WorldWideScience

Sample records for cohesive fine powders

  1. Fluidization of fine powders cohesive versus dynamical aggregation

    CERN Document Server

    Valverde Millán, José Manuel

    2012-01-01

    This book illustrates the rich phenomenology exhibited by fine powders when fluidized by a gas flow, describing novel processes to assist fluidization by helping the gas flow to mobilize and break cohesive aggregates, which help to homogenize fluidization.

  2. Effect of compaction history on the fluidization behavior of fine cohesive powders.

    Science.gov (United States)

    Valverde, Jose Manuel; Castellanos, Antonio

    2006-05-01

    Fine particles agglomerate in the fluidized state due to the strength of interparticle attractive forces as compared to particle weight. Interparticle adhesion can be largely increased by consolidation stresses applied during powder handling. As a consequence, fragments of the consolidated powder may persist when the powder is fluidized, which gives rise to large agglomerates of strongly adhered particles in fluidization. This history-dependent effect can be minimized by coating the particles with surface additives such as silica nanoparticles. In this paper, we investigate the effect of high consolidation stresses sigma(c) previously applied to samples of silica-coated fine particles on their fluidization behavior. Our experimental measurements show that, even though homogeneous fluidization is still observed, the average agglomerate size and fractal dimension of the agglomerates increase as sigma(c) is increased. Bed expansion in the fluidized state is hindered by previously applied high consolidations, which we attribute to an increase of the largest stable size of mesoscopic fluid pockets. As a consequence, we observe that the initiation of macroscopic bubbling is delayed up to larger values of the fluid velocity.

  3. Extrinsic lactose fines improve dry powder inhaler formulation performance of a cohesive batch of budesonide via agglomerate formation and consequential co-deposition.

    Science.gov (United States)

    Kinnunen, Hanne; Hebbink, Gerald; Peters, Harry; Huck, Deborah; Makein, Lisa; Price, Robert

    2015-01-15

    The aim of the study was to investigate how the fine particle content of lactose carriers prepared with different types of lactose fines regulates dry powder inhaler (DPI) formulation performance of a cohesive batch of micronised budesonide. Budesonide formulations (0.8 wt%) were prepared with three different lactose carriers (Lactohale (LH) LH100, 20 wt% LH210 in LH100 and 20 wt% LH300 in LH100). Fine particle fraction of emitted dose (FPFED) and mean mass aerodynamic diameter (MMAD) of budesonide was assessed with a Next Generation Impactor (NGI) using a Cyclohaler at 90 l/min. Morphological and chemical characteristics of particles deposited on Stage 2 were determined using a Malvern Morphologi G3-ID. The results indicate that increasing concentration of lactose fines (lactose particles were available the more agglomerates of budesonide and lactose were delivered to Stage 2. These results suggest drug-fines agglomerate formation is an important mechanism for how lactose fines improve and regulate DPI formulation performance.

  4. Stress, strain, and bulk microstructure in a cohesive powder

    NARCIS (Netherlands)

    Andersson, R.; Bouwman, W.G.; Luding, S.; Schepper, de I.M.

    2008-01-01

    Spin-echo small-angle neutron scattering is able to characterize powders in terms of their density-density correlation function. Here we present a microstructural study on a fine cohesive powder undergoing uniaxial compression. As a function of compression, we measure the autocorrelation function of

  5. Granulation of fine powder

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ching-Fong

    2016-08-09

    A mixture of fine powder including thorium oxide was converted to granulated powder by forming a first-green-body and heat treating the first-green-body at a high temperature to strengthen the first-green-body followed by granulation by crushing or milling the heat-treated first-green-body. The granulated powder was achieved by screening through a combination of sieves to achieve the desired granule size distribution. The granulated powder relies on the thermal bonding to maintain its shape and structure. The granulated powder contains no organic binder and can be stored in a radioactive or other extreme environment. The granulated powder was pressed and sintered to form a dense compact with a higher density and more uniform pore size distribution.

  6. Measuring powder flowability with a modified Warren Spring cohesion tester

    Institute of Scientific and Technical Information of China (English)

    Salam A. Mohammed; Ezzat C. Abdullah; Derek Geldart; Abdul Aziz A. Raman

    2011-01-01

    The measurement of powder fiowability is a major concern for most industrial processes that deal with the handling of bulk solids as raw materials, intermediates, or products. The development of devices that measure the flowability of non-aerated powders has not progressed as rapidly as might have been hoped since most research activities have been based on various types of shear testers intended to aid the design of hoppers. A new flowability indicator named as weighted cohesion (WS) is established using newly improved version of direct cohesion texture. A cornerstone of the proposed technique is that the procedure is automated, using a digital Warren Spring tester called Warren Spring-University of Malaya cohesion tester (WSUMCT), thus making results operator-insensitive. Besides being a practical tool to diagnose the cohesion of experimental powders, the ratio between measured cohesion (using WSUMCT) and aerated density (using Hosokawa PT-S) provides us with a powerful technique to research fundamental particle internal cohesion forces directly and use these data to indicate the flowability. In this work, a series of fine (9.4 .μm) and coarse (60 μm) porous silica gel particle mixtures, and mixtures of fine (28 μm) and coarse (72 μm) glass ballotini as well, were used as test powders. The results from these tests agree well with relative flowability determined on our newly driven indicator using WSUMCT. The validation of aerated weighted cohesion (WSA) as a flowability indicator was authenticated by comparing the conducted parameter with established measured Hausner ratio (HR) and angle of repose (AoR).

  7. Magnetofluidization of fine magnetite powder.

    Science.gov (United States)

    Valverde, J M; Espin, M J; Quintanilla, M A S; Castellanos, A

    2009-03-01

    The behavior of a fluidized bed of fine magnetite particles as affected by a cross-flow magnetic field is investigated. A distinct feature of this naturally cohesive powder, as compared to noncohesive magnetic grains usually employed in magnetofluidized beds, is that the fluidized bed displays a range of stable fluidization even in the absence of an external magnetic field. Upon application of the magnetic field, the interval of stable fluidization is extended to higher gas velocities and bed expansion is enhanced. We have measured the tensile strength as affected by application of the external magnetic field according to two different operation modes. In the H off-on operation mode, the bed is driven to bubbling in the absence of external magnetic field. Once the gas velocity is decreased below the bubbling onset and the bed has returned to stable fluidization due to natural cohesive forces, the field is applied. In the H on-on mode, the field is maintained during the whole process of bubbling and return to stable fluidization. It is found that the tensile strength of the naturally stabilized bed is not essentially changed by application of the field ( H off-on) since the magnetic field cannot alter the bed structure once the particles are jammed in the stable fluidization state. Magnetic forces within the bulk of the jammed bed are partially canceled as a result of the anisotropic nature of the dipole-dipole interaction between the particles, which gives rise to just a small increment of the tensile strength. On the other hand, when the field is held on during bubbling and transition to stable fluidization ( H on-on mode), the tensile strength is appreciably increased. This suggests the formation of particle chains when the particles are not constrained due to the dipole-dipole attractive interaction which affects the mechanical strength of the stably fluidized bed. Experimental data are analyzed in the light of theoretical models on magnetic surface stresses.

  8. IMPROVEMENT OF FLUIDIZABILITY OF FINE POWDERS --A COMPUTER STUDY

    Institute of Scientific and Technical Information of China (English)

    R. Deiva Venkatesh; M. Grmela; Jamal Chaouki

    2005-01-01

    Simulations of the gas fluidization of a cohesive powder were performed using the Stokesian Dynamics method and an agglomeration-deagglomeration model to investigate methods of improving the fluidizability of fine powders. Three techniques (a) high gas velocity (b) vibration-assisted fluidization and (c) tapered fluidizer were used in the simulations which provided detailed information on the bed microscopy such as the motion of 100 particles in a fluidizing vessel along with the formation and destruction of cohesive bonds during collisions. While all three techniques were found to effectively improve the fluidizability of a strongly cohesive powder, we suggest a combination of high velocity fluidization assisted by external vibration of the fluidized bed to minimize entrainment of particles.

  9. Transport and deposition of cohesive pharmaceutical powders in human airway

    Science.gov (United States)

    Wang, Yuan; Chu, Kaiwei; Yu, Aibing

    2017-06-01

    Pharmaceutical powders used in inhalation therapy are in the size range of 1-5 microns and are usually cohesive. Understanding the cohesive behaviour of pharmaceutical powders during their transportation in human airway is significant in optimising aerosol drug delivery and targeting. In this study, the transport and deposition of cohesive pharmaceutical powders in a human airway model is simulated by a well-established numerical model which combines computational fluid dynamics (CFD) and discrete element method (DEM). The van der Waals force, as the dominant cohesive force, is simulated and its influence on particle transport and deposition behaviour is discussed. It is observed that even for dilute particle flow, the local particle concentration in the oral to trachea region can be high and particle aggregation happens due to the van der Waals force of attraction. It is concluded that the deposition mechanism for cohesive pharmaceutical powders, on one hand, is dominated by particle inertial impaction, as proven by previous studies; on the other hand, is significantly affected by particle aggregation induced by van der Waals force. To maximum respiratory drug delivery efficiency, efforts should be made to avoid pharmaceutical powder aggregation in human oral-to-trachea airway.

  10. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.

  11. Ultra fine tantalum powder for advanced capacitors

    Institute of Scientific and Technical Information of China (English)

    Nebera; A.; Markusbkin; Yu.; Azarov; V.; Ermolaev; N.

    2005-01-01

    Ultra fine tantalum and niobium powders are applicable in many areas of engineering. Of particular significance are high purity powders that are usable in production of high capacitance capacitors and superconductors.……

  12. Element test experiments and simulations: from dry towards cohesive powders

    NARCIS (Netherlands)

    Imole, O.I.; Kumar, N.; Luding, S.; Onate, E.; Owen, D.R.J.

    2011-01-01

    Findings from experiments and particle simulations for dry and cohesive granular materials are presented with the goal to reach quantitative agreement between simulations and experiments. Results for the compressibility, tested with the FT4 Powder Rheometer are presented. The first simulation result

  13. FLUIDIZATION OF FINE POWDERS IN FLUIDIZED BEDS WITH AN UPWARD OR A DOWNWARD AIR JET

    Institute of Scientific and Technical Information of China (English)

    Ruoyu Hong; Jianmin Ding; Hongzhong Li

    2005-01-01

    The hydrodynamic behavior of fine powders in jet-fluidized beds was studied numerically and experimentally. The starting point of numerical simulation was the generalized Navier-Stokes (N-S) equations for the gas and solids phases. The κ-εturbulence model was used for high-speed gas jets in fluidized beds. Computation shows that a suitable turbulence model is necessary to obtain agreement between the simulation and literature experimental data for a high-speed gas jet. The model was applied to simulating the fluidization of fine powders in fluidized beds with an upward or a downward air jet. An empirical cohesion model was obtained by correlating the cohesive force between fine particles using a cohetester. The cohesion model was embedded into the two-fluid model to simulate the fluidization of fine powders in two-dimensional (2-D) beds. To study the fluidization behavior of fine and cohesive powders with a downward jet,experiments were performed in a 2-D bed. Agreement between the computed time-averaged porosity and measured data was obtained. With an upward jet in the bed center, the measured and computed porosities show a dilute central core, especially at very high jet velocities. Based on our experiments and computations, a downward jet located inside the bed is recommended to achieve better mixing and contacting of gas and solids.

  14. A STUDY OF THE DISCHARGE OF COHESIVE POWDERS UNDER SIMULTANEOUS AERATION AND VIBRATION

    NARCIS (Netherlands)

    Marring, E.; Hoffmann, A.C; Janssen, L.P.B.M.

    1995-01-01

    The influence of applying simultaneous aeration and vibration on the discharge of cohesive powders from a laboratory scale cylindrical silo has been studied experimentally. The powders investigated were batches of potato starch powder of different moisture contents and therefore different degrees of

  15. Characterisation of flowability of cohesive powders by testing small quantities of weak compacts

    Institute of Scientific and Technical Information of China (English)

    Chuan Wang; Ali Hassanpour; Mojtaba Ghadiri

    2008-01-01

    Characterisation of flowability of small quantifies of cohesive powders is of great industrial interest, particularly for the pharmaceutical sec tors, where a limited amount of material is available or the material is not easily accessible. In this paper, ball indentation on a powder bed is evaluated for flow charaeterisation of small quantifies of cohesive powders at low levels of consolidation pressures. In parallel, the bulk powder is subjected to the common test method of unconfined direct compression. Analogous to indentation hardness testing, for which the indentation pressure is related to the flow stress, a constraint factor (C) is defined relating the unconfined yield stress and indentation pres sure. The constraint factors for the test powders have been evaluated, enabling an easy method to characterize the flow behaviour of cohesive powders.

  16. Warren-Spring based model for the shear yield locus of cohesive biomass powders

    Science.gov (United States)

    Vanneste-Ibarcq, Clément; Melkior, Thierry; de Ryck, Alain

    2017-06-01

    The objectives of this work are to determine accurately the cohesion of biomass powders from simple measures and to propose a new method for the description of the yield locus of powders with easy to measure parameters. The cohesion of 32 powders (wood, other biomasses and inorganic powders) have been analysed with two methods. The first method is the determination of the yield locus from shear tests at 3 kPa, performed with a powder rheometer, which gives an access to parameters such as cohesion (Y-intercept) and traction (X-intercept). The second method is the measurement of avalanche angles in a rotating drum. A linear relation is found between this angle and the cohesion length, ratio of the cohesion derived from the yield locus and the aerated density. Finally, a model is proposed for the prediction of the cohesion and the yield locus at 3 kPa, using only 2 parameters easy to measure: the avalanche angle and the aerated density.

  17. Evaluation of the Parameters Affecting the Cohesion of Fine Grained Soil

    Science.gov (United States)

    Vondráčková, Terezie; Kmec, Ján; Čejka, Jiří; Bartuška, Ladislav; Stopka, Ondrej

    2016-10-01

    Cohesion of the soils is one of the most important parameters which soil is evaluated in terms of its suitability for building foundations. Safety of construction is in fact dependent on the strength of soil, respectively shear strength. Fine-grained soil represents very specific group, in which is distinguished an effective and total cohesion of soils. The water in the soil thus drastically affects its cohesion contrary to gravel and sandy soils. The publication compares the tabular values of the effective and total cohesion and define the influence of water, grain size and consistency of her behaviour.

  18. Effect of milling temperatures on surface area, surface energy and cohesion of pharmaceutical powders.

    Science.gov (United States)

    Shah, Umang V; Wang, Zihua; Olusanmi, Dolapo; Narang, Ajit S; Hussain, Munir A; Tobyn, Michael J; Heng, Jerry Y Y

    2015-11-10

    Particle bulk and surface properties are influenced by the powder processing routes. This study demonstrates the effect of milling temperatures on the particle surface properties, particularly surface energy and surface area, and ultimately on powder cohesion. An active pharmaceutical ingredient (API) of industrial relevance (brivanib alaninate, BA) was used to demonstrate the effect of two different, but most commonly used milling temperatures (cryogenic vs. ambient). The surface energy of powders milled at both cryogenic and room temperatures increased with increasing milling cycles. The increase in surface energy could be related to the generation of surface amorphous regions. Cohesion for both cryogenic and room temperature milled powders was measured and found to increase with increasing milling cycles. For cryogenic milling, BA had a surface area ∼ 5× higher than the one obtained at room temperature. This was due to the brittle nature of this compound at cryogenic temperature. By decoupling average contributions of surface area and surface energy on cohesion by salinization post-milling, the average contribution of surface energy on cohesion for powders milled at room temperature was 83% and 55% at cryogenic temperature.

  19. Fine grain tungsten produced with nanoscale powder

    Institute of Scientific and Technical Information of China (English)

    Tao Lin; Fang Zhao; Liying Zhang; Chengyi Wu; Zhimeng Guo

    2005-01-01

    Nanoscale tungsten powder was prepared by reducing nanoscale tungsten trioxide in hydrogen to WO2.90 and further to W powder. After compacted with a rubber die, the nanoscale tungsten powder was sintered in a high-temperature dilatometer to investigate its shrinkage process. The results show that the compact of the nanoscale tungsten powder starts to shrink at 1050℃ and ends at 1500℃. The shrinkage rate reaches the maximum value at 1210℃. The relative density of sintered samples is 96.4%, and its grain size is about 5.8 μm.

  20. Process for preparing fine grain silicon carbide powder

    Science.gov (United States)

    Wei, G.C.

    Method of producing fine-grain silicon carbide powder comprises combining methyltrimethoxysilane with a solution of phenolic resin, acetone and water or sugar and water, gelling the resulting mixture, and then drying and heating the obtained gel.

  1. Aerated bunker discharge of fine dilating powders

    NARCIS (Netherlands)

    Ouwerkerk, C.E.D.; Molenaar, H.J.; Frank, M.J.W.

    1992-01-01

    The discharge rate of coarse powders (mean particle size 500 ¿m) from bunkers without aeration can be described by both empirical relations and theoretical models. In the case of small particles the discharge rate is largely overestimated. As the powder dilates during flow a negative pressure gradie

  2. Interparticle force based methodology for prediction of cohesive powder flow properties

    Science.gov (United States)

    Esayanur, Madhavan Sujatha Sarma

    The transport and handling of powders are key areas in the process industry that have a direct impact on the efficiency and/or the quality of the finished product. A lack of fundamental understanding of powder flow properties as a function of operating variables such as relative humidity, and particle size, leading to problems such as arching, rat-holing and segregation, is one the main causes for unscheduled down times in plant operation and loss of billions of dollars in revenues. Most of the current design strategies and characterization techniques for industrial powders are based on a continuum approach similar to the field of soil mechanics. Due to an increase in complexity of the synthesis process and reduction in size of powders to the nanoscale, the surface properties and inter particle forces play a significant role in determining the flow characteristics. The use of ensemble techniques such as direct shear testing to characterize powders are no longer adequate due to lack of understanding of the changes in the property of powders as a function of the major operating variables such as relative humidity, temperature etc. New instrumentation or techniques need to be developed to reliably characterize powder flow behavior. Simultaneously, scalability of the current models to predict powder flow needs to be revisited. Specifically, this study focuses on the development of an inter particle force based model for predicting the unconfined yield strength of cohesive powders. To understand the role of interparticle forces in determining the strength of cohesive powders, the particle scale interactions were characterized using Atomic Force Microscopy (AFM), contact angle, surface tension, and coefficient of friction. The bulk scale properties such as unconfined yield strength, packing structure, and size of the shear zone were also investigated. It was determined that an interparticle force based model incorporating the effect of particle size and packing structure

  3. Characterization of cohesive powders for bulk handling and DEM modelling

    NARCIS (Netherlands)

    Thakur, S.C.; Imole, Olukayode Isaiah; Wojtkowski, Mateusz Bronislaw; Magnanimo, Vanessa; Montes, E.C.; Ramaioli, Marco; Ahmadian, H.; Ooi, J.Y.; Bischoff, M.; Ramm, E.; Onate, E; Owen, R.; Wriggers, P.

    2013-01-01

    The flow behaviour of granular materials is relevant for many industrial applications including the pharmaceutical, chemical, consumer goods and food industries. A key issue is the accurate characterisation of these powders under different loading conditions and flow regimes, for example in mixers,

  4. Transverse flow of cohesive powders in rotating kilns: experimental study and modeling; Ecoulement transversal de poudres cohesives en four tournant: etude experimentale et modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Debacq, M.; Patisson, F.; Ablitzer, D. [Ecoles des Mines de Nancy, Lab. de Science et Genie des Materiaux Metalliques, UMR 7584, 54 - Nancy (France); Houzelot, J.L. [Ecole Nationale Superieure des Industries Chimiques (ENSIC), Lab. des Sciences du Genie Chimique, UPR 6811, 54 - Villers-les-Nancy (France); Feugier, A. [Societe Franco-Belge de Fabrication Combustibles, F.B.F.C., Dir. Technique, 26 - Romans (France); Hartmann, D. [Cogema, 26 - Pierrelatte (France)

    2001-07-01

    The transverse flow of cohesive powders of uranium in a rotating kiln equipped with raising levers has been studied experimentally at ambient temperature and at the temperatures of the process. The simple laws obtained have permitted to calculate the average distribution of the powder in a straight section of the kiln. (J.S.)

  5. Microwave-assisted hydrothermal synthesis of lead zirconate fine powders

    Directory of Open Access Journals (Sweden)

    Apinpus Rujiwatra

    2011-01-01

    Full Text Available A rapid synthesis of lead zirconate fine powders by microwave-assisted hydrothermal technique is reported. The influences of type of lead precursor, concentration of potassium hydroxide mineraliser, applied microwave power and irradiation time are described. The synthesised powders were characterised by powder X-ray diffraction, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopic microanalysis and light scattering technique. The merits of the microwave application in reducing reaction time and improving particle mono-dispersion and size uniformity as well as the drawbacks, viz. low purity of the desired phase and increasing demand of mineraliser, are discussed in relation to conventional heating method.

  6. Fluidized reduction of oxides on fine metal powders without sintering

    Science.gov (United States)

    Hayashi, T.

    1985-01-01

    In the process of reducing extremely fine metal particles (av. particle size or = 1000 angstroms) covered with an oxide layer, the metal particles are fluidized by a gas flow contg. H, heated, and reduced. The method uniformly and easily reduces surface oxide layers of the extremely fine metal particles without causing sintering. The metal particles are useful for magnetic recording materials, conductive paste, powder metallurgy materials, chem. reagents, and catalysts.

  7. Supercritical fluid molecular spray thin films and fine powders

    Science.gov (United States)

    Smith, Richard D.

    1988-01-01

    Solid films are deposited, or fine powders formed, by dissolving a solid material into a supercritical fluid solution at an elevated pressure and then rapidly expanding the solution through a short orifice into a region of relatively low pressure. This produces a molecular spray which is directed against a substrate to deposit a solid thin film thereon, or discharged into a collection chamber to collect a fine powder. The solvent is vaporized and pumped away. Solution pressure is varied to determine, together with flow rate, the rate of deposition and to control in part whether a film or powder is produced and the granularity of each. Solution temperature is varied in relation to formation of a two-phase system during expansion to control porosity of the film or powder. A wide variety of film textures and powder shapes are produced of both organic and inorganic compounds. Films are produced with regular textural feature dimensions of 1.0-2.0 .mu.m down to a range of 0.01 to 0.1 .mu.m. Powders are formed in very narrow size distributions, with average sizes in the range of 0.02 to 5 .mu.m.

  8. The effect of cohesive forces on the fluidization of aeratable powders

    Energy Technology Data Exchange (ETDEWEB)

    Galvin, Janine F.; Benyahia, Sofiane

    2014-01-01

    The effects of cohesive forces of van der Waals type in the fluidization/defluidization of aeratable type A powders in the Geldart classification are numerically investigated. The effects of friction and particle-size distribution (PSD) on some design-significant parameters, such as minimum fluidization and bubbling velocities, are also investigated. For these types of particles, cohesive forces are observed as necessary to fully exhibit the role friction plays in commonly observed phenomena, such as pressure overshoot and hysteresis around minimum fluidization. This study also shows that a full-experimental PSD consisting of a dozen particle sizes may be sufficiently represented by a few particle diameters. Reducing the number of particle types may benefit the continuum approach, which is based on the kinetic theory of granular flow, by reducing computational expense, while still maintaining the accuracy of the predictions.

  9. Production of Fine Metallic Powders by Hybrid Atomization Process

    Science.gov (United States)

    Minagawa, Kazumi; Liu, Yunzhong; Kakisawa, Hideki; Halada, Kohmei

    Hybrid Atomization is a recently developed powder-making process that combines effectively free-fall gas atomization and centrifugal atomization. This technique can produce very fine spherical powders with mean diameters of around 10 micrometers, and in high yields. The present report discusses the concept and basic principles of hybrid atomization. Process experiments were carried out and the optimal processing conditions were obtained. The results show that the influences of processing parameters and optimum conditions differ greatly between the proposed and the conventional atomization processes. A new correlation of atomization equation applicable to hybrid atomization is proposed and discussed.

  10. Process for preparing fine-grain metal carbide powder

    Science.gov (United States)

    Kennedy, C.R.; Jeffers, F.P.

    Fine-grain metal carbide powder suitable for use in the fabrication of heat resistant products is prepared by coating bituminous pitch on SiO/sub 2/ or Ta/sub 2/O/sub 5/ particles, heating the coated particles to convert the bituminous pitch to coke, and then heating the particles to a higher temperature to convert the particles to a carbide by reaction of said coke therewith.

  11. Production of fine powder from silk by radiation

    Energy Technology Data Exchange (ETDEWEB)

    Takeshita, Hidefumi; Yoshii, Fumio; Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Ishida, Kazushige; Kamiishi, Youichi [Textile Research Inst. of Gunma, Kiryu, Gunma (Japan)

    2000-09-01

    To produce silk fine powder, silk fibroin fibers were irradiated with an accelerated electron beam. Though unirradiated silk fibers were not pulverized at all, irradiated silk fibers were able to be crushed only by physical means using a ball mill. In the dose range of 250- 1000 kGy, as the dose to silk fibroin increased, the conversion rate from fiber to powder was increased. The electron microscope observation showed that the particle size of silk powder was less than 10 micrometers, and that those particles composed aggregate. Although silk fibroin fiber was not soluble in water, silk powders from fiber irradiated 500 kGy dissolved more than 50 weight %. Amino acid analysis of soluble fraction in silk powder showed that Gly content is lower than in normal silk and other amino acids contents except for Ala are 1.5 times as large as in normal silk. From these results, it is reasonable to suppose that irradiation and pulverization decomposed Gly and Ala. (author)

  12. Decoupling the contribution of dispersive and acid-base components of surface energy on the cohesion of pharmaceutical powders.

    Science.gov (United States)

    Shah, Umang V; Olusanmi, Dolapo; Narang, Ajit S; Hussain, Munir A; Tobyn, Michael J; Heng, Jerry Y Y

    2014-11-20

    This study reports an experimental approach to determine the contribution from two different components of surface energy on cohesion. A method to tailor the surface chemistry of mefenamic acid via silanization is established and the role of surface energy on cohesion is investigated. Silanization was used as a method to functionalize mefenamic acid surfaces with four different functional end groups resulting in an ascending order of the dispersive component of surface energy. Furthermore, four haloalkane functional end groups were grafted on to the surface of mefenamic acid, resulting in varying levels of acid-base component of surface energy, while maintaining constant dispersive component of surface energy. A proportional increase in cohesion was observed with increases in both dispersive as well as acid-base components of surface energy. Contributions from dispersive and acid-base surface energy on cohesion were determined using an iterative approach. Due to the contribution from acid-base surface energy, cohesion was found to increase ∼11.7× compared to the contribution from dispersive surface energy. Here, we provide an approach to deconvolute the contribution from two different components of surface energy on cohesion, which has the potential of predicting powder flow behavior and ultimately controlling powder cohesion.

  13. Investigation of the potential for direct compaction of a fine ibuprofen powder dry-coated with magnesium stearate.

    Science.gov (United States)

    Qu, Li; Zhou, Qi Tony; Gengenbach, Thomas; Denman, John A; Stewart, Peter J; Hapgood, Karen P; Gamlen, Michael; Morton, David A V

    2015-05-01

    Intensive dry powder coating (mechanofusion) with tablet lubricants has previously been shown to give substantial powder flow improvement. This study explores whether the mechanofusion of magnesium stearate (MgSt), on a fine drug powder can substantially improve flow, without preventing the powder from being directly compacted into tablets. A fine ibuprofen powder, which is both cohesive and possesses a low-melting point, was dry coated via mechanofusion with between 0.1% and 5% (w/w) MgSt. Traditional low-shear blending was also employed as a comparison. No significant difference in particle size or shape was measured following mechanofusion. For the low-shear blended powders, only marginal improvement in flowability was obtained. However, after mechanofusion, substantial improvements in the flow properties were demonstrated. Both XPS and ToF-SIMS demonstrated high degrees of a nano-scale coating coverage of MgSt on the particle surfaces from optimized mechanofusion. The study showed that robust tablets were produced from the selected mechanofused powders, at high-dose concentration and tablet tensile strength was further optimized via addition of a Polyvinylpyrrolidone (PVP) binder (10% w/w). The tablets with the mechanofused powder (with or without PVP) also exhibited significantly lower ejection stress than those made of the raw powder, demonstrating good lubrication. Surprisingly, the release rate of drug from the tablets made with the mechanofused powder was not retarded. This is the first study to demonstrate such a single-step dry coating of model drug with MgSt, with promising flow improvement, flow-aid and lubrication effects, tabletability and also non-inhibited dissolution rate.

  14. Production of fine powder from silk by radiation

    Energy Technology Data Exchange (ETDEWEB)

    Takeshita, Hidefumi; Yoshii, Fumio; Kume, Tamikazu [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment; Ishida, Kazunari; Kamiishi, Youichi [Textile Research Institute of Gunma, Kiryu, Gunma (Japan)

    2000-03-01

    Silk fine power was prepared directly from silk fiber irradiated with an accelerated electron beam(EB). Irradiated silk fiber was well pulverized only by physical crushing using ball mill without any chemical pretreatment. Raw and degummed silk fibers were irradiated at ambient temperature in the dose range of 250-1000 kGy. Although unirradiated silk fibers were not pulverized at all, irradiated fibers were easily pulverized and showed higher conversion from fiber to powder for higher doses. The presence of oxygen in the irradiation atmosphere enhanced pulverization of silk fiber. Raw silk fibers were less pulverized compared to degummed ones. The electron microscope observation showed that the minimum particle size of silk powder obtained from fiber irradiated by 1000 kGy in oxygen was less than 10 microns. It was found that fibroin powder obtained in this work dissolved remarkably into cold water, thought unirradiated fibroin fiber had little solubility even in hot water. A typical soluble fraction was about 60% for fibroin powder obtained from fiber irradiated by 1000 kGy in oxygen. (author)

  15. Synthesis of LiBOB Fine Powder to Increase Solubility

    Directory of Open Access Journals (Sweden)

    Etty Marti Wigayati

    2017-04-01

    Full Text Available Lithium bis (oxalate borate or LiBOB compound has captured interest of researchers, because it is potentially viable to be used as electrolyte salt in lithium-ion battery system. This compound is easy to synthesize and considered to be more environmentally friendly compared to conventional electrolyte salt because LiBOB does not contain halogen element. This research focused on the synthesis of LiBOB fine powder, which main purpose is improving LiBOB salt solubility in liquid electrolyte solution. This will aid the ion transfer between electrodes which in turn will increase the electrolyte performance. Solid state reaction was employed in this experiment. Synthesis of LiBOB compound was performed by reacting oxalic acid dihydrate, lithium hydroxide monohydrate, and boric acid. The resulting powder was then processed into fine powder using ball milling technique with varying milling time (0, 6, 10, and 13 hour. Microstructure of the sample was then analyzed to obtain information regarding phase formation, functional groups, grain surface morphology, surface area, pore volume, solubility, and ionic conductivity. The analysis shown that LiBOB and LiBOB hydrate phase was formed during the reaction, there was no changed in existing phase during milling process, crystallinity index was shifted to lower value but there was no difference in functional groups. Highest value in surface area was found to be 83.11 m2/g, with pore volume of 1.21311e+02 A at 10 hours milling. Smaller powder size resulted in higher solubility, unfortunately the ionic conductivity was found to be decreased.

  16. Optimization of calcium phosphate fine ceramic powders preparation

    Science.gov (United States)

    Sezanova, K.; Tepavitcharova, S.; Rabadjieva, D.; Gergulova, R.; Ilieva, R.

    2013-12-01

    The effect of biomimetic synthesis method, reaction medium and further precursor treatments on the chemical and phase composition, crystal size and morphology of calcium phosphates was examined. Nanosized calcium phosphate precursors were biomimetically precipitated by the method of continuous precipitation in three types of reaction media at pH 8: (i) SBF as an inorganic electrolyte system; (ii) organic (glycerine) modified SBF (volume ratio of 1:1); (iii) polymer (10 g/l xanthan gum or 10 g/l guar gum) modified SBF (volume ratio of 1:1). After maturation (24 h) the samples were lyophilized, calcinated at 300°C for 3 hours, and washed with water, followed by new gelation, lyophilization and step-wise (200, 400, 600, 800, and 1000°C, each for 3 hours) sintering. The reaction medium influenced the chemical composition and particle size but not the morphology of the calcium phosphate powders. In all studied cases bi-phase calcium phosphate fine powders with well-shaped spherical grains, consisting of β-tricalcium phosphate (β-TCP) and hydroxyapatite (HA) with a Ca/P ratio of 1.3 - 1.6 were obtained. The SBF modifiers decreased the particle size of the product in the sequence guar gum ˜ xanthan gum < glycerin < SBF medium.

  17. Spraying of Super Fine Powders With HVOF and Axial Plasma Thermal Spray Systems

    Institute of Scientific and Technical Information of China (English)

    Alan Burgess; G(o)tz Matth(a)us

    2004-01-01

    The use of fine powders in thermal spray can lead to many advantages. These advantages include denser coatings, coatings with increased wear resistance, coatings with smoother surface finish, coatings that can be applied to internal surfaces, less expensive coatings. The use of fine powders also has an disadvantage that th ey can have poor flow characteristics. The paper will discuss a feeder that is able to feed fine powders to overcome this difficulty and the coating equipment, both axial plasma and HVOF systems, used to deposit these materials to produce smooth dense coatings.

  18. Productions of ultra-fine powders and their use in high energetic compositions

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Yuri F.; Osmonoliev, Mirswan N.; Sedoi, Valentin S. [Institute of High Current Electronics RAS, 634055 Tomsk (Russian Federation); Arkhipov, Vladimir A.; Bondarchuk, Sergey S.; Vorozhtsov, Alexander B.; Korotkikh, Alexander G.; Kuznetsov, Valery T. [Tomsk State University, Lenin Ave., 36, Tomsk, 634034 (Russian Federation)

    2003-12-01

    Fine and ultra-fine powders are actively studied in pyrotechnics, explosives and propellants. The important questions are how to produce a powder with specified characteristics and how to use the powder produced. This paper presents an approach to the powder production by the exploding wire method. The influence of initial conditions on the properties of powders is discussed. The basic factors are as follows: the level and the uniformity of the energy, dissipated in the exploding wire metal; the density and the chemical activity of the surrounding gas; the initial radius of wire. Electron Microscopes (Transmission and Scanning) and the Surface BET Mehtod have been used for analyses. The production of ultra-fine powders based on such metals as Al, W, Zr, Cu, Fe, Ag, Co, In, Pt has been investigated. Different surrounding passive gases (nitrogen, argon, xenon, and helium) were used for producing powders of pure metals. Samples were studied by chemical methods. X-ray Diffraction and Electron Diffraction methods were used for the determination of the phase compositions. Characterization included also Differential Scanning Calorimetry and Thermogravimetry in air with a heating rate of 100 K/min. In summary, it was shown that the exploding wire method allows to produce ultra-fine powders of various metals. The results obtained can be applied directly to the production of powders with specified characteristics. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  19. Computer simulation of model cohesive powders: Plastic consolidation, structural changes, and elasticity under isotropic loads

    Science.gov (United States)

    Gilabert, F. A.; Roux, J.-N.; Castellanos, A.

    2008-09-01

    The quasistatic behavior of a simple two-dimensional model of a cohesive powder under isotropic loads is investigated by discrete element simulations. We ignore contact plasticity and focus on the effect of geometry and collective rearrangements on the material behavior. The loose packing states, as assembled and characterized in a previous numerical study [Gilabert, Roux, and Castellanos, Phys. Rev. E 75, 011303 (2007)], are observed, under growing confining pressure P , to undergo important structural changes, while solid fraction Φ irreversibly increases (typically, from 0.4-0.5 to 0.75-0.8). The system state goes through three stages, with different forms of the plastic consolidation curve, i.e., Φ as a function of the growing reduced pressure P*=Pa/F0 , defined with adhesion force F0 and grain diameter a . In the low-confinement regime (I), the system undergoes negligible plastic compaction, and its structure is influenced by the assembling process. In regime II the material state is independent of initial conditions, and the void ratio varies linearly with lnP [i.e., Δ(1/Φ)=λΔ(lnP*) ], as described in the engineering literature. Plasticity index λ is reduced in the presence of a small rolling resistance (RR). In the last stage of compaction (III), Φ approaches an asymptotic, maximum solid fraction Φmax , as a power law Φmax-Φ∝(P*)-α , with α≃1 , and properties of cohesionless granular packs are gradually retrieved. Under consolidation, while the range ξ of fractal density correlations decreases, force patterns reorganize from self-balanced clusters to force chains, with correlative evolutions of force distributions, and elastic moduli increase by a large amount. Plastic deformation events correspond to very small changes in the network topology, while the denser regions tend to move like rigid bodies. Elastic properties are dominated by the bending of thin junctions in loose systems. For growing RR those tend to form particle chains, the

  20. Five Recent Books on Super-fine Powders

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    @@ Professor Fengsheng Li of the Nanjing University of Science and Technology has been working in the field of superfine powders for many years, and at the turn of the century he started to write a series of monographs, now five, on the technology of superfine powders including their preparation, measurement and application, and ranging from catalysts through medicines and cosmetics to pyrotechnics.

  1. Improving Settling Dynamics of Activated Sludge by Adding Fine Talc Powder

    DEFF Research Database (Denmark)

    Rasmussen, Michael R.; Larsen, Torben; Clauss, F.

    1996-01-01

    . The settling velocity was measured with a recirculated settling column under different concentrations and turbulence levels. Numerical simulation of a secondary settling tank indicates that adding fine powder will improve the overall performance considerably.......The effect of adding varying mixtures of talc and chlorite powder to activated sludge in order to improve the settling characteristic has been studied. The powder is found to improve the settling velocity of the sludge, strictly by increasing the average density of the sludge floc aggregate...

  2. [Effect of mixing of fine carrier particles on dry powder inhalation property of salbutamol sulfate (SS)].

    Science.gov (United States)

    Iida, K; Leuenberger, H; Fueg, L M; Müller-Walz, R; Okamoto, H; Danjo, K

    2000-01-01

    The most commonly used formulations for dry powder inhalations are binary ordered mixes composed of micronized drugs and coarse carriers. An optimal dry powder aerosol formulation should possess an optimal inhalation property and a good flow property. These characteristics are especially important for a multidose dry powder inheler (DPI). In the present study, model powder blend were prepared consisting of synthesized sugar (different particle sized isomalt; IM-PF, IM-FS, IM-F) as a carrier and micronized salbutamol sulfate (SS). These ordered mixtures were aerosolized by the multidose JAGO DPI (SkyePharma AG) and in vitro deposition properties (fine particle fraction, FPF) were evaluated by a twin impinger (TI) at a flow rate of 60 l/min. The separation property between SS and carrier particles was investigated by the centrifuge method and air jet sieve (AJS) method. It was found that FPF decreased with increasing carrier particle size. However, a large carrier particle possesses a good flow property. Therefore, the effect of mixing of fine carrier particles (IM-PF) into the large carrier particles (IM-FS) on dry powder inhalation property was investigated. When the proportion of IM-PF (fine carrier) increase from 0% to 25% of the total carrier powder blend, the FPF also increases from 16.7% to 38.9%. It is concluded that the effect of mixing of fine carrier particles might be a suitable method for improving the dry powder inhalation properties.

  3. Effect of Fine Steel Slag Powder on the Early Hydration Process of Portland Cement

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Hydration heat evolution, non-evaporative water, setting time and SEM tests were performed to investigate the effect of fine steel slag powder on the hydration process of Portland cement and its mechanism.The results show that the effect of fine steel slag powder on the hydration process of Portland cement is closely related to its chemical composition, mineral phases, fineness, etc.Fine steel slag powder retards the hydration of portland cement at early age.The major reason for this phenomenon is the relative high content of MgO , MnO2, P2 O5in steel slag, and MgO solid solved in C3 S contained in steel slag.

  4. Magnetic properties of lanthanum orthoferrite fine powders prepared by different chemical routes

    Indian Academy of Sciences (India)

    Benedict Ita; P Murugavel; V Ponnambalam; A R Raju

    2003-10-01

    Fine powders of lanthanum iron oxide, LaFeO3, have been prepared by solid state reaction as well as sol-gel synthesis and nebulized spray pyrolysis. Structures, morphologies and magnetic susceptibility measurements of these powders have been examined. The powders prepared by all the three low-temperature routes contain nearly spherical particles with an average diameter of 40 nm. These samples show a lower Neel temperature than the powder prepared by solid state reaction besides showing much lower magnetic susceptibility at low temperatures.

  5. The effect of vibration on the fluidization behaviour of some cohesive powders

    NARCIS (Netherlands)

    Marring, E.; Hoffmann, A.C.; Janssen, L.P.B.M.

    1994-01-01

    One bed of glass ballotini and several beds of potato starch were fluidized with air at varying fluidization velocities, while the distributor plate was being vibrated at different amplitudes and frequencies to study the effect on the fluidization quality. The degree of cohesiveness of the potato st

  6. THE EFFECT OF VIBRATION ON THE FLUIDIZATION BEHAVIOR OF SOME COHESIVE POWDERS

    NARCIS (Netherlands)

    MARRING, E; HOFFMANN, AC; JANSSEN, LPBM

    1994-01-01

    One bed of glass ballotini and several beds of potato starch were fluidized with air at varying fluidization velocities, while the distributor plate was being vibrated at different amplitudes and frequencies to study the effect on the fluidization quality. The degree of cohesiveness of the potato st

  7. Attractive particle interaction forces and packing density of fine glass powders.

    Science.gov (United States)

    Parteli, Eric J R; Schmidt, Jochen; Blümel, Christina; Wirth, Karl-Ernst; Peukert, Wolfgang; Pöschel, Thorsten

    2014-09-02

    We study the packing of fine glass powders of mean particle diameter in the range (4-52) μm both experimentally and by numerical DEM simulations. We obtain quantitative agreement between the experimental and numerical results, if both types of attractive forces of particle interaction, adhesion and non-bonded van der Waals forces are taken into account. Our results suggest that considering only viscoelastic and adhesive forces in DEM simulations may lead to incorrect numerical predictions of the behavior of fine powders. Based on the results from simulations and experiments, we propose a mathematical expression to estimate the packing fraction of fine polydisperse powders as a function of the average particle size.

  8. Method of Making Fine Lithium Iron Phosphate/Carbon-Based Powders with an Olivine Type Structure

    Science.gov (United States)

    Singhal, Amit (Inventor); Dhamne, Abhijeet (Inventor); Skandan, Ganesh (Inventor)

    2008-01-01

    Processes for producing fine LiFePO.sub.4/C and nanostructured LiFe.sub.xM.sub.1-xPO.sub.4/C composite powders, where 1.ltoreq.x.ltoreq.0.1 and M is a metal cation. Electrodes made of either nanostructured LiFe.sub.xM.sub.1-xPO.sub.4 powders or nanostructured LiFe.sub.xM.sub.1-xPO.sub.4/C composite powders exhibit excellent electrochemical properties. That will provide high power density, low cost and environmentally friendly rechargeable Li-ion batteries.

  9. Dispersibility of lactose fines as compared to API in dry powders for inhalation.

    Science.gov (United States)

    Thalberg, Kyrre; Åslund, Simon; Skogevall, Marcus; Andersson, Patrik

    2016-05-17

    This work investigates the dispersion performance of fine lactose particles as function of processing time, and compares it to the API, using Beclomethasone Dipropionate (BDP) as model API. The total load of fine particles is kept constant in the formulations while the proportions of API and lactose fines are varied. Fine particle assessment demonstrates that the lactose fines have higher dispersibility than the API. For standard formulations, processing time has a limited effect on the Fine Particle Fraction (FPF). For formulations containing magnesium stearate (MgSt), FPF of BDP is heavily influenced by processing time, with an initial increase, followed by a decrease at longer mixing times. An equation modeling the observed behavior is presented. Surprisingly, the dispersibility of the lactose fines present in the same formulation remains unaffected by mixing time. Magnesium analysis demonstrates that MgSt is transferred to the fine particles during the mixing process, thus lubrication both BDP and lactose fines, which leads to an increased FPF. Dry particle sizing of the formulations reveals a loss of fine particles at longer mixing times. Incorporation of fine particles into the carrier surfaces is believed to be behind this, and is hence a mechanism of importance as regards the dispersion performance of dry powders for inhalation.

  10. PowderSim: Lagrangian Discrete and Mesh-Free Continuum Simulation Code for Cohesive Soils

    Science.gov (United States)

    Johnson, Scott; Walton, Otis; Settgast, Randolph

    2013-01-01

    PowderSim is a calculation tool that combines a discrete-element method (DEM) module, including calibrated interparticle-interaction relationships, with a mesh-free, continuum, SPH (smoothed-particle hydrodynamics) based module that utilizes enhanced, calibrated, constitutive models capable of mimicking both large deformations and the flow behavior of regolith simulants and lunar regolith under conditions anticipated during in situ resource utilization (ISRU) operations. The major innovation introduced in PowderSim is to use a mesh-free method (SPH-based) with a calibrated and slightly modified critical-state soil mechanics constitutive model to extend the ability of the simulation tool to also address full-scale engineering systems in the continuum sense. The PowderSim software maintains the ability to address particle-scale problems, like size segregation, in selected regions with a traditional DEM module, which has improved contact physics and electrostatic interaction models.

  11. Surface quality analysis of die steels in powder-mixed electrical discharge machining using titan powder in fine machining

    Directory of Open Access Journals (Sweden)

    Banh Tien Long

    2016-06-01

    Full Text Available Improving the quality of surface molds after electrical discharge machining is still being considered by many researchers. Powder-mixed dielectric in electrical discharge machining showed that it is one of the processing methods with high efficiency. This article reports on the results of surface quality of mold steels after powder-mixed electrical discharge machining using titanium powder in fine machining. The process parameters such as electrode material, workpiece material, electrode polarity, pulse on-time, pulse off-time, current, and titanium powder concentration were considered in the research. These materials are most commonly used with die-sinking electrical discharge machining in the manufacture of molds and has been selected as the subject of research: workpiece materials were SKD61, SKT4, and SKD11 mold steels, and electrode materials were copper and graphite. Taguchi’s method is used to design experiments. The influence of the parameters on surface roughness was evaluated through the average value and ratio (S/N. Results showed that the parameters such as electrical current, electrode material, pulse on-time, electrode polarity, and interaction between the electrode materials with concentration powder mostly influence surface roughness and surface roughness at optimal parameters SRopt = 1.73 ± 0.39 µm. Analysis of the surface layer after powder-mixed electrical discharge machining using titanium powder in optimal conditions has shown that the white layer with more uniform thickness and increased hardness (≈861.0 HV, and amount and size of microscopic cracks, is reduced. This significantly leads to the increase in the quality of the surface layer.

  12. Study on fine carbon fiber powder injected into cranium of rabbits

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    AIM: To study dynamically the effect on the rabbits after fine carbon fiber powder was transplanted into their cranium. METHODS: After fine carbon fiber powder was injected into subdural cavity of rabbits, examination of histopathology and EEG were carried out. RESULTS: General observation: 1-104 weeks after injecting, no neuropathological changes concerning with the injecting of the carbon fiber powder were found in the rabbits of experimental group; Under optical microscopes: 1-2 weeks after injecting, slight inflammatory reaction in meninx was found and disappeared generally 4 weeks after injecting, no obvious fiber membrane was found around the carbon fiber, no significant differences were showed between the experimental group (EG) and the control group (CG); Examination of EEG: 1-2 weeks after injecting, slight abnormal changes of EEG in both two groups were showed, but no significant differences was found between them. 4 weeks after injecting, the EEG of the two groups was restored to their normal state before injecting. 1-8 weeks after injecting, no obvious epilepsy waves were showed. CONCLUSION: The fine carbon fiber powder showed excellent histocompatibility after injected into the subdural cavity of rabbits.

  13. Preparation of fine copper powders and their application in BME-MLCC

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The preparation of fine copper powders by chemical reduction method was investigated. The reaction of [Cu(NH3)4] 2+complex with hydrazine hydrate gives spherical monodispersed fine copper powders. The spherical copper powder with a uniform size of 3.5 ± 0.5 μm was processed to obtain flake copper powder having a uniform size of 8-10 μm, excellent dispersibility and uniform shape. The spherical copper powder of 2.5 ± 0.3 μm in size, flake copper, glass frit and vehicle were mixed to prepare copper paste,which was fired in 910-920℃ to obtain BME-MLCC (base metal multilayer ceramic capacitor) with a dense surface of end termination,high adhesion and qualified electrical behavior. Polarized light photo and SEM were employed to observe the copper end termination of BME-MLCC. The rough interface from the interfacial reaction between glass and chip gives high adhesion.

  14. Comparison of the cohesion-adhesion balance approach to colloidal probe atomic force microscopy and the measurement of Hansen partial solubility parameters by inverse gas chromatography for the prediction of dry powder inhalation performance.

    Science.gov (United States)

    Jones, Matthew D; Buckton, Graham

    2016-07-25

    The abilities of the cohesive-adhesive balance approach to atomic force microscopy (AFM) and the measurement of Hansen partial solubility parameters by inverse gas chromatography (IGC) to predict the performance of carrier-based dry powder inhaler (DPI) formulations were compared. Five model drugs (beclometasone dipropionate, budesonide, salbutamol sulphate, terbutaline sulphate and triamcinolone acetonide) and three model carriers (erythritol, α-lactose monohydrate and d-mannitol) were chosen, giving fifteen drug-carrier combinations. Comparison of the AFM and IGC interparticulate adhesion data suggested that they did not produce equivalent results. Comparison of the AFM data with the in vitro fine particle delivery of appropriate DPI formulations normalised to account for particle size differences revealed a previously observed pattern for the AFM measurements, with a slightly cohesive AFM CAB ratio being associated with the highest fine particle fraction. However, no consistent relationship between formulation performance and the IGC data was observed. The results as a whole highlight the complexity of the many interacting variables that can affect the behaviour of DPIs and suggest that the prediction of their performance from a single measurement is unlikely to be successful in every case.

  15. Support for Faraday's View of Circulation in a Fine-Powder Chladni Heap

    Science.gov (United States)

    Thomas, Benku; Squires, Arthur M.

    1998-07-01

    Faraday, like Chladni, saw fine powder collect in a circular heap at an antinode of a vibrating plate. In each vibration cycle, the heap experiences a free-flight interval during which pressure gradients in the heap's interior drive powder centerward, as Faraday proposed. When heap-floor collision terminates flight, pressure gradients reverse direction; but passage of a compaction front has locked particles against further movement. Before a next flight interval, an increase in porosity will reverse the compaction that accompanied heap-floor collision.

  16. Support for Faraday`s View of Circulation in a Fine-Powder Chladni Heap

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, B.; Squires, A.M. [Department of Chemical Engineering, Virginia Polytechnic Institute State University, Blacksburg, Virginia 24061-0211 (United States)

    1998-07-01

    Faraday, like Chladni, saw fine powder collect in a circular heap at an antinode of a vibrating plate. In each vibration cycle, the heap experiences a free-flight interval during which pressure gradients in the heap`s interior drive powder centerward, as Faraday proposed. When heap-floor collision terminates flight, pressure gradients reverse direction; but passage of a compaction front has locked particles against further movement. Before a next flight interval, an increase in porosity will reverse the compaction that accompanied heap-floor collision. {copyright} {ital 1998} {ital The American Physical Society}

  17. Synthesis and characterization of La doped M-type hexagonal barium ferrite fine powders

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The hexagonal BaLaxFe12-xO19 fine powders with M-type structure were synthesized by sol-gel method. The pH of the solution, the molar ratio of nitrate to citric acid and the calcination temperature were investigated to clarify the forming conditions of the ferrites. The crystal structure, grain size, form and magnetic properties were studied by means of XRD, SEM and vibrating sample magnetometer. It is concluded that at pH of 7.0 or so, molar ratio of nitrate to citric acid of 1/3 and calcination temperature of 850  ℃(1  h), 1  000  ℃, M-type BaLaxFe12-xO19 fine powders with a particle size of less than 300  nm was obtained.

  18. Binder-Jet Printing of Fine Stainless Steel Powder with Varied Final Density

    Science.gov (United States)

    Ziaee, Mohsen; Tridas, Eric M.; Crane, Nathan B.

    2017-03-01

    Binder jetting is an additive manufacturing process that produces weak porous parts that are strengthened through sintering and/or infiltration. This article reports on two different methods of preparing fine 316 stainless steel powder and their impact on the final sintered density and dimensions relative to direct printing into space holder to increase porosity. Sintered density and sintering shrinkage of agglomerate material are shown to vary with the density of the spread powder bed. Nevertheless, with added nylon, the shrinkage correlates with the shrinkage of the base steel powder, whereas the density depends on the quantity of the nylon. Thus, it is possible to create varied sintered density with compatible shrinkage levels—a key step toward creating binder-jetting systems with spatially controlled porosity.

  19. The impact of dispersion on selective laser melting of titanium and niobium fine powders mixture

    Science.gov (United States)

    Razin, A.; Ovchinnikov, V.; Akhmetshin, R.; Krinitcyn, M.; Fedorov, V.; Akhmetshina, V.

    2016-11-01

    This paper is dedicated to the study of selective laser melting process of metal powders. Experiments were performed in the Research Center Modern Manufacturing Technologies of TPU with the fine powders of titanium and niobium. The research was carried out on 3D laser printer designed at TPU. In the framework of experiments aimed at determining possibilities of obtaining niobium-titanium alloy by SLS (selective laser sintering) there were studied the basic processes of laser melting and their effect on the quality of final samples and products. We determined operation modes of 3D printers which allow obtaining high quality of printed sample surface. The research results show that rigid requirements related to powder dispersiveness and proportions are needed to achieve better quality of products.

  20. An improved sodium silicate binder modified by ultra-fine powder materials

    Institute of Scientific and Technical Information of China (English)

    WANG Ji-na; FAN Zi-tian; WANG Hua-fang; DONG Xuan-pu; HUANG Nai-yu

    2007-01-01

    This paper presents a new method of modifying sodium silicate binder with ultra-fine powders. The sodium silicate binder modified by ultra-fine powder A and the organic B can reduce the addition amount of the binder. The results indicate that the 24 h strength has increased by 39.9% at room temperature and the residual strength has decreased by 30.7% at 800℃, compared to the conventional sodium silicate. An available material to improve the moisture resistance was also found by adding about 2% more inorganic C, and it can increase the moist strength by 20%. In the end, the microanalyses are given to explain the modifying machanism, i. e., the ultra-fine powder A can refine the sodium silicate binder to avoid holes in the binder bond, which can increase the 24 h strength at room temperture, and can lead to more cracks in the bond after the molding sand is heated to 800℃. This is because of the stress caused by the new eutectic complex of modified sodium silicate binder.

  1. Effects of Fe fine powders doping on hot deformed NdFeB magnets

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Min, E-mail: linm@nimte.ac.cn [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China); Wang, Huijie [Ningbo Jinji Strong Magnetic Material Company, Ningbo 315041 (China); Zheng, Jingwu [Zhejiang University of Technology, Hangzhou 310014 (China); Yan, Aru [Ningbo Institute of Material Technology & Engineering Chinese Academy of Science, Ningbo 315201 (China)

    2015-04-01

    The composite NdFeB magnets with blending melt-spun flakes and Fe fine powders were prepared by the hot-pressed and hot-deformed route. Characterizations of the hot-deformed NdFeB magnets affected by the doped Fe powders were tested. The doped Fe powders decrease the hot-deformed pressure when the strain is between 15 and 50%. XRD patterns show that the doped Fe powders have little influence on the c-axis alignment of hot-deformed NdFeB magnets in the press direction. The B{sub r} and the (BH){sub max} get improved when the doped Fe powders are less than 3 wt%. The doped Fe of hot-deformed NdFeB magnets exists in the elongated state and the spherical state surrounded by the Nd-rich phase. With the Fe fraction increasing, the potential of magnet moves to the positive direction and the diameter of the Nyquist arc becomes larger, which indicate that the corrosion resistance improved effectively. The bending strength was enhanced by the elongated α-Fe phase embedded in the matrix 2:14:1 phase. - Highlights: • The doped Fe powders have little influence on the c-axis alignment of magnets. • The elongated Fe powders are more than the spherical Fe powders in the magnets. • The corrosion resistance is improved effectively with the increasing Fe fraction. • The bending strength is enhanced by the elongated α-Fe phase embedded in the matrix.

