29 CFR 1910.1002 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 6 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1910.1002... Hazardous Substances § 1910.1002 Coal tar pitch volatiles; interpretation of term. As used in § 1910.1000 (Table Z-1), coal tar pitch volatiles include the fused polycyclic hydrocarbons which volatilize from the...

Potential contributions of asphalt and coal tar to black carbon quantification in urban dust, soils, and sediments

Energy Technology Data Exchange (ETDEWEB)

Yang, Y.; Mahler, B.J.; Van Metre, P.C.; Ligouis, B.; Werth, C.J. [University of Illinois Urbana Champaign, Urbana, IL (USA). Dept. of Civil & Environmental Engineering

2010-12-01

Measurements of black carbon (BC) using either chemical or thermal oxidation methods are generally thought to indicate the amount of char and/or soot present in a sample. In urban environments, however, asphalt and coal-tar particles worn from pavement are ubiquitous and, because of their pyrogenic origin, could contribute to measurements of BC. Here we explored the effect of the presence of asphalt and coal-tar particles on the quantification of BC in a range of urban environmental sample types, and evaluated biases in the different methods used for quantifying BC. Samples evaluated were pavement dust, residential and commercial area soils, lake sediments from a small urban watershed, and reference materials of asphalt and coal tar. Total BC was quantified using chemical treatment through acid dichromate (Cr{sub 2}O{sub 7}) oxidation and chemo-thermal oxidation at 375{sup o}C (CTO-375). BC species, including soot and char/charcoal, asphalt, and coal tar, were quantified with organic petrographic analysis. Comparison of results by the two oxidation methods and organic petrography indicates that both coal tar and asphalt contribute to BC quantified by Cr{sub 2}O{sub 7} oxidation, and that coal tar contributes to BC quantified by CTO-375. These results are supported by treatment of asphalt and coal-tar reference samples with Cr2O7 oxidation and CTO-375. The reference asphalt is resistant to Cr{sub 2}O{sub 7} oxidation but not to CTO-375, and the reference coal tar is resistant to both Cr2O7 oxidation and CTO-375. These results indicate that coal tar and/or asphalt can contribute to BC measurements in samples from urban areas using Cr{sub 2}O{sub 7} oxidation or CTO-375, and caution is advised when interpreting BC measurements made with these methods.

179 Extraction of Coal-tar Pitch by Supercritical Carbon Dioxide ...

African Journals Online (AJOL)

Meyer

Several extractions of coal-tar pitch were performed using supercritical fluid ..... pressure and temperature, unlike exhaustive extraction, which involves a change in ... mechanism that is operative on extracting coal-tar pitch components with.

Gc/ms analysis of coal tar composition produced from coal

African Journals Online (AJOL)

Coal pyrolysis is one of the significant approaches for the comprehensive utilization ... planigraphy-GC/MS; therefore a satisfactory analytical result obtained, which .... Among the aliphatic group of the coal tar, the proportion of alkene is larger ...

Occupational coal tar dermatitis

Energy Technology Data Exchange (ETDEWEB)

Conde-Salazar, L; Guimaraens, D; Romero, L V; Gonzalez, M A

1987-04-01

The paper describes the allergic reaction to coal tar of a man handling it in a factory. The reaction appeared in the form of eczema on his trunk, arms and legs, but his hands were not affected as he had been wearing gloves. 1 ref.

Contact sensitivity to newsprint: a rare manifestation of coal tar allergy

Energy Technology Data Exchange (ETDEWEB)

Illchyshyn, A; Cartwright, P H; Smith, A G

1987-07-01

Contact dermatitis due to coal tar is infrequently reported in spite of the fact that it consists of a mixture of 10,000 constituents, and is still often used to treat both eczema and psoriasis. Discusses patient with coal tar sensitivity in whom the source of exacerbation of her dermatitis is shown to be newsprint, a common product containing coal tar-derived material. 6 refs.

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates

Energy Technology Data Exchange (ETDEWEB)

Bryer, P.J.; Scoggins, M.; McClintock, N.L. [Lamar University, Beaumont, TX (United States). Dept. of Biology

2010-05-15

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, & 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P < 0.0001) between treatments in addition to specific taxa responses, displaying a clear negative relationship with the amount of coal-tar sealant flake. These results support the hypothesis that coal-tar pavement sealants contain bioavailable PAHs that may harm aquatic environments.

Dermal uptake of polycyclic aromatic hydrocarbons after hairwash with coal-tar shampoo

Energy Technology Data Exchange (ETDEWEB)

Schooten, F.-J. van; Moonen, E.J.C.; Rhijnsburger, E.; Agen, B. van; Thijssen, H.H.W.; Kleinjans, J.C.S. [University of Limburg, Maastricht (Netherlands). Dept. of Health Risk Analysis and Toxicology

1994-11-26

Describes an experiment to assess the dermal uptake of polycyclic aromatic hydrocarbons (PAHs) after hairwashing with coal tar antidandruff shampoo. The urinary excretion of 1-hydroxypyrene (1-OH-P), a PAH metabolile was used to assess internal dose of PAH. A single use of coal tar shampoo resulted in increased 1-OH-P excretion in all members of the experimental group compared with the control group using a non-coal tar antidandruff shampoo. It is suggested that repeated use of coal tar shampoo would result in a high internal dose of carcinogenic PAH. 5 refs., 1 fig.

Composition of coal tar from pyrolysis and hydropyrolysis of Shenmu coal macerals

Energy Technology Data Exchange (ETDEWEB)

Sun, Q.; Li, W.; Chen, H.; Li, B. [Shandong Academy of Sciences, Jinan (China)

2005-08-15

To understand the relationship of the tar compositions and the coal macerals, the tars obtained from the pyrolysis and hydropyrolysis of Shenmu coal macerals in a fixed-bed reactor were analysed using GC-MS. And the effects of petrographic component, atmosphere and pressure on the yield of aromatic hydrocarbon, phenols, hydrocarbons, oxygen-containing heterocycle and PAHs were systematically investigated. The results show that there is great difference in the composition and the relative content of long chain hydrocarbons, aromatic hydrocarbons, phenols, oxygen-containing heterocycle and PAHs in tars from vitrinite and inertinite pyrolysis. Vitrinite tar contains high content of hydrocarbon with long chain, and inertinite tar contains high content of aromatic hydrocarbons, phenols, oxygen-containing heterocycle and PAHs. It suggests that vitrinite has lower aromaticity and longer chain in its structure than inertinite, which is in well agreement with the result from {sup 13}C NMR and FT-IR test. The tar yield of hydropyrolysis is higher than that of pyrolysis. With increasing the hydrogen pressure, the yield of tar increases greatly. The content of phenols and naphthalene in vitrinite tar form hydropyrolysis under 0.1 MPa is much lower than that form pyrolysis, while that of inertinite tar changes a little. The difference of tar compositions and relative content during pyrolysis and hydropyrolysis reflects the effect of hydrogenation and hydrocracking reactions and the structure characteristics of the macerals. 12 refs., 3 figs.

Ultrasound assisted, thermally activated persulfate oxidation of coal tar DNAPLs.

Science.gov (United States)

Peng, Libin; Wang, Li; Hu, Xingting; Wu, Peihui; Wang, Xueqing; Huang, Chumei; Wang, Xiangyang; Deng, Dayi

2016-11-15

The feasibility of ultrasound assisted, thermally activated persulfate for effective oxidation of twenty 2-6 ringed coal tar PAHs in a biphasic tar/water system and a triphasic tar/soil/water system were investigated and established. The results indicate that ultrasonic assistance, persulfate and elevated reaction temperature are all required to achieve effective oxidation of coal tar PAHs, while the heating needed can be provided by ultrasonic induced heating as well. Further kinetic analysis reveals that the oxidation of individual PAH in the biphasic tar/water system follows the first-order kinetics, and individual PAH oxidation rate is primary determined by the mass transfer coefficients, tar/water interfacial areas, the aqueous solubility of individual PAH and its concentration in coal tar. Based on the kinetic analysis and experimental results, the contributions of ultrasound, persulfate and elevated reaction temperature to PAHs oxidation were characterized, and the effects of ultrasonic intensity and oxidant dosage on PAHs oxidation efficiency were investigated. In addition, the results indicate that individual PAH degradability is closely related to its reactivity as well, and the high reactivity of 4-6 ringed PAHs substantially improves their degradability. Copyright © 2016 Elsevier B.V. All rights reserved.

21 CFR 740.18 - Coal tar hair dyes posing a risk of cancer.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 7 2010-04-01 2010-04-01 false Coal tar hair dyes posing a risk of cancer. 740.18... (CONTINUED) COSMETICS COSMETIC PRODUCT WARNING STATEMENTS Warning Statements § 740.18 Coal tar hair dyes... coal tar hair dye containing any ingredient listed in paragraph (b) of this section shall bear, in...

Relevance of carbon structure to formation of tar and liquid alkane during coal pyrolysis

International Nuclear Information System (INIS)

Liu, Peng; Le, Jiawei; Wang, Lanlan; Pan, Tieying; Lu, Xilan; Zhang, Dexiang

2016-01-01

Highlights: • Curve-fitting method was used to quantify the accurate contents of structural carbon. • Effect of carbon structure in coal with different rank on formation of pyrolysis tar was studied. • Numerical interrelation between carbon types in coal structure and tar yield is elaborated. • Effect of carbon structure on formation of liquid alkane during coal pyrolysis is discussed. - Abstract: The relevance of carbon structure to formation of tar and liquid alkane during coal pyrolysis were discussed extensively. The pyrolysis tests were carried out in a tube reactor at 873 K and keep 15 min. The carbon distribution in coals was investigated by solid state "1"3C nuclear magnetic resonance (N.M.R.). The curve-fitting method was used to quantify the accurate contents of structural carbon. The alkanes in coal tar were analyzed by Gas Chromatograph–Mass Spectrometer (GC–MS). The results show that oxygen-linked aromatic carbon decreases with the increasing of coal rank. The aliphatic carbon contents of Huainan (HN) coal are 44.20%, the highest among the four coals. The carbon types in coal structure have a significant influence on the formation of tar and liquid alkane. The coal tar yields are related to the aliphatic substituted aromatic carbon, CH_2/CH_3 ratio and oxygen-linked carbon in coal so that the increasing order of tar yield is Inner Mongolia lignite (IM, 6.30 wt.%) < Sinkiang coal (SK, 7.55 wt.%) < Shenmu coal (SM, 12.84 wt.%) < HN (16.29 wt.%). The highest contents of oxygen-linked aromatic carbon in IM lead to phenolic compound of 41.06% in IM-tar. The contents of alkane in SM-tar are the highest because the appropriate CH_2/CH_3 ratio and the highest aliphatic side chains on aromatic rings in SM leading to generate aliphatic hydrocarbon with medium molecular weight easily. The mechanism on formation of tar and liquid alkane plays an important role in guiding the industrialization of pyrolysis-based poly-generation producing tar with high

Assessment of ground-water contamination by coal-tar derivatives, St. Louis Park area, Minnesota

Science.gov (United States)

Hult, M.F.

1984-01-01

Operation of a coal-tar distillation and wood-preserving facility in St. Louis Park, Minnesota, during 1918-72 contaminated ground water with coal-tar derivatives and inorganic chemicals. Coal-tar derivatives entered the groundwater system through three major paths: (1) Spills and drippings that percolated to the water table, (2) surface runoff and plant process water that was discharged to wetlands south of the former plant site, and (3) movement of coal tar directly into bedrock aquifers through a multiaquifer well on the site.

29 CFR 1926.1102 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 8 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1926.1102 Section 1926.1102 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Hazardous Substances § 1926.1102 Coal tar pitch volatiles; interpretation of term. Note: The requirements...

GC/MS analysis of coal tar composition produced from coal pyrolysis

African Journals Online (AJOL)

Coal tar is a significant product generated from coal pyrolysis. A detailed analytical study on its composition and chemical structure will be of great advantage to its further processing and utilization. Using a combined method of planigraphy-gas chromatograph/mass spectroscopy (GC/MS), this work presents a composition ...

29 CFR 1915.1002 - Coal tar pitch volatiles; interpretation of term.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Coal tar pitch volatiles; interpretation of term. 1915.1002 Section 1915.1002 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH... Toxic and Hazardous Substances § 1915.1002 Coal tar pitch volatiles; interpretation of term. Note: The...

Cancer risk estimation for mixtures of coal tars and benzo(a)pyrene

International Nuclear Information System (INIS)

Gaylor, D.W.; Culp, S.J.; Goldstein, L.S.; Beland, F.A.

2000-01-01

Two-year chronic bioassays were conducted by using B6C3F1 female mice fed several concentrations of two different mixtures of coal tars from manufactured gas waste sites or benzo(a)pyrene (BaP). The purpose of the study was to obtain estimates of cancer potency of coal tar mixtures, by using conventional regulatory methods, for use in manufactured gas waste site remediation. A secondary purpose was to investigate the validity of using the concentration of a single potent carcinogen, in this case benzo(a)pyrene, to estimate the relative risk for a coal tar mixture. The study has shown that BaP dominates the cancer risk when its concentration is greater than 6,300 ppm in the coal tar mixture. In this case the most sensitive tissue site is the forestomach. Using low-dose linear extrapolation, the lifetime cancer risk for humans is estimated to be: Risk -4 (ppm coal tar in total diet) + 240 x 10 -4 (ppm BaP in total diet), based on forestomach tumors. If the BaP concentration in the coal tar mixture is less than 6,300 ppm, the more likely case, then lung tumors provide the largest estimated upper limit of risk, Risk -4 (ppm coal tar in total diet), with no contribution of BaP to lung tumors. The upper limit of the cancer potency (slope factor) for lifetime oral exposure to benzo(a)pyrene is 1.2 x 10 -3 per microg per kg body weight per day from this Good Laboratory Practice (GLP) study compared with the current value of 7.3 x 10 -3 per microg per kg body weight per day listed in the US EPA Integrated Risk Information System

Release of polyaromatic hydrocarbons from coal tar contaminated soils

International Nuclear Information System (INIS)

Priddy, N.D.; Lee, L.S.

1996-01-01

A variety of process wastes generated from manufactured gas production (MGP) have contaminated soils and groundwater at production and disposal sites. Coal tar, consisting of a complex mixture of hydrocarbons present as a nonaqueous phase liquid, makes up a large portion of MGP wastes. Of the compounds in coal tar, polyaromatic hydrocarbons (PAHs) are the major constituents of environmental concern due to their potential mutagenic and carcinogenic hazards. Characterization of the release of PAHs from the waste-soil matrix is essential to quantifying long-term environmental impacts in soils and groundwater. Currently, conservative estimates for the release of PAHs to the groundwater are made assuming equilibrium conditions and using relationships derived from artificially contaminated soils. Preliminary work suggests that aged coal tar contaminated soils have much lower rates of desorption and a greater affinity for retaining organic contaminants. To obtain better estimates of desorption rates, the release of PAHs from a coal tar soil was investigated using a flow-interruption, miscible displacement technique. Methanol/water solutions were employed to enhance PAH concentrations above limits of detection. For each methanol/water solution employed, a series of flow interrupts of varying times was invoked. Release rates from each methanol/water solution were estimated from the increase in concentration with duration of flow interruption. Aqueous-phase release rates were then estimated by extrapolation using a log-linear cosolvency model

Carbazole is a naturally occurring inhibitor of angiogenesis and inflammation isolated from antipsoriatic coal tar

Energy Technology Data Exchange (ETDEWEB)

Jack L. Arbiser; Baskaran Govindarajan; Traci E. Battle; Rebecca Lynch; David A. Frank; Masuko Ushio-Fukai; Betsy N. Perry; David F. Stern; G. Tim Bowden; Anquan Liu; Eva Klein; Pawel J. Kolodziejski; N. Tony Eissa; Chowdhury F. Hossain; Dale G. Nagle [Emory University School of Medicine, Atlanta, GA (United States). Department of Dermatology

2006-06-15

Coal tar is one of the oldest and an effective treatment for psoriasis. Coal tar has been directly applied to the skin, or used in combination with UV light as part of the Goeckerman treatment. The use of coal tar has caused long-term remissions in psoriasis, but has fallen out of favor because the treatment requires hospitalization and coal tar is poorly acceptable aesthetically to patients. Thus, determining the active antipsoriatic component of coal tar is of considerable therapeutic interest. We fractionated coal tar into its components, and tested them using the SVR angiogenesis inhibitor assay. Treatment of SVR endothelial cells with coal tar fractions resulted in the isolation of a single fraction with antiangiogenic activity. The active antiangiogenic compound in coal tar is carbazole. In addition to antiangiogenic activity, carbazole inhibited the production of inflammatory IL-15 by human mononuclear cells. IL-15 is elevated in psoriasis and is thought to contribute to psoriatic inflammation. Carbazole treatment also reduced activity of inducible nitric oxide synthase (iNOS), which is proinflammatory and elevated in psoriasis. The effect of carbazole on upstream pathways in human psoriasis was determined, and carbazole was shown to inhibit signal transducer and activator of transcription (stat)3-mediated transcription, which has been shown to be relevant in human psoriasis. IL-15, iNOS, and stat3 activation require the activation of the small GTPase rac for optimal activity. Carbazole was found to inhibit rac activation as a mechanism for its inhibition of downstream inflammatory and angiogenic pathways. Given its antiangiogenic and anti-inflammatory activities, carbazole is likely a major component of the antipsoriatic activity of coal tar. Carbazole and derivatives may be useful in the therapy of human psoriasis.

Coliquefaction of coal, tar sand bitumen and plastic (interaction among coal, bitumen and plastic); Sekitan/tar sand bitumen/plastic no kyoekika ni okeru kyozon busshitsu no eikyo

Energy Technology Data Exchange (ETDEWEB)

Yamaguchi, H.; Okuyama, Y.; Matsubara, K. [NKK Corp., Tokyo (Japan); Kamo, T.; Sato, Y. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

For the improvement of economy, coliquefaction of coal, tar sand bitumen and plastic was performed under low hydrogen pressure, to investigate the influence of interaction among these on the liquefaction characteristics. For comparison, coliquefaction was also performed under the hydrogen pressure same as the NEDOL process. In addition, for clarifying its reaction mechanism, coliquefaction of dibenzyl and plastic was performed as a model experiment, to illustrate the distribution of products and composition of oil, and to discuss the interaction between dibenzyl and various plastics, and between various plastics. Under direct coal liquefaction conditions, coprocessing of Tanito Harum coal, Athabasca tar sand and plastic was carried out under low hydrogen pressure with an autoclave. The observed value of oil yield was higher than the calculated value based on the values from separate liquefaction of coal and plastic, which suggested the interaction between coal and the mixed plastic. The results of coliquefaction of coal, tar sand bitumen and plastic could be explained from the obtained oil yield and its composition by the coliquefaction of dibenzyl and plastic. 2 refs., 3 tabs.

Estimating release of polycyclic aromatic hydrocarbons from coal tar at manufactured-gas plant sites

International Nuclear Information System (INIS)

Loehr, R.C.; Rao, P.S.C.; Lee, L.S.; Okuda, I.

1992-08-01

One component of the EPRI's research on Envirorunental Behavior of Organic Substances (EBOS) consists of developing information and models to predict releases of monocyclic and polycyclic aromatic hydrocarbons (MAHs and PAHs) to groundwater from coal tars and contaminated soils at MGP sites. The results of this report focus primarily on release of PAHs from coal tars. There are at least two approaches to predicting the release of organic chemicals from coal tar to water. The simplest method to estimate aqueous concentrations is to assume that water solubility of a PAH compound released from the tar can be defined by equilibrium precipitation-dissolution reactions. Application of Raoult's law is another method to predict aqueous concentrations, which requires the assumption of ''ideal'' behavior for partitioning of PAHs between the tar and water phases. To evaluate the applicability of these two methods for predicting PAH releases, laboratory experiments were conducted with eight coal tar samples from former MGP sites across the country. Migration of chemicals in the environment and resulting contaminant plumes in groundwater are determined by leachate concentrations of the chemicals. The use of equilibrium precipitation-dissolution reactions will usually result in an overestimation of PAH concentrations in the leachate from a coal tar source, and thus the resulting PAH concentrations in groundwater. Raoult's law appears to be a more accurate approach to predicting the release of several PAHs from coal tars. Furthermore, if nonequilibrium conditions prevail, aqueous-phase PAH concentrations will be even lower than those predicted using Raoult's law

Comparative assessment of coal tars obtained from 10 former manufactured gas plant sites in the eastern United States

Energy Technology Data Exchange (ETDEWEB)

Brown, D.G.; Gupta, L.; Kim, T.H.; Moo-Young, H.K.; Coleman, A.J. [Lehigh University, Bethlehem, PA (United States). Dept. of Civil & Environmental Engineering

2006-11-15

A comparative analysis was performed on eleven coal tars obtained from former manufactured gas plant sites in the eastern United States. Bulk properties analyzed included percent ash, Karl Fisher water content, viscosity and average molecular weight. Chemical properties included monocyclic- and polycyclic-aromatic hydrocarbon (PAH) concentrations, alkylated aromatic concentrations, and concentrations of aliphatic and aromatic fractions. It was found that there was at least an order-of-magnitude variation in all properties measured between the eleven coal tars. Additionally, two coal tars obtained from the same manufactured gas plant site had very different properties, highlighting that there can be wide variations in coal tar properties from different samples obtained from the same site. Similarities were also observed between the coal tars. The relative chemical distributions were similar for all coal tars, and the coal tars predominantly consisted of PAHs, with naphthalene being the single-most prevalent compound. The C{sub 9-22} aromatic fraction, an indicator of all PAHs up to a molecular weight of approximately 276 g mole{sup -1}, showed a strong power-law relationship with the coal tar average molecular weight (MWct). And the concentrations of individual PAHs decreased linearly as MWct increased up to ca. 1000 g mole{sup -1}, above which they remained low and variable. Implications of these properties and their variation with MWct on groundwater quality are discussed. Ultimately, while these similarities do allow generalities to be made about coal tars, the wide range of coal tar bulk and chemical properties reported here highlights the complex nature of coal tars.

Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel

Directory of Open Access Journals (Sweden)

Didi Dwi Anggoro

2017-05-01

Full Text Available One of many efforts to convert coal tar into alternative liquid fuel is by hydrocracking. This research aims to determine the impregnation of Co-Mo/Y zeolite, its characteristics, the effect of impregnation temperature and time, and also the best Co-Mo/Y zeolite impregnation condition for the conversion of coal tar. This research was conducted in several steps, impregnating Co from Co(NO32.6H2O and Mo from (NH46Mo7O24.4H2O into Zeolite Y in liquid media, drying at 100 °C for 24 hours, and calcination at 550 °C for 3 hours. Coal tar was then reacted with hydrogen gas (as a reactant, and Co-Mo/Zeolite Y (as a catalyst was conducted at 350 °C. Characteristic analysis showed that Co and Mo had impregnated into the Y zeolite, as well as it made no change of catalyst’s structure and increased the total acidity. The higher of impregnation temperature was increased the catalyst crystallinity, total acidity, and yield of gasoline. The longer impregnation time was reduced crystallinity value, but total acidity and yield were increased. GC analysis showed that products included into the gasoline product (C8, C9, and C10. Copyright © 2017 BCREC Group. All rights reserved Received: 13rd November 2016; Revised: 12nd February 2017; Accepted: 16th February 2017 How to Cite: Anggoro, D.D., Buchori, L., Silaen, G.C., Utami, R.N. (2017. Preparation, Characterization, and Activation of Co-Mo/Y Zeolite Catalyst for Coal Tar Conversion to Liquid Fuel. Bulletin of Chemical Reaction Engineering & Catalysis, 12 (2: 219-226 (doi:10.9767/bcrec.12.2.768.219-226 Permalink/DOI: http://dx.doi.org/10.9767/bcrec.12.2.768.219-226

The purification of coal tar by the addition of quinoline and Zn(oh)/sub 2/

International Nuclear Information System (INIS)

Zhou, P.; Chen, Q.L.; Ao, X.Q.; Kang, C

2017-01-01

The coal tar was purified by the addition of quinoline and Zn(OH)2, in order to decrease the content of carbon and inorganic oxide particles. The effect on the viscosity and ash content of the coal tar were investigated by altering temperature, time, and the amount of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 20:1 and the static time was 24 h. The viscosity of three layers decreased with rising temperature. When the static temperature and time was 45 °C and 24 h, respectively. The viscosity of three layers decreased with the arising amount of quinoline. And when the volume ratio between quinolone and coal tar was 20:1 and the temperature was 45 °C. The viscosity of three layers decreased first and then increased with the prolonging of static time. And when the static time of coal tar was 24 h, the viscosity of coal tar is the lowest. Because of the lower viscosity of coal tar, decreasing the content of carbon and ash particles in upper and middle layer, the ash content decreased from 0.168% to 0.092%. The addition of Zn(OH)2 can lead ash content in middle layer decrease to 0.058%. Zn2SiO4 and ZnAl2O4 may be produced due to the reaction between Zn (OH) 2 and SiO2 or Al2O3, which can settle down easily. The results show that the content of carbon and inorganic oxide particles in upper-middle-class (the middle 4/5 of the whole volume) decreased with the addition of quinolone and Zn(OH)2 . When the volume ratio between quinolone and coal tar was 50:2, quality ratio between coal tar and Zn(OH)2 was 20000:1, the mixture were heated up to 45 °C at atmospheric pressure and keeping this constant temperature for 24 h, the ash content in upper-middle-class can decreased to 0.058%. (author)

Material Properties and Characteristics for Development of an Expert System for Coal-Tar Sealers

National Research Council Canada - National Science Library

Shoenberger, James

2001-01-01

.... Several coal-tar mixtures that varied with source of the coal-tar emulsion, amount of aggregate, and amount of polymer used in the mixtures were evaluated for their field performance and material properties...

Toxicity of coal-tar and asphalt sealants to eastern newts, Notophthalmus viridescens

Energy Technology Data Exchange (ETDEWEB)

Bommarito, T.; Sparling, D.W.; Halbrook, R.S. [South Illinois University, Carbondale, IL (United States). Cooperative Wildlife Research Laboratory

2010-09-15

Between 1970 and 2000 the concentration of total polycyclic aromatic hydrocarbons (TPAH) in several lakes across the country increased whereas those of other persistent organic pollutants (POPs) tended to remain stable or declined. Urbanized watersheds experienced greater rises in TPAH concentration compared to non-urban lakes. Sources for urban PAHs include industrial wastes, vehicular exhausts and oil leaks and sealants from pavement surfaces. Both coal-tar and asphalt sealants are used to protect surfaces but runoff from surfaces coated with coal-tar can have mean concentrations of 3500 mg TPAHs kg{sup -1}, much higher than runoff from asphalt-sealed or cement surfaces. Unaltered parent compounds of PAHs can have many lethal and sublethal toxic effects, but oxidation and UV radiation can alter the toxicity of these compounds, sometimes creating degradates that are many times more toxic than parent compounds. The purposes of this study were to determine if coal-tar sealants can be toxic to adult eastern newts (Notophthalmus viridescens) and to compare the toxicity of coal-tar sealant to that of asphalt sealant. Newts were exposed to sediments containing dried sealants ranging from 0 mg kg{sup -1} to 1500 mg kg{sup -1} under simultaneous exposure to UV radiation and visible light to determine concentration/response relationships. No significant mortality occurred with any treatment. Significant effects due to sealants included decreased righting ability and diminished liver enzyme activities. Coal-tar sealant was more effective in inducing these changes than was asphalt sealant.

Skin cancer in patients with psoriasis treated with coal tar. A 25-year follow-up study

International Nuclear Information System (INIS)

Pittelkow, M.R.; Perry, H.O.; Muller, S.A.; Maughan, W.Z.; O'Brien, P.C.

1981-01-01

For many years, crude coal tar has been used for the treatment of psoriasis. The possible carcinogenic effect of crude coal tar and ultraviolet (UV) radiation (Goeckerman regimen), considered individually or in combination, has been of some concern to physicians. A 25-year follow-up study was completed on 280 patients with psoriasis who were hospitalized and treated with crude coal tar and UV radiation at the Mayo Clinic, Rochester, Minn, during the years 1950 through 1954. The results of this study suggest that the incidence of skin cancer is not appreciably increased above the expected incidence for the general population when patients are treated with coal tar ointments. It seems that the Goeckerman regimen (topical crude coal tar combined with UV radiation) can be used with minimal risk for skin cancer in the treatment of psoriasis

Flash hydropyrolysis of bituminous coal . III. Research on flash hydropyrolysis tar

Energy Technology Data Exchange (ETDEWEB)

Dong, M.; Zhu, Z.; He, Y.; Ding, N.; Tang, L. [East China University of Science and Technology, Shanghai (China)

2000-02-01

Tar sample obtained by flash hydropyrolysis (FHP) from Dongshen coal at high pressure entrained reactor was investigated. An effect of flash hydropyrolysis temperature on the main components in tar was studied and the quality of the tar was compared with high temperature coke oven tar. The results showed that: the yields of liquid hydrocarbon in FHP tar were more than 15%, which is twofold of that in coke oven tar; the FHP tar has high oil fraction and low pitch; high phenol components and pure condensed polycyclic aromatic hydrocarbon, and low aliphatic hydrocarbon. The components of the FHP tar were simpler than that of high temperature coke oven tar. Therefore, FHP has improved the quantity and quality of tar. 11 refs., 3 figs., 5 tabs.

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH8) in the 0.03-m samples above sealed lots (1320 ng m-3) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m-3). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m-3) was five times greater than above unsealed lots (26.0 ng m-3). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m-2 h-1, respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces.

Investigation of sulfur-polycyclic aromatic hydrocarbon in coal derived tars of pyrolysis and hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Chen, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

1999-07-01

A study was undertaken to characterize sulphur forms in coal derived tars from pyrolysis and hydropyrolysis of bituminous coal and lignite. The pyrolysis tars were analyzed for content of polycyclic aromatic sulfur hydrocarbons (PASH). 5 refs., 3 figs., 3 tabs.

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement.

Science.gov (United States)

Van Metre, Peter C; Majewski, Michael S; Mahler, Barbara J; Foreman, William T; Braun, Christopher L; Wilson, Jennifer T; Burbank, Teresa L

2012-06-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, are a potential source of volatile PAHs to the atmosphere. An initial assessment of volatilization of PAHs from coal-tar-sealed pavement is presented here in which we measured summertime gas-phase PAH concentrations 0.03 m and 1.28 m above the pavement surface of seven sealed (six with coal-tar-based sealant and one with asphalt-based sealant) and three unsealed (two asphalt and one concrete) parking lots in central Texas. PAHs also were measured in parking lot dust. The geometric mean concentration of the sum of eight frequently detected PAHs (ΣPAH(8)) in the 0.03-m samples above sealed lots (1320 ng m(-3)) during the hottest part of the day was 20 times greater than that above unsealed lots (66.5 ng m(-3)). The geometric mean concentration in the 1.28-m samples above sealed lots (138 ng m(-3)) was five times greater than above unsealed lots (26.0 ng m(-3)). Estimated PAH flux from the sealed lots was 60 times greater than that from unsealed lots (geometric means of 88 and 1.4 μg m(-2) h(-1), respectively). Although the data set presented here is small, the much higher estimated fluxes from sealed pavement than from unsealed pavement indicate that coal-tar-based sealants are emitting PAHs to urban air at high rates compared to other paved surfaces. Published by Elsevier Ltd.

Coal-tar based pavement sealant toxicity to freshwater macroinvertebrates.

Science.gov (United States)

Bryer, Pamela J; Scoggins, Mateo; McClintock, Nancy L

2010-05-01

Non-point-source pollution is a major source of ecological impairment in urban stream systems. Recent work suggests that coal-tar pavement sealants, used extensively to protect parking areas, may be contributing a large portion of the polycyclic aromatic hydrocarbon (PAH) loading seen in urban stream sediments. The hypothesis that dried coal-tar pavement sealant flake could alter the macroinvertebrate communities native to streams in Austin, TX was tested using a controlled outdoor laboratory type approach. The treatment groups were: control, low, medium, and high with total PAH concentrations (TPAH = sum of 16 EPA priority pollutant PAHs) of 0.1, 7.5, 18.4, & 300 mg/kg respectively. The low, medium, and high treatments were created via the addition of dried coal-tar pavement sealant to a sterile soil. At the start of the 24-day exposure, sediment from a minimally impacted local reference site containing a community of live sediment-dwelling benthic macroinvertebrates was added to each replicate. An exposure-dependent response was found for several stream health measures and for several individual taxa. There were community differences in abundance (P = 0.0004) and richness (P pavement sealants contain bioavailable PAHs that may harm aquatic environments. Copyright 2009 Elsevier Ltd. All rights reserved.

No Increased Risk of Cancer after Coal Tar Treatment in Patients with Psoriasis or Eczema

NARCIS (Netherlands)

Roelofzen, Judith H. J.; Aben, Katja K. H.; Oldenhof, Ursula T. H.; Coenraads, Pieter-Jan; Alkemade, Hans A.; van de Kerkhof, Peter C. M.; van der Valk, Pieter G. M.; Kiemeney, Lambertus A. L. M.

Coal tar is an effective treatment for psoriasis and eczema, but it contains several carcinogenic compounds. Occupational and animal studies have shown an increased risk of cancer after exposure to coal tar. Many dermatologists have abandoned this treatment for safety reasons, although the risk of

Abating coal tar seepage into surface water bodies using sheet piles with sealed interlocks

International Nuclear Information System (INIS)

Collingwood, B.I.; Boscardin, M.D.; Murdock, R.F.

1995-01-01

A former coal tar processing facility processed crude coal tar supplied from manufactured gas plants in the area. Coal-tar-contaminated ground water from the site was observed seeping through an existing timber bulkhead along a tidal river and producing a multicolored sheen on the surface of the river. As part of a short-term measure to abate the seepage into the river, 64-m long anchored sheet pile wall with sheet pile wing walls at each end was constructed inland of the of the timber bulkhead. The sheet piles extended to low-permeability soils at depth and the interlocks of the sheet piles were provided with polyurethane rubber seals. Based on postconstruction observations for leakage and sheens related to leakage, the steel sheet piles with polyurethane rubber interlock seals appeared to provide a successful seal and abate coal-tar-contaminated ground water seepage into the river. The tie rod penetration sealing proved to be a more problematic detail, but through several postconstruction grouting episodes, an effective seal was produced

Anomalous capillary flow of coal tar pitches

Energy Technology Data Exchange (ETDEWEB)

Saint Romain, J.L.; Lahaye, J.; Ehrburger, P.; Couderc, P.

1986-06-01

Capillary flow of liquid coal tar pitch into a coke bed was studied. Anomalies in the flow could not be attributed to a plugging effect for mesophase content lower than 20 wt%. The flow behaviour of small pitch droplets can be correlated with the change in physicochemical properties, as measured by the glass transition temperature, on penetration into the coke bed. 4 references.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

International Nuclear Information System (INIS)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. - Highlights: • We compare PAH and azaarene concentrations in runoff from coal-tar- and asphalt-sealed pavement. • Concentrations in coal-tar-sealcoat runoff greatly exceeded those in asphalt-sealcoat runoff. • Decreases in azaarenes and LMW PAHs were offset by increases in HMW PAHs. • PAH concentrations in coal-tar-sealcoat runoff remained high for months after application. - Concentrations of PAHs in runoff from pavement with coal-tar-based sealcoat continue to be elevated for at least 3 months following sealcoat application

Analysis of the use of coal tar as a binder in bituminous mixtures, using Marshall and Ramcodes methodologies

International Nuclear Information System (INIS)

Ochoa-Díaz, R

2013-01-01

This paper presents an alternative use of coal tar, a by-product of the steel industry, given the problems of accumulation and negative environmental impact. Therefore, it is necessary to analyze the incorporation of coal tar as a binder in paving mixtures. First, this paper presents the origin, description of the main characteristics, and properties of tar. Then, this paper evaluates the mix of coal tar by means of the RAMCODES and Marshall methodologies to determine its resistance. The results of the tests explain the physical and mechanical properties of the mix. Taking into account the results of both methods, this paper makes a comparison to determine the suitability of the RAMCODES methodology in the mix design. Finally, it analyzes the alternatives to coal tar that can be used as binders in bituminous mixes for pavement and the advantages of their uses under some specific conditions

UTILIZATION OF ACTIVATED ZEOLITE AS MOLECULAR SIEVE IN CHROMATOGRAPHIC COLUMN FOR SEPARATION OF COAL TAR COMPOUNDS

Directory of Open Access Journals (Sweden)

Dwi Retno Nurotul Wahidiyah

2010-06-01

Full Text Available Application of activated zeolite (ZAA as molecular sieve to separate compounds of coal tar from vaccum fractional distillation, have been done. The size of zeolite was 10-20 mesh and used as solid phase in column chromatography with length of 30 cm. The first step of the research was coal pyrolisis and the product (tar was distillated by fractional column and vaccum system at reduced pressure 44 cmHg and maximum temperature at 200 oC. The distillate from this procedure was flowed to the column chromatography of zeolite (ZAA. The compound absorbed by zeolite was eluted with varying solvents, i.e: CCl4, acetone and ethanol. Each fraction was then analyzed by gas chromatography. The results showed, zeolite have a capability to separate the compounds of tar and it tends to absorb medium hydrocarbon. The nonpolar eluent [CCl4] gives the better result in eluting tar compound than polar (ethanol or medium polar eluents (acetone.   Keywords: zeolite, coal tar, column chromatography

Characterization of acid tars

Energy Technology Data Exchange (ETDEWEB)

Leonard, Sunday A., E-mail: sunday.leonard@ucl.ac.uk [Department of Civil Environmental and Geomatic Engineering, University College London, Chadwick Building, Gower Street, London, WC1E 6BT (United Kingdom); Stegemann, Julia A. [Department of Civil Environmental and Geomatic Engineering, University College London, Chadwick Building, Gower Street, London, WC1E 6BT (United Kingdom); Roy, Amitava [J. Bennett Johnston, Sr., Centre for Advance Microstructures and Devices (CAMD), 6980 Jefferson Highway, Louisiana State University, Baton Rouge, LA, 70806 (United States)

2010-03-15

Acid tars from the processing of petroleum and petrochemicals using sulfuric acid were characterized by gas chromatography/mass spectrometry (GC/MS), inductively coupled plasma/optical emission spectrometry (ICP/OES), differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectrometry, and scanning electron microscopy/energy dispersive X-ray (SEM/EDX) micro-analysis. Leaching of contaminants from the acid tars in 48 h batch tests with distilled water at a liquid-to-solid ratio 10:1 was also studied. GC/MS results show that the samples contained aliphatic hydrocarbons, cyclic hydrocarbons, up to 12 of the 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs), and numerous other organic groups, including organic acids (sulfonic acids, carboxylic acids and aromatic acids), phenyl, nitrile, amide, furans, thiophenes, pyrroles, and phthalates, many of which are toxic. Metals analysis shows that Pb was present in significant concentration. DSC results show different transition peaks in the studied samples, demonstrating their complexity and variability. FTIR analysis further confirmed the presence of the organic groups detected by GC/MS. The SEM/EDX micro-analysis results provided insight on the surface characteristics of the samples and show that contaminants distribution was heterogeneous. The results provide useful data on the composition, complexity, and variability of acid tars; information which hitherto have been scarce in public domain.

Characterization of acid tars

International Nuclear Information System (INIS)

Leonard, Sunday A.; Stegemann, Julia A.; Roy, Amitava

2010-01-01

Acid tars from the processing of petroleum and petrochemicals using sulfuric acid were characterized by gas chromatography/mass spectrometry (GC/MS), inductively coupled plasma/optical emission spectrometry (ICP/OES), differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectrometry, and scanning electron microscopy/energy dispersive X-ray (SEM/EDX) micro-analysis. Leaching of contaminants from the acid tars in 48 h batch tests with distilled water at a liquid-to-solid ratio 10:1 was also studied. GC/MS results show that the samples contained aliphatic hydrocarbons, cyclic hydrocarbons, up to 12 of the 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs), and numerous other organic groups, including organic acids (sulfonic acids, carboxylic acids and aromatic acids), phenyl, nitrile, amide, furans, thiophenes, pyrroles, and phthalates, many of which are toxic. Metals analysis shows that Pb was present in significant concentration. DSC results show different transition peaks in the studied samples, demonstrating their complexity and variability. FTIR analysis further confirmed the presence of the organic groups detected by GC/MS. The SEM/EDX micro-analysis results provided insight on the surface characteristics of the samples and show that contaminants distribution was heterogeneous. The results provide useful data on the composition, complexity, and variability of acid tars; information which hitherto have been scarce in public domain.

Characterization of acid tar waste from benzol purification | Danha ...

African Journals Online (AJOL)

The use of concentrated sulphuric acid to purify benzene, toluene and xylene produces acidic waste known as acid tar. The characterization of the acid tar to determine the composition and physical properties to device a way to use the waste was done. There were three acid tars two from benzene (B acid tar), toluene and ...

PAH volatilization following application of coal-tar-based pavement sealant

Science.gov (United States)

Van Metre, Peter C.; Majewski, Michael S.; Mahler, Barbara J.; Foreman, William T.; Braun, Christopher L.; Wilson, Jennifer T.; Burbank, Teresa L.

2012-01-01

Coal-tar-based pavement sealants, a major source of PAHs to urban water bodies, have recently been identified as a source of volatile PAHs to the atmosphere. We tracked the volatilization of PAHs for 1 year after application of a coal-tar-based pavement sealant by measuring gas-phase PAH concentrations above the pavement surface and solid-phase PAH concentrations in sealant scraped from the surface. Gas-phase concentrations at two heights (0.03 and 1.28 m) and wind speed were used to estimate volatilization flux. The sum of the concentrations of eight frequently detected PAHs (ΣPAH8) in the 0.03-m sample 1.6 h after application (297,000 ng m-3) was about 5000 times greater than that previously reported for the same height above unsealed parking lots (66 ng m-3). Flux at 1.6 h after application was estimated at 45,000 μg m-2 h-1 and decreased rapidly during the 45 days after application to 160 μg m-2 h-1. Loss of PAHs from the adhered sealant also was rapid, with about a 50% decrease in solid-phase ΣPAH8 concentration over the 45 days after application. There was general agreement, given the uncertainties, in the estimated mass of ΣPAH8 lost to the atmosphere on the basis of air sampling (2–3 g m-2) and adhered sealant sampling (6 g m-2) during the first 16 days after application, translating to a loss to the atmosphere of one-quarter to one-half of the PAHs in the sealcoat product. Combining the estimated mass of ΣPAH8 released to the atmosphere with a national-use estimate of coal-tar-based sealant suggests that PAH emissions from new coal-tar-based sealcoat applications each year (~1000 Mg) are larger than annual vehicle emissions of PAHs for the United States.

Mineral oils, tars. [British patent

Energy Technology Data Exchange (ETDEWEB)

O' Brien, A M; Handmarch, E

1933-08-11

Hydrocarbon materials such as mineral oils and tars from coal, shale, lignite, or peat are freed from phenols and like oxy-bodies by heating under pressure in a closed vessel to a temperature and for a time sufficient to effect reduction of the oxy-bodies, and then removing the water formed by the reaction. 350/sup 0/ to 400/sup 0/C. for 30 to 60 minutes is suitable. Any wax-like constituents are converted to liquids of lower viscosity and settling point. The product may be fractionated to give light oils and a residue of aviation Diesel fuel. In an example, oil from the low-temperature distillation of coal and having a tar acid content of 30 per cent is treated in a tubular converter at 380/sup 0/C. and 400 lb. per sq. in for 40 min., and the benzine toluol, and xylol distilled; the residue has a tar acid content of only 7.6 per cent.

Coal-tar-based sealcoated pavement: A major PAH source to urban stream sediments

International Nuclear Information System (INIS)

Witter, Amy E.; Nguyen, Minh H.; Baidar, Sunil; Sak, Peter B.

2014-01-01

We used land-use analysis, PAH concentrations and assemblages, and multivariate statistics to identify sediment PAH sources in a small (∼1303 km 2 ) urbanizing watershed located in South-Central, Pennsylvania, USA. A geographic information system (GIS) was employed to quantify land-use features that may serve as PAH sources. Urban PAH concentrations were three times higher than rural levels, and were significantly and highly correlated with combined residential/commercial/industrial land use. Principal components analysis (PCA) was used to group sediments with similar PAH assemblages, and correlation analysis compared PAH sediment assemblages to common PAH sources. The strongest correlations were observed between rural sediments (n = 7) and coke-oven emissions sources (r = 0.69–0.78, n = 5), and between urban sediments (n = 22) and coal-tar-based sealcoat dust (r = 0.94, n = 47) suggesting that coal-tar-based sealcoat is an important urban PAH source in this watershed linked to residential and commercial/industrial land use. -- Highlights: • Total PAH concentrations were measured at 35 sites along an urbanizing land-use gradient. • PAH concentrations increased with increasing urban land-use. • Urban land-use metrics were measured at three spatial scales using GIS. • PAH assemblages indicate coal-tar-based sealcoat is a major urban PAH source. • PAH assemblages indicate coke-oven emissions are an important rural PAH source. -- Coal-tar-based sealcoated pavement is a major PAH source to urban freshwater stream sediments in south-central Pennsylvania, USA

Dehydration of hydrated low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Yoshida, T

1949-01-01

Yoshida examined the mechanism of the dehydration of hydrated low-temperature tar with a microscope. The tar containing free carbon and coal dust is so stable that the removal of the above substances and water by a physical method is very difficult. Addition of light oil produced by fractionation of low-temperature tar facilitates the operations. Yoshida tried using the separate acid, neutral, and basic components of the light oil; the acid oil proved to be most effective. For many reasons it is convenient to use light oil as it is. In this method the quantity of light oil required is 2 to 3 times that of tar. But in supplementing the centrifugal method, the quantity of light oil needed might be only half the amount of tar.

Characterisation and catalytic upgrading of tars from coal-tyre hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mastral, A.M.; Murillo, R.; Callen, M.S.; Garcia, T. [Instituto de Carboquimica, Zaragoza (Spain)

1999-07-01

Tars from coal-tyre hydropyrolysis obtained in a swept fixed bed reactor were upgraded with catalysts. Upgraded oils were characterized, and naphtha, kerosene, gas oil, heavy gas oil and vacuum residue percentages were quantified. 7 refs., 3 tabs.

Low-temperature tar from bituminous coal and its further treatment

Energy Technology Data Exchange (ETDEWEB)

Hansen, C J

1950-01-01

High-temperature carbonization of bituminous coal yields only 3 to 4 percent tar, as compared with 8 to 10 percent or even more for low-temperature carbonization. The yield of phenols is 20 to 30 times as great from the low-temperature tar. Five conditions that must be met by a satisfactory low-temperature carbonization process are listed. The only method that satisfies all of these conditions is the Brennstoff-Technik (BT) process, in which iron retorts with movable walls are used. One disadvantage of most of the other processes is the high-pitch content of the tar. These tars are processed further to a neutral oil and a phenol-containing oil which are good diesel fuels with high-cetane numbers; the neutral oil can be fractionated to give oils of high-, medium-, and low-cetane number. Attempts to fractionate the tar oil by solvents have not proved commercially useful. However, the tar can be diluted with low-temperature light oil and phenols extracted with NaOH solution without distillation. Some difficulty is found, owing to the simultaneous extraction of viscous resins and other products that are readily removed from the phenols by distillation.

Process from removing benzine, toluene, etc. , from petroleum residues, coal tar, and shale tar, etc

Energy Technology Data Exchange (ETDEWEB)

Hlawaty, F

1888-08-11

A process is described for the preparation of ligroin and its homologs as well as naphthalene and anthracene consisting in leading superheated water vapor into a mixture of petroleum residues (or mineral coal tar, etc.) heated to about 400/sup 0/C with cellulosic substances as sage shreds, sea grass, or straw, with addition of caustic alkali.

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management.

Science.gov (United States)

Mahler, Barbara J; Metre, Peter C Van; Crane, Judy L; Watts, Alison W; Scoggins, Mateo; Williams, E Spencer

2012-03-20

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments-including stormwater runoff, lake sediment, soil, house dust, and most recently, air-contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Coal-tar-based pavement sealcoat and PAHs: implications for the environment, human health, and stormwater management

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.; Crane, Judy L.; Watts, Alison W.; Scoggins, Mateo; Williams, E. Spencer

2012-01-01

Coal-tar-based sealcoat products, widely used in the central and eastern U.S. on parking lots, driveways, and even playgrounds, are typically 20-35% coal-tar pitch, a known human carcinogen that contains about 200 polycyclic aromatic hydrocarbon (PAH) compounds. Research continues to identify environmental compartments—including stormwater runoff, lake sediment, soil, house dust, and most recently, air—contaminated by PAHs from coal-tar-based sealcoat and to demonstrate potential risks to biological communities and human health. In many cases, the levels of contamination associated with sealed pavement are striking relative to levels near unsealed pavement: PAH concentrations in air over pavement with freshly applied coal-tar-based sealcoat, for example, were hundreds to thousands of times higher than those in air over unsealed pavement. Even a small amount of sealcoated pavement can be the dominant source of PAHs to sediment in stormwater-retention ponds; proper disposal of such PAH-contaminated sediment can be extremely costly. Several local governments, the District of Columbia, and the State of Washington have banned use of these products, and several national and regional hardware and home-improvement retailers have voluntarily ceased selling them.

Coal-tar pavement sealants might substantially increase children's PAH exposures

Science.gov (United States)

Williams, E. Spencer; Mahler, Barbara J.; Van Metre, Peter C.

2012-01-01

Dietary ingestion has been identified repeatedly as the primary route of human exposure to polycyclic aromatic hydrocarbons (PAHs), seven of which are classified as probable human carcinogens (B2 PAHs) by the U.S. EPA. Humans are exposed to PAHs through ingestion of cooked and uncooked foods, incidental ingestion of soil and dust, inhalation of ambient air, and absorption through skin. Although PAH sources are ubiquitous in the environment, one recently identified PAH source stands out: Coal-tar-based pavement sealant—a product applied to many parking lots, driveways, and even playgrounds primarily in the central, southern, and eastern U.S.—has PAH concentrations 100–1000 times greater than most other PAH sources. It was reported recently that PAH concentrations in house dust in residences adjacent to parking lots with coal-tar-based sealant were 25 times higher than in residences adjacent to unsealed asphalt parking lots.

PAHs underfoot: Contaminated dust from coal-tar sealcoated pavement is widespread in the United States

Science.gov (United States)

Van Metre, P.C.; Mahler, B.J.; Wilson, J.T.

2009-01-01

We reported in 2005 that runoff from parking lots treated with coal-tar-based sealcoat was a major source of polycyclic aromatic hydrocarbons (PAHs) to streams in Austin, Texas. Here we present new data from nine U. S. cities that show nationwide patterns in concentrations of PAHs associated with sealcoat Dust was swept from parking lots in six cities in the central and eastern U. S., where coal-tar-based sealcoat dominates use, and three cities in the western U. S., where asphalt-based sealcoat dominates use. For six central and eastern cities, median ?? PAH concentrations in dust from sealcoated and unsealcoated pavement are 2200 and 27 mg/kg, respectively. For three western cities, median ?? PAH concentrations in dust from sealcoated and unsealcoated pavement are similar and very low (2. 1 and 0. 8 mg/kg, respectively). Lakes in the central and eastern cities where pavement was sampled have bottom sediments with higher PAH concentrations than do those in the western cities relative to degree of urbanization. Bottom-sediment PAH assemblages are similar to those of sealcoated pavement dust regionally, implicating coal-tar-based sealcoat as a PAH source to the central and eastern lakes. Concentrations of benzo[a]pyrene in dust from coal-tar sealcoated pavement and adjacent soils greatly exceed generic soil screening levels, suggesting that research on human-health risk is warranted.

Understanding the fate and transport of petroleum hydrocarbons from coal tar within gasholders.

Science.gov (United States)

Coulon, Frédéric; Orsi, Roberto; Turner, Claire; Walton, Chris; Daly, Paddy; Pollard, Simon J T

2009-02-01

Coal tars have been identified as posing a threat to human health due to their toxic, mutagenic and carcinogenic characteristics. Workers involved in former gasholders decommissioning are potentially exposed to relevant concentrations of volatile and semi-volatile hydrocarbons upon opening up derelict tanks and during tar excavation/removal. While information on contaminated sites air-quality and its implications on medium-long term exposure is available, acute exposure issues associated with the execution of critical tasks are less understood. Calculations indicated that the concentration of a given contaminant in the gasholder vapour phase only depends on the coal tar composition, being only barely affected by the presence of water in the gasholder and the tar volume/void space ratio. Fugacity modelling suggested that risk-critical compounds such as benzene, naphthalene and other monocyclic and polycyclic aromatic hydrocarbons may gather in the gasholder air phase at significant concentrations. Gasholder emissions were measured on-site and compared with the workplace exposure limits (WELs) currently in use in UK. While levels for most of the toxic compounds were far lower than WELs, benzene air-concentrations where found to be above the accepted threshold. In addition due to the long exposure periods involved in gasholder decommissioning and the significant contribution given by naphthalene to the total coal tar vapour concentration, the adoption of a WEL for naphthalene may need to be considered to support operators in preventing human health risk at the workplace. The Level I fugacity approach used in this study demonstrated its suitability for applications to sealed environments such as gasholders and its further refining could provide a useful tool for land remediation risk assessors.

Calcipotriol versus coal tar: a prospective randomized study in stable plaque psoriasis

Energy Technology Data Exchange (ETDEWEB)

Sharma, V.; Kaur, I.; Kumar, B. [Postgraduate Institute of Medicinal Education & Research, Chandigarh (India)

2003-10-01

Topical therapies are the first line of treatment for patients with stable plaque psoriasis (SPP) affecting a limited body surface area. Very few trials comparing newer agents, such as 0.005% topical calcipotriol, with conventional modes of therapy, such as coal tar ointment, have been reported. A prospective, right-left randomized, investigator-blinded study with a 12-week treatment period and an 8-week follow-up period was performed. It was found that 0.005% calcipotriol ointment produced a faster initial response and had better cosmetic acceptability in patients, although after a long period of treatment, i.e. 12 weeks, 5% coal tar ointment had comparable efficacy. There was no statistically significant difference in the relapse rates between the two modalities.

Use of advanced chemical fingerprinting in PAH source identification and allocation at a coal tar processing site

International Nuclear Information System (INIS)

Brown, J.S.; Boehm, P.D.; Douglas, G.S.

