WorldWideScience

Sample records for coal measure strata

  1. Behaviors of overlying strata in extra-thick coal seams using top-coal caving method

    Bin Yu

    2016-04-01

    Full Text Available Accidents such as support failure and excessive deformation of roadways due to drastic changes in strata behaviors are frequently reported when mining the extra-thick coal seams Nos. 3–5 in Datong coal mine with top-coal caving method, which significantly hampers the mine's normal production. To understand the mechanism of strata failure, this paper presented a structure evolution model with respect to strata behaviors. Then the behaviors of strata overlying the extra-thick coal seams were studied with the combined method of theoretical analysis, physical simulation, and field measurement. The results show that the key strata, which are usually thick-hard strata, play an important role in overlying movement and may influence the mining-induced strata behaviors in the working face using top-coal caving method. The structural model of far-field key strata presents a “masonry beam” type structure when “horizontal O-X” breakage type happens. The rotational motion of the block imposed radial compressive stress on the surrounding rock mass of the roadway. This can induce excessive deformation of roadway near the goaf. Besides, this paper proposed a pre-control technology for the hard roof based on fracture holes and underground roof pre-splitting. It could effectively reduce stress concentration and release the accumulated energy of the strata, when mining underground coal resources with top-coal caving method.

  2. Effects of increased rock strata stresses on coal gettability

    Sikora, W; Skoczynski, W [Politechnika Slaska, Gliwice (Poland). Instytut Mechanizacji Gornictwa

    1988-01-01

    Analyzes effects of rock strata pressure on a coal seam, its cracking and on energy consumption of coal cutting by shearer loaders and coal plows. Effects of mining depth on stresses in a coal seam rib side were analyzed using formulae developed by Budryk, Chudek and Borecki. Formulae used for selecting optimum yield strength of powered supports at working faces are reviewed. Four types of spontaneous separation of coal seam blocks caused by rock strata stresses are evaluated: layers parallel to the face with constant thickness, coal blocks with thickness decreasing in the direction of the floor or roof (blocks with a planar triangle cross-cut), blocks situated in the seam layer adjacent to the floor or roof. Causes of each type of coal seam separation are analyzed. 9 refs.

  3. Law of Strata Pressure Behavior in Shallow Coal Seam

    Zhao, Jian; Liu, Leibin; Zheng, Zhiyang

    2018-02-01

    The law of strata pressure behavior in shallow coal seam is analyzed, according to the load data of Jinjie Coal Mine 31109 working face hydraulic supports. The first weighting distance of main roof is 80 m, and the periodic weighting distance of main roof is about 20 m. And according to the load data in the middle and both ends of the working face, the working resistance of hydraulic supports and the setting load are a bit small, so they couldn’t meet the needs of supporting roof. Then, the front abutment pressure of working face is analyzed by numerical simulation. It does not only explain the reason that the load is too big, but also explains the reason that the strata pressure behavior in shallow coal seam is serious. The length of undamaged main roof rock beam verifies the correctness of the periodic weighting distance.

  4. Seismic modelling of coal bed methane strata, Willow Creek, Alberta

    Richardson, S.E.; Mayer, R.; Lawton, D.C.; Langenberg, W. [Consortium for Research in Elastic Wave Exploration Seismology, Calgary, AB (Canada)

    2001-07-01

    The purpose is to determine the feasibility of applying high- resolution reflection seismic surveying to coalbed methane (CBM) exploration and development. Numerical reflection seismic methods are examined for measuring the mapping continuity and coherence of coal zones. Numerical modelling of a coal zone in Upper Cretaceous sediments near Willow Creek, Alberta indicates that seismic data that is predominantly of 100 Hz is required to map the coal zone and lateral facies variations within the deposit. For resolution of individual coal seams, a central frequency >150 Hz would be needed. 26 refs., 17 figs., 3 tabs.

  5. Analysis of support installation and strata control in ventilation tunnels and coal chutes in steep seams

    Moroz, V D; Belyaev, A N; Kostyuk, I S

    1984-01-01

    The VNIMI and the Donugi branch in Gorlovka developed and tested a system for strata control in gate roads for ventilation and in coal chutes in inclined and steep medium and thick coal seams. The roof is supported by cribbings made of slabs of reinforced concrete with yielding elements. Timber is used as yielding material. Tests showed that thickness of yielding layers between concrete slabs should range from 15 to 20% of coal seam thickness. Yielding elements increase yield strength of the system to about 2 MN (load distribution is more regular). The tests show that the cribbings are an efficient system for strata control in workings driven in coal seams with dip angle from 35 to 60 degrees. Performance of concrete cribbings in ventilation gate roads and coal chutes in selected mines of the Ukrainian SSR is analyzed.

  6. Origin of discontinuities in coal-bearing strata at Roaring Creek (Basal Pennsylvanian of Indiana)

    Nelson, W J; Eggert, D L; Dimichele, W A; Stecyk, A C

    1985-05-01

    Basal Pennsylvanian coal-bearing strata exposed along Roaring Creek, west-central Indiana, exhibit extreme lateral discontinuity. Coal seams abruptly change in thickness and elevation; they split, grade into shale, are cut out by channels and disrupted by soft-sediment deformational structures. Initial sediments were laid down by a network of southwest- flowing streams that traversed a deeply channelized upland surface of Mississippian carbonate rocks. Channels aggraded rapidly as uplands were worn down, so the region changed through time from uplands to upper deltaic plain. Local environments included channels, localized point bars, small natural levees and crevasse splays, overbank deposits, and swamps. Differential compaction and subsidence, slumping stream banks, and possibly collapsing sinkholes influenced sedimentation. As a consequence, coals are too discontinuous for economical mining, although they are locally thick and high in quality. 16 references.

  7. Study on Strata Behavior Regularity of 1301 Face in Thick Bedrock of Wei - qiang Coal Mine

    Gu, Shuancheng; Yao, Boyu

    2017-09-01

    In order to ensure the safe and efficient production of the thick bedrock face, the rule of the strata behavior of the thick bedrock face is discussed through the observation of the strata pressure of the 1301 first mining face in Wei qiang coal mine. The initial face is to press the average distance of 50.75m, the periodic weighting is to press the average distance of 12.1m; during the normal mining period, although the upper roof can not be broken at the same time, but the pressure step is basically the same; the working face for the first weighting and periodical weighting is more obvious to the change of pressure step change, when the pressure of the working face is coming, the stent force increased significantly, but there are still part of the stent work resistance exceeds the rated working resistance, low stability, still need to strengthen management.

  8. Technique for reinforcing development working in lower strata of thick coal seams

    Andranovich, V A; Gromov, Yu V; Kurglikov, V P

    1981-01-15

    This device is to be used by mining industry, specifically for reinforcing development work in bottom strata of thick coal seams having a layer depression. Reinforcing consists of drilling a hole, or making cutting slits and lowering support props for the stratum below through them, as well as lowering the roof timber on the ground. To cut back expenditures on installation and removal of equipment, drilling or making cutting slits is done to a depth equal to the total height of the substrata, and the support props are laid for all of the substrata. Only the roof timber is lowered on the ground during work on the layers.

  9. Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

    Jinyi TAO; Yuchen ZHANG

    2014-01-01

    The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These p...

  10. On-Site Radon Detection of Mining-induced Fractures from Overlying Strata to the Surface: A Case Study of the Baoshan Coal Mine in China

    Wei Zhang

    2014-12-01

    Full Text Available Large-scale longwall mining of shallow coal seams may cause mining-induced fractures that can project completely through to the surface. This could lead to a series of mine safety and environmental issues, further deteriorating the already fragile ecological environment in the Western mining areas in China. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures from overlying strata to the surface in the Baoshan Coal Mine (BCM. The on-site test indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.

  11. Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

    Jinyi TAO

    2014-09-01

    Full Text Available The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These parameters are magnetic permeability m (H/m, dielectric constant e (F/m and electrical conductivity s (S/m. In these parameters, electrical conductivity is not constant. Under the influence of various factors, it will be great changes. This paper, for the specific circumstances of coal mine rock, discuses and conduct dada mining the effect frequency on the electrical conductivity of underground rock in coal mine with through-the-earth wireless communication.

  12. Determining the degree of break up of coal strata and clay interlayers by looseners at the Chukurovo pit

    Atanasov, A B; Stoyanov, D S; Yordanov, Y M

    1983-01-01

    One of the rational technologies for selective mining of thin coal strata with complex geological structure is that one in which different types of mechanical looseners are used. Identification of the degree of break up of the rock is accomplished most rapidly and precisely using seismoacoustical methods. The evaluation is conducted relative to the speed of propagation of elastic waves in the mass. SVM seismic receivers were used at the Chukurovo pit to determine the speed of propagation of an elastic wave in coals and clays. Shafts 10 meters long were drilled in three experimental fields using the SVB-2 machine. The speed of propagation of an elastic wave in the coals and in sandy clays was determined for different shaft depths every meter. After comparing the obtained results with standard tables from different companies, the possibility of breaking up the coal and clay interlayers in the experimental sectors by looseners with motors different in type and capacity was determined.

  13. Reservoir characteristics of coal-shale sedimentary sequence in coal-bearing strata and their implications for the accumulation of unconventional gas

    Wang, Yang; Zhu, Yanming; Liu, Yu; Chen, Shangbin

    2018-04-01

    Shale gas and coalbed methane (CBM) are both considered unconventional natural gas and are becoming increasingly important energy resources. In coal-bearing strata, coal and shale are vertically adjacent as coal and shale are continuously deposited. Research on the reservoir characteristics of coal-shale sedimentary sequences is important for CBM and coal-bearing shale gas exploration. In this study, a total of 71 samples were collected, including coal samples (total organic carbon (TOC) content >40%), carbonaceous shale samples (TOC content: 6%-10%), and shale samples (TOC content TOC content. Clay and quartz also have a great effect on the porosity of shale samples. According to the FE-SEM image technique, nanoscale pores in the organic matter of coal samples are much more developed compared with shale samples. For shales with low TOC, inorganic minerals provide more pores than organic matter. In addition, TOC content has a positive relationship with methane adsorption capacity, and the adsorption capacity of coal samples is more sensitive than the shale samples to temperature.

  14. Palynology of the coal-bearing strata of Santofirme (Oviedo, Northern Spain)

    Horvath, V.

    1984-01-01

    In the immediate vicinity of Santofirme, 16 km south-east of Oviedo, there is an 18 km/sup 2/ outcrop of material from the Carboniferous period which forms a syncline running north-east to south-west and which, in places, is covered with Permo-Triassic and Tertiary material from the Depresion de Llanera. The series consists of regularly alternating layers of lutite and sandstone with bands of coal and a few lime bands in the lower section. Twenty-one of the coal bands, grouped together in eight packets, are worked by Minas de Villabona SA. All the coal bands in the western flank of the syncline have been tested. Most of the samples were collected from four drillings carried out by ENADIMSA in 1982; those remaining were taken from the surface at the Arroyo Socavon and La Tejera opencast sites.

  15. Modeling of Three Flat Coal Seams Strata Developing at Open Pit Miming

    Gvozdkova, Tatiana; Markov, Sergey; Demirel, Nuray; Anyona, Serony

    2017-11-01

    The use of low-cost direct dumpling technology, as is well known, has a relatively limited field of application: flat coal seams, and the higher the dip angle of the seam, the more difficult it is to place the necessary volume of overburden rock in the dumping layers. For this, we have to pour four-tier dumps. In this article, four possible options for piling the dump have been studied and prerequisites have been made for further research aimed at improving the efficiency of the use of direct dumpling technology in the development of flat coal seams.

  16. Measuring ash content of coal

    Clayton, C.G.; Wormald, M.R.

    1980-01-01

    An apparatus for measuring the ash content of coal is claimed. It comprises a means for irradiating a known quantity of coal in a transport container with a known dose of neutrons, a means for detecting γ-rays having a predetermined energy emitted by the irradiated coal, the γ-rays being indicative of the presence of an ash-forming element in the coal, a means for producing a signal related to the intensity of the γ-ray emission and a means responsive to the signal to provide an indication of the concentration of the ash-forming element in the coal

  17. Origin of natural waters and gases within the Upper Carboniferous coal-bearing and autochthonous Miocene strata in South-Western part of the Upper Silesian Coal Basin, Poland

    Kotarba, Maciej J.; Pluta, Irena

    2009-01-01

    The molecular and stable isotope compositions of coalbed gases from the Upper Carboniferous strata and natural gases accumulated within the autochthonous Upper Miocene Skawina Formation of the Debowiec-Simoradz gas deposit were determined, as well as the chemical and stable isotope compositions of waters from the Skawina Formation and waters at the top of the Upper Carboniferous strata of the Kaczyce Ridge (the abandoned 'Morcinek' coal mine) in the South-Western part of the Upper Silesian Coal Basin. Two genetic types of natural gases within the Upper Carboniferous coal-bearing strata were identified: thermogenic (CH 4 , small amounts of higher gaseous hydrocarbons, and CO 2 ) and microbial (CH 4 , very small amounts of ethane, and CO 2 ). Thermogenic gases were generated during the bituminous stage of coalification and completed at the end of the Variscan orogeny. Degassing (desorption) of thermogenic gases began at the end of late Carboniferous until the late Miocene time-period and extended to the present-day. This process took place in the Upper Carboniferous strata up to a depth of about 550 m under the sealing Upper Miocene cover. A primary accumulation zone of indigenous, thermogenic gases is present below the degassing zone. Up to 200 m depth from the top of the Upper Carboniferous strata, within the weathered complex, an accumulation zone of secondary, microbial gas occurs. Waters within these strata are mainly of meteoric origin of the infiltration period just before the last sea transgression in the late Miocene and partly of marine origin having migrated from the Upper Miocene strata. Then, both methanogenic archaebacteria and their nutrients were transported by meteoric water into the near-surface Carboniferous strata where the generated microbial CH 4 saturated coal seams. Waters within the Miocene strata of the Debowiec-Simoradz and Zablocie are of marine origin, and natural gases accumulated within autochthonous Miocene strata of the Debowiec

  18. Measurement of sub-surface strata behaviour in bord and pillar mining: a case study

    Krishna, R.

    1991-01-01

    Ranigunj coalfield (India) has been facing significant problems due to subsidence as a result of underground mining of coal seams. The occurrence of the thick seams in close proximity, shallow depth, great variation in the nature of superincumbent strata from site to site, followed by the slow rate of extraction, has aggravated subsidence problems. In the recent past, many such workings have collapsed, damaging a large number of surface structures. In view of the aforesaid need, a comprehensive project financed by the Ministry of Energy (Coal), was undertaken by the Department of Mining Engineering, Indian Institute of Technology, Kharagpur, at a Colliery in Ranigunj Coalfield. This investigation revealed that the caving horizon occurred at 4 times the extracted seam height, which differs from the findings in the UK, USA, and Australia. Also, it appears possible to estimate strata displacements from geological and physicomechanical information from the overlying rocks using the bending moment principle. Further, it was observed that the shallow workings could give rise to a sink hole type of subsidence, which is dangerous and could adversely affect the environment, safety of the public and properties. 11 refs., 13 figs., 1 tab

  19. Leaching Process of Rare Earth Elements, Gallium and Niobium in a Coal-Bearing Strata-Hosted Rare Metal Deposit—A Case Study from the Late Permian Tuff in the Zhongliangshan Mine, Chongqing

    Jianhua Zou; Heming Tian; Zhen Wang

    2017-01-01

    The tuff, a part of coal-bearing strata, in the Zhongliangshan coal mine, Chongqing, southwestern China, hosts a rare metal deposit enriched in rare earth elements (REE), Ga and Nb. However, the extraction techniques directly related to the recovery of rare metals in coal-bearing strata have been little-studied in the literature. The purpose of this paper is to investigate the extractability of REE, Ga and Nb in the tuff in the Zhongliangshan mine using the alkaline sintering-water immersion-...

  20. Strata control in deep coal mines. Control de estratos en tajos subteraneos de la mineria del carbon

    Ramirez Oyanguren, P.; De la Cuadra, L.

    1985-01-01

    The six chapters cover the following subjects: mining methods used in Spanish coal mines; rock movement and pressure around a longwall face; roof bed study; underground support systems; gas dynamic phenomena; and instrumentation for underground mine monitoring.

  1. Problems of the processing of nuclear magnetic logging signals (identification of fluid-containing strata from a number of measurements)

    Aliev, T.M.; Orlov, G.L.; Lof, V.M.; Mityushin, E.M.; Ragimova, E.K.

    1978-01-01

    Problems of the processing of nuclear magnetic logging signals to identification of fluid-containing strata from a number of measurements. Problems of application statistical decision theory to discovery of fluid-containing beds from a number of measurements are considered. Using the technique possibilities of nuclear magnetic logging method the necessary volume of samples is motivated, the rational algorithm for processing of sequential measurements is obtained

  2. Automated mineralogical logging of coal and coal measure core

    Stephen Fraser; Joan Esterle; Colin Ward; Ruth Henwood; Peter Mason; Jon Huntington; Phil Connor; Reneta Sliwa; Dave Coward; Lew Whitbourn [CSIRO Exploration & Mining (Australia)

    2006-06-15

    A mineralogical core logging system based on spectral reflectance (HyLogger{trademark}) has been used to detect and quantify mineralogies in coal and coal measure sediments. The HyLogger{trademark} system, as tested, operates in the visible-to-shortwave infrared spectral region, where iron oxides, sulphates, hydroxyl-bearing and carbonate minerals have characteristic spectral responses. Specialized software assists with mineral identification and data display. Three Phases of activity were undertaken. In Phase I, carbonates (siderite, ankerite, calcite) and clays (halloysite, dickite) were successfully detected and mapped in coal. Repeat measurements taken from one of the cores after three months demonstrated the reproducibility of the spectral approach, with some spectral differences being attributed to variations in moisture content and oxidation. Also, investigated was HyLogger{trademark} ability to create a 'brightness-profile' on coal materials, and these results were encouraging. In Phase II, geotechnically significant smectitic clays (montmorillonite) were detected and mapped in cores of clastic roof and floor materials. Such knowledge would be useful for mine planning and design purposes. In Phase III, our attempts at determining whether phosphorus-bearing minerals such as apatite could be spectrally detected were less than conclusive. A spectral index could only be created for apatite, and the relationships between the spectrally-derived apatite-index, the XRD results and the analytically-derived phosphorus measurements were ambiguous.

  3. Coal Mine Accidents in Bangladesh: Its Causes and Remedial Measures

    MD. MINHAJ UDDIN MONIR

    2012-12-01

    C, water flow 600 m3/hr and humidity 100%. Due to roof-fall, toxic gas and very high temperature and humidity in the face 1105 and 1108, some miners were highly injured and died. Therefore, taking necessary safety and risk measures during development of face and roadway in BCM, production will be sustained by controlling roof-fall. Strata pressure of every faces is monitor regularly through electromagnetic emission detector as well as changing sufficient ventilation system, accidents of BCM could be controlled. Adding earth filling materials (e.g. sand, silt etc. in to the vacuum goaf area, air blast accident should be reduced and surface subsidence would also be controlled. Considering all the problems of 1st slice and initiating extra caution for face development accident in BCM may reduce in 2nd slice and overall production may be increased significantly.

  4. Micrinite maceral evidence of hydrocarbon generation in cretaceous coal measures of the middle Benue trough, Nigeria

    Obaje, N. G.; Ukpabio, E. J.; Funtua, I. I.

    1999-01-01

    Maceral analysis on samples from the coal and coal-bearing strata of the Awgu Formation in the Middle Benue Trough of Nigeria allows the subdivision of the coal beds and inter seam sediments into three different petrographic/coal facies, namely: a vitrinite-fusinite coal facies which is rich in vitrinite, poor in liptinite, with variable amounts of inertinite and low mineral matter content; a trimaceritic coal facies which is rich in vitrinite, liptinite and inertinite with low mineral matter content; and a shaley coal facies which, expectedly, is dominated by mineral matter and has variable amounts of vitrinite, liptinite and inertinite. Micrinite macerals constitute 8.2% and 4.5 on mineral matter-counted basis in samples from the trimaceritic and shaley coal facies respectively. These amounts, in both cases, are considered to be very high. They occur as finely particulate, rounded grains approximately I um in diameter. Most of the micrinite are closely associated with highly reflecting, almost unrecognizable liptinite. The nature and origin of micrinite and its significance to oil and gas generation have been studied extensively. As secondary macerals, they are generally believed to be relics of oil generation from oil-prone macerals, mainly liptinitic and vitrinitic macerals with which they are closely associated. Reflectance measurements on the associated vitrinite macerals indicate a thermal maturity range of 0.74 - 1.25 % Rm. This range corresponds to the zone of oil generation in most minerogenic oil source rocks. In the study area, however, only the trimaceritic coal facies and some parts of the shaley coal facies that are rich in liptinite alongside the associated micrinite macerals are considered to have generated oil. The vitrinite-fusinite coal facies with its high content of humic organic matter (vitrinite + Inertinite) can only generate gas (wet + dry) within the given thermal maturity range

  5. Leaching Process of Rare Earth Elements, Gallium and Niobium in a Coal-Bearing Strata-Hosted Rare Metal Deposit—A Case Study from the Late Permian Tuff in the Zhongliangshan Mine, Chongqing

    Jianhua Zou

    2017-05-01

    Full Text Available The tuff, a part of coal-bearing strata, in the Zhongliangshan coal mine, Chongqing, southwestern China, hosts a rare metal deposit enriched in rare earth elements (REE, Ga and Nb. However, the extraction techniques directly related to the recovery of rare metals in coal-bearing strata have been little-studied in the literature. The purpose of this paper is to investigate the extractability of REE, Ga and Nb in the tuff in the Zhongliangshan mine using the alkaline sintering-water immersion-acid leaching (ASWIAL method. The results show that ASWIAL can separate and extract REE, Ga and Nb effectively under the optimized conditions of calcining at 860 °C for 0.5 h with a sample to sintering agent ratio of 1:1.5, immersing at 90 °C for 2 h with 150 mL hot water dosage, and leaching using 4 mol/L HCl at 40 °C for 2 h with a liquid-solid ratio of 20:1 (mL:g. The final leaching efficiencies of REE and Ga are up to 85.81% and 93.37%, respectively, whereas the leaching efficiency of Nb is less than 1%, suggesting the high concentration of Nb in the leaching residue, which needs further extraction.

  6. Analysis of the saturated hydrocarbon in coal, carbonaceous mudstone and oils from the lower Jurassic coal measures in the Turpan Basin by GC/MS

    Fang Xuan; Meng Qianxiang; Sun Minzhuo; Du Li; Ding Wanren

    2005-01-01

    Saturated hydrocarbon of coal, carbonaceous mudstone and oils from the Lower Jurassic coal measures in the Turpan basin were studied, and biomarker characteristics and coal thermal maturity analyzed to draw the following conclusions. T here are many similar biomarker characteristics between oil from middle-lower Jurassic of Turpan Basin and coal and carbonaceous mudstone in the same strata. They all contain specific r-lupane, I-norbietane, C 24 -tetracyclic and high content of C 29 -steranes. These characteristics suggest that they have similar matter source of the organic matter derived from matter with abundant high plants. Meanwhile, biomarkers often used to indicate depositional environments characterized by high Pr/Ph ratio, little or no gammacerane and high abundance dibenzofurans, such biomarker distributions are indicative of suboxic and freshwater environment. Although coal and carbonaceous mudstone remain in lower thermal maturity (Ro=0.47-0.53), but C 29 -ββ/(αα+ββ) sterane ratio (0.294-0.489) and bezohopane are detected. Because these ferture are related to bacterial activity, bacterial degradation of organic matter maybe take an important role in coal-derived oil. (authors)

  7. Rupture and seepage law of roof-floor strata caused by coal mining between double-bearing aquifers%双承压水间采煤顶底板破断及渗流规律

    王金安; 魏现昊; 纪洪广

    2012-01-01

    Based on coal mining between double-bearing aquifers in Shanxi Province, and focused on the stress-fluid coupling mechanism of coal and rocks, the study employed physical simulation experiment and discrete element numer- ical simulation to reveal the rupture regularity of stratum and the seepage with respect to different mining advances. The developing modes of water conductive zones in ruptured roof strata were put forward and the correspondent rela- tionship between the formation of ' four zones' in the floor strata and the mining process were established. The study shows that the mining area floor only appears broken zone during primary mining. When a full mining arrives, new damaged zone and mining induced water conductive-rising zone begin to develop. The new der the working face. At back of the mining face, the new damaged zone is mainly un- damaged zone is progressively closed because of the compac- tion of gob. The stress-seepage coupling effect in mining disturbed rock mass can be summarized as follows:the mining leads to rupture of roof and floor strata and a stress drop. The water permeability in rock mass increases, resulting in the aquifer in Taihui strata rush-in the goaf and mining face. The water conductive fracture zone develops and water conducting arises in the water proof layer in the floor strata under the water wedge splitting action. When the residual water pressure can not continuously split the water proof layer in the floor strata against the tensile strength of the rock mass, a stress-seepage stable state is recovered in the floor strata.%以山西某煤矿双承压水间下组煤开采为背景,针对煤岩应力一渗流耦合机理,采用相似材料模拟和离散元数值模拟,揭示双承压水间下组煤不同开采尺度下岩体断裂模式和渗流规律,提出顶板导水裂隙带发展模式,并建立底板“四带”形成与工作面开采过程的对应关系。研究发现:初采期间底板仅发育

  8. Observer-based Coal Mill Control using Oxygen Measurements

    Andersen, Palle; Bendtsen, Jan Dimon; S., Tom

    2006-01-01

    This paper proposes a novel approach to coal flow estimation in pulverized coal mills, which utilizes measurements of oxygen content in the flue gas. Pulverized coal mills are typically not equipped with sensors that detect the amount of coal injected into the furnace. This makes control...... of the coal flow difficult, causing stability problems and limits the plant's load following capabilities. To alleviate this problem without having to rely on expensive flow measurement equipment, a novel observer-based approach is investigated. A Kalman filter based on measurements of combustion air flow led...... into the furnace and oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate, it becomes possible to close an inner loop around the coal mill itself, thus giving a better disturbance rejection capability. The approach is validated against...

  9. The mechanism and characteristics of ground movement and strata failure caused by mining

    Tianquan, L. (Central Coal Mining Research Institute, Beijing (China))

    1988-01-01

    Analyzes strata movement and ground subsidence caused by underground coal mining. Five types of strata failure during and after underground coal mining are comparatively evaluated: caving zone, fractured zone, bending zone, arched caving, bending with continuous ground movement, sinkhole formation. Effects of coal seam thickness, dip angle, coal panel dimensions, rock stratification and mechanical properties on dimensions and distribution of failure zones in rock strata are investigated. Strata movement during level and steep seam mining is comparatively evaluated. Causes of continuous ground surface deformation and discontinuous deformation are analyzed. Rock strata properties and water influx, which influence sinkhole hazards, are discussed.

  10. Revised models for hydrocarbon generation, migration and accumulation in Jurassic coal measures of the Turpan basin, NW China

    Li Maowen; Stasiuk, L.D. [Geological Survey of Canada, Calgary, Alberta (Canada); Bao Jianping [Jianghan Petroleum University, Hubei (China); Lin, R. [Petroleum University (Beijing), Changping (China); Yuan Mingsheng [PetroChina Tu-Ha Oilfield Company, Xingjiang (China)

    2001-07-01

    Whether or not the Lower-Middle Jurassic coal measures in the Turpan basin of NW China have generated commercial quantities of liquid petroleums is a problem of considerable importance that remains contentious as it has not yet been resolved unequivocally. This study provides evidence against the Jurassic humic coals as the only major source for the oils discovered in the Taibei depression of this basin and suggests additional significant contributions from the Upper Permian and Middle-Lower Jurassic lacustrine source rocks. The Carboniferous-Permian marine source rocks may have been important also in limited locations along the major basement faults. Molecular and petrographic data indicate that the majority of the Middle Jurassic strata are currently immature or marginally mature with respect to hydrocarbon generation. Within the major depocenters, the Middle-Lower Jurassic coal-bearing strata of the Baodaowan and Xishanyao formations has reached the conventional oil window (i.e. with vitrinite reflectance >0.7 per cent Ro). Pre-Jurassic (Upper Permian in particular) derived hydrocarbons appear to be widespread in extracts of fractured Jurassic coal and fine-grained rocks. Large differences have been observed in the absolute concentrations of biomarker compounds in rock extracts of various source intervals. Thus, 'coaly' biomarker signatures of the oils most likely resulted from mixing and migration contamination when hydrocarbons derived from mature source rocks migrated up through highly fractured coal seams along deep-seated faults. In addition to conventional exploration targets, revised petroleum generation and accumulation models predict that the focus in the Turpan basin should also include deep structures within the Carboniferous-Permian strata and subtle, low magnitude anticlines and stratigraphic traps within thr Triassic-Jurassic sections. (author)

  11. Study on coal dust wettability measurement using cold briquetting technique

    Li, M.; Xu, H.; Shu, X. [North China Institute of Science and Technology, Beijing (China). Department of Resource and Environmental Engineering

    2008-12-15

    Quantitative measuring of coal dust wettability is essential for the research and development of chemical coal dust suppressants in the field of dust control with wetting-agent-added water. The causes of low repeat rate and poor consistency in present lab testing of coal dust wettability are discussed. The influence of different briquetting pressure (from 0 to 6.5108 Pa) on the wet behavior of coal dust is investigated as a new way to quantitatively evaluate coal dust wettability. The study shows that there is a fairly high coincidence between the coal dust wettability data measured by the briquetting technique and the results gained from the lab dust suppression tests using an MCYZ apparatus designed by the authors. 9 refs., 8 figs., 2 tabs.

  12. Dynamic measurement of coal thermal properties and elemental composition of volatile matter during coal pyrolysis

    Rohan Stanger

    2014-01-01

    Full Text Available A new technique that allows dynamic measurement of thermal properties, expansion and the elemental chemistry of the volatile matter being evolved as coal is pyrolysed is described. The thermal and other properties are measured dynamically as a function of temperature of the coal without the need for equilibration at temperature. In particular, the technique allows for continuous elemental characterisation of tars as they are evolved during pyrolysis and afterwards as a function of boiling point. The technique is demonstrated by measuring the properties of maceral concentrates from a coal. The variation in heats of reaction, thermal conductivity and expansion as a function of maceral composition is described. Combined with the elemental analysis, the results aid in the interpretation of the chemical processes contributing to the physical and thermal behaviour of the coal during pyrolysis. Potential applications in cokemaking studies are discussed.

  13. Dynamic evolution characteristics of mining-induced fractures in overlying strata detected by radon

    Zhang Wei; Ma Liqiang; Wang Xufeng; Fang Gangwei; Zhang Dongsheng

    2011-01-01

    For environment protection in mining areas in northwest China, we developed a CTSRM (comprehensive test system by radon measurement) to measure radon radioactivity and detect dynamic evolution characteristics of mining-induced fractures in overlying strata. It was used to simulate the relationship between the dynamic evolution characteristics and radon concentrations of No. 33201 coalface at Bulianta coal mine in Inner Mongolia, and feasibility of the method was validate. (authors)

  14. Measurement of reflectance of coal macerals: its automation and significance

    Davis, A.

    1978-06-01

    A prime objective of the Pennsylvania State University's DOE program is the characterization of 1,300 samples of U.S. coals. Reflectance determination plays a major role in meeting this objective, because it is used as an accurate rank index both to select coals for testing and to investigate property-behavior interrelationships using the Penn State/DOE Coal Data Base. Reflectances of coal macerals are related to their refractive and absorptive indices by the Beer equation; the refractive index of the medium and the wavelength of light need to be specified. Determinations usually are made in immersion oil at 546 nm. Properties of vitrinite make it the most suitable maceral for these measurements, but the variety of vitrinite selected may depend upon the intended application. Vitrinite reflectance is considered to be dependent upon the degree of aromatization of its structural units. Although some of the earlier investigators believed that the reflectance of coals increased in a discontinuous, stepped manner as their rank increased, the bulk of assembled data suggests that the change is continuous. Some recent results indicate that there may be more than one coalification track for coals with different geological histories, resulting in displacement from the general trend. Several techniques have been employed to determine the optical properties of coal constituents. Usual comparative method involves the use of a microscope photometer to compare the intensity of light reflected by particles within a polished pellet of coal to that of a glass or synthetic mineral standard. Because coal is anisotropic it is common to measure either maximum reflectance in polarized light or random reflectance in non-polarized light. Various eqipment modifications and accessories have been used to improve the ease of measuring maximum reflectance.

  15. Study on the Rule of Super Strata Movement and Subsidence

    Yao, Shunli; Yuan, Hongyong; Jiang, Fuxing; Chen, Tao; Wu, Peng

    2018-01-01

    The movement of key strata is related to the safety of the whole earth’s surface for coal mining under super strata. Based on the key strata theory, the paper comprehensively analyzes the characteristics of the subsidence before and after the instability of the super strata by studing through FLAC3D and microseismic dynamic monitoring of the surface rock movement observation. The stability of the super strata movement is analyzed according to the characteristic value of the subsidence. The subsidence law and quantitative indexes under the control of the super rock strata that provides basis for the prevention and control of surface risk, optimize mining area and face layout and reasonably set mining boundary around mining area. It provides basis for the even growth of mine safety production and regional public safety.

  16. A new type of Nb (Ta)-Zr(Hf)-REE-Ga polymetallic deposit in the late Permian coal-bearing strata, eastern Yunnan, southwestern China: Possible economic significance and genetic implications

    Dai, Shifeng; Wang, Xibo; Luo, Yangbing; Song, Zhentao; Ren, Deyi [State Key Laboratory of Coal Resources and Safe Mining, China University of Mining and Technology, Beijing 100083 (China); Zhou, Yiping; Zhang, Mingquan; Wang, Jumin; Song, Xiaolin; Yang, Zong [Yunnan Institute of Coal Geology Prospection, Kunming 650218 (China); Jiang, Yaofa [Xuzhou Institute of Architectural Technology, Xuzhou 221116 (China)

    2010-07-01

    This paper describes a new type of Nb(Ta)-Zr(Hf)-REE-Ga polymetallic deposit of volcanic origin in the late Permian coal-bearing strata of eastern Yunnan, southwestern China. Well logging data (especially natural gamma-ray), geochemical data (high concentrations of Nb, Ta, Zr, Hf, REE, and Ga) and mineralogical compositions (Nb(Ta)-, Zr(Hf)-, or REE-bearing minerals rarely observed), together with the volcanic lithological characteristics indicate that there are thick (1-10 m, mostly 2-5 m) ore beds in the lower Xuanwei Formation (late Permian) in eastern Yunann of southwestern China. The ore beds are highly enriched in (Nb,Ta){sub 2}O{sub 5} (302-627 ppm), (Zr,Hf)O{sub 2} (3805-8468 ppm), REE (oxides of La-Lu + Y) (1216-1358 ppm), and Ga (52.4-81.3 ppm). The ore beds are mainly composed of quartz, mixed-layer illite-smectite, kaolinite, berthierine, and albite. Four types of ore beds in the study area were identified, namely, clay altered volcanic ash, tuffaceous clay, tuff, and volcanic breccia. Preliminary studies suggest that the high concentrations of otherwise rare metals were mainly derived from the alkalic pyroclastic rocks. The modes of occurrence, spatial distribution, and enrichment mechanism of the rare metals, however, require further study. (author)

  17. Clay Mineralogy of Coal-Hosted Nb-Zr-REE-Ga Mineralized Beds from Late Permian Strata, Eastern Yunnan, SW China: Implications for Paleotemperature and Origin of the Micro-Quartz

    Lixin Zhao

    2016-05-01

    Full Text Available The clay mineralogy of pyroclastic Nb(Ta-Zr(Hf-REE-Ga mineralization in Late Permian coal-bearing strata from eastern Yunnan Province; southwest China was investigated in this study. Samples from XW and LK drill holes in this area were analyzed using XRD (X-ray diffraction and SEM (scanning electronic microscope. Results show that clay minerals in the Nb-Zr-REE-Ga mineralized samples are composed of mixed layer illite/smectite (I/S; kaolinite and berthierine. I/S is the major component among the clay assemblages. The source volcanic ashes controlled the modes of occurrence of the clay minerals. Volcanic ash-originated kaolinite and berthierine occur as vermicular and angular particles, respectively. I/S is confined to the matrix and is derived from illitization of smectite which was derived from the original volcanic ashes. Other types of clay minerals including I/S and berthierine precipitated from hydrothermal solutions were found within plant cells; and coexisting with angular berthierine and vermicular kaolinite. Inferred from the fact that most of the I/S is R1 ordered with one case of the R3 I/S; the paleo-diagenetic temperature could be up to 180 °C but mostly 100–160 °C. The micro-crystalline quartz grains (<10 µm closely associated with I/S were observed under SEM and were most likely the product of desiliconization during illitization of smectite.

  18. Analysis of gob gas venthole production performances for strata gas control in longwall mining.

    Karacan, C Özgen

    2015-10-01

    Longwall mining of coal seams affects a large area of overburden by deforming it and creating stress-relief fractures, as well as bedding plane separations, as the mining face progresses. Stress-relief fractures and bedding plane separations are recognized as major pathways for gas migration from gas-bearing strata into sealed and active areas of the mines. In order for strata gas not to enter and inundate the ventilation system of a mine, gob gas ventholes (GGVs) can be used as a methane control measure. The aim of this paper is to analyze production performances of GGVs drilled over a longwall panel. These boreholes were drilled to control methane emissions from the Pratt group of coals due to stress-relief fracturing and bedding plane separations into a longwall mine operating in the Mary Lee/Blue Creek coal seam of the Upper Pottsville Formation in the Black Warrior Basin, Alabama. During the course of the study, Pratt coal's reservoir properties were integrated with production data of the GGVs. These data were analyzed by using material balance techniques to estimate radius of influence of GGVs, gas-in-place and coal pressures, as well as their variations during mining. The results show that the GGVs drilled to extract gas from the stress-relief zone of the Pratt coal interval is highly effective in removing gas from the Upper Pottsville Formation. The radii of influence of the GGVs were in the order of 330-380 m, exceeding the widths of the panels, due to bedding plane separations and stress relieved by fracturing. Material balance analyses indicated that the initial pressure of the Pratt coals, which was around 648 KPa when longwall mining started, decreased to approximately 150 KPa as the result of strata fracturing and production of released gas. Approximately 70% of the initial gas-in-place within the area of influence of the GGVs was captured during a period of one year.

  19. Measurement and modeling of advanced coal conversion processes

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G.; Smoot, L.D.; Brewster, B.S. (Advanced Fuel Research, Inc., East Hartford, CT (United States) Brigham Young Univ., Provo, UT (United States))

    1991-01-01

    The overall objective of this program is the development of predictive capability for the design, scale up, simulation, control and feedstock evaluation in advanced coal conversion devices. This program will merge significant advances made in measuring and quantitatively describing the mechanisms in coal conversion behavior. Comprehensive computer codes for mechanistic modeling of entrained-bed gasification. Additional capabilities in predicting pollutant formation will be implemented and the technology will be expanded to fixed-bed reactors.

  20. Coal

    Teissie, J.; Bourgogne, D. de; Bautin, F.

    2001-12-01

    Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

  1. Slope stability probability classification, Waikato Coal Measures, New Zealand

    Lindsay, P.; Campbell, R.; Fergusson, D.A.; Ferm, J.C.; Gillard, G.R.; Moore, T.A. [CRL Energy Ltd., Christchurch (New Zealand)

    1999-07-01

    Ferm classified lithological units have been identified and described in the Waikato Coal Measures in open pits in the Waikato coal region. These lithological units have been classified geotechnically with mechanical tests and discontinuity measurements. Using these measurements, slope stability probability classification (SSPC) have been quantified based on an adaption of Hack's SSPC system which places less influence on rock quality designation and unconfined compressive strength than previous rock mass rating systems. An attempt has been made to modify the Hack weathering susceptibility rating by using chemical index of alteration values from XRF major element analysis. Another major component of this adapted SSPC system is the inclusion of rock moisture content effects on slope stability. The paper explains the systematic initial approach of using the adapted SSPC system to classify slope stability in the Waikato open pit coal mines. The XRF major element results obtained for lithologies in the Waikato coal region may be a useful mine management tool to quantify stratigraphic thickness and palaeoweathering from wash drill cuttings. 14 refs., 7 figs., 3 tabs.

  2. Mercury emission, control and measurement from coal combustion

    Pan, Wei-Ping [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering; Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Cao, Yan [Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Zhang, Kai [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering

    2013-07-01

    Coal-fired electric power generation accounts for 65% of U.S. emissions of sulfur dioxide (SO2), 22% of nitrogen oxides (NOx), and 37% of mercury (Hg). The proposed Clear Air Interstate Rule (CAIR) and Clean Air Mercury Rule (CAMR) will attempt to regulate these emissions using a cap-and-trade program to replace a number of existing regulatory requirements that will impact this industry over the next decade. Mercury emissions remain the largest source that has not yet been efficiently controlled, in part because this is one of the most expensive to control. Mercury is a toxic, persistent pollutant that accumulates in the food chain. During the coal combustion process, when both sampling and accurate measurements are challenging, we know that mercury is present in three species: elemental, oxidized and particulate. There are three basic types of mercury measurement methods: Ontario Hydro Method, mercury continuous emission monitoring systems (CEMS) and sorbent-based monitoring. Particulate mercury is best captured by electrostatic precipitators (ESP). Oxidized mercury is best captured in wet scrubbers. Elemental mercury is the most difficult to capture, but selective catalytic reduction units (SCRs) are able to convert elemental mercury to oxidized mercury allowing it to be captured by wet flue gas desulfurization (FGD). This works well for eastern coals with high chlorine contents, but this does not work well on the Wyoming Powder River Basin (PRB) coals. However, no good explanation for its mechanism, correlations of chlorine content in coal with SCR performance, and impacts of higher chlorine content in coal on FGD re-emission are available. The combination of SCR and FGD affords more than an 80% reduction in mercury emissions in the case of high chlorine content coals. The mercury emission results from different coal ranks, boilers, and the air pollution control device (APCD) in power plant will be discussed. Based on this UAEPA new regulation, most power plants

  3. Development and application of a radiometric method of measurement (Heger probe) for characterizing clastic rock strata in exposures

    Koch, G.

    1984-01-01

    The radiometric image of a stratigraphic exposure profile was to be logged. The method of measurement was tested on clastic sediments of the Tertiary (Saudi Arabia) and Bunter (Northern Germany). The well-tried scintillometer technique was supplemented by modern technological means supplied by a prospecting company (Gewerkschaft Brunhilde). The probe applied was specifically developped for stratigraphic purposes. (orig./HP) [de

  4. Direct measurement of oxygen in brown coals and carbochemical products by means of fast neutron analysis

    Raeppel, P.; Foerster, H.

    1990-01-01

    Analyses of elemental oxygen by means of fast neutron activation permit high-accuracy measurements of oxygen concentrations in East German brown coal; this applies to run-of-mine brown coal as well as to demineralized brown coal. The relative error was 4% in the first case and 2% in the latter case. Pre-washing with 1n ammonium acetate solution permits direct analyses of the oxygen bonded to the coal minerals. The method is applicable to other carbonaceous materials, e.g. coal ashes, solid hydrogenation residues, cokes, coal extracts, asphaltenes, oils, etc., at oxygen concentrations of 1-50%. (orig.) [de

  5. Slope stability probability classification, Waikato Coal Measures, New Zealand

    Lindsay, P.; Gillard, G.R.; Moore, T.A. [CRL Energy, PO Box 29-415, Christchurch (New Zealand); Campbell, R.N.; Fergusson, D.A. [Solid Energy North, Private Bag 502, Huntly (New Zealand)

    2001-01-01

    Ferm classified lithological units have been identified and described in the Waikato Coal Measures in open pits in the Waikato coal region. These lithological units have been classified geotechnically by mechanical tests and discontinuity measurements. Using these measurements slope stability probability classifications (SSPC) have been quantified based on an adaptation of Hack's [Slope Stability Probability Classification, ITC Delft Publication, Enschede, Netherlands, vol. 43, 1998, 273 pp.] SSPC system, which places less influence on rock quality designation and unconfined compressive strength than previous slope/rock mass rating systems. The Hack weathering susceptibility rating has been modified by using chemical index of alteration values determined from XRF major element analyses. Slaking is an important parameter in slope stability in the Waikato Coal Measures lithologies and hence, a non-subjective method of assessing slaking in relation to the chemical index of alteration has been introduced. Another major component of this adapted SSPC system is the inclusion of rock moisture content effects on slope stability. The main modifications of Hack's SSPC system are the introduction of rock intact strength derived from the modified Mohr-Coulomb failure criterion, which has been adapted for varying moisture content, weathering state and confining pressure. It is suggested that the subjectivity in assessing intact rock strength within broad bands in the initial SSPC system is a major weakness of the initial system. Initial results indicate a close relationship between rock mass strength values, calculated from rock mass friction angles and rock mass cohesion values derived from two established rock mass classification methods (modified Hoek-Brown failure criteria and MRMR) and the adapted SSPC system. The advantage of the modified SSPC system is that slope stability probabilities based on discontinuity-independent and discontinuity-dependent data and a

  6. Thermal surface characteristics of coal fires 1 results of in-situ measurements

    Zhang, Jianzhong; Kuenzer, Claudia

    2007-12-01

    Natural underground coal fires are fires in coal seams occurring subsurface. The fires are ignited through a process named spontaneous combustion, which occurs based on a natural reaction but is usually triggered through human interaction. Coal mining activities expose coal to the air. This leads to the exothermal oxidation of the carbon in the coal with the air's oxygen to CO 2 and - under certain circumstances - to spontaneous combustion. Coal fires occur in many countries world wide - however, currently the Chinese coal mining industry faces the biggest problems with coal fires. Coal fires destroy the valuable resource coal and furthermore lead to many environmental degradation phenomena such as the deterioration of surrounding vegetation, land subsidence and the emission of toxic gasses (CO, N 2O). They additionally contribute to the emission of green house relevant gasses such as CO 2 and CH 4 to the atmosphere. In this paper we present thermal characteristics of coal fires as measured in-situ during a field campaign to the Wuda coal fire area in south-central Inner Mongolia, China. Thermal characteristics include temperature anomaly measurements at the surface, spatial surface temperature profiles of fire areas and unaffected background areas, diurnal temperature profiles, and temperature measurements inside of coal fire induced cracks in the overlying bedrock. For all the measurements the effects of uneven solar heating through influences of slope and aspect are considered. Our findings show that coal fires result in strong or subtle thermal surface anomalies. Especially the latter can easily be influenced by heating of the surrounding background material through solar influences. Temperature variation of background rocks with different albedo, slope, aspect or vegetation cover can substantially influence the detectability of thermal anomalies. In the worst case coal fire related thermal anomalies can be completely masked by solar patterns during the daytime

  7. Measurements of noise from rotary coal unloading operations

    Adams, T.S.; Bilello, M.A.

    1991-01-01

    In the licensing effort for a coal-fired power plant in the northeast United States, noise related to delivery and unloading of coal by train was identified as a significant concern to the nearby community. Specific issues included locomotive noise, the banging noises caused by railcar couplings during the start and stop cycles of the unloading operation, wheel squeal in the curves of the rail loop, and rotary coal unloader noises. This paper reports that a literature review provided adequate information on idling locomotive noise but very little on the other noise sources. Coupling impact noise was well documented for railcars actually being coupled at various speeds but not for coupled trains during start and stop operations. Wheel squeal was well documented by subway trains travelling at normal speeds, but nothing could be found for wheel squeal during very slow train movement as occurs during unloading. Similarly, adequate information was available for unenclosed rotary unloaders but not for enclosed unloaders. Consequently, actual noise measurements of a similar enclosed facility, and the associated train movements, were undertaken to obtain data more directly applicable to the planned facility

  8. Coal forming conditions for coal seams and coal measures of the Heshan Group Upper Permian Series in Guangxi Province (part 1)

    Li, Y.