  2. Effects of Temperature variations on the Super Fine Powderization of Korean Cultivated Wild Ginseng

    Directory of Open Access Journals (Sweden)

    Jin Ho Kim

    2006-12-01

    Full Text Available Objectives : The aim of this study was to find optimal conditions for producing red ginseng from cultivated wild ginseng using the Turbo Mill. Methods : Characteristics of powdered cultivated wild ginseng based on various temperature settings of the Turbo Mill were observed, and changes in the content was measured by HPLC for various ginsenosides. Results : 1. The diameter of cultivated wild ginseng powder ground by the Turbo Mill was around 10㎛. 2. As the temperature rose, presusre, Specific Mechanical Energy(SME, and density decreased, whileas Water Solubility Index(WSI increased. 3. As the temperature rose, super fine powder showed tendency to turn into dark brown. 4. Measuring content changes by HPLC, there was no detection of ginsenoside Rg3 and ginsenosideRg1, Rb1, and Rh2 concentrations decreased with increase in temperature. Conclusions : Super fine powder of cultivated wild ginseng produced by the Turbo Mill promotes easy absorption of effective ingredients by breaking the cell walls. Using this mechanism to produce red ginseng from cultivated wild ginseng, it yielded less than satisfactory results under the current experiment setup. Furtherresearches are needed to verify more suitable condition for the production of red ginseng.

  3. Liposomal amphotericin B dry powder inhaler: effect of fines on in vitro performance.

    Science.gov (United States)

    Shah, S P; Misra, A

    2004-10-01

    The aim of the present investigation was to improve in vitro pulmonary deposition of amphotericin B (AMB) liposomal dry powder inhaler (LDPI) formulations. Liposomes with negative (AMB1) and positive (AMB2) charge were prepared by the reverse phase evaporation (REV) technique, extruded to reduce size, separated from unentrapped drug and lyophilized using an optimized cryoprotectant to achieve maximum drug retention. Lactose carrier (Sorbolac 400) in varying mass ratio with or without addition of fines (500# sieved Pharmatose 325M) in different mixing sequence were used to formulate AMB LDPI formulations. In vitro evaluation was done with twin stage impinger (TSI) for fine particle fraction. The lactose carrier containing 10% fines was found to be optimum blend at 1:6 mass ratio of liposome: lactose. The addition of fines and order of mixing fines were found to influence the fine particle fraction (FPF) significantly. FPF of LDPI formulations using a Rotahaler (Cipla, India) as delivery device at 30, 60 and 90 L/min were found to be 23.1 +/- 1.5 percent and 17.3 +/- 2.2 percent; 25.3 +/- 1.8 percent and 19.6 +/- 1.5 percent and 28.4 +/- 2.1 percent and 22.9 +/- 1.9 percent for AMB1 and AMB2 respectively.

  4. Preparation of fine nickel powders via reduction of nickel hydrazine complex precursors

    Institute of Scientific and Technical Information of China (English)

    HUANG Guo-yong; XU Sheng-ming; XU Gang; LI Lin-yan; ZHANG Li-feng

    2009-01-01

    Fine nickel(Ni) powders with controllable particle sizes were synthesized via the reduction of nickel hydrazine complex precursors of pure [Ni(N2H4)2]Cl2 and a mixture of [Ni(N2H4)2]Cl2 and [Ni(N2H4)3]Cl2 in aqueous solution. The mechanism of the formation of metallic Ni powders experiences the reduction of nickel hydroxide by hydrazine released from the ligand exchange reaction between nickel hydrazine complex and NaOH. In comparison with the method of preparing Ni powders from nickel salts, the method of making Ni powders via the reduction of nickel hydrazine complex precursors shows the advantages of using half dosage of hydrazine for complete reduction of nickel ions in solution, and the obtained Ni particles show less agglomeration and better dispersibility. Moreover, the average particle size of nickel powders can be controlled from 180 to 260 nm by adjusting the reaction molar ratio and concentration.

  5. SOLIDS CIRCULATION RATE OF ULTRA-FINE POWDERS IN SPOUTED BED WITH DRAFT TUBE%超细粉在导向管喷动床中的固体循环速率

    Institute of Scientific and Technical Information of China (English)

    周勇; 马兰; 石炎福

    2004-01-01

    Ultra-fine powders are difficult to be fluidized due to the strong particle to particle cohesiveness.However, the authors' experiments showed that the ultra-fine powder CaCO3 could be stably fluidized in a spouted bed with a draft tube. The effects of geometric and operating parameters on solid circulation rate of ultra-fine powder CaCO3 were investigated in a 120 mm diameter transparent semicircular spouted bed with a draft tube. Three draft tubes with different sizes were used in this study. It was found that the solids circulation rate was mainly dependent on the drawing rate of the gas jet from the nozzle, then on the gas transport capacity in the draft tube. With increasing gas feed rate, distance between the nozzle and the draft tube inlet and draft tube diameter, the solids circulation rate could be increased. Based on the jet theory, a quantitative correlation was proposed for predicting the solid circulation rate of ultra-fine powders in a spouted bed with a draft tube by taking into account the gas transport capacity in the draft tube.

  6. Influence of dry cohesion on the micro- and macro-mechanical properties of dense polydisperse powders & grains

    Science.gov (United States)

    Kievitsbosch, Robert; Smit, Hendrik; Magnanimo, Vanessa; Luding, Stefan; Taghizadeh, Kianoosh

    2017-06-01

    Understanding how cohesive granular materials behave is of interest for many industrial applications, such as pharmaceutical or food and civil engineering. Models of the behaviour of granular materials on the microscopic scale can be used to obtain macroscopic continuum relations by a micro-macro transition approach. The Discrete Element Method (DEM) is used to inspect the influence of cohesion on the micro and macro behaviour of granular assemblies by using an elasto-plastic cohesive contact model. Interestingly, we observe that frictional samples prepared with different cohesion values show a significant difference in pressure and coordination number in the jammed regime; the differences become more pronounced when packings are closer to the jamming density, i.e. the lowest density where the system is mechanically stable. Furthermore, we observe that cohesion has an influence on the jamming density for frictional samples, but there is no influence on the jamming density for frictionless samples.

  7. Microstructure and properties of liquid-phase sintered tungsten heavy alloys by using ultra-fine tungsten powders

    Institute of Scientific and Technical Information of China (English)

    于洋; 王尔德

    2004-01-01

    The microstructure and properties of liquid-phase sintered 93W-4.9Ni-2.1Fe tungsten heavy alloys using ultra-fine tungsten powders (medium particle size of 700 nm) and original tungsten powders (medium particle size of 3 μm) were investigated respectively. Commercial tungsten powders (original tungsten powders) were mechanically milled in a high-energy attritor mill for 35 h. Ultra-fine tungsten powders and commercial Ni, Fe powders were consolidated into green compacts by using CIP method and liquid-phase sintering at 1 465 ℃ for 30 min in the dissociated ammonia atmosphere. Liquid-phase sintered tungsten heavy alloys using ultra-fine tungsten powders exhibit full densification (above 99% in relative density) and higher strength and elongation compared with conventional liquidphase sintered alloys using original tungsten powders due to lower sintering temperature at 1 465 ℃ and short sintering time. The mechanical properties of sintered tungsten heavy alloy are found to be mainly dependent on the particles size of raw tungsten powders and liquid-phase sintering temperature.

  8. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    Science.gov (United States)

    Gergulova, R.; Tepavitcharova, S.; Rabadjieva, D.; Sezanova, K.; Ilieva, R.; Alexandrova, R.; Andonova-Lilova, B.

    2013-12-01

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg2+ or Zn2+ yielded monophase β-tricalcium phosphate additionally modified with Mg2+ or Zn2+ (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated.

  9. Biomimetic synthesis of modified calcium phosphate fine powders and their in vitro studies

    Energy Technology Data Exchange (ETDEWEB)

    Gergulova, R., E-mail: rumigg@yahoo.com; Tepavitcharova, S., E-mail: rumigg@yahoo.com; Rabadjieva, D., E-mail: rumigg@yahoo.com; Sezanova, K., E-mail: rumigg@yahoo.com; Ilieva, R., E-mail: rumigg@yahoo.com [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, Acad. G. Bonchev Str., Bl. 11, 1113 Sofia (Bulgaria); Alexandrova, R.; Andonova-Lilova, B. [Institute of Experimental Morphology, Pathology and Anthropology with Museum, BAS, Acad. G. Bonchev Str., Bl. 25, Sofia (Bulgaria)

    2013-12-16

    Biomimetic approach and subsequent high-temperature treatment were used to synthesize ion modified calcium phosphate fine powders. Thus, using Simulated Body Fluid (SBF) as an ion modifier, a bi-phase mixture of ion modified β-tricalcium phosphate and hydroxyapatite (β-TCP + HA) was prepared. The use of SBF electrolyte solution enriched with Mg{sup 2+} or Zn{sup 2+} yielded monophase β-tricalcium phosphate additionally modified with Mg{sup 2+} or Zn{sup 2+} (Mg-β-TCP or Zn-β-TCP). The in vitro behavior of the prepared powders on cell viability and proliferation of murine BALB/c 3T3 fibroblasts and of human Lep 3 cells was studied by MTT test assays and Mosmann method after 72 h incubation. The relative cell viability was calculated.

  10. DYNAMIC RHEOLOGICAL BEHAVIOR OF POLYPROPYLENE FILLED WITH ULTRA-FINE POWDERED RUBBER PARTICLES

    Institute of Scientific and Technical Information of China (English)

    Qiang Zheng; Yan-xia Cao; Miao Du

    2004-01-01

    Dynamic rheological characteristics of polypropylene (PP) filled with ultra-fine full-vulcanized powdered rubber (UFPR) composed of styrene-butadiene copolymer were studied through dynamic rheological measurements on an Advanced Rheometric Expansion System (ARES). A specific viscoelastic phenomenon, i.e. "the second plateau", appeared at low frequencies, and exhibits a certain dependence on the amount of rubber particles and the dispersion state in the matrix. This phenomenon is attributed to the formation of aggregation structure of rubber particles. The analyses of Cole-Cole diagrams of the dynamic viscoelastic functions suggest that the heterogeneity of the composites is enhanced on increasing both particle content and temperature.

  11. Transcatheter arterial chemoembolization with a fine-powder formulation of cisplatin for hepatocellular carcinoma

    Institute of Scientific and Technical Information of China (English)

    Kazuhiro; Kasai; Akira; Ushio; Kei; Sawara; Yasuhiro; Miyamoto; Yukiho; Kasai; Kanta; Oikawa; Hidekatsu; Kuroda; Yasuhiro; Takikawa; Kazuyuki; Suzuki

    2010-01-01

    AIM:To evaluate the efficacy of transcatheter arterial chemoembolization(TACE) using a suspension of a fine-powder formulation of cisplatin(DDPH) for hepatocellular carcinoma(HCC).METHODS:The study population was comprised of 164 patients who were treated by TACE alone.Of these patients,76 underwent TACE using a suspension of DDPH in lipiodol(LPD)(DDPH group),and the remaining 88 underwent TACE with an emulsion of doxorubicin(ADM) with LPD(ADM group).We compared the DDPH group with the ADM group in terms of...

  12. Effect of adhesive thickness and surface treatment on shear strength on single lap joint Al/CFRP using adhesive of epoxy/Al fine powder

    Science.gov (United States)

    Diharjo, Kuncoro; Anwar, Miftahul; Tarigan, Roy Aries P.; Rivai, Ahmad

    2016-02-01

    The objective of this study is to investigate the effect of adhesive thickness and surface treatment on the shear strength and failure type characteristic of single lap joint (SLJ) CFRP/Al using adhesive epoxy/Al-fine-powder. The CFRP was produced by using hand layup method for 30% of woven roving carbon fiber (w/w) and the resin used was bisphenolic. The adhesive was prepared using 12.5% of aluminum fine powder (w/w) in the epoxy adhesive. The powder was mixed by using a mixing machine at 60 rpm for 6 minutes, and then it was used to join the Al plate-2024 and CFRP. The start time to pressure for the joint process was 20 minutes after the application of adhesive on the both of adherends. The variables in this research are adhesive thickness (i.e. 0.2 mm, 0.4 mm, 0.6 mm, 0.8 mm and 1 mm) and surface treatment of adherends (i.e. acetone, chromate sulphuric acid, caustic etch and tucker's reagent). Before shear testing, all specimens were post-cured at 100 °C for 15 minutes. The result shows that the SLJ has the highest shear strength for 0.4 mm of adhesive thickness. When the adhesive thickness is more than 0.4 mm (0.6-1 mm), the shear strength decreases significantly. It might be caused by the property change of adhesive from ductile to brittle. The acetone surface treatment produces the best bonding between the adhesive and adherends (CFRP and Al-plate 2024), and the highest shear strength is 9.31 MPa. The surface treatment give the humidification effect of adherend surfaces by adhesive. The failure characteristic shows that the mixed failure of light-fiber-tear-failure and cohesive-failure are occurred on the high shear strength of SLJ, and the low shear strength commonly has the adhesive-failure type.

  13. Enzymatic hydrolysis of anchovy fine powder at high and ambient pressure, and characterization of the hydrolyzates.

    Science.gov (United States)

    Kim, Namsoo; Son, So-Hee; Maeng, Jin-Soo; Cho, Yong-Jin; Kim, Chong-Tai

    2016-02-01

    At specific conditions of high pressure, the stability and activity of some enzymes are reportedly known to increase. The aim of this study was to apply pressure-tolerant proteases to hydrolyzing anchovy fine powder (AFP) and to determine product characteristics of the resultant hydrolyzates. Anchovy fine powder enzyme hydrolyzates (AFPEHs) were produced at 300 MPa and ambient pressure using combinations of Flavourzyme 500MG, Alcalase 2.4L, Marugoto E and Protamex. When the same protease combination was used for hydrolysis, the contents of total soluble solids, total water-soluble nitrogen and trichloroacetic acid-soluble nitrogen in the AFPEHs produced at 300 MPa were conspicuously higher than those in the AFPEHs produced at ambient pressure. This result and electrophoretic characteristics indicated that the high-pressure process of this study accelerates protein hydrolysis compared with the ambient-pressure counterpart. Most peptides in the hydrolyzates obtained at 300 MPa had molecular masses less than 5 kDa. Functionality, sensory characteristics and the content of total free amino acids of selected hydrolyzates were also determined. The high-pressure hydrolytic process utilizing pressure-tolerant proteases was found to be an efficient method for producing protein hydrolyzates with good product characteristics. © 2015 Society of Chemical Industry.

  14. Histopathological study on fine carbon fiber powder injected into the subdural space of mice

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    AIM and METHODS: After the fine carbon fiber powder was injected into the right subdural space of the mice, dynamic observation was carried out on their movement and histopathological changes. RESULTS: 1-52 weeks after the injecting, no neurological changes concerning with the implanting of the carbon fiber powder were found in the experimental mice. The fine carbon fiber extensively located on the inter surface of the dura mater membrane of the right temporalis and the out surface of pie mater. Only slight inflammatory cells reaction was found under optical microscopes. The degree of inflammation reaction are Grade Ⅱ 1 week after injection and was Grade Ⅰ 2 weeks after injection, inflammation was disappeared 4 weeks after injection. No obvious fiber membrane was found around the implanted materials. No significant differences were found between the experimental and the control group.CONCLUSION: It was showed that the carbon fiber shares excellent histocompatibility after injected into the subdural space and subarechnoid cavity of the right temple of mice.

  15. On the preparation of fine V8 C7-WC and V4 C 3-WC powders

    CSIR Research Space (South Africa)

    Osborne, C

    1997-01-01

    Full Text Available The aim of this work was to produce V8 C7-WC and V4 C 3-WC powders with grain size between 1 and 2mu-m, as a first stage of the preparation of fine grained WC-VC-Co hardmetal. V8 C7-WC powder was produced via two routes: starting from preformed V8 C7...

  16. Low-velocity pneumatic conveying in horizontal pipe for coarse particles and fine powders

    Institute of Scientific and Technical Information of China (English)

    Yuji Tomita; Vijay Kumar Agarwal; Hiroyuki Asou; Katsuya Funatsu

    2008-01-01

    First,the characteristics of low-velocity conveying of particles having different hardness are experimentally investigated in a horizontal pipeline in terms of flow pattern and pressure drop to show that the slug flow can be classified into two types depending on the settling of particles along the pipeline,and the period is small for slug flow without the settled layer,which is called solitary slug flow.The pressure drop for soft particles is shown to be larger than that for hard particles.Then,experimental results are presented on horizontal fluidized-bed conveying of fine powders to show that air release from the top surface of the conveying channel is an important factor for high mass flow rate of particles.

  17. Preparation of Strontium Bismuth Tantalum (SBT) Fine Powder by Sol-Gel Process Using Bismuth Subnitrate as Bismuth Source

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Strontium bismuth tantalum (SBT) fine power was prepared by Sol-Gel method. Pentaethoxy tantalum, strontium acetate and bismuth subnitrate were used as raw materials, and were dissolved in proper order in ethylene glycol to form transparent sol. The mixed precursor was dried at 80°C and annealed at 800°C for 1 h. Crystallized nanometer sized SBT fine powder was obtained and characterized by XRD.

  18. Predicting the Fine Particle Fraction of Dry Powder Inhalers Using Artificial Neural Networks.

    Science.gov (United States)

    Muddle, Joanna; Kirton, Stewart B; Parisini, Irene; Muddle, Andrew; Murnane, Darragh; Ali, Jogoth; Brown, Marc; Page, Clive; Forbes, Ben

    2017-01-01

    Dry powder inhalers are increasingly popular for delivering drugs to the lungs for the treatment of respiratory diseases, but are complex products with multivariate performance determinants. Heuristic product development guided by in vitro aerosol performance testing is a costly and time-consuming process. This study investigated the feasibility of using artificial neural networks (ANNs) to predict fine particle fraction (FPF) based on formulation device variables. Thirty-one ANN architectures were evaluated for their ability to predict experimentally determined FPF for a self-consistent dataset containing salmeterol xinafoate and salbutamol sulfate dry powder inhalers (237 experimental observations). Principal component analysis was used to identify inputs that significantly affected FPF. Orthogonal arrays (OAs) were used to design ANN architectures, optimized using the Taguchi method. The primary OA ANN r(2) values ranged between 0.46 and 0.90 and the secondary OA increased the r(2) values (0.53-0.93). The optimum ANN (9-4-1 architecture, average r(2) 0.92 ± 0.02) included active pharmaceutical ingredient, formulation, and device inputs identified by principal component analysis, which reflected the recognized importance and interdependency of these factors for orally inhaled product performance. The Taguchi method was effective at identifying successful architecture with the potential for development as a useful generic inhaler ANN model, although this would require much larger datasets and more variable inputs.

  19. Influence and Characterization of Acidity on Fine Silicon Powder Immobilized Photocatalyst

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    TiO2 photocatalyst was supported with tetrabutyl titanate sol as precursor and fine silicon powder obtained from ferroalloys factory as carrier to discuss the influence of pH value of gel precursor on microstructure and activity of photocatalyst in the process of synthesizing nano-TiO2 by using sol-gel method, the purpose of which is to provide fundamental data for the recycle of photocatalytic material.Under the irradiation of ultraviolet light, the photocatalytic degradation rate of methyl orange solution was used to characterize the photocatalytic activity of the sample.The specific surface area of the sample was tested by N2 desorption method, crystal form of TiO2 was analyzed by X-ray powder diffraction, and the microtopography of the sample wasobserved by scanning electron microscopy.The experimental results showed that the acidity of gel precursor could greatly affect the specific surface area and photocatalytic activity of the pho-tocatalyst, and the optimum pH value of the precursor was determined as 2.0, and at this time the specific surface area of photocatalyst could reach 34.0 m2/g.In the sample, the proporticn of anatase to futile is 7:3, which makes 10 mg·L-1 methyl orange solution fade after irradiation by 15Wultraviolet light for 24 h, and the degradation rate might be up to 98.1%.

  20. Removal of Chloroform from Hydrochloride Acid Solution Using Fine Powder of Polymer as Adsorbent

    Institute of Scientific and Technical Information of China (English)

    LU,Yingzhou; QUE,Yong; LI,Chunxi; MENG,Hong; WANG,Zihao

    2009-01-01

    In order to choose a suitable adsorbent for the removal of chloroform from its hydrochloric acid solution,the adsorptive ability of some polymer adsorbents was investigated in terms of their adsorption curves in water and 20% hydrochloric acid solutions at 298.15 K,and compared with that of active carbon (AC) and solid paraffin (SP).The adsorbents studied include the fine powders of chlorinated rubber (CR),polypropylene (PP),chlorinated polypropylene (CPP) and polyvinylchloride (PVC).The results showed that the adsorption behavior followed the Langmuir equation and the adsorption ability of these adsorbents followed the order AC > PVC > CR > PP > CPP> SP.This order is basically in line with the decrease of chloro-content of the adsorbents from PVC to SP.The adsorptivity of PVC and CR was nearly equivalent to that of AC with their saturated adsorption being about 1.4 g-CHCl3 (g-absorbent) -1.For all adsorbents studied,the adsorption capacity always decreases with the increase of hydrochloric acid concentration.It is showed that the commercial polymer powder of PVC or CR can be used as an efficient absorbent for the removal of chloroform from its aqueous solution for its low cost,good adsorption ability and ease of thermal desorption for recycling.

  1. Evaluation of rock powdering methods to obtain fine-grained samples for CHEMIN, a combined XRD/XRF instrument

    Energy Technology Data Exchange (ETDEWEB)

    Chipera, S. J. (Steve J.); Vaniman, D. T. (David T.); Bish, D. L. (David L.); Sarrazin, P.; Feldman, S.; Blake, D.; Bearman, G. H. (Gregory H.); Bar-Cohen, Yoseph

    2004-01-01

    A miniature XRD/XRD (X-ray diffraction/X-ray fluorescence) instrument, CHEMIN, is currently being developed for definite mineralogic analysis of soils and rocks on Mars. One of the technical issues that must be addressed to enable remote XRD analysis is how best to obtain a representative sample powder for analysis. For powder XRD analyses, it is beneficial to have a fine-grained sample to reduce preferred orientation effects and to provide a statistically significant number of crystallites to the X-ray beam. Although a two-dimensional detector as used in the CHEMIN instrument produces good results even with poorly prepared powder, the quality of the data improves and the time required for data collection is reduced if the sample is fine-grained and randomly oriented. A variety of methods have been proposed for XRD sample preparation. Chipera et al. presented grain size distributions and XRD reuslts from powders generated with an Ultrasonic/Sonic Driller/Corer (USDC) currently being developed at JPL. The USDC was shown to be an effective instrument for sampling rock to produce powder suitable for XRD. In this paper, they compare powder prepared using the USDC with powder obtained with a miniaturized rock crusher developed at JPL and with powder obtained with a rotary tungsten carbide bit to powders obtained from a laboratory bench-scale Retsch mill (provides benchmark mineralogical data). These comparisons will allow assessment of the suitability of these methods for analysis by an XRD/XRD instrument such as CHEMIN.

  2. Particle-based simulations of powder coating in additive manufacturing suggest increase in powder bed roughness with coating speed

    Directory of Open Access Journals (Sweden)

    Parteli Eric J. R.

    2017-01-01

    Full Text Available We have developed the first particle-based numerical tool to simulate the coating of powder particles in additive manufacturing devices. Our Discrete Element Method considers realistic particle shapes and incorporates attractive interaction (van-der-Waals forces between the particles. From simulations of powder coating using a roller as coating device, we find that the surface roughness of the powder bed scales with the square of coating speed. Moreover, we find that using fine, highly polydisperse powders may lead to larger powder bed roughness, compared to process simulations using coarser powders, due to the formation of agglomerates resulting from cohesive forces.

  3. Particle-based simulations of powder coating in additive manufacturing suggest increase in powder bed roughness with coating speed

    Science.gov (United States)

    Parteli, Eric J. R.; Pöschel, Thorsten

    2017-06-01

    We have developed the first particle-based numerical tool to simulate the coating of powder particles in additive manufacturing devices. Our Discrete Element Method considers realistic particle shapes and incorporates attractive interaction (van-der-Waals) forces between the particles. From simulations of powder coating using a roller as coating device, we find that the surface roughness of the powder bed scales with the square of coating speed. Moreover, we find that using fine, highly polydisperse powders may lead to larger powder bed roughness, compared to process simulations using coarser powders, due to the formation of agglomerates resulting from cohesive forces.

  4. Understanding the influence of powder flowability, fluidization and de-agglomeration characteristics on the aerosolization of pharmaceutical model powders.

    Science.gov (United States)

    Zhou, Qi Tony; Armstrong, Brian; Larson, Ian; Stewart, Peter J; Morton, David A V

    2010-08-11

    The aim of this study was to investigate the influence of the intrinsic inter-particulate cohesion of model pharmaceutical powders on their aerosolization from a dry powder inhaler. Two cohesive poly-disperse lactose powders with median particle sizes of around 4 and 20 microm were examined. The results showed that after dry coating with magnesium stearate, their flowability, fluidization and de-agglomeration behaviours could be substantially improved, as indicated by powder rheometry, shear testing and laser diffraction aerosol testing. This was achieved by reducing their cohesiveness via surface modification. In contrast to some previous reports, this study demonstrated how powder aerosolization may be improved more significantly and consistently (for widely varying air flow rates) by substantially reducing their inter-particulate cohesive forces. This study contributes to the understanding of the relationship between intrinsic cohesive nature and bulk properties such as flowability, fluidization and de-agglomeration and its impact on their aerosolization, which is fundamental and critical in the optimal design of dry powder inhaler formulations. The intensive mechanical dry coating technique also demonstrated a promising potential to improve aerosolization efficiency of fine cohesive model powders.

  5. Optimal Conditions for Preparing Ultra-Fine CeO2 Powders in A Submerged Circulative Impinging Stream Reactor

    Institute of Scientific and Technical Information of China (English)

    Chi Ru'an; Xu Zhigao; Wu Yuanxin; Wang Cunwen

    2007-01-01

    Cerium carbonate powders were produced in a submerged circulation impinging stream reactor (SCISR) from Ce(NO3)3·6H2O. NH4HCO3 was used as a precipitant in the reaction. Cerium carbonate powders were roasted to produce ultra-fine cerium dioxide (CeO2) powders. The optimal conditions of such production process were obtained by orthogonal and one-factor experiments. The results showed that ultra-fine and narrowly distributed cerium carbonate powders were produced under the optimal flowing conditions. The concentrations of Ce(NO3)3 and NH4HCO3 solutions were 0.25 and 0.3 mol·L-1, respectively. The concentration of PEG4000 added in these two solutions was 4 g·L-1. The stirring ratio, reaction temperature, feeding time, solution pH, reaction time and digestion time were 900 r·min-1, 80 ℃, 20 min, 5~6, 5 min and 1 h, respectively. The final product, CeO2 powders, was obtained by roasting the produced cerium carbonate in air for 3 h at 500 ℃. The finally produced CeO2 powders were torispherical particles with a narrow size distribution of 0.8~2.5 μm. The crystal structure of CeO2 powders belonged to cubic crystal system and its space point group was O5H-FM3M. Under optimal conditions, powders produced by SCISR were finer and more narrowly distributed than that by Stirred Tank Reactor (STR).

  6. Mathematical description of SO/sub 2/ absorption in an aqueous suspension of finely powdered limestone

    Energy Technology Data Exchange (ETDEWEB)

    Biba, V.; Hrncir, J.; Vejvoda, J.

    1978-01-01

    A mathematical model has been proposed that characterizes the course of SO/sub 2/ absorption in a bubble reactor filled by a suspension of finely powdered limestone. The agreement between the experimental results and the calculated course of the output SO/sub 2/ concentration shows that the model represents a useful basis for the description of the studied process. However, as the model has been so far verified only on one sample at a single temperature and for only one grain composition, the results obtained can be considered only as the first step in the modelling of the process. Experiments performed under different condition of temperature, grain composition and with different types of limestone, and/or some further additions to the reaction scheme involved (e.g., the dissociation of carbonates) are needed to make the model more accurate. The results so far obtained represent thus a contribution to the approximation of the fundamental theory of processes that take place in the wet limestone technology of desulphurization of combustion gases.

  7. Probing of Metabolites in Finely Powdered Plant Material by Direct Laser Desorption Ionization Mass Spectrometry

    Science.gov (United States)

    Musharraf, Syed Ghulam; Ali, Arslan; Choudhary, M. Iqbal; Atta-ur-Rahman

    2014-04-01

    Natural products continue to serve as an important source of novel drugs since the beginning of human history. High-throughput techniques, such as MALDI-MS, can be techniques of choice for the rapid screening of natural products in plant materials. We present here a fast and reproducible matrix-free approach for the direct detection of UV active metabolites in plant materials without any prior sample preparation. The plant material is mechanically ground to a fine powder and then sieved through different mesh sizes. The collected plant material is dispersed using 1 μL solvent on a target plate is directly exposed to Nd:YAG 335 nm laser. The strategy was optimized for the analysis of plant metabolites after study of the different factors affecting the reproducibility and effectiveness of the analysis, including particle sizes effects, types of solvents used to disperse the sample, and the part of the plant analyzed. Moreover, several plant species, known for different classes of metabolites, were screened to establish the generality of the approach. The developed approach was validated by the characterization of withaferin A and nicotine in the leaves of Withania somnifera and Nicotiana tabacum, respectively, through comparison of its MS/MS data with the standard compound. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques were used for the tissue imaging purposes. This approach can be used to directly probe small molecules in plant materials as well as in herbal and pharmaceutical formulations for fingerprinting development.

  8. Preparation of NiO-CuO-MgO fine powders by ultrasonic spray pyrolysis for carbon nanofibers synthesis

    Science.gov (United States)

    Krasnikova, Irina V.; Mishakov, Ilya V.; Bauman, Yury I.; Karnaukhov, Timofey M.; Vedyagin, Aleksey A.

    2017-09-01

    Carbon nanofibers with uniform diameter distribution are of great importance to be applied in composite materials production. Characteristics of the final carbon product obtained via catalytic chemical vapour deposition are known to be determined by the catalyst characteristics and the process conditions. In this work, ultrasonic spray pyrolysis was used for the preparation of uniform-sized NiO-CuO-MgO fine powders. Spherical particles of 170-340 nm in diameter were obtained in a temperature range of 400-600 °C. Synthesized powders exhibited high catalytic activity in CCVD of ethylene with the formation of CNF with relatively narrow diameter distribution (60 ± 20 nm).

  9. Effect of positron source irradiation on positronium annihilation in fine powdered alumina

    Science.gov (United States)

    Liu, Z. W.; Chen, Z. Q.

    2016-09-01

    Positron lifetime and Doppler broadening of positron annihilation radiation were measured as a function of time to study the irradiation effect by 22Na positron source in fine powdered alumina. The γ-Al2O3 samples were put in a vacuum chamber with a pressure of about 10-6 Torr and were cooled down to 10 K by a closed-cycle helium gas refrigerator. The irradiation of γ-Al2O3 samples by positron source was taken for a duration of about two days immediately after the sample was cooled down. After that, the sample was subjected to a warm up process from 10 K to 300 K with a step of 10 K. Positron lifetime and Doppler broadening spectra were measured simultaneously during these processes. Two long lifetime components corresponding to ortho-positronium annihilation were observed. A significant shortening of these long lifetime components and a large increase in S parameter is observed during irradiation. It is supposed that positron source irradiation creates a large number of paramagnetic centers on the surface of the γ-Al2O3 grains, which induce spin conversion quenching of positronium. The irradiation induced paramagnetic centers are unstable above 70 K and are nearly annealed out when the temperature rises to 190 K. After warming up of the sample to room temperature, the positron lifetime spectrum is identical to that before irradiation. It was also found that after irradiation, a medium long lifetime component of about 5 ns appears, of which the intensity increases with increasing irradiation time. This may be originated from the formation of the surface o-Ps state. This surface o-Ps state is also inhibited at elevated temperatures. Our results indicate that positronium is a very sensitive probe for the surface defects in porous materials.

  10. Effect of positron source irradiation on positronium annihilation in fine powdered alumina

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Z.W.; Chen, Z.Q.

    2016-09-30

    Highlights: • Effect of positron irradiation was studied using both positron lifetime and Doppler. • Positron source irradiation creates paramagnetic centers on the surface of alumina. • Paramagnetic centers induced spin conversion quenching of positronium. • Paramagnetic centers are unstable above 70 K and nearly vanish above 190 K. • Positronium is a sensitive probe for the surface defects in porous materials. - Abstract: Positron lifetime and Doppler broadening of positron annihilation radiation were measured as a function of time to study the irradiation effect by {sup 22}Na positron source in fine powdered alumina. The γ-Al{sub 2}O{sub 3} samples were put in a vacuum chamber with a pressure of about 10{sup −6} Torr and were cooled down to 10 K by a closed-cycle helium gas refrigerator. The irradiation of γ-Al{sub 2}O{sub 3} samples by positron source was taken for a duration of about two days immediately after the sample was cooled down. After that, the sample was subjected to a warm up process from 10 K to 300 K with a step of 10 K. Positron lifetime and Doppler broadening spectra were measured simultaneously during these processes. Two long lifetime components corresponding to ortho-positronium annihilation were observed. A significant shortening of these long lifetime components and a large increase in S parameter is observed during irradiation. It is supposed that positron source irradiation creates a large number of paramagnetic centers on the surface of the γ-Al{sub 2}O{sub 3} grains, which induce spin conversion quenching of positronium. The irradiation induced paramagnetic centers are unstable above 70 K and are nearly annealed out when the temperature rises to 190 K. After warming up of the sample to room temperature, the positron lifetime spectrum is identical to that before irradiation. It was also found that after irradiation, a medium long lifetime component of about 5 ns appears, of which the intensity increases with increasing

  11. Preparation of copper-coated fine molybdenum powders with electroless technique

    Institute of Scientific and Technical Information of China (English)

    WANG Guang-jun; WANG De-zhi; ZHOU Jie; WU Zhuang-zhi

    2009-01-01

    The molybdenum powders with average particle size of 3 μm were coated with copper by electroless plating. The influence of pretreatment, solution composition and plating conditions on electroless copper plating was studied. The copper-coated molybdenum powders were examined by SEM and XRD. Results indicate that a series of optimization methods is used to add activated sites before electroless copper plating. Taking TEA and EDTA as chief and assistant complex agents respectively, 2,2'-bipyridyl and PEG as double stabilizers, the Mo powders are coated with copper successfully with little Cu2O contained, at the same time, Mo-Cu composite powders with copper content of 15 - 85 wt% can be obtained. The optimal values of pH, temperature and HCHO concentration are 12- 13, 60-65 ℃ and 22-26 mL/L, respectively.

  12. Optimization of the EMI shielding effectiveness of fine and ultrafine POFA powder mix with OPC powder using Flower Pollination Algorithm

    Science.gov (United States)

    Narong, L. C.; Sia, C. K.; Yee, S. K.; Ong, P.; Zainudin, A.; Nor, N. H. M.; Kasim, N. A.

    2017-01-01

    In order to solve the electromagnetic interference (EMI) issue and provide a new application for palm oil fuel ash (POFA), POFA was used as the cement filler for enhancing the EMI absorption of cement-based composites. POFA was refined by using water precipitation for 24 hours to remove the filthiness and distinguish the layer 1 (floated) and layer 2 (sink) of POFA. Both layers POFA were dried for 24 hours at 100 ± 5 °C and grind separately for sieve at 140 μm (Fine) and 45 цш sizes (Ultrafine). The micro structure and element content of the both layers POFA were characterized by scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) respectively. The results showed layer 1 POFA has potentialities for EMI shielding effectiveness (SE) due to its higher carbon content and porous structure. The study reveals that EMI SE also influenced by the particle size of POFA, where smaller particle size can increase 5 % to 13 % of EMI SE. When the specimen consists of 50% POFA with passing through 45 μm sieve, the EMI was shield -13.08 dB in between 50 MHz to 2 GHz range. Flower Pollination Algorithm (FPA) proves that POFA passing 45 μm sieve with 50% mixed to OPC is optimal parameter. The error between experimental and FPA simulation data is below 1.2 for both layers POFA.

  13. Preparation and electrical characterization of ultra-fine powder scandia-stabilized zirconia

    Institute of Scientific and Technical Information of China (English)

    周静; 张赫; 徐宏; 薛倩楠; 黄小卫; 冯宗玉; 龙志奇

    2016-01-01

    Ultrafine powders of scandia-stabilized zirconia (ScSZ) were prepared by the co-precipitation method, using ZrOCl2 and ScO2 as raw materials and NH3·H2O as a precipitant. In this paper, the optimum process parameters were investigated. The pH of the reaction solution directly impacted the precursor structure, which further affected the obtained crystal forming. Many experiment methods of thermogravimetric analysis and differential thermal analysis (TG-DTA), X-ray diffraction (XRD), transmission electron microscopy (TEM), Raman spectroscopy (Raman), and nitrogen adsorption were employed to characterize the ScSZ powder. The structure transition mechanism from cubic to rhombohedral was discussed. In addition, the electrical conductivity of the powders was also studied after dry-pressing and calcining. The results showed that the structure of ScSZ with complete crystal surface belonged to the cubic phase. The crystallite sizes of the powders prepared are about 60–80 nm, meet the conditions of (D90–D10)/2D50≤1, and ex-hibited the good flow properties. The electrical conductivity was more than 190 mS/cm in air measured at 850 ºC.

  14. A Process Study for Manufacturing Ultra-Fine Titaniumn Diboride Powder.

    Science.gov (United States)

    1986-05-01

    powder. The reaction used was the carbo- thermic reduction of boron carbide in the presence of highly reactive titanium dioxide. The resultant titanium...REQUIREMENTS Space: Approximately 5,000 square feet of open, standard butler type construction with 20’ ceiling clearance. Concrete floor - no special

  15. Magnetic properties of TCr2O4 (T = Co, Ni) fine powders and TCr2O4/SiO2 nanocomposites

    Science.gov (United States)

    Mantlikova, Alice; Poltierova Vejpravova, Jana; Holec, Petr; Plocek, Jiri; Niznansky, Daniel

    2011-10-01

    We have studied magnetic properties of TCr2O4 (T = Co, Ni) fine powders, obtained by the citric acid method, and TCr2O4/SiO2 nanocomposites, constituted of spinel nanoparticles embedded in silica matrix fabricated by a modified sol gel method. All samples were characterized by powder X-ray diffraction, scanning electron microscopy and microprobe analysis. The profile analysis of the powder X-ray diffraction revealed that the particle size is larger for the fine powder samples, as expected. Detailed measurements of magnetization, hysteresis loops and a.c. susceptibility demonstrate significant differences in magnetic properties of the fine powders in comparison to the nanocomposite samples. The values of the coercitivity at 10 K ranges from ≈ 2T for NiCr2O4 fine powders to ≈ 0.6 T for CoCr2O4/SiO2 nanocomposites. Moreover, the hysteresis loops of the NiCr2O4/SiO2 samples are brightly asymmetric. The phenomenon will be discussed in context of the exchange-bias originated by presence of a tiny amount of the antiferromagnetic phase, Cr2O3 in the samples.

  16. Super-fine powdered activated carbon (SPAC) for efficient removal of micropollutants from wastewater treatment plant effluent.

    Science.gov (United States)

    Bonvin, Florence; Jost, Livia; Randin, Lea; Bonvin, Emmanuel; Kohn, Tamar

    2016-03-01

    In an effort to mitigate the discharge of micropollutants to surface waters, adsorption of micropollutants onto powdered activated carbon (PAC) after conventional wastewater treatment has been identified as a promising technology for enhanced removal of pharmaceuticals and pesticides from wastewater. We investigated the effectiveness of super-fine powdered activated carbon, SPAC, (ca. 1 μm mean particle diameter) in comparison to regular-sized PAC (17-37 μm mean diameter) for the optimization of micropollutant removal from wastewater. Adsorption isotherms and batch kinetic experiments were performed for 10 representative micropollutants (bezafibrate, benzotriazole, carbamazepine, diclofenac, gabapentin, mecoprop, metoprolol, ofloxacin, sulfamethoxazole and trimethoprim) onto three commercial PACs and their super-fine variants in carbonate buffer and in wastewater effluent. SPAC showed substantially faster adsorption kinetics of all micropollutants than conventional PAC, regardless of the micropollutant adsorption affinity and the solution matrix. The total adsorptive capacities of SPAC were similar to those of PAC for two of the three tested carbon materials, in all tested waters. However, in effluent wastewater, the presence of effluent organic matter adversely affected micropollutant removal, resulting in lower removal efficiencies especially for micropollutants with low affinity for adsorbent particles in comparison to pure water. In comparison to PAC, SPAC application resulted in up to two-fold enhanced dissolved organic carbon (DOC) removal from effluent wastewater. The more efficient adsorption process using SPAC translates into a reduction of contact time and contact tank size as well as reduced carbon dosing for a targeted micropollutant removal. In the tested effluent wastewater (5 mg/L DOC), the necessary dose to achieve 80% average removal of indicator micropollutants (benzotriazole, diclofenac, carbamazepine, mecoprop and sulfamethoxazole) ranged

  17. An investigation into the effect of fine lactose particles on the fluidization behaviour and aerosolization performance of carrier-based dry powder inhaler formulations.

    Science.gov (United States)

    Kinnunen, Hanne; Hebbink, Gerald; Peters, Harry; Shur, Jagdeep; Price, Robert

    2014-08-01

    The effect of milled and micronized lactose fines on the fluidization and in vitro aerosolization properties of dry powder inhaler (DPI) formulations was investigated, and the suitability of static and dynamic methods for characterizing general powder flow properties of these blends was assessed. Lactose carrier pre-blends were prepared by adding different lactose fines (Lactohale® (LH) 300, 230 and 210) with coarse carrier lactose (Lactohale100) at 2.5, 5, 10 and 20 wt% concentrations. Powder flow properties of lactose pre-blends were characterized using the Freeman Technology FT4 and Schulze RST-XS ring shear tester. A strong correlation was found between the basic flow energy (BFENorm) measured using the Freeman FT4 Rheometer and the flowability number (ffc) measured on Schulze RST-XS. These data indicate that both static and dynamic methods are suitable for characterizing general powder flow properties of lactose carriers. Increasing concentration of fines corresponded with an increase in the normalized fluidization energy (FENorm). The inclusion of fine particles of lactose resulted in a significant (p lactose containing up to 10 wt% LH300. A similar trend was found for the milled lactose grades LH230 and LH210. However, the increase in FENorm upon addition of milled fines only corresponded to a very slight improvement in the performance. These data suggest that whilst the fluidization energy correlated with fine particle delivery, this relationship is specific to lactose grades of similar particle size.

  18. Adsorption of Remazol Brilliant Blue R using ZnO fine powder: Equilibrium, kinetic and thermodynamic modeling studies

    Energy Technology Data Exchange (ETDEWEB)

    Ada, Kezban [Department of Chemistry, Faculty of Arts and Sciences, Kirikkale University, 71450 Yahsihan-Kirikkale (Turkey); Ergene, Aysun, E-mail: ayergene@yahoo.com [Department of Biology, Faculty of Arts and Sciences, Kirikkale University, 71450 Yahsihan-Kirikkale (Turkey); Tan, Sema; Yalcin, Emine [Department of Biology, Faculty of Arts and Sciences, Kirikkale University, 71450 Yahsihan-Kirikkale (Turkey)

    2009-06-15

    Zinc oxide powders with six-sided flake-like particles were prepared by homogeneous precipitation from boiling aqueous solutions that contained excess urea and 0.075 (Z075) and 0.300 (Z300) M Zn{sup 2+}. The average sizes of the particles are 37 and 46 {mu}m, while the average sizes of the crystals are {approx}45 for Z075 and Z300 at 1000 deg. C. Equilibrium, kinetic and thermodynamic studies were carried out for the adsorption of RBBR dye from aqueous solution using both types of ZnO in the form of fine powders. The effects of pH, initial dye concentration, contact time and temperature of solution on the adsorption were studied. Langmuir, Temkin and Dubinin-Radushkevich (D-R) isotherm models were used to describe the adsorption of RBBR onto ZnO powders. The Langmuir and D-R isotherm models fit the equilibrium data better than the Temkin isotherm model. The monomolecular adsorption capacity of Z075 and Z300 was determined to be 190 and 345 mg g{sup -1} for RBBR, respectively. The Lagergren first-order, Ritchie second-order kinetic and intra-particle diffusion models were used for the adsorption of the dye onto ZnO powders. The Ritchie second-order model was suitable for describing the adsorption kinetics for the removal of RBBR from aqueous solution onto Z075 and Z300. Thermodynamic parameters, such as the Gibbs free energy ({Delta}G{sup numbersign}), enthalpy ({Delta}H{sup numbersign}), entropy ({Delta}S{sup numbersign}) and equilibrium constant of activation (K{sup numbersign}) were calculated. These parameters showed that the adsorption process of RBBR onto Z075 and Z300 was an endothermic process of a chemical nature under the studied conditions.

  19. Adsorption of Remazol Brilliant Blue R using ZnO fine powder: equilibrium, kinetic and thermodynamic modeling studies.

    Science.gov (United States)

    Ada, Kezban; Ergene, Aysun; Tan, Sema; Yalçin, Emine

    2009-06-15

    Zinc oxide powders with six-sided flake-like particles were prepared by homogeneous precipitation from boiling aqueous solutions that contained excess urea and 0.075 (Z075) and 0.300 (Z300)M Zn(2+). The average sizes of the particles are 37 and 46 microm, while the average sizes of the crystals are approximately 45 for Z075 and Z300 at 1000 degrees C. Equilibrium, kinetic and thermodynamic studies were carried out for the adsorption of RBBR dye from aqueous solution using both types of ZnO in the form of fine powders. The effects of pH, initial dye concentration, contact time and temperature of solution on the adsorption were studied. Langmuir, Temkin and Dubinin-Radushkevich (D-R) isotherm models were used to describe the adsorption of RBBR onto ZnO powders. The Langmuir and D-R isotherm models fit the equilibrium data better than the Temkin isotherm model. The monomolecular adsorption capacity of Z075 and Z300 was determined to be 190 and 345 mg g(-1) for RBBR, respectively. The Lagergren first-order, Ritchie second-order kinetic and intra-particle diffusion models were used for the adsorption of the dye onto ZnO powders. The Ritchie second-order model was suitable for describing the adsorption kinetics for the removal of RBBR from aqueous solution onto Z075 and Z300. Thermodynamic parameters, such as the Gibbs free energy (DeltaG(#)), enthalpy (DeltaH(#)), entropy (DeltaS(#)) and equilibrium constant of activation (K(#)) were calculated. These parameters showed that the adsorption process of RBBR onto Z075 and Z300 was an endothermic process of a chemical nature under the studied conditions.

  20. Effects of fine porosity on the fatigue behavior of a powder metallurgy superalloy

    Science.gov (United States)

    Miner, R. V.; Dreshfield, R. L.

    1980-01-01

    Hot-isostatically-pressed powder-metallurgy Astroloy was obtained which contained 1.4 percent porosity at the grain boundaries produced by argon entering the powder container during pressing. This material was tested at 650 C in fatigue, creep-fatigue, tension, and stress-rupture and the results compared with data on sound Astroloy. They influenced fatigue crack initiation and produced a more intergranular mode of propagation but fatigue life was not drastically reduced. Fatigue behavior of the porous material showed typical correlation with tensile behavior. The plastic strain range-life relation was reduced proportionately with the reduction in tensile ductility, but the elastic strain range-life relation was changed little.

  1. Hydrothermal synthesis of perovskite strontium doped lanthanum chromite fine powders and its sintering

    Energy Technology Data Exchange (ETDEWEB)

    Rendon-Angeles, J.C., E-mail: jcarlos.rendon@cinvestav.edu.m [Research Institute for Advanced Studies of the NPI, Campus-Saltillo, Ramos Arizpe 25900, Coah. (Mexico); Research Laboratory of Hydrothermal Chemistry, Kochi University, Kochi 780-8520 (Japan); Yanagisawa, K. [Research Laboratory of Hydrothermal Chemistry, Kochi University, Kochi 780-8520 (Japan); Matamoros-Veloza, Z. [Saltillo Institute of Technology, Dep. Metal-Mecanica, Saltillo 25820, Coah. (Mexico); Pech-Canul, M.I.; Mendez-Nonell, J. [Research Institute for Advanced Studies of the NPI, Campus-Saltillo, Ramos Arizpe 25900, Coah. (Mexico); Torre, S. Diaz-de la [Research Institute for Technology Innovation, CIITEC-IPN, Azcapotzalco 02250 (Mexico)

    2010-08-13

    Sr doped lanthanum chromite powders with two different compositions, La{sub 0.9}Sr{sub 0.1}CrO{sub 3} and La{sub 0.8}Sr{sub 0.2}CrO{sub 3}, were prepared from precursor lanthanum chromite gels obtained by the coprecipitation method, followed by hydrothermal treatments at temperatures from 400 to 450 {sup o}C, for various reaction times varying from 0.5 to 2 h. The reaction products were characterized by XRD, SEM and TEM techniques. The powder was cold isostatically pressed at 200 MPa, and then sintered in air at 1500 {sup o}C for several intervals (1-20 h). Relative density measurements were conducted by helium pycnometry and the microstructure was revealed by SEM after thermal etching. The X-ray diffraction patterns of the powders corresponding to La{sub 0.9}Sr{sub 0.1}CrO{sub 3} and La{sub 0.8}Sr{sub 0.2}CrO{sub 3} nominal compositions obtained at 400 and 425 {sup o}C for 1 h, respectively, were indexed with that of the orthorhombic single LaCrO{sub 3} phase. SEM and TEM micrographs showed that the particles had irregular peanut-like morphology, and the average particle size was 300 nm. Furthermore, the maximum relative density of the La{sub 0.8}Sr{sub 0.2}CrO{sub 3} sample obtained by the heat treatment in air at 1500 {sup o}C for 20 h was 97% of the theoretical density and the average grain size of the sintered pellet was of 5 {mu}m. The electric conductivity and activation energy determined for this pellet were 14477.3 S m{sup -1} and 0.13 eV, respectively.

  2. Comparative Study on Super Fine Mesophase Powder and MCMB Used to Manufacture High-Density Isotropic Carbon Bulks

    Institute of Scientific and Technical Information of China (English)

    LI Tong-qi; HU Zi-jun; WANG Jun-shan; GUO Yu-ming; WANG Cheng-yang

    2006-01-01

    Mesocarbon microbeads (MCMB) and super fine mesophase powder (SFMP) were prepared firstly from a coal tar pitch and then hot-condensed into high-density isotropic carbon (HDIC) bulks under 160 Mpa and finally sintered at 1 000 ℃. By analyzing the thermogravimetric behavior of the MCMB and SFMP powders, their volume shrinkage and weight loss during sintering and the bulk density and flexural strengths of their sintered bulks, it was found that the smaller sizes and the richer β-resin contents of SFMP have facilitated formation of sintered bulks with more compact isotropic structure and higher flexural strengths than MCMB. Because of the filling and bonding effects of SFMP on MCMB bulks, addition of SFMP, albeit a little, can greatly increase the flexural strengths of sintered bulks of MCMB. However, adding MCMB, even a slight amount, into SFMP can severely impair the flexural strength of sintered bulks. This might be attributed to both the crack initiation along the boundaries between MCMB and SFMP and the formation of layered texture of MCMB sphere.

  3. Preparation of ultra-fine powders from polysaccharide-coated solid lipid nanoparticles and nanostructured lipid carriers by innovative nano spray drying technology.

    Science.gov (United States)

    Wang, Taoran; Hu, Qiaobin; Zhou, Mingyong; Xue, Jingyi; Luo, Yangchao

    2016-09-10

    In this study, five polysaccharides were applied as natural polymeric coating materials to prepare solid lipid nanoparticles (SLN) and nanostructure lipid carriers (NLC), and then the obtained lipid colloidal particles were transformed to solid powders by the innovative nano spray drying technology. The feasibility and suitability of this new technology to generate ultra-fine lipid powder particles were evaluated and the formulation was optimized. The spray dried SLN powder exhibited the aggregated and irregular shape and dimension, but small, uniform, well-separated spherical powder particles of was obtained from NLC. The optimal formulation of NLC was prepared by a 20-30% oleic acid content with carrageenan or pectin as coating material. Therefore, nano spray drying technology has a potential application to produce uniform, spherical, and sub-microscale lipid powder particles when the formulation of lipid delivery system is appropriately designed. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Performance of a Venturi scrubber in the removal of fine powder from a confined gas stream

    Directory of Open Access Journals (Sweden)

    Maria Angélica Martins Costa

    2005-06-01

    Full Text Available Experimental results on the performance of a laboratory scale rectangular Venturi scrubber in the removal of fine mineral particles from a confined air stream are presented, and a new correlation is proposed and evaluated. The scrubber was operated with air velocities in the throat varying from 58 m/s to 75 m/s and liquid flow rates varying from 280 ml/min to 900 ml/min. Liquid was injected as a jet emerging from a 1.0 mm orifice at the throat. Results for dust collection grade efficiency varied from 87% to 98% for particles from 0.1 µm to 2.0 µm.

  5. FLOW PROPERTIES OF COHESIVE NANOPOWDERS

    Institute of Scientific and Technical Information of China (English)

    Jürgen Tomas

    2003-01-01

    The fundamentals of cohesive powder consolidation and flow behaviour using a reasonable combination of particle and continuum mechanics are explained. By means of the model "stiff particles with soft contacts", the influence of elastic-plastic repulsion in particle contacts is demonstrated. With this as the physical basis, the stationary yield locus, instantaneous yield loci and consolidation loci, flow function and compression function are presented. The flow properties of a very cohesive titania nanopowder (ds=200 nm) are shown. These models ara used to evaluate shear cell test results as constitutive functions for computer aided apparatus design for reliable powder flow.

  6. Scaling forces to asteroid surfaces: The role of cohesion

    CERN Document Server

    Scheeres, D J; Sanchez, P; Swift, M

    2010-01-01

    The scaling of physical forces to the extremely low ambient gravitational acceleration regimes found on the surfaces of small asteroids is performed. Resulting from this, it is found that van der Waals cohesive forces between regolith grains on asteroid surfaces should be a dominant force and compete with particle weights and be greater, in general, than electrostatic and solar radiation pressure forces. Based on this scaling, we interpret previous experiments performed on cohesive powders in the terrestrial environment as being relevant for the understanding of processes on asteroid surfaces. The implications of these terrestrial experiments for interpreting observations of asteroid surfaces and macro-porosity are considered, and yield interpretations that differ from previously assumed processes for these environments. Based on this understanding, we propose a new model for the end state of small, rapidly rotating asteroids which allows them to be comprised of relatively fine regolith grains held together b...

  7. Development of spherical fine powders by high-pressure water atomization using swirl water jet; Senkaisui jet wo mochiita koatsusui atomize ni yoru kyujo bifun no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kikukawa, M.; Matsumoto, S.; Inaba, T.; Iwatsu, O.; Takeda, T. [Fukuda Metal Foil and Powder Co. Ltd., Kyoto (Japan)

    2000-05-15

    In order to obtain spherical fine powders, a new high-pressure water atomization method using swirl water jet was developed. In this paper the effects of jet swirl angle ({omega}) upon the properties of powders were investigated. Cu-10 mass%Sn alloy was atomized by this method at the constant water pressure of 83.3 MPa and constant metal orifice diameter of 4mm, while {omega} was varied from 0 to 0.18 rad. Median diameter of the powder by the laser diffraction method (D{sub 50}) decreased from 12.5 {mu}m to 7.5{mu}m with increasing {omega}, and this corresponded to Fisher average diameter (D{sub FS}) at about w=0.18 rad. The apparent and tap density of the powder increased about 1 and 1.5 Mg/m{sup 3} respectively, and the particle shape observed by SEM became spherical with increasing {omega}. (author)

  8. Preparation of active proteins, vaccines and pharmaceuticals as fine powders using supercritical or near-critical fluids.

