WorldWideScience

Sample records for coke coking waste

  1. New process of co-coking of waste plastics and blend coal

    Energy Technology Data Exchange (ETDEWEB)

    Liao, H.; Yu, G.; Zhao, P. (and others) [Shougang Technical Research Institute, Beijing (China)

    2006-07-01

    To recycle and reuse waste plastics, as well as to get a new resource of coking, co-coking process of waste plastics and blend coal has been developed by Nippon Steel. However, the ratio of waste plastics in blend coal should be limited in the range of 1% to maintain the coke strength. This paper suggested a new process of co-coking of waste plastics and blend coal. The new process can add the waste plastics ratio up to 2-4%; when the waste plastics ratio is 2%, the coke strength after reaction with CO{sub 2} (CSR) increased 8%. 8 refs., 2 figs., 3 tabs.

  2. The combustion characteristics of refuse derived fuels using coke/waste tire

    Energy Technology Data Exchange (ETDEWEB)

    Park, M.H. [Dep. of Mechanical Eng., Samcheok Nat' l Univ., Samcheok (Korea); Shin, D.Y. [Research Center for Advanced Mineral Aggregate Composite Products, Kangwon Nat' l Univ., Chuncheon (Korea)

    2005-07-01

    Today every nation faces serious problems of energy supply. Reasonable technologies to make use of coal (including coke) can not only help the mining-related economy which is showing a downward trend but also may fit in with the governmental energy policy. In this research, we aim to supply heating systems in factories, homes, and farms with a substitute fuel by developing coke/waste tire compound fuel with high efficiency for rational use of energy and for recycling of industrial products. A coke/waste boiler was used for this experiment, and different kinds of fuel were experimented including coke, waste tire, coke/waste A and coke/waste B. Four kinds of exhaust gas were also sampled by a gas analyzer, including CO, CO{sub 2}, NO and NO{sub 2} at different temperatures. (orig.)

  3. Coke production in large coke ovens

    Energy Technology Data Exchange (ETDEWEB)

    Zhuravskii, A.A.; Sytenko, I.V.; Zhupraner, Z.S.; Vasil' ev, Yu.S.; Karpukhin, E.A.; Pliner, G.E.; Rud' , A.I.; Bulyga, N.I. (NPO Koksokhimiya (USSR))

    1990-08-01

    Analyzes operation of the No 9 battery with coke ovens with a volume of 41.6 m{sup 3}. Factors that influence coke oven operation and coke quality are analyzed. The following problems are evaluated: composition of coal mixtures (G, Zh, K, OS, GZh coal types), methods for coal mixture preparation (crushing degree, selective crushing), temperature distribution in a coke oven and effects of heating system, coke shrinkage during coking and factors that influence shrinkage, optimizing pressure used for coke pushing, chemical, mechanical and physical properties of coke. Regression equations used for forecasting coke properties are derived: the M10 coke wear index, M25 coke strength index, ash content etc. Recommendations for optimum coking conditions are made. 6 refs.

  4. Full scale treatment of phenolic coke coking waste water under unsteady conditions

    Energy Technology Data Exchange (ETDEWEB)

    Suschka, Jan [Institute for Ecology of Industrial Areas, Katowice (Poland); Morel, Jacek; Mierzwinski, Stanislaw; Januszek, Ryszard [Coke Plant Przyjazn, Dabrowa Gornicza (Poland)

    1994-12-31

    Phenolic waste water from the largest coke coking plant in Poland is treated at a full technical scale. From the very beginning it became evident that very high qualitative variations in short and long periods were to be expected. For this purpose, the biological treatment plant based on activated sludge is protected through preliminary physical-chemical treatment and the results are secured by a final chemical stage of treatment. Nevertheless, improvements in the performance of the treatment plant have been found necessary to introduce. In this work, the experience gained over the last five years is described and developed improvements were presented. 3 refs., 9 figs., 1 tab.

  5. Full scale treatment of phenolic coke coking waste water under unsteady conditions

    Energy Technology Data Exchange (ETDEWEB)

    Suschka, Jan [Institute for Ecology of Industrial Areas, Katowice (Poland); Morel, Jacek; Mierzwinski, Stanislaw; Januszek, Ryszard [Coke Plant Przyjazn, Dabrowa Gornicza (Poland)

    1993-12-31

    Phenolic waste water from the largest coke coking plant in Poland is treated at a full technical scale. From the very beginning it became evident that very high qualitative variations in short and long periods were to be expected. For this purpose, the biological treatment plant based on activated sludge is protected through preliminary physical-chemical treatment and the results are secured by a final chemical stage of treatment. Nevertheless, improvements in the performance of the treatment plant have been found necessary to introduce. In this work, the experience gained over the last five years is described and developed improvements were presented. 3 refs., 9 figs., 1 tab.

  6. Bio-coke as an alternative to petroleum coke and metallurgical coke; Bio-cokes als alternatief voor petroleumcokes en metallurgische cokes

    Energy Technology Data Exchange (ETDEWEB)

    Croezen, H.J.; Van Lieshout, M. [CE Delft, Delft (Netherlands); Sevenster, M.N. [Sevenster Environmental Consultancy, Australian Capital Territory ACT (Australia)

    2012-11-15

    In the framework of elaborating the Dutch Roadmap Chemistry 2030), CE Delft has conducted an exploratory study for the Association of the Dutch Chemical Industry (VNCI) on the options of replacing (petroleum) coke in the chemical sector by biocokes. Coke is used as a reducing agent and/or raw material in four companies in the Dutch chemical industry (Tronox, ESD-SIC, Thermphos, Aluchemie). Replacing coke at these four companies can potentially yield a direct CO2 reduction of expectedly several hundreds of kilotons per year. For a first exploration of the options of bio-coke, CE Delft first conducted a desk study to get information on the quality and production costs for bio-coke. Subsequently, CE Delft had contact with the four chemical companies and a made a number of company visits. Moreover, the technical, economic and organizational capabilities, constraints and requirements with regard to a possible (partial) switch to biocokes have been explored. Based on the information available so far it can be concluded that biocokes seems to be a technically and economically interesting innovation. For implementation to finally take place, it is necessary to gain better insight in the technical and economic potential [Dutch] In verband met de uitwerking van de Routekaart Chemie 2030 heeft CE Delft voor VNCI een verkenning uitgevoerd naar de mogelijkheden voor vervanging van (petroleum)cokes in de chemische sector door biocokes. Cokes wordt gebruikt als reductiemiddel en/of grondstof bij een viertal bedrijven in de Nederlandse chemie (Tronox, ESD-SIC, Thermphos, Aluchemie). Het vervangen van cokes bij deze vier bedrijven kan in potentie een directe CO2-reductie van naar verwachting enkele honderden kilotonnen/jaar opleveren. Voor een eerste verkenning van de mogelijkheden van bio-cokes heeft CE Delft eerst een bureaustudie uitgevoerd naar informatie over kwaliteit van en productiekosten voor bio-cokes. Vervolgens heeft CE Delft contact gehad met de vier chemische

  7. Adsorption performance and mechanism in binding of Reactive Red 4 by coke waste

    International Nuclear Information System (INIS)

    Won, Sung Wook; Wu Guiping; Ma Hui; Liu Qiong; Yan Yao; Cui Longzhe; Liu Chengfu; Yun, Yeoung-Sang

    2006-01-01

    The protonated coke waste was used as a new type of adsorbent for the removal of Reactive Red 4. To identify the binding sites in the protonated coke waste, the waste was potentiometrically titrated. As a result, four types of functional groups were present in the waste, which was confirmed by FT-IR analysis. Among functional groups, primary amine groups (-NH 2 ) were likely the binding sites for anionic Reactive Red 4. It was also found that sulfonate, carboxyl and phosphonate groups played a role in electrostatic interference with the binding of dye molecules. The maximum adsorption capacities of the coke waste were 70.3 ± 11.1 and 24.9 ± 1.8 mg/g at pH 1 and 2, respectively. Kinetic study showed a pseudo-first-order rate of adsorption with respect to the solution. The uptake of Reactive Red 4 was not significantly affected by the high concentration of salts. These results of adsorption performance indicate the coke waste as a potentially economical adsorbent for dye removal

  8. Alternative coke production from unconventional feedstocks

    Energy Technology Data Exchange (ETDEWEB)

    Smoot, D.; Eatough, C.N.; Heaton, J.S.; Eatough, S.R.; Miller, A.B. [Combustion Resources, Provo, UT (US)

    2004-07-01

    This presentation reports on US Department of Energy and company sponsored research and development to develop a technology and process for making metallurgical-quality coke from alternate feedstocks, including by-product and waste carbonaceous materials. The basic patent-pending process blends and presses these carbon-containing materials into briquettes of specified size. This product is referred to as CR Clean Coke because pollutant emission levels are carefully controlled to low levels with little or no vagrant emissions during processing. A wide range of feedstock materials has been investigated in over 600 tests for run-of-mine and waste coal fines of various rank with blends of coal tars and pitches, coal and biomass chars, met-coke breeze or petroleum coke. For various coal/pet-coke/tar feedstocks, CR has produced uniform-sized briquettes in commercial-scale briquettes in three nominal sizes: one inch, two inch, and three inch. These products have been successfully qualified according to stringent requirements for conventional met-coke use in a blast furnace. Several formulation have met and frequently exceeded these established met-coke specifications. One specific product containing coal, tar and pet-coke was selected as a base formulation for which preliminary process design and cost estimates have been completed for construction and operation of a demonstration plant capable of producing 120,000 tons per year of CR Clean Coke. Plant design elements and blast furnace test plans are presented. Tailoring of CR Clean Coke products to other prospective end users including foundry, sugar, soda ash, and ferrometals industries presents additional opportunities. The text is accompanied by 30 slides/overheads. 14 refs., 3 figs., 9 tabs.

  9. The mechanism of coking pressure generation I: Effect of high volatile matter coking coal, semi-anthracite and coke breeze on coking pressure and plastic coal layer permeability

    Energy Technology Data Exchange (ETDEWEB)

    Seiji Nomura; Merrick Mahoney; Koichi Fukuda; Kenji Kato; Anthony Le Bas; Sid McGuire [Nippon Steel Corporation, Chiba (Japan). Environment and Process Technology Center

    2010-07-15

    One of the most important aspects of the cokemaking process is to control and restrain the coking pressure since excessive coking pressure tends to lead to operational problems and oven wall damage. Therefore, in order to understand the mechanism of coking pressure generation, the permeability of the plastic coal layer and the coking pressure for the same single coal and the same blended coal were measured and the relationship between them was investigated. Then the 'inert' (pressure modifier) effect of organic additives such as high volatile matter coking coal, semi-anthracite and coke breeze was studied. The coking pressure peak for box charging with more uniform bulk density distribution was higher than that for top charging. It was found that the coking pressure peaks measured at different institutions (NSC and BHPBilliton) by box charging are nearly the same. The addition of high volatile matter coking coal, semi-anthracite and coke breeze to a low volatile matter, high coking pressure coal greatly increased the plastic layer permeability in laboratory experiments and correspondingly decreased the coking pressure. It was found that, high volatile matter coking coal decreases the coking pressure more than semi-anthracite at the same plastic coal layer permeability, which indicates that the coking pressure depends not only on plastic coal layer permeability but also on other factors. Coking pressure is also affected by the contraction behavior of the coke layer near the oven walls and a large contraction decreases the coal bulk density in the oven center and hence the internal gas pressure in the plastic layer. The effect of contraction on coking pressure needs to be investigated further. 33 refs., 18 figs., 5 tabs.

  10. Programmed heating of coke ovens for increased coke size

    Energy Technology Data Exchange (ETDEWEB)

    Jenkins, D.R.; Mahoney, M.R. [University of Newcastle, Callaghan, NSW (Australia)

    2010-11-15

    Large, uniform sized coke is desirable for blast furnace use. It has previously been shown that the coke oven flue temperature in the first few hours of coking is a key determinant of coke size. In this paper, the authors present a new programmed heating approach, which is called pulsed heating, aiming to increase coke mean size at a given average flue temperature. The approach takes into account the charging sequence in coke oven batteries and the authors demonstrate how existing operating practice can be modified in batteries with suitable heating systems to achieve the desired heating programme. A mathematical model of fissure formation provides a prediction of the increase in coke mean size using pulsed heating, compared with standard heating. Pilot scale experiments have also been performed to validate the modelling approach. The results of the modelling indicate that the mean coke size can be increased by several millimetres in some cases, although results from the pilot scale show that pulsed heating increases coke size, but by a smaller amount than that predicted by the model. The potential advantages and limitations of pulsed heating are discussed, as well as opportunities for further investigation of the approach.

  11. The mechanism of coking pressure generation II: Effect of high volatile matter coking coal, semi-anthracite and coke breeze on coking pressure and contraction

    Energy Technology Data Exchange (ETDEWEB)

    Merrick Mahoney; Seiji Nomura; Koichi Fukuda; Kenji Kato; Anthony Le Bas; David R. Jenkins; Sid McGuire [BHP Billiton Technology, Shortland, NSW (Australia)

    2010-07-15

    One of the most important aspects of the cokemaking process is to control and limit the coking pressure since excessive coking pressure can lead to operational problems and oven wall damage. Following on from a previous paper on plastic layer permeability we have studied the effect of contraction of semi-coke on coking pressure and the effect of organic additives on contraction. A link between contraction (or simulated contraction) outside the plastic layer and coking pressure was demonstrated. The interaction between this contraction, local bulk density around the plastic layer and the dependence of the permeability of the plastic layer on bulk density was discussed as possible mechanisms for the generation of coking pressure. The effect of blending either a high volatile matter coal or one of two semi-anthracites with low volatile matter, high coking pressure coals on the coking pressure of the binary blends has been explained using this mechanism. 25 refs., 10 figs., 4 tabs.

  12. The coke dilemma

    Energy Technology Data Exchange (ETDEWEB)

    Champagne, P E; Lewis, J A

    1989-08-01

    Coke-making capacity reductions and the current status of coke oven batteries in the USA are surveyed, as well as prior forecasts of the steel and coke markets. The future position is then analysed and it is concluded that the US coke supply situation should improve up to 1995, but that there could be major domestic coke production deficits in the period 1996-2000; critical decisions will soon have to be made about replacement of coking capacity.

  13. Design and construction of coke battery 1A at Radlin coke plant, Poland

    Energy Technology Data Exchange (ETDEWEB)

    A.M. Kravchenko; D.P. Yarmoshik; V.B. Kamenyuka; G.E. Kos' kova; N.I. Shkol' naya; V.V. Derevich; A.S. Grankin [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    In the design and construction of coke battery 1A at Radlin coke plant (Poland), coking of rammed coke with a stationary system was employed for the first time. The coke batteries are grouped in blocks. Safety railings are provided on the coke and machine sides of the maintenance areas.

  14. Method of determining coking temperature of coke. [Experimental method of determining final coking temperature using a small sample and calibration graph

    Energy Technology Data Exchange (ETDEWEB)

    Mel' nichuk, A.Yu.; Bondarenko, A.K.; Fialkov, B.S.; Khegay, L.U.; Khvan, L.A.; Muzyzhuk, V.D.; Zakharov, A.G.; Zelenskiy, V.P.

    1985-01-01

    The coking temperature of coke should be determined from the magnitude of the ionization current of the medium during heating (3/sup 0//min) of a coke sample (2 g, fraction < 0.2 mm) in an oxidation medium with air supply (1 1/min). The coking temperature is determined from the maximum magnitude of current using a graduated graph constructed during analysis of coke samples obtained with different final coking temperatures. The discrepancy between the established coking temperature and that defined from the proposed method is 8-19/sup 0/, and that defined from electrical resistance of coke is 26-43/sup 0/. In addition to high accuracy, this method reduces the time outlays for making the analysis.

  15. Dale Coke: Coke Farm

    OpenAIRE

    Farmer, Ellen

    2010-01-01

    Dale Coke grew up on an apricot orchard in California’s Santa Clara Valley. In 1976 he bought ten acres of farmland near Watsonville in Santa Cruz County but continued to work repairing fuel injection systems rather than farming at his new home. In 1981, a struggle with cancer inspired him to rethink his life and become an organic farmer. His neighbor, who had grown strawberries using pesticides and chemical fertilizers, asserted that strawberries could not be grown organically. Coke set out ...

  16. Hot testing of coke

    Energy Technology Data Exchange (ETDEWEB)

    Balon, I D

    1976-07-01

    Earlier investigations failed to take full account of the factors affecting coke behavior within the blast furnace. An apparatus was accordingly developed for testing coke, based on a cyclone furnace where the sample could be held in a flow of hot oxidizing gases, simulating conditions in the blast furnace hearth. The results are said to be suitable for comprehensive assessment of the coke, including abrasive strength and its rate of gasification in a flow of carbon dioxide. Coke of size 6-10 mm tested at 1,100/sup 0/C in an atmosphere of oxidizing gases close to those obtaining in the blast furnace hearth, indicated that destruction and total gasification of the coke occurs after 5 minutes for a weak coke and 8 minutes for strong coke, depending on the physico-chemical and physico-mechanical properties of the particular coke. When samples were treated for a fixed period (3 minutes), the amount of coke remaining, and the percentage over 6 mm varied between 22 and 40 and between 4 and 7 percent respectively.

  17. Fissure formation in coke. 3: Coke size distribution and statistical analysis

    Energy Technology Data Exchange (ETDEWEB)

    D.R. Jenkins; D.E. Shaw; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

    2010-07-15

    A model of coke stabilization, based on a fundamental model of fissuring during carbonisation is used to demonstrate the applicability of the fissuring model to actual coke size distributions. The results indicate that the degree of stabilization is important in determining the size distribution. A modified form of the Weibull distribution is shown to provide a better representation of the whole coke size distribution compared to the Rosin-Rammler distribution, which is generally only fitted to the lump coke. A statistical analysis of a large number of experiments in a pilot scale coke oven shows reasonably good prediction of the coke mean size, based on parameters related to blend rank, amount of low rank coal, fluidity and ash. However, the prediction of measures of the spread of the size distribution is more problematic. The fissuring model, the size distribution representation and the statistical analysis together provide a comprehensive capability for understanding and predicting the mean size and distribution of coke lumps produced during carbonisation. 12 refs., 16 figs., 4 tabs.

  18. Fine art of coking

    Energy Technology Data Exchange (ETDEWEB)

    Dresner, S.

    1984-01-01

    The art and science of coking are discussed. Coke is the solid carbon made from the heavy, viscous residue left after the more useful products such as gasoline and diesel fuel have been refined out of the crude oil. Fuel grade coke can be a substitute for steam coal in many applications. Low-sulfur fuel coke is used in blast furnaces for steelmaking. The operations of Conoco's refineries for producing coke is described.

  19. Closed-cycle process of coke-cooling water in delayed coking unit

    International Nuclear Information System (INIS)

    Zhou, P.; Bai, Z.S.; Yang, Q.; Ma, J.; Wang, H.L.

    2008-01-01

    Synthesized processes are commonly used to treat coke-cooling wastewater. These include cold coke-cut water, diluting coke-cooling water, adding chemical deodorization into oily water, high-speed centrifugal separation, de-oiling and deodorization by coke adsorption, and open nature cooling. However, because of water and volatile evaporation loss, it is not suitable to process high-sulphur heavy oil using open treatments. This paper proposed a closed-cycling process in order to solve the wastewater treatment problem. The process is based on the characteristics of coke-cooling water, such as rapid parametric variation, oil-water-coke emulsification and steam-water mixing. The paper discussed the material characteristics and general idea of the study. The process of closed-cycle separation and utilization process of coke-cooling water was presented along with a process flow diagram. Several applications were presented, including a picture of hydrocyclones for pollution separation and a picture of equipments of pollution separation and components regeneration. The results showed good effect had been achieved since the coke-cooling water system was put into production in 2004. The recycling ratios for the components of the coke-cooling water were 100 per cent, and air quality in the operating area reached the requirements of the national operating site circumstance and the health standards. Calibration results of the demonstration unit were presented. It was concluded that since the devices went into operation, the function of production has been normal and stable. The operation was simple, flexible, adjustable and reliable, with significant economic efficiency and environmental benefits. 10 refs., 2 tabs., 3 figs

  20. Fissure formation in coke. 2: Effect of heating rate, shrinkage and coke strength

    Energy Technology Data Exchange (ETDEWEB)

    D.R. Jenkins; M.R. Mahoney [CSIRO, North Ryde, NSW (Australia). Mathematical and Information Sciences

    2010-07-15

    We investigate the effects of the heating rate, coke shrinkage and coke breakage strength upon the fissure pattern developed in a coke oven charge during carbonisation. This is done principally using a mechanistic model of the formation of fissures, which considers them to be an array of equally spaced fissures, whose depth follows a 'period doubling' pattern based upon the time history of the fissures. The model results are compared with pilot scale coke oven experiments. The results show that the effect of heating rate on the fissure pattern is different to the effect of coke shrinkage, while the effect of coke breakage strength on the pattern is less pronounced. The results can be seen in both the shape and size of resulting coke lumps after stabilisation. The approach gives the opportunity to consider means of controlling the carbonisation process in order to tune the size of the coke lumps produced. 7 refs., 18 figs., 4 tabs.

  1. Mineral matter reactions in cokes

    Energy Technology Data Exchange (ETDEWEB)

    D. French; R. Sakurovs; M. Grigore [CSIRO Energy Technology (Australia)

    2009-07-15

    Some cokes appear to be particularly susceptible to weakening in the blast furnace. A mechanism which has been postulated to explain this is silica reduction by coke. Thus this project was initiated to ascertain the behaviour of quartz and silicates in coke with an emphasis on the role of the clay minerals. It is now possible to obtain quantitative mineralogical data and, the case of coal, to also obtain quantitative data on mineral grain size, shape and association through the use of automated electron beam image analysis techniques. This new ability can allow relationships between the amount of minerals in a coke and its reactivity to be established for the first time. Samples of five Australian coking coals were selected based upon quartz and clay mineral contents, mineral grain size and association. Samples were also provided by BlueScope Steel of coal, feed coke, and tuyere coke samples from the bosh, deadman and raceway regions of the blast furnace. The analytical work program conducted was as follows: Preparation of cokes by CSIRO; Petrography of starting coals and cokes; QEMSCAN of coals; LTA and XRD of starting coals and cokes; Coke reactivity tests (NSC and small scale); Petrography, LTA and XRD of reacted cokes; Petrographic and XRD examination of heat treated cokes. This study indicates that the NSC reactivity test does not adequately reflect the behaviour of coke in the lower part of the blast furnace. Further investigation of the behaviour of coke in the lower part of the blast furnace is required.

  2. Gasification of oil sand coke: review

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E. [IMAF Group, Ottawa, ON (Canada)

    1998-08-01

    The production of synthetic crude from the tar sands in Western Canada has been steadily increasing. Most of the delayed coke produced by Suncor is combusted on site, whereas all fluid coke produced by Syncrude is stockpiled.The database on the chemical and physical properties of the oil sand coke, including the composition and fusion properties of the mineral matter, has been established. The reactivity of the coke was determined by oxygen chemisorption, fixed bed and fluid bed bench scale gasification and pilot plant gasification. The reactivity of the oil sand coke for gasification is rather low and comparable to high rank coals, such as anthracite. Slurrability tests revealed that a solid concentration in water, approaching 70 wt%, can be achieved. Gasification is the front runner among clean technologies for the conversion of carbonaceous solids to useful products. Several commercial gasifiers are available to cover the wide range of severity. Because of the low reactivity of oil sands coke, high severity conditions are required to achieve high gasification conversion. Such conditions can be attained in entrained bed gasifiers. Gasifiers employing both dry and slurry feeding systems are suitable. A high efficiency, low SO{sub x} and NO{sub x} emissions, as well as a low solid waste production are among the key advantages of the gasification technology compared with thecompeting technologies. Commercial gasification of oil sands coke is delayed because of the availability of natural gas on the site of the upgrading plants. Potential for the transportation of the oil sand coke to USA for electricity generation using the integrated gasification combined-cycle (IGCC) technology was evaluated. 27 refs., 17 figs., 9 tabs.

  3. Coke retorts

    Energy Technology Data Exchange (ETDEWEB)

    Jones, S; MacDonald, J D

    1916-07-15

    To charge vertical coke retorts while preventing escape of gases the coal is fed by a revolving drum to an archimedean screw at the base of the retort, the coke being discharged at the top through a water seal. The feed pockets of the drum which revolves between plates, deliver coal from the hopper to the revolving screw. The coke is forced under the hood to the water seal and is removed by rake conveyor, the gases escaping through the pipe to the main.

  4. 80. special meeting on coke

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    There were 12 papers presented at the special meeting on coke. These have the following headings: relationship between coal properties and optical anisotropic textures of coke; development of optical texture of chemically modified low rank coal; relationship between fluid and swelling properties of Akabira coal; estimation of coal fluidity; present state and future of robotics; on the thermal stress during the carbonisation process of coals; development of estimation model for coke porosity distribution in the coke oven using X-ray CT; carbonization reaction of coke oven; relationship between qualities of coke and width of coke oven; development of carbonization model in coke ovens - estimation of growing clearance between heating wall and charge; development of automatic transparency analyzer for activated sludge process.

  5. 46 CFR 148.04-15 - Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, uncalcined; petroleum coke, uncalcined and calcined (mixture). 148.04-15 Section 148.04-15 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... Requirements for Certain Material § 148.04-15 Petroleum coke, uncalcined; petroleum coke, uncalcined and...

  6. Coke

    Energy Technology Data Exchange (ETDEWEB)

    Trumble, M J

    1925-07-02

    Coke is obtained from coal, lignite, peat, or wood by heating the material in a retort and distilling off the volatiles by the passage of superheated steam or hot vapors, the hot porous residue being treated with a liquid hydrocarbon and the temperature being so maintained the latter is cracked and carbon deposited on the coke. The vapors or light oils are condensed and the incondensable gases are used as fuel.

  7. Producing metallurgic coke

    Energy Technology Data Exchange (ETDEWEB)

    Abe, T.; Isida, K.; Vada, Y.

    1982-11-18

    A mixture of power producing coals with coal briquets of varying composition is proposed for coking in horizontal chamber furnaces. The briquets are produced from petroleum coke, coal fines or semicoke, which make up less than 27 percent of the mixture to be briquetted and coals with a standard coking output of volatile substances and coals with high maximal Gizeler fluidity. The ratio of these coals in the mixture is 0.6 to 2.1 or 18 to 32 percent, respectively. Noncaking or poorly caking coals are used as the power producing coals. The hardness of the obtained coke is DJ15-30 = 90.5 to 92.7 percent.

  8. Pace studying worldwide coke production

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Pace Consultants Inc., Houston, has started a multiclient study of world-wide petroleum coke production, examining environmental initiatives and eventually forecasting prices of fuel grade coke. Pace expects coker expansions, increased operating severity, and reduced cycle times to boost coke supply to more than 50 million metric tons/year in 2000, compared with 39.7 million metric tons in 1992. Increased supply and tightened environmental rules in countries consuming large amounts of petroleum coke will be the main factors affecting coke markets. The paper discusses coke quality and the Japanese market

  9. Developing new technology of coal coking

    Energy Technology Data Exchange (ETDEWEB)

    Erkin, L.I.; Nefedov, P.Ya.

    1981-03-01

    This paper characterizes types of coke (grain size, compression strength, abrasion, porosity) used by: blast furnaces, shaft furnaces, ferroalloys and phosphorus production, and ore agglomeration. Development of formed metallurgical coke production on the basis of technologies worked out by the Eastern Research Scientific Institute for Coal Chemistry is analyzed. The following phases in the investigations are stressed: optimization of coal blends (increasing proportion of coals with poor caking properties, pressing briquets, carbonization, temperature distribution and temperature control, using heat emitted by hot coke for coal preheating (heat consumption of coking is reduced to 200 kcal/kg). On the basis of technology developed and tested by VUKhIN formed coke consisting of 60% G6 coal and 40% 2SS coal has been produced. Using the coke in blast furnaces increases furnace capacity by 5% and reduces coke consumption in a furnace by 2.6%. It is suggested that wide use of the proposed technology of formed metallurgical coke production in the Kuzbass (using coals with poor caking properties from surface mines) would increase coke production of the region to 50 Mt for a year. technology of producing formed foundry coke from: 80 to 86% anthracites, semianthracites and coals with poor caking properties, 5 to 10% coking coal, and 8% binder is evaluated. Formed foundry coke produced from the blend reduces coke consumption in a foundry by 25 to 30% and increases cast iron temperature by 20 to 50/sup 0/C. Technologies of producing coke for phosphorus industry by continuous coking of coals difficult to coke in vertical coke ovens and production of coke for ore agglomeration are also discussed. (In Russian)

  10. Relationship between coal and coke microstructure and the high temperature properties of coke. [Temperature dependence

    Energy Technology Data Exchange (ETDEWEB)

    Tsuyuguchi, K; Yamaji, M; Sugimoto, Y

    1980-02-01

    This paper considers the relationship of the properties of coke and parent coal with the high temperature properties, including reactivity, of coke. Aspects considered include coke texture and grade, and the optical reflectivity of coal and coke. (8 refs.) (In Japanese)

  11. Simulation of blast furnace operation during the substitution of coke and pulverized coal with granulated waste plastic

    Directory of Open Access Journals (Sweden)

    Kovačević Tihomir M.

    2014-01-01

    Full Text Available The possibility of using the waste plastic as reducing agent in blast furnace for obtaining pig iron is in focus for the past couple year. The simulation of blast furnace process in BFC software has been performed in order to analyze the coke and coals saving, CO2 emission and determining the economic benefits. Three different batches were made for comparative analysis, depending on the batch composition and input of batch components into the blast furnace: case 1 (C1, case 2 (C2 and case 3 (C3. The base case, C1 contains sinter (bulk material which is needed for obtaining 1 tone of pig iron, quartz which provides slag alkalinity and coke as reducing and energy agent. C2 has the same components as C1, but contains pulverized coal instead one part of coke and C3 contains granulated waste plastic instead coke in an approximately the same amount as pulverized coal. The substitution of coke with pulverized coal and waste plastic is 18.6 % and 25.2 %, respectively. The economic, productivity and ecologic aspects have been analyzed. The consumption of each tone of waste plastic in blast furnace saves 360 $, which is 18 times more than its price, bearing in mind that the market price of coke is 380 $/t % and waste plastic 20 $/t. Regarding the specific productivity, it decreases from 2.13 for C1 to 1.87 for C3. From an environmental aspect there are two main benefits: reduction of CO2 emission and impossibility of dioxin formation. The CO2 emission was 20.18, 19.46 and 17.21 for C1, C2 and C3, respectively.

  12. Solar thermochemical production of syngas from petroleum coke: feasibility study for injection of coke slurries

    International Nuclear Information System (INIS)

    Vidal, A.; Romero, M.; Kritter F; Steinfeld A

    2006-01-01

    The steam-gasification of pet-coke using concentrated solar radiation is proposed as a viable alternative to solar hydrogen production. Pet-coke is major solid byproduct from the processing of heavy and extra-heavy oils using delay-coking technology. This report summarizes the major accomplishments to develop a cheap and efficient feeding of petroleum coke by coke water slurries without the need of a carrier gas. The samples were Delayed coke of different grain sizes, in particular from 1,8 to 200 mm (as received). In order to analyse the flow properties of the slurries, some tests were conducted to measure the viscosity of the samples. Then, the pet-coke water slurries were injected into the reactor to study the gasification process. In these experiments, some operational parameters were: molar ratio from 2 to 3 (water/coke), temperature up to 1000 C, residence times from 5 to 9 s. In those conditions, the coke is converted primarily to CO, H 2 , CO 2 and small amounts of methane. Concentration of outlet gases of about 30-50 of H 2 ; 15-20 of CO, 10-15 CO 2 , 1-2% CH 4 were obtained with X coke ∼ 65 to 85%. (authors)

  13. Basic characteristics of new shape formed coke in burden distribution; Shingata seikei cokes no sonyu bunpu tokusei

    Energy Technology Data Exchange (ETDEWEB)

    Ichida, M; Yamamoto, T; Komaki, I; Oda, H; Matsunaga, S; Matsuzaki, S; Deno, T; Konno, N [Nippon Steel Corp., Tokyo (Japan)

    1996-12-01

    Basic characteristics in burden distribution and charging pattern of new shape formed coke developed in order to improve the properties of small size and low void fraction that pillow-type formed coke h s were conducted by 1/3 scale charging model and mathematical model of blast furnace. Basic characteristics, those are, inclination angle, coke-collapse and trajectory of new shape formed coke are almost the same as those of conventional coke. In the case of wall charging of new shape formed coke, until 60% of total charged coke, new shape formed coke is able to be charged without it`s rolling to the center. It is possible to apply RABIT model to new shape formed coke charging without it`s major modification. In the case of new shape formed coke wall charging, the fluctuation in furnace is supposed to be smaller than that in the case of pillow-type formed coke wall charging. Moreover, it`s center charging is supposed to be applied to actual blast furnace. More accurate estimation of in-furnace phenomena by mathematical model considering coke reactivity, is a subject to be worked out in future. 11 refs., 9 figs., 5 tabs.

  14. Cooperation with COMECON members in coke chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Medricky. Z

    1987-05-01

    Discusses activities of the coking industry division of the standing committee for iron metallurgy of the COMECON. The following cooperation fields are analyzed: raw material basis for coking industry, coal charge preparation and methods for reducing proportion of coking coal in a coal charge (heat treatments, formed coke processes, partial briquetting, pelletizing, increasing coking temperature, packing etc.), coking technology, coke quenching, screening, chemical processing of coal gas, environmental protection in the coking industry, environmental effects of coking, pitch coke production, methods for increasing labor productivity. Research programs coordinated by member countries are reviewed. Programs in which Czechoslovakia participates are discussed.

  15. Coking oven for continuous coke production

    Energy Technology Data Exchange (ETDEWEB)

    Vabrousek, R

    1979-07-15

    The coking oven has a vertical rectangular chamber with lateral heating walls to which heat exchangers are attached. The roof from the face of the chamber is a hermetic chute, whose vertical walls are connected to the lateral walls of the chamber and which has the feed conveyor with an unloading and evening device; to the upper wall of which a hermetic loading funnel for coal is attached and a lead-off for gas. The bottom of the chamber consists of segmented locks that are taken up by the hermetic chute. The chute's vertical walls are connected to the vertical walls of the chamber and its horizontal wall has a hermetic unloading funnel with a conveyor for coke removal. Height and width of the chamber are similar to standard chambers; their length reaches 100 to 200 m and longer. Length depends on coke preparation time and speed with which the unloading device can transfer coal. For normal operation, the conveyor belt must function properly in conjunction with the unloading device and segmented locks that form the bottom of the chamber.

  16. Results of tuyere coke sampling with regard to application of appropriate coke strength after reaction (CSR for a blast furnace

    Directory of Open Access Journals (Sweden)

    Shiau J-S.

    2017-01-01

    Full Text Available Raising pulverized coal injection (PCI will decrease coke rate, but increase the residence time of coke and abrasion in the blast furnace (BF. Thus, insufficient coke strength will generate more coke fines in the lower BF and result in lower permeability and production of hot metal (HM. For understanding the behavior of coke at various HM productivities, a tuyere coke sampler was used to collect the coke samples for measuring the coke strength. Firstly, the difference of sampled coke under the conditions of various HM productivities was explored. Secondly, the BF operating conditions and causes of generating more coke fines was correlated by testing the coke reaction rate after reaction. Finally, according to the above analysis results, the relative regression equations had been obtained for sampling coke properties, BF operation conditions and BF permeability. Furthermore, the coke strength after reaction (CSR quantitative target and its online system at various blast conditions were set to provide some reference for coke and HM production.

  17. Impact on surface water quality due to coke oven effluents

    International Nuclear Information System (INIS)

    Ghose, M.K.; Roy, S.

    1994-01-01

    Large quantities of water are used for the quenching of hot coke and also for washing the gas produced from the coke ovens. Liquid effluents thus generated are highly polluted and are being discharged into the river Damodar without proper treatment. Four coke plants of Bharat Coking Coal Ltd.(BCCL) have been surveyed for characterization and to assess the impact on surface water quality. About 175-200 kilolitres of waste water is being generated per day by each of the coke plants. The concentration of CO, BOD, COD, TSS, phenol and cyanide in each of the coke plants were found to exceed the limits specified by pollution control board. Ammonia, oil and grease and TDS were found to be 19.33 mg/l, 7.81 mg/l, 1027.75 mg/l respectively. Types of samples collected, sampling frequencies, sample preservation and the results obtained have been discussed. (author). 6 refs., 1 tab., 1 fig

  18. Substitutes for metallurgical coke in pyrometallurgical processes

    Energy Technology Data Exchange (ETDEWEB)

    Koshkarov, V.Ya.

    1982-08-01

    A briquetting process using sulphurous petroleum coke and a bituminous binder is described. The characteristics of briquettes made of petroleum coke, blends of coal and petroleum coke, and coal and metallurgical coke are compared. The prospect of replacing 25 to 50% of the metallurgical coke used in lime kilns with non-calcined petroleum coke briquettes is described. (4 refs.)

  19. Materials for making coke

    Energy Technology Data Exchange (ETDEWEB)

    Kern, L

    1936-08-19

    In the preparation of carbonized fuel briquettes, material such as bituminous, lignitic, or anthracitic coal, slack, waste or shale is treated with an electropositive solution such as hydrochloric acid or an acidic chloride to bring ash-forming constituents into colloidal form. The mixture is pressed with a colloid precipitating electro-negative solution such as sodium hydroxide, and moulded, the product being heated in the absence of air and coked. In an example bituminous coal is ground and then masticated with dilute hydrochloric acid. Some dilute manganese chloride is added followed by a solution of sodium hydroxide which precipitates the metals and silica as colloidal gels while the mixture is thoroughly agitated. The plastic mass is briquetted and dried at about 125/sup 0/C and then coked in vertical ovens at 700/sup 0/C. Chlorides recovered with the distillate gases may be utilized as solvent instead of hydrochloric acid. If the coal contains a large amount of sulfur acidified manganese chloride including a large proportion of iron is used as colloid forming material, the oxides of manganese and iron subsequently precipitated forming stable compounds with the non-volatile sulfur on coking or combustion.

  20. Coke briquets for metallurgy based on a thermoreactive binder

    Energy Technology Data Exchange (ETDEWEB)

    Tjutjunnikov, J.B.; Florinskij, V.N.; Orechov, V.N.; Nefedov, P.J.; Sasmurin, V.I.; Kirenskij, V.N. (Khar' kovskii Inzhenerno-Ehkonomicheskii Institut (USSR))

    1992-02-01

    Describes a process for production of briquets for metallurgy with binder and coke fines or anthracite. The suggested binder is waste phenol resin from the production of phenol (cumene method). Resin properties are given. Possible reaction mechanisms yielding solidified matter are discussed. The production process requires 10-15% binder and applies charge heating up to 200 C over 30 min. Catalytic amounts of sodium hydroxide or sulfuric acid were also employed. The production process is shown in a flowsheet. Properties of produced briquets are tabulated. The briquets were used in a 8 t/h cupola furnace and their performance was compared to that of KL-1 coke. Performance was found to be comparable; the cost of coke briquets was less than that of heating coke. 2 refs.

  1. Nitrogen Chemistry and Coke Transformation of FCC Coked Catalyst during the Regeneration Process

    Science.gov (United States)

    Shi, Junjun; Guan, Jianyu; Guo, Dawei; Zhang, Jiushun; France, Liam John; Wang, Lefu; Li, Xuehui

    2016-06-01

    Regeneration of the coked catalyst is an important process of fluid catalytic cracking (FCC) in petroleum refining, however, this process will emit environmentally harmful gases such as nitrogen and carbon oxides. Transformation of N and C containing compounds in industrial FCC coke under thermal decomposition was investigated via TPD and TPO to examine the evolved gaseous species and TGA, NMR and XPS to analyse the residual coke fraction. Two distinct regions of gas evolution are observed during TPD for the first time, and they arise from decomposition of aliphatic carbons and aromatic carbons. Three types of N species, pyrrolic N, pyridinic N and quaternary N are identified in the FCC coke, the former one is unstable and tends to be decomposed into pyridinic and quaternary N. Mechanisms of NO, CO and CO2 evolution during TPD are proposed and lattice oxygen is suggested to be an important oxygen resource. Regeneration process indicates that coke-C tends to preferentially oxidise compared with coke-N. Hence, new technology for promoting nitrogen-containing compounds conversion will benefit the in-situ reduction of NO by CO during FCC regeneration.

  2. PROSPECTS FOR COKE BREEZE RECOVERY

    Directory of Open Access Journals (Sweden)

    D. N. Mihnovets

    2012-01-01

    Full Text Available Researches give grounds to believe in the possibility of receiving briquettes from coke waste mixed with peat dry coal and their use for smelting iron in the cupola or as a household fuel.

  3. Experimental and numerical investigations of coke descending behavior in a coke dry quenching cooling shaft

    International Nuclear Information System (INIS)

    Feng Yanhui; Zhang Xinxin; Yu Quan; Shi Zhongyin; Liu Zhicheng; Zhang Hu; Liu Huafei

    2008-01-01

    A viscous flow model based on the Navier-Stokes equation is developed to describe coke descending behavior in the 1/7-scaled-down experimental setup of an actual 75 t/h cooling shaft. It is found that the internal friction due to cokes viscosity significantly influences the descending behavior of cokes in the lower part of the shaft, while the external wall friction dominates the sluggish flow of the cokes in the shaft. An asymptotic friction coefficient expression is proposed for granular mixtures flowing along the shaft wall modified from normal wall tress, and the concept of bulk solid viscosity is introduced to describe the internal friction between coke particles. The results simulated by the present model are compared with those by the potential flow and the kinematic model without friction. The viscous flow model is quite good to simulate the bulk coke flow as the physically important frictions are engaged

  4. Production of fine coke in a hearth-type furnace (Report on ECSC contract 7720-EB/108)

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    A balance was established for the hearth-type coking oven and waste heat boiler system. Tests concerning the operational safety showed that, in the case of breakdowns, the oven and waste heat boiler could be shut down without any danger. The quality of the brown coal fine coke produced, could be improved by optimizing the heights of the layer in the hearth-type, the degasification temperature of the oven, and the operation of the coke cooling system. Higher coking temperature caused a lower grain disintegration and lower abrasion rates. The range of size of coke production was enlarged to lump size by additional feeding of 2-inch briquettes to the coking oven.

  5. Determination of electrical resistivity of dry coke beds

    Energy Technology Data Exchange (ETDEWEB)

    Eidem, P.A.; Tangstad, M.; Bakken, J.A. [NTNU, Trondheim (Norway)

    2008-02-15

    The electrical resistivity of the coke bed is of great importance when producing FeMn, SiMn, and FeCr in a submerged arc furnace. In these processes, a coke bed is situated below and around the electrode tip and consists of metallurgical coke, slag, gas, and metal droplets. Since the basic mechanisms determining the electrical resistivity of a coke bed is not yet fully understood, this investigation is focused on the resistivity of dry coke beds consisting of different carbonaceous materials, i.e., coke beds containing no slag or metal. A method that reliably compares the electrical bulk resistivity of different metallurgical cokes at 1500{sup o} C to 1600{sup o}C is developed. The apparatus is dimensioned for industrial sized materials, and the electrical resistivity of anthracite, charcoal, petroleum coke, and metallurgical coke has been measured. The resistivity at high temperatures of the Magnitogorsk coke, which has the highest resistivity of the metallurgical cokes investigated, is twice the resistivity of the Corus coke, which has the lowest electrical resistivity. Zdzieszowice and SSAB coke sort in between with decreasing resistivities in the respective order. The electrical resistivity of anthracite, charcoal, and petroleum coke is generally higher than the resistivity of the metallurgical cokes, ranging from about two to about eight times the resistivity of the Corus coke at 1450{sup o}C. The general trend is that the bulk resistivity of carbon materials decreases with increasing temperature and increasing particle size.

  6. Scientific research in the area of coking and coking by-products (based on material from the All-Union Coordinating Conference)

    Energy Technology Data Exchange (ETDEWEB)

    Rydkevich, M.I.; Tselik, M.P.; Belkina, T.V.

    1985-06-01

    Subjects covered in the all-union coordinating conference on coking and chemical by-products of coking, which took place on 13-15 July 1984, are discussed. One hundred forty eight on-going and new research themes accepted as research projects for 1985-86 were discussed. Areas of research include coals from the eastern deposits and Pechora basin as raw materials for coking; coals from the southern deposits as coking raw materials; technology of coal preparation for coking; technology for producing blast furnace coke and methods of assessing its quality; technology for producing other kinds of coke and carbon graphite materials; methods for extraction processing and producing chemical products from coking.

  7. Coke quality requirements in POSCO

    Energy Technology Data Exchange (ETDEWEB)

    Song, J.; Yi, J.; Wang, H. [POSCO (Republic of Korea). Cokemaking Dept.

    2001-07-01

    The 26 overheads describes coke quality requirements in POSCO, Republic of Korea. It is concluded that it is necessary to develop new coal and to prompt technical development in order to produce high quality coke. To improve coke quality. Posco had applied DMAIC (define, measurement, analysis, improvement, control) technique which is part of Six-Sigma activity.

  8. Cocaine (Coke, Crack) Facts

    Science.gov (United States)

    ... That People Abuse » Cocaine (Coke, Crack) Facts Cocaine (Coke, Crack) Facts Listen Cocaine is a white ... 69 KB) "My life was built around getting cocaine and getting high." ©istock.com/ Marjot Stacey is ...

  9. Coke gasification costs, economics, and commercial applications

    International Nuclear Information System (INIS)

    Jahnke, F.C.; Falsetti, J.S.; Wilson, R.F.

    1996-01-01

    The disposition of petroleum coke remains a problem for modern high conversion refineries. Market uncertainty and the price for coke can prevent the implementation of otherwise attractive projects. The commercially proven Texaco Gasification Process remains an excellent option for clean, cost effective coke disposition as demonstrated by the new coke gasification units coming on-line and under design. Previous papers, have discussed the coke market and general economics of coke gasification. This paper updates the current market situation and economics, and provide more details on cost and performance based on recent studies for commercial plants

  10. The impact of liquid-liquid-vapour phase behaviour on coke formation from model coke precusors

    Energy Technology Data Exchange (ETDEWEB)

    Minicucci, D.; Shaw, J.M. [Univ. of Toronto, Dept. of Chemical Engineering and Applied Chemistry, Toronto, ON (Canada)

    2000-08-01

    Catalysts used in the hydroprocessing of heavy feedstocks deactivate due to coke deposition. Although the mechanism for coke formation is not fully understood, condensation reactions of polynuclear aromatic compounds present in the feeds are a key aspect. The effect of coke deposition on catalyst performance is typically modelled using accelerated aging agents comprising model coke precursors. Mixtures employed in such studies polynuclear aromatic compounds such as anthracene as the coke precursor, and long chain alkanes such as hexadecane as a diluent. We show in this paper that binary and pseudo binary mixtures of polynuclear aromatic compounds and n-alkanes present TYPE II, TYPE IV, or TYPE III phase behaviour according to the van Konynenburg and Scott (1980) phase projection nomenclature, Incubation periods and the apparent autocatalytic effects associated with coke deposition in such systems are explained through a combination of high temperature phase equilibrium experiments and computations with the model systems n-alkane + anthracene + hydrogen, n-alkane + pyrene + hydrogen, and n-alkane + dibenzo[a,k]chrysene + hydrogen. (au)

  11. Influence of rubber granulate in the coal blend on important process parameters of the coking plant

    Energy Technology Data Exchange (ETDEWEB)

    A. Winter; K. Pilz; A. Gahleitner; G. Woisetschlaeger; Monika Friedl [Voestalpine Stahl GmbH (Germany)

    2004-07-01

    The talk is outlined in a series of 14 slides/overheads. It discusses the use of scrapped tires in coking plant and traces the amount of zinc present in every product of the coking plant, blast furnaces and sintering plant - coke, coke breeze, sinter and waste water produced.

  12. Behavior of coke in large blast furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, N

    1978-01-01

    Three blast furnaces were quenched in operation and the contents were examined; the temperature distribution was also measured, using Tempil pellets. The furnaces examined included a low productivity one, which was examined to see what was wrong. Changes in the quality of coke as it descends in the furnace, and coke behavior in the raceway and hearth are reported. The functions required of coke, and the effects of poor coke quality, are explained, together with the coke quality required in large blast furnaces. A theoretical study of the role of coke in large blast furnaces is included.

  13. Utilization of HSC-ROSE residue as coking aid for the production of high quality coke from brown coal

    Energy Technology Data Exchange (ETDEWEB)

    Bohlmann, D.; Limmer, H.; Naundorf, W.; Hood, R.L.; Washimi, K. (VEB Petrolchemisches Kombinat, Schwedt (German Democratic Republic))

    1989-04-01

    Evaluates suitability of HSC-ROSE petroleum pitch as binder for production of brown coal coke. This pitch has been available in the GDR since installation in 1988 of a 750 kt/a HSC (high conversion soaker cracking) plant, which processes 360 C visbreaker residue from Soviet crude oil, and the building of a ROSE (residue oil supercritical reaction) plant. Laboratory as well as semi-industrial experiments were carried out at the Freiberg Academy, GDR on pulverizing, briquetting and coking various brown coal types with HSC-ROSE pitch. Briquetting and coking results are shown in tables. Experiments showed that the resulting coke has 124% higher compression strength and 100% higher abrasion strength than regular brown coal coke without HSC-ROSE binder. The high quality coke is adequate for use as metallurgical blast furnace coke. An economic assessment of modifying an existing brown coal coking plant to process 2 Mt/a brown coal with 10% pitch binder is made. Required investment amounts to 54 million US dollars, estimated annual profits based on 1987 prices are 19.5 million US dollars. 4 refs.

  14. A new method for manufacturing ICEM form coke and its coking in slanted furnaces. Part II. Obtaining ICEM form coke in slanted furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Barbu, I; Coposescu, V; Kost, J; Manolescu, A; Michailidis, N; Solceriu, R; Stoicoi, A

    1978-01-01

    An engineering scheme of the process is given, together with the characteristics of the chamber furnaces with an inclined hearth and the quality of the coke obtained in the industrial assembly at a gas factory. The assembly consists of 56 chamber furnaces with a volume up to 10 cubic meters. The height of the chambers is 4000 mm on one side and 4295 mm on the other with a length of 7500 mm and a width of 360-480 mm. The heating temperature is 1200/sup 0/, and the coking time is 22-24 hours. The annual production of the batteries for metallurgical coke is 90 thousand tons, and the average strength of the coke is M40-66.0; M10-15.51.

  15. Investigations concerning the mechanism of action of brown-coal coke particles in aerobic biological waste water treatment

    International Nuclear Information System (INIS)

    Rieger, W.

    1990-01-01

    At the start of this work experience with the use of brown coal coke in the activated sludge process was lacking entirely. It therefore was necessary to carry through preliminary experiments in order to practically test the effect of Grown-coal coke. In two technical-scale experiments and a pilot test, very good results were obtained with the application of brown-coal coke to activated sludge. These, and previously published results, permitted to evolve moodel concepts of the mechanism of action of coal, especially brown coal coke, in activated sludge. According to these concepts the coal particles act as buffers and a temporary adsorbent of oxygen and waste water constituents. This in turn stimulates the colonization of the surface with microorganisms. In order to corroborate these model concepts, the - adsorption and desorption of solved oxygen to coal in a watery medium and - the effect of coal over a longer period of time were investigated. The results in essence confirm the model concepts. (UWa) [de

  16. Research and development in production of special coke types

    Energy Technology Data Exchange (ETDEWEB)

    Nefedov, P.Ya.; Unterberger, O.G.; Strakhov, V.M. (Vostochnyi Nauchno-Issledovatel' skii Uglekhimicheskii Institut (USSR))

    1991-03-01

    Discusses methods for increasing quality of foundry coke and quality of special coke types used in non-ferrous metallurgy. Types of coal from various coal basins for production of foundry coke, types of petroleum and coal-derived additives improving caking and coking properties of the standard coal mixtures and effects of partial coal charge briquetting are discussed. Three types of partial coal charge briquetting are comparatively evaluated: continuous coking of the briquetted mixtures of weakly caking lean coal types, anthracites and coking coal mixed with thermosoftening binders; continuous coking of identical mixtures briquetted with non-thermosoftening binders; coking coke dust mixed with thermoreactive binders and briquetted at 200-300 C. Coking conditions, the final coking temperature, binder consumption rates, dimensions of coal briquets, ash content, sulfur content and coke mechanical properties (compression strength and wear) are comparatively evaluated.

  17. Production of blast furnace coke from soft brown coal

    Energy Technology Data Exchange (ETDEWEB)

    Scholz, G.; Wundes, H.; Schkommodau, F.; Zinke, H.-G. (VEB Gaskombinat Schwarze Pumpe (German Democratic Republic))

    1988-01-01

    Reviews experimental production and utilization of high quality brown coal coke in the GDR during 1985 and 1986. The technology of briquetting and coking brown coal dust is described; the superior parameters of produced coke quality are listed in comparison to those of regular industrial coke made from brown and black coal. Dust emission from high quality brown coal coke was suppressed by coke surface treatment with dispersion foam. About 4,200 t of this coke were employed in black coal coke substitution tests in a blast furnace. Substitution rate was 11%, blast furnace operation was positive, a substitution factor of 0.7 t black coal coke per 1 t of brown coal coke was calculated. Technology development of high quality brown coal coke production is regarded as complete; blast furnace coke utilization, however, requires further study. 8 refs.

  18. Numerical analysis of macro-crack formation behavior within the lump coke; Cokes sonai kiretsu shinten kiko no kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, H; Sato, H; Miura, T [Tohoku University, Sendai (Japan). Faculty of Engineering

    1995-03-15

    The thermal stress analysis within lump coke was studied in order to investigate macro-crack formation and deformation behavior which strongly influence heat and mass transfer in a coke oven chamber. The dilatation of plastic layer, heating rate dependence of thermophysical and mechanical properties of coal/coke, creep in the plastic and semi-coke layers, macro-crack propagation and radiative heat transfer within the macro-crack were considered in an analytical model. The macro-crack propagation was determined from the estimated crack tip stress intensity factor, K{sub I}, at the macro-crack tip compared with the plane strain fracture toughness, K{sub IC}, through the unsteady-state calculation. Calculated results on crack formation and deformation behavior of lump coke were in good agreement with experimental observations in a laboratory-scale oven chamber. The analytical model could predict micro-crack formation within the lump coke normal to the heated wall and the coke surface close to the heated wall. 12 refs., 13 figs.

  19. Reducibility mill scale industrial waste via coke breeze at 850-950ºC

    Directory of Open Access Journals (Sweden)

    Gaballah N.M.

    2015-01-01

    Full Text Available Mill scale is a very attractive industrial waste due to its elevated iron content (about = 69.33% Fe besides being suiTab. for direct recycling to the blast furnace via sintering plant. In this paper the characteristics of raw materials and the briquettes produced from this mill scale were studied by different methods of analyses. The produced briquettes were reduced with different amounts of coke breeze at varying temperatures, and the reduction kinetics was determined. The activation energy of this reaction ≈ 61.5 kJ/mole for reduction of mill scale with coke breeze in the form of briquettes with 2% molasses where the chemical reaction interface model is applicable.

  20. Coking of residue hydroprocessing catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Gray, M.R.; Zhao, Y.X. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical Engineering; McKnight, C.A. [Syncrude Canada Ltd., Edmonton, AB (Canada); Komar, D.A.; Carruthers, J.D. [Cytec Industries Inc., Stamford, CT (United States)

    1997-11-01

    One of the major causes of deactivation of Ni/Mo and Co/Mo sulfide catalysts for hydroprocessing of heavy petroleum and bitumen fractions is coke deposition. The composition and amount of coke deposited on residue hydroprocessing catalysts depends on the composition of the liquid phase of the reactor. In the Athabasca bitumen, the high molecular weight components encourage coke deposition at temperatures of 430 to 440 degrees C and at pressures of 10 to 20 MPa hydrogen pressure. A study was conducted to determine which components in the heavy residual oil fraction were responsible for coking of catalysts. Seven samples of Athabasca vacuum residue were prepared by supercritical fluid extraction with pentane before being placed in the reactor. Carbon content and hydrodesulfurization activity was measured. It was concluded that the deposition of coke depended on the presence of asphaltenes and not on other compositional variables such as content of nitrogen, aromatic carbon or vanadium.

  1. Coke, char and organic waste behaviour in the blast furnace with high injection rate

    Directory of Open Access Journals (Sweden)

    Gudenau, H. W.

    2003-10-01

    Full Text Available Blast furnace operation with low coke rate, high amount of auxiliary hydrocarbons and use of nut coke causes a change in coke quality requirements. In particular, not burned in the raceway residues of injected substances (char and ash can influence the coke behaviour. Therefore combustion efficiency of various organic wastes with and without pulverized coal injection (PCI and coal char has been investigated under the raceway simulation conditions. Mixing of various substances improves their combustion efficiency. Study on coke gasification by carbon dioxide in the presence of char showed that with the increase of char concentration, coke strength reduction becomes smaller. The reactivity of char with CO2 is higher than that of coke. Therefore char is consumed preferentially. In presence of injected char, total pore volume in coke and its wear resistance were increased. Coke reactivity and microstructure in the presence of various kinds of ash has been studied. Many ash spheres were observed on the surface of coke matrix and its size was dependent on ash properties.

    La operación del horno alto con una tasa baja de coque, una cantidad elevada de hidrocarburos auxiliares y el empleo de coque calibrado, origina un cambio en las necesidades de calidad del coque. En particular, pueden influir en el comportamiento del coque los residuos inquemados en el raceway (cavidad enfrente a las toberas del horno de las sustancias que se inyectan (char y cenizas. El char es el residuo de carbón que se origina después que el carbón libera sus sustancias volátiles. Por tanto, se ha investigado la eficiencia de la combustión de varios residuos orgánicos con y sin inyección de carbón pulverizado (ICP y char, bajo las condiciones de simulación del raceway. La mezcla de varias sustancias mejora la eficiencia a la combustión. El estudio de la gasificación del coque por el dióxido de carbono en la

  2. Petroleum coke as energy source: an update

    International Nuclear Information System (INIS)

    Pinelli, G.

    2008-01-01

    A previous review presented a critical evaluation of the use of petroleum coke as energy source. After some years, with reference to increased petroleum coke production, that paper is revised. In particular, the attention is now focused on world petroleum coke market trends and, in regard to petroleum coke used as fuel, on new Italian environment laws. [it

  3. Consumption of fuels and energy in the coking industry and ways of reducing consumption

    Energy Technology Data Exchange (ETDEWEB)

    Vasil' ev, Yu.S.; Tsel' ik, M.P.; Belkina, T.V. (Khar' kovskii Nauchno-Issledovatel' skii Uglekhimicheski Institut (USSR))

    1989-08-01

    Coking plants in the USSR consume 4,000 million kWh electric energy, 100 million GJ heat energy and 35,000 million m{sup 3} gaseous fuels per year. Structure of energy consumption is the following: 68% gaseous fuels, 24% steam and 8% electric energy. Processes of coal preparation, crushing, mixing, coking and quenching are analyzed from the point of view of energy consumption. The following methods for reducing energy consumption are discussed: using the FM-25 flotation machines for flotation of coking coal slurries, briquetting the whole coal charge for coking, optimization of air supply rates for combustion of gases used for coke oven heating, use of control systems for coke oven heating considering coal charge density, waste heat utilization from quenching. 4 refs.

  4. Coke from partially briquetted preheated coal mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Belitskii, A.N.; Sklyar, M.G.; Toryanik, Eh.I.; Bronshtein, A.P.

    1988-07-01

    Analyzes effects of partial coal charge briquetting on coking and on quality of coke for metallurgy. Effects of mixing hot coal briquets on temperature and moisture of coal were investigated on an experimental scale in a coking plant. Coal with a moisture content of 12% was used. Coking mixture consisted of 30% briquets and 70% crushed coal. Fifteen minutes after briquet mixing with coal, the mean coal charge temperature increased to 100-105 C and moisture content was lower than 2-5%. Results of laboratory investigations were verified by tests on a commercial scale. Experiments showed briquetting of weakly caking or non-caking coal charge components to be an efficient way of preventing coke quality decline. Adding 15-20% briquets consisting of weakly caking coal did not influence coke quality. Mixing hot coal briquets reduced moisture content in crushed coal, increased its temperature and reduced coking time.

  5. Dependence of microhardness of coke on carbon content and final coking temperature

    Energy Technology Data Exchange (ETDEWEB)

    Kaloc, M.; Dvorak, P.

    1995-12-31

    At present time is important the coke-quality, tested by various methods again. The new methods of evaluation of coke quality as e.g. CSR, CRI, ACRI etc. demonstrate, that the mechanical stability parameters are in connection of microstructure of coke mass. The purpose of present paper is to investigate the dependence of microhardness on the carbon content and the final carbonisation temperature in the coal-coke series. The samples prepared experimentally in more series from different coal blends from 20{degrees}C to 1100{degrees}C were investigated both mega- and microscopically. The tests of microhardness are based on the use of the Hanemann microhardness tester. Principally this method consists in impressing the diamond pyramid into the surface of the sample. The data on the pressure applied are subtracted on the scale of load. An important factor influencing the results is the choice of the points from which the sample is to be withdrawn. The choice is dependent on the aim to be achieved. For the determination of an average microhardness it is sufficient to take sample from the middle part of the coke block representing the half width of the coking chamber. The choice of the point is also of great importance. In strong and homogeneous walls, sharply bounded, impressions can be found with a distinct diagonal cross. In thin walls the impressions are distinguished by distinct boundaries, the middle part, however, not being distinct as the pyramidal point did not penetrate the wall. Impressions providing accurate values are those distinctly bounded by a distinct diagonal cross. The walls not having been chosen correctly, the errors reveal themselves as the scattering of the points in the diagrams of microhardness.

  6. Briquetting of Coke-Brown Coal Mixture

    Directory of Open Access Journals (Sweden)

    Ïurove Juraj

    1998-09-01

    Full Text Available The paper presents the results of the research of briquetting a coke-brown coal composite The operation consists of the feeding crushed coal and coke to moulds and pressing into briquettes which have been made in the Laboratories at the Mining Faculty of Technical University of Košice (Slovakia. In this research, all demands will be analyzed including the different aspects of the mechanical quality of briquettes, the proportion of fine pulverulent coal and coke in bricks, the requirements for briquetting the coke-brown coal materials.

  7. Making coke

    Energy Technology Data Exchange (ETDEWEB)

    Wodehouse-Temple, C G

    1929-07-12

    Semi-coke is produced by mixing low-value absorbent solid carbonaceous material such as coal dust, slack, gas-works coke, lignite, torbanite, raphilite, cannel, or shale with not more than 20% of a carbonaceous binding material such as petroleum distillation residue, tarry residues, pitch bitumen, Trinidad asphalt, Manjak or the substance known under the registered Trade Mark Gilsonite and subjecting the mixture without briquetting to a temperature not exceeding 550/sup 0/C. According to the first Provisional Specification, the mixture may if desired be briquetted before being heated and the second constituent may be present to the extent of 30%.