1995-01-01

Advanced chemical fingerprinting analyses were used to determine source allocation at a former coal tar processing facility which had been converted to a petroleum recycling site. Soil samples from the site had high petroleum hydrocarbon concentrations and elevated levels of polynuclear aromatic hydrocarbons (PAH). Comparisons of PAH distributions were used to differentiate the coal tar hydrocarbons from the petroleum hydrocarbons in soil samples. A more specific technique was needed to accurately allocate the contribution of the two sources to the observed PAH contamination in the soil. Petroleum biomarkers (steranes and triterpanes) which are present in crude oils and many refined petroleum products but are absent in coal tar were used to quantitatively allocate the source of the PAH contamination based on the relative ratio of the PAH to the biomarkers in soil samples. Using the resulting coal tar/petroleum source ratio the contribution of petroleum to the overall PAH contamination at the site was calculated. A multivariate statistical technique (principal component analysis or PCA) was used to provide an independent validation of the source allocation. The results of the source allocation provided a foundation for the site clean-up and remediation costs

Physical properties and component contents of brown coal tars obtained in semicoking with a solid heat transfer semicoke

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, V I; Bobrova, A A

1955-01-01

Tar obtained in low-temperature carbonization of brown coals with brown-coal semicoke as a heat-transfer medium contains more water and dust, has a lower drop point, and a higher specific gravity, and contains more asphaltene and less paraffin than does tar from the same coal produced in rotating retorts or in shaft kilns. The brown-coal semicoke used as a heat-transfer medium produces partial thermal cracking of the fuel and polymerization of the products of secondary decompositions. The yield of asphaltenes is lowered when the carbonization temperature is raised.

Topical coal tar alone and in combination with oral methotrexate in management of psoriasis : a retrospective analysis

Directory of Open Access Journals (Sweden)

Prasad PVS

1997-01-01

Full Text Available Thirty five patients admitted with psoriasis were analysed. 16 patients received 20% crude coal tar and 19 patients received 20% crude coal tar along with methotrexate in a weekly oral schedule (15mg/wk. After 4 weeks of therapy there was total clearence in 52.6% of the patients with combination therapy, whereas only 12.5% of the patients with conventional therapy achieved this.

Ukrainian brown-coal tars recovered at low-temperature carbonization with solid heating medium

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, V I; Govorova, R P; Fadeicheva, A G; Kigel, T B; Chernykh, M K

1955-01-01

Three samples of tar were recovered in the laboratory from brown coals carbonized at 375/sup 0/ to 456/sup 0/ +- 25/sup 0/ in a retort with inner heating by solid circulating medium, namely, semicoke (ratio: 4 or 3:1) first heated to 700/sup 0/. One comparative (parallel) experiment was carried out in a retort with inner heating by inert gases entering the retort at 580/sup 0/ to 600/sup 0/ and leaving it at 115/sup 0/ to 120/sup 0/. The tars that were recovered from the retort with the solid heating medium contained a high percentage of coal dust and moisture, which were separated from the tars in supercentrifuges (15,000 rpm). Four samples of cleaned tars were fractionated in a Cu flask with a 2-ball fractional column. The tars from the retort with the solid-heating medium are characterized by increased yield of the petroleum-ether fraction (16.3 or 19.3%) and decreased yield of the paraffin fraction (15.1 to 21.2%) in comparison with those of tar from the retort with gas heating (5.9% of the petroleum ether fraction and 36.5% of paraffin fraction). The yield of paraffin from the paraffin fraction also decreased from 90.6% to 62.6-74.3%. This result shows that in the first case the carbonized products were cracked to a higher degree than those from the retort with gas heating. In raw phenols recovered from fractions of investigated tars, the yield of the phenol-cresol fraction (182/sup 0/ to 204/sup 0/) decreased from 25.9% to 13.0-18.9%.

Hydroconversion of coal tars: effect of the temperature of pyrolysis on the reactivity of tars

Energy Technology Data Exchange (ETDEWEB)

Lemberton, J.L.; Touzeyidio, M.; Guisnet, M.

1988-12-01

The hydroconversion of a low-temperature and of a high-temperature tar was carried out in the presence of a sulfided Ni and Mo on alumina catalyst - pure or mixed with an acid catalyst (HY zeolite). Significant amounts of light products can be obtained from low temperature tar, formed however through a non-catalytic process. On the contrary, there is a slight catalytic effect during the hydroprocessing of high temperature tar, but the yield in light products is very low. These results can be explained by an extensive poisoning of the NiMo on alumina catalyst by coke which is initiated by the O- and N-containing compounds of the tars. 10 refs., 1 fig., 3 tabs.

PAHs underfoot: contaminated dust from coal-tar sealcoated pavement is widespread in the United States

Energy Technology Data Exchange (ETDEWEB)

Peter C. Van Metre; Barbara J. Mahler; Jennifer T. Wilson [U.S. Geological Survey, Austin, TX (USA)

2009-01-15

We reported in 2005 that runoff from parking lots treated with coal-tar-based sealcoat was a major source of polycyclic aromatic hydrocarbons (PAHs) to streams in Austin, Texas. Here we present new data from nine U.S. cities that show nationwide patterns in concentrations of {Sigma}PAHs associated with sealcoat. Dust was swept from parking lots in six cities in the central and eastern U.S., where coal-tar-based sealcoat dominates use, and three cities in the western U.S., where asphalt-based sealcoat dominates use. For six central and eastern cities, median SPAH concentrations in dust from sealcoated and unsealcoated pavement are 2200 and 27 mg/kg, respectively. For three western cities, median SPAH concentrations in dust from sealcoated and unsealcoated pavement are similar and very low (2.1 and 0.8 mg/kg, respectively). Lakes in the central and eastern cities where pavement was sampled have bottom sediments with higher PAH concentrations than do those in the western cities relative to degree of urbanization. Bottom-sediment PAH assemblages are similar to those of sealcoated pavement dust regionally, implicating coal-tar-based sealcoat as a PAH source to the central and eastern lakes. Concentrations of benzo(a)pyrene in dust from coal-tar sealcoated pavement and adjacent soils greatly exceed generic soil screening levels, suggesting that research on human-health risk is warranted. 30 refs., 4 figs., 2 tabs.

Phase-equilibria for design of coal-gasification processes: dew points of hot gases containing condensible tars. Final report

Energy Technology Data Exchange (ETDEWEB)

Prausnitz, J.M.

1980-05-01

This research is concerned with the fundamental physical chemistry and thermodynamics of condensation of tars (dew points) from the vapor phase at advanced temperatures and pressures. Fundamental quantitative understanding of dew points is important for rational design of heat exchangers to recover sensible heat from hot, tar-containing gases that are produced in coal gasification. This report includes essentially six contributions toward establishing the desired understanding: (1) Characterization of Coal Tars for Dew-Point Calculations; (2) Fugacity Coefficients for Dew-Point Calculations in Coal-Gasification Process Design; (3) Vapor Pressures of High-Molecular-Weight Hydrocarbons; (4) Estimation of Vapor Pressures of High-Boiling Fractions in Liquefied Fossil Fuels Containing Heteroatoms Nitrogen or Sulfur; and (5) Vapor Pressures of Heavy Liquid Hydrocarbons by a Group-Contribution Method.

Gas emissions, minerals, and tars associated with three coal fires, Powder River Basin, USA.

Science.gov (United States)

Engle, Mark A; Radke, Lawrence F; Heffern, Edward L; O'Keefe, Jennifer M K; Hower, James C; Smeltzer, Charles D; Hower, Judith M; Olea, Ricardo A; Eatwell, Robert J; Blake, Donald R; Emsbo-Mattingly, Stephen D; Stout, Scott A; Queen, Gerald; Aggen, Kerry L; Kolker, Allan; Prakash, Anupma; Henke, Kevin R; Stracher, Glenn B; Schroeder, Paul A; Román-Colón, Yomayra; ter Schure, Arnout

2012-03-15

Ground-based surveys of three coal fires and airborne surveys of two of the fires were conducted near Sheridan, Wyoming. The fires occur in natural outcrops and in abandoned mines, all containing Paleocene-age subbituminous coals. Diffuse (carbon dioxide (CO(2)) only) and vent (CO(2), carbon monoxide (CO), methane, hydrogen sulfide (H(2)S), and elemental mercury) emission estimates were made for each of the fires. Additionally, gas samples were collected for volatile organic compound (VOC) analysis and showed a large range in variation between vents. The fires produce locally dangerous levels of CO, CO(2), H(2)S, and benzene, among other gases. At one fire in an abandoned coal mine, trends in gas and tar composition followed a change in topography. Total CO(2) fluxes for the fires from airborne, ground-based, and rate of fire advancement estimates ranged from 0.9 to 780mg/s/m(2) and are comparable to other coal fires worldwide. Samples of tar and coal-fire minerals collected from the mouth of vents provided insight into the behavior and formation of the coal fires. Published by Elsevier B.V.

Coal tar induces AHR-dependent skin barrier repair in atopic dermatitis

NARCIS (Netherlands)

Bogaard, E.H. van den; Bergboer, J.G.M.; Vonk-Bergers, M.; Vlijmen-Willems, I.M. van; Hato, S.V.; Valk, P.G. van der; Schroder, J.M.; Joosten, I.; Zeeuwen, P.L.J.M.; Schalkwijk, J.

2013-01-01

Topical application of coal tar is one of the oldest therapies for atopic dermatitis (AD), a T helper 2 (Th2) lymphocyte-mediated skin disease associated with loss-of-function mutations in the skin barrier gene, filaggrin (FLG). Despite its longstanding clinical use and efficacy, the molecular

A source mixing model to apportion PAHs from coal tar and asphalt binders in street pavements and urban aquatic sediments

Energy Technology Data Exchange (ETDEWEB)

Ahrens, M.J.; Depree, C.V. [National Institute of Water & Atmospheric Research, Hamilton (New Zealand)

2010-12-15

Present-day and more than 30 years old road and footpath pavements from Auckland, New Zealand were analysed for PAHs to test the hypothesis that coal tar based pavement binders contribute to unusually high PAH concentrations in adjacent stream and estuarine sediments Total PAH ({Sigma}{sub 28}PAH) concentrations in the dichloromethane-soluble fraction ('binder'), comprising 5-10% of pavement mass, were as high as 200 000 mg kg{sup -1}(10 000 mg kg{sup -1} in binder + aggregate) Older and deeper pavement layers were strongly pyrogenic, whereas pavement layers from recently sealed roads had a more petrogenic composition and more than 1000 times lower Sigma(28)PAH concentrations. Source identification analysis using three PAH isomer ratio pairs (benz(a)anthracene/(benz(a)anthracene + chrysene), benzo(a)pyrene/(benzo(a)pyrene + benzo(e)pyrene)), and indeno(1,2,3-cd)pyrene/(indeno(1,2,3-cd)pyrene + benzo(g,h,i)perylene) revealed low PAH (bitumen) pavements to have consistently lower isomer ratios than high PAH (coal tar) samples. A concentration-weighted mixing model, with coal tar and bitumen as source materials, explained more than 80% of the variance in isomer ratios and enveloped the entire PAH compositional and concentration range encountered PAH composition and concentrations in adjacent stream sediments ({gt} 15 mg kg{sup -1} dry weight) were consistent with diluted coal tar material as a principal PAH source. Due to the very high PAH concentrations of coal tar, a coal tar content of as little as 0.01% of total sediment mass can account for more than 90% of PAH concentrations in adjacent stream sediments.

Dissolution and transport of coal tar compounds in fractured clay-rich residuum

DEFF Research Database (Denmark)

Vulava, Vijay M.; McKay, Larry D.; Broholm, Mette Martina

2012-01-01

the importance of rapid dissolution and transport through the fracture networks. The concentrations continued to rise but did not reach the corresponding effective solubility limit in most cases. Compounds that were less soluble and those that were more susceptible to sorption or matrix diffusion eluted...... at a much slower rate. Analysis of contaminant concentrations in microcore residuum samples indicated that all 10 compounds had spread throughout the entire monolith and had diffused into the fine-grained matrix between fractures. These data suggest that the predominantly fine pore structure did not appear......We investigated the dissolution and transport of organic contaminants from a crude coal tar mixture in a monolith of fractured clay-rich residuum. An electrolyte solution was eluted through the residuum monolith containing a small emplaced source of coal tar under biologically inhibited and mildly...

Technological changes illustrated by the coal tar and tar dye industry; Die Wandlung der Technik am Beispiel der Steinkohlenteer- und Teerfarben-Chemie

Energy Technology Data Exchange (ETDEWEB)

Collin, G. [Deutsche Gesellschaft fuer Chemisches Apparatewesen, Chemische Technik und Biotechnologie e.V. (DECHEMA), Frankfurt am Main (Germany)

2001-05-01

Coal tar was detected in the 17th century in laboratory experiments based on empirical knowledge. In the 18th century industrial revolution, coal tar was an undesired by-product of iron production and coking plants. It was first used in the 19th century for impregnating railway sleepers. Later developments in atomic theory, new chemical symbols and organic element analysis provided the basis for discovering and chemical characterisation of coal tar constituents. Laboratory experiments with these tar constituents resulted in the first synthetic dyes, the postulation of tetravalent carbon and the resulting structural theory in organic chemistry for systematic synthesis of many tar dyes to substitute natural dyes in the textile industry. The technical application of these syntheses was part 2 of the industrial revolution and the foundation of the chemical industry in Germany, which developed rapidly in the 2nd half of the 19th century. Tar dye chemistry has made a significant contribution to Germany's economic growth and the change from an agricultural to an industrialized country. [German] Die Entdeckung des Steinkohlenteers im 17. Jahrhundert basiert auf durch Erfahrungswissen gepraegten Laboratoriumsexperimenten. Im Verlauf der 'Industriellen Revolution' des 18. Jahrhunderts ist der Steinkohlenteer zunaechst ein laestiges Abfallprodukt der Eisengewinnung im Kokshochofen und der Leuchtgasherstellung durch Kohlenverkokung. Erste technische Applikation finden Steinkohlenteeroele im 19. Jahrhundert durch den Eisenbahnbau zur Langzeit-Konservierung der dafuer benoetigten Holzschwellen. Die wissenschaftlichen Erfkenntnisse zur Atomtheorie, eine neue chemische Zeichensprache und die organische Elementaranalyse werden Voraussetzungen zur Entdeckung und chemischen Charakterisierung der Hauptinhaltsstoffe des Steinkohlenteers. Laboratoriumsexperimente mit den entdeckten Teerinhaltsstoffen fuehren zur Erfindung der ersten synthetischen Farbstoffe, die

Cancer risk from incidental ingestion exposures to PAHs associated with coal-tar-sealed pavement

Science.gov (United States)

Williams, E. Spencer; Mahler, Barbara J.; Van Metre, Peter C.

2012-01-01

Recent (2009-10) studies documented significantly higher concentrations of polycyclic aromatic hydrocarbons (PAHs) in settled house dust in living spaces and soil adjacent to parking lots sealed with coal-tar-based products. To date, no studies have examined the potential human health effects of PAHs from these products in dust and soil. Here we present the results of an analysis of potential cancer risk associated with incidental ingestion exposures to PAHs in settings near coal-tar-sealed pavement. Exposures to benzo[a]pyrene equivalents were characterized across five scenarios. The central tendency estimate of excess cancer risk resulting from lifetime exposures to soil and dust from nondietary ingestion in these settings exceeded 1 × 10–4, as determined using deterministic and probabilistic methods. Soil was the primary driver of risk, but according to probabilistic calculations, reasonable maximum exposure to affected house dust in the first 6 years of life was sufficient to generate an estimated excess lifetime cancer risk of 6 × 10–5. Our results indicate that the presence of coal-tar-based pavement sealants is associated with significant increases in estimated excess lifetime cancer risk for nearby residents. Much of this calculated excess risk arises from exposures to PAHs in early childhood (i.e., 0–6 years of age).

BTX production by in-situ contact reforming of low-temperature tar from coal with zeolite-derived catalysts; Zeolite kei shokubai wo mochiita sekitan teion tar no sesshoku kaishitsu ni yoru BTX no seisei

Energy Technology Data Exchange (ETDEWEB)

Matsunaga, T.; Fuda, K.; Murakami, K.; Kyo, M.; Hosoya, S.; Kobayashi, S. [Akita University, Akita (Japan). Mining College

1996-10-28

On BTX production process from low-temperature tar obtained by pyrolysis of coal, the effect of exchanged metallic species and reaction temperature were studied using metallic ion-exchanged Y-zeolite as catalyst. In experiment, three kinds of coals with different produced tar structures such as Taiheiyo and PSOC-830 sub-bituminous coals and Loy Yang brown coal were used. Y-zeolite ion-exchanged with metal chloride aqueous solution was used as catalyst. Zn{sup 2+}, Ni{sup 2+} and In{sup 3+} were used as metal ions to be exchanged. The experiment was conducted by heating a pyrolysis section up to 600{degree}C for one hour after preheating a contact reforming section up to a certain proper temperature. As a result, the Ni system catalyst was effective for BTX production from aromatic-abundant tar, while the Zn system one from lower aromatic tar. In general, relatively high yields of toluene and xylene were obtained at lower temperature, while those of benzene at higher temperature. 4 figs., 1 tab.

Copyrolysis of coal with coke-oven gas. III. Analysis of tar

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

1998-02-01

Tars from copyrolysis of Xianfeng lignite with coke-oven gas (COG) at different pressures (0.1-5 MPa) and heating rates (5-25{degree}C/min) to a final temperature of 650{degree}C were analyzed and compared with hydropyrolysis under the same H{sub 2} partial pressure. The results indicated that high contents of BTX, PCX and naphthalene were found in the tar from copyrolysis of Xianfeng lignite with COG. Pressure and heating rate have important effects on tar yields and the contents of BTX, PCX and naphthalene in oil. Increasing pressure and decreasing heating rate enhance the tar yields and result in high yields of BTX and PCX. When compared with hydropyrolysis under the same H{sub 2} partial pressure, the tar yield increases by 1.2 times and the yields of BTX, PCX and naphthalene by about 1.6, 1.3 and 1.6 times, respectively. At the same total pressure (3MPa), the yields of BTX and naphthalene from copyrolysis are equal to those from hydropyrolysis. The results reveal that other components in COG, such as methane, carbon monoxide etc., are of importance for pyrolysis behaviour of coal under COG and improvement of oil qualities. 5 refs., 5 figs., 2 tabs.

Polycyclic aromatic hydrocarbons (PAHs) in a coal tar standard reference material - SRM 1597a updated

Energy Technology Data Exchange (ETDEWEB)

Wise, Stephen A.; Poster, Dianne L.; Rimmer, Catherine A.; Schubert, Patricia; Sander, Lane C.; Schantz, Michele M. [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); Leigh, Stefan D. [National Institute of Standards and Technology (NIST), Statistical Engineering Division, Gaithersburg, MD (United States); Moessner, Stephanie [National Institute of Standards and Technology (NIST), Analytical Chemistry Division, Gaithersburg, MD (United States); GMP/Comparator Labs, Werthenstein Chemie AG, Industrie Nord, Schachen (Switzerland)

2010-09-15

SRM 1597 Complex Mixture of Polycyclic Aromatic Hydrocarbons from Coal Tar, originally issued in 1987, was recently reanalyzed and reissued as SRM 1597a with 34 certified, 46 reference, and 12 information concentrations (as mass fractions) for polycyclic aromatic hydrocarbons (PAHs) and polycyclic aromatic sulfur heterocycles (PASHs) including methyl-substituted PAHs and PASHs. The certified and reference concentrations (as mass fractions) were based on results of analyses of the coal tar material using multiple analytical techniques including gas chromatography/mass spectrometry on four different stationary phases and reversed-phase liquid chromatography. SRM 1597a is currently the most extensively characterized SRM for PAHs and PASHs. (orig.)

Composition of phenols in the primary tar of bituminous brown coal of the Ukrainian S. S. R

Energy Technology Data Exchange (ETDEWEB)

Karavaev, N M; Fadeicheva, A G; Kuznetsov, V I

1957-01-01

The phenol content in the low-temperature carbonizatin tar of brown coal is higher than in high-temperature coking tar, and the tar obtained in the carbonization of briquets in the Pintsch ovens was investigated after its separation at the carbonization plant. The phenol-containing fraction was extracted with 13 percent NaOH. The phenols were fractionated into narrow fractions at 8- to 9-millimeter pressure, and the fractions were identified by their melting point, n, OH content, analysis, and the melting point of their arylglycolic acids. Lower phenols (44 percent) wre found in the crude-phenol fraction, including 6 percent of crystalline PhOH, melting point 34/sup 0/; o-C/sub 6/H/sub 4/(Me)OH, melting point 27/sup 0/; 9.25 percent m- and o-cresols, with 32 percent m-cresol in the mixture EtC/sub 6/H/sub 4/OH formed 4.5 percent of the crude phenols, and consisted of o-, m-, and p-ethylphenols, 1,4,2-, 1,3,4-, 1,3,5-, and 1,2,4-xylenols.

Mass Transfer Coefficientin Stirred Tank for p -Cresol Extraction Process from Coal Tar

International Nuclear Information System (INIS)

Fardhyanti, D S; Tyaningsih, D S; Afifah, S N

2017-01-01

Indonesia is a country that has a lot of coal resources. The Indonesian coal has a low caloric value. Pyrolysis is one of the process to increase the caloric value. One of the by-product of the pyrolysis process is coal tar. It contains a lot of aliphatic or aromatic compounds such as p -cresol (11% v/v). It is widely used as a disinfectant. Extractionof p -Cresol increases the economic value of waste of coal. The aim of this research isto study about mass tranfer coefficient in the baffled stirred tank for p -Cresolextraction from coal tar. Mass transfer coefficient is useful for design and scale up of industrial equipment. Extraction is conducted in the baffled stirred tank equipped with a four-bladed axial impeller placed vertically in the vessel. Sample for each time processing (5, 10, 15, 20, 25 and 30minutes) was poured into a separating funnel, settled for an hour and separated into two phases. Then the two phases were weighed. The extract phases and raffinate phases were analyzed by Spectronic UV-Vis. The result showed that mixing speed of p -Cresol extraction increasesthe yield of p -Cresol and the mass transfer coefficient. The highest yield of p -Cresol is 49.32% and the highest mass transfer coefficient is 4.757 x 10 -6 kg/m 2 s. (paper)

Mass Transfer Coefficientin Stirred Tank for p-Cresol Extraction Process from Coal Tar

Science.gov (United States)

Fardhyanti, D. S.; Tyaningsih, D. S.; Afifah, S. N.

2017-04-01

Indonesia is a country that has a lot of coal resources. The Indonesian coal has a low caloric value. Pyrolysis is one of the process to increase the caloric value. One of the by-product of the pyrolysis process is coal tar. It contains a lot of aliphatic or aromatic compounds such asp-cresol (11% v/v). It is widely used as a disinfectant. Extractionof p-Cresol increases the economic value of waste of coal. The aim of this research isto study about mass tranfer coefficient in the baffled stirred tank for p-Cresolextraction from coal tar. Mass transfer coefficient is useful for design and scale up of industrial equipment. Extraction is conducted inthe baffled stirred tank equipped with a four-bladed axial impeller placed vertically in the vessel. Sample for each time processing (5, 10, 15, 20, 25 and 30minutes) was poured into a separating funnel, settled for an hour and separated into two phases. Then the two phases were weighed. The extract phases and raffinate phases were analyzed by Spectronic UV-Vis. The result showed that mixing speed of p-Cresol extraction increasesthe yield of p-Cresol and the mass transfer coefficient. The highest yield of p-Cresol is 49.32% and the highest mass transfer coefficient is 4.757 x 10-6kg/m2s.

Epoxy-borax-coal tar composition for a radiation protective, burn resistant drum liner and centrifugal casting method

International Nuclear Information System (INIS)

Boyer, N.W.; Taylor, R.S.

1980-01-01

A boron containing burn resistant, low level radiation protection material useful, for example, as a liner for radioactive waste disposal and storage, a component for neutron absorber, and a shield for a neutron source. The material is basically composed of borax in the range of 25-50%, coal tar in the range of 25-37.5%, with the remainder being an epoxy resin mix. A preferred composition is 50% borax, 25% coal tar and 25% epoxy resin. The material is not susceptible to burning and is about 1/5 the cost of existing radiation protection material utilized in similar applications

The migration and monitoring of viscous NAPLs (coal tar and creosote) in the subsurface

Energy Technology Data Exchange (ETDEWEB)

Jackson, R. [Intera Engineering Ltd., Heidelberg, ON (Canada)

2009-07-01

The high viscosity of nonaqueous phase liquids (NAPLs) such as creosote and coal tar complicates efforts to monitor their mobility at contaminated sites. Viscous NAPLs can remain mobile for many decades after their application as a wood preservative, or after the closure of the facilities in which they were generated. NAPL-wet pathways in the subsurface can also lead to errors in residual saturation measurements. This abstract discussed issues related to creeping flow and the low seepage rates that are not accounted for using traditional measuring methods. Examples of creeping flow and the monitoring techniques used to assess it were presented for sites in British Columbia and Florida. The drainage of viscous NAPLs during water table declines was also considered, and a case study of a coal tar-removal procedures using polymer surfactant flooding was presented.

Coal-tar-based sealcoated pavement: a major PAH source to urban stream sediments.

Science.gov (United States)

Witter, Amy E; Nguyen, Minh H; Baidar, Sunil; Sak, Peter B

2014-02-01

We used land-use analysis, PAH concentrations and assemblages, and multivariate statistics to identify sediment PAH sources in a small (~1303 km(2)) urbanizing watershed located in South-Central, Pennsylvania, USA. A geographic information system (GIS) was employed to quantify land-use features that may serve as PAH sources. Urban PAH concentrations were three times higher than rural levels, and were significantly and highly correlated with combined residential/commercial/industrial land use. Principal components analysis (PCA) was used to group sediments with similar PAH assemblages, and correlation analysis compared PAH sediment assemblages to common PAH sources. The strongest correlations were observed between rural sediments (n = 7) and coke-oven emissions sources (r = 0.69-0.78, n = 5), and between urban sediments (n = 22) and coal-tar-based sealcoat dust (r = 0.94, n = 47) suggesting that coal-tar-based sealcoat is an important urban PAH source in this watershed linked to residential and commercial/industrial land use. Copyright © 2013 Elsevier Ltd. All rights reserved.

Topical tar: Back to the future

Energy Technology Data Exchange (ETDEWEB)

Paghdal, K.V.; Schwartz, R.A. [University of Medicine & Dentistry of New Jersey, Newark, NJ (United States)

2009-08-15

The use of medicinal tar for dermatologic disorders dates back to the ancient times. Although coal tar is utilized more frequently in modern dermatology, wood tars have also been widely employed. Tar is used mainly in the treatment of chronic stable plaque psoriasis, scalp psoriasis, atopic dermatitis, and seborrheic dermatitis, either alone or in combination therapy with other medications, phototherapy, or both. Many modifications have been made to tar preparations to increase their acceptability, as some dislike its odor, messy application, and staining of clothing. One should consider a tried and true treatment with tar that has led to clearing of lesions and prolonged remission times. Occupational studies have demonstrated the carcinogenicity of tar; however, epidemiologic studies do not confirm similar outcomes when used topically. This article will review the pharmacology, formulations, efficacy, and adverse effects of crude coal tar and other tars in the treatment of selected dermatologic conditions.

The pentane- and toluene-soluble fractions of a petroleum residue and three coal tars by size exclusion chromatography and UV-fluorescence spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Karaca, F.; Millan-Agorio, M.; Morgan, T.J.; Bull, I.D.; Herod, A.A.; Kandiyoti, R. [University of London Imperial College Science Technology & Medicine, London (United Kingdom). Dept. of Chemical Engineering

2008-01-15

A petroleum atmospheric pressure distillate residue and three tars derived from different coals using different severities of thermal treatment were separated into seven fractions using column chromatography on silica and sequential elution by the solvent sequence pentane, toluene, acetonitrile, pyridine, 1-methyl-2-pyrrolidinone (NMP) and water. The fractions from the four extractions have been compared using size exclusion chromatography (SEC) in NMP as eluent and by synchronous ultra-violet-fluorescence (UV-F). This paper concerns the pentane and toluene soluble fractions only since these are the least polar fractions. By SEC, the size of the aromatic molecules increased from the first pentane soluble fractions to the toluene-soluble fractions, with the petroleum residue fractions of larger size than the equivalent fractions from coal liquids. The three coal tars showed significant differences, indicating that temperature of pyrolysis had a significant effect on the molecular size. Synchronous UV-F spectra of the four sets of fractions, in solution in NMP, again showed significant differences between the petroleum residue and the coal tars, as well as amongst the three coal tars. In general, the petroleum residue fractions contained smaller aromatic clusters than the coal liquid fractions. These low-polarity fractions contained material excluded from the column porosity in SEC that was unlikely to consist of aggregates of polar molecules.

Coal-tar-based pavement sealcoat, polycyclic aromatic Hydrocarbons (PAHs), and environmental health

Science.gov (United States)

Mahler, B.J.; Van Metre, P.C.

2011-01-01

Studies by the U.S. Geological Survey (USGS) have identified coal-tar-based sealcoat-the black, viscous liquid sprayed or painted on asphalt pavement such as parking lots-as a major source of polycyclic aromatic hydrocarbon (PAH) contamination in urban areas for large parts of the Nation. Several PAHs are suspected human carcinogens and are toxic to aquatic life.

Acid Tar Lagoons: Management and Recovery

Science.gov (United States)

Bohers, Anna; Hroncová, Emília; Ladomerský, Juraj

2017-04-01

This contribution presents the issue with possibility of definitive removal of dangerous environmental burden in Slovakia - serious historical problem of two acid tar lagoons. In relation to their removal, no technology has been found so far - technologically and economically suitable, what caused problems with its management. Locality Predajná is well known in Slovakia by its character of contrasts: it is situated in the picturesque landscape of National Park buffer zone of Nízke Tatry, on the other site it is contaminated by 229 211m3 of acid tar with its characteristics of toxicity, carcinogenicity, teratogenicity, mutagenicity and toxicity especially for animals and plants. Acid tar in two landfills with depth of 1m in case of the first lagoon and 9,5m in case of the second lagoon is a waste product derived from operation of Petrochema Dubová - refinery and petrochemical plant whose activity was to process the crude oil through processes of sulfonation and adsorption technology for producing lubricating and special oils, synthetic detergents and special white oils for cosmetic and medical purposes. A part of acid tar was incinerated in two incineration plats. Concentration of SO2 in combustion gases was too high and it was not possible to decrease it under the value of 2000 mg.mn-3 [LADOMERSKÝ, J. - SAMEŠOVÁ, D.: Reduction in sulfur dioxide emissions waste gases of incineration plant. Acta facultatis ecologiae. 1999, p. 217-223]. That is why it was necessary to put them out of operation. Later, because of public opposition it was not possible to build a new incineration plat corresponding to the state of the art. Even though actual Slovak and European legislative for protection of environment against such impacts, neither of tried methods - bio or non-biologic treatment methods - was proved as suitable for processing or for recovery in the reason of different factors admission: i.e. strong aggressivity, difficulty with handling because of its sludgy and

Main component analysis of nuclear magnetic resonance /sup 1/H and /sup 13/C quantitative spectra of hydrogenation products of tars from Kansk-Achinsk Achinsk and Cheremkhovsk coals

Energy Technology Data Exchange (ETDEWEB)

Kushnarev, D.F.; Polonov, V.M.; Donskikh, V.I.; Rokhina, E.F.; Kalabin, G.A.

1986-03-01

Possibility is discussed of examining nuclear magnetic resonance /sup 1/H and /sup 13/C quantitative spectra of coal tar hydrogenation products using main component factorial analysis and applying special mathematical methods of processing experimental data. Nuclear magnetic resonance spectra of hydrogenation products of low temperature Cheremkhovsk coal carbonization tar and rapid pyrolysis Kansk-Achinsk coal tar were obtained on a WP-200SY (Bruker) spectrometer at 50.3 and 200.1 MHz, respectively. Data processing was carried out on an ODRA-1304 computer. Comparative correlation of parameters are given of tars and hydrogenation products which consist of hydrogenation of aromatic cycles and destruction of alkyl substituents, and factorial loads on structural parameters of tar hydrogenation products. 11 references.

The effects of topical corticosteroids and a coal tar preparation on dithranol-induced irritation in patients with psoriasis

Energy Technology Data Exchange (ETDEWEB)

Swinkels, O.Q.J.; Kucharekova, M.; Prins, M.; Gerritsen, M.J.P.; van der Valk, P.G.M.; van de Kerkhof, P.C.M. [University of Nijmegen, Nijmegen (Netherlands). Medical Center

2003-02-01

Dithranol has been a mainstay in the treatment of psoriasis for more than 80 years. Although a safe approach, the irritation of the clinically uninvolved perilesional skin remains a major limitation of this treatment. Corticosteroids and coal tar solution have an anti-inflammatory potential. The aim of the present study was to investigate the clinical and cell-biological effects of two topical corticosteroids and a coal tar preparation on dithranol-irritated skin. The expression of epidermal proliferation, differentiation and inflammation markers and the clinical irritation scores indicate that the application of a high potency corticosteroid is the best approach to minimise dithranol irritation.

Biogeochemical gradients above a coal tar DNAPL

Energy Technology Data Exchange (ETDEWEB)

Scherr, Kerstin E., E-mail: kerstin.brandstaetter-scherr@boku.ac.at [University of Natural Resources and Life Sciences Vienna (BOKU), Department IFA-Tulln, Institute for Environmental Biotechnology, Konrad Lorenz Strasse 20, 3430 Tulln (Austria); Backes, Diana [University of Natural Resources and Life Sciences Vienna (BOKU), Department IFA-Tulln, Institute for Environmental Biotechnology, Konrad Lorenz Strasse 20, 3430 Tulln (Austria); Scarlett, Alan G. [University of Plymouth, Petroleum and Environmental Geochemistry Group, Biogeochemistry Research Centre, Drake Circus, Plymouth, Devon PL4 8AA (United Kingdom); Lantschbauer, Wolfgang [Government of Upper Austria, Directorate for Environment and Water Management, Division for Environmental Protection, Kärntner Strasse 10-12, 4021 Linz (Austria); Nahold, Manfred [GUT Gruppe Umwelt und Technik GmbH, Ingenieurbüro für Technischen Umweltschutz, Plesching 15, 4040 Linz (Austria)

2016-09-01

Naturally occurring distribution and attenuation processes can keep hydrocarbon emissions from dense non aqueous phase liquids (DNAPL) into the adjacent groundwater at a minimum. In a historically coal tar DNAPL-impacted site, the de facto absence of a plume sparked investigations regarding the character of natural attenuation and DNAPL resolubilization processes at the site. Steep vertical gradients of polycyclic aromatic hydrocarbons, microbial community composition, secondary water quality and redox-parameters were found to occur between the DNAPL-proximal and shallow waters. While methanogenic and mixed-electron acceptor conditions prevailed close to the DNAPL, aerobic conditions and very low dissolved contaminant concentrations were identified in three meters vertical distance from the phase. Comprehensive two-dimensional gas chromatography–mass spectrometry (GC × GC–MS) proved to be an efficient tool to characterize the behavior of the present complex contaminant mixture. Medium to low bioavailability of ferric iron and manganese oxides of aquifer samples was detected via incubation with Shewanella alga and evidence for iron and manganese reduction was collected. In contrast, 16S rDNA phylogenetic analysis revealed the absence of common iron reducing bacteria. Aerobic hydrocarbon degraders were abundant in shallow horizons, while nitrate reducers were dominating in deeper aquifer regions, in addition to a low relative abundance of methanogenic archaea. Partial Least Squares – Canonical Correspondence Analysis (PLS-CCA) suggested that nitrate and oxygen concentrations had the greatest impact on aquifer community structure in on- and offsite wells, which had a similarly high biodiversity (H’ and Chao1). Overall, slow hydrocarbon dissolution from the DNAPL appears to dominate natural attenuation processes. This site may serve as a model for developing legal and technical strategies for the treatment of DNAPL-impacted sites where contaminant plumes are

You're standing on it! Coal-tar-based pavement sealcoat and environmental and human health

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.

2013-01-01

Coal-tar-based sealcoat—a product marketed to protect and beautify asphalt pavement—is a potent source of polycyclic aromatic hydrocarbons (PAHs) to air, soils, streams and lakes, and homes. Does its use present a risk to human health?

Protection Performance Simulation of Coal Tar-Coated Pipes Buried in a Domestic Nuclear Power Plant Using Cathodic Protection and FEM Method

Energy Technology Data Exchange (ETDEWEB)

Chang, H. Y.; Lim, B. T.; Kim, K. S.; Kim, J. W.; Park, H. B. [KEPCO Engineering and Construction Company, Gimcheon (Korea, Republic of); Kim, Y. S.; Kim, K. T. [Andong National University, Andong (Korea, Republic of)

2017-06-15

Coal tar-coated pipes buried in a domestic nuclear power plant have operated under the cathodic protection. This work conducted the simulation of the coating performance of these pipes using a FEM method. The pipes, being ductile cast iron have been suffered under considerably high cathodic protection condition beyond the appropriate condition. However, cathodic potential measured at the site revealed non-protected status. Converting from 3D CAD data of the power plant to appropriate type for a FEM simulation was conducted and cathodic potential under the applied voltage and current was calculated using primary and secondary current distribution and physical conditions. FEM simulation for coal tar-coated pipe without defects revealed over-protection condition if the pipes were well-coated. However, the simulation for coal tar-coated pipes with many defects predict that the coated pipes may be severely degraded. Therefore, for high risk pipes, direct examination and repair or renewal of pipes are strongly recommended.

Mechanical characterization of Portland cement mortars containing petroleum or coal tar

Directory of Open Access Journals (Sweden)

Garcés, P.

2007-08-01

Full Text Available This article discusses experimental data on the flexural and compressive strength of Portland cement mortars containing additions or cement replacements consisting in petroleum or coal tar, by-products of the oil and coal industries. The materials studied were two coal (BACA and BACB and two petroleum (BPP and BPT tars. The results show that it is feasible to use such materials as a partial replacement for cement in mortar manufacture. This should lead to the design of a new sustainable product that will contribute to lowering the environmental impact of construction materials while at the same time opening up an avenue for the re-use of this type of industrial by-products.En este artículo se presentan datos experimentales de resistencia a flexión y a compresión de morteros de cemento Portland con adición y sustitución de breas de petróleo y de alquitrán de carbón, que son subproductos de la industria del carbón o del petróleo. Los materiales estudiados son breas de alquitrán de carbón A (BACA y B (BACB, y dos breas de petróleo (BPP y (BPT. Los datos demuestran la viabilidad del uso de estas breas en la fabricación de morteros con menores contenidos de cemento, permitiendo diseñar un nuevo material sostenible con el medio ambiente y que contribuya a reducir el impacto ambiental de los materiales de construcción, hecho que permite abrir una nueva vía de valorización de estos subproductos.

Extraction of tar acids with methanol from low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Funasaka, W; Yokogawa, C; Suga, S

1948-01-01

From 20 grams crude middle oil, boiling at 200/sup 0/ to 250/sup 0/, acid content 40%, tar acids were extracted at 20/sup 0/ to 30/sup 0/ with MeOH for comparison with EtOH, NMe/sub 3/, and ethylene glycol. When 80% MeOH is used, the oil extracted amounts to 61%, including 9% acids, if the ratio of crude oil and solvent is kept at 1:2. EtOH is inferior to MeOH. The properties of the crude oil and the purified oil extracted with 80% MeOH are described.

Effect of the rate of heating on the quality of the primary tar in low-temperature coal-carbonization process

Energy Technology Data Exchange (ETDEWEB)

Turskii, Y I

1956-01-01

Two stages are observed. The first stage yields products of the primary and partial decomposition of coal, mainly water, CO/sub 2/, and CO as decomposition products of functional groups (-COOH, > CO, - OH, and so forth). No tar is formed in this stage. The structural decomposition and tar formation occur in the second stage. The rate of heating is important for the quality of the tar obtained. The slow rate of heating with both stages following each other yields a good-quality tar, richer in C and H, with lower O content. In case of high rate of heating both stages overlap. The tar is of poorer quality with higher specific gravity, and contains more O and asphaltenes. The complete experimental data are given in detail.

Aromatic oxygen compounds boiling from 180/sup 0/ to 225/sup 0/ from acid oils in low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Jaeger, A; Kattwinkel, G

1950-01-01

To determine the composition of the Krupp-Lurgi low-temperature coal tar and to develop methods for isolating the various compounds, a quantitative investigation was made of the dry tar acid mixture. The aromatic O compounds boiling up to 225/sup 0/ were secured by fractionation with one of the several columns that are described. Large volumes of tar were fractionated under vacuum in an apparatus with a 10-liter flask, electrically heated, and provided with a fractionating column (packed) with a jacket supplied by recirculated oil, externally heated. Large volumes were fractionated to give sufficient quantities of the O compounds. The method of fractional extraction, not described herein, made the separation of the acid oils by fractional distillation much easier. The aromatic O compounds present in greatest proportion are relatively easily isolated; those present in small quantities and more difficult to separate can be removed as a mixture, which can be hydrogenated directly to solvents. Phenols and cresols are formed in about equal fractions in low-temperature carbonization. Of the various xylenols, the sym-xylenol is present to the greatest extent. O compounds with longer side chains than C/sub 2/ were present only to a very slight extent. At the temperature of formation of these tars, side chains of three or more C atoms formed closed ring compounds (indan derivatives, etc.). Little change appears to occur up to 225/sup 0/ in the fractionation of these acid oils.

Low-temperature tar and oil: properties and applications

Energy Technology Data Exchange (ETDEWEB)

Heinze, R

1942-01-01

In Germany the value of low-temperature tar is largely dependent on its fuel fractions; these vary with the coal and the method of carbonization (external heating or recirculated gases). Brown-coal tars can be processed by distillation, cracking under pressure, hydrogenation under pressure (largest volume of tar is processed by this method) and by solvent extraction, with EtOH, SO/sub 2/, or phenol. Each of these processes is discussed in detail. In the pressure-hydrogenation process, 1.25 kilogram of brown-coal tar yields approximately 1 kilogram of gasoline with an octane number of 60 to 70. Low-temperature tars from bituminous coals can be hydrogenated readily but are not well adapted to solvent extraction. Attempts should be made to produce tar approximating the desired characteristics for fuel directly from the carbonizing apparatus. For laboratory carbonization tests, an approximation to results secured by externally heated retorts is secured by using an insert consisting of a series of perforated trays in the 200-gram Fischer aluminum retort; this reduces the capacity to 100 gram. Fractional condensation is used to separate heavy oil, middle oil, and liquor; low-boiling products are condensed at -20/sup 0/ by solid CO/sub 2/.

Dual vapor extraction on acidic sludge tar at a former refinery

International Nuclear Information System (INIS)

Lear, P.R.; Beall, P.; Townsend, S.

1996-01-01

OHM Remediation Services Corp conducted a pilot-scale demonstration for a novel application of dual vapor extraction technology for the pretreatment of the acid tar sludge material. The acid tar sludge comprised of approximately 60% asphaltene hydrocarbon material, 20% clay, and up to 20% sulfuric acid (H 2 SO 4 ). The liquid layer in the bottom of the pits has a low pH ( 2 ) gas which is released with the sludge material is excavated or handled. The objective of the dual vapor extraction was to remove the SO 2 vapors and liquid layer containing sulfuric acid prior to any further treatment. The dual vapor extraction would reduce the amount of alkaline reagent required for neutralization while eliminating the health and safety concerns. Overall, the DVE pilot demonstration successfully showed that both liquids and vapors could be removed from the acid tar sludge material. The liquid present in the lower portions of the pits will have pH values of 1.0 or less and acidities on the order of 5% H 2 SO 4 . The liquid removed from the acid tar sludge material by a DVE system will have slightly higher pH (∼1.5) and lower alkalinities (∼3% H 2 SO 4 ). The SO 2 concentration in the vapors removed by the DVE system will be variable with initial levels approaching 1,200 ppmv SO 2 . The SO 2 concentration in the vapor phase should decrease with time. A caustic scrubber solution will remove any SO 2 from the vapor phase. After DVE treatment, the acid tar sludge material would have a slightly increased pH and a decreased SO 2 concentration

Preliminary evaluation of ground-water contamination by coal-tar derivatives, St. Louis Park area, Minnesota

Science.gov (United States)

Hult, Marc F.; Schoenberg, Michael E.

1984-01-01

Operation of a coal-tar distillation and wood-preserving plant from 1918 to 1972 in St. Louis Park, a suburb of Minneapolis, Minn., resulted in ground-water contamination. This preliminary evaluation presents an overview of the problem based on the results of the first year (1979) of an ongoing study.

Structure and Mechanism of Staphylococcus aureus TarS, the Wall Teichoic Acid β-glycosyltransferase Involved in Methicillin Resistance.

Directory of Open Access Journals (Sweden)

Solmaz Sobhanifar

2016-12-01

Full Text Available In recent years, there has been a growing interest in teichoic acids as targets for antibiotic drug design against major clinical pathogens such as Staphylococcus aureus, reflecting the disquieting increase in antibiotic resistance and the historical success of bacterial cell wall components as drug targets. It is now becoming clear that β-O-GlcNAcylation of S. aureus wall teichoic acids plays a major role in both pathogenicity and antibiotic resistance. Here we present the first structure of S. aureus TarS, the enzyme responsible for polyribitol phosphate β-O-GlcNAcylation. Using a divide and conquer strategy, we obtained crystal structures of various TarS constructs, mapping high resolution overlapping N-terminal and C-terminal structures onto a lower resolution full-length structure that resulted in a high resolution view of the entire enzyme. Using the N-terminal structure that encapsulates the catalytic domain, we furthermore captured several snapshots of TarS, including the native structure, the UDP-GlcNAc donor complex, and the UDP product complex. These structures along with structure-guided mutants allowed us to elucidate various catalytic features and identify key active site residues and catalytic loop rearrangements that provide a valuable platform for anti-MRSA drug design. We furthermore observed for the first time the presence of a trimerization domain composed of stacked carbohydrate binding modules, commonly observed in starch active enzymes, but adapted here for a poly sugar-phosphate glycosyltransferase.

Separating cresote from tars, mineral oils, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1921-01-07

Phenolic bodies are extracted from tars such as lignite, shale, peat, coal, producer and low temperature tars, and from tar distillates and residues and from mineral oils and distillates by washing with a mixture of acetone and water. Acetone extracts of the tars etc., may be mixed with water or aqueous acetone to cause the separation of the oils, while the creosote remains in solution.

Preparation of pure phenols from tars

Energy Technology Data Exchange (ETDEWEB)

Meyer, J

1933-02-07

A process is disclosed for the preparation of pure phenols from brown coal tar, shale tar, or primary tar, characterized in that the raw oil obtained from the tar is carefully fractionated, in a suitable way without or with a slight pressure decrease, or before the fractionation the raw oil is heated to free the prepared phenolate solution from impurities after successful oxidation by passing in steam at a temperature between 100 and 120/sup 0/C.

PAH concentrations in lake sediment decline following ban on coal-tar-based pavement sealants in Austin, Texas

Science.gov (United States)

Van Metre, Peter C.; Mahler, Barbara J.

2013-01-01

Recent studies have concluded that coal-tar-based pavement sealants are a major source of polycyclic aromatic hydrocarbons (PAHs) in urban settings in large parts of the United States. In 2006, Austin, TX, became the first jurisdiction in the U.S. to ban the use of coal-tar sealants. We evaluated the effect of Austin’s ban by analyzing PAHs in sediment cores and bottom-sediment samples collected in 1998, 2000, 2001, 2012, and 2014 from Lady Bird Lake, the principal receiving water body for Austin urban runoff. The sum concentration of the 16 EPA Priority Pollutant PAHs (∑PAH16) in dated core intervals and surficial bottom-sediment samples collected from sites in the lower lake declined about 44% from 1998–2005 to 2006–2014 (means of 7980 and 4500 μg kg–1, respectively), and by 2012–2014, the decline was about 58% (mean of 3320 μg kg–1). Concentrations of ∑PAH16 in bottom sediment from two of three mid-lake sites decreased by about 71 and 35% from 2001 to 2014. Concentrations at a third site increased by about 14% from 2001 to 2014. The decreases since 2006 reverse a 40-year (1959–1998) upward trend. Despite declines in PAH concentrations, PAH profiles and source-receptor modeling results indicate that coal-tar sealants remain the largest PAH source to the lake, implying that PAH concentrations likely will continue to decline as stocks of previously applied sealant gradually become depleted.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement.

Science.gov (United States)

Mahler, Barbara J; Van Metre, Peter C; Foreman, William T

2014-05-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement. Published by Elsevier Ltd.

Concentrations of polycyclic aromatic hydrocarbons (PAHs) and azaarenes in runoff from coal-tar- and asphalt-sealcoated pavement

Science.gov (United States)

Mahler, Barbara J.; Van Metre, Peter C.; Foreman, William T.

2014-01-01

Coal-tar-based sealcoat, used extensively on parking lots and driveways in North America, is a potent source of PAHs. We investigated how concentrations and assemblages of PAHs and azaarenes in runoff from pavement newly sealed with coal-tar-based (CT) or asphalt-based (AS) sealcoat changed over time. Samples of simulated runoff were collected from pavement 5 h to 111 d following application of AS or CT sealcoat. Concentrations of the sum of 16 PAHs (median concentrations of 328 and 35 μg/L for CT and AS runoff, respectively) in runoff varied relatively little, but rapid decreases in concentrations of azaarenes and low molecular weight PAHs were offset by increases in high molecular weight PAHs. The results demonstrate that runoff from CT-sealcoated pavement, in particular, continues to contain elevated concentrations of PAHs long after a 24-h curing time, with implications for the fate, transport, and ecotoxicological effects of contaminants in runoff from CT-sealcoated pavement.

Composition and Dissolution of a Migratory, Weathered Coal Tar Creosote DNAPL

Directory of Open Access Journals (Sweden)

Kerstin E. Scherr

2016-09-01

Full Text Available Opaque, viscous tars derived from the carbonization of fossile carbon feedstocks, such coal tars and creosote, are long-term sources of groundwater contamination, predominantly with poly- and heterocyclic aromatic hydrocarbons (PAH. The dissolution, ageing and migratory behavior of dense, non aqueous phase liquid (DNAPL coal tar blobs and pools forming at the aquitard is not sufficiently understood to estimate the risk and adequately design groundwater treatment measures at a contaminated site. In this study, we investigate the composition and dissolution of a migrated, aged creosote DNAPL and corresponding experimental and groundwater profiles using comprehensive two-dimensional gas chromatography (GCxGC-MS. GC-FID unresolved compounds were attributed to methylated homocyclic species using GCxGC-MS in the Methylanthracene weight range. Equilibrium concentrations were estimated using Raoult’s law, assuming non-ideal behavior. Low molecular weight compounds were found to be prevalent even after decades of weathering, with Naphthalene (8% by mass representing the most abundant identified compound, contrary to the expected preferential depletion of hydrophilic compounds. Morevoer, dimethylnaphthalenes were relatively more abundant in the aqueous boundary layer than in the DNAPL. DNAPL migration over 400m with the groundwater flow effected lower viscosity and specific gravity of the migrated phase body in a superposition of weathering, transport and aquifer chromatography effects. Based on a decomposition of analysed and estimated constituents using the group contribution approach, reference DNAPL values for activity coefficients γi were used to model aqueous solubilities for selected compounds. Anthracene was close to its theoretical precipitation limit in the bulk DNAPL. While laboratory and modelled DNAPL dissolution behavior agree well, field data imply the presence of specific interfacial in situ processes significantly impacting dissolution

Utilisation of the binders prepared from coal tar pitch and phenolic resins for the production metallurgical quality briquettes from coke breeze and the study of their high temperature carbonization behaviour

Energy Technology Data Exchange (ETDEWEB)

Benk, Ayse [University of Erciyes, Faculty of Art and Science, Department of Chemistry, 38039, Kayseri (Turkey)

2010-09-15

To reduce the cost of the formed coke briquettes which can be used as a substitute fuel to the metallurgical coke for the blast furnace from the coke breeze alternative binders and their blends were used. The high temperature behavior was investigated. The binders tested were: the nitrogen blown, air blown coal tar pitch and the blend of air blown coal tar pitch with the phenolic resins blends. The phenolic resin blends were prepared by mixing equal amount of resole and novalac. From the results, nitrogen blowing resulted in the weakest briquettes. The air blowing procedure should be preferred in place of nitrogen blowing for this purpose. When the air blown coal tar pitch was used alone as a binder, the briquettes must be cured at 200 C for 2 h, then carbonized at a temperature above 670 C. Since it requires higher temperature at carbonization stage, using air blown coal tar pitch alone as a binder was not economical. Therefore, the briquettes were prepared from the blended binder, containing air blown coal tar pitch and phenolic resins blend. The optimum amount of air blown coal tar pitch was found to be 50% w/w in the blended binder. Curing the briquettes at 200 C for 2 h was found to be sufficient for producing strong briquettes with a tensile strength of 50.45 MN/m{sup 2}. When these cured briquettes were carbonized at temperatures 470 C, 670 C and 950 C, their strength were increasing continuously, reaching to 71.85 MN/m{sup 2} at the carbonization temperature of 950 C. These briquettes can be used as a substitute for the metallurgical coke after curing; the process might not require un-economical high temperature carbonization stage. (author)

Diversity of 16S rRNA and dioxygenase genes detected in coal-tar-contaminated site undergoing active bioremediation

Energy Technology Data Exchange (ETDEWEB)

Kumar, M; Khanna, S [NIIT Univ, Neemrana (India). Dept. of Biotechnology & Bioinformation

2010-04-15

In order to develop effective bioremediation strategies for polyaromatic hydrocarbons (PAHs) degradation, the composition and metabolic potential of microbial communities need to be better understood, especially in highly PAH contaminated sites in which little information on the cultivation-independent communities is available. Coal-tar-contaminated soil was collected, which consisted of 122-122.5 mg g{sup -1} total extractable PAH compounds. Biodegradation studies with this soil indicated the presence of microbial community that is capable of degrading the model PAH compounds viz naphthalene, phenanthrene and pyrene at 50 ppm each. PCR clone libraries were established from the DNA of the coal-tar-contaminated soil, targeting the 16S rRNA to characterize (I) the microbial communities, (ii) partial gene fragment encoding the Rieske iron sulfur center {alpha}-subunit) common to all PAH dioxygenase enzymes and (iii) {beta}-subunit of dioxygenase. Phylotypes related to Proteobacteria ({Alpha}-, {Epsilon}- and Gammaproteobacteria), Acidobacteria, Actinobacteria, Firmicutes, Gemmatimonadetes and Deinococci were detected in 16S rRNA derived clone libraries. Many of the gene fragment sequences of alpha-subunit and beta-subunit of dioxygenase obtained from the respective clone libraries fell into clades that are distinct from the reference dioxygenase gene sequences. Presence of consensus sequence of the Rieske type (2Fe2S) cluster binding site suggested that these gene fragments encode for {alpha}-subunit of dioxygenase gene. Sequencing of the cloned libraries representing {alpha}-subunit gene fragments (Rf1) and beta-subunit of dioxygenase showed the presence of hitherto unidentified dioxygenase in coal-tar-contaminated soil.

