WorldWideScience

Sample records for coaxial nanotube heterostructure

  1. Synthesis and optical properties of ZnO and carbon nanotube based coaxial heterostructures

    Science.gov (United States)

    Kim, D. S.; Lee, S.-M.; Scholz, R.; Knez, M.; Gösele, U.; Fallert, J.; Kalt, H.; Zacharias, M.

    2008-09-01

    Carbon nanotubes and ZnO based functional coaxial heterostructured nanotubes have been fabricated by using atomic layer deposition. An irregular structured shell composed of ZnO nanocrystals was deposited on pristine nanotubes, while a highly defined ZnO shell was deposited on the tubes after its functionalization with Al2O3. Photoluminescence measurements of the ZnO shell on Al2O3/nanotube show a broad green band emission, whereas the shell grown on the bare nanotube shows a band shifted to the orange spectral range.

  2. Synthesis of ZnO nanotube arrays and heterostructures of Cu-ZnO coaxial nanotubes by electrodeposition-oxidation method.

    Science.gov (United States)

    Ren, Xin; Jiang, Chuanhai

    2010-08-01

    Semiconductor ZnO nanotube arrays and heterostructures of Cu-ZnO coaxial nanotubes have been synthesized by electrodeposition into porous anodic alumina membranes and subsequent oxidation. Scanning electron microscopy and transmission electron microscopy indicate that the ZnO nanotubular arrays and Cu-ZnO coaxial nanotubular arrays are of large-area and highly ordered. X-ray diffraction patterns show that the nanotubes are polycrystalline. Photoluminescence spectra of the Cu-ZnO nanotubes show that a violet peak, a blue peak and a green peak are centered at 422 nm, 480 nm and 537 nm, respectively. The ordered ZnO nanotube arrays and heterostructures of Cu-ZnO coaxial nanotubes may have promising potential applications in nanodevices.

  3. Co-axial heterostructures integrating palladium/titanium dioxide with carbon nanotubes for efficient electrocatalytic hydrogen evolution

    Science.gov (United States)

    Valenti, Giovanni; Boni, Alessandro; Melchionna, Michele; Cargnello, Matteo; Nasi, Lucia; Bertoni, Giovanni; Gorte, Raymond J.; Marcaccio, Massimo; Rapino, Stefania; Bonchio, Marcella; Fornasiero, Paolo; Prato, Maurizio; Paolucci, Francesco

    2016-12-01

    Considering the depletion of fossil-fuel reserves and their negative environmental impact, new energy schemes must point towards alternative ecological processes. Efficient hydrogen evolution from water is one promising route towards a renewable energy economy and sustainable development. Here we show a tridimensional electrocatalytic interface, featuring a hierarchical, co-axial arrangement of a palladium/titanium dioxide layer on functionalized multi-walled carbon nanotubes. The resulting morphology leads to a merging of the conductive nanocarbon core with the active inorganic phase. A mechanistic synergy is envisioned by a cascade of catalytic events promoting water dissociation, hydride formation and hydrogen evolution. The nanohybrid exhibits a performance exceeding that of state-of-the-art electrocatalysts (turnover frequency of 15000 H2 per hour at 50 mV overpotential). The Tafel slope of ~130 mV per decade points to a rate-determining step comprised of water dissociation and formation of hydride. Comparative activities of the isolated components or their physical mixtures demonstrate that the good performance evolves from the synergistic hierarchical structure.

  4. Facile synthesis and magnetic study of Ni@polyamide 66 coaxial nanotube arrays

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xiaoru, E-mail: lixiaoruqdu@126.com; Yang, Chao; Han, Ping; Zhao, Qingpei; Song, Guojun, E-mail: songguojunqdu@126.com

    2016-12-01

    Ni@polyamide 66 (PA66) core/shell coaxial double-layer nanotube arrays have been prepared in the nanopores of anodic aluminum oxide templates (AAO). The shell of PA66 nanotubes were formed first and then served as templates to deposit Ni nanotubes used as the core. The morphology, structures of the obtained arrays were examined by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The formation of this unique coaxial nanotube structure was confirmed by SEM and TEM images and X-ray diffraction (XRD). We further explored the magnetic properties of the obtained coaxial nanotube arrays with vibrating sample magnetometer (VSM) and found that Ni@PA66 coaxial nanotubes exhibited higher remanence ratio than that of Ni nanotubes. These Ni@PA66 coaxial nanotubes are promising to be used as templates to fill in other materials. - Highlights: • Ni@PA66 coaxial nanotubes are prepared successfully with PA66 nanotubes obtained first and then Ni nanotubes were deposited in PA66 nanotubes. • The magnetic property of Ni@PA66 coaxial nanotubes is better than that of Ni nanotubes. • Ni@PA66 coaxial nanotubes can be used as templates to fill in other materials.

  5. Coaxial nanocable composed by imogolite and carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Ramírez, M.; González, R. I.; Munoz, F.; Valdivia, J. A.; Rogan, J.; Kiwi, M. [Departamento de Física, Facultad de Ciencias, Universidad de Chile, Casilla 653, Santiago, 7800024 (Chile); Centro para el Desarrollo de la Nanociencia y la Nanotecnología, CEDENNA, Avda. Ecuador 3493, Santiago, 9170124 (Chile)

    2015-12-31

    The discovery and development of Carbon Nanotubes (CNTs) at the beginning of the 1990s has driven a major part of solid state research. The electronic properties of the CNTs have generated a large number of ideas, as building coaxial nanocables. In this work we propose a possible type of such nanocables, which is formed by three nanostructures: two conducting CNTs, where one of them is covered by an insulator (an inorganic oxide nanotube: the imogolite aluminosilicate). The theoretical calculations were carried out using the density functional tight-binding formalism, by means of the DFTB+ code. This formalism allows to calculate the band structure, which compares favorably with DFT calculations, but with a significantly lower computational cost. As a first step, we reproduce the calculations of already published results, where the formation of a nanocable composed by one CNT and the imogolite as an insulator. Afterwards, we simulate the band structure for the proposed structure to study the feasibility of the coaxial nanocable. Finally, using classical MD simulations, we study the possible mechanisms of formation of these nanocables.

  6. Homogeneous CdTe quantum dots-carbon nanotubes heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, Kayo Oliveira [Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João del-Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, CEP 36301-160, São João del-Rei, MG (Brazil); Bettini, Jefferson [Laboratório Nacional de Nanotecnologia, Centro Nacional de Pesquisa em Energia e Materiais, CEP 13083-970, Campinas, SP (Brazil); Ferrari, Jefferson Luis [Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João del-Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, CEP 36301-160, São João del-Rei, MG (Brazil); Schiavon, Marco Antonio, E-mail: schiavon@ufsj.edu.br [Grupo de Pesquisa em Química de Materiais – (GPQM), Departamento de Ciências Naturais, Universidade Federal de São João del-Rei, Campus Dom Bosco, Praça Dom Helvécio, 74, CEP 36301-160, São João del-Rei, MG (Brazil)

    2015-01-15

    The development of homogeneous CdTe quantum dots-carbon nanotubes heterostructures based on electrostatic interactions has been investigated. We report a simple and reproducible non-covalent functionalization route that can be accomplished at room temperature, to prepare colloidal composites consisting of CdTe nanocrystals deposited onto multi-walled carbon nanotubes (MWCNTs) functionalized with a thin layer of polyelectrolytes by layer-by-layer technique. Specifically, physical adsorption of polyelectrolytes such as poly (4-styrene sulfonate) and poly (diallyldimethylammonium chloride) was used to deagglomerate and disperse MWCNTs, onto which we deposited CdTe quantum dots coated with mercaptopropionic acid (MPA), as surface ligand, via electrostatic interactions. Confirmation of the CdTe quantum dots/carbon nanotubes heterostructures was done by transmission and scanning electron microscopies (TEM and SEM), dynamic-light scattering (DLS) together with absorption, emission, Raman and infrared spectroscopies (UV–vis, PL, Raman and FT-IR). Almost complete quenching of the PL band of the CdTe quantum dots was observed after adsorption on the MWCNTs, presumably through efficient energy transfer process from photoexcited CdTe to MWCNTs. - Highlights: • Highly homogeneous CdTe-carbon nanotubes heterostructures were prepared. • Simple and reproducible non-covalent functionalization route. • CdTe nanocrystals homogeneously deposited onto multi-walled carbon nanotubes. • Efficient energy transfer process from photoexcited CdTe to MWCNTs.

  7. Coaxial PANI/TiN/PANI nanotube arrays for high-performance supercapacitor electrodes.

    Science.gov (United States)

    Peng, Xiang; Huo, Kaifu; Fu, Jijiang; Zhang, Xuming; Gao, Biao; Chu, Paul K

    2013-10-03

    Coaxial PANI/TiN/PANI nanotube arrays prepared by electrochemical polymerization of PANI on nanoporous TiN nanotube arrays exhibit a high specific capacitance of 242 mF cm(-2), excellent rate capability with the capacitance remaining at 69% when the current density is increased 50 times from 0.2 to 10 mA cm(-2), and a long cycling life with less than 0.005% decay per cycle.

  8. Synthesis of CuO/Co3O4 Coaxial Heterostructures for Efficient and Recycling Photodegradation

    Directory of Open Access Journals (Sweden)

    R. X. Chen

    2015-01-01

    Full Text Available The highly efficient CuO/Co3O4 composite photocatalyst with different morphologies has been synthesized directly on Cu wire mesh by controlling the composition of cobalt-containing solid precursors via a simple hydrothermal method. The structure morphology and composition of the composite photocatalyst have been characterized by scanning electron microscopy (SEM, transmission electron microscopy (TEM, X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, and UV-visible diffuse reflectance spectra. The photocatalytic result shows that the CuO/Co3O4 coaxial heterostructure is easy to recycle and exhibit enhanced photodegradation activity for methylene blue compared to single CuO nanorod arrays under full spectrum solar light irradiation. The enhanced photocatalytic efficiency of the composite could be ascribed to the synergistic effect of CuO and Co3O4. This study provides a general and effective method in the fabrication of 1D composition NRs with sound heterojunctions that show enhancement of photocatalytic performance and facility of recycling.

  9. All carbon coaxial supercapacitors based on hollow carbon nanotube sleeve structure

    Science.gov (United States)

    Zang, Xiaobei; Xu, Ruiqiao; Zhang, Yangyang; Li, Xinming; Zhang, Li; Wei, Jinquan; Wang, Kunlin; Zhu, Hongwei

    2015-01-01

    All carbon coaxial supercapacitors based on hollow carbon nanotube (CNT) sleeve structure are assembled and tested. The key advantage of the structure is that the inner core electrode is variable from CNT sleeve sponges, to CNT fibers, reduced graphene oxide fibers, and graphene woven fabrics. By changing core electrodes from sleeve sponges to CNT fibers, the electrochemical performance has been significantly enhanced. The capacitance based on sleeve sponge + CNT fiber double the capacitances of double-sleeve sponge supercapacitors thanks to reduction of the series and internal resistances. Besides, the coaxial sleeve structure possesses many other features, including high rate capacitance, long cycle life, and good flexibility.

  10. Coaxial Thermoplastic Elastomer-Wrapped Carbon Nanotube Fibers for Deformable and Wearable Strain Sensors

    KAUST Repository

    Zhou, Jian

    2018-01-22

    Highly conductive and stretchable fibers are crucial components of wearable electronics systems. Excellent electrical conductivity, stretchability, and wearability are required from such fibers. Existing technologies still display limited performances in these design requirements. Here, achieving highly stretchable and sensitive strain sensors by using a coaxial structure, prepared via coaxial wet spinning of thermoplastic elastomer-wrapped carbon nanotube fibers, is proposed. The sensors attain high sensitivity (with a gauge factor of 425 at 100% strain), high stretchability, and high linearity. They are also reproducible and durable. Their use as safe sensing components on deformable cable, expandable surfaces, and wearable textiles is demonstrated.

  11. Fabrication of Coaxial Si(1-x)Ge(x) Heterostructure Nanowires by O(2) Flow-Induced Bifurcate Reactions.

    Science.gov (United States)

    Kim, Ilsoo; Lee, Ki-Young; Kim, Ungkil; Park, Yong-Hee; Park, Tae-Eon; Choi, Heon-Jin

    2010-06-17

    We report on bifurcate reactions on the surface of well-aligned Si(1-x)Ge(x) nanowires that enable fabrication of two different coaxial heterostructure nanowires. The Si(1-x)Ge(x) nanowires were grown in a chemical vapor transport process using SiCl(4) gas and Ge powder as a source. After the growth of nanowires, SiCl(4) flow was terminated while O(2) gas flow was introduced under vacuum. On the surface of nanowires was deposited Ge by the vapor from the Ge powder or oxidized into SiO(2) by the O(2) gas. The transition from deposition to oxidation occurred abruptly at 2 torr of O(2) pressure without any intermediate region and enables selectively fabricated Ge/Si(1-x)Ge(x) or SiO(2)/Si(1-x)Ge(x) coaxial heterostructure nanowires. The rate of deposition and oxidation was dominated by interfacial reaction and diffusion of oxygen through the oxide layer, respectively.

  12. Fabrication of Coaxial Si1−xGex Heterostructure Nanowires by O2 Flow-Induced Bifurcate Reactions

    Science.gov (United States)

    2010-01-01

    We report on bifurcate reactions on the surface of well-aligned Si1−xGex nanowires that enable fabrication of two different coaxial heterostructure nanowires. The Si1−xGex nanowires were grown in a chemical vapor transport process using SiCl4 gas and Ge powder as a source. After the growth of nanowires, SiCl4 flow was terminated while O2 gas flow was introduced under vacuum. On the surface of nanowires was deposited Ge by the vapor from the Ge powder or oxidized into SiO2 by the O2 gas. The transition from deposition to oxidation occurred abruptly at 2 torr of O2 pressure without any intermediate region and enables selectively fabricated Ge/Si1−xGex or SiO2/Si1−xGex coaxial heterostructure nanowires. The rate of deposition and oxidation was dominated by interfacial reaction and diffusion of oxygen through the oxide layer, respectively. PMID:21076699

  13. Fabrication of Coaxial Si1−xGex Heterostructure Nanowires by O2 Flow-Induced Bifurcate Reactions

    Directory of Open Access Journals (Sweden)

    Kim Ilsoo

    2010-01-01

    Full Text Available Abstract We report on bifurcate reactions on the surface of well-aligned Si1−xGex nanowires that enable fabrication of two different coaxial heterostructure nanowires. The Si1−xGex nanowires were grown in a chemical vapor transport process using SiCl4 gas and Ge powder as a source. After the growth of nanowires, SiCl4 flow was terminated while O2 gas flow was introduced under vacuum. On the surface of nanowires was deposited Ge by the vapor from the Ge powder or oxidized into SiO2 by the O2 gas. The transition from deposition to oxidation occurred abruptly at 2 torr of O2 pressure without any intermediate region and enables selectively fabricated Ge/Si1−xGex or SiO2/Si1−xGex coaxial heterostructure nanowires. The rate of deposition and oxidation was dominated by interfacial reaction and diffusion of oxygen through the oxide layer, respectively.

  14. Augmented Photoelectrochemical Efficiency of ZnO/TiO2 Nanotube Heterostructures

    Science.gov (United States)

    Boda, Muzaffar Ahmad; Shah, Mohammad Ashraf

    2017-11-01

    ZnO/TiO2 nanotube heterostructures have been fabricated by electrodeposition of ZnO microcrystals over electrochemically anodized TiO2 nanotube arrays. The resulting ZnO/TiO2 nanotube heterostructures showed enhanced photocurrent density of 5.72 mA cm-2, about 1.5 times the value of 3.68 mA cm-2 shown by bare compact TiO2 nanotubes. This enhanced photocurrent density of the ZnO/TiO2 nanotube heterostructures is due to high electron mobility in the ZnO crystals, thereby decreasing the electron-hole recombination process, good interfacial quality between the ZnO and TiO2 structures, and a proposed smooth charge-transfer mechanism due to band bending at the interface. The morphological features of the as-prepared heterostructures were determined by field-emission scanning electron microscopy (FESEM). The crystallinity and phase purity of the samples were confirmed by x-ray diffraction (XRD) analysis. The light absorption properties of the prepared samples were investigated by ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). The photoelectrochemical efficiency of bare and ZnO-modified TiO2 nanotube heterostructures was determined by electrochemical analyzer.

  15. Poly(3-hexylthiophene)/multiwalled carbon hybrid coaxial nanotubes: nanoscale rectification and photovoltaic characteristics.

    Science.gov (United States)

    Kim, Kihyun; Shin, Ji Won; Lee, Yong Baek; Cho, Mi Yeon; Lee, Suk Ho; Park, Dong Hyuk; Jang, Dong Kyu; Lee, Cheol Jin; Joo, Jinsoo

    2010-07-27

    We fabricate hybrid coaxial nanotubes (NTs) of multiwalled carbon nanotubes (MWCNTs) coated with light-emitting poly(3-hexylthiophene) (P3HT). The p-type P3HT material with a thickness of approximately 20 nm is electrochemically deposited onto the surface of the MWCNT. The formation of hybrid coaxial NTs of the P3HT/MWCNT is confirmed by a transmission electron microscope, FT-IR, and Raman spectra. The optical and structural properties of the hybrid NTs are characterized using ultraviolet and visible absorption, Raman, and photoluminescence (PL) spectra where, it is shown that the PL intensity of the P3HT materials decreases after the hybridization with the MWCNTs. The current-voltage (I-V) characteristics of the outer P3HT single NT show the semiconducting behavior, while ohmic behavior is observed for the inner single MWCNT. The I-V characteristics of the hybrid junction between the outer P3HT NT and the inner MWCNT, for the hybrid single NT, exhibit the characteristics of a diode (i.e., rectification), whose efficiency is clearly enhanced with light irradiation. The rectification effect of the hybrid single NT has been analyzed in terms of charge tunneling models. The quasi-photovoltaic effect is also observed at low bias for the P3HT/MWCNT hybrid single NT.

  16. Rational design of coaxial mesoporous birnessite manganese dioxide/amorphous-carbon nanotubes arrays for advanced asymmetric supercapacitors

    KAUST Repository

    Zhu, Shijin

    2015-03-01

    Coaxial mesoporous MnO2/amorphous-carbon nanotubes have been synthesized via a facile and cost-effective strategy at room temperature. The coaxial double nanotubes of inner (outer) MnO2 and outer (inner) amorphous carbon can be obtained via fine tuning the preparative factors (e.g., deposition order and processing temperature). Furthermore, the electrochemical properties of the coaxial nanotubes were evaluated by cycle voltammetric (CV) and galvanostatic charge-discharge (GC) measurements. The as-prepared coaxial double nanotubes of outer MnO2 and inner amorphous carbon exhibit the optimized pseudocapacitance performance (362 F g-1) with good cycling stability, and ideal rate capability owning to the unique nanostructures. When assembled into two-electrode asymmetric supercapacitor, an energy density of 22.56 W h kg-1 at a power density of 224.9 W kg-1 is obtained. These findings provide a new and facile approach to fabricate high-performance electrode for supercapacitors.

  17. Single crystalline wurtzite ZnO/zinc blende ZnS coaxial heterojunctions and hollow zinc blende ZnS nanotubes: synthesis, structural characterization and optical properties.

    Science.gov (United States)

    Huang, Xing; Willinger, Marc-Georg; Fan, Hua; Xie, Zai-lai; Wang, Lei; Klein-Hoffmann, Achim; Girgsdies, Frank; Lee, Chun-Sing; Meng, Xiang-Min

    2014-08-07

    Synthesis of ZnO/ZnS heterostructures under thermodynamic conditions generally results in the wurtzite (WZ) structure of the ZnS component because its WZ phase is thermodynamically more stable than its zinc blende (ZB) phase. In this report, we demonstrate for the first time the preparation of ZnO/ZnS coaxial nanocables composed of single crystalline ZB structured ZnS epitaxially grown on WZ ZnO via a two-step thermal evaporation method. The deposition temperature is believed to play a crucial role in determining the crystalline phase of ZnS. Through a systematic structural analysis, the ZnO core and the ZnS shell are found to have an orientation relationship of (0002)ZnO(WZ)//(002)ZnS(ZB) and [01-10]ZnO(WZ)//[2-20]ZnS(ZB). Observation of the coaxial nanocables in cross-section reveals the formation of voids between the ZnO core and the ZnS shell during the coating process, which is probably associated with the nanoscale Kirkendall effect known to result in porosity. Furthermore, by immersing the ZnO/ZnS nanocable heterojunctions in an acetic acid solution to etch away the inner ZnO cores, single crystalline ZnS nanotubes orientated along the [001] direction of the ZB structure were also achieved for the first time. Finally, optical properties of the hollow ZnS tubes were investigated and discussed in detail. We believe that our study could provide some insights into the controlled fabrication of one dimensional (1D) semiconductors with desired morphology, structure and composition at the nanoscale, and the synthesized WZ ZnO/ZB ZnS nanocables as well as ZB ZnS nanotubes could be ideal candidates for the study of optoelectronics based on II-VI semiconductors.

  18. Winding aligned carbon nanotube composite yarns into coaxial fiber full batteries with high performances.

    Science.gov (United States)

    Weng, Wei; Sun, Qian; Zhang, Ye; Lin, Huijuan; Ren, Jing; Lu, Xin; Wang, Min; Peng, Huisheng

    2014-06-11

    Inspired by the fantastic and fast-growing wearable electronics such as Google Glass and Apple iWatch, matchable lightweight and weaveable energy storage systems are urgently demanded while remaining as a bottleneck in the whole technology. Fiber-shaped energy storage devices that can be woven into electronic textiles may represent a general and effective strategy to overcome the above difficulty. Here a coaxial fiber lithium-ion battery has been achieved by sequentially winding aligned carbon nanotube composite yarn cathode and anode onto a cotton fiber. Novel yarn structures are designed to enable a high performance with a linear energy density of 0.75 mWh cm(-1). A wearable energy storage textile is also produced with an areal energy density of 4.5 mWh cm(-2).

  19. Synthesis of Nanoscale Heterostructures Comprised of Metal Nanowires, Carbon Nanotubes, and Metal Nanoparticles: Investigation of Their Structure and Electrochemical Properties

    Directory of Open Access Journals (Sweden)

    Nitin Chopra

    2015-01-01

    Full Text Available One-dimensional nanoscale heterostructures comprised of multisegment gold-nickel nanowires, carbon nanotube, and nickel nanoparticles were fabricated in a unique approach combining top-down and bottom-up assembly methods. Porous alumina template was utilized for sequential electrodeposition of gold and nickel nanowire segments. This was followed by chemical vapor deposition growth of carbon nanotubes on multisegment gold-nickel nanowires, where nickel segment also acted as a carbon nanotube growth catalyst. The aligned arrays of these gold-nickel-carbon nanotube heterostructures were released from porous alumina template and then subjected to wet-chemical process to be decorated with nickel/nickel oxide core/shell nanoparticles. X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy were utilized for morphology, interface, defect, and structure characterization. The electrochemical performance of these heterostructures was studied using cyclic voltammetry method and the specific capacitance of various heterostructures was estimated and compared.

  20. High voltage generation from lead-free magnetoelectric coaxial nanotube arrays and their applications in nano energy harvesters

    Science.gov (United States)

    Lekha, C. S. Chitra; Kumar, Ajith S.; Vivek, S.; Rasi, U. P. Mohammed; Venkata Saravanan, K.; Nandakumar, K.; Nair, Swapna S.

    2017-02-01

    Harvesting energy from surrounding vibrations and developing self-powered portable devices for wireless and mobile electronics have recently become popular. Here the authors demonstrate the synthesis of piezoelectric energy harvesters based on nanotube arrays by a wet chemical route, which requires no sophisticated instruments. The energy harvester gives an output voltage of 400 mV. Harvesting energy from a sinusoidal magnetic field is another interesting phenomenon for which the authors fabricated a magnetoelectric energy harvester based on piezoelectric-magnetostrictive coaxial nanotube arrays. Piezoelectric K0.5Na0.5NbO3 (KNN) is fabricated as the shell and magnetostrictive CoFe2O4 (CFO) as the core of the composite coaxial nanotubes. The delivered voltages are as high as 300 mV at 500 Hz and at a weak ac magnetic field of 100 Oe. Further tailoring of the thickness of the piezoelectric and magnetic layers can enhance the output voltage by several orders. Easy, single-step wet chemical synthesis enhances the industrial upscaling potential of these nanotubes as energy harvesters. In view of the excellent properties reported here, the lead-free piezoelectric component (KNN) in this nanocomposite should be explored for eco-friendly piezoelectric as well as magnetoelectric power generators in nanoelectromechanical systems (NEMS).

  1. Chemical changes in carbon Nanotube-Nickel/Nickel Oxide Core/Shell nanoparticle heterostructures treated at high temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Chopra, Nitin, E-mail: nchopra@eng.ua.edu [Metallurgical and Materials Engineering, Center for Materials for Information Technology (MINT), Box 870202, University of Alabama, Tuscaloosa, AL 35487 (United States); McWhinney, Hylton G. [Prairie View A and M University, TX 77446 (United States); Shi Wenwu [Metallurgical and Materials Engineering, Center for Materials for Information Technology (MINT), Box 870202, University of Alabama, Tuscaloosa, AL 35487 (United States)

    2011-06-15

    Heterostructures composed of carbon nanotube (CNT) coated with Ni/NiO core/shell nanoparticles (denoted as CNC heterostructures) were synthesized in a wet-chemistry and single-step synthesis route involving direct nucleation of nanoparticles on CNT surface. Two different aspects of CNC heterostructures were studied here. First, it was observed that the nanoparticle coatings were more uniform on the as-produced and non-purified CNTs compared to purified (or acid treated) CNTs. These heterostructures were characterized using electron microscopy, Raman spectroscopy, and energy dispersive spectroscopy. Second, thermal stability of CNC heterostructures was studied by annealing them in N{sub 2}-rich (O{sub 2}-lean) environment between 125 and 750 deg. C for 1 h. A detailed X-ray photoelectron spectroscopy and Raman spectroscopy analysis was performed to evaluate the effects of annealing temperatures on chemical composition, phases, and stability of the heterostructures. It was observed that the CNTs present in the heterostructures completely decomposed and core Ni nanoparticle oxidized significantly between 600 and 750 deg. C. - Research Highlights: {yields} Heterostructures composed of CNTs coated with Ni/NiO core/shell nanoparticles. {yields} Poor nanoparticle coverage on purified CNT surface compared to non-purified CNTs. {yields} CNTs in heterostructures decompose between 600 and 750 deg. C in N{sub 2}-rich atmosphere. {yields} Metallic species in heterostructures were oxidized at higher temperatures.

  2. White Electroluminescence Using ZnO Nanotubes/GaN Heterostructure Light-Emitting Diode

    Directory of Open Access Journals (Sweden)

    Sadaf JR

    2010-01-01

    Full Text Available Abstract We report the fabrication of heterostructure white light–emitting diode (LED comprised of n-ZnO nanotubes (NTs aqueous chemically synthesized on p-GaN substrate. Room temperature electroluminescence (EL of the LED demonstrates strong broadband white emission spectrum consisting of predominating peak centred at 560 nm and relatively weak violet–blue emission peak at 450 nm under forward bias. The broadband EL emission covering the whole visible spectrum has been attributed to the large surface area and high surface states of ZnO NTs produced during the etching process. In addition, comparison of the EL emission colour quality shows that ZnO nanotubes have much better quality than that of the ZnO nanorods. The colour-rendering index of the white light obtained from the nanotubes was 87, while the nanorods-based LED emit yellowish colour.

  3. White Electroluminescence Using ZnO Nanotubes/GaN Heterostructure Light-Emitting Diode.

    Science.gov (United States)

    Sadaf, J R; Israr, Mq; Kishwar, S; Nur, O; Willander, M

    2010-04-04

    We report the fabrication of heterostructure white light-emitting diode (LED) comprised of n-ZnO nanotubes (NTs) aqueous chemically synthesized on p-GaN substrate. Room temperature electroluminescence (EL) of the LED demonstrates strong broadband white emission spectrum consisting of predominating peak centred at 560 nm and relatively weak violet-blue emission peak at 450 nm under forward bias. The broadband EL emission covering the whole visible spectrum has been attributed to the large surface area and high surface states of ZnO NTs produced during the etching process. In addition, comparison of the EL emission colour quality shows that ZnO nanotubes have much better quality than that of the ZnO nanorods. The colour-rendering index of the white light obtained from the nanotubes was 87, while the nanorods-based LED emit yellowish colour.

  4. Si/Ge hetero-structure nanotube tunnel field effect transistor

    KAUST Repository

    Hanna, A. N.

    2015-01-07

    We discuss the physics of conventional channel material (silicon/germanium hetero-structure) based transistor topology mainly core/shell (inner/outer) gated nanotube vs. gate-all-around nanowire architecture for tunnel field effect transistor application. We show that nanotube topology can result in higher performance through higher normalized current when compared to nanowire architecture at Vdd-=-1-V due to the availability of larger tunneling cross section and lower Shockley-Reed-Hall recombination. Both architectures are able to achieve sub 60-mV/dec performance for more than five orders of magnitude of drain current. This enables the nanotube configuration achieving performance same as the nanowire architecture even when Vdd is scaled down to 0.5-V.

  5. Synthesis of coaxial nanotubes of polyaniline and poly(hydroxyethyl methacrylate by oxidative/initiated chemical vapor deposition

    Directory of Open Access Journals (Sweden)

    Alper Balkan

    2017-04-01

    Full Text Available Vapor-phase synthesis techniques of polymeric nanostructures offer unique advantages over conventional, solution-based techniques because of their solventless nature. In this work, we report the fabrication of coaxial polymer nanotubes using two different chemical vapor deposition methods. The fabrication process involves the deposition of an outer layer of the conductive polyaniline (PANI by oxidative chemical vapor deposition, followed by the deposition of the inner layer of poly(2-hydroxyethyl methacrylate (pHEMA hydrogel by initiated chemical vapor deposition. The vapor-phase techniques allowed for fine-tuning of the thickness of the individual layers, keeping the functionalities of the polymers intact. The response of the single components and the coaxial nanotubes to changes in humidity was investigated for potential humidity sensor applications. For single-component conductive PANI nanotubes, the resistance changed parabolically with relative humidity because of competing effects of doping and swelling of the PANI polymer under humid conditions. Introducing a hydrogel inner layer increased the overall resistance, and enhanced swelling, which caused the resistance to continuously increase with relative humidity.

  6. Synthesis of coaxial nanotubes of polyaniline and poly(hydroxyethyl methacrylate) by oxidative/initiated chemical vapor deposition.

    Science.gov (United States)

    Balkan, Alper; Armagan, Efe; Ozaydin Ince, Gozde

    2017-01-01

    Vapor-phase synthesis techniques of polymeric nanostructures offer unique advantages over conventional, solution-based techniques because of their solventless nature. In this work, we report the fabrication of coaxial polymer nanotubes using two different chemical vapor deposition methods. The fabrication process involves the deposition of an outer layer of the conductive polyaniline (PANI) by oxidative chemical vapor deposition, followed by the deposition of the inner layer of poly(2-hydroxyethyl methacrylate) (pHEMA) hydrogel by initiated chemical vapor deposition. The vapor-phase techniques allowed for fine-tuning of the thickness of the individual layers, keeping the functionalities of the polymers intact. The response of the single components and the coaxial nanotubes to changes in humidity was investigated for potential humidity sensor applications. For single-component conductive PANI nanotubes, the resistance changed parabolically with relative humidity because of competing effects of doping and swelling of the PANI polymer under humid conditions. Introducing a hydrogel inner layer increased the overall resistance, and enhanced swelling, which caused the resistance to continuously increase with relative humidity.

  7. Gallium-assisted growth of flute-like MgO nanotubes, Ga2O3-filled MgO nanotubes, and MgO/Ga2O3 co-axial nanotubes.

    Science.gov (United States)

    Jie, Jiansheng; Wu, Chunyan; Yu, Yongqiang; Wang, Li; Hu, Zhizhong

    2009-02-18

    Flute-like MgO nanotubes were successfully synthesized via a simple thermal evaporation method by using Mg(3)N(2) and Ga(2)O(3) as the source materials. The nanotubes are single-crystal cubic MgO, and have [100] orientation. In contrast to conventional nanotubes with intact walls, the flute-like MgO nanotubes possess a unique porous structure. On the nanotubes there are series of holes aligned along the nanotube length with approximate equidistance. Ga(2)O(3)-filled MgO nanotubes and MgO/Ga(2)O(3) co-axial nanotubes were also found in the product. Further investigation confirms that the inner beta-Ga(2)O(3) has an epitaxial growth relation with the outer MgO nanotube due to their perfect lattice matching. A gallium-assisted growth mechanism was proposed to interpret the growth of the flute-like MgO nanotubes. The thermal expansion and evaporation of the filled liquid gallium in MgO nanotubes are likely responsible for the formation of the hole structures on the side walls.

  8. Inkjet printed ambipolar transistors and inverters based on carbon nanotube/zinc tin oxide heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Bongjun; Jang, Seonpil; Dodabalapur, Ananth, E-mail: ananth.dodabalapur@engr.utexas.edu [Microelectronics Research Center, The University of Texas at Austin, Austin, Texas 78758 (United States); Department of Electrical and Computer Engineering, The University of Texas at Austin, Austin, Texas 78712 (United States); Geier, Michael L.; Prabhumirashi, Pradyumna L. [Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois 60208 (United States); Hersam, Mark C. [Department of Materials Science and Engineering, Northwestern University, Evanston, Illinois 60208 (United States); Department of Chemistry, Northwestern University, Evanston, Illinois 60208 (United States); Department of Medicine, Northwestern University, Evanston, Illinois 60208 (United States)

    2014-02-10

    We report ambipolar field-effect transistors (FETs) consisting of inkjet printed semiconductor bilayer heterostructures utilizing semiconducting single-walled carbon nanotubes (SWCNTs) and amorphous zinc tin oxide (ZTO). The bilayer structure allows for electron transport to occur principally in the amorphous oxide layer and hole transport to occur exclusively in the SWCNT layer. This results in balanced electron and hole mobilities exceeding 2 cm{sup 2} V{sup −1} s{sup −1} at low operating voltages (<5 V) in air. We further show that the SWCNT-ZTO hybrid ambipolar FETs can be integrated into functional inverter circuits that display high peak gain (>10). This work provides a pathway for realizing solution processable, inkjet printable, large area electronic devices, and systems based on SWCNT-amorphous oxide heterostructures.

  9. Sub-10-nm intracellular bioelectronic probes from nanowire-nanotube heterostructures.

    Science.gov (United States)

    Fu, Tian-Ming; Duan, Xiaojie; Jiang, Zhe; Dai, Xiaochuan; Xie, Ping; Cheng, Zengguang; Lieber, Charles M

    2014-01-28

    The miniaturization of bioelectronic intracellular probes with a wide dynamic frequency range can open up opportunities to study biological structures inaccessible by existing methods in a minimally invasive manner. Here, we report the design, fabrication, and demonstration of intracellular bioelectronic devices with probe sizes less than 10 nm. The devices are based on a nanowire-nanotube heterostructure in which a nanowire field-effect transistor detector is synthetically integrated with a nanotube cellular probe. Sub-10-nm nanotube probes were realized by a two-step selective etching approach that reduces the diameter of the nanotube free-end while maintaining a larger diameter at the nanowire detector necessary for mechanical strength and electrical sensitivity. Quasi-static water-gate measurements demonstrated selective device response to solution inside the nanotube, and pulsed measurements together with numerical simulations confirmed the capability to record fast electrophysiological signals. Systematic studies of the probe bandwidth in different ionic concentration solutions revealed the underlying mechanism governing the time response. In addition, the bandwidth effect of phospholipid coatings, which are important for intracellular recording, was investigated and modeled. The robustness of these sub-10-nm bioelectronics probes for intracellular interrogation was verified by optical imaging and recording the transmembrane resting potential of HL-1 cells. These ultrasmall bioelectronic probes enable direct detection of cellular electrical activity with highest spatial resolution achieved to date, and with further integration into larger chip arrays could provide a unique platform for ultra-high-resolution mapping of activity in neural networks and other systems.

  10. Processing and Characterization of SrTiO₃-TiO₂ Nanoparticle-Nanotube Heterostructures on Titanium for Biomedical Applications.

    Science.gov (United States)

    Wang, Yu; Zhang, Dongmei; Wen, Cuie; Li, Yuncang

    2015-07-29

    Surface properties such as physicochemical characteristics and topographical parameters of biomaterials, essentially determining the interaction between the biological cells and the biomaterial, are important considerations in the design of implant materials. In this study, a layer of SrTiO3-TiO2 nanoparticle-nanotube heterostructures on titanium has been fabricated via anodization combined with a hydrothermal process. Titanium was anodized to create a layer of titania (TiO2) nanotubes (TNTs), which was then decorated with a layer of SrTiO3 nanoparticles via hydrothermal processing. SrTiO3-TiO2 heterostructures with high and low volume fraction of SrTiO3 nanoparticle (denoted by 6.3-Sr/TNTs and 1.4-Sr/TNTs) were achieved by using a hydrothermal processing time of 12 and 3 h, respectively. The in vitro biocompatibility of the SrTiO3-TiO2 heterostructures was assessed by using osteoblast cells (SaOS2). Our results indicated that the SrTiO3-TiO2 heterostructures with different volume fractions of SrTiO3 nanoparticles exhibited different Sr ion release in cell culture media and different surface energies. An appropriate volume fraction of SrTiO3 in the heterostructures stimulated the secretion of cell filopodia, leading to enhanced biocompatibility in terms of cell attachment, anchoring, and proliferation on the heterostructure surface.

  11. Conductive cable fibers with insulating surface prepared by co-axial electrospinning of multi-walled nanotubes and cellulose

    Science.gov (United States)

    Miyauchi, Minoru; Miao, Jianjun; Simmons, Trevor J.; Lee, Jong-Won; Doherty, Thomas V.; Dordick, Jonathan S.; Linhardt, Robert J.

    2010-01-01

    A core-sheath of multi-walled carbon nanotube (MWNT)-cellulose fibers of diameters from several hundreds nm to several µm were prepared by co-axial electrospinning from a non-valatile, non-flammable ionic liquid (IL) solvent, 1-methyl-3-methylimidazolium acetate ([EMIM][Ac]). MWNTs were dispersed in IL to form a gel solution. This gel core solution was electrospun surrounded by a sheath solution of cellulose disolved in the same IL. Electrospun fibers were collected in a coagulation bath containing ethanol-water to completely remove the IL and dried to form a core-sheath MWNT-cellulose fibers having a cable structure with a conductive core and insulating sheath. Enzymatic treatment of a portion of a mat of these fibers with cellulase selectively removed the cellulose sheath exposing the MWNT core for connection to an electrode. These MWNT-cellulose fiber mats demonstrated excellent conductivity due to a conductive pathway of bundleled MWNTs. Fiber mat conductivity increased with increasing ratio of MWNT in the fibers with a maximum conductivity of 10.7 S/m obtained at 45 wt% MWNT loading. PMID:20690644

  12. Formation of Coaxial Nanocables with Amplified Supramolecular Chirality through an Interaction between Carbon Nanotubes and a Chiral π-Gelator.

    Science.gov (United States)

    Vedhanarayanan, Balaraman; Nair, Vishnu S; Nair, Vijayakumar C; Ajayaghosh, Ayyappanpillai

    2016-08-22

    In an attempt to gather experimental evidence for the influence of carbon allotropes on supramolecular chirality, we found that carbon nanotubes (CNTs) facilitate amplification of the molecular chirality of a π-gelator (MC-OPV) to supramolecular helicity at a concentration much lower than that required for intermolecular interaction. For example, at a concentration 1.8×10(-4)  m, MC-OPV did not exhibit a CD signal; however, the addition of 0-0.6 mg of SWNTs resulted in amplified chirality as evident from the CD spectrum. Surprisingly, AFM analysis revealed the formation of thick helical fibers with a width of more than 100 nm. High-resolution TEM analysis and solid-state UV/Vis/NIR spectroscopy revealed that the thick helical fibers were cylindrical cables composed of individually wrapped and coaxially aligned SWNTs. Such an impressive effect of CNTs on supramolecular chirality and cylindrical-cable formation has not been reported previously. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Electrical injection in longitudinal and coaxial heterostructure nanowires: a comparative study through a three-dimensional simulation.

    Science.gov (United States)

    Li, D; Ning, C Z

    2008-12-01

    We carried out a comparative study of electrical injection in longitudinal p-i-n and coaxial p-n core-shell nanowires by performing a three-dimensional numerical simulation. In the case of the core-shell structure, we show that both electrons and holes of high density can be efficiently injected into and confined in the structure even without an i-region. The required bias voltage and doping concentrations in the core-shell structure are smaller than those in the longitudinal p-i-n structure to achieve the same carrier injection level. Furthermore, we show that a type-I band alignment, as required in traditional p-i-n structure is not necessary in core-shell structure, allowing more flexibility in nanowire devices design. Our results thus provide a theoretical foundation and understanding that a core-shell structure is far superior to the longitudinal p-i-n structure for electrical injection nanowire lasers.

  14. NiO@ZnO heterostructured nanotubes: coelectrospinning fabrication, characterization, and highly enhanced gas sensing properties.

    Science.gov (United States)

    Xu, Lin; Zheng, Ruifang; Liu, Shuhai; Song, Jian; Chen, Jiansheng; Dong, Biao; Song, Hongwei

    2012-07-16

    Novel NiO@ZnO heterostructured nanotubes (NTs) were fabricated by the coelectrospinning method, consisting of external hexagonal ZnO shell and internal cubic NiO NTs. They are carefully investigated by scanning electron microscopy, transmission electron microscopy, scanning transmission electron microscopy, energy-dispersive X-ray spectroscopy mapping, X-ray diffraction, and X-ray photoelectron spectroscopy techniques. A reasonable formation mechanism of the hierarchical NiO@ZnO NTs is proposed, which is discussed from the view of degradation temperature of different polymers and the amount of inorganic salts. They were then explored for fabrication of H(2)S gas sensors. The gas sensing test reveals that compared with the pure ZnO, NiO, and the ZnO-NiO mixed gas sensors, hierarchical gas sensor exhibits highly improved sensing performances to dilute hydrogen sulfide (H(2)S) gas. The response of the optimum NiO@ZnO NTs sensor to 50 ppm H(2)S increases as high as 2.7-23.7 times compared to the other sensors, whereas the response and recovery times also become shorter considerably. These enhanced gas sensing properties are closely related to the change of nanostructure and activity of ZnO and NiO nanocrystals as well as combination of homo- and heterointerfaces in the optimum gas sensor, which are confirmed by a series of well-designed experiments.

  15. Gas-Phase Growth of Heterostructures of Carbon Nanotubes and Bimetallic Nanowires

    Directory of Open Access Journals (Sweden)

    Whi Dong Kim

    2011-01-01

    Full Text Available A simple, inexpensive, and viable method for growing multiple heterostructured carbon nanotubes (CNTs over the entire surface of Ni-Al bimetallic nanowires (NWs in the gas phase was developed. Polymer-templated bimetallic nitrate NWs were produced by electrospinning in the first step, and subsequent calcination resulted in the formation of bimetallic oxide NWs by thermal decomposition. In the second step, free-floating bimetallic NWs were produced by spray pyrolysis in an environment containing hydrogen gas as a reducing gas. These NWs were continuously introduced into a thermal CVD reactor in order to grow CNTs in the gas phase. Scanning electron microscopy (SEM, transmission electron microscopy (TEM, and Raman spectrometry analyses revealed that the catalytic Ni sites exposed in the non-catalytic Al matrix over the entire surface of the bimetallic NWs were seeded to radially grow highly graphitized CNTs, which resembled “foxtail” structures. The grown CNTs were found to have a relatively uniform diameter of approximately 10±2 nm and 10 to 15 walls with a hollow core. The average length of the gas-phase-grown CNTs can be controlled between 100 and 1000 nm by adjusting the residence time of the free-floating bimetallic NWs in the thermal CVD reactor.

  16. Visible-light-driven photoelectrochemical and photocatalytic performances of Cr-doped SrTiO3/TiO2 heterostructured nanotube arrays

    OpenAIRE

    Zhengbo Jiao; Tao Chen; Jinyan Xiong; Teng Wang; Gongxuan Lu; Jinhua Ye; Yingpu Bi

    2013-01-01

    Well-aligned TiO2 nanotube arrays have become of increasing significance because of their unique highly ordered array structure, high specific surface area, unidirectional charge transfer and transportation features. However, their poor visible light utilization as well as the high recombination rate of photoexcited electron-hole pairs greatly limited their practical applications. Herein, we demonstrate the fabrication of visible-light-responsive heterostructured Cr-doped SrTiO3/TiO2 nanotube...

  17. Synthesis of coaxial nanotubes of MoS{sub 2} and carbon; Sintesis de nanotubos coaxiales de MoS{sub 2} y Carbono

    Energy Technology Data Exchange (ETDEWEB)

    Reza, C.; Perez, M.; Santiago, P. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    2002-07-01

    The di chalcogenides WS{sub 2} and MoS{sub 2} by their tubular properties were combined. It was synthesized coaxial structures of MoS{sub 2} with C with the purpose to studying the possible structural changes of the MoS{sub 2} nano tubes at was submitted to a propylene gas flux as carbon precursor in a thermal treatment. Studies of structural characterization by Transmission Electron Microscopy (Tem) were realized. The theoretical simulation of the structure was realized using an algorithm type multilayer. The possibility of the nano tubes are applied to gas storage as can be the hydrogen arouse interest by the energy production. (Author)

  18. The Tunable Hybrid Surface Phonon and Plasmon Polariton Modes in Boron Nitride Nanotube and Graphene Monolayer Heterostructures

    CERN Document Server

    Sun, Yu; Cheng, Jiangtao; Liu, Jiansheng

    2014-01-01

    The hybrid modes incorporating surface phonon polariton (SPhP) modes in boron nitride nanotubes (BNNTs) and surface plasmon polariton (SPP) modes in graphene monolayers are theoretically studied. The combination of the 1D BNNTs and 2D graphene monolayer further improves the modal characteristics with electrical tunability. Superior to the graphene monolayers, the proposed heterostructures supports single mode transmission with lateral optical confinement. The modal characteristics can be shifted from SPP-like toward SPhP-like. Both the figure of merit and field enhancement of hybrid modes are improved over 3 times than those of BNNT SPhP modes, which may further enable sub-wavelength mid-infrared applications.

  19. Langmuir-Blodgett assembly of visible light responsive TiO2 nanotube arrays/graphene oxide heterostructure

    Science.gov (United States)

    Chen, Ying; Gao, Hongyan; Wei, Danming; Dong, Xinju; Cao, Yan

    2017-01-01

    The hybrid nanocomposites of titanium dioxide (TiO2) with graphene oxide (GO) have recently garnered much attention as electronic devices, energy conversion devices, photocatalysts and other applications. In this study, Langmuir-Blodgett (LB) assembly method was firstly reported to prepare a TiO2 nanotube arrays (TNA)-GO heterostructure. The as-prepared TNA-GO sample was characterized by X-ray diffraction, Raman spectra, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. The promising characteristics of this TNA-GO material, the inexpensive, nontoxic and highly visible-light responsiveness, may raise the potential uses in many, various photocatalytic applications.

  20. Self-Assembled Hierarchical Interfaces of ZnO Nanotubes/Graphene Heterostructures for Efficient Room Temperature Hydrogen Sensors.

    Science.gov (United States)

    Kathiravan, Deepa; Huang, Bohr-Ran; Saravanan, Adhimoorthy

    2017-04-05

    Herein, we report the novel nanostructural interfaces of self-assembled hierarchical ZnO nanotubes/graphene (ZNT/G) with three different growing times of ZNTs on graphene substrates (namely, SH1, SH2, and SH3). Each sample was fabricated with interdigitated electrodes to form hydrogen sensors, and their hydrogen sensing properties were comprehensively studied. The systematic investigation revealed that SH1 sensor exhibits an ultrahigh sensor response even at a low detection level of 10 ppm (14.3%) to 100 ppm (28.1%) compared to those of the SH2 and SH3 sensors. The SH1 sensor was also found to be well-retained with repeatability, reliability, and long-term stability of 90 days under hydrogenation/dehydrogenation processes. This outstanding enhancement in sensing properties of SH1 is attributed to the formation of a strong metalized region in the ZNT/G interface due to the inner/outer surfaces of ZNTs, establishing a multiple depletion layer. Furthermore, the respective band models of each nanostructure were also purposed to describe their heterostructure, which illustrates the hydrogen sensing properties. Moreover, the long-term stability can be ascribed by the heterostructured combination of ZNTs and graphene via a spillover effect. The salient features of this self-assembled nanostructure are its reliability, simple synthesis method, and long-term stability, which makes it a promising candidate for new generation hydrogen sensors and hydrogen storage materials.

  1. Langmuir-Blodgett assembly of visible light responsive TiO{sub 2} nanotube arrays/graphene oxide heterostructure

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Ying; Gao, Hongyan; Wei, Danming; Dong, Xinju; Cao, Yan, E-mail: yan.cao@wku.edu

    2017-01-15

    Highlights: • First to report a heterostructure of TNA with GO prepared by LB assembly. • Much better photocurrent (32 μAcm{sup −2}) of TNA-GO, contrasting to TNA (12 μAcm{sup −2}). • Schottky junction formed between TNA and GO enhanced the photocurrent. • GO on TNA improved the hydrophilicity of TNA-GO. - Abstract: The hybrid nanocomposites of titanium dioxide (TiO{sub 2}) with graphene oxide (GO) have recently garnered much attention as electronic devices, energy conversion devices, photocatalysts and other applications. In this study, Langmuir-Blodgett (LB) assembly method was firstly reported to prepare a TiO{sub 2} nanotube arrays (TNA)-GO heterostructure. The as-prepared TNA-GO sample was characterized by X-ray diffraction, Raman spectra, scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. The promising characteristics of this TNA-GO material, the inexpensive, nontoxic and highly visible-light responsiveness, may raise the potential uses in many, various photocatalytic applications.

  2. Wrapping Aligned Carbon Nanotube Composite Sheets around Vanadium Nitride Nanowire Arrays for Asymmetric Coaxial Fiber-Shaped Supercapacitors with Ultrahigh Energy Density.

    Science.gov (United States)

    Zhang, Qichong; Wang, Xiaona; Pan, Zhenghui; Sun, Juan; Zhao, Jingxin; Zhang, Jun; Zhang, Cuixia; Tang, Lei; Luo, Jie; Song, Bin; Zhang, Zengxing; Lu, Weibang; Li, Qingwen; Zhang, Yuegang; Yao, Yagang

    2017-04-12

    The emergence of fiber-shaped supercapacitors (FSSs) has led to a revolution in portable and wearable electronic devices. However, obtaining high energy density FSSs for practical applications is still a key challenge. This article exhibits a facile and effective approach to directly grow well-aligned three-dimensional vanadium nitride (VN) nanowire arrays (NWAs) on carbon nanotube (CNT) fiber with an ultrahigh specific capacitance of 715 mF/cm(2) in a three-electrode system. Benefiting from their intriguing structural features, we successfully fabricated a prototype asymmetric coaxial FSS (ACFSS) with a maximum operating voltage of 1.8 V. From core to shell, this ACFSS consists of a CNT fiber core coated with VN@C NWAs as the negative electrode, Na2SO4 poly(vinyl alcohol) (PVA) as the solid electrolyte, and MnO2/conducting polymer/CNT sheets as the positive electrode. The novel coaxial architecture not only fully enables utilization of the effective surface area and decreases the contact resistance between the two electrodes but also, more importantly, provides a short pathway for the ultrafast transport of axial electrons and ions. The electrochemical results show that the optimized ACFSS exhibits a remarkable specific capacitance of 213.5 mF/cm(2) and an exceptional energy density of 96.07 μWh/cm(2), the highest areal capacitance and areal energy density yet reported in FSSs. Furthermore, the device possesses excellent flexibility in that its capacitance retention reaches 96.8% after bending 5000 times, which further allows it to be woven into flexible electronic clothes with conventional weaving techniques. Therefore, the asymmetric coaxial architectural design allows new opportunities to fabricate high-performance flexible FSSs for future portable and wearable electronic devices.

  3. In Situ Reactive Synthesis of Polypyrrole-MnO2 Coaxial Nanotubes as Sulfur Hosts for High-Performance Lithium-Sulfur Battery.

    Science.gov (United States)

    Zhang, Jun; Shi, Ye; Ding, Yu; Zhang, Wenkui; Yu, Guihua

    2016-11-09

    Lithium-sulfur batteries are considered as a promising candidate for high energy density storage applications. However, their specific capacity and cyclic stability are hindered by poor conductivity of sulfur and the dissolution of redox intermediates. Here, we design polypyrrole-MnO2 coaxial nanotubes to encapsulate sulfur, in which MnO2 restrains the shuttle effect of polysulfides greatly through chemisorption and polypyrrole serves as conductive frameworks. The polypyrrole-MnO2 nanotubes are synthesized through in situ polymerization of pyrrole using MnO2 nanowires as both template and oxidization initiator. A stable Coulombic efficiency of ∼98.6% and a decay rate of 0.07% per cycle along with 500 cycles at 1C-rate are achieved for S/PPy-MnO2 ternary electrodes with 70 wt % of S and 5 wt % of MnO2. The excellent trapping ability of MnO2 to polysulfides and tubular structure of polypyrrole with good flexibility and conductivity are responsible for the significantly improved cyclic stability and rate capability.

  4. Enhanced photoelectrocatalytic performance of heterostructured TiO2-based nanoparticles decorated nanotubes

    Science.gov (United States)

    Wu, Liangpeng; Yang, Xu; Huang, Yanqin; Li, Xinjun

    2017-06-01

    Titanium oxide nanotubes were prepared by hydrothermal treatment of TiO2 powder in NaOH aqueous solution and subsequently calcined. Titanium oxide nanotubes were further decorated by TiO2 nanoparticles through in situ hydrolysis of titanium isopropoxide containing alcohol and ammonia in an aqueous medium to form the composite catalyst (TNP/TiO2NTs). The morphology and structure of TNP/TiO2NTs were characterized by scanning and transmission electron microscopy, X-ray diffraction, UV-Vis, and Raman spectra. The separation efficiency of photo-excited carriers was investigated by photoluminescence technique and photoelectrochemical behavior. The photocatalytic activity was evaluated by the photocatalytic degradation of methyl orange. Due to the synergy effect caused by the interaction of titanium oxide nanotubes and TiO2 nanoparticles, the TNP/TiO2NTs composite shows efficient photogenerated carriers' separation and the increased light absorption. The photocatalytic activity was enhanced.

  5. Construction of a Hierarchical NiCo2S4@PPy Core-Shell Heterostructure Nanotube Array on Ni Foam for a High-Performance Asymmetric Supercapacitor.

    Science.gov (United States)

    Yan, Minglei; Yao, Yadong; Wen, Jiqiu; Long, Lu; Kong, Menglai; Zhang, Guanggao; Liao, Xiaoming; Yin, Guangfu; Huang, Zhongbing

    2016-09-21

    In this paper, a hierarchical NiCo2S4@polypyrrole core-shell heterostructure nanotube array on Ni foam (NiCo2S4@PPy/NF) was successfully developed as a bind-free electrode for supercapacitors. NiCo2S4@PPy-50/NF obtained under 50 s PPy electrodeposition shows a low charge-transfer resistance (0.31 Ω) and a high area specific capacitance of 9.781 F/cm(2) at a current density of 5 mA/cm(2), which is two times higher than that of pristine NiCo2S4/NF (4.255 F/cm(2)). Furthermore, an asymmetric supercapacitor was assembled using NiCo2S4@PPy-50/NF as positive electrode and activated carbon (AC) as negative electrode. The resulting NiCo2S4@PPy-50/NF//AC device exhibits a high energy density of 34.62 Wh/kg at a power density of 120.19 W/kg with good cycling performance (80.64% of the initial capacitance retention at 50 mA/cm(2) over 2500 cycles). The superior electrochemical performance can be attributed to the combined contribution of both component and unique core-shell heterostructure. The results demonstrate that the NiCo2S4@PPy-50 core-shell heterostructure nanotube array is promising as electrode material for supercapacitors in energy storage.

  6. When Layered Nickel-Cobalt Silicate Hydroxide Nanosheets Meet Carbon Nanotubes: A Synergetic Coaxial Nanocable Structure for Enhanced Electrocatalytic Water Oxidation.

    Science.gov (United States)

    Qiu, Ce; Jiang, Jing; Ai, Lunhong

    2016-01-13

    Developing robust earth-abundant electrocatalysts for oxygen evolution reaction (OER) is an ongoing scientific challenge, which is coupled with a number of important electrochemical processes and many key renewable energy systems, such as water splitting, rechargeable metal-air batteries, and regenerative fuel cells. Here, we proposed a rational design and fabrication of the synergetic coaxial nanocable structures by intimate growth of the layered nickel-cobalt silicate hydroxide nanosheets on the outer surfaces of multiwalled carbon nanotubes (MWCNTs@NCS) and demonstrated their high efficiency in electrocatalytic OER from water splitting. The electrocatalytic activities of the MWCNTs@NCS were found to be significantly higher than that of bare NCS and pristine MWCNTs, synergetically determining by such the constituted individual components. Among them, the MWCNTs@NCS-2 exhibited best electrocatalytic OER performance, showing a small OER onset potential, large anodic current and long-term durability, which was favorably comparable to the previously reported NiCo-based OER electrocatalysts in alkaline electrolytes. To the best of our knowledge, this was a first example on the earth-abundant metal silicate hydroxides utilized in electrochemical water splitting.

  7. Si nanotubes as an efficient electrode material for ZnO-based hetero-structure LEDs

    Science.gov (United States)

    Mashayekhi, Alireza; Sanaee, Zeinab; Sadeghipari, Mehrnoosh; Mohajerzadeh, Shamsoddin

    2016-12-01

    Silicon in the forms of nanotube (NT), nanowire (NW), and bulk were used as the p-type electrode for zinc-oxide NWs on Si heterojunction light emitting diodes (LED). The LEDs were fabricated by direct contact between p-type Si and n-type ZnO NWs. The results show that using Si NTs leads to a significant improvement in their LED performance including considerably lower turn-on voltage, smaller series resistance, higher rectification ratio, and stronger light intensity. Using this electrode, an excellent rectifying diode behavior was obtained with a turn-on voltage of 0.6 V and a rectification ratio of 15 at 5 V. This study proposes Si NTs as a promising electrode material for the fabrication of ZnO-based heterojunction LEDs.

  8. Sensitive electrochemical sensing for polycyclic aromatic amines based on a novel core–shell multiwalled carbon nanotubes@ graphene oxide nanoribbons heterostructure

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Gangbing, E-mail: zhgb1030@ujs.edu.cn [School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China); Yi, Yinhui; Han, Zhixiang [School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China); Wang, Kun [School of Chemistry and Chemical Engineering, Jiangsu University, Zhenjiang 212013 (China); Wu, Xiangyang, E-mail: wuxy@ujs.edu.cn [School of the Environment and Safety Engineering, Jiangsu University, Zhenjiang 212013 (China)

    2014-10-03

    Highlights: • A core–shell heterostructure MWCNTs@GONRs was produced from unzipping MWCNTs. • A new electrochemical sensor for PAAs was developed based on MWCNTs@GONRs hybrids. • The sensor shows good analytical performance for PAAs detection. - Abstract: Being awfully harmful to the environment and human health, the qualitative and quantitative determinations of polycyclic aromatic amines (PAAs) are of great significance. In this paper, a novel core–shell heterostructure of multiwalled carbon nanotubes (MWCNTs) as the core and graphene oxide nanoribbons (GONRs) as the shell (MWCNTs@GONRs) was produced from longitudinal partially unzipping of MWCNTs side walls using a simple wet chemical strategy and applied for electrochemical determination of three kinds of PAAs (1-aminopyrene (1-AP), 1-aminonaphthalene and 3,3′-diaminobiphenyl). Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis and electrochemical methods were used to characterize the as-prepared MWCNTs@GONRs. Due to the synergistic effects from MWCNTs and GONRs, the oxidation currents of PAAs at the MWCNTs@GONRs modified glassy carbon (GC) electrode are much higher than that at the MWCNTs/GC, graphene/GC and bare GC electrodes. 1-AP was used as the representative analyte to demonstrate the sensing performance of the MWCNTs@GONRs/GC electrode, and the proposed modified electrode has a linear response range of 8.0–500.0 nM with a detection limit of 1.5 nM towards 1-AP.

  9. Engineered Solution-Liquid-Solid Growth of a "Treelike" 1D/1D TiO2Nanotube-CdSe Nanowire Heterostructure: Photoelectrochemical Conversion of Broad Spectrum of Solar Energy.

    Science.gov (United States)

    Mukherjee, Bratindranath; Sarker, Swagotom; Crone, Eric; Pathak, Pawan; Subramanian, Vaidyanathan R

    2016-12-07

    This work presents a hitherto unreported approach to assemble a 1D oxide-1D chalcogenide heterostructured photoactive film. As a representative system, bismuth (Bi) catalyzed 1D CdSe nanowires are directly grown on anodized 1D TiO 2 nanotube (T_NT). A combination of the reductive successive-ionic-layer-adsorption-reaction (R-SILAR) and the solution-liquid-solid (S-L-S) approach is implemented to fabricate this heterostructured assembly, reported in this 1D/1D form for the first time. XRD, SEM, HRTEM, and elemental mapping are performed to systematically characterize the deposition of bismuth on T_NT and the growth of CdSe nanowires leading to the evolution of the 1D/1D heterostructure. The resulting "treelike" photoactive architecture demonstrates UV-visible light-driven electron-hole pair generation. The photoelectrochemical results highlight: (i) the formation of a stable n-n heterojunction between TiO 2 nanotube and CdSe nanowire, (ii) an excellent correlation between the absorbance vis-à-vis light conversion efficiency (IPCE), and (iii) a photocurrent density of 3.84 mA/cm 2 . This proof-of-concept features the viability of the approach for designing such complex 1D/1D oxide-chalcogenide heterostructures that can be of interest to photovoltaics, photocatalysis, environmental remediation, and sensing.

  10. Enhanced Giant Piezoresistance Performance of Sandwiched ZnS/Si/SiO2 Radial Heterostructure Nanotubes for Nonvolatile Stress Memory with Repeatable Writing and Erasing.

    Science.gov (United States)

    Cheng, Baochang; Xiong, Li; Cai, Qiangsheng; Shi, Haiping; Zhao, Jie; Su, Xiaohui; Xiao, Yanhe; Lei, Shuijin

    2016-12-21

    It is a challenge to realize nonvolatile stress-writing memory. Herein, we propose a strategy to construct rewritable stress information storage devices, consisting of deliberately designing individual sandwiched ZnS/Si/SiO2 radial heterostructure nanotubes synthesized by one-step thermal evaporation method. A bulk trap-related Poole-Frenkel hopping mechanism is proposed. Carriers are localized in a narrow bandgap Si intermediate layer; moreover, incorporated impurities and heterointerface defects can serve as charge trap centers or storage mediators. Compressive strain can induce trap barrier height to decrease at relatively low operation bias voltage, whereas tensile strain can induce it to increase, resulting in a giant piezoresistance effect. After both loading compressive and tensile strains at low bias voltage, additionally, the emptying of trap states results in a high resistance state. However, the emptied trap states can be filled by applying a relatively high bias voltage without strains and, correspondingly, the memories return to low resistance state. The emptying and filling of trap states, respectively applied by strains and high electric field, result in a repeatable writing/erasing nonvolatile memory effect. The results indicate that the creation and modification of trap states in multiscale nanostructures can give an avenue to the development of novel nanodevices for rewritable nonvolatile stress sensor and memory.

  11. Sensitive electrochemical sensing for polycyclic aromatic amines based on a novel core-shell multiwalled carbon nanotubes@ graphene oxide nanoribbons heterostructure.

    Science.gov (United States)

    Zhu, Gangbing; Yi, Yinhui; Han, Zhixiang; Wang, Kun; Wu, Xiangyang

    2014-10-03

    Being awfully harmful to the environment and human health, the qualitative and quantitative determinations of polycyclic aromatic amines (PAAs) are of great significance. In this paper, a novel core-shell heterostructure of multiwalled carbon nanotubes (MWCNTs) as the core and graphene oxide nanoribbons (GONRs) as the shell (MWCNTs@GONRs) was produced from longitudinal partially unzipping of MWCNTs side walls using a simple wet chemical strategy and applied for electrochemical determination of three kinds of PAAs (1-aminopyrene (1-AP), 1-aminonaphthalene and 3,3'-diaminobiphenyl). Scanning electron microscopy, transmission electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis and electrochemical methods were used to characterize the as-prepared MWCNTs@GONRs. Due to the synergistic effects from MWCNTs and GONRs, the oxidation currents of PAAs at the MWCNTs@GONRs modified glassy carbon (GC) electrode are much higher than that at the MWCNTs/GC, graphene/GC and bare GC electrodes. 1-AP was used as the representative analyte to demonstrate the sensing performance of the MWCNTs@GONRs/GC electrode, and the proposed modified electrode has a linear response range of 8.0-500.0 nM with a detection limit of 1.5 nM towards 1-AP. Copyright © 2014 Elsevier B.V. All rights reserved.

