Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in Indonesia; Kankyo chowagata sekitan riyo system kanosei chosa. Indonesia ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of Indonesia, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/distribution/utilization and environmental problems, and analyzed the situation of the coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to work out a comprehensive master plan including Japan`s international cooperation for introducing the environmentally-friendly coal utilization system to Indonesia. Coal utilization systems, the introduction of which Indonesia should study in future, were picked up, according to the surveys in fiscal 1993 and 1994. In commercial/residential and small-scale industry sectors, needed is improvement of carbonization technology for production of coal carbonization briquette. Moreover, the introduction of bio-briquette should be studied in the future. In the power generation sector, studies should be made on the introduction of technology for SOx/NOx reduction and technology for coal ash treatment including the effective use of coal ash. For the introduction of coal boilers, the combustion mixed with bagasse, which is abundant in amount, is also necessary. In the coal production sector, coal preparation technology is studied, and a method to select the optimum process was proposed through the simulation. 76 figs., 43 tabs.

Application of artificial intelligence in coal preparation

Energy Technology Data Exchange (ETDEWEB)

Kuang, Y.; Deng, J.; Liu, H. [China University of Mining and Technology, Xuzhou (China). School of Chemical Engineering and Technology

2001-11-01

The general situation of using AI (Artificial intelligence) technology in coal preparation was introduced. The expert systems of coal preparation plant design, the expert management system of coal preparation plant, and the intelligent data-drawing bank were discussed. Some opinions about their foundation and method of knowledge expressing, inference, knowledge discovery of databases were presented. It is pointed out that an industrial system such as coal preparation is big and complex, so it is necessary and also difficult to use AI technology in these systems. Because the types of knowledge are different, there are various knowledge expressions and model of knowledge inference, hence only comprehensive methods suitable for the characters of the system may be used. 14 refs., 5 figs.

Tenth annual coal preparation, utilization, and environmental control contractors conference: Proceedings. Volume 1

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

Volume I contains papers presented at the following sessions: high efficiency preparation; advanced physical coal cleaning; superclean emission systems; air toxics and mercury measurement and control workshop; and mercury measurement and control workshop. Selected papers have been processed for inclusion in the Energy Science and Technology Database.

Critical paths to coal utilization

Energy Technology Data Exchange (ETDEWEB)

Hill, G R

1977-01-01

The present dilemma of energy producers, converters, and policy decision makers is presented. The consequences of environmental control regulations, coupled with the need for conservation and energy, and of energy resources on the increased utilization of coal, are discussed. Several recent technical accomplishments that make possible increased utilization of coal for power generation are described. Groundwork is laid for discussion of the technical development that must occur if the United States is to retain its energy viability.

30 CFR 827.13 - Coal preparation plants: Interim performance standards.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal preparation plants: Interim performance...-COAL PREPARATION PLANTS NOT LOCATED WITHIN THE PERMIT AREA OF A MINE § 827.13 Coal preparation plants: Interim performance standards. (a) Persons operating or who have operated coal preparation plants after...

Assessment of Research Needs for Coal Utilization

Energy Technology Data Exchange (ETDEWEB)

Penner, S.S.

1983-08-01

The Coal Combustion and Applications Working Group (CCAWG), at the request of J.W. Mares (Assistant Secretary for Fossil Energy) and A.W. Trivelpiece (Director, Office of Energy Research), has reviewed and evaluated the U.S. programs on coal combustion and utilization. The important topical areas of coal gasification and coal liquefaction have been deliberately excluded because R and D needs for these technologies were reviewed previously by the DOE Fossil Energy Research Working Group. The CCAWG studies were performed in order to provide an independent assessment of research areas that affect prospects for augmented coal utilization. In this report, we summarize the findings and research recommendations of CCAWG.

Coal Fly Ash Ceramics: Preparation, Characterization, and Use in the Hydrolysis of Sucrose

Directory of Open Access Journals (Sweden)

Ricardo Pires dos Santos

2014-01-01

Full Text Available Coal ash is a byproduct of mineral coal combustion in thermal power plants. This residue is responsible for many environmental problems because it pollutes soil, water, and air. Thus, it is important to find ways to reuse it. In this study, coal fly ash, obtained from the Presidente Médici Thermal Power Plant, was utilized in the preparation of ceramic supports for the immobilization of the enzyme invertase and subsequent hydrolysis of sucrose. Coal fly ash supports were prepared at several compaction pressures (63.66–318.30 MPa and sintered at 1200°C for 4 h. Mineralogical composition (by X-ray diffraction and surface area were studied. The ceramic prepared with 318.30 MPa presented the highest surface area (35 m2/g and amount of immobilized enzyme per g of support (76.6 mg/g. In assays involving sucrose inversion, it showed a high degree of hydrolysis (around 81% even after nine reuses and 30 days’ storage. Therefore, coal fly ash ceramics were demonstrated to be a promising biotechnological alternative as an immobilization support for the hydrolysis of sucrose.

Clean utilization of coal

International Nuclear Information System (INIS)

Yueruem, Y.

1992-01-01

This volume contains 23 lectures presented at the Advanced Study Institute on 'Chemistry and Chemical Engineering of Catalytic Solid Fuel Conversion for the Production of Clean Synthetic Fuels', which was held at Akcay, Edremit, Turkey, between 21 July and August 3, 1991. Three main subjects: structure and reactivity of coal; cleaning of coal and its products, and factors affecting the environmental balance of energy usage and solutions for the future, were discussed in the Institute and these are presented under six groups in the book: Part 1. Structure and reactivity of coal; Part 2. Factors affecting environmental balance; Part 3. Pre-usage cleaning operations and processes; Part 4. Upgrading of coal liquids and gases; Part 5. Oxygen enriched processes; and Part 6. Probable future solution for energy and pollution problems. Separate abstracts have been prepared for all the lectures

Present state in coal preparation. Stanje u pripremi uglja

Energy Technology Data Exchange (ETDEWEB)

Jevremovic, C. (Rudarsko-Geoloski Fakultet, Tuzla (Yugoslavia))

1990-01-01

Describes the low technological state of Yugoslav coal enterprises,in particular of those that exploit low grade lignite and brown coal with high ash and sulfur content. Unadjusted coal prices (almost the same price level for low and high energy coal) and absence of stringent laws on environmental pollution are regarded as main reasons for the low technological level of coal preparation and beneficiation plants. Modern preparation equipment for coal classification, coal washing, coal drying and briquetting is pointed out. Advanced coal carbonization and gasification should have a wider application in Yugoslavia for reducing environmental pollution and producing clean fuel.

An overview of coal preparation initiatives with application to coal conversion in South Africa

International Nuclear Information System (INIS)

Reinecke, C.F.; Bunt, J.R.

1999-01-01

in heating value, making then more suitable for use in power generation. From the foregoing it is clear that initiatives are currently underway in South Africa aimed at more effectively managing coal resources by maximizing the utilization potential thereof. It is the purpose of this paper to present an overview of Sasol's efforts aimed at more-effectively managing their coal resources, with particular emphasis on coal preparation

Feasibility survey of the environmentally-friendly coal utilization system. Feasibility survey of the environmentally-friendly coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

With relation to the coal of the Philippines, where the expansion of the use of coal as a substitute for petroleum/plant fuel is aimed at, the paper grasped the situation of coal production/development, the trend of coal import and domestic distribution, the coal utilization trend, and environmental problems, and analyzed the situation of coal utilization/spread by industry including the commercial/residential use. The purpose of the survey is to draw up a master plan for the introduction of the environmentally-friendly coal utilization system. As to the use of environmentally-friendly coal technology which should be adopted to the coal mining industry and commercial/residential sector, cited are the introduction of coal preparation technology and power transmission technology, and the development/spread of briquette as a firewood substituting fuel. In the electric power sector, the problem is the treatment of ash after combustion and the effective use. Relating to the treatment of flue gas, there is no installation at all of desulfurization facilities and denitrification facilities. In the cement industry sector, they wish to return fuel from heavy oil to coal. For it, it is necessary to study dust preventive measures. In the other sectors, coal hasn`t been used very much. An increase in coal demand is not expected also in the future, and big problems concerning coal haven`t occurred. 42 figs., 64 tabs.

Group separation of coal components and new ideas of coal utilization as petroleum

Energy Technology Data Exchange (ETDEWEB)

Zhi-hong Qin; Cui-li Hou; Juan Chen; Li-ying Zhang; Jie-qiong Ma [China University of Mining & Technology, Xuzhou (China). School of Chemical Engineering and Technology

2009-09-15

Four different groups of components were separated from coal under mild conditions of extraction and stripping process. Within these groups, and with pre-separation, individual utilization of all coal components can be realized, similar to petroleum components and enhance the inherent value and utilization value of coal, as well as increase environmental benefits. The characteristics of each component were analyzed with measurements by FTIR, GC/MS, TEM and the establishment of caking properties. The results show that coal can be separated into residues, ultra-pure coal, asphaltene components and light components by adding solvents for stripping into the CS{sub 2}/NMP mixed extraction solution. Those four groups of components present great differences in the presence of carbon and hydrogen elements, in the structure of functional groups, in their macroscopic structure and micro-morphology and caking properties. Every component possesses its own inherent values and approaches. A new idea of coal processes and utilization, similar to the use of petroleum is proposed. 11 refs., 6 figs., 6 tabs.

Fiscal 1997 survey report. Feasibility study of the environmentally friendly type coal utilization system (feasibility study of the environmentally friendly type coal utilization system in India); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Indo ni okeru kankyo chowagata sekitan riyo system kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The survey was conducted of the present situation of coal utilization and the present coal situation such as the environmental state of India which is a coal producing/consuming country next to China in Asia. The paper studied a feasibility of the introduction of the environmental friendly type coal utilization system` to be planned in India. The items for survey are the present situation of economy and energy and the future trend, environmental problems on coal utilization, the present status of the coal distribution system and study subjects, the present status of coal utilization by field and study subjects, a possibility of briquette use, a possibility of coal fluidization, electric power development plans and coal combustion technology in each industry, etc. The subjects are the obligation of coal preparation to coal thermal power plants 1000 km away from coal mines starting 2001, measures taken for effective ash use, measures taken for superannuated gas furnaces, etc. Based on the results of these site surveys and reports of the investigation under consignment from CMPDI, the paper studied/analyzed possibilities of introducing the coal utilization system having actual introduction results in Japan to India, and made an investigational report. 39 refs., 12 figs., 56 tabs.

Coal's sleeping market: non-utility generators

International Nuclear Information System (INIS)

McMahan, R.L.; Knutson, K.S.

1992-01-01

The article briefly profiles the coal market for non-utility generation (NUG). Coal consumption by NUGs, currently estimated at around 6.1 million tons, is projected to reach nearly 13.6 million tons by 1995 and 21.2 million tons by 2000. If the projected growth is achieved the NUG market may become one of the strongest market segments for the coal industry into the next century. 3 figs., 2 tabs

Fiscal 1997 feasibility survey of an environment friendly type coal utilization system. Feasibility survey of the environment friendly type coal utilization system in Malaysia and Vietnam (case of Vietnam); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Vietnam ban))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper grasped the state of coal utilization by coal consumption field, the state of coal physical flow in Vietnam, etc., surveyed/studied a possibility of introducing the environment friendly type coal utilization system, and assessed the possibility. As to energy resources, the north is abundant in hydroelectric and coal (mainly anthracite) resources, and the south in oil and natural gas resources. Coal production in fiscal 1997 is planned to be 10 million tons. Coal preparation technique presently available is only grain size sieving. Accordingly, it is necessary to study for heightening efficiency of facilities and modernizing facilities in accordance with the introduction of the environment friendly type coal utilization technology. During the study, it is possible to propose improvement on coal processing technology (coal preparation technology). Assessment and study are made especially of the coal selection system, fine coal recovery system and waste water treatment system. For the plan on new coal-fired power plants (300MWtimes4), there is left much necessity of proposing studying models considered of the anthracite combustion technology and environmental improvement and of assessing/studying them. 60 figs., 117 tabs.

Chemical analysis of coal by energy dispersive x-ray fluorescence utilizing artificial standards

International Nuclear Information System (INIS)

Wheeler, B.D.

1982-01-01

Accurate determinations of the elemental composition of coal by classical methods can be quite difficult and are normally very time consuming. X-ray fluorescence utilizing the powder method, however, has the ability of providing accurate and rapid analyses. Unfortunately, well characterized standards, although available, are not plentiful. In addition, the durability of stability of ground and pelletized coal samples is poor resulting in deterioration with time. As a result, artificial coal standards were prepared from certified geological materials by fusing in lithium tetraborate in percentages approximating expected ash contents and compositions in coal. Since the lithium tetraborate comprises about the same percentage of the standard as does the carbon, hydrogen, and oxygen in coal, the ground and pelletized coal sample can be assayed against the fused calibration curves by compensating for the differences in the mass absorption coefficients of the two matrices. 5 figures, 4 tables

Study on standard coal preparation plant for coking coal in Jharia Coalfield

Energy Technology Data Exchange (ETDEWEB)

Winiewski, J; Sarkar, G G

1975-10-01

The proposed standardization of coal preparation plant will be based on three standard types of crushing station, a standard jig washery or cyclone washery, and three standard types of slurry water treatment section. Some large installations, and some existing washeries after modification, may incorporate heavy media baths for coarse coal and jigs for slack coal, where coal is easy or moderately easy to wash. Flow sheets are given for the standard types of crushing plant, washery, and slurry water circuit. The storage of raw coal and saleable products is briefly discussed.

Advanced Acid Gas Separation Technology for the Utilization of Low Rank Coals

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, Jeff

2012-12-31

Air Products has developed a potentially ground-breaking technology – Sour Pressure Swing Adsorption (PSA) – to replace the solvent-based acid gas removal (AGR) systems currently employed to separate sulfur containing species, along with CO{sub 2} and other impurities, from gasifier syngas streams. The Sour PSA technology is based on adsorption processes that utilize pressure swing or temperature swing regeneration methods. Sour PSA technology has already been shown with higher rank coals to provide a significant reduction in the cost of CO{sub 2} capture for power generation, which should translate to a reduction in cost of electricity (COE), compared to baseline CO{sub 2} capture plant design. The objective of this project is to test the performance and capability of the adsorbents in handling tar and other impurities using a gaseous mixture generated from the gasification of lower rank, lignite coal. The results of this testing are used to generate a high-level pilot process design, and to prepare a techno-economic assessment evaluating the applicability of the technology to plants utilizing these coals.

Fiscal 2000 operation report. Fiscal 2000 model project for promoting advanced utilization of coal (Survey on data control system for advanced utilization of coal in Japan); 2000 nendo sekitan kodo riyo shuishin moderu jigyo gyomu hokokusho. Nihon no sekitan kodo riyo ni kakawaru data kanri system chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of contributing to the drafting of, for example, measures for securing coal resources for Japan and strategies for developing coal utilization technologies from the standpoint of the world climate of the coal supply/demand in the future, database was built concerning coal information such as coal-related supply/demand trend, technological development and utilization status in Japan and foreign countries, with the results of fiscal 2000 reported. In the preparation of related applications, a jump function in the case of pages unregistered with related subjects was added to the coal information retrieval system completed last year, as were a subdividing function of retrieval conditions and a link function to pages of a technical term dictionary. In the arrangement of the database classified by the fields, programs were prepared on 14 tables primarily in relation to supply and demand, with the collection, processing and registration of the data performed. In addition, in order to deal with the clarification of the patent licensing of GIF related technologies, there was developed a graph display program using a general-purpose language, Java. (NEDO)

6th Conference on Coal Utilization Technology; Dai 6 kai sekitan riyo gijutsu kaigi koenshu

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-09-01

The paper compiled the papers presented in the 6th Conference on Coal Utilization Technology held in September 1996. With relation to the fluidized bed boiler, reported were Field operation test of Wakamatsu PFBC combined cycle power plant and Development of pressurized internally circulating fluidized bed combustion technology. Regarding the coal reformation, Development of advanced coal cleaning process, Coal preparation and coal cleaning in the dry process, etc. Concerning the combustion technology, Study of the O2/CO2 combustion technology, Development of pressurized coal partial combustor, etc. About the CWM, Development of low rank coals upgrading and their CWM producing technology, Technique of CWM distribution system, etc. Relating to the coal ash, Engineering characteristics of the improved soil by deep mixing method using coal ash, Employment of fluidized bed ash as a basecourse material, On-site verification trials using fly ash for reclamation behind bulkheads, Water permeabilities of pulverized fuel ash, Separation of unburned carbon from coal fly ash through froth flotation, Practical use technology of coal ash (POZ-O-TEC), etc

Analysis of ecological environment impact of coal exploitation and utilization

Science.gov (United States)

Zhang, Baoliu; Luo, Hong; Lv, Lianhong; Wang, Jian; Zhang, Baoshi

2018-02-01

Based on the theory of life cycle assessment, the ecological and environmental impacts of coal mining, processing, utilization and transportation will be analyzed, with analysing the status of china’s coal exploitation and utilization as the basis, it will find out the ecological and environmental impact in the development and utilization of coal, mainly consist of ecological impact including land damage, water resource destructionand biodiversity loss, etc., while the environmental impact include air, water, solid waste pollutions. Finally with a summary of the ecological and environmental problems, to propose solutionsand countermeasures to promote the rational development and consumption of coal, as well as to reduce the impact of coal production and consumption on the ecological environment, finally to achieve the coordinated development of energy and the environment.

Controlling air toxics through advanced coal preparation

Energy Technology Data Exchange (ETDEWEB)

Straszheim, W.E.; Buttermore, W.H.; Pollard, J.L. [Iowa State Univ., Ames, IA (United States)

1995-11-01

This project involves the assessment of advanced coal preparation methods for removing trace elements from coal to reduce the potential for air toxic emissions upon combustion. Scanning electron microscopy-based automated image analysis (SEM-AIA) and advanced washability analyses are being applied with state-of-the-art analytical procedures to predict the removal of elements of concern by advanced column flotation and to confirm the effectiveness of preparation on the quality of quantity of clean coal produced. Specific objectives are to maintain an acceptable recovery of combustible product, while improving the rejection of mineral-associated trace elements. Current work has focused on determining conditions for controlling column flotation system across its operating range and on selection and analysis of samples for determining trace element cleanability.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper investigated and studied the present situation and future trend of coal utilization and distribution in Thailand, and the present situation of environmental effects and the measures taken for environmental protection. Around 2010, coal will probably be produced only at EGAT`s Mae Moh (MM) coal mine. Demand for overseas coal is expected to be 40-50 million tons in 2011, and preparation of the coal center becomes a subject. For general industry use coal, pretreatment such as coal preparation, coal blending and briquetting is needed, considering coal quality, usage, transport distance and environmental effects. Brown coal of MM coal mine is a lignite with high sulfur, high ash content and low heating value. Wide spread of its use can be expected if upgrading is possible such as desulfurization, deashing, increasing heating value. In the electric power generation field, the absorber was installed at the existing boiler of the mine-mouth generating plant to conduct a verification test on high grade desulfurization of ultra-high sulfur lignite. In the industry field, the circulating fluidized bed boiler was adopted. In the residential/commercial field, introduction of briquette was proposed. 80 refs., 84 tabs.

Geology in coal resource utilization

International Nuclear Information System (INIS)

Peters, D.C.

1991-01-01

The 37 papers in this book were compiled with an overriding theme in mind: to provide the coal industry with a comprehensive source of information on how geology and geologic concepts can be applied to the many facets of coal resource location, extraction, and utilization. The chapters have been arranged to address the major coal geology subfields of Exploration and Reserve Definition, Reserve Estimation, Coalbed Methane, Underground Coal Gasification, Mining, Coal Quality Concerns, and Environmental Impacts, with papers distributed on the basis of their primary emphasis. To help guide one through the collection, the author has included prefaces at the beginning of each chapter. They are intended as a brief lead-in to the subject of the chapter and an acknowledgement of the papers' connections to the subject and contributions to the chapter. In addition, a brief cross-reference section has been included in each preface to help one find papers of interest in other chapters. The subfields of coal geology are intimately intertwined, and investigations in one area may impact problems in another area. Some subfields tend to blur at their edges, such as with reserve definition and reserve estimation. Papers have been processed separately for inclusion on the data base

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

Coal comprehensive utilization is the gateway for Shanxi Province

International Nuclear Information System (INIS)

Ma, L.; Gui, G.

1997-01-01

Shanxi Province is abundant in coal reserve. Taiyuan Coal Gasification Corporation is a large sized union enterprise engaged in comprehensive use of coal in Shanxi province, and significant economic, social, environmental benefits have been brought forth with it. This leads people to believe that coal comprehensive utilization is the gateway for Shanxi Province in the fields of improvement of environment and development of economy

Clean Coal Day '94 Hokkaido International Seminar; Clean coal day '94 Hokkaido kokusai seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-06-01

The lectures given at the seminar were 1) Coal energy be friendly toward the earth, 2) Clean coal technology in the United Kingdom, and 3) How clean coal should be in Australia. In lecture 1), remarks are made on the importance of coal and its future, coal that protects forest, whether coal is a dirty fuel, coal combustion tests started relative to environmental pollution, acid rain in China and coal combustion, briquets effective in energy conservation, etc. In lecture 2), remarks are made on the importance of coal utilization in the United Kingdom, current state of coal utilization in power generation, problems related to gasification furnaces, problems related to combustors, problems related to high-temperature gas cleaning, function of cleaning filters, advantages of high-temperature gas treatment, actualities of gas combustors, studies of gas combustors, etc. In lecture 3), remarks are made on Australia's coal situation, problems related to clean coal technology, problems related to coal preparation technology, potentialities of Australian brown coal, coal utilization in power generation, need of new technology development, current state of coal utilization in Australia, coal utilization in metal-making industry, international cooperation on technology, etc. (NEDO)

Empirical prediction of ash deposition propensities in coal-fired utilities

Energy Technology Data Exchange (ETDEWEB)

Frandsen, F.

1997-01-01

This report contain an outline of some of the ash chemistry indices utilized in the EPREDEPO (Empirical PREdiction of DEPOsition) PC-program, version 1.0 (DEPO10), developed by Flemming Frandsen, The CHEC Research Programme, at the Department of Chemical Engineering, Technical University of Denmark. DEPO10 is a 1st generation FTN77 Fortran PC-programme designed to empirically predict ash deposition propensities in coal-fired utility boilers. Expectational data (empirical basis) from an EPRI-sponsored survey of ash deposition experiences at coal-fired utility boilers, performed by Battelle, have been tested for use on Danish coal chemistry - boiler operational conditions, in this study. (au) 31 refs.

Improvement in water-slurry circulation at the Chumakovskaya coal preparation plant

Energy Technology Data Exchange (ETDEWEB)

Nabokov, A.K.; Fedotov, B.P.; Mitlash, V.V.

1988-02-01

The Chumakovskaya coal preparation plant (Donetskugleobogashchenie association) was put into operation in 1935. It processes 570 t/h of coal slurry with an ash content of 38.6% and produces grade T coal for coking and power generation. Coal preparation technology used is described. Shortcomings of the system cause 130 kg of high ash slurries to be recirculated per m/sup 3/ of hydrocyclone drain. Mathematical analysis of the present process and of two improved variants is presented. The analysis permits variants for clarification of the recirculated water to be developed and evaluated and the best one to be selected. The optimum variant permits the amount of thin recirculated slurry to be reduced to 48% and the amount of granular slurry to 13%. Implementation of this variant at the Chumakovskaya coal preparation plant will ensure annual savings of 20,000 rubles.

Technical project of complex fast cycle heat treatment of hydrogenous coal preparation

OpenAIRE

Moiseev, V. A.; Andrienko, V. G.; Pileckij, V. G.; Urvancev, A. I.; Gvozdyakov, Dmitry Vasilievich; Gubin, Vladimir Evgenievich; Matveev, Aleksandr Sergeevich; Savostiyanova, Ludmila Viktorovna

2015-01-01

Problems of heat-treated milled hydrogenous coal preparation site creation in leading fast cycle heat treatment complex were considered. Conditions for effective use of electrostatic methods of heat-treated milled hydrogenous coal preparation were set. Technical project of heat treatment of milled hydrogenous coal preparation site was developed including coupling of working equipment complex on fast heat treatment and experimental samples of equipment being designed for manufacturing. It was ...

Energy-Saving Vibration Impulse Coal Degradation at Finely Dispersed Coal-Water Slurry Preparation

Directory of Open Access Journals (Sweden)

Moiseev V.A.

2015-01-01

Full Text Available Theoretical and experimental research results of processes of finely dispersed coal-water slurry preparation for further generation of energetic gas in direct flow and vortex gas generator plants have been presented. It has been stated that frequency parameters of parabolic vibration impulse mill influence degradation degree. Pressure influence on coal parameters in grinding cavity has been proven. Experimental researches have proven efficiency of vibration impulse mill with unbalanced mass vibrator generator development. Conditions of development on intergranular walls of coal cracks have been defined.

Coal and energy: a southern perspective. Regional characterization report for the National Coal Utilization Assessment

Energy Technology Data Exchange (ETDEWEB)

Boercker, F. D.; Davis, R. M.; Goff, F. G.; Olson, J. S.; Parzyck, D. C.

1977-08-01

This publication is the first of several reports to be produced for the National Coal Utilization Assessment, a program sponsored by the Assistant Administrator for Environment and Safety through the Division of Technology Overview of ERDA. The purpose of the report is to present the state and regional perspective on energy-related issues, especially those concerning coal production and utilization for 12 southern states. This report compiles information on the present status of: (1) state government infrastructure that deals with energy problems; (2) the balance between energy consumption and energy production; (3) the distribution of proved reserves of various mineral energy resources; (4) the major characteristics of the population; (5) the important features of the environment; and (6) the major constraints to increased coal production and utilization as perceived by the states and regional agencies. Many energy-related characteristics described vary significantly from state to state within the region. Regional and national generalizations obscure these important local variations. The report provides the state and regional perspective on energy issues so that these issues may be considered objectively and incorporated into the National Coal Utilization Assessment. This Assessment is designed to provide useful outputs for national, regional, and local energy planners.

Characterization of coal blends for effective utilization in thermal power plants

International Nuclear Information System (INIS)

Santhosh Raaj, S.; Arumugam, S.; Muthukrishnan, M.; Krishnamoorthy, S.; Anantharaman, N.

2016-01-01

Highlights: • This work will assist utilities to decide on the choice of coals for blending. • Conventional and advanced analytical techniques were used for characterization. • Fuel ratio, burnout profile, ash chemistry and carbon burnout are key factors. • Basic properties were additive while carbon burnout was non additive for the blends. - Abstract: This paper deals with the characterization of coal blends using various conventional and advanced analytical techniques. There has been an increasing trend in utilizing imported coals for power generation in India and utilities are resorting to blended coal firing for various reasons, both financially as well as technically. Characterization studies were carried out on 2 combinations of Indian and imported coal blends. Conventional characterization such as proximate and ultimate analysis and determination of calorific value were carried out for the raw coals and blends as per ASTM standards. Following this thermal and mineral analysis of the samples were carried out using thermo gravimetric analyzer (TGA), X-ray fluorescence spectrometer (XRF) and computer controlled scanning electron microscope (CCSEM). Combustion experiments were also conducted using drop tube furnace (DTF) to determine the burnout of the raw coals and blends. The selection of technically suitable coal combination for blending, based on these characterization studies, has been detailed.

Coal preparation and coal cleaning in the dry process; Kanshiki sentaku to coal cleaning

Energy Technology Data Exchange (ETDEWEB)

Tanaka, Z; Morikawa, M; Fujii, Y [Okayama University, Okayama (Japan). Faculty of Engineering

1996-09-01

Because the wet process has a problem such as waste water treatment, coal cleaning in the dry process was discussed. When a fluidized bed (using glass beads and calcium carbonate) is utilized instead of the heavy liquid, the fluidized bed will have apparent density as the liquid does, whereas the relative relationship therewith determines whether a substance having been put into the fluidized bed will float or sink. This is utilized for coals. In addition, two powder constituents of A and B may be wanted to be separated using the fluidized extraction process (similar to the liquid-liquid extraction process). In such a case, a fluidized bed in which both constituents are mixed is added with a third constituent C (which will not mix with A, but mix well with B), where the constituents are separated into A and (B + C), and the (B + C) constituent is separated further by using a sieve. If coal has the coal content mixed with ash content and pulverized, it turns into particle groups which have distributions in grain size and density. Groups having higher density may contain more ash, and those having lower density less ash. In addition, the ash content depends also on the grain size. The ash content may be classified by using simultaneously wind classification (for density and grain size) and a sieve (for grain size). This inference may be expanded to consideration of constructing a multi-stage fluidized bed classification tower. 12 figs., 5 tabs.

Overview of Turkey's coal necessity, reserves and utilization

Energy Technology Data Exchange (ETDEWEB)

Kilic, Ahmet Mahmut; Kilic, Ozen

2006-10-15

This article deals with overview of Turkey's coal necessity, reserves and utilization. Turkey is rapidly growing in terms of both its economy and its population. In parallel, its demand for energy, particularly for electricity, is increasing. Turkey possesses fossil fuel resources of hard coal (HC) and lignite (LG) have the greatest importance in energy production and for the national economy. The hard coal and lignite reserves of Turkey are 1.126 and 8.375 millions tons(Mt), respectively. Coal, the major fuel source for Turkey utilized mainly for electric power, steel manufacturing and cement production, amounts to 31% of total energy consumption in Turkey. To sum up, providing the total consumption is taken into account in the Middle East, the coal consumption rate of Turkey is approximately 90% of the consumption in this region.

Research program for an environmentally-friendly coal utilization system in the Philippines

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Feasibility studies are conducted on the introduction of an environmentally-friendly coal utilization system into the Filipino electric power industry, cement industry, and domestic fuel sector. The studies cover the current status of economy and energy in that country, supply and demand of coal, environmental protection and Government's policy, study of the above-said system relative to its application to the fields of electric power industry, cement industry, and domestic fuel sector, and a study about the effective utilization of Filipino domestic coal by the use of the system. Imported coal is used in the electric power industry because of its cost and quality. It is learned after research, however, that domestic coal will be able to compete against imported coal when some technologies are resorted to, such as those pertinent to denitrification in the furnace, novel low-NOx burner, coal pulverization, and combustion diagnosis. As for the treatment of flue gas, it is concluded that the simplified wet lime/gypsum process will be suitable. It is inferred that the CWM (coal-water mixture) process technology will be effective for the utilization of domestic low-grade coal. (NEDO)

Research program for an environmentally-friendly coal utilization system in the Philippines

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Feasibility studies are conducted on the introduction of an environmentally-friendly coal utilization system into the Filipino electric power industry, cement industry, and domestic fuel sector. The studies cover the current status of economy and energy in that country, supply and demand of coal, environmental protection and Government's policy, study of the above-said system relative to its application to the fields of electric power industry, cement industry, and domestic fuel sector, and a study about the effective utilization of Filipino domestic coal by the use of the system. Imported coal is used in the electric power industry because of its cost and quality. It is learned after research, however, that domestic coal will be able to compete against imported coal when some technologies are resorted to, such as those pertinent to denitrification in the furnace, novel low-NOx burner, coal pulverization, and combustion diagnosis. As for the treatment of flue gas, it is concluded that the simplified wet lime/gypsum process will be suitable. It is inferred that the CWM (coal-water mixture) process technology will be effective for the utilization of domestic low-grade coal. (NEDO)

Preparation of coal slurries deposited in ground settling ponds

Directory of Open Access Journals (Sweden)

Wiesław Blaschke

2005-11-01

Full Text Available As a result of the hard coal washing process, considerable quantities of coal slimes are generated. They belong to grain size classes below 1, 0 mm (with the majority of grains below 0,035 mm and are often sold in order to prepare blends for the power generation. It is assessed that in Poland about 11 mln tons of such slimes were deposited. The slimes of a low ash content can be exploited and sold. The slime of high ash content must be washed. In Poland there is one coal preparation plant for slurries. The article describes the technology and presents the results of a simplified economic analysis of exploitation of the slurries and their washing.

Effect of flotation on preparation of coal-water slurries

Energy Technology Data Exchange (ETDEWEB)

Ding, K.; Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada)

2009-07-01

In order to study the effect of flotation reagents on the properties of coal-water slurry, a sub-bituminous coal was cleaned via either forward flotation or reverse flotation. The froth product from the forward flotation, obtained with the use of diesel oil and MIBC, and the tailings of the reverse flotation, carried out with dextrin-tannic acid depressants and dodecyltrimethylammonium chloride collector, were used in the preparation of coal-water slurries. It was shown that while it was possible to obtain the coal-water slurry with a high-solids content from the coal rendered hydrophilic (tailings from the coal reverse flotation), in the case of the hydrophobic product (froth product from the forward flotation) a dispersing agent was required to obtain the coal-water slurry of the same high-solids content.

Self-scrubbing coal

International Nuclear Information System (INIS)

Kindig, J.K.

1992-01-01

More than 502 million tons - 65 percent of all coal shipped to utilities in 1990 - were above 1.2 pounds of sulfur dioxide per million Btu. Most of the coal, even though cleaned in conventional coal preparation plants, still does not meet the emission limitation the Clean Air Act Amendments mandate for the year 2000. To cope with this fact, most utilities plan to switch to low sulfur (western U.S. or Central Appalachian) coal or install scrubbers. Both solutions have serous drawbacks. Switching puts local miners out of work and weakens the economy in the utility's service territory. Scrubbing requires a major capital expenditure by the utility. Scrubbers also increase the operating complexity and costs of the generating station and produce yet another environmental problem, scrubber sludge. Employing three new cost-effective technologies developed by Customer Coals International (CCl), most non-compliance coals east of the Mississippi River can be brought into year-2000 compliance. The compliance approach employed, depends upon the characteristics of the raw coal. Three types of raw coal are differentiated, based upon the amount of organic sulfur in the coals and the ease (or difficultly) of liberating the pyrite. They are: Low organic sulfur content and pyrite that liberates easily. Moderate organic sulfur content and pyrite that liberates easily. High organic sulfur content or the pyrite liberates with difficulty. In this paper examples of each type of raw coal are presented below, and the compliance approach employed for each is described. The names of the beneficiated coal products produced from each type of raw coal give above are: Carefree Coal, Self-Scrubbing Coal and Dry-Scrubbing Coal

Geochemistry of Toxic Elements and Their Removal via the Preparation of High-Uranium Coal in Southwestern China

Directory of Open Access Journals (Sweden)

Piaopiao Duan

2018-02-01

Full Text Available High-uranium (U coal is the dominant form of coal in Southwestern China. However, directly utilizing this resource can also harm the environment because this element is radioactive; it is, therefore, necessary to clean this kind of coal before burning. This research studied the geochemistry of toxic elements and their partitioning during the preparation of high-U coal in China. The results show that high-U coals are mainly distributed in Southwestern China and are characterized by a high organic sulfur (S content and vanadium (V-chromium (Cr-molybdenum (Mo-U element assemblage. These elements are well-correlated with one another, but are all negatively related to ash yield, indicating that all four are syngenetic in origin and associated with organic materials. A mineralogical analysis shows that U in Ganhe and Rongyang coal occurs within fine-grained anatase, clay minerals, guadarramite, and pyrite, while V occurs in clay minerals, pyrite, and dolomite, and Cr occurs in dolomite. Other elements, such as fluorine (F, lead (Pb, selenium (Se, and mercury (Hg, mainly occur in pyrite. By applying a gravity separation method to separate minerals from coal, the content of the enrichment element assemblage of V-Cr-Mo-U in Rongyang coal is still shown to be higher than, or close to, that of the original feed because this element assemblage is derived from hydrothermal fluids during syngenetic or early diagenetic phases, but other elements (beryllium [Be], F, manganese [Mn], zinc [Zn], Pb, arsenic [As], Se, Hg can be efficiently removed. Once cleaned, the coal obtained by gravity separation was subject to a flotation test to separate minerals; these results indicate that while a portion of V and Cr can be removed, Mo and U remain difficult to extract. It is evident that the two most commonly utilized industrialized coal preparation methods, gravity separation and flotation, cannot effectively remove U from coal where this element occurs in large

Use of new ceramic linings in coal preparation plants

Energy Technology Data Exchange (ETDEWEB)

Fedorchenko, V.E.; Rudenko, V.A.; Bondarev, A.Ya.

1984-01-01

This article evaluates several materials used as liners in coal preparation equipment. The evaluations concentrate on liners used under conditions of intensive temperature fluctuations, e.g. liners of coal chutes for coal transport from coal dryers. Two aspects of wear are analyzed: abrasion by friction and effects of temperature fluctuations. Abrasive wear is tested using magnetite suspension with a density of 400 g/l. Tests show that abrasive wear of liners on an alumina basis is 3 times lower than abrasive wear of high quality steel, from 13 to 24 times lower than that of iron and from 6 to 8 times lower than that of steels used in coal preparation plants. Effects of temperature fluctuations from 20 to 840 C on abrasive wear of liners of steels, iron, slag glass ceramics, mullite-corundum material and corundum is shown in a table. The test show that mullite-corundum material on the basis of alumina is characterized by a high resistance to abrasive wear after 30 cycles of temperature increase from 20 to 840 C and decrease to 20 C. Using mullite-corundum as liners of equipment and installations operating under conditions of temperature fluctuations is recommended.

Why do electricity utilities cooperate with coal suppliers? A theoretical and empirical analysis from China

International Nuclear Information System (INIS)

Zhao Xiaoli; Lyon, Thomas P.; Wang Feng; Song Cui

2012-01-01

The asymmetry of Chinese coal and electricity pricing reforms leads to serious conflict between coal suppliers and electricity utilities. Electricity utilities experience significant losses as a result of conflict: severe coal price fluctuations, and uncertainty in the quantity and quality of coal supplies. This paper explores whether establishing cooperative relationships between coal suppliers and electricity utilities can resolve conflicts. We begin with a discussion of the history of coal and electricity pricing reforms, and then conduct a theoretical analysis of relational contracting to provide a new perspective on the drivers behind the establishment of cooperative relationships between the two parties. Finally, we empirically investigate the role of cooperative relationships and the establishment of mine-mouth power plants on the performance of electricity utilities. The results show that relational contracting between electricity utilities and coal suppliers improves the market performance of electricity utilities; meanwhile, the transportation cost savings derived from mine-mouth power plants are of importance in improving the performance of electricity utilities. - Highlights: ► We discuss the history of coal and electricity pricing reforms. ► The roots of conflicts between electricity and coal firms are presented. ► We conduct a theoretical analysis of relational contracting. ► The role of mine-mouth power plants on the performance of power firms is examined.

Environmental impact of coal utilization (from raw material to waste resources): Proceedings

International Nuclear Information System (INIS)

Sahu, K.C.

1991-10-01

The proceedings contains 27 papers presented at the conference on environmental impact of coal utilization from raw material to waste resources which was held at the Indian Institute of Technology, Bombay, during 14-15 January 1991. The conference was held as a follow-up of the research project to study the impact of coal utilization. The project was undertaken jointly by the Indian Institute of Technology, Bombay and the University of Western Ontario, Canada. The project was funded by the International Development Research Centre, Ottawa (Canada). The principle themes of the conference were : occurrence of trace elements in coal, fate of trace elements during combustion of coal, characterisation of fly ash and its properties and utilization, and environmental impact of ash disposal. (M.G.B.)

Petrographic and mineral characterization of Balkan coals and their solid waste products from coal preparation

International Nuclear Information System (INIS)

Yossifova, M.

1995-01-01

This paper is part of a complex petrographic, mineralogical and chemical investigation on Balkan bituminous coals and their solid waste products from coal preparation. The petrographic and phase-mineralogical composition in ten composite samples and four water extracts have been studied by optical microscopy, scanning electron microscopy and X-ray diffraction. 4 refs., 4 tabs

Comparative analysis of large biomass & coal co-utilization units

NARCIS (Netherlands)

Liszka, M.; Nowak, G.; Ptasinski, K.J.; Favrat, D.; Marechal, F.

2010-01-01

The co-utilization of coal and biomass in large power units is considered in many countries (e.g. Poland) as fast and effective way of increasing renewable energy share in the fuel mix. Such a method of biomass use is especially suitable for power systems where solid fuels (hard coal, lignite) are

Analysis of mineral phases in coal utilizing factor analysis

International Nuclear Information System (INIS)

Roscoe, B.A.; Hopke, P.K.

1982-01-01

The mineral phase inclusions of coal are discussed. The contribution of these to a coal sample are determined utilizing several techniques. Neutron activation analysis in conjunction with coal washability studies have produced some information on the general trends of elemental variation in the mineral phases. These results have been enhanced by the use of various statistical techniques. The target transformation factor analysis is specifically discussed and shown to be able to produce elemental profiles of the mineral phases in coal. A data set consisting of physically fractionated coal samples was generated. These samples were analyzed by neutron activation analysis and then their elemental concentrations examined using TTFA. Information concerning the mineral phases in coal can thus be acquired from factor analysis even with limited data. Additional data may permit the resolution of additional mineral phases as well as refinement of theose already identified

Structural characteristics and gasification reactivity of chars prepared from K{sub 2}CO{sub 3} mixed HyperCoals and coals

Energy Technology Data Exchange (ETDEWEB)

Atul Sharma; Hiroyuki Kawashima; Ikuo Saito; Toshimasa Takanohashi [National Institute of Advanced Industrial Science and Technology, Ibaraki (Japan). Advanced Fuel Group

2009-04-15

HyperCoal is a clean coal with mineral matter content <0.05 wt %. Oaky Creek (C = 82%), and Pasir (C = 68%) coals were subjected to solvent extraction method to prepare Oaky Creek HyperCoal, and Pasir HyperCoal. Experiments were carried out to compare the gasification reactivity of HyperCoals and parent raw coals with 20, 40, 50 and 60% K{sub 2}CO{sub 3} as a catalyst at 600, 650, 700, and 775{sup o}C with steam. Gasification rates of coals and HyperCoals were strongly influenced by the temperature and catalyst loading. Catalytic steam gasification of HyperCoal chars was found to be chemical reaction controlled in the 600-700{sup o}C temperature range for all catalyst loadings. Gasification rates of HyperCoal chars were found to be always higher than parent coals at any given temperature for all catalyst loadings. However, X-ray diffraction results showed that the microstructures of chars prepared from coals and HyperCoals were similar. Results from nuclear magnetic resonance spectroscopy show no significant difference between the chemical compositions of the chars. Significant differences were observed from scanning electron microscopy images, which showed that the chars from HyperCoals had coral-reef like structures whereas dense chars were observed for coals. 26 refs., 8 figs., 2 tabs.

Coal utilization, the environment, and the role of geologists

International Nuclear Information System (INIS)

Dutcher, L.A.F.; Dutcher, R.R.

1991-01-01

The United States has demonstrated reserves (coal potentially minable with current technology) sufficient to meet demand for at least 300 yrs (Illinois Coal Association, 1990, p. 5) at the 1990 production rate of 930,900,000 tonnes (1,024,000,000 tons) (Energy Information Administration, 1991, p. 6). These deposits, underlying about 13% of the country's land area, are the energy equivalent of about 2,000,000,000,000 bbl of crude oil - more than triple the world's known oil reserves. About 85% of coal used in the nation goes to the electric utility industry to generate 55% of the electricity produced in the US. The remaining buyers include steel, other industrial facilities, and retail dealers to a limited extent. Future increases in demand will depend upon economic growth of domestic and foreign markets and the price of competing fuels. However, future demand especially will depend upon the scope of government regulation and the progress of research and technology development in reducing environmental impacts resulting from mining and utilization and in advancing clean coal-burning technologies

Computational fluid dynamic simulations of coal-fired utility boilers: An engineering tool

Energy Technology Data Exchange (ETDEWEB)

Efim Korytnyi; Roman Saveliev; Miron Perelman; Boris Chudnovsky; Ezra Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

2009-01-15

The objective of this study was to develop an engineering tool by which the combustion behavior of coals in coal-fired utility boilers can be predicted. We presented in this paper that computational fluid dynamic (CFD) codes can successfully predict performance of - and emission from - full-scale pulverized-coal utility boilers of various types, provided that the model parameters required for the simulation are properly chosen and validated. For that purpose we developed a methodology combining measurements in a 50 kW pilot-scale test facility with CFD simulations using the same CFD code configured for both test and full-scale furnaces. In this method model parameters of the coal processes are extracted and validated. This paper presents the importance of the validation of the model parameters which are used in CFD codes. Our results show very good fit of CFD simulations with various parameters measured in a test furnace and several types of utility boilers. The results of this study demonstrate the viability of the present methodology as an effective tool for optimization coal burning in full-scale utility boilers. 41 refs., 9 figs., 3 tabs.

