare flat-plate chimney, was constructed. No-load tests with a horizontal configuration of air entry into the collector resulted in a bidirectional air flow in the dryer. To correct this undesirable situation, an air guide at the collector was incorporated to ensure that air entered in a vertical direction. To investigate its performance, drying experiments with mango were carried out at the University of Zambia, Department of Agricultural Engineering. Uncertainties in the parameters measured in the experiment were analysed and quantified. The results showed that, under solar radiation between 568.4 and 999.5 W/m2, air temperature of up to 65.8°C was attained at the collector unit. The average relative humidity values were 30.8%, 6.4%, and 8.4% for the ambient, collector, and drying unit, respectively. Under these conditions, mango with an initial moisture content of 85.5% (wet basis was dried to 13.0% (wet basis in 9.5 hours. The collector, drying, and pick-up efficiencies were found to be 24.7%, 12.8%, and 35.0%, respectively. The average temperature difference between the chimney air and ambient air was 12.1°C, and this was sufficient in driving the flow of air through the dryer.

Sympathetic cooling of nanospheres with cold atoms

Science.gov (United States)

Montoya, Cris; Witherspoon, Apryl; Ranjit, Gambhir; Casey, Kirsten; Kitching, John; Geraci, Andrew

2016-05-01

Ground state cooling of mesoscopic mechanical structures could enable new hybrid quantum systems where mechanical oscillators act as transducers. Such systems could provide coupling between photons, spins and charges via phonons. It has recently been shown theoretically that optically trapped dielectric nanospheres could reach the ground state via sympathetic cooling with trapped cold atoms. This technique can be beneficial in cases where cryogenic operation of the oscillator is not practical. We describe experimental advances towards coupling an optically levitated dielectric nanosphere to a gas of cold Rubidium atoms. The sphere and the cold atoms are in separate vacuum chambers and are coupled using a one-dimensional optical lattice. This work is partially supported by NSF, Grant Nos. PHY-1205994,PHY-1506431.

Thermal decomposition of uranylnitrate by the Spray-Dryer process

International Nuclear Information System (INIS)

Wildhagen, G.R.S.; Silva, G.C. da

1988-01-01

The proposal of this work consist in the thermal decomposition of uranyl nitrate solutions by the Spray-Dryer process aiming the production of highly reactive fluidized UO 3 , adequate for the use in posterior of reduction to UO 2 and hydrofluorination to UF 4 , in a fluidized bed for the obtention of UF 6 in the cicle of nuclear fuels. (author) [pt

Novel temperature control technique for a medicinal herb dryer system powered by a photovoltaic array

International Nuclear Information System (INIS)

Abd El-Shafy A Nafeh; Hanaa M Fargali; Faten H Fahmy; Mohamed A Hassan

2006-01-01

Each plant has its own optimal drying temperature, especially for the medicinal herbs, because they are sensitive to heat. If the drying temperature becomes more than the optimal value, some chemical reactions will occur and influence the quality of the dried herb, such as color, taste, and aroma. While if the drying temperature becomes lower than the optimal value, the drying process will slow down; and consequently an expected degradation in the quality of the herb may occur, due to insects and fungi infestation which increase in moist conditions. This paper presents a new temperature control technique for a medicinal herb dryer system. The technique fixes the drying temperature of the medicinal herbs at 40 degree C, even in cases of rapidly changing atmospheric conditions. The control of the dryer temperature is achieved through using the proportional integral (PI) controller. The designed dryer contains two systems, which are the thermal and the electrical systems. The thermal system is designed to heat the drying air by using the solar energy and bio-gas fuel. Whereas, the electrical system, which contains a photovoltaic (PV) modules and a battery, is designed to supply the different electrical loads of the dryer system. The control technique is investigated through simulation work by using MATLAB-SIMULINK. The simulation results indicate the high capability of the proposed technique in controlling the drying temperature, even in cases of rapidly changing atmospheric conditions

Fluid bed dryer and Aeropep solidification system. Amendment 1 to topical report

International Nuclear Information System (INIS)

1975-01-01

Information is presented on interfaces between the aerojet fluid bed dryer and the liquid radwaste system, plant ventilation system, and radioactive solid waste handling system for BWR and PWR type reactors. (U.S.)

Determination of stresses caused by fluctuation of acoustic load in the steam dryers of a BWR

International Nuclear Information System (INIS)

Centeno P, J.; Quezada G, S.; Prieto G, A.; Vazquez R, A.; Espinosa P, G.; Nunez C, A.

2014-10-01

The extended power up-rate (EPU) in a nuclear power plant cause various problems in BWR components also in the steam system. This due to increased steam flow generated in the reactor and is conveyed to the turbine by the four main steam lines (MSL). One of the most serious problems is the generation of acoustic pressure loads in the metal structure of the steam dryer which eventually leads to fatigue failure and even the appearance of cracks, and in turn it causes loose parts that are entrained by the steam and transported in the MSL. This problem is due to the fluctuation of load acoustics caused by the union of the safety or relief valves (SRV) with the MSL, spreading through these to reach the reactor pressure vessel (RPV) where the effect of resonance of the acoustic wave is amplified and impacts directly in the supporting structure of the steam dryer, skirt and the panels where the mixture liquid-steam is dried, by centrifugation effect and runoff of liquid water. Efforts in the steam dryer operating conditions of EPU for two cases will be analyzed in this work, the first is before the installation of Acoustic Side Branch (ASB), and in the second case we consider the installation of said ASB in the standpipes of SRV. The analysis was performed with numerical experiments on a platform for computational fluid dynamics with virtual geometries previously designed based on the actual components of the reactor and steam system. The model to study is delimited by the top of the RPV, the steam dryer and a section of each of the four MSL with ten standpipes of SRV. With the obtained data and considering the mechanical-structural properties of the steam dryer material, we can evaluate the mechanical resistance to impacts by acoustic pressure load and its possible deformation or cracking. (Author)

Modeling of thermal mode of drying special purposes ceramic products in batch action chamber dryers

Science.gov (United States)

Lukianov, E. S.; Lozovaya, S. Yu; Lozovoy, N. M.

2018-03-01

The article is devoted to the modeling of batch action chamber dryers in the processing line for producing shaped ceramic products. At the drying stage, for various reasons, most of these products are warped and cracked due to the occurrence of irregular shrinkage deformations due to the action of capillary forces. The primary cause is an untruly organized drying mode due to imperfection of chamber dryers design specifically because of the heat-transfer agent supply method and the possibility of creating a uniform temperature field in the whole volume of the chamber.

Evaluation of energy consumption in different drying methods

Energy Technology Data Exchange (ETDEWEB)

Motevali, Ali; Minaei, Saeid; Khoshtagaza, Mohammad Hadi [Department of Agricultural Machinery Engineering, Agricultural Faculty, Tarbiat Modares University, Tehran 14115-111 (Iran, Islamic Republic of)

2011-02-15

This study was conducted to evaluate energy consumption in various drying systems including hot-air convection, use of microwave pretreatment with convection dryer, microwave drying, vacuum drying and infrared drying. Tests were conducted using pomegranate arils under various experimental conditions as follows. In convection dryer at six temperature levels (45, 50, 55, 60, 65 and 70 C) and three air velocity levels (0.5, 1 and 1.5 m/s) at three pretreatments of control, 100 W microwave pretreatment for 20 min and 200 W microwave pretreatment for 10 min. Experiments in the microwave dryer were done at three power levels of 100, 200 and 300 W and in vacuum dryer at five temperature levels (50, 60, 70, 80, and 90 C) under 250 kPa pressure. For infrared drying, there were four air velocity levels (0.3, 0.5, 0.7 and 1 m/s) and three illumination levels (0.22, 0.31 and 0.49 W/cm{sup 2}). Experimental results showed that minimum and maximum energy consumption in pomegranate drying were associated with microwave and vacuum dryers, respectively. The use of microwave pretreatment in drying pomegranate arils in hot air dryer decreased drying time and energy consumption in comparison with pure convection drying. In infrared drying, it was found that drying time increased with air velocity which resulted in increased energy consumption. (author)

Evaluation of energy consumption in different drying methods

International Nuclear Information System (INIS)

Motevali, Ali; Minaei, Saeid; Khoshtagaza, Mohammad Hadi

2011-01-01

This study was conducted to evaluate energy consumption in various drying systems including hot-air convection, use of microwave pretreatment with convection dryer, microwave drying, vacuum drying and infrared drying. Tests were conducted using pomegranate arils under various experimental conditions as follows. In convection dryer at six temperature levels (45, 50, 55, 60, 65 and 70 o C) and three air velocity levels (0.5, 1 and 1.5 m/s) at three pretreatments of control, 100 W microwave pretreatment for 20 min and 200 W microwave pretreatment for 10 min. Experiments in the microwave dryer were done at three power levels of 100, 200 and 300 W and in vacuum dryer at five temperature levels (50, 60, 70, 80, and 90 o C) under 250 kPa pressure. For infrared drying, there were four air velocity levels (0.3, 0.5, 0.7 and 1 m/s) and three illumination levels (0.22, 0.31 and 0.49 W/cm 2 ). Experimental results showed that minimum and maximum energy consumption in pomegranate drying were associated with microwave and vacuum dryers, respectively. The use of microwave pretreatment in drying pomegranate arils in hot air dryer decreased drying time and energy consumption in comparison with pure convection drying. In infrared drying, it was found that drying time increased with air velocity which resulted in increased energy consumption.

Economic Optimization of Spray Dryer Operation using Nonlinear Model Predictive Control

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we investigate an economically optimizing Nonlinear Model Predictive Control (E-NMPC) for a spray drying process. By simulation we evaluate the economic potential of this E-NMPC compared to a conventional PID based control strategy. Spray drying is the preferred process to reduce...... the water content for many liquid foodstuffs and produces a free flowing powder. The main challenge in controlling the spray drying process is to meet the residual moisture specifications and avoid that the powder sticks to the chamber walls of the spray dryer. We present a model for a spray dryer that has...... been validated on experimental data from a pilot plant. We use this model for simulation as well as for prediction in the E-NMPC. The E-NMPC is designed with hard input constraints and soft output constraints. The open-loop optimal control problem in the E-NMPC is solved using the single...

performance evaluation of a pebble bed solar crop dryer abstract

African Journals Online (AJOL)

Dr Obe

The open-air sun drying is prevalent and very common in the rural areas. Farmers spread their agricultural produce such as maize, cassava, pepper, tomatoes etc. ... drying system. The abundance of solar radiation in. Nigeria could make crop drying with solar dryers very easy and simple. Economic appraisal of solar drying ...

Performance Evaluation of an Active Solar Dryer Equipped with an Auxilliary Electrical Heater and Heat Recovery System

International Nuclear Information System (INIS)

Pourghasemi Ranjbar, M.; Alavi Naeini, N.; Mortezapour, H.

2016-01-01

Drying is a very sophisticated process which consumes a large amount of energy. Solar energy can be used as an alternative or supplementary energy source to fossil fuels. Solar dryers are common ways for saving fossil fuel consumption during agricultural products drying. In this study, the performance of an active solar dryer equipped with an energy recovery system was investigated at three levels of drying air temperature. The results showed that the energy recovery system was able to increase inlet air temperature by 16.8, 18.5 and 18.9 ° C at drying temperatures of 55, 65 and 75 ℃, respectively. Meanwhile 47.8, 42.9 and 40.9 percents of the dryer exhaust air energy were recovered respectively at these conditions which subsequently led to a reduction of 30.7, 19.2 and 14.7 percents in electrical heater energy consumption.

Direct growth of Ge1-xSnx films on Si using a cold-wall ultra-high-vacuum chemical-vapor-deposition system

Directory of Open Access Journals (Sweden)

Aboozar eMosleh

2015-04-01

Full Text Available Germanium tin alloys were grown directly on Si substrate at low temperatures using a cold-wall ultra-high vacuum chemical vapor deposition system. Epitaxial growth was achieved by adopting commercial gas precursors of germane and stannic chloride without any carrier gases. The X-ray diffraction analysis showed the incorporation of Sn and that the Ge1-xSnx films are fully epitaxial and strain relaxed. Tin incorporation in the Ge matrix was found to vary from 1% to 7%. The scanning electron microscopy images and energy dispersive X-ray spectra maps show uniform Sn incorporation and continuous film growth. Investigation of deposition parameters shows that at high flow rates of stannic chloride the films were etched due to the production of HCl. The photoluminescence study shows the reduction of bandgap from 0.8 eV to 0.55 eV as a result of Sn incorporation.

Development of an active solar crop dryer: design analysis and ...

African Journals Online (AJOL)

The design analysis and performance evaluation of an active solar crop dryer was undertaken by drying marched cassava. The drying rate, system drying, collector and pick-up efficiencies were 1.6kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9kg/day. The collector ...

Fermion number non-conservation and cold neutral fermionic matter in (V-A) gauge theories

International Nuclear Information System (INIS)

Matveev, V.A.; Rubakov, V.A.; Tavkhelidze, A.N.; Tokarev, V.F.

1987-01-01

It is shown that in four-dimensional abelian (V-A) theories, the ground state of cold neutral fermionic matter is an anomalous state containing domains of abnormal phase surrounded by the normal vacuum. Inside these domains, there exists a gauge field condensate which makes real fermions disappear both inside and outside the domains. In non-abelian theories, the abnormal matter is unstable in its turn, and the system rolls back down into the normal state with a small number of fermions above the topologically non-trivial vacuum. Thus, in several non-abelian gauge theories, the fermion number density of cold neutral matter cannot exceed some critical value. (orig.)

Vibration Analysis for Steam Dryer of APR1400 Steam Generator

Energy Technology Data Exchange (ETDEWEB)

Han, Sung-heum; Ko, Doyoung [KHNP CRI, Daejeon (Korea, Republic of); Cho, Minki [Doosan Heavy Industry, Changwon (Korea, Republic of)

2016-10-15

This paper is related to comprehensive vibration assessment program for APR1400 steam generator internals. According to U.S. Nuclear Regulatory Commission, Regulatory Guide 1.20 (Rev.3, March 2007), we conducted vibration analysis for a steam dryer as the second steam separator of steam generator internals. The vibration analysis was performed at the 100 % power operating condition as the normal operation condition. The random hydraulic loads were calculated by the computational fluid dynamics and the structural responses were predicted by power spectral density analysis for the probabilistic method. In order to meet the recently revised U.S. NRC RG 1.20 Rev.3, the CVAP against the potential adverse flow effects in APR1400 SG internals should be performed. This study conducted the vibration response analysis for the SG steam dryer as the second moisture separator at the 100% power condition, and evaluated the structural integrity. The predicted alternating stress intensities were evaluated to have more than 17.78 times fatigue margin compared to the endurance limit.

Drying of carrot slices in a triple pass solar dryer

Directory of Open Access Journals (Sweden)

Seshachalam Kesavan

2017-01-01

Full Text Available An indirect triple pass forced convection solar dryer was developed and its performance was evaluated for drying of carrot slices. The drying experiments were carried out under the meteorological conditions of Coimbatore city in India during the year 2016. The experimental set-up consists of a blower, triple pass packed bed air collector (using sand with wire mesh absorber plate, and a drying chamber. The air mass flow rate was optimized to 0.062 kg/s. The initial moisture content of the carrot slices was reduced from 87.5% (on wet basis to the final moisture content of 10% (wet basis in 6 h duration. The thin layer drying characteristics were analyzed using twelve mathematical models available in open literature. The results showed that the pick-up efficiency of the dryer was varied in the range between 14 and 43% with an average air collector thermal efficiency of 44% during the experimentation. The drying characteristics of carrot slices was predicted with good degree of accuracy using Wang and Singh drying model.

Mass transfer parameters of celeriac during vacuum drying

Science.gov (United States)

Beigi, Mohsen

2017-04-01

An accurate prediction of moisture transfer parameters is very important for efficient mass transfer analysis, accurate modelling of drying process, and better designing of new dryers and optimization of existing drying process. The present study aimed to investigate the influence of temperature (e.g., 55, 65 and 75 °C) and chamber pressure (e.g., 0.1, 3, 7, 10, 13 and 17 kPa) on effective diffusivity and convective mass transfer coefficient of celeriac slices during vacuum drying. The obtained Biot number indicated that the moisture transfer in the celeriac slices was controlled by both internal and external resistance. The effective diffusivity obtained to be in the ranges of 7.5231 × 10-10-3.8015 × 10-9 m2 s-1. The results showed that the diffusivity increased with increasing temperature and decreasing pressure. The mass transfer coefficient values varied from 4.6789 × 10-7 to 1.0059 × 10-6 m s-1, and any increment in drying temperature and pressure caused an increment in the coefficient.

The Impedance of Multi-layer Vacuum Chambers

CERN Document Server

Vos, L

2003-01-01

Many components of the LHC vacuum chamber have multi-layered walls : the copper coated cold beam screen, the titanium coated ceramic chamber of the dump kickers, the ceramic chamber of the injection kickers coated with copper stripes, only to name a few. Theories and computer programs are available for some time already to evaluate the impedance of these elements. Nevertheless, the algorithm developed in this paper is more convenient in its application and has been used extensively in the design phase of multi-layer LHC vacuum chamber elements. It is based on classical transmission line theory. Closed expressions are derived for simple layer configurations, while beam pipes involving many layers demand a chain calculation. The algorithm has been tested with a number of published examples and was verified with experimental data as well.

Performance of mechanically shaken indirect contact atmospheric dryer in drying pastelike materials

Directory of Open Access Journals (Sweden)

K. P. Melo

2004-09-01

Full Text Available Pastelike materials are encountered in many technological processes in chemical, pharmaceutical, foodstuff and natural product industries. The most important factor in the drying of this type of materials is the nature of the moisture bonding that occurs. Because of the different characteristics of pastes, it is impossible to recommend a universal type of dryer for all of these materials. Some of the dryers available provide only indirect contact with the drying agent (heat and also maintain constant moisture with a system of rotating paddles. We evaluated the performance of this type by studying the dryer kinetics curves for ground coffee under a variety of operational conditions of moisture load of material, temperature of the heating plate, intensity of the mechanical mixing of the moisture material, and initial moisture. The effects of these parameters (except for moisture were studied using a 2³ factorial design. According the analyses of the kinetics drying curves, was observed that the increase in the temperature of the plate and rotation as well as the decrease in the load facilitates more effective removal of moisture. In statistical analysis was determined that the load of the material and the heating plate temperature influence the final moisture content of the material and plate temperature modifies the final temperature of the solid. Also, was suggested linear models from the factorial design to describe the process of drying coffee grounds satisfactorily.

Hydrogen-Oxygen Reaction Assessment in the HANARO Cold Neutron Source

International Nuclear Information System (INIS)

Choi, Jung Woon; Kim, Hark Rho; Lee, Kye Hong; Han, Young Soo; Kim, Young Ki; Kim, Seok Hoon; Jeong, Jong Tae

2006-04-01

Liquid hydrogen, filled in the moderator cell of the in-pool assembly (IPA), is selected as a moderator to moderate thermal neutrons into cold neutrons for the HANARO Cold Neutron Source. Since the IPA will be installed in the vertical CN hole of the reflector tank at HANARO, the vacuum chamber (VC), the pressure boundary against the reactor, should withstand the detonation pressure so as to avoid any physical damage on the reactor under the hydrogen-oxygen chemical reaction. Accordingly, not only will the vacuum chamber be designed to keep its integrity against the hydrogen accident, but also the hydrogen and vacuum system will be designed with the leak-tight concept and also designed to be surrounded by the inert gas blanket system to prevent any air intrusion into the system. Also, in order to confirm the design concept of the CNS as well as VC integrity against the hydrogen accident, the hydrogen-oxygen chemical reaction is evaluated in this report by several methodologies: AICC methodology, Equivalent TNT detonation methodology, Explosion test result, and Calculation of VC strain under the maximum reflected explosion load

Hydrogen-Oxygen Reaction Assessment in the HANARO Cold Neutron Source

Energy Technology Data Exchange (ETDEWEB)

Choi, Jung Woon; Kim, Hark Rho; Lee, Kye Hong; Han, Young Soo; Kim, Young Ki; Kim, Seok Hoon; Jeong, Jong Tae

2006-04-15

Liquid hydrogen, filled in the moderator cell of the in-pool assembly (IPA), is selected as a moderator to moderate thermal neutrons into cold neutrons for the HANARO Cold Neutron Source. Since the IPA will be installed in the vertical CN hole of the reflector tank at HANARO, the vacuum chamber (VC), the pressure boundary against the reactor, should withstand the detonation pressure so as to avoid any physical damage on the reactor under the hydrogen-oxygen chemical reaction. Accordingly, not only will the vacuum chamber be designed to keep its integrity against the hydrogen accident, but also the hydrogen and vacuum system will be designed with the leak-tight concept and also designed to be surrounded by the inert gas blanket system to prevent any air intrusion into the system. Also, in order to confirm the design concept of the CNS as well as VC integrity against the hydrogen accident, the hydrogen-oxygen chemical reaction is evaluated in this report by several methodologies: AICC methodology, Equivalent TNT detonation methodology, Explosion test result, and Calculation of VC strain under the maximum reflected explosion load.

Experiences on vacuum conditioning in the cryostat of KSTAR tokamak

Energy Technology Data Exchange (ETDEWEB)

Kim, Kwang Pyo, E-mail: kpkim@nfri.er.ke [National Fusion Research Institute, Daejeon (Korea, Republic of); Woo, I.S.; Chang, Y.B.; Kwag, S.W.; Song, N.H.; Bang, E.N.; Hong, J.S.; Chu, Y.; Park, K.R. [National Fusion Research Institute, Daejeon (Korea, Republic of)

2013-10-15

Highlights: ► The vacuum of the cryostat has been stably maintained during the KSTAR operation. ► The detected cold leak at the PF/CS coils and CS structure. ► The present helium leak makes no issue for the cryostat operation. -- Abstract: Korea Superconducting Tokamak Advanced Research (KSTAR) device has been successfully operated for the plasma experiment from KSTAR 1st campaign to 4th campaign. The main pumping system for the cryostat has to maintain the target pressure below 1.0 × 10{sup −4} mbar at room temperature and 1.0 × 10{sup −5} mbar at extremely low temperature for the plasma experiment against the air leak coming from ports of vessel and/or the helium leak from cooling loops in the cryostat. No leak has been detected at room temperature. Unexpectedly, the cold-leak appeared in the cryostat at temperature around 50 K during the cool-down in the KSTAR 2nd campaign. We carefully analyzed the characteristics of detected cold leak because it can cause the increase of the base pressure in the cryostat. After the cool-down, the leak detection was performed to locate the position and size of the leak by the pressurizing the loops. As a result, it is found that the cold leak was located at cooling loops for PF/CS coils and CS structure. Nevertheless, the vacuum inside the cryostat was well maintained below 6.0 × 10{sup −8} mbar during the entire operation period. The impact of the He-leak in present status on the plasma operation is negligible. However, we have found that the leak rate increases as a function of time. Therefore careful monitoring on cold-leak is an important technical issue for the operation of superconducting tokamak.

Control of biological hazards in cold smoked salmon production

DEFF Research Database (Denmark)

Huss, Hans Henrik; Embarek, Peter Karim Ben; Jeppesen, V.F.

1995-01-01

An outline of the common processing technology for cold smoked salmon in Denmark is presented. The safety hazards related to pathogenic bacteria, parasites and biogenic amines are discussed with special emphasis on hazards related to Clostridium botulinum and Listeria monocytogenes. Critical...... control points are identified for all hazards except growth of L. monocytogenes. For this reason a limitation of shelf life to three weeks at +5 degrees C far cold smoked vacuum-packed salmon having greater than or equal to 3% water phase salt is recommended...

Life cycle energy metrics and CO 2 credit analysis of a hybrid photovoltaic/thermal greenhouse dryer

OpenAIRE

P. Barnwal; G. N. Tiwari

2008-01-01

In this paper, life cycle energy metrics, such as energy payback time (EPBT), energy production factor (EPF) and life cycle conversion efficiency (LCCE), and mitigation of CO 2 emissions for a hybrid photovoltaic/thermal (PV/T) greenhouse dryer have been analyzed. The hybrid PV/T greenhouse (roof type even span) dryer, designed and constructed at Solar Energy Park, Indian Institute of Technology, New Delhi (28°35′N, 77°12′E, 216 m above MSL), India, has a 2.50 m × 2.60 m floor area, 1.80 m ce...

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

International Nuclear Information System (INIS)

Othieno, H.

1987-01-01

The African Energy Programme (AEP) was established by the Commonwealth Science Council (CSC) to strengthen Africa's scientific and technical capabilities to develop and utilise the continent's enormous renewable energy resources to assist its socio-economic development. The AEP was conceived at a regional workshop held at Arusha, Tanzania in 1979, at which African researchers met to share their experiences of and explored the feasibility of establishing a collaborative regional R and D programme to develop and adapt technologies appropriate to the specific needs of the participating countries. The AEP researchers accorded the highest priority to seeking solutions to the energy problems of Africa's predominantly rural populations and identified eight project areas as the nodes for regional collaborative research and development: 1. Biogas for rural development; 2. Wood/Charcoal production and utilisation; 3. Solar crop drying; 4. Solar thermal heating and cooling; 5. Wind electricity generation; 6. Wind water pumping; 7. Resources Assessments; 8. Energy policy and planning. The primary goal of the AEP activities were to develop indigenous national capabilities to enable the examination and application of technological solutions appropriate to the unique problems and socio-cultural environments of each country. However, the severe limitations on expertise and the broad similarity of many of the critical problems favoured regional R and D cooperation around common techniques and methodologies in each project area. This work has made a significant contribution to Science and Technology. Prior to this work there was no detailed information in natural convection solar dryers. This work has exposed a number of critical design factors which must be considered in order to design an efficient dryer. Buoyancy-induced pressure inside the dryer, problems of multiple radiative heat exchange in the heater and cooling effects of wind have been studied in detail. The final dryer

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

Energy Technology Data Exchange (ETDEWEB)

Othieno, H [Kenyatta University, Nairobi (Kenya)

1987-07-01

The African Energy Programme (AEP) was established by the Commonwealth Science Council (CSC) to strengthen Africa's scientific and technical capabilities to develop and utilise the continent's enormous renewable energy resources to assist its socio-economic development. The AEP was conceived at a regional workshop held at Arusha, Tanzania in 1979, at which African researchers met to share their experiences of and explored the feasibility of establishing a collaborative regional R and D programme to develop and adapt technologies appropriate to the specific needs of the participating countries. The AEP researchers accorded the highest priority to seeking solutions to the energy problems of Africa's predominantly rural populations and identified eight project areas as the nodes for regional collaborative research and development: 1. Biogas for rural development; 2. Wood/Charcoal production and utilisation; 3. Solar crop drying; 4. Solar thermal heating and cooling; 5. Wind electricity generation; 6. Wind water pumping; 7. Resources Assessments; 8. Energy policy and planning. The primary goal of the AEP activities were to develop indigenous national capabilities to enable the examination and application of technological solutions appropriate to the unique problems and socio-cultural environments of each country. However, the severe limitations on expertise and the broad similarity of many of the critical problems favoured regional R and D cooperation around common techniques and methodologies in each project area. This work has made a significant contribution to Science and Technology. Prior to this work there was no detailed information in natural convection solar dryers. This work has exposed a number of critical design factors which must be considered in order to design an efficient dryer. Buoyancy-induced pressure inside the dryer, problems of multiple radiative heat exchange in the heater and cooling effects of wind have been studied in detail. The final dryer

Meat Processing Plant Microbiome and Contamination Patterns of Cold-Tolerant Bacteria Causing Food Safety and Spoilage Risks in the Manufacture of Vacuum-Packaged Cooked Sausages.

Science.gov (United States)

Hultman, Jenni; Rahkila, Riitta; Ali, Javeria; Rousu, Juho; Björkroth, K Johanna

2015-10-01

Refrigerated food processing facilities are specific man-made niches likely to harbor cold-tolerant bacteria. To characterize this type of microbiota and study the link between processing plant and product microbiomes, we followed and compared microbiota associated with the raw materials and processing stages of a vacuum-packaged, cooked sausage product affected by a prolonged quality fluctuation with occasional spoilage manifestations during shelf life. A total of 195 samples were subjected to culturing and amplicon sequence analyses. Abundant mesophilic psychrotrophs were detected within the microbiomes throughout the different compartments of the production plant environment. However, each of the main genera of food safety and quality interest, e.g., Leuconostoc, Brochothrix, and Yersinia, had their own characteristic patterns of contamination. Bacteria from the genus Leuconostoc, commonly causing spoilage of cold-stored, modified-atmosphere-packaged foods, were detected in high abundance (up to >98%) in the sausages studied. The same operational taxonomic units (OTUs) were, however, detected in lower abundances in raw meat and emulsion (average relative abundance of 2%±5%), as well as on the processing plant surfaces (food safety concerns related to their resilient existence on surfaces. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Drying of Rhinacanthus nasutus (Linn. Kurz. using a solar dryer incorporated with a backup thermal energy storage from wood combustion

Directory of Open Access Journals (Sweden)

Perapong Tekasakul

2006-05-01

Full Text Available An indirect, natural convection, solar cabinet dryer incorporated with a backup thermal energy storage from wood combustion was designed and tested with the Thai herb, Rhinacanthus nasutus (Linn. Kurz. Most of Thai herbs are widely used as traditional medicine and drying is an initial step in the production process. Solar dryer with a biomass backup heating system is the most feasible solution to drying in Thailand. In this work, a 4 m x 5 m solar collector was used to absorb solar radiation for heating the incoming air during the daytime, while a biomass burner was used to supply heat when solar energy was not possible. Heat from fuelwood combustion was accumulated in the thermal storage system made of bricks, and was used to heat up the incoming air. Results showed that the herb was dried uniformly and the temperature inside the drying cabinet could be maintained above 50ºC for more than 10 hours. Thermal efficiency when using solar energy was 10.5%, but the value was less than 1% when using the heat from biomass burning. This resulted from the low moisture content of the products after being dried by the solar energy. The dryer is beneficial to the operators, particularly in southern Thailand, where continuous drying is required. This dryer is by no means limited to drying of the herb. Currently, four dryers of the same model have been used by farmer groups in southern Thailand for drying bananas, several types of herbs, fish, and other products. In economic consideration, its payback period is 5.5 years when compared with the LPG-equipped dryer. When the total cost and production capacity are considered, its payback period is about 6 years.