  12. Synthesis of Ag-loaded SrTiO{sub 3}/TiO{sub 2} heterostructure nanotube arrays for enhanced photocatalytic performances

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Zijun; Chen, Da; Zhan, Xiaqiang; Wang, Fang; Qin, Laishun; Huang, Yuexiang [China Jiliang University, College of Materials Science and Engineering, Hangzhou, Zhejiang (China)

    2017-06-15

    In this work, the effect of loading Ag nanoparticles on the photocatalytic activity of SrTiO{sub 3}/TiO{sub 2} nanotube arrays (TNTAs) was investigated. TNTAs were partially transformed to SrTiO{sub 3} through a hydrothermal treatment, which could preserve the tubular structure of TNTAs, and then, Ag nanoparticles were well deposited on the surface of SrTiO{sub 3}/TNTAs heterostructure by a chemical reduction process. Compared to the TNTAs sample, the Ag-loaded SrTiO{sub 3}/TNTAs sample showed significantly enhanced photocatalytic activities for photodegradation of rhodamine B. The enhanced photocatalytic activity of Ag-loaded SrTiO{sub 3}/TNTAs could be attributed to the increased optical absorption as well as the efficient charge transfer and separation of photogenerated electron-hole pairs induced by the SrTiO{sub 3}/TNTAs heterojunction and the Schottky barrier between metallic Ag and SrTiO{sub 3}/TNTAs. On the basis of the trapping experiments, the possible photocatalytic mechanism was also discussed. (orig.)

  13. Enabling Flexible Heterostructures for Li-Ion Battery Anodes Based on Nanotube and Liquid-Phase Exfoliated 2D Gallium Chalcogenide Nanosheet Colloidal Solutions.

    Science.gov (United States)

    Zhang, Chuanfang John; Park, Sang-Hoon; Ronan, Oskar; Harvey, Andrew; Seral-Ascaso, Andrés; Lin, Zifeng; McEvoy, Niall; Boland, Conor S; Berner, Nina C; Duesberg, Georg S; Rozier, Patrick; Coleman, Jonathan N; Nicolosi, Valeria

    2017-09-01

    2D metal chalcogenide (MC) nanosheets (NS) have displayed high capacities as lithium-ion battery (LiB) anodes. Nevertheless, their complicated synthesis routes coupled with low electronic conductivity greatly limit them as promising LiB electrode material. Here, this work reports a facile single-walled carbon nanotube (SWCNT) percolating strategy for efficiently maximizing the electrochemical performances of gallium chalcogenide (GaX, X = S or Se). Multiscaled flexible GaX NS/SWCNT heterostructures with abundant voids for Li(+) diffusion are fabricated by embedding the liquid-exfoliated GaX NS matrix within a SWCNT-percolated network; the latter improves the electron transport and ion diffusion kinetics as well as maintains the mechanical flexibility. Consequently, high capacities (i.e., 838 mAh g(-1) per gallium (II) sulfide (GaS) NS/SWCNT mass and 1107 mAh g(-1) per GaS mass; the latter is close to the theoretical value) and good rate capabilities are achieved, which can be majorly attributed to the alloying processes of disordered Ga formed after the first irreversible GaX conversion reaction, as monitored by in situ X-ray diffraction. The presented approach, colloidal solution processing of SWCNT and liquid-exfoliated MC NS to produce flexible paper-based electrode, could be generalized for wearable energy storage devices with promising performances. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Nanoscale nickel oxide/nickel heterostructures for active hydrogen evolution electrocatalysis

    National Research Council Canada - National Science Library

    Gong, Ming; Zhou, Wu; Tsai, Mon-Che; Zhou, Jigang; Guan, Mingyun; Lin, Meng-Chang; Zhang, Bo; Hu, Yongfeng; Wang, Di-Yan; Yang, Jiang; Pennycook, Stephen J; Hwang, Bing-Joe; Dai, Hongjie

    2014-01-01

    .... Here we report nanoscale nickel oxide/nickel heterostructures formed on carbon nanotube sidewalls as highly effective electrocatalysts for hydrogen evolution reaction with activity similar to platinum...

  15. NiCo2S4@NiMoO4 Core-Shell Heterostructure Nanotube Arrays Grown on Ni Foam as a Binder-Free Electrode Displayed High Electrochemical Performance with High Capacity

    Science.gov (United States)

    Zhang, Yan; Xu, Jie; Zheng, Yayun; Zhang, Yingjiu; Hu, Xing; Xu, Tingting

    2017-06-01

    Core-shell-structured system has been proved as one of the best architecture for clean energy products owing to its inherited superiorities from both the core and the shell part, which can provide better conductivity and high surface area. Herein, a hierarchical core-shell NiCo2S4@NiMoO4 heterostructure nanotube array on Ni foam (NF) (NiCo2S4@NiMoO4/NF) has been successfully fabricated. Because of its novel heterostructure, the capacitive performance has been enhanced. A specific capacitance up to 2006 F g-1 was obtained at a current density of 5 mA cm-2, which was far higher than that of pristine NiCo2S4 nanotube arrays (about 1264 F g-1). More importantly, NiCo2S4@NiMoO4/NF and active carbon (AC) were congregated as positive electrode and negative electrode in an asymmetric supercapacitor. As-fabricated NiCo2S4@NiMoO4/NF//AC device has a good cyclic behavior with 78% capacitance retention over 2000 cycles, and exhibits a high energy density of 21.4 Wh kg-1 and power density of 58 W kg-1 at 2 mA cm-2. As displayed, the NiCo2S4@NiMoO4/NF core-shell herterostructure holds great promise for supercapacitors in energy storage.

  16. Coaxial foilless diode

    OpenAIRE

    Long Kong; QingXiang Liu; XiangQiang Li; ShaoMeng Wang

    2014-01-01

    A kind of coaxial foilless diode is proposed in this paper, with the structure model and operating principle of the diode are given. The current-voltage relation of the coaxial foilless diode and the effects of structure parameters on the relation are studied by simulation. By solving the electron motion equation, the beam deviation characteristic in the presence of external magnetic field in transmission process is analyzed, and the relationship between transverse misalignment with diode par...

  17. Coaxial foilless diode

    Directory of Open Access Journals (Sweden)

    Long Kong

    2014-05-01

    Full Text Available A kind of coaxial foilless diode is proposed in this paper, with the structure model and operating principle of the diode are given. The current-voltage relation of the coaxial foilless diode and the effects of structure parameters on the relation are studied by simulation. By solving the electron motion equation, the beam deviation characteristic in the presence of external magnetic field in transmission process is analyzed, and the relationship between transverse misalignment with diode parameters is obtained. These results should be of interest to the area of generation and propagation of radial beam for application of generating high power microwaves.

  18. Coaxial Electric Heaters

    Science.gov (United States)

    Strekalov, Dmitry; Matsko, Andrey; Savchenkov, Anatoliy; Maleki, Lute

    2008-01-01

    Coaxial electric heaters have been conceived for use in highly sensitive instruments in which there are requirements for compact heaters but stray magnetic fields associated with heater electric currents would adversely affect operation. Such instruments include atomic clocks and magnetometers that utilize heated atomic-sample cells, wherein stray magnetic fields at picotesla levels could introduce systematic errors into instrument readings. A coaxial electric heater is essentially an axisymmetric coaxial cable, the outer conductor of which is deliberately made highly electrically resistive so that it can serve as a heating element. As in the cases of other axisymmetric coaxial cables, the equal magnitude electric currents flowing in opposite directions along the inner and outer conductors give rise to zero net magnetic field outside the outer conductor. Hence, a coaxial electric heater can be placed near an atomic-sample cell or other sensitive device. A coaxial electric heater can be fabricated from an insulated copper wire, the copper core of which serves as the inner conductor. For example, in one approach, the insulated wire is dipped in a colloidal graphite emulsion, then the emulsion-coated wire is dried to form a thin, uniform, highly electrically resistive film that serves as the outer conductor. Then the film is coated with a protective layer of high-temperature epoxy except at the end to be electrically connected to the power supply. Next, the insulation is stripped from the wire at that end. Finally, electrical leads from the heater power supply are attached to the exposed portions of the wire and the resistive film. The resistance of the graphite film can be tailored via its thickness. Alternatively, the film can be made from an electrically conductive paint, other than a colloidal graphite emulsion, chosen to impart the desired resistance. Yet another alternative is to tailor the resistance of a graphite film by exploiting the fact that its resistance

  19. Emission color-tuned light-emitting diode microarrays of nonpolar InxGa1-xN/GaN multishell nanotube heterostructures

    Science.gov (United States)

    Hong, Young Joon; Lee, Chul-Ho; Yoo, Jinkyoung; Kim, Yong-Jin; Jeong, Junseok; Kim, Miyoung; Yi, Gyu-Chul

    2015-12-01

    Integration of nanostructure lighting source arrays with well-defined emission wavelengths is of great importance for optoelectronic integrated monolithic circuitry. We report on the fabrication and optical properties of GaN-based p-n junction multishell nanotube microarrays with composition-modulated nonpolar m-plane InxGa1-xN/GaN multiple quantum wells (MQWs) integrated on c-sapphire or Si substrates. The emission wavelengths were controlled in the visible spectral range of green to violet by varying the indium mole fraction of the InxGa1-xN MQWs in the range 0.13 ≤ x ≤ 0.36. Homogeneous emission from the entire area of the nanotube LED arrays was achieved via the formation of MQWs with uniform QW widths and composition by heteroepitaxy on the well-ordered nanotube arrays. Importantly, the wavelength-invariant electroluminescence emission was observed above a turn-on of 3.0 V because both the quantum-confinement Stark effect and band filling were suppressed due to the lack of spontaneous inherent electric field in the m-plane nanotube nonpolar MQWs. The method of fabricating the multishell nanotube LED microarrays with controlled emission colors has potential applications in monolithic nonpolar photonic and optoelectronic devices on commonly used c-sapphire and Si substrates.

  20. Novel electric double-layer capacitor with a coaxial fiber structure.

    Science.gov (United States)

    Chen, Xuli; Qiu, Longbin; Ren, Jing; Guan, Guozhen; Lin, Huijuan; Zhang, Zhitao; Chen, Peining; Wang, Yonggang; Peng, Huisheng

    2013-11-26

    A coaxial electric double-layer capacitor fiber is developed from the aligned carbon nanotube fiber and sheet, which functions as two electrodes with a polymer gel sandwiched between them. The unique coaxial structure enables a rapid transportation of ions between the two electrodes with a high electrochemical performance. These energy storage fibers are also flexible and stretchable, and can be woven into and widely used for electronic textiles. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. High power coaxial ubitron

    Science.gov (United States)

    Balkcum, Adam J.

    In the ubitron, also known as the free electron laser, high power coherent radiation is generated from the interaction of an undulating electron beam with an electromagnetic signal and a static periodic magnetic wiggler field. These devices have experimentally produced high power spanning the microwave to x-ray regimes. Potential applications range from microwave radar to the study of solid state material properties. In this dissertation, the efficient production of high power microwaves (HPM) is investigated for a ubitron employing a coaxial circuit and wiggler. Designs for the particular applications of an advanced high gradient linear accelerator driver and a directed energy source are presented. The coaxial ubitron is inherently suited for the production of HPM. It utilizes an annular electron beam to drive the low loss, RF breakdown resistant TE01 mode of a large coaxial circuit. The device's large cross-sectional area greatly reduces RF wall heat loading and the current density loading at the cathode required to produce the moderate energy (500 keV) but high current (1-10 kA) annular electron beam. Focusing and wiggling of the beam is achieved using coaxial annular periodic permanent magnet (PPM) stacks without a solenoidal guide magnetic field. This wiggler configuration is compact, efficient and can propagate the multi-kiloampere electron beams required for many HPM applications. The coaxial PPM ubitron in a traveling wave amplifier, cavity oscillator and klystron configuration is investigated using linear theory and simulation codes. A condition for the dc electron beam stability in the coaxial wiggler is derived and verified using the 2-1/2 dimensional particle-in-cell code, MAGIC. New linear theories for the cavity start-oscillation current and gain in a klystron are derived. A self-consistent nonlinear theory for the ubitron-TWT and a new nonlinear theory for the ubitron oscillator are presented. These form the basis for simulation codes which, along

  2. CO-AXIAL DISCHARGES

    Science.gov (United States)

    Luce, J.S.; Smith, L.P.

    1960-11-22

    A method and apparatus are given for producing coaxial arc discharges in an evacuated enclosure and within a strong, confining magnetic field. The arcs are maintained at a high potential difference. Electrons will diffuse to the more positive arc from the negative arc, and positive ions will diffuse from the more positive arc to the negative arc. Coaxial arc discharges have the advantage that ions which return to strike the positive arc discharge will lose no energy since they do not strike a solid wall or electrode. Those discharges are useful in confining an ionized plasma between the discharges, and have the advantage of preventing impurities from the walls of the enclosure from entering ihe plasma area because of the arc barrier set up bv the cylindrical outer arc.

  3. Electrochemical synthesis of coaxial TiO2–Ag nanowires and their application in photocatalytic water splitting

    NARCIS (Netherlands)

    Maijenburg, A.W.; Veerbeek, Janneke; de Putter, R.; Veldhuis, Sjoerd; Zoontjes, M.G.C.; Mul, Guido; Montero-Moreno, J.M.; Nielsch, K.; Schäfer, H.; Steinhart, M.; ten Elshof, Johan E.

    2014-01-01

    A new method for the formation of coaxial TiO2–Ag nanowires is presented, in which TiO2 nanotubes were formed by the templated electrochemically induced sol–gel method, followed by thermal annealing. The as-formed TiO2 nanotubes have been successfully filled with a Ag core using a subsequent

  4. Coaxial slow source

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, R.D.; Jarboe, T.R.

    1990-01-01

    Field reversed configurations (FRCs) are a class of compact toroid with not toroidal field. The field reversed theta pinch technique has been successfully used for formation of FRCs since their inception in 1958. In this method an initial bias field is produced. After ionization of the fill gas, the current in the coil is rapidly reversed producing the radial implosion of a current sheath. At the ends of the coil the reversed field lines rapidly tear and reconnect with the bias field lines until no more bias flux remains. At this point, vacuum reversed field accumulates around the configuration which contracts axially until an equilibrium is reached. When extrapolating the use of such a technique to reactor size plasmas two main shortcomings are found. First, the initial bias field, and hence flux in a given device, which can be reconnected to form the configuration is limited from above by destructive axial dynamics. Second, the voltages required to produce rapid current reversal in the coil are very large. Clearly, a low voltage formation technique without limitations on flux addition is desirable. The Coaxial Slow Source (CSS) device was designed to meet this need. It has two coaxial theta pinch coils. Coaxial coil geometry allows for the addition of as much magnetic flux to the annular plasma between them as can be generated inside the inner coil. Furthermore the device can be operated at charging voltages less than 10 kV and on resistive diffusion, rather than implosive time scales. The inner coil is a novel, concentric, helical design so as to allow it to be cantilevered on one end to permit translation of the plasma. Following translation off the inner coil the Annular Field Reversed Configuration would be re-formed as a true FRC. In this paper we investigate the formation process in the new parallel configuration., CSSP, in which the inner and outer coils are connected in parallel to the main capacitor bank.

  5. Coaxial slow source

    Science.gov (United States)

    Brooks, R. D.; Jarboe, T. R.

    Field reversed configurations (FRC's) are a class of compact toroid with no toroidal field. The field reversed theta pinch technique has been successfully used for formation of FRC's since their inception in 1958. In this method an initial bias field is produced. After ionization of the fill gas, the current in the coil is rapidly reversed producing the radial implosion of a current sheath. At the ends of the coil the reversed field lines rapidly tear and reconnect with the bias field lines until no more bias flux remains. At this point, vacuum reversed field accumulates around the configuration which contracts axially until an equilibrium is reached. When extrapolating the use of such a technique to reactor size plasmas two main shortcomings are found. First, the initial bias field, and hence flux in a given device, which can be reconnected to form the configuration is limited from above by destructive axial dynamics. Second, the voltages required to produce rapid current reversal in the coil are very large. Clearly, a low voltage formation technique without limitations on flux addition is desirable. The Coaxial Slow Source (CSS) device was designed to meet this need. It has two coaxial theta pinch coils. Coaxial coil geometry allows for the addition of as much magnetic flux to the annular plasma between them as can be generated inside the inner coil. Furthermore the device can be operated at charging voltages less than 10 kV and on resistive diffusion, rather than implosive time scales. The inner coil is a novel, concentric, helical design so as to allow it to be cantilevered on one end to permit translation of the plasma. Following translation off the inner coil the Annular Field Reversed Configuration would be re-formed as a true FRC. In this paper, we investigate the formation process in the new parallel configuration, CSSP, in which the inner and outer coils are connected in parallel to the main capacitor bank.

  6. From GaN to ZnGa(2)O(4) through a low-temperature process: nanotube and heterostructure arrays.

    Science.gov (United States)

    Lu, Ming-Yen; Zhou, Xiang; Chiu, Cheng-Yao; Crawford, Samuel; Gradečak, Silvija

    2014-01-22

    We demonstrate a method to synthesize GaN-ZnGa2O4 core-shell nanowire and ZnGa2O4 nanotube arrays by a low-temperature hydrothermal process using GaN nanowires as templates. Transmission electron microscopy and X-ray photoelectron spectroscopy results show that a ZnGa2O4 shell forms on the surface of GaN nanowires and that the shell thickness is controlled by the time of the hydrothermal process and thus the concentration of Zn ions in the solution. Furthermore, ZnGa2O4 nanotube arrays were obtained by depleting the GaN core from GaN-ZnGa2O4 core-shell nanowire arrays during the reaction and subsequent etching with HCl. The GaN-ZnGa2O4 core-shell nanowires exhibit photoluminescence peaks centered at 2.60 and 2.90 eV attributed to the ZnGa2O4 shell, as well as peaks centered at 3.35 and 3.50 eV corresponding to the GaN core. We also demonstrate the synthesis of GaN-ZnGa2O4 heterojunction nanowires by a selective formation process as a simple route toward development of heterojunction nanodevices for optoelectronic applications.

  7. Atomic Layer Deposition of ZnO on Multi-walled Carbon Nanotubes and Its Use for Synthesis of CNT–ZnO Heterostructures

    Directory of Open Access Journals (Sweden)

    Li C

    2010-01-01

    Full Text Available Abstract In this article, direct coating of ZnO on PECVD-grown multi-walled carbon nanotubes (MWCNTs is achieved using atomic layer deposition (ALD. Transmission electron microscopy investigation shows that the deposited ZnO shell is continuous and uniform, in contrast to the previously reported particle morphology. The ZnO layer has a good crystalline quality as indicated by Raman and photoluminescence (PL measurements. We also show that such ZnO layer can be used as seed layer for subsequent hydrothermal growth of ZnO nanorods, resulting in branched CNT–inorganic hybrid nanostructures. Potentially, this method can also apply to the fabrication of ZnO-based hybrid nanostructures on other carbon nanomaterials.

  8. High efficient photocatalytic activity from nanostructuralized photonic crystal-like p-n coaxial hetero-junction film photocatalyst of Cu3SnS4/TiO2 nanotube arrays

    Science.gov (United States)

    Li, Yan; Liu, Fang-Ting; Chang, Yin; Wang, Jian; Wang, Cheng-Wei

    2017-12-01

    Structuring the materials in the form of photonic crystals is a new strategy for photocatalytic applications. Herein, a new concept of photonic crystal-induced p-n coaxial heterojunction film photocatalyst of Cu3SnS4/TiO2 (CTS/PhC-TNAs) was well-designed and successfully fabricated by combining periodic pulse anodic oxidation and in-situ self-assembling methods Such nanostructured CTS/PhC-TNAs exhibited significantly improved photocatalytic degradation activity under simulated sunlight irradiation with methyl orange (MO) as the target pollutants. Within 120 min, 82% of the MO (10 mg/L) was photodegraded and its kinetic constant per specific surface area reached 0.05332 μmol/m2h, which is 1.6 and 12.8 times more quickly than that of PhC-TNAs and CTS, respectively. Its significantly enhanced photocatalytic activity could be mainly attributed to a joint effect of the unique photonic crystal property of PhC-TNAs and the nanostructured hollow p-n coaxial hetero-junction, which result in an increased efficiency of charge separation and transfer and also an improved spectral response capability. This photonic crystal film photocatalyst has the potential for enhancing the photocatalytic activity via further optimizing the photonic stop band of PhC-TNAs. The study presents a new means to design the kind of photonic crystal structural-induced novel photocatalysts with high photocatalytic activities in pollution treatment.

  9. Growth of three dimensional flower-like molybdenum disulfide hierarchical structures on graphene/carbon nanotube network: An advanced heterostructure for energy storage devices

    Science.gov (United States)

    Lingappan, Niranjanmurthi; Van, Ngoc Huynh; Lee, Suok; Kang, Dae Joon

    2015-04-01

    We report the design and synthesis of three dimensional flower-like molybdenum disulphide (f-MoS2) hierarchical structures, on reduced graphene oxide (RGO)/oxidized multi-walled carbon nanotube (o-MWCNT) backbone (f-MoS2/RGO/o-MWCNT), through one-pot hydrothermal method. Control experiments reveal that the homogenously distributed o-MWCNTs on RGO play an essential role for the formation of such morphology. As an anode for lithium ion batteries, the f-MoS2/RGO/o-MWCNT hybrid delivers a high reversible capacity of 1275 mAh g-1 at the current density of 100 mA g-1, superior rate capability and excellent long cycle life, with capacity retention of 93% after 100 cycles. The outstanding electrochemical performance can be attributed to the large surface area, short diffusion length and continuous electron transport pathway, as a consequence of the intimate contact between f-MoS2, graphene, and o-MWCNTs.

  10. Comparison of photoluminescence of carbon nanotube/ZnO nanostructures synthesized by gas- and solution-phase transport

    Science.gov (United States)

    Jin, Changhyun; Lee, Seawook; Kim, Chang-Wan; Park, Suyoung; Lee, Chongmu; Lee, Dongjin

    2015-02-01

    Multiwalled carbon nanotubes (MWCNTs)/ZnO heterostructures were synthesized by two different processes: (1) gas-phase transport (GPT) and nucleation of Zn powders and (2) solution-phase transport (SPT) chemical reaction of zinc nitrate solution on the MWCNTs. Transmission electron microscopy and X-ray diffraction analysis indicated that the ZnO nanostructures on the MWCNTs from the GPT and SPT processes were poly- and single-crystal hexagonal wurtzite structure, respectively. The major photoluminescence (PL) spectra of our MWCNT/ZnO hybrid, excited at 380 nm and 550 nm, were presented. The PL intensity of the MWCNT/ZnO coaxial nanostructures behaves differently depending on the ZnO synthesis methods on the MWCNTs. The MWCNT/ZnO heterostructures synthesized using the GPT process were more efficient than those synthesized by SPT process in enhancing the PL intensity around the near-band-edge emission region. However, the emission enhancement around defect region was mostly attributed to increase in the O vacancy concentration in the ZnO on the MWCNTs during the SPT process.

  11. Permittivity measurements using coaxial probes

    OpenAIRE

    Oliver Riera, Bartomeu

    2017-01-01

    The main objective of this thesis is to characterize, using the ADS software, the coaxial probe provided by the faculty ETSETB and utilize such probe in order to calculate the permittivity of different materials El objetivo principal de esta tesis el de caracterizar, con el programa ADS, la sonda coaxial proporcionada por la facultad de la ETSETB y utilizar-la para el calculo de la permitividad de diferentes materiales. L'objectiu d'aquesta tesis es el de caracteritzar, amb el programa ...

  12. InAs/Si Hetero-Junction Nanotube Tunnel Transistors

    OpenAIRE

    Hanna, Amir N.; Fahad, Hossain M.; Hussain, Muhammad M.

    2015-01-01

    Hetero-structure tunnel junctions in non-planar gate-all-around nanowire (GAA NW) tunnel FETs (TFETs) have shown significant enhancement in ?ON? state tunnel current over their all-silicon counterpart. Here we show the unique concept of nanotube TFET in a hetero-structure configuration that is capable of much higher drive current as opposed to that of GAA NW TFETs.Through the use of inner/outer core-shell gates, a single III-V hetero-structured nanotube TFET leverages physically larger tunnel...

  13. Selective formation of GaN-based nanorod heterostructures on soda-lime glass substrates by a local heating method

    Energy Technology Data Exchange (ETDEWEB)

    Hong, Young Joon; Kim, Yong-Jin [Department of Materials Science and Engineering, POSTECH, Pohang, Gyeongbuk 790-784 (Korea, Republic of); Jeon, Jong-Myeong; Kim, Miyoung; Choi, Jun Hee [Department of Materials Science and Engineering, Seoul National University, Seoul 151-744 (Korea, Republic of); Baik, Chan Wook; Kim, Sun Il; Park, Sung Soo; Kim, Jong Min [Frontier Research Laboratory, Samsung Advanced Institute of Technology, PO Box 111, Kiheung 446-712 (Korea, Republic of); Yi, Gyu-Chul, E-mail: joonie.choi@samsung.com, E-mail: gcyi@snu.ac.kr [National Creative Research Initiative Center for Semiconductor Nanorods, Department of Physics and Astronomy, Seoul National University, Seoul 151-747 (Korea, Republic of)

    2011-05-20

    We report on the fabrication of high-quality GaN on soda-lime glass substrates, heretofore precluded by both the intolerance of soda-lime glass to the high temperatures required for III-nitride growth and the lack of an epitaxial relationship with amorphous glass. The difficulties were circumvented by heteroepitaxial coating of GaN on ZnO nanorods via a local microheating method. Metal-organic chemical vapor deposition of ZnO nanorods and GaN layers using the microheater arrays produced high-quality GaN/ZnO coaxial nanorod heterostructures at only the desired regions on the soda-lime glass substrates. High-resolution transmission electron microscopy examination of the coaxial nanorod heterostructures indicated the formation of an abrupt, semicoherent interface. Photoluminescence and cathodoluminescence spectroscopy was also applied to confirm the high optical quality of the coaxial nanorod heterostructures. Mg-doped GaN/ZnO coaxial nanorod heterostructure arrays, whose GaN shell layers were grown with various different magnesocene flow rates, were further investigated by using photoluminescence spectroscopy for the p-type doping characteristics. The suggested method for fabrication of III-nitrides on glass substrates signifies potentials for low-cost and large-size optoelectronic device applications.

  14. Fabrication of vertical GaN/InGaN heterostructure nanowires using Ni-Au bi-metal catalysts.

    Science.gov (United States)

    Ha, Ryong; Kim, Sung-Wook; Choi, Heon-Jin

    2013-06-26

    We have fabricated the vertically aligned coaxial or longitudinal heterostructure GaN/InGaN nanowires. The GaN nanowires are first vertically grown by vapor-liquid-solid mechanism using Au/Ni bi-metal catalysts. The GaN nanowires are single crystal grown in the [0001] direction, with a length and diameter of 1 to 10 μm and 100 nm, respectively. The vertical GaN/InGaN coaxial heterostructure nanowires (COHN) are then fabricated by the subsequent deposition of 2 nm of InxGa1-xN shell on the surface of GaN nanowires. The vertical GaN/InGaN longitudinal heterostructure nanowires (LOHN) are also fabricated by subsequent growth of an InGaN layer on the vertically aligned GaN nanowires using the catalyst. The photoluminescence from the COHN and LOHN indicates that the optical properties of GaN nanowires can be tuned by the formation of a coaxial or longitudinal InGaN layer. Our study demonstrates that the bi-metal catalysts are useful for growing vertical as well as heterostructure GaN nanowires. These vertically aligned GaN/InGaN heterostructure nanowires may be useful for the development of high-performance optoelectronic devices.

  15. Coaxial hybrid iron (CHI) wiggler

    Science.gov (United States)

    Jackson, Robert H.; Freund, Henry P.; Pershing, Dean E.; Taccetti, J. M.

    1993-11-01

    A magnetic wiggler design has been developed for applications in free-electron lasers which is scalable to small periods with high field amplitude, high beam current acceptance, and excellent transverse focusing and beam propagation properties. The Coaxial Hybrid Iron (CHI) wiggler design consists of a coaxial arrangement of alternating ferromagnetic and non- ferromagnetic rings with the central portion of the coax shifted by one half period. The entire arrangement is immersed in a solenoidal field which results in a cylindrically symmetric periodic field. A key advantage of this wiggler configuration is its capacity to handle very high beam currents with excellent focusing and transport properties. FEL configuration using the CHI wiggler design have the potential for high power, high frequency coherent generation in relatively compact systems. Analytic and simulated characteristics of the CHI wiggler are presented.

  16. Instabilities in coaxial rotating jets

    Science.gov (United States)

    Ivanic, Tanja; Foucault, Eric; Pecheux, Jean; Gilard, Virginie

    2000-12-01

    The aim of this study is the characterization of the cylindrical mixing layer resulting from the interaction of two coaxial swirling jets. The experimental part of this study was performed in a cylindrical water tunnel, permitting an independent rotation of two coaxial jets. The rotations are generated by means of 2×36 blades localized in two swirling chambers. As expected, the evolution of the main instability modes presents certain differences compared to the plane-mixing-layer case. Experimental results obtained by tomography showed the existence of vortex rings and streamwise vortex pairs in the near field region. This method also permitted the observation of the evolution and interaction of different modes. PIV velocity measurements realized in the meridian plans and the plans perpendicular to the jet axis show that rotation distorts the typical top-hat axial velocity profile. The transition of the axial velocity profile from jet-like into wake-like is also observed.

  17. Note: cryogenic coaxial microwave filters.

    Science.gov (United States)

    Tancredi, G; Schmidlin, S; Meeson, P J

    2014-02-01

    The careful filtering of microwave electromagnetic radiation is critical for controlling the electromagnetic environment for experiments in solid-state quantum information processing and quantum metrology at millikelvin temperatures. We describe the design and fabrication of a coaxial filter assembly and demonstrate that its performance is in excellent agreement with theoretical modelling. We further perform an indicative test of the operation of the filters by making current-voltage measurements of small, underdamped Josephson junctions at 15 mK.

  18. Investigation on coaxial stability of nano-bearing under two axis-deviation perturbations

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    A spatial cylindrical model on nano-bearing constructed by double-walled carbon nano-tube (DWCNT) is established. Two motion equations are advanced to characterize the eccentric and deflective mode of the nano-bearing, respectively. On the basis of these equations, the coaxial stability of the nano-bearing under two axis-deviation perturbations is investigated. A characteristic parameter λ * governing the coaxial stability of the nano-bearing is determined. The influences of the angular velocity, interlayer spacing and axial length of the nano-bearing on the characteristic parameter λ * are analyzed and discussed in detail. It is found that when the angular velocity or interlayer spacing is smaller than a certain critical value, the parameter λ * keeps negative, and the coaxial stability of the nano-bearing is maintained. However, the axial length has very insignificant influence on λ * . In addition, for the two non-coaxial modes, the eccentric mode occurs more easily than the deflective one. The results of this paper provide a further insight into the coaxial stability of nano-bearing via the spatial model.

  19. Heterostructures and quantum devices

    CERN Document Server

    Einspruch, Norman G

    1994-01-01

    Heterostructure and quantum-mechanical devices promise significant improvement in the performance of electronic and optoelectronic integrated circuits (ICs). Though these devices are the subject of a vigorous research effort, the current literature is often either highly technical or narrowly focused. This book presents heterostructure and quantum devices to the nonspecialist, especially electrical engineers working with high-performance semiconductor devices. It focuses on a broad base of technical applications using semiconductor physics theory to develop the next generation of electrical en

  20. Realistic simulations of coaxial atomisation

    Science.gov (United States)

    Zaleski, Stephane; Fuster, Daniel; Arrufat Jackson, Tomas; Ling, Yue; Cenni, Matteo; Scardovelli, Ruben; Tryggvason, Gretar

    2015-11-01

    We discuss advances in the methodology for Direct Numerical Simulations of coaxial atomization in typical experimental conditions. Such conditions are extremely demanding for the numerical methods. The key difficulty seems to be the combination of high density ratios, surface tension, and large Reynolds numbers. We explore how using a momentum-conserving Volume-Of-Fluid scheme allows to improve the stability and accuracy of the simulations. We show computational evidence that the use of momentum conserving methods allows to reduce the required number of grid points by an order of magnitude in the simple case of a falling rain drop. We then apply these ideas to coaxial atomization. We show that in moderate-size simulations in air-water conditions close to real experiments, instabilities are still present and then discuss ways to fix them. Among those, removing small VOF debris and improving the time-stepping scheme are two important directions.The accuracy of the simulations is then discussed in comparison with experimental results and in particular the angle of ejection of the structures. The code used for this research is free and distributed at http://parissimulator.sf.net.

  1. InAs/Si Hetero-Junction Nanotube Tunnel Transistors

    KAUST Repository

    Hanna, Amir

    2015-04-29

    Hetero-structure tunnel junctions in non-planar gate-all-around nanowire (GAA NW) tunnel FETs (TFETs) have shown significant enhancement in ‘ON’ state tunnel current over their all-silicon counterpart. Here we show the unique concept of nanotube TFET in a hetero-structure configuration that is capable of much higher drive current as opposed to that of GAA NW TFETs.Through the use of inner/outer core-shell gates, a single III-V hetero-structured nanotube TFET leverages physically larger tunneling area while achieving higher driver current (ION) and saving real estates by eliminating arraying requirement. Numerical simulations has shown that a 10 nm thin nanotube TFET with a 100 nm core gate has a 5×normalized output current compared to a 10 nm diameter GAA NW TFET.

  2. Plasma arc torch with coaxial wire feed

    Science.gov (United States)

    Hooper, Frederick M

    2002-01-01

    A plasma arc welding apparatus having a coaxial wire feed. The apparatus includes a plasma arc welding torch, a wire guide disposed coaxially inside of the plasma arc welding torch, and a hollow non-consumable electrode. The coaxial wire guide feeds non-electrified filler wire through the tip of the hollow non-consumable electrode during plasma arc welding. Non-electrified filler wires as small as 0.010 inches can be used. This invention allows precision control of the positioning and feeding of the filler wire during plasma arc welding. Since the non-electrified filler wire is fed coaxially through the center of the plasma arc torch's electrode and nozzle, the wire is automatically aimed at the optimum point in the weld zone. Therefore, there is no need for additional equipment to position and feed the filler wire from the side before or during welding.

  3. Arc Plasma Gun With Coaxial Powder Feed

    Science.gov (United States)

    Zaplatynsky, Isidor

    1988-01-01

    Redesigned plasma gun provides improved metallic and ceramic coatings. Particles injected directly through coaxial bore in cathode into central region of plasma jet. Introduced into hotter and faster region of plasma jet.

  4. Magnetic nanotubes

    Science.gov (United States)

    Matsui, Hiroshi; Matsunaga, Tadashi

    2010-11-16

    A magnetic nanotube includes bacterial magnetic nanocrystals contacted onto a nanotube which absorbs the nanocrystals. The nanocrystals are contacted on at least one surface of the nanotube. A method of fabricating a magnetic nanotube includes synthesizing the bacterial magnetic nanocrystals, which have an outer layer of proteins. A nanotube provided is capable of absorbing the nanocrystals and contacting the nanotube with the nanocrystals. The nanotube is preferably a peptide bolaamphiphile. A nanotube solution and a nanocrystal solution including a buffer and a concentration of nanocrystals are mixed. The concentration of nanocrystals is optimized, resulting in a nanocrystal to nanotube ratio for which bacterial magnetic nanocrystals are immobilized on at least one surface of the nanotubes. The ratio controls whether the nanocrystals bind only to the interior or to the exterior surfaces of the nanotubes. Uses include cell manipulation and separation, biological assay, enzyme recovery, and biosensors.

  5. Coaxial cable distribution plant performance simulation

    Science.gov (United States)

    Carangi, Mark D.; Chen, Walter Y.; Kerpez, Kenneth J.; Valenti, Craig F.

    1995-11-01

    The CATV system delivers analog video signals from a centralized headend through a tree- and-branch fiber/coax network. That architecture is very cost effective for delivering broadcast video channels to a vast area. The introduction of interactive TV, data and telephony services requires an upstream link from customers to the headend. Although equipment for upstream transmission is available, CATV systems are primarily engineered for the delivery of one way analog broadcast TV programs. In this paper, issues related to two-way digital transmission through the coaxial cable distribution plant are examined. The objective is to establish a reliable computer modeling environment for the study and simulation of general and advanced transmission systems over the coaxial cable distribution plant. The discussions are focused on three general topics: the coaxial cable distribution plant transmission channel, the corresponding noise environment, and applicable transmission system architectures. Two- port network models are developed for the components (coaxial cable, taps, etc.) of the coaxial cable distribution plant. A realistic distribution plant channel model can be constructed based on these component models. The distribution plant noise level is analyzed based on thermal noise level, amplifier noise figure, and the funneling effect. The upstream ingress noise model is also developed. Three advanced transmission systems, adaptive transmitter, frame based equalization, and discrete multitone (DMT), are presented. End to end computer simulation results are presented using QPSK upstream.

  6. SWCNT-MoS2 -SWCNT Vertical Point Heterostructures.

    Science.gov (United States)

    Zhang, Jin; Wei, Yang; Yao, Fengrui; Li, Dongqi; Ma, He; Lei, Peng; Fang, Hehai; Xiao, Xiaoyang; Lu, Zhixing; Yang, Juehan; Li, Jingbo; Jiao, Liying; Hu, Weida; Liu, Kaihui; Liu, Kai; Liu, Peng; Li, Qunqing; Lu, Wei; Fan, Shoushan; Jiang, Kaili

    2017-02-01

    A vertical point heterostructure (VPH) is constructed by sandwiching a two-dimensional (2D) MoS2 flake with two cross-stacked metallic single-walled carbon nanotubes. It can be used as a field-effect transistor with high on/off ratio and a light detector with high spatial resolution. Moreover, the hybrid 1D-2D-1D VPHs open up new possibilities for nanoelectronics and nano-optoelectronics. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Studies on coaxial circular array for underwater transducer applications

    Digital Repository Service at National Institute of Oceanography (India)

    Chakraborty, B.

    This thesis presents analytical methods to study important aspects of a coaxial circular array for wideband underwater transducer application. It begins with detailed theoretical study of a coaxial circular array of three turns and an analysis...

  8. Coaxial plasma thrusters for high specific impulse propulsion

    Science.gov (United States)

    Schoenberg, Kurt F.; Gerwin, Richard A.; Barnes, Cris W.; Henins, Ivars; Mayo, Robert; Moses, Ronald, Jr.; Scarberry, Richard; Wurden, Glen

    1991-01-01

    A fundamental basis for coaxial plasma thruster performance is presented and the steady-state, ideal MHD properties of a coaxial thruster using an annular magnetic nozzle are discussed. Formulas for power usage, thrust, mass flow rate, and specific impulse are acquired and employed to assess thruster performance. The performance estimates are compared with the observed properties of an unoptimized coaxial plasma gun. These comparisons support the hypothesis that ideal MHD has an important role in coaxial plasma thruster dynamics.

  9. A Study of Coaxial Rotor Performance and Flow Field Characteristics

    Science.gov (United States)

    2016-01-22

    Inc. Ames, Iowa, USA ABSTRACT As a precursor to studying the acoustics of a coaxial rotor system, the aerodynamics and flow field of a coaxial rotor... aerodynamics model, was used to predict coaxial rotor performance in hover and forward flight. RotUNS steady hover calculations showed improved performance...small unmanned aerial vehicles ( UAVs ) market. As with all rotorcraft, the rotor noise generated by a coaxial rotor system must be mitigated to minimize

  10. Modified Coaxial Probe Feeds for Layered Antennas

    Science.gov (United States)

    Fink, Patrick W.; Chu, Andrew W.; Dobbins, Justin A.; Lin, Greg Y.

    2006-01-01

    In a modified configuration of a coaxial probe feed for a layered printed-circuit antenna (e.g., a microstrip antenna), the outer conductor of the coaxial cable extends through the thickness of at least one dielectric layer and is connected to both the ground-plane conductor and a radiator-plane conductor. This modified configuration simplifies the incorporation of such radio-frequency integrated circuits as power dividers, filters, and low-noise amplifiers. It also simplifies the design and fabrication of stacked antennas with aperture feeds.

  11. Coaxial nanowire resonant tunneling diodes from non-polar AlN/GaN on silicon

    Science.gov (United States)

    Carnevale, S. D.; Marginean, C.; Phillips, P. J.; Kent, T. F.; Sarwar, A. T. M. G.; Mills, M. J.; Myers, R. C.

    2012-04-01

    Resonant tunneling diodes are formed using AlN/GaN core-shell nanowire heterostructures grown by plasma assisted molecular beam epitaxy on n-Si(111) substrates. By using a coaxial geometry, these devices take advantage of non-polar (m-plane) nanowire sidewalls. Device modeling predicts non-polar orientation should enhance resonant tunneling compared to a polar structure, and that AlN double barriers will lead to higher peak-to-valley current ratios compared to AlGaN barriers. Electrical measurements of ensembles of nanowires show negative differential resistance appearing only at cryogenic temperature. Individual nanowire measurements show negative differential resistance at room temperature with peak current density of 5 × 105 A/cm2.

  12. Triple mode filters with coaxial excitation

    NARCIS (Netherlands)

    Gerini, G.; Bustamante, F.D.; Guglielmi, M.

    2004-01-01

    In this paper we describe triple mode filters in a square waveguide with integrated coaxial input/output excitation. An important feature of the structure proposed is that it is easily amenable to an accurate full wave analysis. In addition to theory, a practical six pole filter with two

  13. Wideband electromagnetically coupled coaxial probe fed slot ...

    African Journals Online (AJOL)

    user

    The antenna structure is shown in figure 1. The upper parasitic layer is horizontal slot loaded rectangular patch and lower one is coaxial probe fed U-slot loaded patch. Due to presence of parasitic element in the stacked configuration, there are two resonant associated with two resonators. These two resonance frequencies ...

  14. Superhydrophobic and oleophobic fibers by coaxial electrospinning.

    Science.gov (United States)

    Han, Daewoo; Steckl, Andrew J

    2009-08-18

    Control of surface wetting properties to produce strongly hydrophobic or hydrophilic effects is at the heart of many macro- and microfluidic applications. In this work, we have investigated coaxial electrospinning to produce core-sheath-structured nano/microfibers that combine different properties from individual core and sheath materials. Teflon AF is an amorphous fluoropolymer that is widely utilized as a hydrophobic material. Hydrophobic fluoropolymers are normally not electrospinnable because their low dielectric constant prevents sufficient charging for a solution to be electrospun. The first Teflon electrospun fibers are reported using coaxial electrospinning with Teflon AF sheath and poly(epsilon-caprolactone) (PCL) core materials. Using these core/sheath fibers, superhydrophobic and oleophobic membranes have been successfully produced. These coaxial fibers also preserve the core material properties as demonstrated with mechanical tensile tests. The fact that a normally nonelectrospinnable material such as Teflon AF has been successfully electrospun when combined with an electrospinnable core material indicates the potential of coaxial electrospinning to provide a new degree of freedom in terms of material combinations for many applications.

  15. Co-axial, high energy gamma generator

    Science.gov (United States)

    Reijonen, Jani Petteri [Princeton, NJ; Gicquel, Frederic [Pennington, NJ

    2011-08-16

    A gamma ray generator includes an ion source in a first chamber. A second chamber is configured co-axially around the first chamber at a lower second pressure. Co-axially arranged plasma apertures separate the two chambers and provide for restricted passage of ions and gas from the first to the second chamber. The second chamber is formed by a puller electrode having at least one long channel aperture to draw ions from the first chamber when the puller electrode is subject to an appropriate applied potential. A plurality of electrodes rings in the third chamber in third pressure co-axially surround the puller electrode and have at least one channel corresponding to the at least one puller electrode aperture and plasma aperture. The electrode rings increase the energy of the ions to a selected energy in stages in passing between successive pairs of the electrodes by application of an accelerating voltage to the successive pairs of accelerator electrodes. A target disposed co-axially around the plurality of electrodes receives the beam of accelerated ions, producing gamma rays.

  16. Titania nanotube arrays surface-modified with ZnO for enhanced photocatalytic applications

    Energy Technology Data Exchange (ETDEWEB)

    Nageri, Manoj; Kalarivalappil, Vijila; Vijayan, Baiju K.; Kumar, Viswanathan, E-mail: vkumar10@yahoo.co.in

    2016-05-15

    Highlights: • Heterostructures of TNA/ZnO synthesised through potentiostatic anodisation followed by hydrothermal method. • Evaluation of morphological features of the heterostructure with hydrothermal processing time. • Correlation of photocatalytic activity of the hetrostructure with its morphology and surface texture. - Abstract: Well ordered titanium dioxide nanotube arrays (TNA) of average diameter 129 nm and wall thickness of 25 nm were fabricated through potentiostatic anodisation of titanium (Ti) metal substrates. Such TNA were subsequently surface-modified with various amounts of zinc oxide (ZnO) nanopowders using hydrothermal technique to obtain heterogeneous TNA/ZnO nanostructures. The crystalline phase and surface microstructure of the heterostructures were determined by X-ray diffraction, Raman spectroscopy and scanning electron microscopy respectively. The morphology of the heterostructures strongly depended on the hydrothermal conditions employed. The photocatalytic activity of the heterostructures have also been investigated and correlated with their surface morphology and texture.

  17. Mixed Dimensional Van der Waals Heterostructures for Opto-Electronics.

    Science.gov (United States)

    Jariwala, Deep

    The isolation of a growing number of two-dimensional (2D) materials has inspired worldwide efforts to integrate distinct 2D materials into van der Waals (vdW) heterostructures. While a tremendous amount of research activity has occurred in assembling disparate 2D materials into ``all-2D'' van der Waals heterostructures, this concept is not limited to 2D materials alone. Given that any passivated, dangling bond-free surface will interact with another via vdW forces, the vdW heterostructure concept can be extended to include the integration of 2D materials with non-2D materials that adhere primarily through noncovalent interactions. In the first part of this talk I will present our work on emerging mixed-dimensional (2D + nD, where n is 0, 1 or 3) heterostructure devices performed at Northwestern University. I will present two distinct examples of gate-tunable p-n heterojunctions 1. Single layer n-type MoS2\\ (2D) combined with p-type semiconducting single walled carbon nanotubes (1D) and 2. Single layer MoS2 combined with 0D molecular semiconductor, pentacene. I will present the unique electrical properties, underlying charge transport mechanisms and photocurrent responses in both the above systems using a variety of scanning probe microscopy techniques as well as computational analysis. This work shows that van der Waals interactions are robust across different dimensionalities of materials and can allow fabrication of semiconductor devices with unique geometries and properties unforeseen in bulk semiconductors. Finally, I will briefly discuss our recent work from Caltech on near-unity absorption in atomically-thin photovoltaic devices. This work is supported by the Materials Research Center at Northwestern University, funded by the National Science Foundation (NSF DMR-1121262) and the Resnick Sustainability Institute at Caltech.

  18. Nanotube junctions

    Science.gov (United States)

    Crespi, Vincent Henry; Cohen, Marvin Lou; Louie, Steven Gwon Sheng; Zettl, Alexander Karlwalter

    2003-01-01

    The present invention comprises a new nanoscale metal-semiconductor, semiconductor-semiconductor, or metal-metal junction, designed by introducing topological or chemical defects in the atomic structure of the nanotube. Nanotubes comprising adjacent sections having differing electrical properties are described. These nanotubes can be constructed from combinations of carbon, boron, nitrogen and other elements. The nanotube can be designed having different indices on either side of a junction point in a continuous tube so that the electrical properties on either side of the junction vary in a useful fashion. For example, the inventive nanotube may be electrically conducting on one side of a junction and semiconducting on the other side. An example of a semiconductor-metal junction is a Schottky barrier. Alternatively, the nanotube may exhibit different semiconductor properties on either side of the junction. Nanotubes containing heterojunctions, Schottky barriers, and metal-metal junctions are useful for microcircuitry.

  19. Coaxial Compound Helicopter for Confined Urban Operations

    Science.gov (United States)

    2016-01-22

    for the six passengers, but the design mission is flown with only four passengers. Disk Loading and Rotor Diameter Table 17 shows the impact of...weight with rotor diameter for the baseline configuration, and for the aircraft with ITEP engine, two pilots, and six passengers. Lines of constant...Analysis showed that this combination of requirements is best satisfied by a coaxial main- rotor configuration, with lift compounding to off-load

  20. Synthesis of CuO/Co3O4 Coaxial Heterostructures for Efficient and Recycling Photodegradation

    National Research Council Canada - National Science Library

    R. X. Chen; S. L. Zhu; J. Mao; Z. D. Cui; X. J. Yang; Y. Q. Liang; Z. Y. Li

    2015-01-01

      The highly efficient CuO/Co3O4 composite photocatalyst with different morphologies has been synthesized directly on Cu wire mesh by controlling the composition of cobalt-containing solid precursors...

  1. Photoluminescence performance enhancement of ZnO/MgO heterostructured nanowires and their applications in ultraviolet laser diodes.

    Science.gov (United States)

    Shi, Zhi-Feng; Zhang, Yuan-Tao; Cui, Xi-Jun; Zhuang, Shi-Wei; Wu, Bin; Chu, Xian-Wei; Dong, Xin; Zhang, Bao-Lin; Du, Guo-Tong

    2015-06-07

    Vertically aligned ZnO/MgO coaxial nanowire (NW) arrays were prepared on sapphire substrates by metal-organic chemical vapor deposition combined with a sputtering system. We present a comparative investigation of the morphological and optical properties of the produced heterostructures with different MgO layer thicknesses. Photoluminescence measurements showed that the optical performances of ZnO/MgO coaxial NWs were strongly dependent on the MgO layer thickness. The intensity of deep-level emission (DLE) decreased monotonously with the increase of MgO thickness, while the enhancement of ultraviolet (UV) emission showed a critical thickness of 15 nm, achieving a maximum intensity ratio (∼226) of IUV/IDLE at the same time. The significantly improved exciton emission efficiency of the coaxial NW structures allows us to study the surface passivation effect, photogenerated carrier confinement and transfer in terms of energy band theory. More importantly, we achieved an ultralow threshold (4.5 mA, 0.58 A cm(-2)) electrically driven UV lasing action based on the ZnO/MgO NW structures by constructing an Au/MgO/ZnO metal/insulator/semiconductor diode, and the continuous-current-driven diode shows a good temperature tolerance. The results obtained on the unique optical properties of ZnO/MgO coaxial NWs shed light on the design and development of ZnO-based UV laser diodes assembled with nanoscale building blocks.

  2. Heterostructures of transition metal dichalcogenides

    KAUST Repository

    Amin, Bin

    2015-08-24

    The structural, electronic, optical, and photocatalytic properties of out-of-plane and in-plane heterostructures of transition metal dichalcogenides are investigated by (hybrid) first principles calculations. The out-of-plane heterostructures are found to be indirect band gap semiconductors with type-II band alignment. Direct band gaps can be achieved by moderate tensile strain in specific cases. The excitonic peaks show blueshifts as compared to the parent monolayer systems, whereas redshifts occur when the chalcogen atoms are exchanged along the series S-Se-Te. Strong absorption from infrared to visible light as well as excellent photocatalytic properties can be achieved.

  3. Mixing in Shear Coaxial Jets (Briefing Charts)

    Science.gov (United States)

    2013-08-01

    stability theory for inviscid instability of a hyperbolic tangent velocity profile for free boundary layers • U(y)=0.5[1 + tanh(y)] • Chigier and Beer, 1964... Vibration , 48 (2), 1976 1. A. S. H. KWAN and N. W. M. Ko 1976 Journal of Sound and Vibration 48, 203-219. Coherent structures in subsonic coaxial jets...2. Kwan ASH and Ko WM, J. Sound and Vibration , 48 (2), 1976, Coherent structures in subsonic coaxiial jets. 3. N. W. M. KO and A. S. H. KWAN 1976

  4. Graphenylene Nanotubes.

    Science.gov (United States)

    Koch, Andrew T; Khoshaman, Amir H; Fan, Harrison D E; Sawatzky, George A; Nojeh, Alireza

    2015-10-01

    A new type of carbon nanotube, based on the graphenylene motif, is investigated using density functional and tight-binding methods. Analogous to conventional graphene-based nanotubes, a two-dimensional graphenylene sheet can be "rolled" into a seamless cylinder in armchair, zigzag, or chiral orientations. The resulting nanotube can be described using the familiar (n,m) nomenclature and possesses 4-, 6-, and 12-membered rings, with three distinct bond lengths, indicating a nonuniform distribution of the electron density. The dodecagonal rings form pores, 3.3 Å in diameter in graphenylene, which become saddle-shaped paraboloids in smaller-diameter nanotubes. Density functional theory predicts zigzag nanotubes to be small-band gap semiconductors, with a generally decreasing band gap as the diameter increases. Interestingly, the calculations predict metallic characteristics for armchair nanotubes with small diameters (characteristics for larger-diameter ones. Graphenylene nanotubes with indices mod(n-m,3) = 0 exhibit a band gap approximately equal to that of armchair graphenylene nanotubes with comparable diameter.

  5. Investigation on carbon nanomaterials: Coaxial CNT-cylinders and ...

    Indian Academy of Sciences (India)

    Wintec

    Investigation on carbon nanomaterials: Coaxial CNT-cylinders and. CNT-polymer composite. KALPANA AWASTHI, T P YADAV, P R MISHRA, S AWASTHI and. O N SRIVASTAVA*. Department of Physics, Banaras Hindu University, Varanasi 221 005, India. Abstract. The macroscopic coaxial carbon cylinders (dia.

  6. A Review of Double-Walled and Triple-Walled Carbon Nanotube Synthesis and Applications

    Directory of Open Access Journals (Sweden)

    Kazunori Fujisawa

    2016-04-01

    Full Text Available Double- and triple-walled carbon nanotubes (DWNTs and TWNTs consist of coaxially-nested two and three single-walled carbon nanotubes (SWNTs. They act as the geometrical bridge between SWNTs and multi-walled carbon nanotubes (MWNTs, providing an ideal model for studying the coupling interactions between different shells in MWNTs. Within this context, this article comprehensively reviews various synthetic routes of DWNTs’ and TWNTs’ production, such as arc discharge, catalytic chemical vapor deposition and thermal annealing of pea pods (i.e., SWNTs encapsulating fullerenes. Their structural features, as well as promising applications and future perspectives are also discussed.

  7. Escher-like quasiperiodic heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Barriuso, A G; Monzon, J J; Sanchez-Soto, L L [Departamento de Optica, Facultad de Fisica, Universidad Complutense, 28040 Madrid (Spain); Costa, A F [Departamento de Matematicas Fundamentales, Facultad de Ciencias, Universidad Nacional de Educacion a Distancia, Senda del Rey 9, 28040 Madrid (Spain)

    2009-05-15

    Quasiperiodic heterostructures present unique structural, electronic and vibrational properties, connected to the existence of incommensurate periods. We go beyond previous schemes, such as Fibonacci or Thue-Morse, based on substitutional sequences, by introducing construction rules generated by tessellations of the unit disc by regular polygons. We explore some of the properties exhibited by these systems. (fast track communication)

  8. Microminiature coaxial cable and method of manufacture

    Science.gov (United States)

    Bongianni, Wayne L.

    1989-01-01

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 .mu.m thick and from 150 to 200 .mu.m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately, the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microspheres to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

  9. Microminiature coaxial cable and methods of manufacture

    Science.gov (United States)

    Bongianni, W.L.

    1983-12-29

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 ..mu..m thick and from 150 to 200 ..mu..m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dieleectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

  10. Microminiature coaxial cable and methods manufacture

    Science.gov (United States)

    Bongianni, Wayne L.

    1986-01-01

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 .mu.m thick and from 150 to 200 .mu.m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion.

  11. Microminiature coaxial cable and method of manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Bongianni, W.L.

    1989-03-28

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 [mu]m thick and from 150 to 200 [mu]m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately, the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microspheres to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion. 2 figs.

  12. Microminiature coaxial cable and methods manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Bongianni, W.L.

    1986-04-08

    A coaxial cable is provided having a ribbon inner conductor surrounded by a dielectric and a circumferential conductor. The coaxial cable may be microminiature comprising a very thin ribbon strip conductor from between 5 to 15 [mu]m thick and from 150 to 200 [mu]m wide, having a surrounding foamed dielectric or parylene applied thereon by a vapor plasma process and an outer conductor of an adhering high conductivity metal vacuum deposited on the dielectric. Alternately the foam dielectric embodiment may have a contiguous parylene coating applied adjacent the inner conductor or the outer conductor or both. Also, the cable may be fabricated by forming a thin ribbon of strip conductive material into an inner conductor, applying thereabout a dielectric by spraying on a solution of polystyrene and polyethylene and then vacuum depositing and adhering high conductivity metal about the dielectric. The cable strength may be increased by adding glass microfilament fibers or glass microballoons to the solution of polystyrene and polyethylene. Further, the outer conductive layer may be applied by electroless deposition in an aqueous solution rather than by vacuum deposition. A thin coating of parylene is preferably applied to the outer conductor to prevent its oxidation and inhibit mechanical abrasion. 2 figs.

  13. Axisymmetric instabilities between coaxial rotating disks

    Science.gov (United States)

    Pécheux, Jean; Foucault, E.

    2006-09-01

    This paper concerns the stability of the von Kármán swirling flow between coaxial disks. A linear stability analysis shows that for moderate Reynolds numbers (Re≤50) and for any rotation ratio sin[-1,1[ there is a radial location r_{pc} from which the self-similar von Kármán solutions become unstable to axisymmetric disturbances. When the disks are moderately counter-rotating (sin[-0.56,0[), two different disturbances (types I and II) appear at the same critical radius. A spatio-temporal analysis shows that, at a very short distance from this critical radius, the first disturbance (type I) becomes absolutely unstable whereas the second (type II) remains convectively unstable. Outside this range of aspect ratios, all the disturbances examined are found to be absolutely unstable. The flow between two coaxial rotating disks enclosed in a stationary sidewall is then numerically investigated. For sufficently large aspect ratios, the cavity flow is found to be globally unstable for axisymmetric disturbances similar to that calculated with the self-similar solutions. The flow in cavities with aspect ratios smaller than R {≈} 10.3 (and Re {≤} 50) is not destabilized by these axisymmetric disturbances. An experimental investigation conducted for a cavity with aspect ratio R {=} 15 confirms the numerical results. Axisymmetric disturbances similar to those calculated for the same cavity are detected and three-dimensional modes can also be observed near the sidewall.

  14. Needleless coaxial electrospinning: A novel approach to mass production of coaxial nanofibers.

    Czech Academy of Sciences Publication Activity Database

    Vysloužilová, L.; Buzgo, Matej; Pokorný, P.; Chvojka, J.; Míčková, Andrea; Rampichová, Michala; Kula, J.; Pejchar, K.; Bílek, M.; Lukáš, D.; Amler, Evžen

    2017-01-01

    Roč. 516, 1-2 (2017), s. 293-300 ISSN 0378-5173 R&D Projects: GA ČR(CZ) GA15-15697S; GA MŠk(CZ) LO1508; GA MŠk(CZ) LO1309 Institutional support: RVO:68378041 Keywords : core-shell nanofibers * coaxial electrospinning * needleless electrospinning Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.649, year: 2016

  15. Synthesis and characterization of coaxial SnO2-SiO x core-shell nanorods

    Science.gov (United States)

    Liu, Hong Quan; Yuan, Ting; Cui, HongZhi; Chu, ZhiYing; Gu, YiJie

    2016-07-01

    Free-standing coaxial SnO2-SiO x core-shell nanorods were synthesized in a kinetically controlled manner by the chemical vapor transport method. The free-standing SnO2-SiO x core-shell nanorods appear with uniform morphology exhibiting smooth surface, diameters of 100-200 nm, and length of 1 μm. The low oxygen partial pressure and high reaction temperature are advantageous to form the (101) surface, which decreases the (101) crystal surface energy. The [101] growth direction in our process also satisfies the lowest energy principle in thermodynamics due to change of (101) surface energy. A heterogeneous nucleation site was provided by the SiO x dismutation reaction, and the formation of core-shell (SnO2-SiO x ) structure should result from the phase separation energy. The free-standing coaxial SnO2-SiO x heterostructured nanorods grow by modification of the mass transfer coefficient. As-grown depositions show shrimp-like, flower-like, and worm-like morphologies under a higher mass transfer coefficient. Formation of the free-standing core-shell structure depends on the vertical growth mechanism.

  16. Coaxial tube array space transmission line characterization

    Science.gov (United States)

    Switzer, Colleen A.; Bents, David J.

    1987-01-01

    The coaxial tube array tether/transmission line used to connect an SP-100 nuclear power system to the space station was characterized over the range of reactor-to-platform separation distances of 1 to 10 km. Characterization was done with respect to array performance, physical dimensions and masses. Using a fixed design procedure, a family of designs was generated for the same power level (300 kWe), power loss (1.5 percent), and meteoroid survival probability (99.5 percent over 10 yr). To differentiate between vacuum insulated and gas insulated lines, two different maximum values of the E field were considered: 20 kV/cm (appropriate to vacuum insulation) and 50 kV/cm (compressed SF6). Core conductor, tube, bumper, standoff, spacer and bumper support dimensions, and masses were also calculated. The results of the characterization show mainly how transmission line size and mass scale with reactor-to-platform separation distance.

  17. Load-resistant coaxial transmission line

    Science.gov (United States)

    Hall, David R.; Fox, Joe

    2006-01-03

    A transmission line for downhole tools that make up all or part of a tool string for drilling and production of oil, gas, and geothermal wells that can withstand the dynamic gravitational forces and other accelerations associated with downhole excavations. The transmission line has a metal tube, or outer conductor, that houses a coaxial wire inner conductor. A non-metallic dielectric material is interposed between the inner and outer conductors. The outer and inner conductors and the dielectric are sufficiently compressed together so that independent motion between them is abated. Compression of the components of the transmission line may be achieved by drawing the transmission through one or more dies in order to draw down the outer conductor onto the dielectric, or by expanding the inner conductor against the dielectric using a mandrel or hydraulic pressure. Non-metallic bead segments may be used in aid of the compression necessary to resist the dynamic forces and accelerations of drilling.

  18. Substrate Integrated Evanescent Filters Employing Coaxial Stubs

    DEFF Research Database (Denmark)

    Zhurbenko, Vitaliy

    2015-01-01

    is designed, fabricated, and tested. The filter exhibits a transmission zero due to the implemented stubs. The problem of evanescent mode filter analysis is formulated in terms of conventional network concepts. This formulation is then used for modelling of the filters. Strategies to further miniaturization...... and small height of the waveguide. In this work, one of the realization methods of evanescent mode waveguides using a single layer substrate is considered. The method is based on the use of coaxial stubs as capacitive susceptances externally connected to a SIW. A microwave filter based on these principles...... of the microwave filter are discussed. The approach is useful in applications where a sharp roll-off at the upper stop-band is required....

  19. Giant persistent photoconductivity in BaTiO3/TiO2 heterostructures

    Science.gov (United States)

    Plodinec, Milivoj; Šantić, Ana; Zavašnik, Janez; Čeh, Miran; Gajović, Andreja

    2014-10-01

    The persistent photoconductivity (PPC) effect in nanotube arrays of barium titanate and TiO2 (BTO/TiO2NT) was studied at room temperature under daylight illumination. The BTO/TiO2NT heterostructures exhibited a giant PPC effect that was six orders of magnitude higher than the dark conductivity, followed by a slow relaxation for 3 h. The PPC in this material was explained by the existence of defects at the surfaces and the interfaces of the investigated heterostructures. The sample was prepared using a two-step synthesis: the anodization of a Ti-foil and a subsequent hydrothermal synthesis. The structural and electrical characteristics were studied by micro-Raman spectroscopy, field-emission-gun scanning electron microscopy, and impedance spectroscopy.

  20. Structure reconstruction of TiO2-based multi-wall nanotubes: first-principles calculations.

    Science.gov (United States)

    Bandura, A V; Evarestov, R A; Lukyanov, S I

    2014-07-28

    A new method of theoretical modelling of polyhedral single-walled nanotubes based on the consolidation of walls in the rolled-up multi-walled nanotubes is proposed. Molecular mechanics and ab initio quantum mechanics methods are applied to investigate the merging of walls in nanotubes constructed from the different phases of titania. The combination of two methods allows us to simulate the structures which are difficult to find only by ab initio calculations. For nanotube folding we have used (1) the 3-plane fluorite TiO2 layer; (2) the anatase (101) 6-plane layer; (3) the rutile (110) 6-plane layer; and (4) the 6-plane layer with lepidocrocite morphology. The symmetry of the resulting single-walled nanotubes is significantly lower than the symmetry of initial coaxial cylindrical double- or triple-walled nanotubes. These merged nanotubes acquire higher stability in comparison with the initial multi-walled nanotubes. The wall thickness of the merged nanotubes exceeds 1 nm and approaches the corresponding parameter of the experimental patterns. The present investigation demonstrates that the merged nanotubes can integrate the two different crystalline phases in one and the same wall structure.