  8. REDUCING POWER PRODUCTION COSTS BY UTILIZING PETROLEUM COKE

    Energy Technology Data Exchange (ETDEWEB)

    Kevin C. Galbreath; Donald L. Toman; Christopher J. Zygarlicke

    1999-09-01

    Petroleum coke, a byproduct of the petroleum-refining process, is an attractive primary or supplemental fuel for power production primarily because of a progressive and predictable increase in the production volumes of petroleum coke (1, 2). Petroleum coke is most commonly blended with coal in proportions suitable to meet sulfur emission compliance. Petroleum coke is generally less reactive than coal; therefore, the cofiring of petroleum coke with coal typically improves ignition, flame stability, and carbon loss relative to the combustion of petroleum coke alone. Although petroleum coke is a desirable fuel for producing relatively inexpensive electrical power, concerns about the effects of petroleum coke blending on combustion and pollution control processes exist in the coal-fired utility industry (3). The Energy & Environmental Research Center (EERC) completed a 2-year technical assessment of petroleum coke as a supplemental fuel. A survey questionnaire was sent to seven electric utility companies that are currently cofiring coal and petroleum coke in an effort to solicit specific suggestions on research needs and fuel selections. An example of the letter and survey questionnaire is presented in Appendix A. Interest was expressed by most utilities in evaluating the effects of petroleum coke blending on grindability, combustion reactivity, fouling, slagging, and fly ash emissions control. Unexpectedly, concern over corrosion was not expressed by the utilities contacted. Although all seven utilities responded to the question, only two utilities, Northern States Power Company (NSP) and Ameren, sent fuels to the EERC for evaluation. Both utilities sent subbituminous coals from the Power River Basin and petroleum shot coke samples. Petroleum shot coke is produced unintentionally during operational upsets in the petroleum refining process. This report evaluates the effects of petroleum shot coke blending on grindability, fuel reactivity, fouling/slagging, and

  9. Gasification reactivities of cokes derived from Athabasca bitumen

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.

    1985-10-01

    Gasification reactivities of cokes obtained from Athabasca bitumen by delayed coking and fluid coking were compared in fixed and fluidized bed systems. In both systems the C + O/sub 2/ reaction accounted for the most of converted carbon. The C + H/sub 2/O reaction proceeded to a smaller extent. The bulk reactivity of the fluid coke was higher than that of delayed coke, when comparing -20 to +60 mesh particles in fluidized bed and -14 to +20 mesh particles in fixed bed, respectively. However, the reactivity of the delayed coke expressed per unit of surface area was markedly higher than that of the fluid coke. 9 figs., 7 tabs., 6 refs. (A.V.)

  10. Microwave-assisted grinding of metallurgical coke

    International Nuclear Information System (INIS)

    Ruisanchez, E.; Juarez-Perez, E. J.; Arenillas, A.; Bermudez, J. M.; Menendez, J. A.

    2014-01-01

    Metallurgical cokes are composed of graphitic carbon (s2p2) and different inorganic compounds with very different capacities to absorb microwave radiation. Moreover, due to the electric conductivity shown by the metallurgical cokes, microwave radiation produces electric arcs or microplasmas, which gives rise to hot spots. Therefore, when these cokes are irradiated with microwaves some parts of the particle experiment a rapid heating, while some others do not heat at all. As a result of the different expansion and stress caused by thermal the shock, small cracks and micro-fissures are produced in the particle. The weakening of the coke particles, and therefore an improvement of its grind ability, is produced. This paper studies the microwave-assisted grinding of metallurgical coke and evaluates the grinding improvement and energy saving. (Author)

  11. Power, cement industries shape coke future

    International Nuclear Information System (INIS)

    Swain, E.J.

    1991-01-01

    The production of petroleum coke by U.S. refineries is expected to continue to increase in the coming years. Process and market trends also indicate the likelihood of further increases in fuel-grade coke production. In this article, the properties and uses of the various grades of petroleum coke, as well as pricing and market trends, will be discussed

  12. Production of fine coke from brown coal

    Energy Technology Data Exchange (ETDEWEB)

    Koenigs, H B

    1977-08-01

    The coke supply of the iron and steel industry, the design, function, and special features of the open-hearth are described, including coking properties and applications of the culm coke produced from brown coal. (In German)

  13. The Bricoke process for producing metallurgical coke in conventional ovens from blends containing a high percentage of non-coking coal

    Energy Technology Data Exchange (ETDEWEB)

    Vidal, R; Munnix, K; Dellieu, J

    1980-06-01

    The article discusses the following aspects:- description of the BRICOKE process; trials in pilot plant, showing the influence of the different parameters on the coke quality and delimiting the range of the suitable non-coking coals; industrial scale trials of long term with 33% of non-coking coal briquettes in the charge; influence on the coking process as well as on the blast furnace working and increase of the output of usual coke-oven by the BRICOKE process. (11 refs.)

  14. Blast-furnace coke production in high capacity coke oven batteries from the viewpoint of domestic raw material resources

    Energy Technology Data Exchange (ETDEWEB)

    Krause, W

    1977-05-01

    The problem is treated in a complex manner taking into account such technological improvements as: oiling, drying, charge preheating, dry quenching of coke as well as mechanical processing of coke which taken together will give blast furnace coke of the highest quality from domestic coals.

  15. New designs in the reconstruction of coke-sorting systems

    Energy Technology Data Exchange (ETDEWEB)

    A.S. Larin; V.V. Demenko; V.L. Voitanik [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    In recent Giprokoks designs for the reconstruction of coke-sorting systems, high-productivity vibrational-inertial screens have been employed. This permits single-stage screening and reduction in capital and especially operating expenditures, without loss of coke quality. In two-stage screening, >80 mm coke (for foundry needs) is additionally separated, with significant improvement in quality of the metallurgical coke (25-80 mm). New designs for the reconstruction of coke-sorting systems employ mechanical treatment of the coke outside the furnace, which offers new scope for stabilization of coke quality and permits considerable improvement in mechanical strength and granulometric composition of the coke by mechanical crushing.

  16. Production of rubbly culm coke from lignite

    Energy Technology Data Exchange (ETDEWEB)

    Koenigs, H B [Rheinische Braunkohlenwerke A.G., Koeln (Germany, F.R.). Hauptabteilung Kohleverarbeitung; Kurtz, R [Rheinische Braunkohlenwerke A.G., Frechen (Germany, F.R.). Abt. Verkokung und Chemie

    1977-08-01

    The article deals with the coke supply of the iron and steel industry, the design, function, and special features of the open-hearth, and describes the coking properties and applications of the culm coke produced from lignite.

  17. Process of coke less without waste treatment of direct vanadium allowing steel melting

    International Nuclear Information System (INIS)

    Lisienko, V.G.; Droujinina, O.G.; Morozova, V.A.; Ladigina, N.V.; Yusfin, Yu.S.; Parenkev, A.E.

    2003-01-01

    The development of new methods of steel production are now conducted with the purpose of energy consumption and harmful emissions reduction. The choice of technology and equipment in this case plays a marginal role. It is well known that vanadium alloying steel has increased service properties. The known classical scheme of vanadium steel melting is very power-intensive, as includes such power-intensive processes as blast furnace process and chemical processing of vanadium slag therewith sintering and by-product coke processes are accompanied by significant harmful emissions. In so doing the vanadium losses may run to 60%. In view of requests of environment protection and economical efficiency the new process of coke less without wastes processing of vanadium-bearing raw material with direct vanadium allowing of steel - LP-process is developed. Its purpose is the melting on the basis of vanadium-bearing titanomagnetite of vanadium allowing steel with increase of vanadium concentration in steel and diminution of vanadium losses without application coke and natural gas with use of any coals and carbon-bearing wastes. LP-process consists of three aggregates and corresponding processes: process of liquid-phase reduction, process of vanadium-bearing pellets metallization in the shaft furnace, and process of alloying steel melting in the arc electric furnace. The obtained results have shown, that the LP-process is more energy saving on a comparison with other methods of vanadium allowing steel production. (Original)

  18. Young employees of the coking industry for technological progress

    Energy Technology Data Exchange (ETDEWEB)

    Ladyzhinskii, V.M.; Shul' ga, I.V.

    1986-11-01

    A conference is reported on technology development in the Soviet coking industry held on December 9-10, 1985 at the Khar'kov Scientific-Research Coal-Chemistry Institute. Representatives of leading research institutes and coking plants delivered 25 papers on the following topics: increasing flotation efficiency by means of new flotation reagents, drum feeders for charging cars, new design of coke oven doors, mathematical models of coal transport to coke ovens, some characteristics of packing coal mixtures in coke ovens, heat treatments of coal mixtures at the Khar'kov experimental coking plant, investigating properties of long-flame and gas coal from the Donbaas used for manufacturing formed coke, modernization of the IGI-DMeTI method for determining properties of coal mixtures for formed coke processes, basic problems associated with environmental protection in formed coke processes, specific problems of coal gasification at 900-1050 C and its effects on coking, evaluating properties of formed coke produced from black coal from the Western Donbass for metallurgy, mixing hot briquets with coal slurries during partial briquetting of the coal charge.

  19. Fluid coking of heavy hydrocarbons and apparatus therefor

    Energy Technology Data Exchange (ETDEWEB)

    1956-07-11

    A process for the conversion of hydrocarbon oils comprises injecting a plurality of streams of oil into an enlarged coking vessel containing a mass of finely divided solids, thereby, preventing agglutination of the solids, circulating the solids through an external heating zone and back to the coking vessel to maintain the vessel at a coking temperature between 850 and 1,200/sup 0/F, passing gaseous material upwardly through the coking vessel at a superficial velocity of between 0.1 and 5.0 feet per second, controlled to maintain the body of solids in a dense turbulent fluidized state, maintaining the oil within coking the vessel for a period sufficient to convert into vapors and coke, withdrawing vapors from the top of the vessel through an outlet, separating high-boiling ends from vapors, returning at least a portion of the high-boiling ends to the coking vessel for further cracking and withdrawing excess of coke formed in the process.

  20. Briquetting and coking behavior of Bobov-Dol coal

    Energy Technology Data Exchange (ETDEWEB)

    Naundorf, W.

    1987-01-01

    Hard Bulgarian glance brown coal (23.2% ash content, 16% coal moisture 2.39% sulfur) was studied for its general suitability for partial black coal coke substitution in coking plants and for the possibility of producing pyrolysis briquets for coking purposes. Laboratory briquetting variants include coal briquetting without binders, with sulfite lye as binder, briquetting after partial demineralization by wet classification, briquetting of different screening fractions (0 to 4 mm), briquetting as a mixture with type 35 caking black coal as well as mixed with type 34 less caking black coal under addition of black coal tar, pitch or bitumen. Coking of the briquets produced was carried at with and without charge compacting. Graphs and tables provide briquetting and coking results. It is concluded that high strength coke can be produced from this brown coal, but it can only be used commercially as heating coke due to its high ash and sulfur content. Briquetting and coking of partially demineralized brown coal in a mixture with black coal and binders resulted in suitable metallurgical coke. Maximum percentage of brown coal in the briquetting mixture was 30%. 4 refs.

  1. Hydrotreating catalyst deactivation by coke from SRC-II oil

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Y.; Kumata, F.; Massoth, F.E.

    1988-10-01

    Samples of a CoMo/Al/sub 2/O/sub 3/ catalyst were partially deactivated with SRC-II feed in an autoclave reactor to give coked samples of 5 to 18% C. The coked catalysts were analyzed for surface area, pore volume, coronene adsorption and diffusivity, and their catalytic activity determined for hydrodesulfurization (HDS), hydrodeoxygenation (HDO) and C-N hydrogenolysis (CNH) using model compounds. All of the above measurements decreased with increase in coke content. Property data indicate that some pores are blocked by coke and diffusivity results show narrowing of pore mouths with increasing coke content. Catalyst deactivation versus coke level was identical for HDS and HDO, but less for CNH. A simple model of coke deactivation was developed to relate activity to coke content. Coke is envisioned as forming wedge-like deposits in the catalyst pores. 11 refs., 5 figs., 3 tabs.

  2. Coke breakage behaviour in relation to its structure

    Energy Technology Data Exchange (ETDEWEB)

    Peirce, T J; Horton, A E; Tucker, J

    1980-06-14

    The relationship between coke macrostructure and volumetric (coarse) breakage behaviour, and the manner in which both features are affected by the coal charge composition are discussed. Coke pieces which are extensively fissured fail spontaneously after only a few revolutions in the drum; coke pieces which are less fissured require an extended treatment in the drum and finally fail in a manner consistent with that of fatigue crack growth induced by repeated impact. This heterogeneity in breakage behaviour was demonstrated in terms of an abrupt change in gradient of the Weibull distribution function for the coke. Heterogeneity may be removed by fully stabilising the coke or by the use of a more energetic test method. The role of fatigue crack growth in coke breakage was studied by cutting fissures of defined depth in full stabilised coke and assessing the rate of crack growth as a function of fissure depth and fracture toughness. The form of the results was consistent with that given by the Paris-Erdogan law and the rate of crack growth (for a given stress intensity level) was shown to increase with reducing coke toughness. Explanations are suggested to account for the role of blend additives in modifying the fissured properties and fracture toughness of coke made from high-volatile coal.

  3. Scientific Council on problems on new processes in the coking industry. [Effect on coke consumption of moisture, sulfur and ash; substitution possibility

    Energy Technology Data Exchange (ETDEWEB)

    Filippov, B.S.

    1981-07-01

    This paper presents a report on the Coking Section of the Scientific Council held on November 20, 1980 in Moscow. The following problems were discussed: indexes characterizing blast furnace coke (for furnaces with a volume of 5580 M/sup 3/); replacing metallurgical coke with other types of fuels; use of brown coal; liners of coke ovens. Papers delivered during the session are summarized. Reducing moisture content in blast furnace coke permits its consumption to be reduced by 2%. Reducing sulfur content in blast furnace coke by 0.1% permits its consumption to be reduced from 10 to 15 kg for 1 t of pig iron. Increase in ash content of coke by 1% causes coke consumption increase ranging from 1.5 to 2.0%. About 10 Mmt of coke class with grains above 25 mm in USSR is used for purposes other than blast furnaces. Possibilities of substituting coke with lean coal are evaluated (particularly from Kuzbass). A method for briquetting a mixture of black and brown coal is proposed. Briquets are a suitable fuel in metallurgy. A new type of liner, which consists of at least 92% silicon dioxide, is described. Physical and mechanical properties of the liners are discussed.

  4. Special analyses reveal coke-deposit structure

    International Nuclear Information System (INIS)

    Albright, L.F.

    1988-01-01

    A scanning electron microscope (SEM) and an energy dispersive X-ray analyzer (EDAX) have been used to obtain information that clarifies the three mechanisms of coke formation in ethylene furnaces, and to analyze the metal condition at the exit of furnace. The results can be used to examine furnace operations and develop improved ethylene plant practices. In this first of four articles on the analyses of coke and metal samples, the coking mechanisms and coke deposits in a section of tube from an actual ethylene furnace (Furnace A) from a plant on the Texas Gulf Coast are discussed. The second articles in the series will analyze the condition of the tube metal in the same furnace. To show how coke deposition and metal condition dependent on the operating parameters of an ethylene furnace, the third article in the series will show the coke deposition in a Texas Gulf Coast furnace tube (Furnace B) that operated at shorter residence time. The fourth article discusses the metal condition in that furnace. Some recommendations, based on the analyses and findings, are offered in the fourth article that could help extend the life of ethylene furnace tubes, and also improve overall ethylene plant operations

  5. Trends in the automation of coke production

    Energy Technology Data Exchange (ETDEWEB)

    R.I. Rudyka; Y.E. Zingerman; K.G. Lavrov [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Up-to-date mathematical methods, such as correlation analysis and expert systems, are employed in creating a model of the coking process. Automatic coking-control systems developed by Giprokoks rule out human error. At an existing coke battery, after introducing automatic control, the heating-gas consumption is reduced by {>=}5%.

  6. Fluid coking : a competitive option for heavy feed processing

    International Nuclear Information System (INIS)

    Hammond, D.G.; Feinberg, A.S.; McCaffrey, D.S.

    1997-01-01

    Fluid coking is a proven thermal conversion process for converting heavy hydrocarbon feeds to lighter products. Fluid coking was commercialized by Exxon over 40 years ago. A total of 13 units have been built with over 330 years of cumulative operating experience. Fluid coking can process many different feeds at once and is usually insensitive to feed contaminants such as sulfur, nitrogen and metals. New developments in coke utilization and flue gas desulfurization/departiculation have prompted new economic studies. Fluid coking is competitive and is the most attractive option compared to delayed coking, particularly for very heavy feed stocks such as deasphalter bottoms. Viewgraphs describe the fluid coking process, its advantages, utilization, and commercial viability. 7 tabs., 3 figs

  7. Emission and source characterization of monoaromatic hydrocarbons from coke production

    Energy Technology Data Exchange (ETDEWEB)

    He, Q.S.; Wang, X.M.; Sheng, G.Y.; Fu, J.M. [Chinese Academy of Sciences, Guangzhou (China). State Key Laboratory of Organic Geochemistry

    2005-09-15

    Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

  8. [Emission and source characterization of monoaromatic hydrocarbons from coke production].

    Science.gov (United States)

    He, Qiu-Sheng; Wang, Xin-Ming; Sheng, Guo-Ying; Fu, Jia-Mo

    2005-09-01

    Monoaromatic hydrocarbons (MAHs) from indigenous and industrial coking processes are studied in Shanxi province. They are sampled on the top of coke ovens and in the chimneys using stainless steel canister and determined by GC/MSD after preconcentration with liquid nitrogen. Benzene, toluene and xylene are the main components among MAHs emitted from coking processes. Benzene and the total MAHs concentrations were as high as 3421.0 microg/m3 and 4 865.9 microg/m3 in the air from indigenous coking, 548.7 microg/m3 and 1 054.8 microg/m3 in the oventop air from industrial coking, and 1 376.4 microg/m3 and 1 819.4 microg/m3 in stack gas from industrial coking, respectively. The MAHs concentrations vary greatly during the indigenous coking process, which in the prophase (from firing to 10 days) is obviously higher than in the anaphase (10 days to quenching the coke). In industrial coking the MAHs in the oventop air are highest when charging the coal and next when transferring the hot coke, but in stack gas they are highest when charging coal and lowest when transferring the coke. Benzene, toluene, ethylbenzene and xylene (BTEX) in industrial coking samples show good linearity, indicating that MAHs in industrial coking might come predominantly from coal pyrolysis; but BTEX distribute dispersedly in indigenous coking samples, indicating that its emission might be affected by many factors. In all samples BTEX ratios especially high B/E ratio, is unique among MAHs sources, and might be helpful to characterize pollution from coking.

  9. Major growth in coke production takes place

    International Nuclear Information System (INIS)

    Swain, E.J.

    1991-01-01

    U.S. petroleum coke production has increased 64% during the 10-year period from 1980 to 1990. This dramatic rise makes it timely to discuss the history and future of U.S. coking capacity, production, and processing. The article covers the properties and uses of the various grades of petroleum coke, as well as pricing and market trends

  10. Cancer mortality among coke oven workers.

    OpenAIRE

    Redmond, C K

    1983-01-01

    The OSHA standard for coke oven emissions, which went into effect in January 1977, sets a permissible exposure limit to coke oven emissions of 150 micrograms/m3 benzene-soluble fraction of total particulate matter (BSFTPM). Review of the epidemiologic evidence for the standard indicates an excess relative risk for lung cancer as high as 16-fold in topside coke oven workers with 15 years of exposure or more. There is also evidence for a consistent dose-response relationship in lung cancer mort...

  11. Characterisation of coking activity during supercritical hydrocarbon pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Gascoin, Nicolas; Gillard, Philippe; Bernard, Stephane [Laboratoire Energetique, Explosion, Structure, UPRES-EA 1205, 63, avenue de Lattre de Tassigny, 18020 Bourges Cedex (France); Bouchez, Marc [MBDA France, 8, rue Le Brix, 18000 Bourges (France)

    2008-12-15

    The active cooling of the Supersonic Combustion Ramjet engine, for hypersonic flight purpose, is ensured thanks to fuel, n-dodecane for the present study. The endothermic fuel pyrolysis, starting above 800 K, could generate an unwanted coke formation. Experimental tests up to 1125 K and between 1 MPa and 6 MPa have been performed on the hydrocarbon fuel pyrolysis to evaluate the coking activity. 316L stainless steel, low carbon steel and titanium reactors have been considered. A witness of the coke formation, based on its thermal insulation and pressure loss effects, has been found. A correlation between methane production and coke deposit was found. The coke has been studied with Scanning Electron Microscope (SEM), Energy Dispersion Spectroscopy (EDS), X-ray diffractometer and Fourier Transform Infrared (FTIR) spectroscopy. The porosity, the density and the permeability of the coke have been estimated. (author)

  12. Genesis of natural cokes: Some Indian examples

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Ashok K.; Sharma, Mamta [Central Institute of Mining and Fuel Research, Dhanbad, PIN-828108 (India); Singh, Mahendra P. [Banaras Hindu University, Varanasi, PIN-221005 (India)

    2008-06-13

    In Indian coalfields huge amounts of natural coke have been produced due to magmatic intrusions. Jharia Coalfield in eastern part of India alone contains approximately 2000 Mt of baked coking coal as a consequence of these intrusions in the form of discordant and concordant bodies. This paper is an effort to investigate the effect of carbonization in two intrusion affected coal seams of Ena (seam XIII) and Alkusa (seam XIV) collieries of Jharia Coalfield. Natural coke is derived from coking coal under in-situ conditions due to intense magmatic induced heat and overburden pressure. Natural coke is characterized by the presence of low volatile matter and high ash contents and organic constituents showing isotropy and anisotropy. Through physical, petrographic and chemical properties of natural coke or 'jhama' as determined by various methods it has been established that the reactives in the unaltered coals (vitrinite, liptinite, pseudovitrinite, reactive semifusinite, etc.) are < 25.0 vol.%, moisture < 2.5%, volatile matter < 15.0% and hydrogen < 4.0%. The temperatures attained in the coal seams have been deciphered using some standard models, which indicate that a temperature {proportional_to} 1000 C was attained. This produced huge amount of anisotropic and deposited carbons. An attempt has been made to understand the factors that influence the genesis of natural coke and heat altered maceral products in coals in Indian coalfields. (author)

  13. Scientific and technical problems in the production of coke

    Energy Technology Data Exchange (ETDEWEB)

    Glushchenko, I M

    1979-05-01

    This paper lists several scientific and technological problems facing the producers of coke in the future. The demand for coke on the world market is steadily increasing despite the efforts of metallurgists to find non-coke methods of ore smelting. The major problems are held to be the gap between very successful results of research and the lack of their application to industry, unsatisfactory coke oven construction, problems in quenching and imperfections in the formed coke process. (In Russian)

  14. Study of phenol extraction from coke-chemical sources

    Energy Technology Data Exchange (ETDEWEB)

    Catana, E.; Mateescu, I.; Giurcaneanu, V.; Bota, T.

    1990-09-01

    The paper presents an experimental study of the phase equilibrium in the coke-chemical tarphenols-solvent system (NaOH) solution and (phenolate solution) implied in the extraction of the phenols from coke-chemical sources. The possibility of using the phenolate solution as an extraction agent, thus making possible the improvement of the specific consumption and also simplifying the problem of the corrosion and of the waste water at the same time is presented. The influence of the solvent tar mass ratio on the selectivity of the process is discussed, this criterion being considered for establishing the conditions of the extraction. 2 figs., 7 tabs., 13 refs.

  15. Scientific Council of the State Committee for Science and Technology on the problem 'New processes in the coking industry', Coke-Chemistry Section of the Scientific-Technical Council of the Ministry of Ferrous Metallurgy of the USSR and of the Central Administration of the Scientific-Technical Branch of Ferrous Metallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Bukvareva, O.F.

    1986-12-01

    A report is presented on 3 conferences on the development of the Soviet coking industry held in February and April 1986. Papers delivered at the conferences and selected recommendations for development of equipment for coking, coking systems, optimization of coal mixtures for coking, environmental protection and research programs on coking are reviewed. The following problems were discussed: modernization of coke oven design, selecting the optimum size of coke ovens, prospects for dry coke quenching in the USSR, evaluation of operation of systems for dry coke quenching, utilization of waste heat from coke quenching for heat treatment of coal mixtures for coking, research programs on coking in the 12th five-year plan (1986-1990), partial briquetting of coal mixtures for coking and selecting optimum binders for partial briqetting, formed coke processes, economic analysis of formed coke processes, fire-resistant bricks and elements for coke oven construction, new coking technologies, pollution control in coking plants.

  16. The influence of microporosity on resistance and carboxyreactivity of cokes

    Energy Technology Data Exchange (ETDEWEB)

    Medek, J.; Weishauptova, Z. [Academy of Sciences, Prague (Czech Republic). Inst. of Rock Structure and Mechanics

    1997-12-31

    Large sample collection of metallurgical cokes from Ostrava-Karvina coking plants, were used for correlation of the resistivity of the coke matter (carbon solid phase plus micropores) and carboxyreactivity of cokes with the value of microporosity. It results, from this correlation, that the characteristic values of the two mentioned quantities appartain to the solid phase of all metallurgical cokes studied, while the individual values of these quantities are caused by the different microporosity of the coke matter. The microporosity as a structure characteristic is a consequence of the discontinuity of the coke solid phase and can be quantitatively expressed as the degree of solid phase dispersion. (orig.)

  17. Coke fouling monitoring by electrical resistivity

    Energy Technology Data Exchange (ETDEWEB)

    Bombardelli, Clovis; Mari, Livia Assis; Kalinowski, Hypolito Jose [Universidade Tecnologica Federal do Parana (UTFPR), Curitiba, PR (Brazil). Programa de Pos-Graduacao em Engenharia Eletrica e Informatica Industrial (CPGEI)

    2008-07-01

    An experimental method to simulate the growth of the coke fouling that occurs in the oil processing is proposed relating the thickness of the encrusted coke to its electrical resistivity. The authors suggest the use of the fouling electrical resistivity as a transducer element for determining its thickness. The sensor is basically two electrodes in an electrically isolated device where the inlay can happen in order to compose a purely resistive transducer. Such devices can be easily constructed in a simple and robust form with features capable to face the high temperatures and pressures found in relevant industrial processes. For validation, however, it is needed a relationship between the electrical resistivity and the fouling thickness, information not yet found in the literature. The present work experimentally simulates the growth of a layer of coke on an electrically insulating surface, equipped with electrodes at two extremities to measure the electrical resistivity during thermal cracking essays. The method is realized with a series of consecutive runs. The results correlate the mass of coke deposited and its electrical resistivity, and it can be used to validate the coke depositions monitoring employing the resistivity as a control parameter. (author)

  18. Fundamentals of Delayed Coking Joint Industry Project

    Energy Technology Data Exchange (ETDEWEB)

    Michael Volk; Keith Wisecarver

    2003-09-26

    Delayed coking evolved steadily over the early to mid 1900s to enable refiners to convert high boiling, residual petroleum fractions to light products such as gasoline. Pound for pound, coking is the most energy intensive of any operation in a modern refinery. Large amounts of energy are required to heat the thick, poor-quality petroleum residuum to the 900 to 950 degrees F required to crack the heavy hydrocarbon molecules into lighter, more valuable products. One common misconception of delayed coking is that the product coke is a disadvantage. Although coke is a low valued (near zero economic value) byproduct, compared to transportation fuels, there is a significant worldwide trade and demand for coke as it is an economical fuel. Coke production has increased steadily over the last ten years, with further increases forecast for the foreseeable future. Current domestic production is near 111,000 tons per day. A major driving force behind this increase is the steady decline in crude quality available to refiners. Crude slates are expected to grow heavier with higher sulfur contents while environmental restrictions are expected to significantly reduce the demand for high-sulfur residual fuel oil. Light sweet crudes will continue to be available and in even greater demand than they are today. Refiners will be faced with the choice of purchasing light sweet crudes at a premium price, or adding bottom of the barrel upgrading capability, through additional new investments, to reduce the production of high-sulfur residual fuel oil and increase the production of low-sulfur distillate fuels. A second disadvantage is that liquid products from cokers frequently are unstable, i.e., they rapidly form gum and sediments. Because of intermediate investment and operating costs, delayed coking has increased in popularity among refiners worldwide. Based on the 2000 Worldwide Refining Survey published in the Oil and Gas, the delayed coking capacity for 101 refineries around the world

  19. Coke Formation During Hydrocarbons Pyrolysis. Part One: Steam Cracking Formation de coke pendant la pyrolise des hydrocarbures. Première partie : vapocraquage

    Directory of Open Access Journals (Sweden)

    Weill J.

    2006-11-01

    Full Text Available Thermal cracking is always accompanied by coke formation, which becomes deposited on the wall and limits heat transfers in the reactor while increasing pressure drops and possibly even plugging up the reactor. This review article covers undesirable coking operations in steam craking reactors. These coking reactions may take place in the gas phase and/or on the surface of the reactor, with coke being produced during pyrolysis by a complex mechanism that breaks down into a catalytic sequence and a noncatalytic sequence. After a brief description of different experimental set-ups used to measure the coke deposition, on the basis of research described in the literature, the different factors and their importance for coke formation are listed. In particular, we describe the effects of surface properties of stainless-steel and quartz reactors as well as the influence of the cracked feedstock, of temperature, of dilution, of residence time and of the conversion on coke deposition. Some findings about the morphology of coke are described and linked to formation mechanisms. To illustrate this review, some particularly interesting research is referred to concerning models developed to assess coke formation during propane steam cracking. Le craquage thermique est toujours accompagné de la formation de coke qui, en se déposant à la paroi, limite les transferts de chaleur au réacteur, augmente les pertes de charges et même peut boucher celui-ci. Cet article fait le point sur les réactions indésirables de cokage dans les réacteurs de vapocraquage. Ces réactions de cokage peuvent avoir lieu en phase gazeuse et/ou sur la surface du réacteur, le coke étant produit pendant la pyrolyse par un mécanisme complexe qui se décompose en une séquence catalytique et une séquence non catalytique. Après une brève présentation des différents montages expérimentaux utilisés pour mesurer le dépôt de coke, il est mentionné, à partir de travaux de la

  20. On-line determination of moisture in coke on conveyor belts

    International Nuclear Information System (INIS)

    Millen, M.J.; Rafter, P.T.; Sowerby, B.D.

    1988-01-01

    A fast neutron and γ-ray transmission technique is being developed for the on-line determination of moisture in coke on conveyor belts. Calculations show that the technique is capable of determining coke moisture to within 0.3 wt% for coke thicknesses down to 50 mm provided that count rates are measured to within 0.1% relative. Laboratory measurements on static and moving coke samples showed that coke moisture can be determined to within 0.25 and 0.45 wt% for crushed and lump coke, respectively. It is planned to carry out a long-term plant trial of the technique on lump coke feed to the No. 3 blast furnace at BHP, Newcastle, NSW, Australia. (author)

  1. Increasing efficiency of reconstruction and technological development of coking enterprises

    Energy Technology Data Exchange (ETDEWEB)

    Rozenfel' d, M.S.; Martynenko, V.M.; Tytyuk, Yu.A.; Ivanov, V.V.; Svyatogorov, A.A.; Kolomiets, A.F. (NIISP, Voroshilovgrad (USSR))

    1989-07-01

    Discusses problems associated with reconstruction of coking plants in the USSR. Planning coking plant reconstruction is analyzed. Duration of individual stages of plant reconstruction is considered. A method developed by the Giprokoks research institute for calculating reconstruction time considering duration of individual stages of coke oven battery repair is analyzed: construction of storage facilities, transport of materials and equipment, safety requirements, coke oven cooling, dismantling, construction of coke oven walls, installation of machines and equipment. Advantages of using the methods for analysis of coke oven battery reconstruction and optimization of repair time are discussed.

  2. System for reducing emissions during coke oven charging

    International Nuclear Information System (INIS)

    Schuecker, Franz-Josef

    2014-01-01

    This article describes a process which reduces emissions from coke production in coke plants. The focus is on the charging process, which can be partly responsible for the fact that statutory emissions limits, which were originally met, are exceeded as coke plants get older. This article presents a solution in the form of a newly developed system that allows the oven charging system - the charging car - to respond to age-related changes in the geometry of a coke oven and thereby reduce the level of emissions.

  3. Rapid production of metallurgical coke by a pressurized hot-briquetting method. Netsukan kaatsu seikei ni yoru cokes no jinsoku seizo no kokoromi

    Energy Technology Data Exchange (ETDEWEB)

    Miura, K.; Hayashi, J.; Noguchi, N. (Kyoto University, Kyoto (Japan). Research Laboratory of Carbonaceous Resources Conversion Technology); Hashimoto, K. (Kyoto University, Kyoto (Japan). Faculty of Engineering)

    1993-09-20

    Rapid production of metallurgical coke from non- and slightly coking coals was studied by pressurized hot-briquetting method. Coal specimens were filled into the mold after pulverizing, and heated at a constant temperature rise rate up to caking temperature under loading pressure to obtain caked coal specimens. Such specimens were then carbonized in nitrogen gas at 800[degree]C. As a result, the coke obtained was superior in compressive strength as compared with commercial cokes, however, its CO2 reactivity was very high requiring heating up to 1,000[degree]C to decrease it, while the reactivity was strongly dependent on coal kind. The optimum processing conditions for slightly coking coal were as follows; loading pressure: 10 [times] 10[sup 5] Pa or more, temperature range under loading pressure: 300-450[degree]C, temperature rise rate: 2-100[degree]C/min, and caking temperature: nearly 500[degree]C. No coke could be produced from coking coals because no volatile matter could be removed from it in a short time under pressure. 13 refs., 8 figs., 1 tab.

  4. Possibilities of using pulverized non coking coals in ironmaking

    Energy Technology Data Exchange (ETDEWEB)

    Wijk, Olle; Mathiesen, Mihkel; Eketorp, Sven

    1977-08-01

    The use of pulverized coal in iron making suggests solutions to the mounting problems created by the increasing scarcity of coking coals, and other fossil fuels such as oil and natural gas. The unavailability of coke can be met with two principally different measures. Blast furnace coke rates can be decreased by substituting injected pulverized coal or other carbon containing fuels for part of the coke burden, and the coke itself may be substituted by formed coke. A more radical solution is to abandon the blast furnace process, and instead produce the raw iron in processes not requiring coke. Two such processes are discussed in the paper, the Inred process, developed by Boliden Kemi AB, Sweden, and the smelting reduction process by means of injection, currently being developed at the Royal Institute of Technology in Stockholm. Both processes have potential advantages over the coke oven/sintering plant/blast furnace-complex especially concerning energy requirements and structure, but also in economical terms. The injection process seems to present a further advantage in the possibility of gasifying coal in the process, thus yielding a synthesis gas for methanol production in addition to the raw iron.

  5. The world coke market. Problems and outlook

    International Nuclear Information System (INIS)

    Anon.

    1998-01-01

    Outlooks to the world coke market are considered with regard to supply and demand as well as the current state of capacities for its production in some countries of Asia, Western and Eastern Europe, USA. In experts opinion increase of coke import from China, increase in service life of currently operating coke furnaces, as well as more extensive use of PCI coal mixture are among the most feasible opportunities for its Western consumers [ru

  6. Ways of improving preparatory stage and reconstruction of coking plants

    Energy Technology Data Exchange (ETDEWEB)

    Rozenfel' d, M.S.; Martynenko, V.M.; Svyatogorov, A.A.; Kvitkin, I.A.; Zhurba, A.I.; Gurtovnik, P.F.

    1987-06-01

    Discusses economic and technological aspects of coking plant reconstruction and modernization in the USSR. Effects of standardized technologies on plant reconstruction are analyzed. A standardized planning procedure jointly developed by research institutes in the USSR for plant modernization or reconstruction is discussed: selecting the optimum reconstruction and repair time, sequence of operations without stoppage of a coke oven battery, coke oven cooling, repair of coke oven liners, heating systems, coke oven equipment, drying, initial heating, testing battery equipment. The procedure is aimed at reducing coke losses and eliminating delays during reconstruction operations. A graphic method for modelling plant reconstruction is discussed.

  7. New formulae for the manufacture of formed coke of the ICEM type and carbonization of this type of coke in oblique ovens

    Energy Technology Data Exchange (ETDEWEB)

    Barbu, I.; Georgescu, I.

    1978-01-01

    This paper presents the industrial experiences between 1971 and 1976 which led to the elaboration of new formulae for the manufacture of ICEM type coke briquettes, plus the results of coking the latter in a vertical oven. The possibility of using this type of coke in the chemical industry and in metallurgy instead of ordinary coke was simultaneously examined but this proved unsuccessful. Gives a detailed report of all the tests carried out by the State undertaking, Victoria-Galan.

  8. Evaluation of coke microstructure and its effects on graphite fabrication

    International Nuclear Information System (INIS)

    Fotourehchian, S.; Ahmadi, S.

    2001-01-01

    A variety of applications for cokes (metallurgy, petroleum, etc.) have been defined in parallel to the new industrial technology growth. Coke is rich in carbon and has the main role in manufacturing carbonaceous materials such as graphite, steel, silicon carbide, titanium carbide, etc. Among the most important applications of different variety of cokes is their usage for different graphite fabrications. The crystalline structure of graphite (hexagonal with sp 2 hybrid) is based upon the microstructure of coke and it causes anisotropy in properties of produced graphite. Thus, the study of macrostructure and anisotropy degree of cokes is of importance. There are several theoretical and experimental methods to determine the Coke's microstructure and anisotropy. Numerous tests have been conducted on different variety of cokes based on the used method. Here, it is attempted to introduce an applied method to determine the microstructure and anisotropy degree of cokes based upon the kind of application

  9. Study on the Inference Factors of Huangling Coking Coal Pyrolysis

    Science.gov (United States)

    Du, Meili; Yang, Zongyi; Fan, Jinwen

    2018-01-01

    In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

  10. Giprokoks proposals for improvement in air quality at coke battery 1A of Radlin coke plant

    Energy Technology Data Exchange (ETDEWEB)

    T.F. Trembach; A.G. Klimenko [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Coke battery 1A, which uses rammed batch, has gone into production at Radlin coke plant (Poland), on the basis of Giprokoks designs. Up-to-date dust-trapping methods are used for the first time within the aspiration systems in the coal-preparation shop and in improving dust collection within the production buildings.

  11. Upgrading oil sands bitumen with FLUID COKING and FLEXICOKING technologies

    Energy Technology Data Exchange (ETDEWEB)

    Kamienski, P.; Phillips, G. [ExxonMobil Research and Engineering Co., Fairfax, VA (United States); McKnight, C.; Rumball, B. [Syncrude Canada Ltd., Calgary, AB (Canada)

    2009-07-01

    This presentation described EMRE's Fluid Coking and Flexicoking technologies that are well suited for upgrading Alberta's heavy crudes and oil sands bitumen into pipelineable crudes or synthetic crudes, which can be further processed into transportation fuels. The Fluid Coking technology uses a fluidized bed reactor that thermally converts the heavy oils into light gases, liquids and coke. The metals and much of the sulphur are concentrated in the coke. Combustion of the coke provides process heat and the remaining coke is sold or stored on site for later recovery. Syncrude Canada currently operates 3 Fluid Coking units in northern Alberta. Flexicoking extends fluid coking by integrating air gasification to produce a carbon monoxide/hydrogen rich fuel gas that helps meet fuel and energy requirements of bitumen recovery and upgrading. The yields of light gas and liquids are similar to those of the Fluid Coking process. The partial combustion of coke provides the process heat for the thermal conversion and gasification steps. The remaining coke is gasified and desulphurized using Flexsorb technology. At present, there are 5 Flexicoking units in operation around the world. Interest in the technology is growing, particularly in locations with large demand for clean fuel or electricity. It is also suitable for steam assisted gravity drainage (SAGD) operations in Alberta. This presentation outlined the operating principles of the Flexicoking integrated gasification system and compared it with more expensive oxygen gasification processes. tabs., figs.

  12. Operation car for horizontal coke ovens. Bedienungswagen fuer waagrechte Verkokungsoefen

    Energy Technology Data Exchange (ETDEWEB)

    Kwasnik, H J; Piduch, H G

    1981-07-30

    An operation car which is driveable on the coke side of a coke oven battery is described. The operation car is equipped with a door lifter, a door and frame cleaner, a coke guiding grid and a collection hood for emissions developed on coke pushing. The car has a portal construction and it is driveable on both sides of the path of the coke receiving car. The operation has a considerable lower weight than usual cars. (HGOE).

  13. Utilization of formed coke from HBNPC in the Dunkerque blast furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Le Scour, C; Capelani, R

    1978-01-01

    Recalls the aspects involved in the manufacture of formed coke together with the coke characteristics. Describes the features of blast-furnaces No. 1 and No. 2 at Dunkerque. The blend used for producing the ovoids is composed of 70 to 80% non-coking coal and the ovoids are carbonized at 900 C. The first stage of the tests was carried out with 25% formed coke and the second stage with 22%. The formed coke was charged separately. The results were as follows: the coke rate was comparable and the permeability identical; there was no change in the behaviour of the furnace chamber and no problems were experienced at the hearth stage. The replacement of 30% of the conventional coke by HBNPC formed coke seemed a practical proposition.

  14. Process for the preparation of isotropic petroleum coke

    International Nuclear Information System (INIS)

    Kegler, W.H.; Huyser, M.E.

    1975-01-01

    A description is given of a process for preparing isotropic coke from oil residue charge. It includes blowing air into the residue until it reaches a softening temperature of around 49 to 116 deg C, the deferred coking of the residue having undergone blowing at a temperature of around 247 to 640 deg C, at a pressure between around 1.38x10 5 and 1.72x10 6 Pa, and the recovery of isotropic coke with a thermal expansion coefficient ratio under 1.5 approximately. The isotropic coke is used for preparing hexagonal graphite bars for nuclear reactor moderators [fr

  15. Reducing dust emissions at OAO Alchevskkoks coke battery 10A

    Energy Technology Data Exchange (ETDEWEB)

    T.F. Trembach; E.N. Lanina [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Coke battery 10A with rammed batch is under construction at OAO Alchevskkoks. The design documentation developed by Giprokoks includes measures for reducing dust emissions to the atmosphere. Aspiration systems with dry dust trapping are employed in the new components of coke battery 10A and in the existing coke-sorting equipment. Two-stage purification of dusty air in cyclones and bag filters is employed for the coke-sorting equipment. This system considerably reduces coke-dust emissions to the atmosphere.

  16. Fundamentals of Delayed Coking Joint Industry Project

    Energy Technology Data Exchange (ETDEWEB)

    Michael Volk Jr; Keith Wisecarver

    2005-10-01

    Delayed coking evolved steadily over the early to mid 1900s to enable refiners to convert high boiling, residual petroleum fractions to light products such as gasoline. Pound for pound, coking is the most energy intensive of any operation in a modern refinery. Large amounts of energy are required to heat the thick, poor-quality petroleum residuum to the 900 to 950 degrees F required to crack the heavy hydrocarbon molecules into lighter, more valuable products. One common misconception of delayed coking is that the product coke is a disadvantage. Although coke is a low valued (near zero economic value) byproduct, compared to transportation fuels, there is a significant worldwide trade and demand for coke as it is an economical fuel. Coke production has increased steadily over the last ten years, with further increases forecast for the foreseeable future. Current domestic production is near 111,000 tons per day. A major driving force behind this increase is the steady decline in crude quality available to refiners. Crude slates are expected to grow heavier with higher sulfur contents while environmental restrictions are expected to significantly reduce the demand for high-sulfur residual fuel oil. Light sweet crudes will continue to be available and in even greater demand than they are today. Refiners will be faced with the choice of purchasing light sweet crudes at a premium price, or adding bottom of the barrel upgrading capability, through additional new investments, to reduce the production of high-sulfur residual fuel oil and increase the production of low-sulfur distillate fuels. A second disadvantage is that liquid products from cokers frequently are unstable, i.e., they rapidly form gum and sediments. Because of intermediate investment and operating costs, delayed coking has increased in popularity among refiners worldwide. Based on the 2000 Worldwide Refining Survey published in the Oil and Gas, the delayed coking capacity for 101 refineries around the world

  17. Statistical assessment of coal charge effect on metallurgical coke quality

    Directory of Open Access Journals (Sweden)

    Pavlína Pustějovská

    2016-06-01

    Full Text Available The paper studies coke quality. Blast furnace technique has been interested in iron ore charge; meanwhile coke was not studied because, in previous conditions, it seemed to be good enough. Nowadays, requirements for blast furnace coke has risen, especially, requirements for coke reactivity. The level of reactivity parameter is determined primarily by the composition and properties of coal mixtures for coking. The paper deals with a statistical analysis of the tightness and characteristics of the relationship between selected properties of coal mixture and coke reactivity. Software Statgraphic using both simple linear regression and multiple linear regressions was used for the calculations. Obtained regression equations provide a statistically significant prediction of the reactivity of coke, or its strength after reduction of CO2, and, thus, their subsequent management by change in composition and properties of coal mixture. There were determined indexes CSR/CRI for coke. Fifty – four results were acquired in the experimental parts where correlation between index CRI and coal components were studied. For linear regression the determinant was 55.0204%, between parameters CRI – Inertinit 21.5873%. For regression between CRI and coal components it was 31.03%. For multiple linear regression between CRI and 3 feedstock components determinant was 34.0691%. The final correlation has shown the decrease in final coke reactivity for higher ash, higher content of volatile combustible in coal increases the total coke reactivity and higher amount of inertinit in coal increases the reactivity. Generally, coke quality is significantly affected by coal processing, carbonization and maceral content of coal mixture.

  18. The coke drum thermal kinetic effects

    Energy Technology Data Exchange (ETDEWEB)

    Aldescu, Maria M.; Romero, Sim; Larson, Mel [KBC Advanced Technologies plc, Surrey (United Kingdom)

    2012-07-01

    The coke drum thermal kinetic dynamics fundamentally affect the coker unit yields as well as the coke product properties and unit reliability. In the drum the thermal cracking and polymerization or condensation reactions take place in a semi-batch environment. Understanding the fundamentals of the foaming kinetics that occur in the coke drums is key to avoiding a foam-over that could result in a unit shutdown for several months. Although the most dynamic changes with time occur during drum filling, other dynamics of the coker process will be discussed as well. KBC has contributed towards uncovering and modelling the complexities of heavy oil thermal dynamics. (author)

  19. A hydraulic device for unloading coke

    Energy Technology Data Exchange (ETDEWEB)

    Kretinin, M.V.; Abizgildin, U.M.; Kirillov, T.S.; Makarov, M.I.; Prokopov, O.I.; Solov' ev, A.M.

    1979-07-15

    A hydraulic device for unloading petroleum coke from slow carbonization chambers is characterized by an arrangement whereby in order to increase the output of large size coke by controlling the increment of the cutting line of the coke, the mechanism used to move the rod in the hydraulic cutter is built in the form of a rod rotation rotor; a gear wheel is mounted on the immobile section of this rotor, and on the mobile section a multi-stage regulator is installed. The drive gear of the regulator is engaged with the gear wheel, while the driven gear is connected to the rack, which is fastened to the rod.

  20. Application of flotational reagents obtained from coke-industry byproducts

    Energy Technology Data Exchange (ETDEWEB)

    N.I. Nikitin; I.N. Nikitin; N.I. Toporkova [Khar' kov Polytechnic Institute (Ukraine)

    2007-06-15

    Today, the operational efficiency of coal-preparation shops at coke plants largely depends on the flotation process, since flotation is the basic method of regenerating the slurry water in the water-slurry systems and the basic enrichment process for small-grain coal slurries. At The Coal-Chemistry Institute, attempts have been made to address the growing demand for readily available and relatively inexpensive flotational reagents. In particular, a list of promising coke-industry byproducts for use as flotational reagents has been compiled, and the possibility of reducing their toxicity has been established. In addition, various industrial byproducts and wastes have been investigated in terms of flotational activity.

  1. Fatigue behaviour of coke drum materials under thermal-mechanical cyclic loading

    Directory of Open Access Journals (Sweden)

    Jie Chen

    2014-01-01

    Full Text Available Coke drums are vertical pressure vessels used in the delayed coking process in petroleum refineries. Significant temperature variation during the delayed coking process causes damage in coke drums in the form of bulging and cracking. There were some studies on the fatigue life estimation for the coke drums, but most of them were based on strain-fatigue life curves at constant temperatures, which do not consider simultaneous cyclic temperature and mechanical loading conditions. In this study, a fatigue testing system is successfully developed to allow performing thermal-mechanical fatigue (TMF test similar to the coke drum loading condition. Two commonly used base and one clad materials of coke drums are then experimentally investigated. In addition, a comparative study between isothermal and TMF lives of these materials is conducted. The experimental findings lead to better understanding of the damage mechanisms occurring in coke drums and more accurate prediction of fatigue life of coke drum materials.

  2. Coking coal outlook from a coal producer's perspective

    International Nuclear Information System (INIS)

    Thrasher, E.

    2008-01-01

    Australian mine production is recovering from massive flooding while Canadian coal shipments are limited by mine and rail capacity. Polish, Czech, and Russian coking coal shipments have been reduced and United States coking coal shipments are reaching their maximum capacity. On the demand side, the Chinese government has increased export taxes on metallurgical coal, coking coal, and thermal coal. Customers seem to be purchasing in waves and steel prices are declining. This presentation addressed the global outlook for coal as well as the challenges ahead in terms of supply and demand. Supply challenges include regulatory uncertainty; environmental permitting; labor; and geology of remaining reserves. Demand challenges include global economic uncertainty; foreign exchange values; the effect of customers making direct investments in mining operations; and freight rates. Consolidation of the coal industry continued and several examples were provided. The presentation also discussed other topics such as coking coal production issues; delayed mining permits and environmental issues; coking coal contract negotiations; and stock values of coking coal producers in the United States. It was concluded that consolidation will continue throughout the natural resource sector. tabs., figs

  3. World coking coal markets

    International Nuclear Information System (INIS)

    McCloskey, G.

    2010-01-01

    This article discussed conditions in world coking coal markets. There is increased demand from Asia for metallurgical coal imports. World iron production was up 22 percent in first 7 months of 2010. Supply is up in Australia, the United States, Canada, New Zealand, Russia, and Mongolia, but the unexpected surge in supply caused prices to drop following a robust start to the year. Coking coal exports are up for the United States and Australia, but a delay in expanded production is expected until 2014. There is increased demand from Brazil, India, Taiwan, South Korea, and Japan as well as new plants in Thailand, Indonesia, and Brazil. Unexpectedly, Australia is backing out of the Chinese market but increasing exports to Japan and South Korea. India is seeing flat performance in iron production and imports, and the United States has surged back into Asia. A considerable increase is expected in the seaborne import requirement by 2020. Prices are expected to fall and then rise. This presentation also discussed whether coking coal index pricing is impossible or inevitable. 3 tabs., 5 figs.

  4. Analysis of industrial coke samples by activation with cyclotron protons

    International Nuclear Information System (INIS)

    Chaudhri, M.A.; Lee, M.M.; Spicer, B.M.

    1982-01-01

    A Melbourne Petrochemical Company was experiencing excessive coke formation in its ''cracking furnaces'', which was causing unnecessary stoppage of production and wastage of energy due to additional insulation. In order to investigate the possible causes of this excessive coke formation, we analyzed various coke samples and other coke-like materials obtained from these furnaces by activation with cyclotron-protons. Our results showed that, out of the two suspected coke promoters As and Sb whose small concentration in feed would produce greatly accelerated coke formation, As could not be detected in any of the eight samples investigated, while Sb was present in only one sample. However, we did observe Ca, Cr and Fe in all the samples, with surprisingly high concentrations in some of them. It has, therefore, been suggested that Ca, and perhaps Cr and Fe, but not As or Sb, could have been responsible for the excessive coke formation in the ''cracking furnaces''

  5. Characterization of norm sources in petroleum coke calcining processes - 16314

    International Nuclear Information System (INIS)

    Hamilton, Ian S.; Halter, Donald A.; Fruchtnicht, Erich H.; Arno, Matthew G.; Haumann, Donald F

    2009-01-01

    Petroleum coke, or 'petcoke', is a waste by-product of the oil refining industry. The majority of petcoke consumption is in energy applications; catalyst coke is used as refinery fuel, anode coke for electricity conduction, and marketable coke for heating cement kilns. Roskill has predicted that long-term growth in petroleum coke production will be maintained, and may continue to increase slightly through 2012. Petcoke must first be calcined to drive off any undesirable petroleum by-products that would shorten the coke product life cycle. As an example, the calcining process can take place in large, rotary kilns heated to maximum temperatures as high as approximately 1400-1540 deg. C. The kilns and combustion/settling chambers, as well as some cooler units, are insulated with refractory bricks and other, interstitial materials, e.g., castable refractory materials, to improve the efficiency of the calcining process. The bricks are typically made of 70-85-percent bauxite, and are slowly worn away by the calcining process; bricks used to line the combustion chambers wear away, as well, but at a slower rate. It has been recognized that the refractory materials contain slight amounts of naturally occurring radioactive materials (NORM) from the uranium- and thorium-decay series. Similarly, low levels of NORM could be present in the petcoke feed stock given the nature of its origin. Neither the petcoke nor the refractory bricks represent appreciable sources of radiation or radioactive waste. However, some of the demolished bricks that have been removed from service because of the aforementioned wearing process have caused portal alarms to activate at municipal disposal facilities. This has lead to the current investigation into whether there is a NORM concentrating mechanism facilitated by the presence of the slightly radioactive feed stock in the presence of the slightly radioactive refractory materials, at calcining-zone temperatures. Research conducted to date has been

  6. Microstructures and microtextures of natural cokes: A case study of heat-affected coking coals from the Jharia coalfield, India

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Ashok K. [Central Fuel Research Institute, CSIR, Dhanbad-828108 (India); Singh, Mahendra P. [Department of Geology, Banaras Hindu University, Varanasi-221005 (India); Sharma, Mamta; Srivastava, Sunil K.

    2007-07-02

    In Jharia coalfield, nearly 1250 Mt of coking coal has been devolatilized due to igneous intrusives and {proportional_to} 1900 Mt due to mine fires. This paper is an effort to investigate the effect of carbonization in two intrusive affected coal seams of Ena (seam XIII) and Alkusa (seam XIV) collieries of this coalfield. Through petrographic studies by microscopy, characterization of normal and heat-affected coals was carried out. The microstructures and microtextures produced due to extraneous heat have been related to nature and extent of heat, location of heating source, and quality and quantity of natural coke produced. Based on the results of this study and earlier studies, an effort has been made to study the classification scheme for microtextures of natural cokes generated through in-situ carbonization of the coal seams. It has been observed that in case of such heat effects under overburden pressure, the anisotropy is much more pronounced as compared to laboratory-carbonized cokes. In the mildly carbonized coals (pre-plastic phase, < 300 C) the vitrinite attained higher reflectance than normal vitrinite, liptinite started disappearing, and inertinite remained unaffected. In the moderately affected coals (plastic phase, 300-500 C), mesophase spheres and fused natural cokes were generated from the reactives (vitrinite and liptinite maceral groups), the liptinites disappeared, and structurally, the inertinites remained almost unchanged with slight increase in the reflectance value. In the severely heat-affected coals (post plastic phase, > 500 C) the identified microtextures were mesophase spheres, different shapes and sizes of natural cokes, graphitic sphaeroliths, pyrolytic carbons, inerts with morpho-structural changes and slightly higher reflectance values, and altered and unaltered mineral matters. A gradual change in the heat-affected coals with increasing temperature was observed with respect to location of intrusive body. It has been concluded that

  7. Coal and coke applied to metallurgy. Vol. 2. Carvao e coque aplicados a metalurgia

    Energy Technology Data Exchange (ETDEWEB)

    Masuda, H.

    1983-01-01

    Papers include: coking; control of pollution from coking plants; handling and storage of coal; preparation of coal for coking; politics of the supply of coal; coke for blast furnaces; selective preparation and briquetting of coal for coking; cooling and drying of coke; preheating of coal for coking; formed coke.

  8. Study on treatment of distilled ammonia waste water from coke plant with activated carbon-NaClO catalytic oxidation method

    Energy Technology Data Exchange (ETDEWEB)

    Luo, D.; Yi, P.; Liu, J.; Chen, A. [Xiangtan Polytechnic University, Xiangtan (China). Dept. of Chemical Enginering

    2001-12-01

    Catalytic oxidation method for the treatment of distilled ammonia waste water from coke plant was investigated using activated carbon as catalyst and NaClO as oxidant. The influences of main factors, such as NaClO, activated carbon, pH and reactionary time were discussed. The results showed that under the conditions of 25{degree}C, NaClO/CODO=1.5, carbon/NaClO=0.6 and pH=3.0, the reaction completed within 120 minutes with 99.5% of phenol removal and 75.8% of COD removal when the distilled ammonia waste water from coke plant which containing phenol 510 mg/L and CODO 8420 mg/L was treated. 13 refs., 4 figs.

  9. Calcinating petroleum coke in a furnace with a rotating hearth

    Energy Technology Data Exchange (ETDEWEB)

    Akhmetov, M M; Ezhov, B M; Galeeva, Z G; Goriunov, V S; Karpinskaia, N N; Zaitseva, S A

    1980-01-01

    A scheme is described for an industrial device with a bottom furnace for calcinating coke from slow coking. The consumption and operational indicators of the process during the calcination of standard and needle cokes are given, together with data on the quality of dry and calcinated cokes under different conditions. The basic drawbacks in the operation of the device are described, and measures are proposed for increasing its operational effectiveness.

  10. Effects of heat treatments of coal on coke destruction under blast furnace conditions

    Energy Technology Data Exchange (ETDEWEB)

    Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

    1983-09-01

    This paper discusses results of investigations on effects of chemical reactions in a blast furnace on coke disintegration and destruction. The investigations were carried out by the VUKhIN Institute branch in Kuznetsk. Effects of silicates and carbonates of sodium, potassium and zinc on mechanical coke properties were investigated under laboratory conditions. Coke samples were placed in a reactor and were treated by vapors of metal compounds. Coke produced from a coal mixture with conventional moisture content and from preheated coal mixture was used. Coal properties are given in a table. Design of laboratory equipment used for tests is shown in 2 schemes. Heat treatments influenced coke porosity and its structural strength. Proportion of large pores accessible to sodium and potassium in coke from preheated coal was 4.5 times lower than in coke from a conventional mixture. Adsorption of sodium and potassium on coke from preheated charge was lower (from 0.22% to 0.24%) than on coke from a conventional mixture (from 2.5% to 2.9%). Adsorption of alkali metals on coke reduced its structural strength and increased coke oxidation rate by carbon dioxide. Use of heat treatments of coal for coking reduced adsorption of alkali metals on coke in a blast furnace, increased coke structural strength and reduced coke oxidation rate by carbon dioxide. (16 refs.) (In Russian)

  11. Fissure formation in coke. 1: The mechanism of fissuring

    Energy Technology Data Exchange (ETDEWEB)

    D.R. Jenkins; M.R. Mahoney; J.C. Keating [CSIRO Mathematical and Information Sciences, North Ryde, NSW (Australia)

    2010-07-15

    Pilot scale coke oven experiments, in which carbonisation has been arrested after 2 and 4 h, have been used to identify key aspects of the initial formation and propagation of fissuring in coke. The experiments show that the primary fissure network is formed within the first few hours of coking and the fissures propagate towards the centre of the oven as coking progresses. They also show that some of the initially formed fissures stop propagating, thus increasing the effective fissure spacing as coking continues. A model for the propagation of regular crack arrays has been used to identify the cause of the initial formation of the fissure network, evaluate the fissure spacing and explain the fissure coarsening effect. The coarsening is shown to be due to an instability, in the form of every second fissure stopping. The formation of lateral fissures is shown to be due to tensile stress formation near the tips of stopped fissures and also to increased shrinkage due to a maximum in the coke contraction coefficient at around 700{sup o}C. 45 refs., 11 figs., 1 tab.

  12. Coke degradation by surface breakage in a modified tumble drum

    Energy Technology Data Exchange (ETDEWEB)

    Litster, J D

    1987-01-01

    The surface breakage rate constant for three Australian battery cokes was measured in a specially modified tumble drum using a previously developed technique. The effect of experimental test parameters - coke size, sample mass, drum speed, lifter height and lifter number - on the surface breakage rate constant was examined. The motion of coke particles within a tumble drum was filmed in a simulation experiment with a 0.31 m diameter drum. Particles were raised on the lifters, fell and collided with the bottom of the drum. These collisions were the main source of fines (minus 1 mm) production rather than true abrasion as depicted by a rubbing, rolling action. Hence the term 'surface breakage' is more appropriate than 'abrasion' to describe the breakage process. By measuring the volume of coke carried by each lifter and the height of fall of the coke, the effect of drum speed, sample mass, lifter height and number on the rate of surface breakage was successfully explained. The surface breakage rate constant was found to be proportional to particle size to the power 0.33 for the three cokes studied. A normalized surface breakage rate constant was derived which allowed comparison of cokes with different size distributions. This parameter characterises the coke surface breakage resistance.

  13. Quantification of mineral matter in commercial cokes and their parent coals

    Energy Technology Data Exchange (ETDEWEB)

    Sakurovs, Richard; French, David; Grigore, Mihaela [CRC for Coal in Sustainable Development, CSIRO Energy Technology, PO Box 330 Newcastle 2300 (Australia)

    2007-10-01

    The nature of mineral matter in coke is an important factor in determining the behaviour of coke in the blast furnace. However, there have been few quantitative determinations of the types of mineral matter in coke and the feed coal. Here we use a technique of quantitative X-ray diffraction - SIROQUANT trademark - to determine the nature and quantity of mineral matter in eleven cokes and their parent materials, using samples of coals and their cokes utilised commercially in blast furnaces around the world. In some of these coals a considerable proportion of the phosphorus was present as goyazite, an aluminium phosphate. In the cokes, most of the iron was incorporated into amorphous aluminosilicate material; metallic iron accounted for about 15% of the iron present, and a similar amount was present as sulfides. Potassium and sodium were largely present as amorphous aluminosilicate material. Most of the quartz in the coal was unaffected by the coking, but a small fraction was transformed into other minerals. Quartz is not completely inert during coking. The amount of the catalytic forms of iron in the coke - iron, iron oxides and iron sulfides - was not related to the amount of pyrite and siderite in the starting coal, indicating that estimation of catalytic iron requires investigation of the mineral matter in coke directly and cannot be estimated from the minerals in the coal. (author)

  14. Mean-term forecast of coke production in the world

    International Nuclear Information System (INIS)

    Ukhmylova, G.S.