The use of coal-tar pitches of very high softening point and low carcinogen content as binders for industrial carbon

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-07-01

It has been demonstrated that the content of known carcinogenic polynuclear aromatic hydrocarbons (PAH) in coal-tar pitches may be reduced to levels which comply with existing and/or proposed environmental legislation, typically by distillation at low pressures, and preferably using a form of thin-film evaporation apparatus. However, the immediate products of such distillations usually have very high softening points, typically above 200{degree}C, and are unsuitable for direct utilization in conventional commercial carbon manufacturing processes as a result of the need for very high mixing temperatures. Advantage has been taken of the of a low-PAH coal-tar pitch, supplied in powder form, which has a softening point above 200{degree}C. Methods were examined which might allow mixing and forming of the hard pitch and a petroleum coke aggregate blend either at room temperature or at conventional processing temperature, and hot-pressuring or sintering procedures in which mixtures of the hard pitch and petroleum coke aggregate were formed at or above the softening temperature of the pitch. All the formed products were baked to give carbons which were evaluated for the major properties of density, electrical resistivity and strength. A comparison was also made between the volatiles evolved during the baking of products made with the low-PAH pitch and those made with a conventional coal-tar binder pitch.

Production and investigation of low-temperature coal tar. [Book in German

Energy Technology Data Exchange (ETDEWEB)

1953-01-01

Research into low-temperature carbonization has recently been stimulated because this process can be applied to coals that are not suitable for treatment by the usual high-temperature method. However, in spite of the value of the coke produced by low-temperature carbonization as a smokeless fuel, this process has not proved economical in Germany. Research has therefore been directed towards a more profitable utilization of the tar, and this government publication reports experiments on its detailed analysis by distillation and other methods. The book also includes descriptions of the various types of plant used for low-temperature carbonization and presents a brief history of the process.

Rebound of a coal tar creosote plume following partial source zone treatment with permanganate.

Science.gov (United States)

Thomson, N R; Fraser, M J; Lamarche, C; Barker, J F; Forsey, S P

2008-11-14

The long-term management of dissolved plumes originating from a coal tar creosote source is a technical challenge. For some sites stabilization of the source may be the best practical solution to decrease the contaminant mass loading to the plume and associated off-site migration. At the bench-scale, the deposition of manganese oxides, a permanganate reaction byproduct, has been shown to cause pore plugging and the formation of a manganese oxide layer adjacent to the non-aqueous phase liquid creosote which reduces post-treatment mass transfer and hence mass loading from the source. The objective of this study was to investigate the potential of partial permanganate treatment to reduce the ability of a coal tar creosote source zone to generate a multi-component plume at the pilot-scale over both the short-term (weeks to months) and the long-term (years) at a site where there is >10 years of comprehensive synoptic plume baseline data available. A series of preliminary bench-scale experiments were conducted to support this pilot-scale investigation. The results from the bench-scale experiments indicated that if sufficient mass removal of the reactive compounds is achieved then the effective solubility, aqueous concentration and rate of mass removal of the more abundant non-reactive coal tar creosote compounds such as biphenyl and dibenzofuran can be increased. Manganese oxide formation and deposition caused an order-of-magnitude decrease in hydraulic conductivity. Approximately 125 kg of permanganate were delivered into the pilot-scale source zone over 35 days, and based on mass balance estimates 35% reduction for all monitored compounds except for biphenyl, dibenzofuran and fluoranthene 150 days after treatment, which is consistent with the bench-scale experimental results. Pre- and post-treatment soil core data indicated a highly variable and random spatial distribution of mass within the source zone and provided no insight into the mass removed of any of the

Co-carcinogenesis: Human Papillomaviruses, Coal Tar Derivatives, and Squamous Cell Cervical Cancer

Directory of Open Access Journals (Sweden)

Harry W. Haverkos

2017-11-01

Full Text Available Cervical cancer (CC is the fourth most common cancers among women worldwide. Human papillomaviruses (HPVs play a major role in the etiology of CC, with several lines of epidemiologic and experimental evidence supporting a role for non-viral (co-carcinogens and host genetic factors in controlling the risk for progression to neoplasia among HPV-infected individuals. The role of co-carcinogens in the development of CC is significant in the developing world where poor sanitation and other socio-economic conditions increase the infectious cancer burden. Here, we discuss how exposure to environmental factors such as coal tar derivatives from cigarette smoking, tar-based sanitary products, and inhaled smoke from biomass-burning stoves, could activate host pathways involved in development of HPV-associated squamous cell cancers in resource-limited settings. Understanding interactions between these pathways with certain oncogenic HPV genotypes may guide implementation of strategies for control and treatment of HPV-associated cancers that develop in populations at high risk of exposure to various co-carcinogens.

Preparation of pure phenols from tars

Energy Technology Data Exchange (ETDEWEB)

Meyer, J

1929-06-18

A process is disclosed for preparing pure phenols from brown coal and shale tar, characterized in that the alkaline extract obtained from the tar is oxidized and concurrently the alkaline solution is separated from the existing impurities by heating with steam at high temperature, which finally reaches at least 150/sup 0/C.

Evaluation of the health risk resulting from exposure to polycyclic aromatic hydrocarbons in coal-tar shampoo

Energy Technology Data Exchange (ETDEWEB)

Mennes, W.C.; Van Veen, M.P.; Kroese, E.D.; Speijers, G.J.A.

1996-10-01

Shampoos may contain as much as 56 mg benzo(a)pyrene (BaP)/kg product. Based on a human dermal uptake study, it is plausible that BaP and other PAHs become systemically available after a single use of coal-tar shampoos. Because several PAHs, among which BaP are considered to be carcinogenic substances, the safety of these products has been questioned. Dermal exposure results in skin tumours, but after inhalatory or oral exposure besides to local tumour formation, systemic tumours are found as well. In this report, an estimate of external dermal exposure to BaP has been generated by application of a mathematical model. This estimate was the starting point in an assessment of the additional risk on local skin tumours after contact with a coal-tar shampoo containing 56 mg BaP/kg product. In this assessment it was assumed that this shampoo was used three times weekly. Four different risk estimates were derived, namely for contact times of 1 or 5 minutes per event and for life-time or 40 years of use. 4 tabs., 3 appendices, 15 refs.

Quantitative determination of acid oils in low-temperature coal tar by means of fractional distillation

Energy Technology Data Exchange (ETDEWEB)

Jaeger, A

1950-01-01

The aromatic hydroxy compounds in low-temperature tar were separated, and 75 compounds in the boiling range 180/sup 0/ to 320/sup 0/ isolated by means of fractional distillation in packed columns of at least 45 theoretical plates. Mixtures not separable by fractionation were separated by means of other physicochemical or chemical methods. Hydroxy compounds with boiling point up to 230/sup 0/C were detemined quantitatively, as were the phenols present in low-temperature carbonization liquors. With the Krupp-Lurgi process of low-temperature carbonization, 1.8% phenol, 1.8% o-cresol, and 3.6% m-p-cresols were formed. The tar contained up to 1.3% 1:3:5-xylenol and up to 0.9% 1:2:4-xylenol. Of the 12.1% v/v of phenol, cresols, and xylenols present in tar, 11.2% were determined quantitatively, and 9 hydroxy compounds were identified in the remaining 0.9%. On the basis of these investigations, a technical plant that permitted the recovery of pure low-temperature tar phenols and the preparation of a number of different phenol resins from the mixtures was erected.

Mineralization of PAHs in coal-tar impacted aquifer sediments and associated microbial community structure investigated with FISH

Energy Technology Data Exchange (ETDEWEB)

Rogers, S W; Ong, S K; Moorman, T B [Iowa State University, Ames, IA (USA)

2007-11-15

The microbial community structure and mineralization of polycyclic aromatic hydrocarbons (PAHs) in a coal-tar contaminated aquifer were investigated spatially using fluorescence in situ hybridization (FISH) and in laboratory-scale incubations of the aquifer sediments. DAPI-detected microbial populations in the contaminated sediments were three orders of magnitude greater than nearby uncontaminated sediments, suggesting growth on coal-tar constituents in situ. Actinobacteria, {beta}- and {gamma}-Proteobacteria, and Flavobacteria dominated the in situ aerobic (> 1 mg l{sup -1} dissolved oxygen) microbial community, whereas sulfate-reducing bacteria comprised 37% of the microbial community in the sulfidogenic region of the aquifer. Rapid mineralization of naphthalene and phenanthrene were observed in aerobic laboratory microcosms and resulted in significant enrichment of {beta}- and {gamma}-Proteobacteria potentially explaining their elevated presence in situ. Nitrate- and sulfate-limited mineralization of naphthalene in laboratory microcosms occurred to a small degree in aquifer sediments from locations where groundwater chemistry indicated nitrate- and sulfate-reduction, respectively. The results of this study suggest that FISH may be a useful tool for providing a link between laboratory microcosms and groundwater measurements made in situ necessary to better demonstrate the potential for natural attenuation at complex PAH contaminated sites.

Microporous Organic Polymers Based on Hyper-Crosslinked Coal Tar: Preparation and Application for Gas Adsorption.

Science.gov (United States)

Gao, Hui; Ding, Lei; Bai, Hua; Li, Lei

2017-02-08

Hyper-crosslinked polymers (HCPs) are promising materials for gas capture and storage, but high cost and complicated preparation limit their practical application. In this paper, a new type of HCPs (CTHPs) was synthesized through a one-step mild Friedel-Crafts reaction with low-cost coal tar as the starting material. Chloroform was utilized as both solvent and crosslinker to generate a three-dimensional crosslinked network with abundant micropores. The maximum BET surface area of the prepared CTHPs could reach up to 929 m 2  g -1 . Owing to the high affinity between the heteroatoms on the coal-tar building blocks and the CO 2 molecules, the adsorption capacity of CTHPs towards CO 2 reached up to 14.2 wt % (1.0 bar, 273 K) with a high selectivity (CO 2 /N 2 =32.3). Furthermore, the obtained CTHPs could adsorb 1.27 wt % H 2 at 1.0 bar and 77.3 K, and also showed capacity for the capture of high organic vapors at room temperature. In comparison with other reported porous organic polymers, CTHPs have the advantages of low-cost, easy preparation, and high gas-adsorption performance, making them suitable for mass production and practical use in the future. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Porous carbon nanosheets from coal tar for high-performance supercapacitors

Science.gov (United States)

He, Xiaojun; Ma, Hao; Wang, Jingxian; Xie, Yuanyang; Xiao, Nan; Qiu, Jieshan

2017-07-01

A hydroxide-template strategy coupled with in-situ chemical activation is reported for the first time to fabricate porous carbon nanosheets (PCNSs) from coal tar. The thin PCNSs feature abundant short pores accessible for fast ion transport and high specific surface area up to 3235 m2 g-1 for ion adsorption. As electrodes for supercapacitors, the PCNSs show a high capacitance of 296.2 F g-1 at 0.05 A g-1 in 6 M KOH electrolyte, an excellent rate performance with a capacitance of 220.7 F g-1 at 20 A g-1 and a superior cycle stability with over 97.2% capacitance retention after 11000 charge-discharge cycles at 3.5 A g-1. This work paves a new way for efficient fabrication of sheet-like carbon materials with tuned porous structure from polycyclic aromatic hydrocarbons for high performance supercapacitors.

Nuclear graphite based on coal tar pitch; behavior under neutron irradiation between 400 and 14000C

International Nuclear Information System (INIS)

Mottet, P.; Fillatre, A.; Schill, R.; Micaud, G.

1977-01-01

Two nuclear grades of coal tar pitch coke graphites have been developed and tested under neutron irradiation. The neutron irradiation induced dimensional changes between 400 and 1400 0 C, at fluences up to 1,2.10 22 n.cm -2 PHI.FG show a behavior comparable to anisotropic petroleum coke graphites. Less than 10% variation in thermal expansion, maximum decrease by a factor four in thermal conductivity, and large increase of the Young modulus have been observed

Distilling tar; distillation, destructive

Energy Technology Data Exchange (ETDEWEB)

Brash, P; Young, W

1866-09-17

The tarry residue, which separates on treating crude shale oil with sulfuric acid, is redistilled, in the manner described in Specification No. 1278, A.D. 1866, together with shale. Previous to the distillation, the acid is neutralized with lime, or may be separated by blowing steam into the tar and adding salt. The purified tar thus obtained is absorbed by ashes, or is mixed with lime or other alkaline matter, or the shale may be mixed with lime and distilled with the tar, which is allowed to flow over and through the shale during the process. The tar obtained in the purification of natural paraffin may be similarly utilized.

Process of transforming tars, etc

Energy Technology Data Exchange (ETDEWEB)

1929-04-11

A process is described for treating tars obtained by carbonization, at high or low temperature, of coals, lignites, shales, and other carbonaceous materials or fractions of these tars, for obtaining products of greater value, consisting of polymerizing or saturating the unstable hydrocarbons in the presence of catalyzers by the progressing action particularly of halogenated metals, such as titanium tetrachloride, iron chloride, etc. and applying a known process of recovery, the disclosed process leading to an important reduction of final losses.

Detailed grouping and functional composition of neutral substances in low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Kalechits, I V; Salimgareeva, F G; Popova, N I; Kurbangaleeva, D K; Klykova, G G

1955-01-01

The grouping and the functional composition of the neutral substances in coal tar were characterized by means of adsorption on silica gel with subsequent chemical analysis of each fraction. The neutral materials were obtained by consecutive treatment of a C/sub 6/H/sub 6/ solution of coal tar with 10 percent alkali and 5 percent H/sub 2/SO/sub 4/ to remove the phenols and the bases. The data show that of the neutral substances (only 75% were identified) 40.5% were aromatic hydrocarbons. Based on a study of all of the data, it was proposed that 90% of the composition of coal tars is aromatic. The physical constants of the separated fractions were determined and are presented in tabular form.

Recovery of very viscous lubricating oils from shale-tar, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1918-01-22

A process is disclosed for the recovery of very viscous lubricating oils from brown-coal tar and shale tar, consisting in driving off from the crude tar or the tar freed from volatile constituents after removal of paraffin by precipitation with a volatile solvent such as acetone or one of its homologs, the light oils more or less completely with superheated steam from about 200 to 250/sup 0/C without any outside heating over a free flame.

Coal tar phototoxicity: characteristics of the smarting reaction

International Nuclear Information System (INIS)

Diette, K.M.; Gange, R.W.; Stern, R.S.; Arndt, K.A.; Parrish, J.A.

1985-01-01

The properties and ultraviolet exposure parameters of tar smarts were examined in an effort to elucidate the mechanisms involved. It was show that irradiation with 1 minimal smarting dose (MSD) of UVA immediately following tar removal lowered the MSD for 6 h, demonstrated by subsequent challenge with UVA. Following 3 MSDs this memory effect was demonstrable for 24 h. The smarting reaction was area dependent--smaller areas of exposure require higher doses of UVA to induce smarting. Smarting followed reciprocity over a 6-fold range of irradiances (2-12.5 mW/cm2) but higher irradiances required higher doses of UVA, perhaps due to a delay in the recognition and reporting of smarting. The smarting reaction and delayed erythema due to UVA and tar were equally blocked by sunscreen

Advanced Acid Gas Separation Technology for the Utilization of Low Rank Coals

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, Jeff

2012-12-31

Air Products has developed a potentially ground-breaking technology – Sour Pressure Swing Adsorption (PSA) – to replace the solvent-based acid gas removal (AGR) systems currently employed to separate sulfur containing species, along with CO{sub 2} and other impurities, from gasifier syngas streams. The Sour PSA technology is based on adsorption processes that utilize pressure swing or temperature swing regeneration methods. Sour PSA technology has already been shown with higher rank coals to provide a significant reduction in the cost of CO{sub 2} capture for power generation, which should translate to a reduction in cost of electricity (COE), compared to baseline CO{sub 2} capture plant design. The objective of this project is to test the performance and capability of the adsorbents in handling tar and other impurities using a gaseous mixture generated from the gasification of lower rank, lignite coal. The results of this testing are used to generate a high-level pilot process design, and to prepare a techno-economic assessment evaluating the applicability of the technology to plants utilizing these coals.

Removal of phenol by powdered activated carbon prepared from coal gasification tar residue.

Science.gov (United States)

Wang, Xiong-Lei; Shen, Jun; Niu, Yan-Xia; Wang, Yu-Gao; Liu, Gang; Sheng, Qing-Tao

2018-03-01

Coal gasification tar residue (CGTR) is a kind of environmentally hazardous byproduct generated in fixed-bed coal gasification process. The CGTR extracted by ethyl acetate was used to prepare powdered activated carbon (PAC), which is applied later for adsorption of phenol. The results showed that the PAC prepared under optimum conditions had enormous mesoporous structure, and the iodine number reached 2030.11 mg/g, with a specific surface area of 1981 m 2 /g and a total pore volume of 0.92 ml/g. Especially, without loading other substances, the PAC, having a strong magnetism, can be easily separated after it adsorbs phenol. The adsorption of phenol by PAC was studied as functions of contact time, temperature, PAC dosage, solution concentration and pH. The results showed a fast adsorption speed and a high adsorption capacity of PAC. The adsorption process was exothermic and conformed to the Freundlich models. The adsorption kinetics fitted better to the pseudo-second-order model. These results show that CGTR can be used as a potential adsorbent of phenols in wastewater.

Controllable growth of nanostructured carbon from coal tar pitch by chemical vapor deposition

International Nuclear Information System (INIS)

Liu Xuguang; Yang Yongzhen; Ji Weiyun; Liu Hongyan; Zhang Chunyi; Xu Bingshe

2007-01-01

The direct synthesis of vapor grown carbon fibers with different diameters was achieved by the pyrolysis of coal tar pitch by chemical vapor deposition. The products were characterized by field-emission scanning electron microscopy, high resolution transmission electron microscopy, X-ray diffraction and Raman spectroscopy. The experimental results demonstrated that ferrocene content, reaction temperature and Ar flow rate strongly influenced the yield and nature of nanostructured carbon materials, pure carbon microbeads, with diameter distribution ranging from 450 to 650 nm, were also obtained in the absence of catalyst, uniform and straight carbon nanofibers with the outer diameter of about 115 nm were obtained and curl and thick carbon fibers with narrow diameter distribution of 300-350 nm were produced

Fungal cultures of tar bush and creosote bush for production of two phenolic antioxidants (pyrocatechol and gallic acid).

Science.gov (United States)

Ventura, J; Gutiérrez-Sanchez, G; Rodríguez-Herrera, R; Aguilar, C N

2009-01-01

'Tar bush' and 'creosote bush' were substrates of fungal cultivation for tannase production and gallic acid and pyrocatechol accumulation. Aspergillus niger GH1 grew similarly on both plant materials under solid state culture conditions, reaching maximal levels after 4 d. Fungal strain degraded all tannin content of creosote bush after 4 d of fermentation and >75 % of tar bush after 5 d. Higher level of tannase activity was detected in tar bush fermentation. Biotransformation of tannins to gallic acid was high (93 % in creosote bush and 89 % in tar bush). Pyrocatechol was released poorly. Kinetic parameters of tannin conversion were calculated.

Determination of phenol in tar

Energy Technology Data Exchange (ETDEWEB)

Dierichs, A; Heinichen, G

1955-01-01

During low-temperature carbonization of lignite, the phenols and other oxygenated compounds appear both in the aqueous-process liquor and in the tar. Measurements of these oxygenated components resulting from low-temperature carbonization may serve as a parameter for the classification of lignites. However, such measurements are complicated by the instability of the tar and the complex nature of some of the acidic substances. Difficulties with the previous methods of analysis are reviewed. The present method outlines separation of aqueous-process liquor from lignite tar in a Fischer retort, followed by determination of phenols and fatty acids in the tar phase. The jacketed tar receiver is washed with 300 milliliter xylol and treated with aqueous caustic washes. Neutral oils are separated from the aqueous alkali solution. It is then extracted with ether and finally acidified with HCl. Solids are filtered off, and phenols and fatty acids are separated by Na/sub 2/CO/sub 3/ solution.

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line

International Nuclear Information System (INIS)

Kienzler, Aude; Mahler, Barbara J.; Van Metre, Peter C.; Schweigert, Nathalie; Devaux, Alain; Bony, Sylvie

2015-01-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity. - Highlights: • Co-exposure to runoff from coal-tar-sealcoated pavement and UVA caused DNA damage. • Significant genotoxicity occurred with a 1:100 dilution of runoff. • Runoff collected up to 36 d following coal-tar-sealcoat application was genotoxic. • Exposure to runoff from sealed pavement impaired an important DNA repair pathway. • Repair capacity was impaired with a 1:10 dilution of runoff (1:100 not

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line

Energy Technology Data Exchange (ETDEWEB)

Kienzler, Aude, E-mail: aude.kienzler@entpe.fr [Université de Lyon, UMR LEHNA 5023, USC INRA, ENTPE, rue Maurice Audin, Vaulx-en-Velin F-69518 (France); Mahler, Barbara J., E-mail: bjmahler@usgs.gov [U.S. Geological Survey, 1505 Ferguson Lane, Austin, TX 78754 (United States); Van Metre, Peter C., E-mail: pcvanmet@usgs.gov [U.S. Geological Survey, 1505 Ferguson Lane, Austin, TX 78754 (United States); Schweigert, Nathalie [Université de Lyon, UMR LEHNA 5023, USC INRA, ENTPE, rue Maurice Audin, Vaulx-en-Velin F-69518 (France); Devaux, Alain, E-mail: alain.devaux@entpe.fr [Université de Lyon, UMR LEHNA 5023, USC INRA, ENTPE, rue Maurice Audin, Vaulx-en-Velin F-69518 (France); Bony, Sylvie, E-mail: bony@entpe.fr [Université de Lyon, UMR LEHNA 5023, USC INRA, ENTPE, rue Maurice Audin, Vaulx-en-Velin F-69518 (France)

2015-07-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity. - Highlights: • Co-exposure to runoff from coal-tar-sealcoated pavement and UVA caused DNA damage. • Significant genotoxicity occurred with a 1:100 dilution of runoff. • Runoff collected up to 36 d following coal-tar-sealcoat application was genotoxic. • Exposure to runoff from sealed pavement impaired an important DNA repair pathway. • Repair capacity was impaired with a 1:10 dilution of runoff (1:100 not

Pyrolysis and hydropyrolysis performance of Shendong and Pingshuo coal

Energy Technology Data Exchange (ETDEWEB)

Shiping Huang; Bo Wu; Yunpeng Zhao; Lijun Jin; Haoquan Hu [Dalian University of Technology, Dalian (China). Institute of Coal Chemical Engineering

2007-07-01

Pyrolysis and hydropyrolysis of Shendong (SD) and Pingshuo (PS) coal were performed from 500 to 700{sup o}C in a fixed-bed reactor and the product distribution and gas evolution of both processes were analyzed. The results show that, the tar yields of both PS coal and SD coal reach the highest value, about 17 wt% and 13 wt% respectively at temperature 650{sup o}C for pyrolysis. However, the tar yields of PS coal get to the highest value, about 20 wt% at temperature 650{sup o}C, and the tar yields of SD coal are improving with temperature increasing, about 12 wt% at temperature 700{sup o}C for hydropyrolysis. The tar yields of PS coal are higher than those of SD coal at the same conditions for both pyrolysis and hydropyrolysis. The total gas yield of PS coal is higher than that of SD coal for pyrolysis, but lower for hydropyrolysis.

Pyrolysis at low-temperature of Mequinenza coal

Energy Technology Data Exchange (ETDEWEB)

Chorower, C

1940-01-01

In the low-temperature distillation of Mequinenza coal 13 to 14.5% of tar was obtained in the carbonizing unit and 10.7 to 12.0% in the rotary drum with or without steam. The yield of semicoke was 65 to 70.5%; the gas production was 91 to 109 liter per kilogram. The tar was distilled with and without steam, the fractions were freed from phenol and paraffin and purified by treatment with H/sub 2/SO/sub 4/. The coal tested was in many respects more like mineral coal than soft coal (thus, the liquid tar was of higher specific gravity, was free from resins and lower in paraffin and higher in phenol than in the case of soft coal). The pitch content of the tar was very slight, the yield of viscous oils was high. By distillation with steam 32% of benzine was obtained. Of the high S content established in the coking 8.5% was present in the benzine, 6.3% in the motor oil and 5.6% in the lubricating oil from the tar.

Determination of coal tar and creosote constituents in the aquatic environment

International Nuclear Information System (INIS)

Hale, R.C.; Aneiro, K.M.

1997-01-01

Creosote and its parent material, coal tar, are complex mixtures. Assessment of their fate and concentrations in the environment needs to consider a wide variety of both compounds and matrices. Analyses are typically complicated, consisting of sample extraction, purification and chromatography-based final characterization steps. Several new techniques have been introduced to reduce or simplify the number of steps, solvent and time required. Recently developed extraction methods include supercritical fluid, accelerated solvent, microwave and solid-phase microextraction. On-line purification and coupling of extraction and chromatography have also emerged. HPLC and GC remain the major tools for performing the final separations. Application of mass spectrometry has increased as more reliable, versatile and less expensive units have become available, such as the ion trap and mass selective detectors. Fluorescence and diode array UV, in concert with HPLC, and C-, S- and N-selective gas chromatographic detectors are also being applied

Microstructure and properties of lignite tar and pitch. Part II

Energy Technology Data Exchange (ETDEWEB)

Walther, H

1954-01-01

Photomicrographs reveal the presence of crystalline wax which affects the working properties in lignite tars and pitch. The crystals are large needles after slow cooling and small after rapid cooling. The crystals are paraffinic in character. All samples were nonhomogeneous. Thus the properties of lignite tar and pitch are varied by the source of the lignite and history of the specimen, neither softening point nor dropping point seems to satisfactorily characterize these tars. The samples exhibit thixotropic behavior characteristic of a structural viscosity and show hysteresis loops on varying the working rate. The variations have hindered use of lignite tars and pitches except where solubility in a solvent such as coal tar oil can be used to advantage.

Recovery of very viscous lubricating oils from shale-tar, etc

Energy Technology Data Exchange (ETDEWEB)

Erdmann, E

1919-09-10

Modification of the process covered by German Patent 335,190 for recovering very viscous lubricating oils, consisting, in place of brown-coal tar, deparafinned peat tar being subjected to the treatment with superheated steam from about 200 to 250/sup 0/C or to heating in vacuum at a temperature below 250/sup 0/C.

Topical tazarotene vs. coal tar in stable plaque psoriasis

Energy Technology Data Exchange (ETDEWEB)

Kumar, U.; Kaur, I.; Dogra, S.; De, D.; Kumar, B. [Postgraduate Institute of Medical Education & Research, Chandigarh (India)

2010-07-15

The efficacy of topical tazarotene has not previously been compared with the conventional topical treatment of crude coal tar (CCT) in stable plaque psoriasis. In this nonblinded side-to-side comparison study, patients with chronic stable plaque psoriasis, who had bilaterally symmetrical plaques on the limbs, applied 0.1% tazarotene gel on the right side and 5% CCT ointment on the left side once daily for 12 weeks followed by an 8-week treatment-free follow up period. Severity of psoriatic lesions and response to treatment was evaluated by scoring erythema, scaling and induration (ESI). Of 30 patients recruited, 27 could be assessed. In the per-protocol analysis, the mean percentage reduction in ESI score at the end of the treatment period was 74.15% {+-} 9.43 and 77.37% {+-} 10.93 with tazarotene and CCT, respectively (P {gt} 0.05). A reduction in ESI score of {gt} 75% was seen in 11 (40.74%) and 16 (59.26%) patients with tazarotene and CCT, respectively, at the end of 12 weeks. Side-effects were seen in 48.14% of patients treated with tazarotene, but in no patient treated with CCT. Tazarotene 0.1% gel has comparable clinical efficacy to CCT 5% ointment. CCT ointment remains a cost-effective therapy for plaque psoriasis.

A cost comparison of nuclear and fossil power for the Alberta tar sands

International Nuclear Information System (INIS)

Sochaski, R.O.; Smith, D.W.

1977-04-01

One technique envisaged for commercial development of the Alberta tar sands is in-situ removal of bitumen by injection of steam into the formation at high temperature and pressure. The 3000 MW of thermal power required for a typical 20 Gg/d plant could be supplied by a nuclear reactor. Accordingly, an economic comparison was made between a CANDU organic-cooled reactor and a conventional coal-fired station, using a variety of financial ground rules. This analysis shows that for debt-financed cases, nuclear power has essentially no economic competition from coal. For equity cases, the competitive position of a coal-fired station is heavily dependent on the cost of coal delivered to the tar sands area, discount rate, amortization period and inflation rate. (author)

Fuel production from microwave assisted pyrolysis of coal with carbon surfaces

International Nuclear Information System (INIS)

Mushtaq, Faisal; Mat, Ramli; Ani, Farid Nasir

2016-01-01

Highlights: • MW heating of coal was carried out with uniformly distributed carbon surfaces. • The effects of carbon loading, MW power and N 2 flow rate were investigated. • Heating profile, pyrolysis products are influenced by the process variables. • Highest coal-tar obtained when final temperature sustained for longer duration. • Coal-tar is mainly composed of aromatics and saturated aliphatics hydrocarbons. - Abstract: In this study, coal solids were subjected to Microwave (MW) pyrolysis conditions. Coconut Activated Carbon (CAC) solids used as a MW absorber was distributed uniformly over coal solids to reduce hotspots. Three process parameters; CAC loading, MW power and N 2 flow rate were studies on pyrolysis heating performance. The highest coal-tar yield of 18.59 wt% was obtained with 600 W, 75 wt% CAC loading and 4 Liter per Minute (LPM) of N 2 flow rate. This improved coal-tar yield is mainly of the fact that higher MW power and CAC loading produced sustained pyrolysis conditions for longer duration for the complete conversion of pyrolysis solids. The coal-tar was composed mainly of aromatics (naphthalenes, benzenes and xylene) and saturated aliphatics (alkanes and alkenes) hydrocarbons. The gas produced from pyrolysis of coal is mainly of H 2 40.23–65.22 vol%.

In situ solidification/stabilization pilot study for the treatment of coal tar contaminated soils and river sediments

International Nuclear Information System (INIS)

Lawson, M.A.; Venn, J.G.; Pugh, L.B.; Vallis, T.

1996-01-01

Coal tar contamination was encountered at a former coal gasification site in soils below the groundwater table, and in the sediments of the adjacent river. Ex situ remediation techniques at this site would be costly because of the need to dewater the impacted media. In situ solidification/stabilization was tested to evaluate its effectiveness. Treatability testing was performed to evaluate a Portland cement/fly ash binder system with added stabilizing agents. Results were sufficiently promising to warrant pilot testing. Grout containing Portland cement, fly ash, organically modified clay, and granular activated carbon was pilot tested at the site. Test specimens were collected and tested to evaluate durability, compressive strength, and permeability. The samples were extracted by several methods and analyzed to measure the leachable concentrations of organic compounds and metals. Results indicated acceptable physical characteristics. Leachable concentrations of most polynuclear aromatic compounds were decreased

Investigation of changes in {delta}{sup 13}C of PAHs during phytoremediation of coal tar-contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Mick Cooper; Cheng-Gong Sun; Margaret Smith; Harry Duncan; Colin Snape [University of Nottingham, Nottingham (United Kingdom). School of Chemical Environmental and Mining Engineering

2007-07-01

It has been shown that phytoremediation of polyaromatic hydrocarbon (PAH) contaminated land is a useful, low cost, low maintenance method of cleaning up land at former gas and coking works. However, PAH degradation in the soil and sediment is slow, but PAHs may be degraded through properly stimulated soil micro-organisms. Here we describe a laboratory trial, employing the clover Trifolium pretense (L.)(TP), which was grown in samples of soil contaminated by fresh coal tar, and in soil heavily contaminated by PAHs, obtained from a former coking works. As the latter substrate was 'naturally' contaminated, it contained both pure PAHs and their derivatives, and was thus considered fully 'weathered', and contained recalcitrant PAH species. Conventional analytical techniques (for example, GC-MS) generally provide little information on the source of pollutants such as PAHs. Previous work has established, however, that significant differences existed in the {sup 13}C/{sup 12}C isotopic ratios between PAHs from various sources. Source apportionment of PAH contamination by stable isotope analysis is a powerful technique, but one which assumes that isotopic fractionation is not a significant factor in aged or bioaltered matrices. Phytoremediation trials described here have been utilised in order to determine whether or not any such fractionation of {sup 13}C occurs during the process. Although PAH distributions can be markedly altered by biodegradation, it has been demonstrated that, for low temperature coal tar, the carbon stable isotopic values of the parent PAHs remain fairly constant. 22 refs., 2 figs., 5 tabs.

Comprehensive database of Manufactured Gas Plant tars. Part C. Heterocyclic and hydroxylated polycyclic aromatic hydrocarbons.

Science.gov (United States)

Gallacher, Christopher; Thomas, Russell; Lord, Richard; Kalin, Robert M; Taylor, Chris

2017-08-15

Coal tars are a mixture of organic and inorganic compounds that were by-products from the manufactured gas and coke making industries. The tar compositions varied depending on many factors such as the temperature of production and the type of retort used. For this reason a comprehensive database of the compounds found in different tar types is of value to understand both how their compositions differ and what potential chemical hazards are present. This study focuses on the heterocyclic and hydroxylated compounds present in a database produced from 16 different tars from five different production processes. Samples of coal tar were extracted using accelerated solvent extraction (ASE) and derivatized post-extraction using N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) with 1% trimethylchlorosilane (TMCS). The derivatized samples were analysed using two-dimensional gas chromatography combined with time-of-flight mass spectrometry (GCxGC/TOFMS). A total of 865 heterocyclic compounds and 359 hydroxylated polycyclic aromatic hydrocarbons (PAHs) were detected in 16 tar samples produced by five different processes. The contents of both heterocyclic and hydroxylated PAHs varied greatly with the production process used, with the heterocyclic compounds giving information about the feedstock used. Of the 359 hydroxylated PAHs detected the majority would not have been be detected without the use of derivatization. Coal tars produced using different production processes and feedstocks yielded tars with significantly different heterocyclic and hydroxylated contents. The concentrations of the individual heterocyclic compounds varied greatly even within the different production processes and provided information about the feedstock used to produce the tars. The hydroxylated PAH content of the samples provided important analytical information that would otherwise not have been obtained without the use of derivatization and GCxGC/TOFMS. Copyright © 2017 John Wiley & Sons, Ltd.

Microbial community structure changes during bioremediation of PAHs in an aged coal-tar contaminated soil by in-vessel composting

Energy Technology Data Exchange (ETDEWEB)

Antizar-Ladislao, B.; Spanova, K.; Beck, A.J.; Russell, N.J. [University of London Imperial College for Science Technology & Medicine, Ashford (United Kingdom)

2008-06-15

The microbial community structure changes of an aged-coal-tar soil contaminated with polycyclic aromatic hydrocarbons (PAHs) were investigated during simulated bioremediation at the laboratory-scale using an in-vessel composting approach. The composting reactors were operated using a logistic three-factor factorial design with three temperatures (T = 38, 55 or 70 {sup o}C), four soil to green-waste amendment ratios (S:GW = 0.6:1, 0.7:1, 0.8:1 or 0.9:1 on a dry weight basis) and three moisture contents (MC = 40%, 60% or 80%). Relative changes in microbial populations were investigated by following the dynamics of phospholipid fatty acid (PLFA) signatures using a {sup 13}C-labeled palmitic acid internal standard and sensitive GC/MS analysis during in-vessel composting over 98 days. The results of this investigation indicated that fungal to bacterial PLFA ratios were significantly influenced by temperature (p<0.05), and Gram-positive to Gram-negative bacterial ratios were significantly influenced by temperature (p<0.001) and S:GW ratio (p<0.01) during in-vessel composting. Additionally, the Gram-positive to Gram-negative bacterial ratios were correlated to the extent of PAH losses)<0.005) at 70{sup o}C.

Microstructural characteristics of toluene and quinoline-insolubles from coal-tar pitch and their cokes

Energy Technology Data Exchange (ETDEWEB)

Panaitescu, C. [University POLITEHNICA Bucharest, Faculty of Industrial Chemistry, Fuel Laboratory, Polizu St. 1, Sector 1, 011061, Bucharest (Romania); Predeanu, G. [Metallurgical Research Institute, Department of Raw Materials, Mehadia St. 39, Sector 6, 060543 Bucharest (Romania)

2007-08-01

The structural composition of coal-tar pitch used in the preparation of the special binder-pitch, was determined with special emphasis on the optical properties of the {beta}-resins, as typical components necessary to obtain electrodes of best quality through the pyrogenetic processes of baking and graphitization. In addition to raw toluene- and quinoline-insolubles (TI, QI), the corresponding cokes were analysed to evaluate, by structural composition and microtexture, the behaviour of pitch fractions during carbonization. The results suggest the dependence of the texture development on the type of toluene- and quinoline-insolubles and {beta}-resins during processing conditions, which influence the mesophase formation. An original and important result of the carbopetrographical study is represented by the identification and evaluation of {beta}-resins in the coke texture. (author)

PRODUCTION OF CARBON PRODUCTS USING A COAL EXTRACTION PROCESS

Energy Technology Data Exchange (ETDEWEB)

Dady Dadyburjor; Philip R. Biedler; Chong Chen; L. Mitchell Clendenin; Manoj Katakdaunde; Elliot B. Kennel; Nathan D. King; Liviu Magean; Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo

2004-08-31

This Department of Energy National Energy Technology Laboratory sponsored project developed carbon products, using mildly hydrogenated solvents to extract the organic portion of coal to create synthetic pitches, cokes, carbon foam and carbon fibers. The focus of this effort was on development of lower cost solvents, milder hydrogenation conditions and improved yield in order to enable practical production of these products. This technology is needed because of the long-term decline in production of domestic feedstocks such as petroleum pitch and coal tar pitch. Currently, carbon products represents a market of roughly 5 million tons domestically, and 19 million tons worldwide. Carbon products are mainly derived from feedstocks such as petroleum pitch and coal tar pitch. The domestic supply of petroleum pitch is declining because of the rising price of liquid fuels, which has caused US refineries to maximize liquid fuel production. As a consequence, the long term trend has a decline in production of petroleum pitch over the past 20 years. The production of coal tar pitch, as in the case of petroleum pitch, has likewise declined significantly over the past two decades. Coal tar pitch is a byproduct of metallurgical grade coke (metcoke) production. In this industry, modern metcoke facilities are recycling coal tar as fuel in order to enhance energy efficiency and minimize environmental emissions. Metcoke production itself is dependent upon the production requirements for domestic steel. Hence, several metcoke ovens have been decommissioned over the past two decades and have not been replaced. As a consequence sources of coal tar are being taken off line and are not being replaced. The long-term trend is a reduction in coal tar pitch production. Thus import of feedstocks, mainly from Eastern Europe and China, is on the rise despite the relatively large transportation cost. To reverse this trend, a new process for producing carbon products is needed. The process must be

Comparison of Soxhlet and Shake Extraction of Polycyclic Aromatic Hydrocarbons from Coal Tar Polluted Soils Sampled in the Field

DEFF Research Database (Denmark)

Lindhardt, Bo; Holst, Helle; Christensen, Thomas Højlund

1994-01-01

This study compares three extraction methods for PAHs in coal tar polluted soil: 3-times repeated shaking of the soil with dichloromethane-methanol (1:1), Soxhlet extraction with dichloromethane, and Soxhlet extraction with dichloromethane followed by Soxhlet extraction with methanol....... The extraction efficiencies were determined for ten selected PAHs in triplicate samples of six soils sampled at former gasworks sites. The samples covered a wide range of PAH concentrations, from 0.6 to 397 mg/kg soil. Soxhlet extraction with dichloromethane followed by Soxhlet extraction with methanol...

Fundamental studies of coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

1995-01-01

The authors have examined the pyrolysis of Argonne samples of Wyodak and Illinois No. 6 coal in argon, undecane, Tetralin, and water. The effects of the pyrolysis on individual particles of coal were monitored visually in a cell with diamond windows capable of operation to temperature and pressures in excess of 500{degrees}C and 3000 psi. The changes in the particles from ambient to 460{degrees}C were recorded in real time on video tape, and images were then taken from the tape record and analyzed. The study showed that in argon both coals developed tars at 350{degrees}-370{degrees}C. The tars then quickly evaporated, leaving core particles remarkably similar in size and shape to the initial particles. These observations suggest that coal does not melt nor become fully liquid when heated. Nor does the softened coal undergo crosslinking to generate coke. Rather the simple loss of volatiles leaves behind the core residue as coke. Contrary to the common view, there appears to be no link between the bond-breaking processes yielding tar and the interaction of the coal with H-donors leading to liquefaction. Water as a medium was surprising in its effect. Both coals began to shrink at 300{degrees}-350{degrees}C, with the effect appearing to be more of an erosion rather than a uniform loss of substance as seen in Tetralin. The Wyodak continued to shrink to 460{degrees}C to about half its initial size. With the Illinois No. 6 coal, however, the process reversed at around 420{degrees}C, and the particles appeared to grow with the evolution of a tar, continuing to 460{degrees}C. The authors submit that this final observation is evidence for hydrothermal synthesis of hydrocarbons at these conditions.

The catalytic cracking mechanism of lignite pyrolysis char on tar

International Nuclear Information System (INIS)

Lei, Z.; Huibin, H.; Xiangling, S.; Zhenhua, M.; Lei, Z.

2017-01-01

The influence of different pyrolysis conditions for tar catalytic cracking will be analyzed according to the lignite pyrolysis char as catalyst on pyrolytic tar in this paper. The pyrolysis char what is the by-product of the cracking of coal has an abundant of pore structure and it has good catalytic activity. On this basis, making the modified catalyst when the pyrolysis char is activation and loads Fe by impregnation method. The cracking mechanism of lignite pyrolytic tar is explored by applying gas chromatograph to analyze splitting products of tar. The experimental results showed that: (1) The effect of tar cracking as the pyrolysis temperature, the heating rate, the volatilization of pyrolysis char and particle size increasing is better and better. The effect of the catalytic and cracking of lignite pyrolysis char in tar is best when the heating rate, the pyrolysis temperature, the volatiles of pyrolysis char, particle size is in specific conditions.(2) The activation of pyrolysis char can improve the catalytic effect of pyrolysis char on the tar cracking. But it reduces the effect of the tar cracking when the pyrolysis char is activation loading Fe. (author)

A process for briquetting coal with the production of briquets with high resistance to crushing

Energy Technology Data Exchange (ETDEWEB)

Ono, M; Ito, S; Nakagava, K

1983-02-08

Finely ground coal is mixed with a binder with a softening point of greater than or equal to 30 degrees and with heavy coal tar products, the mixture is molded with the formation of briquets in a two roller press. The mixing is conducted in heated steam or waste gases from a horizontal, helical mixer. The coal is subsequently irrigated by the melted binder and heavy coal tar products. The heavy coal tar products are a bottom residue formed by condensation of volatile products in a gas stream from coking which contains particles of coal and coke. Briquets with a point compression strength of 50 plus or minus 4 kilograms per sq. cur. and a bulk tensity of 1.17 grams per cubic centimeter are produced from a mixture which contains 6 percent binder, 80 percent coal and 20 percent heavy coal tar products.

29 CFR 779.357 - May qualify as exempt 13(a)(2) establishments; classification of coal sales.

Science.gov (United States)

2010-07-01

... principal raw material, such as sales of coal for the production of coke, coal gas, coal tar, or electricity... production of coke, coal gas, coal tar, or electricity. This is distinguished from sales of coal for use in...; classification of coal sales. 779.357 Section 779.357 Labor Regulations Relating to Labor (Continued) WAGE AND...

De-agglomeration and homogenisation of nanoparticles in coal tar pitch-based carbon materials

Science.gov (United States)

Gubernat, Maciej; Tomala, Janusz; Frohs, Wilhelm; Fraczek-Szczypta, Aneta; Blazewicz, Stanislaw

2016-03-01

The aim of the work was to characterise coal tar pitch (CTP) modified with selected nanoparticles as a binder precursor for the manufacture of synthetic carbon materials. Different factors influencing the preliminary preparative steps in the preparation of homogenous nanoparticle/CTP composition were studied. Graphene flakes, carbon black and nano-sized silicon carbide were used to modify CTP. Prior to introducing them into liquid CTP, nanoparticles were subjected to sonication. Various dispersants were used to prepare the suspensions, i.e. water, ethanol, dimethylformamide (DMF) and N-methylpyrrolidone (NMP).The results showed that proper dispersant selection is one of the most important factors influencing the de-agglomeration process of nanoparticles. DMF and NMP were found to be effective dispersants for the preparation of homogenous nanoparticle-containing suspensions. The presence of SiC and carbon black nanoparticles in the liquid pitch during heat treatment up to 2000 °C leads to the inhibition of crystallite growth in carbon residue.

De-agglomeration and homogenisation of nanoparticles in coal tar pitch-based carbon materials

Energy Technology Data Exchange (ETDEWEB)

Gubernat, Maciej [AGH University of Science and Technology, Faculty of Materials Science and Ceramics (Poland); Tomala, Janusz [SGL Carbon Polska S.A. (Poland); Frohs, Wilhelm [SGL CARBON GmbH (Germany); Fraczek-Szczypta, Aneta; Blazewicz, Stanislaw, E-mail: blazew@agh.edu.pl [AGH University of Science and Technology, Faculty of Materials Science and Ceramics (Poland)

2016-03-15

The aim of the work was to characterise coal tar pitch (CTP) modified with selected nanoparticles as a binder precursor for the manufacture of synthetic carbon materials. Different factors influencing the preliminary preparative steps in the preparation of homogenous nanoparticle/CTP composition were studied. Graphene flakes, carbon black and nano-sized silicon carbide were used to modify CTP. Prior to introducing them into liquid CTP, nanoparticles were subjected to sonication. Various dispersants were used to prepare the suspensions, i.e. water, ethanol, dimethylformamide (DMF) and N-methylpyrrolidone (NMP).The results showed that proper dispersant selection is one of the most important factors influencing the de-agglomeration process of nanoparticles. DMF and NMP were found to be effective dispersants for the preparation of homogenous nanoparticle-containing suspensions. The presence of SiC and carbon black nanoparticles in the liquid pitch during heat treatment up to 2000 °C leads to the inhibition of crystallite growth in carbon residue.

Distillation of tar and tar fractions in the presence of surface-active coke

Energy Technology Data Exchange (ETDEWEB)

Jaeppelt, A; Klaus, J

1943-01-01

The tar obtained by low-temperature carbonization of Upper Silesian gas coke and fractions from this tar were distilled in the presence of different grades of coke dust with varying surface activity; the coke had been activated by steam in the course of its production by low-temperature carbonization. The surface activity of the coke dusts was measured by determining the heat of wetting with C/sub 6/H/sub 6/. Tar and coke dust, both anhydrous, were mixed in a kneading machine in such proportions that the capillaries of the dust were saturated and enough ''externally'' bound tar was present to permit briquetting. The briquets were distilled without cracking and with steam as heating medium. The yield and quality of the distillate depended on the magnitude of the internal surface of the coke dust used; a mixture of a very active coke from brown coal and tar yielded a distillate with Conradson carbon residue of 1.34 percent, asphalt content 6.1 percent and eta/sub 20/ 5.4/sup 0/ E. as compared with C residue of 10.95 percent, asphalt content 33.5 percent and eta/sub 20/ 123.6/sup 0/ E. of the distillate obtained in the absence of surface-active coke. Even higher-boiling fractions can be improved by this treatment, although it is preferable to use oils with an initial boiling point below 300/sup 0/. The ratio of oil to adsorbent is not critical, but better results were obtained with higher percentages of added coke dust. The process in its present form is not suited for the conversion of crude creosote to useful phenols.

Forensic assessment of polycyclic aromatic hydrocarbons at the former Sydney Tar Ponds and surrounding environment using fingerprint techniques

International Nuclear Information System (INIS)

MacAskill, N. Devin; Walker, Tony R.; Oakes, Ken; Walsh, Margaret

2016-01-01

Polycyclic aromatic hydrocarbons (PAHs) were assessed spatially and temporally within and adjacent to a former coking and steel manufacturing facility in Sydney, Nova Scotia, Canada. Concentrations of PAHs were measured in surface soils, marine and estuary sediments prior to and during remediation of the Sydney Tar Ponds (STPs) site which was contaminated by nearly a century of coking and steel production. Previous studies identified PAHs in surficial marine sediments within Sydney Harbour, which were considered to be derived from STP discharges. Numerous PAH fingerprint techniques (diagnostic ratios, principal component analysis, quantitative and qualitative analysis) were applied to soil and sediment samples from the STPs and surrounding area to identify common source apportionment of PAHs. Results indicate coal combustion (from historical residential, commercial and industrial uses) and coal handling (from historic on-site stockpiling and current coal transfer and shipment facilities) are likely the principal source of PAHs found in urban soils and marine sediments, consistent with current and historical activities near these sites. However, PAH fingerprints associated with STP sediments correlated poorly with those of urban soils and marine sediments, but were similar to coal tar, historically consistent with by-products produced by the former coking operations. This study suggests PAH contamination of Sydney Harbour sediments and urban soils is largely unrelated to historic coking operations or recent remediation of the STPs site, but rather a legacy of extensive use of coal for a variety of activities. - Highlights: • PAHs were measured in soils and sediments near a former coking and steel facility. • Previous studies identified tar residues as main source of PAHs in marine sediments. • PAH fingerprint techniques were used to identify common source apportionment. • Fingerprint techniques indicated common sources derived from coal, not tar residues

Influence of metal additives on pyrolysis behavior of bituminous coal by TG-FTIR analysis

Energy Technology Data Exchange (ETDEWEB)

Su, Wenjuan; Fang, Mengxiang; Cen, Jianmeng; Li, Chao; Luo, Zhongyang; Cen, Kefa [Zhejiang Univ., Hangzhou (China). State Key Lab. of Clean Energy Utilization

2013-07-01

To study the catalytic effects of alkali, alkaline earth and transition metal additives on coal pyrolysis behavior, bituminous coal loaded NaCl, KCl, CaCl{sub 2}, MgCl{sub 2}, FeCl{sub 3} and NiCl{sub 2} was respectively investigated using Thermogravimetry and Fourier Transform Infrared Spectroscopy (TG-FTIR). Results indicated that the maximum mass loss rate decreased under the metal additives in the primary pyrolysis stage. The total mass loss of pyrolysis was reduced in metals catalyzed pyrolysis except for Na loaded sample. Kinetic analysis was taken for all samples adopting the method of Coats-Redfern. Activation energy of raw coal in the primary pyrolysis stage was 92.15vkJ.mol{sup -1}, which was lowered to 44.59-73.42 kJ.mol{sup -1} under metal additives. The orders of catalytic effect for this bituminous coal were Mg > Fe > Ca > Ni > K > Na according to their activation energies. Several investigated volatiles including CH{sub 4}, CO{sub 2}, CO, toluene, phenol and formic acid were identified from FTIR spectra. The yields of CH{sub 4}, CO{sub 2}, toluene, phenol and formic acid were decreased, but the evolution of CO was increased. The presence of metals in the coal samples have been involved in a repeated bond-forming and bond-breaking process, which greatly hindered the release of tars during pyrolysis as the tar precursors were connected to coal/char matrix and were thermally cracked, becoming a part of char.

Isolation of CYP1A inducing components in coal tar fraction (F3) of Alaska north slope crude oil : a preliminary study

Energy Technology Data Exchange (ETDEWEB)

Saravanabhavan, G.; Brown, R.S. [Queen' s Univ., Kingston, ON (Canada). Dept. of Chemistry; Khan, C.W.; Hodson, P.V. [Queen' s Univ., Kingston, ON (Canada). Dept. of Biology

2004-07-01

Recent concerns regarding the effects of weathered crude oil on the early life stage of aquatic organisms are related to reports that blue sac disease (BSD) has been linked to larval fish exposed to crude oil. Studies have shown that a relationship exists between the induction of CYP1A enzymes and the occurrence of BSD in fish species. However, the mechanism of BSD is not fully understood. This study contributed to the Toxicity Identification and Evaluation (TIE) approach by isolating the CYP1A enzyme. An improved separation and analysis method for characterizing crude oil was also developed. Earlier studies revealed that the highest CYP1A activity occurred in the coal tar fraction of crude oil, which is rich in polycyclic aromatic hydrocarbons (PAH) and which contains many classes of compounds such as waxes, asphaltenes and resins. The TIE method included separation of these compound classes as well as a detailed characterization of the PAH classes. A solvent extraction method was also developed to fractionate the coal tar fraction into compound classes with particular emphasis on isolating PAH components. The study showed that fractions rich in PAH were responsible for a significant CYP1A induction in juvenile trout, but fractions poor in PAH did not. The solid phase extraction method offered better PAH fractions for further analysis by liquid chromatography.

Pyrolysis of coal in the presence of nitric oxide

Energy Technology Data Exchange (ETDEWEB)

Berkowitz, N; Dammeyer, W

1956-01-01

Examination of tars obtained by low-temperature carbonization of a subbituminous coal in the presence of NO suggests that NO will both retard thermal decomposition and inhibit secondary polymerization in the tar phase. But both reactions are subject to the condition that NO is present at the start of incipient pyrolysis (they do not occur if NO is admitted to the retorts at a point above the decomposition temperature of the coal), and their extent depends sharply upon the concentration of NO. At comparatively low partial pressure of NO, the dominant reaction is retardation of decomposition; significant modification of the tar, leading to a greater proportion of low-boiling material, is confined to high-partial pressure of NO. Conclusions, after analyzing tar yields and infrared spectra of tar fractions, are that the inhibition of secondary polymerization in the tar phase involves the transient attachment of NO to primary tar molecules, and that the inhibitory effect of NO is essentially temporary. Tars modified by NO do not appear to be more stable than normal tars in the presence of light, and their composition, as determined by infrared spectroscopy, is not perceptibly different.

Catalytic hydroprocessing of simulated coal tars. 1. Activity of a sulphided Ni-Mo/Al/sub 2/O/sub 3/ catalyst for the hydroconversion of model compounds

Energy Technology Data Exchange (ETDEWEB)

Lemberton, J.L.; Touzeyidio, M.; Guisnet, M. (Laboratoire de Catalyse en Chimie Organique CNRS, Poitiers (France))

1989-09-15

The conversion of tars from coal pyrolysis into light aromatics, such as BTX (benzene-toluene-xylenes) and naphthalene, requires the hydrocracking of heavy polyaromatics in the presence of nitrogen- and oxygen-containing compounds. The hydroconversion of phenanthrene, which occurs through bifunctional catalysis, was chosen as a model reaction. It was carried out over a sulphided Ni-Mo/Al/sub 2/O/sub 3/ catalyst (Ketjen 153) in the presence of carbazole and 1-naphthol. Carbazole poisons slightly through coking both the hydrogenating and the acid sites of the catalyst. 1-Naphthol has a more significant deactivating effect: the hydrogenating sites of the catalyst are poisoned by the water eliminated from 1-naphthol and the acid sites by coke generated by 1-naphthol. Lastly, the hydrogenating activity of the catalyst is not substantially affected in the presence of carbazole and 1-naphthol, but its cracking activity is much reduced, making it impossible for the catalyst to achieve the hydrocracking of phenanthrene into into light aromatics. 5 figs, 21 refs., 1 tab.