  1. Synthesis of Platinum Nanotubes and Nanorings via Simultaneous Metal Alloying and Etching

    KAUST Repository

    Huang, Zhiqi

    2016-04-19

    Metallic nanotubes represent a class of hollow nanostructures with unique catalytic properties. However, the wet-chemical synthesis of metallic nanotubes remains a substantial challenge, especially for those with dimensions below 50 nm. This communication describes a simultaneous alloying-etching strategy for the synthesis of Pt nanotubes with open ends by selective etching Au core from coaxial Au/Pt nanorods. This approach can be extended for the preparation of Pt nanorings when Saturn-like Au core/Pt shell nanoparticles are used. The diameter and wall thickness of both nanotubes and nanorings can be readily controlled in the range of 14-37 nm and 2-32 nm, respectively. We further demonstrated that the nanotubes with ultrathin side walls showed superior catalytic performance in oxygen reduction reaction. © 2016 American Chemical Society.

  2. Effect of Size-Dependent Thermal Instability on Synthesis of Zn2 SiO4-SiOx Core–Shell Nanotube Arrays and Their Cathodoluminescence Properties

    Directory of Open Access Journals (Sweden)

    Dierre Benjamin

    2010-01-01

    Full Text Available Abstract Vertically aligned Zn2SiO4-SiOx(x < 2 core–shell nanotube arrays consisting of Zn2SiO4-nanoparticle chains encapsulated into SiOx nanotubes and SiOx-coated Zn2SiO4 coaxial nanotubes were synthesized via one-step thermal annealing process using ZnO nanowire (ZNW arrays as templates. The appearance of different nanotube morphologies was due to size-dependent thermal instability and specific melting of ZNWs. With an increase in ZNW diameter, the formation mechanism changed from decomposition of “etching” to Rayleigh instability and then to Kirkendall effect, consequently resulting in polycrystalline Zn2SiO4-SiOx coaxial nanotubes, single-crystalline Zn2SiO4-nanoparticle-chain-embedded SiOx nanotubes, and single-crystalline Zn2SiO4-SiOx coaxial nanotubes. The difference in spatially resolved optical properties related to a particular morphology was efficiently documented by means of cathodoluminescence (CL spectroscopy using a middle-ultraviolet emission at 310 nm from the Zn2SiO4 phase.

  3. Spatial properties of coaxial superposition of two coherent Gaussian beams

    CSIR Research Space (South Africa)

    Boubaha, B

    2013-08-01

    Full Text Available In this paper, we explore theoretically and experimentally the laser beam shaping ability resulting from the coaxial superposition of two coherent Gaussian beams (GBs). This technique is classified under interferometric laser beam shaping techniques...

  4. Swirl Coaxial Injector Development. Part II: CFD Modeling

    National Research Council Canada - National Science Library

    Cheng, G

    2002-01-01

    .... Therefore, swirl coaxial injectors, which swirl liquid fuel around a gaseous oxygen core, show promise for the next generation of high performance staged combustion rocket engines utilizing hydrocarbon fuels...

  5. X-Ray Radiography Measurements of Shear Coaxial Rocket Injectors

    Science.gov (United States)

    2013-02-01

    CH4/LOX engines using a fuel regeneratively cooled combustion chamber . Previous coaxial jet research can be divided by the phase of the two...Approved for public release; distribution unlimited. Clearance # 2 Introduction Due to their utility in a number of combustion de- vices...transients of boost-class engines. The current work focuses on this multiphase type of jet. Previous studies on two-phase coaxial jets have been more lim

  6. Separation of Particles in Swirling Flow in Coaxial Channel

    Directory of Open Access Journals (Sweden)

    Vasilevsky Michail

    2016-01-01

    Full Text Available Cyclones are widely used devices to separate a dispersed phase (e.g. particles or droplets from a continuous phase. The separation of particles in coaxial channels with different length is considered in paper. In this study we show that as coaxial channels length grows, the efficiency increases. In addition we demonstrate that as a gap between cylinder components is reduced, the aerosol spray efficiency is reduced also in turbulent flow.

  7. Nanotube cathodes.

    Energy Technology Data Exchange (ETDEWEB)

    Overmyer, Donald L.; Lockner, Thomas Ramsbeck; Siegal, Michael P.; Miller, Paul Albert

    2006-11-01

    Carbon nanotubes have shown promise for applications in many diverse areas of technology. In this report we describe our efforts to develop high-current cathodes from a variety of nanotubes deposited under a variety of conditions. Our goal was to develop a one-inch-diameter cathode capable of emitting 10 amperes of electron current for one second with an applied potential of 50 kV. This combination of current and pulse duration significantly exceeds previously reported nanotube-cathode performance. This project was planned for two years duration. In the first year, we tested the electron-emission characteristics of nanotube arrays fabricated under a variety of conditions. In the second year, we planned to select the best processing conditions, to fabricate larger cathode samples, and to test them on a high-power relativistic electron beam generator. In the first year, much effort was made to control nanotube arrays in terms of nanotube diameter and average spacing apart. When the project began, we believed that nanotubes approximately 10 nm in diameter would yield sufficient electron emission properties, based on the work of others in the field. Therefore, much of our focus was placed on measured field emission from such nanotubes grown on a variety of metallized surfaces and with varying average spacing between individual nanotubes. We easily reproduced the field emission properties typically measured by others from multi-wall carbon nanotube arrays. Interestingly, we did this without having the helpful vertical alignment to enhance emission; our nanotubes were randomly oriented. The good emission was most likely possible due to the improved crystallinity, and therefore, electrical conductivity, of our nanotubes compared to those in the literature. However, toward the end of the project, we learned that while these 10-nm-diameter CNTs had superior crystalline structure to the work of others studying field emission from multi-wall CNT arrays, these nanotubes still

  8. Electrical transport and photovoltaic effects of core-shell CuO/C60 nanowire heterostructure.

    Science.gov (United States)

    Bao, Qiaoliang; Li, Chang Ming; Liao, Lei; Yang, Hongbin; Wang, Wei; Ke, Chang; Song, Qunliang; Bao, Haifeng; Yu, Ting; Loh, Kian Ping; Guo, Jun

    2009-02-11

    An organic/inorganic hybrid heterostructure consisting of p-type CuO nanowire core and n-type C(60) shell was fabricated and its electrical transport properties were studied for the first time. It was found that the devices with contacts on shell-shell show an ohmic behavior but the devices with contacts on core-shell forms a single p-n junction and display a rectifying behavior. Logarithmic current-voltage curves at various temperatures show that the tunneling transport plays a critical role in the electrical transport. Photovoltaic effects were observed in the core-shell contacted CuO/C(60) junctions under illumination. This work demonstrates that an inorganic/organic coaxial nanowire can provide potential in nanoelectronic devices and could further stack high density hybrid nanowires array as a renewable power source.

  9. Electrical transport and photovoltaic effects of core-shell CuO/C60 nanowire heterostructure

    Science.gov (United States)

    Bao, Qiaoliang; Li, Chang Ming; Liao, Lei; Yang, Hongbin; Wang, Wei; Ke, Chang; Song, Qunliang; Bao, Haifeng; Yu, Ting; Loh, Kian Ping; Guo, Jun

    2009-02-01

    An organic/inorganic hybrid heterostructure consisting of p-type CuO nanowire core and n-type C60 shell was fabricated and its electrical transport properties were studied for the first time. It was found that the devices with contacts on shell-shell show an ohmic behavior but the devices with contacts on core-shell forms a single p-n junction and display a rectifying behavior. Logarithmic current-voltage curves at various temperatures show that the tunneling transport plays a critical role in the electrical transport. Photovoltaic effects were observed in the core-shell contacted CuO/C60 junctions under illumination. This work demonstrates that an inorganic/organic coaxial nanowire can provide potential in nanoelectronic devices and could further stack high density hybrid nanowires array as a renewable power source.

  10. Surface Plasmons in Coaxial Metamaterial Cables

    Science.gov (United States)

    Kushwaha, Manvir S.; Djafari-Rouhani, Bahram

    2013-07-01

    Thanks to Victor Veselago for his hypothesis of negative index of refraction, meta-materials — engineered composites — can be designed to have properties difficult or impossible to find in nature: they can have both electrical permittivity (ɛ) and magnetic permeability (μ) simultaneously negative. The metamaterials — henceforth negative-index materials (NIMs) — owe their properties to subwavelength structure rather than to their chemical composition. The tailored electromagnetic response of the NIMs has had a dramatic impact on classical optics: they are becoming known to have changed many basic notions related with electromagnetism. The present article is focused on gathering and reviewing fundamental characteristics of plasmon propagation in coaxial cables fabricated of the right-handed medium (RHM) (with ɛ > 0, μ > 0) and the left-handed medium (LHM) (with ɛ cloaking devices in particular. A recent surge in efforts on invisibility and the cloaking devices seems to have spoiled the researchers worldwide: proposals include not only a way to hide an object without having to wrap the cloak around it, but also to replace a given object with another, thus adding to the deception even further! All this is attributed as much to the fundamental as to the practical advances made in the fabrication and characterization of NIMs. The article concludes briefly addressing the anticipated implications of plasmon observation in the multicoaxial cables and suggesting future dimensions worth adding to the problem. The background provided is believed to make less formidable the task of future writers of reviews in this field.

  11. Optimizing the Ranchero Coaxial Flux Compression Generator

    Energy Technology Data Exchange (ETDEWEB)

    Tasker, D.G.; Goforth, J.H.; Fowler, C.M.; Lopez, E.A.; Oona, H.; King, J.C.; Herrera, D.H.; Torres, D.T.; Reinovsky, R.E.; Martinez, E.C.; Stokes, J.L.; Tabaka, L.J.; Garcia, O.F.; Atchison, W.L.; Faehl, R.J.; Lindemuth, I.R.; Keinigs, R.K.; Miller, P.J.

    1998-10-18

    Ranchero is an explosively driven magnetic flux-compression generator that has been developed, over the last four years, as a versatile power source for high energy density physics experiments. It is coaxial, and comprises a 15 cm-diameter armature and a 30-cm stator, each aluminum. The length may be varied to suit the demands of each experiment; thus far, lengths of 0.43 m and 1.4 m have been used. The stator is filled and driven by a high performance cast explosive, and the ultimate performance of the device is limited by the smoothness of the armature expansion. The armature explosive is initiated on axis by PETN hemispheres, spaced at intervals of about 18 mm and 24.5 mm; each is simultaneously detonated by a slapper detonator system. Calculations of armature expansion predicted ripples less than 0.2 mm, and this was confirmed in early experiments. Yet, ripples approaching tens of millimeters were observed in some more recent experiments. The authors discuss the possible origins of the se large ripples, and the methods the authors have used to correct them.

  12. EUO-Based Multifunctional Heterostructures

    Science.gov (United States)

    2015-06-06

    MULTIFUNCTIONAL HETEROSTRUCTURES Final Report (June, 2015) 5 5 A. Melville, T. Mairoser, A. Schmehl, D.E. Shai, E.J. Monkman, J.W. Harter , T. Heeg...Europium Oxide,” J. Appl. Phys. 109 (2011) 07C309. 13 D.E. Shai, A.J. Melville, J.W. Harter , E.J. Monkman, D.W. Shen, A. Schmehl, D.G. Schlom, and...A. Schmehl, D.E. Shai, E.J. Monkman, J.W. Harter , T. Heeg, B. Holländer, J. Schubert, K.M. Shen, J. Mannhart, and D.G. Schlom, “Lutetium-doped EuO

  13. Nanotube phonon waveguide

    Science.gov (United States)

    Chang, Chih-Wei; Zettl, Alexander K.

    2013-10-29

    Disclosed are methods and devices in which certain types of nanotubes (e.g., carbon nanotubes and boron nitride nanotubes conduct heat with high efficiency and are therefore useful in electronic-type devices.

  14. Nanotube News

    Science.gov (United States)

    Journal of College Science Teaching, 2005

    2005-01-01

    Smaller, faster computers, bullet-proof t-shirts, and itty-bitty robots--such are the promises of nanotechnology and the cylinder-shaped collection of carbon molecules known as nanotubes. But for these exciting ideas to become realities, scientists must understand how these miracle molecules perform under all sorts of conditions. This brief…

  15. Chiral Nanotubes

    Directory of Open Access Journals (Sweden)

    Andrea Nitti

    2017-07-01

    Full Text Available Organic nanotubes, as assembled nanospaces, in which to carry out host–guest chemistry, reversible binding of smaller species for transport, sensing, storage or chemical transformation purposes, are currently attracting substantial interest, both as biological ion channel mimics, or for addressing tailored material properties. Nature’s materials and machinery are universally asymmetric, and, for chemical entities, controlled asymmetry comes from chirality. Together with carbon nanotubes, conformationally stable molecular building blocks and macrocycles have been used for the realization of organic nanotubes, by means of their assembly in the third dimension. In both cases, chiral properties have started to be fully exploited to date. In this paper, we review recent exciting developments in the synthesis and assembly of chiral nanotubes, and of their functional properties. This review will include examples of either molecule-based or macrocycle-based systems, and will try and rationalize the supramolecular interactions at play for the three-dimensional (3D assembly of the nanoscale architectures.

  16. Stabilized thin film heterostructure for electrochemical applications

    DEFF Research Database (Denmark)

    2015-01-01

    The invention provides a method for the formation of a thin film multi-layered heterostructure upon a substrate, said method comprising the steps of: a. providing a substrate; b. depositing a buffer layer upon said substrate, said buffer layer being a layer of stable ionic conductor (B); c...... or less; and e. repeating steps b. and c. a total of N times, such that N repeating pairs of layers (A/B) are built up, wherein N is 1 or more. The invention also provides a thin film multi-layered heterostructure as such, and the combination of a thin film multi-layered heterostructure and a substrate...

  17. Swirl Coaxial Injector Testing with LOX/RP-J

    Science.gov (United States)

    Greene, Sandra Elam; Casiano, Matt

    2013-01-01

    Testing was conducted at NASA fs Marshall Space Flight Center (MSFC) in the fall of 2012 to evaluate the operation and performance of liquid oxygen (LOX) and kerosene (RP ]1) in an existing swirl coaxial injector. While selected Russian engines use variations of swirl coaxial injectors, component level performance data has not been readily available, and all previously documented component testing at MSFC with LOX/RP ]1 had been performed using a variety of impinging injector designs. Impinging injectors have been adequate for specific LOX/RP ]1 engine applications, yet swirl coaxial injectors offer easier fabrication efforts, providing cost and schedule savings for hardware development. Swirl coaxial elements also offer more flexibility for design changes. Furthermore, testing with LOX and liquid methane propellants at MSFC showed that a swirl coaxial injector offered improved performance compared to an impinging injector. So, technical interest was generated to see if similar performance gains could be achieved with LOX/RP ]1 using a swirl coaxial injector. Results would allow such injectors to be considered for future engine concepts that require LOX/RP ]1 propellants. Existing injector and chamber hardware was used in the test assemblies. The injector had been tested in previous programs at MSFC using LOX/methane and LOX/hydrogen propellants. Minor modifications were made to the injector to accommodate the required LOX/RP ]1 flows. Mainstage tests were performed over a range of chamber pressures and mixture ratios. Additional testing included detonated gbombs h for stability data. Test results suggested characteristic velocity, C*, efficiencies for the injector were 95 ]97%. The injector also appeared dynamically stable with quick recovery from the pressure perturbations generated in the bomb tests.

  18. Snaps to Connect Coaxial and Microstrip Lines in Wearable Systems

    Directory of Open Access Journals (Sweden)

    Tiiti Kellomäki

    2012-01-01

    Full Text Available Commercial snaps (clothing fasteners can be used to connect a coaxial cable to a microstrip line. This is useful in the context of wearable antennas, especially in consumer applications and disposable connections. The measured S-parameters of the transition are presented, and an equivalent circuit and approximate equations are derived for system design purposes. The proposed connection is usable up to 1.5 GHz (10 dB return loss condition, and the frequency range can be extended to 2 GHz if a thinner, more flexible coaxial cable is used.

  19. CIRUGÍA DE CATARATA POR MICROINCISIONES BIMANUALES Y COAXIALES

    OpenAIRE

    Juan Raúl Hernández Silva; Meisy Ramos López; Marcelino Rio Torres; Yanele Ruíz Rodríguez; Raúl Rúa Martínez

    2012-01-01

    Objetivo: Comparar los resultados de la cirugía de catarata por las técnicas de microincisiones coaxiales y microincisiones bimanuales en el Instituto Cubano de Oftalmología “Ramón Pando Ferrer” en el período de junio de 2009 a junio de 2011. Métodos: Los pacientes fueron diagnosticados con catarata senil o presenil. De estos, 41 pacientes se operaron con la técnica de microincisiones coaxiales y 27 pacientes con la técnica de microincisiones bimanuales. Se determinó: edad, dureza del cristal...

  20. Experimental seismic test of fluid coupled co-axial cylinders

    Energy Technology Data Exchange (ETDEWEB)

    Chu, M. L.; Brown, S. J.; Lestingi, J. F.

    1979-01-01

    The dynamic response of fluid coupled coaxial cylindrical shells is of interest to the nuclear industry with respect to the seismic design of the reactor vessel and thermal liner. The experiments described present a series of tests which investigate the effect of the annular clearance between the cylinders (gap) on natural frequency, damping, and seismic response of both the inner and outer cylinders. The seismic input is a time history base load to the flexible fluid filled coaxial cylinders. The outer cylinder is elastically supported at both ends while the inner cylinder is supported only at the base (lower) end.

  1. Carbon nanotubes

    OpenAIRE

    SLOBODAN N. MARINKOVIC

    2008-01-01

    Nanotubes, the last in the focus of scientists in a series of “all carbon” materials discovered over the last several decades are the most interesting and have the greatest potential. This review aims at presenting in a concise manner the considerable amount of knowledge accumulated since the discovery of this amazing form of solid carbon, particularly during the last 15 years. The topics include methods of synthesis, mathematical description, characterization by Raman spectroscopy, most impo...

  2. Carbon nanotube composite materials

    Science.gov (United States)

    O'Bryan, Gregory; Skinner, Jack L; Vance, Andrew; Yang, Elaine Lai; Zifer, Thomas

    2015-03-24

    A material consisting essentially of a vinyl thermoplastic polymer, un-functionalized carbon nanotubes and hydroxylated carbon nanotubes dissolved in a solvent. Un-functionalized carbon nanotube concentrations up to 30 wt % and hydroxylated carbon nanotube concentrations up to 40 wt % can be used with even small concentrations of each (less than 2 wt %) useful in producing enhanced conductivity properties of formed thin films.

  3. Online monitoring of biofouling using coaxial stub resonator technique

    NARCIS (Netherlands)

    Hoog-Antonyuk, N.A.; Mayer, M.J.J.; Miedema, H.; Olthuis, Wouter; Tomaszweska, A.A.; Paulitsch-Fuchs, A.H.; van den Berg, Albert

    Here we demonstrate the proof-of-principle that a coaxial stub resonator can be used to detect early stages of biofilm formation. After promising field tests using a stub resonator with a stainless steel inner conductor as sensitive element, the sensitivity of the system was improved by using a

  4. A model for ferrite-loaded transversely biased coaxial resonators

    DEFF Research Database (Denmark)

    Acar, Öncel; Zhurbenko, Vitaliy; Johansen, Tom Keinicke

    2013-01-01

    This work describes a simple model for shortened coaxial cavity resonators with transversely biased ferrite elements. The ferrite allows the resonance frequency to be tuned, and the presented model provides a method of approximately calculating these frequencies to generate the tuning curve...

  5. Review of Combustion Stability Characteristics of Swirl Coaxial Element Injectors

    Science.gov (United States)

    Hulka, J. R.; Casiano, M. J.

    2013-01-01

    Liquid propellant rocket engine injectors using coaxial elements where the center liquid is swirled have become more common in the United States over the past several decades, although primarily for technology or advanced development programs. Currently, only one flight engine operates with this element type in the United States (the RL10 engine), while the element type is very common in Russian (and ex-Soviet) liquid propellant rocket engines. In the United States, the understanding of combustion stability characteristics of swirl coaxial element injectors is still very limited, despite the influx of experimental and theoretical information from Russia. The empirical and theoretical understanding is much less advanced than for the other prevalent liquid propellant rocket injector element types, the shear coaxial and like-on-like paired doublet. This paper compiles, compares and explores the combustion stability characteristics of swirl coaxial element injectors tested in the United States, dating back to J-2 and RL-10 development, and extending to very recent programs at the NASA MSFC using liquid oxygen and liquid methane and kerosene propellants. Included in this study are several other relatively recent design and test programs, including the Space Transportation Main Engine (STME), COBRA, J-2X, and the Common Extensible Cryogenic Engine (CECE). A presentation of the basic data characteristics is included, followed by an evaluation by several analysis techniques, including those included in Rocket Combustor Interactive Design and Analysis Computer Program (ROCCID), and methodologies described by Hewitt and Bazarov.

  6. Evaluating efficiency of coaxial MLC VMAT plan for spine SBRT

    Energy Technology Data Exchange (ETDEWEB)

    Son, Sang Jun; Mun, Jun Ki; Kim, Dae Ho; Yoo, Suk Hyun [Dept. of Radiation Oncology, Seoul National University Hospital, Seoul (Korea, Republic of)

    2014-12-15

    The purpose of the study is to evaluate the efficiency of Coaxial MLC VMAT plan (Using 273° and 350° collimator angle) That the leaf motion direction aligned with axis of OAR (Organ at risk, It means spinal cord or cauda equine in this study.) compare to Universal MLC VMAT plan (using 30° and 330 ° collimator angle) for spine SBRT. The 10 cases of spine SBRT that treated with VMAT planned by Coaxial MLC and Varian TBX were enrolled. Those cases were planned by Eclipse (Ver. 10.0.42, Varian, USA), PRO3 (Progressive Resolution Optimizer 10.0.28) and AAA (Anisotropic Analytic Algorithm Ver. 10.0.28) with coplanar 260 ° arcs and 10MV FFF (Flattening filter free). Each arc has 273° and 350 ° collimator angle, respectively. The Universal MLC VMAT plans are based on existing treatment plans. Those plans have the same parameters of existing treatment plans but collimator angle. To minimize the dose difference that shows up randomly on optimizing, all plans were optimized and calculated twice respectively. The calculation grid is 0.2 cm and all plans were normalized to the target V100%=90%. The indexes of evaluation are V10Gy, D0.03cc, Dmean of OAR (Organ at risk, It means spinal cord or cauda equine in this study.), H.I (Homogeneity index) of the target and total MU. All Coaxial VMAT plans were verified by gamma test with Mapcheck2 (Sun Nuclear Co., USA), Mapphan (Sun Nuclear Co., USA) and SNC patient (Sun Nuclear Co., USA Ver 6.1.2.18513). The difference between the coaxial and the universal VMAT plans are follow. The coaxial VMAT plan is better in the V10Gy of OAR, Up to 4.1%, at least 0.4%, the average difference was 1.9% and In the D0.03cc of OAR, Up to 83.6 cGy, at least 2.2 cGy, the average difference was 33.3 cGy. In Dmean, Up to 34.8 cGy, at least -13.0 cGy, the average difference was 9.6 cGy that say the coaxial VMAT plans are better except few cases. H.I difference Up to 0.04, at least 0.01, the average difference was 0.02 and the difference of average

  7. Vertical-Cavity In-plane Heterostructures: Physics and Applications

    DEFF Research Database (Denmark)

    Taghizadeh, Alireza; Mørk, Jesper; Chung, Il-Sug

    2015-01-01

    We show that the in-plane heterostructures realized in vertical cavities with high contrast grating(HCG) reflector enables exotic configurations of heterostructure and photonic wells. In photonic crystal heterostructures forming a photonic well, the property of a confined mode is determined by th...... to discuss the rich potential of this heterostructure as a platform for various physics studies and propose a system of two laterally coupled cavities which shows the breaking of parity-time symmetry as an example....

  8. Near white light emission and enhanced photocatalytic activity by tweaking surface defects of coaxial ZnO@ZnS core-shell nanorods

    Science.gov (United States)

    Kumbhakar, Partha; Biswas, Subrata; Tiwary, Chandra S.; Kumbhakar, Pathik

    2017-04-01

    The enhancement in the emission of visible light in the synthesized coaxial ZnO@ZnS core-shell nanorods (CSNR) has led to the development of a nearly white light-emitting photoluminescent material as confirmed by the calculation of Commission Internationale de l'Eclairage chromaticity coordinates. However, we have fabricated a nearly white light-emitting diode (WLED) by combining a commercial UV LED chip with our CSNR material, and it emits warm white light. The observed increase in the relative intensity of deep level (IDLE) over UV (IUV) photoluminescence emission is attributed to the addition of new defect states during the formation of the shell with a larger thickness as becomes evident from X-ray photoelectron spectroscopy (XPS) study. Thanks to the presence of such defect states, whose effective exploitation enabled us to obtain ˜93% photodegradation of a test dye, namely, methylene blue, in the presence of core-shell ZnO@ZnS heterostructure within only 25 min of irradiation of UV-Visible light. Thus, apart from demonstrating the fabrication of a near WLED, we have successfully demonstrated the enhanced photocatalytic performance by tweaking the surface defects of ZnO nanorods via the formation of coaxial ZnO@ZnS core-shell nanorods with various shell thicknesses.

  9. Transport of photogenerated charges and photoelectric properties in two types of heterostructures with different ZnO microstructures.

    Science.gov (United States)

    Liu, Xiangyang; Cheng, Xiuying; Wang, Shun; Zhang, Kun; Gu, Yuzong

    2015-07-14

    ZnO films with several microstructures including nanoparticles, nanowire arrays, nanorod arrays and nanotube arrays were prepared using different methods. In2O3 and/or Cu4Bi4S9 were deposited onto each nanostructured ZnO film, and two types of heterostructures (ZnO/Cu4Bi4S9 and ZnO/In2O3/Cu4Bi4S9) as well as solid state dye-sensitized solar cells were fabricated. The signals of steady state and electric field-induced surface photovoltage spectroscopy indicate that all of ZnO/In2O3/Cu4Bi4S9 heterostructures exhibit higher photovoltaic response than the relative ZnO/Cu4Bi4S9. The same type of heterostructure with different ZnO films presents various photovoltaic properties. Transient surface photovoltage spectroscopy can contribute to study the separation and transport mechanism of photogenerated charges. Here, ZnO nanotubes/Cu4Bi4S9 and ZnO nanotubes/In2O3/Cu4Bi4S9 cells exhibit the best performances with the highest efficiencies of 6.2% and 6.8%, respectively. The internal relations of photoelectric properties to some factors, such as film thickness, surface area, microstructure, double energy level matchings, etc. were discussed in detail. Qualitative and quantitative analysis further verified the comprehensive effect and the difference of factors. The exploration to understand the transport mechanism of light-induced charges in composite films will promote the nanocrystal application in solid state solar cells and photovoltaic community.

  10. Single-layer graphene-TiO{sub 2} nanotubes array heterojunction for ultraviolet photodetector application

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Deng-Yue [School of Material Sciences and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Ge, Cai-Wang [School of Electronic Science and Applied Physics, Hefei University of Technology, Hefei, Anhui 230009 (China); Wang, Jiu-Zhen [School of Material Sciences and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Zhang, Teng-Fei [School of Electronic Science and Applied Physics, Hefei University of Technology, Hefei, Anhui 230009 (China); Wu, Yu-Cheng, E-mail: ycwu@hfut.edu.cn [School of Material Sciences and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Liang, Feng-Xia, E-mail: fxliang@hfut.edu.cn [School of Material Sciences and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China)

    2016-11-30

    Highlights: • Heterostructures comprised of a single-layer graphene and TiO{sub 2} nanotube arrays were constructed for ultraviolet detection. • The electrical properties of the fabricated heterostructures were dependent on the annealing atmospheres. • The effect of anodic TiO{sub 2} nanotube length on the performance of the photodetector were investigated. - Abstract: In this work, we reported on the fabrication of a single-layer graphene (SLG)-TiO{sub 2} nanotube arrays (NTs) heterostructures ultraviolet photodetector (UVPD) by transferring chemical vapor deposition derived MLG on the surface of anodic TiO{sub 2}NTs array. Through varying the annealing atmosphere and anodization time in the TiO{sub 2} synthesis procedure, the electronic and optoelectronic properties of the as-fabricated Schottky junction UVPD were studied. It was revealed that the anodic TiO{sub 2}NTs annealed in air showed a better rectifying behavior and was highly sensitive to UV light irradiation. Further investigation found that the device performance of the UVPD can be readily modulated by the anodization time, and the anodic TiO{sub 2}NTs with a medium tube length of 9.6 μm exhibits the highest device performance. These results demonstrated that the present SLG-TiO{sub 2}NTs array hetero-junction UVPD will be highly promising for fabricating high-performance optoelectronic device and system in the future.

  11. Terahertz semiconductor-heterostructure laser.

    Science.gov (United States)

    Köhler, Rüdeger; Tredicucci, Alessandro; Beltram, Fabio; Beere, Harvey E; Linfield, Edmund H; Davies, A Giles; Ritchie, David A; Iotti, Rita C; Rossi, Fausto

    2002-05-09

    Semiconductor devices have become indispensable for generating electromagnetic radiation in everyday applications. Visible and infrared diode lasers are at the core of information technology, and at the other end of the spectrum, microwave and radio-frequency emitters enable wireless communications. But the terahertz region (1-10 THz; 1 THz = 10(12) Hz) between these ranges has remained largely underdeveloped, despite the identification of various possible applications--for example, chemical detection, astronomy and medical imaging. Progress in this area has been hampered by the lack of compact, low-consumption, solid-state terahertz sources. Here we report a monolithic terahertz injection laser that is based on interminiband transitions in the conduction band of a semiconductor (GaAs/AlGaAs) heterostructure. The prototype demonstrated emits a single mode at 4.4 THz, and already shows high output powers of more than 2 mW with low threshold current densities of about a few hundred A cm(-2) up to 50 K. These results are very promising for extending the present laser concept to continuous-wave and high-temperature operation, which would lead to implementation in practical photonic systems.

  12. Manipulation of magnetic exchange in iridate heterostructures

    Science.gov (United States)

    Meyers, D.; Fabbris, G.; Yin, Weiguo; Casa, D.; Cao, Yue; Hao, Lin; Schmitt, T.; Liu, Jian; Dean, M. P. M.

    Artificial layering of disparate materials into superlattices is an emerging method that promises unparalleled versatility in accessing ground states unavailable to bulk synthesis. Heterostructures composed of paramagnetic, metallic SrIrO3 interspaced with band insulating SrTiO3 were found to host a canted antiferromagnetic ground state, mirroring the Ruddlesen-Popper series iridates with enhanced tunability. We investigate the magnetic excitation spectrum of these artificial systems using resonant inelastic x-ray scattering and directly infer the interlayer and intralayer magnetic exchange interactions. Understanding how interfacial effects modify magnetic interactions is a vital prerequisite for efforts to controllably target different ground states within complex oxide-heterostructures.

  13. Carbon nanotube nanoelectrode arrays

    Science.gov (United States)

    Ren, Zhifeng; Lin, Yuehe; Yantasee, Wassana; Liu, Guodong; Lu, Fang; Tu, Yi

    2008-11-18

    The present invention relates to microelectode arrays (MEAs), and more particularly to carbon nanotube nanoelectrode arrays (CNT-NEAs) for chemical and biological sensing, and methods of use. A nanoelectrode array includes a carbon nanotube material comprising an array of substantially linear carbon nanotubes each having a proximal end and a distal end, the proximal end of the carbon nanotubes are attached to a catalyst substrate material so as to form the array with a pre-determined site density, wherein the carbon nanotubes are aligned with respect to one another within the array; an electrically insulating layer on the surface of the carbon nanotube material, whereby the distal end of the carbon nanotubes extend beyond the electrically insulating layer; a second adhesive electrically insulating layer on the surface of the electrically insulating layer, whereby the distal end of the carbon nanotubes extend beyond the second adhesive electrically insulating layer; and a metal wire attached to the catalyst substrate material.

  14. Plasmonic Colour Filters Based on Coaxial Holes in Aluminium

    Directory of Open Access Journals (Sweden)

    Ranjith Rajasekharan Unnithan

    2017-04-01

    Full Text Available Aluminum is an alternative plasmonic material in the visible regions of the spectrum due to its attractive properties such as low cost, high natural abundance, ease of processing, and complementary metal-oxide-semiconductor (CMOS and liquid crystal display (LCD compatibility. Here, we present plasmonic colour filters based on coaxial holes in aluminium that operate in the visible range. Using both computational and experimental methods, fine-tuning of resonance peaks through precise geometric control of the coaxial holes is demonstrated. These results will lay the basis for the development of filters in high-resolution liquid crystal displays, RGB-spatial light modulators, liquid crystal over silicon devices and novel displays.

  15. Coaxial vacuum gap breakdown for pulsed power liners

    Science.gov (United States)

    Cordaro, S. W.; Bott-Suzuki, S. C.; Caballero Bendixsen, L. S.; Haas, D. M.; Meisenhelder, C.

    2014-12-01

    Recent work conducted at UC San Diego utilizes a high voltage system, up to 25kV, to study and analyze the vacuum breakdown mechanisms of a coaxial gap. An analysis of the coaxial gap has utilized laser interferometry for density profile, as well as magnetic field measurements via B-dot probes. Results show that breakdown is random about the azimuth, and that density of breakdown plasma is low (˜ne dl probe(s) closest to where breakdown occurs making it possible to triangulate the relative position breakdown occurred without the need for line of sight along the axis. Furthermore, diagnostic results coupled with the unpolished electrodes being at room temperature suggests that field emission is the dominant mechanism causing initial breakdown.

  16. Non-coaxial superposition of vector vortex beams.

    Science.gov (United States)

    Aadhi, A; Vaity, Pravin; Chithrabhanu, P; Reddy, Salla Gangi; Prabakar, Shashi; Singh, R P

    2016-02-10

    Vector vortex beams are classified into four types depending upon spatial variation in their polarization vector. We have generated all four of these types of vector vortex beams by using a modified polarization Sagnac interferometer with a vortex lens. Further, we have studied the non-coaxial superposition of two vector vortex beams. It is observed that the superposition of two vector vortex beams with same polarization singularity leads to a beam with another kind of polarization singularity in their interaction region. The results may be of importance in ultrahigh security of the polarization-encrypted data that utilizes vector vortex beams and multiple optical trapping with non-coaxial superposition of vector vortex beams. We verified our experimental results with theory.

  17. COAXIAL TWO-CHANNEL DIELECTRIC WAKE FIELD ACCELERATOR

    Energy Technology Data Exchange (ETDEWEB)

    Hirshfield, Jay L. [Omega-P, Inc.

    2013-04-30

    Theory, computations, and experimental apparatus are presented that describe and are intended to confirm novel properties of a coaxial two-channel dielectric wake field accelerator. In this configuration, an annular drive beam in the outer coaxial channel excites multimode wakefields which, in the inner channel, can accelerate a test beam to an energy much higher than the energy of the drive beam. This high transformer ratio is the result of judicious choice of the dielectric structure parameters, and of the phase separation between drive bunches and test bunches. A structure with cm-scale wakefields has been build for tests at the Argonne Wakefield Accelerator Laboratory, and a structure with mm-scale wakefields has been built for tests at the SLAC FACET facility. Both tests await scheduling by the respective facilities.

  18. Risk factor analysis of pulmonary hemorrhage complicating CT-guided lung biopsy in coaxial and non-coaxial core biopsy techniques in 650 patients

    Energy Technology Data Exchange (ETDEWEB)

    Nour-Eldin, Nour-Eldin A., E-mail: nour410@hotmail.com [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Diagnostic and Interventional Radiology Department, Cairo University Hospital, Cairo (Egypt); Alsubhi, Mohammed [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Naguib, Nagy N. [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Diagnostic and Interventional Radiology Department, Alexandria University Hospital, Alexandria (Egypt); Lehnert, Thomas; Emam, Ahmed; Beeres, Martin; Bodelle, Boris; Koitka, Karen; Vogl, Thomas J.; Jacobi, Volkmar [Institute for Diagnostic and Interventional Radiology, Johan Wolfgang Goethe – University Hospital, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany)

    2014-10-15

    Purpose: To evaluate the risk factors involved in the development of pulmonary hemorrhage complicating CT-guided biopsy of pulmonary lesions in coaxial and non-coaxial techniques. Materials and methods: Retrospective study included CT-guided percutaneous lung biopsies in 650 consecutive patients (407 males, 243 females; mean age 54.6 years, SD: 5.2) from November 2008 to June 2013. Patients were classified according to lung biopsy technique in coaxial group (318 lesions) and non-coaxial group (332 lesions). Exclusion criteria for biopsy were: lesions <5 mm in diameter, uncorrectable coagulopathy, positive-pressure ventilation, severe respiratory compromise, pulmonary arterial hypertension or refusal of the procedure. Risk factors for pulmonary hemorrhage complicating lung biopsy were classified into: (a) patient's related risk factors, (b) lesion's related risk factors and (d) technical risk factors. Radiological assessments were performed by two radiologists in consensus. Mann–Whitney U test and Fisher's exact tests for statistical analysis. p values <0.05 were considered statistically significant. Results: Incidence of pulmonary hemorrhage was 19.6% (65/332) in non-coaxial group and 22.3% (71/318) in coaxial group. The difference in incidence between both groups was statistically insignificant (p = 0.27). Hemoptysis developed in 5.4% (18/332) and in 6.3% (20/318) in the non-coaxial and coaxial groups respectively. Traversing pulmonary vessels in the needle biopsy track was a significant risk factor of the development pulmonary hemorrhage (incidence: 55.4% (36/65, p = 0.0003) in the non-coaxial group and 57.7% (41/71, p = 0.0013) in coaxial group). Other significant risk factors included: lesions of less than 2 cm (p value of 0.01 and 0.02 in non-coaxial and coaxial groups respectively), basal and middle zonal lesions in comparison to upper zonal lung lesions (p = 0.002 and 0.03 in non-coaxial and coaxial groups respectively), increased lesion

  19. MPROVEMENT OF TECHNOLOGY OF PRODUCTION OF COAXIAL LAMELLAR METAL BILLETS

    Directory of Open Access Journals (Sweden)

    V. V. Klubovich

    2011-01-01

    Full Text Available The results of experimental research of optimal modes of Plastic Forming coaxial layered metal blanks of the helical rolling of mill with a triple roll at the ends of pressurization of the package. Shown that the frontal surfaces of back pressure ensures the rational use of the base layer bimetal and improving the quality of the connection layer blanks at the expense of creating the conditions to the accumulation of compression strain in the weld zone. 

  20. Plasma gun with coaxial powder feed and adjustable cathode

    Science.gov (United States)

    Zaplatynsky, Isidor (Inventor)

    1991-01-01

    An improved plasma gun coaxially injects particles of ceramic materials having high melting temperatures into the central portion of a plasma jet. This results in a more uniform and higher temperature and velocity distribution of the sprayed particles. The position of the cathode is adjustable to facilitate optimization of the performance of the gun wherein grains of the ceramic material are melted at lower power input levels.

  1. Particle-like structure of coaxial Lie algebras

    Science.gov (United States)

    Vinogradov, A. M.

    2018-01-01

    This paper is a natural continuation of Vinogradov [J. Math. Phys. 58, 071703 (2017)] where we proved that any Lie algebra over an algebraically closed field or over R can be assembled in a number of steps from two elementary constituents, called dyons and triadons. Here we consider the problems of the construction and classification of those Lie algebras which can be assembled in one step from base dyons and triadons, called coaxial Lie algebras. The base dyons and triadons are Lie algebra structures that have only one non-trivial structure constant in a given basis, while coaxial Lie algebras are linear combinations of pairwise compatible base dyons and triadons. We describe the maximal families of pairwise compatible base dyons and triadons called clusters, and, as a consequence, we give a complete description of the coaxial Lie algebras. The remarkable fact is that dyons and triadons in clusters are self-organised in structural groups which are surrounded by casings and linked by connectives. We discuss generalisations and applications to the theory of deformations of Lie algebras.

  2. Fabrication and Characterisation of Flexible Coaxial Thin Thread Supercapacitors

    Directory of Open Access Journals (Sweden)

    Fulian Qiu

    2014-08-01

    Full Text Available Flexible coaxial thin thread supercapacitors were fabricated semi-automatically using a dip coating method. A typical coaxial thin thread supercapacitor of a length of 70 cm demonstrated a specific length capacitance of 0.3 mF cm-1 (11.2 mF cm-2 and 2.18 F cm-3 at 5 mV s-1, the device exhibited good electrochemical performance with a high volume energy density of 0.22 mWh cm-3 at a power density of 22 mW cm-3. Thread supercapacitors were assembled in series and parallel combinations, the accepted models for series and parallel circuit combinations were obeyed for two coaxial thread supercapacitors. The thread shows high flexibility and uniformity of specific length capacitance, one integrated with a commercial solar cell could be charged and power a LED. The process is simple, robust and easy to scale up to make unlimited length thread supercapacitors for numerous miniaturized and flexible electronic applications.

  3. Encapsulating darunavir nanocrystals within Eudragit L100 using coaxial electrospraying.

    Science.gov (United States)

    Nguyen, Duong Nhat; Clasen, Christian; Van den Mooter, Guy

    2017-04-01

    Electrospraying is renowned for its simplicity and versatility, and which can effectively produce particles with well-controlled size, size distribution, particle shape, morphology and microstructure at the nano/microscale. In this study, coaxial electrospraying was used to investigate its feasibility for preparing nanoparticles made up of nanocrystals encapsulated within a polymer shell. Firstly, aqueous nanosuspensions of darunavir were prepared by wet media milling. Then the nanosuspension and solutions of an enteric polymer, Eudragit L100, were used as the inner/core liquid and outer/shell liquid in a coaxial electrospraying setup, respectively. As long as a sufficiently high voltage was applied, a stable Taylor cone-jet mode was obtained to produce very fine core-shell structure nanoparticles with high darunavir encapsulation efficiency of approximately 90%. The influence of the starting nanosuspension and the flow rates on the characteristics of the final electrosprayed particles was also evaluated. Using an optimized nanosuspension with reasonable size, size distribution and flow rates, the enteric coating layer reduced the percentage of DRV release in acidic medium in the in vitro dissolution test to ca. 20%. This study indicates that coaxial electrospraying is a potential and unique technique for encapsulating drug nanocrystals within a polymeric shell. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Characteristics of Solution Plasma Generated with Coaxial DBD

    Science.gov (United States)

    Nishimoto, Kentaro; Tanaka, Kenji; Shirafuji, Tatsuru; Imai, Shin-Ichi

    2015-09-01

    Recently, solution plasma processing, or plasma processing in or in contact with an aqueous solution, has attracted much attention because of its various possible applications. Although different types of plasma generation methods have been proposed, most of them do not cover a wide range of electrical conductivity of the water to be treated. Since the water subjected to the plasma treatment can have any values of electrical conductivity depending on the purposes of treatments, we must develop methods that cover a wide range of electrical conductivity of water. The conventional solution plasma has shown a strong dependence on the electrical conductivity of water, in which stable discharge is available only in the water with an electrical conductivity of 100 +/- 50 μS/cm. The coaxial-type DBD in contrast has shown intense discharge within the conductivity range of 0.5-160 μS/cm. This result indicates that the coaxial type DBD has more ``robust'' dependence on the electrical conductivity of water. Furthermore, the coaxial type DBD has shown 3-fold higher energy efficiency in indigo carmine degradation than the conventional solution plasma.

  5. Silicon-Carbon Nanotube Coaxial Sponge as Li-Ion Anodes with High Areal Capacity

    KAUST Repository

    Hu, Liangbing

    2011-07-01

    Highly porous, conductive Si-CNT sponge-like structures with a large areal mass loading are demonstrated as effective Li-ion battery anode materials. Nano-pore formation and growth in the Si shell has been identified as the primary failure mode of the Si-CNT sponge anode, and the formation of such nanopores can be minimized by tuning the cutoff voltages. In conjunction with experiments, a theoretical analysis was carried out to explain the pore formation mechanism. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Silicon-carbon nanotube coaxial sponge as Li-ion anodes with high areal capacity

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Liangbing; Wu, Hui; McDough, James; Xie, Xing; Cui, Yi [Department of Materials Science and Engineering, Stanford University, Stanford, California, 94305 (United States); Gao, Yifan; Zhou, Min [The George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0405 (United States); Cao, Anyuan; Li, Hongbian [Department of Advanced Materials and Nanotechnology, College of Engineering, Peking University, Beijing 100871 (China)

    2011-07-15

    Highly porous, conductive Si-CNT sponge-like structures with a large areal mass loading are demonstrated as effective Li-ion battery anode materials. Nanopore formation and growth in the Si shell has been identified as the primary failure mode of the Si-CNT sponge anode, and the formation of such nanopores can be minimized by tuning the cutoff voltages. In conjunction with experiments, a theoretical analysis was carried out to explain the pore formation mechanism. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  7. Carbon nanotube quantum dots

    NARCIS (Netherlands)

    Sapmaz, S.

    2006-01-01

    Low temperature electron transport measurements on individual single wall carbon nanotubes are described in this thesis. Carbon nanotubes are small hollow cylinders made entirely out of carbon atoms. At low temperatures (below ~10 K) finite length nanotubes form quantum dots. Because of its small

  8. Numerical and experimental design of coaxial shallow geothermal energy systems

    Science.gov (United States)

    Raghavan, Niranjan

    Geothermal Energy has emerged as one of the front runners in the energy race because of its performance efficiency, abundance and production competitiveness. Today, geothermal energy is used in many regions of the world as a sustainable solution for decreasing dependence on fossil fuels and reducing health hazards. However, projects related to geothermal energy have not received their deserved recognition due to lack of computational tools associated with them and economic misconceptions related to their installation and functioning. This research focuses on numerical and experimental system design analysis of vertical shallow geothermal energy systems. The driving force is the temperature difference between a finite depth beneath the earth and its surface stimulates continuous exchange of thermal energy from sub-surface to the surface (a geothermal gradient is set up). This heat gradient is captured by the circulating refrigerant and thus, tapping the geothermal energy from shallow depths. Traditionally, U-bend systems, which consist of two one-inch pipes with a U-bend connector at the bottom, have been widely used in geothermal applications. Alternative systems include coaxial pipes (pipe-in-pipe) that are the main focus of this research. It has been studied that coaxial pipes have significantly higher thermal performance characteristics than U-bend pipes, with comparative production and installation costs. This makes them a viable design upgrade to the traditional piping systems. Analytical and numerical heat transfer analysis of the coaxial system is carried out with the help of ABAQUS software. It is tested by varying independent parameters such as materials, soil conditions and effect of thermal contact conductance on heat transfer characteristics. With the above information, this research aims at formulating a preliminary theoretical design setup for an experimental study to quantify and compare the heat transfer characteristics of U-bend and coaxial

  9. A novel ammonia complex-assisted ion-exchange strategy to fabricate heterostructured PdO/TiO2 nanorods with enhanced photocatalytic activities

    Science.gov (United States)

    Shi, Liang; Han, Qian; Cao, Lixin; Zhao, Fenghuan; Xia, Chenghui; Dong, Bohua; Xi, Yaoning

    2016-12-01

    Heterojunctions have been often employed to improve the photocatalytic behavior of titania-based materials. Herein, we propose a novel strategy to fabricate PdO/TiO2 heterostructured nanorods, as PdO was proved to be an efficient co-catalyst in photocatalytic reactions. Primarily, ammonia complex-assisted ion-exchange method was used to store Pd(II) ions in protonated titanate nanotubes, as which cannot be replaced by metallic cations via traditional route. Then, PdO/TiO2 heterojunctions formed through calcination in air, as nanotubes dehydrated and shrank into nanorods. X-ray diffraction, Raman spectra, and X-ray photoelectron spectroscopy were used to demonstrate the formation of PdO component, and transmission electron microscopy was employed to prove the successful connection between TiO2 nanorods and PdO nanoparticles. Moreover, inductive coupled plasma proved excellent compositional gradient of Pd(II) in the PdO/TiO2 heterostructured nanorods. In the present work, the photocatalytic activities of PdO/TiO2 heterostructured nanorods were investigated by decoloring several dyes under UV illumination. Our research revealed appropriate PdO loading (1.0 wt%) enhanced photocatalytic performance compared with bare TiO2 nanorods, where PdO/TiO2 heterojunctions were responsible for the prohibitive photogenerated carries recombination.

  10. High frequency nanotube oscillator

    Science.gov (United States)

    Peng, Haibing [Houston, TX; Zettl, Alexander K [Kensington, TX

    2012-02-21

    A tunable nanostructure such as a nanotube is used to make an electromechanical oscillator. The mechanically oscillating nanotube can be provided with inertial clamps in the form of metal beads. The metal beads serve to clamp the nanotube so that the fundamental resonance frequency is in the microwave range, i.e., greater than at least 1 GHz, and up to 4 GHz and beyond. An electric current can be run through the nanotube to cause the metal beads to move along the nanotube and changing the length of the intervening nanotube segments. The oscillator can operate at ambient temperature and in air without significant loss of resonance quality. The nanotube is can be fabricated in a semiconductor style process and the device can be provided with source, drain, and gate electrodes, which may be connected to appropriate circuitry for driving and measuring the oscillation. Novel driving and measuring circuits are also disclosed.

  11. Hot carrier-enhanced interlayer electron-hole pair multiplication in 2D semiconductor heterostructure photocells

    Science.gov (United States)

    Barati, Fatemeh; Grossnickle, Max; Su, Shanshan; Lake, Roger K.; Aji, Vivek; Gabor, Nathaniel M.

    2017-12-01

    Strong electronic interactions can result in novel particle-antiparticle (electron-hole, e-h) pair generation effects, which may be exploited to enhance the photoresponse of nanoscale optoelectronic devices. Highly efficient e-h pair multiplication has been demonstrated in several important nanoscale systems, including nanocrystal quantum dots, carbon nanotubes and graphene. The small Fermi velocity and nonlocal nature of the effective dielectric screening in ultrathin layers of transition-metal dichalcogenides (TMDs) indicates that e-h interactions are very strong, so high-efficiency generation of e-h pairs from hot electrons is expected. However, such e-h pair multiplication has not been observed in 2D TMD devices. Here, we report the highly efficient multiplication of interlayer e-h pairs in 2D semiconductor heterostructure photocells. Electronic transport measurements of the interlayer I-VSD characteristics indicate that layer-indirect e-h pairs are generated by hot-electron impact excitation at temperatures near T = 300 K. By exploiting this highly efficient interlayer e-h pair multiplication process, we demonstrate near-infrared optoelectronic devices that exhibit 350% enhancement of the optoelectronic responsivity at microwatt power levels. Our findings, which demonstrate efficient carrier multiplication in TMD-based optoelectronic devices, make 2D semiconductor heterostructures viable for a new class of ultra-efficient photodetectors based on layer-indirect e-h excitations.

  12. Hot carrier-enhanced interlayer electron-hole pair multiplication in 2D semiconductor heterostructure photocells.

    Science.gov (United States)

    Barati, Fatemeh; Grossnickle, Max; Su, Shanshan; Lake, Roger K; Aji, Vivek; Gabor, Nathaniel M

    2017-12-01

    Strong electronic interactions can result in novel particle-antiparticle (electron-hole, e-h) pair generation effects, which may be exploited to enhance the photoresponse of nanoscale optoelectronic devices. Highly efficient e-h pair multiplication has been demonstrated in several important nanoscale systems, including nanocrystal quantum dots, carbon nanotubes and graphene. The small Fermi velocity and nonlocal nature of the effective dielectric screening in ultrathin layers of transition-metal dichalcogenides (TMDs) indicates that e-h interactions are very strong, so high-efficiency generation of e-h pairs from hot electrons is expected. However, such e-h pair multiplication has not been observed in 2D TMD devices. Here, we report the highly efficient multiplication of interlayer e-h pairs in 2D semiconductor heterostructure photocells. Electronic transport measurements of the interlayer I-V SD characteristics indicate that layer-indirect e-h pairs are generated by hot-electron impact excitation at temperatures near T = 300 K. By exploiting this highly efficient interlayer e-h pair multiplication process, we demonstrate near-infrared optoelectronic devices that exhibit 350% enhancement of the optoelectronic responsivity at microwatt power levels. Our findings, which demonstrate efficient carrier multiplication in TMD-based optoelectronic devices, make 2D semiconductor heterostructures viable for a new class of ultra-efficient photodetectors based on layer-indirect e-h excitations.

  13. MoS2-Based Mixed-Dimensional van der Waals Heterostructures: A New Platform for Excellent and Controllable Microwave-Absorption Performance.

    Science.gov (United States)

    Sun, Yuan; Zhong, Wei; Wang, Yuanqi; Xu, Xiaobing; Wang, Tingting; Wu, Liqian; Du, Youwei

    2017-10-04

    It is widely recognized that constructing multiple interface structures for enhanced interface polarization is beneficial to microwave absorption. Here, we report our work of achieving excellent microwave-absorption performance and controlling better-defined interfaces in vertically stacked two-dimensional (2D) MoS 2 with other dimensional building blocks. The optimal reflection loss and effective absorbing bandwidth (reflection loss van der Waals heterostructures are as follows: (i) for 2-0 type (2D MoS 2 /zero-dimensional Ni nanoparticles), -19.7 dB and 2.92 GHz; (ii) for 2-1 type (2D MoS 2 /one-dimensional carbon nanotubes), -47.9 dB and 5.60 GHz; and (iii) for 2-3 type (2D MoS 2 /three-dimensional carbon layers), -69.2 dB and 4.88 GHz. As a result, by selected synthesis of different types of microstructures, we can regulate and control microwave-absorption properties in MoS 2 mixed-dimensional van der Waals heterostructures. In addition, attributing to the better-defined interfaces generated in mixed-dimensional van der Waals heterostructures, we found an alternative strategy to improve microwave attenuation properties of 2-0, 2-1, and 2-3 samples by controlling interfacial contacts. The results indicate that mixed-dimensional van der Waals heterostructures provide a new stage for the next generation of microwave-absorbing materials.

  14. The correlation between radiative surface defect states and high color rendering index from ZnO nanotubes

    Directory of Open Access Journals (Sweden)

    Ding Yong

    2011-01-01

    Full Text Available Abstract Combined surface, structural and opto-electrical investigations are drawn from the chemically fashioned ZnO nanotubes and its heterostructure with p-GaN film. A strong correlation has been found between the formation of radiative surface defect states in the nanotubes and the pure cool white light possessing averaged eight color rendering index value of 96 with appropriate color temperature. Highly important deep-red color index value has been realized > 95 which has the capability to render and reproduce natural and vivid colors accurately. Diverse types of deep defect states and their relative contribution to the corresponding wavelengths in the broad emission band is suggested.

  15. Heterostructures based on inorganic and organic van der Waals systems

    Directory of Open Access Journals (Sweden)

    Gwan-Hyoung Lee

    2014-09-01

    Full Text Available The two-dimensional limit of layered materials has recently been realized through the use of van der Waals (vdW heterostructures composed of weakly interacting layers. In this paper, we describe two different classes of vdW heterostructures: inorganic vdW heterostructures prepared by co-lamination and restacking; and organic-inorganic hetero-epitaxy created by physical vapor deposition of organic molecule crystals on an inorganic vdW substrate. Both types of heterostructures exhibit atomically clean vdW interfaces. Employing such vdW heterostructures, we have demonstrated various novel devices, including graphene/hexagonal boron nitride (hBN and MoS2 heterostructures for memory devices; graphene/MoS2/WSe2/graphene vertical p-n junctions for photovoltaic devices, and organic crystals on hBN with graphene electrodes for high-performance transistors.

  16. Analysis of Critical Dimensions for Nanowire Core-Multishell Heterostructures

    OpenAIRE

    Yan, Xin; Fan, Shuyu; Zhang, Xia; Ren, Xiaomin

    2015-01-01

    Critical dimensions for nanowire core-multishell heterostructures are analyzed by using finite-element method based on the energy equilibrium criteria. Results show that the nanowire core-shell heterostructure can sufficiently reduce the strain in the shell and increase the critical shell thickness. The critical dimensions for the nanowire core-multishell heterostructure are determined by the stress fields generated at two heterointerfaces. For thin barrier, the critical dimensions decrease a...

  17. A review of nano-optics in metamaterial hybrid heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Mahi R. [Department of Physics and Astronomy, Western University, London N6G 3K7 (Canada)

    2014-03-31

    We present a review for the nonlinear nano-optics in quantum dots doped in a metamaterial heterostructure. The heterostructure is formed by depositing a metamaterial on a dielectric substrate and ensemble of noninteracting quantum dots are doped near the heterostructure interface. It is shown that there is enhancement of the second harmonic generation due to the surface plasmon polaritons field present at the interface.

  18. Coaxial visible and FIR camera system with accurate geometric calibration

    Science.gov (United States)

    Ogino, Yuka; Shibata, Takashi; Tanaka, Masayuki; Okutomi, Masatoshi

    2017-05-01

    A far-infrared (FIR) image contains important invisible information for various applications such as night vision and fire detection, while a visible image includes colors and textures in a scene. We present a coaxial visible and FIR camera system accompanied to obtain the complementary information of both images simultaneously. The proposed camera system is composed of three parts: a visible camera, a FIR camera, and a beam-splitter made from silicon. The FIR radiation from the scene is reflected at the beam-splitter, while the visible radiation is transmitted through this beam-splitter. Even if we use this coaxial visible and FIR camera system, the alignment between the visible and FIR images are not perfect. Therefore, we also present the joint calibration method which can simultaneously estimate accurate geometric parameters of both cameras, i.e. the intrinsic parameters of both cameras and the extrinsic parameters between both cameras. In the proposed calibration method, we use a novel calibration target which has a two-layer structure where thermal emission property of each layer is different. By using the proposed calibration target, we can stably and precisely obtain the corresponding points of the checker pattern in the calibration target from both the visible and the FIR images. Widely used calibration tools can accurately estimate both camera parameters. We can obtain aligned visible and FIR images by the coaxial camera system with precise calibration using two-layer calibration target. Experimental results demonstrate that the proposed camera system is useful for various applications such as image fusion, image denoising, and image up-sampling.

  19. Modeling and simulation of coaxial helicopter rotor aerodynamics

    Science.gov (United States)

    Gecgel, Murat

    A framework is developed for the computational fluid dynamics (CFD) analyses of a series of helicopter rotor flowfields in hover and in forward flight. The methodology is based on the unsteady solutions of the three-dimensional, compressible Navier-Stokes equations recast in a rotating frame of reference. The simulations are carried out by solving the developed mathematical model on hybrid meshes that aim to optimally exploit the benefits of both the structured and the unstructured grids around complex configurations. The computer code is prepared for parallel processing with distributed memory utilization in order to significantly reduce the computational time and the memory requirements. The developed model and the simulation methodology are validated for single-rotor-in-hover flowfields by comparing the present results with the published experimental data. The predictive merit of different turbulence models for complex helicopter aerodynamics are tested extensively. All but the kappa-o and LES results demonstrate acceptable agreement with the experimental data. It was deemed best to use the one-equation Spalart-Allmaras turbulence model for the subsequent rotor flowfield computations. First, the flowfield around a single rotor in forward flight is simulated. These time---accurate computations help to analyze an adverse effect of increasing the forward flight speed. A dissymmetry of the lift on the advancing and the retreating blades is observed for six different advance ratios. Since the coaxial rotor is proposed to mitigate the dissymmetry, it is selected as the next logical step of the present investigation. The time---accurate simulations are successfully obtained for the flowfields generated by first a hovering then a forward-flying coaxial rotor. The results for the coaxial rotor in forward flight verify the aerodynamic balance proposed by the previously published advancing blade concept. The final set of analyses aims to investigate if the gap between the

  20. Coaxial ring cyclotron as a perspective nuclear power engineering machine

    CERN Document Server

    Tumanyan, A R; Mkrtchyan, R L; Amatuni, T A; Avakian, R O; Khudaverdian, A G

    1995-01-01

    Coaxial Ring Cyclotron (CRC) is described, and its main advantages, such as simple injection technique, several injected beams summation option, high efficiency, are considered. The proposed proton accelerator is a perspective machine for the solution of the main problems of the present day nuclear power engineering as well as for the next-generation nuclear power plants, representing a combination of subcritical reactors and particle accelerators. The possibility of installation of CRCs into ring accelerators with an average diameter from 60 to 100m, e.g., the Yerevan electron synchrotron, is considered.

  1. Coaxial Filters Optimization Using Tuning Space Mapping in CST Studio

    Directory of Open Access Journals (Sweden)

    D. Wolansky

    2011-04-01

    Full Text Available This paper deals with the optimization of coaxial filters using Tuning Space Mapping (TSM method implemented to CST environment. The function of fine and coarse model and their link between each other is explained. In addition, supporting macros programmed in VBA language, which are used for maximum efficiency of the optimization from the user´s point of view, are mentioned. Macros are programmed in CST and are also used for automatic calibration constants determination and for automatic calibration process between the coarse model and the fine model. The whole algorithm is illustrated on the particular seven-order filter design and optimized results are compared to measured ones.

  2. Theory and Circuit Model for Lossy Coaxial Transmission Line

    Energy Technology Data Exchange (ETDEWEB)

    Genoni, T. C.; Anderson, C. N.; Clark, R. E.; Gansz-Torres, J.; Rose, D. V.; Welch, Dale Robert

    2017-04-01

    The theory of signal propagation in lossy coaxial transmission lines is revisited and new approximate analytic formulas for the line impedance and attenuation are derived. The accuracy of these formulas from DC to 100 GHz is demonstrated by comparison to numerical solutions of the exact field equations. Based on this analysis, a new circuit model is described which accurately reproduces the line response over the entire frequency range. Circuit model calculations are in excellent agreement with the numerical and analytic results, and with finite-difference-time-domain simulations which resolve the skindepths of the conducting walls.

  3. Plasma-filled diode based on the coaxial gun

    Science.gov (United States)

    Zherlitsyn, A. A.; Kovalchuk, B. M.; Pedin, N. N.

    2012-10-01

    The paper presents the results of studies of a coaxial gun for a plasma-filled electron diode. Effects of the discharge channel diameter and gun current on characteristics of the plasma and pulse generated in the diode were investigated. The electron beam with maximum energy of ≥1 MeV at the current of ≈100 kA was obtained in the experiments with a plasma-filled diode. The energy of ≈5 kJ with the peak power of ≥100 GW dissipated in the diode.

  4. Vapor-solid growth of p-Te/n-SnO2 hierarchical heterostructures and their enhanced room-temperature gas sensing properties.

    Science.gov (United States)

    Her, Yung-Chiun; Yeh, Bu-Yu; Huang, Sing-Lin

    2014-06-25

    We have synthesized brushlike p-Te/n-SnO2 hierarchical heterostructures by a two-step thermal vapor transport process. The morphologies of the branched Te nanostructures can be manipulated by adjusting the source temperature or the argon flow rate. The growth of the branched Te nanotubes on the SnO2 nanowire backbones can be ascribed to the vapor-solid (VS) growth mechanism, in which the inherent anisotropic nature of Te lattice and/or dislocations lying along the Te nanotubes axis should play critical roles. When exposed to CO and NO2 gases at room temperature, Te/SnO2 hierarchical heterostructures changed the resistance in the same trend and exhibited much higher responses and faster response speeds than the Te nanotube counterparts. The enhancement in gas sensing performance can be ascribed to the higher specific surface areas and formations of numerous Te/Te or TeO2/TeO2 bridging point contacts and additional p-Te/n-SnO2 heterojunctions.

  5. On-line fingerprinting of fluids using coaxial stub resonator technology

    NARCIS (Netherlands)

    Hoog-Antonyuk, N.A.; Olthuis, Wouter; Mayer, M.J.J.; Yntema, D.; Miedema, H.; van den Berg, Albert

    2012-01-01

    Here we demonstrate the proof-of-principle of a coaxial stub resonator to assess the dielectric properties of fluids. This radio-frequency spectroscopy method is based on coaxial stub technology and comprises quarter wave length open-ended resonators that are filled with a liquid sample as

  6. Droplet Combustion and Non-Reactive Shear-Coaxial Jets with and without Transverse Acoustic Excitation

    Science.gov (United States)

    2012-01-01

    Journal, 28(8):1405–1414, 1990. [39] M. Favre-Marinet, E.B. Camano , and J. Sarboch. Near-field of coaxial jets with large density differences...Experiments in Fluids, 26(1):97–106, 1999. [40] M. Favre-Marinet and E.B. Camano Schettini. The density field of coaxial jets with large velocity ratio and

  7. Droplet Combustion and Non-Reactive Shear-Coaxial Jets with Transverse Acoustic Excitation

    Science.gov (United States)

    2012-06-01

    40] M. Favre-Marinet, E.B. Camano , and J. Sarboch. Near-field of coaxial jets with large density differences. Experiments in Fluids, 26(1):97–106, 1999...41] M. Favre-Marinet and E.B. Camano Schettini. The density field of coaxial jets with large velocity ratio and large density differences

  8. Methods for the algorithms for calculation of tunable coaxial bandpass microwave filters

    Directory of Open Access Journals (Sweden)

    Parfilov A. A.