The effects of coal quality on NO{sub x} emissions and carbon burnout in pulverised coal-fired utility boilers

Energy Technology Data Exchange (ETDEWEB)

O`Connor, M. [National Power plc, Swindon (United Kingdom)

1999-04-01

A comprehensive study is reported on the impact of coal quality on nitrogen oxides emissions and carbon burnout in utility boilers, with the aim of assessing their relationship and developing predictive tools for assessing coals. Experimental work was carried out on various laboratory-scale apparatus and on single burner test facilities ranging from 160 kW{sub th} to 40 MW{sub th} in size and measurements were obtained from full-scale 500 MW{sub e} utility boiler trials. This data and basic coal data were then used to develop mathematical models to predict full-scale boiler performance with respect to NO{sub x} emissions and carbon burnout. Power station trials demonstrated that coal quality effects nitrogen oxides and burnout. The variability in boiler conditions also impacted on these factors. Lower nitrogen and higher volatile coals generally produced less NO{sub x}. Volatile content was the most important generic coal property for predicting burnout. Modelling rig tests, using data from advanced laboratory-scale tests, were found to be just as successful as using rig tests for predicting NO{sub x} performance of different coals. Laboratory-scale tests were found to be successful in providing accurate predictions of burnout for the coals studied. Mathematical models, however, were found to be less successful in this area and further work to develop this is required. A major achievement was CFD solutions of full-scale utility boiler furnaces in a single mesh. 32 refs., 15 figs., 33 tabs., 2 apps.

30 CFR 817.87 - Coal mine waste: Burning and burned waste utilization.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-UNDERGROUND MINING ACTIVITIES § 817.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or unburned coal mine waste shall be removed from a permitted disposal...

30 CFR 816.87 - Coal mine waste: Burning and burned waste utilization.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal mine waste: Burning and burned waste...-SURFACE MINING ACTIVITIES § 816.87 Coal mine waste: Burning and burned waste utilization. (a) Coal mine... extinguishing operations. (b) No burning or burned coal mine waste shall be removed from a permitted disposal...

Synergistic Effect of Co-utilization of Coal and Biomass Char: An Overview

Science.gov (United States)

Paiman, M. E. S.; Hamzah, N. S.; Idris, S. S.; Rahman, N. A.; Ismail, K.

2018-05-01

Global concerns on impact of greenhouse gases emission, mostly released from coal-fired power plant, and the depletion of fossil fuel particularly coal, has led the production of electricity from alternatives resources such as co-utilization technologies. Previous studies proved that the co-utilization of coal and biomass/biomass chars has significantly reduced the emission of greenhouse gases either during the pyrolysis, combustion or gasification process in laboratories, pilots as well as in the industrial scales. Interestingly, most of the studies reported the presence of synergistic effect during the co-utilization processes particularly between coal and biomass char while some are not. Biomass chars were found to have porous and highly disorder carbon structure and belong to the class of most reactive carbon material, resulting to be more reactive than those hard coal and lignite. Up to date, microwave assisted pyrolysis is one of the best and latest techniques employed to produce better quality of biomass chars and it is also reduce the processing cost. Lot of works has been done regarding on the existence of synergistic effects during its co-utilization. However, the knowledge is limited to thermal and product characteristics so far. Even so, the specific reasons behind its existence are yet to understand well. Therefore, in this paper, the emphasis will be given on the synergistic effects on emission characteristics of co-utilization of coal and biomass chars so that it can be apply in energy-based industries to help in reduction of the greenhouse gases emission.

Low-rank coal research

Energy Technology Data Exchange (ETDEWEB)

Weber, G. F.; Laudal, D. L.

1989-01-01

This work is a compilation of reports on ongoing research at the University of North Dakota. Topics include: Control Technology and Coal Preparation Research (SO{sub x}/NO{sub x} control, waste management), Advanced Research and Technology Development (turbine combustion phenomena, combustion inorganic transformation, coal/char reactivity, liquefaction reactivity of low-rank coals, gasification ash and slag characterization, fine particulate emissions), Combustion Research (fluidized bed combustion, beneficiation of low-rank coals, combustion characterization of low-rank coal fuels, diesel utilization of low-rank coals), Liquefaction Research (low-rank coal direct liquefaction), and Gasification Research (hydrogen production from low-rank coals, advanced wastewater treatment, mild gasification, color and residual COD removal from Synfuel wastewaters, Great Plains Gasification Plant, gasifier optimization).

Preparation and evaluation of coal-derived activated carbons for removal of mercury vapor from simulated coal combustion flue fases

Science.gov (United States)

Hsi, H.-C.; Chen, S.; Rostam-Abadi, M.; Rood, M.J.; Richardson, C.F.; Carey, T.R.; Chang, R.

1998-01-01

Coal-derived activated carbons (CDACs) were tested for their suitability in removing trace amounts of vapor-phase mercury from simulated flue gases generated by coal combustion. CDACs were prepared in bench-scale and pilot-scale fluidized-bed reactors with a three-step process, including coal preoxidation, carbonization, and then steam activation. CDACs from high-organicsulfur Illinois coals had a greater equilibrium Hg0 adsorption capacity than activated carbons prepared from a low-organic-sulfur Illinois coal. When a low-organic-sulfur CDAC was impregnated with elemental sulfur at 600 ??C, its equilibrium Hg0 adsorption capacity was comparable to the adsorption capacity of the activated carbon prepared from the high-organicsulfur coal. X-ray diffraction and sulfur K-edge X-ray absorption near-edge structure examinations showed that the sulfur in the CDACs was mainly in organic forms. These results suggested that a portion of the inherent organic sulfur in the starting coal, which remained in the CDACs, played an important role in adsorption of Hg0. Besides organic sulfur, the BET surface area and micropore area of the CDACs also influenced Hg0 adsorption capacity. The HgCl2 adsorption capacity was not as dependent on the surface area and concentration of sulfur in the CDACs as was adsorption of Hg0. The properties and mercury adsorption capacities of the CDACs were compared with those obtained for commercial Darco FGD carbon.

Survey report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Dispatch of engineers; 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (senmonka haken)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The purpose of this survey is to improve the coal utilization technology and to contribute to the environmental protection. Through long-term dispatch of experts for the coal utilization technology, coal utilization facilities are surveyed at the sites, advises for coal utilization technology and environmental protection technology are given, and useful information for the cooperation with the partner country are exchanged. In this fiscal year, experts were dispatched to Thailand in addition to China, to conduct cooperative surveys, technical exchanges and seminars with both countries. Experts for desulfurization technology, circulating fluidized bed boilers, effective coal ash utilization technology, and coal preparation technology were dispatched to various places in China. Among various model projects conducted in China, examples of model projects for simplified desulfurizer introduction, circulating fluidized bed boiler introduction, and briquette production facility introduction were presented at seminars held at two cities in China. Experts for briquette production technology and circulating fluidized bed boiler technology were dispatched to Thailand, to conduct cooperative surveys and technical exchanges. 22 figs., 9 tabs.

Fiscal 1995 survey report on the environmentally friendly type coal utilization system joint demonstration project. Water-saving coal preparation system joint demonstration project; Kankyo chowagata sekitan riyo system kyodo jissho jigyo. Shosuigata sentan system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This project makes demonstration of clean coal technology (CCT) in China and preparation for the base of its spread, controlled environmental pollution due to the coal use by the countries concerned, and contributes to stably secure energy of Japan. The paper made analog operation in the 1960s-1970s, supported by Russia and Poland, introduced two computer systems for operational control and quality control, densimeter, level meter, flow meter and analyzer to coal preparation plants having problems on productivity and quality control, made the optimum operational diagnosis for the plants, and at the same time, demonstrated the comprehensive rehabilitation type system by which water saving, high quality and high effectiveness are obtained. Various types of sensors such as rapid ash meter, scale and densitometer and computers are introduced to coal preparation plants which were recently constructed in China, have jig or heavy liquid cyclone as main preparation equipment and conducts operational control. There, the central control system was demonstrated in which various information collected in the central operation room and in-site equipment is combined by network for high-grade data processing and water saving is achieved. 50 figs., 11 tabs.

Proceedings of the international symposium on coal - science, technology, industry, business, environment

Energy Technology Data Exchange (ETDEWEB)

Narasimhan, K.S.; Sen, S. [eds.

1996-12-31

Papers were presented which covered the areas of coal science, advanced coal preparation, coal utilization, coal chemicals and the environment. These included carbon aromaticity, mineral studies, utilization of low rank coals, bioconversion of methane, swelling of coals, photocatalytic activity, flotation and effects of oxidation, microbial desulfurization, deashing, briquetting, commercial scale conversion of coal to fuels and chemicals, role of coal in iron and steel making, coal-water mixtures, dyes and chemical products, nitrogen oxides emissions and pollution control. 45 papers have been abstracted separately for the IEA Coal Research CD-ROM.

Study for recovery and utilization of coal mine gas in Russia (Kuznetsk coal basin)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of reducing greenhouse effect gas emissions in line with the Joint Implementation, a study was conducted on recovery/utilization of methane gas emitted from the Chertinskaya coal mine in the Kuznetsk coal basin area. According to the survey, the methane gas emitted from the Chertinskaya coal mine into the atmospheric air is 26 million to 36 million tons on the levels of the annual coal production between 0.7 million and 1 million tons. However, the monthly gas recovery amount and concentration largely fluctuate, and therefore, the use method to cope with this was studied. The study was now under way, and the electric power production using gas engine was regarded as the best. In this project, only the Chertinskaya mine can generate power of 34,721 MWh. In the whole Kuznetsk coal basin, approximately 200 million m{sup 3} of gas is needed to be removed for safety of the mine. The use of this will probably bring energy substitution of about 128,000 tons/year and CO2 reduction of 2.8 million tons/year. (NEDO)

Ninth annual international Pittsburgh coal conference - proceedings

International Nuclear Information System (INIS)

Anon.

1992-01-01

Over 200 papers are presented under the following headings: coal preparation; Clean Coal Technology Program status; pre- and post-utilization processing; advanced conversion technologies; integrated gasification combined cycle; indirect liquefaction; advanced liquefaction process development; conversion processes; coal - from a user's perspective; issues associated with coal use in heat engines; fundamentals of combustion; advanced combustion systems; low quality fuel applications/fluidised beds; combustion systems; ash and sludge disposal/utilization; developing SO 2 /NO x control technologies; technical overview of air toxics; scientific, economic and policy perspectives on global climate change; Clean Air Act compliance strategies; environmental policy/technology; spontaneous combustion; and special topics

Quality control of repair of equipment for coal preparation plants. Upravlenie kachestvom remonta oborudovaniya ugleobogatitel'nykh fabrik

Energy Technology Data Exchange (ETDEWEB)

Okonishnikov, A I; Neskoromnykh, V M; Surzhenko, V S; Sirichenko, R P; Pavlyuchenko, S G; Lesikov, A V

1984-01-01

The Ukrniiugleobogashchenie, Kalininsk and Sukhodol'sk coal preparation plants have developed the SUKRO system for control of repair quality of coal preparation equipment in the USSR. The system is based on a system of standards used in coal preparation plants. The following systems of standards used by the SUKRO system are analyzed: organization standards (order of repair in a coal preparation plant, repair planning, spare part systems, methods for determining equipment wear, analysis of equipment failures), standards for maintenance and repair (methods for equipment maintenance, service life of each equipment component or system, structure of preventive repair or repair, organizational models of repair operations, lubrication systems), standards for assessment of labor quality during repair operations. Use of the SUKRO system in the Sukhodol'sk coal preparation plant is evaluated. The SUKRO forms a system of standards for repair and maintenance of equipment considering operation conditions in coal preparation plants, requirements for equipment reliability and service life. (4 refs.)

NOX EMISSION CONTROL OPTIONS FOR COAL-FIRED ELECTRIC UTILITY BOILERS

Science.gov (United States)

The paper reviews NOx control options for coal-fired electric utility boilers. (NOTE: Acid Rain NOx regulations, the Ozone Transport Commission's NOx Budget Program, revision of the New Source Performance Standards (NSPS) for NOx emissions from utility sources, and Ozone Transpor...

Coal utilization in the twenty-first century: How much and for how long?

International Nuclear Information System (INIS)

Gluskoter, H.

1993-01-01

It is projected that coal usage in the US will increase at approximately the historic rate as electricity consumption increases. Because the life expectancy of powerplants and coal mines is in the tens of years, the electricity to be produced from coal in 2001 will be generated in plants currently on line or under construction, and almost all of the coal consumed will come from existing mines. Coal produces two-thirds of the world's electricity and, on a worldwide basis, will continue to be a major source of energy for the remainder of this century and for some time to come. It is the longer term projections of coal utilization, beyond the next few decades, that remain much more difficult to predict. Fossil fuels are present in the Earth in finite amounts and are not renewable on the human scale of existence. Therefore, a shift to other sources of energy must occur eventually. A doubling of population will create a demand for greatly increased energy production. Historically, a 1% increase in world domestic product has been accompanied by a 1% increase in energy consumption. In most regions of the world, coal could supply a major portion of the increased energy and could do so without requiring major technological advances in coal mining and coal utilization technologies. The large, extensive, and accessible resources of coal, the ability to utilize it, and the demand pressures from an expanding population all bode well for the future of coal. However, there are also factors that may contribute to limiting the future use of coal. They include environmental concerns (acid rain, air toxics, and global warming) and the rate at which nonfossil-fuel sources (perhaps solar and nuclear) are developed. Although many of the decisions that will influence the future use of coal will be based on economic and environmental considerations, it is more than likely that politics will also play an important role in all of those decisions

Basic study for promoting joint implementation and others. Feasibility study on the recovery and utilization of coal mine methane of an Upper Silesian Coal Field

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Having the Mining Industry Restructuring Public Corporation located in the city of Katowice, Poland as the counterpart, a feasibility study has been executed on a project to utilize coal bed gas for power generation. Selected for the study are the 'Budryk coal mine' owned by KWK 'Budryk' Coal Company and the 'Pniowek coal mine' owned by Jastrzebie Coal Company. Since the Pniowek coal mine can utilize the whole quantity of recovered methane by 2001, the Budryk coal mine was selected as the object of the project. As a result of the trial calculation on the economy when the new gas power plant is installed in the Budryk coal mine, the energy substitution effect was found to equal to a power amount at transmission terminal of 6 MWh/year. Furthermore, when proliferation effect is taken into consideration, an enormous effect can be expected if new coal mines are developed and the existing cola mines will go further deeper, because the Silesian coal mine presently has the coal resource quantity of 57 billion tons and the annual gas discharge quantity of 750 million m{sup 3}. Therefore, if the technologies to recover, manage and utilize the gas are established at the Budryk coal mine, a large effect leading to an aspiration would be expected under the current situation of the structural reorganization under which the Polish coal companies are placed. (NEDO)

Improving occupational conditions in coal preparation plants considering noise factor. [USSR

Energy Technology Data Exchange (ETDEWEB)

Zhurbinskii, L.F.; Shabel' nikova, E.V.; Sidorov, E.G.

1985-11-01

Three research institutes (IOTT, UkrNIIugleobogashchenie and KuzNIIugleobogashchenie) investigated health hazards associated with noise in coal preparation plants in the Donbass, Kuzbass and Karaganda basins. Investigations showed that there is a close correlation of noise pollution with rate of illness (heart diseases, nervous system diseases, alimentary duct diseases, respiratory diseases and diseases of the auditory organs). An equation which describes the correlation is derived. Correlation coefficient (ranging from 0.75 to 0.94) for each of 4 types of diseases was determined. Analyses showed that reducing noise level from 95 to 85 dB caused a decrease in rate of illness ranging from 2.5 to 3.0 times. Absenteeism due to illness decreased 1.5 to 2.0 times. Investigations also showed that accident rate is influenced by noise level. About 30% of accidents fell on working places with increased noise level. About 10% of accidents fell on working places with noise level of about 85 dB and from 3 to 4% accidents on working places with noise level of about 70 dB. Methods for noise pollution control in coal preparation plants in the USSR are evaluated. Effects of coal transport and handling on noise pollution in coal preparation plants are analyzed.

Characterization of Rare Earth Element Minerals in Coal Utilization Byproducts

Energy Technology Data Exchange (ETDEWEB)

Montross, Scott N. [Oak Ridge Inst. for Science and Education (ORISE), Oak Ridge, TN (United States); Verba, Circe A. [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center; Collins, Keith [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center

2017-07-17

The United States currently produces over 100 million tons of coal utilization byproducts (CUB) per year in the form of fly ash, bottom ash, slag, and flue gas (American Coal Ash Association (ACCA), 2015). But this “waste material” also contains potentially useful levels of rare earth elements (REE). Rare earth elements are crucial for many existing and emerging technologies, but the U.S. lacks a domestic, sustainable REE source. Our project explored the possibility of developing a supply of REEs for U.S. technologies by extracting REEs from CUBs. This work offers the potential to reduce our dependence on other countries for supply of these critical elements (NETL, REE 2016 Project Portfolio). Geologic and diagenetic history, industrial preparation methods, and the specific combustion process all play major roles in the composition of CUB. During combustion, inorganic mineral phases of coal particles are fluidized at temperatures higher than 1400oC, so inorganic mineral materials are oxidized, fused, disintegrated, or agglomerated into larger spherical and amorphous (non-crystalline) particles. The original mineralogy of the coal-containing rock and heating/cooling of the material significantly affects the composition and morphology of the particles in the combustion byproduct (Kutchko and Kim, 2006). Thus, different types of coal/refuse/ash must be characterized to better understand mineral evolution during the combustion process. Our research focused on developing a working model to address how REE minerals behave during the combustion process: this research should help determine the most effective engineering methods for extracting REEs from CUBs. We used multimodal imaging and image processing techniques to characterize six rock and ash samples from different coal power plants with respect to morphology, grain size, presence of mineral phases, and elemental composition. The results of these characterization activities provided thresholds for realizing the

Materials for coal conversion and utilization

Energy Technology Data Exchange (ETDEWEB)

None,

1981-01-01

The Sixth annual conference on materials for coal conversion and utilization was held October 13-15, 1981 at the National Bureau of Standards Gaithersburg, Maryland. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the Gas Research Institute and the National Bureau of Standards. Fifty-eight papers from the proceedings have been entered individually into EDB and ERA; four papers had been entered previously from other sources. (LTN)

Enrichment of reactive macerals in coal: its characterization and utilization in coke making

Science.gov (United States)

Nag, Debjani; Kopparthi, P.; Dash, P. S.; Saxena, V. K.; Chandra, S.

2018-01-01

Macerals in coal are of different types: reactive and inert. These macerals are differ in their physical and chemical properties. Column flotation method has been used to separate the reactive macerals in a non-coking coal. The enriched coal is then characterized in order to understand the changes in the coking potential by different techniques. It is then used in making of metallurgical coke by proper blending with other coals. Enriched coal enhance the properties of metallurgical coke. This shows a path of utilization of non-coking coal in metallurgical coke making.

Basic studies on coal liquefaction reaction, reforming and utilization of liquefaction products

Energy Technology Data Exchange (ETDEWEB)

Shiraishi, M. (National Institute for Resources and Environment, Tsukuba (Japan))

1993-09-01

This report describes the achievement of research and development of coal liquefaction technologies in the Sunshine Project for FY 1992, regarding the coal liquefaction reaction, reforming and utilization of liquefaction products. For the fundamental study on coal liquefaction reaction, were investigated effect of asphaltene in petroleum residue on coprocessing, pretreatment effect in coprocessing of Taiheiyo coal and tarsand bitumen using oil soluble catalyst, solubilization and liquefaction of Taiheiyo coal at mild conditions with the aid of super acid, and flash hydropyrolysis of finely pulverized swollen coal under high hydrogen pressure. On the other hand, for the study on hydrotreatment of coal derived liquid, were investigated catalytic hydroprocessing of Wandoan coal liquids, production of gasoline from coal liquids by fluid catalytic cracking, solvent extraction of phenolic compounds from coal liquids, and separation of hetero compounds in coal liquid by means of high pressure crystallization. Further progress in these studies has been confirmed. 9 figs., 6 tabs.

Basic study for promoting joint implementation and others. Feasibility study on the recovery and utilization of coal mine methane of an Upper Silesian Coal Field

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Having the Mining Industry Restructuring Public Corporation located in the city of Katowice, Poland as the counterpart, a feasibility study has been executed on a project to utilize coal bed gas for power generation. Selected for the study are the 'Budryk coal mine' owned by KWK 'Budryk' Coal Company and the 'Pniowek coal mine' owned by Jastrzebie Coal Company. Since the Pniowek coal mine can utilize the whole quantity of recovered methane by 2001, the Budryk coal mine was selected as the object of the project. As a result of the trial calculation on the economy when the new gas power plant is installed in the Budryk coal mine, the energy substitution effect was found to equal to a power amount at transmission terminal of 6 MWh/year. Furthermore, when proliferation effect is taken into consideration, an enormous effect can be expected if new coal mines are developed and the existing cola mines will go further deeper, because the Silesian coal mine presently has the coal resource quantity of 57 billion tons and the annual gas discharge quantity of 750 million m{sup 3}. Therefore, if the technologies to recover, manage and utilize the gas are established at the Budryk coal mine, a large effect leading to an aspiration would be expected under the current situation of the structural reorganization under which the Polish coal companies are placed. (NEDO)

National coal utilization assessment. An integrated assessment of increased coal use in the Midwest: impacts and constraints

Energy Technology Data Exchange (ETDEWEB)

Hoover, L. John

1977-10-01

This study was performed as a part of the Argonne National Laboratory Regional Studies program, which is sponsored by the Department of Energy. The purpose is to assess the impacts and consequences associated with alternative energy options on a regional basis, and to identify and analyze alternative mitigation and solution strategies for increasing the acceptability of these options. The National Coal Utilization Assessment is being conducted as a part of the Regional Studies Program. This particular study is focusing on impacts and constraints on increased coal utilization. In addition, a major focal point for the study is the identification and analysis of alternative solution strategies applicable to these constraints and problems.

Coal blending preparation for non-carbonized coal briquettes

Science.gov (United States)

Widodo; Fatimah, D.; Estiaty, L. M.

2018-02-01

Referring to the national energy policy targets for the years 2025, the government has launched the use of coal briquettes as an alternative energy replacement for kerosene and firewood. Non-carbonized briquettes in the form of coal briquettes as well as bio-coal briquettes are used in many small-medium industries and households, and are rarely used by large industries. The standard quality of coal briquettes used as raw material for non-carbonized briquettes is a minimum calorific value of 4,400 kcal/kg (adb); total sulfur at a maximum of 1% (adb), and water content at plants), the environment of deposition, and the geological conditions of the surrounding area, so that the coal deposits in each region will be different as well as the amount and also the quality. Therefore, the quantity and the quality of coal in each area are different to be eligible in the making of briquettes to do blending. In addition to the coal blending, it is also necessary to select the right materials in the making of coal briquettes and bio-coal briquettes. The formulation of the right mixture of material in the making of briquettes, can be produced of good quality and environmental friendly.

Clean utilization of low-rank coals for low-cost power generation

International Nuclear Information System (INIS)

Sondreal, E.A.

1992-01-01

Despite the unique utilization problems of low-rank coals, the ten US steam electric plants having the lowest operating cost in 1990 were all fueled on either lignite or subbituminous coal. Ash deposition problems, which have been a major barrier to sustaining high load on US boilers burning high-sodium low-rank coals, have been substantially reduced by improvements in coal selection, boiler design, on-line cleaning, operating conditions, and additives. Advantages of low-rank coals in advanced systems are their noncaking behavior when heated, their high reactivity allowing more complete reaction at lower temperatures, and the low sulfur content of selected deposits. The principal barrier issues are the high-temperature behavior of ash and volatile alkali derived from the coal-bound sodium found in some low-rank coals. Successful upgrading of low-rank coals requires that the product be both stable and suitable for end use in conventional and advanced systems. Coal-water fuel produced by hydrothermal processing of high-moisture low-rank coal meets these criteria, whereas most dry products from drying or carbonizing in hot gas tend to create dust and spontaneous ignition problems unless coated, agglomerated, briquetted, or afforded special handling

Enzymatic desulfurization of coal

Energy Technology Data Exchange (ETDEWEB)

Boyer, Y.N.; Crooker, S.C.; Kitchell, J.P.; Nochur, S.V.

1991-05-16

The overall objective of this program was to investigate the feasibility of an enzymatic desulfurization process specifically intended for organic sulfur removal from coal. Toward that end, a series of specific objectives were defined: (1) establish the feasibility of (bio)oxidative pretreatment followed by biochemical sulfate cleavage for representative sulfur-containing model compounds and coals using commercially-available enzymes; (2) investigate the potential for the isolation and selective use of enzyme preparations from coal-utilizing microbial systems for desulfurization of sulfur-containing model compounds and coals; and (3) develop a conceptual design and economic analysis of a process for enzymatic removal of organic sulfur from coal. Within the scope of this program, it was proposed to carry out a portion of each of these efforts concurrently. (VC)

Preparation and Stability of Inorganic Solidified Foam for Preventing Coal Fires

Directory of Open Access Journals (Sweden)

Botao Qin

2014-01-01

Full Text Available Inorganic solidified foam (ISF is a novel material for preventing coal fires. This paper presents the preparation process and working principle of main installations. Besides, aqueous foam with expansion ratio of 28 and 30 min drainage rate of 13% was prepared. Stability of foam fluid was studied in terms of stability coefficient, by varying water-slurry ratio, fly ash replacement ratio of cement, and aqueous foam volume alternatively. Light microscope was utilized to analyze the dynamic change of bubble wall of foam fluid and stability principle was proposed. In order to further enhance the stability of ISF, different dosage of calcium fluoroaluminate was added to ISF specimens whose stability coefficient was tested and change of hydration products was detected by scanning electron microscope (SEM. The outcomes indicated that calcium fluoroaluminate could enhance the stability coefficient of ISF and compact hydration products formed in cell wall of ISF; naturally, the stability principle of ISF was proved right. Based on above-mentioned experimental contents, ISF with stability coefficient of 95% and foam expansion ratio of 5 was prepared, which could sufficiently satisfy field process requirements on plugging air leakage and thermal insulation.

Numerical investigation of influence thermal preparation coal on nitric oxides formation in combustion process

Energy Technology Data Exchange (ETDEWEB)

Chernetskaya, N. [Siberian Federal Univ., Krasnoyarsk (Russian Federation); Chernetsky, M.; Dekterev, A. [Siberian Federal Univ., Krasnoyarsk (Russian Federation); Kutateladze Institute of Thermophysics, Novosibirsk (Russian Federation)

2013-07-01

Emissions of nitrogen oxides from coal combustion are a major environmental problem because they have been shown to contribute to the formation of acid rain and photochemical smog. Coal thermalpreparation before furnace delivery is effective method to reduce NOx emissions, shown by experiments in small-scale facilities (Babiy VI, Alaverdov PI, Influence of thermal preparation pulverized coal on nitric oxides outlet for combustion different metamorphized coal. ATI, 1983). This paper presents the mathematical model of burning thermal preparation coal. Validation of the model was carried out on laboratory-scale plant of All-Russia thermal engineering institute. Modeling of low-emissive burner with preliminary heating coal dust is made for the purpose of search of burner optimal constructions which provides low concentration of nitric oxides in the boiler. For modeling are used in-house CFD code ''{sigma}Flow'' (Dekterev AA, Gavrilov AA, Harlamov EB, Litvintcev KY, J Comput Technol 8(Part 1):250-255, 2003).

Development of processes for the utilization of Brazilian coal using nuclear process heat and/or nuclear process steam

International Nuclear Information System (INIS)

Bamert, H.; Niessen, H.F.; Walbeck, M.; Wasrzik, U.; Mueller, R.; Schiffers, U.; Strauss, W.

1980-01-01

Status of the project: End of the project definition phase and preparation of the planned conceptual phase. Objective of the project: Development of processes for the utilization of nuclear process heat and/or nuclear process steam for the gasification of coal with high ash content, in particular coal from Brazil. Results: With the data of Brazilian coal of high ash content (mine Leao/ 43% ash in the mine-mouth quality, 20% ash after preparation) there have been worked out proposals for the mine planning and for a number of processes. On the basis of these proposals and under consideration of the main data specified by the Brazilian working group there have been choosen two processes and worked out in a conceptual design: 1) pressurized water reactor + LURGI-pressure gasifier/hydrogasification for the production of SNG and 2) high temperature reactor steam gasification for the production of town gas. The economic evaluation showed that the two processes are not substantially different in their cost efficiency and they are economical on a long-term basis. For more specific design work there has been planned the implementation of an experimental programme using the semi-technical plants 'hydrogasification' in Wesseling and 'steam gasification' in Essen as the conceptual phase. (orig.) [de

Coal Preparation and Processing Plants New Source Performance Standards (NSPS)

Science.gov (United States)

Learn about the NSPS regulation for coal preparation and processing plants by reading the rule summary, the rule history, the code of federal regulation text, the federal register, and additional docket documents

Microporous Organic Polymers Based on Hyper-Crosslinked Coal Tar: Preparation and Application for Gas Adsorption.

Science.gov (United States)

Gao, Hui; Ding, Lei; Bai, Hua; Li, Lei

2017-02-08

Hyper-crosslinked polymers (HCPs) are promising materials for gas capture and storage, but high cost and complicated preparation limit their practical application. In this paper, a new type of HCPs (CTHPs) was synthesized through a one-step mild Friedel-Crafts reaction with low-cost coal tar as the starting material. Chloroform was utilized as both solvent and crosslinker to generate a three-dimensional crosslinked network with abundant micropores. The maximum BET surface area of the prepared CTHPs could reach up to 929 m 2  g -1 . Owing to the high affinity between the heteroatoms on the coal-tar building blocks and the CO 2 molecules, the adsorption capacity of CTHPs towards CO 2 reached up to 14.2 wt % (1.0 bar, 273 K) with a high selectivity (CO 2 /N 2 =32.3). Furthermore, the obtained CTHPs could adsorb 1.27 wt % H 2 at 1.0 bar and 77.3 K, and also showed capacity for the capture of high organic vapors at room temperature. In comparison with other reported porous organic polymers, CTHPs have the advantages of low-cost, easy preparation, and high gas-adsorption performance, making them suitable for mass production and practical use in the future. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in Malaysia and Vietnam; Kankyo chowagata sekitan riyo system kanosei chosa. Malaysia Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

This survey arranged the status of coal utilization technology and the status of coal production, supply, etc. in Malaysia and Vietnam, examined/studied coal utilization systems in both countries, and finally assessed feasibility of introducing the environmentally friendly type coal utilization system. As a country of primary energy source which is abundant in crude oil, natural gas, hydroelectric power, coal, etc., Malaysia now depends on crude oil and natural gas for 80% of its energy, and places emphasis on exploration of natural gas and oil refining. In electric power and cement industries where coal is consumed, effectiveness and environmental issues in association with coal utilization are future subjects. In Vietnam, the north is abundant in hydroelectric power and anthracite, and the south in oil and gas resource, but the north and central districts are in a state of undevelopment. Coal is used for coal thermal power generation, cement industry, and residential/commercial fuel. In the future, effective coal utilization and environmental issues will be subjects. 16 refs., 38 figs., 75 tabs.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Feasibility study of the environmentally friendly type coal utilization system in the Philippines; Kankyo chowagata sekitan riyo system kanosei chosa. Philippines ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Grasping the present situation of coal utilization technology in the Philippines, the paper proposed a feasibility study of introduction of the environmentally friendly type coal utilization system which seems to be needed in the future. (1) Introduction of the environmentally friendly type coal utilization system in the electric power generation sector: there are only four full-scale running coal thermal power plants in the Philippines. In the future, several coal thermal plants are planned to be constructed by 2005, but for the new installation, it is desirable to adopt fluidized bed boilers with wide application to coal kinds. In case of 0.3-1.0 million MW class plants, it is planned to adopt high grade import coals, and it will be natural to fire pulverized coal. For the processing of flue gas, it is a must to install desulfurization facilities and smoke/soot removal devices. (2) Utilization/development of domestic low grade coals: at the mine-mouth generating plant, it is necessary to investigate the economically minable amount of coal, confirm productivity, survey coal quality, etc., and select boiler. As to coal briquetting technology, it is necessary to examine coal quality for tests and make a thorough study of what technology is most suitable. 50 figs., 78 tabs.

Intelligent control and maintenance of management integrated system based on multi-agents for coal preparation plant

Energy Technology Data Exchange (ETDEWEB)

Meng, F.; Wang, Y. [China University of Mining and technology, Xuzhou (China). School of Information and Electrical Engineering

2006-06-15

This paper discusses the progress of computer integrated processing (CIPS) of coal preparation and then presents an intelligence controlled production process, device-maintenance and production-management system of coal preparation based on multi-agents (IICMMS-CP). The construction of the IICMMS-CP, the distributed network control system based on live intelligence control stations and the strategy of implementing a distributed intelligence control system are studied in order to overcome the disadvantages brought about by the wide use of the PLC system by coal preparation plants. The software frame, based on a Multi-Agent Intelligence Control and Maintenance Management integrated system, is studied and the implementation methods of IICMMS-CP are discussed. The characteristics of distributed architecture, cooperation and parallel computing meet the needs of integrated control of coal preparation plants with large-scale spatial production distribution, densely-related processes and complex systems. Its application further improves the reliability and precision of process control, accuracy of fault identification and intelligence of production adjustment, establishes a technical basis for system integration and flexible production. The main function of the system has been tested in a coal preparation plant to good effect in stabilizing product quality, improving efficiency and reducing consumption. 17 refs., 4 figs.

Current status of U.S. coal utilization and non-fuel uses of fossil fuels

International Nuclear Information System (INIS)

Song, C.S.; Schobert, H.; Scaroni, A.W.

1997-01-01

An understanding of the current situation is important for projecting the future direction of coal utilization. The world's annual consumption of coal in 1995 was 5104.01 million short tons (MST, 1 short ton = 0.907 metric ton). Coal plays a very important role in the US energy supply; US coal production in 1995 totaled 1033 MST, including 611.1 MST of bituminous coal, 328.4 MST of subbituminous coal, 86.1 MST of lignite, and 4.1 MST of anthracite. US coal consumption totaled 940.6 MST, with 88.1% in electric utilities, 3.5% in coke plants, 7.8% for other industrial uses, and only 0.6% in the residential and commercial sectors. The amount of fossil resources used for non-fuel purposes accounted for 8.4% of the total annual consumption in 1995. Non-fuel uses of fossil fuels particularly coal may become more important in the future. The demonstrated coal reserves in the world are large enough for consumption for over 220 years at the 1995 level, while proven oil reserves are only about 40 times the world's 1995 consumption level. Coal has several positive attributes when considered as a feedstock for aromatic chemicals, specialty chemicals, and carbon-based materials. Existing nonfuel uses of coals include (1) high temperature carbonization of bituminous and subbituminous coals to make metallurgical coke; (2) gasification of coal to make synthesis gases and other chemicals; (3) use of coal in manufacturing other materials such as activated carbons, carbon molecular sieves (CMS) and production of phosphorus (phosphoric acid); (4) the use of coal tars from carbonization and gasification for making aromatic and phenolic chemicals; (5) the use of coal tar pitch for making carbon fibers and activated carbon fibers; and (6) other non-fuel products derived from coal including combustion by-products. Coal may become more important both as an energy source and as the source of chemical feedstocks in the 21st century

CEZ utility's coal-fired power plants: towards a higher environmental friendliness

International Nuclear Information System (INIS)

Kindl, V.; Spilkova, T.; Vanousek, I.; Stehlik, J.

1996-01-01

Environmental efforts of the major Czech utility, CEZ a.s., are aimed at reducing air pollution arising from electricity and heat generating facilities. There are 3 main kinds of activity in this respect: phasing out of coal fired power plants; technological provisions to reduce emissions of particulate matter, sulfur dioxide, and nitrogen oxides from those coal fired units that are to remain in operation after 1998; and completion of the Temelin nuclear power plant. In 1995, emissions of particulate matter, sulfur dioxide, nitrogen oxides, and carbon monoxide from CEZ's coal fired power plants were 19%, 79%, 59%, and 60%, respectively, with respect to the situation in 1992. The break-down of electricity generation by CEZ facilities (in GWh) was as follows in 1995: hydroelectric power plants 1673, nuclear power plants 12230, coal fired power plants without desulfurization equipment 30181, and coal fired power plants with desulfurization equipment 2277. Provisions implemented to improve the environmental friendliness of the individual CEZ's coal fired power plants are described in detail. (P.A.). 5 tabs., 1 fig

Flash pyrolysis of coal-solvent slurry prepared from the oxidized coal and the coal dissolved in solvent; Ichibu yokaishita sanka kaishitsutan slurry no jinsoku netsubunkai

Energy Technology Data Exchange (ETDEWEB)

Maki, T.; Mae, K.; Okutsu, H.; Miura, K. [Kyushu University, Fukuoka (Japan). Faculty of Engineering

1996-10-28

In order to develop a high-efficiency coal pyrolysis method, flash pyrolysis was experimented on slurry prepared by using liquid-phase oxidation reformed coal and a methanol-based solvent mixture. Australian Morwell coal was used for the experiment. The oxidized coal, into which carboxyl groups have been introduced, has the condensation structure relaxed largely, and becomes highly fluid slurry by means of the solvent. Char production can be suppressed by making the oxidation-pretreated coal into slurry, resulting in drastically improved pyrolytic conversion. The slurry was divided into dissolved solution, dried substance, extracted residue, and residual slurry, which were pyrolized independently. The dissolved solution showed very high conversion. Improvement in the conversion is contributed by separating the dissolved substances (coal macromolecules) at molecular levels, coagulating the molecules, suppressing cross-link formation, and reducing molecular weight of the dissolved substances. Oxidized coal can be dissolved to 80% or higher by using several kinds of mixed solvents. As a result of the dissolution, a possibility was suggested on pyrolysis which is easy in handling and high in conversion. 7 refs., 6 figs., 2 tabs.

The Research of Utilization Hours of Coal-Fired Power Generation Units Based on Electric Energy Balance

Science.gov (United States)

Liu, Junhui; Yang, Jianlian; Wang, Jiangbo; Yang, Meng; Tian, Chunzheng; He, Xinhui

2018-01-01

With grid-connected scale of clean energy such as wind power and photovoltaic power expanding rapidly and cross-province transmission scale being bigger, utilization hours of coal-fired power generation units become lower and lower in the context of the current slowdown in electricity demand. This paper analyzes the influencing factors from the three aspects of demand, supply and supply and demand balance, and the mathematical model has been constructed based on the electric energy balance. The utilization hours of coal-fired power generation units have been solved considering the relationship among proportion of various types of power installed capacity, the output rate and utilization hours. By carrying out empirical research in Henan Province, the utilization hours of coal-fired units of Henan Province in 2020 has been achieved. The example validates the practicability and the rationality of the model, which can provide a basis for the decision-making for coal-fired power generation enterprises.

COAL-FIRED UTILITY BOILERS: SOLVING ASH DEPOSITION PROBLEMS; TOPICAL

International Nuclear Information System (INIS)

Christopher J. Zygarlicke; Donald P. McCollor; Steven A. Benson; Jay R. Gunderson

2001-01-01

The accumulation of slagging and fouling ash deposits in utility boilers has been a source of aggravation for coal-fired boiler operators for over a century. Many new developments in analytical, modeling, and combustion testing methods in the past 20 years have made it possible to identify root causes of ash deposition. A concise and comprehensive guidelines document has been assembled for solving ash deposition as related to coal-fired utility boilers. While this report accurately captures the current state of knowledge in ash deposition, note that substantial research and development is under way to more completely understand and mitigate slagging and fouling. Thus, while comprehensive, this document carries the title ''interim,'' with the idea that future work will provide additional insight. Primary target audiences include utility operators and engineers who face plant inefficiencies and significant operational and maintenance costs that are associated with ash deposition problems. Pulverized and cyclone-fired coal boilers are addressed specifically, although many of the diagnostics and solutions apply to other boiler types. Logic diagrams, ash deposit types, and boiler symptoms of ash deposition are used to aid the user in identifying an ash deposition problem, diagnosing and verifying root causes, determining remedial measures to alleviate or eliminate the problem, and then monitoring the situation to verify that the problem has been solved. In addition to a step-by-step method for identifying and remediating ash deposition problems, this guideline document (Appendix A) provides descriptions of analytical techniques for diagnostic testing and gives extensive fundamental and practical literature references and addresses of organizations that can provide help in alleviating ash deposition problems

Preparation and combustion of coal-water fuel from the Sin Pun coal deposit, southern Thailand

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-05-01

In response to an inquiry by the Department of Mineral Resources in Thailand, the Energy & Environmental Research Center (EERC) prepared a program to assess the responsiveness of Sin Pun lignite to the temperature and pressure conditions of hot-water drying. The results indicate that drying made several improvements in the coal, notably increases in heating value and carbon content and reductions in equilibrium moisture and oxygen content. The equilibrium moisture content decreased from 27 wt% for the raw coal to about 15 wt% for the hot-water-dried (HWD) coals. The energy density for a pumpable coal-water fuel (CWF) indicates an increase from 4500 to 6100 Btu/lb by hot-water drying. Approximately 650 lb of HWD Sin Pun CWF were fired in the EERC`s combustion test facility. The fuel burned extremely well, with no feed problems noted during the course of the test. Fouling and slagging deposits each indicated a very low rate of ash deposition, with only a dusty layer formed on the cooled metal surfaces. The combustor was operated at between 20% and 25% excess air, resulting in a flue gas SO{sub 2} concentration averaging approximately 6500 parts per million.

Numerical investigation of heat transfer characteristics in utility boilers of oxy-coal combustion

International Nuclear Information System (INIS)

Hu, Yukun; Li, Hailong; Yan, Jinyue

2014-01-01

Highlights: • Air-coal and oxy-coal combustion in an industrial scale PF boiler were simulated in ANSYS FLUENT. • The O 2 concentration of 33 vol% in the oxy-coal combustion case matches the air-coal combustion case most closely. • The moisture in the flue gas has little impact on flame temperature, but positive impact on surface incident radiation. - Abstract: Oxy-coal combustion has different flue gas composition from the conventional air-coal combustion. The different composition further results in different properties, such as the absorption coefficient, emissivity, and density, which can directly affect the heat transfer in both radiation and convection zones of utility boilers. This paper numerically studied a utility boiler of oxy-coal combustion and compares with air-coal combustion in terms of flame profile and heat transferred through boiler side walls in order to understand the effects of different operating conditions on oxy-coal boiler retrofitting and design. Based on the results, it was found that around 33 vol% of effective O 2 concentration ([O 2 ] effective ) the highest flame temperature and total heat transferred through boiler side walls in the oxy-coal combustion case match to those in the air-coal combustion case most; therefore, the 33 vol% of [O 2 ] effective could result in the minimal change for the oxy-coal combustion retrofitting of the existing boiler. In addition, the increase of the moisture content in the flue gas has little impact on the flame temperature, but results in a higher surface incident radiation on boiler side walls. The area of heat exchangers in the boiler was also investigated regarding retrofitting. If boiler operates under a higher [O 2 ] effective , to rebalance the load of each heat exchanger in the boiler, the feed water temperature after economizer can be reduced or part of superheating surfaces can be moved into the radiation zone to replace part of the evaporators

Utilization of brown coal in FRG power plants

Energy Technology Data Exchange (ETDEWEB)

Kotler, V.R.