    1980-10-01

    Coal forming conditions for the coal measures of the Heshan Group are discussed based on the analysis of the historical background and paleogeographical environment of the Permian in Guangxi Province. The roof, floor, and partings of the seams are composed of algal micritic limestone, therefore affirming that the central part of Guangxi Province in the late Permian was a typical epi-continental sea. The compensative deposit of algea on the carbonate platform in very shallow water created the conditions for the occurrence of the peat swamp and established the supra-tidal swampy facies. The environment for the accumulation of the major coal seams are analyzed. (In Chinese)

  9. Study on fluid-solid coupling mechanism for water resistance effect of coal floor based on different combination of rock strata%基于不同岩层组合对底板阻水效应的流固耦合机理研究

    翟晓荣; 张红梅; 窦仲四; 吴基文; 沈书豪; 周盛全

    2016-01-01

    为了探究不同岩层组合底板对承压水的阻隔效果,以淮北矿区下组煤底板为研究对象,建立了三种不同组合特征底板模型.基于FISH语言对FLAC3D软件进行二次开发,对流固耦合条件下不同组合特征底板采动应力及围岩渗透性进行了综合分析.结果表明:流固耦合条件下,底板采后应力转换点深度较不考虑底板水压条件下加深,且底板深部出现了明显的卸压现象;硬软型底板采后卸荷程度及应力转换点降幅最大,而软硬相间型底板受最小;硬软型底板采后渗透性提高4.5倍,而软硬相间型底板仅提高1.4倍,研究结果揭示出软硬相间岩层组合底板阻水效果最好,而硬软型底板最差.%To investigate the resistance effect of coal floor with different combination of rock strata on confined water , taking the coal floor of lower coal group in Huaibei mining area as research object , three coal floor models with different combination characteristics were established .The secondary development was conducted on FLAC 3D software based on FISH language , then the comprehensive analysis on the mining stress of coal floor and the permeability of surrounding rock with different com -bination characteristics under the condition of fluid-solid coupling was carried out .The results showed that under the condi-tion of fluid-solid coupling , the depth of stress transition point for coal floor after mining was larger than that without consid -ering the condition of floor water pressure , and the obvious pressure relief phenomenon appeared in the deep floor .The de-creasing amplitude of unloading degree and stress transition point for hard -soft type coal floor after mining were the largest , while those for alternated soft-hard type coal floor were the smallest .The permeability of hard-soft type coal floor after mining increased by 4.5 times, while that of alternated soft-hard type coal floor increased by 1.5 times only.It revealed that

  10. Temporal measurements and kinetics of selenium release during coal combustion and gasification in a fluidized bed

    Shen, Fenghua; Liu, Jing; Zhang, Zhen; Yang, Yingju

    2016-01-01

    Highlights: • The temporal release of Se from coal combustion and gasification was measured. • Kinetic laws for Se release from coal combustion and gasification were determined. • The influences of temperature and chemical composition of flue gas were clarified. • The interactions of Se species with mineral affect the release kinetics of Se. - Abstract: The temporal release of selenium from coal during combustion and gasification in a fluidized bed was measured in situ by an on-line analysis system of trace elements in flue gas. The on-line analysis system is based on an inductively coupled plasma optical emission spectroscopy (ICP-OES), and can measure concentrations of trace elements in flue gas quantitatively and continuously. The results of on-line analysis suggest that the concentration of selenium in flue gas during coal gasification is higher than that during coal combustion. Based on the results of on-line analysis, a second-order kinetic law r(x) = 0.94e −26.58/RT (−0.56 x 2 −0.51 x + 1.05) was determined for selenium release during coal combustion, and r(x) = 11.96e −45.03/RT (−0.53 x 2 −0.56 x + 1.09) for selenium release during coal gasification. These two kinetic laws can predict respectively the temporal release of selenium during coal combustion and gasification with an acceptable accuracy. Thermodynamic calculations were conducted to predict selenium species during coal combustion and gasification. The speciation of selenium in flue gas during coal combustion differs from that during coal gasification, indicating that selenium volatilization is different. The gaseous selenium species can react with CaO during coal combustion, but it is not likely to interact with mineral during coal gasification.

  11. Depositional controls on coal distribution and quality in the Eocene Brunner Coal Measures, Buller Coalfield, South Island, New Zealand

    Flores, R.M.; Sykes, R.

    1996-01-01

    The Buller Coalfield on the West Coast of the South Island, New Zealand, contains the Eocene Brunner Coal Measures. The coal measures unconformably overlie Paleozoic-Cretaceous basement rocks and are conformably overlain by, and laterally interfinger with, the Eocene marine Kaiata Formation. This study examines the lithofacies frameworks of the coal measures in order to interpret their depositional environments. The lower part of the coal measures is dominated by conglomeratic lithofacies that rest on a basal erosional surface and thicken in paleovalleys incised into an undulating peneplain surface. These lithofacies are overlain by sandstone, mudstone and organic-rich lithofacies of the upper part of the coal measures. The main coal seam of the organic-rich lithofacies is thick (10-20 m), extensive, locally split, and locally absent. This seam and associated coal seams in the Buller Coalfield are of low- to high-volatile bituminous rank (vitrinite reflectance between 0.65% and 1.75%). The main seam contains a variable percentage of ash and sulphur. These values are related to the thickening and areal distribution of the seam, which in turn, were controlled by the nature of clastic deposition and peat-forming mire systems, marine transgression and local tidal incursion. The conglomeratic lithofacies represent deposits of trunk and tributary braided streams that rapidly aggraded incised paleovalleys during sea-level stillstands. The main seam represents a deposit of raised mires that initially developed as topogenous mires on abandoned margins of inactive braidbelts. Peat accumulated in mires as a response to a rise in the water table, probably initially due to gradual sea-level rise and climate, and the resulting raised topography served as protection from floods. The upper part of the coal measures consists of sandstone lithofacies of flu vial origin and bioturbated sandstone, mudstone and organic-rich lithofacies, which represent deposits of paralic (deltaic

  12. Strata control in mineral engineering

    Bieniawski, Z.T.

    1986-01-01

    This book covers the state-of-the-art of strata control practice both in the United States and abroad with respect to strata reinforcement by rock bolting, long wall mining technology and innovations in energy development, such as mining for oil and tunneling for storage of high-level nuclear waste in deep underground repositories. It features coverage of design concepts in rock engineering and rockbolt systems, stability of rock pillars, rockbursts, shaft design and construction and a detailed consideration of mineral and energy needs in the United States

  13. Measurement and modeling of advanced coal conversion processes

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. (Advanced Fuel Research, Inc., East Hartford, CT (United States)); Smoot, L.D.; Brewster, B.S. (Brigham Young Univ., Provo, UT (United States))

    1991-01-01

    The objective of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines.

  14. Measurement and modeling of advanced coal conversion processes

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. (Advanced Fuel Research, Inc., East Hartford, CT (United States)); Smoot, L.D.; Brewster, B.S. (Brigham Young Univ., Provo, UT (United States))

    1991-09-25

    The objectives of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines. (VC)

  15. Physical Experiments on the Deformation of Strata with Different Properties Induced by Underground Mining

    Haifeng Hu

    2016-03-01

    Full Text Available Underground mining can cause ground and strata movements, which in turn cause damage to houses and the landscape. The different characteristics and properties of the strata encountered during mining can also result in corresponding deformation. In order to study the deformation and damage rules of strata which are composed of unconsolidated soil and bedrock induced by underground coal mining, a physical model that employs material sand, lime, and gypsum with water was utilized firstly to simulate strata and ground movements. Then overlying strata with different properties were created according to the corresponding ratio of the mixed material, physical models under two conditions (i.e., thick soil layer and thin bedrock, and thin soil layer and thick bedrock were set up. Lastly underground coal extraction was conducted using the proposed models. Results show that the proportion of unconsolidated soil layer in the overlying strata is the key factor that determines the significant differences in the movement of strata under the two special conditions. When the ratio of the soil layer is large, the unconsolidated soil layer is loaded on the bedrock; the bedrock is thus forced to move down, and the compression rate of the broken strata is increased. The soil layer follows the bedrock as an integral movement to subsidence. When the ratio of the soil layer is small, the load on the strata is small, but the structural function of the strata is obvious and the fraction degree in the strata is developed. The obtained results in this study can be applied to support mine planning in the aspect of ground damage evaluation.

  16. Measurement and modeling of advanced coal conversion processes, Volume II

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. [and others

    1993-06-01

    A two dimensional, steady-state model for describing a variety of reactive and nonreactive flows, including pulverized coal combustion and gasification, is presented. The model, referred to as 93-PCGC-2 is applicable to cylindrical, axi-symmetric systems. Turbulence is accounted for in both the fluid mechanics equations and the combustion scheme. Radiation from gases, walls, and particles is taken into account using a discrete ordinates method. The particle phase is modeled in a lagrangian framework, such that mean paths of particle groups are followed. A new coal-general devolatilization submodel (FG-DVC) with coal swelling and char reactivity submodels has been added.

  17. Evolution characteristics and application of diamondoids in coal measures

    Chenchen Fang

    2016-02-01

    Full Text Available As diamondoids have been used to evaluate petroleum and source rocks widely; their origin, evolution, and distribution in petroleum as well as source rocks have attracted ever more attention. Having finished the pyrolysis simulation experiment of the coal measure mudrocks from Xujiahe Formation, Sichuan Basin, results indicated that with the equivalent vitrinite reflectance (EasyRo increasing, diamondoids experience generation (1.0%  1.5%. Throughout the simulation experiment, diamondoid parameters MAI, EAI, and TMAI-1 kept good relationships with maturity within the range of EasyRo 1.5%–2.5%, 1.0%–2.5%, and 1.5%–2.5% respectively, with all of the correlation coefficient (R2 being above 0.7844, this indicated that these parameters can be used to evaluate maturity at these ranges. In addition, the yield ratios A/D, MA/MD, DMA/DMD, and As/Ds also kept good relationships with maturity at the range of EasyRo 1.2%–2.5%, with all of the R2 above 0.9236, this indicated that these ratios can be used to evaluate maturity index at this range.

  18. Peronosporomycetes (Oomycota from a Middle Permian permineralised peat within the Bainmedart Coal Measures, Prince Charles Mountains, Antarctica.

    Ben J Slater

    Full Text Available The fossil record of Peronosporomycetes (water moulds is rather sparse, though their distinctive ornamentation means they are probably better reported than some true fungal groups. Here we describe a rare Palaeozoic occurrence of this group from a Guadalupian (Middle Permian silicified peat deposit in the Bainmedart Coal Measures, Prince Charles Mountains, Antarctica. Specimens are numerous and comprise two morphologically distinct kinds of ornamented oogonia, of which some are attached to hyphae by a septum. Combresomyces caespitosus sp. nov. consists of spherical oogonia bearing densely spaced, long, hollow, slender, conical papillae with multiple sharply pointed, strongly divergent, apical branches that commonly form a pseudoreticulate pattern under optical microscopy. The oogonia are attached to a parental hypha by a short truncated stalk with a single septum. Combresomyces rarus sp. nov. consists of spherical oogonia bearing widely spaced, hollow, broad, conical papillae that terminate in a single bifurcation producing a pair of acutely divergent sharply pointed branches. The oogonium bears a short truncate extension where it attaches to the parental hypha. We propose that similarities in oogonium shape, size, spine morphology and hyphal attachment between the Permian forms from the Prince Charles Mountains and other reported Peronosporomycetes from Devonian to Triassic strata at widely separated localities elsewhere in the world delimit an extinct but once cosmopolitan Palaeozoic to early Mesozoic branch of the peronosporomycete clade. We name this order Combresomycetales and note that it played an important role in late Palaeozoic and early Mesozoic peatland ecosystems worldwide.

  19. Mechanism of rigid overlaying of carboniferous strata failure in face mining in the case of multiseams deposit

    Jiránková, E.; Staš, Lubomír; Kajzar, Vlastimil; Doležalová, Hana

    2013-01-01

    Roč. 10, č. 2 (2013), s. 189-195 ISSN 1214-9705 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MV VG20102014034 Institutional support: RVO:68145535 Keywords : subsidence trough * rock mass * overlaying strata * longwall mining * tensor stress measurement Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 0.667, year: 2013 http://www.irsm.cas.cz/materialy/acta_content/2013_02/acta_170_08_Jirankova_189-195.pdf

  20. Measurement and modeling of advanced coal conversion processes, Volume III

    Ghani, M.U.; Hobbs, M.L.; Hamblen, D.G. [and others

    1993-08-01

    A generalized one-dimensional, heterogeneous, steady-state, fixed-bed model for coal gasification and combustion is presented. The model, FBED-1, is a design and analysis tool that can be used to simulate a variety of gasification, devolatilization, and combustion processes. The model considers separate gas and solid temperatures, axially variable solid and gas flow rates, variable bed void fraction, coal drying, devolatilization based on chemical functional group composition, depolymerization, vaporization and crosslinking, oxidation, and gasification of char, and partial equilibrium in the gas phase.

  1. A new radiometric instrument designed to measure the parameters of bituminous coal on transport belts

    Kubicek, P.

    1993-01-01

    A new radiometric instrument developed in Czechoslovakia, for the measurement of ash content of bituminous coal, and for the determination of approximate values of moisture and weight is described. (Author)

  2. Analysis on the Initial Cracking Parameters of Cross-Measure Hydraulic Fracture in Underground Coal Mines

    Yiyu Lu

    2015-07-01

    Full Text Available Initial cracking pressure and locations are important parameters in conducting cross-measure hydraulic fracturing to enhance coal seam permeability in underground coalmines, which are significantly influenced by in-situ stress and occurrence of coal seam. In this study, stress state around cross-measure fracturing boreholes was analyzed using in-situ stress coordinate transformation, then a mathematical model was developed to evaluate initial cracking parameters of borehole assuming the maximum tensile stress criterion. Subsequently, the influences of in-situ stress and occurrence of coal seams on initial cracking pressure and locations in underground coalmines were analyzed using the proposed model. Finally, the proposed model was verified with field test data. The results suggest that the initial cracking pressure increases with the depth cover and coal seam dip angle. However, it decreases with the increase in azimuth of major principle stress. The results also indicate that the initial cracking locations concentrated in the second and fourth quadrant in polar coordinate, and shifted direction to the strike of coal seam as coal seam dip angle and azimuth of maximum principle stress increase. Field investigation revealed consistent rule with the developed model that the initial cracking pressure increases with the coal seam dip angle. Therefore, the proposed mathematical model provides theoretical insight to analyze the initial cracking parameters during cross-measure hydraulic fracturing for underground coalmines.

  3. Revised stratigraphy of the Permian Bainmedart coal measures, northern Prince Charles Mountains, east Antarctica

    McLoughlin, S.; Drinnan, A.N. [University of Melbourne, Parkville, Vic. (Australia). School of Botany

    1997-05-01

    The Bainmedart Coal Measures constitute the middle portion of the Permian-Triassic Amery Group, which represents the only substantial Palaeozoic-Mesozoic sedimentary succession exposed in eastern Antarctica outside the Transantarctic Mountains. The coal measures overlie alluvial fan deposits of the Radok Conglomerate and are conformably overlain by the dominantly fluviatile Flagstone Bench Formation. The coal measures were deposited within alluvial settings dominated by north to northeasterly flowing, low-sinuosity rivers chiefly confined to broad, fault-bounded, valleys of the Lambert Graben, a major late Palaeozoic to early Mesozoic failed rift system. Both climatic and local tectonic factors are considered to have been the major influences on the pattern of coal measure sedimentation. Recent mapping has identified a much greater thickness of sediments within the coal measures than had been inferred previously. The Bainmedart Coal Measures are formally subdivided into six members. In ascending stratigraphic order these are: Dart Fields Conglomerate Member ({lt} 3m thick), Toploje Member (300 m thick), Dragons Teeth Member (15-25 m thick), Glossopteris Gully Member (670 m thick), Grainer Member (350 m thick), acid McKinnon Member (530 m thick).

  4. Aeromagnetic anomalies over faulted strata

    Grauch, V.J.S.; Hudson, Mark R.

    2011-01-01

    High-resolution aeromagnetic surveys are now an industry standard and they commonly detect anomalies that are attributed to faults within sedimentary basins. However, detailed studies identifying geologic sources of magnetic anomalies in sedimentary environments are rare in the literature. Opportunities to study these sources have come from well-exposed sedimentary basins of the Rio Grande rift in New Mexico and Colorado. High-resolution aeromagnetic data from these areas reveal numerous, curvilinear, low-amplitude (2–15 nT at 100-m terrain clearance) anomalies that consistently correspond to intrasedimentary normal faults (Figure 1). Detailed geophysical and rock-property studies provide evidence for the magnetic sources at several exposures of these faults in the central Rio Grande rift (summarized in Grauch and Hudson, 2007, and Hudson et al., 2008). A key result is that the aeromagnetic anomalies arise from the juxtaposition of magnetically differing strata at the faults as opposed to chemical processes acting at the fault zone. The studies also provide (1) guidelines for understanding and estimating the geophysical parameters controlling aeromagnetic anomalies at faulted strata (Grauch and Hudson), and (2) observations on key geologic factors that are favorable for developing similar sedimentary sources of aeromagnetic anomalies elsewhere (Hudson et al.).

  5. Measurement and modeling of advanced coal conversion processes. Annual report, October 1990--September 1991

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G.; Smoot, L.D.; Brewster, B.S. [Advanced Fuel Research, Inc., East Hartford, CT (United States)]|[Brigham Young Univ., Provo, UT (United States)

    1991-12-31

    The overall objective of this program is the development of predictive capability for the design, scale up, simulation, control and feedstock evaluation in advanced coal conversion devices. This program will merge significant advances made in measuring and quantitatively describing the mechanisms in coal conversion behavior. Comprehensive computer codes for mechanistic modeling of entrained-bed gasification. Additional capabilities in predicting pollutant formation will be implemented and the technology will be expanded to fixed-bed reactors.

  6. Intrinsic reaction kinetics of coal char combustion by direct measurement of ignition temperature

    Kim, Ryang-Gyoon; Jeon, Chung-Hwan

    2014-01-01

    A wire heating reactor that can use a synchronized experimental method was developed to obtain the intrinsic kinetics of large coal char particles ranging in size from 0.4 to 1 mm. This synchronization system consists of three parts: a thermocouple wire for both heating and direct measurement of the particle temperature, a photodetector sensor for determining ignition/burnout points by measuring the intensity of luminous emission from burning particles, and a high-speed camera–long-distance microscope for observing and recording the movement of luminous zone directly. Coal char ignition was found to begin at a spot on the particle's external surface and then moved across the entire particle. Moreover, the ignition point determined according to the minimum of dT/dt is a spot point and not a full growth point. The ignition temperature of the spot point rises as the particle diameter increases. A spot ignition model, which describes the ignition in terms of the internal conduction and external/internal oxygen diffusion, was then developed to evaluate the intrinsic kinetics and predict the ignition temperature of the coal char. Internal conduction was found to be important in large coal char particles because its effect becomes greater than that of oxygen diffusion as the particle diameter increases. In addition, the intrinsic kinetics of coal char obtained from the spot ignition model for two types of coal does not differ significantly from the results of previous investigators. -- Highlights: • A novel technique was used to measure the coal char particle temperature. • The ignition point determined from a dT/dt minimum is a spot ignition point. • A spot ignition model was suggested to analyze the intrinsic reaction kinetics of coal char. • Internal conduction has to be considered in order to evaluate the intrinsic kinetics for larger particle (above 1 mm)

  7. A study on the measurement of coal moisture by the neutron method

    Ma Yonghe

    1985-01-01

    The paper reports the result of measuring coal moisture by the neutron method. A deducting intercept method is used to eliminate the effects of the structural hydrogen and the matrix effect. A measuring device has been developed and its measuring accuracy is less than 1%

  8. Signature recognition for rift structures of different sediment strata in ordos basin

    Zhao Xigang

    2006-10-01

    The rift structure weak information of high Bouguer gravity anomaly data among different Sediment strata are extracted By the horizontal gradient Maximum modulus, the wavelet variation, stripped gravity anomaly of basement and interfaces above/under researched layer, image processing method. So the linear rift structures of different Sediment strata are recognized on data images, such as Cretaceous, Jurassic, Triassic, Permian and Carboniferous, Ordovician System. Development rifts of different Sediment strata occur in stereo structure with quasi-uniform spacing, the rift density of above Sediment stratum is more than lower in different Sediment strata, but the north rift density of the same Sediment stratum is less than south's. It is useful to study rift structure and co-explore for oil, gas, coal and uranium resources in Ordos Basin. (authors)

  9. Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

    Lee, S.H.D.; Teats, F.G.; Swift, W.M. (Argonne National Lab., IL (United States)); Banerjee, D.D. (Illinois Clean Coal Inst., Carterville, IL (United States))

    1993-01-01

    Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950[degree]C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

  10. Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

    Lee, S.H.D.; Teats, F.G.; Swift, W.M. [Argonne National Lab., IL (United States); Banerjee, D.D. [Illinois Clean Coal Inst., Carterville, IL (United States)

    1993-04-01

    Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950{degree}C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

  11. Measurements for monitoring ground motion resulting from mining operations in the Rhenish brown coal district; Messungen zur Ueberwachung von bergbaubedingten Bodenbewegungen im rheinischen Braunkohlenbergbau

    Duddek, H; Schaefer, W [Rheinbraun AG, Koeln (Germany)

    1997-12-31

    Coal mining in the Rhenish brown coal district resulted in loose rock slopes with a total height of more than 350 m. Mining operations caused ground motion in open-cast mines, in the slopes and in the region ahead of the face. Internal dumping caused motions of the floors, the overburden tip and te slopes of the open-cast mines. The deformations were measured by different methods, and the evaluations are presented here. As examples, permanent monitoring of a slope using the GEOROBOT measuring system and continuous subsidence measurements in an overburdan dump by means of hydrostatic measuring systems are presented. GEOROBOT ensures quasi-continuous measurements of slope motion with an error of 5-7 mm. Hydrostatic measuring systems on the basis of pressure sensors were developed for measurements of single overburden dump strata and the overburden dump basis during dumping. (orig.) [Deutsch] In den rheinischen Braunkohlentagebauen entstehen Lockergesteinsboeschungen mit Gesamthoehen von mehr als 350 m. Die Gewinnungstaetigkeiten verursachen Entlastungsbewegungen im Tagebau, in den Boeschungen und im Tagebauvorfeld. Die Innenverkippung fuehrt erneut zu Bodenbewegungen im Liegenden, im Kippenkoerper und im Bereich der Tagebauraender. Die auftretenden Deformationen werden mit verschiedenen Messverfahren erfasst, ausgewertet und dargestellt. Beispielhaft werden die permanente Ueberwachung einer Boeschung mittels des automatischen Messsystems GEOROBOT und kontinuierliche Setzungsmessungen in einer Tagebaukippe mit hydrostatischen Messsystemen vorgestellt. Mit GEOROBOT werden quasi kontinuierlich Boeschungsbewegungsmessungen mit einer Genauigkeit von {+-}5 bis 7 mm durchgefuehrt. Auf der Basis von Drucksensoren wurden hydrostatische Messsysteme konzipiert, mit denen Setzungen einzelner Kippscheiben und der Kippenbasis waehrend des Kippenaufbaues ermittelt werden. (orig.)

  12. Measurements for monitoring ground motion resulting from mining operations in the Rhenish brown coal district; Messungen zur Ueberwachung von bergbaubedingten Bodenbewegungen im rheinischen Braunkohlenbergbau

    Duddek, H.; Schaefer, W. [Rheinbraun AG, Koeln (Germany)

    1996-12-31

    Coal mining in the Rhenish brown coal district resulted in loose rock slopes with a total height of more than 350 m. Mining operations caused ground motion in open-cast mines, in the slopes and in the region ahead of the face. Internal dumping caused motions of the floors, the overburden tip and te slopes of the open-cast mines. The deformations were measured by different methods, and the evaluations are presented here. As examples, permanent monitoring of a slope using the GEOROBOT measuring system and continuous subsidence measurements in an overburdan dump by means of hydrostatic measuring systems are presented. GEOROBOT ensures quasi-continuous measurements of slope motion with an error of 5-7 mm. Hydrostatic measuring systems on the basis of pressure sensors were developed for measurements of single overburden dump strata and the overburden dump basis during dumping. (orig.) [Deutsch] In den rheinischen Braunkohlentagebauen entstehen Lockergesteinsboeschungen mit Gesamthoehen von mehr als 350 m. Die Gewinnungstaetigkeiten verursachen Entlastungsbewegungen im Tagebau, in den Boeschungen und im Tagebauvorfeld. Die Innenverkippung fuehrt erneut zu Bodenbewegungen im Liegenden, im Kippenkoerper und im Bereich der Tagebauraender. Die auftretenden Deformationen werden mit verschiedenen Messverfahren erfasst, ausgewertet und dargestellt. Beispielhaft werden die permanente Ueberwachung einer Boeschung mittels des automatischen Messsystems GEOROBOT und kontinuierliche Setzungsmessungen in einer Tagebaukippe mit hydrostatischen Messsystemen vorgestellt. Mit GEOROBOT werden quasi kontinuierlich Boeschungsbewegungsmessungen mit einer Genauigkeit von {+-}5 bis 7 mm durchgefuehrt. Auf der Basis von Drucksensoren wurden hydrostatische Messsysteme konzipiert, mit denen Setzungen einzelner Kippscheiben und der Kippenbasis waehrend des Kippenaufbaues ermittelt werden. (orig.)

  13. Adjustments of microwave-based measurements on coal moisture using natural radioactivity techniques

    Prieto-Fernandez, I.; Luengo-Garcia, J.C.; Alonso-Hidalgo, M.; Folgueras-Diaz, B. [University of Oviedo, Gijon (Spain)

    2006-01-07

    The use of nonconventional on-line measurements of moisture and ash content in coal is presented. The background research is briefly reviewed. The possibilities of adjusting microwave-based moisture measurements using natural radioactive techniques, and vice versa, are proposed. The results obtained from the simultaneous analysis of moisture and ash content as well as the correlation improvements are shown.

  14. Portable rapid gas content measurement - an opportunity for a step change in the coal industry?

    Beamish, Basil; Kizil, Mehmet; Gu, Ming

    2013-01-01

    The last major advance in gas content measurement for coal seams was the introduction of the quick crush technique in the early 1990s. This is a laboratory test method that has proven very reliable over the years. Recent laboratory testing using a portable quick crushing device, known as the portable gas content analyser, has produced consistent gas content results for a set of core samples obtained from a single borehole that intersected four coal seams. The retained gas content values obtained for the seams show the same increasing gas content pattern and gas composition change with depth as the standard quick crush technique. Use of the portable gas content analyser provides the opportunity to produce rapid, reliable gas content measurement of coal that could be developed for assessing gas compliance cores and outburst-prone conditions at a mine site.

  15. CFD Simulation of Temperature Variation in Carboniferous Rock Strata During UCG

    Tomasz Janoszek

    2013-01-01

    Full Text Available The numerical simulation was based on the computational fluid dynamics formalism in order to identify the change of temperature in rock strata during underground coal gasification (UCG. The calculations simulated the coal gasification process using oxygen and water vapour as a gasification agent in 120 hours. Based on the selected software (Ansys-Fluent a model of underground coal gasification (UCG process was developed. The flow of the gasification agent, the description of the turbulence model, the heat-exchange model and the method of simulation of chemical reactions of gasification are presented herein.

  16. Inferring Shallow Subsurface Density Structure from Surface and Underground Gravity Measurements: Calibrating Models for Relatively Undeformed Volcanic Strata at the Jemez Volcanic Field, New Mexico, USA

    Roy, Mousumi; Lewis, Megan; Johnson, Alex; George, Nicolas; Rowe, Charlotte; Guardincerri, Elena

    2018-03-01

    Imaging shallow subsurface density structure is an important goal in a variety of applications, from hydrogeology to seismic and volcanic hazard assessment. We assess the effectiveness of surface and subsurface gravity measurements in estimating the density structure of a well-characterized rock volume: the mesa (a small, flat-topped plateau) upon which the town of Los Alamos, New Mexico, USA is located. Our gravity measurements were made on the mesa surface above a horizontal tunnel and underground, within the tunnel. We demonstrate that, in the absence of other geophysical data such as seismic data or muon attenuation, subsurface (tunnel) gravity measurements are critical to accurately recovering geologic structure. Without the tunnel data, our resolution is limited to roughly the surface gravity station spacing, but by including the tunnel data we can resolve structure to a depth of 10 times the surface gravity station spacing. Densities were obtained using both forward modeling and a Bayesian inverse modeling approach, incorporating relevant constraints from geologic observations. We find that Bayesian inversion, with geologically relevant prior, is a superior approach to the forward models in terms of both robustness and efficiency and correctly predicts the orientation and elevation of important geologic features.

  17. Four-gear strata tiltmeter. Evaluation of resolution capacity

    Balhar, M.

    1984-01-01

    Provides condensed technical characteristics of a four-gear NPS-1 tiltmeter with high resolution. Unit is necessary to determine azimuths and drop angles of strata. Also provides a summarized substantiation of the focusing micro-unit of the tiltmeter. Based on measurements carried out on a turntable and a model borehole, potential errors in determining stratification features were established.

  18. Health and Safety Assessment in Lakhra Coal Mines and Its Mitigation Measures

    Sallahuddin Panhwar

    2017-04-01

    Full Text Available The coal mine excavation, transportation and coal cutting process are involved in hazards and risks that can result in fatalities, injuries and diseases, if these are not properly managed. This study has been undertaken for assessment of the safety and health issues amongst the mines workers. Convenience sampling technique was exercised upon 97 mine workers and interviewed with the help of set questionnaire. Personnel protection to workplace environment was monitored by using physical observation and scientific analysis. All parameters were measured against national and international protocols pertaining to labor law at coal mines. It has been determined that very high risk was persisting while mine excavation, coal cutting and transportation processes. Previous record of last five years was suggesting that 04 deaths happened due to roof fall, 03 fatalities occurred through suffocation by inhaling toxic gases, one causality happened via rope haulage pulley, and also one death due to stone fall down from mine shaft. 121 workers injured in different kinds of accidents within five years. It has been learnt from in-depth analysis that maximum of health risk and subsequent health damages are triggering due to lack of awareness, non-compliance of labor as well as mines laws. Thus, it is recommended that government should not allow coal mining contractors and companies, those which are failing in compliance with the suggested standards.

  19. Comparative discussion on some measurements of the atmospheric natural radioactivity and pollution with coal smoke particles

    Zoran, M.

    1977-01-01

    The results of measuring the natural radioactivity and coal smoke pollution are discussed for two sites in an industrial town, as well as for two heights at the same site, in connection with large scale and local atmospheric stability. The effects of the radiation fog upon the radon daughters acumulation near the ground are examined in some detail. By comparing the pollutant diurnal variations during two periods of similar atmospheric stability in autumn, respectively in winter, the contribution from the dwelling coal heating has been estimated to be about half of the total pollution in the town. (author)

  20. The forecasting method of rock-burst and the application based on overlying multi-strata spatial structure theory

    Cun-Wen Wang; Fu-Xing Jiang; Qing-Guo Sun; Chun-Jiang Sun; Ming Zhang; Zhen-Wen Ji; Xiu-Feng Zhang [University of Science and Technology, Beijing, Beijing (China). Civil & Environmental Engineering School

    2009-02-15

    Based on the overlying multi-strata spatial structure theory and mechanical analysis, the paper discusses the relationship between 'S' shape spatial strata structure movement and mining stress distribution. Coal out-burst forecasting based on 'S' shape spatial strata structure movement was studied. Microseismic monitoring in Huafeng Coal Mine in Shandong Province showed that coal out-burst will ocur when the advancing distance of the longwall face is equal to one, two or three times the length of the longwall face respectively. During these periods, the mined areas approach to square shape while the 'S' shape spatial strata structure acts strongly. Based on this, the time and position of coal out-burst in No. 1410 longwall face of Huafeng Coal Mine was predicted. By using large diameter and deep drill holes in the coal seam and deep drill holes with blasting in the roof at those danger areas, the No. 1410 longwall face safely advanced through those danger areas. During those periods the microseismic monitoring system detected very strong mine quakes. 15 refs., 1 fig., 2 tabs.

  1. Co-firing straw and coal in a 150-MWe utility boiler: in situ measurements

    Hansen, P. F.B.; Andersen, Karin Hedebo; Wieck-Hansen, K.

    1998-01-01

    A 2-year demonstration program is carried out by the Danish utility I/S Midtkraft at a 150-MWe PF-boiler unit reconstructed for co-firing straw and coal. As a part of the demonstration program, a comprehensive in situ measurement campaign was conducted during the spring of 1996 in collaboration...... with the Technical University of Denmark. Six sample positions have been established between the upper part of the furnace and the economizer. The campaign included in situ sampling of deposits on water/air-cooled probes, sampling of fly ash, flue gas and gas phase alkali metal compounds, and aerosols as well...... deposition propensities and high temperature corrosion during co-combustion of straw and coal in PF-boilers. Danish full scale results from co-firing straw and coal, the test facility and test program, and the potential theoretical support from the Technical University of Denmark are presented in this paper...

  2. Sulfur content measurement in coal by X-ray fluorescence method

    Cechak, T.; Thinova, L.

    2001-01-01

    X-ray fluorescence, using backscattering, was employed in the determination of sulfur content and ash content measurement in coal. The results of the methods are given to illustrate the differences between the chemical analysis and X-ray fluorescence method.

  3. A Coal Burst Mitigation Strategy for Tailgate during Deep Mining of Inclined Longwall Top Coal Caving Panels at Huafeng Coal Mine

    Guorui Feng

    2018-01-01

    Full Text Available A coal burst mitigation strategy for tailgate in mining of deep inclined longwall panels with top coal caving at Huafeng Coal Mine is presented in this paper. Field data showed that coal bursts, rib sloughing or slabbing, large convergence, and so forth frequently occurred within the tailgate entries during development and panel retreating employing standard longwall top coal caving (LTCC layout which resulted in fatal injuries and tremendous profit loss. The contributing factors leading to coal bursts were analyzed. Laboratory tests, in situ measurement, and field observation demonstrate that the intrinsic bursting proneness of the coal seam and immediate roof stratum, deep cover, overlying ultrathick (500–800 m conglomerate strata, faults, and, most importantly, improper panel layout led to coal bursts. By employing a new strategy, that is, longwall mining with split-level gateroads (LMSG, gateroads on either end of a LMSG panel are located at different levels within a coal seam, adjacent LMSG panels overlap end to end, and the tailgate of the adjacent new LMSG panel can be located below the headgate entry of the previous LMSG panel or may be offset horizontally with respect to it. Numerical modeling was carried out to investigate the stress distribution and yield zone development within surrounding rock mass which was validated by field investigation. The results indicate that standard LTCC system gave rise to high ground pressure around tailgate entries next to the gob, while LMSG tailgate entry below the gob edge was in a destressed environment. Therefore, coal bursts are significantly mitigated. Field practice of LMSG at Huafeng Coal Mine demonstrates how the new strategy effectively dealt with coal burst problems in mining of deep inclined longwall panels with a reduced incidence of ground control problems. The new strategy can potentially be applied in similar settings.

  4. Apparatus and method for direct measurement of coal ash sintering and fusion properties at elevated temperatures and pressures

    Khan, M. Rashid

    1990-01-01

    A high-pressure microdilatometer is provided for measuring the sintering and fusion properties of various coal ashes under the influence of elevated pressures and temperatures in various atmospheres. Electrical resistivity measurements across a sample of coal ash provide a measurement of the onset of the sintering and fusion of the ash particulates while the contraction of the sample during sintering is measured with a linear variable displacement transducer for detecting the initiation of sintering. These measurements of sintering in coal ash at different pressures provide a mechanism by which deleterious problems due to the sintering and fusion of ash in various combustion systems can be minimized or obviated.

  5. Upper Paleozoic coal measures and unconventional natural gas systems of the Ordos Basin, China

    Xuan Tang

    2012-11-01

    Full Text Available Upper Paleozoic coal measures in the Ordos Basin consist of dark mudstone and coal beds and are important source rocks for gas generation. Gas accumulations include coal-bed methane (CBM, tight gas and conventional gas in different structural areas. CBM accumulations are mainly distributed in the marginal area of the Ordos Basin, and are estimated at 3.5 × 1012 m3. Tight gas accumulations exist in the middle part of the Yishan Slope area, previously regarded as the basin-centered gas system and now considered as stratigraphic lithologic gas reservoirs. This paper reviews the characteristics of tight gas accumulations: poor physical properties (porosity < 8%, permeability < 0.85 × 10−3 μm2, abnormal pressure and the absence of well-defined gas water contacts. CBM is a self-generation and self-reservoir, while gas derived from coal measures migrates only for a short distance to accumulate in a tight reservoir and is termed near-generation and near-reservoir. Both CBM and tight gas systems require source rocks with a strong gas generation ability that extends together over wide area. However, the producing area of the two systems may be significantly different.

  6. Survey report for fiscal 1999 on advanced exploitation of coal overseas. Survey of coal exploitation enhancement overseas (Coal industry's measures for persistent low coal price); 1999 nendo kaigaitan kaihatsu kodoka nado chosa. Kaigaitan kaihatsu sokushin chosa (sekitan kakaku teimeika ni okeru sekitan sangyo no taiosaku)

    NONE

    2000-03-01

    Surveys were conducted of the trends of coal companies in the U.S. and Australia and of the lookout for new coal field development in Australia for the purpose of contributing to the stable supply of coal in the future. In the U.S., the coal industry has experienced serious changes in these ten years, and various corporations, such as Peabody, Arch Coal, CONSOL, and Kennecott have come to resort to drastic measures for their survival. In Australia, coal price is lower and contract terms are shorter with less demand for coal supply thanks to the economic crisis in Asia. As for demand for coal in Asia, on the other hand, it is deemed that in 2010 there will be a 41% increase over the 1995 level and that, therefore, coal field preservation and new field exploitation are necessary. Since production by strip mining in New South Wales State is to decrease in 2012 and after, it is expected that new projects will start only after 2012. Comprehensive development projects are going to be launched in the areas surrounding the Surat district, Queensland State, and therefore new projects will be easier to start in this region. Since the Surat coal is to be collected after a little stripping, it is expected that it will be able to compete with the Indonesian coal. (NEDO)

  7. Model for the prediction of subsurface strata movement due to underground mining

    Cheng, Jianwei; Liu, Fangyuan; Li, Siyuan

    2017-12-01

    The problem of ground control stability due to large underground mining operations is often associated with large movements and deformations of strata. It is a complicated problem, and can induce severe safety or environmental hazards either at the surface or in strata. Hence, knowing the subsurface strata movement characteristics, and making any subsidence predictions in advance, are desirable for mining engineers to estimate any damage likely to affect the ground surface or subsurface strata. Based on previous research findings, this paper broadly applies a surface subsidence prediction model based on the influence function method to subsurface strata, in order to predict subsurface stratum movement. A step-wise prediction model is proposed, to investigate the movement of underground strata. The model involves a dynamic iteration calculation process to derive the movements and deformations for each stratum layer; modifications to the influence method function are also made for more precise calculations. The critical subsidence parameters, incorporating stratum mechanical properties and the spatial relationship of interest at the mining level, are thoroughly considered, with the purpose of improving the reliability of input parameters. Such research efforts can be very helpful to mining engineers’ understanding of the moving behavior of all strata over underground excavations, and assist in making any damage mitigation plan. In order to check the reliability of the model, two methods are carried out and cross-validation applied. One is to use a borehole TV monitor recording to identify the progress of subsurface stratum bedding and caving in a coal mine, the other is to conduct physical modelling of the subsidence in underground strata. The results of these two methods are used to compare with theoretical results calculated by the proposed mathematical model. The testing results agree well with each other, and the acceptable accuracy and reliability of the

  8. Coal rank (vitrinite reflectance) data for Cretaceous/Tertiary coal measures in the Grande Cache and Hinton areas, Alberta

    Kalkreuth, W.D.; Langenberg, W.; McMechan, M.E.; Tomica, M.A.; McDougall, W.; Burchard, K.

    1996-07-01

    A total of 544 vitrinite reflectance values are reported. The outcrop locations and other pertinent data are listed. Vitrinite reflectances determined in subsurface samples from two coal exploration boreholes and 13 petroleum exploration wells are tabulated. The data have been used (in other studies) to evaluate maturation levels in potential source rocks and to assess methane potential of the coal deposits. A diskette containing the data is included. 18 refs., 1 fig., 2 tabs.

  9. Geological structure of strata and the occurence of gas outbursts

    Koewing, K

    1977-10-20

    Geological conditions which may have an influence on gas outbursts are depth, rank, type of formation, tectonic stresses, and the petrological form of the neighboring rock. The risk of outbursts is greater if there are dirt bands in the seam, since the coal can slide on these. Tectonically disturbed zones in seams containing more than 9 cu m of gas per ton are especially dangerous. Tectonic stress is not necessarily an indication of the severity of outbursts. Gas and sandstone outbursts do not depend on tectonic disturbance; outburst-prone sandstones have a greater pore volume and lower strength than normal. Almost all outbursts from the floor occur where the strata immediately below are impervious to gas and sandstone is present lower down. (In German)

  10. Apparatus and process for continuous measurement of moisture in moving coal by neutron thermalization

    Stewart, R.F.

    1967-01-01

    The invention relates to an apparatus and process for the measurement of moisture contents in solid materials. More particularly, the invention makes available a continuous moisture analysis of a moving mass of material, such as coal, by penetrating such material with neutrons emitted from a source of fast neutrons and detecting, counting, and recording slowed or thermalized neutrons reflected from the internal structure of the material. (U.S.)

  11. Possibility of convergence measurement of gates in coal mining using terrestrial 3D laser scanner

    Kukutsch, Radovan; Kajzar, Vlastimil; Koníček, Petr; Ptáček, Jiří; Waclawik, Petr

    2015-01-01

    Roč. 14, č. 1 (2015), s. 1-8 ISSN 2300-3960 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : 3D laser scanning * point clouds * mining * geotechnical monitoring * convergence measurement Subject RIV: DH - Mining, incl. Coal Mining http://www.sciencedirect.com/science/article/pii/S2300396015000063

  12. Measurements and simulation for design optimization for low NOx coal-firing system

    E. Bar-Ziv; Y. Yasur; B. Chudnovsky; L. Levin; A. Talanker [Ben-Gurion University of Negev, Beer-Sheva (Israel)

    2003-07-01

    The information required to design a utility steam generator is the heat balance, fuel analysis and emission. These establish the furnace wall configuration, the heat release rates, and the firing technology. The furnace must be sized for (1) residence time for complete combustion with low NOx, and (2) reduction of flue gas temperature to minimize ash deposition. To meet these, computational fluid dynamics (CFD) of the combustion process in the furnace were performed and proven to be a powerful tool for this purpose. Still, reliable numerical simulations require careful interpretation and comparison with measurements. We report numerical results and measurements for a 575 MW pulverized coal tangential firing boiler of the Hadera power plant of Israel Electric Corporation (IEC). Measured and calculated values were found to be in reasonable agreement. We used the simulations for optimization and investigated temperature distribution, heat fluxes and concentration of chemical species. We optimized both the furnace flue gas temperature entering the convective path and the staged residence time for low NOx. We tested mass flow rates through close-coupled and separate overfire air ports and its arrangement and the coal powder fineness. These parameters can control the mixing rate between the fuel and the oxidizer streams and can affect the most important characteristics of the boiler such as temperature regimes, coal burning rate and nitrogen oxidation/reduction. From this effort, IEC started to improve the boiler performance by replacing the existing typical tangential burners to low NOx firing system to ensure the current regulation requirements of emission pollutions.

  13. Sedimentology and sequence stratigraphy of the Lopingian (Late Permian) coal measures in southwestern China

    Wang, Hao [School of Geosciences and Surveying Engineering, China University of Mining and Technology, Beijing (China); School of Earth and Environment, University of Leeds (United Kingdom); Shao, Longyi; Hao, Liming; Zhang, Pengfei [School of Geosciences and Surveying Engineering, China University of Mining and Technology, Beijing (China); Glasspool, Ian J. [Department of Geology, Field Museum of Natural History, Chicago, Illinois (United States); Wheeley, James R.; Hilton, Jason [School of Geography, Earth and Environmental Sciences, University of Birmingham (United Kingdom); Wignall, Paul B. [School of Earth and Environment, University of Leeds (United Kingdom); Yi, Tongsheng [Guizhou Bureau of Coal Geological Exploration, Guiyang, Guizhou (China); Zhang, Mingquan [Coal Geology and Prospecting Institute of Yunnan Province, Kunming, Yunnan (China)

    2011-01-01

    The Lopingian coal measures of southwestern China were deposited within a range of facies associations spanning a spectrum of settings from fluvial to marine carbonate platform. The transitional to terrestrial coal measures are dominated by siliciclastics, but they also contain fifteen laterally extensive marine bands (limestone beds and mudstone). These bands act as marker horizons that enable correlation between fully marine and terrestrial facies. Examination of this range of facies and their sedimentology has enabled the development of a high-resolution sequence stratigraphic framework. Set against the established backdrop of second-order Lopingian transgression, sixteen fourth-order sequences and three composite sequences (third-order) are recognized. Results show that, in the composite sequences, peat accumulation in the seaward parts of the study area predominantly correlates with early transgressive sequence sets (TSS), while in more landward areas it correlates with the middle TSS to late highstand sequence sets (HSS). Differences in peat-accumulation regimes within the sequence stratigraphic framework are attributed to variations in subsidence and background siliciclastic input rates in different depositional settings, with these combining to produce differences in the rate of accommodation change. The preservation of coal resources in the middle to late HSS in this area was most likely related to the rise of the regional base level throughout the Lopingian. (author)

  14. Mechanism and Prevention of a Chock Support Failure in the Longwall Top-Coal Caving Faces: A Case Study in Datong Coalfield, China

    Zhu Li

    2018-01-01

    Full Text Available Longwall chock support failures seriously restrain the safety and high-efficiency of mining of extra thick coal seams, as well as causing a great waste of coal resources. During longwall top-coal caving (LTCC, the influential effect of the properties and the movement regulation of top-coal on strata behavior cannot be ignored, since the top-coal is the medium through which the load of the overlying strata is transferred to the chock supports. Taking Datong coalfield as an example, the mechanism of a chock support failure in the LTCC face was investigated. Research findings indicated that the hard top-coal and insufficient chock support capacity were primary reasons for chock support failure accidents. On account of the field-measured results, a new method to determine support capacity was proposed, which fully took the impact of the top-coal strength into consideration. The calculation revealed that the required support capacity had exceeded the existing production maximum, at about 22,000 KN. Since it was unrealistic to simply increase chock support capacity, other approaches, according to the theoretical analysis, were proposed, such as lowering the integrity and strength of the top-coal, and upgrading its crushing effect to weaken the support load effectively during the weighting period, which reduces the likelihood of chock support accidents occurring. Based on this, hydraulic fracturing for hard top-coal and optimization of the caving process (chock supports raised up and down repeatedly by manual operation before moving forward were presented. The proposed solutions were successfully applied in LTCC-west8101 for subsequent mining and achieved substantial benefits. The above research provides valuable references and ideas for the control of strata behavior to ensure safe and highly efficient mining in extremely thick and hard coal seams with the LTCC method.

  15. Field measurement of mixing degree in coal mixer by later activable tracer method

    Yokooji, Makoto; Uemura, Katsumi; Adachi, Syoichi

    1975-01-01

    Mixing effectiveness in a rotary drum mixer for coke production was examined. Though the method to use the dispersion of characteristic values such as ash content or volatile components is common for measuring the mixing effectiveness, here the later activable tracer method with radioisotopes was employed, because the former method includes the dispersion of the characteristic values for raw materials themselves, and is poor in detectability. In a preliminary test, the expression for mixing degree was determined, and the tracer nuclide was selected. Coal mixture was irradiated in the TRIGA II reactor of St. Paul University for 4 hours at 100 kW. then further preliminary test was performed for La and Mn which were selected among the typical usable elements listed up by reviewing their γ-spectra. Finally, Mn was adopted by comparing both elements regarding their time required for activation analysis and economy. Manganese concentration originally contained in the coal mixture was 38 ppm. Mixing degree after passing through the coal mixer was 99.8%. The results of the regular test are shown in a table, and indicate that the mixer fully attained its aim. (Wakatsuki, Y.)

  16. FY 2000 Feasibility study on the environmentally-friendly coal utilization systems as part of the international project for coal utilization measures. Feasibility study on supporting introduction of the environmentally-friendly coal utilization systems in Vietnam (Model project for introduction of advanced coal preparation systems); 2000 nendo kokusai sekitan riyo taisaku jigyo chosa hokokusho. Kankyo chowagata sekitan riyo system kanosei chosa jigyo Vietnam ni okeru kankyo chowagata sekitan riyo system donyu shien jigyo (kodo sentan system donyu model jigyo kanosei chosa jigyo)

    NONE

    2001-06-01

    The feasibility study was conducted on a model project in Vietnam, aimed at solving the environmental pollution problems resulting from use of coal by demonstrating and disseminating the Japan's environmental technologies in the Southeast Asian countries. The feasibility study was conducted for the Cua Ong Coal Preparation Enterprise, which has the largest coal preparation capacity in Vietnam and port facilities. It is treating raw coal from 10 coal mines for classification and preparation, and shipping coal of various types that meet the standards for domestic use and export. The survey results point out that unrecovered coal remains in waste water discharged from the coal preparation plants to pollute the sea area, and that quantity of the refuse increases because of the unrecovered coal it contains. The environmental technologies needed to introduce include modification to variable wave pattern type jigging separator, refuse height measuring instrument and automatic controller, circulating heavy medium gravimeter, highly functional settling pond, and flocculent facilities. (NEDO)

  17. Determination of ash content of coal by mass absorption coefficient measurements at two X-ray energies

    Fookes, R.A.; Gravitis, V.L.; Watt, J.S.

    1977-01-01

    A method for determining the ash content of coal is proposed. It involves measurements proportional to mass absorption coefficients of coal at two X-ray energies. These measurements can be made using X-ray transmission or scatter techniques. Calculations based on transmission of narrow beams of X-rays have shown that ash can be determined to about 1wt%(1 sigma) in coal of widely varying ash content and composition. Experimentally, ash content was determined to 0.67wt% by transmission techniques and 1.0wt% by backscatter techniques in coal samples from the Bulli seam, NSW, Australia, having ash in the range 11-34wt%. For samples with a much wider range of coal composition (7-53wt% ash and 0-25wt% iron in the ash), ash content was determined by backscatter measurements to 1.62wt%. The method produced ash determinations at least as accurate as those produced by the established technique which compensates for variation in iron content of the ash by X-ray fluorescence analysis for iron. Compared with the established technique, it has the advantage of averaging analysis over much larger volumes of coal, but the disadvantage that much more precise measurements of X-ray intensities are required. (author)

  18. Environmental policy in brown coal mining in accordance with the precautionary measures principle and polluter pays principle

    Hamann, R.; Wacker, H.