    1996-01-01

    The causes of decrease in consumption of metallurgical coke in the world in the ninetieth and at the present time are analyzed. Reduction of reliable coke supply sources to the world market is noted. The data on the coke import and export in the world in 1990-1994 are presented and corresponding forecasts for 2000 and 2005 are given

  15. Using helical compressors for coke gas condensation

    Energy Technology Data Exchange (ETDEWEB)

    Privalov, V E; Rezunenko, Yu I; Lelyanov, N V; Zarnitzkii, G Eh; Gordienko, A A; Derebenko, I F; Venzhega, A G; Leonov, N P; Gorokhov, N N

    1982-08-01

    Coke oven gas compression is discussed. Presently used multilevel piston compressors are criticized. The paper recommends using helical machines which combine advantages of using volume condensing compressors and compact high-efficiency centrifugal machines. Two kinds of helical compressors are evaluated: dry and oil-filled; their productivities and coke oven gas chemical composition are analyzed. Experiments using helical compressors were undertaken at the Yasinovskii plant. Flowsheet of the installation is shown. Performance results are given in a table. For all operating conditions content of insolubles in oil compounds is found to be lower than the acceptable value (0.08%). Compressor productivity measurements with variable manifold pressure are evaluated. Figures obtained show that efficient condensation of raw coke oven gas is possible. Increasing oil-filled compressor productivity is recommended by decreasing amount of oil injected and simultaneously increasing rotation speed. The dry helical compressor with water seal is found to be most promising for raw coke oven gas condensation. (10 refs.)

  16. Study of variation grain size in desulfurization process of calcined petroleum coke

    Science.gov (United States)

    Pintowantoro, Sungging; Setiawan, Muhammad Arif; Abdul, Fakhreza

    2018-04-01

    Indonesia is a country with abundant natural resources, such as mineral mining and petroleum. In petroleum processing, crude oil can be processed into a source of fuel energy such as gasoline, diesel, oil, petroleum coke, and others. One of crude oil potentials in Indonesia is petroleum coke. Petroleum coke is a product from oil refining process. Sulfur reducing process in calcined petroleum cokes can be done by desulfurization process. The industries which have potential to become petroleum coke processing consumers are industries of aluminum smelting (anode, graphite block, carbon mortar), iron riser, calcined coke, foundry coke, etc. Sulfur reducing process in calcined petroleum coke can be done by thermal desulfurization process with alkaline substance NaOH. Desulfurization of petroleum coke process can be done in two ways, which are thermal desulfurization and hydrodesulphurization. This study aims to determine the effect of various grain size on sulfur, carbon, and chemical bond which contained by calcined petroleum coke. The raw material use calcined petroleum coke with 0.653% sulfur content. The grain size that used in this research is 50 mesh, then varied to 20 mesh and 100 mesh for each desulfurization process. Desulfurization are tested by ICP, UV-VIS, and FTIR to determine levels of sulfur, carbon, chemical bonding and sulfur dissolved water which contained in the residual washing of calcined petroleum coke. From various grain size that mentioned before, the optimal value is on 100 mesh grain size, where the sulfur content in petroleum coke is 0.24% and carbon content reaches the highest level of 97.8%. Meanwhile for grain size 100 mesh in the desulfurization process is enough to break the chemical bonds of organic sulfur in petroleum coke.

  17. Coke formation on hydrodesulphurization catalysts. [Including effects of different promoters

    Energy Technology Data Exchange (ETDEWEB)

    Ternan, M.; Furimsky, E.; Parsons, B.I.

    1979-02-01

    The extent of coke formation was measured on a number of different hydrodesulfurization catalysts, primarily as a function of the catalyst chemical composition. Variations in the concentration of MoO/sub 3/ on the alumina, the type of catalyst promoter, the promoter/MoO/sub 3/ ratio, the presulfiding material and the reaction temperature were made. Increases in the reaction rate caused by either changes in the catalyst composition or by moderate changes in the reaction temperature were compared to the catalyst coke content. It was suggested that two types of coke were present on the catalyst, a reactive coke which is subsequently converted to reaction products and an unreactive coke which blocks catalytic sites.

  18. Granulation of coke breeze fine for using in the sintering process

    Directory of Open Access Journals (Sweden)

    Mohamed F.M.

    2010-01-01

    Full Text Available Coke breeze is the main fuel used in the sintering process. The value of -3+1 mm. represents the most favorable particle size for coke breeze in the sintering process. About 20% of total coke fines (-0.5 mm are produced during different steps of preparation. Introducing these fines during the sintering process proves to be very harmful for different operating parameters. Thus ,this study aims at investigating the production of granules resulting from these fines using molasses as organic binder and its application in sintering of an iron ore. The results showed that the granules having the highest mechanical properties were obtained with 14.5 wt % molasses addition. The sintering experiments were performed by using coke breeze in different shapes (-3+1 mm in size, coke breeze without sieving and coke breeze granules -3+1 mm. The reduction experiments, microscopic structure and X-ray analysis for the produced sinter were carried out. The results revealed that, all sinter properties (such as shatter test, productivity of sinter machine and blast furnace, reduction time and chemical composition for produced sinter by using coke breeze with size -3+1 mm and coke breeze granules were almost the same. The iron ore sinter which was produced by using coke breeze without sieving yielded low productivity for both sinter machine and blast furnace. Furthermore, using coke breeze without sieving in sintering of an iron ore decreases the vertical velocity of sinter machine and increases the reduction time.

  19. 40 CFR 63.303 - Standards for nonrecovery coke oven batteries.

    Science.gov (United States)

    2010-07-01

    ... batteries. 63.303 Section 63.303 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.303 Standards for nonrecovery coke oven batteries... existing nonrecovery coke oven battery that exceed any of the following emission limitations or...

  20. Effects of Coke Calcination Level on Pore Structure in Carbon Anodes

    Science.gov (United States)

    Fang, Ning; Xue, Jilai; Lang, Guanghui; Bao, Chongai; Gao, Shoulei

    2016-02-01

    Effects of coke calcination levels on pore structure of carbon anodes have been investigated. Bench anodes were prepared by 3 types of cokes with 4 calcination temperatures (800°C, 900°C, 1000°C and 1100°C). The cokes and anodes were characterized using hydrostatic method, air permeability determination, mercury porosimetry, image analysis and confocal microscopy (CSLM). The cokes with different calcination levels are almost the same in LC values (19-20 Å) and real density (1.967-1.985 g/cm3), while the anode containing coke calcined at 900°C has the lowest open porosity and air permeability. Pore size distribution (represented by Anode H sample) can be roughly divided into two ranges: small and medium pores in diameter of 10-400 μm and large pores of 400-580 μm. For the anode containing coke calcined at 800°C, a number of long, narrow pores in the pore size range of 400-580 μm are presented among cokes particles. Formation of these elongated pores may be attributed to coke shrinkages during the anode baking process, which may develop cracking in the anode under cell operations. More small or medium rounded pores with pore size range of 10-400 μm emerge in the anodes with coke calcination temperatures of 900°C, 1000°C and 1100°C, which may be generated due to release of volatiles from the carbon anode during baking. For the anode containing coke calcined at 1100°C, it is found that many rounded pores often closely surround large coke particles, which have potential to form elongated, narrow pores.

  1. Assessment of thermal efficiency of heat recovery coke making

    Science.gov (United States)

    Tiwari, H. P.; Saxena, V. K.; Haldar, S. K.; Sriramoju, S. K.

    2017-08-01

    The heat recovery stamp charge coke making process is quite complicated due to the evolved volatile matter during coking, is partially combusted in oven crown and sole flue in a controlled manner to provide heat for producing metallurgical coke. Therefore, the control and efficient utilization of heat in the oven crown, and sole flue is difficult, which directly affects the operational efficiency. Considering the complexity and importance of thermal efficiency, evolution of different gases, combustion of gasses in oven crown and sole flue, and heating process of coke oven has been studied. A nonlinear regression methodology was used to predict temperature profile of different depth of coal cake during the coking. It was observed that the predicted temperature profile is in good agreement with the actual temperature profile (R2 = 0.98) and is validated with the actual temperature profile of other ovens. A complete study is being done to calculate the material balance, heat balance, and heat losses. This gives an overall understanding of heat flow which affects the heat penetration into the coal cake. The study confirms that 60% heat was utilized during coking.

  2. Polish scenery of coking industry activity

    International Nuclear Information System (INIS)

    Zielinski, H.

    1994-01-01

    The cooking industry in Poland and the world depends on conditions of iron and steel industry. Nowadays it is observed depression of this industry. On the other hand it is occurred a strong public pressure to reduce pollution by coking works. It is known that modernizing enterprises need a great deal of funds, but they are necessary, in order to keep coking industry on market. (author). 2 tabs

  3. Production of conductive coke for cathodic protection

    Energy Technology Data Exchange (ETDEWEB)

    Mogollon, E.G.; Henao, L.E.; Pacheco, L.A.; Ortiz, J.L.; Diaz, J.J. [Universidad Nacional de Colombia, Bogota (Colombia). Departamento de Quimica

    1999-07-01

    The reduction of resistivity of coke by means of the cocarbonization of mixtures of coking coals was studied using coal tar as an additive. Optimum temperature and blending conditions for decreased resistivity were investigated. The effect of particle size on the dependency of coal rank was investigated. 2 refs., 4 figs., 2 tabs.

  4. The new coke oven battery heating control system at Rautaruukki Steel

    Energy Technology Data Exchange (ETDEWEB)

    Palmu, P.; Swanljung, J. [Rautaruukki Steel, Raahe (Finland)

    1998-07-01

    The heating control system of the coke oven batteries has been developed strongly during the existence of the coke oven plant. The first step of the heating control was a statistical model which had a good monitoring system. This was enough in those days due to bigger problems elsewhere. The second generation heating control system is designed for irregular coke oven battery operation. Coke production in Rautaruukki Steel is based on one coke-oven plant consisting of two batteries and a by-product plant. The whole coke production is cooled by three dry quenching units. The first coke-oven battery was taken into operation in October 1987 and the second in November 1992. Originally the plant was mainly designed and equipped by Ukrainian Giprokoks except Finnish CDQ-boilers, German ammonia recovery process and electric and automation designed by Rautaruukki. Before building of the second coke oven battery, there was a huge amount of development and modification work to do, to ensure the proper function of the coke production. For example all electronic and hydraulic systems of the Russian supplier were replaced by systems designed by Rautaruukki's own personnel. When the coke production capacity was doubled, the only design by Gibrokoks related to the battery and one additional dry quenching chamber. The expansion project itself was managed and executed by Rautaruukki. The expansion project consisted of: the second battery, third CDQ-unit, Desulphurization and Benzol plants for the by-product plant and upgrading of automation system. Battery and CDQ chamber refractory materials were Russian origin and all other main equipment were purchased by Rautaruukki from western and domestic manufacturers based on the operation difficulties and experience of coke oven battery No. 1. These modification practices made a good basis for later development in the field of coke oven battery automation. The hierarchy of the coke oven battery automation at Rautaruukki Steel consist

  5. Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

    Energy Technology Data Exchange (ETDEWEB)

    Magdalena Zaharia; Veena Sahajwalla; Byong-Chul Kim; Rita Khanna; N. Saha-Chaudhury; Paul O' Kane; Jonathan Dicker; Catherine Skidmore; David Knights [University of New South Wales, Sydney, NSW (Australia). School of Materials Science and Engineering

    2009-05-15

    The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

  6. EPA Administrative Order on Consent (AOC) with ERP Compliant Coke, LLC

    Science.gov (United States)

    This Administrative Order on Consent with ERP Compliant Coke was effective August 2016. The Walter Coke facility located in North Birmingham was purchased by ERP Compliant Coke, LLC in February 2016 out of bankruptcy proceedings.

  7. Alternative method for assessing coking coal plasticity

    Energy Technology Data Exchange (ETDEWEB)

    Dzuy Nguyen; Susan Woodhouse; Merrick Mahoney [University of Adelaide (Australia). BHP Billiton Newcastle Technology Centre

    2008-07-15

    Traditional plasticity measurements for coal have a number of limitations associated with the reproducibility of the tests and their use in predicting coking behaviour. This report reviews alternative rheological methods for characterising the plastic behaviour of coking coals. It reviews the application of more fundamental rheological measurements to the coal system as well as reviewing applications of rheology to other physical systems. These systems may act as potential models for the application of fundamental rheological measurements to cokemaking. The systems considered were polymer melts, coal ash melts, lava, bread making and ice cream. These systems were chosen because they exhibit some physically equivalent processes to the processes occurring during cokemaking, eg, the generation of bubbles within a softened system that then resolidifies. A number of recommendations were made; the steady and oscillatory shear squeeze flow techniques be further investigated to determine if the measured rheology characteristics are related to transformations within the coke oven and the characteristics of resultant coke; modification of Gieseler plastometers for more fundamental rheology measurements not be attempted.

  8. Coking industry of China (conclusion of visit to People's Republic of China)

    Energy Technology Data Exchange (ETDEWEB)

    Sklyar, M.G. (NPO Koksokhimiya (USSR))

    1990-12-01

    Presents a report on the coking industry in China, in particular, research programs on coking. The report was prepared by Soviet specialists who visited China in March 1990 within the framework of an exchange program. The following aspects are discussed: characteristics of iron metallurgy and the coking industry in China, research institutes that specialize in problems of iron metallurgy and coking, main research programs of Chinese research institutes (development of a 12-category classification of black coal from China, coal preparation prior to coking including selective crushing, formed coke processes, quality of the products of bituminous coal coking, coal gasification and hydrogenation), installations used for research programs in China (delayed coking of black coal, hydrogenation of long-flame coal, coal briquetting), characteristics of selected coking plants in China, training for specialists in the coking industry in China.

  9. China's coke industry: Recent policies, technology shift, and implication for energy and the environment

    International Nuclear Information System (INIS)

    Huo, Hong; Lei, Yu; Zhang, Qiang; Zhao, Lijian; He, Kebin

    2012-01-01

    China is the largest coke producer in the world, accounting for over 60% of the world coke production, which makes the coke industry in China a significant coal consumer and air pollutant emitter. Recently, China has taken a series of measures to improve energy efficiency and reduce emissions from the coke industry, including eliminating old and low energy-efficiency coking technologies, promoting advanced technologies, and strengthening energy and environmental requirements on coking processes. As a consequence, China's coke industry is experiencing an unprecedented technology shift, which was characterized by the elimination of old, inefficient, and polluting indigenous ovens and small machinery ones within 10 years. This study examines the policies and the prompt technology shift in China's coke industry, as well as the associated energy and environmental effects, and discusses the implications with respect to the development of the coke industry in China towards a more efficient and clean future. As China sets stricter requirements on energy efficiency and the ambient environment, a more significant change focusing on technologies of energy saving and emission reduction is urgently needed at present. Those mature technologies, including coke dry quenching, coke oven gas recycle, fine particle removal, etc., should be enforced in the near future. - Highlights: ► With 60% of world coke output, China's coke making has big energy/pollution issues. ► Actions were taken to improve energy and environmental performance of coke plants. ► China's coke industry is experiencing an unprecedented technology shift. ► Another shift, focusing on technologies of energy and emission saving, is needed. ► More measurement studies on coking emissions are needed given the importance.

  10. Effect of nut coke on the performance of the ironmaking blast furnace

    NARCIS (Netherlands)

    Song, Q.

    2013-01-01

    The blast furnace consumes a large amount of high quality metallurgy coke (size 35-80 mm) in addition to ore in the form of pellets and sinter. This coke is the coarse fraction, derived from the coke plant. The fine fraction (8 -35 mm), arise after sieving, named nut coke, can’t be directly used in

  11. Enrichment of reactive macerals in coal: its characterization and utilization in coke making

    Science.gov (United States)

    Nag, Debjani; Kopparthi, P.; Dash, P. S.; Saxena, V. K.; Chandra, S.

    2018-01-01

    Macerals in coal are of different types: reactive and inert. These macerals are differ in their physical and chemical properties. Column flotation method has been used to separate the reactive macerals in a non-coking coal. The enriched coal is then characterized in order to understand the changes in the coking potential by different techniques. It is then used in making of metallurgical coke by proper blending with other coals. Enriched coal enhance the properties of metallurgical coke. This shows a path of utilization of non-coking coal in metallurgical coke making.

  12. Utilization coke dust as fuel in the cement industry

    International Nuclear Information System (INIS)

    Nawaz, S.

    2006-01-01

    Utilization of coke dust available from coal carbonization plants, as a fuel in the cement industry has been undertaken and discussed in this research paper. The parameters studied include physical and chemical evaluation of the coke dust and its economic feasibility/ suitability as fuel for the cement plants. Detailed studies have been carried out on the above referred parameters. In addition a comparative study has been done to access its suitability in comparison to other fuels especially imported coal. It has been found that the coke dust contained about 66% fixed carbon, 29% ash, 4% volatile matter, 1% moisture and 0.48% sulphur. It gross calorific value was found to be 5292 Kcal/kg. The detailed analysis of coke dust ash was also performed to determine as to how its constituents will compare with the cement constituents. Keeping in view the experimental results/ data generated on the coke dust, it has been concluded that it can be quite a good substitute for imported coal. In doing so a substantial financial saving can be achieved which ranges 40-45%. (author)

  13. Raising lump coke formation capacity of semicoking briquets in the Deuben briquetting plant

    Energy Technology Data Exchange (ETDEWEB)

    Naundorf, W.; Trommer, D.; Schroeder, H.-W.; Dressler, H.

    1988-01-01

    Describes brown coal briquetting and coking experiments aimed at producing high quality lumpy coke suitable for heating, metallurgy and other industrial processes. The Deuben coking and gas plant produces low temperature carbonization briquets from coal with 13.2% ash content, 54.8% volatiles, 13.5% semicoking tar with the effect that coke produced from these briquets disintegrates completely into fines (0/15 mm grain size). The study centered on effects of briquetting and coking parameters including coal grain size, coal moisture, briquetting pressure, coking temperature, heating rate and application of sulfite liquor as binder. Graphs of briquetting and coking results are provided. The Deuben coal was shown to be suitable for producing lumpy coke (11.5 to over 20 MPa compression strength) from coal under the optimum briquetting parameters of 0/1 mm grain size, 11% coal moisture, briquetting temperature of 70 to 80 C and briquetting pressure over 120 MPa. Use of a binder was found to be advantageous but not necessary. The produced coke showed favorable combustion properties. 6 refs.

  14. Prediction of coking dynamics for wet coal charge

    Directory of Open Access Journals (Sweden)

    Kardaś Dariusz

    2015-09-01

    Full Text Available A one-dimensional transient mathematical model describing thermal and flow phenomena during coal coking in an oven chamber was studied in the paper. It also accounts for heat conduction in the ceramic oven wall when assuming a constant temperature at the heating channel side. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. The histories of temperature, gas evolution and internal pressure were presented and analysed. The theoretical predictions of temperature change in the centre plane of the coke oven were compared with industrialscale measurements. Both, the experimental data and obtained numerical results show that moisture content determines the coking process dynamics, lagging the temperature increase above the water steam evaporation temperature and in consequence the total coking time. The phenomenon of internal pressure generation in the context of overlapping effects of simultaneously occurring coal transitions - devolatilisation and coal permeability decrease under plastic stage - was also discussed.

  15. The Release of Trace Elements in the Process of Coal Coking

    Directory of Open Access Journals (Sweden)

    Jan Konieczyński

    2012-01-01

    Full Text Available In order to assess the penetration of individual trace elements into the air through their release in the coal coking process, it is necessary to determine the loss of these elements by comparing their contents in the charge coal and in coke obtained. The present research covered four coke oven batteries differing in age, technology, and technical equipment. By using mercury analyzer MA-2 and the method of ICP MS As, Be, Cd, Co, Hg, Mn, Ni, Se, Sr, Tl, V, and Zn were determined in samples of charge coal and yielded coke. Basing on the analyses results, the release coefficients of selected elements were determined. Their values ranged from 0.5 to 94%. High volatility of cadmium, mercury, and thallium was confirmed. The tests have shown that although the results refer to the selected case studies, it may be concluded that the air purity is affected by controlled emission occurring when coke oven batteries are fired by crude coke oven gas. Fugitive emission of the trace elements investigated, occurring due to coke oven leaks and openings, is small and, is not a real threat to the environment except mercury.

  16. 40 CFR 63.302 - Standards for by-product coke oven batteries.

    Science.gov (United States)

    2010-07-01

    ... batteries. 63.302 Section 63.302 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... National Emission Standards for Coke Oven Batteries § 63.302 Standards for by-product coke oven batteries... oven emissions from each affected existing by-product coke oven battery that exceed any of the...

  17. Development of the super coke oven for productivity and environment enhancement toward the 21st century (SCOPE 21); Sekitan kodo tenkan cokes seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Nakashima, Y; Nishioka, K; Otsuka, J [The Japan Iron and Steel Federation, Tokyo (Japan)

    1996-09-01

    Serious shortage is predicted on cokes for blast furnaces in the first half of the 21st century. In order to deal flexibly with the fluid world market in the future, it is necessary to have a technology developed, by which coals from coking coal to non-coking dust coal can be used. The Japan Iron and Steel Federation and the Center for Coal Utilization, Japan are working on research and development of a new process with enhanced environmentality and economy (SCOPE 21) as a coke manufacturing process to respond to the requirements arisen from the above situation. The process is assessed basing on basic technological seeds such as rapid coal heating and high-speed carbonization and reformation of middle to low temperature cokes. The organizations are moving forward an eight-year development program which has started in fiscal 1994. This paper reports the summary of the development, and results of investigations and researches performed during fiscals 1994 and 1995. Rapid heating tests, middle to low temperature coke reformation tests, and tests for plug transportation of high-temperature coal have been performed. It has been verified, for example, that rapid coal heating can improve coke strength. The development work is being promoted toward grain size distribution and upscaling problems. 5 refs., 16 figs., 2 tabs.

  18. 77 FR 15123 - Foundry Coke From China; Scheduling of an Expedited Five-Year Review

    Science.gov (United States)

    2012-03-14

    ... submitted by ABC Coke, Erie Coke, Tonawanda Coke Corporation, and Walter Coke Co. to be individually... Analyst... Cynthia Foreso (205-3348). Attorney Charles St. Charles (205-2782). Supervisory Investigator...

  19. Pyrolisator Coal to be Cokes (Coal Cokes Casting Metal Industry Standard

    Directory of Open Access Journals (Sweden)

    Sukamto

    2016-01-01

    Full Text Available Pyrolisis of coal is partial combustion to reduce total moisture, volatile matter and sulfur contens and increase the calorific value of coal. The results of pyrolysis of coal is coke. At the laboratory level studies, pyrolisis done in batch using different calorie, namely 5800, 6000, 6300 kcal/kg and a time of 15-60 minutes and the temperature 400-800°C. Maximum results obtained total moisture (0.44%, fixed carbon (89%, volatile matter (2.4%, sulfur content (undetected and ash (7.2%. Then applied to the scale miniplant with continuous processes using multitube pyrolisator which are designed to operate in the temperature range 400-800°C and a flow rate of 240-730 kg/h, obtained coal cokes that meets industry quality standards, namely TM (0.42%, FC (90.40%, VM (2.16%, S (not detected, Ash (6.8% incalori 6300 kcal/h, a flow rate of 240 kg / h and temperatures between 600-700°C

  20. Modelling of Coke Layer Collapse during Ore Charging in Ironmaking Blast Furnace by DEM

    Science.gov (United States)

    Narita, Yoichi; Mio, Hiroshi; Orimoto, Takashi; Nomura, Seiji

    2017-06-01

    A technical issue in an ironmaking blast furnace operation is to realize the optimum layer thickness and the radial distribution of burden (ore and coke) to enhance its efficiency and productivity. When ore particles are charged onto the already-embedded coke layer, the coke layer-collapse phenomenon occurs. The coke layer-collapse phenomenon has a significant effect on the distribution of ore and coke layer thickness in the radial direction. In this paper, the mechanical properties of coke packed bed under ore charging were investigated by the impact-loading test and the large-scale direct shear test. Experimental results show that the coke particle is broken by the impact force of ore charging, and the particle breakage leads to weaken of coke-layer strength. The expression of contact force for coke in Discrete Element Method (DEM) was modified based on the measured data, and it followed by the 1/3-scaled experiment on coke's collapse phenomena. Comparing a simulation by modified model to the 1/3-scaled experiment, they agreed well in the burden distribution.

  1. The effect of high and low dissolved oxygen on the toxicity of oil sands coke and its leachate to Chironomus tentans

    International Nuclear Information System (INIS)

    Squires, A.J.; Liber, K.

    2003-01-01

    A study was conducted to assess the effect of low dissolved oxygen on the long-term leaching potential of the toxic constituents found in coke. Coke is one of the waste products produced during the oil sand upgrading process used at Syncrude Canada Ltd. and Suncor Energy Inc. Coke is contaminated by metals and organic compounds which can leach into the environment. In this study, coke from both companies was exposed to reconstituted water and high dissolved oxygen for a period of 30 days, during which time the overlying water containing the leachate and the coke pore-water was chemically analyzed. The benthic macroinvertebrate, Chironomus tentans, was exposed to the aged coke and the overlying leachate after the 30 day period. The study did not reveal any major difference in the survival or growth between the dissolved oxygen treatments or any of the leachate treatments. The macroinvertebrate in the aged Syncrude grew significantly while the Suncor coke strongly inhibited both survival and growth of the macroinvertebrate. The study demonstrates that coke has the potential to negatively affect benthic organisms if it is used uncovered in an aquatic reclamation effort

  2. Investigating combined influence of petrology and technological parameters on strength of porous coke body

    Energy Technology Data Exchange (ETDEWEB)

    Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

    1983-09-01

    The VUKhIN branch in Kuznetsk investigated effects of coal petrology and coking conditions on structural strength of coke in blast furnaces. Structural strength of coke produced from black coal from the Kuzbass as well as structural strength of coke partially gasified by carbon dioxide under conditions similar to those in blast furnaces was investigated. Fourteen samples of coal mixtures from the Kuzbass were used. Regression analysis was applied. Equations for forecasting coke properties on the basis of coal petrology and selected parameters characterizing coking were derived. Analyses showed that coke structural strength was decisively influenced by coefficients which characterized the average reflectivity of vitrinite in a coal mixture and its average density. After partial coke gasification by carbon dioxide effects of coefficients which characterized coal mixture nonhomogeneity (fluctuations of vitrinite reflectivity) and coal mixture density increased. Increasing coal density partially compensated negative effects of fluctuations of vitrinite reflectivity on coke structural strength. (10 refs.) (In Russian)

  3. Incorporation of petroleum coke into red ceramic; Incorporacao de coque de petroleo em ceramica vermelha

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, L.A. de; Monteiro, S.N.; Sanchez, R.; Vieira, C.M.F. [Laboratorio de Materiais Avancados - LAMAV, Universidade Estadual do Norte Fluminense Darcy Ribeiro - UENF, Campos dos Goytacazes, RJ (Brazil)], e-mails: sanchez@uenf.br, vieira@uenf.br

    2011-04-15

    This work has as its objective the evaluation of the effect of incorporation of petroleum coke in the physical and mechanical properties of red ceramic. Compositions were prepared with 0%, 1%, 2% and 4 wt.% of petroleum coke incorporated into a kaolinitic clayey body. Rectangular specimens were formed by extrusion to fire at 850 deg C and 1050 deg C. The determined physical and mechanical properties were flexural rupture strength and water absorption. The microstructure of the fired ceramics was evaluated by optical microscopy. The results show that the petroleum coke waste can significantly contribute to reduce the energy consumption during the firing stage. However, incorporations must be done in amounts around 1 wt.% to avoid deleterious effect on the water absorption of the ceramic. (author)

  4. New technological solutions in construction and operation of batteries with large coke ovens

    Energy Technology Data Exchange (ETDEWEB)

    Volokita, G.I.; Bulyga, N.I.

    1988-11-01

    Describes design modifications to the No. 7 coke oven battery with 7.0 m high coke ovens in the Avdeevka coking plant. Temperature distribution in the large coke ovens was irregular due to the specific design of the heating system, distribution and dimensions of flue channels and thickness of flue channel walls. During coke battery reconstruction length of the peripheral flue channels was reduced by 70 mm, coke oven volume was reduced from 41.6 to 41.3 m/sup 3/. These design changes resulted in a more regular temperature distribution and reduced temperature difference between the coke oven center and zones close to the machine and pusher sides. Thickness of flue channel walls was reduced from 130 to 105 mm. Special reinforcing elements that guarantee more regular temperature distribution and increased wall service life were used.

  5. Achievements and research programs of the Institute for Chemical Coal Processing in the field of conventional coking

    Energy Technology Data Exchange (ETDEWEB)

    Cieslar, R.; Kaziszyn, I.; Zawistowksi, J.

    1986-11-01

    This paper describes research programs of the Institute for Chemical Coal Processing in Zabrze on black coal coking and coke use in metallurgy from 1955 to 1990. In 1955-1970 the programs concentrated on coal mixture composition (selective crushing), optimization of coking conditions, mechanical coke treatment. In 1971-1980 research concentrated on coal preparation prior to coking and new coking systems for the Katowice steel plant (heat treatments, design of large coke ovens). The following research programs were implemented in 1981-1985: partial coal charge briquetting, production of foundry coke, coal charge preheating, production of blast furnace coke from black coal from Dobiensko, reducing coke consumption of blast furnaces. In 1986-1990 the Institute will concentrate on the following research programs: coal preparation schemes and coking schemes for coking low-quality weakly caking coals, optimization of coke oven design (e.g. use of packed charge), reducing coke consumption in metallurgy and heating systems, reducing air pollution from coking.

  6. Coke Formation During Hydrocarbons Pyrolysis. Part Two: Methane Thermal Cracking Formation de coke pendant la pyrolyse des hydrocarbures. Deuxième partie : pyrolyse du méthane

    Directory of Open Access Journals (Sweden)

    Billaud F.

    2006-11-01

    Full Text Available Part one of this article dealt with coking in a steam cracking furnace. In this process, coke deposition is a very complex phenomenon due to the number of parameters involved. Nevertheless, for this process, coke deposition is a secondary reaction which does not affect steam cracking yields. It is completely different for methane thermal cracking. Coke is one of the main products of this reaction. Part two of this article deals with coke deposition on the walls of the reactors used for methane thermal cracking. After a brief description of the different set-ups used to study coke deposition, the main parameters involved are listed. The importance of temperature, conversion, type of diluent, and hydrocarbon partial pressure will be enhanced. To conclude, two approaches to the mechanism are proposed to explain coke formation during methane thermal cracking. La première partie de cet article faisait le point sur les réactions indésirables de cokage dans les réacteurs de vapocraquage : dans le cadre de ce procédé, la formation de coke est un phénomène complexe du fait du nombre important de paramètres mis en jeu. Toutefois, pour ce procédé, la réaction de formation du coke à la paroi des réacteurs est une réaction secondaire qui n'affecte pas les rendements de vapocraquage. Ceci est complètement différent dans le cas de la pyrolyse thermique du méthane, procédé pour lequel le coke est un produit principal et indésirable de la réaction. La seconde partie de cet article est consacrée plus particulièrement à la formation du coke, lors de la pyrolyse du méthane et présente les principaux résultats expérimentaux décrits dans la littérature. Parmi les différents montages expérimentaux utilisés pour mesurer le dépôt de coke, il est mentionné, à partir des travaux de la littérature, les 2 techniques suivantes : - la technique de la paroi chaude, - la technique du fil chaud. Pour la première technique, les montages exp

  7. Dust emission from wet, low-emission coke quenching process

    Science.gov (United States)

    Komosiński, Bogusław; Bobik, Bartłomiej; Konieczny, Tomasz; Cieślik, Ewelina

    2018-01-01

    Coke plants, which produce various types of coke (metallurgical, foundry or heating), at temperatures between 600 and 1200°C, with limited access to oxygen, are major emitters of particulates and gaseous pollutants to air, water and soils. Primarily, the process of wet quenching should be mentioned, as one of the most cumbersome. Atmospheric pollutants include particulates, tar substances, organic pollutants including B(a)P and many others. Pollutants are also formed from the decomposition of water used to quench coke (CO, phenol, HCN, H2S, NH3, cresol) and decomposition of hot coke in the first phase of quenching (CO, H2S, SO2) [1]. The development of the coke oven technology has resulted in the changes made to different types of technological installations, such as the use of baffles in quench towers, the removal of nitrogen oxides by selective NOx reduction, and the introduction of fabric filters for particulates removal. The BAT conclusions for coke plants [2] provide a methodology for the measurement of particulate emission from a wet, low-emission technology using Mohrhauer probes. The conclusions define the emission level for wet quenching process as 25 g/Mgcoke. The conducted research was aimed at verification of the presented method. For two of three quench towers (A and C) the requirements included in the BAT conclusions are not met and emissions amount to 87.34 and 61.35 g/Mgcoke respectively. The lowest particulates emission was recorded on the quench tower B and amounted to 22.5 g/Mgcoke, therefore not exceeding the requirements.

  8. Combustion kinetics of the coke on deactivated dehydrogenation catalysts

    NARCIS (Netherlands)

    Luo, Sha; He, Songbo; Li, XianRu; Li, Jingqiu; Bi, Wenjun; Sun, Chenglin

    2015-01-01

    The coke combustion kinetics on the deactivated catalysts for long chain paraffin dehydrogenation was studied by the thermogravimetry and differential thermogravimetry (TG–DTG) technique. The amount and H/C mole ratio of the coke were determined by the TG and elemental analysis. And the

  9. Fatigue life estimation on coke drum due to cycle optimization

    Science.gov (United States)

    Siahaan, Andrey Stephan; Ambarita, Himsar; Kawai, Hideki; Daimaruya, Masashi

    2018-04-01

    In the last decade, due to the increasing demand of petroleum product, the necessity for converting the heavy oil are increasing. Thus, demand for installing coke drum in whole world will be increase. The coke drum undergoes the cyclic high temperature and suddenly cooling but in fact is not designed to withstand that kind of cycle, thus the operational life of coke drum is much shorter in comparison to other equipment in oil refinery. Various factors determine in order to improve reliability and minimize the down time, and it is found that the cycle optimization due to cycle, temperature, and pressure have an important role. From this research it is found that the fatigue life of the short cycle is decrease by a half compare to the normal cycle. It also found that in the preheating stage, the stress peak is far exceed the yield strength of coke drum material and fall into plastic deformation. This is happened because of the temperature leap in the preheating stage that cause thermal shock in the upper part of the skirt of the coke drum.

  10. Fundamentals of Delayed Coking Joint Industry Project

    Energy Technology Data Exchange (ETDEWEB)

    Volk Jr., Michael; Wisecarver, Keith D.; Sheppard, Charles M.

    2003-02-07

    The coking test facilities include three reactors (or cokers) and ten utilities. Experiments were conducted using the micro-coker, pilot-coker, and stirred-batch coker. Gas products were analyzed using an on-line gas chromatograph. Liquid properties were analyzed in-house using simulated distillation (HP 5880a), high temperature gas chromatography (6890a), detailed hydrocarbon analysis, and ASTM fractionation. Coke analyses as well as feedstock analyses and some additional liquid analyses (including elemental analyses) were done off-site.

  11. Characterization of core-drilled cokes in a working blast furnace

    Energy Technology Data Exchange (ETDEWEB)

    Shanning Dong; Nigel Paterson; Denis R. Dugwell; Rafael Kandiyoti [Imperial College London, London (United Kingdom). Dept. of Chemical Engineering

    2007-07-01

    A batch of tuyere-level core-drilled cokes, taken from a blast furnace working with coal injection has been characterized using a battery of analytical techniques. These included size exclusion chromatography (SEC), FT-Raman Spectroscopy (FT-RS) and X-ray Powder Diffraction (XRD). SEC tests on NMP-extracts of cokes taken from zones where temperatures were ca. 1500{sup o}C, showed the presence of heavy soot-like material (ca. 107-108 u apparent mass). By contrast, cokes in higher temperature zones (ca. 2000{sup o}C), only gave small amounts of extractable material with up to ca. 105 u apparent mass. The presence of soot-like material indicated the conversion-unfavoured locations at the tuyere-level. FT-Raman spectra of NMP-extracted cokes varied: the area ratios of D (at 1288-1295cm{sup -1}) to G (at ca. 1596cm{sup -1}) bands decreased as the exposure temperature increased. The random (r) fractions decreased with increasing exposure temperature, whereas, the graphitic (G) fractions increased whilst the defect (D) fraction showed a more complex variation with temperature. The latter is a likely indicator of graphitization of tuyere-level cokes in the blast furnace. The Raman spectral results were validated by XRD analyses of the demineralised and NMP-extracted cokes. Raceway coke possessed the largest crystalline dimensions and closest inter-layer spacing because it had encountered highest temperatures as well as iron catalysis. The combination of SEC and Raman spectrometry on core-drill samples has provided information relevant for maintaining stable operation in a blast-furnace operating with coal injection. 13 refs., 7 figs., 6 tabs.

  12. Enhanced specific capacitance of modified needle cokes by controlling oxidation treatment

    International Nuclear Information System (INIS)

    Yang, Sunhye; Kim, Ick-Jun; Choi, In-Sik; Soo Kim, Hyun; Tack Kim, Yu

    2010-01-01

    The electric double-layer performance of needle cokes can be affected by the morphology of structures. Hence, we introduce modified needle cokes by using simple oxidation treatment. The degree of graphitization with high specific capacitance is controlled by acid and heat treatment. The active sites of cokes are increased with increasing oxidation time. Dilute nitric acid (HNO 3 ) and sodium chlorate (NaClO 3 ) are used for the activation of cokes. In this case, the interlayer distance is dramatically increased from 3.5 to 8.9 A. The specific capacitances are 33 F g -1 and 30 F ml -1 , respectively, on a two-electrode system with a potential range of 0-2.5 V. The behaviors of double-layer capacitance are demonstrated by the charge-discharge process and the morphologies of modified needle cokes are analyzed by XRD, FE-SEM, BET and elemental analysis.

  13. Problems of new processes in coking industry discussed at the Scientific Council of the GKNT and the Section of Coking Industry of the Scientific and Technological Council of the Ministry of Iron and Steel Industry of the USSR

    Energy Technology Data Exchange (ETDEWEB)

    Ermolova, V.P.

    1983-03-01

    A report is given from the conference on new processes in the Soviet coking industry held in Moscow on 28-29 October 1982. The following papers were delivered: implementing research programs on new coking processes, new trends in coking plant design and construction in the 11th 5 year plan and in the time period until 1990, increasing efficiency of coking industry, research program of the Scientific Council in 1983. The report concentrates on new trends in coking plant design. Considering that the raw material basis of the Eastern regions of the USSR is poor in high quality coking coal the new coking processes and technologies should use weakly coking coal. The following schemes are discussed: heat treatments (especially useful in the case of black coal from the Kuzbass characterized by intensive fluctuations of petrology), selective crushing (schemes developed by the VUKhIN Institute), partial briquetting of coal mixtures (experiments carried out by the UKhIN in the Donbass in 1982). Other problems of coking such as development of new systems of smokeless fuel feeding to coke ovens, dry coke quenching, increasing capacity of coke chambers to 41.6 m/sup 3/, environmental protection in coking industry and production of special coke types from poor quality coal for metallurgy are also described.

  14. Advanced coking process control at Rautaruukki Steel

    Energy Technology Data Exchange (ETDEWEB)

    Ritamaki, O.; Luhtaniemi, H. [Rautaruukki Engineering (Finland)

    1999-12-01

    The paper presents the latest development of the Coking Process Management System (CPMS) at Raahe Steel. The latest third generation system is based on the previous system with the addition of fuzzy logic controllers. (The previous second generation system was based simultaneous feed forward and feedback control.) The system development has resulted in balanced coke oven battery heating, decreased variation in process regulation between shifts and increase of process information for operators. The economic results are very satisfactory. 7 figs.

  15. High coking value pitch

    Science.gov (United States)

    Miller, Douglas J.; Chang, Ching-Feng; Lewis, Irwin C.; Lewis, Richard T.

    2014-06-10

    A high coking value pitch prepared from coal tar distillate and has a low softening point and a high carbon value while containing substantially no quinoline insolubles is disclosed. The pitch can be used as an impregnant or binder for producing carbon and graphite articles.

  16. The influence of calcination on the physical and chemical properties of petroleum and mixed cokes

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, K; Syrek, H

    1980-01-01

    Freshly prepared petroleum and coal-petroleum cokes, before utilization for the production of various materials, are subjected to calcining--thermal treatment in a neutral or reducing atmosphere without the admission of air at less than or equal to 1400/sup 0/. During calcining, stabilization of the physical and chemical properties of the cokes takes place. The properties of the obtained coke depend chiefly on the calcining time and temperature. During calcining, volatile substances are removed almost completely from the coke; the coke density is increased, and its structure is put in order; the electrical conductivity is improved; the mechanical strength is increased; and the reactivity of the coke is decreased. Laboratory studies were conducted on calcining mixed coal-petroleum cokes of two grades at 1200, 1250, and 1300/sup 0/ for 2-6 h. In the calcining products the content of volatile substances, the ash content, S content, and density were determined. It was ascertained that calcining of mixed coal-petroleum cokes goes analogously to calcining of pure petroleum cokes. Raising the temperature and increasing the time of calcining has a substantial effect on improvement of coke physical and chemical properties. For high-quality coke, calcining is to be carried out at greater than or equal to 1300/sup 0/ for 4-6 h, for ordinary coke at > 1200/sup 0/ and greater than or equal to 4 h. The results are regarded as starting data for an industrial study of the calcining process.

  17. Effects and mechanistic aspects of absorbing organic compounds by coking coal.

    Science.gov (United States)

    Ning, Kejia; Wang, Junfeng; Xu, Hongxiang; Sun, Xianfeng; Huang, Gen; Liu, Guowei; Zhou, Lingmei

    2017-11-01

    Coal is a porous medium and natural absorbent. It can be used for its original purpose after adsorbing organic compounds, its value does not reduce and the pollutants are recycled, and then through systemic circulation of coking wastewater zero emissions can be achieved. Thus, a novel method of industrial organic wastewater treatment using adsorption on coal is introduced. Coking coal was used as an adsorbent in batch adsorption experiments. The quinoline, indole, pyridine and phenol removal efficiencies of coal adsorption were investigated. In addition, several operating parameters which impact removal efficiency such as coking coal consumption, oscillation contact time, initial concentration and pH value were also investigated. The coking coal exhibited properties well-suited for organics' adsorption. The experimental data were fitted to Langmuir and Freundlich isotherms as well as Temkin and Redlich-Peterson (R-P) models. The Freundlich isotherm model provided reasonable models of the adsorption process. Furthermore, the purification mechanism of organic compounds' adsorption on coking coal was analysed.

  18. Delayed coking studies on Athabasca bitumen and Cold Lake heavy oil

    Energy Technology Data Exchange (ETDEWEB)

    Govindhakannan, J.; Khulbe, C. [National Centre for Upgrading Technology, Devon, AB (Canada); Natural Resources Canada, Devon, AB (Canada). CanmetENERGY

    2009-07-01

    This poster highlighted the results of a study that quantified the delayed coking product yields of Athabasca bitumen and Cold Lake heavy oil. It also investigated the effect of operating pressure and feed rates on product yield and quality. The effect of pressure on conversion of sulphur and nitrogen was also examined. Experimental results revealed that the yield of liquid products decreases and the yields of coke and gases increase as the operating pressure increases. Sulphur and nitrogen conversions increase with increasing pressure. In this study, the yield and quality of delayed coking products were not influenced by the variation in feed rates. It was concluded that feed rate changes do not significantly affect the yield and quality of delayed coking products because the residual liquid and coke trapped in the coker drum reside there for a duration that approaches infinity, compared to much smaller average residence time for vapor-phase compounds. tabs., figs.

  19. Influence of thermal charge preparation on coke comminution under blast-furnace operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

    1983-09-01

    Reactions of coke in the blast furnace are determined mainly by the nature of the coke itself which depends on the coal properties, its preparation and the coking conditions. In the blast furnace the coke reacts with alkali and alkaline earth metals in the burden. Preheated coal charges were found to absorb far less sodium and potassium carbonates than a conventional moist charge over an equivalent period, due to the smaller pore volume available.

  20. Variation in mineral composition of coal during enrichment and coking

    Energy Technology Data Exchange (ETDEWEB)

    M.L. Ulanovskii; A.N. Likhenko [Ukrkoks Coke Producers' Association, Dnepropetrovsk (Ukraine)

    2009-06-15

    The parameters I{sub b} and B{sub b} used in developing an optimal coking-batch composition are determined from data on the chemical composition of the ash in Donetsk Basin and other coal. It is found that, when the ash content is reduced in deeper enrichment of coal with an increased content of fine pyrite, there will be accompanying increase in the Fe{sub 2}O{sub 3} content and decrease in the SiO{sub 2} content of the ash in lighter fractions. This increases I{sub b}. In other words, reducing the ash content of the coal is an unpromising means of increasing CRI and CSR of the coke produced. Three ash-containing elements (silicon, aluminum, and iron) are experimentally proven to transfer from coal to coke. Specific behavior of calcium, magnesium, alkali metals, and sulfur during coking.

  1. Graphitization of Coke and Its Interaction with Slag in the Hearth of a Blast Furnace

    Science.gov (United States)

    Li, Kejiang; Zhang, Jianliang; Liu, Yanxiang; Barati, Mansoor; Liu, Zhengjian; Zhong, Jianbo; Su, Buxin; Wei, Mengfang; Wang, Guangwei; Yang, Tianjun

    2016-04-01

    Coke reaction behavior in the blast furnace hearth has yet to be fully understood due to limited access to the high temperature zone. The graphitization of coke and its interaction with slag in the hearth of blast furnace were investigated with samples obtained from the center of the deadman of a blast furnace during its overhaul period. All hearth coke samples from fines to lumps were confirmed to be highly graphitized, and the graphitization of coke in the high temperature zone was convinced to start from the coke surface and lead to the formation of coke fines. It will be essential to perform further comprehensive investigations on graphite formation and its evolution in a coke as well as its multi-effect on blast furnace performance. The porous hearth cokes were found to be filled up with final slag. Further research is required about the capability of coke to fill final slag and the attack of final slag on the hearth bottom refractories since this might be a new degradation mechanism of refractories located in the hearth bottom.

  2. Carbon dioxide emission in hydrogen production technology from coke oven gas with life cycle approach

    Directory of Open Access Journals (Sweden)

    Burmistrz Piotr

    2016-01-01

    Full Text Available The analysis of Carbon Footprint (CF for technology of hydrogen production from cleaned coke oven gas was performed. On the basis of real data and simulation calculations of the production process of hydrogen from coke gas, emission indicators of carbon dioxide (CF were calculated. These indicators are associated with net production of electricity and thermal energy and direct emission of carbon dioxide throughout a whole product life cycle. Product life cycle includes: coal extraction and its transportation to a coking plant, the process of coking coal, purification and reforming of coke oven gas, carbon capture and storage. The values were related to 1 Mg of coking blend and to 1 Mg of the hydrogen produced. The calculation is based on the configuration of hydrogen production from coke oven gas for coking technology available on a commercial scale that uses a technology of coke dry quenching (CDQ. The calculations were made using ChemCAD v.6.0.2 simulator for a steady state of technological process. The analysis of carbon footprint was conducted in accordance with the Life Cycle Assessment (LCA.

  3. The reaction of Polish market to last year's changes on international coke and steel market

    Energy Technology Data Exchange (ETDEWEB)

    Czornik, G.; Gabriel, D. [Polski Koks S.A. (Poland)

    2004-07-01

    The presentation, outlined in 16 slides/overheads, discussed the following: Poland's position in the world market; the Polish coking industry and the world coke and steel industry; the reaction of Polish coke plants; the effect of the increase in coke prices; ownership changes in Poland's coking industry scenarios for the future; the role of Polski Koks in Poland's coking industry; and sales and exports of coke by Polski Koks.

  4. Binderless briquetting of some selected South African prime coking, blend coking and weathered bituminous coals and the effect of coal properties on binderless briquetting

    Energy Technology Data Exchange (ETDEWEB)

    Mangena, S.J. [Division of Mining Technology, CSIR, PO Box 395, Pretoria, 0001 (South Africa); du Cann, V.M. [Coal and Mineral Technologies (Pty) Ltd, SABS, PO Box 73656, Lynnwood Ridge, Pretoria, 0040 (South Africa)

    2007-07-02

    The binderless briquetting of some selected South African prime coking and blend coking coals, as well as the effects of weathering on the binderless briquetting of some inertinite-rich bituminous coals, were investigated in the laboratory. Selected properties of these coals were determined and the coals were briquetted at various moisture contents and pressures. Based on the results obtained in this study, binderless briquetting was found to be most successful in the cases of the fresh, vitrinite-rich coking and blend coking coals and satisfactory in the fresh inertinite-rich Witbank coals. However, the bonding process seemed to be adversely affected by weathering. The negative impact on bonding could be ameliorated to some extent by the presence of a significant kaolinite content when the percentage ash reports in the order of more than 15% (air-dry basis). It should, however, be noted that kaolinite may reduce the water resistance of the briquettes. (author)

  5. New processes in iron metallurgy discussed by the Coking Section of the Scientific Council of the Main Committee of Science and Technology of the USSR

    Energy Technology Data Exchange (ETDEWEB)

    Bukvareva, O.F.

    1991-02-01

    Discusses problems evaluated in October 1990 by the Section during the meeting devoted to research programs in the twelfth five-year plan, research and development of continuous coking methods, prospects for new coke quenching processes. Selected research programs, coordinated research programs and development programs as well as recommendations for future research programs are evaluated. The following research programs aimed at use of weakly caking and noncaking coals in the coking plants are evaluated: coal preheating and charging preheated mixtures to coke ovens, partial coal charge briquetting and equipment for coal briquetting, development of commercial systems for packing coal charges in coke ovens, production of formed coke for metallurgy, processes for coal gas cleaning (especially ammonia separation), development of systems for utilization of waste heat from dry coke quenching for coal charge preheating. Participation of individual research institutes in the programs is discussed. The most significant projects of individual institutes are discussed. Recommendations for research programs for the period 1991 to 1995 are made.

  6. A small-angle neutron scattering investigation of coke deposits on catalysts

    International Nuclear Information System (INIS)

    Acharya, D.R.; Hughes, R.; Allen, A.J.

    1990-01-01

    Small-angle neutron scattering (SANS) has been used to characterize a silica-alumina catalyst before and after coke deposition. The reaction used to deactivate the catalyst was the isomerization of xylenes. The results showed that, while most of the surface area in this type of catalyst resides in the ultrafine pores of diameters less than 1 nm occupying about 7% of the sample volume, there appears to be no coke deposition in these pores. The coke seems to coat the solid structures of 3.3-nm diameter which are of capillary shape. Such structures occupy about 6% of the sample volume. The coke was found to correspond to amonolayer of composition CH 0.3 with a density of 1660 kg/m 3

  7. Automatic combustion control of the ArcelorMittal Tubarao coke oven batteries

    Energy Technology Data Exchange (ETDEWEB)

    L. Barbosa de Oliveira Mello; C.-H. Sampaio Dandrea; G.-H. Marietto Goncalves; A. Estevao Torres; N.-L. Biccas

    2008-05-15

    The objective of the automatic combustion control is to guarantee the operational stability of the coke batteries based on the control of the coking time and consequently, minimize the reduction of useful life of the ovens. This control is guided by a mathematical model whose inputs are process variables and raw materials parameters and outputs are combustion parameters. Therefore, this paper will present the evolution of the performance of the burning process, providing a stability of the coking time.

  8. Health Effects of Petroleum Coke

    Science.gov (United States)

    Significant quantities of fugitive dust from pet coke storage and handling operations present a health risk. EPA’s research suggests that petcoke does not pose a different health risk than similar-sized particulate matter (PM10).

  9. Reuse and activation of petroleum coke to remove metals in water

    International Nuclear Information System (INIS)

    Cardona, Santiago

    2006-01-01

    In the investigation I am reused the coke generated in the refinancing of the petroleum. It was proposed to activate al coke with characteristics of a carbon activated commercial and subsequently to use it to remove silver and present mercury in water. The carbon activated produced and the carbon activated commercial, LQ1000, they were characterized with the norms ASTM, indicate of iodine, area superficial al blue of methylene and indicate of blue of methylene and the results were compared. Likewise in the process of adsorption, the process of adsorption itself model with the equations of Freundlich and Langmuir. The activation of the coke I am planned through a design of experiments four factorial. The 16 coals produced were submitted al process of adsorption silver and mercury by duplicate. The study I report al coke activated as better adsorbent than the LQ1000 and with a smaller cost of fabrication but with a smaller one area superficial that the commercial one. The results obtained permit to produce carbon activated from the coke but economic to compete with the commercial coals activate

  10. Surface structure and oxidation reactivity of oil sand coke particles

    Energy Technology Data Exchange (ETDEWEB)

    Fairbridge, C.; Palmer, A.D.; Ng, S.H.; Furimsky, E.

    1987-05-01

    Fractions of particles of varying mean diameter were isolated from coke obtained from the fluid coking of Athabasca bitumen. Correlations were established between the rate of oxygen sorption and the apparent surface area as measured by carbon dioxide adsorption. The rate of oxygen sorption, r/sub o/, could be related to particle radius, R, by r/sub o/ varying with R/sup D/ T over a range of particle size where D is the fractal dimension of the coke. The existence of such correlations may be related to the iterative processes which form the particles. 14 refs., 5 figs., 2 tabs.

  11. Precautionary measures in determining volatile matter in natural coke washability fractions

    Energy Technology Data Exchange (ETDEWEB)

    Ashok K. Singh; N.K. Shukla; S.K. Srivastava; D.D. Haldar; B.N. Roy; Mamta Sharma [Central Institute of Mining and Fuel Research, Dhanbad (India)

    2009-01-15

    Industrial utilization of heat-altered coal, especially natural coke derived from coking coal, has become a challenge. As such approximately 3,500 million tones (Mt) reserves of baked coals are available in different coalfields of India. In the present investigation, a natural coke sample (03 tone) was collected from a huge dump of seam XIV of Burragarh colliery under leasehold of Bharat Coking Coal Ltd., a subsidiary of Coal India Ltd., situated in Dhanbad district of Jharkhand state. It was observed that the volatile matter in the washability fractions of different size ranges (50 to 0.5 mm) at specific gravity 1.40 to 1.80 showed erratic distribution with respect to ash. To check the abnormality, the subsamples were subjected to microscopic (petrographic) study and chemical analysis including CO{sub 2} determination. The high concentration of CO{sub 2} is related to high concentration of carbonate minerals generated due to igneous intrusions in coal seams. Based on above observations, it was concluded that the volatile matter can be corrected through determined CO{sub 2} content in each fraction. Since efforts are being made to use natural coke in different industries such as steel, power, cement, carbon artifacts, etc., a careful investigation of volatile matter distribution in natural coke washability fractions would be of immense help in planning its bulk use.

  12. Distillation of tar and tar fractions in the presence of surface-active coke

    Energy Technology Data Exchange (ETDEWEB)

    Jaeppelt, A; Klaus, J

    1943-01-01

    The tar obtained by low-temperature carbonization of Upper Silesian gas coke and fractions from this tar were distilled in the presence of different grades of coke dust with varying surface activity; the coke had been activated by steam in the course of its production by low-temperature carbonization. The surface activity of the coke dusts was measured by determining the heat of wetting with C/sub 6/H/sub 6/. Tar and coke dust, both anhydrous, were mixed in a kneading machine in such proportions that the capillaries of the dust were saturated and enough ''externally'' bound tar was present to permit briquetting. The briquets were distilled without cracking and with steam as heating medium. The yield and quality of the distillate depended on the magnitude of the internal surface of the coke dust used; a mixture of a very active coke from brown coal and tar yielded a distillate with Conradson carbon residue of 1.34 percent, asphalt content 6.1 percent and eta/sub 20/ 5.4/sup 0/ E. as compared with C residue of 10.95 percent, asphalt content 33.5 percent and eta/sub 20/ 123.6/sup 0/ E. of the distillate obtained in the absence of surface-active coke. Even higher-boiling fractions can be improved by this treatment, although it is preferable to use oils with an initial boiling point below 300/sup 0/. The ratio of oil to adsorbent is not critical, but better results were obtained with higher percentages of added coke dust. The process in its present form is not suited for the conversion of crude creosote to useful phenols.

  13. The coke formation during the pyrolysis of 1,2-dichloroethane - results of radiotracer experiments

    International Nuclear Information System (INIS)

    Kopinke, F.D.; Zychlinski, W.; Rodewald, D.

    1990-01-01

    The formation of coke-like deposits during the pyrolysis of dichloroethane has been investigated by means of 14 C-labelled compounds. Starting from industrial feedstocks coke is formed from dichloroethane and its primary reaction products as well as from trace impurities with comparable rates. Chloroprene has been revealed as an effective coke precursor. The coke formation from industrial feedstocks can be reduced significantly by suitable purification methods. (author)

  14. Denitrification of coking wastewater with micro-electrolysis.

    Science.gov (United States)

    Lv, Yanli; Wang, Yanqiu; Shan, Mingjun; Shen, Xue; Su, Ying

    2011-06-01

    The denitrification for the coking wastewater was conducted by means of original battery principle with Fe-C micro-electrolysis. Fe-C serves as positive and negative electrodes, by which N02(-)-N and TN were reduced to nitrogen, and then the purpose of denitrifieation for coking wastewater was realized. The influences of pH value, carbon particle size, Fe/C ratio (mass ratio), reaction time and coagulation pH value on removal rate of N02(-)-N and TN were investigated. Coking wastewater originated from Jiamusi Coal Chemistry Engineering Company. The optimum conditions of treatment were as follows: the initial pH was 3.0, the dosage of Fe 73.5 g/L, reaction time 70 min, mass ratio of Fe/C ratio 1.0:1.3, coagulation pH 9.0 and sedimentation time 40 min. Under those conditions, nitrogen removal efficiencies of N02(-)-N and TN were beyond 50% and 45%, respectively. Copyright © 2011 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  15. Dry purification of aspirational air in coke-sorting systems with wet slaking of coke

    Energy Technology Data Exchange (ETDEWEB)

    T.F. Trembach; A.G. Klimenko [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Coke transportation after wet slaking is accompanied by the release of dust in the production building and in the surrounding atmosphere. Wet methods are traditionally used to purify very humid air. Giprokoks has developed designs for highly efficient dry dust-removal methods in such conditions.

  16. Effects of Two-stage Heat Treatment on Delayed Coke and Study of Their Surface Texture Characteristics

    Science.gov (United States)

    Im, Ui-Su; Kim, Jiyoung; Lee, Seon Ho; Lee, Byung-Rok; Peck, Dong-Hyun; Jung, Doo-Hwan

    2017-12-01

    In the present study, surface texture features and chemical properties of two types of cokes, made from coal tar by either 1-stage heat treatment or 2-stage heat treatment, were researched. The relationship between surface texture characteristics and the chemical properties was identified through molecular weight distribution, insolubility of coal tar, weight loss with temperature increase, coking yield, and polarized light microscope analysis. Rapidly cleared anisotropy texture in cokes was observed in accordance with the coking temperature rise. Quinoline insolubility and toluene insolubility of coal tar increased with a corresponding increases in coking temperature. In particular, the cokes produced by the 2-stage heat treatment (2S-C) showed surface structure of needle cokes at a temperature approximately 50°C lower than the 1-stage heat treatment (1S-C). Additionally, the coking yield of 2S-C increased by approximately 14% in comparison with 1S-C.

  17. Coke battery with 51-m{sup 3} furnace chambers and lateral supply of mixed gas

    Energy Technology Data Exchange (ETDEWEB)

    V.I. Rudyka; N.Y. Chebotarev; O.N. Surenskii; V.V. Derevich [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    The basic approaches employed in the construction of coke battery 11A at OAO Magnitogorskii Metallurgicheskii Kombinat are outlined. This battery includes 51.0-m{sup 3} furnaces and a dust-free coke-supply system designed by Giprokoks with lateral gas supply; it is heated exclusively by low-calorific mixed gas consisting of blast-furnace gas with added coke-oven gas. The 82 furnaces in the coke battery are divided into two blocks of 41. The gross coke output of the battery (6% moisture content) is 1140000 t/yr.

  18. Record coking coal settlements

    Energy Technology Data Exchange (ETDEWEB)

    Macdonald, C.

    2005-02-01

    The US$100/tonne psychological barrier in coking coal prices has been well and truly smashed. The article examines developments in coal pricing. It includes quotes from many senior executives in the coal industry as collected at McCloskey's Australian Coal.04 conference held in Sydney, 18-19 November 2004. 2 photos.

  19. Investigation on treatment of cyanide in waste water of coke-oven plant with radiation-technique

    International Nuclear Information System (INIS)

    Qi Shengchu; He Yongke; Wu Jilan

    1992-01-01

    The treatment of cyanide in waste water of coke-oven plant with radiation-technique was investigated. The investigation indicated that toxic products under γ-ray irradiation were changed into less-toxic or non-toxic products. Organic pollutants will compete with cyanide for scavenging active intermediates of water (H, e aq - and OH radical). Therefore, it will inhibit cyanide radiolysis. The pretreatment with active carbon increases the radiolytic decomposition rate of cyanide and damage rate of organism in waste water. H 2 O 2 and N 2 O convert e aq - into OH radical. however they improve the efficiency decomposition of cyanide. OH radical plays an important role in reducing cyanide content and COD value

  20. Combined XRD and Raman studies of coke types found in SAPO-34 after methanol and propene conversion

    DEFF Research Database (Denmark)

    Wragg, David S.; Grønvold, Arne; Voronov, Alexey

    2013-01-01

    oligomerisation (PO) reactions. The coke caused by MTO leads to two distinct sets of HRPD peaks which can be indexed by two SAPO-34 unit cells with different lattice parameters and coke contents. We believe that these unit cells represent different zones of the catalyst filled with different coke types. PO coking...... does not lead to splitting of the diffraction peaks. Raman spectra show differences between the coke types produced by MTO and PO with the same overall trend of increasingly polyaromatic coke with increasing coke mass. The intensity of the monocyclic and polyaromatic peaks in the MTO Raman spectra...... correspond to the phase fractions of the two cell types used in the Rietveld refinement, suggesting a link between the two phases and the two coke types. The PO Raman spectra have a stronger polyaromatic band at low coke, suggesting that polyaromatics form faster. In situ powder XRD studies suggest...