Microstructure and Transparent Super-Hydrophobic Performance of Vacuum Cold-Sprayed Al2O3 and SiO2 Aerogel Composite Coating

Science.gov (United States)

Li, Jie; Zhang, Yu; Ma, Kai; Pan, Xi-De; Li, Cheng-Xin; Yang, Guan-Jun; Li, Chang-Jiu

2018-02-01

In this study, vacuum cold spraying was used as a simple and fast way to prepare transparent super-hydrophobic coatings. Submicrometer-sized Al2O3 powder modified by 1,1,2,2-tetrahydroperfluorodecyltriethoxysilane and mixed with hydrophobic SiO2 aerogel was employed for the coating deposition. The deposition mechanisms of pure Al2O3 powder and Al2O3-SiO2 mixed powder were examined, and the effects of powder structure on the hydrophobicity and light transmittance of the coatings were evaluated. The results showed that appropriate contents of SiO2 aerogel in the mixed powder could provide sufficient cushioning to the deposition of submicrometer Al2O3 powder during spraying. The prepared composite coating surface showed rough structures with a large number of submicrometer convex deposited particles, characterized by being super-hydrophobic. Also, the transmittance of the obtained coating was higher than 80% in the range of visible light.

Sanitary condition of electrical hand dryers in toilets of shopping centres in Kraków

Directory of Open Access Journals (Sweden)

Anna Lenart-Boroń

2015-06-01

Full Text Available Introduction. Shopping habits have changed over the past several years and consumers choose shopping centres, where they can spend time and visit restaurants. People usually wash hands before meals, but toilets in shopping centres are visited by hundreds of users every day which makes their cleanliness questionable. Therefore, the aim of this study was to assess the sanitary condition of electrical hand dryers in toilets of the selected shopping centres in Kraków. Material and methods. Air was sampled at the outlet of electrical hand dryers and surface swabs of hand dryers were taken in toilets of five shopping centres. Air sampling was conducted using the MAS-100 impactor. The number of mesophilic bacteria, fungi, actinomycetes, staphylococci and Escherichia coli was determined. The results of air analyses were compared with the limits provided by the Polish Standards on air quality. Results. The number of microorganisms varied between the studied centres. In terms of mesophilic bacteria and fungi the air was unpolluted. The concentration of actinomycetes however significantly exceeded the limits set by the Polish Standards. Numerous Escherichia coli were found both in the air and in swabs in one of the centres. However the number of E. coli and staphylococci did not exceed the minimum infective dose. Conclusions. The studies showed high concentrations of airborne actinomycetes and staphylococci. Also the presence of E. coli in the air and swabs allows the conclusion that legal regulations for concentrations of airborne microorganisms are necessary to make people aware of this problem. However, it was found that using electrical hand dryers does not have impact on human health.

The cold neutron source in DR 3

International Nuclear Information System (INIS)

Jensen, K.; Leth, j.A.

1980-09-01

A description of the cold neutron source in DR 3 is given. The moderator of the cold neutron source is supercritical hydrogen at about 30degK and 15 bar abs. The necessary cooling capacity is supplied by two Philips Stirling B20 cryogenerators. The hydrogen is circulated between the cryogenerators and the in-pile moderator chamber by small fans. The safety of the facility is based on the use of triple containment preventing contact between hydrogen and air. The triple containment is achieved by enclosing the high vacuum system, surrounging the hydrogen system, in a helium blanket. The achieved spectrum of the thermal neutron flux and the gain factor are given as well as the experience from more than 5 years of operation. Finally some work on extension of the facility to operate two cold sources is reported. (author)

Advanced performance of small diaphragm vacuum pumps through the use of mechatronics

Science.gov (United States)

Lachenmann, R.; Dirscherl, J.

Oil-free diaphragm vacuum pumps have proven to be the best way in vacuum generation for the chemical laboratory and they also find increasing use as backing pumps for modern wide-range turbo molecular pumps. The majority of vacuum pumps in practical use pump only a rather small percentage of their lifetime at full gas load. A pump backing a turbo molecular pump does not have to pump a significant gas load when the high-vacuum pump is running at ultimate vacuum pressure. Also, for a vacuum distillation the vacuum pump has to operate at full speed only at the beginning to lower the pressure inside the system to a vacuum level where evaporation starts. In a rather leak-tight system the distillation process continues by evaporating from the hot liquid and condensing at the cold condenser without the need of a mechanical vacuum pump. Rotational speed controlled diaphragm pumps are now available through progress in mechatronics and offer high pumping speed capability for fast pump-down cycles and precise pressure control for distillations. At low gas load the rotational speed can be reduced, improving maintenance intervals, power consumption, noise, vibration and - surprisingly - also ultimate pressure. The different behaviour in pumping speed and ultimate pressure of rotational speed controlled diaphragm pumps in comparison to constant-speed pumps is related to the mechanical properties of the valves and gas dynamics .

The determination of carbon dioxide concentration using atmospheric pressure ionization mass spectrometry/isotopic dilution and errors in concentration measurements caused by dryers.

Science.gov (United States)

DeLacy, Brendan G; Bandy, Alan R

2008-01-01

An atmospheric pressure ionization mass spectrometry/isotopically labeled standard (APIMS/ILS) method has been developed for the determination of carbon dioxide (CO(2)) concentration. Descriptions of the instrumental components, the ionization chemistry, and the statistics associated with the analytical method are provided. This method represents an alternative to the nondispersive infrared (NDIR) technique, which is currently used in the atmospheric community to determine atmospheric CO(2) concentrations. The APIMS/ILS and NDIR methods exhibit a decreased sensitivity for CO(2) in the presence of water vapor. Therefore, dryers such as a nafion dryer are used to remove water before detection. The APIMS/ILS method measures mixing ratios and demonstrates linearity and range in the presence or absence of a dryer. The NDIR technique, on the other hand, measures molar concentrations. The second half of this paper describes errors in molar concentration measurements that are caused by drying. An equation describing the errors was derived from the ideal gas law, the conservation of mass, and Dalton's Law. The purpose of this derivation was to quantify errors in the NDIR technique that are caused by drying. Laboratory experiments were conducted to verify the errors created solely by the dryer in CO(2) concentration measurements post-dryer. The laboratory experiments verified the theoretically predicted errors in the derived equations. There are numerous references in the literature that describe the use of a dryer in conjunction with the NDIR technique. However, these references do not address the errors that are caused by drying.

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-10-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create nine (9) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry FGD technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-04-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create eight (8) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry flue gas desulfurization (FGD) technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

Analysis of the steady-state operation of vacuum systems for fusion machines

International Nuclear Information System (INIS)

Roose, T.R.; Hoffman, M.A.; Carlson, G.A.

1975-01-01

A computer code named GASBAL was written to calculate the steady-state vacuum system performance of multi-chamber mirror machines as well as rather complex conventional multichamber vacuum systems. Application of the code, with some modifications, to the quasi-steady tokamak operating period should also be possible. Basically, GASBAL analyzes free molecular gas flow in a system consisting of a central chamber (the plasma chamber) connected by conductances to an arbitrary number of one- or two-chamber peripheral tanks. Each of the peripheral tanks may have vacuum pumping capability (pumping speed), sources of cold gas, and sources of energetic atoms. The central chamber may have actual vacuum pumping capability, as well as a plasma capable of ionizing injected atoms and impinging gas molecules and ''pumping'' them to a peripheral chamber. The GASBAL code was used in the preliminary design of a large mirror machine experiment--LLL's MX

Evaluating the parameters of a mobile maize dryer in practice

Directory of Open Access Journals (Sweden)

Josef Los

2013-01-01

Full Text Available The method of drying maize for grain has been recently employed on a large scale in the Czech Republic not only thanks to new maize hybrids but also thanks to the existence of new models of drying plants. One of the new post-harvest lines is a plant in Lipoltice (mobile dryer installed in 2010, storage base in 2012 where basic operational measurements were made of the energy intensiveness of drying and operating parameters of the maize dryer were evaluated. The process of maize drying had two stages, i.e. pre-drying from the initial average grain humidity of 28.55% to 19.6% in the first stage, and the additional drying from 16.7% to a final storage grain humidity of 13.7%. Mean volumes of natural gas consumed per 1 t% for drying in the first and second stage amounted to 1.275 m3 and 1.56 m3, respectively. The total mean consumption of electric energy per 1 t% was calculated to be 1.372 kWh for the given configuration of the post-harvest line.

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

International Nuclear Information System (INIS)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C.; Amador C, C.; Sosa F, W.

2015-09-01

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

Energy Technology Data Exchange (ETDEWEB)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C. [Westinghouse Electric Company LLC, Cranberry Township, PA 16066 (United States); Amador C, C.; Sosa F, W., E-mail: forsytdr@westinghouse.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Km 42.5 Carretera Cardel-Nautla, 91680 Alto Lucero, Veracruz (Mexico)

2015-09-15

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Absolute atomic oxygen and nitrogen densities in radio-frequency driven atmospheric pressure cold plasmas: Synchrotron vacuum ultra-violet high-resolution Fourier-transform absorption measurements

International Nuclear Information System (INIS)

Niemi, K.; O'Connell, D.; Gans, T.; Oliveira, N. de; Joyeux, D.; Nahon, L.; Booth, J. P.

2013-01-01

Reactive atomic species play a key role in emerging cold atmospheric pressure plasma applications, in particular, in plasma medicine. Absolute densities of atomic oxygen and atomic nitrogen were measured in a radio-frequency driven non-equilibrium plasma operated at atmospheric pressure using vacuum ultra-violet (VUV) absorption spectroscopy. The experiment was conducted on the DESIRS synchrotron beamline using a unique VUV Fourier-transform spectrometer. Measurements were carried out in plasmas operated in helium with air-like N 2 /O 2 (4:1) admixtures. A maximum in the O-atom concentration of (9.1 ± 0.7)×10 20 m −3 was found at admixtures of 0.35 vol. %, while the N-atom concentration exhibits a maximum of (5.7 ± 0.4)×10 19 m −3 at 0.1 vol. %

Process analysis of biofuelled heat and power plants integrated with a flue gas dryer; Processtudie av biobraensleeldade kraftvaermeverk integrerade med roekgastork

Energy Technology Data Exchange (ETDEWEB)

Johansson, Kent; Steinwall, Pontus [Sycon Energikonsult AB, Malmoe (Sweden)

2000-01-01

In this report three different processes for combined heat and power production from biomass have been evaluated and compared. Both economical and technical questions have been investigated. The examined processes are: 1. CFB fuelled with wet biomass; 2. A boiler fuelled with pulverised biomass integrated with a traditional flue gas dryer; and 3. A boiler fuelled with pulverized biomass integrated with a flue gas dryer with a closed loop. All the processes have a district heat output of 80 MW. Calculations have been made at three different loads: 100, 70 and 40 % respectively. The performance characteristics in form of electric efficiency and fuel utilisation are very similar for the processes. To evaluate the thermodynamic differences between the processes, calculations have been made with extreme temperatures in the district heating net, 65 deg C/100 deg C. The process with a closed loop drier has a saturation temperature in the flue gas of 95 deg C. Therefore this process has a high fuel utilization even if the incoming water has a high temperature. The fuel utilization for alternatives 1 and 2 decreases almost down to the efficiency of the furnace. This shows that the temperature of the water is too high to recapture the latent heat in the flue gases. The investment costs for the processes have been estimated. Also these are very similar for the three alternatives. The cost for the process with the CFB is 412 million SEK. The boiler in alternative 2 and 3 is approximately 20 million SEK cheaper than the CFB. The decreased cost for the boiler is compensated by the cost for the dryers. The investment cost for the traditional dryer has been estimated to 20 million SEK and 30 million SEK for the closed loop dryer. The total cost for alternative 2 is then 417 million SEK and 414 million SEK for alternative 3. Operation and maintenance costs for the processes with dryer are supposed to be 1 respectively 1.5 million SEK higher than for alternative 1. The dryers may

A novel rate of the reaction between NaOH with CO2 at low temperature in spray dryer

Directory of Open Access Journals (Sweden)

Yadollah Tavan

2017-03-01

Full Text Available Carbon dioxide (CO2 is an influential greenhouse gas that has a significant impact on global warming partly. Nowadays, many techniques are available to control and remove CO2 in different chemical processes. Since the spray dryer has high removal efficiency rate, a laboratory-scale spray dryer is used to absorb carbon dioxide from air in aqueous solution of NaOH. In the present study, the impact of NaOH concentration, operating temperature and nozzle diameter on removal efficiency of CO2 is explored through experimental study. Moreover, the reaction kinetic of NaOH with CO2 is studied over the temperature range of 50–100 °C in a laboratory-scale spray dryer absorber. In the present contribution, a simple reaction rate equation is proposed that shows the lowest deviation from the experimental data with error less than 2%.

ANALISIS KELAYAKAN TEKNIS DAN FINANSIAL DARI INVESTASI PENGADAAN TRAY DRYER BERBAHAN BAKAR BIOMASSA PADA USAHA ARANG TEMPURUNG KELAPA BERBASIS EKSPOR (Studi Kasus di Tropica Nucifera Industry – Yogyakarta

Directory of Open Access Journals (Sweden)

Fanny Widadie

2013-11-01

Full Text Available The purpose of the study is to assess the technical and financial feasibility of procurement investment Tray Dryer fueled biomass to operations of coconut shell charcoal briquette in PT. Tropica Nucifera Industry. The result showed that investment-Tray Dryer on cocnut shell charcoal briquette bussiness was highly feasibile both the technical and financial aspects. The technical aspect was seen that the quantity-production capabilities of coconut shell charcoal briquettes using a dryer-Tray Dryer could be increased 15 percent compared the previous consdition-used of solar energy. While the quality of the charcoal briquettes produced from Tray Dryer was a much butter quality, moisture content (6.39%; ash (2.65%; carbon-bound (85.83%, compared to using sunlight, water content (15.89; ash (2.57% and carbon-bound (77.32%.The financial aspects of procurement Tray Dryer investment that its value was more feasible than previous, nothing Tray Dryer. Coconut shell charcoal briquet enterprises without using Tray Dryer was feasible to be done with NPV 1,058,928.12, IRR 63%, Payback Period 1 year and 9 moths, Net B/C 2.25 and analysis of swicthcing value reached 20 percent. And after the business using Tray Drayer, the financial analysis was much more feasible with NPV 2,285,500,498.12, IRR 113%, Payback Period 11 months, Net B/C 3.5 and analysis of switching value reached 50 percent.

Experimental investigation and thermodynamic performance analysis of a solar dryer using an evacuated-tube air collector

International Nuclear Information System (INIS)

Lamnatou, Chr.; Papanicolaou, E.; Belessiotis, V.; Kyriakis, N.

2012-01-01

Highlights: ► We evaluate an evacuated-tube solar air collector and use it to develop a novel dryer. ► Apple, carrot and apricot thin-layer drying experiments are conducted. ► Best overall fitting among several available thin-layer drying models is pursued. ► Thermodynamic analysis yields optimal collector area, energy utilization/exergy loss. ► The proposed dryer has a capacity for drying larger quantities of products. -- Abstract: The present work presents a thermodynamic performance analysis of a solar dryer with an evacuated-tube collector. Drying experiments for apples, carrots and apricots were conducted, after a preliminary stage of the investigation which included measurements for the determination of the collector efficiency. These results showed that the warm outlet air of the collector attains temperature levels suitable for drying of agricultural products without the need of preheating. Thus, the present collector was used as the heat source for a drying chamber in the frame of the development of a novel, convective, indirect solar dryer; given the fact that in the literature there are only a few studies about this type of collectors in conjunction with solar drying applications. Thin-layer drying models were fitted to the experimental drying curves, including the recent model of Diamante et al. which showed good correlation coefficients for all the tested products. Drying parameters such as moisture ratio and drying rates were calculated. Furthermore, an energetic/exergetic analysis of the dryer was also conducted and performance coefficients such as pick-up and exergy efficiencies, energy utilization ratio, exergy losses were determined for several configurations such as single and double-trays and several drying air velocities. On the other hand, an optimal collector surface area study was conducted, based on laws for minimum entropy generation. Design parameters such as optimum collector area were determined based on the minimum entropy

Vacuum technology issues for the SSC [Superconducting Super Collider

International Nuclear Information System (INIS)

Joestlein, H.

1989-01-01

The Superconducting Super Collider, to be built in Texas, will provide an energy of 40 TeV from colliding proton beams. This energy is twenty times higher than currently available from the only other cryogenic collider, the Fermilab Tevatron, and will allow experiments that can lead to a better understanding of the fundamental properties of matter. The energy scale and the size of the new machine pose intriguing challenges and opportunities for the its vacuum systems. The discussion will include the effects of synchrotron radiation on cryogenic beam tubes, cold adsorption pumps for hydrogen, methods of leak checking large cryogenic systems, the development of cold beam valves, and radiation damage to components, especially electronics. 9 figs., 1 tab

Experimental study of regenerative desiccant integrated solar dryer with and without reflective mirror

Energy Technology Data Exchange (ETDEWEB)

Shanmugam, V. [Department of Mechanical Engineering, Sathyabama University, Chennai, 600 119 (India); Natarajan, E. [Institute for Energy Studies, College of Engineering, Anna University, Chennai, 600 025 (India)

2007-06-15

An indirect forced convection with desiccant integrated solar dryer has been built and tested. The main parts are: a flat plate solar air collector, a drying chamber, desiccant bed and a centrifugal blower. The system is operated in two modes, sunshine hours and off sunshine hours. During sun shine hours the hot air from the flat plate collector is forced to the drying chamber for drying the product and simultaneously the desiccant bed receives solar radiation directly and through the reflected mirror. In the off sunshine hours, the dryer is operated by circulating the air inside the drying chamber through the desiccant bed by a reversible fan. The dryer is used to dry 20 kg of green peas and pineapple slices. Drying experiments were conducted with and without the integration of desiccant unit. The effect of reflective mirror on the drying potential of desiccant unit was also investigated. With the inclusion of reflective mirror, the drying potential of the desiccant material is increased by 20% and the drying time is reduced. The drying efficiency of the system varies between 43% and 55% and the pick-up efficiency varies between 20% and 60%, respectively. Approximately in all the drying experiments 60% of moisture is removed by air heated using solar energy and the remainder by the desiccant. The inclusion of reflective mirror on the desiccant bed makes faster regeneration of the desiccant material. (author)

PADDY DRYING IN MIXED ADSORPTION DRYER WITH ZEOLITE: DRYING RATE AND TIME ESTIMATION

Directory of Open Access Journals (Sweden)

Mochammad Djaeni

2013-11-01

Full Text Available Recently, the main problem of the rice stock and distribution in Indonesia is the quality degradation as indicated in unpleasant odor (smelly, stained, yellowness, and high percentage of broken rice. This is due to the low of paddy quality dried by from either direct sunlight or conventional fluidized bed dryer. As a result, the paddy cracks and breaks easily during milling in which causes the storage life being shorter as the enzymatic degradation by germ or fungi occurs. Air dehumidified with zeolite at drying medium temperature is potential to improve the quality of paddy. Zeolite is a material having high affinity to water vapor. In this case, the paddy and zeolite was mixed and fluidized with the air. The air will evaporate water from paddy, and at same time, the zeolite will adsorb water from air. Hence, the humidity of dryer can be kept low in which improves the driving force for drying. This work discusses the effect of presence of zeolite in the dryer, operational drying temperature, air velocity and relative humidity on drying rate of paddy. The results showed that increasing of zeolite as well as operational temperature increased the drying rate. In addition, using the model, the air dehumidification with zeolite and increase of air velocity can speed up drying time significantly at operational temperature below 80oC. This condition is very suitable for paddy drying since the quality degradation can be avoided.

LHC vacuum upgrade during LS1

International Nuclear Information System (INIS)

Jimenez, J.M.; Baglin, V.; Chiggiato, P.; Cruikshank, P.; Gallilee, M.; Garion, C.; Gomes, P.

2012-01-01

The last two years of LHC operation have highlighted concerns on the levels of the dynamic vacuum in the long straight sections in presence of high intensity beams. The analysis of the existing data has shown relationship between pressures spikes and beam screen temperature oscillations or micro-sparking in the RF fingers of the bellows on one side and coincidence of pressure bumps with stimulated desorption by electron cloud, beam losses and/or thermal out gassing stimulated by higher order modes (HOM) losses. The electron cloud mitigation solutions will be adapted to the different configurations: cold/warm transitions, non-coated surfaces in direct view of beams, photoelectrons, etc. All scenarios will be presented together with their efficiencies. Additional pumping and re-engineering of components will reduce the sensitivity of the vacuum system to beam losses or HOM inducing out gassing. The expected margin at nominal intensity and energy resulting from these consolidations will be summarized. Finally, the challenges of the Experimental areas will be addressed, more specifically the status of the new Beryllium pipes (ATLAS and CMS) which are in the critical path and the consolidation of vacuum instrumentation, pumping and electron cloud mitigation. The risk corresponding to the proposed consolidations will be shown and the margins with respect to the schedule analysed. (authors)

Saving energy. [Metal Coating With Infrared Dryers

Energy Technology Data Exchange (ETDEWEB)

Schmid, K

1981-01-01

One way of saving energy in metal coating is by using electrically heated infrared dryers with medium-wave radiation (2 to 3 ..mu..m). The absorbing capacity of varnishes and plastic coatings is >90% in this range so that the radiation energy is almost completely transformed into heat. Medium-wave radiation sources have a much higher service life than short-wave sources (30.000 hours of operation) and do not require cooling; compared with long-wave sources, they have a higher heat transfer and thus much shorter drying times. The main fields of application, a cost example, and practical examples among the customers of Messrs. Eisenmann are presented.

Design and Performance Evaluation of a Solar Assisted Heat Pump Dryer Integrated with Biomass Furnace for Red Chilli

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performance of a solar assisted heat pump dryer integrated with biomass furnace has been designed and evaluated for drying red chillies, and drying kinetics of red chillies were evaluated. The red chillies were dried from 22 kg with moisture content of 4.26 db to moisture content of 0.08 db which needed 11 hours, with the average drying chamber temperature, drying chamber relative humidity, and an air mass flow rate of 70.5°C, 10.1%, and 0.124 kg/s, respectively, while the open sun drying needed 62 hours. Compared to open sun drying, this dryer yielded 82% saving in drying time. The drying rate, the specific moisture extraction rate, and thermal efficiency of the dryer were estimated in average to be about 1.57 kg/h, 0.14 kg/kWh, and 9.03%, respectively. Three mathematical models, the Newton, Henderson-Pabis, and Page models, were fitted to the experimental data on red chillies dried by solar assisted heat pump dryer integrated with biomass furnace and open sun drying. The performance of these models was evaluated by comparing the coefficient of determination (R2, mean bias error (MBE, and root mean-square error (RMSE. The Page model gave the best results for representing drying kinetics of red chillies.

Modelling of hot air chamber designs of a continuous flow grain dryer

DEFF Research Database (Denmark)

Kjær, Lotte Strange; Poulsen, Mathias; Sørensen, Kim

2018-01-01

The pressure loss, flow distribution and temperature distribution of a number of designs of the hot air chamber in a continuous flow grain dryer, were investigated using CFD. The flow in the dryer was considered as steady state, compressible and turbulent. It is essential that the grain...... is uniformly dried as uneven drying can result in damage to the end-product during storage. The original commercial design was modified with new guide vanes at the inlets to reduce the pressure loss and to ensure a uniform flow to the line burner in the hot air chamber. The new guide vane design resulted...... in a 10% reduction in pressure loss and a γ-value of 0.804. Various design changes of the hot air chamber were analysed in terms of pressure loss and temperature distribution with the aim of a temperature variation of 5 K at the outlet ducts. An obstruction design was analysed, which improved mixing...

Design aspects of integrated compact thermal storage system for solar dryer applications

International Nuclear Information System (INIS)

Rajaraman, R.; Velraj, R.; Renganarayanan, S.

2000-01-01

Solar energy is an excellent source for drying of crops, fruits, vegetables and other agricultural and forest products. Though the availability of solar energy is plenty, it is time dependent in nature. The energy need for some applications is also time dependent, but in a different pattern and phase from the solar energy supply. This implies that the solar dryer should be integrated with an efficient thermal storage system to match the time-dependent supply and end-use requirements. Based on the studies carried out on Latent Heat Thermal Storage (LHTS) Systems, it is observed that when air is used as the heat transfer fluid in LHTS system, nearly uniform surface heat flux can be achieved. Hence the LHTS systems are most suitable for air based solar drying applications. In the present work some major conclusions arrived from the investigations on LHTS systems and the design considerations for the integrated latent heat thermal storage for the solar dryer are reported. (Author)

Spent nuclear fuel project, Cold Vacuum Drying Facility human factors engineering (HFE) analysis: Results and findings

International Nuclear Information System (INIS)

Garvin, L.J.

1998-01-01

This report presents the background, methodology, and findings of a human factors engineering (HFE) analysis performed in May, 1998, of the Spent Nuclear Fuels (SNF) Project Cold Vacuum Drying Facility (CVDF), to support its Preliminary Safety Analysis Report (PSAR), in responding to the requirements of Department of Energy (DOE) Order 5480.23 (DOE 1992a) and drafted to DOE-STD-3009-94 format. This HFE analysis focused on general environment, physical and computer workstations, and handling devices involved in or directly supporting the technical operations of the facility. This report makes no attempt to interpret or evaluate the safety significance of the HFE analysis findings. The HFE findings presented in this report, along with the results of the CVDF PSAR Chapter 3, Hazards and Accident Analyses, provide the technical basis for preparing the CVDF PSAR Chapter 13, Human Factors Engineering, including interpretation and disposition of findings. The findings presented in this report allow the PSAR Chapter 13 to fully respond to HFE requirements established in DOE Order 5480.23. DOE 5480.23, Nuclear Safety Analysis Reports, Section 8b(3)(n) and Attachment 1, Section-M, require that HFE be analyzed in the PSAR for the adequacy of the current design and planned construction for internal and external communications, operational aids, instrumentation and controls, environmental factors such as heat, light, and noise and that an assessment of human performance under abnormal and emergency conditions be performed (DOE 1992a)

Laser-Free Cold-Atom Gymnastics

Science.gov (United States)

Gould, Harvey; Feinberg, Benedict; Munger, Charles T., Jr.; Nishimura, Hiroshi

2017-01-01

We have performed beam transport simulations on ultra cold (2 μK) and cold (130 μK) neutral Cs atoms in the F = M = + 4 (magnetic weak-field seeking) ground state. We use inhomogeneous magnetic fields to focus and accelerate the atoms. Acceleration of neutral atoms by an inhomogeneous magnetic field was demonstrated by Stern and Gerlach in 1922. In the simulations, a two mm diameter cloud of atoms is released to fall under gravity. A magnetic coil focuses the falling atoms. After falling 41 cm, the atoms are reflected in the magnetic fringe field of a solenoid. They return to their starting height, about 0.7 s later, having passed a second time through the focusing coil. The simulations show that > 98 % of ultra cold Cs atoms and > 70 % of cold Cs atoms will survive at least 15 round trips (assuming perfect vacuum). More than 100 simulations were run to optimize coil currents and focusing coil diameter and height. Simulations also show that atoms can be launched into a fountain. An experimental apparatus to test the simulations, is being constructed. This technique may find application in atomic fountain clocks, interferometers, and gravitometers, and may be adaptable for use in microgravity. It may also work with Bose-Einstein condensates of paramagnetic atoms.

Influence of drying conditions on the effective diffusivity and activation energy during convective air and vacuum drying of pumpkin

Directory of Open Access Journals (Sweden)

Liliana SEREMET (CECLU

2015-12-01

Full Text Available The main purpose of the work is to investigate the efficiency of convective air and vacuum processing on pumpkin drying kinetics. The pumpkin samples were of two different geometrical shapes (cylinder and cube and were dried in a laboratory scale hot air dryer using some specific parameters (constant air velocity of 1.0 m/s, three different temperatures 50, 60 and 70ºC suited to relative humidity (RH values of 9.8, 6.5, and 5.4% respectively. The vacuum drying was led at constant pressures of 5 kPa and accordance temperatures of 50, 60 and 70ºC. Moisture transfer from pumpkin slices was described by applying Fick’s diffusion model. Temperature dependence of the effective diffusivity was described by the Arrhenius-type equation. Cylindrical samples have a slightly better behaviour compared to cubic samples, due to the disposition of the tissues, and the mass and thermic transfer possibilities. Analysing the results of both drying methods, it was deduced that the most efficient method is convective air drying at 70ºC.