1985-07-01

FRG methods are studied for utilizing brown coal in view of the development of Kansk-Achinsk brown coal deposits. The use of brown coal in FRG power plants has increased from 15% in 1950- 1960 to 85% (total output) in 1982, providing 79.4 TWh of electrical energy. The remainder was used for briquetting, pulverization and breeze coke. In 1982 nearly 100 million tons of brown coal were burned by six large power stations (rated capacity 11,400 MW) to produce nearly 80 billion kWh of energy. Measures are discussed taken to reduce slagging and to remove excessive moisture content. Problems are analyzed associated with increased contamination of the atmosphere in areas with high population density (412/km/sup 2/) and cost of suppression is reviewed. According to available data, the cost of preventive measures taken by FRG, USA, Japan and the Netherlands is equal to 30% of the total cost of the energy. The most critical problem is suppression of sulfur dioxide, either by dry or wet scrubbers or by the addition of dry dolomite or lime to the furnace (75% of all SO/sub 2/ emissions in FRG comes from power stations). A method is described developed by RWE based on a series of distribution headers in the upper part of combustion chambers. At best, 70-80% reduction can be achieved. 14 references.

The role of clean coal technologies in a deregulated rural utility market

Energy Technology Data Exchange (ETDEWEB)

Neal, J.W. [National Rural Electric Cooperative Association, Arlington, VA (United States)

1997-12-31

The nation`s rural electric cooperatives own a high proportion of coal-fired generation, in excess of 80 percent of their generating capacity. As the electric utility industry moves toward a competitive electricity market, the generation mix for electric cooperatives is expected to change. Distributed generation will likely serve more customer loads than is now the case, and that will lead to an increase in gas-fired generation capacity. But, clean low-cost central station coal-fired capacity is expected to continue to be the primary source of power for growing rural electric cooperatives. Gasification combined cycle could be the lowest cost coal based generation option in this new competitive market if both capital cost and electricity production costs can be further reduced. This paper presents anticipated utility business scenarios for the deregulated future and identifies combined cycle power plant configurations that might prove most competitive.

Fiscal 1997 survey of the overseas coal import base preparation/improvement. Survey of a coal flow in China; 1997 nendo kaigaitan yunyu kiban seibi sokushin chosa. Chugoku ni okeru coal flow ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The paper surveyed the preparation of the coal transportation infrastructure, status of its running, economical efficiency, etc. in terms mainly of the trend of coal production/consumption in China, and coal railroad/water transportation and electric power transportation by mine-mouth power generation. From the survey, the following conclusions were obtained. As to the coal which China uses as a main energy for maintaining the present high economic growth as targeted, there will remain the coal transportation problem between production site (north and west) and consumption site (east and south) still in the future (in 2000 and 2010). China is now facing with a big turning point in a socioeconomic aspect. The advancing opening market policy brought steep rises in energy prices such as coal and electric power, which is affecting various fields. Further, the energy related laws, which were unprepared, are abruptly being prepared, and the environment for the introduction of foreign investment, which is expected to be accelerated, is being prepared. In the future, attention should be paid to environmental problems such as air pollution, acid rain and global warming. 48 figs., 96 tabs.

MERCURY CONTROL IN MUNICIPAL WASTE COMBUSTORS AND COAL-FIRED UTILITIES

Science.gov (United States)

Control of mercury (Hg) emissions from municipal waste combustors (MWCs) and coal-fired utilities has attracted attention due to current and potential regulations. Among several techniques evaluated for Hg control, dry sorbent injection (primarily injection of activated carbon) h...

National Coal Quality Inventory (NACQI)

Energy Technology Data Exchange (ETDEWEB)

Robert Finkelman

2005-09-30

The U.S. Geological Survey (USGS) conducted the National Coal Quality Inventory (NaCQI) between 1999 and 2005 to address a need for quality information on coals that will be mined during the next 20-30 years. Collaboration between the USGS, State geological surveys, universities, coal burning utilities, and the coal mining industry plus funding support from the Electric Power Research Institute (EPRI) and the U.S. Department of Energy (DOE) permitted collection and submittal of coal samples for analysis. The chemical data (proximate and ultimate analyses; major, minor and trace element concentrations) for 729 samples of raw or prepared coal, coal associated shale, and coal combustion products (fly ash, hopper ash, bottom ash and gypsum) from nine coal producing States are included. In addition, the project identified a new coal reference analytical standard, to be designated CWE-1 (West Elk Mine, Gunnison County, Colorado) that is a high-volatile-B or high-volatile-A bituminous coal with low contents of ash yield and sulfur, and very low, but detectable contents of chlorine, mercury and other trace elements.

The clean coal technologies for lignitic coal power generation in Pakistan

International Nuclear Information System (INIS)

Mir, S.; Raza, Z.; Aziz-ur-Rehman, A.

1995-01-01

Pakistan contains huge reserves of lignitic coals. These are high sulphur, high ash coals. In spite of this unfortunate situation, the heavy demand for energy production, requires the development utilization of these indigenous coal reserves to enhance energy production. The central of the environmental pollution caused by the combustion of these coals has been a major hindrance in their utilization. Recently a substantial reduction in coal combustion emissions have been achieved through the development of clean coal technologies. Pakistan through the transfer and adaptation of the advanced clean coal technologies can utilize incurring the high sulphur coals for energy production without incurring the environmental effects that the developed countries have experienced in the past. The author discusses the recently developed clean coal utilization technologies, their applications economies and feasibility of utilization with specific reference to Pakistan''s coal. (author)

Enhancement of Operating Efficiency Of The Central Coal-Preparation Plant of "MMK - UGOL" Ltd. Under Current Conditions

Science.gov (United States)

Basarygin, Maksim

2017-11-01

In this article the subject of enhancement of operating efficiency of the central coal-preparation plant of OOO "MMK-UGOL" is encompassed. Modern trends in the development of technologies and equipment for coal beneficiation are due to the following requirements: improving competitiveness of coal products, improvement of quality of marketable products, reduction of coal production cost, environmental requirements: polluting emission abatement, prepared coal saving, improvement of the effectiveness of resource conservation; complex mechanization and beneficiation process automation. In the article the contemporary problems of raw coal benefication under current conditions of the increased dilution of withdrawable coals with rock fractions are considered. Comparative analysis of efficiency of application of modern concentrating equipment under the conditions of the CCPP of OOO "MMK-UGOL" is carried out on the basis of research works. Particular attention is paid to dehydration of produced coal concentrate with content of volatile agents of more than 35.0% and content of fine-dispersed particles in flotation concentrate of more than 50.0%. Comparative analysis of the coal concentrate dehydration technologies is conducted.

The development of coal-based technologies for Department of Defense facilities. Technical progress report, September 1995 - March 1996

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Pisupati, S.V.; Scaroni, A.W. [and others

1996-10-01

The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of decreasing DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Activities this reporting period are summarized by phase. During this reporting period, the Phase I final report was completed. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included completing a study to identify appropriate SO{sub 2} and NO{sub x} control technologies for coal-fired industrial boilers. In addition, work continued on the design of a ceramic filtering device for installation on the demonstration boiler. The ceramic filtering device will be used to demonstrate a smaller and more efficient filtering device for retrofit applications. Work related to coal preparation and utilization, and the economic analysis was primarily focused on preparing the final report. Work in Phase III focused on coal preparation studies and economic analyses of coal use. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. The economic study focused on community sensitivity to coal usage, regional economic impacts of new coal utilization technologies, and constructing a national energy portfolio.

Biowaste utilization in the process of co-gasification with bituminous coal and lignite

International Nuclear Information System (INIS)

Howaniec, Natalia; Smoliński, Adam

2017-01-01

Biowaste utilization in co-gasification with bituminous coal and lignite gives the benefits of stable supplies of a primary energy source – coal and utilization of a zero-emission, waste material (i.e. agriculture waste, sewage sludge, etc.) with higher process efficiency and lower negative environmental impact than biomass or coal gasification, respectively. The main focus of the study presented is co-gasification of bituminous coal or lignite with biowaste to hydrogen-rich gas. The experiments were performed in the laboratory scale fixed-bed reactor installation at 700 and 900 °C. The Hierarchical Clustering Analysis complemented with a color map of studied data were applied in the selection of the optimal operating parameters for biowaste utilization in the co-gasification process based on the experimental data of gasification/co-gasification process as well as physical and chemical properties of fuels tested. The experimental results showed that the carbon conversion rate in co-gasification increased with increasing biomass content in a fuel. The total gas volume and hydrogen volume in co-gasification were higher than the values expected based on the results of the gasification process of the fuels analyzed. - Highlights: • Biowaste co-gasification with bituminous coal/lignite to hydrogen-rich gas. • Steam co-gasification in laboratory scale fixed-bed reactor at 700 and 900 °C. • Hierarchical Clustering Analysis complemented with color map of experimental data. • Carbon conversion increase with increasing biomass content. • The highest total gas and hydrogen volume in co-gasification of C-B20 blend at 900C.

Proceedings of the workshop on radioactivity associated with coal use

International Nuclear Information System (INIS)

1981-12-01

A workshop on radioactivity in coal use was held on September 15 through 17, 1981, under the auspices of the US Department of Energy, Office of Environmental Programs, and the Los Alamos National Laboratory. The purpose of the workshop was to identify research issues associated with radioactivity resulting from the use of coal for electric power generation. The concensus of the 10 scientists participating in the workshop was that a moderate to strong need exists for research in solubility of fly ash in different fluids and for determination of radioactivity in construction materials. Several additional research issues were identified but were given a lower priority. Summaries of each presentation are included. Titles are: some effects of coal combustion on the radiation environment; radionuclides in western coal at Mound; low-level radiation in coals utilized and ashes produced at New York State electric utilities; radioactivity from coal use - where are the problems; chemistry of radionuclides in coal preparation; uranium daughters in natural atmospheric aerosols and coal-fired power plant emissions; possible contributions of coal extraction and utilization to radioactivity contributions in drinking water; and impact on water quality from radionuclides in coal. One paper has been abstracted separately for inclusion in the Energy Data Base

Preparation of sintered foam materials by alkali-activated coal fly ash.

Science.gov (United States)

Zhao, Yelong; Ye, Junwei; Lu, Xiaobin; Liu, Mangang; Lin, Yuan; Gong, Weitao; Ning, Guiling

2010-02-15

Coal fly ash from coal fired power stations is a potential raw material for the production of ceramic tiles, bricks and blocks. Previous works have demonstrated that coal fly ash consists mainly of glassy spheres that are relatively resistant to reaction. An objective of this research was to investigate the effect of alkali on the preparation process of the foam material. Moreover, the influence of foam dosage on the water absorption, apparent density and compressive strength was evaluated. The experimental results showed that homogenous microstructures of interconnected pores could be obtained by adding 13 wt.% foaming agent at 1050 degrees C, leading to foams presenting water absorption, apparent density and compressive strength values of about 126.5%, 0.414 g/cm(3), 6.76 MPa, respectively.

Feasibility study on recovery and utilization of coal mine gas (CMG) at Donetsk Coal Field

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

For the purpose of getting petroleum substitution energy and reducing greenhouse effect gas emission, an investigational study was carried out of the project for methane gas recovery/utilization at the Donbassa coal mine in Ukraine. At the Donbassa coal mine, degassing by test boring is being conducted to reduce the gas emission at coal face for safety, but most of the gas is discharged into the air. In this project, the following were studied: degassing boring/gas induction from bore hole/measurement in gas induction pipe, gas recovery system combined with gas induction in flyash, and installation/operation of gas engine power generation facilities (1,710kW x 7 units) with exhaust heat recovery boiler using the recovered methane gas as fuel. The results obtained were the petroleum substitution amount of 31,000 toe/y and the amount of greenhouse effect gas reduction of 480,000 t/y. In the economical estimation, the initial investment amount was 3 billion yen, the profitability of the total investment used was 2.9%, and the internal earning rate was 6.5%. (NEDO)

The development of coal-based technologies for Department of Defense facilities. Semi-annual report, March 28, 1996--September 27, 1996

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Pisupati, S.V.; Scarone, A.W. [and others

1996-12-13

The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Fuel Technology, with the aim of decreasing DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Activities this reporting period are summarized by phase. Phase I was completed on November 1, 1995. Work on Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included continuing bench-scale tests to identify an NO{sub x} reduction catalyst which is appropriate for industrial boiler applications. In addition, installation of a ceramic filtering device on the demonstration boiler started. Also, a sodium bicarbonate duct injection system was procured for installation on the demonstration boiler. Work related to coal preparation and utilization, and the economic analysis was primarily focused on preparing the final report. Work in Phase III focused on coal preparation studies and economic analyses of coal use. Coal preparation studies were focused on continuing activities on particle size control, physical separations,surface-based separation processes, and dry processing. The economic study focused on community sensitivity to coal usage, regional/national economic impacts of new coal utilization technologies, and constructing a national energy portfolio.

Hard coal; Steinkohle

Energy Technology Data Exchange (ETDEWEB)

Loo, Kai van de; Sitte, Andreas-Peter [Gesamtverband Steinkohle e.V., Herne (Germany)

2013-04-01

The year 2012 benefited from a growth of the consumption of hard coal at the national level as well as at the international level. Worldwide, the hard coal still is the number one energy source for power generation. This leads to an increasing demand for power plant coal. In this year, the conversion of hard coal into electricity also increases in this year. In contrast to this, the demand for coking coal as well as for coke of the steel industry is still declining depending on the market conditions. The enhanced utilization of coal for the domestic power generation is due to the reduction of the nuclear power from a relatively bad year for wind power as well as reduced import prices and low CO{sub 2} prices. Both justify a significant price advantage for coal in comparison to the utilisation of natural gas in power plants. This was mainly due to the price erosion of the inexpensive US coal which partly was replaced by the expansion of shale gas on the domestic market. As a result of this, the inexpensive US coal looked for an outlet for sales in Europe. The domestic hard coal has continued the process of adaptation and phase-out as scheduled. Two further hard coal mines were decommissioned in the year 2012. RAG Aktiengesellschaft (Herne, Federal Republic of Germany) running the hard coal mining in this country begins with the preparations for the activities after the time of mining.

Biochemical Removal of HAP Precursors From Coal

Energy Technology Data Exchange (ETDEWEB)

Olson, G.; Tucker, L.; Richards, J.

1997-07-01

This project addresses DOE`s interest in advanced concepts for controlling emissions of air toxics from coal-fired utility boilers. We are determining the feasibility of developing a biochemical process for the precombustion removal of substantial percentages of 13 inorganic hazardous air pollutant (HAP) precursors from coal. These HAP precursors are Sb, As, Be, Cd, Cr, Cl, Co, F, Pb, Hg, Mn, Ni, and Se. Although rapid physical coal cleaning is done routinely in preparation plants, biochemical processes for removal of HAP precursors from coal potentially offer advantages of deeper cleaning, more specificity, and less coal loss. Compared to chemical processes for coal cleaning, biochemical processes potentially offer lower costs and milder process conditions. Pyrite oxidizing bacteria, most notably Thiobacillusferrooxidans, are being evaluated in this project for their ability to remove HAP precursors from U.S. coals.

Biochemical Removal of HAP Precursors From Coal

International Nuclear Information System (INIS)

Olson, G.; Tucker, L.; Richards, J.

1997-07-01

This project addresses DOE's interest in advanced concepts for controlling emissions of air toxics from coal-fired utility boilers. We are determining the feasibility of developing a biochemical process for the precombustion removal of substantial percentages of 13 inorganic hazardous air pollutant (HAP) precursors from coal. These HAP precursors are Sb, As, Be, Cd, Cr, Cl, Co, F, Pb, Hg, Mn, Ni, and Se. Although rapid physical coal cleaning is done routinely in preparation plants, biochemical processes for removal of HAP precursors from coal potentially offer advantages of deeper cleaning, more specificity, and less coal loss. Compared to chemical processes for coal cleaning, biochemical processes potentially offer lower costs and milder process conditions. Pyrite oxidizing bacteria, most notably Thiobacillusferrooxidans, are being evaluated in this project for their ability to remove HAP precursors from U.S. coals

Synergistic Utilization of Coal Fines and Municipal Solid Waste in Coal-Fired Boilers. Phase I Final Report

Energy Technology Data Exchange (ETDEWEB)

V. Zamansky; P. Maly; M. Klosky

1998-06-12

A feasibility study was performed on a novel concept: to synergistically utilize a blend of waste coal fines with so-called E-fuel for cofiring and reburning in utility and industrial boilers. The E-fuel is produced from MSW by the patented EnerTech's slurry carbonization process. The slurry carbonization technology economically converts MSW to a uniform, low-ash, low-sulfur, and essentially chlorine-free fuel with energy content of about 14,800 Btu/lb.

The development of coal-based technologies for Department of Defense facilities. Semiannual technical progress report, March 28, 1995--September 27, 1995

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Hatcher, P.; Knicker, H. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

1996-10-21

The U.S. Department of Defense (DOD), through the Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Mixture Technology, with the aim of decreasing DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Activities this reporting period are summarized by phase. During this reporting period, preparation of the Phase I final report continued. Work on Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included initiating a study to identify appropriate SO{sub 2} and NO{sub x} control technologies for coal-fired industrial boilers. In addition, work started on the design of a ceramic filtering device for installation on the demonstration boiler. The ceramic filter device will be used to demonstrate a more compact and efficient filtering device for retrofit applications. Coal preparation and utilization activities, and the economic analysis were completed and work focused on preparing the final report. Work on Phase III focused on coal preparation studies and economic analyses of coal use. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. The economic study focused on selecting incentives for commercialization of coal using technologies, community sensitivity to coal usage, regional economic impacts of new coal utilization technologies, and constructing a national energy portfolio.

Coal combustion waste management study

International Nuclear Information System (INIS)

1993-02-01

Coal-fired generation accounted for almost 55 percent of the production of electricity in the United States in 1990. Coal combustion generates high volumes of ash and flue gas desulfurization (FGD) wastes, estimated at almost 90 million tons. The amount of ash and flue gas desulfurization wastes generated by coal-fired power plants is expected to increase as a result of future demand growth, and as more plants comply with Title IV of the 1990 Clean Air Act Amendments. Nationwide, on average, over 30 percent of coal combustion wastes is currently recycled for use in various applications; the remaining percentage is ultimately disposed in waste management units. There are a significant number of on-site and off-site waste management units that are utilized by the electric utility industry to store or dispose of coal combustion waste. Table ES-1 summarizes the number of disposal units and estimates of waste contained at these unites by disposal unit operating status (i.e, operating or retired). Further, ICF Resources estimates that up to 120 new or replacement units may need to be constructed to service existing and new coal capacity by the year 2000. The two primary types of waste management units used by the industry are landfills and surface impoundments. Utility wastes have been exempted by Congress from RCRA Subtitle C hazardous waste regulation since 1980. As a result of this exemption, coal combustion wastes are currently being regulated under Subtitle D of RCRA. As provided under Subtitle D, wastes not classified as hazardous under Subtitle C are subject to State regulation. At the same time Congress developed this exemption, also known as the ''Bevill Exclusion,'' it directed EPA to prepare a report on coal combustion wastes and make recommendations on how they should be managed

Advanced clean coal utilization technologies

Energy Technology Data Exchange (ETDEWEB)

Moritomi, Hiroshi [National Inst. for Resources and Environment, Tsukuba, Ibaraki (Japan)

1993-12-31

The most important greenhouse gas is CO{sub 2} from coal utilization. Ways of mitigating CO{sub 2} emissions include the use of alternative fuels, using renewable resources and increasing the efficiency of power generation and end use. Adding to such greenhouse gas mitigation technologies, post combustion control by removing CO{sub 2} from power station flue gases and then storing or disposing it will be available. Although the post combustion control have to be evaluated in a systematic manner relating them to whether they are presently available technology, to be available in the near future or long term prospects requiring considerable development, it is considered to be a less promising option owing to the high cost and energy penalty. By contrast, abatement technologies aimed at improving conversion efficiency or reducing energy consumption will reduce emissions while having their own commercial justification.

Appalachian clean coal technology consortium

International Nuclear Information System (INIS)

Kutz, K.; Yoon, Roe-Hoan

1995-01-01

The Appalachian Clean Coal Technology Consortium (ACCTC) has been established to help U.S. coal producers, particularly those in the Appalachian region, increase the production of lower-sulfur coal. The cooperative research conducted as part of the consortium activities will help utilities meet the emissions standards established by the 1990 Clean Air Act Amendments, enhance the competitiveness of U.S. coals in the world market, create jobs in economically-depressed coal producing regions, and reduce U.S. dependence on foreign energy supplies. The research activities will be conducted in cooperation with coal companies, equipment manufacturers, and A ampersand E firms working in the Appalachian coal fields. This approach is consistent with President Clinton's initiative in establishing Regional Technology Alliances to meet regional needs through technology development in cooperation with industry. The consortium activities are complementary to the High-Efficiency Preparation program of the Pittsburgh Energy Technology Center, but are broader in scope as they are inclusive of technology developments for both near-term and long-term applications, technology transfer, and training a highly-skilled work force

Appalachian clean coal technology consortium

Energy Technology Data Exchange (ETDEWEB)

Kutz, K.; Yoon, Roe-Hoan [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States)

1995-11-01

The Appalachian Clean Coal Technology Consortium (ACCTC) has been established to help U.S. coal producers, particularly those in the Appalachian region, increase the production of lower-sulfur coal. The cooperative research conducted as part of the consortium activities will help utilities meet the emissions standards established by the 1990 Clean Air Act Amendments, enhance the competitiveness of U.S. coals in the world market, create jobs in economically-depressed coal producing regions, and reduce U.S. dependence on foreign energy supplies. The research activities will be conducted in cooperation with coal companies, equipment manufacturers, and A&E firms working in the Appalachian coal fields. This approach is consistent with President Clinton`s initiative in establishing Regional Technology Alliances to meet regional needs through technology development in cooperation with industry. The consortium activities are complementary to the High-Efficiency Preparation program of the Pittsburgh Energy Technology Center, but are broader in scope as they are inclusive of technology developments for both near-term and long-term applications, technology transfer, and training a highly-skilled work force.

Dispatcher's monitoring systems of coal preparation processes. Systemy dyspozytorskiej kontroli procesow wzbogacania wegla

Energy Technology Data Exchange (ETDEWEB)

Cierpisz, S [Politechnika Slaska, Gliwice (Poland); Cierpisz, T; Glowacki, D; Puczylowski, T [Min-Tech Sp. z o.o., Katowice (Poland)

1994-08-01

The computer-based control and dispatcher's monitoring systems for coal preparation plants are described. The article refers to the local automation systems of coal blending production, control systems of heavy media separation process and dispatcher's visualization systems of technological lines operation. The effects of implementation of the above mentioned systems as well as some experiences gained at the designing and operational stages are given. (author). 2 refs., 6 figs.

Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Environmentally acceptable coal utilization system feasibility survey in Malaysia and Vietnam (Malaysia); 1997 nendo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Malaysia oyobi Vietnam ni okeru kankyo chowagata sekitan riyo system kanosei chosa (Malaysia ban))

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

In this survey, the coal utilization status in individual consumption sectors and coal distribution status in Malaysia are summarized as basic data for the introduction of environmentally acceptable coal utilization systems. In this fiscal year, the status of existing coal utilization technology and environmental issues in Malaysia are summarized as basic data for the introduction of above-mentioned systems on the basis of data and information collected by basic research and site survey in FY 1996. Malaysia is one of the rich countries producing the primary resources with crude petroleum, natural gas, hydro-power, and coal. The coal demand will be realized after saturating LNG development since 2000. The major coal consumption industries are power generation sector and cement industry sector. As expected increase in the future coal consumption, efficiency of coal utilization and environmental issues are problems in the future. Based on the FS results of this survey, the survey will be continued for planning and conducting the model project required from Malaysia. 8 figs., 34 tabs.

Coal supplier perspective on the future of the utility-coal industry

Energy Technology Data Exchange (ETDEWEB)

Goldberg, G.J. [Kennecott Energy Company, Gillette, WY (United States)

2000-07-01

Kennecott Energy is the largest producer within Rio Tinto Energy, in turn owned by Rio Tinto, and has grown by 260% since 1993. However, coal's performance in the world trade market is currently suffering for reasons such as regulatory uncertainty. The presentation looked at how the company is striving to improve coal's future, for example by enhancing coal's value through beneficiation like K-fuels, enhancing pollution control through research efforts like Zero Emissions Coal Alliance and by supporting public outreach and legislation efforts. Coal's future is summed up under headings: earnings, efficiency, environment, education and e-commerce. 17 overheads/viewgraphs outline the presentation.

Potential to cofire high-sulfur coal and MSW/RDF in Illinois utility boilers: A survey and analysis

International Nuclear Information System (INIS)

South, D.W.

1993-01-01

The disposal of refuse is of ever-increasing concern for municipalities and other organizations and agencies throughout the United States. Disposal in landfills is becoming more costly, and new landfills are more difficult to site because of stricter environmental regulations. Mass burning incinerators for municipal solid wastes (MSW) have also met with increased public resistance due to excessive emissions. Nevertheless, increased awareness of the need for alternative disposal techniques has led to a new interest in cofiring MSW with coal. In addition to solid waste concerns, the requirements to reduce SO 2 and NO x emissions from coal-fired utility boilers in the Clean Air Act Amendments of 1990, present an opportunity to cofire MSW/RDF with coal as an emission control measure. These issues were the impetus for a 1992 study (conducted by ANL for the Illinois Clean Coal Institute) to examine the potential to cofire coal with MSW/RDF in Illinois utility boilers. This paper will provide a synopsis of the ANL/ICCI report. It will summarize (1) the combustibility and emission characteristics of high-sulfur coal and MSW/RDF; (2) the facilities firing RDF and/or producing/selling RDF, together with their combustion and emissions experience; (3) the applicable emissions regulations in Illinois; and (4) the analysis of candidate utility boilers in Illinois capable of cofiring, together with the effect on coal consumption and SO 2 and NO x emissions that would result from 20% cofiring with RDF/MSW

Environmentally friendly type coal utilization technology transfer project. Downstream field; Kankyo chowagata sekitan riyo gijutsu iten jigyo. Karyu bun`ya

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper arranged the result of the clean coal technology transfer project carried out during October to December, 1996. For the purpose of supporting introduction/spread of clean coal technology (CCT) in Asian and Pacific countries, the project invited engineers of the countries to Japan, aiming at fermentation of the understanding of CCT and improvement in ability. The project was held by NEDO and managed by Center for Coal Utilization, Japan. The manager course is for policy decision makers, management and senior management (plant manager class). By taking up CCT assessment and a menu of economical efficiency, prepared was the environment to which CCT is introduced in case of working out policy and planning plant/equipment investment. Moreover, the engineer course is for policy planners, medium-class management (section chief class), senior engineers (planners), and takes up materials for judgment in case of planning CCT facilities and proposing measures to reduce environmental loads by management and improvement of facilities at the same time. Fifteen engineers were invited: 6 from China, 3 from Indonesia, 3 from the Philippines, and 3 from Thailand

Parametric utility comparison of coal and nuclear electricity generation

International Nuclear Information System (INIS)

Maurer, K.M.

1977-02-01

The advantages and limitations of an explicit quantitative model for decision making are discussed. Several different quantitative models are presented, noting that the use of an expected utility maximization decision rule allows both the direct incorporation of multidimensional descriptions of the possible outcomes, and considerations of risk averse behavior. A broad class of utility functions, characterized by linear risk tolerance, was considered and extended to a multidimensional form. Choosing a multivariate risk neutral extension, using constant absolute risk aversion utility functions for monetary effects and for increased mortality, the author indicated how the parameters of this utility function can be selected to represent the decision maker's preferences, and suggest a reasonable range of values for the parameters. After describing an illustrative set of data on the risks inherent in coal burning and nuclear electricity generation facilities, the author used the chosen utility model to compare the overall risks associated with each technology, observing the effect of variations in the utility parameters and in the risk distributions on the implied preferences

Coal Tar and Coal-Tar Pitch

Science.gov (United States)

Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

Fourth annual conference on materials for coal conversion and utilization

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

The fourth annual conference on materials for coal conversion and utilization was held October 9 to 11, 1979, at the National Bureau of Standards, Gaithersburg, Maryland. It was sponsored by the National Bureau of Standards, the Electric Power Research Institute, the US Department of Energy, and the Gas Research Institute. The papers have been entered individually into EDB and ERA. (LTN)

International Coal Report's coal year 1991

Energy Technology Data Exchange (ETDEWEB)

McCloskey, G [ed.

1991-05-31

Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

Low-rank coal research. Quarterly report, January--March 1990

Energy Technology Data Exchange (ETDEWEB)

1990-08-01

This document contains several quarterly progress reports for low-rank coal research that was performed from January-March 1990. Reports in Control Technology and Coal Preparation Research are in Flue Gas Cleanup, Waste Management, and Regional Energy Policy Program for the Northern Great Plains. Reports in Advanced Research and Technology Development are presented in Turbine Combustion Phenomena, Combustion Inorganic Transformation (two sections), Liquefaction Reactivity of Low-Rank Coals, Gasification Ash and Slag Characterization, and Coal Science. Reports in Combustion Research cover Fluidized-Bed Combustion, Beneficiation of Low-Rank Coals, Combustion Characterization of Low-Rank Coal Fuels, Diesel Utilization of Low-Rank Coals, and Produce and Characterize HWD (hot-water drying) Fuels for Heat Engine Applications. Liquefaction Research is reported in Low-Rank Coal Direct Liquefaction. Gasification Research progress is discussed for Production of Hydrogen and By-Products from Coal and for Chemistry of Sulfur Removal in Mild Gas.

National Coal Utilization Assessment: a preliminary assessment of coal utilizaton in the South. [Southern USA to 2020; forecasting

Energy Technology Data Exchange (ETDEWEB)

Berry, L. B.; Bjornstad, D. J.; Boercker, F. D.

1978-01-01

Some of the major problems and issues related to coal development and use in the South are identified and assessed assuming a base-case energy scenario for the next 45 years. This scenario assumes a midrange of coal use and a relatively high rate of nuclear use over the forecast period. The potential impacts from coal development and use are significant, particularly in the 1990-2020 time period. Practically all available sites suitable for power plant development in the assessment will be utilized by 2020. Overall, sulfur dioxide will be well below the annual primary standard; however, several local hot-spot areas were identified. In addition, sulfate concentrations will be increased significantly, particularly over Virginia, West Virginia, and northern Kentucky. Coal mining is expected to affect 6 of the 12 major ecological regions. Coal mining will lead to increased average suspended sediment concentrations in some river basins, and special measures will be required to control acid discharges from active mines in pyritic regions. The increased mining of coal and subsequent sulfur dioxide increases from its combustion may also give rise to a land-use confrontation with food and fiber production. Potential health effects from exposure to sulfur dioxide and sulfates are expected to increase rapidly in several areas, particularly in parts of Kentucky, Maryland, District of Columbia, and Georgia. Regional social costs should be relatively low, although some site-specific costs are expected to be very high. Alternative energy technologies, careful siting selection, and deployment of environmental control technologies and operating policies will be required to reduce or mitigate these potential impacts.

Illustrative comparison of one utility's coal and nuclear choices

International Nuclear Information System (INIS)

Keeney, R.L.; Sicherman, A.

1983-01-01

The technology choices facing an individual utility are complex decision problems. The paper illustrates a method designed to assist an individual utility company in making the choices in a logically consisnt manner. The resulting evaluation model, based on the principles of decision analysis, explicitly addresses the complexity to provide a basis for decision making and support for defending the decision before reviewers. The model, which incorporates economic, environmental, social, safety, and regulatory effects, is demonstrated using a coal/nuclear choice which may be faced by Utah Power and Light Company in the near future. This analysis is meant to be illustrative; more effort would be needed to gather information to support a policy decision

UTILIZATION OF LIGHTWEIGHT MATERIALS MADE FROM COAL GASIFICATION SLAGS

International Nuclear Information System (INIS)

None

1998-01-01

The integrated-gasification combined-cycle (IGCC) process is an emerging technology that utilizes coal for power generation and production of chemical feedstocks. However, the process generates large amounts of solid waste, consisting of vitrified ash (slag) and some unconverted carbon. In previous projects, Praxis investigated the utilization of ''as-generated'' slags for a wide variety of applications in road construction, cement and concrete production, agricultural applications, and as a landfill material. From these studies, we found that it would be extremely difficult for ''as-generated'' slag to find large-scale acceptance in the marketplace even at no cost because the materials it could replace were abundantly available at very low cost. It was further determined that the unconverted carbon, or char, in the slag is detrimental to its utilization as sand or fine aggregate. It became apparent that a more promising approach would be to develop a variety of value-added products from slag that meet specific industry requirements. This approach was made feasible by the discovery that slag undergoes expansion and forms a lightweight material when subjected to controlled heating in a kiln at temperatures between 1400 and 1700 F. These results confirmed the potential for using expanded slag as a substitute for conventional lightweight aggregates (LWA). The technology to produce lightweight and ultra-lightweight aggregates (ULWA) from slag was subsequently developed by Praxis with funding from the Electric Power Research Institute (EPRI), Illinois Clean Coal Institute (ICCI), and internal resources. The major objectives of the subject project are to demonstrate the technical and economic viability of commercial production of LWA and ULWA from slag and to test the suitability of these aggregates for various applications. The project goals are to be accomplished in two phases: Phase I, comprising the production of LWA and ULWA from slag at the large pilot scale, and

Coal development potential in Pakistan

Energy Technology Data Exchange (ETDEWEB)

Khan, M N; Pelofsky, A H [eds.

1986-01-01

A total of 48 papers were presented, and covered the following topics: the current situation in Pakistan with respect to development and utilization of coal resources; the policies that have been responsible for the development and utilization of coal resources in Pakistan; coal development and utilization in other developing nations e.g. Indonesia, Greece, Philippines, China, Thailand and Haiti; and technological developments in coal exploration; extraction, handling, transport and utilization which could accelerate future development of Pakistan's coal resources. Specific subjects covered include the use of coal in the cement industry of Pakistan; the production of briquettes for domestic use, development and training of personnel for the coal industry; and sources of finance for coal development projects. Particular emphasis is given throughout the conference to the Lakhra coal mine/power plant project which aims to develop and effectively utilize the lignite reserves of Sind Province. 47 papers have been abstracted separately.

Characterization and supply of coal based fuels

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

Studies and data applicable for fuel markets and coal resource assessments were reviewed and evaluated to provide both guidelines and specifications for premium quality coal-based fuels. The fuels supplied under this contract were provided for testing of advanced combustors being developed under Pittsburgh Energy Technology Center (PETC) sponsorship for use in the residential, commercial and light industrial (RCLI) market sectors. The requirements of the combustor development contractors were surveyed and periodically updated to satisfy the evolving needs based on design and test experience. Available coals were screened and candidate coals were selected for further detailed characterization and preparation for delivery. A team of participants was assembled to provide fuels in both coal-water fuel (CWF) and dry ultrafine coal (DUC) forms. Information about major US coal fields was correlated with market needs analysis. Coal fields with major reserves of low sulfur coal that could be potentially amenable to premium coal-based fuels specifications were identified. The fuels requirements were focused in terms of market, equipment and resource constraints. With this basis, the coals selected for developmental testing satisfy the most stringent fuel requirements and utilize available current deep-cleaning capabilities.

CONTROL OF NOX EMISSIONS FROM U.S. COAL-FIRED ELECTRIC UTILITY BOILERS

Science.gov (United States)

The paper discusses the control of nitrogen oxide (NOx) emissions from U.S. coal-fired electric utility boilers. (NOTE: In general, NOx control technologies are categorized as being either primary or secondary control technologies. Primary technologies reduce the amount of NOx pr...

The increase of the efficiency for comprehensive utilization of the fuel and energetic resources (The use coal enterprises of Kazakhstan as example)

International Nuclear Information System (INIS)

Satova, R.K.

1999-01-01

In Kazakhstan during the period of transition to the market economy in the condition of reduction of coal production and increasing expenditures in coal branch, the problem of of the rational utilization of coal resources becomes the most vital issue. In the thesis theoretical and methodological aspects of socio-economic efficiency of utilization of the fuel and energetic resources are investigated. Different fields of usage of coal and coal wastes are studied, economic evaluation of mechanic and thermo-chemical methods of producing coal in process of bringing resources saving technologies; the national efficiency of using products in the quantity of technological raw and energetic fuel is brought out; the influence refining for the widening of the raw-base of industry, promoting the economic results of production and the lowering environmental pollution. It was estimated that the extracted coal of the region includes 1020 thousand tonne of aluminium oxide and 996 thousand tonne of sulphur; in the course of extracting and coal processing 3650 thousand tonne of firm wastes appeared; during the extracting of Ehkibastuz coal - 90970 thousand tonne, and the Karaganda coal - 40040 thousand tonne.The coal components and wastes mentioned above should be considered not only as source of environment pollution but also as potential resource for the production of industrial goods according to their qualitative characteristics and the availability of technical ideas of the processing. The implementation of the mentioned pre-sup-positions in the conditions of the forming market economy will allow to use the organic part of coal more competently, to involve the other useful components of coal in the sphere of production consumption, to utilize gaseous and firm wastes and to gain of the basis the expansion of resource base of same branches of industry and the reduction of environment pollution. It will be also accompanied by the needs in capital investments for the industrial

General programme of energy research: innovation in hard coal, 1974-1977. Preparation and surface facilities. Rahmenprogramm Energieforschung: Innovation Steinkohle, 1974-1977. Aufbereitung und Tagesanlagen)

Energy Technology Data Exchange (ETDEWEB)

1979-01-01

Under the program Preparation and Surface Facilities initiated by the Federal Ministry of Economy of the FRG financial support in the amount of 50% (approx. 17 million DM) of the total project costs was allocated to eight applicants from the mining industry. The Ministry subsidized 15 research projects in the field of coal preparation and handling dealing with: surface blending and storage facilities; the development of a solid bowl centrifuge, steam cowl filter, and reciprocating centrifuge for dewatering coal fines; development of a jig and a screen sizer for coal sizing; clarification units and combustion of waste slurries in a fluidized-bed furnace; computerized monitoring of coal flow in surface and underground installations; the development of a conception for preparing coal otherwise difficult to prepare; and the development of the Olifloc method for agglomeration of coal fines sludge and separation from tailings. (In German)

Basic research program for innovated coal utilization in Japan. BRAIN-C program; Sekitan riyo kiban gijutsu kaihatsu. BRAIN-C program

Energy Technology Data Exchange (ETDEWEB)

Harada, M [Center for Coal Utilization, Japan, Tokyo (Japan)

1996-09-01

This paper introduces the circumstances and purpose of establishing the Basic Research Associate for Innovated Coal Utilization (BRAIN-C) Program started in October 1995, and the summary of the results therefrom in fiscal 1995. Although development of coal utilization technologies has been implemented over a number of years, there are many problems still requiring solutions. Early realization has been urged on diversification of coal utilization, acceleration of technological development and diversification of coal types. In order to achieve these goals, the necessity was recognized afresh on not only the hardwares, but also on basic technologies in terms of software which can identify properties of coals, systematize different reactions, and estimate reactions, fluidity and heat transmission of coals. Therefore, receiving a subsidy from the Agency of Natural Resources and Energy of the Ministry of International Trade and Industry, a research and development program to be implemented jointly by industries, administrative agencies and academic societies had been started with a five-year plan for the time being. With the activities for the program such as collecting 50 to 100 types of coals and supplying them to researchers, the program had been accelerated in fiscal 1995 on a large number of themes and results therefrom, including fundamental properties and thermo-chemical reactions. 2 figs., 4 tabs.

Fiscal 1995 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system` (interim report); 1995 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku: sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho (chukan hokoku)

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The coal utilization is expected to make substantial growth according to the long-term energy supply/demand plan. To further expand the future coal utilization, however, it is indispensable to reduce environmental loads in its total use with other energies, based on the coal use. In this survey, a regional model survey was conducted as environmental load reduction measures using highly cleaned coal which were taken in fiscal 1993 and 1994. Concretely, a model system was assumed which combined facilities for mixed combustion with coal and other energy (hull, bagasse, waste, etc.) and facilities for effective use of burned ash, and potential reduction in environmental loads of the model system was studied. The technology of mixed combustion between coal and other energy is still in a developmental stage with no novelties in the country. Therefore, the mixed combustion technology between coal and other energy is an important field which is very useful for the future energy supply/demand and environmental issues. 34 refs., 27 figs., 48 tabs.

Firing a sub-bituminous coal in pulverized coal boilers configured for bituminous coals

Energy Technology Data Exchange (ETDEWEB)

N. Spitz; R. Saveliev; M. Perelman; E. Korytni; B. Chudnovsky; A. Talanker; E. Bar-Ziv [Ben-Gurion University of the Negev, Beer-Sheva (Israel)

2008-07-15

It is important to adapt utility boilers to sub-bituminous coals to take advantage of their environmental benefits while limiting operation risks. We discuss the performance impact that Adaro, an Indonesian sub-bituminous coal with high moisture content, has on opposite-wall and tangentially-fired utility boilers which were designed for bituminous coals. Numerical simulations were made with GLACIER, a computational-fluid-dynamic code, to depict combustion behavior. The predictions were verified with full-scale test results. For analysis of the operational parameters for firing Adaro coal in both boilers, we used EXPERT system, an on-line supervision system developed by Israel Electric Corporation. It was concluded that firing Adaro coal, compared to a typical bituminous coal, lowers NOx and SO{sub 2} emissions, lowers LOI content and improves fouling behavior but can cause load limitation which impacts flexible operation. 21 refs., 7 figs., 3 tabs.

Adsorption of SO2 on bituminous coal char and activated carbon fiber prepared from phenol formaldehyde

Science.gov (United States)

DeBarr, Joseph A.; Lizzio, Anthony A.; Daley, Michael A.

1996-01-01

Carbon-based materials are used commercially to remove SO2 from coal combustion flue gases. Historically, these materials have consisted of granular activated carbons prepared from lignite or bituminous coal. Recent studies have reported that activated carbon fibers (ACFs) may have potential in this application due to their relatively high SO2 adsorption capacity. In this paper, a comparison of SO2 adsorption for both coal-based carbons and ACFs is presented, as well as ideas on carbon properties that may influence SO2 adsorption

Fiscal 1995 survey report on the feasibility study of the environmentally friendly type coal utilization system. Feasibility study of the environmentally friendly type coal utilization system in Thailand; Kankyo chowagata sekitan riyo system kanosei chosa. Tai ni okeru kankyo chowagata sekitan riyo system kanosei chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

The paper surveyed the present situation and future trend of economy, energy supply/demand, coal production/distribution/utilization and the environmental effects in Thailand. The survey on the coal utilization and its environmental effects was partially requested of the environmental research institute in Thailand. The amount of coal utilization in Thailand rapidly increased to nearly four times as large as that ten years ago mainly in terms of domestic lignite under the government`s policy on expansion of the domestic energy use. However, most of this domestic lignite is low-grade coal with low calories and high sulfur content, and the use of it was rapidly increased mostly in power generation sector without no adequate environmental measures taken. This caused an environmental problem on air pollution due to sulfur oxides at Mae Moh power plant in the north several years ago, and the damages to the regional residents, etc. were given much publicity by journalism and developed the social problem. Accordingly, Thai people are now critical of the coal resource exploration and the coal use expansion. Under the circumstances, the Ministry of Industry and the energy related ministries/offices are obliged to review their development/promotion plans. 84 figs., 99 tabs.

South Blackwater Coal`s maintenance program

Energy Technology Data Exchange (ETDEWEB)

Nash, J. [South Blackwater Coal Limited, Blackwater, Qld. (Australia)

1998-09-01

The South Blackwater operation consists of two opencut mining areas and two underground mines (Laleham and Kenmure) near Blackwater in central Queensland, all of which supply coal to a central coal preparation plant. South Blackwater Coal Ltd. recently developed a maintenance improvement programme, described in this article. The programme involved implementation systems of key performance indicators (KPIs), benchmaking, condition monitoring, work planning and control, failure analysis and maintenance audit. Some improvements became almost immediately apparent, others were quite gradual. Major results included: improved availability (and reliability) of all opencast fleets, improvements in rear dump availability; reduced maintenance man-hours for opencast fleets; and increased availability of the coal handling and preparation plant. The paper is an edited version of that presented at the `Maintenance in mining conference` 16-19 March 1998, held in Bali, Indonesia. 4 figs., 2 photos.