  1. Discrete Element Method Modeling of the Rheological Properties of Coke/Pitch Mixtures.

    Science.gov (United States)

    Majidi, Behzad; Taghavi, Seyed Mohammad; Fafard, Mario; Ziegler, Donald P; Alamdari, Houshang

    2016-05-04

    Rheological properties of pitch and pitch/coke mixtures at temperatures around 150 °C are of great interest for the carbon anode manufacturing process in the aluminum industry. In the present work, a cohesive viscoelastic contact model based on Burger's model is developed using the discrete element method (DEM) on the YADE, the open-source DEM software. A dynamic shear rheometer (DSR) is used to measure the viscoelastic properties of pitch at 150 °C. The experimental data obtained is then used to estimate the Burger's model parameters and calibrate the DEM model. The DSR tests were then simulated by a three-dimensional model. Very good agreement was observed between the experimental data and simulation results. Coke aggregates were modeled by overlapping spheres in the DEM model. Coke/pitch mixtures were numerically created by adding 5, 10, 20, and 30 percent of coke aggregates of the size range of 0.297-0.595 mm (-30 + 50 mesh) to pitch. Adding up to 30% of coke aggregates to pitch can increase its complex shear modulus at 60 Hz from 273 Pa to 1557 Pa. Results also showed that adding coke particles increases both storage and loss moduli, while it does not have a meaningful effect on the phase angle of pitch.

  2. Coke detection in furnaces tubes by radiographic examination

    International Nuclear Information System (INIS)

    Santos, I.S. dos

    1987-01-01

    The coke detection technique by radiographic examinations allows to quantify the coke in furnace coils of Petroleum refineries and petrochemical industries. The paper describes how was determined the radiographic parameters, the wall apparent thickness calculation, the distance source-film, the position of the source and films, the chosen of films and the calculation of exposure time, aiming to obtain high producticity and good quality image. This technique is being used and improved for more than two years with good results. (E.G.) [pt

  3. Electrical conductivity of the screening residuals of coke production in context of ferrochromium production in a submerged arc furnace

    Energy Technology Data Exchange (ETDEWEB)

    Rousu, Arto; Mattila, Olli [Lab. of Process Metallurgy, Univ. of Oulu (Finland)

    2009-11-15

    Coke is used as a reducing agent in the production of ferrochromium in a submerged arc furnace (SAF). Its good electrical conductivity compared to other input materials makes it a dominant current conductivity substance in the burden. The resistance of the coke has to be high enough to ensure the proper functionality of the furnace. Used cokes for submerged arc furnace production are relatively small in size compared to e.g. blast furnace (BF) cokes. A common practice is to use screening residual coke, which is too small for the BF, in SAF. The goal of this study was to show differences in the electrical properties of screening residual cokes compared to coke formed in different parts of the coke battery, in dependence of particle size. The resistances of different cokes were measured and XRD measurements were performed to define the crystallographic structure of the selected cokes. The results indicate that small coke particles have higher overall resistance, which is due to their internal properties. This small weakly carbonized coke is formed in the middle of the coking battery and is subject to changes in varying coking practices. Continuous quality control of screening residual coke is needed to use it in the SAF. (orig.)

  4. Steam versus coking coal and the acid rain program

    International Nuclear Information System (INIS)

    Lange, Ian

    2010-01-01

    The Clean Air Act of 1990 initiated a tradable permit program for emissions of sulfur dioxide from coal-fired power plants. One effect of this policy was a large increase in the consumption of low-sulfur bituminous coal by coal-fired power plants. However, low-sulfur bituminous coal is also the ideal coking coal for steel production. The analysis presented here will attempt to determine how the market responded to the increased consumption of low-sulfur bituminous coal by the electricity generation sector. Was there a decrease in the quality and/or quantity of coking coal consumption or did extraction increase? Most evidence suggests that the market for coking coal was unaffected, even as the extraction and consumption of low-sulfur bituminous coal for electricity generation increased substantially.

  5. The impact of multiphase behaviour on coke deposition in heavy oil hydroprocessing catalysts

    Science.gov (United States)

    Zhang, Xiaohui

    Coke deposition in heavy oil catalytic hydroprocessing remains a serious problem. The influence of multiphase behaviour on coke deposition is an important but unresolved question. A model heavy oil system (Athabasca vacuum bottoms (ABVB) + decane) and a commercial heavy oil hydrotreating catalyst (NiMo/gamma-Al 2O3) were employed to study the impact of multiphase behaviour on coke deposition. The model heavy oil mixture exhibits low-density liquid + vapour (L1V), high-density liquid + vapour (L2V), as well as low-density liquid + high-density liquid + vapour (L1L2V) phase behaviour at a typical hydroprocessing temperature (380°C). The L2 phase only arises for the ABVB composition range from 10 to 50 wt %. The phase behaviour undergoes transitions from V to L2V, to L1L2V, to L1V with increasing ABVB compositions at the pressure examined. The addition of hydrogen into the model heavy oil mixtures at a fixed mass ratio (0.0057:1) does not change the phase behaviour significantly, but shifts the phase regions and boundaries vertically from low pressure to high pressure. In the absence of hydrogen, the carbon content, surface area and pore volume losses for catalyst exposed to the L1 phase are greater than for the corresponding L2 phase despite a higher coke precursor concentration in L2 than in L1. By contrast, in the presence of hydrogen, the carbon content, surface area and pore volume losses for the catalyst exposed to the L2 phase are greater than for the corresponding L1 phase. The higher hydrogen concentration in L1 appears to reverse the observed results. In the presence of hydrogen, L2 was most closely associated with coke deposition, L1 less associated with coke deposition, and V least associated with coke deposition. Coke deposition is maximized in the phase regions where the L2 phase arises. This key result is inconsistent with expectation and coke deposition models where the extent of coke deposition, at otherwise fixed reaction conditions, is asserted to

  6. Demand outlook for sulfur and high-sulfur petroleum coke

    Energy Technology Data Exchange (ETDEWEB)

    Koshkarov, V.Ya.; Danil' yan, P.G.; Feotov, V.E.; Gimaev, R.N.; Koshkarova, M.E.; Sadykova, S.R.; Vodovichenko, N.S.

    1980-01-01

    The feasibility of using sulfur and high-sulfur petroleum coke fines in pyrometallurgical processes and also in the chemical and coal-tar chemical industry is examined. Results of industrial tests on briquetting fines of petroleum coke with a petroleum binder are presented. The feasibility of using the obtained briquets in shaft furnace smelting of oxidized nickel ores, production of anode stock, and also in the chemical industry are demonstrated.

  7. Combined effects of petrographic and technological parameters on strength of porous coke substance

    Energy Technology Data Exchange (ETDEWEB)

    Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

    1983-09-01

    The proportion of coke in modern blast furnaces has been reduced and at the same time ore burdens have increased. The coke itself now derives from a much wider range of coals. Laboratory tests related to the structural strength of cokes were carried out with charges composed of 14 representative coals. Results showed that vitrinite reflectance and bulk density were the critical parameters, followed by petrographic composition. Increasing bulk density of the charge from 0.6 to 0.9 g/cm/sup 3/ produces coke with a structural strength which counteracts the effects of increasing diversity in both petrography and reflectance in any one charge.

  8. Investigations on high temperature coking of lignite with the help of radionuclide techniques

    International Nuclear Information System (INIS)

    Koennecke, H.G.; Luther, D.; Abendroth, H.C.

    1986-01-01

    The time characteristics and the varying flow characteristics of fine-grained briquettes during the high temperature coking of lignite according to Rammler and Bilkenroth were studied with the help of radionuclide technique. The process parameters (tsub(V), zsub(R), etc.) refer to the different zones of the coke furnace (bunker/dryer, coker/cooler). The different time charakteristics of the coke-grain fractions formed during the BHT-process enables a correlation of the retention time and the quality factors of the coke. The results obtained would enable a better operation of the individual furnaces in the plant and offer the basis for further process developments. (orig.) [de

  9. Discrete Element Method Modeling of the Rheological Properties of Coke/Pitch Mixtures

    Directory of Open Access Journals (Sweden)

    Behzad Majidi

    2016-05-01

    Full Text Available Rheological properties of pitch and pitch/coke mixtures at temperatures around 150 °C are of great interest for the carbon anode manufacturing process in the aluminum industry. In the present work, a cohesive viscoelastic contact model based on Burger’s model is developed using the discrete element method (DEM on the YADE, the open-source DEM software. A dynamic shear rheometer (DSR is used to measure the viscoelastic properties of pitch at 150 °C. The experimental data obtained is then used to estimate the Burger’s model parameters and calibrate the DEM model. The DSR tests were then simulated by a three-dimensional model. Very good agreement was observed between the experimental data and simulation results. Coke aggregates were modeled by overlapping spheres in the DEM model. Coke/pitch mixtures were numerically created by adding 5, 10, 20, and 30 percent of coke aggregates of the size range of 0.297–0.595 mm (−30 + 50 mesh to pitch. Adding up to 30% of coke aggregates to pitch can increase its complex shear modulus at 60 Hz from 273 Pa to 1557 Pa. Results also showed that adding coke particles increases both storage and loss moduli, while it does not have a meaningful effect on the phase angle of pitch.

  10. Geochemical characteristics of oil sands fluid petroleum coke

    International Nuclear Information System (INIS)

    Nesbitt, Jake A.; Lindsay, Matthew B.J.; Chen, Ning

    2017-01-01

    The geochemical characteristics of fluid petroleum coke from the Athabasca Oil Sands Region (AOSR) of northern Alberta, Canada were investigated. Continuous core samples were collected to 8 m below surface at several locations (n = 12) from three coke deposits at an active oil sands mine. Bulk elemental analyses revealed the coke composition was dominated by C (84.2 ± 2.3 wt%) and S (6.99 ± 0.26 wt%). Silicon (9210 ± 3000 mg kg"−"1), Al (5980 ± 1200 mg kg"−"1), Fe (4760 ± 1200 mg kg"−"1), and Ti (1380 ± 430 mg kg"−"1) were present in lesser amounts. Vanadium (1280 ± 120 mg kg"−"1) and Ni (230 ± 80 mg kg"−"1) exhibited the highest concentrations among potentially-hazardous minor and trace elements. Sequential extractions revealed potential for release of these metals under field-relevant conditions. Synchrotron powder X-ray diffraction revealed the presence of Si and Ti oxides, organically-complexed V and hydrated Ni sulfate, and provided information about the asphaltenic carbon matrix. X-ray absorption near edge structure (XANES) spectroscopy at the V and Ni K-edges revealed that these metals were largely hosted in porphyrins and similar organic complexes throughout coke grains. Minor differences among measured V and Ni K-edge spectra were largely attributed to slight variations in local coordination of V(IV) and Ni(II) within these organic compounds. However, linear combination fits were improved by including reference spectra for inorganic phases with octahedrally-coordinated V(III) and Ni(II). Sulfur and Fe K-edge XANES confirmed that thiophenic coordination and pyritic-ilmenitic coordination are predominant, respectively. These results provide new information on the geochemical and mineralogical composition of oil sands fluid petroleum coke and improve understanding of potential controls on associated water chemistry. - Highlights: • Oil sands fluid petroleum coke contains wide range of major, minor and

  11. Adsorption of organic pollutants from coking and papermaking wastewaters by bottom ash.

    Science.gov (United States)

    Sun, Wei-ling; Qu, Yan-zhi; Yu, Qing; Ni, Jin-ren

    2008-06-15

    Bottom ash, a power plant waste, was used to remove the organic pollutants in coking wastewater and papermaking wastewater. Particular attention was paid on the effect of bottom ash particle size and dosage on the removal of chemical oxygen demand (COD). UV-vis spectra, fluorescence excitation-emission matrix (FEEM) spectra, Fourier transform infrared (FTIR) spectra, and scanning electron microscopic (SEM) photographs were investigated to characterize the wastewaters and bottom ash. The results show that the COD removal efficiencies increase with decreasing particle sizes of bottom ash, and the COD removal efficiency for coking wastewater is much higher than that for papermaking wastewater due to its high percentage of particle organic carbon (POC). Different trends of COD removal efficiency with bottom ash dosage are also observed for coking and papermaking wastewaters because of their various POC concentrations. Significant variations are observed in the FEEM spectra of wastewaters after treatment by bottom ash. New excitation-emission peaks are found in FEEM spectra, and the fluorescence intensities of the peaks decrease. A new transmittance band in the region of 1400-1420 cm(-1) is observed in FTIR spectra of bottom ash after adsorption. The SEM photographs reveal that the surface of bottom ash particles varies evidently after adsorption.

  12. Adsorption of organic pollutants from coking and papermaking wastewaters by bottom ash

    International Nuclear Information System (INIS)

    Sun Weiling; Qu Yanzhi; Yu Qing; Ni Jinren

    2008-01-01

    Bottom ash, a power plant waste, was used to remove the organic pollutants in coking wastewater and papermaking wastewater. Particular attention was paid on the effect of bottom ash particle size and dosage on the removal of chemical oxygen demand (COD). UV-vis spectra, fluorescence excitation-emission matrix (FEEM) spectra, Fourier transform infrared (FTIR) spectra, and scanning electron microscopic (SEM) photographs were investigated to characterize the wastewaters and bottom ash. The results show that the COD removal efficiencies increase with decreasing particle sizes of bottom ash, and the COD removal efficiency for coking wastewater is much higher than that for papermaking wastewater due to its high percentage of particle organic carbon (POC). Different trends of COD removal efficiency with bottom ash dosage are also observed for coking and papermaking wastewaters because of their various POC concentrations. Significant variations are observed in the FEEM spectra of wastewaters after treatment by bottom ash. New excitation-emission peaks are found in FEEM spectra, and the fluorescence intensities of the peaks decrease. A new transmittance band in the region of 1400-1420 cm -1 is observed in FTIR spectra of bottom ash after adsorption. The SEM photographs reveal that the surface of bottom ash particles varies evidently after adsorption

  13. Thermal expansion of coking coals

    Energy Technology Data Exchange (ETDEWEB)

    Orlik, M.; Klimek, J. (Vyzkumny a Zkusebni Ustav Nova Hut, Ostrava (Czechoslovakia))

    1992-12-01

    Analyzes expansion of coal mixtures in coke ovens during coking. Methods for measuring coal expansion on both a laboratory and pilot plant scale are comparatively evaluated. The method, developed, tested and patented in Poland by the Institute for Chemical Coal Processing in Zabrze (Polish standard PN-73/G-04522), is discussed. A laboratory device developed by the Institute for measuring coal expansion is characterized. Expansion of black coal from 10 underground mines in the Ostrava-Karvina coal district and from 9 coal mines in the Upper Silesia basin in Poland is comparatively evaluated. Investigations show that coal expansion reaches a maximum for coal types with a volatile matter ranging from 20 to 25%. With increasing volatile matter in coal, its expansion decreases. Coal expansion increases with increasing swelling index. Coal expansion corresponds with coal dilatation. With increasing coal density its expansion increases. Coal mixtures should be selected in such a way that their expansion does not cause a pressure exceeding 40 MPa. 11 refs.

  14. Microwave-assisted grinding of metallurgical coke; Molienda asistida con microondas de un coque metalurgico

    Energy Technology Data Exchange (ETDEWEB)

    Ruisanchez, E.; Juarez-Perez, E. J.; Arenillas, A.; Bermudez, J. M.; Menendez, J. A.

    2014-10-01

    Metallurgical cokes are composed of graphitic carbon (s2p2) and different inorganic compounds with very different capacities to absorb microwave radiation. Moreover, due to the electric conductivity shown by the metallurgical cokes, microwave radiation produces electric arcs or microplasmas, which gives rise to hot spots. Therefore, when these cokes are irradiated with microwaves some parts of the particle experiment a rapid heating, while some others do not heat at all. As a result of the different expansion and stress caused by thermal the shock, small cracks and micro-fissures are produced in the particle. The weakening of the coke particles, and therefore an improvement of its grind ability, is produced. This paper studies the microwave-assisted grinding of metallurgical coke and evaluates the grinding improvement and energy saving. (Author)

  15. Coking coal of Checua Lenguazaque area

    International Nuclear Information System (INIS)

    Arboleda Otalora, Carlos Ariel

    1987-06-01

    In this report a summary of the main characteristics of the coal of the area of Checua-Samaca is presented. Using the main works carried out on this area, the most important geologic, physical-chemical, technological and petrographic aspects are compiled that are considered essential to carry out a technical evaluation of these coal and all the analyses they take to conclude that in this area, bituminous coal are presented with very good coking properties, on the other hand, it is demonstrated by the use that is given to the coal extracted by the small existent mining. However, keeping in mind the demands of the international market of the coking coal, it becomes necessary to improve the existent geologic information to be able to make reliable stratigraphic correlations

  16. Analysis of gas-phase mercury sorption with coke and lignite dust

    Directory of Open Access Journals (Sweden)

    Marczak Marta

    2017-01-01

    Full Text Available In recent years the problem of mercury emission became a widely discussed topic. Its high impact is caused by its toxicity and ability to accumulate in living organisms, properties that justified the United States Environmental Protection Agency (US EPA to classify mercury as hazardous pollutant. The problem of mercury emission is crucial for countries like Poland, where the most of the emission is caused by coaldepended energy sector. Current technology of mercury removal utilizes adsorption of mercury on the surface of activated carbon. Due to high price of activated carbon, this technological approach seems to be uneconomical and calls for cheaper alternative. One possible solution can be usage of other sorptive materials obtained from thermal processes like coke production. Example of such material is coke dust obtained from dry quenching of coke. The aim of this work was to analyse the sorption potential of lignite and coke dust and determine parameters influencing mercury behaviour during combustion.

  17. The effect of calcination conditions on the graphitizability of novel synthetic and coal-derived cokes

    Science.gov (United States)

    Bennett, Barbara Ellen

    The effects of calcination heating rate and ultimate calcination temperature upon calcined coke and subsequent graphitic material microstructures were studied for materials prepared from three different precursors. The pitch precursors used were Mitsubishi AR pitch (a synthetic, 100% mesophase pitch), the NMP-extracted portion of a raw coal, and the NMP-extracted fraction of a coal liquefaction residue obtained from an HTI pilot plant. These materials were all green-coked under identical conditions. Optical microscopy confirmed that the Mitsubishi coke was very anisotropic and the HTI coke was nearly as anisotropic. The coke produced from the direct coal extract was very isotropic. Crystalline development during calcination heating was verified by high-temperature x-ray diffraction. Experiments were performed to ascertain the effects of varying calcination heating rate and ultimate temperature. It was determined that calcined coke crystallite size increased with increasing temperature for all three materials but was found to be independent of heating rate. The graphene interplanar spacing decreased with increasing temperature for the isotropic NMP-extract material but increased with increasing temperature for the anisotropic materials---Mitsubishi and HTI cokes. Graphene interplanar spacing was also found to be independent of heating rate. Calcined coke real densities were, likewise, found to be independent of heating rate. The anisotropic cokes (Mitsubishi and HTI) exhibited increasing real density with increasing calcination temperature. The NMP-extract coke increased in density up to 1050°C and then suffered a dramatic reduction in real density when heated to 1250°C. This is indicative of puffing. Since there was no corresponding disruption in the crystalline structure, the puffing phenomena was determined to be intercrystalline rather than intracrystalline. After the calcined cokes were graphitized (under identical conditions), the microstructures were re

  18. Repair of walls of coke ovens with a volume of 41. 6 m/sup 3/

    Energy Technology Data Exchange (ETDEWEB)

    Pyatnitsa, V.A.; Bulyga, N.I.

    1988-11-01

    Discusses repair of coke oven walls and the heating system of a battery with coke ovens 7.0 m high in the Avdeevka plant. The following problems are evaluated: types of wall deformation and wear, distribution of wear zones, zones with maximum wear, coke oven repair without cooling and with cooling, repair of cracks in oven walls, effects of wall temperature (in schemes without cooling) on repair, behavior of walls in zones of temperature differences, sequence of repair operations, repair of heating channels, specific problems of wall repair at the machine side and at the pusher side of a coke oven battery, methods for reducing repair time, materials used for coke oven repair.

  19. Characterization of tuyere-level core-drill coke samples from blast furnace operation

    Energy Technology Data Exchange (ETDEWEB)

    S. Dong; N. Paterson; S.G. Kazarian; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

    2007-12-15

    A suite of tuyere-level coke samples have been withdrawn from a working blast furnace during coal injection, using the core-drilling technique. The samples have been characterized by size exclusion chromatography (SEC), Fourier transform Raman spectroscopy (FT-RS), and X-ray powder diffraction (XRD) spectroscopy. The 1-methyl-2-pyrrolidinone (NMP) extracts of the cokes sampled from the 'bosh', the rear of the 'bird's nest', and the 'dead man' zones were found by SEC to contain heavy soot-like materials (ca. 10{sup 7}-10{sup 8} apparent mass units). In contrast, NMP extracts of cokes taken from the raceway and the front of the 'bird's nest' only contained a small amount of material of relatively lower apparent molecular mass (up to ca. 10{sup 5} u). Since the feed coke contained no materials extractable by the present method, the soot-like materials are thought to have formed during the reactions of volatile matter released from the injectant coal, probably via dehydrogenation and repolymerization of the tars. The Raman spectra of the NMP-extracted core-drilled coke samples showed variations reflecting their temperature histories. Area ratios of D-band to G-band decreased as the exposure temperature increased, while intensity ratios of D to G band and those of 2D to G bands increased with temperature. The graphitic (G), defect (D), and random (R) fractions of the carbon structure of the cokes were also derived from the Raman spectra. The R fractions decreased with increasing temperature, whereas G fractions increased, while the D fractions showed a more complex variation with temperature. These data appear to give clues regarding the graphitization mechanism of tuyere-level cokes in the blast furnace. 41 refs., 9 figs., 6 tabs.

  20. Estimation of unit risk for coke oven emissions

    International Nuclear Information System (INIS)

    Moolgavkar, S.H.; Luebeck, E.G.; Anderson, E.L.

    1998-01-01

    In 1984, based on epidemiological data on cohorts of coke oven workers, USEPA estimated a unit risk for lung cancer associated with continuous exposure from birth to 1 microg/m 3 of coke oven emissions, of 6.2 x 10 -4 . This risk assessment was based on information on the cohorts available through 1966. Follow-up of these cohorts has now been extended to 1982 and, moreover, individual job histories, which were not available in 1984, have been constructed. In this study, lung cancer mortality in these cohorts of coke oven workers with extended follow-up was analyzed using standard techniques of survival analysis and a new approach based on the two stage clonal expansion model of carcinogenesis. The latter approach allows the explicit consideration of detailed patterns of exposure of each individual in the cohort. The analyses used the extended follow-up data through 1982 and the detailed job histories now available. Based on these analyses, the best estimate of unit risk is 1.5 x 10 -4 with 95% confidence interval = 1.2 x 10 -4 --1.8 x 10 -4

  1. Complete physico-chemical treatment for coke plant effluents.

    Science.gov (United States)

    Ghose, M K

    2002-03-01

    Naturally found coal is converted to coke which is suitable for metallurgical industries. Large quantities of liquid effluents produced contain a large amount of suspended solids, high COD, BOD, phenols, ammonia and other toxic substances which are causing serious pollution problem in the receiving water to which they are discharged. There are a large number of coke plants in the vicinity of Jharia Coal Field (JCF). Characteristics of the effluents have been evaluated. The present effluent treatment systems were found to be inadequate. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. Ammonia removal by synthetic zeolite, activated carbon for the removal of bacteria, viruses, refractory organics, etc. were utilized and the results are discussed. A scheme has been proposed for the complete physico-chemical treatment, which can be suitably adopted for the recycling, reuse and safe disposal of the treated effluent. Various unit process and unit operations involved in the treatment system have been discussed. The process may be useful on industrial scale at various sites.

  2. Morphological classification of coke formed from the Castilla and Jazmin crude oils

    International Nuclear Information System (INIS)

    Picon Hernandez, Hector Julio; Centeno Hurtado, Aristobulo; Pantoja Agreda, Edgar Francisco

    2008-01-01

    A morphological classification of cokes from the Castilla and Jazmin Colombian crude oils was completed. These heavy-nature crude oils, after being fractioned during the refining stages, were physicochemical characterized and submitted to the coking process. The conclusions of this work are based on the characterization of the feedstock chemical composition according to the type of aromatic carbon. UV visible spectrophotometry and the corresponding micrographs obtained by a Scan Electron Microscope (SEM), in amplification intervals from 100X to 5000X for the samples of formed cokes, were analyzed. Results of this work allowed the determination of the morphological classification intervals in function of the polyaromatic compound concentration ratio (tetraromatic/triaromatic, and diaromatic/triaromatic) of the different coked feedstock. Furthermore, high content of calcium and sulfur in the feedstock promotes morphologies of the associated - shot type

  3. PROBLEMS WITH DETERMINATION OF FUGITIVE EMISSION OF POLYCYCLIC AROMATIC HYDROCARBONS FROM COKE OVEN BATTERY

    Directory of Open Access Journals (Sweden)

    Rafał Bigda

    2017-03-01

    Full Text Available Coke oven battery is complex and multifaceted facility in terms of air pollutant emissions. As far as stack or quenching tower does not cause major difficulties of emission measurement, the fugitive emission measurement from sources such as battery top elements (charging holes, ascension pipes or oven doors is still complicated and not fully solved problem. This article presents the discussion concerning main problems and errors likely to be made in particular stages of procedure of fugitive emissions characterization from coke oven battery (selection of sampling points, sampling itself, measurement of air velocity over battery top and laboratory analyses. In addition, results of concentrations measurements of selected substances characteristic for the coking process (naphthalene, anthracene, 4 PAHs and TSP originating from fugitive sources of coke oven battery and subjected to reporting under the E-PRTR are presented. The measurements were carried out on coke oven battery top in points selected on the basis of the preceding detailed air convection velocity measurements over battery top. Results of the velocity measurements were compared with results of numerical modelling using CFD software. The presented material is an attempt to cross-sectional presentation of issues related to the quantitative evaluation of fugitive emission from coke oven battery, discussed on the example of PAHs emission as a group of substances characteristic for coking of coal.

  4. Practical aspects of coking in Cundinamarca y Boyacá

    Directory of Open Access Journals (Sweden)

    Segundo Manuel Romero-Balaguera

    2014-12-01

    Full Text Available Taking advantage of the excellent qualities of the studied coals from the coalfields in Cundinamarca and terms of the types of coking ovens, for excellent performance and quality that allows them to be very competitive.The international market is very demanding in terms of the quality of coke and CRI and CSR indexes, that is why coals laboratories were implemented and improved the system of sampling and analysis of laboratories for more agile and modern. Mixtures were made with the test methodology and empirical methods combining swelling index and rank cals were the theree main types: high, medium and low volatile. But with studies and techological change and enviromental control, process is managed, allowing the coke industry to serve as a development center for the promotion of industries in the central area of this country. In the study the whole process is presented beginning with the explotaitation of coking coals, the care that must be taken into account to mainttain good quality, transport and enviromental measures, the process of crushing and grinding to prepare the optimal mix and laboratory tests necessary to maintain quality control, the types of ovens in Boyacá Colombia, yields and advances in the se technologies, and finally, the system shutdown process. All of the above was addressed in order to add value to the product with the fulfillment of the international market standards.

  5. 46 CFR 148.04-17 - Petroleum coke, calcined, at 130 °F or above.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, calcined, at 130 °F or above. 148.04-17...-17 Petroleum coke, calcined, at 130 °F or above. (a) The requirements of this part do not apply to bulk shipments of petroleum coke, calcined, on any vessel when the material is less than 130 °F. (b...

  6. System for reducing emissions during coke oven charging; System zur Emissionsverringerung beim Fuellen von Koksoefen

    Energy Technology Data Exchange (ETDEWEB)

    Schuecker, Franz-Josef [ThyssenKrupp Industrial Solutions AG, Dortmund (Germany). Head of Oven Machine Dept., Coke Plant Technologies

    2014-10-01

    This article describes a process which reduces emissions from coke production in coke plants. The focus is on the charging process, which can be partly responsible for the fact that statutory emissions limits, which were originally met, are exceeded as coke plants get older. This article presents a solution in the form of a newly developed system that allows the oven charging system - the charging car - to respond to age-related changes in the geometry of a coke oven and thereby reduce the level of emissions.

  7. Combined effects of petrographic and technological parameters on strength of porous coke substance

    Energy Technology Data Exchange (ETDEWEB)

    Dinel' t, V.M.; Shkoller, M.B.; Stankevich, A.S.; Korchuganova, G.S.

    1983-01-01

    A laboratory study was undertaken to study the combined effects of the basic petrographic characteristics of Kuzbas coal blends and the technological carbonization parameters on the structural strength of the porous coke. Strength tests were carried out on the original coke and the products of partial gasification with carbon dioxide under conditions simulating those inside blast furnaces. Properties of the 14 samples of Kuzbas coals and composition of the four coal blends made from them are listed. It was concluded that the structural strength of coke was most strongly influenced by the average reflectance index and bulk density of the charge. Also, charge compaction can largely offset the adverse influence of petrographic heterogeneity on the strength of the coke. 10 references, 3 tables.

  8. Optimization of the coke-oven activated sludge plants

    Energy Technology Data Exchange (ETDEWEB)

    Raizer Neto, Ernesto [Santa Catarina Univ., Florianopolis, SC (Brazil); Colin, Francois [Institut de Recherches Hydrologiques, 54 - Nancy (France); Prost, Christian [Laboratoire de Sciences de Genie Chimique, Nancy (France)

    1994-12-31

    In the coke-oven activated sludge plants one of the greatest problems of malfunction is due to inffluent variability. The composition and, or, concentration variations of the inffluent substrate, which can cause an unstable system, are function of the pollutant load. Nevertheless, the knowledge of the kinetic biodegradation of the coke-oven effluent represents the limiting factor to develop an effective biological treatment. This work describes a computational model of the biological treatment which was elaborated and validated from continuous pilot scale experiments and calibrated by comparing its predictions to the pilot experiment`s results. 12 refs., 9 figs., 3 tabs.

  9. Optimization of the coke-oven activated sludge plants

    Energy Technology Data Exchange (ETDEWEB)

    Raizer Neto, Ernesto [Santa Catarina Univ., Florianopolis, SC (Brazil); Colin, Francois [Institut de Recherches Hydrologiques, 54 - Nancy (France); Prost, Christian [Laboratoire de Sciences de Genie Chimique, Nancy (France)

    1993-12-31

    In the coke-oven activated sludge plants one of the greatest problems of malfunction is due to inffluent variability. The composition and, or, concentration variations of the inffluent substrate, which can cause an unstable system, are function of the pollutant load. Nevertheless, the knowledge of the kinetic biodegradation of the coke-oven effluent represents the limiting factor to develop an effective biological treatment. This work describes a computational model of the biological treatment which was elaborated and validated from continuous pilot scale experiments and calibrated by comparing its predictions to the pilot experiment`s results. 12 refs., 9 figs., 3 tabs.

  10. A study of the performance of a reclamation soil cover placed over an oilsands coke deposit

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, D.S.; Barbour, S.L. [Saskatchewan Univ., Saskatoon, SK (Canada). Dept. of Civil Engineering; Qualizza, C. [Syncrude Canada Ltd., Fort McMurray, AB (Canada)

    2006-07-01

    Coke is a solid, carbonaceous residue that forms during the cracking of high-boiling point distillates and is one of the by-products of petroleum extraction from oilsands. Coke is known as a possible future energy source and therefore, must be stored within the reclaimed landscape in a form that allows it to be recovered. In addition, it also could be used as a low-density capping material over soft tailings. This paper presented the results of a study that examined the effects of coke in the environment. The study involved construction of two small instrumented watersheds at Syncrude Canada's Mildred Lake Settling Basin. Preliminary field data, highlighting the moisture dynamics within the covers and the underlying coke were discussed. Sand tailings underlie the hydraulically placed coke deposit. Overlying the coke were two different reclamation soil covers constructed of a peat/mineral mix over glacial or glacial lacustrine soils. Placing the finer textured soil cover over coarser grained coke produced a textural or capillary break which enhanced moisture storage for plant use while minimizing deep percolation of infiltrating water. The site has been instrumented with a meteorological station; automated soil stations to monitor suction, water content and temperature through the cover profile; lysimeters to collect net percolation; access tubes for water content monitoring; gas sampling points at depth in the coke; and standpipe piezometers to monitor water chemistry and total head in the coke at depth. 10 refs., 2 tabs., 16 figs.

  11. Hygiene of work in main shops of modern coking by-product industry. [USSR

    Energy Technology Data Exchange (ETDEWEB)

    Kapitul' skii, V B

    1984-07-01

    The hygiene of working conditions is evaluated and compared for coking by-product industry shops using modern technology and machines with those using obsolete equipment and methods. Most basic factors in contamination of atmosphere of coking, pitch-coking and metal-refining shops are coal and coke dust, carbon monoxide and polycyclic aromatic hydrocarbons, especially carcinogenic benzpyrene. Contamination of air of working zone is determined by details of technology: periodicity or continuity of industrial processes, use of improved equipment for smokeless injection of charge into stoves and of hermetic pipes to remove gas with hydraulically operated caps, position of machines in shops and in coal tar distillation removal of carcinogenic benzpyrene by sulfonation and aeration. In modernized shops of coking by-product industry, illness and loss of work capacity are significantly lower than in plants using obsolete methods and equipment. Measures are presented for hygienic improvement of working conditions; both methods to further increase efficiency of technological processes and methods to protect individual worker on job such as use of respirators, protective clothing, plexiglass shields, shampoos and skin creams. 14 references.

  12. Modelling and Simulation of Coking in the Riser of an Industrial ...

    African Journals Online (AJOL)

    Modelling and Simulation of Coking in the Riser of an Industrial Fluid Catalytic Cracking (FCC) Unit. ... Log in or Register to get access to full text downloads. ... The yields of LCO, gasoline, gas and coke that were predicted by the model for industrial risers were ... Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT

  13. Nickel and vanadium extraction from the Syrian petroleum coke

    International Nuclear Information System (INIS)

    Shlewit, H.; Alibrahim, M.

    2007-01-01

    Syrian petroleum coke samples were characterized and submitted for salt-roasting treatment in electric furnace to evaluate the convenience of this procedure for the extraction of the vanadium, nickel and sulfur from coke. Both solution and solid residue remaining after salt roasting were separated by filtration and were analyzed for vanadium, nickel and sulfur. The solution was analyzed by UV-Visible spectroscopy for vanadium and nickel and gravimetrically for sulfur. The solid residue and the untreated samples of petroleum coke were analyzed by XRF spectrometry. Results showed that more than 90% of sulfur and 60% of vanadium could be extracted by salt roasting treatment. An alternative procedure has been suggested, in which, more than 80% of sulfur and small percentage of vanadium can be leached by 0.75 M of Na 2 CO 3 solution at 70-80 Co. Vanadium was selectively extracted by DEHPA/TBP from the loaded leached solution. The extraction procedure flowsheet was also suggested. (authors)

  14. Removal of cyanide compounds from coking wastewater by ferrous sulfate: Improvement of biodegradability.

    Science.gov (United States)

    Yu, Xubiao; Xu, Ronghua; Wei, Chaohai; Wu, Haizhen

    2016-01-25

    The effect of ferrous sulfate (FeSO4) treatment on the removal of cyanide compounds and the improvement of biodegradability of coking wastewater were investigated by varying Fe:TCN molar ratios. Results suggested that the reaction between FeSO4 and coking wastewater was a two-step process. At the first step, i.e., 0≤Fe:TCN≤1.0, the reaction mechanisms were dominated by the precipitation of FeS, the complexation of CN(-), and the coagulation of organic compounds. The COD of coking wastewater decreased from 3748.1 mg/L to 3450.2 mg/L, but BOD5:COD (B/C) was improved from 0.30 to 0.51. At the second step, i.e., 1.0cyanide compounds by ferrous ions was the dominating mechanism. The COD showed a continuous increase to 3542.2 mg/L (Fe:TCN=3.2) due to the accumulated ferrous ions in coking wastewater. Moreover, B/C decreased progressively to 0.35, which was attributed to the negative effects of excess ferrous ions on biodegradability. To improve coking wastewater's biodegradability, a minimum ferrous dosage is required to complete the first step reaction. However, the optimum ferrous dosage should be determined to control a safe residual TCN in coking wastewater for the further biological treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

  15. Effect of oxide film of heat resistant alloy on coke formation during naphtha pyrolysis

    International Nuclear Information System (INIS)

    Shiratori, Nobuo; Hosoya, Keizo

    2002-01-01

    The coking of cracking furnace tubes has been an important subject of ethylene plants. The coke formations rate on the heat resistant alloys of 20Cr-4.5Al-0.5Y 2 O 3 covered with Al 2 O 3 oxide film and 25Cr-35Ni covered with Cr 2 O 3 oxide film during the thermal cracking of naphtha was quantitatively evaluated at temperatures ranging from 810 to 930 .deg. C. The experimental results showed that the coke formation rate on 20Cr-4.5Al-0.5Y 2 O 3 was lower than that on 25Cr-35Ni because of the difference of a catalytic activity to coke formation, especially in the case of a pre-carburized condition. Namely, the Al 2 O 3 formed on 20Cr-4.5Al-0.5Y 2 O 3 was stable even after carburization treatment and inert for catalytic coke formation, while coke formation on 25Cr-35Ni was under the control of catalytic coke formation, and carburization of 25Cr-35Ni accelerated catalytic coke formation. The stability of Al 2 O 3 and Cr 2 O 3 in a hydrocarbon with steam environment was thermodynamically calculated in 0.1mol of steam, 0.2mol of ethylene and 0.1mol of methane at 1,100 .deg. C. The simulation result shows that Al 2 O 3 is exceedingly stable while Cr 2 O 3 could be decomposed partially into chromium carbide. Therefore, it is concluded that Al 2 O 3 on 20Cr-4.5Al-0.5Y 2 O 3 is more stable than Cr 2 O 3 on 25Cr-35Ni, and 20Cr-4.5Al-0.5Y 2 O 3 is more resistant to coke formation and carburization than 25Cr-35Ni in a hydrocarbon with steam environment at high temperature

  16. The year-book of the Coke Oven Managers' Association 2008

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-01

    The 89th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2008 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and Committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2006-7 and of the annual general meeting 2007 are included. The Presidential address by A. Moore is about his experiences at Redcar Coke Ovens. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Six transactions are abstracted separately on the Coal Abstracts database.

  17. Crack coke in layer heat transfer analysis; Kiretsu no shinten wo tomonau kokusu sonai dennetsu kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Aoki, Hideyuki [Tohoku University, Miyagi (Japan)

    1999-03-05

    The research method heat transfer process by physical change of the coke by heat transfer from furnace wall in the retorting of coal seam filled in coke oven and flow of the gas is very complicated chamber oven style, and it does not become clear. For the purpose of the elucidation of in layer crack generation and progress mechanism, he is (1) The expansion of the softening cohesive layer. (2) Programming rate dependence of the heat. Mechanical property value on coal seam and semi- coke layer in the retorting. (3) The creep property of softening cohesive layer and semi- coke layer. (4) The setting of crack growth condition of stress intensity factor in crack tip and fracture property value of the coke by the comparison. (5) By considering the radiative heat transfer in the crack, coke in layer thermal stress analysis was carried out. The validity of these analytical result it was confirmed by the comparison with the experimental result of crack growth. Deformation behavior in the small dry distillation furnace, and crack growth mechanism in the coke layer became clear, and the prediction of the stress as micro-crack cause of generation of heating surface side coke surface and inside became possible. The numerical analysis method of the above crack growth mechanism greatly contributes to the prediction of dry distillation heating requirement and grain size of coke lump which is an index to the coke quality. Heat on material process which is accompanied by the solidification. Contraction from the softening and material migration phenomenon have been clarified by the creative research method, while this research is directly useful for energy saving of pig ironmaking process of becoming one of the ringleaders of the CO{sub 2} generation. (translated by NEDO)

  18. Volatiles production from the coking of coal; Sekitan no netsubunkai ni okeru kihatsubun seisei

    Energy Technology Data Exchange (ETDEWEB)

    Yamashita, Y.; Saito, H.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

    1996-10-28

    In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and volatiles were produced continuously at a temperature raising rate of 50{degree}C per minute, and at 3{degree}C per minute, the production of the coke and volatiles progressed stepwise as the temperature has risen. 7 refs., 6 figs.

  19. The year-book of the Coke Oven Managers' Association 2006

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The 87th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2006 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and Committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2004-5 and of the annual general meeting 2005 are included. The Presidential address by M. Gore is on the last five years of Monckton Coke and Chemical Company. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Seven transactions are abstracted separately on the Coal Abstracts database.

  20. Priorities in the design of chemical shops at coke plants

    Energy Technology Data Exchange (ETDEWEB)

    V.I. Rudyka; Y.E. Zingerman; V.V. Grabko; L.A. Kazak [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Recent trends in the design of chemical equipment at coke plants are described, through the lens of experience at Giprokoks. The main priorities were to improve the removal of impurities from coke oven gas; to improve equipment design on the basis of new materials; to reduce reagent consumption; to reduce the materials and energy consumed in the construction of new equipment; and to minimize impacts on the environment and worker health. Some technological equipment is briefly characterized.

  1. Microporous Cokes Formed in Zeolite Catalysts Enable Efficient Solar Evaporation

    KAUST Repository

    Wang, Jianjian

    2017-03-13

    Cokes are inevitably generated during zeolite-catalyzed reactions as deleterious side products that deactivate the catalyst. In this study, we in-situ converted cokes into carbons within the confined microporous zeolite structures and evaluated their performances as absorbing materials for solar-driven water evaporation. With a properly chosen zeolite, the cokederived carbons possessed ordered interconnected pores and tunable compositions. We found that the porous structure and the oxygen content in as-prepared carbons had important influences on their energy conversion efficiencies. Among various investigated carbon materials, the carbon derived from the methanol-to-olefins reaction over zeolite Beta gave the highest conversion efficiency of 72% under simulated sunlight with equivalent solar intensity of 2 suns. This study not only demonstrates the great potential of traditionally useless cokes for solar thermal applications but also provides new insights into the design of carbon-based absorbing materials for efficient solar evaporation.

  2. NO{sub x} reduction by coke deposited on Pt/Al{sub 2}O{sub 3} in an oxidizing medium; Elimination des NO{sub x} par le coke depose sur Pt/Al{sub 2}O{sub 3} en milieu oxydant

    Energy Technology Data Exchange (ETDEWEB)

    Lunati, S

    1997-12-12

    NO{sub x} reduction by coke deposited on Pt/Al{sub 2}O{sub 3} was studied in excess oxygen. Continuous analysis of the effluent was performed with a mass spectrometer. The coking reaction was carried out under reducing conditions with two different coking agents: cyclopentane and heptanal. In general, NO{sub x} reduction by coke deposited on Pt/Al{sub 2}O{sub 3} occurs in a wide temperature range (200 deg Ccoke reducing ability and the temperature window depend closely on the chemical nature of the carbon deposits. Thereby, a coke made from heptanal which contains oxygenated functions (carbonyl and hydroxyl groups) within the carbon structure, is more selective and reduce NO{sub x} at lower temperature than a coke made from cyclopentane which does not contain these functional groups. Based on our results, we proposed a `dual-site` reaction for NO{sub x} reduction on coked Pt/Al{sub 2}O{sub 3} catalyst. Platinum allows O{sub 2} activation by dissociative adsorption, and NO{sub 2} formation by oxidation of NO. NO{sub x} reduction occurs on carbon deposits. Reaction between NO{sub x} and coke leads to the formation of N-containing species which are decomposed in CI{sub 2}, H{sub 2}O, N{sub 2} and N{sub 2}O by reaction with activated O{sub 2}. (author) 205 refs.

  3. Integrated process for synthetic natural gas production from coal and coke-oven gas with high energy efficiency and low emission

    International Nuclear Information System (INIS)

    Man, Yi; Yang, Siyu; Qian, Yu

    2016-01-01

    Highlights: • A novel coal and coke-oven gas to SNG (CGtSNG) process is proposed. • Energy efficiency of CGtSNG increases 8% compared to coal-to-SNG process. • CGtSNG reduces 60% CO_2 emission and 72% effluent discharge. • CGtSNG proposes an idea of using redundant coke-oven gas for producing SNG production. - Abstract: There was a rapid development of coal to synthetic natural gas (SNG) projects in the last few years in China. The research from our previous work and some other researchers have found coal based SNG production process has the problems of environmental pollution and emission transfer, including CO_2 emission, effluent discharge, and high energy consumption. This paper proposes a novel co-feed process of coal and coke-oven gas to SNG process by using a dry methane reforming unit to reduce CO_2 emissions, more hydrogen elements are introduced to improve resource efficiency. It is shown that the energy efficiency of the co-feed process increases by 4%, CO_2 emission and effluent discharge is reduced by 60% and 72%, whereas the production cost decreases by 16.7%, in comparison to the conventional coal to SNG process. As coke-oven gas is a waste gas in most of the coking plant, this process also allows to optimize the allocation of resources.

  4. Development and Testing of the Advanced CHP System Utilizing the Off-Gas from the Innovative Green Coke Calcining Process in Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Chudnovsky, Yaroslav [Gas Technology Inst., Des Plaines, IL (United States); Kozlov, Aleksandr [Gas Technology Inst., Des Plaines, IL (United States)

    2013-08-15

    Green petroleum coke (GPC) is an oil refining byproduct that can be used directly as a solid fuel or as a feedstock for the production of calcined petroleum coke. GPC contains a high amount of volatiles and sulfur. During the calcination process, the GPC is heated to remove the volatiles and sulfur to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages. However, coke calcination in an electrothermal fluidized bed (EFB) opens up a number of potential benefits for the production enhancement, while reducing the capital and operating costs. The increased usage of heavy crude oil in recent years has resulted in higher sulfur content in green coke produced by oil refinery process, which requires a significant increase in the calcinations temperature and in residence time. The calorific value of the process off-gas is quite substantial and can be effectively utilized as an “opportunity fuel” for combined heat and power (CHP) production to complement the energy demand. Heat recovered from the product cooling can also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. As such, the efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world. The developed technology is intended to accomplish the following objectives: - Reduce the energy and carbon intensity of the calcined coke production process. - Increase utilization of opportunity fuels such as industrial waste off-gas from the novel

  5. Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Bayraktur, K.N.; Lawson, G.J.

    1984-09-01

    Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lowerrank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy.

  6. Properties and potential of formed cokes derived from two Turkish lignites by carbonization of binderless briquettes

    Energy Technology Data Exchange (ETDEWEB)

    Bayraktar, K.N.; Lawson, G.J.

    1984-09-01

    Two high-sulphur Turkish lignites were briquetted at room temperature under pressures of 113 or 212 MPa and the briquettes were carbonized to 1158-1173 K over special heating cycles. The lower-rank lignite gave a formed coke of superior mechanical strength, lower porosity and higher sulphur content than typical blast furnace cokes. The formed coke produced from the higher-rank lignite briquettes had slightly poorer mechanical strength, lower porosity and much higher ash yield and sulphur content than conventional cokes. The products were considered attractive for use in non-ferrous metallurgy. 38 references.

  7. Post oxygen treatment characteristics of coke as an anode material for Li-ion batteries.

    Science.gov (United States)

    Kim, Jae-Hun; Park, Min-Sik; Jo, Yong Nam; Yu, Ji-Sang; Jeong, Goojin; Kim, Young-Jun

    2013-05-01

    The effect of a oxygen treatment on the electrochemical characteristics of a soft carbon anode material for Li-ion batteries was investigated. After a coke carbonization process at 1000 degrees C in an argon atmosphere, the samples were treated under a flow of oxygen gas to obtain a mild oxidation effect. After this oxygen treatment, the coke samples exhibited an improved initial coulombic efficiency and cycle performance as compared to the carbonized sample. High-resolution transmission electron microscopy revealed that the carbonized cokes consisted of disordered and nanosized graphene layers and the surface of the modified carbon was significantly changed after the treatment. The chemical state of the cokes was analyzed using X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The enhanced electrochemical properties of the surface modified cokes could be attributed to the mild oxidation effect induced by the oxygen treatment. The mild oxidation process could have led to the elimination of surface imperfections and the reinforcement of a solid electrolyte interphase film, which resulted in the improved electrochemical characteristics.

  8. Influence of Coke Ratio on the Sintering Behavior of High-Chromium Vanadium-Titanium Magnetite

    Directory of Open Access Journals (Sweden)

    Songtao Yang

    2017-06-01

    Full Text Available High-chromium vanadium and titanium magnetite (HCVTM sinter has poor properties. The coke ratio has an important effect on the behavior of HCVTM sintering as it affects the mineral phases in the high-chromium vanadium and titanium sinter (HCVTS via changing the sintering temperature and atmosphere. In this work, the sintering behavior of HCVTM mixed with varying coke ratios was investigated through sintering pot tests, X-ray diffraction (XRD, gas chromatographic analysis, and mineral phase analysis. The results show that, with the increase of the coke ratio from 4.0% to 6.0%, leading to the increase of the combustion ratio of the flue gas, the vertical sintering rate and sinter productivity decrease. Meanwhile, with the change of the coke ratio, the content of magnetite, silicate, and perovskite increase, while the hematite and calcium ferrite decrease. In addition, the tumble strength and reduction ability of HCVTS decrease, and its degradation strength increase. It was found that the appropriate coke ratio for the sintering process was 5.0 wt %.

  9. The year-book of the Coke Oven Managers' Association 2007

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-07-01

    The 88th volume of the Year Book outlines activities of the Coke Oven Managers' Association throughout 2007 and reproduces transactions presented to the industry through its various sections. It includes lists of Council and committee members and representation on committees and past presidents, and a full list of members. Reports of Council 2005-6 and of the annual general meeting 2005 are included. The Presidential address by R.G.W. Sargent looks at the situation faced by coke oven managers through the decades with some predictions for the future. Carbonisation and briquetting works in the United Kingdom, Koppers carbon materials and chemical works in the UK and Europe, European coking plants, their addresses and managers are listed. Nine transactions are abstracted separately on the Coal Abstracts database.

  10. A XANES Study of Sulfur Speciation and Reactivity in Cokes for Anodes Used in Aluminum Production

    Science.gov (United States)

    Jahrsengene, Gøril; Wells, Hannah C.; Rørvik, Stein; Ratvik, Arne Petter; Haverkamp, Richard G.; Svensson, Ann Mari

    2018-06-01

    Availability of anode raw materials in the growing aluminum industry results in a wider range of petroleum cokes being used to produce carbon anodes. The boundary between anode grade cokes and what previously was considered non-anode grades are no longer as distinct as before, leading to introduction of cokes with higher sulfur and higher trace metal impurity content in anode manufacturing. In this work, the chemical nature of sulfur in five industrial cokes, ranging from 1.42 to 5.54 wt pct S, was investigated with K-edge XANES, while the reactivity of the cokes towards CO2 was measured by a standard mass loss test. XANES identified most of the sulfur as organic sulfur compounds. In addition, a significant amount is identified (16 to 53 pct) as S-S bound sulfur. A strong inverse correlation is observed between CO2-reactivity and S-S bound sulfur in the cokes, indicating that the reduction in reactivity is more dependent on the amount of this type of sulfur compound rather than the total amount of sulfur or the amount of organic sulfur.

  11. New and revised standards for coke production

    Energy Technology Data Exchange (ETDEWEB)

    G.A. Kotsyuba; M.I. Alpatov; Y.G. Shapoval [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    The need for new and revised standards for coke production in Ukraine and Russia is outlined. Such standards should address improvements in plant operation, working conditions, environmental protection, energy conservation, fire and explosion safety, and economic indices.

  12. Effect of volume change of coal during plastic and resolidifying phase on the internal gas pressure in coke ovens; Sekitan nanka saikoka katei ni okeru taiseki henka ga cokes ro no nanka yoyu sonai gas atsu ni oyobosu eikyo

    Energy Technology Data Exchange (ETDEWEB)

    Nomura, S; Arima, T [Nippon Steel Corp., Tokyo (Japan)

    2000-08-01

    The coking pressure in coke oven, which is caused by the internal gas pressure in the coal plastic layer, is determined by the gas permeability of the layer. The gas permeability of the plastic layer depends on its density as well as the physical property of the plastic coal itself The plastic layer is between the coke layer and the coal layer and the effect of the volume change of these outer layers, i.e. contraction and compression, on the density and the internal gas pressure of the plastic layer was studied. Sandwich carbonization test, where different coals were charged in the test coke oven, showed that the internal gas pressure in the plastic layer depends not only on the one kind of coal in plastic phase but also on the other kind of coal in resolidifying phase near the oven walls. The relative volume of coke transformed from the unit volume of coal was measured using X-ray CT scanner and it varied greatly across the coke oven width depending on the kinds of coals. The volume change of coal during plastic and resolidifying phase affects the density and the internal gas pressure of the plastic layer The relative volume of semicoke and coke transformed from the unit volume of coal near the oven walls is higher for a high coking pressure coal than that for a low coking pressure coal. This leads to the high density of the plastic layer and the generation of dangerously high internal gas pressure in the oven centre. (author)

  13. Factors affecting coke size and fissuring during cokemaking part 2

    Energy Technology Data Exchange (ETDEWEB)

    Merrick Mahoney; Jeff Keating; Susan Woodhouse [BHP Billiton Newcastle Technology Centre (Australia)

    2007-12-15

    This work addressed the mechanism of fissuring during metallurgical cokemaking and extends on a previous ACARP project. Considerable progress has been made in understanding the mechanism by an integrated modelling work; experimental program. The work points to opportunities for controlling the carbonisation process to achieve required outcomes in terms of coke lump size and distribution. Key outcomes of the work included: A methodology for determination of the minimum spacing between fissures, and the time at which period doublings (i.e. every second fissure stopping) occur, has been developed and implemented. Implementation of the methodology allows the determination of the complete fissure pattern (at least those perpendicular to the oven walls) for a given coke oven/charge configuration. A plausible mechanistic explanation of the formation of lateral fissures (those that are parallel to the oven walls) has been developed. Knowledge of the fissure pattern, combined with the lateral fissuring explanation, enables the determination of typical size and shape of lumps after stabilisation of the coke.

  14. A temperature measurement system for coke-oven walls at the coke-oven plant Kaiserstuhl in Dortmund (Germany). Pomiar temperatury w scianach baterii koksowniczej w koksownii Kaisertuhl w Dortmund (Niemcy)

    Energy Technology Data Exchange (ETDEWEB)

    Chojnacki, M.; Sitek, A. (Hanslik Laboratorium Oprgramowania, Katowice (Poland))

    1994-08-01

    In the article, the software and hardware solutions developed by Hanslik Software Laboratory for Ruhrkohle AG are presented. The system was installed at Kaiserstuhl in Dortmund (Germany), the most modern coke-oven plant in the world. The project covered a temperature measurement system for the coke-oven walls as well as monitoring of the protection sensors in real-time. The article describes also the testing methodology we adopted, using computer aided testing. For the testing purposes, a simulator of the coke-oven and a testing program running under Windows were developed at our laboratory. The article shows the advantages of using off the shelf programmable components for ruggedized industrial applications. (author). 4 refs.

  15. Water protection in coke-plant design

    Energy Technology Data Exchange (ETDEWEB)

    G.I. Alekseev [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Wastewater generation, water consumption, and water management at coke plants are considered. Measures to create runoff-free water-supply and sewer systems are discussed. Filters for water purification, corrosion inhibitors, and biocides are described. An integrated single-phase technology for the removal of phenols, thiocyanides, and ammoniacal nitrogen is outlined.

  16. South Bank Coke Ovens heating performance improvements

    Energy Technology Data Exchange (ETDEWEB)

    Fraser, A.J. [South Bank Coke Ovens (United Kingdom)

    1995-12-31

    The coke oven batteries at South Bank Coke Ovens had a history of refractory failure, overheating, and poor environmental performance despite repeated attempts to solve the problem. The fundamental design was poor, but previous upgrade attempts had a history of short term improvements followed by renewed decline, suggesting that the problem may not merely with the equipment. An audit of the area showed multiple morale, equipment and communications problems, although a significant proportion of the workforce were interested in improving the situation. A group of those interested in performance improvements was called together and objectives agreed upon. Communications were upgraded and problem walls analysed for their particular weaknesses. A team approach was used for maintenance, leading to slowly improving pushing emission factors. Temperature control equipment ensured better environmental performance and lower electricity consumption. 5 refs., 3 figs.

  17. 40 CFR 63.305 - Alternative standards for coke oven doors equipped with sheds.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Alternative standards for coke oven doors equipped with sheds. 63.305 Section 63.305 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries § 63.305 Alternative standards for...

  18. Electrical Resistivity Measurement of Petroleum Coke Powder by Means of Four-Probe Method

    Science.gov (United States)

    Rouget, G.; Majidi, B.; Picard, D.; Gauvin, G.; Ziegler, D.; Mashreghi, J.; Alamdari, H.

    2017-10-01

    Carbon anodes used in Hall-Héroult electrolysis cells are involved in both electrical and chemical processes of the cell. Electrical resistivity of anodes depends on electrical properties of its constituents, of which carbon coke aggregates are the most prevalent. Electrical resistivity of coke aggregates is usually characterized according to the ISO 10143 standardized test method, which consists of measuring the voltage drop in the bed of particles between two electrically conducing plungers through which the current is also applied. Estimation of the electrical resistivity of coke particles from the resistivity of particle bed is a challenging task and needs consideration of the contribution of the interparticle void fraction and the particle/particle contact resistances. In this work, the bed resistivity was normalized by subtracting the interparticle void fraction. Then, the contact size was obtained from discrete element method simulation and the contact resistance was calculated using Holm's theory. Finally, the resistivity of the coke particles was obtained from the bed resistivity.

  19. Nature of nitrogen specie in coke and their role in NOx formation during FCC catalyst regeneration

    International Nuclear Information System (INIS)

    Babich, I.V.; Seshan, K.; Lefferts, L.

    2005-01-01

    NO x emission during the regeneration of coked fluid catalytic cracking (FCC) catalysts is an environmental problem. In order to follow the route to NO x formation and try to find ways to suppress it, a coked industrial FCC catalyst has been prepared using model N-containing compounds, e.g., pyridine, pyrrole, aniline and hexadecane-pyridine mixture. Nitrogen present in the FCC feed is incorporated as polyaromatic compounds in the coke deposited on the catalyst during cracking. Its functionality has been characterized using XPS. Nitrogen specie of different types, namely, pyridine, pyrrolic or quaternary-nitrogen (Q-N) have been discriminated. Decomposition of the coke during the catalyst regeneration (temperature programmed oxidation (TPO) and isothermal oxidation) has been monitored by GC and MS measurements of the gaseous products formed. The pyrrolic- and pyridinic-type N specie, present more in the outer coke layers, are oxidized under conditions when still large amount of C or CO is available from coke to reduced NO x formed to N 2 . ''Q-N'' type species are present in the inner layer, strongly adsorbed on the acid sites on the catalyst. They are combusted last during regeneration. As most of the coke is already combusted at this point, lack of reductants (C, CO, etc.) results in the presence of NO x in the tail gas

  20. 76 FR 52350 - Coke Oven Emissions Standard; Extension of the Office of Management and Budget's (OMB) Approval...

    Science.gov (United States)

    2011-08-22

    ... Standard provide protection for workers from the adverse health effects associated with exposure to coke...' exposure to coke oven emissions, monitor worker health, and provide workers with information about their exposures and the health effects of exposure to coke oven emissions. II. Special Issues for Comment OSHA has...

  1. Urgent reconstruction and re-equipping of coking plants

    Energy Technology Data Exchange (ETDEWEB)

    Kvitkin, I.A.; Martynenko, V.M.; Rozenfel' d, M.S.; Svyatogorov, A.A.; Shvartsman, I.G.

    1986-03-01

    This paper discusses the various options involved: complete or partial reconstruction of existing buildings and equipment or new construction with new equipment and new underground and surface communications. It explains that reconstruction work is divided into three phases: initial phase (clearance, dismantling, closing down coking batteries); basic phase (fitting heat-resistant materials, prestart-up assembly work); final phase (drying out, heating up, adjustments, start-up). A structured scheme for a typical initial phase is described and a method of calculating the durations of the various phases is discussed. Conclusion is that there is an urgent requirement for a document to be produced for the control of reconstruction work; it should contain standard durations and could serve as a standard for coking plant reconstruction work.

  2. Significance and development of the utilization of brown coal high temperature coke in the economy of the GDR for the period 1964 to 1974

    Energy Technology Data Exchange (ETDEWEB)

    Klose, E.; Heschel, W.

    1979-01-01

    Brown coal high temperature coke production in GDR in the years since 1964 is described. In 1969 the second large brown coal high temperature coking plant, Schwarze Pumpe, went into operation, increasing the total brown coal high temperature coke production to 2 million tons annually. Utilization of the coke size classes in mm from 0-3.15, 3.15-20, 20-31.5, 31.5-45 and greater than 45 mm in the metallurgical, chemical, and energy industries as well as for household heating is shown with figures from 1964, 1970 and 1974. The increasing use of coke in households partly as briquet substitution is also shown (in 1970 42% of the coke was used in households). The substitution of black coal coke by brown coal coke in additional fields of industrial production was also further advanced. Coke production at the Schwarze Pumpe plant is scheduled to increase to 1.6 million tons by 1985 by means of the application of improved coking technologies. Investigations for future industrial solutions to the following coking problems are being conducted: processing coke fines (which make up 10 to 12% of the total produced coke) by briquetting with binders into formed coke, firing coke fines in blast furnaces and power plants, mixed briquetting of coke fines with limestone for carbide production and mixed briquetting of coke and ore fines for metallurgical purposes. (8 refs.) (In German)

  3. A comparative economic assessment of hydrogen production from coke oven gas, water electrolysis and steam reforming of natural gas

    International Nuclear Information System (INIS)

    Nguyen, Y.V.; Ngo, Y.A.; Tinkler, M.J.; Cowan, N.

    2003-01-01

    This paper presents the comparative economics of producing hydrogen for the hydrogen economy by recovering it from waste gases from the steel industry, by water electrolysis and by conventional steam reforming of natural gas. Steel makers produce coke for their blast furnace operation by baking coal at high temperature in a reduced environment in their coke ovens. These ovens produce a coke oven gas from the volatiles in the coal. The gas, containing up to 60% hydrogen, is commonly used for its heating value with some of it being flared. The feasibility of recovering this hydrogen from the gas will be presented. A comparison of this opportunity with that of hydrogen from water electrolysis using low cost off-peak electricity from nuclear energy will be made. The impact of higher daily average electricity rate in Ontario will be discussed. The benefits of these opportunities compared with those from conventional steam reforming of natural gas will be highlighted. (author)

  4. Effect of Extracted Compositions of Liquefaction Residue on the Structure and Properties of the Formed-coke

    Directory of Open Access Journals (Sweden)

    Song Yong-hui

    2016-01-01

    Full Text Available The purpose of this paper is to study the effect of extracted compositions of the de-ash liquefaction residue (D-DCLR on pyrolysis products yields, compressive strength and composition of the formed-coke, which was prepared by co-pyrolysis of the low metamorphic pulverized coal and D-DCLR. The scanning electron microscope (SEM and the Fourier Transform Infrared (FT-IR were used to characterize the morphology and functional group of the formed-coke, respectively. The results showed that the extracted compositions of D-DCLR were heavy oil (HS, asphaltene (A, pre-asphaltene (PA and tetrahydrofuran isolusion (THFIS, whose contents were 5.10%, 40.90%, 14.4%, 39.60%, respectively. During the pyrolysis process, HS was the main source of tar, and HS, A as well as PA were conducive to improve gas yields. The THFIS helped to improve the yield of the formed-coke up to 89.5%, corresponding to the compressive strength was only 147.7N/ball for the coke. A and PA were the key factors affecting the compressive strength and surface structure of the formed-coke. The compressive strength of coke could be up to 728.0N/ball with adding D-DCLR, which reduced by 50% after the removal of A and PA. The FT-IR analysis showed that the types of surface functional groups of the formed-coke were remained the same after co-pyrolysis, but the absorption peak intensity of each functional group was changed.