    2012-12-01

    Full Text Available The article describes the features of the models and algorithms used for calculation of the characteristics of mechanically tunable coaxial bandpass microwave filters, on the basis of which a calculation computer program can be written. The ways are proposed to resolve ambiguities that arise in the course of development of the analytical algorithm for calculating coaxial tunable bandpass filters.

  9. Full-wave CAD of a rectangular waveguide filter with integrated coaxial excitation

    NARCIS (Netherlands)

    Gerini, G.; Guglielmi, M.

    2001-01-01

    Coaxial waveguides are very commonly used in many microwave subsystems for the connection of various components. Significant size reduction could, therefore, be achieved by integrating the design of the coaxial transition in the computer-aided design (CAD) of microwave filters. In this context, we

  10. Electrospun Flexible Coaxial Nanoribbons Endowed With Tuned and Simultaneous Fluorescent Color-Electricity-Magnetism Trifunctionality.

    Science.gov (United States)

    Shao, Hong; Ma, Qianli; Dong, Xiangting; Yu, Wensheng; Yang, Ming; Yang, Ying; Wang, Jinxian; Liu, Guixia

    2015-09-16

    In order to develop new-typed multifunctional nanocomposites, fluorescent-electrical-magnetic trifunctional coaxial nanoribbons with tunable fluorescent color, including white-light emission, have been successfully fabricated via coaxial electrospinning technology. Each stripe of coaxial nanoribbon is composed of a Fe3O4/PMMA core and a [Eu(BA)3phen+Dy(BA)3phen]/PANI/PMMA (PMMA = polymethyl methacrylate, BA = benzoic acid, phen = phenanthroline, polyaniline = PANI) shell. X-ray diffractometry (XRD), field emission scanning electron microscopy (FE-SEM), biological microscopy (BM), vibrating sample magnetometry (VSM), energy dispersive spectrometry (EDS), Hall effect measurement system and photoluminescence (PL) spectroscopy were employed to characterize the coaxial nanoribbons. Emitting color of the coaxial nanoribbons can be tuned by adjusting the contents of Dy(BA)3phen, Eu(BA)3phen, PANI and Fe3O4 in a wide color range of blue-white-orange under the excitation of 273-nm single-wavelength ultraviolet light. The coaxial nanoribbons simultaneously possess excellent luminescent performance, electrical conduction and magnetism compared with the counterpart composite nanoribbons. Furthermore, the electrical and magnetic performances of the coaxial nanoribbons also can be tunable by adding different quantities of PANI and Fe3O4 nanoparticles, respectively. The obtained coaxial nanoribbons have promising applications in many areas, such as electromagnetic interference shielding, microwave absorption, molecular electronics, biomedicine, future nanomechanics and display fields.

  11. Optimal Aerodynamic Design of Conventional and Coaxial Helicopter Rotors in Hover and Forward Flight

    Science.gov (United States)

    2015-12-28

    SECURITY CLASSIFICATION OF: This dissertation investigates the optimal aerodynamic performance and design of conventional and coaxial helicopters...Approved for public release; distribution is unlimited. Optimal Aerodynamic Design of Conventional andCoaxial Helicopter Rotors in Hover and ForwardFlight...Research Office P.O. Box 12211 Research Triangle Park, NC 27709-2211 rotor aerodynamics , optimal aerodynamics , hover, compund helicopters REPORT

  12. Thermal response in van der Waals heterostructures

    KAUST Repository

    Gandi, Appala

    2016-11-21

    We solve numerically the Boltzmann transport equations of the phonons and electrons to understand the thermoelectric response in heterostructures of M2CO2 (M: Ti, Zr, Hf) MXenes with transition metal dichalcogenide monolayers. Low frequency optical phonons are found to occur as a consequence of the van der Waals bonding, contribute significantly to the thermal transport, and compensate for the reduced contributions of the acoustic phonons (increased scattering cross-sections in heterostructures), such that the thermal conductivities turn out to be similar to those of the bare MXenes. Our results indicate that the important superlattice design approach of thermoelectrics (to reduce the thermal conductivity) may be effective for two-dimensional van der Waals materials when used in conjunction with intercalation. © 2016 IOP Publishing Ltd.

  13. Phonon engineering in proximity enhanced superconductor heterostructures.

    Science.gov (United States)

    Tang, Yong-Chao; Kwon, Sangil; Mohebbi, Hamid R; Cory, David G; Miao, Guo-Xing

    2017-06-27

    In this research, we tailor the phonon density of states (DOS) in thin superconducting films to suppress quasiparticle losses. We examine a model system of a proximity-enhanced three-layered Al/Nb/Al heterostructure and show that the local quantized phonon spectrum of the ultrathin Al cladding layers in the heterostructure has a pronounced effect on the superconducting resonator's quality factors. Instead of a monotonic increase of quality factors with decreasing temperatures, we observe the quality factor reaches a maximum at 1.2 K in 5/50/5 nm Al/Nb/Al microstrip resonators, because of a quantized phonon ladder. The phonon DOS may be engineered to enhance the performance of quantum devices.

  14. Proximity coupling in superconductor-graphene heterostructures

    OpenAIRE

    Lee, Gil-Ho; Lee, Hu-Jong

    2017-01-01

    This review discusses the electronic properties and the prospective research directions of superconductor-graphene heterostructures. The basic electronic properties of graphene are introduced to highlight the unique possibility of combining two seemingly unrelated physics, superconductivity and relativity. We then focus on graphene-based Josephson junctions, one of the most versatile superconducting quantum devices. The various theoretical methods that have been developed to describe graphene...

  15. Voltage control of magnetism in multiferroic heterostructures.

    Science.gov (United States)

    Liu, Ming; Sun, Nian X

    2014-02-28

    Electrical tuning of magnetism is of great fundamental and technical importance for fast, compact and ultra-low power electronic devices. Multiferroics, simultaneously exhibiting ferroelectricity and ferromagnetism, have attracted much interest owing to the capability of controlling magnetism by an electric field through magnetoelectric (ME) coupling. In particular, strong strain-mediated ME interaction observed in layered multiferroic heterostructures makes it practically possible for realizing electrically reconfigurable microwave devices, ultra-low power electronics and magnetoelectric random access memories (MERAMs). In this review, we demonstrate this remarkable E-field manipulation of magnetism in various multiferroic composite systems, aiming at the creation of novel compact, lightweight, energy-efficient and tunable electronic and microwave devices. First of all, tunable microwave devices are demonstrated based on ferrite/ferroelectric and magnetic-metal/ferroelectric composites, showing giant ferromagnetic resonance (FMR) tunability with narrow FMR linewidth. Then, E-field manipulation of magnetoresistance in multiferroic anisotropic magnetoresistance and giant magnetoresistance devices for achieving low-power electronic devices is discussed. Finally, E-field control of exchange-bias and deterministic magnetization switching is demonstrated in exchange-coupled antiferromagnetic/ferromagnetic/ferroelectric multiferroic hetero-structures at room temperature, indicating an important step towards MERAMs. In addition, recent progress in electrically non-volatile tuning of magnetic states is also presented. These tunable multiferroic heterostructures and devices provide great opportunities for next-generation reconfigurable radio frequency/microwave communication systems and radars, spintronics, sensors and memories.

  16. Strain engineering of van der Waals heterostructures.

    Science.gov (United States)

    Vermeulen, Paul A; Mulder, Jefta; Momand, Jamo; Kooi, Bart J

    2018-01-18

    Modifying the strain state of solids allows control over a plethora of functional properties. The weak interlayer bonding in van der Waals (vdWaals) materials such as graphene, hBN, MoS2, and Bi2Te3 might seem to exclude strain engineering, since strain would immediately relax at the vdWaals interfaces. Here we present direct observations of the contrary by showing growth of vdWaals heterostructures with persistent in-plane strains up to 5% and we show that strain relaxation follows a not yet reported process distinctly different from strain relaxation in three-dimensionally bonded (3D) materials. For this, 2D bonded Bi2Te3-Sb2Te3 and 2D/3D bonded Bi2Te3-GeTe multilayered films are grown using Pulsed Laser Deposition (PLD) and their structure is monitored in situ using Reflective High Energy Electron Diffraction (RHEED) and post situ analysis is performed using Transmission Electron Microscopy (TEM). Strain relaxation is modeled and found to solely depend on the layer being grown and its initial strain. This insight demonstrates that strain engineering of 2D bonded heterostructures obeys different rules than hold for epitaxial 3D materials and opens the door to precise tuning of the strain state of the individual layers to optimize functional performance of vdWaals heterostructures.

  17. Carbon nanotubes decorating methods

    OpenAIRE

    A.D. Dobrzańska-Danikiewicz; Łukowiec, D.; D. Cichock; W. Wolany

    2013-01-01

    Purpose: The work is to present and characterise various methods of depositing carbon nanotubes with nanoparticles of precious metals, and also to present the results of own works concerning carbon nanotubes coated with platinum nanoparticles.Design/methodology/approach: Electron transmission and scanning microscopy has been used for imaging the structure and morphology of the nanocomposites obtained and the distribution of nanoparticles on the surface of carbon nanotubes.Findings: The studie...

  18. Coaxial flow-gating interface for capillary electrophoresis.

    Science.gov (United States)

    Opekar, František; Tůma, Petr

    2017-08-01

    A coaxial flow-gating interface is described in which the separation capillary passes through the sampling capillary. Continuous flow of the sample solution flowing out of the sampling capillary is directed away from the injection end of the separation capillary by counter-current flow of the gating solution. During the injection, the flow of the gating solution is interrupted, so that a plug of solution is formed at the inlet into the separation capillary, from which the sample is hydrodynamically injected. Flow-gating interfaces are originally designed for on-line connection of capillary electrophoresis with analytical flow-through methods. The basic properties of the described coaxial flow-gating interface were obtained in a simplified arrangement in which a syringe pump with sample solution has substituted analytical flow-through method. Under the optimized conditions, the properties of the tested interface were determined by separation of K + , Ba 2+ , Na + , Mg 2+ and Li + ions in aqueous solution at equimolar concentrations of 50 μM. The repeatability of the migration times and peak areas evaluated for K + , Ba 2+ and Li + ions and expressed as relative standard deviation did not exceed 1.4%. The interface was used to determine lithium in mineral water and taurine in an energy drink. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Tunable engineered skin mechanics via coaxial electrospun fiber core diameter.

    Science.gov (United States)

    Blackstone, Britani Nicole; Drexler, Jason William; Powell, Heather Megan

    2014-10-01

    Autologous engineered skin (ES) offers promise as a treatment for massive full thickness burns. Unfortunately, ES is orders of magnitude weaker than normal human skin causing it to be difficult to apply surgically and subject to damage by mechanical shear in the early phases of engraftment. In addition, no manufacturing strategy has been developed to tune ES biomechanics to approximate the native biomechanics at different anatomic locations. To enhance and tune ES biomechanics, a coaxial (CoA) electrospun scaffold platform was developed from polycaprolactone (PCL, core) and gelatin (shell). The ability of the coaxial fiber core diameter to control both scaffold and tissue mechanics was investigated along with the ability of the gelatin shell to facilitate cell adhesion and skin development compared to pure gelatin, pure PCL, and a gelatin-PCL blended fiber scaffold. CoA ES exhibited increased cellular adhesion and metabolism versus PCL alone or gelatin-PCL blend and promoted the development of well stratified skin with a dense dermal layer and a differentiated epidermal layer. Biomechanics of the scaffold and ES scaled linearly with core diameter suggesting that this scaffold platform could be utilized to tailor ES mechanics for their intended grafting site and reduce graft damage in vitro and in vivo.

  20. Geothermal heat exchanger with coaxial flow of fluids

    Directory of Open Access Journals (Sweden)

    Pejić Dragan M.

    2005-01-01

    Full Text Available The paper deals with a heat exchanger with coaxial flow. Two coaxial pipes of the secondary part were placed directly into a geothermal boring in such a way that geothermal water flows around the outer pipe. Starting from the energy balance of the exchanger formed in this way and the assumption of a study-state operating regime, a mathematical model was formulated. On the basis of the model, the secondary circle output temperature was determined as a function of the exchanger geometry, the coefficient of heat passing through the heat exchange areas, the average mass isobaric specific heats of fluid and mass flows. The input temperature of the exchanger secondary circle and the temperature of the geothermal water at the exit of the boring were taken as known values. Also, an analysis of changes in certain factors influencing the secondary water temperature was carried out. The parameters (flow temperature of the deep boring B-4 in Sijarinska Spa, Serbia were used. The theoretical results obtained indicate the great potential of this boring and the possible application of such an exchanger.

  1. A numerical study of non-isothermal turbulent coaxial jets

    Energy Technology Data Exchange (ETDEWEB)

    Kriaa, Wassim; Abderrazak, Kamel; Mhiri, Hatem [Ecole Nationale d' Ingenieurs de Monastir, Laboratoire de Mecanique des Fluides et Thermique, Monastir (Tunisia); Palec, Georges le; Bournot, Philippe [Institut de Mecanique de Marseille, Marseille (France)

    2008-07-15

    In this work, we propose to study non isothermal air-air coaxial jets with two different approaches: parabolic and elliptic approaches. The standard k-{epsilon} model and the RSM model were applied in this study. The numerical resolution of the equations governing this flow type was carried out for: the parabolic approach, by a ''home-made'' CFD code based on a finite difference method, and the elliptic approach by an industrial code (FLUENT) based on a finite volume method. In forced convection mode (Fr={infinity}), the two turbulence models are valid for the prediction of the mean flow. But for turbulent sizes, k-{epsilon} model gives results closer to those achieved in experiments compared to RSM Model. Concerning the limit of validity of the parabolic and elliptic approaches, we showed that for velocities ratio r lower than 1, the results of the two approaches were satisfactory. On the other hand, for r>1, the difference between the results became increasingly significant. In mixed convection mode (Fr{approx_equal}20), the results obtained by the two turbulence models for the mean axial velocity were very different even in the plume region. For the temperature and the turbulent sizes the two models give satisfactory results which agree well with the correlations suggested by the experimenters for X{>=}20. Thus, the second order model with {sigma}{sub t}=0.85 is more effective for a coaxial jet study in a mixed convection mode. (orig.)

  2. A large cooling capacity single stage coaxial pulse tube cooler

    Science.gov (United States)

    Poncet, J. M.; Trollier, T.; Ravex, A.

    2002-05-01

    CEA/SBT has a long experience in Pulse Tube Coolers (PTC) development. In the framework of the Brite Euram Program READY, for an HTS transformer demonstrator designed by Schneider Electric, a specific large cooling power single stage coaxial PTC has been designed, manufactured and successfully tested in partnership between CEA/SBT and Air Liquide. The performance requirement was 65 W between 50 K and 77 K. The prototype, associated with a 6 kW Gifford McMohan compression unit, has demonstrated the following performance: an ultimate temperature of 30 K, and typical heat lift of 40 W @40 K, 80 W @60 K and 100 W @80 K were achieved. This particular prototype featured a stainless-steel mesh regenerator: the introduction of lead shot would further increase the cooling capacity below 50 K. The original design and performance of this prototype are presented. A scaled down version of this coaxial PTC is currently under development for an HTS NMR probe cooling at 65 K (more than 20 W).

  3. A contoured gap coaxial plasma gun with injected plasma armature.

    Science.gov (United States)

    Witherspoon, F Douglas; Case, Andrew; Messer, Sarah J; Bomgardner, Richard; Phillips, Michael W; Brockington, Samuel; Elton, Raymond

    2009-08-01

    A new coaxial plasma gun is described. The long term objective is to accelerate 100-200 microg of plasma with density above 10(17) cm(-3) to greater than 200 km/s with a Mach number above 10. Such high velocity dense plasma jets have a number of potential fusion applications, including plasma refueling, magnetized target fusion, injection of angular momentum into centrifugally confined mirrors, high energy density plasmas, and others. The approach uses symmetric injection of high density plasma into a coaxial electromagnetic accelerator having an annular gap geometry tailored to prevent formation of the blow-by instability. The injected plasma is generated by numerous (currently 32) radially oriented capillary discharges arranged uniformly around the circumference of the angled annular injection region of the accelerator. Magnetohydrodynamic modeling identified electrode profiles that can achieve the desired plasma jet parameters. The experimental hardware is described along with initial experimental results in which approximately 200 microg has been accelerated to 100 km/s in a half-scale prototype gun. Initial observations of 64 merging injector jets in a planar cylindrical testing array are presented. Density and velocity are presently limited by available peak current and injection sources. Steps to increase both the drive current and the injected plasma mass are described for next generation experiments.

  4. Engineering design of the PLX- α coaxial gun

    Science.gov (United States)

    Cruz, E.; Brockington, S.; Case, A.; Luna, M.; Witherspoon, F. D.; Thio, Y. C. Francis; PLX-α Team

    2017-10-01

    We describe the engineering and technical improvements, as well as provide a detailed overview of the design choices, of the latest PLX- α coaxial gun designed for the 60-gun scaling study of spherically imploding plasma liners as a standoff driver for plasma-jet-driven magneto-inertial fusion. Each coaxial gun incorporates a fast, dense gas injection and triggering system, a compact low-weight pfn with integral sparkgap switching, and a contoured gap designed to suppress the blow-by instability. The evolution of the latest Alpha gun is presented with emphasis on its upgraded performance. Changes include a faster more robust gas valve, better-quality ceramic insulator material and enhancements to overall design layout. These changes result in a gun with increased repeatability, reduced potential failure modes, improved fault tolerance and better than expected efficiency. A custom 600- μF, 5-kV pfn and a set of six inline sparkgap switches operated in parallel are mounted directly to the back of the gun, and are designed to reduce inductance, cost, and complexity, maximize efficiency and system reliability, and ensure symmetric current flow. This work supported by the ARPA-E ALPHA Program under contract DE-AR0000566 and Strong Atomics, LLC.

  5. Numerical modeling of deflagration mode in coaxial plasma guns

    Science.gov (United States)

    Sitaraman, Hariswaran; Raja, Laxminarayan

    2012-10-01

    Pulsed coaxial plasma guns have been used in several applications in the field of space propulsion, nuclear fusion and materials processing. These devices operate in two modes based on the delay between gas injection and breakdown initiation. Larger delay led to the plasma detonation mode where a compression wave in the form of a luminous front propagates from the breech to the muzzle. Shorter delay led to the more efficient deflagration mode characterized by a relatively diffuse plasma with higher resistivity. The overall physics of the discharge in the two modes of operation and in particular the latter remain relatively unexplored. Here we perform a computational modeling study by solving the non-ideal Magneto-hydrodynamics equations for the quasi-neutral plasma in the coaxial plasma gun. A finite volume formulation on an unstructured mesh framework with an implicit scheme is used to do stable computations. The final work will present details of important species in the plasma, particle energies and Mach number at the muzzle. A comparison of the plasma parameters will be made with the experiments reported in ref. [1]. [4pt] [1] F. R. Poehlmann et al., Phys. Plasmas 17, 123508 (2010)

  6. Contoured-gap coaxial guns for imploding plasma liner experiments

    Science.gov (United States)

    Witherspoon, F. D.; Case, A.; Brockington, S.; Cassibry, J. T.; Hsu, S. C.

    2014-10-01

    Arrays of supersonic, high momentum flux plasma jets can be used as standoff compression drivers for generating spherically imploding plasma liners for driving magneto-inertial fusion, hence the name plasma-jet-driven MIF (PJMIF). HyperV developed linear plasma jets for the Plasma Liner Experiment (PLX) at LANL where two guns were successfully tested. Further development at HyperV resulted in achieving the PLX goal of 8000 μg at 50 km/s. Prior work on contoured-gap coaxial guns demonstrated an approach to control the blowby instability and achieved substantial performance improvements. For future plasma liner experiments we propose to use contoured-gap coaxial guns with small Minirailgun injectors. We will describe such a gun for a 60-gun plasma liner experiment. Discussion topics will include impurity control, plasma jet symmetry and topology (esp. related to uniformity and compactness), velocity capability, and techniques planned for achieving gun efficiency of >50% using tailored impedance matched pulse forming networks. Mach2 and UAH SPH code simulations will be included. Work supported by US DOE DE-FG02-05ER54810.

  7. Numerical Simulations of the Flame of a Single Coaxial Injector

    Directory of Open Access Journals (Sweden)

    Victor P. Zhukov

    2017-01-01

    Full Text Available The processes of mixing and combustion in the jet of a shear-coaxial injector are investigated. Two test cases (nonreacting and reacting are simulated using the commercial computational fluid dynamics code ANSYS CFX. The first test case is an experiment on the mixing in a nonreacting coaxial jet carried out with the use of planar laser induced fluorescence (PLIF. The second test case is an experiment on the visualization of hydrogen-oxygen flame using PLIF of OH in a single injector combustion chamber at pressure of 53 bar. In the first test case, the two-dimensional axisymmetric simulations are performed using the shear-stress turbulence (SST model. Due to the dominant flow unsteadiness in the second test case, the turbulence is modeled using transient SAS (Scale-Adaptive Simulation model. The combustion is modeled using the burning velocity model (BVM while both two- and three-dimensional simulations are carried out. The numerical model agrees with the experimental data very well in the first test case and adequately in the second test case.

  8. Numerical Simulation of Hydrogen Air Supersonic Coaxial Jet

    Science.gov (United States)

    Dharavath, Malsur; Manna, Pulinbehari; Chakraborty, Debasis

    2017-10-01

    In the present study, the turbulent structure of coaxial supersonic H2-air jet is explored numerically by solving three dimensional RANS equations along with two equation k-ɛ turbulence model. Grid independence of the solution is demonstrated by estimating the error distribution using Grid Convergence Index. Distributions of flow parameters in different planes are analyzed to explain the mixing and combustion characteristics of high speed coaxial jets. The flow field is seen mostly diffusive in nature and hydrogen diffusion is confined to core region of the jet. Both single step laminar finite rate chemistry and turbulent reacting calculation employing EDM combustion model are performed to find the effect of turbulence-chemistry interaction in the flow field. Laminar reaction predicts higher H2 mol fraction compared to turbulent reaction because of lower reaction rate caused by turbulence chemistry interaction. Profiles of major species and temperature match well with experimental data at different axial locations; although, the computed profiles show a narrower shape in the far field region. These results demonstrate that standard two equation class turbulence model with single step kinetics based turbulence chemistry interaction can describe H2-air reaction adequately in high speed flows.

  9. Purification of carbon nanotubes via selective heating

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, John A.; Wilson, William L.; Jin, Sung Hun; Dunham, Simon N.; Xie, Xu; Islam, Ahmad; Du, Frank; Huang, Yonggang; Song, Jizhou

    2017-11-21

    The present invention provides methods for purifying a layer of carbon nanotubes comprising providing a precursor layer of substantially aligned carbon nanotubes supported by a substrate, wherein the precursor layer comprises a mixture of first carbon nanotubes and second carbon nanotubes; selectively heating the first carbon nanotubes; and separating the first carbon nanotubes from the second carbon nanotubes, thereby generating a purified layer of carbon nanotubes. Devices benefiting from enhanced electrical properties enabled by the purified layer of carbon nanotubes are also described.

  10. Analysis of Coaxial Soil Cell in Reflection and Transmission

    Directory of Open Access Journals (Sweden)

    Robert J. Lascano

    2011-03-01

    Full Text Available Accurate measurement of moisture content is a prime requirement in hydrological, geophysical and biogeochemical research as well as for material characterization and process control. Within these areas, accurate measurements of the surface area and bound water content is becoming increasingly important for providing answers to many fundamental questions ranging from characterization of cotton fiber maturity, to accurate characterization of soil water content in soil water conservation research to bio-plant water utilization to chemical reactions and diffusions of ionic species across membranes in cells as well as in the dense suspensions that occur in surface films. In these bound water materials, the errors in the traditional time-domain-reflectometer, “TDR”, exceed the range of the full span of the material’s permittivity that is being measured. Thus, there is a critical need to re-examine the TDR system and identify where the errors are to direct future research. One promising technique to address the increasing demands for higher accuracy water content measurements is utilization of electrical permittivity characterization of materials. This technique has enjoyed a strong following in the soil-science and geological community through measurements of apparent permittivity via time-domain-reflectometery as well in many process control applications. Recent research however, is indicating a need to increase the accuracy beyond that available from traditional TDR. The most logical pathway then becomes a transition from TDR based measurements to network analyzer measurements of absolute permittivity that will remove the adverse effects that high surface area soils and conductivity impart onto the measurements of apparent permittivity in traditional TDR applications. This research examines the theoretical basis behind the coaxial probe, from which the modern TDR probe originated from, to provide a basis on which to perform absolute

  11. Carbon nanotubes cement composites

    OpenAIRE

    Simone Musso; Jean-Marc Tulliani; Giuseppe Ferro

    2011-01-01

    The present paper reviews the current state of the art of carbon nanotubes cement-based composites and the possible applications. The influence of carbon nanotubes additions onto cement paste mechanical and electrical properties are discussed in detail. Though promising, several challenges have still to be solved before the introduction of these new materials into the public sphere through civil infrastructures.

  12. Carbon nanotube macroelectronics

    Science.gov (United States)

    Zhang, Jialu

    In this dissertation, I discuss the application of carbon nanotubes in macroelectronis. Due to the extraordinary electrical properties such as high intrinsic carrier mobility and current-carrying capacity, single wall carbon nanotubes are very desirable for thin-film transistor (TFT) applications such as flat panel display, transparent electronics, as well as flexible and stretchable electronics. Compared with other popular channel material for TFTs, namely amorphous silicon, polycrystalline silicon and organic materials, nanotube thin-films have the advantages of low-temperature processing compatibility, transparency, and flexibility, as well as high device performance. In order to demonstrate scalable, practical carbon nanotube macroelectroncis, I have developed a platform to fabricate high-density, uniform separated nanotube based thin-film transistors. In addition, many other essential analysis as well as technology components, such as nanotube film density control, purity and diameter dependent semiconducting nanotube electrical performance study, air-stable n-type transistor fabrication, and CMOS integration platform have also been demonstrated. On the basis of the above achievement, I have further demonstrated various kinds of applications including AMOLED display electronics, PMOS and CMOS logic circuits, flexible and transparent electronics. The dissertation is structured as follows. First, chapter 1 gives a brief introduction to the electronic properties of carbon nanotubes, which serves as the background knowledge for the following chapters. In chapter 2, I will present our approach of fabricating wafer-scale uniform semiconducting carbon nanotube thin-film transistors and demonstrate their application in display electronics and logic circuits. Following that, more detailed information about carbon nanotube thin-film transistor based active matrix organic light-emitting diode (AMOLED) displays is discussed in chapter 3. And in chapter 4, a technology to

  13. A non-coaxial critical state soil model and its application to simple shear simulations

    Science.gov (United States)

    Yang, Yunming; Yu, H. S.

    2006-11-01

    The yield vertex non-coaxial theory is implemented into a critical state soil model, CASM (Int. J. Numer. Anal. Meth. Geomech. 1998; 22:621-653) to investigate the non-coaxial influences on the stress-strain simulations of real soil behaviour in the presence of principal stress rotations. The CASM is a unified clay and sand model, developed based on the soil critical state concept and the state parameter concept. Without loss of simplicity, it is capable of simulating the behaviour of sands and clays within a wide range of densities. The non-coaxial CASM is employed to simulate the simple shear responses of Erksak sand and Weald clay under different densities and initial stress states. Dependence of the soil behaviour on the Lode angle and different plastic flow rules in the deviatoric plane are also considered in the study of non-coaxial influences. All the predictions indicate that the use of the non-coaxial model makes the orientations of the principal stress and the principal strain rate different during the early stage of shearing, and they approach the same ultimate values with an increase in loading. These ultimate orientations are dependent on the density of soils, and independent of their initial stress states. The use of the non-coaxial model also softens the shear stress evolutions, compared with the coaxial model. It is also found that the ultimate shear strengths by using the coaxial and non-coaxial models are dependent on the plastic flow rules in the deviatoric plane. Copyright

  14. Topology Optimisation of Wideband Coaxial-to-Waveguide Transitions

    Science.gov (United States)

    Hassan, Emadeldeen; Noreland, Daniel; Wadbro, Eddie; Berggren, Martin

    2017-03-01

    To maximize the matching between a coaxial cable and rectangular waveguides, we present a computational topology optimisation approach that decides for each point in a given domain whether to hold a good conductor or a good dielectric. The conductivity is determined by a gradient-based optimisation method that relies on finite-difference time-domain solutions to the 3D Maxwell’s equations. Unlike previously reported results in the literature for this kind of problems, our design algorithm can efficiently handle tens of thousands of design variables that can allow novel conceptual waveguide designs. We demonstrate the effectiveness of the approach by presenting optimised transitions with reflection coefficients lower than -15 dB over more than a 60% bandwidth, both for right-angle and end-launcher configurations. The performance of the proposed transitions is cross-verified with a commercial software, and one design case is validated experimentally.

  15. Near-field of coaxial jets with large density differences

    Energy Technology Data Exchange (ETDEWEB)

    Favre-Marinet, M. [Institut de Mecanique de Grenoble, 38 (France); Camano, E.B. [Instituto de Pesquisas Hidraulicas Universidade Federal de Rio Grande do sul CP 15029, 91501-970 Porto Alegre (Brazil); Sarboch, J. [Department of Fluid Mechanics and Thermodynamics, Czech Technical University, Prague (Czech Republic)

    1999-01-01

    The paper describes an experimental investigation of coaxial jets with large density differences. Measurements by various techniques show that density effects on the flow dynamics are taken into account to first order by considering the specific outer to inner jet momentum flux ratio M and not separately the density and velocity ratios. A regime of recirculation occurs for M higher than a critical value (M{sub c}{approx}50). For a given value of M, however, the position of the recirculation bubble is slightly shifted in the upstream direction for density ratios much smaller than one. An unexpected result is obtained for an extremely low density ratio: the onset of recirculation occurs for a significantly higher value of M (100

  16. Chemical activation using an open-end coaxial applicator.

    Science.gov (United States)

    Longo, Iginio; Ricci, Andrea Simone

    2007-01-01

    This article gives an overview of a novel, experimentally simple and versatile method of activation of chemical processes with microwaves without resorting to an oven. It is based on the use of a microwave antenna, namely an open-end coaxial dipole applicator immersed in an ordinary reaction vessel. Accounts of the apparatus at 2450 MHz and of the procedures adopted in reactions of organic synthesis, extraction of essential oils from plants and photo catalytic mineralization of liquid pollutants are given, discussing the necessary safety measures. The method is of practical interest for scientific and industrial applications. Thus this article is meant for a broad audience of scientists, engineers and technicians interested in new technologies for chemistry.

  17. Propellant Feed System for Swirl-Coaxial Injection

    Science.gov (United States)

    Reynolds, David Christopher (Inventor)

    2015-01-01

    A propellant feed system for swirl-coaxial injection of a liquid propellant includes a reservoir having a bottom plate and at least one tube originating in the bottom plate and extending therefrom. The tube has rectangular slits defined in and distributed tangentially and evenly about a portion of the tube that is disposed in the bottom plate. Drain holes are provided in the bottom plate and tunnels are defined in the bottom plate. Each tunnel fluidly couples one of the drain holes to a corresponding one of the rectangular slits. Each tunnel includes (i) a bend of at least 90.degree., and (ii) a straight portion leading to its corresponding rectangular slit wherein the straight portion is at least five times as long as a hydraulic diameter of the corresponding rectangular slit.

  18. Modeling and analysis of water-hammer in coaxial pipes

    CERN Document Server

    Cesana, Pierluigi

    2015-01-01

    The fluid-structure interaction is studied for a system composed of two coaxial pipes in an annular geometry, for both homogeneous isotropic metal pipes and fiber-reinforced (anisotropic) pipes. Multiple waves, traveling at different speeds and amplitudes, result when a projectile impacts on the water filling the annular space between the pipes. In the case of carbon fiber-reinforced plastic thin pipes we compute the wavespeeds, the fluid pressure and mechanical strains as functions of the fiber winding angle. This generalizes the single-pipe analysis of J. H. You, and K. Inaba, Fluid-structure interaction in water-filled pipes of anisotropic composite materials, J. Fl. Str. 36 (2013). Comparison with a set of experimental measurements seems to validate our models and predictions.

  19. Multi-phase simulations of coaxial injector combustion

    Science.gov (United States)

    Liang, P. Y.; Ungewitter, R. J.

    1992-01-01

    A multiphase computational fluid dynamics code (ARICC-3D) is presented and results of two simulations are discussed. The numerical framework of the CFD code is reviewed as well as some of the two-phase physical submodels. The simulations performed include a single coaxial element injector and a multielement injector using LOX/Hydrogen reactants. The single element injector simulation verified the interaction among the code's submodels. The multielement injector simulation transient results include the chamber response to a transverse pressure wave with and without a chamber baffle. The results of these simulations demonstrate the current capabilities and their limitations to model complex two-phase combustion phenomena. Possible ways to exceed these limitations are suggested.

  20. Microfabrication of curcumin-loaded microparticles using coaxial electrohydrodynamic atomization

    Science.gov (United States)

    Yuan, Shuai; Si, Ting; Liu, Zhongfa; Xu, Ronald X.

    2014-03-01

    Encapsulation of curcumin in PLGA microparticles is performed by a coaxial electrohydrodynamic atomization device. To optimize the process, the effects of different control parameters on morphology and size distribution of resultant microparticles are studied systemically. Four main flow modes are identified as the applied electric field intensity increases. The stable cone-jet configuration is found to be available for fabricating monodisperse microparticles with core-shell structures. The results are compared with those observed in traditional emulsion. The drug-loading efficiency is also checked. The present system is advantageous for the enhancement of particle size distribution and drug-loading efficiency in various applications such as drug delivery, biomedicine and image-guided therapy.

  1. All-optical coaxial framing photography using parallel coherence shutters.

    Science.gov (United States)

    Guanghua, Chen; Jianfeng, Li; Qixian, Peng; Shouxian, Liu; Jun, Liu

    2017-02-01

    An all-optical framing camera has been developed to obtain serial images of high temporal and spatial resolution with identical spatial benchmark, identical temporal benchmark, and identical chromatic benchmark in a single shot. A train of laser probe pulses with identical wavelength coaxially illuminate the target and form sequentially timed images by means of parallel coherence shutters. A coherence shutter only selects one of the probe pulses to form a nonmultiplexing hologram. The other probe pulses superpose incoherently on the hologram as the background. By this method, each hologram is entirely separated from the others both in spatial and temporal domains. Two kinds of ultrafast physical process experiments, including laser driving air and laser driving aluminum foil, were performed to verify the feasibility of the parallel coherence shutters.

  2. Mixing and coherent vortices in turbulent coaxial jets

    Science.gov (United States)

    Balarac, Guillaume; Si-Ameur, Mohamed

    2005-08-01

    Direct numerical simulations associated with mixing in constant-density round coaxial jets are performed. They are validated by comparison against laboratory experiments. The mixing process is studied by seeding a passive tracer first in the outer annular jet, then in the inner jet. We demonstrate the important role played by coherent vortices in the mixing mechanisms. The turbulent mixing exhibits an intermittent character as a consequence of fluid ejections caused by the counter-rotating streamwise vortices. We quantify also the domination of the outer jet and show that the fluid issuing from the central jet remains confined. To cite this article: G. Balarac, M. Si-Ameur, C. R. Mecanique 333 (2005).

  3. Flow of fractional Maxwell fluid between coaxial cylinders

    Energy Technology Data Exchange (ETDEWEB)

    Fetecau, C. [GC University, Abdus Salam School of Mathematical Sciences, Lahore (Pakistan); Technical University of Iasi, Department of Mathematics, Iasi (Romania); Fetecau, Corina [Technical University of Iasi, Department of Theoretical Mechanics, Iasi (Romania); Jamil, M. [GC University, Abdus Salam School of Mathematical Sciences, Lahore (Pakistan); NED University of Engineering and Technology, Department of Mathematics, Karachi (Pakistan); Mahmood, A. [GC University, Abdus Salam School of Mathematical Sciences, Lahore (Pakistan); COMSATS Institute of Information Technology, Department of Mathematics, Lahore (Pakistan)

    2011-08-15

    This paper deals with the study of unsteady flow of a Maxwell fluid with fractional derivative model, between two infinite coaxial circular cylinders, using Laplace and finite Hankel transforms. The motion of the fluid is produced by the inner cylinder that, at time t=0{sup +}, is subject to a time-dependent longitudinal shear stress. Velocity field and the adequate shear stress are presented under series form in terms of the generalized G and R functions. The solutions that have been obtained satisfy all imposed initial and boundary conditions. The corresponding solutions for ordinary Maxwell and Newtonian fluids are obtained as limiting cases of general solutions. Finally, the influence of the pertinent parameters on the fluid motion as well as a comparison between the three models is underlined by graphical illustrations. (orig.)

  4. Coaxial carbon plasma gun deposition of amorphous carbon films

    Science.gov (United States)

    Sater, D. M.; Gulino, D. A.; Rutledge, S. K.

    1984-01-01

    A unique plasma gun employing coaxial carbon electrodes was used in an attempt to deposit thin films of amorphous diamond-like carbon. A number of different structural, compositional, and electrical characterization techniques were used to characterize these films. These included scanning electron microscopy, scanning transmission electron microscopy, X ray diffraction and absorption, spectrographic analysis, energy dispersive spectroscopy, and selected area electron diffraction. Optical absorption and electrical resistivity measurements were also performed. The films were determined to be primarily amorphous, with poor adhesion to fused silica substrates. Many inclusions of particulates were found to be present as well. Analysis of these particulates revealed the presence of trace impurities, such as Fe and Cu, which were also found in the graphite electrode material. The electrodes were the source of these impurities. No evidence of diamond-like crystallite structure was found in any of the film samples. Details of the apparatus, experimental procedure, and film characteristics are presented.

  5. Disturbance observer based hierarchical control of coaxial-rotor UAV.

    Science.gov (United States)

    Mokhtari, M Rida; Cherki, Brahim; Braham, Amal Choukchou

    2017-03-01

    This paper propose an hierarchical controller based on a new disturbance observer with finite time convergence (FTDO) to solve the path tracking of a small coaxial-rotor-typs Unmanned Aerial Vehicles (UAVs) despite of unknown aerodynamic efforts. The hierarchical control technique is used to separate the flight control problem into an inner loop that controls attitude and an outer loop that controls the thrust force acting on the vehicle. The new disturbance observer with finite time convergence is intergated to online estimate the unknown uncertainties and disturbances and to actively compensate them in finite time.The analysis further extends to the design of a control law that takes the disturbance estimation procedure into account. Numerical simulations are carried out to demonstrate the efficiency of the proposed control strategy. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  6. Extended State Observer based control for coaxial-rotor UAV.

    Science.gov (United States)

    Rida Mokhtari, M; Choukchou Braham, Amal; Cherki, Brahim

    2016-03-01

    This paper considers the problem of controlling the position and the orientation of a Coaxial-Rotor Unmanned Aerial Vehicle -CRUAV- despite unknown aerodynamic efforts. A hierarchical flight controller is designed, allowing the trajectory tracking and the stabilization of the vehicle. The designed controller is build through a hierarchical approach yielding two control loops, an inner one to control the attitude and an outer one to control the translational trajectory of the rotorcraft. An Extended State Observer -ESO- is used to estimate the state and the unknown aerodynamic disturbances. The analysis further extends to the design of a control law that takes the disturbance estimation procedure into account. Numerical simulations are carried out to demonstrate the efficiency of the proposed control strategy. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

  7. Trilayer TMDC Heterostructures for MOSFETs and Nanobiosensors

    Science.gov (United States)

    Datta, Kanak; Shadman, Abir; Rahman, Ehsanur; Khosru, Quazi D. M.

    2017-02-01

    Two dimensional materials such as transition metal dichalcogenides (TMDC) and their bi-layer/tri-layer heterostructures have become the focus of intense research and investigation in recent years due to their promising applications in electronics and optoelectronics. In this work, we have explored device level performance of trilayer TMDC heterostructure (MoS2/MX2/MoS2; M = Mo or, W and X = S or, Se) metal oxide semiconductor field effect transistors (MOSFETs) in the quantum ballistic regime. Our simulation shows that device `on' current can be improved by inserting a WS2 monolayer between two MoS2 monolayers. Application of biaxial tensile strain reveals a reduction in drain current which can be attributed to the lowering of carrier effective mass with increased tensile strain. In addition, it is found that gate underlap geometry improves electrostatic device performance by improving sub-threshold swing. However, increase in channel resistance reduces drain current. Besides exploring the prospect of these materials in device performance, novel trilayer TMDC heterostructure double gate field effect transistors (FETs) are proposed for sensing Nano biomolecules as well as for pH sensing. Bottom gate operation ensures these FETs operating beyond Nernst limit of 59 mV/pH. Simulation results found in this work reveal that scaling of bottom gate oxide results in better sensitivity while top oxide scaling exhibits an opposite trend. It is also found that, for identical operating conditions, proposed TMDC FET pH sensors show super-Nernst sensitivity indicating these materials as potential candidates in implementing such sensor. Besides pH sensing, all these materials show high sensitivity in the sub-threshold region as a channel material in nanobiosensor while MoS2/WS2/MoS2 FET shows the least sensitivity among them.

  8. Antimonide Heterostructure Nanowires - Growth, Physics and Devices

    OpenAIRE

    Borg, Mattias

    2012-01-01

    This thesis investigates the growth and application of antimonide heterostructure nanowires for low-power electronics. In the first part of the thesis, GaSb, InSb and InAsSb nanowire growth is presented, and the distinguishing features of the growth are described. It is found that the presence of Sb results in more than 50 at. % group-III concentration in the Au seed particle on top of the nanowires. It is further concluded that the effective V/III ratio inside the seed particle is reduced co...

  9. Exciton broadening in WS2/graphene heterostructures

    Science.gov (United States)

    Hill, Heather M.; Rigosi, Albert F.; Raja, Archana; Chernikov, Alexey; Roquelet, Cyrielle; Heinz, Tony F.

    2017-11-01

    We have used optical spectroscopy to observe spectral broadening of WS2 exciton reflectance peaks in heterostructures of monolayer WS2 capped with mono- to few-layer graphene. The broadening is found to be similar for the A and B excitons and on the order of 5-10 meV. No strong dependence on the number of graphene layers was observed within experimental uncertainty. The broadening can be attributed to charge- and energy-transfer processes between the two materials, providing an observed lower bound for the corresponding time scales of 65 fs.

  10. Carbon nanotube solar cells.

    Directory of Open Access Journals (Sweden)

    Colin Klinger

    Full Text Available We present proof-of-concept all-carbon solar cells. They are made of a photoactive side of predominantly semiconducting nanotubes for photoconversion and a counter electrode made of a natural mixture of carbon nanotubes or graphite, connected by a liquid electrolyte through a redox reaction. The cells do not require rare source materials such as In or Pt, nor high-grade semiconductor processing equipment, do not rely on dye for photoconversion and therefore do not bleach, and are easy to fabricate using a spray-paint technique. We observe that cells with a lower concentration of carbon nanotubes on the active semiconducting electrode perform better than cells with a higher concentration of nanotubes. This effect is contrary to the expectation that a larger number of nanotubes would lead to more photoconversion and therefore more power generation. We attribute this to the presence of metallic nanotubes that provide a short for photo-excited electrons, bypassing the load. We demonstrate optimization strategies that improve cell efficiency by orders of magnitude. Once it is possible to make semiconducting-only carbon nanotube films, that may provide the greatest efficiency improvement.

  11. Optimal estimation of ship's attitudes for beampattern corrections in a coaxial circular array

    Digital Repository Service at National Institute of Oceanography (India)

    Chakraborty, B.; Dev, K.K.

    A study is conducted to estimate the accurate attitude of a ship's motion and the estimation is used to arrive at the corrections required for a farfield pattern of a coaxial circular array. The relevant analytical expression is developed...

  12. Photoresponse of Natural van der Waals Heterostructures.

    Science.gov (United States)

    Ray, Kyle; Yore, Alexander E; Mou, Tong; Jha, Sauraj; Smithe, Kirby K H; Wang, Bin; Pop, Eric; Newaz, A K M

    2017-06-27

    Van der Waals heterostructures consisting of two-dimensional materials offer a platform to obtain materials by design and are very attractive owing to unique electronic states. Research on 2D van der Waals heterostructures (vdWH) has so far been focused on fabricating individually stacked atomically thin unary or binary crystals. Such systems include graphene, hexagonal boron nitride, and members of the transition metal dichalcogenide family. Here we present our experimental study of the optoelectronic properties of a naturally occurring vdWH, known as franckeite, which is a complex layered crystal composed of lead, tin, antimony, iron, and sulfur. We present here that thin film franckeite (60 nm < d < 100 nm) behaves as a narrow band gap semiconductor demonstrating a wide-band photoresponse. We have observed the band-edge transition at ∼1500 nm (∼830 meV) and high external quantum efficiency (EQE ≈ 3%) at room temperature. Laser-power-resolved and temperature-resolved photocurrent measurements reveal that the photocarrier generation and recombination are dominated by continuously distributed trap states within the band gap. To understand wavelength-resolved photocurrent, we also calculated the optical absorption properties via density functional theory. Finally, we have shown that the device has a fast photoresponse with a rise time as fast as ∼1 ms. Our study provides a fundamental understanding of the optoelectronic behavior in a complex naturally occurring vdWH, and may pave an avenue toward developing nanoscale optoelectronic devices with tailored properties.

  13. Tunable multiwalled nanotube resonator

    Science.gov (United States)

    Jensen, Kenneth J; Girit, Caglar O; Mickelson, William E; Zettl, Alexander K; Grossman, Jeffrey C

    2013-11-05

    A tunable nanoscale resonator has potential applications in precise mass, force, position, and frequency measurement. One embodiment of this device consists of a specially prepared multiwalled carbon nanotube (MWNT) suspended between a metal electrode and a mobile, piezoelectrically controlled contact. By harnessing a unique telescoping ability of MWNTs, one may controllably slide an inner nanotube core from its outer nanotube casing, effectively changing its length and thereby changing the tuning of its resonance frequency. Resonant energy transfer may be used with a nanoresonator to detect molecules at a specific target oscillation frequency, without the use of a chemical label, to provide label-free chemical species detection.

  14. Nanotube resonator devices

    Science.gov (United States)

    Jensen, Kenneth J; Zettl, Alexander K; Weldon, Jeffrey A

    2014-05-06

    A fully-functional radio receiver fabricated from a single nanotube is being disclosed. Simultaneously, a single nanotube can perform the functions of all major components of a radio: antenna, tunable band-pass filter, amplifier, and demodulator. A DC voltage source, as supplied by a battery, can power the radio. Using carrier waves in the commercially relevant 40-400 MHz range and both frequency and amplitude modulation techniques, successful music and voice reception has been demonstrated. Also disclosed are a radio transmitter and a mass sensor using a nanotube resonator device.

  15. High speed data transmission coaxial-cable in the space communication system

    Science.gov (United States)

    Su, Haohang; Huang, Jing

    2018-01-01

    An effective method is proved based on the scattering parameter of high speed 8-core coaxial-cable measured by vector network analyzer, and the semi-physical simulation is made to receive the eye diagram at different data transmission rate. The result can be apply to analysis decay and distortion of the signal through the coaxial-cable at high frequency, and can extensively design for electromagnetic compatibility of high-speed data transmission system.

  16. Frequency selective properties of coaxial transmission lines loaded with combined artificial inclusions.

    Science.gov (United States)

    Falcone, Francisco; Gil, Javier

    2014-01-01

    The properties of a modified coaxial transmission line by periodic inclusions will be discussed. The introduction of split ring resonators, conductor stubs, air gaps, and combination of these gives rise to new frequency selective properties, such as stopband or passband behavior, observable in planar as well as volumetric metamaterial structures. These results envisage new potential applications and implementation of devices in coaxial transmission line technology.

  17. Frequency Selective Properties of Coaxial Transmission Lines Loaded with Combined Artificial Inclusions

    Directory of Open Access Journals (Sweden)

    Francisco Falcone

    2014-01-01

    Full Text Available The properties of a modified coaxial transmission line by periodic inclusions will be discussed. The introduction of split ring resonators, conductor stubs, air gaps, and combination of these gives rise to new frequency selective properties, such as stopband or passband behavior, observable in planar as well as volumetric metamaterial structures. These results envisage new potential applications and implementation of devices in coaxial transmission line technology.

  18. Preliminary investigation of power flow and electrode phenomena in a multi-megawatt coaxial plasma thruster

    Science.gov (United States)

    Schoenberg, Kurt; Gerwin, Richard; Henins, Ivars; Mayo, Robert; Scheuer, Jay; Nurden, Glen

    1993-01-01

    This paper summarizes preliminary experimental and theoretical research that was directed towards the study of quasisteady-state power flow in a large, un-optimized, multi-megawatt coaxial plasma thruster. The report addresses large coaxial thruster operation and includes evaluation and interpretation of the experimental results with a view to the development of efficient, steady-state megawatt-class magnetoplasmadynamic (MPD) thrusters.

  19. Microwave generation enhancement of X-band CRBWO by use of coaxial dual annular cathodes

    OpenAIRE

    Yan Teng; Jun Sun; Changhua Chen; Hao Shao

    2013-01-01

    This paper presents an approach that greatly enhances both the output power and the conversion efficiency of the coaxial relativistic backward wave oscillator (CRBWO) by using coaxial dual annular cathodes, which increases the diode current rather than the diode voltage. The reasons for the maladjustment of CRBWO under a high diode voltage are analyzed theoretically. It is found that by optimization of the diode structure, the shielding effect of the space charge of the outer beams on the inn...

  20. On the jets, kinks, and spheromaks formed by a planar magnetized coaxial gun

    OpenAIRE

    Hsu, S. C.; Bellan, P. M.

    2004-01-01

    Measurements of the various plasma configurations produced by a planar magnetized coaxial gun provide insight into the magnetic topology evolution resulting from magnetic helicity injection. Important features of the experiments are a very simple coaxial gun design so that all observed geometrical complexity is due to the intrinsic physical dynamics rather than the source shape and use of a fast multiple-frame digital camera which provides direct imaging of topologically complex shapes and dy...

  1. Transport in Carbon Nanotubes

    Science.gov (United States)

    Datta, S.; Xue, Yong-Qinag; Anantram, M. P.; Saini, Subhash (Technical Monitor)

    1999-01-01

    This presentation discusses coupling between carbon nanotubes (CNT), simple metals (FEG) and a graphene sheet. The graphene sheet did not couple well with FEG, but the combination of a graphene strip and CNT did couple well with most simple metals.

  2. Carbon nanotubes for supercapacitor

    National Research Council Canada - National Science Library

    Pan, Hui; Li, Jianyi; Feng, Yuanping

    2010-01-01

    .... The purpose is to give a comprehensive understanding of the advantages and disadvantages of carbon nanotubes-related supercapacitor materials and to find ways for the improvement in the performance of supercapacitor...

  3. Carbon nanotube biosensors

    National Research Council Canada - National Science Library

    Tîlmaciu, Carmen-Mihaela; Morris, May C

    2015-01-01

    .... In particular, carbon nanotubes (CNTs) can serve as scaffolds for immobilization of biomolecules at their surface, and combine several exceptional physical, chemical, electrical, and optical characteristics properties which make them one...

  4. One-dimensional hole gas in germanium/silicon nanowire heterostructures

    Science.gov (United States)

    Lu, Wei; Xiang, Jie; Timko, Brian P.; Wu, Yue; Lieber, Charles M.

    2005-07-01

    Two-dimensional electron and hole gas systems, enabled through band structure design and epitaxial growth on planar substrates, have served as key platforms for fundamental condensed matter research and high-performance devices. The analogous development of one-dimensional (1D) electron or hole gas systems through controlled growth on 1D nanostructure substrates, which could open up opportunities beyond existing carbon nanotube and nanowire systems, has not been realized. Here, we report the synthesis and transport studies of a 1D hole gas system based on a free-standing germanium/silicon (Ge/Si) core/shell nanowire heterostructure. Room temperature electrical transport measurements clearly show hole accumulation in undoped Ge/Si nanowire heterostructures, in contrast to control experiments on single-component nanowires. Low-temperature studies show well-controlled Coulomb blockade oscillations when the Si shell serves as a tunnel barrier to the hole gas in the Ge channel. Transparent contacts to the hole gas also have been reproducibly achieved by thermal annealing. In such devices, we observe conductance quantization at low temperatures, corresponding to ballistic transport through 1D subbands, where the measured subband energy spacings agree with calculations for a cylindrical confinement potential. In addition, we observe a “0.7 structure,” which has been attributed to spontaneous spin polarization, suggesting the universality of this phenomenon in interacting 1D systems. Lastly, the conductance exhibits little temperature dependence, consistent with our calculation of reduced backscattering in this 1D system, and suggests that transport is ballistic even at room temperature. Author contributions: W.L., J.X., and C.M.L. designed research; W.L. and J.X. performed research; B.P.T. and Y.W. contributed new reagents/analytic tools; W.L., J.X., and C.M.L. analyzed data; W.L., J.X., and C.M.L. wrote the paper; and B.P.T. and Y.W. developed growth of nanowire

  5. Morphing Carbon Nanotube Microstructures

    Science.gov (United States)

    2015-02-20

    muscle inspired by spider dragline silk. Nat. Commun. 5, 3322 (2014). 13. Hart, A. J. & Slocum , A. H. Rapid Growth and Flow-Mediated Nucleation of...Phys. Lett. 87, 123110 (2005). 15. A. J. Hart, A. H. Slocum . Rapid growth and flow-mediated nucleation of millimeter-scale aligned carbon nanotube... Slocum , B. L. Wardle. High-yield growth and morphology control of aligned carbon nanotubes on ceramic fibers for multifunctional enhancement of

  6. Boron Nitride Nanotubes

    Science.gov (United States)

    Smith, Michael W. (Inventor); Jordan, Kevin (Inventor); Park, Cheol (Inventor)

    2012-01-01

    Boron nitride nanotubes are prepared by a process which includes: (a) creating a source of boron vapor; (b) mixing the boron vapor with nitrogen gas so that a mixture of boron vapor and nitrogen gas is present at a nucleation site, which is a surface, the nitrogen gas being provided at a pressure elevated above atmospheric, e.g., from greater than about 2 atmospheres up to about 250 atmospheres; and (c) harvesting boron nitride nanotubes, which are formed at the nucleation site.

  7. Carbon Nanotubes in Neuroscience

    OpenAIRE

    Malarkey, Erik B.; Parpura, Vladimir

    2010-01-01

    Carbon nanotubes have electrical, mechanical and chemical properties that make them one of the most promising materials for applications in neuroscience. Single-walled and multi-walled carbon nanotubes have been increasingly used as scaffolds for neuronal growth and more recently for neural stem cell growth and differentiation. They are also used in interfaces with neurons, where they can detect neuronal electrical activity and also deliver electrical stimulation to these cells. The emerging ...

  8. Ge/Si core/multi shell heterostructure FETs

    Energy Technology Data Exchange (ETDEWEB)

    Picraux, Samuel T [Los Alamos National Laboratory; Dayeh, Shadi A [Los Alamos National Laboratory

    2010-01-01

    Concentric heterostructured materials provide numerous design opportunities for engineering strain and interfaces, as well as tailoring energy band-edge combinations for optimal device performance. Key to the realization of such novel device concepts is the complete understanding and full control over their growth, crystal structure, and hetero-epitaxy. We report here on a new route for synthesizing Ge/Si core/multi-shell heterostructure nanowires that eliminate Au seed diffusion on the nanowire sidewalls by engineering the interface energy density difference. We show that such control over core/shell synthesis enable experimental realization of heterostructure FET devices beyond those available in the literature with enhanced transport characteristics. We provide a side-by-side comparison on the transport properties of Ge/Si core/multi-shell nanowires grown with and without Au diffusion and demonstrate heterostructure FETs with drive currents that are {approx} 2X higher than record results for p-type FETs.

  9. Engineering charge transport by heterostructuring solution-processed semiconductors

    Science.gov (United States)

    Voznyy, Oleksandr; Sutherland, Brandon R.; Ip, Alexander H.; Zhitomirsky, David; Sargent, Edward H.

    2017-06-01

    Solution-processed semiconductor devices are increasingly exploiting heterostructuring — an approach in which two or more materials with different energy landscapes are integrated into a composite system. Heterostructured materials offer an additional degree of freedom to control charge transport and recombination for more efficient optoelectronic devices. By exploiting energetic asymmetry, rationally engineered heterostructured materials can overcome weaknesses, augment strengths and introduce emergent physical phenomena that are otherwise inaccessible to single-material systems. These systems see benefit and application in two distinct branches of charge-carrier manipulation. First, they influence the balance between excitons and free charges to enhance electron extraction in solar cells and photodetectors. Second, they promote radiative recombination by spatially confining electrons and holes, which increases the quantum efficiency of light-emitting diodes. In this Review, we discuss advances in the design and composition of heterostructured materials, consider their implementation in semiconductor devices and examine unexplored paths for future advancement in the field.

  10. Magnetic Heterostructures Advances and Perspectives in Spinstructures and Spintransport

    CERN Document Server

    Bader, Samuel D

    2008-01-01

    Magnetic heterostructures constitute an important field in magnetism and nanotechnology, which has developed over the past fifteen years due to important advances in epitaxial- growth techniques and lithographic processes. Magnetic heterostructures combine different physical properties which do not exist in nature. Examples are semiconductors/ferromagnets, superconductors/ferromagnets, and ferromagnets/antiferromagnets. These combinations display rich and novel physical properties different from those that exit in any single one of them. Interlayer exchange coupling, exchange bias, proximity effects, giant magneto-resistance, tunneling magneto-resistance, spininjection and spintransport are examples of new physical phenomena that rely on the combination of different materials layers. Since the literature on magnetic heterostructures is widely spread and highly specialized, the situation calls for a book that provides an overview of the basics and the state of the art of magnetic heterostructures. These contri...

  11. Seed-mediated growth of ZnO nanorods on multiwalled carbon nanotubes.

    Science.gov (United States)

    Li, Changqing; Jin, Zhong; Chu, Haibin; Li, Yan

    2008-09-01

    The heterostructures of ZnO nanorods on multiwalled carbon nanotubes (MWNTs) were fabricated by a seed-mediated growth method. First, the surfaces of the carbon nanotubes (CNTs) were coated in situ with mono-dispersed ZnO nanocrystals of about 7 nm by the reaction of zinc acetate and sodium hydroxide. These nanocrystals were then served as the seeds for further growth of ZnO nanorods. In the second step, ZnO nanorods were grown on MWNTs coated with ZnO nanocrystals in an aqueous solution of zinc nitrate and equimolar hexamethylenetetramine at 85 degrees C. Typically, the ZnO nanorods had the length of 300-600 nm and the diameter of 40-140 nm and took a random direction on the outside walls of MWNTs. The morphology of the ZnO nanorods was dependent on pH, reactant concentration, and growing time.

  12. Focus Ion Beam Fabrication of Individual Carbon Nanotube Field Emission Tips

    Science.gov (United States)

    Chai, Guangyu; Byahut, Sitaram; Chow, Lee

    2003-11-01

    Individual CNTs are excellent candidates as electron sources for electron microscopes. Comparing to conventional electron sources, CNTs have the following advantages: (1) unique geometry, (2) highly coherent electron beams, and (3) stability. In our laboratory, carbon fibers with a nanotube core have been synthesized with a conventional chemical vapor deposition method. The whole assembly of nanotube/fiber is similar to a coaxial cable with CNT sticking out from one end of the carbon fiber. In order to pick up individual CNT field emitters, focus ion beam (FIB) technique is applied for cutting and adhering the samples. The carbon fiber with nanotube tip was first welded onto a micro-manipulator. Afterwards, by applying the FIB milling function, the fiber was cut from the base. This enables us to handle the individual CNT tips conveniently. By the same method, we can attach the nanotube tip on a sharpened clean tungsten wire for field emission experiment. FIB is proven to be appropriate and powerful for the nano-fabrication.

  13. Energy Loss to Coaxial Vacuum Chambers in LEP and LHC

    CERN Document Server

    Gluckstern, R L

    1996-01-01

    In many hig-energy storage rings the beam chamber is connected to a separate pump chamber by a metallic wall with many holes or slots whic permits passage of the rest gas. In LEP, the pump chamber contains a metallic 'negstrip' pump, and thereby becomes a coazial transmission line. Also in LHC, a coaxial line is formed by the 'liner' and the surrounding cold vacuum chamber which it shields from heating by sznchrotron radiation. Since the phase velocity of electro-magnetic fields in a coax line is close to light velocity, the fields will be almost in sznchronism with the particle beam and the pump chamber, which may result in a large resistive impedance and could lead to isntability, loss of beam energy, and excessive heating of the chamber walls. Here we estimate the rate of field buildup analytically, and in a subsequent report we will compare these results with numerical computations using 3-D computer codes. The results are tested for diagnostic purposes on a 'slot coupler' with short and wide holes design...

  14. Essential Oil Bioactive Fibrous Membranes Prepared via Coaxial Electrospinning.

    Science.gov (United States)

    Yao, Zhi-Cheng; Chen, Si-Cong; Ahmad, Zeeshan; Huang, Jie; Chang, Ming-Wei; Li, Jing-Song

    2017-06-01

    A novel antimicrobial composite material was prepared by encapsulating orange essential oil (OEO) in zein prolamine (ZP) via the coaxial electrospinning (ES) technique. By manipulating process parameters, the morphological features of ZP/OEO fibers were modulated. Fine fibers with diameters ranging from 0.7 to 2.3 μm were obtained by regulating ZP solution concentration and process parameters during the ES process. Optimal loading capacity (LC) and encapsulation efficiency (EE) of OEO in fibrous ZP mats were determined to be 22.28% and 53.68%, respectively, and were achieved using a 35 w/v% ZP ES solution. The encapsulation of OEO was found to be reliant on ZP solution concentration (the enveloping medium). SEM analysis indicates the surface morphology of ZP/OEO electrospun fibers is dependent on ZP solution loading volume, with lower ZP concentrations yielding defective fibrous structures (for example, beaded and spindled-string like morphologies). Furthermore, this loading volume also influences OEO LC, EE, mat water contact angle and oil retention. CCK-8 assay and cell morphology assessment (HEK293T cells) indicate no significant change with electrospun ZP and ZP/OEO fibrous membranes over an 8 h period. Antimicrobial activity assessment using Escherichia coli, suggests composite nonwovens possess sterilization properties; elucidating potential application in active food packaging, food preservation and therefore sustainability. © 2017 Institute of Food Technologists®.

  15. Research of Driving Circuit in Coaxial Induction Coilgun

    Directory of Open Access Journals (Sweden)

    Yadong Zhang

    2013-09-01

    Full Text Available Power supply is crucial equipment in coaxial induction coil launcher.Configuration of the driving circuit influences the efficiency of the coil launcher directly.This paper gives a detailed analysis of the properties of the driving circuit construction based on the capacitor source. Three topologies of the driving circuit are compared including oscillation circuit, crowbar circuit and half-wave circuit. It is proved that which circuit has the better efficiency depends on the detailed parameters of the experiment, especially the crowbar resistance. Crowbar resistor regulates not only efficiency of the system, but also temperature rise of the coil. Electromagnetic force (EMF applied on the armature will be another question which influences service condition of the driving circuits. Oscillation circuit and crowbar circuit should apply to the asynchronous induction coil launcher and synchronous induction coil launcher, respectively. Half-wave circuit is seldom used in the experiment. Although efficiency of the half-wave circuit is very high, the speed of the armature is low. A simple independent half-wave circuit is suggested in this paper. Generally speaking, the comprehensive property of crowbar circuit is the most practical in the three typical circuits. Conclusions of the paper could provide guidelines for practice.

  16. Plastic Collapse Localisation in Simple Shearing and Coaxial Deformations

    Science.gov (United States)

    Hobbs, B. E.; Ord, A.

    2011-12-01

    We explore, numerically, the evolution of localisation due to plastic collapse in both coaxial shortening and simple shearing deformations. These localisation features arise from plastic behaviour and hence differ from the formation of anticracks modelled by linear elastic behaviour (Fletcher and Pollard, 1990). The behaviour is close to that discussed by Rudnicki (2004) and Chemenda (2009) in that localisation consists of zones of plastic collapse separated by elastically unloaded regions. The constitutive behaviour assumed here comprises a Tresca yield with both strain-softening of the yield stress and of a cap that models plastic volumetric collapse during phase transformations, such as the olivine-spinel transition, with ΔVSudbury, Ontario, Canada, October 2003. R. Brummer (Ed), Balkema, 27-33. Fletcher, R.C., Pollard, D.D., 1990. Anticrack model for pressure solution surfaces. Geology 9, 419- 424. Green, H.W., Burnley, P.C., 1989. A new self-organizing mechanism for deep-focus earthquakes. Nature, 341, 733- 737. Issen, K.A., Rudnicki, J.W., 2000. Conditions for compaction bands in porous rocks. J. Geophys. Res. 105, 21,529-21,536. Rudnicki, J. W. 2004. Shear and compaction band formation on an elliptic yield cap. J. Geophys. Res., 109, B03402. Veveakis, E., Alevizos, S., & Vardoulakis, I. 2010. Chemical reaction capping of thermal instabilities during shear of frictional faults. Journal of the Mechanics and Physics of Solids. 58, 1175-1194.