Effect of drying method on the adsorption isotherms and isosteric heat of passion fruit pulp powder

Directory of Open Access Journals (Sweden)

Maria Angélica Marques Pedro

2010-12-01

Full Text Available The sorption behavior of dry products is generally affected by the drying method. The sorption isotherms are useful to determine and compare thermodynamic properties of passion fruit pulp powder processed by different drying methods. The objective of this study is to analyze the effects of different drying methods on the sorption properties of passion fruit pulp powder. Passion fruit pulp powder was dehydrated using different dryers: vacuum, spray dryer, vibro-fluidized, and freeze dryer. The moisture equilibrium data of Passion Fruit Pulp (PFP powders with 55% of maltodextrin (MD were determined at 20, 30, 40 and 50 ºC. The behavior of the curves was type III, according to Brunauer's classification, and the GAB model was fitted to the experimental equilibrium data. The equilibrium moisture contents of the samples were little affected by temperature variation. The spray dryer provides a dry product with higher adsorption capacity than that of the other methods. The vibro-fluidized bed drying showed higher adsorption capacity than that of vacuum and freeze drying. The vacuum and freeze drying presented the same adsorption capacity. The isosteric heats of sorption were found to decrease with increasing moisture content. Considering the effect of drying methods, the highest isosteric heat of sorption was observed for powders produced by spray drying, whereas powders obtained by vacuum and freeze drying showed the lowest isosteric heats of sorption.

Drying of Rosella (Hibiscus sabdariffa Flower Petals using Solar Dryer with Double Glass Cover Collector

Directory of Open Access Journals (Sweden)

Tjukup Marnoto

2014-10-01

Full Text Available Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture content of 90.84 % be dried with this dryer until the moisture content of 7.67 % takes only 2 days, although the weather was less sunny . The temperature in the drying chamber was not more than 50° C, so it was good for drying groceries, not damaging chemical ingredients. The relative humidity in the space dryeris was about 40 % and it was still relative low. Drying rate and drying performance was expressed by the efficiency and Specific Moisture Evaporation Rate ( SMER were influenced by water content of the dried material and weather. Daily efficiency at the first and the second day: 14.931 % and 5.78%, while the daily SMER on the first and the second day: 0.222 and 0.0256 ( kg / kWh .

Final Report: Laboratory Development of a High Capacity Gas-Fired Paper Dryer

Energy Technology Data Exchange (ETDEWEB)

Yaroslav Chudnovsky; Aleksandr Kozlov; Lester Sherrow

2005-09-30

Paper drying is the most energy-intensive and temperature-critical aspect of papermaking. It is estimated that about 67% of the total energy required in papermaking is used to dry paper. The conventional drying method uses a series of steam-heated metal cylinders that are required to meet ASME codes for pressure vessels, which limits the steam pressure to about 160 psig. Consequently, the shell temperature and the drying capacity are also limited. Gas Technology Institute together with Boise Paper Solutions, Groupe Laperrier and Verreault (GL&V) USA Inc., Flynn Burner Corporation and with funding support from the U.S. Department of Energy, U.S. natural gas industry, and Gas Research Institute is developing a high efficiency gas-fired paper dryer based on a combination of a ribbon burner and advanced heat transfer enhancement technique. The Gas-Fired Paper Dryer (GFPD) is a high-efficiency alternative to conventional steam-heated drying drums that typically operate at surface temperatures in the 300 deg F range. The new approach was evaluated in laboratory and pilot-scale testing at the Western Michigan University Paper Pilot Plant. Drum surface temperatures of more than 400 deg F were reached with linerboard (basis weight 126 lb/3000 ft2) production and resulted in a 4-5 times increase in drying rate over a conventional steam-heated drying drum. Successful GFPD development and commercialization will provide large energy savings to the paper industry and increase paper production rates from dryer-limited (space- or steam-limited) paper machines by an estimated 10 to 20%, resulting in significant capital costs savings for both retrofits and new capacity.

He leaks in the CERN LHC beam vacuum chambers operating at cryogenic temperatures

CERN Document Server

Baglin, V

2007-01-01

The 27 km long large hadron collider (LHC), currently under construction at CERN, will collide protons beam at 14 TeV in the centre of mass. In the 8 arcs, the superconducting dipoles and quadrupoles of the FODO cells operate with superfluid He at 1.9 K. In the 8 long straight sections, the cold bores of the superconducting magnets are held at 1.9 or 4.5 K. Thus, in the LHC, 75% of the beam tube vacuum chamber is cooled with He. In many areas of the machine, He leaks could appear in the beam tube. At cryogenic temperature, the gas condenses onto the cold bores or beam screens, and interacts with the circulating beam. He leaks creates a He front propagating along the vacuum chambers, which might cause magnet quench. We discuss the consequences of He leaks, the possible means of detections, the strategies to localise them and the methods to measure their size.

The study of some physical properties and energy aspects of potatoes drying process by the infrared-vacuum method

Directory of Open Access Journals (Sweden)

N Hafezi

2016-09-01

Full Text Available Introduction Potato (Solanumtuberosum L. is one of the unique and most potential crops having high productivity, supplementing major food requirement in the world. Drying is generally carried out for two main reasons, one to reduce the water activity which eventually increases the shelf life of food and second to reduce the weight and bulk of food for cheaper transport and storage. The quality evaluation of the dried product was carried out on the basis of response variables such as rehydration ratio, shrinkage percentage, color and the overall acceptability. Drying is the most energy intensive process in food industry. Therefore, new drying techniques and dryers must be designed and studied to minimize the energy cost in drying process. Considering the fact that the highest energy consumption in agriculture is associated with drying operations, different drying methods can be evaluated to determine and compare the energy requirements for drying a particular product. Thermal drying operations are found in almost all industrial sectors and are known, according to various estimates, to consume 10-25% of the national industrial energy in the developed world. Infrared radiation drying has the unique characteristics of energy transfer mechanism. Kantrong et al. (2012 were studied the drying characteristics and quality of shiitake mushroom undergoing microwave-vacuum combined with infrared drying. Motevali et al. (2011 were evaluated energy consumption for drying of mushroom slices using various drying methods including hot air, microwave, vacuum, infrared, microwave-vacuum and hot air-infrared. The objectives of this research were to experimental study of drying kinetics considering quality characteristics including the rehydration and color distribution of potato slices in a vacuum- infrared dryer and also assessment of specific energy consumption and thermal utilization efficiency of potato slices during drying process. Materials and Methods A

76 FR 22453 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... Mode and Off Mode b. Automatic Cycle Termination c. Ventless Clothes Dryers d. Consumer Usage Habits e... as cooling capacity in British thermal units (Btu) per hour (h) divided by electrical input power in...

Study on Recrystallization of Cold-worked and β-quenched zirconium alloys

International Nuclear Information System (INIS)

Goo, J. S.; Hong, S. I.; Kim, H. S.; Jeong, Y. H.

1998-01-01

The observation of microstructure and the hardness test of Zr-Sn binary and Zircaloy-4 alloys were performed to investigate the recrystallization of cold-worked and β-quenched Zr alloys. All specimens were heat-treated in vacuum condition at various temperatures. From the observation of microstructures of cold-worked and β-quenched Zr alloys, the cold-worked specimens were shown to keep the cold-worked micro- structure as annealing temperature increased up to 500 deg C and the recrystallization was completed at between 550 deg C and 700 deg C. Meanwhile, the recrystallization of β-quenched Zr alloys was started at about 700 deg C. In all specimens of cold-worked and β-quenched Zr alloys, the hardness value tended to be consistent with microstructure. Although the cold-worked and the β-quenched specimens had an equal initial hardness value, the recrystallization behavior was indicated to be different from each other, which means that recrystallization mechanism is different from each other

Thermal Vacuum Integrated System Test at B-2

Science.gov (United States)

Kudlac, Maureen T.; Weaver, Harold F.; Cmar, Mark D.

2012-01-01

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) Plum Brook Station (PBS) Space Propulsion Research Facility, commonly referred to as B-2, is NASA s third largest thermal vacuum facility. It is the largest designed to store and transfer large quantities of liquid hydrogen and liquid oxygen, and is perfectly suited to support developmental testing of chemical propulsion systems as well as fully integrated stages. The facility is also capable of providing thermal-vacuum simulation services to support testing of large lightweight structures, Cryogenic Fluid Management (CFM) systems, electric propulsion test programs, and other In-Space propulsion programs. A recently completed integrated system test demonstrated the refurbished thermal vacuum capabilities of the facility. The test used the modernized data acquisition and control system to monitor the facility during pump down of the vacuum chamber, operation of the liquid nitrogen heat sink (or cold wall) and the infrared lamp array. A vacuum level of 1.3x10(exp -4)Pa (1x10(exp -6)torr) was achieved. The heat sink provided a uniform temperature environment of approximately 77 K (140deg R) along the entire inner surface of the vacuum chamber. The recently rebuilt and modernized infrared lamp array produced a nominal heat flux of 1.4 kW/sq m at a chamber diameter of 6.7 m (22 ft) and along 11 m (36 ft) of the chamber s cylindrical vertical interior. With the lamp array and heat sink operating simultaneously, the thermal systems produced a heat flux pattern simulating radiation to space on one surface and solar exposure on the other surface. The data acquired matched pretest predictions and demonstrated system functionality.

The effect of vacuum packaging on physicochemical changes in rainbow trout (Oncorhynchus mykiss during cold storage

Directory of Open Access Journals (Sweden)

František Ježek

2014-01-01

Full Text Available The aim of the study was to monitor changes in selected physical (awwater activity, pH values and chemical (TVBN total volatile basic nitrogen, TMA-N trimethylamine nitrogen, FFA free fatty acids, PV peroxide values, TBA thiobarbituric acid value properties in the shelf life of rainbow trout (Oncorhynchus mykiss muscle. A total of 192 trout were examined. Control samples (96 samples were simply packaged in contact with atmospheric oxygen, while experimental samples (96 samples were packaged in a commercial vacuum (98%. All the samples were stored at 2 ± 2° C for 11 days. Analyses were performed on storage days 1, 2, 4, 7, 9, and 11. During the experiment, aw values increased in both types of packaging (in air: 0.982; vacuum-packaged: 0.989. At the end of storage, TVBN and TMA concentrations were at 28.88 ± 4.42 and 19.28 ± 3.00 g mg·100-1, respectively, in the muscle of vacuum-packaged trout; and at 30.52 ± 2.91 and 19.94 ± 2.05 mg·100 g-1, respectively, in fish in simple packaging. The FFA content in vacuum-packaged fish initially declined before increasing to 3.67 ± 2.37% of total fat as oleic acid later in the experiment. The pattern of PV changes was inconclusive, and significant changes (P -1 in vacuum-packaged fish and to 26.03 ± 8.00 mg·kg-1 in fish in simple packaging. Free fatty acids are not a good indicator of spoilage because they are converted to hydroperoxides. Vacuum packaging effectively slowed down oxidative changes in rainbow trout muscle. The peroxide content is not a suitable indicator of shelf life as peroxides are decomposed to secondary products. Total volatile basic nitrogen and thiobarbituric acid value can be recommended as suitable indicators of freshness and shelf life.

Evaluation of an industrial gas-fired IR dryer; Utvaerdering av en industriell gaseldad IR-straalare

Energy Technology Data Exchange (ETDEWEB)

Stenstroem, S; Hermodsson, S

1994-11-01

The IR dryer is used in a paper making machine to dry the paper web after it has been coated with a surface layer. In part 1 of the project a mathematical model have been developed, capable of calculating the radiation intensity and other energy flows in the dryer. In part 2 of the project, measurements have been made on the IR radiator mounted in the paper making machine. The calculation model shows the efficiency of the radiator to 39% at full power and 35% at half power. The direct measurements were made at half power and gave an efficiency of 31% for new radiators and 28% for old ones. The conclusion is that the calculation model values corresponds very well compared with direct measurements.

Integration of cooking and vacuum cooling of carrots in a same vessel

Directory of Open Access Journals (Sweden)

Luiz Gustavo Gonçalves Rodrigues

2012-03-01

Full Text Available Cooked vegetables are commonly used in the preparation of ready-to-eat foods. The integration of cooking and cooling of carrots and vacuum cooling in a single vessel is described in this paper. The combination of different methods of cooking and vacuum cooling was investigated. Integrated processes of cooking and vacuum cooling in a same vessel enabled obtaining cooked and cooled carrots at the final temperature of 10 ºC, which is adequate for preparing ready-to-eat foods safely. When cooking and cooling steps were performed with the samples immersed in boiling water, the effective weight loss was approximately 3.6%. When the cooking step was performed with the samples in boiling water or steamed, and the vacuum cooling was applied after draining the boiling water, water loss ranged between 15 and 20%, which caused changes in the product texture. This problem can be solved with rehydration using a small amount of sterile cold water. The instrumental textural properties of carrots samples rehydrated at both vacuum and atmospheric conditions were very similar. Therefore, the integrated process of cooking and vacuum cooling of carrots in a single vessel is a feasible alternative for processing such kind of foods.

Numerical calculations of heat engineering parameters of a solar greenhouse dryer

International Nuclear Information System (INIS)

Akhatov, Zh.S.; Khalimov, A.S.

2015-01-01

The results of numerical simulation to determine the optimum volume of a thermal storage water heater in a solar greenhouse dryer are presented. A CAD (computer-aided design) model is created for the given installation by simulating the heat transfer processes with the aid of the Solid Works Flow Simulation software. The given CAD model consists of a concrete foundation and a steel frame in which translucent coatings made from two-layer polycarbonate sheets 6 mm in thickness with an air gap between the two layers are attached. The north wall is made of bricks with size and thickness of 2 x 4 m"2 and 0.4 m, respectively. The front surface has an angle of inclination 39.53 degree with respect to the horizontal surface for the maximum incidence of solar radiation to its surface. All the geometrical dimensions of the solar greenhouse dryer were selected on the basis of the allocated platform for the solar drying installation 3 x 4 m"2 in size. It is shown that the optimum volume of the heat storage tank for the present installation is 500 L. (authors)

Effect of brining on the drying rate of tilapia in a solar tunnel dryer

Energy Technology Data Exchange (ETDEWEB)

Kituu, G.M.; Shitanda, D.; Kanali, C.L.; Mailutha, J.T. [Jomo Kenyatta Univ. of Agriculture and Technology, Nairobi (Kenya). BEED

2008-07-01

In addition to being a source of protein, fish is an important source of local and foreign currency earnings in Kenya. A substantial amount of fish production is exported. Approximately 30 per cent is exported to the European Union, the United States, and countries in the Middle East, but nearly half of the total annual fish harvest in Kenya goes to waste due to poor processing and preservation. Measures must be taken to ensure the fish industry is protected and waste is minimized, since the livelihood of over 500,000 people depends on fish as a source of proteins and employment. Therefore, it is necessary to implement appropriate and affordable processing and preservation techniques for fish at the artisanal landing sites in order to reduce the wastage and spoilage of fish during oversupply, and to enhance long storage. This paper presented studies that were conducted to determine the effect of brining on the drying rate of tilapia in a solar tunnel dryer. The paper discussed the materials and methods, including a description of the solar tunnel dryer system; the brining process of fish; the fish drying process; and data analysis. It was concluded that limiting the amount of salt used in brining, and subsequently dehydrating fish with a solar tunnel dryer achieves a more stable and suitable dried fish product than osmotic dehydration or solar drying process separately. 19 refs., 5 figs., 2 appendices.

Design considerations in the use of stainless steel for vacuum and cryogenic equipment

CERN Document Server

Geyari, C

1976-01-01

The properties making austenitic stainless steel a preferred material for the construction of high vacuum equipment are reviewed. Best results are obtained if attention is paid to the improvement of welding properties, particularly with a view to prevent intercrystalline disintegration. A review of mechanical properties, the effect of cold working and cryogenic temperatures on the strength and magnetic characteristics of stainless steel is given. During material selection for very high vacuum, attention must be paid to the porosity problem. A practical example shows the application of these considerations to the choice of materials for the CERN-ISR intersecting storage rings. (19 refs).

Design considerations in the use of stainless steel for vacuum and cryogenic equipment

International Nuclear Information System (INIS)

Geyari, C.

1976-01-01

The properties making austenitic stainless steel a preferred material for the construction of high vacuum equipment are reviewed. Best results are obtained if attention is paid to the improvement of welding properties, particularly with a view to preventing intercrystalline disintegration. A review of mechanical properties, the effect of cold working and cryogenic temperatures on the strength and magnetic characteristics of stainless steel is given. During material selection for very high vacuum, attention must be paid to the porosity problem. A practical example shows the application of these considerations to the choice of materials for the CERN-ISR Intersecting Storage Rings. (author)

Analysis and Testing of a Natural Convection Solar Dryer for the Tropics

Directory of Open Access Journals (Sweden)

A. O. Adelaja

2013-01-01

Full Text Available Solar dryers are imperative for the tropical and sub-Saharan African countries, which are faced with the duo challenges of inadequate electrical energy supply, which has severely limited the application of conventional refrigeration as a means of preservation of agricultural produce, and the need to make produce competitive in the international market. In this study, a cost-effective natural convection solar dryer was developed; the thermal and drying analyses were done and tested to obtain some performance evaluation parameters for the system in order to examine its efficiency and effectiveness by drying some plantain fillets. The collector and system efficiencies are found to be 46.4% and 78.73%, respectively, while a percentage moisture removal of 77.5% was achieved at the 20th hour in order to give final moisture contents of 15.75% in the product, which still maintained its integrity. With a cost of about $195.00, it has been affordable for the small- and medium-scale enterprises as well as for private use in domestic applications.

Energy and rice quality aspects during drying of freshly harvested paddy with industrial inclined bed dryer

International Nuclear Information System (INIS)

Sarker, M.S.H.; Ibrahim, M. Nordin; Ab. Aziz, N.; Mohd. Salleh, P.

2014-01-01

Highlights: • We presented performance evaluation approach for industrial inclined bed paddy dryer. • Specific electrical energy consumption was 1.44–1.95 MJ/kg water evaporated. • Specific thermal energy consumption was 2.77–3.47 MJ/kg water evaporated. • Dryer yielded 1–4% higher head rice at drying temperature of 38–39 °C than 41–42 °C. • Dryers should be operated at 38–39 °C for 1–4% higher head rice at reasonable energy. - Abstract: The performance evaluation of any industrial dryer regarding energy consumption and product quality should be assessed to check its present status and to suggest for further efficient operation. An investigation was carried out to evaluate the impact of drying temperature and air flow on energy consumption and quality of rice during paddy drying with industrial inclined bed dryer (IBD) with average holding capacity of 15 ton in the selected complexes of Padiberas Nasional Berhad (BERNAS)-the national paddy custodian of Malaysia. In reducing paddy moisture content (mc) from 22% to 23% wet basis (wb) down to around 12.5% wb, the final mc, the specific electrical (in terms of primary energy) and the specific thermal energy consumption were found to be varied between 1.44 to 1.95 MJ/kg water evaporated and 2.77 to 3.47 MJ/kg water evaporated, respectively. Analysis revealed that the specific electrical energy consumption was around 20% lesser and the specific thermal energy consumption of IBDs was around 10% higher during drying with air temperature of 41–42 °C than drying with 38–39 °C in reducing paddy mc from 22% to 23% (wb) down to around 12.5% (wb). However, paddy being with almost same initial mc dried using drying temperature of 38–39 °C, IBDs yielded 1–4% higher head rice yield while milling recovery and whiteness were comparable at acceptable milling degree and transparency. The bed air flows between 0.27 and 0.29 m 3 m −2 s −1 resulted in higher head rice yield slightly while its

ANFSQ-7 the computer that shaped the cold war

CERN Document Server

Ulmann, Bernd

2014-01-01

One of the most impressive computer systems ever was the vacuum tube based behemoth AN/FSQ-7, which was the heart of the ""Semi Automatic Ground Environment"". Machines of this type were children of the Cold War and had a tremendous effect not only on this episode in politics but also generated a vast amount of spin-offs which still shape our world.

Mathematical modeling of a mixed flow spray dryer

International Nuclear Information System (INIS)

Kasiri, N.; Delkhan, F.

2001-01-01

In this paper a mathematical model has been developed to simulate the behavior of spray dryers with an up-flowing spray. The model is based on mass, energy and momentum balance on a single droplet , and mass and energy balances on the drying gas. The system of nonlinear differential equations thus obtained is solved to predict the changes in temperature, humidity, diameter, velocity components and the density of the droplets as well as the temperature and the humidity changes of the drying gas. The predicted results were then compared with an industrially available set of results. A good degree of proximity between the two is reported

Correlations of Mean Process Parameters for Agricultural Products Drying in Thin Bed in Solar Direct Dryers

Directory of Open Access Journals (Sweden)

MSc. Ciro César Bergues-Ricardo

2015-11-01

Full Text Available A group of correlations is given between mean parameters of drying process drying velocity, energy losses, useful energy, and thermal efficiency. Those are suitable for conditions of thin bed drying, in direct solar dryers, and may help for developing of an integral approach of solar drying in those conditions. Correlations are reliable for drying processes of diverse crop products specified, suchas roots, seeds, vegetables, fruits, wood, etc, with natural or forced convection. Correlations were validated in Cuba for usual ranges of efficiency and products in solar dryers of cover, cabinet and house types, in tropical conditions. These correlations are useful for design and exploitation ofdryers and for theoretical and practical comprehension of solar drying like a system.

Final report on the Controlled Cold Helium Spill Test in the LHC tunnel at CERN

CERN Document Server

Dufay-Chanat, L; Casas-Cubillos, J; Chorowski, M; Grabowski, M; Jedrusyna, A; Lindell, G; Nonis, M; Koettig, T; Vauthier, N; van Weelderen, R; Winkler, T

2015-01-01

The 27 km circumference LHC underground tunnel is a space in which the helium cooled LHC magnets are installed. The vacuum enclosures of the superconducting magnets are protected by over-pressure safety relief devices that open whenever cold helium escapes either from the magnet cold enclosure or from the helium supply headers, into this vacuum enclosure. A 3-m long no stay zone around these devices is defined based on scale model studies, protecting the personnel against cold burns or asphyxia caused by such a helium release event. Recently, several simulation studies have been carried out modelling the propagation of the helium/air mixture, resulting from the opening of such a safety device, along the tunnel. The released helium flows vary in the range between 1 kg/s and 0.1 kg/s. To validate these different simulation studies, real life mock-up tests have been performed inside the LHC tunnel, releasing helium flow rates of 1 kg/s, 0.3 kg/s and 0.1 kg/s. For each test, up to 1000 liters of liquid helium wer...

Ultrasonic monitoring of Iberian fat crystallization during cold storage

International Nuclear Information System (INIS)

Corona, E; García-Pérez, J V; Santacatalina, J V; Peña, R; Benedito, J

2012-01-01

The aim of this work was to evaluate the use of ultrasonic measurements to characterize the crystallization process and to assess the textural changes of Iberian fat and Iberian ham during cold storage. The ultrasonic velocity was measured in two types of Iberian fats (Montanera and Cebo) during cold storage (0, 2, 5, 7 and 10 °C) and in vacuum packaged Iberian ham stored at 6°C for 120 days. The fatty acid profile, thermal behaviour and textural properties of fat were determined. The ultrasonic velocity and textural measurements showed a two step increase during cold storage, which was related with the separate crystallization of two fractions of triglycerides. It was observed that the harder the fat, the higher the ultrasonic velocity. Likewise, Cebo fat resulted harder than Montanera due to a higher content of saturated triglycerides. The ultrasonic velocity in Iberian ham showed an average increase of 55 m/s after 120 days of cold storage due to fat crystallization. Thus, non-destructive ultrasonic technique could be a reliable method to follow the crystallization of fats and to monitor the changes in the textural properties of Iberian ham during cold storage.

Experimental investigation of a solar dryer with natural convective heat flow

Energy Technology Data Exchange (ETDEWEB)

Gbaha, P.; Yobouet Andoh, H.; Kouassi Saraka, J. [Laboratoire d' Energies d' Energies Nouvelles et Renouvelables, Institut National Polytechnique Felix Houphoeuet-Boigny, B.P. 1526 Yamoussoukro (Ivory Coast); Kamenan Koua, B.; Toure, S. [Laboratoire d' Energie Solaire, Universite de Cocody, 22 B.P.: 582, Abidjan 22 (Ivory Coast)

2007-09-15

A direct type natural convection solar dryer is designed. It is constructed in local materials (wood, blades of glass, metals) then tested experimentally in foodstuffs drying (cassava, bananas, mango). It is about an experimental approach which consists in analyzing the behavior of the dryer. The study relates mainly kinetics and establishment of drying heat balances. The influence of significant parameters governing heat and mass transfers, such as solar incident radiation, drying air mass flow and effectiveness, is analyzed in order to evaluate its thermal performances. Experimental data can be represented by empirical correlations of the form M(t)=M{sub i}exp(-kt) for representation of drying process. The resolution of these drying equations makes-possible to predict total drying time of each product. Moreover, this drying process allows to reduce the moisture content of cassava and sweet banana approximately to 80% in 19 and 22 h, respectively to reach the safety threshold value of 13%. This value permits the conservation of these products about one year without deterioration. The determination of parameters, like ambient temperature, drying chamber temperature, drying air mass flow and incident heat fluxes, allow to predict the drying effectiveness for modeling and refining the dimensioning of the elaborate prototype. (author)

Effect of separation and drainage of condensate on dehumidification in a refrigerated dryer; Reito joshitsuki ni okeru gyoshukusui bunri/haishutsu noryoku no joshitsu seino ni oyobosu eikyo

Energy Technology Data Exchange (ETDEWEB)

Goto, H.; Ichinose, T. [SMC Corp., Tokyo (Japan); Tanzawa, Y.; Hashizume, T. [Waseda Univ., Tokyo (Japan). Science and Engineering Research Lab.

1995-11-15

The representative refrigerated dryer as the compressed air dryers is one in which air was cooled at rather low temperature by working medium of refrigerators, and the dew point was decreased with increase of pressure, and air with low relative humility called as the dried air was obtained again by heating. In this paper, for clarifying effect of separation and drainage of condensate on dehumidification in a refrigerated dryer in relation to shape of a main cooler and a precool-reheater and air temperature of each part, calculation and experimental investigation were conducted. In a refrigerated dryer, condensate happened in the precool part of a precool-reheater and a main cooler, and this would give rise to reduce of separation and drainage of condensate and increase of thermal loads of each heat exchange, and would made dehumidification low. For a fact that decrease of separation and drainage of condensate in a main cooler would bring out heat conduction with phase change in the reheating part of a precool-reheater, it has a profitable side, but it is not desirable for ability of dryers. 6 refs., 9 figs., 1 tab.

78 FR 20842 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2013-04-08

... DeLonghi); energy and environmental advocates (American Council for an Energy Efficient Economy (ACEEE... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket Number EERE-2013-BT-STD-0020] RIN 1904-AC98 Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and Room Air Conditioners...

Preservation of fruits and vegetables using solar dryers. A comparative study for solar and natural drying of grapes, figs, tomatoes and onions. IV. temperature measurements, calculating the generated energy and dryer efficiency during drying

International Nuclear Information System (INIS)

Sehery, A.A.; Gallali, Y.M.; Shoshan, H.

2000-01-01

This study has taken four axis, first, design and construction of the dryer, secondly, microbial load determination, thirdly, chemical and sensory evaluation data. The results of these three parts were published earlier at the International Congress on Application of Solar and Renewable Energy, Food Science and Technology and World Renewable Energy Congress V, Cairo, Egypt, 1992, 1996 and Florence, Italy, 1998, respectively. The whole study was oriented towards comparing the solar (three modes, direct, indirect, and mixed) and natural drying. The fourth part of the study is dealing with some parameters affecting drying as temperature measurement, calculating the generated energy and the dryer efficiency during drying periods. Drying temperature is considered the most important factor in the drying operation, since the accuracy of temperature measurement gives the correct results and right indication for the approval of these scientific methods in the drying operation and the design of solar dryers. In this project, we depended on temperature measurements at different points by means of thermocouples fixed in the heat collector and the drying chamber. The average temperature outside the dryer ranged from 21-41 degree C. That of the heat collector were 40-75 degree C and those of the drying chamber were in the range of 40-73 degree C. The radiation measurements calculated depending on the results recorded by the solar center instruments from 5/8/95 - 16/10/95. The thermal energy existing from the heat collector to the drying chamber during the drying period was measured using the equation of Holland. From the investigation results, we can conclude that in all trials, solar drying was a more efficient method for drying all samples of fruits and vegetables, especially for grapes, figs and onion. Grapes dried using mixed mode from 83 % to 30 % moisture in 4 days at an average temperature of 55 degree C while natural drying reduced the moisture to 57% for the same period

Modelling and simulation of processes by smart sensing : a solar dryer for plant material

Energy Technology Data Exchange (ETDEWEB)

Correa, E.C.; Diezma, B.; Ruiz-Altisent, M. [LPF-TAGRALIA Univ. Politecnica, CENIM-CSIC, Madrid (Spain)

2010-07-01

This paper reported on a study in which as small wood dryer was modelled. Studies have shown that properly designed solar dryers may prove to be energy saving devices for drying processes. The drying rate expressed as -dX/dt=f/X (where X is DB wood moisture content), allows to identify 2 different kinetics, notably for high X values or fibre saturation point (FSP) and for X values under FSP, in which diffusion is the mechanism that governs a decreasing drying rate at this stage. The complex drying rate model developed in this study made it possible the determine the wood and convective mass transfer at the wood-air interface. Validation and application to fruit and plant drying cycles is currently underway. Three different proposed models are used in the software for a smart sensor system, which is based on Sensirion sensors for temperature and relative humidity in the air, and thermocouples for timber temperature.

Emission of muonic hydrogen isotopes from solid hydrogen layers into vacuum

International Nuclear Information System (INIS)

Marshall, G.M.; Bailey, J.M.; Beer, G.A.