  5. Investigating erosion of building materials used in an installation for pneumatic transport of coke breeze and coal

    Energy Technology Data Exchange (ETDEWEB)

    Bandrowski, J.; Kot-Borkowska, Z.; Misztal, M.; Raczek, J.; Kaczmarzyk, G.

    1980-09-01

    This article investigates the influence of the following factors on erosion of building material used in pneumatic transport of coal and coke breeze: intensity of coal or coke breeze flow within the range of 47 to 120 kg/h for coke and 99 to 165 kg/h for coal; speed of solid material particles within the range 3.71 to 7.97 m/s for coke, and 3.30 to 7.58 m/s for coal; duration of the experiments 0.5 to 1.5 h for coke and 2.0 to 5.0 for coal; angle of inclination of the sample of building material 30 to 60 degrees for both coal and coke breeze. Three types of construction material used in pneumatic transport were tested: steel, concrete and chamotte bricks. Investigations show that concrete is characterized by the highest erosion, chamotte bricks by medium erosion and steel by the lowest erosion. As a result of mathematical processing of experimental data, empirical models of erosion of the three materials are constructed. (7 refs.)

  6. Reaction Mechanism for the Formation of Nitrogen Oxides (NO x ) During Coke Oxidation in Fluidized Catalytic Cracking Units

    KAUST Repository

    Chaparala, Sree Vidya

    2015-06-11

    Fluidized catalytic cracking (FCC) units in refineries process heavy feedstock obtained from crude oil distillation. While cracking feed, catalysts get deactivated due to coke deposition. During catalyst regeneration by burning coke in air, nitrogen oxides (NOx) are formed. The increase in nitrogen content in feed over time has resulted in increased NOx emissions. To predict NOx concentration in flue gas, a reliable model for FCC regenerators is needed that requires comprehensive understanding and accurate kinetics for NOx formation. Based on the nitrogen-containing functional groups on coke, model molecules are selected to study reactions between coke-bound nitrogen and O2 to form NO and NO2 using density functional theory. The reaction kinetics for the proposed pathways are evaluated using transition state theory. It is observed that the addition of O2 on coke is favored only when the free radical is present on the carbon atom instead of nitrogen atom. Thus, NOx formation during coke oxidation does not result from the direct attack by O2 on N atoms of coke, but from the transfer of an O atom to N from a neighboring site. The low activation energies required for NO formation indicate that it is more likely to form than NO2 during coke oxidation. The favorable pathways for NOx formation that can be used in FCC models are identified. Copyright © 2015 Taylor & Francis Group, LLC.

  7. ECONOMIC MODEL AND TOOLS OF THE AIR PROTECTION MANAGEMENT BASED ON THE EXAMPLE OF A COKING PLANT

    Directory of Open Access Journals (Sweden)

    Danuta Hilse

    2014-10-01

    Full Text Available Legal-economic models of the air protection management at the Polish industrial plants, which take into account the regulations of the Act on “Environment protection law”, are far from being perfect. It is particularly noticeable in the coking industry where chargeable pollutions are chosen selectively, and unitary rates of emission charges are agreed at random. Tax deductions are not granted either to producers of fuel coke for reduction of pollutants emission in municipal-housing management after replacing coal with fuel coke. The proposed new economic model of the air protection management at coking plants eliminates the existing shortcomings.

  8. Coke drums inspection and evaluation using stress and strain analysis techniques

    Energy Technology Data Exchange (ETDEWEB)

    Haraguchi, Marcio Issamu [Tricom Tecnologia e Servicos de Manutencao Industrial Ltda., Piquete, SP (Brazil); Samman, Mahmod [Houston Engineering Solutions, Houston, TX (United States); Tinoco, Ediberto Bastos; Marangone, Fabio de Castro; Silva, Hezio Rosa da; Barcelos, Gustavo de Carvalho [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

    2012-07-01

    Coke drums deform due to a complex combination of mechanical and thermal cyclic stresses. Bulges have progressive behavior and represent the main maintenance problem related to these drums. Bulge failure typically result in through-wall cracks, leaks, and sometimes fires. Such failures generally do not represent a great risk to personnel. Repairs needed to maintain reliability of these vessels might require extensive interruption to operation which in turn considerably impacts the profitability of the unit. Therefore the condition, progression and severity of these bulges should be closely monitored. Coke drums can be inspected during turnaround with 3D Laser Scanning and Remote Visual Inspection (RVI) tools, resulting in a detailed dimensional and visual evaluation of the internal surface. A typical project has some goals: inspect the equipment to generate maintenance or inspection recommendations, comparison with previous results and baseline data. Until recently, coke drum structural analysis has been traditionally performed analyzing Stress Concentration Factors (SCF) thought Finite Element Analysis methods; however this technique has some serious technical and practical limitations. To avoid these shortcomings, the new strain analysis technique PSI (Plastic Strain Index) was developed. This method which is based on API 579/ ASME FFS standard failure limit represents the state of the art of coke drum bulging severity assessment has an excellent correlation with failure history. (author)

  9. Physico-chemical treatment of coke plant effluents for control of water pollution in India

    Energy Technology Data Exchange (ETDEWEB)

    Ghose, M.K. [Indian School of Mines, Dhanbad (India). Center of Mining Environmental

    2002-01-01

    Coal carbonizing industries in India are important and are growing every year. Large quantities of liquid effluents produced in this industry contain a large amount of suspended solids, high biochemical oxygen demand (BOD), chemical oxygen demand (COD), phenols, ammonia and other toxic substances, which are causing serious surface water pollution in the area. There is a large number of coke plants in the vicinity of Jharia Coal Field (JCF). The working principle of a coke plant and the effluents produced is described. One large coke plant was chosen to evaluate characteristics of the effluent and to suggest a proper treatment method. Present effluent treatment system was found to be inadequate and a large quantity of a very good quality coke breeze is being lost, which is also causing siltation on the riverbed in addition to surface water pollution. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. A scheme has been proposed for the treatment, which can be suitably adopted for the recycling, reuse or safe disposal of the treated effluent. Various unit process and unit operations are discussed. The process may be useful on industrial scale for various sites so as to maintain a clean environment.

  10. Influence of thermal charge preparation on coke comminution under blast-furnace operating conditions

    Energy Technology Data Exchange (ETDEWEB)

    Shkoller, M.B.; Dinel' t, V.M.; Korchuganova, G.S.; Petrov, V.B.

    1983-01-01

    An investigation is described for the study of structural breakdown of coke by thermochemical action of alkali and alkaline-earth metal vapors under blast furnace operating conditions. Bench-scale test facilities are described in which a pair of coke samples are exposed to the metal vapors then subjected to gasification. Structural strength tests were performed before and after each experiment. Coke samples were obtained in either moist or thermally prepared condition. The value of thermal charge preparation (heat treatment of the coal at 150/sup 0/C in a fluidized bed) was established, since it shifts the pore size distribution to the smaller size, thereby retarding adsorption of the metal vapors. 16 references, 4 figures, 2 tables.

  11. Benzole still reflux system - Dawes Lane Coke Ovens

    Energy Technology Data Exchange (ETDEWEB)

    Hardwick, J.

    2005-07-01

    The paper describes a project carried out at Dawes Lane coking plant (in Scunthorpe, UK) to access current performance of the batch reflux system with respect to the operation of personnel and to recommend a solution to eliminate naphthalene blockage and problems previously caused by the use of hot debenzolised oil (DBO) as make-up. A successful solution was found and implemented. The benzole product now being produced is within specification and regularly achieves the composition produced by the previous hot reflux system (83% benzole, 7% naphthalene) with an addition reduction in wash oil usage of 20%. Problems of naphthalene blockages in reflux pipework have been cured. The expenses on the project were small. The paper was presented at a COMA meeting at Monckton Coke Ovens on 19 May 2005. 6 figs.

  12. The effect of ash elements in petroleum coke on hearth furnace heat recovery system performance

    Energy Technology Data Exchange (ETDEWEB)

    Akhmetov, M M

    1981-01-01

    Difficulties encountered in the operation of the heat recovery system of a calcination plant at Krasnovodsk Refinery caused by ash element deposits blocking the fire box are described. Deposits and coke ash composition are given. The main cause of blocking was found to be the removal of sea water salt elements which get on the coke surface when the retarded coking plant is discharged with a water-jet borer. Switching over to fresh water and air-blasting of heat recovery pipes decreased blocking considerably.

  13. Coking processes

    Energy Technology Data Exchange (ETDEWEB)

    Rollason, A

    1913-09-01

    In the production of light hydrocarbon oils from coals, cannels, or shales which are high in oxygen, from 3 to 5% of limestone or other suitable carbonate is added to the coking-charge. The carbonate added is proportionate to the oxygen contained in the coal etc. The charge is slowly heated up to a temperature of about 500/sup 0/C., water is driven off between 85 and 105/sup 0/C., and carbon dioxide is evolved at a low temperature and retards the evolution of combustible gases until a temperature between 130 and 175/sup 0/C., is reached. Upon formation of the endothermic hydrocarbons, the temperature of the charge becomes lowered, a large volume of light oils of the benzol series is produced, and an increased yield of ammonia is obtained, leaving the carbon in graphitic form.

  14. Pt/Cu single-atom alloys as coke-resistant catalysts for efficient C-H activation

    Science.gov (United States)

    Marcinkowski, Matthew D.; Darby, Matthew T.; Liu, Jilei; Wimble, Joshua M.; Lucci, Felicia R.; Lee, Sungsik; Michaelides, Angelos; Flytzani-Stephanopoulos, Maria; Stamatakis, Michail; Sykes, E. Charles H.

    2018-03-01

    The recent availability of shale gas has led to a renewed interest in C-H bond activation as the first step towards the synthesis of fuels and fine chemicals. Heterogeneous catalysts based on Ni and Pt can perform this chemistry, but deactivate easily due to coke formation. Cu-based catalysts are not practical due to high C-H activation barriers, but their weaker binding to adsorbates offers resilience to coking. Using Pt/Cu single-atom alloys (SAAs), we examine C-H activation in a number of systems including methyl groups, methane and butane using a combination of simulations, surface science and catalysis studies. We find that Pt/Cu SAAs activate C-H bonds more efficiently than Cu, are stable for days under realistic operating conditions, and avoid the problem of coking typically encountered with Pt. Pt/Cu SAAs therefore offer a new approach to coke-resistant C-H activation chemistry, with the added economic benefit that the precious metal is diluted at the atomic limit.

  15. Pt/Cu single-atom alloys as coke-resistant catalysts for efficient C–H activation

    Energy Technology Data Exchange (ETDEWEB)

    Marcinkowski, Matthew D.; Darby, Matthew T.; Liu, Jilei; Wimble, Joshua M.; Lucci, Felicia R.; Lee, Sungsik; Michaelides, Angelos; Flytzani-Stephanopoulos, Maria; Stamatakis, Michail; Sykes, E. Charles H.

    2018-01-08

    The recent availability of shale gas has led to a renewed interest in C-H bond activation as the first step towards synthesis of fuels and fine chemicals. Heterogeneous catalysts based on Ni and Pt can perform this chemistry, but deactivate easily due to coke formation. Cu- based catalysts are not practical for this chemistry due to high C-H activation barriers, but their weaker binding to adsorbates offers resilience to coking. Utilizing Pt/Cu single atom alloys (SAAs) we examine C-H activation in a number of systems including methyl groups, methane, and butane using a combination of simulations, surface science, and catalysis studies. We find that Pt/Cu SAAs activate C-H bonds more efficiently than Cu, are stable for days under realistic operating conditions, and avoid the problem of coking typically encountered with Pt. Pt/Cu SAAs therefore offer a new approach to coke resistant C-H activation chemistry with the added economic benefit that the precious metal is diluted at the atomic limit.

  16. Prediction of vertical expansion pressure stresses in coke oven heating walls

    Energy Technology Data Exchange (ETDEWEB)

    Duerselen, H; Janicka, J

    1987-08-01

    The paper describes an accurate method developed by Krupp Koppers for calculating stresses in the central areas of coke oven heating walls. The results of this calculation model have provided the following conclusions for the design of coke ovens: 1) a rising pre-stressing of the heating walls caused by the weight of the top deck of the coke oven leads - compared with the stress limits of W. Ahlers - to lower permissible expansion pressures. 2) A given heating wall width has its corresponding maximum feasible oven height. Heating wall width and top deck weight are not interchangeable parameters. 3) The dependence of the permissible expansion pressure on the stretcher brick thickness should not be overlooked. Stretcher brick thicknesses of under 90 mm are not recomended for tall ovens and heavily swelling coal. 4) The capacity of mortar to absorb tensile stresses is ultimately an undesirable property, because the stresses at the points where the mortar is not holding are higher than in a straightforward stretch of brickwork.

  17. Non-competitive market behaviour in the international coking coal market

    International Nuclear Information System (INIS)

    Graham, P.; Thorpe, S.; Hogan, L.

    1999-01-01

    In this paper, a primal dual programming model of international coking coal trade is constructed to test for non-competitive market behaviour. World trade in 1996 is simulated under perfect competition and various non-competitive market structures. Statistical tests are used to compare simulated trade flows with actual data. Assuming Cournot-Nash behaviour, an all consumer oligopsony market structure is preferred to alternative models. Under an all consumer oligopsony world coking coal prices and trade are lower than under perfect competition. Under an oligopsonistic structure welfare gains from productivity increases in Australian coal mines might largely accrue to coal buyers

  18. Characteristics of microbial community functional structure of a biological coking wastewater treatment system.

    Science.gov (United States)

    Joshi, Dev Raj; Zhang, Yu; Zhang, Hong; Gao, Yingxin; Yang, Min

    2018-01-01

    Nitrogenous heterocyclic compounds are key pollutants in coking wastewater; however, the functional potential of microbial communities for biodegradation of such contaminants during biological treatment is still elusive. Herein, a high throughput functional gene array (GeoChip 5.0) in combination with Illumina HiSeq2500 sequencing was used to compare and characterize the microbial community functional structure in a long run (500days) bench scale bioreactor treating coking wastewater, with a control system treating synthetic wastewater. Despite the inhibitory toxic pollutants, GeoChip 5.0 detected almost all key functional gene (average 61,940 genes) categories in the coking wastewater sludge. With higher abundance, aromatic ring cleavage dioxygenase genes including multi ring1,2diox; one ring2,3diox; catechol represented significant functional potential for degradation of aromatic pollutants which was further confirmed by Illumina HiSeq2500 analysis results. Response ratio analysis revealed that three nitrogenous compound degrading genes- nbzA (nitro-aromatics), tdnB (aniline), and scnABC (thiocyanate) were unique for coking wastewater treatment, which might be strong cause to increase ammonia level during the aerobic process. Additionally, HiSeq2500 elucidated carbozole and isoquinoline degradation genes in the system. These findings expanded our understanding on functional potential of microbial communities to remove organic nitrogenous pollutants; hence it will be useful in optimization strategies for biological treatment of coking wastewater. Copyright © 2017. Published by Elsevier B.V.

  19. Furnace coking simulations in a laboratory apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Eaton, Paul [Champion Technologies Inc (United States)], email: paul.eaton@champ-tech.com; Newman, Bruce [ConocoPhillips (United States)], email: Bruce.A.Newman@conocophillips.com; Gray, Murray; Kubis, Alan; Derakhshesh, Marzie; Holt, Chris; Mitlin, David [Department of Chemical and Materials Engineering, University of Alberta (Canada)

    2010-07-01

    This work deals with simulating fouling behavior of crude oil in a delayed coker furnace. Fouling on different heated metal probes was investigated; these were mainly stainless steel, iron, or mild steel probes. Heat transfer theory was used to calculate the system fouling factor, and this parameter was recorded as a function of time to model in-situ fouling intensity. Physical and chemical properties such as buildup thickness and composition were investigated using different measuring techniques, most important of which were extractive-iron-nickel ion chromatography, optical and scanning electron microscopy (SEM), and electron dispersion spectroscopy (EDS). Changes in surface layers of the metallic probe during coke formation along with microstructures of the coke were examined using a focused-ion beam (FIB). It was shown that the iron probe exhibited more buildups on its surface than stainless steels, and fouling of mild steel came in between. As for oils with different concentrations, fouling of diluted atmospheric tower bottom (ATB) was greater than that of undiluted ATP.

  20. An empirical study on the preparation of the modified coke and its catalytic oxidation properties

    Science.gov (United States)

    Liu, Hao; Jiang, Wenqiang

    2017-05-01

    T As a methyl acrylic ester fungicide, pyraclostrobin has the advantages of high activity, wide sterilization spectrum and high safety level comparing with the traditional fungicide. Due to less toxicity and side effects on human and environment, the use of pyraclostrobin and its mixture in agriculture is increasing. The heavy use of pyraclostrobin will inevitably cause pollution to the biological and abiotic environment. Therefore, it is of great significance to do the research on the degradation of pyraclostrobin. In this study, coke, as matrix, was modified by chemical modification. The modified coke was used as the catalyst and the pyraclostrobin was used as the degradation object. The degradation experiment of pyraclostrobin was carried out by using catalytic oxidation. The catalytic oxidation performance of modified coke was studied. The result showed that in the catalytic oxidation system of using modified coke as catalyst and H2O2 as oxidant, the best reaction condition is as following: The modified coke which is modified by using 70% concentration nitric acid is used as catalyst; The dosage of the catalyst is10g; The dosage of H2O2 is 0.6ml; The reaction time is 6 hours.

  1. Preparation and characterization of bi-metallic nanoparticle catalyst having better anti-coking properties using reverse micelle technique

    Science.gov (United States)

    Zacharia, Thomas

    Energy needs are rising on an exponential basis. The mammoth energy sources like coal, natural gas and petroleum are the cause of pollution. The large outcry for an alternate energy source which is environmentally friendly and energy efficient is heard during the past few years. This is where “Clean-Fuel” like hydrogen gained its ground. Hydrogen is mainly produced by steam methane reforming (SMR). An alternate sustainable process which can reduce the cost as well as eliminate the waste products is Tri-reforming. In both these reforming processes nickel is used as catalyst. However as the process goes on the catalyst gets deactivated due to coking on the catalytic surface. This goal of this thesis work was to develop a bi-metallic catalyst which has better anti-coking properties compared to the conventional nickel catalyst. Tin was used to dope nickel. It was found that Ni3Sn complex around a core of Ni is coking resistant compared to pure nickel catalyst. Reverse micelle synthesis of catalyst preparation was used to control the size and shape of catalytic particles. These studies will benefit researches on hydrogen production and catalyst manufactures who work on different bi-metallic combinations.

  2. Hysec Process: production of high-purity hydrogen from coke oven gas

    Energy Technology Data Exchange (ETDEWEB)

    Nishida, S

    1984-01-01

    An account is given of the development of the Hysec Process by the Kansai Netsukagaku and Mitsubishi Kakoki companies. The process is outlined and its special features noted. The initial development aim was to obtain high-purity hydrogen from coke oven gas by means of PSA. To achieve this, ways had to be found for removing the impurities in the coke oven gas and the trace amounts of oxygen which are found in the product hydrogen. The resulting hydrogen is 99.9999% pure. 3 references.

  3. The forming of coke by catalytic cracking of black mineral oil by catalysts on the base of activated aluminium alloys

    International Nuclear Information System (INIS)

    Mirzaeva, L.M.; Akhverdiev, R.B.; Aliev, Eh.T.; Gusejnova, A.D.; Gadzhi-Kasumov, V.S.; Akerson, V.I.; Sarmurzina, R.G.

    1995-01-01

    The paper deals with an investigation in coke formation under black mineral oil reactions on oxide catalysts which care based on activated aluminium alloys containing 2-20% of active components of In and Ga. The coke yield is of extreme nature and depends on the content of active components in the catalyst composition. The application of thermogravimetric method shows that the oxidation of coke depositions after black mineral oil cracking proceeds in the same temperature range while after the steam-water treatment of coked catalysts the oxidation of coke deposition proceeds at higher temperatures with different temperature maximums which points to the inhomogeneity of coke depositions. It is shown that the catalyst phase composition changes significantly during the reaction under the effect of reaction mixture. 4 refs., 3 figs

  4. Prediction of operating parameters range for ammonia removal unit in coke making by-products

    Science.gov (United States)

    Tiwari, Hari Prakash; Kumar, Rajesh; Bhattacharjee, Arunabh; Lingam, Ravi Kumar; Roy, Abhijit; Tiwary, Shambhu

    2018-02-01

    Coke oven gas treatment plants are well equipped with distributed control systems (DCS) and therefore recording the vast amount of operational data efficiently. Analyzing the stored information manually from historians is practically impossible. In this study, data mining technique was examined for lowering the ammonia concentration in clean coke oven gas. Results confirm that concentration of ammonia in clean coke oven gas depends on the average PCDC temperature; gas scrubber temperatures stripped liquor flow, stripped liquor concentration and stripped liquor temperature. The optimum operating ranges of the above dependent parameters using data mining technique for lowering the concentration of ammonia is described in this paper.

  5. Crystallinity and shape of crushed calcined coke particles

    International Nuclear Information System (INIS)

    Fecioru, M.; Petrescu, M.; Georgeoni, P.

    1993-01-01

    The particle eccentricity is a very important property of the petroleum coke in determining the anisotropy of the properties of the final graphite and it affects the manner in which its properties change in the specific applications. (orig.)

  6. Crystallinity and shape of crushed calcined coke particles

    Energy Technology Data Exchange (ETDEWEB)

    Fecioru, M. (DACIA Synthetic Diamonds Factory, Bucharest (Romania)); Petrescu, M. (DACIA Synthetic Diamonds Factory, Bucharest (Romania) Polytechnic Inst., Bucharest (Romania)); Georgeoni, P. (DACIA Synthetic Diamonds Factory, Bucharest (Romania))

    1993-11-01

    The particle eccentricity is a very important property of the petroleum coke in determining the anisotropy of the properties of the final graphite and it affects the manner in which its properties change in the specific applications. (orig.).

  7. Differences in the irradiation effects of IG-110 and IG-430 nuclear graphites : effects of coke difference

    International Nuclear Information System (INIS)

    Chi, Se Hwan; Kim, Gen Chan; Kim, Eung Seon; Hong, Jin Ki; Chang, Jong Hwa

    2005-01-01

    In the high temperature gas cooled reactors (HTGRs), graphite acts as a moderator and reflector as well as a major structural component that may provide channels for the fuel and coolant gas, channels for control and shut down, and thermal and neutron shielding. During a reactor operation, many of the physical, chemical and mechanical properties of these graphite components are significantly modified as a function of the temperature, environment, and an irradiation. On the other hand, currently, all the nuclear graphites are being manufactured from two types of cokes, i.e., petroleum and coal-tar pitch coke, and it has been understood that the type of coke plays the most critical role determining the properties of a specific graphite grade. To investigate the effects of coke types on the irradiation response of a graphite, two graphites of different cokes were irradiated by 3 MeV C+ ions and the differences in the response of ion-irradiation were investigated

  8. Refractory compounds for repairing coke-oven brickwork

    Energy Technology Data Exchange (ETDEWEB)

    Hanganu, M.; Dragomir, C. (and others)

    1984-01-01

    A number of refractory compounds are presented, based on aluminium phosphate, phosphoric acid, sodium silicate and fire-clay and mullitic zirconium mastic, including their composition, properties and application (by impregnation, spray application or pouring), which are suitable for repairing various types of coke-oven brickwork. The results obtained are given.

  9. Remediation and demolition of coke by-products plants

    Energy Technology Data Exchange (ETDEWEB)

    Stiffler, M A; Gould, W C

    1992-08-01

    The programme undertaken by ICF Kaiser Engineers and LTV Steel Co. to clean up and demolish four closed coking plants is described, including PCB removal, asbestos abatement, pipe removal and cleaning, tank cleaning, demolition and soil bioremediation. Costs are discussed.

  10. Catalytic effect of lignite ash on steam gasification of oil sand coke

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.; Palmer, A.

    1986-06-16

    Steam gasification of Suncor and Syncrude cokes was carried out in the presence of ash obtained after burning Onakawana lignite. Catalytic effects of the ash were evident at 930 C whereas at 830 C little effect was observed. These observations were attributed to the combined actions of Ca- and Fe-containing species in the ash, in which the former neutralized the sulfur in the cokes to prevent poisoning of Fe oxides. 5 tabs., 5 figs., 15 refs.

  11. Improvements in the construction and operation of coke and other ovens. [Patents

    Energy Technology Data Exchange (ETDEWEB)

    Aitken, H

    1883-01-14

    Into a room above the coke, superheated steam is let in and collects the distillation products throughout the charge into a tube or channel driven into the wall of the retort. The retort walls can be made of a double iron jacket in which water circulates. For emptying the retort, a wedge-shaped plate is used, which is pushed under the coke, thereby the latter is lifted and in large measure moved out of the chamber.

  12. KCBX Petroleum Coke Storage Pile Sampling Logbook and Photos

    Science.gov (United States)

    This documentation of KCBX's petcoke sampling locations and methods demonstrates adherence to the pet coke sampling plan previously submitted and approved by EPA, at both North Terminal and South Terminal stockpiles.

  13. 77 FR 32998 - Foundry Coke From China

    Science.gov (United States)

    2012-06-04

    ... China Determination On the basis of the record \\1\\ developed in the subject five-year review, the United... China would be likely to lead to continuation or recurrence of material injury to an industry in the... Publication 4326 (May 2012), entitled Foundry Coke from China: Investigation No. 731-TA-891 (Second Review...

  14. Fine coke production from brown coal (Report on ECSC contract 6220-72/1/102)

    Energy Technology Data Exchange (ETDEWEB)

    1977-01-01

    The possibility of producing a dry brown coal suitable for the production of fine coke and the development of a suitable carbonization process were studied. To prepare the coal it should be screened at 1 mm with the oversize going to fine coke production and the undersize going to briquette production. To increase fine coke production it is necessary to screen the raw smalls less than 2 mm and to pelletize, dry and carbonize them with the coarser constituents. The planning and construction of a hearth oven furnace plant was begun and this is now in operation. A fluidized bed can be used to preheat the coal to improve the oven performance. (In German)

  15. Sensory evaluation and electronic tongue analysis for sweetener recognition in coke drinks

    Science.gov (United States)

    Szöllősi, Dániel; Kovács, Zoltán; Gere, Attila; Sípos, László; Kókai, Zoltán; Fekete, András

    2011-09-01

    Consumption of beverages with low energy has an increasing role. Furthermore hydrolyzed starch products such as inverted syrup show a wide application in the beverage industry. Therefore the importance of methods which can monitor the usage of natural and artificial sweeteners is increasing. The task was to describe the relevant sensory attributes and to determine the applicability of the electronic tongue to discriminate the coke drink samples with different sweeteners. Furthermore the aim was to find relationship between the taste attributes and measurement results provided by electronic tongue. An Alpha Astree Electronic Tongue and a trained sensory panel were used to evaluate the coke samples. Panelists found significant differences between the samples in 15 cases from the 18 sensory attributes defined previously by the consensus group. Coke drinks containing different kind of sweeteners can be characterized according to these sensory attributes. The samples were definitely distinguished by the electronic tongue. The main difference was found between the samples made with natural and artificial sweeteners. However electronic tongue was able to distinguish samples containing different kind of artificial and different kind of natural sweeteners, as well. Taste attributes of coke drinks determined by sensory panel were predicted by partial least squares regression method based on the results of electronic tongue with close correlation and low prediction error.

  16. Identification of causes of oil sands coke leachate toxicity

    International Nuclear Information System (INIS)

    Puttaswamy, N.; Liber, K.

    2010-01-01

    The potential causes of oil sands coke leachate toxicity were investigated. Chronic 7-day toxicity tests were conducted to demonstrate that oil sands coke leachates (CL) are acutely toxic to Ceriodaphnia dubia (C. dubia). CLs were generated in a laboratory to perform toxicity identification evaluation (TIE) tests in order to investigate the causes of the CL toxicity. The coke was subjected to a 15-day batch leaching process at 5.5 and 9.5 pH values. The leachates were then filtered and used for chemical and toxicological characterization. The 7-day estimates for the C. dubia survival were 6.3 for a pH of 5.5 and 28.7 per cent for the 9.5 CLs. The addition of EDTA significantly improved survival and reproduction in a pH of 5.5 CL, but not in a pH of 9.5 CL. The toxicity of the pH 5.5 CL was removed with a cationic resin treatment. The toxicity of the 9.5 pH LC was removed using an anion resin treatment. Toxicity re-appeared when nickel (Ni) and vanadium (V) were added back to the resin-treated CLs. Results of the study suggested that Ni and V were acting as primary toxicants in the pH 5.5 CL, while V was the primary cause of toxicity in the pH 9.5 CL.

  17. From the Scientific Council of the State Science and Technology Committee on New processes in the coking and chemical industry, Coking and Chemical Products Divisions of the Science and Technological Council of the Ministry of Ferrous Metallurgy of the USSR and Central Plenum of Scientific and Technological Associations of the Ferrous Metallurgy Industry

    Energy Technology Data Exchange (ETDEWEB)

    Ermolova, V.P.

    1985-06-01

    Joint conference took place on 5-7 December 1984 in Moscow. Reports were presented on the following topics: status of implementing the union-wide scientific and technological programs on coking by-products and organizing the production of coke briquet fuel in 1984; developments in the coking and chemical industry up to the year 2000; developing a raw material base for coking up to the year 2000; state of research on thermal processing with hot coke; training engineers for the coking and chemical industry; on planning the work of the scientific council in 1985.

  18. Oxygen-containing coke species in zeolite-catalyzed conversion of methanol to hydrocarbons

    KAUST Repository

    Liu, Zhaohui

    2016-10-06

    Zeolites are the most commonly used catalysts for methanol-to-hydrocarbon (MTH) conversion. Here, we identified two oxygen-containing compounds as coke species in zeolite catalysts after MTH reactions. We investigated the possible influences of the oxygen-containing compounds on coke formation, catalyst deactivation, product selectivity, and the induction period of the MTH reaction through a series of controlled experiments in which one of the identified compounds (2,3-dimethyl-2-cyclopenten-1-one) was co-fed with methanol over a zeolite H-ZSM-5 catalyst. Our results allow us to infer that once produced, the oxygen-containing compounds block the Brønsted acid sites by strong chemisorption and their rapid conversion to aromatics expedites the formation of coke and thus the deactivation of the catalyst. A minor effect of the production of such compounds during the MTH reaction is that the aromatic-based catalytic cycle can be slightly promoted to give higher selectivity to ethylene.

  19. Understanding the mechanisms behind coking pressure: Relationship to pore structure

    Energy Technology Data Exchange (ETDEWEB)

    John J. Duffy; M. Castro Diaz; Colin E. Snape; Karen M. Steel; Merrick R. Mahoney [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre, School of Chemical, Environmental and Mining Engineering

    2007-09-15

    Three low volatile coals A, B and C with oven wall pressures of 100 kPa, 60 kPa and 20 kPa respectively were investigated using high-temperature rheometry, {sup 1}H NMR, thermogravimetric analysis and SEM, with the primary aim to better understand the mechanisms behind the coking pressure phenomenon. Rheometer plate displacement measurements ({Delta}L) have shown differences in the expansion and contraction behaviour of the three coals, which seem to correlate with changes in rheological properties; while SEM images have shown that the expansion process coincides with development of pore structure. It is considered that the point of maximum plate height ({Delta}L{sub max}) prior to contraction may be indicative of a cell opening or pore network forming process, based on analogies with other foam systems. Such a process may be considered important for coking pressure since it provides a potential mechanism for volatile escape, relieving internal gas pressure and inducing charge contraction. For coal C, which has the highest fluidity {delta}L{sub max} occurs quite early in the softening process and consequently a large degree of contraction is observed; while for the lower fluidity coal B, the process is delayed since pore development and consequently wall thinning progress at a slower rate. When {Delta}L{sub max} is attained, a lower degree of contraction is observed because the event occurs closer to resolidification where the increasing viscosity/elasticity can stabilise the expanded pore structure. For coal A which is relatively high fluidity, but also high coking pressure, a greater degree of swelling is observed prior to cell rupture, which may be due to greater fluid elasticity during the expansion process. This excessive expansion is considered to be a potential reason for its high coking pressure. 58 refs., 15 figs., 1 tab.

  20. Research and development of SCOPE21 (super coke oven for productivity and environment enhancement towards the 21st century)

    Energy Technology Data Exchange (ETDEWEB)

    Oshima, H.; Otsuka, J.; Nishioka, K.; Kamijo, T. [Japan Iron and Steel Federation, Tokyo (Japan)

    2000-07-01

    Coke ovens in Japan have 28 years of service on the average and the supply of coke is foreseen to suffer a shortage at the early years of the 21st century. Furthermore, the existing cokemaking process entails a lot of issues such as an effective use of coal resources, an adverse effect on environment. Thus, the Japan Iron and Steel Federation has launched a 9 year research programme called SCOPE 21 in collaboration with the Center for Coal Utilization, Japan in 1994. The programme pursues the following targets. The use ratio of poor coking coal increases from 20-50% with the improvement of coking property of coal by rapid heating and the increase of bulk density by mixing the briquetted coal. The coking time is reduced by rapid heating to 350 to 400{degree}C at the preheater, coking up to 750-850{degree}C at oven chamber, and reheating up to 1000{degree}C at the upgrading chamber, thus trebling productivity. The environment of coke oven is improved by emission free system and by improving the heating system of coke oven to reduce NOx in oven exhaust gas. After two years of preliminary feasible study the programme has advanced to basic research and to a bench scale test. It is in a stage of the construction of a pilot plant. This report describes the outline of the programme and the results obtained through the basic research and the bench scale plant tests. 2 refs., 17 figs., 5 tabs.

  1. Split and collectorless flotation to medium coking coal fines for multi-product zero waste concept

    Energy Technology Data Exchange (ETDEWEB)

    Dey, Shobhana; Bhattacharyya, K.K. [Mineral Processing Division, National Metallurgical Laboratory, Jamshedpur-831007 (India)

    2007-06-15

    The medium coking coal fines of - 0.5 mm from Jharia coal field were taken for this investigation. The release analysis of the composite coal reveals that yield is very low at 10.0% ash, about 25% at 14% ash and 50% at 17% ash level. The low yield is caused by the presence of high ash finer fraction. The size-wise ash analysis of - 0.5 mm coal indicated that - 0.5 + 0.15 mm fraction contains less ash than - 0.15 mm fraction. Thus, the composite feed was split into - 0.5 + 0.15 mm and - 0.15 mm fractions and subjected to flotation separately. The low ash bearing fraction (- 0.5 + 0.15 mm) was subjected to two stages collectorless flotation to achieve the concentrate with 10% ash. The cleaner concentrate (18.9%) with 10% ash was recovered which has an application in metallurgical industries. The concentrate of 30.2% yield with 12.5% ash could be achieved in one stage collectorless flotation which is suitable for use in coke making as sweetener. As the - 0.15 mm fraction contains relatively high ash, collector aided flotation using sodium silicate was performed to get a concentrate of 23.6% yield with about 17% ash. The blending of this product with cleaner tail obtained from - 0.5 + 0.15 mm produces about 35.0% yield with 17% ash and that can be utilized for coke making. The reject from the two fractions can be used for conventional thermal power plant or cement industries using a 23.5% ash after one stage collector aided flotation and the final tailings produced content ash of 61.6% can be used for fluidization combustion bed (FBC). This eventually leads to complete utilization of coal. (author)

  2. Study and modelling of deactivation by coke in catalytic reforming of hydrocarbons on Pt-Sn/Al{sub 2}O{sub 3} catalyst; La microbalance inertielle: etude et modelisation cinetique de la desactivation par le coke en reformage catalytique des hydrocarbures sur catalyseur Pt-Sn/Al{sub 2}O{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Mathieu-Deghais, S.

    2004-07-01

    Catalytic reforming is the refining process that produces gasoline with a high octane number. During a reforming operation, undesired side reactions promote the formation of carbon deposits (coke) on the surface of the catalyst. As the reactions proceed, the coke accumulation leads to a progressive decrease of the catalyst activity and to a change in its selectivity. Getting this phenomenon under control is interesting to optimize the industrial plants. This work aims to improve the comprehension and the modeling of coke formation and its deactivating effect on reforming reactions, while working under conditions chosen within a range as close as possible to the industrial conditions of the regenerative process. The experimental study is carried out with a micro unit that is designed to observe simultaneously the coke formation and its influence on the catalyst activity. A vibrational microbalance reactor (TEOM - Tapered Element Oscillating Microbalance) is used to provide continuous monitoring of coke. On-line gas chromatography is used to observe the catalyst activity and selectivity as a function of the coke content. The coking experiments are performed on a fresh Pt-Sn/alumina catalyst, with mixtures of hydrocarbon molecules of 7 carbon atoms as hydrocarbon feeds. The coking tests permitted to highlight the operating parameters that may affect the amount of coke, and to identify the hydrocarbon molecules that behave as coke intermediate. A kinetic model for coke formation could be developed through the compilation of these results. The catalytic activity analysis permitted to point out the coke effect on both of the active phases of the catalyst, to construct a simplified reforming kinetic model that simulates the catalyst activity under the reforming conditions, and to quantify deactivation via deactivation functions. (author)

  3. "The Real Thing:" Nominal Price Rigidity of the Nickel Coke, 1886-1959

    OpenAIRE

    Daniel Levy; Andrew T. Young

    2004-01-01

    We report that the price of a 6.5oz Coke was 5¢ from 1886 until 1959. Thus, we are documenting a nominal price rigidity that lasted more than 70 years! The case of Coca-Cola is particularly interesting because during the 70-year period there were substantial changes in the soft drink industry as well as two World Wars, the Great Depression, and numerous regulatory interventions and lawsuits, which led to substantial changes in the Coca-Cola market conditions. The nickel price of Coke, neverth...

  4. Coke oven gas to methanol process integrated with CO_2 recycle for high energy efficiency, economic benefits and low emissions

    International Nuclear Information System (INIS)

    Gong, Min-hui; Yi, Qun; Huang, Yi; Wu, Guo-sheng; Hao, Yan-hong; Feng, Jie; Li, Wen-ying

    2017-01-01

    Highlights: • CO_2 recycle assistance with COG to CH_3OH with dry reforming is proposed. • New process with dry reforming improves H_2 utilization and energy saving. • Process with H_2 separation (CWHS) is more preferable to CH_3OH output. • CWHS shows an excellent performance in energy, economy and CO_2 emission reduction. - Abstract: A process of CO_2 recycle to supply carbon for assisting with coke oven gas to methanol process is proposed to realize clean and efficient coke oven gas utilization. Two CO_2 recycle schemes with respect to coke oven gas, namely with and without H_2 separation before reforming, are developed. It is revealed that the process with H_2 separation is more beneficial to element and energy efficiency improvement, and it also presents a better techno-economic performance in comparison with the conventional coke oven gas to methanol process. The exergy efficiency, direct CO_2 emission, and internal rate of return of the process with H_2 separation are 73.9%, 0.69 t/t-methanol, and 35.1%, respectively. This excellent performance implies that reforming technology selection, H_2 utilization efficiency, and CO_2 recycle ways have important influences on the performance of the coke oven gas to methanol process. The findings of this study represent significant progress for future improvements of the coke oven gas to methanol process, especially CO_2 conversion integrated with coke oven gas utilization in the coking industry.

  5. Current developments at Giprokoks for coke-battery construction and reconstruction

    Energy Technology Data Exchange (ETDEWEB)

    V.I. Rudyka; Y.E. Zingerman; V.B. Kamenyuka; O.N. Surenskii; G.E. Kos' kova; V.V. Derevich; V.A. Gushchin [Giprokoks, the State Institute for the Design of Coke-Industry Enterprises, Kharkov (Ukraine)

    2009-07-15

    Approaches developed at Giprokoks for coke-battery construction and reconstruction are considered. Recommendations regarding furnace construction and reconstruction are made on the basis of Ukrainian and world experience.

  6. Developpement d'un modele thermodynamique pour les cristallites de coke: Application aux systems carbone-hydrogene et carbone-soufre

    Science.gov (United States)

    Ouzilleau, Philippe

    Carbon materials are essential components of multiple key industrial processes. One example of such a process is the production of aluminum using the Hall-Heroult process. It is well known that important quantities of carbon materials are regularily consumed by the operation of the Hall-Heroult process. In recent years, the increased impurity content of industrial carbon materials motivated the development of a better understanding for the high temperature behavior of these specific materials. The most common forms of carbon materials used in the industry are cokes. Cokes are carbon materials which, following heat treatment, present a crystalline structure similar to that observed in graphite. However, the observed crystallite size of cokes is usually much smaller than the one observed in graphite. For this reason, the chemical and thermodynamic properties of the ordered phase of cokes (i.e. coke crystallites) are very different than those of graphite (although coke crystallites of infinite size would possess properties almost identical to graphite). Coke crystallites consist of hexagonal planes of carbon atoms stacked one above the other. This particular aspect causes strong anisotropic properties in coke crystallites. No thermodynamic model was found for the production of a reliable correlation between the effect of crystallite size and chemical composition for the predictive calculations of the thermodynamic properties (and phase equilibriums) of coke crystallites. It is also difficult to produce predictive calculations that can be compared to experimental results using such a thermodynamic model. The goal of the present work is to propose a thermodynamic model designed to solve this problem. The present model is based on the well-defined geometrical properties of coke cristallites. This geometry allows the development of mathematical equations for the calculation of the mass balances of the crystallite (using a simplified geometry) using only the commonly used

  7. Emission characteristics and size distribution of polycyclic aromatic hydrocarbons from coke production in China

    Science.gov (United States)

    Mu, Ling; Peng, Lin; Liu, Xiaofeng; He, Qiusheng; Bai, Huiling; Yan, Yulong; Li, Yinghui

    2017-11-01

    Coking is regarded as a major source of atmospheric polycyclic aromatic hydrocarbons (PAHs), but few researches have been conducted on the emission characteristics of PAHs from coke production. In this study, emissions of size-segregated particulate matter (PM) and particle-bound PAHs emitted from charging of coal (CC) and pushing of coke (PC) in four typical coke plants were determined. The emission factors on average, sums of CC and PC, were 4.65 mg/kg, 5.96 mg/kg, 19.18 μg/kg and 20.69 μg/kg of coal charged for PM2.1 (≤ 2.1 μm), PM, PAHs in PM2.1 and total-PAHs, respectively. PM and PAHs emission from plants using stamp charging were significantly more than those using top charging. The profile of PAHs in PM with size ≤ 1.4 μm (PM1.4) emitted from CC process were similar with that from PC, however, it revealed obviously different tendency for PAHs in PM with size > 1.4 μm, indicating the different formation mechanism for coarse particles emitted from CC and PC. Size distributions of PM and PAHs indicated that they were primarily connected with PM1.4, and the contributions of PM1.4 to PM and PAHs emitted from the plants using stamp charging were higher than those using top charging. Some improved technology in air-pollution control devices should be considered in coke production in future based on the considerable impacts of PM1.4 and PAHs on human health and ambient air quality.

  8. An additive for a petroleum coke and water suspension

    Energy Technology Data Exchange (ETDEWEB)

    Khiguti, K.; Igarasi, T.; Isimura, Y.; Kharaguti, S.; Tsudzina, T.

    1983-03-04

    The patent covers an additive for a petroleum coke and watersuspension which contains soap of an aliphatic acid (AM) and or a salt of a maleic acid copolymer (SMK). The aliphatic acid soap is a salt of an alkaline earth metal of C6 to C22 aliphatic acid, an ammonium salt or a salt of a lower amine. The maleic acid copolymer is a salt (sodium, NH4) of a lower amine of a maleic anhydride copolymer with a copolymerizing vinyl additive. Capric acid, lauric acid, palmatic acid, aleic and other acids may be used as the aliphatic acid, while methylamine, trimethylamine, diethanolamine, morpholine and so on may be used as the lower amine salt. Ethylene, vinylchloride, methyl(meta)acrylate and so on are used as the polymerizing vinyl compound. The molar ratio of the maleic anhydride to the polymerizing vinyl compound is in a range from 1 to 1 to 1 to 10 (preferably 1 to 1 to 1 to 3). The maleic acid copolymer has a mean molecular mass within 1,000 to 5,000. The additive with the optimal composition contains a solvent, a thickener, an anticorrosion substance, anticoagulants, surfacants (PAV) and so on. A highly concentrated suspension of oil coke and water with a 50 to 75 percent concentration of powder form petroleum coke may be produced using the patented additive. Such a suspension is characterized by low viscosity, high stability and forms no foam during processing.

  9. Process and apparatus for pyrolytic decomposition and coking of mixtures of finely divided solid carbonaceous material and hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    Fisher, A

    1933-09-18

    A process is described for pyrolytic decomposition and coking of mixtures of finely divided solid and semi-solid carbonaceous material and hydrocarbon oils, whereby the mixture is first heated to a high temperature; the heated products are introduced into a coking zone, where vapors are separated from nonvaporous residue afterwards to be cracked and condensed, characterized in that the mixture is heated to a high temperature under substantially noncoking conditions and that nonvaporous residue obtained in the coking zone is coked as a relatively thin layer on an externally intensely heated surface, preferably of heat-conducting, fireproof material, such as carborundum, fused-aluminum oxide, or clay.

  10. The Dawes Lane coke ovens by-products plant expert system

    Energy Technology Data Exchange (ETDEWEB)

    P. Warren [Corus Research Development and Technology (United Kingdom). Teeside Technology Department

    2002-07-01

    A system has been developed to provide comprehensive monitoring of the washer/scrubber processes on the by-products plant at Dawes Lane coke ovens where faulty operation may cause blockage of the gas stream leading to opening of the battery bleeders to release gas to atmosphere. The system developed and the additional instrumentation and practices have met the requirements for improved monitoring to reduce the likelihood of uncontrolled gas emissions. It is planned to further develop the system so that it will contribute towards optimisation of plant operation, and so to generate a financial benefit from the investment made. The paper was presented to the Midland Section of the Coke Oven Managers' Association at Corus Centre, Scunthorpe, UK on 20 May 2001. 11 figs., 1 tab.

  11. The development of coke smelting and the industrial revolution

    OpenAIRE

    Macfarlane, Alan

    2004-01-01

    Abraham Darby and the origins of the industrial revolution in Britain. Alan Macfarlane talks to John about the reasons for the area near Birmingham becoming the epi-centre of the industrial development, and the development of coke furnaces and iron smelting.

  12. [Evaluating work intensity in major and auxiliary occupations of by-product coke industry].

    Science.gov (United States)

    Smagulov, N K; Alpysbayeva, Zh T

    2015-01-01

    The article covers evaluation of work strain in major and auxiliary occupations of by-product coke industry. The study results conclude that occupational activity of by-product coke industry workers, under exposure to occupational hazards, affects the workers' performance. Major occupations workers demonstrate higher level of functional strain of CNS, poor concentration of attention and lower ability to switch over, decreased general performance, vs. the auxiliary occupations workers who demonstrated increased cardiovascular and neuro-muscular strain due to occupational activity.

  13. Scientific principles underlying the production of metallurgy-grade formed coke from weakly baking coals. Nauchnye osnovy proizvodstva formovannogo metallurgicheskogo koksa iz slabospekayushchikhsya uglei

    Energy Technology Data Exchange (ETDEWEB)

    Speranskaya, G.V.; Tyutyunnikov, Yu.B.; Erkin, L.I.; Nefedov, P.Ya.; Sheptovitskii, M.S.; Toryanik, E.I.

    1987-01-01

    Coking coal resources of the USSR are nonuniformly distributed among major coal basins (Donetsk 26%, Pechora 7%, Kizelovsk and L'vov-Volyn' 0.5% each, Kuznetsk 48.2%, Karaganda 7%, South Yakutiya 4.4%, others 7.4%). Only one-third of the resources are available in the European area of the USSR where the demand for blast-furnace coke is greater. The use of weakly baking and nonbaking coals for the production of metallurgy-grade formed coke has been found to be the simplest way to avoid transportation of fat components of coking blends and to cut the cost of pig iron production under Soviet circumstances. Commercial production of the formed coke should enable the blast-furnace coke production to be raised by 15 Mio t/a now and by 20-22 Mio t/a in the nearest future without the structure of the Soviet coal production being significantly affected. The book describes technical properties of the gas, weakly baking and long-flame coals (G, SS and D types, respectively) from Donetsk, Kuznetsk, Irkutsk and Karaganda coal basins used as coking blend components, discusses many scientific and technological aspects of the industrial-scale process (i.e. thermal pretreatment of coal with a gaseous heat-carrier, effect of pressure on the plastic layer formation in weakly baking coal blends, coke oven construction), and reviews technical properties of formed coke (shape and size of coke lumps, drum strength, macro- and microstructure, thermal stability, reactivity) used in the blast-furnace process. 122 refs., 118 figs., 87 tabs.

  14. Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

    Science.gov (United States)

    The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

  15. Torrefaction reduction of coke formation on catalysts used in esterification and cracking of biofuels from pyrolysed lignocellulosic feedstocks

    Science.gov (United States)

    Kastner, James R; Mani, Sudhagar; Hilten, Roger; Das, Keshav C

    2015-11-04

    A bio-oil production process involving torrefaction pretreatment, catalytic esterification, pyrolysis, and secondary catalytic processing significantly reduces yields of reactor char, catalyst coke, and catalyst tar relative to the best-case conditions using non-torrefied feedstock. The reduction in coke as a result of torrefaction was 28.5% relative to the respective control for slow pyrolysis bio-oil upgrading. In fast pyrolysis bio-oil processing, the greatest reduction in coke was 34.9%. Torrefaction at 275.degree. C. reduced levels of acid products including acetic acid and formic acid in the bio-oil, which reduced catalyst coking and increased catalyst effectiveness and aromatic hydrocarbon yields in the upgraded oils. The process of bio-oil generation further comprises a catalytic esterification of acids and aldehydes to generate such as ethyl levulinate from lignified biomass feedstock.

  16. Effect of moisture on the accuracy of coke-ash determination by X-ray backscattering

    International Nuclear Information System (INIS)

    Pandey, H.D.; Prasad, M.S.

    1984-01-01

    Effect of moisture on the rapid non-destructive estimation of ash content in coal specimens using the X-ray backscattering technique has been studied extensively by various workers. In the present work, an attempt has been made to estimate its influence when the technique is extended to coke-ash determinations. From the study of the variation of backscattered intensity with change in the moisture content of a coke specimen, it is observed that the ash content varies significantly at moisture levels higher than 5%. The variation, however, remains within allowable limits if the moisture level is kept below 5%. This observation is confirmed by the actual measurement of ash percentages in thirteen coke specimens containing three different states of moisture levels viz. (i) in the dry state, (ii) with 5% moisture and (iii) with 10% moisture. (author)

  17. Retort for coking peat, brown coal, bituminous shale, etc

    Energy Technology Data Exchange (ETDEWEB)

    1902-05-14

    The retort leads the gases and vapors into the coking chamber, between the inside heater and the outer heating shaft-wall. Over-lapping, double-faced acting rings are arranged, over which the charge in two or more separate vertical layers is transported.

  18. Impact of co-combustion of petroleum coke and coal on fly ash quality: Case study of a Western Kentucky power plant

    International Nuclear Information System (INIS)

    Hower, James C.; Thomas, Gerald A.; Mardon, Sarah M.; Trimble, Alan S.

    2005-01-01

    Petroleum coke has been used as a supplement or replacement for coal in pulverized-fuel combustion. At a 444-MW western Kentucky power station, the combustion of nearly 60% petroleum coke with moderate- to high-sulfur Illinois Basin coal produces fly ash with nearly 50% uncombusted petroleum coke and large amounts of V and Ni when compared to fly ash from strictly pulverized coal burns. Partitioning of the V and Ni, known from other studies to be concentrated in petroleum coke, was noted. However, the distribution of V and Ni does not directly correspond to the amount of uncombusted petroleum coke in the fly ash. Vanadium and Ni are preferentially associated with the finer, higher surface area fly ash fractions captured at lower flue gas temperatures. The presence of uncombusted petroleum coke in the fly ash doubles the amount of ash to be disposed, makes the fly ash unmarketable because of the high C content, and would lead to higher than typical (compared to other fly ashes in the region) concentrations of V and Ni in the fly ash even if the petroleum coke C could be beneficiated from the fly ash. Further studies of co-combustion ashes are necessary in order to understand their behavior in disposal

  19. Baking and coking properties of hard coal under high pressure

    Energy Technology Data Exchange (ETDEWEB)

    Beyer, H.D.

    1981-09-01

    For a better assessment of the baking and coking properties of hard coal under high pressure as in modern coal beneficiation processes, the determination of the swelling index and the dilatation curve are investigated.

  20. Determining sulfur in metallurgical coke by the X-ray fluorescent method

    Energy Technology Data Exchange (ETDEWEB)

    Sofilic, T.; Kesic-Racan, M.; Sindler, M.; Sokolean, D.

    1979-01-01

    A method is described of X-ray fluorescent analysis for current determination of sulfur in the concentration range of 0.5-1.16% in metallurgical coke. To do this, the analyzed material (coke) is ground to a particle size of 200 mu and mixed in a 1:1 ratio with an organic binder (soluble starch). The mixture is briquetted in meshes of a certain size under a pressure of 25 tons/cm/sub 2/. The tablets obtained are analyzed in a Phillips spectrometer with a Cr anticathode. The presence is noted of a linear dependence between the S content and the instrument reading; the correlation factor is 0.91; the mean detection error, 0.0596.

  1. 41 CFR 101-26.4904-416 - DD Form 416: Purchase Request for Coal, Coke, or Briquettes.

    Science.gov (United States)

    2010-07-01

    ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true DD Form 416: Purchase Request for Coal, Coke, or Briquettes. 101-26.4904-416 Section 101-26.4904-416 Public Contracts and... DD Form 416: Purchase Request for Coal, Coke, or Briquettes. Note: The form illustrated in § 101-26...

  2. Renewable synthesis-gas-production. Do hydrocarbons in the reactant flow of the reverse water-gas shift reaction cause coke formation?

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, A.; Kern, C.; Jess, A. [Bayreuth Univ. (Germany). Dept. of Chemical Engineering

    2013-11-01

    In a two-step synthetic fuel production process based on carbon dioxide and renewable hydrogen, the best possible selectivity towards liquid hydrocarbons (Hc) shall be implemented. The process consists of a combination of the Reverse Water-Gas Shift reaction and the Fischer-Tropsch synthesis. To achieve this goal, gaseous short-chained Hc from the FTS reactor are recycled in the RWGS unit. In this paper, challenges coming up with the implementation of a recycle loop are discussed. First of all, it has to be examined whether Hc are converted under conditions present in the RWGS reactor. The coking caused by the recycle of Hc is regarded, including thermal coking in the heating zone of the reactor and catalytic coking in the catalyst bed. Coking of course is unwanted, as it deactivates the catalyst. The scope of this work is to find out to which extent and under which conditions gaseous Hc can be recycled. Therefore, experiments were carried out in both, a quartz glass reactor using a commercial Ni-catalyst at ambient pressure and in a pressurized steel reactor (without catalyst) to examine coking during the thermal decomposition of Hc. The catalytic experiments at atmospheric pressure showed that a recycle of CH{sub 4} did not cause coking up to a ratio of CH{sub 4}/CO{sub 2} below one. For these conditions, long term stability was proved. The reaction rates of the CH{sub 4} conversion were below those of the RWGS reaction. However, replacing CH{sub 4} by C{sub 3}H{sub 8} leads to thermal and catalytic coking. Catalytic coking hits the maximum level at about 700 C and decreases for higher temperatures and, thus is not regarded as a problem for the RWGS reactor. In contrast to that, thermal coking raises with higher temperatures, but it can be supressed efficiently with additional injection of H{sub 2}O, which of course shifts the equilibrium towards the undesired reactant side. (orig.)

  3. In the coking section of the Scientific Council of the Main Committee for Science and Technology 'New processes in ferrous metallurgy'

    Energy Technology Data Exchange (ETDEWEB)

    Bukvareva, O.F.

    1989-12-01

    Reports on a meeting held in June 1990 in Khar'kov on new technologies of black coal coking and methods for coal gas purification used in the USSR and other countries. The following problems associated with economic analysis of new coking technologies were analyzed: types of coal used in mixtures for coking, mixtures for coking, coal mixture preheating, partial briquetting. The following problems associated with coal gas purification were discussed: primary cooling systems, methods for ammonia separation from coal gas, coal gas desulfurization, separation of hydrogen cyanide, amine methods for desulfurization. Recommendations for research programs on new coking technologies and on coal gas purification are discussed.

  4. Effect of oxygen potential on sulphur dioxide activation of oil sands fluid coke and characteristics of activated coke in mercury adsorption

    International Nuclear Information System (INIS)

    Morris, E.A.; Jia, C.Q.; Tong, S.

    2007-01-01

    A sulphur-impregnated activated carbon (SIAC) technology was modified for use in copper smelters in order to mitigate mercury and sulphur dioxide (SO 2 ) emissions. Elemental sulphur was captured as a co-product. The study examined the feasibility of reducing levels of SO 2 using fluid coke in the copper smelter flue. SIAC properties were optimized in order to capture vapour phase mercury. Raw fluid coke samples were used to measure SO 2 flow rates. Gas composition was varied to mimic concentrations found during normal operation of copper converters. Gas chromatography was used to analyze reactions products and to prove the hypothesis that mercury capacity is influenced by the oxygen potential of the activation gas due to changes in surface sulphur types developed from reduced sulphur species. Results of the study showed that oxygen levels at 5 per cent did not play a significant role in pore development. It was concluded that increased residence times contributed to reductions in SO 2 and elemental S yields. 13 refs., 1 tab., 7 figs

  5. On-Line Fuel Deoxygenation for Coke Suppression ASME GT-2002-30071

    National Research Council Canada - National Science Library

    Spadaccini, Louis

    2002-01-01

    Fuel deoxygenation is being developed as a means for suppressing autoxidative coke formation in aircraft fuel systems, thereby increasing the exploitable cooling capacity of the fuel, enabling major...

  6. Clean utilization of high sulphur petroleum coke by circulating fluidized bed combustion (CFBC) in Romania

    International Nuclear Information System (INIS)

    Dragos, L.; Flueraru, C.; Girjoaba, M.

    1996-01-01

    The economic and environmental problems caused by inefficient utilization of residual high-sulphur petroleum coke resulted from oil cracking in Romania is discussed. A special research programme applying CFBC technology has been carried out in the Institute for Power Equipment, Bucharest. The results from both laboratory facilities and pilot plant are presented. The main operating conditions and parameters are pointed out. Data on quality and composition of petroleum coke, combustion efficiency, temperature range in different zones and flue gas composition at distinct operating loads are given. The results obtained will be used for innovative design of CFBC boilers based on petroleum coke. A project for implementing a CFBC boiler in one of the Romanian oil refineries is being developed. An analysis of technical and economic advantages of these boilers for energy generation is presented

  7. Prospects for the use of coke-works gas in the manufacture of sponge iron

    Energy Technology Data Exchange (ETDEWEB)

    Hatarascu, O; Orosz, R

    1978-01-01

    This paper presents the results of tests conducted in the laboratory of the I.C.E.M. (National research institute for the mining industry) at Hunedoara; these investigations dealt with the reduction of iron oxide by gas from coking plant. The direct application of coke-works gas for the direct reduction of iron ores represents a new move towards the profitable utilization of this gas which, owing to its high content of hydrogen and CH4, can be transformed into CO and H2 using current conversion techniques (water-vapour or CO2 methods). The article presents a diagram of the 'MIDREX' reduction plant. Also includes a study of the variation in the specific coke-gas consumption as a function of the reducer-gas throughput together with an analysis of the reduction process for recycled and regenerated gas at a temperature of 900 C.

  8. U.S. origin coking coal in the global market : a seismic shift in the global coal market

    International Nuclear Information System (INIS)

    Thrasher, E.

    2010-01-01

    This presentation discussed conditions in the global coal market and its impact on producers in the United States (U.S). The significant factors include the strong recovery in Asia, the switch from annual benchmark pricing to quarterly pricing, and the return of U.S. origin coking coal as a long-term supply source for Asia. The global recovery in manufacturing is strong in Asia and weak in more mature economies. A shift in trade patterns has occurred in that 4 of the top 10 destinations for U.S. coking coal exports are now in Asia, up from 1 in 2009, and the tonnage increases to these destinations are at unprecedented levels. Demand for U.S. origin coal will continue to increase as the economies in Western Europe improve and the emerging economies in Eastern Europe and South America grow. Looking at the U.S. coking coal supply, high volume type A coal will be used in the domestic market while high volume type B coal will be used for international demand. Government regulatory agencies create an uncertain environment for investments. Geology and the effects of regulatory actions have decreased productivity. An improvement to the supply chain is that lower cost ocean freight lowers the cost of delivered coal. The prices of coking coal have stabilized at levels that support reasonable returns on investment. The seaborne coking coal market has changed with China's shift to being a significant importer. Mine, rail, and port capacity will constrain the ability of producers in the U.S. to export coking coal to some degree. 2 tabs., 13 figs.

  9. A novel approach to mitigating sulphur dioxide emissions and producing a mercury sorbent material using oil-sands fluid coke

    International Nuclear Information System (INIS)

    Morris, E.; Jia, C.Q.; Tong, S.