    1993-01-01

    The precautionary measures principle and the polluter pays principle in brown coal mining are discussed. Ground water subsidence and landscape destruction are local or regional problems and thus easily detectable. If damage cannot be avoided, its authors are known and will pay. In spite of all this, the German brown coal industry is well able to compete on the world market with others who don't care about the environmental damage they may cause. (orig./HS)) [de

  19. Permeability Prediction in Deep Coal Seam: A Case Study on the No. 3 Coal Seam of the Southern Qinshui Basin in China

    2013-01-01

    The coal permeability is an important parameter in mine methane control and coal bed methane (CBM) exploitation, which determines the practicability of methane extraction. Permeability prediction in deep coal seam plays a significant role in evaluating the practicability of CBM exploitation. The coal permeability depends on the coal fractures controlled by strata stress, gas pressure, and strata temperature which change with depth. The effect of the strata stress, gas pressure, and strata temperature on the coal (the coal matrix and fracture) under triaxial stress and strain conditions was studied. Then we got the change of coal porosity with strata stress, gas pressure, and strata temperature and established a coal permeability model under tri-axial stress and strain conditions. The permeability of the No. 3 coal seam of the Southern Qinshui Basin in China was predicted, which is consistent with that tested in the field. The effect of the sorption swelling on porosity (permeability) firstly increases rapidly and then slowly with the increase of depth. However, the effect of thermal expansion and effective stress compression on porosity (permeability) increases linearly with the increase of depth. The most effective way to improve the permeability in exploiting CBM or extracting methane is to reduce the effective stress. PMID:24396293

  20. The Late Paleozoic relative gas fields of coal measure in China and their significances on the natural gas industry

    Chenchen Fang

    2016-12-01

    Full Text Available The coal measure gas sources of coal-derived gas fields in the Late Paleozoic China are the Lower Carboniferous Dishuiquan Formation, the Upper Carboniferous Batamayineishan Formation and Benxi Formation, the Lower Permian Taiyuan Formation and Shanxi Formation, and the Upper Permian Longtan Formation. The coal-derived gas accumulates in Ordovician, Carboniferous, Permian, and Paleocene reservoirs and are distributed in Ordos Basin, Bohai Bay Basin, Junggar Basin, and Sichuan Basin. There are 16 gas fields and 12 of them are large gas fields such as the Sulige large gas field which is China's largest reserve with the highest annual output. According to component and alkane carbon isotope data of 99 gas samples, they are distinguished to be coal-derived gas from coal-derived gas with δ13C2 > −28.5‰ and δ13C1 -δ13C2 -δ13C3 identification chart. The Late Paleozoic relative gas fields of coal measure are significant for the Chinese natural gas industry: proven natural gas geological reserves and annual output of them account for 1/3 in China, and the gas source of three significant large gas fields is coal-derived, which of five significant large gas fields supporting China to be a great gas producing country. The average reserves of the gas fields and the large gas fields formed from the late Paleozoic coal measure are 5.3 and 1.7 times that of the gas fields and the large gas fields in China.

  1. Performance analysis of US coal-fired power plants by measuring three DEA efficiencies

    Sueyoshi, Toshiyuki; Goto, Mika; Ueno, Takahiro

    2010-01-01

    Data Envelopment Analysis (DEA) has been widely used for performance evaluation of many organizations in private and public sectors. This study proposes a new DEA approach to evaluate the operational, environmental and both-unified performance of coal-fired power plants that are currently operating under the US Clean Air Act (CAA). The economic activities of power plants examined by this study are characterized by four inputs, a desirable (good) output and three undesirable (bad) outputs. This study uses Range-Adjusted Measure (RAM) because it can easily incorporate both desirable and undesirable outputs in the unified analytical structure. The output unification proposed in this study has been never investigated in the previous DEA studies even though such a unified measure is essential in guiding policy makers and corporate leaders. Using the proposed DEA approach, this study finds three important policy implications. First, the CAA has been increasingly effective on their environmental protection. The increased environmental performance leads to the enhancement of the unified efficiency. Second, the market liberalization/deregulation was an important business trend in the electric power industry. Such a business trend was legally prepared by US Energy Policy Act (EPAct). According to the level of the market liberalization, the United States is classified into regulated and deregulated states. This study finds that the operational and unified performance of coal-fired power plants in the regulated states outperforms those of the deregulated states because the investment on coal-fired power plants in the regulated states can be utilized as a financial tool under the rate-of-return criterion of regulation. The power plants in the deregulated states do not have such a regulation premium. Finally, plant managers need to balance between their environmental performance and operational efficiency.

  2. Measurement of O2 in the Combustion Chamber of Apulverized Coal Boiler

    Břetislav Janeba

    2012-01-01

    Full Text Available Operational measurements of the O2 concentration in the combustion chamber of a pulverized coal boiler are not yet common practice. Operators are generally satisfied with measuring the O2 concentration in the second pass of the boiler, usually behind the economizer, where a flue gas sample is extracted for analysis in a classical analyzer. A disadvantage of this approach is that there is a very weak relation between the measured value and the condition in specific locations in the fireplace, e.g. the function of the individual burners and the combustion process as a whole. A new extractionline was developed for measuring the O2 concentration in the combustion chamber. A planar lambda probe is used in this approach. The extraction line is designed to get outputs that can be used directly for diagnosis or management of the combustion in the boiler.

  3. Coal background paper. Coal demand

    1997-01-01

    Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

  4. Trace elemental composition of Nigerian coal measured by neutron activation analysis

    Ndiokwere, Ch.L.; Guinn, V.P.; Burtner, D.

    1983-01-01

    The instrumental neutron activation analysis (INAA) technique has been used to determine 17 major, minor and trace elements in samples of the three major sources of Nigerian coal. The NBS Standard Reference Material, Coal SRM 1632, was also analyzed, for the purpose of verifying the accuracy of the method. The concentrations of the major elements determined for the Nigerian coal were found to be much lower than the mean values of those reported for coal samples from other parts of the world. (author)

  5. LTRM Fish Sampling Strata, UMRS La Grange Reach

    Department of the Interior — The data set includes delineation of sampling strata for the six study reaches of the UMRR Program’s LTRM element. Separate strata coverages exist for each of the...

  6. LTRM Water Quality Sampling Strata, UMRS La Grange Reach

    Department of the Interior — The data set includes delineation of sampling strata for the six study reaches of the UMRR Program’s LTRM element. Separate strata coverages exist for each of the...

  7. Measurement of slurry droplets in coal-fired flue gas after WFGD.

    Wu, Xue-Cheng; Zhao, Hua-Feng; Zhang, Yong-Xin; Zheng, Cheng-Hang; Gao, Xiang

    2015-10-01

    China owns the world's largest capacity of coal-fired power units. By the end of 2012, the capacity of installed national thermal power has been 819.68 million kilowatts. The latest standard requires that newly built power plants emit SO2 in no more than 100 mg/m(3) and the emission of old ones be lower than 200 mg/m(3) while in some key areas the emission should be controlled under 50 mg/m(3). So by the end of 2012, 90% of the active coal-fired units have been equipped with flue gas desulfurization devices. Among the desulfurization methods adopted, limestone-gypsum wet flue gas desulphurization accounts for 92%, causing the problem of fine droplets in the exhaust gas after defogger, which may even form "gypsum rain." At present, sampling methods are widely used at home and abroad, such as magnesium ion tracer method, modified magnesium ion tracer method and chemical analysis. In addition, some scholars use aerodynamic methods, such as ELPI, to measure the diameter distribution and concentration. The methods mentioned above all have their own demerits, such as the inability to on-line, continuous measurements and the need of prolonged measuring time. Thus, in this paper some potential optical on-line methods are presented, such as Fraunhofer diffraction pattern analysis and wavelength-multiplexed laser extinction. Also brought up are their measuring scope and merits. These methods have already been utilized to measure small liquid droplets and their demonstrations and evaluations are as well stated. Finally, a 3D imaging method based on digital holographic microscope is proposed for in-line measurement of size and concentration of slurry droplets. The feasibility of this method is demonstrated by preliminary experimental investigation.

  8. Undergraduates Discovering Folds in ''Flat'' Strata: An Unusual Undergraduate Geology Field Methods Course

    Abolins, Mark

    2014-01-01

    Undergraduates learned to measure, map, and interpret bedding plane attitudes during a semesterlong geology field methods course in a field area where strata dip less than 98. Despite the low dip of the strata, 2011 field course students discovered a half-kilometer-wide structural basin by using digital levels and Brunton pocket transits to…

  9. Long-term measurements with a mercury monitor in a hard coal power plant; Langzeitmessungen mit einem Quecksilbermonitor im Steinkohlekraftwerk

    Korell, Jens; Paur, Hanns R.; Seifert, Helmut [Forschungszentrum Karlsruhe GmbH, Karlsruhe (DE). Inst. fuer Technische Chemie, Bereich Thermische Abfallbehandlung (ITC-TAB)

    2008-07-01

    The emission limits of coal-fired power stations with a furnace thermal performance of more than 50 MW are regulated in the 13th Ordinance for the Implementation of the Federal Immission Control Act. The amended version of this regulation contains a limit value of 30 {mu}g/m{sup 3}. In order to examine the compliance of these limits particular in the case of substitute fuels by long-term measurements, suitable continuous measurement devices must be available. Under this aspect, the authors of the contribution under consideration report on a mercury monitor in the hard coal power station. Hg-CEM measurements are accomplished with concentrations up to 800 mg/m{sup 3} sulphure dioxide. The experimental concentrations of mercury in the raw gas correlate with the computed concentration. In a coal-fired power station, a failure-free operation of the Hg-CEM to the flue gas desulphurisation plant could be realized over four months.

  10. An investigation on groundwater recovery rate within sub sea floor tunnels at closed coal mines

    Nakata, Eiji; Suenaga, Hiroshi; Oyama, Takahiro; Nomura, Tokisada; Ichihara, Yoshihisa

    2008-01-01

    The groundwater recovery rate investigated at the closed coal mines extended within sub sea floor tunnels. The Ikeshima and the Taiheiyo coal mine companies exploited the deep coal-bearing strata beneath the ocean. Ikeshima coal mine, excavated S.L. -650m to 6km offshore from Ikeshima island, was closed at November 2002, and Taiheiyo coal mine, excavated S.L. -720m to 9km offshore from Hokkaido, was stopped to excavate from the deep area at January 2003. After closing and stopping of development, we began the investigation of the groundwater recovery rate at both coal mines. The groundwater level of Ikeshima coal mine raised +405m per 1.8 years at the main shaft. The permeability coefficient estimated between 10 - 8 m /s and 10 -6 m/s to use the water recovery rate at the shaft. Otherwise, at Taiheiyo coal mine, we measured the air pressure in tubes used by 3.5km 2.5km, and 1.5km length 2mm diameters tubes to estimate the groundwater recovery level at the 3.2km offshore plug site. Groundwater didn't reach 4.7km (1.5+3.2km) area until November 2004. There were breakdown of shotcleate and rock mass from the roof of tunnel at 5.3km from offshore line. In this paper, we try to show the groundwater recovery rate of these sub sea floor collieries. (author)

  11. Analysing the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau

    Wei Cao

    2017-09-01

    Full Text Available The coal mining has brought a series of ecological problems and environmental problems in permafrost regions. Taking Muli coal-mining area as an example, this article attempts to analyse the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau. This article analyses the influence of open mining on the surrounding permafrost around the open pit by using the numerical simulation. The results show that (1 based on the interrelation between coal mining and permafrost environment, these main environmental harm include the permafrost change and the natural environment change in cold regions; (2 once the surface temperature rises due to open mining, the permafrost will disappear with the increase of exploitation life. If considering the solar radiation, the climate conditions and the geological condition around the pit edge, the maximum thaw depth will be more than 2 m; (3 the protection measures are proposed to avoid the disadvantage impact on the permafrost environment caused by coal mining. It will provide a scientific basis for the resource development and environment protection in cold regions.

  12. Synchronized droplet size measurements for Coal-Water-Slurry (CWS) diesel sprays of an electronically-controlled fuel injection system

    Kihm, K. D.; Terracina, D. P.; Payne, S. E.; Caton, J. A.

    Experiments were completed to study intermittent coal-water slurry (CWS) fuel sprays injected from an electronically-controlled accumulator injector system. A laser diffraction particle analyzing (LDPA) technique was used to measure the spray diameters (Sauter mean diameter, SMD) assuming the Rosin-Rammler two parameter model. In order to ensure an accurate synchronization of the measurement with the intermittent sprays, a new synchronization technique was developed using the light extinction signal as a triggering source for the data taking initiation. This technique allowed measurement of SMD's near the spray tip where the light extinction was low and the data were free from the multiscattering bias. Coal-water slurry fuel with 50% coal loading in mass containing 5 (mu)m mass median diameter coal particulates was considered. Injection pressures ranging from 28 to 110 MPa, two different nozzle orifice diameters, 0.2 ad 0.4 mm, and four axial measurement locations from 60 to 120 mm from the nozzle orifice were studied. Measurements were made for pressurized (2.0 MPa in gauge) and for ambient chamber conditions. The spray SMD showed an increase with the distance of the axial measurement location and with the ambient gas density, and showed a decrease with increasing injection pressure. A correlation of the Sauter mean diameter with the injection conditions was determined. The results were also compared with previous SMD correlations that were available only for diesel fuel sprays.

  13. Method and apparatus for measuring incombustible content of coal mine dust using gamma-ray backscatter

    Armstrong, F.E.

    1976-01-01

    A method and apparatus for measuring incombustible content of particulate material, particularly coal mine dust, include placing a sample of the particulate material in a container to define a pair of angularly oriented surfaces of the sample, directing an incident gamma-ray beam from a radiation source at one surface of the sample and detecting gamma-ray backscatter from the other surface of the sample with a radiation detector having an output operating a display to indicate incombustible content of the sample. The positioning of the source and detector along different surfaces of the sample permits the depth of the scattering volume defined by intersection of the incident beam and a detection cone from the detector to be selected such that variations in scattered radiation produced by variations in density of the sample are compensated by variations in the attenuation of the incident beam and the gamma-ray backscatter. 17 claims 5 figures

  14. Revisiting platinum group elements of Late Permian coals from western Guizhou Province, SW China

    Qi, Liang [State Key Lab of Ore Deposit Geochemistry, Institute of Geochemistry, Chinese Academy of Sciences, Guiyang, 550002 (China); Gao, Jianfeng [Department of Earth Sciences, The University of Hong Kong, Pokfulam Road, Hong Kong SAR (China)

    2008-08-05

    Twenty five coal samples from the Late Permian coal-bearing strata in Weining, Nayong, and Zhijin, western Guizhou Province, SW, China, were analyzed for platinum group elements (PGEs). The coal ashes were digested by the Carius tube technique and accurately measured by isotope dilution-inductively coupled plasma mass spectrometry (ID-ICP-MS) for all PGEs. The results are much lower than the previous reported values. Our study suggested that the previously reported PGE values are incorrect and may due to the polyatomic interferences in ICP-MS measurements. In our study, samples from the Weining coalfield have the lowest PGE contents (from 0.019 Ir to 0.42 ng/g Pd), which represent the PGE background value in coal in western Guizhou province. Some of the coals have Pt and Pd contents about 20-times higher than the background value, indicating PGEs are concentrated. We also reported new and reliable PGE data and background value of coal in western Guizhou province, SW, China, and suggested to rework the PGE background values of Chinese coals. (author)

  15. Tribocharging in electrostatic beneficiation of coal: Effects of surface composition on work function as measured by x-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy in air

    Trigwell, S.; Mazumder, M.K.; Pellissier, R.

    2001-01-01

    The cleaning of coal by electrostatic beneficiation is based on tribocharging characteristics of pulverized coal particles with diameter smaller than 120 μm. The tribocharging process should be such that the organic coal particles must charge with a polarity opposite to that of the sulfur and the mineral containing particles so that coal can be separated from minerals by using a charge separator. However, the charge distribution of electrostatically separated coal particles indicates that coal exhibits bipolar charging. A significant fraction of the coal particles charges negatively which appears to be in conflict with expectations in that the organic coal particles should charge positively, and the mineral particles, present as impurities such as pyrite, charge negatively when tribocharged against copper. The relative work functions of the particles (coal and mineral) and that of the metal surface (copper or stainless steel) used for tribocharging predict these expected results. However, ultraviolet photoelectron spectroscopy (UPS) measurements in air on specimens of three different coal species, showed the work function to be approximately 5.4 eV, which is higher than a reported measured work function of 3.93 eV. Studies by UPS and x-ray photoelectron spectroscopy on copper, stainless steel, aluminum, and other commonly used tribocharging materials such as nylon and polytetrafluorethylene, as well as pure pyrite, showed that the work function varied considerably as a function of surface composition. Therefore, the reason for the bipolar charging of the coal particles may be the too small differences in work functions between coal powder and copper used as the charging material. The choice of a material for impaction triboelectric charging for coal or mineral separation should therefore depend upon the actual work function as modified by the ambient conditions such as moisture content and the oxidation of the surface

  16. Measurement of radon activity, exhalation rate and radiation dose in fly ash and coal samples from NTPC, Badarpur, Delhi, India

    Gupta, Mamta; Verma, K.D.; Mahur, A.K.; Prasad, R.; Sonkawade, R.G.

    2013-01-01

    In the present study radon activities and exhalation rates from fly ash and coal samples from NTPC (National Thermal Power Corporation) situated at Badarpur, Delhi, India, have been measured. 'Sealed Can Technique' using LR-115 type II track detectors was employed. In fly ash samples, radon activity has been found to vary from 400.0 ± 34.7 to 483.9 ± 38.1Bqm -3 with an average value of 447.1 ± 36.6 Bqm -3 and in coal samples, radon activity has been found to vary from 504.0 ± 39.0 to 932.1 ± 52.9 Bqm -3 with an average value of 687.2 ± 45.2 Bqm -3 . Radon exhalation rate from coal is found to be higher than radon exhalation rate from its ash products, whereas the opposite is expected. Indoor inhalation exposure (radon) effective dose has also been estimated. (author)

  17. Use of neutron activation analysis to measure the variation in trace element concentrations in a coal seam

    Fardy, J.J.; Swaine, D.J.

    1985-01-01

    Trace element concentrations were measured by neutron activation on 57 run-of-mine coal samples from several locations in seven mines located in the Lithgow seam in the Western Coalfield, Sydney Basin. Results were tabulated as ratios of the highest to the lowest variance for each element

  18. Carbon emission coefficient measurement of the coal-to-power energy chain in China

    Yu, Shiwei; Wei, Yi-Ming; Guo, Haixiang; Ding, Liping

    2014-01-01

    Highlights: • CO 2 emissions coefficient of the coal-energy chain in China is currently at 875 g/kW h −1 . • The emission coefficient is a relatively low level compared with other countries. • CO 2 is the main type of GHG emission and the most direct emission in the chain. • A great decline of potential energy use exists in the coal mining process of China compared with other countries. - Abstract: Coal-fired electricity generation has become the largest source of carbon emission in China. This study utilizes life-cycle assessment to assess the effect of carbon emissions and to calculate the coefficient of carbon emissions in coal-to-energy chains. Results show that the carbon emission coefficient of the coal-to-energy chain in China is 875 g/kW h −1 , which is a relatively low level compared with that of other countries. CO 2 is the main type of greenhouse gas emission and is the most abundant type of direct emission. China has to reduce electrical consumption in the coal-mining process to reduce carbon emissions in coal-to-energy chains. Moreover, China has to facilitate railway-line construction to improve the proportion of railway transportation to coal transportation

  19. Innovative Coal Solids-Flow Monitoring and Measurement Using Phase-Doppler and Mie Scattering Techniques

    Stephen Seong Lee

    2010-01-19

    Fuel flow to individual burners is complicated and difficult to determine on coal fired boilers, since coal solids were transported in a gas suspension that is governed by the complex physics of two-phase flow. The objectives of the project were the measurements of suspended coal solids-flows in the simulated test conditions. Various extractive methods were performed manually and can give only a snapshot result of fuel distribution. In order to measure particle diameter & velocity, laser based phase-Doppler particle analyzer (PDPA) and particle image velocimetry (PIV) were carefully applied. Statistical methods were used to analyze particle characteristics to see which factors have significant effect. The transparent duct model was carefully designed and fabricated for the laser-based-instrumentation of solids-flow monitoring (LISM). The experiments were conducted with two different kinds of particles with four different particle diameters. The particle types were organic particles and saw dust particles with the diameter range of 75-150 micron, 150-250 micron, 250-355 micron and 355-425 micron. The densities of the particles were measured to see how the densities affected the test results. Also the experiment was conducted with humid particles and fog particles. To generate humid particles, the humidifier was used. A pipe was connected to the humidifier to lead the particle flow to the intersection of the laser beam. The test results of the particle diameter indicated that, the mean diameter of humid particles was between 6.1703 microns and 6.6947 microns when the humid particle flow was low. When the humid particle flow was high, the mean diameter was between 6.6728 microns and 7.1872 microns. The test results of the particle mean velocity indicated that the mean velocity was between 1.3394 m/sec and 1.4556 m/sec at low humid particle flow. When the humid particle flow was high, the mean velocity was between 1.5694 m/sec and 1.7856 m/sec. The Air Flow Module, TQ

  20. Field trials of aquifer protection in longwall mining of shallow coal seams in China

    Zhang, D.S.; Fan, G.W.; Liu, Y.D.; Ma, L.Q. [State Key Laboratory of Coal Resource & Mine Safety, Xuzhou (China)

    2010-09-15

    The large-scale mining of shallow coal seams has a significant impact on the overlying aquifers and surface ecological environment. To protect the aquifers and maximize the coal resource recovery, field trials were undertaken during the operation of the LW32201 in Bulianta coal mine, Shendong, China. With a severely weathered rock (SWR) layer and two key strata (KS) in the overlying strata, aquifer protection in longwall mining (APLM) relies mainly on the rapid advance. In some localized zones, special measures should be taken to achieve the APLM, including lowering mining height, backfill and slurry injection. To further understand the mechanism and applicable conditions of the APLM and validate the effectiveness of the APLM, variation of the water table in the aquifer was observed as the longwall face passed through the zone. This paper also discusses the mechanism and basic requirements of the APLM and the relationship between the fall of the water table and the surface subsidence. The results of the field trials indicated that APLM in shallow coal seams could be successful under suitable conditions.

  1. Coal geopolitics

    Giraud, P.N.; Suissa, A.; Coiffard, J.; Cretin, D.

    1991-01-01

    This book divided into seven chapters, describes coal economic cycle. Chapter one: coals definition; the principle characteristics and properties (origin, calorific power, international classification...) Chapter two: the international coal cycle: coal mining, exploration, coal reserves estimation, coal handling coal industry and environmental impacts. Chapter three: the world coal reserves. Chapter four: the consumptions, productions and trade. Chapter five: the international coal market (exporting mining companies; importing companies; distributors and spot market operators) chapter six: the international coal trade chapter seven: the coal price formation. 234 refs.; 94 figs. and tabs [fr

  2. Longwall strata control and maintenance system - a stethoscope for longwall mining

    Park, D.W.; Deb, D. [University of Alabama, Tuscaloosa, AL (US). Dept. of Civil and Environmental Engineering

    1999-10-01

    The Longwall Strata-Control and Maintenance System (LoSCo-MS) is a software and data-communication system developed at the University of Alabama. This system integrates real-time shield monitoring, data presentation, analysis and the forecasting of forthcoming events. The main objective of this system is to provide stability information on longwall panels, including excessive shield load, low setting pressure, leg leakage, poor shield performance and imminent maintenance problems. Analyses of various mining and geological parameters were also performed to determine past and present roof characteristics and to forecast roof loading patterns for the following mining cycles, the next periodic weighting, etc. A local coal mine in the Warrior Coal Basin has adopted this system to provide daily evaluation of ground stability and maintenance problems in their longwall panels. Two years of experience with this system is covered in this paper. 4 refs., 10 figs.

  3. Carbon emission coefficient measurement of the coal-to-power energy chain in China

    Shiwei Yu; Yi-Ming Wei; Haixiang Guo; Liping Ding

    2012-01-01

    Coal-fired electricity generation has become the largest source of carbon emission in China. This study utilizes life-cycle assessment to assess the effect of carbon emissions and to calculate the coefficient of carbon emissions in coal-to-energy chains. Results show that the carbon emission coefficient of the coal-to-energy chain in China is 875 g/kW h-1, which is a relatively low level compared with that of other countries. CO2 is the main type of greenhouse gas emission and the most abunda...

  4. An evaluation of measurement uncertainties in the on-line measurement of coal ash content by gamma-ray transmission

    Wenzhong, Liu; Li, Kong; Tan, Qu; Jingjing, Cheng

    2002-01-01

    In this paper, a significant effect producing systematic errors in the on-line measurement using gamma-ray transmission is revealed. Ash content fluctuations or thickness changes lead to a permanent negative systematic error in the results of the measurements. To study uncertainties in the measurements applicable to time-independent ash content indicators and to investigate the characteristics of the radiation attenuation process, the behavior of the quantity in question is modeled with a stationary Gaussian distribution. A systematic error-producing effect has been found, and a quantitative correction is given to compensate for it. For some other quantities in question that vary in time, a linear model is used to discuss the systematic errors in the case of automated coal gangue separator. Results of experiments that demonstrate different systematic errors for different sampling intervals are presented. The reason for these errors is the nonlinearity of the relationship between the radiation intensity, on the one hand, and the sample thickness and mass attention, on the other

  5. Application of the surface reflection seismic method to shallow coal exploration in the plains of Alberta

    Lyatsky, H.V.; Lawton, D.C. (University of Victoria, Victoria, BC (Canada). Dept. of Physics and Astronomy)

    1988-12-01

    A study was done to make a quantitative interpretation of reflection seismic data from the Highvale-Whitewood shallow coal deposit in central Alberta. Results showed that the data is useful in demonstrating coal thickness and stratigraphy as well as structural formation. Reflection character is affected by nature of the strata surrounding the coal deposit. 22 refs., 1 tab., 23 figs.

  6. Numerical Simulation on the Partition of Gas-Rich Region in Overlying Strata

    G. Wang

    2014-03-01

    Full Text Available In the background of Kongzhuang coal mine 7433 working face, theoretical analysis and numerical simulation are adopted. The partition method of gas-rich region in overlying strata based on the key stratum is proposed. Overlying stratas are divided into low concentration and easy for gas drainage area, high concentration and easy for drainage area, primary stress zone according to the control action of key stratum in overlying stratas. The numerical simulation shows that fissure development range is gradually scaling up ,and the development range of bed separated fissures and vertical fissures extend to the second inferior key stratum step-by-step with the working face moving forward The fissure development range stabilizes as the roof periodic motion and moves forward with the working face moving forward. Compared to traditional empirical formula calculation result, the top boundary of high concentration and easy for drainage area according to this method is higher than the calculated limit of water flowing fractured zone. The design of gas drainage can be more accurately guided. Better gas drainage effect is obtained by the design of gas drainage in 7433 working face which is based on this method and the numerical simulation result. The effectiveness and rationality of this method are verified.

  7. On the measurment of specific energy of coals by means of 12C determination using a correlation method

    Cywicka-Jakiel, T.; Bogacz, J.; Czubek, J.A.; Dabrowski, J.M.; Loskiewicz, J.; Zazula, J.M.

    1982-01-01

    The most important industrial property of coal is its gross specific energy (combustion heat). It depends mainly on carbon concentration in coal. We propose to measure the carbon or more precisely, its 12 C content using the (n,n'γ) reaction in which 4.43 MeV gamma rays are emitted. We are using the correlation technique which can be used in high background measurements. The idea of correlation type measurement necessitates the existence of a reaction chain with primary and secondary radiations emitted and registered. By measuring the correlation or covariance function PHI we can obtain a measure of the number of excited 12 C nuclei i.e. a value which is connected to the carbon concentration. The dependence of PHI/t ratio (t being the sampling interval time) on carbon concentration shows a clear increase of the PHI/t value with carbon content. The relative standard deviations for different points vary from 1.3 to 4.4%. The preliminary results presented show that with improved experimental techniques this method can find application in industrial coal cobustion heat measurements. (author)

  8. The Palynological Investigation of Carboniferous Coal Measures In the Amasra Basin

    Yaşar ERGÖNÜL

    1960-12-01

    Full Text Available In the field of modern coal geology and palaeontology systematic studies of isolated fossil spores constitute a relatively new phase of paleobotanical research. In this paper, the content of the Megaspores in the paleophytogenetic material has been investigated. All the coal samples of this study were collected from the coal borings executed by the M. T. A. Institute in the Amasra district dining the year 1959-1960. For the maceration of the Amasra coal samples, Schultze's and Zetzsche's methods were applied. Our new Megaspore species described here are based on the morphological study. These species are referred to spore genera as defined by Potonie and Kremp (1954 and Bhardwaj (1955. As a result of this palynological study, one new genus and 14 new species have been discovered, described and stratigraphically evaluated.

  9. Evaluation of laser-induced breakdown spectroscopy (LIBS) for measurement of silica on filter samples of coal dust.

    Stipe, Christopher B; Miller, Arthur L; Brown, Jonathan; Guevara, Edward; Cauda, Emanuele

    2012-11-01

    Airborne silica dust (quartz) is common in coal mines and represents a respiratory hazard that can lead to silicosis, a potentially fatal lung disease. With an eye toward developing a portable monitoring device for rapid analysis of silica dust, laser-induced breakdown spectroscopy (LIBS) was used to quantify quartz in coal dust samples collected on filter media. Pure silica (Min-U-Sil™ 5), Georgia kaolin, and Pittsburgh-4 and Illinois-6 coal dusts were deposited separately and at multiple mass loadings onto 37-mm polyvinylchloride (PVC) filters. LIBS-generated silicon emission was monitored at 288.16 nm, and non-silica contributions to that signal from kaolinite were removed by simultaneously detecting aluminum. Measurements of the four samples were used to calculate limits of detection (LOD) for silicon and aluminum of approximately 0.08 μg/cm(2) and 0.05 μg/cm(2), respectively (corresponding to 0.16 μg/cm(2) and 0.20 μg/cm(2) for silica and kaolinite, respectively). Relative errors of prediction are around 10%. Results demonstrate that LIBS can dependably quantify silica on filter samples of coal dust and confirm that accurate quantification can be achieved for very lightly loaded samples, which supports the potential application of LIBS for rapid, in-field monitoring.

  10. Gas Concentration Prediction Based on the Measured Data of a Coal Mine Rescue Robot

    Xiliang Ma

    2016-01-01

    Full Text Available The coal mine environment is complex and dangerous after gas accident; then a timely and effective rescue and relief work is necessary. Hence prediction of gas concentration in front of coal mine rescue robot is an important significance to ensure that the coal mine rescue robot carries out the exploration and search and rescue mission. In this paper, a gray neural network is proposed to predict the gas concentration 10 meters in front of the coal mine rescue robot based on the gas concentration, temperature, and wind speed of the current position and 1 meter in front. Subsequently the quantum genetic algorithm optimization gray neural network parameters of the gas concentration prediction method are proposed to get more accurate prediction of the gas concentration in the roadway. Experimental results show that a gray neural network optimized by the quantum genetic algorithm is more accurate for predicting the gas concentration. The overall prediction error is 9.12%, and the largest forecasting error is 11.36%; compared with gray neural network, the gas concentration prediction error increases by 55.23%. This means that the proposed method can better allow the coal mine rescue robot to accurately predict the gas concentration in the coal mine roadway.

  11. Regional measurement of ventilation and perfusion to detect subtle lung abnormalities in coal miners

    Susskind, H.; Liu, J.; Brill, A.B.

    1986-01-01

    The relationship between regional pulmonary ventilation (V) and perfusion (Q) uniquely determines the amount of gas exchange that occurs in the lungs. Therefore, the pixel-by-pixel distributions of V and Q were measured with continuously inhaled Kr-81m and i.v. injected Tc-99m MAA, respectively, in a group of 71 subjects exposed to coal dust and then compared with those from a control group of 9 healthy volunteers. Each subject sat upright with his back against a large-field-of-view scintillation camera; 500,000 count images were obtained, analyzed by computer, and then displayed in a 64 x 64 matrix. Individual pixel values of V and Q were correlated by a best-fit regression line, whose slope was proportional to the overall V/Q ratio. The slopes of individual groups of nonsmokers, ex-smokers, and smokers (0.83-0.85) were significantly greater (p < 0.02) than the slope of the controls (0.70 +/- 0.07). In addition, the authors found that the skewness of plots of frequency distribution of V/Q and of V and Q vs V/Q for the individual patient groups was statistically different from that of the normals (p < 0.01). Statistical analysis of local and Q values therefore appears to be a potentially useful, non-invasive method to evaluate subtle regional lung impairment

  12. Geodesy in construction of the Belchatow brown coal mine. Geodezja w budowie KWB Belchatow

    Poltoranos, J.

    1984-01-01

    Nine papers were delivered at the conference on geodesy in construction of the Belchatow brown coal mine held in October 1984 in Belchatow. Participants representing the Belchatow mine, Technical Institutes in Warsaw and Wroclaw, the Academy of Mining and Metallurgy im. Stanislaw Staszic in Cracow, the Central Mining Institute in Katowice, other research institutes in Poland and the Ministry of Mining and Power Generation attended the conference, sponsored by the Committee of Geodesy of the Polish Academy of Sciences. The following problems were discussed: types of geodetic measuring networks used in coal surface mining, criteria for optimization of geodetic measuring networks, kinematic problems in surveying displacements in coal mines, investigating strata movement in slopes of large and deep coal surface mines using geodetic surveying, mine surveying in the Belchatow mine, recommendations for amendment of regulations for geodetic surveying in coal surface mines in Poland, character of coal deposit in the Belchatow fault valley, its origin and geology, and causes of seismicity induced by mining in Belchatow. Eight papers have been abstracted separately.

  13. Excavating wide inclines in weak strata

    Kuznetsov, N N [Ukrspetsstroiproekt (USSR)

    1990-09-01

    Discusses schemes for excavation of transport inclines in surface mines under conditions of weak, unstable rocks characterized by a high water content. The schemes are aimed at maximum reduction of excavation operations without infringing the safety of personnel. Use of walking draglines (the EhSh-20/90, EhSh-100/100 and EhSh-10/70) is evaluated. Optimum schemes for incline excavation and determining optimum slope inclination are described on the example of the Berezovsk brown coal surface mine in the USSR. Efficiency of optimum schemes is analyzed: range of excavation, safety degree, landslide hazards, water influx rate, accident rate, etc.

  14. Design of permanent block stopping to resist strata convergence

    Ray, R.E.

    1985-11-01

    Conventional concrete block plastered with a cementitious coating is the most common material used in the construction of permanent stoppings to direct airflow in underground mines in the US. All mines experience various degrees of strata convergence depending on depth of overburden, geological conditions, and type of roof support employed. Strata convergence will cause cracks and joint openings in masonry stoppings, resulting in significant air leakage losses. Where strata convergence is severe, complete structural failure of the stopping can ultimately occur. Reconstruction of damaged or destroyed stoppings adds expensive overheads to mining operations, and even greater expenses are incurred from the additional fan horsepower required to overcome leakage losses. Ideally, a stopping should maintain high resistance to airflow while yielding to strata convergence. By properly incorporating a polyisocyanurate rigid foam material within the masonry block structure, stopping service life can be increased in mines experiencing strata convergence problems such as floor heave, roof loading, and lateral rib movement.

  15. Large-Strain Monitoring Above a Longwall Coal Mine With GPS and Seismic Measurements

    Swanson, P. L.; Andreatta, V.; Meertens, C. M.; Krahenbuhl, T.; Kenner, B.

    2001-12-01

    As part of an effort to evaluate continuous GPS measurements for use in mine safety studies, a joint GPS-seismic experiment was conducted at an underground longwall coal mine near Paonia, Colorado in June, 2001. Seismic and deformation signals were measured using prototype low-cost monitoring systems as a longwall panel was excavated 150 m beneath the site. Data from both seismic and GPS instruments were logged onto low-power PC-104 Linux computers which were networked using a wireless LAN. The seismic system under development at NIOSH/SRL is based on multiple distributed 8-channel 24-bit A/D converters. The GPS system uses a serial single-frequency (L1) receiver and UNAVCO's "Jstream" Java data logging software. For this experiment, a continuously operating dual-frequency GPS receiver was installed 2.4 km away to serve as a reference site. In addition to the continuously operating sites, 10 benchmarks were surveyed daily with short "rapid-static" occupations in order to provide greater spatial sampling. Two single-frequency sites were located 35 meters apart on a relatively steep north-facing slope. As mining progressed from the east, net displacements of 1.2 meters to the north and 1.65 meters of subsidence were observed over a period of 6 days. The east component exhibited up to 0.45 meters of eastward displacement (toward the excavation) followed by reverse movement to the west. This cycle, observed approximately two days earlier at the eastern L1 site, is consistent with a change in surface strain from tension to compression as the excavation front passed underneath. As this strain "wave" propagated across the field site, surface deformation underwent a cycle of tension crack nucleation, crack opening (up to 15 cm normal displacements), subsequent crack closure, and production of low-angle-thrust compressional deformation features. Analysis of seismic results, surface deformation, and additional survey results are presented.

  16. A practical application of photogrammetry to performing rib characterization measurements in an underground coal mine using a DSLR camera.

    Slaker, Brent A; Mohamed, Khaled M

    2017-01-01

    Understanding coal mine rib behavior is important for inferring pillar loading conditions as well as ensuring the safety of miners who are regularly exposed to ribs. Due to the variability in the geometry of underground openings and ground behavior, point measurements often fail to capture the true movement of mine workings. Photogrammetry is a potentially fast, cheap, and precise supplemental measurement tool in comparison to extensometers, tape measures, or laser range meters, but its application in underground coal has been limited. The practical use of photogrammetry was tested at the Safety Research Coal Mine, National Institute for Occupational Safety and Health (NIOSH). A commercially available, digital single-lens reflex (DSLR) camera was used to perform the photogrammetric surveys for the experiment. Several experiments were performed using different lighting conditions, distances to subject, camera settings, and photograph overlaps, with results summarized as follows: the lighting method was found to be insignificant if the scene was appropriately illuminated. It was found that the distance to the subject has a minimal impact on result accuracy, and that camera settings have a significant impact on the photogrammetric quality of images. An increasing photograph resolution was preferable when measuring plane orientations; otherwise a high point cloud density would likely be excessive. Focal ratio (F-stop) changes affect the depth of field and image quality in situations where multiple angles are necessary to survey cleat orientations. Photograph overlap is very important to proper three-dimensional reconstruction, and at least 60% overlap between photograph pairs is ideal to avoid unnecessary post-processing. The suggestions and guidelines proposed are designed to increase the quality of photogrammetry inputs and outputs as well as minimize processing time, and serve as a starting point for an underground coal photogrammetry study.

  17. The Tiptop coal-mine fire, Kentucky: Preliminary investigation of the measurement of mercury and other hazardous gases from coal-fire gas vents

    Hower, James C.; Henke, Kevin [University of Kentucky Center for Applied Energy Research, Lexington, KY 40511 (United States); O' Keefe, Jennifer M.K. [Morehead State University, Morehead, KY 40351 (United States); Engle, Mark A. [U.S. Geological Survey, Reston, VA 20192 (United States); Blake, Donald R. [Department of Chemistry, University of California - Irvine, Irvine, CA 92697 (United States); Stracher, Glenn B. [East Georgia College, Swainsboro, GA 30401 (United States)

    2009-10-01

    The Tiptop underground coal-mine fire in the Skyline coalbed of the Middle Pennsylvanian Breathitt Formation was investigated in rural northern Breathitt County, Kentucky, in May 2008 and January 2009, for the purpose of determining the concentrations of carbon dioxide (CO{sub 2}), carbon monoxide (CO), and mercury (Hg) in the vent and for measuring gas-vent temperatures. At the time of our visits, concentrations of CO{sub 2} peaked at 2.0% and > 6.0% (v/v) and CO at 600 ppm and > 700 ppm during field analysis in May 2008 and January 2009, respectively. For comparison, these concentrations exceed the U.S. Occupational Safety and Health Administration (OSHA) eight-hour safe exposure limits (0.5% CO{sub 2} and 50 ppm CO), although the site is not currently mined. Mercury, as Hg{sup 0}, in excess of 500 and 2100 {mu}g/m{sup 3}, in May and January, respectively, in the field, also exceeded the OSHA eight-hour exposure limit (50 {mu}g/m{sup 3}). Carbonyl sulfide, dimethyl sulfide, carbon disulfide, and a suite of organic compounds were determined at two vents for the first sampling event. All gases are diluted by air as they exit and migrate away from a gas vent, but temperature inversions and other meteorological conditions could lead to unhealthy concentrations in the nearby towns. Variation in gas temperatures, nearly 300 C during the January visit to the fire versus < 50 C in May, demonstrates the large temporal variability in fire intensity at the Tiptop mine. These preliminary results suggest that emissions from coal fires may be important, but additional data are required that address the reasons for significant variations in the composition, flow, and temperature of vent gases. (author)

  18. Modeling of multi-strata forest fire severity using Landsat TM data

    Q. Meng; R.K. Meentemeyer

    2011-01-01

    Most of fire severity studies use field measures of composite burn index (CBI) to represent forest fire severity and fit the relationships between CBI and Landsat imagery derived differenced normalized burn ratio (dNBR) to predict and map fire severity at unsampled locations. However, less attention has been paid on the multi-strata forest fire severity, which...

  19. Potential of using stable nitrogen isotope ratio measurements to resolve fuel and thermal NOx in coal combustion

    Chenggong Sun; Janos Lakatos; Colin E. Snape; Tony Fallick [University of Nottingham, Nottingham (United Kingdom). School of Chemical, Environmental and Mining Engineering (SChEME)

    2003-07-01

    In order to examine the potential of applying isotopic analysis to apportion NOx formation from different mechanisms, stable nitrogen isotope ratio measurements have been conducted on a number of thermal/prompt (diesel) and actual (coal) PF NO samples generated from a 1MW test facility at Powergen (UK), together with measurements on a range of pyrolysis and combustion chars obtained from a drop-tube reactor. A highly effective nitrogen-free sorbent, derived from white sugar with Mn as promoter, has been developed using an innovative procedure. This adsorbent has facilitated, for the first time, the determination of {delta}{sup 15}N values without background corrections. The isotopic data indicate that the thermal/prompt NOx collected during start-up with diesel as fuel has a {delta}{sup 15}N of close to 6.5(per thousand) compared to +15(per thousand) for the actual PF sample analysed. Thus, differences of up to ca. 20(per thousand) have been found to exist between thermal and PF fuel (char) NOx isotopic values. This augurs very well for the further development of the approach in order to help quantify the extent of thermal/prompt NOx formation in PF combustion. Measurements on chars have indicated that the extent of isotopic fractionation that occurs between coal-N and NOx from char is related to the reactivity of coals. Further, it would appear that much of the isotopic fractionation that occurs between coal nitrogen and fuel NO arises in the formation of char, although further fractionation can be inferred to occur during char combustion. In contrast, a lesser degree of isotopic fractionation is associated with the formation of thermal NO (ca. 6(per thousand)), atmospheric nitrogen having a value of 0(per thousand). 4 refs., 6 tabs.

  20. Results of dust precipitation and airborne dust measurements in the Rhineland Brown Coal Mining Area in 1991 and 1992

    Respondek, A.; Stein, W.

    1994-01-01

    In the Rhineland brown coal mining area the immission value of IW 1 = 0.35 g/(m 2 xd), as stipulated in the Technical Specifications for Air Pollution Control, was not reached anywhere in the entire above-mentioned measured area in 1991. The maximum monthly pollution load, i.e. I 2 = 0.52 g/(m 2 xd), was less than the immission value IW 2 = 0.65 g/(m 2 xd). In the measured areas under review, Rheinschiene South and Rheinschiene Centre, the values for airborne dust immission I 1 in 1991 were also less than 50% of the IW 1 value of 0.15 mg/m 3 . In view of these results and also - the measurements carried out by the LIS (State Pollution Control Authority) over many years in the townships of Kerpen, Frechen-Bachem, Huerth-Hermuelheim, Horrem, Frechen and Pulheim. - A special measurement carried out by the LIS in the Erft district and in the south of the Neuss district in 1983, and - the measurements carried out in accordance with the specifications for the licensing and development plan procedures, as well as - the results of the special measurement programme carried out in the community of Elsdorf in 1988 and 1989, there is no reason to fear that harmful effects on the environment will be caused by brown coal opencast mines and coal processing plants as a result of airborne dust. The dust precipitation measurements carried out at the request of the Cologne Mines Inspectorate revealed that in 1992 none of the values measured exceeded the IW 1 value. The highest measured I 1 value was 0.21 g/(m 2 xd), i.e. 60% of the IW 1 value. The average pollution load was 0.13 g/(m 2 xd), i.e. 37%. (orig./MSK) [de

  1. Ground level measurement of nuclei from coal development in the northern Great Plains: baseline measurements. Final report

    Davis, B. L.; Johnson, L. R.; Sengupta, S.; Yue, P. C.

    1978-11-01

    The Institute of Atmospheric Sciences of the South Dakota School of Mines and Technology has completed 20 months of ambient air sampling at rural and remote sites in a five-state region of the northern Great Plains. Sampling was accomplished by use of a 27-ft motor home laboratory containing living accommodations for a field crew of two. The laboratory was outfitted with a number of instruments for measurement of pollutant parameters: cloud condensation nuclei, ice nuclei, Aitken nuclei, size distribution information for Aitken size particulate, sulfur dioxide, ozone, raindrop size distributions, and pH of precipitation. In addition, an instrumented meteorological tower provided wind speed, wind direction, ambient air temperature, and dew-point temperature. Instruments varied as to durability and success of operation, but better than 90% data retrieval was possible for the entire 20-month sampling study. Analyses of the large quantities of data obtained were not possible under the initial baseline measurement program, but examination of most parameters indicate that the air masses in the northern Great Plains are still relatively clean and are influenced primarily by local sources of contamination rather than large regional sources. Particulate concentrations in these remote areas are representative of mountain stations or clean rural conditions, and sulfur dioxide concentrations are at the threshold of detectability of the instrument. Precipitation is only very slightly acidic, and no significant quantity of amorphous particles (such as coal dust or combustion products) is found in the quantitative analyses of the high-volume filter collections. A summary of ''average'' conditions observed over the study area is tabulated.

  2. A systematic approach to assessing measurement uncertainty for CO2 emissions from coal-fired power plants

    Wagner, Claas; Esbensen, Kim

    2011-01-01

    An augmented measurement uncertainty approach for CO2 emissions from coal-fired power plants with a focus on the often forgotten contributions from sampling errors occurring over the entire fuel-to-emission pathway is presented. Current methods for CO2 emission determination are evaluated in detail......, from which a general matrix scheme is developed that includes all factors and stages needed for total CO2 determination, which is applied to the monitoring plan of a representative medium-sized coal-fired power plant. In particular sampling involved significant potential errors, as identified...... of these three materials were also given full attention. A systematic error (bias) is present in the current sampling approach, which increases the present uncertainty estimate unnecessarily. For both primary sampling and analytical sample extraction steps, random variations, which hitherto only have been...

  3. Thermal expansion of coking coals

    Orlik, M.; Klimek, J. (Vyzkumny a Zkusebni Ustav Nova Hut, Ostrava (Czechoslovakia))

    1992-12-01

    Analyzes expansion of coal mixtures in coke ovens during coking. Methods for measuring coal expansion on both a laboratory and pilot plant scale are comparatively evaluated. The method, developed, tested and patented in Poland by the Institute for Chemical Coal Processing in Zabrze (Polish standard PN-73/G-04522), is discussed. A laboratory device developed by the Institute for measuring coal expansion is characterized. Expansion of black coal from 10 underground mines in the Ostrava-Karvina coal district and from 9 coal mines in the Upper Silesia basin in Poland is comparatively evaluated. Investigations show that coal expansion reaches a maximum for coal types with a volatile matter ranging from 20 to 25%. With increasing volatile matter in coal, its expansion decreases. Coal expansion increases with increasing swelling index. Coal expansion corresponds with coal dilatation. With increasing coal density its expansion increases. Coal mixtures should be selected in such a way that their expansion does not cause a pressure exceeding 40 MPa. 11 refs.

  4. Comparison of phytosociological parameters among three strata of a fragment of ombrophylous mixed forest

    Sebastião do Amaral Machado

    2013-09-01

    Full Text Available Phytosociological studies based on sampling have been very common in the last 20 years, however, they are rarely carried out using complete enumeration of trees (census. This research compare the phytossociological parameters between three different strata from a remnant of Ombrophylous Mixed Forest (OMF, which are: OMF Montana, Border OMF Montana and OMF Alluvial. The area of 13.71 was topographically divided in blocks of 50 x 50 meters for a better control of the 100% forest inventory (census. All trees with CBH (circumference measured at 1,30 m above ground ≥ 31,5 centimeters were measured, georeferencied, numbered, painted at DBH and identified at species level. In the strata OMF Montana the species with the highest Value of Coverage (VC was Araucaria angustifolia, with 30.6%, followed by Casearia sylvestris with 25.8%. In the Border OMF Montana the species that succeeded Araucaria angustifolia (29.0% was Gochnatia polymorpha with 27.2% of VC. The third strata, OMF Alluvial, presented as predominant species Schinus terebinthifolius (55,5%, followed by Sebastiania commersoniana (27,7%, both characteristics of alluvial environments. In the three strata there was prevalence of secondary pioneer species, proving that the area is in a secondary stage of ecological succession due to past exploratory process.

  5. Similar simulation study on the characteristics of the electric potential response to coal mining

    Niu, Yue; Li, Zhonghui; Kong, Biao; Wang, Enyuan; Lou, Quan; Qiu, Liming; Kong, Xiangguo; Wang, Jiali; Dong, Mingfu; Li, Baolin

    2018-02-01

    An electric potential (EP) can be generated during the failure process of coal and rock. In this article, a similar physical model of coal rock was built and the characteristics of the EP responding to the process of coal mining were studied. The results showed that, at the early mining stage, the structure of coal rock strata were stable in the simulation model, the support stress of overlying coal rock strata was low and the maximum subsidence was little, while the EP change was less. With the advancement of the working face, the support stress of the overlying coal rock strata in the mined-out area changed dramatically, the maximum subsidence increased constantly, the deformation and destruction were aggravated, and cracks expanded continuously. Meanwhile, the EP response was significant with fluctuation. When significant macro damage appeared in coal rock strata, the EP signal fluctuation was violent. The overlying coal rock strata were influenced by gravity and mining activity. During the mining process, the crack growth and the friction, together with slip between coal and rock particles, resulted in the response of EP. The change in EP was closely related to the damage state and stress distribution of the coal rock strata. EP monitoring has the advantages of accurate reflection and strong anti-interference in the field. Therefore, with further study, an EP monitoring method could be applied for monitoring and early warning of coal and rock dynamic disaster, and risk evaluation in the future. The strength of the EP and its fluctuation degree could serve as the key discrimination indexes.