1989-10-01

An attempt was made to create in vacuum free muonic hydrogen atoms, muonic protium and muonic deuterium. The method was based on slowing a beam of μ - in a layer of solid hydrogen in vacuum frozen to a cold gold foil substrate. Muonic hydrogen formed near the surface is emitted from it into the vacuum with an energy spectrum determined by the formation and subsequent scattering processes. For a typical total cross section of 10 -19 cm 2 the interaction probability is 0.43 μm -1 . For emission at an energy of order 1 eV, the muonic atom travels about 10 mm in vacuum prior to decay. No corresponding signal was observed with a deuterium layer of 6 mg/cm 2 . The natural abundance of deuterons in hydrogen leads to transfer of the muon in a mean time of about 500 ns, and because of the reduced mass difference, the m u - d obtains a kinetic energy of 45 eV, from which the atom will scatter and slow until the energy of the Ramsauer-Townsend minimum is reached and the hydrogen film becomes nearly transparent to μ - d. The Ramsauer-Townsend effect is also expected to show up for tritium in protium, which means a source of μ - t in vacuum should be possible

Alterations in fruit and vegetable beta-carotene and vitamin C content caused by open-sun drying, visqueen-covered and polyethylene-covered solar-dryers.

Science.gov (United States)

Ndawula, J; Kabasa, J D; Byaruhanga, Y B

2004-08-01

This study investigated the effects of three drying methods (open sun drying, visqueen-covered solar dryer and polyethylene-covered solar dryer) on b-carotene and vitamin C content of edible portions of mango fruit (Mangifera indica) and cowpea leaves (Vigna unguiculata). Commercial samples were analysed for vitamin C by titrimetry and b-carotene by spectrophotometry at 450 nm. Differences in vitamin retention and loss associated with the three drying methods were assessed by analysis of variance and least significant difference (LSD) at (pdrying. Open sun drying method caused the greatest b-carotene and vitamin C loss (58% and 84% respectively), while the visqueen-covered solar dryer caused the least loss (34.5% and 71% respectively). Blanching cowpea leaves improved b-carotene and vitamin C retention by 15% and 7.5% respectively. The b-carotene and vitamin C content of fresh ripe mango fruit was 5.9 and 164.3 mg/100g DM respectively. Similar to effects on cowpea leaves, the mango micronutrient content decreased (pdrying. The open sun drying method caused the greatest b-carotene (94.2%) and vitamin C (84.5%) loss, while the visqueen-covered solar dryer caused the least (73 and 53% respectively). These results show that the three solar drying methods cause significant loss of pro-vitamin A and vitamin C in dried fruits and vegetables. However, open sun drying causes the most loss and the visqueen-covered solar dryer the least, making the later a probable better drying technology for fruit and vegetable preservation. The drying technologies should be improved to enhance vitamin retention.

Vacuum system of the compact Energy Recovery Linac

Energy Technology Data Exchange (ETDEWEB)

Honda, T., E-mail: tohru.honda@kek.jp; Tanimoto, Y.; Nogami, T.; Takai, R.; Obina, T.; Asaoka, S.; Uchiyama, T.; Nakamura, N. [High Energy Accelerator Research Organization (KEK) (1-1 Oho, Tsukuba, Ibaraki 305-0801, Japan) (Japan)

2016-07-27

The compact Energy Recovery Linac (cERL), a test accelerator to establish important technologies demanded for future ERL-based light sources, was constructed in late 2013 at KEK. The accelerator was successfully commissioned in early 2014, and demonstrated beam circulation with energy recovery. In the cERL vacuum system, low-impedance vacuum components are required to circulate high-intensity, low-emittance and short-bunch electron beams. We therefore developed ultra-high-vacuum (UHV)-compatible flanges that can connect beam tubes seamlessly, and employed retractable beam monitors, namely, a movable Faraday cup and screen monitors. In most parts of the accelerator, pressures below 1×10{sup −7} Pa are required to mitigate beam-gas interactions. Particularly, near the photocathode electron gun and the superconducting (SC) cavities, pressures below 1×10{sup −8} Pa are required. The beam tubes in the sections adjoining the SC cavities were coated with non-evaporable getter (NEG) materials, to reduce gas condensation on the cryo-surfaces. During the accelerator commissioning, stray magnetic fields from the permanent magnets of some cold cathode gauges (CCGs) were identified as a source of the disturbance to the beam orbit. Magnetic shielding was specially designed as a remedy for this issue.

Survey on solar dryers for drying of food and wood in Ghana

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S.; Correll Frank, F. [Danish Technological Inst., Taastrup (Denmark); Floejgaard Kristensen, E. [Danish Inst. of Agricultural Sciences, Tjele (Denmark)

1999-11-01

The survey was conducted as a part of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat'. The aim of the survey was to investigate the need for drying of food and wood in Ghana and the already existing experience on solar drying in order to form a basis for the initial decisions within the project concerning the location of three demonstration solar dryers for crops, fish and wood, which species to dry and the type of solar dryers. The project deals with transfer of knowledge in the field of drying of crops and wood and solar air heating systems from Denmark to Ghana. The aim of the survey was, therefore, also to give the Danish experts an impression of the conditions in Ghana in order to facilitate an appropriate design of the solar dryers. Three of the four Danish partners participated in the survey. The fourth Danish partner - the manufacturer of solar heating systems Aidt Miljoe - are already familiar with the conditions in Ghana due to an earlier project in Ghana. The survey was planed by the Energy Commission of Ghana, the Ghanaian partner and consultants: DENG, University of Science and Technology, Kumasi and Econkoad. The time schedules for the survey - one for crops/fish and one for wood - are found in Annex A. The schedules were very well prepared and the sites to visit were well chosen. The visits gave the Danish experts a good overview of the situation in Ghana in the field of post harvesting of crops, handling of fish, drying and manufacturing of wood and existing experience on solar drying. The schedules included a large variety of different information and impressions e.g. ranging from large sawmill to small carpenters and workshops. Despite tight schedules the consultants managed to stick very close to the time schedules shown in Annex A. (au)

Simulation of exhaust gas heat recovery from a spray dryer

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

This study explored various alternatives in improving the energy utilization of spray drying process through the exhaust gas heat recovery. Extensible and user-friendly simulation code was written in Visual Basic for Applications within Microsoft Excel for this purpose. The effects of process parameters were analyzed on the energy efficiency and energy saving in the industrial-scale spray drying system with exhaust gas heat recovery in an air-to-air heat exchanger and in the system with partial recirculation of exhaust air. The spray dryer is equipped with an indirect heater for heating the drying air. The maximum gains of 16% in energy efficiency and 50% in energy saving were obtained for spray drying system equipped with heat exchanger for exhaust air heat recovery. In addition, 34% in energy efficiency and 61% in energy saving for system with recirculation of exhaust air in the present range of process parameters. The high energy efficiency was obtained during drying of large amount of dilute slurry. The energy saving was increased using the large amount of hot drying air. - Highlights: • We model industrial-scale spray drying process with the exhaust gas heat recovery. • We develop an Excel VBA computer program to simulate spray dryer with heat recovery. • We examine effects of process parameters on energy efficiency and energy saving. • High energy efficiency is obtained during drying of large amount of dilute slurry. • Energy saving is increased using the large amount of hot drying air

The effect of fan speed control system on the inlet air temperature uniformity in a solar dryer

Directory of Open Access Journals (Sweden)

S. F Mousavi

2015-09-01

Full Text Available Introduction: Drying process of agricultural products, fruits and vegetables are highly energy demanding and hence are the most expensive postharvest operation. Nowadays, the application of control systems in different area of science and engineering plays a key role and is considered as the important and inseparable parts of any industrial process. The review of literature indicates that enormous efforts have been donefor the intelligent control of solar driers and in this regard some simulation models are used through computer programming. However, because of the effect of air velocity on the inlet air temperature in dryers, efforts have been made to control the fan speed based ont he temperature of the absorber plate in this study, and the behavior of this system was compared with an ordinary dryer without such a control system. Materials and methods: In this study, acabinet type solar dryer with forced convection and 5kg capacity of fresh herbs was used. The dryer was equipped with a fan in the outlet chamber (the chimney for creating air flow through the dryer. For the purpose of research methods and automatic control of fan speed and for adjusting the temperature of the drying inlet air, a control system consisting of a series of temperature and humidity sensors and a microcontroller was designed. To evaluatethe effect of the system with fan speed control on the uniformity of air temperature in the drying chamber and hence the trend of drying process in the solar dryer, the dryer has been used with two different modes: with and without the control of fan speed, each in twodays (to minimize the errors of almost the same ambient temperature. The ambient air temperature during the four days of experiments was obtained from the regional Meteorological Office. Some fresh mint plants (Mentha longifolia directly harvested from the farm in the morning of the experiment days were used as the drying materials. Each experimental run continued for 9

Influence of cold deformation on martensite transformation and mechanical properties of Ti-Nb-Ta-Zr alloy

International Nuclear Information System (INIS)

Wang Liqiang; Lu Weijie; Qin Jining; Zhang Fan; Zhang Di

2009-01-01

Ti-35Nb-2Ta-3Zr alloy was fabricated by vacuum consumable arc melting furnace and hot pressing. Microstructure and phase transformation of solution-treated (ST) and cold-rolled (CR) plates of Ti-Nb-Ta-Zr alloy were observed. Different microstructure of strain-induced martensite transformation during cold deformation were investigated. With the increase of reduction of cold rolling, microstructure of α''-phase changed from acicular martensite to butterfly shaped martensite and showed variant crossed and cross-hatched when the reduction of cold rolling was over 60%. Mechanical properties and SEM images of the fracture surface indicated that the alloy fabricated by cold deformation showed favorable strength and plasticity. Owing to the excellent cold workability and biomedical safety of elements of Nb, Ta and Zr, Ti-Nb-Ta-Zr alloy contributed much to medical applications

Analysis of Energy Consumption of "Compression Heat" Pressure Heat Dryer%“压缩热”干燥机能耗分析

Institute of Scientific and Technical Information of China (English)

李申

2015-01-01

作为典型的热质交换设备，吸附干燥器再生能量是被吸水量锁定的。总耗能受到吸附剂本身物理性质的制约，可用“质量守恒”与“能量守恒”两大定律来解释其能耗过程。各类吸附干燥器能耗量都要通过“能量衡算”来确定。“压缩热”干燥器与其他一切加热干燥器一样采取了“长周期”工作循环制，解吸环节无效热损很大。无热再生干燥器则采用了“短周期”工作制，为实际耗气量减少留有了较大的空间。%As the typical heat and mass transfer equipment, the energy of regenerative desiccant dryers is limited by water absorption. The total energy consumption is restricted by the physical properties of the adsorbent, which can be explained through two laws of conservation of mass and energy conservation. The energy consumption in each absorption dryers should be determined by“energy balance”.“Compression heat”dryer adopts“long-period”working cycle system as other heating dryers, in which invalid heat losses are great in desorption process. However, regenerated dryer without heat adopts“short-period”working cycle system, which provides greater space for actual gas consumption reduction.

Thermo-mechanical Design Methodology for ITER Cryodistribution cold boxes

Science.gov (United States)

Shukla, Vinit; Patel, Pratik; Das, Jotirmoy; Vaghela, Hitensinh; Bhattacharya, Ritendra; Shah, Nitin; Choukekar, Ketan; Chang, Hyun-Sik; Sarkar, Biswanath

2017-04-01

The ITER cryo-distribution (CD) system is in charge of proper distribution of the cryogen at required mass flow rate, pressure and temperature level to the users; namely the superconducting (SC) magnets and cryopumps (CPs). The CD system is also capable to use the magnet structures as a thermal buffer in order to operate the cryo-plant as much as possible at a steady state condition. A typical CD cold box is equipped with mainly liquid helium (LHe) bath, heat exchangers (HX’s), cryogenic valves, filter, heaters, cold circulator, cold compressor and process piping. The various load combinations which are likely to occur during the life cycle of the CD cold boxes are imposed on the representative model and impacts on the system are analyzed. This study shows that break of insulation vacuum during nominal operation (NO) along with seismic event (Seismic Level-2) is the most stringent load combination having maximum stress of 224 MPa. However, NO+SMHV (Séismes Maximaux Historiquement Vraisemblables = Maximum Historically Probable Earthquakes) load combination is having the least safety margin and will lead the basis of the design of the CD system and its sub components. This paper presents and compares the results of different load combinations which are likely to occur on a typical CD cold box.

Cold Test and Performance Evaluation of Prototype Cryoline-X

Science.gov (United States)

Shah, N.; Choukekar, K.; Kapoor, H.; Muralidhara, S.; Garg, A.; Kumar, U.; Jadon, M.; Dash, B.; Bhattachrya, R.; Badgujar, S.; Billot, V.; Bravais, P.; Cadeau, P.

2017-12-01

The multi-process pipe vacuum jacketed cryolines for the ITER project are probably world’s most complex cryolines in terms of layout, load cases, quality, safety and regulatory requirements. As a risk mitigation plan, design, manufacturing and testing of prototype cryoline (PTCL) was planned before the approval of final design of ITER cryolines. The 29 meter long PTCL consist of 6 process pipes encased by thermal shield inside Outer Vacuum Jacket of DN 600 size and carries cold helium at 4.5 K and 80 K. The global heat load limit was defined as 1.2 W/m at 4.5 K and 4.5 W/m at 80 K. The PTCL-X (PTCL for Group-X cryolines) was specified in detail by ITER-India and designed as well as manufactured by Air Liquide. PTCL-X was installed and tested at cryogenic temperature at ITER-India Cryogenic Laboratory in 2016. The heat load at 4.5 K and 80 K, estimated using enthalpy difference method, was found to be approximately 0.8 W/m at 4.5 K, 4.2 W/m at 80 K, which is well within the defined limits. Thermal shield temperature profile was also found to be satisfactory. Paper summarizes the cold test results of PTCL-X

Leybold vacuum handbook

CERN Document Server

Diels, K; Diels, Kurt

1966-01-01

Leybold Vacuum Handbook presents a collection of data sets that are essential for numerical calculation of vacuum plants and vacuum processes. The title first covers vacuum physics, which includes gas kinetics, flow phenomena, vacuum gauges, and vapor removal. Next, the selection presents data on vacuum, high vacuum process technology, and gas desorption and gettering. The text also deals with materials, vapor pressure, boiling and melting points, and gas permeability. The book will be of great interest to engineers and technicians that deals with vacuum related technologies.

Vacuum Technology

Energy Technology Data Exchange (ETDEWEB)

Biltoft, P J

2004-10-15

The environmental condition called vacuum is created any time the pressure of a gas is reduced compared to atmospheric pressure. On earth we typically create a vacuum by connecting a pump capable of moving gas to a relatively leak free vessel. Through operation of the gas pump the number of gas molecules per unit volume is decreased within the vessel. As soon as one creates a vacuum natural forces (in this case entropy) work to restore equilibrium pressure; the practical effect of this is that gas molecules attempt to enter the evacuated space by any means possible. It is useful to think of vacuum in terms of a gas at a pressure below atmospheric pressure. In even the best vacuum vessels ever created there are approximately 3,500,000 molecules of gas per cubic meter of volume remaining inside the vessel. The lowest pressure environment known is in interstellar space where there are approximately four molecules of gas per cubic meter. Researchers are currently developing vacuum technology components (pumps, gauges, valves, etc.) using micro electro mechanical systems (MEMS) technology. Miniature vacuum components and systems will open the possibility for significant savings in energy cost and will open the doors to advances in electronics, manufacturing and semiconductor fabrication. In conclusion, an understanding of the basic principles of vacuum technology as presented in this summary is essential for the successful execution of all projects that involve vacuum technology. Using the principles described above, a practitioner of vacuum technology can design a vacuum system that will achieve the project requirements.

Modelling the drying kinetics of green peas in a solar dryer and under open sun

Energy Technology Data Exchange (ETDEWEB)

Sunil [Department of Mechanical Engineering, BRCM CET Bahal, Haryana–127028 (India); Varun [Department of Mechanical Engineering, NIT Hamirpur, (H.P.)–177005 (India); Sharma, Naveen [Department of Mechanical and Industrial Engineering, IITR, (U.K.)–247667 (India)

2013-07-01

The drying kinetics of green peas was investigated in an indirect solar dryer and under open sun. The entire drying process took place exclusively in falling rate period. The constant rate period was absent from the drying curves. The rehydration capacity was also determined for peas dried in solar dryer and under open sun. The rehydration capacity of solar dried peas was found higher than open sun dried peas. The drying data obtained from experiments were fitted to eight different mathematical models. The performance of these models was examined by comparing the coefficient of correlation (R2), sum of squares error (SSE), mean squared error (MSE) and root mean square error (RMSE) between observed and predicted values of moisture ratios. Among these models, the thin layer drying model developed by Page showed good agreement with the data obtained from experiments for bottom tray. The Midilli et al. model has shown better fit to the experimental data for top tray and open sun than other models.

Indian Vacuum Society: The Indian Vacuum Society

Science.gov (United States)

Saha, T. K.

2008-03-01

The Indian Vacuum Society (IVS) was established in 1970. It has over 800 members including many from Industry and R & D Institutions spread throughout India. The society has an active chapter at Kolkata. The society was formed with the main aim to promote, encourage and develop the growth of Vacuum Science, Techniques and Applications in India. In order to achieve this aim it has conducted a number of short term courses at graduate and technician levels on vacuum science and technology on topics ranging from low vacuum to ultrahigh vacuum So far it has conducted 39 such courses at different parts of the country and imparted training to more than 1200 persons in the field. Some of these courses were in-plant training courses conducted on the premises of the establishment and designed to take care of the special needs of the establishment. IVS also regularly conducts national and international seminars and symposia on vacuum science and technology with special emphasis on some theme related to applications of vacuum. A large number of delegates from all over India take part in the deliberations of such seminars and symposia and present their work. IVS also arranges technical visits to different industries and research institutes. The society also helped in the UNESCO sponsored post-graduate level courses in vacuum science, technology and applications conducted by Mumbai University. The society has also designed a certificate and diploma course for graduate level students studying vacuum science and technology and has submitted a syllabus to the academic council of the University of Mumbai for their approval, we hope that some colleges affiliated to the university will start this course from the coming academic year. IVS extended its support in standardizing many of the vacuum instruments and played a vital role in helping to set up a Regional Testing Centre along with BARC. As part of the development of vacuum education, the society arranges the participation of

Analysis of heat recovery from a spray dryer by recirculation of exhaust air

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

Highlights: • We study a spray dryer with heat recovery by partial recirculation of exhaust air. • We examine effects of process parameters on energy efficiency and energy savings. • Decreasing drying air temperature and flow rate will increase energy efficiency. • Increasing recirculation ratio and slurry feed rate will increase energy efficiency. - Abstract: Model simulations were employed to investigate the influences of process parameters on the energy recovery in spray drying process that partially recycle the exhaust drying gas. The energy efficiency and energy saving were studied for various values of recirculation ratios with respect to the temperature and flow rate of the drying air, slurry feed rate and concentration of slurry in spray drying of advanced ceramic materials. As a result, significant gains in energy efficiency and energy saving were obtained for a spray drying system with high recirculation ratio of exhaust air. The high slurry feed rate and the low slurry concentration, inlet drying air temperature and drying air flow rate enhanced the energy efficiency of spray drying system. However, the high energy saving was obtained in spray dryers operating at low slurry feed rate and high slurry concentration

Parton fragmentation in the vacuum and in the medium

CERN Document Server

Albino, S.; Arleo, F.; Besson, Dave Z.; Brooks, William K.; Buschbeck, B.; Cacciari, M.; Christova, E.; Corcella, G.; D'Enterria, David G.; Dolejsi, Jiri; Domdey, S.; Estienne, M.; Hamacher, Klaus; Heinz, M.; Hicks, K.; Kettler, D.; Kumano, S.; Moch, S.O.; Muccifora, V.; Pacetti, S.; Perez-Ramos, R.; Pirner, H.J.; Pronko, Alexandre Pavlovich; Radici, M.; Rak, J.; Roland, C.; Rudolph, Gerald; Rurikova, Z.; Salgado, C.A.; Sapeta, S.; Saxon, David H.; Seidl, Ralf-Christian; Seuster, R.; Stratmann, M.; Tannenbaum, Michael J.; Tasevsky, M.; Trainor, T.; Traynor, D.; Werlen, M.; Zhou, C.

2008-01-01

We present the mini-proceedings of the workshop on ``Parton fragmentation in the vacuum and in the medium'' held at the European Centre for Theoretical Studies in Nuclear Physics and Related Areas (ECT*, Trento) in February 2008. The workshop gathered both theorists and experimentalists to discuss the current status of investigations of quark and gluon fragmentation into hadrons at different accelerator facilities (LEP, B-factories, JLab, HERA, RHIC, and Tevatron) as well as preparations for extension of these studies at the LHC. The main physics topics covered were: (i) light-quark and gluon fragmentation in the vacuum including theoretical (global fits analyses and MLLA) and experimental (data from e+e-, p-p, e-p collisions) aspects, (ii) strange and heavy-quark fragmentation, (iii) parton fragmentation in cold QCD matter (nuclear DIS), and (iv) medium-modified fragmentation in hot and dense QCD matter (high-energy nucleus-nucleus collisions). These mini-proceedings consist of an introduction and short summ...

A Compact, High-Flux Cold Atom Beam Source

Science.gov (United States)

Kellogg, James R.; Kohel, James M.; Thompson, Robert J.; Aveline, David C.; Yu, Nan; Schlippert, Dennis

2012-01-01

The performance of cold atom experiments relying on three-dimensional magneto-optical trap techniques can be greatly enhanced by employing a highflux cold atom beam to obtain high atom loading rates while maintaining low background pressures in the UHV MOT (ultra-high vacuum magneto-optical trap) regions. Several techniques exist for generating slow beams of cold atoms. However, one of the technically simplest approaches is a two-dimensional (2D) MOT. Such an atom source typically employs at least two orthogonal trapping beams, plus an additional longitudinal "push" beam to yield maximum atomic flux. A 2D atom source was created with angled trapping collimators that not only traps atoms in two orthogonal directions, but also provides a longitudinal pushing component that eliminates the need for an additional push beam. This development reduces the overall package size, which in turn, makes the 2D trap simpler, and requires less total optical power. The atom source is more compact than a previously published effort, and has greater than an order of magnitude improved loading performance.

Is it safe to disturb the vacuum

International Nuclear Information System (INIS)

Hut, P.

1984-01-01

Ultra-relativistic U 238 -U 238 collisions, which are now being envisioned for the next generation of heavy ion accelerators, do not occur in large quantities anywhere in the universe at present. Nor have they ever occurred abundantly in the past. When U 238 nuclei were first synthesized the universe had grown already for too cold. This raises the question whether such a novel type of experiment could trigger a catastrophic phase transition of the vacuum to a lower energy state, a possibility naturally occurring in many spontaneously broken quantum field theories. Theoretical calculations of the collisionally induced nucleation rate of critical bubbles precipitating such phase transitions are not yet available, and nothing is known about the parameters describing the barrier separating our vacuum from a possibly lower energy state. Fortunately, available cosmic ray evidence suggests that sporadic individual U 238 -U 238 collisions have indeed occurred at ultra-relativistic energies inside our past light cone, which would imply that the proposed experiments do not tread potentially dangerous new ground. Direct confirmation of the predicted small abundance of U 238 and other actinides in cosmic rays at energies in the interesting range 10 13 -10 15 eV, corresponding to 40 GeV/n-4 TeV/n, is not feasible at present. Nevertheless, even indirect detection of at least some ultra-heavy nuclei in the actinide group (Z>88) in this energy range would more affirmatively answer the question: 'Do we dare disturb the vacuum. (orig.)

Influence of the process control on the thermal energy requirement of convection dryers in the brick industry; Einfluss der Prozessfuehrung auf den thermischen Energiebedarf von Konvektionstrocknern in der Ziegelindustrie

Energy Technology Data Exchange (ETDEWEB)

Tretau, Anne

2008-06-10

Brick manufacturing demands high amount of energy. The energy flow analysis inside the brick factory shows that the convective drying of green bricks consumes more than half of the total thermal energy required for brick manufacturing. Therefore this paper deals with the theoretical analysis and investigation for the energy requirement of green bricks. For this, a physical-based model has been developed, which describes the dependence of drying-kinetics as well as the energy-requirement interims of the process parameter like mass of the supply air. It turns out that the specific energy requirement substantially depends on temperature and humidity of the ambience air and also supply air mass flow and its temperature. Due to the continuous temperature rise of the green bricks during the second drying section the specific energy requirement increases significantly with the progressive motion of the drying in a chamber dryer. This is due to the fact that the green brick as well as the air conditioning distance more and more from the cooling limit. Just a low part of the dryer exhaust air is saturated. The exhaust air is continuously sucked out and the green bricks are pulled inside the dryer. So the exhaust air has a relatively higher water saturation. On general, continuous dryers have a lower energy requirement than chamber dryer. For the both types of dryers, the mathematical model shows that the increasing of the supply air temperature combined with a commensurate subsidence of supply air mass flow, results in a reduction of drying energy requirement. The change of other essential parameters of drying like green brick thickness, and density as well as the moisture diffusion coefficient, and the vapour diffusity which are only important in the second drying section are of comparatively negligible effect. The developed mathematical model is successfully implemented for the energy investigation in the industrial dryers. The increase in supply air temperature results

The progress of test and study for steam dryer in vertical steam generator

International Nuclear Information System (INIS)

Ding Xunshen

1993-01-01

Constructions, tests and test results are reviewed for three types of steam generator dryer that are concentric vertical corrugated separator, centrifugal conic separator and chevron separator. The last type is considered as the best one in comparison, which has been applied to Qinshan 300 MW steam generator. A number of pertinent remarks to draining scheme, hydraulic loss reduction, and conduct of test are given based on experiences

Temperature and energy consumption for clothing dryer; Temperatura e consumo de energia em secadora de vestuario

Energy Technology Data Exchange (ETDEWEB)

Ribeiro, Jefferson Almeida; Magalhaes Filho, Paulo [UNESP, Guaratingueta, SP (Brazil). Faculdade de Engenharia. Dept. de Energia]. E-mail: pfilho@feg.unesp.br

2000-07-01

The cloth dehumidification is done by hot air circulation through it in dryers. The air circulation is done by a fan, run by an electrical motor, and the air temperature raise, which goes through the cloths aiming their moisture dragging, is gotten by the heat dissipation from electrical resistance. This work shows the results of an experimental modeling, examining the behavior of several kinds of cloth in a vertical suspense-type dryer, such as: polyester, cotton-spandex, flannel, blue-jeans and viscose rayon. It was analyzed the behavior of the moisture content in these cloths related to controlled-temperature-air flows, determining the needed heat to reach the required drying standards. The drying device fans were tested for the determination of their flow rate and energy consumption, establishing a flow rate versus consumption relationship. Comparative results among the various kinds of cloths are presented. (author)

Removal of SO2 and NO/sub x/ from flue gas by means of a spray dryer/electron beam combination: a feasibility study

International Nuclear Information System (INIS)

Helfritch, D.J.; Feldman, P.L.; Ray, A.B.; Morgan, J.R.; Hildreth, G.A.

1982-04-01

This study examines the feasibility of adding an electron beam between the spray dryer and the fabric filter of dry scrubber flue gas desulfurization (FGD) systems. The beam promises effective removal of nitrogen oxides (NO/sub x/) and sulfur dioxide (SO 2 ), even at higher coal-sulfur levels than usually economic for dry scrubbers. The beam excites gas molecules, promoting reactions that convert SO 2 and NO/sub x/ to acids that then react with calcium compounds and are removed by the filter. Concerns examined here are feasibility and waste disposal. The cost findings are promising for both manufacture and operation. The system uses commercially available components. The relatively low temperatures and high humidity downstream of the spray dryer favor economic beam operation. The beam removes SO 2 , so the dryer can be run for economy, not high removal. The beam's incidental heating effect reduces reheat cost. Safe landfilling of the nitrate-rich waste appears practical, with leachate carrying no more nitrate than natural rain and dustfall. We expect natural pozzolanic reactions between alumina-silica compounds in the fly ash and lime compounds from the spray dryer to form an impermeable concrete-like material within 10 days after landfilling. Dry scrubber with electron beam appears competitive with commercial FGD systems, and we recommend a pilot scale operation

Experimental investigation on energy and exergy analysis of coriander (Coriadrum sativum L.) leaves drying in natural convection solar dryer

International Nuclear Information System (INIS)

Panwar, N.L.

2014-01-01

This study deals with thin layer drying characteristics of Coriandrum sativum L. leaves in a natural convection solar dryer. The Coriandrum sativum L. leaves were dried from a moisture content of 88% (w.b.) to 4.5% (w.b.) in 7.5 hours. The obtained drying data were fitted to eight different drying kinetics models. Of these, the model suggested by Midilli et al. [20] had the best fit with the drying behavior of Coriandrum sativum L. leaves. In addition, the thermodynamic behaviour of a solar dryer was evaluated. The energy efficiency during the study varied from 7.81 to 37.93%. The exergy efficiency of the drying process ranged between 55.35 and 79.39%. (author)

Design of mixed-mode natural convection solar crop dryers: Application of principles and rules of thumb

Energy Technology Data Exchange (ETDEWEB)

Forson, F.K.; Akuffo, F.O. [Department of Mechanical Engineering, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana); Nazha, M.A.A.; Rajakaruna, H. [Department of Mechanical Engineering, De Montfort University, Queens Building, Leicester LE1 9BH (United Kingdom)

2007-11-15

A mixed-mode natural convection solar crop dryer (MNCSCD) designed and used for drying cassava and other crops in an enclosed structure is presented. A prototype of the dryer was constructed to specification and used in experimental drying tests. This paper outlines the systematic combination of the application of basic design concepts, and rules of thumb resulting from numerous and several years of experimental studies used and presents the results of calculations of the design parameters. A batch of cassava 160 kg by mass, having an initial moisture content of 67% wet basis from which 100 kg of water is required to be removed to have it dried to a desired moisture content of 17% wet basis, is used as the drying load in designing the dryer. A drying time of 30-36 h is assumed for the anticipated test location (Kumasi; 6.7 N,1.6 W) with an expected average solar irradiance of 400 W/m{sup 2} and ambient conditions of 25 C and 77.8% relative humidity. A minimum of 42.4 m{sup 2} of solar collection area, according to the design, is required for an expected drying efficiency of 12.5%. Under average ambient conditions of 28.2 C and 72.1% relative humidity with solar irradiance of 340.4 W/m{sup 2}, a drying time of 35.5 h was realised and the drying efficiency was evaluated as 12.3% when tested under full designed load signifying that the design procedure proposed is sufficiently reliable. (author)

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-10-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidising gas, (3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger, and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Operational Augmentation of Forced Circulation Type Solar Dryer System Using CFD Analysis

OpenAIRE

Atul Patel; Gaurav Patel

2014-01-01

Solar drying is basically heat and mass transfer process in which the liquid water from the surface and the vapour removed by draft. The efficiency of a solar drying system is affected by the properties of drying materials.e.g. size, shape and geometry as well as ambient conditions. In this research article, the authors have done the CFD analysis of a Forced Circulation type Solar Dryer used conventionally for dehydrating vegetables and fruits. Using CFD analysis, the limiting...