    2008-01-01

    Pyrometallurgical smelting operations are a major source of sulphur dioxide (SO 2 ) which is a precursor to acid rain and increased levels of UV-B penetration in boreal lakes. Mercury is also released in copper smelter off-gas, which can bioaccumulate and cause neurological disorders and death in humans. Fluid coke is produced in massive quantities as a by-product of bitumen upgrading at Syncrude Canada's facility in Fort McMurray, Alberta. Oilsands fluid coke can be used to reduce SO 2 and produce elemental sulphur as a co-product. This process was dubbed SOactive. The reaction physically activates the fluid coke to produce a sulphur-impregnated activated carbon (SIAC) which is known as ECOcarbon. Some studies have indicated that SIAC is well suited for the removal of vapour phase mercury, mainly due to the formation of stable mercuric sulphide species. This paper discussed the findings made to date in relation to the SOactive process and the characterization of ECOcarbons. The paper discussed the use of fluid coke for reducing SO 2 emissions while producing elemental sulphur as well as coke-SO 2 -oxygen (O 2 ) and coke-SO 2 -water (H 2 O) systems. The paper also examined the production of SIAC products for use in capturing vapour phase mercury. The paper presented the materials and methodology, including an illustration of the apparatus used in reduction of SO 2 and activation of fluid coke. It was concluded that more work is still needed to analyse the effect of O 2 and SO 2 reduction and SIAC properties under smelter flue gas conditions. 10 refs., 1 tab., 8 figs

  10. Reaction Mechanism for the Formation of Nitrogen Oxides (NO x ) During Coke Oxidation in Fluidized Catalytic Cracking Units

    KAUST Repository

    Chaparala, Sree Vidya; Raj, Abhijeet; Chung, Suk-Ho

    2015-01-01

    and accurate kinetics for NOx formation. Based on the nitrogen-containing functional groups on coke, model molecules are selected to study reactions between coke-bound nitrogen and O2 to form NO and NO2 using density functional theory. The reaction kinetics

  11. Statistical summary of coal mining, coking, and briquetting plants and review of the solid fuels market in 1976

    Energy Technology Data Exchange (ETDEWEB)

    Medaets, J

    1977-05-01

    This paper reviews the activities of the Belgian coal and coke industry noting that some of the figures are still provisional. Figures are given for production and stocks of coal; personnel; productivity; working hours; salaries; and the production of coke and briquettes.

  12. Multinuclear MAS NMR studies on coked zeolites H-ZSM-5

    International Nuclear Information System (INIS)

    Ernst, H.; Freude, D.; Hunger, M.; Pfeifer, H.

    1991-01-01

    During the cracking process carbonaceous materials are deposited on the outer or inner surface of the catalyst. These deposits are in many cases the main cause of catalyst deactivation. Magic angle spinning (MAS) NMR investigations and catalytic n-hexane cracking were carried out on H-ZSM-5 zeolites after a mild hydrothermal de-alumination. By 13 C CP MAS NMR it could be shown that the enhanced catalytic activity does not enhance the coke formation and that the chemical nature of these deposits is essentially aromatic. From 1 H MAS NMR studies performed on shallow-bed activated sealed samples and 27 Al and 29 Si MAS NMR on rehydrated samples it follows that for high coke concentrations the catalyst deactivation is caused mainly by blocking of Broensted acid sites. (author). 27 refs.; 3 figs.; 2 tabs

  13. Partial briquetting of coal charges as a means of utilizing lower-grade coal for coke making

    Energy Technology Data Exchange (ETDEWEB)

    Pieters, B.J. (Iscor Limited, Newcastle (South Africa))

    1991-08-01

    The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briquetted charges, and it was decided to install briquetting plants at the Vanderbijlpark and Newcastle Works. Details are given of the latter plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity. 11 figs., 3 tabs.

  14. 40 CFR Appendix A to Subpart L of... - Operating Coke Oven Batteries as of April 1, 1992

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Operating Coke Oven Batteries as of April 1, 1992 A Appendix A to Subpart L of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION... SOURCE CATEGORIES National Emission Standards for Coke Oven Batteries Pt. 63, Subpt. L, App. A Appendix A...

  15. Modified sequential extraction for biochar and petroleum coke: Metal release potential and its environmental implications.

    Science.gov (United States)

    von Gunten, Konstantin; Alam, Md Samrat; Hubmann, Magdalena; Ok, Yong Sik; Konhauser, Kurt O; Alessi, Daniel S

    2017-07-01

    A modified Community Bureau of Reference (CBR) sequential extraction method was tested to assess the composition of untreated pyrogenic carbon (biochar) and oil sands petroleum coke. Wood biochar samples were found to contain lower concentrations of metals, but had higher fractions of easily mobilized alkaline earth and transition metals. Sewage sludge biochar was determined to be less recalcitrant and had higher total metal concentrations, with most of the metals found in the more resilient extraction fractions (oxidizable, residual). Petroleum coke was the most stable material, with a similar metal distribution pattern as the sewage sludge biochar. The applied sequential extraction method represents a suitable technique to recover metals from these materials, and is a valuable tool in understanding the metal retaining and leaching capability of various biochar types and carbonaceous petroleum coke samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. The use of fractionated fly ash of thermal power plants as binder for production of briquettes of coke breeze and dust

    Science.gov (United States)

    Temnikova, E. Yu; Bogomolov, A. R.; Lapin, A. A.

    2017-11-01

    In this paper, we propose to use the slag and ash material of thermal power plants (TPP) operating on pulverized coal fuel. The elemental and chemical composition of fly ash of five Kuzbass thermal power plants differs insignificantly from the composition of the mineral part of coking coal because coke production uses a charge, whose composition defines the main task: obtaining coke with the required parameters for production of iron and steel. These indicators are as follows: CRI reactivity and strength of the coke residue after reaction with CO2 - CSR. The chemical composition of fly ash of thermal power plants and microsilica with bulk density of 0.3-0.6 t/m3 generated at production of ferroalloys was compared. Fly ash and microsilica are the valuable raw material for production of mineral binder in manufacturing coke breeze briquettes (fraction of 2-10 mm) and dust (0-200 μm), generated in large quantities during coking (up to 40wt%). It is shown that this binder is necessary for production of smokeless briquettes with low reactivity, high strength and cost, demanded for production of cupola iron and melting the silicate materials, basaltic rocks in low-shaft furnaces. It is determined that microsilica contains up to 90% of silicon oxide, and fly ash contains up to 60% of silicon oxide and aluminum oxide of up to 20%. On average, the rest of fly ash composition consists of basic oxides. According to calculation by the VUKHIN formula, the basicity index of briquette changes significantly, when fly ash is introduced into briquette raw material component as a binder. The technology of coke briquette production on the basis of the non-magnetic fraction of TPP fly ash in the ratio from 3.5:1 to 4.5:1 (coke breeze : coke dust) with the addition of the binder component to 10% is proposed. The produced briquettes meet the requirements by CRI and require further study on CSR requirements.

  17. Comparison of 3 MeV C+ Ion-Irradiation Effects between The Nuclear Graphites made of Pitch and Petroleum Cokes

    International Nuclear Information System (INIS)

    Se-Hwan, Chi; Gen-Chan, Kim; Jong-Hwa, Chang

    2006-01-01

    Currently, all the commercially available nuclear graphite grades are being made from two different cokes, i.e., petroleum coke or coal-tar pitch coke, and a coal-tar pitch binder. Of these, since the coke composes most of the graphite volume, i.e., > 70 %, it is understood that a physical, chemical, thermal, and mechanical property as well as an irradiation-induced property change will be strongly dependent on the type of coke. To obtain first-hand information on the effects of the coke type, i.e., petroleum or pitch, on the irradiation sensitivity of graphite, specimens made of IG-110 of petroleum coke and IG-430 of pitch coke were irradiated up to ∼ 19 dpa by 3 MeV C + at room temperature, and the irradiation-induced changes in the hardness, Young's modulus, Raman spectrum, and oxidation properties were characterized. Results of the TEM show that the size and density of the Mrozowski cracks appeared to be far larger and higher in the IG-110 than the IG-430. Results of the hardness test revealed a slightly higher increase in the IG-430 than the IG-110 by around 10 dpa, and the Raman spectrum measurement showed a higher (FWHM) D /(FWHM) G value for IG-430 for 0.02 ∼ 0.25 dpa. Both the hardness and Raman measurement may imply a higher irradiation sensitivity of the IG-430 than the IG-110. Results of the Young's modulus measurements showed a large data scattering, which prevented us from estimating the differences between the grades. Oxidation experiments using a TG-DTA under a flow of dry air/He = 2.5 % (flow rate: 40 CC/min) at 750 and 1000 deg C show that the IG-110 of the petroleum coke exhibits a far higher oxidation rate than the IG-430. The discrepancy between the oxidation rate of the two grades increased with an increase in the oxidation temperature and the dose. Oxidized surface pore area was larger for IG-110. Judging from the results obtained from the present experimental conditions, the irradiation sensitivity appeared to be dependent on the degree

  18. Characterization of Coke on a Pt-Re/γ-Al _2 O _3 Re-Forming Catalyst: Experimental and Theoretical Study

    International Nuclear Information System (INIS)

    Bare, Simon R.; Vila, F. D.; Prabhakar, Sesh; Bradley, William J.

    2017-01-01

    The characterization of coke on spent catalysts is key to understanding deactivation mechanisms in hydrocarbon transformations. Here, we report the comprehensive characterization (using laser Raman spectroscopy, "1"3C MAS NMR, temperature-programmed oxidation, XPS, and carbon K-edge NEXAFS) of coke on a series of spent Pt-Re re-forming catalysts as a function of time on stream and position in the catalytic bed. Laser Raman spectroscopy is shown to be rather insensitive to the carbon species present, while "1"3C MAS NMR finds that the carbon is present primarily as aromatic carbon. The TPO data are consistent with the coke being present on the alumina support and not to a large extent covering the metallic Pt-Re nanoclusters, but the data do suggest the presence of more than one type of coke present. The carbon K-edge NEXAFS data, however, clearly differentiate the types of coke species present. In the more coked samples the features ascribed to graphite become more pronounced, together with an increase in the aromaticity, as judged by the intensity of the π* peak. With increasing amounts of carbon on the catalyst there is also a concomitant decrease in the σ* C–H peak, indicating that the carbon is becoming less hydrogenated. Furthermore, by using a linear combination of C NEXAFS spectra for n-hexane, benzene, and broadened highly oriented pyrolytic graphite (HOPG), we estimate the compositional change on the coke species, verifying the aliphatic to aromatic conversion. The data indicate that a good model for the deposited coke is that of highly defected, medium-sized rafts with a short-range polycyclic aromatic structure which have a variety of points of contact with the alumina surface, in particular with the O atoms. In agreement with the NMR, there is evidence for the C–O functionality from the presence of a shoulder in the C NEXAFS spectra that is ascribed, as a result of DFT calculations, to a 1s → π* transition of the carbon atoms bound to the

  19. Japanese coke plant follows US lead

    Energy Technology Data Exchange (ETDEWEB)

    1980-06-01

    Nippon Steel has acquired the first licence for a US Steel/Firma Carl Still process for cleaning coke oven flushing liquor. The process is installed at 3 US Steel preheated coal batteries and is now being used at Nippon Steel's Muroran works. The process is important to the re-use of the water for quenching and is a vital first step in making the liquor harmless to the environment. It is particularly useful in plants using preheated coal where there is likely to be carry over of fine coal particles.

  20. Granulation for Coking Wastewater Treatment in a Coupled Anaerobic-Aerobic Reactor

    Science.gov (United States)

    Dong, Chunjuan; Lv, Bingnan

    2018-06-01

    A coupled anaerobic-aerobic granular bio-film reactor was employed with two operation stages: Stage I, granular sludge was formed from digestion sludge using brewery wastewater, and Stage II, granular sludge was acclimatized using coking wastewater. Two oxygenation methods (i.e. A and B) were employed to acclimatize the granules. For method A, dissolved O 2 was supplied through a continuous oxygenation way of 800-15000ml-min-1 . And for method B, dissolved O2 was supplied of 800-15000ml-min-1 18-12 times at 20-60min intervals, 1h each time. The experimental results showed that granules could quickly form in 10d in the EGSB reactor seeded with digestion sludge and little loose granules lack of nutrition, and it was the key factor for granules forming to add little loose granules. It took only about 6 months for granules acclimation using coking wastewater. Both oxygenation methods could run well when acclimatizing the granules. However, method A could have comparatively high and stable operation effect. The actual coking wastewater had distinct inhibition effect on the granules, but the supplement of some oxygen could promote the recovery of SMA, and NaHCO3 supplement could also weaken the inhibition effect of the CWW. Method A had more strongly activity recovery ability than method B.

  1. Effects of mechanical activation on the carbothermal reduction of chromite with metallurgical coke

    Directory of Open Access Journals (Sweden)

    Kenan Yıldız

    2010-06-01

    Full Text Available The carbothermal reduction of mechanically activated chromite with metallurgical coke under an argon atmosphere was investigated at temperatures between 1100 and 1400°C and the effects of the mechanical activation on chromite structure were analyzed by x-ray diffraction (XRD and scanning electron microscopy (SEM. An increase in specific surface area resulted in more contact points. The activation procedure led to amorphization and structural disordering in chromite and accelerated the degree of reduction and metalization in the mixture of chromite and metallurgical coke. Carbothermal reduction products were analzed by using scanning electron microscopy (SEM/EDS.

  2. Fast-neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

    International Nuclear Information System (INIS)

    Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

    1988-01-01

    A fast neutron and γ-ray transmission technique is being developed for the on-line analysis of moisture. Calculations show that the technique is capable of determining coke moisture to better than 0.2 wt% over a wide range of coke thicknesses. The favoured technique uses a thick Li-glass detector surrounded by a neutron moderator to determine simultaneously the fast neutron and γ-ray intensities. Laboratory measurements on single coke samples showed that moisture can be determined to within 0.2 wt% over the range 3-13 wt% moisture and 300-500 mm thickness. Measurements on a range of coke samples showed that the increase in r.m.s. error due to bound H variations is less than about 0.4 wt% moisture. Applications of the technique, to moisture determination in black and brown coal are also investigated, both by calculation and experiment. Further potential applications of the technique are discussed, including the determination of C in steel. (author)

  3. Analysis of coke precursor on catalyst and study on regeneration of catalyst in upgrading of bio-oil

    International Nuclear Information System (INIS)

    Guo, Xiaoya; Zheng, Yong; Zhang, Baohua; Chen, Jinyang

    2009-01-01

    Catalyst HZSM-5 was used in bio-oil catalytic cracking upgrading. The precursor of coke on the catalyst was analyzed by means of TGA, FTIR and C13 NMR. Precursors of coke deposited in the pore of the molecular sieve were mainly aromatic hydrocarbon with the boiling point range from 350 o C to 650 o C. Those on the outer surface of the pellet precursor were identified as saturated aliphatic hydrocarbons with the boiling point below 200 o C. The activity of HZSM-5 was studied after regeneration. In terms of yield of organic distillate and formation rate of coke, results showed that catalytic activity change moderately during the first three times of regeneration.

  4. modelling and modelling and simulation of coking in the riser

    African Journals Online (AJOL)

    eobe

    into the modeling of FCC riser by predicting catalyst coke content as a function of reaction by predicting ... understanding of the process, hence restricting scale up to within the ... MATLAB (R2009a) on a Compaq HP CQ61 laptop. The following ...

  5. Conceptual design of coke-oven gas assisted coal to olefins process for high energy efficiency and low CO2 emission

    International Nuclear Information System (INIS)

    Man, Yi; Yang, Siyu; Zhang, Jun; Qian, Yu

    2014-01-01

    Highlights: • A novel coke-oven gas assisted coal to olefins (GaCTO) process is proposed. • GaCTO has higher energy efficiency and emits less CO 2 compared to coal-to-olefins process. • GaCTO proposes an idea of using redundant coke-oven gas for producing value added products. - Abstract: Olefins are one of the most important platform chemicals. Developing coal-to-olefins (CTO) processes is regarded as one of promising alternatives to oil-to-olefins process. However, CTO suffers from high CO 2 emission due to the high carbon contents of coal. In China, there is 7 × 10 10 m 3 coke-oven gas (COG) produced in coke plants annually. However, most of the hydrogen-rich COG is utilized as fuel or discharged directly into the air. Such situation is a waste of precious hydrogen resource and serious economic loss, which causes serious environmental pollution either. This paper proposes a novel co-feed process of COG assist CTO in which CH 4 of COG reacts with CO 2 in a Dry Methane Reforming unit to reduce emissions, while the Steam Methane Reforming unit produces H 2 -rich syngas. H 2 of COG can adjust the H/C ratio of syngas. The analysis shows that the energy efficiency of the co-feed process increases about 10%, while at the same time, life cycle carbon footprint is reduced by around 85% in comparison to the conventional CTO process. The economic sustainability of the co-feed process will be reached when the carbon tax would be higher than 150 CNY/t CO 2

  6. Heat input control in coke ovens battery using artificial intelligence

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, R.; Kannan, C.; Sistla, S.; Kumar, D. [Tata Steel, Jamshedpur (India)

    2005-07-01

    Controlled heating is very essential for producing coke with certain desired properties. Controlled heating involves controlling the heat input into the battery dynamically depending on the various process parameters like current battery temperature, the set point of battery temperature, moisture in coal, ambient temperature, coal fineness, cake breakage etc. An artificial intelligence (AI) based heat input control has been developed in which currently some of the above mentioned process parameters are considered and used for calculating the pause time which is applied between reversal during the heating process. The AI based model currently considers 3 input variables, temperature deviation history, current deviation of the battery temperature from the target temperature and the actual heat input into the battery. Work is in progress to control the standard deviation of coke end temperature using this model. The new system which has been developed in-house has replaced Hoogovens supplied model. 7 figs.

  7. Coking- and sintering-resistant palladium catalysts achieved through atomic layer deposition.

    Science.gov (United States)

    Lu, Junling; Fu, Baosong; Kung, Mayfair C; Xiao, Guomin; Elam, Jeffrey W; Kung, Harold H; Stair, Peter C

    2012-03-09

    We showed that alumina (Al(2)O(3)) overcoating of supported metal nanoparticles (NPs) effectively reduced deactivation by coking and sintering in high-temperature applications of heterogeneous catalysts. We overcoated palladium NPs with 45 layers of alumina through an atomic layer deposition (ALD) process that alternated exposures of the catalysts to trimethylaluminum and water at 200°C. When these catalysts were used for 1 hour in oxidative dehydrogenation of ethane to ethylene at 650°C, they were found by thermogravimetric analysis to contain less than 6% of the coke formed on the uncoated catalysts. Scanning transmission electron microscopy showed no visible morphology changes after reaction at 675°C for 28 hours. The yield of ethylene was improved on all ALD Al(2)O(3) overcoated Pd catalysts.

  8. Assessment of PAH-exposure among coke oven workers

    Energy Technology Data Exchange (ETDEWEB)

    Vahakangas, K. [and others] [Oulu University, Oulu (Finland)

    1992-12-31

    Levels of BaP diol epoxide - DNA adducts in urine and blood were monitored for workers at the Raahe coking plant, Finland, and other relevant information was collected. All adduct values were low, but oven battery workers had slightly higher values than matched controls. Antibodies to these adducts increased somewhat after work at the plant started, no differences between smokers and non-smokers were found.

  9. Preparation of briquettes on the basis of desintegrated phyto-materials and the admixture of fine-grained coal and coke

    Directory of Open Access Journals (Sweden)

    Jakabský Štefan

    2002-03-01

    Full Text Available The contribution deals with the preparation of small-diameter briquettes on the basis of desintegrated phyto-materials and the admixture of coal and coke. The phyto-materials are classified as a dry biomass that can be, on the one hand, the wastes from wood-working industry,(sawdust, chips, bark, etc. or dried mass from the plant production and, on the other hand, the mass of quick-growing plants cultivated on special plantations. In present time this renewable energy resource attracts attention by its heating value ranging from 10 to 16 MJ.kg-1 (EkoWATT, 2001, a low ash content of 0.5 – 6.5 % and by a low sulphur content in a water free sample of 0.05 –0.12 %.As a phyto-material the spruce sawdusts having a grain size of –2 mm were used. The admixture of brown coal, hard coal and coke with a grain size of 0.040 mm was added to the sawdust and in such way prepared mixtures were subjected to briquetting with the aim to obtain small-diameter briquettes. The influence of admixtures amount on the density, and the suitable briquetting press have been studied. A saleability of briquettes on the basis of phyto-materials is conditioned by their density that must be higher than 1,000 kg.m-3. Thus, an adding of denser material with a relatively high calorific value would enable to attain the required density as well as to retain and/or to improve the main utility properties, i.e. calorific value and ash content.The adding evinces itself in an enhancement of briquetting press, but also density of obtained briquettes is often much higher that required by the market. It was showed that in the case of clear spruce sawdust the density of 1,059 kg.m-3 under the briquetting press of 250 MPa can be attained. According to other results, an admixture of brown coal is not very favourable because briquetting press exceeds the value of 300 MPa. As to hard coal adding, the presses under 250 MPa were achieved at the content of 25 – 30 %. The density of these

  10. Pulsed corona discharge for improving treatability of coking wastewater.

    Science.gov (United States)

    Liu, Ming; Preis, Sergei; Kornev, Iakov; Hu, Yun; Wei, Chao-Hai

    2018-02-01

    Coking wastewater (CW) contains toxic and macromolecular substances that inhibit biological treatment. The refractory compounds remaining in biologically treated coking wastewater (BTCW) provide chemical oxygen demand (COD) and color levels that make it unacceptable for reuse or disposal. Gas-phase pulsed corona discharge (PCD) utilizing mostly hydroxyl radicals and ozone as oxidants was applied to both raw coking wastewater (RCW) and BTCW wastewater as a supplemental treatment. The energy efficiency of COD, phenol, thiocyanate and cyanide degradation by PCD was the subject of the research. The cost-effective removal of intermediate oxidation products with addition of lime was also studied. The energy efficiency of oxidation was inversely proportional to the pulse repetition frequency: lower frequency allows more effective utilization of ozone at longer treatment times. Oxidative treatment of RCW showed the removal of phenol and thiocyanate at 800 pulses per second from 611 to 227mg/L and from 348 to 86mg/L, respectively, at 42kWh/m 3 delivered energy, with substantial improvement in the BOD 5 /COD ratio (from 0.14 to 0.43). The COD and color of BTCW were removed by 30% and 93%, respectively, at 20kWh/m 3 , showing energy efficiency for the PCD treatment exceeding that of conventional ozonation by a factor of 3-4. Application of lime appeared to be an effective supplement to the PCD treatment of RCW, degrading COD by about 28% at an energy input of 28kWh/m 3 and the lime dose of 3.0kg/m 3 . The improvement of RCW treatability is attributed to the degradation of toxic substances and fragmentation of macromolecular compounds. Copyright © 2017. Published by Elsevier B.V.

  11. Structural transformations in thermal treatment of carbon material based on Slantsy coke

    Energy Technology Data Exchange (ETDEWEB)

    Tyumentsev, V.A.; Semenov, P.V.; Podkopaev, S.A.; Noneshneva, N.P.; Golovin, A.V. [Chelyabinsk State University, Chelyabinsk (Russian Federation)

    2000-07-01

    Structural transformations occurring in a carbon material based on high-sulfur Slantsy coke during isothermal treatment (1200-2400{degree}C) under normal pressure in a nitrogen atmosphere were studied.

  12. A Feasibility Study of Ammonia Recovery from Coking Wastewater by Coupled Operation of a Membrane Contactor and Membrane Distillation

    Directory of Open Access Journals (Sweden)

    Po-Hsun Lin

    2018-03-01

    Full Text Available More than 80% of ammonia (NH3 in the steel manufacturing process wastewater is contributed from the coking wastewater, which is usually treated by biological processes. However, the NH3 in the coking wastewater is typically too high for biological treatment due to its inhibitory concentration. Therefore, a two-stage process including a hollow fiber membrane contactor (HFMC and a modified membrane distillation (MD system was developed and applied to reduce and recover NH3 from coking wastewater. The objectives of this paper are to evaluate different membrane materials, receiving solutions, and operation parameters for the system, remove NH3 from the coking wastewater to less than 300 mg N/L, which is amenable to the biological process, and recover ammonia solution for reuse. As a result, the polytetrafluoroethylene (PTFE HFMC using sulfuric acid as a receiving solution can achieve a maximum NH3-N transmembrane flux of 1.67 g N/m2·h at pH of 11.5 and reduce NH3 in the coking wastewater to less than 300 mg N/L. The NH3 in the converted ammonium sulfate ((NH42SO4 was then recovered by the modified MD using ice water as the receiving solution to produce ≥3% of ammonia solution for reuse.

  13. Effect of hydrothermal treatment of coal on the oxidation susceptibility and electrical resistivity of HTT coke

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, N.B.; Sarkar, P.; Choudhury, A. [Central Fuel Research Institute, P.O. FRI, Dhanbad-828108, Jharkhand (India)

    2005-02-25

    The influence of hydrothermal treatment of coal prior to carbonization, on the oxidation susceptibility of resultant coke/char, calcined at 1350, 1800 and 2200 {sup o}C has been investigated. The non-isothermal thermogravimetric analysis technique has been employed, and parameters such as onset, DTG peak temperatures, and cumulative oxidation loss (wt.%) at different temperatures have been utilized to compare proneness to oxidation with respective untreated samples apart from electrical resistivity. Data suggest that all the cokes/chars samples produced from hydrothermally treated coals are less reactive and more electrically conductive (less resistive) than their respective untreated counterparts. But the extent of improvement of oxidation resistance and electrical conductivity appears to be coal-specific. The kinetic parameters obtained by non-linear regression analysis on multi-curve reveal that the n{sup th} order reaction model (where 'n' was found to vary from 0.9 to 1.3) is the best-fitted model. The higher activation energy values observed for hydrothermally treated coke samples are in agreement with the observation of TG analysis data. Overall results indicate the importance of introducing a hydrothermal treatment step for the improvement of oxidation resistance as well as electrical conductivity of the coke samples.

  14. Influence of thermoplastic properties on coking pressure generation: Part 1 - A study of single coals of various rank

    Energy Technology Data Exchange (ETDEWEB)

    John J. Duffy; Merrick R. Mahoney; Karen M. Steel [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre

    2010-07-15

    In this study a number of high coking pressure coals with different fluidities were evaluated alongside a number of low pressure coals also with differing fluidities. This was to establish rheological parameters within which a coal may be considered potentially dangerous with regards to coking pressure. The results have confirmed and elaborated on previous findings which show that parallel plate displacement ({Delta}L) and axial force profiles can be used to distinguish between high and low pressure coals, with peak values indicating cell rupture and subsequent pore network formation. This is thought to correspond with plastic layer compaction in the coke oven. For low pressure coals pore coalescence occurs quite early in the softening process when viscosity/elasticity are decreasing and consequently a large degree of contraction/collapse is observed. For higher pressure coals the process is delayed since pore development and consequently wall thinning progress at a slower rate. If or when a pore network is established, a lower degree of contraction/collapse is observed because the event occurs closer to resolidification, where viscosity and elasticity are increasing. For the higher fluidity, high coking pressure coals, a greater degree of swelling is observed prior to cell rupture, and this is considered to be the primary reason for the high coking pressure observed with these coals. An additional consequence of these events is that high pressure coals are likely to contain a higher proportion of closed cells both at and during resolidification, reducing permeability in both the semi-coke and high temperature plastic layers, respectively. Using a rheological mapping approach to follow viscoelastic changes during carbonisation it has been possible to identify specific regions associated with dangerous coals. 76 refs., 11 figs., 3 tabs.

  15. Effluents of toxic and corrosion-active components at coke-oven gas combustion

    International Nuclear Information System (INIS)

    Mikhajlov, G.S.; Afanas'ev, Yu.O.; Plotnikov, V.A.; Iskhakov, Kh.A.; Tikhov, S.D.; Gaus, A.I.; Nagibin, P.D.

    1996-01-01

    Various modes of coke-coal gas combustion are studied and dependence of concentration of nitrogen sulfur oxides and carbon monoxides originating in smoke gases on the air excess delivered to the combustion chamber is determined. The lowest summary releases of hazardous substances are achieved by the excess air coefficients α > 1.2 relative to modes of coke-coal gas combustion with smoke gases recirculation. The quantity of sulfur does not depend on the mode of fuel combustion and is determined by the total sulfur content in the fuel. To prevent the corrosion of low-temperature heat exchange surfaces it is necessary to heat up the feed-water up to the temperature exceeding the temperature of the coal gases dew point by 10-15 deg C. 10 refs

  16. 40 CFR 60.105a - Monitoring of emissions and operations for fluid catalytic cracking units (FCCU) and fluid coking...

    Science.gov (United States)

    2010-07-01

    ..., Catalytic Reforming Units, and Sulfur Recovery Units. (iii) The owner or operator shall install, operate... for fluid catalytic cracking units (FCCU) and fluid coking units (FCU). 60.105a Section 60.105a... and operations for fluid catalytic cracking units (FCCU) and fluid coking units (FCU). (a) FCCU and...

  17. The US merchant blast furnace coke market: current state of play

    Energy Technology Data Exchange (ETDEWEB)

    Aloe, A. [Shenango Inc., Pittsburgh, PA (US)

    2004-07-01

    A five page text is accompanied by a set of 11 slides/overheads. The talk discussed the reasons why the presenter believes that coke prices will stay above their historical levels for the foreseeable future. 3 refs., 1 fig., 2 tabs.

  18. Characterisation of the coke formed during metal dusting of iron in CO-H2-H2O gas mixtures

    International Nuclear Information System (INIS)

    Zhang, J.; Schneider, A.; Inden, G.

    2003-01-01

    Carbon deposits formed on the surface of iron samples during carburisation at 700 deg. C in a gas mixture of 75%CO-24.81%H 2 -0.19%H 2 O were characterised by using scanning electron microscopy (SEM), X-ray diffraction (XRD), Moessbauer spectroscopy and transmission electron microscopy (TEM). Cross-section observation of the iron sample by light optical microscopy revealed the formation of cementite after only 10 min reaction, together with a thin layer of graphite. After 4 h reaction, a thick coke layer was formed on top of the cementite surface. SEM surface observation indicated the formation of filamentous carbon in the coke layer. Further analysis of the coke by XRD and Moessbauer showed the presence of mainly Fe 3 C and small amount of Fe 2 C but no metallic iron in the carbon deposit. TEM analysis of the coke detected very convoluted filaments with iron-containing particles at the tip or along their length. These particles were identified to be cementite by selected area diffraction. Carbon deposits produced at the same temperature but with other gas compositions were also analysed by using XRD. It was found that with a low content of CO, e.g. 5%, both α-Fe and Fe 3 C were detected in the coke. Increasing CO content to more than 30%, iron carbide was the only iron-containing phase

  19. Formation of nitrogen-containing compounds during slow pyrolysis and oxidation of petroleum coke

    Energy Technology Data Exchange (ETDEWEB)

    Furimsky, E.; Ohtsuka, Y. [IMAF Group, Ottawa, ON (Canada)

    1997-09-01

    The petroleum coke from a fluid coking process was pyrolyzed in helium and oxidized in 1% and 4% O{sub 2} and in air, with the aim to determine N-containing compounds such as HCN, NH{sub 3}, NO, and N{sub 2}O. The experiments were performed with and without limestone. NO was the major product during all oxidation runs. N{sub 2}O was formed only in air. In this case, N{sub 2}O formation was delayed when compared with that of NO. The addition of limestone decreased formation of HCN and increased that of NH{sub 3}, whereas NO formation was least affected. 36 refs., 8 figs., 6 tabs.

  20. Oxygen-containing coke species in zeolite-catalyzed conversion of methanol to hydrocarbons

    KAUST Repository

    Liu, Zhaohui; Dong, Xinglong; Liu, Xin; Han, Yu

    2016-01-01

    Zeolites are the most commonly used catalysts for methanol-to-hydrocarbon (MTH) conversion. Here, we identified two oxygen-containing compounds as coke species in zeolite catalysts after MTH reactions. We investigated the possible influences

  1. Effect of the exposure time in coke making atmosphere on the microstructure and properties of a refractory castable used in the petrochemical industry

    International Nuclear Information System (INIS)

    Cabrelon, M.D.; Pereira, A.H.A.; Rodrigues, J.A.; Medeiros, J.; Toledo-Filho, R.D.

    2012-01-01

    Refractory castables used in Fluidized Catalytic Cracking Units (FCCU) are said to deteriorate due coke formation during the production of light hydrocarbons, causing a shortening in the operating time of the reactor. Consequently, a significant financial loss for the petrochemical will occur. Several studies have been carried out, but none of them showed clearly how much is the contribution of the coke for the concrete final deterioration. It still remains the doubt if the coke is the responsible for the damage observed macroscopically in a FCCU's riser. In this way, this work aimed to study the effect of the time in a coke making atmosphere on an anti-erosive class-C refractory castable, seeking for microstructural changes or on physical properties that indicate degradation mechanisms and give support to the understanding of the phenomenon. Samples of an industrial refractory castable used in petrochemical units were prepared and subjected to a forced coke making process in a simulation reactor. The temperature and the heating rate were kept constant at 540 deg C and 50 deg C/h, respectively. The values of 10, 60, 120, 240 and 480 h were used for the time of exposition to the propene gas. The microstructure of the samples was characterized through optical and scanning electron microscopy and its mineralogical phases through X-ray diffraction. Complementary analyses were necessary to a better understanding of the phenomenon. The results show that the surface and the microstructure are gradually impregnated by coke, which fills up pores, microcracks and cracks. Evidences of microcracking around the coke filled pores were not found. However, many aggregates present some type of deterioration related to the time of exposition to propene. Those damages are not necessarily caused by coke directly (author)

  2. Delayed coking unit preheat train optimization; Otimizacao do preaquecimento das Unidades de Coque

    Energy Technology Data Exchange (ETDEWEB)

    Marins, Edson R; Geraldelli, Washington O; Barros, Francisco C [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2004-07-01

    The oil industry has been investing in research and development of new techniques and process improvements with the objective to increase the residual fraction profitability and to fulfill the market demands. The adequacy of the refining scheme has led to the development of bottom of the barrel processes that has the objective to convert heavy fractions into products of higher aggregate value. In this context, the process of Delayed Coking presents a great importance in the production of distillates in the diesel range as well as the processing of heavy residues, mostly in the markets where the fuel oil consumption is being reduced. With the approach to help PETROBRAS decide which route to follow during new designs of Delayed Coking units, this work presents a comparative study of the preheat train performance among the energy recovery to preheat the feed, in contrast with preheating the feed and generating steam, simultaneously. In this study the Pinch Technology methodology was used as a procedure for heat integration with the objective of getting the maximum energy recovery from the process, finding the best trade-off between operational cost and investment cost. The alternative of steam generation aims to provide an appropriate flexibility in Delayed Coking units design and operation. (author)

  3. Coking coal of Checua Lenguazaque area; Carbones coquizantes del area Checua - Samaca

    Energy Technology Data Exchange (ETDEWEB)

    Arboleda Otalora, Carlos Ariel

    1987-06-01

    In this report a summary of the main characteristics of the coal of the area of Checua-Samaca is presented. Using the main works carried out on this area, the most important geologic, physical-chemical, technological and petrographic aspects are compiled that are considered essential to carry out a technical evaluation of these coal and all the analyses they take to conclude that in this area, bituminous coal are presented with very good coking properties, on the other hand, it is demonstrated by the use that is given to the coal extracted by the small existent mining. However, keeping in mind the demands of the international market of the coking coal, it becomes necessary to improve the existent geologic information to be able to make reliable stratigraphic correlations.

  4. Emission of Polychlorinated Dibenzo-p-Dioxins (PCDDs and Polychlorinated Dibenzofurans (PCDFs from Underfiring System of Coke Oven Battery

    Directory of Open Access Journals (Sweden)

    Rafał Bigda

    2017-11-01

    Full Text Available A coke oven battery is not considered as a significant source of PCDDs/PCDFs emissions; however, due to small amounts of chlorine in coal dioxins, dibenzofurans may be formed. The paper presents the attempts to determine the level of emission of PCDDs/PCDFs from the COB underfiring system and to confront the obtained results with the calculations based on the mass balance of chlorine in the coking process and reactions of both chlorophenols formation and PCDDs and PCDFs formation from mono- and polychlorophenols. There were PCDDs/PCDFs concentrations measured in flue gases from the underfiring system of two COBs at a Polish coking plant. The measurements included both an old and a new battery. The obtained concentrations of PCDDs/PCDFs were lower than reported in the literature (0.5-1.7 ng I-TEQ/tcoke, while the results for old COB were on average 3 times higher than for the new one. It was found that PCDD/F emission from COB underfiring system is insignificant and that PCDDs/PCDFs formation during coal coking should consider the mechanisms of their formation from mono- and polychlorophenols, as well as the influence of process parameters on the synthesis.

  5. Investigation on the fates of vanadium and nickel during co-gasification of petroleum coke with biomass.

    Science.gov (United States)

    Li, Jiazhou; Wang, Xiaoyu; Wang, Bing; Zhao, Jiantao; Fang, Yitian

    2018-06-01

    This study investigates the volatilization behaviors and mineral transformation of vanadium and nickel during co-gasification of petroleum coke with biomass. Moreover, the evolution of occurrence modes of vanadium and nickel was also determined by the method of sequential chemical extraction. The results show that the volatilities of vanadium and nickel in petroleum coke have a certain level of growth with an increase in the temperature. With the addition of biomass, their volatilities both show an obvious decrease. Organic matter and stable forms are the dominant chemical forms of vanadium and nickel. After gasification, organic-bound vanadium and nickel decompose completely and convert into other chemical forms. The crystalline phases of vanadium trioxide, coulsonite, nickel sulfide, and elemental nickel are clearly present in petroleum coke and biomass gasification ashes. When the addition of biomass reaches 60 wt%, the diffraction peaks of orthovanadate are found while that of vanadium trioxide disappear. Copyright © 2018 Elsevier Ltd. All rights reserved.

  6. The aquatic toxicity and chemical forms of coke plant effluent cyanide -- Implications for discharge limits

    International Nuclear Information System (INIS)

    Garibay, R.; Rupnow, M.; Godwin-Saad, E.; Hall, S.

    1995-01-01

    Cyanide is present in treated cokemaking process waters at concentrations as high as 8.0 mg/L. In assessing options for managing the discharge of a treated effluent, the development and implementation of discharge limits for cyanide became a critical issue. A study was initiated to evaluate possible alternatives to cyanide permit limits at the US Steel Gary Works Facility. The objectives of the study were to: (1) evaluation the forms of cyanide present in coke plant effluent; (2) determine whether these forms of cyanide are toxic to selected aquatic organisms; (3) compare the aquatic toxicity of various chemical forms of cyanide; (4) identify if the receiving water modifies cyanide bioavailability; and (5) confirm, with respect to water quality-based effluent limits, an appropriate analytical method for monitoring cyanide in a coke plant effluent. The results of aquatic toxicity tests and corresponding analytical data are presented. Toxicity tests were conducted with various pure chemical forms of cyanide as well as whole coke plant effluent (generated from a pilot-scale treatment system). Test species included the fathead minnow (Pimephales promelas), rainbow trout (Oncorhynchus mykiss), Ceriodaphnia dubia (C. dubia) and Daphnia magna (D. magna). Analytical measurements for cyanide included total, weak acid dissociable, diffusible cyanide and selected metal species of cyanide. The findings presented by the paper are relevant with respect to the application of cyanide water quality criteria for a coke plant effluent discharge, the translation of these water quality-based effluent limits to permit limits, and methods for compliance monitoring for cyanide

  7. Ash fusion characteristics during co-gasification of biomass and petroleum coke.

    Science.gov (United States)

    Xiong, Qing-An; Li, Jiazhou; Guo, Shuai; Li, Guang; Zhao, Jiantao; Fang, Yitian

    2018-06-01

    In this study, the effect of biomass ash on petroleum coke ash fusibility was investigated at a reducing atmosphere. Some analytical methods, such as ash fusion temperatures (AFTs) analysis, X-ray diffraction (XRD), FactSage and scanning electron microscopy (SEM), were applied to determine the characteristics of ash fusion and transformation of mineral matters. The results indicated that AFTs were closely associated with ash mineral compositions. It was found that the formations of high melting point calcium silicate, vanadium trioxide and coulsonite resulted in the high AFTs of Yanqing petroleum coke (YQ). When blending with certain proportional pine sawdust (PS), corn stalk (CS), the AFTs of mixture could be decreased significantly. For PS addition, the formations of low-melting point calcium vanadium oxide should be responsible for the reduction of AFTs, whereas for CS addition the reason was ascribed to the formation of low-melting point leucite and the disappearance of high-melting V 2 O 3 . Copyright © 2018. Published by Elsevier Ltd.

  8. Continuous moisture measurement in metallurgical coke with automatic charge correction

    International Nuclear Information System (INIS)

    Watzke, H.; Mehlhose, D.

    1981-01-01

    A process control system has been developed for automatic batching of the coke amount necessary for metallurgical processes taking into account the moisture content. The measurement is performed with a neutron moisture gage consisting of an Am-Be neutron source and a BF 3 counter. The output information of the counter is used for computer-controlled batching

  9. Microsoft PowerPoint - Walter Coke Comm May 19 Karen correction presentation [Compatibility Mode

    Science.gov (United States)

    Contains slides from a presentation to Collegeville, Harriman Park, and Fairmont neighborhoods in North Birmingham, Alabama updating the community on the environmental sampling and next steps on the Walter Coke cleanup site.

  10. Dripping and evolution behavior of primary slag bearing TiO2 through the coke packed bed in a blast-furnace hearth

    Science.gov (United States)

    Liu, Yan-xiang; Zhang, Jian-liang; Wang, Zhi-yu; Jiao, Ke-xin; Zhang, Guo-hua; Chou, Kuo-chih

    2017-02-01

    To investigate the flow of primary slag bearing TiO2 in the cohesive zone of blast furnaces, experiments were carried out based on the laboratory-scale packed bed systems. It is concluded that the initial temperature of slag dripping increases with decreasing FeO content and increasing TiO2 content. The slag holdup decreases when the FeO content is in the range of 5wt%-10wt%, whereas it increases when the FeO content exceeds 10wt%. Meanwhile, the slag holdup decreases when the TiO2 content increases from 5wt% to 10wt% but increases when the TiO2 content exceeds 10wt%. Moreover, slag/coke interface analysis shows that the reaction between FeO and TiO2 occurs between the slag and the coke. The slag/coke interface is divided into three layers: slag layer, iron-rich layer, and coke layer. TiO2 in the slag is reduced by carbon, and the generated Ti diffuses into iron.

  11. Catalytic wet air oxidation of coke-plant wastewater on ruthenium-based eggshell catalysts in a bubbling bed reactor.

    Science.gov (United States)

    Yang, M; Sun, Y; Xu, A H; Lu, X Y; Du, H Z; Sun, C L; Li, C

    2007-07-01

    Catalytic wet air of coke-plant wastewater was studied in a bubbling bed reactor. Two types of supported Ru-based catalysts, eggshell and uniform catalysts, were employed. Compared with the results in the wet air oxidation of coke-plant wastewater, supported Ru uniform catalysts showed high activity for chemical oxygen demand (COD) and ammonia/ammonium compounds (NH3-N) removal at temperature of 250 degrees C and pressure of 4.8 MPa, and it has been demonstrated that the catalytic activity of uniform catalyst depended strongly on the distribution of active sites of Ru on catalyst. Compared to the corresponding uniform catalysts with the same Ru loading (0.25 wt.% and 0.1 wt.%, respectively), the eggshell catalysts showed higher activities for CODcr removal and much higher activities for NH3-N degradation. The high activity of eggshell catalyst for treatment of coke-plant wastewater can be attributed to the higher density of active Ru sites in the shell layer than that of the corresponding uniform catalyst with the same Ru loading. It has been also evidenced that the active Ru sites in the internal core of uniform catalyst have very little or no contribution to CODcr and NH3-N removal in the total oxidation of coke-plant wastewater.

  12. Health-hazard evaluation report No. HETA-88-377-2120, Armco Coke Oven, Ashland Kentucky

    International Nuclear Information System (INIS)

    Kinnes, G.M.; Fleeger, A.K.; Baron, S.L.

    1991-06-01

    In response to a request from the Oil, Chemical and Atomic Workers International Union, a study was made of possible hazardous working conditions at ARMCO Coke Oven (SIC-3312), Ashland, Kentucky. The facility produces about 1,000,000 tons of coke annually. Of the approximately 400 total employees at the coke oven site, 55 work in the by products area. Air quality sampling results indicated overexposure to both benzene (71432) and coal tar pitch volatiles (CTPVs). Airborne levels of benzene ranged as high as 117 parts per million (ppm) with three of 17 samples being above the OSHA limit of 1ppm. Airborne concentrations of CTPVs ranged as high as 0.38mg/cu m with two of six readings being above OSHA limit of 0.2mg/cu m. Several polynuclear aromatic hydrocarbons were also detected. The authors conclude that by products area workers are potentially overexposed to carcinogens, including benzene, CTPVs, and polynuclear aromatic hydrocarbons. An epidemiologic study is considered unlikely to yield meaningful information at this time, due to the small number of workers and the short follow up period. The authors recommend specific measures for reducing potential employee exposures, including an environmental sampling program, a preventive maintenance program, improved housekeeping procedures, and reducing exposure in operators' booths

  13. Nitrogen conversion during rapid pyrolysis of coal and petroleum coke in a high-frequency furnace

    International Nuclear Information System (INIS)

    Yuan, Shuai; Zhou, Zhi-jie; Li, Jun; Wang, Fu-chen

    2012-01-01

    Highlights: ► Use a high-frequency furnace to study N-conversion during rapid pyrolysis of coal. ► Scarcely reported N-conversion during rapid pyrolysis of petroleum coke was studied. ► Both of NH 3 and HCN can be formed directly from coal during rapid pyrolysis. ► NH 3 –N yields are higher than HCN–N yields in most conditions. ► NH 3 –N yields of petroleum coke increase with temperature and no HCN detected. -- Abstract: Rapid pyrolysis of three typical Chinese coals, lignite from Inner Mongolia, bituminous from Shenfu coalfield, and anthracite from Guizhou, as well as a petroleum coke were carried out in a drop-style high-frequency furnace. The reactor was induction coil heated and had a very small high-temperature zone, which could restrain secondary conversions of nitrogen products. The effects of temperature and coal rank on conversions of fuel-N to primary nitrogen products (char-N, HCN–N, NH 3 –N and (tar + N 2 )–N) have been investigated. The results showed that, the increasing temperature reduced the yields of char-N and promoted the conversion of fuel-N to N 2 . Char-N yields increased, while volatile-N yields decreased as the coal rank increased. In most of the conditions, NH 3 –N yields were higher than HCN–N yields during rapid pyrolysis of coal. In the case of petroleum coke, NH 3 –N yields increased gradually with the increasing temperature, but no HCN was detected. We argue that NH 3 –N can be formed directly through the primary pyrolysis without secondary reactions. Although volatile-N yields of lignite were higher than those of bituminous, yields of (HCN + NH 3 )–N in volatile-N of lignite were lower than those of bituminous. While the (HCN + NH 3 )–N yields of anthracite were the lowest of the three coals. Both of the (HCN + NH 3 )–N yields and (HCN + NH 3 )–N proportions in volatile-N of petroleum coke were lower than the three coals.

  14. Process for converting coal into liquid fuel and metallurgical coke

    Science.gov (United States)

    Wolfe, Richard A.; Im, Chang J.; Wright, Robert E.

    1994-01-01

    A method of recovering coal liquids and producing metallurgical coke utilizes low ash, low sulfur coal as a parent for a coal char formed by pyrolysis with a volatile content of less than 8%. The char is briquetted and heated in an inert gas over a prescribed heat history to yield a high strength briquette with less than 2% volatile content.

  15. Improved coking resistance of direct ethanol solid oxide fuel cells with a Ni-Sx anode

    Science.gov (United States)

    Yan, Ning; Luo, Jing-Li; Chuang, Karl T.

    2014-03-01

    In this study, the coking resistance of anode supported direct ethanol solid oxide fuel cell with a Ni-Sx anode was investigated comparatively with the conventional cell using pure Ni catalyst. The surface catalytic properties of Ni were manipulated via depositing a layer of S atoms. It was confirmed that on the surface of Ni, a combination of S monolayer and elemental S was formed without producing Ni3S2 phase. The developed Ni-Sx cell exhibited a significantly improved coke resistivity in ethanol feed while maintaining an adequately high performance. The S species on Ni enabled the suppression of the coke formation as well as the alleviation of the metal dusting effect of the anode structure. After operating in ethanol fuel for identical period of time at 850 °C, a maximum power density of 400 mW cm-2 was sustained whereas the conventional cell performance decreased to less than 40 mW cm-2 from the original 704 mW cm-2. In an optimized stability test, the Ni-Sx cell operated at 750 °C for more than 22 h until the fuel drained without any degradation.

  16. Composition and method for coke retardant during hydrocarbon processing

    International Nuclear Information System (INIS)

    Reid, D.K.

    1988-01-01

    A process is described for inhibiting the formation and deposition of filamentous coke on metallic surfaces in contact with a hydrocarbon having a temperature of 600 0 -1300 0 F which comprises adding to the hydrocarbon a sufficient amount for the purpose of a boron compound selected from the group of boron oxide compounds, boric acid and metal borides, with the proviso that when boric acid is used, it is substantially free of water

  17. Reducibility study of Rossetta ilmenite ore briquettes and powder with coke breeze at 800-1100°C

    Directory of Open Access Journals (Sweden)

    Abd el Gawad Hala H.

    2013-01-01

    Full Text Available Ilmenite ore fine and coke breeze as reduced material were briquetted with different amounts of organic materials such as molasses or pitch were studied in this investigation. The produced briquettes at reasonable condition were reduced in nitrogen atmosphere at temperature range 800 - 1100oC to determine the factors controlling the reduction and to determine the controlling mechanism. Also ilmenite ore fine with coke breeze were reduced at the same temperature range in nitrogen atmosphere without briquetting process, for the sake of comparison.

  18. Coke fouling process on the oil refining; Processo de incrustacao por coque no refino do petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Bombardelli, Clovis; Fiorentin, Leila D.; Negrao, Cezar O.R.; Franco, Admilson T. [Centro Federal de Educacao Tecnologica do Parana (CEFET-PR), Curitiba, PR (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica e de Materiais (PPGEM)

    2004-07-01

    The heavy crude fraction processing is performed under very high vacuum to minimize thermal cracking which cause coke deposition and damage the equipment. The current tendency is to process heavier oil leading to higher process temperatures and consequently to greater fouling. This situation demands better knowledge fouling process by carbonization. This problem is pronounced in the residual gasoil region of a vacuum distillation unit because it obstructs the recirculation circuits and the spray system with serious environmental and economics implications. This paper review the main correlated published work related to coke generation and fouling and presents a discussion about the works. (author)

  19. Ecological situation at the coke plant of the Nizhnii Tagil Integrated Iron and Steel Works (according to data from an expert commission of Gosstroi USSR)

    International Nuclear Information System (INIS)

    Filippov, B.S.

    1990-01-01

    A main source of pollution is the Nizhnii Tagil Integrated Iron and Steel Works (NTMK), whose share in the total emissions of harmful substances is very significant. Thus, in 1987 the mean annual dust content in the atmosphere of the city surpassed the maximum admissible concentrations 1.3 times, phenol 2 times, ammonia 2.5 times, benzopyrene 6 times. In 1988 an even higher content of harmful substances was noted. Reconstruction of the coke plant now underway has been called upon to ensure a significant improvement in the ecological conditions together with an overall increase in its technical level. Restoration of the existing capacity of the coke batteries at domestic coke plants is being accomplished according to two variants: first - relining of the batteries with retention of the existing dimensions or with a slight very limited increase, with modernization of the designs of the ovens and chemical departments, and also machines and equipment (technical refitting); second - withdrawal from operation of the existing batteries and construction of new higher capacity coke batteries in the plant area (reconstruction). From the standpoint of ecology and economy of capital investment it would be more expedient to restore capacity at NTMK according to the first variant. However, restoration here is being carried out according to the second variant with construction of coke batteries 9 and 10 in a new area with dry coke quenching. There are plans to decommission batteries 1-4. An analysis is given of the sources of pollution from the coke plant and measures are defined to reduce pollutants

  20. Determination of the coke bed voidage in the blast furnace hearth

    Energy Technology Data Exchange (ETDEWEB)

    Havelange, O.; Danloy, G.; Venturini, M.J. [and others] [CRM, Liege (Belgium)

    2004-07-01

    The objectives of the research were to develop and apply techniques and model tools allowing an online evaluation of the blast furnace hearth conditions and its permeability, in order to guarantee a stable furnace operation and to control the refractory wear through early corrective actions. CRM determined the coke bed voidage in the hearth of BFB of Cockerill-Sambre by two techniques: one based on pressure measurement inside the taphole and the other based on electromotive force measurement. A mathematicalmodel was developed taking into account the movements of the deadman. ln order to continuously determine the hot metal flow rate, BFI measured the filling level in the runner at BF 2 of TKS. A statistical wear model evaluated the cross-sectional runner geometry. The data have been fed into a model to calculate the coke bed voidage on multiple taphole blast furnaces. To control the wear caused by preferential liquid flow, Corus IJmuiden developed a monitoring of temperature and heat flux information from purpose-installed duplex thermocouples. This information has been correlated over time to identify any persistent trends and used to evaluate control measures such as blocked tuyeres and process shutdowns. Industrial trials at Fos BF1 enabled IRSID to propose a picture to describe the effects of the central coke charging practice. IRSID used the Fluent code to describe the liquid flow in the hearth with regard to the deadman conditions and to simulate tracer experiments. From studies of the behaviour of the hearth skull, Corus UK proposed a method for its monitoring. The iron flow rate was measured by using strain gauges attached to the torpedo ladles, and the slag flow rate was estimated from the slag pelletiser current. Data from tuyere core drilling samples were examined to estimate the voidage in the hearth. 38 refs., 127 figs.

  1. Urinary 1-hydroxypyrene concentrations in Chinese coke oven workers relative to job category, respirator usage, and cigarette smoking

    Energy Technology Data Exchange (ETDEWEB)

    Bo Chen; Yunping Hu; Lixing Zheng; Qiangyi Wang; Yuanfen Zhou; Taiyi Jin [Fudan University, Shanghai (China). School of Public Health

    2007-09-15

    1-Hydroxypyrene (1-OHP) is a biomarker of recent exposure to polycyclic aromatic hydrocarbons (PAHs). We investigated whether urinary 1-OHP concentrations in Chinese coke oven workers (COWs) are modulated by job category, respirator usage, and cigarette smoking. The present cross-sectional study measured urinary 1-OHP concentrations in 197 COWs from Coking plant I and 250 COWs from Coking plant II, as well as 220 unexposed referents from Control plant I and 56 referents from Control plant II. Urinary 1-OHP concentrations (geometric mean, {mu}mol/mol creatinine) were 5.18 and 4.21 in workers from Coking plants I and II, respectively. The highest 1-OHP levels in urine were found among topside workers including lidmen, tar chasers, and whistlers. Benchmen had higher 1-OHP levels than other workers at the sideoven. Above 75% of the COWs exceeded the recommended occupational exposure limit of 2.3 {mu}mol/mol creatinine. Respirator usage and increased body mass index (BMI) slightly reduced 1-OHP levels in COWs. Cigarette smoking significantly increased urinary 1-OHP levels in unexposed referents but had no effect in COWs. Chinese COWs, especially topside workers and benchmen, are exposed to high levels of PAHs. Urinary 1-OHP concentrations appear to be modulated by respirator usage and BMI in COWs, as well as by smoking in unexposed referents.

  2. Optimizing anti-coking abilities of zeolites by ethylene diamine tetraacetie acid modification on catalytic fast pyrolysis of corn stalk

    Science.gov (United States)

    Zhang, Bo; Zhong, Zhaoping; Song, Zuwei; Ding, Kuan; Chen, Paul; Ruan, Roger

    2015-12-01

    In order to minimize coke yield during biomass catalytic fast pyrolysis (CFP) process, ethylene diamine tetraacetie acid (EDTA) chemical modification method is carried out to selectively remove the external framework aluminum of HZSM-5 catalyst. X-ray diffraction (XRD), nitrogen (N2)-adsorption and ammonia-temperature programmed desorption (NH3-TPD) techniques are employed to investigate the porosity and acidity characteristics of original and modified HZSM-5 samples. Py-GC/MS and thermo-gravimetric analyzer (TGA) experiments are further conducted to explore the catalytic effect of modified HZSM-5 samples on biomass CFP and to verify the positive effect on coke reduction. Results show that EDTA treatment does not damage the crystal structure of HZSM-5 zeolites, but leads to a slight increase of pore volume and pore size. Meanwhile, the elimination of the strong acid peak indicates the dealumination of outer surface of HZSM-5 zeolites. Treatment time of 2 h (labeled EDTA-2H) is optimal for acid removal and hydrocarbon formation. Among all modified catalysts, EDTA-2H performs the best for deacidification and can obviously increase the yields of positive chemical compositions in pyrolysis products. Besides, EDTA modification can improve the anti-coking properties of HZSM-5 zeolites, and EDTA-2H gives rise to the lowest coke yield.

  3. The integration of cyanide hydratase and tyrosinase catalysts enables effective degradation of cyanide and phenol in coking wastewaters.

    Science.gov (United States)

    Martínková, Ludmila; Chmátal, Martin

    2016-10-01

    The aim of this study was to design an effective method for the bioremediation of coking wastewaters, specifically for the concurrent elimination of their highly toxic components - cyanide and phenols. Almost full degradation of free cyanide (0.32-20 mM; 8.3-520 mg L(-1)) in the model and the real coking wastewaters was achieved by using a recombinant cyanide hydratase in the first step. The removal of cyanide, a strong inhibitor of tyrosinase, enabled an effective degradation of phenols by this enzyme in the second step. Phenol (16.5 mM, 1,552 mg L(-1)) was completely removed from a real coking wastewater within 20 h and cresols (5.0 mM, 540 mg L(-1)) were removed by 66% under the same conditions. The integration of cyanide hydratase and tyrosinase open up new possibilities for the bioremediation of wastewaters with complex pollution. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Comparison of the associative structure of two different types of rich coals and their coking properties

    Energy Technology Data Exchange (ETDEWEB)

    Hengfu Shui; Changhui Lin; Meng Zhang; Zhicai Wang; Mingdong Zheng [Anhui University of Technology, Maanshan (China). School of Chemistry and Chemical Engineering

    2010-07-15

    Solvent extractions of two different types of Chinese rich coals i.e. Aiweiergou coal (AG) and Zaozhuang coal (ZZ) using the mixed solvent of carbon disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) with different mixing ratios were carried out and the caking indexes of the extracted residues were measured. It was found that the extracted residues from the two types of coals showed different changing tendencies of the caking indexes with the extraction yield. When the extraction yield attained about 50% for ZZ coal, the extracted residue had no caking property. However for AG coal, when the extraction yield reached the maximum of 63.5%, the corresponding extracted residue still had considerable caking property with the caking index of 25. This difference indicated the different associative structure of the two coals although they are of the same coalification. Hydro-thermal treatment of the two rich coals gave different extract fractionation distributions for the treated coals compared to those of raw coals respectively. The coking property evaluations of the two coals and their hydro-thermally treated ones were carried out in a crucible coking determination. The results showed that the hydro-thermal treatment could greatly improve the micro-strengths of the resulting coke from the two coals, and the improvement was more significant for the more aggregated AG coal. The reactivities of hydro-thermally treated AG coal blends were almost the same as those of raw coal blends. The higher coke reactivities of AG raw coal and its hydro-thermally treated ones than those of ZZ coal might be attributed to its special ash composition. 20 refs.,4 figs., 5 tabs.

  5. Kress indirect dry cooling system, Bethlehem Steel's Coke Plant demonstration at Sparrows Point, Maryland. Volume 2. Appendices G-N. Final report, February 1990-February 1992

    International Nuclear Information System (INIS)

    Ossman, A.G.

    1993-05-01

    The report provides an evaluation of the Kress Indirect Dry Cooling (KIDC) process. The KIDC process is an innovative system for the handling and cooling of coke produced from a slot type by-product coke oven battery. The report is based on the test work and demonstration of the system at Bethlehem Steel Corporation's Sparrows Point facility in 1991. The report covers both environmental and operational impacts of the KIDC process. The report, Volume 2, contains appendices G-N. Volume 1, PB93-191302, contains the technical report as well as appendices A-F. Volume 2 contains appendixes on coke quality data, blast furnace balwax model report, KIDC operating cost and maintenance requirements, Kress box thickness readings, KIDC coke discharge temperature, QA/QC program, door leak data, and coal data

  6. Microstructural characteristics of toluene and quinoline-insolubles from coal-tar pitch and their cokes

    Energy Technology Data Exchange (ETDEWEB)

    Panaitescu, C. [University POLITEHNICA Bucharest, Faculty of Industrial Chemistry, Fuel Laboratory, Polizu St. 1, Sector 1, 011061, Bucharest (Romania); Predeanu, G. [Metallurgical Research Institute, Department of Raw Materials, Mehadia St. 39, Sector 6, 060543 Bucharest (Romania)

    2007-08-01

    The structural composition of coal-tar pitch used in the preparation of the special binder-pitch, was determined with special emphasis on the optical properties of the {beta}-resins, as typical components necessary to obtain electrodes of best quality through the pyrogenetic processes of baking and graphitization. In addition to raw toluene- and quinoline-insolubles (TI, QI), the corresponding cokes were analysed to evaluate, by structural composition and microtexture, the behaviour of pitch fractions during carbonization. The results suggest the dependence of the texture development on the type of toluene- and quinoline-insolubles and {beta}-resins during processing conditions, which influence the mesophase formation. An original and important result of the carbopetrographical study is represented by the identification and evaluation of {beta}-resins in the coke texture. (author)

  7. Combined biological treatment of sinter plant waste water, blast furnace gas scrubber water polluted groundwater and coke plant effluent

    Energy Technology Data Exchange (ETDEWEB)

    Antoine van Hoorn [Corus Staal, IJmuiden (Netherlands)

    2006-07-01

    Waste water from the Corus coke plant in IJmuiden had been handled by the activated sludge process since start-up in 1972 but in the eighties it was clear that although this removed most phenols, the rest of the COD and thiocyanate must also be removed before discharge. The paper describes the original water treatment process and the higher pressure gas scrubber system for removal of SO{sub 2}, heavy metals and other harmful components. It goes on to describe development of a combined biological treatment system, the heart of which is the so-called Bio 2000. The performance of this new plant is discussed. COD concentrations are very constant but Total Kjeldahl Nitrogen (TKN) concentrations fluctuate. COD, TKN and heavy metals are in compliance but cyanide and suspended solids are not always so. A method of overcoming this is being sought. This paper was presented at a COMA meeting in March 2005 held in Scunthorpe, UK. 10 figs., 2 tabs.

  8. The use of a radioactive tracer for the determination of distillation end point in a coke oven

    International Nuclear Information System (INIS)

    Burgio, N.; Capannesi, G.; Ciavola, C.; Sedda, F.