  6. Prospecting for coal in China with remote sensing

    Ke-long Tan; Yu-qing Wan; Sun-xin Sun; Gui-bao Bao; Jing-shui Kuang [Aerophotogrammetry and Remote Sensing Center of China Coal, Xi' an (China)

    2008-12-15

    In China it is important to explore coal prospecting by taking advantage of modern remote sensing and geographic information system technologies. Given a theoretical basis for coal prospecting by remote sensing, the methodologies and existing problems are demonstrated systematically by summarizing past practices of coal prospecting with remote sensing. A new theory of coal prospecting with remote sensing is proposed. In uncovered areas, coal resources can be prospected by direct interpretation. In coal bearing strata of developed areas covered by thin Quaternary strata or vegetation, prospecting for coal can be carried out by indirect interpretation of geomorphology and vegetation. For deeply buried underground deposits, coal prospecting can rely on tectonic structures, interpretation and analysis of new tectonic clues and regularity of coal formation and preservation controlled by tectonic structures. By applying newly hyper-spectral, multi-polarization, multi-angle, multi-temporal and multi-resolution remote sensing data and carrying out integrated analysis of geographic attributes, ground attributes, geophysical exploration results, geochemical exploration results, geological drilling results and remote sensing data by GIS tools, coal geology resources and mineralogical regularities can be explored and coal resource information can be acquired with some confidence. 12 refs., 4 figs., 3 tabs.

  7. The Tiptop coal-mine fire, Kentucky: Preliminary investigation of the measurement of mercury and other hazardous gases from coal-fire gas vents

    Hower, James C.; Henke, Kevin R.; O'Keefe, Jennifer M.K.; Engle, Mark A.; Blake, Donald R.; Stracher, Glenn B.

    2009-01-01

    The Tiptop underground coal-mine fire in the Skyline coalbed of the Middle Pennsylvanian Breathitt Formation was investigated in rural northern Breathitt County, Kentucky, in May 2008 and January 2009, for the purpose of determining the concentrations of carbon dioxide (CO2), carbon monoxide (CO), and mercury (Hg) in the vent and for measuring gas-vent temperatures. At the time of our visits, concentrations of CO2 peaked at 2.0% and > 6.0% (v/v) and CO at 600 ppm and > 700 ppm during field analysis in May 2008 and January 2009, respectively. For comparison, these concentrations exceed the U.S. Occupational Safety & Health Administration (OSHA) eight-hour safe exposure limits (0.5% CO2 and 50 ppm CO), although the site is not currently mined. Mercury, as Hg0, in excess of 500 and 2100 μg/m3, in May and January, respectively, in the field, also exceeded the OSHA eight-hour exposure limit (50 μg/m3). Carbonyl sulfide, dimethyl sulfide, carbon disulfide, and a suite of organic compounds were determined at two vents for the first sampling event. All gases are diluted by air as they exit and migrate away from a gas vent, but temperature inversions and other meteorological conditions could lead to unhealthy concentrations in the nearby towns.

  8. Trends of multiple air pollutants emissions from residential coal combustion in Beijing and its implication on improving air quality for control measures

    Xue, Yifeng; Zhou, Zhen; Nie, Teng; Wang, Kun; Nie, Lei; Pan, Tao; Wu, Xiaoqing; Tian, Hezhong; Zhong, Lianhong; Li, Jing; Liu, Huanjia; Liu, Shuhan; Shao, Panyang

    2016-10-01

    Residential coal combustion is considered to be an important source of air pollution in Beijing. However, knowledge regarding the emission characteristics of residential coal combustion and the related impacts on the air quality is very limited. In this study, we have developed an emission inventory for multiple hazardous air pollutants (HAPs) associated with residential coal combustion in Beijing for the period of 2000-2012. Furthermore, a widely used regional air quality model, the Community Multi-Scale Air Quality model (CMAQ), is applied to analyze the impact of residential coal combustion on the air quality in Beijing in 2012. The results show that the emissions of primary air pollutants from residential coal combustion have basically remained the same levels during the past decade, however, along with the strict emission control imposed on major industrial sources, the contribution of residential coal combustion emissions to the overall emissions from anthropogenic sources have increased obviously. In particular, the contributions of residential coal combustion to the total air pollutants concentrations of PM10, SO2, NOX, and CO represent approximately 11.6%, 27.5%, 2.8% and 7.3%, respectively, during the winter heating season. In terms of impact on the spatial variation patterns, the distributions of the pollutants concentrations are similar to the distribution of the associated primary HAPs emissions, which are highly concentrated in the rural-urban fringe zones and rural suburb areas. In addition, emissions of primary pollutants from residential coal combustion are forecasted by using a scenario analysis. Generally, comprehensive measures must be taken to control residential coal combustion in Beijing. The best way to reduce the associated emissions from residential coal combustion is to use economic incentive means to promote the conversion to clean energy sources for residential heating and cooking. In areas with reliable energy supplies, the coal used

  9. Clean coal technologies

    Bourillon, C.

    1994-01-01

    In 1993 more than 3.4 billion tonnes of coal was produced, of which half was used to generate over 44 per cent of the world's electricity. The use of coal - and of other fossil fuels- presents several environmental problems such as emissions of sulphur dioxide (SO 2 ), nitrogen oxides (NO 2 ), and carbon dioxide (CO 2 ) into the atmosphere. This article reviews the measures now available to mitigate the environmental impacts of coal. (author)

  10. Study on the Concentration Measurement of the Pollution Gases from Coal-Fired Power Station

    Zheng, L J; Li, W

    2006-01-01

    CO 2 is a main kind of pollution gases discharged from coal-fired power station. The relationship between gas concentration and pressure, temperature is deduced base on the law of Beer-Lambert and the theory of gas line-shape. The tunable diode laser spectral technology is used to analyze the changing regularity of the peak, half-peak width of the absorption curve with pressure and temperature

  11. Dew point measurements of flue gases in steam generators with brown coal combustion

    Schinkel, W.

    1980-01-01

    This paper examines empirical data on sulfuric acid condensation and resulting internal corrosion in brown coal fired steam generators. Due to the high sulfur content in brown coal (0.5% to 5.0%) and relative short duration of the gases in the combustion chamber the concentrations of sulfur trioxide present in the flue gases can condense at the heat exchange surfaces of the steam generators. A number of diagrams show sulfuric acid dew point temperatures depending on brown coal sulfur content, the influence of combustion air supply on the dew point, and condensing speed and the rate of corrosion in relation to different heat exchange surface temperatures. The conclusion is made that a five-fold increase in corrosion can be caused by a 10 K higher flue gas dew point, a 5 K cooling of heating surfaces can also cause heavy corrosion at a certain dew point. Maximum corrosion results at 20 to 50 K differences between flue gas dew point and heat exchange surfaces. Optimum operation of steam generators with minimal internal corrosion requires the consideration of flue gas and heating surface temperatures as well as flue gas sulfur acid dew points. (10 refs.) (In German)

  12. Nanometre-sized pores in coal: Variations between coal basins and coal origin

    Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

    2018-01-01

    We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

  13. A study of calcium intake and sources of calcium in adolescent boys and girls from two socioeconomic strata, in Pune, India.

    Sanwalka, Neha J; Khadilkar, Anuradha V; Mughal, M Zulf; Sayyad, Mehmood G; Khadilkar, Vaman V; Shirole, Shilpa C; Divate, Uma P; Bhandari, Dhanshari R

    2010-01-01

    Adequate intake of calcium is important for skeletal growth. Low calcium intake during childhood and adolescence may lead to decreased bone mass accrual thereby increasing the risk of osteoporotic fractures. Our aim was to study dietary calcium intake and sources of calcium in adolescents from lower and upper economic strata in Pune, India. We hypothesized that children from lower economic strata would have lower intakes of calcium, which would predominantly be derived from non-dairy sources. Two hundred male and female adolescents, from lower and upper economic stratum were studied. Semiquantitative food frequency questionnaire was used to evaluate intakes of calcium, phosphorus, oxalic acid, phytin, energy and protein. The median calcium intake was significantly different in all four groups, with maximum intake in the upper economic strata boys (893 mg, 689-1295) and lowest intake in lower economic strata girls (506 mg, 380-674). The median calcium intake in lower economic strata boys was 767 mg (585-1043) and that in upper economic strata girls was 764 mg (541-959). The main source of calcium was dairy products in upper economic strata adolescents while it was dark green leafy vegetables in lower economic strata adolescents. The median calcium intake was much lower in lower economic strata than in the upper economic strata both in boys and girls. Girls from both groups had less access to dairy products as compared to boys. Measures need to be taken to rectify low calcium intake in lower economic strata adolescents and to address gender inequality in distribution of dairy products in India.

  14. 穿层孔吞吐压裂水力强化抽采技术研究及应用%Research and application of gas drainage with hydraulic reinforcement of water stimulation fracture in borehole through strata

    辛新平; 高建良; 马耕

    2014-01-01

    为了解决低透气性煤层高效抽采的难题,采用穿层孔吞吐压裂水力强化改善煤层透气性。分析了水力强化工艺穿层孔瓦斯运移产出过程,研究了水力强化对硬煤储层和软煤层中瓦斯渗透率的影响,分析了水力强化对煤体渗透率的作用及增透机理,并进行了现场效果应用。结果表明:穿层孔吞吐压裂技术提高了煤层透气性,形成瓦斯产出通道,在硬煤中水力强化可在顶底板形成“虚拟储层”,瓦斯以渗流为主,软煤中以扩散运移为主;吞吐压裂水力强化通过形成洞穴和裂隙,增加煤层渗透性,减少瓦斯抽采流量衰减系数,提高瓦斯抽采效率。现场实施吞吐压裂水力措施后抽采纯量由14.8 m³增加至31.9~42.8 m³;抽采体积分数由14.1%增加至73.9%~77.5%,该技术具有较高的实际推广应用价值。%In order to solve the problem of how to efficiently extract the coal seam with low permeabil-ity, the hydraulic measures of stimulation fracturing through strata borehole has been adopted to im-prove the permeability of coal seam. The gas migration process through borehole in the hydraulic en-hanced technology has been analyzed. The effect of hydraulic reinforcement measures on hard and soft coal seam permeability has been studied, and the effect and mechanism of hydraulic reinforcement on the permeability of coal mass has been analyzed, and finally, the field experiment of hydraulic fracturing has been carried out. Research results show that the hydraulic measures of stimulation fracturing through strata borehole technology can improve the permeability of coal seam and contribute to form gas flow channel. There is“virtual reservoir”in roof and floor in hard coal seam and the gas shows see-page mainly, while, in soft coal seam gas shows diffusion migration mainly. The hydraulic measures of stimulation fracturing can increase the permeability of coal seam through

  15. Effect of structural discontinuities on coal pillar strength as a basis for improving safety in the design of coal pillar systems.

    Esterhuizen, GS

    1998-12-01

    Full Text Available The stability of underground coal mines depends on the integrity of the pillars which are required to support the overlying strata. Should the pillars collapse, the safety of the persons in the workings will be threatened. The strength of a coal...

  16. Development of I and C system for the coal feeder of coal firing plant

    Kim, Teak Soo; Park, Chan Ho [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

    1996-12-31

    KECC(Kepco Coal Feeder Control System) receives coal weight, conveyor speed and boiler demand signals. It controls coal flow by generating speed signal of feeder which conveys coal in hopper to pulverizer, displaying measured coal quantity and providing local auto and manual manipulator (author). 33 figs.

  17. SVM-based multisensor data fusion for phase concentration measurement in biomass-coal co-combustion

    Wang, Xiaoxin; Hu, Hongli; Jia, Huiqin; Tang, Kaihao

    2018-05-01

    In this paper, the electrical method combines the electrostatic sensor and capacitance sensor to measure the phase concentration of pulverized coal/biomass/air three-phase flow through data fusion technology. In order to eliminate the effects of flow regimes and improve the accuracy of the phase concentration measurement, the mel frequency cepstrum coefficient features extracted from electrostatic signals are used to train the Continuous Gaussian Mixture Hidden Markov Model (CGHMM) for flow regime identification. Support Vector Machine (SVM) is introduced to establish the concentration information fusion model under identified flow regimes. The CGHMM models and SVM models are transplanted on digital signal processing (DSP) to realize on-line accurate measurement. The DSP flow regime identification time is 1.4 ms, and the concentration predict time is 164 μs, which can fully meet the real-time requirement. The average absolute value of the relative error of the pulverized coal is about 1.5% and that of the biomass is about 2.2%.

  18. Distributed Temperature Measurement in a Self-Burning Coal Waste Pile through a GIS Open Source Desktop Application

    Lia Duarte

    2017-03-01

    Full Text Available Geographical Information Systems (GIS are often used to assess and monitor the environmental impacts caused by mining activities. The aim of this work was to develop a new application to produce dynamic maps for monitoring the temperature variations in a self-burning coal waste pile, under a GIS open source environment—GIS-ECOAL (freely available. The performance of the application was evaluated with distributed temperature measurements gathered in the S. Pedro da Cova (Portugal coal waste pile. In order to obtain the temperature data, an optical fiber cable was disposed over the affected area of the pile, with 42 location stakes acting as precisely-located control points for the temperature measurement. A monthly data set from July (15 min of interval was fed into the application and a video composed by several layouts with temperature measurements was created allowing for recognizing two main areas with higher temperatures. The field observations also allow the identification of these zones; however, the identification of an area with higher temperatures in the top of the studied area was only possible through the visualization of the images created by this application. The generated videos make possible the dynamic and continuous visualization of the combustion process in the monitored area.

  19. The Alabama, U.S.A., seismic event and strata collapse of May 7, 1986

    Long, L.T.; Copeland, C.W.

    1989-01-01

    On May 7, 1986, the residents of Tuscaloosa, Alabama, felt a seismic event of local magnitude 3.6 that occurred at the same time as a rock burst and roof collapse in an active longwall coal mine. Visual inspection of the seismograms reveals a deficiency in energy at frequencies above 20 Hz compared to tectonic earthquakes or surface blasts. The predominance of energy below 5 Hz may explain reports of body wave magnitudes (mb) greater than 4.2. Also, 1.0 Hz surface waves were more strongly excited than body waves and may explain local felt effects more typically associated with greater epicentral distances. All recorded first motions were dilatational. The concentration of stations in the northern hemisphere allows reverse motion on an east-trending near-vertical plane or strike-slip motion on northwest or southeast trending planes. The reverse focal mechanism is preferred, because the area of roof collapse and the area of active longwall mining are located between two east-striking loose vertical fracture zones. The characteristics of the seismic event suggest that it might have been sudden shear failure resulting from accumulated strain energy in overlying strata behind an active longwall. Although an alternate interpretation of the focal mechanism as an implosion or shear failure in the strata above previously mined out areas is also allowed by the first motion data, this alternate intepretation is not supported by geological data. ?? 1989 Birkha??user Verlag.

  20. New coal

    1979-07-01

    Specially dedicated to coal, this edition comprises a series of articles of general interest dealing with the position of the French coalmining industry (interview with M.P. Gardent), the coal market in France, the work of CERCHAR, etc. New techniques, in-situ gasification of deep coal, gasification of coal by nuclear methods, the conversion of coal into petrol, the Emile Huchet power plant of Houilleres du Bassin de Lorraine, etc., are dealt with.

  1. Coal upgrading

    Nunes, S. [IEA Clean Coal Centre, London (United Kingdom)

    2009-10-15

    This report examines current technologies and those likely to be used to produce cleaner coal and coal products, principally for use in power generation and metallurgical applications. Consideration is also given to coal production in the leading coal producing countries, both with developed and developing industries. A range of technologies are considered. These include the coal-based liquid fuel called coal water mixture (CWM) that may compete with diesel, the production of ultra-clean coal (UCC) and coal liquefaction which competes with oil and its products. Technologies for upgrading coal are considered, especially for low rank coals (LRC), since these have the potential to fill the gap generated by the increasing demand for coal that cannot be met by higher quality coals. Potential advantages and downsides of coal upgrading are outlined. Taking into account the environmental benefits of reduced pollution achieved through cleaner coal and reduced transport costs, as well as other positive aspects such as a predictable product leading to better boiler design, the advantages appear to be significant. The drying of low rank coals improves the energy productively released during combustion and may also be used as an adjunct or as part of other coal processing procedures. Coal washing technologies vary in different countries and the implications of this are outlined. Dry separation technologies, such as dry jigging and electrostatic separation, are also described. The demonstration of new technologies is key to their further development and demonstrations of various clean coal technologies are considered. A number of approaches to briquetting and pelletising are available and their use varies from country to country. Finally, developments in upgrading low rank coals are described in the leading coal producing countries. This is an area that is developing rapidly and in which there are significant corporate and state players. 81 refs., 32 figs., 3 tabs.

  2. Fiscal 1995 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system` (interim report); 1995 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku: sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho (chukan hokoku)

    NONE

    1996-03-01

    The coal utilization is expected to make substantial growth according to the long-term energy supply/demand plan. To further expand the future coal utilization, however, it is indispensable to reduce environmental loads in its total use with other energies, based on the coal use. In this survey, a regional model survey was conducted as environmental load reduction measures using highly cleaned coal which were taken in fiscal 1993 and 1994. Concretely, a model system was assumed which combined facilities for mixed combustion with coal and other energy (hull, bagasse, waste, etc.) and facilities for effective use of burned ash, and potential reduction in environmental loads of the model system was studied. The technology of mixed combustion between coal and other energy is still in a developmental stage with no novelties in the country. Therefore, the mixed combustion technology between coal and other energy is an important field which is very useful for the future energy supply/demand and environmental issues. 34 refs., 27 figs., 48 tabs.

  3. Quantitative determination of mineral coal impurities from Brazil through optical emission spectrography technique

    Clain, Almir Faria

    1982-01-01

    The aim of the present research was to develop a spectrographic technique to determine the highest possible number of the chemical elements micro-constituents of Brazilian mineral coals. The experimental technique developed corresponds to the so called total-burning procedure. Coal samples were calcined to ashes at 400°C and then totally burned in graphite electrodes by a DC arc. The spectrographic measurements were made in a Jarrell-Ash emission spectrograph, Ebert mounting type, model Mark IV. An inert atmosphere chamber (for a gaseous mixture 20% 0 2 and 80% air) and a seven step rotating sector were used as main accessories. The analytical curves for the different elements, were obtained using synthetic standards in the concentration range of 10 to 1.000 ppm, and the standards as well as the coal ashes were diluted with spectrographically pure graphite in 1:1 ratio. Seventeen coal samples from different shells and strata of Morungava and Charqueadas mines - Rio Grande do Sul State - were analyzed to test the proposed technique, being possible to determine the following elements: B, Be, Bi, Cd, Co, Cr, Cu, Ga,Pb, Ge, Mn, Mo, Ni, Sn, Sb, V, Y, Zn and Zr. The coefficient of variation was 14% in average for all the elements and the sensitivity was so that the majority of the impurities present in the coals were analyzed. (author)

  4. Waterwall corrosion evaluation in coal-fired boilers using electrochemical measurements

    Davis, K.; Lee, C.; Seeley, R.; Harding, S.; Heap, M.; Cox, W.

    2000-07-01

    Until recently, waterwall corrosion in North American coal-fired boilers was uncommon and relatively mild. However, the introduction of combustion modifications to reduce in-furnace NOx formation has led to notable increases in the frequency and severity of waterwall wastage. Reaction Engineering International (REI) has worked with the Department of Energy and EPRI to improve predictive capabilities and provide solutions for furnace wall wastage for a wide range of coal-fired furnaces. To date, this work has emphasized computational simulations. More recently, REI in partnership with Corrosion Management has begun complementary efforts to improve their services by evaluating technologies capable of determining the location/rate of high water wall wastage resulting from corrosion. After an evaluation of commercially available options, electrochemical noise (EN) technology has been chosen for continued development. This approach has been successfully applied to corrosion-related problems involving acid dewpoint corrosion in flue gas ductwork, FGD systems, cooling water systems, oil and gas production, and acid cleaning (Cox et al, 1999). This paper presents the results of preliminary testing of an EN probe in a high temperature environment typical of the lower furnace of a cyclone-fired boiler operating under staged conditions. The relationship between electrochemical responses and (1) stoichiometry and (2) local hydrogen sulfide concentration is investigated and the qualitative and quantitative usefulness of the approach for on-line risk management is considered.

  5. Coal-92

    Hillring, B.; Sparre, C.

    1992-11-01

    Swedish consumption of coal and coke during 1991 and trends in technology, environment and market aspects of coal use are reported. Steam coal use in the heating sector was unchanged from 1991, 1.2 Mtons. Reduced consumption in smaller district heating units (due to conversion to biofuels and gas) was compensated by increased use for power generation in cogeneration plants. Coal consumption in industry fell 0.10 Mton to 0.84 Mton due to lower production in one industry branch. Import of steam coal was 1.1 Mton (down 0.5 Mton from 1990) since new rules for strategic reserves allowed a reduction of stocks. During the last five years stocks have been reduced by 2 Mtons. Import of metallurgical coal was 1.6 Mton, unchanged from 1990. The report also gives statistics for the coal using plants in Sweden, on coal R and D, and on emission laws for coal firing. (9 tabs., 2 figs.)

  6. Selected problems of coal mining mechanization in the coal industry of Poland

    Antoniak, J; Sikora, W [Politechnika Slaska, Gliwice (Poland)

    1987-01-01

    Discusses conditions for underground coal mining in Poland, types of equipment for coal cutting, mine haulage and strata control and development trends of mining technologies. In 1985, black coal output was 191.6 Mt; 85.3% came from longwall faces mined by sets of mining equipment (coal cutters, chain conveyors and powered supports). The average coal output per longwall face was 881 t/d, output per face mined by sets for mining equipment was 1,134 t/d. In 1985, 653 shearer loaders and 77 coal plows were used in Polish coal mines. Number of shearer loaders is increasing. Shearer loaders with chainless haulage system were safest and most economic. The shearer loaders were equipped with the POLTRAK chainless haulage system developed in Poland. Research programs concentrate on development of new mining equipment for thin seam mining, steep seam mining, longwall mining with hydraulic stowing, efficient strata control by powered or shield supports under conditions of increased stresses or rock burst hazards. 4 refs.

  7. Observer-Based Fuel Control Using Oxygen Measurement. A study based on a first-principles model of a pulverized coal fired Benson Boiler

    Andersen, Palle; Bendtsen, Jan Dimon; Mortensen, Jan Henrik; Just Nielsen, Rene; Soendergaard Pedersen, Tom [Aalborg Univ. (Denmark). Dept. of Control Engineering

    2005-01-01

    This report describes an attempt to improve the existing control of coal mills used at the Danish power plant Nordjyllandsvaerket Unit 3. The coal mills pulverize raw coal to a fine-grained powder, which is injected into the furnace of the power plant. In the furnace the coal is combusted, producing heat, which is used for steam production. With better control of the coal mills, the power plant can be controlled more efficiently during load changes, thus improving the overall availability and efficiency of the plant. One of the main difficulties from a control point of view is that the coal mills are not equipped with sensors that detect how much coal is injected into the furnace. During the project, a fairly detailed, non-linear differential equation model of the furnace and the steam circuit was constructed and validated against data obtained at the plant. It was observed that this model was able to capture most of the important dynamics found in the data. Based on this model, it is possible to extract linearized models in various operating points. The report discusses this approach and illustrates how the model can be linearized and reduced to a lower-order linear model that is valid in the vicinity of an operating point by removing states that have little influence on the overall response. A viable adaptive control strategy would then be to design controllers for each of these simplified linear models, i.e., the control loop that sets references to the coal mills and feedwater, and use the load as a separate input to the control. The control gains should then be scheduled according to the load. However, the variations and uncertainties in the coal mill are not addressed directly in this approach. Another control approach was taken in this project, where a Kalman filter based on measurements of air flow blown into the furnace and the oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate

  8. Short-term dynamics of second-growth mixed mesophytic forest strata in West Virginia

    Cynthia C. Huebner; Steven L. Stephenson; Harold S. Adams; Gary W. Miller

    2007-01-01

    The short-term dynamics of mixed mesophytic forest strata in West Virginia were examined using similarity analysis and linear correlation of shared ordination space. The overstory tree, understory tree, shrub/vine, and herb strata were stable over a six year interval, whereas the tree seedling and sapling strata were unstable. All strata but the shrub/vine and tree...

  9. The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

    Shizhen Tao

    2016-12-01

    Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

  10. Measurement of quantitative species diversity on reclaimed coal mine lands: A brief overview of the Wyoming regulatory proposal

    Vincent, R.B.

    1998-01-01

    The Wyoming Land Quality Division (LQD) Coal Rules and Regulations require mine operators to specify quantitative procedures for evaluating postmining species diversity and composition. Currently, permit commitments range from deferring to commit to a quantitative procedure until some future date to applying various similarity/diversity indices for comparison of reclaimed lands to native vegetation communities. Therefore, the LQD began trying to develop a standardized procedure to evaluate species diversity and composition, while providing operator flexibility. Review of several technical publications on the use of similarity and diversity indices, and other measurement techniques indicate that a consensus has not been reached on which procedure is most appropriate for use on reclaimed mine lands. In addition, implementation of many of the recommended procedures are not practical with regards to staff and data limitations. As a result, the LQD has developed an interim procedure, based on site-specific baseline data, to evaluate postmining species diversity and composition success with respect to bond release requests. This paper reviews many of the recommended procedures, outlines some of the pros and cons, and provides a specific example of how the proposed interim procedure was applied to an actual coal mine permit. Implementation of this or a similar procedure would allow for site-specific standardization of permits and regulatory requirements, thus reducing review time and reducing some of the subjectivity surrounding a component of the Wyoming bond release requirements

  11. Coal 1992

    1992-01-01

    ACR's Coal 1992, the successor to the ACR Coal Marketing Manual, contains a comprehensive set of data on many aspects of the Australian coal industry for several years leading up to 1992. Tables and text give details of coal production and consumption in New South Wales, Queensland and other states. Statistics of the Australian export industry are complemented by those of South Africa, USA, New Zealand, Canada, Indonesia, China, Colombia, Poland and ex-USSR. Also listed are prices of Australian coking and non-coking coal, Australian coal stocks (and those of other major countries), loading port capacities, freight rates and coal quality requirements (analysis of coals by brand and supplier). A listing of Australian coal exporting companies is provided. A description of the spot Coal Screen Dealing System is given. World hard coal imports are listed by country and coal imports by major Asian countries tabulated. A forecast of demand by coal type and country up to the year 2000 is included.

  12. Determination of Uranium and Thorium in Brazilian coals by epithermal neutron activation analysis

    Bernedo, L.F.B.

    1981-08-01

    An experimental technique for the determination of uranium and thorium in coal by epithermal neutron activation was developed and systemized. Seventeen different coal samples, six copper monitors for neutron flux corrections and three NBS standard coal samples were irradiated together in a cadmium cylinder. Uranium and thorium were determined by measuring the 239 N sub(p) and 233 P sub(a) activities respectively, being both produced in (n,γ) reactions and subsequent β - decay. The 239 N sub(p) was measured by counting the 106.4 KeV γ-ray in a LEPS detector and the 233 P sub(a) by counting the 311.8 KeV γ-ray, but in a Ge(Li) detector. A 4096 multichannel analizer and a PDP-11 computer complemented the basic measuring equipment. An average precision of 3% was obtained in the analysis of seventeen coal samples coming from different strata and heights of Charqueadas and Morungava mines in Rio Grande do Sul State. The sensitivity of the method is around 100 ppb. This technique will allow determinations of up to twenty elements, besides uranium and thorium, and it can be applied in routine analysis. (Author) [pt

  13. Geomechanics of subsidence above single and multi-seam coal mining

    A.M. Suchowerska Iwanec

    2016-06-01

    Full Text Available Accurate prediction of surface subsidence due to the extraction of underground coal seams is a significant challenge in geotechnical engineering. This task is further compounded by the growing trend for coal to be extracted from seams either above or below previously extracted coal seams, a practice known as multi-seam mining. In order to accurately predict the subsidence above single and multi-seam longwall panels using numerical methods, constitutive laws need to appropriately represent the mechanical behaviour of coal measure strata. The choice of the most appropriate model is not always straightforward. This paper compares predictions of surface subsidence obtained using the finite element method, considering a range of well-known constitutive models. The results show that more sophisticated and numerically taxing constitutive laws do not necessarily lead to more accurate predictions of subsidence when compared to field measurements. The advantages and limitations of using each particular constitutive law are discussed. A comparison of the numerical predictions and field measurements of surface subsidence is also provided.

  14. Coal pump

    Bonin, John H.; Meyer, John W.; Daniel, Jr., Arnold D.

    1983-01-01

    A device for pressurizing pulverized coal and circulating a carrier gas is disclosed. This device has utility in a coal gasification process and eliminates the need for a separate collection hopper and eliminates the separate compressor.

  15. Hydrogeological evidence of low rock mass permeabilities in ordovician strata: Bruce nuclear site

    Beauheim, R.L.; Roberts, R.M.; Avis, J.D.; Heagle, D.

    2011-01-01

    One of the key attributes contributing to the suitability of the Bruce nuclear site to host a Deep Geologic Repository (DGR) for Low and Intermediate Level Waste (L&ILW) is the low permeability of the Ordovician host rock and of the overlying and underlying strata. The permeability of these rocks is so low that diffusion is a much more significant transport mechanism than advection. Hydrogeological evidence for the low permeability of the Ordovician strata comes from two principal sources, direct and indirect. Direct evidence of low permeability is provided by the hydraulic testing performed in deep boreholes, DGR-2 through DGR-6. Straddle-packer hydraulic testing was performed in 57 Ordovician intervals in these five holes. The testing provided continuous coverage using ~30-m straddle intervals of the Ordovician strata exposed in boreholes DGR-2, DGR-3, DGR-4, and DGR-5, while testing was targeted on discontinuous 10.2-m intervals in DGR-6. The average horizontal hydraulic conductivities of these intervals determined from the tests ranged from 2E-16 to 2E-10 m/s. The Lower Member of the Cobourg Formation, which is the proposed host formation for the DGR, was found to have a horizontal hydraulic conductivity of 4E-15 to 3E-14 m/s. The only horizontal hydraulic conductivity values measured that were greater than 2E-12 m/s are from the Black River Group, located at the base of the Ordovician sedimentary sequence. Indirect evidence of low permeability is provided by the observed distribution of hydraulic heads through the Ordovician sequence. Hydraulic head profiles, defined by hydraulic testing and confirmed by Westbay multilevel monitoring systems, show significant underpressures relative to a density-compensated hydrostatic condition throughout most of the Ordovician strata above the Black River Group, whereas the Black River Group is overpressured. Pressure differences of 1 MPa or more are observed between adjacent intervals in the boreholes. The observed

  16. Conventional approaches for assessment of caving behaviour and support requirement with regard to strata control experiences in longwall workings

    G.S.P. Singh

    2015-06-01

    Full Text Available Effective control of roof strata is very important for trouble free operation and regular face advance in mechanised longwall workings. It is now technically possible to exploit coal seams in difficult geo-mining conditions with the help of newer innovations in longwall face machineries. A reliable assessment of caving behaviour and support capacity requirement helps in selecting supports of adequate capacity and making operational preparedness for timely and confident solution of impending problems. This paper reviews the mechanism of roof caving and the conventional approaches of caving behaviour and support requirement in the context of major strata control experiences gained worldwide. The review shows that a number of approaches are being used for advance prediction of caving behaviour and support capacity requirement in a variety of geo-mining conditions. The theoretical explanation of the mechanism of roof caving and the design function of roof supports have been worked out through staged development of approaches, their evaluation followed by their gradual modification and enrichment of synthesized findings. This process is still continuing with consistently improved understanding through growing field experiences in the larger domain of geo-mining conditions and state-of-art strata analysis and monitoring techniques. These attempts have contributed significantly to improving the level of understanding and reducing the gap of uncertainty in planning and design of longwall operation in a given geo-mining condition.

  17. Sedimentation of the Enan suite of the lower to middle Jurassic and coal reserves of the southeastern margin of the Ordos basin (China)

    Zhang, Y

    1983-01-01

    The studied coal bearing series has a parallel origin. The following facial complexes are isolated in its composition: lakes free of vegetation without coal interlayers; overgrown lakes of their margins which are poor in coals; swampy lakes, whose peat beds formed coal layers of shallow or moderate depth; channel sediments without coal layers and swamps from between channel spaces which created thick coal strata of high quality for which, however, a strong changeability in thickness is intrinsic. The coal strata are normally split towards the central parts of the lake basins and river channels. The coal presence of the suite is reduced along the section which is associated with the replacement of the lake swamp conditions of sedimentation by lake river conditions. A paleotectonic analysis established that the distribution of the zones richest in coal was controlled by consedimentational structural elements.

  18. A study on measures to reduce production cost of long-running collieries and coal mining mechanization

    NONE

    1998-12-01

    The reducing coal market has been enforcing the coal industry to make exceptional rationalization and restructuring efforts since the end of the eighties. To the competition from crude oil and natural gas has been added the growing pressure from rising wages and rising production cost as the working get deeper. To improve the competitive position of the remaining 11 coal mines after the rationalization of the industry, studies to improve mining system have been carried out. This report consists of 3 subjects. 1) Designing of the bord and pillar mining method to extract gently inclined seams of the Dogye coal mine. 2) Mechanization of coal cutting by plough. 3) Achievement of the mechanization of coal mining compared to the previous year. (author). 27 refs.

  19. The evolutionary strata of DARPP-32 tail implicates hierarchical ...

    The evolutionary strata of DARPP-32 tail implicates hierarchical functional expansion in higher vertebrates. CHOONG YONG UNG and TEOW CHONG TEOH. Supplementary data 1. Protein sequences of PPP1R1 family from 39 vertebrate species in FASTA format. Supplementary data 2. Multiple sequence alignment results ...

  20. Coal in the Mediterranean

    Sore, J.C.; Coiffard, J.

    1992-01-01

    Mediterranean countries are not traditionally coal producers. In France, the main mines were located in the North and East, and belonged to the great coal fields of northern Europe. Spain is a modest producer (ten million tonnes), as is Turkey with its three million tonnes. The only way most of these mines can stand up to international competition is by an array of protectionistic measures and subsidies. This state of affairs has marked events of quite another nature, as it relates to energy economics. That is, coal has taken on increasing importance in the energy supplies of all the countries of the Mediterranean zone over the past twenty years. In this article, we set out by describing coke supply for the Mediterranean ensemble, and then go on to analyze the development aspects of coal for electrical production, the future of Mediterranean lignite, and the supply of imported coal. 4 refs., 11 figs., 3 tabs

  1. Study and application of measures for prevention of spontaneous combustion of coal in goaf induced by air leakage

    Liu, Y.; Tang, H.; Zou, S.; Shi, S. [Xiangtan Mining Institute (China)

    1996-12-01

    To prevent spontaneous ignition of coal due to air leakage in the goaf, air stoppings were built periodically in a U-shaped air leakage area based on computer simulation and site experience. The measure had reduced remarkably the quantity and extent of air leakage in the mined-out area and expanded the extent of non-spontaneous combustion area, thus prevented effectively the risk of spontaneous ignition and gas explosion. Application of this method in Mugang Mine of Liuzhi Bureau for more than two years had reduced the economic loss by over 3 million Yuan RMB. This method is characterized by simple operation, low cost, etc. It is suitable for mines in under developed area and mines with complicated conditions which are prone to spontaneous ignition. 5 refs., 3 figs., 1 tab.

  2. Formation and retention of methane in coal

    Hucka, V.J.; Bodily, D.M.; Huang, H.

    1992-05-15

    The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

  3. Measurement and investigation of effects of coal tar pitch fractions in nuclear graphite properties

    Fatemi, K.; Fatoorehchian, S.; Ahari Hashemi, F.; Ahmadi, Sh.

    2003-01-01

    Coal tar pitch has a complex chemical structure. Determination of α, β, γ fractions, is one of the methods to get information about its properties. In graphite fabrication it plays a role as a binder for coke particles. During the thermal treatment it carbonizes and changes to a secondary coke. This has considerable affects on the graphite properties. In this paper, determination of α, β, γ-1 fraction in three different types of pitches have been carried out. Graphite specimens have been fabricated by using these pitches and anisotropy coke in laboratory scale. The graphite properties have been compared with the nuclear graphite prototype. The comparison of the results showed that the density and compression strength are appreciable while the anisotropy factor of properties is about one. The linear thermal expansion in graphite from Iranian pitch had a better, result, where it stands in the nuclear range of usage. As a result, our studies showed that the graphite properties are affected by properties of pitch fractions, where it can be used as a proper sample for the graphite fabrication

  4. Outburst Prevention Technology with Borehole Hydraulic Jet Through Strata in Floor Gateway%底板巷穿层钻孔水力冲孔防突技术

    刘明举; 郭献林; 李波; 王冕

    2011-01-01

    针对新安矿14211运输巷掘进过程中面临的煤与瓦斯突出问题,为了研究和确定适合新安煤田三软煤层赋存特点的水力冲孔工艺和消突评价体系,使其快速消除工作面突出危险性,提高煤巷掘进速度,采用底板巷穿层钻孔水力冲孔防突措施,按照考察出的冲孔影响半径均匀布置钻孔,排出部分煤体和瓦斯,使煤体卸压增透.试验结果表明,底板巷穿层水力冲孔技术较好地适应和利用了三软煤层的赋存特点,消除了工作面的突出危险性,掘进速度也由之前的40 m/月提高到75m/月,提高了87.5%.%According to coal and gas outburst problems occurred in the heading process of the No.14211 transportation gateway in Xin'an Mine, in order to study and set up the borehole hydraulic jet technique and the outburst evaluation system suitable for the three soft seam deposit features in Xin'an Coalfield, to rapidly eliminate the outburst danger of the heading face and to improve the seam gateway heading speed, the outburst prevention measures with borehole hydraulic jet through the strata in the floor gateway were applied.According the investigation of the borehole hydraulic jet influence radius, a layout of the berehole pattern was evenly set up and a partial coal and gas could be discharged.Thus the seam pressure could be released and the permeability of the seam could be improved.The experiment result showed that the borehole hydraulic jet technology passed through strata in the floor gateway would be well suitable for and utilization of the deposit features of the three soft seam and could eliminate the outburst danger of the heading face.Thus the heading speed could be improved from the previous 40 m/month to 75 m/month and the heading efficiency was improved by 87.5%.

  5. Selective coal mining of intercalated lignite deposits

    Zunic, R [Kolubara-Projekt, Lazarevac (Yugoslavia)

    1991-01-01

    Describes selective coal mining in the Tamnava-Istocno Polje coal surface coal mine (Yugoslavia), designed for an annual coal production of 11.4 Mt. Until 1991, this mine exploited one thick lignite seam, without spoil intercalations, using a bucket wheel excavator-conveyor-spreader system both for coal mining and removal of overburden. In the future, several spoil intercalations of up to 1.0 m and thicker will appear with a total volume of 22 million m{sup 3}. These intercalations have to be selectively excavated in order to guarantee the calorific value of coal for the Nikola Tesla power plant. Computer calculations were carried out to determine the decrease in excavator coal production due to selective mining of spoil strata. Calculations found that the annual surface mine capacity will be lower by at most 9%, depending on thickness of spoil intercalations. The useful operation time of excavators will be reduced by 98 hours per year. The planned annual coal production will nevertheless be fulfilled. 3 refs.

  6. Behavior of Mercury Emissions from a Commercial Coal-Fired Utility Boiler: TheRelationship Between Stack Speciation and Near-Field Plume Measurements

    The reduction of divalent gaseous mercury (HgII) to elemental gaseous mercury (Hg0) in a commercial coal-fired power plant (CFPP)exhaust plume was investigated by simultaneous measurement in-stack and in-plume as part of a collaborative study among the U.S....

  7. The flora of Early Permian coal measures from the Parana Basin in Brazil: A review

    Iannuzzi, Roberto

    2010-01-01

    This paper presents an updated overview integrating both previous and newly published data on the most important floras found associated with Early Permian coal seams in the Parana Basin, Brazil. These floras occur within the Rio Bonito Formation and correspond to the Gondwana ''Glossopteris Flora.'' For this review, five floras are selected, in ascending stratigraphic order: the ''Sao Joao do Triunfo,'' ''Figueira,'' ''Quiteria,'' ''Morro do Papaleo'' and ''Irapua Bed'' floras. They are the best-known floras of the basin in terms of taxonomic composition, paleoecology and environments of deposition. An early-mid Sakmarian to earliest Artinskian age is indicated for the Rio Bonito Formation based on absolute radiometric and relative biostratigraphic ages. Integration of available information about the selected floras allows evaluation of taphonomic and paleoecological factors to provide a more comprehensive understanding of the Early Permian floral record in the Parana Basin. The variation observed in both the taxonomic composition of individual floras and in the frequency of occurrence of different plant groups is due to the broad range of environmental/edaphic conditions that prevailed in the many different depositional settings represented in the Rio Bonito Formation. A more precise age determination obtained for the plant-bearing deposits permits the establishment of a more confident correlation between the Early Permian floral succession in the Parana Basin and other Early Permian floral successions in other basins. The Sakmarian global warming favored the appearance of pecopterid and sphenopterid ferns amongst the spore-producing plants, and the glossopterids amongst the pollen-producing plants. (author)

  8. Low level measurements of natural radionuclides in soil samples around a coal-fired power plant

    Rosner, G.; Bunzl, K.; Hoetzl, H.; Winkler, R.

    1984-01-01

    To detect a possible contribution of airborne radioactivity from stack effluents to the soil radioactivity, several radionuclides in the soil around a coal-fired power plant have been determined. A plant situated in a rural region of Bavaria was selected to minimize contributions from other civilisatory sources. The soil sampling network consisted of 5 concentric circles with diameters between 0.4 and 5.2 km around the plant, 16 sampling points being distributed regularly on each circle. Radiochemical analysis techniques for 210 Pb and 210 Po in soil samples of several grams has to be developed. They include a wet dissolution procedure, simultaneous precipitation of lead and polonium as the sulfides, purification via lead sulfate, counting of the lead as the chromate in a low-level beta counter and alpha spectrometric determination of the 210 Po in a gridded ionization chamber. The 238 U, 226 Ra, 232 Th and 40 K were counted by low level gamma spectrometry. Specific activities found were in the range of 0.7 to 2.0 pCi g -1 for 210 Pb and 0.3 to 1.6 pCi g -1 for 226 Ra. The distribution patterns of 210 Po and 210 Pb around the plant were found to be similar. They were different, however, from that of 226 Ra. The highest 210 Pb/ 226 Ra activity ratio was 3.9 at a distance of 0.76 km SSE from the plant. Nevertheless, the evidence is not considered to be sufficient to attribute these observations unambiguously to plant release. (orig.)

  9. Low level measurements of natural radionuclides in soil samples around a coal-fired power plant

    Rosner, G.; Bunzl, K.; Hoetzl, H.; Winkler, R. (Gesellschaft fuer Strahlen- und Umweltforschung m.b.H. Muenchen, Neuherberg (Germany, F.R.). Inst. fuer Strahlenschutz)

    1984-06-15

    To detect a possible contribution of airborne radioactivity from stack effluents to the soil radioactivity, several radionuclides in the soil around a coal-fired power plant have been determined. A plant situated in a rural region of Bavaria was selected to minimize contributions from other civilisatory sources. The soil sampling network consisted of 5 concentric circles with diameters between 0.4 and 5.2 km around the plant, 16 sampling points being distributed regularly on each circle. Radiochemical analysis techniques for /sup 210/Pb and /sup 210/Po in soil samples of several grams has to be developed. They include a wet dissolution procedure, simultaneous precipitation of lead and polonium as the sulfides, purification via lead sulfate, counting of the lead as the chromate in a low-level beta counter and alpha spectrometric determination of the /sup 210/Po in a gridded ionization chamber. The /sup 238/U, /sup 226/Ra, /sup 232/Th and /sup 40/K were counted by low level gamma spectrometry. Specific activities found were in the range of 0.7 to 2.0 pCi g/sup -1/ for /sup 210/Pb and 0.3 to 1.6 pCi g/sup -1/ for /sup 226/Ra. The distribution patterns of /sup 210/Po and /sup 210/Pb around the plant were found to be similar. They were different, however, from that of /sup 226/Ra. The highest /sup 210/Pb//sup 226/Ra activity ratio was 3.9 at a distance of 0.76 km SSE from the plant. Nevertheless, the evidence is not considered to be sufficient to attribute these observations unambiguously to plant release.

  10. Measurement and modeling of advanced coal conversion processes. Twenty-first quarterly report, October 1, 1991--December 31, 1991

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. [Advanced Fuel Research, Inc., East Hartford, CT (United States); Smoot, L.D.; Brewster, B.S. [Brigham Young Univ., Provo, UT (United States)

    1991-12-31

    The objective of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines.

  11. Measurement and modeling of advanced coal conversion processes. 19th quarterly report, April 1, 1991--June 30, 1991

    Solomon, P.R.; Serio, M.A.; Hamblen, D.G. [Advanced Fuel Research, Inc., East Hartford, CT (United States); Smoot, L.D.; Brewster, B.S. [Brigham Young Univ., Provo, UT (United States)

    1991-09-25

    The objectives of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines. (VC)

  12. Immersion freezing induced by different kinds of coal fly ash: Comparing particle generation methods and measurement techniques

    Grawe, Sarah; Augustin-Bauditz, Stefanie; Clemen, Hans-Christian; Eriksen-Hammer, Stine; Lubitz, Jasmin; Schneider, Johannes; Stratmann, Frank; Wex, Heike

    2017-04-01

    To date, a lot of effort has been put into the identification and characterization of atmospheric ice nucleating particles (INPs), which may influence both weather and climate. The majority of studies focuses on INPs from natural origin such as biological particles or mineral dust particles (Hoose and Möhler 2012, Murray et al. 2012). Combustion ashes, being possible sources of anthropogenic INPs, have rarely been investigated in the past. Ash particles may be emitted into the atmosphere either by the action of wind from ash deposits on the ground (bottom ash), or during the combustion process (fly ash). Two recent studies (Umo et al., 2015; Grawe et al., 2016) identified fly ash from coal combustion as the most efficient of the investigated samples (including also bottom ashes from wood and coal combustion). These results motivate the here presented study in which we investigated the immersion freezing behavior of four coal fly ash samples taken from the filters of different coal-fired power plants in Germany. A combination of two instruments was used to capture the temperature range from 0 °C to the homogeneous freezing limit at around -38 °C. Firstly, the new Leipzig Ice Nucleation Array (LINA) was used, where droplets from an ash-water suspension are pipetted onto a cooled plate. Secondly, we used the Leipzig Aerosol Cloud Interaction Simulator (LACIS; Hartmann et al., 2011), a laminar flow tube in which every droplet contains a single size-segregated ash particle. Here, it was possible to study the effect of different kinds of particle generation, i.e., atomization of an ash-water suspension, and aerosolization of dry ash material. The composition of the ash particles was investigated by means of single particle aerosol mass spectrometry and particles were sampled on filters for environmental scanning electron microscope analysis. Our measurements show that all four fly ash samples feature a similar immersion freezing behavior (ice fractions vary by a

  13. Extreme coal handling

    Bradbury, S; Homleid, D. [Air Control Science Inc. (United States)

    2004-04-01

    Within the journals 'Focus on O & M' is a short article describing modifications to coal handling systems at Eielson Air Force Base near Fairbanks, Alaska, which is supplied with power and heat from a subbituminous coal-fired central plant. Measures to reduce dust include addition of an enclosed recirculation chamber at each transfer point and new chute designs to reduce coal velocity, turbulence, and induced air. The modifications were developed by Air Control Science (ACS). 7 figs., 1 tab.

  14. Fiscal 1996 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system`; 1996 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho

    NONE

    1997-03-01

    Oil demand is expected to substantially grow in the future, and the use of oil with combustibles such as hull, baggase and waste is considered from an effective use of energy. A regional model survey was conducted as measures to reduce environmental loads where the fuel mixing combustion with coal and other energy is made the core. The domestic production amount of hull is 2.4-3.0 tons/year, which have a heating value of 3,500 kcal/kg. If hull can be formed into the one storable for a the long term (the one mixed with low grade coal, etc.), it can be a fuel for stable supply. Bagasse is produced 100 million tons/year, which have a heating value of 2,500 kcal/kg. Among wastes, waste tire, plastics, waste, sludge, etc. have a lot of problems in terms of price and environment, but each of them has a heating value during 3,000-10,000 kcal/kg. As to the coal combustion, the pollutional regulation on it is strict, and much higher processing technology is needed. The technology of coal fuel mixing combustion with other energy has not risen higher than the developmental level. Though the technology is a little bit higher in price than the coal fuel single combustion, it is viable. 38 refs., 32 figs., 65 tabs.

  15. Clustering network layers with the strata multilayer stochastic block model.

    Stanley, Natalie; Shai, Saray; Taylor, Dane; Mucha, Peter J

    2016-01-01

    Multilayer networks are a useful data structure for simultaneously capturing multiple types of relationships between a set of nodes. In such networks, each relational definition gives rise to a layer. While each layer provides its own set of information, community structure across layers can be collectively utilized to discover and quantify underlying relational patterns between nodes. To concisely extract information from a multilayer network, we propose to identify and combine sets of layers with meaningful similarities in community structure. In this paper, we describe the "strata multilayer stochastic block model" (sMLSBM), a probabilistic model for multilayer community structure. The central extension of the model is that there exist groups of layers, called "strata", which are defined such that all layers in a given stratum have community structure described by a common stochastic block model (SBM). That is, layers in a stratum exhibit similar node-to-community assignments and SBM probability parameters. Fitting the sMLSBM to a multilayer network provides a joint clustering that yields node-to-community and layer-to-stratum assignments, which cooperatively aid one another during inference. We describe an algorithm for separating layers into their appropriate strata and an inference technique for estimating the SBM parameters for each stratum. We demonstrate our method using synthetic networks and a multilayer network inferred from data collected in the Human Microbiome Project.