JV Task 126 - Mercury Control Technologies for Electric Utilities Burning Bituminous Coal

Energy Technology Data Exchange (ETDEWEB)

Jason Laumb; John Kay; Michael Jones; Brandon Pavlish; Nicholas Lentz; Donald McCollor; Kevin Galbreath

2009-03-29

The EERC developed an applied research consortium project to test cost-effective mercury (Hg) control technologies for utilities burning bituminous coals. The project goal was to test innovative Hg control technologies that have the potential to reduce Hg emissions from bituminous coal-fired power plants by {ge}90% at costs of one-half to three-quarters of current estimates for activated carbon injection (ACI). Hg control technology evaluations were performed using the EERC's combustion test facility (CTF). The CTF was fired on pulverized bituminous coals at 550,000 Btu/hr (580 MJ/hr). The CTF was configured with the following air pollution control devices (APCDs): selective catalytic reduction (SCR) unit, electrostatic precipitator (ESP), and wet flue gas desulfurization system (WFDS). The Hg control technologies investigated as part of this project included ACI (three Norit Americas, Inc., and eleven Envergex sorbents), elemental mercury (Hg{sup 0}) oxidation catalysts (i.e., the noble metals in Hitachi Zosen, Cormetech, and Hitachi SCR catalysts), sorbent enhancement additives (SEAs) (a proprietary EERC additive, trona, and limestone), and blending with a Powder River Basin (PRB) subbituminous coal. These Hg control technologies were evaluated separately, and many were also tested in combination.

Coal contract cost reduction through resale of coal

International Nuclear Information System (INIS)

Simon, R.

1990-01-01

The weak coal market of the 1980's has enabled utilities and other users of coal to enjoy stable or falling prices for coal supplies. Falling prices for coal stimulated the renegotiation of numerous coal contracts in recent years, as buyers look to take advantage of lower fuel prices available in the marketplace. This paper examines the use of coal resale transactions as a means of reducing fuel costs, and analyzes the benefits and risks associated with such transactions

Coal in Asia-Pacific. Vo1 7, No. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

In China, there are bottle-necks of the coal transportation capacity in the major inter-regional routes. The Chinese Government`s eighth and ninth five-year plans intend to increase the capacity. In the 9% growth case, the planned railway transport capacity will be critical. Measures are considered, as to promotion of coal dressing, transport as electric power, construction of nuclear power plants and hydraulic power plants, and construction of coal water slurry pipe lines. Japan`s coal policy includes the structural adjustment of coal mining industry, and a new policy for coal in the total energy policy. To secure the stable overseas coal supply, NEDO has a leading part in overseas coal resources development. Coal demand and supply, mining technology, mine safety, coal preparation and processing technology, and comprehensive coal utilization technology including clean coal technology in Japan are described. At present, Thailand is progressing with the seventh plan, and the development of domestic energy emphasize lignite, natural gas, and oil. Thai import demand for high-quality coal is to be increasing. Japan`s cooperation is considered to be effective for the environmental problems. 12 figs., 40 tabs.

Clean coal technology. Coal utilisation by-products

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-08-15

The need to remove the bulk of ash contained in flue gas from coal-fired power plants coupled with increasingly strict environmental regulations in the USA result in increased generation of solid materials referred to as coal utilisation by-products, or CUBs. More than 40% of CUBs were sold or reused in the USA in 2004 compared to less than 25% in 1996. A goal of 50% utilization has been established for 2010. The American Coal Ash Association (ACCA) together with the US Department of Energy's Power Plant Improvement Initiative (PPPI) and Clean Coal Power Initiative (CCPI) sponsor a number of projects that promote CUB utilization. Several are mentioned in this report. Report sections are: Executive summary; Introduction; Where do CUBs come from?; Market analysis; DOE-sponsored CUB demonstrations; Examples of best-practice utilization of CUB materials; Factors limiting the use of CUBs; and Conclusions. 14 refs., 1 fig., 5 tabs., 14 photos.

Cofiring of biofuels in coal fired boilers: Results of case study analysis

Energy Technology Data Exchange (ETDEWEB)

Tillman, D.A. [Ebasco Environmental, Sacramento, CA (United States); Hughes, E. [Electric Power Research Institute, Palo Alto, CA (United States); Gold, B.A. [TVA, Chattanooga, TN (United States)

1993-12-31

Ebasco Environmental and Reaction Engineering, under contract to EPRI, performed a case study analysis of cofiring biomass in coal-fired boilers of the Tennessee Valley Authority (TVA). The study was also sponsored by DOE. This analysis included evaluating wood fuel receiving, preparation, and combustion in pulverized coal (PC) boilers and cyclone furnaces and an assessment of converting wood into pyrolysis oil or low Btu gas for use in a new combined cycle combustion turbine (CCCT) installation. Cofiring wood in existing coal-fired boilers has the most immediate potential for increasing the utilization of biofuels in electricity generation. Cofiring biofuels with coal can potentially generate significant benefits for utilities including: (1) reducing emissions of SO{sub 2} and NO{sub x}; (2) reducing the net emissions of CO{sub 2}; (3) potentially reducing the fuel cost to the utility depending upon local conditions and considering biomass is potentially exempt from the proposed Btu tax and may get a 1.5 cent/kWh credit for energy generated by wood combustion; (4) supporting local industrial forest industry; and (5) providing a long term market for the development of a biofuel supply and delivery industry. Potential benefits are reviewed in the context of cofiring biofuel at a rate of 15% heat input to the boiler, and compares this cofiring strategy and others previously tested or developed by other utilities. Other issues discussed include: (1) wood fuel specifications as a function of firing method; (2) wood fuel receiving and preparation system requirements; (3) combustion system requirements for cofiring biofuels with coal; (4) combustion impacts of firing biofuels with coal; (5) system engineering issues; (6) the economics of cofiring biofuel with coal. The Allen, TN 330 MW(e) cyclone boiler and Kingston, TN 135 MW(e) Boiler {number_sign}1, a tangentially fired PC unit, case studies are then summarized in the paper, highlighting the cofiring opportunities.

Reactivity of coal chars prepared in a fluidised bed reactor at different burn-off degrees

Energy Technology Data Exchange (ETDEWEB)

Moreno, A.H.; Arenillas, A.; Rubiera, F.; Fuente, E.; Pis, J.J. [Inst. Nacional del Carbon, Oviedo (Spain)

1997-12-31

The main goal of this work has been to study the effect of the textural properties of coal chars, obtained from partially burned coal, on their reactivity to oxygen. A low volatile bituminous coal was used to prepare chars, with different levels of burn-off, in a bench-scale fluidised bed reactor. Textural characterisation of the samples was accomplished by measuring true (helium) and apparent (mercury) densities, and mercury porosimetry. An increase in the burn-off degree gave rise to a densification of the chars. Porosity development greatly changed during progressive burning of the samples. DTG burning profiles and isothermal gasification were utilised to estimate the reactivities of the precursor coal and its partially burned chars. Reactivity reached a maximum value at an intermediate burn-off and strongly decreased at higher burn-off degrees. (orig.)

A newer concept of setting up coal refineries in coal utilising industries through environmentally sound clean coal technology of organosuper refining of coals

International Nuclear Information System (INIS)

Sharma, D.K.

1994-01-01

In order to reduce the losses of premium organic matter of coal and its immense potential energy which is present in the form of stronger interatomic and intramolecular bonding energies, a newer and convenient technique of recovering the premium organic matter from low grade coals by organosuper-refining technique which operates under ambient pressure conditions has been developed. The residual coal obtained can be used as environmentally clean fuel or as a feedstock for the industries based on carbonization and gasification. It is suggested that a beginning be made by setting up coal refineries in coal utilizing industries on the basis of the presently developed new technology of organosuper-refining of coals to recover premium grade organic chemical feed stocks from coals before utilizing coal by techniques such as bubble bed or recirculatory fluidized bed or pulverized coal combustion in thermal power stations, carbonization in steel plants or other carbonization units, gasification in fertilizer industries or in integrated coal gasification combined cycle power generation. Thus, coal refineries may produce value added aromatic chemical feed stocks, formed coke or coke manufacturing; and carbon fillers for polymers. (author). 100 refs., 1 fig

Innovative clean coal technology (ICCT): demonstration of selective catalytic reduction (SCR) technology for the control of nitrogen oxide (NOx) emission from high-sulfur, coal-fired boilers - economic evaluation of commercial-scale SCR applications for utility boilers

International Nuclear Information System (INIS)

Healy, E.C.; Maxwell, J.D.; Hinton, W.S.

1996-09-01

This report presents the results of an economic evaluation produced as part of the Innovative Clean Coal Technology project, which demonstrated selective catalytic reduction (SCR) technology for reduction of NO x emissions from utility boilers burning U.S. high-sulfur coal. The document includes a commercial-scale capital and O ampersand M cost evaluation of SCR technology applied to a new facility, coal-fired boiler utilizing high-sulfur U.S. coal. The base case presented herein determines the total capital requirement, fixed and variable operating costs, and levelized costs for a new 250-MW pulverized coal utility boiler operating with a 60-percent NO x removal. Sensitivity evaluations are included to demonstrate the variation in cost due to changes in process variables and assumptions. This report also presents the results of a study completed by SCS to determine the cost and technical feasibility of retrofitting SCR technology to selected coal-fired generating units within the Southern electric system

Bio-coal briquettes using low-grade coal

Science.gov (United States)

Estiaty, L. M.; Fatimah, D.; Widodo

2018-02-01

The technology in using briquettes for fuel has been widely used in many countries for both domestic and industrial purposes. Common types of briquette used are coal, peat, charcoal, and biomass. Several researches have been carried out in regards to the production and the use of briquettes. Recently, researches show that mixing coal and biomass will result in an environmentally friendly briquette with better combustion and physical characteristics. This type of briquette is known as bio-coal briquettes. Bio-coal briquettes are made from agriculture waste and coal, which are readily available, cheap and affordable. Researchers make these bio-coal briquettes with different aims and objectives, depending on the issues to address, e.g. utilizing agricultural waste as an alternative energy to replace fossil fuels that are depleting its reserves, adding coal to biomass in order to add calorific value to bio-coal briquette, and adding biomass to coal to improve its chemical and physical properties. In our research, biocoal briquettes are made to utilize low grade coal. The biomass we use, however, is different from the ones used in past researches because it has undergone fermentation. The benefits of using such biomass are 1. Fermentation turns the hemi cellulose into a simpler form, so that the burning activation energy decreases while the calorific value increases. 2. Enzym produced will bind to heavy metals from coal as co-factors, forming metals that are environmentally friendly.

Plant concept of heat utilization of high temperature gas-cooled reactors. Co-generation and coal-gasification

International Nuclear Information System (INIS)

Tonogouchi, M.; Maeda, S.; Ide, A.

1996-01-01

In Japan, JAERI is now constructing the High temperature Engineering Test Reactor (HTTR) and the new era is coming for the development and utilization of HTR. Recognizing that the heat utilization of HTR would mitigate problems of environment and resources and contribute the effective use and steady supply of the energy, FAPIG organized a working group named 'HTR-HUC' to study the heat utilization of HTR in the field other than electric power generation. We chose three kinds of plants to study, 1) a co-generation plant in which the existing power units supplying steam and electricity can be replaced by a nuclear plant, 2) Coal gasification plant which can accelerate the clean use of coal and contribute stable supply of the energy and preservation of the environment in the world and 3) Hydrogen production plant which can help to break off the use of the new energy carrier HYDROGEN and will release people from the dependence of fossil energy. In this paper the former two plants, Co-generation chemical plant and Coal-gasification plant are focussed on. The main features, process flow and safety assessment of these plants are discussed. (J.P.N.)

Projections of air toxic emissions from coal-fired utility combustion: Input for hazardous air pollutant regulators

International Nuclear Information System (INIS)

Szpunar, C.B.

1993-01-01

The US Environmental Protection Agency (EPA) is required by the 1990 CAAA to promulgate rules for all ''major'' sources of any of these HAPs. According to the HAPs section of the new Title III, any stationary source emitting 10 tons per year (TPY) of one HAP or 25 TPY of a combination of HAPs will be considered and designated a major source. In contrast to the original National Emission Standards for Hazardous Air Pollutants (NESHAP), which were designed to protect public health to ''an ample margin of safety,'' the new Title III, in its first phase, will regulate by industrial category those sources emitting HAPs in excess of the 10/25-TPY threshold levels, regardless of health risks. The trace elements normally associated with coal mineral matter and the various compounds formed during coal combustion have the potential to produce hazardous air toxic emissions from coal-fired electric utilities. Under Title III, the EPA is required to perform certain studies, prior to any regulation of electric utilities; these studies are currently underway. Also, the US Department of Energy (DOE) maintains a vested interest in addressing those energy policy questions affecting electric utility generation, coal mining, and steel producing critical to this country's economic well-being, where balancing the costs to the producers and users of energy with the benefits of environmental protection to the workers and the general populace remains of significant concern

The role of coal in the US energy economy: Interfuel competition, environmental concerns, and the impact of utility restructuring

International Nuclear Information System (INIS)

Raschke, M.G.

1988-01-01

This paper briefly examines the role coal plays in the US energy economy and its competition with nuclear power, and then in greater detail the impact of environmental regulation, changes in utility regulation, and inter fuel competition on the future of coal. The US as the world's number two coal producer, shares many of the same problems and concerns as China, the world's number one coal producer. The use of coal in electric generation has been and will continue to be the only growth sector for the coal industry. The steel industry remains in permanent long-term decline. Forecasts vary, but there are indications that even in conservative forecasts, there is more down side risk than upside potential. Poor performance in the nuclear power sector can be expected to favorably impact coal consumption in the long term. Continued escalation of operating costs could erode any cost advantage that nuclear plants currently enjoy. However, environmental concerns could also escalate operating costs for coal fired plants. Also, concern over the greenhouse effect may lead policy makers to reexamine the nuclear option of inherently safe reactors. The greatest challenge to expanded use of coal comes from environmental concerns. Acid rain is a complex political, economic, and scientific issue. Clean coal technologies are seen by many as the answer to the threat posed by various forms of clean air legislation and regulation. Significant changes in the regulatory environment for electric and gas utilities and technological developments are likely in the 1990's to alter the nature of the electric generation industry

Development of coal-based technologies for Department of Defense Facilities. Semiannual technical progress report, March 28, 1997--September 27, 1997

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Miller, S.F.; Morrison, J.L. [and others

1998-01-06

The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of developing technologies which can potentially decrease DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Phase I was completed on November 1, 1995. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Emissions reductions investigations included performing pilot-scale air toxics (i.e., trace elements and volatile organic compounds) testing and evaluating a ceramic filtering device on the demonstration boiler. Also, a sodium bicarbonate duct injection system was installed on the demonstration boiler. An economic analysis was conducted which investigated the benefits of decreased dependence on imported oil by using new coal combustion technologies. Work related to coal preparation and utilization was primarily focused on preparing the final report. Work in Phase III focused on coal preparation studies, pilot-scale NO{sub x} reduction studies, economic analyses of coal use, and evaluation of deeply-cleaned coal as boiler fuel. Coal preparation studies were focused on continuing activities on particle size control, physical separations, and surface-based separation processes. The evaluation of deeply-cleaned coal as boiler fuel included receiving three cleaned coals from Cyprus-Amax.

A collaborative project on the effects of coal quality on NO{sub x} emissions and carbon burnout in pulverised coal-fired utility boilers

Energy Technology Data Exchange (ETDEWEB)

Tilley, H.A.; O`Connor, M.; Stephenson, P.L.; Whitehouse, M.; Richards, D.G.; Hesselmann, G.; MacPhail, J.; Lockwood, F.C.; Williamson, J.; Williams, A.; Pourkashanian, M. [ETSU, Harwell (United Kingdom)

1998-12-01

This paper describes a UK Department of Trade and Industry-supported collaborative project entitled `The Effects of Coal Quality on Emission of Oxides of Nitrogen (NO{sub x}) and Carbon Burnout in Pulverised Coal-fired Utility Boilers`. The project involved extensive collaboration between the UK power generators, boiler and burner manufacturers and research groups in both industry and academia, together with several of the world`s leading computational fluid dynamics (CFD) `software houses`. The prime objectives of the project were to assess the relationship between NO{sub x} emissions and carbon burnout and to develop and validate predictive tools for assessing coals. Experimental work was carried out on various laboratory-scale apparatus and on single burner test facilities ranging from 160 kW{sub th} to 40 MW{sub th} in size and measurements were obtained from full-scale 500 MW{sub e} utility boiler trials. This data and basic coal data were then used to develop mathematical models to predict full-scale boiler performance with respect to NO{sub x} emissions and carbon-in-ash. Results showed good correlations for NO{sub x} and carbon burnout when comparing data from full-scale and large-scale rig trials. Laboratory-scale tests were found to be useful but the influence of burner aerodynamics was more difficult to quantify. Modelling showed that predicted NO{sub x} emissions were encouragingly close to measured emissions but predicting carbon burnout was less successful. 24 refs., 4 figs., 6 tabs.

Proceedings of the 2nd symposium on valves for coal conversion and utilization

Energy Technology Data Exchange (ETDEWEB)

Maxfield, D.A. (ed.)

1981-01-01

The 2nd symposium on valves for coal conversion and utilization was held October 15 to 17, 1980. It was sponsored by the US Department of Energy, Morgantown Energy Technology Center, in cooperation with the Valve Manufacturers Association. Seventeen papers have been entered individually into EDB and ERA. (LTN)

Achievement report for fiscal 1984 on Sunshine Program. Research on coal liquefaction reaction and the reforming and utilization of products; 1984 nendo sekitan no ekika hanno to seiseibutsu no kaishitsu riyo no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

Upon the development into a single law of the three liquefaction related laws, studies are started on coal liquefaction reaction and the reforming and utilization of the products. In the research on coal liquefaction reaction, the solvent ratio, change in reaction time, and change in liquefaction product constitution in case of repeated circulation of the solvent are tracked, and their relations with the liquefaction rate and yield are studied, these efforts involving the Taiheiyo coal, Yallourn coal, and the Miike coal. The Taiheiyo coal is subjected to a short-duration liquefaction reaction test. In the research on product reforming, the medium-gravity fraction from coal liquefaction is subjected to hydrogenation, and the effect of the reaction conditions on the properties and constitution of the thus-treated oil are studied. An SRC (solvent refined coal) solution of the Taiheiyo coal is subjected to hydrogenation in the presence of a Ni-Mo catalyst, and the SRC cracking rate and product properties are compared with those obtained from another solution treated with a Co-Mo catalyst. In the research on product utilization, the medium-gravity fraction from coal liquefaction is subjected to hydrogenation under three sets of different reaction conditions in the presence of a Ni-Mo/Al{sub 2}O{sub 3} based catalyst. In this process, specimens are prepared by mixing the original oil, its hydrogenated product, and a petroleum-based light oil, and a study is made about the usability of the specimens and their mixtures with petroleum-based heater oil as light oil or heater oil. (NEDO)

Prediction method of unburnt carbon for coal fired utility boiler using image processing technique of combustion flame

International Nuclear Information System (INIS)

Shimoda, M.; Sugano, A.; Kimura, T.; Watanabe, Y.; Ishiyama, K.

1990-01-01

This paper reports on a method predicting unburnt carbon in a coal fired utility boiler developed using an image processing technique. The method consists of an image processing unit and a furnace model unit. temperature distribution of combustion flames can be obtained through the former unit. The later calculates dynamics of the carbon reduction from the burner stages to the furnace outlet using coal feed rate, air flow rate, chemical and ash content of coal. An experimental study shows that the prediction error of the unburnt carbon can be reduced to 10%

Mercury in coal and the impact of coal quality on mercury emissions from combustion systems

International Nuclear Information System (INIS)

Kolker, Allan; Senior, Constance L.; Quick, Jeffrey C.

2006-01-01

The proportion of Hg in coal feedstock that is emitted by stack gases of utility power stations is a complex function of coal chemistry and properties, combustion conditions, and the positioning and type of air pollution control devices employed. Mercury in bituminous coal is found primarily within Fe-sulfides, whereas lower rank coal tends to have a greater proportion of organic-bound Hg. Preparation of bituminous coal to reduce S generally reduces input Hg relative to in-ground concentrations, but the amount of this reduction varies according to the fraction of Hg in sulfides and the efficiency of sulfide removal. The mode of occurrence of Hg in coal does not directly affect the speciation of Hg in the combustion flue gas. However, other constituents in the coal, notably Cl and S, and the combustion characteristics of the coal, influence the species of Hg that are formed in the flue gas and enter air pollution control devices. The formation of gaseous oxidized Hg or particulate-bound Hg occurs post-combustion; these forms of Hg can be in part captured in the air pollution control devices that exist on coal-fired boilers, without modification. For a given coal type, the capture efficiency of Hg by pollution control systems varies according to type of device and the conditions of its deployment. For bituminous coal, on average, more than 60% of Hg in flue gas is captured by fabric filter (FF) and flue-gas desulfurization (FGD) systems. Key variables affecting performance for Hg control include Cl and S content of the coal, the positioning (hot side vs. cold side) of the system, and the amount of unburned C in coal ash. Knowledge of coal quality parameters and their effect on the performance of air pollution control devices allows optimization of Hg capture co-benefit

A STUDY ON THE GRINDABILITY OF SERBIAN COALS

Directory of Open Access Journals (Sweden)

Dragoslava D Stojiljković

2011-01-01

Full Text Available Thermal power plants in the Republic of Serbia are making considerable efforts and even more considerable investments, not only to maintain electricity production at maximum design levels, but even to additionally increase the power output of existing generating units. Capacities of mills used in pulverized coal preparation are identified as one of the main constraints to achieving maximum mill plant capacity, while coal grindability is seen as one of the factors that directly affect capacities of the coal mills utilized in thermal power plants. The paper presents results of experimental investigation conducted for the purpose of determining Hardgrove grindability index of coal. The investigation was conducted in accordance with ISO 5074 and included analysis of approximately 70 coal samples taken from the open pit mine of Kolubara coal basin. Research results obtained indicate that coal rich in mineral matter and thus, of lower heating value is characterized by higher grindability index. Therefore, analyses presented in the paper suggest that characteristics of solid fuels analyzed in the research investigation conducted are such that the use coals less rich in mineral matter i. e. coals characterized by lower grindability index will cause coal mills to operate at reduced capacity. This fact should be taken into account when considering a potential for electricity production increase.

Problems in modernization of automation systems at coal preparation plants

Science.gov (United States)

Myshlyaev, L. P.; Lyakhovets, M. V.; Venger, K. G.; Leontiev, I. A.; Makarov, G. V.; Salamatin, A. S.

2018-05-01

The factors influencing the process of modernization (reconstruction) of the automation systems at coal preparation plants are described. Problems such as heterogeneity of existing and developed systems, planning of reconstruction of a technological complex without taking into account modernization of automated systems, commissioning without stopping the existing technological complex, as well as problems of conducting procurement procedures are discussed. The option of stage-by-stage start-up and adjustment works in the conditions of modernization of systems without long stops of the process equipment is offered.

Use of continuous mercury monitors at coal-fired utilities

Energy Technology Data Exchange (ETDEWEB)

Laudal, Dennis L.; Thompson, Jeffrey S.; Pavlish, John H. [Energy and Environmental Research Center, PO Box 9018, Grand Forks, ND 58202-9018 (United States); Brickett, Lynn A. [U.S. Department of Energy National Energy Technology Laboratory, PO Box 10940 MS 922-273C, Pittsburgh, PA 15236-0940 (United States); Chu, Paul [EPRI, 3412 Hillview Avenue, PO Box 10412, Palo Alto, CA 94303 (United States)

2004-06-15

In December 2000, the U.S. Environmental Protection Agency (EPA) published a notice of its determination that regulation of coal-fired utilities for mercury is appropriate and necessary as part of the hazardous air pollutant emission regulation for electric utility steam-generating units. To aid in the determination of mercury emissions from these sources, on-line mercury semicontinuous emission monitors (Hg SCEMs) have been developed and tested in recent years. Although Hg SCEMs have shown promise during these previous tests, rigorous field or long-term testing has not been done. In the past year, commercially available and prototype Hg SCEMs have been used by the Energy and Environmental Research Center (EERC) and others at several power plants. As part of the EERC work, Hg SCEMs were operated at a range of conditions and locations. In addition, the Hg SCEMs were operated for up to 1 month. The use of Hg SCEMs at these plants allowed for near-real-time data to be collected under changing plant conditions, as well as during normal ranges of operating conditions. Mercury emission data were obtained from different plants with different configurations. The plant configurations incorporated various pollution control technologies, including selective catalytic reduction (SCR), selective noncatalytic reduction, ammonium sulfate injection for flue gas conditioning, and flue gas desulfurization (FGD). The particulate control devices included electrostatic precipitators (ESPs), a fabric filter (FF), and a venturi scrubber. The testing at these sites included the operation of Hg SCEMs before and after particulate control devices, in wet and dry stack conditions, and at high temperatures (343 C). The results from these field measurements have provided data that have been evaluated to determine the reliability, variability, biases, and overall capability of Hg SCEMs for monitoring mercury at coal-fired utilities. Even under the best conditions, operation of Hg SCEMs is by no

Fiscal 2000 survey report on project for promoting international cooperation. Survey on coal utilization in APEC region (Coal note); 2000 nendo kokusai kyoryoku suishin jigyo chosa hokokusho. APEC iki nai ni okeru sekitan riyo jokyo tou chosa (Koru note)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of contributing to the infrastructure for promoting clean coal technology (CCT), there were compiled as the 'coal note' various kinds of coal-related information in China, Indonesia, Philippine, Thailand and Vietnam among APEC countries. Concerning China, for example, economic growth and energy supply/demand in the category of the energy outline were described in detail; as were the guiding principle. individual guidance plan, and specific energy policy of the 10th five year plan, in the category of the energy policy; coal deposits, geological summary, coal quality in each coal forming period, and the status quo of development, in the category of the coal mines and development; coal supply/demand, production, consumption, and export, in the category of the present status of the coal industry; producers, sales, quality of product coal, distribution, and price, in the category of the domestic supply; present state of environmental problems relating to coal, and environmental measures intended for coal, in the category of the coal-related environmental issues; and development, production, coal cleaning, quality control, safety control, and utilization (combustion, liquefaction and gasification), in the category of coal utilization technology, respectively. (NEDO)

The occurrence of potentially hazardous trace elements in five Highveld coals, South Africa

Energy Technology Data Exchange (ETDEWEB)

Wagner, Nicola J.; Hlatshwayo, Bafana [Sasol Technology Research and Development, P.O. Box 1, Sasolburg, 1947 (South Africa)

2005-08-19

Permian coals of the southern hemisphere are generally considered to contain lower concentrations of sulfides, halogens, and trace elements when compared to northern hemisphere Carboniferous coals. Few studies have considered the trace element content in South African coals, and little or no work has been published for Highveld coals. Of the nineteen coal fields in South Africa, the Highveld coal field is one of the nine currently producing, and is second largest in terms of production. Five run of mine samples and a high ash middlings product from the Number 4 Lower seam were analyzed, totaling six sample sets. Fourteen trace elements (As, Cd, Co, Cr, Cu, Hg, Mn, Mo, Ni, Pb, Sb, Se, V, and Zn) were selected for this study based on the global perception that these elements may be hazardous to human health and/or the environment when they are released during coal utilization. Several sample preparation techniques were tested using certified reference materials (SARMs 18, 19 and 20) to determine the most repeatable technique for these coals. The samples were analyzed by ICP-AES and CVAA (Hg only). Microwave digestion proved to be generally unreliable despite the utilization of several different methods. A slurry direct injection method into the ICP-AES provided good correlations with the reference material, but requires further development to enhance the confidence level in this relatively unexplored technique. Samples prepared based on three ASTM standards for the determination of trace elements in coal provided repeatable results in most instances, and were the preparation methods utilized for the Highveld coals. The trace element values determined for the Highveld coals are generally in good agreement with values available in literature for South African coals, with the exception of Hg, Mn and Cr. Hg values reported here are lower, Cr and Mn higher. Results generally agree well with analyses on the same samples conducted by the United States Geological Survey

Clean coal technologies in Japan: technological innovation in the coal industry

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-12-15

This brochure reviews the history clean coal technologies (CCT) in Japan and systematically describes the present state of CCT insofar. The brochure contains three parts. Part 1. CCT classifications; Part 2. CCT overview; and Part 3. Future outlook for CCT. The main section is part 2 which includes 1) technologies for coal resources development; 2) coal-fired power generation technologies - combustion technologies and gasification technologies; 3) iron making and general industry technologies; 4) multi-purpose coal utilization technologies - liquefaction technologies, pyrolysis technologies, powdering, fluidization, and co-utilisation technologies, and de-ashing and reforming technologies; 5) Environmental protection technologies - CO{sub 2} recovery technologies; flue gas treatment and gas cleaning technologies, and technologies to effectively use coal has; 6) basic technologies for advanced coal utilization; and 7) co-production systems.

Cofiring of rice straw and coal in a coal-fired utility boiler: thermodynamic analysis

Energy Technology Data Exchange (ETDEWEB)

Miyake, Raphael Guardini; Bazzo, Edson [Federal University of Santa Catarina (UFSC), Florianopolis, SC (Brazil). Dept. of Mechanical Engineering], Emails: miyake@labcet.ufsc.br, ebazzo@emc.ufsc.br; Bzuneck, Marcelo [Tractebel Energia, Capivari de Baixo, SC (Brazil)], E-mail: marcelob@tractebelenergia.com.br

2010-07-01

Cofiring combustion of biomass and coal is a near-term, low cost alternative for reduction fossil greenhouse gas emissions in coal fired power plants. Recent reviews identified over 288 applications in over 16 countries with promising results for different coal and biomass combinations. In Brazil, there is no previous experience of cofiring biomass and coal, resulting in new challenges to fuel handling and boiler operation. A first experience is now proposed into an existing coal power plant, using rice straw as biomass fuel. A thermodynamic model was developed in order to predict operating and emissions data, which should be used in cofiring system design. For 10% of biomass input, the total CO{sub 2} emission is expected to slightly increase. However, considering only the coal CO{sub 2} emission, it is expected to decrease in about 10%. Also, the corresponding SO{sub 2} emission decreases in about 8%. (author)

(Pittsburgh Energy Technology Center): Quarterly technical progress report for the period ending June 30, 1987. [Advanced Coal Research and Technology Development Programs

Energy Technology Data Exchange (ETDEWEB)

None

1988-02-01

Research programs on coal and coal liquefaction are presented. Topics discussed are: coal science, combustion, kinetics, surface science; advanced technology projects in liquefaction; two stage liquefaction and direct liquefaction; catalysts of liquefaction; Fischer-Tropsch synthesis and thermodynamics; alternative fuels utilization; coal preparation; biodegradation; advanced combustion technology; flue gas cleanup; environmental coordination, and technology transfer. Individual projects are processed separately for the data base. (CBS)

Understanding the effects of sulfur on mercury capture from coal-fired utility flue gases

Energy Technology Data Exchange (ETDEWEB)

Morris, E.A.; Morita, K.; Jia, C.Q. [University of Toronto, Toronto, ON (Canada)

2010-07-01

Coal combustion continues to be a major source of energy throughout the world and is the leading contributor to anthropogenic mercury emissions. Effective control of these emissions requires a good understanding of how other flue gas constituents such as sulfur dioxide (SO{sub 2}) and sulfur trioxide (SO{sub 3}) may interfere in the removal process. Most of the current literature suggests that SO{sub 2} hinders elemental mercury (Hg{sup 0}) oxidation by scavenging oxidizing species such as chlorine (Cl2) and reduces the overall efficiency of mercury capture, while there is evidence to suggest that SO{sub 2} with oxygen (O{sub 2}) enhances Hg{sup 0} oxidation by promoting Cl2 formation below 100{sup o}C. However, studies in which SO{sub 2} was shown to have a positive correlation with Hg{sup 0} oxidation in full-scale utilities indicate that these interactions may be heavily dependent on operating conditions, particularly chlorine content of the coal and temperature. While bench-scale studies explicitly targeting SO{sub 3} are scarce, the general consensus among full-scale coal-fired utilities is that its presence in flue gas has a strong negative correlation with mercury capture efficiency. The exact reason behind this observed correlation is not completely clear, however. While SO{sub 3} is an inevitable product of SO{sub 2} oxidation by O{sub 2}, a reaction that hinders Hg{sup 0} oxidation, it readily reacts with water vapor, forms sulfuric acid (H{sub 2 }SO{sub 4}) at the surface of carbon, and physically blocks active sites of carbon. On the other hand, H{sub 2}SO{sub 4} on carbon surfaces may increase mercury capacity either through the creation of oxidation sites on the carbon surface or through a direct reaction of mercury with the acid. However, neither of these beneficial impacts is expected to be of practical significance for an activated carbon injection system in a real coal-fired utility flue gas.

Reactivity of mechanical activated coals for special utilization

Energy Technology Data Exchange (ETDEWEB)

Turcaniova, L.; Kadarova, J.; Imrich, P.; Liptaj, T.; Vidlar, J.; Vasek, J.; Foldyna, F.; Sitek, J.; Balaz, P. [Slovak Academy of Science, Kosice (Slovakia). Inst. of Geotechnology

2004-09-01

The paper presents the coal activation effect as disintegration in the nano-submicron range and destruction carbon structure. The Slovak brown coal activated in planetary mill is characterised by destruction of organic structure of coal. The biggest activation effect connected with the destruction of C-C bonds of sp{sup 3} carbons has been confirmed by {sup 13}C NMR spectroscopy in the chemical structure of humic acids extracted from the coal sample activated for a period of 60 min. The specific surface of humic acids is much smaller then that of mechanically activated sample from which they were extracted. The black Czech coal was activated by two stage disintegration. In the first stage of mechanochemical activation using Grinding Aqueous Caustic Leaching, GACL method, a fine dispersed semiproduct is formed with the size of particles from 2.5 to 9000 nm. The additional disintegration using water jet increases the effect of disintegration in the submicron area of the coal product. The volume distribution maximum achieves in this stage about 60 wt% of 750 nm grains.

1982 Australian coal conference papers

Energy Technology Data Exchange (ETDEWEB)

1982-01-01

This third Australian coal conference included papers discussing the market for coal, finance and investment, use of computers, mining, coal research, coal preparation and waste disposal, marketing and trade, and the transport of coal. All papers have been individually abstracted.

Influence of coal batch preparation on the quality of metallurgical соkе

Directory of Open Access Journals (Sweden)

Катерина Олегівна Шмельцер

2015-10-01

Full Text Available To study the influence of coal batch properties on coke strength we have considered the quality of the coke produced at the plant in Krivoy Rog from 2008 till 2012. Such factors as the large number of coal suppliers, imprecise selection of the optimal degree of batch crushing result in the decline in coke quality, the batch density and contents of the lean class (<0,5 mm are not optimum; poor blending of the batch after crushing; increased moisture and ash content of the coking batch; and extreme fluctuation in the coal and batch characteristics. It was found that high humidity of coal batch and its large fluctuations has most profound effect on the mechanical properties of coke. Under deteriorating resource base the quality of the coking batch preparation is important, To have batch of proper quality the following key aspects must be taken into account: the batch must be crushed to an optimum degree that will result in leaning components decrease and increased contents of vitrivite in it which improves the sinterability and coking, and hence the quality of coke; the degree of mixing of the coking batch in all indices must be up to 98-99%, for uneven distribution in the coal chamber worsens the quality of coke

Removal of phenol by powdered activated carbon prepared from coal gasification tar residue.

Science.gov (United States)

Wang, Xiong-Lei; Shen, Jun; Niu, Yan-Xia; Wang, Yu-Gao; Liu, Gang; Sheng, Qing-Tao

2018-03-01

Coal gasification tar residue (CGTR) is a kind of environmentally hazardous byproduct generated in fixed-bed coal gasification process. The CGTR extracted by ethyl acetate was used to prepare powdered activated carbon (PAC), which is applied later for adsorption of phenol. The results showed that the PAC prepared under optimum conditions had enormous mesoporous structure, and the iodine number reached 2030.11 mg/g, with a specific surface area of 1981 m 2 /g and a total pore volume of 0.92 ml/g. Especially, without loading other substances, the PAC, having a strong magnetism, can be easily separated after it adsorbs phenol. The adsorption of phenol by PAC was studied as functions of contact time, temperature, PAC dosage, solution concentration and pH. The results showed a fast adsorption speed and a high adsorption capacity of PAC. The adsorption process was exothermic and conformed to the Freundlich models. The adsorption kinetics fitted better to the pseudo-second-order model. These results show that CGTR can be used as a potential adsorbent of phenols in wastewater.

Energy-, environmental and economic evaluation of energy crops utilization

International Nuclear Information System (INIS)

1994-06-01

This preliminary project is prepared in order to clarify the economic possibilities and rentability of energy crops. Examples of energy crop resource potential, environmental and economic consequences are calculated on the basis of existing data. Utilization of annual and perennial crops is evaluated with regard to the usual following of agricultural areas, and to the traditional power generation in a coal-fueled plant. Two technological options are discussed: one based on energy crop fuels supplementing the conventional coal fuel, and the other based on a separate biomass-fueled boiler, connected to the conventional coal-fueled unit. Implementation of the main project,following the preliminary one will permit to estimate the future prospects and strategies of energy crop utilization as a profitable energy resource. (EG)

Utilization potentiality of coal as a reductant for the production of sponge iron. [5 refs

Energy Technology Data Exchange (ETDEWEB)

Mishra, H P

1976-10-01

With the ambitious plan of the Government of India to produce about 70 million tonnes of steel per annum towards the end of the century, the requirement of coal would be enormous. This calls for judicious planning and conservation of coal. Modern trend in steel plant practice is to use blast furnaces of capacity 10,000 to 12,000 t/day requiring superior quality coke of low ash content which will become scarce. Concerted efforts should be made to by-pass blast furnace technique by adopting direct reduction for the production of metallized iron ore, that is sponge iron, and using this as feed stock in electric furnaces. Experience has shown that the use of sponge iron as feed stock for electric arc furnaces instead of the scrap available from various fabrication and steel works results in better production of alloy steels. The use of non-coking coal as reductant for production of sponge iron will help conserve coking coal for bigger steel plants. In the solid state reduction process the technological design of the sponge iron plant has to be tailored to the type of feed stock to be used, particularly iron ore and coal. In India, non-coking coal is available at close proximity to the iron ore mines containing high grade iron ore. Planning for sponge iron, utilizing large reserves of non-coking coal as feed stock therefore has considerable potentiality. India has vast reserves of high grade iron ore and comparatively meager amount of coking coal. This calls for planning for sponge iron using non-coking coal as feed stock.

Hydrogen production from coal using a nuclear heat source

Science.gov (United States)

Quade, R. N.

1976-01-01

A strong candidate for hydrogen production in the intermediate time frame of 1985 to 1995 is a coal-based process using a high-temperature gas-cooled reactor (HTGR) as a heat source. Expected process efficiencies in the range of 60 to 70% are considerably higher than all other hydrogen production processes except steam reforming of a natural gas. The process involves the preparation of a coal liquid, hydrogasification of that liquid, and steam reforming of the resulting gaseous or light liquid product. A study showing process efficiency and cost of hydrogen vs nuclear reactor core outlet temperature has been completed, and shows diminishing returns at process temperatures above about 1500 F. A possible scenario combining the relatively abundant and low-cost Western coal deposits with the Gulf Coast hydrogen users is presented which provides high-energy density transportation utilizing coal liquids and uranium.

Sustainable development with clean coal

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-08-01

This paper discusses the opportunities available with clean coal technologies. Applications include new power plants, retrofitting and repowering of existing power plants, steelmaking, cement making, paper manufacturing, cogeneration facilities, and district heating plants. An appendix describes the clean coal technologies. These include coal preparation (physical cleaning, low-rank upgrading, bituminous coal preparation); combustion technologies (fluidized-bed combustion and NOx control); post-combustion cleaning (particulate control, sulfur dioxide control, nitrogen oxide control); and conversion with the integrated gasification combined cycle.

Thar coal exploration : a radical view

International Nuclear Information System (INIS)

Khan, N.A.

1996-01-01

Pakistan needs a manpower intensive technology to utilize its immense human resource. This human resource, however, has low literacy rate and thus lower skills and therefore there is a requirement of visualizing an employment technique compatible with the human resource. The vast coal deposits at Thar Coal Field provide an opportunity for development of low cost coal mining technique utilizing this manpower. Our history is filled with examples of effective utilization of human resources in the recent past. 300 years ago a few Muslim Emperors of the subcontinents constructed 40 meters deep wells, by utilizing human power only, to reach drinking water deep down, now in 2000 AD, can we go down 120 meters to dig the coal in Thar Coal Field by utilizing much enlarged manpower? (author)

THE DEVELOPMENT OF COAL-BASED TECHNOLOGIES FOR DEPARTMENT OF DEFENSE FACILITIES

Energy Technology Data Exchange (ETDEWEB)

Bruce G. Miller; Sharon Falcone Miller; Sarma V. Pisupati; Chunshan Song; Ronald S. Wasco; Ronald T. Wincek; Xiaochun Xu; Alan W. Scaroni; Richard Hogg; Subhash Chander; M. Thaddeus Ityokumbul; Mark S. Klima; Peter T. Luckie; Adam Rose; Richard L. Gordon; Jeffrey Lazo; A. Michael Schaal

2004-01-30

The third phase of a three-phase project investigating the development of coal-based technologies for US Department of Defense (DOD) facilities was completed. The objectives of the project were to: decrease DOD's dependence on foreign oil and increase its use of coal; promote public and private sector deployment of technologies for utilizing coal-based fuels in oil-designed combustion equipment; and provide a continuing environment for research and development of coal-based fuel technologies for small-scale applications at a time when market conditions in the US are not favorable for the introduction of coal-fired equipment in the commercial and industrial capacity ranges. The Phase III activities were focused on evaluating deeply-cleaned coals as fuels for industrial boilers and investigating emissions control strategies for providing ultra-low emissions when firing coal-based fuels. This was addressed by performing coal beneficiation and preparation studies, and bench- to demonstration-scale emissions reduction studies. In addition, economic studies were conducted focused on determining cost and market penetration, selection of incentives, and regional economic impacts of coal-based technologies.

Co-firing straw and coal in a 150-MWe utility boiler: in situ measurements

DEFF Research Database (Denmark)

Hansen, P. F.B.; Andersen, Karin Hedebo; Wieck-Hansen, K.

1998-01-01

A 2-year demonstration program is carried out by the Danish utility I/S Midtkraft at a 150-MWe PF-boiler unit reconstructed for co-firing straw and coal. As a part of the demonstration program, a comprehensive in situ measurement campaign was conducted during the spring of 1996 in collaboration...... with the Technical University of Denmark. Six sample positions have been established between the upper part of the furnace and the economizer. The campaign included in situ sampling of deposits on water/air-cooled probes, sampling of fly ash, flue gas and gas phase alkali metal compounds, and aerosols as well...... deposition propensities and high temperature corrosion during co-combustion of straw and coal in PF-boilers. Danish full scale results from co-firing straw and coal, the test facility and test program, and the potential theoretical support from the Technical University of Denmark are presented in this paper...

Utilizing coal remaining resources and post-mining land use planning based on GIS-based optimization method : study case at PT Adaro coal mine in South Kalimantan

Directory of Open Access Journals (Sweden)

Mohamad Anis

2017-06-01

Full Text Available Coal mining activities may cause a series of environmental and socio-economic issues in communities around the mining area. Mining can become an obstacle to environmental sustainability and a major hidden danger to the security of the local ecology. Therefore, the coal mining industry should follow some specific principles and factors in achieving sustainable development. These factors include geological conditions, land use, mining technology, environmental sustainability policies and government regulations, socio-economic factors, as well as sustainability optimization for post-mining land use. Resources of the remains of the coal which is defined as the last remaining condition of the resources and reserves of coal when the coal companies have already completed the life of the mine or the expiration of the licensing contract (in accordance with government permission. This research uses approch of knowledge-driven GIS based methods mainly Analytical Hierarchy Process (AHP and Fuzzy logic for utilizing coal remaining resources and post-mining land use planning. The mining area selected for this study belongs to a PKP2B (Work Agreement for Coal Mining company named Adaro Indonesia (PT Adaro. The result shows that geologically the existing formation is dominated by Coal Bearing Formation (Warukin Formation which allows the presence of remains coal resource potential after the lifetime of mine, and the suitability of rubber plantation for the optimization of land use in all mining sites and also in some disposal places in conservation areas and protected forests.