    Science.gov (United States)

    Cape, Stephen P; Villa, Joseph A; Huang, Edward T S; Yang, Tzung-Horng; Carpenter, John F; Sievers, Robert E

    2008-09-01

    Supercritical or near-critical fluid processes for generating microparticles have enjoyed considerable attention in the past decade or so, with good success for substances soluble in supercritical fluids or organic solvents. In this review, we survey their application to the production of protein particles. A recently developed process known as CO2-assisted nebulization with a Bubble Dryer (CAN-BD) has been demonstrated to have broad applicability to small-molecule as well as macromolecule substances (including therapeutic proteins). The principles of CAN-BD are discussed as well as the stabilization, micronization and drying of a wide variety of materials. More detailed case studies are presented for three proteins, two of which are of therapeutic interest: anti-CD4 antibody (rheumatoid arthritis), alpha1-antitrypsin (cystic fibrosis and emphysema), and trypsinogen (a model enzyme). Dry powders were formed in which stability and activity are maintained and which are fine enough to be inhaled and reach the deep lung. Enhancement of apparent activity after CAN-BD processing was also observed in some formulation and processing conditions.

  9. Design of sustained release fine particles using two-step mechanical powder processing: particle shape modification of drug crystals and dry particle coating with polymer nanoparticle agglomerate.

    Science.gov (United States)

    Kondo, Keita; Ito, Natsuki; Niwa, Toshiyuki; Danjo, Kazumi

    2013-09-10

    We attempted to prepare sustained release fine particles using a two-step mechanical powder processing method; particle-shape modification and dry particle coating. First, particle shape of bulk drug was modified by mechanical treatment to yield drug crystals suitable for the coating process. Drug crystals became more rounded with increasing rotation speed, which demonstrates that powerful mechanical stress yields spherical drug crystals with narrow size distribution. This process is the result of destruction, granulation and refinement of drug crystals. Second, the modified drug particles and polymer coating powder were mechanically treated to prepare composite particles. Polymer nanoparticle agglomerate obtained by drying poly(meth)acrylate aqueous dispersion was used as a coating powder. The porous nanoparticle agglomerate has superior coating performance, because it is completely deagglomerated under mechanical stress to form fine fragments that act as guest particles. As a result, spherical drug crystals treated with porous agglomerate were effectively coated by poly(meth)acrylate powder, showing sustained release after curing. From these findings, particle-shape modification of drug crystals and dry particle coating with nanoparticle agglomerate using a mechanical powder processor is expected as an innovative technique for preparing controlled-release coated particles having high drug content and size smaller than 100 μm.

  10. Additive Manufacturing/Diagnostics via the High Frequency Induction Heating of Metal Powders: The Determination of the Power Transfer Factor for Fine Metallic Spheres

    Energy Technology Data Exchange (ETDEWEB)

    Rios, Orlando [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Radhakrishnan, Balasubramaniam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Caravias, George [Grid Logic, Inc., Lapeer, MI (United States); Holcomb, Matthew [Grid Logic, Inc., Lapeer, MI (United States)

    2015-03-11

    Grid Logic Inc. is developing a method for sintering and melting fine metallic powders for additive manufacturing using spatially-compact, high-frequency magnetic fields called Micro-Induction Sintering (MIS). One of the challenges in advancing MIS technology for additive manufacturing is in understanding the power transfer to the particles in a powder bed. This knowledge is important to achieving efficient power transfer, control, and selective particle heating during the MIS process needed for commercialization of the technology. The project s work provided a rigorous physics-based model for induction heating of fine spherical particles as a function of frequency and particle size. This simulation improved upon Grid Logic s earlier models and provides guidance that will make the MIS technology more effective. The project model will be incorporated into Grid Logic s power control circuit of the MIS 3D printer product and its diagnostics technology to optimize the sintering process for part quality and energy efficiency.

  11. A study on preparation of PTFE fine powder from its dispersions%从聚四氟乙烯分散液制备微粉的研究

    Institute of Scientific and Technical Information of China (English)

    龚天龙; 余自力

    2014-01-01

    Polytetrafluoroethylene( PTFE) fine powder was prepared from its dispersions by destroying the pH balance. The obtained PTFE fine powder was found to have molecular weight in the order of 107 ,median diameter D50 of 25 μm,and has the same struc-ture as commercial PTFE.%本文以聚四氟乙烯( PTFE)分散液(乳液)为原料,利用破坏其酸碱平衡的原理,成功地制备了PTFE微粉。所得到PTFE微粉分子量达到107数量级,中值粒径D50为25μm,树脂结构与PTFE一致。

  12. Evaluation of the behavior of ceramic powders under mechanical vibration and its effect on the mechanics of auto-granulation

    Science.gov (United States)

    Ku, Nicholas

    In ceramic powder processing, the correlations between the constituent particles and the product structure-property outcomes are well established. However, the influence of static powder properties on the dynamic bulk powder behavior in such advance powder processes remains elusive. A multi-scale evaluation is necessary to understand the full effects of the particle ensemble on the bulk powder behavior, ranging from the particle micro-scale to the bulk powder macro-scale. Fine powders, with particle size of 10 ?m or less, often exhibit cohesive behavior. Cohesion in powders can cause poor flowability, affect agglomerate formation, as well as induce powder caking, all of which can be detrimental to the processing of the powders and/or final product structure-property outcomes. For this reason, it is critical to correlate the causal properties of the powders to this detrimental behavior. In this study, the bulk behavior of ceramic powders is observed under a simple powder process: harmonic, mechanical vibration. Four powder samples, two titania and two alumina powders, were studied. The main difference between the two powder variants of each material is particle size. The two alumina (Al2O3) powder samples had a primary particle size at 50% less than, or d50 of, 0.5 and 2.3 microm and the titania (TiO2) powder samples had a d 50 particle size of 0.1 and 1 microm. Due to mechanical vibration, the titania powder variant with a primary particle size of 0.1 microm exhibited a clustering behavior known as auto-granulation. Auto-granulation is the growth of particle clusters within a dry, fine powder bed without the addition of any binder or liquid to the system. The amplitude and frequency of the mechanical vibration was varied to view the effect on the equilibrium granule size and density. Furthermore, imaging of cross-sections of the granules was conducted to provide insight into to the internal microstructure and measure the packing fraction of the constituent

  13. Flocculation Dynamics of cohesive sediment

    NARCIS (Netherlands)

    Maggi, F.

    2005-01-01

    Cohesive sediment suspended in natural waters is subject not only to transport and deposition processes but also to reactions of flocculation, \\textit{i.e.} aggregation of fine particles, and breakup of aggregates. Although aggregation and breakup occur at small and very small length scales compared

  14. Preparation of fine-grained tungsten heavy alloys by spark plasma sintered W–7Ni–3Fe composite powders with different ball milling time

    Energy Technology Data Exchange (ETDEWEB)

    Xiang, D.P., E-mail: dpxiang@hainu.edu.cn [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Ding, L. [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China); Li, Y.Y.; Chen, G.B. [School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Zhao, Y.W. [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China)

    2013-06-15

    Highlights: ► We fabricate fine-grained W–7Ni–3Fe alloys using HEBM assisted SPS method. ► The γ-(Ni, Fe, W) phase is not observed in HEBM raw powders. ► The density of the WHAs gradually decreased with increasing HEBM time. ► The hardness and bending strength of the WHAs show different trends of variation. ► The intergranular fracture was the main bending fracture mode of the WHAs. -- Abstract: The fine-grained tungsten heavy alloys (WHAs) with grain size of about 1–3 μm were successfully prepared by spark plasma sintered W–7Ni–3Fe composite powders with different high-energy ball milling (HEBM) time. This study analyzes the effects of HEBM time not only on the composite powders but on the microstructure and mechanical properties of WHAs. The scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to investigate the microstructure and phase evolution rules of powders and alloys, respectively. The γ-(Ni, Fe, W) is not observed in XRD patterns of the ball milled powders. With prolonging HEBM time, the W phase diffraction peak becomes increasingly wider, and its intensity continues to decline. However, the completely amorphous structures are not formed even after HEBM 40 h. The relative density of the WHAs prepared by HEBM assisted SPS technique decreases gradually with increasing the ball milling time. For the WHAs sintered in 1150 °C for 8 min, the W grains grow finer and the content of the γ-(Ni, Fe, W) binding phase greatly increases with prolonging the HEBM time. Meanwhile, over 5 h of HEBM time, the bending strength continuously decreases and the hardness slightly increases. The intergranular fracture of the W grains is the main bending fracture mode in all the WHAs. The microporous of different sizes are distributed on the bending fracture and progressively increased with prolonging the ball milling time.

  15. Understanding Cohesion in English

    OpenAIRE

    Shibayama, Morijiro

    1981-01-01

    Cohesion is Hasan's term. The concept of cohesion, however, is not well-formed and its mechanism is still to be studied. In this paper, the author says: 1. Both cohesion and a tie are semantic concepts. 2. Cohesion in a text is a set of ties between sentences. Based on the definitions, the author discusses the formal and lexicogrammatical factors which generate cohesion.

  16. Colossal negative thermal expansion with an extended temperature interval covering room temperature in fine-powdered Mn0.98CoGe

    Science.gov (United States)

    Lin, Jianchao; Tong, Peng; Zhang, Kui; Tong, Haiyun; Guo, Xinge; Yang, Cheng; Wu, Ying; Wang, Meng; Lin, Shuai; Chen, Li; Song, Wenhai; Sun, Yuping

    2016-12-01

    MnM'X (M' = Co, Ni; X = Ge, Si, etc.) alloys usually present a large volumetric change during the Martensitic (MA) transformation. This offers a great opportunity for exploring new negative thermal expansion (NTE) materials if the temperature interval of NTE can be extended. Here, we report colossal NTE in fine-powdered Mn0.98CoGe prepared by repeated thermal cycling (TC) through the MA transition or ball milling. Both treatments can expand the MA transformation, and thus broaden the NTE temperature window (ΔT). For the powders that have gone through TC for ten times, ΔT reaches 90 K (309 K-399 K), and the linear expansion coefficient (αL) is about -141 ppm/K, which rank among the largest values of colossal NTE materials. The difference between two kinds of treatments and the possible mechanisms of the extended MA transformation window are discussed based on the introduced strain.

  17. Normal and abnormal grain growth in fine-grained Nd-Fe-B sintered magnets prepared from He jet milled powders

    Science.gov (United States)

    Bittner, F.; Woodcock, T. G.; Schultz, L.; Schwöbel, C.; Gutfleisch, O.; Zickler, G. A.; Fidler, J.; Üstüner, K.; Katter, M.

    2017-03-01

    Fine-grained, heavy rare earth free Nd-Fe-B sintered magnets were prepared from He jet milled powders with an average particle size of 1.5 μm by low temperature sintering at 920 °C or 980 °C. A coercivity of >1600 kA/m was achieved for an average grain size of 1.68 μm. Transmission electron microscopy showed that the distribution and composition of intergranular and grain boundary junction phases was similar to that in conventionally processed magnets. Microstructural analysis on different length scales revealed the occurrence of abnormal grain growth, which is unexpected for sintering temperatures below 1000 °C. A larger area fraction of abnormal grains was observed in the sample sintered at 920 °C compared to that sintered at 980 °C. Microtexture investigation showed a better crystallographic alignment of the abnormal grains compared to the fine-grained matrix, which is explained by a size dependent alignment of the powder particles during magnetic field alignment prior to sintering. Slightly larger particles in the initial powder show a better alignment and will act as nucleation sites for abnormal grain growth. Magneto-optical Kerr investigations confirmed the lower switching field of the abnormal grains compared to the fine-grained matrix. The demagnetisation curve of the sample sintered at 920 °C showed reduced rectangularity and this was attributed to a cooperative effect of the larger fraction of abnormal grains with low switching field and, as a minor effect, a reduced degree of crystallographic texture in this sample compared to the material sintered at 980 °C, which did not show the reduced rectangularity of the demagnetisation curve.

  18. Fine-sized LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders prepared by combined process of gas-phase reaction and solid-state reaction methods

    Science.gov (United States)

    Ju, Seo Hee; Kang, Yun Chan

    The Ni-rich precursor powders with spherical shape and filled morphologies were prepared by spray pyrolysis from the spray solution with citric acid, ethylene glycol and a drying control chemical additive. The precursor powders with controlled morphologies formed the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders with spherical shape and fine size by solid-state reaction with lithium hydroxide. However, the cathode powders prepared from the spray solution without additives had irregular morphologies and were large in size. The precursor powders with hollow and porous morphologies formed cathode powders with irregular and aggregated morphologies. The composition ratios of the nickel, cobalt and manganese components were maintained in the as-prepared, precursor and cathode powders. The initial discharge capacity of the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders with spherical shape and fine size tested at a temperature of 55 °C under a constant current density of 0.5 C was 215 mAh g -1. The discharge capacity of the LiNi 0.8Co 0.15Mn 0.05O 2 cathode powders decreased to 81% of the initial value after 30 cycles.

  19. Evaluation of the degree of mixing of combinations of dry syrup, powder, and fine granule products in consideration of particle size distribution using near infrared spectrometry.

    Science.gov (United States)

    Yamamoto, Yoshihisa; Suzuki, Toyofumi; Matsumoto, Mika; Ohtani, Michiteru; Hayano, Shuichi; Fukami, Toshiro; Tomono, Kazuo

    2012-01-01

    We used near infrared (NIR) spectroscopy to evaluate the degree of mixing of blended dry syrup (DS) products whose particle sizes are not specified in the Revised 16th Edition of the Japanese Pharmacopoeia, and also evaluated the degree of mixing when powder products or fine granule products were added to DS products. The data obtained were used to investigate the relationship between the particle size distributions of the products studied and the degree of mixing. We found that the particle size distribution characteristics of the 15 DS products studied can be broadly classified into 5 types. Combinations of frequently prescribed products were selected to represent 4 of the 5 particle size distribution types and were blended with a mortar and pestle. The coefficient of variation (CV) decreased as the percent mass of Asverin® Dry Syrup 2% (Asverin-DS) increased in blends of Periactin® Powder 1% (Periactin) and Asverin-DS, indicating an improved degree of mixing (uniformity). In contrast, in blends of Periactin and Mucodyne® DS 33.3%, mixing a combination at a 1:1 mass ratio 40 times resulted in a CV of 20%. Other mixing frequencies and mass ratios resulted in a CV by 50% to 70%, indicating a very poor degree of mixing (poor uniformity). These results suggest that when combining different DSs, or a DS with a powder or fine granule product, the blending obtained with a mortar and pestle improves as the particle size distributions of the components approach each other and as the ranges of the distributions narrow.

  20. Magnetic properties of TCr{sub 2}O{sub 4} (T = Co, Ni) fine powders and TCr{sub 2}O{sub 4}/SiO{sub 2} nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Mantlikova, Alice; Vejpravova, Jana Poltierova [Department of Condensed Matter Physics, Faculty of Mathematics and Physics, Charles university, Prague (Czech Republic); Holec, Petr; Niznansky, Daniel [Department of Inorganic Chemistry, Faculty of Nature Science, Charles university, Prague (Czech Republic); Plocek, Jiri, E-mail: AliceMantlikova@seznam.cz [Institute of Inorganic Chemistry, Academy of science of the CR, Husinec-Rez (Czech Republic)

    2011-10-29

    We have studied magnetic properties of TCr{sub 2}O{sub 4} (T = Co, Ni) fine powders, obtained by the citric acid method, and TCr{sub 2}O{sub 4}/SiO{sub 2} nanocomposites, constituted of spinel nanoparticles embedded in silica matrix fabricated by a modified sol gel method. All samples were characterized by powder X-ray diffraction, scanning electron microscopy and microprobe analysis. The profile analysis of the powder X-ray diffraction revealed that the particle size is larger for the fine powder samples, as expected. Detailed measurements of magnetization, hysteresis loops and a.c. susceptibility demonstrate significant differences in magnetic properties of the fine powders in comparison to the nanocomposite samples. The values of the coercitivity at 10 K ranges from {approx} 2T for NiCr{sub 2}O{sub 4} fine powders to {approx} 0.6 T for CoCr{sub 2}O{sub 4}/SiO{sub 2} nanocomposites. Moreover, the hysteresis loops of the NiCr{sub 2}O{sub 4}/SiO{sub 2} samples are brightly asymmetric. The phenomenon will be discussed in context of the exchange-bias originated by presence of a tiny amount of the antiferromagnetic phase, Cr{sub 2}O{sub 3} in the samples.

  1. The Research Description of the Large Quantity of Mineral Fine Powder of RPC%大掺量矿物微细粉活性粉末混凝土的研究综述

    Institute of Scientific and Technical Information of China (English)

    谢彪

    2014-01-01

    Large quantity of mineral fine powder reactive powder concrete sets the advantages of high strength concrete and fiber reinforced concrete, and has the characteristics of super-high strength, low brittleness and high durability. This paper expounded its preparation principle, summarized and prospected its application status and prospects, and finally put forward problems existing in the actual application of large quantity of mineral fine powder reactive powder concrete, which provides some new thoughts for the research and application of large quantity of mineral fine powder reactive powder concrete.%大掺量矿物微细粉活性粉末混凝土集高强混凝土和纤维混凝土的优势于一体,具有超高强、低脆性、高耐久性的特点,本文对其制备原理进行阐述,并对其应用现状和前景进行概述和展望,最后提出目前应用大掺量矿物微细粉活性粉末混凝土实际中存在的问题。为大掺量矿物微细粉活性粉末混凝土的研究应用提供一些新的思路。

  2. Radiation-induced copolymerization of styrene/ n-butyl acrylate in the presence of ultra-fine powdered styrene-butadiene rubber

    Science.gov (United States)

    Yu, Haibo; Peng, Jing; Zhai, Maolin; Li, Jiuqiang; Wei, Genshuan; Qiao, Jinliang

    2007-11-01

    Styrene (St)/ n-butyl acrylate (BA) copolymers were prepared by two-stage polymerization: St/BA was pre-polymerized to a viscous state by bulk polymerization with initiation by benzoyl peroxide (BPO) followed by 60Co γ-ray radiation curing. The resultant copolymers had higher molecular weight and narrower molecular weight distribution than conventional methods. After incorporation of ultra-fine powdered styrene-butadiene rubber (UFSBR) with a particle size of 100 nm in the monomer, the glass transition temperature ( Tg) of St-BA copolymer increased at low rubber content. Both the St-BA copolymer and the St-BA copolymer/UFSBR composites had good transparency at BA content below 40%.

  3. Non-steroidal anti-inflammatory drug for pulmonary administration: design and investigation of ketoprofen lysinate fine dry powders.

    Science.gov (United States)

    Stigliani, Mariateresa; Aquino, Rita P; Del Gaudio, Pasquale; Mencherini, Teresa; Sansone, Francesca; Russo, Paola

    2013-05-01

    Pulmonary inflammation is an important therapeutic target in cystic fibrosis (CF) patients, aiming to limit and delay the lung damage. The purpose of the present research was to produce respirable engineered particles of ketoprofen lysinate, a non-steroidal anti-inflammatory drug able to fight lung inflammatory status by direct administration to the site of action. Micronized drug powders containing leucine as dispersibility enhancer were prepared by co-spray drying the active compound and the excipient from water or hydro-alcoholic feeds. Microparticles were fully characterized in terms of process yield, particle size distribution, morphology and drug content. The ability of the drug to reach the deepest airways after aerosolization of spray-dried formulations was evaluated by Andersen cascade impactor, using the monodose DPI as device. In order to investigate the behaviour of the drug once in contact with lung fluid, an artificial CF mucus was prepared. Drug permeation properties were evaluated interposing the mucus layer between the drug and a synthetic membrane mounted in Franz-type diffusion cells. Finally, the effect of the engineered particles on vitality of human airway epithelial cells of patients homozygous for ΔF 508 CF (CuFi1) was studied and compared to that of raw active compound. Results indicated that powders engineering changed the diameter and shape of the particles, making them suitable for inhalation. The mucus layer in the donor compartment of vertical diffusion cells slowed down drug dissolution and permeation, leucine having no influence. Cell proliferation studies evidenced that the spray drying process together with the addition of leucine reduced the cytotoxic effect of ketoprofen lysine salt as raw material, making the ketoprofen lysinate DPI a very promising product for the inflammation control in CF patients.

  4. Biaxially textured articles formed by powder metallurgy

    Science.gov (United States)

    Goyal, Amit; Williams, Robert K.; Kroeger, Donald M.

    2003-07-29

    A biaxially textured alloy article having a magnetism less than pure Ni includes a rolled and annealed compacted and sintered powder-metallurgy preform article, the preform article having been formed from a powder mixture selected from the group of mixtures consisting of: at least 60 at % Ni powder and at least one of Cr powder, W powder, V powder, Mo powder, Cu powder, Al powder, Ce powder, YSZ powder, Y powder, Mg powder, and RE powder; the article having a fine and homogeneous grain structure; and having a dominant cube oriented {100} orientation texture; and further having a Curie temperature less than that of pure Ni.

  5. Th uptake on montmorillonite: a powder and polarized extended X-ray absorption fine structure (EXAFS) study.

    Science.gov (United States)

    Dähn, Rainer; Scheidegger, André M; Manceau, Alain; Curti, Enzo; Baeyens, Bart; Bradbury, Michael H; Chateigner, Daniel

    2002-05-01

    The uptake process of Th(IV) onto montmorillonite was studied using powder and polarized-EXAFS (P-EXAFS) spectroscopy. Sorption samples were prepared in 0.1 M NaClO(4) solutions either undersaturated (pH 2 and 3, [Th](initial): 2.7x10(-6) to 4x10(-4) M) or supersatured (pH 5, [Th](initial): 4.3x10(-5) to 4x10(-4) M) with respect to amorphous ThO(2). Th loading varied between 1-157 micromol/g at pH 3 and 14-166 micromol/g at pH 5 and equaled 41 micromol/g at pH 2. At pH 5 and high surface loading the EXAFS spectrum resembled that of amorphous Th(OH)(4), suggesting the precipitation of a Th hydrous hydroxide. At low and intermediate surface coverage two O coordination shells at approximately 2.24 and approximately 2.48 A, and one Si shell at 3.81-3.88 A, were systematically observed regardless of pH. The formation of Th nucleation products and Th-Si solution complexes and the sorption of Th on a silica precipitate were excluded from the EXAFS spectra analysis and solution chemistry. In these conditions, Th was shown to bond the montmorillonite surface by sharing double corners with Si tetrahedra. This structural interpretation is consistent with surface coverage calculations which showed that the edge sites were saturated in the two highest concentrated samples (34 and 157 micromol/g) at pH 3.

  6. Electromagnetic wave absorption properties of Fe{sub 73}Si{sub 16}B{sub 7}Nb{sub 3}Cu{sub 1}-based composites mixed with fine charcoal powder

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sun-I; Kim, Mi Rae; Sohn, Keun Yong; Park, Won-Wook, E-mail: wwpark@inje.ac.k [Department of Nano-Systems Engineering, Inje University, 607 Obang-dong, Gimhae, Gyeongnam 621-749 (Korea, Republic of)

    2010-05-01

    Fe{sub 73}Si{sub 16}B{sub 7}Nb{sub 3}Cu{sub 1} soft magnetic powder was crystallized to obtain a nano grain structure and mixed with a fine charcoal powder. The mixtures were tape-cast with polymer-based organic binders to form a sheet-type electromagnetic (EM) wave absorption composite. The EM wave absorption properties of the sheets were investigated using a network analyzer. The results showed that addition of charcoal powder improved the EM-absorbing properties of the composite. The power loss of the EM wave was directly related to the imaginary part of the permeability and permittivity, and it was reviewed in detail. Excellent absorption properties were achieved by adding 5 wt % charcoal powder (-500 mesh) to the Fe-based sheets.

  7. Powder lubrication of faults by powder rolls in gouge zones

    Science.gov (United States)

    Chen, X.; Madden, A. S.; Reches, Z.

    2013-12-01

    Powder-lubrication by fault gouge can be an effective mechanism of dynamic weakening of faults (Reches & Lockner, 2010); however, the physical mechanisms of this lubrication are poorly understood. While the flow of coarse-grained (> 100 μm) materials, e.g. glass beads or quartz sand, was extensively studied, the flow of fine-grained (nano-powders, have remained enigmatic. We report here experimental results of a new efficient mechanism for powder lubrication. We conducted friction tests on high-velocity rotary shear apparatus (Reches & Lockner, 2010). Two types of experimental faults were tested: (1) faults made of solid, igneous rocks (granite, tonalite and diorite); and (2) fault-zones made of 2-3 mm thick layer of granular materials (oolites, calcite or gypsum) sheared in a confined cell. We performed 21 runs with total slip of 0.14-13 m, normal stress of 1.2-14.5 MPa, slip velocity of 0.012-0.97 m/s. The ultra-microscopic (SEM and AFM) analysis of the experimental slip surfaces revealed two outstanding features in 17 out of the 21 experiments: (1) localized fault-slip along Principal Slip Zones (PSZs) that are composed of a dense, shiny, cohesive crust, 0.5-1 micron thick, that overlaid a porous substrate, and (2) elongated rolls composed of gouge-powder into three-dimensional structures of closely-packed powder grains, (20-50 nm in size). The rolls are cylindrical, 0.75-1.4 micron wide, and 1.7-30 micron long, with smooth outer surface, and laminated, concentric layers of compacted grains. The rolls were exclusively found on the PSZs. Many rolls were destroyed fracturing and smearing on the PSZ, suggesting that the rolls underwent a life cycle of formation and destruction. Significant macroscopic friction reduction was measured in experiments with observed rolls, and no (or minor) friction reduction in the four experiments without rolls. The final, reduced friction coefficients have a general reciprocal relation to the rolls surface coverage, suggesting that

  8. Preparation of Ni-Cr overlay weld alloy with finely dispersed NbC particles from (Ni-Cr)/NbC composite powder. Fukugo funmatsu wo mochiita bisai NbC ryushi bunsan Ni-Cr nikumori gokin no sakusei

    Energy Technology Data Exchange (ETDEWEB)

    Tomita, T.; Takatani, Y. (Hyogo Prefectural Inst. of Industrial Research, Hyogo (Japan)); Harada, Y.; Nagai, K. (Tocalo Co. Ltd., Kobe (Japan))

    1992-11-20

    In previous studies, Ni-Cr overlay alloy containing NbC particles, formed by the plasma powder welding process, was found to exhibit excellent wear and corrosion resistances. However, any overlay alloy with dispersed NbC particles having a diameter below a few micron, has not been yet obtained. In this study, a composite powder was prepared by compounding 40 vol.% of NbC powder having an average grain diameter of 1.3 [mu]m into Ni-50 mass% Cr alloy powder, and then mixing, granulating and sintering. Plasma powder weddings were carried out on a mild steel plate using this complex powder, and the effect of plasma arc current on melting of complex powder particles and dispersion behavior of NbC particles was studied by structure observation and X-ray diffractometry. As a result, it was clarified that by selecting the proper plasma arc current and controlling the heat input, uniform dispersion of fine NbC particles having a diameter of a few micron into the matrix was possible. 18 refs., 8 figs., 3 tabs.

  9. High-performance resin-bonded magnets produced from zinc metal-coated Sm2(Fe0.9Co0.1)17Nx fine powders

    Science.gov (United States)

    Noguchi, K.; Machida, K.; Yamamoto, K.; Nishimura, M.; Adachi, G.

    1999-09-01

    Fine powders of Sm2(Fe0.9Co0.1)17Nx (x=˜3) with particle sizes (d) around 1 μm as coated with zinc metal produced via the photodecomposition of diethylzinc [Zn(C2H5)2], which still provided high remanence (Br) and coercivity (Hcj) values of ˜1.43 T and ˜0.85 MAm-1, were molded to compression-type resin bonded Zn/Sm2(Fe0.9Co0.1)17Nx magnets with density values of ˜6.33 g cm-3. By optimizing the preparation conditions such as grinding, surface coating, and molding for them, the highest maximum energy product of (BH)max=186 kJm-3 for Hcj=0.73 MAm-1 was recorded among all kinds of the Sm-Fe-N based magnets reported to date. Furthermore, the excellent aging behavior of the bonded Zn/Sm2(Fe0.9Co0.1)17Nx magnets was observed after standing in air at ˜393 K and the thermal coefficient for permanent magnet was evaluated to be α(Br)=-0.04% K-1.

  10. Research on Turmeric Fine Pulverizing Process and Its Powder Properties%郁金微细粉碎工艺及其微细粉的粉体学性质研究

    Institute of Scientific and Technical Information of China (English)

    郝月莆; 秦春凤; 向孙敏; 杨安东; 逯多

    2014-01-01

    目的:对郁金微细粉碎工艺及粉碎过后的郁金微细粉的粉体学性质进行研究分析,为郁金作为中药制剂原料药使用提供依据。方法:以d50为指标,运用正交设计优选郁金的微细粉碎工艺,并通过微细粉碎前后外观性状、红外光谱、流动性、吸湿性等方面进行比较研究,评价不同粒径郁金粉体的粉体学性质。结果:根据正交设计结果优选出了最佳微细粉碎工艺,即投料量为1200 g、含水量为5.5%、粉碎时间为40 min;郁金超微前后粉末的粉体学性质对比结果显示,随粒径变小,郁金粉体逐渐出现团聚现象,颗粒感消失,颜色变浅,粉末细腻,化学成分和分子结构未发生改变,流动性降低,平衡吸湿量增加,吸湿初始速度增大,但吸湿加速度降低,吸湿性略增强。结论:郁金微细粉碎工艺简便,可靠,粒径小,可行性高,可用于郁金的微细粉碎,综合评价优选微细粉四为较优粉体。%This paper was aimed to analyze and study the process of Turmeric fine pulverizing; and the powder properties of Turmeric ultra-micro powder after the process. Based on d50, the powder properties of Turmeric ultra-micro powder were summarized by using orthogonal design to select the optimal Turmeric fine pulverizing. Compari-sons were made on powder properties, such as exterior characters, IR spectra, fluidity and hygroscopicity before and after fine pulverizing. The results showed that optimal fine pulverizing process was determined based on orthogonal design. The conditions were that the material was 1 200 g, with water of 5.5% and crushing for 40 min. Compari-son of powder properties of Turmeric powders before and after fine pulverizing showed that as the diameter of the particle decreased. Turmeric particle gradually showed signs of aggregation. At the same time, granular sensation disappeared;the color turned lighter;powder became finer

  11. Adhesion forces in interactive mixtures for dry powder inhalers--evaluation of a new measuring method.

    Science.gov (United States)

    Lohrmann, Maike; Kappl, Michael; Butt, Hans-Juergen; Urbanetz, Nora Anne; Lippold, Bernhard Christian

    2007-09-01

    Dry powder inhalers mostly contain carrier based formulations where micronized drug particles are adhered to coarse carrier particles. The performance of the dry powder inhaler depends on the inhaler device, the inhalation manoeuvre and the formulation. The most important factor influencing the behaviour of the formulation is the adhesion force acting between the active ingredient and the carrier particles, which can be measured using different methods, for example the centrifuge technique or atomic force microscopy. In this study the tensile strength method, usually applied to determine cohesion forces between powder particles of one material, is optimized for adhesion force measurements between powder particles of unlike materials. Adhesion force measurements between the carrier materials lactose or mannitol and the drug substance salbutamol sulphate using the tensile strength method and the atomic force microscopy show higher values with increasing relative humidity. Consequently, the fine particle fraction determined using the Next Generation Impactor decreases with increasing relative humidity as a result of the enhanced interparticle interactions.

  12. Dynamics of Cohesive Sediments

    DEFF Research Database (Denmark)

    Johansen, Claus

    the nature of the cohesive sediment with respect to the transport processes is presented. In addition, the flocculation process and the rheological behaviour of cohesive sediments is outlined. The second part contains the laboratory experiments. The laboratory experiments were conducted with respect......The present thesis considers the transport processes of cohesive sediments. The cohesive sediment used in the laboratory experiments was kaolinite, a clay mineral, in order to be able to reproduce the individual experiments. In the first part of the thesis, the theoretical considerations regarding...

  13. Traversing the Lexical Cohesion Minefield

    Science.gov (United States)

    McGee, Iain

    2009-01-01

    When teachers hear the word "cohesion", they usually think of grammatical cohesion--an aspect of cohesion reasonably well covered in student books and teacher materials. However, occupying an area that straddles both lexis "proper" and cohesion lies "lexical cohesion". In what follows, it is argued that the teaching and learning of certain aspects…

  14. Diversity and Social Cohesion

    Science.gov (United States)

    Pagani, Camilla

    2014-01-01

    The issue of diversity, in its broadest sense, is discussed here in its relation to social cohesion, cross-cultural relations, ingroup-outgroup relations and educational interventions. The main thesis of the paper is that real social cohesion in an ingroup rests on the acknowledgment of and the dialog with the diversities of the members of the…

  15. Social cohesion in Europe

    NARCIS (Netherlands)

    Reverda, Nol

    2010-01-01

    This chapter explores the current discussions and policies towards social exclusion and cohesion in Europe. In a first section will briefly be identified how the wording in the social work discourse changed from originally the thinking in terms of poverty to the ideas of social cohesion nowadays. Th

  16. INDICATORS OF TERRITORIAL COHESION

    Directory of Open Access Journals (Sweden)

    MARIA VASILESCU (DUMITRASCU

    2014-12-01

    Full Text Available In a world of globalization generating geographical concentration, relocation of activities, thus inducing territorial disparities, territorial cohesion has become a prerequisite for achieving sustainable economic growth and implementing social and economic cohesion. The ratification of Lisbon Treaty represents the moment when “Territorial Cohesion” has been added as an official policy aim of the EU to its previous aims of economic and social cohesion. Thus, the process of defining this concept of “Territorial Cohesion” has become the task of the Commission and EU Member States. Based on a literature review, the paper describes, in the first section, the polysemantic nature of territorial cohesion. The main objective of the next section is to address the main indicators, directly related to territorial objectives, that could be used to support policy makers in measuring and monitoring territorial cohesion related to European territorial development.

  17. Cohesive strength of iron ore granules

    Directory of Open Access Journals (Sweden)

    Contreras Rafael Jaimes

    2017-01-01

    Full Text Available We present an experimental and numerical investigation of the mechanical strength of crude iron ore (Hematite granules in which capillary bonds between primary particles are the source of internal cohesion. The strength is measured by subjecting the granules to vertical compression between two plates. We show that the behavior of the granules is ductile with a well-defined plastic threshold which increases with the amount of water. It is found that the compressive strength scales with capillary cohesion with a pre-factor that is nearly independent of size polydispersity for the investigated range of parameters but increases with friction coefficient between primary particles. This weak dependence may be attributed to the class of fine particles which, due to their large number, behaves as a cohesive matrix that controls the strength of the granule.

  18. Cohesive strength of iron ore granules

    Science.gov (United States)

    Contreras, Rafael Jaimes; Berger, Nicolas; Izard, Edouard; Douce, Jean-François; Koltsov, Alexey; Delenne, Jean-Yves; Azema, Emilien; Nezamabadi, Saeid; van Loo, Frédéric; Pellenq, Roland; Radjai, Farhang

    2017-06-01

    We present an experimental and numerical investigation of the mechanical strength of crude iron ore (Hematite) granules in which capillary bonds between primary particles are the source of internal cohesion. The strength is measured by subjecting the granules to vertical compression between two plates. We show that the behavior of the granules is ductile with a well-defined plastic threshold which increases with the amount of water. It is found that the compressive strength scales with capillary cohesion with a pre-factor that is nearly independent of size polydispersity for the investigated range of parameters but increases with friction coefficient between primary particles. This weak dependence may be attributed to the class of fine particles which, due to their large number, behaves as a cohesive matrix that controls the strength of the granule.

  19. Discrete Modelling of Powder Dispersion in Dry Powder Inhalers - A Brief Review.

    Science.gov (United States)

    Tong, Zhenbo; Yu, Aibing; Chan, Hak-Kim; Yang, Runyu

    2015-01-01

    The performance of a dry powder inhaler (DPI) depends on powder properties as well as the air and particle flows in the device. The main principle of powder dispersion is to overcome the inter-particle cohesion using various dispersion/ de-agglomeration forces. While different dispersion mechanisms have been identified, their relative importance under different conditions is less clear. The lack of understanding of these mechanisms is a major obstacle to the advance of pharmaceutical powder aerosol technology. This paper briefly reviews our recent effort in developing a combined computational fluid dynamics (CFD) and discrete element method (DEM) approach to gain such pivotal information. Dispersions under various specifically designed conditions were simulated to exam the role of individual dispersion mechanism. The air and particle flows were analysed at the particle scale and linked to dispersion performance characterised by fine particle fraction (FPF). In addition, the dispersion mechanisms of both drug only and carrier based formulations in a commercial inhaler were studied. Our work shows that the approach has the potential to develop a theoretical framework for designing new DPIs.

  20. Rotation Induced Disruption of Cohesive Asteroids

    Science.gov (United States)

    Sanchez Lana, Diego; Scheeres, D. J.

    2013-10-01

    We use a Soft-Sphere Discrete Element Method (SSDEM) code to study the evolution of self-gravitating cohesive granular aggregates that are spun to disruption as a proxy to "rubble-pile" asteroids. Calculations have shown that the fine regolith in asteroids and molecular Van der Waals forces together may act as a cohesive matrix that provides enough structural strength to hold small NEAs together even at the observed high spin rates. With this in mind we have implemented cohesive forces between the large 10 m) particles that form our aggregates; its strength being controlled by the mean particle size of the matrix. The addition of rolling friction also has allowed us to obtain cohesionless aggregates with friction angles of at least 35° as measured by the Drucker-Prager yield criterion. A series of experiments were run with the code, keeping the size, density and number of grains constant while increasing the cohesive strength of the matrix holding the grains in place. It can be shown, through a scaling analysis, that when the cohesive strength between rubble pile components is increased by a factor of f, that the effective size of the asteroid being modeled will decrease by a factor of 1/√f. To evaluate this we ran a series of 12 cases with increasing cohesive strength, effectively modeling rubble piles of size from 0.1 km up to 100 km with a constant cohesive strength of 25 Pa. Some of our main results are as follows: 1. results from simulations are compatible with a simple model of asteroid strength that predicts, in the cohesion dominated case, that the spin rate for fission is inversely proportional to the size of the asteroid; 2. aggregates may disrupt by shedding or fission, depending on the cohesive strength and the size of the aggregate (shape and heterogeneity factors have not yet been considered); 3. disruption by fission is more likely for small aggregates than for larger aggregates with the same cohesive strength. Further results with spherical and a

  1. Comparison of the Kinetic Behaviors of Fe{sub 2}O{sub 3} Spherical Submicron Clusters and Fe{sub 2}O{sub 3} Fine Powder Catalysts for CO Oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Seunggyun; Kim, Jinhoon; Lee, Sunghan [Yonsei Univ., Wonju (Korea, Republic of); Kim, Unho; Jung, Jinseung [Gangneung-Wonju National Univ., Gangneung (Korea, Republic of)

    2014-05-15

    α-Fe{sub 2}O{sub 3} spherical particles having an average diameter of ca. 420 nm and α-Fe{sub 2}O{sub 3} fine particles (< 10 μm particle size) were prepared to examine as catalysts for CO oxidation. Kinetic studies on the catalytic reactions were performed in a flow reactor using an on-line gas chromatography system operated at 1 atm. The apparent activation energies and the partial orders with respect to CO and O{sub 2} were determined from the rates of CO disappearance in the reaction stage showing a constant catalytic activity. In the temperature range of 150-275 .deg. C, the apparent activation energies were calculated to be 13.7 kcal/mol on the α-Fe{sub 2}O{sub 3} spherical submicron clusters and 15.0 kcal/mol on the α-Fe{sub 2}O{sub 3} fine powder. The Pco and PO{sub 2} dependencies of rate were investigated at various partial pressures of CO and O{sub 2} at 250 .deg. C. Zero-order kinetics were observed for O{sub 2} on both the catalysts, but the reaction order for CO was observed as first-order on the α-Fe{sub 2}O{sub 3} fine powder and 0.75-order on the α-Fe{sub 2}O{sub 3} spherical submicron clusters. The catalytic processes including the inhibition process by CO{sub 2} on the α-Fe{sub 2}O{sub 3} spherical submicron powder are discussed according to the kinetic results. The catalysts were characterized using XRD (X-ray powder diffraction), FE-SEM (field emission-scanning electron microscopy), HR-TEM (high resolution-transmission electron microscopy), and N{sub 2} sorption measurements.

  2. Sustainability of National Cohesion

    Directory of Open Access Journals (Sweden)

    Andrei Mihai Cristea

    2013-09-01

    Full Text Available In the European Union, cohesion policy is the third country after the domestic and social policy, as this policy is a tool for economic growth and also a balancing factor. Through its solidarity funds contribute to the other sectorial policies: the Common Agricultural Policy, social policy, environmental policy. This article aims to demonstrate the importance of cohesion policy in the national economy and how to improve its implementation by ensuring sustainable development and sustainable economic growth

  3. 我国超细铜粉研究及生产现状%Status-in-art of Preparation and Production of Ultra-fine Copper Powder in China

    Institute of Scientific and Technical Information of China (English)

    黄凌云; 朱国才; 霍慧彬; 池汝安

    2008-01-01

      The status-in-art of preparation and production of ultra-fine copper powder including ball mill, plasma,γ-ray irradiation-hydrothermal crystallization, chemical reduction, electrolysis, ultrasound electrolysis, hydrothermal, micro emulsions and collosol method are summarized. The advance of pre-reduction-complex reduction used by Institute of Nuclear and New Energy Technology, Tsinghua University was introduced, too. Furthermore, the present state of copper powder consumption and production in China were also analyzed. Finally, the development of ultra-fine copper powder is prospected.%  概述了目前超细铜粉制备方法,包括球磨法、等离子体法、γ射线辐照射法、雾化法、超声电解法、电解法、微乳液法、溶胶-凝胶法、化学还原法等的研究现状,介绍了清华大学核能与新能源技术研究院采用的预还原-复合还原法。同时,对我国的铜粉消费与生产现状作了分析,并对我国今后超细铜粉研究作了展望。

  4. 阻旋料位开关在细粉分离器料仓中的应用%The application of a level control by rotary paddle in the fine powder separator bunker

    Institute of Scientific and Technical Information of China (English)

    黄毅; 朱建国; 李诗媛; 吕清刚; 包绍麟

    2012-01-01

    描述了阻旋料位开关的工作原理及在细粉分离器料仓中的应用,测试表明,在粉尘浓度大、颗粒粒度细的料仓内,阻旋料位开关可准确监测料仓料位,为料位的控制提供了可靠保障,提高了细粉分离器的分离效率,减少了物料逃逸量,有利于杭州七格100 t/d污泥焚烧工程的连续运行.%A level control by rotary paddle is applied in the fine powder separator bunker to monitor material position. Its principle is also described in this paper. The operation results prove that the material position with high dust concentration and fine particles in the bunker can be rightly monitored by this level control. As a result, the instrument of rotary paddle provides reliable technology for the level control, which is profitable to increase the separation efficiency and lessen the particle escape rate. The application of such kind of level control in the fine powder separator bunker is effective to keep the continuous operation of the sewage sludge incineration project in Qige of Hangzhou.

  5. Kinetic energy density and agglomerate abrasion rate during blending of agglomerates into powders

    NARCIS (Netherlands)

    Willemsz, Tofan A; Hooijmaijers, Ricardo; Rubingh, Carina M; Tran, Thanh N; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

    2012-01-01

    Problems related to the blending of a cohesive powder with a free flowing bulk powder are frequently encountered in the pharmaceutical industry. The cohesive powder often forms lumps or agglomerates which are not dispersed during the mixing process and are therefore detrimental to blend uniformity.

  6. 大掺量矿物细粉掺和料活性粉末混凝土高温性能%High Temperature Performance of High Volume Fine Mineral Mixture of Reactive Powder Concrete

    Institute of Scientific and Technical Information of China (English)

    刘娟红; 宋少民

    2012-01-01

    This paper researches the burst properties of high temperature and compressive strength after heating of high volume fine mineral mixture of reactive powder concrete. Results show that with the decrease of the water-cement ratio, the burst temperature of the specimen decreases and the burst probability increases. The initial time and temperature of high-temperature burst decrease with increasing amount of fine mineral mixture. Polypropylene fiber can effectively improve the anti-burst performance of reactive powder concrete. Reactive powder concrete after 200 ℃ heating can increase the compressive strength. In addition, adding polypropylene fiber can improve the compressive strength of reactive powder concrete and residual strength ratio in the range of 200 ℃.%研究了大掺量矿物细粉活性粉末混凝土高温爆裂性能和高温后的抗压强度.结果表明,试件的爆裂温度随着水胶比的减小而降低,爆裂几率随水胶比的降低而增大;高温爆裂的初始时间和温度随矿物细粉掺和料掺量增多而降低;聚丙烯纤维能有效地改善活性粉末混凝土抗爆裂性能;活性粉末混凝土经200屯高温后的抗压强度有所增加,且聚丙烯纤维的加入可使活性粉末混凝土抗压强度和200℃范围内残余强度率有一定幅度提高.

  7. The influence of amino acids on aztreonam spray-dried powders for inhalation

    Directory of Open Access Journals (Sweden)

    Xiao-Fei Yang

    2015-12-01

    Full Text Available The dry powder inhalation of antibiotics for the treatment of lung infections has attracted drastically increasing attention as it offers rapid local therapy at lower doses and minimal side effects. In this study, aztreonam (AZT was used as the model antibiotic and spray-dried to prepare powders for inhalation. Amino acids of glycine (GLY, histidine (HIS and leucine (LEU were used as excipients to modify the spray-dried particles. It was demonstrated that the GLY-AZT spray-dried powders formed huge agglomerates with the size of 144.51 µm, which made it very difficult to be delivered to the lungs (FPF: 0.29% w/w only. In comparison with the AZT spray-dried powders, HIS-modified spray-dried powders showed increased compressibility, indicating larger distance and less cohesion between particles; while the LEU-modified spray-dried particles showed a hollow structure with significantly decreased densities. The fine particle fraction for HIS- and LEU-modified powders was 51.4% w/w and 61.7% w/w, respectively, and both were significantly increased (one-way ANOVA, Duncan's test, P < 0.05 compared to that of AZT spray-dried powders (45.4% w/w, showing a great potential to be applied in clinic.

  8. Extremely fine structured cathode for solid oxide fuel cells using Sr-doped LaMnO3 and Y2O3-stabilized ZrO2 nano-composite powder synthesized by spray pyrolysis

    Science.gov (United States)

    Shimada, Hiroyuki; Yamaguchi, Toshiaki; Sumi, Hirofumi; Nomura, Katsuhiro; Yamaguchi, Yuki; Fujishiro, Yoshinobu

    2017-02-01

    A solid oxide fuel cell (SOFC) for high power density operation was developed with a microstructure-controlled cathode using a nano-composite powder of Sr-doped LaMnO3 (LSM) and Y2O3-stabilized ZrO2 (YSZ) synthesized by spray pyrolysis. The individual LSM-YSZ nano-composite particles, formed by crystalline and amorphous nano-size LSM and YSZ particles, showed spherical morphology with uniform particle size. The use of this powder for cathode material led to an extremely fine microstructure, in which all the LSM and YSZ grains (approximately 100-200 nm) were highly dispersed and formed their own network structures. This microstructure was due to the two phase electrode structure control using the powder, namely, nano-order level in each particle and micro-order level between particles. An anode-supported SOFC with the LSM-YSZ cathode using humidified H2 as fuel and ambient air as oxidant exhibited high power densities, such as 1.29 W cm-2 under a voltage of 0.75 V and a maximum power density of 2.65 W cm-2 at 800 °C. Also, the SOFC could be stably operated for 250 h with no degradation, even at a high temperature of 800 °C.

  9. Types of gas fluidization of cohesive granular materials.

    Science.gov (United States)

    Valverde, Jose Manuel; Castellanos, Antonio

    2007-03-01

    Some years ago it was shown that gas-fluidized powders may transit from solid-like to fluid-like fluidization prior to bubbling, shedding light on a long-standing controversy on the nature of "homogeneous" fluidization. In this paper it is shown that some gas-fluidized powders may also transit from the fluid-like regime to elutriation, with full suppression of the bubbling regime. We provide a diagram that can be used to predict these types of fluidization exhibited by cohesive powders based on simple phenomenological equations in which particle aggregation due to attractive forces is a key ingredient.

  10. 21 CFR 73.1646 - Bronze powder.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Bronze powder. 73.1646 Section 73.1646 Food and... ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1646 Bronze powder. (a) Identity. (1) The color additive bronze powder is a very fine metallic powder prepared from alloys consisting principally of...

  11. 超细干粉灭火系统应用于加油站火灾防控初探%Pre-test of Fire Prevention and Control of Gas Station Using Super Fine Powder Fire Extinguishing System

    Institute of Scientific and Technical Information of China (English)

    谢树俊; 宋文华; 丁旭东; 徐昕; 张俪昽

    2011-01-01

    Aiming at the fast spread speed and the strong fire behavior of gas station fire, the traditional mobile, cart-type dry powder and foam extinguishers can not meet the requirements of gas station fire safety situation. Based on "Code of design,Construction and Acceptance for Super fine powder extinguish system ","super fine powder fire extinguishing system design, construction and acceptance specification" and other related standards, combined with the gas station engineering design requirements and the characteristics of fire hazards, the design principles of gas station by using super fine powder fire extinguishing system for fire fighting and initial control was given. Take a gas station in Tianjin as an example, using the given design principles to the fire control system of its key fire danger area's design, the equipment selection and system capability evaluation were given. Under the given condition, compared with the gas station fire equipment based on the standards, design selection of super fine powder fire extinguishing facilities is equipped with simple, flexible and convenient advantages, and also remarkable extinguishing effect. It can also maximize the attack speed and minimizing the risk of fighting and casualties, the gas station's capability of prevention and control of sudden fire has been significantly upgraded.%针对加油站火灾起火速度快、火势猛,传统的手提、推车式干粉及泡沫灭火器不能满足加油站消防安全要求的实际情况,依据《汽车加油加气站设计与施工规范》、《超细干粉灭火系统设计、施工及验收规范》等相关标准,结合加油站工程设计的要求和火灾隐患的特点,给出加油站采用超细干粉灭火系统用于火灾扑救与初期控制时,设计应遵循的原则.以天津某加油站为例,利用给出的设计原则对其重点火灾隐患部位的消防系统进行了设计、设备选型与系统消防能力评估,在给定的条件下,选用超

  12. Adhesion and cohesion.

    Science.gov (United States)

    von Fraunhofer, J Anthony

    2012-01-01

    The phenomena of adhesion and cohesion are reviewed and discussed with particular reference to dentistry. This review considers the forces involved in cohesion and adhesion together with the mechanisms of adhesion and the underlying molecular processes involved in bonding of dissimilar materials. The forces involved in surface tension, surface wetting, chemical adhesion, dispersive adhesion, diffusive adhesion, and mechanical adhesion are reviewed in detail and examples relevant to adhesive dentistry and bonding are given. Substrate surface chemistry and its influence on adhesion, together with the properties of adhesive materials, are evaluated. The underlying mechanisms involved in adhesion failure are covered. The relevance of the adhesion zone and its importance with regard to adhesive dentistry and bonding to enamel and dentin is discussed.

  13. Adhesion and Cohesion

    Directory of Open Access Journals (Sweden)

    J. Anthony von Fraunhofer

    2012-01-01

    Full Text Available The phenomena of adhesion and cohesion are reviewed and discussed with particular reference to dentistry. This review considers the forces involved in cohesion and adhesion together with the mechanisms of adhesion and the underlying molecular processes involved in bonding of dissimilar materials. The forces involved in surface tension, surface wetting, chemical adhesion, dispersive adhesion, diffusive adhesion, and mechanical adhesion are reviewed in detail and examples relevant to adhesive dentistry and bonding are given. Substrate surface chemistry and its influence on adhesion, together with the properties of adhesive materials, are evaluated. The underlying mechanisms involved in adhesion failure are covered. The relevance of the adhesion zone and its importance with regard to adhesive dentistry and bonding to enamel and dentin is discussed.

  14. New Strategies for Powder Compaction in Powder-based Rapid Prototyping Techniques

    NARCIS (Netherlands)

    Budding, A.; Vaneker, Thomas H.J.

    2013-01-01

    In powder-based rapid prototyping techniques, powder compaction is used to create thin layers of fine powder that are locally bonded. By stacking these layers of locally bonded material, an object is made. The compaction of thin layers of powder mater ials is of interest for a wide range of

  15. Competition and social cohesion

    Directory of Open Access Journals (Sweden)

    Mario Libertini

    2014-03-01

    Full Text Available "Competition" and "social cohesion" are both protected by E.U. and Italian laws. The author moves from the analysis of the meaning of these two concepts, in order to reflect on their compatibility and the way to conciliate them. The central problem - in the opinion of the Author - is to abandon the myth of spontaneous markets' order and to rebuild a political order able to maintain and support, as far as possible, the competitive market economy, but also to govern economic processes in critical moments and situations.

  16. Review of Cohesion in Indexing

    Directory of Open Access Journals (Sweden)

    Hasan Ashrafi Rizi

    2007-07-01

    Full Text Available Indexers often disagree on judging terms that best reflect the content of a document. Difference of opinion highlights one of the characteristics of indexing which is indexing cohesion. Also known as consistency, little study of the subject matter has been undertaken in the past few years. However, its importance has been recently acknowledged in effective information retrieval and expansion of access points to the document content. The present paper investigates cohesion in indexing. In addition of presenting the definitions offered by experts, it takes note of the factors influencing indexing cohesion. Methods for measuring cohesion are offered.

  17. Synthesis of Uranium nitride powders using metal uranium powders

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Jae Ho; Kim, Dong Joo; Oh, Jang Soo; Rhee, Young Woo; Kim, Jong Hun; Kim, Keon Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2012-10-15

    Uranium nitride (UN) is a potential fuel material for advanced nuclear reactors because of their high fuel density, high thermal conductivity, high melting temperature, and considerable breeding capability in LWRs. Uranium nitride powders can be fabricated by a carbothermic reduction of the oxide powders, or the nitriding of metal uranium. The carbothermic reduction has an advantage in the production of fine powders. However it has many drawbacks such as an inevitable engagement of impurities, process burden, and difficulties in reusing of expensive N{sup 15} gas. Manufacturing concerns issued in the carbothermic reduction process can be solved by changing the starting materials from oxide powder to metals. However, in nitriding process of metal, it is difficult to obtain fine nitride powders because metal uranium is usually fabricated in the form of bulk ingots. In this study, a simple reaction method was tested to fabricate uranium nitride powders directly from uranium metal powders. We fabricated uranium metal spherical powder and flake using a centrifugal atomization method. The nitride powders were obtained by thermal treating those metal particles under nitrogen containing gas. We investigated the phase and morphology evolutions of powders during the nitriding process. A phase analysis of nitride powders was also a part of the present work.

  18. Document Cohesion Flow: Striving towards Coherence

    NARCIS (Netherlands)

    Crossley, Scott; Dascalu, Mihai; Trausan-Matu, Stefan; Allen, Laura; McNamara, Danielle

    2016-01-01

    Text cohesion is an important element of discourse processing. This paper presents a new approach to modeling, quantifying, and visualizing text cohesion using automated cohesion flow indices that capture semantic links among paragraphs. Cohesion flow is calculated by applying Cohesion Network

  19. Document Cohesion Flow: Striving towards Coherence

    NARCIS (Netherlands)

    Crossley, Scott; Dascalu, Mihai; Trausan-Matu, Stefan; Allen, Laura; McNamara, Danielle

    2016-01-01

    Text cohesion is an important element of discourse processing. This paper presents a new approach to modeling, quantifying, and visualizing text cohesion using automated cohesion flow indices that capture semantic links among paragraphs. Cohesion flow is calculated by applying Cohesion Network Analy

  20. The effect of hyaluronic acid on brushite cement cohesion.

    Science.gov (United States)

    Alkhraisat, M H; Rueda, C; Mariño, F T; Torres, J; Jerez, L B; Gbureck, U; Cabarcos, E L

    2009-10-01

    The improvement of calcium phosphate cement (CPC) cohesion is essential for its application in highly blood perfused regions. This study reports the effectiveness of hyaluronic acids of different molecular weights in the enhancement of brushite cement cohesion. The cement was prepared using a powder phase composed of a mixture of beta-tricalcium phosphate and monocalcium phosphate monohydrate, whereas the liquid phase was formed by 0.5M citric acid solution modified by the addition of hyaluronic acid of different molecular weights. It was found that medium and high molecular weight hyaluronic acid enhances the cement cohesion and scarcely affects the cement mechanical properties. However, concentrations >0.5% (w/v) were less efficient to prevent the cement disintegration. It is concluded that hyaluronic acid could be applied efficiently to reduce brushite cement disintegration.