  16. Australian coal

    1985-11-01

    Total export shipments of coal in Australia in the year ending June 30 1985 reached a record of 83.8 Mt. The export trade is expected to bring in an income of 4 billion Australian dollars in the current year making coal Australia's biggest revenue-earning export commodity. This article presents a brief overview of the Australian coal industry with production and export statistics and information on major open pit and underground mines.

  17. Suspension-firing of wood with coal ash addition: Probe measurements of ash deposit build-up at Avedøre Power Plant (AVV2)

    Shafique Bashir, Muhammad; Jensen, Peter Arendt; Jappe Frandsen, Flemming

    This report is about full-scale probe measurements of deposit build-up and removal conducted at the Avedøreværket Unit 2, a 800 MWth suspension boiler, firing wood and natural gas with the addition of coal ash. Coal ash was used as an additive to capture potassium (K) from wood-firing. Investigat...... to the gas phase as HCl(g). Effect of boiler operational parameters on gas emissions has also been investigated.......This report is about full-scale probe measurements of deposit build-up and removal conducted at the Avedøreværket Unit 2, a 800 MWth suspension boiler, firing wood and natural gas with the addition of coal ash. Coal ash was used as an additive to capture potassium (K) from wood...... and boiler load on ash deposition propensity was investigated. Results of ash deposition propensity showed increasing trend with increasing flue gas temperature. Video monitoring revealed that the deposits formed were not sticky and could be easily removed, and even at very high flue gas temperatures (> 1350...

  18. Coal - 96

    Sparre, C.

    1996-09-01

    The report deals mainly with coal consumption, but also gives some information about technology, environmental aspects and markets. Data have been collected by questionnaires or via telephone. The use of steam coal for heating was 0.8 Mtons (down 20% from 1994). Cogeneration plants were the main users. Taxes and environmental reasons cause a reduction of the coal use that will probably continue the next years. Use of steam coal in industry has been constant at a level of 0.7 Mtons. The import of metallurgical coal rests constant at a level of 1.6 Mtons. 1.2 Mtons of coke was produced, and 0.3 Mtons imported. The PFBC-plant at Vaertan, Stockholm used 0.13 Mtons of coal, while some coal fired power plants have been converted to peat and wood fuels. The average price of steam coal imported to Sweden in 1995 was 333 SEK/ton, 6% higher than in 1994. The contract prices for delivery 1996 are about the same as at the end of 1995. All cogeneration plants have some sort of SO 2 removal system, mostly wet-dry. The largest plant, at Vaesteraas, has recently invested in a SCR system for NO x removal. Most other plants are using low NO x burners or SNCR systems, based on ammonia or urea, which reduce the emissions 50 - 70%. Some statistic about the world coal market is also given in the report

  19. Venezuelan coal

    Vazquez, L.U.

    1991-01-01

    The existence of coal deposits in Venezuela has been known since the early nineteenth century, when the Naricual Mines were discovered in the State of Anzoategui Eastern Venezuela. Through the years the Venezuelan coal business had its ups and downs, but it was not until 1988 that we could properly say that our coal began to play a role in the international market. This paper reports that it is only now, in the nineties, that Venezuelan coal projects have come under a planning, promotional and developmental policy preparing the ground for the great projects Venezuela will have in the not-too-distant future

  20. USGS assessment of undiscovered oil and gas resources in Paleogene strata of the U.S. Gulf of Mexico coastal plain and state waters

    Warwick, Peter D.; Coleman, James; Hackley, Paul C.; Hayba, Daniel O.; Karlsen, Alexander W.; Rowan, Elisabeth L.; Swanson, Sharon M.; Kennan, Lorcan; Pindell, James; Rosen, Norman C.

    2007-01-01

    This report presents a review of the U.S. Geological Survey (USGS) 2007 assessment of the undiscovered oil and gas resources in Paleogene strata underlying the U.S. Gulf of Mexico Coastal Plain and state waters. Geochemical, geologic, geophysical, thermal maturation, burial history, and paleontologic studies have been combined with regional cross sections and data from previous USGS petroleum assessments have helped to define the major petroleum systems and assessment units. Accumulations of both conventional oil and gas and continuous coal-bed gas within these petroleum systems have been digitally mapped and evaluated, and undiscovered resources have been assessed following USGS methodology.The primary source intervals for oil and gas in Paleogene (and Cenozoic) reservoirs are coal and shale rich in organic matter within the Wilcox Group (Paleocene-Eocene) and Sparta Formation of the Claiborne Group (Eocene); in addition, Cretaceous and Jurassic source rocks probably have contributed substantial petroleum to Paleogene (and Cenozoic) reservoirs.For the purposes of the assessment, Paleogene strata have divided into the following four stratigraphic study intervals: (1) Wilcox Group (including the Midway Group and the basal Carrizo Sand of the Claiborne Group; Paleocene-Eocene); (2) Claiborne Group (Eocene); (3) Jackson and Vicksburg Groups (Eocene-Oligocene); and (4) the Frio-Anahuac Formations (Oligocene). Recent discoveries of coal-bed gas in Paleocene strata confirm a new petroleum system that was not recognized in previous USGS assessments. In total, 26 conventional Paleogene assessment units are defined. In addition, four Cretaceous-Paleogene continuous (coal-bed gas) assessment units are included in this report. Initial results of the assessment will be released as USGS Fact Sheets (not available at the time of this writing).Comprehensive reports for each assessment unit are planned to be released via the internet and distributed on CD-ROMs within the next year.

  1. Measurement of batter movements in brown coal open cuts - results of a research project

    Nehring, H

    1984-05-01

    In the course of a research project sponsored by the State of North Rhine-Westphalia the mine surveying methods used when measuring deformation on open cut batters were further developed, by taking into account the special conditions prevailing in open cuts, to such an extent that the essential monitoring of soil movements can be carried out reliably and promptly. As an integral part of an optimised, accurate geodetic measurement of points, the direct measurement of longitude across the open cut was introduced as a rapid measuring method. The aerophotogrammetric measurement of points is practically as accurate as terrestrial surveying. The author describes the prototype of an automatically operated instrument system for the monitoring of points. In conclusion he also stresses that the first promising advance has already been made as regards the sufficiently accurate monitoring of rock movements in boreholes.

  2. Seal evaluation and confinement screening criteria for beneficial carbon dioxide storage with enhanced coal bed methane recovery in the Pocahontas Basin, Virginia

    Grimm, R.P.; Eriksson, K.A.; Ripepi, N.; Eble, C.; Greb, S.F.

    2012-01-01

    The geological storage of carbon dioxide in Appalachian basin coal seams is one possible sink for sequestration of greenhouse gases, with the added benefit of enhanced-coal bed methane (ECBM) recovery. The Pocahontas Basin (part of the central Appalachian Basin) of southwestern Virginia is a major coal bed methane (CBM) province with production mostly from coal beds in the Lower Pennsylvanian Pocahontas and New River formations. As part of the Southeast Regional Carbon Sequestration Partnership's Phase II research program, a CO 2-injection demonstration well was installed into Lower Pennsylvanian coal bed-methane producing strata in southwest Virginia. Samples of siliciclastic lithologies above coal beds in this Oakwood Field well, and from several other cores in the Nora Field were taken to establish a baseline of the basic confinement properties of overlying strata to test seal competency at local and regional scales.Strata above CBM-producing coal beds in the Pocahontas and New River formations consist of dark-gray shales; silty gray shales; heterolithic siltstones, sandstones, and shales; lithic sandstones, and quartzose sandstones. Standard measurements of porosity, permeability and petrography were used to evaluate potential leakage hazards and any possible secondary storage potential for typical lithologies. Both lithic- and quartz-rich sandstones exhibit only minor porosity, with generally low permeability (Member. Analyses of 1500 geophysical logs in southwest Virginia indicate that this unit is moderately thick (>50ft, 15m), laterally continuous (>3000km 2), and a homogenous shale, which coarsens upward into siltstone and sandstone, or is truncated by sandstone. Calculations from two mercury injection capillary porosimetry tests of the shale indicate that a displacement entry pressure of 207psi (1427kPa) would generate an estimated seal capacity of 1365ft (416m) of CO 2 before buoyant leakage. Scanning electron microscopy indicates a microfabric of narrow

  3. Geospatial Database for Strata Objects Based on Land Administration Domain Model (ladm)

    Nasorudin, N. N.; Hassan, M. I.; Zulkifli, N. A.; Rahman, A. Abdul

    2016-09-01

    Recently in our country, the construction of buildings become more complex and it seems that strata objects database becomes more important in registering the real world as people now own and use multilevel of spaces. Furthermore, strata title was increasingly important and need to be well-managed. LADM is a standard model for land administration and it allows integrated 2D and 3D representation of spatial units. LADM also known as ISO 19152. The aim of this paper is to develop a strata objects database using LADM. This paper discusses the current 2D geospatial database and needs for 3D geospatial database in future. This paper also attempts to develop a strata objects database using a standard data model (LADM) and to analyze the developed strata objects database using LADM data model. The current cadastre system in Malaysia includes the strata title is discussed in this paper. The problems in the 2D geospatial database were listed and the needs for 3D geospatial database in future also is discussed. The processes to design a strata objects database are conceptual, logical and physical database design. The strata objects database will allow us to find the information on both non-spatial and spatial strata title information thus shows the location of the strata unit. This development of strata objects database may help to handle the strata title and information.

  4. 76 FR 71082 - Strata Energy, Inc., Ross Uranium Recovery Project; New Source Material License Application...

    2011-11-16

    ... NUCLEAR REGULATORY COMMISSION [Docket No. 40-9091; NRC-2011-0148] Strata Energy, Inc., Ross Uranium Recovery Project; New Source Material License Application; Notice of Intent To Prepare a... intent to prepare a supplemental environmental impact statement. SUMMARY: Strata Energy, Inc. (Strata...

  5. Geodynamic methods for assessing methane distribution in bituminous coal deposits and measures to intensify methane fluxes during mine gas drainage

    Е. В. Гончаров

    2016-12-01

    Full Text Available This paper explores states of methane within the coal bearing stratum and shows heavy dependency of the intrastratal gas migration on the forms of porous space and petrographic properties of coal. The adsorbed methane is found to be predominant in the coal of Kuznetsk Basin. Different forms of coal diffusion and filtration are described revealing their dependency on geological and thermodynamic conditions. The paper provides justification for the primary focus on geodynamic processes when designing gas drainage systems and applicability of morphometric methods and remote sensing data for their identification. The significance of researches into the processes activating exothermic reactions resulting in methane transition to free state is explained. The paper presents the results of using seismic-acoustic stimulation techniques as one of the practical approaches to addressing this issue. Results of successful industrial testing have been compared with the results of numerical modelling of stress-strain state, which can also be managed through seismic-acoustic stimulation.

  6. Coal summit II

    1983-01-01

    Various papers were presented on world coal trade. Papers include: Poland as a producer and exporter of coal; the dynamics of world coal trade; Cerrejon coal production perspectives; present state of the Australian coal industry; present state of the EC coal market and future prospects; prospects of US coal exports to Europe; forecast of Italian coal supply and demand through 1990; statistics from coal transportation outlook; status of world coal ports.

  7. Special emission measurements on Riley Stoker's advanced CFB pilot facility co-firing non-recyclable de-inking paper fiber and high sulfur eastern bituminous coal

    Dixit, V.B.; Mongeon, R.K.; Reicker, E.L.

    1993-01-01

    Riley Stoker has developed advanced industrial CFB designs that utilize eastern bituminous coals as fuel, and have the potential to use coal in combination with other fuels. Various fiber waste streams in paper recycling processes have sufficient carbonaceous content to be considered as possible sources of such fuels that could fire FBC combustors. The American Paper Institute estimates that by the mid-1990's more than 40% of the waste paper will be recycled, reaching much higher numbers by the year 2000. To evaluate the effectiveness of co-firing such fuels, a test program was conducted on Riley's pilot-scale circulating fluidized bed test facility. A de-inked newsprint derived fiber waste was successfully co-fired with high sulfur coal. The waste fiber material containing approximately 50% moisture had a heating value of 3500 Btu/lb. The coal was strip-mined and contained a lot of clay and excessive quantities of fines making it difficult to burn in conventional boilers. Tests were also conducted with a combination fuel consisting of coal, fiber waste and a high carbon fly ash. In addition to obtaining performance data on combustion efficiency, sulfur capture, and NO x emissions, special emission measurements were also made to quantify the organics, trace metals and hydrochloric acid levels in the flue gas. The co-firing tests achieved a maximum combustion efficiency of 98% and sulfur capture of 90%. The effect of Ca/S mole ratio and temperature is discussed. Although there are no formal regulations in place for FBC systems regarding special emissions, the levels measured were far below the allowable limits for waste incinerators. Materials handling experience on the pilot facility relating to co-firing is also discussed. This is done to identify special considerations for designing commercial facilities. A brief overview of the de-inking waste fiber combustion market is also presented

  8. Measurement of gas species, temperatures, coal burnout, and wall heat fluxes in a 200 MWe lignite-fired boiler with different overfire air damper openings

    Jianping Jing; Zhengqi Li; Guangkui Liu; Zhichao Chen; Chunlong Liu [Harbin Institute of Technology, Harbin (China). School of Energy Science and Engineering

    2009-07-15

    Measurements were performed on a 200 MWe, wall-fired, lignite utility boiler. For different overfire air (OFA) damper openings, the gas temperature, gas species concentration, coal burnout, release rates of components (C, H, and N), furnace temperature, and heat flux and boiler efficiency were measured. Cold air experiments for a single burner were conducted in the laboratory. The double-swirl flow pulverized-coal burner has two ring recirculation zones starting in the secondary air region in the burner. As the secondary air flow increases, the axial velocity of air flow increases, the maxima of radial velocity, tangential velocity and turbulence intensity all increase, and the swirl intensity of air flow and the size of recirculation zones increase slightly. In the central region of the burner, as the OFA damper opening widens, the gas temperature and CO concentration increase, while the O{sub 2} concentration, NOx concentration, coal burnout, and release rates of components (C, H, and N) decrease, and coal particles ignite earlier. In the secondary air region of the burner, the O{sub 2} concentration, NOx concentration, coal burnout, and release rates of components (C, H, and N) decrease, and the gas temperature and CO concentration vary slightly. In the sidewall region, the gas temperature, O{sub 2} concentration, and NOx concentration decrease, while the CO concentration increases and the gas temperature varies slightly. The furnace temperature and heat flux in the main burning region decrease appreciably, but increase slightly in the burnout region. The NOx emission decreases from 1203.6 mg/m{sup 3} (6% O{sub 2}) for a damper opening of 0% to 511.7 mg/m{sup 3} (6% O{sub 2}) for a damper opening of 80% and the boiler efficiency decreases from 92.59 to 91.9%. 15 refs., 17 figs., 3 tabs.

  9. Investigations of coal ignition in a short-range flame burner using optical measuring systems; Untersuchungen zur Kohlezuendung am Flachflammenbrenner unter Verwendung optischer Messtechnik

    Hackert, G.; Kremer, H.; Wirtz, S. [Bochum Univ. (Germany). Lehrstuhl fuer Energieanlagentechnik

    1999-09-01

    The short-range flame burner and the KOALA reactor of DMT are experimental facilities for realistic simulation of coal conversion processes at high temperatures and pressures in atmospheric conditions. The TOSCA system enable measurements of temperatures, sizes, shapes and velocities of the fuel particles, which serve as a basis for a three-dimensional simulation model of coal combustion. In the future, further parameter studies will deepen the present knowledge of coal dust combustion under pressure and enable optimisation of the numerical models for simulation of industrial-scale systems for coal dust combustion under pressure. [Deutsch] Mit dem Flachflammenbrenner und dem KOALA-Reaktor der DMT stehen Versuchsapparaturen zur Verfuegung, mit deren Hilfe die Kohleumwandlungsprozesse bei hohen Temperaturen unter Druck und unter atmosphaerischen Bedingungen realistisch wiedergegeben werden. Das TOSCA-System erlaubt dabei die Bestimmung von Temperaturen, Groessen, Formen und Geschwindigkeiten der Brennstoffpartikel. Diese Daten liefern die Grundlage fuer die Erstellung eines dreidimensionalen Simulationsmodells zur Modellierung der Kohleverbrennung. In Zukunft werden weitere Parameterstudien das Verstaendnis der Kohlenstaubdruckverbrennung vertiefen und ein Optimierung der numerischen Modelle ermoeglichen, so dass die Simulation grosstechnischer Kohlenstaubdruckverbrennungsanlagen realisiert werden kann. (orig.)

  10. Method for assessing coal-floor water-inrush risk based on the variable-weight model and unascertained measure theory

    Wu, Qiang; Zhao, Dekang; Wang, Yang; Shen, Jianjun; Mu, Wenping; Liu, Honglei

    2017-11-01

    Water inrush from coal-seam floors greatly threatens mining safety in North China and is a complex process controlled by multiple factors. This study presents a mathematical assessment system for coal-floor water-inrush risk based on the variable-weight model (VWM) and unascertained measure theory (UMT). In contrast to the traditional constant-weight model (CWM), which assigns a fixed weight to each factor, the VWM varies with the factor-state value. The UMT employs the confidence principle, which is more effective in ordered partition problems than the maximum membership principle adopted in the former mathematical theory. The method is applied to the Datang Tashan Coal Mine in North China. First, eight main controlling factors are selected to construct the comprehensive evaluation index system. Subsequently, an incentive-penalty variable-weight model is built to calculate the variable weights of each factor. Then, the VWM-UMT model is established using the quantitative risk-grade divide of each factor according to the UMT. On this basis, the risk of coal-floor water inrush in Tashan Mine No. 8 is divided into five grades. For comparison, the CWM is also adopted for the risk assessment, and a differences distribution map is obtained between the two methods. Finally, the verification of water-inrush points indicates that the VWM-UMT model is powerful and more feasible and reasonable. The model has great potential and practical significance in future engineering applications.

  11. Measurements of Gasification Characteristics of Coal and Char in CO2-Rich Gas Flow by TG-DTA

    Zhigang Li

    2013-01-01

    Full Text Available Pyrolysis, combustion, and gasification properties of pulverized coal and char in CO2-rich gas flow were investigated by using gravimetric-differential thermal analysis (TG-DTA with changing O2%, heating temperature gradient, and flow rate of CO2-rich gases provided. Together with TG-DTA, flue gas generated from the heated coal, such as CO, CO2, and hydrocarbons (HCs, was analyzed simultaneously on the heating process. The optimum O2% in CO2-rich gas for combustion and gasification of coal or char was discussed by analyzing flue gas with changing O2 from 0 to 5%. The experimental results indicate that O2% has an especially large effect on carbon oxidation at temperature less than 1100°C, and lower O2 concentration promotes gasification reaction by producing CO gas over 1100°C in temperature. The TG-DTA results with gas analyses have presented basic reference data that show the effects of O2 concentration and heating rate on coal physical and chemical behaviors for the expected technologies on coal gasification in CO2-rich gas and oxygen combustion and underground coal gasification.

  12. Evaluation of occupational exposure in a underground coal mine by environmental measures of 222Rn and in vivo measurements of 210Pb in bones

    Dantas, A.L.A.; Veiga, L.H.S.; Dantas, B.M.; Melo, V.P.

    2005-01-01

    A radiological survey performed in an underground coal mining in the State of Parana, southern Brazil, has indicated the occurrence of high levels of concentration of radon and its decay products. The levels of 222 Rn concentration measured in the basement of this mine, in the period from 1999 to 2003 ranged from 2000 to 7000 Bq m -3 . It is estimated, for these workers, an average annual exposure of 2.1 WLM ranging from 0.2 to 7.2 WLM. A retrospective mortality study conducted with 2856 miners of this mining indicated a risk of lung cancer mortality greater than the one expected for the male population of the State. In this study the cumulative exposure to radon cannot be estimated since there was no radon measures in other periods. In this way, the cumulative exposure can be evaluated by through 210 Pb activities monitored in the skeleton. The measures of 210 Pb in skeleton ranged from 83 to 164 Bq, indicating that these workers were significantly exposed to 222 Rn. These results show that cumulative exposure to radon has been higher than estimated based on recent measures of the activity concentration of radon in the workplace and is compatible with the risk determined in the epidemiological study

  13. Tertiary strata and hydro-geological conditions, figures for movement of groundwater above Gorleben

    Giesel, W.

    1984-01-01

    In order to determine the movement of groundwater, a geo-hydraulic model is used. From the results, one can deduce that the movement of groundwater reaches down to closely above the salt strata, and that groundwater from this depth can flow back to the biosphere after one to several 1000 years. The highly saline water in the depth of the trough is treated separately. Geo-physical borehole measurements have shown that the salty groundwater in the trough moves northwards. 10 3 to 10 4 m 3 of salt/annum are transported away from the trough. (DG) [de

  14. Influences of volcanism on coal quality - Examples from the western United States

    Hildebrand, R.T.; Affolter, R.H.

    1986-01-01

    Several small Tertiary coal deposits in Idaho, Nevada, and Washington formed in fresh-water basins located near active continental (salic) volcanic centers. Metastable glassy material (tephra) ejected during volcanic eruptions was introduced into the coal-forming environment of these basins as ash falls. This tephra contributed to the high ash content of many of the coal beds, formed laterally persistent partings (''tonsteins'') in the coal, and constitutes a large part of the strata enclosing the deposits. In order to study the possible relationships between the presence of tephra and coal quality, chemical data for 65 coal samples from 12 of these deposits were compiled and statistically analyzed. The results indicate that, in addition to the high ash content, coal from Tertiary deposits containing appreciable amounts of tephra generally is enriched in many elements compared to 460 coal samples from 11 deposits of similar ages remote from volcanic activity

  15. Earth Conductivity Estimation from Through-the-Earth Measurements of 94 Coal Mines Using Different Electromagnetic Models.

    Yan, Lincan; Waynert, Joseph; Sunderman, Carl

    2014-10-01

    Through-the-Earth (TTE) communication systems require minimal infrastructure to operate. Hence, they are assumed to be more survivable and more conventional than other underground mine communications systems. This survivability is a major advantage for TTE systems. In 2006, Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which requires all underground coal mines to install wireless communications systems. The intent behind this mandate is for trapped miners to be able to communicate with surface personnel after a major accident-hence, the interest in TTE communications. To determine the likelihood of establishing a TTE communication link, it would be ideal to be able to predict the apparent conductivity of the overburden above underground mines. In this paper, all 94 mine TTE measurement data collected by Bureau of Mines in the 1970s and early 1980s, are analyzed for the first time to determine the apparent conductivity of the overburden based on three different models: a homogenous half-space model, a thin sheet model, and an attenuation factor or Q-factor model. A statistical formula is proposed to estimate the apparent earth conductivity for a specific mine based on the TTE modeling results given the mine depth and signal frequency.

  16. Comparing and assessing different measurement techniques for mercury in coal systhesis gas

    Maxwell, D.P.; Richardson, C.F. [Radian Corporation, Austin, TX (United States)

    1995-11-01

    Three mercury measurement techniques were performed on synthesis gas streams before and after an amine-based sulfur removal system. The syngas was sampled using (1) gas impingers containing a nitric acid-hydrogen peroxide solution, (2) coconut-based charcoal sorbent, and (3) an on-line atomic absorption spectrophotometer equipped with a gold amalgamation trap and cold vapor cell. Various impinger solutions were applied upstream of the gold amalgamation trap to remove hydrogen sulfide and isolate oxidized and elemental species of mercury. The results from these three techniques are compared to provide an assessment of these measurement techniques in reducing gas atmospheres.

  17. Survey of horizontal stresses in coal mines from available measurements and mapping.

    Frith, R

    2002-09-01

    Full Text Available of work for the project was outlined in the proposal submitted to SIMRAC in mid-2000 and is summarised as follows: (i) to undertake a peer review of available in-situ stress measurements relating to the Witbank and Highveld coalfields in South Africa... OF HORIZONTAL STRESS IN THE WITBANK AND HIGHVELD COALFIELDS 21 4.1 Is Horizontal Stress at Work in Roadway Roof Behaviour? 21 4.2 Summary of Measured Horizontal Stresses 24 4.3 Proposed Model for the Origin of Horizontal Stress Within the Coalfields 27 4...

  18. Results of integrated geophysical measurements on a landslide endangered brown coal dump

    Militzer, H; Lindner, H; Kaeppler, R

    1984-01-01

    The measurements revealed occurrence of geophysical anomalies across artificial soils with low content of cohesive material. The proven anomalies varied with time with regard to their magnitude and position. Possible relations between the temporal variations of the geophysical fields and a landslide on the boundary of the object are discussed.

  19. Mercury Emission Measurement in Coal-Fired Boilers by Continuous Mercury Monitor and Ontario Hydro Method

    Zhu, Yanqun; Zhou, Jinsong; He, Sheng; Cai, Xiaoshu; Hu, Changxin; Zheng, Jianming; Zhang, Le; Luo, Zhongyang; Cen, Kefa

    2007-06-01

    The mercury emission control approach attaches more importance. The accurate measurement of mercury speciation is a first step. Because OH method (accepted method) can't provide the real-time data and 2-week time for results attained, it's high time to seek on line mercury continuous emission monitors(Hg-CEM). Firstly, the gaseous elemental and oxidized mercury were conducted to measure using OH and CEM method under normal operation conditions of PC boiler after ESP, the results between two methods show good consistency. Secondly, through ESP, gaseous oxidized mercury decrease a little and particulate mercury reduce a little bit, but the elemental mercury is just the opposite. Besides, the WFGD system achieved to gaseous oxidized mercury removal of 53.4%, gaseous overall mercury and elemental mercury are 37.1% and 22.1%, respectively.

  20. International Coal Report's coal year 1991

    McCloskey, G [ed.

    1991-05-31

    Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

  1. Consumption Behavior of Middle Strata in Times of Economic Crisis

    Svetlana V. Mareeva

    2017-03-01

    Full Text Available Based on the data of national representative surveys carried out by IS RAS in 2014-2016, the author presents analysis of consumption specifics in middle-income groups in times of current economic crisis. It is shown that although in modern Russian society middle income groups make up the majority of population, they cannot be directly correlated with the middle class defined in class theory framework. Middle-income groups are heterogeneous in different aspects, including their consumption specifics. Their standard of living remains quite modest, although it is significantly higher than the “survival standard”. New economic conditions led to widespread economy practices among them - primarily on consumption, followed by economy on hobbies and vacations. Economy practices also seriously affected middle-income strata investments in human capital – usage of paid educational and health services (this type of economy was more widespread among lower middle-income group than higher. Although representatives of the middle-income strata are quite actively using paid medical services (and relatively rarely – paid educational services, the reason for this more often lies in inaccessibility of free analogues rather than in search for the higher quality. Process of durables renewal in middle strata during the crisis was not as active, but their standard set of durable goods still widened over the past two years - primarily due to the relatively complex technological durables that they are gradually transferred from the category of innovation goods to the extended standard. In this regard, the upper middle income group successfully performs the function of the innovative consumer.

  2. Mineralogical and geological study of fault rocks and associated strata

    Kim, Jeon Jin; Jeong, Gyo Cheol; Bae, Doo Won; Park, Seong Min; Kim, Jun Yeong

    2007-01-01

    Mineralogical characterizations of fault clay and associated strata in fault zone with field study and analytical methods. Mineral composition and color of fault clay and rock occur in fracture zone different from bed rocks. Fault clay mainly composed of smectite with minor zeolite such as laumontite and stilbite, and halloysite, illite, Illite and halloysite grow on the surface of smectite, and laumontite and stilbite result from precipitation or alteration of Ca rich bed rock. The result of mineralogical study at Ipsil, Wangsan, Gaegok, Yugyeori, Gacheon in Gyeongju area, the detail research of microstructure in the fault clay making it possible for prediction to age of fault activity

  3. Mineralogical and geological study of fault rocks and associated strata

    Kim, Jeon Jin; Jeong, Gyo Cheol; Bae, Doo Won; Park, Seong Min; Kim, Jun Yeong [Andong Univ., Andong (Korea, Republic of)

    2007-01-15

    Mineralogical characterizations of fault clay and associated strata in fault zone with field study and analytical methods. Mineral composition and color of fault clay and rock occur in fracture zone different from bed rocks. Fault clay mainly composed of smectite with minor zeolite such as laumontite and stilbite, and halloysite, illite, Illite and halloysite grow on the surface of smectite, and laumontite and stilbite result from precipitation or alteration of Ca rich bed rock. The result of mineralogical study at Ipsil, Wangsan, Gaegok, Yugyeori, Gacheon in Gyeongju area, the detail research of microstructure in the fault clay making it possible for prediction to age of fault activity.

  4. The Strata-l Experiment on Microgravity Regolith Segregation

    Fries, M.; Abell, P.; Brisset, J.; Britt, D.; Colwell, J.; Durda, D.; Dove, A.; Graham, L.; Hartzell, C.; John, K.; hide

    2016-01-01

    The Strata-1 experiment studies the segregation of small-body regolith through long-duration exposure of simulant materials to the microgravity environment on the International Space Station (ISS). Many asteroids feature low bulk densities, which implies high values of porosity and a mechanical structure composed of loosely bound particles, (i.e. the "rubble pile" model), a prime example of a granular medium. Even the higher-density, mechanically coherent asteroids feature a significant surface layer of loose regolith. These bodies will evolve in response to very small perturbations such as micrometeoroid impacts, planetary flybys, and the YORP effect. A detailed understanding of asteroid mechanical evolution is needed in order to predict the surface characteristics of as-of-yet unvisited bodies, to understand the larger context of samples from sample return missions, and to mitigate risks for both manned and unmanned missions to asteroidal bodies. Due to observation of rocky regions on asteorids such as Eros and Itokawa, it has been hypothesized that grain size distribution with depth on an asteroid may be inhomogeneous: specifically, that large boulders have been mobilized to the surface. In terrestrial environments, this size-dependent sorting to the surface of the sample is called the Brazil Nut Effect. The microgravity and acceleration environment on the ISS is similar that of a small asteroid. Thus, Strata-1 investigates size segregation of regolith in an environment analogous to that of small bodies. Strata-1 consists of four regolith simulants in evacuated tubes, as shown in Figure 1 (Top and Middle). The simulants are (1) a crushed and sieved ordinary chondrite meteorite to simulate an asteroidal surface, (2) a carbonaceous chondrite simulant with a mixture of fine and course particles, and two simplified silicate glass simulants; (3) one with angular and (4) another with spherical particles. These materials were chosen to span a range of granular

  5. Continuous acid dew point measurement in coal-fired power plants; Kontinuierliche Saeuretaupunktmessung in Braunkohlekraftwerken

    Foedisch, Holger; Schulz, Joerg; Schengber, Petra; Dietrich, Gabriele [Dr. Foedisch Umweltmesstechnik AG, Markranstaedt (Germany)

    2009-07-01

    The reduction of flue gas losses is one option to increase power plant efficiency. The target is the optimised low waste gas temperature. When applying lignite and other high-sulphur fuels the temperature of the flue gas is mainly determined by the acid dew point. Temperature of the flue gas system is to amount some 10 to 20 K above the assumed acid dew point. The acid dew point measuring system AMD 08 is able to detect the real acid dew point in a quasi-continuous way. Thus, it is possible to deliberately decrease waste gas temperature. (orig.)

  6. On-Line Self-Calibrating Single Crystal Sapphire Optical Sensor Instrumentation for Accurate and Reliable Coal Gasifier Temperature Measurement

    Kristie Cooper; Gary Pickrell; Anbo Wang

    2005-11-01

    This report summarizes technical progress April-September 2005 on the Phase II program ''On-Line Self-Calibrating Single Crystal Sapphire Optical Sensor Instrumentation for Accurate and Reliable Coal Gasifier Temperature Measurement'', funded by the Federal Energy Technology Center of the U.S. Department of Energy, and performed by the Center for Photonics Technology of the Bradley Department of Electrical and Computer Engineering at Virginia Tech. The outcome of the first phase of this program was the selection of broadband polarimetric differential interferometry (BPDI) for further prototype instrumentation development. This approach is based on the measurement of the optical path difference (OPD) between two orthogonally polarized light beams in a single-crystal sapphire disk. The objective of this program is to bring the sensor technology, which has already been demonstrated in the laboratory, to a level where the sensor can be deployed in the harsh industrial environments and will become commercially viable. Due to the difficulties described on the last report, field testing of the BPDI system has not continued to date. However, we have developed an alternative high temperature sensing solution, which is described in this report. The sensing system will be installed and tested at TECO's Polk Power Station. Following a site visit in June 2005, our efforts have been focused on preparing for that field test, including he design of the sensor mechanical packaging, sensor electronics, the data transfer module, and the necessary software codes to accommodate this application.. We are currently ready to start sensor fabrication.

  7. A brief introduction to the Tavan Tolgoi coking coal deposit

    1992-01-01

    The Tavan Tolgoi coal field is located near the settlement Tsogttsetsii in the South Gobi province, 540 km south of Ulaanbaatar and 96 km east of Dalan Zadgad. The nearest railway stations are Choir, Khar-Airag and Sainshand and are located a distance of about 390 to 450 km, to the northeast of the coal field. An unimproved road connects the property with the railway stations at this time. The Tavan Tolgoi coal field covers 220 square km of land. The coal bearing strata contains 16 coal seams from 3 to 30 m thick with a total average thickness of 165 m. As per the geological survey, the proven and probable reserves of the Tavan Tolgoi coal field are estimated at 5 billion tonnes. Of the 5 billion tonnes, 77.5% or 3.9 billion tonnes are expected to be washed and will produce 2.16 billion tonnes (55% wash recovery) of clean coking coal. 1.41 billion tonnes or 36% of the washed coal will be middlings and available for steam coal, and 9% or 0.33 billion tonnes will be washed or gob. The remaining 1.2 billion tonnes can be mined and sold raw as steam coal. Water, electricity supplies and transportation will have to be developed. Research on this has been done. Markets are envisaged to be within Mongolia, and in the Asia Pacific region. Foreign investment will be needed. 5 figs., 6 tabs.

  8. Shale Failure Mechanics and Intervention Measures in Underground Coal Mines: Results From 50 Years of Ground Control Safety Research

    2015-01-01

    Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining. PMID:26549926

  9. Characterization of Egyptian coal from Sinai using Moessbauer spectroscopy

    Eissa, N.A.; Abdel Meguid, M.M.; Deriu, A.; Albanese, G.

    1983-08-01

    The presence of iron bearing minerals in coal makes the Moessbauer Spectroscopy (MS) extremely useful for characterization of coals from different localities. In this paper the MS has been applied to characterize Egyptian coal from Sinai (Maghara). The chemical analysis of this coal is given. The MS results showed that pyritic sulphur (pyrite and marcasite) is the only bearing mineral in Egyptian coal. A review is given for the iron bearing minerals in coals from different countries measured by MS. (author)

  10. Converting coal

    Avigliano, A. [Bedeschi (Italy)

    2006-10-15

    In September 2005, Bedeschi was commissioned to design and supply a coal unloading, conveying and storage facility for a new raw coal line system within Hatien II Cement Co. The new plant is composed of a grab unloader, a conveyor system, a storage shed with stacking and reclaiming facilities, a complete dedusting system and civil and steel structure engineering. The scope of supply includes a local fabrication portion; however, main components will be imported. The project will be completed in 21 months. The paper looks into the mechanics of loading and unloading coal. 4 figs., 4 photos.

  11. Description of vertical displacements in the active process of rock strata deformation under conditions of mining operations

    Piwowarski, W. (Akademia Gorniczo-Hutnicza, Cracow (Poland))

    1989-01-01

    Analyzes modeling vertical displacement in the evolution process of rock strata deformation caused by underground coal mining. The modeling results in a continuous description of the deformation process. Assumptions concerning model structure account for geometry of the phenomenon, while development of the deformation process is based on one physical mechanism. As a result of the analysis it has been stated that the deformation process is quantitatively similar to diffusion. On that basis the problem is described by differential equations. The class and order of the differential equations result from energy balance of the displacement field, while the analysis of the gradient of changes in the displacement field leads to a parabolic equation. The vertical displacement process in a transient state is characterized as a parabolic problem: one-dimensional, two-dimensional solenoidal, two-dimensional with one source of displacements. Equation solutions are based on Green's identity with boundary conditions. Modeling rock strata displacement in a transient state of deformation includes integration of differential equations and optimization of model parameters. The algorithm solution is written in form of a program for PC IBM/XT class computers. 41 refs.

  12. Coal competitiveness?

    Rogeaux, B.

    2006-01-01

    Will coal electrical plants be more competitive in the coming years? Answering this one cannot be limited to merely comparing estimates based on reference electricity production costs. The competitiveness of coal will indeed depend on the final product marketed, as the MWhs are not equal: is the purpose to produce base, half-base MWh? Does the electrical equipment structure require flexible MWh (for instance in the event of significant intermittent renewable energy amounts), and therefore plants able to adjust their power rapidly? But the competitiveness of coal will also depend on many factors that will correct reference cost estimates: uncertainties, risks, externalities. These factors will need to be appreciated on a case by case basis. We introduce some of the reasoning used to better appreciate the future competitiveness of coal, and the main factors conditioning it in three contrasting regions of the world: Europe, USA, china. (author)

  13. Development of mechanization of extraction in underground coal mining (part I)

    Strzeminski, J

    1984-01-01

    The history of underground coal mining and history of mechanizing underground operations of cutting, strata control, mine haulage, hoisting and ventilation are discussed. The following development periods are characterized: until 1769 (date of steam engine invention by J. Watt), from 1769 to 1945 (period of partial mechanization of operations in underground coal mining), from 1945 (period of comprehensive mechanization and automation). A general description of mining in the first development period is given. Evaluation of the second development period concentrates on mechanization in underground coal mining. The following equipment types are described: cutting (pneumatic picks and pneumatic drills, coal saws developed by Eickhoff, coal cutters developed after 1870, cutter loaders patented in 1925-1927, coal plows and coal cutter loaders), mine haulage (mine cars, conveyors developed in the United Kingdom, Germany and Russia, Poland), strata control at working faces (timber props, steel friction props, roof bars), strata control in the goaf (room and pillar mining, stowing, minestone utilization for stowing in Upper Silesia, hydraulic stowing in Upper Silesia). 5 references.

  14. Coal - 97

    Sparre, C.

    1997-01-01

    The report deals with the use of coal and coke during 1996. Some information about techniques, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1996 was 1,2 mill tons and 50% higher than in 1995. The increase is probably temporary and due to high prices of electricity because of lack of water power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generation plants. During the top year 1987 coal was used in 18 hotwater plants and 11 co-generation plants. 1996 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1996 was 1,6 mill tons like the year before. 1,2 mill tons coke were produced. The coke consumption in the industry was 1,5 mill tons. 0,3 mill tons of coke were imported. The average price of steam coal imported in Sweden in 1996 was 340 SEK/ton or 2% higher than in 1995. For the world, the average import price was 51,5 USD/ton, nearly the same as the year before. The contract prices for delivery during 1997 are about equal as the end of 1996. All Swedish plants meet their emission limits of dust, SO 2 and NO x given by county administrations or concession boards

  15. An overview of the geological controls in underground coal gasification

    Mohanty, Debadutta

    2017-07-01

    Coal’s reign will extend well into this millennium as the global demand for coal is expected to increase on average by 2-1% per year through 2019. Enhanced utilization of the domestic coal resource through clean coal technologies is necessary to meet the energy needs while achieving reduced emissions. Underground coal gasification (UCG) is one of such potential technologies. Geology of the area plays decisive role throughout the life of a UCG project and imperative for every phase of the project cycle starting from planning, site selection, design to cessation of operations and restoration of the site. Impermeable over/underlying strata with low porosity and less deformation are most suitable for UCG processes as they act as seal between the coal seam and the surrounding aquifers while limiting the degree of subsidence. Inrush of excess water into the gasification chamber reduces the efficacy of the process and may even quench the reactions in progress. Presence of fresh water aquifer in the vicinity of target coal seam should be abandoned in order to avoid groundwater contamination. UCG is not a proven technology that is still evolving and there are risks that need to be monitored and managed. Effective shutdown programme should intend at minimising the post-burn contaminant generation by flushing out potential organic and inorganic contaminants from the underground strata and treating contaminants, and to restore ground water quality to near baseline conditions.

  16. Coal ash monitoring equipment

    Clayton, C G; Wormald, M R

    1978-10-02

    The monitoring equipment is used to determine the remainder from combustion (ash slack) of coal in wagons designed for power stations. Next to the rails, a neutron source (252 Cf, 241 Am/Be) is situated, which irradiates the coal with neutrons at a known dose, which produces the reaction 27 Al (n ..gamma..) Al 28. The aluminium content is a measure of the remainder. The 1.78 MeV energy is measured downstream of the rail with a detector. The neutron source can only act in the working position of a loaded wagon.

  17. Coal -98

    Sparre, C.

    1998-01-01

    The following report deals with the use of coal and coke during 1997. Some information about technic, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from SCB have also been used. The use of steam coal for heating purposes during 1997 was 730 000 tons and about 500 000 tons lower than in 1996. The extremely high figures of 1996 were due to twice the production of electricity because of lack of hydro power. The co-generation plants were the main users of coal. The minor plants have increased their use of forest fuels. Probably the use of steam coal will go down in the immediate years both in the heat generating and the co-generating plants. Some foreign analysts, however, estimate a doubled use of coal for energy use after 2020 because of the plans to phase out the nuclear power. During the top year 1987 coal was used in 18 hot water plants and 11 co-generation plants. 1997 these figures are 2 and 8. Taxes and environmental reasons explain this trend. The use of steam coal in the industry has been constant at the level 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1997 was 1.6 mill tons like the year before. 1.2 mill tons coke were produced. The coke consumption in the industry was 1.5 Mill tons. 0.3 mill tons of coke were imported. Several other plants have plans to replace the coal with forest fuels, waste fuels and NG. Even the biggest plant, Vaesteraas, has plans to build a block for bio fuels. Helsingborg has started to use wood pellets. The pellets replace most of the coal for the heat production in the co-generation plant. Norrkoeping Kraft AB has taken a fluid bed boiler for different fuels in operation, leading to more than half the coal consumption compared with previous years. They have also rebuilt one of their travelling grates for bio fuels. Stockholm

  18. A high resolution interferometric method to measure local swelling due to CO2 exposure in coal and shale

    Pluymakers, A.; Liu, J.; Kohler, F.; Renard, F.; Dysthe, D.

    2018-01-01

    We present an experimental method to study time-dependent, CO2-induced, local topography changes in mm-sized composite samples, plus results showing heterogeneous swelling of coal and shale on the nano- to micrometer scale. These results were obtained using high resolution interferometry

  19. Coal 95

    Sparre, C.

    1995-01-01

    The report deals with the use of coal and coke in Sweden during 1994. Some information about technology, environmental questions and markets are also given. Data have been collected by questionnaires to major users and by telephone to minor users. Preliminary statistical data from Statistics Sweden have also been used.The use of steam coal for heating purposes has been unchanged during 1994 at a level of 1 Mtons. The production in the cogeneration plants has been constant, but has increased for electricity production. The minor plants have increased their use of forest fuels. The use of steam coal will probably go down in the next years both for heat and cogeneration plants. During the top year 1987 coal was used in 18 hot water and 11 cogeneration plants. 1994 these figures are 3 and 12. Taxes and environmental reasons explain this trend. The use of steam coal in industry has been constant at the level 0.7 Mtons. The import of metallurgical coal in 1993 was 1.6 Mtons, like 1992. Import of 0.3 Mtons of coke gives the total consumption of coke in industry as 1.5 Mtons. the average price of steam coal imported to Sweden was 317 SEK/ton, 3% higher than 1993. All Swedish plants meet their emission limit of dust, SO 2 and NO x as given by county administrations or concession boards. The cogeneration plants all have some SO 2 removal system. The biggest cogeneration plant (Vaesteraas) has recently invested in a SCR NO x cleaning system. Most other plants use low NO x burners or SNR injection systems based on ammonia or urea. 2 figs, 13 tabs

  20. Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

    Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

    2013-07-01

    The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

  1. Temperature profiles of coal stockpiles

    Sensogut, C.; Ozdeniz, A.H.; Gundogdu, I.B. [Dumlupinar University, Kutahya (Turkey). Mining Engineering Department

    2008-07-01

    Excess of produced coals should be kept in the stockyards of the collieries. The longer the duration time for these coals, the greater possibility for spontaneous combustion to take place. Spontaneously burnt coals result in economical and environmental problems. Therefore, taking the necessary precautions before an outburst of the spontaneous combustion phenomenon is too important in terms of its severe results. In this study, a stockpile having industrial dimensions was formed in coal stockyard. The effective parameters on the stockpiles of coal such as temperature and humidity of the weather, time, and atmospheric pressure values were measured. The interior temperature variations of these stockpiles caused by the atmospheric conditions were also measured. The interior temperature distribution maps of the stockpile together with maximum and minimum temperature values were expressed visually and numerically by the assistance of obtained data.

  2. Conodont zonation of Lower Triassic strata in Slovenia

    Tea Kolar-Jurkovšek

    2015-12-01

    Full Text Available The paper presents the results of a conodont study carried out in the Triassic strata in the area of the Slovenian part of the Southern Alps, External Dinarides and the Transition region between the External and Internal Dinarides. The following conodont zones have been distinguished: Hindeodus praeparvus Z., H. parvus Z., Isarcicella lobata Z., I. staeschei – I. isarcica Z., H. postparvus Z., Hadrodontina aequabilis Z., Ha. anceps Z., Eurygnathodus costatus Z., Neospathodus planus Z., N. robustus Z., Platyvillosus corniger Z., Pl. regularis Z., Pachycladina obliqua Z., Foliella gardenae Z., Triassospathodus hungaricus Z., T. symmetricus Z., N. robustispinus - T. homeri Z. and T. triangularis Z. The introduced conodont zonation spans from the Induan, including the Permian-Triassic boundary interval to the late Olenekian and is valid for the shallow shelf environments of western Tethys.

  3. Shales and other argillaceous strata in the United States

    Gonzales, S.; Johnson, K.S.

    1985-03-01

    This report presents detailed geologic and hydrologic data that describe shales and other argillaceous rocks; data are from the open literature. These data are intended to be used in the future to aid in assessment of various strata and their potential for repository siting. No observations, conclusions, or recommendations are made by the authors of this report relative to the suitability of various argillaceous rocks for waste disposal. There are, however, other published reports that contain technical data and evaluative statements regarding the suitability of various argillaceous rocks for repository siting. Where appropriate, the authors of this report have referenced this previously published literature and have summarized the technical data. 838 refs., 121 figs., 6 tabs

  4. Shales and other argillaceous strata in the United States

    Gonzales, S.; Johnson, K.S.

    1985-03-01

    This report presents detailed geologic and hydrologic data that describe shales and other argillaceous rocks; data are from the open literature. These data are intended to be used in the future to aid in assessment of various strata and their potential for repository siting. No observations, conclusions, or recommendations are made by the authors of this report relative to the suitability of various argillaceous rocks for waste disposal. There are, however, other published reports that contain technical data and evaluative statements regarding the suitability of various argillaceous rocks for repository siting. Where appropriate, the authors of this report have referenced this previously published literature and have summarized the technical data. 838 refs., 121 figs., 6 tabs.

  5. Simulation of depth distribution of geological strata. HQSW program

    Czubek, J.A.; Kolakowski, L.

    1987-01-01

    The method of simulation of the layered geological formation for a given geological parameter is presented. The geological formation contains at least two types of layers and is given with the depth resolution Δh corresponding to the thickness of the hypothetical elementary layer. Two types of geostatistical distributions of the rock parameters are considered: modified normal and modified lognormal for which the input data are expected value and the variance. The HQSW simulation program given in the paper generates in a random way (but in a given repeatable sequence) the thicknesses of a given type of strata, their average specific radioactivity and the variance of specific radioactivity within a given layer. 8 refs., 14 figs., 1 tab. (author)

  6. Variation in the immune responses against Plasmodium falciparum merozoite surface protein-1 and apical membrane antigen-1 in children residing in the different epidemiological strata of malaria in Cameroon.

    Kwenti, Tebit Emmanuel; Moye, Adzemye Linus; Wiylanyuy, Adzemye Basil; Njunda, Longdoh Anna; Nkuo-Akenji, Theresa

    2017-11-09

    Studies to assess the immune responses against malaria in Cameroonian children are limited. The purpose of this study was to assess the immune responses against Plasmodium falciparum merozoite surface protein-1 (MSP-1 19 ) and apical membrane antigen-1 (AMA-1) in children residing in the different epidemiological strata of malaria in Cameroon. In a cross-sectional survey performed between April and July 2015, 602 children between 2 and 15 years (mean ± SD = 5.7 ± 3.7), comprising 319 (53%) males were enrolled from five epidemiological strata of malaria in Cameroon including: the sudano-sahelian (SS) strata, the high inland plateau (HIP) strata, the south Cameroonian equatorial forest (SCEF) strata, the high western plateau (HWP) strata, and the coastal (C) strata. The children were screened for clinical malaria (defined by malaria parasitaemia ≥ 5000 parasites/µl plus axillary temperature ≥ 37.5 °C). Their antibody responses were measured against P. falciparum MSP-1 19 and AMA-1 vaccine candidate antigens using standard ELISA technique. A majority of the participants were IgG responders 72.1% (95% CI 68.3-75.6). The proportion of responders was higher in females (p = 0.002) and in children aged 10 years and above (p = 0.005). The proportion of responders was highest in Limbe (C strata) and lowest in Ngaoundere (HIP strata) (p malaria (p malaria parasites. The immune responses varied considerably across the different strata: the highest levels observed in the C strata and the lowest in the HIP strata. Furthermore, malaria transmission in Cameroon could be categorized into two major groups based on the serological reaction of the children: the southern (comprising C and SCEF strata) and northern (comprising HWP, HIP and SS strata) groups. These findings may have significant implications in the design of future trials for evaluating malaria vaccine candidates in Cameroon.