  17. Organic heterostructures deposited by MAPLE on AZO substrate

    Science.gov (United States)

    Socol, M.; Preda, N.; Stanculescu, A.; Breazu, C.; Florica, C.; Stanculescu, F.; Iftimie, S.; Girtan, M.; Popescu-Pelin, G.; Socol, G.

    2017-09-01

    Organic heterostructures based on poly(3-hexylthiophene) (P3HT) and fullerene (C60) as blends or multilayer were deposited on Al:ZnO (AZO) by Matrix-Assisted Pulsed Laser Evaporation (MAPLE) technique. The AZO layers were obtained by Pulsed Laser Deposition (PLD) on glass substrate, the high quality of the films being reflected by the calculated figure of merit. The organic heterostructures were investigated from morphological, optical and electrical point of view by atomic force microscopy (AFM), UV-vis spectroscopy, photoluminescence (PL) and current-voltage (I-V) measurements, respectively. The increase of the C60 content in the blend heterostructure has as result a high roughness. Compared with the multilayer heterostructure, those based on blends present an improvement in the electrical properties. Under illumination, the highest current value was recorded for the heterostructure based on the blend with the higher C60 amount. The obtained results showed that MAPLE is a useful technique for the deposition of the organic heterostructures on AZO as transparent conductor electrode.

  18. Synthesis and characterization of germanium nanowires and germanium/silicon radially heterostructured nanowires

    Science.gov (United States)

    Goldthorpe, Irene Anne

    Semiconductor nanowires offer new opportunities to study physical phenomena in low-dimensional nanostructures. They also possess technologically useful properties for applications in electronics, optics, sensing, and thermoelectrics. Germanium nanowires are of particular interest, because of germanium's compatibility with standard silicon integrated circuit fabrication processes, its high electronic carrier mobilities, and the low temperature required for germanium nanowire growth. In this work, epitaxially-aligned germanium nanowires are grown on silicon substrates by chemical vapor deposition through the vapor-liquid-solid mechanism. Uniform nanowire diameters between 5 and 50 nm are obtained through the use of monodisperse gold colloids as catalysts. The crystallographic orientation of the nanowires, their strain, and their heteroepitaxial relationship with the substrate are characterized with transmission electron microscopy (TEM) and x-ray diffraction (XRD). A process for removing the gold catalysts from the tips of the germanium nanowires is demonstrated. Silicon shells are then heteroepitaxially deposited around the wires to fabricate radial heterostructures. These shells passivate the germanium nanowire surface, create electronic band offsets to confine holes away the surface where they can scatter or recombine, and induce strain which could allow for the engineering of properties such as band gap and carrier mobilities. However, analogous to planar heteroepitaxy, surface roughening and misfit dislocations can relax this strain. The effects of coaxial dimensions on strain relaxation in these structures are analyzed quantitatively by TEM and synchrotron XRD, and these results are related to continuum elasticity models. Lessons learned generated two successful strategies for synthesizing coherent core-shell nanowires with large misfit strain: chlorine surface passivation and growth of nanowires with low-energy sidewall facets. Both approaches avoid the strain

  19. Quantum and field effects of oxide heterostructures

    DEFF Research Database (Denmark)

    Trier, Felix

    . In these multi-plexed devices, several inputs aretranslated into several outputs through the multiple physical functionalities.A highly prominent example of such an oxide interface is the one between LaAlO3 and SrTiO3. Although both LaAlO3 and SrTiO3 in the bulk are electrically insulating and non...... aspects of sample preparation will initially be covered. Here, the growth of amorphous-LaAlO3 on SrTiO3 will be addressed in a modified pulsed laser deposition setup. This is followed by an investigation of two high-electron mobility interfaces in SrTiO3-based heterostructures. Specifically...

  20. Magnetoelectric imaging of multiferroic heterostructures (Presentation Recording)

    Science.gov (United States)

    Ghidini, Massimo; Lesaine, Arnaud; Zhu, Bonan; Moya, Xavier; Yan, Wenjing; Crossley, Sam; Nair, Bhasi; Mansell, Rhodri; Cowburn, Russell P.; Barnes, Crispin H. W.; Kronast, Florian; Valencia, Sergio; Maccherozzi, Francesco; Dhesi, Sarnjeet S.; Mathur, Neil

    2015-09-01

    Electrical control of magnetism has been demonstrated in multiferroic compounds and ferromagnetic semiconductors, but electrical switching of a substantial net magnetization at room temperature has not been demonstrated in these materials. This goal has instead been achieved in heterostructures comprising ferromagnetic films in which electrically driven magnetic changes arise due to strain or exchange bias from ferroic substrates, or due to charge effects induced by a gate. However, previous work focused on electrical switching of an in-plane magnetization or involved the assistance of applied magnetic fields. In heterostructures made of juxtaposed ferroelectric and ferromagnetic layers, we have shown electrical control with no applied magnetic field of the perpendicular magnetization of small features [1] and of magnetic stripe domains patterns [2]. Here we investigate Ni81Fe19 films on ferroelectric substrates with and without buffer layers of Cu, whose presence precludes charge-mediated coupling. Ni81Fe19 has virtually zero magnetostriction, but sufficiently thin films show large magnetostriction, and thus, on increasing film thickness through the threshold for zero magnetostriction, we have seeked the crossover from charge- to strain-mediated coupling. We will then show that strain associated with the motion of 90°- ferroelectric domain walls in a BaTiO3 substrate, can switch the magnetization of an array of overlying single-domain Ni dots. [1] M. Ghidini, R. Pellicelli, J. L. Prieto, X. Moya, J. Soussi, J. Briscoe, S. Dunn and N. D. Mathur, Nature Communications 4 (2013) 1453. [2] M. Ghidini, F.Maccherozzi, X. Moya, L. C. Phillips, W.Yan, J. Soussi, N. Métallier, M.Vickers, , N. -J.Steinke, R. Mansell, C. H. W. Barnes, S. S. Dhesi, and N. D. Mathur, Adv. Mater.doi: 10.1002/adma.201404799 (2015).

  1. Carbon nanotube junctions and devices

    NARCIS (Netherlands)

    Postma, H.W.Ch.

    2001-01-01

    In this thesis Postma presents transport experiments performed on individual single-wall carbon nanotubes. Carbon nanotubes are molecules entirely made of carbon atoms. The electronic properties are determined by the exact symmetry of the nanotube lattice, resulting in either metallic or

  2. Elastic properties of noncarbon nanotubes as compared to carbon nanotubes

    Science.gov (United States)

    Kochaev, Aleksey

    2017-10-01

    A comparative study of stability, structural, and elastic properties of single-wall noncarbon nanotubes, including BN, AlN, GaN, AlP, GaP, and B nanotubes using ab initio simulation is presented. The proposed nanotubes can be found in nature, which is confirmed by calculation of their binding energy. The values of Young's modulus and Poisson's ratio for (0,n ) and (n ,n ) proposed nanotubes with n =3 ⋯20 are obtained. The conception of two-dimensional (2D) Young's modulus of planar and tubular materials was developed. The calculations show that stable forms of boron nitride nanotubes have the 2D Young's modulus almost similar to carbon nanotubes. At the same time, it is stated that boron nanotubes have a higher 2D Young's modulus than any other known carbon and noncarbon nanostructures.

  3. An experimental investigation of reacting and nonreacting coaxial jet mixing in a laboratory rocket engine

    Science.gov (United States)

    Schumaker, Stephen Alexander

    Coaxial jets are commonly used as injectors in propulsion and combustion devices due to both the simplicity of their geometry and the rapid mixing they provide. In liquid rocket engines it is common to use coaxial jets in the context of airblast atomization. However, interest exists in developing rocket engines using a full flow staged combustion cycle. In such a configuration both propellants are injected in the gaseous phase. In addition, gaseous coaxial jets have been identified as an ideal test case for the validation of the next generation of injector modeling tools. For these reasons an understanding of the fundamental phenomena which govern mixing in gaseous coaxial jets and the effect of combustion on these phenomena in coaxial jet diffusion flames is needed. A study was performed to better understand the scaling of the stoichiometric mixing length in reacting and nonreacting coaxial jets with velocity ratios greater than one and density ratios less than one. A facility was developed that incorporates a single shear coaxial injector in a laboratory rocket engine capable of ten atmospheres. Optical access allows the use of flame luminosity and laser diagnostic techniques such as Planar Laser Induced Fluorescence (PLIF). Stoichiometric mixing lengths (LS), which are defined as the distance along the centerline where the stoichiometric condition occurs, were measured using PLIF. Acetone was seeded into the center jet to provide direct PLIF measurement of the average and instantaneous mixture fraction fields for a range of momentum flux ratios for the nonreacting cases. For the coaxial jet diffusion flames, LS was measured from OH radical contours. For nonreacting cases the use of a nondimensional momentum flux ratio was found to collapse the mixing length data. The flame lengths of coaxial jet diffusion flames were also found to scale with the momentum flux ratio but different scaling constants are required which depended on the chemistry of the reaction. The

  4. Soldering of Nanotubes onto Microelectrodes

    DEFF Research Database (Denmark)

    Madsen, Dorte Nørgaard; Mølhave, Kristian; Mateiu, Ramona Valentina

    2003-01-01

    Suspended bridges of individual multiwalled carbon nanotubes were fabricated inside a scanning electron microscope by soldering the nanotube onto microelectrodes with highly conducting gold-carbon material. By the decomposition of organometallic vapor with the electron beam, metal-containing solder...... bonds were formed at the intersection of the nanotube and the electrodes. Current-voltage curves indicated metallic conduction of the nanotubes, with resistances in the range of 9-29 kOmega. Bridges made entirely of the soldering material exhibited resistances on the order of 100 Omega, and the solder...... bonds were consistently found to be mechanically stronger than the carbon nanotubes....

  5. Coaxial two-channel high-gradient dielectric wakefield accelerator

    Directory of Open Access Journals (Sweden)

    G. V. Sotnikov

    2009-06-01

    Full Text Available A new scheme for a dielectric wakefield accelerator is proposed that employs a cylindrical multizone dielectric structure configured as two concentric dielectric tubes with outer and inner vacuum channels for drive and accelerated bunches. Analytical and numerical studies have been carried out for such coaxial dielectric-loaded structures (CDS for high-gradient acceleration. An analytical theory of wakefield excitation by particle bunches in a multizone CDS has been formulated. Numerical calculations are presented for an example of a CDS using dielectric tubes with dielectric permittivity 5.7, having external diameters of 2.121 and 0.179 mm with inner diameters of 2.095 and 0.1 mm. An annular 5 GeV, 6 nC electron bunch with rms length of 0.035 mm energizes a wakefield on the structure axis having an accelerating gradient of ∼600  MeV/m with a transformer ratio ∼8∶1. The period of the accelerating field is ∼0.33  mm. If the width of the drive bunch channel is decreased, it is possible to obtain an accelerating gradient of >1  GeV/m while keeping the transformer ratio approximately the same. Full numerical simulations using a particle-in-cell code have confirmed results of the linear theory and furthermore have shown the important influence of the quenching wave that restricts the region of the wakefield to within several periods following the drive bunch. Numerical simulations for another example have shown nearly stable transport of drive and accelerated bunches through the CDS, using a short train of drive bunches.

  6. Theoretical analysis to investigate thermal performance of co-axial heat pipe solar collector

    Science.gov (United States)

    Azad, E.

    2011-12-01

    The thermal performance of co-axial heat pipe solar collector which consist of a collector 15 co-axial heat pipes surrounded by a transparent envelope and which heat a fluid flowing through the condenser tubes have been predicted using heat transfer analytical methods. The analysis considers conductive and convective losses and energy transferred to a fluid flowing through the collector condenser tubes. The thermal performances of co-axial heat pipe solar collector is developed and are used to determine the collector efficiency, which is defined as the ratio of heat taken from the water flowing in the condenser tube and the solar radiation striking the collector absorber. The theoretical water outlet temperature and efficiency are compared with experimental results and it shows good agreement between them. The main advantage of this collector is that inclination of collector does not have influence on performance of co-axial heat pipe solar collector therefore it can be positioned at any angle from horizontal to vertical. In high building where the roof area is not enough the co-axial heat pipe solar collectors can be installed on the roof as well as wall of the building. The other advantage is each heat pipe can be topologically disconnected from the manifold.

  7. Controlled release behaviour of protein-loaded microparticles prepared via coaxial or emulsion electrospray

    Science.gov (United States)

    Wang, Ying; Yang, Xiaoping; Liu, Wentao; Zhang, Feng; Cai, Qing; Deng, Xuliang

    2013-01-01

    Biodegradable poly (lactic-co-glycolic acid) (PLGA) microparticles are an effective way to achieve sustained drug release. In this study, we investigated a sustained release model of PLGA microparticles with incorporated protein via either emulsion or coaxial electrospray techniques. PLGA (75:25) was used as the carrier, and bovine serum albumin as a model protein. Coaxial electrospray resulted in a type of core–shell structure with mean diameters of 2.41 ± 0.60 µm and a centralised protein distribution within the core. Emulsion electrospray formed bigger microparticles with mean diameters of 22.75 ± 8.05 µm and a heterogeneous protein distribution throughout the microparticles. The coaxial electrospray microparticles presented a much slighter burst release than the emulsion electrospray microparticles. Loading efficiency was significantly higher (p < 0.05) in the coaxial group than emulsion group. This indicated that both emulsion and coaxial electrospray could produce protein-loaded microparticles with sustained release behaviour, but the former revealed a superior approach for drug delivery. PMID:23346923

  8. Experimental design and instability analysis of coaxial electrospray process for microencapsulation of drugs and imaging agents.

    Science.gov (United States)

    Si, Ting; Zhang, Leilei; Li, Guangbin; Roberts, Cynthia J; Yin, Xiezhen; Xu, Ronald

    2013-07-01

    Recent developments in multimodal imaging and image-guided therapy requires multilayered microparticles that encapsulate several imaging and therapeutic agents in the same carrier. However, commonly used microencapsulation processes have multiple limitations such as low encapsulation efficiency and loss of bioactivity for the encapsulated biological cargos. To overcome these limitations, we have carried out both experimental and theoretical studies on coaxial electrospray of multilayered microparticles. On the experimental side, an improved coaxial electrospray setup has been developed. A customized coaxial needle assembly combined with two ring electrodes has been used to enhance the stability of the cone and widen the process parameter range of the stable cone-jet mode. With this assembly, we have obtained poly(lactide-co-glycolide) microparticles with fine morphology and uniform size distribution. On the theoretical side, an instability analysis of the coaxial electrified jet has been performed based on the experimental parameters. The effects of process parameters on the formation of different unstable modes have been studied. The reported experimental and theoretical research represents a significant step toward quantitative control and optimization of the coaxial electrospray process for microencapsulation of multiple drugs and imaging agents in multimodal imaging and image-guided therapy.

  9. Carbon Nanotubes for Supercapacitor

    Science.gov (United States)

    2010-01-01

    As an electrical energy storage device, supercapacitor finds attractive applications in consumer electronic products and alternative power source due to its higher energy density, fast discharge/charge time, low level of heating, safety, long-term operation stability, and no disposable parts. This work reviews the recent development of supercapacitor based on carbon nanotubes (CNTs) and their composites. The purpose is to give a comprehensive understanding of the advantages and disadvantages of carbon nanotubes-related supercapacitor materials and to find ways for the improvement in the performance of supercapacitor. We first discussed the effects of physical and chemical properties of pure carbon nanotubes, including size, purity, defect, shape, functionalization, and annealing, on the supercapacitance. The composites, including CNTs/oxide and CNTs/polymer, were further discussed to enhance the supercapacitance and keep the stability of the supercapacitor by optimally engineering the composition, particle size, and coverage. PMID:20672061

  10. Carbon Nanotubes for Supercapacitor

    Directory of Open Access Journals (Sweden)

    Li Jianyi

    2010-01-01

    Full Text Available Abstract As an electrical energy storage device, supercapacitor finds attractive applications in consumer electronic products and alternative power source due to its higher energy density, fast discharge/charge time, low level of heating, safety, long-term operation stability, and no disposable parts. This work reviews the recent development of supercapacitor based on carbon nanotubes (CNTs and their composites. The purpose is to give a comprehensive understanding of the advantages and disadvantages of carbon nanotubes-related supercapacitor materials and to find ways for the improvement in the performance of supercapacitor. We first discussed the effects of physical and chemical properties of pure carbon nanotubes, including size, purity, defect, shape, functionalization, and annealing, on the supercapacitance. The composites, including CNTs/oxide and CNTs/polymer, were further discussed to enhance the supercapacitance and keep the stability of the supercapacitor by optimally engineering the composition, particle size, and coverage.

  11. Carbon nanotubes for supercapacitor.

    Science.gov (United States)

    Pan, Hui; Li, Jianyi; Feng, Yuanping

    2010-01-05

    As an electrical energy storage device, supercapacitor finds attractive applications in consumer electronic products and alternative power source due to its higher energy density, fast discharge/charge time, low level of heating, safety, long-term operation stability, and no disposable parts. This work reviews the recent development of supercapacitor based on carbon nanotubes (CNTs) and their composites. The purpose is to give a comprehensive understanding of the advantages and disadvantages of carbon nanotubes-related supercapacitor materials and to find ways for the improvement in the performance of supercapacitor. We first discussed the effects of physical and chemical properties of pure carbon nanotubes, including size, purity, defect, shape, functionalization, and annealing, on the supercapacitance. The composites, including CNTs/oxide and CNTs/polymer, were further discussed to enhance the supercapacitance and keep the stability of the supercapacitor by optimally engineering the composition, particle size, and coverage.

  12. Synthesis of Co-Electrospun Lead Selenide Nanostructures within Anatase Titania Nanotubes for Advanced Photovoltaics

    Directory of Open Access Journals (Sweden)

    Evan K. Wujcik

    2015-06-01

    Full Text Available Inorganic nano-scale heterostructures have many advantages over hybrid organic-inorganic dye-sensitized solar cells (DSSC or Grätzel cells, including their resistance to photo-bleaching, thermal stability, large specific surface areas, and general robustness. This study presents a first-of-its-kind low-cost all-inorganic lead selenide-anatase titania (PbSe/TiO2 nanotube heterostructure material for photovoltaic applications. Herein, PbSe nanostructures have been co-electrospun within a hollow TiO2 nanotube with high connectivity for highly efficient charge carrier flow and electron-hole pair separation. This material has been characterized by transmission electron microscopy (TEM, electron diffraction, energy dispersive X-ray spectroscopy (EDX to show the morphology and material composition of the synthesized nanocomposite. Photovoltaic characterization has shown this newly synthesized proof-of-concept material can easily produce a photocurrent under solar illumination, and, with further refinement, could reveal a new direction in photovoltaic materials.

  13. Generation of air lasing at extended distances by coaxial dual-color femtosecond laser pulses

    Science.gov (United States)

    Li, Helong; Zang, Hongwei; Su, Yue; Fu, Yao; Xu, Huailiang

    2017-12-01

    We present an approach for generation of air lasing at extended distances by coaxial dual-color femtosecond laser pulses. A strong 800 nm pulse prepares the population inversion in {{{N}}}2+ during the filamentation in air, and a weak 400 nm pulse produced coaxially with the 800 nm light by frequency doubling in a BBO crystal seeds the {{{N}}}2+ gain medium, producing strong narrow-band lasing emission at ∼391 nm. We demonstrate that this scheme can overcome the difficulty in spatially overlapping two beams at a far distance, and the lasing emissions at a designed position can be manipulated by dispersion components inserted in the propagation path of the coaxial two-color beam. Our results provide a way for remote generation of air laser for standoff spectroscopy and detection.

  14. A Numerical Study on Heat Transfer and Flow Characteristics of a Finned Downhole Coaxial Heat Exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chun Dong; Lee, Dong Hyun; Park, Byung-Sik; Choi, Jaejoon [Korea Institute of Energy Research (KIER), Daejeon (Korea, Republic of)

    2017-02-15

    In this study, the flow and heat transfer characteristics of the finned annular passage were investigated numerically. The annular passage simulates co-axial geothermal heat exchanger, and fins are installed on its inner wall to reduce heat loss from the production passage (annulus) to injection passage (inner pipe). A commercial CFD program, Ansys Fluent, was used with SST k-ω turbulence model. The effects of the geometric parameters of the fin on the inner tube were analyzed under the periodic boundary condition. The result indicated that most parameters had a tendency to increase with an increase in the height and angle of the fin. However, it was confirmed that the Nusselt number of the inner tube on the coaxial 15, 5, 0.3 was lower than that of the smooth tube. Additionally, the Nusselt number of the inner tube exhibited a tendency of decreasing with a decrease in the spacing in Coaxial 15, S{sub f}, 0.3.

  15. Stimuli-Responsive Self-Immolative Polymer Nanofiber Membranes Formed by Coaxial Electrospinning.

    Science.gov (United States)

    Han, Daewoo; Yu, Xinjun; Chai, Qinyuan; Ayres, Neil; Steckl, Andrew J

    2017-04-05

    The first self-immolative polymer (SIP) nanofiber membrane is demonstrated in this report, in which the immolation can be triggered by external stimulus. Electrospun SIP/polyacrylonitrile (PAN) fibers provide depolymerization that is ∼25 times quicker and more responsive (i.e., immolation) than that of a cast film in the triggering condition. Depolymerization of SIP in the SIP/PAN blended fiber membrane results in the transition of the surface properties from hydrophobic (∼110°) to hygroscopic (∼0°). Triggered release of encapsulated functional molecules was demonstrated using coaxially electrospun fiber membrane made of a SIP/PAN blend sheath and polyvinylpyrrolidone/dye core. Coaxial fibers with the SIP/PAN sheath provide minimal release of the encapsulated material in nontriggering solution, while it releases the encapsulated material instantly when the triggering condition is met. Its versatility has been strengthened compared to that of non-SIP coaxial fibers that provide no triggering reaction by external stimulus.

  16. Clinical observation of micro-coaxial phacoemulsification for axial high myopia with cataract

    Directory of Open Access Journals (Sweden)

    Rui-Fan Zhang

    2014-11-01

    Full Text Available AIM: To observe the clinical effect of micro-coaxial phacoemulsification combined with intraocular lens implantation in axial high myopia with cataract.METHODS: Fifty-three patients(74 eyeswith axial high myopia and cataract underwent micro-coaxial phacoemulsification combined with intraocular lens implantation between April 2013 and December 2013. The best corrected visual acuity(BCVAwas observed at 1 and 3mo after operation, and the complications were recorded.RESULTS: Compared with the preoperative, BCVA was improved at 1 and 3mo after operation, and the differences were statistically significant(PP>0.05. There was no incidence of complications, such as retinal detachment, iris damage, pupil deformation, cystoid macular edema, endophthalmitis after operation in all patients.CONCLUSION:Micro-coaxial phacoemulsification combined with intraocular lens implantation is an effective and safe method for axial high myopia with cataract.

  17. Collapsed polymer-directed synthesis of multicomponent coaxial-like nanostructures

    KAUST Repository

    Huang, Zhiqi

    2016-07-19

    Multicomponent colloidal nanostructures (MCNs) exhibit intriguing topologically dependent chemical and physical properties. However, there remain significant challenges in the synthesis of MCNs with high-order complexity. Here we show the development of a general yet scalable approach for the rational design and synthesis of MCNs with unique coaxial-like construction. The site-preferential growth in this synthesis relies on the selective protection of seed nanoparticle surfaces with locally defined domains of collapsed polymers. By using this approach, we produce a gallery of coaxial-like MCNs comprising a shaped Au core surrounded by a tubular metal or metal oxide shell. This synthesis is robust and not prone to variations in kinetic factors of the synthetic process. The essential role of collapsed polymers in achieving anisotropic growth makes our approach fundamentally distinct from others. We further demonstrate that this coaxial-like construction can lead to excellent photocatalytic performance over conventional core–shell-type MCNs.

  18. Organic heterostructures based on arylenevinylene oligomers deposited by MAPLE

    Science.gov (United States)

    Socol, M.; Preda, N.; Vacareanu, L.; Grigoras, M.; Socol, G.; Mihailescu, I. N.; Stanculescu, F.; Jelinek, M.; Stanculescu, A.; Stoicanescu, M.

    2014-05-01

    Organic heterostructures were fabricated by matrix assisted pulsed laser evaporation (MAPLE) method using arylenevinylene oligomers based on triphenylamine (P78)/carbazole (P13) group and tris(8-hydroxyquinolinato)aluminum salt (Alq3). Optical properties of the organic multilayer structures were characterized by spectroscopic techniques: FTIR, UV-vis and photoluminescence (PL). A good transparency (over 60%) was remarked for the structures with two organic layers in the 550-800 nm range. Photoluminescence (PL) spectra proved that the emission characteristics of the materials have been preserved. I-V characteristics of (ITO/oligomer/Alq3/Al and ITO/Alq3/Al) heterostructures were symmetrically while rectifying properties of these heterostructures have not been observed. A comparison between the heterostructures made of layers with different thickness reveals that the higher current (8 × 10-6 A at 1 V) was obtained for the ITO/P78/Alq3/Al heterostructure, which is characterized by a larger thickness of the double organic layer. AFM measurements revealed a similar topography while RMS values of the reported structures depend on the organic material.

  19. Multipactor in a Coaxial Line Under the Presence of an Axial DC Magnetic Field

    CERN Document Server

    González-Iglesias, D; Anza, S; Vague, J; Gimeno, B; Boria, V E; Raboso, D; Vicente, C; Gil, J; Caspers, F; Conde, L

    2012-01-01

    The main goal of this letter is the analysis of the multipactor effect within a coaxial waveguide structure when an external axial dc magnetic field is applied. We have designed and manufactured a coaxial waveguide sample that has been immersed within a long solenoid. Numerical and experimental results confirm a significant change in the RF breakdown behavior with regard to the case without the axial dc magnetic field, as well as the existence of single- and double-surface multipactor regimes. Good agreement between theory and experimental data has been found.

  20. Simulation of Optical Funneling in Coaxial Y junctions in a Photonic Crystal

    Science.gov (United States)

    Rajaram, G.; Yashaswini, V.

    2011-07-01

    Two coaxial Y junctions in Photonic crystal (PhC) were considered for simulation of optical transmission. This coaxial Y junctions forms a funnel shaped structure. An electromagnetic beam of wavelength 1 μm was launched simultaneously at the input ports. The beam was found to propagate and get collected at the output port i.e. electromagnetic waves were found to be getting funneled from a larger area of 20 μm to an area of 4 μm. However, when the width of the defect was decreased, instead of funneling, the beams were found to undergo reflection.

  1. A novel technique for tuning of co-axial cavity of multi-beam klystron

    Energy Technology Data Exchange (ETDEWEB)

    Saha, Sukalyan, E-mail: sstechno18@gmail.com; Bandyopadhyay, Ayan Kumar; Pal, Debashis; Kant, Deepender; Joshi, Lalit Mohan; Kumar, Bijendra; Meena, Rakesh; Rawat, Vikram [Microwave Tubes Division, CSIR-CEERI, Pilani, Rajasthan-333031 (India)

    2016-03-09

    Multi-beam Klystrons (MBKs) have gained wide acceptances in the research sector for its inherent advantages. But developing a robust tuning technique for an MBK cavity of coaxial type has still remained a challenge as these designs are very prone to suffer from asymmetric field distribution with inductive tuning of the cavity. Such asymmetry leads to inhomogeneous beam-wave interaction, an undesirable phenomenon. Described herein is a new type of coaxial cavity that has the ability to suppress the asymmetry, thereby allowing tuning of the cavity with a single tuning post.

  2. Turbulence coefficients and stability studies for the coaxial flow or dissimiliar fluids. [gaseous core nuclear reactors

    Science.gov (United States)

    Weinstein, H.; Lavan, Z.

    1975-01-01

    Analytical investigations of fluid dynamics problems of relevance to the gaseous core nuclear reactor program are presented. The vortex type flow which appears in the nuclear light bulb concept is analyzed along with the fluid flow in the fuel inlet region for the coaxial flow gaseous core nuclear reactor concept. The development of numerical methods for the solution of the Navier-Stokes equations for appropriate geometries is extended to the case of rotating flows and almost completes the gas core program requirements in this area. The investigations demonstrate that the conceptual design of the coaxial flow reactor needs further development.

  3. Analysis and Design Optimization of a Coaxial Surface-Mounted Permanent-Magnet Magnetic Gear

    DEFF Research Database (Denmark)

    Zhang, Xiaoxu; Liu, Xiao; Wang, Chao

    2014-01-01

    This paper presents the analysis and design optimization of a coaxial surface-mounted permanent-magnet magnetic gear. The magnetic field distribution in the coaxial magnetic gear is calculated analytically in the polar coordinate system and then validated by the finite element method (FEM......) algorithm is employed to optimize the studied magnetic gear. Given that the torque capability and material cost conflict with each other, both of them are set as the optimization objectives in this paper. Different weight factors may be chosen for the two objectives so that more attention can be placed...

  4. Graphene/Si-nanowire heterostructure molecular sensors.

    Science.gov (United States)

    Kim, Jungkil; Oh, Si Duk; Kim, Ju Hwan; Shin, Dong Hee; Kim, Sung; Choi, Suk-Ho

    2014-06-20

    Wafer-scale graphene/Si-nanowire (Si-NW) array heterostructures for molecular sensing have been fabricated by vertically contacting single-layer graphene with high-density Si NWs. Graphene is grown in large scale by chemical vapour deposition and Si NWs are vertically aligned by metal-assisted chemical etching of Si wafer. Graphene plays a key role in preventing tips of vertical Si NWs from being bundled, thereby making Si NWs stand on Si wafer separately from each other under graphene, a critical structural feature for the uniform Schottky-type junction between Si NWs and graphene. The molecular sensors respond very sensitively to gas molecules by showing 37 and 1280% resistance changes within 3.5/0.15 and 12/0.15 s response/recovery times under O2 and H2 exposures in air, respectively, highest performances ever reported. These results together with the sensor responses in vacuum are discussed based on the surface-transfer doping mechanism.

  5. Proximity coupling in superconductor-graphene heterostructures.

    Science.gov (United States)

    Lee, Gil-Ho; Lee, Hu-Jong

    2018-02-16

    This review discusses the electronic properties and the prospective research directions of superconductor-graphene heterostructures. The basic electronic properties of graphene are introduced to highlight the unique possibility of combining two seemingly unrelated physics, superconductivity and relativity. We then focus on graphene-based Josephson junctions, one of the most versatile superconducting quantum devices. The various theoretical methods that have been developed to describe graphene Josephson junctions are examined, together with their advantages and limitations, followed by a discussion on the advances in device fabrication and the relevant length scales. The phase-sensitive properties and phase-particle dynamics of graphene Josephson junctions are examined to provide an understanding of the underlying mechanisms of Josephson coupling via graphene. Thereafter, microscopic transport of correlated quasiparticles produced by Andreev reflections at superconducting interfaces and their phase-coherent behaviors are discussed. Quantum phase transitions studied with graphene as an electrostatically tunable two-dimensional platform are reviewed. The interplay between proximity-induced superconductivity and the quantum-Hall phase is discussed as a possible route to study topological superconductivity and non-Abelian physics. Finally, a brief summary on the prospective future research directions is given. © 2018 IOP Publishing Ltd.

  6. Theory of unidirectional magnetoresistance in magnetic heterostructures

    Science.gov (United States)

    Zhang, Steven S.-L.; Vignale, Giovanni

    2017-09-01

    We present a general drift-diffusion theory beyond linear response to explain the unidirectional magnetoresistance (UMR) observed in recent experiments in various magnetic heterostructures. In general, such nonlinear magnetoresistance may originate from the concerted action of current-induced spin accumulation and spin asymmetry in electron mobility. As a case study, we calculate the UMR in a bilayer system consisting of a heavy-metal (HM) and a ferromagnetic metal (FM), where the spin accumulation is induced via the spin Hall effect in the bulk of the HM layer. Our previous formulation [cf. PRB 94, 140411(R) (2016)] is generalized to include the interface resistance and spin memory loss, which allows us to analyze in details their effects on the UMR. We found that the UMR turns out to be independent of the spin asymmetry of the interfacial resistance, at variance with the linear giant-magnetoresistance (GMR) effect. A linear relation between the UMR and the conductivity-spin asymmetry is revealed, which provides an alternative way to control the sign and magnitude of the UMR and hence may serve as an experimental signature of our proposed mechanism.

  7. The Toxicology of Carbon Nanotubes

    Science.gov (United States)

    Donaldson, Ken; Poland, Craig; Duffin, Rodger; Bonner, James

    2012-06-01

    1. Carbon nanotube structure, synthesis and applications C. Singh and W. Song; 2. The aerodynamic behaviour and pulmonary deposition of carbon nanotubes A. Buckley, R. Smith and R Maynard; 3. Utilising the concept of the biologically effective dose to define the particle and fibre hazards of carbon nanotubes K. Donaldson, R. Duffin, F. Murphy and C. Poland; 4. CNT, biopersistence and the fibre paradigm D. Warheit and M. DeLorme; 5. Length-dependent retention of fibres in the pleural space C. Poland, F. Murphy and K. Donaldson; 6. Experimental carcinogenicity of carbon nanotubes in the context of other fibres K. Unfried; 7. Fate and effects of carbon nanotubes following inhalation J. Ryman-Rasmussen, M. Andersen and J. Bonner; 8. Responses to pulmonary exposure to carbon nanotubes V. Castranova and R. Mercer; 9. Genotoxicity of carbon nanotubes R. Schins, C. Albrecht, K. Gerloff and D. van Berlo; 10. Carbon nanotube-cellular interactions; macrophages, epithelial and mesothelial cells V. Stone, M. Boyles, A. Kermanizadeh, J. Varet and H. Johnston; 11. Systemic health effects of carbon nanotubes following inhalation J. McDonald; 12. Dosimetry and metrology of carbon nanotubes L. Tran, L. MacCalman and R. Aitken; Index.

  8. Highly Confined Electronic and Ionic Conduction in Oxide Heterostructures

    DEFF Research Database (Denmark)

    Pryds, Nini

    2015-01-01

    The conductance confined at the interface of complex oxide heterostructures provides new opportunities to explore nanoelectronic as well as nanoionic devices. In this talk I will present our recent results both on ionic and electronic conductivity at different heterostructures systems. In the first...... unattainable for Bi2O3-based materials, is achieved[1]. These confined heterostructures provide a playground not only for new high ionic conductivity phenomena that are sufficiently stable but also uncover a large variety of possible technological perspectives. At the second part, I will discuss and show our...... recent results of high mobile samples realized by, interface confined redox reactions[2], strain induced polarization[3]and modulation doping at complex oxide interfaces. This collection of samples offers unique opportunities for a wide range of rich world of mesoscopic physics. [1] S. Sanne et al...

  9. Epitaxial growth and physical properties of Heusler/perovskite heterostructures

    Science.gov (United States)

    Kobayashi, K.; Ueda, K.; Fukatani, N.; Kawada, H.; Sakuma, K.; Asano, H.

    2013-08-01

    Multiferroic heterostructures of the ferromagnetic, half-metallic Heusler Fe2CrSi (FCS) and the ferroelectric perovskite Ba0.7Sr0.3TiO3 (BSTO) have been formed by magnetron sputtering, and their magnetic and ferroelectric properties have been investigated. FCS/BSTO bilayer structures were epitaxially grown on LaAlO3 substrates with epitaxial relationships of FCS (001)[110]//BSTO (001)[100]. Multiferroic properties with a remanent polarization of 10.6 µC/cm2 and a saturation magnetization of 417 emu/cc were observed for the FCS/BSTO heterostructures at room temperature. These results suggest that the Heusler/perovskite epitaxial heterostructure is a promising candidate for fabricating multiferroic devices.

  10. Aging and Humidity Effects of Hydrocarbon Gas Sensor Based on Carbon Nanotubes Functionalized with Metal Oxide Nanocrystals

    OpenAIRE

    Xiang, Jiaxi

    2017-01-01

    With the enhanced greenhouse effect and the increasing pollutants in the air, gas sensors applied in door or outdoors are in great demand. A hetero-structure gas sensors based on Multi-walled Carbon nanotubes (MWCNT) functionalized with metal oxide (MOX) nanoparticles are fabricated, which can be operated at room temperature with low power consumption. ZnO and TiO2 nanoparticles were deposited on MWCNT by Atomic Layer Deposition (ALD) at different temperatures from 17 ℃ to 220 ℃/225 ℃. The ch...

  11. The Johannesburg A-D circuit switch. A valve device for converting a co-axial Mapleson D into a co-axial Mapleson A system.

    Science.gov (United States)

    Manicom, A W; Schoonbee, C G

    1979-12-01

    A simple valve device is described for a co-axial tubing anaesthetic system which enables selection of the circuit characteristics of either a modified Mapleson A system for spontaneous breathing or a modified Mapleson D system for controlled ventilation. Thus, the system allows an economical fresh gas flow to be used during either controlled or spontaneous ventilation. The mode of ventilation may be changed during anaesthesia without adjusting the patient tubing or the attachment of the system to the anaesthetic machine.

  12. Interface-engineered oxygen octahedral coupling in manganite heterostructures

    Science.gov (United States)

    Huijben, M.; Koster, G.; Liao, Z. L.; Rijnders, G.

    2017-12-01

    Control of the oxygen octahedral coupling (OOC) provides a large degree of freedom to manipulate physical phenomena in complex oxide heterostructures. Recently, local tuning of the tilt angle has been found to control the magnetic anisotropy in ultrathin films of manganites and ruthenates, while symmetry control can manipulate the metal insulator transition in nickelate thin films. The required connectivity of the octahedra across the heterostructure interface enforces a geometric constraint to the 3-dimensional octahedral network in epitaxial films. Such geometric constraint will either change the tilt angle to retain the connectivity of the corner shared oxygen octahedral network or guide the formation of a specific symmetry throughout the epitaxial film. Here, we will discuss the control of OOC in manganite heterostructures by interface-engineering. OOC driven magnetic and transport anisotropies have been realized in LSMO/NGO heterostructures. Competition between the interfacial OOC and the strain further away from the interface leads to a thickness driven sharp transition of the anisotropic properties. Furthermore, octahedral relaxation leading to a change of p-d hybridization driven by interfacial OOC appears to be the strongest factor in thickness related variations of magnetic and transport properties in epitaxial LSMO films on NGO substrates. The results unequivocally link the atomic structure near the interfaces to the macroscopic properties. The strong correlation between a controllable oxygen network and the functionalities will have significant impact on both fundamental research and technological application of correlated perovskite heterostructures. By controlling the interfacial OOC, it is possible to pattern in 3 dimensions the magnetization to achieve non-collinear magnetization in both in-plane and out of plane directions, thus making the heterostructures promising for application in orthogonal spin transfer devices, spin oscillators, and low

  13. Electronic homogeneity of nanowire heterostructure Light Emitting Diodes (LEDs)

    Science.gov (United States)

    Selcu, Camelia; May, Brelon J.; Sarwar, A. T. M. Golam; Myers, Roberto C.

    In addition to low defect densities and great tunability bandgap within a single heterostructure, the possibility of growing (Al, In,_) GaN nanowire heterostructure LEDs on different substrates while maintaining their high electronic and optical properties makes them very attractive. We investigated the electronic homogeneity of the (Al, In,_) GaN nanowire ensemble by acquiring current maps at certain applied biases using conductive AFM. By taken IVs on individual nanowires, we found that different wires have different turn on voltages and that some of the nanowires degrade due to the applied bias.

  14. Electric field control of magnetism in multiferroic heterostructures.

    Science.gov (United States)

    Vaz, C A F

    2012-08-22

    We review the recent developments in the electric field control of magnetism in multiferroic heterostructures, which consist of heterogeneous materials systems where a magnetoelectric coupling is engineered between magnetic and ferroelectric components. The magnetoelectric coupling in these composite systems is interfacial in origin, and can arise from elastic strain, charge, and exchange bias interactions, with different characteristic responses and functionalities. Moreover, charge transport phenomena in multiferroic heterostructures, where both magnetic and ferroelectric order parameters are used to control charge transport, suggest new possibilities to control the conduction paths of the electron spin, with potential for device applications.

  15. Pneumothorax Complicating Coaxial and Non-coaxial CT-Guided Lung Biopsy: Comparative Analysis of Determining Risk Factors and Management of Pneumothorax in a Retrospective Review of 650 Patients

    Energy Technology Data Exchange (ETDEWEB)

    Nour-Eldin, Nour-Eldin A., E-mail: nour410@hotmail.com; Alsubhi, Mohammed, E-mail: mohammedal-subhi@yahoo.com; Emam, Ahmed, E-mail: morgan101002@hotmail.com; Lehnert, Thomas, E-mail: thomas.lehnert@kgu.de; Beeres, Martin, E-mail: beeres@gmx.net; Jacobi, Volkmar, E-mail: volkmar.jacobi@kgu.de; Gruber-Rouh, Tatjana, E-mail: tatjanagruber2004@yahoo.com; Scholtz, Jan-Erik, E-mail: janerikscholtz@gmail.com; Vogl, Thomas J., E-mail: t.vogl@em.uni-frankfurt.de; Naguib, Nagy N., E-mail: nagynnn@yahoo.com [Johan Wolfgang Goethe – University Hospital, Institute for Diagnostic and Interventional Radiology (Germany)

    2016-02-15

    PurposeTo assess the scope and determining risk factors related to the development of pneumothorax throughout CT-guided biopsy of pulmonary lesions in coaxial and non-coaxial techniques and the outcome of its management.Materials and MethodsThe study included CT-guided percutaneous lung biopsies in 650 consecutive patients (407 males, 243 females; mean age 54.6 years, SD 5.2) from November 2008 to June 2013 in a retrospective design. Patients were classified according to lung biopsy technique into coaxial group (318 lesions) and non-coaxial group (332 lesions). Exclusion criteria for biopsy were lesions <5 mm in diameter, uncorrectable coagulopathy, positive-pressure ventilation, severe respiratory compromise, pulmonary arterial hypertension, or refusal of the procedure. Risk factors related to the occurrence of pneumothorax were classified into: (a) Technical risk factors, (b) patient-related risk factors, and (c) lesion-associated risk factors. Radiological assessments were performed by two radiologists in consensus. Mann–Whitney U test and Fisher’s exact tests were used for statistical analysis. p values <0.05 were considered statistically significant.ResultsThe incidence of pneumothorax complicating CT-guided lung biopsy was less in the non-coaxial group (23.2 %, 77 out of 332) than the coaxial group (27 %, 86 out of 318). However, the difference in incidence between both groups was statistically insignificant (p = 0.14). Significant risk factors for the development of pneumothorax in both groups were emphysema (p < 0.001 in both groups), traversing a fissure with the biopsy needle (p value 0.005 in non-coaxial group and 0.001 in coaxial group), small lesion, less than 2 cm in diameter (p value of 0.02 in both groups), location of the lesion in the basal or mid sections of the lung (p = 0.003 and <0.001 in non-coaxial and coaxial groups, respectively), and increased needle track path within the lung tissue of more than 2.5 cm (p = 0.01 in both

  16. Effect of prolonged annealing on the performance of coaxial Ge gamma-ray detectors

    NARCIS (Netherlands)

    Owens, A.; Brandenburg, S.; Buis, E. -J.; Kozorezov, A. G.; Kraft, S.; Ostendorf, R. W.; Quarati, F.

    The effects of prolonged annealing at elevated temperatures have been investigated in a 53 cm(3) closed-end coaxial high purity germanium detector in the reverse electrode configuration. The detector was multiply annealed at 100 degrees C in block periods of 7 days. After each anneal cycle it was

  17. Design of Range Adaptive Wireless Power Transfer System Using Non-coaxial Coils

    Science.gov (United States)

    Yang, Dongsheng; Won, Sokhui; Hong, Huan

    2017-05-01

    Wireless Power Transfer (WPT) is a remarkable technology because of its convenience and applicability in harsh environment. Particularly, Magnetic Coupling WPT (MC-WPT) is a proper method to midrange power transfer, but the frequency splitting at over-coupling range, which is related with transfer distance, is challenge of transmission efficiency. In order to overcome this phenomenon, recently the range adaptive WPT is proposed. In this paper, we aim to the type with a set of non-coaxial driving coils, so that this may remove the connection wires from PA (Power Amplifier) to driving coil. And, when the radius of driving coil is changed, on the different gaps between driving and TX coils, coupling coefficient between these is computed in both cases of coaxial and non-coaxial configurations. In addition, the designing steps for 4-coil WPT system using non-coaxial coils are described with the example. Finally, the reliability of this topology has been proved and simulated with PSPICE.

  18. Experiments on a Coaxial Injector Under an Externally-Forced Transverse Acoustic Field (POSTPRINT)

    Science.gov (United States)

    2005-06-20

    Camano Schettini, and R. D. Woodward for providing us with their core length data in tabular form. The first author would like to thank his thesis...Marinet, M., and Camano Schettini, E. B., “The Density Field of Coaxial Jets with Large Velocity Ratio and Large Density Differences,” International

  19. A CFD Coupled Acoustics Approach for the Prediction of Coaxial Jet Noise

    Science.gov (United States)

    2003-02-01

    and Management of Gas Turbine Fleets for Extended Life and Reduced Costs [Les mecanismes vieillissants et le controle] [Symposium Partie A...a flow model for coaxial jets and extracting from these predictions the parameters required by the four source model (e.g. effective jet definition

  20. Reversal of Flux Closure States in Cobalt Nanoparticle Rings With Coaxial Magnetic Pulses

    DEFF Research Database (Denmark)

    Kasama, T; Dunin-Borkowski, Rafal E.; Scheinfein, MR

    2008-01-01

    Bistable flux closure (FC) states in Co nanoparticle rings can be switched reversibly by applying a coaxial magnetic field (H-z). The FC switching phenomena can be reproduced by micromagnetics simulations, which also reveal novel magnetic states at intermediate applied field strengths....

  1. 76 FR 68504 - Advisory Opinion Proceeding; Certain Coaxial Cable Connectors and Components Thereof and Products...

    Science.gov (United States)

    2011-11-04

    ... COMMISSION Advisory Opinion Proceeding; Certain Coaxial Cable Connectors and Components Thereof and Products Containing Same; Determination To Institute an Advisory Opinion Proceeding AGENCY: U.S. International Trade... determined to institute an advisory opinion proceeding in the above-captioned investigation. FOR FURTHER...

  2. A Method For Modeling Discontinuities In A Microwave Coaxial Transmission Line

    Science.gov (United States)

    Otoshi, Tom Y.

    1994-01-01

    A methodology for modeling discountinuities in a coaxial transmission line is presented. The method uses a none-linear least squares fit program to optimize the fit between a theoretical model and experimental data. When the method was applied for modeling discontinuites in a damaged S-band antenna cable, excellent agreement was obtained.

  3. Application Feasibility Evaluation on a Co-axial Piping for Intermediate Heat Transport System

    Energy Technology Data Exchange (ETDEWEB)

    Park, Chang Gyu; Kim, Jong Bum; Lee, Jae Han

    2008-02-15

    The IHX in a pool-type SFR system transfers heat from the primary high temperature sodium to the intermediate cold temperature sodium. The upper internal structure of IHX is a co-axial piping to form the flow path of both the secondary high temperature and low temperature sodium. The co-axial piping of the IHX consists of a central downcomer and riser for incoming and outgoing intermediate sodium, respectively. The IHXs of a pool-type SFR are supported at the top surface of the reactor head which is low temperature condition relatively. Therefore, the temperature distribution of a co-axial piping including the IHX support structure may induce the complicated severe thermal stress distribution. In this study, the structural features of a co-axial piping are investigated and the advanced conceptual design to accommodate the IHTS piping expansion and the severe thermal stress is proposed. It is shown through the structural analysis that the advanced design concept is effective to reduce the thermal stress and the preliminary structural integrity by considering the refuel cycle is assured.

  4. 77 FR 8898 - Certain Coaxial Cable Connectors and Components Thereof and Products Containing Same; Notice of...

    Science.gov (United States)

    2012-02-15

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Certain Coaxial Cable Connectors and Components Thereof and Products Containing Same; Notice of... thereof and products containing the same by reason of infringement of various patents, including U.S...

  5. Fibrous scaffolds loaded with protein prepared by blend or coaxial electrospinning.

    NARCIS (Netherlands)

    Ji, W.; Yang, F.; Beucken, J.J.J.P. van den; Bian, Z.; Fan, M.; Chen, Z.; Jansen, J.A.

    2010-01-01

    The aim of the present study was to fabricate polycaprolactone-based nanofibrous scaffolds with incorporated protein via either the blend or coaxial electrospinning technique. Both techniques were compared with respect to processing set-up and scaffold characteristics as well as the release kinetics

  6. Coaxial Slow Source. Final technical report, November 16, 1991--November 15, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, R.D.; Jarboe, T.R.

    1993-12-31

    This report describes work performed by the University of Washington Aerospace and Energetics Research Program involving the Field Reversed Configuration (FRC) approach to magnetic confinement fusion. The group`s effort involved continued research on the Coaxial Slow Source annular FRC experimental device located on campus, as well as support for the Large s Experiment (LSX) operated by Spectra Technology Incorporated, Bellevue, Washington.

  7. Improved theory of time domain reflectometry with variable coaxial cable length for electrical conductivity measurements

    Science.gov (United States)

    Although empirical models have been developed previously, a mechanistic model is needed for estimating electrical conductivity (EC) using time domain reflectometry (TDR) with variable lengths of coaxial cable. The goals of this study are to: (1) derive a mechanistic model based on multisection tra...

  8. Spectral line competition in a coaxial e-beam pumped high pressure Ar/Xe laser

    NARCIS (Netherlands)

    Lan, Y.F.; Lan, Y.F.; Peters, P.J.M.; Witteman, W.J.

    1991-01-01

    In order to study the kinetic mechanism of the e-beam pumped Ar/Xe laser, the temporal profiles of individual laser lines during multiline oscillation have been measured as a function of power deposition (1–12MW/cm3) and gas laser pressure (2–14 bar) using a short pulse (30 ns) coaxial electron beam

  9. Mixing Characteristics of Coaxial Injectors at High Gas to Liquid Momentum Ratios

    Science.gov (United States)

    Strakey, P. A.; Talley, D. G.; Hutt, J. J.

    1999-01-01

    A study of the spray of a swirl coaxial gas-liquid injector operating at high gas to liquid momentum ratios is reported. Mixing and droplet size characteristics of the swirl injector are also compared to a shear coaxial injector, currently being used in the Space Shuttle Main Engine fuel preburner. The injectors were tested at elevated chamber pressures using water as a LOX simulant and nitrogen and helium as gaseous hydrogen simulants. The elevated chamber pressure allowed for matching of several of the preburner injector conditions including; gas to liquid momentum ratio, density ratio and Mach number. Diagnostic techniques used to characterize the spray included; strobe back-light imaging, laser sheet spray imaging, mechanical patternation, and a phase Doppler interferometry. Results thus far indicate that the radial spreading of the swirl coaxial spray is much less than was reported in previous studies of swirl injectors operating at atmospheric back-pressure. The swirl coaxial spray does, however, exhibit a smaller overall droplet size which may be interpreted as an increase in local mixing.

  10. Photoignition Torch Applied to Cryogenic H2/O2 Coaxial Jet

    Science.gov (United States)

    2016-12-06

    19b. TELEPHONE NUMBER (Include area code ) 12/06/2016 Conference Paper 17 October 2016- 09 December 2016 Photoignition Torch Applied to Cryogenic H2/O2...Coaxial Jet A. Badakhshan, S. Danczyk, and D. Talley Air Force Research Laboratory (AFMC) AFRL/RQRC 10 E. Saturn Blvd. Edwards AFB, CA 93524-7680

  11. Electron configuration of carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Stojkovic, S.M.; Setrajcic, J.P. [Novi Sad Univ. (Yugoslavia). Inst. of Physics; Vragovic, I.D. [Technical Faculty M. Pupin, Zrenjanin (Yugoslavia)

    2000-07-01

    In the paper the analysis of electron band structure of infinite carbon nanotubes was performed using Green's function method. The electron dispersion law was found in harmonic and nearest neighbor approximation. One can see that carbon nanotubes of infinite length can be divided into two classes: metallic and semiconducting. Additional spatial confinement of the system along the nanotube axes leads to the opening of the forbidden gap even in nanotubes that are metallic for infinite length. The value of the forbidden gap decreases by increasing the tube length. The dependence of the forbidden gap on the tube length is not monotonic; it has oscillatory character for short tubes. (orig.)

  12. Fabricating Copper Nanotubes by Electrodeposition

    Science.gov (United States)

    Yang, E. H.; Ramsey, Christopher; Bae, Youngsam; Choi, Daniel

    2009-01-01

    Copper tubes having diameters between about 100 and about 200 nm have been fabricated by electrodeposition of copper into the pores of alumina nanopore membranes. Copper nanotubes are under consideration as alternatives to copper nanorods and nanowires for applications involving thermal and/or electrical contacts, wherein the greater specific areas of nanotubes could afford lower effective thermal and/or electrical resistivities. Heretofore, copper nanorods and nanowires have been fabricated by a combination of electrodeposition and a conventional expensive lithographic process. The present electrodeposition-based process for fabricating copper nanotubes costs less and enables production of copper nanotubes at greater rate.

  13. Carbon nanotube IR detectors (SV)

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, F. L.

    2012-03-01

    Sandia National Laboratories (Sandia) and Lockheed Martin Corporation (LMC) collaborated to (1) evaluate the potential of carbon nanotubes as channels in infrared (IR) photodetectors; (2) assemble and characterize carbon nanotube electronic devices and measure the photocurrent generated when exposed to infrared light;(3) compare the performance of the carbon nanotube devices with that of traditional devices; and (4) develop and numerically implement models of electronic transport and opto-electronic behavior of carbon nanotube infrared detectors. This work established a new paradigm for photodetectors.

  14. Carbon Nanotubes for Space Applications

    Science.gov (United States)

    Meyyappan, Meyya

    2000-01-01

    The potential of nanotube technology for NASA missions is significant and is properly recognized by NASA management. Ames has done much pioneering research in the last five years on carbon nanotube growth, characterization, atomic force microscopy, sensor development and computational nanotechnology. NASA Johnson Space Center has focused on laser ablation production of nanotubes and composites development. These in-house efforts, along with strategic collaboration with academia and industry, are geared towards meeting the agency's mission requirements. This viewgraph presentation (including an explanation for each slide) outlines the research focus for Ames nanotechnology, including details on carbon nanotubes' properties, applications, and synthesis.

  15. Hydraulic modeling of the flows with counter-rotating coaxial layers

    Directory of Open Access Journals (Sweden)

    Zuykov Andrey L'vovich

    2014-07-01

    Full Text Available The article is devoted to hydraulic modeling of flows with counter-rotating coaxial layers. Dynamic similarity criteria of such flows were found by the inspection analysis of the Reynolds equations. It was found that the hydrodynamic similarity criteria for physical modeling of unsteady turbulent circular-longitudinal flows with counter-rotating coaxial layers of viscous incompressible fluid are: Strouhal number - the ratio of forces of local and convective inertia, Rossby number characterizes the ratio of the azimuthal and axial velocity, Froude number - the ratio of forces of convective inertia to the forces of gravity, Euler number - the ratio of pressure forces to the convective forces of inertia, Weber number - the ratio of the convective inertia forces to surface tension forces, Reynolds number - the ratio of the convective inertia forces to the forces of molecular viscosity, Karman number - the ratio of dispersion velocity vector of fluid particles to the flow velocity. The limit value of the Reynolds number was found at the lower boundary conditions of automodel zone of such flow. It is shown that Weber and Rossby criteria for physical modeling of such flows are not determinative. It was found out that turbulent circular-longitudinal flow with counter-rotating coaxial layers are not modeled using Karman criterion. In this connection, there is a need to conduct experimental methodological research of turbulent flows with counter-rotating coaxial layers on stands equipped means of three-dimensional laser Doppler anemometry. Integral criteria of dynamic similarity of circular-longitudinal flows was considered - Heeger-Baer number (swirl number and Abramovich number, characterizing the ratio of the angular momentum and momentum of such flows. In comparison with the swirl number, Heeger-Baer number is more preferable. Abramovich number is equal to the geometric characteristics of the local swirler as similarity criterion of circular

  16. Optimal Aerodynamic Design of Conventional and Coaxial Helicopter Rotors in Hover and Forward Flight

    Science.gov (United States)

    Giovanetti, Eli B.

    This dissertation investigates the optimal aerodynamic performance and design of conventional and coaxial helicopters in hover and forward flight using conventional and higher harmonic blade pitch control. First, we describe a method for determining the blade geometry, azimuthal blade pitch inputs, optimal shaft angle (rotor angle of attack), and division of propulsive and lifting forces among the components that minimize the total power for a given forward flight condition. The optimal design problem is cast as a variational statement that is discretized using a vortex lattice wake to model inviscid forces, combined with two-dimensional drag polars to model profile losses. The resulting nonlinear constrained optimization problem is solved via Newton iteration. We investigate the optimal design of a compound vehicle in forward flight comprised of a coaxial rotor system, a propeller, and optionally, a fixed wing. We show that higher harmonic control substantially reduces required power, and that both rotor and propeller efficiencies play an important role in determining the optimal shaft angle, which in turn affects the optimal design of each component. Second, we present a variational approach for determining the optimal (minimum power) torque-balanced coaxial hovering rotor using Blade Element Momentum Theory including swirl. We show that the optimal hovering coaxial rotor generates only a small percentage of its total thrust on the portion of the lower rotor operating in the upper rotor's contracted wake, resulting in an optimal design with very different upper and lower rotor twist and chord distributions. We also show that the swirl component of induced velocity has a relatively small effect on rotor performance at the disk loadings typical of helicopter rotors. Third, we describe a more refined model of the wake of a hovering conventional or coaxial rotor. We approximate the rotor or coaxial rotors as actuator disks (though not necessarily uniformly loaded

  17. Double Coaxial Microcatheter Technique for Glue Embolization of Renal Arteriovenous Malformations

    Energy Technology Data Exchange (ETDEWEB)

    Uchikawa, Yoko, E-mail: jauchikawa@gmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Mori, Kensaku, E-mail: moriken@md.tsukuba.ac.jp [University of Tsukuba, Department of Radiology, Faculty of Medicine (Japan); Shiigai, Masanari, E-mail: m-41gai@yahoo.co.jp [Tsukuba Medical Center Hospital, Department of Radiology (Japan); Konishi, Takahiro, E-mail: soratobukangaruu@gmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Hoshiai, Sodai, E-mail: hoshiai@sb4.so-net.ne.jp [Ibaraki Prefectural Central Hospital, Department of Radiology (Japan); Ishigro, Toshitaka, E-mail: suzutokei@gmail.com; Hiyama, Takashi, E-mail: med-tak@hotmail.com [University of Tsukuba Hospital, Department of Radiology (Japan); Nakai, Yasunobu, E-mail: nakaiya@tmch.or.jp [Tsukuba Medical Center Hospital, Department of Neurosurgery (Japan); Minami, Manabu, E-mail: mminami@md.tsukuba.ac.jp [University of Tsukuba, Department of Radiology, Faculty of Medicine (Japan)

    2015-10-15

    PurposeTo demonstrate the technical benefit of the double coaxial microcatheter technique for embolization of renal arteriovenous malformations (AVMs) with n-butyl cyanoacrylate and iodized oil (glue).Materials and MethodsSix consecutive patients (1 man and 5 women; mean age 61 years; range 44–77 years) with renal AVMs were included. Five patients had hematuria, and one had a risk of heart failure due to a large intrarenal arteriovenous shunt. All patients underwent transarterial embolization using glue and the double coaxial microcatheter technique with outer 2.6F and inner 1.9F microcatheters. After glue injection, the inner microcatheter was retracted, while the outer microcatheter was retained. We assessed the complications and clinical outcomes of this technique.ResultsTechnical success was achieved in all patients. In 9 sessions, 34 feeding arteries were embolized with glue using the double coaxial microcatheter technique, 1 was embolized with glue using a single microcatheter, and 2 were embolized with coils. The double coaxial microcatheter technique was useful for selecting small tortuous feeding arteries, preventing glue reflux to the proximal arteries, and approaching multiple feeding arteries without complete retraction of the microcatheters. As a minor complication, glue migrated into the venous system in four patients without any sequelae. In all patients, favorable clinical outcomes, including hematuria cessation in five patients and improvement of the large intrarenal arteriovenous shunt in one patient, were obtained without deterioration of renal function.ConclusionGlue embolization with the double coaxial microcatheter technique was useful for treating renal AVMs with multiple tortuous feeding arteries.

  18. Development of GOX/Hydrocarbon Multi-Element Swirl Coaxial Injector Technology

    Science.gov (United States)

    Johnson, C. W.; Muss, J.; Cheng, G. C.; Davis, R.; Cohn, R. K.

    2002-11-01

    In developing the advanced liquid rocket engine, injector design is critical to obtaining the dual goals of long engine life as well as providing high-energy release efficiency in the main combustion chamber. Introducing a swirl component in the injector flow can enhance the propellant mixing and thus improve engine performance. Therefore, swirl coaxial injectors, which swirl liquid fuel around a gaseous oxygen core, show promise for the next generation of high performance staged combustion rocket engines utilizing hydrocarbon fuels. Understanding the mixing and combustion characteristics of the swirl coaxial flow provides the insight of optimizing the injector design. A joint effort of Sierra Engineering (Sierra) and the Propulsion Directorate of the Air Force Research Lab (AFRL) was conducted to develop a design methodology, utilizing both high-pressure cold-flow testing and uni-element hot-fire testing, to create a high performing, long life swirl coaxial injector for multi-element combustor use. Several swirl coax injector configurations designed and fabricated by Sierra have been tested at AFRL. The cold-flow tests and numerical simulations have been conducted. The cold flow result provided valuable information of flow characteristics of swirl coaxial injectors. However, there are two important flow features of liquid rocket engines missed from the cold flow test: (1) the effect of combustion on the propellant mixing, and (2) the interaction of multiple injectors. The present work studies the hot flow environment specifically the multiple element swirl coaxial injector. Numerical simulations were performed with a pressure-based computational fluid dynamics (CFD) code, FDNS. CFD results produced loading environments for an ANSYS finite element thermal/structural model. Since the fuels are injected at temperature below its critical temperature, the effect of phase change and chemical reactions needs to be accounted for in the CFD model.

  19. A Randomised Clinical Trial to Compare Coaxial and Noncoaxial Techniques in Percutaneous Core Needle Biopsy of Renal Parenchyma

    Energy Technology Data Exchange (ETDEWEB)

    Babaei Jandaghi, Ali [Guilan University of Medical Sciences, Department of Radiology, Poursina Hospital (Iran, Islamic Republic of); Lebady, Mohammadkazem; Zamani, Athar-Alsadat [Guilan University of Medical Sciences, Urology Research Center, Razi Hospital (Iran, Islamic Republic of); Heidarzadeh, Abtin [Guilan University of Medical Sciences, Department of Community Medicine (Iran, Islamic Republic of); Monfared, Ali [Guilan University of Medical Sciences, Urology Research Center, Razi Hospital (Iran, Islamic Republic of); Pourghorban, Ramin, E-mail: ramin-p2005@yahoo.com [Tehran University of Medical Sciences, Department of Radiology, Imam Khomeini Hospital Complex (Iran, Islamic Republic of)

    2017-01-15

    PurposeTo compare the coaxial and noncoaxial techniques of renal parenchymal core needle biopsy.Materials and MethodsThis is an institutional review board-approved randomised controlled trial comparing 83 patients (male, n = 49) who underwent renal parenchymal core biopsy with coaxial method and 83 patients (male, n = 40) with noncoaxial method. The rate of complications, the number of glomerular profiles, and the procedural time were evaluated in a comparison of the two methods. Correlation between the presence of renal parenchymal disease and the rate of complication was also evaluated.ResultsThe procedural time was significantly shorter in the coaxial technique (coaxial group, 5 ± 1 min; noncoaxial group, 14 ± 2 min; p < 0.001). The rates of complications for the coaxial method was significantly lower than the noncoaxial method (coaxial group, 10.8 %; noncoaxial group, 24.1 %; p = 0.025). There was no significant correlation between gender and the rate of complication. The number of glomerular profiles was significantly higher in patents who underwent renal biopsy with the coaxial method (coaxial group, 18.2 ± 9.1; noncoaxial group, 8.6 ± 5.5; p < 0.001). In the whole study population, the rate of complications was significantly higher in patients with a pathologic renal parenchyma compared to those with a normal parenchyma (19/71 vs. 10/95; p = 0.006).ConclusionsRenal parenchymal biopsy using a coaxial needle is a faster and safer method with a lower rate of complications.