Preparation of fulvic acid and low-molecular organic acids by oxidation of weathered coal humic acid

Energy Technology Data Exchange (ETDEWEB)

Shinozuka, T.; Ito, A.; Sasaki, O.; Yazawa, Y.; Yamaguchi, T. [Chiba Institute of Technolgy, Chiba (Japan). Dept. of Industrial Chemistry

2002-07-01

Weathered coal contains much humic acid and a little fulvic acid. Therefore, the production of fulvic acid, the most valuable humic substance because of its water-solubility, was examined by ozone and hydrogen peroxide oxidation of humic acid extracted form Xinjiang (China) weathered coal. The resulting products of the oxidation were water soluble fulvic acid and organic acids, mainly formic acid and oxalic acid. The product yield of fulvic acid was 20 (C%) and that of organic acids were 39 (C%) for formic and acid 13 (C%) for oxalic acid. The formed fulvic acid showed a higher content of oxygen and carboxyl groups, than those of the extracted one from the original weathered coal.

Fuel oil from low-temperature carbonization of coal

Energy Technology Data Exchange (ETDEWEB)

Thau, A

1941-01-01

A review has been given of German developments during the last 20 years. Four methods for the low-temperature carbonization of coal have been developed to the industrial stage; two involving the use of externally heated, intermittent, metallic chamber ovens; and two employing the principle of internal heating by means of a current of gas. Tar from externally heated retorts can be used directly as fuel oil, but that from internally heated retorts requires further treatment. In order to extend the range of coals available for low-temperature carbonization, and to economize metals, an externally heated type of retort constructed of ceramic material has been developed to the industrial stage by T. An excellent coke and a tar that can be used directly as fuel oil are obtained. The properties of the tar obtained from Upper Silesian coal are briefly summarized.

Study on the Inference Factors of Huangling Coking Coal Pyrolysis

Science.gov (United States)

Du, Meili; Yang, Zongyi; Fan, Jinwen

2018-01-01

In order to reasonably and efficiently utilize Huangling coking coal resource, coal particle, heating rate, holding time, pyrolysis temperature and others factors were dicussed for the influence of those factor on Huangling coking coal pyrolysis products. Several kinds of coal blending for coking experiments were carried out with different kinds of coal such as Huangling coking coal, Xida coal with high ash low sufur, Xinghuo fat coal with hign sulfur, Zhongxingyi coking coal with high sulfur, Hucun lean coal, mixed meager and lean coal. The results shown that the optimal coal particle size distribution was 0.5~1.5mm, the optimal heating rate was 8°C/min, the optimal holding time was 15min, the optimal pyrolysis temperature was 800°C for Huangling coking coal pyrolysis, the tar yield increased from 4.7% to 11.2%. The maximum tar yield of coal blending for coking under the best single factor experiment condition was 10.65% when the proportio of Huangling coking coal was 52%.

In Situ Catalytic Pyrolysis of Low-Rank Coal for the Conversion of Heavy Oils into Light Oils

Directory of Open Access Journals (Sweden)

Muhammad Nadeem Amin

2017-01-01

Full Text Available Lighter tars are largely useful in chemical industries but their quantity is quite little. Catalytic cracking is applied to improve the yield of light tars during pyrolysis. Consequently, in situ upgrading technique through a MoS2 catalyst has been explored in this research work. MoS2 catalyst is useful for the conversion of high energy cost into low energy cost. The variations in coal pyrolysis tar without and with catalyst were determined. Meanwhile, the obtained tar was analyzed using simulated distillation gas chromatograph and Elemental Analyzer. Consequently, the catalyst reduced the pitch contents and increased the fraction of light tar from 50 to 60 wt.% in coal pyrolysis tar. MoS2 catalyst increased the liquid yield from 18 to 33 (wt.%, db and decreased gas yield from 27 to 12 (wt.%, db compared to coal without catalyst. Moreover, it increased H content and hydrogen-to-carbon ratio by 7.9 and 3.3%, respectively, and reduced the contents of nitrogen, sulphur, and oxygen elements by 8.1%, 15.2%, and 23.9%, respectively, in their produced tars compared to coal without catalyst.

Extraction of low-temperature tar by various alcohols

Energy Technology Data Exchange (ETDEWEB)

Hara, N; Osawa, M; Azuma, H

1948-01-01

MeOH was the most effective of the alcohols tested (MeOH to pentanol) in extracting acid components from low-temperature tar. The optimum concentrations of MeOH were 70 to 80% for 1 extraction and 70 to 75% for repeated or continuous extractions when the solvent-tar ratio was 1:1. By 2 to 3 extractions neutral oil could be separated in about 90% yield including > 3% acidic oil.

Assessing the role of coal in the world energy future

International Nuclear Information System (INIS)

Hibbard Junior, W.R.

1981-01-01

Ten recent extensive studies of long range energy futures were evaluated and a consensus of findings developed. Progress toward the consensus was determined. In the next 20 years the United States will need all of the coal, nuclear, oil shale and tar sands that public consensus and the legislatures will permit. Concerns include the cost and availability of OPEC oil, energy efficiency, acid rain, and carbon dioxide build-up. (Author) [pt

Measurement and investigation of effects of coal tar pitch fractions in nuclear graphite properties

International Nuclear Information System (INIS)

Fatemi, K.; Fatoorehchian, S.; Ahari Hashemi, F.; Ahmadi, Sh.

2003-01-01

Coal tar pitch has a complex chemical structure. Determination of α, β, γ fractions, is one of the methods to get information about its properties. In graphite fabrication it plays a role as a binder for coke particles. During the thermal treatment it carbonizes and changes to a secondary coke. This has considerable affects on the graphite properties. In this paper, determination of α, β, γ-1 fraction in three different types of pitches have been carried out. Graphite specimens have been fabricated by using these pitches and anisotropy coke in laboratory scale. The graphite properties have been compared with the nuclear graphite prototype. The comparison of the results showed that the density and compression strength are appreciable while the anisotropy factor of properties is about one. The linear thermal expansion in graphite from Iranian pitch had a better, result, where it stands in the nuclear range of usage. As a result, our studies showed that the graphite properties are affected by properties of pitch fractions, where it can be used as a proper sample for the graphite fabrication

Contribution of PAHs from coal-tar pavement sealcoat and other sources to 40 U.S. lakes

Science.gov (United States)

Van Metre, Peter C.; Mahler, Barbara J.

2010-01-01

Contamination of urban lakes and streams by polycyclic aromatic hydrocarbons (PAHs) has increased in the United States during the past 40 years. We evaluated sources of PAHs in post-1990 sediments in cores from 40 lakes in urban areas across the United States using a contaminant mass-balance receptor model and including as a potential source coal-tar-based (CT) sealcoat, a recently recognized source of urban PAH. Other PAH sources considered included several coal- and vehicle-related sources, wood combustion, and fuel-oil combustion. The four best modeling scenarios all indicate CT sealcoat is the largest PAH source when averaged across all 40 lakes, contributing about one-half of PAH in sediment, followed by vehicle-related sources and coal combustion. PAH concentrations in the lakes were highly correlated with PAH loading from CT sealcoat (Spearman's rho=0.98), and the mean proportional PAH profile for the 40 lakes was highly correlated with the PAH profile for dust from CT-sealed pavement (r=0.95). PAH concentrations and mass and fractional loading from CT sealcoat were significantly greater in the central and eastern United States than in the western United States, reflecting regional differences in use of different sealcoat product types. The model was used to calculate temporal trends in PAH source contributions during the last 40 to 100 years to eight of the 40 lakes. In seven of the lakes, CT sealcoat has been the largest source of PAHs since the 1960s, and in six of those lakes PAH trends are upward. Traffic is the largest source to the eighth lake, located in southern California where use of CT sealcoat is rare.

Science of coal-to-oil conversion

Energy Technology Data Exchange (ETDEWEB)

Spencer, W D

1944-01-01

A general review is given of the principles of the most important commercial processes for obtaining oil from coal, and of the yields obtained by, and special features of each process. The composition of typical tars obtained by the low-temperature carbonization of coal, yields of products other than tar, estimated costs of running a plant of 700 tons daily capacity and annual British statistics on the industry from 1930 through 1938 are tabulated. The text is chiefly concerned with the various types of retorts, which have been developed for use in this process. Economics and cost of production are discussed.

Effect of the polymerization with formaldehyde on the thermal reactivity of a low-temperature coal tar pitch

Energy Technology Data Exchange (ETDEWEB)

Jose L. Crespo; Ana Arenillas; Jose A. Vin; Roberto Garcia; Colin E. Snape; Sabino R. Moinelo [Instituto Nacional del Carbon (CSIC), Oviedo (Spain)

2005-04-01

The influence of polymerization with formaldehyde on the thermal reactivity of a low-temperature coal tar pitch has been investigated. The mechanism and extent of the polymerization depends on the catalyst used, the greatest extent of polymerization being achieved under basic catalytic conditions. After the polymerization treatment, samples were carbonized at 420{sup o}C and the products were characterized by optical microscopy. According to the results, polymerization with formaldehyde increases the reactivity of the pitch, giving rise to increased carbonization yields and leading to the formation of the mesophase with milder conditions. The polymerization process also affects the morphology of the resultant anisotropic material, giving rise to the formation of irregularly shaped mesophase particles and reducing the optical texture size of the anisotropic domains, giving mosaic texture, especially when basic catalysis is used. 36 refs., 11 figs., 5 tabs.

Dandruff, seborrheic dermatitis, and psoriasis drug products containing coal tar and menthol for over-the-counter human use; amendment to the monograph. Final rule

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-03-15

The Food and Drug Administration (FDA) is issuing a final rule amending the final monograph (FM) for over-the-counter (OTC) dandruff, seborrheic dermatitis, and psoriasis drug products to include the combination of 1.8 percent coal tar solution and 1.5 percent menthol in a shampoo drug product to control dandruff. FDA did not receive any comments or data in response to its previously proposed rule to include this combination. This final rule is part of FDA's ongoing review of OTC drug products.

A Tat-grafted anti-nucleic acid antibody acquires nuclear-localization property and a preference for TAR RNA

International Nuclear Information System (INIS)

Jeong, Jong-Geun; Kim, Dong-Sik; Kim, Yong-Sung; Kwon, Myung-Hee

2011-01-01

Highlights: → We generate ' H3 Tat-3D8' by grafting Tat 48-60 peptide to VH CDR of 3D8 scFv antibody. → H3 Tat-3D8 antibody retains nucleic acid binding and hydrolyzing activities. → H3 Tat-3D8 acquires a preference for TAR RNA structure. → Properties of Tat 48-60 is transferred to an antibody via Tat-grafting into a CDR. -- Abstract: The 3D8 single chain variable fragment (3D8 scFv) is an anti-nucleic acid antibody that can hydrolyze nucleic acids and enter the cytosol of cells without reaching the nucleus. The Tat peptide, derived from the basic region of the HIV-1 Tat protein, translocates to cell nuclei and has TAR RNA binding activity. In this study, we generated a Tat-grafted antibody ( H3 Tat-3D8) by replacing complementarity-determining region 3 (CDR3) within the VH domain of the 3D8 scFv with a Tat 48-60 peptide (GRKKRRQRRRPPQ). H3 Tat-3D8 retained the DNA-binding and DNA-hydrolyzing activity of the scFv, and translocated to the nuclei of HeLa cells and preferentially recognized TAR RNA. Thus, the properties associated with the Tat peptide were transferred to the antibody via Tat-grafting without loss of the intrinsic DNA-binding and hydrolyzing activities of the 3D8 scFv antibody.

Investigation of virgin coals and coals subjected to a mild acid treatment

Energy Technology Data Exchange (ETDEWEB)

Clark, T.M.; Evans, B.J.; Wynter, C.; Pollak, H.; Taole, S.; Radcliffe, D. [University of Michigan, Ann Arbor, MI (United States). Dept. of Chemistry

1998-06-01

A quantitative determination of the relative marcasite/pyrite contents in virgin coals is possible by means of {sup 57}Fe Moessbauer spectroscopy. Complications arise however, when iron-containing silicates, carbonates, or other salts are present. The application of a mild chemical treatment involving hydrofluoric acid has been employed to remove these Fe-containing phases while leaving the iron-disulfide phases unaffected. Several South African coal samples with non-iron disulfide, Fe-containing phases ranging from 18 to 30 weight percent were subjected to a hydrofluoric acid leaching at room temperature. The loss of mineral matter with HF leaching correlates well with the mineral matter residue following low temperature ashing. The {sup 57}Fe Moessbauer spectra of the resulting coal samples indicate that only FeS{sub 2} phases are present and the absence of appreciable quantities of marcasite in the coals.

Effect of acid treatment on thermal extraction yield in ashless coal production

Energy Technology Data Exchange (ETDEWEB)

Chunqi Li; Toshimasa Takanohashi; Takahiro Yoshida; Ikuo Saito; Hideki Aoki; Kiyoshi Mashimo [National Institute of Advanced Industrial Science and Technology, Tsukuba (Japan). Institute for Energy Utilization

2004-04-01

Coals of different ranks were acid-treated in aqueous methoxyethoxy acetic acid (MEAA), acetic acid (AA), and HCl. The acid-treated coals were extracted with polar N-methyl-2-pyrrolidinone (NMP) and nonpolar 1-methylnaphthalene (1MN) solvents at temperatures from 200 to 360{sup o}C for 10 60 min. The thermal extraction yields with NMP for some acid-treated low-rank coals increased greatly; for example, the extraction yield for Wyodak coal (%C; 75.0%) increased from 58.4% for the raw coal to 82.9% for coal treated in 1.0 M MEAA. Conversely, the extraction yields changed minimally for all the acid-treated coals extracted in 1-MN. The type and concentration of acid affected the extraction yield when NMP was used as the extraction solvent. With increasing MEAA concentration from 0.01 to 0.1 M, the extraction yield for Wyodak coal increased from 66.3 to 81.4%, and subsequently did not change clearly with concentration. Similar changes in the extraction yield with acid concentration were also observed with AA and HCl. The de-ashing ratio for coals acid-treated in MEAA, AA, and HCl also increased greatly with concentration from 0.01 to 0.1 M, which corresponded to the change in the thermal extraction yield in NMP. For the acid-treated coals, high extraction yields were obtained at lower extraction temperatures and shorter extraction times than for the raw coal. The mechanisms for the acid treatment and thermal extraction are discussed. 27 refs., 6 figs., 3 tabs.

Co-pyrolysis of waste tire/coal mixtures for smokeless fuel, maltenes and hydrogen-rich gas production

International Nuclear Information System (INIS)

Bičáková, Olga; Straka, Pavel

2016-01-01

Highlights: • Co-pyrolysis of waste tires/coal mixtures yields mainly smokeless fuel (55–74 wt%). • Alternatively, the smokeless fuel can serve as carbonaceous sorbent. • The obtained tar contained maltenes (80–85 wt%) and asphaltenes (6–8 wt%). • Tar from co-pyrolysis can serve as heating oil or a source of maltenes for repairing of asphalt surfaces. • The hydrogen-rich gas was obtained (61–65 vol% H_2, 24–25 vol% CH_4, 1.4–2 vol% CO_2). - Abstract: The processing of waste tires with two different types of bituminous coal was studied through the slow co-pyrolysis of 1 kg of waste tire/coal mixtures with 15, 30 and 60 wt% waste tires on a laboratory scale. The waste tire/coal mixtures were pyrolysed using a quartz reactor in a stationary bed. The mixtures were heated at a rate 5 °C/min up to the final temperature of 900 °C with a soaking time of 30 min at the required temperature. The mass balance of the process and the properties of the coke and tar obtained were evaluated, further, the influence of the admixture in the charge on the amount and composition of the obtained coke and tar was determined. It was found that the smokeless fuel/carbonaceous sorbent and a high yield of tar for further use can be obtained through the slow co-pyrolysis. The obtained tars contained mostly maltenes (80–85 wt%). FTIR analysis showed that the maltenes from the co-pyrolysis of coal/waste tires exhibited significantly lower aromaticity as compared with that from coal alone. The gas obtained from pyrolysis or co-pyrolysis of waste tire/coal mixtures contained a high amount of hydrogen (above 60 vol%) and methane (above 20 vol%).

Hydrothermal pretreatment of coal

Energy Technology Data Exchange (ETDEWEB)

Ross, D.S.

1989-12-21

We have examined changes in Argonne Premium samples of Wyodak coal following 30 min treatment in liquid water at autogenous pressures at 150{degrees}, 250{degrees}, and 350{degrees}C. In most runs the coal was initially dried at 60{degrees}C/1 torr/20 hr. The changes were monitored by pyrolysis field ionization mass spectrometry (py-FIMS) operating at 2.5{degrees}C/min from ambient to 500{degrees}C. We recorded the volatility patterns of the coal tars evolved over that temperature range, and in all cases the tar yields were 25%--30% of the starting coal on mass basis. There was essentially no change after the 150{degrees}C treatment. Small increases in volatility were seen following the 250{degrees}C treatment, but major effects were seen in the 350{degrees} work. The tar quantity remained unchanged; however, the volatility increased so the temperature of half volatility for the as-received coal of 400{degrees}C was reduced to 340{degrees}C. Control runs with no water showed some thermal effect, but the net effect from the presence of liquid water was clearly evident. The composition was unchanged after the 150{degrees} and 250{degrees}C treatments, but the 350{degrees} treatment brought about a 30% loss of oxygen. The change corresponded to loss of the elements of water, although loss of OH'' seemed to fit the analysis data somewhat better. The water loss takes place both in the presence and in the absence of added water, but it is noteworthy that the loss in the hydrothermal runs occurs at p(H{sub 2}O) = 160 atm. We conclude that the process must involve the dehydration solely of chemically bound elements of water, the dehydration of catechol is a specific, likely candidate.

Evolution of bacterial community during bioremediation of PAHs in a coal tar contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Lors, C.; Ryngaert, A.; Perie, F.; Diels, L.; Damidot, D. [University of Lille, Lille (France)

2010-11-15

The monitoring of a windrow treatment applied to soil contaminated by mostly 2, 3- and 4-ring PAHs produced by coal tar distillation was performed by following the evolution of both PAH concentration and the bacterial community. Total and PAH-degrading bacterial community structures were followed by 165 rRNA PCR-DGGE in parallel with quantification by bacterial counts and 16 PAH measurements. Six months of biological treatment led to a strong decrease in 2-, 3- and 4-ring PAH concentrations (98, 97 and 82%, respectively). This result was associated with the activity of bacterial PAH-degraders belonging mainly to the Gamma proteobacteria, in particular the Enterobacteria and Pseudomonas genera which were detected over the course of the treatment. This group was considered to be a good bioindicator to determine the potential PAH biodegradation of contaminated soil. Conversely other species like the Beta proteobacteria were detected after 3 months when 2-, 3- and 4-ring PAHs were almost completely degraded. Thus presence of the Beta proteobacteria group could be considered a good candidate indicator to estimate the endpoint of biotreatment of this type of PAH contaminated soil.

Current status of U.S. coal utilization and non-fuel uses of fossil fuels

International Nuclear Information System (INIS)

Song, C.S.; Schobert, H.; Scaroni, A.W.

1997-01-01

An understanding of the current situation is important for projecting the future direction of coal utilization. The world's annual consumption of coal in 1995 was 5104.01 million short tons (MST, 1 short ton = 0.907 metric ton). Coal plays a very important role in the US energy supply; US coal production in 1995 totaled 1033 MST, including 611.1 MST of bituminous coal, 328.4 MST of subbituminous coal, 86.1 MST of lignite, and 4.1 MST of anthracite. US coal consumption totaled 940.6 MST, with 88.1% in electric utilities, 3.5% in coke plants, 7.8% for other industrial uses, and only 0.6% in the residential and commercial sectors. The amount of fossil resources used for non-fuel purposes accounted for 8.4% of the total annual consumption in 1995. Non-fuel uses of fossil fuels particularly coal may become more important in the future. The demonstrated coal reserves in the world are large enough for consumption for over 220 years at the 1995 level, while proven oil reserves are only about 40 times the world's 1995 consumption level. Coal has several positive attributes when considered as a feedstock for aromatic chemicals, specialty chemicals, and carbon-based materials. Existing nonfuel uses of coals include (1) high temperature carbonization of bituminous and subbituminous coals to make metallurgical coke; (2) gasification of coal to make synthesis gases and other chemicals; (3) use of coal in manufacturing other materials such as activated carbons, carbon molecular sieves (CMS) and production of phosphorus (phosphoric acid); (4) the use of coal tars from carbonization and gasification for making aromatic and phenolic chemicals; (5) the use of coal tar pitch for making carbon fibers and activated carbon fibers; and (6) other non-fuel products derived from coal including combustion by-products. Coal may become more important both as an energy source and as the source of chemical feedstocks in the 21st century

A novel integrated process of coal pyrolysis and methane CO{sub 2} reforming

Energy Technology Data Exchange (ETDEWEB)

Jing Wang; Pengfei Wang; Lijun Jin; Haoquan Hu [Dalian University of Technology, Dalian (China)

2007-07-01

In the paper, a novel pyrolysis method, namely coal pyrolysis coupling with CO{sub 2} reforming of methane (CRMP) or catalytic pyrolysis of coal coupling with CO{sub 2} reforming of methane (CRMCP), for improving the tar yield of coal pyrolysis was introduced. The behaviours of YM coal in both processes were investigated and compared with pyrolysis under N{sub 2} and H{sub 2}. The results show that the tar yield of coal pyrolysis in both processes obviously increase compared with that in N{sub 2} or H{sub 2}. When YM coal pyrolysis was carried out in stream of mixture gas CH{sub 4}/CO{sub 2} (1:1) with the existence of the catalyst at 0.1 MPa and 800{sup o}C, the tar yield is 2.8 times for CRMP and 4.3 times for CRMCP as that of pyrolysis under N{sub 2} and 1.7 and 2.6 times as that of hydropyrolysis at the same conditions, respectively. Sulfur content of char obtained from CRMP and CRMCP process are lower, especially in CRMP process, than that from N{sub 2} or H{sub 2}. 16 refs., 4 figs., 1 tab.

Examination of soil contaminated by coal-liquids by size exclusion chromatography in 1-methyl-2-pyrrolidinone solution to evaluate interference from humic and fulvic acids and extracts from peat.

Science.gov (United States)

Morgan, T J; Herod, A A; Brain, S A; Chambers, F M; Kandiyoti, R

2005-11-18

Soil from a redundant coke oven site has been examined by extraction of soluble materials using 1-methyl-2-pyrrolidinone (NMP) followed by size exclusion chromatography (SEC) of the extracted material. The extracted material was found to closely resemble a high temperature coal tar pitch. Standard humic and fulvic acids were also examined since these materials are very soluble in NMP and would be extracted with pitch if present in the soil. Humic substances derived from peat samples and NMP-extracts of peats were also examined. The results show that the humic and fulvic substances were not extracted directly by NMP from peats. They were extracted using caustic soda solution and were different from the peat extracts in NMP. These results indicate that humic and fulvic acids were soluble in NMP in the protonated polyelectrolyte form but not in the original native polyelectrolyte form. The extraction of soil using NMP followed by SEC appears to be a promising method for identifying contamination by coal-based industries.

Cleavage and crosslinking of polymeric coal structures during pyrolysis

Energy Technology Data Exchange (ETDEWEB)

McMillen, D.F.; Malhotra, R.

1992-02-01

The ultimate objective of this project was to develop a better understanding of volatiles production to help optimize the yield and character of condensable coproducts during coal pyrolysis or mild gasification. The specific objectives were to (1) Develop pyrolysis procedures that minimize secondary reactions; and (2) Develop coal pretreatments that current knowledge suggests will prorate bond scission or prevent retrograde reactions. Our approach was to study the pyrolysis of coals and tar-loaded coals by using several techniques that span a range of heating rates and pressures. Slow-heating pyrolyses were performed at low pressures in the inlet of a field ionization mass spectrometer and at atmospheric pressures in a thermogravimetric analyzer. Moderately rapid-heating pyrolyses were performed in a vacuum TGA apparatus and in sealed silica ampules heated in a molten-salt bath. The fastest heating rates were achieved with laser pyrolysis at about 30,000 X/s. The high tar yield seen in this work where the entire volume of the coal particle becomes hot and fluid at very nearly the same time, taken together with the evident non-vapor transport of the tar under these conditions, emphasizes the importance of better understanding the development of fluidity during coal heating. This specifically includes the profound effects--long-recognized but poorly understood that mild oxidation has in suppressing coal fluidity. It also includes the more recently recognized fact that heating in the presence of an inert gas produced substantially greater fluidity than does heating in the presence of combustion gases, even if the conditions are very fuel rich and all the oxygen itself has already been consumed when the coal particles are encountered.

Synthesis of nanoporous carbons from mixtures of coal tar pitch and furfural and their application as electrode materials

Energy Technology Data Exchange (ETDEWEB)

Petrova, B.; Tsyntsarski, B.; Budinova, T.; Petrov, N.; Ania, C.O.; Parra, J.B.; Mladenov, M.; Tzvetkov, P.

2010-11-15

Synthetic nanoporous carbons are prepared by polymerization of mixtures containing coal tar pitch and furfural in different proportions, followed by carbonization of obtained solid product and steam activation of the carbonizate. The chemical composition of the initial mixture significantly affects the physicochemical properties (surface area, pore structure, electro resistance and amount of oxygen-containing groups on the surface) of the obtained materials. The incorporation of oxygen in the precursor mixture by means of furfural, has a strong influence in the synthetic step; increasing the furfural content facilitates the formation of a solid product characterized by a large oxygen content. Moreover, the solid product is more reactive towards activation as the furfural content increases, giving rise to nanoporous carbons with large surface areas and unique chemical features (high density of oxygen functionalities of basic nature). These nanoporous carbons have been investigated as electrodes in electrochemical applications. (author)

Characterization of the coal derived humic acids from Mukah, Sarawak as soil conditioner

Directory of Open Access Journals (Sweden)

Fong Sim Siong

2006-01-01

Full Text Available In Malaysia, abundant coal resources were found in Sarawak and Sabah. The utilization of coal resources, to date, is emphasized on the energy productions. The non-energy utilization as soil conditioner is unexplored. Therefore, this study attempted to characterize the coal humic acids extracted from Mukah coal and to evaluate its properties as soil conditioner. The coal humic acids from the regenerated sample were also assessed. The results revealed that different extractants and concentrations influenced the properties of humic acids. The extraction with KOH at 0.5 mol L-1 produced humic acids with low ash content and high acidic functional groups, which are substantial as soil conditioner. However, the yield was low. Regeneration of coal sample with 10% nitric acids improved the yield to an average of 83.45%. The acidic functional groups of nitrohumic acids were improved with the ash content remained at a low level.

Dissolved organic matter from soils contaminated by coal tars: towards a better understanding of its nature and reactivity

International Nuclear Information System (INIS)

Hanser, Ogier

2015-01-01

A large amount of wastelands inherited from former industrial activities contains persistent organic contamination (coal, coal tar...). While the regulation requires an evaluation of the contamination degree of these soils, it doesn't take into account the transformation byproducts such as polar compounds, poorly studied. Yet they solubilize in aqueous phase by percolation of meteoric waters through these contaminated sites. Despite the fact that literature targeting the fresh DOM is abundant, it is not directly transposable to the anthropogenic DOM coming from wastelands, which still need to be more precisely defined to improve our knowledge of this specific DOM and its evolution over time. A multi-technical approach was developed to comprehend the anthropogenic DOM coming from former coking and gas plant soils, thanks to a combination of laboratory experiments (under controlled conditions) and on field devices (lysimeters). Their study show that they contained a high aromatic DOM, while the aromatic polycyclic compounds only consist of a low proportion of the total DOM. Complementary experiences targeting the influence of some parameters (pH, hydrophobicity) suggest a strong link between the pH and the spatial DOM organization and a decrease in the apparent molecular weight with the hydrophobicity. Artificial aging experiences show an enrichment in polar condensed compounds leading to their water mobilization. (author) [fr

A DEVICE AND METHOD FOR MEASURING TAR IN A TAR-ENVIRONMENT

DEFF Research Database (Denmark)

2017-01-01

The present disclosure describes a device and corresponding method for measuring tar in a tar environment, e.g., a tar producing environment such as a stove or a combustion engine, based on UV absorption spectroscopy. A first measurement along an optical path in the tar environment is performed...

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line

Science.gov (United States)

Kienzler, Aude; Mahler, Barbara J.; Van Metre, Peter C.; Schweigert, Nathalie; Devaux, Alain; Bony, Sylvie

2015-01-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity.

Inclined fluidized bed system for drying fine coal

Science.gov (United States)

Cha, Chang Y.; Merriam, Norman W.; Boysen, John E.

1992-02-11

Coal is processed in an inclined fluidized bed dryer operated in a plug-flow manner with zonal temperature and composition control, and an inert fluidizing gas, such as carbon dioxide or combustion gas. Recycled carbon dioxide, which is used for drying, pyrolysis, quenching, and cooling, is produced by partial decarboxylation of the coal. The coal is heated sufficiently to mobilize coal tar by further pyrolysis, which seals micropores upon quenching. Further cooling with carbon dioxide enhances stabilization.

Preliminary Study on Benzoic Acid Adsorption from Crude Active Coals and Bentonite

Directory of Open Access Journals (Sweden)

Abbes Boucheta

2016-04-01

Full Text Available We studied the adsorption of pollutant benzoic acid by the modified bentonite of Maghnia (west of Algeria, and coal (Coal from the mines, southwest of Algeria, Bechar area under three forms, crude and activated. Kinetic data show that the balance of bentonite (as amended adsorbs organic acids better than activated and raw coal. Indeed, the intercalation of bentonite with benzoic acid causes an improvement in the texture of porous material, which allows its use in the adsorption of organic compounds. The adsorption isotherms (Langmuir and Freundlich indicate that the adsorption of benzoic acid by the coal and bentonite yielded results favorably. The results obtained showed the practical value of using the activated coal and bentonite (as amended in the field of remediation of water contaminated with organic pollutants

Cleavage and crosslinking of polymeric coal structures during pyrolysis. Final report

Energy Technology Data Exchange (ETDEWEB)

McMillen, D.F.; Malhotra, R.

1992-02-01

The ultimate objective of this project was to develop a better understanding of volatiles production to help optimize the yield and character of condensable coproducts during coal pyrolysis or mild gasification. The specific objectives were to (1) Develop pyrolysis procedures that minimize secondary reactions; and (2) Develop coal pretreatments that current knowledge suggests will prorate bond scission or prevent retrograde reactions. Our approach was to study the pyrolysis of coals and tar-loaded coals by using several techniques that span a range of heating rates and pressures. Slow-heating pyrolyses were performed at low pressures in the inlet of a field ionization mass spectrometer and at atmospheric pressures in a thermogravimetric analyzer. Moderately rapid-heating pyrolyses were performed in a vacuum TGA apparatus and in sealed silica ampules heated in a molten-salt bath. The fastest heating rates were achieved with laser pyrolysis at about 30,000 X/s. The high tar yield seen in this work where the entire volume of the coal particle becomes hot and fluid at very nearly the same time, taken together with the evident non-vapor transport of the tar under these conditions, emphasizes the importance of better understanding the development of fluidity during coal heating. This specifically includes the profound effects--long-recognized but poorly understood that mild oxidation has in suppressing coal fluidity. It also includes the more recently recognized fact that heating in the presence of an inert gas produced substantially greater fluidity than does heating in the presence of combustion gases, even if the conditions are very fuel rich and all the oxygen itself has already been consumed when the coal particles are encountered.

Solvent refining of low-temperature tar with liquid ammonia

Energy Technology Data Exchange (ETDEWEB)

Ishida, K

1953-01-01

The middle fractions of low-temperature tar were treated with mixed solutions of H/sub 2/O and liquid NH/sub 3/ at 0/sup 0/ and 20/sup 0/, and with liquid NH/sub 3/ at -10, 0, + 10, and 20/sup 0/, and phase equilibrium between tar acids, neutral oil, and solvents were studied. The distribution ratio ranged from less than 1 to greater than 1 when the solvent contained about 20 percent (by weight) H/sub 2/O. When the solvent contained less than 85 percent (by weight) NH/sub 3/, the yield of extract was small but the purity of phenols in the extracted oil was above 90 percent. Solvent containing about 85 percent NH/sub 3/ (by weight) is considered optimum for separating tar acids from oils. A novel definition is proposed for solvent selectivity as the difference between the concentration of the solute in the extract layer, on a solvent-free basis, and the concentration in the raffinate layer.

Coal-tar-based parking lot sealcoat: An unrecognized source of PAH to settled house dust

Science.gov (United States)

Mahler, B.J.; Van Metre, P.C.; Wilson, J.T.; Musgrove, M.; Burbank, T.L.; Ennis, T.E.; Bashara, T.J.

2010-01-01

Despite much speculation, the principal factors controlling concentrations of polycyclic aromatic hydrocarbons (PAH) in settled house dust (SHD) have not yet been identified. In response to recent reports that dust from pavement with coaltar-based sealcoat contains extremely high concentrations of PAH, we measured PAH in SHD from 23 apartments and in dust from their associated parking lots, one-half of which had coal-tar-based sealcoat (CT). The median concentration of total PAH (T-PAH) in dust from CT parking lots (4760 ??g/g, n = 11) was 530 times higher than that from parking lots with other pavement surface types (asphalt-based sealcoat, unsealed asphalt, concrete [median 9.0 ??g/g, n = 12]). T-PAH in SHD from apartments with CT parking lots (median 129 ??g/g) was 25 times higher than that in SHD from apartments with parking lots with other pavement surface types (median 5.1 ??g/g). Presence or absence of CT on a parking lot explained 48% of the variance in log-transformed T-PAH in SHD. Urban land-use intensity near the residence also had a significant but weaker relation to T-PAH. No other variables tested, including carpeting, frequency of vacuuming, and indoor burning, were significant. ?? 2010 American Chemical Society.

Exposure to runoff from coal-tar-sealed pavement induces genotoxicity and impairment of DNA repair capacity in the RTL-W1 fish liver cell line.

Science.gov (United States)

Kienzler, Aude; Mahler, Barbara J; Van Metre, Peter C; Schweigert, Nathalie; Devaux, Alain; Bony, Sylvie

2015-07-01

Coal-tar-based (CTB) sealcoat, frequently applied to parking lots and driveways in North America, contains elevated concentrations of polycyclic aromatic hydrocarbons (PAHs) and related compounds. The RTL-W1 fish liver cell line was used to investigate two endpoints (genotoxicity and DNA-repair-capacity impairment) associated with exposure to runoff from asphalt pavement with CTB sealcoat or with an asphalt-based sealcoat hypothesized to contain about 7% CTB sealcoat (AS-blend). Genotoxic potential was assessed by the Formamido pyrimidine glycosylase (Fpg)-modified comet assay for 1:10 and 1:100 dilutions of runoff samples collected from 5 h to 36 d following sealcoat application. DNA-repair capacity was assessed by the base excision repair comet assay for 1:10 dilution of samples collected 26 h and 36 d following application. Both assays were run with and without co-exposure to ultraviolet-A radiation (UVA). With co-exposure to UVA, genotoxic effects were significant for both dilutions of CTB runoff for three of four sample times, and for some samples of AS-blend runoff. Base excision repair was significantly impaired for CTB runoff both with and without UVA exposure, and for AS-blend runoff only in the absence of UVA. This study is the first to investigate the effects of exposure to the complex mixture of chemicals in coal tar on DNA repair capacity. The results indicate that co-exposure to runoff from CT-sealcoated pavement and UVA as much as a month after sealcoat application has the potential to cause genotoxicity and impair DNA repair capacity. Copyright © 2015 Elsevier B.V. All rights reserved.

Coal pyrolysis under hydrogen-rich gases

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Sun, C.; Li, B.; Liu, Z. [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion, Institute of Coal Chemistry

1998-04-01

To improve the economy of the pyrolysis process by reducing the hydrogen cost, it is suggested to use cheaper hydrogen-rich gases such as coke-oven gas (COG) or synthesis gas (SG) instead of pure hydrogen. The pyrolysis of Chinese Xianfeng lignite which was carried out with real COG and SG at 3-5 MPa, a final temperature of 650{degree}C and a heating rate of 5{degree}C/min in a 10g fixed-bed reactor is compared with coal pyrolysis with pure hydrogen and nitrogen under the same conditions. The results indicate that compared with hydropyrolysis at the same total pressure, the total conversion and tar yields from coal pyrolysis with COG and SG decreases while the unwanted water increases. However, at the same H{sub 2} partial pressure, the tar yields and yields of BBTX, PCX and naphthalene from the pyrolysis of coal with COG and SG are all significantly higher than those of hydropyrolysis. Therefore, it is possible to use COG and SG instead of pure hydrogen. 8 refs., 3 figs., 6 tabs.

Nitrosation and Nitration of Fulvic Acid, Peat and Coal with Nitric Acid.

Directory of Open Access Journals (Sweden)

Kevin A Thorn

Full Text Available Nitrohumic acids, produced from base extraction of coals and peats oxidized with nitric acid, have received considerable attention as soil ammendments in agriculture. The nitration chemistry however is incompletely understood. Moreover, there is a need to understand the reaction of nitric acid with natural organic matter (NOM in general, in the context of a variety of environmental and biogeochemical processes. Suwannee River NOM, Suwannee River fulvic acid, and Pahokee Peat fulvic acid were treated with 15N-labeled nitric acid at concentrations ranging from 15% to 22% and analyzed by liquid and solid state 15N NMR spectroscopy. Bulk Pahokee peat and Illinois #6 coal were also treated with nitric acid, at 29% and 40% respectively, and analyzed by solid state 15N NMR spectroscopy. In addition to nitro groups from nitration of aromatic carbon, the 15N NMR spectra of all five samples exhibited peaks attributable to nitrosation reactions. These include nitrosophenol peaks in the peat fulvic acid and Suwannee River samples, from nitrosation of phenolic rings, and N-nitroso groups in the peat samples, from nitrosation of secondary amides or amines, the latter consistent with the peat samples having the highest naturally abundant nitrogen contents. Peaks attributable to Beckmann and secondary reactions of the initially formed oximes were present in all spectra, including primary amide, secondary amide, lactam, and nitrile nitrogens. The degree of secondary reaction product formation resulting from nitrosation reactions appeared to correlate inversely with the 13C aromaticities of the samples. The nitrosation reactions are most plausibly effected by nitrous acid formed from the reduction of nitric acid by oxidizable substrates in the NOM and coal samples.

Co-pyrolysis of low rank coals and biomass: Product distributions

Energy Technology Data Exchange (ETDEWEB)

Soncini, Ryan M.; Means, Nicholas C.; Weiland, Nathan T.

2013-10-01

Pyrolysis and gasification of combined low rank coal and biomass feeds are the subject of much study in an effort to mitigate the production of green house gases from integrated gasification combined cycle (IGCC) systems. While co-feeding has the potential to reduce the net carbon footprint of commercial gasification operations, the effects of co-feeding on kinetics and product distributions requires study to ensure the success of this strategy. Southern yellow pine was pyrolyzed in a semi-batch type drop tube reactor with either Powder River Basin sub-bituminous coal or Mississippi lignite at several temperatures and feed ratios. Product gas composition of expected primary constituents (CO, CO{sub 2}, CH{sub 4}, H{sub 2}, H{sub 2}O, and C{sub 2}H{sub 4}) was determined by in-situ mass spectrometry while minor gaseous constituents were determined using a GC-MS. Product distributions are fit to linear functions of temperature, and quadratic functions of biomass fraction, for use in computational co-pyrolysis simulations. The results are shown to yield significant nonlinearities, particularly at higher temperatures and for lower ranked coals. The co-pyrolysis product distributions evolve more tar, and less char, CH{sub 4}, and C{sub 2}H{sub 4}, than an additive pyrolysis process would suggest. For lignite co-pyrolysis, CO and H{sub 2} production are also reduced. The data suggests that evolution of hydrogen from rapid pyrolysis of biomass prevents the crosslinking of fragmented aromatic structures during coal pyrolysis to produce tar, rather than secondary char and light gases. Finally, it is shown that, for the two coal types tested, co-pyrolysis synergies are more significant as coal rank decreases, likely because the initial structure in these coals contains larger pores and smaller clusters of aromatic structures which are more readily retained as tar in rapid co-pyrolysis.

Process for treating the dialyzed spent liquor from sulphonic acid containing sulfur minerals or tar oils or ammonium salts

Energy Technology Data Exchange (ETDEWEB)

Wernicke, E A

1936-08-09

Process for working up the dialyzate from sulfonic acid, sulfur-containing mineral or tar oils, or their ammonium salts, characterized by the combination of known steps, in the dialyzate being reacted with alkaline-earth oxide, hydroxide, or carbonate, and the resulting slightly soluble sulfate being filtered off and evaporated if necessary.

Receiving demulsifying agent from the acid tar

Energy Technology Data Exchange (ETDEWEB)

Nikitina, A.A.; Belyaeva, A.S.; Kunakova, R.V. [FGBIHE ' Ufa State Academy of Economics and Services' , Ufa (Russian Federation); Movsumzade, E.M. [FGBIHE ' Ufa State Petroleum Technological Univ.' , Ufa (Russian Federation); Lapidus, A.L. [Russian Academy of Sciences, Moscow (Russian Federation). N.D. Zelinsky Institute of Organic Chemistry

2012-07-01

The processing of wastes of petrochemical production makes it possible to reduce the price of produced commodity of petroleum products substantially. Bitumen, fuel oils, tars and other mixture of heavy organic compounds are widely used in road construction, in paint and cable industries, manufacture of roofing materials, are used as boiler and furnace fuel, fuel for marine diesel engines, raw material for the production of modifying additives, fillers, surfaceactive substances, etc. (orig.)

Treatment of lignite tars, etc

Energy Technology Data Exchange (ETDEWEB)

1936-08-07

A process is described for treating tars such as lignite tar, shale tar, or peat tar, and similar tars, characterized by the fact that the tar is rectified to about 240/sup 0/C and the residue brought to a temperature above 50/sup 0/C after diluting with a product of the type of gasoline or ligroin at about 30/sup 0/C and treated with selective solvents preferably low-boiling phenols and eventually with water.

Process and apparatus for recovering of oil, bitumen, tar, resins, etc

Energy Technology Data Exchange (ETDEWEB)

1921-11-06

A process for recovering oil, bitumen, tar, and resins from oil shale, oil sands, Fuller's earth, peat, brown coal, mineral coal, and wood, through direct action of superheated steam on the material, is characterized by the fact that superheated steam with or without mixing of inert gases at a temperature, which lies below the decomposition temperature of the material being treated, is passed through the material with a high velocity. It leaves through nozzles, used in steam turbines. A method of carrying out the process in which solution medium is used for action on the material is characterized by the fact that solvents such as benzine and benzol are mixed with steam in different quantities.

Distilling coal

Energy Technology Data Exchange (ETDEWEB)

Blythe, F C

1914-09-14

In the destructive distillation of bituminous coal, heavy hydrocarbon oil, such as petroleum, kerosine, shale oil, and heavy tar oil, obtained in some cases during the process, is added to the coal, which is then distilled under pressure and at a comparatively low temperature regulated so as to produce a large proportion of hydrocarbon oils and a small proportion of permanent gas. In one method, about 5 to 10 parts of hydrocarbon oil are mixed with 100 parts of crushed or ground coal, and the mixture is heated in a closed vessel, provided in some cases with an agitator, under a pressure of about 60 lb/in/sup 2/, and the temperature may be gradually raised to 350/sup 0/C and then to about 500/sup 0/C. The heating may be by means of superheated steam with or without external heat.

Chemical coal conversion yesterday, today, and tomorrow; Der Chemierohstoff Kohle: gestern, heute und morgen

Energy Technology Data Exchange (ETDEWEB)

Talbiersky, J. [UCP Chemicals AG, Wien (Austria)

2007-01-15

Shortage in mineral oil and gas as well as a high price level have caused a renaissance in coal conversion technologies, at the end of the 70's. Today we have a similar situation. Now coal coversion technologies will be in the focus again but hopefully as a longterm strategy. The most important coal conversion technologies as liquefaction, gasification, coking and calcium carbide synthesis are discussed regarding their use for the production of chemicals. The most important source for aromatic chemicals from coal is till now coal tar with an availability of 22 Mio. t/a. The manufacturing of coal tar is discussed as an example for making aromatic products from a complex feed stock that you get by the fixed bed gasification, coal liquefaction and coking. Also the special marketing strategy that is necessary to be competitive against products from the petroindustry. It can be expected, that coal gasification as a source for synthesis gas will become more and more important. Synthesis gas is the access to aliphatic hydrocarbons by Fischer Tropsch synthesis and to methanol, a chemical with a high synthetic potential. Also the new hydrothermal carbonization of biomass to synthetic coal is mentioned. (orig.)

Research investigations in oil shale, tar sand, coal research, advanced exploratory process technology, and advanced fuels research: Volume 1 -- Base program. Final report, October 1986--September 1993

Energy Technology Data Exchange (ETDEWEB)

Smith, V.E.

1994-05-01

Numerous studies have been conducted in five principal areas: oil shale, tar sand, underground coal gasification, advanced process technology, and advanced fuels research. In subsequent years, underground coal gasification was broadened to be coal research, under which several research activities were conducted that related to coal processing. The most significant change occurred in 1989 when the agreement was redefined as a Base Program and a Jointly Sponsored Research Program (JSRP). Investigations were conducted under the Base Program to determine the physical and chemical properties of materials suitable for conversion to liquid and gaseous fuels, to test and evaluate processes and innovative concepts for such conversions, to monitor and determine environmental impacts related to development of commercial-sized operations, and to evaluate methods for mitigation of potential environmental impacts. This report is divided into two volumes: Volume 1 consists of 28 summaries that describe the principal research efforts conducted under the Base Program in five topic areas. Volume 2 describes tasks performed within the JSRP. Research conducted under this agreement has resulted in technology transfer of a variety of energy-related research information. A listing of related publications and presentations is given at the end of each research topic summary. More specific and detailed information is provided in the topical reports referenced in the related publications listings.

Lance for injecting highly-loaded coal slurries into the blast furnace

Energy Technology Data Exchange (ETDEWEB)

Illuminati, D.

1991-10-29

A lance is used to inject fuel oil into a blast furnace. This simple design permits conversion of coal water and coal tar slurries to a fine mist at very low flow rates. This design prevents the build-up of deposits which increases service life and steadies the flow rate.

Reducing Heavy Metal Element from Coal Bottom Ash by Using Citric Acid Leaching Treatment

Directory of Open Access Journals (Sweden)

Yahya Ahmad Asyari

2017-01-01

Full Text Available Coal ash is the residue that is produced during coal combustion for instance fly ash, bottom ash or boiler slag which was primarily produced from the combustion of coal. With growth in coal burning power station, huge amount of coal bottom ash (CBA considered as hazardous material which are normally disposed in an on-site disposal system without any commercialization purpose. Previous researchers have studied the extraction of silica from agricultural wastes such as palm ash and rice husk ash (RHA and CBA by using leaching treatment method. In this study, the weaker acid, citric acid solution was used to replace the strong acid in leaching treatment process. Result showed that the heavy metal content such as Copper (Cu, Zinc (Zn and Lead (Pb can be decrease. Meanwhile the silica can be extracted up to 44% from coal bottom ash using citric acid leaching treatment under the optimum reaction time of 60 minutes with solution temperature of 60°C and concentration of citric acid more than 2%.

Rational use of coal from the Kansk-Achinsk basin

Energy Technology Data Exchange (ETDEWEB)

Andreeva, I.A.; Antonova, L.I.; Khapaeva, O.K.

1983-02-01

Brown coal from the Kansk-Achinsk basin will be used as fuel in power plants as well as raw material for production of coke and smokeless fuel. Production of semicoke should amount to 9 Mt/year, 4 Mt of which will be smokeless fuel. A method for coking brown coal from the Kansk-Achinsk basin developed by the MGI Institute is described: semicoke mixed with coal tar used as a binder and polymers (from 2 to 4%), playing the role of a modifier, is carbonized at 850 to 900 C. Briquets produced from brown coal semicoke are characterized by a high carbon content up to 94.7%, emission of volatile matter down to 9.0%, ash content of 8.8% and good mechanical properties. A method for production of coke for removal of sulfurous anhydride from coal power plant emission is described: semicoke is granulated using the heavy fraction of coal tar formed during semicoking, granules are carbonized and activated at a temperature of 900 C. Volume of mesopores and micropores in coke amounts to 0.4 cm/sup 3//g and the specific surface is 28 to 600 m/sup 2//g (with a combustion loss of of 20 to 24 %). This sorbent is also used as carrier for catalysts in metallurgy and for collecting and recovering solvents from industrial gases.

Process of treating tars

Energy Technology Data Exchange (ETDEWEB)

Hansen, C; Hempel, H; Weissenburger, H

1955-05-05

A process is described for treating tars or tar oils, especially carbonization tars, characterized in that the tars or tar oils are mixed with benzene or light oils which contain no aromatic material or only slight amounts, or with gas oil in such amounts that the asphalt precipitates, and after separation of the precipitated material the mixture is treated with caustic solution for separation of the phenols, and after separation of the phenolate liquor the mixture is subjected to heating for removal of the dilution medium, then the remaining oil can be used as heating oil or it is submitted to distillation for the purpose of recovering a fuel suitable for diesel motors, while the phenolate liquor is worked up into phenols.

Desulfurization and denitrogenation in copyrolysis of coal with hydrogen-rich gases

Energy Technology Data Exchange (ETDEWEB)

Liao, H.; Li, B.; Zhang, B. [Chinese Academy of Sciences, Taiyuan (China). Institute of Coal Chemistry

1999-06-01

Desulfurization and denitrogenation were systematically investigated by analyzing the chars and tars from copyrolysis of Yanzhou high sulfur bituminous coal with coke-oven gas (COG), synthesis gas (SG) and hydrogen. The results indicated that under the conditions of 3MPa, up to 650{degree}C with a heating rate of 10{degree}C/min, the desulfurization of coal pyrolysis with COG, SG and hydrogen were almost equal (about 80%, w%, ad), the order of denitrogenation were: hydrogen (41%) {gt} SG(35%) {gt} COG(30%). The distributions of sulfur in char, oil and gas was very similar under the three reactive gases, i.e., about 205 in char, 105 in tar and 70% (diff.) in gas, respectively. Compared with hydropyrolysis at the same hydrogen partial pressure, the desulfurization of coal pyrolysis with coke oven gas was increased by about 4.5%, while the denitrogenation was decreased by about 3.5%. There is an important desulfurization advantage for hydropyrolysis using COG and SG instead of pure hydrogen. Compared with the copyrolysis of coal with COG, Yanzhou coal pyrolysis under SG can achieve the same level of desufurization but higher denitrogenation. 11 refs., 3 figs., 4 tabs.

Degradation of polycyclic aromatic hydrocarbons (PAHs) in an aged coal tar contaminated soil under in-vessel composting conditions

International Nuclear Information System (INIS)

Antizar-Ladislao, Blanca; Lopez-Real, Joe; Beck, Angus James

2006-01-01

In-vessel composting of polycyclic aromatic hydrocarbons (PAHs) present in contaminated soil from a manufactured gas plant site was investigated over 98 days using laboratory-scale in-vessel composting reactors. The composting reactors were operated at 18 different operational conditions using a 3-factor factorial design with three temperatures (T, 38 deg. C, 55 deg. C and 70 deg. C), four soil to green waste ratios (S:GW, 0.6:1, 0.7:1, 0.8:1 and 0.9:1 on a dry weight basis) and three moisture contents (MC, 40%, 60% and 80%). PAH losses followed first order kinetics reaching 0.015 day -1 at optimal operational conditions. A factor analysis of the 18 different operational conditions under investigation indicated that the optimal operational conditions for degradation of PAHs occurred at MC 60%, S:GW 0.8:1 and T 38 deg. C. Thus, it is recommended to maintain operational conditions during in-vessel composting of PAH-solid waste close to these values. - Maximum degradation of PAHs in an aged coal tar contaminated soil can be achieved using optimal operational conditions during composting

ZnO template strategy for the synthesis of 3D interconnected graphene nanocapsules from coal tar pitch as supercapacitor electrode materials

Science.gov (United States)

He, Xiaojun; Li, Xiaojing; Ma, Hao; Han, Jiufeng; Zhang, Hao; Yu, Chang; Xiao, Nan; Qiu, Jieshan

2017-02-01

3D interconnected graphene nanocapsules (GNCs) were prepared from diverse aromatic hydrocarbons by a nano-ZnO-template strategy coupled with in-situ KOH activation technique. The as-made graphene networks feature thin carbonaceous shells with well-balanced micropores and mesopores. Such 3D porous networks provide freeways for good electron conduction, short pores for ion fast transport, and abundant micropores for ion adsorption. As the electrodes in supercapacitors, the unique 3D GNCs show a high capacitance of 277 F g-1 at 0.05 A g-1, a good rate performance of 194 F g-1 at 20 A g-1, and an excellent cycle stability with over 97.4% capacitance retention after 15000 cycles in 6 M KOH electrolyte. This synthesis strategy paves a universal way for mass production of 3D graphene materials from diverse aromatic hydrocarbon sources including coal tar pitch and petroleum pitch for high performance supercapacitors as well as support and sorbent.

Production of gas and volatile materials by distillation of tars, etc

Energy Technology Data Exchange (ETDEWEB)

Arson, M

1860-04-25

The principle of this production is in the treating of heavy oils with heat, their transformation occurring nearly completely by the action of this agent. The apparatus used consists of a retort of such a form that it has openings at the two ends immediately opposed to each other. One serves to introduce the oil and the other to remove the tar and gas produced. At the exit of the apparatus the gas passes into coolers like those used for coal gas.

Deciphering structure-activity relationships in a series of Tat/TAR inhibitors.