    1995-01-01

    A novel high precision detection method for the determination of the distillation end point of the coking process (usually in the 950 deg C range) has been developed. The system is based on the use of a metallic capsule that melts at a fixed temperature and releases a radioactive gas tracer ( 133 Xe) in the stream of the distillation gas. A series of tests on a pilot oven confirmed the feasibility of the method on industrial scale. Application of the radioactive tracer method to the staging and monitoring in the coking process appears to be possible. (author). 6 refs., 5 figs., 3 tabs

  9. Refinaria do Nordeste: petroleum coke handling system; Refinaria do Nordeste: desafios do sistema de movimentacao de coque verde de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, Luiz G. de; Cabral, Jose Mauro B. [PETROBRAS S.A., Ipojuca, PE (Brazil). Refinaria do Nordeste (RNEST); Lucredi, Hedewandro A. [PETROBRAS S.A., Paulinia, SP (Brazil). Refinaria de Paulinia (REPLAN); Barros, Francisco Carlos da C. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2008-07-01

    The Delayed Coking Units - DCU - are adequate to the scheme for processing heavy oils where the market of fuel oil or asphalt is low or not profitable. The DCU's are conversion units that produce, in addition to the gas and liquid distilled products, the petcoke. The petcoke, depending on the characteristics, is used in various applications like as in the aluminum, iron, thermoelectric and cement industries. The petcoke is solid and its logistics is quite different from most of the products handled by PETROBRAS; therefore, this product has been a constant challenge in relation to the market requirements. Due to the importance of the DCU at Refinaria do Nordeste, and the petcoke production capacity, the coke handling system was projected in order to ensure the refinery operational continuity. The project permits the expedition and loading of 10,000 tons of petcoke within a period of 12 hours of work for cargo vessel. In the development of the processing project of Refinaria do Nordeste efforts were made to optimize the Delayed Coking Unit for the production of distilled products and the quality of the coke. The DCU operating conditions were projected so as to produce petcoke with quality adequate to the iron and aluminum industry. (author)

  10. Processing of coke oven gas. Primary gas cooling

    Energy Technology Data Exchange (ETDEWEB)

    Ullrich, H [Otto (C.) und Co. G.m.b.H., Bochum (Germany, F.R.)

    1976-11-01

    The primary cooler is an indispensable part of all byproduct processing plants. Its purpose is to cool the raw gas from the coke oven battery and to remove the accompanying water vapor. The greater part of the cooling capacity is utilized for the condensation of water vapor and only a small capacity is needed for the gas cooling. Impurities in the gas, like naphthalene, tar and solid particles, necessitate a special design in view of the inclination to dirt accumulation. Standard types of direct and indirect primary gas coolers are described, with a discussion of their advantages and disadvantages.

  11. Technology for beneficiation of non-coking coals

    Energy Technology Data Exchange (ETDEWEB)

    Bose, S.K.

    1987-04-01

    This article outlines the need for efficient non-coking coal beneficiation plants in India to cope with mass production from opencast coal mines. The existing use of magnetite in heavy medium separation processes is expensive and not very efficient in respect to removing shales from opencast lump coals. Instead a new technique is proposed using a ROMJIG washing plant developed in the Federal Republic of Germany. This provides a very efficient, low cost washing system for the coals and allows the continued integration with the coal blending plants. This simplified technology allows for flexible working hours to meet demand and will allow new developments to continue including fuel slurry pipelines, automated testing of coals and new pulverized boiler fuels.

  12. Interactions among different fractions in the thermoplastic state of Goonyella coking coal

    Energy Technology Data Exchange (ETDEWEB)

    Takahiro Yoshida; Toshimasa Takanohashi; Masashi Iino; Haruo Kumagai; Kenji Kato [National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan)

    2004-04-01

    Goonyella coking-coal was extracted with a 1:1 (v/v) carbon disulfide/N-methyl-2-pyrrolidinone (CS{sub 2}/NMP) mixed solvent and then fractionated into four with pyridine and chloroform. High-temperature {sup 1}H NMR analysis conducted on each fraction and their mixtures in-situ showed that the lightest, the chloroform-soluble fraction (CS), was rich in mobile hydrogen, H{sub m}, the variation of which with temperature corresponded to that of a thermoplastic parameter tan {delta} determined by in-situ viscoelastic measurement. In contrast, chloroform-insoluble and pyridine-soluble (CIPS) and pyridine-insoluble (PIMS) fractions showed scant change in H{sub m} with temperature, although the intermediate hydrogen, H{sub int}, increased upon heating. These results allow the different fractions to be characterized qualitatively on the basis of differences in hydrogen mobility. In mixtures of the continuous fractions, positive interactions occurred that enhanced the value of tan {delta} as well as the overall hydrogen mobility. A single maximum was observed in the tan {delta} response of these mixtures, which indicated that the heavier fractions were solvated through the action of the lighter ones. In a discontinuous mixture of the fractions, molecular interaction was slight compared to continuous mixtures; only the light fraction started to soften at low temperature and, as a result, a bimodal response occurred in tan {delta}. The thermoplastic response of coking coal can be modeled on a self-dissolution basis involving the {approximately}50% of solvent-soluble components that are present in whole coking coals and which possess a continuous fraction distribution from light to heavy. The mobility of the system develops continuously upon heating as a result of the progressive solvating action of the lighter components facilitating dissolution and/or dispersion of the heavier components. 25 refs., 7 figs., 2 tabs.

  13. Highly durable, coking and sulfur tolerant, fuel-flexible protonic ceramic fuel cells.

    Science.gov (United States)

    Duan, Chuancheng; Kee, Robert J; Zhu, Huayang; Karakaya, Canan; Chen, Yachao; Ricote, Sandrine; Jarry, Angelique; Crumlin, Ethan J; Hook, David; Braun, Robert; Sullivan, Neal P; O'Hayre, Ryan

    2018-05-01

    Protonic ceramic fuel cells, like their higher-temperature solid-oxide fuel cell counterparts, can directly use both hydrogen and hydrocarbon fuels to produce electricity at potentially more than 50 per cent efficiency 1,2 . Most previous direct-hydrocarbon fuel cell research has focused on solid-oxide fuel cells based on oxygen-ion-conducting electrolytes, but carbon deposition (coking) and sulfur poisoning typically occur when such fuel cells are directly operated on hydrocarbon- and/or sulfur-containing fuels, resulting in severe performance degradation over time 3-6 . Despite studies suggesting good performance and anti-coking resistance in hydrocarbon-fuelled protonic ceramic fuel cells 2,7,8 , there have been no systematic studies of long-term durability. Here we present results from long-term testing of protonic ceramic fuel cells using a total of 11 different fuels (hydrogen, methane, domestic natural gas (with and without hydrogen sulfide), propane, n-butane, i-butane, iso-octane, methanol, ethanol and ammonia) at temperatures between 500 and 600 degrees Celsius. Several cells have been tested for over 6,000 hours, and we demonstrate excellent performance and exceptional durability (less than 1.5 per cent degradation per 1,000 hours in most cases) across all fuels without any modifications in the cell composition or architecture. Large fluctuations in temperature are tolerated, and coking is not observed even after thousands of hours of continuous operation. Finally, sulfur, a notorious poison for both low-temperature and high-temperature fuel cells, does not seem to affect the performance of protonic ceramic fuel cells when supplied at levels consistent with commercial fuels. The fuel flexibility and long-term durability demonstrated by the protonic ceramic fuel cell devices highlight the promise of this technology and its potential for commercial application.

  14. Selective coke combustion by oxygen pulsing during Mo/ZSM‐5‐catalyzed methane dehydroaromatization

    NARCIS (Netherlands)

    Kosinov, N.; Coumans, F.J.A.G.; Uslamin, E.A.; Kapteijn, F.; Hensen, E.J.M.

    2016-01-01

    Non-oxidative methane dehydroaromatization is a promising reaction to directly convert natural gas into aromatic hydrocarbons and hydrogen. Commercialization of this technology is hampered by rapid catalyst deactivation because of coking. A novel approach is presented involving selective oxidation

  15. Research of Environmental and Economic Interactions of Coke And By-Product Process

    Science.gov (United States)

    Mikhailov, Vladimir; Kiseleva, Tamara; Bugrova, Svetlana; Muromtseva, Alina; Mikhailova, Yana

    2017-11-01

    The issues of showing relations between environmental and economic indicators (further - environmental and economic interactions) of coke and by-product process are considered in the article. The purpose of the study is to reveal the regularities of the functioning of the local environmental and economic system on the basis of revealed spectrum of environmental and economic interactions. A simplified scheme of the environmental and economic system "coke and by-product process - the environment" was developed. The forms of the investigated environmental-economic interactions were visualized and the selective interpretation of the tightness of the established connection was made. The main result of the work is modeling system of environmental and economic interactions that allows increasing the efficiency of local ecological and economic system management and optimizing the "interests" of an industrial enterprise - the source of negative impact on the environment. The results of the survey can be recommended to government authorities and industrial enterprises with a wide range of negative impact forms to support the adoption of effective management decisions aimed at sustainable environmental and economic development of the region or individual municipalities.

  16. The assessment of the coke wastewater treatment efficacy in rotating biological contractor.

    Science.gov (United States)

    Cema, G; Żabczyński, S; Ziembińska-Buczyńska, A

    2016-01-01

    Coke wastewater is known to be relatively difficult for biological treatment. Nonetheless, biofilm-based systems seem to be promising tool for such treatment. That is why a rotating biological contactor (RBC) system focused on the Anammox process was used in this study. The experiment was divided into two parts with synthetic and then real wastewater. It was proven that it is possible to treat coke wastewater with RBC but such a procedure requires a very long start-up period for the nitritation (190 days), as well as for the Anammox process, where stable nitrogen removal over 70% was achieved after 400 days of experiment. Interestingly, it was possible at a relatively low (20.2 ± 2.2 °C) temperature. The polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) based monitoring of the bacterial community showed that its biodiversity decreased when the real wastewater was treated and it was composed mainly of GC-rich genotypes, probably because of the modeling influence of this wastewater and the genotypes specialization.

  17. Estimation of the crack growth mechanism in the coking process. ; Behavior of fracture mechanics parameter. Cokes sonai kiretsu shinten ni kansuru ichikosatsu. ; Hakai rikigaku parameter no kyodo ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Yoshino, H; Sato, H; Nogami, H; Miura, T [Tohoku University, Sendai (Japan). Faculty of Engineering

    1991-07-10

    Cracks generated in coke layers during a coking furnace operation are an important factor not only to decide quality of the product, but also govern the energy consumption affecting the heat transfer and material transfer. This paper describes estimations of thermal stress and observations to fracture mechanics parameters, applying the incremental theory to surface cracks seen in the initial stage of carbonization. As a result of calculations using the crack tip opening displacement (CTOD) as a parameter to evaluate displacement in the vicinity of crack tips, the values increased with the increasing heating rate, and agreed qualitatively with the trend found in the experiments. The CTOD relates closely to the temperature dependence of the contraction coefficient, and varies largely at the transition point from the first maximum point to the second maximum point, from which the surface cracks are predicted to have been generated in this temperature region. Also, an estimation was made on the stress expansion coefficient from the stress distribution, and a result that can explain the experimental resultswas obtained. 10 refs., 11 figs.

  18. Obtainment of metallurgic coke from hydrolytic lignin of eucalyptus; Obtencao de coque metalurgico a partir de lignina hidrolitica de eucalipto

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, E.A. do [Escola Federal de Uberlandia, MG (Brazil). Dept. de Quimica; Schuchardt, U. [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica

    1987-12-31

    Eucalyptus lignin, obtained from COALBRA S.A., was briquetted under different humidities and pressures. The briquettes were heated to 900 Celsius at 1 C/min in a cylindric bench-scale oven. The cokification was accompanied by carbon-13 nuclear magnetic resonance measurements. The coke obtained was submitted to approximate and elementary analysis and its abrasion and compression strengths were determined. The distribution and total pore volume were investigated by high-pressure mercury porosimetry and the surface texture analyzed by scanning electron microscopy. The best coke was obtained in 48% yield from the briquettes with 10% humidity and 100 MPa pressure. This showed a high structural resistance, a smooth surface with continuous metallic brilliance and well defined pore volume and distribution. The coke obtained is a high-quality metallurgic reductant whose properties surpass by far the specifications required. (author). 12 refs., 1 fig., 2 tabs

  19. Coke formation in the oxidative dehydrogenation of ethylbenzene to styrene by TEOM

    NARCIS (Netherlands)

    Nederlof, C.; Vijfhuizen, P.; Zarubina, V.; Melian-Cabrera, I.; Kapteijn, F.; Makkee, M.

    2014-01-01

    A packed bed microbalance reactor setup (TEOM-GC) is used to investigate the formation of coke as a function of time-on-stream on gamma-Al2O3 and 3P/SiO2 catalyst samples under different conditions for the ODH reaction of ethylbenzene to styrene. All samples show a linear correlation of the styrene

  20. Coke formation in the oxidative dehydrogenation of ethylbenzene to styrene by TEOM

    NARCIS (Netherlands)

    Nederlof, C.; Vijfhuizen, P.; Zarubina, V.; Melián-Cabrera, I.; Kapteijn, F.; Makkee, M.

    2014-01-01

    A packed bed microbalance reactor setup (TEOM-GC) is used to investigate the formation of coke as a function of time-on-stream on ?-Al2O3 and 3P/SiO2 catalyst samples under different conditions for the ODH reaction of ethylbenzene to styrene. All samples show a linear correlation of the styrene

  1. Coke industry and steel metallurgy as the source of soil contamination by technogenic magnetic particles, heavy metals and polycyclic aromatic hydrocarbons.

    Science.gov (United States)

    Rachwał, Marzena; Magiera, Tadeusz; Wawer, Małgorzata

    2015-11-01

    Application of integrated magnetic, geochemical and mineralogical methods for qualitative and quantitative assessment of forest topsoils exposed to the industrial emissions was the objective of this manuscript. Volume magnetic susceptibility (κ) in three areas of southern Poland close to the coke and metallurgical plants was measured directly in the field. Representative topsoil samples were collected for further chemical and mineralogical analyses. Topsoil magnetic susceptibility in the studied areas depended mainly on the content of technogenic magnetic particles (TMPs) and decreased downwind at increasing distance from the emitters. In the vicinity of coking plants a high amount of polycyclic aromatic hydrocarbons (PAHs) was observed, especially the most carcinogenic ones with four- and five-member rings. No significant concentration of TMPs (estimated on the base of κ values) and heavy metals (HM) was observed in area where the coke plant was the only pollution source. In areas with both coke and metallurgical industry, higher amounts of TMPs, PAHs and HM were detected. Morphological and mineralogical analyses of TMPs separated from contaminated soil samples revealed their high heterogeneity in respect of morphology, grain size, mineral and chemical constitution. Pollution load index and toxicity equivalent concentration of PAHs used for soil quality assessment indicated its high level of pollution. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Polyphasic bacterial community analysis of an aerobic activated sludge removing phenols and thiocyanate from coke plant effluent

    Energy Technology Data Exchange (ETDEWEB)

    Felfoldi, T.; Szekely, A.J.; Goral, R.; Barkacs, K.; Scheirich, G.; Andras, J.; Racz, A.; Marialigeti, K. [Eotvos Lorand University, Budapest (Hungary). Dept. of Microbiology

    2010-05-15

    Biological purification processes are effective tools in the treatment of hazardous wastes such as toxic compounds produced in coal coking. In this study, the microbial community of a lab-scale activated sludge system treating coking effluent was assessed by cultivation-based (strain isolation and identification, biodegradation tests) and culture-independent techniques (sequence-aided T-RFLP, taxon-specific PCR). The results of the applied polyphasic approach showed a simple microbial community dominated by easily culturable heterotrophic bacteria. Comamonas badia was identified as the key microbe of the system, since it was the predominant member of the bacterial community, and its phenol degradation capacity was also proved. Metabolism of phenol, even at elevated concentrations (up to 1500 mg/L), was also presented for many other dominant (Pseudomonas, Rhodanobacter, Oligella) and minor (Alcaligenes, Castellaniella, Microbacterium) groups, while some activated sludge bacteria (Sphingomonas, Rhodopseudomonas) did not tolerate it even in lower concentrations (250 mg/L). In some cases, closely related strains showed different tolerance and degradation properties. Members of the genus Thiobacillus were detected in the activated sludge, and were supposedly responsible for the intensive thiocyanate biodegradation observed in the system. Additionally, some identified bacteria (e.g. C. badia and the Ottowia-related strains) might also have had a significant impact on the structure of the activated sludge due to their floc-forming abilities.

  3. The chemical and biological characteristics of coke-oven wastewater by ozonation

    International Nuclear Information System (INIS)

    Chang, E.-E.; Hsing, H.-J.; Chiang, P.-C.; Chen, M.-Y.; Shyng, J.-Y.

    2008-01-01

    A bench-scale bubble column reactor was used to investigate the biological and chemical characteristics of coke-oven wastewater after ozonation treatment through the examination of selected parameters. Color and thiocyanate could be removed almost entirely; however, organic matter and cyanide could not, due to the inadequate oxidation ability of ozone to remove ozonated byproducts under given experimental conditions. The removal of cyanide and total organic carbon were pH-dependent and were found to be efficient under neutral to alkaline conditions. The removal rate for thiocyanate was about five times that of cyanide. The ozone consumption ratio approached to about 1 at the early stage of ozonation (time TOC ) increased to 30%, indicating that easily degraded pollutants were degraded almost entirely. The effect of ozonation on the subsequent biological treatment unit (i.e., activated sludge process) was determined by observing the ratio of 5-day biological oxygen demand to chemical oxygen demand (BOD 5 /COD) and the specific oxygen utilization rate (SOUR). The results indicated that the contribution of ozonation to inhibition reduction was very significant but limited to the enhancement of biodegradation. The operation for ozonation of coke-oven wastewater was feasible under neutral condition and short ozone contact time in order to achieve better performance and cost savings

  4. Neutron and gamma-ray transmission technique for the on-line determination of moisture in coal and coke

    International Nuclear Information System (INIS)

    Sowerby, B.D.; Millen, M.J.; Rafter, P.T.

    1985-01-01

    A fast neutron and gamma-ray transmission technique is being developed for the on-line analysis of moisture in coal and coke. The technique utilises 252 Cf and 137 Cs sources and 3 He and NaI(Tl) detectors. Laboratory measurements on single coal samples have shown that moisture can be determined to better than 1 wt% over the range 0 to 16 wt% moisture and 5 to 17cm thickness. Reduced errors were obtained for restricted ranges of moisture and thickness. Preliminary measurements on coke of thickness 30 to 50cm have shown that moisture can be determined to within 0.26 wt% over the range 1 to 16 wt% moisture

  5. Coke burning behavior of a catalyst of ZSM-5/ZSM-11 co-crystallized zeolite in the alkylation of benzene with FCC off-gas to ethylbenzene

    Energy Technology Data Exchange (ETDEWEB)

    Song, Yi; Zhai, Yuchun [Northeastern University, Shenyang, 110006 (P. R. China); Liu, Shenglin; Wang, Qingxia; Xu, Longya [State Key Laboratory of Catalysis, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, P. O. Box 110, Dalian 116023 (P. R. China)

    2006-04-15

    Since the commercialization of ethylbenzene production via alkylation of benzene with the dilute ethene in FCC off-gas over a ZSM-5/ZSM-11 co-crystallized zeolite catalyst in China, the catalyst has been regenerated several times and showed good regeneration performance. During the alkylation process, the catalytic activity decreases, some of the catalyst pores are blocked and the acid centers are partly covered by coke deposition. Influence of the factors such as catalyst particle size, temperature, etc. on the burning rate of the coke was investigated by the TG technique, and a rate equation for coke burning on the ZSM-5/ZSM-11 co-crystallized catalyst was established. (author)

  6. Smoking modify the effects of polycyclic aromatic hydrocarbons exposure on oxidative damage to DNA in coke oven workers.

    Science.gov (United States)

    Yang, Jin; Zhang, Hongjie; Zhang, Huitao; Wang, Wubin; Liu, Yanli; Fan, Yanfeng

    2017-07-01

    Coke oven emissions containing polycyclic aromatic hydrocarbons (PAHs) are predominant toxic constituents of particulate air pollution that have been linked to increased risk of lung cancer. Numerous epidemiological studies have suggested that oxidative DNA damage may play a pivotal role in the carcinogenic mechanism of lung cancer. Little is known about the effect of interaction between PAHs exposure and lifestyle on DNA oxidative damage. The study population is composed by coke oven workers (365) and water treatment workers (144), and their urinary levels of four PAH metabolites and 8-hydroxydeoxyguanosine (8-OHdG) were determined. Airborne samples of exposed sites (4) and control sites (3) were collected, and eight carcinogenic PAHs were detected by high-performance liquid chromatography. The median values of the sum of eight carcinogenic PAHs and BaP in exposed sites were significantly higher than control sites (P < 0.01). The study found that the urinary PAH metabolites were significantly elevated in coke oven workers (P < 0.01). Multivariate logistic regression analysis revealed that the risk of high levels of urinary 8-OHdG will increase with increasing age, cigarette consumption, and levels of urinary 1-hydroxypyrene, and P for trend were all <0.05. Smoking can significantly modify the effects of urinary 1-hydroxypyrene on high concentrations urinary 8-OHdG, during co-exposure to both light or heavy smoking and high 1-hydroxypyrene levels (OR 4.28, 95% CI 1.32-13.86 and OR 5.05, 95% CI 1.63-15.67, respectively). Our findings quantitatively demonstrate that workers exposed to coke oven fumes and smoking will cause more serious DNA oxidative damage.

  7. Synergetic effects leading to coke-resistant NiCo bimetallic catalysts for dry reforming of methane

    KAUST Repository

    Li, Lidong; Anjum, Dalaver; Zhu, Haibo; Saih, Youssef; Laveille, Paco; D'Souza, Lawrence; Basset, Jean-Marie

    2015-01-01

    A new dry reforming of methane catalyst comprised of NiCo bimetallic nanoparticles and a Mgx(Al)O support that exhibits high coke resistance and long-term on-stream stability is reported. The structural characterization by XRD, TEM, temperature

  8. The analysis of coal-and coke ashes by atomic absorption spectrophotometry

    International Nuclear Information System (INIS)

    Coutinho, C.A.; Prates, H.T.; Pereira, C.P.

    1977-01-01

    In order to provide better conditions for the control of the chemical composition of the load in the USIMINAS blast furnaces, a method of analysis for sodium, potassium, iron, aluminium, calcium, magnesium and maganese in coal-and coke ash by atomic absorption spectrophotometry was developed. The precision of the calibration curves and the reproducibility of the results are given, together with an estimate of the speed compared with conventional methods of chemical analysis [pt

  9. The error analysis of coke moisture measured by neutron moisture gauge

    International Nuclear Information System (INIS)

    Tian Huixing

    1995-01-01

    The error of coke moisture measured by neutron method in the iron and steel industry is analyzed. The errors are caused by inaccurate sampling location in the calibration procedure on site. By comparison, the instrument error and the statistical fluctuation error are smaller. So the sampling proportion should be increased as large as possible in the calibration procedure on site, and a satisfied calibration effect can be obtained on a suitable size hopper

  10. Anode performance of boron-doped graphites prepared from shot and sponge cokes

    Science.gov (United States)

    Liu, Tao; Luo, Ruiying; Yoon, Seong-Ho; Mochida, Isao

    The structures and anode performances of graphitized pristine and boron-doped shot and sponge cokes have been comparatively studied by means of scanning electron microscope (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and galvanostatic measurement. The results show that high degree of graphitization can be obtained by the substituted boron atom in the carbon lattice, and boron in the resultant boron-doped graphites mainly exist in the form of boron carbide and boron substituted in the carbon lattice. Both of boron-doped graphites from shot and sponge cokes obtain discharge capacity of 350 mAh g -1 and coulombic efficiency above 90%. Apart from commonly observed discharge plateau for graphite, boron-doped samples in this study also show a small plateau at ca. 0.06 V. This phenomenon can be explained that Li ion stores in the site to be void-like spaces that are produced by "molecular bridging" between the edge sites of graphene layer stack with a release of boron atoms substituted at the edge of graphene layer. The effect of the amount of boron dopant and graphitization temperature on the anode performance of boron-doped graphite are also investigated in this paper.

  11. Treatment of coking wastewater by a novel electric assisted micro-electrolysis filter.

    Science.gov (United States)

    Xie, Ruosong; Wu, Miaomiao; Qu, Guangfei; Ning, Ping; Cai, Yingying; Lv, Pei

    2018-04-01

    A newly designed electric assisted micro-electrolysis filter (E-ME) was developed to investigate its degradation efficiency for coking wastewater and correlated characteristics. The performance of the E-ME system was compared with separate electrolysis (SE) and micro-electrolysis (ME) systems. The results showed a prominent synergistic effect on COD removal in E-ME systems. Gas chromatography/mass spectrometry (GC-MS) analysis confirmed that the applied electric field enhanced the degradation of phenolic compounds. Meanwhile, more biodegradable oxygen-bearing compounds were detected. SEM images of granular activated carbon (GAC) showed that inactivation and blocking were inhibited during the E-ME process. The effects of applied voltage and initial pH in E-ME systems were also studied. The best voltage value was 1V, but synergistic effects existed even with lower applied voltage. E-ME systems exhibited some pH buffering capacity and attained the best efficiency in neutral media, which means that there is no need to adjust pH prior to or during the treatment process. Therefore, E-ME systems were confirmed as a promising technology for treatment of coking wastewater and other refractory wastewater. Copyright © 2017. Published by Elsevier B.V.

  12. Thermogravimetric analysis in the characterization of colombian coals used in the production of coke

    International Nuclear Information System (INIS)

    Guerrero, Camilo; Salamanca, Monica E; Diaz, Jose de J

    2010-01-01

    Five types of coal from the states of Cundinamarca, Boyaca and Norte de Santander (Colombia) were characterized by proximate, ultimate, rheological, petrographic, calorific and thermogravimetric analysis. The parameters used, especially the ones which determine the rheological properties show that the studied coals and its blends could produce good quality coke. It was observed the inverse relationship between the volatile matter content and the mean vitrinite reflectance, relationship which is attributed to the increase of the aromaticity in the molecular structure of the coal as a consequence of the rank increase. The parameters derived from the thermogravimetric analysis, maximum velocity of de-volatilization and the temperature of maximum velocity of de-volatilization and the media reflectance of the vitrinite showed good correlations. Also was observed an interesting correlation between the velocity of de-volatilization and maximum fluidity. This shows that the thermogravimetric analysis can be a useful tool to characterize in a quick way coals used for metallurgical coke production.

  13. Preparation of activated petroleum coke for removal of naphthenic acids model compounds: Box-Behnken design optimization of KOH activation process.

    Science.gov (United States)

    Niasar, Hojatallah Seyedy; Li, Hanning; Das, Sreejon; Kasanneni, Tirumala Venkateswara Rao; Ray, Madhumita B; Xu, Chunbao Charles

    2018-04-01

    This study employed Box-Behnken design and response surface methodology to optimize activation parameters for the production of activated petroleum coke (APC) adsorbent from petroleum coke (PC) to achieve highest adsorption capacity for three model naphthenic acids. Activated petroleum coke (APC) adsorbent with a BET surface area of 1726 m 2 /g and total pore volume of 0.85 cc/g was produced at the optimum activation conditions (KOH/coke mass ratio) of 3.0, activation temperature 790 °C, and activation time 3.47 h). Effects of the activation parameters on the adsorption pefromances (adsortion capaciy and kinetics) were investigated. With the APC obtained at the optimum activation condition, the maximum adsorption capacity of 451, 362, and 320 (mg/g) was achieved for 2-naphthoic acid, diphenylacetic acid and cyclohexanepentanoic acid (CP), respectively. Although, generally APC adsorbents with a higher specific surface area and pore volume provide better adsorption capacity, the textural properties (surface areas and pore volume) are not the only parameters determining the APC adsorbents' adsorption capacity. Other parameters such as surface functionalities play effective roles on the adsorption capacity of the produced APC adsorbents for NAs. The KOH activation process, in particular the acid washing step, distinctly reduced the sulfur and metals contents in the raw PC, decreasing the leaching potential of metals from APC adsorbents during adsorption. Copyright © 2018 Elsevier Ltd. All rights reserved.

  14. Instability of biological nitrogen removal in a cokes wastewater treatment facility during summer

    International Nuclear Information System (INIS)

    Kim, Young Mo; Park, Donghee; Lee, Dae Sung; Park, Jong Moon

    2007-01-01

    Failure in nitrogen removal of cokes wastewater occurs occasionally during summer season (38 deg. C) due to the instability of nitrification process. The objective of this study was to examine why the nitrification process is unstable especially in summer. Various parameters such as pH, temperature, nutrients and pollutants were examined in batch experiments using activated sludge and wastewater obtained from a full-scale cokes wastewater treatment facility. Batch experiments showed that nitrification rate of the activated sludge was faster in summer (38 deg. C) than in spring or autumn (29 deg. C) and the toxic effects of cyanide, phenol and thiocyanate on nitrification were reduced with increasing temperature. Meanwhile, experiment using continuous reactor showed that the reduction rate in nitrification efficiency was higher at 38 deg. C than at 29 deg. C. In conclusion, the instability of full-scale nitrification process in summer might be mainly due to washing out of nitrifiers by fast growth of competitive microorganisms at higher temperature under increased concentrations of phenol and thiocyanate

  15. Engineering solutions to improve environmental characteristics of coke-chemical industry

    Energy Technology Data Exchange (ETDEWEB)

    Lavrov, K G; Cherkashina, O I; Pushkarev, G P; Pakhomov, V A; Florinskii, N V; Oleinik, K P; Likhogub, E P; Dorfman, G A; Gorelik, Ya L; Vorona, V K

    1979-06-01

    In future projects consideration will be given to reduction of air and water pollution. Escape of dust from coke-batteries and coal preparation plants will be stopped by using hermetic enclosures with aspirators. Effluent gases and vapours will be curbed by using more efficient scrubbers and flare systems. Effluent waters will be treated at two-stage flotation stations and recycled to 95% as cooling and utility water. Cooling water consumption will be reduced by the use of air coolers. Pollution monitoring will be improved.

  16. Tried and True: Using Diet Coke and Mentos to Teach Scientific Inquiry

    Science.gov (United States)

    Murray, Tracey Arnold

    2011-01-01

    Adding mint Mentos candy to a two-liter bottle of Diet Coke produces a fountain of soda foam that can reach 3 m high. A demonstration such as this can get a "Wow" out of most audiences, usually followed by a "Do it again!"--but can it be used to teach anything? The answer is a definite "Yes," and what follows is a guided inquiry activity that…

  17. Municipal solid waste disposal by using metallurgical technologies and equipments

    Energy Technology Data Exchange (ETDEWEB)

    Cai, Jiuju; Sun, Wenqiang [State Environmental Protection Key Laboratory of Eco-industry, Institute of Thermal and Environmental Engineering, Northeastern University, Shenyang 110819 (China)

    2012-07-01

    Pyrolysis of municipal solid waste can take full advantage of energy and resource and avoid producing hazardous material during this period. In combination with mature metallurgical technologies of coking by coke oven, regenerative flame furnace technology and melting by electric arc furnace, technologies of regenerative fixed bed pyrolysis technology for household waste, co-coking technology for waste plastic and blend coal, and incineration ash melting technology by electric arc technology for medical waste were respectively developed to improve current unsatisfied sorting status of waste. The investigation results of laboratory experiments, semi-industrial experiments and industrial experiments as well as their economic benefits and environmental benefits for related technologies were separately presented.

  18. High-BTU gas production from tar-bearing hot coke oven gas over iron catalyst

    Energy Technology Data Exchange (ETDEWEB)

    L.Y. Li; K. Morishita; T. Takarada [Gunma University, Gunma (Japan). Department of Biological and Chemical Engineering

    2005-07-01

    To utilize the tar-bearing hot coke oven gas (the by-product of coke making process) more effectively, a process was developed by converting the hot coke oven gas into a methane rich high-BTU gas over iron-bearing catalysts. The catalytic behaviour of Indonesian limonite ore was mainly discussed. For a reference, a conventional nickel catalyst (Ni/Al{sub 2}O{sub 3}) was employed. Laboratory scale tests were carried out in a two-stage fixed-bed reactor at ambient pressure. A bituminous coal sample was heated at first stage, the volatiles was carried by feed gas and decomposed at second stage. The limonite promoted hydropyrolysis of coal volatiles similar to Ni/Al{sub 2}O{sub 3} catalyst. High yields of total product gas and methane were obtained at 50 vol.% hydrogen atmosphere with a feed gas of 60 ml min{sup -1} hydrogen and 60 ml min{sup -1} nitrogen. After experiments, hydrocarbons heavier than ethane were not observed. Also that, carbon balance was more than 99.8% in coal char, product gases and carbon deposits. It was considered that coal volatiles converted into light gases and carbon almost completely in catalyst bed. Yields of product gas and methane depended upon catalytic temperature. At 923 K, the maximum yield of product gas was achieved at 74.3% for limonite catalyst on carbon balance with methane 83.2 vol.% of the carbonaceous gas products. Comparing with limonite, Fe/Al{sub 2}O{sub 3} and BOF dust samples showed low activities on coal volatiles catalytic decomposition. 21 refs., 5 figs., 3 tabs.

  19. Association of urinary metals levels with type 2 diabetes risk in coke oven workers

    International Nuclear Information System (INIS)

    Liu, Bing; Feng, Wei; Wang, Jing; Li, Yaru; Han, Xu; Hu, Hua; Guo, Huan; Zhang, Xiaomin; He, Meian

    2016-01-01

    Background: Studies indicated that occupationally exposed to metals could result in oxidative damage and inflammation and increase cardiovascular diseases risk. However, epidemiological studies about the associations of metals exposure with diabetes risk among coke oven workers were limited. Objectives: This study aims to investigate the potential associations of 23 metals levels with the risk of diabetes among coke oven workers. Methods: The analysis was conducted in a cross-sectional study including 1493 participants. Urinary metals and urinary polycyclic aromatic hydrocarbons (PAHs) metabolites levels were determined by inductively coupled plasma mass spectrometer and gas chromatograph-mass spectrometer respectively. Multivariate logistic regression was used to investigate the associations of urinary metal levels with diabetes risk with adjustment for potential confounding factors including gender, age, BMI, education, smoking, drinking, physical activity, hypertension, hyperlipidemia and urinary PAHs metabolites levels. Results: Compared with the normoglycemia group, the levels of urinary copper, zinc, arsenic, selenium, molybdenum, and cadmium were significantly higher in the diabetes group (all p < 0.05). Participants with the highest tertile of urinary copper and zinc had 2.12 (95%CI: 1.12–4.01) and 5.43 (95%CI: 2.61–11.30) fold risk of diabetes. Similar results were found for hyperglycemia risk. Besides, participants with the highest tertile of manganese, barium, and lead had 1.65(1.22–2.23), 1.60(1.19–2.16) and 1.45(1.05–1.99) fold risk of hyperglycemia when compared with the lowest tertlie. Conclusion: The results indicated that the urinary copper and zinc levels were positively associated with the risk of diabetes and hyperglycemia among coke oven workers. Urinary manganese, barium and lead levels were also associated with increased risk of hyperglycemia independently of other traditional risk factors. These findings need further validation

  20. The Homecourt coke plant site: a successful redeveloped brown field case

    International Nuclear Information System (INIS)

    Charbonnier, P.; Piguet, O.; Lereboullet, L.

    2006-01-01

    The environmental diagnosis of the coke plant site in Homecourt has been carried out over the last 15 years. Bail Industrie has selected two zones on the site for a remediation program in view of their further redevelopment. The weakly polluted grounds were submitted to a bio treatment, while the more polluted grounds were treated by thermal desorption. Tars have been incinerated off site. To assess the effectiveness of the treatment, percolation tests are carried out. (authors)

  1. Producing hydrogen from coke-oven gas: the Solmer project. [PSA process

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, G; Vidal, J

    1984-05-01

    After presenting the energy situation at the Solmer plant, where coke-oven gas is produced to excess, the authors examine the technical and economic possibilities of utilizing this gas for hydrogen extraction. They describe a project (based on the PSA process) for producing some 65 t/d of hydrogen and present the technical features of the scheme. An evaluation of the energy and financial costs of producing the hydrogen confirms the competitive status of the process.

  2. Coke properties in relation to charge preparation techniques. [Selective crushing

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, O S

    1979-01-01

    Selective crushing is essential to obtain the required coke properties, so that in the coarse fractions there is a considerable reduction in the middlings and dirt normally difficult to crush. These are at the same time enriched with vitrinite so that there is an increase in the coal substance as such, reflected in improved caking capacity in the coarse size range. Various methods of selective crushing are employed, including air entrainment mills, fluidised bed systems. Other advantages claimed for selective crushing are the uniform pore distribution and air permeability and also the diminished breakage stress.

  3. Dependence of coke properties on the method of charge preparation

    Energy Technology Data Exchange (ETDEWEB)

    Morozov, O S

    1979-04-01

    Selective crushing is essential to obtain the required coke properties, so that in the coarse fractions there is a considerable reduction in the middlings and dirt normally difficult to crush. These are at the same time enriched with vitrinite so that there is an increase in the coal substance as such, reflected in improved caking capacity in the coarse size range. Various methods of selective crushing are employed, including air entrainment mills, fluidised bed systems. Other advantages claimed for selective crushing are the uniform pore distribution and air permeability and also the diminished breakage stress.

  4. Method of pyrolytic decomposition and coking of a mixture of finely distributed solid or semisolid carbonaceous material and hydrocarbon oils

    Energy Technology Data Exchange (ETDEWEB)

    1933-09-09

    A method of pyrolytic decomposition and coking of a mixture of finely distributed of solid or semi-solid carbonaceous material and hydrocarbon oils is disclosed whereby the mixture is exposed to a decomposition temperature and later is brought into the zone of decomposition where vapors are separated from the unvaporized residue and the vapors are exposed to fractional condensation for the purpose of obtaining a light product of distillation. The method is characterized by the mixture being exposed to heating by means of indirect exchange of heat in a heating zone or by means of a direct addition of a hot heat-conducting medium, or by means of both the mentioned indirect exchange of heat and direct heat under such conditions that the unvaporized residue obtained from the thus-heated mixture in the decomposition zone is transformed to solid coke in this zone by being heated to coking temperature in a comparatively thin layer on the surface of the decomposition zone that has been heated to a high temperature.

  5. Combustion reactivity of chars from copyrolysis of coal with coke-oven gas

    Energy Technology Data Exchange (ETDEWEB)

    Liao Hongqiang; Sun Chenggong; Li Baoqing [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

    1997-12-31

    The combustion reactivity of char from pyrolysis of Xianfeng lignite with coke-oven gas (COG) is related to the pyrolysis pressure and heating rate. Decreasing pressure and increasing heating rate enhance the char yields and combustion reactivity. The combustion reactivities of char from coal pyrolysis with COG nearly reach to that of char from hydropyrolysis, but lower than those of char from coal pyrolysis under N{sub 2}. (orig.)

  6. Mini-PROven. Reduced emissions from small and medium-size coke ovens thanks to single-chamber pressure control; Mini-PROven. Emissionsreduzierung an kleinen und mittleren Koksoefen mit einer Einzelkammerdruckregelung

    Energy Technology Data Exchange (ETDEWEB)

    Huhn, Friedrich; Krebber, Frank; Kuehn-Gajdzik, Joanna; Ueberschaer, Kerstin [ThyssenKrupp Uhde GmbH, Dortmund (Germany). Coke Plant Technologies Div.

    2012-07-01

    For environment and occupational health reasons it is becoming increasingly important for coke plants to be operated with the lowest possible level of emissions. In the past, changing pressure conditions in each individual oven, with particularly high values at the beginning of the coking period, often resulted in considerable emissions at the oven closures. To prevent this happening on modern large-scale ovens, ThyssenKrupp Uhde developed the PROven trademark (Pressure Regulated Oven), a single-chamber pressure control system which regulates the pressure in the individual coke chambers down to a constantly low level. In the meantime, after many years of successful service, the system has been upgraded in both its design and process engineering. The result is Mini-PROven, which in future can also be retro-fitted to old small and medium-size coke oven batteries in the interest of better environmental protection. (orig.)

  7. Research of coal flash hydropyrolysis. I. Chemical type analysis of nitrogen in coal and semi-coke

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, H.; Ni, Y.; Tang, L.; Zheng, Z.; Zhu, Z. [East China University of Science and Technology, Shanghai (China)

    2001-04-01

    Using XPS analyses the chemical types of nitrogen of ten different types of Chinese coals and their semi-cokes from flash hydropyrolysis (FHP) are studied. The results shows that XPS can effectively determined the chemical types of nitrogen in coal and semi-coke. Peak of XPS located in 398.8 ({plus_minus}0.1) eV and 400.2 ({plus_minus}0.1) eV, which corresponds to pyrrole and pyridine. The nitrogen types are different in coals but mainly are pyrrole and pyridine, and often the pyrrole is more than pyridine. The nitrogen type in coals from FHP is the same as in coal. In FHP, the relative content of pyrrole increases and pyridine reduces. Therefore, it was put forward that flash hydropyrolysis is a new important clean-coal technique and has notable effect of denitrogenation.

  8. Synthesis of carbon nanotubes by gasification of petroleum coke

    International Nuclear Information System (INIS)

    Abdullayeva, S.H.; Musayeva, N.N.; Jabbarov, R.B.; Abdullayeva, S.H.; Musayeva, N.N.; Jabbarov, R.B.; Matsuda, T.

    2013-01-01

    Carbon nanotubes have been synthesized by using petroleum coke (PC) as carbon source. Different positions of the PC in the reactor chamber and some other factors markedly increase quantity of the synthesized CNTs and lead to changing of their characteristics such as crystallinity, diameter, straight and etc. confirmed by scanning electron microscope (SEM), transmission electron microscope (TEM) studies.The thickness of the Fe catalyst deposited on Si and SiO 2 substrates strongly influence to the quality, quantity and uniformity of the grown CNTs. Wet-coated thin films of FeCl 2 works well as catalyst, which can be profitable for mass production of CNTs

  9. Coking coal consumption of POSCO

    International Nuclear Information System (INIS)

    Yoo, B.C.

    1991-01-01

    Pohang Iron and Steel Company Limited (POSCO) was established in 1968. Molten iron was first produced in July 1973 after a 3 year construction period. The long awaited start up of Korea's first integrated steel works provided the momentum for the fast growth of our steel industry. In 1973, the first year of operation, POSCO purchased 770,000 tons of coal from the United States and Australia. The import tonnage was more than doubled in 1976 when we completed the second stage of Pohang Works and has continued to increase reaching 13.1 million tons last year. POSCO's coal consumption will increase one more time next year as the fourth stage of Kwangyang works starts to operate a new blast furnace with an annual molten iron production capacity of 2.8 million tons. Even though the new blast furnace will have the same capacity as the other 3 in Kwangyang, the additional coking coal requirement will be much smaller than the tonnages we needed for the other stages of the works. This paper reports that this is due to the increased use of pulverized coal

  10. Anode performance of boron-doped graphites prepared from shot and sponge cokes

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Tao; Luo, Ruiying [School of Science, Beihang University, Beijing 100083 (China); Yoon, Seong-Ho; Mochida, Isao [Institute for Materials Chemistry and Engineering, Kyushu University, Kasuga, Fukuoka 816-8580 (Japan)

    2010-03-15

    The structures and anode performances of graphitized pristine and boron-doped shot and sponge cokes have been comparatively studied by means of scanning electron microscope (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and galvanostatic measurement. The results show that high degree of graphitization can be obtained by the substituted boron atom in the carbon lattice, and boron in the resultant boron-doped graphites mainly exist in the form of boron carbide and boron substituted in the carbon lattice. Both of boron-doped graphites from shot and sponge cokes obtain discharge capacity of 350 mAh g{sup -1} and coulombic efficiency above 90%. Apart from commonly observed discharge plateau for graphite, boron-doped samples in this study also show a small plateau at ca. 0.06 V. This phenomenon can be explained that Li ion stores in the site to be void-like spaces that are produced by ''molecular bridging'' between the edge sites of graphene layer stack with a release of boron atoms substituted at the edge of graphene layer. The effect of the amount of boron dopant and graphitization temperature on the anode performance of boron-doped graphite are also investigated in this paper. (author)

  11. Petroleum Coke in the Urban Environment: A Review of Potential Health Effects

    Directory of Open Access Journals (Sweden)

    Joseph A. Caruso

    2015-05-01

    Full Text Available Petroleum coke, or petcoke, is a granular coal-like industrial by-product that is separated during the refinement of heavy crude oil. Recently, the processing of material from Canadian oil sands in U.S. refineries has led to the appearance of large petcoke piles adjacent to urban communities in Detroit and Chicago. The purpose of this literature review is to assess what is known about the effects of petcoke exposure on human health. Toxicological studies in animals indicate that dermal or inhalation petcoke exposure does not lead to a significant risk for cancer development or reproductive and developmental effects. However, pulmonary inflammation was observed in long-term inhalation exposure studies. Epidemiological studies in coke oven workers have shown increased risk for cancer and chronic obstructive pulmonary diseases, but these studies are confounded by multiple industrial exposures, most notably to polycyclic aromatic hydrocarbons that are generated during petcoke production. The main threat to urban populations in the vicinity of petcoke piles is most likely fugitive dust emissions in the form of fine particulate matter. More research is required to determine whether petcoke fine particulate matter causes or exacerbates disease, either alone or in conjunction with other environmental contaminants.

  12. 77 FR 20788 - Foundry Coke Products From the People's Republic of China: Final Results of Expedited Second...

    Science.gov (United States)

    2012-04-06

    ... mm (4 inch) sieve, of a kind used in foundries. The foundry coke products subject to the antidumping... purposes, our written description of the scope of the Order is dispositive. Analysis of Comments Received...

  13. Test Report Emission Test Program EPA Information Collection Request for Delayed Coking Units 736 Coker Unit

    Science.gov (United States)

    ARI Environmental, Inc. (ARI) was retained by Houston Refining LP (HRO) to conduct an emission test program at their refinery located in Houston, Texas. The testing was conducted on on the 736 Delayed Coking Unit (DCU) in response to EPA's ICR.

  14. Contribution to the assessment of sampling data of coke. Beitrag zur Auswertung von Probenahme-ergebnissen von Koks

    Energy Technology Data Exchange (ETDEWEB)

    Goell, G; Helfricht, R; Mueller, H [Forschungsinstitut fuer Aufbereitung, Freiberg (Germany, F.R.)

    1991-03-01

    Controlling the quality characteristics of disperse material systems in plants where these are produced and applied, by means of test procedures, assumes that samples are taken from mass flows. In this contribution, a report is presented on research on the clarification of the causes of fluctuations and differences of test results for coke between supplier and customer. It is revealed that for an appraisal, prehistory and material behaviour of the test material as well as analysis of the actual condition of the sampling and processing systems of both plants are to be considered. The magnitude of the individual error in relation to the total sampling error is explored and conclusions are drawn, to rule out differences as well as unfavourable developments in the production, utilization and the appraisal of coke products. 15 refs., 7 figs.

  15. Co-pyrolysis of coal with hydrogen-rich gases. 1. Coal pyrolysis under coke-oven gas and synthesis gas

    Energy Technology Data Exchange (ETDEWEB)

    Liao, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion

    1998-06-01

    To improve the economics of the hydropyrolysis process, it has been suggested that cheaper hydrogen-rich gases (such as coke oven gas, synthesis gas) could be used instead of pure hydrogen. Pyrolysis of Chinese Xianfeng lignite was carried out with coke oven gas (COG) and synthesis gas (SG) as reactive gases at 0.1-5 MPa and at a final temperature up to 650{degree}C with a heating rate of 5-25{degree}C min{sup -1} in a 10 g fixed-bed reactor. The results indicate that it is possible to use COG and SG instead of pure hydrogen in hydropyrolysis, but that the experimental conditions must be adjusted to optimize the yields of the valuable chemicals. 14 refs., 3 figs., 6 tabs.

  16. A comparison study on the deoxygenation of coal mine methane over coal gangue and coke under microwave heating conditions

    International Nuclear Information System (INIS)

    Guo, Xuan; Ren, Jun; Xie, Chuanjin; Lin, Jianying; Li, Zhong

    2015-01-01

    Highlights: • Microwave has great advantages of energy and time saving in CMM deoxygenation. • Microwave pretreatment results in graphitization of carbonaceous materials. • Coal gangue shows benefit in restricting CH 4 decomposition compared to coke. • Under optimal conditions, there is no residual oxygen and CH 4 is less than 2.2%. - Abstract: Microwave heating has great advantages in saving energy and time; in this study, it has been first successfully applied in the deoxidization process of coal mine methane (CMM), where carbon in coal gangue reacts with oxygen in CMM. Compared with traditional heating, microwave pretreatment resulted in rapid heating of coal gangue in CMM deoxygenation, which was attributable to the graphitization of carbonaceous materials. This prominent advantage of microwave heating can contribute to deoxygenation. In addition, deoxygenation effectiveness for both coke and coal gangue under microwave heating was investigated. It was discovered that coke acted as a catalyst to some extent to accelerate methane decomposition. However, this effect could be greatly restricted when coal gangue was used in the deoxygenation process because of its chemical inertness. Under optimal conditions (650 °C and 300 mL/min), there was no residual oxygen in the outlet gas, and methane loss was less than 2.2%

  17. Study of burden distribution characteristics (IV): the development of a distribution predicting model in which coke collapse has been taken into account

    Energy Technology Data Exchange (ETDEWEB)

    Kamisaka, E; Okuno, Y; Irita, T; Matsuzaki, M; Isoyama, T; Kunitomo, K

    1984-01-01

    Using results quoted in a previous report (see Tetsu To Hagane, Vol. 68, page S 701, 1982), coke collapse has been quantified by means of landslide theory, according to which the stability of the burden is given by a safety factor which equals resistance moment/sliding moment. This has enabled coke collapse to be introduced in a model for predicting burden distribution. Application of this model has resulted in more accurate predictions of burden distribution, the computed values being in close agreement with the results of distribution experiments. 1 reference.

  18. Investigation on the co-combustion of low calorific oil shale and its semi-coke by using thermogravimetric analysis

    International Nuclear Information System (INIS)

    Yang, Yu; Lu, Xiaofeng; Wang, Quanhai

    2017-01-01

    Highlights: • The co-combustion characteristic parameters were studied. • The co-combustion of oil shale and semi-coke could be expressed roughly by the addition of individual components. • Activation energy was calculated by Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. - Abstract: In the present work, thermogravimetric analysis was employed to investigate co-combustion behaviors of Fushun low calorific oil shale and its semi-coke. The synergy effect was estimated by using the interaction coefficient and the relative error of mean square root. In addition, activation energy was also calculated by means of Coats-Redfern, distributed activation energy model and Flynn-Wall-Ozawa methods. Results indicated that with the increase of oil shale mass fraction and oxygen concentration, combustion characteristics of the samples were improved. And some little interaction did occur during the co-combustion process, but it was relatively slight. Consequently, the co-combustion of oil shale and semi-coke still could be expressed roughly by the addition of individual components of the mixtures. Furthermore, activation energy of the samples decreased slowly at the initial stage attributed to the minerals’ catalytic effects, and in the final stage, it jumped to a high value, suggesting that the burnout of the samples was difficult. Besides, the mix proportion of oil shale which was added to stabilize the combustion in the circulating fluidized bed was also theoretically calculated.

  19. Estimation of the thermal stress in the coke layer. Kanryu katei ni okeru kokusu sonai netsuoryoku no suisan

    Energy Technology Data Exchange (ETDEWEB)

    Miura, Takatsoshi; Yoshino, Hiroyuki; Saito, Shozaburo; Otani, Shigemori [Tohoku Univ., Sendai (Japan). Faculty of Engineering

    1989-12-20

    Fissures which are formed in coke ovens are an important factor which exerts influences not only on the quality of coke but also on consumed energy such as thermal transfer. An estimation method of thermal stress distribution in the coke layer which is important to determine these fissures was, therefore, proposed, and the propriety of the method was demonstrated in comparison with the experiment results by X-ray computerized tomography. In the analysis model, heat fluxes from the upper part of the carbonization room and from the heating wall were regarded the same, and the temperature field was obtained by formulating the non-steady heat conduction equation to the finite element method by Galerkin scheme. The stress field was presumed to be an elastic flat field, and it was formulated to the finite element method by the incremental theory. Following investigation results were obtained and thus the propriety of this method was demonstrated. The formation position of principal tensile stress calculated and the formation position of fissures observed by X-ray computerized tomography had a corresponding relation. According to the calculation, with the increase of heating rate, principal tensile stress was increased; and that accounted for experiment results. Estimated results of thermal stress in the layer varied depending on the coal's value of property of the matter. 8 refs., 15 figs., 2 tabs.

  20. Purification of coke oven wastewater; Depuracion de aguas residuales de coqueria

    Energy Technology Data Exchange (ETDEWEB)

    Rancano, A.; Gutierrez, A.; Diaz, J.M.

    1998-06-01

    Coke oven wastewater are one of the most problematic that are produced by the iron and steel industry. They must be purified to minimise their impact on the environment. In this work a general vision about the different treatments that the wastewater must subject before being poured is showed. The options and efficiencies of every step were studied, taking special attention to the organic removal, studying the different ways to carry out this removal, centring on the biological treatment, the most used in this kind of wastewaters. (Author) 35 refs.

  1. Electrochemical improvement of low-temperature petroleum cokes by chemical oxidation with H2O2 for their use as anodes in lithium ion batteries

    International Nuclear Information System (INIS)

    Concheso, A.; Santamaria, R.; Menendez, R.; Jimenez-Mateos, J.M.; Alcantara, R.; Lavela, P.; Tirado, J.L.

    2006-01-01

    The electrochemical performance of non-graphitized petroleum cokes has been improved by mild oxidation using hydrogen peroxide, a procedure used for the first time in these materials. For this purpose, various carbonisation temperatures and H 2 O 2 treatments were tested. For low sulfur content cokes, the aqueous oxidative treatment significantly increases the capacity values above 372 mAh/g during the first cycles. In contrast, cokes with a sulfur content of ca. 5%, did not shown a real improvement. The former results have been interpreted in terms of an effective oxidation of the particles surface, which removes unorganized carbon, where lithium can be irreversibly trapped. Moreover, a stable and less resistive passivating layer grows during the first discharge of lithium, as revealed by impedance spectroscopy. Therefore, chemical procedures, as mild oxidation, open an interesting field of research for the improvement of disordered carbons as anode materials in lithium ion batteries

  2. Study on the effect of heat treatment and gasification on the carbon structure of coal chars and metallurgical cokes using fourier transform Raman spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    S. Dong; P. Alvarez; N. Paterson; D.R. Dugwell; R. Kandiyoti [Imperial College London, London (United Kingdom). Department of Chemical Engineering

    2009-03-15

    Differences in the development of carbon structures between coal chars and metallurgical cokes during high-temperature reactions have been investigated using Raman spectroscopy. These are important to differentiate between different types of carbons in dust recovered from the top gas of the blast furnace. Coal chars have been prepared from a typical injectant coal under different heat-treatment conditions. These chars reflected the effect of peak temperature, residence time at peak temperature, heating rate and pressure on the evolution of their carbon structures. The independent effect of gasification on the development of the carbon structure of a representative coal char has also been studied. A similar investigation has also been carried out to study the effect of heat-treatment temperature (from 1300 to 2000{sup o}C) and gasification on the carbon structure of a typical metallurgical coke. Two Raman spectral parameters, the intensity ratio of the D band to the G band (I{sub D}/I{sub G}) and the intensity ratio of the valley between D and G bands to the G band (I{sub V}/I{sub G}), have been found useful in assessing changes in carbon structure. An increase in I{sub D}/I{sub G} indicates the growth of basic graphene structural units across the temperature range studied. A decrease in I{sub V}/I{sub G} appears to suggest the elimination of amorphous carbonaceous materials and ordering of the overall carbon structure. The Raman spectral differences observed between coal chars and metallurgical cokes are considered to result from the difference in the time-temperature history between the raw injectant coal and the metallurgical coke and may lay the basis for differentiation between metallurgical coke fines and coal char residues present in the dust carried over the top of the blast furnace. 41 refs., 17 figs., 3 tabs.

  3. Features of hydrotreating catalytic cracking feed and heavy slow coking gas oils

    Energy Technology Data Exchange (ETDEWEB)

    Yefremov, N.I.; Kushnarev, D.F.; Frolov, P.A.; Chagovets, A.N.; Kalabin, G.A.

    1993-12-31

    A possible means of more extensive processing of crude oil is the use, in catalytic cracking, of heavy coking gas oils (HCGOs), a feature of which is a higher content of polycyclic aromatic compounds and resins by comparison with straight-run vacuum distillates. The presence of these compounds in catalytic cracking feed causes a reduction in the product yield and increased coke formation. Therefore, one of the problems of hydrotreating feedstock of this kind is the hydrogenation of polycyclic arenes. Processes of extensive desulphurization and denitration occur in parallel, since the sulphur and nitrogen compounds of HCGO are chiefly condensed benzoderivatives of thiophene, pyridine and carbazole, and largely concentrated in heavy aromatic and resinous fractions. The composition of the saturated part of the cracking feed plays a large role in achieving the optimum yields of gaseous and gasoline fractions. Thus an increase in the proportion of cyclanes in the feed raises the gasoline yield. In this way, an investigation of the hydrocarbon conversions during the hydrotreatment of cracking feed is of great importance. The present paper sets out the results for studying the change in the group-structural characteristics of the hydrogenation products of a mixture containing 30% HCGOs according to data of {sup 1}H and {sup 13}C NMR spectroscopy. 7 refs., 7 figs., 1 tab.

  4. Coke formation during the hydrotreatment of bio-oil using NiMo and CoMo catalysts

    NARCIS (Netherlands)

    Kadarwati, Sri; Hu, Xun; Gunawan, Richard; Westerhof, Roel; Gholizadeh, Mortaza; Hasan, M. D.Mahmudul; Li, Chun-Zhu

    2017-01-01

    This study aims to investigate the coke formation during the hydrotreatment of bio-oil at low temperature. The catalytic hydrotreatment of bio-oil produced from the pyrolysis of mallee wood was carried out using pre-sulphided NiMo and CoMo catalysts at a temperature range of 150–300 °C. Our results

  5. Development of a facility for the recovery of high-purity hydrogen from coke oven gas by pressure swing adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, M; Saida, K; Uenoyama, K; Sugishita, M; Imokawa, K

    1985-01-01

    This paper reports 1) a pressure swing adsorption (PSA) system comprising three towers, each packed with three different adsorbents; and 2) studies of the application of this system to the recovery of high-purity hydrogen from coke oven gas. Running the adsorption plant at 35 C and 9.5 kg/cm/sup 2/ gives optimum operating stability and economy. In addition, an optimum time cycle for the three-tower system has been developed. Gas from the PSA equipment proper still contains traces of oxygen. This is removed in a further tower packed with Pd catalyst. The ultimate recovery of hydrogen is closely related to its concentration in the raw coke oven gas and to the degree of purity attained. 3 references.

  6. Environmentally Persistent Free Radicals in Soils of Past Coking Sites: Distribution and Stabilization.

    Science.gov (United States)

    Jia, Hanzhong; Zhao, Song; Nulaji, Gulimire; Tao, Kelin; Wang, Fu; Sharma, Virender K; Wang, Chuanyi

    2017-06-06

    This study presents the existence of environmentally persistent free radicals (EPFRs) in soils of past coking sites, mainly contaminated by polycyclic aromatic hydrocarbons (PAHs). Measurements of EPFRs were conducted by electron paramagnetic resonance (EPR) technique with numerous soil samples, which were collected from different distances (0-1000 m) and different depths (0-30 cm) of three contaminant sources. EPR signals with ∼3 × 10 17 radicals/g of the soil samples were obtained, which are very similar to that generated in PAHs contaminated clays, that is, g = 2.0028-2.0036. Concentrations of PAHs and soil components were determined to understand their role in producing EPFRs. PAHs, clay, and iron predominately contributed to generating EPRFs. Meanwhile, organic matter negatively influenced the production of EPRFs. The effects of environmental factors (moisture and oxic/anoxic) were also studied to probe the persistency of EPFRs under various simulated conditions. The EPFRs are stable under relatively dry and oxic conditions. Under anoxic conditions without O 2 and H 2 O, the spin densities decrease initially, followed by gradual increase before attaining constant values in two months period time. The present work implies that continuous formation of EPFRs induced by PAHs is largely responsible for the presence of relatively stable radicals in soils of coking sites.

  7. Simulation and optimization of a coking wastewater biological treatment process by activated sludge models (ASM).

    Science.gov (United States)

    Wu, Xiaohui; Yang, Yang; Wu, Gaoming; Mao, Juan; Zhou, Tao

    2016-01-01

    Applications of activated sludge models (ASM) in simulating industrial biological wastewater treatment plants (WWTPs) are still difficult due to refractory and complex components in influents as well as diversity in activated sludges. In this study, an ASM3 modeling study was conducted to simulate and optimize a practical coking wastewater treatment plant (CWTP). First, respirometric characterizations of the coking wastewater and CWTP biomasses were conducted to determine the specific kinetic and stoichiometric model parameters for the consecutive aeration-anoxic-aeration (O-A/O) biological process. All ASM3 parameters have been further estimated and calibrated, through cross validation by the model dynamic simulation procedure. Consequently, an ASM3 model was successfully established to accurately simulate the CWTP performances in removing COD and NH4-N. An optimized CWTP operation condition could be proposed reducing the operation cost from 6.2 to 5.5 €/m(3) wastewater. This study is expected to provide a useful reference for mathematic simulations of practical industrial WWTPs. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Study on treatment of coking wastewater by biofilm reactors combined with zero-valent iron process

    International Nuclear Information System (INIS)

    Lai Peng; Zhao Huazhang; Zeng Ming; Ni Jinren

    2009-01-01

    Experiments were conducted to investigate the behavior of the integrated system with biofilm reactors and zero-valent iron (ZVI) process for coking wastewater treatment. Particular attention was paid to the performance of the integrated system for removal of organic and inorganic nitrogen compounds. Maximal removal efficiencies of chemical oxygen demand (COD), ammonia nitrogen (NH 3 -N) and total inorganic nitrogen (TIN) were up to 96.1, 99.2 and 92.3%, respectively. Moreover, it was found that some phenolic compounds were effectively removed. The refractory organic compounds were primarily removed in ZVI process of the integrated system. These compounds, with molecular weights either ranged 10,000-30,000 Da or 0-2000 Da, were mainly the humic acid (HA) and hydrophilic (HyI) compounds. Oxidation-reduction and coagulation were the main removal mechanisms in ZVI process, which could enhance the biodegradability of the system effluent. Furthermore, the integrated system showed a rapid recovery performance against the sudden loading shock and remained high efficiencies for pollutants removal. Overall, the integrated system was proved feasible for coking wastewater treatment in practical applications

  9. Discrete Element Method Modeling of the Rheological Properties of Coke/Pitch Mixtures

    OpenAIRE

    Majidi, Behzad; Taghavi, Seyed Mohammad; Fafard, Mario; Ziegler, Donald P.; Alamdari, Houshang

    2016-01-01

    Rheological properties of pitch and pitch/coke mixtures at temperatures around 150 °C are of great interest for the carbon anode manufacturing process in the aluminum industry. In the present work, a cohesive viscoelastic contact model based on Burger’s model is developed using the discrete element method (DEM) on the YADE, the open-source DEM software. A dynamic shear rheometer (DSR) is used to measure the viscoelastic properties of pitch at 150 °C. The experimental data obtained is then use...