  1. Leadership, cohesion and groupthink

    Directory of Open Access Journals (Sweden)

    Iurchevici Iulia

    2016-09-01

    Full Text Available The Groupthink Phenomenon refers to the tendency of the members of a group to reach solidarity and cohesion, the trend that makes to bypass any questions which would lead to disputes. In such cases, if the members expect counter-arguments regarding a certain issue, they avoid to raise the matter. If it is believed that a question cannot be answered – it isn’t asked. Originally, Janis the author of the term, explains this process through the environment that has been established within groups that are in the leading position, but later, puts a strong emphasis towards the tendency to maintain the unanimity of the decision of the group. As preceding conditions of this decision-making process are listed the following: the high cohesion of the group, its isolation from other external sources of information, the lack of an impartial leadership, lack of appropriate legal framework and procedures in the decision - making process, and also “homogeneity of members, background and their ideology”. The Groupthink is manifested by: Illusion of Invulnerability, Collective Rationalization, Illusion of morality, Out – Group Stereotypes, Strong pressures towards conformism, Self – Censorship, Illusions of unanimity, and the presence of “Mind Guards”. In order to understand the decisions of a group, it is important that some analysis of Groupthink to be done, because in this way, can be controlled or eliminated the communicational distortion that occurs at a time among members forming these groups.

  2. CHINESE RE POLISHING POWDER INDUSTRY

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Due to its high polishing efficiency, long working life and wide application range, RE polishing powder has become the most popular fine polishing material. In recent years, accompanying the rapid development of electronic information technology, the demand for polishing powder is

  3. Experimental study on ultra-fine powder purification of pulse-jet cartridge dust collector%脉冲滤筒除尘器对超细粉体净化的实验研究

    Institute of Scientific and Technical Information of China (English)

    林莉君; 周露

    2012-01-01

    随着工业的快速发展,空气中颗粒污染物的含量和种类越来越多,不仅对人体健康造成危害,颗粒污染还对能见度、气候、动植物均有影响,寻找合适的除尘设备,提高对微细粉尘的除尘效率,对安全和环境保护有着重要而深远的意义.该文利用脉冲滤筒除尘器对粒径分布为0.5-5μm的超细粉体进行净化实验.测试了除尘器净化效率、除尘器阻力及过滤风速等主要性能参数.实验结果说明:脉冲滤筒除尘器对于粒径为0.5-5μm超细粉体,在过滤风速为0.8-1.25m/min时,除尘器阻力小于300Pa,净化效率达99.9999%.得到结论:滤筒除尘器具有高除尘效率,低阻力损失,节约除尘系统的动力消耗的优点,有利于在超细粉体净化工艺中的应用.%With fast development of the Industry, more and more content and species of paniculate pollutants are in the air. The partieulate pollutants not only cause harm to the human health, but also have negative effect on the visibility , the climate , animals and plants. So it is important to safety and environmental protection that finding suitable dust collecting equipments and raising dust removal efficiency of fine dust particles.This paper was on the use of the pulse-jet cartridge dust collector to do the purifying experiment of the ultra-fine powder. The experimental tested the main characters of the pulse-jet cartridge dust collector, such as the purifying efficiency, the dust resistance and the filtering speed. The experimental results were that this study was used by the pulse-jet cartridge dust collector to purify 0.5μm - μm ultra-fine powders, tested the filtering speed were 0. 8 m/min-1.25m/min, dust resistance was less than 300Pa and the purifying efficiency was 99.9999% . At last, it comes to a conclusion; the pulse-jet cartridge filters are with the advantages of high efficiency, low pressure drop and save power to the dust removal system. The pulse-jet cartridge f dust

  4. 机械活化对矿浆电解制备细铜粉的影响%EFFECTS OF MECHANICAL ACTIVATION ON FINE COPPER POWDER PREPARED BY SLURRY ELECTROLYSIS

    Institute of Scientific and Technical Information of China (English)

    刘维平

    2012-01-01

    Mechanical activation pretreatment of copper concentrate was carried out in high energy ball mill, fine copper powder was made from activated copper concentrate by means of slurry electrolysis. The structure changes of copper concentrate with activation time and ball mill intensity were studied by means of XRD analysis. The size and shape changes of activated and deactivated copper powders were studied. The results show that the specific surface area of copper concentrate increases after mechanical activation, and crystal structure tends to amorphous. After standing for long time, the activity of copper concentrate disappears. Copper powder made from deactivated copper concentrate is easy to agglomerate and coarsen, and its shape is of arborization. The size of copper powder made from activated copper concentrate is less than 10μm, its size distribution is narrow, and its shape is granular and regular.%采用高能机械球磨对铜精矿进行机械活化预处理,以活化的铜精矿为原料,采用矿浆电解法制备细铜粉.通过XRD分析,研究了铜精矿结构随活化时间及球磨强度的变化;通过激光粒度分析及SEM分析,研究了机械活化失效前后铜粉粒度及形貌的变化.结果表明:铜精矿经机械活化后,比表面积增加,晶体结构趋于无定形化;活化后的铜精矿经长时间静置,活性消失;利用失活的铜精矿制备得到的铜粉易团聚,粒度变粗,形貌呈树枝状,而利用活化的铜精矿制备得到的铜粉粒度均小于10 μm,粒度分布窄,形状规则,外观呈粒状.

  5. Social Cohesion and Voluntary Associations

    Science.gov (United States)

    Heuser, Brian L.

    2005-01-01

    Voluntary organizations exert great influence over how social norms and ethical codes are guided into action. As such, they have a significant impact on societal levels of social cohesion. Although social capital involves generalized trust becoming manifest as spontaneous sociability, social cohesion is determined by how that sociability is…

  6. Thermodynamic Analysis and Synthesis of Fine WC Powder in the WO3-CH4-H2 System Using Excessive CH4

    Science.gov (United States)

    Cetinkaya, S.; Eroglu, S.

    2017-10-01

    This study aims to investigate reaction behavior of WO3 powder in H2-CH4 flow using excessive CH4 with respect to the oxide at 900-1300 K for 60 min and 120 min. Mass measurement, x-ray diffraction and scanning electron microscopy techniques were used to characterize the products. The oxide reduction occurred prior to the carburization possibly owing to high H2 diffusivity. WC formation significantly increased with temperature, but slightly with time. Incomplete carburization was observed at 900-1100 K, whereas single WC phase was attained at 1200 K and 1300 K for both reaction times. The thermodynamics predicted single WC phase at 900-980 K, and free C phase along with WC at 980-1300 K. The results have been discussed in terms of solid state C diffusivity, CH4 decomposition, CH4 residence time, defects and self-created local atmosphere. The mean particle size increased with temperature from 0.15 µm at 900 K to 1 µm at 1300 K.

  7. Fabricating fine-grained tungsten heavy alloy by spark plasma sintering of low-energy ball-milled W–2Mo–7Ni–3Fe powders

    Energy Technology Data Exchange (ETDEWEB)

    Xiang, D.P., E-mail: dpxiang@hainu.edu.cn [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China); School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Ding, L. [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China); Li, Y.Y. [School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou 510640 (China); Chen, X.Y.; Zhang, T.M. [Key Laboratory of Advanced Materials of Tropical Island Resources, Ministry of Education, Hainan University, Haikou 570228 (China)

    2013-08-20

    Fine-grained W–2Mo–7Ni–3Fe heavy alloys were fabricated by low-energy ball milling (LEBM)-assisted spark plasma sintering at a temperature range of 1000–1250 °C. The effects of sintering temperature on the phase evolution, microstructural characteristics, and mechanical properties of the alloys were studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), hardness testing, and universal testing. The XRD results show that small intermetallic compounds, such as NiW and Ni{sub 2}W{sub 4}C, form in the alloys. The W–2Mo–7Ni–3Fe alloys are characterized by white W grains, a gray W-rich microstructure that contains Mo, and a black γ–(Ni, Fe, W, Mo) binding phase. The X-ray energy dispersive analysis (EDS) shows that the Mo, Ni, and Fe that form a solid solution with W in the gray structure gradually decrease with increasing temperature. The hardness and bending strength of the alloys initially increase and then decrease with rising sintering temperature. Moreover, the alloys sintered at different temperatures exhibit dissimilar bending fracture modes.

  8. PREPARATION OF ULTRA-FINE SUPERCONDUCTING YBa2Cu3O7-x POWDERS BY GEL COMBUSTION PROCESS%凝胶燃烧法制备超细YBa2Cu3O7-x超导粉末

    Institute of Scientific and Technical Information of China (English)

    郭建栋; 徐晓林; 王永忠; 张炎; 刘达颐; 石磊

    2005-01-01

    The ultra-fine superconducting YBa2Cu3O7-x powders were prepared by means of the gel combustion process using nitrates of Y, Ba and Cu as the starting materials and citric acid as the fuel. The resulting particle size and its superconducting properties is dependent on the nature of the auto-ignition reaction, which in turn depends upon the citrate-nitrate ratio in the gel. An attempt to determine the optimal citrate-nitrate ratio has been made in order to obtain pure, homogeneous and reasonably fine YBCO superconductor. In our experiments we found the best fuel-oxidant molar ratio to be 0.5.%纳米级细度的YBa2Cu3O7-x超导粉末有可能在第二代超导带材的研制中得到应用.超细YBa2Cu3O7-x超导粉末已经通过凝胶燃烧法制备成功.使用的起始物质是钇、钡、铜的硝酸盐以及作为燃烧剂的柠檬酸.产物颗粒的尺寸大小及其超导性能依赖于自燃过程的情况,而自燃过程又与凝胶中柠檬酸盐-硝酸盐的YBa2Cu3O7-x超导粉末.在本实验中我们发现最好的燃烧剂-氧化剂摩尔比为0.5.

  9. Compaction of Titanium Powders

    Energy Technology Data Exchange (ETDEWEB)

    Gerdemann, Stephen,J; Jablonski, Paul, J

    2011-05-01

    Accurate modeling of powder densification has been an area of active research for more than 60 years. The earliest efforts were focused on linearization of the data because computers were not readily available to assist with curve-fitting methods. In this work, eight different titanium powders (three different sizes of sponge fines<150 {micro}m,<75 {micro}m, and<45 {micro}m; two different sizes of a hydride-dehydride [HDH]<75 {micro}m and<45 {micro}m; an atomized powder; a commercially pure [CP] Ti powder from International Titanium Powder [ITP]; and a Ti 6 4 alloy powder) were cold pressed in a single-acting die instrumented to collect stress and deformation data during compaction. From these data, the density of each compact was calculated and then plotted as a function of pressure. The results show that densification of all the powders, regardless of particle size, shape, or chemistry, can be modeled accurately as the sum of an initial density plus the sum of a rearrangement term and a work-hardening term. These last two terms are found to be a function of applied pressure and take the form of an exponential rise.

  10. 片状超细WS2粉末的制备及其润滑性能研究%Preparation and Tribological Properties of Sheet-like Fine WS2 Powder

    Institute of Scientific and Technical Information of China (English)

    唐宜; 欧耀辉; 喻姣; 陈鹏; 凌晨

    2011-01-01

    When the base planes of WS2 particles are parallel to the surface of metal, the tribological performance will be the best. Therefore,2D sheet-like nanostructures can greatly improve its tribological properties. To obtain such microstructures, a mixture of analytically pure WO3 and S powder was energetically ball-milled in Ar atmosphere, the ball-milled mixture was sulfurized in sulfur vapor. XRD phase detection and SEM morphology observation shows that sheet-like and fine WS2 powder with edge length between 250 ~ 500 nm and thickness less than 100 nm is obtained through the route of ballmilling to sulfuration. The obtained product was added into liquid paraffin to investigate its tribological behavior using standard four-ball test method. The result shows that the powder can increase the maximum non-seizure load of liquid paraffin and decrease the average wear scar diameter of the below balls obviously. The maximum non-seizure load value increases 118 N when adding 1.3% WS2 powder and the average wear diameter decreases 0. 33 mm when adding 1.5% WS2 powder.%当WS2粉末的基面与材料表面平行时,润滑效果最好,因此纳米片状形貌能极大地改善WS2粉末的润滑效果.为制备纳米片状WS2粉末,将分析纯WO3和S粉末在氩气保护下进行球磨,将球磨后的混合粉末在硫蒸气气氛中进行硫化得到WS2粉末.基于XRD和SEM的成分和形貌分析表明,通过球磨加硫化的方法成功制备出边缘长度在250~500 nm,厚度小于100 nm的片状超细WS2粉末.将片状超细WS2粉末添加到石蜡油中进行标准四球摩擦试验,结果表明:该粉末可显著提高石蜡油最大无卡咬负荷值,同时有效减小磨斑直径,其中质量分数1.3%的片状超细WS2粉末可使石蜡油的最大无卡咬负荷值增加118 N,质量分数1.5%的片状超细WS2粉末可使试样的平均磨斑直径减小0.33mm.

  11. Preparation of ultra-fine silver powder for solar cell grid electrode%太阳能电池正极浆料用超细银粉的制备

    Institute of Scientific and Technical Information of China (English)

    李纪; 黄惠; 郭忠诚

    2013-01-01

    Using ascorbic acid as reducing agent and poly (ethylene glycol) 4000 as dispersant, the ultra-fine sil-ver powder for solar cell grid electrode was prepared by chemical reduction. The morphology, size and purity of silver powder were analyzed by scanning electron microscopy (SEM) laser particle analyzer and X-ray diffraction (XRD). The influences of reducing concentration of poly (ethylene glycol) 4000, silver nitrate, ascorbic acid, and pH value on the particle size and morphology were researched. The results show that the particle size of the silver powders decreases to be more stable with increasing dispersant concentration. The optimal reductive con-dition is: the pH value equals to 4, the concentration of ascorbic acid and silver nitrate is 2. 0 and 0. 5mol/L and m ( PEG4000)/m (AgNO3) is 0. 10. Spherical silver powder with 5. 32μm of particle size is good dispersion, high purity, face-centered cubic lattice. The paste prepared with ready-made silver powder was printed on the silicon,and the square resistance of the sintered film tested by four-point probe is 4. 27mΩ/□ indicating the electrical property of the prepared silver is qualified for solar cell.%采用液相化学还原法,以聚乙二醇4000为分散剂,用抗坏血酸直接还原硝酸银溶液制备太阳能电池正极浆料用银粉.通过扫描电镜(SEM)、激光粒度分析仪和X射线衍射仪(XRD)等方法分析银粉的形貌、粒度及纯度,研究分散剂用量、抗坏血酸浓度、硝酸银浓度和溶液pH值等工艺条件对银粉粒度、物相结构及形貌的影响.结果表明,随着分散剂用量的增大,银粉颗粒粒度先减小后趋于稳定.在溶液pH值为4,抗坏血酸浓度和硝酸银浓度分别为2.0和0.5mol/L,聚乙二醇4000与硝酸银的质量比为0.10时,可以制得分散性好、纯度高、面心立方晶系和平均粒度为5.32μm的规则球形银粉.并将所得银粉调制成太阳能电池用浆料,通过丝网印刷在硅片上,使用

  12. Immigration, social cohesion, and naturalization

    DEFF Research Database (Denmark)

    Lægaard, Sune

    2010-01-01

    social trust do not connect with issues of naturalization at all. Other conceptions of social cohesion are either politically controversial, problematic as part of the justification of stricter naturalization requirements, or in fact justify less demanding naturalization requirements.......The standard appeal to social cohesion in relation to immigration concerns admittance and residence. But social cohesion is sometimes also invoked as a relevant concern in relation to the attainment of citizenship in the state through naturalization. Many western states have recently tightened...... conditions for naturalization and introduced tougher language requirements and knowledge of society tests. The article discusses how concerns for social cohesion might function as a part of justifications of such restrictive naturalization requirements. It argues that standard concerns with generalized...

  13. Key Techniques for the Construction of the 3rd System Fine-Powdered Sandy Rock Section of the Humaling Tunnel%胡麻岭隧道第三系粉细砂岩段施工关键技术

    Institute of Scientific and Technical Information of China (English)

    徐长久

    2011-01-01

    胡麻岭隧道3#、4#斜井和隧道正洞区段穿越第三系弱胶结粉细砂岩,由于地层岩性软,地下水丰富,施工中涌水、流砂、掌子面泥化现象明显,施工难度极大。介绍了施工中所采用的降水、围岩加固、加强支护等措施和方法,有效保证了工期和施工质量。施工经验可供同类工程参考。%The third and fourth oblique shafts and the section of the main body of the Humaling Tunnel go through the third system under-cemented fine-powdered sandy rock stratum,where the rock of the stratum is soft and underground water is rich,owing to which gush of underground water and flowing sand arise here and there,and the slurrying phenomenon of the work face is obvious,which make the construction extremely difficult.Introduced in the paper are technical measures and methods related to draining underground water,solidifying the surrounding rock and strengthening the support,etc.,all of which help ensure the construction duration and quality.The experience of the project may serve as a useful reference for other projects of the same type.

  14. Literature Review of Lexical Cohesion Theory

    Institute of Scientific and Technical Information of China (English)

    XIAO Fuliang

    2016-01-01

    Lexical cohesion theory contributes to its patterns and cohesive functions in English texts. Different linguists have different views on lexical cohesion are introduced and its patterns are guided in detail as well. A full understanding of lexical cohesion can help better comprehend English texts.

  15. [Group cohesion: a concept analysis].

    Science.gov (United States)

    Lin, Yen-Ru; Chen, Yu-Jung; Tzeng, Wen-Chii; Chou, Kuei-Ru

    2007-10-01

    Group cohesion is considered an essential condition for achieving a successful treatment team. High cohesion groups more readily reach their goals, with group members also feeling more secure about their functions and contributions. In clinical practice, nurses use group teaching and group therapy to help patient and family members gain knowledge and skills related to illness treatment and recuperation. Effective group leadership helps minimize non-productive time and manpower and enhance interpersonal interaction. A further advantage of group cohesion is that the more effective administration of nursing programs that results can raise the profession level of staffs and reduce turnover. Walker and Avant (1995) employ concept analysis to use defining attributes in order to apply the same definition and communication to the same profession. The purpose of this paper was to apply this methodology to an analysis of group cohesion. Steps used include a review of the literature on conceptual definitions of group cohesion, a determination of defining attributes, model construction, identification of borderline, contrary, and related cases, and identification of antecedents and consequences and empirical tools. It is hoped that this analysis can help nursing staff to gain a better understanding of the concept of group cohesion and to apply such to clinical practice and nursing administration.

  16. Structural Characteristics and Properties of Precious Metal Powders and Copper Powder Prepared by High-speed Centrifugal Atomization Technique

    Institute of Scientific and Technical Information of China (English)

    XIE Ming; YANG You-cai; LI Yu-shen; ZHANG Jian-kan; FU Shi-ji; SHI Qing-nan

    2007-01-01

    The principle and characteristics of the rapidly solidified centrifugal atomization technique are studied in present paper. It has been widely used to make fine, rapidly solidified precious metal powders for application as the electrical engineering materials, conductive coatings for electromagnetic shielding and brazing alloys. The silver powder, copper powder and some precious metal alloys powders are prepared by the new method. A comparative analysis is carried out with the conventional electrolytic silver powder and chemical deposition silver powder. The results show that rapidly solidified powders are fine and have higher solid solubility of the alloying elements, and their alloys have excellent properties in various aspects.

  17. Discrete element simulations and experiments: toward applications for cohesive powders

    NARCIS (Netherlands)

    Imole, Olukayode Isaiah

    2014-01-01

    Granular materials are omnipresent in nature and widely used in various industries ranging from food and pharmaceutical to agriculture and mining – among others. It has been estimated that about 10% of the world’s energy consumption is used in the processing, storage and transport of granular

  18. Effect of particle shape of active pharmaceutical ingredients prepared by fluidized-bed jet-milling on cohesiveness.

    Science.gov (United States)

    Fukunaka, Tadashi; Sawaguchi, Kohta; Golman, Boris; Shinohara, Kunio

    2005-05-01

    Milling is a common procedure to improve bioavailability of many active pharmaceutical ingredients (APIs), which typically have low solubility in water. But such micronization can yield an increase in the cohesiveness of particles. Although particle cohesiveness is desirable for tablet strength in the subsequent formulation process, increased particle cohesiveness can lead to operational difficulties in a milling equipment due to compaction of particles inside. In this article, the impact of milling via a fluidized-bed jet-mill on the cohesive strength and interparticle force was studied using Ethenzamide as a pharmaceutical model compound. As a result, the particle shape was found to affect both the tensile strength of powder bed and the interparticle cohesive force. A powder bed, having relatively high void fraction by direct tensile test, shows a positive correlation between the cohesive force and the particle sphericity, while powders with low void fraction by diametral compression test show a positive correlation between the cohesive force and the angularity of the particle.

  19. The cohesiveness of sourcing teams

    DEFF Research Database (Denmark)

    Lidegaard, Nina

    2015-01-01

    , the practical implementation is often unsuccessful leading to poor performance. Originating in PSM literature, factors influencing sourcing team performance are categorised into three: top management support, organisational structures, and those related to team members. In this paper, the concept...... of cohesiveness is introduced as an explanatory factor and, consequently, linkages between team cohesiveness and team performance are proposed.......Sourcing teams are introduced as an approach to achieving the interdepartmental integration necessary for companies to address the complexity of strategic sourcing. Companies aim at facilitating teams capable of balancing the goals and tasks of the team with departmental expectations; however...

  20. Unit Cohesion and the Surface Navy: Does Cohesion Affect Performance

    Science.gov (United States)

    1989-12-01

    Relationship of Group Cohe- sion to Group Performance: A Research Integration Attempt, by L. W. Oliver, A199069, July 1988. Cartwright , D., "The Nature of...Group Cohesiveness," in Darwin Cart- wright and Alvin Zander, eds., Group Dynamics: Research and Theory, New York: Harper and Row, 1968. Gujarati, D. N

  1. Forms of cohesion in confinement institutions

    Directory of Open Access Journals (Sweden)

    Ekaterina D. Slobodenyuk

    2015-12-01

    Full Text Available Objective to identify the diversity of cohesion forms in confinement institutions. Methods qualitative analyses based on indepth semistructured interviews. Results the study included adaptation of Western methodologies of the cohesion phenomenon analysis to the Russian reality and operationalization of the moral bases of group cohesion. This served as the bases for designing a guide for indepth semistructured interviews 10 interviews were conducted with people recently released from general and strict regime colonies. Content analysis of the interviews revealed a number of structural sections that demonstrate the diversity of cohesion forms alongside with one that is most meaningful to the prisoners and therefore the most well perceived and articulated by respondents. Analysis of the latter allowed to identify a set of groups showing different degree and nature of cohesion. By the degree of cohesion one can identify the poorly cohesive groups quotloutsquot moderately cohesive quotredsquot quotthievesquot and highly cohesive quotfightersquot. By the nature of cohesion in the prisonersrsquo community there are both groups united on the basis of social morality quotredsquot quotthievesquot and groups demonstrating a high degree of cohesion based on the social justice morality quotfightersquot. A detailed analysis of the latter group also showed that the cohesion can have both traits of morality social justice and features of social order moral. Scientific novelty using the sociopsychological theory of the moral motives in determining the bases of cohesion. Practical significance the research results can be applied for the development of sociopsychological techniques for the penal system reform.

  2. Cohesive Function of Lexical Repetition in Text

    Institute of Scientific and Technical Information of China (English)

    张莉; 卢沛沛

    2013-01-01

    Lexical repetition is the most direct form of lexical cohesion,which is the central device for making texts hang together. Although repetition is the most direct way to emphasize,it performs the cohesive effect more apparently.

  3. Writing Quality, Coherence, and Cohesion.

    Science.gov (United States)

    McCulley, George A.

    1985-01-01

    Using a random sample of 493 persuasive papers written by 17-year-olds during the 1978-79 National Assessment of Educational Progress writing evaluation, a study investigated the relationships among features of textual cohesion and primary trait assessments of writing quality and coherence, with manuscript length held statistically constant. (HOD)

  4. The Ethics of Social Cohesion

    Science.gov (United States)

    Heuser, Brian L.

    2005-01-01

    With trust as its antecedent, social capital comprises the potential capacities of a people to prosper. Building on the presence of social capital, social cohesion involves the internalization of social ethics and constitutes the level of realized propensity among citizens to engage in virtuous behavior for the common good. This theory elaboration…

  5. Developing Indicators of Territorial Cohesion

    DEFF Research Database (Denmark)

    Gallina, Andrea; Farrugia, Nadia

    Territorial cohesion, broadly defined as the possibility for the population living in a territory to access services of general economic interest, is a relatively new concept, but which is increasingly gaining importance in the academic and policy-making spheres, especially in the European Union...

  6. Effect of detergent on powder triboelectrification.

    Science.gov (United States)

    Murtomaa, Matti; Ojanen, Kalle; Laine, Ensio; Poutanen, Jutta

    2002-12-01

    Triboelectrification of pharmaceutical powders during processing and manufacture may cause adhesion/cohesion effects, reduce fill and dose uniformity, affect powder flow and packing behaviour and even obstruct the manufacturing of the product. This paper presents the results of an experimental study on the triboelectrification of microcrystalline cellulose in contact with stainless steel pipes washed with several different detergents. Detergents and their concentrations were chosen to be similar to typical industrial manufacturing stages. The adhesion of powder to the surface had a considerable effect on the triboelectrification process. Therefore, polystyrene spheres were also charged in a similar way and the results were compared with the powder charging results. The results clearly indicate that detergent contamination on the pipe surface has a considerable effect on the generated charge. The detergents and powders used could be arranged in a triboelectric series with only one exception.

  7. On Cohesion of I have a Dream

    Institute of Scientific and Technical Information of China (English)

    姬丽霞; 郑斌

    2009-01-01

    Cohesion theory was proposed by Halliday and Hasan in 1976, and then developed by them in 1985. Through the analysis of cohesive devices of the famous speech I have a Dream from the aspects of grammatical cohesion, lexical cohesion and parallelism, this paper proves that it not only functions as a device to make the text more compact, but could make the text more expressive and persuasive.

  8. Social Cohesion as the Goal: Can Social Cohesion Be Directly Pursued?

    Science.gov (United States)

    Koonce, Kelly A.

    2011-01-01

    This article establishes an understanding of social cohesion in general and discusses organizations and activities that are known to promote social cohesion before introducing organizations that claim to work toward social cohesion as one of their main priorities. The Council of Europe's Directorate General of Social Cohesion represents a…

  9. Cohesion in Written Business Discourse: Some Contrasts.

    Science.gov (United States)

    Johns, Ann M.

    1980-01-01

    Describes study to determine whether "constellations" of cohesive items occur in letters, reports, and textbooks. Concludes cohesive elements can be identified in each type of discourse but generalizations cannot be made about cohesive features in broad classes of applied and academic English for Business and Economics (EBE) discourse. (Author/BK)

  10. Analysis of textual Cohesion in News Report

    Institute of Scientific and Technical Information of China (English)

    刘盛兰

    2014-01-01

    Cohesion embodies the non-structural resources in English discourse and indicates the latent continuity existing in the text.On the basis of cohesion theory,this paper analyzes textual cohesion of the selected news reports form BBC website,in order to explore the way of structuring the text and realizing the meaning of the text.

  11. Social Cohesion, Social Capital and the Neighbourhood.

    Science.gov (United States)

    Forrest, Ray; Kearns, Ade

    2001-01-01

    Outlines key dimensions of social cohesion, exploring whether societies are facing a new crisis in this area. Examines where contemporary residential neighborhoods fit into social cohesion debates, particularly regarding the interaction between social cohesion and social capital. Outlines key debates over social capital, showing how it can be…

  12. Calculation of cohesive energy of actinide metals

    Institute of Scientific and Technical Information of China (English)

    钱存富; 陈秀芳; 余瑞璜; 耿平; 段占强

    1997-01-01

    According to empirical electron theory of solids and molecules (EET), an equation for calculating the cohesive energy of actinide metals is given, the cohesive energy of 9 actinide metals with known crystal structure is calculated, which is identical with the experimental values on the whole, and the cohesive energy of 6 actinide metals with unknown crystal structure is forecast.

  13. Analysis of Cohesion inOliver Twist

    Institute of Scientific and Technical Information of China (English)

    程文文

    2016-01-01

    Cohesion is an important concept in the study of stylistics. This thesis aims to study the applications of cohesion in the Charles Dicken’ world-famous novelOliver Twist, including both the grammatical and lexical cohesive devices in the work.

  14. Slip casting nano-particle powders for making transparent ceramics

    Science.gov (United States)

    Kuntz, Joshua D.; Soules, Thomas F.; Landingham, Richard Lee; Hollingsworth, Joel P.

    2011-04-12

    A method of making a transparent ceramic including the steps of providing nano-ceramic powders in a processed or unprocessed form, mixing the powders with de-ionized water, the step of mixing the powders with de-ionized water producing a slurry, sonifing the slurry to completely wet the powder and suspend the powder in the de-ionized water, separating very fine particles from the slurry, molding the slurry, and curing the slurry to produce the transparent ceramic.

  15. Structural characterization of Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} as a function of temperature using neutron powder diffraction and extended X-ray absorption fine structure techniques

    Energy Technology Data Exchange (ETDEWEB)

    Mansour, A. N. [Naval Surface Warfare Center, Carderock Division, West Bethesda, Maryland 20817 (United States); Wong-Ng, W. [Materials Measurement Science Division National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Huang, Q. [Center for Neutron Research National Institute of Standards and Technology, Gaithersburg, Maryland 20899 (United States); Tang, W. [Zhejiang Sci-Tech University, Hangzhou, Zhejiang 310018 (China); Thompson, A.; Sharp, J. [Marlow Industries, Inc Dallas, Texas 75238 (United States)

    2014-08-28

    The structure of Bi{sub 2}Te{sub 3} (Seebeck coefficient Standard Reference Material (SRM™ 3451)) and the related phase Sb{sub 2}Te{sub 3} have been characterized as a function of temperature using the neutron powder diffraction (NPD) and the extended X-ray absorption fine structure (EXAFS) techniques. The neutron structural studies were carried out from 20 K to 300 K for Bi{sub 2}Te{sub 3} and from 10 K to 298 K for Sb{sub 2}Te{sub 3}. The EXAFS technique for studying the local structure of the two compounds was conducted from 19 K to 298 K. Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} are isostructural, with a space group of R3{sup ¯}m. The structure consists of repeated quintuple layers of atoms, Te2-M-Te1-M-Te2 (where M = Bi or Sb) stacking along the c-axis of the unit cell. EXAFS was used to examine the bond distances and static and thermal disorders for the first three shells of Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3} as a function of temperature. The temperature dependencies of thermal disorders were analyzed using the Debye and Einstein models for lattice vibrations. The Debye and Einstein temperatures for the first two shells of Bi{sub 2}Te{sub 3} are similar to those of Sb{sub 2}Te{sub 3} within the uncertainty in the data. However, the Debye and Einstein temperatures for the third shell of Bi-Bi are significantly lower than those of the third shell of Sb-Sb. The Einstein temperature for the third shell is consistent with a soft phonon mode in both Bi{sub 2}Te{sub 3} and Sb{sub 2}Te{sub 3}. The lower Einstein temperature of Bi-Bi relative to Sb-Sb is consistent with the lower value of thermal conductivity of Bi{sub 2}Te{sub 3} relative to Sb{sub 2}Te{sub 3}.

  16. A centrifuge method to measure particle cohesion forces to substrate surfaces : The use of a force distribution concept for data interpretation

    NARCIS (Netherlands)

    Nguyen, Thanh T.; Rambanapasi, Clinton; de Boer, Anne H.; Frijlink, Henderik W.; Ven, Peter M. V. D.; de Vries, Joop; Busscher, Henk J.; Maarschalk, Kees V. D. Voort

    2010-01-01

    Adhesion, agglomeration and de-agglomeration of micronized particles and larger carrier particles are of special importance during manufacturing of pharmaceutical products when the inherent cohesion property of fine particles challenges the content uniformity of dry mixtures. To characterize particl

  17. A centrifuge method to measure particle cohesion forces to substrate surfaces: The use of a force distribution concept for data interpretation

    NARCIS (Netherlands)

    Nguyen, T.T.; Rambanapasi, C.; Boer, A.H.de; Frijlink, H.W.; Ven, P.M.V.D.; Vries, J.de; Busscher, H.J.; Maarschalk, K.V.V.

    2010-01-01

    Adhesion, agglomeration and de-agglomeration of micronized particles and larger carrier particles are of special importance during manufacturing of pharmaceutical products when the inherent cohesion property of fine particles challenges the content uniformity of dry mixtures. To characterize particl

  18. Persistent telomere cohesion triggers a prolonged anaphase.

    Science.gov (United States)

    Kim, Mi Kyung; Smith, Susan

    2014-01-01

    Telomeres use distinct mechanisms (not used by arms or centromeres) to mediate cohesion between sister chromatids. However, the motivation for a specialized mechanism at telomeres is not well understood. Here we show, using fluorescence in situ hybridization and live-cell imaging, that persistent sister chromatid cohesion at telomeres triggers a prolonged anaphase in normal human cells and cancer cells. Excess cohesion at telomeres can be induced by inhibition of tankyrase 1, a poly(ADP-ribose) polymerase that is required for resolution of telomere cohesion, or by overexpression of proteins required to establish telomere cohesion, the shelterin subunit TIN2 and the cohesin subunit SA1. Regardless of the method of induction, excess cohesion at telomeres in mitosis prevents a robust and efficient anaphase. SA1- or TIN2-induced excess cohesion and anaphase delay can be rescued by overexpression of tankyrase 1. Moreover, we show that primary fibroblasts, which accumulate excess telomere cohesion at mitosis naturally during replicative aging, undergo a similar delay in anaphase progression that can also be rescued by overexpression of tankyrase 1. Our study demonstrates that there are opposing forces that regulate telomere cohesion. The observation that cells respond to unresolved telomere cohesion by delaying (but not completely disrupting) anaphase progression suggests a mechanism for tolerating excess cohesion and maintaining telomere integrity. This attempt to deal with telomere damage may be ultimately futile for aging fibroblasts but useful for cancer cells.

  19. A Heuristic Examination of Cohesive Sediment Bed Exchange in Turbulent Flows

    Science.gov (United States)

    2011-01-01

    1962. Flume studies of the transport of sediment in estuarial shoaling processes . Final Report. Hydraulic Engineering Laboratory and Sanitary...of flocculated fine sediments. J. Hydraul . Res. 4, 361–381. Migniot, P.C., 1968. A study of the physical properties of different very fine sediments...J.C., 1998. A simple model for turbulence induced flocculation of cohesive sediment. J. Hydraul . Res. 36 (3), 309–326. Winterwerp, J.C., van Kesteren

  20. A Formula for Building Cohesion

    Science.gov (United States)

    2007-11-02

    in World.War II to feel the tremendous outpouring of warmth , friendebip, banding and esprit that exist among its members. They"had cohesion. "In the... interpersonal relationships. Furthermore, if the company comniader elects to provide compensatorzy time for the company but cannot allow the entire unit...that a unit commander can devise to provide settings for interpersonal relationships to flourish. Having provided for face-to-face relationships to

  1. Rheological Properties and Incipient Motion of Cohesive Sediment in the Haihe Estuary of China

    Institute of Scientific and Technical Information of China (English)

    BAI Yu-chuan(白玉川); NG Chiu-on; SHEN Huan-ting(沈涣庭); WANG Shang-yi(王尚毅)

    2002-01-01

    The Haihe cohesive sediment, which is typical in China, is studied systematically for its basic physical and incipientmotion properties. Following the requirements of dredging works in the Haihe Estuary, cohesive sediment samples weretaken from three locations. Laboratory experiments were conducted to determine the rheological properties of these sam-ples and to examine the incipient motion of the cohesive sediment. It is found that the cohesive sediment has an obviousyield stress τb, which increases with the mud density in a manner of an exponential function, and so does the viscosityparameter η. The cohesive sediment behaves like a Bingham fluid when its density is below 1.38 ~ 1.40 g/cm3, andwhen denser than these values, it may become a power-law fluid. The incipient motion experiment also revealed that theincipient velocity of the cohesive sediment increases with the density in an exponential manner. Therefore, the incipientmotion is primarily related to the density, which is different from the case for non-cohesive sediment in which the incipi-ent motion is correlated with the diameter of sand particles instead. The incipient motion occurs in two different ways de-pending on the concentration of mud in the bottom. For sufficiently fine particles and a concentration lower than1.20 g/cm3, the cohesive sediment appears as fluidized mud, and the incipient motion is in the form of instability of aninternal wave. For a higher concentration, the cohesive sediment appears as general quasi-solid-mud, and the incipientmotion can be described by a series of extended Shields curves each with a different porosity for newly deposited alluvial mud.

  2. Determination of Dispersion of Zucchini and Cabbage Powders

    Directory of Open Access Journals (Sweden)

    M.I. Pogozhyh

    2013-07-01

    Full Text Available Particle size of cabbage and zucchini powders was determined by microscopy. It is shown that under the identical conditions of drying, grinding and other stages of the process, the cabbage powder has a higher content of fine fraction. Promising application of cabbage and zucchini powders in restaurant industry is indicated. Case diagram of the received production use is developed.

  3. Investigation into process-induced de-aggregation of cohesive micronised API particles.

    Science.gov (United States)

    Hoffmann, Magnus; Wray, Patrick S; Gamble, John F; Tobyn, Mike

    2015-09-30

    The aim of this study was to assess the impact of unit processes on the de-aggregation of a cohesive micronised API within a pharmaceutical formulation using near-infrared chemical imaging. The impact on the primary API particles was also investigated using an image-based particle characterization system with integrated Raman analysis. The blended material was shown to contain large, API rich domains which were distributed in-homogeneously across the sample, suggesting that the blending process was not aggressive enough to disperse aggregates of micronised drug particles. Cone milling, routinely used to improve the homogeneity of such cohesive formulations, was observed to substantially reduce the number and size of API rich domains; however, several smaller API domains survived the milling process. Conveyance of the cone milled formulation through the Alexanderwerk WP120 powder feed system completely dispersed all remaining aggregates. Importantly, powder feed transmission of the un-milled formulation was observed to produce an equally homogeneous API distribution. The size of the micronised primary drug particles remained unchanged during powder feed transmission. These findings provide further evidence that this powder feed system does induce shear, and is in fact better able to disperse aggregates of a cohesive micronised API within a blend than the blend-mill-blend step.

  4. CLAY SOIL STABILISATION USING POWDERED GLASS

    Directory of Open Access Journals (Sweden)

    J. OLUFOWOBI

    2014-10-01

    Full Text Available This paper assesses the stabilizing effect of powdered glass on clay soil. Broken waste glass was collected and ground into powder form suitable for addition to the clay soil in varying proportions namely 1%, 2%, 5%, 10% and 15% along with 15% cement (base by weight of the soil sample throughout. Consequently, the moisture content, specific gravity, particle size distribution and Atterberg limits tests were carried out to classify the soil using the ASSHTO classification system. Based on the results, the soil sample obtained corresponded to Group A-6 soils identified as ‘fair to poor’ soil type in terms of use as drainage and subgrade material. This justified stabilisation of the soil. Thereafter, compaction, California bearing ratio (CBR and direct shear tests were carried out on the soil with and without the addition of the powdered glass. The results showed improvement in the maximum dry density values on addition of the powdered glass and with corresponding gradual increase up to 5% glass powder content after which it started to decrease at 10% and 15% powdered glass content. The highest CBR values of 14.90% and 112.91% were obtained at 5% glass powder content and 5mm penetration for both the unsoaked and soaked treated samples respectively. The maximum cohesion and angle of internal friction values of 17.0 and 15.0 respectively were obtained at 10% glass powder content.

  5. Cohesion in Computer Text Generation: Lexical Substitution.

    Science.gov (United States)

    1983-05-01

    substitutions. Paul is able to generate a cohesive text which exhibits the binding of sentences through presupposition dependencies, the marking of old...lexical substitutions, Paul is able to generate a cohesive text - • which exhibits the binding of sentences through presupposition dependencies, the...problem in using these cohesive devices is that it is necessary to guarantee that they are understandable. That is, since these items refer anaphorically

  6. Characteristics and Microstructure of a Hypereutectic Al-Si Alloy Powder by Ultrasonic Gas Atomization Process

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A hypereutectic Al-Si alloy powder was prepared by ultrasonic gas atomization process. The morphologies, microstructure and phase constituent of the alloy powder were studied. The results showed that powder of the alloy was very fine and its rnicrostructure was mainly consisted of Si crystals plus intermetallic compound Al9FeSi3, which were. very fine and uniformly distributed.

  7. Preparation of silver powder through glycerol process

    Indian Academy of Sciences (India)

    Amit Sinha; B P Sharma

    2005-06-01

    High purity fine silver powder with uniform particle morphology was prepared through glycerol process. The process involves reduction of silver nitrate by glycerol under atmospheric conditions at a temperature below 175°C. Glycerol, in this process, acts as a solvent as well as a reducing agent. The powders prepared through this process were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and chemical analysis. The powders were well crystalline and contained oxygen, carbon and hydrogen as impurities. Overall purity was better than 99.9%. The yield of silver powder was better than 99%.

  8. How to freeze drop oscillations with powders

    Science.gov (United States)

    Marston, Jeremy; Zhu, Ying; Vakarelski, Ivan; Thoroddsen, Sigurdur

    2012-11-01

    We present experiments that show when a water drop impacts onto a bed of fine, hydrophobic powder, the final form of the drop can be very different from the spherical form with which it impacts. For all drop impact speeds, the drop rebounds due to the hydrophobic nature of the powder. However, we observe that above a critical impact speed, the drop undergoes a permanent deformation to a highly non-spherical shape with a complete coverage of powder, thus creating a deformed liquid marble. This powder coating acts to freeze the drop oscillations during rebound.

  9. Party cohesion in the Icelandic Althingi

    Directory of Open Access Journals (Sweden)

    Gunnar Helgi Kristinsson

    2011-12-01

    Full Text Available Institutional theories of party cohesion may be divided into "nomination theories" and "structure of the executive theories". The former seek explanations of cohesion in the way nominations are conducted, predicting that de-centralized and inclusive nominations will reduce party cohesion. The latter attempt to explain cohesion by reference to the structure of the executive, and predict that parliamentary government will increase cohesion. Party cohesion in the Icelandic Althingi has, hitherto, not been extensively studied. In this article, large amounts of data are explored to test hypotheses derived from the two theoretical approaches. The analysis is based on roll-call data dating back to 1961 and electronic voting records from 1991 onwards. The main conclusion is that party cohesion is at a high level in Iceland, despite decentralized and inclusive nominations, and hypotheses derived from nomination theories therefore find no support in our data. Hypotheses derived from "structure of the executive theories" fare much better and the main reason for high party cohesion in Iceland seems to be parliamentary government. Various features of our data, however, encourage us not to ignore other contextual features affecting party cohesion, which neither of the two institutional theories can account for satisfactorily.

  10. Psychological characteristics of group cohesion athletes.

    Directory of Open Access Journals (Sweden)

    Sheriff Sarhan

    2011-07-01

    Full Text Available The basic components of group cohesion in sport teams. An analysis of publications on cohesion within the groups where an interconnection of individual goals of each participant group with common goals and the end result of teamwork. The concept of harmony in the team sports, where the rate of group cohesion is dependent on such integrative index as psychological climate. It is established that a number of athletes to achieve high results require high cohesion, unity, value-normative orientation, deep identification and responsibility for the results of the joint group activities.

  11. Assessing Software Quality Through Visualised Cohesion Metrics

    Directory of Open Access Journals (Sweden)

    Timothy Shih

    2001-05-01

    Full Text Available Cohesion is one of the most important factors for software quality as well as maintainability, reliability and reusability. Module cohesion is defined as a quality attribute that seeks for measuring the singleness of the purpose of a module. The module of poor quality can be a serious obstacle to the system quality. In order to design a good software quality, software managers and engineers need to introduce cohesion metrics to measure and produce desirable software. A highly cohesion software is thought to be a desirable constructing. In this paper, we propose a function-oriented cohesion metrics based on the analysis of live variables, live span and the visualization of processing element dependency graph. We give six typical cohesion examples to be measured as our experiments and justification. Therefore, a well-defined, well-normalized, well-visualized and well-experimented cohesion metrics is proposed to indicate and thus enhance software cohesion strength. Furthermore, this cohesion metrics can be easily incorporated with software CASE tool to help software engineers to improve software quality.

  12. Automated Behavior and Cohesion Assessment Tools Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An important consideration of long duration space flight operations is interpersonal dynamics that effect crew cohesion and performance. Flight surgeons have stated...

  13. Application of Cohesion Theory in Listening Text Analysis

    Institute of Scientific and Technical Information of China (English)

    董天; 牛敬敏

    2014-01-01

    Based on discourse cohesion,this thesis adopts phonological cohesion,lexical cohesion,structure cohesion and logical con-junction as the theoretical guidance and analyzes the listening texts and proves that multidimensional cohesion plays an important role in listen-ing comprehension.

  14. Cohesive Harmony and Textual Quality: An Empirical Investigation.

    Science.gov (United States)

    Fang, Zhihui; Cox, Beverly E.

    1998-01-01

    Finds developmental changes in both cohesive harmony and holistic writing quality in the writing of first graders, suggesting that cohesive harmony may be a sensitive measure of textual quality. Finds no consistent relationship between measures of cohesive ties and cohesive harmony. Suggests that cohesive harmony is a viable tool for discourse…

  15. Developing Team Cohesion: A Quasi-Field Experiment

    Science.gov (United States)

    2004-03-01

    the extent of motivation to accomplishing the organization’s goals and Group Characteristics Group Processes Cohesion Social Task...Workload Sharing Cohesion Social (Bonding) Task Effectiveness Spirit Pride Environment Stressful activities Social activities Individual...n Task Cohesion Social Cohesion Affective Horizontal Bonding Figure 3. Growth of cohesion over time for seven week familiarity period and one week

  16. Regions and the Territorial Cohesion

    Directory of Open Access Journals (Sweden)

    Ioan Ianos

    2013-08-01

    Full Text Available Territorial cohesion is an important target of European Union, constantly promoted by its institutions and their representatives. In the context of the Europe 2020 strategy, one of the most important support documents, the region represents a very important issue, being considered to be the key to its successfulness. The region is seen as a support for the smart growth and all the operational policy concepts try to make use of the spatial potential, by taking better account of the territorial specificities. Two main questions play attention: the need to transform the present-day developmental regions into administrative ones is a priority? What kind of regionalization it must to be promoted? Correlating these issues with already defined territorial cohesion, the administrative region is a real tool for the future territorial development. The experience of the last 14 years asks urgently the building of a new territorial administrative reform, giving competences to regions. For instant, each development region is a construction resulted from a free association of the counties. Their role in the regional development is much reduced one, because their regional councils are not elected; decisions taken at this level are consultative for the social, economical, cultural or political actors.

  17. Preparation of Ultra-fine Salbutamol Sulfate Particles by Reactive Precipitation and Characterization of Dry Powder Inhalant%反应沉淀法制备超细硫酸沙丁胺醇颗粒及其粉雾剂的表征

    Institute of Scientific and Technical Information of China (English)

    续京; 刘晓林; 陈建峰

    2008-01-01

    The preparation of ultra.fine particles of salbutamol sulphate(SS)was accomplished with a reactive precipitation pathway,in Which salbutamo]and sulphuric acid were used as reactants wlth the solvents of ethanol.The effects of sulphuric acid concentration.reaction temperature,stirring rate,and reaction time on the Size of the particle were investigated.A binary mixture composed of lactose and SS was prepared to evaluate SS.The results showed that ultra-fine SS particles with controlled diameters ranging between 3 grn and 0.8 μm and with a narrow distribution could be achieyed.The morphology consisting of clubbed particles was successfully obtained.The pu-fity of the particles reached above 98%with UV detection.The dose of dry powder inhalation was obtained by blending the particles with recrystallized lactose.which acted as a carrier.The deposition quantity of the drug in breathing tract was estimated using a twin impinger apparatus.Compared wlth the Shapuer powder(purchased in the market),the results showed that SS particles had more quantines subsided in simulative lung.

  18. Effect of thermal treatment on mechanically milled cobalt powder

    CSIR Research Space (South Africa)

    Bolokang, AS

    2012-03-01

    Full Text Available powder metallurgical route. In is the modern trend that nanocrystalline powders are used to improve the strength of cemented carbides [18-20]. Therefore, alloyed nanocrystalline carbide powders have been synthesized using MM technique [21, 22], while... caused by thin flakes of welded fine particles induced during mechanical deformation, but even after MM the powder remains a mixture of nanocrystalline and amorphous. The estimated crystalline size calculated using Sheerrer equation show that 8 and 25...

  19. Study on the HPLC Fingerprints of Spanish fly Ultra-fine Powder from Different Producing Areas and Content Determination of Cantharidin%不同产地斑蝥超微粉体的HPLC指纹图谱及斑蝥素的含量测定

    Institute of Scientific and Technical Information of China (English)

    何杰; 张水寒; 李跃辉; 万丹; 黄江波

    2014-01-01

    目的:结合斑蝥主要成分斑蝥素的含量测定与指纹图谱,比较不同产地药材化学成分的差异性,为科学评价不同产地斑蝥药材及其超微粉体的质量提供依据.方法:建立斑蝥超微粉体指纹图谱检测方法.采用高效液相色谱(HPLC)法对各产地斑蝥超微粉体进行分析,采用中药色谱指纹图谱相似度评价系统软件比较指纹图谱的相似度,采用SPSS 13.0统计软件对10批样品进行聚类分析,并测定斑蝥素含量.结果:不同产地斑蝥超微粉体指纹图谱有较大相似性,但斑蝥素的含量有一定的差异.聚类分析结果表明,不同产地斑蝥药材存在一定差异,但差别不大.结论:所建立的HPLC指纹图谱具有较好的精密度、重复性和稳定性,结合斑蝥素的含量,可为斑蝥药材及其超微粉体质量评价提供依据.%OBJECTIVE:To compare the difference of chemical components in Spanish fly from different producing areas on the basis of content determination and fingerprints of cantharidin,and to provide reference for quality control of S.fly from different producing areas and its ultra-fine powder.METHODS:Established the fingerprint method of S.fly ultra-fine powder.S.fly ultra-fine powder were determined by HPLC.Chromatographic Fingerprint Similarity Evaluation software was used to analyze the similarity of HPLC fingerprint.Cluster analysis was conducted in 10 batches of sample by using SPSS 13.0 software,and the content of cantharidin was determined.RESULTS:The fingerprints of S.fly ultra-fine powder from different producing areas were similar to each other.The content of cantharidin had little difference.Cluster analysis showed that there was little difference in S.fly from different producing areas.CONCLUSIONS:Established HPLC fingerprint is precise,reproducible and stable,and combined with content determination of cantharidin to provide reference for quality evaluation of S.fly and its ultra-fine powder.

  20. Textual Cohesion and Coherence in Children's Writing.

    Science.gov (United States)

    Fitzgerald, Jill; Spiegel, Dixie Lee

    1986-01-01

    Examined the relationship between cohesion and coherence in children's writing and investigated the degree to which this relationship would vary with quality of writing and grade level. Concludes that the relationship between cohesion and coherence did not vary according to quality of writing or grade level. (SRT)

  1. Academic Social Cohesion within Higher Education

    Science.gov (United States)

    Heuser, Brian L.

    2007-01-01

    This article explores the theoretical foundations of "social cohesion" as it relates to higher education institutions. In so doing it seeks (a) to understand the core elements of social cohesion--social capital, human capital and ethical behavioral norms that serve a common good--and (b) to establish a flexible framework for understanding the…

  2. Education and Social Cohesion: Higher Education

    Science.gov (United States)

    Moiseyenko, Olena

    2005-01-01

    Social cohesion is understood as the social networks and the norms of reciprocity and trustworthiness that arise from connections among individuals. When students attend higher education institutions, they go through a process of socialization, and it is vital to ensure that they acquire the core values that underpin the social cohesion. This…

  3. Networks, space, and residents' perception of cohesion.

    Science.gov (United States)

    Boessen, Adam; Hipp, John R; Smith, Emily J; Butts, Carter T; Nagle, Nicholas N; Almquist, Zack

    2014-06-01

    Community scholars increasingly focus on the linkage between residents' sense of cohesion with the neighborhood and their own social networks in the neighborhood. A challenge is that whereas some research only focuses on residents' social ties with fellow neighbors, such an approach misses out on the larger constellation of individuals' relationships and the spatial distribution of those relationships. Using data from the Twin Communities Network Study, the current project is one of the first studies to examine the actual spatial distribution of respondents' networks for a variety of relationships and the consequences of these for neighborhood and city cohesion. We also examine how a perceived structural measure of cohesion-triangle degree-impacts their perceptions of neighborhood and city cohesion. Our findings suggest that perceptions of cohesion within the neighborhood and the city depend on the number of neighborhood safety contacts as well as on the types of people with which they discuss important matters. On the other hand, kin and social friendship ties do not impact cohesion. A key finding is that residents who report more spatially dispersed networks for certain types of ties report lower levels of neighborhood and city cohesion. Residents with higher triangle degree within their neighborhood safety networks perceived more neighborhood cohesion.

  4. Sister chromatid cohesion and recombination in meiosis

    NARCIS (Netherlands)

    Heemst, van D.; Heyting, C.

    2000-01-01

    Sister chromatids are associated from their formation until their disjunction. Cohesion between sister chromatids is provided by protein complexes, of which some components are conserved across the kingdoms and between the mitotic and meiotic cell cycles. Sister chromatid cohesion is intimately link

  5. Mixed Mode cohesive law with interface dilatation

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Goutianos, Stergios

    2014-01-01

    shear stresses opposing the crack face displacements. A phenomenological Mixed Mode cohesive zone law, derived from a potential function, is developed to describe the above mentioned fracture behaviour under monotonic opening. The interface dilatation introduces two new lengths. The cohesive law...

  6. Unit Cohesion and the Impact of DADT

    Science.gov (United States)

    2010-01-01

    Janowitz, “Cohesion and Disintegra- tion in the Wehrmacht in World War II,” Public Opinion Quarterly 12, no. 2 (Summer 1948). 12. Leon Festinger ...Leon Festinger , “Informal Social Com- munication,” Psychological Review 57, no. 5 (September 1950). Unit Cohesion and the Impact of DADT Strategic

  7. Justice and Social Cohesion: Some conservative perspectives

    DEFF Research Database (Denmark)

    Pedersen, Søren Hviid

    2011-01-01

    of this problem. The argument presented in this paper will, first, take its point of departure from David Hume’s notion of sympathy and how this makes social cohesion possible. Second, it will be argued that social cohesion is a prerequisite for the existence of justice, and therefore justice is a derivative...

  8. Why are Rich Countries more Politically Cohesive?

    DEFF Research Database (Denmark)

    Dalgaard, Carl-Johan Lars; Olsson, Ola

    of other groups in society. If the gains from specialization become sufficiently large, however, a market economy will emerge. From being essentially non-cohesive under self-sufficiency, the political decision making process becomes cohesive in the market economy, as the welfare of individuals...