Science.gov (United States)

Pascale, Lise; González, Alejandro López; Di Giorgio, Audrey; Gaysinski, Marc; Teixido Closa, Jordi; Tejedor, Roger Estrada; Azoulay, Stéphane; Patino, Nadia

2016-11-01

A series of pentameric "Polyamide Amino Acids" (PAAs) compounds derived from the same trimeric precursor have been synthesized and investigated as HIV TAR RNA ligands, in the absence and in the presence of a Tat fragment. All PAAs bind TAR with similar sub-micromolar affinities but their ability to compete efficiently with the Tat fragment strongly differs, IC50 ranging from 35 nM to >2 μM. While NMR and CD studies reveal that all PAA interact with TAR at the same site and induce globally the same RNA conformational change upon binding, a comparative thermodynamic study of PAA/TAR equilibria highlights distinct TAR binding modes for Tat competitor and non-competitor PAAs. This led us to suggest two distinct interaction modes that have been further validated by molecular modeling studies. While the binding of Tat competitor PAAs induces a contraction at the TAR bulge region, the binding of non-competitor ones widens it. This could account for the distinct PAA ability to compete with Tat fragment. Our work illustrates how comparative thermodynamic studies of a series of RNA ligands of same chemical family are of value for understanding their binding modes and for rationalizing structure-activity relationships.

Removing tar information from cigarette packages may reduce South Korean smokers' misconceptions about low-tar cigarettes

Directory of Open Access Journals (Sweden)

Hye-Jin Paek

2018-03-01

Full Text Available Background Many smokers still have misconceptions about “light” or “low tar” cigarettes. In South Korea, low-tar (< 3 mg cigarette sales have increased sharply from 1.8% in 2002 to 49.2% in 2015. Although government regulations forbid cigarette packages from displaying messages such as “mild,” “low-tar,” and “light,” numbers indicating tar amounts are still permitted. This study examines whether removing tar information from packaging altogether reduces people's misconceptions about low tar cigarettes. Methods An online experiment was conducted among 531 smokers who were randomly assigned to one of two conditions. In the “tar” condition, 271 participants were shown in random order three cigarette packages for three major brands (Esse, The One, Marlboro with different tar amounts. In the “no-tar” condition, 260 participants were shown the same packages without tar information. Next, participants evaluated which type of cigarette was mildest, least harmful, easier for nonsmokers to start smoking, and easier for smokers to quit. After descriptive statistics were checked, twelve sets of chi-square tests were performed. Results Average age of the participants was 26.22 (14 - 62 years; 53.5% were male. All 12 chi-square tests were statistically significant. Participants in the tar condition judged the lowest-tar cigarette to be mildest, least harmful, easier to start, and easier to quit. In the no-tar condition, for the Korean brands Esse and The One, most respondents evaluated all cigarette types to be the same only for harm, ease of starting, and ease of quitting; for Marlboro, judgments were the same as those in the tar condition except that “easier to quit” was judged to be the same across the three types. Conclusions Banning tar information from cigarette packages may help reduce smokers' misconceptions about low-tar cigarettes. People have inconsistent judgments about differently packaged cigarettes when tar

Acidic surface functional groups and mineral elements in Lakra coal (Sindh, Pakistan)

International Nuclear Information System (INIS)

Saeed, K.; Ishaq, M.; Ahjmad, I.; Shakirullah, M.; Haider, S.

2010-01-01

Surface acidity of virgin coal (Lakra Sindh, Pakistan) and variously extracted/leached coal samples with HNO/sub 3/ NaOH, and KMnO/sub 4/, were investigated by aqueous potentiometric titration employing KOH as a titrant. The titration curve of virgin coal showed that its surface might contain carboxylic, carbonyl, phenolic and other weak acidic functional groups such as enols and C-H bond. The titration curves of leached coal samples showed inflections at pH 4-11, being not similar the inflections of carboxylic groups. This inflection might be given by functional groups like CO/sub 2/, phenolic, enols and C-H. Mineral matter such as Fe, K, Zn, Mn and Ni were determined in the ash of coal by atomic absorption spectrophotometer and was found that Fe (3104 micro g/g) in the highest and Ni (36.05 micro g/g) in the lowest quantity is present in virgin coal sample. (author)

Combustion and emissions characterization of pelletized coal fuels. Technical report, December 1, 1992--February 28, 1993

Energy Technology Data Exchange (ETDEWEB)

Rajan, S. [Southern Illinois Univ., Carbondale, IL (United States). Dept. of Mechanical Engineering and Energy Processes

1993-05-01

The aim of this project is to demonstrate that sorbent-containing coal pellets made from low grade coal or coal wastes are viable clean burning fuels, and to compare their performance with that of standard run-of-mine coal. Fuels to be investigated are: (a) carbonated pellets containing calcium hydroxide sorbent, (b) coal fines-limestone pellets with cornstarch as binder, (c) pellets made from preparation plant recovered coal containing limestone sorbent and gasification tar as binder, and (d) a standard run-of-mine Illinois seam coal. The fuels will be tested in a laboratory scale 411 diameter circulating fluidized bed combustor. Progress this quarter has centered on the development of a hydraulic press based pellet mill capable of the high compaction pressures necessary to produce the gasification tar containing pellets outlined in (c) above. Limited quantities of the pellets have been made, and the process is being fine tuned before proceeding into the production mode. Tests show that the moisture content of the coal is an important parameter that needs to be fixed within narrow limits for a given coal and binder combination to produce acceptable pellets. Combustion tests with these pellet fuels and the standard coal are scheduled for the next quarter.

Process to improve combustion and coalescing characteristics of coal pellets

Energy Technology Data Exchange (ETDEWEB)

Ban, T.E.; Marlowe, W.H.

1980-10-23

Baking types of coal, which occur mainly in the Midwestern States of the USA, tend to form solid layers when heated to remove tar. In order to prevent this, it is proposed to pulverize the coal, to form small pellets and to coat these pellets. A suitable coating material mentioned here is sodium carbonate. Variants of the coating process are given. The coated pellets are heated.

Characterization of desulfurization, denitrogenation and process sulfur transfer during hydropyrolysis of Chinese high sulfur coals

Energy Technology Data Exchange (ETDEWEB)

Sun Chenggong; Li Baoqing [Chinese Academy of Sciences, Taiyuan (China). State Key Lab. of Coal Conversion; Snape, C.E. [Strathclyde Univ., Glasgow (United Kingdom). Dept. of Pure and Applied Chemistry

1997-12-31

The process desulphurization and denitrogenation of Chinese high sulfur coals and the characteristics of sulfur transformation during non-catalytic hydropyrolysis were investigated by a 10 g fixed-bed reactor and a small-scaled reactor with online spectrometry respectively. It was indicated that more than 70% of the total sulfur of the two high sulfur coals and almost all pyritic sulfur are removed as H{sub 2}S, leaving the char and tar products with much less sulfur distribution. The liability of sulfur transformation to tar products is closely related to the thiophenic structure forms rather than sulfidic forms. At the same time, the formation of trace amount of sulfur dioxide indicates the presence of inherent sulfur oxidation reactions inside coal frame structures even under H{sub 2} pressure. (orig.)

Development of clean coal and clean soil technologies using advanced agglomeration techniques

International Nuclear Information System (INIS)

Ignasiak, B.; Ignasiak, T.; Szymocha, K.

1990-01-01

Three major topics are discussed in this report: (1) Upgrading of Low Rank Coals by the Agflotherm Process. Test data, procedures, equipment, etc., are described for co-upgrading of subbituminous coals and heavy oil; (2) Upgrading of Bituminous Coals by the Agflotherm Process. Experimental procedures and data, bench and pilot scale equipments, etc., for beneficiating bituminous coals are described; (3) Soil Clean-up and Hydrocarbon Waste Treatment Process. Batch and pilot plant tests are described for soil contaminated by tar refuse from manufactured gas plant sites. (VC)

Response of microbial activities and diversity to PAHs contamination at coal tar contaminated land

Science.gov (United States)

Zhao, Xiaohui; Sun, Yujiao; Ding, Aizhong; Zhang, Dan; Zhang, Dayi

2015-04-01

Coal tar is one of the most hazardous and concerned organic pollutants and the main hazards are polycyclic aromatic hydrocarbons (PAHs). The indigenous microorganisms in soils are capable to degrade PAHs, with essential roles in biochemical process for PAHs natural attenuation. This study investigated 48 soil samples (from 8 depths of 6 boreholes) in Beijing coking and chemistry plant (China) and revealed the correlation between PAHs contamination, soil enzyme activities and microbial community structure, by 16S rRNA denaturing gradient gel electrophoresis (DGGE). At the site, the key contaminants were identified as naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene and anthracene, and the total PAHs concentration ranged from 0.1 to 923.9 mg/kg dry soil. The total PAHs contamination level was positively correlated (pcatalase activities (0.554-6.230 mL 0.02 M KMnO4/g•h) and dehydrogenase activities (1.9-30.4 TF μg/g•h soil), showing the significant response of microbial population and degrading functions to the organic contamination in soils. The PAHs contamination stimulated the PAHs degrading microbes and promoted their biochemical roles in situ. The positive relationship between bacteria count and dehydrogenase activities (p<0.05) suggested the dominancy of PAHs degrading bacteria in the microbial community. More interestingly, the microbial community deterioration was uncovered via the decline of microbial biodiversity (richness from 16S rRNA DGGE) against total PAHs concentration (p<0.05). Our research described the spatial profiles of PAHs contamination and soil microbial functions at the PAHs heavily contaminated sites, offering deeper understanding on the roles of indigenous microbial community in natural attenuation process.

Technology unlocks tar sands energy

Energy Technology Data Exchange (ETDEWEB)

Law, C

1967-09-25

Tar sand processing technology has been developed primarily in the categories of extraction techniques and in-situ processing. In October, a $235 million venture into tar sand processing will be inspected by visitors from many points on the globe. A synthetic crude of premium quality will be flowing through a 16-in. pipeline from the Tar Island plant site of Great Canadian Oil Sands to Edmonton. This processing plant uses an extractive mining technique. The tar sand pay zone in this area averages approximately 150 ft in thickness with a 50-ft overburden. It has been estimated that the tar sands cannot be exploited when the formation thickness is less than 100 ft and overburden exceeds the same amount. This indicates that extraction techniques can only be used to recover approximately 15% of the tar sand deposits. An in-situ recovery technique developed by Shell of Canada is discussed in detail. In essence it is selective hydraulic fracturing, followed by the injection of emulsifying chemicals and steam.

The potential of the essential fatty acid-deficient hairless rat as a psoriasis screening model for topical anti-proliferative drugs

DEFF Research Database (Denmark)

Jensen, Mette; Groth, L.; Holmer, G.

2002-01-01

were fed with a fat-free diet lacking linoleic acid. The EFAD condition was established within 8 weeks. In order to ensure that this condition had been established, several parameters were measured and observed, i.e. animal weight, water consumption, transepidermal water loss, clinical skin symptoms...... with calcipotriol. Dithranol and its coal tar-containing vehicle also showed a reductive effect on epidermal thickness. EFAD hairless rats possess various histological changes resembling psoriasis. These histological changes normalise during treatment with anti-psoriatic drugs as calcipotriol, dithranol and coal...

Coal Technology Program progress report for April 1976

Energy Technology Data Exchange (ETDEWEB)

1976-06-01

In the Hydrocarbonization Research program, two successful experiments were completed in the bench-scale hydrocarbonizer. A settling test at a lower temperature (390/sup 0/F) using 20 percent toluene in Solvent Refined Coal (SRC) Unfiltered Oil (UFO) produced a 30 percent clarified product in 2 hr. Characterization tests include distillation curves for Wilsonville's SRC-UFO and a particle size distribution of Pittsburg and Midway Coal Mining Company's (PAMCO) SRC-UFO. Studies of intermediate-temperature pyrolysis of large blocks have been maintained with char samples continuing to demonstrate pyrophoricity, even after heating to 700/sup 0/C. Simulated distillation analysis of tars produced by the last eight experiments are being compared with those performed at Laramie upon tars produced by the Hanna No. 2 experiment. In Coal-Fueled MIUS, stainless steel tubing to be used in one of the furnace tube bundles was ordered and the bid package for the furnace completed. Tests continued on the coal feed system and with the cold flow fluidized bed model. For the Synthoil process, flow diagrams, material balances, and utilities requirements were completed for the entire facility. For the Hydrocarbonization process, flowsheets were reviewed for compatibility; equipment lists were brought up to date; and utilities requirements were compiled from the individual flowsheets. The char recovery and storage subsystem flowsheet was completed. (auth)

Dynamic measurement of coal thermal properties and elemental composition of volatile matter during coal pyrolysis

Directory of Open Access Journals (Sweden)

Rohan Stanger

2014-01-01

Full Text Available A new technique that allows dynamic measurement of thermal properties, expansion and the elemental chemistry of the volatile matter being evolved as coal is pyrolysed is described. The thermal and other properties are measured dynamically as a function of temperature of the coal without the need for equilibration at temperature. In particular, the technique allows for continuous elemental characterisation of tars as they are evolved during pyrolysis and afterwards as a function of boiling point. The technique is demonstrated by measuring the properties of maceral concentrates from a coal. The variation in heats of reaction, thermal conductivity and expansion as a function of maceral composition is described. Combined with the elemental analysis, the results aid in the interpretation of the chemical processes contributing to the physical and thermal behaviour of the coal during pyrolysis. Potential applications in cokemaking studies are discussed.

Silicon carbide modified carbon materials. Formation of nanocrystalline SiC from thermochemical processes in the system coal tar pitch/poly(carbosilane)

Energy Technology Data Exchange (ETDEWEB)

Czosnek, C.; Janik, J.F.; Olejniczak, Z. [Stanislaw Staszic University of Mining & Meterology, AGH, Krakow (Poland)

2002-12-01

Poly(carbosilane) or PCS, (-CH{sub 2}-SiH(CH{sub 3})-){sub n}, is used as a Si-bearing precursor in combination with a coal tar pitch to study thermally induced transformations toward SiC-modified carbon composites. Following mixing of the components in the molten pitch at 160{sup o}C, the mixture is heated under argon atmosphere at 500{sup o}C yielding a solid carbonizate that is further subjected to separate pyrolysis experiments at 1300{sup o}C or 1650{sup o}C. At temperatures up to 500{sup o}C, the PCS reacts with suitable pitch components as well as undergoing decomposition reactions. At higher temperatures, clusters of prevailingly nanocrystalline beta-SiC are confirmed after the 1650{sup o}C pyrolysis step with indications that the formation of the compound starts at 1300{sup o}C. Si-29 MAS NMR, XRD, FT-IR, XPS, and elemental analysis are used to characterize each pyrolysis step, especially, from the viewpoint of transformation of silicon species to silicon carbide in the carbon matrix evolved from the pitch.

Environmental geochemistry of acid mine drainage water at Indus coal mine at Lakhra, Sindh Pakistan

International Nuclear Information System (INIS)

Siddique, I.; Shah, M.T.

2000-01-01

The annual coal production of Pakistan is about 3,637, 825 tones which is about 6% of the country's energy resources, out of this 1,241, 965 tones of coal was produced/ mined from the Lakhra coal field, District Dadu, Sindh which after the Thar coal field is the second largest coal field of Pakistan. At this coal field more than 58 mining companies are engaged in exploring the hidden wealth of the country. The problem of acid mine drainage, is caused by the passage or seepage of water, through mines where iron disulfides, usually pyrites, are exposed to the oxidizing action of water, air and bacteria, is the main problem faced by the mining companies. The geochemical analysis of acid mine drainage water collected from Indus coal mine no. 6 shows that beside its higher pH, total Dissolved Solids and Sulfates, it also posses higher amount of heavy metals like Cd, Cu, Pb, Co, Ni and Fe. This acid mine drainage water not only damages the mine structures but is also harmful to soil and ecology. (author)

The Charfuel coal refining process

International Nuclear Information System (INIS)

Meyer, L.G.

1991-01-01

The patented Charfuel coal refining process employs fluidized hydrocracking to produce char and liquid products from virtually all types of volatile-containing coals, including low rank coal and lignite. It is not gasification or liquefaction which require the addition of expensive oxygen or hydrogen or the use of extreme heat or pressure. It is not the German pyrolysis process that merely 'cooks' the coal, producing coke and tar-like liquids. Rather, the Charfuel coal refining process involves thermal hydrocracking which results in the rearrangement of hydrogen within the coal molecule to produce a slate of co-products. In the Charfuel process, pulverized coal is rapidly heated in a reducing atmosphere in the presence of internally generated process hydrogen. This hydrogen rearrangement allows refinement of various ranks of coals to produce a pipeline transportable, slurry-type, environmentally clean boiler fuel and a slate of value-added traditional fuel and chemical feedstock co-products. Using coal and oxygen as the only feedstocks, the Charfuel hydrocracking technology economically removes much of the fuel nitrogen, sulfur, and potential air toxics (such as chlorine, mercury, beryllium, etc.) from the coal, resulting in a high heating value, clean burning fuel which can increase power plant efficiency while reducing operating costs. The paper describes the process, its thermal efficiency, its use in power plants, its pipeline transport, co-products, environmental and energy benefits, and economics

On the reaction of some bacteria and fungi on coal tar creosote. Zur Verhalten einiger Bakterien und Pilze gegenueber Steinkohlenteeroel

Energy Technology Data Exchange (ETDEWEB)

Schmidt, O.; Dittberner, D.; Faix, O. (Universitaet Hamburg, Hamburg (Germany). Ordinariat fuer Holzbiologie)

1991-01-01

To contribute to the waste management of wood preservatives, the biodegradability of coal tar creosote by bacteria and fungi has been investigated. Microorganisms comprised 24 bacterial strains and 31 fungi from different systematic and ecological groups as well as isolates from contaminated soils. Based on countings of viable cells, the experiments with various nutrient media, methods of cultivation, preservative concentrations, and organic solvents yielded some bacteria which could grow in the presence of creosote: {ital Aeromonas hydrophila}, {ital Flavobacterium} sp., {ital Pseudomonas arvilla}, {ital P. fluorescens}, and {ital P. putida}. The white-rot fungi {ital Bjerkandera adusta}, {ital Heterobasidion annosum}, {ital Hirschioporus abietinus}, {ital Lentinula edodes}, {ital Peniophora gigantea}, {ital Pleurotus ostreatus}, {ital Schizophyllum commune}, and {ital Trametes versicolor}, the brown-rot fungus {ital Lentinus lepideus}, the staining fungi {ital Ceratocystis piceae} and {ital Stereum sanguinolentum}, and the moulds {ital Paecilomyces variotii} and {ital Trichoderma viride} also grew with creosote. To prepare samples for IR-measurements, continuous extraction of creosote from the nutrient liquid by percolation with methylene chloride was suitable. However, the IR-spectra of creosote did not show any measurable changes after incubation with 16 bacterial strains and 6 fungi. 42 refs., 2 figs., 4 tabs.

Analysis of tars produced in biomass gasification

Energy Technology Data Exchange (ETDEWEB)

Zhou, J.; Wang, Y.; Kinoshita, C.M. [Univ. of Hawaii, Honolulu, HI (United States)

1993-12-31

Parametric tests on tar formation, varying temperature, equivalence ratio, and residence time, are performed on a bench-scale, indirectly-heated fluidized bed gasifier. Prepared tar samples are analyzed in a gas chromatograph (GC) with a flame ionization detector, using a capillary column. Standards containing dominant tar species have been prepared for GC calibration. The identified peaks include single-ring hydrocarbons, such as benzene, to five-ring hydrocarbons, such as perylene; depending on the gasification conditions, the identified species represent about 70 to 90% (mass basis) of the tar constituents. Under all conditions tested, benzene and naphthalene were the most dominant species. Temperature and equivalence ratio have significant effect on tar yield and tar composition. Tar yield decreases with increasing temperature or equivalence ratio. The test results suggest that lower temperature favors the formation of more aromatic tar species with diversified substituent groups, while higher temperature favors the formation of fewer aromatic tar species without substituent groups. Higher temperature or equivalence ratio favors the formation of polyaromatic compounds. Oxygen-containing compounds exist in significant quantities only at temperature below 800{degrees}C and decrease with increasing temperature, equivalence ratio, or residence time.

The extraction of bitumen from western tar sands. Annual report, July 1990--July 1991

Energy Technology Data Exchange (ETDEWEB)

Oblad, A.G.; Bunger, J.W.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

1992-04-01

Contents of this report include the following: executive summary; characterization of the native bitumen from the Whiterocks oil sand deposit; influence of carboxylic acid content on bitumen viscosity; water based oil sand separation technology; extraction of bitumen from western oil sands by an energy-efficient thermal method; large- diameter fluidized bed reactor studies; rotary kiln pyrolysis of oil sand; catalytic upgrading of bitumen and bitumen derived liquids; ebullieted bed hydrotreating and hydrocracking; super critical fluid extraction; bitumen upgrading; 232 references; Appendix A--Whiterocks tar sand deposit bibliography; Appendix B--Asphalt Ridge tar sand deposit bibliography; and Appendix C--University of Utah tar sands bibliography.

The bonding of heavy metals on nitric acid-etched coal fly ashes functionalized with 2-mercaptoethanol or thioglycolic acid

International Nuclear Information System (INIS)

Muñoz, M.I.; Aller, A.J.; Littlejohn, D.

2014-01-01

Coal fly ash is a waste by-product of the coal fire industry, which generates many environmental problems. Alternative uses of this material would provide efficient solutions for this by-product. In this work, nitric acid-etched coal fly ash labelled with 2-mercaptoethanol or thioglycolic acid was assessed for retention of Al(III), As(III), Cu(II), Cd(II), Fe(III), Mn(II), Hg(II), Ni(II), Pb(II) and Zn(II) ions. The bonding characteristics between the organic compounds with the solid support, as well as with the metal ions, were evaluated using various surface analytical techniques. Visualization of the organically-functionalized coal fly ash particle was possible using scanning electron microscopy (SEM), while the elemental composition of the functionalized material, before and after retention of the metal ions, was obtained by energy dispersive (ED)-X ray spectrometry (XRS) and electrothermal atomic absorption spectrometry (ETAAS). Fourier transform infrared (FT-IR) spectrometry and Raman spectrometry were used to obtain information about the functional groups. It was found that some metal(oid) ions (As, Ni, Pb, Zn) were coordinated through the mercaptan group, while other metal(oid)s (Al, Cd, Cu, Fe, Hg, Mn) were apparently bonded to oxygen atoms. A low-cost and effective solid phase retention system for extraction of heavy metals from aqueous solutions was thus developed. - Graphical abstract: Nitric acid-etched coal fly ash labelled with 2-mercaptoethanol or thioglycolic acid was intended for the retention of heavy metals. The bonding characteristics between the organic compounds with the solid support, as well as with the metal ions, were evaluated using surface analytical techniques. - Highlights: • Coal fly ashes were organically-functionalized. • Organically-functionalized coal fly ashes were spectrometrically characterized. • Organically-functionalized coal fly ashes can be used as an effective solid sorbent for metal(oid)s. • This retention

Hydrothermal pretreatment of coal. Quarterly report No. 1, September 21--December 15, 1989

Energy Technology Data Exchange (ETDEWEB)

Ross, D.S.

1989-12-21

We have examined changes in Argonne Premium samples of Wyodak coal following 30 min treatment in liquid water at autogenous pressures at 150{degrees}, 250{degrees}, and 350{degrees}C. In most runs the coal was initially dried at 60{degrees}C/1 torr/20 hr. The changes were monitored by pyrolysis field ionization mass spectrometry (py-FIMS) operating at 2.5{degrees}C/min from ambient to 500{degrees}C. We recorded the volatility patterns of the coal tars evolved over that temperature range, and in all cases the tar yields were 25%--30% of the starting coal on mass basis. There was essentially no change after the 150{degrees}C treatment. Small increases in volatility were seen following the 250{degrees}C treatment, but major effects were seen in the 350{degrees} work. The tar quantity remained unchanged; however, the volatility increased so the temperature of half volatility for the as-received coal of 400{degrees}C was reduced to 340{degrees}C. Control runs with no water showed some thermal effect, but the net effect from the presence of liquid water was clearly evident. The composition was unchanged after the 150{degrees} and 250{degrees}C treatments, but the 350{degrees} treatment brought about a 30% loss of oxygen. The change corresponded to loss of the elements of water, although loss of ``OH`` seemed to fit the analysis data somewhat better. The water loss takes place both in the presence and in the absence of added water, but it is noteworthy that the loss in the hydrothermal runs occurs at p(H{sub 2}O) = 160 atm. We conclude that the process must involve the dehydration solely of chemically bound elements of water, the dehydration of catechol is a specific, likely candidate.

Light-oil recovery in the low-temperature carbonization of brown coal

Energy Technology Data Exchange (ETDEWEB)

Jahn, A

1944-01-01

The various methods used for low-temperature carbonization of brown coal are reviewed as well as the effect of the method of carbonization on the properties and yields of light oil and tar. The composition of the light oil varied considerably with the coal and the method used. Light oil from the low-temperature distillation of brown coal contains relatively high contents of unsaturated hydrocarbons and variable content of phenols and S compounds, depending on the coal. Light oil is best recovered from low-temperature-carbonization gas by oil scrubbing; the use of active C would require preliminary removal of S compounds, which would be quite expensive.

Gasification of high ash, high ash fusion temperature bituminous coals

Science.gov (United States)

Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

2015-11-13

This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

Bed retained products in swept fixed bed (SFB) coal hydropyrolysis

Energy Technology Data Exchange (ETDEWEB)

Mastral, A.M.; Perez-Surio, M.J. [CSIC, Zaragosa (Spain). Inst. de Carboquimica

1997-12-31

The hydropyrolysis of a low rank coal in a swept fixed bed (SFB) reactor is carried out by fixing the hydrogen pressure (40 kg/cm{sup 2}), the hydrogen flow (2 l/min) and the residence time (10 min) at increasing temperatures (400 C, 500 C and 600 C) and coal bed heights (h, 1.5h, 2h, 2.5h and 3h). It is shown that the percentages of tars and char directly depend on the coal bed height and that there is not only a quantitative dependence, but also the height of the coal bed is very important and plays a relevant role on the nature of the conversion products. (orig.)

Briquetting and coking behavior of Bobov-Dol coal

Energy Technology Data Exchange (ETDEWEB)

Naundorf, W.

1987-01-01

Hard Bulgarian glance brown coal (23.2% ash content, 16% coal moisture 2.39% sulfur) was studied for its general suitability for partial black coal coke substitution in coking plants and for the possibility of producing pyrolysis briquets for coking purposes. Laboratory briquetting variants include coal briquetting without binders, with sulfite lye as binder, briquetting after partial demineralization by wet classification, briquetting of different screening fractions (0 to 4 mm), briquetting as a mixture with type 35 caking black coal as well as mixed with type 34 less caking black coal under addition of black coal tar, pitch or bitumen. Coking of the briquets produced was carried at with and without charge compacting. Graphs and tables provide briquetting and coking results. It is concluded that high strength coke can be produced from this brown coal, but it can only be used commercially as heating coke due to its high ash and sulfur content. Briquetting and coking of partially demineralized brown coal in a mixture with black coal and binders resulted in suitable metallurgical coke. Maximum percentage of brown coal in the briquetting mixture was 30%. 4 refs.

Thermocatalytical processing of coal and shales

Directory of Open Access Journals (Sweden)

Zhaksyntay Kairbekov

2012-12-01

Full Text Available The article investigates the questions of thermocatalytical conversion of organic mass of coal (OMC, it is shown that in the absence of a catalyst process is carried out by a radical process. Accumulated data on the properties for radicals of different structure and therefore different reaction capacity enables us to understand and interpret the conversion of OMC. Thermal conversion of OMC regarded as a kind of depolymerization, accompanied by decomposition of the functional groups with the formation of radicals, competing for hydrogen atom. Catalyst can change the direction and conditions of the process. Modern catalysts can reduce the process pressure up to 50 atm., with a high degree of coal conversion. We consider examples of simultaneous conversion of coal and shale, shale and masut, shale and tar.

Simulation of ground-water flow in the St. Peter aquifer in an area contaminated by coal-tar derivatives, St. Louis Park, Minnesota. Water Resources Investigation

International Nuclear Information System (INIS)

Lorenz, D.L.; Stark, J.R.

1990-01-01

A model constructed to simulate ground-water flow in part of the Prairie du Chien-Jordan and St. Peter aquifers, St. Louis Park, Minnesota, was used to test hypotheses about the movement of ground water contaminated with coal-tar derivatives and to simulate alternatives for reducing the downgradient movement of contamination in the St. Peter aquifer. The model, constructed for a previous study, was applied to simulate the effects of current ground-water withdrawals on the potentiometric surface of the St. Peter aquifer. Model simulations predict that the multiaquifer wells have the potential to limit downgradient migration of contaminants in the St. Peter aquifer caused by cones of depression created around the multiaquifer wells. Differences in vertical leakage to the St. Peter aquifer may exist in areas of bedrock valleys. Model simulations indicate that these differences are not likely to affect significantly the general patterns of ground-water flow

Development and start up of a co-injection system of coal tar/natural gas in blast furnace no. 4; Desarrollo y puesta en operacion de un sistema de co-inyeccion de alquitran/gas natural en el alto horno no. 4

Energy Technology Data Exchange (ETDEWEB)

Falcon Rodriguez, Manuel I; Mata Esparza, Hector Rolando; Arevalo Ballesteros, Gerardo [Altos Hornos de Mexico S. A., Coahuila (Mexico)

1994-12-31

The crisis has attracted the world`s attention on the need for energy conservation and the development in a greater extent the utilization of carbon base fuels and other energy sources (nuclear energy). Being a blast furnace, not only an energy consumer but also an energy producer, the greatest contribution to the pig iron cost is the energy needed to melt and reduce to metallic state the iron ores, this energy is mainly derived from coke. The dependence on coal via the coking plant to produce first fusion iron is incremented day after day as a result of the high levels of production. Altos Hornos de Mexico (AHMSA), contemplated within its strategic plan, the reduction in the production of its coking plants derived from the natural aging of its furnaces, consequently the shortage of coke for productions higher than 2.6 MMT of pig iron is pending. The injection of fuels into a blast furnace through its nozzles is a technology used for the diminishing the coke consumption of coke, its use implies a change in the philosophy of the blast furnace operation, and is currently employed in most of the blast furnaces of the world. AHMSA taking advantage of coal tar production (approx. 130 tons/day) in its coking plants decided the design and put into operation a co-injection system of coal tar and natural gas. The activities tending to carry out this project were initiated on April 1993, performing all of them with its own resources, completing them on July 18, 1993, day on which the injection of coal tar/natural gas in blast furnace No. 4 in a stable form. To date (October 1993), the coal tar injection has been increased up to 36 kg/ton of pig iron. During the injection periods, the presence of operational, mechanical and instrumentation problems have not been an obstacle for the evolution on the injection, fulfilling its function of substituting coke in a replacing relationship of 1:1, i.e. 1 kg of coal tar per each kg of coke, without affecting the product quality

Development and start up of a co-injection system of coal tar/natural gas in blast furnace no. 4; Desarrollo y puesta en operacion de un sistema de co-inyeccion de alquitran/gas natural en el alto horno no. 4

Energy Technology Data Exchange (ETDEWEB)

Falcon Rodriguez, Manuel I.; Mata Esparza, Hector Rolando; Arevalo Ballesteros, Gerardo [Altos Hornos de Mexico S. A., Coahuila (Mexico)

1993-12-31

The crisis has attracted the world`s attention on the need for energy conservation and the development in a greater extent the utilization of carbon base fuels and other energy sources (nuclear energy). Being a blast furnace, not only an energy consumer but also an energy producer, the greatest contribution to the pig iron cost is the energy needed to melt and reduce to metallic state the iron ores, this energy is mainly derived from coke. The dependence on coal via the coking plant to produce first fusion iron is incremented day after day as a result of the high levels of production. Altos Hornos de Mexico (AHMSA), contemplated within its strategic plan, the reduction in the production of its coking plants derived from the natural aging of its furnaces, consequently the shortage of coke for productions higher than 2.6 MMT of pig iron is pending. The injection of fuels into a blast furnace through its nozzles is a technology used for the diminishing the coke consumption of coke, its use implies a change in the philosophy of the blast furnace operation, and is currently employed in most of the blast furnaces of the world. AHMSA taking advantage of coal tar production (approx. 130 tons/day) in its coking plants decided the design and put into operation a co-injection system of coal tar and natural gas. The activities tending to carry out this project were initiated on April 1993, performing all of them with its own resources, completing them on July 18, 1993, day on which the injection of coal tar/natural gas in blast furnace No. 4 in a stable form. To date (October 1993), the coal tar injection has been increased up to 36 kg/ton of pig iron. During the injection periods, the presence of operational, mechanical and instrumentation problems have not been an obstacle for the evolution on the injection, fulfilling its function of substituting coke in a replacing relationship of 1:1, i.e. 1 kg of coal tar per each kg of coke, without affecting the product quality

Thermal stability of carboxylic acid functionality in coal; Sekitanchu ni sonzaisuru karubokishiruki no netsubunkai kyodo

Energy Technology Data Exchange (ETDEWEB)

Tsutsumi, Y.; Aida, T. [Kinki University, Osaka (Japan). Faculty of Engineering

1996-10-28

Carboxyl in coal was focused in discussing its pyrolytic behavior while tracking change of its absolute amount relative to the heating temperatures. A total of four kinds of coals, consisting of two kinds brown coals, sub-bituminous coal and bituminous coal were used. Change in the absolute amount of carboxyl due to heating varies with coalification degree. Decomposition starts in the bituminous coal from around 300{degree}C, and is rapidly accelerated when 400{degree}C is exceeded. Carboxyls in brown coals exist two to three times as much as those in bituminous and sub-bituminous coals, of which 40% is decomposed at a temperature as low as about 300{degree}C. Their pyrolytic behavior at temperatures higher than 400{degree}C resembles that of the bituminous coal. Carboxyls consist of those easy to decompose and difficult to decompose. Aromatic and aliphatic carboxylic acids with simple structure are stable at temperatures lower than 300{degree}C, and decompose abruptly from about 400{degree}C, hence their behavior resembles that of carboxyls in bituminous and sub-bituminous coals. Structure of low-temperature decomposing carboxyls in brown coals is not known, but it is assumed that humic acid originated from natural materials remains in the structure. 4 refs., 3 figs., 1 tab.

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tars, and oils containing powdered coal, coke, oreat, sulphur in suspension, by passing air or other oxygen-containing gas through a layer of the material of a depth sufficient substantially to deoxygenate the air and c., is carried out in stages in a series of treatment zones, the pressure in at least one of the zones being above atmospheric pressre. The products of oxidation include acetaldehyde, propionaldehyde, formic, acetic, propionic, butyric, acrylic and phthalic acids, alcohols, acetone, solvents, gums, and substances adapted for use as motor fuels or burnign oils. The oxidizing gas may be enriched with oxygen or be diluted with steam, and its point of entry into the oil and c. layer may be varied to promote or retard settlement of suspended solids.

Thermal behaviour during the pyrolysis of low rank perhydrous coals

Energy Technology Data Exchange (ETDEWEB)

Arenillas, A.; Rubiera, F.; Pis, J.J.; Cuesta, M.J.; Suarez-Ruiz, I. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain); Iglesias, M.J. [Area de Quimica Organica, Universidad de Almeria, Carretera de Sacramento, 04120 Almeria (Spain); Jimenez, A. [Area de Cristalografia y Mineralogia, Departamento de Geologia, Campus de Llamaquique, 33005 Oviedo (Spain)

2003-08-01

Perhydrous coals are characterised by high H/C atomic ratios and so their chemical structure is substantially modified with respect to that of conventional coals. As a result, perhydrous coals show different physico-chemical properties to common coals (i.e. higher volatile matter content, enhancement of oil/tar potential, relatively lower porosity and higher fluidity during carbonisation). However, there is little information about thermal behaviour during the pyrolysis of this type of coal. In this work, six perhydrous coals (H/C ratio between 0.83 and 1.07) were pyrolysed and analysed by simultaneous thermogravimetry/mass spectrometry. The results of this work have revealed the influence of high H/C values on the thermal behaviour of the coals studied. During pyrolysis the perhydrous coals exhibit very well defined, symmetrical peaks in the mass loss rate profiles, while normal coals usually show a broader peak. The shape of such curves suggests that in perhydrous coals fragmentation processes prevailed over condensation reactions. The high hydrogen content of perhydrous coals may stabilise the free radicals formed during heat treatment, increasing the production of light components.

Weathering behaviour of overburden-coal ash blending in relation to overburden management for acid mine drainage prevention in coal surface mine

International Nuclear Information System (INIS)

Gautama, R.S.; Kusuma, G.J.; Lestari, I.; Anggana, R.P.

2010-01-01

Potentially acid forming (PAF) materials are encapsulated with non-acid forming materials (NAF) in order to prevent acid mine drainage (AMD) in surface coal mines. NAF compaction techniques with fly and bottom ashes from coal-fired power plants are used in mines with limited amounts of NAF materials. This study investigated the weathering behaviour of blended overburden and coal combustion ash in laboratory conditions. Free draining column leach tests were conducted on different blending schemes. The weathering process was simulated by spraying the samples with de-ionized water once per day. The leachates were then analyzed using X-ray diffraction and fluorescence analyses in order to identify the mineral composition of the samples over a 14 week period. Results of the study indicated that the weathering process plays a significant role in controlling infiltration rates, and may increase the capability of capping materials to prevent infiltration into PAF materials. Fly- and bottom-ash additions improved the performance of the encapsulation materials. 3 refs., 4 tabs., 2 figs.

Electrochemistry of carbonaceous materials; 2. Anodic electroactivity of coal slurries in 85% phosphoric acid media

Energy Technology Data Exchange (ETDEWEB)

Tomat, R.; Salmaso, R.; Zecchin, S. (CNR-Instituto di Polarografia ed Elettrochimica Preparative, Padova (Italy))

1992-04-01

Current-potential curves of suspended coal (Sulcis basin, Sardinia, Italy) in 85% H{sub 3}PO{sub 4} were taken on a platinum electrode at 100{degree}C. Anodic current in the potential range of 0-1.5 V versus saturated calomel electrode was due to some humic acid-type substances released by coal in the electrolyte. The leaching of organic matter increased with the lowering of the particle dimensions, and the related oxidation currents attained stable values even during slurry formation. Current-potential curves were still unchanged when coal was filtered off from the suspension. Previous washing of ground coal with diluted mineral acids, including H{sub 3}PO{sub 4}, did not dissolve any significant amount of the substances responsible for the electrochemical activity of the coal sample examined. 14 refs., 6 figs.

Thermal remediation of tar-contaminated soil and oil-contaminated gravel

International Nuclear Information System (INIS)

Anthony, E.J.; Wang, J.

2005-01-01

High temperature treatments are commonly considered for the decontamination of soil as they have the advantages of reliability, high capacity, and effective destruction of hazardous materials with reduced long-term liability. This paper examined the remediation of soil contaminated by coal tar as well as gravel contaminated by oil. Pilot plant studies were conducted using 2 representative incineration technologies: rotary kiln and fluidized bed. The coal tar contaminated soil had accumulated over a few decades at a calcination plant in western Canada. The soil was sticky and could not be handled by conventional feeding and combustion systems. Crushed lignite was mixed with the soil as an auxiliary fuel and to reduce stickiness. A pilot plant furnace was used to evaluate the potential of decontamination in a rotary calciner. An analysis of both a modelling study and the test results showed that complete decontamination could be achieved in the targeted calciner. The results suggested that energy recovery was also possible, which could in turn make the remediation process more cost-effective. Decontamination of oil-contaminated gravel was conducted with a pilot plant fluidized bed combustor to study the feasibility of using incineration technology in the remediation of gravel and debris contaminated by oil spills. Results indicated that the gravel was decontaminated with acceptable emission performance. It was concluded that the study will be valuable to the application of commercial incineration processes for the remediation of polluted soils. It was observed that the weathering of the oiled gravel lowered the rate of decontamination. A small amount of salt water resulted in lowered decontamination rates, which may be an important factor for situations involving the remediation of shoreline gravel contaminated by oil. 24 refs., 6 tabs., 7 figs

Reactions of oxygen containing structures in coal pyrolysis

Energy Technology Data Exchange (ETDEWEB)

Hodek, W.; Kirschstein, J.; Van Heek, K.-H. (DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany, F.R.))

1991-03-01

In coal pyrolysis O-containing structures such as ether bridges and phenolic groups play an important role. Their reactions were studied by non-isothermal pyrolysis of a high volatile bituminous coal and some model polymers with gas chromatographic detection of the gaseous pyrolysis products. The coal was separated into the maceral groups vitrinite, exinite and inertinite, which showed markedly different pyrolysis behaviour. The formation of CO, methane and benzene was measured versus temperature. By comparison with polyphenyleneoxide and phenol-formaldehyde resins, it was found that the main volatilization, during which most of the tar is evolved, is initiated by cleavage of alkyl-aryl-ethers. Rearrangements of the primarily formed radicals lead to the formation of CO and methane at higher temperatures. 5 refs., 8 figs., 1 tab.

Process for carbonizing coal, shale, wood, etc

Energy Technology Data Exchange (ETDEWEB)

Matthaei, K

1924-05-08

A process for carbonization of coal, shale, and wood, for recovering low temperature tar and other products in a rotary retort is described. The material to be carbonized is brought directly in contact with the heating medium, that is characterized in that the heating medium streams through the retort crosswise to the longitudinal axis. The temperature of this medium in the single retort segments can be regulated.

Soil amendments promote vegetation establishment and control acidity in coal combustion waste

Science.gov (United States)

R.M. Danker; D.C. Adriano; Bon-Jun Koo; C.D. Barton

2003-01-01

The effects of adding various soil amendments and a pyrite oxidation inhibitor to aid in the establishment of vegetation and to reduce acid drainage (AD) from coal fly ash and coal reject (FA + CR*) were assessed in an outdoor mesocosm study. Preliminary greenhouse experiments and field observations at the U.S. Department of Energy's Savannah River Site (SRS)...

Volatilisation of aromatic hydrocarbons from soil: part II, fluxes from coal tar contaminated soils residing below the soil surface

International Nuclear Information System (INIS)

Lindhardt, B.; Christensen, T.H.

1996-01-01

The non-steady-state fluxes of aromatic hydrocarbons from coal tar contaminated soil, placed below a 5 cm deep layer of uncontaminated soil, were measured in the laboratory over a period of 53 days. The contaminated soil originated from a former gasworks site and contained concentrations of 11 selected aromatic hydrocarbons between 50 to 840 μg/cm 3 . Where the microbial activity was inhibited, the fluxes stabilized on a semi-steady-state level for the monocyclic aromatic hydrocarbons, naphthalene and 1-methylnaphthalene after a period of 10-20 days. Fluxes of acenaphthene and fluorene were only measurable in an experiment that utilized a cover soil with a low organic content. The fluxes were predicted by a numerical model assuming that the compounds acted independently of each other and that local equilibrium between the air, water, and sorbed phases existed. The model overestimated the fluxes for all the detected aromatic hydrocarbons by a factor of 1.3 to 12. When the cover soil was adapted to degrade naphthalene, the fluxes of naphthalene and 1-methylnaphthalene approached the detection limit after 5 to 8 days. Thereafter the fluxes of these two compounds were less than predicted by the model employing half-life values of 0.5 and 1 day for naphthalene and 1-methylnaphthalene respectively. 10 refs., 6 figs., 7 tabs

Importance of low-temperature distillation of coal for German fuel economics

Energy Technology Data Exchange (ETDEWEB)

Rosendahl, F

1942-01-01

Improved processes are available to give low-temperature distillation products economic importance. Low-temperature distillation is limited to the utilization of high-volatile nut coals and briquets. The coke formed can be used as a smokeless fuel, and the tar directly as a fuel oil. Phenols can be extracted, in order to work up the residue into fuel oil and motor fuel. Large deposits of coal in Upper Silesia and in the Saar District are suitable for low-temperature distillation.

In situ recovery of oil from Utah tar sand: a summary of tar sand research at the Laramie Energy Technology Center

Energy Technology Data Exchange (ETDEWEB)

Marchant, L.C.; Westhoff, J.D.

1985-10-01

This report describes work done by the United States Department of Energy's Laramie Energy Technology Center from 1971 through 1982 to develop technology for future recovery of oil from US tar sands. Work was concentrated on major US tar sand deposits that are found in Utah. Major objectives of the program were as follows: determine the feasibility of in situ recovery methods applied to tar sand deposits; and establish a system for classifying tar sand deposits relative to those characteristics that would affect the design and operation of various in situ recovery processes. Contents of this report include: (1) characterization of Utah tar sand; (2) laboratory extraction studies relative to Utah tar sand in situ methods; (3) geological site evaluation; (4) environmental assessments and water availability; (5) reverse combustion field experiment, TS-1C; (6) a reverse combustion followed by forward combustion field experiment, TS-2C; (7) tar sand permeability enhancement studies; (8) two-well steam injection experiment; (9) in situ steam-flood experiment, TS-1S; (10) design of a tar sand field experiment for air-stream co-injection, TS-4; (11) wastewater treatment and oil analyses; (12) economic evaluation of an in situ tar sand recovery process; and (13) appendix I (extraction studies involving Utah tar sands, surface methods). 70 figs., 68 tabs.

Stabilizing motor fuels

Energy Technology Data Exchange (ETDEWEB)

1935-07-12

Motor fuel is stabilized by adding less than 2% of a tar fraction from peat, coal, torbanite or shale, said fraction containing sufficient constituents boiling between 200 and 325/sup 0/C, to inhibit gum formation. Low-temperature coal-tar fractions are specified. The preferred boiling ranges are from 225 or 250/sup 0/ to 275/sup 0/C. In examples, the quantity added was 0.01%. The fuel may be a cracked distillate of gasoline boiling-point range or containing gasoline, and may contain relatively large proportions of di- and tri-olefines. The material added to the fuel may be (1) the tar fraction itself; (2) its alkali-soluble constituents; (3) its acid-soluble constituents; (4) a mixture of (2) and (3); (5) a blend of (2), (3) or (4) with a normal tar fraction; (6) the residue after extraction with alkali; (7) the residue after extraction with acid and alkali.

Effect of blending ratio to the liquid product on co-pyrolysis of low rank coal and oil palm empty fruit bunch

Directory of Open Access Journals (Sweden)

Zullaikah Siti

2018-01-01

Full Text Available The utilization of Indonesia low rank coal should be maximized, since the source of Indonesia law rank coals were abundant. Pyrolysis of this coal can produce liquid product which can be utilized as fuel and chemical feedstocks. The yield of liquid product is still low due to lower of comparison H/C. Since coal is non-renewable source, an effort of coal saving and to mitigate the production of greenhouse gases, biomass such as oil palm empty fruit bunch (EFB would added as co-feeding. EFB could act as hydrogen donor in co-pyrolysis to increase liquid product. Co-pyrolysis of Indonesia low rank coal and EFB were studied in a drop tube reactor under the certain temperature (t= 500 °C and time (t= 1 h used N2 as purge gas. The effect of blending ratios of coal/EFB (100/0, 75/25, 50/50, 25/75 and 0/100%, w/w % on the yield and composition of liquid product were studied systematically. The results showed that the higher blending ratio, the yield of liquid product and gas obtained increased, while the char decreased. The highest yield of liquid product (28,62 % was obtained used blending ratio of coal/EFB = 25/75, w/w%. Tar composition obtained in this ratio is phenol, polycyclic aromatic hydrocarbons, alkanes, acids, esters.

Maturation-related changes in the distribution of ester-bound fatty acids and alcohols in a coal series from the New Zealand Coal Band covering diagenetic to catagenetic coalification levels

DEFF Research Database (Denmark)

Glombitza, Clemens; Mangelsdorf, Kai; Horsfield, Brian

2009-01-01

A rank series of lignites and coals of low to moderate maturation levels (vitrinite reflectance (R0): 0.27–0.8%) from the New Zealand Coal Band were investigated using alkaline ester cleavage experiments to reveal compositional changes of ester bound components (fatty acids and alcohols) during...... increase during early catagenesis before decreasing again during main catagenesis. This intermittent increase was related to the short chain fatty acids. To obtain a maturity related signal and to eliminate facies related scattering in the amounts of fatty acids in the coal samples, the carbon preference...

Process for carbonizing, distilling, and vaporizing of coal from any source

Energy Technology Data Exchange (ETDEWEB)

Limberg, T

1916-10-15

A process is described for carbonizing, distilling, and vaporizing coal from any source, especially of humid and bituminous coals as well as bituminous shale and peat for recovering an especially light tar with a large aliphatic hydrocarbon content that is characterized in that it is exposed to internal heating under vacuum at a temperature below dull-red heat. The distillation products of the material are washed away by the heating gases for the whole length of the furnace and are removed immediately and carried into separate condensers.

Pulverized coal devolatilization prediction

International Nuclear Information System (INIS)

Rojas, Andres F; Barraza, Juan M

2008-01-01

The aim of this study was to predict the two bituminous coals devolatilization at low rate of heating (50 Celsius degrade/min), with program FG-DVC (functional group Depolymerization. Vaporization and crosslinking), and to compare the devolatilization profiles predicted by program FG-DVC, which are obtained in the thermogravimetric analyzer. It was also study the volatile liberation at (10 4 k/s) in a drop-tube furnace. The tar, methane, carbon monoxide, and carbon dioxide, formation rate profiles, and the hydrogen, oxygen, nitrogen and sulphur, elemental distribution in the devolatilization products by FG-DVC program at low rate of heating was obtained; and the liberation volatile and R factor at high rate of heating was calculated. it was found that the program predicts the bituminous coals devolatilization at low rate heating, at high rate heating, a volatile liberation around 30% was obtained

Utilisation of chemically treated coal

Directory of Open Access Journals (Sweden)

Bežovská Mária

2002-03-01

Full Text Available The numerous application of coal with high content of humic substances are known. They are used in many branches of industry. The complex study of the composition of coal from upper Nitra mines has directed research to its application in the field of ecology and agriculture. The effective sorption layers of this coal and their humic acids can to trap a broad spectrum of toxic harmful substances present in industrial wastes, particularly heavy metals. A major source of humic acids is coal - the most abundant and predominant product of plant residue coalification. All ranks of coal containt humic acids but lignite from Nováky deposit represents the most easily available and concentrated form of humic acids. Deep oxidation of coal by HNO3 oxidation - degradation has been performed to produce water-soluble-organic acids. The possibilities of utilisation of oxidised coal and humic acids to remove heavy metals from waste waters was studied. The residual concentrations of the investigated metals in the aqueous phase were determined by AAs. From the results follows that the samples of oxidised coal and theirs humic acids can be used for the heavy metal removal from metal solutions and the real acid mine water.Oxidised coal with a high content of humic acids and nitrogen is used in agriculture a fertilizer. Humic acids are active component in coal and help to utilize almost quantitatively nitrogen in soil. The humic substances block and stabiliz toxic metal residues already present in soil.

Change in surface characteristics of coal in upgrading of low-rank coals; Teihin`itan kaishitsu process ni okeru sekitan hyomen seijo no henka

Energy Technology Data Exchange (ETDEWEB)

Oki, A.; Xie, X.; Nakajima, T.; Maeda, S. [Kagoshima University, Kagoshima (Japan). Faculty of Engineering

1996-10-28

With an objective to learn mechanisms in low-rank coal reformation processes, change of properties on coal surface was discussed. Difficulty in handling low-rank coal is attributed to large intrinsic water content. Since it contains highly volatile components, it has a danger of spontaneous ignition. The hot water drying (HWD) method was used for reformation. Coal which has been dry-pulverized to a grain size of 1 mm or smaller was mixed with water to make slurry, heated in an autoclave, cooled, filtered, and dried in vacuum. The HWD applied to Loy Yang and Yallourn coals resulted in rapid rise in pressure starting from about 250{degree}C. Water content (ANA value) absorbed into the coal has decreased largely, with the surface made hydrophobic effectively due to high temperature and pressure. Hydroxyl group and carbonyl group contents in the coal have decreased largely with rising reformation treatment temperature (according to FT-IR measurement). Specific surface area of the original coal of the Loy Yang coal was 138 m{sup 2}/g, while it has decreased largely to 73 m{sup 2}/g when the reformation temperature was raised to 350{degree}C. This is because of volatile components dissolving from the coal as tar and blocking the surface pores. 2 refs., 4 figs.

Thermal relaxation of bituminous coal to improve donation ability of hydrogen radicals in flash pyrolysis; Sekitan kozo kanwa ni yoru suiso radical kyoyo noryoku no kojo wo mezashita netsubunkai mae shori

Energy Technology Data Exchange (ETDEWEB)

Mori, T.; Isoda, T.; Kusakabe, K.; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Hayashi, J. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology

1996-10-28

In terms of coal conversion reaction, the behavior of bituminous coal heated beyond a glass transition point was examined on the basis of pyrolyzed products, and the effect of an increase in proton mobility on promotion of coal decomposition was evaluated. In experiment, after Illinois bituminous coal specimen was heated up to a specific temperature in N2 or He gas flow at a rate of 5K/min, the specimen was directly transferred to a pyrolyzer for instantaneous pyrolysis. As the experimental result, the glass transition temperature of the Illinois coal specimen was calculated to be 589K from a differential scanning calorimetry (DSC) profile. From the pyrolysis result of the Illinois coal specimen heated up to 623K, the char yield decreased by 3kg as compared with that of the original coal, while the tar yield increased by 4kg up to 27kg per 100kg of the original coal. This tar increase was larger than that of cooled coal. These results suggested that the donation of hydrogen radicals to coal fragments is improved with an increase in proton mobility. 4 refs., 4 figs., 1 tab.

Report of National Research Institute for Pollution and Resources for fiscal 1979. Research on conversion of coal to petroleum, research on coal liquefaction, high pressure liquid phase hydrogenation of coal by continuous test equipment, and manufacture of coal chemicals; 1979 nendo sekitan no yuka no kenkyu / sekitan no ekika no kenkyu / renzoku shiken sochi ni yoru sekitan no koatsu ekiso suisoka bunkai / coal chemicals no seizo

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-07-01

Research was conducted on conversion of coal to petroleum for the purpose of securing substitute liquid fuel. Recovery of hydrogen from the waste gas from the conversion process was explained, as were the conversion results from various coals produced in Japan. In coal liquefaction researches with the aim of manufacturing artificial petroleum, a report was made on each of the researches, i.e., the experiment results of coal liquefaction using various catalysts, manufacture of hydrogen by water gas reaction, catalytic action against coal paste, action of mixed oil and pressure against coal paste, result of hydrogen adding test for coal paste using an intermediate scale device, test result of secondary hydrogen addition for coal liquefied oil, and the test result of continuous secondary hydrogen addition for the liquefied oil. In the manufacture of fuel oil by hydro-cracking of coal or tar, a report was made on high pressure liquid phase hydrogenation of coal using a continuous testing device. Aromatic chemicals useful as chemical materials are supposed to be obtained by cutting inter-polymerized-unit bonding to make low molecules from the chemical structure of coal, removing surrounding radicals and simplifying it. A report was also made on the experiment of manufacturing coal chemicals by combination of high pressure liquid phase hydrogenation and hydro-dealkylation. (NEDO)

Serum Level of Antibodies (IgG, IgM Against Benzo[a]pyrene-7,8-diol-9,10-epoxide-DNA Adducts in Children Dermatologically Exposed to Coal Tar

Directory of Open Access Journals (Sweden)

Pavel Borský

2017-06-01

Full Text Available Crude coal tar (CCT contains polycyclic aromatic hydrocarbons (PAHs. Benzo[a]pyrene (BaP is metabolized into a highly reactive metabolite benzo[a]pyrene-7,8-diol-9,10-epoxide (BPDE that is able to bind to DNA and creates BPDE-DNA adducts. Adducted DNA becomes immunogenic and induces immune response by production of antibodies against BPDE-DNA adducts (Ab-BPDE-DNA. Circulating Ab-BPDE-DNA was proposed as potential biomarker of genotoxic exposure to BaP (PAHs. Goeckerman therapy (GT of psoriasis uses dermal application of CCT ointment (PAHs. In presented study (children with psoriasis treated by GT; n = 19 the therapy significantly increased the level of Ab-BPDE-DNA (EI = 0.29/0.19–0.34 vs. 0.31/0.25–0.40; median/lower–upper quartile; p < 0.01. The results support the idea of Ab-BPDE-DNA level as a possible tentative indicator of exposure, effects and susceptibility of the organism to the exposure of BaP (PAHs.