Cold-walled UHV/CVD batch reactor for the growth of Si1_x/Gex layers

DEFF Research Database (Denmark)

Thomsen, Erik Vilain; Christensen, Carsten; Andersen, C.R.

1997-01-01

A novel cold-walled, lamp-heated, ultrahigh vacuum chemical vapor deposition (UHV/CVD) batch system for the growth of SiGe layers is presented. This system combines the batch capability of the standard UHV/CVD furnace with the temperature processing available in rapid thermal processing (Rm...

Time response of protection in event of vacuum failure based on Nude ionization gauge controller

Science.gov (United States)

Gao, Hui; Wang, Qiuping; Wang, Weibin; Wu, Qinglin; Chen, Wentong; Sheng, Liusi; Zhang, Yunwu

2001-10-01

This article describes the design and application of fast-response vacuum protection sensor module, based on the Nude ionization gauge and a homemade controller named GH07X. A simulative test indicated that the controller's response time was less than 200 μs when 1 atm air rushed into the vacuum system through a pulsed valve with 0.8 mm orifice nozzle and the emitting current of the Nude gauge was 4 mA. The experiment result showed that the response time mainly depended on the gas density as well as the electron emitting current of the Nude gauge filament. Compared with the vacuum protection sensors based on sputter ion pump and cold-cathode gauge, GH07X is faster and reliable besides, GH07X can be used as an ultrahigh-vacuum slow valve interlock controller with response time of 100 ms, which is faster than other gauge controllers. The widely used field-bus interface CAN and common serial interface RS232/RS485 are embedded in GH07X controller system.

Factors associated with Listeria monocytogenes contamination of cold-smoked pork products produced in Latvia and Lithuania.

OpenAIRE

Berzins,-A; Horman,-A; Lunden,-J; Korkeala,-H

2007-01-01

A total of 312 samples of sliced, vacuum packaged, cold-smoked pork from 15 meat processing plants in Latvia and Lithuania, obtained over a 15-month period from 2003 until 2004, were analyzed for the presence of Listeria monocytogenes at the end of their shelf-life. Overall, 120 samples (38%) tested positive for L. monocytogenes. Despite the long storing period, the levels of L. monocytogenes in cold-smoked pork products were low. Manufacturing processes were studied at seven meat processing ...

Full-size solar dynamic heat receiver thermal-vacuum tests

Science.gov (United States)

Sedgwick, L. M.; Kaufmann, K. J.; Mclallin, K. L.; Kerslake, T. W.

1991-01-01

The testing of a full-size, 102 kW, solar dynamic heat receiver utilizing high-temperature thermal energy storage is described. The purpose of the test program was to quantify receiver thermodynamic performance, operating temperatures, and thermal response to changes in environmental and power module interface boundary conditions. The heat receiver was tested in a vacuum chamber with liquid nitrogen cold shrouds and an aperture cold plate to partly simulate a low-Earth-orbit environment. The cavity of the receiver was heated by an infrared quartz lamp heater with 30 independently controllable zones to allow axially and circumferentially varied flux distributions. A closed-Brayton cycle engine simulator conditioned a helium-xenon gas mixture to specific interface conditions to simulate the various operational modes of the solar dynamic power module on the Space Station Freedom. Inlet gas temperature, pressure, and flow rate were independently varied. A total of 58 simulated orbital cycles, each 94 minutes in duration, was completed during the test period.

Upgrade of RHIC Vacuum Systems for High Luminosity Operation

CERN Document Server

Hseuh Hsiao Chaun; Smart, Loralie; Todd, Robert J; Weiss, Daniel

2005-01-01

With increasing ion beam intensity during recent RHIC operations, pressure rises of several decades were observed at most room temperature sections and at a few cold sections. The pressure rises are associated with electron multi-pacting, electron stimulated desorption and beam ion induced desorption and have been one of the major intensity and luminosity limiting factors for RHIC. Improvement of the warm sections has been carried out in the last few years. Extensive in-situ bakes, additional UHV pumping, anti-grazing ridges and beam tube solenoids have been implemented. Several hundred meters of NEG coated beam pipes have been installed and activated. Vacuum monitoring and interlock were enhanced to reduce premature beam aborts. Preliminary measures, such as pumping before cool down to reduce monolayer condensates, were also taken to suppress the pressure rises in the cold sections. The effectiveness of these measures in reducing the pressure rises during machine studies and during physics runs are discussed...

Contact discontinuities in a cold collision-free two-beam plasma

Science.gov (United States)

Kirkland, K. B.; Sonnerup, B. U. O.

1982-01-01

The structure of contact discontinuities in a collision-free plasma is examined using a model of a plasma which consists of two oppositely directed cold ion beams and a background of cold massless electrons such that exact charge neutrality is maintained and that the electric field is zero. The basic equations describing self-consistent equilibria are obtained for the more general situation where a net flow across the layer takes place and where the magnetic field has two nonzero tangential components but where the electric field remains zero. These equations are then specialized to the case of no net plasma flow where one of the tangential components is zero, and four different classes of sheets are obtained, all having thickness the order of the ion inertial length. The first class is for layers separating two identical plasma and magnetic field regions, the second is for an infinite array of parallel layers producing an undulated magnetic field, the third is for layers containing trapped ions in closed orbits which separate two vacuum regions with uniform identical magnetic fields, and the fourth is for layers which reflect a single plasma beam, leaving a vacuum with a reversed and compressed tangential field on the other side.

Methods for batch fabrication of cold cathode vacuum switch tubes

Science.gov (United States)

Walker, Charles A [Albuquerque, NM; Trowbridge, Frank R [Albuquerque, NM

2011-05-10

Methods are disclosed for batch fabrication of vacuum switch tubes that reduce manufacturing costs and improve tube to tube uniformity. The disclosed methods comprise creating a stacked assembly of layers containing a plurality of adjacently spaced switch tube sub-assemblies aligned and registered through common layers. The layers include trigger electrode layer, cathode layer including a metallic support/contact with graphite cathode inserts, trigger probe sub-assembly layer, ceramic (e.g. tube body) insulator layer, and metallic anode sub-assembly layer. Braze alloy layers are incorporated into the stacked assembly of layers, and can include active metal braze alloys or direct braze alloys, to eliminate costs associated with traditional metallization of the ceramic insulator layers. The entire stacked assembly is then heated to braze/join/bond the stack-up into a cohesive body, after which individual switch tubes are singulated by methods such as sawing. The inventive methods provide for simultaneously fabricating a plurality of devices as opposed to traditional methods that rely on skilled craftsman to essentially hand build individual devices.

Behavior of a portable solar dryer for pineapple fiber Comportamento de um secador solar para fibras de abacaxi

Directory of Open Access Journals (Sweden)

Róger Moya

2012-12-01

Full Text Available In Costa Rica, there has been a growing interest to use pineapple fiber from plant, for which current processes need to be improved or new processes need to be developed, with emphasis on drying methods. This work presents the design and evaluation of the behavior of a prototype portable solar dryer in four sites of Costa Rica. The design describes the main parts of the dryer, as well as how they were constructed. The behavior was evaluated according to temperature and relative humidity inside e outside the chamber, and the influence of direct and indirect solar radiation. In order to achieve improved dryer efficiency, a dehumidifier was used to control relative humidity, and a heating system was implemented during the hours of low temperature, low solar radiation and high relative humidity. Based on drying time, final moisture content of fibers of pineapple leaves from plant, and the varying hours when fibers were put to dry, the evaluation of the dryer revealed that the best fiber-drying interval is from 6h00 to 14h00, and after that, it is convenient to inject hot air and use a dehumidifier in the dryer in order to increase its efficiency.Na Costa Rica, o interesse pelo uso da fibra proveniente da folha de abacaxizeiro. Tem almentado e essa atividade precisa de melhoramento ou implementação de novos processos para alcançar maior eficiência, principalmente na secagem da fibra. O presente trabalho apresenta o design e comportamento de uma protótipo portátil de secadora solar em 4 sites geográficos da Costa Rica. Estão descritas as principais partes do secador, bem como a metodologia de construção. O comportamento foi avaliado de acordo com a temperatura e umidade relativa interna e externa da câmara e a influencia da radiação direta e indireta. Com a finalidade de melhorar a eficiência da secadora, foi usado um desumidificador para controlar a umidade relativa e ainda um sistema de aquecimento durante as horas de baixa temperatura

Vacuum mechatronics

Science.gov (United States)

Hackwood, Susan; Belinski, Steven E.; Beni, Gerardo

1989-01-01

The discipline of vacuum mechatronics is defined as the design and development of vacuum-compatible computer-controlled mechanisms for manipulating, sensing and testing in a vacuum environment. The importance of vacuum mechatronics is growing with an increased application of vacuum in space studies and in manufacturing for material processing, medicine, microelectronics, emission studies, lyophylisation, freeze drying and packaging. The quickly developing field of vacuum mechatronics will also be the driving force for the realization of an advanced era of totally enclosed clean manufacturing cells. High technology manufacturing has increasingly demanding requirements for precision manipulation, in situ process monitoring and contamination-free environments. To remove the contamination problems associated with human workers, the tendency in many manufacturing processes is to move towards total automation. This will become a requirement in the near future for e.g., microelectronics manufacturing. Automation in ultra-clean manufacturing environments is evolving into the concept of self-contained and fully enclosed manufacturing. A Self Contained Automated Robotic Factory (SCARF) is being developed as a flexible research facility for totally enclosed manufacturing. The construction and successful operation of a SCARF will provide a novel, flexible, self-contained, clean, vacuum manufacturing environment. SCARF also requires very high reliability and intelligent control. The trends in vacuum mechatronics and some of the key research issues are reviewed.

Performance modelling of plasma microthruster nozzles in vacuum

Science.gov (United States)

Ho, Teck Seng; Charles, Christine; Boswell, Rod

2018-05-01

Computational fluid dynamics and plasma simulations of three geometrical variations of the Pocket Rocket radiofrequency plasma electrothermal microthruster are conducted, comparing pulsed plasma to steady state cold gas operation. While numerical limitations prevent plasma modelling in a vacuum environment, results may be obtained by extrapolating from plasma simulations performed in a pressurised environment, using the performance delta from cold gas simulations performed in both environments. Slip regime boundary layer effects are significant at these operating conditions. The present investigation targets a power budget of ˜10 W for applications on CubeSats. During plasma operation, the thrust force increases by ˜30% with a power efficiency of ˜30 μNW-1. These performance metrics represent instantaneous or pulsed operation and will increase over time as the discharge chamber attains thermal equilibrium with the heated propellant. Additionally, the sculpted nozzle geometry achieves plasma confinement facilitated by the formation of a plasma sheath at the nozzle throat, and fast recombination ensures a neutral exhaust plume that avoids the contamination of solar panels and interference with externally mounted instruments.

Changing MFTF vacuum environment

International Nuclear Information System (INIS)

Margolies, D.; Valby, L.

1982-01-01

The Mirror Fusion Test Facility (MFTF) vaccum vessel will be about 60m long and 10m in diameter at the widest point. The allowable operating densities range from 2 x 10 9 to 5 x 10 10 particles per cc. The maximum leak rate of 10 -6 tl/sec is dominated during operation by the deliberately injected cold gas of 250 tl/sec. This gas is pumped by over 1000 square meters of cryopanels, external sorbtion pumps and getters. The design and requirements have changed radically over the past several years, and they are still not in final form. The vacuum system design has also changed, but more slowly and less radically. This paper discusses the engineering effort necessary to meet these stringent and changing requirements. Much of the analysis of the internal systems has been carried out using a 3-D Monte Carlo computer code, which can estimate time dependent operational pressures. This code and its use will also be described

Evaluation of a fruit solar dryer; Avaliacao de um secador solar de frutas

Energy Technology Data Exchange (ETDEWEB)

Berthier, L.J.; Bittencourt, J.; Queiroz, M.R.

2000-07-01

A study of the Nanica banana drying was carried out in a solar dryer with six trays operating with direct exposure of the product to the solar radiation and internal convection. The solar drying was performed College of Agricultural Engineering of the UNICAMP, Campinas, S.Paulo state, Brazil. The study aimed a 20 to 25 per cent final humidity of the dry product, result obtained in the different trays during a maximum drying period of 147 hours (6 days), in a batch system. During the drying period, the average temperature of the environment air at daylight was of 26 degree Celsius with a maximum of 32 degree Celsius, and 18 degrees Celsius during nocturnal period, with a minimum of 12,6 degree Celsius. In the inward of the dryer reached average values near to 50 degree Celsius, measured at noon. The 29,540 kg initial net weight of peeled banana was reduced to yield of 10,815 kg after the drying process, obtaining an income of 36,61 percent of the total production. With the values of the product weight loss, the curves of the drying in each tray had been built, observing that, in the upper trays reached the desired humidity in a lesser period.

Aging and service wear of air compressors and dryers in nuclear power plants

International Nuclear Information System (INIS)

Moyers, J.C.

1989-01-01

Compressed air systems and their associated compressors and dryers as incorporated in LWR power plants usually are not classified as safety related systems and components because their continued operation is not required to bring the plant to a safe shutdown condition. However, control air is a vital requirement for maintaining stable plant operation and its loss often results in a reactor trip and, on occasion, the actuation of engineered safety feature systems. Concerns caused by repeated instances of failures in air systems resulted in the high-priority ranking of Generic Issue No. 43, ''Reliability of Air Systems'' by the NRC. In support of the Nuclear Plant Aging Research (NPAR) Program, the Oak Ridge National Laboratory is carrying out a Phase I aging assessment of air compressors and dryers used in LWR power plants. The objectives of this study include: (1) determination of the types and ratings of equipment utilized in typical plants; (2) identification of aging and service wear stressors imposed on the machines; (3) evaluation of operating experience with the machines; (4) comparison of user and manufacturer-recommended inspection, surveillance, and monitoring (ISM) methods; and (5) the identification of any improved ISM methods that might lead to longer, more reliable, service. 2 refs

ATLAS magnet common cryogenic, vacuum, electrical and control systems

CERN Document Server

Miele, P; Delruelle, N; Geich-Gimbel, C; Haug, F; Olesen, G; Pengo, R; Sbrissa, E; Tyrvainen, H; ten Kate, H H J

2004-01-01

The superconducting Magnet System for the ATLAS detector at the LHC at CERN comprises a Barrel Toroid, two End Cap Toroids and a Central Solenoid with overall dimensions of 20 m diameter by 26 m length and a stored energy of 1.6 GJ. Common proximity cryogenic and electrical systems for the toroids are implemented. The Cryogenic System provides the cooling power for the 3 toroid magnets considered as a single cold mass (600 tons) and for the CS. The 21 kA toroid and the 8 kA solenoid electrical circuits comprise both a switch-mode power supply, two circuit breakers, water cooled bus bars, He cooled current leads and the diode resistor ramp-down unit. The Vacuum System consists of a group of primary rotary pumps and sets of high vacuum diffusion pumps connected to each individual cryostat. The Magnet Safety System guarantees the magnet protection and human safety through slow and fast dump treatment. The Magnet Control System ensures control, regulation and monitoring of the operation of the magnets. The update...

Performance of A Horizontal Cylinder Type Rotary Dryer for Drying Process ofOrganic Compost from Solid Waste Cocoa Pod

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2008-07-01

Full Text Available Cocoa pod husk is the bigest component of cocoa pod, about 70% of total ht of mature pod, and to potentially used as organic compost source. Poten tial solid waste of cocoa pod husk from a cocoa processing centre is about 15— 22 m3/ha/year. A cocoa plantation needs about 20—30 ton/ha/year of organic matters. One of important steps in compos processing technology of cocoa pod solid waste is drying process. Organic compost with 20% moisture content is more easy in handling, application, storage and distribution. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal cylinder type rotary dryer for drying process of organic compos from solid waste cocoa pod with kerosene burner as energy sources. The objective of this research is to study performance of a horizontal cylinder type rotary dryer using kerosene burner as energy source for drying process of organic compost from solid waste cocoa pod. The material used was solid waste cocoa pod with 70—75% moisture content (wet basis, 70% size particle larger than 4.76 mm, and 30% size particle less than 4.76 mm, 690—695 kg/m3 bulk density. Drying process temperatures treatment were 60OC, 80OC, and 100OC, and cylinder rotary speed treatments were 7 rpm, 10 rpm, dan 16 rpm. The results showed that dryer had capacity about 102—150 kg/h depend on drying temperature and cylinder rotary speed. Optimum operation condition at 100OC drying temperature, and 10 rpm cylinder rotary speed with drying time to reach final moisture content of 20% was 1,6 h, capacity 136,14 kg/ h, bulk density 410 kg/m3, porocity 45,15%, kerosene consumption as energy source was 2,57 l/h, and drying efficiency 68,34%. Key words : cocoa, drying, rotary dryer, compost, waste

Temperature Control System for Mushroom Dryer

Science.gov (United States)

Wibowo, I. A.; Indah, Nur; Sebayang, D.; Adam, N. H.

2018-03-01

The main problem in mushroom cultivation is the handling after the harvest. Drying is one technique to preserve the mushrooms. Traditionally, mushrooms are dried by sunshine which depends on the weather. This affects the quality of the dried mushrooms. Therefore, this paper proposes a system to provide an artificial drying for mushrooms in order to maintain their quality. The objective of the system is to control the mushroom drying process to be faster compared to the natural drying at an accurate and right temperature. A model of the mushroom dryer has been designed, built, and tested. The system comprises a chamber, heater, blower, temperature sensor and electronic control circuit. A microcontroller is used as the controller which is programmed to implement a bang-bang control that regulates the temperature of the chamber. A desired temperature is inputted as a set point of the control system. Temperature of 45 °C is chosen as the operational drying temperature. Several tests have been carried out to examine the performance of the system including drying speed, the effects of ambient conditions, and the effects of mushroom size. The results show that the system can satisfy the objective.

75 FR 37593 - Energy Conservation Program for Consumer Products: Test Procedures for Clothes Dryers and Room...

Science.gov (United States)

2010-06-29

... docket number EERE-2008-BT-TP-0010 and/or RIN 1904-AC02 in the subject line of the message. 3. Mail: Ms... DOE clothes washer test procedure), which is assumed to proportionally impact dryer load sizes. DOE... noted that IEC Standard 62087 specifies methods of measuring the power consumption of TV receivers...

Theoretical thermal-hydraulic investigations of the operational and safety features of the cold D2-moderator for SINQ

International Nuclear Information System (INIS)

Skala, K.; Spitzer, H.; Bauer, G.S.

1991-01-01

In order to be able to investigate the behaviour of the gas-liquid mixture in the rather complex vessel and pipe system of the cold D 2 -moderator with heat exchanger and ballast volume, a computational model of the system has been set up. The model was first benchmarked against experimental data from the cold moderator mockup for the second cold source at the ILL Grenoble. It was then used to predict operational parameters such as pressure, velocity, moisture content and others of the system under normal conditions with the anticipated distribution of heat influx. Finally, the case of total loss of insulating vacuum was investigated. (author)

Triple vacuum glazing: Heat transfer and basic mechanical design constraints

Energy Technology Data Exchange (ETDEWEB)

Manz, H.; Brunner, S.; Wullschleger, L. [Swiss Federal Laboratories for Materials Testing and Research (EMPA), Laboratory for Applied Physics in Building, Ueberlandstrasse 129, CH-8600 Duebendorf (Switzerland)

2006-12-15

Given the major role played by windows with regard to energy losses from buildings in cold climates, low thermal transmittance is an indispensable property of glazing in low-energy buildings. Evacuation offers the only means of achieving negligible gaseous conduction in glazing cavities. Application of low-emittance coatings to glass sheet surfaces inside the cavity reduces the radiative heat transfer. The feasibility of double vacuum glazing using arrays of support pillars between the glass sheets has been shown by other authors. This type of glazing is commercially manufactured today. Based on these achievements, our study set out to investigate heat transfer in triple vacuum glazing by means of (i) an analytical thermal network model and (ii) a numerical finite difference model. The study focused on the impact of the following parameters on thermal transmittance: emittances of glass sheet surfaces inside the cavity, support pillar radius, support pillar separation and thermal conductivity of support pillar material. The design procedure for triple vacuum glazing taking into account not only thermal but also mechanical stresses due to atmospheric pressure, i.e., to enable identification of favourable parameter sets, is presented. Our findings suggest that use of the triple vacuum glazing concept can significantly reduce the thermal transmittances achieved by the best insulation glazing units currently on the market. E.g., a centre-of-glazing thermal transmittance of less than 0.2Wm{sup -2}K{sup -1} is achievable using stainless steel support pillars, 6mm/4mm/6mm sheets of untempered soda-lime glass and four low-emittance coatings ({epsilon}=0.03). (author)

Research into Noise Generated by Domestic Appliances in the Anechoic Chamber

Directory of Open Access Journals (Sweden)

Agnė Žukauskienė

2012-12-01

Full Text Available Loud noise has a negative impact on the entire body, especially on listening. We can hear daily noise everywhere – in the street, at work or at home. The Department of Environmental Protection of Vilnius Gediminas Technical University has adjusted an anechoic chamber adapted for suppressing sound. Under the above introduced conditions, 15 appliances (5 vacuum cleaners, 5 hair dryers and 5 shaving machines have been tested. Equivalent sound pressure level of the vacuum cleaner has varied from 66 dBA to 83 dBA, that of the hair dryer has made from 64 dBA to 70 dBA and for the shaving machine – from 39 to 56 dBA.Article in Lithuanian

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-07-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidizing gas,(3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Energy aAnalysis and Kinetics of Mint Leaves Dehydration Using Vibro-Fluidized Bed Heat Pump Dryer

Directory of Open Access Journals (Sweden)

S. M Ataei Ardestani

2015-03-01

Full Text Available Fluidized bed dryers have not yet been used for drying products such as mint leaves. This could be due to high porosity and low mechanical resistance resulting in poor quality of fluidization. Applying vibration has been recommended to overcome problems such as channeling and defluidization, and hence improving the fluidization quality. In this research, a laboratory scale vibro-fluidized bed heat pump dryer was designed and constructed for drying mint leaves. The experiments were conducted at vibration frequency of 80 Hz and amplitude of 3 mm. The velocity and temperature of the inlet air was controlled by an automatic control system. Experiments were carried out at 40, 50 and 60 °C, and two methods: heat pump drying (HPD and non-heat pump drying (NHPD. The results revealed that drying process primarily occurred in the falling rate period. Effective moisture diffusivity of the samples increased with increase in drying air temperature and varied from 4.26656×10-11 to 2.95872×10-10 m2 s-1 for the HPD method, and 3.71918×10-11 to 1.29196×10-10 m2 s-1 for the NHPD method and was within the reported range of 10-9 to 10-11 m2 s-1 for drying of food materials. The activation energy was determined to be 84 kJ mol-1 for the HPD and 54.34 kJ mol-1 for the NHPD, both have very good agreement with the results of other investigators. The coefficient of performance and specific moisture evaporation rate showed the acceptable performance of the heat pump system. Moreover, the energy consumption of the dryer for the NHPD method was more than the HPD method.

MEA vacuum system

International Nuclear Information System (INIS)

Stroo, R.; Schwebke, H.; Heine, E.

1984-01-01

This report describes construction and operation of the MEA vacuum system of NIKHEF (Netherlands). First, the klystron vacuum system, beam transport system, diode pump and a triode pump are described. Next, the isolation valve and the fast valves of the vacuum system are considered. Measuring instruments, vacuum system commands and messages of failures are treated in the last chapter. (G.J.P.)

Insulation vacuum and beam vacuum overpressure release

CERN Document Server

Parma, V

2009-01-01

There is evidence that the incident of 19th September caused a high pressure build-up inside the cryostat insulation vacuum which the existing overpressure devices could not contain. As a result, high longitudinal forces acting on the insulation vacuum barriers developed and broke the floor and the floor fixations of the SSS with vacuum barriers. The consequent large longitudinal displacements of the SSS damaged chains of adjacent dipole cryo-magnets. Estimates of the helium mass flow and the pressure build- up experienced in the incident are presented together with the pressure build-up for an even more hazardous event, the Maximum Credible Incident (MCI). The strategy of limiting the maximum pressure by the installation of addition pressure relieve devices is presented and discussed. Both beam vacuum lines were ruptured during the incident in sector 3-4 giving rise to both mechanical damage and pollution of the system. The sequence, causes and effects of this damage will be briefly reviewed. We will then an...

Jets with ALICE: from vacuum to high-temperature QCD

CERN Multimedia

CERN. Geneva

2014-01-01

ALICE measures jets in pp, p-Pb and Pb-Pb collisions to study modifications of the jet fragmentation due to cold nuclear and hot QCD matter. In pp collisions ALICE has measured inclusive jet yields, the ratio of yields with different resolution R, a variety of jet shapes and the semi-inclusive rate of jets recoiling against a high transverse momentum hadron trigger. These measurements are compared to NLO calculations including hadronization corrections and to MC models. Jets in pp are primarily conceived as a vacuum reference for jet observables in p-Pb and Pb-Pb collisions. In p-Pb collisions ALICE explores cold nuclear matter effects on jet yields, jet fragmentation and dijet acoplanarity. The hot and dense medium created in heavy-ion collisions is expected to modify the fragmentation of high energy partonic projectiles leading to changes in the energy and structure of the reconstructed jets with respect to pp jets. The study of modified jets aims at understanding the detailed mechanisms of in-medium energy...

The Instituto Nacional de Pesquisas da Amazonia-INPA solar dryer: an economical alternative for wood drying; O secador solar do INPA: uma alternativa economica para secar madeira

Energy Technology Data Exchange (ETDEWEB)

Moraes-Duzat, Rejane; Barbosa, Ana Paula; Vetter, Roland [Instituto Nacional de Pesquisas da Amazonia (INPA), Manaus, AM (Brazil)]. E-mail: duzat@inpa.gov.br; apaula@inpa.gov.br

2000-07-01

As an alternative to the expensive and high energy consuming conventional dryers available at the market, INPA developed a solar wood dryer technically adequate to the climatic conditions of the Amazon region, and economically suitable to an industrial segment that could not afford large investments to dry wood. The dryer has received great acceptance by the industry due to its low cost and good operating efficiency. The prototype was dimensioned with a capacity of 5 to 8 m{sup 3} of sawn wood, which is sufficient for the needs of small sawmills or furniture shops. A total of 20 units have been installed in Brazil and other countries. Research work is underway to improve the performance of the original model, and some modifications are conducted to adapt it to dry other natural products as seeds, nuts, fruits, and herbs. (author)

Drying of mint leaves in a solar dryer and under open sun: Modelling, performance analyses

International Nuclear Information System (INIS)

Akpinar, E. Kavak

2010-01-01

In this study was investigated the thin-layer drying characteristics in solar dryer with forced convection and under open sun with natural convection of mint leaves, and, performed energy analysis and exergy analysis of solar drying process of mint leaves. An indirect forced convection solar dryer consisting of a solar air collector and drying cabinet was used in the experiments. The drying data were fitted to ten the different mathematical models. Among the models, Wang and Singh model for the forced solar drying and the natural sun drying were found to best explain thin-layer drying behaviour of mint leaves. Using the first law of thermodynamics, the energy analysis throughout solar drying process was estimated. However, exergy analysis during solar drying process was determined by applying the second law of thermodynamics. Energy utilization ratio (EUR) values of drying cabinet varied in the ranges between 7.826% and 46.285%. The values of exergetic efficiency were found to be in the range of 34.760-87.717%. The values of improvement potential varied between 0 and 0.017 kJ s -1 . Energy utilization ratio and improvement potential decreased with increasing drying time and ambient temperature while exergetic efficiency increased.

Collisionless plasma expansion into a vacuum

International Nuclear Information System (INIS)

Denavit, J.

1979-01-01

Particle simulations of the expansion of a collisionless plasma into vacuum are presented. The cases of a single-electron-temperature plasma and of a two-electron-temperature plasma are considered. The results confirm the existence of an ion front and verify the general features of self-similar solutions behind this front. A cold electron front is clearly observed in the two-electron-temperatures case. The computations also show that for a finite electron-to-ion mass ratio, m/sub e//m/sub i/, the electron thermal velocity in the expansion region is not constant, but decreases approximately linearly with xi 0 -(γ-1) xi/2, and comparison with computer simulation results show that the constant γ-1 is proportional to (Zm/sub e//m/sub i/)atsup 1/2at, where Z is the ion charge number

Advanced light source vacuum policy and vacuum guidelines for beamlines and experiment endstations

International Nuclear Information System (INIS)

Hussain, Z.