  9. Transfer and Cohesion in Interdisciplinary Education

    Directory of Open Access Journals (Sweden)

    Søren Harnow Klausen

    2014-06-01

    Full Text Available One of the great challenges of interdisciplinary education is to create sufficient cohesion between disciplines. It is suggested that cohesion depends on the transfer of knowledge (in a broad sense, which includes skill and competences among the disciplines involved. Some of the most characteristic types of such transfer are identified and analyzed: Transfer of factual knowledge, theories, methods, models, skills, modes of collaboration and organization, meta-competences, disciplinary self-consciousness, problem selection, framework construction and motivation. Though some of these types of transfer may have a greater or smaller potential for creating cohesion, different kinds of cohesion may serve different interests, and there is no reason to assume that e.g. joint problem solving or theoretical integration should be more conducive to cohesion than e.g. contributions to motivation or disciplinary self-consciousness.

  10. Group cohesion: Relationships with work team culture.

    Science.gov (United States)

    Sánchez, José C; Yurrebaso, Amaia

    2009-02-01

    The aim of this study was to examine the relationships between group cohesion and the perceived culture and desired culture of work teams. Two separate studies were carried out with a time interval of one year. The first study had a sample of 50 work teams belonging to different organizations and the second study had a sample of 75 work teams. We used Lindell's index of agreement to estimate the culture and cohesion variables. Multiple and hierarchical regression analysis in both studies confirmed our initial hypothesis, showing that perceived and desired culture were positively related to group cohesion, and that culture gap had a negative association with cohesion. To a lesser extent, control variables such as job tenure and gender had a positive relationship with cohesion. The implications of these results are discussed along with the importance of considering the group level as analysis.

  11. A DEM contact model for history-dependent powder flows

    Science.gov (United States)

    Hashibon, Adham; Schubert, Raphael; Breinlinger, Thomas; Kraft, Torsten

    2016-11-01

    Die filling is an important part of the powder handling process chain that greatly influences the characteristic structure and properties of the final part. Predictive modelling and simulation of the die-filling process can greatly contribute to the optimization of the part and the whole production procedure, e.g. by predicting the resulting powder compaction structure as a function of filling process parameters. The rheology of powders can be very difficult to model especially if heterogeneous agglomeration or time-dependent consolidation effects occur. We present a new discrete element contact force model that enables modelling complex powder flow characteristics including direct time-dependent consolidation effects and load history-dependent cohesion to describe the filling process of complex, difficult to handle powders. The model is demonstrated for simple flow and an industrial powder flow.

  12. Pension Insurance Cohesive Testing System

    Directory of Open Access Journals (Sweden)

    Askarbek Arzybaev

    2015-01-01

    Full Text Available Many public pension systems worldwide are experiencing difficult economic period as its economy is in the period of financial crisis which affected to the social budget sustainability.Population aging and last decade economic circumstances are the factors the pension systems should overcome for maintaining either appropriate level of benefit amount for decent life in the developed countries or minimum subsistence allowances in developing and poor countries. The only prescription how to keep the pension system resistible is its periodical renovation by testing the system on (i soundness and effectiveness within national financial and economic system, (ii appropriateness of its organization and administration, (iii compliance of parameters with international standards. The article presents Cohesive Testing System – new method of national pension systems testing and indexing based on international standards of pension security and new CTS indices of the researched set of pension systems.

  13. Dry powder platform for pulmonary drug delivery

    Institute of Scientific and Technical Information of China (English)

    Derek Ivan Daniher; Jesse Zhu

    2008-01-01

    The phenomenon of particle interaction involved in pulmonary drug delivery belongs to a wide variety of disciplines of particle technology, in particular, fluidization. This paper reviews the basic concepts of pulmonary drug delivery with references to fluidization research, in particular, studies on Geldart group C powders. Dry powder inhaler device-formulation combination has been shown to be an effective method for delivering drugs to the lung for treatment of asthma, chronic obstructive pulmonary disease and cystic fibrosis. Even with advanced designs, however, delivery efficiency is still poor mainly due to powder dispersion problems which cause poor lung deposition and high dose variability. Drug particles used in current inhalers must be 1-5 μm in diameter for effective deposition in small-diameter airways and alveoli. These powders are very cohesive, have poor flowability, and are difficult to disperse into aerosol due to cohesion arising from van tier Waals attraction. These problems are well known in fluidization research, much of which is highly relevant to pulmonary drug delivery.

  14. Analysis of lexical cohesion in Lincoln’s Gettysburg Address

    Institute of Scientific and Technical Information of China (English)

    田玉红

    2014-01-01

    Lexical cohesion is one of the most important cohesions in English discourse. Lexical cohesion can explicitly express coherence in English discourse and enhance discourse coherent competence with the help of using lexical items. Based on the cohesion theory of Halliday and other linguists, this paper analyzes the classification and effect of the lexical cohesion in Lincoln's Gettysburg Address and points out that various lexical cohesive devices can play particular roles in the coherence of the discourse.

  15. Moisture Content Impact on Mechanical Properties of Selected Cohesive Soils from the Wielkopolskie Voivodeship Southern Part

    Directory of Open Access Journals (Sweden)

    Pezowicz Piotr

    2015-12-01

    Full Text Available Results of investigations of shearing resistance and compressibility of fine-grained cohesive soil from the southern part of the wielkopolskie voivodeship in relation to the increasing moisture content are presented. The analysis of two series of samples, using soil paste for the consistency index of 0.9 and 0.4–0.3 was carried out. The results imply that the increasing moisture content causes a decrease in the angle of shearing resistance and cohesion and is also reflected in the higher compressibility of the soil. It was observed that regardless of the soil consistency, the angle of shearing resistance decreases and the cohesion value and the oedometric modulus of primary (consolidation and secondary compressibility grows with the increase in the clay fraction.

  16. Mixing behaviour of cohesive and non-cohesive particle mixtures in a ribbon mixer

    Science.gov (United States)

    Musha, H.; Dong, K.; Chandratilleke, G. R.; Bridgwater, J.; Yu, A. B.

    2013-06-01

    Ribbon mixers are used in a wide range of applications involving pharmaceuticals, ceramics and cosmetics, to name a few. Here, the discrete element method is used to investigate the effect of impeller speed on the mixing behaviours of cohesive as well as non-cohesive particle mixtures in a ribbon mixer, which has a horizontal cylindrical vessel. The mixing behaviours are characterized by particle-scale and macroscopic mixing indexes. Simulations show that the mixing rate increases with the impeller speed for both the cohesive and non-cohesive mixtures up to a certain speed, beyond which it showed a reduction. There is a possibility that the mixture quality becomes poorer at higher impeller speeds for the non-cohesive particles, but it was not the case with the cohesive particles. Inspection of velocity fields shows that many local recirculation regions exist in the case of non-cohesive particle mixing, preventing the overall mixing. By contrast, in the case of the cohesive mixture, there exists a circumferential motion about the shaft and a convective motion in the horizontal axial direction, improving the particle mixing. Force analyses are also carried out, which show that the particle contact forces increase with the impeller speed for non-cohesive particles, but in the case of cohesive particles, they increase initially with the impeller speed, and then show a reduction after a certain speed. The results will be useful in selecting operation conditions of a ribbon mixer.

  17. The Effect of Wasted Magnesia-chrome Fine Powder Addition on Properties of Alumina-magnesia Castable%废镁铬砖细粉对铝镁浇注料性能的影响

    Institute of Scientific and Technical Information of China (English)

    崔庆阳; 黄鹏; 吴林林; 毛晓刚; 李有奇

    2012-01-01

    Alumina-magnesia Castables were prepared using brown corundum (8 ~ lmm), white corundum ( 2) > 94%) as matrix, p-Al2O3 powder for the binder, sodium hexametaphosphate as depersant, to study the waste magnesium-chromium powder equivalent instead of fused magnesia, the mass fraction is (respectively 0,1%, 2%, 3%) on properties of aluminum-magnesium castable. The results showed that: with the increase of waste magnesia-chrome brick powder, the intensity of sample after drying or burning increased, and the volume density, but apparent porosity decreased, the rate of linear change decreasing; but decrease in thermal shock resistance, rupture resistence at high temperature increased slightly, mainly according to the amount of the solid solution formed at high temperature by waste magnesia-chrome brick powder and alumina powder.%以棕刚玉(8~1mm)、白刚玉(≤3mm)为骨料,以白刚玉细粉(≤0.045 mm)、α-Al2O3微粉(≤5μm,d50=2.01 μm)、电熔镁砂细粉(≤ 0.074mm)、硅灰(w(SiO2)>94%)为基质,以ρ-Al2O3微粉为结合剂,以六偏磷酸钠为减水剂制备铝镁质浇注料,采用废镁铬砖细粉等量代替电熔镁砂细粉,研究了废镁铬砖细粉质量分数(分别为0、1%、2%、3%)对铝镁浇注料性能的影响.试验结果表明:随着废镁铬砖细粉加入量的增大,试样的烘后和烧后强度均提高,体积密度增大,显气孔率减小、线变化率先增大后减小;但抗热震性有所降低、高温抗折强度稍有增大,这主要与高温下废镁铬砖细粉和刚玉细粉生成多种固溶体的量有关.

  18. Anne Fine

    Directory of Open Access Journals (Sweden)

    Philip Gaydon

    2015-04-01

    Full Text Available An interview with Anne Fine with an introduction and aside on the role of children’s literature in our lives and development, and our adult perceptions of the suitability of childhood reading material.Since graduating from Warwick in 1968 with a BA in Politics and History, Anne Fine has written over fifty books for children and eight for adults, won the Carnegie Medal twice (for Goggle-Eyes in 1989 and Flour Babies in 1992, been a highly commended runner-up three times (for Bill’s New Frock in 1989, The Tulip Touch in 1996, and Up on Cloud Nine in 2002, been shortlisted for the Hans Christian Andersen Award (the highest recognition available to a writer or illustrator of children’s books, 1998, undertaken the positon of Children’s Laureate (2001-2003, and been awarded an OBE for her services to literature (2003. Warwick presented Fine with an Honorary Doctorate in 2005.Philip Gaydon’s interview with Anne Fine was recorded as part of the ‘Voices of the University’ oral history project, co-ordinated by Warwick’s Institute of Advanced Study.

  19. Experimental study on fluidization of micronic powders

    OpenAIRE

    Alavi, Shila; Caussat, Brigitte

    2005-01-01

    The fluidization behavior of yttrium oxide (Y2O3) powders of high density and micronic diameter belonging to the group C of Geldart’s classification has been investigated. Large interparticle forces lead to bed cracking, slugging and channelling, and cause the powder not to fluidize consistently. Different fluidization technologies have been tested, such as mechanical agitated fluidization, vibrated fluidization and addition of easyto-fluidize large particles to fine particles. The qual...

  20. Natural disasters and indicators of social cohesion.

    Science.gov (United States)

    Calo-Blanco, Aitor; Kovářík, Jaromír; Mengel, Friederike; Romero, José Gabriel

    2017-01-01

    Do adversarial environmental conditions create social cohesion? We provide new answers to this question by exploiting spatial and temporal variation in exposure to earthquakes across Chile. Using a variety of methods and controlling for a number of socio-economic variables, we find that exposure to earthquakes has a positive effect on several indicators of social cohesion. Social cohesion increases after a big earthquake and slowly erodes in periods where environmental conditions are less adverse. Our results contribute to the current debate on whether and how environmental conditions shape formal and informal institutions.

  1. A FRAMEWORK TO MEASURE CLASS COHESION

    Institute of Scientific and Technical Information of China (English)

    XuBaowen; ChenZhenqiang; 等

    2003-01-01

    Chasses are the basic modules in Object-Oriented(OO)softvare,which consist of attributed and methods.Thus,in OO environment,the cohesion is mainly about how tightly the attributed and methods of classes cohere with each other.This letter discusses the relationships between attributes and attributes,attributes and methods,methods and methods of a class,and the properties of these relationships.Based on these properties,the letter proposes a new framework to measure the cohesion of a class.The approach overcomes the limitations of previous class cohesion measures,which comsider only one or two of the three relationships in class.

  2. Measuring Class Cohesion Based on Dependence Analysis

    Institute of Scientific and Technical Information of China (English)

    Zhen-Qiang Chen; Bao-Wen Xu; Yu-Ming Zhou

    2004-01-01

    Classes are the basic modules in object-oriented (OO) software, which consist of attributes and methods. Thus, in OO environment, the cohesion is mainly about the tightness of the attributes and methods of classes. This paper discusses the relationships between attributes and attributes, attributes and methods, methods and methods of a class based on dependence analysis. Then the paper presents methods to compute these dependencies. Based on these, the paper proposes a method to measure the class cohesion, which satisfies the properties that a good measurement should have. The approach overcomes the limitations of previous class cohesion measures, which consider only one or two of the three relationships in a class.

  3. A FRAMEWORK TO MEASURE CLASS COHESION

    Institute of Scientific and Technical Information of China (English)

    Xu Baowen; Chen Zhenqiang; Zhou Yuming

    2003-01-01

    Classes are the basic modules in Object-Oriented (OO) software, which consist of attributes and methods. Thus, in OO environment, the cohesion is mainly about how tightly the attributes and methods of classes cohere with each other. This letter discusses the relationships between attributes and attributes, attributes and methods, methods and methods of a class,and the properties of these relationships. Based on these properties, the letter proposes a new framework to measure the cohesion of a class. The approach overcomes the limitations of previous class cohesion measures, which consider only one or two of the three relationships in a class.

  4. STUDY ON STARTING VELOCITY OF COHESIVE SEDIMENTATION

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this paper, with the starting velocity experiments of natural cohesive sedimentation, the author proposes an assumption concerning the starting mechanism of cohesive sedimentation and gives a formula to determine the starting velocity of compact clay. It is pointed out that the fluctuating function of flow is a main factor for the starting of sedimentation. And the component and the structure of cohesive sedimentation are also the affecting factors for the starting. Consequently, the study shows that modern results of soil mechanics, clay mineralogy and fluid mechanics are helpful in the investigation of this kind of engineering problem.

  5. Natural disasters and indicators of social cohesion

    Science.gov (United States)

    Calo-Blanco, Aitor; Kovářík, Jaromír; Mengel, Friederike; Romero, José Gabriel

    2017-01-01

    Do adversarial environmental conditions create social cohesion? We provide new answers to this question by exploiting spatial and temporal variation in exposure to earthquakes across Chile. Using a variety of methods and controlling for a number of socio-economic variables, we find that exposure to earthquakes has a positive effect on several indicators of social cohesion. Social cohesion increases after a big earthquake and slowly erodes in periods where environmental conditions are less adverse. Our results contribute to the current debate on whether and how environmental conditions shape formal and informal institutions. PMID:28591148

  6. Cohesion Metrics for Ontology Design and Application

    Directory of Open Access Journals (Sweden)

    Haining Yao

    2005-01-01

    Full Text Available Recently, domain specific ontology development has been driven by research on the Semantic Web. Ontologies have been suggested for use in many application areas targeted by the Semantic Web, such as dynamic web service composition and general web service matching. Fundamental characteristics of these ontologies must be determined in order to effectively make use of them: for example, Sirin, Hendler and Parsia have suggested that determining fundamental characteristics of ontologies is important for dynamic web service composition. Our research examines cohesion metrics for ontologies. The cohesion metrics examine the fundamental quality of cohesion as it relates to ontologies.

  7. Object Discovery via Cohesion Measurement.

    Science.gov (United States)

    Guo, Guanjun; Wang, Hanzi; Zhao, Wan-Lei; Yan, Yan; Li, Xuelong

    2017-02-16

    Color and intensity are two important components in an image. Usually, groups of image pixels, which are similar in color or intensity, are an informative representation for an object. They are therefore particularly suitable for computer vision tasks, such as saliency detection and object proposal generation. However, image pixels, which share a similar real-world color, may be quite different since colors are often distorted by intensity. In this paper, we reinvestigate the affinity matrices originally used in image segmentation methods based on spectral clustering. A new affinity matrix, which is robust to color distortions, is formulated for object discovery. Moreover, a cohesion measurement (CM) for object regions is also derived based on the formulated affinity matrix. Based on the new CM, a novel object discovery method is proposed to discover objects latent in an image by utilizing the eigenvectors of the affinity matrix. Then we apply the proposed method to both saliency detection and object proposal generation. Experimental results on several evaluation benchmarks demonstrate that the proposed CM-based method has achieved promising performance for these two tasks.

  8. Tracing cohesive sediment transportation at river mouths around Tokyo, Japan by Cesium originated from Fukushima Daiichi Power Plant

    Science.gov (United States)

    koibuchi, Y.

    2012-12-01

    Sediment transport at river mouths, which consists of suspended-load and bed-load, has not been fully understood, since bed-load transport of cohesive sand is difficult to observe. Especially, the impact of sediment transport on the total amount of fine-grained cohesive sediment has not been elucidated. Cesium-134 and cesium-137 were spread from the Fukushima Daiichi Nuclear Power Plant (FDNPP) after the earthquake of March 11 of 2011, and attached to the fine-grained sand on the land. The contaminated sand flowed into the river mouths through the rivers possibly due to the complex physical processes in estuarine areas. To evaluate the fine-grained sediment transport around Tokyo and Tokyo Bay, field observations were carried out utilizing radionuclide originated from FDNPP as an effective tracer. The cohesive sediment transport at three different river mouths around Tokyo was successfully quantified. The cohesive sediment transport deposited in the estuary was found to be greatly dependent on the land use, geometry, river discharge and salinity. In addition,the transport driven by the rainfall was minute, and its behavior was quite different from suspended solids. Although further field observations of radionuclide are necessary, it is clear that fine-grained sediment in the bay from rivers already settled on the river mouth by aggregation. The settled sand will not move even in rainfall events. Consequently, the transport of radionuclide to the Pacific Ocean may not occur.; Cesium distribution around Tokyo Bay ; Cesium Concentration in Edogawa river

  9. Textual Cohesion in Modern Standard Chinese.

    Science.gov (United States)

    Okurowski, Mary Ellen

    1989-01-01

    Presents a description of textual cohesion in Modern standard Chinese (MSC), and describes three types of relations as discourse and text features that contribute to the overall unity or coherence of a text. (24 references) (Author/VWL)

  10. A CONCEPTUAL OVERVIEW OF TERRITORIAL COHESION

    Directory of Open Access Journals (Sweden)

    MARIA VASILESCU (DUMITRASCU

    2014-12-01

    Full Text Available Territorial cohesion is a complex concept that cannot be explained by a single definition. During the previous decades, territorial issues represented, undoubtedly, subjects of interest for various policy documents, actions and funding of the European Union, but the asymmetric impact of recent global crisis, doubled by the launch of the Green Paper (2008 and its inclusion in the Lisbon Treaty, in 2009, has underlined the importance of territorial cohesion, as one of the three main pillars of the new cohesion policy. In this context, this article tries to create a holistic perspective on territorial cohesion by analyzing the available studies and to determine its relevance to the European objective of strengthening the regions, promoting territorial integration and producing coherent policies, thus contributing to the sustainable development and global competitiveness of the European Union.

  11. Cohesion in crumb rubber modified bitumen

    Directory of Open Access Journals (Sweden)

    Páez Dueñas, A.

    2006-12-01

    Full Text Available This article reports on a study of crumb rubber-mediated improvement in bitumen cohesion, analyzed with the UCL method. UCL, a procedure developed to characterize bituminous binders, evaluates the cohesion obtained by adding a certain amount of bitumen or bituminous mastic to a standard mix aggregate. This method was chosen because it can be used to assess bitumen containing crumb rubber added by either the wet or the dry mix process. In the dry mix process crumb rubber is combined with the mix as if it were a fine aggregate; i.e., crumb rubber and binder are blended during mix manufacture, laying and compaction. In the wet mix process, the binder is blended with the crumb rubber prior to mixing with the aggregate; i.e., when added to the mix, it has already been modified. The effect of digesting this dry mixed material prior to use was also analyzed in the present study. A comparison of the dry (with and without digestion and wet mix processes showed the latter to be more effective, particularly when the crumb rubber was blended with the binder via microscopic dispersion.El objetivo de este artículo es estudiar la influencia del polvo de neumático en la mejora de la cohesión proporcionada por la adición del polvo de neumático al betún mediante el método UCL. El método UCL es un procedimiento desarrollado para caracterizar ligantes bituminosos, basado en la evaluación de la cohesión dada por una cantidad determinada de un betún o un mástico bituminoso a unos áridos de granulometría establecida (mezcla patrón. Se ha empleado este método porque permite valorar al mismo tiempo los dos procedimientos de incorporación del polvo de neumático al betún: vía seca y vía húmeda.El procedimiento seco se lleva a cabo añadiendo el polvo de neumático a la mezcla como si fuera un filler, de modo que el polvo de neumático y el ligante se mezclan durante la fabricación, extendido y compactación de la mezcla. En el procedimiento h

  12. DYNAMIC COHESIVENESS IN A COMMUNICATIVE ENGLISH CLASS

    Institute of Scientific and Technical Information of China (English)

    Wang; Qiyan[1; Fu; Yanjun[2

    2001-01-01

    One of the main features of a communicative English classis activities, organized by the teacher and conducted by studentsperforming certain functions and involving different topics. Theuse of activities has gained much attention. However, the linkbetween activities seems to have been ignored. This paper is anattempt to explore the role of cohesiveness between activities incommunicative teaching. The cohesiveness can be eithermechanical or dynamic. The key is that dynamic cohesivenesscontributes to the atmosphere and effectiveness of communicativeEnglish classroom teaching.

  13. Modelling cohesive, frictional and viscoplastic materials

    Science.gov (United States)

    Alehossein, Habib; Qin, Zongyi

    2016-06-01

    Most materials in mining and civil engineering construction are not only viscoplastic, but also cohesive frictional. Fresh concrete, fly ash and mining slurries are all granular-frictional-visco-plastic fluids, although solid concrete is normally considered as a cohesive frictional material. Presented here is both a formulation of the pipe and disc flow rates as a function of pressure and pressure gradient and the CFD application to fresh concrete flow in L-Box tests.

  14. Group cohesion, task performance, and the experimenter expectancy effect.

    NARCIS (Netherlands)

    Hoogstraten, J.; Vorst, H.C.M.

    1978-01-01

    Studied the effects of cohesion on task fulfillment and explored the influence of task fulfillment on the initial level of cohesion. Within 4-person groups of undergraduates, cohesion was manipulated successfully by a triple procedure. The level of cohesion was ascertained directly after the inducti

  15. Preparation and microstructure of Al-Ni-Y powder by rapid solidification

    Institute of Scientific and Technical Information of China (English)

    黄劲松; 刘咏; 陈仕奇; 刘祖铭

    2004-01-01

    The Al-Ni Y alloy powder was prepared by rapid solidification technology of inert gas atomization. The diameter of amorphous powder is less than 12 μm. The effects of atomization gas on cooling velocity, morphology,microstructure and microhardness of powder and fine powder ratio were investigated. The results show that the mor-phology, microstructure and microhardness of powder and fine powder ratio are affected by cooling velocity changed through atomization gas. The cooling velocity of inert gas atomization is more than 1 × 104 K/s. The larger the cool-ing velocity, the finer the powder, and the smoother the surface of powder; the smaller the diameter of powder, the larger the microhardness of powder.

  16. The use of limestone powder as an alternative cement replacement ...

    African Journals Online (AJOL)

    The use of limestone powder as an alternative cement replacement material: An ... The laboratory test results revealed that up to 15% replacement of clinker by fine ... Early strength, Limestone filler, Loss on ignition, Portland limestone cement ...

  17. Powder method for detecting latent fingerprints: a review.

    Science.gov (United States)

    Sodhi, G S; Kaur, J

    2001-09-01

    The powder technique for detecting latent fingerprints involves the application of a finely divided formulation to the fingermark impression, generally with a glass-fibre or a camel hair brush. The powder gets mechanically adhered to the sweat residue defining the ridge pattern. The furrows which are devoid of the fingerprint residue, do not adhere the powder onto them. The final outcome is that the powder formulation sticks to the ridges, but is easily blown off the furrows. Since the powder is normally coloured, the ridge pattern becomes visible and the latent print is said to have developed.

  18. performance of concrete with partial replacement of fine aggregates ...

    African Journals Online (AJOL)

    user

    Key Words: compressive strength, concrete, crushed waste glass, flexural strength, setting time, water absorption and workability. ... powder as partial replacement of fine aggregates up to ... water in cement paste and reactive silica in the WG.

  19. Pyrophoric behaviour of uranium hydride and uranium powders

    Energy Technology Data Exchange (ETDEWEB)

    Le Guyadec, F., E-mail: fabienne.leguyadec@cea.f [CEA Marcoule DEN/DTEC/SDTC, 30207 Bagnols sur Ceze, BP 17171 (France); Genin, X.; Bayle, J.P. [CEA Marcoule DEN/DTEC/SDTC, 30207 Bagnols sur Ceze, BP 17171 (France); Dugne, O. [DEN/DTEC/SGCS, 30207 Bagnols sur Ceze, BP 17171 (France); Duhart-Barone, A.; Ablitzer, C. [CEA Cadarache DEN/DEC/SPUA, 13108 St. Paul lez Durance (France)

    2010-01-31

    Thermal stability and spontaneous ignition conditions of uranium hydride and uranium metal fine powders have been studied and observed in an original and dedicated experimental device placed inside a glove box under flowing pure argon. Pure uranium hydride powder with low amount of oxide (<0.5 wt.%) was obtained by heat treatment at low temperature in flowing Ar/5%H{sub 2}. Pure uranium powder was obtained by dehydration in flowing pure argon. Those fine powders showed spontaneous ignition at room temperature in air. An in situ CCD-camera displayed ignition associated with powder temperature measurement. Characterization of powders before and after ignition was performed by XRD measurements and SEM observations. Oxidation mechanisms are proposed.

  20. Validating Experimental Bedform Dynamics on Cohesive Sand-Mud Beds in the Dee Estuary

    Science.gov (United States)

    Baas, Jaco H.; Baker, Megan; Hope, Julie; Malarkey, Jonathan; Rocha, Renata

    2014-05-01

    Recent laboratory experiments and field measurements have shown that small quantities of cohesive clay, and in particular 'sticky' biological polymers, within a sandy substrate dramatically reduce the development rate of sedimentary bedforms, with major implications for sediment transport rate calculations and process interpretations from the sedimentary record. FURTHER INFORMATION Flow and sediment transport predictions from sedimentary structures found in modern estuaries and within estuarine geological systems are impeded by an almost complete lack of process-based knowledge of the behaviour of natural sediments that consist of mixtures of cohesionless sand and biologically-active cohesive mud. Indeed, existing predictive models are largely based on non-organic cohesionless sands, despite the fact that mud, in pure form or mixed with sand, is the most common sediment on Earth and also the most biologically active interface across a range of Earth-surface environments, including rivers and shallow seas. The multidisciplinary COHBED project uses state-of-the-art laboratory and field technologies to measure the erosional properties of mixed cohesive sediment beds and the formation and stability of sedimentary bedforms on these beds, integrating the key physical and biological processes that govern bed evolution. The development of current ripples on cohesive mixed sediment beds was investigated as a function of physical control on bed cohesion versus biological control on bed cohesion. These investigations included laboratory flume experiments in the Hydrodynamics Laboratory (Bangor University) and field experiments in the Dee estuary (at West Kirby near Liverpool). The flume experiments showed that winnowing of fine-grained cohesive sediment, including biological stabilisers, is an important process affecting the development rate, size and shape of the cohesive bedforms. The ripples developed progressively slower as the kaolin clay fraction in the sandy substrate

  1. Onset of Stationary Flows of a Cohesive Granular Material in a Channel

    Science.gov (United States)

    de Ryck, A.; Louisnard, O.

    The handling of bulk materials and powders in process engineering remains an important issue. To obtain reliable gravitational flows, starting and remaining stationary, the hoppers and transport channels must be designed at a scale appropriate for the friction and cohesive properties of the granular material. To describe such dense flows (the interaction with the surrounding ambient fluid is negligible compared to the weight of the particles and interparticles forces), they can be modelled by continuum mechanics, associated with a constitutive equation taking into account the friction behaviour (Mohr-Coulomb or Druger-Prager plasticity criterion). We use here the rheology proposed by Jop et al. (Nature 441: 727-730, 2006) which combines this with an associated flow rule (co-linearity of the stress and strain tensors) (Jenike, Powder Technol. 50: 229-236, 1987) and a viscous dependency of the coefficient of friction on the strain (Da Cruz et al., Phys. Rev. E 72: 021309, 2005).Using the method of characteristics to describe the flow structure (de Ryck, Granular Matter 10: 361-367, 2008), we deduce the minimal slope to obtain a stationary flow of cohesive granular materials on a finite width channel, whose lateral walls are rough or smooth. We also obtain the depth of the flow (maximal at the centre of the channel). In the case of weak cohesive materials, these results are formulated with simple analytical expressions.

  2. Research on Discharging Mechanism of Powder Mixed EDM

    Institute of Scientific and Technical Information of China (English)

    WANG Yuangang; ZHAO Fuling

    2006-01-01

    This paper presents investigations on discharging mechanism in powder mixed EDM. By analyzing the inception, growth of electrical tree and the ignition of discharges in liquid filled gap, the whole discharging process is proposed. It is explored that the reason of modification of ignition behaves by adding fine particle powders of metal or semiconductor to the working liquid.

  3. Perceived neighborhood social cohesion and stroke.

    Science.gov (United States)

    Kim, Eric S; Park, Nansook; Peterson, Christopher

    2013-11-01

    Research in the last three decades has shown that negative neighborhood factors such as neighborhood violence, noise, traffic, litter, low neighborhood socioeconomic status, and poor air quality increase the risk of poor health. Fewer studies have examined the potential protective effect that neighborhood factors can have on health, particularly stroke. We examined whether higher perceived neighborhood social cohesion was associated with lower stroke incidence after adjusting for traditional risk and psychological factors that have been linked with stroke risk. Prospective data from the Health and Retirement Study--a nationally representative panel study of American adults over the age of 50--were used. Analyses were conducted on a subset of 6740 adults who were stroke-free at baseline. Analyses adjusted for chronic illnesses and relevant sociodemographic, behavioral, and psychosocial factors. Over a four-year follow-up, higher perceived neighborhood social cohesion was associated with a lower risk of stroke. Each standard deviation increase in perceived neighborhood social cohesion was associated with a multivariate-adjusted odds ratio (O.R.) of 0.85 for stroke incidence (95% CI, 0.75-0.97, p social cohesion remained significant after adjusting for a comprehensive set of risk factors. Therefore, perceived neighborhood social cohesion plays an important role in protecting against stroke.

  4. Diffused phase transition in fine-grained bismuth vanadate ceramics

    OpenAIRE

    Shantha, K; Varma, KBR

    1999-01-01

    Nanocrystalline powders of ferroelectric bismuth vanadate, Bi4V2O11 (n-BiV), with crystallite size less than 50 nm, were obtained by mechanical milling of a stoichiometric mixture of bismuth oxide and vanadium pentoxide. The n-BiV powders on sintering yielded high-density, fine-grained ceramics with improved dielectric and polar characteristics. Dielectric studies on samples obtained from milled powders indicated that the ferroelectric-to-paraelectric phase transition temperature is strongly ...

  5. Cohesion and Hierarchy in Physically Abusive Families

    Directory of Open Access Journals (Sweden)

    Clarissa De Antoni

    2009-06-01

    Full Text Available This paper investigates cohesion (emotional bonding and hierarchy (powerstructure in families with abuse against their children. Twenty low-incomefamilies participated. Father, mother and child’s perspective of family relations(cohesion and hierarchy were evaluated by the Family System Test(FAST. The relationship between father-child, mother-child, couple, andamong siblings were evaluated at typical and conflictive situations. Resultsshow a significance regarding to cohesion in typical and conflictive situationfor father-child and mother-child dyads in all perspectives (by father, mother,and child. There is no significant differences regarding to hierarchy. Theseresults suggest that the families see the intrafamilial violence as a constant,since they cannot differentiate between both situations.

  6. Alliance and group cohesion in relationship education.

    Science.gov (United States)

    Owen, Jesse; Antle, Becky; Barbee, Anita

    2013-09-01

    Relationship education programs have been shown as an effective way to increase relationship functioning. There is less known about how process factors, such as alliance with the leader or group dynamics, affect outcomes in these interventions. We examined group cohesion and alliance with the leader in a relationship education program tailored for individuals. Specifically, we examined whether participants' ratings (n = 126) of the group cohesion and alliance with the leader were associated with changes in relationship adjustment, relationship confidence, and communication quality from pre- to postintervention. The results demonstrated that participants' perceptions of the cohesion among the members in their relationship education group, but not the leader-participant alliance, made a significant contribution to the changes in participants' relationship functioning. These results suggest that the group dynamics among the members in the group are important ingredients in relationship education. Implications for relationship programs are provided. © FPI, Inc.

  7. PERSPECTIVES ON IMPROVING COHESION POLICY SPENDING

    Directory of Open Access Journals (Sweden)

    Andrei Sebastian Badea

    2011-03-01

    Full Text Available The aim of this paper is to reveal and summarize the latest visions and opinions published in articles and academic papers on the evaluation, institutional factors and the future of the European Cohesion Policy. The literature on the economic, territorial and social integration is vast and great emphasize has been put into the techniques, policies and instruments used in achieving these goals. The paper identifies some of the currents of opinion starting from cohesion evaluation methods and heading towards methods, techniques and policies for intervention without claiming to be an exhaustive endeavour. The article concludes with the summarising of the main opinions on the trends, directions and future of the European Cohesion Policy.

  8. Commercial Process of Bi-based 2212 Single Phase Superconducting Precursor Powder

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Laying emphasis on the preparation of Bi-based 2212 single phase superconducting powder, some technological parameters, which effect the single phase degree and uniformity of powder, such as prebaking, sintering and heat treatment were investigated and discussed. Ensuring the powder Tc at 83~85 K, the crucial impurity carbon was reduced to 0.03% and less. Adopting uncommon technique made the powder size to micrometer level, meanwhile the superconducting performance of the powder was unchanged. The fine superconducting powder was characterized. This process of Bi-based 2212 superconducting powder was successful.

  9. Whither Elite Cohesion in Mexico: A Comment

    Science.gov (United States)

    1988-11-01

    Generacicnes: Los Protagonistas de Ia Reforma y la Revoluci(n Mexicana, Secretaria de Educacion Pblica, Consejo Nacional de Fomento Educat ivo, Mexico City...t-, ~ ir;opy 000 WHITHER ELITE COHESION IN MEXICO : A COMMENT David Ronfeldt November 1988 DTIC ELECTEI Novo 6 la ... . ... ,D The RAND...Monica, CA 90406 21:8 WHITHER ELITE COHESION IN MEXICO : A COMMENT Pavii Ronfeldt Por dec:ies . .I(,xi -as had a ,henomena!!y cohr sive ruling e I ite non

  10. Interpretation of Wild 2 Dust Fine Structure: Comparison of Stardust Aluminium Foil Craters to the Three-Dimensional Shape of Experimental Impacts by Artificial Aggregate Particles and Meteorite Powders

    Energy Technology Data Exchange (ETDEWEB)

    Kearsley, A T; Burchell, M J; Price, M C; Graham, G A; Wozniakiewicz, P J; Cole, M J; Foster, N J; Teslich, N

    2009-12-10

    New experimental results show that Stardust crater morphology is consistent with interpretation of many larger Wild 2 dust grains being aggregates, albeit most of low porosity and therefore relatively high density. The majority of large Stardust grains (i.e. those carrying most of the cometary dust mass) probably had density of 2.4 g cm{sup -3} (similar to soda-lime glass used in earlier calibration experiments) or greater, and porosity of 25% or less, akin to consolidated carbonaceous chondrite meteorites, and much lower than the 80% suggested for fractal dust aggregates. Although better size calibration is required for interpretation of the very smallest impacting grains, we suggest that aggregates could have dense components dominated by {micro}m-scale and smaller sub-grains. If porosity of the Wild 2 nucleus is high, with similar bulk density to other comets, much of the pore-space may be at a scale of tens of micrometers, between coarser, denser grains. Successful demonstration of aggregate projectile impacts in the laboratory now opens the possibility of experiments to further constrain the conditions for creation of bulbous (Type C) tracks in aerogel, which we have observed in recent shots. We are also using mixed mineral aggregates to document differential survival of pristine composition and crystalline structure in diverse fine-grained components of aggregate cometary dust analogues, impacted onto both foil and aerogel under Stardust encounter conditions.

  11. 粉末冶金法制备超细晶AZ31镁合金及超塑性变形研究%Powder Metallurgy Prepared Ultra-fine Grain AZ31 Alloy and Its Superplastic Deformation

    Institute of Scientific and Technical Information of China (English)

    林莺莺; 胡杰仁

    2013-01-01

    采用粉末冶金法制备超细晶AZ31镁合金材料,并对其微观组织形貌及相成分进行研究;利用单向拉伸试验研究了该材料在不同条件下超塑性变形.结果表明,采用球磨、冷压制坯和热挤压法可获得晶粒尺寸在1微米以下的超细晶组织,该材料在250℃,1×10-3s-1的应变速率条件下获得了最大伸长率,基本达到超塑性状态.%Ultra-fine grain AZ31 alloy bars were fabricated by power metallurgy process,and the microstructure and phase composition were also researched.The superplastic deformation was studied by simple tension test.According to the results,AZ31 alloy with the grain size under 1 μm was prepared by the process of high energy ball milling,cold compacting and hot extrusion.The superplastic deformation was achieved under the temperature of 250 ℃ and strain rate of 1 × 10-3 s-1.

  12. The formation of open fractures in cohesive materials, results of scaled analogue and numerical modelling on fault zone porosity development

    Directory of Open Access Journals (Sweden)

    Urai J.L.

    2010-06-01

    Full Text Available We compare analogue and numerical models of dilatational fractures at low confining stress. These structures form an effective conduit for fluid flow in the field, but are difficult to model since they form in cohesive materials at low stresses. We use a truly cohesive powder for the analogue models and a Discrete Element Model (DEM with brittle-elastic bonds for the numerical modelling. We show that despite variations in the model type, small differences in the location of initial fractures and the way these structures link-up to control the evolution of the model, the observed structures are robust. Three structural zones develop where different fault types dominate. In 3D numerical models we show an increase of the porosity on the fault zone with increasing deformation. The progradation direction is shown to be controlled by the position of the fracture. The combination of analogue models with cohesive powder and DEMs with internal cohesion is an excellent tool to study the evolution of open fractures.

  13. Towards an integrated approach to cohesion and coherence in ...

    African Journals Online (AJOL)

    section discusses current theories of cohesion and coherence. .... that they are much more interested in developing cognitive strategies for .... directionality of research on cohesion and coherence in film translation but also pave the way.

  14. The Cohesion and Teaching of English Writing

    Institute of Scientific and Technical Information of China (English)

    刘洪明

    2008-01-01

    This paper introduces the purpose of our English teaching briefly and a few points for attention in the standards of English writing evaluation. On the basis of this, it discusses the relationship between English writing and cohesion in order to try to find an appropriate method for our English writing.

  15. Discourse Cohesion in Sign and Speech.

    Science.gov (United States)

    Morgan, Gary

    2000-01-01

    Describes the development of discourse cohesion in bilingual children through an analysis of narrative discourses produced by hearing children of deaf parents (HCDP) in both British Sign Language (BSL) and spoken English. Reference mechanisms in both languages are described in the context of recent work on narrative and discourse organization…

  16. Cohesion in Interlanguage: A Study of Conjunction.

    Science.gov (United States)

    Beebe, Leslie M.

    A study of textual cohesion in the oral discourse of learners of English as a second language had as subjects 19 Asians from 4 language backgrounds, who were living and, in most cases, studying English in the United States. Analysis of taped conversations focused on the use of conjunctive adjuncts of three kinds: (1) simple adverbs (e.g., and,…

  17. Textual Cohesion and Second-Language Comprehension.

    Science.gov (United States)

    Jonz, Jon

    1987-01-01

    Analysis of responses to two cloze tests administered to native and non-native speakers of English revealed that non-natives were far less capable of coping with the loss of redundant cohesive data than were natives. Nonnatives were more reliant on text in comprehension process than were native speakers. (Author/CB)

  18. Engineering molecular crystals with abnormally weak cohesion.

    Science.gov (United States)

    Maly, Kenneth E; Gagnon, Eric; Wuest, James D

    2011-05-14

    Adding astutely placed methyl groups to hexaphenylbenzene increases molecular weight but simultaneously weakens key C-H···π interactions, thereby leading to decreased enthalpies of sublimation and showing that materials with abnormally weak cohesion can be made by identifying and then obstructing interactions that help control association.

  19. Group Cohesion in Experiential Growth Groups

    Science.gov (United States)

    Steen, Sam; Vasserman-Stokes, Elaina; Vannatta, Rachel

    2014-01-01

    This article explores the effect of web-based journaling on changes in group cohesion within experiential growth groups. Master's students were divided into 2 groups. Both used a web-based platform to journal after each session; however, only 1 of the groups was able to read each other's journals. Quantitative data collected before and…

  20. The Corporate Stake in Social Cohesion

    Science.gov (United States)

    Oketch, Moses O.

    2005-01-01

    Corporate Social Responsibility (CSR) is a function that transcends, but includes, making profits, creating jobs, and producing goods and services. The effectiveness with which corporations perform this function determines their contribution (or lack of contribution) to social cohesion. This article therefore presents a discussion of some of the…

  1. On Coherence and Cohesion in Discourse Analysis

    Institute of Scientific and Technical Information of China (English)

    李振国

    2013-01-01

    ‘cohesion’is the way words formally hang together in sentences and the like, and“coherence”captures the content-based connections between the words that make them produce sense. In the discourse, while the local sequence of turns creates a certain amount of cohesion, it isn’t sufficient to guarantee coherence.

  2. Investigating Team Cohesion in COCOMO II.2000

    Science.gov (United States)

    Snowdeal-Carden, Betty A.

    2013-01-01

    Software engineering is team oriented and intensely complex, relying on human collaboration and creativity more than any other engineering discipline. Poor software estimation is a problem that within the United States costs over a billion dollars per year. Effective measurement of team cohesion is foundationally important to gain accurate…

  3. Role of Education in Building Social Cohesion

    Science.gov (United States)

    Khan, Zebun Nisa

    2016-01-01

    Social Cohesion is the expression of that tradition of tolerance in all religions and cultures that are the basis of peace and progress. It is foreign to know culture and native to all nations. Tolerance and mercy have always and in all cultures being ideals of Government rules and human behavior. Professional educator often comments on the poor…

  4. Validation of the Child Sport Cohesion Questionnaire

    Science.gov (United States)

    Martin, Luc J.; Carron, Albert V.; Eys, Mark A.; Loughead, Todd

    2013-01-01

    The purpose of the present study was to test the validity evidence of the Child Sport Cohesion Questionnaire (CSCQ). To accomplish this task, convergent, discriminant, and known-group difference validity were examined, along with factorial validity via confirmatory factor analysis (CFA). Child athletes (N = 290, M[subscript age] = 10.73 plus or…

  5. Investigating Team Cohesion in COCOMO II.2000

    Science.gov (United States)

    Snowdeal-Carden, Betty A.

    2013-01-01

    Software engineering is team oriented and intensely complex, relying on human collaboration and creativity more than any other engineering discipline. Poor software estimation is a problem that within the United States costs over a billion dollars per year. Effective measurement of team cohesion is foundationally important to gain accurate…

  6. Validation of the Child Sport Cohesion Questionnaire

    Science.gov (United States)

    Martin, Luc J.; Carron, Albert V.; Eys, Mark A.; Loughead, Todd

    2013-01-01

    The purpose of the present study was to test the validity evidence of the Child Sport Cohesion Questionnaire (CSCQ). To accomplish this task, convergent, discriminant, and known-group difference validity were examined, along with factorial validity via confirmatory factor analysis (CFA). Child athletes (N = 290, M[subscript age] = 10.73 plus or…

  7. Microzonation Analysis of Cohesionless and Cohesive Soil

    Directory of Open Access Journals (Sweden)

    Tan Choy Soon

    2017-01-01

    Full Text Available Urban seismic risk is a continuous worldwide issue, numerous researchers are putting great effort in dealing with how to minimise the level of the threat. The only way to minimise the social and economic consequences caused but the seismic risk is through comprehensive earthquake scenario analysis such as ground response analysis. This paper intends to examine the characteristic of shear wave velocity and peak ground acceleration on cohesionless and cohesiveness soil. In order to examine the characteristic of shear wave velocity and peak ground acceleration on cohesionless and cohesiveness soil, ground response analysis was performed using Nonlinear Earthquake Site Response Analysis (NERA and Equivalent-linear Earthquake Site Response Analysis (EERA. The value of ground acceleration was initially high at bedrock and vanishes during the propagation process. It is thus, the measured acceleration at surface is therefore much lower as compare to at bedrock. Result shows that seismic waves can travel faster in harder soil as compared to softer soil. Cohesive soil contributes more to the shaking amplification than cohesionless soil such as sand and harder soil. This is known as local site effect. The typical example is the Mexico Earthquake that happened in 1985. As conclusion, peak ground acceleration for cohesive soil is higher than in cohesionless soil.

  8. Ultrasound treatment of centrifugally atomized 316 stainless steel powders

    Science.gov (United States)

    Rawers, James C.; McCune, Robert A.; Dunning, John S.

    1991-12-01

    The Bureau of Mines is studying the surface characteristics of rapidly solidified powders and the potential for surface modification of fine powders prior to consolidation. The surface modification and work hardening of fine powders were accomplished by applying high-energy ultrasound to centrifugally atomized austenitic 316 stainless steel powders suspended in liquid media. Cavitation implosion changed the surface morphology, hammering the surface and occasionally fretting off microchips of work-hardened metal. Ultrasound-cavitation work-hardened metal powder surfaces producing a strained, duplex austenite face-centered cubic (fcc)-martensite body-centered tetragonal (bct) phase structure. The amount of work hardening depended upon the quantity of ultrasound energy used, considering both power level and experimental time. Work hardening was relatively independent of the liquid media used.

  9. On the Relationships between the Cohesive Devices and Their Meanings

    Institute of Scientific and Technical Information of China (English)

    肖肇威

    2008-01-01

    Cohesion is one of the phenomena of the text. It is expressed through the cohesive devices.As part of Functional Grammar,the cohesive devices relate themselves naturally to the meanings,which exist both in the text and in its social context.This paper is to explore the relationship between the cohesive devices and their meanings.These meanings subsume the discourse semantics in the text and the register in the social context.

  10. Computer Models Simulate Fine Particle Dispersion

    Science.gov (United States)

    2010-01-01

    Through a NASA Seed Fund partnership with DEM Solutions Inc., of Lebanon, New Hampshire, scientists at Kennedy Space Center refined existing software to study the electrostatic phenomena of granular and bulk materials as they apply to planetary surfaces. The software, EDEM, allows users to import particles and obtain accurate representations of their shapes for modeling purposes, such as simulating bulk solids behavior, and was enhanced to be able to more accurately model fine, abrasive, cohesive particles. These new EDEM capabilities can be applied in many industries unrelated to space exploration and have been adopted by several prominent U.S. companies, including John Deere, Pfizer, and Procter & Gamble.

  11. Cohesiveness and Performance on an Additive Task: Evidence for Multidimensionality.

    Science.gov (United States)

    Zaccaro, Stephen J.; Lowe, Charles A.

    1988-01-01

    Presents a study designed to contrast the effects of task-based and interpersonal cohesiveness on group performance of students. Concludes that high task cohesion helped group performance, while interpersonal attraction had no apparent effect. Finding that increased interpersonal cohesion improved task commitment, the authors suggest that…

  12. Path dependence of truss-like mixed mode cohesive laws

    DEFF Research Database (Denmark)

    Goutianos, Stergios; Sørensen, Bent F.

    2012-01-01

    A general theoretical analysis is presented to prove that, under mixed mode fracture, truss-like mixed mode cohesive laws (cohesive laws that are coupled in a special manner such that the traction vector follows the separation/opening vector) are path independent only in the limited case where th...... and numerically that these cohesive laws are path dependent....

  13. Territorial cohesion post - 2013: to whomsoever it may concern

    NARCIS (Netherlands)

    Faludi, A.K.F.

    2010-01-01

    Conceived as a motion for resolution, the paper considers territorial cohesion now being on the statute book, the Green Paper on Territorial Cohesion, Barca making the case for integrated, place-based strategies, the EU Strategy for the Baltic Sea Region and the future of Cohesion policy. The recom

  14. Facilitating Group Cohesion among Adolescents through Challenge Course Experiences.

    Science.gov (United States)

    Glass, J. Scott; Benshoff, James M.

    2002-01-01

    A study examined the effects of participation in a low-element challenge course on younger adolescents' perceptions of group cohesion. Pre- and post-tests of group cohesion were administered to 167 North Carolina adolescents aged 11-14. Participants perceived an increase in group cohesion after the daylong program, regardless of their age, race,…

  15. Intact Discourse Cohesion and Coherence Following Bilateral Ventromedial Prefrontal Cortex

    Science.gov (United States)

    Kurczek, Jake; Duff, Melissa C.

    2012-01-01

    Discourse cohesion and coherence give communication its continuity providing the grammatical and lexical links that hold an utterance or text together and give it meaning. Researchers often link cohesion and coherence deficits to the frontal lobes by drawing attention to frontal lobe dysfunction in populations where discourse cohesion and…

  16. Cohesion in Compositions of Turkish and Immigrant Students

    Science.gov (United States)

    Coskun, Eyyup

    2011-01-01

    Cohesion refers to the relationships established between sentences and paragraphs via the units in the surface structure of the text. This study evaluated texts written by Uzbek origin immigrant students and Turkish students living in Hatay in terms of the use of cohesion devices (ellipsis, conjunctions, lexical cohesion, reference, substitution).…

  17. Is social cohesion one latent concept? Investigating the dimensionality of social cohesion using Kearns and Forrest Typology

    OpenAIRE

    Reeskens, Tim; Botterman, Sarah; Hooghe, Marc

    2008-01-01

    One of the most abundantly used concepts in contemporary social sciences and among policy experts is 'social cohesion'. However, it is difficult to grasp how social cohesion is defined or measured. In this paper, we follow the line of reasoning of urban sociologists Kearns and Forrest (2000), who ascribed five dimensions to social cohesion. Although frequently used in theoretical discussions, methodological rigorous tests on the dimensionality of these five social cohesion dimensions are abse...

  18. Dry powder segregation and flowability: Experimental and numerical studies

    Science.gov (United States)

    Ely, David R.

    Dry powder blending is a very important industrial and physical process used in the production of numerous pharmaceutical dosage forms such as tablets, capsules, and dry powder aerosols. Key aspects of this unit operation are process monitoring and control. Process control is particularly difficult due to the complexity of particle-particle interactions, which arise from the adhesion/cohesion characteristics of interfaces and morphological characteristics such as particle size, shape, and dispersity. The effects of such characteristics need to be understood in detail in order to correlate individual particle properties to bulk powder properties. The present dissertation numerically and experimentally quantifies the mixing process to rationalize particle-particle interactions. In particular, near infrared spectroscopy (NIRS) was used to non-invasively characterize in real-time the blending processes and thus investigate the dynamics of blending under different operating conditions. A novel image analysis technique was developed to quantify the scale of segregation from images obtained non-destructively via near infrared chemical imaging (NIR-CI). Although NIR-CI data acquisition times are too long for real-time data collection, NIR-CI has an advantage, in that it provides the spatial distribution of the drug. Therefore, NIRS and NIR-CI are complementary techniques for investigating the complex process of blending dry powders and assessing end-product quality. Additionally, the discrete element method was used to investigate the effect of powder cohesion on the packing fraction. Simulations indicated an exponential relationship between the random loose packing fraction and cohesive forces. Specifically, the packing fraction decreased asymptotically with increased ratio of cohesive force to particle weight. Thus, increasing this force ratio above a critical value has negligible impact on the packing fraction. Such result directly impacts the Hausner ratio flowability

  19. Micro-feeding and dosing of powders via a small-scale powder pump.

    Science.gov (United States)

    Besenhard, M O; Fathollahi, S; Siegmann, E; Slama, E; Faulhammer, E; Khinast, J G

    2017-03-15

    Robust and accurate powder micro-feeding (micro-dosing (micro-feeders that yield feed rates below 5mg/s use gravimetric feeding principles, feed rates depend primarily on powder properties. In contrast, volumetric powder feeders do not require regular calibration because their feed rates are primarily determined by the feeder's characteristic volume replacement. In this paper, we present a volumetric micro-feeder based on a cylinder piston system (i.e., a powder pump), which allows accurate micro-feeding and feed rates of a few grams per hours even for very fine powders. Our experimental studies addressed the influence of cylinder geometries, the initial conditions of bulk powder, and the piston speeds. Additional computational studies via Discrete Element Method simulations offered a better understanding of the feeding process, its possible limitations and ways to overcome them. The powder pump is a simple yet valuable tool for accurate powder feeding at feed rates of several orders of magnitude. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. The Effect of Alumina Dispersant Powder on the Workability of Chromia Based Refractory for IGCC Application

    Science.gov (United States)

    Ming, Zhao Jing; Xun, Yang Zheng; Hong, Hwang Kyu; Hwan, Park Sang

    2011-10-01

    The quality of refractory applied on IGCC is a key factor that affects the cost of production. The workability and microstructure of chromia based castable are varied by introducing different type of alumina dispersant powder, such as active alumina powder. In this study, three types of active alumina powder are added to improve the workability. It's proved that the specific surface area and particle size distribution of fine powders in matrix part greatly affect the flow values and microstructures.

  1. Characterization of powdered fish heads for bone graft biomaterial applications.

    Science.gov (United States)

    Oteyaka, Mustafa Ozgür; Unal, Hasan Hüseyin; Bilici, Namık; Taşçı, Eda

    2013-01-01

    The aim of this study was to define the chemical composition, morphology and crystallography of powdered fish heads of the species Argyrosomus regius for bone graft biomaterial applications. Two sizes of powder were prepared by different grinding methods; Powder A (coarse, d50=68.5 µm) and Powder B (fine, d50=19.1 µm). Samples were analyzed using X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscopy (SEM), thermogravimetry (TG), and energy dispersive X-ray spectroscopy (EDS). The powder was mainly composed of aragonite (CaCO3) and calcite (CaCO3). The XRD pattern of Powder A and B matched standard aragonite and calcite patterns. In addition, the calcium oxide (CaO) phase was found after the calcination of Powder A. Thermogravimetry analysis confirmed total mass losses of 43.6% and 47.3% in Powders A and B, respectively. The microstructure of Powder A was mainly composed of different sizes and tubular shape, whereas Powder B showed agglomerated particles. The high quantity of CaO and other oxides resemble the chemical composition of bone. In general, the powder can be considered as bone graft after transformation to hydroxyapatite phase.

  2. Relating Cohesive Zone Model to Linear Elastic Fracture Mechanics

    Science.gov (United States)

    Wang, John T.

    2010-01-01

    The conditions required for a cohesive zone model (CZM) to predict a failure load of a cracked structure similar to that obtained by a linear elastic fracture mechanics (LEFM) analysis are investigated in this paper. This study clarifies why many different phenomenological cohesive laws can produce similar fracture predictions. Analytical results for five cohesive zone models are obtained, using five different cohesive laws that have the same cohesive work rate (CWR-area under the traction-separation curve) but different maximum tractions. The effect of the maximum traction on the predicted cohesive zone length and the remote applied load at fracture is presented. Similar to the small scale yielding condition for an LEFM analysis to be valid. the cohesive zone length also needs to be much smaller than the crack length. This is a necessary condition for a CZM to obtain a fracture prediction equivalent to an LEFM result.

  3. Cohesion and Metaphor Aspects in Andabhuana Text

    Directory of Open Access Journals (Sweden)

    Ida Bagus Mahardika

    2015-02-01

    Full Text Available Cohesion and metaphor are the unique and interesting parts of language aspects in Andhabhuan text to research. They are quite dominant aspects in the story in developing its literature aesthetic. This research is based on the arts technical and analytical method. The result of the research on those two aspects shows that traditional aesthetic style in arts, as described in Andabhuana verses emphasize on the reference, meaning, selection and variation of words. The language parts used are aimed at bringing the text ideology to humanity perspective, especially the ?iwatattwa values as parts of Hindu teaching. Hence the cohesion and metaphor in Andabhuana text  are  semiotic description to transform to Balinese Hindus as most of them follow ?iwatattwa belief.