Utilisation of chemically treated coal

International Nuclear Information System (INIS)

Bezovska, M.

2002-01-01

The numerous application of coal with high content of humic substances are known. They are used in many branches of industry. The complex study of the composition of coal from upper Nitra mines has directed research to its application in the field of ecology and agriculture. The effective sorption layers of this coal and their humic acids can trap a broad spectrum of toxic harmful substances present in industrial wastes, particularly heavy metals. A major source of humic acids is coal - the most abundant and predominant product of plant residue coalification. All ranks of coal contain humic acids but lignite from Novaky deposit represents the most easily available and concentrated from of humic acids. The possibilities of utilisation of humic acids to remove heavy metals from waste waters was studied. The residual concentrations of the investigated metals in the aqueous phase were determined by AAs. From the results follows that the samples of coals humic acids can be used for the heavy metal removal from metal solutions and the real acid mine water. Oxidised coal with high content of humic acids and nitrogen is used in agriculture as fertilizer. Humic acids are active component in coal and can help to utilize almost quantitatively nitrogen in soil. The humic substances block and stabilize toxic metal residues already present in soil. (author)

The temporal relationship between advertising and sales of low-tar cigarettes.

Science.gov (United States)

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-12-01

To determine whether a temporal relationship exists between the advertising and sales of low-tar cigarettes. It was hypothesised that increases in the advertising of low-tar cigarettes would precede increases in sales for these cigarettes. The themes of cigarette advertisements were reviewed and coded for 20 low-tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low-tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low-tar attributes of the cigarette advertised, the advertisement was coded as having a low-tar theme and was included in the analysis. Five different graphical presentations of the relationship between the advertising and sales of the 20 low-tar cigarette brands showed a temporal relationship between low-tar advertising and sales for these brands. This relationship was observed for brands that introduced a low-tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low-tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low-tar brands, sales of these brands remained low relative to sales of the low-tar alternative brands. Increases in print advertising of 20 of the most popular low-tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low-tar brands in the mid-1970s and early 1980s, the sales of these brands never matched the sales of the low-tar alternative brands. This suggests that it may have been easier to get smokers to switch to low-tar brands within a brand family compared with entirely new low-tar brands. Over the past 30 years, the marketing of low-tar cigarettes as a healthier alternative to higher-tar cigarettes has resulted in these brands

Polycyclic aromatic hydrocarbon contamination of American lobster, Homarus americanus, in the proximity of a coal-coking plant

Energy Technology Data Exchange (ETDEWEB)

Uthe, J F; Musial, C J

1986-11-01

Polycyclic aromatic hydrocarbons (PAH) are ubiquitous environmental contaminants resulting predominantly from anthropogenic pyrolytic and combustion processes. In addition to the usual methods of aerial and aqueous transport to the coastal marine environment substantial amounts of PAH are added through the use of products such as creosote, coal tar and coal tar pitch as preservative and antifouling agents in the marine environment. Many PAH compounds are known carcinogenic agents and are rapidly taken up by fish and shellfish from water. Therefore as human foodstuffs many of these shellfish species warrant monitoring for PAH. A study of PAH in lobster tissues has been carried out using lobsters captured in Sydney harbour, Nova Scotia, Canada. Two coal-coking ovens on the shore have discharged their liquid effluents into the harbour. Lobsters from this area were sampled in 1982 and 1984. This paper presents the materials and methods used in the sampling, the results and discussion of them. The results confirmed the ability of lobsters to accumulate extremely high amounts of PAH in their tissues. 14 references.

The temporal relationship between advertising and sales of low‐tar cigarettes

Science.gov (United States)

Reed, Mark B; Anderson, Christy M; Burns, David M

2006-01-01

Objective and hypothesis To determine whether a temporal relationship exists between the advertising and sales of low‐tar cigarettes. It was hypothesised that increases in the advertising of low‐tar cigarettes would precede increases in sales for these cigarettes. Methods The themes of cigarette advertisements were reviewed and coded for 20 low‐tar cigarette brands advertised in 13 widely read magazines in the US between 1960 and 1996. These 20 brands represented most of the low‐tar cigarette advertisements and cigarette sales from 1967 to 1996. Cigarette sales data were obtained from the 1994 Maxwell report that summarises all cigarette sales from 1925 to 1990. If the advertisement referred to the low‐tar attributes of the cigarette advertised, the advertisement was coded as having a low‐tar theme and was included in the analysis. Results Five different graphical presentations of the relationship between the advertising and sales of the 20 low‐tar cigarette brands showed a temporal relationship between low‐tar advertising and sales for these brands. This relationship was observed for brands that introduced a low‐tar alternative into an existing brand family (eg, Marlboro Light) and for new exclusively low‐tar brands (eg, Carlton). Despite large increases in the advertising for the exclusively low‐tar brands, sales of these brands remained low relative to sales of the low‐tar alternative brands. Conclusions Increases in print advertising of 20 of the most popular low‐tar cigarette brands were followed by increases in sales for these cigarettes. Despite increases in the advertising of exclusively low‐tar brands in the mid‐1970s and early 1980s, the sales of these brands never matched the sales of the low‐tar alternative brands. This suggests that it may have been easier to get smokers to switch to low‐tar brands within a brand family compared with entirely new low‐tar brands. Over the past 30 years, the marketing of low‐tar

Characterization of Tar Deposits, Extraction and Sorption Properties

Directory of Open Access Journals (Sweden)

Pryszcz Adrian

2016-06-01

Full Text Available The main goal of this paper was to characterize and find a useful solution for the decomposition of tar deposits. For the experimental part, tar deposits, formed by polymerization and condensation reactions, were chosen from a storage tank for tars. At first the initial analyses of tar deposits (elemental, thermogravimetric, and calorimetric analyses were performed. After the characterization, the tar deposits were extracted in the Soxhlet extractor by acetone, toluene, and quinolone and activated with potassium hydroxide. As the final step of this work, the sorption characterization on the 3Flex Surface Characterization Analyzer (Micromeritics was performed. The specific surface area of the samples was evaluated using two methods - a single point measurement at p/p0=0.2 and BET method. Micropore and external surface areas were calculated based on a t-plot analysis (carbon black model.

Corrosão de parafusos fixados à madeira tratada com soluções de creosoto vegetal Corrosion of screws fixed into wood treated with wood tar creosote solutions

Directory of Open Access Journals (Sweden)

Juarez Benigno Paes

2002-05-01

of 16 preservative solutions were prepared, of which 14 were enriched, besides the crude wood tar creosote and the purified wood tar creosote. Stakes made of Eucalyptus grandis sapwood were treated following the full-cell process (Bethell's process. After the stakes treatment, screws of iron covered with zinc were fixed into the wood stakes. The assay was carried out in three locations (Viçosa, Ponte Nova and Leopoldina - in Zona da Mata, Minas Gerais, Brazil. The corrosiveness of solutions of wood tar creosote was compared with the one caused by coal tar creosote. The solutions with purified wood tar creosote were less corrosive than those prepared with crude wood tar creosote, being similar to the coal tar creosote.

Application of adsorption analysis to the investigation of phenols and bases in low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Kalechts, I V; Salimgareeva, F G; Tumbusova, Z P

1955-01-01

The use of chromatographic adsorption for the separation of mono- and bicyclic phenols and bases from coal tar and from its hydrogenation products were studied with o-cresol, ..beta..-naphthol, pyridine, and quinoline. Experimental data show that Al/sub 2/O/sub 3/ was preferable for separating phenols, but that silica gel was better for the bases. The best order of use of the developers was as follows: C/sub 6/H/sub 6/, Et/sub 2/O, EtOH. The data show that the destructive hydrogenation process degrades the higher series phenols to lower ones.

Characterization and organic electric-double-layer-capacitor application of KOH activated coal-tar-pitch-based carbons: Effect of carbonization temperature

Science.gov (United States)

Choi, Poo Reum; Lee, Eunji; Kwon, Soon Hyung; Jung, Ji Chul; Kim, Myung-Soo

2015-12-01

The present study reports the influence of pre-carbonization on the properties of KOH-activated coal tar pitch (CTP). The change of crystallinity and pore structure of pre-carbonized CTPs as well as their activated carbons (ACs) as function of pre-carbonization temperature are investigated. The crystallinity of pre-carbonized CTPs increases with increasing the carbonization temperature up to 600 °C, but a disorder occurs during the carbonization around 700 °C and an order happens gradually with increasing the carbonization temperatures in range of 800-1000 °C. The CTPs pre-carbonized at high temperatures are more difficult to be activated with KOH than those pre-carbonized at low temperatures due to the increase of micro-crystalline size and the decrease of surface functional groups. The micro-pores and meso-pores are well developed at around 1.0 nm and 2.4 nm, respectively, as the ACs are pre-carbonized at temperatures of 500-600 °C, exhibiting high specific capacitances as electrode materials for electric double layer capacitor (EDLC). Although the specific surface area (SSA) and pore volume of ACs pre-carbonized at temperatures of 900-1000 °C are extraordinary low (non-porous) as compared to those of AC pre-carbonized at 600 °C, their specific capacitances are comparable to each other. The large specific capacitances with low SSA ACs can be attributed to the structural change resulting from the electrochemical activation during the 1st charge above 2.0 V.

Bacterial reduction of selenium in coal mine tailings pond sediment

Energy Technology Data Exchange (ETDEWEB)

Siddique, T.; Arocena, J.M.; Thring, R.W.; Zhang, Y.Q. [University of North British Columbia, Prince George, BC (Canada)

2007-05-15

Sediment from a storage facility for coal tailings solids was assessed for its capacity to reduce selenium (Se) by native bacterial community. One Se{sup 6+}-reducing bacterium Enterobacter hormaechei (Tar11) and four Se{sup 4+}-reducing bacteria, Klebsiella pneumoniae (Tar1), Pseudomonasfluorescens (Tar3), Stenotrophomonas maltophilia (Tar6), and Enterobacter amnigenus (Tar8) were isolated from the sediment. Enterobacter horinaechei removed 96% of the added Se{sup 6+} (0.92 mg L{sup -1} from the effluents when Se6+ was determined after 5 d of incubation. Analysis of the red precipitates showed that Se{sup 6+} reduction resulted in the formation of spherical particles ({lt}1.0 {mu} m) of Se 0 as observed under scanning electron microscope (SEM) and confirmed by EDAX. Selenium speciation was performed to examine the fate of the added Se{sup 6+} in the sediment with or without addition of Enterobacter hormaechei cells. More than 99% of the added Se{sup 6+} (about 2.5 mg L{sup -1}) was transformed in the nonsterilized sediment (without Enterobacter hormaechei cells) as well as in the sterilized (heat-killed) sediment (with Enterobacter hormaechei cells). The results of this study suggest that the lagoon sediments at the mine site harbor Se{sup 6+}- and Se{sup 4+} -reducing bacteria and may be important sinks for soluble Se (Se{sup 6+} and Se{sup 4+}). Enterobacter hormaechei isolated from metal-contaminated sediment may have potential application in removing Se from industrial effluents.

40 CFR Appendix I to Part 192 - Listed Constituents

Science.gov (United States)

2010-07-01

...-dimethoxyphenyl)azo]-) Coal tar creosote Copper cyanide (CuCN) Creosote Cresol (Chresylic acid) (Phenol, methyl... (Phosphorodithioic acid, O,O-diethyl S-methyl ester) Diethyl-p-nitrophenyl phosphate (Phosphoric acid, diethyl 4... (Acetic acid, lead(2+) salt) Lead phosphate (Phosphoric acid, lead(2+) salt(2:3)) Lead subacetate (Lead...

New method for the exact determination of phenols in low-temperature tar and tar oils

Energy Technology Data Exchange (ETDEWEB)

Lambris, G; Haferkorn, H

1949-01-01

A 3-gram sample of water-free tar or tar oil containing approximately 50% phenols is dissolved in a mixture of benzene and xylene and a known excess of a 20% KOH solution of known normality saturated with benzene and xylene is added. Weight of the KOH is determined by difference. This mixture is shaken repeatedly in a 300-milliliter separatory funnel. After standing for 0.5 h, the dark or almost black phenolate solution containing the major portion is separated and weighed. Care must be taken to prevent the induction of solids. The phenolate in the residue is extracted with hot water and titrated with 0.2N HCl and 1 ml. Congo red (1:100). If water is present in the tar or tar oil, 100 ml of xylene is added immediately after weighing and the water separated by distillation the weight of which must be determined. Any phenols carried over are dissolved in the small quantity of xylene in the distillate. This quantity is added to the bulk of the xylene. After any remaining phenols are extracted from the tar residue with boiling benzene, the benzene-xylene mixture is treated with KOH as above. The accuracy of the method is estimated to be +-1% as shown by experiments with phenol; o-, m-, and p-cresol; cresol mixture; and pyrocatechol. The weight of the dissolved phenols X is determined by X = c - a + cd/(ab - d) where a = weight of KOH, b = HCl used per gram of KOH, C = weight of major portion of phenolate solution, which is formed by shaking the phenol solution with KOH, d = HCl used for titration of phenolate residue.

Depolymerization of coal by O2 oxidation followed by acid hydrolysis; Sanso sanka-kasui bunkai ni yoru sekitan no teionkai jugo

Energy Technology Data Exchange (ETDEWEB)

Aizawa, S.; Hayashi, J.; Kumagai, H.; Chiba, T. [Hokkaido University, Sapporo (Japan). Center for Advanced Research of Energy Technology; Morooka, S. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1996-10-28

With an objective to elucidate characteristics of oxygen addition to coal, and characteristics of solvent extraction by means of depolymerization, experiments were performed on oxygen oxidation and acid hydrolysis of brown coals. Coals used for the experiments are Morwell (MW), Yallourn (YL) , South Banko (SB) and Wyoming (WY) coals. Test samples were suspended in weak alkaline aqueous solution, and then oxygen was blown into them with pressure kept at atmospheric pressure. After a lapse of a predetermined time, the samples were cooled, and made as acidic as pH 1.3 in hydrochloric acid, followed by acid hydrolysis. Oxygen consumption increased with the reaction time, and with the MW coal, one mol oxygen reacted to 11 mols of coal. Spectral analysis on the YL and WY coal experiments revealed that aliphatic carbon combined with aromatic carbon or ether group has turned to peroxide, whose C-C or C-O bond was broken down as a result of acid hydrolysis of the peroxide, producing oxygen containing compounds. As a result of the depolymerization, the rate of extraction by using DMF, DMSO and methanol/THF mixed solvent increased to 90% or higher. Proportion of bond and cutting-off affects largely collapse of the cross-link structure. The carbon conversion to volatiles was at most 4%. 1 ref., 10 figs.

Non-slag co-gasification of biomass and coal in entrained-bed furnace

Science.gov (United States)

Itaya, Yoshinori; Suami, Akira; Kobayashi, Nobusuke

2018-02-01

Gasification is a promising candidate of processes to upgrade biomass and to yield clean gaseous fuel for utilization of renewable energy resources. However, a sufficient amount of biomass is not always available to operate a large scale of the plant. Co-gasification of biomass with coal is proposed as a solution of the problem. Tar emission is another subject during operation in shaft or kiln type of gasifiers employed conventionally for biomass. The present authors proposed co-gasification of biomass and coal in entrained-bed furnace, which is a representative process without tar emission under high temperature, but operated so to collect dust as flyash without molten slag formation. This paper presents the works performed on co-gasification performance of biomass and pulverized coal to apply to entrained-bed type of furnaces. At first, co-gasification of woody powder and pulverized coal examined using the lab-scale test furnace of the down-flow entrained bed showed that the maximum temperatures in the furnace was over 1500 K and the carbon conversion to gas achieved at higher efficiency than 80-90 percent although the residence time in the furnace was as short as a few seconds. Non-slag co-gasification was carried out successfully without slag formation in the furnace if coal containing ash with high fusion temperature was employed. The trend suggesting the effect of reaction rate enhancement of co-gasification was also observed. Secondary, an innovative sewage sludge upgrading system consisting of self-energy recovery processes was proposed to yield bio-dried sludge and to sequentially produce char without adding auxiliary fuel. Carbonization behavior of bio-dried sludge was evaluated through pyrolysis examination in a lab-scale quartz tube reactor. The thermal treatment of pyrolysis of sludge contributed to decomposition and removal of contaminant components such as nitrogen and sulfur. The gasification kinetics of sludge and coal was also determined by a

Sunflower oil in the treatment of hot tar burns.

Science.gov (United States)

Türegün, M; Oztürk, S; Selmanpakoğlu, N

1997-08-01

Hot tar burns compose a unique class of thermal injury, because removal of this highly sticky compound may be very difficult without inflicting additional tissue damage. Early removal of tar facilitates assessment of the burn and improves patient comfort. Although the use of many substances for the painless removal of tar has been described, we used sunflower oil effectively in the treatment of four tar burn patients. This first report describes the practical and successful use of sunflower oil which was easily obtained from the hospital kitchen.

Tar dew point analyser as a tool in biomass gasification

Energy Technology Data Exchange (ETDEWEB)

Vreugdenhil, B.J.; Kuipers, J. [ECN Biomass, Coal and Environmental Research, Petten (Netherlands)

2008-08-15

Application of the Tar Dew point Analyzer (TDA) in different biomass based gasification systems and subsequent gas cleaning setups has been proven feasible. Such systems include BFB gasifiers, CFB gasifier and fixed bed gasifiers, with tar crackers or different scrubbers for tar removal. Tar dew points obtained with the TDA give direct insight in the performance of the gas cleaning section and help prevent any tar related problems due to condensation. The current TDA is capable of measuring tar dew points between -20 to 200C. This manuscript will present results from 4 different gasification setups. The range of measured tar dew points is -7 to 164C with comparable results from the calculated dew points based on the SPA measurements. Further detail will be presented on the differences between TDA and SPA results and explanations will be given for deviations that occurred. Improvements for the TDA regarding future work will be presented.

Low severity conversion of activated coal

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

Acid leaching of coal: to produce clean fuels from Turkish lignite

Energy Technology Data Exchange (ETDEWEB)

Seferinoglu, Meryem [Mineral Research and Exploration Directorate (Turkey)], email: meryem_seferinoglu66@yahoo.com; Duzenli, Derya [Ankara Central Laboratory (Turkey)

2011-07-01

With the increasing concerns about the environment, energy producers and governments are looking at developing clean energy sources. However, Turkey has limited clean energy resources and is using low grade coal which has high sulphur content as an alternative energy source. The aim of this paper is to study the possibility of generating clean fuel from Edirne Lignite and to get a better understanding of chemical mechanisms involved in coal leaching with hydrofluoric acid (HF) solutions. Leaching was conducted on Edirne Lignite with HF solution at ambient temperature and the effects of parameters such as reaction time and concentration of acid solutions on the process were evaluated. The optimum conditions were found and it was shown that ash levels can be reduced from 28.9% to 10.5% and the calorific value increased by 500kcal/kg with the HF leaching method. This study demonstrated that the production of clean fuel from high sulphur lignite is possible.

Formation of N{sub 2} during the fixed-bed pyrolysis of coals

Energy Technology Data Exchange (ETDEWEB)

Wu, Zhiheng; Ohtsuka, Yasuo [Tohoku Univ., Sendai (Japan); Furimsky, E. [Natural Resources Canada, Ottawa, Ontario (Canada)

1995-12-31

Research on the fate of the nitrogen in coal during pyrolysis has attracted increased attention, since it is related with the NO{sub x} and N{sub 2}O emissions during subsequent combustion. It has been reported that coal nitrogen is initially released as tar, which is then converted to HCN and NH{sub 3} through secondary decomposition reactions. However, little attention to N{sub 2} has been paid so far. We have recently found that N{sub 2} is the dominant product in slow heating rate pyrolysis of a subbituminous coal, and that the finely dispersed iron catalyst promotes drastically the formation of N{sub 2} from a brown coal. If coal nitrogen can be removed efficiently as N{sub 2} during pyrolysis, this method would contribute to the reduction of the NO{sub x} and N{sub 2}O emissions, since such pollutants originate mostly from coal nitrogen. Therefore the present study aims at making clear the influence of coal type, pyrolysis conditions, demineralization, and iron catalyst on the formation of N{sub 2} during the fix-bed pyrolysis of several coals with different ranks.

Reaction Mechanism of Tar Evolution in Biomass Steam Gasification for Hydrogen Production

International Nuclear Information System (INIS)

Shingo Katayama; Masahiro Suzuki; Atsushi Tsutsumi

2006-01-01

Reaction mechanism of tar evolution in steam gasification of biomass was investigated with a continuous cross-flow moving bed type differential reactor, in which tar and gases can be fractionated according to reaction time. We estimated that time profile of tar and gas evolution in the gasification of cellulose, xylan, and lignin, and compared it with experimental product time profile of real biomass gasification. The experimental tar evolution rate is different from estimated tar evolution rate. The estimated tar evolution rate has a peak at 20 s. On the other hand, the experimental tar evolution rate at 20 s is little, and tar at initial stage includes more water-soluble and water-insoluble compounds. It can be concluded that in the real biomass steam gasification the evolution of tar from cellulose and lignin component was found to be precipitated by that from hemi-cellulose component. (authors)

Site-selective probing of cTAR destabilization highlights the necessary plasticity of the HIV-1 nucleocapsid protein to chaperone the first strand transfer

Science.gov (United States)

Godet, Julien; Kenfack, Cyril; Przybilla, Frédéric; Richert, Ludovic; Duportail, Guy; Mély, Yves

2013-01-01

The HIV-1 nucleocapsid protein (NCp7) is a nucleic acid chaperone required during reverse transcription. During the first strand transfer, NCp7 is thought to destabilize cTAR, the (−)DNA copy of the TAR RNA hairpin, and subsequently direct the TAR/cTAR annealing through the zipping of their destabilized stem ends. To further characterize the destabilizing activity of NCp7, we locally probe the structure and dynamics of cTAR by steady-state and time resolved fluorescence spectroscopy. NC(11–55), a truncated NCp7 version corresponding to its zinc-finger domain, was found to bind all over the sequence and to preferentially destabilize the penultimate double-stranded segment in the lower part of the cTAR stem. This destabilization is achieved through zinc-finger–dependent binding of NC to the G10 and G50 residues. Sequence comparison further revealed that C•A mismatches close to the two G residues were critical for fine tuning the stability of the lower part of the cTAR stem and conferring to G10 and G50 the appropriate mobility and accessibility for specific recognition by NC. Our data also highlight the necessary plasticity of NCp7 to adapt to the sequence and structure variability of cTAR to chaperone its annealing with TAR through a specific pathway. PMID:23511968

DECOMPOSITION OF TARS IN MICROWAVE PLASMA – PRELIMINARY RESULTS

Directory of Open Access Journals (Sweden)

Mateusz Wnukowski

2014-07-01

Full Text Available The paper refers to the main problem connected with biomass gasification - a presence of tar in a product gas. This paper presents preliminary results of tar decomposition in a microwave plasma reactor. It gives a basic insight into the construction and work of the plasma reactor. During the experiment, researches were carried out on toluene as a tar surrogate. As a carrier gas for toluene and as a plasma agent, nitrogen was used. Flow rates of the gases and the microwave generator’s power were constant during the whole experiment. Results of the experiment showed that the decomposition process of toluene was effective because the decomposition efficiency attained above 95%. The main products of tar decomposition were light hydrocarbons and soot. The article also gives plans for further research in a matter of tar removal from the product gas.

Biological monitoring as a useful tool for the detection of a coal-tar contamination in bitumen-exposed workers

Energy Technology Data Exchange (ETDEWEB)

Raulf-Heimsoth, M.; Angerer, J.; Pesch, B.; Marczynski, B.; Hahn, J.U.; Spickenheuer, A.; Preuss, R.; Ruhl, R.; Rode, P.; Bruning, T. [Institute at the Ruhr University of Bochum, Bochum (Germany)

2008-07-01

In our research project entitled 'Chemical irritative and/or genotoxic effect of fumes of bitumen under high processing temperatures on the airways,' 73 mastic asphalt workers exposed to fumes of bitumen and 49 construction nonexposed workers were analyzed and compared with respect to polycyclic aromatic hydrocarbons (PAHs) exposure and exposure-related health effects. In order to assess the internal exposure the monohydroxylated metabolites of pyrene, 1-hydroxypyrene (1-OHP), and phenanthrene, 1-, 2- and 9-, and 3- and 4-hydroxyphenanthrene (OHPH) were determined in pre- and post-shift urinary samples. Significantly higher concentrations 1-OHP and OHPH were detected in the post-shift urine samples of 7 mastic asphalt workers working on the same construction site compared to the reference workers and all other 66 mastic asphalt workers. The adjusted mean OHPH in the reference, 66 mastic worker, and 7 worker subgroups was 1022, 1544, and 12919 ng/g creatinine (crn) respectively, indicating a marked rise in the 7 worker subgroup. In addition, there was a more than 12-fold increase of PAH metabolites from pre- to post-shift in these 7 workers, whereas in the other mastic asphalt workers there was only a twofold rise in PAH-metabolite concentration between pre- and post-shift values. The analysis of a drilling core from the construction site of the seven workers led to the detection of the source for this marked PAH exposure during the working shift as being coal tar plates, which were, without knowledge of the workers and coordinators, the underground material of the mastic asphalt layer. The evaluation of the stationary workplace concentration showed enhanced levels of phenanthrene, pyrene, fluorene, anthracene, and acenaphthene during working shifts at the construction site of these seven workers. Our study shows that biological monitoring is also a useful tool for the detection of unrecognized sources with high PAH concentrations.

Durability and regeneration of catalysts of the iron family in hydrogenation of low-temperature tar

Energy Technology Data Exchange (ETDEWEB)

Funasaka, W; Yokogawa, C; Hayashi, K; Kawamura, T; Fujita, H; Suga, S

1949-01-01

The low-temperature tar consisting of neutral and acidic oils has been reduced under atmospheric pressure between 400/sup 0/ and 500/sup 0/ by using catalysts prepared from Fe-Cr-kieselguhr, yellow ocher, and other material. When the reduction was performed at 480/sup 0/ with the yellow ocher from Niwasaka, Fukushima Prefacture, Japan, the low-temperature tar was easily converted to neutral and light oils and the catalysts could be regenerated by repeated baking and reduction. It is concluded that the commercialization of this reduction process is possible by using a cycle (each takes 20 minutes) composed of catalytic reaction, baking, and reduction of the catalysts.

High-BTU gas production from tar-bearing hot coke oven gas over iron catalyst

Energy Technology Data Exchange (ETDEWEB)

L.Y. Li; K. Morishita; T. Takarada [Gunma University, Gunma (Japan). Department of Biological and Chemical Engineering

2005-07-01

To utilize the tar-bearing hot coke oven gas (the by-product of coke making process) more effectively, a process was developed by converting the hot coke oven gas into a methane rich high-BTU gas over iron-bearing catalysts. The catalytic behaviour of Indonesian limonite ore was mainly discussed. For a reference, a conventional nickel catalyst (Ni/Al{sub 2}O{sub 3}) was employed. Laboratory scale tests were carried out in a two-stage fixed-bed reactor at ambient pressure. A bituminous coal sample was heated at first stage, the volatiles was carried by feed gas and decomposed at second stage. The limonite promoted hydropyrolysis of coal volatiles similar to Ni/Al{sub 2}O{sub 3} catalyst. High yields of total product gas and methane were obtained at 50 vol.% hydrogen atmosphere with a feed gas of 60 ml min{sup -1} hydrogen and 60 ml min{sup -1} nitrogen. After experiments, hydrocarbons heavier than ethane were not observed. Also that, carbon balance was more than 99.8% in coal char, product gases and carbon deposits. It was considered that coal volatiles converted into light gases and carbon almost completely in catalyst bed. Yields of product gas and methane depended upon catalytic temperature. At 923 K, the maximum yield of product gas was achieved at 74.3% for limonite catalyst on carbon balance with methane 83.2 vol.% of the carbonaceous gas products. Comparing with limonite, Fe/Al{sub 2}O{sub 3} and BOF dust samples showed low activities on coal volatiles catalytic decomposition. 21 refs., 5 figs., 3 tabs.

Catalytic destruction of tar in biomass derived producer gas

International Nuclear Information System (INIS)

Zhang Ruiqin; Brown, Robert C.; Suby, Andrew; Cummer, Keith

2004-01-01

The purpose of this study is to investigate catalytic destruction of tar formed during gasification of biomass, with the goal of improving the quality of the producer gas. This work focuses on nickel based catalysts treated with alkali in an effort to promote steam gasification of the coke that deposits on catalyst surfaces. A tar conversion system consisting of a guard bed and catalytic reactor was designed to treat the producer gas from an air blown, fluidized bed biomass gasifier. The guard bed used dolomite to crack the heavy tars. The catalytic reactor was used to evaluate three commercial steam reforming catalysts. These were the ICI46-1 catalyst from Imperial Chemical Industry and Z409 and RZ409 catalysts from Qilu Petrochemical Corp. in China. A 0.5-3 l/min slipstream from a 5 tpd biomass gasifier was used to test the tar conversion system. Gas and tar were sampled before and after the tar conversion system to evaluate the effectiveness of the system. Changes in gas composition as functions of catalytic bed temperature, space velocity and steam/TOC (total organic carbon) ratio are presented. Structural changes in the catalysts during the tests are also described

Production of oil from Intermountain West tar sands deposits

Energy Technology Data Exchange (ETDEWEB)

Glassett, J.M.; Glassett, J.A.

1976-03-01

Six tar sand deposits in the Intermountain West, each containing more than one billion barrels of oil in place, are identified. All of these deposits are in eastern Utah and contain a total of twenty-eight billion barrels of oil. The names of the six deposits arranged in descending order of desirability for large-scale surface-mining oil recovery operations are as follows: Sunnyside, Tar Sand Triangle, Asphalt Ridge, P.R. Spring, Circle Cliffs, and Hill Creek. An overview of each deposit is presented including geology, surface-mining variables, chemical processing variables, environmental aspects, and economics. A comparison of Utah tar sands and Athabasca, Alberta, Canada tar sands is also presented.

Solar coal gasification reactor with pyrolysis gas recycle

Science.gov (United States)

Aiman, William R.; Gregg, David W.

1983-01-01

Coal (or other carbonaceous matter, such as biomass) is converted into a duct gas that is substantially free from hydrocarbons. The coal is fed into a solar reactor (10), and solar energy (20) is directed into the reactor onto coal char, creating a gasification front (16) and a pyrolysis front (12). A gasification zone (32) is produced well above the coal level within the reactor. A pyrolysis zone (34) is produced immediately above the coal level. Steam (18), injected into the reactor adjacent to the gasification zone (32), reacts with char to generate product gases. Solar energy supplies the energy for the endothermic steam-char reaction. The hot product gases (38) flow from the gasification zone (32) to the pyrolysis zone (34) to generate hot char. Gases (38) are withdrawn from the pyrolysis zone (34) and reinjected into the region of the reactor adjacent the gasification zone (32). This eliminates hydrocarbons in the gas by steam reformation on the hot char. The product gas (14) is withdrawn from a region of the reactor between the gasification zone (32) and the pyrolysis zone (34). The product gas will be free of tar and other hydrocarbons, and thus be suitable for use in many processes.

Coal comes clean

International Nuclear Information System (INIS)

Minchener, A.

1991-01-01

Coal's status as the dominant fuel for electricity generation is under threat because of concern over the environmental impacts of acid rain and the greenhouse effect. Sulphur dioxide and nitrogen oxides cause acid rain and carbon dioxide is the main greenhouse gas. All are produced when coal is burnt. Governments are therefore tightening the emission limits for fossil-fuel power plants. In the United Kingdom phased reductions of sulphur dioxide and nitrogen oxides emissions are planned. It will be the responsibility of the power generator to take the necessary steps to reduce the emissions. This will be done using a number of technologies which are explained and outlined briefly - flue gas desulfurization, separation of coal into high and low-sulphur coal, direct desulfurization of coal, circulating fluidised bed combustion, integrated-gasification combined cycle systems and topping cycles. All these technologies are aiming at cleaner, more efficient combustion of coal. (UK)

Application of organic geochemistry to coastal tar residues from central California

Energy Technology Data Exchange (ETDEWEB)

Kvenvolden, K.A.; Rosenbauer, R.J.; Hostettler, F.D.; Lorenson, T.D.

2000-01-01

Tar residues are common on the Monterey Bay National Marine Sanctuary. These coastal tar residues have been washed ashore and usually occur on headlands near the high-tide line. In this study, 18 coastal tar residues were collected and analyzed to determine their carbon isotopic compositions and values of selected biomarker ratios. All of the residues have very heavy ({sup 13}C-enriched) carbon isotopic compositions spanning a narrow range ({delta}{sup 13}C = {minus}22.2 to {minus}23.4{per{underscore}thousand}), and 28,30-bisnorhopane is present in all samples. These same geochemical characteristics are found in Monterey Formation oils from which the coastal tar residues were likely derived. These coastal residues could result from natural seeps or from accidental spills. Statistically the coastal tar residues can be organized into three groups, each of which may represent different spill or seep events. Seven samples of potential local representative sources for the tar residues were examined, but none could account for the coastal tars.

Study on tar generated from downdraft gasification of oil palm fronds.

Science.gov (United States)

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

Directory of Open Access Journals (Sweden)

Samson Mekbib Atnaw

2014-01-01

Full Text Available One of the most challenging issues concerning the gasification of oil palm fronds (OPF is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3 in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study.

Study on Tar Generated from Downdraft Gasification of Oil Palm Fronds

Science.gov (United States)

Atnaw, Samson Mekbib; Kueh, Soo Chuan; Sulaiman, Shaharin Anwar

2014-01-01

One of the most challenging issues concerning the gasification of oil palm fronds (OPF) is the presence of tar and particulates formed during the process considering its high volatile matter content. In this study, a tar sampling train custom built based on standard tar sampling protocols was used to quantify the gravimetric concentration of tar (g/Nm3) in syngas produced from downdraft gasification of OPF. The amount of char, ash, and solid tar produced from the gasification process was measured in order to account for the mass and carbon conversion efficiency. Elemental analysis of the char and solid tar samples was done using ultimate analysis machine, while the relative concentration of the different compounds in the liquid tar was determined making use of a liquid gas chromatography (GC) unit. Average tar concentration of 4.928 g/Nm3 and 1.923 g/Nm3 was obtained for raw gas and cleaned gas samples, respectively. Tar concentration in the raw gas sample was found to be higher compared to results for other biomass materials, which could be attributed to the higher volatile matter percentage of OPF. Average cleaning efficiency of 61% which is comparable to that of sand bed filter and venturi scrubber cleaning systems reported in the literature was obtained for the cleaning system proposed in the current study. PMID:24526899

The formation of impurities in fluidized-bed gasification of biomass, peat and coal; Epaepuhtauksien muodostuminen leijukerroskaasutuksessa

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E.; Laatikainen-Luntama, J.; Kurkela, M.; Leppaelahti, J.; Koljonen, T.; Oesch, P. [VTT Energy, Espoo (Finland); Alen, R. [Jyvaeskylae Univ. (Finland)

1996-12-01

The objective of this three-year-long project was to study the effects of different process parameters and bed materials on the formation of impurities in pressurized fluidized-bed gasification. The main emphasis of the project was focused on the formation of tars and nitrogen compounds in wood, peat and coal gasification. The aims of the research were to find out such operating conditions, where the formation of problematic high-molecular-weight tars can be minimised and to create a better understanding on the fate of fuel nitrogen in fluidized-bed gasifiers. Main part of the research was carried out in a bench-scale pressurised fluidized-bed reactor (ID 30 mm), where the effects of pressure, temperature, gas atmosphere and bed material were studied with different feedstocks. Most of the test series were carried out using the same feedstocks as earlier used in the PDU-scale fluidized-bed gasification tests of VTT (pine wood, pine bark, wheat straw, two peats, Rhenish brown coal, Polish and Illinois No.6 bituminous coals). The effects of operating parameters on the product yields (gas components, tars, char) were first studied under inert nitrogen atmosphere. The conversion of fuel nitrogen into ammonia and HCN were also determined for the different feedstocks over the different operating conditions. These studies showed that ammonia is the main fixed nitrogen compound of fluidized-bed pyrolysis with all the feedstocks studied. The conversions of fuel nitrogen into ammonia and HCN was highest with the high volatile fuels and lowest with the two hard coals. Gas atmosphere had a dramatic effect on the conversion of fuel nitrogen; much higher ammonia yields were determined in real gasification gas atmosphere than in inert pyrolysis carried out in N{sub 2} or Argon atmosphere. In addition to the pressurised fluidized-bed pyrolysis tests, laboratory scale pyrolysis research was carried out in order to compare the pyrolysis behaviour of the different feedstocks

Development of clean soil technology using coals as oily/tarry contaminant removal

International Nuclear Information System (INIS)

Ignasiak, T.; Szymocha, K.; Carson, D.; Ignasiak, B.

1991-01-01

A Clean Soil Process for the treatment of oil/tar contaminated soils has been developed. The mechanics, of the clean-up process that utilizes coal as a cleaning medium is described. The experience and results obtained in the batch-scale testing as well as in the 250 kg/hr continuous facility have been applied for a conceptual design of a 200 t/day mobile plant

Human hair follicle benzo(a)pyrene and benzo(a)pyrene 7, 8-diol metabolism: effect of exposure to a coal tar-containing shampoo

Energy Technology Data Exchange (ETDEWEB)

Merk, H.F.; Mukhtar, H.; Kaufmann, I.; Das, M.; Bickers, D.R.

1987-01-01

Hair follicles are a readily available source of human epithelial tissue and offer an excellent system with which to study carcinogen metabolism in human populations. In this study hair follicles were employed to measure the metabolism of benzo(a)pyrene (BP), benzo(a)pyrene - 7,8-diol (BP 7,8-diol) and the enzyme mediated binding of /sup 3/H-BP to DNA. The effect of human exposure to a crude coal tar (CCT) - containing shampoo, a preparation rich in polycyclic aromatic hydrocarbons (PAHs on these parameters was also evaluated. It was found that aryl hydrocarbon hydroxylase (AHH) activity increased after use of the shampoo and enhancement of enzyme-mediated binding of BP to DNA was detected in most subjects. Hair follicles were shown to convert BP to several metabolic species and BP, 7,8-diol was also metabolised. Clotrimazole, a known inhibitor of the metabolism of BP was found to inhibit AHH and the metabolism of BP and BP 7,8-diol in human hair follicles, as were other imidazole compounds. The studies show that hair follicles represent an accessible tissue suitable for assessing the extent of PAH carcinogen metabolism in human subjects. Furthermore enzyme activity critical to cancer induction by PAHs was shown to be inducible following the use of a CCT-containing shampoo. Imidazole compounds were shown to be possible effective anti-carcinogens in human populations. 29 refs.

Native legume establishment on acidic coal mining overburden at Collie, Western Australia

Energy Technology Data Exchange (ETDEWEB)

Koch, J M; Bell, D T

1985-12-01

Nitrogen is often provided to impoverished overburden dumps through the establishment of legumes. Low indigenous soil nutrient levels, summer drought conditions and an acidic mining overburden represent major obstacles to successful rehabilitation of open-cut coal mining at Collie in southwest Western Australia. In this study, Acacia pulchella, a native Western Australian species often used in rehabilitation of mined lands, was shown to nodulate and grow in coal mining overburden with pH values less than 4.0 under glasshouse conditions. Plant growth (both top and root dry weight), nodule fresh weight, and nodulation success was best at pH near 5.0, a value only slightly lower than the typical soil pH of the native jarrah (Eucalyptus marginata) forest. Acetylene reduction rates were reduced by acidity and ranged from 8.2..mu..m C/sub 2/H/sub 4//g hr at pH 6.77 to 3.0..mu..m C/sub 2/H/sub 4//g hr at a pH of 3.98. Four additional plant species were found to occur and to nodulate on acid overburden material at Collie. 20 references.

Coal combustion products: trash or treasure?

Energy Technology Data Exchange (ETDEWEB)

Hansen, T.

2006-07-15

Coal combustion by-products can be a valuable resource to various industries. The American Coal Ash Association (ACAA) collects data on production and uses of coal combustion products (CCPs). 122.5 million tons of CCPs were produced in 2004. The article discusses the results of the ACCA's 2004 survey. Fly ash is predominantly used as a substitute for Portland cement; bottom ash for structural fill, embankments and paved road cases. Synthetic gypsum from the FGD process is commonly used in wallboard. Plant owners are only likely to have a buyer for a portion of their CCPs. Although sale of hot water (from Antelope Valley Station) from condensers for use in a fish farm to raise tilapia proved unviable, the Great Plains Synfuels Plant which manufactures natural gas from lignite produces a wide range of products including anhydrous ammonia, phenol, krypton, carbon dioxide (for enhanced oil recovery), tar oils and liquid nitrogen. ACCA's goal is to educate people about CCPs and how to make them into useful products, and market them, in order to reduce waste disposal and enhance revenue. The article lists members of the ACCA. 2 photos., 1 tab.

Mine Water Treatment in Hongai Coal Mines

Science.gov (United States)

Dang, Phuong Thao; Dang, Vu Chi

2018-03-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

UTILIZATION OF AQUEOUS-TAR CONDENSATES FORMED DURING GASIFICATION

Directory of Open Access Journals (Sweden)

Anna Kwiecińska

2016-11-01

Full Text Available Gasification of solid fuels is an alternative process for energy production using conventional and renewable fuels. Apart from desired compounds, i.e. carbon oxide, hydrogen and methane, the produced gas contains complex organic (tars and inorganic (carbonizate, ammonia contaminants. Those substances, together with water vapor, condensate during cooling of the process gas, what results in the formation of aqueous-tar condensate, which requires proper methods of utilization. The management of this stream is crucial for commercialization and application of the gasification technology. In the paper the treatment of aqueous-tar condensates formed during biomass gasification process is discussed. The removal of tars from the stream was based on their spontaneous separation. The aqueous stream was subjected to ultrafiltration operated at different pressures. Such a treatment configuration enabled to obtain highly concentrated retentate, which could be recycled to the gasifier, and filtrate, which could be subjected to further treatment.

The effects of pretreatment and the addition of polar compounds on the production of 'HyperCoal' from subbituminous coals

Energy Technology Data Exchange (ETDEWEB)

Kensuke Masaki; Takahiro Yoshida; Chunqi Li; Toshimasa Takanohashi; Ikuo Saito [National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba (Japan). Institute for Energy Utilization

2004-08-01

The effects of acid and hydrothermal pretreatments and the addition of polar compounds on the production of ashless-coal (HyperCoal) from subbituminous coals using cost-effective industrial solvents were investigated. The extraction yield of Wyodak subbituminous coal (C%, 75.0%) using crude methylnaphthalene oil (CMNO) at 360{sup o}C was increased significantly by 19% following acid pretreatment; it was 41.3% for the raw coal and 60.5% for the acid-treated coal. The addition of strongly polar compounds, such as N-methyl-2-pyrrolidinone (NMP), also increased the extraction yields. For Pasir subbituminous coal (%, 73.0%) the yield increased by 10% from 54.3% for the raw coal to 64.2% when 20% NMP was added to CMNO. The highest extraction yield of 72.2% was obtained for acid-treated Wyodak coal using CMNO with 20% NMP added. The ash content in HyperCoal tended to decrease following acid pretreatment and was less than 200 ppm in some coals. Hydrothermal pretreatment had a negative effect on the thermal extraction at 360{sup o}C, but increased the yield at extraction temperatures below 200{sup o}C. 20 refs., 7 figs., 2 tabs.

Evaluation of lignite tar

Energy Technology Data Exchange (ETDEWEB)

Gossedin, A

1946-01-01

Tar from the low-temperature (450/sup 0/) carbonization of lignite from Bouches-du-Rhone was hydrogenated in the presence of a catalyst based on MoS/sub 2/ with a 3:1 H:N mixture. Processing (at 470/sup 0/ and 400 atmospheres) for maximum production of gasoline yielded 86 wt % of a product of boiling 55 to 186/sup 0/ and motor octane number 75. An alternative is to hydrogenate with a view to producing solvents and lubricants. For this purpose the tar was separated by distillation (at 20 millimeters, cutting at 220/sup 0/) into two fractions of equal volume. On hydrogenation (at 300/sup 0/ and 400 atmospheres) the light part yields a gasoline H/sub 2/O-soluble cut, a highly aromatic solvent fraction, a heavier cut (280/sup 0/ to 320/sup 0/) suitable as a plasticizer, and a phenol fraction. The heavier part of the tar is hydrogenated (at 380/sup 0/ and 400 atmospheres) to give spindle oil and lubricating oil of medium eta (11.2 centistokes at 98.2/sup 0/), moderate eta index (64), good pour point (-7/sup 0/), and good oxidizing characteristics. The overall yield of products from the two portions is 86.9% (gasoline and solvent 32, light phenols 9.7, spindle oil 14.2, medium lubricating oil 25.7, wax, 5.3%).

Modeling Tar Recirculation in Biomass Fluidized Bed Gasification

NARCIS (Netherlands)

Heineken, Wolfram; De la Cuesta de Cal, Daniel; Zobel, Nico

2016-01-01

A biomass gasification model is proposed and applied to investigate the benefits of tar recirculation within a gasification plant. In the model, tar is represented by the four species phenol, toluene, naphthalene, and benzene. The model is spatially one-dimensional, assuming plug flow for the

Thermal processing of Khoot coal and characterization of obtained solid and liquid products

Directory of Open Access Journals (Sweden)

S Batbileg

2014-12-01

Full Text Available On 21st January 2015, the abstract of this paper was replaced with the correct abstract.The coal of Khoot deposit have been investigated and determined the technical characteristics, elemental and petrographical maceral compositions. On the basis of proximate, ultimate, petrographic and IR analysis results have been confirmed that the Khoot coal is a sub-bituminous coal. The hard residue after pyrolysis have been activated by heated water steam and determined the iodine and methylene blue adsorption of initial coal and activated carbon samples from pyrolysis hard residue. The porosity structure of initial coal, activated carbon of pyrolysis hard residue and hard residue after thermolysis (thermal dissolution have been determined by SEM analysis. The liquid tar product of thermolysis of Khoot coal was investigated by FTIR, 13C and 1H NMR spectrometric analysis. The results of thermolysis of Khoot coal in tetralin with constant mass ratio between coal and tetralin (1:1.8 at 450°C show that 60.8% of liquid product can be obtained after thermolysis of the coal organic mass.DOI: http://doi.dx.org/10.5564/mjc.v15i0.326 Mongolian Journal of Chemistry 15 (41, 2014, p66-72

17,21-Secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids in source rocks and crude oils

Energy Technology Data Exchange (ETDEWEB)

Xueming Pan; Philp, R.P. [University of Oklahoma, Norman, OK (United States). School of Geology and Geophysics

2006-09-15

The presence of three families of hopanoic acids, 17,21-secohopanoic acids, 25-norhopanoic acids, and 28-norhopanoic acids, is discussed. Oils from West Siberia and tar balls from the Seychelles Islands were found to contain relatively high proportions of 17,21-secohopanoic acids. These acids have not been previously reported in any oils or source rocks. A heavily biodegraded West Siberian oil, was found to contain an homologous series of 25-norhopanoic acids co-occurring with the 25-norhopanes as previously reported in only a small number of oils from Campos Basin, Brazil. 28-Norhopanoic acids have been reported in various sediments and extracts of the Monterey Shale, but in this study their occurrence has been extended to oils, degraded oils, and tar balls sourced from the Monterey Shale. The primary purpose herein is to report the occurrence of these acids and possible relationships between the acids and corresponding hydrocarbons. (Author)

The fate of injectant coal in blast furnaces: The origin of extractable materials of high molecular mass in blast furnace carryover dusts

Energy Technology Data Exchange (ETDEWEB)

Dong, S.N.; Wu, L.; Paterson, N.; Herod, A.A.; Dugwell, D.R.; Kandiyoti, R. [University of London Imperial College of Science & Technology, London (United Kingdom). Dept. of Chemical Engineering

2005-07-01

The aim of the work was to investigate the fate of injectant coal in blast furnaces and the origin of extractable materials in blast furnace carryover dusts. Two sets of samples including injectant coal and the corresponding carryover dusts from a full sized blast furnace and a pilot scale rig have been examined. The samples were extracted using 1-methyl-2-pyrrolidinone (NMP) solvent and the extracts studied by size exclusion chromatography (SEC). The blast furnace carryover dust extracts contained high molecular weight carbonaceous material, of apparent mass corresponding to 10{sup 7}-10{sup 8} u, by polystyrene calibration. In contrast, the feed coke and char prepared in a wire mesh reactor under high temperature conditions did not give any extractable material. Meanwhile, controlled combustion experiments in a high-pressure wire mesh reactor suggest that the extent of combustion of injectant coal in the blast furnace tuyeres and raceways is limited by time of exposure and very low oxygen concentration. It is thus likely that the extractable, soot-like material in the blast furnace dust originated in tars is released by the injectant coal. Our results suggest that the unburned tars were thermally altered during the upward path within the furnace, giving rise to the formation of heavy molecular weight (soot-like) materials.

1170-MW(t) HTGR-PS/C plant application study report: tar sands oil recovery application

International Nuclear Information System (INIS)

Rao, R.; McMain, A.T. Jr.

1981-05-01

This report summarizes a study to apply an 1170-MW(t) high-temperature gas-cooled reactor - process steam/cogeneration (HTGR-PS/C) to tar sands oil recovery and upgrading. The raw product recovered from the sands is a heavy, sour bitumen; upgrading, which involves coking and hydrodesulfurization, produces a synthetic crude (refinable by current technology) and petroleum coke. Steam and electric power are required for the recovery and upgrading process. Proposed and commercial plants would purchase electric power from local utilities and obtain from boilers fired with coal and with by-product fuels produced by the upgrading. This study shows that an HTGR-PS/C represents a more economical source of steam and electric power

Coal surface control for advanced physical fine coal cleaning technologies

Energy Technology Data Exchange (ETDEWEB)

Morsi, B.I.; Chiang, S.H.; Sharkey, A.; Blachere, J.; Klinzing, G.; Araujo, G.; Cheng, Y.S.; Gray, R.; Streeter, R.; Bi, H.; Campbell, P.; Chiarlli, P.; Ciocco, M.; Hittle, L.; Kim, S.; Kim, Y.; Perez, L.; Venkatadri, R.

1992-01-01

This final report presents the research work carried out on the Coal Surface Control for Advanced Physical Fine Coal Cleaning Technologies project, sponsored by the US Department of Energy, Pittsburgh Energy Technology Center (DOE/PETC). The project was to support the engineering development of the selective agglomeration technology in order to reduce the sulfur content of US coals for controlling SO[sub 2] emissions (i.e., acid rain precursors). The overall effort was a part of the DOE/PETCs Acid Rain Control Initiative (ARCI). The overall objective of the project is to develop techniques for coal surface control prior to the advanced physical fine coal cleaning process of selective agglomeration in order to achieve 85% pyrite sulfur rejection at an energy recovery greater than 85% based on run-of-mine coal. The surface control is meant to encompass surface modification during grinding and laboratory beneficiation testing. The project includes the following tasks: Project planning; methods for analysis of samples; development of standard beneficiation test; grinding studies; modification of particle surface; and exploratory R D and support. The coal samples used in this project include three base coals, Upper Freeport - Indiana County, PA, Pittsburgh NO. 8 - Belmont County, OH, and Illinois No. 6 - Randolph County, IL, and three additional coals, Upper Freeport - Grant County- WV, Kentucky No. 9 Hopkins County, KY, and Wyodak - Campbell County, WY. A total of 149 drums of coal were received.

Study of environmental pollution and mineralogical characterization of sediment rivers from Brazilian coal mining acid drainage

Energy Technology Data Exchange (ETDEWEB)

Silva, Luis F.O., E-mail: felipeqma@hotmail.com [Environmental Science and Nanotechnology Department, Institute of Environmental Research and Human Development – IPADH, Capivari de Baixo, Santa Catarina (Brazil); Laboratory of Environmental Researches and Nanotechnology Development, Centro Universitário La Salle, Victor Barreto, 2288 Centro 92010-000, Canoas, RS (Brazil); Fdez- Ortiz de Vallejuelo, Silvia; Martinez-Arkarazo, Irantzu; Castro, Kepa [Department of Analytical Chemistry, University of the Basque Country (EHU/UPV), P.O. Box 644, 48080 Bilbao, Basque Country (Spain); Oliveira, Marcos L.S. [Environmental Science and Nanotechnology Department, Institute of Environmental Research and Human Development – IPADH, Capivari de Baixo, Santa Catarina (Brazil); Sampaio, Carlos H.; Brum, Irineu A.S. de [Universidade Federal do Rio Grande do Sul, Escola de Engenharia, Departamento de Metalurgia, Centro de Tecnologia, Av. Bento Gonçalves, 9500, Bairro Agronomia, CEP: 91501-970, Porto Alegre, RS (Brazil); Leão, Felipe B. de; Taffarel, Silvio R. [Laboratory of Environmental Researches and Nanotechnology Development, Centro Universitário La Salle, Victor Barreto, 2288 Centro 92010-000, Canoas, RS (Brazil); Madariaga, Juan M. [Department of Analytical Chemistry, University of the Basque Country (EHU/UPV), P.O. Box 644, 48080 Bilbao, Basque Country (Spain)

2013-03-01

Acid drainage from coal mines and metal mining is a major source of underground and surface water contamination in the world. The coal mining acid drainage (CMAD) from mine contains large amount of solids in suspension and a high content of sulphate and dissolved metals (Al, Mn, Zn, Cu, Pb, Fe, etc.) that finally are deposited in the rivers. Since this problem can persist for centuries after mine abandonment, it is necessary to apply multidisciplinary methods to determine the potential risk in a determinate area. These multidisciplinary methods must include molecular and elemental analysis and finally all information must be studied statistically. This methodology was used in the case of coal mining acid drainage from the Tubarao River (Santa Catarina, Brazil). During molecular analysis, Raman Spectroscopy, electron bean, and X-ray diffraction (XRD) have been proven very useful for the study of minerals present in sediment rivers near this CMAD. The obtained spectra allow the precise identification of the minerals as jarosite, quartz, clays, etc. The elemental analysis (Al, As, Fe, K, Na, Ba, Mg, Mn, Ti, V, Zn, Ag, Co, Li, Mo, Ni, Se, Sn, W, B, Cr, Cu, Pb and Sr) was realised by inductively coupled plasma mass spectrometry (ICP-MS). Statistical analysis (Principal Component Analysis) of these dates of concentration reveals the existence of different groups of samples with specific pollution profiles in different areas of the Tubarao River. Highlights: ► Increasing coal drainage sediments geochemical information will increase human health information in this area. ► Brazilian coal mining information will increase recuperation planning information. ► The nanominerals showed strong sorption ability to aqueous hazardous elements.