1995-08-01

The purpose of this document is to: (1) Explain the ALS vacuum policy and specifications for beamlines and experiment endstations. (2) Provide guidelines related to ALS vacuum policy to assist in designing beamlines which are in accordance with ALS vacuum policy. This document supersedes LSBL-116. The Advanced Light Source is a third generation synchrotron radiation source whose beam lifetime depends on the quality of the vacuum in the storage ring and the connecting beamlines. The storage ring and most of the beamlines share a common vacuum and are operated under ultra-high-vacuum (UHV) conditions. All endstations and beamline equipment must be operated so as to avoid contamination of beamline components, and must include proper safeguards to protect the storage ring vacuum from an accidental break in the beamline or endstation vacuum systems. The primary gas load during operation is due to thermal desorption and electron/photon induced desorption of contaminants from the interior of the vacuum vessel and its components. The desorption rates are considerably higher for hydrocarbon contamination, thus considerable emphasis is placed on eliminating these sources of contaminants. All vacuum components in a beamline and endstation must meet the ALS vacuum specifications. The vacuum design of both beamlines and endstations must be approved by the ALS Beamline Review Committee (BRC) before vacuum connections to the storage ring are made. The vacuum design is first checked during the Beamline Design Review (BDR) held before construction of the beamline equipment begins. Any deviation from the ALS vacuum specifications must be approved by the BRC prior to installation of the equipment on the ALS floor. Any modification that is incorporated into a vacuum assembly without the written approval of the BRC is done at the user's risk and may lead to rejection of the whole assembly

Stability of the Horizontal Curvature of the LHC Cryodipoles During Cold Tests

CERN Document Server

Cano, E D Fernandez; García-Pérez, J; Jeanneret, Jean Bernard; Poncet, A; Seyvet, F; Tovar-Gonzalez, A; Wildner, E; IEEE Trans. Nucl. Sci.

2006-01-01

The LHC will be composed of 1232 horizontally curved, 15 meter long, superconducting dipole magnets cooled at 1.9 K. They are supported within their vacuum vessel by three Glass Fiber Reinforced Epoxy (GFRE) support posts. Each cryodipole is individually cold tested at CERN before its installation and interconnection in the LHC 27 km circumference tunnel. As the magnet geometry under cryogenic operation is extremely important for the LHC machine aperture, a new method has been developed at CERN in order to monitor the magnet curvature change between warm and cold states. It enabled us to conclude that there is no permanent horizontal curvature change of the LHC dipole magnet between warm and cold states, although a systematic horizontal transient deformation during cool-down was detected. This deformation generates loads in the dipole supporting system; further investigation permitted us to infer this behavior to the asymmetric thermal contraction of the rigid magnet thermal shield during cool-down. Controlli...

Field electron emission from pencil-drawn cold cathodes

Energy Technology Data Exchange (ETDEWEB)

Chen, Jiangtao; Yang, Bingjun; Liu, Xiahui; Yang, Juan; Yan, Xingbin, E-mail: xbyan@licp.cas.cn [Laboratory of Clean Energy Chemistry and Materials, State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

2016-05-09

Field electron emitters with flat, curved, and linear profiles are fabricated on flexible copy papers by direct pencil-drawing method. This one-step method is free of many restricted conditions such as high-temperature, high vacuum, organic solvents, and multistep. The cold cathodes display good field emission performance and achieve high emission current density of 78 mA/cm{sup 2} at an electric field of 3.73 V/μm. The approach proposed here would bring a rapid, low-cost, and eco-friendly route to fabricate but not limited to flexible field emitter devices.

Modeling 3D conjugate heat and mass transfer for turbulent air drying of Chilean papaya in a direct contact dryer

Science.gov (United States)

Lemus-Mondaca, Roberto A.; Vega-Gálvez, Antonio; Zambra, Carlos E.; Moraga, Nelson O.

2017-01-01

A 3D model considering heat and mass transfer for food dehydration inside a direct contact dryer is studied. The k- ɛ model is used to describe turbulent air flow. The samples thermophysical properties as density, specific heat, and thermal conductivity are assumed to vary non-linearly with temperature. FVM, SIMPLE algorithm based on a FORTRAN code are used. Results unsteady velocity, temperature, moisture, kinetic energy and dissipation rate for the air flow are presented, whilst temperature and moisture values for the food also are presented. The validation procedure includes a comparison with experimental and numerical temperature and moisture content results obtained from experimental data, reaching a deviation 7-10 %. In addition, this turbulent k- ɛ model provided a better understanding of the transport phenomenon inside the dryer and sample.

Conceptual design of HANARO cold neutron source

International Nuclear Information System (INIS)

Lee, Chang Hee; Sim, Cheul Muu; Park, K. N.; Choi, Y. H.

2002-07-01

The purpose of the cold source is to increase the available neutron flux delivered to instruments at wavelength 4 ∼ 12 A. The major engineering targets of this CNS facility is established for a reach out of very high gain factors in consideration with the cold neutron flux, moderator, circulation loop, heat load, a simplicity of the maintenance of the facility, safety in the operation of the facility against the hydrogen explosion and a layout of a minimum physical interference with the present facilities. The cold source project has been divided into 5 phases: (1) pre-conceptual (2) conceptual design (3) Testing (4) detailed design and procurement (5) installation and operation. Although there is sometime overlap between the phases, in general, they are sequential. The pre-conceptual design and concept design of KCNS has been performed on elaborations of PNPI Russia and review by Technicatome, Air Liquid, CILAS France. In the design of cold neutron source, the characteristics of cold moderators have been studied to obtain the maximum gain of cold neutron, and the analysis for radiation heat, design of hydrogen system, vacuum system and helium system have been performed. The possibility for materialization of the concept in the proposed conceptual design has been reviewed in view of securing safety and installing at HANARO. Above all, the thermosiphon system to remove heat by circulation of sub-cooled two phase hydrogen has been selected so that the whole device could be installed in the reactor pool with the reduced volume. In order to secure safety, hydrogen safety has been considered on protection to prevent from hydrogen-oxygen reaction at explosion of hydrogen-oxygen e in the containment. A lay out of the installation, a maintenance and quality assurance program and a localization are included in this report. Requirements of user, regulatory, safety, operation, maintenance should be considered to be revised for detailed design, testing, installation

Sustainable implementation of solar tunnel dryers, water heaters and cookers in Nepal

Energy Technology Data Exchange (ETDEWEB)

Kovacs, Peter [Danish Energy Management, DEM for Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Shrestha, Niraj; Shakya, Prajwal Raj [Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Pokharel, Govind [Alternative Energy Promotion Centre (AEPC), Lalitpur (Nepal)

2008-07-01

The Renewable Energy Project (REP) is a joint effort of the European Union and the Government of Nepal. Main objectives of the project are to create renewable energy infrastructure and services for the benefit of rural people in remote districts of Nepal. The REP will provide solar energy systems for public services in remote districts, as well as for income generating activities e.g. agro business and tourism. The REP focuses on the installation of institutional PV systems with a total capacity of 0.850 MWp. Concurrently, a number of solar thermal systems are being provided to community organizations (COs) in rural areas of Nepal. The priority applications for the solar thermal part are solar tunnel dryers for small industries drying vegetables. fruits and herbs, solar water heaters for community centers in trekking areas and large scale solar cookers in schools. The paper describes the Renewable Energy Project's implementation program for solar thermal technology and in particular the implications on design and usefulness of the solar tunnel dryer from on-site feasibility studies carried out by the project team. REP provides a framework for a sustainable implementation of these systems by carrying out the whole process from dissemination of information to demand collection, feasibility studies, design, procurement, commissioning and user training. Hand over of ownership will take place once the equipment is installed and successfully commissioned. Monitoring during the first year of operation should conclude the project. REP is co-funded by the European Union and the Government of Nepal. (orig.)

Design, Construction and Testing of Simple Solar Maize Dryer

Directory of Open Access Journals (Sweden)

Joshua FOLARANMI

2008-12-01

Full Text Available This project reports the design, construction and testing of a simple solar maize dryer. It is design in such a way that solar radiation is not incident directly on the maize, but preheated air warmed during its flow through a low pressure thermosphonic solar energy air heater or collector made up of an insulating material (polystyrene of size 100mmx50mmx25.4mm, absorber plate (aluminium sheet painted black of size 100mmx50mm and a cover glass (5mm thickness measuring 100mmx50mm all arranged in this order contributed to the heating. The test results gave temperature above 45OC in the drying chamber, and the moisture content of 50kg of maize reduced to about 12.5% in three days of 9hours each day of drying.

Process optimization of ultrasound-assisted alcoholic-alkaline treatment for granular cold water swelling starches.

Science.gov (United States)

Zhu, Bo; Liu, Jianli; Gao, Weidong

2017-09-01

This paper reports on the process optimization of ultrasonic assisted alcoholic-alkaline treatment to prepare granular cold water swelling (GCWS) starches. In this work, three statistical approaches such as Plackett-Burman, steepest ascent path analysis and Box-Behnken design were successfully combined to investigate the effects of major treatment process variables including starch concentration, ethanol volume fraction, sodium hydroxide dosage, ultrasonic power and treatment time, and drying operation, that is, vacuum degree and drying time on cold-water solubility. Results revealed that ethanol volume fraction, sodium hydroxide dosage, applied power and ultrasonic treatment time were significant factors that affected the cold-water solubility of GCWS starches. The maximum cold-water solubility was obtained when treated at 400W of applied power for 27.38min. Optimum volume fraction of ethanol and sodium hydroxide dosage were 66.85% and 53.76mL, respectively. The theoretical values (93.87%) and the observed values (93.87%) were in reasonably good agreement and the deviation was less than 1%. Verification and repeated trial results indicated that the ultrasound-assisted alcoholic-alkaline treatment could be successfully used for the preparation of granular cold water swelling starches at room temperatures and had excellent improvement on the cold-water solubility of GCWS starches. Copyright © 2016. Published by Elsevier B.V.

Vacuum mechatronics first international workshop

Energy Technology Data Exchange (ETDEWEB)

Belinski, S.E.; Shirazi, M.; Hackwood, S.; Beni, G. (eds.) (California Univ., Santa Barbara, CA (USA))

1989-01-01

This report contains papers on the following topics: proposed epitaxial thin film growth in the ultra-vacuum of space; particle monitoring and control in vacuum processing equipment; electrostatic dust collector for use in vacuum systems; materials evaluation of an electrically noisy vacuum slip ring assembly; an overview of lubrication and associated materials for vacuum service; the usage of lubricants in a vacuum environment; guidelines and practical applications for lubrication in vacuum; recent development in leak detector and calibrator designs; the durability of ballscrews for ultrahigh vacuum; vacuum-compatible robot for self-contained manufacturing systems; the design, fabrication, and assembly of an advanced vacuum robotics system for space payload calibration; design criteria for mechanisms used in space; and concepts and requirements for semiconductor multiprocess integration in vacuum. These papers are indexed separately elsewhere.

Drying characteristics of garlic ( Allium sativum L) slices in a convective hot air dryer

Science.gov (United States)

Demiray, Engin; Tulek, Yahya

2014-06-01

The effects of drying temperatures on the drying kinetics of garlic slices were investigated using a cabinet-type dryer. The experimental drying data were fitted best to the Page and Modified Page models apart from other theoretical models to predict the drying kinetics. The effective moisture diffusivities varied from 4.214 × 10-10 to 2.221 × 10-10 m2 s-1 over the temperature range studied, and activation energy was 30.582 kJ mol-1.

Drying of Ceramic Hollow Bricks in an Industrial Tunnel Dryer: A Finite Volume Analysis

OpenAIRE

F Tavares; S Neto; E Barbosa; A Lima; C Silva

2016-01-01

This paper aims to study the drying of industrial hollow bricks in a tunnel dryer cross flow type. The theoretical model is based on mass and energy conservation equations applied to air and product. To validate the methodology, numerical and experimental results for the moisture content and the temperature of brick during the drying in an industrial scale are compared and a good correlation was obtained. Results of moisture content and temperature of the product, and temperature, relative hu...

Investigation of influence of drying agent movement on the drying process effectiveness in the gravitational shelf dryer

Directory of Open Access Journals (Sweden)

N. O. Artyukhova

2017-12-01

Full Text Available The article stands for a research of the drying process efficiency of various approaches of reciprocal movement organization of drying agent and disperse material. It focuses on the results of shelf dryer investigation. The test condition was as follows: backflow of the drying agent and disperse material movement; backflow of the drying agent and disperse material movement with the drying agent recirculation; backflow of the drying agent and disperse material movement with the bypassing of drying agent and it’s putting on separate stage of gravitational shelf dryer. The influence of the drying agent movement organization on the characteristics of disperse material and drying agent, energy costs for this process and its efficiency is shown. The recommendations of usage of represented approaches of flows movement organization depending on the desired final moisture of the material as well as its physical and chemical properties are given. The proposed ways of reciprocal flows movement organization allow to reduce the costs of drying agent heating or to increase the efficiency of moisture removal at constant energy consumption.

KAJIAN TEKNIS-EKONOMIS ALAT PENGERING PATI SAGU MODEL CROSS FLOW VIBRO FLUIDIZED BED (Study on Technical-Economic of Sago Starch Dryer Model of Cross Flow Vibro Fluidized Bed

Directory of Open Access Journals (Sweden)

Abadi Jading

2015-02-01

Full Text Available The purpose of this research was to evaluate performance of vibro cross flow fluidized bed dryer using biomass fuel for drying sago starch. The phase of research were evaluation of dryer heated by a biomass stove using coconut shell as a fuel and observation of the drying temperature, moisture content, drying time, energy analysis, and drying effiviency, as well as calculation of its economic analysis. The dryer has dimension of 200x50x1500 cm for length, width, hight, respectively, and working capacity of 35kg/process. The results showed that biomass fuel consumption for drying sago starch for 7 hours was 12740,00 MJ (70 kg/process and electricity consumption for blower and vibrator was 37,80 MJ. Furthermore, the dryer reduced moisture content of sago starch from 42% (wb to 12% (wb with temperature in the vibrator chamber of 40-60 oC and relative humidity of 50%, as well as ambient temperature of 30 3C and drying efficiency of 46,02%. Economic analysis showed that the dryer had NPV of Rp. 16.002.858, BCR of 1,53, IRR of 35%, and PBP of 3,51 years. Keywords: Cross flow, vibro fluidized bed dryer, biomass stoves, sago starch, financial analysis   ABSTRAK Tujuan penelitian ini adalah melakukan pengujian terhadap alat pengering pati berbasis sagu model cross flow vibrofluidized bed bertenaga biomassa. Tahapan penelitian meliputi pengujian alat pengering menggunakan tungku biomassa berbahan bakar tempurung kelapa dengan melakukan pengamatan suhu selama pengeringan, penurunan kadar air, waktu pengeringan, kebutuhan energi, efisiensi pengering, dan analisis finansial. Konstruksi alat pengering pati sagu model vibro fluidized bed bertenaga biomassa berukuran panjang, lebar dan tinggi masing-masing (200x50x1500 cm, serta memiliki daya tampung atau kapasitas maksimum pati sagu basah 35 kg/proses. Hasil pengujian menunjukkan bahwa alat pengering ini mampu mengeringkan pati sagu selama 7 jam, dengan konsumsi bahan bakar tempurung kelapa sebanyak 70 kg

Experimental investigation of a novel indirect solar dryer implementing PCM as energy storage medium

Energy Technology Data Exchange (ETDEWEB)

Shalaby, S.M., E-mail: saleh_shalaby@yahoo.com; Bek, M. A.

2014-07-01

Highlights: • The performance of a novel indirect solar dryer is investigated experimentally. • PCM, paraffin wax, is used as energy storage medium. • The novel ISD is suitable for drying medical plants. • Ocimum and Thevetia are dried at their prescribed drying temperatures. • The novel design maintains the desired temperature for 7 consecutive h/day. - Abstract: A novel indirect solar dryer (ISD) design using phase change material (PCM) as energy storage medium was experimentally investigated. The system consists of two identical solar air heaters, drying compartment, PCM storage units and a blower. The ISD was tested under no load with and without PCM at a wide range of mass flow rates (0.0664–0.2182 kg/s). It is found that after using the PCM, the temperature of the drying air is higher than ambient temperature by 2.5–7.5 °C after sunset for five hours at least. In addition, the mass flow rates of 0.1204 and 0.0894 kg/s give the peak values of the drying temperature when the ISD is operated with and without PCM, respectively. The novel design successfully maintains the desired temperature for seven consecutive hours every day. This helps reaching the final moisture content of Ocimum Basilicum and Thevetia Neriifolia after 12 and 18 h, respectively.

Drying kinetics of whole and sliced turmeric rhizomes (Curcuma longa L. in a solar conduction dryer

Directory of Open Access Journals (Sweden)

A. Borah

2015-09-01

Full Text Available Drying of turmeric was carried out in a solar conduction dryer (SCD. Drying air temperature was achieved around 39–51 °C for an ambient temperature in the range of 25–28 °C. Moisture content from 78.65% (wb, was reduced to 6.36% (wb and 5.50% (wb for solid and sliced samples respectively in 12 h effective drying time. Drying curve of sliced samples showed more uniform falling in comparison to that of whole samples. The average effective moisture diffusivity was found to be 1.852 × 10−10 m2 s−1 for slab samples and 1.456 × 10−10 m2 s−1 for solid samples. Out of four models tried for simulation, Page model was found as best fitted thin layer drying model when simulation was done for all the drying data. The overall thermal efficiency of the dryer was found to be 55%. Drying of sliced rhizomes showed better drying kinetics and effective drying time could be reduced by slicing instead of drying in whole form.

Magnetically induced vacuum decay

International Nuclear Information System (INIS)

Xue Shesheng

2003-01-01

We study the fermionic vacuum energy of vacua with and without application of an external magnetic field. The energetic difference of two vacua leads to the vacuum decaying and the vacuum energy being released. In the context of quantum field theories, we discuss why and how the vacuum energy can be released by spontaneous photon emission and/or paramagnetically screening the external magnetic field. In addition, we quantitatively compute the vacuum energy released, the paramagnetic screening effect, and the rate and spectrum of spontaneous photon emission. The possibilities of experimentally detecting such an effect of vacuum-energy release and that this effect accounts for the anomalous x-ray pulsar are discussed

Optical coupling of cold atoms to a levitated nanosphere

Science.gov (United States)

Montoya, Cris; Witherspoon, Apryl; Fausett, Jacob; Lim, Jason; Kitching, John; Geraci, Andrew

2017-04-01

Cooling mechanical oscillators to their quantum ground state enables the study of quantum phenomena at macroscopic levels. In many cases, the temperature required to cool a mechanical mode to the ground state is below what current cryogenic systems can achieve. As an alternative to cooling via cryogenic systems, it has been shown theoretically that optically trapped nanospheres could reach the ground state by sympathetically cooling the spheres via cold atoms. Such cooled spheres can be used in quantum limited sensing and matter-wave interferometry, and could also enable new hybrid quantum systems where mechanical oscillators act as transducers. In our setup, optical fields are used to couple a sample of cold Rubidium atoms to a nanosphere. The sphere is optically levitated in a separate vacuum chamber, while the atoms are trapped in a 1-D optical lattice and cooled using optical molasses. This work is partially supported by NSF, Grant No. PHY-1506431.

Research of the cold shield in cryogenic liquid storage

Science.gov (United States)

Chen, L. B.; Zheng, J. P.; Wu, X. L.; Cui, C.; Zhou, Y.; Wang, J. J.

2017-12-01

To realize zero boil-off storage of cryogenic liquids, a cryocooler that can achieve a temperature below the boiling point temperature of the cryogenic liquid is generally needed. Taking into account that the efficiency of the cryocooler will be higher at a higher operating temperature, a novel thermal insulation system using a sandwich container filled with cryogenic liquid with a higher boiling point as a cold radiation shield between the cryogenic tank and the vacuum shield in room temperature is proposed to reduce the electricity power consumption. A two-stage cryocooler or two separate cryocoolers are adopted to condense the evaporated gas from the cold shield and the cryogenic tank. The calculation result of a 55 liter liquid hydrogen tank with a liquid nitrogen shield shows that only 14.4 W of electrical power is needed to make all the evaporated gas condensation while 121.7 W will be needed without the liquid nitrogen shield.

Qualidade fisiológica de sementes de sorgo coletadas em diferentes pontos de um secador Physiological quality of sorghum seeds collected at different points in the dryer

Directory of Open Access Journals (Sweden)

Jadir N. da Silva

2001-12-01

Full Text Available Neste trabalho, avaliou-se a qualidade fisiológica e se quantificaram os possíveis gradientes de umidade de sementes de sorgo BR 601, durante o armazenamento. Utilizaram-se amostras coletadas em secador de camada fixa vertical, com duto central perfurado e distribuição radial de ar. Os pontos amostrais no secador se distanciavam 0,10; 0,30 e 0,50 m em relação à lateral do duto central de ar e nas alturas de 0,85; 2,02 e 3,64 m da base do secador, com capacidade de 8 t, além de uma amostra média (M que representou os três pontos radiais, respectivamente. Armazenou-se o sorgo durante nove meses e se avaliou a germinação, vigor e umidade do produto no terceiro, sexto e nono meses de armazenamento. Não houve diferença na qualidade fisiológica das sementes nas diferentes alturas e distâncias em relação ao duto central de ar do secador, em relação à média (M durante o armazenamento, mas no decorrer deste, a queda de qualidade foi mais evidente no teste de frio, obtida no nono mês de armazenamento.The objective of this work was to evaluate the physiological quality and possible moisture gradients in seeds of sorghum BR 601, during storage. Samples from a vertical fixed-bed dryer with a perforated central duct and radial air distribution were used. In the dryer, the sample points were located at 0.10, 0.30 and 0.50 m distances in relation to the lateral of the central air duct. A composite sample was also collected and used as the control in relation to the others, at the respective heights. These sampling procedures were followed at heights of 0.85; 2.02 and 3.64 m from the dryer base. Within each height and distance relative to the air duct, the collected samples were stored during nine months and evaluated for germination and vigor. At the third, sixth and ninth months after storage, the samples were evaluated for possible differences in quality and seed moisture gradient in comparison to the composite sample. No differences

Electroweak vacuum instability and renormalized Higgs field vacuum fluctuations in the inflationary universe

Energy Technology Data Exchange (ETDEWEB)

Kohri, Kazunori [Institute of Particle and Nuclear Studies, KEK, 1-1 Oho, Tsukuba 305-0801 (Japan); Matsui, Hiroki, E-mail: kohri@post.kek.jp, E-mail: matshiro@post.kek.jp [The Graduate University for Advanced Studies (SOKENDAI), 1-1 Oho, Tsukuba 305-0801 (Japan)

2017-08-01

In this work, we investigated the electroweak vacuum instability during or after inflation. In the inflationary Universe, i.e., de Sitter space, the vacuum field fluctuations < δ φ {sup 2} > enlarge in proportion to the Hubble scale H {sup 2}. Therefore, the large inflationary vacuum fluctuations of the Higgs field < δ φ {sup 2} > are potentially catastrophic to trigger the vacuum transition to the negative-energy Planck-scale vacuum state and cause an immediate collapse of the Universe. However, the vacuum field fluctuations < δ φ {sup 2} >, i.e., the vacuum expectation values have an ultraviolet divergence, and therefore a renormalization is necessary to estimate the physical effects of the vacuum transition. Thus, in this paper, we revisit the electroweak vacuum instability from the perspective of quantum field theory (QFT) in curved space-time, and discuss the dynamical behavior of the homogeneous Higgs field φ determined by the effective potential V {sub eff}( φ ) in curved space-time and the renormalized vacuum fluctuations < δ φ {sup 2} >{sub ren} via adiabatic regularization and point-splitting regularization. We simply suppose that the Higgs field only couples the gravity via the non-minimal Higgs-gravity coupling ξ(μ). In this scenario, the electroweak vacuum stability is inevitably threatened by the dynamical behavior of the homogeneous Higgs field φ, or the formations of AdS domains or bubbles unless the Hubble scale is small enough H < Λ {sub I} .

Simulation of Solar Heat Pump Dryer Directly Driven by Photovoltaic Panels

Science.gov (United States)

Houhou, H.; Yuan, W.; Wang, G.

2017-05-01

This paper investigates a new type of solar heat pump dryer directly driven by photovoltaic panels. In order to design this system, a mathematical model has been established describing the whole drying process, including models of key components and phenomena of heat and mass transfer at the product layer and the air. The results of simulation at different drying air temperatures and velocities have been calculated and it indicate that the temperature of drying air is crucial external parameter compared to the velocity, with the increase of drying temperature from 45°C to 55°C, the product moisture content (Kg water/Kg dry product) decreased from 0.75 Kg/Kg to 0.3 Kg/Kg.

Vacuum system for ISABELLE

International Nuclear Information System (INIS)

Hobson, J.P.

1975-01-01

An analysis is presented of the proposed vacuum system for the planned ISABELLE storage rings with respect to acceptability and practicality from the vacuum viewport. A comparison is made between the proposed vacuum system and the vacuum system at the CERN ISR, and some comments on various design and operational parameters are made

Vacuum extraction

DEFF Research Database (Denmark)

Maagaard, Mathilde; Oestergaard, Jeanett; Johansen, Marianne

2012-01-01

Objectives. To develop and validate an Objective Structured Assessment of Technical Skills (OSATS) scale for vacuum extraction. Design. Two-part study design: Primarily, development of a procedure-specific checklist for vacuum extraction. Hereafter, validation of the developed OSATS scale for vac...

State of Washington Department of Health Radioactive air emissions notice of construction phase 1 for spent nuclear fuel project - cold vacuum drying facility, project W-441

Energy Technology Data Exchange (ETDEWEB)

Turnbaugh, J.E.

1996-08-15

This notice of construction (NOC) provides information regarding the source and the estimated annual possession quantity resulting from operation of the Cold Vacuum Drying Facility (CVDF). Additional details on emissions generated by the operation of the CVDF will be discussed again in the Phase 11 NOC. This document serves as a NOC pursuant to the requirements of WAC 246-247-060 for the completion of Phase I NOC, defined as the pouring of concrete for the foundation flooring, construction of external walls, and construction of the building excluding the installation of CVDF process equipment. A Phase 11 NOC will be submitted for approval prior to installing and is defined as the completion of the CVDF, which consisted installation of process equipment, air emissions control, and emission monitoring equipment. About 80 percent of the U.S. Department of Energy`s spent nuclear fuel (SNF) inventory is stored under water in the Hanford Site K Basins. Spent nuclear fuel in the K West Basin is contained in closed canisters while the SNF in the K East Basin is in open canisters, which allow free release of corrosion products to the K East Basin water.

Detection of cold pain, cold allodynia and cold hyperalgesia in freely behaving rats

Directory of Open Access Journals (Sweden)

Woolf Clifford J

2005-12-01

Full Text Available Abstract Background Pain is elicited by cold, and a major feature of many neuropathic pain states is that normally innocuous cool stimuli begin to produce pain (cold allodynia. To expand our understanding of cold induced pain states we have studied cold pain behaviors over a range of temperatures in several animal models of chronic pain. Results We demonstrate that a Peltier-cooled cold plate with ± 1°C sensitivity enables quantitative measurement of a detection withdrawal response to cold stimuli in unrestrained rats. In naïve rats the threshold for eliciting cold pain behavior is 5°C. The withdrawal threshold for cold allodynia is 15°C in both the spared nerve injury and spinal nerve ligation models of neuropathic pain. Cold hyperalgesia is present in the spared nerve injury model animals, manifesting as a reduced latency of withdrawal response threshold at temperatures that elicit cold pain in naïve rats. We also show that following the peripheral inflammation produced by intraplantar injection of complete Freund's adjuvant, a hypersensitivity to cold occurs. Conclusion The peltier-cooled provides an effective means of assaying cold sensitivity in unrestrained rats. Behavioral testing of cold allodynia, hyperalgesia and pain will greatly facilitate the study of the neurobiological mechanisms involved in cold/cool sensations and enable measurement of the efficacy of pharmacological treatments to reduce these symptoms.

VAC*TRAX - thermal desorption for mixed wastes

Energy Technology Data Exchange (ETDEWEB)

McElwee, M.J.; Palmer, C.R. [RUST-Clemson Technical Center, Anderson, SC (United States)

1995-10-01

The patented VAC*TRAX process was designed in response to the need to remove organic constituents from mixed waste, waste that contains both a hazardous (RCRA or TSCA regulated) component and a radioactive component. Separation of the mixed waste into its hazardous and radioactive components allows for ultimate disposal of the material at existing, permitted facilities. The VAC*TRAX technology consists of a jacketed vacuum dryer followed by a condensing train. Solids are placed in the dryer and indirectly heated to temperatures as high as 2600{degrees}C, while a strong vacuum (down to 50 mm Hg absolute pressure) is applied to the system and the dryer is purged with a nitrogen carrier gas. The organic contaminants in the solids are thermally desorbed, swept up in the carrier gas and into the condensing train where they are cooled and recovered. The dryer is fitted with a filtration system that keeps the radioactive constituents from migrating to the condensate. As such, the waste is separated into hazardous liquid and radioactive solid components, allowing for disposal of these streams at a permitted incinerator or a radioactive materials landfill, respectively. The VAC*TRAX system is designed to be highly mobile, while minimizing the operational costs with a simple, robust process. These factors allow for treatment of small waste streams at a reasonable cost.

Gas Condensates onto a LHC Type Cryogenic Vacuum System Subjected to Electron Cloud

CERN Multimedia

Baglin, V

2004-01-01

In the Large Hadron Collider (LHC), the gas desorbed via photon stimulated molecular desorption or electron stimulated molecular desorption will be physisorbed onto the beam screen held between 5 and 20 K. Studies of the effects of the electron cloud onto a LHC type cryogenic vacuum chamber have been done with the cold bore experiment (COLDEX) installed in the CERN Super Proton Synchrotron (SPS). Experiments performed with gas condensates such as H2, H2O, CO and CO2 are described. Implications for the LHC design and operation are discussed.