  20. Tracking Ultrafast Carrier Dynamics in Single Semiconductor Nanowire Heterostructures

    Directory of Open Access Journals (Sweden)

    Taylor A.J.

    2013-03-01

    Full Text Available An understanding of non-equilibrium carrier dynamics in silicon (Si nanowires (NWs and NW heterostructures is very important due to their many nanophotonic and nanoelectronics applications. Here, we describe the first measurements of ultrafast carrier dynamics and diffusion in single heterostructured Si nanowires, obtained using ultrafast optical microscopy. By isolating individual nanowires, we avoid complications resulting from the broad size and alignment distribution in nanowire ensembles, allowing us to directly probe ultrafast carrier dynamics in these quasi-one-dimensional systems. Spatially-resolved pump-probe spectroscopy demonstrates the influence of surface-mediated mechanisms on carrier dynamics in a single NW, while polarization-resolved femtosecond pump-probe spectroscopy reveals a clear anisotropy in carrier lifetimes measured parallel and perpendicular to the NW axis, due to density-dependent Auger recombination. Furthermore, separating the pump and probe spots along the NW axis enabled us to track space and time dependent carrier diffusion in radial and axial NW heterostructures. These results enable us to reveal the influence of radial and axial interfaces on carrier dynamics and charge transport in these quasi-one-dimensional nanosystems, which can then be used to tailor carrier relaxation in a single nanowire heterostructure for a given application.

  1. Exciton diffusion and dissociation in conjugated polymer/fullerene heterostructures

    NARCIS (Netherlands)

    Markov, D.E.; Amsterdam, E.; Blom, P.W.M.; Sieval, A.B.; Hummelen, J.C.; Heremans, PL; Muccini, M; Hofstraat, H

    2004-01-01

    Time-resolved luminescence spectroscopy has been used to investigate exciton diffusion in thin films of poly(p-phenylene vinylene) (PPV) based derivatives. Exciton density distribution upon photoexcitation in polymer/fullerene heterostructures has been modeled and exciton diffusion length values of

  2. Topological superconductivity in metal/quantum-spin-ice heterostructures

    Science.gov (United States)

    She, Jian-Huang; Kim, Choong H.; Fennie, Craig J.; Lawler, Michael J.; Kim, Eun-Ah

    2017-11-01

    We propose a strategy to achieve an unconventional superconductor in a heterostructure: use a quantum paramagnet (QPM) as a substrate for heterostructure growth of metallic films to design exotic superconductors. The proposed setup allows us to "customize" electron-electron interaction imprinted on the metallic layer. The QPM material of our choice is quantum spin ice. Assuming the metallic layer forms a single isotropic Fermi pocket, we predict its coupling to spin fluctuations in quantum spin ice will drive topological odd-parity pairing. We further present guiding principles for materializing the suitable heterostructure using ab initio calculations and describe the band structure we predict for the case of Y2Sn2-xSbxO7 grown on the (111) surface of Pr2Zr2O7. Using this microscopic information, we predict topological odd-parity superconductivity at a few Kelvin in this heterostructure, which is comparable to the Tc of the only other confirmed odd-parity superconductor Sr2RuO4.

  3. High ionic conductivity in confined bismuth oxide-based heterostructures

    DEFF Research Database (Denmark)

    Sanna, Simone; Esposito, Vincenzo; Christensen, Mogens

    2016-01-01

    Bismuth trioxide in the cubic fluorite phase (δ-Bi2O3) exhibits the highest oxygen ionic conductivity. In this study, we were able to stabilize the pure -Bi2O3 at low temperature with no addition of stabilizer but only by engineering the interface, using highly coherent heterostructures made...

  4. Photosensitive heterostructures made of sulfonamide zinc phthalocyanine and organic semiconductor

    Czech Academy of Sciences Publication Activity Database

    Lutsyk, P.; Vertsimakha, Ya.; Nešpůrek, Stanislav; Pomaz, I.

    2011-01-01

    Roč. 535, - (2011), s. 18-29 ISSN 1542-1406 Institutional research plan: CEZ:AV0Z40500505 Keywords : heterostructure * reversal of sign in photovoltage spectra * sulphonamide-substituted phthalocyanine Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.580, year: 2011

  5. The dielectric genome of van der Waals heterostructures

    DEFF Research Database (Denmark)

    Andersen, Kirsten; Latini, Simone; Thygesen, Kristian Sommer

    2015-01-01

    Vertical stacking of two-dimensional (2D) crystals, such as graphene and hexagonal boron nitride, has recently lead to a new class of materials known as van der Waals heterostructures (vdWHs) with unique and highly tunable electronic properties. Abinitio calculations should in principle provide...

  6. Excitons in van der Waals Heterostructures: A theoretical study

    DEFF Research Database (Denmark)

    Latini, Simone

    Van der Waals heterostructures (vdWHs) represent a novel and largely unexplored class of materials. Since 2013, when Geim and Grigorieva first conceived the stacking of 2D (two-dimensional) materials to create artificial layered structures with tailored properties, a number of promising (opto...

  7. High Photovoltaic Quantum Efficiency in Ultrathin van der Waals Heterostructures.

    Science.gov (United States)

    Wong, Joeson; Jariwala, Deep; Tagliabue, Giulia; Tat, Kevin; Davoyan, Artur R; Sherrott, Michelle C; Atwater, Harry A

    2017-07-25

    We report experimental measurements for ultrathin (van der Waals heterostructures exhibiting external quantum efficiencies exceeding 50% and show that these structures can achieve experimental absorbance >90%. By coupling electromagnetic simulations and experimental measurements, we show that pn WSe 2 /MoS 2 heterojunctions with vertical carrier collection can have internal photocarrier collection efficiencies exceeding 70%.

  8. Effective mechanical properties of multilayer nano-heterostructures.

    Science.gov (United States)

    Mukhopadhyay, T; Mahata, A; Adhikari, S; Zaeem, M Asle

    2017-11-17

    Two-dimensional and quasi-two-dimensional materials are important nanostructures because of their exciting electronic, optical, thermal, chemical and mechanical properties. However, a single-layer nanomaterial may not possess a particular property adequately, or multiple desired properties simultaneously. Recently a new trend has emerged to develop nano-heterostructures by assembling multiple monolayers of different nanostructures to achieve various tunable desired properties simultaneously. For example, transition metal dichalcogenides such as MoS2 show promising electronic and piezoelectric properties, but their low mechanical strength is a constraint for practical applications. This barrier can be mitigated by considering graphene-MoS2 heterostructure, as graphene possesses strong mechanical properties. We have developed efficient closed-form expressions for the equivalent elastic properties of such multi-layer hexagonal nano-hetrostructures. Based on these physics-based analytical formulae, mechanical properties are investigated for different heterostructures such as graphene-MoS2, graphene-hBN, graphene-stanene and stanene-MoS2. The proposed formulae will enable efficient characterization of mechanical properties in developing a wide range of application-specific nano-heterostructures.

  9. Inorganic nanostructure-organic polymer heterostructures useful for thermoelectric devices

    Energy Technology Data Exchange (ETDEWEB)

    See, Kevin C.; Urban, Jeffrey J.; Segalman, Rachel A.; Coates, Nelson E.; Yee, Shannon K.

    2017-11-28

    The present invention provides for an inorganic nanostructure-organic polymer heterostructure, useful as a thermoelectric composite material, comprising (a) an inorganic nanostructure, and (b) an electrically conductive organic polymer disposed on the inorganic nanostructure. Both the inorganic nanostructure and the electrically conductive organic polymer are solution-processable.

  10. Electronic structure of carbon nanotube systems measured with scanning tunneling microscopy

    Science.gov (United States)

    Hornbaker, Daniel Jay

    Carbon fullerenes are unusually structured molecules with robust mechanical and electronic properties. Their versatility is astounding; envisioned applications range from field emission displays to impregnated metal composites, battery storage media, and nanoelectronic devices. The combination of simple constituency, diverse behavior, and ease of fabrication makes these materials a cornerstone topic in current research. This thesis details scanning tunneling microscopy (STM) experiments investigating how carbon nanotube fullerenes interact with and couple to their local environment. Scanning tunneling microscopy continues to be a key method for characterizing fullerenes, particularly in regards to their electronic properties. The atomic scale nature of this technique makes it uniquely suited for observing individual molecules and determining correlations between locally measured electronic properties and the particular environment of the molecule. The primary subject of this study is single-wall carbon nanotubes (SWNTs), which were observed under various perturbative influences resulting in measurable changes in the electronic structure. Additionally, fullerene heterostructures formed by the encapsulation of C60 molecules within the hollow interiors of SWNTs were characterized for the first time with STM. These novel macromolecules (dubbed "peapods") demonstrate the potential for custom engineering the properties of fullerene materials. Measurements indicate that the properties of individual nanotubes depend sensitively on local interactions. In particular, pronounced changes in electronic behavior are observed in nanotubes exhibiting mechanical distortion, interacting with extrinsic materials (including other nanotubes), and possessing intrinsic defects in the atomic lattice. In fullerene peapods, while no discernable change in the atomic ordering of the encapsulating nanotubes was evident, the presence of interior C60 molecules has a dramatic effect on the

  11. Severe Intraoperative Hypercapnia Complicating an Unsual Malfunction of the Inner Tube of a Co-axial (BAIN'S Circuit

    Directory of Open Access Journals (Sweden)

    Youssef Emam Youssef

    2010-04-01

    Full Text Available The Bain's co-axial circuit system is fully established in general anaesthesia practice. It is favoured for its light weight and suitability for head and neck surgery. However, there are numerous published reports of malfunction of the inner tube of the Bain's co-axial circuit, with potentially lethal complications for the patient. This report presents a case in which a patient connected to a reused Bain's circuit (Datex-Ohmeda developed severe hypercapnia in the early intraoperative period due to unusual defect of the inner tube. This report tests and outlines the integrity of co-axial circuits and also reviews the available literature.

  12. Silicon Carbide Nanotube Synthesized

    Science.gov (United States)

    Lienhard, Michael A.; Larkin, David J.

    2003-01-01

    Carbon nanotubes (CNTs) have generated a great deal of scientific and commercial interest because of the countless envisioned applications that stem from their extraordinary materials properties. Included among these properties are high mechanical strength (tensile and modulus), high thermal conductivity, and electrical properties that make different forms of single-walled CNTs either conducting or semiconducting, and therefore, suitable for making ultraminiature, high-performance CNT-based electronics, sensors, and actuators. Among the limitations for CNTs is their inability to survive in high-temperature, harsh-environment applications. Silicon carbon nanotubes (SiCNTs) are being developed for their superior material properties under such conditions. For example, SiC is stable in regards to oxidation in air to temperatures exceeding 1000 C, whereas carbon-based materials are limited to 600 C. The high-temperature stability of SiCNTs is envisioned to enable high-temperature, harsh-environment nanofiber- and nanotube-reinforced ceramics. In addition, single-crystal SiC-based semiconductors are being developed for hightemperature, high-power electronics, and by analogy to CNTs with silicon semiconductors, SiCNTs with single-crystal SiC-based semiconductors may allow high-temperature harsh-environment nanoelectronics, nanosensors, and nanoactuators to be realized. Another challenge in CNT development is the difficulty of chemically modifying the tube walls, which are composed of chemically stable graphene sheets. The chemical substitution of the CNTs walls will be necessary for nanotube self-assembly and biological- and chemical-sensing applications. SiCNTs are expected to have a different multiple-bilayer wall structure, allowing the surface Si atoms to be functionalized readily with molecules that will allow SiCNTs to undergo self-assembly and be compatible with a variety of materials (for biotechnology applications and high-performance fiber-reinforced ceramics).

  13. Carbon Nanotubes for Supercapacitor

    OpenAIRE

    Li Jianyi; Pan Hui; Feng YuanPing

    2010-01-01

    Abstract As an electrical energy storage device, supercapacitor finds attractive applications in consumer electronic products and alternative power source due to its higher energy density, fast discharge/charge time, low level of heating, safety, long-term operation stability, and no disposable parts. This work reviews the recent development of supercapacitor based on carbon nanotubes (CNTs) and their composites. The purpose is to give a comprehensive understanding of the advantages and disad...

  14. 148. Carbon Nanotubes

    OpenAIRE

    Hedmer, Maria; Kåredal, Monica; Gustavsson, Per; Rissler, Jenny

    2013-01-01

    Carbon nanotubes (CNTs) can be seen as graphene sheets rolled to form cylinders. CNTs may be categorised as single- (SWCNT) or multi-walled (MWCNT). Due to the small size, the number of particles as well as the surface area per mass unit is extremely high. CNTs are highly diverse, differing with respect to e.g., diameter, length, chiral angles, chemical functionalisation, purity, stiffness and bulk density. Today, CNTs are utilised primarily for the reinforcement of composite polymers, but th...

  15. Carbon nanotube-polymer composite actuators

    Science.gov (United States)

    Gennett, Thomas [Denver, CO; Raffaelle, Ryne P [Honeoye Falls, NY; Landi, Brian J [Rochester, NY; Heben, Michael J [Denver, CO

    2008-04-22

    The present invention discloses a carbon nanotube (SWNT)-polymer composite actuator and method to make such actuator. A series of uniform composites was prepared by dispersing purified single wall nanotubes with varying weight percents into a polymer matrix, followed by solution casting. The resulting nanotube-polymer composite was then successfully used to form a nanotube polymer actuator.

  16. Elastic and piezoelectric properties of zincblende and wurtzite crystalline nanowire heterostructures.

    Science.gov (United States)

    Boxberg, Fredrik; Søndergaard, Niels; Xu, H Q

    2012-09-04

    The elastic and piezoelectric properties of zincblende and wurtzite crystalline InAs/InP nanowire heterostructures have been studied using electro-elastically coupled continuum elasticity theory. A comprehensive comparison of strains, piezoelectric potentials and piezoelectric fields in the two crystal types of nanowire heterostructures is presented. For each crystal type, three different forms of heterostructures-core-shell, axial superlattice, and quantum dot nanowire heterostructures-are considered. In the studied nanowire heterostructures, the principal strains are found to be insensitive to the change in the crystal structure. However, the shear strains in the zincblende and wurtzite nanowire heterostructures can be very different. All the studied nanowire heterostructures are found to exhibit a piezoelectric field along the nanowire axis. The piezoelectric field is in general much stronger in a wurtzite nanowire heterostructure than in its corresponding zincblende heterostructure. Our results are expected to be particularly important for analyzing and understanding the properties of epitaxially grown nanowire heterostructures and for applications in nanowire electronics, optoelectronics, and biochemical sensing. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Elastic and piezoelectric properties of zincblende and wurtzite crystalline nanowire heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Boxberg, Fredrik [Division of Solid State Physics, Lund University (Sweden); Soendergaard, Niels [Division of Mathematical Physics, Lund University (Sweden); Xu, H.Q. [Department of Electronics and Key Laboratory for the Physics and Chemistry of Nanodevices, Peking University, Beijing (China); Division of Solid State Physics, Lund University (Sweden)

    2012-09-04

    The elastic and piezoelectric properties of zincblende and wurtzite crystalline InAs/InP nanowire heterostructures have been studied using electro-elastically coupled continuum elasticity theory. A comprehensive comparison of strains, piezoelectric potentials and piezoelectric fields in the two crystal types of nanowire heterostructures is presented. For each crystal type, three different forms of heterostructures - core-shell, axial superlattice, and quantum dot nanowire heterostructures - are considered. In the studied nanowire heterostructures, the principal strains are found to be insensitive to the change in the crystal structure. However, the shear strains in the zincblende and wurtzite nanowire heterostructures can be very different. All the studied nanowire heterostructures are found to exhibit a piezoelectric field along the nanowire axis. The piezoelectric field is in general much stronger in a wurtzite nanowire heterostructure than in its corresponding zincblende heterostructure. Our results are expected to be particularly important for analyzing and understanding the properties of epitaxially grown nanowire heterostructures and for applications in nanowire electronics, optoelectronics, and biochemical sensing. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  18. Magnetic nanotubes for drug delivery

    Science.gov (United States)

    Ramasamy, Mouli; Kumar, Prashanth S.; Varadan, Vijay K.

    2017-04-01

    Magnetic nanotubes hold the potential for neuroscience applications because of their capability to deliver chemicals or biomolecules and the feasibility of controlling the orientation or movement of these magnetic nanotubes by an external magnetic field thus facilitating directed growth of neurites. Therefore, we sought to investigate the effects of laminin treated magnetic nanotubes and external alternating magnetic fields on the growth of dorsal root ganglion (DRG) neurons in cell culture. Magnetic nanotubes were synthesized by a hydrothermal method and characterized to confirm their hollow structure, the hematite and maghemite phases, and the magnetic properties. DRG neurons were cultured in the presence of magnetic nanotubes under alternating magnetic fields. Electron microscopy showed a close interaction between magnetic nanotubes and the growing neurites Phase contrast microscopy revealed live growing neurons suggesting that the combination of the presence of magnetic nanotubes and the alternating magnetic field were tolerated by DRG neurons. The synergistic effect, from both laminin treated magnetic nanotubes and the applied magnetic fields on survival, growth and electrical activity of the DRG neurons are currently being investigated.

  19. Single carbon nanotube photovoltaic device

    NARCIS (Netherlands)

    Barkelid, K.M.; Zwiller, V.G.

    2013-01-01

    Here we present photocurrent measurements on a single suspended carbon nanotube p-n junction. The p-n junction was induced by electrostatic doping by local gates, and the E11 and E22 resonances in the nanotube could be probed using photocurrent spectroscopy. Current-voltage characteristics were

  20. Doping effect of In{sub 2}O{sub 3} on structural and ethanol-sensing characteristics of ZnO nanotubes fabricated by electrospinning

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Baoyu; Zhao, Changhui; Zhang, Mingxiang; Zhang, Zemin; Xie, Erqing, E-mail: xieeq@lzu.edu.cn; Zhou, Jinyuan, E-mail: zhoujy@lzu.edu.cn; Han, Weihua

    2015-09-15

    Highlights: • IZO nanotubes with various indium contents were synthesized by electrospinning. • A well-crystallized indium-zinc-oxide solid solution formed in IZO-0.01 nanotubes. • Amorphous In{sub 2}O{sub 3} segregated at ZnO grain boundaries at high indium doping levels. • IZO-0.01 nanotubes show a high response and good selectivity to ethanol at 275 °C. - Abstract: Indium-doped ZnO (IZO) nanotubes with various indium contents (0.01–0.20) were synthesized via a facile electrospinning method. Results of X-ray diffraction and transmission electron microscopy demonstrate that all samples are consisted of hexagonal wurtzite-typed ZnO, showing a well-crystallized indium-zinc-oxide solid solution when only a small amount of zinc ions substituted by indium ions (0.01). Once the amount of indium dopants ≥0.05, there will form some amorphous In{sub 2}O{sub 3}, leading to a pronounced decrease in grain sizes. Gas-sensing performances revealed that the IZO nanotube-based sensors have enhanced ethanol-sensing characteristics, especially, sensor based on IZO-0.01 nanotubes shows the highest response (R{sub a}/R{sub g} = 81.7), which is twice that of the undoped ZnO nanotubes (40.0) toward 100 ppm ethanol at an operating temperature of 275 °C. And IZO-0.20 nanotube-based sensor presents a relatively high response at high ethanol concentrations. Our research suggested that these remarkable enhanced ethanol-sensing properties can be closely related to the formation of indium-zinc-oxide solid solutions and/or heterostructures between ZnO and amorphous In{sub 2}O{sub 3}.

  1. Theoretical properties of carbon nanotubes

    CERN Document Server

    Palser, A H

    2000-01-01

    Carbon nanotubes are invariably terminated with hemi-fullerene caps. In order to investigate the effect of these caps on the electronic structure, a method is developed to enumerate every hemi-fullerene cap which is commensurate with a given nanotube body. This algorithm is then applied to nanotubes for which I + m <= 25. The results of this algorithm are then used to study the effects of caps with different symmetries on the electronic structure of metallic and semi-conducting nanotubes within the Hueckel model. It is found that caps can cause localised and resonance states, although the likelihood of localised states occurring in capped metallic nanotubes is shown to be small. In addition, caps induce a non-uniform charge distribution, in which negative charge tends to accumulate on pentagon vertices. The thesis ends by describing two new density matrix methods for performing linear-scaling electronic-structure calculations within the independent electron approximation. Example calculations demonstrate t...

  2. Modelling Heat Transfer of Carbon Nanotubes

    OpenAIRE

    Yang, Xin-She

    2010-01-01

    Modelling heat transfer of carbon nanotubes is important for the thermal management of nanotube-based composites and nanoelectronic device. By using a finite element method for three-dimensional anisotropic heat transfer, we have simulated the heat conduction and temperature variations of a single nanotube, a nanotube array and a part of nanotube-based composite surface with heat generation. The thermal conductivity used is obtained from the upscaled value from the molecular simulations or ex...

  3. Synthesis and structural characterization of coaxial nano tubes intercalated of molybdenum disulfide with carbon; Sintesis y caracterizacion estructural de nanotubos coaxiales intercalados de disulfuro de molibdeno con carbono

    Energy Technology Data Exchange (ETDEWEB)

    Reza San German, C.M

    2005-07-01

    In this work the study of some fundamental aspects in the growth of unidimensional systems of coaxial nano tubes from the mold method is approached. This method is an inclusion technique of a precursor reagent into oxide nano porous alumina film (mold), and later applying some processes of synthesis it is gotten to obtain the wished material. The synthesized structures are identified later because they take place by means of the initial formation of nano tubes of MoS{sub 2}, enclosing to carbon nano tubes by the same method, with propylene flow which generates a graphitization process that 'copy' the mold through as it flows. Binary phase MoS{sub 2} + C nano tubes were synthesized by propylene pyrolysis inside MoS{sub 2} nano tubes prepared by template assisted technique. The large coaxial nano tubes constituted of graphite sheets inserted between the MoS{sub 2} layers forming the outer part, and coaxial multi wall carbon nano tubes (MWCNT) intercalated with MoS{sub 2} inside. High resolution electron microscopy (HRTEM), electron energy loss spectroscopy (EELS), high angle annular dark field (HAADF), gatan image filter (GIF), nano beam electron diffraction patterns (NBEDP), along with molecular dynamics simulation and quantum mechanical calculations were used to characterize the samples. The one-dimensional structures exhibit diverse morphologies such as long straight and twisted nano tubes with several structural irregularities. The inter-planar spacing between MoS{sub 2} layers was found to increase from 6.3 to 7.4 A due to intercalation with carbon. Simulated HREM images revealed the presence of these twisted nano structures, with mechanical stretch into intercalate carbon between MoS{sub 2} layers. Our results open up the possibility of using MoS{sub 2} nano tubes as templates for the synthesis of new one- dimensional binary phase systems. (Author)

  4. Secondary doping in polyaniline layers coated on multi-walled carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Zhou Yi

    2015-01-01

    Full Text Available HC1 doped coaxial polyaniline/multiwalled carbon nanotubes (MWCNTs nanocomposites were first prepared by in–situ chemical polymerization of aniline monomers in the presence of MWCNTs with less structural defects. P-toluene sulfonic acid (TSA and 5-sulfosalicylic acid dihydrate (SSA redoped PANI/MWCNT nanocomposites were achieved after the as-prepared nanocomposites were treated by ammonia respectively. The redoped nanocomposites were characterized by field emission scanning electron microscopy, transmission electron microscopy, fourier transform infrared spectroscopy, Raman, X–ray diffraction, thermogravimetric analysis and cyclic voltammetry, respectively. The results indicated that the thermal stability and electrochemical behaviour of TSA doped PANI/MWCNT nanocomposites were better than that of SSA doped PANI/MWCNT nanocomposites.

  5. Carbon Nanotubes and Modern Nanoagriculture

    KAUST Repository

    Serag, Maged F.

    2015-01-27

    Since their discovery, carbon nanotubes have been prominent members of the nanomaterial family. Owing to their extraordinary physical, chemical, and mechanical properties, carbon nanotubes have been proven to be a useful tool in the field of plant science. They were frequently perceived to bring about valuable biotechnological and agricultural applications that still remain beyond experimental realization. An increasing number of studies have demonstrated the ability of carbon nanotubes to traverse different plant cell barriers. These studies, also, assessed the toxicity and environmental impacts of these nanomaterials. The knowledge provided by these studies is of practical and fundamental importance for diverse applications including intracellular labeling and imaging, genetic transformation, and for enhancing our knowledge of plant cell biology. Although different types of nanoparticles have been found to activate physiological processes in plants, carbon nanotubes received particular interest. Following addition to germination medium, carbon nanotubes enhanced root growth and elongation of some plants such as onion, cucumber and rye-grass. They, also, modulated the expression of some genes that are essential for cell division and plant development. In addition, multi-walled carbon nanotubes were evidenced to penetrate thick seed coats, stimulate germination, and to enhance growth of young tomato seedlings. Multi-walled carbon nanotubes can penetrate deeply into the root system and further distribute into the leaves and the fruits. In recent studies, carbon nanotubes were reported to be chemically entrapped into the structure of plant tracheary elements. This should activate studies in the fields of plant defense and wood engineering. Although, all of these effects on plant physiology and plant developmental biology have not been fully understood, the valuable findings promises more research activity in the near future toward complete scientific understanding of

  6. Synthesis, characterization and photovoltaic integration of type II nanorod heterostructures

    Science.gov (United States)

    McDaniel, Hunter Y.

    Motivated by a desire to control the actions of charges within materials in new and productive ways, researchers have increasingly focused their efforts on engineering materials on the nanometer scale where the laws of quantum mechanics rule supreme. Novel properties emerge when a semiconductor crystal is prepared at sizes below the hydrogenic ground state of the material, also known as the exciton Bohr radius. In addition to effects of quantum confinement, the large fraction of surface atoms can play a significant role in determining nanocrystal properties and applications. By combining two or more nanometer scale semiconductor crystals together to form a nanocrystal heterostructure, new avenues for materials engineering are opened up as nascent properties emerge. The high fraction of surface atoms means that much larger degrees of strain are possible than in the bulk. The large fraction of interface atoms means that the heterojunction properties can dominate the properties of the entire structure. Along with engineering these novel multi component properties comes new unexplored areas of science to be investigated and understood. New techniques are needed for studying these materials that require resolution of features much smaller than the wavelength of (visible) light. Along with this research comes a responsibility to share findings with the scientific community and to pursue directions that can positively impact humanity. At the same time, we should take a long term view when judging the applications of this or any new technology as we are only beginning to understand what is possible. After an introduction to the field in chapter one where we motivate our focus on anisotropic nanocrystal heterostructures, we discuss the formation of Fe3O4/CdS structures from spherical seeds in chapter two. In chapter three we turn our focus to type II CdSe/CdTe nanorod heterostructures where the anisotropy is inherent. The type II system is of particular interest because

  7. Graphene encapsulated gold nanoparticle-quantum dot heterostructures and their electrochemical characterization

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yuan [Metallurgical and Materials Engineering Department, Center for Materials for Information Technology (MINT), The University of Alabama, Tuscaloosa, AL 35487 (United States); Chopra, Nitin, E-mail: nchopra@eng.ua.edu [Metallurgical and Materials Engineering Department, Center for Materials for Information Technology (MINT), The University of Alabama, Tuscaloosa, AL 35487 (United States); Department of Biological Sciences, The University of Alabama, Tuscaloosa, AL 35487 (United States); Department of Chemistry, The University of Alabama, Tuscaloosa, AL 35487 (United States)

    2015-07-30

    Highlights: • Patterning of multilayer graphene shell encapsulated gold nanoparticles (GNPs). • Binding of quantum dots to GNPs resulted in GNP-QD heterostructures. • The heterostructures were characterized for their electrochemical properties. - Abstract: A simple technique for patterning multilayer graphene shell encapsulated gold nanoparticles (GNPs) on the silicon substrate and their further surface decoration with semiconducting quantum dots (QDs) is reported. This leads to the fabrication of a novel silicon electrode decorated with GNP-QD hybrids or heterostructures. The morphology, structure, and composition of the GNPs and GNP-QD heterostructures were evaluated using microscopic and spectroscopic techniques. The heterostructures decorated silicon electrode was also evaluated for the electronic and electrochemical properties. The results showed that the electrical characteristics of the silicon substrate were significantly improved by decorating with GNPs and quantum dots. Furthermore, GNP-QD heterostructure electrode was observed to show significantly increased electrochemical charge transfer activity.

  8. Preparation of asiaticoside-loaded coaxially electrospinning nanofibers and their effect on deep partial-thickness burn injury.

    Science.gov (United States)

    Zhu, Lifei; Liu, Xiaoyan; Du, Lina; Jin, Yiguang

    2016-10-01

    Sodium alginate and chitosan were in favor of wound healing. However, the two polymers were not compatible in one formulation due to the electrostatic interaction. Coaxially electrospinning technology could make two or more noneletrospun polymers to be electrospun in independent core and shell layer. Asiaticoside-loaded coaxially electrospinning nanofibers of alginate, polyvinyl alcohol (PVA) and chitosan (alginate/PVA/chitosan) were prepared and evaluated. Morphologies and microstructure of nanofibers were observed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Drug release in vitro of coaxial nanofibers was also evaluated. Deep partial-thickness burn injury were established and used to evaluate the improved healing effect of asiaticoside-loaded coaxial nanofibers. Drug-loaded coaxial nanofibers prepared with the optimized formulations and technologies had the obvious core-shell structure. Coaxial nanofibers showed faster drug release profiles in vitro and this facilitated wound healing. Its healing effect on rats with deep partial-thickness burn injury was also significant based on morphology, wound healing ratio, and pathological sections. Positive expression of vascular endothelial growth factor (VEGF), cluster of differentiation 31 (CD31), and proliferating cell nuclear antigen (PCNA), and down regulation of tumor necrosis factor (TNF) and interleukin-6 (IL-6) also validated the improved effect of wound healing. In general, the asiaticoside-loaded coaxial nanofibers had obvious core-shell structure with smooth surface and uniform diameter. Its healing effect on deep partial-thickness burn injury of rats was obvious. Asiaticoside-loaded coaxial nanofibers provide a novel promising option for treatment of deep partial-thickness burn injury. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  9. Advanced Semiconductor Heterostructures Novel Devices, Potential Device Applications and Basic Properties

    CERN Document Server

    Stroscio, Michael A

    2003-01-01

    This volume provides valuable summaries on many aspects of advanced semiconductor heterostructures and highlights the great variety of semiconductor heterostructures that has emerged since their original conception. As exemplified by the chapters in this book, recent progress on advanced semiconductor heterostructures spans a truly remarkable range of scientific fields with an associated diversity of applications. Some of these applications will undoubtedly revolutionize critically important facets of modern technology. At the heart of these advances is the ability to design and control the pr

  10. Abnormal room temperature ferromagnetism in CuO-ZnO heterostructures: interface related or not?

    Science.gov (United States)

    Gao, Daqiang; Zhang, Zhipeng; Li, You; Xia, Baorui; Shi, Shoupeng; Xue, Desheng

    2015-01-21

    We report the new functionality of room temperature ferromagnetism in CuO-ZnO heterostructures. Magnetic measurement results indicate the CuO-ZnO heterostructures show enhanced ferromagnetism contrary to the pure CuO (ZnO) and the observed ferromagnetism is proportional to the interface counts for the film-heterostructures, providing proof of interface related ferromagnetism. Our study suggests that magnetically functional interfaces could be an entirely new and novel design of magnetic materials for emergent devices.

  11. Nano-scale polar-nonpolar oxide heterostructures for photocatalysis

    Science.gov (United States)

    Guo, Hongli; Saidi, Wissam A.; Yang, Jinlong; Zhao, Jin

    2016-03-01

    We proposed based on first principles density functional theory calculations that a nano-scale thin film based on a polar-nonpolar transition-metal oxide heterostructure can be used as a highly-efficient photocatalyst. This is demonstrated using a SrTiO3/LaAlO3/SrTiO3 sandwich-like heterostructure with photocatalytic activity in the near-infrared region. The effect of the polar nature of LaAlO3 is two-fold. First, the induced electrostatic field accelerates the photo-generated electrons and holes into opposite directions and minimizes their recombination rates. Hence, the reduction and oxidation reactions can be instigated at the SrTiO3 surfaces located on the opposite sides of the heterostructure. Second, the electric field reduces the band gap of the system making it photoactive in the infrared region. We also show that charge separation can be enhanced by using compressive strain engineering that creates ferroelectric instability in STO. The proposed setup is ideal for tandem oxide photocatalysts especially when combined with photoactive polar materials.We proposed based on first principles density functional theory calculations that a nano-scale thin film based on a polar-nonpolar transition-metal oxide heterostructure can be used as a highly-efficient photocatalyst. This is demonstrated using a SrTiO3/LaAlO3/SrTiO3 sandwich-like heterostructure with photocatalytic activity in the near-infrared region. The effect of the polar nature of LaAlO3 is two-fold. First, the induced electrostatic field accelerates the photo-generated electrons and holes into opposite directions and minimizes their recombination rates. Hence, the reduction and oxidation reactions can be instigated at the SrTiO3 surfaces located on the opposite sides of the heterostructure. Second, the electric field reduces the band gap of the system making it photoactive in the infrared region. We also show that charge separation can be enhanced by using compressive strain engineering that creates

  12. Wave Propagation in a coaxial waveguide with a periodic slot array

    CERN Document Server

    Alesini, D; Garganese, C; Migliorati, M; Palumbo, L

    2001-01-01

    In this paper we present the numerical and experimental study of the electromagnetic elds that propagate in a coaxial waveguide having periodic slots in the inner conductor. The aim of the work is to estimate the e ects of the holes on the phase velocity of the eld propagating in structures like the LHC liner, and to which extent these elds can be considered synchronous with the generating beam. To this end we have performed a numerical analysis by using the MAFIA simulation code, and have obtained, for a given geometry, the ampli- tude of the slowing down of the phase velocity due to the presence of the slot array. We have then performed a set of measurements of this e ect on a simple coaxial resonator, measuring the shift of the resonance frequencies produced by the slots. This shift, related to the phase velocity, has been compared with the results obtained with the simulations.

  13. Levitation force of small clearance superconductor-magnet system under non-coaxial condition

    Science.gov (United States)

    Xu, Jimin; Jin, Yingze; Yuan, Xiaoyang; Miao, Xusheng

    2017-03-01

    A novel superconducting tilting-pad bearing was proposed for the advanced research of reusable liquid hydrogen turbopump in liquid rocket. The bearing is a combination of superconducting magnetic bearing and hydrodynamic fluid-film bearing. Since the viscosity of cryogenic fuel to activate superconducting state and form hydrodynamic fluid-film is very low, bearing clearance will be very small. This study focuses on the investigation of superconducting levitation force in this kind of small clearance superconductor-magnet system. Based on Bean critical state model and three-dimensional finite element method, an analysis method is presented to obtain the levitation force under such situation. Since the complicated operational conditions and structural arrangement for application in liquid rocket, center lines of bulk superconductor and magnet rotor will usually be in non-coaxial state. Superconducting levitation forces in axial direction and radial direction under non-coaxial situation are also analyzed by the presented method.

  14. Fabrication and Photovoltaic Characteristics of Coaxial Silicon Nanowire Solar Cells Prepared by Wet Chemical Etching

    Directory of Open Access Journals (Sweden)

    Chien-Wei Liu

    2012-01-01

    Full Text Available Nanostructured solar cells with coaxial p-n junction structures have strong potential to enhance the performances of the silicon-based solar cells. This study demonstrates a radial junction silicon nanowire (RJSNW solar cell that was fabricated simply and at low cost using wet chemical etching. Experimental results reveal that the reflectance of the silicon nanowires (SNWs declines as their length increases. The excellent light trapping was mainly associated with high aspect ratio of the SNW arrays. A conversion efficiency of ∼7.1% and an external quantum efficiency of ∼64.6% at 700 nm were demonstrated. Control of etching time and diffusion conditions holds great promise for the development of future RJSNW solar cells. Improving the electrode/RJSNW contact will promote the collection of carries in coaxial core-shell SNW array solar cells.

  15. Properties of quarter-wavelength coaxial cavity for triode-type thermionic RF gun

    Science.gov (United States)

    Torgasin, Konstantin; Mishima, Kenta; Zen, Heishun; Yoshida, Kohei; Negm, Hani; Omer, Muhamed; Kii, Toshiteru; Nagasaki, Kazunobu; Masuda, Kai; Ohgaki, Hideaki

    2017-09-01

    A quarter-wavelength coaxial cavity with a longitudinal radio-frequency power supply was fabricated and tested. The cavity was designed as a pre-buncher for a thermionic triode-type radio-frequency gun of a mid-infrared free electron laser facility. The triode structure was formed to ensure the reduction of the back-bombarding effect, which usually appears in thermionic radio-frequency guns. The coaxial cavity was tested using a tungsten dispenser cathode. From the results of the cold test, a cavity voltage of about 25 kV can be attained, which corresponds to designed characteristics. In contrast, the hot test showed a sudden drop in voltage, resulting in an unstable operation. The small dimensions of the cavity caused some low-field effects, which led to multipactoring. In this paper, we report the tested characteristics of the pre-bunching cavity.

  16. Magnetic Ignition of Pulsed Gas Discharges in Air of Low Pressure in a Coaxial Plasma Gun

    Science.gov (United States)

    Thom, Karlheinz; Norwood, Joseph, Jr.

    1961-01-01

    The effect of an axial magnetic field on the breakdown voltage of a coaxial system of electrodes has been investigated by earlier workers. For low values of gas pressure times electrode spacing, the breakdown voltage is decreased by the application of the magnetic field. The electron cyclotron radius now assumes the role held by the mean free path in nonmagnetic discharges and the breakdown voltage becomes a function of the magnetic flux density. In this paper the dependence of the formative time lag as a function of the magnetic flux density is established and the feasibility of using a magnetic field for igniting high-voltage, high-current discharges is shown through theory and experiment. With a 36 microfarad capacitor bank charged to 48,000 volts, a peak current of 1.3 x 10( exp 6) amperes in a coaxial type of plasma gun was achieved with a current rise time of only 2 microseconds.

  17. A global model of cylindrical and coaxial surface-wave discharges

    Science.gov (United States)

    Kemaneci, Efe; Mitschker, Felix; Rudolph, Marcel; Szeremley, Daniel; Eremin, Denis; Awakowicz, Peter; Brinkmann, Ralf Peter

    2017-06-01

    A volume-averaged global model is developed to investigate surface-wave discharges inside either cylindrical or coaxial structures. The neutral and ion wall flux is self-consistently estimated based on a simplified analytical description both for electropositive and electronegative plasmas. The simulation results are compared with experimental data from various discharge setups of either argon or oxygen, measured or obtained from the literature over a wide range of pressure and power, for a continuous and a pulse-modulated power input. A good agreement is observed between the simulations and the measurements. The contribution of the wall flux on the net loss rates is quantified for a variety of species in different discharge setups. A coaxial plasmaline is further investigated to reveal the detailed behaviour of plasma properties with respect to input power and pressure.

  18. PMMA/PS coaxial electrospinning: core-shell fiber morphology as a function of material parameters

    Science.gov (United States)

    Rahmani, Shahrzad; Arefazar, Ahmad; Latifi, Masoud

    2017-03-01

    Core-shell fibers of polymethyl methacrylate (PMMA) and polystyrene (PS) have been successfully electrospun by coaxial electrospinning. To evaluate the influence of the solvent on the final fiber morphology, four types of organic solvents were used in the shell solution while the core solvent was preserved. Morphological observations with scanning electron microscopy, transmission electron microscopy and optical microscopy revealed that both core and shell solvent properties were involved in the final fiber morphology. To explain this involvement, alongside a discussion of the Bagley solubility graph of PS and PMMA, a novel criterion based on solvent physical properties was introduced. A theoretical model based on the momentum conservation principle was developed and applied for describing the dependence of the core and shell diameters to their solvent combinations. Different concentrations of core and shell were also investigated in the coaxial electrospinning of PMMA/PS. The core-shell fiber morphologies with different core and shell concentrations were compared with their single electrospun fibers.

  19. Dual Circularly Polarized Omnidirectional Antenna with Slot Array on Coaxial Cylinder

    Directory of Open Access Journals (Sweden)

    Bin Zhou

    2015-01-01

    Full Text Available A dual circularly polarized (CP omnidirectional antenna based on slot array in coaxial cylinder structure is presented in this paper. It is constructed by perpendicular slot pairs around and along the axis of the coaxial cylinder to realize the omnidirectional CP property, and two ports are assigned in its two sides as left hand circularly polarized (LHCP port and right hand circularly polarized (RHCP port, respectively. The proposed antenna achieves a bandwidth of 16.4% ranging from 5.05 to 5.95 GHz with an isolation higher than 15 dB between the two CP ports, and the return loss (RL is higher than 10 dB within the bandwidth in both of the two ports. From the measured results, the average axial ratio (AR of the proposed antenna in omnidirectional plane is lower than 1.5 dB.

  20. Synthesis and applications of heterostructured semiconductor nanocrystals

    Science.gov (United States)

    Khon, Elena

    Semiconductor nanocrystals (NCs) have been of great interest to researchers for several decades due to their unique optoelectronic properties. These nanoparticles are widely used for a variety of different applications. However, there are many unresolved issues that lower the efficiency and/or stability of devices which incorporate these NCs. Our research is dedicated to addressing these issues by identifying potential problems and resolving them, improving existing systems, generating new synthetic strategies, and/or building new devices. The general strategies for the synthesis of different nanocrystals were established in this work, one of which is the colloidal growth of gold domains onto CdS semiconductor nanocrystals. Control of shape and size was achieved simply by adjusting the temperature and the time of the reaction. Depending on the exact morphology of Au and CdS domains, fabricated nano-composites can undergo evaporation-induced self-assembly onto a substrate, which is very useful for building devices. CdS/Au heterostructures can assemble in two different ways: through end-to-end coupling of Au domains, resulting in the formation of one-dimensional chains; and via side-by-side packing of CdS nanorods, leading to the onset of two-dimensional superlattices. We investigated the nature of exciton-plasmon interactions in Au-tipped CdS nanorods using femtosecond transient absorption spectroscopy. The study demonstrated that the key optoelectronic properties of electrically coupled metal and semiconductor domains are significantly different from those observed in systems with weak inter-domain coupling. In particular, strongly-coupled nanocomposites promote mixing of electronic states at semiconductor-metal domain interfaces, which causes a significant suppression of both plasmon and exciton carrier excitations. Colloidal QDs are starting to replace organic molecules in many different applications, such as organic light emmiting diods (OLEDs), due to their

  1. Nonvolatile transtance change random access memory based on magnetoelectric P(VDF-TrFE)/Metglas heterostructures

    Science.gov (United States)

    Lu, Peipei; Shang, Dashan; Shen, Jianxin; Chai, Yisheng; Yang, Chuansen; Zhai, Kun; Cong, Junzhuang; Shen, Shipeng; Sun, Young

    2016-12-01

    Transtance change random access memory (TCRAM) is a type of nonvolatile memory based on the nonlinear magnetoelectric coupling effects of multiferroics. In this work, ferroelectric P(VDF-TrFE) thin films were prepared on Metglas foil substrates by the sol-gel technique to form multiferroic heterostructures. The magnetoelectric voltage coefficient of the heterostructure can be switched reproducibly to different levels between positive and negative values by applying selective electric-field pulses. Compared with bulk multiferroic heterostructures, the polarization switching voltage was reduced to 7 V. Our facile technological approach enables this organic magnetoelectric heterostructure as a promising candidate for the applications in multilevel TCRAM devices.

  2. In-plane heterostructures of Sb/Bi with high carrier mobility

    Science.gov (United States)

    Zhao, Pei; Wei, Wei; Sun, Qilong; Yu, Lin; Huang, Baibiao; Dai, Ying

    2017-06-01

    In-plane two-dimensional (2D) heterostructures have been attracting public attention due to their distinctive properties. However, the pristine materials that can form in-plane heterostructures are reported only for graphene, hexagonal BN, transition-metal dichalcogenides. It will be of great significance to explore more suitable 2D materials for constructing such ingenious heterostructures. Here, we demonstrate two types of novel seamless in-plane heterostructures combined by pristine Sb and Bi monolayers by means of first-principle approach based on density functional theory. Our results indicate that external strain can serve as an effective strategy for bandgap engineering, and the transition from semiconductor to metal occurs when a compressive strain of -8% is applied. In addition, the designed heterostructures possess direct band gaps with high carrier mobility (˜4000 cm2 V-1 s-1). And the mobility of electrons and holes have huge disparity along the direction perpendicular to the interface of Sb/Bi in-plane heterostructures. It is favorable for carriers to separate spatially. Finally, we find that the band edge positions of Sb/Bi in-plane heterostructures can meet the reduction potential of hydrogen generation in photocatalysis. Our results not only offer alternative materials to construct versatile in-plane heterostructures, but also highlight the applications of 2D in-plane heterostructures in diverse nanodevices and photocatalysis.

  3. Synthesis, optical and electrochemical properties of ZnO nanowires/graphene oxide heterostructures

    National Research Council Canada - National Science Library

    Zeng, Huidan; Cao, Ying; Xie, Shufan; Yang, Junhe; Tang, Zhihong; Wang, Xianying; Sun, Luyi

    2013-01-01

    .... Electrochemical property measurement results demonstrated that the ZnO nanowires/graphene oxide have large integral area of cyclic voltammetry loop, indicating that such heterostructure is promising...

  4. Observation of long-lived interlayer excitons in monolayer MoSe2-WSe2 heterostructures

    National Research Council Canada - National Science Library

    Rivera, Pasqual; Schaibley, John R; Jones, Aaron M; Ross, Jason S; Wu, Sanfeng; Aivazian, Grant; Klement, Philip; Seyler, Kyle; Clark, Genevieve; Ghimire, Nirmal J; Yan, Jiaqiang; Mandrus, D G; Yao, Wang; Xu, Xiaodong

    2015-01-01

    ..., that is, interlayer excitons. Here, we report the observation of interlayer excitons in monolayer MoSe2-WSe2 heterostructures by photoluminescence and photoluminescence excitation spectroscopy...

  5. Nanotube networks in liquid crystals

    Science.gov (United States)

    Urbanski, Martin; Lagerwall, Jan Peter F.; Scalia, Giusy

    2016-03-01

    Liquid crystals (LCs) are very attractive hosts for the organization of anisotropic nanoparticles such as carbon nanotubes (CNTs) because of the macroscopic organization resulting in properties of nanoparticles manifest at a macroscopic scale. Different types of LCs have demonstrated the ability to organize nanotubes, showing the generality of the approach, i.e., that the liquid crystallinity per se is the driving factor for the organization. Compared to standard nanotube composites (e.g. with disordered polymer hosts) the introduction of carbon nanotubes into an LC allows not only the transfer of the outstanding CNT properties to the macroscopic phase, providing strength and conductivity, but these properties also become anisotropic, following the transfer of the orientational order from the LC to the CNTs. The LC molecular structure plays an important even if ancillary role since it enters in the surface interactions, fulfilling a mediating action between the particle and the bulk of the LC. Isolated nanotubes can be obtained by optimized dispersions at lower concentrations and this process requires the use or development of tailored strategies like using solvents or even another LC for pre-dispersing CNTs. Aggregates or networks can be observed in poor dispersions and at higher nanoparticle concentrations. In those, due to surface interactions, the LC behaviour can be strongly affected with changes in phase sequences or transition temperatures and the effect is expected to be more pronounced as the concentration of nanotubes increases. We present preliminary investigations and observations on nanotube - LC systems based on a smectic LC host.

  6. Anomalous dispersion and superluminal group velocity in a coaxial photonic crystal: theory and experiment.

    Science.gov (United States)

    Haché, A; Poirier, L

    2002-03-01

    We demonstrate that coaxial cables with a periodic impedance exhibit dispersion properties specific to photonic crystals, albeit on a much lower frequency scale. Highly superluminal (>2c) pulse propagation is observed near the photonic band gap at 10 MHz. The influence of group velocity dispersion and crystal length on the traveling speed and shape of a Gaussian pulse are discussed. Results compare favorably with a simple multilayer theory and a coupled-mass model of the structure.

  7. Production of field-reversed mirror plasma with a coaxial plasma gun

    Science.gov (United States)

    Hartman, C.W.; Shearer, J.W.

    The use of a coaxial plasma gun to produce a plasma ring which is directed into a magnetic field so as to form a field-reversed plasma confined in a magnetic mirror. Plasma thus produced may be used as a target for subsequent neutral beam injection or other similarly produced and projected plasma rings or for direct fusion energy release in a pulsed mode.

  8. Microwave Interferometry Based On Open-ended Coaxial Technique for High Sensitivity Liquid Sensing

    Directory of Open Access Journals (Sweden)

    H. Bakli

    2017-10-01

    Full Text Available This paper describes a modified open-ended coaxial technique for microwave dielectric characterization in liquid media. A calibration model is developed to relate the measured transmission coefficient to the local properties of the sample under test. As a demonstration, the permittivity of different sodium chloride solutions is experimentally determined. Accuracies of 0.17% and 0.19% are obtained respectively for the real and imaginary parts of dielectric permittivity at 5.9 GHz.

  9. Microwave generation enhancement of X-band CRBWO by use of coaxial dual annular cathodes

    Directory of Open Access Journals (Sweden)

    Yan Teng

    2013-07-01

    Full Text Available This paper presents an approach that greatly enhances both the output power and the conversion efficiency of the coaxial relativistic backward wave oscillator (CRBWO by using coaxial dual annular cathodes, which increases the diode current rather than the diode voltage. The reasons for the maladjustment of CRBWO under a high diode voltage are analyzed theoretically. It is found that by optimization of the diode structure, the shielding effect of the space charge of the outer beams on the inner cathode can be alleviated effectively and dual annular beams with the same kinetic energy can be explosively emitted in parallel. The coaxial reflector can enhance the conversion efficiency by improving the premodulation of the beams. The electron dump on the inner conductor ensures that the electron beams continue to provide kinetic energy to the microwave output until they vanish. Particle-in-cell (PIC simulation results show that generation can be enhanced up to an output power level of 3.63 GW and conversion efficiency of 45% at 8.97 GHz under a diode voltage of 659 kV and current of 12.27 kA. The conversion efficiency remains above 40% and the output frequency variation is less than 100 MHz over a voltage range of more than 150 kV. Also, the application of the coaxial dual annular cathodes means that the diode impedance is matched to that of the transmission line of the accelerators. This impedance matching can effectively eliminate power reflection at the diode, and thus increase the energy efficiency of the entire system.

  10. The geomagnetic field - An explanation for the microturbulence in coaxial gun plasmas

    Science.gov (United States)

    Mather, J. W.; Ahluwalia, H. S.

    1988-01-01

    The complexity introduced by the geomagnetic field in several regions of a coaxial gun plasma device is described. It is shown that the annihilation of the swept-up geomagnetic flux, trapped within the highly compressed turbulent plasma, provides an explanation for varied performance and experimental results. The results indicate that the device should be aligned along the direction of the local geomagnetic field or enclosed in a mu-metal shield.

  11. Wound temperature profiles of coaxial mini-incision versus sleeveless microincision phacoemulsification.

    Science.gov (United States)

    Belkin, Avner; Abulafia, Adi; Michaeli, Adi; Ofir, Shay; Assia, Ehud I

    2017-04-01

    Temperature profiles at the corneal wound of coaxial mini-incision (2.4 mm) cataract surgery and sleeveless microincision (1.1 mm) cataract surgery were compared. Prospective, controlled, paired-eye clinical trial conducted in a tertiary care hospital. Twenty patients with mild-to-moderate bilateral nuclear sclerotic cataract. Twenty patients underwent bilateral cataract surgery within a 1-month period. One eye was operated on by conventional coaxial mini-incision (2.4 mm) phacoemulsification. The second eye underwent microincision surgery by using a naked phacoemulsification tip and a specialized 19-gauge anterior chamber maintainer as the sole fluid source (three-port microincision cataract surgery technique). Patients had moderate bilateral cataracts with no other anterior segment pathology. Temperature at the corneal wound was constantly recorded by using infrared thermal imaging. Temperatures at the corneal wound. Mean temperatures at the corneal surgical wound were not significantly different between the coaxial and sleeveless groups (31.1 °C ± 2.3 vs. 31.0 °C ± 2. 0; P = 0.89). There was also no difference in maximum temperatures reached during phaco-emulsification. Temperatures did not rise above 40 °C during any surgery, and there were no corneal burns. Final visual acuity and intraoperative and postoperative complication rates were similar between the two groups. The temperature profile at the surgical wound using a microincisional sleeveless phacoemulsification technique is comparable with that of the conventional coaxial mini-incision method. © 2016 Royal Australian and New Zealand College of Ophthalmologists.

  12. Carbon Nanotube Thermoelectric Coolers

    Science.gov (United States)

    2015-02-06

    fitting the sharp features with the Gauss bell curves as was suggested earlier in Ref. (Yang, Fedorov et al. 2012). Comparing the  eG V curves...Yang, Fedorov et al. 2012). Our experimental results suggest that the electric current along the nanotube induces an impressive change of local...fermions, Eur. Phys. J. B (2014) 87: 99 DOI: 10.1140/epjb/e2014-40794-0. 2. Y. Yang, G. Fedorov , J. Zhang, A. Tselev, S. Shafraniuk and P. Barbara

  13. Functionalized boron nitride nanotubes

    Science.gov (United States)

    Sainsbury, Toby; Ikuno, Takashi; Zettl, Alexander K

    2014-04-22

    A plasma treatment has been used to modify the surface of BNNTs. In one example, the surface of the BNNT has been modified using ammonia plasma to include amine functional groups. Amine functionalization allows BNNTs to be soluble in chloroform, which had not been possible previously. Further functionalization of amine-functionalized BNNTs with thiol-terminated organic molecules has also been demonstrated. Gold nanoparticles have been self-assembled at the surface of both amine- and thiol-functionalized boron nitride Nanotubes (BNNTs) in solution. This approach constitutes a basis for the preparation of highly functionalized BNNTs and for their utilization as nanoscale templates for assembly and integration with other nanoscale materials.

  14. Elastocapillary assembly of silver nanotube forest

    Science.gov (United States)

    Yang, Xin; Pack, Min; Sun, Ying

    2014-11-01

    Nanorods/nanotubes have large surface areas making them promising for applications such as high-performance battery and capacitor electrodes, photovoltaics, and interconnects. In this study, we demonstrate the formation of 3D microarchitectures via elastocapillary self-assembly of silver nanotube forests. Patterned silver nanotube forests of different lengths and diameters are made by inkjet printing of silver nanoinks into nanoporous anodic aluminum oxide membranes. These silver nanotube forests are then self-assembled into ordered microstructures via capillary forces induced by liquid condensation, which is compared with immersing nanotubes directly into a liquid. The effects of length, diameter, and footprint of the nanotube forest on self-assembled patterns are systematically studied. By decreasing the footprint and/or increasing the length of nanotube forest, the stiffness of the nanotube forest decreases, bringing the nanotubes together to form closely packed microstructures.

  15. Empirical source noise prediction method with application to subsonic coaxial jet mixing noise

    Science.gov (United States)

    Zorumski, W. E.; Weir, D. S.

    1982-01-01

    A general empirical method, developed for source noise predictions, uses tensor splines to represent the dependence of the acoustic field on frequency and direction and Taylor's series to represent the dependence on source state parameters. The method is applied to prediction of mixing noise from subsonic circular and coaxial jets. A noise data base of 1/3-octave-band sound pressure levels (SPL's) from 540 tests was gathered from three countries: United States, United Kingdom, and France. The SPL's depend on seven variables: frequency, polar direction angle, and five source state parameters: inner and outer nozzle pressure ratios, inner and outer stream total temperatures, and nozzle area ratio. A least-squares seven-dimensional curve fit defines a table of constants which is used for the prediction method. The resulting prediction has a mean error of 0 dB and a standard deviation of 1.2 dB. The prediction method is used to search for a coaxial jet which has the greatest coaxial noise benefit as compared with an equivalent single jet. It is found that benefits of about 6 dB are possible.

  16. Coaxial CVD diamond detector for neutron diagnostics at ShenGuang III laser facility

    Science.gov (United States)

    Yu, Bo; Liu, Shenye; Chen, Zhongjing; Huang, Tianxuan; Jiang, Wei; Chen, Bolun; Pu, Yudong; Yan, Ji; Zhang, Xing; Song, Zifeng; Tang, Qi; Hou, Lifei; Ding, Yongkun; Zheng, Jian

    2017-06-01

    A coaxial, high performance diamond detector has been developed for neutron diagnostics of inertial confinement fusion at ShenGuangIII laser facility. A Φ10 mm × 1 mm "optical grade" chemical-vapor deposition diamond wafer is assembled in coaxial-designing housing, and the signal is linked to a SubMiniature A connector by the cathode cone. The coaxial diamond detector performs excellently for neutron measurement with the full width at half maximum of response time to be 444 ps for a 50 Ω measurement system. The average sensitivity is 0.677 μV ns/n for 14 MeV (DT fusion) neutrons at an electric field of 1000 V/mm, and the linear dynamic range is beyond three orders of magnitude. The ion temperature results fluctuate widely from the neutron time-of-flight scintillator detector results because of the short flight length. These characteristics of small size, large linear dynamic range, and insensitive to x-ray make the diamond detector suitable to measure the neutron yield, ion temperature, and neutron emission time.

  17. Study of Performance of Coaxial Vacuum Tube Solar Collector on Ethanol Distillation Process

    Science.gov (United States)

    Sutomo; Ramelan, A. H.; Mustafa; Tristono, T.

    2017-07-01

    Coaxial vacuum tube solar collectors can generate heat up to 80°C is possibly used for ethanol distillation process that required temperature 79°C only. This study reviews the performance of coaxial collector vacuum tube used for ethanol distillation process. This experimental research was conducted in a closed space using a halogen lamp as a solar radiation simulator. We had done on three different of the radiation values, i.e. 998 W/m2, 878 W/m2 and 782 W/m2. The pressure levels of vacuum tube collector cavity in the research were 1; 0.5; 0.31; 0.179; and 0.043 atmospheres. The Research upgraded the 30% of ethanol to produce the concentration of 77% after distillation. The result shows that the performance of coaxial collector vacuum tube used for ethanol distillation process has the negative correlation to the level of the collector tube cavity pressure. The productivity will increase while the collector tube cavity pressure decreased. Therefore, the collector efficiency has the negative correlation also to the level of collector tube cavity pressure. The best performance achieved when it operated at a pressure of 0.043 atmosphere with radiation intensity 878 W / m2, and the value of efficiency is 57.8%.

  18. Comparison of the coaxial circle circuit with the conventional circle circuit.

    Science.gov (United States)

    Mizrak, Ayse; Bilgi, Murat; Koruk, Senem; Ganidagli, Suleyman; Karatas, Erkan; Oner, Unsal; Gul, Rauf; Sahin, Levent

    2011-08-01

    The coaxial circle system helps prevent heat loss during surgery, and it also acts as a humidifier. This study aimed to compare the coaxial breathing system and the conventional system in their ability to warm and moisturize inhaled gases, and we also analyzed lung function protection and saccharin clearance time in patients who underwent tympanomastoidectomy (TMT) with the aid of these two systems. Forty adult patients of ASA physical status I-II were scheduled for elective TMT. A standard volume-dependent ventilator setting was used to establish normocapnia. The coaxial circle system was used in the treated group (n=20), whereas the conventional circuit system was used in the control group (n=20). Saccharin clearance, VC (vital capacity), FRC (functional residual capacity), FEV1 (forced expiratory volume in 1 second), airway pressure, relative humidity and temperature of inspired gas, body temperature and adverse and hemodynamic effects were measured at different perioperative periods. The relative humidity (mg H2O Lt -1) of inspired gas in the treated group was higher than in the control group at 5, 15, 30, 45, 60 and 90 minutes after anesthesia induction. The temperature of inspired gas (Centigrade) in the treated group was higher than in the control group (pcircle system decreased postoperative saccharin clearance time and increased postoperative FRC, relative humidity and the temperature of inspired fresh gas, without any adverse perioperative effects in patients who underwent TMT.

  19. 3D beam shape estimation based on distributed coaxial cable interferometric sensor

    Science.gov (United States)

    Cheng, Baokai; Zhu, Wenge; Liu, Jie; Yuan, Lei; Xiao, Hai

    2017-03-01

    We present a coaxial cable interferometer based distributed sensing system for 3D beam shape estimation. By making a series of reflectors on a coaxial cable, multiple Fabry-Perot cavities are created on it. Two cables are mounted on the beam at proper locations, and a vector network analyzer (VNA) is connected to them to obtain the complex reflection signal, which is used to calculate the strain distribution of the beam in horizontal and vertical planes. With 6 GHz swept bandwidth on the VNA, the spatial resolution for distributed strain measurement is 0.1 m, and the sensitivity is 3.768 MHz mɛ -1 at the interferogram dip near 3.3 GHz. Using displacement-strain transformation, the shape of the beam is reconstructed. With only two modified cables and a VNA, this system is easy to implement and manage. Comparing to optical fiber based sensor systems, the coaxial cable sensors have the advantage of large strain and robustness, making this system suitable for structure health monitoring applications.

  20. High power operation of the university of Maryland coaxial gyroklystron experiment

    Energy Technology Data Exchange (ETDEWEB)

    Lawson, W.; Arjona, M.; Castle, M.; Hogan, B.; Granatstein, V.; Reiser, M. [Institute for Plasma Research and Electrical Engineering Department, University of Maryland, College Park, Maryland 20742 (United States)

    1999-07-01

    We report the experimental studies of high power amplification in a coaxial three-cavity X-band gyroklystron. A single-anode magnetron injection gun (MIG) is used to produce a 520 A beam of 470 keV electrons with an average ratio of perpendicular-to-parallel velocity of about one. The voltage flat top is nearly 2 {mu}s. All cavities are designed to operate in the TE{sub 011} coaxial mode near 8.6 GHz. The input cavity is driven by a 150 kW, 3 {mu}s coaxial magnetron through a single slot in the radial wall. Peak powers of 75{endash}85 MW are measured with a conversion efficiency of nearly 32{percent} and a large signal gain of about 30 dB. This performance is in good agreement with simulations and represents approximately a tri-fold increase in the peak power capability of pulsed X-band gyroklystrons. We also report on the design of a three cavity second harmonic gyroklystron which is expected to produce 100 MW at 17.14 GHz. We close with a general discussion of scaling our designs to higher frequencies. {copyright} {ital 1999 American Institute of Physics.}

  1. Influence of sheath solvents on the quality of ethyl cellulose nanofibers in a coaxial electrospinning process.

    Science.gov (United States)

    Yu, Deng-Guang; Li, Xiao-Yan; Chian, Wei; Li, Ying; Wang, Xia

    2014-01-01

    The influence of different types of solvents as sheath fluids on the quality of electrospun ethyl cellulose (EC) nanofibers is investigated in this paper by a modified coaxial process. With 24 w/v % EC in ethanol as electrospinning core fluid and pure solvents including methanol, ethanol and N,N-dimethyl formamide (DMF) as sheath fluids, EC nanofibers were generated by the modified processes. Field emission scanning electron microscope observations demonstrate that the modified process is effective in improving the nanofibers' quality in terms of nanofibers' diameters, distributions and structural uniformity. The key of the modified coaxial process is the reasonable selection of the sheath solvents that is suitable for the drawing process of core EC fluid during the electrpospinning. The EC nanofibers' diameters (D, nm) could be manipulated through the reasonable selection of the type of the sheath solvents based on their boiling point (T, °C) D = 841-3.71T (R=0.9753). This paper provides useful methods for the implementation of the modified coaxial process controllably to obtain polymer nanofibers with high quality.

  2. Rapid 3D Printing of Multifunctional Calcium Alginate Gel Pipes using Coaxial Jet Extruder

    Science.gov (United States)

    Rykaczewski, Konrad; Damle, Viraj

    2014-11-01

    Calcium alginate (CA) forms when solution containing sodium alginate (SA) comes in contact with a CaCl2 solution. The resulting gel is biocompatible as well as edible and is used in production of bio-scaffolds, artificial plant seeds, and edible substances. In the latter application, referred to in the culinary world as ``spherification,'' flavored liquids are mixed with the SA and dripped into CaCl2 solution to form gel encapsulated flavored ``marbles.'' Previously, crude 3D printing of CA structures has been achieved by stacking of such flavored liquid filled marbles. In turn, solid CA rods have been fabricated by properly mixing flow of the two solutions using a microfluidic device. Here we show that by using two circular cross-section coaxial nozzles to produce coaxial jets of the SA and CaCl2 solutions, liquid filled CA micro-to-mili scale gel pipes can be produced at speeds around ~ 150 mm/s. Such extrusion rate is compatible with most commercially available 3D printers, facilitating adoption of the CA pipe coaxial jet extruder. Here, the impact of inner and outer liquid properties and flow speeds on the gel pipe extrusion process is discussed. KR acknowledges startup funding from ASU.