Study of environmental pollution and mineralogical characterization of sediment rivers from Brazilian coal mining acid drainage

International Nuclear Information System (INIS)

Silva, Luis F.O.; Fdez- Ortiz de Vallejuelo, Silvia; Martinez-Arkarazo, Irantzu; Castro, Kepa; Oliveira, Marcos L.S.; Sampaio, Carlos H.; Brum, Irineu A.S. de; Leão, Felipe B. de; Taffarel, Silvio R.; Madariaga, Juan M.

2013-01-01

Acid drainage from coal mines and metal mining is a major source of underground and surface water contamination in the world. The coal mining acid drainage (CMAD) from mine contains large amount of solids in suspension and a high content of sulphate and dissolved metals (Al, Mn, Zn, Cu, Pb, Fe, etc.) that finally are deposited in the rivers. Since this problem can persist for centuries after mine abandonment, it is necessary to apply multidisciplinary methods to determine the potential risk in a determinate area. These multidisciplinary methods must include molecular and elemental analysis and finally all information must be studied statistically. This methodology was used in the case of coal mining acid drainage from the Tubarao River (Santa Catarina, Brazil). During molecular analysis, Raman Spectroscopy, electron bean, and X-ray diffraction (XRD) have been proven very useful for the study of minerals present in sediment rivers near this CMAD. The obtained spectra allow the precise identification of the minerals as jarosite, quartz, clays, etc. The elemental analysis (Al, As, Fe, K, Na, Ba, Mg, Mn, Ti, V, Zn, Ag, Co, Li, Mo, Ni, Se, Sn, W, B, Cr, Cu, Pb and Sr) was realised by inductively coupled plasma mass spectrometry (ICP-MS). Statistical analysis (Principal Component Analysis) of these dates of concentration reveals the existence of different groups of samples with specific pollution profiles in different areas of the Tubarao River. Highlights: ► Increasing coal drainage sediments geochemical information will increase human health information in this area. ► Brazilian coal mining information will increase recuperation planning information. ► The nanominerals showed strong sorption ability to aqueous hazardous elements

Mine Water Treatment in Hongai Coal Mines

Directory of Open Access Journals (Sweden)

Dang Phuong Thao

2018-01-01

Full Text Available Acid mine drainage (AMD is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

48 CFR Appendix to Part 1252 - Tar Matrix

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Tar Matrix Appendix to Part 1252 Federal Acquisition Regulations System DEPARTMENT OF TRANSPORTATION CLAUSES AND FORMS SOLICITATION PROVISIONS AND CONTRACT CLAUSES Pt. 1252, App. Appendix to Part 1252—Tar Matrix ER27DE05.000...

Seventh symposium on coal mine drainage research. NCA/BCR coal conference and Expo IV

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

The Seventh Symposium on Coal Mine Drainage Research, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Seventeen papers from the proceedings have been entered individually into EDB and ERA. Topics covered include chemical reactions of pyrite oxidation and acid formation in spoil banks, abandoned mines, etc., formation of small acid lakes from the drainage and their neutralization by natural and other neutralization measures, trace elements in acid mine drainage, ground water contamination, limnology, effects of surface mined ground reclamation and neutralization, water purification and treatment, mining and coal preparation plant waste disposal, ash and fly ash disposal (to minimize leaching from the wastes), runoff from large coal storage stockpiles during storms (prevention of environmental effects by collection and neutralization by passing through an ash pond). (LTN)

Low severity conversion of activated coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Hirschon, A.S.; Ross, D.S.

1990-01-01

The results suggest that coal contains regions with structural components significantly reactive under the hydrothermal environment. Although the specific mechanism for this process remains to be developed, this activity is reminiscent of findings in studies of accelerated maturation of oil shale, where hydrothermal treatment (hydrous pyrolysis) leads to the production of petroleum hydrocarbons. In line with what has been seen in the oil shale work, the pretreatment-generated hydrocarbons and phenols appear to represent a further or more complete maturation of some fraction of the organic material within the coal. These observations could have an impact in two areas. The first is in the area of coal structure, where immature, reactive regions have not been included in the structures considered at present. The second area of interest is the more practical one of conversions to coal liquids and pyrolytic tars. It seems clear that the hydrothermal pretreatment changes the coal in some manner that favorably affects the product quality substantially and, as in the CO/water liquefaction case, favorably affects the yields. The conversions of coals of lower rank, i.e., less mature coals, could particularly benefit in terms of both product quality and product quantity. The second portion of this project also shows important benefits to coal conversion technology. It deals with synthesizing catalysts designed to cleave the weak links in the coal structure and then linking these catalysts with the pretreatment methods in Task 2. The results show that highly dispersed catalysts can effectively be used to increase the yields of soluble material. An important aspect of highly dispersed catalysts are that they can effectively catalyze coal conversion even in poor liquefaction solvents, thus making them very attractive in processes such as coprocessing where inexpensive liquefaction media such as resids are used.

Low-temperature carbonization of bituminous coal for the production of solid, liquid, and gaseous fuels

Energy Technology Data Exchange (ETDEWEB)

1942-01-01

Properties and uses of low-temperature coke for producing ferrosilicon, CaC/sub 2/ generator gas and water gas, as a fuel for boilers and household use and as a diluent for coking coal, and the properties and uses of low-temperature tar, gasoline, gas, and liquefied gas are described. By using a circulating gas, it is possible to obtain in low-temperature carbonization of bituminous coal a fuel oil for the navy. Aging-test data of such an oil are given. Several plants in Upper Silesia, using the Lurgi circulation process are producing a fuel oil that meets specification.

Evaluation of Gravimetric Tar Determination in Particle Samples

DEFF Research Database (Denmark)

Hindsgaul, Claus; Henriksen, Ulrik B.; Bentzen, Jens Dall

2000-01-01

A comparison of tar determination of particles from a down-draft gasifier using soxhlet extractions (with anisole, dichloromethane and acetone) and pyrolysis of the particles.......A comparison of tar determination of particles from a down-draft gasifier using soxhlet extractions (with anisole, dichloromethane and acetone) and pyrolysis of the particles....

Coal-water slurries containing petrochemicals to solve problems of air pollution by coal thermal power stations and boiler plants: An introductory review.

Science.gov (United States)

Dmitrienko, Margarita A; Strizhak, Pavel A

2018-02-01

This introductory study presents the analysis of the environmental, economic and energy performance indicators of burning high-potential coal water slurries containing petrochemicals (CWSP) instead of coal, fuel oil, and natural gas at typical thermal power stations (TPS) and a boiler plant. We focus on the most hazardous anthropogenic emissions of coal power industry: sulfur and nitrogen oxides. The research findings show that these emissions may be several times lower if coal and oil processing wastes are mixed with water as compared to the combustion of traditional pulverized coal, even of high grades. The study focuses on wastes, such as filter cakes, oil sludge, waste industrial oils, heavy coal-tar products, resins, etc., that are produced and stored in abundance. Their deep conversion is very rare due to low economic benefit. Effective ways are necessary to recover such industrial wastes. We present the cost assessment of the changes to the heat and power generation technologies that are required from typical power plants for switching from coal, fuel oil and natural gas to CWSPs based on coal and oil processing wastes. The corresponding technological changes pay off after a short time, ranging from several months to several years. The most promising components for CWSP production have been identified, which provide payback within a year. Among these are filter cakes (coal processing wastes), which are produced as a ready-made coal-water slurry fuel (a mixture of flocculants, water, and fine coal dust). These fuels have the least impact on the environment in terms of the emissions of sulfur and nitrogen oxides as well as fly ash. An important conclusion of the study is that using CWSPs based on filter cakes is worthwhile both as the main fuel for thermal power stations and boiler plants and as starting fuel. Copyright © 2017 Elsevier B.V. All rights reserved.

Mine Water Treatment in Hongai Coal Mines

OpenAIRE

Dang Phuong Thao; Dang Vu Chi

2018-01-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine ...

National Coal Board Medical Service annual report 1980-1981

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

Sections report on: medical examinations and consultations; protection from health hazards such as pneumoconiosis and other prescribed diseases; problems such as vitamin D in the blood of miners, Legionaires' disease, Perthe's disease, rehabilitation and physiotherapy, chemical hazards, public health and hygiene, noise, and the use of visual display units; diseases from coal products such as in coke and tar manufacture; first aid services, morphia, and nursing service; and back pain in the mining industry. A list of staff and their publications is also included.

Experimental comparison of biomass chars with other catalysts for tar reduction

NARCIS (Netherlands)

Abu El-Rub, Ziad; Bramer, Eduard A.; Brem, Gerrit

2008-01-01

In this paper the potential of using biomass char as a catalyst for tar reduction is discussed. Biomass char is compared with other known catalysts used for tar conversion. Model tar compounds, phenol and naphthalene, were used to test char and other catalysts. Tests were carried out in a fixed bed

Report for the coal type committee in fiscal 1992; 1992 nendo tanshu iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the coal type committee in fiscal 1992, and summarizes the main technological achievements. In the Chinese coal liquefaction test, fiscal 1991 has performed liquefaction tests on Fushun coal by using a small continuous testing facility (0.1 t/d) at the Coal Chemistry Research Institute in Beijing. Fiscal 1992 has completed the liquefaction tests on Shengli coal. In October, a liquefaction test was carried out by using Tianzhu coal according to the NEDOL process. This paper reports the result of the liquefaction test on the Shengli coal, and the result of the analysis on the Fushun coal liquefied oil. The coal type selection and investigation having been performed to date reveals close correlation among the maceral composition of coal, coal rank and liquefied oil yield. Coals having good reactivity and suitable for liquefaction are generally suitable also for gasification. In the pretreatment of coal as a gasification material for hydrogen manufacture, a test was performed by using A heavy oil and tar sand bitumen plus A heavy oil as the granulating agents. With Montana coal, the highest de-ashing rate was achieved when the oil was added at 35% by weight. Both of the reaction rate and oil yield were improved. A handling test was carried out up to 72.5 degrees C, wherein Tatung coal presented no problems in both of the discharging and sticking tendencies. (NEDO)

Oxidizing oils, etc. [British patent

Energy Technology Data Exchange (ETDEWEB)

Penniman, W B.D.

1926-03-02

The oxidation of crude petroleum and its distillates, shale oils and tars, waxes, sludges, petroleum residues, asphaltic oils, asphalt, malthas, cracked oils and residues from cracking stills, wood tar oils and wood tar, peat and lignite distillates, coal tar oils and coal tar, and oils containing powdered coal, coke or peat, sulphur in suspension, is effected by passing air or other oxygen-containig gas through a layer of the material of a depth sufficient substantially to deoxygenate the air, the pressure being at or below atmospheric pressure.

Reactivities of acid and/or tetralin pretreated Wandoan coal for a Curie point flash pyrolysis; Sanzen shori, tetralin yobaimae shori Wandoan tan no kyusoku netsubunkai

Energy Technology Data Exchange (ETDEWEB)

Kishino, M.; Sakanishi, K.; Korai, Y.; Mochida, I. [Kyushu University, Fukuoka (Japan). Institute of Advanced Material Study

1996-10-28

Discussions were given on effects of acid pretreatment and tetralin swelling in Wandoan coal on a Curie point flash pyrolysis (which used a Curie point pyrolyzer). Residue yield loss effects were obtained at 3.9% in hydrochloric acid pretreatment, and 6.2% in acetic acid pretreatment. The effects of tetralin swelling pretreatment were compared in the similar manner in terms of the residue yield loss. The effects were 4.0% in untreated coal, 2.0% in the hydrochloric acid pretreatment, and 0.6% in the acetic acid pretreatment. It is thought that components that can be activated by acetic acid have already been activated, but the remaining components would not be activated by tetralin. Average microporosity (area) in the remaining particle as a whole shows very little difference both in acetic acid pretreated coal and untreated coal. However, with the acetic acid pretreatment, pores smaller than 4{mu}m{sup 2} disappeared, and pores as large as 205 to 411{mu}m{sup 2} increased largely. This phenomenon was observed as an increase in foaming degree under microscopic observation, even if the average microporosity remains equal. Thermoplasticity of the coal increased, and so did volatilization reactivity as a result of the acetic acid pretreatment, resulting in appearance of a large number of large pores. 6 refs., 2 figs., 2 tabs.

Pressurised fluidised-bed gasification experiments with biomass, peat and coal at VTT in 1991-1994. Gasification of Danish wheat, straw and coal

Energy Technology Data Exchange (ETDEWEB)

Kurkela, E; Laatikainen-Luntama, J; Staahlberg, P; Moilanen, A [VTT Energy, Espoo (Finland). Energy Production Technologies

1997-12-31

Fluidised-bed air gasification of three different Danish straw feedstocks and Colombian bituminous coal was studied in the PDU-scale test facilities of VTT. The test programme was divided into two different modes of operation. First, the usability of straw as the only feedstock was investigated by operating the gasifier at relatively low temperature normally used in biomass gasifiers. In this operation mode the main aim was to find out the limits for gasification temperatures, set by the sintering behaviour of the straw. Secondly, the use of straw as an additional feedstock in a fluidised-bed coal gasifier was examined by operating the gasifier at about 1 000 deg C with different ratings of straw and coal feeding. The gasifier was operated at 5 bar pressure and at 80 990 deg C. The product gas was cleaned by ceramic candle filters operated at 465-540 deg C. Concentrations of tars, nitrogen com- pounds, sulphur gases, vapour-phase alkali metals as well as chlorine were determined in different operating conditions. (12 refs.)

Athabasca tar sand reservoir properties derived from cores and logs

International Nuclear Information System (INIS)

Woodhouse, R.

1976-01-01

Log interpretation parameters for the Athabasca Tar Sand Lease No. 24 have been determined by careful correlation with Dean and Stark core analysis data. Significant expansion of Athabasca cores occurs as overburden pressure is removed. In the more shaly sands the core analysis procedures remove adsorbed water from the clays leading to further overestimation of porosity and free water volume. Log interpretation parameters (R/sub w/ = 0.5 ohm . m and m = n = 1.5) were defined by correlation with the weight of tar as a fraction of the weight of rock solids (grain or dry weight fraction of tar). This quantity is independent of the water content of the cores, whereas porosity and the weight of tar as a fraction of the bulk weight of fluids plus solids (bulk weight fraction) are both dependent on water content. Charts are provided for the conversion of bulk weight fraction of fluids to porosity; grain weight fraction of fluids to porosity; log derived porosity and core grain weight tar to water saturation. Example results show that the core analysis grain weight fraction of tar is adequately matched by the log analyses. The log results provide a better representation of the reservoir fluid volumes than the core analysis data

Coal preparation

International Nuclear Information System (INIS)

Anon.

1991-01-01

The acid rain control legislation has prompted the Department of Energy (DOE) to seek new technology using the Clean Coal Technology program solicitation. The main goal of the program is to reduce SO 2 emissions below 9 Mt/a (10 million stpy) and NO x emission below 5.4 Mt/a (6 million stpy) by the year 2000. This would be accomplished by using precombustion, combustion, post combustion and conversion technology. Utilities are considering installing new scrubbers, switching fuel or possibly deep clean. However, the time required to implement the control technology is short. Due to the legislation, about 110 plants will have to adopt one of the approaches. This paper reports that in characterization of coal, Ames Laboratory used a scanning electron microscope- based, automated image analysis (SEM-AIA) technique to identify coal and mineral matter association. Various forms of organic sulfur were identified using peroxyacetic acid oxidation of coal. This was followed by subsequent microscopic, GC-MS, and HRMS analysis by Southern Illinois University. In ultrafine grinding of coal, it was reported by the Mining and Mineral Institute of Alabama that silica sand or flint shot used less energy compared to steel ball mills

Prediction of acid mine drainage generation potential of various lithologies using static tests: Etili coal mine (NW Turkey) as a case study.

Science.gov (United States)

Yucel, Deniz Sanliyuksel; Baba, Alper

2016-08-01

The Etili neighborhood in Can County (northwestern Turkey) has large reserves of coal and has been the site of many small- to medium-scale mining operations since the 1980s. Some of these have ceased working while others continue to operate. Once activities cease, the mining facilities and fields are usually abandoned without rehabilitation. The most significant environmental problem is acid mine drainage (AMD). This study was carried out to determine the acid generation potential of various lithological units in the Etili coal mine using static test methods. Seventeen samples were selected from areas with high acidic water concentrations: from different alteration zones belonging to volcanic rocks, from sedimentary rocks, and from coals and mine wastes. Static tests (paste pH, standard acid-base accounting, and net acid generation tests) were performed on these samples. The consistency of the static test results showed that oxidation of sulfide minerals, especially pyrite-which is widely found not only in the alteration zones of volcanic rocks but also in the coals and mine wastes-is the main factor controlling the generation of AMD in this mine. Lack of carbonate minerals in the region also increases the occurrence of AMD.

Bacteria and Acidic Drainage from Coal Refuse: Inhibition by Sodium Lauryl Sulfate and Sodium Benzoate

OpenAIRE

Dugan, Patrick R.; Apel, William A.

1983-01-01

The application of an aqueous solution of sodium lauryl sulfate and sodium benzoate to the surface of high-sulfur coal refuse resulted in the inhibition of iron-and sulfur-oxidizing chemoautotrophic bacteria and in the decrease of acidic drainage from the refuse, suggesting that acid drainage can be abated in the field by inhibiting iron- and sulfur-oxidizing bacteria.

Dry sorbent injection of trona to control acid gases from a pilot-scale coal-fired combustion facility

Directory of Open Access Journals (Sweden)

Tiffany L. B. Yelverton

2016-01-01

Full Text Available  Gaseous and particulate emissions from the combustion of coal have been associated with adverse effects on human and environmental health, and have for that reason been subject to regulation by federal and state governments. Recent regulations by the United States Environmental Protection Agency have further restricted the emissions of acid gases from electricity generating facilities and other industrial facilities, and upcoming deadlines are forcing industry to consider both pre- and post-combustion controls to maintain compliance. As a result of these recent regulations, dry sorbent injection of trona to remove acid gas emissions (e.g. HCl, SO2, and NOx from coal combustion, specifically 90% removal of HCl, was the focus of the current investigation. Along with the measurement of HCl, SO2, and NOx, measurements of particulate matter (PM, elemental (EC, and organic carbon (OC were also accomplished on a pilot-scale coal-fired combustion facility. Gaseous and particulate emissions from a coal-fired combustor burning bituminous coal and using dry sorbent injection were the focus of the current study. From this investigation it was shown that high levels of trona were needed to achieve the goal of 90% HCl removal, but with this increased level of trona injection the ESP and BH were still able to achieve greater than 95% fine PM control. In addition to emissions reported, measurement of acid gases by standard EPA methods were compared to those of an infrared multi-component gas analyzer. This comparison revealed good correlation for emissions of HCl and SO2, but poor correlation in the measurement of NOx emissions.

Clean coal technology: The new coal era

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The Clean Coal Technology Program is a government and industry cofunded effort to demonstrate a new generation of innovative coal processes in a series of full-scale showcase`` facilities built across the country. Begun in 1986 and expanded in 1987, the program is expected to finance more than $6.8 billion of projects. Nearly two-thirds of the funding will come from the private sector, well above the 50 percent industry co-funding expected when the program began. The original recommendation for a multi-billion dollar clean coal demonstration program came from the US and Canadian Special Envoys on Acid Rain. In January 1986, Special Envoys Lewis and Davis presented their recommendations. Included was the call for a 5-year, $5-billion program in the US to demonstrate, at commercial scale, innovative clean coal technologies that were beginning to emerge from research programs both in the US and elsewhere in the world. As the Envoys said: if the menu of control options was expanded, and if the new options were significantly cheaper, yet highly efficient, it would be easier to formulate an acid rain control plan that would have broader public appeal.

Steam versus coking coal and the acid rain program

International Nuclear Information System (INIS)

Lange, Ian

2010-01-01

The Clean Air Act of 1990 initiated a tradable permit program for emissions of sulfur dioxide from coal-fired power plants. One effect of this policy was a large increase in the consumption of low-sulfur bituminous coal by coal-fired power plants. However, low-sulfur bituminous coal is also the ideal coking coal for steel production. The analysis presented here will attempt to determine how the market responded to the increased consumption of low-sulfur bituminous coal by the electricity generation sector. Was there a decrease in the quality and/or quantity of coking coal consumption or did extraction increase? Most evidence suggests that the market for coking coal was unaffected, even as the extraction and consumption of low-sulfur bituminous coal for electricity generation increased substantially.

Effect of water addition in a microwave assisted thermal cracking of biomass tar models

International Nuclear Information System (INIS)

Warsita, Aris; Al-attab, K.A.; Zainal, Z.A.

2017-01-01

Highlights: • Effective tar thermal treatment with water addition using microwave is proposed. • The reactor temperature of 1200 °C can be reached quickly at bed height 120 mm. • The optimum water to tar ratio W/T was 0.3 for tar models. • Temperature greatly effect tar removal at various W/T rates. - Abstract: Producer gas from biomass gasification is plagued by the presence of tar which causes pipe blockages. Thermal and catalytic treatments in a microwave reactor have been shown to be effective methods in removing tar from producer gas. A question arises as to the possibility of enhancing the removal mechanism by adding water into the reactor. Toluene and naphthalene were used as tar models in the present study with N_2 as the carrier gas followed by the use of simulated producer gas. Thermal treatment with various amount of water was added at temperatures in the range of 800–1200 °C. The tar removal efficiency obtained 95.83% at the optimum temperature of 1200 °C for naphthalene in for toluene 96.32% at 1050 °C at water to tar ratio (W/T) of 0.3. This study shows that the removal of tar by microwave irradiation with water addition is a significant and effective method in tar cracking.

Sampling of tar from sewage sludge gasification using solid phase adsorption.

Science.gov (United States)

Ortiz González, Isabel; Pérez Pastor, Rosa Ma; Sánchez Hervás, José Ma

2012-06-01

Sewage sludge is a residue from wastewater treatment plants which is considered to be harmful to the environment and all living organisms. Gasification technology is a potential source of renewable energy that converts the sewage sludge into gases that can be used to generate energy or as raw material in chemical synthesis processes. But tar produced during gasification is one of the problems for the implementation of the gasification technology. Tar can condense on pipes and filters and may cause blockage and corrosion in the engines and turbines. Consequently, to minimize tar content in syngas, the ability to quantify tar levels in process streams is essential. The aim of this work was to develop an accurate tar sampling and analysis methodology using solid phase adsorption (SPA) in order to apply it to tar sampling from sewage sludge gasification gases. Four types of commercial SPA cartridges have been tested to determine the most suitable one for the sampling of individual tar compounds in such streams. Afterwards, the capacity, breakthrough volume and sample stability of the Supelclean™ ENVI-Carb/NH(2), which is identified as the most suitable, have been determined. Basically, no significant influences from water, H(2)S or NH(3) were detected. The cartridge was used in sampling real samples, and comparable results were obtained with the present and traditional methods.

Ultrafine ash aerosols from coal combustion: Characterization and health effects

Energy Technology Data Exchange (ETDEWEB)

William P. Linak; Jong-Ik Yoo; Shirley J. Wasson; Weiyan Zhu; Jost O.L. Wendt; Frank E. Huggins; Yuanzhi Chen; Naresh Shah; Gerald P. Huffman; M. Ian Gilmour [US Environmental Protection Agency, Research Triangle Park, NC (United States). National Risk Management Research Laboratory

2007-07-01

Ultrafine coal fly-ash particles withdiameters less than 0.5 {mu}m typically comprise less than 1% of the total fly-ash mass. This paper reports research focused on both characterization and health effects of primary ultrafine coal ash aerosols alone. Ultrafine, fine, and coarse ash particles were segregated and collected from a coal burned in a 20 kW laboratory combustor and two additional coals burned in an externally heated drop tube furnace. Extracted samples from both combustors were characterized by transmission electron microscopy (TEM), wavelength dispersive X-ray fluorescence(WD-XRF) spectroscopy, Moessbauer spectroscopy, and X-ray absorption fine structure (XAFS) spectroscopy. Pulmonary inflammation was characterized by albumin concentrations in mouse lung lavage fluid after instillation of collected particles in saline solutions and a single direct inhalation exposure. Results indicate that coal ultrafine ash sometimes contains significant amounts of carbon, probably soot originating from coal tar volatiles, depending on coal type and combustion device. Surprisingly, XAFS results revealed the presence of chromium and thiophenic sulfur in the ultrafine ash particles. The instillation results suggested potential lung injury, the severity of which could be correlated with the carbon (soot) content of the ultrafines. This increased toxicity is consistent with theories in which the presence of carbon mediates transition metal (i.e., Fe) complexes, as revealed in this work by TEM and XAFS spectroscopy, promoting reactive oxygenspecies, oxidation-reduction cycling, and oxidative stress. 24 refs., 7 figs.

Co-gasification of coal and biomass: Synergy, characterization and reactivity of the residual char.

Science.gov (United States)

Hu, Junhao; Shao, Jingai; Yang, Haiping; Lin, Guiying; Chen, Yingquan; Wang, Xianhua; Zhang, Wennan; Chen, Hanping

2017-11-01

The synergy effect between coal and biomass in their co-gasification was studied in a vertical fixed bed reactor, and the physic-chemical structural characteristics and gasification reactivity of the residual char obtained from co-gasification were also investigated. The results shows that, conversion of the residual char and tar into gas is enhanced due to the synergy effect between coal and biomass. The physical structure of residual char shows more pore on coal char when more biomass is added in the co-gasification. The migration of inorganic elements between coal and biomass was found, the formation and competitive role of K 2 SiO 3 , KAlSiO 4 , and Ca 3 Al 2 (SiO 4 ) 3 is a mechanism behind the synergy. The graphization degree is enhanced but size of graphite crystallite in the residual char decreases with biomass blending ratio increasing. TGA results strongly suggest the big difference in the reactivity of chars derived from coal and biomass in spite of influence from co-gasification. Copyright © 2017 Elsevier Ltd. All rights reserved.

Co-pyrolysis of waste tire/coal mixtures for smokeless fuel, maltenes and hydrogen-rich gas production

Czech Academy of Sciences Publication Activity Database

Bičáková, Olga; Straka, Pavel

2016-01-01

Roč. 116, MAY 15 (2016), s. 203-213 ISSN 0196-8904 Grant - others:OPPK(XE) CZ.2.16/3.1.00/21538 Program:OPPK Institutional support: RVO:67985891 Keywords : waste tires * coal * co-pyrolysis * smokeless fuel * tar * hydrogen -rich gas Subject RIV: DM - Solid Waste and Recycling Impact factor: 5.589, year: 2016 http://www.sciencedirect.com/science/article/pii/S0196890416300991

Maturation related changes in the distribution of ester bound fatty acids and alcohols in a coal series from the New Zealand Coal Band covering diagenetic to catagenetic coalification levels

Energy Technology Data Exchange (ETDEWEB)

Glombitza, C.; Mangelsdorf, K.; Horsfield, B. [German Research Cemter of Geoscience GFZ, Potsdam (Germany)

2009-10-15

Several lignites and coals of low to moderate maturation levels from the New Zealand Coal Band were investigated using alkaline ester cleavage experiments to reveal compositional changes of ester bound components during increasing maturation. Ester bound alcohols are found to be present in highest amounts in the very immature lignite samples but show a rapid decrease during early diagenesis. Ester bound fatty acids also show an initial exponential decrease during diagenesis but reveal an intermittent increase during early catagenesis before decreasing again during main catagenesis. This was related to the short chain fatty acids. To obtain a maturity related signal and to eliminate facies related scattering in the amounts of fatty acids in the coal samples, the carbon preference index of fatty acids (CPIFA) parameter is introduced. For the long chain fatty acids the CPIFA decreases with increasing maturity. During diagenesis, the same trend can be observed for the short chain fatty acids but the intermittent increase in the amounts of short chain fatty acids is also accompanied by high CPIFA values. This indicates less altered organic biomass at this maturation level and is in contrast to the mature CPIFA signal of the long chain fatty acids of the same samples. Thus could be due to extremely different amounts of short and long chain fatty acids in the original source organic matter or it could due to the incorporation of immature bacterial biomass from deep microbial communities containing C{sub 16} and C{sub 18} fatty acids as main cell membrane components. Deep microbial life might be stimulated at this interval by the increasing release of thermally generated potential substrates from the organic matrix during early catagenesis. The high amounts of alcohols in the immature lignite samples are also visible in the alkene distribution from the open system pyrolysis experiments of the organic matrix before and after saponification.

Bacteria and Acidic Drainage from Coal Refuse: Inhibition by Sodium Lauryl Sulfate and Sodium Benzoate

Science.gov (United States)

Dugan, Patrick R.; Apel, William A.

1983-01-01

The application of an aqueous solution of sodium lauryl sulfate and sodium benzoate to the surface of high-sulfur coal refuse resulted in the inhibition of iron-and sulfur-oxidizing chemoautotrophic bacteria and in the decrease of acidic drainage from the refuse, suggesting that acid drainage can be abated in the field by inhibiting iron- and sulfur-oxidizing bacteria. PMID:16346347

Power generation from chemically cleaned coals: do environmental benefits of firing cleaner coal outweigh environmental burden of cleaning?

DEFF Research Database (Denmark)

Ryberg, Morten W.; Owsianiak, Mikolaj; Laurent, Alexis

2015-01-01

Power generation from high-ash coals is a niche technology for power generation, but coal cleaning is deemed necessary to avoid problems associated with low combustion efficiencies and to minimize environmental burdens associated with emissions of pollutants originating from ash. Here, chemical...... beneficiation of coals using acid and alkali–acid leaching procedures is evaluated as a potential coal cleaning technology employing life cycle assessment (LCA). Taking into account the environmental benefits from firing cleaner coal in pulverized coal power plants and the environmental burden of the cleaning...... itself, it is demonstrated that for a wide range of cleaning procedures and types of coal, chemical cleaning generally performs worse than combustion of the raw coals and physical cleaning using dense medium separation. These findings apply for many relevant impact categories, including climate change...

Plan for injection of coal combustion byproducts into the Omega Mine for the reduction of acid mine drainage

International Nuclear Information System (INIS)

Gray, T.A.; Moran, T.C.; Broschart, D.W.; Smith, G.A.

1998-01-01

The Omega Mine Complex is located outside of Morgantown, West Virginia. The mine is in the Upper Freeport Coal, an acid-producing coal seam. The coal was mined in a manner that has resulted in acid mine drainage (AMD) discharges at multiple points. During the 1990's, the West Virginia Division of Environmental Protection (WVDEP) assumed responsibility for operating a collection and treatment system for the AMD. Collection and treatment costs are approximately $300,000 per year. Injecting grout into the mine workings to reduce AMD (and thus reducing treatment costs) is proposed. The procedure involves injecting grout mixes composed primarily of coal combustion byproducts (CCB's) and water, with a small quantity of cement. The intention of the injection program is to fill the mine voids in the north lobe of the Omega Mine (an area where most of the acidity is believed to be generated) with the grout, thus reducing the contact of air and water with potentially acidic material. The grout mix design consists of an approximate 1:1 ratio of fly ash to byproducts from fluidized bed combustion. Approximately 100 gallons of water per cubic yard of grout is used to achieve flowability. Observation of the mine workings via subsurface borings and downhole video camera confirmed that first-mined areas were generally open while second-mined areas were generally partially collapsed. The injection program was developed to account for this by utilizing closer injection hole spacing in second-mined areas. Construction began in January 1998, with grout injection expected to commence in mid-April 1998

New method for reduction of burning sulfur of coal

International Nuclear Information System (INIS)

Lyutskanov, L.; Dushanov, D.

1998-01-01

The coal pyrolysis is key phase in the the pyrolysis-combustion cycle as it provides char for combustor. The behaviour of sulfur compounds during coal pyrolysis depends on factors as rank of coal, quantity of sulfur and sulfur forms distribution in the coal, quantity and kind of mineral matter and the process conditions. The mineral content of coal may inhibit or catalyze the formation of volatile sulfur compounds. The pyrolysis itself is a mean of removing inorganic and organic sulfur but anyway a portion of it remains in the char while the other moves into the tar and gas. The aim of this study was to determine an optimal reduction of burning sulfur at the coal pyrolysis by varying parametric conditions. The pyrolysis of different kinds of coal has been studied. The samples with size particles o C at atmospheric pressure and with a heating rate of 6-50 o C min -1 . They were treated with exhaust gas and nitrogen at an addition of steam and air. The char obtained remains up to 10 min at the final temperature. The char samples cool without a contact with air. Two methods of desulfurization-pyrolysis were studied - using 9-vertical tubular reactor and 9-horizontal turning reactor. The results obtained show that at all samples there is a decrease of burning sulfur with maximal removal efficiency 83%. For example at a pyrolysis of Maritsa Iztok lignite coal the burning sulfur is only 16% in comparison with the control sample. The remained is 90% sulfate, 10% organic and pyrite traces when a mixture 'exhaust gas-water stream-air' was used. The method of desulfurization by pyrolysis could be applied at different kinds of coal and different conditions. Char obtained as a clean product can be used for generating electric power. This innovation is in a stage of patenting

Chemical and physical characteristics of tar samples from selected Manufactured Gas Plant (MGP) sites

International Nuclear Information System (INIS)

Ripp, J.; Taylor, B.; Mauro, D.; Young, M.

1993-05-01

A multiyear, multidisciplinary project concerning the toxicity of former Manufactured Gas Plant (MGP) tarry residues was initiated by EPRI under the Environmental Behavior of Organic Substances (EBOS) Program. This report concerns one portion of that work -- the collection and chemical characterization of tar samples from several former MGP sites. META Environmental, Inc. and Atlantic Environmental Services, Inc. were contracted by EPRI to collect several samples of tarry residues from former MGP sites with varied historical gas production processes and from several parts of the country. The eight tars collected during this program were physically very different. Some tars were fluid and easily pumped from existing wells, while other tars were thicker, semi-solid, or solid. Although care was taken to collect only tar, the nature of the residues at several sites made it impossible not to collect other material, such as soil, gravel, and plant matter. After the samples were collected, they were analyzed for 37 organic compounds, 8 metals, and cyanide. In addition, elemental analysis was performed on the tar samples for carbon, hydrogen, oxygen, sulfur and nitrogen content and several physical/chemical properties were determined for each tar. The tars were mixed together in different batches and distributed to researchers for use in animal toxicity studies. The results of this work show that, although the tars were produced from different processes and stored in different manners, they had some chemical similarities. All of the tars, with the exception of one unusual solid tar, contained similar relative abundances of polycyclic aromatic hydrocarbons (PAHs)

Thermodynamic analysis of tar reforming through auto-thermal reforming process

Energy Technology Data Exchange (ETDEWEB)

Nurhadi, N., E-mail: nurhadi@tekmira.esdm.go.id; Diniyati, Dahlia; Efendi, M. Ade Andriansyah [R& D Centre for Mineral and Coal Technology, Jln. Jend.Sudirman no. 623, Bandung. Telp. 022-6030483 (Malaysia); Istadi, I. [Department of Chemical Engineering, Diponegoro University, Jln. Jl. Prof. Soedarto, SH, Semarang (Malaysia)

2015-12-29

Fixed bed gasification is a simple and suitable technology for small scale power generation. One of the disadvantages of this technology is producing tar. So far, tar is not utilized yet and being waste that should be treated into a more useful product. This paper presents a thermodynamic analysis of tar conversion into gas producer through non-catalytic auto-thermal reforming technology. Tar was converted into components, C, H, O, N and S, and then reacted with oxidant such as mixture of air or pure oxygen. Thus, this reaction occurred auto-thermally and reached chemical equilibrium. The sensitivity analysis resulted that the most promising process performance occurred at flow rate of air was reached 43% of stoichiometry while temperature of process is 1100°C, the addition of pure oxygen is 40% and preheating of oxidant flow is 250°C. The yield of the most promising process performance between 11.15-11.17 kmol/h and cold gas efficiency was between 73.8-73.9%.The results of this study indicated that thermodynamically the conversion of tar into producer gas through non-catalytic auto-thermal reformingis more promising.

Pelagic tar and plastic in the Gulf of Alaska and Bering Sea: 1975

Energy Technology Data Exchange (ETDEWEB)

Shaw, D G

1977-07-01

Seventy-one tows of 740 m/sup 2/ each were made in search of pelagic tar and plastics in the Gulf of Alaska and Bering Sea during the period October 1974 to October 1975. Tar was observed on nine occasions while plastics were found six times. The arithmetic mean value of tar abundance, 3.3 x 10/sup -3/ mg/m/sup 2/, is considerably lower than most other oceanic areas for which values have been reported. Gas chromatographic analysis of this tar indicates that it is more extensively weathered than tar from the north Atlantic. An estimate of the abundance of tar lumps too small to be sampled by net tows is made based on the assumption that there are equal weights of particles in logarithmetically equal size intervals. The abundance of pelagic plastics is also low.

Evaluation of pitches and cokes from solvent-extracted coal materials

Energy Technology Data Exchange (ETDEWEB)

McHenry, E.R.

1996-12-01

Three initial coal-extracted (C-E) samples were received from the West Virginia University (WVU) Chemical Engineering Department. Two samples had been hydrogenated to obtain pitches that satisfy Theological requirements. One of the hydrogenated (HC-E) samples had been extracted by toluene to remove ash and higher molecular weight aromatic compounds. We were unable to measure the softening point and viscosity of the non-hydro treated solid extract sample, Positive characteristics in the HC-E materials were softening points of 113-119{degrees}C, low sulfur and ash. The oxygen and nitrogen content of the HC-E samples may limit future usage in premium carbon and graphite products. Coking values were similar to petroleum pitches. Laboratory anode testing indicates that in combination with standard coal-tar pitch, the HC-E material can be used as a binder pitch.

Coal pyrolysis in a continuous fluidized bed - process development studies

Energy Technology Data Exchange (ETDEWEB)

Ramakrishnan, N N; Akmal, M A.K.; Vaidyeswaran, R

1981-10-01

The paper deals with the development of a process development unit (PDU) for the fluid bed pyrolysis of non-caking slack coal obtained from Singareni and Talcher coalfields. Preheated air is used as the fluidizing medium. It is necessary to avoid its maldistribution by a suitable design of the gas distributor. In this regard perforated conical distributors appear to play an important role. In the low temperature carbonization of coal an operation around 500 C gives optimum yields of char and tar of desirable quality. Carbonization reactions are generally completed within about 20 min of the feed entry into the fluidized bed and the char attains an equilibrium volatile matter content. Since air is used as the fluidizing medium carbonization gas is diluted with nitrogen and non-combustibles. The heating value of the gas is low. (5 refs.)

W(h)ither the coal industry? The long-term view

International Nuclear Information System (INIS)

Schobert, H.H.; Rusinko, F. Jr.; Mathews, J.P.

1998-01-01

Global warming--real or imaginary, friend or foe, carbon dioxide emissions a threat to the planet, benign, or good for agriculture--while the debate rages on, the debaters occasionally seem to pause long enough to agree on one point: coal is the bad guy. There is little doubt that coal combustion must continue as a major contributor to the energy economy for the near to mid-term future. It is likely, though, those environmental pressures on conventional processes for coal utilization will only intensify. This factor alone makes questionable the long-term future. Environmental issues also severely impact the metallurgical coke industry. The traditional coal industry and coal markets of the 20th century are under increasingly intense assault. But why waste coal by burning it? Steady progress is being made in two directions for using coal as a valuable hydrocarbon resource. On the one hand, continuous improvements in computer-based structural modeling, which now include the ability to calculate not only a molecular structure that is consistent with chemical facts, but also some of the physical properties and even the incorporation of water. The increasing reasonableness of such structures places one on the verge of being able to do rational organic chemistry on coals, that is, deliberately to select coals as starting materials for certain desired chemical transformations that will produce high-value chemical products in good yields. This opens a route to chemicals from coal that does not rely on by-product coal tars as the feedstock. On the other hand, excellent opportunities also exist for coals as precursors to high-value carbon materials. Anthracites in particular represent an under-exploited, and as yet poorly explored, opportunity for conversion to graphitic materials. Taking coal in both directions high-value chemicals and premium carbon products represent profitable opportunities for innovation, leadership, and new directions for the coal industry in the 21st

Iron-based materials as tar cracking catalyst in waste gasification

Energy Technology Data Exchange (ETDEWEB)

Nordgreen, Thomas

2011-07-01

The treatment of municipal solid waste (MSW) in Sweden has changed during the past decades due to national legislation and European Union directives. The former landfills have more or less been abandoned in favour of material recycling and waste incineration. On a yearly basis approximately 2.2 million tonnes waste are incinerated in Sweden with heat recovery and to some extent also with electricity generation, though at a low efficiency. It is desirable to alter this utilisation and instead employ MSW as fuel in a fluid bed gasification process. Then electrical energy may be produced at a much higher efficiency. However, MSW contain about 1 % chlorine in the form of ordinary table salt (NaCl) from food scraps. This implies that the tar cracking catalyst, dolomite, which is normally employed in gasification, will suffer from poisoning if applied under such conditions. Then the tar cracking capacity will be reduced or vanish completely with time. Consequently, an alternative catalyst, more resistant to chlorine, is needed. Preliminary research at KTH has indicated that iron in its metallic state may possess tar cracking ability. With this information at hand and participating in the project 'Energy from Waste' an experimental campaign was launched. Numerous experiments were conducted using iron as tar cracking catalyst. First iron sinter pellets from LKAB were employed. They were reduced in situ with a stream of hydrogen before they were applied. Later iron-based granules from Hoeganaes AB were tested. These materials were delivered in the metallic state. In all tests the KTH atmospheric fluidised bed gasifier with a secondary catalytic reactor housing the catalytic material was deployed. Mostly, the applied fuel was birch. The results show that metallic iron possesses an intrinsic ability, almost in the range of dolomite, to crack tars. Calculations indicate that iron may be more resistant to chlorine than dolomite. The exploration of metallic iron

Fate of the naturally occurring radioactive materials during treatment of acid mine drainage with coal fly ash and aluminium hydroxide.

Science.gov (United States)

Madzivire, Godfrey; Maleka, Peane P; Vadapalli, Viswanath R K; Gitari, Wilson M; Lindsay, Robert; Petrik, Leslie F

2014-01-15

Mining of coal is very extensive and coal is mainly used to produce electricity. Coal power stations generate huge amounts of coal fly ash of which a small amount is used in the construction industry. Mining exposes pyrite containing rocks to H2O and O2. This results in the oxidation of FeS2 to form H2SO4. The acidic water, often termed acid mine drainage (AMD), causes dissolution of potentially toxic elements such as, Fe, Al, Mn and naturally occurring radioactive materials such as U and Th from the associated bedrock. This results in an outflow of AMD with high concentrations of sulphate ions, Fe, Al, Mn and naturally occurring radioactive materials. Treatment of AMD with coal fly ash has shown that good quality water can be produced which is suitable for irrigation purposes. Most of the potentially toxic elements (Fe, Al, Mn, etc) and substantial amounts of sulphate ions are removed during treatment with coal fly ash. This research endeavours to establish the fate of the radioactive materials in mine water with coal fly ash containing radioactive materials. It was established that coal fly ash treatment method was capable of removing radioactive materials from mine water to within the target water quality range for drinking water standards. The alpha and beta radioactivity of the mine water was reduced by 88% and 75% respectively. The reduced radioactivity in the mine water was due to greater than 90% removal of U and Th radioactive materials from the mine water after treatment with coal fly ash as ThO2 and UO2. No radioisotopes were found to leach from the coal fly ash into the mine water. Copyright © 2013 Elsevier Ltd. All rights reserved.

Secondary reactions of tar during thermochemical biomass conversion[Dissertation 14341

Energy Technology Data Exchange (ETDEWEB)

Morf, P.O.

2001-07-01

This dissertation submitted to the Swiss Federal Institute of Technology in Zurich presents and discusses the results obtained during the examination of the processes involved in the formation and conversion of tar in biomass gasification plant. Details are given on the laboratory reactor system used to provide separated tar production and conversion for the purposes of the experiments carried out. The results of analyses made of the tar and the gaseous products obtained after its conversion at various temperatures are presented. The development of kinetic models using the results of the experiments that were carried out is described. The results of the experiments and modelling are compared with the corresponding results obtained using a full-scale down-draft, fixed-bed gasifier. The author is of the opinion that the reaction conditions found in full-scale gasifiers can be well simulated using heterogeneous tar conversion experiments using the lab reactor system.

Tar loads on Omani beaches

International Nuclear Information System (INIS)

Badawy, M.I.; Al-Harthy, F.T.

1991-01-01

Owing to Oman's geographic position and long coastal line, the coastal areas of Oman are particularly vulnerable to oil pollution from normal tanker operations, illegal discharges, and accidental spills as well as local sources of oil input. UNEP carried out a survey on the coasts of Oman to determine the major sources of oil pollution and concluded that the major shoreline pollution problems in Oman arose from operational discharges of oil from passing vessels traffic. The oil, because of the high sea and air temperatures in the area, was subjected to relatively high rates of evaporation and photo-oxidation and tended to arrive at the coast as heavy petroleum particulate residues (tar balls). The aim of the present study was to measure the loads of tar balls in Omani coastal areas and to identify the source of oil pollutants on beaches

Decomposition of tar in gas from updraft gasifier by thermal cracking

DEFF Research Database (Denmark)

Brandt, Peder; Henriksen, Ulrik Birk

2000-01-01

Continuing earlier work with tar reduction by partial oxidation of pyrolysis gas [1] thermal cracking has been evaluated as a gas cleaning process. The work has been focusing on cleaning gas from updraft gasifiers, and the long term purpose is to develop a tar cleaning unit based on thermal...... cracking. An experimental set-up has been built, in which a flow of contaminated gas can be heated up to 1290°C in a reactor made of pure Al2O3. Four measurements were made. Three with gas from a pyrolysis unit simulating updraft gasifier, and one with gas from an updraft gasifier. Cracking temperatures...... was 1200, 1250 and 1290°C, and the residence time at this temperature was 0.5 second. The measurements show that at the selected residence time of 0.5 second, the gas flow in a thermal tar cracking unit has to be heated to at least 1250°C to achieve sufficient tar cleaning. At 1290°C, a tar content as low...

Sumpor u ugljenu (Sulphur in Coal

Directory of Open Access Journals (Sweden)

Rađenović, A.

2004-12-01

Full Text Available The presence of sulphur in coal possesses important environmetal problems in its usage. The sulphur dioxide (S02 emissions produced during coal combustion account for a significant proportion of the total global output of anthropogenic SO2. The extent of sulphur separation depends on several variables such as the form of sulphur in coal, intimacy of contact between minerals and the products of devolatilization. The total sulphur in coal varies in the range of 0.2 - 11 wt %, although in most cases it is beetwen 1 and 3 wt %. Sulphur occurs in a variety of both inorganic and organic forms. Inorganic sulphur is found mainly as iron pyrite, marcasite, pyrrhotite, sphalerite, galena, chalcopirite and as sulphates (rarely exceeds w = 0,1 %. Organic sulphur is found in aromatic rings and aliphatic functionalities usually as mercaptans, aliphatic and aryl sulfides, disulfides and thiophenes. Organic and pyritic sulphur quantities depend on coal rank. Higher rank coals tend to have a high proportion of labile sulphur. All the organic sulphur is bivalent and it is spread throughout the organic coal matrix. Sulphur occurs in all the macerals and most minerals. Vitrinite contains the major part of organic sulphur and metals. Elemental sulphur is produced during coal weathering. The depolymerization methods as pyrolysis and hydrogenation are very drastic methods wich change the structure of the coal and the sulphur groups. In the case of pyrolysis, high levels of desulphurization, in chars and additional production of liquid hydrocarbon can be achieved. Thiophenes and sulphides were the major sulphur components of tars from coal pyrolysis. Hyrdogen sulphide and the lower mercaptans and sulphides were found in the volatile matters. Hydrogen sulphide and thiophenes are practically the only sulphur products of coal hydrogenation. H2S is produced in char hydrodesulphurization. A number of options are available for reducing sulphur emissions including the

Advances in coal chemistry, 1950--1970. [21 refs

Energy Technology Data Exchange (ETDEWEB)

Brooks, J D

1971-12-01

During the 20 years under review, considerable advances were made at centers of coal research throughout the world in the determination of the chemical structure and reactions of coals. Important contributions came from the CSIRO group in Sydney. Activity was greatest during the first decade of the period under review and declined progressively during the second, as evidence of the extreme complexity of coal structures made it clear that further chemical research would be less rewarding. Some overseas investigations were related mainly to chemical processes for the conversion of coals to liquid and gaseous fuels, and to possible direct chemical utilization; but in Australia, because of the relatively small size of the potential market and the widely dispersed centers of population, such studies were not relevant to the current situation. Much of the Australian research in this field was related to carbonization processes and to the chemical and physical processes involved in the thermal treatment of coals. The high-light was perhaps the investigation, begun in 1960, which showed how coals, pitch, and bitumen resolidify during heating to form coke. Determinations were also made of the chemical composition of tars and pitches produced both industrially and in the laboratory and efforts were made to develop local outlets for these by-products of gas-making and of steelworks coke ovens. The pattern of Australian fuel consumption changed considerably during the 20-year period, and in particuar there was considerable development in the use of petroleum by-products for gas-making. Research on the manufacture of metallurgical coke was established within the steel industry, and in response to these factors basic work by CSIRO in bituminous coal chemistry had virtually ceased by the end of 1966.

[Effect of soil phenolic acids on soil microbe of coal-mining depressed land after afforestation restoration by different tree species].

Science.gov (United States)

Ji, Li; Yang, Li Xue

2017-12-01

Phenolic acids are one of the most important factors that influence microbial community structure. Investigating the dynamic changes of phenolic acids and their relationship with the microbial community structure in plantation soils with different tree species could contribute to better understanding and revealing the mechanisms of microbial community changes under afforestation restoration in coal-mining subsidence areas. In this study, plantations of three conifer and one deciduous species (Pinus koraiensis, Larix gmelinii, Pinus sylvestris var. mongolica, and Populus ussuriensis) were established on abandoned coal-mining subsidence areas in Baoshan District, Shuangyashan City. The contents of soil phenols, 11 types of phenolic acids, and microbial communities in all plots were determined. The results showed that the contents of soil complex phenol in plantations were significantly higher than that of abandoned land overall. Specifically, soils in larch and poplar plantations had higher contents of complex phenol, while soils in larch and Korean pine plantations had greater contents of total phenol. Moreover, soil in the P. koraiensis plantation had a higher content of water-soluble phenol compared with abandoned lands. The determination of 11 phenolic acids indicated that the contents of ferulic acid, abietic acid, β-sitosterol, oleanolic acid, shikimic acid, linoleic acid, and stearic acid were higher in plantation soils. Although soil phenol contents were not related with soil microbial biomass, the individual phenolic acids showed a significant relationship with soil microbes. Ferulic acid, abietic acid, and β-sitosterol showed significant promoting effects on soil microbial biomass, and they showed positive correlations with fungi and fungi/bacteria ratio. These three phenolic acids had higher contents in the poplar plantation, suggesting that poplar affo-restation had a beneficial effect on soil quality in coal-mining subsidence areas.

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular proteins

Biotransformation of Spanish coals by microorganisms; Biotransformacion de Carbones Espanoles por Microorganismos

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

some newly isolated microorganisms could solubilized different kinds of Spanish coals (hard coal, subbituminous coal and lignite). Certain fungi and bacteria could solubilized lignite when growing in a mineral medium. However, to solubilized higher rank coals (hard coal and subbituminous coal) microorganisms require a complete medium. Microorganisms, which showed higher capacity to solubilized coal, were incubated in the presence of coal (hard coal, subbituminous coal and lignite) at the optimal conditions to get coal liquefaction/solubilization. The resultant products were analysed by IR and UV/visible spectrometry. No major differences among the original coal, solubilized/liquefied coal and residual coal were detected. However, an increase in metallic carboxylate and a decrease in OH'- carboxylic groups were observed in the liquefied lignite. Humic acids derived from original lignite residual lignite and liquefied/solubilized lignite by microorganisms were analysed. Several differences were observed in the humic acids extracted from the liquefied lignite, such as an increase in the total acidity and in the proportion of the phenolic groups. Differences on the humic acid molecular weight were observed too. Several fungal and bacterial strains were able to grow using humic acids as sole carbon source. Microorganisms growing in humic acid were observed by Scanning Electron Microscopy. Besides, the coal solubilization capacity of several fungal strains (M2, m$ and AGI) growing in different culture media was assayed. In order to get some insight into the mechanisms of the liquefaction/solubilization of Spanish coals (hard coal, subbituminous coal and lignite) by these microorganisms, some features in the culture supernatants were studied: pH values; extracellular specific proteins; enzyme activities possibly related with coal solubilization and the presence of oxalate. M2 and M4 fungal strains grown in the presence of coal produced some specific extracellular

A review of acidity generation and consumption in acidic coal mine lakes and their watersheds.

Science.gov (United States)

Blodau, Christian

2006-10-01

Lakes developing in former coal mine pits are often characterized by high concentrations of sulfate and iron and low pH. The review focuses on the causes for and fate of acidity in these lakes and their watersheds. Acidification is primarily caused by the generation of ferrous iron bearing and mineralized groundwater, transport through the groundwater-surface water interface, and subsequent iron oxidation and precipitation. Rates of acidity generation in mine tailings and dumps, and surface water are often similar (1 to >10 mol m(-2) yr(-1)). Weathering processes, however, often suffice to buffer groundwaters to only moderately acidic or neutral pH, depending on the suite of minerals present. In mine lakes, the acidity balance is further influenced by proton release from transformation of metastable iron hydroxysulfate minerals to goethite, and proton and ferrous iron sequestration by burial of iron sulfides and carbonates in sediments. These processes mostly cannot compensate acidity loading from the watershed, though. A master variable for almost all processes is the pH: rates of pyrite oxidation, ferrous iron oxidation, mineral dissolution, iron precipitation, iron hydroxide transformation, and iron and sulfate reduction are strongly pH dependent. While the principle mechanism of acidity generation and consumption and several controls are mostly understood, this cannot be said about the fate of acidity on larger spatial and temporal scales. Little is also known about critical loads and the internal regulation of biogeochemical iron, sulfur, and carbon cycling in acidic mine lakes.