  7. Design of Compressed Sensing Algorithm for Coal Mine IoT Moving Measurement Data Based on a Multi-Hop Network and Total Variation

    Gang Wang

    2018-05-01

    Full Text Available As the application of a coal mine Internet of Things (IoT, mobile measurement devices, such as intelligent mine lamps, cause moving measurement data to be increased. How to transmit these large amounts of mobile measurement data effectively has become an urgent problem. This paper presents a compressed sensing algorithm for the large amount of coal mine IoT moving measurement data based on a multi-hop network and total variation. By taking gas data in mobile measurement data as an example, two network models for the transmission of gas data flow, namely single-hop and multi-hop transmission modes, are investigated in depth, and a gas data compressed sensing collection model is built based on a multi-hop network. To utilize the sparse characteristics of gas data, the concept of total variation is introduced and a high-efficiency gas data compression and reconstruction method based on Total Variation Sparsity based on Multi-Hop (TVS-MH is proposed. According to the simulation results, by using the proposed method, the moving measurement data flow from an underground distributed mobile network can be acquired and transmitted efficiently.

  8. Design of Compressed Sensing Algorithm for Coal Mine IoT Moving Measurement Data Based on a Multi-Hop Network and Total Variation.

    Wang, Gang; Zhao, Zhikai; Ning, Yongjie

    2018-05-28

    As the application of a coal mine Internet of Things (IoT), mobile measurement devices, such as intelligent mine lamps, cause moving measurement data to be increased. How to transmit these large amounts of mobile measurement data effectively has become an urgent problem. This paper presents a compressed sensing algorithm for the large amount of coal mine IoT moving measurement data based on a multi-hop network and total variation. By taking gas data in mobile measurement data as an example, two network models for the transmission of gas data flow, namely single-hop and multi-hop transmission modes, are investigated in depth, and a gas data compressed sensing collection model is built based on a multi-hop network. To utilize the sparse characteristics of gas data, the concept of total variation is introduced and a high-efficiency gas data compression and reconstruction method based on Total Variation Sparsity based on Multi-Hop (TVS-MH) is proposed. According to the simulation results, by using the proposed method, the moving measurement data flow from an underground distributed mobile network can be acquired and transmitted efficiently.

  9. Bulk analysis of coal

    Sowerby, B.D.

    1982-01-01

    Nuclear techniques used in the coal industry to determine specific energy, ash and moisture are outlined. Ash analysis by radioisotope X-ray techniques include a single X-ray measurement using a transmission or backscatter geometry and techniques with compensation for iron variations. Neutron techniques can be used to measure the concentration of some specific elements in coal. The measurement of specific energy, ash and moisture then depends on the correlation of the particular parameter with the measured elemental composition. Carbon can be determined by a combination of a measurement of 4.43 MeV 12 C gamma-rays from neutron inelastic scattering with a separate 60 Co gamma-ray scattering measurement. Sulphur meters are based on the measurement of 5.42 MeV neutron capture of gamma rays

  10. Coal preparation

    Anon.

    1991-01-01

    The acid rain control legislation has prompted the Department of Energy (DOE) to seek new technology using the Clean Coal Technology program solicitation. The main goal of the program is to reduce SO 2 emissions below 9 Mt/a (10 million stpy) and NO x emission below 5.4 Mt/a (6 million stpy) by the year 2000. This would be accomplished by using precombustion, combustion, post combustion and conversion technology. Utilities are considering installing new scrubbers, switching fuel or possibly deep clean. However, the time required to implement the control technology is short. Due to the legislation, about 110 plants will have to adopt one of the approaches. This paper reports that in characterization of coal, Ames Laboratory used a scanning electron microscope- based, automated image analysis (SEM-AIA) technique to identify coal and mineral matter association. Various forms of organic sulfur were identified using peroxyacetic acid oxidation of coal. This was followed by subsequent microscopic, GC-MS, and HRMS analysis by Southern Illinois University. In ultrafine grinding of coal, it was reported by the Mining and Mineral Institute of Alabama that silica sand or flint shot used less energy compared to steel ball mills

  11. Physical properties and strength of cohesive strata from a hazardous area at the Western long-term slope of the Turow surface mine

    Konderla, H; Suchnicka, H [Politechnika Wroclawska (Poland)

    1991-01-01

    Evaluates landslide hazards in the Turow brown coal mine in the area of a safety pillar of the Neisse river. Physical and mechanical properties of the following types of rocks from the pillar were investigated under laboratory conditions: cohesive Quaternary strata, clay layers adjacent to the coal seams and separating the seams, weathered and disintegrated granite, basalt and tuff (detritus). Rock samples were tested under conditions of tri-axial stresses, with natural water pore pressure, samples with a natural structure without artificial consolidation. The tests showed intensive fluctuations of rock properties. Nonhomogeneity of the samples and structural disturbances were determined. The tests showed the existence of landslide hazards in the Neisse river area. Recommendations for further investigations are made. 3 refs.

  12. Distilling coal

    Blythe, F C

    1914-09-14

    In the destructive distillation of bituminous coal, heavy hydrocarbon oil, such as petroleum, kerosine, shale oil, and heavy tar oil, obtained in some cases during the process, is added to the coal, which is then distilled under pressure and at a comparatively low temperature regulated so as to produce a large proportion of hydrocarbon oils and a small proportion of permanent gas. In one method, about 5 to 10 parts of hydrocarbon oil are mixed with 100 parts of crushed or ground coal, and the mixture is heated in a closed vessel, provided in some cases with an agitator, under a pressure of about 60 lb/in/sup 2/, and the temperature may be gradually raised to 350/sup 0/C and then to about 500/sup 0/C. The heating may be by means of superheated steam with or without external heat.

  13. Earth Conductivity Estimation from Through-the-Earth Measurements of 94 Coal Mines Using Different Electromagnetic Models

    Yan, Lincan; Waynert, Joseph; Sunderman, Carl

    2014-01-01

    Through-the-Earth (TTE) communication systems require minimal infrastructure to operate. Hence, they are assumed to be more survivable and more conventional than other underground mine communications systems. This survivability is a major advantage for TTE systems. In 2006, Congress passed the Mine Improvement and New Emergency Response Act (MINER Act), which requires all underground coal mines to install wireless communications systems. The intent behind this mandate is for trapped miners to...

  14. Indian coal industry: Growth perspective

    Sachdev, R.K.

    1993-01-01

    Growth perspective of Indian coal industry and their environmental aspects, are discussed. The complete coal chain comprises of mining including preparation and processing, transport, usage and disposal of solid, liquid and gaseous wastes. Proper environmental protection measures are therefore, required to be integrated at every stage. At mining stage, land reclamation, restoration of surface damaged by subsidence and proper treatment of effluents are the minimum requirement for effective environmental protection. Since coal will continue to be the major source of commercial energy in coming decades initiative will have to be taken in making coal a clean fuel from the point of view of its usage in different industries. Washing of high ash coals for reducing the ash content will go a long way in reducing the atmospheric pollution through better plant performance and reduced environmental pollution at the power plants. (author)

  15. Measurement of CO{sub 2}, CO, SO{sub 2}, and NO emissions from coal-based thermal power plants in India

    Chakraborty, N.; Mukheriee, I.; Santra, A.K.; Chowdhury, S.; Chakraborty, S.; Bhattacharya, S.; Mitra, A.P.; Sharma, C. [Jadavpur University, Calcutta (India). Dept. of Power Engineering

    2008-02-15

    Measurements of CO{sub 2} (direct GHG) and CO, SO{sub 2}, NO (indirect GHGs) were conducted on-line at some of the coal-based thermal power plants in India. The objective of the study was three-fold: to quantify the measured emissions in terms of emission coefficient per kg of coal and per kWh of electricity, to calculate the total possible emission from Indian thermal power plants, and subsequently to compare them with some previous studies. Instrument IMR 2800P Flue Gas Analyzer was used on-line to measure the emission rates Of CO{sub 2}, CO, SO{sub 2}, and NO at 11 numbers of generating units of different ratings. Certain quality assurance (QA) and quality control (QC) techniques were also adopted to gather the data so as to avoid any ambiguity in subsequent data interpretation. For the betterment of data interpretation, the requisite statistical parameters (standard deviation and arithmetic mean) for the measured emissions have been also calculated. The emission coefficients determined for CO{sub 2}, CO, SO{sub 2}, and NO have been compared with their corresponding values as obtained in the studies conducted by other groups. The total emissions of CO{sub 2}, CO, SO{sub 2}, and NO calculated on the basis of the emission coefficients for the year 2003-2004 have been found to be 465.667, 1.583, 4.058, and 1.129 Tg, respectively.

  16. Measuring drifted dust near coal transhipment in the harbour of Amsterdam, Netherlands; Meten aan verwaaiend stof bij kolenoverslag in het Amsterdams havengebied

    Weijers, E.P.; Rodink, R.; Hensen, A. [ECN Environment and Energy Engineering, Petten (Netherlands)

    2013-02-15

    For two months, particulate matter measurements were performed at the Rietlanden coal terminal in the Africa harbour in Amsterdam. At eight places around the coal terminal particulate matter concentrations were measured with relatively simple (and relatively inexpensive) optical sensors (which have been further developed by ECN). The primary purpose of the measurement campaign was to determine the performance and robustness of the sensors 'in the field'. After the satisfactory performance, the feasibility of a monitoring c.q. alarm system were studied and an estimate was made of particulate matter emissions from the terminal with a dispersion model during the measurement period [Dutch] Gedurende twee maanden zijn bij de Rietlanden kolenterminal in de Afrikahaven te Amsterdam fijnstofmetingen uitgevoerd. Op een achttal plaatsen rondom het bedrijf zijn fijnstofconcentraties gemeten met relatief eenvoudige (en relatief goedkope) optische sensoren (die door ECN verder zijn ontwikkeld). In de eerste plaats had de meetcampagne ten doel de prestatie en robuustheid van de sensoren 'in het veld' vast te stellen. Na gebleken geschiktheid is de haalbaarheid van een monitoring- c.q. alarmeringssysteem bestudeerd en is de fijnstofemissie afkomstig van de terminal geschat voor de periode van de metingen met een verspreidingsmodel.

  17. Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

    Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

    2010-12-01

    The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

  18. Formation and retention of methane in coal. Final report

    Hucka, V.J.; Bodily, D.M.; Huang, H.

    1992-05-15

    The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

  19. Coal petrology of coal seams from the Leao-Butia Coalfield, Lower Permian of the Parana Basin, Brazil - Implications for coal facies interpretations

    Silva, M.B. [Laboratorio de Oceanografia Geologica, Departamento de Geociencias, Fundacao Universidade Federal do Rio Grande, FURG, Av. Italia km 08, Campus Carreiros, 96201-900, Rio Grande, RS (Brazil); Kalkreuth, W.; Holz, M. [Instituto de Geociencias, UFRGS, Av. Bento Goncalves, 9500 91501-970 Porto Alegre, RS (Brazil)

    2008-02-01

    In the Leao-Butia Coalfield, Rio Grande do Sul the coal seams occur in the Rio Bonito Formation, Guata Group, Tubarao Supergroup of the Parana Basin, Brazil and are of Permian (Artinskian-Kungurian) age. This study is the first detailed investigation on the coal petrographic characterization of the coal-bearing sequence in relation to the depositional settings of the precursor mires, both in terms of whole seam characterization and in-seam variations. The study is based on the analyses of nine coal seams (I2, CI, L4, L3, L2, L1, S3, S2, S1), which were selected from core of borehole D-193, Leao-Butia and represent the entire coal-bearing sequence. The interpretation of coal facies and depositional environment is based on lithotype, maceral and microlithotype analyses using different facies-critical petrographic indices, which were displayed in coal facies diagrams. The seams are characterized by the predominance of dull lithotypes (dull, banded dull). The dullness of the coal is attributed to relatively high mineral matter, inertinite and liptinite contents. The petrographic composition is dominated by vitrinite (28-70 vol.% mmf) and inertinite (> 30 vol.% mmf) groups. Liptinite contents range from 7 to 30 vol.% (mmf) and mineral matter from 4-30 vol.%. Microlithotypes associations are dominated by vitrite, duroclarite, carbominerite and inertite. It is suggested that the observed vertical variations in petrographic characteristics (lithotypes, microlithotypes, macerals, vitrinite reflectance) were controlled by groundwater level fluctuations in the ancient mires due to different accommodation/peat accumulation rates. Correlation of the borehole strata with the general sequence-stratigraphical setting suggests that the alluvial fan system and the coal-bearing mudstone succession are linked to a late transgressive systems tract of sequence 2. Based on average compositional values obtained from coal facies diagrams, a deposition in a limno-telmatic to limnic coal

  20. New method for protecting mine roadways in thin coal seams by means of prefabricated yielding blocks

    Peknik, J

    1983-05-01

    The use of concrete blocks for strata control in mine roadways driven in thin coal seams is evaluated. Two types of prefabricated blocks are used: BZT blocks made of reinforced concrete and yielding elements or popilbet blocks made of a mixture of fly ash (from coal power plants) and concrete. When the popilbet blocks were used no yielding elements were necessary. Mechanical properties of blocks made of reinforced concrete were controlled by yielding elements. Mechanical properties (compression strength) of the popilbet blocks were controlled by proportion of water, cement and fly ash. The BZT and the popilbet blocks were used for strata control in mine roadways in coal seams from 60 to 80 cm thick and dip angle from 5 to 18 degrees. Use of the BZT and the popilbet blocks reduced roadway deformation by about 50% in comparison to traditional strata control methods (timber cribbings, use of waste rock, etc.). Use of the blocks is explained. The BZT and the popilbet blocks were placed in a roadway wall. Height of the block wall equaled coal seam thickness. Yielding arched steel supports and timber liners were used for strata control in the roadway. The popilbet blocks were 50% less expensive than the BZT blocks. 9 references

  1. Side abutment pressure distribution by field measurement

    Lian-guo Wang; Yang Song; Xing-hua He; Jian Zhang [State Key Laboratory for Geomechanics and Deep Underground Engineering, Xuzhou (China)

    2008-12-15

    Given the 7123 working face in the Qidong Coal Mine of the Wanbei Mining Group, nine dynamic roof monitors were installed in the crossheading to measure the amount and velocity of roof convergence in different positions and at different times and three steel bored stress sensors were installed in the return airway to measure rock stress at depth. On the basis of this arrangement, the rule of change of the distribution of the side abutment pressure with the advance of the working face and movement of overlying strata was studied. The rule of change and the stability of rock stress at depth were measured. Secondly, the affected area and stability time of the side abutment pressure were also studied. The results show that: 1) During working, the face advanced distance was from 157 m to 99 m, the process was not effected by mining induced pressure. When the distance was 82 m, the position of peak stress was 5 m away from the coal wall. When the distance was 37 m, the position of peak stress away from the coal wall was about 15 m to 20 m and finally reached a steady state; 2) the time and the range of the peak of side rock pressure obtained from stress sensors were consistent with the results from the dynamic roof monitors; 3) the position of the peak pressure was 25 m away from the coal wall. 14 refs., 6 figs.

  2. [Dust concentration analysis in non-coal mining. Exposure evaluation based on measurements performed by occupational hygiene laboratories in the years 2001-2005 in Poland].

    Bujak-Pietrek, Stella; Mikołajczyk, Urszula; Szadkowska-Stańczyk, Irena

    2011-01-01

    Non-coal mining includes the extraction of materials for construction (stone, gravel, sand and clay), chemical industry (salt and sulfur), metallurgy (metal ores, uranium and thorium) and other mining and quarrying. Regardless of the type of mining company one of the most common health hazards in this sector is exposure to high concentrations of dust occurring during the extraction of materials. Such activities as drilling, use of blasting agents, processing of raw material, its transportation and loading are the source of large amounts of dust containing crystalline silica. Data on exposure to dust, collected by industrial hygiene laboratories on the basis of dust concentration measurements in the work environment, were obtained from the sanitary inspection service. The analysis of dust concentrations at workplaces in non-coal mining covered the years 2001-2005. The average concentration of inhalable and respirable dust and the degree of results dispersion at workposts in different branches of non-coal mining (according to NACE rev1.1) were evaluated. Also there was estimated the percentage of surveys indicating dust concentrations above hygiene standards. Almost 5000 measurements of dust concentrations were performed in the years under study. The highest concentration of inhalable dust was noted for the production of salt (5.51 mg/m3), other mining and quarrying (4.30 mg/m3) and quarrying of slate (3.77 mg/m3). For respirable dust the highest concentrations were noted in other mining and quarrying (1.10 mg/m3), quarrying of slate (1.09 mg/m3) and quarrying of stone (0.81 mg/m3). Exposure to high concentrations of dust during the extraction of non-carbon is still an important hazard to human health. Almost for all workposts under study the excess of hygiene standards were observed.

  3. Coal Mines Security System

    Ankita Guhe; Shruti Deshmukh; Bhagyashree Borekar; Apoorva Kailaswar; Milind E.Rane

    2012-01-01

    Geological circumstances of mine seem to be extremely complicated and there are many hidden troubles. Coal is wrongly lifted by the musclemen from coal stocks, coal washeries, coal transfer and loading points and also in the transport routes by malfunctioning the weighing of trucks. CIL —Coal India Ltd is under the control of mafia and a large number of irregularities can be contributed to coal mafia. An Intelligent Coal Mine Security System using data acquisition method utilizes sensor, auto...

  4. Coal at the crossroads

    Scaroni, A.W.; Davis, A.; Schobert, H.; Gordon, R.L.; Ramani, R.V.; Frantz, R.L.

    1992-01-01

    Worldwide coal reserves are very large but coal suffers from an image of being an environmentally unfriendly and inconvenient fuel. Aspects discussed in the article include: coal's poor image; techniques for coal analysis, in particular instrumented techniques; developments in clean coal technology e.g. coal liquefaction, fluidized bed combustion, co-generation and fuel slurries; the environmental impact of mining and land reclamation; and health aspects. It is considered that coal's future depends on overcoming its poor image. 6 photos

  5. Prevention of spontaneous combustion in coal stockpiles : Experimental results in coal storage yard

    Fierro, V.; Miranda, J.L.; Romero, C.; Andrés, J.M.; Arriaga, A.; Schmal, D.; Visser, G.H.

    1999-01-01

    The spontaneous ignition of coal stockpiles is a serious economic and safety problem. This paper deals with oxidation and spontaneous combustion of coal piles laid in coal storage yard and the measures to avoid the heat losses produced. Investigations on self heating were carried out with five test

  6. Managed Multi-strata Tree + Crop Systems: An Agroecological Marvel

    P. K. Ramachandran Nair

    2017-12-01

    Full Text Available Today, when the emphasis on single-species production systems that is cardinal to agricultural and forestry programs the world over has resulted in serious ecosystem imbalances, the virtues of the time-tested practice of growing different species together as in managed Multi-strata Tree + Crop (MTC systems deserve serious attention. The coconut-palm-based multispecies systems in tropical homegardens and shaded perennial systems are just two such systems. A fundamental ecological principle of these systems is niche complementarity, which implies that systems that are structurally and functionally more complex than crop- or tree monocultures result in greater efficiency of resource (nutrients, light, and water capture and utilization. Others include spatial and temporal heterogeneity, perennialism, and structural and functional diversity. Unexplored or under-exploited areas of benefits of MTC systems include their ecosystem services such as carbon storage, climate regulation, and biodiversity conservation. These multispecies integrated systems indeed represent an agroecological marvel, the principles of which could be utilized in the design of sustainable as well as productive agroecosystems. Environmental and ecological specificity of MTC systems, however, is a unique feature that restricts their comparison with other land-use systems and extrapolation of the management features used in one location to another.

  7. Losses in the coal supply chain

    NONE

    2012-12-15

    This report examines the way coal can change as it passes along the coal chain. A great deal of the change is intended, through separation and sizing, to ensure the coal being mined matches the specification demanded by the customer. This report attempts to identify these changes and presents some of the issues faced by the coal supplier and user. Much of the change leads to a loss of mass in the coal. Some of the coal is left in the ground (intentionally and unintentionally), while elsewhere, full extraction might occur with the addition of non-coal materials from the surrounding rocks. In both cases, the mined coal often requires further processing. Coal processing by separation at preparation plants refines coal further and is where most of the mass loss occurs. Value is added by reducing ash content and improving heating value, thus providing a much more saleable product for the market. As soon as the coal leaves the mine, mass loss can occur either through natural deterioration of the fuel, through spillage or dust, or in extreme cases theft. In all cases measuring the amount of coal as it passes through the supply chain is required to verify that the coal reaching the consumer is of satisfactory quality and quantity. This can be done crudely by measuring stockpiles, to more sophisticated weighing systems at various points along the supply chain, and even measuring the volume held in a ship. Measurement is subject to error which must be minimised. Biomass needs to be processed in much the same way as coal, such as removing mineral matter and taking care in avoiding contamination.

  8. Coal industry annual 1997

    NONE

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs.

  9. Coal industry annual 1997

    1998-12-01

    Coal Industry Annual 1997 provides comprehensive information about US coal production, number of mines, prices, productivity, employment, productive capacity, and recoverable reserves. US Coal production for 1997 and previous years is based on the annual survey EIA-7A, Coal Production Report. This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report includes a national total coal consumption for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. 14 figs., 145 tabs

  10. Coal marketing manual 1987

    1987-01-01

    This manual provides information on the international coal market in tabulated format. Statistics are presented for the Australian coal industry, exports, currency movements, world coal production, coal and coke imports and exports. Detailed information is provided on the Australian coal industry including mine specific summaries. Pricing summaries for thermal and coking coal in 1987, coal quality standards and specifications, trends in coal prices and stocks. Imports and exports for World coal and coke, details of shipping, international ports and iron and steel production. An exporters index of Australian and overseas companies with industry and government contacts is included. 15 figs., 67 tabs.

  11. Coal industry annual 1996

    1997-11-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs

  12. Coal industry annual 1996

    NONE

    1997-11-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, and coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States.This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 24 million short tons for 1996. 14 figs., 145 tabs.

  13. Coal Industry Annual 1995

    NONE

    1996-10-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995.

  14. Coal Industry Annual 1995

    1996-10-01

    This report presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for Congress, Federal and State agencies, the coal industry, and the general public. Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility power producers that are not in the manufacturing, agriculture, mining, construction, or commercial sectors. Consumption for nonutility power producers not included in this report is estimated to be 21 million short tons for 1995

  15. Study of the correlation between the coal calorific value and coal ash content using X-ray fluorescence analysis

    Bolortuya, D.; Zuzaan, P.; Gustova, M.V.; Maslov, O.D.

    2013-01-01

    In this paper we have studied the possibility of determining the chemical elements in coal samples using X-ray fluorescence analysis and have found a relationship between the coal calorific value and its ash content with the coal moisture accounting. The amount of coal ash can be determined by the content of the basic chemical elements, such as Si, Sr, Fe, and Ca. It was concluded that the calorific value of coal can be estimated from the ash content in coal without the calorimetric measurements. These correlation coefficients were calculated for several coal mines in Mongolia. The results are in good agreement with the results of chemical analysis

  16. Coal and Energy.

    Bryant, Reba; And Others

    This teaching unit explores coal as an energy resource. Goals, student objectives, background information, and activity options are presented for each major section. The sections are: (1) an introduction to coal (which describes how and where coal was formed and explains the types of coal); (2) the mining of coal (including the methods and ways of…

  17. Comparative emissions from Pakistani coals and traditional coals

    Du, Y X [Guangzhou Medical College (China). Dept. of Hygiene; Huang, L F [Guangzhou Health and Anti-epidemic Station (China)

    1994-12-31

    Briquette coal has been widely used for domestic cooking and heating in many Chinese cites over the last two decades. To determine whether burning briquette coal contributes significantly to indoor air pollution, a study was performed in cities-of Southern China in which the measured levels of SO{sub 2}, NO{sub x}, TSP, SD, B(a)P in the kitchens of coal burning families were compared with levels obtained in families using gas. Significantly higher contentions of these pollutants, whose peaks correlated with daily cooking episodes, were detected in coal burning families. The levels of TSP and B(a)P were further found to be dependent on cooking methods, with deep frying and stir-frying of meat generating the most indoor TSP and B(a)P. Briquette coal burning was found to be the source of B(a)P contamination in food. A higher incidence of chronic pharyngitis as well as a suppressed salivary bacteriolytic enzyme activity were found in children of coal burning families. Epidemiologic and laboratory studies also show a close association between coal burning and the incidence of lung cancer in females. (author)

  18. Thermal maturity patterns in Pennsylvanian coal-bearing rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania: Chapter F.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Ruppert, Leslie F.; Trippi, Michael H.; Hower, James C.; Grady, William C.; Levine, Jeffrey R.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    Thermal maturation patterns of Pennsylvanian strata in the Appalachian basin and part of the Black Warrior basin were determined by compiling previously published and unpublished percent-vitrinite-reflectance (%R0) measurements and preparing isograd maps on the basis of the measurements. The isograd values range from 0.6 %R0 in Ohio and the western side of the Eastern Kentucky coal field to 5.5 %R0 in the Southern field in the Pennsylvania Anthracite region, Schuylkill County, Pa. The vitrinite-reflectance values correspond to the American Society of Testing Materials (ASTM) coal-rank classes of high-volatile C bituminous to meta-anthracite, respectively. In general, the isograds show that thermal maturity patterns of Pennsylvanian coals within the Appalachian basin generally decrease from east to west. In the Black Warrior basin of Alabama, the isograds show a circular pattern with the highest values (greater than 1.6 %R0) centered in Jefferson County, Ala. Most of the observed patterns can be explained by variations in the depth of burial, variations in geothermal gradient, or a combination of both; however, there are at least four areas of higher ranking coal in the Appalachian basin that are difficult to explain by these two processes alone: (1) a set of west- to northwest-trending salients centered in Somerset, Cambria, and Fayette Counties, Pa.; (2) an elliptically shaped, northeast-trending area centered in southern West Virginia and western Virginia; (3) the Pennsylvania Anthracite region in eastern Pennsylvania; and (4) the eastern part of the Black Warrior coal field in Alabama. The areas of high-ranking coal in southwestern Pennsylvania, the Black Warrior coal field, and the Pennsylvania Anthracite region are interpreted here to represent areas of higher paleo-heat flow related to syntectonic movement of hot fluids towards the foreland associated with Alleghanian deformation. In addition to the higher heat flow from these fluids, the Pennsylvania

  19. Distribution of the order Proetida (Trilobita in Baltoscandian Ordovician strata

    Pärnaste, Helje

    2009-03-01

    Full Text Available The trilobite order Proetida forms a minor but important faunal element within the Ordovician strata of Baltoscandia. This review follows the current systematic, taxonomic, and stratigraphical usage and discusses the distribution of these trilobites within the context of the Confacies Belt model. A database of species-level information was derived from numerous publications relating to the Scandinavian and Baltic states and relevant neighbouring regions. Important additional information on stratigraphical occurrences of genera has been derived from glacial erratic boulders (geschiebe from northern Germany and adjacent areas. The representatives from Baltoscandia of three superfamilies, Bathyuroidea, Aulacopleuroidea, and Proetoidea, are listed. The genus level was chosen as the most practicable to plot on the maps, one showing the time interval for the Kukruse Regional Stage (or Global Stage Slice Sa1, the other that for the Pirgu and Porkuni stages (or stage slices Ka4 and Hi1–Hi2. These intervals each show a diversity peak within the ranges of about 30 genera of Proetida and over 70 species from the Ordovician successions of Baltoscandia. Out of these a total of nine genera cross the Ordovician–Silurian boundary.The regional comparisons from within Baltoscandia show differences in facies dependency of certain genera, with possibly also a latitudinal component. During the late Ordovician the faunal resemblance appears to be closest to the neighbouring palaeocontinent Avalonia, suggesting a faunal exchange between or pathways to both continents from elsewhere. Besides climatic and geographical proximity of palaeocontinents, sea-level changes also have to be considered in explaining the distribution of Proetida in Baltoscandia.

  20. Local regularity analysis of strata heterogeneities from sonic logs

    S. Gaci

    2010-09-01

    Full Text Available Borehole logs provide geological information about the rocks crossed by the wells. Several properties of rocks can be interpreted in terms of lithology, type and quantity of the fluid filling the pores and fractures.

    Here, the logs are assumed to be nonhomogeneous Brownian motions (nhBms which are generalized fractional Brownian motions (fBms indexed by depth-dependent Hurst parameters H(z. Three techniques, the local wavelet approach (LWA, the average-local wavelet approach (ALWA, and Peltier Algorithm (PA, are suggested to estimate the Hurst functions (or the regularity profiles from the logs.

    First, two synthetic sonic logs with different parameters, shaped by the successive random additions (SRA algorithm, are used to demonstrate the potential of the proposed methods. The obtained Hurst functions are close to the theoretical Hurst functions. Besides, the transitions between the modeled layers are marked by Hurst values discontinuities. It is also shown that PA leads to the best Hurst value estimations.

    Second, we investigate the multifractional property of sonic logs data recorded at two scientific deep boreholes: the pilot hole VB and the ultra deep main hole HB, drilled for the German Continental Deep Drilling Program (KTB. All the regularity profiles independently obtained for the logs provide a clear correlation with lithology, and from each regularity profile, we derive a similar segmentation in terms of lithological units. The lithological discontinuities (strata' bounds and faults contacts are located at the local extrema of the Hurst functions. Moreover, the regularity profiles are compared with the KTB estimated porosity logs, showing a significant relation between the local extrema of the Hurst functions and the fluid-filled fractures. The Hurst function may then constitute a tool to characterize underground heterogeneities.

  1. A study on the forms of existence of germanium in uranium-bearing coals of Bangmai basin of Yunnan

    Zhang Shuling; Wang Shuying; Yin Jinshuang

    1988-07-01

    The Bangmai basin is an asymmetrical intermontane synclinal basin with a Hercynian-Yenshan granitic body (γ 3 3 -γ 5 2 ) as its basement. Its overlying strata are made up of the N 1 of coal-bearing clastic rocks of Neogene period. Germanium ore mostly occur within the N 1 2 coal-seam. Uranium, germanium-bearing coals are mainly lignites of low grade in coalation and belong to semidurain, semiclarain, duroclarain and clarodurain. In order to probe into the forms of existence of germanium in coal, six kinds of analytical methods (electronic probe analysis, separation of heavy liquid, grain-size analysis, electric osmosis, chemical extraction and grade-extraction) have been adopted. A simulated test of humic complex germanium in the laboratory was carried out. According to infrared spectral analysis, it is found that 1700 cm -1 wavecrest almost disappears, 1250 cm -1 peak weakens and 1600 cm -1 peak strengthens, 1400 cm -1 peak slightly strengthens. No doubt, these illustrate the formatiion of humic germanium complex. Afterward, through differential thermal analysis and measurement of pH variation of media, it futher proves the presence of humic germanium complex. It is considered that the forms of existence of germanium in uranium-bearing coals mainly are: (1) In close chemical combination with organic matter, usually in the form of humic germanium complex and germanium organic compound; (2) In the state of adsorption, germanium is adsorbed by some organic matter, clay minerals and limonite etc.; (3) A very rare part occurring as isomorphous form

  2. Self-ignition of coal during in-situ gasification. Thermoanalytical investigations. Selbstentzuendung von Kohlen bei der Untertagevergasung. Thermoanalytische Untersuchungen

    Choi, J O

    1986-01-10

    The underground gasification of deep coal strata via boreholes presupposes flow ways for the gasifying agent and the gasified media with a sufficiently high degree of permeability. Canal burning during countercurrent flow in low depths has been tested as a technical method for linking boreholes and enhancing gas permeability. For the execution of in situ gasification the control or prevention of the spontaneous ignition of the coal under high pressure should not be ignored, because of self-ignition resulting from canal burning in the linking phase. To investigate enthalpy change during the oxidation of coal under various conditions, a device for differential thermal analysis (DTA) was developed and constructed with which temperature development as a result of oxidation in a flowing pressure-gas atmosphere could be observed. A caloric calibration of the device permitted a direct inference of enthalpic difference from differential thermal potential as a measured value. With a regression model for reaction kinetics, the intensity of heat development was linked with kinetic data; this permitted a description of the dependence of the oxidation process on temperature and material concentration. From the interconnections discovered between the carbonization degree and enthalpy change during oxidation we may conclude that the oxidation process is controlled by the emergence of thermal decomposition products. The heat tonality diagram of the DTA of coal oxidation can be divided into three phases and interpreted in connection with the different degrees of carbonization. The results of the investigation reveal that inactivation of the coal before the actual process of linking is of considerable importance. (MOS).

  3. Hydrogeology, groundwater flow, and groundwater quality of an abandoned underground coal-mine aquifer, Elkhorn Area, West Virginia

    Kozar, Mark D.; McCoy, Kurt J.; Britton, James Q.; Blake, B.M.

    2017-01-01

    abandoned mine workings in the Pocahontas No. 3 coal seam and underlying strata in various structural settings of the Turkey Gap and adjacent down-dip mines. Geophysical logging and aquifer testing were conducted on the boreholes to locate the coal- mine aquifers, characterize fracture geometry, and define permeable zones within strata overlying and underlying the Pocahontas No. 3 coal-mine aquifer. Water levels were measured monthly in the wells and showed a relatively static phreatic zone within subsided strata a few feet above the top of or within the Pocahontas No. 3 coal-mine aquifer (PC3MA). A groundwater-flow model was developed to verify and refine the conceptual understanding of groundwater flow and to develop groundwater budgets for the study area. The model consisted of four layers to represent overburden strata, the Pocahontas No. 3 coal-mine aquifer, underlying fractured rock, and fractured rock below regional drainage. Simulation of flow in the flooded abandoned mine entries using highly conductive layers or zones within the model, was unable to realistically simulate interbasin transfer of water. Therefore it was necessary to represent the coal-mine aquifer as an internal boundary condition rather than a contrast in aquifer properties. By representing the coal-mine aquifer with a series of drain nodes and optimizing input parameters with parameter estimation software, model errors were reduced dramatically and discharges for Elkhorn Creek, Johns Knob Branch, and other tributaries were more accurately simulated. Flow in the Elkhorn Creek and Johns Knob Branch watersheds is dependent on interbasin transfer of water, primarily from up dip areas of abandoned mine workings in the Pocahontas No. 3 coal-mine aquifer within the Bluestone River watershed to the east. For the 38th, 70th, and 87th percentile flow duration of streams in the region, mean measured groundwater discharge was estimated to be 1.30, 0.47, and 0.39 cubic feet per square mile (ft3/s/mi2

  4. Coal -94

    Sparre, C.

    1994-05-01

    This report deals with use of coal and coke during 1993; information about techniques, environmental questions and markets are also given. Use of steamcoal for heating purposes has been reduced about 3 % during 1993 to 1,0 mill tons. This is the case especially for the heat generating boilers. Production in co-generation plants has been constant and has increased for electricity production. Minor plants have increased their use of forest fuels, LPG and NG. Use of steamcoal will probably go down in the immediate years both in heat generating and co-generating plants. Coal-based electricity has been imported from Denmark during 1993 corresponding to about 400 000 tons of coal, when several of our nuclear plants were stopped. Use of steamcoal in the industry has been constant at 700 000 tons. This level is supposed to be constant or to vary with business cycles. The import of metallurgical coal in 1993 was 1,6 mill tons like the year before. 1,2 mill tons coke were produced. Coke consumption in industry was 1,4 mill tons. 0,2 mill tons of coke were imported. Average price of steamcoal imported to Sweden in 1993 was 308 SEK/ton or 13 % higher than in 1992; this can be explained by the dollar price level increasing 34% in 1993. For the world, the average import price was 50,0 USD/ton, a decrease of 6 %. The coal market during 1993 was affected by less consumption in Europe, shut downs of European mines and decreasing prices. High freight price raises in Russia has affected the Russian export and the market in northern Europe. The prices have been stabilized recently. All Swedish plants meet emission limits of dust, SO 2 and NO x . Co-generation plants all have some sort of SO 2 -removal system; the wet-dry method is mostly used. A positive effect of the recently introduced NO x -duties is a 40% reduction

  5. Coal statistics 1977

    Statistical Office of the European Communities

    1978-01-01

    Presents tables of data relating to the coal market in the European Community in 1977. The tables cover hard coal production, supply and trade; briquettes; cokes; lignite, brown coal briquettes and peat; and mines and coke ovens.

  6. Australian coal yearbook 1989

    Aylward, A [ed.

    1989-01-01

    This yearbook contains a mine directory; details of coal export facilities and ports; annual coal statistics; a buyers' guide; names and addresses of industry organisations and an index of coal mine owners.

  7. Coal industry annual 1993

    1994-12-06

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993.

  8. Coal industry annual 1993

    1994-01-01

    Coal Industry Annual 1993 replaces the publication Coal Production (DOE/FIA-0125). This report presents additional tables and expanded versions of tables previously presented in Coal Production, including production, number of mines, Productivity, employment, productive capacity, and recoverable reserves. This report also presents data on coal consumption, coal distribution, coal stocks, coal prices, coal quality, and emissions for a wide audience including the Congress, Federal and State agencies, the coal industry, and the general public. In addition, Appendix A contains a compilation of coal statistics for the major coal-producing States. This report does not include coal consumption data for nonutility Power Producers who are not in the manufacturing, agriculture, mining, construction, or commercial sectors. This consumption is estimated to be 5 million short tons in 1993

  9. Australian black coal statistics 1990

    1991-01-01

    This second edition of Australian black coal statistics replaces the Joint Coal Board's publication 'Black coal in Australia'. It includes an expanded international coal trade supplement. Sections cover resources of black coal, coal supply and demand, coal production, employment and productivity of mines, export data, coal consumption and a directory of producers.

  10. Characteristics of the Roof Behaviors and Mine Pressure Manifestations During the Mining of Steep Coal Seam

    Hong-Sheng, Tu; Shi-Hao, Tu; Cun, Zhang; Lei, Zhang; Xiao-Gang, Zhang

    2017-12-01

    A steep seam similar simulation system was developed based on the geological conditions of a steep coal seam in the Xintie Coal Mine. Basing on similar simulation, together with theoretical analysis and field measurement, an in-depth study was conducted to characterize the fracture and stability of the roof of steep working face and calculate the width of the region backfilled with gangue in the goaf. The results showed that, as mining progressed, the immediate roof of the steep face fell upon the goaf and backfilled its lower part due to gravity. As a result, the roof in the lower part had higher stability than the roof in the upper part of the working face. The deformation and fracture of main roof mainly occurred in the upper part of the working face; the fractured main roof then formed a "voussoir beam" structure in the strata's dip direction, which was subjected to the slip- and deformation-induced instability. The stability analysis indicated that, when the dip angle increased, the rock masses had greater capacity to withstand slip-induced instability but smaller capacity to withstand deformation-induced instability. Finally, the field measurement of the forces exerted on the hydraulic supports proved the characteristics of the roof's behaviors during the mining of a steep seam.

  11. 1982 Australian coal conference papers

    1982-01-01

    This third Australian coal conference included papers discussing the market for coal, finance and investment, use of computers, mining, coal research, coal preparation and waste disposal, marketing and trade, and the transport of coal. All papers have been individually abstracted.

  12. Oxy-coal Combustion Studies

    Wendt, J. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Lighty, J. [Univ. of Utah, Salt Lake City, UT (United States); Ring, T. [Univ. of Utah, Salt Lake City, UT (United States); Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Thornock, J. [Univ. of Utah, Salt Lake City, UT (United States); Y Jia, W. Morris [Univ. of Utah, Salt Lake City, UT (United States); Pedel, J. [Univ. of Utah, Salt Lake City, UT (United States); Rezeai, D. [Univ. of Utah, Salt Lake City, UT (United States); Wang, L. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, J. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States)

    2012-01-06

    The objective of this project is to move toward the development of a predictive capability with quantified uncertainty bounds for pilot-scale, single-burner, oxy-coal operation. This validation research brings together multi-scale experimental measurements and computer simulations. The combination of simulation development and validation experiments is designed to lead to predictive tools for the performance of existing air fired pulverized coal boilers that have been retrofitted to various oxy-firing configurations. In addition, this report also describes novel research results related to oxy-combustion in circulating fluidized beds. For pulverized coal combustion configurations, particular attention is focused on the effect of oxy-firing on ignition and coal-flame stability, and on the subsequent partitioning mechanisms of the ash aerosol.

  13. Ultravitrinite coals from Chukotka

    Lapo, A.V.; Letushova, I.A.

    1979-03-01

    Chemical and petrographic analysis was conducted on coals from the Anadyrya and Bukhti Ugol'noi deposits. Characteristics of the most prevalent type of vitrinite coals in both regions are presented here. Anadyrya coals belong to a transitional phase between brown coal and long flame. Ultravitrinite coals predominate. Gas coals from Bukti Ugol'noi have a higher carbon content than Anadyrya coals. They also have a higher hydrogen content and yield of initial resin. In several cases there was also a higher yield of volatile substances. Chukotka coals are characterized by a 10 percent higher initial resin yield than equally coalified Donetsk coals, other indicators were equal to those of Donetsk coals. Because of this, Chukotka coals are suitable for fuel in power plants and as raw materials in the chemical industry. (15 refs.) (In Russian)

  14. Inference of strata separation and gas emission paths in longwall overburden using continuous wavelet transform of well logs and geostatistical simulation

    Karacan, C. Özgen; Olea, Ricardo A.

    2014-06-01

    Prediction of potential methane emission pathways from various sources into active mine workings or sealed gobs from longwall overburden is important for controlling methane and for improving mining safety. The aim of this paper is to infer strata separation intervals and thus gas emission pathways from standard well log data. The proposed technique was applied to well logs acquired through the Mary Lee/Blue Creek coal seam of the Upper Pottsville Formation in the Black Warrior Basin, Alabama, using well logs from a series of boreholes aligned along a nearly linear profile. For this purpose, continuous wavelet transform (CWT) of digitized gamma well logs was performed by using Mexican hat and Morlet, as the mother wavelets, to identify potential discontinuities in the signal. Pointwise Hölder exponents (PHE) of gamma logs were also computed using the generalized quadratic variations (GQV) method to identify the location and strength of singularities of well log signals as a complementary analysis. PHEs and wavelet coefficients were analyzed to find the locations of singularities along the logs. Using the well logs in this study, locations of predicted singularities were used as indicators in single normal equation simulation (SNESIM) to generate equi-probable realizations of potential strata separation intervals. Horizontal and vertical variograms of realizations were then analyzed and compared with those of indicator data and training image (TI) data using the Kruskal-Wallis test. A sum of squared differences was employed to select the most probable realization representing the locations of potential strata separations and methane flow paths. Results indicated that singularities located in well log signals reliably correlated with strata transitions or discontinuities within the strata. Geostatistical simulation of these discontinuities provided information about the location and extents of the continuous channels that may form during mining. If there is a gas

  15. Coal Tar and Coal-Tar Pitch

    Learn about coal-tar products, which can raise your risk of skin cancer, lung cancer, and other types of cancer. Examples of coal-tar products include creosote, coal-tar pitch, and certain preparations used to treat skin conditions such as eczema, psoriasis, and dandruff.

  16. Characterization of interactions of coal surface with solvent by flow microcalorimetric measurement. 3; Netsuryo sokutei ni yoru sekitan hyomen to yozai tono sogo sayo no hyoka. 3

    Wang, N.; Sasaki, M.; Yoshida, T. [Hokkaido National Industrial Research Institute, Sapporo (Japan); Kotanigawa, T. [Japan International Corporation Agency, Tokyo (Japan)

    1996-10-28

    An investigation was given on the relationship between methanol adsorbing behavior of reformed coal surface and oxygen containing functional groups in coal. Akabira bituminous coal was air-oxidized or Yallourn brown coal was decarbonated in oil as a reformation treatment. Both of the treated and untreated coals showed an adsorption heat curve of the Langmuir type. The Akabira coal had its oxygen content and the adsorption heat increased as a result of the air oxidizing reformation treatment. The Yallourn coal had its oxygen content and adsorption heat decreased as a result decarbonation reformation treatment. Oxygen containing functional groups act as strong adsorption sites for methanol, and the maximum adsorption amount depends on oxygen content in the coals. Since the coal surface is non-uniform in terms of energy, methanol is adsorbed first into sites with higher molar adsorption heat, and then into lower sites sequentially. Therefore, distribution of the molar adsorption heat can be derived from the relationship between adsorption amount and adsorption heat by changing methanol adsorption amount. The distribution of molar adsorption heat becomes broader when the oxygen content is high, and narrower when low. 2 refs., 2 figs.

  17. Wettability determination by contact angle measurements: hvbB coal-water system with injection of synthetic flue gas and CO2.

    Shojai Kaveh, Narjes; Rudolph, E Susanne J; Wolf, Karl-Heinz A A; Ashrafizadeh, Seyed Nezameddin

    2011-12-01

    Geological sequestration of pure carbon dioxide (CO(2)) in coal is one of the methods to sequester CO(2). In addition, injection of CO(2) or flue gas into coal enhances coal bed methane production (ECBM). The success of this combined process depends strongly on the wetting behavior of the coal, which is function of coal rank, ash content, heterogeneity of the coal surface, pressure, temperature and composition of the gas. The wetting behavior can be evaluated from the contact angle of a gas bubble, CO(2) or flue gas, on a coal surface. In this study, contact angles of a synthetic flue gas, i.e. a 80/20 (mol%) N(2)/CO(2) mixture, and pure CO(2) on a Warndt Luisenthal (WL) coal have been determined using a modified pendant drop cell in a pressure range from atmospheric to 16 MPa and a constant temperature of 318 K. It was found that the contact angles of flue gas on WL coal were generally smaller than those of CO(2). The contact angle of CO(2) changes from water-wet to gas-wet by increasing pressure above 8.5 MPa while the one for the flue gas changes from water-wet to intermediate-wet by increasing pressure above 10 MPa. Copyright © 2011 Elsevier Inc. All rights reserved.

  18. Maxwell Strata and Cut Locus in the Sub-Riemannian Problem on the Engel Group

    Ardentov, Andrei A.; Sachkov, Yuri L.

    2017-12-01

    We consider the nilpotent left-invariant sub-Riemannian structure on the Engel group. This structure gives a fundamental local approximation of a generic rank 2 sub-Riemannian structure on a 4-manifold near a generic point (in particular, of the kinematic models of a car with a trailer). On the other hand, this is the simplest sub-Riemannian structure of step three. We describe the global structure of the cut locus (the set of points where geodesics lose their global optimality), the Maxwell set (the set of points that admit more than one minimizer), and the intersection of the cut locus with the caustic (the set of conjugate points along all geodesics). The group of symmetries of the cut locus is described: it is generated by a one-parameter group of dilations R+ and a discrete group of reflections Z2 × Z2 × Z2. The cut locus admits a stratification with 6 three-dimensional strata, 12 two-dimensional strata, and 2 one-dimensional strata. Three-dimensional strata of the cut locus are Maxwell strata of multiplicity 2 (for each point there are 2 minimizers). Two-dimensional strata of the cut locus consist of conjugate points. Finally, one-dimensional strata are Maxwell strata of infinite multiplicity, they consist of conjugate points as well. Projections of sub-Riemannian geodesics to the 2-dimensional plane of the distribution are Euler elasticae. For each point of the cut locus, we describe the Euler elasticae corresponding to minimizers coming to this point. Finally, we describe the structure of the optimal synthesis, i. e., the set of minimizers for each terminal point in the Engel group.

  19. Correlation chart of Pennsylvanian rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania showing approximate position of coal beds, coal zones, and key stratigraphic units: Chapter D.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Ruppert, Leslie F.; Trippi, Michael H.; Slucher, Ernie R.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    The Appalachian basin, one of the largest Pennsylvanian bituminous coal-producing regions in the world, currently contains nearly one-half of the top 15 coal-producing States in the United States (Energy Information Agency, 2006). Anthracite of Pennsylvanian age occurs in synclinal basins in eastern Pennsylvania, but production is minimal. A simplified correlation chart was compiled from published and unpublished sources as a means of visualizing currently accepted stratigraphic relations between the rock formations, coal beds, coal zones, and key stratigraphic units in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania. The thickness of each column is based on chronostratigraphic divisions (Lower, Middle, and Upper Pennsylvanian), not the thickness of strata. Researchers of Pennsylvanian strata in the Appalachian basin also use biostratigraphic markers and other relative and absolute geologic age associations between the rocks to better understand the spatial relations of the strata. Thus, the stratigraphic correlation data in this chart should be considered provisional and will be updated as coal-bearing rocks within the Appalachian coal regions continue to be evaluated.

  20. Swelling behavior of several bituminous coals and their thermally treated coals

    Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

    2007-07-01

    The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

  1. Fault Detection in Coal Mills used in Power Plants

    Odgaard, Peter Fogh; Mataji, Babak

    2006-01-01

    In order to achieve high performance and efficiency of coal-fired power plants, it is highly important to control the coal flow into the furnace in the power plant. This means suppression of disturbances and force the coal mill to deliver the required coal flow, as well as monitor the coal mill...... in order to detect faults in the coal mill when they emerge. This paper deals with the second objective. Based on a simple dynamic model of the energy balance a residual is formed for the coal mill. An optimal unknown input observer is designed to estimate this residual. The estimated residual is following...... tested on measured data of a fault in a coal mill, it can hereby be concluded that this residual is very useful for detecting faults in the coal mill....

  2. Record coking coal settlements

    Macdonald, C.

    2005-02-01

    The US$100/tonne psychological barrier in coking coal prices has been well and truly smashed. The article examines developments in coal pricing. It includes quotes from many senior executives in the coal industry as collected at McCloskey's Australian Coal.04 conference held in Sydney, 18-19 November 2004. 2 photos.