Environmental problems in Russian coal industry

International Nuclear Information System (INIS)

Kharchenko, V.; Oumnov, V.

1996-01-01

The state of the Russian coal industry is complicated both economically and environmentally. Most mines are unprofitable. Several coal mines are intended to be closed. So, under existing conditions, coal mines are unable to give much attention to environmental protection problems. At the same time, coal mining is one of the most polluting industries. The main trends in this industry's negative influence upon the environment are: land spoilage and immobilization to lay out open-pit mines and mineral waste dump areas and tailing piles as well as with industrial waste water runoff; atmospheric pollution with the air coming from underground and substances blown off from dumps, hydrogeological regime intervention in coal mining areas, etc. One way to solve environmental problems in coal mining is a more rational utilization of the accompanying natural coal resources. Such measures make it possible to obtain complementary profits not only at the expense of reducing environmental destruction but producing new kinds of goods or services as well. Examples of similar solutions are solid mineral wastes utilization, underground space utilization, coal gas utilization and other issues

Assessing coal burnout

Energy Technology Data Exchange (ETDEWEB)

Lowe, A. [Pacific Power, Sydney, NSW (Australia)

1999-11-01

Recent research has allowed a quantitative description of the basic process of burnout for pulverized coals to be made. The Cooperative Research Centre for Black Coal Utilization has built on this work to develop a coal combustion model which will allow plant engineers and coal company representatives to assess their coals for combustion performance. The paper describes the model and its validation and outlines how it is run. 2 figs.

Development of world coal reserves, their registration and their utilization

Energy Technology Data Exchange (ETDEWEB)

Bachmann, H

1979-10-01

This paper examines statistics on world coal production and world coal reserves with figures from 1860 to 1974 provided in tables and graphs. Eighty percent of the total world coal reserves (92% of world brown coal reserves) lie in the USA and USSR. The recent increase in total coal reserve estimates is due to exploration in western USA and in the USSR east of the Urals. Depth and thickness of the world's coal seams are shown in graphs and variations in coal quality are discussed. Problems associated with the anticipated substantial increase in coal production up to the year 2000 are considered. Encouraging higher coal production is the successful development of highly mechanized underground mining techniques and highly productive heavy surface mining equipment which allows excavation at increased depths. Surface mining is expected to make up 50% of total world mining operations in the near future. More complete deposit exploitation also contributes to higher coal production. Low international ship freight rates would facilitate future world coal trade. Obstacles are seen as: high, long term investments due to the fact that coal reserves lie far from populated and industrialized areas; opening new mines; transportation costs and infrastructure development.

DEMONSTRATION OF SORBENT INJECTION TECHNOLOGY ON A TANGENTIALLY COAL-FIRED UTILITY BOILER (YORKTOWN LIMB DEMONSTRATION)

Science.gov (United States)

The report summarizes activities conducted and results achieved in an EPA-sponsored program to demonstrate Limestone Injection Multistage Burner (LIMB) technology on a tangentially fired coal-burning utility boiler, Virginia Power's 180-MWe Yorktown Unit No. 2. his successfully d...

Chromatographic methods and techniques used in studies of coals, their progenitors and coal-derived materials

Energy Technology Data Exchange (ETDEWEB)

Zubkova, Valentina [Jan Kochanowski University of Humanities and Sciences, Institute of Chemistry, Kielce (Poland)

2011-03-15

The use of chromatography in studies of coals, their progenitors and coal-related products was reviewed. The specificity of the coal structure was discussed. The use of extraction in preparing study samples was discussed paying special attention to the occurrence of undesirable phenomena such as aggregation of coal derivate molecules, resulting from the formation of their dimers and trimers, and degradation of polar solvents at temperatures above 350 C. The following ways of fractionating samples of coal materials were considered: thermal, solvent, column with the use of preparative size exclusive chromatography and preparative thin layer chromatography as well as membrane separation. The use of chromatography coupled with experimental techniques such as mass spectrometry, infrared spectroscopy, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry and pyrolysis was analysed. (orig.)

Low-rank coal research, Task 5.1. Topical report, April 1986--December 1992

Energy Technology Data Exchange (ETDEWEB)

1993-02-01

This document is a topical progress report for Low-Rank Coal Research performed April 1986 - December 1992. Control Technology and Coal Preparation Research is described for Flue Gas Cleanup, Waste Management, Regional Energy Policy Program for the Northern Great Plains, and Hot-Gas Cleanup. Advanced Research and Technology Development was conducted on Turbine Combustion Phenomena, Combustion Inorganic Transformation (two sections), Liquefaction Reactivity of Low-Rank Coals, Gasification Ash and Slag Characterization, and Coal Science. Combustion Research is described for Atmospheric Fluidized-Bed Combustion, Beneficiation of Low-Rank Coals, Combustion Characterization of Low-Rank Fuels (completed 10/31/90), Diesel Utilization of Low-Rank Coals (completed 12/31/90), Produce and Characterize HWD (hot-water drying) Fuels for Heat Engine Applications (completed 10/31/90), Nitrous Oxide Emission, and Pressurized Fluidized-Bed Combustion. Liquefaction Research in Low-Rank Coal Direct Liquefaction is discussed. Gasification Research was conducted in Production of Hydrogen and By-Products from Coals and in Sulfur Forms in Coal.

Coal pump

Science.gov (United States)

Bonin, John H.; Meyer, John W.; Daniel, Jr., Arnold D.

1983-01-01

A device for pressurizing pulverized coal and circulating a carrier gas is disclosed. This device has utility in a coal gasification process and eliminates the need for a separate collection hopper and eliminates the separate compressor.

A bottom-up method to develop pollution abatement cost curves for coal-fired utility boilers

Science.gov (United States)

This paper illustrates a new method to create supply curves for pollution abatement using boiler-level data that explicitly accounts for technology costs and performance. The Coal Utility Environmental Cost (CUECost) model is used to estimate retrofit costs for five different NO...

Preparation of steel slag porous sound-absorbing material using coal powder as pore former.

Science.gov (United States)

Sun, Peng; Guo, Zhancheng

2015-10-01

The aim of the study was to prepare a porous sound-absorbing material using steel slag and fly ash as the main raw material, with coal powder and sodium silicate used as a pore former and binder respectively. The influence of the experimental conditions such as the ratio of fly ash, sintering temperature, sintering time, and porosity regulation on the performance of the porous sound-absorbing material was investigated. The results showed that the specimens prepared by this method had high sound absorption performance and good mechanical properties, and the noise reduction coefficient and compressive strength could reach 0.50 and 6.5MPa, respectively. The compressive strength increased when the dosage of fly ash and sintering temperature were raised. The noise reduction coefficient decreased with increasing ratio of fly ash and reducing pore former, and first increased and then decreased with the increase of sintering temperature and time. The optimum preparation conditions for the porous sound-absorbing material were a proportion of fly ash of 50% (wt.%), percentage of coal powder of 30% (wt.%), sintering temperature of 1130°C, and sintering time of 6.0hr, which were determined by analyzing the properties of the sound-absorbing material. Copyright © 2015. Published by Elsevier B.V.

Low-rank coal research. Final technical report, April 1, 1988--June 30, 1989, including quarterly report, April--June 1989

Energy Technology Data Exchange (ETDEWEB)

1989-12-31

This work is a compilation of reports on ongoing research at the University of North Dakota. Topics include: Control Technology and Coal Preparation Research (SO{sub x}/NO{sub x} control, waste management), Advanced Research and Technology Development (turbine combustion phenomena, combustion inorganic transformation, coal/char reactivity, liquefaction reactivity of low-rank coals, gasification ash and slag characterization, fine particulate emissions), Combustion Research (fluidized bed combustion, beneficiation of low-rank coals, combustion characterization of low-rank coal fuels, diesel utilization of low-rank coals), Liquefaction Research (low-rank coal direct liquefaction), and Gasification Research (hydrogen production from low-rank coals, advanced wastewater treatment, mild gasification, color and residual COD removal from Synfuel wastewaters, Great Plains Gasification Plant, gasifier optimization).

Opportunities for Decarbonizing Existing U.S. Coal-Fired Power Plants via CO2 Capture, Utilization and Storage.

Science.gov (United States)

Zhai, Haibo; Ou, Yang; Rubin, Edward S

2015-07-07

This study employs a power plant modeling tool to explore the feasibility of reducing unit-level emission rates of CO2 by 30% by retrofitting carbon capture, utilization, and storage (CCUS) to existing U.S. coal-fired electric generating units (EGUs). Our goal is to identify feasible EGUs and their key attributes. The results indicate that for about 60 gigawatts of the existing coal-fired capacity, the implementation of partial CO2 capture appears feasible, though its cost is highly dependent on the unit characteristics and fuel prices. Auxiliary gas-fired boilers can be employed to power a carbon capture process without significant increases in the cost of electricity generation. A complementary CO2 emission trading program can provide additional economic incentives for the deployment of CCS with 90% CO2 capture. Selling and utilizing the captured CO2 product for enhanced oil recovery can further accelerate CCUS deployment and also help reinforce a CO2 emission trading market. These efforts would allow existing coal-fired EGUs to continue to provide a significant share of the U.S. electricity demand.

Coal, energy and environment: Proceedings

International Nuclear Information System (INIS)

Mead, J.S.; Hawse, M.L.

1994-01-01

This international conference held in Czechoslovakia was a bold attempt to establish working relationships among scientists and engineers from three world areas: Taiwan, the United States of America, and Czechoslovakia. The magic words unifying this gathering were ''clean coal utilization.'' For the ten nationalities represented, the common elements were the clean use of coal as a domestic fuel and as a source of carbon, the efficient and clean use of coal in power generation, and other uses of coal in environmentally acceptable processes. These three world areas have serious environmental problems, differing in extent and nature, but sufficiently close to create a working community for discussions. Beyond this, Czechoslovakia is emerging from the isolation imposed by control from Moscow. The need for each of these nations to meet and know one another was imperative. The environmental problems in Czechoslovakia are extensive and deep-seated. These proceedings contain 63 papers grouped into the following sections: The research university and its relationship with accrediting associations, government and private industry; Recent advances in coal utilization research; New methods of mining and reclamation; Coal-derived waste disposal and utilization; New applications of coal and environmental technologies; Mineral and trace elements in coal; Human and environmental impacts of coal production and utilization in the Silesian/Moravian region; and The interrelationships between fossil energy use and environmental objectives. Most papers have been processed separately for inclusion on the data base

NO{sub x} controls for coal-fired utility boilers in East Central Europe

Energy Technology Data Exchange (ETDEWEB)

Eskinazi, D. [Electric Power Research Inst., Washington, DC (United States); Tavoulareas, E.S. [Energy Technologies Enterprises Corp., McLean, VA (United States)

1995-12-01

Increasing environmental pressures worldwide, including East Central Europe are placing greater emphasis on NO{sub x} emission controls in utility power plants. Western Europe, Japan and the U.S. have significant experience in applying NO{sub x} controls, especially in boilers firing hard coal. Some countries in Europe (i.e., Germany and Austria), have gained experience in applying NO{sub x} controls in boilers firing low-rank coal. This experience can be applied to East Central European countries in providing the basis for planning NO{sub x} control projects, suggesting cost-effective solutions, and providing lessons learned. However, while the experience is generally applicable to East Central European countries, differences in boiler design, operation and coal characteristics also need to be considered. This paper begins with a comparison of the NO{sub x} regulations, identifies the key NO{sub x} control technologies and the worldwide experience with them, and discusses the achievable NO{sub x} reduction, O&M impacts, and retrofit costs for each technology. Emphasis is placed on retrofit applications for existing boilers, because new coal-fired power plants are not expected to be built for the next 5-10 years. This paper also focuses on technologies with relatively low cost and operational simplicity: combustion system tuning/optimization. low-NO{sub x} burners (LNB), overfire air (OFA), selective non-catalytic reduction (SNCR), and reburning.

Utilization of coal ash/coal combustion products for mine reclamation

International Nuclear Information System (INIS)

Dolence, R.C.; Giovannitti, E.

1997-01-01

Society's demand for an inexpensive fuel, combined with ignorance of the long term impacts, has left numerous scars on the Pennsylvania landscape. There are over 250,000 acres of abandoned surface mines with dangerous highwalls and water filled pits. About 2,400 miles of streams do not meet water quality standards because of drainage from abandoned mines. There are uncounted households without an adequate water supply due to past mining practices. Mine fires and mine subsidence plague many Pennsylvania communities. The estimated cost to reclaim these past scars is over $15 billion. The beneficial use of coal ash in Pennsylvania for mine reclamation and mine drainage pollution abatement projects increased during the past ten years. The increase is primarily due to procedural and regulatory changes by the Department of Environmental Protection (DEP). Prior to 1986, DEP required a mining permit and a separate waste disposal permit for the use of coal ash in backfilling and reclaiming a surface mine site. In order to eliminate the dual permitting requirements and promote mine reclamation, procedural changes now allow a single permit which authorize both mining and the use of coal ash in reclaiming active and abandoned pits. The actual ash placement, however, must be conducted in accordance with the technical specifications in the solid waste regulations

Fiscal 1995 survey of the base arrangement promotion for foreign coal import. Investigation on the policy of coal demand stabilization using low grade coal; 1995 nendo kaigaitan yunyu kiban sokushin chosa. Teihin`itan riyo ni yoru sekitan jukyu anteika hosaku ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The paper investigated the trend of and the needs for low grade coal utilization and the seeds of low grade coal utilization technology and studied usability of low grade coal in the future. Importance of low grade coal utilization was described in consideration of features of the Asia/Pacific area in the world coal market, and the trend of production/utilization of low grade coal was examined mostly in countries holding main low grade coals in the Asia/Pacific area. The trend of the technical development contributing to the low grade coal utilization was studied to make it contribute to the extraction of technologies which are regarded as effective in the Asia/Pacific area. A study was made of applicability of the low grade coal utilization technology corresponding to the needs for low grade coal utilization, and at the same time, a study was made of the effect on the coal supply/demand in the Asia/Pacific area in case the low grade coal utilization is promoted helped by the study. Focusing on technical cooperation relating to clean coal technology, a study was conducted of the trend of international cooperation in Japan and various overseas countries and the trend of new cooperation in private sectors, and a discussion was made on how Japan should act toward promotion of low grade coal utilization. 12 figs., 91 tabs.

Coal Mines Security System

OpenAIRE

Ankita Guhe; Shruti Deshmukh; Bhagyashree Borekar; Apoorva Kailaswar; Milind E.Rane

2012-01-01

Geological circumstances of mine seem to be extremely complicated and there are many hidden troubles. Coal is wrongly lifted by the musclemen from coal stocks, coal washeries, coal transfer and loading points and also in the transport routes by malfunctioning the weighing of trucks. CIL —Coal India Ltd is under the control of mafia and a large number of irregularities can be contributed to coal mafia. An Intelligent Coal Mine Security System using data acquisition method utilizes sensor, auto...

Balance of natural radionuclides in the brown coal based power generation and harmlessness of the residues and side product utilization

International Nuclear Information System (INIS)

Schulz, Hartmut; Kunze, Christian; Hummrich, Holger

2017-01-01

During brown coal combustion a partial enrichment of natural radionuclides occurs in different residues. Residues and side product from brown coal based power generation are used in different ways, for example filter ashes and gypsum from flue gas desulfurization facilities are used in the construction materials fabrication and slags for road construction. Detailed measurement and accounting of radionuclides in the mass throughputs in coal combustion power plants have shown that the utilized gypsum and filter ashes are harmless in radiologic aspects.

Analysis of oxy-fuel combustion power cycle utilizing a pressurized coal combustor

OpenAIRE

Gazzino, Marco; Hong, Jongsup; Chaudhry, Gunaranjan; Brisson II, John G; Field, Randall; Ghoniem, Ahmed F

2009-01-01

Growing concerns over greenhouse gas emissions have driven extensive research into new power generation cycles that enable carbon dioxide capture and sequestration. In this regard, oxy-fuel combustion is a promising new technology in which fuels are burned in an environment of oxygen and recycled combustion gases. In this paper, an oxy-fuel combustion power cycle that utilizes a pressurized coal combustor is analyzed. We show that this approach recovers more thermal energy from the flue gases...

Manufacture of lightweight aggregates utilizing coal fly ash. Sekitan bai riyo ni yoru jinko keiryo kotsuzai seizo

Energy Technology Data Exchange (ETDEWEB)

Ishii, K [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1990-11-20

Processing of a large amount of coal ash is a serious problem in considering the locational conditions of coal firing power generation plants. 46% of the coal ash was effectively used in 1985, and the remaining 54% was disposed at landfills on land and sea. Positive promotion of the effective use of coal ash is the necessity. A production method for an artificial lightweight aggregate utilizing coal ash was established by a joint research. The history of the research and development of this artificial lightweight aggregate (brand name: FA-lIGHT), outline of the manufacturing facilities, physical properties and result of use are introduced. The lightweight aggregates are used not only for the construction of multistoried buildings but also used as most suitable aggregates for making lightweight large scale panels and concrete secondary products such as lightweight blocks. FA-LIGHT is most suitable for use in the production of concrete lightweight aggregates, and can be used for hydroponic agriculture and for the improvement of drainage of land. Spread of its use is expected. 5 figs., 5 tabs.

Issues and prospects for coal utilization in Zimbabwe's rural households

International Nuclear Information System (INIS)

Maya, R.S.

1990-01-01

The increasing shortage of traditional fuels in Zimbabwe has prompted government to consider seriously the use of coal in rural households. In this regard, both government and the privately owned coal industry have begun pilot projects in selected rural areas to initiate the introduction of coal stoves and coal fuels. These efforts by government and the coal industry need to be informed by knowledge of the financial and economic dimensions of coal diffusion to rural economies, the environmental implications of widespread coal use in rural households, and the general acceptability of coal as a fuel to households with a long tradition of free fuels. This paper summarizes the results of a study undertaken to provide such background information. Conducted over six months during 1988, the study included field surveys of four districts in Zimbabwe: Murewa, Shurugwi, Mberengwa, and Mazoe Citrus Estates. All but the Mazoe district are rural settings with severe shortages of fuelwood. Mazoe Citrus Estates is a semi-urban plantation community which has had over twenty years' experience with coal use in households under a company-sponsored programme which supplies both fuels and stoves free of charge

Quarterly coal report, January--March 1993

Energy Technology Data Exchange (ETDEWEB)

1993-08-20

The United States produced 242 million short tons of coal in the first quarter of 1993, a decrease of 6 percent (14 million short tons) from the amount produced during the first quarter of 1992. The decrease was due to a decline in production east of the Mississippi River. All major coal-producing States in this region had lower coal production levels led by West Virginia, which produced 5 million short tons less coal. The principal reasons for the overall drop in coal output compared to a year earlier were: A decrease in demand for US coal in foreign markets; a slower rate of producer/distributor stock build-up; and a drawn-down of electric utility coal stocks. Distribution of US coal in the first quarter of 1993 was 10 million short tons lower than in the first quarter of 1992, with 5 million short tons less distributed to both electric utilities and overseas markets. The average price of coal delivered to electric utilities during the first quarter of 1993 was $28.65 per short ton, the lowest value since the first quarter of 1980. Coal consumption in the first quarter of 1993 was 230 million short tons, 4 percent higher than in the first quarter of 1992, due primarily to a 5-percent increase in consumption at electric utility plants. Total consumer stocks, at 153 million short tons, and electric utility stocks, at 144 million short tons, were at their lowest quarterly level since the end of 1989. US. coal exports totaled 19 million short tons, 6 million short tons less than in the first quarter of 1992, and the lowest quarterly level since 1988. The decline was primarily due to a 1-million-short-ton drop in exports to each of the following destinations: Italy, France, Belgium and Luxembourg, and Canada.

Quarterly coal report, January--March 1993

International Nuclear Information System (INIS)

1993-01-01

The United States produced 242 million short tons of coal in the first quarter of 1993, a decrease of 6 percent (14 million short tons) from the amount produced during the first quarter of 1992. The decrease was due to a decline in production east of the Mississippi River. All major coal-producing States in this region had lower coal production levels led by West Virginia, which produced 5 million short tons less coal. The principal reasons for the overall drop in coal output compared to a year earlier were: A decrease in demand for US coal in foreign markets; a slower rate of producer/distributor stock build-up; and a drawn-down of electric utility coal stocks. Distribution of US coal in the first quarter of 1993 was 10 million short tons lower than in the first quarter of 1992, with 5 million short tons less distributed to both electric utilities and overseas markets. The average price of coal delivered to electric utilities during the first quarter of 1993 was $28.65 per short ton, the lowest value since the first quarter of 1980. Coal consumption in the first quarter of 1993 was 230 million short tons, 4 percent higher than in the first quarter of 1992, due primarily to a 5-percent increase in consumption at electric utility plants. Total consumer stocks, at 153 million short tons, and electric utility stocks, at 144 million short tons, were at their lowest quarterly level since the end of 1989. US. coal exports totaled 19 million short tons, 6 million short tons less than in the first quarter of 1992, and the lowest quarterly level since 1988. The decline was primarily due to a 1-million-short-ton drop in exports to each of the following destinations: Italy, France, Belgium and Luxembourg, and Canada

Catalytic technology in the energy/environment field. Utilization of catalyst in coal pyrolysis and gasification processes; Energy kankyo bun`ya ni okeru shokubai gijutsu. Sekitan no netsubunkai oyobi gas ka ni okeru shokubai no riyo

Energy Technology Data Exchange (ETDEWEB)

Otsuka, Y. [Tohoku University, Institute for Chemical Reaction Science (Japan)

1998-05-20

This review article focuses on the utilization of several catalysts during coal pyrolysis and gasification. In situ or off line catalytic upgrading of volatile matters during pyrolysis of low rank coals is carried out in pressurized H2 with different reactors to produce BTX (benzene, toluene and xylene). When NiSO4 and Ni(OH)2 are used in the hydropyrolysis of Australian brown coal using an entrained bed reactor with two separated reaction zones, BTX yield reaches 18-23%. MS-13X zeolite and USY zeolite mixed with Al2O3 are effective for producing BTX with powder-particle fluidized bed and two-stage reactors, respectively. Catalytic gasification is described from a standpoint of direct production of SNG(CH4) from coal and steam. When K2CO3 and Ni are compared for this purpose, Ni catalyst is more suitable at low temperatures of 500-600degC, where CH4 formation is thermodynamically favorable. Fe and Ca catalysts can successfully be prepared from inexpensive raw materials and are rather active for steam gasification at {>=}700degC. The use of upgrading and gasification catalysts is discussed in terms of preparation, performance, life and recovery. 27 refs., 6 figs., 2 tabs.

Gc/ms analysis of coal tar composition produced from coal

African Journals Online (AJOL)

Coal pyrolysis is one of the significant approaches for the comprehensive utilization ... planigraphy-GC/MS; therefore a satisfactory analytical result obtained, which .... Among the aliphatic group of the coal tar, the proportion of alkene is larger ...

Venezuelan coal

International Nuclear Information System (INIS)

Vazquez, L.U.

1991-01-01

The existence of coal deposits in Venezuela has been known since the early nineteenth century, when the Naricual Mines were discovered in the State of Anzoategui Eastern Venezuela. Through the years the Venezuelan coal business had its ups and downs, but it was not until 1988 that we could properly say that our coal began to play a role in the international market. This paper reports that it is only now, in the nineties, that Venezuelan coal projects have come under a planning, promotional and developmental policy preparing the ground for the great projects Venezuela will have in the not-too-distant future

Development of coal-based technologies for Department of Defense Facilities. Semiannual technical progress report, September 28, 1996--March 27, 1997

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Miller, S.F.; Pisupati, S.V. [and others

1997-07-22

The U.S. Department of Defense (DOD), through an Interagency Agreement with the U.S. Department of Energy (DOE), has initiated a three-phase program with the Consortium for Coal-Water Slurry Fuel Technology, with the aim of developing technologies which can potentially decrease DOD`s reliance on imported oil by increasing its use of coal. The program is being conducted as a cooperative agreement between the Consortium and DOE. Work in Phase II focused on emissions reductions, coal beneficiation/preparation studies, and economic analyses of coal use. Work in Phase III focused on coal preparation studies, pilot-scale NO{sub x} reduction studies, economic analyses of coal use, and evaluation of deeply-cleaned coal as boiler fuel. Coal preparation studies were focused on continuing activities on particle size control, physical separations, surface-based separation processes, and dry processing. Preliminary pilot-scale NO{sub x} reduction catalyst tests were conducted when firing natural gas in Penn State`s down-fired combustor. This is the first step in the scale-up of bench-scale results obtained in Phase II to the demonstration boiler scale when firing coal. The economic study focused on community sensitivity to coal usage, regional/national economic impacts of new coal utilization technologies, and constructing a national energy portfolio. The evaluation of deeply-cleaned coal as boiler fuel included installing a ribbon mixer into Penn State`s micronized coal-water mixture circuit for reentraining filter cake. In addition, three cleaned coals were received from CQ Inc. and three cleaned coals were received from Cyprus-Amax.

Determination of sulfur in coal and ash slurry by high-resolution continuum source electrothermal molecular absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Nakadi, Flávio V.; Rosa, Lilian R.; Veiga, Márcia A.M.S. da, E-mail: mamsveiga@ffclrp.usp.br

2013-10-01

We propose a procedure for the determination of sulfur in coal slurries by high resolution continuum source electrothermal molecular absorption spectrometry. The slurry, whose concentration is 1 mg mL{sup −1}, was prepared by mixing 50 mg of the sample with 5% v/v nitric acid and 0.04% m/v Triton X-100 and was homogenized manually. It sustained good stability. The determination was performed via CS molecular absorption at 257.592 nm, and the optimized vaporization temperature was 2500 °C. The accuracy of the method was ensured by analysis of certified reference materials SRM 1632b (trace elements in coal) and SRM 1633b (coal fly ash) from the National Institute of Standards and Technology, using external calibration with aqueous standards prepared in the same medium and used as slurry. We achieved good agreement with the certified reference materials within 95% confidence interval, LOD of 0.01% w/w, and RSD of 6%, which confirms the potential of the proposed method. - Highlights: • HR-CS ET MAS as a technique to determine sulfur in coal and ash • Utilization of (coal and coal fly ash) slurry as a sample preparation • Simple and fast method, which uses external calibration with aqueous standards without chemical modifier.

Research report of FY 1997 on the environmentally acceptable coal utilization system feasibility survey. Clean coal technology model project seminar held in Thailand; 1997 nendo seika hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa (Tai ni okeru clean coal technology model jigyo seminar no kaisai)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

To reduce SOx with coal utilization, the desulfurization seminar diffusing the demonstration project of simplified desulfurizer introduction was held at the site in Thailand. The purpose is to reduce the environmental pollutants and contribute to the effective utilization of energy with coal utilization in Thailand. Invitation letters were sent to users of coal and heavy oil boilers through the Department of Factories, Ministry of Industry, Thailand, to call participation in the seminar. Inspection of the desulfurizer introduced in the factory of Thai Union Paper Public was included in the seminar for diffusing the project. The inspection site is in the demonstration project site of simplified desulfurizer introduction. There were a lot of participants from Thai users and from Japan. The seminar included the presentations from NEDO, JETRO, FTI, and MOSTE, introduction of general technology for processes of ENAA desulfurizer, introduction of demonstration unit plan by IHI, and introduction of operation of demonstration unit by TUP. 31 figs., 6 tabs.

Clean coal technologies

International Nuclear Information System (INIS)

Aslanyan, G.S.

1993-01-01

According to the World Energy Council (WEC), at the beginning of the next century three main energy sources - coal, nuclear power and oil will have equal share in the world's total energy supply. This forecast is also valid for the USSR which possesses more than 40% of the world's coal resources and continuously increases its coal production (more than 700 million tons of coal are processed annually in the USSR). The stringent environmental regulations, coupled with the tendency to increase the use of coal are the reasons for developing different concepts for clean coal utilization. In this paper, the potential efficiency and environmental performance of different clean coal production cycles are considered, including technologies for coal clean-up at the pre-combustion stage, advanced clean combustion methods and flue gas cleaning systems. Integrated systems, such as combined gas-steam cycle and the pressurized fluidized bed boiler combined cycle, are also discussed. The Soviet National R and D program is studying new methods for coal utilization with high environmental performance. In this context, some basic research activities in the field of clean coal technology in the USSR are considered. Development of an efficient vortex combustor, a pressurized fluidized bed gasifier, advanced gas cleaning methods based on E-beam irradiation and plasma discharge, as well as new catalytic system, are are presented. In addition, implementation of technological innovations for retrofitting and re powering of existing power plants is discussed. (author)

Preparation of briquettes on the basis of desintegrated phyto-materials and the admixture of fine-grained coal and coke

Directory of Open Access Journals (Sweden)

Jakabský Štefan

2002-03-01

Full Text Available The contribution deals with the preparation of small-diameter briquettes on the basis of desintegrated phyto-materials and the admixture of coal and coke. The phyto-materials are classified as a dry biomass that can be, on the one hand, the wastes from wood-working industry,(sawdust, chips, bark, etc. or dried mass from the plant production and, on the other hand, the mass of quick-growing plants cultivated on special plantations. In present time this renewable energy resource attracts attention by its heating value ranging from 10 to 16 MJ.kg-1 (EkoWATT, 2001, a low ash content of 0.5 – 6.5 % and by a low sulphur content in a water free sample of 0.05 –0.12 %.As a phyto-material the spruce sawdusts having a grain size of –2 mm were used. The admixture of brown coal, hard coal and coke with a grain size of 0.040 mm was added to the sawdust and in such way prepared mixtures were subjected to briquetting with the aim to obtain small-diameter briquettes. The influence of admixtures amount on the density, and the suitable briquetting press have been studied. A saleability of briquettes on the basis of phyto-materials is conditioned by their density that must be higher than 1,000 kg.m-3. Thus, an adding of denser material with a relatively high calorific value would enable to attain the required density as well as to retain and/or to improve the main utility properties, i.e. calorific value and ash content.The adding evinces itself in an enhancement of briquetting press, but also density of obtained briquettes is often much higher that required by the market. It was showed that in the case of clear spruce sawdust the density of 1,059 kg.m-3 under the briquetting press of 250 MPa can be attained. According to other results, an admixture of brown coal is not very favourable because briquetting press exceeds the value of 300 MPa. As to hard coal adding, the presses under 250 MPa were achieved at the content of 25 – 30 %. The density of these

Predicted coal production trends in Kentucky: The results of available coal resources, coal quality demands, and regulatory factors

International Nuclear Information System (INIS)

Watson, W.D.

1993-01-01

Many factors affect the viability of regional coal production markets including (1) coal quality and recoverable tonnage, (2) coal mining cost, (3) the regional and time varying patterns of coal demand growth, (4) regulations and other institutional constraints that affect coal demand and utilization, and (5) the regional array of coal transport modes and rates. This analysis integrates these factors into an assessment of coal production prospects (separately) for eastern and western Kentucky coal producing counties for the decade of the 90's. The integration indicates that eastern Kentucky coal production will peak and begin to decline by the end of the decade whereas western Kentucky coal production will continue to grow. No single factor explains these trends. There is plenty of available minable coal. The combination of changes in environmental regulations, some increase in coal mining costs, and the mining-out of low sulfur reserves are the main factors that account for the production trends

Coal tar pitch. Interrelations between properties and utilization of coal tar pitch

Energy Technology Data Exchange (ETDEWEB)

Collin, G; Koehler, H [Ruetgerswerke A.G., Duisburg (Germany, F.R.)

1977-06-01

Coal tar pitch is won as a highly aromatic, thermoplastic residue by destillating coal tar. In this paper the structure as well as the chemical and physical data of this pitch are introduced. In addition to this the actual as well as possible applications are indicated. For example, the pitch can be used for the production of binders, e.g. for electrodes and road construction as well as in combination with plastics for the production of insulating material and corrosion protection material.

Coal sector model: Source data on coal for the energy and power evaluation program (ENPEP)

International Nuclear Information System (INIS)

Suwala, W.

1997-01-01

Coal is the major primary energy source in Poland and this circumstances requires that the data on coal supply for use in energy planning models should be prepared properly. Economic sectors' development depends on many factors which are usually considered in energy planning models. Thus, data on the development of such sectors as coal mining should be consistent with the economic assumptions made in the energy planning model. Otherwise, coal data could bias the results of the energy planning model. The coal mining and coal distribution models which have been developed at the Polish Academy of Sciences could provide proper coal data of use in ENPEP and other energy planning models. The coal mining model optimizes the most important decisions related to coal productions, such as coal mines development, retirement of non-profitable mines, and construction of new mines. The model uses basic data forecasts of coal mine costs and coal production. Other factors such as demand for coal, world coal prices, etc., are parameters which constitute constraints and requirements for the coal mining development. The output of the model is the amount of coal produced and supply curves for different coal types. Such data are necessary for the coal distribution model and could also be used by ENPEP. This paper describes the model, its structure and how the results of the model could serve as coal-related data for ENPEP. Improvement of some input data forms of the BALANCE module of ENPEP are also suggested in order to facilitate data preparation. (author). 7 figs

Coal sector model: Source data on coal for the energy and power evaluation program (ENPEP)

Energy Technology Data Exchange (ETDEWEB)

Suwala, W [Mineral and Energy Economy Research Centre, Polish Academy of Sciences, Cracow (Poland)

1997-09-01

Coal is the major primary energy source in Poland and this circumstances requires that the data on coal supply for use in energy planning models should be prepared properly. Economic sectors` development depends on many factors which are usually considered in energy planning models. Thus, data on the development of such sectors as coal mining should be consistent with the economic assumptions made in the energy planning model. Otherwise, coal data could bias the results of the energy planning model. The coal mining and coal distribution models which have been developed at the Polish Academy of Sciences could provide proper coal data of use in ENPEP and other energy planning models. The coal mining model optimizes the most important decisions related to coal productions, such as coal mines development, retirement of non-profitable mines, and construction of new mines. The model uses basic data forecasts of coal mine costs and coal production. Other factors such as demand for coal, world coal prices, etc., are parameters which constitute constraints and requirements for the coal mining development. The output of the model is the amount of coal produced and supply curves for different coal types. Such data are necessary for the coal distribution model and could also be used by ENPEP. This paper describes the model, its structure and how the results of the model could serve as coal-related data for ENPEP. Improvement of some input data forms of the BALANCE module of ENPEP are also suggested in order to facilitate data preparation. (author). 7 figs.

Clean coal use in China: Challenges and policy implications

International Nuclear Information System (INIS)

Tang, Xu; Snowden, Simon; McLellan, Benjamin C.; Höök, Mikael

2015-01-01

Energy consumption in China is currently dominated by coal, a major source of air pollution and carbon emissions. The utilization of clean coal technologies is a likely strategic choice for China at present, however, although there have been many successes in clean coal technologies worldwide, they are not widely used in China. This paper examines the challenges that China faces in the implementation of such clean coal technologies, where the analysis shows that those drivers that have a negative bearing on the utilization of clean coal in China are mainly non-technical factors such as the low legal liability of atmospheric pollution related to coal use, and the lack of laws and mandatory regulations for clean coal use in China. Policies for the development of clean coal technologies are in their early stages in China, and the lack of laws and detailed implementation requirements for clean coal require resolution in order to accelerate China's clean coal developments. Currently, environmental pollution has gained widespread attention from the wider Chinese populace and taking advantage of this opportunity provides a space in which to regain the initiative to raise people’s awareness of clean coal products, and improve enterprises’ enthusiasm for clean coal. - Highlights: • Clean coal is not widely used in China due to many management issues. • Legal liability of pollution related with coal utilization is too low in China. • China is lack of laws and mandatory regulations for clean coal utilization. • It is difficult to accelerate clean coal utilization by incentive subsidies alone.

Modeling and optimization of processes for clean and efficient pulverized coal combustion in utility boilers

Directory of Open Access Journals (Sweden)

Belošević Srđan V.

2016-01-01

Full Text Available Pulverized coal-fired power plants should provide higher efficiency of energy conversion, flexibility in terms of boiler loads and fuel characteristics and emission reduction of pollutants like nitrogen oxides. Modification of combustion process is a cost-effective technology for NOx control. For optimization of complex processes, such as turbulent reactive flow in coal-fired furnaces, mathematical modeling is regularly used. The NOx emission reduction by combustion modifications in the 350 MWe Kostolac B boiler furnace, tangentially fired by pulverized Serbian lignite, is investigated in the paper. Numerical experiments were done by an in-house developed three-dimensional differential comprehensive combustion code, with fuel- and thermal-NO formation/destruction reactions model. The code was developed to be easily used by engineering staff for process analysis in boiler units. A broad range of operating conditions was examined, such as fuel and preheated air distribution over the burners and tiers, operation mode of the burners, grinding fineness and quality of coal, boiler loads, cold air ingress, recirculation of flue gases, water-walls ash deposition and combined effect of different parameters. The predictions show that the NOx emission reduction of up to 30% can be achieved by a proper combustion organization in the case-study furnace, with the flame position control. Impact of combustion modifications on the boiler operation was evaluated by the boiler thermal calculations suggesting that the facility was to be controlled within narrow limits of operation parameters. Such a complex approach to pollutants control enables evaluating alternative solutions to achieve efficient and low emission operation of utility boiler units. [Projekat Ministarstva nauke Republike Srbije, br. TR-33018: Increase in energy and ecology efficiency of processes in pulverized coal-fired furnace and optimization of utility steam boiler air preheater by using in

Steam coal processing technology: handling, high-order processing, COM, meth-coal

Energy Technology Data Exchange (ETDEWEB)

Kamata, H.; Onodera, J.

1982-01-01

Topics covered include: various handling techologies (overland and marine transport, storage, water removal, drying, comminution and sizing); various coal processing technologies (gravity concentration, magnetic separation, multi-stage flotation, liquid-phase pelletizing, chemical processing); production methods for coal-oil mixtures (COM), their physical properties, stability, storage, transport, advantages, plus recent trends in research and development; production of coal-methanol slurry (meth-coal), its stability, storage, transport, utilization and environmental problems, plus latest trends in research and development. (In Japanese)

Life cycle assessment ultra-clean micronized coal-water-oil fuel preparation and its usage in diesel engine

Energy Technology Data Exchange (ETDEWEB)

Fu, X.; Wang, Z.; Novelli, G.; Benedetti, B. [China University of Mining and Technology, Beijing (China)

2005-08-15

The study described the preparation of ultra-clean micronized coal-water-oil fuel (UCMWOF) and its usage in diesel engine. The production and usage of UCMCWOF and diesel oil, on a Life Cycle Assessment (LCA) basis, were evaluated. A comparison between the two systems shows that beside reducing of photochemical ozone creation potential and rest indicators in UCMCWOF increase. This predicates that the system of UCMCWOF is characterized by high global environmental impact, but its local impacts are lower if compared with the use of diesel and traditional coal. 3 refs., 3 figs., 3 tabs.

Computer-aided planning of brown coal seam mining in regard to coal quality

Energy Technology Data Exchange (ETDEWEB)

Ciesielski, R.; Lehmann, A.; Rabe, H.; Richter, S.

1988-09-01

Discusses features of the geologic SORVER software developed at the Freiberg Fuel Institute, GDR. The program processes geologic data from exploratory wells, petrographic characteristics of a coal seam model, technological mining parameters and coal quality requirements of consumers. Brown coal reserves of coking coal, gasification coal, briquetting coal and steam coal are calculated. Vertical seam profiles and maps of seam horizon isolines can be plotted using the program. Coal quality reserves along the surface of mine benches, mining block widths and lengths for excavators, maximum possible production of individual coal qualities by selective mining, and coal quality losses due to mining procedures are determined. The program is regarded as a means of utilizing deposit reserves more efficiently. 5 refs.

Black coal in Australia 1985-86

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

The annual publication contains comprehensive statistical details of the Australian black coal industry. Included are statistics on coal supply and disposal, production plant and equipment, coal preparation, capital expenditure, employees, exports, coal consumption, resources. Maps of mine locations are included, also tables showing coal supply and disposal, production figures, plant and equipment, employees, exports, resources.

Preparation and Evaluation of Adsorbents from Coal and Irvingia gabonensis Seed Shell

Science.gov (United States)

Ezeokonkwo, Mercy A.; Ofor, Okechukwu F.; Ani, Julius U.

2017-12-01

The adsorption of Cd(II) and Pb(II) ions on adsorbents prepared from sub-bituminous coal, lignite and a blend of coal and Irvingia gabonensis seed shells was investigated. Fourier transform infrared, scanning electron microscope and X-ray fluorescence analyses implicated hydroxyl, carbonyl, Al2O3 and SiO2 as being responsible for binding the metal ions on the porous adsorbents. The optimum adsorption of carbonized lignite for the removal of Cd(II) and Pb(II) ions from aqueous media were 80.93% and 87.85%, respectively. Batch adsorption was done by effect of adsorbent dosage, pH, contact time, temperature, particle size, and initial concentration. Equilibrium for the removal of Pb(II) and Cd(II) was established within 100 and 120 min respectively. Blending the lignite-derived adsorbent with Irvingia gabonensis seed shell improved the performance significantly. More improvement was observed on modification of the blend using NaOH and H3PO4. Pb(II) was preferentially adsorbed than Cd(II) in all cases. Adsorption of Cd(II) and Pb(II) ions followed Langmuir isotherm. The kinetics of adsorption was best described by pseudo-second order model. The potential for using a blend of coal and agricultural byproduct (Irvingia gabonensis seed shell) was found to be a viable alternative for removal of toxic heavy metals from aqueous solutions.

Preparation, characterization and utilization of starch nanoparticles.

Science.gov (United States)

Kim, Hee-Young; Park, Sung Soo; Lim, Seung-Taik

2015-02-01

Starch is one of the most abundant biopolymers in nature and is typically isolated from plants in the form of micro-scale granules. Recent studies reported that nano-scale starch particles could be readily prepared from starch granules, which have unique physical properties. Because starch is environmentally friendly, starch nanoparticles are suggested as one of the promising biomaterials for novel utilization in foods, cosmetics, medicines as well as various composites. An overview of the most up-to-date information regarding the starch nanoparticles including the preparation processes and physicochemical characterization will be presented in this review. Additionally, the prospects and outlooks for the industrial utilization of starch nanoparticles will be discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

The importance of coal in energy

International Nuclear Information System (INIS)

Onal, Guven

2006-01-01

An 87% of the total energy requirement of the world is supplied by fossil fuels such as coal, fuel oil, and natural gas, while the rest comes from the other sources, like hydroelectric and nuclear power plants. Coal, as a fuel oil equivalent, has the greatest reserves (70%) among the fossil fuels and is very commonly found in the world. While the share of coal in the production of electricity was 39% in 2004 it is expected to rise to 48% in 2020. In the direction of sustainable development, the utilization of coal in energy production is constantly increasing and related researches are continuing. Today, the development and economics of hybrid electricity production; gas, fluid fuel, and hydrogen production from coal are being investigated and their industrial applications are slowly emerging. The surprisingly sharp increase in fuel oil and natural gas prices proves the defectiveness of the energy strategies of Turkey in effect since the 1990. Turkey should turn to coal without wasting more time, accept the utilization of clean coal in energy production, and determine her road-map. Increasing the efficiency of thermal power plants which utilize coal; hybrid technology; and gas, fluid fuel, and hydrogen production technologies from coal are investigated in this paper and suggestions are made.

Study of the Korean anthracite for utilization and the coal mine data management

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

This report consists of two articles. (1) Petrographic study of the Korean anthracite for utilization (5): This research was initiated for the development of filtering materials those can be used in waste water treatment sites The small scale of filtration tester was built on the waste water treatment site of Chungjoo electric Co. to use waste water processed by purifying system for the feasibility study. (2) Study of the closed coal mine data management: Underground maps about 1700 adits of 100 coal mines, and related graphic data have been collected in the database. And all those data were entered into the database in vectorial form, coordinates obtaining from the digitizing tablet. Detailed works are described in the other report, including the discussions of graphic database and data handling of graphical mine data. Comments about the GIS is also provided in the volume. (author). 25 refs., 45 figs., 50 tabs., 3 maps.