Thermo-mechanical design methodology for ITER cryo-distribution cold boxes

International Nuclear Information System (INIS)

Shukla, Vinit; Patel, Pratik; Vaghela, Hiten; Das, Jotirmoy; Shah, Nitin; Bhattacharya, Ritendra; Sarkar, Biswanath; Chang, Hyun-sik

2015-01-01

The ITER cryo-distribution system is in charge of the proper distribution of the cryogen at required mass flow rate, pressure and temperature level to the users namely; the superconducting magnets and cryopumps. The cryo-distribution also acts as a thermal buffer in order to run the cryo-plant as much as possible at a steady state condition. A typical cryo-distribution cold box is equipped with mainly liquid helium bath with heat exchangers, cryogenic valves, cold circulating pump and cold compressor. During the intended operation life of ITER, several loads on the cryo-distribution system are envisaged, these are, gravity/assembly loads, nominal pressure/temperature, test pressure/temperature, purge pressure, thermo-mechanical loads due to break of insulation vacuum, transport acceleration and seismic loads. Single loads or combinations of them can act on the cryo-distribution system and its components; therefore, it is very important to analyze the behavior of the system and components under the influence of these loads or combinations. Possible load combinations for the cryo-distribution system will be analyzed and will lead to the basis of the design. This paper will focus on the understanding of the nature of the loads and their combinations for the ITER cryo-distribution as well as their impacts on the design. A representative model of a cold box is considered on which the load combinations have been applied in order to understand their impacts on the design of the cryo-distribution. Also the worst-impact loads or their combination which drive the design of cryo-distribution cold boxes will be derived. (author)

Cosmic vacuum

International Nuclear Information System (INIS)

Chernin, Artur D

2001-01-01

Recent observational studies of distant supernovae have suggested the existence of cosmic vacuum whose energy density exceeds the total density of all the other energy components in the Universe. The vacuum produces the field of antigravity that causes the cosmological expansion to accelerate. It is this accelerated expansion that has been discovered in the observations. The discovery of cosmic vacuum radically changes our current understanding of the present state of the Universe. It also poses new challenges to both cosmology and fundamental physics. Why is the density of vacuum what it is? Why do the densities of the cosmic energy components differ in exact value but agree in order of magnitude? On the other hand, the discovery made at large cosmological distances of hundreds and thousands Mpc provides new insights into the dynamics of the nearby Universe, the motions of galaxies in the local volume of 10 - 20 Mpc where the cosmological expansion was originally discovered. (reviews of topical problems)

Cosmic vacuum

Energy Technology Data Exchange (ETDEWEB)

Chernin, Artur D [P.K. Shternberg State Astronomical Institute at the M.V. Lomonosov Moscow State University, Moscow (Russian Federation)

2001-11-30

Recent observational studies of distant supernovae have suggested the existence of cosmic vacuum whose energy density exceeds the total density of all the other energy components in the Universe. The vacuum produces the field of antigravity that causes the cosmological expansion to accelerate. It is this accelerated expansion that has been discovered in the observations. The discovery of cosmic vacuum radically changes our current understanding of the present state of the Universe. It also poses new challenges to both cosmology and fundamental physics. Why is the density of vacuum what it is? Why do the densities of the cosmic energy components differ in exact value but agree in order of magnitude? On the other hand, the discovery made at large cosmological distances of hundreds and thousands Mpc provides new insights into the dynamics of the nearby Universe, the motions of galaxies in the local volume of 10 - 20 Mpc where the cosmological expansion was originally discovered. (reviews of topical problems)

Modification of Indirect Solar Dryer for Simplicia Production

Science.gov (United States)

Purnomo, C. W.; Indarti, S.

2018-03-01

Simplicia is natural ingredient for herbal medicine that has been subjected to drying only. This study aims to develop an appropriate drying equipment to produce dried leaves of sambung nyawa (Gynura procumbens (Lour.) Merr.) or also called “longevity spinach”. Typical indirect solar drier was modified to be able to process more fresh leaves in order to speed up the production. The modification was done using double solar collector and wind powered ventilation. The double solar collector was applied in order to collect more solar energy for larger dimension of drying chamber, while the wind-ventilator was installed to provide forced convection of hot air flow inside the dryer. The drying kinetic including the drying constants were investigated using three common thin layer drying equations to model the drying behavior of the leaves. The moisture ratio (MR) depletion with respect to the drying time (t) of the leaves can be well represented by equation of MR=1.1732exp(-0.0993.t)-0.1732exp(-17.3871.t).

Vacuum level effects on gait characteristics for unilateral transtibial amputees with elevated vacuum suspension.

Science.gov (United States)

Xu, Hang; Greenland, Kasey; Bloswick, Donald; Zhao, Jie; Merryweather, Andrew

2017-03-01

The elevated vacuum suspension system has demonstrated unique health benefits for amputees, but the effect of vacuum pressure values on gait characteristics is still unclear. The purpose of this study was to investigate the effects of elevated vacuum levels on temporal parameters, kinematics and kinetics for unilateral transtibial amputees. Three-dimensional gait analysis was conducted in 9 unilateral transtibial amputees walking at a controlled speed with five vacuum levels ranging from 0 to 20inHg, and also in 9 able-bodied subjects walking at self-preferred speed. Repeated ANOVA and Dunnett's t-test were performed to determine the effect of vacuum level and limb for within subject and between groups. The effect of vacuum level significantly affected peak hip external rotation and external knee adduction moment. Maximum braking and propulsive ground reaction forces generally increased for the residual limb and decreased for the intact limb with increasing vacuum. Additionally, the intact limb experienced an increased loading due to gait asymmetry for several variables. There was no systematic vacuum level effect on gait. Higher vacuum levels, such as 15 and 20inHg, were more comfortable and provided some relief to the intact limb, but may also increase the risk of osteoarthritis of the residual limb due to the increased peak external hip and knee adduction moments. Very low vacuum should be avoided because of the negative effects on gait symmetry. A moderate vacuum level at 15inHg is suggested for unilateral transtibial amputees with elevated vacuum suspension. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of fast heating electron beam annealing setup for ultra high vacuum chamber

Energy Technology Data Exchange (ETDEWEB)

Das, Sadhan Chandra [UGC-DAE Consortium For Scientific Research, University Campus, Khandwa Road, Indore 452 001, MP (India); School of Electronics, Devi Ahilya University, Indore 452001, MP (India); Institute of Physics, University of Greifswald, Felix Hausdroff Str. 6 (Germany); Majumdar, Abhijit, E-mail: majuabhijit@gmail.com, E-mail: majumdar@uni-greifswald.de; Hippler, R. [Institute of Physics, University of Greifswald, Felix Hausdroff Str. 6 (Germany); Katiyal, Sumant [School of Electronics, Devi Ahilya University, Indore 452001, MP (India); Shripathi, T. [UGC-DAE Consortium For Scientific Research, University Campus, Khandwa Road, Indore 452 001, MP (India)

2014-02-15

We report the design and development of a simple, electrically low powered and fast heating versatile electron beam annealing setup (up to 1000 °C) working with ultra high vacuum (UHV) chamber for annealing thin films and multilayer structures. The important features of the system are constant temperature control in UHV conditions for the temperature range from room temperature to 1000 ºC with sufficient power of 330 W, at constant vacuum during annealing treatment. It takes approximately 6 min to reach 1000 °C from room temperature (∼10{sup −6} mbar) and 45 min to cool down without any extra cooling. The annealing setup consists of a UHV chamber, sample holder, heating arrangement mounted on suitable UHV electrical feed-through and electronic control and feedback systems to control the temperature within ±1 ºC of set value. The outside of the vacuum chamber is cooled by cold air of 20 °C of air conditioning machine used for the laboratory, so that chamber temperature does not go beyond 50 °C when target temperature is maximum. The probability of surface oxidation or surface contamination during annealing is examined by means of x-ray photoelectron spectroscopy of virgin Cu sample annealed at 1000 °C.

Development of fast heating electron beam annealing setup for ultra high vacuum chamber

International Nuclear Information System (INIS)

Das, Sadhan Chandra; Majumdar, Abhijit; Hippler, R.; Katiyal, Sumant; Shripathi, T.

2014-01-01

We report the design and development of a simple, electrically low powered and fast heating versatile electron beam annealing setup (up to 1000 °C) working with ultra high vacuum (UHV) chamber for annealing thin films and multilayer structures. The important features of the system are constant temperature control in UHV conditions for the temperature range from room temperature to 1000 ºC with sufficient power of 330 W, at constant vacuum during annealing treatment. It takes approximately 6 min to reach 1000 °C from room temperature (∼10 −6 mbar) and 45 min to cool down without any extra cooling. The annealing setup consists of a UHV chamber, sample holder, heating arrangement mounted on suitable UHV electrical feed-through and electronic control and feedback systems to control the temperature within ±1 ºC of set value. The outside of the vacuum chamber is cooled by cold air of 20 °C of air conditioning machine used for the laboratory, so that chamber temperature does not go beyond 50 °C when target temperature is maximum. The probability of surface oxidation or surface contamination during annealing is examined by means of x-ray photoelectron spectroscopy of virgin Cu sample annealed at 1000 °C

Introduction to vacuum technology: supplementary study material developed for IVS sponsored vacuum courses

International Nuclear Information System (INIS)

Bhusan, K.G.

2008-01-01

Vacuum technology has advanced to a large extent mainly from the demands of experimental research scientists who have more than ever understood the need for clean very low pressure environments. This need only seems to increase as the lowest pressures achievable in a laboratory setup are dropping down by the decade. What is not usually said is that conventional techniques of producing ultrahigh vacuum have also undergone a metamorphosis in order to cater to the multitude of restrictions in modern day scientific research. This book aims to give that practical approach to vacuum technology. The basics are given in the first chapter with more of a definition oriented approach - which is practically useful. The second chapter deals with the production of vacuum and ultrahigh vacuum with an emphasis on the working principles of several pumps and their working pressure ranges. Measurement of low pressures, both total and partial is presented in the third chapter with a note on leak detection and mass spectrometric techniques. Chapter 4 gives an overview of the materials that are vacuum compatible and their material properties. Chapter 5 gives the necessary methods to be followed for cleaning of vacuum components especially critical if ultrahigh vacuum environment is required. The practical use of a ultrahigh vacuum environment is demonstrated in Chapter 6 for production of high quality thin films through vapour deposition

New class of microminiature Joule — Thomson refrigerator and vacuum package

Science.gov (United States)

Paugh, Robert L.

1990-12-01

Progress is reported on the development of a two-stage, fast cooldown Joule — Thomson refrigerator using nitrogen gas and a nitrogen — hydrocarbon gas mixture as the refrigerants. The refrigerator incorporates a microminiature Venturi pump to reduce the pressure of the exhaust of the main boiler to bring the operating temperature of the cold stage to < 70 K in as little as 10 s. The vacuum package for the refrigerator contains no organic materials and is designed to provide a ten year shelf life. Special glass strengthening techniques are being used to achieve cooler survival of acceleration tests of up to 100 000g.

Evaluation and mitigation of tritium memory in detritiation dryers

International Nuclear Information System (INIS)

Malara, C.; Ricapito, I.; Edwards, R.A.H.; Toci, F.

1999-01-01

In atmospheric detritiation, and other tritium processes, tritium is adsorbed on zeolites (molecular sieves) in the form of tritiated water. Regeneration removes almost all the physically adsorbed water, but a proportion remains permanently in the zeolite and binder structure as chemically bound water or hydroxyl groups. Exchange between adsorbed water and bound water means that tritiated water is retained in the structure after regeneration. At the end of its life, the zeolite therefore constitutes a tritiated waste. Furthermore, if an atmosphere detritiation dryer (ADD) gets highly contaminated from a tritium spill, retained tritium contaminates both the small amount of vapour leaving the bed during the next drying cycle, and the water produced in the subsequent regeneration. This report first describes experiments to measure the tritiated water retained in a 5A zeolite bed after standard regeneration treatments, and then investigates strategies to mitigate the effect: more thorough regeneration and isotope swamping or elution. The effect of zeolite ageing after thermal cycling is also seen. (orig.)

Drying process optimization for an API solvate using heat transfer model of an agitated filter dryer.

Science.gov (United States)

Nere, Nandkishor K; Allen, Kimberley C; Marek, James C; Bordawekar, Shailendra V

2012-10-01

Drying an early stage active pharmaceutical ingredient candidate required excessively long cycle times in a pilot plant agitated filter dryer. The key to faster drying is to ensure sufficient heat transfer and minimize mass transfer limitations. Designing the right mixing protocol is of utmost importance to achieve efficient heat transfer. To this order, a composite model was developed for the removal of bound solvent that incorporates models for heat transfer and desolvation kinetics. The proposed heat transfer model differs from previously reported models in two respects: it accounts for the effects of a gas gap between the vessel wall and solids on the overall heat transfer coefficient, and headspace pressure on the mean free path length of the inert gas and thereby on the heat transfer between the vessel wall and the first layer of solids. A computational methodology was developed incorporating the effects of mixing and headspace pressure to simulate the drying profile using a modified model framework within the Dynochem software. A dryer operational protocol was designed based on the desolvation kinetics, thermal stability studies of wet and dry cake, and the understanding gained through model simulations, resulting in a multifold reduction in drying time. Copyright © 2012 Wiley-Liss, Inc.

Vacuum fluctuations in an ancestor vacuum: A possible dark energy candidate

Science.gov (United States)

Aoki, Hajime; Iso, Satoshi; Lee, Da-Shin; Sekino, Yasuhiro; Yeh, Chen-Pin

2018-02-01

We consider an open universe created by bubble nucleation, and study possible effects of our "ancestor vacuum," a de Sitter space in which bubble nucleation occurred, on the present universe. We compute vacuum expectation values of the energy-momentum tensor for a minimally coupled scalar field, carefully taking into account the effect of the ancestor vacuum by the Euclidean prescription. We pay particular attention to the so-called supercurvature mode, a non-normalizable mode on a spatial slice of the open universe, which has been known to exist for sufficiently light fields. This mode decays in time most slowly, and may leave residual effects of the ancestor vacuum, potentially observable in the present universe. We point out that the vacuum energy of the quantum field can be regarded as dark energy if mass of the field is of order the present Hubble parameter or smaller. We obtain preliminary results for the dark energy equation of state w (z ) as a function of the redshift.

Comparison of Linear and Nonlinear Model Predictive Control for Optimization of Spray Dryer Operation

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2015-01-01

In this paper, we compare the performance of an economically optimizing Nonlinear Model Predictive Controller (E-NMPC) to a linear tracking Model Predictive Controller (MPC) for a spray drying plant. We find in this simulation study, that the economic performance of the two controllers are almost...... equal. We evaluate the economic performance with an industrially recorded disturbance scenario, where unmeasured disturbances and model mismatch are present. The state of the spray dryer, used in the E-NMPC and MPC, is estimated using Kalman Filters with noise covariances estimated by a maximum...

Design and measured performance of a solar chimney for natural-circulation solar-energy dryers

International Nuclear Information System (INIS)

Ekechukwu, O.V.; Norton, B.

1995-10-01

The design and construction of a solar chimney which was undertaken as part of a study on natural-circulation solar-energy dryers is reported. The experimental solar chimney consists of a 5.3m high and 1.64m diameter cylindrical polyethylene-clad vertical chamber, supported structurally by steel framework and draped internally with a selectively-absorbing surface. The performance of the chimney which was monitored extensively with and without the selective surface in place (to study the effectiveness of this design option) is also reported. (author). 14 refs, 7 figs

Progress toward uranium scrap recycling via electron beam cold hearth refining

International Nuclear Information System (INIS)

McKoon, R.H.

1994-01-01

A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6%-niobium (U-6Nb) alloy ingots has been demonstrated using Virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented

Progress toward uranium scrap recycling via Electron Cold Hearth Refining (EBCHR)

International Nuclear Information System (INIS)

McKoon, R.H.

1994-01-01

A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6% - niobium (U-6Nb) alloy ingots has been demonstrated using virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented

Confinement of ultra-cold neutron in a multiple cusp magnetic field

Energy Technology Data Exchange (ETDEWEB)

Akiyama, Nobumichi; Inoue, Nobuyuki; Nihei, Hitoshi; Kinosita, Ken-ichi [Tokyo Univ. (Japan). Faculty of Engineering

1996-08-01

A new confinement system of ultra-cold neutrons is proposed. The neutron bottle is made of a rectangular vacuum chamber with the size of 40 cm x 40 cm x 30 cm covered with arrays of bar type permanent magnets. The operation of bottle requires neither cooling system nor high electric power supply, and thereby the bottle is appropriate to use in the room which is located in controlled area. The maximum kinetic energy of neutrons confined is 20 neV. Experimental scheme to test the performance of the bottle is described. (author)

Coil-On-Plug Ignition for LOX/Methane Liquid Rocket Engines in Thermal Vacuum Environments

Science.gov (United States)

Melcher, John C.; Atwell, Matthew J.; Morehead, Robert L.; Hurlbert, Eric A.; Bugarin, Luz; Chaidez, Mariana

2017-01-01

A coil-on-plug ignition system has been developed and tested for Liquid Oxygen (LOX) / liquid methane rocket engines operating in thermal vacuum conditions. The igniters were developed and tested as part of the Integrated Cryogenic Propulsion Test Article (ICPTA), previously tested as part of the Project Morpheus test vehicle. The ICPTA uses an integrated, pressure-fed, cryogenic LOX/methane propulsion system including a reaction control system (RCS) and a main engine. The ICPTA was tested at NASA Glenn Research Center's Plum Brook Station in the Spacecraft Propulsion Research Facility (B-2) under vacuum and thermal vacuum conditions. In order to successfully demonstrate ignition reliability in the vacuum conditions and eliminate corona discharge issues, a coil-on-plug ignition system has been developed. The ICPTA uses spark-plug ignition for both the main engine igniter and the RCS. The coil-on-plug configuration eliminates the conventional high-voltage spark plug cable by combining the coil and the spark-plug into a single component. Prior to ICPTA testing at Plum Brook, component-level reaction control engine (RCE) and main engine igniter testing was conducted at NASA Johnson Space Center (JSC), which demonstrated successful hot-fire ignition using the coil-on-plug from sea-level ambient conditions down to 10(exp.-2) torr. Integrated vehicle hot-fire testing at JSC demonstrated electrical and command/data system performance. Lastly, Plum Brook testing demonstrated successful ignitions at simulated altitude conditions at 30 torr and cold thermal-vacuum conditions at 6 torr. The test campaign successfully proved that coil-on-plug technology will enable integrated LOX/methane propulsion systems in future spacecraft.

Mushrooms dehydration in a hybrid-solar dryer, using a phase change material

International Nuclear Information System (INIS)

Reyes, Alejandro; Mahn, Andrea; Vásquez, Francisco

2014-01-01

Highlights: • Mushroom slices were dehydrated in a hybrid solar dryer. • Drying and dehydrated kinetics were adjusted with models. • Effective diffusivity, were estimated considering or not shrinkage. • Paraffin wax as a phase change material was used in an accumulator of solar energy. - Abstract: Mushrooms were dehydrated in a hybrid solar dryer provided with a solar panel of a total exposed surface of 10 m 2 , electric resistances and paraffin wax as a phase change material. Mushrooms were cut in 8 mm or 12 mm slices. At the outlet of the drying chamber the air was recycled (70% or 80%) and the air temperature was adjusted to 60 °C. At the outlet of the solar panel the air temperature rose up to 30 °C above the ambient temperature, depending on solar radiation level. The effective diffusivity, estimated by the Simplified Constant Diffusivity Model, considering or not shrinkage, fluctuated between 2.5 · 10 −10 m 2 /s and 8.4 · 10 −10 m 2 /s with R 2 higher than 0.99, agreeing with values reported in literature. The empirical Page’s model resulted in a better adjustment, with R 2 above 0.998. In all runs the dehydrated mushrooms showed a notorious darkening and shrinkage. Rehydration assays at 30 °C showed that in less than 30 min rehydrated mushrooms reached a moisture content of 1.91 (dry basis). Rehydrated mushrooms had a higher hardness compared with fresh mushrooms. The Simplified Constant Diffusivity Model and the Peleg’s model adjusted to the rehydration data with RMSE values below 0.080. Thermal efficiency fluctuated between 22% and 62%, while the efficiency of the accumulator panel varied between 10% and 21%. The accumulator allowed reducing the electric energy input

Analysis of efficiency of a solar dryer tunnel type of mango pulp; Analisis de la eficiencia de un secador solar tipo tunel para pulpa de mango

Energy Technology Data Exchange (ETDEWEB)

Chagoyan Serrano, Jose [Universidad Autonoma de Baja California Sur, La Paz, Baja California Sur (Mexico)

2000-07-01

A new method to assess the performance of a solar dryer is presented. It describes energy efficiency indicators to improve a commercial dryer design. First, a preliminary dryer design procedure is described step by step. Then, two different modes of a tunnel dryer are investigated: Batch and semi-continue operations. The results of the analysis show that, the thermal efficiency is not sufficient to rate de dryer performance. It is necessary to include the productivity of the drying process and the quality of the dried fruit. The drying process and productivity tend to go hand-in-hand but in opposite directions. That is to say, raising the thermal efficiency reduce the process productivity and conversely. The analysis also suggests that an agreement between the efficiency, productivity and the quality must be specified in the drier design. [Spanish] Se presenta un procedimiento nuevo para evaluar la operacion de un secador solar, con el cual se precisan indicadores de la eficiencia que pueden ser utiles para mejorar el diseno del equipo. Se empieza por describir los pasos de un procedimiento de diseno preliminar de un sistema de secado. Despues, se analizan cualitativamente dos secadores: uno que opera por lotes y el otro de modo semicontinuo. Los resultados del analisis muestran que, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar encuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar en cuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica solo se puede aumentar a costa de la productividad y viceversa

Comparison of mathematical models and artificial neural networks for prediction of drying kinetics of mushroom in microwave vacuum dryer

Directory of Open Access Journals (Sweden)

Ghaderi A.

2012-01-01

Full Text Available Drying characteristics of button mushroom slices were determined using microwave vacuum drier at various powers (130, 260, 380, 450 W and absolute pressures (200, 400, 600, 800 mbar. To select a suitable mathematical model, 6 thin-layer drying models were fitted to the experimental data. The fitting rates of models were assessed based on three parameters; highest R2, lowest chi square ( and root mean square error (RMSE. In addition, using the experimental data, an ANN trained by standard back-propagation algorithm, was developed in order to predict moisture ratio (MR and drying rate (DR values based on the three input variables (drying time, absolute pressure, microwave power. Different activation functions and several rules were used to assess percentage error between the desired and the predicted values. According to our findings, Midilli et al. model showed a reasonable fitting with experimental data. While, the ANN model showed its high capability to predict the MR and DR quite well with determination coefficients (R2 of 0.9991, 0.9995 and 0.9996 for training, validation and testing, respectively. Furthermore, their predictions Mean Square Error were 0.00086, 0.00042 and 0.00052, respectively.

Cold dark matter confronts the cosmic microwave background - Large-angular-scale anisotropies in Omega sub 0 + lambda 1 models

Science.gov (United States)

Gorski, Krzysztof M.; Silk, Joseph; Vittorio, Nicola

1992-01-01

A new technique is used to compute the correlation function for large-angle cosmic microwave background anisotropies resulting from both the space and time variations in the gravitational potential in flat, vacuum-dominated, cold dark matter cosmological models. Such models with Omega sub 0 of about 0.2, fit the excess power, relative to the standard cold dark matter model, observed in the large-scale galaxy distribution and allow a high value for the Hubble constant. The low order multipoles and quadrupole anisotropy that are potentially observable by COBE and other ongoing experiments should definitively test these models.

Engineering, Manufacture and Preliminary Testing of the ITER Toroidal Field (TF) Magnet Helium Cold Circulator

Science.gov (United States)

Rista, P. E. C.; Shull, J.; Sargent, S.

2015-12-01

The ITER cryodistribution system provides the supercritical Helium (SHe) forced flow cooling to the magnet system using cold circulators. The cold circulators are located in each of five separate auxiliary cold boxes planned for use in the facility. Barber-Nichols Inc. has been awarded a contract from ITER-India for engineering, manufacture and testing of the Toroidal Field (TF) Magnet Helium Cold Circulator. The cold circulator will be extensively tested at Barber-Nichols’ facility prior to delivery for qualification testing at the Japan Atomic Energy Agency's (JAEA) test facility at Naka, Japan. The TF Cold Circulator integrates features and technical requirements which Barber-Nichols has utilized when supplying helium cold circulators worldwide over a period of 35 years. Features include a vacuum-jacketed hermetically sealed design with a very low helium leak rate, a heat shield for use with both nitrogen & helium cold sources, a broad operating range with a guaranteed isentropic efficiency over 70%, and impeller design features for high efficiency. The cold circulator will be designed to meet MTBM of 17,500 hours and MTBF of 36,000 hours. Vibration and speed monitoring are integrated into a compact package on the rotating assembly with operation and health monitoring in a multi-drop PROFIBUS communication environment using an electrical cabinet with critical features and full local and network PLC interface and control. For the testing in Japan and eventual installation in Europe, the cold circulator must be certified to the Japanese High Pressure Gas Safety Act (JHPGSA) and CE marked in compliance with the European Pressure Equipment Directive (PED) including Essential Safety Requirements (ESR). The test methodology utilized at Barber-Nichols’ facility and the resulting test data, validating the high efficiency of the TF Cold Circulator across a broad operating range, are important features of this paper.

Engineering, Manufacture and Preliminary Testing of the ITER Toroidal Field (TF) Magnet Helium Cold Circulator

International Nuclear Information System (INIS)

C Rista, P E; Shull, J; Sargent, S

2015-01-01

The ITER cryodistribution system provides the supercritical Helium (SHe) forced flow cooling to the magnet system using cold circulators. The cold circulators are located in each of five separate auxiliary cold boxes planned for use in the facility. Barber-Nichols Inc. has been awarded a contract from ITER-India for engineering, manufacture and testing of the Toroidal Field (TF) Magnet Helium Cold Circulator. The cold circulator will be extensively tested at Barber-Nichols’ facility prior to delivery for qualification testing at the Japan Atomic Energy Agency's (JAEA) test facility at Naka, Japan. The TF Cold Circulator integrates features and technical requirements which Barber-Nichols has utilized when supplying helium cold circulators worldwide over a period of 35 years. Features include a vacuum-jacketed hermetically sealed design with a very low helium leak rate, a heat shield for use with both nitrogen and helium cold sources, a broad operating range with a guaranteed isentropic efficiency over 70%, and impeller design features for high efficiency. The cold circulator will be designed to meet MTBM of 17,500 hours and MTBF of 36,000 hours. Vibration and speed monitoring are integrated into a compact package on the rotating assembly with operation and health monitoring in a multi-drop PROFIBUS communication environment using an electrical cabinet with critical features and full local and network PLC interface and control. For the testing in Japan and eventual installation in Europe, the cold circulator must be certified to the Japanese High Pressure Gas Safety Act (JHPGSA) and CE marked in compliance with the European Pressure Equipment Directive (PED) including Essential Safety Requirements (ESR). The test methodology utilized at Barber-Nichols’ facility and the resulting test data, validating the high efficiency of the TF Cold Circulator across a broad operating range, are important features of this paper. (paper)

Two-dimensional mathematical model for simulation of the drying process of thick layers of natural materials in a conveyor-belt dryer

Directory of Open Access Journals (Sweden)

Salemović Duško R.

2017-01-01

Full Text Available This paper presents the mathematical model and numerical analysis of the convective drying process of thick slices of colloidal capillary-porous materials slowly moving through conveyor-belt dryer. A flow of hot moist air was used as drying agent. The drying process has been analyzed in the form of a 2-D mathematical model, in two directions: along the conveyor and perpendicular on it. The mathematical model consists of two non-linear differential equations and one equation with a transcendent character and it is based on the mathematical model developed for drying process in a form of a 1-D thin layer. The appropriate boundary conditions were introduced. The presented model is suitable for the automated control of conveyor-belt dryers. The obtained results with analysis could be useful in predicting the drying kinetics of potato slices and similar natural products.

Microstructural evaluation of Ti-35Nb-7,5 T alloy deformed by cold rolling and annealed

International Nuclear Information System (INIS)

Giudice, M.L.C.; Hayama, A.O.F.; Button, S.T.; Caram, R.

2010-01-01

This work presents the main results of microstructural characterization of Ti- 35Nb-7.5Ta (% in weight) deformed by cold rolling and annealed. Samples were obtained by electric arc melting, heat treated at 1000 deg C for 8 hours and water quenched. Samples were deformed by cold rolling in multiple passes up to a maximum reduction of 84%. Deformed samples were encapsulated in quartz under vacuum and annealed at 600, 700 e 800 deg C, in variable times and water quenched. Characterization was carried out using light optical microscopy, X-ray diffraction, Vickers hardness test and acoustic emission measurements to determine the Young's modulus. The results show the orientation occurrence of the martensitic phase in relation to the cold rolling direction in deformed samples. In samples annealed at 600 deg C recovery is predominant and samples annealed at 800 deg C for 60 min are fully recrystallized. (author)

Cold atoms as a coolant for levitated optomechanical systems

Science.gov (United States)

Ranjit, Gambhir; Montoya, Cris; Geraci, Andrew A.