  3. Usefulness of the coaxial technique in US-guided breast core biopsy

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Hyun; Lee, Jeong Hwa; Ha, Jeon Ju; Lee, Keon; Kim, Won Ho; Kwon, Jung Hyeok [Dongkang general hospital, Seoul (Korea, Republic of); Ham, Soo Youn [Ulsan Univ. Hospital, Ulsan (Korea, Republic of)

    1999-05-01

    To evaluate the usefulness of the coaxial technique in US-guided breast core biopsy. Using the coaxial technique, US-guided breast core biopsy was performed in 49 breast lesions (40 patients). Under US-guidance the 17-gauge, 13 cm long introducer needle was positioned proximal to the lesion. Once the needle was in place, the central trocar was removed and was replaced with the core biopsy needle. We used an 18-gauge, 16-cm-long core biopsy needle with a 17 mm specimen notch. Four to eight tissue specimens were obtained from each lesion, and the quality and quantity of specimens, procedure time, and complications and their rate were evaluated. For 48 of 49 lesions, specimens were adequate for histopathologic diagnosis, and the findings were as follows : six cases of invasive ductal carcinoma, one of ductal carcinoma in situ, 29 of fibrocystic disease, eight of fibroadenoma, two of chronic inflammation, and two of sclerosing lesion. In 12 lesions agreement between the pathologic results of needle core biopsy and surgical results was 100%. The procedure time was about 15 minutes and no significant complications were noted. In breast core biopsy, the coaxial technique is simple and time-saving, and compared with standard breast core biopsy, may also be less traumatic and decrease the potential risk of seeding the biopsy tract with malignant cells.

  4. Coaxial-gun design and testing for the PLX- α Project

    Science.gov (United States)

    Witherspoon, F. Douglas; Brockington, Samuel; Case, Andrew; Cruz, Edward; Luna, Marco; Langendorf, Samuel

    2016-10-01

    We describe the Alpha coaxial gun designed for a 60-gun scaling study of spherically imploding plasma liners as a standoff driver for plasma-jet-driven magneto-inertial fusion (PJMIF). The guns operate over a range of parameters: 0.5-5.0 mg of Ar, Ne, N2, Kr, and Xe; 20-60 km/s; 2 × 1016 cm-3 muzzle density; and up to 7.5 kJ stored energy per gun. Each coaxial gun incorporates a fast dense gas injection and triggering system, a compact low-weight pfn with integral sparkgap switching, and a contoured gap designed to suppress the blow-by instability. The latest design iteration incorporates a faster more robust gas valve, an improved electrode contour, a custom 600- μF, 5-kV pfn, and six inline sparkgap switches operated in parallel. The switch and pfn are mounted directly to the back of the gun and are designed to reduce inductance, cost, and complexity, maximize efficiency and system reliability, and ensure symmetric current flow. We provide a brief overview of the design choices, the projected performance over the parameter ranges mentioned above, and experimental results from testing of the PLX- α coaxial gun. This work supported by the ARPA-E ALPHA Program.

  5. Investigation of a Novel Coaxial Power-Split Hybrid Powertrain for Mining Trucks

    Directory of Open Access Journals (Sweden)

    Weiwei Yang

    2018-01-01

    Full Text Available Due to the different working conditions and specification requirements of mining trucks when compared to commercial passenger vehicles, better fuel efficiency of mining trucks could lead to more significant economic benefits. Therefore, investigating a hybrid transmission system becomes essential. A coaxial power-split hybrid powertrain system for mining trucks is presented in this paper. The system is characterized as comprising an engine, a generator (MG1, a motor (MC2, two sets of planetary gears, and a clutch (CL1. There are six primary operation modes for the hybrid system including the electric motor mode, the engine mode, the hybrid electric mode, the hybrid and assist mode, the regenerative mode, and the stationary charging mode. The mathematical model of the coaxial power-split hybrid system is established according to the requirements of vehicle dynamic performance and fuel economy performance in a given driving cycle. A hybrid vehicle model based on a rule-based control strategy is established to evaluate the fuel economy. Compared with the Toyota Hybrid System (THS and the conventional mechanical vehicle system using a diesel engine, the simulation results based on an enterprise project indicate that the proposed hybrid system can enhance the vehicle’s fuel economy by 8.21% and 22.45%, respectively, during the given mining driving cycle. The simulation results can be used as a reference to study the feasibility of the proposed coaxial hybrid system whose full potential needs to be further investigated by adopting non-causal control strategies.

  6. Design of a Facility for Studying Shock-Cell Noise on Single and Coaxial Jets

    Directory of Open Access Journals (Sweden)

    Daniel Guariglia

    2018-03-01

    Full Text Available Shock-cell noise occurs in aero-engines when the nozzle exhaust is supersonic and shock-cells are present in the jet. In commercial turbofan engines, at cruise, the secondary flow is often supersonic underexpanded, with the formation of annular shock-cells in the jet and consequent onset of shock-cell noise. This paper aims at describing the design process of the new facility FAST (Free jet AeroacouSTic laboratory at the von Karman Institute, aimed at the investigation of the shock-cell noise phenomenon on a dual stream jet. The rig consists of a coaxial open jet, with supersonic capability for both the primary and secondary flow. A coaxial silencer was designed to suppress the spurious noise coming from the feeding lines. Computational fluid dynamics (CFD simulations of the coaxial jet and acoustic simulations of the silencer have been carried out to support the design choices. Finally, the rig has been validated by performing experimental measurements on a supersonic single stream jet and comparing the results with the literature. Fine-scale PIV (Particle Image Velocimetry coupled with a microphone array in the far field have been used in this scope. Preliminary results of the dual stream jet are also shown.

  7. NASA Innovation Builds Better Nanotubes

    Science.gov (United States)

    2008-01-01

    Nanotailor Inc., based in Austin, Texas, licensed Goddard Space Flight Center's unique single-walled carbon nanotube (SWCNT) fabrication process with plans to make high-quality, low-cost SWCNTs available commercially. Carbon nanotubes are being used in a wide variety of applications, and NASA's improved production method will increase their applicability in medicine, microelectronics, advanced materials, and molecular containment. Nanotailor built and tested a prototype based on Goddard's process, and is using this technique to lower the cost and improve the integrity of nanotubes, offering a better product for use in biomaterials, advanced materials, space exploration, highway and building construction, and many other applications.

  8. Abrupt Schottky Junctions in Al/Ge Nanowire Heterostructures.

    Science.gov (United States)

    Kral, S; Zeiner, C; Stöger-Pollach, M; Bertagnolli, E; den Hertog, M I; Lopez-Haro, M; Robin, E; El Hajraoui, K; Lugstein, A

    2015-07-08

    In this Letter we report on the exploration of axial metal/semiconductor (Al/Ge) nanowire heterostructures with abrupt interfaces. The formation process is enabled by a thermal induced exchange reaction between the vapor-liquid-solid grown Ge nanowire and Al contact pads due to the substantially different diffusion behavior of Ge in Al and vice versa. Temperature-dependent I-V measurements revealed the metallic properties of the crystalline Al nanowire segments with a maximum current carrying capacity of about 0.8 MA/cm(2). Transmission electron microscopy (TEM) characterization has confirmed both the composition and crystalline nature of the pure Al nanowire segments. A very sharp interface between the ⟨111⟩ oriented Ge nanowire and the reacted Al part was observed with a Schottky barrier height of 361 meV. To demonstrate the potential of this approach, a monolithic Al/Ge/Al heterostructure was used to fabricate a novel impact ionization device.

  9. Novel heterostructured Ge nanowires based on polytype transformation.

    Science.gov (United States)

    Vincent, Laetitia; Patriarche, Gilles; Hallais, Géraldine; Renard, Charles; Gardès, Cyrille; Troadec, David; Bouchier, Daniel

    2014-08-13

    We report on a strain-induced phase transformation in Ge nanowires under external shear stresses. The resulted polytype heterostructure may have great potential for photonics and thermoelectric applications. ⟨111⟩-oriented Ge nanowires with standard diamond structure (3C) undergo a phase transformation toward the hexagonal diamond phase referred as the 2H-allotrope. The phase transformation occurs heterogeneously on shear bands along the length of the nanowire. The structure meets the common phenomenological criteria of a martensitic phase transformation. This point is discussed to initiate an on going debate on the transformation mechanisms. The process results in unprecedented quasiperiodic heterostructures 3C/2H along the Ge nanowire. The thermal stability of those 2H domains is also studied under annealing up to 650 °C by in situ TEM.

  10. Photoresponsive memory device based on Graphene/Boron Nitride heterostructure

    Science.gov (United States)

    Kahn, Salman; Velasco, Jairo, Jr.; Ju, Long; Wong, Dillon; Lee, Juwon; Tsai, Hsin Zon; Taniguchi, Takashi; Watanabe, Kenji; Zettl, Alex; Wang, Feng; Crommie, Michael

    2015-03-01

    Recent technological advancements have allowed the stacking of two dimensional layered material in order to create van der Waals heterostructures (VDH), enabling the design of novel properties by exploiting the proximal interaction between layers with different electronic properties. We report the creation of an optoelectronic memory device using a Graphene/Boron Nitride (hBN) heterostructure. Using the photo-induced doping phenomenon, we are able to spatially ``write'' a doping profile on graphene and ``read'' the profile through electrical transport and local probe techniques. We then utilize defect engineering to enhance the optoelectronic response of graphene and explore the effect of defects in hBN. Our work introduces a simple device architecture to create an optoelectronic memory device and contributes towards understanding the proximal effects of hBN on Graphene.

  11. Multifunctional high-performance van der Waals heterostructures

    Science.gov (United States)

    Huang, Mingqiang; Li, Shengman; Zhang, Zhenfeng; Xiong, Xiong; Li, Xuefei; Wu, Yanqing

    2017-12-01

    A range of novel two-dimensional materials have been actively explored for More Moore and More-than-Moore device applications because of their ability to form van der Waals heterostructures with unique electronic properties. However, most of the reported electronic devices exhibit insufficient control of multifunctional operations. Here, we leverage the band-structure alignment properties of narrow-bandgap black phosphorus and large-bandgap molybdenum disulfide to realize vertical heterostructures with an ultrahigh rectifying ratio approaching 106 and on-off ratio up to 107. Furthermore, we design and fabricate tunable multivalue inverters, in which the output logic state and window of the mid-logic can be controlled by specific pairs of channel length and, most importantly, by the electric field, which shifts the band-structure alignment across the heterojunction. Finally, high gains over 150 are achieved in the inverters with optimized device geometries, showing great potential for future logic applications.

  12. Prismatic quantum heterostructures on MBE grown GaAs nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Fontcuberta i Morral, Anna [Walter Schottky Institut, TU Muenchen, Garching (Germany)

    2008-07-01

    Semiconductor nanowires are believed to play a decisive role in the electronic and optoelectronic devices of the XXI century. Their synthesis is a rapidly expanding field, due to the expectations that nanoscale objects and their associated phenomena have to offer to basic and applied science. Here we report on a new method for the growth of GaAs nanowires and related prismatic quantum heterostructures using Molecular Beam Epitaxy (MBE), by avoiding the use of gold as seed for the nanowires. The use of Molecular Beam Epitaxy presents an additional interest, as this technique allows us to produce ultra-pure nanowires and quantum heterostructures on the nanowire facets with very high crystalline quality and atomically sharp interfaces. This new versatility of MBE in the growth of nanostructures opens great possibilities for the generation of novel devices with additional optical and electronic functionalities, as it has been previously shown in planar structures.

  13. Millimeter-wave and optoelectronic applications of heterostructure integrated circuits

    Science.gov (United States)

    Pavlidis, Dimitris

    1991-01-01

    The properties are reviewed of heterostructure devices for microwave-monolithic-integrated circuits (MMICs) and optoelectronic integrated circuits (OICs). Specific devices examined include lattice-matched and pseudomorphic InAlAs/InGaAs high-electron mobility transistors (HEMTs), mixer/multiplier diodes, and heterojunction bipolar transistors (HBTs) developed with a number of materials. MMICs are reviewed that can be employed for amplification, mixing, and signal generation, and receiver/transmitter applications are set forth for OICs based on GaAs and InP heterostructure designs. HEMTs, HBTs, and junction-FETs can be utilized in combination with PIN, MSM, and laser diodes to develop novel communication systems based on technologies that combine microwave and photonic capabilities.

  14. Axial Ge/Si nanowire heterostructure tunnel FETs

    Energy Technology Data Exchange (ETDEWEB)

    Picraux, Sanuel T [Los Alamos National Laboratory; Daych, Shadi A [Los Alamos National Laboratory

    2010-01-01

    The vapor-liquid-solid (VLS) growth of semiconductor nanowires allows doping and composition modulation along their axis and the realization of axial 1 D heterostructures. This provides additional flexibility in energy band-edge engineering along the transport direction which is difficult to attain by planar materials growth and processing techniques. We report here on the design, growth, fabrication, and characterization of asymmetric heterostructure tunnel field-effect transistors (HTFETs) based on 100% compositionally modulated Si/Ge axial NWs for high on-current operation and low ambipolar transport behavior. We discuss the optimization of band-offsets and Schottky barrier heights for high performance HTFETs and issues surrounding their experimental realization. Our HTFET devices with 10 nm PECVD SiN{sub x} gate dielectric resulted in a measured current drive exceeding 100 {mu}A/{mu}m (I/{pi}D) and 10{sup 5} I{sub on}/I{sub off} ratios.

  15. High ionic conductivity in confined bismuth oxide-based heterostructures

    DEFF Research Database (Denmark)

    Sanna, Simone; Esposito, Vincenzo; Christensen, Mogens

    2016-01-01

    Bismuth trioxide in the cubic fluorite phase (δ-Bi2O3) exhibits the highest oxygen ionic conductivity. In this study, we were able to stabilize the pure -Bi2O3 at low temperature with no addition of stabilizer but only by engineering the interface, using highly coherent heterostructures made...... of alternative layers of δ-Bi2O3 and Yttria Stabilized Zirconia (YSZ), deposited by pulsed laser deposition. The resulting [δ-Bi2O3=YSZ] heterostructures are found to be stable over a wide temperature range (500-750 °C) and exhibits stable high ionic conductivity over a long time comparable to the value...... of the pure δ-Bi2O3, which is approximately two orders of magnitude higher than the conductivity of YSZ bulk....

  16. Band structure engineering in topological insulator based heterostructures.

    Science.gov (United States)

    Menshchikova, T V; Otrokov, M M; Tsirkin, S S; Samorokov, D A; Bebneva, V V; Ernst, A; Kuznetsov, V M; Chulkov, E V

    2013-01-01

    The ability to engineer an electronic band structure of topological insulators would allow the production of topological materials with tailor-made properties. Using ab initio calculations, we show a promising way to control the conducting surface state in topological insulator based heterostructures representing an insulator ultrathin films on the topological insulator substrates. Because of a specific relation between work functions and band gaps of the topological insulator substrate and the insulator ultrathin film overlayer, a sizable shift of the Dirac point occurs resulting in a significant increase in the number of the topological surface state charge carriers as compared to that of the substrate itself. Such an effect can also be realized by applying the external electric field that allows a gradual tuning of the topological surface state. A simultaneous use of both approaches makes it possible to obtain a topological insulator based heterostructure with a highly tunable topological surface state.

  17. Optoelectronics based on 2D TMDs and heterostructures

    Science.gov (United States)

    Huo, Nengjie; Yang, Yujue; Li, Jingbo

    2017-03-01

    2D materials including graphene and TMDs have proven interesting physical properties and promising optoelectronic applications. We reviewed the growth, characterization and optoelectronics based on 2D TMDs and their heterostructures, and demonstrated their unique and high quality of performances. For example, we observed the large mobility, fast response and high photo-responsivity in MoS2, WS2 and WSe2 phototransistors, as well as the novel performances in vdW heterostructures such as the strong interlayer coupling, am-bipolar and rectifying behaviour, and the obvious photovoltaic effect. It is being possible that 2D family materials could play an increasingly important role in the future nano- and opto-electronics, more even than traditional semiconductors such as silicon.

  18. Abrupt Schottky Junctions in Al/Ge Nanowire Heterostructures

    OpenAIRE

    Kral, S.; Zeiner, C.; St?ger-Pollach, M.; Bertagnolli, E.; Den Hertog, M.I.; Lopez-Haro, M.; Robin, E.; El Hajraoui, K.; Lugstein, A.

    2015-01-01

    In this Letter we report on the exploration of axial metal/semiconductor (Al/Ge) nanowire heterostructures with abrupt interfaces. The formation process is enabled by a thermal induced exchange reaction between the vapor?liquid?solid grown Ge nanowire and Al contact pads due to the substantially different diffusion behavior of Ge in Al and vice versa. Temperature-dependent I?V measurements revealed the metallic properties of the crystalline Al nanowire segments with a maximum current carrying...

  19. Liquid phase epitaxial growth of heterostructured hierarchical MOF thin films

    KAUST Repository

    Chernikova, Valeriya

    2017-05-10

    Precise control of epitaxial growth of MOF-on-MOF thin films, for ordered hierarchical tbo-type structures is demonstrated. The heterostructured MOF thin film was fabricated by successful sequential deposition of layers from two different MOFs. The 2-periodic layers, edge-transitive 4,4-square lattices regarded as supermolecular building layers, were commendably cross-linked using a combination of inorganic/organic and organic pillars.

  20. Double-heterostructure cavities: from theory to design

    CERN Document Server

    Mahmoodian, Sahand; Poulton, Christopher G; Dossou, Kokou B; Botten, Lindsay C; McPhedran, Ross C; de Sterke, C Martijn

    2012-01-01

    We derive a frequency-domain-based approach for radiation (FAR) from double-heterostructure cavity (DHC) modes. We use this to compute the quality factors and radiation patterns of DHC modes. The semi-analytic nature of our method enables us to provide a general relationship between the radiation pattern of the cavity and its geometry. We use this to provide general designs for ultrahigh quality factor DHCs with radiation patterns that are engineered to emit vertically.

  1. Ag/CdS heterostructural composites: Fabrication, characterizations and photocatalysis

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yang [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan, Shanxi 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan, Shanxi 030024 (China); Chi, Mei [Institute of Metal Research, Chinese Academy of Sciences, Shenyang, Liaoning 110016 (China); Dong, Hailiang; Jia, Husheng; Xu, Bingshe [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan, Shanxi 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan, Shanxi 030024 (China); Zhang, Zhuxia, E-mail: zhangzhuxia@tyut.edu.cn [Key Laboratory of Interface Science and Engineering in Advanced Materials, Taiyuan University of Technology, Ministry of Education, Taiyuan, Shanxi 030024 (China); College of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan, Shanxi 030024 (China)

    2014-09-15

    Highlights: • Novel Ag/CdS core–shell heterostructural composites were fabricated using a two-step chemical method. • A formation mechanism of Ag/CdS heterostructural composites. • The photocatalytic activity of Ag/CdS heterostructural composites was found to be improved. • PL emissions are markedly quenched in the Ag/CdS composites than in CdS nanoparticles. - Abstract: Ag/CdS heterostructural materials were successfully synthesized by ultrasound-assisted polyols and hydrothermal method. Under hydrothermal condition, thiourea adsorbed on Ag nanowires releases S{sup 2−} ions, which react with vicinal Cd{sup 2+} ions to form CdS clusters on Ag nanowires. Thereafter, the Ag/CdS composites grow into core–shell structure through CdS aggregation, Ostwald ripening, and preferential growth. The obtained core–shell structures and morphologies were investigated by XRD, SEM, and TEM; the experimental results indicate that the composites are composed of Ag nanowires serving as the core and CdS particles as the shell. The photocatalytic property of Ag/CdS core–shell materials was then investigated in detail. Comparing studies on the degradation of methylene blue were employed by using pure CdS, pure Ag, and Ag/CdS composites, respectively. The results show that the Ag/CdS composites possess higher photocatalytic degradation efficiency. Moreover, the Ag/CdS composites show improved stability, and the photocatalytic activity remains almost unchanged after four recycles. The enhanced photocatalytic effect for Ag/CdS composites is mainly attributed to the photogenerated electron transfer from CdS to Ag nanowire, while photogenerated holes still remain in CdS's valence band. Consequently, the effective separation of photogenerated electrons and holes and the resulting OH radicals improve the photocatalytic efficiency of Ag/CdS composites greatly.

  2. Observing Imperfection in Atomic Interfaces for van der Waals Heterostructures

    Science.gov (United States)

    Rooney, Aidan. P.; Kozikov, Aleksey; Rudenko, Alexander N.; Prestat, Eric; Hamer, Matthew J.; Withers, Freddie; Cao, Yang; Novoselov, Kostya S.; Katsnelson, Mikhail I.; Gorbachev, Roman; Haigh, Sarah J.

    2017-09-01

    Vertically stacked van der Waals heterostructures are a lucrative platform for exploring the rich electronic and optoelectronic phenomena in two-dimensional materials. Their performance will be strongly affected by impurities and defects at the interfaces. Here we present the first systematic study of interfaces in van der Waals heterostructure using cross sectional scanning transmission electron microscope (STEM) imaging. By measuring interlayer separations and comparing these to density functional theory (DFT) calculations we find that pristine interfaces exist between hBN and MoS2 or WS2 for stacks prepared by mechanical exfoliation in air. However, for two technologically important transition metal dichalcogenide (TMDC) systems, MoSe2 and WSe2, our measurement of interlayer separations provide the first evidence for impurity species being trapped at buried interfaces with hBN: interfaces which are flat at the nanometer length scale. While decreasing the thickness of encapsulated WSe2 from bulk to monolayer we see a systematic increase in the interlayer separation. We attribute these differences to the thinnest TMDC flakes being flexible and hence able to deform mechanically around a sparse population of protruding interfacial impurities. We show that the air sensitive two dimensional (2D) crystal NbSe2 can be fabricated into heterostructures with pristine interfaces by processing in an inert-gas environment. Finally we find that adopting glove-box transfer significantly improves the quality of interfaces for WSe2 compared to processing in air.

  3. Pulsed laser deposition of yttria stabilized zirconia based heterostructure

    Energy Technology Data Exchange (ETDEWEB)

    Pascu, R. [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor Str., PO Box MG-36, Magurele, 077125 Bucharest (Romania); Somacescu, S. [Institute of Physical Chemistry, Romanian Academy, Splaiul Independentei 202, 060021 Bucharest (Romania); Epurescu, G.; Filipescu, M.; Luculescu, C.; Colceag, D. [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor Str., PO Box MG-36, Magurele, 077125 Bucharest (Romania); Osiceanu, P. [Institute of Physical Chemistry, Romanian Academy, Splaiul Independentei 202, 060021 Bucharest (Romania); Birjega, R. [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor Str., PO Box MG-36, Magurele, 077125 Bucharest (Romania); Mitu, B., E-mail: mitub@infim.ro [National Institute for Laser, Plasma and Radiation Physics, 409 Atomistilor Str., PO Box MG-36, Magurele, 077125 Bucharest (Romania)

    2014-02-28

    Yttria stabilized zirconia (YSZ), nickel-doped yttria stabilized zirconia (NiYSZ) thin films and NiYSZ/YSZ anode–electrolyte heterostructure have been synthesized on Si(100) substrate by pulsed laser deposition technique. Atomic Force Microscopy, Scanning Electron Microscopy, and Variable Angle Spectroscopic Ellipsometry studies have been applied to determine the surface topography, film morphology and thickness. The X-ray diffraction measurements evidenced a highly textured growth along (111) direction for NiYSZ/YSZ heterostructure with crystallite dimension of 18 nm. The X-ray photoelectron spectroscopy analysis showed a displacement of Ni oxidation states along the depth profile, with Ni{sup 3+} oxidation state on the surface, a very thin layer containing Ni{sup 2+} associated to NiO buried under the surface, while metallic Ni is predominant in the bulk. The presence of an intermix layer at the interface between the NiYSZ and YSZ, suggested by the ellipsometric measurements, was confirmed by Secondary Neutral Mass Spectrometry data. - Highlights: • Crystalline NiYSZ/YSZ heterostructure with cubic phase was obtained by PLD at 873 K. • The structure presents an intermix layer at the interface between the NiYSZ and YSZ films. • Ni is present on the surface as Ni{sub 2}O{sub 3}, while in the bulk metallic Ni is predominant.

  4. Structural and Electrical Investigation of C60-Graphene Vertical Heterostructures.

    Science.gov (United States)

    Kim, Kwanpyo; Lee, Tae Hoon; Santos, Elton J G; Jo, Pil Sung; Salleo, Alberto; Nishi, Yoshio; Bao, Zhenan

    2015-06-23

    Graphene, with its unique electronic and structural qualities, has become an important playground for studying adsorption and assembly of various materials including organic molecules. Moreover, organic/graphene vertical structures assembled by van der Waals interaction have potential for multifunctional device applications. Here, we investigate structural and electrical properties of vertical heterostructures composed of C60 thin film on graphene. The assembled film structure of C60 on graphene is investigated using transmission electron microscopy, which reveals a uniform morphology of C60 film on graphene with a grain size as large as 500 nm. The strong epitaxial relations between C60 crystal and graphene lattice directions are found, and van der Waals ab initio calculations support the observed phenomena. Moreover, using C60-graphene heterostructures, we fabricate vertical graphene transistors incorporating n-type organic semiconducting materials with an on/off ratio above 3 × 10(3). Our work demonstrates that graphene can serve as an excellent substrate for assembly of molecules, and attained organic/graphene heterostructures have great potential for electronics applications.

  5. Gating of high-mobility InAs metamorphic heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Shabani, J. [California NanoSystems Institute, University of California, Santa Barbara, California 93106 (United States); McFadden, A. P. [Department of Electrical Engineering, University of California, Santa Barbara, California 93106 (United States); Shojaei, B. [Materials Department, University of California, Santa Barbara, California 93106 (United States); Palmstrøm, C. J. [California NanoSystems Institute, University of California, Santa Barbara, California 93106 (United States); Department of Electrical Engineering, University of California, Santa Barbara, California 93106 (United States); Materials Department, University of California, Santa Barbara, California 93106 (United States)

    2014-12-29

    We investigate the performance of gate-defined devices fabricated on high mobility InAs metamorphic heterostructures. We find that heterostructures capped with In{sub 0.75}Ga{sub 0.25}As often show signs of parallel conduction due to proximity of their surface Fermi level to the conduction band minimum. Here, we introduce a technique that can be used to estimate the density of this surface charge that involves cool-downs from room temperature under gate bias. We have been able to remove the parallel conduction under high positive bias, but achieving full depletion has proven difficult. We find that by using In{sub 0.75}Al{sub 0.25}As as the barrier without an In{sub 0.75}Ga{sub 0.25}As capping, a drastic reduction in parallel conduction can be achieved. Our studies show that this does not change the transport properties of the quantum well significantly. We achieved full depletion in InAlAs capped heterostructures with non-hysteretic gating response suitable for fabrication of gate-defined mesoscopic devices.

  6. Electron dynamics in MoS2-graphite heterostructures.

    Science.gov (United States)

    Zhang, Xinwu; He, Dawei; Yi, Lixin; Zhao, Siqi; He, Jiaqi; Wang, Yongsheng; Zhao, Hui

    2017-10-05

    The electron dynamics in heterostructures formed by multilayer graphite and monolayer or bulk MoS2 were studied by femtosecond transient absorption measurements. Samples of monolayer MoS2-multilayer graphite and bulk MoS2-multilayer graphite were fabricated by exfoliation and dry transfer techniques. Ultrafast laser pulses were used to inject electron-hole pairs into monolayer or bulk MoS2. The transfer of these photocarriers to the adjacent multilayer graphite was time resolved by measuring the differential reflection of a probe pulse. We found that photocarriers injected into monolayer MoS2 transfer to graphite on an ultrafast time scale shorter than 400 fs. Such an efficient charge transfer is key to the development of high performance optoelectronic devices with MoS2 as the light absorbing layer and graphite as electrodes. The absorption coefficient of monolayer MoS2 can be controlled by the carriers in graphite. This process can be used for interlayer coupling and control. In a bulk MoS2-graphite heterostructure, the photocarrier transfer time is about 220 ps, due to the inefficient interlayer charge transport in bulk MoS2. These results provide useful information for developing optoelectronic devices based on MoS2-graphite heterostructures.

  7. Evolutionary design of interfacial phase change van der Waals heterostructures.

    Science.gov (United States)

    Kalikka, Janne; Zhou, Xilin; Behera, Jitendra; Nannicini, Giacomo; Simpson, Robert E

    2016-10-27

    We use an evolutionary algorithm to explore the design space of hexagonal Ge 2 Sb 2 Te 5 ; a van der Waals layered two dimensional crystal heterostructure. The Ge 2 Sb 2 Te 5 structure is more complicated than previously thought. Predominant features include layers of Ge 3 Sb 2 Te 6 and Ge 1 Sb 2 Te 4 two dimensional crystals that interact through Te-Te van der Waals bonds. Interestingly, (Ge/Sb)-Te-(Ge/Sb)-Te alternation is a common feature for the most stable structures of each generation's evolution. This emergent rule provides an important structural motif that must be included in the design of high performance Sb 2 Te 3 -GeTe van der Waals heterostructure superlattices with interfacial atomic switching capability. The structures predicted by the algorithm agree well with experimental measurements on highly oriented, and single crystal Ge 2 Sb 2 Te 5 samples. By analysing the evolutionary algorithm optimised structures, we show that diffusive atomic switching is probable by Ge atoms undergoing a transition at the van der Waals interface from layers of Ge 3 Sb 2 Te 6 to Ge 1 Sb 2 Te 4 thus producing two blocks of Ge 2 Sb 2 Te 5 . Evolutionary methods present an efficient approach to explore the enormous multi-dimensional design parameter space of van der Waals bonded heterostructure superlattices.

  8. Franckeite as a naturally occurring van der Waals heterostructure

    Science.gov (United States)

    Molina-Mendoza, Aday J.; Giovanelli, Emerson; Paz, Wendel S.; Niño, Miguel Angel; Island, Joshua O.; Evangeli, Charalambos; Aballe, Lucía; Foerster, Michael; van der Zant, Herre S. J.; Rubio-Bollinger, Gabino; Agraït, Nicolás; Palacios, J. J.; Pérez, Emilio M.; Castellanos-Gomez, Andres

    2017-01-01

    The fabrication of van der Waals heterostructures, artificial materials assembled by individual stacking of 2D layers, is among the most promising directions in 2D materials research. Until now, the most widespread approach to stack 2D layers relies on deterministic placement methods, which are cumbersome and tend to suffer from poor control over the lattice orientations and the presence of unwanted interlayer adsorbates. Here, we present a different approach to fabricate ultrathin heterostructures by exfoliation of bulk franckeite which is a naturally occurring and air stable van der Waals heterostructure (composed of alternating SnS2-like and PbS-like layers stacked on top of each other). Presenting both an attractive narrow bandgap (<0.7 eV) and p-type doping, we find that the material can be exfoliated both mechanically and chemically down to few-layer thicknesses. We present extensive theoretical and experimental characterizations of the material's electronic properties and crystal structure, and explore applications for near-infrared photodetectors. PMID:28194037

  9. Synthetic Nanosheets of Natural van der Waals Heterostructures.

    Science.gov (United States)

    Banik, Ananya; Biswas, Kanishka

    2017-11-13

    Creation of new van der Waals heterostructures by stacking different two dimensional (2D) crystals on top of each other in a chosen sequence is the next challenge after the discovery of graphene, mono/few layer of h-BN, and transition-metal dichalcogenides. However, chemical syntheses of van der Waals heterostructures are rarer than the physical preparation techniques. Herein, we demonstrate the kinetic stabilization of 2D ultrathin heterostructure (ca. 1.13-2.35 nm thick) nanosheets of layered intergrowth SnBi 2 Te 4 , SnBi 4 Te 7 , and SnBi 6 Te 10 , which belong to the Sn m Bi 2n Te 3n+m homologous series, by a simple solution based synthesis. Few-layer nanosheets exhibit ultralow lattice thermal conductivity (κ lat ) of 0.3-0.5 W m -1  K -1 and semiconducting electron-transport properties with high carrier mobility. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Axial Ge/Si nanowire heterostructure tunnel FETs.

    Energy Technology Data Exchange (ETDEWEB)

    Dayeh, Shadi A. (Los Alamos National Laboratory); Gin, Aaron V.; Huang, Jian Yu; Picraux, Samuel Thomas (Los Alamos National Laboratory)

    2010-03-01

    Axial Ge/Si heterostructure nanowires (NWs) allow energy band-edge engineering along the axis of the NW, which is the charge transport direction, and the realization of asymmetric devices for novel device architectures. This work reports on two significant advances in the area of heterostructure NWs and tunnel FETs: (i) the realization of 100% compositionally modulated Si/Ge axial heterostructure NWs with lengths suitable for device fabrication and (ii) the design and implementation of Schottky barrier tunnel FETs on these NWs for high-on currents and suppressed ambipolar behavior. Initial prototype devices with 10 nm PECVD SiN{sub x} gate dielectric resulted in a very high current drive in excess of 100 {micro}A/{micro}m (I/{pi}D) and 10{sup 5} I{sub on}/I{sub off} ratios. Prior work on the synthesis of Ge/Si axial NW heterostructures through the VLS mechanism have resulted in axial Si/Si{sub 1-x}Ge{sub x} NW heterostructures with x{sub max} {approx} 0.3, and more recently 100% composition modulation was achieved with a solid growth catalyst. In this latter case, the thickness of the heterostructure cannot exceed few atomic layers due to the slow axial growth rate and concurrent radial deposition on the NW sidewalls leading to a mixture of axial and radial deposition, which imposes a big challenge for fabricating useful devices form these NWs in the near future. Here, we report the VLS growth of 100% doping and composition modulated axial Ge/Si heterostructure NWs with lengths appropriate for device fabrication by devising a growth procedure that eliminates Au diffusion on the NW sidewalls and minimizes random kinking in the heterostructure NWs as deduced from detailed microscopy analysis. Fig. 1 a shows a cross-sectional SEM image of epitaxial Ge/Si axial NW heterostructures grown on a Ge(111) surface. The interface abruptness in these Ge/Si heterostructure NWs is of the order of the NW diameter. Some of these NWs develop a crystallographic kink that is {approx

  11. Advanced carbon nanotubes functionalization

    Science.gov (United States)

    Setaro, A.

    2017-10-01

    Similar to graphene, carbon nanotubes are materials made of pure carbon in its sp2 form. Their extended conjugated π-network provides them with remarkable quantum optoelectronic properties. Frustratingly, it also brings drawbacks. The π-π stacking interaction makes as-produced tubes bundle together, blurring all their quantum properties. Functionalization aims at modifying and protecting the tubes while hindering π-π stacking. Several functionalization strategies have been developed to circumvent this limitation in order for nanotubes applications to thrive. In this review, we summarize the different approaches established so far, emphasizing the balance between functionalization efficacy and the preservation of the tubes’ properties. Much attention will be given to a functionalization strategy overcoming the covalent-noncovalent dichotomy and to the implementation of two advanced functionalization schemes: (a) conjugation with molecular switches, to yield hybrid nanosystems with chemo-physical properties that can be tuned in a controlled and reversible way, and; (b) plasmonic nanosystems, whose ability to concentrate and enhance the electromagnetic fields can be taken advantage of to enhance the optical response of the tubes.

  12. Dye-Sensitized Solar Cell Based on Polyaniline/Multiwalled Carbon Nanotubes Counter Electrode

    Directory of Open Access Journals (Sweden)

    Shaker Ebrahim

    2013-01-01

    Full Text Available This work presented the successful fabrication of dye-sensitized solar cell using polyaniline base (EB, multiwalled carbon nanotubes (MWCNTs, organic dye (rhodamine B or riboflavin, zinc oxide (ZnO, and indium tin oxide (ITO. The electrical properties of the resultant devices were investigated by measuring the current density voltage (-, capacitance voltage (-, and impedance measurements under both dark and illuminated conditions. The photovoltaic cell characteristics, that is, open circuit voltage (, short circuit current density (, and energy conversion efficiency (, were evaluated under illumination and were found to be 0.48 mA/cm2, 400 mV, and 0.224%, respectively, for ITO/EB-MWCNTs/ZnO-rhodamine B/ITO heterostructure. Using impedance spectra, it was found that the series resistances of this type of solar cell are 62 and 60 Ω under darkness and illumination, respectively.

  13. Enhanced Carbon Nanotube Ultracapacitors Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed innovation utilizes carbon nanotubes (CNTs) coated with pseudo-capacitive MnO2 material as nano-composite electrode and ionic electrolyte for the...

  14. Noble-Metal Chalcogenide Nanotubes

    Directory of Open Access Journals (Sweden)

    Nourdine Zibouche

    2014-10-01

    Full Text Available We explore the stability and the electronic properties of hypothetical noble-metal chalcogenide nanotubes PtS2, PtSe2, PdS2 and PdSe2 by means of density functional theory calculations. Our findings show that the strain energy decreases inverse quadratically with the tube diameter, as is typical for other nanotubes. Moreover, the strain energy is independent of the tube chirality and converges towards the same value for large diameters. The band-structure calculations show that all noble-metal chalcogenide nanotubes are indirect band gap semiconductors. The corresponding band gaps increase with the nanotube diameter rapidly approaching the respective pristine 2D monolayer limit.

  15. Carbon nanotubes: engineering biomedical applications.

    Science.gov (United States)

    Gomez-Gualdrón, Diego A; Burgos, Juan C; Yu, Jiamei; Balbuena, Perla B

    2011-01-01

    Carbon nanotubes (CNTs) are cylinder-shaped allotropic forms of carbon, most widely produced under chemical vapor deposition. They possess astounding chemical, electronic, mechanical, and optical properties. Being among the most promising materials in nanotechnology, they are also likely to revolutionize medicine. Among other biomedical applications, after proper functionalization carbon nanotubes can be transformed into sophisticated biosensing and biocompatible drug-delivery systems, for specific targeting and elimination of tumor cells. This chapter provides an introduction to the chemical and electronic structure and properties of single-walled carbon nanotubes, followed by a description of the main synthesis and post-synthesis methods. These sections allow the reader to become familiar with the specific characteristics of these materials and the manner in which these properties may be dependent on the specific synthesis and post-synthesis processes. The chapter ends with a review of the current biomedical applications of carbon nanotubes, highlighting successes and challenges. Copyright © 2011 Elsevier Inc. All rights reserved.

  16. Transparent, Conductive Carbon Nanotube Films

    National Research Council Canada - National Science Library

    Zhuangchun Wu; Zhihong Chen; Xu Du; Jonathan M. Logan; Jennifer Sippel; Maria Nikolou; Katalin Kamaras; John R. Reynolds; David B. Tanner; Arthur F. Hebard; Andrew G. Rinzler

    2004-01-01

    We describe a simple process for the fabrication of ultrathin, transparent, optically homogeneous, electrically conducting films of pure single-walled carbon nanotubes and the transfer of those films...

  17. A Novel Heterostructure of BiOI Nanosheets Anchored onto MWCNTs with Excellent Visible-Light Photocatalytic Activity

    Science.gov (United States)

    Li, Shijie; Hu, Shiwei; Xu, Kaibing; Jiang, Wei; Liu, Jianshe; Wang, Zhaohui

    2017-01-01

    Developing efficient visible-light-driven (VLD) photocatalysts for environmental decontamination has drawn significant attention in recent years. Herein, we have reported a novel heterostructure of multiwalled carbon nanotubes (MWCNTs) coated with BiOI nanosheets as an efficient VLD photocatalyst, which was prepared via a simple solvothermal method. The morphology and structure were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-Vis diffuse reflectance spectroscopy (DRS), and specific surface area measurements. The results showed that BiOI nanosheets were well deposited on MWCNTs. The MWCNTs/BiOI composites exhibited remarkably enhanced photocatalytic activity for the degradation of rhodamine B (RhB), methyl orange (MO), and para-chlorophenol (4-CP) under visible-light, compared with pure BiOI. When the MWCNTs content is 3 wt %, the MWCNTs/BiOI composite (3%M-Bi) achieves the highest activity, which is even higher than that of a mechanical mixture (3 wt % MWCNTs + 97 wt % BiOI). The superior photocatalytic activity is predominantly due to the strong coupling interface between MWCNTs and BiOI, which significantly promotes the efficient electron-hole separation. The photo-induced holes (h+) and superoxide radicals (O2−) mainly contribute to the photocatalytic degradation of RhB over 3%M-Bi. Therefore, the MWCNTs/BiOI composite is expected to be an efficient VLD photocatalyst for environmental purification. PMID:28336856

  18. A Novel Heterostructure of BiOI Nanosheets Anchored onto MWCNTs with Excellent Visible-Light Photocatalytic Activity

    Directory of Open Access Journals (Sweden)

    Shijie Li

    2017-01-01

    Full Text Available Developing efficient visible-light-driven (VLD photocatalysts for environmental decontamination has drawn significant attention in recent years. Herein, we have reported a novel heterostructure of multiwalled carbon nanotubes (MWCNTs coated with BiOI nanosheets as an efficient VLD photocatalyst, which was prepared via a simple solvothermal method. The morphology and structure were characterized by powder X-ray diffraction (XRD, scanning electron microscopy (SEM, transmission electron microscopy (TEM, UV-Vis diffuse reflectance spectroscopy (DRS, and specific surface area measurements. The results showed that BiOI nanosheets were well deposited on MWCNTs. The MWCNTs/BiOI composites exhibited remarkably enhanced photocatalytic activity for the degradation of rhodamine B (RhB, methyl orange (MO, and para-chlorophenol (4-CP under visible-light, compared with pure BiOI. When the MWCNTs content is 3 wt %, the MWCNTs/BiOI composite (3%M-Bi achieves the highest activity, which is even higher than that of a mechanical mixture (3 wt % MWCNTs + 97 wt % BiOI. The superior photocatalytic activity is predominantly due to the strong coupling interface between MWCNTs and BiOI, which significantly promotes the efficient electron-hole separation. The photo-induced holes (h+ and superoxide radicals (O2− mainly contribute to the photocatalytic degradation of RhB over 3%M-Bi. Therefore, the MWCNTs/BiOI composite is expected to be an efficient VLD photocatalyst for environmental purification.

  19. Carbon Nanotubes and Related Structures

    OpenAIRE

    Kingsuk Mukhopadhyay; Kanik Ram; K.U. Bhasker Rao

    2008-01-01

    Carbon nanotubes have attracted the fancy of many scientists world wide. The small dimensions,strength, and the remarkable physical properties of these structures make them a unique material with a whole range of promising applications. In this review, the structural aspects, the advantages and disadvantages of different for their procedures synthesis, the qualitative and quantitative estimation of carbon nanotubes by different analytical techniques, the present status on their applications a...

  20. Carbon nanotubes for coherent spintronics

    DEFF Research Database (Denmark)

    Kuemmeth, Ferdinand; Churchill, H O H; Herring, P K

    2010-01-01

    Carbon nanotubes bridge the molecular and crystalline quantum worlds, and their extraordinary electronic, mechanical and optical properties have attracted enormous attention from a broad scientific community. We review the basic principles of fabricating spin-electronic devices based on individual......, electrically-gated carbon nanotubes, and present experimental efforts to understand their electronic and nuclear spin degrees of freedom, which in the future may enable quantum applications....

  1. Selective functionalization of carbon nanotubes

    Science.gov (United States)

    Strano, Michael S. (Inventor); Usrey, Monica (Inventor); Barone, Paul (Inventor); Dyke, Christopher A. (Inventor); Tour, James M. (Inventor); Kittrell, W. Carter (Inventor); Hauge, Robert H. (Inventor); Smalley, Richard E. (Inventor)

    2009-01-01

    The present invention is directed toward methods of selectively functionalizing carbon nanotubes of a specific type or range of types, based on their electronic properties, using diazonium chemistry. The present invention is also directed toward methods of separating carbon nanotubes into populations of specific types or range(s) of types via selective functionalization and electrophoresis, and also to the novel compositions generated by such separations.

  2. Gold(I)-Alkanethiolate Nanotubes

    KAUST Repository

    Zhang, Yu Xin

    2009-12-28

    (Figure Presented) A solution approach to assembling Au(I) - alkanethiolates into nanotube structures at room temperature is presented, in which Au(I) cations and alkanethiolate ligands are coordinated into thin platelet forms that then evolve into an open tubular configuration (see figure). The organic-inorganic hybrid nature of the nanotubes, their ability to be modified, and their high stability make them of interest for practical applications. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA.

  3. Selectivity of quantum dot sensitized ZnO nanotube arrays for improved photocatalytic activity.

    Science.gov (United States)

    Gao, Ge; Xi, Qiaoyue; Zhou, Hua; Zhao, Yongxia; Wu, Cunqi; Wang, Lidan; Guo, Pengran; Xu, Jingwei

    2017-05-10

    In this work, PbS/ZnO, CdS/ZnO and CdSe/ZnO hierarchical heterostructures have been successfully synthesized by combining water bath and chemical bath deposition (CBD) methods on indium-doped tin oxide (ITO). Scanning electron microscopy (SEM) results show that quantum dots (QDs) certainly form on the pre-grown ZnO nanorod (NR) and nanotube (NT) arrays. The amount of QDs capped on ZnO could be regulated by varying the cycle times. The photocatalytic activity of the QD-sensitized ZnO is investigated by decomposition of methyl orange (MO) under irradiation, which show remarkable enhancement compared to bare ZnO. The ZnO NTs sensitized by PbS QDs have the highest catalytic activity among the three QDs (PbS, CdS and CdSe QDs). The UV-vis absorption diagrams and the Ct/C0 curves reveal that 8PbS/ZnO NTs have the highest catalytic activity, which can degrade MO (20 mg L(-1)) into a colorless solution within 30 min. Meanwhile, the synthetic methodology described herein provides an effective approach for fabricating a variety of photocatalysts. The heterostructured nanomaterials have significant potential to solve environmental and energy issues.

  4. Dynamics of exciton diffusion in poly(p-phenylene vinylene)/fullerene heterostructures

    NARCIS (Netherlands)

    Markov, D.E.; Hummelen, J.C.; Blom, P.W.M.; Sieval, A.B.

    The exciton diffusion process in a poly(p-phenylene vinylene)- (PPV-)based derivative is investigated using time-resolved photoluminescence in conjugated polymer/fullerene heterostructures. The decay of the luminescence in the polymer/fullerene heterostructures is governed by exciton diffusion and

  5. Interface engineering of CsPbI3-black phosphorus van der Waals heterostructure

    Science.gov (United States)

    Liu, Biao; Long, Mengqiu; Cai, Meng-Qiu; Yang, Junliang

    2018-01-01

    Interface Engineering is an effective route to tune structural and electrical properties in semiconductor heterostructures. Two kinds of typical van der Waals (vdW)-type electrical contacts, i.e., the electrical contacts of the Pb-I interface and Cs-I interface with a black phosphorus (BP) monolayer, respectively, in CsPbI3-BP heterostructures are studied by first-principles calculations. The electronic band structures of both CsPbI3 slabs and the BP monolayer are preserved in the combined vdW CsPbI3-BP heterostructures. The heterostructure of the Pb-I interface contacting with BP demonstrates the type-I band alignment, and the Cs-I interface contacting with the BP heterostructure demonstrates the type-II band alignment. The reason for the energy level shift is the work function difference of CsPbI3 slabs relative to the BP monolayer, which drives electrons and holes to move spontaneously. In addition, the CsPbI3-BP heterostructures show much better optical properties than CsPbI3 slabs. The light absorptions are enhanced in the CsPbI3-BP heterostructures, especially in the infrared region, which would improve the use of infrared light in CsPbI3 perovskite solar cells. This work suggests that such inorganic perovskite-BP heterostructures have significant potential for future optoelectronic applications and can enable broad possibilities with compositional tunability in inorganic perovskites.

  6. Page 1 i i ZnSe-GaAs heterostructures by MOVPE 357 Deep levels ...

    Indian Academy of Sciences (India)

    ZnSe-GaAs heterostructures by MOVPE 357. Deep levels in heterostructures often act as recombination and/or nonradiative centres and degrade their carrier transport and/or optical properties, We study the nature of deep traps in the HD by means of deep-level transient spectroscopy (DLTS), which provides a very ...

  7. PHOTOELECTRIC PROPERTIES OF HETEROSTRUCTURES BASED ON PEPC AND MEH-PPV FILMS DOPED WITH ZINC OCTABUTYLPHTHALOCYANINE

    Directory of Open Access Journals (Sweden)

    Nicolay Davidenko

    2016-06-01

    Full Text Available Planar organic heterostructures were prepared using poly-N- epoxypropylcarbazole films and poly[2-methoxy-5-(2’-ethylhexyloxy-1,4-phenylenevinylene] by the method of successive deposition adding 2,3,9,10,16,17,23,24-zinc octabutylphthalocyanine. Photoelectric, photodielectric and photovoltaic properties of the heterostructures were studied.

  8. Glucose oxidase immobilization onto carbon nanotube networking

    CERN Document Server

    Karachevtsev, V A; Zarudnev, E S; Karachevtsev, M V; Leontiev, V S; Linnik, A S; Lytvyn, O S; Plokhotnichenko, A M; Stepanian, S G

    2012-01-01

    When elaborating the biosensor based on single-walled carbon nanotubes (SWNTs), it is necessary to solve such an important problem as the immobilization of a target biomolecule on the nanotube surface. In this work, the enzyme (glucose oxidase (GOX)) was immobilized on the surface of a nanotube network, which was created by the deposition of nanotubes from their solution in 1,2-dichlorobenzene by the spray method. 1-Pyrenebutanoic acid succinimide ester (PSE) was used to form the molecular interface, the bifunctional molecule of which provides the covalent binding with the enzyme shell, and its other part (pyrene) is adsorbed onto the nanotube surface. First, the usage of such a molecular interface leaves out the direct adsorption of the enzyme (in this case, its activity decreases) onto the nanotube surface, and, second, it ensures the enzyme localization near the nanotube. The comparison of the resonance Raman (RR) spectrum of pristine nanotubes with their spectrum in the PSE environment evidences the creat...

  9. Polymer nanotube nanocomposites: synthesis, properties, and applications

    National Research Council Canada - National Science Library

    Mittal, Vikas

    2010-01-01

    ... in these commercially important areas of polymer technology. It sums up recent advances in nanotube composite synthesis technology, provides basic introduction to polymer nanotubes nanocomposite technology for the readers new to this field, provides valuable...

  10. Probing Photosensitization by Functionalized Carbon Nanotubes

    Science.gov (United States)

    Carbon nanotubes (CNTs) photosensitize the production of reactive oxygen species that can damage organisms by biomembrane oxidation or mediate CNTs' environmental transformations. The photosensitized nature of derivatized carbon nanotubes from various synthetic methods, and thus ...

  11. Effects of morphology and surface area of the oxide nanostructures on the visible-light induced generation of hydrogen in ZnO(TiO2)/Cd1 - xZnxS and ZnO(TiO2)/Pt/Cd1 - xZnxS heterostructures (x = 0.0, 0.2)

    Science.gov (United States)

    Roy, Anand; Lingampalli, S. R.; Saha, Sujoy; Rao, C. N. R.

    2015-09-01

    Hydrogen can be generated by visible light irradiation of semiconductor heterostructures of the type ZnO/Pt/CdS and TiO2/Pt/CdS. In order to understand the dependence of hydrogen generation on the properties of the nanoparticles of ZnO and TiO2, we have carried out systematic studies. For this purpose, we have studied photocatalytic hydrogen generation by ZnO(TiO2)/Cd1 - xZnxS and ZnO(TiO2)/Pt/Cd1 - xZnxS (x = 0.0, 0.2) heterostructures with oxide nanostructures possessing different morphologies and surface areas. In the case of TiO2/Pt/Cd0.8Zn0.2S heterostructures, the highest H2 evolution rate up to1.76 mmol h-1 g-1 were obtained with H2Ti3O7 nanotubes, with the least H2 evolution rate (0.55 mmol h-1 g-1) from TiO2 powder (Degussa P25). In the case of ZnO/Pt/CdS heterostructures, the highest H2 evolution rate (6.88 mmol h-1 g-1) were obtained from ZnO nanorods1, whereas the least H2 evolution rate (2.55 mmol h-1 g-1) was obtained from ZnO nanorods3. The photocatalytic activity of heterostructures generally follows the trend in BET surface areas of the oxide nanostructures, with high surface area favoring good hydrogen evolution activity.

  12. Carbon nanotube biosensors

    Science.gov (United States)

    Tîlmaciu, Carmen-Mihaela; Morris, May C.

    2015-01-01

    Nanomaterials possess unique features which make them particularly attractive for biosensing applications. In particular, carbon nanotubes (CNTs) can serve as scaffolds for immobilization of biomolecules at their surface, and combine several exceptional physical, chemical, electrical, and optical characteristics properties which make them one of the best suited materials for the transduction of signals associated with the recognition of analytes, metabolites, or disease biomarkers. Here we provide a comprehensive review on these carbon nanostructures, in which we describe their structural and physical properties, functionalization and cellular uptake, biocompatibility, and toxicity issues. We further review historical developments in the field of biosensors, and describe the different types of biosensors which have been developed over time, with specific focus on CNT-conjugates engineered for biosensing applications, and in particular detection of cancer biomarkers. PMID:26579509

  13. Carbon Nanotube Biosensors

    Science.gov (United States)

    Tilmaciu, Carmen-Mihaela; Morris, May

    2015-10-01

    Nanomaterials possess unique features which make them particularly attractive for biosensing applications. In particular Carbon Nanotubes (CNTs) can serve as scaffolds for immobilization of biomolecules at their surface, and combine several exceptional physical, chemical, electrical and optical characteristics properties which make them one of the best suited materials for the transduction of signals associated with the recognition of analytes, metabolites or disease biomarkers. Here we provide a comprehensive review on these carbon nanostructures, in which we will describe their structural and physical properties, discuss functionalization and cellular uptake, biocompatibility and toxicity issues. We further review historical developments in the field of biosensors, and describe the different types of biosensors which have been developed over time, with specific focus on CNT-conjugates engineered for biosensing applications, and in particular detection of cancer biomarkers.

  14. Carbon Nanotube Electron Gun

    Science.gov (United States)

    Nguyen, Cattien V. (Inventor); Ribaya, Bryan P. (Inventor)

    2013-01-01

    An electron gun, an electron source for an electron gun, an extractor for an electron gun, and a respective method for producing the electron gun, the electron source and the extractor are disclosed. Embodiments provide an electron source utilizing a carbon nanotube (CNT) bonded to a substrate for increased stability, reliability, and durability. An extractor with an aperture in a conductive material is used to extract electrons from the electron source, where the aperture may substantially align with the CNT of the electron source when the extractor and electron source are mated to form the electron gun. The electron source and extractor may have alignment features for aligning the electron source and the extractor, thereby bringing the aperture and CNT into substantial alignment when assembled. The alignment features may provide and maintain this alignment during operation to improve the field emission characteristics and overall system stability of the electron gun.

  15. Carbon Nanotube Biosensors

    Directory of Open Access Journals (Sweden)

    Carmen-Mihaela eTilmaciu

    2015-10-01

    Full Text Available Nanomaterials possess unique features which make them particularly attractive for biosensing applications. In particular Carbon Nanotubes (CNTs can serve as scaffolds for immobilization of biomolecules at their surface, and combine several exceptional physical, chemical, electrical and optical characteristics properties which make them one of the best suited materials for the transduction of signals associated with the recognition of analytes, metabolites or disease biomarkers. Here we provide a comprehensive review on these carbon nanostructures, in which we will describe their structural and physical properties, discuss functionalization and cellular uptake, biocompatibility and toxicity issues. We further review historical developments in the field of biosensors, and describe the different types of biosensors which have been developed over time, with specific focus on CNT-conjugates engineered for biosensing applications, and in particular detection of cancer biomarkers.

  16. Gate-Tunable Spin Transport and Giant Electroresistance in Ferromagnetic Graphene Vertical Heterostructures

    Science.gov (United States)

    Myoung, Nojoon; Park, Hee Chul; Lee, Seung Joo

    2016-04-01

    Controlling tunneling properties through graphene vertical heterostructures provides advantages in achieving large conductance modulation which has been known as limitation in lateral graphene device structures. Despite of intensive research on graphene vertical heterosturctures for recent years, the potential of spintronics based on graphene vertical heterostructures remains relatively unexplored. Here, we present an analytical device model for graphene-based spintronics by using ferromagnetic graphene in vertical heterostructures. We consider a normal or ferroelectric insulator as a tunneling layer. The device concept yields a way of controlling spin transport through the vertical heterostructures, resulting in gate-tunable spin-switching phenomena. Also, we revealed that a ‘giant’ resistance emerges through a ferroelectric insulating layer owing to the anti-parallel configuration of ferromagnetic graphene layers by means of electric fields via gate and bias voltages. Our findings discover the prospect of manipulating the spin transport properties in vertical heterostructures without use of magnetic fields.

  17. Inner- and outer-wall sorting of double-walled carbon nanotubes

    Science.gov (United States)

    Li, Han; Gordeev, Georgy; Wasserroth, Sören; Chakravadhanula, Venkata Sai Kiran; Neelakandhan, Shyam Kumar Chethala; Hennrich, Frank; Jorio, Ado; Reich, Stephanie; Krupke, Ralph; Flavel, Benjamin Scott

    2017-12-01

    Double-walled carbon nanotubes (DWCNTs) consist of two coaxially aligned single-walled carbon nanotubes (SWCNTs), and previous sorting methods only achieved outer-wall electronic-type selectivity. Here, a separation technique capable of sorting DWCNTs by semiconducting (S) or metallic (M) inner- and outer-wall electronic type is presented. Electronic coupling between the inner and outer wall is used to alter the surfactant coating around each of the DWCNT types, and aqueous gel permeation is used to separate them. Aqueous methods are used to remove SWCNT species from the raw material and prepare enriched DWCNT fractions. The enriched DWCNT fractions are then transferred into either chlorobenzene or toluene using the copolymer PFO-BPy to yield the four inner@outer combinations of M@M, M@S, S@M and S@S. The high purity of the resulting fractions is verified by absorption measurements, transmission electron microscopy, atomic force microscopy, resonance Raman mapping and high-density field-effect transistor devices.

  18. Development and characterization of coaxially electrospun gelatin coated poly (3-hydroxybutyric acid) thin films as potential scaffolds for skin regeneration

    Energy Technology Data Exchange (ETDEWEB)

    Nagiah, Naveen [Bioproducts Lab, Central Leather Research Institute, Adyar, Chennai (India); Madhavi, Lakshmi; Anitha, R. [CavinKare Research Centre, Ekkattuthangal, Chennai (India); Anandan, C. [National Aerospace Laboratory, Banglore (India); Srinivasan, Natarajan Tirupattur, E-mail: naveen.nagiah@gmail.com [Conducting Polymers Lab, Department of Physics, Indian Institute of Technology Madras, Chennai (India); Sivagnanam, Uma Tirichurapalli, E-mail: suma67@gmail.com [Bioproducts Lab, Central Leather Research Institute, Adyar, Chennai (India)

    2013-10-01

    The morphology of fibers synthesized through electrospinning has been found to mimic extracellular matrix. Coaxially electrospun fibers of gelatin (sheath) coated poly (3-hydroxybutyric acid) (PHB) (core) was developed using 2,2,2 trifluoroethanol(TFE) and 1,1,1,3,3,3 hexafluoro-2-propanol(HFIP) as solvents respectively. The coaxial structure and coating of gelatin with PHB fibers was confirmed through transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). Thermal stability of the coaxially electrospun fibers was analyzed using thermogravimetric analysis(TGA), differential scanning calorimetry(DSC) and differential thermogravimetric analysis(DTA). Complete evaporation of solvent and gelatin grafting over PHB fibers was confirmed through attenuated total reflection-Fourier transformed infrared spectroscopy (ATR-FTIR). The coaxially electrospun fibers exhibited competent tensile properties for skin regeneration with high surface area and porosity. In vitro degradation studies proved the stability of fibers and its potential applications in tissue engineering. The fibers supported the growth of human dermal fibroblasts and keratinocytes with normal morphology indicating its potential as a scaffold for skin regeneration. - Highlights: • Coaxial electrospinning was employed to develop core-shell fibers of PHB and gelatin. • The scaffold has competent physicochemical properties. • Developed scaffold will have high impact as a dermal substitute in skin regeneration.

  19. Dispersions of Carbon nanotubes in Polymer Matrices

    Science.gov (United States)

    Wise, Kristopher Eric (Inventor); Park, Cheol (Inventor); Siochi, Emilie J. (Inventor); Harrison, Joycelyn S. (Inventor); Lillehei, Peter T. (Inventor); Lowther, Sharon E. (Inventor)

    2010-01-01

    Dispersions of carbon nanotubes exhibiting long term stability are based on a polymer matrix having moieties therein which are capable of a donor-acceptor complexation with carbon nanotubes. The carbon nanotubes are introduced into the polymer matrix and separated therein by standard means. Nanocomposites produced from these dispersions are useful in the fabrication of structures, e.g., lightweight aerospace structures.

  20. Nanotubes in Nanoelectronics: Transport, Growth and Modeling

    Science.gov (United States)

    Anantram, M.; Delzeit, Lance; Cassell, Alan; Han, Jie; Meyyappan, M.; Arnold, Jim (Technical Monitor)

    2001-01-01

    Carbon nanotube (CNT) baud nanotechnology appears to be promising for future Theoretical analysis and results for the ballistic current carrying capacity of nanotube wires am presented. Aspects of metal-nanotube coupling are examined. Results am also presented for chemical vapor deposition of CNT from hydrocarbon feedstock.

  1. Design of catheter radio frequency coils using coaxial transmission line resonators for interventional neurovascular MR imaging.

    Science.gov (United States)

    Zhang, Xiaoliang; Martin, Alastair; Jordan, Caroline; Lillaney, Prasheel; Losey, Aaron; Pang, Yong; Hu, Jeffrey; Wilson, Mark; Cooke, Daniel; Hetts, Steven W

    2017-04-01

    It is technically challenging to design compact yet sensitive miniature catheter radio frequency (RF) coils for endovascular interventional MR imaging. In this work, a new design method for catheter RF coils is proposed based on the coaxial transmission line resonator (TLR) technique. Due to its distributed circuit, the TLR catheter coil does not need any lumped capacitors to support its resonance, which simplifies the practical design and construction and provides a straightforward technique for designing miniature catheter-mounted imaging coils that are appropriate for interventional neurovascular procedures. The outer conductor of the TLR serves as an RF shield, which prevents electromagnetic energy loss, and improves coil Q factors. It also minimizes interaction with surrounding tissues and signal losses along the catheter coil. To investigate the technique, a prototype catheter coil was built using the proposed coaxial TLR technique and evaluated with standard RF testing and measurement methods and MR imaging experiments. Numerical simulation was carried out to assess the RF electromagnetic field behavior of the proposed TLR catheter coil and the conventional lumped-element catheter coil. The proposed TLR catheter coil was successfully tuned to 64 MHz for proton imaging at 1.5 T. B1 fields were numerically calculated, showing improved magnetic field intensity of the TLR catheter coil over the conventional lumped-element catheter coil. MR images were acquired from a dedicated vascular phantom using the TLR catheter coil and also the system body coil. The TLR catheter coil is able to provide a significant signal-to-noise ratio (SNR) increase (a factor of 200 to 300) over its imaging volume relative to the body coil. Catheter imaging RF coil design using the proposed coaxial TLR technique is feasible and advantageous in endovascular interventional MR imaging applications.

  2. Pneumothorax Complicating Coaxial and Non-coaxial CT-Guided Lung Biopsy: Comparative Analysis of Determining Risk Factors and Management of Pneumothorax in a Retrospective Review of 650 Patients.

    Science.gov (United States)

    Nour-Eldin, Nour-Eldin A; Alsubhi, Mohammed; Emam, Ahmed; Lehnert, Thomas; Beeres, Martin; Jacobi, Volkmar; Gruber-Rouh, Tatjana; Scholtz, Jan-Erik; Vogl, Thomas J; Naguib, Nagy N

    2016-02-01

    To assess the scope and determining risk factors related to the development of pneumothorax throughout CT-guided biopsy of pulmonary lesions in coaxial and non-coaxial techniques and the outcome of its management. The study included CT-guided percutaneous lung biopsies in 650 consecutive patients (407 males, 243 females; mean age 54.6 years, SD 5.2) from November 2008 to June 2013 in a retrospective design. Patients were classified according to lung biopsy technique into coaxial group (318 lesions) and non-coaxial group (332 lesions). Exclusion criteria for biopsy were lesions respiratory compromise, pulmonary arterial hypertension, or refusal of the procedure. Risk factors related to the occurrence of pneumothorax were classified into: (a) Technical risk factors, (b) patient-related risk factors, and (c) lesion-associated risk factors. Radiological assessments were performed by two radiologists in consensus. Mann-Whitney U test and Fisher's exact tests were used for statistical analysis. p values Manual evacuation of pneumothorax was efficient in 44/51 patients (86.3 %) in both groups and intercostal chest tube was applied after failure of manual evacuation (7 patients: 13.7 %), from which one patient developed a persistent air leakage necessitating pleurodesis. Pneumothorax complicating CT-guided core biopsy of pulmonary lesions, showed the insignificant difference between coaxial and non-coaxial techniques. However, both techniques have the same significant risk factors including small and basal lesions, increased lesion's depth from pleural surface, and increased length of aerated lung parenchyma crossed by biopsy needle and passing through pulmonary fissures in the needle tract.