  4. AUTOMATIC TEXT SUMMARIZATION BASED ON TEXTUAL COHESION

    Institute of Scientific and Technical Information of China (English)

    Chen Yanmin; Liu Bingquan; Wang Xiaolong

    2007-01-01

    This paper presents two different algorithms that derive the cohesion structure in the form of lexical chains from two kinds of language resources HowNet and TongYiCiCiLin.The research that connects the cohesion structure of a text to the derivation of its summary is displayed.A novel model of automatic text summarization is devised,based on the data provided by lexicai chains from original texts.Moreover,the construction rules of lexical chains are modified according to characteristics of the knowledge database in order to be more suitable for Chinese suIninarization.Evaluation results show that high quality indicative summaries are produced from Chinese texts.

  5. Measurement of Cohesion in Asteroid Regolith Materials

    Science.gov (United States)

    Kleinhenz, Julie E.; Gaier, James R.; Waters, Deborah L.; Harvey, Ralph; Zeszut, Zoe; Carreno, Brandon; Shober, Patrick

    2017-01-01

    A study has been initiated to examine cohesive forces in asteroid materials to contribute to a better understanding of low density bodies such as asteroids and Phobos, and assist in exploration missions involving interaction with their surface material. The test specimen used in this study was a lightly weathered CM2 meteorite which is spectroscopically similar to Type C (carbonaceous) asteroids, and thought to have representative surface chemistry. To account for sample heterogeneity, adhesion forces were measured between the CM2 sample and its five primary mineral phase components. These adhesive forces bound the range of cohesive force that can be expected for the bulk material. All materials were characterized using a variety of optical and spectroscopic methods. Adhesive forces on the order of 50 to 400 µN were measured using a torsion balance in an ultrahigh vacuum chamber. The mineral samples exhibited clearly different adhesive strengths in the following hierarchy: Serpentine > Siderite > Bronzite > Olivine ˜ Fe-Ni.

  6. Aluminum powder metallurgy processing

    Energy Technology Data Exchange (ETDEWEB)

    Flumerfelt, J.F.

    1999-02-12

    The objective of this dissertation is to explore the hypothesis that there is a strong linkage between gas atomization processing conditions, as-atomized aluminum powder characteristics, and the consolidation methodology required to make components from aluminum powder. The hypothesis was tested with pure aluminum powders produced by commercial air atomization, commercial inert gas atomization, and gas atomization reaction synthesis (GARS). A comparison of the GARS aluminum powders with the commercial aluminum powders showed the former to exhibit superior powder characteristics. The powders were compared in terms of size and shape, bulk chemistry, surface oxide chemistry and structure, and oxide film thickness. Minimum explosive concentration measurements assessed the dependence of explosibility hazard on surface area, oxide film thickness, and gas atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization oxidation of aluminum powder. An Al-Ti-Y GARS alloy exposed in ambient air at different temperatures revealed the effect of reactive alloy elements on post-atomization powder oxidation. The pure aluminum powders were consolidated by two different routes, a conventional consolidation process for fabricating aerospace components with aluminum powder and a proposed alternative. The consolidation procedures were compared by evaluating the consolidated microstructures and the corresponding mechanical properties. A low temperature solid state sintering experiment demonstrated that tap densified GARS aluminum powders can form sintering necks between contacting powder particles, unlike the total resistance to sintering of commercial air atomization aluminum powder.

  7. Particle Morphology Effects on Flow Characteristics of PS304 Plasma Spray Coating Feedstock Powder Blend

    Science.gov (United States)

    Stanford, Malcolm K.; DellaCorte, Christopher; Eylon, Daniel

    2002-01-01

    The effects of BaF2-CaF 2 particle morphology on PS304 feedstock powder flow ability have been investigated. BaF2-CaF2 eutectic powders were fabricated by comminution (angular) and by gas atomization (spherical). The fluoride powders were added incrementally to the other powder constituents of the PS304 feedstock: nichrome, chromia, and silver powders. A linear relationship between flow time and concentration of BaF2-CaF2 powder was found. Flow of the powder blend with spherical BaF2-CaF2 was better than the angular BaF2-CaF2. Flow ability of the powder blend with angular fluorides decreased linearly with increasing fluoride concentration. Flow of the powder blend with spherical fluorides was independent of fluoride concentration. Results suggest that for this material blend, particle morphology plays a significant role in powder blend flow behavior, offering potential methods to improve powder flow ability and enhance the commercial potential. These findings may have applicability to other difficult-to-flow powders such as cohesive ceramics.

  8. Enhancing Unit Cohesion Via Social Media

    Science.gov (United States)

    2016-06-10

    and a social network that individuals rely on for advice, help, and even references for future work and education .4 Prior to the social media boom...door for further research in the field . The nascent elements from this analysis of unit cohesion via social media indicate the following key points...upon the knowledge base within the civilian education system. Similarly, vertical bonding may occur via social media ; however, it is often very

  9. Brownfield regeneration: Towards strengthening social cohesion?

    Directory of Open Access Journals (Sweden)

    Minić Marta

    2016-01-01

    Full Text Available In broader terms, the paper refers to the topic of brownfield regeneration, as one of the most complex mechanisms for sustainable spatial development. In addition to the fact that brownfield regeneration demands a variety of instruments, such as: tax subsidies, the change of land use ownership, soil remediation, planning regulative amendments, etc., the complexity of brownfield regeneration is primarily seen in a number of stakeholders participating in such a process. Thus, the paper focuses on the social aspect of brownfield regeneration - precisely, on researching the community role and reviewing the possibilities for achieving the 'local' interests in complex developmental processes. The main research hypothesis is that brownfield regeneration positively affects the creation of and strengthening the social cohesion in the areas close to the brownfield site. More precisley, the paper presents the ways towards strenghtening social cohesion in the initial phase of the brownfield regeneration process, as well as the effects of such a process in its operationalisation phase on social cohesion. The thesis is examined by two main parameters: 1 participation of local community, and 2 social costs and benefits of brownfield regeneration versus greenfield investment. The research results are presented in the form of argumentative essay. In fact, the critical overview of arguments for and against the main research hypothesis is provided based on the review of interdisciplinary literature in the domain of brownfield regeneration. Such research organisation ensures the identification and description of the measures needed for strengthening social cohesion, as an utmost goal of this research. The final research contribution is about offering the guidelines for similar methodological approach in urban research.

  10. Force transmission in cohesive granular media

    Science.gov (United States)

    Radjai, Farhang; Topin, Vincent; Richefeu, Vincent; Voivret, Charles; Delenne, Jean-Yves; Azéma, Emilien; El Youssoufi, Said

    2010-05-01

    We use numerical simulations to investigate force and stress transmission in cohesive granular media covering a wide class of materials encountered in nature and industrial processing. The cohesion results either from capillary bridges between particles or from the presence of a solid binding matrix filling fully or partially the interstitial space. The liquid bonding is treated by implementing a capillary force law within a debonding distance between particles and simulated by the discrete element method. The solid binding matrix is treated by means of the Lattice Element Method (LEM) based on a lattice-type discretization of the particles and matrix. Our data indicate that the exponential fall-off of strong compressive forces is a generic feature of both cohesive and noncohesive granular media both for liquid and solid bonding. The tensile forces exhibit a similar decreasing exponential distribution, suggesting that this form basically reflects granular disorder. This is consistent with the finding that not only the contact forces but also the stress components in the bulk of the particles and matrix, accessible from LEM simulations in the case of solid bonding, show an exponential fall-off. We also find that the distribution of weak compressive forces is sensitive to packing anisotropy, particle shape and particle size distribution. In the case of wet packings, we analyze the self-equilibrated forces induced by liquid bonds and show that the positive and negative particle pressures form a bi-percolating structure.

  11. Overtopping breaching of cohesive homogeneous earth dam with different cohesive strength

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    In consideration of the range of clay content of Chinese earth dams, the world’s highest prototype tests have been made to research on the effects of cohesive strength of filling of cohesive homogeneous earth dam on breach formation. Three breach mechanisms were presented, they were the source-tracing erosion of dam body with the form of "multilevel headcut", "two-helix flow" erosion of dam crest and collapse of breach sidewalls due to instability. It can be concluded that the cohesive strength of filling of earth dam has great effect on breach formation. When the cohesive strength is bigger, the breach process becomes slower, and the peak outflow and the final width and depth of breach become smaller. The main character of the breach formation is head cutting and dumping collapse. When the cohesive strength is smaller, the breach process becomes faster, and the peak outflow, the final width and depth of breach become bigger. The main character of the breach formation is single level head cutting and shearing collapse.

  12. FY 2000 Report on the results of international cooperative research scheme (power generation - No.3). Developmental research on high-performance plasma-assisted fine coal powder combustion mechanism for coal-fired power generation boilers to realize oilless ignition; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo seika hokokusho (hatsuden No.3). Oilless chakka wo jitsugensuru sekitan karyoku hatsuden bifuntan nenshoroyo koseino plasma jonen kiko no kaihatsu kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the results of the developmental research on the high-performance plasma-assisted fine coal powder combustion mechanism for coal-fired power generation boilers, a theme adopted by the international cooperative research scheme. The program for design/manufacture of the plasma torch manufactures laminar type torches for 100kW high power class and 10kW middle class. The high-performance plasma-assisted combustion mechanism is designed and manufactured using the torch. It has a structure which supplies secondary air and secondary coal flow to the primary coal flow. It is tested for starting up a commercial boiler firing finely pulverized coal, to confirm its functions. The tests for optimizing the oilless ignition and operation are conducted in Tashtagonal Iron Plant and Berdsk Chemical Plant. It is found that the cold start can be realized in the boiler, when the muffle burners are preheated for 30 to 40 minutes before the finely pulverized coal is supplied and the steady-state coal combustion is attained 3 to 5 minutes after the coal is supplied. The program for the combustion basics for the plasma-assisted mechanism collects the data related to its dependence on coal type. (NEDO)

  13. Industrial mineral powder production in China

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The recent annual output of major industrial mineral powders in the mainland of China has been more than 100 million t, accompanied by active development of such supporting technology as comminution, classification, separation/purification, and surface modification. In particular, the present paper reviews technologies for preparing ultra-fine particles involving dry and wet processing, modification and composition, calcination of kaolin clay, and processing of spherical/acerous industrial minerals.

  14. Cooked sausage batter cohesiveness as affected by sarcoplasmic proteins.

    Science.gov (United States)

    Farouk, M M; Wieliczko, K; Lim, R; Turnwald, S; Macdonald, G A

    2002-05-01

    In the first trial, m. semitendinosus and m. biceps femoris were held at 0, 10 and 35 °C until they entered rigor, and in the second trial, minced m. semitendinosus was washed in water for 15, 30, 45 or 60 min. The samples from both the trials were then used to make a finely comminuted sausage batter. Soluble sarcoplasmic protein (SSP) levels decreased with increasing rigor temperature (P < 0.05) or washing (P < 0.01). Cooked batter shear stress was not affected by SSP level, but batter shear strain decreased with the decreasing SSP level associated with an increasing rigor temperature (P < 0.05) or washing (P < 0.01). Reducing the SSP content lowered the cook yield (P < 0.05) and emulsion stability (P < 0.01) of the batter from the washed samples compared to that of controls. The results suggest that sarcoplasmic proteins are important in determining the strain values (cohesiveness) of cooked sausage batter.

  15. Analysis of Minor Component Segregation in Ternary Powder Mixtures

    Science.gov (United States)

    Asachi, Maryam; Hassanpour, Ali; Ghadiri, Mojtaba; Bayly, Andrew

    2017-06-01

    In many powder handling operations, inhomogeneity in powder mixtures caused by segregation could have significant adverse impact on the quality as well as economics of the production. Segregation of a minor component of a highly active substance could have serious deleterious effects, an example is the segregation of enzyme granules in detergent powders. In this study, the effects of particle properties and bulk cohesion on the segregation tendency of minor component are analysed. The minor component is made sticky while not adversely affecting the flowability of samples. The segregation extent is evaluated using image processing of the photographic records taken from the front face of the heap after the pouring process. The optimum average sieve cut size of components for which segregation could be reduced is reported. It is also shown that the extent of segregation is significantly reduced by applying a thin layer of liquid to the surfaces of minor component, promoting an ordered mixture.

  16. Analysis of Minor Component Segregation in Ternary Powder Mixtures

    Directory of Open Access Journals (Sweden)

    Asachi Maryam

    2017-01-01

    Full Text Available In many powder handling operations, inhomogeneity in powder mixtures caused by segregation could have significant adverse impact on the quality as well as economics of the production. Segregation of a minor component of a highly active substance could have serious deleterious effects, an example is the segregation of enzyme granules in detergent powders. In this study, the effects of particle properties and bulk cohesion on the segregation tendency of minor component are analysed. The minor component is made sticky while not adversely affecting the flowability of samples. The segregation extent is evaluated using image processing of the photographic records taken from the front face of the heap after the pouring process. The optimum average sieve cut size of components for which segregation could be reduced is reported. It is also shown that the extent of segregation is significantly reduced by applying a thin layer of liquid to the surfaces of minor component, promoting an ordered mixture.

  17. A Novel Method for Direct Synthesis of WC-Co Nanocomposite Powder

    Science.gov (United States)

    Zhu, M.; Bao, X. Y.; Yang, X. P.; Gu, N. S.; Wang, H.; Zeng, M. Q.; Dai, L. Y.

    2011-09-01

    In this study, a novel method, termed dielectric-barrier-discharge-plasma (DBDP) assisted ball milling and low-temperature carburization, was used to synthesize WC-Co nanocomposite powder. X-ray diffraction, scanning/transmission electron microscopy, and differential scanning calorimetry were used to characterize the microstructure of powders. Starting from W, Co, and graphite powder mixtures, the DBDP-milled W-C-10Co powder exhibited a flakelike morphology with very fine lamellar structure. The WC-Co composite powder was synthesized at 1273 K (1000 °C), which is much lower than the requisite temperature for the conventional carburizing method. The obtained WC-Co composite powder had a nanocomposite microstructure in which fine WC particles were bounded by homogenously distributed Co phase, and the WC crystals had a slablike morphology with a planar size of about 200 nm and carburization temperature and the nanocomposite structure of WC-Co powder.

  18. Characteristics of work groups and their relationship with social and task cohesion in student teams.

    Science.gov (United States)

    Forrester, William R; Tashchian, Armen

    2004-08-01

    Results of an exploratory study of relationships between work-group characteristics and the social and task cohesion of 18 business students engaged in team class projects. Regression analysis of scores on workload sharing, team spirit, task flexibility, and team cohesiveness for scales of the Work Group Characteristics Inventory indicated sharing of the workload was significantly associated with both task and social cohesion; team spirit with task cohesion but not social cohesion; and task flexibility with social cohesion but not task cohesion.

  19. Coaches' Perceptions of Team Cohesion in Paralympic Sports.

    Science.gov (United States)

    Falcão, William R; Bloom, Gordon A; Loughead, Todd M

    2015-07-01

    The purpose of this study was to investigate Paralympic coaches' perceptions of team cohesion. Seven head coaches of summer and winter Canadian Paralympic sport teams participated in the study. Four participants coached individual sports and 3 coached team sports. Data were collected using semistructured interviews and analyzed using thematic analysis. The results addressed the coaches' perceptions of cohesion in the Paralympic sport setting and strategies used to foster cohesion with their teams. Participants described using techniques and strategies for enhancing cohesion that were similar to those in nondisability sport, such as task-related activities, goal setting, and regularly communicating with their athletes. They also listed how cohesion was distinct to the Paralympic setting, such as the importance of interpersonal activities to build social cohesion. The implications of these results for coaching athletes with a disability are also presented.

  20. CONSIDERATIONS REGARDING THE TEAM COHESION IMPACT ON HANDBALL PERFORMANCE

    Directory of Open Access Journals (Sweden)

    TONIŢA FLORENTINA

    2012-06-01

    Full Text Available AbstractIntroduction. From the perspective of our paper, we consider that creating an optimum cohesion in the handball team can have favorable influences on performances.Purpose. The present study describes the theoretical premises related to the concept of “cohesion” within the handball team.Content. The cohesion influence on the group productivity has been intensely studied. High cohesion groups can easily establish performance standards and offer a wider range of awards to its members. M.E. Shaw (1981 discovered that highly cohesive groups are cooperative, friendly and they use a democratic form for the behavior control. In low cohesion groups, members are hostile and aggressive, they are pleased when their colleagues make mistakes and they adopt a decision-making autocratic style.Conclusions. Relationships among teammates are decisive to ensure the group cohesion and the efficiency of a team activity depends on the quality of these relationships.

  1. ELECTROSTATICALLY SUPPORTED MIXING OF FINE GRAINED PARTICLES

    Institute of Scientific and Technical Information of China (English)

    K.-E.; Wirth; M.; Linsenbühler

    2005-01-01

    The processing of fine-grained particles with diameters between 1 and 10 microns is difficult due to strong van-der-Waals attraction forces. In order to improve the handling properties, the fine-grained particles, i.e. host-particles,are coated with various nanoparticles, i.e. guest-particles. The mixing of fine-grained powders is influenced by particle-particle interactions. If these forces are distinctively used, both interactive and ordered mixtures can be produced.These particle mixtures consist of composite-particles that have new physical properties. These modified properties d epend strongly on the coating process, the diameter- and mass-relationship of the guest- and the host-particles. The properties of the composite-particles can systematically be adjusted to the requirements of industrial applications. For example, a laboratory bubbling fluidized bed can be used to describe the conveying behavior of the functionalized host-particles. Applications for the functionalized particles are in the pharmaceutical and the powder coating industries,e.g. enhanced dry powder inhalers and thin lacquer films. The present research compares three different mixing/coating processes. The composite-particles are characterized by TEM, SEM and with their fluidization characteristics. The coating process itself is monitored by the electrostatic charge of the particles.

  2. Cohesion Based Personalized Community Recommendation System

    Directory of Open Access Journals (Sweden)

    Md Mamunur Rashid

    2016-08-01

    Full Text Available Our life is totally engaged by the progressive growth of online social networking. Because, millions of users are interconnecting with each other using different social media sites like Facebook, Twitter, LinkedIn, Google+, Pinterest, Instagram etc. Most of the social sites like Facebook, Google+ allow users to join different groups or communities where people can share their common interests and express opinions around a common cause, problem or activity. However, an information overloading issue has disturbed users as thousands of communities or groups are creating each day. To resolve this problem, we have presented a community or group recommendation system centered on cohesion where cohesion represents high degree of connectedness among users in social network. In this paper, we emphasis on suggesting useful communities (or groups in term of Facebook that users personally attracted in to join; reducing the effort to find useful information based on cohesion. Our projected framework contains of the steps like: extracting sub-network from a social networking site (SNS, computing the impact of amity(both real-life or social and SNS connected, measuring user proclivity factor, calculating threshold from existing communities or groups of a user and lastly recommending community or group based on derived threshold. In result analysis part, we consider the precision-recall values by discarding community or group one at a time from the list of communities or groups of a certain user and checking whether the removed community or group is recommended by our proposed system. We have evaluated our system with 20 users and found 76% F1 accuracy measure.

  3. Determinants of group cohesion on the football team.

    Directory of Open Access Journals (Sweden)

    Sheriff Sarhan

    2011-10-01

    Full Text Available It is shown analysis of the determinants of cohesion and their manifestation in athletes - football players. We consider personal factors and their relationship to credible group cohesion among players. Established that the determinants of group cohesion are a factor with "emotional instability - emotional stability," the experience of the team, normative behavior (factor G, the factor Q2: «conformism - non-conformism," resistance to conflict, factor A "closed - sociability" and the factor F: «restraint - expressiveness."

  4. CONSIDERATIONS REGARDING THE TEAM COHESION IMPACT ON HANDBALL PERFORMANCE

    OpenAIRE

    TONIŢA FLORENTINA; POPESCU LAVINIA; ALEXANDRESCU NICOLETA; MACOVEI SABINA

    2012-01-01

    AbstractIntroduction. From the perspective of our paper, we consider that creating an optimum cohesion in the handball team can have favorable influences on performances.Purpose. The present study describes the theoretical premises related to the concept of “cohesion” within the handball team.Content. The cohesion influence on the group productivity has been intensely studied. High cohesion groups can easily establish performance standards and offer a wider range of awards to its members. M.E...

  5. Nano powders, components and coatings by plasma technique

    Science.gov (United States)

    McKechnie, Timothy N. (Inventor); Antony, Leo V. M. (Inventor); O'Dell, Scott (Inventor); Power, Chris (Inventor); Tabor, Terry (Inventor)

    2009-01-01

    Ultra fine and nanometer powders and a method of producing same are provided, preferably refractory metal and ceramic nanopowders. When certain precursors are injected into the plasma flame in a reactor chamber, the materials are heated, melted and vaporized and the chemical reaction is induced in the vapor phase. The vapor phase is quenched rapidly to solid phase to yield the ultra pure, ultra fine and nano product. With this technique, powders have been made 20 nanometers in size in a system capable of a bulk production rate of more than 10 lbs/hr. The process is particularly applicable to tungsten, molybdenum, rhenium, tungsten carbide, molybdenum carbide and other related materials.

  6. Personality in teams: its relationship to social cohesion, task cohesion, and team performance

    NARCIS (Netherlands)

    van Vianen, A.E.M.; de Dreu, C.K.W.

    2001-01-01

    This study continued past research on the relationship between personality composition in teams and social cohesion and team performance (Barrick, Stewart, Neubert, & Mount, 1998). Results from the Barrick et al. sample (N = 50) were compared with data from two new samples, one comprising drilling t

  7. Overtopping breaching of cohesive homogeneous earth dam with different cohesive strength

    Institute of Scientific and Technical Information of China (English)

    ZHANG JianYun; LI Yun; XUAN GuoXiang; WANG XiaoGang; LI Jun

    2009-01-01

    dumping collapse.When the cohesive strength is smaller,the breach process becomes faster,and the peak outflow,the final width and depth of breach become bigger.The main character of the breach formation is single level head cutting and shearing collapse.

  8. Personality in teams: its relationship to social cohesion, task cohesion, and team performance

    NARCIS (Netherlands)

    van Vianen, A.E.M.; de Dreu, C.K.W.

    2001-01-01

    This study continued past research on the relationship between personality composition in teams and social cohesion and team performance (Barrick, Stewart, Neubert, & Mount, 1998). Results from the Barrick et al. sample (N = 50) were compared with data from two new samples, one comprising drilling

  9. Social cohesion – a post-crisis analysis

    Directory of Open Access Journals (Sweden)

    Alina Magdalena MANOLE

    2012-11-01

    Full Text Available Social cohesion is a complex notion, subject to various different approaches that we set out to analyse. Thus, the article presents the scientific views regarding social cohesion, both at an individual or group level and at a macro-social level. The concluding section presents the consequences for public policy of a pluralist approach to defining social cohesion, while underlining the importance of a bi-dimensional view – disparities/inequality/social exclusion and social relations/social bonds/social capital – in order to achieve a comprehensive vision of a society’s social cohesion.

  10. Dry Powder Precursors of Cubic Liquid Crystalline Nanoparticles (cubosomes)

    Science.gov (United States)

    Spicer, Patrick T.; Small, William B.; Small, William B.; Lynch, Matthew L.; Burns, Janet L.

    2002-08-01

    Cubosomes are dispersed nanostructured particles of cubic phase liquid crystal that have stimulated significant research interest because of their potential for application in controlled-release and drug delivery. Despite the interest, cubosomes can be difficult to fabricate and stabilize with current methods. Most of the current work is limited to liquid phase processes involving high shear dispersion of bulk cubic liquid crystalline material into sub-micron particles, limiting application flexibility. In this work, two types of dry powder cubosome precursors are produced by spray-drying: (1) starch-encapsulated monoolein is produced by spray-drying a dispersion of cubic liquid crystalline particles in an aqueous starch solution and (2) dextran-encapsulated monoolein is produced by spray-drying an emulsion formed by the ethanol-dextran-monoolein-water system. The encapsulants are used to decrease powder cohesion during drying and to act as a soluble colloidal stabilizer upon hydration of the powders. Both powders are shown to form (on average) 0.6 μm colloidally-stable cubosomes upon addition to water. However, the starch powders have a broader particle size distribution than the dextran powders because of the relative ease of spraying emulsions versus dispersions. The developed processes enable the production of nanostructured cubosomes by end-users rather than just specialized researchers and allow tailoring of the surface state of the cubosomes for broader application.

  11. Under-ice movement of cohesive sediments before river-ice breakup

    Science.gov (United States)

    Milburn, D.; Prowse, T. D.

    2002-03-01

    A significant body of research exists on river hydraulics and sediment transport during open-water conditions, and to a lesser extent during the period of ice-cover. Most of the ice-related studies, however, are based on controlled laboratory experiments or field studies conducted under stable ice-cover conditions. They have largely ignored the most dynamic periods, such as breakup, when hydraulic conditions are most rapidly changing and energy levels are maximized. Moreover, the entire pre-breakup to ice-clearance period is virtually devoid of even standard hydrometric measurements of suspended sediment, largely because of safety and logistic problems. Some recent work has pointed to the formation of a sediment plume comprising fine-grained sediments that develops before the main breakup fracturing of the ice cover. This plume has been noted as being particularly ecologically significant because it can contain the winter-long deposition of contaminants that preferentially attach to fine-grained material. Unfortunately, however, because measurements of the critical parameters affecting sediment transport during these periods are rarely taken, much uncertainty remains about the hydraulic forces that resuspend and transport sediments under an ice cover, and particularly for cohesive fine-grained sediments. This paper describes a field experiment designed to broaden our understanding of sediment transport during this critical pre-breakup period. Detailed measurements of river stage, ice elevations, flow velocity profiles and suspended sediment were taken over a 17-day period just before the 1998 river-ice breakup at Hay River, Northwest Territories, Canada. Results indicated that just before breakup, the shear stress, which governs the beginning of sediment motion, increases dramatically and drives the development of the under-ice sediment plume of very fine-grained, cohesive sediments. The shear stress in this case became critical at a mean under-ice velocity of 0·4

  12. Cow dung powder poisoning

    Directory of Open Access Journals (Sweden)

    Khaja Mohideen Sherfudeen

    2015-01-01

    Full Text Available Cow dung, which has germicidal property, was used in ancient days to clean living premises in South India. Nowadays, people are using commercially available synthetic cow dung powder. It is locally known as "saani powder" in Tamil Nadu. It is freely available in homes and is sometimes accidentally consumed by children. It is available in two colors - yellow and green. Cow dung powder poisoning is common in districts of Tamil Nadu such as Coimbatore, Tirupur, and Erode. We report two cases of yellow cow dung powder poisoning from our hospital.

  13. Cow dung powder poisoning.

    Science.gov (United States)

    Sherfudeen, Khaja Mohideen; Kaliannan, Senthil Kumar; Dammalapati, Pavan Kumar

    2015-11-01

    Cow dung, which has germicidal property, was used in ancient days to clean living premises in South India. Nowadays, people are using commercially available synthetic cow dung powder. It is locally known as "saani powder" in Tamil Nadu. It is freely available in homes and is sometimes accidentally consumed by children. It is available in two colors - yellow and green. Cow dung powder poisoning is common in districts of Tamil Nadu such as Coimbatore, Tirupur, and Erode. We report two cases of yellow cow dung powder poisoning from our hospital.

  14. Key Skills for Science Learning: The Importance of Text Cohesion and Reading Ability

    Science.gov (United States)

    Hall, Sophie Susannah; Maltby, John; Filik, Ruth; Paterson, Kevin B.

    2016-01-01

    To explore the importance of text cohesion, we conducted two experiments. We measured online (reading times) and offline (comprehension accuracy) processes for texts that were high and low cohesion. In study one (n?=?60), we manipulated referential cohesion using noun repetition (high cohesion) and synonymy (low cohesion). Students showed enhanced…

  15. Iconicity of cohesion in Persian causative constructions

    Directory of Open Access Journals (Sweden)

    Mohammad Ali Salmani Nodoushan

    2014-12-01

    Full Text Available This paper tries to show that Persian causative constructions are not only iconic in nature but also employ iconicity of cohesion in their syntactic structures productively. It starts with a description of iconicity and specifically focuses on the notion of conceptual distance as discussed by Haiman (1983. It then briefly reviews the formal typology of causative constructions (i. e., lexical, morphological, and periphrastic and summarizes the ideas proposed by Comrie (1989, Dixon (2000, Shibatani (1976, and Talmy (2003 to come up with a list of, and a table for, the semantic properties of causative constructions (i. e., directness, coercion, control, manipulation, separability, and clause structure. The paper then presents tangible evidence and examples from Persian to claim that the linguistic distance observed between [Vcause] and [Veffect] in different types of Persian causative constructions mirrors the conceptual distance between them, and concludes that the iconic nature of causative constructions in Persian can be explained on the basis of the principle of iconicity of cohesion. It lends support to the universality of the principles of functional-cognitive linguistics and shows that iconicity theory still has a high potential for explaining form-meaning relations in different syntactic structures.

  16. Roller compaction: Effect of relative humidity of lactose powder.

    Science.gov (United States)

    Omar, Chalak S; Dhenge, Ranjit M; Palzer, Stefan; Hounslow, Michael J; Salman, Agba D

    2016-09-01

    The effect of storage at different relative humidity conditions, for various types of lactose, on roller compaction behaviour was investigated. Three types of lactose were used in this study: anhydrous lactose (SuperTab21AN), spray dried lactose (SuperTab11SD) and α-lactose monohydrate 200M. These powders differ in their amorphous contents, due to different manufacturing processes. The powders were stored in a climatic chamber at different relative humidity values ranging from 10% to 80% RH. It was found that the roller compaction behaviour and ribbon properties were different for powders conditioned to different relative humidities. The amount of fines produced, which is undesirable in roller compaction, was found to be different at different relative humidity. The minimum amount of fines produced was found to be for powders conditioned at 20-40% RH. The maximum amount of fines was produced for powders conditioned at 80% RH. This was attributed to the decrease in powder flowability, as indicated by the flow function coefficient ffc and the angle of repose. Particle Image Velocimetry (PIV) was also applied to determine the velocity of primary particles during ribbon production, and it was found that the velocity of the powder during the roller compaction decreased with powders stored at high RH. This resulted in less powder being present in the compaction zone at the edges of the rollers, which resulted in ribbons with a smaller overall width. The relative humidity for the storage of powders has shown to have minimal effect on the ribbon tensile strength at low RH conditions (10-20%). The lowest tensile strength of ribbons produced from lactose 200M and SD was for powders conditioned at 80% RH, whereas, ribbons produced from lactose 21AN at the same condition of 80% RH showed the highest tensile strength. The storage RH range 20-40% was found to be an optimum condition for roll compacting three lactose powders, as it resulted in a minimum amount of fines in the

  17. Deformed liquid marbles: Freezing drop oscillations with powders

    KAUST Repository

    Marston, Jeremy

    2012-09-01

    In this work we show that when a liquid drop impacts onto a fine-grained hydrophobic powder, the final form of the drop can be very different from the spherical form with which it impacts. In all cases, the drop rebounds due to the hydrophobic nature of the powder. However, we find that above a critical impact speed, the drop undergoes a permanent deformation to a highly non-spherical shape with a near-complete coverage of powder, which then freezes the drop oscillations during rebound. © 2012 Elsevier B.V.

  18. Plasma preparation and low-temperature sintering of spherical TiC-Fe composite powder

    Institute of Scientific and Technical Information of China (English)

    Jian-jun Wang; Jun-jie Hao; Zhi-meng Guo; Song Wang

    2015-01-01

    A spherical Fe matrix composite powder containing a high volume fraction (82vol%) of fine TiC reinforcement was produced us-ing a novel process combining in situ synthesis and plasma techniques. The composite powder exhibited good sphericity and a dense struc-ture, and the fine sub-micron TiC particles were homogeneously distributed in theα-Fe matrix. A TiC–Fe cermet was prepared from the as-prepared spherical composite powder using powder metallurgy at a low sintering temperature;the product exhibited a hardness of HRA 88.5 and a flexural strength of 1360 MPa. The grain size of the fine-grained TiC and special surface structure of the spherical powder played the key roles in the fabrication process.

  19. Preparation of Ultra-fine Aluminum Nitride in Thermal Plasma

    Institute of Scientific and Technical Information of China (English)

    漆继红; 罗义文; 印永祥; 代晓雁

    2002-01-01

    Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor. The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror (SEM), and the purity is at least over 90% evaluated by X-Ray diffraction (XRD). The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3. Typical experimental parameters such as the feed rate of raw material, the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.

  20. Influence of primary crystallisation conditions on the mechanical and interfacial properties of micronised budesonide for dry powder inhalation.

    Science.gov (United States)

    Kubavat, Harshal A; Shur, Jagdeep; Ruecroft, Graham; Hipkiss, David; Price, Robert

    2012-07-01

    Investigate the influence of primary crystallisation conditions on the mechanical properties and secondary processing behaviour of budesonide for dry powder inhaler (DPI) formulations. Young's modulus of two batches of budesonide crystals (samples A and B) produced using different anti-solvents was determined using nanoindentation. Physicochemical and surface interfacial properties via the cohesive-adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) of air-jet micronised budesonide crystals were also investigated. These data were correlated to in vitro aerosolization performance of carrier-based DPI formulations containing either budesonide samples A or B and lactose monohydrate. Young's modulus of budesonide samples A and B crystals was 0.95 and 4.04 GPa, respectively. Sample A crystals with low Young's modulus exhibited poorer micronisation efficiency than sample B. CAB analysis of micronised budesonide samples A and B, suggest that sample B budesonide had a greater adhesion to lactose than sample A. These data correlated with in vitro aerosolisation studies, which showed that the fine particle delivery of budesonide sample A was higher than that of sample B. In conclusion, crystallisation conditions may affect the mechanical properties of budesonide, and therefore secondary processing of the material and their interfacial properties and product performance in carrier based DPI formulations. Copyright © 2012 Elsevier B.V. All rights reserved.

  1. Characterizing delamination of fibre composites by mixed mode cohesive laws

    DEFF Research Database (Denmark)

    Sørensen, Bent F.; Jacobsen, Torben K.

    2009-01-01

    A novel method is used for the determination of mixed mode cohesive laws and bridging laws for the characterisation of crack bridging in composites. The approach is based on an application of the J integral. The obtained cohesive laws were found to possess high peak stress values. Mixed mode...

  2. Introducing Semantic Cohesion Analysis: A Study of Group Talk.

    Science.gov (United States)

    Friedlander, Myrna L.; And Others

    1985-01-01

    Cohesive talk was observed over time and across psychotherapy groups led by self-disclosing or nondisclosing therapists. Despite individual therapist differences, the nondisclosing groups showed more cohesive interactions throughout therapy. No differences were observed in clients' perceptions of therapists or their attraction to the group.…

  3. An Analysis of Lexical Cohesion in"How Empathy Unfolds"

    Institute of Scientific and Technical Information of China (English)

    朱玲霞

    2016-01-01

    This thesis aims to analyze the lexical cohesion in the text"How Empathy Unfolds" in the new standard college English textbook. This paper focuses on four kinds of lexical cohesive devices: repetition, synonymy, hyponymy and collocation. It is expected that these analyses can help readers gain a better and deeper comprehension of the structure and content of the text.

  4. Some Observations on Cohesion and Coherence in Simplified Texts.

    Science.gov (United States)

    Lautamatti, Liisa

    Analysis of several texts simplified to teach reading comprehension to college second language students shows that simplification affects both textual cohesion and coherence. Moreover, simplification restricts the amount of significant semantic information and creates a more transparent pattern of reference. The use of cohesive conjunctions varies…

  5. Textual Cohesion and Coherence in Children's Writing Revisited.

    Science.gov (United States)

    Spiegel, Dixie Lee; Fitzgerald, Jill

    1990-01-01

    Examines the relationship between cohesion and coherence in children's writing. Finds evidence of a relationship between cohesion and coherence, and reports that this relationship (1) varies according to text content; (2) does not vary according to quality of writing; and (3) does not vary according to the students' grade level. (KEH)

  6. A cohesive segments method for the simulation of crack growth

    NARCIS (Netherlands)

    Remmers, J.J.C.; De Borst, R.; Needleman, A.

    2003-01-01

    A numerical method for crack growth is described in which the crack is not regarded as a single discontinuity that propagates continuously. Instead, the crack is represented by a set of overlapping cohesive segments. These cohesive segments are inserted into finite elements as discontinuities in the

  7. The Social Cohesion Role of the Public Sector

    Science.gov (United States)

    Capshaw, N. Clark

    2005-01-01

    Social cohesion, the "glue" that keeps a society together, is influenced by the various sectors or "pillars" of that society-educational institutions, social and religious institutions, business institutions, and government. In this article, the effect of the three branches of government (executive, legislative, and judicial) on social cohesion is…

  8. Leadership Status Congruency and Cohesion in Outdoor Expedition Groups

    Science.gov (United States)

    Eys, Mark A.; Ritchie, Stephen; Little, Jim; Slade, Heather; Oddson, Bruce

    2008-01-01

    The purpose of the present study was to examine the relationship between status congruency and group cohesion in outdoor expedition groups in an educational setting. Specifically, three aspects of status congruency were assessed in relation to group cohesion in four adventure canoe groups. The groups participated in 2-week expeditions in the…

  9. Exploring Group Cohesion in a Higher Education Field Experience

    Science.gov (United States)

    Malcarne, Brian Keith

    2012-01-01

    The purpose of this study was to gain understanding into the experience of group cohesion for university students participating in an academic field experience. A mixed methods approach was used following a two-phase, sequential research design to help provide a more complete explanation of how group cohesion was impacted by the field experience.…

  10. A Reappraisal of Lexical Cohesion in Conversational Discourse

    Science.gov (United States)

    Gomez Gonzalez, Maria De Los Angeles

    2013-01-01

    Cohesion, or the connectedness of discourse, has been recognized as playing a crucial role in both language production and comprehension processes. Researchers have debated about the "right" number and classification of cohesive devices, as well as about their interaction with coherence and/or genre. The present study proposes an integrative model…

  11. Cohesion in Online Student Teams versus Traditional Teams

    Science.gov (United States)

    Hansen, David E.

    2016-01-01

    Researchers have found that the electronic methods in use for online team communication today increase communication quality in project-based work situations. Because communication quality is known to influence group cohesion, the present research examined whether online student project teams are more cohesive than traditional teams. We tested…

  12. Effect of Alignment on Text Cohesion in the Continuation Task

    Science.gov (United States)

    Jiang, Lin; Xu, Xin

    2016-01-01

    A continuation task provides learners with a text with its ending removed and requires them to complete it through writing in a most coherent and logical way. The current study investigated (a) whether the continuation task had a positive effect on text cohesion and (b) whether texts produced by pairs exhibited higher cohesion than those produced…

  13. Forgiveness and Cohesion in Familial Perceptions of Alcohol Misuse

    Science.gov (United States)

    Scherer, Michael; Worthington, Everett L.; Hook, Joshua N.; Campana, Kathryn L.; West, Steven L.; Gartner, Aubrey L.

    2012-01-01

    The authors examine the relationships between forgiveness, family cohesion, and alcohol. In Study 1 (N = 190), participants reported lower levels of trust and forgiveness for family members who misuse alcohol. In Study 2 (N = 141), the authors present a model demonstrating family cohesion and trait forgiveness related to state forgiveness of an…

  14. A Study of Cohesive Devices in English IM

    Institute of Scientific and Technical Information of China (English)

    MA Shu-yun

    2011-01-01

    The main purpose of the present research is to reveal features of the use of cohesive devices in English IM (Instant Message).In order to be accurate and explicit,Oxford WordSmith Tools (Version 4.0) is applied to investigate the frequency of each type of cohesive devices used by online-communicators.Cohesion in English IM is characterized by a number of distinguishing features:1) this genre of discourse makes abundant use of cohesive ties such as personal reference,lexical reiteration and ellipsis; 2) substitution and comparative reference are rarely applied; 3) The variety of conjunctions used is limited,and the most frequently used conjunctions are and,so,but and or.In analyzing the cohesive effect of each cohesive device,it is held that in order to overcome the limitations of the messaging systems and to achieve smooth communication,participants mainly adopt explicit cohesive ties which could achieve stronger force of cohesion in IM communication.

  15. 18Regional integration and social cohesion: Perspectives from the ...

    African Journals Online (AJOL)

    between social cohesion and regional integration in the developing world. Candice ... of public policy, and the EU even prioritises the EU Social Cohesion Funds in its .... networks of ethnic entrepreneurs and grassroots non-state actors. ... definitions and issues', Paper SRA-309, Strategic Research and Analysis Directorate,.

  16. Mechanical properties and spalling at elevated temperature of high performance concrete made with reactive and waste inert powders

    OpenAIRE

    Ali, Msheer Hasan; Dinkha, Youkhanna Zayia; James H. Haido

    2017-01-01

    In this article, the efficiency of waste glass powder was investigated in enhancing the mechanical properties of concrete at high temperature. Chemical composition of this powder reveals that it plays good role as effective inert very fine material in concrete strength improvement. Conventional reactive pozzolanic powder of silica fume was used also in present work to show the degradation degree in concrete strength under firing in comparison to concrete made with waste glass powder. The expe...

  17. Editing ’Father & Son’: Coherence and Cohesion

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Introduction Some writing is good in sentence structure but either poor in coherence or in cohesion. The problem of coherence is that the sequence of information is not always clear and the problem of cohesion is that the sequence of information is acceptable, while the connection between it is not so good. The question is how to analyze and improve these different weakness in writing. We have two methods. One to focus on coherence, the other to focus on cohesion. In this essay, the method used is based on the principle that coherence and cohesion should work together. I use this approach as a tool to edit and display the analysis of coherence and cohesion in the passage entitled ’ Father & Son". This passage is presented as a guided writing exercise in College English Course, Intensive Reading, Band 3, p271.

  18. Research on cohesive sediment erosion by flow: An overview

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Erosion of cohesive sediment by flow is a very complicated phenomenon occurring worldwide. Understanding and modeling of the erosion process are important for many issues such as the breaching of embankments, riverbank stability, siltation of harbors and navigation channels, service life of reservoirs, distribution of (heavy metal) pollutants and water quality problems. In the last few decades, numerous studies have been done on the erosion of cohesive sediment by flow. Nevertheless, the factors affecting the erosion resistance of cohesive sediment are still not fully understood and the knowledge of the physics of cohesive sediment erosion is in- adequate, as a result the mathematical modeling of this erosion is far from satis- factory. In this paper an overview of the studies on the erosion resistance, erosion threshold and the erosion rate of cohesive sediment by flow is presented. The outcomes achieved so far from the studies and the existing problems have been analyzed and summarized, based on which recommendations are proposed for future research.

  19. European Cohesion Policy: A Proposed Evaluation Model

    Directory of Open Access Journals (Sweden)

    Alina Bouroşu (Costăchescu

    2012-06-01

    Full Text Available The current approach of European Cohesion Policy (ECP is intended to be a bridge between different fields of study, emphasizing the intersection between "the public policy cycle, theories of new institutionalism and the new public management”. ECP can be viewed as a focal point between putting into practice the principles of the new governance theory, theories of economic convergence and divergence and the governance of common goods. After a short introduction of defining the concepts used, the author discussed on the created image of ECP by applying three different theories, focusing on the structural funds implementation system (SFIS, directing the discussion on the evaluation part of this policy, by proposing a model of performance evaluation of the system, in order to outline key principles for creating effective management mechanisms of ECP.

  20. Lexicai Cohesion in Hearrt of Dartkness

    Institute of Scientific and Technical Information of China (English)

    马画

    2012-01-01

    Heart of Darkness, written by famous English novelist Joseph Conrad, is one of the most influential novellas in the 20^th century with its profound thoughts, remarkable artistry, unique double narrative structure, abundant metaphors and symbolic social meaning, has vivid stylistic features. This paper, by analyzing the novella from the angle of lexical cohesion, will help us know how the author achieves his literary meaning by making linguistic choices. The analysis of the novella from functional stylistic angle is of great stylistic siguificance and social significance. The aim of the textual analysis of Heart of Darkness is to find linguistic evidence for the reader's interpretation and the critical evaluation of the novella, which can also help college students appreciate and analyze literary texts, cultivating their ability in understanding and appreciating themes in literary works from a linguistic perspective.

  1. Measurement of Cohesion in Asteroid Regolith Materials

    Science.gov (United States)

    Kleinhenz, Julie; Gaier, James; Waters, Deborah; Harvey, Ralph; Zeszut, Zoe; Carreno, Brandon; Shober, Patrick

    2017-01-01

    There is increasing evidence that a large fraction of asteroids, and even Phobos, have such low densities (asteroids are thought to be made up of unconsolidated smaller particles of varying size referred to as rubble piles. Images of the asteroid Itokawa reinforce this hypothesis. What holds the rubble piles together? Gravitational forces alone are not strong enough to hold together rubble pile asteroids, at least not those that are rapidly spinning Van der Waals forces and or Electrostatic forces must therefore be responsible for holding them together. Previous work suggests that electrostatic forces, which are orders of magnitude stronger are far more likely. Charge build-up is a likely consequence of the interaction of airless bodies with the solar wind plasma, analogous to what has been proposed to occur on the moon. Objective: Experimentally measure cohesive forces relevant to those holding rubble pile asteroids together

  2. [Food education: health and social cohesion].

    Science.gov (United States)

    Aparici, Eva Zafra

    2017-01-01

    Using a theoretical-reflexive approach, this article connects the results of various qualitative studies in social conflict and medical anthropology, in order to investigate how food can be a tool for social transformation in terms of health but also in terms of the dialogue, respect and coexistence among people, groups and communities. In this sense the article presents a first approximation to a new theoretical and methodological approach to food education. In this approach, food adopts a political, sociocultural and participatory perspective that brings us closer to an innovative understanding of the phenomenon of food: not only as an analytic and diagnostic tool, but also as an instrument for health education interventions toward conflict resolution and the promotion of healthier societies overall - nutritionally, but also in terms of equality and social cohesion.

  3. Food education: health and social cohesion

    Directory of Open Access Journals (Sweden)

    Eva Zafra Aparici

    2017-07-01

    Full Text Available Using a theoretical-reflexive approach, this article connects the results of various qualitative studies in social conflict and medical anthropology, in order to investigate how food can be a tool for social transformation in terms of health but also in terms of the dialogue, respect and coexistence among people, groups and communities. In this sense the article presents a first approximation to a new theoretical and methodological approach to food education. In this approach, food adopts a political, sociocultural and participatory perspective that brings us closer to an innovative understanding of the phenomenon of food: not only as an analytic and diagnostic tool, but also as an instrument for health education interventions toward conflict resolution and the promotion of healthier societies overall – nutritionally, but also in terms of equality and social cohesion.

  4. Psychobiological Assessment and Enhancement of Team Cohesion and Psychological Resilience in ROTC Cadets Using a Virtual-Reality Team Cohesion Test

    Science.gov (United States)

    2016-06-01

    AWARD NUMBER: W81XWH-15-1-0042 TITLE: Psychobiological Assessment and Enhancement of Team Cohesion and Psychological Resilience in ROTC Cadets...Team Cohesion and Psychological Resilience in ROTC Cadets Using a Virtual-Reality Team Cohesion Test 5b. GRANT NUMBER W81XWH-15-1-0042 5c. PROGRAM...and Enhancement of Team Cohesion and Psychological Resilience using a Virtual Team Cohesion Test JW140070, W81XWH-15-1-0042 PI: Dr. Josh Woolley

  5. Assessment of Pharmaceutical Powder Flowability using Shear Cell-Based Methods and Application of Jenike's Methodology.

    Science.gov (United States)

    Jager, Paul D; Bramante, Tommasina; Luner, Paul E

    2015-11-01

    Jenike's approach to hopper design for a large-scale (3150 L) conical hopper was applied to pharmaceutical powders to evaluate flow issues, such as funnel flow or cohesive arching. Seven grades of microcrystalline cellulose (MCC) and six powder blends were tested. A Schulze Ring Shear Tester measured the flow function, wall friction (using stainless steel coupons with a #2B or #8 finish) and compressibility. Hopper Index (HI, maximum hopper angle required for mass flow) and Arching Index (AI, minimum hopper outlet size to prevent cohesive arch formation) were computed using Mathcad(©) . For MCC, a linear relationship was observed between median particle size and the Jenike flow function coefficient. A curvilinear relationship was observed for powder blends indicating more complex flow behavior than based on median particle size alone. Powder bulk density had a minimal effect on AI for MCC grades. Overestimation of AI can occur with this method for pharmaceutical powders because the true shape of the flow function is not defined at very low consolidation pressures and linear extrapolation becomes unrepresentative. This instrumental limitation underscores the need for a precise and accurate test method to determine powder flow functions at very low levels of consolidation stress for pharmaceutical applications.

  6. The tool for the automatic analysis of text cohesion (TAACO): Automatic assessment of local, global, and text cohesion.

    Science.gov (United States)

    Crossley, Scott A; Kyle, Kristopher; McNamara, Danielle S

    2016-12-01

    This study introduces the Tool for the Automatic Analysis of Cohesion (TAACO), a freely available text analysis tool that is easy to use, works on most operating systems (Windows, Mac, and Linux), is housed on a user's hard drive (rather than having an Internet interface), allows for the batch processing of text files, and incorporates over 150 classic and recently developed indices related to text cohesion. The study validates TAACO by investigating how its indices related to local, global, and overall text cohesion can predict expert judgments of text coherence and essay quality. The findings of this study provide predictive validation of TAACO and support the notion that expert judgments of text coherence and quality are either negatively correlated or not predicted by local and overall text cohesion indices, but are positively predicted by global indices of cohesion. Combined, these findings provide supporting evidence that coherence for expert raters is a property of global cohesion and not of local cohesion, and that expert ratings of text quality are positively related to global cohesion.

  7. On the Application of News Grammatical Cohesion in Discourse%On the Application of News Grammatical Cohesion in Discourse

    Institute of Scientific and Technical Information of China (English)

    郭恒达

    2011-01-01

    A discourse is the combination of various sentences. These sentences are supposed to be not only cohesive in construction, but coherent in semantics. With the theory of cohesion this paper analyzes how they are applied in a news discourse in order to help readers and learners gain deeper understanding of a news discourse.

  8. Self-ignition and ignition of aluminum powders in shock waves

    Science.gov (United States)

    Boiko, V. M.; Poplavski, S. V.

    Ignition of fine aluminum powders in reflected shock waves has been studied. Two ignition regimes are found: self-ignition observed at temperatures higher than 1800 K and ``low-temperature'' ignition at temperatures of 1000-1800 K. The possibility of initiating the ignition of aluminum powders in air using combustible liquids has been studied too.

  9. Comparison of the mechanically alloyed (V,W)C and (V,W)C-co powders

    CSIR Research Space (South Africa)

    Bolokang, AS

    2008-01-01

    Full Text Available in XRD patterns because they were of extremely fine grain size.As a result of the loss ofVandWthrough oxidation, free carbonwas also found in the final powder. The lattice parameter of the (V,W)C powder increased with milling time up to a maximum...

  10. New coal dewatering technology turns sludge to powder

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2009-03-15

    Virginian Tech's College of Engineering's Roe-Hoan Yoon and his group have developed a hyperbaric centrifuge that can dewater coal as fine as talcum powder. Such coal fines presently must be discarded by even the most advanced coal cleaning plants because of their high moisture content. The new technology can be used with the Microcel technology to remove ash, to re-mine the fine coal discarded to impoundments and to help minimize waste generation. Virginia Tech has received $1 million in funding from the US Department of State to also help the Indian coal industry produce a cleaner product. 1 photo.

  11. Fine Sediment Resuspension Dynamics in Moreton Bay

    Institute of Scientific and Technical Information of China (English)

    YOU Zai-jin; YIN Bao-shu

    2007-01-01

    A comprehensive field study has been undertaken to investigate sediment resuspension dynamics in the Moreton Bay, a large semi-enclosed bay situated in South East Queensland, Australia. An instrumented tripod, which housed three current meters, three OBS sensors and one underwater video camera, was used to collect the field data on tides, currents, waves and suspended sediment concentrations at four sites (Sites 1, 2, 4, and 5) in the bay. Site 1 was located at the main entrance, Site 2 at the central bay in deep water, and Sites 4 and 5 at two small bays in shallow water. The bed sediment was fine sand (d50=0.2 mm) at Site 1, and cohesive sediment at the other three sites. Based on the collected field data, it is found that the dominant driving forces for sediment resuspension are a combination of ocean swell and tidal currents at Site 1, tidal currents at Site 2, and wind-waves at Sites 4 and 5. The critical bed shear stress for cohesive sediment resuspension is determined as 0.079 Pa in unidirectional flow at Site 2, and 0.076 Pa in wave-induced oscillatory flow at Site 5.

  12. Achyrocline satureioides (Lam.) DC., Asteraceae: development of granules from spray dried powder

    OpenAIRE

    Petrovick,Gustavo F.; Pedro R. Petrovick; Valquiria L. Bassani

    2010-01-01

    Achyrocline satureioides (Lam.) DC., Asteraceae, is a herbal specie widely used in folk medicine in the south of Brazil, Uruguay, Argentina and Paraguay. The technological characteristics of an Achyrocline satureioides spray dried extract powder, produced in semi-industrial scale, as well as the feasibility of the granules are reported in the present work. The spray dried powder was characterized as a fine powder consisting of small spherical particles with rough and porous surface. The Hausn...

  13. Production and Characterization of Atomized U-Mo Powder by the Rotating Electrode Process

    Energy Technology Data Exchange (ETDEWEB)

    C.R. Clark; B.R. Muntifering; J.F. Jue

    2007-09-01

    In order to produce feedstock fuel powder for irradiation testing, the Idaho National Laboratory has produced a rotating electrode type atomizer to fabricate uranium-molybdenum alloy fuel. Operating with the appropriate parameters, this laboratory-scale atomizer produces fuel in the desired size range for the RERTR dispersion experiments. Analysis of the powder shows a homogenous, rapidly solidified microstructure with fine equiaxed grains. This powder has been used to produce irradiation experiments to further test adjusted matrix U-Mo dispersion fuel.

  14. Dry mixing and coating of powders

    Directory of Open Access Journals (Sweden)

    Alonso, M.

    1999-10-01

    Full Text Available This paper presents a review on the mixing and coating of powders by dry processes. The review surveys fundamental works on mixture characterization (mixing index definitions and sampling techniques, mixing mechanisms and models, segregation with especial emphasis on free-surface segregation, mixing of cohesive powders and interparticle forces, ordered mixing (dry coating including mechanism, model and applications and mixing equipment selection.

    En este artículo se presenta una revisión bibliográfica sobre el mezclado y recubrimiento de materiales pulverulentos mediante procesos por vía seca. La revisión incluye trabajos fundamentales sobre caracterización de mezclas (definiciones de índices de mezclado y técnicas de muestreo, mecanismos y modelos de mezclado, segregación con especial énfasis en la segregación de superficie libre, mezclado de polvos cohesivos y fuerzas interpartículas, mezcla ordenada (recubrimiento incluyendo mecanismo, modelo y aplicaciones, y selección de equipos de mezclado.

  15. Microstructural development of rapid solidification in Al-Si powder

    Energy Technology Data Exchange (ETDEWEB)

    Jin, Feng [Iowa State Univ., Ames, IA (United States)

    1995-09-26

    The microstructure and the gradient of microstructure that forms in rapidly solidificated powder were investigated for different sized particles. High pressure gas atomization solidification process has been used to produce a series of Al-Si alloys powders between 0.2 μm to 150 μm diameter at the eutectic composition (12.6 wt pct Si). This processing technique provides powders of different sizes which solidify under different conditions (i.e. interface velocity and interface undercooling), and thus give different microstructures inside the powders. The large size powder shows dendritic and eutectic microstructures. As the powder size becomes smaller, the predominant morphology changes from eutectic to dendritic to cellular. Microstructures were quantitatively characterized by using optical microscope and SEM techniques. The variation in eutectic spacing within the powders were measured and compared with the theoretical model to obtain interface undercooling, and growth rate during the solidification of a given droplet. Also, nucleation temperature, which controls microstructures in rapidly solidified fine powders, was estimated. A microstructural map which correlates the microstructure with particle size and processing parameters is developed.