2015-01-01

Optically trapped dielectric objects are well suited for reaching the quantum regime of their center-of-mass motion in an ultrahigh-vacuum environment. We show that ground-state cooling of an optically trapped nanosphere is achievable when starting at room temperature, by sympathetic cooling of a cold-atomic gas optically coupled to the nanoparticle. Unlike cavity cooling in the resolved-sideband limit, this system requires only a modest cavity finesse and it allows the cooling to be turned off, permitting subsequent observation of strongly coupled dynamics between the atoms and sphere. Nanospheres cooled to their quantum ground state could have applications in quantum information science or in precision sensing.

High flux isotope reactor cold source preconceptual design study report

International Nuclear Information System (INIS)

Selby, D.L.; Bucholz, J.A.; Burnette, S.E.

1995-12-01

In February 1995, the deputy director of Oak Ridge National Laboratory (ORNL) formed a group to examine the need for upgrades to the High Flux Isotope Reactor (HFIR) system in light of the cancellation of the Advanced Neutron Source Project. One of the major findings of this study was that there was an immediate need for the installation of a cold neutron source facility in the HFIR complex. The anticipated cold source will consist of a cryogenic LH 2 moderator plug, a cryogenic pump system, a refrigerator that uses helium gas as a refrigerant, a heat exchanger to interface the refrigerant with the hydrogen loop, liquid hydrogen transfer lines, a gas handling system that includes vacuum lines, and an instrumentation and control system to provide constant system status monitoring and to maintain system stability. The scope of this project includes the development, design, safety analysis, procurement/fabrication, testing, and installation of all of the components necessary to produce a working cold source within an existing HFIR beam tube. This project will also include those activities necessary to transport the cold neutron beam to the front face of the present HFIR beam room. The cold source project has been divided into four phases: (1) preconceptual, (2) conceptual design and research and development (R and D), (3) detailed design and procurement, and (4) installation and operation. This report marks the conclusion of the preconceptual phase and establishes the concept feasibility. The information presented includes the project scope, the preliminary design requirements, the preliminary cost and schedule, the preliminary performance data, and an outline of the various plans for completing the project

Evidence for hydrogen-assisted recovery of cold-worked palladium: hydrogen solubility and mechanical properties studies

Directory of Open Access Journals (Sweden)

Maria Ferrer

2017-07-01

Full Text Available The influence of hydrogen as an agent to accelerate the thermal recovery of cold-worked palladium has been investigated. The techniques used to characterize the effects of hydrogen on the thermal recovery of palladium were hydrogen solubility and mechanical property measurements. Results show that the presence of modest amounts of hydrogen during annealing of cold-worked palladium does enhance the degree of thermal recovery, with a direct correlation between the amount of hydrogen during annealing and the degree of recovery. The results indicate that the damage resulting from cold-working palladium can be more effectively and efficiently reversed by suitable heat treatments in the presence of appropriate amounts of hydrogen, as compared to heat treatment in vacuum. The somewhat novel technique of using changes in the hydrogen solubility of palladium as an indicator of thermal recovery has been validated and complements the more traditional technique of mechanical property measurements.

Assessment of the environmental microbiological cross contamination following hand drying with paper hand towels or an air blade dryer.

Science.gov (United States)

Margas, E; Maguire, E; Berland, C R; Welander, F; Holah, J T

2013-08-01

This study compared the potential for cross contamination of the surrounding environment resulting from two different hand-drying methods: paper towels and the use of an air blade dryer. One hundred volunteers for each method washed their hands and dried them using one of the two methods. Bacterial contamination of the surrounding environment was measured using settle plates placed on the floor in a grid pattern, air sampling and surface swabs. Both drying methods produced ballistic droplets in the immediate vicinity of the hand-drying process. The air blade dryer produced a larger number of droplets which were dispersed over a larger area. Settle plates showed increased microbial contamination in the grid squares which were affected by ballistic droplets. Using the settle plates counts, it was estimated that approx. 1.7 × 10(5) cfu more micro-organisms were left on the laboratory floor (total area approx. 17.15 m(2)) after 100 volunteers used an air blade dryer compared to when paper towels were used. The two drying methods led to different patterns of ballistic droplets and levels of microbial contamination under heavy use conditions. Whilst the increase in microbial levels in the environment is not significant if only nonpathogenic micro-organisms are spread, it may increase the risk of pathogen contamination of the environment when pathogens are occasionally present on people's hands. The study suggests that the risk of cross contamination from the washroom users to the environment and subsequent users should be considered when choosing a hand-drying method. The data could potentially give guidance following the selection of drying methods on implementing measures to minimise the risk of cross contamination. © 2013 The Society for Applied Microbiology.

Influence of Gap Distance on Vacuum Arc Characteristics of Cup Type AMF Electrode in Vacuum Interrupters

International Nuclear Information System (INIS)

Cheng Shaoyong; Xiu Shixin; Wang Jimei; Shen Zhengchao

2006-01-01

The greenhouse effect of SF 6 is a great concern today. The development of high voltage vacuum circuit breakers becomes more important. The vacuum circuit breaker has minimum pollution to the environment. The vacuum interrupter is the key part of a vacuum circuit breaker. The interrupting characteristics in vacuum and arc-controlling technique are the main problems to be solved for a longer gap distance in developing high voltage vacuum interrupters. To understand the vacuum arc characteristics and provide effective technique to control vacuum arc in a long gap distance, the arc mode transition of a cup-type axial magnetic field electrode is observed by a high-speed charge coupled device (CCD) video camera under different gap distances while the arc voltage and arc current are recorded. The controlling ability of the axial magnetic field on vacuum arc obviously decreases when the gap distance is longer than 40 mm. The noise components and mean value of the arc voltage significantly increase. The effective method for controlling the vacuum arc characteristics is provided by long gap distances based on the test results. The test results can be used as a reference to develop high voltage and large capacity vacuum interrupters

Vacuum-assisted delivery

Science.gov (United States)

... medlineplus.gov/ency/patientinstructions/000514.htm Vacuum-assisted delivery To use the sharing features on this page, ... through the birth canal. When is Vacuum-assisted Delivery Needed? Even after your cervix is fully dilated ( ...

Performance Analysis of Solar Assisted Fluidized Bed Dryer Integrated Biomass Furnace with and without Heat Pump for Drying of Paddy

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performances of a solar assisted fluidized bed dryer integrated biomass furnace (SA-FBDIBF and a solar assisted heat pump fluidized bed dryer integrated biomass furnace (SAHP-FBDIBF for drying of paddy have been evaluated, and also drying kinetics of paddy were determined. The SA-FBDIBF and the SAHP-FBDIBF were used to dry paddy from 11 kg with moisture content of 32.85% db to moisture content of 16.29% db (14% wb under an air mass flow rate of 0.1037 kg/s within 29.73 minutes and 22.95 minutes, with average temperatures and relative humidities of 80.3°C and 80.9°C and 12.28% and 8.14%, respectively. The average drying rate, specific energy consumption, and specific moisture extraction rate were 0.043 kg/minute and 0.050 kg/minute, 5.454 kWh/kg and 4.763 kWh/kg, and 0.204 kg/kWh and 0.241 kg/kWh for SA-FBDIBF and SAHP-FBDIBF, respectively. In SA-FBDIBF and SAHP-FBDIBF, the dryer thermal efficiencies were average values of 12.28% and 15.44%; in addition, the pickup efficiencies were 33.55% and 43.84% on average, whereas the average solar and biomass fractions were 10.9% and 10.6% and 36.6% and 30.4% for SA-FBDIBF and SAHP-FBDIBF, respectively. The drying of paddy occurred in the falling rate period. The experimental dimensionless moisture content data were fitted to three mathematical models. Page’s model was found best to describe the drying behaviour of paddy.

The Effect of Temperature and Drying Method on Drying Time and Color Quality of Mint

Directory of Open Access Journals (Sweden)

H Bahmanpour

2017-10-01

Full Text Available Introduction Mint (Mentha spicata L. cbelongs to the Lamiaceae family, is an herbaceous, perennial, aromatic and medicinal plant that cultivated for its essential oils and spices. Since the essential oil is extracted from dried plant, choosing the appropriate drying method is essential for gaining high quality essential oil.Vacuum drying technology is an alternative to conventional drying methods and reported by many authors as an efficient method for improving the drying quality especially color characteristics. On the other side, solar dryers are also useful for saving time and energy. In this study the effect of two method of dryings including vacuum-infrared versus solar at three different conventional temperatures (30, 40 and 50°C on mint plant is evaluated while factorial experiment with randomized complete block is applied. Drying time as well as color characteristics areconsidered for evaluation of each method of drying. Materials and Methods Factorial experiment with randomized complete block was applied in order to evaluate the effect of drying methods (vacuum-infrared versus solar and temperature (30, 40 and 50°C on drying time and color characteristics of mint. The initially moisture content of mint leaves measured according to the standard ASABE S358.2 during 24 hours inside an oven at 104 °C. Drying the samples continued until the moisture content (which real time measured reached to 10% wet basis. The components of a vacuum dryer consisted of a cylindrical vacuum chamber (0.335 m3 and a vacuum pump (piston version. The temperature of the chamber was controlled using three infrared bulbs using on-off controller. Temperature and weight of the products registered real time using a data acquisition system. The components of a solar dryer were consisting of a solar collector and a temperature control system which was turning the exhaust fan on and off in order to maintain the specific temperature. A date acquisition system was

Energy and exergy analyses of native cassava starch drying in a tray dryer

International Nuclear Information System (INIS)

Aviara, Ndubisi A.; Onuoha, Lovelyn N.; Falola, Oluwakemi E.; Igbeka, Joseph C.

2014-01-01

Energy and exergy analyses of native cassava starch drying in a tray dryer were carried out to assess the performance of the system in terms of energy utilization, energy utilization ratio, energy efficiency, exergy inflow and outflow, exergy loss and exegetic efficiency. The results indicated that for the starch with ash content of 0.76%, 0.85% crude protein, 0.16% crude fat, negligible amount of fiber, average granule size of 14.1 μm, pH of 5.88, amylose content of 23.45% and degree of crystallinity of 22.34%, energy utilization and energy utilization ratio increased from 1.93 to 5.51 J/s and 0.65 to 0.6 as the drying temperature increased from 40 to 60 °C. Energy efficiency increased from 16.036 to 30.645%, while exergy inflow, outflow and losses increased from 0.399 to 2.686, 0.055 to 0.555 and 0.344 to 2.131 J/s respectively in the above temperature range. Exergetic efficiency increased with increase in both drying air temperature and energy utilization and was lower than energy efficiency. Exergetic improvement potential also increased with increase in drying air temperature. Model equations that could be used to express the energy and exergy parameters as a function of drying temperature were established. - Highlights: • Energy and exergy analyses of cassava starch drying in a tray dryer were carried out. • Energy utilization increased with drying temperature. • Energy efficiency was higher than exergy efficiency. • Energy and exergy efficiencies increased with increase in temperature. • Improvement potential increased with increase in temperature

Experimental investigation of an indirect solar dryer integrated with phase change material for drying valeriana jatamansi (medicinal herb

Directory of Open Access Journals (Sweden)

A.K. Bhardwaj

2017-09-01

Full Text Available In this study, an experimental investigation of an indirect solar dryer integrated with phase change material has been carried out for drying Valeriana Jatamansi. The experimentation has been performed under the climatic conditions of Himalayan region, Solan (latitude − 30.91°N, longitude − 77.09°E, Himachal Pradesh (India in the month of October-November 2016. Paraffin RT-42 has been used as a phase change material in the dryer. Using this system, the moisture content of rhizomes reduced from 89% to 9% in 5 days as compared to heat pump drying and shade drying, which took 8 days and 14 days, respectively. Results of present study infer that the drying time using phase change material in this setup has reduced by 37.50% and 64.29% when compared to heat pump drying and shade drying, respectively. The dried rhizomes obtained are of superior quality in terms of colour, texture, aroma and bio-medical constituents. Analyses show that by using present setup, total valepotriates obtained were 3.47% as compared to traditional shade drying which yield 3.31%.

Vacuum phase transition solves the H0 tension

Science.gov (United States)

Di Valentino, Eleonora; Linder, Eric V.; Melchiorri, Alessandro

2018-02-01

Taking the Planck cosmic microwave background data and the more direct Hubble constant measurement data as unaffected by systematic offsets, the values of the Hubble constant H0 interpreted within the Λ CDM cosmological constant and cold dark matter cosmological model are in ˜3.3 σ tension. We show that the Parker vacuum metamorphosis (VM) model, physically motivated by quantum gravitational effects and with the same number of parameters as Λ CDM , can remove the H0 tension and can give an improved fit to data (up to a mean Δ χ2=-7.5 ). It also ameliorates tensions with weak lensing data and the high redshift Lyman alpha forest data. Considering Bayesian evidence, we found in the case of the Planck data set alone positive evidence for a VM model against a cosmological constant both in the six- and nine-parameter framework. When the R16 data set is also considered, we found a strong evidence for the VM model against a cosmological constant in nine-parameter space. We separately consider a scale-dependent scaling of the gravitational lensing amplitude, such as provided by modified gravity, neutrino mass, or cold dark energy, motivated by the somewhat different cosmological parameter estimates for low and high CMB multipoles. We find that no such scale dependence is preferred.

How cold is cold dark matter?

International Nuclear Information System (INIS)

Armendariz-Picon, Cristian; Neelakanta, Jayanth T.

2014-01-01

If cold dark matter consists of particles, these must be non-interacting and non-relativistic by definition. In most cold dark matter models however, dark matter particles inherit a non-vanishing velocity dispersion from interactions in the early universe, a velocity that redshifts with cosmic expansion but certainly remains non-zero. In this article, we place model-independent constraints on the dark matter temperature to mass ratio, whose square root determines the dark matter velocity dispersion. We only assume that dark matter particles decoupled kinetically while non-relativistic, when galactic scales had not entered the horizon yet, and that their momentum distribution has been Maxwellian since that time. Under these assumptions, using cosmic microwave background and matter power spectrum observations, we place upper limits on the temperature to mass ratio of cold dark matter today (away from collapsed structures). These limits imply that the present cold dark matter velocity dispersion has to be smaller than 54 m/s. Cold dark matter has to be quite cold, indeed

CFD Analysis to Calculate the Optimal Air Velocity in Drying Green Tea Process Using Fluidized Bed Dryer

Science.gov (United States)

Yohana, Eflita; Nugraha, Afif Prasetya; Diana, Ade Eva; Mahawan, Ilham; Nugroho, Sri

2018-02-01

Tea processing is basically distinguished into three types which black tea, green tea, and oolong tea. Green tea is processed by heating and drying the leaves. Green tea factories in Indonesia are generally using the process of drying by panning the leaves. It is more recommended to use the fluidization process to speed up the drying process as the quality of the tea can be maintained. Bubbling fluidization is expected to occur in this research. It is a process of bubbles are formed in the fluidization. The effectiveness of the drying process in a fluidized bed dryer machine needs to be improved by using a CFD simulation method to proof that umf < u < ut, where the average velocity value is limited by the minimum and the maximum velocity of the calculation the experimental data. The minimum and the maximum velocity value of the fluidization is 0.96 m/s and 8.2 m/s. The result of the simulation obtained that the average velocity of the upper bed part is 1.81 m/s. From the results obtained, it can be concluded that the calculation and the simulation data is in accordance with the condition of bubbling fluidization in fluidized bed dryer.

Transient analysis of the new Cold Source at the FRM-II

International Nuclear Information System (INIS)

Gutsmiedl, E.; Posselt, H.; Scheuer, A.

2003-01-01

The new Cold Source (CNS) at the FRM-II research reactor is completely installed. This paper reports on the results of the transient analysis in the design status for this facility for producing cold neutrons for neutron experiments, the implementation of the results in the design of the mechanical components, the measurements at the cold tests and the comparison with the data of the transient analysis. The important load cases are fixed in the system description and the design data sheet of the CNS. A transient analysis was done with the computer program ESATAN, the nodal configuration was identical with the planned system of the CNS and the boundary conditions were chosen so, that conservative results can be expected. The following transients of the load cases in the piping system behind the inpile part 1) normal storage of D 2 at the hydride storage vessel 2) breakdown of cooling system of the CNS and transfer of D 2 to the buffer tank 3) rapid charge of D 2 to the buffer tank with break of the insulation vacuum and flooding of Neon 4) reloading of the D 2 from the buffer tank to the D 2 hydride storage vessel were calculated. Additionally the temperature distribution for these transients in the connecting flanges of the systems to the inpile part were analysed. The temperature distributions in the flange region were take into account for the strength calculation of the flange construction. The chosen construction shows allowable values and a leak tight flange connection for the load cases. The piping system was designed to the lowest expected temperatures. The load cases in the moderator tank were take into account in the stress analysis and the fatigue analysis of the vacuum vessel and the moderator vessel. The results shows allowable stresses. The results shows that a transient analysis is necessary and helpful for good design of the CNS. (author)

Cold Antimatter Plasmas, and Aspirations for Cold Antihydrogen

Science.gov (United States)

2002-06-24

UNCLASSIFIED Defense Technical Information Center Compilation Part Notice ADP012494 TITLE: Cold Antimatter Plasmas, and Aspirations for Cold...part numbers comprise the compilation report: ADP012489 thru ADP012577 UNCLASSIFIED Cold Antimatter Plasmas, and Aspirations for Cold Antihydrogen G...and positrons. The antiprotons come initially from the new Antiproton Decel- erator facility at CERN. Good control of such cold antimatter plasmas is

Low-cycle fatigue behavior of oxygen-free high-conductivity copper at 3000C in high vacuum

International Nuclear Information System (INIS)

Liu, K.C.; Loring, C.M. Jr.

1983-01-01

In-vacuum fatigue tests were performed on commercially-pure OFHC copper and 35% Au-65% Cu brazing filler metal at 300 0 C. Excessive recrystallization due to exposure in the 1025 0 C brazing temperature cycle was detrimental to the fatigue life of the base metal; cold work was beneficial to the fatigue resistance. Triple-point cracking and grain boundary sliding were the prevailing modes of fatigue failure observed in the full-size specimens. However, a mixed morphology of ductile and cleavage-like fracture was observed on the fracture surface of the subsize specimen in which the grain structure appeared to have undergone a change because of the presence of surface cold work. The braze has superior fatigue resistance, but to exploit the maximum strength, the brazed joint must be devoid of defects such as cavities and cracks

Building solar dryer of tropical woods; Construccion de un secador solar de maderas tropicales

Energy Technology Data Exchange (ETDEWEB)

Hernandez R, J; Flores M, F. E; Cuevas D, O [Universidad de Quintana Roo, Chetumal, Quintana Roo (Mexico); Tolentino E, G [LABINTHAP-SEPI-ESIME-IPN, Mexico, D.F. (Mexico)

2000-07-01

In Quintana Roo, Mexico, several species of wood are used for handicrafts. The most commonly method used in the communities nearby Chetumal is natural drying, with the disadvantage of low quality in their products because the moisture contains in the wood. In this project studied the design of solar dryer for tropical woods in Quintana Roo. [Spanish] En este trabajo, se parte del analisis de las condiciones climatologicas existentes en el estado de Quintana Roo, Mexico, asi como de las necesidades de madera seca de una comunidad, como parametros basicos para el diseno y construccion de un secador solar de maderas tropicales.

Design and performance of a Nafion dryer for continuous operation at CO2 and CH4 air monitoring sites

Directory of Open Access Journals (Sweden)

L. R. Welp

2013-05-01

Full Text Available In preparation for routine deployment in a network of greenhouse gas monitoring stations, we have designed and tested a simple method for drying ambient air to near or below 0.2% (2000 ppm mole fraction H2O using a Nafion dryer. The inlet system was designed for use with cavity ring-down spectrometer (CRDS analyzers such as the Picarro model G2301 that measure H2O in addition to their principal analytes, in this case CO2 and CH4. These analyzers report dry-gas mixing ratios without drying the sample by measuring H2O mixing ratio at the same frequency as the main analytes, and then correcting for the dilution and peak broadening effects of H2O on the mixing ratios of the other analytes measured in moist air. However, it is difficult to accurately validate the water vapor correction in the field. By substantially lowering the amount of H2O in the sample, uncertainties in the applied water vapor corrections can be reduced by an order of magnitude or more, thus eliminating the need to determine instrument-specific water vapor correction coefficients and to verify the stability over time. Our Nafion drying inlet system takes advantage of the extra capacity of the analyzer pump to redirect 30% of the dry gas exiting the Nafion to the outer shell side of the dryer and has no consumables. We tested the Nafion dryer against a cryotrap (−97 °C method for removing H2O and found that in wet-air tests, the Nafion reduces the CO2 dry-gas mixing ratios of the sample gas by as much as 0.1 ± 0.01 ppm due to leakage across the membrane. The effect on CH4 was smaller and varied within ± 0.2 ppb, with an approximate uncertainty of 0.1 ppb. The Nafion-induced CO2 bias is partially offset by sending the dry reference gases through the Nafion dryer as well. The residual bias due to the impact of moisture differences between sample and reference gas on the permeation through the Nafion was approximately −0.05 ppm for CO2 and varied within ± 0.2 ppb for CH4. The

Control of pouring molten charge out of a levitation type cold crucible; Fuyogata cold crucible kara no hiyukaibutsu no chuto seigyo

Energy Technology Data Exchange (ETDEWEB)

Ando, K.; Iwai, K.; Asai, S. [Nagoya University, Nagoya (Japan). Faculty of Engineering

1994-10-25

The cold crucible is a high-frequency induced heating melting process consisting of the cold copper crucible, coil, and charge. The levitation type crucible is of the cup type device, with the magnetic field concentrated to the vicinity of the hole in its bottom, so that the whole charge is melted and non-contact retention is achieved by the Lorentz`s force. However, when the vacuum suction method or the tilting method is used to take out or pour a charge from the crucible, defects such as contamination due to contact with the wall and heat transfer are unavoidable. This report proposes a new pouring method using the electromagnetic force, providing the logical and experimental examinations. As a result of analysis of the electromagnetic force applied on the side of the charge levitating in the crucible, it was confirmed that changing the current value through the coil varies the pouring phenomenon, depending on the followability of the levitating position, and changing the relative position of the coil to the crucible enables pouring. Thus, the pouring form measuring method was established. 9 refs., 10 figs., 1 tab.

Vacuum considerations: summary

International Nuclear Information System (INIS)

Blechschmidt, D.; Halama, H.J.

1978-01-01

A summary is given of the efforts of a vacuum systems study group of the workshop on a Heavy Ion Demonstration Experiment (HIDE) for heavy ion fusion. An inadequate knowledge of cross-sections prevents a more concrete vacuum system design. Experiments leading to trustworthy numbers for charge exchange, stripping and capture cross-sections are badly needed and should start as soon as possible. In linacs, beam loss will be almost directly proportional to the pressure inside the tanks. The tanks should, therefore, be built in such a way that they can be baked-out in situ to improve their vacuum, especially if the cross-sections turn out to be higher than anticipated. Using standard UHV techniques and existing pumps, an even lower pressure can be achieved. The vacuum system design for circular machines will be very difficult, and in some cases, beyond the present state-of-the-art

Thermophysical Properties of Cold and Vacuum Plasma Sprayed Cu-Cr-X Alloys, NiAl and NiCrAlY Coatings. Part 2; Specific Heat Capacity

Science.gov (United States)

Raj, S. V.

2017-01-01

Part I of the paper discussed the temperature dependencies of the electrical resistivities, thermal conductivities, thermal diffusivities and total hemispherical emissivities of several vacuum plasma sprayed (VPS) and cold sprayed copper alloy monolithic coatings, VPS NiAl, VPS NiCrAlY, extruded GRCop-84 and as-cast Cu-17(wt.%)Cr-5%Al. Part II discusses the temperature dependencies of the constant pressure specific heat capacities, CP, of these coatings. The data were empirically were regression-fitted with the equation: CP = AT4 + BT3 + CT2 + DT +E where T is the absolute temperature and A, B, C, D and E are regression constants. The temperature dependencies of the molar enthalpy, molar entropy and Gibbs molar free energy determined from experimental values of molar specific heat capacity are reported. Calculated values of CP using the Neumann-Kopp (NK) rule were in poor agreement with experimental data. Instead, a modification of the Neumann-Kopp rule was found to predict values closer to the experimental data with an absolute deviation less than 6.5%. The specific molar heat capacities for all the alloys did not agree with the Dulong-Petit law, and CP is greater than 3R, where R is the universal gas constant, were measured for all the alloys except NiAl for which CP is less than 3R at all temperatures.

Contact discontinuities in a cold collision-free two-beam plasma

International Nuclear Information System (INIS)

Kirkland, K.B.; Sonnerup, B.U.O.

1982-01-01

A contact discontinuity in a collision-free magnetized plasma is a thin layer, possessing a nontrivial magnetic structure, across which no net plasma flow takes place (#betta#/sub n/ = 0) even though the magnetic field has a nonvanishing component (B/sub n/not =0) normal to it. This paper examines the structure of such discontinuities in a simple plasma model consisting of two oppositely directed cold ion beams and a background of cold massless electrons such that exact charge neutrality is maintained so that the electric field Eequivalent0. The basic equations describing self-consistent equilibria are developed for the more general situation where a net flow across the layer takes place (#betta#/sub n/ = 0) and where the magnetic field has two nonzero tangential components B/sub y/ and B/sub z/ but where E remains zero. These equations are then specialized to the case eta/sub n/equivalent0, B/sub z/equivalent0, and four different classes of sheets are obtained, all having thickness of the order of the ion inertial length: (1) layers separating two identical plasma and magnetic field regions. (2) an infinite array of parallel layers producing an undulated magnetic field, (3) layers containing trapped ions in closed orbits which separate two vacuum regions with uniform identical magnetic fields, and (4) layers which reflect a single plasma beam, leaving a vacuum with a revesed and compressed tangential field on the other side. Solutions for which #betta#/sub n/ = 0 but B/sub z/not =0 may also exist but have not been analyzed; rotational discontinuities are shown not to be possible in this model

CryoCart Restoration and Vacuum Pipe Construction

Science.gov (United States)

Chaidez, Mariana

2016-01-01

Propulsion systems that utilize hypergolic propellants have been used to power space vehicles since the beginning of the space program. Liquid methane and oxygen propulsion systems have emerged as an alternative and have proven to be more environmentally friendly. The incorporation of liquid methane/liquid oxygen (LOX) into the propulsion system has demonstrated an increase in engine performance, as well as a reduction in the volume, size and complexity of the system. Consequently, reducing the total mass of the vehicle which is a crucial aspect that is considered when planning space missions to both the Moon and Mars [1]. Project Morpheus has made significant advancements in liquid oxygen/liquid methane propulsion system technologies by incorporating a LOX/methane propulsion system to a vertical test bed. The vehicle consisted of a 5,000 lb main engine and four 20 lb remote control system (RCS) engines that utilize liquid methane/LOX as its propellant [1]. The vehicle completed successful flight testing at Kennedy Space Center in 2014 which marked the completion of the Morpheus project. Subsequent projects utilizing Morpheus' vertical test bed have been developed to make further advancements. One of the subsequent projects consisted of the addition of a smaller 2,000 lb main engine and a cold helium heat exchanger which would make it possible for a pressurant tank systems to be send to Mars or the Moon by significantly decreasing the overall mass and volume of the pressurant tank. The hot fire tests of the integrated system with the smaller main engine and cold helium heat exchanger were successful at sea level, but further studies are being conducted to better understand how the vertical test bed will behave under thermal-vacuum conditions. For this reason, the integrated vehicle will be taken to Plum Brook to be tested in a chamber capable of simulating these conditions. To ensure that the vehicle will function properly under vacuum conditions, testing will be

Hypothermic general cold adaptation induced by local cold acclimation.

Science.gov (United States)

Savourey, G; Barnavol, B; Caravel, J P; Feuerstein, C; Bittel, J H

1996-01-01

To study relationships between local cold adaptation of the lower limbs and general cold adaptation, eight subjects were submitted both to a cold foot test (CFT, 5 degrees C water immersion, 5 min) and to a whole-body standard cold air test (SCAT, 1 degree C, 2 h, nude at rest) before and after a local cold acclimation (LCA) of the lower limbs effected by repeated cold water immersions. The LCA induced a local cold adaptation confirmed by higher skin temperatures of the lower limbs during CFT and a hypothermic insulative general cold adaptation (decreased rectal temperature and mean skin temperature P adaptation was related to the habituation process confirmed by decreased plasma concentrations of noradrenaline (NA) during LCA (P general cold adaptation was unrelated either to local cold adaptation or to the habituation process, because an increased NA during SCAT after LCA (P syndrome" occurring during LCA.

Modern vacuum physics

CERN Document Server

Chambers, Austin

2005-01-01

Modern Vacuum Physics presents the principles and practices of vacuum science and technology along with a number of applications in research and industrial production. The first half of the book builds a foundation in gases and vapors under rarefied conditions, The second half presents examples of the analysis of representative systems and describes some of the exciting developments in which vacuum plays an important role. The final chapter addresses practical matters, such as materials, components, and leak detection. Throughout the book, the author''s explanations are presented in terms of first principles and basic physics, augmented by illustrative worked examples and numerous figures.

Gravitation and vacuum field

International Nuclear Information System (INIS)

Tevikyan, R.V.

1986-01-01

This paper presents equations that describe particles with spins s = 0, 1/2, 1 completely and which also describe 2s + 2 limiting fields as E → ∞. It is shown that the ordinary Hilbert-Einstein action for the gravitation field must be augmented by the action for the Bose vacuum field. This means that one must introduce in the gravitational equations a cosmological term proportional to the square of the strength of the Bose vacuum field. It is shown that the theory of gravitation describes three realities: matter, field, and vacuum field. A new form of matter--the vacuum field--is introduced into field theory

Surge-damping vacuum valve

International Nuclear Information System (INIS)