The production of high load coal-water mixtures on the base of Kansk-Achinsk Coal Basin

Energy Technology Data Exchange (ETDEWEB)

Demidov, Y.; Bruer, G.; Kolesnikova, S. [Research and Design Institute for Problems of Development of Kansk-Achinsk Coal Basin (KATEKNilugol), Krasnoyarsk (Russian Federation)

1995-12-01

The results of the {open_quotes}KATEKNIIugol{close_quotes} work on the problems of high load coal-water mixtures are given in this article. General principles of the mixture production, short characteristics of Kansk-Achinsk coals, the experimental results of the coal mixture production on a test-industrial scale, the suspension preparation on the base of coal mixtures, technical-economical indexes of tested coal pipeline variants based on Kansk-Achinsk coals are described.

ASSESSMENT OF CONTROL TECHNOLOGIES FOR REDUCING EMISSIONS OF SO2 AND NOX FROM EXISTING COAL-FIRED UTILITY BOILERS

Science.gov (United States)

The report reviews information and estimated costs on 15 emissioncontrol technology categories applicable to existing coal-fired electric utility boilers. he categories include passive controls such as least emission dispatching, conventional processes, and emerging technologies ...

Life Cycle Assessment of Coal-fired Power Production

Energy Technology Data Exchange (ETDEWEB)

Spath, P. L.; Mann, M. K.; Kerr, D. R.

1999-09-01

Coal has the largest share of utility power generation in the US, accounting for approximately 56% of all utility-produced electricity (US DOE, 1998). Therefore, understanding the environmental implications of producing electricity from coal is an important component of any plan to reduce total emissions and resource consumption. A life cycle assessment (LCA) on the production of electricity from coal was performed in order to examine the environmental aspects of current and future pulverized coal boiler systems. Three systems were examined: (1) a plant that represents the average emissions and efficiency of currently operating coal-fired power plants in the US (this tells us about the status quo), (2) a new coal-fired power plant that meets the New Source Performance Standards (NSPS), and (3) a highly advanced coal-fired power plant utilizing a low emission boiler system (LEBS).

Competitive edge of western coal

International Nuclear Information System (INIS)

Keith, R.D.

1990-01-01

This paper expresses views on the competitive advantages of one of the nation's most remarkable energy resources--Western coal. It covers utilization of Western coal, and its advantages. The Arkansas Power and Light Company and its demand for coal are also covered

U.S. electric utility demand-side management 1995

International Nuclear Information System (INIS)

1997-01-01

The US Electric Utility Demand-Side Management report is prepared by the Coal and Electric Data and Renewables Division; Office of Coal, Nuclear, Electric and Alternative Fuels; Energy Information Administration (EIA); US Department of Energy. The report presents comprehensive information on electric power industry demand-side management (DSM) activities in the US at the national, regional, and utility levels. The objective of the publication is to provide industry decision makers, government policy makers, analysts, and the general public with historical data that may be used in understanding DSM as it relates to the US electric power industry. The first chapter, ''Profile: US Electric Utility Demand-Side Management'', presents a general discussion of DSM, its history, current issues, and a review of key statistics for the year. Subsequent chapters present discussions and more detailed data on energy savings, peak load reductions and costs attributable to DSM. 9 figs., 24 tabs

Gasification catalysts prepared by the reaction of CaCO3 and coal. Tansan karushiumu to sekitan no ion kokan hanno ni yori choseishita kokassei gas ka shokubai

Energy Technology Data Exchange (ETDEWEB)

Otsuka, Y.; Asami, K. (Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science)

1991-11-07

Properties of the active gasification catalysts prepared by ion exchange reaction of CaCO3 and coal were studied. Several kinds of Ca-loaded coal specimens were prepared to compare their properties among them by physically mixing coal particles with CaCO3 ones in air, by kneading both materials in pure water while crashing and by impregnating CaCO3 into coal while agitating them in pure water. Although Ca-loading onto the impregnated specimen was nearly one-half that of the kneaded one, its catalysis was equal to the kneaded one. CaCO3 greatly accelerated steam gasification only by mixing it with low rank coal in water, and such a high catalytic activity was caused by ion-exchanged Ca produced by the reaction between CaCO3 and COOH radical in coal. Aragonite of seashells yielded more Ca-loading than calcite of limestone, suggesting one of the useful treatment of seashell waste. 3 refs., 4 figs., 2 tabs.

Preparation of thiol-functionalized activated carbon from sewage sludge with coal blending for heavy metal removal from contaminated water.

Science.gov (United States)

Li, Juan; Xing, Xing; Li, Jiao; Shi, Mei; Lin, Aijun; Xu, Congbin; Zheng, Jianzhong; Li, Ronghua

2018-03-01

Sewage sludge produced from wastewater treatment is a pressing environmental issue. Mismanagement of the massive amount of sewage sludge would threat our valuble surface and shallow ground water resources. Use of activated carbon prepared from carbonization of these sludges for heavy metal removal can not only minimize and stabilize these hazardous materials but also realize resources reuse. In this study, thiol-functionalized activated carbon was synthesized from coal-blended sewage sludge, and its capacity was examined for removing Cu(II), Pb(II), Cd(II) and Ni(II) from water. Pyrolysis conditions to prepare activated carbons from the sludge and coal mixture were examined, and the synthesized material was found to achieve the highest BET surface area of 1094 m 2 /g under 500 °C and 30 min. Batch equilibrium tests indicated that the thiol-functionalized activated carbon had a maximum sorption capacity of 238.1, 96.2, 87.7 and 52.4 mg/g for Pb(II), Cd(II), Cu(II) and Ni(II) removal from water, respectively. Findings of this study suggest that thiol-functionalized activated carbon prepared from coal-blended sewage sludge would be a promising sorbent material for heavy metal removal from waters contaminated with Cu(II), Pb(II), Cd(II) and Ni(II). Copyright © 2017 Elsevier Ltd. All rights reserved.

EIA projections of coal supply and demand

International Nuclear Information System (INIS)

Klein, D.E.

1989-01-01

Contents of this report include: EIA projections of coal supply and demand which covers forecasted coal supply and transportation, forecasted coal demand by consuming sector, and forecasted coal demand by the electric utility sector; and policy discussion

Investigation on the activation of coal gangue by a new compound method.

Science.gov (United States)

Li, Chao; Wan, Jianhua; Sun, Henghu; Li, Longtu

2010-07-15

In order to comprehensively utilize coal gangue as the main raw material in cementitious materials, improving its cementitious activity is a question of fundamental importance. In this paper, we present a new compound mechanical-hydro-thermal activation (CMHTA) technology to investigate the activation effect of coal gangue, and the traditional mechanical-thermal activation (TMTA) technology was used as reference. The purpose of this study is to give a detailed comparison between these two methods with regard to the mineral composition, crystal structure and microstructure, by XRD, IR, MAS NMR, XPS and mechanical property analysis. The prepared coal gangue based blended cement, containing 52% of activated coal gangue C (by CMHTA technology), has a better mechanical property than activated coal gangue T (by TMTA technology) and raw coal gangue. The results show that both of the TMTA and CMHTA technologies can improve the cementitious activity of raw gangue greatly. Moreover, compared with TMTA, the mineral phases such as feldspar and muscovite in raw coal gangue were partially decomposed, and the crystallinity of quartz decreased, due to the effect of adding CaO and hydro-thermal process of CMHTA technology. 2010 Elsevier B.V. All rights reserved.

Utilization of coal fly ash in solidification of liquid radioactive waste from research reactor.

Science.gov (United States)

Osmanlioglu, Ahmet Erdal

2014-05-01

In this study, the potential utilization of fly ash was investigated as an additive in solidification process of radioactive waste sludge from research reactor. Coal formations include various percentages of natural radioactive elements; therefore, coal fly ash includes various levels of radioactivity. For this reason, fly ashes have to be evaluated for potential environmental implications in case of further usage in any construction material. But for use in solidification of radioactive sludge, the radiological effects of fly ash are in the range of radioactive waste management limits. The results show that fly ash has a strong fixing capacity for radioactive isotopes. Specimens with addition of 5-15% fly ash to concrete was observed to be sufficient to achieve the target compressive strength of 20 MPa required for near-surface disposal. An optimum mixture comprising 15% fly ash, 35% cement, and 50% radioactive waste sludge could provide the solidification required for long-term storage and disposal. The codisposal of radioactive fly ash with radioactive sludge by solidification decreases the usage of cement in solidification process. By this method, radioactive fly ash can become a valuable additive instead of industrial waste. This study supports the utilization of fly ash in industry and the solidification of radioactive waste in the nuclear industry.

Research and development to prepare and characterize robust coal/biomass mixtures for direct co-feeding into gasification systems

Energy Technology Data Exchange (ETDEWEB)

Felix, Larry [Inst. Of Gas Technology, Des Plaines, IL (United States); Farthing, William [Inst. Of Gas Technology, Des Plaines, IL (United States); Hoekman, S. Kent [Inst. Of Gas Technology, Des Plaines, IL (United States)

2014-12-31

This project was initiated on October 1, 2010 and utilizes equipment and research supported by the Department of Energy, National Energy Technology Laboratory, under Award Number DE- FE0005349. It is also based upon previous work supported by the Department of Energy, National Energy Technology Laboratory, under Award Numbers DOE-DE-FG36-01GOl1082, DE-FG36-02G012011 or DE-EE0000272. The overall goal of the work performed was to demonstrate and assess the economic viability of fast hydrothermal carbonization (HTC) for transforming lignocellulosic biomass into a densified, friable fuel to gasify like coal that can be easily blended with ground coal and coal fines and then be formed into robust, weather-resistant pellets and briquettes.

A bottom-up method to develop pollution abatement cost curves for coal-fired utility boilers

International Nuclear Information System (INIS)

Vijay, Samudra; DeCarolis, Joseph F.; Srivastava, Ravi K.

2010-01-01

This paper illustrates a new method to create supply curves for pollution abatement using boiler-level data that explicitly accounts for technology cost and performance. The Coal Utility Environmental Cost (CUECost) model is used to estimate retrofit costs for five different NO x control configurations on a large subset of the existing coal-fired, utility-owned boilers in the US. The resultant data are used to create technology-specific marginal abatement cost curves (MACCs) and also serve as input to an integer linear program, which minimizes system-wide control costs by finding the optimal distribution of NO x controls across the modeled boilers under an emission constraint. The result is a single optimized MACC that accounts for detailed, boiler-specific information related to NO x retrofits. Because the resultant MACCs do not take into account regional differences in air-quality standards or pre-existing NO x controls, the results should not be interpreted as a policy prescription. The general method as well as NO x -specific results presented here should be of significant value to modelers and policy analysts who must estimate the costs of pollution reduction.

Properties of sorbents from brown coal

Energy Technology Data Exchange (ETDEWEB)

Straka, P.; Buchtele, J. [Academy of Sciences of the Czech Republic, Prague (Czech Republic)

2000-07-01

The surface and sorptional properties of carbonaceous materials prepared from brown coal and their relation to minerals content and coal bulk density as technologically important parameters of starting coal were described. Chars were prepared from brown coal of North Bohemian Brown Coal District and activated with CO{sub 2} in a large-scale laboratory unit. Their surface and sorptive properties were investigated. It was found that mineral matter/ash content favourably affects the mesoporosity development in chars/activated chars as the sorption capacity increased with increasing ash content in chars. No influence of ash content on the macroporosity was observed. With the activated chars, both the inner surface and sorption capacity showed the maximum in the burn-off range of 41-64%. Optimization of the process is discussed.

Coal: Energy for the future

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-05-01

This report was prepared in response to a request by the US Department of energy (DOE). The principal objectives of the study were to assess the current DOE coal program vis-a-vis the provisions of the Energy Policy Act of 1992 (EPACT), and to recommend the emphasis and priorities that DOE should consider in updating its strategic plan for coal. A strategic plan for research, development, demonstration, and commercialization (RDD and C) activities for coal should be based on assumptions regarding the future supply and price of competing energy sources, the demand for products manufactured from these sources, technological opportunities, and the need to control the environmental impact of waste streams. These factors change with time. Accordingly, the committee generated strategic planning scenarios for three time periods: near-term, 1995--2005; mid-term, 2006--2020; and, long-term, 2021--2040. The report is divided into the following chapters: executive summary; introduction and scope of the study; overview of US DOE programs and planning; trends and issues for future coal use; the strategic planning framework; coal preparation, coal liquid mixtures, and coal bed methane recovery; clean fuels and specialty products from coal; electric power generation; technology demonstration and commercialization; advanced research programs; conclusions and recommendations; appendices; and glossary. 174 refs.

Report of base consolidation promotion survey of overseas coal import in FY 1993. Feasibility survey of effective utilization of coal ash; 1993 nendo kaigaitan yunyu kiban seibi sokushin chosa. Sekitanbai yuko riyo jigyo no feasibility chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

This report describes the effective utilization of coal ash discharged from general industry (general industry ash) as improving material of construction waste soil and deodorant for poultry industry. Coal ash is characterized by the pozzolan and self-hardening properties which are not shown in soil and sand. Coal ash having a large amount of free CaO in its composition has stronger such properties. Coal ash generated from fluidized bed combustor which is a kind of combustor of coal contains a large amount of free CaO, especially, resulting in the stronger such properties. On the other hand, coal ash has water and oil absorbing property due to its porous structure. To utilize these properties, the improving material of soft construction waste soil and deodorant for poultry industry have been selected. As a result of laboratory and field tests for the former, it was found that sufficient supporting force can be obtained. Since the protection of powder splash is required at the site, a humidification system has been developed, which can protect the splash by the humidification of 5%. The price between 500 and 1,000 yen/ton is suitable for the improving material of construction waste soil. The maximum price of the deodorant for poultry industry is 10 yen/kg. 14 refs., 40 figs., 49 tabs.

GC/MS analysis of coal tar composition produced from coal pyrolysis

African Journals Online (AJOL)

Coal tar is a significant product generated from coal pyrolysis. A detailed analytical study on its composition and chemical structure will be of great advantage to its further processing and utilization. Using a combined method of planigraphy-gas chromatograph/mass spectroscopy (GC/MS), this work presents a composition ...

Clean coal technologies: A business report

International Nuclear Information System (INIS)

Anon.

1993-01-01

The book contains four sections as follows: (1) Industry trends: US energy supply and demand; The clean coal industry; Opportunities in clean coal technologies; International market for clean coal technologies; and Clean Coal Technology Program, US Energy Department; (2) Environmental policy: Clean Air Act; Midwestern states' coal policy; European Community policy; and R ampersand D in the United Kingdom; (3) Clean coal technologies: Pre-combustion technologies; Combustion technologies; and Post-combustion technologies; (4) Clean coal companies. Separate abstracts have been prepared for several sections or subsections for inclusion on the data base

Coal slurries: An environmental bonus?

International Nuclear Information System (INIS)

Basta, N.; Moore, S.; Ondrey, G.

1994-01-01

Developers and promoters of coal-water slurries and similar CWF (coal-water fuel) technologies have had a hard time winning converts since they unveiled their first commercial processes in the 1970s. The economic appeal of such processes, marginal at best, varies with the price of oil. Nevertheless, the technology is percolating, as geopolitics and environmental pressures drive new processes. Such fuels are becoming increasingly important to coal-rich, oil-poor nations such as China, as they attempt to build an onshore fuel supply. Meanwhile, improvements are changing the way coal-fired processes are viewed. Where air pollution regulations once discouraged the use of coal fuels, new coal processes have been developed that cut nitrous oxides (NOx) emissions and provide a use for coal fines, previously viewed as waste. The latest developments in the field were all on display at the 19th International Technical Conference on Coal Utilization and Fuel Systems, held in Clearwater, Fla., on March 21--24. At this annual meeting, sponsored by the Coal and Slurry Technology Association, (Washington, D.C.) and the Pittsburgh Energy Technology Center of the US Dept. of Energy (PETC), some 200 visitors from around the work gathered to discuss the latest developments in coal slurry utilization--new and improved processes, and onstream plants. This paper presents highlights from the conference

Development of upgraded brown coal process

Energy Technology Data Exchange (ETDEWEB)

Komatsu, N.; Sugita, S.; Deguchi, T.; Shigehisa, T.; Makino, E. [Kobe Steel Ltd., Hyogo (Japan). Coal and Energy Project Department

2004-07-01

Half of the world's coal resources are so-called low rank coal (LRC) such as lignite, subbituminous coal. Utilization of such coal is limited due to low heat value and high propensity of spontaneous combustion. Since some of LRCs have advantages as clean coal, i.e. low ash and low sulfur content, LRC can be the excellent feedstock for power generation and metallurgy depending on the upgrading technology. The UBC (upgraded brown coal) process introduced here converts LRC to solid fuel with high heat value and less propensity of self-heating. Various world coals, such as Australian, Indonesian and USA LRC, were tested using the Autoclave and Bench Scale Unit, and the process application to LRC of wide range is proven. The R & D activities of the UBC process are introduced including a demonstration project with a 5 ton/day test plant in progress in Indonesia, expecting near future commercialisation in order to utilize abundant LRC of clean properties. 8 refs., 12 figs., 3 tabs.

Coal in Europe: what future?: prospects of the coal industry and impacts study of the Kyoto Protocol

International Nuclear Information System (INIS)

Rudianto, E.

2006-12-01

From the industrial revolution to the 1960's, coal was massively consumed in Europe and its utilization was constantly raised. In the aftermath of World War II, coal had also an important part in reconstruction of Western Europe's economy. However, since the late 1960's, its demand has been declining. There is a (mis)conception from a number of policy makers that saying coal mining and utilizations in Europe is unnecessary. Therefore in the European Union (EU) Green Paper 2000, coal is described as an 'undesirable' fuel and the production of coal on the basis of economic criteria has no prospect. Furthermore, the commitment to the Kyoto Protocol in reducing greenhouse gases emission has aggravated this view. Faced with this situation, the quest for the future of coal industry (mining and utilization) in the lines of an energy policy is unavoidable. This dissertation did a profound inquiry trying to seek answers for several questions: Does the European Union still need coal? If coal is going to play a part in the EU, where should the EU get the coal from? What should be done to diminish negative environmental impacts of coal mining and utilization? and finally in regard to the CO 2 emission concerns, what will the state of the coal industry in the future in the EU? To enhance the analysis, a system dynamic model, called the Dynamics Coal for Europe (the DCE) was developed. The DCE is an Energy-Economy-Environment model. It synthesizes the perspectives of several disciplines, including geology, technology, economy and environment. It integrates several modules including exploration, production, pricing, demand, import and emission. Finally, the model emphasizes the impact of delays and feed-back in both the physical processes and the information and decision-making processes of the system. The calibration process for the DCE shows that the model reproduces past numbers on the scale well for several variables. Based on the results of this calibration process, it can

Forecast and Prevention of Coal and Gas Outbursts in the Case of Application of a New Mining Method - Drilling of a Coal Pillar

Directory of Open Access Journals (Sweden)

Vlastimil Hudeček

2010-10-01

Full Text Available Coal and gas outbursts are one of risk factors accompanying the mining of coal in low seams in the Ostrava-Karviná Coalfield.At the use of the method of longwall mining, all coal reserves have not been mined out owing to tectonic faults. For mining outthe residual reserves, the application of a new mining method - drilling of a coal pillar was proposed.The method of mining of a coal seam utilizing long large diameter boreholes is verified in the Paskov Mine (company OKD, JSC –Czech Republic under conditions of rock mass with hazard of rock and gas outbursts in localities of residual pillars left in seams afterfinishing the mining operations performed with using the classical method of longwall working along the strike. [5]Forecast and preventive measures applied to the verification of the new method were based on previous experience withthe mining of seams with hazard of coal and gas outbursts. They accepted fully valid legislation, i.e. Ordinance of Ostrava RegionalMining Authority No. 3895/2002 and supplementary materials (Instructions and Guidelines. The proposed measures respectedthe character of the method being verified. [4]For all areas being mined, projects containing also chapters specifying the problems of ensuring the safety of mining worksand operation under conditions of hazard of coal and gas outbursts were prepared.In the contributions, basic proposals for the principles of coal and gas outburst forecast and prevention when applying the newmining method – drilling of a coal pillar are presented

Strontium isotope study of coal utilization by-products interacting with environmental waters.

Science.gov (United States)

Spivak-Birndorf, Lev J; Stewart, Brian W; Capo, Rosemary C; Chapman, Elizabeth C; Schroeder, Karl T; Brubaker, Tonya M

2012-01-01

Sequential leaching experiments on coal utilization by-products (CUB) were coupled with chemical and strontium (Sr) isotopic analyses to better understand the influence of coal type and combustion processes on CUB properties and the release of elements during interaction with environmental waters during disposal. Class C fly ash tended to release the highest quantity of minor and trace elements-including alkaline earth elements, sodium, chromium, copper, manganese, lead, titanium, and zinc-during sequential extraction, with bottom ash yielding the lowest. Strontium isotope ratios ((87)Sr/(86)Sr) in bulk-CUB samples (total dissolution of CUB) are generally higher in class F ash than in class C ash. Bulk-CUB ratios appear to be controlled by the geologic source of the mineral matter in the feed coal, and by Sr added during desulfurization treatments. Leachates of the CUB generally have Sr isotope ratios that are different than the bulk value, demonstrating that Sr was not isotopically homogenized during combustion. Variations in the Sr isotopic composition of CUB leachates were correlated with mobility of several major and trace elements; the data suggest that arsenic and lead are held in phases that contain the more radiogenic (high-(87)Sr/(86)Sr) component. A changing Sr isotope ratio of CUB-interacting waters in a disposal environment could forecast the release of certain strongly bound elements of environmental concern. This study lays the groundwork for the application of Sr isotopes as an environmental tracer for CUB-water interaction. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Coal Data: A reference

International Nuclear Information System (INIS)

1991-01-01

The purpose of Coal Data: A Reference is to provide basic information on the mining and use of coal, an important source of energy in the United States. The report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ''Coal Terminology and Related Information'' provides additional information about terms mentioned in the text and introduces new terms. Topics covered are US coal deposits, resources and reserves, mining, production, employment and productivity, health and safety, preparation, transportation, supply and stocks, use, coal, the environment, and more. (VC)

Characterization and supply of coal based fuels. Volume 1, Final report and appendix A (Topical report)

Energy Technology Data Exchange (ETDEWEB)

1992-06-01

Studies and data applicable for fuel markets and coal resource assessments were reviewed and evaluated to provide both guidelines and specifications for premium quality coal-based fuels. The fuels supplied under this contract were provided for testing of advanced combustors being developed under Pittsburgh Energy Technology Center (PETC) sponsorship for use in the residential, commercial and light industrial (RCLI) market sectors. The requirements of the combustor development contractors were surveyed and periodically updated to satisfy the evolving needs based on design and test experience. Available coals were screened and candidate coals were selected for further detailed characterization and preparation for delivery. A team of participants was assembled to provide fuels in both coal-water fuel (CWF) and dry ultrafine coal (DUC) forms. Information about major US coal fields was correlated with market needs analysis. Coal fields with major reserves of low sulfur coal that could be potentially amenable to premium coal-based fuels specifications were identified. The fuels requirements were focused in terms of market, equipment and resource constraints. With this basis, the coals selected for developmental testing satisfy the most stringent fuel requirements and utilize available current deep-cleaning capabilities.

The effects of topical corticosteroids and a coal tar preparation on dithranol-induced irritation in patients with psoriasis

Energy Technology Data Exchange (ETDEWEB)

Swinkels, O.Q.J.; Kucharekova, M.; Prins, M.; Gerritsen, M.J.P.; van der Valk, P.G.M.; van de Kerkhof, P.C.M. [University of Nijmegen, Nijmegen (Netherlands). Medical Center

2003-02-01

Dithranol has been a mainstay in the treatment of psoriasis for more than 80 years. Although a safe approach, the irritation of the clinically uninvolved perilesional skin remains a major limitation of this treatment. Corticosteroids and coal tar solution have an anti-inflammatory potential. The aim of the present study was to investigate the clinical and cell-biological effects of two topical corticosteroids and a coal tar preparation on dithranol-irritated skin. The expression of epidermal proliferation, differentiation and inflammation markers and the clinical irritation scores indicate that the application of a high potency corticosteroid is the best approach to minimise dithranol irritation.

40 CFR 60.254 - Standards for coal processing and conveying equipment, coal storage systems, transfer and loading...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Standards for coal processing and conveying equipment, coal storage systems, transfer and loading systems, and open storage piles. 60.254... (CONTINUED) STANDARDS OF PERFORMANCE FOR NEW STATIONARY SOURCES Standards of Performance for Coal Preparation...

Coal and sustainable development: utilities and activity

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

Reflecting its continuing focus on coal and sustainable development, the CIAB surveyed its Members about their attitudes to sustainable development and to obtain information on sustainable development activities within their organisations. The survey revealed that awareness of the importance of sustainable development has increased significantly in the past three years, with a clear majority of respondents seeing it as aligning with their commercial objectives. Reducing emissions from coal use is seen as the key priority, although the importance of this relative to other priorities varies on a regional basis depending on local circumstances. While a large majority of respondents recognised the importance of sustainable development and its increasing influence on decision-making within the coal industry, there was a wide range in the extent of activities. Some organisations have embarked on broad initiatives to better align their practices to sustainable development priorities. The range of activities suggests an evolutionary process - one that commences with a sole internal focus on economic priorities for the business, and then broadens to include local environmental issues and the community. Leading organisations are now moving to look more at global issues, to recognise and share the responsibility for the social and environmental impacts of producing and using their products, and to better engage stakeholders. 4 figs.

FY 1999 report on the potential survey of the environmentally friendly type coal utilization system. Potential survey of the environmentally friendly type coal utilization system in the Philippines; 1999 nendo chosa hokokusho. Kankyo chowa gata sekitan riyo system kanosei chosa (Firipin ni okeru kankyo chowa gata system kanosei chosa)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

For the purpose of contributing to working out a master plan for the introduction of the environmentally friendly type coal utilization system in the Philippines, analysis was made of the state of coal use/the state of spread by industry mostly including the electric power industry, cement industry and residential/commercial use fuel sector. In the Philippines, the amount of coal use has rapidly been increasing since coal-fired power plants started operation. For the promotion of the use of domestic coals, it is important to reform low grade coal. Moreover, the technology is required which copes with the reinforced regulation against SOx emissions. In the cement industry, coal and coal ash have not yet been effectively used. Therefore, the following measures should be taken to increase the competitive force: energy conservation measures, reinforcement of environmental measures such as dust prevention, and effective use of the fly ash emitted from power plants. In general households and small-/medium-sized industries such as tobacco drying, they still use a large amount of charcoals and firewood, which is approximately 86% of the residential/commercial use energy. There is a growing tendency for the development/spread of coal briquette as substituting energy. (NEDO)

An experimental study on the hazard assessment and mechanical properties of porous concrete utilizing coal bottom ash coarse aggregate in Korea.

Science.gov (United States)

Park, Seung Bum; Jang, Young Il; Lee, Jun; Lee, Byung Jae

2009-07-15

This study evaluates quality properties and toxicity of coal bottom ash coarse aggregate and analyzes mechanical properties of porous concrete depending on mixing rates of coal bottom ash. As a result, soundness and resistance to abrasion of coal bottom ash coarse aggregate were satisfied according to the standard of coarse aggregate for concrete. To satisfy the standard pertaining to chloride content, the coarse aggregates have to be washed more than twice. In regards to the result of leaching test for coal bottom ash coarse aggregate and porous concrete produced with these coarse aggregates, it was satisfied with the environment criteria. As the mixing rate of coal bottom ash increased, influence of void ratio and permeability coefficient was very little, but compressive and flexural strength decreased. When coal bottom ash was mixed over 40%, strength decreased sharply (compressive strength: by 11.7-27.1%, flexural strength: by maximum 26.4%). Also, as the mixing rate of coal bottom ash increased, it was confirmed that test specimens were destroyed by aggregate fracture more than binder fracture and interface fracture. To utilize coal bottom ash in large quantities, it is thought that an improvement method in regards to strength has to be discussed such as incorporation of reinforcing materials and improvement of aggregate hardness.

Evaluation of dense-phase ultrafine coal (DUC) as a fuel alternative for oil- and gas-designed boilers and heaters. Final report

Energy Technology Data Exchange (ETDEWEB)

1986-12-01

Utility and industrial firms currently using oil- and gas-fired boilers have an interest in substitution of coal for oil and gas as the primary boiler fuel. This interest stems from coal`s two main advantages over oil and gas-lower cost and security of supply. Recent efforts in the area of coal conversion have been directed to converting oil- and gas- fired boilers which were originally designed for coal-firing or were designed with some coal-firing capability. Boilers designed exclusively for oil- or gas-firing have not been considered viable candidates for coal conversion because they generally require a significant capacity derating and extensive and costly modifications. As a result, conversion of boilers in this class to coal-firing has generally been considered unattractive. Renewed interest in the prospects for converting boilers designed exclusively for oil- and gas-firing to coal firing has centered around the concept of using ``ultra fine`` coal as opposed to ``conventional grind`` pulverized coal. The main distinction being the finer particle size to which the former is ground. This fuel type may have characteristics which ameliorate many of the boiler problems normally associated with pulverized coal-firing. The overall concept for ultrafine coal utilization is based on a regional large preparation plant with distribution of a ready to fire fuel directly to many small users. This differs from normal practice in which final coal sizing is performed in pulverizers at the user`s site.

Coal chemistry and technology. Komur Kimyasi ve Teknolojisi

Energy Technology Data Exchange (ETDEWEB)

Kural, O [ed.

1988-01-01

The 18 chapters cover the following topics: mining in Turkey; formation, petrography and classification of coal; chemical and physical properties of coal; mechanical properties of coal; spontaneous combustion of coal and the methods of prevention; sampling of coal; coal preparation and plants; desulfurization of coal; bituminous coal and its consumption; lignite and its consumption; world coal trade and transportation; other important carbon fuels; briquetting of coal; carbonization and coking formed coke; liquefaction of coal; gasification of coal; underground gasification of coal; and combustion models, fluidized-bed combustion, furnaces. An English-Turkish coal dictionary is included. 641 refs., 244 figs., 108 tabs.

JV Task 6 - Coal Ash Resources Research Consortium Research

Energy Technology Data Exchange (ETDEWEB)

Debra Pflughoeft-Hassett; Tera Buckley; Bruce Dockter; Kurt Eylands; David Hassett; Loreal Heebink; Erick Zacher

2008-04-01

The Coal Ash Resources Research Consortium{reg_sign} (CARRC{reg_sign}, pronounced 'cars') focuses on performing fundamental and applied scientific and engineering research emphasizing the environmentally safe, economical use of coal combustion by-products (CCBs). CARRC member organizations, which include utilities and marketers, are key to developing industry-driven research in the area of CCB utilization and ensuring its successful application. The U.S. Department of Energy is a partner in CARRC through the EERC Jointly Sponsored Research Program (JSRP), which provides matching funds for industrial member contributions and facilitates an increased level of effort in CARRC. CARRC tasks were designed to provide information on CCB performance, including environmental performance, engineering performance, favorable economics, and improved life cycle of products and projects. CARRC technical research tasks are developed based on member input and prioritization. CARRC special projects are developed with members and nonmembers to provide similar information and to support activities, including the assembly and interpretation of data, support for standards development and technology transfer, and facilitating product development and testing. CARRC activities from 1998 to 2007 included a range of research tasks, with primary work performed in laboratory tasks developed to answer specific questions or evaluate important fundamental properties of CCBs. CARRC topical reports were prepared on several completed tasks. Specific CARRC 1998B2007 accomplishments included: (1) Development of several ASTM International Standard Guides for CCB utilization applications. (2) Organization and presentation of training courses for CCB professionals and teachers. (3) Development of online resources including the Coal Ash Resource Center, Ash from Biomass in Coal (ABC) of cocombustion ash characteristics, and the Buyer's Guide to Coal-Ash Containing Products. In addition

Report on the 1997 Coal Engineer Training Program General Course Training; 1997 nendo sekitan gijutsusha yosei jigyo ippan course kenshu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-01

The paper reported training in the fiscal 1997 coal engineer training course. The training was made in a period from June 9 to November 12 in terms of actual training, English training, joint seminar, visits to the related facilities in Japan, overseas training, etc. for 10 engineers from mining companies, oil companies and electric power companies. In the actual training, the following lectures were given at International Resource University in Akita prefecture: coal exploration technology, coal situation of Australia, physical/chemical characteristics of coal and the application, coal preparation technology, coal situation in India, coal situation in the U.S., trend of general coal demand, coal situation in China, coal mining technology, actual surface mining technology, coal situation in Canada, commercial English, trend of raw coal demand, coal geology, environmental protection technology related to coal utilization, etc. Overseas training, which was divided into an Australia group and a Canada/America group, was conducted for about a month. Training in Indonesia was canceled because of a large scale forest fire which broke out immediately before the start. 88 figs., 52 tabs.

Clean Coal Program Research Activities

Energy Technology Data Exchange (ETDEWEB)

Larry Baxter; Eric Eddings; Thomas Fletcher; Kerry Kelly; JoAnn Lighty; Ronald Pugmire; Adel Sarofim; Geoffrey Silcox; Phillip Smith; Jeremy Thornock; Jost Wendt; Kevin Whitty

2009-03-31

Although remarkable progress has been made in developing technologies for the clean and efficient utilization of coal, the biggest challenge in the utilization of coal is still the protection of the environment. Specifically, electric utilities face increasingly stringent restriction on the emissions of NO{sub x} and SO{sub x}, new mercury emission standards, and mounting pressure for the mitigation of CO{sub 2} emissions, an environmental challenge that is greater than any they have previously faced. The Utah Clean Coal Program addressed issues related to innovations for existing power plants including retrofit technologies for carbon capture and sequestration (CCS) or green field plants with CCS. The Program focused on the following areas: simulation, mercury control, oxycoal combustion, gasification, sequestration, chemical looping combustion, materials investigations and student research experiences. The goal of this program was to begin to integrate the experimental and simulation activities and to partner with NETL researchers to integrate the Program's results with those at NETL, using simulation as the vehicle for integration and innovation. The investigators also committed to training students in coal utilization technology tuned to the environmental constraints that we face in the future; to this end the Program supported approximately 12 graduate students toward the completion of their graduate degree in addition to numerous undergraduate students. With the increased importance of coal for energy independence, training of graduate and undergraduate students in the development of new technologies is critical.

The future of coal-fired generation

Energy Technology Data Exchange (ETDEWEB)

White, G. [Sherritt International Corp., Calgary, AB (Canada)

2004-07-01

The 3 features that will ensure coal's place as a primary energy source are its affordability, availability and its abundance. Coal reserves represent more than 200 years of supply. Graphs depicting coal consumption in North America, Central and South America, Western Europe, Easter Europe, Middle East, Africa, and Asia show that coal use is expected to grow 1.5 per cent annually. Asia is the greatest consumer of coal, while the consumption of coal in Eastern Europe is steadily declining. About half of the electricity supply in the United States will continue to be generated by coal and non-electrical utilization is also expected to grow. Emerging technologies that are promoting efficiency of coal utilization include combustion technology, clean coal technology, conversion technology and emissions technology. These technologies also address environmental concerns regarding coal combustion, such as removal of carbon dioxide through sequestration and reduction in nitrogen oxides, sulphur dioxide and particulates. Mercury mitigation technologies are also being developed. It was noted that the use of coal is mitigated by other available supply such as nuclear, natural gas and hydro which provide the base load generation. Renewable energy supply can meet up to 20 per cent of the base load, while coal can fill be gap between base load and peak loads. It was noted that the use of coal in direct industrial processes allows for synergies such as syngas for bitumen upgrading, coal as a chemical feedstock with electricity as a by-product, combined heat and power and cogeneration. tabs., figs.

Washability of Australian coals

Energy Technology Data Exchange (ETDEWEB)

Whitmore, R L

1979-06-01

Australian coals tend to be young in geological age and high in ash by world standards; preparation of the coal before marketing is almost universal. On the basis of float and sink data from 39 locations in the eastern Australian coalfields, the coals are place in four categories representing increasing difficulty in their washability characteristics. These seem to be related neither to the geological age nor the geographical position of the deposit and Hunter Valley coals, for example, span all categories. The influence of crushing on the washability of Australian coals is briefly considered and from limited data it is concluded to be appreciably smaller than for British or North American coals. A strategy for the float and sink analysis of Australian coals is proposed and the influence of washability characteristics on current trends in the selection of separating processes for coking and steaming products is discussed.

Environmental pollution caused by coal mining and utilization in China; Umweltbelastungen durch Kohlefoerderung und -nutzung in China

Energy Technology Data Exchange (ETDEWEB)

Bai, Fuchen [Guangdong Ocean Univ., Zhanjiang (China). Dept. of Scientific Research Management

2013-07-15

After the BP Statistical Review of World Energy of 2010 45.6% of coal production and 46.9% of coal consumption in the world in 2009 are accounted for China. The large-scale coal production and use cause major environmental impacts. A large environmental impact is through the emission of some unavoidable reaction products (for example waste gas, waste heat) that affect and damage the ecosystem. A steady influence can lead to long-term climate changes and medium term damage to the ecosystem. Other environmental impacts occur during mining of coal by the change in the water balance and the transformation of the landscape (surface mining, spoil tips). The environmental problems caused by coal mining and utilization can not be ignored in China. [German] Nach der BP-Statistik der Weltenergie 2010 sind 45,6% der Kohleproduktion und 46,9% des Kohleverbrauchs in der Welt im Jahr 2009 auf China entfallen. Die grossangelegte Kohlefoerderung und -verwendung fuehren zu grossen Umweltbelastungen. Eine grosse Umweltbeeinflussung erfolgt durch die Emission von zum Teil unvermeidbaren Umsetzungsprodukten (zum Beispiel Abgas, Abwaerme), die das Oekosystem beeinflussen und schaedigen. Eine stetige Beeinflussung kann langfristig zu den Klimaveraenderungen und mittelfristig zur Schaedigung des Oekosystems fuehren. Weitere Umweltbelastungen erfolgen beim Abbau der Kohle durch die Veraenderung des Wasserhaushalts und durch die Umgestaltung der Landschaft (Tagebau, Abbauhalden). Die Umweltprobleme, die durch die Kohlefoerderung und -nutzung verursacht werden, koennen in China nicht ignoriert werden.

Environmental impact of coal mine methane emissions and responding strategies in China

Energy Technology Data Exchange (ETDEWEB)

Cheng, Y.P.; Wang, L.; Zhang, X.L. [China University of Mining & Technology, Xuzhou (China)

2011-01-15

The impact on global climate change from coal mine methane emissions in China has been drawing attention as coal production has powered its economic development. Data on coal mine methane emissions from the State Administration of Coal Mine Safety of China has been analyzed. It is estimated that the methane emission from coal mining in China reached 20 billions of cubic meters in 2008, most of which comes from state-owned coal mines with high-gas content. China releases six times as much of methane from coal mines as compared to the United States. However, Chinese methane emission from coal production accounts for only a very small proportion on the environmental impact when compared to emissions of carbon dioxide from fossil fuel consumption. The Chinese government has shown environmental awareness and resolution on the mitigation and utilization of coal mine methane emissions. Measures have been taken to implement the programs of mitigation and utilization of coal mine methane, and at the same time, to ensure mining safety. Nearly 7.2 billions of cubic meters of methane were drained from the coal mines, and 32% of it was utilized in 2008. The slow advancement of technologies for the drainage and utilization of low-concentration methane from ventilation air hinders the progress of mitigation of atmospheric methane and the utilization of coal mine methane emissions.

Low-shear rheology and sedimentation stability of coal-oil dispersions

Energy Technology Data Exchange (ETDEWEB)

Rutter, P. R.; Davies, J. M.; Jones, T. E.R.

1984-10-15

Stable coal-oil mixtures can be prepared by grinding coal particles in fuel oil. These products have been prepared by the British Petroleum Company plc and are referred to as Coal-Oil Dispersions (COD). One of the major problems associated with the production of DOD is the rapid assessment of the length of time the coal particles are likely to remain in suspension under a particular set of storage conditions. This paper describes a number of measurements of the low-shear rheology and sedimentation stability of a series of CODs prepared by grinding two types of coal in two different fuel oils. The results suggest that two types of COD are possible. One type exhibits complex rheological properties at low shear rates and does not produce a coal sediment, even after prolonged storage at 80/sup 0/C under dynamic conditions. The other exhibits near Newtonian behaviour and appears to form a sedimented layer of coal during storage.

On issue of increasing profitability of automated energy technology complexes for preparation and combustion of water-coal suspensions

Science.gov (United States)

Brylina, O. G.; Osintsev, K. V.; Prikhodko, YU S.; Savosteenko, N. V.

2018-03-01

The article considers the issues of energy technological complexes economy increase on the existing techniques of water-coal suspensions preparation and burning basis due to application of highly effective control systems of electric drives and neurocontrol. The automated control system structure for the main boiler components is given. The electric drive structure is disclosed by the example of pumps (for transfer of coal-water mash and / or suspension). A system for controlling and diagnosing a heat and power complex based on a multi-zone regulator is proposed. The possibility of using neural networks for implementing the control algorithms outlined in the article is considered.

Assessment of the radiation risk following from exploitation of Polish brown coals. Part 1. Brown coal in Polish industry; preparation of the method of determining the concentrations of main natural radioisotopes appearing in brown coal and its combustion products

International Nuclear Information System (INIS)

Jasinska, M.; Niewiadomski, T.; Schwabenthan, J.

1982-01-01

Poland is rich in deposits of brown coal applicable for large-scale industry. These deposits are estimated at about 13.5.10 9 tons. In the near future, one-half of the electric power produced in Poland will be generated by power plants using brown coal. As a result, the yearly burden of the environment in Poland will amount to about 15.10 6 tons of ashes and slag, and about 0.79.10 6 tons of fly ash emitted into the atmosphere. Concentrations of radioactive elements in wastes following from the use of brown coal may in some cases be as much as 12 times higher that occuring from combustion products of lignite coal. Distribution of these wastes to the environment affects the population, through inhalation of fly-ashes, consumption of radioactively contaminated products and through living in dwellings constructed of building materials produced using industrial wastes. In order to determine the concentrations of 226 Ra, 232 Th and 40 K in brown coal and in products of its combustion, the method of identifying these elements through gamma-spectrometry has been prepared. Concentrations of 210 Pb and 210 Po will be determined using the method of electrodeposition on metallic silver, which has been tested in the laboratory. (author)

Fiscal 2000 project on measures for assisting and diffusing environmentally-friendly coal utilization system introduction. CMG recovery/utilization system joint demonstration project; 2000 nendo kankyo chowagata sekitan riyo system donyu shien nado fukyu taisaku jigyo chosa hokoku. CMG kaishu riyo system kyodo jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

A CMG (coal mine gas) recovery/utilization system was designed, constructed, and then demonstrated at a model coal mining district in Liaoning Province for the purpose of contributing to the solution of energy and environment related problems in China. The recovery system demonstration test, aiming to improve on safety and productivity of coal mining and to supply recovered gas with stability, involved gas drainage test boring, mine sealing, sealed gas induction control, centralized gas monitoring, etc., which were carried out at the coal mine working face. A utilization system demonstration test was conducted, and CMG would continue to be supplied to the current users and CMG utilization would be started at the other 6 coal mines. For the supply of CMG to large-scale gas consuming areas, steel materials were manufactured and processed for spherical gas holders and denitrification facilities, gas holders were constructed, pipe lines were installed, and a provisional gas supply was carried out. For the transfer and diffusion of the technology, Chinese engineers were trained in Japan and Japanese engineers were dispatched to China. (NEDO)

Solids throttling valves for coal conversion and utilization development. Final report

Energy Technology Data Exchange (ETDEWEB)

Sine, G.C.

1980-11-01

A complete test system to test, evaluate, and develop control valves for slurry letdown service in coal liquefaction plants is needed. The site identified for the test system was the SRC II Pilot Plant located at Ft. Lewis, Washington. The US Department of Energy, Morgantown Energy Technology Center, requested a test system design that would enable testing of various configuration letdown valves that would be compatible with the existing facility and have minimum impact on Pilot Plant operations. Drawings and specifications for such a test system were prepared, coordinated with Ft. Lewis personnel, revised to reflect Ft. Lewis operating personnel comments, and approved for use by the Morgantown Energy Technology Center. These drawings and specifications will enable the test system to be built, installed, and integrated with the existing facility by a general contractor.