  10. Fractionation of trace elements and human health risk of submicron particulate matter (PM1) collected in the surroundings of coking plants.

    Science.gov (United States)

    Zajusz-Zubek, Elwira; Radko, Tomasz; Mainka, Anna

    2017-08-01

    Samples of PM1 were collected in the surroundings of coking plants located in southern Poland. Chemical fractionation provided information on the contents of trace elements As, Cd, Co, Cr, Hg, Mn, Ni, Pb, Sb and Se in all mobile (F1-F3) and not mobile (F4) fractions of PM1 in the vicinity of large sources of emissions related to energochemical processing of coal during the summer. The determined enrichment factors indicate the influence of anthropogenic sources on the concentration of the examined elements contained in PM1 in the areas subjected to investigation. The analysis of health risk for the assumed scenario of inhabitant exposure to the toxic effect of elements, based on the values of the hazard index, revealed that the absorption of the examined elements contained in the most mobile fractions of particulate matter via inhalation by children and adults can be considered potentially harmless to the health of people inhabiting the surroundings of coking plants during the summer (HI PM1, approximately four adults and one child out of one million people living in the vicinity of the coking plants may develop cancer.

  11. Hydrogen separation from coke oven gas using PSA

    Energy Technology Data Exchange (ETDEWEB)

    Takeuchi, M.: Tanibashi, N.; Nishida, S

    1983-01-01

    Twin column apparatus was used to study the adsorption characteristics of various components of coke oven gas at an adsorption pressure of 5 kg/cm/SUP/2G. The following results were obtained. Over 99.99% Of the H/sub 2/ could be separated, and for this a 5 angstrom zeolite was optimal. Since the break-through order is H/sub 2/, O/sub 2/, N/sub 2/, CH/SUB/4, CO there is a tendency for the product H/sub 2/ to be adulterated with O/sub 2/ and N/sub 2/. Although there was a large adsorption of CO/sub 2/ and C/sub 2/H/sub 4/, desorption was difficult, even under reduced pressure and H/sub 2/ flushing. Hence, the industrial version of this apparatus will have to include activated carbon. 5 references.

  12. Structural variations and physical properties of lignin coke

    International Nuclear Information System (INIS)

    Otani, C.

    1986-01-01

    The studied lignin is a by-product of the process of ethanol production from eucaliptus. It was heat-treated under inert atmosphere conditions at increasing temperatures from 300 0 C up to 2600 0 C. This material has about 35 weight % of carbon yield and low ash content (0.70 w %). The structural variations were studied by wide-angle X-ray diffraction, small-angle X-ray scattering and infra-red spectroscopy. The bulk and the ''real'' density of the samples have also been determined as a function of the heat treatment temperatures. These experimental results enabled us to establish a mechanism of structure variation based on the formation of a graphite-like and porous structure within the initially amorphous lignin matrix. It has been possible to specify the adequate heat treatment temperature based upon the lignin coke applications. (author) [pt

  13. On-line determination of moisture in coal and coke

    International Nuclear Information System (INIS)

    Cutmore, N.G.; Sowerby, B.D.

    1987-01-01

    The CSIRO Division of Mineral Engineering is developing various techniques for the on-line determination of moisture in coal and coke, and some instruments are now commercially available. These techniques permit accurate and rapid determination of moisture in materials directly on conveyor belts or in bins. The most promising techniques for direct on-belt measurement of moisture in coal are capacitance and microwave transmission. A non-contacting under-belt capacitance and gamma-ray backscatter technique has determined moisture in coal to better than 0.5 wt% in field tests. CSIRO is developing a fast neutron and gamma-ray transmission technique, which is proving very accurate in laboratory tests. This technique overcomes many of the limitations of thermal neutrons moisture gauges

  14. Biotransformation of nitrogen- and sulfur-containing pollutants during coking wastewater treatment: Correspondence of performance to microbial community functional structure.

    Science.gov (United States)

    Joshi, Dev Raj; Zhang, Yu; Gao, Yinxin; Liu, Yuan; Yang, Min

    2017-09-15

    Although coking wastewater is generally considered to contain high concentration of nitrogen- and sulfur-containing pollutants, the biotransformation processes of these compounds have not been well understood. Herein, a high throughput functional gene array (GeoChip 5.0) in combination with Illumina MiSeq sequencing of the 16S rRNA gene were used to identify microbial functional traits and their role in biotransformation of nitrogen- and sulfur-containing compounds in a bench-scale aerobic coking wastewater treatment system operated for 488 days. Biotransformation of nitrogen and sulfur-containing pollutants deteriorated when pH of the bioreactor was increased to >8.0, and the microbial community functional structure was significantly associated with pH (Mantels test, P functional microbial community structure (P functional genes for biotransformation of nitrogen- and sulfur-containing pollutants. Functional characterization of taxa and network analysis suggested that Burkholderiales, Actinomycetales, Rhizobiales, Pseudomonadales, and Hydrogenophiliales (Thiobacillus) were key functional taxa. Variance partitioning analysis showed that pH and influent ammonia nitrogen jointly explained 25.9% and 35.5% of variation in organic pollutant degrading genes and microbial community structure, respectively. This study revealed a linkage between microbial community functional structure and the likely biotransformation of nitrogen- and sulfur-containing pollutants, along with a suitable range of pH (7.0-7.5) for stability of the biological system treating coking wastewater. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Limitations of the removal of cyanide from coking wastewater by ozonation and by the hydrogen peroxide-ozone process.

    Science.gov (United States)

    Pueyo, N; Miguel, N; Ovelleiro, J L; Ormad, M P

    The purpose of this study is to compare the efficiency of ozonation and the hydrogen peroxide-ozone process for the removal of cyanide from coking wastewater. The most efficient oxidation process is combined with coagulation-flocculation-decantation and lime-soda ash softening pretreatments. The oxidation in aqueous solution and industrial wastewater (at pH 9.5-12.3) by O3 was carried out using a range of concentration of consumed O3 from 10 to 290 mg/L. A molar ratio of H2O2/O3 from 0.1 to 5.2 with different concentrations of O3 constants was used for the H2O2-O3 process. The maximum cyanide removal obtained in coking wastewater was 90% using a mass ratio of O3/CN(-) of 9.5. Using lower concentrations of O3, cyanide is not removed and can even be generated due to the presence of other cyanide precursor organic micropollutants in the industrial matrix. The concentration of O3 is reduced to half for the same cyanide removal efficiency if the pretreatments are applied to reduce the carbonate and bicarbonate ions. The cyanide removal efficiency in coking wastewater is not improved if the O3 is combined with the H2O2. However, the preliminary cyanide removal treatment in aqueous solution showed an increase in the cyanide removal efficiency for the H2O2-O3 process.

  16. Ammonium nitrogen removal from coking wastewater by chemical precipitation recycle technology.

    Science.gov (United States)

    Zhang, Tao; Ding, Lili; Ren, Hongqiang; Xiong, Xiang

    2009-12-01

    Ammonium nitrogen removal from wastewater has been of considerable concern for several decades. In the present research, we examined chemical precipitation recycle technology (CPRT) for ammonium nitrogen removal from coking wastewater. The pyrolysate resulting from magnesium ammonium phosphate (MAP) pyrogenation in sodium hydroxide (NaOH) solution was recycled for ammonium nitrogen removal from coking wastewater. The objective of this study was to investigate the conditions for MAP pyrogenation and to characterize of MAP pyrolysate for its feasibility in recycling. Furthermore, MAP pyrolysate was characterized by scanning electron microscope (FESEM), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FTIR) as well as X-ray diffraction (XRD). The MAP pyrolysate could be produced at the optimal condition of a hydroxyl (OH(-)) to ammonium molar ratio of 2:1, a heating temperature of 110 degrees C, and a heating time of 3h. Surface characterization analysis indicated that the main component of the pyrolysate was amorphous magnesium sodium phosphate (MgNaPO(4)). The pyrolysate could be recycled as a magnesium and phosphate source at an optimum pH of 9.5. When the recycle times were increased, the ammonium nitrogen removal ratio gradually decreased if the pyrolysate was used without supplementation. When the recycle times were increased, the ammonium nitrogen removal efficiency was not decreased if the added pyrolysate was supplemented with MgCl(2).6H(2)O plus Na(2)HPO(4).12H(2)O during treatment. A high ammonium nitrogen removal ratio was obtained by using pre-formed MAP as seeding material.

  17. [Advanced treatment of coking wastewater with a novel heterogeneous electro-Fenton technology].

    Science.gov (United States)

    Li, Hai-Tao; Li, Yu-Ping; Zhang, An-Yang; Cao, Hong-Bin; Li, Xin-Gang; Zhang, Yi

    2011-01-01

    A novel electro-catalytic reactor, with oxygen-reduction cathode (PAQ/GF), dimensionally stable anode (IrO2-RuO2 -TiO2/ Ti) and heterogeneous catalysts, is developed for advanced treatment of coking wastewater after biological process, integrating cathodic and anodic simultaneous oxidation processes. A PAQ/GF electrode was synthesized by the electro-polymerization of 2-ethyl anthraquinone on graphite felt, which was characterized with cyclic voltametry measurements; the results indicated that the PAQ/GF electrode showed high reversibility for oxidation-reduction reaction of anthraquinone and catalytic activity for O2 reduction to H2O2; 13.5 mmol/L H2O2 was obtained after electrolysis for 6 h at -0.7 V (vs. SCE) and pH 6 with a current efficiency of 50% in a membrane reactor. Fe-Cu/Y350 catalysts, prepared by impregnation method, could catalyze the production of hydroxyl radicals (*OH) from H2O2, which was confirmed both by fading reaction of crystal violet and oxidation of *OH-probe compound (p-chlorobenzoic acid); Fe-Cu/Y350 also showed high catalytic-activity for the oxidation of organics by hypochlorous sodium, because COD removal of coking wastewater reached 26% in the catalytic process while only 11% of COD removal was obtained in the absence of Fe-Cu/Y350. COD removal of coking wastewater reached 49.4% (26.0% and 23.4% in cathodic system and anodic system, respectively) in the developed electrolytic-reactor, which was higher than that of conventional cathodic-anodic-oxidation process (29.8%). At optimal reaction condition of initial COD = 192 mg/L, I = 10A x m(-2) and pH 4-5, more than 50% COD were removed after electrolysis for 1 h. The mechanism might be as follows: in cathodic system, H2O2 is generated from reduction of O2 on PAQ/GF cathode, and catalyzed by Fe-Cu/Y350 for production of *OH, which causes mineralization and degradation of organic pollutants; in anodic system, Cl2 and HClO are generated from Cl- oxidation on IrO2-RuO2-TiO2/Ti anode and the

  18. Regulatory impact analysis of national emissions standards for hazardous air pollutants for by-product coke oven charging, door leaks, and topside leaks. Draft report

    International Nuclear Information System (INIS)

    1992-11-01

    Under the authority of the 1990 Clean Air Act Amendments, a Natioal Emissions Standard for Hazardous Air Pollutants is proposed to control emissions from By-product Coke Oven Charging, door leaks, and topside leaks. Because the EPA considers the regulation for By-product Coke Oven batteries to be a major rule, the attached Regulatory Impact Analysis was prepared to fulfill the requirements of E012291. The document reviews the need for regulation, control techniques, regulatory options, costs of control, economic impacts, benefits of the regulation, and compares benefits and costs associated with the regulation

  19. In-Class Quantification of the Mentos and Diet Coke Analogue Experiment: Effects of Wind on Volcanic Isopach Patterns

    Science.gov (United States)

    Quane, S.; Klos, Z.; Jacobsen, R.

    2009-05-01

    The Mentos and Diet Coke experiment, where instantaneous emplacement of Mentos candy in Diet Coke creates a soda/CO2 eruptive plume, is a common educational analogue for a volcanic eruption. In this paper, we quantify the effects of varying directional wind speeds on the eruptive plume as a learning tool in advanced Introductory Geology and Volcanology courses. The Mentos and Diet Coke reaction is a fun, safe and affordable analogue for explosive, single pulse, basaltic eruptions (e.g., Strombolian eruptions). Specifically, the physical and chemical reaction nucleating CO2 bubbles on the pitted surface of Mentos candy is directly analogous to the collapsing foam eruption regime described by Parfitt (2004) where inertia driven fragmentation of the liquid (Namiki and Manga, 2008) leads to basaltic pyroclastic eruptions. Often, in these systems, the pyroclasts are carried downwind, resulting lopsided (downwind side taller) cinder cones. In our experiments, we create a single pulse eruption by simultaneously dropping four Mentos candies into a 16.9 oz. bottle of Diet Coke. The experiments are run under different wind conditions created by three stacked box fans in the off (control experiment) low, medium and high settings. Wind speed is measured using a hand held anemometer. The pyroclast dispersal is recorded by degree of liquid saturation through four layers of newspaper. The liquid is allowed to soak in for thirty seconds post eruption and then the individual layers of newspaper are separated and the saturation envelope is traced with a black marker and digitally photographed. The pyroclast dispersal envelope (or saturation area) is then quantified from the photos by image analysis in Adobe Photoshop. In addition, the experiments are videotaped to quantify ejection velocity using frame by frame analysis in iMovie. The resulting isopach ("deposit thickness") maps indicate a strong tightening of dispersal envelopes with increasing wind speed as seen in natural

  20. Fly ashes from coal and petroleum coke combustion: current and innovative potential applications.

    Science.gov (United States)

    González, Aixa; Navia, Rodrigo; Moreno, Natalia

    2009-12-01

    Coal fly ashes (CFA) are generated in large amounts worldwide. Current combustion technologies allow the burning of fuels with high sulfur content such as petroleum coke, generating non-CFA, such as petroleum coke fly ash (PCFA), mainly from fluidized bed combustion processes. The disposal of CFA and PCFA fly ashes can have severe impacts in the environment such as a potential groundwater contamination by the leaching of heavy metals and/or particulate matter emissions; making it necessary to treat or reuse them. At present CFA are utilized in several applications fields such as cement and concrete production, agriculture and soil stabilization. However, their reuse is restricted by the quality parameters of the end-product or requirements defined by the production process. Therefore, secondary material markets can use a limited amount of CFA, which implies the necessity of new markets for the unused CFA. Some potential future utilization options reviewed herein are zeolite synthesis and valuable metals extraction. In comparison to CFA, PCFA are characterized by a high Ca content, suggesting a possible use as neutralizers of acid wastewaters from mining operations, opening a new potential application area for PCFA that could solve contamination problems in emergent and mining countries such as Chile. However, this potential application may be limited by PCFA heavy metals leaching, mainly V and Ni, which are present in PCFA in high concentrations.

  1. Immobilization and encapsulation during vitrification of incineration ashes in a coke bed furnace

    International Nuclear Information System (INIS)

    Kuo, Y.-M.; Lin, T.-C.; Tsai, P.-J.

    2006-01-01

    A real-scale coke bed furnace system has been successfully applied to vitrify the incineration ashes into glassy slags. The object of this research was to evaluate the effect of the system on the immobilization of metal species in the slag. Ashes and slag specimens were tested to identify their metal phase distribution following a sequential extraction procedure. The mobility of Al, Ca, Cd, Cr, Mg, Mn and Pb was noticeably reduced by vitrification. An important implication is the reduction of Cr 6+ to Cr 3+ along with its immobilization with this coke bed furnace. The Ni and Zn contents were relatively low in slag, indicating that their availability of mobile phases in ashes was reduced during vitrification. The XRD analyses identified the major crystalline phase in slag as akermanite, which is inert and helpful in metal immobilization. The phase distribution analysis also contributed to verify that the incorporation of Ca and Mg enhanced the encapsulation in the slag matrix. The low oxygen content in slag made the structure of silicate resistant to the proton-promoted attack and also enhanced the mobility reduction of matrix elements (Ca, Mg and Al) in the moderately reducible phase and also contributed to the immobilization of other metal species. However, the properties of slag also deserve further studies to ensure its long-term stability and safety

  2. Steam cracking of hydrocarbons 6. Effect of dibenzyl sulfide and dibenzyl disulfide on reaction kinetics and coking

    NARCIS (Netherlands)

    Bajus, M.; Baxa, J.; Leclercq, P.A.; Rijks, J.A.

    1983-01-01

    The influence of aromatic sulfides on the kinetics and selectivity of hydrocarbon conversion by steam cracking and on pyrolytic coke formation was investigated in stainless steel tubular reactors with relatively large inner surface.The rate of decomposition of heptane (at 700 ‘C, 100 kPa, and a mass

  3. Effects of polymerization and briquetting parameters on the tensile strength of briquettes formed from coal coke and aniline-formaldehyde resin

    Energy Technology Data Exchange (ETDEWEB)

    Demirbas, A.; Simsek, T. [Selcuk University, Konya (Turkey)

    2006-10-15

    In this work, the utilization of aniline (C{sub 6}H{sub 7}N) formaldehyde (HCHO) resins as a binding agent of coke briquetting was investigated. Aniline (AN) formaldehyde (F) resins are a family of thermoplastics synthesized by condensing AN and F in an acid solution exhibiting high dielectric strength. The tensile strength sharply increases as the ratio of F to AN from 0.5 to 1.6, and it reaches the highest values between 1.6 and 2.2 F/AN ratio; it then slightly decreases. The highest tensile strength of F-AN resin-coke briquette (23.66 MN/m{sup 2}) was obtained from the run with 1.5 of F/AN ratio by using (NH4){sub 2}S{sub 2}O{sub 8} catalyst at 310 K briquetting temperature. The tensile strength of F-AN resin-coke briquette slightly decreased with increasing the catalyst percent to 0.10%, and then it sharply decreased to zero with increasing the catalyst percent to 0.2%. The effect of pH on the tensile strength is irregular. As the pH of the mixture increases from 9.0 to 9.2, the tensile strength shows a sharp increase, and the curve reaches a plateau value between pH 9.3 and 9.9; then the tensile strength shows a slight increase after pH = 9.9.

  4. Experimental investigation into the surface oxidation of lignite high temperature coke

    Energy Technology Data Exchange (ETDEWEB)

    Schaefer, H G; Dallmann, W [Technische Hochschule Aachen (Germany, F.R.). Lehrgebiet Kokerei und Brikettierung

    1979-11-01

    It was intended to produce lignite high temperature coke (BHFK) in the laboratory comparable to that produced with the Salem-Lurgi-open hearth process and quench them according to the prescribed condition. By this means, the surface oxide formation could be continually recorded gravimetrically. The self-sustaining reaction of the physical and chemical adsorption on the loose material were observed under consideration that the adsorption or surface oxide can exist in a gaseous as well as in a liquid aggregate. The established steam isotherms and electron-microscope photos identified the product BFHK as a material which shows in the range of high-humidity capillary condensation. The continuous gravimetric adsorption leads to 1,9 per cent by weight on dry surface oxides. On the other hand, oxidized coke in the presence of water builds up on the surface to 2,3 per cent by weight. It became apparent that the finest capillary water is not involved in the formation of the oxide. For the dry accumulation, which is a reaction of the first degree, the equation for the accumulation of the oxygen is given. From the BET surface, made up from the graphite-like ring structure of the carbon surface, as well as the dposited quantity of oxide, the surface density of the oxygen atoms is indicated in relation to the quantity of carbon atoms, or alternatively the six-ring. The dry deposition leads to a proportion of 1,5 oxygen atoms to 10 carbon atoms. In a wet reaction, the ratio is 1,8 to 10. With increasing quantities of oxide, the content of volatile matter, the sparking point and reactivity increase, while the porosity diminishes as a consequence.

  5. Proceedings of the Joint Meeting of The Fuel Society of Japan (1991). 28th Coal Science Conference/91st Coke Meeting; (Sha) nenryo kyokai godo taikai happyo ronbunshu (1991). Dai 28 kai sekitan kagaku kaigi dai 91 kai cokes tokubetsukai

    Energy Technology Data Exchange (ETDEWEB)

    1991-11-07

    Relating to coke, studies are made on the rapid coke production method, oven investigation during carbonization, and operational management/control. As to coal science, studies are mainly on the brown coal two-stage liquefaction (BCL) method, and data on the pilot plant and PSU are reported. Concerning bituminous coal liquefaction, PSU data mostly including the NEDOL process, and characteristics of liquefaction residue and its effective utilization by thermal decomposition are reported. Regarding the liquefaction mechanism, an experimentally extensive study on catalyst, solvent and reaction conditions is made using model materials and coal itself on the bench scale and also in the pilot plant. Engineering subjects on residue, solvent deashing, scale attachment and coprocessing are also reported. Relations of decomposition process to coal chemical structure changes and reaction conditions are investigated. As to coal gasification, studies, which are not many, are conducted on material balance, heat balance, and image characteristics of char for gasification and factors controlling reactivity.

  6. Emissions and emission reduction systems in the coal derivative production facilities of a coking plant. Emissionsquellen in Kohlenwertstoffbetrieben von Kokereien und Massnahmen zu ihrer Verminderung

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    Coking plants may present odour unisances to their vicinity although these odours are no health problem. Typical odorants emitted by a coking plant are: Hydrogen sulfide, mercaptanes, carbon sulfide, naphthaline, phenol and ammonia. The odour threshold of these substances may be quite close to the analytical detection limit. There are a large number of emission sources, e.g. production and storage containers, baths, tar sinks, and ventilation systems. The report describes the possible sources of emissions as well as the countermeasures available at the present state of the art.

  7. Discrete element method applied to the vibration process of coke particles

    OpenAIRE

    Majidi, Behzad

    2012-01-01

    Les propriétés physiques, mécaniques et chimiques des matières premières ont un effet majeur sur la qualité des anodes en carbone pour le procédé de production d’aluminium. Ce travail tente d’étudier la faisabilité de l’application de simulation de la Méthode des Élément Discrets (DEM) à la technologie de production d’anodes. L’effet de la forme des particules et de la distribution de leurs tailles sur la densité apparente vibrée (VBD) d’échantillons de coke sec est étudié. Les particules de ...

  8. Development of reduced crude processing technology in delayed coking units; Desenvolvimento da tecnologia de processamento de residuo atmosferico em unidade de coqueamento retardado

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Gloria Maria Gomes; Bartros, Francisco Carlos da Costa; Goncalves, Natalie Jorge; Pala, Danielle Marins; Nadolni, Aline Voigt [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    Delayed Coking Technology can be described as thermal cracking of low value refinery residual streams into high-value products. This process has been applied in petroleum refining schemes in order to upgrade heavy and ultra-heavy crude oils. The typical feedstock is vacuum residue (VR). When we have an increasing medium distillates demand and refining schemes which have gas oil and VR excess, the simultaneous conversion of these streams becomes economically attractive, due mainly to the increase of diesel production. Thus, the processing of atmospheric residue (AR) in Delayed Coking Units (DCU) has fueled great interest for PETROBRAS. This work presents the results of industrial and pilot plant tests with AR and VR showing the increasing of diesel yields and decreasing of coke yields processing AR as feedstock. When we process all the AR in the DCU with high recycle rate we observe an increasing of 25% on refinery diesel production related to conventional schemes. The refining scheme of the new PETROBRAS refinery at Northeast of Brazil is based on this technology. This refinery will process heavy oils maximizing diesel production with minimum investment. (author)

  9. A complex approach to the health states of pitch coking plant workers

    Energy Technology Data Exchange (ETDEWEB)

    Kandus, J.

    1976-01-01

    206 workers of three pitch coking plants, who had been exposed for an average of 4 years to fumes containing 3,4 benzopyrene, were examined. No occupational carcinoma or precancerous foci were detected. The only statistically significant findings were chronic atrophic inflammations of upper respiratory pathways (26%). This investigation is the initial stage in a long-term study of this group of workers. A plan for preventive examinations (including specialized ones), contraindications applicable for this type of job, methods for epidemiological investigations and the follow-up of workers after leaving this work, are described in detail.

  10. Synergistic effects and kinetics thermal behaviour of petroleum coke/biomass blends during H2O co-gasification

    International Nuclear Information System (INIS)

    Edreis, Elbager M.A.; Luo, Guangqian; Li, Aijun; Xu, Chaofen; Yao, Hong

    2014-01-01

    Highlights: • Sugar cane bagasse and blends gasification presented two stages at all H 2 O values. • Petroleum coke showed only one char gasification stage at (>700 °C) at 75% H 2 O. • Significant interactions are existed in the both reaction stages of samples. • Higher H 2 O concentration and PC content lead to higher kinetic parameter values. • All the models are successfully utilized to predict the experimental data. - Abstract: This study investigates the possible synergistic interactions between the Sudanese lower sulphur petroleum coke (PC) and sugar cane bagasse (SCB) during H 2 O co-gasification with three concentration values (25%, 50% and 75% v/v) using a thermogravimetric analyser (TGA) at 20 °C/min. The kinetic thermal behaviour, and effects of both H 2 O concentration and fuel blending ratio were investigated. The results show that, significant interactions existed in both reaction stages of samples, and become less when PC content and H 2 O concentration are 50%. Petroleum coke showed only one char gasification stage at (>700 °C) at 75% H 2 O. Some kinetics models like homogeneous and shrinking core models were studied by the Coats–Redfern method in order to observe the optimum reaction mechanism for the H 2 O gasification of samples, describe the best reactive behaviour and determine the kinetic parameters. The results showed that, the co-gasification behaviour and kinetic parameters have a significantly influenced by increasing both H 2 O concentration and PC content. The boundary controlled reaction model (R2) shows the lowest values of activation energy (E) for all samples and H 2 O concentrations. Finally, all the models are successfully utilized to predict the experimental data under all H 2 O concentration values

  11. 75 FR 53963 - Notice of Baseline Filings: The Peoples Gas Light and Coke Company, Minnesota Energy Resources...

    Science.gov (United States)

    2010-09-02

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PR10-86-000, Docket No. PR10-87-000, Docket No. PR10-88- 000, Docket No. PR10-89-000, Docket No. PR10-90-000] Notice of Baseline Filings: The Peoples Gas Light and Coke Company, Minnesota Energy Resources Corporation, Louisville Gas...

  12. Estimation of quality and yields of products from the process of future national oils indelayed coking units; Estimativa da qualidade e dos rendimentos de produtos de coqueamento a partir do processamento de petroleos nacionais

    Energy Technology Data Exchange (ETDEWEB)

    Filipakis, Sofia D.; Silva, Maria do Socorro A.J. da; Guimaraes, Regina C.L. [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2008-07-01

    As the importance of the delayed coking process increases in the Brazilian refinery scenario, it is necessary to perform a more detailed evaluation of vacuum residues potential on this kind of process. This work compares the performance of future produced and exported oils residues with those which are references nowadays as delayed coking feeding. This information is essential for the prediction of the future quality and yield of the products generated by this process, and for the determination of the oils value for exportation. For this purpose, a process simulator was used considering the operational conditions of a real delayed coking unit. The carbon residue and asphaltenes ratio from the residues were also evaluated. This simulation demonstrated that most of the future oils will produce a high quality coke from the point of view of crystallinity and metals content, and it will present high contents of both volatile matter and sulphur. The exported oils residues are likely to show good crystallinity. (author)

  13. Impact of Zr metal and coking reactions on the ex-vessel source term predictions of CORCON/VANESA

    International Nuclear Information System (INIS)

    Lee, M.; Davis, R.E.; Khatib-Rahbar, M.

    1987-01-01

    During a core meltdown accident in a LWR, molten core materials (corium) could leave the reactor vessel and interact with concrete. In this paper, the impact of the zirconium content of the corium pool and the coking reaction on the release of fission products are quantified using CORCON/Mod2 and VANESA computer codes. Detailed calculations show that the total aerosol generation is proportional to the zirconium content of the corium pool. Among the twelve fission product groups treated by the VANESA code, CsI, Cs 2 O and Nb 2 O 5 are completely released over the course of the core/concrete interaction, while an insignificant quantity of Mo, Ru and ZrO 2 are predicted to be released. The release of BaO, SrO and Ce 2 O increase, while the releases of Te and La 2 O 3 are relatively unaffected by the Zr content of the corium pool. The impact of the coking reaction on the radionuclide release and aerosol production was found to be insignificant

  14. Deciphering Cyanide-Degrading Potential of Bacterial Community Associated with the Coking Wastewater Treatment Plant with a Novel Draft Genome.

    Science.gov (United States)

    Wang, Zhiping; Liu, Lili; Guo, Feng; Zhang, Tong

    2015-10-01

    Biotreatment processes fed with coking wastewater often encounter insufficient removal of pollutants, such as ammonia, phenols, and polycyclic aromatic hydrocarbons (PAHs), especially for cyanides. However, only a limited number of bacterial species in pure cultures have been confirmed to metabolize cyanides, which hinders the improvement of these processes. In this study, a microbial community of activated sludge enriched in a coking wastewater treatment plant was analyzed using 454 pyrosequencing and Illumina sequencing to characterize the potential cyanide-degrading bacteria. According to the classification of these pyro-tags, targeting V3/V4 regions of 16S rRNA gene, half of them were assigned to the family Xanthomonadaceae, implying that Xanthomonadaceae bacteria are well-adapted to coking wastewater. A nearly complete draft genome of the dominant bacterium was reconstructed from metagenome of this community to explore cyanide metabolism based on analysis of the genome. The assembled 16S rRNA gene from this draft genome showed that this bacterium was a novel species of Thermomonas within Xanthomonadaceae, which was further verified by comparative genomics. The annotation using KEGG and Pfam identified genes related to cyanide metabolism, including genes responsible for the iron-harvesting system, cyanide-insensitive terminal oxidase, cyanide hydrolase/nitrilase, and thiosulfate:cyanide transferase. Phylogenetic analysis showed that these genes had homologs in previously identified genomes of bacteria within Xanthomonadaceae and even presented similar gene cassettes, thus implying an inherent cyanide-decomposing potential. The findings of this study expand our knowledge about the bacterial degradation of cyanide compounds and will be helpful in the remediation of cyanides contamination.

  15. Experimental Study of Advanced Treatment of Coking Wastewater Using MBR-RO Combined Process

    Science.gov (United States)

    Zhang, Lei; Hwang, Jiannyang; Leng, Ting; Xue, Gaifeng; Chang, Hongbing

    A membrane bioreactor-reverse osmosis (MBR-RO) combined process was used for advanced treatment of coking wastewater from secondary biological treatment. MBR and RO units' treatment efficiency for the pollution removal were conducted, and effects of raw water conductivity and trans-membrane pressure on water yield and desalination rate in RO unit were investigated in detail. The experimental results proved that MBR-RO combined process ran steadily with good treatment effect, which could obtain stable effluent water quality and met the requirement of "Design Criterion of the Industrial Circulating Cooling Water Treatment" (GB 50050-2007).

  16. Fate and wetting potential of bio-refractory organics in membrane distillation for coke wastewater treatment.

    Science.gov (United States)

    Ren, Jing; Li, Jianfeng; Chen, Zuliang; Cheng, Fangqin

    2018-06-02

    Membrane distillation (MD) has been hindered in industrial applications due to the potential wetting or fouling caused by complicated organic compositions. This study investigated the correlations between the fate and wetting potential of bio-refractory organics in the MD process, where three coke wastewater samples pre-treated with bio-degradation and coagulation served as feed solutions. Results showed that although most of the bio-refractory organics in coke wastewater were rejected by the hydrophobic membrane, some volatile aromatic organics including benzenes, phenols, quinolines and naphthalenes passed through the membrane during the MD process. Interestingly, membrane wetting occurred coincidently with the penetration of phenolic and heterocyclic organics. The wetting rate was obviously correlated with the feed composition and membrane surface properties. Ultimately, novel insights into the anti-wetting strategy of MD with bio-refractory organics was proposed, illustrating that the polyaluminum chloride/polyacrylamide coagulation not only removed contaminants which could accelerate membrane wetting, but also retarded membrane wetting by the complexation with organics. The deposition of these complexes on the membrane surface introduced a secondary hydrophilic layer on the hydrophobic substrate, which established a composite membrane structure with superior wetting resistance. These new findings would be beneficial to wetting control in membrane distillation for wastewater treatment. Copyright © 2018 Elsevier Ltd. All rights reserved.

  17. Concentration of carcinoembryonic antigen alpha-fetoprotein and beta-subunit of human chorionic gonadotropin in the serum of coke oven workers

    Energy Technology Data Exchange (ETDEWEB)

    Snit, M. [Silesian Medical Academy, Zabrze (Poland)

    1993-01-01

    Increased levels of carcinoembryonic antigen and {alpha}-fetoprotein were found in blood serum of coke oven workers, and also to some extent in smokers and in residents of industrial cities. The {beta} subunit of chorionic gonadotropin was barely detectable.

  18. The determination of sulfur and some heavy elements in the coke

    International Nuclear Information System (INIS)

    Ma'rouf, M.

    2003-01-01

    The content of free sulfur and some heavy elements in the coke resulting from the residua of oil industry was determined bu using various technical analytical methods. The flame technique of atomic absorption FAAS was used to identify lead, copper, zinc, chromium, VGA-AAS and determine arsenic and selenium, CV-AAS to the determination of mercury. As for sulfur, it was determined by using the total oxidation method at high temperatures (1100 C 0 ). The IR indicator was used for further determination. The relative standard deviation in the determination of sulfur did not exceed the limits of 0.01 and 0.02, compared to the determination of other elements by using the atomic absorption method. (Author)

  19. The Grilled Effect of Particle's Distribution of Calsine Coke's at 900oC Temperature upon the Electric Resistivity, Hardness and CompressiveStrength Analysis

    International Nuclear Information System (INIS)

    NS, Kasilani; D, Imam; Dwi-Herwidhi

    2000-01-01

    Investigation of Calsine Coke's particle's distribution by grilledtreatment at 900 o C temperature upon the electric resistivity, hardness andcompressive strength analysis had been done. The Calsine Coke's were crushedand sieved to get a particle size about 63; 90; 106 μm, then mixed thevariety size particle with 33 % tar pitch 125 μm, be heated, shaped andpressed to be pellet. The pellets were grilled at 900 o C temperature during30 minutes and then these were analyzed. The whole analysis using 2-b mixedwas the best, particle ratio were 63:106 = 1:2 and pointed the electricresistivity 2.63 Ωm, the hardness 5.9 kg/mm 2 and the compressivestrength 1600 N. (author)

  20. Synergetic effects leading to coke-resistant NiCo bimetallic catalysts for dry reforming of methane

    KAUST Repository

    Li, Lidong

    2015-01-08

    A new dry reforming of methane catalyst comprised of NiCo bimetallic nanoparticles and a Mgx(Al)O support that exhibits high coke resistance and long-term on-stream stability is reported. The structural characterization by XRD, TEM, temperature-programmed reduction, and BET analysis demonstrates that the excellent performance of this catalyst is ascribed to the synergy of various parameters, including metal-nanoparticle size, metal-support interaction, catalyst structure, ensemble size, and alloy effects.

  1. Effects of Coke Deposits on the Catalytic Performance of Large Zeolite H-ZSM-5 Crystals during Alcohol-to-Hydrocarbons Reactions as Investigated by a Combination of Optical Spectroscopy and Microscopy

    DEFF Research Database (Denmark)

    Nordvang, Emily Catherine; Borodina, Elena; Ruiz-Martínez, Javier

    2015-01-01

    The catalytic activity of large zeolite H-ZSM-5 crystals in methanol (MTO) and ethanol-to-olefins (ETO) conversions was investigated and, using operando UV/Vis measurements, the catalytic activity and deactivation was correlated with the formation of coke. These findings were related to in situ...... single crystal UV/Vis and confocal fluorescence micro-spectroscopy, allowing the observation of the spatiotemporal formation of intermediates and coke species during the MTO and ETO conversions. It was observed that rapid deactivation at elevated temperatures was due to the fast formation of aromatics...... at the periphery of the H-ZSM-5 crystals, which are transformed into more poly-aromatic coke species at the external surface, preventing the diffusion of reactants and products into and out of the H-ZSM-5 crystal. Furthermore, we were able to correlate the operando UV/Vis spectroscopy results observed during...

  2. Production of metallurgical cokes from some Turkish lignites using sulphite liquor binders

    Energy Technology Data Exchange (ETDEWEB)

    Yanik, J.; Saglam, M.; Yuksel, M. (Ege University, Izmir (Turkey). Dept. of Chemistry)

    1990-04-01

    Soma and Tuncbilek lignites were briquetted at 80{degree}C under 0-100 MPa, using varying amounts of sulphite liquor binders. The briquettes were then carbonized at 950{degree}C, and the resulting formed cokes were examined. The effects of the type and concentration of binders, and of the briquetting pressure, on the strength and porosity of the formcokes were investigated. As a result of these experiments, optimal briquetting conditions were established. It was also stated that formcokes made from both Turkish lignite samples under optimal briquetting conditions could be used for metallurgical purposes, particularly in non-ferrous metallurgy. 17 refs., 1 fig., 4 tabs.

  3. Eight-term cyclic phosphites as coke deposit inhibitors and a method for producing them

    Energy Technology Data Exchange (ETDEWEB)

    Vershinin, P.V.; Chebotareva, E.G.; Kadyrova, V.Kh.; Kirpichnikov, P.A.; Pozdnev, V.V.; Vershinin, Yu.P.; Zharkova, V.M.

    1982-01-01

    It is proposed that a eight-term cyclic phosphite formula be used where R = methyl, R' = tertiary-butyl or alpha-methylcyclohexyl, R'' = tertiary-butyl, R''' = hydrogen, methyl, tertiary-butyle, bromine, X = methylene and sulfur as coke deposit inhibitors in the pyrolysis of petroleum raw materials. A method for producing the eight-term cyclic phosphite formula is proposed where a cyclic chlorophosphite formula interacts with a phenol formula in a medium of polar aprotic solvent using a base at 80-100 degrees.

  4. Isotopic ratio based source apportionment of children's blood lead around coking plant area.

    Science.gov (United States)

    Cao, Suzhen; Duan, Xiaoli; Zhao, Xiuge; Wang, Beibei; Ma, Jin; Fan, Delong; Sun, Chengye; He, Bin; Wei, Fusheng; Jiang, Guibin

    2014-12-01

    Lead exposure in the environment is a major hazard affecting human health, particularly for children. The blood lead levels in the local children living around the largest coking area in China were measured, and the source of blood lead and the main pathways of lead exposure were investigated based on lead isotopic ratios ((207)Pb/(206)Pb and (208)Pb/(206)Pb) in blood and in a variety of media, including food, airborne particulate matter, soil, dust and drinking water. The children's blood lead level was 5.25 (1.59 to 34.36 as range) μg dL(-1), lower than the threshold in the current criteria of China defined by the US Centers for Disease Control (10 μg dL(-1)). The isotopic ratios in the blood were 2.111±0.018 for (208)Pb/(206)Pb and 0.864±0.005 for (207)Pb/(206)Pb, similar to those of vegetables, wheat, drinking water, airborne particulate matter, but different from those of vehicle emission and soil/dust, suggesting that the formers were the main pathway of lead exposure among the children. The exposure pathway analysis based on the isotopic ratios and the human health risk assessment showed that dietary intake of food and drinking water contributed 93.67% of total exposed lead. The study further indicated that the coal used in the coking plant is the dominant pollution source of lead in children's blood. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Environmental impact of heavy metals on the soils and plants around a coke-making factory of Jiyuan city, China

    Science.gov (United States)

    Lun Leung, Kwun

    2010-05-01

    The combustion of coal usually leads to many different kinds of pollution around coke-making factories. Among these pollutions, the heavy metal contamination in the soil and plants is one of the major concerns by people living around. Heavy metals are highly attracted to the biological tissue, and can stay in bodies of organisms for long period of time, causing a lot of hazardous diseases to human beings, animal and plants. In the developing regions of China, developing of industries has been based on the sacrifices of environments and human health. In order to evaluate the danger of heavy metal contamination from a coke factory to citizens of close inhabitants, a survey on soil and plants was conducted in the region around a coke-making factory in Jiyuan city, which is a major electricity supplying city for the Henan Province in China. In this study, 8 surface soil samples and 11 plant samples were collected from 8 different places around the coke-making factory in Jiyuan city. The collected samples are then treated in the laboratory, and 8 types of heavy metals, which include arsenic, cadmium, chromium, cobalt, copper, lead, nickel and zinc, are analyzed by Inductively Coupled Plasma Mass Spectrometry (ICP-MS) and Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES). The concentration data of heavy metals that collected from the analysis are then used to evaluate their toxicity towards living organisms and ecology by applying several biological effect standards, such as effect-range low (ERL), effect-range median (ERM) and several maximum allowances standards of heavy metal concentrations in soils and plants that established by different countries. Moreover, the relationship between the distance from the factory and the concentration of heavy metals in soils and plants are also evaluated in order to find out the contamination ranges of those heavy metals from the source. The result shows that the concentration of these 8 types of heavy metals in the

  6. Multimedia fate and source apportionment of polycyclic aromatic hydrocarbons in a coking industry city in Northern China

    International Nuclear Information System (INIS)

    Wang, Y.L.; Xia, Z.H.; Liu, D.; Qiu, W.X.; Duan, X.L.; Wang, R.; Liu, W.J.; Zhang, Y.H.; Wang, D.; Tao, S.; Liu, W.X.

    2013-01-01

    A steady state Level III fate model was established and applied to quantify source–receptor relationship in a coking industry city in Northern China. The local emission inventory of PAHs, as the model input, was acquired based on energy consumption and emission factors. The model estimations were validated by measured data and indicated remarkable variations in the paired isomeric ratios. When a rectification factor, based on the receptor-to-source ratio, was calculated by the fate model, the quantitatively verified molecular diagnostic ratios provided reasonable results of local PAH emission sources. Due to the local ban and measures on small scale coking activities implemented from the beginning of 2004, the model calculations indicated that the local emission amount of PAHs in 2009 decreased considerably compared to that in 2003. -- Highlights: •A steady-state fate model could well elucidate the multimedia fate of PAHs. •A rectification factor for correcting the paired isomeric ratio was calculated. •The corrected isomeric ratios were successfully applied to source apportionment. -- Based on multimedia model correction, the specific isomeric ratios could provide reasonable apportionments for the local PAHs emission sources

  7. Quality-oriented production of brown-coal coke with due regard to its application in metallurgy and environmental protection; Qualitaetsgerechte Erzeugung von Braunkohlenkoks unter Beruecksichtigung der Anwendung in Metallurgie und Umweltschutz

    Energy Technology Data Exchange (ETDEWEB)

    Achtelik, M.; Erken, M.; Juessen, P.; Knapp, A. [Rheinbraun AG, Koeln (Germany)

    1998-12-31

    In the nineteen seventies the Fortuna Nord refining factory of Rheinbraun AG began to restructure its operations from domestic coal briquetting to the manufacture of industrial products. One of these products, high-temperature brown-coal coke, is produced in two hearth-type furnaces. Coke produced in these plants is mainly used in metallurgy and environmental engineering, in the latter especially for flue gas purification. Rheinbraun has succeeded in introducing a quality management system for brown-coal coke which ensures high quality and security of supply. (orig.) [Deutsch] Im Veredlungsbetrieb Fabrik Fortuna-Nord der Rheinbraun AG begann in den 70er Jahren der Strukturwandel vom Hausbrandbrikett zu Industrieprodukten. Eins dieser Produkte, der Hochtemperatur-Braunkohlenkoks, wird in zwei Herdofenanlagen erzeugt. Die Haupteinsatzbereiche des Herdofenkokses sind die Metallurgie sowie der Umweltschutz und hier insbesondere die Rauchgasreinigung. Um die hohe Produktqualitaet und die Liefersicherheit zu gewaehrleisten, hat Rheinbraun ein Qualitaetsmanagementsystem fuer Braunkohlenkoks erfolgreich eingefuehrt. (orig.)

  8. Influence of carbonization conditions on the development of different types of optical anisotropy in cokes

    Energy Technology Data Exchange (ETDEWEB)

    Patrick, J W; Reynolds, M J; Shaw, F H

    1975-01-01

    The vitrain components of a series of coal samples were carbonized at temperatures from 400 to 1000/sup 0/C at different rates of heating ranging from 0.5 to 10/sup 0/K/min and utilizing soaking times up to 24 hr. Polished specimens prepared from the carbonized products were examined microscopically under polarized light in order to determine the proportions of the various types of optical anisotropy present in them. The variations in heating rate and soaking time were found to exert little significant influence on the anisotropy developed in high-temperature cokes. But in semicokes produced at carbonization temperatures within the plastic range the influence of the carbonization conditions was much more pronounced with the effects being interrelated. Decreasing the heating rate or increasing the soaking time led to the optical anisotropy generally becoming detectable at lower carbonization temperatures. Fast heating rates caused an increase in the rate of transformation of the fine-grain mosaic anisotropy into coarser-grained types of anisotropy and increased soaking time led to enhanced anisotropic development in the semicokes produced at temperatures within the plastic range. The type of anisotropy developed in cokes is closely related to the release of volatile matter and the plasticity developed during carbonization and the conclusion is drawn that the balance between these factors controls the extent of the anisotropic development.

  9. Effect of the exposure time in coke making atmosphere on the microstructure and properties of a refractory castable used in the petrochemical industry; Efeito do tempo de exposicao a uma atmosfera coqueificante na microestrutura e nas propriedades de um concreto refratario usado na industria petroquimica

    Energy Technology Data Exchange (ETDEWEB)

    Cabrelon, M.D.; Pereira, A.H.A.; Rodrigues, J.A., E-mail: marcelodezena@gmail.com [Grupo de Engenharia de Microestrutura de Materiais - GEMM, Departamento de Engenharia de Materiais - DEMa, Universidade Federal de S. Carlos - UFSCar, Sao Carlos, SP (Brazil); Medeiros, J. [CENPES, Petroleo Brasileiro S/A - PETROBRAS, Rio de Janeiro, RJ (Brazil); Toledo-Filho, R.D. [Laboratorio de Estruturas e Materiais - LABEST, COPPE, UFRJ, Rio de Janeiro, RJ (Brazil)

    2012-04-15

    Refractory castables used in Fluidized Catalytic Cracking Units (FCCU) are said to deteriorate due coke formation during the production of light hydrocarbons, causing a shortening in the operating time of the reactor. Consequently, a significant financial loss for the petrochemical will occur. Several studies have been carried out, but none of them showed clearly how much is the contribution of the coke for the concrete final deterioration. It still remains the doubt if the coke is the responsible for the damage observed macroscopically in a FCCU's riser. In this way, this work aimed to study the effect of the time in a coke making atmosphere on an anti-erosive class-C refractory castable, seeking for microstructural changes or on physical properties that indicate degradation mechanisms and give support to the understanding of the phenomenon. Samples of an industrial refractory castable used in petrochemical units were prepared and subjected to a forced coke making process in a simulation reactor. The temperature and the heating rate were kept constant at 540 deg C and 50 deg C/h, respectively. The values of 10, 60, 120, 240 and 480 h were used for the time of exposition to the propene gas. The microstructure of the samples was characterized through optical and scanning electron microscopy and its mineralogical phases through X-ray diffraction. Complementary analyses were necessary to a better understanding of the phenomenon. The results show that the surface and the microstructure are gradually impregnated by coke, which fills up pores, microcracks and cracks. Evidences of microcracking around the coke filled pores were not found. However, many aggregates present some type of deterioration related to the time of exposition to propene. Those damages are not necessarily caused by coke directly (author)

  10. Effect of the exposure time in coke making atmosphere on the microstructure and properties of a refractory castable used in the petrochemical industry; Efeito do tempo de exposicao a uma atmosfera coqueificante na microestrutura e nas propriedades de um concreto refratario usado na industria petroquimica

    Energy Technology Data Exchange (ETDEWEB)

    Cabrelon, M. D.; Pereira, A. H.A.; Rodrigues, J.A., E-mail: marcelodezena@gmail.com [Grupo de Engenharia de Microestrutura de Materiais - GEMM, Departamento de Engenharia de Materiais - DEMa, Universidade Federal de S. Carlos - UFSCar, Sao Carlos, SP (Brazil); Medeiros, J. [CENPES, Petroleo Brasileiro S/A - PETROBRAS, Rio de Janeiro, RJ (Brazil); Toledo-Filho, R. D. [Laboratorio de Estruturas e Materiais - LABEST, COPPE, UFRJ, Rio de Janeiro, RJ (Brazil)

    2012-04-15

    Refractory castables used in Fluidized Catalytic Cracking Units (FCCU) are said to deteriorate due coke formation during the production of light hydrocarbons, causing a shortening in the operating time of the reactor. Consequently, a significant financial loss for the petrochemical will occur. Several studies have been carried out, but none of them showed clearly how much is the contribution of the coke for the concrete final deterioration. It still remains the doubt if the coke is the responsible for the damage observed macroscopically in a FCCU's riser. In this way, this work aimed to study the effect of the time in a coke making atmosphere on an anti-erosive class-C refractory castable, seeking for microstructural changes or on physical properties that indicate degradation mechanisms and give support to the understanding of the phenomenon. Samples of an industrial refractory castable used in petrochemical units were prepared and subjected to a forced coke making process in a simulation reactor. The temperature and the heating rate were kept constant at 540 deg C and 50 deg C/h, respectively. The values of 10, 60, 120, 240 and 480 h were used for the time of exposition to the propene gas. The microstructure of the samples was characterized through optical and scanning electron microscopy and its mineralogical phases through X-ray diffraction. Complementary analyses were necessary to a better understanding of the phenomenon. The results show that the surface and the microstructure are gradually impregnated by coke, which fills up pores, microcracks and cracks. Evidences of microcracking around the coke filled pores were not found. However, many aggregates present some type of deterioration related to the time of exposition to propene. Those damages are not necessarily caused by coke directly (author)

  11. Evaluation of pitches and cokes from solvent-extracted coal materials

    Energy Technology Data Exchange (ETDEWEB)

    McHenry, E.R.

    1996-12-01

    Three initial coal-extracted (C-E) samples were received from the West Virginia University (WVU) Chemical Engineering Department. Two samples had been hydrogenated to obtain pitches that satisfy Theological requirements. One of the hydrogenated (HC-E) samples had been extracted by toluene to remove ash and higher molecular weight aromatic compounds. We were unable to measure the softening point and viscosity of the non-hydro treated solid extract sample, Positive characteristics in the HC-E materials were softening points of 113-119{degrees}C, low sulfur and ash. The oxygen and nitrogen content of the HC-E samples may limit future usage in premium carbon and graphite products. Coking values were similar to petroleum pitches. Laboratory anode testing indicates that in combination with standard coal-tar pitch, the HC-E material can be used as a binder pitch.

  12. A kinetic rate expression for the time-dependent coke formation rate during propane dehydrogenation over a platinum alumina monolithic catalyst

    NARCIS (Netherlands)

    Sint Annaland, van M.; Kuipers, J.A.M.; van Swaaij, W.P.M.

    2001-01-01

    Coke formation rates under propane dehydrogenation reaction conditions on a used monolithic Pt/¿-Al2O3 catalyst have been experimentally determined in a thermogravimetric analyser (TGA) as a function of time on stream covering wide temperature and concentration ranges. For relatively short times on

  13. A kinetic rate expression for the time-dependent coke formation rate during propane dehydrogenation over a platinum alumina monolithic catalyst.

    NARCIS (Netherlands)

    van Sint Annaland, M.; Kuipers, J.A.M.; van Swaaij, Willibrordus Petrus Maria

    2001-01-01

    Coke formation rates under propane dehydrogenation reaction conditions on a used monolithic Pt/y-Al2O3 catalyst have been experimentally determined in a thermogravimetric analyser (TGA) as a function of time on stream covering wide temperature and concentration ranges. For relatively short times on

  14. Emission and profile characteristic of volatile organic compounds emitted from coke production, iron smelt, heating station and power plant in Liaoning Province, China.

    Science.gov (United States)

    Shi, Jianwu; Deng, Hao; Bai, Zhipeng; Kong, Shaofei; Wang, Xiuyan; Hao, Jiming; Han, Xinyu; Ning, Ping

    2015-05-15

    107 kinds of C₂-C₁₂ volatile organic compound (VOC) mass concentrations and profiles for four types of coal-fired stationary sources in Liaoning Province were studied by a dilution sampling system and GC-MS analysis method, which are of significant importance with regard to VOC emissions in northeast of China. The results showed that there were some differences among these VOC source profiles. The total mass concentrations of analyzed 107 VOC species varied from 10,917 to 19,652 μg m(-3). Halogenated hydrocarbons exhibited higher mass percentages for the VOC source profiles of iron smelt (48.8%) and coke production plant (37.7%). Aromatic hydrocarbons were the most abundant in heating station plant (69.1%). Ketones, alcohols and acetates held 45.0% of total VOCs in thermal power plant. For non-methane hydrocarbons (NMHCs), which are demanded for photochemical assessment in the USA, toluene and n-hexane were the most abundant species in the iron smelt, coke production and thermal power plant, with the mass percentages of 64.8%, 52.7% and 38.6%, respectively. Trimethylbenzene, n-propylbenzene and o,m-ethyltoluene approximately accounted for 70.0% in heating station plant. NMHCs emitted from coke production, iron smelt, heating station and power plant listed above presented different chemical reactivities. The average OH loss rate of NMHCs from heating station, was 4 to 5.6 times higher than that of NMHCs from iron smelt, coke production and power plant, which implies that VOCs emitted from heating station in northeast of China should be controlled firstly to avoid photochemical ozone pollution and protect human health. There are significant variations in the ratios of benzene/toluene and m, p-xylene/ethylbenzene of these coal-fired source profiles. The representativeness of the coal-fired sources studied and the VOC samples collected should be more closely examined. The accuracy of VOC source profiles related to coal-fired processes is highly dependent on

  15. Effects of operating conditions on compositional characteristics and reaction kinetics of liquid derived by delayed coking of nigerian petroleum residue

    Directory of Open Access Journals (Sweden)

    O. O. Bello

    2006-09-01

    Full Text Available The thermal upgrading of Nigerian petroleum residue was studied at relatively low pressure in a delayed coking reactor system. In this work, the intent was to investigate the effects of process variables such as reaction temperature (200(0C to 600(0C, reaction time (0 to 120min, additive concentration loading and additive-to-residue ratio on the amounts and quality of organic liquid product (OLP. The liquid products derived from the delayed coking process were characterized by means of instrumental analysis of gas-liquid chromatography. Results obtained from the analyses of the OLP revealed an upward trend of the conversion process and the selectivity of the aromatic compounds with additive-to-residue ratio (ARR and increase in temperature. This led to maximum yield of 37.2% achieved with ARR of 5 compared to 31% achieved with ordinary thermal conversion. The selectivity for aromatic hydrocarbons was maximum at 83.1wt% the selectivity towards aromatics and aliphatic hydrocarbons were highest for methanol-potassium hydroxide and methanol respectively. In all additive system cases, maximum OLP was produced at an optimum reaction temperature of 370(0C in the delayed coking reactor and at higher residence time. The gaseous product consisted of carbon monoxide and carbon dioxide and C1 - C6 hydrocarbons, which amounted to about 20 to 30 wt% of liquid distillate. The information obtained in this study show that the organic liquid products are amenable to characterization procedure and provided the basis for the identification of processes for upgrading Nigerian petroleum residue and such other starting materials such as bitumen or fossil fuel coal liquids.

  16. Specific long non-coding RNAs response to occupational PAHs exposure in coke oven workers.

    Science.gov (United States)

    Gao, Chen; He, Zhini; Li, Jie; Li, Xiao; Bai, Qing; Zhang, Zhengbao; Zhang, Xiao; Wang, Shan; Xiao, Xinhua; Wang, Fangping; Yan, Yan; Li, Daochuan; Chen, Liping; Zeng, Xiaowen; Xiao, Yongmei; Dong, Guanghui; Zheng, Yuxin; Wang, Qing; Chen, Wen

    2016-01-01

    To explore whether the alteration of lncRNA expression is correlated with polycyclic aromatic hydrocarbons (PAHs) exposure and DNA damage, we examined PAHs external and internal exposure, DNA damage and lncRNAs (HOTAIR, MALAT1, TUG1 and GAS5) expression in peripheral blood lymphocytes (PBLCs) of 150 male coke oven workers and 60 non-PAHs exposure workers. We found the expression of HOTAIR, MALAT1, and TUG1 were enhanced in PBLCs of coke oven workers and positively correlated with the levels of external PAHs exposure (adjusted P trend  TUG1). However, only HOTAIR and MALAT1 were significantly associated with the level of internal PAHs exposure (urinary 1-hydroxypyrene) with adjusted β  = 0.298, P  = 0.024 for HOTAIR and β  = 0.090, P  = 0.034 for MALAT1. In addition, the degree of DNA damage was positively associated with MALAT1 and HOTAIR expression in PBLCs of all subjects (adjusted β  = 0.024, P  = 0.002 for HOTAIR and β  = 0.007, P  = 0.003 for MALAT1). Moreover, we revealed that the global histone 3 lysine 27 trimethylation (H3K27me3) modification was positively associated with the degree of genetic damage ( β  = 0.061, P  < 0.001) and the increase of HOTAIR expression ( β  = 0.385, P  = 0.018). Taken together, our findings suggest that altered HOTAIR and MALAT1 expression might be involved in response to PAHs-induced DNA damage.

  17. Co, Fe and Ni catalysts supported on coke for direct coal liquefaction

    International Nuclear Information System (INIS)

    Jimenez, Jose A; Villalba, Oscar A; Rodriguez, Luis I; Hernandez, Orlando; Agamez, Yasmin Y; Dias Jose de Jesus

    2008-01-01

    Transition metal catalysts supported on coke were prepared by impregnation with a solution of complex of metal-thiourea, that is produced from salt precursors of cobalt chloride, Nickel chloride or iron sulfate and ammonium. sulphide formation on the support surface was generated by decomposition of the metal complex. The catalysts obtained were used in direct coal liquefaction of a medium volatile bituminous coal (Yerbabuena N 1) from Cundinamarca using a 250 Ml, Parr reactor at 723 K and a hydrogen-donor solvent. The catalytic results show, for all samples, both a good coal conversion and an enhancement of the yield of oils, this indicates that the proposed preparation method of catalyst is effective and that eventually the H 2 S sulphidation conventional process could be replaced

  18. Study on the technology of decreasing ash and sulfur in coking coal concentrate by deep-cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Li, A.; Li, P.; Chen, S. [Hefei Design and Research Institute of Coal Industry, Hefei (China)

    2007-06-15

    Middling fractions of coking coal, a rare resource in China, were analysed for their embedded minerals both in kind and distribution. Observation with a microscope shows that most are clay minerals of very small particle size. The embedded minerals can be liberated from middling by grinding. Clean coal can be obtained from ground middling by the flocculation-flotation process. The yield of clean coal could thus be increased and its ash and sulfur content decreased. 3 refs., 2 figs., 4 tabs.

  19. Hydrogen and energy recovery by gasification of petroleum coke from heavy crude refining; Recuperacion de hidrogeno y energia mediante gasificacion de coques de petroleo provenientes de refinacion de crudos pesados

    Energy Technology Data Exchange (ETDEWEB)

    Paniagua-Rodriguez, J.C [Universidad Michoacana de San Nicolas de Hidalgo, Morelia, Michoacan (Mexico); Jimenez-Garcia, G. [Instituto Tecnologico del Valle de Morelia, Morelia, Michoacan (Mexico); Maya-Yescas, R. [Universidad Michoacana de San Nicolas de Hidalgo, Morelia, Michoacan (Mexico)]. E-mail: rmayay@umich.mx

    2013-03-15

    Heavy oils exhibit high yields to bottom-of barrel products (low commercial value); depending on the metals content and on carbon residue the upgrading of bottoms could follow either hydroprocessing or carbon rejection. In particular the Mexican Maya, which is the most refined crude in Mexico, is upgraded by carbon rejection via delayed coking of vacuum residue. In order to obtain acceptable economic profit, it is necessary to transform that carbon (mainly petroleum coke) into useful higher added value products. Coke gasification could be used to obtain hydrogen and/or energy (preferable electrical), via the reaction of coke molecules with oxygen, carbon dioxide and water. Departing from the empiric formulas of five petroleum cokes, a kinetic scheme that consists of three linearly independent stoichiometric equations was recently developed; by including the enthalpy of each reaction and considering the gasification reactor as adiabatic, it is possible to predict product stream composition and high pressure steam that could be generated by the process. [Spanish] Los crudos pesados exhiben rendimientos altos a productos de-fondo-de-barril (de bajo valor comercial); dependiendo del contenido de metales y del residuo carbonoso, la mejora de fondos puede llevarse a cabo por hidrotratamiento o rechazo de carbon. En particular el crudo Maya, que es el mas refinado en Mexico, se mejora via rechazo de carbon por coquizacion retardada del residuo de vacio. A fin de obtener ganancias aceptables, es necesario transformar ese carbon (coque de petroleo, principalmente) en producto util de alto valor agregado. La gasificacion de coque puede usarse para obtener hidrogeno y/o energia (electrica de preferencia), via la reaccion de moleculas de coque con oxigeno, dioxido de carbono y agua. Recientemente se desarrollo un esquema cinetico que consiste de tres reacciones linealmente independientes, partiendo de las formulas empiricas de cinco coques de petroleo; incluyendo la entalpia

  20. Study of the sulfur mechanism on the formation of coke deposition on iron surfaces; Etude des mecanismes d'action du soufre sur le cokage catalytique du fer

    Energy Technology Data Exchange (ETDEWEB)

    Bonnet, F.

    2001-12-01

    The formation of coke deposition which occurs in a range of temperature 500 deg C-650 deg C is a major problem in many chemical and petrochemical processes where hydrocarbons or other strongly carburizing atmospheres are involved. To reduce the rate of coke deposition, sulfur can be added in the gas phase. The topic of this work is to study the sulfur mechanism on the formation of coke deposition on iron surfaces. Firstly, we study the mechanism of graphitic filament formation on reduced and oxidised iron surfaces. A new mechanism of catalytic particle formation is proposed when the surface is initially oxidised. This mechanism is based on thermodynamic, kinetic and structural considerations. The results show that oxide/carbide transitions are involved in the transformation of the oxide layer in catalytic particles. Although the different iron oxides are precursors for the formation of catalytic particles, wustite (FeO) has a better reactivity than magnetite (Fe{sub 3}O{sub 4}) and hematite (Fe{sub 2}O{sub 3}). Sulfur acts on different steps of the coke formation, preventing phase transformations (carburation, graphitization) which occur during the formation of catalytic particles. Sulfur activity required to prevent these transformations changes with the temperature, the chemical state of iron (reduced or oxidised) and the carbon activity in the gas phase. Sulfur/ethylene co-adsorption studies were performed on mono-crystal of iron (110). The results show that sulfur can prevent adsorption and decomposition of this hydrocarbon on metallic surface (Fe) and on magnetite (Fe{sub 3}O{sub 4}). Then, sulfur prevents the reaction leading to the carburation and graphitization of the surface. (author)