A review of acidity generation and consumption in acidic coal mine lakes and their watersheds

International Nuclear Information System (INIS)

Blodau, Christian

2006-01-01

Lakes developing in former coal mine pits are often characterized by high concentrations of sulfate and iron and low pH. The review focuses on the causes for and fate of acidity in these lakes and their watersheds. Acidification is primarily caused by the generation of ferrous iron bearing and mineralized groundwater, transport through the groundwater-surface water interface, and subsequent iron oxidation and precipitation. Rates of acidity generation in mine tailings and dumps, and surface water are often similar (1 to >10 mol m -2 yr -1 ). Weathering processes, however, often suffice to buffer groundwaters to only moderately acidic or neutral pH, depending on the suite of minerals present. In mine lakes, the acidity balance is further influenced by proton release from transformation of metastable iron hydroxysulfate minerals to goethite, and proton and ferrous iron sequestration by burial of iron sulfides and carbonates in sediments. These processes mostly cannot compensate acidity loading from the watershed, though. A master variable for almost all processes is the pH: rates of pyrite oxidation, ferrous iron oxidation, mineral dissolution, iron precipitation, iron hydroxide transformation, and iron and sulfate reduction are strongly pH dependent. While the principle mechanism of acidity generation and consumption and several controls are mostly understood, this cannot be said about the fate of acidity on larger spatial and temporal scales. Little is also known about critical loads and the internal regulation of biogeochemical iron, sulfur, and carbon cycling in acidic mine lakes. (author)

Development of Mercury and Hydrogen Chloride Emission Monitors for Coal Gasifiers

Energy Technology Data Exchange (ETDEWEB)

G. Norton; D. Eckels; C. Chriswell

2001-02-26

The gas conditioning issues involved with coal gasification streams are very complex and do not have simple solutions. This is particularly true in view of the fact that the gas conditioning system must deal with tars, high moisture contents, and problems with NH{sub 3} without affecting low ppb levels of Hg, low levels (low ppm or less) of HCl, or the successful operation of conditioner components and analytical systems. Those issues are far from trivial. Trying to develop a non-chemical system for gas conditioning was very ambitious in view of the difficult sampling environment and unique problems associated with coal gasification streams. Although a great deal was learned regarding calibration, sample transport, instrumentation options, gas stream conditioning, and CEM design options, some challenging issues still remain. Sample transport is one area that is often not adequately considered. Because of the gas stream composition and elevated temperatures involved, special attention will need to be given to the choice of materials for the sample line and other plumbing components. When using gas stream oxidation, there will be sample transport regions under oxidizing as well as reducing conditions, and each of those regions will require different materials of construction for sample transport. The catalytic oxidation approach worked well for removal of tars and NH{sub 3} on a short term basis, but durability issues related to using the catalyst tube during extended testing periods still require study.

Monitoring of tar contents in gases. Final report

Energy Technology Data Exchange (ETDEWEB)

Petersen, Finn [ChimneyLab Europe ApS, Hadsten (Denmark); Houmann Jakobsen, H. [BioSynergi Proces ApS, Hoersholm (Denmark)

2012-08-15

The purpose of this project is to develop and test a relative cheap and simple online tar measuring method, which can monitor the tar content in product gas from thermal gasification. The measuring principle is absorption of tar from sample gas in Isopropanol (IPA), and measuring on this solution by UV-spectrophotometer. Continuous sampling of tar containing producer gas turned out to be a larger problem than earlier foreseen. The best solution was decided to be sampling with higher flows, and afterwards cleaning the IPA in activated carbon. The ambitions for continuous sampling had to be decreased to 1 week, where the IPA and the activated carbon is contaminated by tar and has to be replaced. However this requires larger amounts of IPA and activated carbon. For IPA the weekly consumption was 12-15 Litres and for activated carbon 10 Litres. The whole analyzer unit turned out to be more complex than first projected, mainly because of the increased amounts of IPA. The best mist filter, with respect to pressure drop, efficiency and retention time is a combination of glass wool and quarts wool. The unit has been tested on gas; 20 kW pellets burner for 116 hours. Harbooere updraft gasifier for 519 hours. Skive fluid bed gasifier for 879 hours. There have during the project period been several simple practical problems such as bubbles in the IPA, increasing pressure drop over the activated carbon bed, dropout of UV data acquisition program and increasing baseline. The principle showed from the beginning some good results, with the limitation of 1 week continuous operation, but at the 5. period in Skive the baseline was increasing all the time, and it was not possible to solve this problem. (LN)

Modelling the low-tar BIG gasification concept[Biomass Integrated gasification

Energy Technology Data Exchange (ETDEWEB)

Andersen, Lars; Elmegaard, B.; Qvale, B.; Henriksen, Ulrrik [Technical univ. of Denmark (Denmark); Bentzen, J.D.; Hummelshoej, R. [COWI A/S (Denmark)

2007-07-01

A low-tar, high-efficient biomass gasification concept for medium- to large-scale power plants has been designed. The concept is named 'Low-Tar BIG' (BIG = Biomass Integrated Gasification). The concept is based on separate pyrolysis and gasification units. The volatile gases from the pyrolysis (containing tar) are partially oxidised in a separate chamber, and hereby the tar content is dramatically reduced. Thus, the investment, and running cost of a gas cleaning system can be reduced, and the reliability can be increased. Both pyrolysis and gasification chamber are bubbling fluid beds, fluidised with steam. For moist fuels, the gasifier can be integrated with a steam drying process, where the produced steam is used in the pyrolysis/gasification chamber. In this paper, mathematical models and results from initial tests of a laboratory Low-Tar BIG gasifier are presented. Two types of models are presented: 1. The gasifier-dryer applied in different power plant systems: Gas engine, Simple cycle gas turbine, Recuperated gas turbine and Integrated Gasification and Combined Cycle (IGCC). The paper determines the differences in efficiency of these systems and shows that the gasifier will be applicable for very different fuels with different moisture contents, depending on the system. 2. A thermodynamic Low-Tar BIG model. This model is based on mass and heat balance between four reactors: Pyrolysis, partial oxidation, gasification, gas-solid mixer. The paper describes the results from this study and compares the results to actual laboratory tests. The study shows, that the Low-Tar BIG process can use very wet fuels (up to 65-70% moist) and still produce heat and power with a remarkable high electric efficiency. Hereby the process offers the unique combination of large scale gasification and low-cost gas cleaning and use of low-cost fuels which very likely is the necessary combination that will lead to a breakthrough of gasification technology. (au)

Structural and dynamic characterization of the upper part of the HIV-1 cTAR DNA hairpin

OpenAIRE

Zargarian, Loussin?; Kanevsky, Igor; Bazzi, Ali; Boynard, Jonathan; Chaminade, Fran?oise; Foss?, Philippe; Mauffret, Olivier

2009-01-01

First strand transfer is essential for HIV-1 reverse transcription. During this step, the TAR RNA hairpin anneals to the cTAR DNA hairpin; this annealing reaction is promoted by the nucleocapsid protein and involves an initial loop?loop interaction between the apical loops of TAR and cTAR. Using NMR and probing methods, we investigated the structural and dynamic properties of the top half of the cTAR DNA (mini-cTAR). We show that the upper stem located between the apical and the internal loop...

Creating fluid injectivity in tar sands formations

Science.gov (United States)

Stegemeier, George Leo; Beer, Gary Lee; Zhang, Etuan

2010-06-08

Methods for treating a tar sands formation are described herein. Methods for treating a tar sands may include heating a portion of a hydrocarbon layer in the formation from one or more heaters located in the portion. The heat may be controlled to increase the permeability of at least part of the portion to create an injection zone in the portion with an average permeability sufficient to allow injection of a fluid through the injection zone. A drive fluid and/or an oxidizing fluid may be provided into the injection zone. At least some hydrocarbons are produced from the portion.

Chemical and Spectroscopical Characterization of Humic Acids from two South Brazilian Coals of Different Ranks

Directory of Open Access Journals (Sweden)

Dick Deborah P.

2002-01-01

Full Text Available Humic acids (HA extracted from two coals of different ranks, from their regenerated samples and from a nitrated sample, were characterized by elemental analysis and by infra-red (FTIR, solid state 13C nuclear magnetic resonance (NMR and eletronic paramagnetic resonance (EPR spectroscopies. The low rank coal HA presented higher C and lower O contents, higher C/N and lower H/C and O/C ratios than high rank coal HA. NMR results showed that both samples were more aromatic and less carboxylic than common soil HA. Those characteristics may limit the coal HA efficiency as an appropriate soil conditioner and fertilizer. The regeneration process did not produce major alterations in the coal HA, except a decrease of the free radical content as determined by EPR spectroscopy. Probably, the regeneration conditions and time were not adequate to oxidize the samples. The obtained FTIR spectra were much alike, except that from the nitrated sample, where the absorption band at 1533 cm-1 confirms the presence of nitrated groups. The nitration process increased the N content and reduced the C/N ratio to values comparable to those reported for soil HA, but the aromaticity still remained high and the carboxylic content was lowered after the procedure.

Phyto-bioconversion of hard coal in the Cynodon dactylon/coal rhizosphere.

Science.gov (United States)

Igbinigie, Eric E; Mutambanengwe, Cecil C Z; Rose, Peter D

2010-03-01

Fundamental processes involved in the microbial degradation of coal and its derivatives have been well documented. A mutualistic interaction between plant roots and certain microorganisms to aid growth of plants such as Cynodon dactylon (Bermuda grass) on hard coal dumps has recently been suggested. In the present study coal bioconversion activity of nonmycorrhizal fungi was investigated in the C. dactylon/coal rhizosphere. Fungal growth on 2% Duff-agar, gutation formation on nitric acid treated coal and submerged culture activity in nitrogen-rich and -deficient broth formed part of the screening and selection of the fungi. The selected fungal isolates were confirmed to be found in pristine C. dactylon/coal rhizosphere. To simulate bioconversion, a fungal aliquot of this rhizosphere was used as inoculum for a Perfusate fixed bed bioreactor, packed with coal. The results demonstrate an enhanced coal bioconversion facilitated by low molecular weight organics and the bioconversion of coal may be initiated by an introduction of nitrogen moieties to the coal substrate. These findings suggest a phyto-bioconversion of hard coal involving plant and microbes occurring in the rhizosphere to promote the growth of C. dactylon. An understanding of this relationship can serve as a benchmark for coal dumps rehabilitation as well as for the industrial scale bioprocessing of hard coal.

Coal pyrolysis. VII. Economic viability of pyrolysis. Pirolisis del carbon. VII. Viabilidad economica de la pirolisis

Energy Technology Data Exchange (ETDEWEB)

Molinar, R.; Adanez, J.; Miranda, J.L.; Ibarra, J.V. (Instituto de Carboquimica, Zaragoza (Spain))

1989-04-01

Analyses the most important economic parameters of the main pyrolysis processes. Considers the markets available for semi-coke and tars. Concludes that no single technology or process has clear advantages over the others because all depends on the type of coal being used and the purpose for which the end product is to be used. Refers to studies carried out in Canada and the USA on the same subject and reports their findings. Concludes optimistically that coal pyrolysis shows promise of being economically viable in the future because although initially, costs reflect the high financial outlay necessary to begin operations, after a certain period, these costs fall and the end product can be sold at a lower price. A further point in favour of pyrolysis is that coal prices are likely to rise more slowly than oil prices. 5 refs., 8 tabs.

Epoxy-coal hydraulic insulation for structures of the Nurek Hydroelectric Powerplant

Energy Technology Data Exchange (ETDEWEB)

Sakharov, V I; Segal, M S; Solov' ev, I N; Yazev, R E

1978-03-01

The design of the Nurek Powerplant exposed the base of the core of the dam to a head of 270 m. To avoid seepage, it was decided to construct an antiseepage screen. Given the total hydraulic insulation area required, 26,540 m/sup 2/, the use of a metal screen would be quite expensive. It was therefore decided to use an epoxy-coal material consisting of a primer, varnish and enamel based on epoxy resins modified by the addition of coal tar, a waste product from the dry distillation of coal. A typical hydraulic insulation layer consists of a coat of primer, three or four coats of varnish and a coat of enamel. Glass-reinforced fabric is used with the first through third coats of varnish to increase crack resistance. The coating thus produced is found to be resistant to overbearing soil pressure of up to 600 t/m/sup 2/, hydrostatic head of up to 300 m and constant shear forces of up to 100 t/m/sup 2/. The method also saves labor and expensive metal.

The separate effects of tar and nicotine on the cigarette smoking manoeuvre

International Nuclear Information System (INIS)

Woodman, G.; Newman, S.P.; Paiva, D.; Clarke, S.W.

1987-01-01

The separate effects of tar and nicotine on the cigarette smoking manoeuvre were investigated. Each of ten asymptomatic habitual smokers smoked three different commercially available cigarettes in a randomised order. The brands were chosen such that two had the same tar yield (10 mg) and two had the same nicotine yield (1.4 mg). The volume of smoke inhaled into the lungs was measured by tracing the smoke with the inert gas 81 Kr m . Puffing indices were recorded using an electronic smoking analyser and flowhead/cigarette holder. There was no difference in the total volume of smoke puffed from each of the cigarette brands. With cigarettes of the samme tar level, the total inhaled smoke volume was lower with the higher nicotine cigarette (P<0.05): by contrast, with cigarettes of the same nicotine level, the toal inhaled smoke volume was lower with the lower tar cigarette (P<0.02). Tar and nicotine appear to exercise independent control over the volume of smoke inhaled. (author)

Prevention of formation of acid drainage from high-sulfur coal refuse by inhibition of iron- and sulfur-oxidizing microorganisms. 1. Preliminary experiments in controlled shaken flasks

Energy Technology Data Exchange (ETDEWEB)

Dugan, P.R.

1987-01-01

Changes of pH and sulfate concentration in high-sulfur coal refuse slurries are used as measurements of microbial pyrite oxidation in the laboratory. Sodium lauryl sulfate (SLS), alkylbenzene sulfonate (ABS), benzoic acid (BZ) and combinations of SLS plus BZ and ABS plus BZ effectively inhibited formation of sulfate and acid when added in concentrations greater than 50 mg/l to inoculated 20 or 30% coal refuse slurries. Here 25 mg/l concentrations of SLS, ABS and ABS plus BZ stimulated acid production. Formic, hexanoic, oxalic, propionic, and pyruvic acids at 0.1% concentrations were also effective inhibitors. Four different lignin sulfonates were only slightly effective inhibitors at 0.1% concentrations. It was concluded that acid formation resulting from microbial oxidation in high-sulfur coal refuse can be inhibited. 22 references.

In situ bioremediation (natural attenuation) at a gas plant waste site

International Nuclear Information System (INIS)

Ginn, J.S.; Sims, R.C.

1995-01-01

A former manufactured gas plant (MGP) waste site in New York was evaluated with regard to natural attenuation of polycyclic aromatic hydrocarbons (PAHs). Parent-compound concentrations of PAHs within an aquifer plume were observed to decrease with time subsequent to source removal of coal tar. Biotransformation-potential studies indicated that indigenous microorganisms in soil from the site were capable of degrading naphthalene and phenanthrene. A biochemical metabolite of phenanthrene degradation, 1-hydroxy-2-naphthoic acid (1H2NA), was tentatively characterized in coal-tar-contaminated soil from the site-based on liquid chromatographic retention time. Kinetic information was developed for the disappearance of phenanthrene and 1H2NA in nonspiked contaminated soil at the site. The Microtox trademark bioassay was used to evaluate toxicity trends in contaminated soil at the site. Results from the Microtox trademark indicated a decreasing trend in toxicity with respect to time in contaminated site soil. Research results were evaluated with regard to the National Research Council's guidelines for evaluating in situ bioremediation, and were used to enhance site characterization and monitoring information for evaluating the role of bioremediation as part of natural attenuation of PAHs at coal-tar-contaminated sites

Gasification of municipal solid waste in a downdraft gasifier: Analysis of tar formation

Directory of Open Access Journals (Sweden)

Tabitha Geoffrey Etutu

2016-04-01

Full Text Available In this study, municipal solid waste (MSW from a dumpsite was converted into refuse derived fuel (RDF and used as feedstock for an air-blown gasification process. The gasification process was conducted in a 10 kg.hr -1 downdraft gasifier at different air flow rates of 300, 350, 400, 450 and 550 NL.min1 at atmospheric pressure in order to investigate the quantity and quality of tar formed. It was shown that the increase in the air flow rate from 300 NL.min1 to 550 NL.min1 led to an increase in the oxidation temperature from 719°C to 870°C and an increase in the reduction temperature from 585°C to 750°C, respectively. Tar was reduced from 15 g.Nm3 to 4.7 g.Nm3 respectively. Heavy tar compounds (>C17 e.g. pyrene and phenathrene, decreased with the increase in the light tar compounds (tar reduction through a tar cracking process.

The Effect of Substrate Contaminates on the Life of Epoxy Coatings Submerged in Sea Water

Science.gov (United States)

1991-03-01

contaminants: coal tar, SovaPon, Mare Island and Aquapon . Aquapon is a clear (unpigmented) polyamide epoxy coating. While Aquapon is not normally used for...pigmented coatings. It was found that the Aquapon and coal tar coatings performed similarly, and blistered to the same extent, at the contamination levels...used in the test program. The Sovapon and Mare Island coatings were slightly more resistive to blistering when compared to Aquapon or coal tar but they

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

Inhaled smoke volume and puff indices with cigarettes of different tar and nicotine levels

International Nuclear Information System (INIS)

Woodman, G.; Newman, S.P.; Pavia, D.; Clarke, S.W.

1987-01-01

Ten asymptomatic smokers each smoked a low, low-to-middle and a middle tar cigarette with approximately the same tar-to-nicotine ratio, in a randomised order. The inhaled smoke volume was measured by tracing the smoke with the inert gas 81 Kr m . Puffing indices were recorded using an electronic smoking analyser and flowhead/cigarette holder. Throughout the study neither the mean inhaled smoke volume per puff nor the total inhaled smoke volume per cigarette changed significantly; however, the mean and total puff volumes were largest with the low tar cigarette and decreased with the higher tar brands. Puff volume was related to puff work (r s =0.83,P s =0.10,P>0.1). It is concluded that when switched between brands with the same tar-to-nicotine ratio, smokers increase their puff volumes with a lower tar cigarette but do not change the volume of smoke inhaled. Puff work and puff resistance were significantly correlated (r s =0.45,P<0.02). (author)

Analysis of low-temperature tar fractions

Energy Technology Data Exchange (ETDEWEB)

Kikkawa, S; Yamada, F

1952-01-01

A preliminary comparative study was made on the applicability of the methods commonly used for the type analysis of petroleum products to the low-temperature tar fractions. The usability of chromatography was also studied.

Physicochemical pretreatments and hydrolysis of furfural residues via carbon-based sulfonated solid acid.

Science.gov (United States)

Ma, Bao Jun; Sun, Yuan; Lin, Ke Ying; Li, Bing; Liu, Wan Yi

2014-03-01

Potential commercial physicochemical pretreatment methods, NaOH/microwave and NaOH/ultrasound were developed, and the carbon-based sulfonated solid acid catalysts were prepared for furfural residues conversion into reducing sugars. After the two optimum pretreatments, both the content of cellulose increased (74.03%, 72.28%, respectively) and the content of hemicellulose (94.11%, 94.17% of removal rate, respectively) and lignin (91.75%, 92.09% of removal rate, respectively) decreased in furfural residues. The reducing sugar yields of furfural residues with the two physicochemical pretreatments on coal tar-based solid acid reached 33.94% and 33.13%, respectively, higher than that pretreated via NaOH alone (27%) and comparable to that pretreated via NaOH/H2O2 (35.67%). The XRD patterns, IR spectra and SEM images show microwave and ultrasound improve the pretreatment effect. The results demonstrate the carbon-based sulfonated solid acids and the physicochemical pretreatments are green, effective, low-cost for furfural residues conversion. Copyright © 2014 Elsevier Ltd. All rights reserved.

An overview of the western Maryland coal combustion by-products/acid mine drainage initiative, Part 1 of 3

International Nuclear Information System (INIS)

Petzrick, P.; Rafalko, L.G.; Lyons, C.

1996-01-01

The western Maryland coal combustion by-products (CCB)/acid mine drainage (AMD) initiative (the Initiative) is a public-private partnership exploring the use of CCBs to eliminate AMD from Maryland's abandoned coal mines. This dynamic partnership will sponsor a series of large scale experiments and demonstrations addressing the engineering problems that characterize the beneficial application of CCBs to prevent acid formation on a scale that is consistent with the large quantity of these materials that will be produced by power plants in or near western Maryland. The initial demonstration is the filling and sealing of a small hand dug mine (the Frazee Mine) under approximately ninety feet of overburden on Winding Ridge near Friendsville, Maryland. A second demonstration is being planned for the Kempton mine complex. Subsequent demonstrations will focus on reducing the cost of materials handling and mine injection and solving the engineering problems characteristic of filling abandoned mines in Maryland. The Initiative is the flagship activity in Maryland's overall Ash Utilization Program, the goal of which is to promote beneficial use of all coal combustion by-products

Simulation of Trajectories of Tar Ball Transport to the Goa Coast

Digital Repository Service at National Institute of Oceanography (India)

Suneel, V.; Vethamony, P.; VinodKumar, K.; Babu, M.T.; Prasad, V.S.R.

Arrival of tar balls to the Goa coast during pre- and southwest monsoon seasons has been a regular phenomenon in the past few years. In one such event, we observed tar ball deposits along the Goa coast during August 2010, April 2011 and May 2011...

The Legend of Hot Tar or Pitch as a Defensive Weapon

DEFF Research Database (Denmark)

Atzbach, Rainer

2015-01-01

research. In reality, this way of fighting can only be seen as a legend, i.e. a story with only a relative truth at its core. This paper will examine the origin of this historical tradition and its archaeological and architectural sources. The chemical and physical properties of tar pitch and its...... production and use during the Middle Ages will be discussed with special focus on the application of tar pitch as an ingredient in medieval and post-medieval thermal weapons (especially Greek Fire, the firebomb and the fire arrow). The punishment of tarring and feathering will also be considered...

Ensamblajes urbanos: la TAR y el examen de la ciudad

Directory of Open Access Journals (Sweden)

Ignacio Farías

2011-03-01

Full Text Available Este artículo presenta nuevas perspectivas de investigación y desafíos analíticos que la teoría del actor-red (TAR abre para los estudios urbanos. En primer lugar, se revisan cómo los principios de relacionalidad híbrida y asociatividad plana de la TAR están siendo adoptados en los estudios urbanos para ampliar simétricamente la ecología urbana a no-humanos e impugnar concepciones escalares del espacio y economías urbanas. A continuación, se propone que la TAR trae consigo un desafío más fundamental relativo a la concepción de la ciudad como objeto de estudio. Mientras su comprensión habitual como objeto espacial, entidad político-económica y/o forma sociocultural subraya su carácter singular, estable y delimitado, la TAR permite pensar la ciudad como un objeto múltiple y decentrado. La noción de ensamblajes urbanos se introduce entonces para dar cuenta de la circulación y devenir de la ciudad en múltiples redes híbridas y translocales. El artículo concluye sopesando algunas de las consecuencias de este exámen de la ciudad, especialmente el reposicionamiento del problema de la complejidad, urbana en este caso, como punto, si no de partida, entonces al menos de llegada para la TAR.

Co-pyrolysis of coal with organic solids

Energy Technology Data Exchange (ETDEWEB)

Straka, P.; Buchtele, J. [Inst. of Rock Structure and Mechanics, Prague (Czechoslovakia)

1995-12-01

The co-pyrolysis of high volatile A bituminous coal with solid organic materials (proteins, cellulose, polyisoprene, polystyrene, polyethylene-glycolterephtalate-PEGT) at a high temperature conditions was investigated. Aim of the work was to evaluate, firstly, the changes of the texture and of the porous system of solid phase after high temperature treatment in presence of different types of macromolecular solids, secondly, properties and composition of the tar and gas. Considered organic solids are important waste components. During their co-pyrolysis the high volatile bituminous coal acts as a hydrogen donor in the temperature rank 220-480{degrees}C. In the rank 500- 1000{degrees}C the solid phase is formed. The co-pyrolysis was carried out at heating rate 3 K/min. It was found that an amount of organic solid (5-10%) affects important changes in the optical texture forms of solid phase, in the pore distribution and in the internal surface area. Transport large pores volume decreases in presence of PEGT, polystyrene and cellulose and increases in presence of proteins and polyisoprene. (image analysis measurements show that the tendency of coal to create coarse pores during co-pyrolysis is very strong and increases with increasing amount of organic solid in blend). An addition of considered materials changes the sorption ability (methylene blue test, iodine adsorption test), moreover, the reactivity of the solid phase.

Warm Cleanup of Coal-Derived Syngas: Multicontaminant Removal Process Demonstration

Energy Technology Data Exchange (ETDEWEB)

Spies, Kurt A.; Rainbolt, James E.; Li, Xiaohong S.; Braunberger, Beau; Li, Liyu; King, David L.; Dagle, Robert A.

2017-02-15

Warm cleanup of coal- or biomass-derived syngas requires sorbent and catalytic beds to protect downstream processes and catalysts from fouling. Sulfur is particularly harmful because even parts-per-million amounts are sufficient to poison downstream synthesis catalysts. Zinc oxide (ZnO) is a conventional sorbent for sulfur removal; however, its operational performance using real gasifier-derived syngas and in an integrated warm cleanup process is not well reported. In this paper, we report the optimal temperature for bulk desulfurization to be 450oC, while removal of sulfur to parts-per-billion levels requires a lower temperature of approximately 350oC. Under these conditions, we found that sulfur in the form of both hydrogen sulfide and carbonyl sulfide could be absorbed equally well using ZnO. For long-term operation, sorbent regeneration is desirable to minimize process costs. Over the course of five sulfidation and regeneration cycles, a ZnO bed lost about a third of its initial sulfur capacity, however sorbent capacity stabilized. Here, we also demonstrate, at the bench-scale, a process and materials used for warm cleanup of coal-derived syngas using five operations: 1) Na2CO3 for HCl removal, 2) regenerable ZnO beds for bulk sulfur removal, 3) a second ZnO bed for trace sulfur removal, 4) a Ni-Cu/C sorbent for multi-contaminant inorganic removal, and 5) a Ir-Ni/MgAl2O4 catalyst employed for ammonia decomposition and tar and light hydrocarbon steam reforming. Syngas cleanup was demonstrated through successful long-term performance of a poison-sensitive, Cu-based, water-gas-shift catalyst placed downstream of the cleanup process train. The tar reformer is an important and necessary operation with this particular gasification system; its inclusion was the difference between deactivating the water-gas catalyst with carbon deposition and successful 100-hour testing using 1 LPM of coal-derived syngas.

Development of Graft Copolymer Flocculant Based on Acrylamide and Acrylic Acid for the dewatering of coal

International Nuclear Information System (INIS)

Mahmoud, G.A.; Abdel Khalek, M.A

2012-01-01

Most coal preparation processes were carried out in water medium. The water content of coal product has a negative impact on handling and specific energy value. The moisture content may be attributed to the proportion of fine coal, which presents the greatest dewatering problem. A novel polymeric flocculant has been developed by graft copolymerization of acrylamide (AAm) with acrylic acid (AAc) using gamma irradiation technique. The grafted copol621621ymer P(AAm/AAc) was characterized by Fourier-transform infrared spectroscopy (FTIR), and thermo-gravimetric analysis (TGA). The effects of reaction parameters, such as total absorbed dose, and monomer concentration on grafting yield were investigated. The flocculation performance of the graft copolymer P(AAm/AAc) was investigated in coal suspension. It was observed that the grafting ratio was one of the key factors for the flocculating effects. The copolymers with various grafting ratios showed different flocculating properties. It was found that as the grafting ratio increased, the flocculating effect also increased. The flocculation performance of the grafted copolymer was better than that of the commercial flocculant, poly-acrylamide (Magnafloc 1011).

Cavities as the sources of acid mine process in the Niwka-Modrzejow Coal Mine (poland)

International Nuclear Information System (INIS)

Pluta, I.; Mazurkiewicz, M.

2005-01-01

Acid mine process is one of the most significant sources the pollution of surface water. The intensive process was discovered in the Niwka-Modrzejow Coal Mine at the level 100-130 m. In this paper the method of prevention by the filling cavities of wastes from energy plants was proposed. (authors)

Identification of sources of tar balls deposited along the Goa coast, India, using fingerprinting techniques

International Nuclear Information System (INIS)

Suneel, V.; Vethamony, P.; Zakaria, M.P.; Naik, B.G.; Prasad, K.V.S.R.

2013-01-01

Highlights: ► This is first fingerprinting study in India on identification of source of tar balls. ► Tar balls were formed from tanker-wash spills and they resemble floating tar ball. ► δ 13 C values of Bombay High crude oil and the present tar balls do not match. ► Compound specific stable carbon isotope analysis confirmed the source of tar balls. ► Source is confirmed as the South East Asian Crude Oil and not the Bombay High crude. -- Abstract: Deposition of tar balls along the coast of Goa, India is a common phenomenon during the southwest monsoon. Representative tar ball samples collected from various beaches of Goa and one Bombay High (BH) crude oil sample were subjected to fingerprint analysis based on diagnostic ratios of n-alkane, biomarkers of pentacyclic tri-terpanes and compound specific stable carbon isotope (δ 13 C) analysis to confirm the source. The results were compared with the published data of Middle East Crude Oil (MECO) and South East Asian Crude Oil (SEACO). The results revealed that the tar balls were from tanker-wash derived spills. The study also confirmed that the source is not the BH, but SEACO. The present study suggests that the biomarkers of alkanes and hopanes coupled with stable carbon isotope analysis act as a powerful tool for tracing the source of tar balls, particularly when the source specific biomarkers fail to distinguish the source

A review of the primary measures for tar elimination in biomass gasification processes

International Nuclear Information System (INIS)

Devi, Lopamudra; Ptasinski, K.J.; Janssen, F.J.J.G.

2003-01-01

Tar formation is one of the major problems to deal with during biomass gasification. Tar condenses at reduced temperature, thus blocking and fouling process equipments such as engines and turbines. Considerable efforts have been directed on tar removal from fuel gas. Tar removal technologies can broadly be divided into two approaches; hot gas cleaning after the gasifier (secondary methods), and treatments inside the gasifier (primary methods). Although secondary methods are proven to be effective, treatments inside the gasifier are gaining much attention as these may eliminate the need for downstream cleanup. In primary treatment, the gasifier is optimized to produce a fuel gas with minimum tar concentration. The different approaches of primary treatment are (a) proper selection of operating parameters, (b) use of bed additive/catalyst, and (c) gasifier modifications. The operating parameters such as temperature, gasifying agent, equivalence ratio, residence time, etc. play an important role in formation and decomposition of tar. There is a potential of using some active bed additives such as dolomite, olivine, char, etc. inside the gasifier. Ni-based catalyst are reported to be very effective not only for tar reduction, but also for decreasing the amount of nitrogenous compounds such as ammonia. Also, reactor modification can improve the quality of the product gas. The concepts of two-stage gasification and secondary air injection in the gasifier are of prime importance. Some aspects of primary methods and the research and development in this area are reviewed and cited in the present paper

Thermodynamic studies of a series of homologous HIV-1 TAR RNA ligands reveal that loose binders are stronger Tat competitors than tight ones.

Science.gov (United States)

Pascale, Lise; Azoulay, Stéphane; Di Giorgio, Audrey; Zenacker, Laura; Gaysinski, Marc; Clayette, Pascal; Patino, Nadia

2013-06-01

RNA is a major drug target, but the design of small molecules that modulate RNA function remains a great challenge. In this context, a series of structurally homologous 'polyamide amino acids' (PAA) was studied as HIV-1 trans-activating response (TAR) RNA ligands. An extensive thermodynamic study revealed the occurence of an enthalpy-entropy compensation phenomenon resulting in very close TAR affinities for all PAA. However, their binding modes and their ability to compete with the Tat fragment strongly differ according to their structure. Surprisingly, PAA that form loose complexes with TAR were shown to be stronger Tat competitors than those forming tight ones, and thermal denaturation studies demonstrated that loose complexes are more stable than tight ones. This could be correlated to the fact that loose and tight ligands induce distinct RNA conformational changes as revealed by circular dichroism experiments, although nuclear magnetic resonance (NMR) experiments showed that the TAR binding site is the same in all cases. Finally, some loose PAA also display promising inhibitory activities on HIV-infected cells. Altogether, these results lead to a better understanding of RNA interaction modes that could be very useful for devising new ligands of relevant RNA targets.

Study of the equilibrium of air-blown gasification of biomass to coal evolution fuels

International Nuclear Information System (INIS)

Biagini, Enrico

2016-01-01

Highlights: • Equilibrium model validated for coals, torrefied/green biomasses, in different gasifiers. • Maps of syngas composition, LHV and CGE for ER = 0–0.6, T = 500–2000 K, EBP = 0.004–0.158. • Effect of unconverted carbon, fuel moisture and overoxidation quantified. • Parameters for the maximum efficiency determined as functions of EBP. • EBP proven to be a good parameter for the quantitative comparison of different fuels. - Abstract: A non-stoichiometric equilibrium model based on the minimization of the Gibbs free energy was used to study the isothermal and adiabatic air-blown gasification of solid fuels on a carbonization curve from fossil (hard/brown coals, peat) to renewable (green biomasses and cellulose) fuels, including torrefied biofuels. The maps of syngas composition, heating value and process efficiency were provided as functions of equivalent ratio (oxygen-to-fuel ratio) in the range 0–0.6, temperature in 500–2000 K, and a fuel parameter, which allowed different cases to be quantitatively compared. The effect of fuel moisture, unconverted carbon and conditions to limit the tar formation was also studied. Cold gas efficiency >0.75 can be achieved for coals at high temperature, using entrained beds (which give low unconverted carbon), and improved by moisture/added steam. The bigger efficiency of green biomasses is only potential, as the practical limits (high temperature required to limit tar formation, moisture content and unconverted carbon in small gasifiers) strongly reduce the gasification performance. Torrefied biomasses (and plastics having an intermediate fuel parameter between coals and green biomasses) can attain high efficiency also in real conditions. The results shown in this work can be useful to evaluate the most promising feedstock (depending on its composition and possible pre-treatment/upgrading), define the operating conditions for maximizing the syngas heating value or the global efficiency, assess the

Solid state 13 C NMR quantitative study of wood tar pitches

International Nuclear Information System (INIS)

Prauchner, Marcos Juliano; Pasa, Vanya Marcia Duarte; Menezes, Sonia Maria Cabral de

1999-01-01

In this work, solid-state 13 C NMR is used with other techniques to characterize Eucalyptus tar pitches and to follow their polymerization reactions. The pitches are the residues of distillation (about 50% m;m) of the tar generated in Eucalyptus slow pyrolysis for charcoal production in metal industry

Create a Consortium and Develop Premium Carbon Products from Coal

Energy Technology Data Exchange (ETDEWEB)

Frank Rusinko; John Andresen; Jennifer E. Hill; Harold H. Schobert; Bruce G. Miller

2006-01-01

The objective of these projects was to investigate alternative technologies for non-fuel uses of coal. Special emphasis was placed on developing premium carbon products from coal-derived feedstocks. A total of 14 projects, which are the 2003 Research Projects, are reported herein. These projects were categorized into three overall objectives. They are: (1) To explore new applications for the use of anthracite in order to improve its marketability; (2) To effectively minimize environmental damage caused by mercury emissions, CO{sub 2} emissions, and coal impounds; and (3) To continue to increase our understanding of coal properties and establish coal usage in non-fuel industries. Research was completed in laboratories throughout the United States. Most research was performed on a bench-scale level with the intent of scaling up if preliminary tests proved successful. These projects resulted in many potential applications for coal-derived feedstocks. These include: (1) Use of anthracite as a sorbent to capture CO{sub 2} emissions; (2) Use of anthracite-based carbon as a catalyst; (3) Use of processed anthracite in carbon electrodes and carbon black; (4) Use of raw coal refuse for producing activated carbon; (5) Reusable PACs to recycle captured mercury; (6) Use of combustion and gasification chars to capture mercury from coal-fired power plants; (7) Development of a synthetic coal tar enamel; (8) Use of alternative binder pitches in aluminum anodes; (9) Use of Solvent Extracted Carbon Ore (SECO) to fuel a carbon fuel cell; (10) Production of a low cost coal-derived turbostratic carbon powder for structural applications; (11) Production of high-value carbon fibers and foams via the co-processing of a low-cost coal extract pitch with well-dispersed carbon nanotubes; (12) Use of carbon from fly ash as metallurgical carbon; (13) Production of bulk carbon fiber for concrete reinforcement; and (14) Characterizing coal solvent extraction processes. Although some of the

Avoiding tar formation in biocoke production from waste biomass

International Nuclear Information System (INIS)

Adrados, A.; De Marco, I.; Lopez-Urionabarrenechea, A.; Solar, J.; Caballero, B.

2015-01-01

This paper focuses in avoiding tar formation and in optimizing pyrolysis gas (maximizing H 2 and CO) in the production of biocoke from waste lignocellulosic biomass. In order to obtain metallurgical grade biochar (biocoke) slow heating rate and high temperature are required. Under such conditions useless pyrolysis liquids, mainly composed of water together with some heavy-sticky tars, are obtained. In order to make biocoke a cost-effective process it is necessary to optimize pyrolysis vapors avoiding tar formation and maximizing the amount and quality of both coke and gases. With this objective, in this work different heating rates (3–20 °C min −1 ) and catalysts (zeolite, Ni/CeO 2 –Al 2 O 3 ) have been tested in a two step pyrolysis process. Olive tree cuttings have been pyrolyzed in a 3.5 L batch reactor at 750 °C and the vapors generated have been thermally and catalytically treated at 900 °C in a second tubular reactor. About 25 wt.% biocoke useful as reducing agent in certain metallurgical processes, ≈57 wt.% gases with near 50 vol.% H 2 , and no tar production has been achieved when a heating rate of 3 °C min −1 and the homemade Ni/CeO 2 –Al 2 O 3 catalyst were used. - Highlights: • Metallurgical grade biochar was obtained by olive waste pyrolysis. • Low heating rates avoid tar formation and increase gas and biochar yields. • Ni/CeO 2 –Al 2 O 3 was better than HZSM5 zeolite for vapor upgrading in a second step. • Ni/CeO 2 –Al 2 O 3 and 3 °C min −1 gave the maximum H 2 , gas and biochar yields

Experimental and theoretical evaluation of the performance of a tar solar water heater

International Nuclear Information System (INIS)

Ammari, H.D.; Nimir, Y.L.

2003-01-01

The paper presents an experimental and theoretical evaluation of the performance of a tar solar water heater and comparison with that of a conventional type collector. The performance of both collectors is assessed under the same conditions. Both of the collectors have the same surface area and are glazed. The conventional type has the water tubes welded to the absorber plate, whereas in the tar type, the tar acts as an absorber plate that covers the water tubes. The theoretical model for each collector type, with the transient effects taken into account, is based on a control volume and a time base in the related energy equations. By considering a small element of the collector in each case, three partial differential equations were developed for each collector and were solved numerically by the Runge-Kutta method of the fifth order. A good agreement was achieved between the numerical and experimental results for both the conventional and tar collectors, indicating the feasibility of employing the theoretical model in the design of flat plate solar collectors. The results also showed that the conventional collector is more efficient than the tar type during most of the daylight, but the tar collector had the added advantage of better conservation of energy in late afternoon and evening

Sulfur transformation during rapid hydropyrolysis of coal under high pressure by using a continuous free fall pyrolyzer

Energy Technology Data Exchange (ETDEWEB)

W.-C. Xu; M. Kumagai

2003-02-01

The behavior of sulfur transformation during rapid hydropyrolysis of coal was investigated using a pressurized, continuous free fall pyrolyzer under the conditions of temperature ranging from 923 to 1123 K and hydrogen pressure up to 5 MPa. The yields of sulfur converted to gas, tar and char were determined, together with the analyses of sulfur form distributions in coals and chars. The results showed that the decomposition of inorganic sulfur species was affected only by the temperature, while the increases in temperature and hydrogen pressure obviously enhanced the removal of organic sulfur from coal. The extent of organic sulfur removal was proportional to the coal conversion, depending on coal type. A significant retention of gaseous sulfur products by the organic matrix of the char was observed during hydropyrolysis of a Chinese coal above 1023 K, even under the pressurized hydrogen atmosphere. The kinetic analysis indicates that the rate of organic sulfur removal from coal was 0.2th-order with respect to the hydrogen pressure, and the activation energy for total sulfur removal and organic sulfur removal is 17 26 and 13 55 kJ/mol, respectively. The low activation energies suggest that the transformation and removal of sulfur from coal might be controlled by the diffusion and/or thermodynamic equilibrium during hydropyrolysis under the pressurized conditions. 29 refs., 10 figs., 3 tabs.

Co-pyrolysis behaviour and kinetic of two typical solid wastes in China and characterisation of activated carbon prepared from pyrolytic char.

Science.gov (United States)

Ma, Yuhui; Niu, Ruxuan; Wang, Xiaona; Wang, Qunhui; Wang, Xiaoqiang; Sun, Xiaohong

2014-11-01

This is the first study on the co-pyrolysis of spent substrate of Pleurotus ostreatus and coal tar pitch, and the activated carbon prepared from the pyrolytic char. Thermogravimetry (TG) analysis was carried out taking spent substrate, coal tar pitch and spent substrate-coal tar pitch mixture. The activation energies of pyrolysis reactions were obtained via the Flynn-Wall-Ozawa and Kissinger-Akahira-Sunose methods. The kinetic models were determined by the master-plots method. The activated carbons were characterised by N2-adsorption, Fourier transform infrared spectroscopy and X-ray diffraction. Experimental results demonstrated a synergistic effect happened during co-pyrolysis, which was characterised by a decreased maximum decomposition rate and an enhanced char yield. The average activation energies of the pyrolysis reactions of spent substrate, coal tar pitch and the mixture were 115.94, 72.92 and 94.38 kJ mol(-1) for the Flynn-Wall-Ozawa method, and 112.17, 65.62 and 89.91 kJ mol(-1) for the Kissinger-Akahira-Sunose method. The reaction model functions were f(α) = (1-α)(3.42), (1-α)(1.72) and (1-α)(3.07) for spent substrate, coal tar pitch and the mixture, respectively. The mixture char-derived activated carbon had a Brunauer-Emmett-Teller surface area up to 1337 m(2) g(-1) and a total pore volume of 0.680 cm(3) g(-1). Mixing spent substrate with coal tar pitch led to the creation of more micropores and a higher surface area compared with the single spent substrate and coal tar pitch char. Also, the mixture char-derived activated carbon had a higher proportion of aromatic stacking. This study provides a reference for the utilisation of spent substrate and coal tar pitch via co-pyrolysis, and their pyrolytic char as a promising precursor of activated carbon. © The Author(s) 2014.

Structural determinants of HIV-1 nucleocapsid protein for cTAR DNA binding and destabilization, and correlation with inhibition of self-primed DNA synthesis.

Science.gov (United States)

Beltz, Hervé; Clauss, Céline; Piémont, Etienne; Ficheux, Damien; Gorelick, Robert J; Roques, Bernard; Gabus, Caroline; Darlix, Jean-Luc; de Rocquigny, Hugues; Mély, Yves

2005-05-20

The nucleocapsid protein (NC) of human immunodeficiency virus type 1 (HIV-1) is formed of two highly conserved CCHC zinc fingers flanked by small basic domains. NC is required for the two obligatory strand transfers in viral DNA synthesis through its nucleic acid chaperoning properties. The first DNA strand transfer relies on NC's ability to bind and destabilize the secondary structure of complementary transactivation response region (cTAR) DNA, to inhibit self-priming, and to promote the annealing of cTAR to TAR RNA. To further investigate NC chaperone properties, our aim was to identify by fluorescence spectroscopy and gel electrophoresis, the NC structural determinants for cTAR binding and destabilization, and for the inhibition of self-primed DNA synthesis on a model system using a series of NC mutants and HIV-1 reverse transcriptase. NC destabilization and self-priming inhibition properties were found to be supported by the two fingers in their proper context and the basic (29)RAPRKKG(35) linker. The strict requirement of the native proximal finger suggests that its hydrophobic platform (Val13, Phe16, Thr24 and Ala25) is crucial for binding, destabilization and inhibition of self-priming. In contrast, only partial folding of the distal finger is required, probably for presenting the Trp37 residue in an appropriate orientation. Also, Trp37 and the hydrophobic residues of the proximal finger appear to be essential for the propagation of the melting from the cTAR ends up to the middle of the stem. Finally, both N-terminal and C-terminal basic domains contribute to cTAR binding but not to its destabilization.

Abundance of dioxygenase genes similar to Ralstonia sp strain U2 nagAc is correlated with naphthalene concentrations in coal tar-contaminated freshwater sediments

Energy Technology Data Exchange (ETDEWEB)

Dionisi, H.M.; Chewning, C.S.; Morgan, K.H.; Menn, F.M.; Easter, J.P; Sayler, G.S. [University of Tennessee, Knoxville, TN (United States). Center for Environmental Biotechnology

2004-07-01

We designed a real-time PCR assay able to recognize dioxygenase large-subunit gene sequences with more than 90% similarity to the Ralstonia sp. strain U2 nagAc gene (nagAc-like gene sequences) in order to study the importance of organisms carrying these genes in the biodegradation of naphthalene. Sequencing of PCR products indicated that this real-time PCR assay was specific and able to detect a variety of nagAc-like gene sequences. One to 100 ng of contaminated-sediment total DNA in 25-{mu}l reaction mixtures produced an amplification efficiency of 0.97 without evident PCR inhibition. The assay was applied to surficial freshwater sediment samples obtained in or in close proximity to a coal tar-contaminated Superfund site. Naphthalene concentrations in the analyzed samples varied between 0.18 and 106 mg/kg of dry weight sediment. The assay for nagAc-like sequences indicated the presence of (4.1 {+-} 0.7) X 10{sup 3} to (2.9 {+-} 0.3) X 10{sup 5} copies of nagAc-like dioxygenase genes per mug of DNA extracted from sediment samples. These values corresponded to (1.2 {+-} 0.6) X 10{sup 5} to (5.4 {+-} 0.4) X 10{sup 7} copies of this target per g of dry weight sediment when losses of DNA during extraction were taken into account. There was a positive correlation between naphthalene concentrations and nagAc-like gene copies per microgram of DNA = 0.89) and per gram of dry weight sediment = 0.77). These results provide evidence of the ecological significance of organisms carrying nagAc-like genes in the biodegradation of naphthalene.

The acidic functional groups of humic acid

Energy Technology Data Exchange (ETDEWEB)

Shanxiang, Li; Shuhe, Sun; Zhai Zongxi, Wu Qihu

1983-09-01

The acidic functional groups content, pK value, DELTAH and DELTAS of humic acid (HA) and nitro-humic acid (NHA) were determined by potentiometry, conductometry and calorimetric titration. The thermodynamic parameters of carboxylic groups and phenolic hydroxyl groups of humic acid are similar to that of simple hydroxy-benzoic acid. The configuration sites of acidic functional groups in humic acid from different coals are different. The carbonyl groups on aromatic rings are probably ortho to phenolic -OH for HA and NHA extracted from Huangxian's brown coal and Japanese lignite, while those from Lingshi's weathered coal are not. The weak -COOH groups of the latter possess higher chemical activity. The -COOH content in HA increases, phenolic -OH group decreases and the chemical acidity of acidic functional groups increases when HA is oxidized by nitric acid. (14 refs.)

Tar Removal from Biomass Producer Gas by Using Biochar

DEFF Research Database (Denmark)

Ravenni, Giulia; Henriksen, Ulrik Birk; Ahrenfeldt, Jesper

2017-01-01

The biomass-derived char (biochar) produced in the gasifier as a residue, is a potential solution for removing tars from producer gas. This work investigates the interaction between tar compounds and biochar. Residual biochar from a TwoStage gasifier was tested as bed material in a laboratory setup....... Phenol and naphthalene were chosen as model tars, and entrained in a nitrogen flow. The gaseous stream was sampled before and after the biochar bed to evaluate the extent of conversion. The biochar bed (30g) was tested at 250°C, 500°C and 600°C, with for 3 consecutive hours. The compounds concentration...... in the gas phase was quantified by stable isotope dilution analysis, using Gas Chromatography-Mass Spectrometry (GC-MS). Results showed a significant effect of biochar on the removal of phenol, at all temperatures. Naphthalene was removed less efficiently at higher temperature, and this trend was even more...

Environmental assessment and nano-mineralogical characterization of coal, overburden and sediment from Indian coal mining acid drainage

Directory of Open Access Journals (Sweden)

Madhulika Dutta

2017-11-01

Full Text Available The deterioration of environmental conditions is the major contributory factor to poor health and quality of life that hinders sustainable development in any region. Coal mining is one of the major industries that contribute to the economy of a country but it also impacts the environment. The chemical parameters of the coal, overburden, soil and sediments along with the coal mine drainage (CMD were investigated in order to understand the overall environmental impact from high sulphur coal mining at northeastern coalfield (India. It was found that the total sulphur content of the coal is noticeably high compared to the overburden (OB and soil. The volatile matter of the coal is sufficiently high against the high ash content of the soil and overburden. The water samples have a High Electrical Conductivity (EC and high Total Dissolve Solid (TDS. Lower values of pH, indicate the dissolution of minerals present in the coal as well as other minerals in the mine rejects/overburden. The chemical and nano-mineralogical composition of coal, soil and overburden samples was studied using a High Resolution-Transmission Electron Microscopy (HR-TEM, Energy Dispersive Spectroscopy (EDS, Selected-Area Diffraction (SAED, Field Emission-Scanning Electron Microscopy (FE-SEM/EDS, X-ray diffraction (XRD, Fourier Transform Infrared Spectroscopy (FTIR, Raman and Ion-Chromatographic analysis, and Mössbauer spectroscopy. From different geochemical analysis it has been found that the mine water sample from Ledo colliery has the lowest pH value of 3.30, Tirap colliery samples have the highest electrical conductivity value of 5.40 ms cm−1. Both Ledo and Tirap coals have total sulphur contents within the range 3–3.50%. The coal mine water from Tirap colliery (TW-15B has high values of Mg2+ (450 ppm, and Br− (227.17 ppm. XRD analysis revealed the presence of minerals including quartz and hematite in the coals. Mineral analysis of coal mine overburden (OB indicates

Injection of alkaline ashes into underground coal mines for acid mine drainage abatement

International Nuclear Information System (INIS)

Aljoe, W.W.

1996-01-01

The injection of alkaline coal combustion waste products into abandoned underground coal mines for acid mine drainage (AMD) abatement has obvious conceptual appeal. This paper summarizes the findings of the baseline hydrogeologic and water quality evaluations at two sites--one in West Virginia and one in Maryland--where field demonstrations of the technique are being pursued in cooperative efforts among State and Federal agencies and/or private companies. The West Virginia site produces severe AMD from three to seven AMD sources that are spaced over about a 1.2 km stretch of the down-dip side of the mine workings. By completely filling the most problematic portion of the mine workings with coal combustion ashes, the State expects that the costs and problems associated with AMD treatment will be greatly reduced. At the Maryland site, it is expected that the AMD from a relatively small target mine will be eliminated completely by filling the entire mine void with a grout composed of a mixture of fly ash, fluidized-bed combustion ash, and flue gas desulfurization sludge. This project will also demonstrate the potential cost-effectiveness of the technique at other sites, both for the purpose of AMD remediation and control of land subsidence

Acidity of vapor plume from cooling tower mixed with flue gases emitted from coal-fired power plant.

Science.gov (United States)

Hlawiczka, Stanislaw; Korszun, Katarzyna; Fudala, Janina

2016-06-01

Acidity of products resulting from the reaction of flue gas components emitted from a coal-fired power plant with water contained in a vapor plume from a wet cooling tower was analyzed in a close vicinity of a power plant (710 m from the stack and 315 m from the cooling tower). Samples of this mixture were collected using a precipitation funnel where components of the mixed plumes were discharged from the atmosphere with the rainfall. To identify situations when the precipitation occurred at the same time as the wind directed the mixed vapor and flue gas plumes above the precipitation funnel, an ultrasound anemometer designed for 3D measurements of the wind field located near the funnel was used. Precipitation samples of extremely high acidity were identified - about 5% of samples collected during 12 months showed the acidity below pH=3 and the lowest recorded pH was 1.4. During the measurement period the value of pH characterizing the background acidity of the precipitation was about 6. The main outcome of this study was to demonstrate a very high, and so far completely underestimated, potential of occurrence of episodes of extremely acid depositions in the immediate vicinity of a coal-fired power plant. Copyright © 2016 Elsevier B.V. All rights reserved.

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

Analysis of the environmental control technology for tar sand development

Energy Technology Data Exchange (ETDEWEB)

de Nevers, N.; Glenne, B.; Bryner, C.

1979-06-01

The environmental technology for control of air pollution, water pollution, and for the disposal, stabilization, and vegetation of the waste tar sand were thoroughly investigated. Although some difficulties may be encountered in any of these undertakings, it seems clear that the air and water pollution problems can be solved to meet any applicable standard. Currently there are two large-scale plants producing liquid fuels from tar sands in Alberta, Canada which use similar technology involving surface mining, hot water extraction, and surface disposal of waste sand. These projects all meet the Canadian environmental control regulations in force at the time they began. The largest US deposits of tar sands are much smaller than the Canadian; 95 percent are located in the state of Utah. Their economics do not appear as attractive as the Canadian deposits. The environmental control costs are not large enough to make an otherwise economic project uneconomic. The most serious environmental conflict likely to occur over the recovery of liquid fuels from the US deposits of tar sands is that caused by the proximity of the deposits to national parks, national monuments, and a national recreation area in Utah. These areas have very stringent air pollution requirements; and even if the air pollution control requirements can be met, there may still be adequate opposition to large-scale mining ventures in these areas to prevent their commercial exploitation. Another environmental constraint may be water rights availability.Essentially all of the water running in the Colorado river basin is now legally allocated. Barring new interpretations of the legality of water rights purchase, Utah tar sands developments should be able to obtain water by purchasing existing irrigation water rights.