Underground Coal Thermal Treatment

Energy Technology Data Exchange (ETDEWEB)

Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Deo, M. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Sarofim, A. [Univ. of Utah, Salt Lake City, UT (United States); Gueishen, K. [Univ. of Utah, Salt Lake City, UT (United States); Hradisky, M. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States); Mandalaparty, P. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, H. [Univ. of Utah, Salt Lake City, UT (United States)

2012-01-11

The long-term objective of this work is to develop a transformational energy production technology by insitu thermal treatment of a coal seam for the production of substitute natural gas (SNG) while leaving much of the coal's carbon in the ground. This process converts coal to a high-efficiency, low-GHG emitting gas fuel. It holds the potential of providing environmentally acceptable access to previously unusable coal resources. This topical report discusses the development of experimental capabilities, the collection of available data, and the development of simulation tools to obtain process thermo-chemical and geo-thermal parameters in preparation for the eventual demonstration in a coal seam. It also includes experimental and modeling studies of CO₂ sequestration.

选煤厂数质量平衡管理的应用研究%Study on quantity and quality balance control in coal preparation plant

Institute of Scientific and Technical Information of China (English)

杜欣莉

2011-01-01

According to analyzing the technical process in Jinyang coal preparation plant, the best control points in the whole process were defined based on the quantity and quailty balance control principle of coal preparation products. All those improving methods can increase the total yield of coal preparation product, which means there will be a better economic benefits. It can get more accurate variable data and the management level is improved.%通过分析晋阳选煤厂工艺流程,根据洗选产品的数质量平衡原则确定了工序质量点,提出了强化生产过程数质量管理的思路,以保证洗选产品的综合产率,分析各计量数据的可靠性,提高企业的经营管理水平和经济效益.

Coal and coke applied to metallurgy. Vol. 2. Carvao e coque aplicados a metalurgia

Energy Technology Data Exchange (ETDEWEB)

Masuda, H.

1983-01-01

Papers include: coking; control of pollution from coking plants; handling and storage of coal; preparation of coal for coking; politics of the supply of coal; coke for blast furnaces; selective preparation and briquetting of coal for coking; cooling and drying of coke; preheating of coal for coking; formed coke.

Fluidized bed selective pyrolysis of coal

Science.gov (United States)

Shang, Jer Y.; Cha, Chang Y.; Merriam, Norman W.

1992-01-01

The present invention discloses a process for the pyrolysis of coal which comprises the effective utilization of two zonal inclined fluidized beds, where said zones can be selectively controlled as to temperature and heating rate. The first zonal inclined fluidized bed serves as a dryer for crushed coal and additionally is controlled to selectively pyrolyze said coal producing substantially carbon dioxide for recycle use. The second zonal inclined fluidized bed further pyrolyzes the coal to gaseous, liquid and char products under controlled temperature and heating rate zones designed to economically integrate the product mix. The gas and liquid products are recovered from the gaseous effluent stream while the char which remains can be further treated or utilized in a subsequent process step.

The development of coal-based technologies for Department of Defense facilities: Phase 1 final report. Volume 1: Technical report

Energy Technology Data Exchange (ETDEWEB)

Miller, B.G.; Morrison, J.L.; Pisupati, S.V. [Pennsylvania State Univ., University Park, PA (United States). Energy and Fuels Research Center] [and others

1997-01-31

The first phase of a three-phase project investigating the development of coal-based technologies for Department of Defense facilities has been completed. The objectives of the project are to: decrease DOD`s dependence on foreign oil and increase its use of coal; promote public and private sector deployment of technologies for utilizing coal-based fuels in oil-designed combustion equipment; and provide a continuing environment for research and development of coal-based fuel technologies for small-scale applications at a time when market conditions in the US are not favorable for the introduction of coal-fired equipment in the commercial and industrial capacity ranges. The Phase 1 activities were focused on developing clean, coal-based combustion technologies for the utilization of both micronized coal-water mixtures (MCWMs) and dry, micronized coal (DMC) in fuel oil-designed industrial boilers. The specific objective in Phase 1 was to deliver fully engineered retrofit options for a fuel oil-designed watertube boiler located on a DOD installation to fire either MCWM or DMC. This was achieved through a project consisting of fundamental, pilot-sale, and demonstration-scale activities investigating coal beneficiation and preparation, and MCWM and DMC combustion performance. In addition, detailed engineering designs and an economic analysis were conducted for a boiler located at the Naval Surface Warfare Center, near Crane, Indiana. Results are reported on MCWM and DMC combustion performance evaluation; engineering design; and cost/economic analysis.

Rosebud SynCoal Partnership, SynCoal{reg_sign} demonstration technology update

Energy Technology Data Exchange (ETDEWEB)

Sheldon, R.W. [Rosebud SynCoal Partnership, Billings, MT (United States)

1997-12-31

An Advanced Coal Conversion Process (ACCP) technology being demonstrated in eastern Montana (USA) at the heart of one of the world`s largest coal deposits is providing evidence that the molecular structure of low-rank coals can be altered successfully to produce a unique product for a variety of utility and industrial applications. The product is called SynCoal{reg_sign} and the process has been developed by the Rosebud SynCoal Partnership (RSCP) through the US Department of Energy`s multi-million dollar Clean Coal Technology Program. The ACCP demonstration process uses low-pressure, superheated gases to process coal in vibrating fluidized beds. Two vibratory fluidized processing stages are used to heat and convert the coal. This is followed by a water spray quench and a vibratory fluidized stage to cool the coal. Pneumatic separators remove the solid impurities from the dried coal. There are three major steps to the SynCoal{reg_sign} process: (1) thermal treatment of the coal in an inert atmosphere, (2) inert gas cooling of the hot coal, and (3) removal of ash minerals. When operated continuously, the demonstration plant produces over 1,000 tons per day (up to 300,000 tons per year) of SynCoal{reg_sign} with a 2% moisture content, approximately 11,800b Btu/lb and less than 1.0 pound of SO{sub 2} per million Btu. This product is obtained from Rosebud Mine sub-bituminous coal which starts with 25% moisture, 8,600 Btu/lb and approximately 1.6 pounds of SO{sub 2} per million Btu.

Fiscal 1996 survey report on the environmentally friendly type coal utilization system feasibility study. Survey by region/industry in India; Kankyo chowagata sekitan riyo system kanosei chosa. Indo ni okeru sekitan riyo gaikyo chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

A survey was made in India which is a coal producing/consuming country following China in Asia and where coal is used for about 60% of the primary commercial energy. The survey was conducted on coal production/distribution/utilization and environmental issues, aiming at studying feasibility of introducing the environmentally friendly coal utilization system into every industry including the residential/commercial one, and at implementing a comprehensive master plan including Japan`s international cooperation. Total power source facilities in fiscal 1995 are 83.3 million kW, 64% of which are coal thermal power facilities and generated 260 TWh, 69% of the total output energy. Main commercial energy sources are coal, oil and natural gas, and oil is self-sufficient. The survey this time did not examine very well the actual state of the environmental pollution problem caused by the coal utilization. Indian coal is high in ash content but low in sulfur content, and therefore, SOx polluting air has not been a very important problem so far, but soot/smoke is almost the problem. Further, ash treatment after combustion at boilers, etc. is expected to be a big problem in the future. 49 figs., 88 tabs.

Wabash River Coal Gasification Combined Cycle Repowering Project: Clean Coal Technology Program

International Nuclear Information System (INIS)

1993-05-01

The proposed project would result in a combined-cycle power plant with lower emissions and higher efficiency than most existing coal-fired power plants of comparable size. The net plant heat rate (energy content of the fuel input per useable electrical generation output; i.e., Btu/kilowatt hour) for the new repowered unit would be a 21% improvement over the existing unit, while reducing SO 2 emissions by greater than 90% and limiting NO x emissions by greater than 85% over that produced by conventional coal-fired boilers. The technology, which relies on gasified coal, is capable of producing as much as 25% more electricity from a given amount of coal than today's conventional coal-burning methods. Besides having the positive environmental benefit of producing less pollutants per unit of power generated, the higher overall efficiency of the proposed CGCC project encourages greater utilization to meet base load requirements in order to realize the associated economic benefits. This greater utilization (i.e., increased capacity factor) of a cleaner operating plant has global environmental benefits in that it is likely that such power would replace power currently being produced by less efficient plants emitting a greater volume of pollutants per unit of power generated

Graphene quantum dots, graphene oxide, carbon quantum dots and graphite nanocrystals in coals

Science.gov (United States)

Dong, Yongqiang; Lin, Jianpeng; Chen, Yingmei; Fu, Fengfu; Chi, Yuwu; Chen, Guonan

2014-06-01

Six coal samples of different ranks have been used to prepare single-layer graphene quantum dots (S-GQDs). After chemical oxidation and a series of centrifugation separation, every coal could be treated into two fractions, namely, CoalA and CoalB. According to the characterization results of TEM, AFM, XRD, Raman and FTIR, CoalA was revealed to be mainly composed of S-GQDs, which have an average height of about 0.5 nm and an average plane dimension of about 10 nm. The obtained S-GQDs showed excitation-dependent fluorescence and excellent electrochemiluminescence. CoalB was found to be some other carbon-based nanomaterials (CNMs), including agglomerated GQDs, graphene oxide, carbon quantum dots and agglomerated carbon nanocrystals. Generally, low-ranked coals might be more suitable for the preparation of S-GQDs. The production yield of S-GQDs from the six investigated coals decreased from 56.30% to 14.66% when the coal rank increased gradually. In contrast, high-ranked coals had high production yield of CoalB and might be more suitable for preparing other CNMs that were contained in CoalB, although those CNMs were difficult to separate from each other in our experiment.Six coal samples of different ranks have been used to prepare single-layer graphene quantum dots (S-GQDs). After chemical oxidation and a series of centrifugation separation, every coal could be treated into two fractions, namely, CoalA and CoalB. According to the characterization results of TEM, AFM, XRD, Raman and FTIR, CoalA was revealed to be mainly composed of S-GQDs, which have an average height of about 0.5 nm and an average plane dimension of about 10 nm. The obtained S-GQDs showed excitation-dependent fluorescence and excellent electrochemiluminescence. CoalB was found to be some other carbon-based nanomaterials (CNMs), including agglomerated GQDs, graphene oxide, carbon quantum dots and agglomerated carbon nanocrystals. Generally, low-ranked coals might be more suitable for the preparation of

The directory of United States coal & technology export resources. Profiles of domestic US corporations, associations and public entities, nationwide, which offer products or services suitable for export, relating to coal and its utilization

Energy Technology Data Exchange (ETDEWEB)

1994-01-01

The purpose of this directory is to provide a listing of available U.S. coal and coal related resources to potential purchasers of those resources abroad. The directory lists business entities within the US which offer coal related resources, products and services for sale on the international market. Each listing is intended to describe the particular business niche or range of product and/or services offered by a particular company. The listing provides addresses, telephones, and telex/fax for key staff in each company committed to the facilitation of international trade. The content of each listing has been formulated especially for this directory and reflects data current as of the date of this edition. The directory listings are divided into four primary classifications: coal resources; technology resources; support services; and financing and resource packaging. The first three of which are subdivided as follows: Coal Resources -- coal derivatives, coal exporters, and coal mining; Technology Resources -- advanced utilization, architects and engineers, boiler equipment, emissions control and waste disposal systems, facility construction, mining equipment, power generation systems, technical publications, and transport equipment; Support Services -- coal transport, facility operations, freight forwarders, sampling services and equipment, and technical consultants. Listings for the directory were solicited on the basis of this industry breakdown. Each of the four sections of this directory begins with a matrix illustrating which companies fall within the particular subclassifications specific to that main classification. A general alphabetical index of companies and an index by product/service classification are provided following the last section of the directory.

Panel reports of the first session of the workshop on coal for California

Energy Technology Data Exchange (ETDEWEB)

Davidson, Karen R.

1980-05-01

The panel reports are the result of a five-day workshop held at the Pajaro Dunes Conference Center, Watsonville, California, October 1-6, 1978. The workshop was conducted by JPL, under the sponsorship of the US Department of Energy and the California Energy Commission. The purpose of the exercise was to assay the opinions of a broad range of groups in order to identify what people perceive to be the problems associated with increased coal use in California. Representatives from utilities, industry, mining companies, citizens groups, and the academic community were divided into seven panels, each of which prepared a report. Representatives of government agencies attended as observers. The panels examined end-uses of coal in California, mine-mouth conversion, advanced concepts and use of Alaskan coal, environmental effects, public acceptance, finance, and legislation and regulation.

Production of blast furnace coke from soft brown coal

Energy Technology Data Exchange (ETDEWEB)

Scholz, G.; Wundes, H.; Schkommodau, F.; Zinke, H.-G. (VEB Gaskombinat Schwarze Pumpe (German Democratic Republic))

1988-01-01

Reviews experimental production and utilization of high quality brown coal coke in the GDR during 1985 and 1986. The technology of briquetting and coking brown coal dust is described; the superior parameters of produced coke quality are listed in comparison to those of regular industrial coke made from brown and black coal. Dust emission from high quality brown coal coke was suppressed by coke surface treatment with dispersion foam. About 4,200 t of this coke were employed in black coal coke substitution tests in a blast furnace. Substitution rate was 11%, blast furnace operation was positive, a substitution factor of 0.7 t black coal coke per 1 t of brown coal coke was calculated. Technology development of high quality brown coal coke production is regarded as complete; blast furnace coke utilization, however, requires further study. 8 refs.

Studies of the fate of sulfur trioxide in coal-fired utility boilers based on modified selected condensation methods.

Science.gov (United States)

Cao, Yan; Zhou, Hongcang; Jiang, Wu; Chen, Chien-Wei; Pan, Wei-Ping

2010-05-01

The formation of sulfur trioxide (SO(3)) in coal-fired utility boilers can have negative effects on boiler performance and operation, such as fouling and corrosion of equipment, efficiency loss in the air preheater (APH), increase in stack opacity, and the formation of PM(2.5). Sulfur trioxide can also compete with mercury when bonding with injected activated carbons. Tests in a lab-scale reactor confirmed there are major interferences between fly ash and SO(3) during SO(3) sampling. A modified SO(3) procedure to maximize the elimination of measurement biases, based on the inertial-filter-sampling and the selective-condensation-collecting of SO(3), was applied in SO(3) tests in three full-scale utility boilers. For the two units burning bituminous coal, SO(3) levels starting at 20 to 25 ppmv at the inlet to the selective catalytic reduction (SCR), increased slightly across the SCR, owing to catalytic conversion of SO(2) to SO(3,) and then declined in other air pollutant control device (APCD) modules downstream to approximately 5 ppmv and 15 ppmv at the two sites, respectively. In the unit burning sub-bituminous coal, the much lower initial concentration of SO(3) estimated to be approximately 1.5 ppmv at the inlet to the SCR was reduced to about 0.8 ppmv across the SCR and to about 0.3 ppmv at the exit of the wet flue gas desulfurization (WFGD). The SO(3) removal efficiency across the WFGD scrubbers at the three sites was generally 35% or less. Reductions in SO(3) across either the APH or the dry electrostatic precipitator (ESP) in units burning high-sulfur bituminous coal were attributed to operating temperatures being below the dew point of SO(3).

Froth flotation as a promising method of coal preparation in Brazil

Energy Technology Data Exchange (ETDEWEB)

Campos, A.R. de; Almeida, S L.M. de; Santos, A.T. dos

1979-01-01

Run-of-mine coal and pre-washed coal from Santa Catarina, Brazil, were characterized using washability curves, and by particle analysis after crushing. Bench-scale froth flotation tests were then conducted with the pre-washed coal, using kerosene and diesel oil as the collectors and pine oil as the frother. The influence of starch (as depressor) on flotation was also studied. The effects of feed particle size; pH; collector, frother and depressor additions; and flotation time were investigated. A 9.5% ash content coal was obtained with a mass recovery of about 29%. (17 refs.)

Fiscal 1999 report on basic research for promotion of joint implementation programs. Research on collection and utilization of coal mine methane gas in Russia (Kuznetsk coal field); Russia (Kuznetsk tanden) ni okeru tanko methane gas kaishu riyo chosa hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

The above-mentioned effort is to comply with the COP3 (Third Session of the Conference of the Parties to the United Nations Framework Convention on Climate Change) joint implementation clause. At this coal field, mining facilities are growing superannuated and obsolescent in the prolonged business depression, causing frequent occurrence of disasters such as gas explosions. The coal mine gas collection rate at the Kuznetsk coal field is as low as 17%, with concern for safety discouraging sufficient collection. Even the small amount of the collected gas is, in the absence of gas utilizing facilities, totally discharged into the air. For the mitigation of global warming, for mining safety, and for the establishment of a foundation for business, it is desired that coal mine methane gas collection/utilization facilities and related technologies be introduced into the coal field. Gas purging from the pits is incomplete, which is attributed to the lack of equipment capable of excavating proper-diameter bores longer than 100m for longwall mining. Ventilation also needs improvement. The research is under way on the premise that highly reliable intermediate range (300m) boring equipment and gas management technologies will be available. Collection of gas of a 30-35% concentration level at a collection rate of 40% is the target. (NEDO)

Coal chemical industry and its sustainable development in China

International Nuclear Information System (INIS)

Xie, Kechang; Li, Wenying; Zhao, Wei

2010-01-01

China is rich in coal resource, which is vital for energy security in this country. In early 21st century, the coal chemical industry in China will be oriented to the development of high efficiency, safety, cleanliness, and optimum utilization. In this review, the authors present an introduction to the utilization status of primary energy production and consumption in China. Since 2005, fundamental research studies, supported by the Ministry of Science and Technology of Chinese National Basic Research Program, have been carried out at Taiyuan University of Technology. The Ministry stresses that the new coal chemical industry should be developed in a sustainable manner to realize effective utilization of energy. Moreover, upgrading the high technology to improve actively the recycling processes of coal chemical engineering is of strategic importance to realize the modern coal chemical engineering.

Development of a Coal Quality Expert

Energy Technology Data Exchange (ETDEWEB)

None

1998-06-20

ABB Power Plant Laboratories Combustion Engineering, Inc., (ABB CE) and CQ Inc. completed a broad, comprehensive program to demonstrate the economic and environmental benefits of using higher quality U.S. coals for electrical power generation and developed state-of-the-art user-friendly software--Coal Quality Expert (CQE)-to reliably predict/estimate these benefits in a consistent manner. The program was an essential extension and integration of R and D projects performed in the past under U.S. DOE and EPRI sponsorship and it expanded the available database of coal quality and power plant performance information. This software will permit utilities to purchase the lowest cost clean coals tailored to their specific requirements. Based on common interest and mutual benefit, the subject program was cosponsored by the U.S. DOE, EPRI, and eight U.S. coal-burning utilities. In addition to cosponsoring this program, EPN contributed its background research, data, and computer models, and managed some other supporting contracts under the terms of a project agreement established between CQ Inc. and EPRI. The essential work of the proposed project was performed under separate contracts to CQ Inc. by Electric Power Technologies (El?'T), Black and Veatch (B and V), ABB Combustion Engineering, Babcock and Wilcox (B and W), and Decision Focus, Inc. Although a significant quantity of the coals tied in the United States are now cleaned to some degree before firing, for many of these coals the residual sulfur content requires users to install expensive sulfur removal systems and the residual ash causes boilers to operate inefficiently and to require frequent maintenance. Disposal of the large quantities of slag and ash at utility plant sites can also be problematic and expensive. Improved and advanced coal cleaning processes can reduce the sulfur content of many coals to levels conforming to environmental standards without requiring post-combustion desulfurization systems. Also

Electrostatic beneficiation of coal

Energy Technology Data Exchange (ETDEWEB)

Mazumder, M.K.; Tennal, K.B.; Lindquist, D.

1994-10-01

Dry physical beneficiation of coal has many advantages over wet cleaning methods and post combustion flue gas cleanup processes. The dry beneficiation process is economically competitive and environmentally safe and has the potential of making vast amounts of US coal reserves available for energy generation. While the potential of the electrostatic beneficiation has been studied for many years in laboratories and in pilot plants, a successful full scale electrostatic coal cleaning plant has not been commercially realized yet. In this paper the authors review some of the technical problems that are encountered in this method and suggest possible solutions that may lead toward its full utilization in cleaning coal.

Viscoelasticity of various gel films prepared from solvent-soluble constituents in coal; Sekitanchu no yobai kayoseibun kara sakuseishita shushu no gel maku no nendansei

Energy Technology Data Exchange (ETDEWEB)

Takanohashi, T.; Isoda, S.; Doi, S.; Iino, M. [Tohoku University, Sendai (Japan). Institute for Chemical Reaction Science

1996-10-28

Viscoelasticity of gel films prepared from solvent-soluble constituents without ash of coal using the mixed solvent of carbon disulfide and N-methyl-2-pyrrolidinone (CS2-NMP) was measured to study the network structure of the constituents. In experiment, Upper Freeport coal and Zao Zhuang coal were used as specimens. Viscoelasticity of various gels with different weight fractions of solvent was measured by creep measurement under a fixed load and stress-strain analysis under variable loads. In the 2nd and 3rd creep measurements, although no large changes in elastic strain and viscoelastic strain were found, viscous strain gradually decreased with an increase in viscosity. In the case of small weight fraction of solvent, small viscous strain and viscoelastic strain were found, while slightly large elastic strain was found. It was thus suggested that this elastic strain is derived from not only physical cross-linked networks by coal-solvent interaction but also those by coal-coal interaction in polymer chains of coal itself. 9 refs., 4 figs., 1 tab.

Investigation on characterization of Ereen coal deposit

OpenAIRE

S. Jargalmaa; B. Purevsuren; Ya. Davaajav; B. Avid; B. Bat-Ulzii; B. Ochirhuyag

2016-01-01

The Ereen coal deposit is located 360 km west from Ulaanbaatar and 95 km from Bulgan town. The coal reserve of this deposit is approximately 345.2 million tons. The Ereen coal is used directly for the Erdenet power plant for producing of electricity and heat. The utilization of this coal for gas and liquid product using gasification and pyrolysis is now being considered. The proximate and ultimate analysis show that the Ereen coal is low rank D mark hard coal, which corresponds to subbitumino...

Analysis of material flow in a utillzation technology of low grade manganese ore and sulphur coal complementary

Science.gov (United States)

Wang, Bo-Zhi; Deng, Biao; Su, Shi-Jun; Ding, Sang-Lan; Sun, Wei-Yi

2018-03-01

Electrolytic manganese is conventionally produced through low-grade manganese ore leaching in SO2, with the combustion of high sulfur coal. Subsequently the coal ash and manganese slag, produced by the combustion of high sulfur coal and preparation of electrolytic manganese, can be used as raw ingredients for the preparation of sulphoaluminate cement. In order to realize the `coal-electricity-sulfur-manganese-building material' system of complementary resource utilization, the conditions of material inflow and outflow in each process were determined using material flow analysis. The material flow models in each unit and process can be obtained by analyzed of material flow for new technology, and the input-output model could be obtained. Through the model, it is possible to obtain the quantity of all the input and output material in the condition of limiting the quantity of a substance. Taking one ton electrolytic manganese as a basis, the quantity of other input material and cements can be determined with the input-output model. The whole system had thusly achieved a cleaner production level. Therefore, the input-output model can be used for guidance in practical production.

Utilization of coal fly ash in construction in relation to regulations within the framework of the Dutch Soil Protection Act

International Nuclear Information System (INIS)

van der Sloot, H.A.

1991-01-01

In 1987, the Dutch Government passed the Soil Protection Act. Within the framework of this act aiming at reduction of soil pollution by anthropogenic activities, a number of regulations will be enforced. One of these is the Regulation for Construction Materials, which is intended to control environmental impacts resulting from the utilization of industrial residues in construction. The regulation will apply to all conventional materials used in construction and raw materials derived from waste materials. For effective enforcement of this regulation by 1992, a full set of well documented procedures are needed to cover such aspects as sampling, storage, analysis of solids and liquids, leaching, and evaluation of test results. These procedures should ultimately be available as national (NEN), or preferably internationally (CEN, ISO), agreed standard protocols. A coherent program of projects has been started in 1990 in association with the Dutch Normalization Institute to generate these protocols and initiate the necessary research activities. As a result of the new regulations, initiatives have been taken to certify industrial residues for certain applications. The utilization of coal combustion residues in construction is governed by certificates. Thus, quality control at the utilities is an integral part of coal fly ash utilization and marketing. For public acceptance of utilization of these materials, quality control and certification is an essential element along with demonstrations of proper performance in practice

Upgraded Coal Interest Group -- A vision for coal-based power in 1999 and beyond

International Nuclear Information System (INIS)

Hughes, E.; Battista, J.; Stopek, D.; Akers, D.

1999-01-01

The US is at a critical junction. Global competition is now a reality for a large number of US businesses and, ultimately, almost all US businesses will compete to one degree or another in the global marketplace. Under these circumstances, maintaining and improving the standard of living of US citizens requires a plentiful supply of low-cost electric energy to reduce the cost of providing goods and services both in the US an abroad. At the same time, segments of the public demand increased environmental restrictions on the utility industry. If the electric utility industry is to successfully respond to the goals of reducing electricity costs, maintaining reliability, and reducing emissions, fuels technology research is critical. For coal-fired units, fuel cost typically represents from 60--70% of operating costs. Reducing fuel cost, reduces operating costs. This can provide revenue that could be used to finance emissions control systems or advanced type of boilers resulting from post-combustion research. At the same time, improving coal quality reduces emissions from existing boilers without the need for substantial capital investment by the utility. If quality improvements can be accomplished with little or no increase in fuel costs, an immediate improvement in emissions can be achieved without an increase in electricity costs. All of this is directly dependent on continued and expanded levels of research on coal with the cooperation and partnership between government and industry. The paper describes enhanced fuel technologies (use of waste coal, coal water slurries, biomass/composite fuels, improved dewatering technologies, precombustion control of HAPs, dry cleaning technologies, and international coal characterization) and enhanced emission control technologies

Separation of the constituents of coal

Energy Technology Data Exchange (ETDEWEB)

Betrand, M F

1938-12-06

A process is disclosed of separating, by means of dense aqueous solutions, the constituents of coal, isolated by preliminary crushing from each other and/or from barren and carbonaceous shales, comprising the addition to the washing water before treatment or during any stage of the preparation of the coal before separation, or to the dense separating solution of agents improving the wetting of the coal by water.

Certification of the contents (mass fraction) of carbon, hydrogen, nitrogen, chlorine, arsenic, cadmium, manganese, mercury, lead, selenium, vanadium and zinc in three coals. Gas coal CRM No. 180; Coking coal CRM No. 181; Steam coal CRM No. 182

Energy Technology Data Exchange (ETDEWEB)

Griepink, B; Colinet, E; Wilkinson, H C

1986-01-01

The report first describes the preparation of three coal reference materials: Gas coal (BCR No. 180), Coking coal (BCR No. 181) and Steam coal (BCR No. 182). It deals further with the homogeneity and stability tests for major, minor and trace components. The contents (mass fractions) of the elements: C, H, N, Cl, As, Cd, Mn, Hg, Pb, Se, V and Zn are certified. The analytical techniques used in the certification are summarised. All the individual results are given and recommendations for analysis are made.

Study of mobilization and speciation of trace elements in coal pyrolysis

International Nuclear Information System (INIS)

Ting, B.T.G.

1979-01-01

Various types of coal contain high levels of a number of trace elements. Little is known of the fates of these trace elements during the conversion of coal to liquid and gaseous products. Studies were undertaken of mobilization and speciation of trace elements in coal pyrolysis, one of the major coal conversion processes. The bituminous coal was pyrolyzed to produce liquid and gaseous products. The pyrolysis products were collected in traps in an inert gas stream. In addition mildly hydrogenated coal was prepared by mixing with tetralin, a hydrogen donor solvent, at boiling temperature. In order to characterize each element specifically during pyrolysis, base samples of coal and mildly hydrogenated coal (H-coal) were spiked with heavy metal sulfides, trace metals bound to partially oxidized coal (coal humates), and halide salts prior to carrying out pyrolysis. Eight elements were investigated in this research. They are As, Br, Cl, Co, Cr, Mn, Se, and V. Pre-spiked hydrogenated coal, i.e., pulverized coal spiked with halide salts and heavy metal sulfides then hydrogenated with tetralin, was prepared and studied for the fates of these elements during pyrolysis. Chlorinated and brominated coals were also prepared to compare the volatility differences between organically and inorganically bound halogens during the pyrolysis reaction. These products and the coal char residues were analyzed for the spiked elements mainly by neutron activation analysis for the spiked elements to determine their degree of volatility. Volatility and recovery (mass balance) will be discussed for those elements that appeared highly volatile during pyrolysis. In order to understand the halogenated compounds in the pyrolysis products, gas chromatograms were taken to the collected pyrolysis products of coal, hydrogenated coal, NaCl spiked coal, NaBr spiked coal, chlorinated coal, and brominated coal

Low-level radiation in coals utilized and ashes produced at New York State electric utilities

International Nuclear Information System (INIS)

Hornibrook, C.

1981-01-01

Eight coal-fired power plants in New York State were sampled for coal, fly ash and bottom ash. Samples were analyzed for uranium 238, uranium 235, uranium 234, thorium 232, thorium 230, radium 226, lead 210, polonium 210, radon 222. The leachate of six fly ash samples was analyzed for all of the above except radon 222. Some data on fly ash analysis are included

Clean coal technology roadmap: issues paper

Energy Technology Data Exchange (ETDEWEB)

Pearson, B. [Natural Resources Canada, Ottawa, ON (Canada). CANMET Energy Technology Centre

2003-07-01

The need for the Clean Coal Technology Roadmap is based on the climate change threat, Canada's commitment to the Kyoto protocol, and the need to keep options open in determining the future position of coal in Canada's energy mix. The current role of coal, issues facing coal-fired utilities, and greenhouse gas emission policies and environmental regulations are outlined. The IEA energy outlook (2002) and a National Energy Board draft concerning Canada's energy future are outlined. Environmental, market, and technical demands facing coal, technology options for existing facilities, screening new developments in technology, and clean coal options are considered. 13 figs. 5 tabs.

CVFA: Coal vendor financial advisor

International Nuclear Information System (INIS)

Goote, W.G.; Andersen, S.

1992-01-01

An expert system for determining coal vendor financial viability in fuel purchasing contracts at an electric utility is described. The system blends rules, data objects, and financial knowledge to provide a rational basis for accepting or rejecting coal contracts given the financial capability of the coal vendor. The discussion concludes with a critique of managerial issues in the development of the system and its use in decision making. 3 refs., 1 fig

Healy Clean Coal Project: Healy coal firing at TRW Cleveland Test Facility

Energy Technology Data Exchange (ETDEWEB)

Koyama, T.; Petrill, E.; Sheppard, D.

1991-08-01

A test burn of two Alaskan coals was conducted at TRW's Cleveland test facility in support of the Healy Clean Coal Project, as part of Clean Coal Technology III Program in which a new power plant will be constructed using a TRW Coal Combustion System. This system features ash slagging technology combined with NO{sub x} and SO{sub x} control. The tests, funded by the Alaska Industrial Development and Export Authority (AIDEA) and TRW, were conducted to verify that the candidate Healy station coals could be successfully fired in the TRW coal combustor, to provide data required for scale-up to the utility project size requirements, and to produce sufficient flash-calcined material (FCM) for spray dryer tests to be conducted by Joy/NIRO. The tests demonstrated that both coals are viable candidates for the project, provided the data required for scale-up, and produced the FCM material. This report describes the modifications to the test facility which were required for the test burn, the tests run, and the results of the tests.

Capital cost: high and low sulfur coal plants-1200 MWe. [High sulfur coal

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

This Commercial Electric Power Cost Study for 1200 MWe (Nominal) high and low sulfur coal plants consists of three volumes. The high sulfur coal plant is described in Volumes I and II, while Volume III describes the low sulfur coal plant. The design basis and cost estimate for the 1232 MWe high sulfur coal plant is presented in Volume I, and the drawings, equipment list and site description are contained in Volume II. The reference design includes a lime flue gas desulfurization system. A regenerative sulfur dioxide removal system using magnesium oxide is also presented as an alternate in Section 7 Volume II. The design basis, drawings and summary cost estimate for a 1243 MWe low sulfur coal plant are presented in Volume III. This information was developed by redesigning the high sulfur coal plant for burning low sulfur sub-bituminous coal. These coal plants utilize a mechanical draft (wet) cooling tower system for condenser heat removal. Costs of alternate cooling systems are provided in Report No. 7 in this series of studies of costs of commercial electrical power plants.

Environmental impact assessment for steeply dipping coal beds: North Knobs site

Energy Technology Data Exchange (ETDEWEB)

1978-11-08

The US Department of Energy is funding an underground coal gasification (UCG) project in steeply dipping coal beds (SDB), at North Knobs, about 8 miles west of Rawlins, Carbon County, Wyoming. The project is being conducted to determine the technical, economic and environmental viability of such a technology. The development of SDB is an interesting target for UCG since such beds contain coals not normally mineable economically by ordinary techniques. Although the underground gasification of SDB has not been attempted in the US, Soviet experience and theoretical work indicate that the gasification of SDB in place offers all the advantages of underground gasification of horizontal coal seams plus some unique characteristics. The steep angle of dip helps to channel the produced gases up dip to offtake holes and permits the ash and rubble to fall away from the reaction zone helping to mitigate the blocking of the reaction zone in swelling coals. The intersection of SDB with the surface makes the seam accessible for drilling and other preparation. The tests at the North Knobs site will consist of three tests, lasting 20, 80 and 80 days, respectively. A total of 9590 tons of coal is expected to be gasified, with surface facilities utilizing 15 acres of the total section of land. The environmental effects of the experiment are expected to be very small. The key environmental impact is potential groundwater contamination by reaction products from coal gasification. There is good evidence that the surrounding coal effectively blocks the migration of these contaminants.

Utilization of coal fired power plant by-products. Utilization of coal ash; Sekitan karyoku ni okeru fukusanbutsu no yuko riyo gijutsu. Sekitanbai no yuko riyo

Energy Technology Data Exchange (ETDEWEB)

Kishimoto, K. [The Federation of Electric Power Companies, Tokyo (Japan); Watanabe, M. [Electric Power Development Co. Ltd., Tokyo (Japan)

1997-11-05

The paper introduced the present situation and future task of the tackling with effective use of coal ash discharged from coal thermal power plants. Making the use of the characteristics, coal ash is mostly used in the fields of cement/concrete, civil engineering/construction, and agriculture/forestry/fisheries. In the case of using fly ash to concrete, the effects are the heightening of long-term strength, increase in workability, decrease in hydration heat, control of alkali aggregate reaction, etc. In the civil engineering/construction field, coal ash is allowed to be used for road bed material and mixed civil engineering material as road materials, for revetment back-filling material, soft ground surface layer treatment, soft ground/soil improvement materials, FGC deep layer mixing treatment process, SPC (sand compaction pile) material, etc. as earth work materials. Besides, it is used for light coarse aggregate, light sand, etc., as construction materials, for material substituting ceramics products, etc. as building materials, and for agricultural material, potassium silicate fertilizer and ocean structure in the agriculture/forestry/fisheries field. 4 refs., 2 tabs.

Bioconversion of Coal: Hydrologic indicators of the extent of coal biodegradation under different redox conditions and coal maturity, Velenje Basin case study, Slovenia

Science.gov (United States)

Kanduč, Tjaša; Grassa, Fausto; Lazar, Jerneja; Jamnikar, Sergej; Zavšek, Simon; McIntosh, Jennifer

2014-05-01

Underground mining of coal and coal combustion for energy has significant environmental impacts. In order to reduce greenhouse gas emissions, other lower -carbon energy sources must be utilized. Coalbed methane (CBM) is an important source of relatively low-carbon energy. Approximately 20% of world's coalbed methane is microbial in origin (Bates et al., 2011). Interest in microbial CBM has increased recently due to the possibility of stimulating methanogenesis. Despite increasing interest, the hydrogeochemical conditions and mechanisms for biodegradation of coal and microbial methane production are poorly understood. This project aims to examine geochemical characteristics of coalbed groundwater and coalbed gases in order to constrain biogeochemical processes to better understand the entire process of coal biodegradation of coal to coalbed gases. A better understanding of geochemical processes in CBM areas may potentially lead to sustainable stimulation of microbial methanogenesis at economical rates. Natural analogue studies of carbon dioxide occurring in the subsurface have the potential to yield insights into mechanisms of carbon dioxide storage over geological time scales (Li et al., 2013). In order to explore redox processes related to methanogenesis and determine ideal conditions under which microbial degradation of coal is likely to occur, this study utilizes groundwater and coalbed gas samples from Velenje Basin. Determination of the concentrations of methane, carbondioxide, nitrogen, oxygen, argon was performed with homemade NIER mass spectrometer. Isotopic composition of carbon dioxide, isotopic composition of methane, isotopic composition of deuterium in methane was determined with Europa-Scientific IRMS with an ANCA-TG preparation module and Thermo Delta XP GC-TC/CF-IRMS coupled to a TRACE GC analyzer. Total alkalinity of groundwater was measured by Gran titration. Major cations were analyzed by ICP-OES and anions by IC method. Isotopic composition of

US and world coal trade

Energy Technology Data Exchange (ETDEWEB)

Stevens, B

1988-07-01

This paper reviews the US's coal trade with other countries in the world. Despite being pressed to support domestic coal producers, US utilities are looking towards Colombia for more of their supplies. Whilst the amount of Colombian coal imported into the US is small, it is a combination of this and coal imported from Australia, Canada and China which is causing concern. Studies indicate that the volume of coal imported into the US may rise to 3 Mt/year within three years. Coal exports may suffer if Brazil bans the import of significant quantities of US coking coal in retaliation against American trade sanctions against Brazilian computer import barriers. Also, Romania is expected to impose tariffs on US imports which will have an impact on US coal exported to Romania. US remains the top coal exporter to the European Communities but its lead was cut back due to a big rise of Australian export. A portion of EC market has also been lost to the USSR and Poland. Meanwhile, Japan is resisting buying US's steam coal because it is too expensive.

New stage of clean coal technology in Japan; Clean coal technology no aratana tenkai ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Kawaguchi, Y [Agency of Natural Resources and Energy, Tokyo (Japan)

1996-09-01

The paper described the positioning and new development of clean coal technology. Coal is an important resource which supplies approximately 30% of the energy consumed in all the world. In the Asian/Pacific region, especially, a share of coal in energy is high, around 60% of the world, and it is indispensable to continue using coal which is abundantly reserved. Japan continues using coal as an important energy among petroleum substituting energies taking consideration of the global environment, and is making efforts for development and promotion of clean coal technology aiming at further reduction of environmental loads. Moreover, in the Asian region where petroleum depends greatly upon outside the region, it is extremely important for stabilization of Japan`s energy supply that coal producing countries in the region promote development/utilization of their coal resources. For this, it is a requirement for Japan to further a coal policy having an outlook of securing stable coal supply/demand in the Asian region. 6 figs., 2 tabs.

Taipower - latest projects to boost coal import levels

Energy Technology Data Exchange (ETDEWEB)

Hargreaves, D

1985-05-01

The activities are reviewd for Taipower, the state enterprise electrical power utility for Taiwan RC: its generating facilities and comparability; the status of major projects, especially the Taichung thermal project; the status of coal; coal burn performance; air pollution controls; coal ash performance; coal imports; transport logistics; including terminal facilities at the Taichung thermal power plant.

Surface chemical problems in coal flotation

Science.gov (United States)

Taylor, S. R.; Miller, K. J.; Deurbrouck, A. W.

1981-02-01

As the use of coal increases and more fine material is produced by mining and processing, the need for improved methods of coal beneficiation increases. While flotation techniques can help meet these needs, the technique is beset with many problems. These problems involve surface chemical and interfacial properties of the coal-mineral-water slurry systems used in coal flotation. The problems associated with coal flotation include non-selectivity, inefficient reagent utilization, and excessive variablity of results. These problems can be broadely classified as a lack of predictability. The present knowledge of coal flotation is not sufficient, in terms of surface chemical parameters, to allow prediction of the flotation response of a given coal. In this paper, some of the surface chemical properties of coal and coal minerals that need to be defined will be discussed in terms of the problems noted above and their impact on coal cleaning.

CoalVal-A coal resource valuation program

Science.gov (United States)

Rohrbacher, Timothy J.; McIntosh, Gary E.

2010-01-01

CoalVal is a menu-driven Windows program that produces cost-of-mining analyses of mine-modeled coal resources. Geological modeling of the coal beds and some degree of mine planning, from basic prefeasibility to advanced, must already have been performed before this program can be used. United States Geological Survey mine planning is done from a very basic, prefeasibility standpoint, but the accuracy of CoalVal's output is a reflection of the accuracy of the data entered, both for mine costs and mine planning. The mining cost analysis is done by using mine cost models designed for the commonly employed, surface and underground mining methods utilized in the United States. CoalVal requires a Microsoft Windows? 98 or Windows? XP operating system and a minimum of 1 gigabyte of random access memory to perform operations. It will not operate on Microsoft Vista?, Windows? 7, or Macintosh? operating systems. The program will summarize the evaluation of an unlimited number of coal seams, haulage zones, tax entities, or other area delineations for a given coal property, coalfield, or basin. When the reader opens the CoalVal publication from the USGS website, options are provided to download the CoalVal publication manual and the CoalVal Program. The CoalVal report is divided into five specific areas relevant to the development and use of the CoalVal program: 1. Introduction to CoalVal Assumptions and Concepts. 2. Mine Model Assumption Details (appendix A). 3. CoalVal Project Tutorial (appendix B). 4. Program Description (appendix C). 5. Mine Model and Discounted Cash Flow Formulas (appendix D). The tutorial explains how to enter coal resource and quality data by mining method; program default values for production, operating, and cost variables; and ones own operating and cost variables into the program. Generated summary reports list the volume of resource in short tons available for mining, recoverable short tons by mining method; the seam or property being mined

Clean Coal Day '93. Hokkaido Seminar; Clean Coal Day '93. Hokkaido Seminar

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-11-01

The titles of the lectures in this record are 1) Coal energy be friendly toward the earth, 2) Future development of coal-fired thermal power generation, 3) Current status of research and development of coalbed methane in the U.S., and 4) PFBC (pressurized fluidized bed combustion combined cycle) system. Under title 1), the reason is explained why coal is back as an energy source and is made much of. The actualities of coal being labelled as a dirty energy source are explained. The rapid growth of demand for coal in Asia is commented on and what is expected of clean coal technology is stated. Under title 2), it is predicted that atomic energy, LNG (liquefied natural gas), and coal will be the main energy sources for electric power in Japan. Under title 3), it is stated that 10% of America's total amount of methane production is attributable to coal mining, that methane is the cleanest of the hydrocarbon fuels although it is a pollution source from an environmental point of view, and that it is therefore reasonable to have its collection and utilization placed in the domain of clean coal technology. Under title 4), a PFBC system to serve as the No. 3 machine for the Tomahigashi-Atsuma power plant is described. (NEDO)

Fiscal 2000 project for promoting international cooperation. Survey report on preparation of technological information in APEC region (Upstream area: preparation of video for training); 2000 nendo kokusai kyoryoku suishin jigyo chosa hokokusho. APEC iki nai ni okeru gijutsu joho seibi ni kakawaru chosa (Joryu bunya - kenshu you video sakusei)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

With the purpose of spreading and promoting clean coal technology (CCT) in coal producing countries in the APEC region, videos for training use were prepared so as to contribute to the reduction in environmental problems through the introduction of the coal cleaning and wastewater treatment technologies used in Japanese mines. In the video, comparison is made between the untreated wastewater and cleaned water flowing in and out of a present coal-cleaning plant, with the purification ratio determined, recognisably showing the effect by the cleaning facilities, and introducing the type of equipment required to satisfy the standard under the regulation. Also introduced is a technology for utilizing sludge collected in a sedimentation pond and fly ash scavenged in a private power plant. The videotape was prepared for 40 reels in English, 40 in Chinese, and 20 in Indonesian. The video title is 'Environmental safeguard of coal cleaning plant', and the contents are the importance of wastewater treatment and measures against water pollution, wastewater treatment technology in Taiheiyo coal mines, and wastewater treatment technology in Ikeshima coal mines. (NEDO)

Preliminary assessment of the health and environmental effects of coal utilization in the midwest. Volume I. Energy scenarios, technology characterizations, air and water resource impacts, and health effects

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

An initial evaluation of the major health and environmental issues associated with increased coal use in the six midwestern states of Illinois, Indiana, Michigan, Minnesota, Ohio, and Wisconsin is presented. Using an integrated assessment approach, the evaluation proceeds from a base-line scenario of energy demand and facility siting for the period 1975 to 2020. Emphasis is placed on impacts from coal extraction, land reclamation, coal combustion for electrical generation, and coal gasification. The range of potential impacts and constraints is illustrated by a second scenario that represents an expected upper limit for coal utilization in Illinois. Included are: (1) a characterization of the energy demand and siting scenarios, coal related technologies, and coal resources, and (2) the related impacts on air quality, water availability, water quality, and human health.