  16. Characterization of commercially pure aluminum powder for research reactor fuel plates

    Energy Technology Data Exchange (ETDEWEB)

    Downs, V.D. [Babcock and Wilcox Co., Lynchburg, VA (United States); Wiencek, T.C. [Argonne National Lab., IL (United States)

    1992-11-01

    Aluminum powder is used as the matrix material in the production of uranium aluminide, oxide, and silicide dispersion fuel plates for research and test reactors. variability in the characteristics of the aluminum powder, such as moisture content and particle-size distribution, influences blending and compacting of the aluminum/fuel powder. A detailed study was performed to characterize the physical properties of three aluminum powder lots. An angle-of-shear test was devised to characterize the cohesiveness of the aluminum powder. Flow-rate measurements, apparent density determination, subsieve analysis, surface area measurements, and scanning electron microscopy were also used in the study. It was found that because of the various types of commercially available powders, proper specification of powder variables will ensure the receipt of consistent raw materials. Improved control of the initial powder will reduce the variability of fuel-plate production and will improve overall plate reproducibility. It is recommended that a standard specification be written for the aluminum powder and silicide fuel.

  17. Characterization of commercially pure aluminum powder for research reactor fuel plates

    Energy Technology Data Exchange (ETDEWEB)

    Downs, V.D. (Babcock and Wilcox Co., Lynchburg, VA (United States)); Wiencek, T.C. (Argonne National Lab., IL (United States))

    1992-01-01

    Aluminum powder is used as the matrix material in the production of uranium aluminide, oxide, and silicide dispersion fuel plates for research and test reactors. variability in the characteristics of the aluminum powder, such as moisture content and particle-size distribution, influences blending and compacting of the aluminum/fuel powder. A detailed study was performed to characterize the physical properties of three aluminum powder lots. An angle-of-shear test was devised to characterize the cohesiveness of the aluminum powder. Flow-rate measurements, apparent density determination, subsieve analysis, surface area measurements, and scanning electron microscopy were also used in the study. It was found that because of the various types of commercially available powders, proper specification of powder variables will ensure the receipt of consistent raw materials. Improved control of the initial powder will reduce the variability of fuel-plate production and will improve overall plate reproducibility. It is recommended that a standard specification be written for the aluminum powder and silicide fuel.

  18. Cohesive Energies and Enthalpies: Complexities, Confusions, and Corrections.

    Science.gov (United States)

    Glasser, Leslie; Sheppard, Drew A

    2016-07-18

    The cohesive or atomization energy of an ionic solid is the energy required to decompose the solid into its constituent independent gaseous atoms at 0 K, while its lattice energy, Upot, is the energy required to decompose the solid into its constituent independent gaseous ions at 0 K. These energies may be converted into enthalpies at a given temperature by the addition of the small energies corresponding to integration of the heat capacity of each of the constituents. While cohesive energies/enthalpies are readily calculated by thermodynamic summing of the formation energies/enthalpies of the constituents, they are also currently intensively studied by computational procedures for the resulting insight on the interactions within the solid. In supporting confirmation of their computational results, authors generally quote "experimental" cohesive energies which are, in fact, simply the thermodynamic sums. However, these "experimental" cohesive energies are quoted in many different units, atom-based or calorimetric, and on different bases such as per atom, per formula unit, per oxide ion, and so forth. This makes comparisons among materials very awkward. Additionally, some of the quoted values are, in fact, lattice energies which are distinctly different from cohesive energies. We list large numbers of reported cohesive energies for binary halides, chalcogenides, pnictogenides, and Laves phase compounds which we bring to the same basis, and identify a number as incorrectly reported lattice energies. We also propose that cohesive energies of higher-order ionic solids may also be estimated as thermodynamic enthalpy sums.

  19. Molecular Intercalation and Cohesion of Organic Bulk Heterojunction Photovoltaic Devices

    KAUST Repository

    Bruner, Christopher

    2013-01-17

    The phase separated bulk heterojunction (BHJ) layer in BHJ polymer:fullerene organic photovoltaic devices (OPV) are mechanically weak with low values of cohesion. Improved cohesion is important for OPV device thermomechanical reliability. BHJ devices are investigated and how fullerene intercalation within the active layer affects cohesive properties in the BHJ is shown. The intercalation of fullerenes between the side chains of the polymers poly(3,3″′-didocecyl quaterthiophene) (PQT-12) and poly(2,5-bis(3-hexadecylthiophen-2-yl)thieno[3,2-b]thiophene (pBTTT) is shown to enhance BHJ layer cohesion. Cohesion values range from ≈1 to 5 J m -2, depending on the polymer:fullerene blend, processing conditions, and composition. Devices with non-intercalated BHJ layers are found to have significantly reduced values of cohesion. The resulting device power conversion efficiencies (PCE) are also investigated and correlated with the device cohesion. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Cohesion energetics of carbon allotropes: Quantum Monte Carlo study

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Hyeondeok; Kang, Sinabro; Koo, Jahyun; Lee, Hoonkyung; Kwon, Yongkyung, E-mail: ykwon@konkuk.ac.kr [Division of Quantum Phases and Devices, School of Physics, Konkuk University, Seoul 143-701 (Korea, Republic of); Kim, Jeongnim, E-mail: jnkim@ornl.gov [Materials Science and Technology Division and Computer Science and Mathematics Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States)

    2014-03-21

    We have performed quantum Monte Carlo calculations to study the cohesion energetics of carbon allotropes, including sp{sup 3}-bonded diamond, sp{sup 2}-bonded graphene, sp–sp{sup 2} hybridized graphynes, and sp-bonded carbyne. The computed cohesive energies of diamond and graphene are found to be in excellent agreement with the corresponding values determined experimentally for diamond and graphite, respectively, when the zero-point energies, along with the interlayer binding in the case of graphite, are included. We have also found that the cohesive energy of graphyne decreases systematically as the ratio of sp-bonded carbon atoms increases. The cohesive energy of γ-graphyne, the most energetically stable graphyne, turns out to be 6.766(6) eV/atom, which is smaller than that of graphene by 0.698(12) eV/atom. Experimental difficulty in synthesizing graphynes could be explained by their significantly smaller cohesive energies. Finally, we conclude that the cohesive energy of a newly proposed graphyne can be accurately estimated with the carbon–carbon bond energies determined from the cohesive energies of graphene and three different graphynes considered here.

  1. Cohesion Energetics of Carbon Allotropes: Quantum Monte Carlo Study

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Hyeondeok [Konkuk University, South Korea; Kang, Sinabro [Konkuk University, South Korea; Koo, Jahyun [Konkuk University, South Korea; Lee, Hoonkyung [Konkuk University, South Korea; Kim, Jeongnim [ORNL; Kwon, Yongkyung [Konkuk University, South Korea

    2014-01-01

    We have performed quantum Monte Carlo calculations to study the cohesion energetics of carbon allotropes, including sp3-bonded diamond, sp2-bonded graphene, sp-sp2 hybridized graphynes, and sp-bonded carbyne. The comput- ed cohesive energies of diamond and graphene are found to be in excellent agreement with the corresponding values de- termined experimentally for diamond and graphite, respectively, when the zero-point energies, along with the interlayer binding in the case of graphite, are included. We have also found that the cohesive energy of graphyne decreases system- atically as the ratio of sp-bonded carbon atoms increases. The cohesive energy of -graphyne, the most energetically- stable graphyne, turns out to be 6.766(6) eV/atom, which is smaller than that of graphene by 0.698(12) eV/atom. Experi- mental difficulty in synthesizing graphynes could be explained by their significantly smaller cohesive energies. Finally we conclude that the cohesive energy of a newly-proposed two-dimensional carbon network can be accurately estimated with the carbon-carbon bond energies determined from the cohesive energies of graphene and three different graphynes.

  2. Relationship between group cohesion and anxiety in soccer.

    Science.gov (United States)

    Borrego, Carla Chicau; Cid, Luis; Silva, Carlos

    2012-10-01

    Group cohesion in sport is a widely spread theme today. Research has found cohesion to be influenced by several individual and group components. Among the cognitive variables that relate to cohesion we found competitive anxiety. The purpose of this study was to examine the relation between task cohesion (ATG-T, and GI-T) and competitive state anxiety (A-state), and also if there would be a relation between cohesion and self-confidence. Participants were 366 football players of both genders male and female, aged between 15 to 23 years old, from Portugal's championships. Cohesion was measured using the Portuguese version of the Group Environment Questionnaire, and to assess competitive anxiety, we used the Portuguese version of the Competition State Anxiety Inventory 2. Our results show that female athletes report experiencing more cognitive anxiety and less self-confidence than male athletes. Only cognitive anxiety relates in a significantly negative way with the perception of cohesion (GI-T e ATG-T) in the total number of participants and in male athletes. Relatively to the somatic anxiety, it only relates negatively with the perception of the integration of the group in the total number of participants and in the male gender.

  3. An Investigation of Cohesion and Rhetorical Moves in Thesis Abstracts

    Directory of Open Access Journals (Sweden)

    Luthfiyah Luthfiyah

    2016-05-01

    Full Text Available This study aimed at investigating cohesion and rhetorical moves in thesis abstracts of English Education students. This study employed a qualitative research design in which 10 abstracts were chosen as samples. The cohesion is analyzed based on Halliday's and Hasan's  concept while rhetorical moves are analyzed based on Swales' and Feak's framework. The results show that all cohesive devices are used except substitution. Among those devices, reference is the most frequently used. The results also show that some cohesive devices are used incorrectly. As a result, seven abstracts (70% are still in medium category of cohesion level while three abstracts (30% are in high category of cohesion level. Furthermore, 7 abstracts are organized in different move patterns which do not follow the Swales' and Feak's framework. From the results of the study, it can be concluded that most of the abstract samples achieve medium category level of cohesion, and the rhetorical moves in most of the abstracts samples are not organized well. Permalink/DOI: http://dx.doi.org/10.15408/ijee.v2i2.3086

  4. Influence of polymeric additives on the cohesion and mechanical properties of calcium phosphate cements.

    Science.gov (United States)

    An, Jie; Wolke, Joop G C; Jansen, John A; Leeuwenburgh, Sander C G

    2016-03-01

    To expand the clinical applicability of calcium phosphate cements (CPCs) to load-bearing anatomical sites, the mechanical and setting properties of CPCs need to be improved. Specifically, organic additives need to be developed that can overcome the disintegration and brittleness of CPCs. Hence, we compared two conventional polymeric additives (i.e. carboxylmethylcellulose (CMC) and hyaluronan (HA)) with a novel organic additive that was designed to bind to calcium phosphate, i.e. hyaluronan-bisphosphonate (HABP). The unmodified cement used in this study consisted of a powder phase of α-tricalcium phosphate (α-TCP) and liquid phase of 4% NaH2PO4·2H2O, while the modified cements were fabricated by adding 0.75 or 1.5 wt% of the polymeric additive to the cement. The cohesion of α-TCP was improved considerably by the addition of CMC and HABP. None of the additives improved the compression and bending strength of the cements, but the addition of 0.75% HABP resulted into a significantly increased cement toughness as compared to the other experimental groups. The stimulatory effects of HABP on the cohesion and toughness of the cements is hypothesized to derive from the strong affinity between the polymer-grafted bisphosphonate ligands and the calcium ions in the cement matrix.

  5. Pourability Enhancement of PETN Explosive Powders

    Energy Technology Data Exchange (ETDEWEB)

    Vannet, M.D.; Ball, G.L.

    1987-01-01

    Manufacture of precision detonators requires the pelletizing of very fine, organic, crystalline explosive powders. Production of pellets in automatic machines within critical dimensional and weight tolerances requires that the powders pour uniformly into die cavities. The pellets must be able to be initiated with low energy and have a predictable energy output. Modifications to needle-like crystalline PETN explosive powders to make them pourable were introduced by the application of about 80 A thick polymeric coatings to the individual crystals, followed by a controlled agglomeration into a spherical prill. Microencapsulation techniques provided the key to achieving the result using less than 0.5 wt. % coating (an order of magnitude less coating than in usual PBX systems). These coatings did not appreciably alter the energy required to initiate and significantly increased the strength of the pellets. A key point demonstrated, which may be translated to other applications, was that powders that exhibit performance based on physical characteristics could have their handling and strength properties tailored with little change in their primary function.

  6. Coach-initiated motivational climate and cohesion in youth sport.

    Science.gov (United States)

    Eys, Mark A; Jewitt, Eryn; Evans, M Blair; Wolf, Svenja; Bruner, Mark W; Loughead, Todd M

    2013-09-01

    The general purpose of the present study was to examine the link between cohesion and motivational climate in youth sport. The first specific objective was to determine if relationships demonstrated in previous research with adult basketball and handball participants would be replicated in a younger sample and with a more heterogeneous set of sports. The second specific objective was to examine whether sources of athlete enjoyment moderate the relationships between motivational climate and cohesion. Athletes (N = 997; 532 girls and 465 boys; Mage = 15.26 +/- 1.20 years) completed measures pertaining to coach-initiated motivational climate, cohesion, and sources of enjoyment. Bivariate and canonical correlations revealed positive correlations between perceptions of a task-involving motivational climate and both task and social cohesion, while ego-involving motivational climate was negatively related. Cluster analyses suggested that individuals perceiving a low task-involving climate and high ego-involving climate perceived their teams as less cohesive. Finally, the degree to which participants derived enjoyment through other-referenced competency served as a moderator in the motivational climate-task cohesion relationship. Specifically, the relationship between task cohesion and motivational climate was more pronounced for those individuals who were less likely to derive enjoyment through other-referenced competency. Youth athletes' perceptions of coach-initiated motivational climate are related to cohesion. This relationship is, however, moderated by the degree to which athletes derive enjoyment through other-referenced competency. Motivational climate is an important variable to consider within team-building protocols intent on developing cohesion.

  7. Nutritional composition of ginger powder prepared using various drying methods.

    Science.gov (United States)

    Sangwan, A; Kawatra, A; Sehgal, S

    2014-09-01

    A study was undertaken to prepare ginger powder using various drying methods and their nutritional evaluation was carried out. Ginger (Zingiber officinale) was dried using shade, solar, oven and microwave drying methods. All the samples were ground in grinder to make fine powder. Sensory analysis indicated that acceptability of all types of ginger powders were in the range of 'liked very much' to 'liked moderately' by the panelists. The mean score obtained for colour was higher in shade dried ginger powder i.e., 8.20 as compared to oven dried (7.60), solar dried (7.70) and microwave dried ginger powder (7.80). Moisture content ranged from 3.55 % in solar dried ginger powder to 3.78 % in shade dried ginger powder. Slightly higher moisture content was found in shade dried ginger powder. Protein, crude fiber, fat and ash contents ranged from 5.02 to 5.82, 4.97 to 5.61, 0.76 to 0.90 and 3.38 to 3.66 %, respectively. β-carotene and ascorbic acid content was found maximum in shade dried ginger powder i.e., 0.81 mg/100 g and 3.83 mg/100 g, respectively. Polyphenol content was almost similar in all the samples whereas calcium was slightly higher in the shade dried ginger powder i.e., 69.21 mg/100 g. Results have shown that ginger powder prepared from various drying methods had good sensory and nutritional profile.

  8. Powder detergents production plant

    OpenAIRE

    Stanković Mirjana S.; Pezo Lato L.

    2003-01-01

    The IGPC Engineering Department designed basic projects for powder detergent production plant, using technology developed in the IGPC laboratories, in 1998. - 2000. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, a production plant with a capacity of 25,000 t/y was manufactured, at "Delta In", Zrenjanin, in 2000.This technology was an innovation, because new approach in mixing a powder materials was used, as well as introducing ...

  9. Determination of mode-I cohesive strength for interfaces

    DEFF Research Database (Denmark)

    Jørgensen, J. B.; Thouless, M. D.; Sørensen, Bent F.

    2016-01-01

    The cohesive strength is one of the governing parameters controlling crack deflection at interfaces, but measuring its magnitude is challenging. In this paper, we demonstrate a novel approach to determine the mode-I cohesive strength of an interface by using a 4-point single-edge-notch beam...... in response to this stress, before the main crack starts to grow. Observations using 2D digital-image correlation showed that an ''apparent" strain across the interface initially increases linearly with the applied load, but becomes nonlinear upon the initiation of the interface crack. The cohesive strength...

  10. On the application of cohesive crack modeling in cementitious materials

    DEFF Research Database (Denmark)

    Stang, Henrik; Olesen, John Forbes; Poulsen, Peter Noe;

    2007-01-01

    Cohesive crack models-in particular the Fictitious Crack Model - are applied routinely in the analysis of crack propagation in concrete and mortar. Bridged crack models-where cohesive stresses are assumed to exist together with a stress singularity at the crack tip-on the other hand, are used....... Further, a quantitative condition is established indicating when a bridged crack model can be approximated with a cohesive crack model with smooth crack closure in terms of the ratio between the energy dissipation associated with the crack tip and the process zone....

  11. Determination of mode-I cohesive strength for interfaces

    DEFF Research Database (Denmark)

    Jørgensen, J. B.; Thouless, M. D.; Sørensen, Bent F.

    2016-01-01

    The cohesive strength is one of the governing parameters controlling crack deflection at interfaces, but measuring its magnitude is challenging. In this paper, we demonstrate a novel approach to determine the mode-I cohesive strength of an interface by using a 4-point single-edge-notch beam...... in response to this stress, before the main crack starts to grow. Observations using 2D digital-image correlation showed that an ''apparent" strain across the interface initially increases linearly with the applied load, but becomes nonlinear upon the initiation of the interface crack. The cohesive strength...

  12. Flowers in flour: avalanches in cohesive granular matter.

    Science.gov (United States)

    Freyssingeas, E; Dalbe, M-J; Géminard, J-C

    2011-05-01

    We report on the intermittent dynamics of the free surface of a cohesive granular material during a silo discharge. In absence of cohesion, one observes the formation and the growth of a conical crater whose angle is well defined and constant in time. When the cohesion is involved the free surface exhibits a complex dynamics and the crater, resulting from a series of individual avalanches, is no longer axisymmetric. However, in spite of the intermittent behavior of the free surface, the flow rate is observed to remain constant throughout the discharge.

  13. Effect of contamination of pharmaceutical equipment on powder triboelectrification.

    Science.gov (United States)

    Eilbeck, J; Rowley, G; Carter, P A; Fletcher, E J

    2000-02-15

    Triboelectrification of pharmaceutical powders may cause problems during processing and manufacture due to adhesion/cohesion effects. The aim of this work was to investigate the role of adhered particles and moisture as contact surface contaminants on the electrostatic charging of size fractionated lactose, following contact with a surface, i.e. stainless steel, typically used in pharmaceutical process and manufacturing operations. Replicated experimental runs without cleaning the contact surface showed a successive decrease in the net electronegative charge due to adhered lactose particles. Removal of these contaminating particles by different cleaning methods had a considerable effect on the charge after triboelectrification. The charge on the lactose samples was found to decrease when humidity in the cyclone apparatus was increased from 2 to 100% relative humidity. These results clearly demonstrate that moisture, particulate contamination and method of cleaning of processing equipment during pharmaceutical manufacturing operations may influence the electrostatic behaviour of powders.

  14. Magnetically responsive enzyme powders

    Energy Technology Data Exchange (ETDEWEB)

    Pospiskova, Kristyna, E-mail: kristyna.pospiskova@upol.cz [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Safarik, Ivo, E-mail: ivosaf@yahoo.com [Regional Centre of Advanced Technologies and Materials, Palacky University, Slechtitelu 11, 783 71 Olomouc (Czech Republic); Department of Nanobiotechnology, Institute of Nanobiology and Structural Biology of GCRC, Na Sadkach 7, 370 05 Ceske Budejovice (Czech Republic)

    2015-04-15

    Powdered enzymes were transformed into their insoluble magnetic derivatives retaining their catalytic activity. Enzyme powders (e.g., trypsin and lipase) were suspended in various liquid media not allowing their solubilization (e.g., saturated ammonium sulfate and highly concentrated polyethylene glycol solutions, ethanol, methanol, 2-propanol) and subsequently cross-linked with glutaraldehyde. Magnetic modification was successfully performed at low temperature in a freezer (−20 °C) using magnetic iron oxides nano- and microparticles prepared by microwave-assisted synthesis from ferrous sulfate. Magnetized cross-linked enzyme powders were stable at least for two months in water suspension without leakage of fixed magnetic particles. Operational stability of magnetically responsive enzymes during eight repeated reaction cycles was generally without loss of enzyme activity. Separation of magnetically modified cross-linked powdered enzymes from reaction mixtures was significantly simplified due to their magnetic properties. - Highlights: • Cross-linked enzyme powders were prepared in various liquid media. • Insoluble enzymes were magnetized using iron oxides particles. • Magnetic iron oxides particles were prepared by microwave-assisted synthesis. • Magnetic modification was performed under low (freezing) temperature. • Cross-linked powdered trypsin and lipase can be used repeatedly for reaction.

  15. Manufacture of Fine-Pored Ceramics by the Gelcasting Method

    Directory of Open Access Journals (Sweden)

    Bronisław Psiuk

    2017-01-01

    Full Text Available The fine-pored materials represent a wide range of applications and searches are being continued to develop methods of their manufacturing. In the article, based on measurements on fine-grained powders of Al2O3, TiO2, and SiO2, it has been demonstrated that gelcasting can be relatively simple method of obtaining of nanoporous materials with high values of both specific surface area and open porosity. The powders were dispersed in silica sol, and the gelling initiator was NH4Cl. The usefulness of experiment design theory for developing of fine-pored materials with high porosity and specific surface area was also shown.

  16. Evidence for cohesive dispersal in the sea.

    Directory of Open Access Journals (Sweden)

    Ofer Ben-Tzvi

    Full Text Available As with many marine species, the vast majority of coral-reef fishes have a bipartite life cycle consisting of a dispersive larval stage and a benthic adult stage. While the potentially far-reaching demographic and ecological consequences of marine dispersal are widely appreciated, little is known of the structure of the larval pool and of the dispersive process itself. Utilizing Palindrome Sequence Analysis of otolith micro-chemistry (PaSA; we show that larvae of Neopomacentrus miryae (Pomacentridae appear to remain in cohesive cohorts throughout their entire pelagic larval duration (PLD; ~28 days. Genetically, we found cohort members to be maternally (mtDNA unrelated. While physical forcing cannot be negated as contributing to initial cohort formation, the small scale of the observed spatial structure suggests that some behavioral modification may be involved from a very early age. This study contributes to our ongoing re-evaluation of the processes that structure marine populations and communities and the spatial scales at which they operate.

  17. Recycling high density tungsten alloy powder by oxidization-reduction process

    Institute of Scientific and Technical Information of China (English)

    张兆森; 陈立宝; 贺跃辉; 黄伯云

    2002-01-01

    The processes of directly recycling high density tungsten alloy by oxidation-reduction technique were investigated. The particle size of recycled powder is fine, and the shape of powder particle is regular when the final reduction temperature is 850℃, in which the average size of the tungsten alloy particles reduced is about 1.5μm. The average size of the alloy particles increase to 6μm and 9μm when increasing the reduction temperature to 900℃ and 950℃, respectively. However, if the reduction temperature is higher than 900℃, the surface feature of powder is complicated. Increasing reduction temperature from 900℃ to 950℃, the content of oxygen of recycled powder decreases from 0.2314% to 0.1700%, and powder particles grow slightly. It has been also found that the chemical composition of the recycled alloy powder is the same as the initial powder.

  18. Student leadership and advocacy for social cohesion: A South ...

    African Journals Online (AJOL)

    they commit themselves to a cause: in this case, a social cohesion vision.5. Following this ..... were soon going to create a Frankenstein's Monster manifesting in crime, ..... Dangerous others, insecure societies, fear and social division. Farnham ...

  19. Effect of cohesive force on the formation of a sandpile

    Science.gov (United States)

    Dong, K. J.; Zou, R. P.; Chu, K. W.; Yang, R. Y.; Yu, A. B.; Hu, D. S.

    2013-06-01

    This paper presents a numerical study on the piling processes of mono-sized wet particles by the discrete element method (DEM). The capillary force between particles due to liquid bridge is implemented in an existing DEM model. The effects of moisture content on the repose angle and structure of a pile are studied by a series of controlled numerical experiments. It is confirmed that the structure of a pile is similar to that of a packing for cohesive particles. Moreover, the averaged local porosity and repose angle have similar changes with the moisture content and can be linearly correlated. Therefore, the relationship between the repose angle and the cohesive force can be established based on the previous correlation between the porosity and the force ratio of the cohesive force to gravity developed in the packing of cohesive particles.

  20. Tracking cohesive subgroups over time in inferred social networks

    Science.gov (United States)

    Chin, Alvin; Chignell, Mark; Wang, Hao

    2010-04-01

    As a first step in the development of community trackers for large-scale online interaction, this paper shows how cohesive subgroup analysis using the Social Cohesion Analysis of Networks (SCAN; Chin and Chignell 2008) and Data-Intensive Socially Similar Evolving Community Tracker (DISSECT; Chin and Chignell 2010) methods can be applied to the problem of identifying cohesive subgroups and tracking them over time. Three case studies are reported, and the findings are used to evaluate how well the SCAN and DISSECT methods work for different types of data. In the largest of the case studies, variations in temporal cohesiveness are identified across a set of subgroups extracted from the inferred social network. Further modifications to the DISSECT methodology are suggested based on the results obtained. The paper concludes with recommendations concerning further research that would be beneficial in addressing the community tracking problem for online data.

  1. Collectivism, Individualism, and Cohesion in a Team-based Occupation.

    Science.gov (United States)

    Workman, Michael

    2001-01-01

    Ethnographic interviews with 3 teams of 26 computer programmers revealed how levels of collectivism or individualism differed as groups solved problems. Cultural cohesion was identified as a separate construct from collectivism. (Contains 53 references.) (SK)

  2. COHESIVE ZONE FINITE ELEMENT-BASED MODELING OF HYDRAULIC FRACTURES

    Institute of Scientific and Technical Information of China (English)

    Zuorong Chen; A.P. Bunger; Xi Zhang; Robert G. Jeffrey

    2009-01-01

    Hydraulic fracturing is a powerful technology used to stimulate fluid production from reservoirs. The fully 3-D numerical simulation of the hydraulic fracturing process is of great importance to the efficient application of this technology, but is also a great challenge because of the strong nonlinear coupling between the viscous flow of fluid and fracture propagation. By taking advantage of a cohesive zone method to simulate the fracture process, a finite element model based on the existing pore pressure cohesive finite elements has been established to investigate the propagation of a penny-shaped hydraulic fracture in an infinite elastic medium. The effect of cohesive material parameters and fluid viscosity on the hydraulic fracture behaviour has been investigated. Excellent agreement between the finite element results and analytical solutions for the limiting case where the fracture process is dominated by rock fracture toughness demonstrates the ability of the cohesive zone finite element model in simulating the hydraulic fracture growth for this case.

  3. On the Cohesion of English Entertainment News Discourse

    Institute of Scientific and Technical Information of China (English)

    XU Wen

    2013-01-01

    With the rapid development of entertainment news, entertainment news has gained more and more attention in recent years. While previous studies have been mainly conducted from the perspective of journalism, the present study focuses on the co-hesion strategies of the selected news discourse from the linguistic point of view. Cohesion is an important linguistic concept pro-posed by Halliday. This paper will analyze the news discourse from China Daily quantitatively and qualitatively. It is found that in the entertainment news discourse grammatical cohesive devices are commonly used. The present study attempts to analyze the co-hesive features of English entertainment news, so as to help readers improve the efficiency in English news reading.

  4. ANALYSIS ON THE COHESIVE STRESS AT HALF INFINITE CRACK TIP

    Institute of Scientific and Technical Information of China (English)

    王利民; 徐世烺

    2003-01-01

    The nonlinear fracture behavior of quasi-brittle materials is closely related with the cohesive force distribution of fracture process zone at crack tip. Based on fracture character of quasi-brittle materials, a mechanical analysis model of half infinite crack with cohesive stress is presented. A pair of integral equations is established according to the superposition principle of crack opening displacement in solids, and the fictitious adhesive stress is unknown function. The properties of integral equations are analyzed, and the series function expression of cohesive stress is certified. By means of the data of actual crack opening displacement, two approaches to gain the cohesive stress distribution are proposed through resolving algebra equation. They are the integral transformation method for continuous displacement of actual crack opening, and the least square method for the discrete data of crack opening displacement. The calculation examples of two approaches and associated discussions are given.

  5. Student leadership and advocacy for social cohesion: A South ...

    African Journals Online (AJOL)

    in higher education in South Africa to act as advocates for social cohesion, ... confirms two issues, namely, group solidarity and the on-going nature of ..... now goes beyond race and ethnicity and covers gender, sexuality, physical challenges ...

  6. Stress and strain rate analysis of the FT4 Powder Rheometer

    Directory of Open Access Journals (Sweden)

    Hare Colin

    2017-01-01

    Full Text Available The Freeman FT4 Powder Rheometer has been reported to describe well the powder flow behaviour in instances where other techniques fail. We use DEM to simulate the FT4 operation for slightly cohesive large glass beads at a range of strain rates. The curved impeller is shown to be beneficial in comparison to a flat blade as the variation of shear stress across the blade is reduced. The shear stress in front of the blade correlates well with flow energy (which the device measures for a range of tip speeds and is shown to increase approximately linearly with tip speed when operating beyond the quasi-static regime.

  7. An Assessment of Work Group Cohesion and Productivity.

    Science.gov (United States)

    1986-09-01

    Perspective. MS thesis. Administrative Science Department, Naval Postgraduate School, Monterey CA, June 1983 (AD-A128047). Cartwright , Dorwin and Alvin...work group. The size of a group may have a moderating influence on those variables that affect cohesion ( Cartwright and Zander, 1968). If group size has...industrial work groups (Seashore, 1954). Cartwright and Zander, in their review of studies relating similarities and group cohesion, stated that dis

  8. The Relation between Sociometric Choices and Group Cohesion

    Science.gov (United States)

    2006-11-01

    criteria covering performance, attitudinal, and behavioral outcomes. 15. SUBJECT TERMS cohesion, sociometry , peer bonding, leader bonding, unit performance...CHOICES AND GROUP COHESION EXECUTIVE SUMMARY Research Requirement: Because of the difficulties and limitations of using sociometry , previous research has...and Dissemination of Findings: Sociometry can be used as a method for estimating the quality of group dynamics in a squad or a platoon. Generally, the

  9. Barossa Night: cohesion in the British Army officer corps.

    Science.gov (United States)

    Bury, Patrick

    2017-06-01

    Contrasting the classical explanation of military group cohesion as sustained by interpersonal bonds, recent scholars have highlighted the importance of ritualized communication, training and drills in explaining effective military performance in professional armies. While this has offered a welcome addition to the cohesion literature and a novel micro-sociological method of examining cohesion, its primary evidential base has been combat groups. Indeed, despite their prominent role in directing operations over the past decade, the British Army's officer corps has received relatively little attention from sociologists during this period. No attempt has been made to explain cohesion in the officer corps. Using a similar method to recent cohesion scholars, this paper seeks to address this imbalance by undertaking a micro-sociology of one ritual in particular: 'Barossa Night' in the Royal Irish Regiment. Firstly, it draws on the work of Durkheim to examine how cohesion amongst the officer corps is created and sustained through a dense array of practises during formal social rituals. It provides evidence that the use of rituals highlights that social solidarity is central to understanding officer cohesion. Secondly, following Hockey's work on how private soldiers negotiate order, the paper shows how this solidarity in the officer corps is based on a degree of negotiated order and the need to release organizational tensions inherent in a strictly hierarchical rank structure. It highlights how the awarding of gallantry medals can threaten this negotiated order and fuel deviancy. In examining this behaviour, the paper shows that even amongst an officer class traditionally viewed as the elite upholders of organizational discipline, the negotiation of rank and hierarchy can be fluid. How deviant behaviour is later accepted and normalized by senior officers indicates that negotiated order is as important to understanding cohesion in the British Army's officer corps as it is

  10. The Process Architecture of EU Territorial Cohesion Policy

    OpenAIRE

    Andreas Faludi

    2010-01-01

    When preparing the European Spatial Development Perspective (ESDP), Member States were supported by the European Commission but denied the EU a competence in the matter. Currently, the Treaty of Lisbon identifies territorial cohesion as a competence shared between the Union and the Member States. This paper is about the process architecture of territorial cohesion policy. In the past, this architecture resembled the Open Method of Coordination (OMC) which the White Paper on European Governanc...

  11. Utilization of Large Cohesive Interface Elements for Delamination Simulation

    DEFF Research Database (Denmark)

    Bak, Brian Lau Verndal; Lund, Erik

    2012-01-01

    This paper describes the difficulties of utilizing large interface elements in delamination simulation. Solutions to increase the size of applicable interface elements are described and cover numerical integration of the element and modifications of the cohesive law.......This paper describes the difficulties of utilizing large interface elements in delamination simulation. Solutions to increase the size of applicable interface elements are described and cover numerical integration of the element and modifications of the cohesive law....

  12. THE COHESIVE NATURE OF THE LATE RAMESSIDE LETTERS

    Institute of Scientific and Technical Information of China (English)

    Kim; Ridealgh

    2014-01-01

    <正>1.Introduction When addressing language cohesion,an attempt must be made to identify how language is used to create cohesive and coherent communication,or how one utterance follows another.William Labov describes the task at hand,stating that‘the fundamental problem of discourse analysis1is to show how one utterance follows another in a rational,rule governed manner—in other words,how we

  13. Study on Lexical Cohesion in English-Chinese and its Implications for Translation

    Institute of Scientific and Technical Information of China (English)

    孙菁; 李媛媛

    2014-01-01

    Lexical cohesion is one of the major cohesive devices. Based on the the theoretical framework proposed by Halliday and Hasan (2001), This paper tentatively compares lexical cohesion in English and Chinese, analyzes the similarities and differences of cohesive devices in English and Chinese and sheds a new light for learners upon Chinese-English and English-Chinese translation.

  14. Kinetic energy density and agglomerate abrasion rate during blending of agglomerates into powders.

    Science.gov (United States)

    Willemsz, Tofan A; Hooijmaijers, Ricardo; Rubingh, Carina M; Tran, Thanh N; Frijlink, Henderik W; Vromans, Herman; van der Voort Maarschalk, Kees

    2012-01-23

    Problems related to the blending of a cohesive powder with a free flowing bulk powder are frequently encountered in the pharmaceutical industry. The cohesive powder often forms lumps or agglomerates which are not dispersed during the mixing process and are therefore detrimental to blend uniformity. Achieving sufficient blend uniformity requires that the blending conditions are able to break up agglomerates, which is often an abrasion process. This study was based on the assumption that the abrasion rate of agglomerates determines the required blending time. It is shown that the kinetic energy density of the moving powder bed is a relevant parameter which correlates with the abrasion rate of agglomerates. However, aspects related to the strength of agglomerates should also be considered. For this reason the Stokes abrasion number (St(Abr)) has been defined. This parameter describes the ratio between the kinetic energy density of the moving powder bed and the work of fracture of the agglomerate. The St(Abr) number is shown to predict the abrasion potential of agglomerates in the dry-mixing process. It appeared possible to include effects of filler particle size and impeller rotational rate into this concept. A clear relationship between abrasion rate of agglomerates and the value of St(Abr) was demonstrated. Copyright © 2011 Elsevier B.V. All rights reserved.

  15. Substitution as a Device of Grammatical Cohesion in English Contexts

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Hasannejad

    2012-05-01

    Full Text Available The present study set out to investigate the effect of teaching substitution as a kind of grammatical cohesion on the true identification of confusing substitution elements with cohesive or non-cohesive roles in different contexts and also the production of modal, reporting and conditional contexts through clausal substitution acquaintance. To this end, the following procedures were taken. First 120 male and female EFL students were selected from Iranshahr Azad University. Having administered the language proficiency test, researchers selected 80 students as intermediate subjects according to their TOEFL band scores. First, pretests of cohesion identification (substitution and production of modal, reporting and conditional environments were administered to both control and experimental groups. Then, the experimental group was exposed to the teaching of the above-said above-mentioned cohesive device. Finally, post-tests of substitution elements’ identification and modal, reporting and conditional contexts’ production through clausal substitution familiarity were administered. The results showed that cohesive device treatment helped students on the true identification of substitution elements. Another finding proved that EFL students might have no difficulty in learning certain rules or classification of rules and application of their clausal substitution knowledge in creating modal, reporting and conditional contexts. Our findings can have implications for the field of language learning and teaching.

  16. Determinants of Sir2-Mediated, Silent Chromatin Cohesion.

    Science.gov (United States)

    Chen, Yu-Fan; Chou, Chia-Ching; Gartenberg, Marc R

    2016-08-01

    Cohesin associates with distinct sites on chromosomes to mediate sister chromatid cohesion. Single cohesin complexes are thought to bind by encircling both sister chromatids in a topological embrace. Transcriptionally repressed chromosomal domains in the yeast Saccharomyces cerevisiae represent specialized sites of cohesion where cohesin binds silent chromatin in a Sir2-dependent fashion. In this study, we investigated the molecular basis for Sir2-mediated cohesion. We identified a cluster of charged surface residues of Sir2, collectively termed the EKDK motif, that are required for cohesin function. In addition, we demonstrated that Esc8, a Sir2-interacting factor, is also required for silent chromatin cohesion. Esc8 was previously shown to associate with Isw1, the enzymatic core of ISW1 chromatin remodelers, to form a variant of the ISW1a chromatin remodeling complex. When ESC8 was deleted or the EKDK motif was mutated, cohesin binding at silenced chromatin domains persisted but cohesion of the domains was abolished. The data are not consistent with cohesin embracing both sister chromatids within silent chromatin domains. Transcriptional silencing remains largely intact in strains lacking ESC8 or bearing EKDK mutations, indicating that silencing and cohesion are separable functions of Sir2 and silent chromatin.

  17. Sororin actively maintains sister chromatid cohesion.

    Science.gov (United States)

    Ladurner, Rene; Kreidl, Emanuel; Ivanov, Miroslav P; Ekker, Heinz; Idarraga-Amado, Maria Helena; Busslinger, Georg A; Wutz, Gordana; Cisneros, David A; Peters, Jan-Michael

    2016-03-15

    Cohesion between sister chromatids is established during DNA replication but needs to be maintained to enable proper chromosome-spindle attachments in mitosis or meiosis. Cohesion is mediated by cohesin, but also depends on cohesin acetylation and sororin. Sororin contributes to cohesion by stabilizing cohesin on DNA. Sororin achieves this by inhibiting WAPL, which otherwise releases cohesin from DNA and destroys cohesion. Here we describe mouse models which enable the controlled depletion of sororin by gene deletion or auxin-induced degradation. We show that sororin is essential for embryonic development, cohesion maintenance, and proper chromosome segregation. We further show that the acetyltransferases ESCO1 and ESCO2 are essential for stabilizing cohesin on chromatin, that their only function in this process is to acetylate cohesin's SMC3 subunit, and that DNA replication is also required for stable cohesin-chromatin interactions. Unexpectedly, we find that sororin interacts dynamically with the cohesin complexes it stabilizes. This implies that sororin recruitment to cohesin does not depend on the DNA replication machinery or process itself, but on a property that cohesin acquires during cohesion establishment.

  18. SHUGOSHINs and PATRONUS protect meiotic centromere cohesion in Arabidopsis thaliana.

    Science.gov (United States)

    Zamariola, Linda; De Storme, Nico; Vannerum, Katrijn; Vandepoele, Klaas; Armstrong, Susan J; Franklin, F Christopher H; Geelen, Danny

    2014-03-01

    In meiosis, chromosome cohesion is maintained by the cohesin complex, which is released in a two-step manner. At meiosis I, the meiosis-specific cohesin subunit Rec8 is cleaved by the protease Separase along chromosome arms, allowing homologous chromosome segregation. Next, in meiosis II, cleavage of the remaining centromere cohesin results in separation of the sister chromatids. In eukaryotes, protection of centromeric cohesion in meiosis I is mediated by SHUGOSHINs (SGOs). The Arabidopsis genome contains two SGO homologs. Here we demonstrate that Atsgo1 mutants show a premature loss of cohesion of sister chromatid centromeres at anaphase I and that AtSGO2 partially rescues this loss of cohesion. In addition to SGOs, we characterize PATRONUS which is specifically required for the maintenance of cohesion of sister chromatid centromeres in meiosis II. In contrast to the Atsgo1 Atsgo2 double mutant, patronus T-DNA insertion mutants only display loss of sister chromatid cohesion after meiosis I, and additionally show disorganized spindles, resulting in defects in chromosome segregation in meiosis. This leads to reduced fertility and aneuploid offspring. Furthermore, we detect aneuploidy in sporophytic tissue, indicating a role for PATRONUS in chromosome segregation in somatic cells. Thus, ploidy stability is preserved in Arabidopsis by PATRONUS during both meiosis and mitosis.

  19. Demythologising social cohesion: Towards a practical theological vision

    Directory of Open Access Journals (Sweden)

    Stephanus F. de Beer

    2014-08-01

    Full Text Available This article considers the topical issue of social cohesion. It seeks to demythologise the issuebringing it into critical conversation with eight related categories. It proposes that a vision ofa socially cohesive society should employ all eight categories as parallel and complementarystrategies. Secondly, it proposes a practical theological vision of social cohesion that will notonly embrace these eight categories but will root itself in a spirituality of the table, informedby a vision of the oikos of God, seeking shalom in the oikos and doing so through four strategicmoments of engagement.Intradisciplinary and/or interdisciplinary implications: This article indicates that socialcohesion requires an integrated approach of different strategies, not competing butcomplementing each other. Social cohesion requires interdisciplinary, intradisciplinary andtransdisciplinary research and action. For example, exploring ways in which land redistributioninhibits or contributes to social cohesion requires multiple stakeholders and disciplinesdiscerning together. The proposed practical theological vision implies new categories to beincluded in curricula and practical theological discourse for it to contribute meaningfully notonly to the current debate but also to practices fostering a socially cohesive society.

  20. Device for preparing combinatorial libraries in powder metallurgy.

    Science.gov (United States)

    Yang, Shoufeng; Evans, Julian R G

    2004-01-01

    This paper describes a powder-metering, -mixing, and -dispensing mechanism that can be used as a method for producing large numbers of samples for metallurgical evaluation or electrical or mechanical testing from multicomponent metal and cermet powder systems. It is designed to make use of the same commercial powders that are used in powder metallurgy and, therefore, to produce samples that are faithful to the microstructure of finished products. The particle assemblies produced by the device could be consolidated by die pressing, isostatic pressing, laser sintering, or direct melting. The powder metering valve provides both on/off and flow rate control of dry powders in open capillaries using acoustic vibration. The valve is simple and involves no relative movement, avoiding seizure with fine powders. An orchestra of such valves can be arranged on a building platform to prepare multicomponent combinatorial libraries. As with many combinatorial devices, identification and evaluation of sources of mixing error as a function of sample size is mandatory. Such an analysis is presented.

  1. Sinterability and microstructure evolution during sintering of ferrous powder mixtures

    Directory of Open Access Journals (Sweden)

    Kétner Bendo Demétrio

    2013-01-01

    Full Text Available The present work is focused on ferrous powder metallurgy and presents some results of a development of a suitable masteralloy for use as an additive to iron powder for the production of sintered steels. The masteralloy was produced by melting a powder mixture containing approximately Fe + 20% Ni + 20% Mn + 20% Si + 1% C (wt%, in order to obtain a cast billet that was converted into fine powder by crushing and milling. It was observed presence of SiC in the masteralloy after melting that is undesirable in the alloy. Si element should be introduced by using ferrosilicon. Sintered alloys with distinct contents of alloying elements were prepared by mixing the masteralloy powder to plain iron powder. Samples were produced by die compaction of the powder mixtures and sintering at 1200 °C in a differential dilatometer in order to record their linear dimensional behaviour during heating up and isothermal sintering, aiming at studying the sinterability of the compacts. Microstructure development during sintering was studied by SEM, XRD and microprobe analyses.

  2. Characterization of Cu{sub 6}Sn{sub 5} intermetallic powders produced by water atomization and powder heat treatment

    Energy Technology Data Exchange (ETDEWEB)

    Tongsri, Ruangdaj, E-mail: ruangdt@mtec.or.th [Powder Metallurgy Research and Development Unit (PM-RDU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Yotkaew, Thanyaporn, E-mail: thanyy@mtec.or.th [Powder Metallurgy Research and Development Unit (PM-RDU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Krataitong, Rungtip, E-mail: rungtipk@mtec.or.th [Powder Metallurgy Research and Development Unit (PM-RDU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Wila, Pongsak, E-mail: pongsakw@mtec.or.th [Powder Metallurgy Research and Development Unit (PM-RDU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Sir-on, Autcharaporn, E-mail: autchars@mtec.or.th [Materials Characterization Research Unit (MCRU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Muthitamongkol, Pennapa, E-mail: pennapm@mtec.or.th [Materials Characterization Research Unit (MCRU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand); Tosangthum, Nattaya, E-mail: nattayt@mtec.or.th [Powder Metallurgy Research and Development Unit (PM-RDU), National Metal and Materials Technology Center, 114 Paholyothin, Klong 1, Klong Luang, Pathum Thani 12120 (Thailand)

    2013-12-15

    Since the Cu{sub 6}Sn{sub 5} intermetallic shows its importance in industrial applications, the Cu{sub 6}Sn{sub 5} intermetallic-containing powders, produced by a powder processing route with a high production rate, were characterized. The route consisted of water atomization of an alloy melt (Cu–61 wt.% Sn) and subsequent heat treatment of the water-atomized powders. Characterization of the water-atomized powders and their heated forms was conducted by using X-ray diffraction, scanning electron microscopy and transmission electron microscopy. Fine water-atomized powder microstructures consisted of primary hexagonal η-Cu{sub 6.25}Sn{sub 5} dendrites coexisting with interdendritic η-Cu{sub 6.25}Sn{sub 5} + β-Sn eutectic. Solidification of fine melt droplets was governed by surface nucleation and growth of the primary hexagonal η-Cu{sub 6.25}Sn{sub 5} dendrites followed by η-Cu{sub 6.25}Sn{sub 5} + β-Sn eutectic solidification of the remnant liquid. In coarse melt droplets, nucleation and growth of primary ε-Cu{sub 3}Sn dendrites were followed by peritectic reaction (ε-Cu{sub 3}Sn + liquid → η-Cu{sub 6.25}Sn{sub 5}) or direct crystallization of η-Cu{sub 6.25}Sn{sub 5} phase from the undercooled melt. Finally, the η-Cu{sub 6.25}Sn{sub 5} + β-Sn eutectic solidification of the remnant liquid occurred. Heating of the water-atomized powders at different temperatures resulted in microstructural homogenization. The water-atomized powders with mixed phases were transformed to powders with single monoclinic ή-Cu{sub 6}Sn{sub 5} phase. - Highlights: • The Cu{sub 6}Sn{sub 5} intermetallic powder production route was proposed. • Single phase Cu{sub 6}Sn{sub 5} powders could be by water atomization and heating. • Water-atomized Cu–Sn powders contained mixed Cu–Sn phases. • Solidification and heat treatment of water-atomized Cu–Sn powders are explained.

  3. Cow dung powder poisoning

    OpenAIRE

    Khaja Mohideen Sherfudeen; Senthil Kumar Kaliannan; Pavan Kumar Dammalapati

    2015-01-01

    Cow dung, which has germicidal property, was used in ancient days to clean living premises in South India. Nowadays, people are using commercially available synthetic cow dung powder. It is locally known as “saani powder” in Tamil Nadu. It is freely available in homes and is sometimes accidentally consumed by children. It is available in two colors - yellow and green. Cow dung powder poisoning is common in districts of Tamil Nadu such as Coimbatore, Tirupur, and Erode. We report two cases of ...

  4. Study of Delamination and Buckling of Paper during the Creping Process using Finite Element Method -- A Cohesive Element Approach

    Science.gov (United States)

    Gupta, Swapnil Sheelkumar

    Paper variants such as paper napkins, tissue paper are manufactured by a process called as creping during which a paper adhesively bonded to a rotating drum is continuously scraped off by a blade. Resulting low density paper provides critical attributes such as fluid absorbency, softness, and stretchiness to the final paper product. The macroscopic effect of creping is the formation of fine ridges called as " crepes". The quality of the final product is characterized by the length of the crepes. The process of creping has been hypothesized to be a periodic sequence of delamination, buckling and post-buckling compression of paper. A quasi-static comparison of a two dimensional finite element model implementing surface based cohesive zone theory and a critical stress criteria based fracture model is presented. The adhesive being a critical part of creping is represented by a zero thickness cohesive layer in the cohesive model . A comparison of a 1-D analytical model implementing an energy release rate approach and a Virtual Crack Closure Technique (VCCT) quasi-static finite element model is presented. An experimental investigation to quantitatively determine the adhesive fracture toughness during creping is conducted by an energy based approach. The influence of drum speed and adhesive concentration on the adhesive fracture energy is analyzed and comparison with a dynamic finite element model is obtained.

  5. Investigation into the influence of primary crystallization conditions on the mechanical properties and secondary processing behaviour of fluticasone propionate for carrier based dry powder inhaler formulations.

    Science.gov (United States)

    Kubavat, Harshal A; Shur, Jagdeep; Ruecroft, Graham; Hipkiss, David; Price, Robert

    2012-04-01

    To investigate the influence of primary crystallization conditions on the mechanical properties and secondary processing behaviour of fluticasone propionate (FP) for carrier based dry powder inhaler (DPI) formulations. Young's modulus of FP crystals produced using different anti-solvents was determined using nanoindentation. Physicochemical and surface interfacial properties via the cohesive-adhesive balance (CAB) approach to colloid probe atomic force microscopy (AFM) of air-jet micronised FP crystals were investigated. These data were correlated to in vitro aerosolization performance of binary and combination DPI formulations containing salmeterol xinafoate (SX). Young's modulus of FP crystals produced using different anti-solvents ranged from 0.6-12.4 GPa. Crystals with low Young's modulus required multiple passes in the microniser to reduce the particle size to less than 5 μm, whilst those with the highest Young's modulus required a single pass. CAB of micronized FP samples was similar with respect to lactose, however, their adhesive affinity to SX varied. Samples of FP with greatest adhesion to SX produced greater fine particle delivery of SX in combination DPI formulations. Crystallisation conditions may affect the mechanical properties of FP, and therefore secondary processing of the material and their interfacial properties and product performance in carrier based DPI formulations.

  6. Fine Arts Database (FAD)

    Data.gov (United States)

    General Services Administration — The Fine Arts Database records information on federally owned art in the control of the GSA; this includes the location, current condition and information on artists.

  7. Fine Needle Aspiration

    Science.gov (United States)

    ... FNA), also called fine needle biopsy, is a type of biopsy that can be used to diagnose many types ... in which case another FNA or a different type of biopsy procedure may needed. Because the needle is so ...

  8. Analyses of fine paste ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Sabloff, J A [ed.

    1980-01-01

    Four chapters are included: history of Brookhaven fine paste ceramics project, chemical and mathematical procedures employed in Mayan fine paste ceramics project, and compositional and archaeological perspectives on the Mayan fine paste ceramics. (DLC)

  9. Physical properties and bioactive constituents of powdered mixtures and drinks prepared with cocoa and various sweeteners.

    Science.gov (United States)

    Belscak-Cvitanović, Ana; Benković, Maja; Komes, Drazenka; Bauman, Ingrid; Horzić, Dunja; Dujmić, Filip; Matijasec, Matea

    2010-06-23

    In the present study the physical properties of powdered cocoa drink mixtures prepared from two cocoa powders with various fat contents and different sweeteners, as well as the bioactive content and sensory properties of cocoa drinks prepared from them, were investigated. Particle size and bulk density of the used sugars and sweeteners, as well as the formulated mixtures, were determined and their influence on cohesion index was evaluated. To compare the content of polyphenols in the formulated cocoa drink mixtures, UV-vis spectrophotometric methods were applied. Antioxidant capacity of cocoa drinks was evaluated by using the 2,2-diphenyl-1-picrylhydrazyl (DPPH), 2,2'-azinobis(3-ethylbenzthiazoline-6-sulfonic acid) (ABTS), and ferric reducing/antioxidant power (FRAP) assays. The analyzed cocoa drinks prepared from cocoa powder and different sugars or sweeteners delivered a substantial content of cocoa antioxidants, whereas the content and the type of sugar or sweetener did not affect the polyphenolic constituents of the prepared cocoa mixtures. Cocoa powder mixtures prepared with the cocoa powder containing higher fat content (16-18%) generally provided lower total polyphenol, total flavonoid, flavan-3-ol, and proanthocyanidin contents, compared to the mixtures prepared with cocoa containing lower fat content (10-12%). Total phenol content of cocoa drinks prepared from experimental mixtures ranged from 320.45 to 480.45 mg of GAE/L, whereas the ranking of the antioxidant capacities varied depending on the used assay, and the fat content of cocoa powder did not affect the antioxidant capacity of cocoa mixtures. As determined, the addition of sugar to cocoa powder increases the solubility and dispersibility of the mixtures; on the basis of their cohesion index all mixtures can be classified as very cohesive or hardened/extremely cohesive. Results of the sensory evaluation, using the 9-point hedonic scale, showed that there was a preference for the cocoa drinks made

  10. Transport of reservoir fines

    DEFF Research Database (Denmark)

    Yuan, Hao; Shapiro, Alexander; Stenby, Erling Halfdan

    Modeling transport of reservoir fines is of great importance for evaluating the damage of production wells and infectivity decline. The conventional methodology accounts for neither the formation heterogeneity around the wells nor the reservoir fines’ heterogeneity. We have developed an integral...... dispersion equation in modeling the transport and the deposition of reservoir fines. It successfully predicts the unsymmetrical concentration profiles and the hyperexponential deposition in experiments....

  11. Seeing into the infrared: a novel IR fluorescent fingerprint powder.

    Science.gov (United States)

    King, Roberto S P; Hallett, Peter M; Foster, Doug

    2015-04-01

    A preliminary study demonstrates that latent fingermarks across a range of highly patterned, coloured non-porous and semi-porous substrates may be clearly developed and imaged in the near infrared following a simple dusting method using finely divided spirulina platensis powder, a naturally occurring, non-toxic algae, used widely within the food industry. Troublesome printed/multicoloured backgrounds show less interference with the fluorescence observed using this material, unlike conventional luminescent powders which fluoresce in the visible spectrum alongside the background to which they are applied. The material shows promise for use both in the field and in the laboratory.

  12. Electrostatic separation of mineral and vegetal powders with a custom built corona separator: application to biorefinery of rice husk

    Directory of Open Access Journals (Sweden)

    Rajaonarivony Rova Karine

    2017-01-01

    Full Text Available In a dry biorefinery scheme, the separation of plant materials into powders rich in the constituents of interest is a crucial step. In recent years, electrostatic separation of agri-resources has sparked a growing interest for its potentialities, but optimization efforts remain to be done especially in case of fine powders. In this study a custom-designed corona-electrostatic separator has been built and its usage for the separation of mineral (ash from rice husk and vegetal powders (cellulose fibers with different particle size distributions has been studied. First, the powders have been characterized by their electric charge decay curves and their behaviour on the separator was studied. At a second time, separation tests have been carried out with blends of these two powders, and with native, finely ground, rice husk powder (constituted of both mineral and vegetal particles. In each case, the efficiency of the process was evaluated.