  3. Experimental Investigation of the Fresnel Drag Effect in RF Coaxial Cables

    Directory of Open Access Journals (Sweden)

    Brotherton D.

    2011-01-01

    Full Text Available An experiment that confirms the Fresnel drag formalism in RF coaxial cables is reported. The Fresnel "drag" in bulk dielectrics and in optical fibers has previously been well established. An explanation for this formalism is given, and it is shown that there is no actual drag phenomenon, rather that the Fresnel drag effect is merely the consequence of a simplified description of EM scattering within a dielectric in motion wrt the dynamical 3-space. The Fresnel drag effect plays a critical role in the design of various light-speed anisotropy detectors.

  4. Experimental Investigation of the Fresnel Drag Effect in RF Coaxial Cables

    Directory of Open Access Journals (Sweden)

    Cahill R. T.

    2011-01-01

    Full Text Available An experiment that confirms the Fresnel drag formalism in RF coaxial cables is re- ported. The Fresnel ‘drag’ in bulk dielectrics and in optical fibers has previously been well established. An explanation for this formalism is given, and it is shown that there is no actual drag phenomenon, rather that the Fresnel drag effect is merely the conse- quence of a simplified description of EM scattering within a dielectric in motion wrt the dynamical 3-space. The Fresnel drag effect plays a critical role in the design of various light-speed anisotropy detectors.

  5. Superluminal X-shaped beams propagating without distortion along a coaxial guide.

    Science.gov (United States)

    Zamboni-Rached, Michel; Nóbrega, K Z; Recami, Erasmo; Hernández-Figueroa, Hugo Enrique

    2002-10-01

    In a previous paper we showed that localized superluminal solutions to the Maxwell equations exist, which propagate down (nonevanescence) regions of a metallic cylindrical waveguide. In this paper we construct analogous nondispersive waves propagating along coaxial cables. Such new solutions, in general, consist in trains of (undistorted) superluminal "X-shaped" pulses. Particular attention is paid to the construction of finite total energy solutions. Any results of this kind may find application in the other fields in which an essential role is played by a wave equation (like acoustics, geophysics, etc.).

  6. Testing and optimizing MST coaxial collinear arrays, part 6.4A

    Science.gov (United States)

    Warnock, J. M.; Green, J. L.

    1984-01-01

    Many clear-air VHF wind profiles use coaxial collinear (COCO) arrays for their antenna. A COCO array is composed of long lines of half-wave dipoles spaced one-half wavelength apart. An inexpensive method of checking a COCO array is described and its performance is optimized by measuring and then correcting the relative rf phase among its lines at their feed point. This method also gives an estimate of the rf current amplitude among the lines. The strength and location of the sidelobes in the H-plane of the array can be estimated.

  7. High-precision efficiency calibration of a high-purity co-axial germanium detector

    Energy Technology Data Exchange (ETDEWEB)

    Blank, B., E-mail: blank@cenbg.in2p3.fr [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Souin, J.; Ascher, P.; Audirac, L.; Canchel, G.; Gerbaux, M.; Grévy, S.; Giovinazzo, J.; Guérin, H.; Nieto, T. Kurtukian; Matea, I. [Centre d' Etudes Nucléaires de Bordeaux Gradignan, UMR 5797, CNRS/IN2P3, Université de Bordeaux, Chemin du Solarium, BP 120, 33175 Gradignan Cedex (France); Bouzomita, H.; Delahaye, P.; Grinyer, G.F.; Thomas, J.C. [Grand Accélérateur National d' Ions Lourds, CEA/DSM, CNRS/IN2P3, Bvd Henri Becquerel, BP 55027, F-14076 CAEN Cedex 5 (France)

    2015-03-11

    A high-purity co-axial germanium detector has been calibrated in efficiency to a precision of about 0.15% over a wide energy range. High-precision scans of the detector crystal and γ-ray source measurements have been compared to Monte-Carlo simulations to adjust the dimensions of a detector model. For this purpose, standard calibration sources and short-lived online sources have been used. The resulting efficiency calibration reaches the precision needed e.g. for branching ratio measurements of super-allowed β decays for tests of the weak-interaction standard model.

  8. Magnetic insulation in triplate and coaxial vacuum transmission lines. Report PIFR-1009

    Energy Technology Data Exchange (ETDEWEB)

    Di Capua, M.; Pellinen, D.G.

    1980-08-01

    An experimental investigation was made of magnetically insulated transmission lines for use in an electron beam fusion accelerator. The magnetically insulated vacuum transmission lines would transfer the power pulses from many modules to a single diode region or multiple diodes to generate currents on the order of 100 MA. This approach may allow present limits on power flow through dielectric vacuum interfaces to be overcome. We have investigated symmetric parallel plate (triplate) transmission lines with a wave impedance of 24 ..cap omega.. and a spacing of 1.9 cm, and coaxial transmission lines (coax) with a wave impedance of 42 ..cap omega.. and a spacing of 2.9 cm.

  9. Electrode surface rf harmonics generated by the nonlinear sheath in a coaxial capacitive rf discharge

    Energy Technology Data Exchange (ETDEWEB)

    Savas, S.E. (Applied Materials, Santa Clara, CA (USA))

    1989-07-01

    rf harmonics of the 13.56 MHz excitation signal have been measured on the electrode surface in a large coaxial capacitive discharge. These are seen to have from 10% of the fundamental amplitude for the second harmonic to between 1% and 4% for the third and fourth harmonics. There is evidence that these modes propragate as TEM surface waves (Gould-Trivelpiece modes) along the length of the electrode. The Telegrapher's equations can be written for the system with non-constant shunt capacitance and admittance. The resulting nonlinear equation for the sheath voltage is solved for the harmonics to yield approximate agreement with their observed magnitudes.

  10. New mode of operating a magnetized coaxial plasma gun for injecting magnetic helicity into a spheromak.

    Science.gov (United States)

    Woodruff, S; Hill, D N; Stallard, B W; Bulmer, R; Cohen, B; Holcomb, C T; Hooper, E B; McLean, H S; Moller, J; Wood, R D

    2003-03-07

    By operating a magnetized coaxial plasma gun continuously with just sufficient current to enable plasma ejection, large gun-voltage spikes (approximately 1 kV) are produced, giving the highest sustained voltage approximately 500 V and highest sustained helicity injection rate observed in the Sustained Spheromak Physics Experiment. The spheromak magnetic field increases monotonically with time, exhibiting the lowest fluctuation levels observed during formation of any spheromak (B/B>/=2%). The results suggest an important mechanism for field generation by helicity injection, namely, the merging of helicity-carrying filaments.

  11. Synthesis method for ultrananocrystalline diamond in powder employing a coaxial arc plasma gun

    Science.gov (United States)

    Naragino, Hiroshi; Tominaga, Aki; Hanada, Kenji; Yoshitake, Tsuyoshi

    2015-07-01

    A new method that enables us to synthesize ultrananocrystalline diamond (UNCD) in powder is proposed. Highly energetic carbon species ejected from a graphite cathode of a coaxial arc plasma gun were provided on a quartz plate at a high density by repeated arc discharge in a compact vacuum chamber, and resultant films automatically peeled from the plate were aggregated and powdered. The grain size was easily controlled from 2.4 to 15.0 nm by changing the arc discharge energy. It was experimentally demonstrated that the proposed method is a new and promising method that enables us to synthesize UNCD in powder easily and controllably.

  12. Exergoeconomic optimization of coaxial tube evaporators for cooling of high pressure gaseous hydrogen during vehicle fuelling

    DEFF Research Database (Denmark)

    Jensen, Jonas Kjær; Rothuizen, Erasmus Damgaard; Markussen, Wiebke Brix

    2014-01-01

    Gaseous hydrogen as an automotive fuel is reaching the point of commercial introduction. Development of hydrogen fuelling stations considering an acceptable fuelling time by cooling the hydrogen to -40 C has started. This paper presents a design study of coaxial tube ammonia evaporators for three...... different concepts of hydrogen cooling, one onestage and two two-stage processes. An exergoeconomic optimization is imposed to all three concepts to minimize the total cost. A numerical heat transfer model is developed in Engineer Equation Solver, using heat transfer and pressure drop correlations from...

  13. Alpha-event and surface characterisation in segmented true-coaxial HPGe detectors

    Energy Technology Data Exchange (ETDEWEB)

    Abt, I.; Garbini, L., E-mail: luciagarbini86@gmail.com.mpg.de; Gooch, C.; Irlbeck, S.; Liu, X.; Palermo, M.; Schulz, O.

    2017-06-21

    A detailed study of alpha interactions on the passivation layer on the end-plate of a true-coaxial high-purity germanium detector is presented. The observation of alpha events on such a surface indicates an unexpectedly thin so-called “effective dead layer” of less than 20 µm thickness. In addition, the influence of the metalisation close to the end-plate on the time evolution of the output pulses is discussed. The results indicate that alpha contamination can result in events which could be mistaken as signals for neutrinoless double beta decay and provide some guidance on how to prevent this.

  14. A Novel Coaxial Magnetic Gear and Its Integration With Permanent-Magnet Brushless Motor

    DEFF Research Database (Denmark)

    Zhang, Xiaoxu; Liu, Xiao; Chen, Zhe

    2016-01-01

    magnetic gear (CMG), which will not increase the mechanical complexity after integration with a permanent magnet (PM) brushless machine. The prominent feature of the proposed CMG is the introduction of the stator with modulating teeth, which function as the same as the modulating pole......A magnetic geared machine (MGM) is believed to be a promising candidate for high-torque direct-drive application. One of the key issues for developing MGMs is how to resolve the contradiction between the good performance and the complex structure. This paper aims at proposing a novel coaxial...

  15. Optical fiber-based core-shell coaxially structured hybrid cells for self-powered nanosystems

    Energy Technology Data Exchange (ETDEWEB)

    Pan, Caofeng; Zhu, Guang [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); Guo, Wenxi [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); State Key Laboratory of Physical Chemistry of Solid Surfaces, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Dong, Lin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); School of Materials Science and Enginnering, Zhenzhou University, Zhenghou 450001 (China); Wang, Zhong Lin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, Georgia (United States); Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, Beijing (China)

    2012-07-03

    An optical fiber-based 3D hybrid cell consisting of a coaxially structured dye-sensitized solar cell (DSSC) and a nanogenerator (NG) for simultaneously or independently harvesting solar and mechanical energy is demonstrated. The current output of the hybrid cell is dominated by the DSSC, and the voltage output is dominated by the NG; these can be utilized complementarily for different applications. The output of the hybrid cell is about 7.65 {mu}A current and 3.3 V voltage, which is strong enough to power nanodevices and even commercial electronic components. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. The Flow Separation of Peristaltic Transport for Maxwell Fluid between Two Coaxial Tubes

    Directory of Open Access Journals (Sweden)

    S. Z. A. Husseny

    2014-01-01

    Full Text Available We study the peristaltic mechanism of an incompressible non-Newtonian biofluid (namely, Maxwell model in the annular region between two coaxial tubes. The inner tube represents the endoscope tube. The system of the governing nonlinear PDE is solved by using the perturbation method to the first order in dimensionless wavenumber. The modified Newton-Raphson method is used to predict the flow separation points along the peristaltic wall and the endoscope tube. The results show that the presence of the endoscope (catheter tube in the artery increases the pressure gradient and shear stress. Such a result seems too reasonable from the physical and medical point of view.

  17. Resonant Tunneling in Photonic Double Quantum Well Heterostructures

    Directory of Open Access Journals (Sweden)

    Cox Joel

    2010-01-01

    Full Text Available Abstract Here, we study the resonant photonic states of photonic double quantum well (PDQW heterostructures composed of two different photonic crystals. The heterostructure is denoted as B/A/B/A/B, where photonic crystals A and B act as photonic wells and barriers, respectively. The resulting band structure causes photons to become confined within the wells, where they occupy discrete quantized states. We have obtained an expression for the transmission coefficient of the PDQW heterostructure using the transfer matrix method and have found that resonant states exist within the photonic wells. These resonant states occur in split pairs, due to a coupling between degenerate states shared by each of the photonic wells. It is observed that when the resonance energy lies at a bound photonic state and the two photonic quantum wells are far away from each other, resonant states appear in the transmission spectrum of the PDQW as single peaks. However, when the wells are brought closer together, coupling between bound photonic states causes an energy-splitting effect, and the transmitted states each have two peaks. Essentially, this means that the system can be switched between single and double transparent states. We have also observed that the total number of resonant states can be controlled by varying the width of the photonic wells, and the quality factor of transmitted peaks can be drastically improved by increasing the thickness of the outer photonic barriers. It is anticipated that the resonant states described here can be used to develop new types of photonic-switching devices, optical filters, and other optoelectronic devices.

  18. Measurements of acoustic particle velocity in a coaxial duct and its application to a traveling-wave thermoacoustic heat engine.

    Science.gov (United States)

    Morii, Jun; Biwa, Tetsushi; Yazaki, Taichi

    2014-09-01

    We present theoretical solutions, based on linear acoustic theory, for axial acoustic particle velocity in an annular region of a coaxial duct. The solutions are expressed in terms of two non-dimensional parameters h/δ(ν) and R; h and δ(ν), respectively, represent the half of the spacing between two concentric ducts and the characteristic length given by kinematic viscosity of the gas and angular frequency of acoustic oscillations, and R is the radius ratio of the ducts. The validity of the solutions was verified by direct measurements using a laser Doppler velocimeter. The present results are applied to measurements of the acoustic power distribution in a traveling wave thermoacoustic engine with a coaxial duct, which provides experimental evidence for acoustic power feedback in the coaxial duct.

  19. Characterisation of Low Frequency Gravitational Waves from Dual RF Coaxial-Cable Detector: Fractal Textured Dynamical 3-Space

    Directory of Open Access Journals (Sweden)

    Cahill R. T.

    2012-07-01

    Full Text Available Experiments have revealed that the Fresnel drag effect is not present in RF coaxial cables, contrary to a previous report. This enables a very sensitive, robust and compact detector, that is 1st order in v / c and using one clock, to detect the dynamical space passing the earth, revealing the sidereal rotation of the earth, together with significant wave / turbulence e ff ects. These are “gravitational waves”, and previously detected by Cahill 2006, using an Optical-Fibre – RF Coaxial Cable Detector, and Cahill 2009, using a preliminary version of the Dual RF Coaxial Cable Detector. The gravitational waves have a 1 / f spectrum, implying a fractal structure to the textured dynamical 3- space.

  20. Patenting activity in synthesis of lipid nanotubes and peptide nanotubes.

    Science.gov (United States)

    Zhou, Yong

    2007-01-01

    Lipid nanotubes (LNTs) and peptide nanotubes (PNTs) are especially intriguing and noncovalent self-assemblies of amphiphiles. They have hydrophilically internal and external membrane surfaces, and can provide the wide scope for chemical modifications, in sharp contrast to carbon nanotubes. These unique properties make themselves as ideal candidates for a variety of applications in chemistry, biochemistry, materials science and medicine. Patenting the LNTs and PNTs is quite active recently. This mini-review provides a brief outline of patenting activity in synthesis of the LNTs and PNTs since 1980s. The key point of the present review aims to create an optimistic circulation between the basic research achievement and potential application of this sub-field of nanotechnology, promoting each other in their future development.

  1. EDITORIAL: Focus on Carbon Nanotubes

    Science.gov (United States)

    2003-09-01

    The study of carbon nanotubes, since their discovery by Iijima in 1991, has become a full research field with significant contributions from all areas of research in solid-state and molecular physics and also from chemistry. This Focus Issue in New Journal of Physics reflects this active research, and presents articles detailing significant advances in the production of carbon nanotubes, the study of their mechanical and vibrational properties, electronic properties and optical transitions, and electrical and transport properties. Fundamental research, both theoretical and experimental, represents part of this progress. The potential applications of nanotubes will rely on the progress made in understanding their fundamental physics and chemistry, as presented here. We believe this Focus Issue will be an excellent guide for both beginners and experts in the research field of carbon nanotubes. It has been a great pleasure to edit the many excellent contributions from Europe, Japan, and the US, as well from a number of other countries, and to witness the remarkable effort put into the manuscripts by the contributors. We thank all the authors and referees involved in the process. In particular, we would like to express our gratitude to Alexander Bradshaw, who invited us put together this Focus Issue, and to Tim Smith and the New Journal of Physics staff for their extremely efficient handling of the manuscripts. Focus on Carbon Nanotubes Contents Transport theory of carbon nanotube Y junctions R Egger, B Trauzettel, S Chen and F Siano The tubular conical helix of graphitic boron nitride F F Xu, Y Bando and D Golberg Formation pathways for single-wall carbon nanotube multiterminal junctions Inna Ponomareva, Leonid A Chernozatonskii, Antonis N Andriotis and Madhu Menon Synthesis and manipulation of carbon nanotubes J W Seo, E Couteau, P Umek, K Hernadi, P Marcoux, B Lukic, Cs Mikó, M Milas, R Gaál and L Forró Transitional behaviour in the transformation from active end

  2. Molecular capture in protein nanotubes.

    Science.gov (United States)

    Qu, Xue; Komatsu, Teruyuki

    2010-01-26

    We describe molecular capturing properties of protein nanotubes with a controllable ligand binding affinity and size selectivity. These practical biocylinders were prepared using an alternating layer-by-layer (LbL) assembly of protein and oppositely charged poly(amino acid) into the nanoporous polycarbonate (PC) membrane (pore diameter, 400 nm), with subsequent dissolution of the template. The tube wall typically comprises six layers of poly-L-arginine (PLA) and human serum albumin (HSA) [(PLA/HSA)(3)]. Use of high molecular weight PLA (M(w) = ca. 70 000) yielded robust nanotubes, which are available as lyophilized powder. The (PLA/HSA)(3) nanotubes swelled considerably in water, although the outer diameter was almost unaltered. Uranyl ion, 3,3'-diethylthiacarbocyanine iodide, and zinc(II) protoporphyrin IX (ZnPP) were bound to the HSA component in the cylinder wall. Similar nanotubes comprising recombinant HSA mutant [rHSA(His)], which has a strong binding affinity for ZnPP, captured this ligand more tightly. Furthermore, addition of excess myristic acid released ZnPP from the tubes through a ligand replacement reaction. The hybrid nanotubes bearing a single avidin layer as an internal surface captured FITC-biotin efficiently. Biotin-labeled nanoparticles are also incorporated into the tubes when their particle size is sufficiently small to enter the pores. Subsequent TEM observation revealed a line of loaded nanoparticles (100 nm) in the one-dimensional space interior.

  3. Photocathodic Protection of 304 Stainless Steel by Bi2S3/TiO2 Nanotube Films Under Visible Light.

    Science.gov (United States)

    Li, Hong; Wang, Xiutong; Wei, Qinyi; Hou, Baorong

    2017-12-01

    We report the preparation of TiO2 nanotubes coupled with a narrow bandgap semiconductor, i.e., Bi2S3, to improve the photocathodic protection property of TiO2 for metals under visible light. Bi2S3/TiO2 nanotube films were successfully synthesized using the successive ionic layer adsorption and reaction (SILAR) method. The morphology and structure of the composite films were studied by scanning electron microscopy and X-ray diffraction, respectively. UV-visible diffuse reflectance spectra were recorded to analyze the optical absorption property of the composite films. In addition, the influence of Bi2S3 deposition cycles on the photoelectrochemical and photocathodic protection properties of the composite films was also studied. Results revealed that the heterostructure comprised crystalline anatase TiO2 and orthorhombic Bi2S3 and exhibited a high visible light response. The photocurrent density of Bi2S3/TiO2 was significantly higher than that of pure TiO2 under visible light. The sensitization of Bi2S3 enhanced the separation efficiency of the photogenerated charges and photocathodic protection properties of TiO2. The Bi2S3/TiO2 nanotubes prepared by SILAR deposition with 20 cycles exhibited the optimal photogenerated cathodic protection performance on the 304 stainless steel under visible light.

  4. Spin-polarized photoemission from SiGe heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Ferrari, A.; Bottegoni, F.; Isella, G.; Cecchi, S.; Chrastina, D.; Finazzi, M.; Ciccacci, F. [LNESS-Dipartimento di Fisica, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano (Italy)

    2013-12-04

    We apply the principles of Optical Orientation to measure by Mott polarimetry the spin polarization of electrons photoemitted from different group-IV heterostructures. The maximum measured spin polarization, obtained from a Ge/Si{sub 0.31}Ge{sub 0.69} strained film, undoubtedly exceeds the maximum value of 50% attainable in bulk structures. The explanation we give for this result lies in the enhanced band orbital mixing between light hole and split-off valence bands as a consequence of the compressive strain experienced by the thin Ge layer.

  5. Band Offsets Engineering for van der Waals Heterostructure Devices

    Science.gov (United States)

    Koda, Daniel S.; Bechstedt, Friedhelm; Marques, Marcelo; Teles, Lara K.

    Two-dimensional crystals (2D) and their stacks in van der Waals heterostructures became prospective for novel devices and physics. To surmount commensurability limitations within first-principles investigations, the coincidence lattice method is developed, enabling studies on interlayer twist and quasiparticle corrections despite limited computational resources. Interesting properties are observed within stacked systems, such as structural deformation on contact, strong orbital hybridization, and tunable band offsets by application of pressure and vertical electric fields. These studies could help to develop versatile electronic and optoelectronic devices and unravel new physics within 2D interfaces.

  6. Tunable Band Gaps of Mono-layer Hexagonal BNC Heterostructures

    OpenAIRE

    Peng, Qing; Zamiri, Amir; De, Suvranu

    2011-01-01

    Bandgap engineering by substituting C with B and N atoms in graphene has been shown to be a promising way to improve semiconducting properties of graphene. Such hybridized monolayers consisting of hexagonal BN phases in graphene (h-BNC) have been recently synthesized and char- acterized. In this paper, we present an ab initio density functional theory (DFT)-based study of h-BN domain size effect on band gap of mono-layer h-BNC heterostructures. The atomic structures, electronic band structure...

  7. Control of Interfacial Phenomena in Artificial Oxide Heterostructures

    Science.gov (United States)

    2015-09-01

    pathway to realizing new classes of devices that exhibit  functionalities not found in conventional technologies. New materials based on  perovskite ...approach to achieving high carrier densities is to use  interfaces involving  perovskite  oxide ABO3 heterostructures. So far, only SrTiO3 (STO) has been...conventional technologies. New materials based on perovskite oxides are promising because of their wide variety of properties, including electronic

  8. Carbon nanotubes: synthesis, structure, functionalization, and characterization.

    Science.gov (United States)

    Zamolo, Valeria Anna; Vazquez, Ester; Prato, Maurizio

    2014-01-01

    Carbon nanotubes have generated great expectations in the scientific arena, mainly due to their spectacular properties, which include a high aspect ratio, high strain resistance, and high strength, along with high conductivities. Nowadays, carbon nanotubes are produced by a variety of methods, each of them with advantages and disadvantages. Once produced, carbon nanotubes can be chemically modified, using a wide range of chemical reactions. Functionalization makes these long wires much easier to manipulate and dispersible in several solvents. In addition, the properties of carbon nanotubes can be combined with those of organic appendages. Finally, carbon nanotubes need to be carefully characterized, either as pristine or modified materials.

  9. Biomedical applications of carbon-nanotube composites.

    Science.gov (United States)

    Meredith, Jay Russell; Jin, Chunming; Narayan, Roger J; Aggarwal, Ravi

    2013-01-01

    The unique physical, chemical and mechanical properties of carbon nanotubes make them attractive for a variety of biomedical applications. Carbon nanotubes have been used to modify conventional biomedical materials to enhance mechanical properties, biocompatibility, or to impart other functionalities. New multifunctional composite materials using carbon nanotubes have been developed by combining them with inorganic, polymeric or biological materials. The biomedical applications for which novel carbon nanotube composites have been investigated include antimicrobial coatings, neural implants, tissue engineering scaffolds and electrochemical biosensors. In this paper, research on development and application of carbon nanotube composites for biomedical applications has been reviewed.

  10. Biocompatibility and drug release behavior of scaffolds prepared by coaxial electrospinning of poly(butylene succinate) and polyethylene glycol

    Energy Technology Data Exchange (ETDEWEB)

    Llorens, E.; Ibañez, H. [Departament d' Enginyeria Química, Universitat Politècnica de Catalunya, Av. Diagonal 647, Barcelona E-08028 (Spain); Valle, L.J. del, E-mail: luis.javier.del.valle@upc.edu [Departament d' Enginyeria Química, Universitat Politècnica de Catalunya, Av. Diagonal 647, Barcelona E-08028 (Spain); Puiggalí, J. [Departament d' Enginyeria Química, Universitat Politècnica de Catalunya, Av. Diagonal 647, Barcelona E-08028 (Spain); Center for Research in Nano-Engineering (CrNE), Universitat Politècnica de Catalunya, Edifici C, C/Pasqual i Vila s/n, Barcelona E-08028 (Spain)

    2015-04-01

    Scaffolds constituted by electrospun microfibers of poly(ethylene glycol) (PEG) and poly(butylene succinate) (PBS) were studied. Specifically, coaxial microfibers having different core–shell distributions and compositions were considered as well as uniaxial micro/nanofibers prepared from mixtures of both polymers. Processing conditions were optimized for all geometries and compositions and resulting morphologies (i.e. diameter and surface texture) characterized by scanning electron microscopy. Chemical composition, molecular interactions and thermal properties were evaluated by FTIR, NMR, XPS and differential scanning calorimetry. The PEG component of electrospun fibers could be solubilized by immersion of scaffolds in aqueous medium, giving rise to high porosity and hydrophobic samples. Nevertheless, a small amount of PEG was retained in the PBS matrix, suggesting some degree of mixing. Solubilization was slightly dependent on fiber structure; specifically, the distribution of PEG in the core or shell of coaxial fibers led to higher or lower retention levels, respectively. Scaffolds could be effectively loaded with hydrophobic drugs having antibacterial and anticarcinogenic activities like triclosan and curcumin, respectively. Their release was highly dependent on their chemical structure and medium composition. Thus, low and high release rates were observed in phosphate buffer saline (SS) and SS/ethanol (30:70 v/v), respectively. Slight differences in the release of triclosan were found depending on fiber distribution and composition. Antibacterial activity and biocompatibility were evaluated for both loaded and unloaded scaffolds. - Highlights: • Coaxial microfibers with different hydrophobicities were studied. • The surface morphology of the coaxial fiber shows the distribution of polymers. • Coaxial fiber microstructure favors the polymer molecular orientation. • These hybrid materials have greater advantages for loading and drug release. • PEG

  11. On the effect of addition of carbon nanotubes on the electric conductivity of alkali-activated slag mortars

    Science.gov (United States)

    Kusak, I.; Lunak, M.

    2017-09-01

    This paper presents basic electric properties of laboratory prepared alkali-activated composite materials on the basis of finely ground granular high furnace slag to which various quantities of carbon nanotubes (CNT) have been added. Impedance spectroscopy in the frequency range from 40 Hz to 1 MHz was used to measure the specimens. Electric resistivity ρ versus frequency and electric resistivity ρ versus CNT content relationships were examined on our specimens R&S ZNC vector analyser with DAK-12 coaxial probe (made by Speag) was used to carry out the measurements at higher frequencies (from 100 MHz to 3 GHz). Electric conductivity σ as a function of the frequency and as a function of the specimen CNT content was studied in this frequency range. Up-to-date instruments and a unique approach have evidently been employed to carry out non-destructive measurement of mortar materials.

  12. Fabrication of polyaniline/graphene/titania nanotube arrays nanocomposite and their application in supercapacitors

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Hua; Gan, Mengyu; Ma, Li, E-mail: mlsys607@126.com; Yu, Lei; Hu, Haifeng; Yang, Fangfang; Li, Yanjun; Ge, Chengqiang

    2015-05-05

    Highlights: • The PANI/graphene/TiO{sub 2} nanotube arrays were fabricated firstly. • The composite shows a high specific capacitance and superior rate capability. • A high capacity retention rate of 91% after 1000 cycles can be achieved. • The composite possesses a novel three-dimensional (3D) highly ordered nanostructure. • TiO{sub 2} NTs enhance the adhesion between PANI and substrate. - Abstract: Polyaniline/graphene/titania nanotube arrays (PGTNs) nanocomposite as a supercapacitor electrode is fabricated by in-situ polymerization for the first time. Herein, the PGTNs possesses a novel three-dimensional (3D) highly ordered hybrid nanostructure consisting of coaxial polyaniline (PANI)/TiO{sub 2} nanotube arrays and graphene coated with PANI on the surface of TiO{sub 2} in some degree. The synthesized three-dimensional PGTNs is characterized by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and Raman spectroscopy, and its electrochemical performance is measured by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and galvanostatic charge/discharge. The maximum specific capacitance of PGTNs is as high as 933 F g{sup −1} at current density of 0.75 A g{sup −1} and the specific capacitance retains 91% of the initial after constant charge–discharge 1000 cycles. The improved electrochemical performance is due to the 3D nanostructure, which effectively prevents the mechanical deformation during the fast charge/discharge process and favors the diffusion of the electrolyte ions into the inner region of active materials. The composite electrode material is very promising for the next generation of high-performance electrochemical supercapacitors.

  13. Quantum transport in carbon nanotubes

    DEFF Research Database (Denmark)

    Laird, Edward A.; Kuemmeth, Ferdinand; Steele, Gary A.

    2015-01-01

    modifies their transport behaviour. Interaction between electrons inside and outside a quantum dot is manifested in SU(4) Kondo behavior and level renormalization. Interaction within a dot leads to Wigner molecules and more complex correlated states. This review takes an experimental perspective informed...... and valley degrees of freedom. This review describes the modern understanding of transport through nanotube devices. Unlike conventional semiconductors, electrons in nanotubes have two angular momentum quantum numbers, arising from spin and from valley freedom. We focus on the interplay between the two....... In single quantum dots defined in short lengths of nanotube, the energy levels associated with each degree of freedom, and the spin-orbit coupling between them, are revealed by Coulomb blockade spectroscopy. In double quantum dots, the combination of quantum numbers modifies the selection rules of Pauli...

  14. Titania nanotube stabilized BiOCl nanoparticles in visible-light photocatalysis

    KAUST Repository

    Buchholcz, B.

    2017-03-14

    Photocatalysis is a green approach in environmental organic pollutant decomposition. Lately, considerable improvement in the activity of photocatalysts has been achieved with the realization of p–n heterostructures due to the lifetime extension of the photogenerated charge carriers. Herein, we report a facile synthesis approach for decorating n-type titanate nanotubes with p-type V–VI–VII compound semiconductor BiOCl nanoparticles. It is well-known that BiOX (X = Cl, Br, I) materials form nanometer-thick platelets, which can eventually assemble into micrometer size flower-like 3D structures. Here, we demonstrate that the tubular titanate support can stabilize BiOCl on its surface in the form of nanoparticles measuring a few nanometers in diameter, instead of forming the well-known bismuth-oxyhalide nanoflowers. Subsequent calcination at 400 °C transforms the pristine titanate structures into one-dimensional anatase nanotubes, along with the formation of a heterojunction at the interface of the emerging Bi2Ti2O7 and anatase phases. The resulting nanocomposite shows activity in visible-light photocatalytic test reactions.

  15. Assembly of three-dimensional hetero-epitaxial ZnO/ZnS core/shell nanorod and single crystalline hollow ZnS nanotube arrays.

    Science.gov (United States)

    Huang, Xing; Wang, Meng; Willinger, Marc-Georg; Shao, Lidong; Su, Dang Sheng; Meng, Xiang-Min

    2012-08-28

    Hetero-epitaxial growth along three-dimensional (3D) interfaces from materials with an intrinsic large lattice mismatch is a key challenge today. In this work we report, for the first time, the controlled synthesis of vertically aligned ZnO/ZnS core/shell nanorod arrays composed of single crystalline wurtzite (WZ) ZnS conformally grown on ZnO rods along 3D interfaces through a simple two-step thermal evaporation method. Structural characterization reveals a "(01-10)(ZnO)//(01-10)(ZnS) and [0001](ZnO)//[0001](ZnS)" epitaxial relationship between the ZnO core and the ZnS shell. It is exciting that arrays of single crystalline hollow ZnS nanotubes are also innovatively obtained by simply etching away the inner ZnO cores. On the basis of systematic structural analysis, a rational growth mechanism for the formation of hetero-epitaxial core/shell nanorods is proposed. Optical properties are also investigated via cathodoluminescence and photoluminescence measurements. Remarkably, the synthesized ZnO/ZnS core/shell heterostructures exhibit a greatly reduced ultraviolet emission and dramatically enhanced green emission compared to the pure ZnO nanorods. The present single-crystalline heterostructure and hollow nanotube arrays are envisaged to be highly promising for applications in novel nanoscale optoelectronic devices, such as UV-A photodetectors, lasers, solar cells, and nanogenerators.

  16. Coaxial Electrospray of Ranibizumab-Loaded Microparticles for Sustained Release of Anti-VEGF Therapies.

    Directory of Open Access Journals (Sweden)

    Leilei Zhang

    Full Text Available Age-related macular degeneration (AMD is the leading cause of vision loss and blindness in people over age 65 in industrialized nations. Intravitreous injection of anti-VEGF (vascular endothelial growth factor therapies, such as ranibizumab (trade name: Lucentis, provides an effective treatment option for neovascular AMD. We have developed an improved coaxial electrospray (CES process to encapsulate ranibizumab in poly(lactic-co-glycolic acid (PLGA microparticles (MPs for intravitreous injection and sustained drug release. This microencapsulation process is advantageous for maintaining the stability of the coaxial cone-jet configurations and producing drug-loaded MPs with as high as 70% encapsulation rate and minimal loss of bioactivitiy. The utility of this emerging process in intravitreous drug delivery has been demonstrated in both benchtop and in vivo experiments. The benchtop test simulates ocular drug release using PLGA MPs encapsulating a model drug. The in vivo experiment evaluates the inflammation and retinal cell death after intravitreal injection of the MPs in a chick model. The experimental results show that the drug-load MPs are able to facilitate sustained drug release for longer than one month. No significant long term microglia reaction or cell death is observed after intravitreal injection of 200 μg MPs. The present study demonstrates the technical feasibility of using the improved CES process to encapsulate water-soluble drugs at a high concentration for sustained release of anti-VEGF therapy.

  17. Design and application of coaxial wigglers in free-electron lasers

    Science.gov (United States)

    Jackson, Robert H.; Blank, Monica; Freund, Henry P.; Pershing, Dean E.; Taccetti, J. M.

    1995-09-01

    The Naval Research Laboratory is investigating innovative magnetic wigglers to reduce beam energy requirements for millimeter wave FELs and to enhance the gain and efficiency. Recent work has focused on coaxial designs. The advantages of this are twofold. First, annular configurations are advantageous for propagating high current beams. The annular geometry permits use of the central structure to enhance the wiggler field, hence, allowing shorter wiggler periods. One such wiggler is referred to as the Coaxial Hybrid Iron (CHI) wiggler, and employs a solenoid enclosing periodic arrays of ferromagnetic and nonferromagnetic material arranged as an outer ring and an inner rod. A second wiggler uses both outer and inner bifilar helical current windings. Both wiggler designs result in substantial enhancements in the wiggler field experienced by the electron beam as compared with the fields in the absence of the central structure. A prototype CHI wiggler is discussed along with a 35 GHz amplifier experiment which is under construction. Preliminary performance calculations for a two helix wiggler system are discussed. This will include both orbit theory and a fully 3D nonlinear simulation of the interaction.

  18. Effects of impedance mismatch and coaxial cable length on absolute gravimeters

    Science.gov (United States)

    Křen, Petr; Pálinkáš, Vojtech; Mašika, Pavel; Vaľko, Miloš

    2017-04-01

    The systematic effects of absolute gravimeters have to be investigated to fully utilize their capabilities in metrology and geosciences. In Křen et al (2016 Metrologia 53 27-40) we found that for an FG5 gravimeter, even a few meter long coaxial cable used for transmission of fringe signal causes systematic features in residuals and errors at the level of 1-2 µGal. In this paper, we present experimental results and appropriate models to explain the effects that were found to be caused by impedance mismatches of electronic components and dispersion effects in coaxial cables of gravimeters. The experimental results have been obtained for analogue and transistor-transistor logic (TTL) compatible signals in the FG5-215 gravimeter and for a TTL signal in the FG5X-251 gravimeter. We found that dispersion and impedance mismatch effects are similar for both gravimeters. Furthermore, we describe a model of the dispersion that allows an evaluation of the effect/correction for a given range of the free-fall and thus it is also applicable to other gravimeters. The effect of impedance mismatch for the analogue fringe signal is modelled as an effect of the reflected electronic signal on the evaluation of zero-crossings. The applicability of this model for TTL signal is also discussed.

  19. Fabrication and impact performance of three-dimensionally integrated microstrip antennas with microstrip and coaxial feeding

    Science.gov (United States)

    Yao, Lan; Wang, Xin; Xu, Fujun; Zhao, Da; Jiang, Muwen; Qiu, Yiping

    2009-09-01

    A conformal load-bearing antenna structure (CLAS) combines the antenna into a composite structure such that it can carry the designed load while functioning as an antenna. In this paper, two types of new 3D integrated microstrip antennas (3DIMAs) with different feeding methods are designed to work at the radar L-band. Different from the conventional CLAS, the radiating patch and the ground plane of the 3DIMA are both composed of woven conductive wires and are bonded into the 3D composite physically by Z-yarns, greatly improving the damage tolerance of the antenna. The return loss of the coaxial-fed antenna is -13.15 dB with a resonant frequency of 1.872 GHz, while that of the microstrip-fed antenna is -31.50 dB with a resonant frequency of 1.33 GHz. Both of the 3DIMAs have similar radiation patterns to that of the traditionally designed microstrip antenna. In addition, an experimental investigation of the impact response of the coaxial-fed 3DIMA was carried out and the results showed the radiation pattern had almost no change even when the antenna received an impact energy of 15 J, exhibiting superior impact resistance to that of a conventional microstrip antenna.

  20. Measuring concentricity and coaxial tolerance of nozzle and cavity with tool microscope

    Science.gov (United States)

    Lu, Xizhao; Jiang, Feng; Ye, Ruifang; Lei, Tingping

    2016-01-01

    While the equipment of Micro-jet wave-guided laser was assembled, high-precision of concentricity and coaxiality between nozzle and cavity are required, which directly or indirectly influent the laser coupling precision of nozzle, the micro-jet stability and the steady length of micro-jet as well. As a result, the measurement of concentricity and coaxiality is important to improve the processing quality of Micro-jet wave-guided laser Through the new digital universal tool microscope measuring both ends of micro nozzle and diameter of nozzle, more resolution the other hand, the backlight detection the edge of nozzle is utilized. When the position of the center of a circle is indirect measured and then find out the concentricity through the uncertainty of the measurement and calculation method. V shaped groove is utilized to make certain its position. Otherwise, digital imaging through setting fixture and the use of new digital universal tool microscope and processed by software, which will cause to reduce measurement human error in tradition, after that, error theory analysis will be carried out, uncertainty theory will be utilized to make the experiment more sure at the same time. Above all, the reliability of data is obtained, compared with the traditional measurement methods are more accurate. Therefore, the processing quality of laser drilling will be enhanced significantly.

  1. Modelling and robust control of an unmanned coaxial rotor helicopter with unstructured uncertainties

    Directory of Open Access Journals (Sweden)

    Zhi-Yan Dong

    2017-01-01

    Full Text Available A complete methodology for an unmanned coaxial rotor helicopter with unstructured uncertainties was proposed to achieve high-accuracy tracking performance from modelling to robust control. An integrative approach was introduced to systematically construct a whole dynamic model. The key parameters were selected carefully after iteratively being checked by empirical coefficients to decrease the budget and risk of programme. Moreover, a new control scheme is proposed to simultaneously incorporate six inputs to control six states based on the investment of singularity value responses and the general rule of relative gain array. Coprime factor uncertainty model is considered to represent a class of unstructured uncertainties, such as unmolded actuator dynamics and unpredicted interferences between two rotors. Furthermore, the H ∞ loop-shaping control was proposed to apply the control design of the coaxial rotor helicopter to manage complicated uncertainties and multivariable coupling. Finally, simulation results show the effectiveness of the proposed controller design in the step response of the closed loop. The stable closed-loop plant is achieved and the tolerant size of unstructured uncertainty is up to 36.09%. Good step responses and satisfied decoupling were also investigated in detail.

  2. Rebreathing, resistance and external work of breathing in three different coaxial Mapleson D systems.

    Science.gov (United States)

    Jonsson, L O; Zetterström, H

    1989-01-01

    Using a lung model, rebreathing characteristics, resistance against gas flow and the external work of breathing were tested in three different coaxial Mapleson D systems: the Medicvent D system, the Bain original system and the Coax-II system. The rebreathing characteristics were found to be similar in all systems in both spontaneous and controlled ventilation. The Bain system was found to have the lowest resistance and work of breathing and the Coax-II system the highest. The differences were small and clinically insignificant. Both the resistance and the work of breathing increased with fresh gas flow. The resistance against expiration was found to be in the range 135-160 Pa at a total gas flow of 31 1.min-1, which is well within the acceptable level. The resulting end-expiratory pressure was never above 100 Pa (1 cmH2O) in any system. We concluded that there was no clinically significant difference among the three systems despite differences in design. The coaxial Mapleson D systems can also be used safely with high fresh gas flows with regard to resistance and end-expiratory pressures.

  3. Core-shell structured PEO-chitosan nanofibers by coaxial electrospinning.

    Science.gov (United States)

    Pakravan, Mehdi; Heuzey, Marie-Claude; Ajji, Abdellah

    2012-02-13

    Core-shell structured PEO-chitosan nanofibers have been produced using a coaxial electrospinning setup. PEO and chitosan solutions, both in an aqueous acetic acid solvent, were used as the inner (core) and outer (shell) layer, respectively. Uniform-sized defect-free nanofibers of 150-190 nm diameter were produced. In addition, hollow nanofibers could be obtained subsequent to PEO washing of the membranes. The core-shell nanostructure and existence of chitosan on the shell layer were confirmed by TEM images obtained before and after washing the PEO content with water. The presence of chitosan on the surface of the composite nanofibers was further supported by XPS studies. The chitosan and PEO compositions in the nanofibrous mats were determined by TGA analysis, which were similar to their ratio in the feed solutions. The local compositional homogeneity of the membranes and the efficiency of the washing step to remove PEO were also verified by FTIR. In addition, DSC and XRD were used to characterize the crystalline structure and morphology of the co-electrospun nonwoven mats. The prepared coaxial nanofibers (hollow and solid) have several potential applications due to the presence of chitosan on their outer surfaces.

  4. Coaxial fiber-optic chemical-sensing excitation-emission matrix fluorometer.

    Science.gov (United States)

    Kim, Yoon-Chang; Jordan, James A; Chávez, Diana; Booksh, Karl S

    2011-02-01

    Great reductions in the overall size and complexity of high throughput multichannel UV-visible fluorometers were achieved by coupling a compact optical fiber array to compact dispersive transmission optics. The coaxial configuration centers on the insertion of a silica/silica optical fiber into the hollow region of a UV-fused silica capillary waveguide. The outer core delivers the maximum power of the narrow wavelength region of the excitation spectrum created by coupling a xenon arc discharge lamp to a compact spectrometer. The molecular fluorescence resulting from the interaction of light emitted at the distal end of the hollow waveguide and the sample matrix is received and transmitted to a CCD via a compact dispersive grating-prism (grism) optical assembly. A linear array of the coaxial optical fibers permits a full excitation-emission matrix spectrum of the analyte matrix to be projected onto the face of the CCD. The in situ identification and monitoring of polycyclic aromatic hydrocarbons was carried out for the initial application testing for this prototype.

  5. Starch/PCL composite nanofibers by co-axial electrospinning technique for biomedical applications.

    Science.gov (United States)

    Komur, B; Bayrak, F; Ekren, N; Eroglu, M S; Oktar, F N; Sinirlioglu, Z A; Yucel, S; Guler, O; Gunduz, O

    2017-03-29

    In this study, starch and polycaprolactone (PCL), composite nanofibers were fabricated by co-axial needle electrospinning technique. Processing parameters such as polymer concentration, flow rate and voltage had a marked influence on the composite fiber diameter. Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), mechanical and physical properties (such as density, viscosity and electrical conductivity) of the composite fibres were evaluated. Moreover, a cell culture test was performed in order to determine their cytotoxicity for wound dressing application. The effect of starch ratio in the solution on the properties and morphological structure of the fibers produced was presented. With lower starch concentration values, the fibers have greater ultimate tensile strength characteristic (mostly 4 and 5 wt%). According to SEM results, it can be figured out that the nanofibers fabricated have good spinnability and morphology. The mean diameter of the fibers is about 150 nm. According to results of cell culture study, the finding can be determined that the increase of starch in the fiber also increases the cell viability. Composite nanofibers of starch/PCL have been prepared using a co-axial needle electrospinning technique. PCL was successfully encapsulated within starch. Fiber formation was observed for different ratio of starch. With several test, analysis and measurement performed, some important parameters such as quality and effectuality of each fiber obtained for wound dressing applications were discussed in detail.

  6. Grating-flanked plasmonic coaxial apertures for efficient fiber optical tweezers.

    Science.gov (United States)

    Saleh, Amr A E; Sheikhoelislami, Sassan; Gastelum, Steven; Dionne, Jennifer A

    2016-09-05

    Subwavelength plasmonic apertures have been foundational for direct optical manipulation of nanoscale specimens including sub-100 nm polymeric beads, metallic nanoparticles and proteins. While most plasmonic traps result in two-dimensional localization, three-dimensional manipulation has been demonstrated by integrating a plasmonic aperture on an optical fiber tip. However, such 3D traps are usually inefficient since the optical mode of the fiber and the subwavelength aperture only weakly couple. In this paper we design more efficient optical-fiber-based plasmonic tweezers combining a coaxial plasmonic aperture with a plasmonic grating coupler at the fiber tip facet. Using full-field finite difference time domain analysis, we optimize the grating design for both gold and silver fiber-based coaxial tweezers such that the optical transmission through the apertures is maximized. With the optimized grating, we show that the maximum transmission efficiency increases from 2.5% to 19.6% and from 1.48% to 16.7% for the gold and silver structures respectively. To evaluate their performance as optical tweezers, we calculate the optical forces and the corresponding trapping potential on dielectric particles interacting with the apertures. We demonstrate that the enahncement in the transmission translates into an equivalent increase in the optical forces. Consequently, the optical power required to achieve stable optical trapping is significantly reduced allowing for efficient localization and 3D manipulation of sub-30 nm dielectric particles.

  7. Tuning the Carrier Confinement in GeS/Phosphorene van der Waals Heterostructures.

    Science.gov (United States)

    Wang, Chan; Peng, Lei; Qian, Qi; Du, Jinyan; Wang, Sufan; Huang, Yucheng

    2018-01-11

    Van der Waals (vdW) heterostructures, which have the advantage of integrating excellent properties of the stacked 2D materials by vdW interactions, have gained increasing attention recently. In this work, within the framework of density functional theory calculations, the electronic properties of vdW heterostructure composed of phosphorene (BP) in black phosphorus phase and GeS monolayer are systematically explored. The results show that the carriers are not separated for both lattice-match and lattice-mismatch heterostructures. For the lattice-match heterostructure, it is found that changing monolayer of GeS to bilayer can increase the energy difference of valence band offsets between GeS and BP, thus realizing electron-hole separation. For the lattice-mismatch heterostructure, altering the layer distance can transform the heterostructure into a typical type-I alignment, but applying the electric field or doping with 2, 3, 5, 6-tetrafluoro-7, 7, 8, 8-tetracyanoquinodimethane (F4TCNQ) can make it display a perfect desirable type-II alignment, where holes migration and electrons transfer are revealed to account respectively for the phenomenon of carrier separation. It is believed that the work would greatly enlarge the potential application of the BP-based heterostructures in photoelectronics and further stimulate the investigation enthusiasms on other fashionable heterostructures and even unassuming heterostructures in which the charming electronic properties can be modulated to emerge by various general methods. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Universally dispersible carbon nanotubes.

    Science.gov (United States)

    Prevoteau, Alexandre; Soulié-Ziakovic, Corinne; Leibler, Ludwik

    2012-12-12

    We show that supramolecular chemistry provides a convenient tool to prepare carbone nanotubes (CNTs) that can be dispersed in solvents of any chemical nature, easily recovered and redispersed. Thymine-modified CNTs (CNT-Thy) can be dispersed in solution in the presence of diaminotriazine (DAT) end-functionalized polymers, through supramolecular Thy/DAT association. DAT-polymer chains are selected according to the solvent chemical nature: polystyrene (PS) for hydrophobic/low polarity solvents and a propylene oxide/ethylene oxide copolymer (predominantly propylene oxide based, PPO/PEO) for polar solvents or water. Long-term stable supramolecular CNT dispersions are reversibly aggregated by adding a few droplets of a selective dissociating agent of the Thy/DAT association (DMSO). CNT-Thy, simply recycled by centrifugation or filtration, can be redispersed in another solvent in presence of a suitable soluble DAT-polymer. Dispersion and aggregation can also be switched on and off by choosing a polymer for which a given solvent is close to Θ-conditions, e.g., PS in cyclohexane or PPO/PEO in water.

  9. Carbon nanotube computer.

    Science.gov (United States)

    Shulaker, Max M; Hills, Gage; Patil, Nishant; Wei, Hai; Chen, Hong-Yu; Wong, H-S Philip; Mitra, Subhasish

    2013-09-26

    The miniaturization of electronic devices has been the principal driving force behind the semiconductor industry, and has brought about major improvements in computational power and energy efficiency. Although advances with silicon-based electronics continue to be made, alternative technologies are being explored. Digital circuits based on transistors fabricated from carbon nanotubes (CNTs) have the potential to outperform silicon by improving the energy-delay product, a metric of energy efficiency, by more than an order of magnitude. Hence, CNTs are an exciting complement to existing semiconductor technologies. Owing to substantial fundamental imperfections inherent in CNTs, however, only very basic circuit blocks have been demonstrated. Here we show how these imperfections can be overcome, and demonstrate the first computer built entirely using CNT-based transistors. The CNT computer runs an operating system that is capable of multitasking: as a demonstration, we perform counting and integer-sorting simultaneously. In addition, we implement 20 different instructions from the commercial MIPS instruction set to demonstrate the generality of our CNT computer. This experimental demonstration is the most complex carbon-based electronic system yet realized. It is a considerable advance because CNTs are prominent among a variety of emerging technologies that are being considered for the next generation of highly energy-efficient electronic systems.

  10. Rotor hover performance and system design of an efficient coaxial rotary wing micro air vehicle

    Science.gov (United States)

    Bohorquez, Felipe

    2007-12-01

    Rotary-wing Micro air vehicles (MAVs) due to their unique hovering and low-speed flight capabilities are specially suited for missions that require operation in constrained spaces. Size restrictions force MAVs to operate in a low Reynolds number aerodynamic regime where viscous effects are dominant. This results in poor aerodynamic performance of conventional airfoils and rotor configurations. This dissertation explores the design issues that affect the hover performance of small-scale rotors and the implementation of a working coaxial MAV prototype. A computerized hover test stand was used for the systematic testing of single and coaxial small-scale rotors. Thin circular arcs were chosen for blade manufacturing because of their good aerodynamic characteristics at low Reynolds numbers, and simplified parameterization. Influence of airfoil geometry on single rotor hover performance was studied on untwisted rectangular blades. Non rectangular blades were used to study coupled airfoil and blade parameters. Tip tapered geometries were manufactured by removing material from baseline rectangular blades producing a coupling between blade planform, twist distribution, and spanwise airfoil shape. Performance gains were obtained by introducing large negative twist angles over short radial distances at the blade tips. A parametric study of the blade geometries resulted in maximum figures of merit of 0.65. Coaxial rotor performance at torque equilibrium was explored for different trims and operating conditions. It was found that the upper rotor was marginally affected by the lower one at spacings larger than 35% of the rotor radius, and that it produced about 60% of the total thrust. Experiments showed that power loading was maximized when higher collectives were used at the lower rotor, resulting in sizable differences in rotational speed between rotors. The CFD solver INS2d was used for a two-dimensional parametric aerodynamic study of circular arc airfoils. Lift, drag, and

  11. Semiconductor-oxide heterostructured nanowires using postgrowth oxidation.

    Science.gov (United States)

    Wallentin, Jesper; Ek, Martin; Vainorious, Neimantas; Mergenthaler, Kilian; Samuelson, Lars; Pistol, Mats-Erik; Reine Wallenberg, L; Borgström, Magnus T

    2013-01-01

    Semiconductor-oxide heterointerfaces have several electron volts high-charge carrier potential barriers, which may enable devices utilizing quantum confinement at room temperature. While a single heterointerface is easily formed by oxide deposition on a crystalline semiconductor, as in MOS transistors, the amorphous structure of most oxides inhibits epitaxy of a second semiconductor layer. Here, we overcome this limitation by separating epitaxy from oxidation, using postgrowth oxidation of AlP segments to create axial and core-shell semiconductor-oxide heterostructured nanowires. Complete epitaxial AlP-InP nanowire structures were first grown in an oxygen-free environment. Subsequent exposure to air converted the AlP segments into amorphous aluminum oxide segments, leaving isolated InP segments in an oxide matrix. InP quantum dots formed on the nanowire sidewalls exhibit room temperature photoluminescence with small line widths (down to 15 meV) and high intensity. This optical performance, together with the control of heterostructure segment length, diameter, and position, opens up for optoelectrical applications at room temperature.

  12. Epitaxial Heterostructures of Lead Selenide Quantum Dots on Hematite Nanowires.

    Science.gov (United States)

    Selinsky, Rachel S; Shin, Sanghun; Lukowski, Mark A; Jin, Song

    2012-06-21

    We present a novel method for synthesizing epitaxial quantum dot-nanowire (QD-NW) heterostructures using the example of colloidal PbSe QDs decorated on furnace-grown hematite (α-Fe2O3) NWs. The direct heterogeneous nucleation of QDs on Fe2O3 NWs relies upon an aggressive surface dehydration of the as-synthesized Fe2O3 NWs at 350 °C under vacuum and subsequent introduction of colloidal reactants resulting in direct growth of PbSe QDs on Fe2O3. The synthesis is tunable: the QD diameter distribution and density of QDs on the NWs increase with increased dehydration time, and QD diameters and size distributions decrease with decreased injection temperature of the colloidal synthesis. Transmission electron microscopy (TEM) structural analysis reveals direct heteroepitaxial heterojunctions where the matching faces can be PbSe (002) and Fe2O3 (003) with their respective [11̅0] crystallographic directions aligned. This can be a general approach for integrating colloidal and furnace synthetic techniques, thus broadening possible material combinations for future high-quality, epitaxial nanoscale heterostructures for solar applications.

  13. The direct magnetoelectric effect in ferroelectric-ferromagnetic epitaxial heterostructures.

    Science.gov (United States)

    Fina, I; Dix, N; Rebled, J M; Gemeiner, P; Martí, X; Peiró, F; Dkhil, B; Sánchez, F; Fàbrega, L; Fontcuberta, J

    2013-09-07

    Ferroelectric (FE) and ferromagnetic (FM) materials engineered in horizontal heterostructures allow interface-mediated magnetoelectric coupling. The so-called converse magnetoelectric effect (CME) has been already demonstrated by electric-field poling of the ferroelectric layers and subsequent modification of the magnetic state of adjacent ferromagnetic layers by strain effects and/or free-carrier density tuning. Here we focus on the direct magnetoelectric effect (DME) where the dielectric state of a ferroelectric thin film is modified by a magnetic field. Ferroelectric BaTiO3 (BTO) and ferromagnetic CoFe2O4 (CFO) oxide thin films have been used to create epitaxial FE/FM and FM/FE heterostructures on SrTiO3(001) substrates buffered with metallic SrRuO3. It will be shown that large ferroelectric polarization and DME can be obtained by appropriate selection of the stacking order of the FE and FM films and their relative thicknesses. The dielectric permittivity, at the structural transitions of BTO, is strongly modified (up to 36%) when measurements are performed under a magnetic field. Due to the insulating nature of the ferromagnetic layer and the concomitant absence of the electric-field effect, the observed DME effect solely results from the magnetostrictive response of CFO elastically coupled to the BTO layer. These findings show that appropriate architecture and materials selection allow overcoming substrate-induced clamping in multiferroic multi-layered films.

  14. Strain profile in nitride based multilayer nano-heterostructures

    Science.gov (United States)

    Gupta, Sapna; Rahman, F.; Siddiqui, M. J.; Alvi, P. A.

    2013-02-01

    This article has focused on the behavior of strain produced in the III-nitride based multilayer nano-heterostructure such as GaN/AlGaN, InN/AlInN, and InN/GaInN. Moreover, the variations in the strain with different material compositions for the proposed structures have also been reported. In this paper, the eight band k.p method has been utilized to compute the strain produced due to lattice mismatch between the binary and ternary semiconducting thin epitaxial layers in the multilayer nano-heterostructure. The strain has been simulated for entire model of size 288 nm, but the significant strain has been observed only in the quantum region that lies between 100 nm and 188 nm. For all models under simulation, the strain in the quantum region is found to be tensile along both x and y directions, while compressive in nature along z-direction. The correlation between strain and bandgap for the structures has also been reported. The Results presented in the paper may be beneficial for entire nano-optoelectronics community.

  15. THz investigations of graphene-complex-oxide heterostructures

    Science.gov (United States)

    Jnawali, Giriraj; Chen, Lu; Irvin, Patrick; Levy, Jeremy; Ryu, Sangwoo; Eom, Chang-Beom; Ghahari, Fereshte; Ravichandran, Jayakanth; Kim, Philip

    2014-03-01

    The unique and multifaceted properties of graphene have fascinated scientists and engineers for a decade now. A new frontier in research concerns properties of graphene in the THz-IR region, where the collective excitation of graphene 2D electron gas (2DEG) into plasmonic waves has proven the salient feature.[2] Complex oxide heterostructures (e.g., LaAlO3/SrTiO3, LAO/STO) also support a 2DEG with high carrier densities and expected plasmonic behavior. A unique feature of the LAO/STO system is the ability to control the electron density with nanoscale precision.[3] In addition, a method for sourcing and detecting broadband THz emission from LAO/STO nanojunctions has been recently demonstrated.[4] Here we describe initial efforts to investigate the THz properties of graphene-complex oxide (GCO) heterostructures. We envision that the proposed graphene plasmonic devices in the GCO will help to lay the foundation for a host of powerful THz-IR technologies for signal processing, imaging, spectroscopy and chemical sensing. We gratefully acknowledge support for this work from ONR (N00014-13-1-0806) and AFOSR (FA9550-12-1-0268).

  16. Fabrication and transport studies of graphene-superconductor heterostructures

    Science.gov (United States)

    Hu, Jiuning; Wu, Tailung; Tian, Jifa; Chen, Yong

    2014-03-01

    Recently, graphene based stacked heterostructures, e.g., graphene and boron nitride (BN) multi-layers, have attracted much attention as a system to study novel interaction-driven physics (e.g., excitonic condensation) and perform interesting measurements (eg. Coulomb drag and tunneling). The realm of graphene-superconductor heterostructures remains less unexplored, while such a system offers various interesting prospects (effects of superconductor vortices lattices on over-layering graphene and quantum Hall states, where novel phenomena such as anionic excitations have been predicted). We have used polyvinyl alcohol (PVA) based carrier films and a micro-manipulator to transfer mechanically exfoliated flakes and fabricated graphene/BN/NbSe2 structures to study the transport properties of graphene in close proximity to electrically isolated superconducting NbSe2 films. The NbSe2 film shows the superconducting transition temperature of ~7 K and upper critical field of ~3.5 T after device fabrication. We will present results from magneto-transport in graphene and graphene-NbSe2 Coulomb drag and tunneling measurements.

  17. Band offsets in ITO/Ga2O3 heterostructures

    Science.gov (United States)

    Carey, Patrick H.; Ren, F.; Hays, David C.; Gila, B. P.; Pearton, S. J.; Jang, Soohwan; Kuramata, Akito

    2017-11-01

    The valence band offsets in rf-sputtered Indium Tin Oxide (ITO)/single crystal β-Ga2O3 (ITO/Ga2O3) heterostructures were measured with X-Ray Photoelectron Spectroscopy using the Kraut method. The bandgaps of the component materials in the heterostructure were determined by Reflection Electron Energy Loss Spectroscopy as 4.6 eV for Ga2O3 and 3.5 eV for ITO. The valence band offset was determined to be -0.78 ± 0.30 eV, while the conduction band offset was determined to be -0.32 ± 0.13 eV. The ITO/Ga2O3 system has a nested gap (type I) alignment. The use of a thin layer of ITO between a metal and the Ga2O3 is an attractive approach for reducing contact resistance on Ga2O3-based power electronic devices and solar-blind photodetectors.

  18. Resonant Photonic States in Coupled Heterostructure Photonic Crystal Waveguides

    Directory of Open Access Journals (Sweden)

    Sabarinathan J

    2010-01-01

    Full Text Available Abstract In this paper, we study the photonic resonance states and transmission spectra of coupled waveguides made from heterostructure photonic crystals. We consider photonic crystal waveguides made from three photonic crystals A, B and C, where the waveguide heterostructure is denoted as B/A/C/A/B. Due to the band structure engineering, light is confined within crystal A, which thus act as waveguides. Here, photonic crystal C is taken as a nonlinear photonic crystal, which has a band gap that may be modified by applying a pump laser. We have found that the number of bound states within the waveguides depends on the width and well depth of photonic crystal A. It has also been found that when both waveguides are far away from each other, the energies of bound photons in each of the waveguides are degenerate. However, when they are brought close to each other, the degeneracy of the bound states is removed due to the coupling between them, which causes these states to split into pairs. We have also investigated the effect of the pump field on photonic crystal C. We have shown that by applying a pump field, the system may be switched between a double waveguide to a single waveguide, which effectively turns on or off the coupling between degenerate states. This reveals interesting results that can be applied to develop new types of nanophotonic devices such as nano-switches and nano-transistors.

  19. Excellent valleytronic properties and nontrivial topological phase in germanene heterostructure

    Science.gov (United States)

    Qu, Jinfeng; Peng, Xiangyang; Luo, Chaobo; Zhong, Jianxin

    2017-10-01

    In comparison with transition metal dichalcogenides (TMDs), germanene is not an ideal valleytronic material due to its very weak spin–orbit coupling (SOC) and tiny band gap. By performing density functional calculations, we studied the heterostructures of germanene/Sb and germanene/SbF in order to augment the valleytronic properties of germanene to a level similar to that of TMDs. Although germanene/Sb has large spin splittings, the system is found to be gapless. By proximity with the fluorine-adsorbed Sb layer, germanene can acquire large SOC. Germanene/SbF has a sizable direct band gap at Dirac points and the Dirac valleys of SbF and germanene are preserved in the heterostructure. The Ge–SbF interaction breaks the inversion symmetry, leading to large spin splittings and Berry curvatures, which are valley contrasting due to time reversal symmetry. We studied the interband optical transitions and found that valley polarization is achievable via valley-selective circular dichroism. The calculated Z 2 topological invariant further confirms that Ge/SbF is a topological insulator. Our studies illustrate that weak SOC materials can be converted into good valleytronic material and that nontrivial topological phase and valleytronic properties can be simultaneously realized.

  20. Graphene/CdTe heterostructure solar cell and its enhancement with photo-induced doping

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Shisheng, E-mail: shishenglin@zju.edu.cn; Chen, Hongsheng [Department of Information Science and Electronic Engineering, Zhejiang University, Hangzhou 310027 (China); State Key Laboratory of Modern Optical Instrumentation, Zhejiang University, Hangzhou 310027 (China); Li, Xiaoqiang; Zhang, Shengjiao; Wang, Peng; Xu, Zhijuan; Zhong, Huikai; Wu, Zhiqian [Department of Information Science and Electronic Engineering, Zhejiang University, Hangzhou 310027 (China)

    2015-11-09

    We report a type of solar cell based on graphene/CdTe Schottky heterostructure, which can be improved by surface engineering as graphene is atomic thin. By coating a layer of ultrathin CdSe quantum dots onto graphene/CdTe heterostructure, the power conversion efficiency is increased from 2.08% to 3.10%. Photo-induced doping is mainly accounted for this enhancement, as evidenced by field effect transport, Raman, photoluminescence, and quantum efficiency measurements. This work demonstrates a feasible way of improving the performance of graphene/semiconductor heterostructure solar cells by combining one dimensional with two dimensional materials.