Cooling Effect Analysis of Suppressing Coal Spontaneous Ignition with Heat Pipe

Science.gov (United States)

Zhang, Yaping; Zhang, Shuanwei; Wang, Jianguo; Hao, Gaihong

2018-05-01

Suppression of spontaneous ignition of coal stockpiles was an important issue for safe utilization of coal. The large thermal energy from coal spontaneous ignition can be viewed as the latent energy source to further utilize for saving energy purpose. Heat pipe was the more promising way to diffuse effectively concentrated energy of the coal stockpile, so that retarding coal spontaneous combustion was therefore highly desirable. The cooling mechanism of the coal with heat pipe was pursued. Based on the research result, the thermal energy can be transported from the coal seam to the surface continuously with the use of heat pipe. Once installed the heat pipes will work automatically as long as the coal oxidation reaction was happened. The experiment was indicated that it can significantly spread the high temperature of the coal pile.

Demonstration of SCR technology for the control of NOx emissions from high-sulfur coal-fired utility boilers

Energy Technology Data Exchange (ETDEWEB)

Hinton, W.S. [W.S. Hinton and Associates, Cantonment, FL (United States); Maxwell, J.D.; Healy, E.C.; Hardman, R.R. [Southern Company Services, Inc., Birmingham, AL (United States); Baldwin, A.L. [Dept. of Energy, Pittsburgh, PA (United States)

1997-12-31

This paper describes the completed Innovative Clean Coal Technology project which demonstrated SCR technology for reduction of flue gas NO{sub x} emissions from a utility boiler burning US high-sulfur coal. The project was sponsored by the US Department of Energy, managed and co-funded by Southern Company Services, Inc. on behalf of the Southern Company, and also co-funded by the Electric Power Research Institute and Ontario Hydro. The project was located at Gulf Power Company`s Plant Crist Unit 5 (a 75 MW tangentially-fired boiler burning US coals that had a sulfur content ranging from 2.5--2.9%), near Pensacola, Florida. The test program was conducted for approximately two years to evaluate catalyst deactivation and other SCR operational effects. The SCR test facility had nine reactors: three 2.5 MW (5,000 scfm), and operated on low-dust flue gas. The reactors operated in parallel with commercially available SCR catalysts obtained from suppliers throughout the world. Long-term performance testing began in July 1993 and was completed in July 1995. A brief test facility description and the results of the project are presented in this paper.

Environmental control implications of generating electric power from coal. Appendix B. Assessment of status of technology for solvent refining of coal. 1977 technology status report

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

This report reviews the technology and environmental impacts of the solvent refined coal process to produce clean solid fuel (SRC-I). Information on SRC-I pilot plant operation, process design, and economics is presented. A bibliography of current available literature in this technology area, divided into fourteen categories with abstracts of the references, is appended. The history, current operations, and future plans for the SRC pilot plants at Fort Lewis and Wilsonville are reviewed. Process data generated at these pilot plants for various coals are used as a basis for a conceptual commercial plant design with a capacity to process 20,000 tons per day (TPD) of prepared coal. Block flow diagrams, material balances, an energy balance, and a list of raw materials for the plant are also provided. Capital cost estimates for a 20,000 TPD coal feed plant derived from four prior economic studies range from $706 million to $1093 million in 1976 dollars. The annual net operating cost is estimated at $238.6 million (1976 dollars) and the average product cost at $2.71/MM Btu based on utility financing (equity 25:debt 75) with $25/ton as the delivered price of the dry coal. The report also discusses special technical considerations associated with some of the process operations and major equipment items and enumerates technical risks associated with the commercialization of the SRC-I process.

Annotated bibliography of coal in the Caribbean region. [Lignite

Energy Technology Data Exchange (ETDEWEB)

Orndorff, R.C.

1985-01-01

The purpose of preparing this annotated bibliography was to compile information on coal localities for the Caribbean region used for preparation of a coal map of the region. Also, it serves as a brief reference list of publications for future coal studies in the Caribbean region. It is in no way an exhaustive study or complete listing of coal literature for the Caribbean. All the material was gathered from published literature with the exception of information from Cuba which was supplied from a study by Gordon Wood of the US Geological Survey, Branch of Coal Resources. Following the classification system of the US Geological Survey (Wood and others, 1983), the term coal resources has been used in this report for reference to general estimates of coal quantities even though authors of the material being annotated may have used the term coal reserves in a similar denotation. The literature ranges from 1857 to 1981. The countries listed include Colombia, Mexico, Venezuela, Cuba, the Dominican Republic, Haiti, Jamaica, Puerto Rico, and the countries of Central America.

Black coal in Australia 1983-84: a statistical year book

Energy Technology Data Exchange (ETDEWEB)

1984-01-01

An annual publication containing comprehensive statistical details of the Australian black coal industry. Included are statistics on coal supply and disposal, production, plant and equipment, coal preparation, manpower, exports, coal consumption, resources. Maps are included, also tables showing supply and disposal, production figures, employees, exports, consumption etc.

Material balance in coal. 2. Oxygen determination and stoichiometry of 33 coals

International Nuclear Information System (INIS)

Volborth, A.; Miller, G.E.; Garner, C.K.; Jerabek, P.A.

1977-01-01

The chemical analysis of coal can be supplemented by the determination of oxygen in high and low temperature ash, in coal as received and in coal dried at 105 0 C. The rapid method utilizes fast-neutron activation. The reaction 16 O(n,p) 16 N and counting of the 6.1 and 7.1 MeV gammas of 7.3 second half-life are used. A specially designed dual transfer and simultaneous counting system gives very accurate results. Oxygen in 33 coals ranging from lignite to low volatile bituminous coal is determined and compared with ''oxygen by difference.'' Considerable discrepancies are observed. Better stoichiometric results are obtained if oxygen in coal ash, in wet coal and in the dried coal is determined. This permits the estimation of the true material balances using data of the ultimate and the proximate coal analysis. The oxygen determination provides the coal chemist with an accurate basis and can be used to rank coal. The summation of the percent of carbon, nitrogen, hydrogen, sulfur, and oxygen becomes more meaningful and some errors can be detected and the state of completeness of coal analysis thus evaluated. Total sulfur can be estimated and oxidation effects during drying can be detected. These affect the moisture determination. It appears that after more data are collected, the interpretation of solid fuel analyses may be facilitated and will be stoichiometrically more meaningful. It is shown that it may be possible to simplify the present time-consuming methods of coal analysis

ADVANCED MULTI-PRODUCT COAL UTILIZATION BY-PRODUCT PROCESSING PLANT

Energy Technology Data Exchange (ETDEWEB)

Robert Jewell; Thomas Robl; John Groppo

2005-03-01

The objective of the project is to build a multi-product ash beneficiation plant at Kentucky Utilities 2,200-MW Ghent Generating Station, located in Carroll County, Kentucky. This part of the study includes the examination of the feedstocks for the beneficiation plant. The ash, as produced by the plant, and that stored in the lower pond were examined. The ash produced by the plant was found to be highly variable as the plant consumes high and low sulfur bituminous coal, in Units 1 and 2 and a mixture of subbituminous and bituminous coal in Units 3 and 4. The ash produced reflected this consisting of an iron-rich ({approx}24%, Fe{sub 2}O{sub 3}), aluminum rich ({approx}29% Al{sub 2}O{sub 3}) and high calcium (6%-7%, CaO) ash, respectively. The LOI of the ash typically was in the range of 5.5% to 6.5%, but individual samples ranged from 1% to almost 9%. The lower pond at Ghent is a substantial body, covering more than 100 acres, with a volume that exceeds 200 million cubic feet. The sedimentation, stratigraphy and resource assessment of the in place ash was investigated with vibracoring and three-dimensional, computer-modeling techniques. Thirteen cores to depths reaching nearly 40 feet, were retrieved, logged in the field and transported to the lab for a series of analyses for particle size, loss on ignition, petrography, x-ray diffraction, and x-ray fluorescence. Collected data were processed using ArcViewGIS, Rockware, and Microsoft Excel to create three-dimensional, layered iso-grade maps, as well as stratigraphic columns and profiles, and reserve estimations. The ash in the pond was projected to exceed 7 million tons and contain over 1.5 million tons of coarse carbon, and 1.8 million tons of fine (<10 {micro}m) glassy pozzolanic material. The size, quality and consistency of the ponded material suggests that it is the better feedstock for the beneficiation plant.

Volcanic ash in feed coal and its influence on coal combustion products

Energy Technology Data Exchange (ETDEWEB)

Brownfield, M.E.; Affolter, R.H.; Cathcart, J.D.; Brownfield, I.K.; Hower, J.C.; Stricker, G.D.; O' Connor, J.T.

2000-07-01

The US Geological Survey and the University of Kentucky Center for Applied Energy Research are collaborating with an Indiana Utility to determine the physical and chemical properties of feed coal and coal combustion products (CCPs) from a coal-fired power plant. The plant utilizes a low-sulfur (.23--.47 weight percent S) coal from the Powder River Basin, Wyoming. Scanning Electron Microscope (SEM) and X-ray diffraction (XRD) analysis of feed coal samples identified two mineral suites. A primary suite (not authigenic) consisting of quartz (detrital and volcanic beta-form grains), biotite, and minor zircon and a secondary authigenic mineral suite containing calcite, alumino-phosphates (crandallite and gorceixite), kaolinite, quartz, anatase, barite, and pyrite. The authigenic minerals are attributed to air-fall and reworked volcanic ash that was deposited in peat-forming mires. The Powder River Basin feed coals contain higher amounts of Ba, Ca, Mg, Na, Sr, and P compared to other analyzed eastern coals. These elements are associated with alumino-phosphate, biotite, calcite, and clay minerals. The element associations are indicative of coal that incorporated volcanic ash during deposition. XRD analysis of CCPs revealed a predominance of glass, perovskite, lime, gehlenite, quartz, and phosphates with minor amounts of periclase, anhydrite, hematite, and spinel group minerals in the fly ash; and quartz, plagioclase (albite and anorthite), pyroxene (augite and fassaite), rhodonite, and akermanite in the bottom ash. Microprobe and SEM analysis of fly ash samples revealed quartz, zircon, monazite, euhedral laths of corundum with merrillite, hematite, dendritic spinels/ferrites, and rounded grains of wollastonite with periclase. The abundant Ca and Mg mineral phases in the fly ashes are related to the presence of carbonate, clay, and phosphate minerals in the feed coal. The Ca- and Mg-rich mineral phases in the CCPs can be attributed to volcanic minerals deposited in the

Method selection for mercury removal from hard coal

Directory of Open Access Journals (Sweden)

Dziok Tadeusz

2017-01-01

Full Text Available Mercury is commonly found in coal and the coal utilization processes constitute one of the main sources of mercury emission to the environment. This issue is particularly important for Poland, because the Polish energy production sector is based on brown and hard coal. The forecasts show that this trend in energy production will continue in the coming years. At the time of the emission limits introduction, methods of reducing the mercury emission will have to be implemented in Poland. Mercury emission can be reduced as a result of using coal with a relatively low mercury content. In the case of the absence of such coals, the methods of mercury removal from coal can be implemented. The currently used and developing methods include the coal cleaning process (both the coal washing and the dry deshaling as well as the thermal pretreatment of coal (mild pyrolysis. The effectiveness of these methods various for different coals, which is caused by the diversity of coal origin, various characteristics of coal and, especially, by the various modes of mercury occurrence in coal. It should be mentioned that the coal cleaning process allows for the removal of mercury occurring in mineral matter, mainly in pyrite. The thermal pretreatment of coal allows for the removal of mercury occurring in organic matter as well as in the inorganic constituents characterized by a low temperature of mercury release. In this paper, the guidelines for the selection of mercury removal method from hard coal were presented. The guidelines were developed taking into consideration: the effectiveness of mercury removal from coal in the process of coal cleaning and thermal pretreatment, the synergy effect resulting from the combination of these processes, the direction of coal utilization as well as the influence of these processes on coal properties.

Comparative study of coal and biomass co-combustion with coal burning separately through emissions analysis

International Nuclear Information System (INIS)

Siddique, M.; Asadullah, A.; Khan, G.; Soomro, S.A.

2016-01-01

Appropriate eco-friendly methos to mitigate the problem of emissions from combustion of fossil fuel are highly demanded. The current study was focused on the effect of using coal and coal biomass co-combustion on the gaseous emissions. Different biomass were used along with coal. The coal used was lignite coal and the biomass' were tree waste, cow dung and banana tree leaves Various ratios of coal and biomass were used to investigate the combustion behavior of coal cow dung and 100% banana tree leaves emits less emission of CO, CO/sub 2/, NOx and SO/sub 2/ as compared to 100% coal, Maximum amount of CO emission were 1510.5 ppm for bannana tree waste and minimum amount obtained for lakhra coal and cow dung manure (70:30) of 684.667 leaves (90:10) and minimum amount of SO/sub 2/ present in samples is in lakhra coal-banana tree waste (80:20). The maximum amount of NO obtained for banana tree waste were 68 ppm whereas amount from cow dung manure (30.83 ppm). The study concludes that utilization of biomass with coal could make remedial action against environment pollution. (author)

Inorganic Constituents in Coal

Directory of Open Access Journals (Sweden)

Rađenović A.

2006-02-01

Full Text Available Coal contains not only organic matter but also small amounts of inorganic constituents. More thanone hundred different minerals and virtually every element in the periodic table have been foundin coal. Commonly found group minerals in coal are: major (quartz, pyrite, clays and carbonates,minor, and trace minerals. Coal includes a lot of elements of low mass fraction of the orderof w=0.01 or 0.001 %. They are trace elements connected with organic matter or minerals comprisedin coal. The fractions of trace elements usually decrease when the rank of coal increases.Fractions of the inorganic elements are different, depending on the coal bed and basin. A varietyof analytical methods and techniques can be used to determine the mass fractions, mode ofoccurrence, and distribution of organic constituents in coal. There are many different instrumentalmethods for analysis of coal and coal products but atomic absorption spectroscopy – AAS is theone most commonly used. Fraction and mode of occurrence are one of the main factors that haveinfluence on transformation and separation of inorganic constituents during coal conversion.Coal, as an important world energy source and component for non-fuels usage, will be continuouslyand widely used in the future due to its relatively abundant reserves. However, there is aconflict between the requirements for increased use of coal on the one hand and less pollution onthe other. It’s known that the environmental impacts, due to either coal mining or coal usage, canbe: air, water and land pollution. Although, minor components, inorganic constituents can exert asignificant influence on the economic value, utilization, and environmental impact of the coal.

Effect of hydrothermal dewatering on the slurryability of brown coals

International Nuclear Information System (INIS)

Yu Yujie; Liu Jianzhong; Wang Ruikun; Zhou Junhu; Cen Kefa

2012-01-01

Highlights: ► Brown coals are upgraded by hydrothermal dewatering. ► The moisture content and oxygen functional groups decrease during the process. ► The point of zero charge and the contact angle rise as the temperature increases. ► The products were highly hydrophobic. ► The improvement on slurryability of solid products were examined. - Abstract: Two brown coals from China were dewatered under hydrothermal dewatering (HTD) conditions at 250–320 °C for 1 h in a 2 L autoclave. The hydrothermally dewatered products were used to prepare coal water slurry (CWS) with a lower viscosity than brown raw coal slurry. Moreover, the coal rank and heat value of the brown coal increased as the inherent moisture and oxygen content decreased during the HTD process. The maximum solid concentration of CWS prepared from XiMeng coal increased from 45.7% to 59.3%, whereas that of CWS prepared from BaoTou coal increased from 53.7% to 62.1%, after being dewatered at 320 °C. The improvement in the slurryability of brown coal significantly depended on the final temperature of the HTD process, the mechanism of which can be explained by the chemical analysis of oxygen functional groups, zeta potential, and the contact angle of the surface between coal and water. The oxygen functional groups, the oxygen/carbon ratio and hydrogen/carbon ratio in brown coal decreased, indicating that the coal rank was upgraded during the HTD process. As a result, both the point of zero charge and the contact angle increased, implying that the HTD products were highly hydrophobic.

Energy Policy Act transportation rate study: Interim report on coal transportation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The primary purpose of this report is to examine changes in domestic coal distribution and railroad coal transportation rates since enactment of the Clean Air Act Amendments of 1990 (CAAA90). From 1988 through 1993, the demand for low-sulfur coal increased, as a the 1995 deadline for compliance with Phase 1 of CAAA90 approached. The shift toward low-sulfur coal came sooner than had been generally expected because many electric utilities switched early from high-sulfur coal to ``compliance`` (very low-sulfur) coal. They did so to accumulate emissions allowances that could be used to meet the stricter Phase 2 requirements. Thus, the demand for compliance coal increased the most. The report describes coal distribution and sulfur content, railroad coal transportation and transportation rates, and electric utility contract coal transportation trends from 1979 to 1993 including national trends, regional comparisons, distribution patterns and regional profiles. 14 figs., 76 tabs.

Geological evaluation on productibility of coal seam gas; Coal seam gas no chishitsugakuteki shigen hyoka ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Fujii, K [University of Shizuoka, Shizuoka (Japan). Faculty of Education

1996-09-01

Coal seam gas is also called coal bed methane gas, indicating the gas existing in coal beds. The gas is distinguished from the oil field based gas, and also called non-conventional type gas. Its confirmed reserve is estimated to be 24 trillion m {sup 3}, with the trend of its development seen worldwide as utilization of unused resource. For the necessity of cultivating relevant technologies in Japan, this paper considers processes of production, movement, stockpiling, and accumulation of the gas. Its productibility is controlled by thickness of a coal bed, degree of coalification, gas content, permeability, groundwater flow, and deposition structure. Gas generation potential is evaluated by existing conditions of coal and degree of coalification, and methane production by biological origin and thermal origin. Economically viable methane gas is mainly of the latter origin. Evaluating gas reserve potential requires identification of the whole mechanism of adsorption, accumulation and movement of methane gas. The gas is expected of effect on environmental aspects in addition to availability as utilization of unused energy. 5 figs.

FY1995 development of economical and high efficient desulfurization process using low rank coal; 1995 nendo teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The objective of this study is to develop a new efficient desulfurization technique using a Ca ion-exchanged coal prepared from low rank coal and calcium raw material as a SO{sub 2} sorbent. Ion-exchange of calcium was carried out by soaking and mixing brown coal particles in milk of lime or slurry of industrial waste from concrete manufacture process. About 10wt% of Ca was easily incorporated into Yallourn coal. The ion-exchanged Ca was transformed to ultra-fine CaO particles upon pyrolysis of coal. The reactivity of CaO produced from Ca-exchanged coal to SO{sub 2} was extraordinary high and the CaO utilization of above 90% was easily achieved, while the conversion of natural limestone was less than 30% under the similar experimental conditions. High activity of Ca-exchanged coal was appreciably observed in a pressurized fluidized bed combustor. Ca-exchanged coal was quite effective for the removal of hydrogen sulfide. (NEDO)

Status of Westinghouse coal-fueled combustion turbine programs

International Nuclear Information System (INIS)

Scalzo, A.J.; Amos, D.J.; Bannister, R.L.; Garland, R.V.

1992-01-01

Developing clean, efficient, cost effective coal utilization technologies for future power generation is an essential part of our National Energy Strategy. Westinghouse is actively developing power plants utilizing advanced gasification, atmospheric fluidized beds (AFB), pressurized fluidized beds (PFB), and direct firing technology through programs sponsored by the U.S. Dept. of Energy (DOE). The DOE Office of Fossil Energy is sponsoring the Direct Coal-Fired Turbine program. This paper presents the status of current and potential Westinghouse Power Generation Business Unit advanced coal-fueled power generation programs as well as commercial plans

Preparation of Active Absorbent for Flue Gas Desulfurization From Coal Bottom Ash: Effect of Absorbent Preparation Variables

Directory of Open Access Journals (Sweden)

Chang Chin Li, Lee Keat Teong, Subhash Bhatia and Abdul Rahman Mohamed

2012-08-01

Full Text Available An active absorbent for flue gas desulfurization was prepared from coal bottom ash, calcium oxide (CaO and calcium sulfate by hydro-thermal process. The absorbent was examined for its micro-structural properties. The experiments conducted were based on Design Of Experiments (DOE according to 23 factorial design. The effect of various absorbent preparation variables such as ratio of CaO to bottom ash (A, hydration temperature (B and hydration period (C towards the BET (Brunauer-Emmett-Teller specific surface area of the absorbent were studied. At a CaO to bottom ash ratio = 2, hydration temperature = 200 ?C and hydration period = 10 hrs, absorbent with a surface area of 90.1 m2/g was obtained. Based on the analysis of the factorial design, it was concluded that factor A and C as well as the interaction of factors ABC and BC are the significant factors that effect the BET surface area of the absorbent. A linear mathematical model that describes the relation between the independent variables and interaction between variables towards the BET specific surface area of the absorbent was also developed. Analysis of variance (ANOVA showed that the model was significant at 1% level.Key Words: Absorbent, Bottom Ash, Design Of Experiments, Desulfurization, Surface Area.

Characterization and supply of coal-based fuels

Energy Technology Data Exchange (ETDEWEB)

1989-06-01

Contract objectives are as follows: Develop fuel specifications to serve combustor requirements. Select coals having appropriate compositional and quality characteristics as well as an economically attractive reserve base; Provide quality assurance for both the parent coals and the fuel forms; and deliver premium coal-based fuels to combustor developers as needed for their contract work. Progress is discussed, particulary in slurry fuel preparation and particle size distribution.

China’s farewell to coal: A forecast of coal consumption through 2020

International Nuclear Information System (INIS)

Hao, Yu; Zhang, Zong-Yong; Liao, Hua; Wei, Yi-Ming

2015-01-01

In recent decades, China has encountered serious environmental problem, especially severe air pollution that has affected eastern and northern China frequently. Because most air pollutants in China are closely related to coal combustion, the restriction of coal consumption is critical to the improvement of the environment in China. In this study, a panel of 29 Chinese provinces from 1995 to 2012 is utilized to predict China’s coal consumption through 2020. After controlling for the spatial correlation of coal consumption among neighboring provinces, an inverted U-shaped Environmental Kuznets Curve (EKC) between coal consumption per capita and GDP per capita in China is detected. Furthermore, based on the estimation results and reasonable predictions of key control variables, China’s provincial and national coal consumption through 2020 is forecasted. Specifically, under the benchmark scenario, consumption is expected to continue growing at a decreasing rate until 2020, when China’s coal consumption would be approximately 4.43 billion tons. However, if China can maintain relatively high growth rate (an annual growth rate of 7.8 percent), the turning point in total coal consumption would occur in 2019, with projected consumption peaking at 4.16 billion tons. - Highlights: • Provincial panel data is used to investigate the influential factors of coal consumption in China. • The spatial correlations of coal consumption in neighboring provinces are fully considered. • An inverted-U shaped Environmental Kuznets Curve for coal consumption in China has been found. • Based on the estimation results, China’s national coal consumption before 2020 is forecasted. • Under the basic scenario, China’s national coal consumption will grow at a decreasing speed till 2020.

Energy Information Administration quarterly coal report, October--December 1992

International Nuclear Information System (INIS)

1993-01-01

The United States produced just over 1 billion short tons of coal in 1992, 0.4 percent more than in 1991. Most of the 4-million-short-ton increase in coal production occurred west of the Mississippi River, where a record level of 408 million short tons of coal was produced. The amount of coal received by domestic consumers in 1992 totaled 887 million short tons. This was 7 million short tons more than in 1991, primarily due to increased coal demand from electric utilities. The average price of delivered coal to each sector declined by about 2 percent. Coal consumption in 1992 was 893 million short tons, only 1 percent higher than in 1991, due primarily to a 1-percent increase in consumption at electric utility plants. Consumer coal stocks at the end of 1992 were 163 million short tons, a decrease of 3 percent from the level at the end of 1991, and the lowest year-end level since 1989. US coal exports fell 6 percent from the 1991 level to 103 million short tons in 1992. Less coal was exported to markets in Europe, Asia, and South America, but coal exports to Canada increased 4 million short tons

Tenth annual coal preparation, utilization, and environmental control contractors conference: Proceedings. Volume 2

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

Volume II contains papers presented at the following sessions: combustion 2000 session; advanced research and technology development session; commercial/industrial combustion systems session; alternative fuels utilization session; environmental control poster session; and advanced combustion technology poster session. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

Microbial diversity of western Canadian subsurface coal beds and methanogenic coal enrichment cultures

Energy Technology Data Exchange (ETDEWEB)

Penner, Tara J.; Foght, Julia M. [Department of Biological Sciences, University of Alberta, Edmonton, Alberta (Canada); Budwill, Karen [Carbon and Energy Management, Alberta Innovates-Technology Futures, 250 Karl Clark Road, Edmonton, Alberta (Canada)

2010-05-01

Coalbed methane is an unconventional fuel source associated with certain coal seams. Biogenic methane can comprise a significant portion of the gas found in coal seams, yet the role of microbes in methanogenesis in situ is uncertain. The purpose of this study was to detect and identify major bacterial and archaeal species associated with coal sampled from sub-bituminous methane-producing coal beds in western Canada, and to examine the potential for methane biogenesis from coal. Enrichment cultures of coal samples were established to determine how nutrient amendment influenced the microbial community and methane production in the laboratory. 16S rRNA gene clone libraries were constructed using DNA extracted and amplified from uncultured coal samples and from methanogenic coal enrichment cultures. Libraries were screened using restriction fragment length polymorphism, and representative clones were sequenced. Most (> 50%) of the bacterial sequences amplified from uncultured coal samples were affiliated with Proteobacteria that exhibit nitrate reduction, nitrogen fixation and/or hydrogen utilization activities, including Pseudomonas, Thauera and Acidovorax spp., whereas enrichment cultures were dominated by Bacteroidetes, Clostridia and/or Lactobacillales. Archaeal 16S rRNA genes could not be amplified from uncultured coal, suggesting that methanogens are present in coal below the detection levels of our methods. However, enrichment cultures established with coal inocula produced significant volumes of methane and the archaeal clone libraries were dominated by sequences closely affiliated with Methanosarcina spp. Enrichment cultures incubated with coal plus organic nutrients produced more methane than either nutrient or coal supplements alone, implying that competent methanogenic consortia exist in coal beds but that nutrient limitations restrict their activity in situ. This report adds to the scant literature on coal bed microbiology and suggests how microbes may be

Survey of trace elements in coals and coal-related materials by neutron activation analysis

International Nuclear Information System (INIS)

Ruch, R.R.; Cahill, R.A.; Frost, J.K.; Camp, L.R.; Gluskoter, H.J.

1977-01-01

Utilizing primarily instrumental neutron activation analysis and other analytical methods such as neutron-activation analysis with radiochemical separation, emission spectrochemical analysis, atomic absorption spectroscopy, X-ray fluorescence analysis, ion-selective electrode analysis, and American Society for Testing of Materials procedures (ASTM), as many as 61 elements were quantitatively surveyed in 170 U.S. whole coals, 70 washed coals, and 40 bench samples. Data on areal and vertical distributions in various regions were obtained along with extensive information on the mode of occurence of various elements in the coal matrix itself. Efforts have been made to attain the maximal accuracy and precision possible for a wide variety of elements in the inhomogeneous coal matrix. (T.G.)

Coal and public perceptions

International Nuclear Information System (INIS)

Porter, R.C.

1993-01-01

The Department of Energy's (DOE) clean coal outreach efforts are described. The reason why clean coal technology outreach must be an integral part of coal's future is discussed. It is important that we understand the significance of these advances in coal utilization not just in terms of of hardware but in terms of public perception. Four basic premises in the use of coal are presented. These are: (1) that coal is fundamentally important to this nation's future; (2) that, despite premise number 1, coal's future is by no means assured and that for the last 10 years, coal has been losing ground; (3) that coal's future hinges on the public understanding of the benefits of the public's acceptance of advanced clean coal technology; and (4) hat public acceptance of clean coal technology is not going to be achieved through a nationwide advertising program run by the Federal government or even by the private sector. It is going to be gained at the grassroots level one community at a time, one plant at a time, and one referendum at a time. The Federal government has neither the resources, the staff, nor the mandate to lead the charge in those debates. What is important is that the private sector step up to the plate as individual companies and an individual citizens working one-one-one at the community level, one customer, one civic club, and one town meeting at a time

Report on investigations in fiscal 2000 on the projects to support introduction of environment friendly coal utilization system. Green helmet project for briquette production plant - Mae Moh coal mine, Thailand; 2000 nendo kankyo chowagata sekitan riyo system donyu shien jigyo chosa hokokusho. Briquette seizo setsubi ni kakawaru green helmet jigyo (Thai koku Mae Moh tanko)

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-06-01

This Green Helmet Project is intended to suppress generation of environment polluting substances in association with coal utilization in Thailand by demonstrating and improving the proliferation infrastructure for the clean coal technology to be used widely in Thailand. The project is also intended to serve for stabilized assurance of energies for Japan. The demonstration project related to briquette manufacturing facilities executed as one of the 'Projects to support introduction of environment friendly coal utilization system' is intended to manufacture at low cost a briquette which is low in odor, free of smoke, and suppressed largely of sulfur oxide generation. The briquette is made by adding clayish minerals, sulfur, a fixing agent and a binder into brown coal being a low grade coal. The project implements proliferation of the technology to reduce environmental load associated with coal utilization in developing countries according to the situation and needs of the counterpart countries. The present project has performed the site surveys and guidance of operation and maintenance techniques as follow-up works of the demonstration project having been completed by cooperation between Japan and Thailand. It is considered that what had been intended in the beginning has been achieved sufficiently. (NEDO)

Low-rank coal study. Volume 4. Regulatory, environmental, and market analyses

Energy Technology Data Exchange (ETDEWEB)

1980-11-01

The regulatory, environmental, and market constraints to development of US low-rank coal resources are analyzed. Government-imposed environmental and regulatory requirements are among the most important factors that determine the markets for low-rank coal and the technology used in the extraction, delivery, and utilization systems. Both state and federal controls are examined, in light of available data on impacts and effluents associated with major low-rank coal development efforts. The market analysis examines both the penetration of existing markets by low-rank coal and the evolution of potential markets in the future. The electric utility industry consumes about 99 percent of the total low-rank coal production. This use in utility boilers rose dramatically in the 1970's and is expected to continue to grow rapidly. In the late 1980's and 1990's, industrial direct use of low-rank coal and the production of synthetic fuels are expected to start growing as major new markets.

Coal business heats up in the US

Energy Technology Data Exchange (ETDEWEB)

Mohan, M. [CN Rail (United States)

2002-03-01

The fact that CN's Coal Business Unit moved just under 50 million t of coal in 2001 would have been unimaginable just a year earlier, as CN's coal franchise faced a number of challenges last year. On the metallurgical side, where bituminous coal is used in steel production, rising extraction costs in relation to national and international values forced the closure of three CN-served mines in 2000: TeckCominco's Quinteet mine in British Columbia; Smoky River Coal's Smoky River facility and Luscar's Gregg River mine, Alberta. As for thermal coal, utilities had been moving to alternative fuels, maintaining only low coal inventories, and there were few plans for new coal plants. The article explains how North America's railroad helps fuel growing demand for thermal and metallurgical coal. 5 photos.

Feedlot biomass co-firing: a renewable energy alternative for coal-fired utilities. Paper no. IGEC-1-128

International Nuclear Information System (INIS)

Arumugam, S.; Thien, B.; Annamalai, K.; Sweeten, J.

2005-01-01

The swiftly growing feedlot industry in the United States upshots in the production of manure from one or more animal species in excess of what can safely be applied to farmland in accordance with nutrient management plans. Disposal of the vast quantity of manure produced as a by-product of the cattle feeding industry is one of the major operating tasks of the industry. Aside from the traditional means of disposal as fertilizer, an alternative and attractive way of overcoming this threat is to develop processes that make use of manure as an energy resource. In the present study, the feasibility of using of manure as a fuel in existing coal fired power plants is considered and appropriately termed Feedlot Biomass (FB). The technology of co-firing coal: feedlot biomass facilitates an environment friendly utilization of animal waste for the production of valuable power/steam concurrently addressing the renewable energy, groundwater contamination, and greenhouse gas concerns. Co-firing tests were performed at the Texas AandM University 30 kW t (100,000 Btu/h) laboratory-scale facility. The trials revealed the enhanced combustion of the blends. The NO emissions were less for the blend even with higher nitrogen content of FB as compared to coal. (author)

Coal use in the People`s Republic of China, Volume 2: The economic effects of constraining coal utilization

Energy Technology Data Exchange (ETDEWEB)

Rose, A.; Lim, D.; Frias, O.; Benavides, J. [Pennsylvania State Univ., University Park, PA (United States). Dept. of Mineral Economics; Tompkins, M.M. [Argonne National Lab., IL (United States)

1994-12-01

The People`s Republic of China (hereafter referred to as China) is the largest producer and consumer of coal in the world. The dominance of coal in China`s energy balance has come at a high price to the environment. With the recent attention given to global warming issues, China`s energy consumption and production practices have become the subject of much concern. Of particular concern is China`s ability to reduce CO{sub 2} emissions by constraining coal use and the impact such policies will likely have on the Chinese economy. The study is divided into two reports. Volume 1 focuses on the full coal fuel cycle, emissions, and environmental effects. This report (Volume 2) analyzes various CO{sub 2} mitigation strategies and determines their effect on economic growth. Contrary to what some analysts have claimed, the current work suggests that it would not be costly for the Chinese to reduce CO{sub 2} emissions. In fact, some strategies were accompanied by increases in China`s energy and economic efficiency, which actually stimulated economic growth.

Indian coal industry: Growth perspective

International Nuclear Information System (INIS)

Sachdev, R.K.

1993-01-01

Growth perspective of Indian coal industry and their environmental aspects, are discussed. The complete coal chain comprises of mining including preparation and processing, transport, usage and disposal of solid, liquid and gaseous wastes. Proper environmental protection measures are therefore, required to be integrated at every stage. At mining stage, land reclamation, restoration of surface damaged by subsidence and proper treatment of effluents are the minimum requirement for effective environmental protection. Since coal will continue to be the major source of commercial energy in coming decades initiative will have to be taken in making coal a clean fuel from the point of view of its usage in different industries. Washing of high ash coals for reducing the ash content will go a long way in reducing the atmospheric pollution through better plant performance and reduced environmental pollution at the power plants. (author)

Healy Clean Coal Project: Healy coal firing at TRW Cleveland Test Facility. Final report

Energy Technology Data Exchange (ETDEWEB)

Koyama, T.; Petrill, E.; Sheppard, D.

1991-08-01

A test burn of two Alaskan coals was conducted at TRW`s Cleveland test facility in support of the Healy Clean Coal Project, as part of Clean Coal Technology III Program in which a new power plant will be constructed using a TRW Coal Combustion System. This system features ash slagging technology combined with NO{sub x} and SO{sub x} control. The tests, funded by the Alaska Industrial Development and Export Authority (AIDEA) and TRW, were conducted to verify that the candidate Healy station coals could be successfully fired in the TRW coal combustor, to provide data required for scale-up to the utility project size requirements, and to produce sufficient flash-calcined material (FCM) for spray dryer tests to be conducted by Joy/NIRO. The tests demonstrated that both coals are viable candidates for the project, provided the data required for scale-up, and produced the FCM material. This report describes the modifications to the test facility which were required for the test burn, the tests run, and the results of the tests.

National Coal Utilization Assessment. An integrated assessment of increased coal use in the Midwest: impacts and constraints. [14 states Midwest region

Energy Technology Data Exchange (ETDEWEB)

1977-10-01

This study examines the impacts and constraints to increased coal production and use for a 14-state Midwestern region. The assessment considers technology characteristics, energy supply and demand trends, siting constraints, impacts on water availability and coal reserves, impacts on air and water quality, and ecosystems, effects of trace elements, social and economic impacts, and health risks. The significant air quality constraints to coal use are related to the short-term National Ambient Air Quality Standards, PSD standards, and exposure to sulfates. In general, cumulative water supply in the 14-state region is adequate to satisfy foreseeable energy requirements; however, on a localized basis significant water shortages may develop which could constrain a smaller portion of the energy development. Water quality impacts are primarily restricted to areas with insufficient water resources. Coal mining will continue to have significant effects on water quality in smaller streams draining the major coal regions unless strict control practices are maintained. Coal-conversion plants may cause localized water quality problems; however, the effluent characteristics of these plants are not well-known. A significant amount of the coal development is anticipated to occur in counties with high susceptibility to social and economic impacts. The timing, magnitude, and nature of these impacts could be mitigated by the development of effective management strategies.

Bench-scale testing of a micronized magnetite, fine-coal cleaning process

Energy Technology Data Exchange (ETDEWEB)

Suardini, P.J. [Custom Coals, International, Pittsburgh, PA (United States)

1995-11-01

Custom Coals, International has installed and is presently testing a 500 lb/hr. micronized-magnetite, fine-coal cleaning circuit at PETC`s Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program`s, High Efficiency Preparation Subprogram. The project includes design, construction, testing, and decommissioning of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense medium cycloning of the 300 by 30 micron feed coal using a nominal minus 10 micron size magnetite medium, and medium recovery using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Seventh symposium on coal mine drainage research. NCA/BCR coal conference and Expo IV

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-01

The Seventh Symposium on Coal Mine Drainage Research, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Seventeen papers from the proceedings have been entered individually into EDB and ERA. Topics covered include chemical reactions of pyrite oxidation and acid formation in spoil banks, abandoned mines, etc., formation of small acid lakes from the drainage and their neutralization by natural and other neutralization measures, trace elements in acid mine drainage, ground water contamination, limnology, effects of surface mined ground reclamation and neutralization, water purification and treatment, mining and coal preparation plant waste disposal, ash and fly ash disposal (to minimize leaching from the wastes), runoff from large coal storage stockpiles during storms (prevention of environmental effects by collection and neutralization by passing through an ash pond). (LTN)

Report on the fiscal 1997 result of the Japan-China joint demonstration project of environment-friendly cost utilization systems. Low grade coal combustion system (Zhejiang Huba Co. Ltd.); 1997 nendo seika hokokusho kankyo chowagata sekitan riyo system kyodo jissho jigyo. Teihin`itan nensho system ni kakawaru jissho jigyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

This demonstration project aims at reduction of pollutants derived from coal utilization in China by demonstration of CCT to be diffused in China and preparation of diffusion bases, and stable import of energy for Japan. A low-grade coal combustion system burns low-grade coal by use of an internal circulating fluidized bed boiler which burns coal by uniform mixing and circulation of coal and some particles such as limestone and ash. Main specifications of the boiler are as follows: evaporation rate of 35t/h, steam pressure of 3.82MPa (39.0kg/cm{sup 2}), steam temperature of 450degC, water supply temperature of 150degC, internal circulating fluidized bed combustion type, boiler efficiency of 75%, and desulfurization rate of 90% or more. Main properties of low-grade coal are as follows: calorific value of 1830kcal/kg, coal size of 10mm or less, total water content of 2.5%, total S content of 2.7%, ash content of 67.7%, limestone purity of 50% or more, and stone size of 3mm or less. The results in fiscal 1997 are as follows: field survey and arrangement, basic planning and design, design, production and procurement of equipment, training, and dispatch of field supervisor. 26 figs., 3 tabs.

Bugs and coal: processing fuels with biotechnology

Energy Technology Data Exchange (ETDEWEB)

Shepard, M

1987-06-01

Bioprocessing of coal is developing along several fronts, each of potential significance to utilities. Researchers have found a fungus, polyporous versicolor, which can liquefy certain kinds of coal and scientists have genetically engineered bacteria that remove sulfur and ash-forming metal impurities from coal. Research programs are being undertaken to find organisms that will convert lignite into gaseous methane to produce gaseous fuel more economically than the current coal gasification methods. Researchers looking for ways to remove sulfur from coal before it is burned are evaluating the use of a bacterium called thiobacillus ferroxidans to enhance the physical removal of pyrite. 2 refs.

Utilizing the PREPaRE Model When Multiple Classrooms Witness a Traumatic Event

Science.gov (United States)

Bernard, Lisa J.; Rittle, Carrie; Roberts, Kathy

2011-01-01

This article presents an account of how the Charleston County School District responded to an event by utilizing the PREPaRE model (Brock, et al., 2009). The acronym, PREPaRE, refers to a range of crisis response activities: P (prevent and prepare for psychological trauma), R (reaffirm physical health and perceptions of security and safety), E…

Activities of the Institute of Chemical Processing of Coal at Zabrze

Energy Technology Data Exchange (ETDEWEB)

Dreszer, K.

1995-12-31

The Institute of Chemical Processing of Coal at Zabrze was established in 1955. The works on carbochemical technologies have been, therefore, carried out at the Institute for 40 years. The targets of the Institute`s activities are research, scientific and developing works regarding a sensible utilization of fuels via their processing into more refined forms, safe environment, highly efficient use of energy carriers and technological products of special quality. The Institute of Chemical Processing of Coal has been dealing with the following: optimized use of home hard coals; improvement of classic coal coking technologies, processing and utilization of volatile coking products; production technologies of low emission rate fuels for communal management; analyses of coal processing technologies; new technologies aimed at increasing the efficiency of coal utilization for energy-generating purposes, especially in industry and studies on the ecological aspects of these processes; production technologies of sorbents and carbon activating agents and technologies of the utilization; rationalization of water and wastes management in the metallurgical and chemical industries in connection with removal of pollution especially dangerous to the environment from wastes; utilization technologies of refined materials (electrode cokes, binders, impregnating agents) for making electrodes, refractories and new generation construction carbon materials; production technologies of high quality bituminous and bituminous and resin coating, anti-corrosive and insulation materials; environmentally friendly utilization technologies for power station, mine and other wastes, and dedusting processes in industrial gas streams.

Coal flotation technical review

Energy Technology Data Exchange (ETDEWEB)

Heiser, N. [C. Clarkson & Associates Pty. Ltd., Brisbane, Qld. (Australia)

1996-10-01

The Australian Coal Association Research Program (ACARP) recently commissioned a study into the status of flotation in coal preparation, in order to direct limited funds to areas of maximum benefit. The primary purpose of the study was the assessment of new flotation technologies, including those commercially available and those still under development. Technologies examined included: the Jameson Cell, Microcel, and Ekof cell. Problems and advantages are discussed, with suggestions for future areas of research. 3 figs.

Preparation and extraction of sloping seams without leaving inter-drift coal pillars

Energy Technology Data Exchange (ETDEWEB)

Artamonov, N S; Bormotov, I N; Brovko, I I

1977-10-01

A description is given of mining three coal seams in the Kuznetsk Basin without leaving coal pillars because they could not withstand the stress of the induced reference pressure. This system reduced coal losses in 1976 in comparison to 1970 and eliminated local accumulations of methane by withdrawing it through the excavated area. The system was noted to have the disadvantage of additional expenditures for timber supports. 2 figures.

30 CFR 819.13 - Auger mining: Coal recovery.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Auger mining: Coal recovery. 819.13 Section 819....13 Auger mining: Coal recovery. (a) Auger mining shall be conducted so as to maximize the utilization and conservation of the coal in accordance with § 816.59 of this chapter. (b) Auger mining shall be...

Continuous quality control of mined hard and soft coals

International Nuclear Information System (INIS)

Fertl, W.H.; Gant, P.L.

1978-01-01

A method is provided for determining the shale content of mined coal by monitoring the thorium content of the coal. Thorium content and ash content are shown to be related whereby a direct reading of the thorium will be indicative of the shale content of the coal and the ash content of the coal. The method utilizes the natural radiation of thorium to provide the continuous or selective control of mined coals