  3. COAL Conference Poster

    Brown, Taylor Alexander; McGibbney, Lewis John

    2017-01-01

    COAL Conference Poster This archive contains the COAL conference poster for the AGU Fall Meeting 2017 by Taylor Alexander Brown. The Inkscape SVG source is available at https://github.com/capstone-coal/coal-conference-poster/ under the Creative Commons Attribution-ShareAlike 4.0 International license.

  4. Queensland coal sets new records in 2001

    Smith, R.; Coffey, D.; Abbott, E.

    2002-01-01

    In 2001 the Queensland coal industry consolidated on record expansion in the export market over the past two years and again, increased its sales to overseas customers. New sales records were set in both the export and domestic markets. Unprecedented international demand for Queensland metallurgical coals coupled with improved prices and a favourable A$-US$ exchange rate created strong market conditions for the Queensland coal export industry, boosting confidence for further expansion and new developments. Australian coal exports in 2001 amounted to 194 Mt and are forecast to reach 275 million tonnes per annum (Mtpa) in 2020. The Queensland coal industry is poised to capture a significant share of this market growth. Queensland's large inventory of identified coal, currently estimated at more than 37 billion tonnes (raw coal m situ), is adequate to sustain the industry for many years and allow new opencut and underground mines to develop according to future market demand. Recent coal exploration successes are expected to add significant tonnage to the inventory (Coxhead, Smith and Coffey, 2002). Most of the coal exported from Queensland is mined in the Bowen Basin of central Queensland and additional tonnage of Walloon coal is exported by mines in the Moreton Basin and Surat Basin in south-east Queensland. The Walloon Coal Measures and its equivalents contain large resources of undeveloped opencut, high volatile, clean-burning thermal coal. The environmental advantages in the utilisation of these coals are now recognised and strong growth in production is expected in the near future for supply to both the domestic and export markets. Establishment of new rail transport and civil infrastructure will however, be required to support the development of large scale mining operations in this region

  5. Power Generation from Coal 2010

    NONE

    2010-07-01

    Coal is the biggest single source of energy for electricity production and its share is growing. The efficiency of converting coal into electricity matters: more efficient power plants use less fuel and emit less climate-damaging carbon dioxide. This book explores how efficiency is measured and reported at coal-fired power plants. With many different methods used to express efficiency performance, it is often difficult to compare plants, even before accounting for any fixed constraints such as coal quality and cooling-water temperature. Practical guidelines are presented that allow the efficiency and emissions of any plant to be reported on a common basis and compared against best practice. A global database of plant performance is proposed that would allow under-performing plants to be identified for improvement. Armed with this information, policy makers would be in a better position to monitor and, if necessary, regulate how coal is used for power generation. The tools and techniques described will be of value to anyone with an interest in the more sustainable use of coal.

  6. Coal option. [Shell Co

    1978-01-01

    This paper notes the necessity of developing an international coal trade on a very large scale. The role of Shell in the coal industry is examined; the regions in which Shell companies are most active are Australia, Southern Africa, Indonesia; Europe and North America. Research is being carried out on marketing and transportation, especially via slurry pipelines; coal-oil emulsions; briquets; fluidized-bed combustion; recovery of coal from potential waste material; upgrading of low-rank coals; unconventional forms of mining; coal conversion (the Shell/Koppers high-pressure coal gasification process). Techniques for cleaning flue gas (the Shell Flue Gas Desulfurization process) are being examined.

  7. Concerning coal: an anthology

    Mayer, M.; Hawse, M.L.; Maloney, P.J. [eds.

    1997-12-31

    The anthology takes a humanistic look at coal mining in Illinois. One of its goals is to increase public awareness of coal in American society; it also seeks to enhance understanding of the historical aspects of coal and to study the impact of coal on mining families. Many of the 25 selections in the anthology come from Coal Research Center publications, `Concerning coal` and `Mineral matters`. Articles are arranged in three parts entitled: life in the mining community; mining in folklore, story telling, literature, art and music; and technology as it affected the people of the coal fields. 117 refs., 25 photos. 1 map.

  8. Measurements of capillary pressure and electric permittivity of gas-water systems in porous media at elevated pressures : Application to geological storage of CO2 in aquifers and wetting behavior in coal

    Plug, W.J.

    2007-01-01

    Sequestration of CO2 in aquifers and coal layers is a promising technique to reduce greenhouse gas emissions. Considering the reservoir properties, e.g. wettability, heterogeneity and the caprocks sealing capacity, the capillary pressure is an important measure to evaluate the efficiency, the

  9. Coal information 1995

    1996-01-01

    This volume is a comprehensive reference book on current world coal market trends and long-term prospects to 2010. It contains an in-depth analysis of the 1995 international coal market covering prices, demand, trade, supply and production capacity as well as over 450 pages of country specific statistics on OECD and key non-OECD coal producing and consuming countries. The book also includes a summary of environmental policies on climate change and on coal-related air quality issues as well as essential facts on coal-fired power stations in coal-importing regions, on coal ports world-wide and on emission standards for coal-fired boilers in OECD countries. Coal Information is one of a series of annual IEA statistical publications on major energy sources; other reports are Oil and Gas Information and Electricity Information. Coal Information 1995 is published in July 1996. (author)

  10. Coal yearbook 1993

    Anon.

    1993-01-01

    This book is the first coal yearbook published by ATIC (France). In a first chapter, economical context of coal worldwide market is analyzed: comparative evaluations on coal exports and imports, coal industry, prices, production in USA, Australia, South Africa, China, former USSR, Poland, Colombia, Venezuela and Indonesia are given. The second chapter describes the french energy context: national coal production, imports, sectorial analysis, maritime transport. The third chapter describes briefly the technologies of clean coal and energy saving developed by Charbonnages de France: fossil-fuel power plants with combined cycles and cogeneration, fluidized beds for the recovery of coal residues, recycling of agricultural wastes (sugar cane wastes) in thermal power plant, coal desulfurization for air pollution abatement. In the last chapter, statistical data on coal, natural gas and crude oil are offered: world production, world imports, world exports, french imports, deliveries to France, coal balance, french consumption of primary energy, power generation by fuel type

  11. ACR coal 1992

    1992-01-01

    This publication is a comprehensive reference document on production, exports, prices and demand of coal in world markets. A forecast of demand by coal type and country up to the year 2000 is provided. Statistics of the Australian export industry are complemented by those of South Africa, USA, Canada, Indonesia, China, C.I.S. and Colombia. A very comprehensive coal quality specification for nearly all the coal brands exported from Australia, as well as leading non-Australian coal brands, is included.

  12. Assessing coal burnout

    Lowe, A. [Pacific Power, Sydney, NSW (Australia)

    1999-11-01

    Recent research has allowed a quantitative description of the basic process of burnout for pulverized coals to be made. The Cooperative Research Centre for Black Coal Utilization has built on this work to develop a coal combustion model which will allow plant engineers and coal company representatives to assess their coals for combustion performance. The paper describes the model and its validation and outlines how it is run. 2 figs.

  13. Evaluation study on rationalization of coal handling in snowy area

    Suesada, Yasuhiko; Yamagata, Keisuke; Kuwahara, Mitsuhiro

    1987-09-25

    The adhesion of coal to the coal handling facilities in large cool-fired power plants in the snowy area was investigated for siting them in the future. The amount of water derived from melted snow in addition to that from the rain fall were measured and the statistical amounts of rain and snow falls for the past ten years were examined. Then the amount of water derived from melted snow was calculated by regression. The result indicates that the amount of rain fall in summer is larger than that from melted snow. The moisture content of coal in a coal yard reaches the moisture content at which the coal readily adheres to the facilities after snow fall and it penetrates the pile of coal to the bottom with the lapse of time. The penetrating rate of it largely depends upon the particle distribution of coal as well as the ranks of coal. The adhesion of coal to the coal handling facilities is caused mainly by the amount of dust coal and the moisture content of coal. The amount of adhered coal estimated from the shear properties qualitatively agrees with the experimental result using a model of chute. Adding the dusting inhibitor exceeding the normal value increases the amount of of adhesion of coal. (13 figs, 3 tabs)

  14. Coal Bed Methane Primer

    Dan Arthur; Bruce Langhus; Jon Seekins

    2005-05-25

    During the second half of the 1990's Coal Bed Methane (CBM) production increased dramatically nationwide to represent a significant new source of income and natural gas for many independent and established producers. Matching these soaring production rates during this period was a heightened public awareness of environmental concerns. These concerns left unexplained and under-addressed have created a significant growth in public involvement generating literally thousands of unfocused project comments for various regional NEPA efforts resulting in the delayed development of public and fee lands. The accelerating interest in CBM development coupled to the growth in public involvement has prompted the conceptualization of this project for the development of a CBM Primer. The Primer is designed to serve as a summary document, which introduces and encapsulates information pertinent to the development of Coal Bed Methane (CBM), including focused discussions of coal deposits, methane as a natural formed gas, split mineral estates, development techniques, operational issues, producing methods, applicable regulatory frameworks, land and resource management, mitigation measures, preparation of project plans, data availability, Indian Trust issues and relevant environmental technologies. An important aspect of gaining access to federal, state, tribal, or fee lands involves education of a broad array of stakeholders, including land and mineral owners, regulators, conservationists, tribal governments, special interest groups, and numerous others that could be impacted by the development of coal bed methane. Perhaps the most crucial aspect of successfully developing CBM resources is stakeholder education. Currently, an inconsistent picture of CBM exists. There is a significant lack of understanding on the parts of nearly all stakeholders, including industry, government, special interest groups, and land owners. It is envisioned the Primer would being used by a variety of

  15. Abstracts of the first ORNL workshop on polycyclic aromatic hydrocarbons: characterization and measurement with a view toward personnel protection. [PAH from coal conversion

    Gammage, R.B. (comp.)

    1976-11-01

    This report contains the abstracts of papers presented at a workshop on polycyclic aromatic hydrocarbons (PAH) such as those produced by coal conversion technologies. Their often carcinogenic nature imposes the obligation of providing adequate protection and measurement devices for workers and for the general public. The primary questions are as follows: What should be measured. Where and how should it be measured. What are the maximum permissible concentrations. This workshop and future workshops are intended to bring these problems into better focus and to help establish a consensus on what needs to be done in order to provide a dosimetry effort that will ensure the adequate protection of personnel. There were 32 attendees of this one-day meeting. The papers and discussions included current industrial hygiene practices, the development of government agency guidelines for worker protection, and a wide range of analytical techniques for PAH detection, some of which are still in the research stage and are unproven. The workshop was held at ORNL on February 26, 1976.

  16. Continuous online nuclear analyzer of coal

    Rogers, R.S.C.; Bozorgmanesh, H.; Gozani, T.; Brown, T.

    1980-01-01

    Since CONAC is a relatively new concept in coal quality measurement, the present paper concentrates primarily on instrument development. The basic principles of elemental composition, moisture content and Btu measurements are described and typical measurement results presented. Then, since CONAC is under development specifically for quality control purposes, its advantages and potential applications in the coal circuit are discussed. The CONAC development work showed principles of CONAC operation (PNAA, moisture and Btu determinations) to be powerful and versatile tools for the analysis of coal; CONAC-type instrumentation is being developed for batch, laboratory usage. Such a device will enable a user to perform rapid coal sample analyses in a nondestructive fashion, leaving samples intact for further evaluation. It is felt that a batch laboratory, CONAC-type device will be of great use in the mining industry where the analysis of borehole samples are important in the evaluation of coal reserves and in the planning of mining operations

  17. Naturally Occurring Radioactive Materials in Uranium-Rich Coals and Associated Coal Combustion Residues from China.

    Lauer, Nancy; Vengosh, Avner; Dai, Shifeng

    2017-11-21

    Most coals in China have uranium concentrations up to 3 ppm, yet several coal deposits are known to be enriched in uranium. Naturally occurring radioactive materials (NORM) in these U-rich coals and associated coal combustion residues (CCRs) have not been well characterized. Here we measure NORM (Th, U, 228 Ra, 226 Ra, and 210 Pb) in coals from eight U-rich coal deposits in China and the associated CCRs from one of these deposits. We compared NORM in these U-rich coals and associated CCRs to CCRs collected from the Beijing area and natural loess sediments from northeastern China. We found elevated U concentrations (up to 476 ppm) that correspond to low 232 Th/ 238 U and 228 Ra/ 226 Ra activity ratios (≪1) in the coal samples. 226 Ra and 228 Ra activities correlate with 238 U and 232 Th activities, respectively, and 226 Ra activities correlate well with 210 Pb activities across all coal samples. We used measured NORM activities and ash yields in coals to model the activities of CCRs from all U-rich coals analyzed in this study. The activities of measured and modeled CCRs derived from U-rich coals exceed the standards for radiation in building materials, particularly for CCRs originating from coals with U > 10 ppm. Since beneficial use of high-U Chinese CCRs in building materials is not a suitable option, careful consideration needs to be taken to limit potential air and water contamination upon disposal of U- and Ra-rich CCRs.

  18. Proceedings of the Second APEC Coal Flow Seminar Proceedings

    NONE

    1995-12-05

    This proceedings includes papers presented at the Second APEC Coal Flow Seminar held at Shanghai in December, 1995. Three keynote speeches were presented, and two panel discussions were held. `Medium-term outlook for coal trade,` `Energy and the environment,` and `Progress with environmental control technology and technical exchanges between economies` were presented as keynote speeches. In the panel discussions, `Achieving low environmental impact from coal production and utilization` and `How to tackle environmental issues related to coal` were discussed. The Panel 1 was divided into Part 1 and Part 2. In the Part 1, overview of current environmental protection policy measures was discussed in relation to coal production and use in economies where coal consumption has been increasing significantly. In the Part 2, overview of current environmental protection policy measures was discussed in relation to coal production and use in major coal producing and consuming economies. 38 refs., 64 figs., 31 tabs.

  19. The European Coal Market: Will Coal Survive the EC's Energy and Climate Policies?

    Cornot-Gandolphe, Sylvie

    2012-01-01

    . Chapter 3 looks at international coal prices and their competitiveness compared with competing fuels. Chapter 4 provides an overview of EC regulations that are likely to shape the future demand of coal. Chapter 5 gives an overview of CCT and CCS development in Europe, while Chapter 6 presents the outlook of future coal demand and scenarios developed by the International Energy Agency and the European Commission. The second part of the report gives a detailed picture of the three largest European coal markets (Germany, Poland and the United Kingdom). It also looks at the Spanish coal market. Although coal in this country accounts for a small share of total energy consumption, recent austerity measures and their social impact put the sector into the public spotlight. A description of the coal market is given for each country. Then, key developments and issues pertaining to each country and its coal market are discussed. Chapter 7 analyses the impact of the phase-out of nuclear energy in Germany. Chapter 8 provides an overview of Poland's energy policy to 2030 and the CCS road-map prepared by the Bellona Foundation. Chapter 9 focuses on market reform of electricity in the United Kingdom and its impact on coal-fired power generation. Chapter 10 looks at coal subsidies in Spain and the impact of the drastic cut in coal mining subsidies decided by the government in May 2012. Annex 1 explains what the nature coal is and the main differences between steam coal (mainly used in power generation) and coking coal (used in the iron and steel industry). Annex 2 briefly analyses the use of coal in the steel industry. Annex 3 provides some useful unit conversions

  20. Fossil fuel energy resources of Ethiopia: Coal deposits

    Wolela, Ahmed [Department of Petroleum Operations, Ministry of Mines and Energy, Kotebe Branch Office, P. O. Box-486, Addis Ababa (Ethiopia)

    2007-11-22

    The gravity of Ethiopian energy problem has initiated studies to explore various energy resources in Ethiopia, one among this is the exploration for coal resources. Studies confirmed the presence of coal deposits in the country. The coal-bearing sediments are distributed in the Inter-Trappean and Pre-Trap volcanic geological settings, and deposited in fluvio-lacustrine and paludal environments in grabens and half-grabens formed by a NNE-SSW and NNW-SSE fault systems. Most significant coal deposits are found in the Inter-Trappean geological setting. The coal and coal-bearing sediments reach a maximum thickness of 4 m and 300 m, respectively. The best coal deposits were hosted in sandstone-coal-shale and mudstone-coal-shale facies. The coal formations of Ethiopia are quite unique in that they are neither comparable to the coal measures of the Permo-Carboniferous Karroo Formation nor to the Late Devonian-Carboniferous of North America or Northwestern Europe. Proximate analysis and calorific value data indicated that the Ethiopian coals fall under lignite to high volatile bituminous coal, and genetically are classified under humic, sapropelic and mixed coal. Vitrinite reflectance studies confirmed 0.3-0.64% Ro values for the studied coals. Palynology studies confirmed that the Ethiopian coal-bearing sediments range in age from Eocene to Miocene. A total of about 297 Mt of coal reserve registered in the country. The coal reserve of the country can be considered as an important alternative source of energy. (author)

  1. Evaluation of the effect of macerals on coal permeability in Tazareh and Parvadeh mines

    Farhang Sereshki

    2016-08-01

    Full Text Available In recent decades, the subject of gas emission in underground coal mines in many countries is an important subject. Many factors affect in gas emissions in coal seams. Geological and physical structures of coal are affecting on gas emissions'. Also, composition and mineralization of coal, affect in coal permeability for different gases. In this study, the relationship between maceral composition and coal permeability in Tazareh and Parvadeh mines has been studied. Accordingly, a laboratory studies to investigate the relationship between coal composition and coal permeability was done. In coal samples, with MFORR equipment the permeability test was done. With microscopic analysis, the maceral contents of coal such as Inertinite and Vitrinite have been measured. Accordingly, many coal samples of Parvadeh and Tazareh coal mines have the pyrite as the dominant mineral matter. Parvadeh coal samples has the average percentage of Vitrinite equal 81.34% and 10.52% Inertinite. Also, in the Tazareh coal samples in Eastern Alborz coal mines, the average percentage of Vitrinite is 69.31% and inertinite is 22.47%. The average percentage of Pyrite content in Parvadeh coal samples in Tabas coal mines is 2.38% and in the Tazareh coal samples in Eastern Alborz coal mines is 2.62%.  The permeability test results have been shown, which, with increase of Inertinite contents, the permeability of coal is increasing. Also, test results have been shown, there was a reduction in the coal permeability with increasing of mineral contents and carbonate contents of the coal. So, the coal permeability in Tabas coal samples is more than Eastern Alborz coal samples.

  2. Ways of intensifying the conventional chamber carbonization of hard coal

    Pelagalli, M.

    1986-12-01

    The intensification measures are intended to reduce both the investment cost and the operating cost via an increased performance factor. Automation had good results both in coal blending and in process monitoring and control. Coal blending, compression, and partial briquetting extend the range of coking coals.

  3. Central Heating Plant Coal Use Handbook. Volume 1: Technical Reference.

    1996-11-01

    CHUTES LIFT TRUCKS MONORAILS , TRAMWAYS J p WEIGHING, 0 MEASURING SCALES COAL METERS HOPPERS SAMPLERS 9 FIRING EQUIPMENT (Source: Power, February...Defense (DOD) installations employ coal- fired central energy plants, the U.S. Army Construction Engineering Research Laboratories (USACERL) was... fired central heat plant operations cost by improving coal quality specifications. The Handbook is tailored for military installation industrial

  4. Rapid pyrolysis of Serbian soft brown coals

    Jankes Goran

    2009-01-01

    Full Text Available Soft brown coals of the open coal fields of Kolubara and Kostolac are the main domestic energy sources of Serbia. This paper presents the results of investigations on rapid devolatilization of these two coals which have covered kinetics of devolatilization (based on total volatile yield, forms of sulphur and petrographic analysis of coal and char. Experiments of devolatilization were performed in inert gas (N2 at atmospheric pressure and in batch-type hot-wire screen reactor. The mass-loss values of both coals at selected final reaction temperatures (300-900°C and retention times (3-28 s were obtained. Anthony and Howard's kinetic model was applied over two temperature ranges (300-500 and 700-900°C. The types of sulphur as monosulphide, sulphate, pyritic, and organic sulphur were determined for chars and original coals. Strong transformation of pyrite was evident even at low temperatures (300°C. Devolatilization of all types of sulphur has started over 600 and at 900°C the content of sulphur in char remained only 66% of total sulphur in original coal. Microscopic investigations were carried out on samples prepared for reflected light measurements. The petrographic analysis included: the ratio of unchanged and changed coal, maceral types, the share of cenosferes, isotropic mixed carbonized grains, mixed grains, small fragments, clay, and pyrite. The change of the structure of devolatilized coal was also observed.

  5. Coal information 1996

    1997-01-01

    Coal Information (1997 edition) is the latest edition of a publication that has been produced annually by the IEA since 1983. The report is intended to provide both Member countries of the OECD and those employed in all sectors of the coal industry with information on current world coal market trends and long-term prospects. It includes information on coal prices, demand, trade, supply, production capacity, transport, environmental issues (including emission standards for coal-fired boilers), coal ports, coal-fired power stations and coal used in non -OECD countries. Part I of the publication contains a wide ranging review of world coal market developments in 1996 and current prospects to 2010. The review is based on historical data of OECD energy supply and demand, data on other world regions, projections of OECD coal supply, demand and trade and information provided by the CIAB. Part II provides, in tabular and graphical form, a more detailed and comprehensive statistical picture of coal developments and future prospects for coal in the OECD, by region and for individual Member countries. Readers interested in projections are strongly advised to read the notes for individual countries in Principles and Definitions in Part II. Coal statistics for non-OECD countries are presented in Part III of the book. Summary data are available on hard coal supply and end-use statistics for about 40 countries and regions world-wide. Data are based on official national submissions to the United Nations in Geneva and New York, national energy publications, information provided to the IEA Secretariat by national statistical offices as well as other unofficial Secretariat sources. Further information on coal used in non-OECD countries is published annually by the IEA in Energy Statistics and Balances of Non-OECD Countries. Also included in Part III are the Survey of Coal Ports world-wide and the Survey of Coal-fired Power Stations in coal-importing countries

  6. Coal resources of Indiana

    Spencer, Frank Darwyn

    1953-01-01

    The Indiana coal field forms the eastern edge of the eastern interior coal basin, which is near some of the most densely populated and highly productive manufacturing areas of the United States. (See fig. 1. ) For this reason Indiana coal reserves are an important State and National asset. In dollar value the coal mining industry is the largest of Indiana's natural-resource-producing industries. The total value of coil production for the year 1950 was more than 100 million dollars, or more than that of all other natural-resource industries in the State combined. As estimated herein, the original coal reserves of Indiana total 37,293 million tons, of which 27,320 million tons is contained in beds more than 42 inches thick; 7,632 million tons in beds 28 to 49. inches thick; and 2,341 million tons in beds 14 to 28 inches thick. The remaining reserves as of January 1951, total 35,806 million tons, of which 18,779 million tons is believed to be recoverable. The distribution of the reserves in these several categories is summarized by counties in table 1. Of the total original reserves of 37,293 million tons, 6,355 million tons can be classified as measured; 8,657 million tons as indicated; and 22,281 million tons as inferred. Strippable reserves constitute 3,524 million tons, or 9.5 percent of the total original reserves. The distribution of the strippable and nonstrippable original reserves is summarized in tables 2 and 3 by counties and by several categories, according to the thickness of the beds and the relative abundance and reliability of the information available for preparing the estimates. The distribution of the estimated 18,779 million tons of recoverable strippable and nonstrippable reserves in Indiana is further summarized by counties in table 4, and the information is presented graphically in figures 2 and 3. The tables i to 4 and figures 2 and 3 include beds in the 14- to 28-inch category, because thin beds have been mined in many places. However, many

  7. Study of Natural Radioactivity in Coal Samples of Baganuur Coal Mine, Mongolia

    Altangerel, M.; Norov, N.; Altangerel, D.

    2009-03-01

    Coal and soil samples from Baganuur Coal Mine (BCM) of Mongolia have been investigated. The activities of 226Ra, 232Th and 40K have been measured by gamma-ray spectrometry using shielded HPGe detector. Contents of natural radionuclide elements (U, Th and K) have been determined. Also the activities and contents of radionuclide of ashes were determined which generated in Thermal Power Plant ♯3 of Ulaanbaatar from coal supplied from BCM.

  8. FY 2000 report on the survey of the overseas geological structure. Japan-China joint coal exploration - Yu Xian project; 2000 nendo kaigai chishitsu kozo nado chosa hokokusho. Nippon Chugoku sekitan kyodo tansa Yu Xian project

    NONE

    2001-03-01

    The geological survey was carried out which is needed for coal mine design in the Yu Xian coal mine area, Yu Xian coal field, Hebei province, China. The term of survey was 5 years from 1996 to 2000. Activities are mainly for seismic survey and boring survey. Japan was in charge of the seismic survey, and China in charge of the boring survey. Both attained the goal. The results of the activities were summed up in the following 7 items: 1) outline of the survey; 2) general investigation; 3) state of the exploration related materials/machinery; 4) field survey; 5) items of survey; 6) results of the survey; 7) conclusion. In 6), the geological analysis, coal quality survey and coal amount survey were conducted. In the geological analysis, analyzed were the succession of strata, geological structure, and the situation of existence of coal seams. In 7), the following were made clear: geological structure of the survey area, coal seam, coal quality, hydrological geology, other conditions of drilling technology, and coal amount. The coal amount was 328.34 million tons in a total of A/B/C class coals. The total coal amount of Nos. 1 and 5 coal seams was 259.79 million tons, which was 79.1% of the total coal amount in all area. The average thickness of Nos. 1 and 5 coal seams, which are the main minable coal seams, was 3.10m and 2.66m, respectively. (NEDO)

  9. Methane Flux and Authigenic Carbonate in Shallow Sediments Overlying Methane Hydrate Bearing Strata in Alaminos Canyon, Gulf of Mexico

    Joseph P. Smith

    2014-09-01

    Full Text Available In June 2007 sediment cores were collected in Alaminos Canyon, Gulf of Mexico across a series of seismic data profiles indicating rapid transitions between the presence of methane hydrates and vertical gas flux. Vertical profiles of dissolved sulfate, chloride, calcium, magnesium, and dissolved inorganic carbon (DIC concentrations in porewaters, headspace methane, and solid phase carbonate concentrations were measured at each core location to investigate the cycling of methane-derived carbon in shallow sediments overlying the hydrate bearing strata. When integrated with stable carbon isotope ratios of DIC, geochemical results suggest a significant fraction of the methane flux at this site is cycled into the inorganic carbon pool. The incorporation of methane-derived carbon into dissolved and solid inorganic carbon phases represents a significant sink in local carbon cycling and plays a role in regulating the flux of methane to the overlying water column at Alaminos Canyon. Targeted, high-resolution geochemical characterization of the biogeochemical cycling of methane-derived carbon in shallow sediments overlying hydrate bearing strata like those in Alaminos Canyon is critical to quantifying methane flux and estimating methane hydrate distributions in gas hydrate bearing marine sediments.

  10. Coal in Asia-Pacific. Vo1 7, No. 1

    NONE

    1996-03-01

    In China, there are bottle-necks of the coal transportation capacity in the major inter-regional routes. The Chinese Government`s eighth and ninth five-year plans intend to increase the capacity. In the 9% growth case, the planned railway transport capacity will be critical. Measures are considered, as to promotion of coal dressing, transport as electric power, construction of nuclear power plants and hydraulic power plants, and construction of coal water slurry pipe lines. Japan`s coal policy includes the structural adjustment of coal mining industry, and a new policy for coal in the total energy policy. To secure the stable overseas coal supply, NEDO has a leading part in overseas coal resources development. Coal demand and supply, mining technology, mine safety, coal preparation and processing technology, and comprehensive coal utilization technology including clean coal technology in Japan are described. At present, Thailand is progressing with the seventh plan, and the development of domestic energy emphasize lignite, natural gas, and oil. Thai import demand for high-quality coal is to be increasing. Japan`s cooperation is considered to be effective for the environmental problems. 12 figs., 40 tabs.

  11. On-line nuclear analysis of coal (Nucoalyzer)

    Brown, D.R.; Gozani, T.; Bozorgmanesh, H.

    1980-01-01

    Control of quality in the coal process stream is increasingly important in both coal preparation facilities and coal fire power plants. Traditional wet chemistry methods of monitoring coal composition are incapable of providing anything approaching real-time analysis of coal. Typically, small samples of the coal stream are laboratory analyzed and the results made available between a day to a week later. By this time the coal is through the process stream, often already burned and no control is possible. The need of real-time analysis of bulk quantities of the coal has long been recognized and this need motivated Science Applications, Inc. to develop, since 1975, a continuous on-line nuclear analyzer of coal (or CONAC). Over the last three years a prototype of this instrument has undergone extensive testing using 200 pound bulk samples of a wide variety of US coal types. The Nucoalyzer has proven capable of measuring the abundances of all the important elemental constituents of coal along with the ash and calorific value. In the past year the first instrument has been installed and undergone testing at Detroit Edison's Monroe Coal blending facility, where it will control the blending of high and low sulfur coal to meet EPA emission regulations

  12. Trends in Japanese coal trade

    Nakajima, S

    1986-01-01

    The author discusses 1) the latest forecast for coal demand in Japan; 2) trends in Japanese steam coal demand, with breakdown by industry; 3) the organization of steam coal supply, with details of the distribution network and of the new coal cartridge system; 4) the demand for metallurgical coal. Other topics outlined include the current status of Japanese coal production, Japanese coal trade, and the development of overseas coal resources. 1 figure, 5 tables.

  13. Application of in-situ stress measurement on bursts disasters of rock and CO{sub 2} in coal mine

    Lian-Jie Wang; Dong-Sheng Sun; Li-Rong Zhang; Guan-Wu Zhou [Ministry of Land and Resources, Beijing (China)

    2009-01-15

    For the purpose of reduction and prevention of rock burst disasters and CO{sub 2}, measurements were made of in-situ stress and mechanical parameters of rock in Yingcheng mine. Geological structure and gas measurements were studied and the stress field was simulated and distribution of stress field was obtained in this area. On the basis of the study, the danger areas of rockbursts and CO{sub 2} were predicted. Preventive measures were suggested to decrease gas pressure and in-situ stress in front of the working face with advance boreholes relieving blasting. 12 refs., 5 figs., 1 tab.

  14. Studies on the Neogene Tertiary strata distributed in the central part of Tottori prefecture

    Yoshitani, Akihiko; Yoshizawa, Junko.

    1978-01-01

    The Neogene Tertiary strata, distributed in the central part of Tottori Prefecture, are volcano-stratigraphically classified, as shown in Figure 3. The Miocene strata are divided into Ojika formation and Mitoku formation in ascending order. Ojika formation, composed of plagio-rhyolitic pyroclastics and lavas, abuts against the basement rocks. Furthermore, some breaccias derived from the talus basal conglomerate beds are found in Ojika formation. Mitoku formation abuts both against the basement rocks and Ojika formation, and sometimes overlaps on the basement rocks. From the investigation into the Miocene strata, it is clarified that the depression took place prior to the volcanic activities at the earliest stage of the present Miocene sedimentary basin. (author)

  15. Coal Moisture Estimation in Power Plant Mills

    Andersen, Palle; Bendtsen, Jan Dimon; Pedersen, Tom S.

    2009-01-01

    Knowledge of moisture content in raw coal feed to a power plant coal mill is of importance for efficient operation of the mill. The moisture is commonly measured approximately once a day using offline chemical analysis methods; however, it would be advantageous for the dynamic operation...... of the plant if an on-line estimate were available. In this paper we such propose an on-line estimator (an extended Kalman filter) that uses only existing measurements. The scheme is tested on actual coal mill data collected during a one-month operating period, and it is found that the daily measured moisture...

  16. Mineralogical and lithochemical studies of strata beneath the Harwell research site

    Wilmot, R.D.; Morgan, D.J.

    1982-11-01

    Determinations have been made of the mineralogy and lithochemistry of the principal lithological units of the Mesozoic and Palaeozoic rocks penetrated by boreholes at the Harwell Research Site. Samples were taken at approximately 9m intervals from the Upper Greensand to the Coal Measures, together with a number from the Chalk. Mineralogical analyses were carried out using X-ray diffraction, with thermal analysis and surface area measurements aiding quantification. Major and trace element determinations were made using direct electron excitation X-ray spectrometry and X-ray fluorescence respectively. Other chemical determinations included organic carbon, sulphate and 'exchangeable' cations. The mineralogical and lithochemical variations within and between the major litho-stratigraphic units are discussed and compared with published data for other localities. (author)

  17. Determination of the stagnation point in pulverized coal swirl flames by detailed analysis of laser velocity measurements; Staupunktbestimmung in Kohlenstaub-Drallflammen mittels detaillierter Analyse von LDA-Daten

    Ohliger, A.; Stadler, H.; Foerster, M.; Kneer, R. [RWTH Aachen University (Germany). Lehrstuhl fuer Waerme- und Stoffuebertragung

    2009-07-01

    When Laser Doppler Anemometry (LDA) is used for experimental investigation of flow fields in pulverised coal flames, the measured coal particle velocities are usually averaged in order to determine the gas velocity. This paper shows that this approach can lead to a misinterpretation of the data. In the burner vicinity of the investigated flame, where high accelerations in the gas phase occur, a discrepancy appears between the measured velocity distribution and the expected normal distribution. Thus, a detailed analysis of the measured particle data is conducted and compared to conventional averaging. The difference can be attributed to large particles from the inner recirculation zone of the flame, which do not follow the gas flow properly. (orig.)

  18. Guangxi crustal structural evolution and the formation and distribution regularities of U-rich strata

    Kang Zili.

    1989-01-01

    Based on summing up Guangxi geotectonic features and evolutionary regularities, this paper discusses the occurrence features, formation conditions and time-space distribution regularities of various U-rich strata during the development of geosyncline, platform and diwa stages, Especially, during diwa stage all those U-rich strata might be reworked to a certain degree and resulted in the mobilization of uranium, then enriching to form polygenetic composite uranium ore deposits with stratabound features. This study will be helpful for prospecting in the region

  19. Nitrogen in Chinese coals

    Wu, D.; Lei, J.; Zheng, B.; Tang, X.; Wang, M.; Hu, Jiawen; Li, S.; Wang, B.; Finkelman, R.B.

    2011-01-01

    Three hundred and six coal samples were taken from main coal mines of twenty-six provinces, autonomous regions, and municipalities in China, according to the resource distribution and coal-forming periods as well as the coal ranks and coal yields. Nitrogen was determined by using the Kjeldahl method at U. S. Geological Survey (USGS), which exhibit a normal frequency distribution. The nitrogen contents of over 90% Chinese coal vary from 0.52% to 1.41% and the average nitrogen content is recommended to be 0.98%. Nitrogen in coal exists primarily in organic form. There is a slight positive relationship between nitrogen content and coal ranking. ?? 2011 Science Press, Institute of Geochemistry, CAS and Springer Berlin Heidelberg.

  20. Coal marketing manual 1986

    1986-01-01

    This manual presents information for the use of marketers, consumers, analysts and investors. The information is presented in a series of tables and figures. Statistics are given for: Australian export tonnages and average export values for 1978-1985; international pig iron production 1976 to 1985; and international crude steel production 1979 to 1985. Trends in Australian export tonnages and prices of coal are reviewed. Details of international loading and discharge ports are given, together with a historical summary of shipping freight-rates since 1982. Long term contract prices for thermal and coking coal to Japan are tabulated. A review of coal and standards is given, together with Australian standards for coal and coke. A section on coal quality is included containing information on consumer coal quality preferences and Australian and Overseas coal brands and qualities. Finally an index is given of contact details of Australian and Overseas exporting companies, government departments, and the Australian Coal Association.

  1. Coal worker's pneumoconiosis

    ... this page: //medlineplus.gov/ency/article/000130.htm Coal worker's pneumoconiosis To use the sharing features on this page, please enable JavaScript. Coal worker's pneumoconiosis (CWP) is a lung disease that ...

  2. Geology and fuel resources of the southern part of the San Juan Basin, New Mexico. Part 1, The coal field from Gallup eastward toward Mount Taylor, with a measured section of pre-Dakota(?) rocks near Navajo Church

    Sears, Julian D.

    1934-01-01

    member is split by the thick Hosta sandstone member, which toward the east and northeast is in turn split by the Satan tongue of the Mancos shale, of upper Niobrara (upper Colorado) age.In general the structure of the rocks is simple, showing a gentle northward dip into the San Juan Basin. At the west edge of the field the rocks dip steeply west in the north end of the prominent ridges known locally as the Hogback. In the eastern part there is a series of pronounced folds, whose crests and troughs retain the gentle basinward dip but whose limbs are steep monoclines that in places are faulted.The coal is of subbituminous rank and of fairly good grade. The coal beds are very irregular and lenticular. Those in the Gallup and Dilco members are of comparatively little importance, reaching a thickness of 4 to 5 feet in only a few places and, in general, being less than 3 feet thick. The coal beds of the Gibson, especially of its lower part, are more numerous and thicker, measurements of 4 to 6 feet thick being fairly common and one bed showing a thickness of 12 feet for more than a mile. No commercial mining has been undertaken in this field, but a few small mines have been used to supply trading posts and the Indian schools at Crown Point and Tohatchi.

  3. New approach for coal analysis

    1985-05-01

    The paper describes current progress of coal analysis and the existing problems. It focuses on the current major tasks of coal analysis, namely, to achieve three goals and to finish five tasks. Specific measures are mentioned, strengthening leadership and improvement of management, correct handling of three relations, i.e. relations between local and overall interests, between quantity and quality, and between rewards and punishments. The weak links should be improved i.e. the organization, the quality of the staff and the testing facilities should be improved. Finally, the paper says that improvement must be dependent on the progress of science and technology.

  4. Nuclear methods in coal research

    Lyon, W.S.

    1980-01-01

    Nuclear methods, particularly neutron activation analysis (NAA) provide useful information about elemental constituents in coal and fly ash, but often other techniques are required to supplement NAA data. Spark source mass spectrometry and atomic absorption have been studied as methods for determination of certain elements in coal that are not easily measured by NAA. In work concerned with the chemical speciation of elements in fly ash, a number of analytical techniques have been used; these include NAA, chemical etching and separation, optical and electron microscopy and x-ray diffraction

  5. The Middle Triassic megafossil flora of the Basin Creek Formation, Nymboida Coal Measures, New South Wales, Australia. Part 3. Fern-like foliage

    Holmes, W.B.K. [Noonee Nyrang, Wellington, NSW (Australia)

    2003-01-31

    Two quarries in the Basin Creek Formation of the Middle Triassic Nymboida Coal Measures have yielded numerous examples of fern-like foliage. No affiliated fertile material is available to place the fronds in a natural classification. Twenty three species in twelve genera are described as morpho-taxa in Order and Family Incertae Sedis. Plants described in this paper are: Cladophlebis conferta sp. nov., C octonerva sp. nov., C. paucinerva sp. nov., C. relallachfisp. nov., C. sinuala sp. nov., C. lenuoinnula sp. nov., Diconymba sparnosa gen. et sp. nov., Gouldianum alelhopleroides gen. et sp. nov., Leconama stachyophylla gen. et sp. nov., Micronymbopteris repens gen. et sp. nov., Nymbiella lacerata gen. et sp. nov., Nymboidiantum glossophyllum (Tenison-Woods) gen. et comb. nov., N. multilobatum gen. et sp. nov., N. elegans gen. et sp. nov., N. fractiflexum gen. et sp. nov., N. robustum gen. et sp. nov., Nymbophlebis polymorpha gen. et sp. nov., Nymbopteron dejerseyi (Retallack) gen. et comb. nov.,N. foleyi gen. et sp. nov., N. uncinatum gen. et sp. nov., Nymborhipteris radiata gen. et sp. nov., Ptilotonymba curvinervia gen. et sp. nov. and Sphenopteris speciosa sp. nov. The diversity of this new material demonstrates the remarkable recovery of Gondwana vegetation following the end-Permian extinction event.

  6. Radioactivity measurements in soils surrounding four coal-fired power plants in Serbia by gamma-ray spectrometry and estimated dose

    Vukašinović Ivana Ž.

    2014-01-01

    Full Text Available The study of spatial distribution of activity concentration of 238U, 226Ra, 210Pb, 232Th, 40K, and 137Cs radionuclides in the surface soil samples (n = 42 collected in the vicinity of four coal-fired power plants in Serbia is presented. Radioactivity measurements in soils performed by gamma-ray spectrometry showed values [Bqkg-1] in the range: 15-117 for 238U, 21-115 for 226Ra, 33-65 for 210Pb, 20-69 for 232Th, 324-736 for 40K, and 2-59 for 137Cs. Surface soil radio-activity that could have resulted from deposition of radionuclides from airborne discharges or resuspension of ash from disposal sites showed no enhanced levels. It was found that variation of soil textural properties, pH values, and carbonate content influenced activity levels of natural radionuclides while radiocesium activities were associated with soil organic matter content. Modification of some soil properties was observed in the immediate vicinity (<1 km of power plants where the soil was more alkaline with coarser particles (0.2-0.05 mm and carbonates accumulated. Calculated average values of the absorbed gamma dose rate and annual external effective dose originating from the terrestrial radionuclides were 69.4 nGy/h and 0.085 mSv, respectively. [Projekat Ministarstva nauke Republike Srbije, br. 4007: Studying climate change and its influence on the environment: impacts, adaptation and mitigation

  7. Initiative hard coal; Initiative Steinkohle

    Leonhardt, J.

    2007-08-02

    In order to decrease the import dependence of hard coal in the European Union, the author has submitted suggestions to the director of conventional sources of energy (directorate general for energy and transport) of the European community, which found a positive resonance. These suggestions are summarized in an elaboration 'Initiative Hard Coal'. After clarifying the starting situation and defining the target the presupposition for a better use of hard coal deposits as raw material in the European Union are pointed out. On that basis concrete suggestions for measures are made. Apart from the conditions of the deposits it concerns thereby also new mining techniques and mining-economical developments, connected with tasks for the mining-machine industry. (orig.)

  8. Mechanical characteristics of fully mechanized top-coal caving face and surrounding rock stress shell

    Xie Guang-xiang [Anhui University of Science and Technology, Huainan (China)

    2005-06-15

    The distribution of surrounding rock stress in fully mechanized top-coal caving (FMTC) face was fully researched by large-scale and non-linear three-dimensional numerical simulation and equivalent laboratory. The results show that, there is the structure that is made of macroscopical stress shell composed of high stress binds in overlying strata of FMTC face. Stress shell, which bears and pass load of overlying strata, is primary supporting body. The stress in skewback of stress shell forms abutment pressure of surrounding rock in vicinity of working face. Bond-beam structure lies in reducing zone under stress shell. It only bear partial burden of strata under stress shell. The uppermost mechanical characteristic of FMTC face is lying in the low stress area under stress shell. It is the essential cause of strata behaviors of FMTC face relaxation. On the basis of analyzing stress shell, the mechanical essence that top coal performs a function of bedding is demonstrated. 4 refs., 7 figs.

  9. Fording Canadian Coal Trust

    Popowich, J.; Millos, R. [Elk Valley Coal Corporation, Calgary, AB (Canada)

    2004-07-01

    This is the first of five slide/overhead presentations presented at the Fording Canadian Coal Trust and Tech Cominco Ltd. investor day and mine tour. The Fording Canadian Coal Trust is described. The Trust's assets comprise six Elk Valley metallurgical coal mines and six wollastonite operations (in the NYCO Group). Trust structure, corporate responsibility, organizational structure, reserves and resources, management philosophy, operating strategies, steel market dynamics, coal market, production expansion, sales and distribution are outlined. 15 figs., 5 tabs.

  10. Coal. [1987 and 1989

    1988-06-01

    Despite increases in recently negotiated coal prices in US dollar terms, unit export returns for Australian coal are expected to rise only marginally in 1988-89 due to the anticipated appreciation of the Australian dollar. Australian coal production is expected to recover in 1988-89, after falling in 1987-88. A table summarising coal statistics in 1985-87 is presented. 2 figs., 1 tab.

  11. Review biodepyritisation of coal

    Acharya, C.; Sukla, L.B.; Misra, V.N. [Regional Research Lab., Orissa (India)

    2004-01-01

    This review provides a detailed summary of the recent and past research activities in the area of biodesulfurisation of coal. It provides information about microorganisms important for biodesulfurisation of coal, with the emphasis on Thiobacillus ferrooxidans. The review presents an insight into various methods of desulfurisation of coal combining physical and biological methods. Also, there are discussions on coal structure, distribution, mechanism and kinetics of pyrite oxidation and jarosite precipitation. Finally, areas requiring further research are identified.

  12. Coal dust symposium

    1981-03-01

    This paper gives a report of the paper presented at the symposium held in Hanover on 9 and 10 February 1981. The topics include: the behaviour of dust and coal dust on combustion and explosion; a report on the accidents which occurred at the Laegerdorf cement works' coal crushing and drying plant; current safety requirements at coal crushing and drying plant; and coal crushing and drying. Four papers are individually abstracted. (In German)

  13. Coal world market

    Anon.

    1996-01-01

    A brief analysis of major tendencies in the world market of coal is presented. It is pointed out that recent years, by and large, were favourable for the development of the world coal industry. Prices for coal (both for power-grade and coking one) in 1995 after many years of depressive state increased by nearly 20 % and reached a maximum of the last decade. International coal trading continues to grow and the tendency may persist in the mext two years

  14. Inorganic Constituents in Coal

    Rađenović A.

    2006-02-01

    Full Text Available Coal contains not only organic matter but also small amounts of inorganic constituents. More thanone hundred different minerals and virtually every element in the periodic table have been foundin coal. Commonly found group minerals in coal are: major (quartz, pyrite, clays and carbonates,minor, and trace minerals. Coal includes a lot of elements of low mass fraction of the orderof w=0.01 or 0.001 %. They are trace elements connected with organic matter or minerals comprisedin coal. The fractions of trace elements usually decrease when the rank of coal increases.Fractions of the inorganic elements are different, depending on the coal bed and basin. A varietyof analytical methods and techniques can be used to determine the mass fractions, mode ofoccurrence, and distribution of organic constituents in coal. There are many different instrumentalmethods for analysis of coal and coal products but atomic absorption spectroscopy – AAS is theone most commonly used. Fraction and mode of occurrence are one of the main factors that haveinfluence on transformation and separation of inorganic constituents during coal conversion.Coal, as an important world energy source and component for non-fuels usage, will be continuouslyand widely used in the future due to its relatively abundant reserves. However, there is aconflict between the requirements for increased use of coal on the one hand and less pollution onthe other. It’s known that the environmental impacts, due to either coal mining or coal usage, canbe: air, water and land pollution. Although, minor components, inorganic constituents can exert asignificant influence on the economic value, utilization, and environmental impact of the coal.

  15. PENENTUAN TITIK-TITIK BATAS OPTIMUM STRATA PADA PENARIKAN CONTOH ACAK BERLAPIS DENGAN PEMROGRAMAN DINAMIK (Kasus : Pengeluaran per Kapita Propinsi Jawa Timur Tahun 2008)

    Mahyudi Mahyudi

    2015-01-01

    Optimum stratification is the method of choosing the best boundaries that make strata internally homogeneous, given some sample allocation. In order to make the strata internally homogenous, the strata should be constructed in such a way that the strata variances for the characteristic under study be as small as possible. This could be achieved effectively by having the distribution of the main study variable known and create strata by cutting the range of the distribution at suitable points....

  16. Hard coal; Steinkohle

    Loo, Kai van de; Sitte, Andreas-Peter [Gesamtverband Steinkohle e.V., Herne (Germany)

    2013-04-01

    The year 2012 benefited from a growth of the consumption of hard coal at the national level as well as at the international level. Worldwide, the hard coal still is the number one energy source for power generation. This leads to an increasing demand for power plant coal. In this year, the conversion of hard coal into electricity also increases in this year. In contrast to this, the demand for coking coal as well as for coke of the steel industry is still declining depending on the market conditions. The enhanced utilization of coal for the domestic power generation is due to the reduction of the nuclear power from a relatively bad year for wind power as well as reduced import prices and low CO{sub 2} prices. Both justify a significant price advantage for coal in comparison to the utilisation of natural gas in power plants. This was mainly due to the price erosion of the inexpensive US coal which partly was replaced by the expansion of shale gas on the domestic market. As a result of this, the inexpensive US coal looked for an outlet for sales in Europe. The domestic hard coal has continued the process of adaptation and phase-out as scheduled. Two further hard coal mines were decommissioned in the year 2012. RAG Aktiengesellschaft (Herne, Federal Republic of Germany) running the hard coal mining in this country begins with the preparations for the activities after the time of mining.

  17. Coal economics and taxation

    1978-01-01

    These proceedings contain opening remarks, the luncheon and dinner addresses, list of delegates and the papers presented at the four sessions on Coal Mines cost money - for what.; Coal mines cost money - Where the money comes from; taxation and royalty policies; and the coal industry view on operating costs. Sixteen papers are abstracted separately.

  18. Demographic variables in coal miners’ safety attitude

    Yin, Wen-wen; Wu, Xiang; Ci, Hui-Peng; Qin, Shu-Qi; Liu, Jia-Long

    2017-03-01

    To change unsafe behavior through adjusting people’s safety attitudes has become an important measure to prevent accidents. Demographic variables, as influential factors of safety attitude, are fundamental and essential for the research. This research does a questionnaire survey among coal mine industry workers, and makes variance analysis and correlation analysis of the results in light of age, length of working years, educational level and experiences of accidents. The results show that the coal miners’ age, length of working years and accident experiences correlate lowly with safety attitudes, and those older coal miners with longer working years have better safety attitude, as coal miners without experiences of accident do.However, educational level has nothing to do with the safety attitude. Therefore, during the process of safety management, coal miners with different demographic characteristics should be put more attention to.

  19. An index to measure depreciation in air quality in some coal mining areas of Korba industrial belt of Chhattisgarh, India.

    Singh, Gurdeep

    2006-11-01

    The comparison with National Ambient Air Quality Standards does not always depict a true picture of the Air Quality Status of a study area. As an alternative an index that measures depreciation in Air Quality on more realistic terms has been proposed and applied to the ambient air monitoring data collected from some areas of Korba Coalfields in India. Results have been discussed in detail to illustrate the application of the proposed index and utility in bringing out more realistic air quality assessment.