  13. Electrostatic separation of mineral and vegetal powders with a custom built corona separator: application to biorefinery of rice husk

    Science.gov (United States)

    Rajaonarivony, Rova Karine; Rouau, Xavier; Dascalescu, Lucien; Mayer-Laigle, Claire

    2017-06-01

    In a dry biorefinery scheme, the separation of plant materials into powders rich in the constituents of interest is a crucial step. In recent years, electrostatic separation of agri-resources has sparked a growing interest for its potentialities, but optimization efforts remain to be done especially in case of fine powders. In this study a custom-designed corona-electrostatic separator has been built and its usage for the separation of mineral (ash from rice husk) and vegetal powders (cellulose fibers) with different particle size distributions has been studied. First, the powders have been characterized by their electric charge decay curves and their behaviour on the separator was studied. At a second time, separation tests have been carried out with blends of these two powders, and with native, finely ground, rice husk powder (constituted of both mineral and vegetal particles). In each case, the efficiency of the process was evaluated.

  14. Acculturative stress and diminishing family cohesion among recent Latino immigrants.

    Science.gov (United States)

    Dillon, Frank R; De La Rosa, Mario; Ibañez, Gladys E

    2013-06-01

    This study investigates a theorized link between Latino immigrants' experience of acculturative stress during their two initial years in the United States (US) and declines in family cohesion from pre- to post-immigration contexts. This retrospective cohort study included 405 adult participants. Baseline assessment occurred during participants' first 12 months in the US. Follow-up assessment occurred during participants' second year in the US. General linear mixed models were used to estimate change in family cohesion and sociocultural correlates of this change. Inverse associations were determined between acculturative stress during initial years in the US and declines in family cohesion from pre-immigration to post-immigration contexts. Participants with undocumented immigration status, those with lower education levels, and those without family in the US generally indicated lower family cohesion. Participants who experienced more acculturative stress and those without family in the US evidenced a greater decline in family cohesion. Results are promising in terms of implications for health services for recent Latino immigrants.

  15. Cohesion in News Articles: A Discourse Analysis Approach

    Directory of Open Access Journals (Sweden)

    Angelina Subrayan Michael

    2013-05-01

    Full Text Available Cohesion is deemed to be outside of the structure of text because structure in text is provided by grammar. The design of cohesion in text is connected to semantic ties or “relations of meanings that exist within the text, and that define it as a text” (Halliday and Hasan, 1976. The study discusses an analysis done on two Malaysian newspaper articles from the New Straits Times. The study investigates the discourses apparent in the texts and the methods in which discourses are represented through particular linguistic choices. The purpose of the study is to identify discourses that stand for universally held assumptions about how different texts are created and how these discourses signify connection of specific practices and/or encompass a policy for change. Halliday & Hasan (1976 convey texture to the method in which diverse fundamentals in a text are connected or attached jointly to shape a cohesive unity, which also conveys the fact that the texts express completely to the setting in which it is located. Both articles project several connections in the field, in the theme and in the method of writing which are reflected in their corresponding ritual of structural and lexico-grammatical resources.Keywords: cohesion, discourse analysis, reference, conjunction, lexical cohesion

  16. Environmental cohesion across the Hungarian-Croatian border

    Directory of Open Access Journals (Sweden)

    Varjú Viktor

    2016-01-01

    Full Text Available Environmental cohesion (as a new EU paradigm for a place-based interpretation of environmental justice has a clear connection to territorial cohesion. Based on this idea, advantages for people can include an equitable distribution of environmental protection and access to environmental services. In non-EU countries regional environmental cohesion is used as an instrument to accelerate accession to the EU and it may be manifested as a declaration of environmental diplomacy. Environmental cohesion across a border can be identified as soon as two regions - alongside the border - start to cooperate in order to improve environmental conditions and to ensure equal access to natural resources and environmental services. After a literature review environmental cohesion is evaluated in multidimensional way, using empirical quantitative and qualitative data and a two-pillar based methodological approach. The Croatian-Hungarian border area was closed for a long time. As a result, developments avoided the area, on the other, natural resources remained mainly untouched. However, the two countries have had different approaches towards the area, while, Croatia made efforts to build another water power plant, Hungary intended to preserve and extend a Natural Park. This contradiction remained until the accession process of Croatia. Finally the disagreement between the two countries was moderated by a UNESCO Biosphere Reserve that was created alongside the border in 2015. The post-2010 period has been characterised by an increasing number of environmental-related cooperations.

  17. Research on cohesive sediment erosion by flow: An overview

    Institute of Scientific and Technical Information of China (English)

    ZHU YongHui; LU dinYou; LIAO HongZhi; WANG diaSheng; FAN BeiLin; YAO ShiMing

    2008-01-01

    Erosion of cohesive sediment by flow is a very complicated phenomenon occurring worldwide. Understanding and modeling of the erosion process are important for many issues such as the breaching of embankments, riverbank stability, siltation of harbors and navigation channels, service life of reservoirs, distribution of (heavy metal) pollutants and water quality problems. In the last few decades, numerous studies have been done on the erosion of cohesive sediment by flow. Nevertheless, the factors affecting the erosion resistance of cohesive sediment are still not fully understood and the knowledge of the physics of cohesive sediment erosion is in-adequate, as a result the mathematical modeling of this erosion is far from saris-factory. In this paper an overview of the studies on the erosion resistance, erosion threshold and the erosion rate of cohesive sediment by flow is presented. The outcomes achieved so far from the studies and the existing problems have been analyzed and summarized, based on which recommendations are proposed for future research.

  18. Britishness and Community Cohesion in Muslim News Online

    Directory of Open Access Journals (Sweden)

    Hassen ZRIBA

    2013-12-01

    Full Text Available The issues of British national identity and social cohesion have become pressing concerns within the multicultural fabric of contemporary British society. The increasing number of immigrants and their offspring, along with the maintenance of their cultural roots, seem to represent a serious defiance to social cohesion and the alleged “purity” of Britishness. A number of race related reports were produced by the official authorities to churn out the necessary steps to be followed by the British (immigrants and host community in order to keep social stability and community cohesion. Thus, the politics of community cohesion came to the fore as the neologism of contemporary British political discourse. Such new discourse of governance has been digested and processed differently by different mass media. It has been decoded, for instance, preferably by mainstream news agencies like BBC News Online. However, arguably, it is read appositionally or at best negotiatedly by ethnicity-related news agencies such as Muslim News Online. In this article, attempt has been made to adopt media discourse analysis tools to decipher the ways Muslim News Online decoded and then encoded the hegemonic official discourses of Britishness and community cohesion. A critical and interpretative approach is used to accomplish such study. The corpus of this study is primarily extracted from the website of the Muslim News Online.

  19. Platelet-containing tantalum powders

    Energy Technology Data Exchange (ETDEWEB)

    Schiele, E.K.

    1988-04-26

    A method of forming platelet tantalum powders is described comprising the steps of: (a) providing an ingot-derived precursor tantalum powder, and (b) ball-milling the precursor powder for a time sufficient to form a platelet powder having an average FSSS of less than about 2 micrometers, a Scott density not greater than about 30 g/in/sup 3/ and a BET surface area of at least about 0.7 in/sup 2//g.

  20. LITERATURE REVIEW: HEAT TRANSFER THROUGH TWO-PHASE INSULATION SYSTEMS CONSISTING OF POWDERS IN A CONTINUOUS GAS PHASE

    Science.gov (United States)

    The report, a review of the literature on heat flow through powders, was motivated by the use of fine powder systems to produce high thermal resistivities (thermal resistance per unit thickness). he term "superinsulations" has been used to describe this type of material, which ha...

  1. Aerosolization properties, surface composition and physical state of spray-dried protein powders.

    Science.gov (United States)

    Bosquillon, Cynthia; Rouxhet, Paul G; Ahimou, François; Simon, Denis; Culot, Christine; Préat, Véronique; Vanbever, Rita

    2004-10-19

    Powder aerosols made of albumin, dipalmitoylphosphatidylcholine (DPPC) and a protein stabilizer (lactose, trehalose or mannitol) were prepared by spray-drying and analyzed for aerodynamic behavior, surface composition and physical state. The powders exited a Spinhaler inhaler as particle aggregates, the size of which depending on composition, spray-drying parameters and airflow rate. However, due to low bulk powder tap density (powders, respectively. Particle surface analysis by X-ray photoelectron spectroscopy (XPS) revealed a surface enrichment with DPPC relative to albumin for powders prepared under certain spray-drying conditions. DPPC self-organized in a gel phase in the particle and no sugar or mannitol crystals were detected by X-ray diffraction. Water sorption isotherms showed that albumin protected lactose from moisture-induced crystallization. In conclusion, a proper combination of composition and spray-drying parameters allowed to obtain dry powders with elevated fine particle fractions (FPFs) and a physical environment favorable to protein stability.

  2. Measuring Apparatus for Coal Powder

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The measuring apparatus for coal powder, equipped with radioactive source, is a set of device andcan be used to measure the density in the pipes and cumulative consumed amount of coal powder in apower plant, and to examine and display the status of the coal powder input system. It is sketched asFig. 1.

  3. Dependence of ripple dimensions on cohesive and non-cohesive bed properties in the intertidal Dee Estuary

    Science.gov (United States)

    Lichtman, Ian; Thorne, Peter; Baas, Jacobus; O'Boyle, Louise; Cooke, Richard; Amoudry, Laurent; Bell, Paul; Aspden, Rebecca; Bass, Sarah; Davies, Alan; Hope, Julie; Malarkey, Jonathan; Manning, Andrew; Parsons, Daniel; Paterson, David; Peakall, Jeffrey; Schindler, Robert; Ye, Leiping

    2014-05-01

    There is a need to better understand the effects of cohesive and mixed sediments on coastal processes, to improve sediment transport models for the management of coastal erosion, siltation of navigation channels and habitat change. Although reasonable sediment transport predictors are available for pure sands, it still is not the case for mixed cohesive and non-cohesive sediments. Existing predictors mostly relate ripple dimensions to hydrodynamic conditions and median sediment grain diameter, assuming a narrow unimodal particle size distribution. Properties typical of mixed conditions, such as composition and cohesion for example, are not usually taken into account. This presents severe shortcomings to predictors' abilities. Indeed, laboratory experiments using mixed cohesive sediments have shown that bedform dimensions decrease with increasing bed mud content. In the field, one may expect current predictors to match data for well-sorted sands closely, but poorly for mixed sediments. Our work is part of the COHBED project and aims to: (1) examine, in field conditions, if ripple dimensions are significantly different for mixed cohesive sediment beds compared to beds with pure sand; (2) compare the field data with laboratory results that showed reduced ripple length due to cohesive mud content; and (3) assess the performance of a selection of ripple predictors for mixed sediment data. The COHBED project was set up to undertake laboratory experiments and fieldwork to study how physical and biological processes influence bedform development in a mixed cohesive-cohesionless sediment environment. As part of COHBED, a suite of instruments was deployed on tidal flats in the Dee Estuary (on the NW coast of England), collecting co-located measurements of the hydrodynamics, suspended sediment properties and bed morphology. The instruments occupied three sites collecting data over different bed compositions during a two week period (21 May to 4 June 2013). One site was

  4. Cohesiveness in Financial News and its Relation to Market Volatility

    Science.gov (United States)

    Piškorec, Matija; Antulov-Fantulin, Nino; Novak, Petra Kralj; Mozetič, Igor; Grčar, Miha; Vodenska, Irena; Šmuc, Tomislav

    2014-05-01

    Motivated by recent financial crises, significant research efforts have been put into studying contagion effects and herding behaviour in financial markets. Much less has been said regarding the influence of financial news on financial markets. We propose a novel measure of collective behaviour based on financial news on the Web, the News Cohesiveness Index (NCI), and we demonstrate that the index can be used as a financial market volatility indicator. We evaluate the NCI using financial documents from large Web news sources on a daily basis from October 2011 to July 2013 and analyse the interplay between financial markets and finance-related news. We hypothesise that strong cohesion in financial news reflects movements in the financial markets. Our results indicate that cohesiveness in financial news is highly correlated with and driven by volatility in financial markets.

  5. Cohesiveness in financial news and its relation to market volatility.

    Science.gov (United States)

    Piškorec, Matija; Antulov-Fantulin, Nino; Novak, Petra Kralj; Mozetič, Igor; Grčar, Miha; Vodenska, Irena; Smuc, Tomislav

    2014-05-22

    Motivated by recent financial crises, significant research efforts have been put into studying contagion effects and herding behaviour in financial markets. Much less has been said regarding the influence of financial news on financial markets. We propose a novel measure of collective behaviour based on financial news on the Web, the News Cohesiveness Index (NCI), and we demonstrate that the index can be used as a financial market volatility indicator. We evaluate the NCI using financial documents from large Web news sources on a daily basis from October 2011 to July 2013 and analyse the interplay between financial markets and finance-related news. We hypothesise that strong cohesion in financial news reflects movements in the financial markets. Our results indicate that cohesiveness in financial news is highly correlated with and driven by volatility in financial markets.

  6. The development of cohesion in a learner corpus

    Directory of Open Access Journals (Sweden)

    Colleen A. Neary-Sundquist

    2013-10-01

    Full Text Available This study examines the use of cohesive devices (pragmatic markers and conjunctions in a 24,000-word corpus of transcribed oral data from 47 learners and native speakers of English. Both of these cohesive devices increase with proficiency level, but not in the same way. Conjunction use seems to increase steadily, and only the differences between the highest and lowest proficiency levels were found to be statistically significant. Pragmatic marker use, however, remains fairly stable across the three lowest proficiency levels and rises drastically for the two highest proficiency levels, and the two higher proficiency levels are significantly different from the two lower levels in their use of pragmatic markers. The results are compared to native speaker rates of cohesive device use for the same tasks and under the same conditions.

  7. Cohesion, consensus and extreme information in opinion dynamics

    CERN Document Server

    Sîrbu, Alina; Servedio, Vito D P; Tria, Francesca

    2013-01-01

    Opinion formation is an important element of social dynamics. It has been widely studied in the last years with tools from physics, mathematics and computer science. Here, a continuous model of opinion dynamics for multiple possible choices is analysed. Its main features are the inclusion of disagreement and possibility of modulating information, both from one and multiple sources. The interest is in identifying the effect of the initial cohesion of the population, the interplay between cohesion and information extremism, and the effect of using multiple sources of information that can influence the system. Final consensus, especially with external information, depends highly on these factors, as numerical simulations show. When no information is present, consensus or segregation is determined by the initial cohesion of the population. Interestingly, when only one source of information is present, consensus can be obtained, in general, only when this is extremely mild, i.e. there is not a single opinion stron...

  8. Applying a novel electrostatic dry powder coating technology to pellets.

    Science.gov (United States)

    Yang, Qingliang; Ma, Yingliang; Zhu, Jesse

    2015-11-01

    The present study aimed to apply a novel dry powder technology to coat pellets with different coating materials grounded into fine powders. Piroxicam, a non-steroidal anti-inflammatory drug, was used as the active pharmaceutical ingredient (API). Eudragit® EPO, Eudragit® RS/RL and Acryl EZE were used as the coating materials to achieve immediate release, sustained release and delayed release, respectively. Three steps including preheating, powder adhesion and curing were carried out to form the coating film while liquid plasticizers were used to decrease the glass transition temperature of coating powders and also served to reduce the electrical resistance of pellets. Results of SEM indicated coating film could be better formed by increasing curing temperature or extending curing time. Dissolution tests showed that three different drug release profiles, including immediate release, sustained release and delayed release, were achieved by this coating technology with different coating formulations. And the dry powder coated pellets using this developed technology exhibited an excellent stability with 1 month at 40 °C/75% RH. The coating procedure could be shortened to within 120 min and the use of fluidized hot air was minimized, both cutting down the overall cost dramatically compared to organic solvent coating and aqueous coating. All results demonstrated that the novel electrostatic dry powder coating method is a promising technology in the pharmaceutical coating industry.

  9. Elongational rheology and cohesive fracture of photo-oxidated LDPE

    Energy Technology Data Exchange (ETDEWEB)

    Rolón-Garrido, Víctor H., E-mail: victor.h.rolongarrido@tu-berlin.de; Wagner, Manfred H. [Chair of Polymer Engineering/Polymer Physics, Berlin Institute of Technology (TU Berlin), Fasanenstrasse 90, D-10623 Berlin (Germany)

    2014-01-15

    It was found recently that low-density polyethylene (LDPE) samples with different degrees of photo-oxidation represent an interesting system to study the transition from ductile to cohesive fracture and the aspects of the cohesive rupture in elongational flow. Sheets of LDPE were subjected to photo-oxidation in the presence of air using a xenon lamp to irradiate the samples for times between 1 day and 6 weeks. Characterisation methods included Fourier transform infrared spectroscopy, solvent extraction method, and rheology in shear and uniaxial extensional flows. Linear viscoelasticity was increasingly affected by increasing photo-oxidation due to crosslinking of LDPE, as corroborated by the carbonyl index, acid and aldehydes groups, and gel fraction. The molecular stress function model was used to quantify the experimental data, and the nonlinear model parameter β was found to be correlated with the gel content. The uniaxial data showed that the transition from ductile to cohesive fracture was shifted to lower elongational rates, the higher the gel content was. From 2 weeks photo-oxidation onwards, cohesive rupture occurred at every strain rate investigated. The true strain and true stress at cohesive fracture as well as the energy density applied to the sample up to fracture were analyzed. At low gel content, rupture was mainly determined by the melt fraction while at high gel content, rupture occurred predominantly in the gel structure. The strain at break was found to be independent of strain rate, contrary to the stress at break and the energy density. Thus, the true strain and not the stress at break or the energy density was found to be the relevant physical quantity to describe cohesive fracture behavior of photo-oxidated LDPE. The equilibrium modulus of the gel structures was correlated with the true strain at rupture. The stiffer the gel structure, the lower was the deformation tolerated before the sample breaks.

  10. Cohesive and coherent connected speech deficits in mild stroke.

    Science.gov (United States)

    Barker, Megan S; Young, Breanne; Robinson, Gail A

    2017-05-01

    Spoken language production theories and lesion studies highlight several important prelinguistic conceptual preparation processes involved in the production of cohesive and coherent connected speech. Cohesion and coherence broadly connect sentences with preceding ideas and the overall topic. Broader cognitive mechanisms may mediate these processes. This study aims to investigate (1) whether stroke patients without aphasia exhibit impairments in cohesion and coherence in connected speech, and (2) the role of attention and executive functions in the production of connected speech. Eighteen stroke patients (8 right hemisphere stroke [RHS]; 6 left [LHS]) and 21 healthy controls completed two self-generated narrative tasks to elicit connected speech. A multi-level analysis of within and between-sentence processing ability was conducted. Cohesion and coherence impairments were found in the stroke group, particularly RHS patients, relative to controls. In the whole stroke group, better performance on the Hayling Test of executive function, which taps verbal initiation/suppression, was related to fewer propositional repetitions and global coherence errors. Better performance on attention tasks was related to fewer propositional repetitions, and decreased global coherence errors. In the RHS group, aspects of cohesive and coherent speech were associated with better performance on attention tasks. Better Hayling Test scores were related to more cohesive and coherent speech in RHS patients, and more coherent speech in LHS patients. Thus, we documented connected speech deficits in a heterogeneous stroke group without prominent aphasia. Our results suggest that broader cognitive processes may play a role in producing connected speech at the early conceptual preparation stage. Copyright © 2017 Elsevier Inc. All rights reserved.

  11. Advanced powder processing

    Energy Technology Data Exchange (ETDEWEB)

    Janney, M.A. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    Gelcasting is an advanced powder forming process. It is most commonly used to form ceramic or metal powders into complex, near-net shapes. Turbine rotors, gears, nozzles, and crucibles have been successfully gelcast in silicon nitride, alumina, nickel-based superalloy, and several steels. Gelcasting can also be used to make blanks that can be green machined to near-net shape and then high fired. Green machining has been successfully applied to both ceramic and metal gelcast blanks. Recently, the authors have used gelcasting to make tooling for metal casting applications. Most of the work has centered on H13 tool steel. They have demonstrated an ability to gelcast and sinter H13 to near net shape for metal casting tooling. Also, blanks of H13 have been cast, green machined into complex shape, and fired. Issues associated with forming, binder burnout, and sintering are addressed.

  12. Powder detergents production plant

    Directory of Open Access Journals (Sweden)

    Stanković Mirjana S.

    2003-01-01

    Full Text Available The IGPC Engineering Department designed basic projects for powder detergent production plant, using technology developed in the IGPC laboratories, in 1998. - 2000. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, a production plant with a capacity of 25,000 t/y was manufactured, at "Delta In", Zrenjanin, in 2000.This technology was an innovation, because new approach in mixing a powder materials was used, as well as introducing a new type of dryer in detergent production. The product meets all quality demands for detergents with high specific weight (1000 g/l, as well as environmental regulations. The detergent production process is fully automatized, and the product has uniform quality. There is no waste material in detergent zeolite production, because all products with unsatisfactory quality are returned to the process. The production process can be controlled manually, which is necessary during start-up, and repairs.

  13. GROUP COHESION IN VOLLEYBALL CONTEXT OF THE STATE OF PARANÁ

    OpenAIRE

    Nascimento Junior, José Roberto Andrade do; Balbim,Guilherme Moraes; Vieira,Lenamar Fiorese

    2013-01-01

    Abstract: This descriptive correlational study aimed to analyze the perception of group cohesion of volleyball’s adult teams of state of Paraná. The subjects were 155 athletes male and female. The instruments used were the Group Environment Questionnaire (GEQ). For data analysis we applied the Kolmogorov-Smirnov test, Cronbach’s alpha, Spearman’s correlation, Mann-Whitney and Multiple Regression (p < 0.05). The results showed that teams had good levels of group cohesion and social to the task...

  14. Cohesive zone modelling and the fracture process of structural tape

    DEFF Research Database (Denmark)

    Stigh, Ulf; Biel, Anders; Svensson, Daniel

    2016-01-01

    Structural tapes provide comparable toughness as structural adhesives at orders of magnitude lower stresses. This is potentially useful to minimize the effects of differences in thermal expansion in the joining of mixed materials. The strength properties are modelled using the cohesive zone model....... Thus, a cohesive zone represents the tape, i.e. stresses in the tape are transmitted to the substrates through tractions determined by the separations of the surfaces of substrates. This simplification allows for structural analysis of large complex structures. The relation between the traction...

  15. GROUP COHESION IN VOLLEYBALL CONTEXT OF THE STATE OF PARANÁ

    OpenAIRE

    Nascimento Junior,José Roberto Andrade do; BALBIM,Guilherme Moraes; Vieira,Lenamar Fiorese

    2013-01-01

    Abstract: This descriptive correlational study aimed to analyze the perception of group cohesion of volleyball’s adult teams of state of Paraná. The subjects were 155 athletes male and female. The instruments used were the Group Environment Questionnaire (GEQ). For data analysis we applied the Kolmogorov-Smirnov test, Cronbach’s alpha, Spearman’s correlation, Mann-Whitney and Multiple Regression (p < 0.05). The results showed that teams had good levels of group cohesion and social to the task...

  16. ALTRUISM, EGOISM AND GROUP COHESION IN A LOCAL INTERACTION MODEL

    OpenAIRE

    José A. García Martínez

    2004-01-01

    In this paper we have introduced and parameterized the concept of ?group cohesion? in a model of local interaction with a population divided into groups. This allows us to control the level of ?isolation? of these groups: We thus analyze if the degree of group cohesion is relevant to achieve an efficient behaviour and which level would be the best one for this purpose. We are interested in situations where there is a trade off between efficiency and individual incentives. This trade off is st...

  17. Dispersing powders in liquids

    CERN Document Server

    Nelson, RD

    1988-01-01

    This book provides powder technologists with laboratory procedures for selecting dispersing agents and preparing stable dispersions that can then be used in particle size characterization instruments. Its broader goal is to introduce industrial chemists and engineers to the phenomena, terminology, physical principles, and chemical considerations involved in preparing and handling dispersions on a commercial scale. The book introduces novices to: - industrial problems due to improper degree of dispersion; - the nomenclature used in describing particles; - the basic physica

  18. Formulation pre-screening of inhalation powders using computational atom-atom systematic search method.

    Science.gov (United States)

    Ramachandran, Vasuki; Murnane, Darragh; Hammond, Robert B; Pickering, Jonathan; Roberts, Kevin J; Soufian, Majeed; Forbes, Ben; Jaffari, Sara; Martin, Gary P; Collins, Elizabeth; Pencheva, Klimentina

    2015-01-05

    The synthonic modeling approach provides a molecule-centered understanding of the surface properties of crystals. It has been applied extensively to understand crystallization processes. This study aimed to investigate the functional relevance of synthonic modeling to the formulation of inhalation powders by assessing cohesivity of three active pharmaceutical ingredients (APIs, fluticasone propionate (FP), budesonide (Bud), and salbutamol base (SB)) and the commonly used excipient, α-lactose monohydrate (LMH). It is found that FP (-11.5 kcal/mol) has a higher cohesive strength than Bud (-9.9 kcal/mol) or SB (-7.8 kcal/mol). The prediction correlated directly to cohesive strength measurements using laser diffraction, where the airflow pressure required for complete dispersion (CPP) was 3.5, 2.0, and 1.0 bar for FP, Bud, and SB, respectively. The highest cohesive strength was predicted for LMH (-15.9 kcal/mol), which did not correlate with the CPP value of 2.0 bar (i.e., ranking lower than FP). High FP-LMH adhesive forces (-11.7 kcal/mol) were predicted. However, aerosolization studies revealed that the FP-LMH blends consisted of agglomerated FP particles with a large median diameter (∼4-5 μm) that were not disrupted by LMH. Modeling of the crystal and surface chemistry of LMH identified high electrostatic and H-bond components of its cohesive energy due to the presence of water and hydroxyl groups in lactose, unlike the APIs. A direct comparison of the predicted and measured cohesive balance of LMH with APIs will require a more in-depth understanding of highly hydrogen-bonded systems with respect to the synthonic engineering modeling tool, as well as the influence of agglomerate structure on surface-surface contact geometry. Overall, this research has demonstrated the possible application and relevance of synthonic engineering tools for rapid pre-screening in drug formulation and design.

  19. Which fine-tuning arguments are fine?

    CERN Document Server

    Grinbaum, Alexei

    2009-01-01

    The argument from naturalness is widely employed in contemporary quantum field theory. Essentially a formalized aesthetic criterion, it received a meaning in the debate on the Higgs mechanism, which goes beyond aesthetics. We follow the history of technical definitions of fine tuning at the scale of electroweak symmetry breaking. It is argued that they give rise to a special interpretation of probability, which we call Gedankenfrequency. By extension of its original meaning, the argument from naturalness is used to compare different models beyond the Standard Model. We show that in this case naturalness cannot be defined objectively. Rather, it functions as socio-historical heuristics in particle physics and it contributes to the advent of a probabilistic version of Popper's falsificationism.

  20. Relationship of Powder Feedstock Variability to Microstructure and Defects in Selective Laser Melted Alloy 718

    Science.gov (United States)

    Smith, T. M.; Kloesel, M. F.; Sudbrack, C. K.

    2017-01-01

    Powder-bed additive manufacturing processes use fine powders to build parts layer by layer. For selective laser melted (SLM) Alloy 718, the powders that are available off-the-shelf are in the 10-45 or 15-45 micron size range. A comprehensive investigation of sixteen powders from these typical ranges and two off-nominal-sized powders is underway to gain insight into the impact of feedstock on processing, durability and performance of 718 SLM space-flight hardware. This talk emphasizes an aspect of this work: the impact of powder variability on the microstructure and defects observed in the as-fabricated and full heated material, where lab-scale components were built using vendor recommended parameters. These typical powders exhibit variation in composition, percentage of fines, roughness, morphology and particle size distribution. How these differences relate to the melt-pool size, porosity, grain structure, precipitate distributions, and inclusion content will be presented and discussed in context of build quality and powder acceptance.

  1. Mechanical alloying of Al-3 at. % Mo powders

    Energy Technology Data Exchange (ETDEWEB)

    Zdujic, M. (Srpska Akademija Nauka i Umetnosti, Belgrade (Yugoslavia). Dept. of Technical Science); Kobayashi, K.F. (Osaka Univ., Suita (Japan). Dept. of Welding and Production Engineering); Shingu, P.H. (Kyoto Univ. (Japan). Dept. of Metal Science and Technology)

    1990-05-01

    Mechanical alloying of elemental powders of aluminum and molybdenum (Al-3 at.% Mo) has been carried out in a conventional horizontal ball mill up to 1000 h of milling time. Mechanically alloyed powders were investigated by scanning electron microscopy, X-ray diffraction analysis and differential scanning calorimetry. After prolonged milling time molybdenum was finely dispersed in aluminum matrix. The dispersoid sizes were less than about 100 nm, with average size considerably smaller. By the heat treatment of the mechanically alloyed powders, the intermetallic compound Al{sub 12}Mo was formed. The reaction temperature for the formation of Al{sub 12}Mo decreased with increasing milling time. The Johnson-Mehl-Avrami exponent of n=2.8{plus minus}0.3 for the formation of Al{sub 12}Mo was obtained with the apparent activation energy of 165{plus minus}12 kJ/mol (1.7{plus minus}0.1 eV). (orig.).

  2. Liposomal dry powders as aerosols for pulmonary delivery of proteins.

    Science.gov (United States)

    Lu, Dongmei; Hickey, Anthony J

    2005-12-21

    The purpose of this research was to develop liposomal dry powder aerosols for protein delivery. The delivery of stable protein formulations is essential for protein subunit vaccine delivery, which requires local delivery to macrophages in the lungs. Beta-glucuronidase (GUS) was used as a model protein to evaluate dry powder liposomes as inhaled delivery vehicles. Dimyristoyl phosphatylcholine:cholesterol (7:3) was selected as the liposome composition. The lyophilization of liposomes, micronization of the powders, aerosolization using a dry powder inhaler (DPI), and in vitro aerodynamic fine particle fraction upon collection in a twin-stage liquid impinger were evaluated. After lyophilization and jet-milling, the total amount of GUS and its activity, representing encapsulation efficiency and stability, were evaluated. The GUS amount and activity were measured and compared with freshly-prepared liposomes in the presence of mannitol, 43% of initial GUS amount, 29% of GUS activity after lyophilization and 36% of GUS amount, 22% of activity after micronization were obtained. Emitted doses from dry powder inhaler were 53%, 58%, 66%, and 73% for liposome powder:mannitol carrier ratios of 1:0, 1:4, 1:9, and 1:19. Fifteen percent of the liposome particles were less than 6.4 mum in aerodynamic diameter. The results demonstrate that milled liposome powders containing protein molecules can be aerosolized effectively at a fixed flow rate. Influences of different cryoprotectants on lyophilization of protein liposome formulations are reported. The feasibility of using liposomal dry powder aerosols for protein delivery has been demonstrated but further optimization is required in the context of specific therapeutic proteins.

  3. The Application of Powder Rheology in Additive Manufacturing

    Science.gov (United States)

    Clayton, Jamie; Millington-Smith, Doug; Armstrong, Brian

    2015-03-01

    Additive manufacturing (AM) is sensitive to powder variability when applying fine layers in a uniform manner. This demands a high degree of consistency and repeatability in the feedstock. Particle size is often used as a critical quality attribute, but this is not sufficient to fully qualify a feedstock. Indeed, it is inadequate to suggest that any parameter from a single test, e.g., Hall flowmeter or Hausner ratio, can comprehensively describe a powder's characteristics. This article uses four case studies to demonstrate the limitations of single parameter characterization and how the rheological properties of several metal powders used in AM applications are used to establish in-process performance. In the first study, the significantly reduced permeability and increased specific energy of a one batch of powder demonstrate a clear link to poor layer uniformity. The second study investigates the impact of metal powder manufacturing methods and suppliers, and it shows how shear properties alone cannot be relied on to identify properties that influence the process. The effect of additives on the processability of polymer blends used in AM is also evaluated, and the results show that even small quantities can have a significant effect on the permeability and basic flowability energy of feedstocks. The final study demonstrates the how rheological measurements can be used to identify the optimum blend of fresh and used material when reusing metal powders to manufacture components. These case studies illustrate the ability of a modern powder rheometer to detect minor variations in powders that are directly relevant to performance in AM processes in a way that traditional characterization methods cannot.

  4. Performance Characteristics of Waste Glass Powder Substituting Portland Cement in Mortar Mixtures

    Science.gov (United States)

    Kara, P.; Csetényi, L. J.; Borosnyói, A.

    2016-04-01

    In the present work, soda-lime glass cullet (flint, amber, green) and special glass cullet (soda-alkaline earth-silicate glass coming from low pressure mercury-discharge lamp cullet and incandescent light bulb borosilicate glass waste cullet) were ground into fine powders in a laboratory planetary ball mill for 30 minutes. CEM I 42.5N Portland cement was applied in mortar mixtures, substituted with waste glass powder at levels of 20% and 30%. Characterisation and testing of waste glass powders included fineness by laser diffraction particle size analysis, specific surface area by nitrogen adsorption technique, particle density by pycnometry and chemical analysis by X-ray fluorescence spectrophotometry. Compressive strength, early age shrinkage cracking and drying shrinkage tests, heat of hydration of mortars, temperature of hydration, X-ray diffraction analysis and volume stability tests were performed to observe the influence of waste glass powder substitution for Portland cement on physical and engineering properties of mortar mixtures.

  5. Compacted and Sintered Microstructure Depending on Uranium Powder Size in Zr-U Metallic Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Yun, Chang Gun; Jun, Hyun-Joon; Ju, Jung Hwan; Lee, Ho Jin; Lee, Chong-Tak; Kim, Hyung Lae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2017-03-15

    In case of the uranium (U) and zirconium (Zr) powders which have been utilized for the production of a metallic fuel in the various nuclear applications, the homogenous distribution of U powders in the Zr-U pellet has influenced significantly on the nuclear fuel performance. The inhomogeneity in a powder process was changed by various intricate factors, e.g. powder size, shape, distribution and so on. Particularly, the U inhomogeneity in the Zr-U pellets occurs by segregation derived from the great gaps of densities between Zr and U during compaction of the mixed powders. In this study, the relationship between powder size and homogeneity was investigated by using the different-sized U powders. The microstructure in Zr-U pellets reveals more homogeneity when the weight ration of Zr and U powders are close to 1. In addition, homogeneous pellets which were produced by fine U powders have higher density because the homogeneity affects the alloying reaction during sintering and the densification behavior of pore induced by powder size.

  6. Comprehensive Evaluation of Powdered Chinese Herbal Medicines-An Exemplification of Isatidis Radix

    Institute of Scientific and Technical Information of China (English)

    Xue Han; Ming-quan Wu; Zhi-rui Yang; Ding-kun Zhang; Yi Mao; Jin Han; Yin-qiu Huang; Yong-feng Zhou; Yan-ling Zhao; Jia-bo Wang; Xiao-he Xiao

    2016-01-01

    Objective Currently, powdered Chinese herbal medicines(CHMs) were mainly evaluated through physical property, chemical dissolution, and bioactivity independently. It could not reflect the quality comprehensively. This paper was to explore and establish a comprehensive evaluation method for powdered CHMs. Methods Isatidis Radix was chosen as an exemple. Firstly, powdered Isatidis Radix in different particle size was prepared. Then, their physical properties were characterized. The dissolution of index component epigoitrin was determined, and their antiviral activities were evaluated by neuraminidase-based bioassay. Results As the particle size decreased, powder distribution tended to be uniform, and the dissolution of epigoitrin increased, antiviral activity enhanced. According to cluster analysis of above results, the sequence of evaluation consequence was ultrafine powder S2(D90: 32.80 ± 0.29) > ultrafine powder S1(D90: 52.08 ± 0.53) > fine powder S0(D90: 118.16 ± 0.76)(from the superior to the inferior). Conclusion Overall, the comprehensive evaluation for powdered CHMs based on the physical characterization, chemical dissolution, and bioassay could not only be used to evaluate powdered herbs, but also guide the screening and optimization of the particle size of powder.

  7. Fine 5 lavastab Venemaal

    Index Scriptorium Estoniae

    2013-01-01

    Tantsuteatru Fine 5 koreograafid Tiina Ollesk ja Rene Nõmmik toovad Jekaterinburgis välja lavastuse "... and Red", esitajaks Venemaa nimekas nüüdistantsutrupp Provintsialnõje Tantsõ. Lavastuses kõlab Taavo Remmeli kontrabassiimprovisatsioon "12.12.2006"

  8. A fine art

    Energy Technology Data Exchange (ETDEWEB)

    Schnabel, G.; Raaff, T. [Andritz AG (Austria)

    2006-07-15

    The paper describes a new dewatering system for coal fines which challenges established processes by using screenbowl centrifuge and hyperbaric filter combinations. Company acquisitions over the past three to four years enabled Andritz AG to develop a new system combining two technologies. The article describes the benefits of the combination process and explains the basic operation of these machines. 4 figs.

  9. The Fine Dutch Tradition

    NARCIS (Netherlands)

    Hooimeijer, F.L.

    2012-01-01

    Publication of the exhibition and symposium on water adaptive urban planning and architecture in Bangkok. The Urban Fine Dutch Tradition is a dynamic tradition of making urban designs using the parameters of the natural system – incorperating in an efficient way the hydrological cycle, the soil and

  10. Imeilus Fine 5

    Index Scriptorium Estoniae

    2017-01-01

    Vaba Lava teatrikeskuse laval esineb Fine 5 oma lavastusega "Imeilus". Tiina Ollesk ja Renee Nõmmik, tantsulavastuse autorid on koreograafid, õppejõud, lavastajad ja kogemustega tantsijad. 29. jaanuaril korraldavad Tiina Ollesk ja Renee Nõmmik Tallinna Ülikoolis kaasaegse liikumismõtlemise töötoa, mis on pühendatud lavastusele "Imeilus"

  11. Fine 5 lavastab Venemaal

    Index Scriptorium Estoniae

    2013-01-01

    Tantsuteatru Fine 5 koreograafid Tiina Ollesk ja Rene Nõmmik toovad Jekaterinburgis välja lavastuse "... and Red", esitajaks Venemaa nimekas nüüdistantsutrupp Provintsialnõje Tantsõ. Lavastuses kõlab Taavo Remmeli kontrabassiimprovisatsioon "12.12.2006"

  12. Using of fluidized-bed jet mill to a super fine comminution of steel composite

    Directory of Open Access Journals (Sweden)

    D. Urbaniak

    2015-01-01

    Full Text Available In many industries the demand for very fine material increases. In the metallurgical industry, for example, there is increasing use of the production of high density metal elements with the use of metallurgical powder composites. The use of powder composites requires prior their grinding. Unfortunately, the very fine grinding is not an easy process. The using for this purpose fluidized-bed jet mill was proposed in the paper. The attempts of grinding of metallurgical powder were carried out in the fluidized-bed jet mill. After the experiment analyses of particle size distribution of grinding products were performed. The results are presented in graphs. Analyses of the obtained results concluded that the grinding of very fine metallurgical composite is possible and produces positive results.

  13. Numerical Analysis of the Effect of Particle Shape and Adhesion on the Segregation of Powder Mixtures

    Science.gov (United States)

    Alizadeh Behjani, Mohammadreza; Hassanpour, Ali; Ghadiri, Mojtaba; Bayly, Andrew

    2017-06-01

    Segregation of granules is an undesired phenomenon in which particles in a mixture separate from each other based on the differences in their physical and chemical properties. It is, therefore, crucial to control the homogeneity of the system by applying appropriate techniques. This requires a fundamental understanding of the underlying mechanisms. In this study, the effect of particle shape and cohesion has been analysed. As a model system prone to segregation, a ternary mixture of particles representing the common ingredients of home washing powders, namely, spray dried detergent powders, tetraacetylethylenediamine, and enzyme placebo (as the minor ingredient) during heap formation is modelled numerically by the Discrete Element Method (DEM) with an aim to investigate the effect of cohesion/adhesion of the minor components on segregation quality. Non-spherical particle shapes are created in DEM using the clumped-sphere method based on their X-ray tomograms. Experimentally, inter particle adhesion is generated by coating the minor ingredient (enzyme placebo) with Polyethylene Glycol 400 (PEG 400). The JKR theory is used to model the cohesion/adhesion of coated enzyme placebo particles in the simulation. Tests are carried out experimentally and simulated numerically by mixing the placebo particles (uncoated and coated) with the other ingredients and pouring them in a test box. The simulation and experimental results are compared qualitatively and quantitatively. It is found that coating the minor ingredient in the mixture reduces segregation significantly while the change in flowability of the system is negligible.

  14. Numerical Analysis of the Effect of Particle Shape and Adhesion on the Segregation of Powder Mixtures

    Directory of Open Access Journals (Sweden)

    Alizadeh Behjani Mohammadreza

    2017-01-01

    Full Text Available Segregation of granules is an undesired phenomenon in which particles in a mixture separate from each other based on the differences in their physical and chemical properties. It is, therefore, crucial to control the homogeneity of the system by applying appropriate techniques. This requires a fundamental understanding of the underlying mechanisms. In this study, the effect of particle shape and cohesion has been analysed. As a model system prone to segregation, a ternary mixture of particles representing the common ingredients of home washing powders, namely, spray dried detergent powders, tetraacetylethylenediamine, and enzyme placebo (as the minor ingredient during heap formation is modelled numerically by the Discrete Element Method (DEM with an aim to investigate the effect of cohesion/adhesion of the minor components on segregation quality. Non-spherical particle shapes are created in DEM using the clumped-sphere method based on their X-ray tomograms. Experimentally, inter particle adhesion is generated by coating the minor ingredient (enzyme placebo with Polyethylene Glycol 400 (PEG 400. The JKR theory is used to model the cohesion/adhesion of coated enzyme placebo particles in the simulation. Tests are carried out experimentally and simulated numerically by mixing the placebo particles (uncoated and coated with the other ingredients and pouring them in a test box. The simulation and experimental results are compared qualitatively and quantitatively. It is found that coating the minor ingredient in the mixture reduces segregation significantly while the change in flowability of the system is negligible.

  15. An examination of the relationship between athlete leadership and cohesion using social network analysis.

    Science.gov (United States)

    Loughead, Todd M; Fransen, Katrien; Van Puyenbroeck, Stef; Hoffmann, Matt D; De Cuyper, Bert; Vanbeselaere, Norbert; Boen, Filip

    2016-11-01

    Two studies investigated the structure of different athlete leadership networks and its relationship to cohesion using social network analysis. In Study 1, we examined the relationship between a general leadership quality network and task and social cohesion as measured by the Group Environment Questionnaire (GEQ). In Study 2, we investigated the leadership networks for four different athlete leadership roles (task, motivational, social and external) and their association with task and social cohesion networks. In Study 1, the results demonstrated that the general leadership quality network was positively related to task and social cohesion. The results from Study 2 indicated positive correlations between the four leadership networks and task and social cohesion networks. Further, the motivational leadership network emerged as the strongest predictor of the task cohesion network, while the social leadership network was the strongest predictor of the social cohesion network. The results complement a growing body of research indicating that athlete leadership has a positive association with cohesion.

  16. Perceived Community Cohesion and the Stress Process in Youth

    Science.gov (United States)

    Van Gundy, Karen T.; Stracuzzi, Nena F.; Rebellon, Cesar J.; Tucker, Corinna Jenkins; Cohn, Ellen S.

    2011-01-01

    Using survey data from two youth samples, one rural and one urban, we examine the role and significance of perceived community cohesion in the stress process. In particular, we assess the extent to which community attachment and detachment are related to depressed mood, problem substance use, and delinquency net of social statuses, stress…

  17. Modelling of Cohesive Sediment Transport in the Maasmond Area

    NARCIS (Netherlands)

    Wang, L.

    2006-01-01

    In the Dutch coastal zone, where the marine environment is highly dynamic owing to tidal currents, wind-driven, wave-driven, and density-driven currents and waves, the cohesive sediment dynamics is always a great concern to transportation authority and coastal managers. So far, a lot research has

  18. A cohesive zone framework for environmentally assisted fatigue

    DEFF Research Database (Denmark)

    del Busto, Susana; Betegón, Covadonga; Martínez Pañeda, Emilio

    2017-01-01

    We present a compelling finite element framework to model hydrogen assisted fatigue by means of a hydrogen- and cycle-dependent cohesive zone formulation. The model builds upon: (i) appropriate environmental boundary conditions, (ii) a coupled mechanical and hydrogen diffusion response, driven...

  19. Examining the Relationship between Emotional Intelligence and Group Cohesion

    Science.gov (United States)

    Moore, Amanda; Mamiseishvili, Ketevan

    2012-01-01

    Collaborative learning experiences increase student learning, but what happens when students fail to collaborate? The authors investigated the relationship between emotional intelligence and group cohesion by studying 44 undergraduate teams who were completing semester-long projects in their business classes at a small private university in the…

  20. Cohesiveness and Interpersonal Attraction: A Selected, Annotated Basic Bibliography.

    Science.gov (United States)

    Beebe, Steven A.; Webb, Marsha Short

    This 43-item selected, annotated bibliography on cohesiveness and interpersonal attraction includes books, journal articles and conference papers published between 1953 and 1990. The bibliography is in two parts. The first part consists of key sources, most of which have extensive bibliographies or lists of references. The second part consists of…

  1. Visibility and anonymity effects on attraction and group cohesiveness

    NARCIS (Netherlands)

    Lea, Martin; Spears, Russell; Watt, Susan E.

    2007-01-01

    This study investigated attraction and group cohesiveness under different visibility and anonymity conditions for social categories that differed in their capacity to be visually cued. Using computer-mediated communication in 36 mixed gender (visually cued category) and nationality (non-visually

  2. Instruments used in the research on Cohesive Sediments

    NARCIS (Netherlands)

    De Wit, P.J.

    1992-01-01

    A research program was started to study the behaviour of cohesive sediments at the Delft University of Technology in 1989. As part of this project a well-provided physico-chemicallaboratory was built within the Hydromechanics Laboratory and adequate instrumentation was purchased. These new instrumen

  3. The Relationship between Social Cohesion and Computer-Internet Usage

    Science.gov (United States)

    Balkan, Emre; Adalier, Ahmet

    2011-01-01

    The aim of this study is to analyze the relationship between social cohesion and computer-internet usage among university students. The research was conducted among university students in North Cyprus. The sample for the research consists of 38.8% (n=80) female, 61.2 % (n=126) male, 206 university students by using the criterion sampling method.…

  4. Cohesion and device reliability in organic bulk heterojunction photovoltaic cells

    KAUST Repository

    Brand, Vitali

    2012-04-01

    The fracture resistance of P3HT:PC 60BM-based photovoltaic devices are characterized using quantitative adhesion and cohesion metrologies that allow identification of the weakest layer or interface in the device structure. We demonstrate that the phase separated bulk heterojunction layer is the weakest layer and report quantitative cohesion values which ranged from ∼1 to 20 J m -2. The effects of layer thickness, composition, and annealing treatments on layer cohesion are investigated. Using depth profiling and X-ray photoelectron spectroscopy on the resulting fracture surfaces, we examine the gradient of molecular components through the thickness of the bulk heterojunction layer. Finally, using atomic force microscopy we show how the topography of the failure path is related to buckling of the metal electrode and how it develops with annealing. The research provides new insights on how the molecular design, structure and composition affect the cohesive properties of organic photovoltaics. © 2011 Elsevier B.V. All rights reserved.

  5. Some Measures of Interpersonal Attraction and Group Cohesiveness.

    Science.gov (United States)

    Aiken, Lewis R.

    1992-01-01

    The computation and determination of the statistical significance of three coefficients of interpersonal attractiveness or cohesiveness in task-oriented or social groups are described. The approach is based on ratings made by each member of a group of all other group members. Experience using the technique is reviewed. (SLD)

  6. Cohesive Errors in Writing among ESL Pre-Service Teachers

    Science.gov (United States)

    Kwan, Lisa S. L.; Yunus, Melor Md

    2014-01-01

    Writing is a complex skill and one of the most difficult to master. A teacher's weak writing skills may negatively influence their students. Therefore, reinforcing teacher education by first determining pre-service teachers' writing weaknesses is imperative. This mixed-methods error analysis study aims to examine the cohesive errors in the writing…

  7. New African Pentecostalism and social cohesion in South Africa

    African Journals Online (AJOL)

    engagement of New African Pentecostalism (NAP) in the process of social cohesion in South ..... strategy. Such a dualistic worldview seems to have prevented Pentecostals ... also involved in vicious competition for members and accusations of .... the movement is 'a kind of ecumenical [hybrid/contaminated] movement,.

  8. Long Fibre Composite Modelling Using Cohesive User's Element

    Science.gov (United States)

    Kozák, Vladislav; Chlup, Zdeněk

    2010-09-01

    The development glass matrix composites reinforced by unidirectional long ceramic fibre has resulted in a family of very perspective structural materials. The only disadvantage of such materials is relatively high brittleness at room temperature. The main micromechanisms acting as toughening mechanism are the pull out, crack bridging, matrix cracking. There are other mechanisms as crack deflection etc. but the primer mechanism is mentioned pull out which is governed by interface between fibre and matrix. The contribution shows a way how to predict and/or optimise mechanical behaviour of composite by application of cohesive zone method and write user's cohesive element into the FEM numerical package Abaqus. The presented results from numerical calculations are compared with experimental data. Crack extension is simulated by means of element extinction algorithms. The principal effort is concentrated on the application of the cohesive zone model with the special traction separation (bridging) law and on the cohesive zone modelling. Determination of micro-mechanical parameters is based on the combination of static tests, microscopic observations and numerical calibration procedures.

  9. Visibility and anonymity effects on attraction and group cohesiveness

    NARCIS (Netherlands)

    Lea, Martin; Spears, Russell; Watt, Susan E.

    2007-01-01

    This study investigated attraction and group cohesiveness under different visibility and anonymity conditions for social categories that differed in their capacity to be visually cued. Using computer-mediated communication in 36 mixed gender (visually cued category) and nationality (non-visually cue

  10. Effects of Textual and Cohesive Structure on Discourse Processing.

    Science.gov (United States)

    Hoover, Michael L.

    1997-01-01

    Indicates a facilitation in undergraduate students' reading time for congruent text marking for both cohesion and textual structure that manifested itself at different points in the sentence. Suggests that readers are highly sensitive to coherence marking devices, and strictly local coherence models cannot completely account for what readers are…

  11. Resolving Signals to Cohesion: Two Models of Bridging Inference.

    Science.gov (United States)

    Hegarty, Mary; Revlin, Russell

    1999-01-01

    Suggests two models of how readers create bridging inferences to resolve signals to textual cohesion. Evaluates reading times, verification accuracy, verification latency, and regressive eye fixations to support the model which views bridges as the result of a form of deduction in which the reader tacitly establishes premises that provide rational…

  12. ReaderBench: An Integrated Cohesion-Centered Framework

    NARCIS (Netherlands)

    Dascalu, Mihai; Stavarache, Larise; Dessus, Philippe; Trausan-Matu, Stefan; McNamara, Danielle; Bianco, Maryse

    2015-01-01

    Dascalu, M., Stavarache, L.L., Dessus, P., Trausan-Matu, S., McNamara, D.S., & Bianco, M. (2015). ReaderBench: An Integrated Cohesion-Centered Framework. In G. Conole, T. Klobucar, C. Rensing, J. Konert & É. Lavoué (Eds.), 10th European Conf. on Technology Enhanced Learning (pp. 505–508). Toledo, Sp

  13. The Development of the Perception of Textual Cohesion.

    Science.gov (United States)

    Chapman, L. J.

    Three experiments examined children's ability to perceive two of the elements of textual cohesion--personal reference and conjunction. The first experiment investigated the ability of 76 eight-year-old children to process anaphora in order to distinguish those children who were becoming fluent readers from those who were not. The children were…

  14. Children's Problems with Focus and Cohesion in Revising.

    Science.gov (United States)

    Champagne, Mireille; And Others

    A study was conducted to determine whether children in revising their writing to accommodate new information would make corresponding textual changes to preserve appropriate focus and cohesion. The subjects, 48 children each from grades three, six, and nine, were presented with a task that involved descriptions of pictures with incongruent…

  15. A Cohesive and Coherent Analysis of The Purloined Letter

    Institute of Scientific and Technical Information of China (English)

    杜娟娟; 郭鸿雁

    2013-01-01

      The thesis aims to do a research on the cohesion and coherence in The Purloined Letter written by Edgar Allan Poe based on the theories of Halliday and Hasan as well as the Chinese scholars Zhang Delu and Liu Rushan. By the means of them, Poe’s ingenious composition and vivid characters emerge in the mind of the readers.

  16. Behavioural Contagion Explains Group Cohesion in a Social Crustacean.

    Directory of Open Access Journals (Sweden)

    Pierre Broly

    2015-06-01

    Full Text Available In gregarious species, social interactions maintain group cohesion and the associated adaptive values of group living. The understanding of mechanisms leading to group cohesion is essential for understanding the collective dynamics of groups and the spatio-temporal distribution of organisms in environment. In this view, social aggregation in terrestrial isopods represents an interesting model due to its recurrence both in the field and in the laboratory. In this study, and under a perturbation context, we experimentally tested the stability of groups of woodlice according to group size and time spent in group. Our results indicate that the response to the disturbance of groups decreases with increases in these two variables. Models neglecting social effects cannot reproduce experimental data, attesting that cohesion of aggregation in terrestrial isopods is partly governed by a social effect. In particular, models involving calmed and excited individuals and a social transition between these two behavioural states more accurately reproduced our experimental data. Therefore, we concluded that group cohesion (and collective response to stimulus in terrestrial isopods is governed by a transitory resting state under the influence of density of conspecifics and time spent in group. Lastly, we discuss the nature of direct or indirect interactions possibly implicated.

  17. Meiotic sister chromatid cohesion and recombination in two filamentous fungi

    NARCIS (Netherlands)

    Heemst, van D.

    2000-01-01

    Homologous recombination and sister chromatid cohesion play important roles in the maintenance of genome integrity and the fidelity of chromosome segregation in mitosis and meiosis. Within the living cell, the integrity of the DNA is threatened by various factors that cause DNA-lesions, of which DNA

  18. Possibilities for Social Cohesion in Education: Bosnia-Herzegovina

    Science.gov (United States)

    Hill, Kelly

    2011-01-01

    In postwar Bosnia-Herzegovina, segregation along ethno-nationalistic lines and divergent pedagogies within the education system have presented challenges to social cohesion and the long-term stability of a society that is still struggling to rebuild, reconcile, and regain trust (Jancic, 2008). This article examines the current state of the…

  19. Teacher Governance Factors and Social Cohesion: Insights from Pakistan

    Science.gov (United States)

    Halai, Anjum; Durrani, Naureen

    2016-01-01

    This paper explores teacher governance factors, particularly recruitment and deployment of teachers, in relation to inequalities and social cohesion. Pakistan introduced major reforms in education in the post 9/11 context of escalating conflict. These include a merit and needs-based policy on teacher recruitment to eliminate corruption in…

  20. Cohesion and coordination effects on transition metal surface energies

    Science.gov (United States)

    Ruvireta, Judit; Vega, Lorena; Viñes, Francesc

    2017-10-01

    Here we explore the accuracy of Stefan equation and broken-bond model semiempirical approaches to obtain surface energies on transition metals. Cohesive factors are accounted for either via the vaporization enthalpies, as proposed in Stefan equation, or via cohesive energies, as employed in the broken-bond model. Coordination effects are considered including the saturation degree, as suggested in Stefan equation, employing Coordination Numbers (CN), or as the ratio of broken bonds, according to the bond-cutting model, considering as well the square root dependency of the bond strength on CN. Further, generalized coordination numbers CN bar are contemplated as well, exploring a total number of 12 semiempirical formulations on the three most densely packed surfaces of 3d, 4d, and 5d Transition Metals (TMs) displaying face-centered cubic (fcc), body-centered cubic (bcc), or hexagonal close-packed (hcp) crystallographic structures. Estimates are compared to available experimental surface energies obtained extrapolated to zero temperature. Results reveal that Stefan formula cohesive and coordination dependencies are only qualitative suited, but unadvised for quantitative discussion, as surface energies are highly overestimated, favoring in addition the stability of under-coordinated surfaces. Broken-bond cohesion and coordination dependencies are a suited basis for quantitative comparison, where square-root dependencies on CN to account for bond weakening are sensibly worse. An analysis using Wulff shaped averaged surface energies suggests the employment of broken-bond model using CN to gain surface energies for TMs, likely applicable to other metals.