  20. Active and passive measurements of radon/thoron exhalation from coal and flyash samples collected from various thermal power plants of Delhi, India

    Singh, Lalit Mohan; Kumar, Rajesh; Sahoo, B.K.; Sapra, B.K.; Rajendra Prasad

    2013-01-01

    Measurement of radon ( 222 Rn) exhalation from coal, flyash and soil samples was carried out using active (Scintillation based Smart Radon Monitor) as well as passive technique (SSNTD based Can technique). In addition, thoron ( 220 Rn) exhalation measurements were also made for the above samples using Scintillation based Smart Thoron Monitor. To the best of our knowledge, thoron exhalation measurement is first of its kind in India. In this study, a total of 26 samples collected from Badarpur Thermal Power Station, Badarpur and Rajghat Power Station, Rajghat, Delhi were analysed. Thoron surface exhalation rate measured by Scintillation based Thoron Monitor for Badarpur Thermal Power Station varied from 327.8 Bq/m 2 /h to 874.2 Bq/m 2 /h and for Rajghat Thermal Power Station it varied from 176.0 Bq/m 2 /h to 781.1 Bq/m 2 /h. Similarly, the radon mass exhalation rate measured by active technique varied from 12.13 mBq/Kg/h to 118.08 mBq/Kg/h for the samples collected from Badarpur Thermal Power Station; while it varied from 15.00 Bq/Kg/h to 168.07 mBq/Kg/h for the samples collected from Rajghat Thermal Power station. On the other hand, result of measurements made by the conventional Can technique were significantly lower varying from 0.44 mBq/Kg/h to 2.34 mBq/Kg/h for Rajghat Thermal Power Station and from 0.78 mBq/Kg/h to 2.88 mBq/Kg/h for Badarpur Thermal Power Station. This vast variation in the results obtained by active and passive techniques is due to the fact that the active technique accounts for the effect of back-diffusion and possible leakage from the chamber in the process of least square fitting of exponential model while it is not so in the case of SSNTD based Can technique. In view of this, results of active technique are more reliable as compared to the passive technique. More importantly, there was no thoron interference in the radon measurement by the active technique. Further experiments are being carried out using controlled radon and thoron

  1. Investigation on the Influence of Abutment Pressure on the Stability of Rock Bolt Reinforced Roof Strata Through Physical and Numerical Modeling

    Kang, Hongpu; Li, Jianzhong; Yang, Jinghe; Gao, Fuqiang

    2017-02-01

    In underground coal mining, high abutment loads caused by the extraction of coal can be a major contributor to many rock mechanic issues. In this paper, a large-scale physical modeling of a 2.6 × 2.0 × 1.0 m entry roof has been conducted to investigate the fundamentals of the fracture mechanics of entry roof strata subjected to high abutment loads. Two different types of roof, massive roof and laminated roof, are considered. Rock bolt system has been taken into consideration. A distinct element analyses based on the physical modeling conditions have been performed, and the results are compared with the physical results. The physical and numerical models suggest that under the condition of high abutment loads, the massive roof and the laminated roof fail in a similar pattern which is characterized as vertical tensile fracturing in the middle of the roof and inclined shear fracturing initiated at the roof and rib intersections and propagated deeper into the roof. Both the massive roof and the laminated roof collapse in a shear sliding mode shortly after shear fractures are observed from the roof surface. It is found that shear sliding is a combination of tensile cracking of intact rock and sliding on bedding planes and cross joints. Shear sliding occurs when the abutment load is much less than the compressive strength of roof.

  2. Environmental problems in Russian coal industry

    Kharchenko, V.; Oumnov, V.

    1996-01-01

    The state of the Russian coal industry is complicated both economically and environmentally. Most mines are unprofitable. Several coal mines are intended to be closed. So, under existing conditions, coal mines are unable to give much attention to environmental protection problems. At the same time, coal mining is one of the most polluting industries. The main trends in this industry's negative influence upon the environment are: land spoilage and immobilization to lay out open-pit mines and mineral waste dump areas and tailing piles as well as with industrial waste water runoff; atmospheric pollution with the air coming from underground and substances blown off from dumps, hydrogeological regime intervention in coal mining areas, etc. One way to solve environmental problems in coal mining is a more rational utilization of the accompanying natural coal resources. Such measures make it possible to obtain complementary profits not only at the expense of reducing environmental destruction but producing new kinds of goods or services as well. Examples of similar solutions are solid mineral wastes utilization, underground space utilization, coal gas utilization and other issues

  3. Outlook for the Australian coal market

    Anon.

    1990-01-01

    A shortage of bituminous coal is now being witnessed on the world market, which stems from an increase in demand for it. The prices for bituminous coal, which have been increasing since 1988, will continue to rise in 1990. World coal production in 1989/1990 has been estimated by the Australian Bureau of Mineral Resources at 3,370 million tons, which is 50 million tons more than in the preceding year. Australian experts predict a doubling in world demand for coal by 2025. Many Australian coal mining companies, counting on the increased demand in the future, are taking measures to consolidate production and strengthen their financial base in order to accelerate development of new fields or expand production at existing mines. It is expected that the highest rates of growth in demand will be for power coal. Because of increased world production of steel the demand for coking coal will also rise, but the rates of growth will be much lower than for power coal

  4. Self-scrubbing coal

    Kindig, J.K.

    1992-01-01

    More than 502 million tons - 65 percent of all coal shipped to utilities in 1990 - were above 1.2 pounds of sulfur dioxide per million Btu. Most of the coal, even though cleaned in conventional coal preparation plants, still does not meet the emission limitation the Clean Air Act Amendments mandate for the year 2000. To cope with this fact, most utilities plan to switch to low sulfur (western U.S. or Central Appalachian) coal or install scrubbers. Both solutions have serous drawbacks. Switching puts local miners out of work and weakens the economy in the utility's service territory. Scrubbing requires a major capital expenditure by the utility. Scrubbers also increase the operating complexity and costs of the generating station and produce yet another environmental problem, scrubber sludge. Employing three new cost-effective technologies developed by Customer Coals International (CCl), most non-compliance coals east of the Mississippi River can be brought into year-2000 compliance. The compliance approach employed, depends upon the characteristics of the raw coal. Three types of raw coal are differentiated, based upon the amount of organic sulfur in the coals and the ease (or difficultly) of liberating the pyrite. They are: Low organic sulfur content and pyrite that liberates easily. Moderate organic sulfur content and pyrite that liberates easily. High organic sulfur content or the pyrite liberates with difficulty. In this paper examples of each type of raw coal are presented below, and the compliance approach employed for each is described. The names of the beneficiated coal products produced from each type of raw coal give above are: Carefree Coal, Self-Scrubbing Coal and Dry-Scrubbing Coal

  5. Australian Coal Company Risk Factors: Coal and Oil Prices

    M. Zahid Hasan; Ronald A. Ratti

    2014-01-01

    Examination of panel data on listed coal companies on the Australian exchange over January 1999 to February 2010 suggests that market return, interest rate premium, foreign exchange rate risk, and coal price returns are statistically significant in determining the excess return on coal companies’ stock. Coal price return and oil price return increases have statistically significant positive effects on coal company stock returns. A one per cent rise in coal price raises coal company returns ...

  6. Evaluation of the layering of rock strata and basement rock depth of ...

    The layering of rock strata and depth to the basement rocks of a Federal University Teaching Hospital premises in Northern Nigeria was investigated in this study with the aim of providing 2D geo-electrical resistivity images of the subsurface for geotechnical development using a modern and state-of-the-art field instrument, ...

  7. Palynology of uppermost Jurassic and lowermost Cretaceous strata in the Eastern Netherlands

    Burger, D.

    1965-01-01

    The present investigation is a systematical treatment of the sporomorphs from strata at the Jurassic-Cretaceous boundary in the eastern Netherlands Twente area, and an attempt to apply palynology to detailed stratigraphical study, by making use of quantitative pollen analyses. The rock samples used

  8. Identification of the Paleocene-Eocene boundary in coastal strata in the Otway Basin, Victoria, Australia

    Frieling, J.; Huurdeman, Emiel; Rem, Charlotte; Donders, T.H.; Pross, Jorg; Bohaty, Steven M.; Holdgate, Guy; Gallagher, Stephen; McGowran, Brian; Bijl, P.K.

    2018-01-01

    Detailed, stratigraphically well-constrained environmental reconstructions are available for Paleocene and Eocene strata at a range of sites in the southwest Pacific Ocean (New Zealand and East Tasman Plateau; ETP) and Integrated Ocean Discovery Program (IODP) Site U1356 in the south of the

  9. Oligocene terrestrial strata of northwestern Ethiopia : a preliminary report on paleoenvironments and paleontology

    Bonnie F. Jacobs; Neil Tabor; Mulugeta Feseha; Aaron Pan; John Kappelman; Tab Rasmussen; William Sanders; Michael Wiemann; Jeff Crabaugh; Juan Leandro Garcia Massini

    2005-01-01

    The Paleogene record of Afro-Arabia is represented by few fossil localities, most of which are coastal. Here we report sedimentological and paleontological data from continental Oligocene strata in northwestern Ethiopia. These have produced abundant plant fossils and unique assemblages of vertebrates, thus filling a gap in what is known of Paleogene interior Afro-...

  10. Coal Data: A reference

    1991-01-01

    The purpose of Coal Data: A Reference is to provide basic information on the mining and use of coal, an important source of energy in the United States. The report is written for a general audience. The goal is to cover basic material and strike a reasonable compromise between overly generalized statements and detailed analyses. The section ''Coal Terminology and Related Information'' provides additional information about terms mentioned in the text and introduces new terms. Topics covered are US coal deposits, resources and reserves, mining, production, employment and productivity, health and safety, preparation, transportation, supply and stocks, use, coal, the environment, and more. (VC)

  11. Characterization of Malaysian coals for carbon dioxide sequestration

    Abunowara, M.; Bustam, M. A.; Sufian, S.; Eldemerdash, U.

    2016-06-01

    Coal samples from Mukah-Balingian and Merit-Pila coal mines were characterized with ultimate, approximate, petrographic analysis, FT-IR spectra patterns, FESEM images and BET measurements to obtain information on the chemical composition and chemical structure in the samples. Two coal samples were obtained from Merit-Pila coal mine namely sample1 (S1) and sample2 (S2). The other two coal samples were obtained from Mukah-Balingian coal mine namely sample3 (S3) and sample4 (S4), Sarawak, Malaysia. The results of ultimate analysis show that coal S1 has the highest carbon percentage by 54.47%, the highest hydrogen percentage by 10.56% and the lowest sulfur percentage by 0.19% and the coal S4 has the highest moisture content by 31.5%. The coal S1 has the highest fixed carbon percentage by 42.6%. The coal S4 has BET surface area by 2.39 m2/g and Langmuir surface area by 3.0684 m2/g respectively. Fourier-Transform Infrared (FT-IR) spectroscopy analysis of all coal samples shows a presence of oxygen containing functional groups which considered are as active sites on coal surface. The oxygen functional groups are mainly carboxyl (-COOH), hydroxyl (-OH), alkyl (-CH, -CH2, -CH3), aliphatic (C-O-C stretching associated with -OH), amino (-NH stretching vibrations), (-NH stretching vibrations), aromatic (C=C), vinylic (C=C) and clay minerals. In all FE-SEM images of coal samples matrix, it can be seen that there are luminous and as non luminous features which refer to the existence of various minerals types distributed in the coal organic matrix. The bright luminosity is due to the presence of sodium, potassium or aluminium. According to petrographic analysis, all coal sample samples are range in vitrinite reflectance from 0.38% to 56% (VRr) are sub-bituminous coals.

  12. Stability tables for opencast mining of coal and sedimentary deposits in inclined seams. Abacos de estabilidad para mineria de carbon y sedimentaria a cielo abierto con capas inclinadas

    Ayala, F.J.; Granda, J.R.; Sarti, A.

    1985-01-01

    The six chapters of the book cover the following aspects of strata control in surface mining: design of opencast coal sites; parameters for the geomechanical design of opencast sites; methods for calculating slope stability; calculating the stability of spoil tips with a fractured cement base; calculation of stripping ratios; and stability tables.

  13. Pola Penghidupan Masyarakat di Daerah Perdesaan pada Strata Rumahtangga yang Berbeda

    Kationo Udin

    2016-10-01

    Full Text Available ABSTRAK Penelitian pola penghidupan di daerah perdesaan perlu dilakukan mengingat daerah perdesaan merupakan bagian integral dari wilayah pembangunan yang perlu mendapat perhatian pemeritah melalui berbagai kebijakan pemberdayaan masyarakat perdesaan dalam konteks pembangunan daerah perdesaan. Untuk itu penelitian ini bertujuan mengkaji (1 strategi penghidupan rumahtangga dan (2 faktor penentu, serta (3 menyusun arahan pengembangan strategi penghidupan yang efektif pada tiap strata ekonomi rumahtangga dalam rangka peningkatan pendapatan di lokasi penelitian. Penelitian ini mengambil lokasi di Desa Karang Jaya Kabupaten Buru dengan unit penelitian pada strata rumahtangga. Metode penelitian yang digunakan adalah metode survey dengan menggunakan kuisioner dan wawancara dalam pengambilan data. Dengan adanya strata rumahtangga maka Teknik sampel menggunakan stratifield random sampling dengan penentuan besar sampel secara proportional. Jumlah sampel strata ekonomi lemah 65 rumahtangga, strata ekonomi menengah 34 rumahtangga dan strata ekonomi kuat 6 rumahtangga. Analisa data dilakukan secara kua ntitatif dengan menggunakan tabel frekuensi dan tabel silang serta dilengkapi dengan indepth interview. Hasil penelitian menunjukkan bahwa strata rumahtangga ekonomi lemah sebagian besar menerapkan strategi pemanfaatan sumberdaya rumahtangga untuk meningkatkan hasil pertanian. Sementara strata rumahtangga ekonomi menengah menerapkan strategi pemanfaatan sumberdaya rumahtangga, diversifikasi pekerjaan dan optimalisasi hasil pertanian. Strata rumahtangga ekonomi kuat lebih fokus pada strategi investasi modal usaha. Adapun yang menjadi faktor penentu dalam penerapan strategi di atas adalah modal fisikal dan modal finansial yang berbeda dari segi dominasi kepemilikan pada tiap strata ekonomi. Untuk itu perlu adanya pengembangan strategi yang lebih efektif melalui peningkatan keahlian/ketrampilan anggota rumahtangga, membentuk kelompok tani/usaha kecil

  14. Coal and public perceptions

    Porter, R.C.

    1993-01-01

    The Department of Energy's (DOE) clean coal outreach efforts are described. The reason why clean coal technology outreach must be an integral part of coal's future is discussed. It is important that we understand the significance of these advances in coal utilization not just in terms of of hardware but in terms of public perception. Four basic premises in the use of coal are presented. These are: (1) that coal is fundamentally important to this nation's future; (2) that, despite premise number 1, coal's future is by no means assured and that for the last 10 years, coal has been losing ground; (3) that coal's future hinges on the public understanding of the benefits of the public's acceptance of advanced clean coal technology; and (4) hat public acceptance of clean coal technology is not going to be achieved through a nationwide advertising program run by the Federal government or even by the private sector. It is going to be gained at the grassroots level one community at a time, one plant at a time, and one referendum at a time. The Federal government has neither the resources, the staff, nor the mandate to lead the charge in those debates. What is important is that the private sector step up to the plate as individual companies and an individual citizens working one-one-one at the community level, one customer, one civic club, and one town meeting at a time

  15. Indonesian coal export potential

    Millsteed, Ch.; Jolly, L.; Stuart, R.

    1993-01-01

    Indonesia's coal mining sector is expanding rapidly. Much of the increase in coal production since the mid-1980s has been exported. Indonesian coal mining companies have large expansion programs and continuing strong export growth is projected for the remainder of the 1990s. The low mining costs of indonesian coal, together with proximity to Asian markets, mean that Indonesia is well placed to compete strongly with other thermal coal exporters and win market share in the large and expanding thermal coal market in Asia. However, there is significant uncertainty about the likely future level of Indonesia's exportable surplus of coal. The government's planned expansion in coal fired power generation could constrain export growth, while the ability of producers to meet projected output levels is uncertain. The purpose in this article is to review coal supply and demand developments in Indonesia and, taking account of the key determining factors, to estimate the level of coal exports from Indonesia to the year 2000. This time frame has been chosen because all currently committed mine developments are expected to be on stream by 2000 and because it is difficult to project domestic demand for coal beyond that year. 29 refs., 8 tabs., 7 figs

  16. Coal; Le charbon

    Teissie, J.; Bourgogne, D. de; Bautin, F. [TotalFinaElf, La Defense, 92 - Courbevoie (France)

    2001-12-15

    Coal world production represents 3.5 billions of tons, plus 900 millions of tons of lignite. 50% of coal is used for power generation, 16% by steel making industry, 5% by cement plants, and 29% for space heating and by other industries like carbo-chemistry. Coal reserves are enormous, about 1000 billions of tons (i.e. 250 years of consumption with the present day rate) but their exploitation will be in competition with less costly and less polluting energy sources. This documents treats of all aspects of coal: origin, composition, calorific value, classification, resources, reserves, production, international trade, sectoral consumption, cost, retail price, safety aspects of coal mining, environmental impacts (solid and gaseous effluents), different technologies of coal-fired power plants and their relative efficiency, alternative solutions for the recovery of coal energy (fuel cells, liquefaction). (J.S.)

  17. Washability of Australian coals

    Whitmore, R L

    1979-06-01

    Australian coals tend to be young in geological age and high in ash by world standards; preparation of the coal before marketing is almost universal. On the basis of float and sink data from 39 locations in the eastern Australian coalfields, the coals are place in four categories representing increasing difficulty in their washability characteristics. These seem to be related neither to the geological age nor the geographical position of the deposit and Hunter Valley coals, for example, span all categories. The influence of crushing on the washability of Australian coals is briefly considered and from limited data it is concluded to be appreciably smaller than for British or North American coals. A strategy for the float and sink analysis of Australian coals is proposed and the influence of washability characteristics on current trends in the selection of separating processes for coking and steaming products is discussed.

  18. Coal Transition in the Czech Republic. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

    Reckova, Dominika; Recka, Lukacs; Scasny, Milan

    2017-01-01

    This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. Content: History of coal production and coal reserves; Key features of the Czech economy; Fuel mix in the Czech Republic 1990 - 2014; Key features of coal sector in the Czech Republic after 1990; The use of coal in the Czech Republic and its possible replacement: A. Coal as source of Electricity, B. Coal as Heating source, C. Non - energy coal use; The state role in the coal sector after 1990 - mining limits; Measures to ease transition: Phasing-out of mining activities, Rehabilitation of environmentally damaged land, Programmes financing the remediation of ecological damage, Remediation of environmental damage caused by mining; Future outlook; Lessons learned; References; Annex

  19. Results of coalbed-methane drilling, Meadowfill Landfill, Harrison County, West Virginia: Chapter G.4 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Ruppert, Leslie F.; Trippi, Michael H.; Fedorko, Nick; Grady, William C.; Eble, Cortland F.; Schuller, William A.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    The U.S. Environmental Protection Agency funded drilling of a borehole (39.33889°N., 80.26542°W.) to evaluate the potential of enhanced coalbed-methane production from unminable Pennsylvanian coal beds at the Meadowfill Landfill near Bridgeport, Harrison County, W. Va. The drilling commenced on June 17, 2004, and was completed on July 1, 2004. The total depth of the borehole was 1,081 feet (ft) and contained 1,053.95 ft of Pennsylvanian coal-bearing strata, and 27.05 ft of Mississippian strata.

  20. CO2 Emission Factors for Coals

    P. Orlović-Leko

    2015-03-01

    Full Text Available Emission factors are used in greenhouse gas inventories to estimate emissions from coal combustion. In the absence of direct measures, emissions factors are frequently used as a quick, low cost way to estimate emissions values. Coal combustion has been a major contributor to the CO2 flux into the atmosphere. Nearly all of the fuel carbon (99 % in coal is converted to CO2 during the combustion process. The carbon content is the most important coal parameter which is the measure of the degree of coalification (coal rank. Coalification is the alteration of vegetation to form peat, succeeded by the transformation of peat through lignite, sub-bituminous, bituminous to anthracite coal. During the geochemical or metamorphic stage, the progressive changes that occur within the coal are an increase in the carbon content and a decrease in the hydrogen and oxygen content resulting in a loss of volatiles. Heterogeneous composition of coal causes variation in CO2 emission from different coals. The IPCC (Intergovernmental Panel on Climate Change has produced guidelines on how to produce emission inventories which includes emission factors. Although 2006 IPCC Guidelines provided the default values specified according to the rank of the coal, the application of country-specific emission factors was recommended when estimating the national greenhouse gas emissions. This paper discusses the differences between country-specific emission factors and default IPCC CO2 emission factors, EF(CO2, for coals. Also, this study estimated EF(CO2 for two different types of coals and peat from B&H, on the basis fuel analyses. Carbon emission factors for coal mainly depend on the carbon content of the fuel and vary with both rank and geographic origin, which supports the idea of provincial variation of carbon emission factors. Also, various other factors, such as content of sulphur, minerals and macerals play an important role and influence EF(CO2 from coal. Carbonate minerals

  1. Process for hydrogenating coal and coal solvents

    Shridharani, K.G.; Tarrer, A.R.

    1983-02-15

    A novel process is described for the hydrogenation of coal by the hydrogenation of a solvent for the coal in which the hydrogenation of the coal solvent is conducted in the presence of a solvent hydrogenation catalyst of increased activity, wherein the hydrogenation catalyst is produced by reacting ferric oxide with hydrogen sulfide at a temperature range of 260/sup 0/ C to 315/sup 0/ C in an inert atmosphere to produce an iron sulfide hydrogenation catalyst for the solvent. Optimally, the reaction temperature is 275/sup 0/ C. Alternately, the reaction can be conducted in a hydrogen atmosphere at 350/sup 0/ C.

  2. Process for hydrogenating coal and coal solvents

    Tarrer, Arthur R.; Shridharani, Ketan G.

    1983-01-01

    A novel process is described for the hydrogenation of coal by the hydrogenation of a solvent for the coal in which the hydrogenation of the coal solvent is conducted in the presence of a solvent hydrogenation catalyst of increased activity, wherein the hydrogenation catalyst is produced by reacting ferric oxide with hydrogen sulfide at a temperature range of 260.degree. C. to 315.degree. C. in an inert atmosphere to produce an iron sulfide hydrogenation catalyst for the solvent. Optimally, the reaction temperature is 275.degree. C. Alternately, the reaction can be conducted in a hydrogen atmosphere at 350.degree. C.

  3. Coal use and coal technology study (KIS)

    Kram, T.; Okken, P.A.; Gerbers, D.; Lako, P.; Rouw, M.; Tiemersma, D.N.

    1991-11-01

    The title study aims to assess the possible role for coal in the Netherlands energy system in the first decades of the next century and the part new coal conversion technologies will play under various conditions. The conditions considered relate to (sectoral) energy demand derived from national scenarios in an international context, to energy prices, to environmental constraints (acidification, solid waste management and disposal) and to the future role for nuclear power production. Targets for reduction of greenhouse gas emissions are not explicitly included, but resulting CO 2 emissions are calculated for each variant case. The part that coal can play in the Dutch energy supply is calculated and analyzed by means

  4. Earliest history of coal mining and grindstone quarrying at Joggins, Nova Scotia, and its implications for the meaning of the place name Joggins

    Falcon-Lang, H.J. [Bristol Univ., Bristol (United Kingdom). Dept. of Earth Sciences; London Univ., Egham (United Kingdom). Dept. of Earth Sciences

    2009-07-01

    The Joggins Section is a carboniferous succession located on the southeastern shore of the Bay of Fundy in Nova Scotia. The explorer Charles Lyell wrote about the Section's coal-bearing strata and extraordinary fossil forests in 1843. This paper reviewed earlier studies and literature related to the region in order to discuss coal mining and grindstone quarrying in the region in the late 1600s. Mineral exploration of the region began soon after French settlers arrived in 1604, and the earliest record of coal-mining occurred in 1639. References to the Joggins Section occurred in the diary of Samuel Pepys. Detailed maps from 1686 depict coastal outcrop belts of coal-bearing strata. Other records describe illicit trade of coal between Joggins and New England. A travelogue in 1731 described the mines and their location. A state-sponsored British coal mine was proposed in 1730. However, the venture was abandoned after attacks by angry local residents. Later studies of the region described the coal as being of inferior quality. The General Mining Association of Britain became lessees of all the mines and minerals in the province of Nova Scotia in 1827. However, several bootleg operations continued to mine the coals. It was concluded that a thriving grindstone industry in the region filled gaps in the local economy caused by the periods of mine closures. 93 refs., 15 figs.

  5. Earliest history of coal mining and grindstone quarrying at Joggins, Nova Scotia, and its implications for the meaning of the place name Joggins

    Falcon-Lang, H.J.; London Univ., Egham

    2009-01-01

    The Joggins Section is a carboniferous succession located on the southeastern shore of the Bay of Fundy in Nova Scotia. The explorer Charles Lyell wrote about the Section's coal-bearing strata and extraordinary fossil forests in 1843. This paper reviewed earlier studies and literature related to the region in order to discuss coal mining and grindstone quarrying in the region in the late 1600s. Mineral exploration of the region began soon after French settlers arrived in 1604, and the earliest record of coal-mining occurred in 1639. References to the Joggins Section occurred in the diary of Samuel Pepys. Detailed maps from 1686 depict coastal outcrop belts of coal-bearing strata. Other records describe illicit trade of coal between Joggins and New England. A travelogue in 1731 described the mines and their location. A state-sponsored British coal mine was proposed in 1730. However, the venture was abandoned after attacks by angry local residents. Later studies of the region described the coal as being of inferior quality. The General Mining Association of Britain became lessees of all the mines and minerals in the province of Nova Scotia in 1827. However, several bootleg operations continued to mine the coals. It was concluded that a thriving grindstone industry in the region filled gaps in the local economy caused by the periods of mine closures. 93 refs., 15 figs

  6. Coal consumption and economic growth in China

    Li, Raymond; Leung, Guy C.K.

    2012-01-01

    The aim of this paper is to re-examine the relationship between coal consumption and real GDP of China with the use of panel data. This paper applies modern panel data techniques to help shed light on the importance of the heterogeneity among different regions within China. Empirical analyses are conducted for the full panel as well as three subgroups of the panel. The empirical results show that coal consumption and GDP are both I(1) and cointegrated in all regional groupings. Heterogeneity is found in the GDP equation of the full panel. The regional causality tests reveal that the coal consumption–GDP relationship is bidirectional in the Coastal and Central regions whereas causality is unidirectional from GDP to coal consumption in the Western region. Thus, energy conservation measures will not adversely affect the economic growth of the Western region but such measures will likely encumber the economy of the Coastal and Central regions, where most of the coal intensive industries are concentrated. - Highlights: ► We investigate the relationship between coal consumption and GDP in China. ► Panel data are used to account for the potential heterogeneity across different regions. ► Bidirectional causality is found in the Eastern and Central regions. ► Unidirectional causality from GDP to coal consumption is found in the Western region.

  7. The history of the British coal industry. Volume 2, 1700-1830: the industrial revolution

    Flinn, M W; Stoker, D

    1984-01-01

    The history of the British coal industry from 1700 to 1830 is discussed in terms of the development of coal-mining, the ownership and management of collieries, technology, the transport of coal, capital, markets, the organization of coal marketing, the economics of mining, the organization of mining labor, wages and industrial relations, the mining community, and the coal industry and the economy. A glossary of mining terms is provided, along with definitions of weights and measures used in the period.

  8. Analysis of Co-Effects on Air Pollutants and CO2 Emissions Generated by End-of-Pipe Measures of Pollution Control in China’s Coal-Fired Power Plants

    Haijun Zhao

    2017-03-01

    Full Text Available China is now facing great challenges resulting from climate change and air pollution, driven by the processes of industrialization and urbanization. Greenhouse gas and air pollutant emissions produced by the coal-fired power industry represent approximately 70% of the total emissions in China’s industrial sector. In this study, 39 coal-fired power plants built in China between 2014 and 2015 were analyzed in regards to the co-effects oncarbon dioxide and air pollutant emissions generated directly and indirectly by end-of-pipe measures of pollution control. After completing the quantitative analysis with input data from 83units of power plants, we found that co-effects were positive only for air pollutant reductions through the implementation of desulfurization, denitrification, and dedusting measures, but co-effects were negative for carbon dioxide production because of the corresponding electricity use and chemical reactions that led to the increases in carbon dioxide emissions. We also performed an assessment of the synergistic coefficients to better understand the degree of co-effects. It will be important for researchers to take a comprehensive view of China’s coal-fired power plants and look for solutions that can maximize positive co-effects and achieve overall co-benefits of reductions in greenhouse gas emissions and air pollutants.

  9. Clean coal technologies

    Aslanyan, G.S.

    1993-01-01

    According to the World Energy Council (WEC), at the beginning of the next century three main energy sources - coal, nuclear power and oil will have equal share in the world's total energy supply. This forecast is also valid for the USSR which possesses more than 40% of the world's coal resources and continuously increases its coal production (more than 700 million tons of coal are processed annually in the USSR). The stringent environmental regulations, coupled with the tendency to increase the use of coal are the reasons for developing different concepts for clean coal utilization. In this paper, the potential efficiency and environmental performance of different clean coal production cycles are considered, including technologies for coal clean-up at the pre-combustion stage, advanced clean combustion methods and flue gas cleaning systems. Integrated systems, such as combined gas-steam cycle and the pressurized fluidized bed boiler combined cycle, are also discussed. The Soviet National R and D program is studying new methods for coal utilization with high environmental performance. In this context, some basic research activities in the field of clean coal technology in the USSR are considered. Development of an efficient vortex combustor, a pressurized fluidized bed gasifier, advanced gas cleaning methods based on E-beam irradiation and plasma discharge, as well as new catalytic system, are are presented. In addition, implementation of technological innovations for retrofitting and re powering of existing power plants is discussed. (author)

  10. Coal prices rise

    McLean, A.

    2001-01-01

    Coking and semi hard coking coal price agreements had been reached, but, strangely enough, the reaching of common ground on semi soft coking coal, ultra low volatile coal and thermal coal seemed some way off. More of this phenomenon later, but suffice to say that, traditionally, the semi soft and thermal coal prices have fallen into place as soon as the hard, or prime, coking coal prices have been determined. The rise and rise of the popularity of the ultra low volatile coals has seen demand for this type of coal grow almost exponentially. Perhaps one of the most interesting facets of the coking coal settlements announced to date is that the deals appear almost to have been preordained. The extraordinary thing is that the preordination has been at the prescience of the sellers. Traditionally, coking coal price fixing has been the prerogative of the Japanese Steel Mills (JSM) cartel (Nippon, NKK, Kawasaki, Kobe and Sumitomo) who presented a united front to a somewhat disorganised force of predominantly Australian and Canadian sellers. However, by the time JFY 2001 had come round, the rules of the game had changed

  11. South Blackwater Coal`s maintenance program

    Nash, J. [South Blackwater Coal Limited, Blackwater, Qld. (Australia)

    1998-09-01

    The South Blackwater operation consists of two opencut mining areas and two underground mines (Laleham and Kenmure) near Blackwater in central Queensland, all of which supply coal to a central coal preparation plant. South Blackwater Coal Ltd. recently developed a maintenance improvement programme, described in this article. The programme involved implementation systems of key performance indicators (KPIs), benchmaking, condition monitoring, work planning and control, failure analysis and maintenance audit. Some improvements became almost immediately apparent, others were quite gradual. Major results included: improved availability (and reliability) of all opencast fleets, improvements in rear dump availability; reduced maintenance man-hours for opencast fleets; and increased availability of the coal handling and preparation plant. The paper is an edited version of that presented at the `Maintenance in mining conference` 16-19 March 1998, held in Bali, Indonesia. 4 figs., 2 photos.

  12. Cancer fear over coal tar products

    NONE

    1995-01-01

    Discusses a report by Dutch researchers which suggests that the regular use of coal tar shampoos may significantly increase the risk of cancer due to the high levels of polynuclear aromatic hydrocarbons (PAHs) in the products. The PAH exposure of volunteers using a coal tar anti-dandruff shampoo was studied by measuring the amount of hydroxypyrene, a PAH breakdown product in their urine. Volunteers who had used the shampoo excreted high levels of hydroxypyrene the day after exposure. Excretion by the control group using a non-coal tar anti-dandruff shampoo remained constant. 1 ref., 1 fig.

  13. Full-scale ash deposition measurements at Avedøre Power Plant unit 2 during suspension-firing of wood with and without coal ash addition

    Wu, Hao; Shafique Bashir, Muhammad; Jensen, Peter Arendt

    The formation of deposits during suspension-firing of wood at Avedøre Power Plant unit 2 (AVV2) was studied by using an advanced deposit probe system. The tests were conducted both with and without coal ash addition, and at two different locations with flue gas temperatures of 1250-1300 oC and 750...... with a high flue gas temperature of 1250-1300 oC, although the addition of coal fly ash increased the differential deposit formation rate (DDF-rate) and the ash deposition propensity, the deposit removal frequency were considerably increased and the major shedding mechanism was changed from soot...... corrosion. At the location with a low flue gas temperature of 750-800 oC, the addition of coal fly ash reduced the ash deposition propensity and caused the formed deposits being easily removable. Moreover, the KCl and KOH/K2CO3 found in the low-temperature deposits without coal ash addition disappeared when...

  14. Development of tools for managing the impacts on surface due to changing hydrological regimes surrounding closed underground coal mines (ECSC Coal RTD programme, contract 7220-PR-136)

    Veschkens, M.; Unland, W.; Kories, H.

    2005-01-01

    This paper demonstrates how box model approach and FE and box mixed model approach allow to better understand and model water flows in complex mined coal measures and interactions between shallow aquifers and flooded coal measures. Benefits of these approaches are illustrated on the basis of case studies in Liege and Ruhr coal basins. (authors)

  15. Development of tools for managing the impacts on surface due to changing hydrological regimes surrounding closed underground coal mines (ECSC Coal RTD programme, contract 7220-PR-136)

    Veschkens, M. [ISSeP, Liege (Belgium); Unland, W.; Kories, H. [DMT, Am Technologiepark, Essen (Germany)

    2005-07-01

    This paper demonstrates how box model approach and FE and box mixed model approach allow to better understand and model water flows in complex mined coal measures and interactions between shallow aquifers and flooded coal measures. Benefits of these approaches are illustrated on the basis of case studies in Liege and Ruhr coal basins. (authors)

  16. Coal comes clean

    Minchener, A.

    1991-01-01

    Coal's status as the dominant fuel for electricity generation is under threat because of concern over the environmental impacts of acid rain and the greenhouse effect. Sulphur dioxide and nitrogen oxides cause acid rain and carbon dioxide is the main greenhouse gas. All are produced when coal is burnt. Governments are therefore tightening the emission limits for fossil-fuel power plants. In the United Kingdom phased reductions of sulphur dioxide and nitrogen oxides emissions are planned. It will be the responsibility of the power generator to take the necessary steps to reduce the emissions. This will be done using a number of technologies which are explained and outlined briefly - flue gas desulfurization, separation of coal into high and low-sulphur coal, direct desulfurization of coal, circulating fluidised bed combustion, integrated-gasification combined cycle systems and topping cycles. All these technologies are aiming at cleaner, more efficient combustion of coal. (UK)

  17. Cuttability of coal

    Sikora, W

    1978-01-01

    The process of cutting dull M, dull bright MB, bright dull BM, and bright B coal under various compressive stress conditions was studied in laboratory tests. The efficiency of ploughs depends much more on the natural mining conditions than does that of shearer-loaders. For seams of medium workability, it is difficult to forecast whether ploughs will be successful. Cuttability tests are a good way of determining whether ploughs can be used. The effort necessary to cut coal in a stressed condition depends not only on such properties as the workability defined by the Protodyakonov index or compressive strength, but also, and mainly, on the petrographic structure and elastic properties of the coal. In bright coals with high elastic strain, and with BM and MB coals, a much greater increment of effort is necessary with increase in compressive stresses. The cuttability of dull coals from difficult mines was not very different.

  18. Coal tar in dermatology

    Roelofzen, J.H.J.; Aben, K.K.H.; Van Der Valk, P.G.M.; Van Houtum, J.L.M.; Van De Kerkhof, P.C.M.; Kiemeney, L.A.L.M. [Radboud University Nijmegen Medical Center, Nijmegen (Netherlands). Dept. of Dermatology

    2007-07-01

    Coal tar is one of the oldest treatments for psoriasis and eczema. It has anti-inflammatory, antibacterial, antipruritic and antimitotic effects. The short-term side effects are folliculitis, irritation and contact allergy. Coal tar contains carcinogens. The carcinogenicity of coal tar has been shown in animal studies and studies in occupational settings. There is no clear evidence of an increased risk of skin tumors or internal tumors. Until now, most studies have been fairly small and they did not investigate the risk of coal tar alone, but the risk of coal tar combined with other therapies. New, well-designed, epidemiological studies are necessary to assess the risk of skin tumors and other malignancies after dermatological use of coal tar.

  19. Coal-to-liquid

    Cox, A.W.

    2006-03-15

    With crude oil prices rocketing, many of the oil poor, but coal rich countries are looking at coal-to-liquid as an alternative fuel stock. The article outlines the two main types of coal liquefaction technology: direct coal liquefaction and indirect coal liquefaction. The latter may form part of a co-production (or 'poly-generation') project, being developed in conjunction with IGCC generation projects, plus the production of other chemical feedstocks and hydrogen. The main part of the article, based on a 'survey by Energy Intelligence and Marketing Research' reviews coal-to-liquids projects in progress in the following countries: Australia, China, India, New Zealand, the Philippines, Qatar and the US. 2 photos.

  20. Coal, culture and community

    NONE

    1993-11-01

    16 papers are presented with the following titles: the miners; municipalisation and the millenium - Bolton-upon-Dearne Urban District Council 1899-1914; the traditional working class community revisited; the cultural capital of coal mining communities; activities, strike-breakers and coal communities; the limits of protest - media coverage of the Orgreave picket during the miners` strike; in defence of home and hearth? Families, friendships and feminism in mining communities; young people`s attitudes to the police in mining communities; the determinants of productivity growth in the British coal mining industry, 1976-1989; strategic responses to flexibility - a case study in coal; no coal turned in Yorkshire?; the North-South divide in the Central Coalfields; the psychological effects of redundancy and worklessness - a case study from the coalfields; the Dearne Valley initiative; the future under labour: and coal, culture and the community.

  1. Mercury concentrations in pond fish in relation to a coal-fired power plant

    Logan, D.T.; Wilson, H.T.; Pinkney, A.E.

    1994-01-01

    Although many studies have reported that atmospheric mercury is the primary cause for bioaccumulation in fish from remote lakes, few data are available on the effects of possible near-field deposition on fish from nearby waters. The authors surveyed mercury concentrations in fish from 23 ponds in the vicinity of the coal-burning Dickerson Power Plant (Dickerson, MD). A stratified random sampling design was used to select ponds within zones delineated by concentric rings mapped at 3, 7, 10, and 15 km from the plant. For each pond, mercury concentrations were measured by cold vapor atomic absorption spectrometry in sunfish (bluegill, pumpkin seed, or green sunfish), and largemouth bass, which were present in 14 of the ponds. Mean concentrations in the ponds ranged from 0.03 to 0.38 ppm for sunfish and from 0.04 to 0.43 ppm for bass. Alkalinity, pH, conductivity, hardness, and fish length were measured. Stepwise multiple regression identified variables related to tissue concentrations. Differences between strata were tested with ANCOVA. The pattern of concentrations was compared to the pattern of wet deposition predicted by a model. The predicted pattern of local wet deposition did not match the observed pattern of mercury bioaccumulation. This research was sponsored by the Maryland Department of Natural Resources, Power Plant Research Program

  2. Paleocurrents of the Middle-Upper Jurassic strata in the Paradox Basin, Colorado, inferred from anisotropy of magnetic susceptibility (AMS)

    Ejembi, J. I.; Ferre, E. C.; Potter-McIntyre, S. L.

    2017-12-01

    The Middle-Upper Jurassic sedimentary strata in the southwestern Colorado Plateau recorded pervasive eolian to fluvio-lacustrine deposition in the Paradox Basin. While paleocurrents preserved in the Entrada Sandstone, an eolian deposition in the Middle Jurassic, has been well constrained and show a northwesterly to northeasterly migration of ergs from the south onto the Colorado Plateau, there is yet no clear resolution of the paleocurrents preserved in the Wanakah Formation and Tidwell Member of the Morrison Formation, both of which are important sedimentary sequences in the paleogeographic framework of the Colorado Plateau. New U-Pb detrital zircon geochronology of sandstones from these sequences suggests that an abrupt change in provenance occurred in the early Late Jurassic, with sediments largely sourced from eroding highlands in central Colorado. We measured the anisotropy of magnetic susceptibility (AMS) of sediments in oriented sandstone samples from these three successive sequences; first, to determine the paleocurrents from the orientations of the AMS fabrics in order to delineate the source area and sediments dispersal pattern and second, to determine the depositional mechanisms of the sediments. Preliminary AMS data from two study sites show consistency and clustering of the AMS axes in all the sedimentary sequences. The orientations of the Kmin - Kint planes in the Entrada Sandstone sample point to a NNE-NNW paleocurrent directions, which is in agreement with earlier studies. The orientations of the Kmin - Kint planes in the Wanakah Formation and Tidwell Member samples show W-SW trending paleocurrent directions, corroborating our hypothesis of a shift in provenance to the eroding Ancestral Front Range Mountain, located northeast of the Paradox Basin, during the Late Jurassic. Isothermal remanence magnetization (IRM) of the samples indicate that the primary AMS carriers are detrital, syndepositional ferromagnetic minerals. Thus, we contend that AMS can

  3. Coal contract cost reduction through resale of coal

    Simon, R.

    1990-01-01

    The weak coal market of the 1980's has enabled utilities and other users of coal to enjoy stable or falling prices for coal supplies. Falling prices for coal stimulated the renegotiation of numerous coal contracts in recent years, as buyers look to take advantage of lower fuel prices available in the marketplace. This paper examines the use of coal resale transactions as a means of reducing fuel costs, and analyzes the benefits and risks associated with such transactions

  4. Evaluation of the ignition behaviour of coals and blends

    J. Faundez; F. Rubiera; X. Garcia; A. Arenillas; A.L. Gordon; J.J. Pis [CSIC, Instituto Nacional del Carbon, Oviedo (Spain). Department of Energy and Environment

    2003-07-01

    An experimental study about ignition of coals and blends was carried out by using an entrained flow reactor (EFR) with continuous feed. Seven coals of varying rank, from subbituminous to semianthracite, were tested and evolving gases (O{sub 2}, CO, CO{sub 2}, NO) were measured. The ignition temperature was evaluated from the evolution profiles of these gases, and correlated inversely to the reactivity of coals, as reflected by increasing values of ignition temperatures in the sequence subbituminous, high volatile bituminous, low volatile bituminous and semianthracite coals. Mechanism of ignition varied from an heterogeneous mechanism (for subbituminous, low volatile bituminous and semianthracite coals) to an homogeneous mechanism (for high volatile bituminous coal). Experiments with coal blends showed that if a low volatile bituminous coal is blended with a high volatile bituminous coal, the latter determines the value of the ignition temperature and ignition mechanism of the blend, when its percentage in the blend is 50% or higher. For blends of subbituminous and high volatile bituminous coals, the ignition mechanism of the blend is determined by the ignition mechanism of the coal with a higher content in the blend. 12 refs., 9 figs., 1 tab.

  5. Further Investigations on Simultaneous Ultrasonic Coal Flotation

    Safak Gokhan Ozkan

    2017-09-01

    Full Text Available This study investigates the flotation performance of a representative hard coal slime sample (d80 particle size of minus 0.2 mm obtained from the Prosper-Haniel coal preparation plant located in Bottrop, Germany. Flotation was carried out with a newly designed flotation cell refurbished from an old ultrasonic cleaning bath (2.5 L volume equipped with a single frequency (35 kHz and two different power levels (80–160 W and a sub-aeration-type flotation machine operating at a stable impeller speed (1200 rpm and air rate (2.5 L/min. The reagent combination for conventional and simultaneous ultrasonic coal flotation tests was Ekofol-440 at variable dosages (40–300 g/t with controlling water temperature (20–25 °C at natural pH (6.5–7.0. The batch coal flotation results were analyzed by comparing the combustible recovery (% and separation efficiency (% values, taking mass yield and ash concentrations of the froths and tailings into account. It was found that simultaneous ultrasonic coal flotation increased yield and recovery values of the floated products with lower ash values than the conventional flotation despite using similar reagent dosages. Furthermore, particle size distribution of the ultrasonically treated and untreated coals was measured. Finely distributed coal particles seemed to be agglomerated during the ultrasonic treatment, while ash-forming slimes were removed by hydrodynamic cavitation.

  6. Marketing Canada's coal

    1985-11-01

    The topics are presented which were discussed at the 36th Canadian Coal Conference, held in Vancouver, BC in September 1985. The theme was Challenges, today and tomorrow and the conference sought to examine the primary problems confronting the world coal industry today: overcapacity, soft demand, depressed prices and intense global competition. Coal production in Canada was presented and its role in the steelmaking and electric power industries evaluated. A general mood of optimism prevailed.

  7. Coal transportation road damage

    Burtraw, D.; Harrison, K.; Pawlowski, J.A.

    1994-01-01

    Heavy trucks are primarily responsible for pavement damage to the nation's highways. In this paper we evaluate the pavement damage caused by coal trucks. We analyze the chief source of pavement damage (vehicle weight per axle, not total vehicle weight) and the chief cost involved (the periodic overlay that is required when a road's surface becomes worn). This analysis is presented in two stages. In the first section we present a synopsis of current economic theory including simple versions of the formulas that can be: used to calculate costs of pavement wear. In the second section we apply this theory to a specific example proximate to the reference environment for the Fuel Cycle Study in New Mexico in order to provide a numerical measure of the magnitude of the costs

  8. Dynamics on strata of trigonal Jacobians and some integrable problems of rigid body motion

    Braden, H W; Enolski, V Z; Fedorov, Yu N

    2013-01-01

    We present an algebraic geometrical and analytical description of the Goryachev case of rigid body motion. It belongs to a family of systems sharing the same properties: although completely integrable, they are not algebraically integrable, their solution is not meromorphic in the complex time and involves dynamics on the strata of the Jacobian varieties of trigonal curves. Although the strata of hyperelliptic Jacobians have already appeared in the literature in the context of some dynamical systems, the Goryachev case is the first example of an integrable system whose solution involves a more general curve. Several new features (and formulae) are encountered in the solution given in terms of sigma-functions of such a curve. (paper)

  9. The Strata-1 Regolith Dynamics Experiment: Class 1E Science on ISS

    Fries, Marc; Graham, Lee; John, Kristen

    2016-01-01

    The Strata-1 experiment studies the evolution of small body regolith through long-duration exposure of simulant materials to the microgravity environment on the International Space Station (ISS). This study will record segregation and mechanical dynamics of regolith simulants in a microgravity and vibration environment similar to that experienced by regolith on small Solar System bodies. Strata-1 will help us understand regolith dynamics and will inform design and procedures for landing and setting anchors, safely sampling and moving material on asteroidal surfaces, processing large volumes of material for in situ resource utilization (ISRU) purposes, and, in general, predicting the behavior of large and small particles on disturbed asteroid surfaces. This experiment is providing new insights into small body surface evolution.

  10. Application of stable isotopes to hydrogeology in coal mine

    Duan Qi; Duan Yucheng

    1988-01-01

    Stable isotopes including Oxygen-18 and Deuterium have been applied to investigation of hydrogeology in main coal mines. By determination of stable isotopic composition of hydrogen and oxygen together with water analysis, the following studies have been developed: Identification of the hydrogeochemical characteristics of the groundwater from varied aquifers; Analysis of the hydraulic relationship between varied aquifers; Interpretation of the probable recharge source of mine water. The research results mentioned above reveal that: 1. The groundwater from main aquifers at coal mines in north China is of meteoric origin, which is recharged from hilly area surrounding the coal mine. Its isotopic composition differs slightly from that of the local precipitation. 2. There is a mutual hydraulic relationship between the Ordovician and Quarternary aquifers, so the difference of isotopic composition is very small. 3. By way of the variation of isotopic composition of groundwater from coal-bearing strata, we can infer the hydraulic relationship extent between overlaid alluvial layer and underlaid Ordovician limestone. (author). 9 refs, 6 figs, 8 tabs

  11. Coal export facilitation

    Eeles, L.

    1998-01-01

    There is a wide range of trade barriers, particularly tariffs, in current and potential coal market. Commonwealth departments in Australia play a crucial role in supporting government industry policies. This article summarises some of more recent activities of the Department of Primary Industries and Energy (DPIE) in facilitating the export of Australian Coals. Coal export facilitation activities are designed to assist the Australian coal industry by directing Commonwealth Government resources towards issues which would be inappropriate or difficult for the industry to address itself

  12. Optimal coal import strategy

    Chen, C.Y.; Shih, L.H.

    1992-01-01

    Recently, the main power company in Taiwan has shifted the primary energy resource from oil to coal and tried to diversify the coal supply from various sources. The company wants to have the imported coal meet the environmental standards and operation requirements as well as to have high heating value. In order to achieve these objectives, establishment of a coal blending system for Taiwan is necessary. A mathematical model using mixed integer programming technique is used to model the import strategy and the blending system. 6 refs., 1 tab

  13. Electrostatic beneficiation of coal

    Mazumder, M.K.; Tennal, K.B.; Lindquist, D.

    1994-10-01

    Dry physical beneficiation of coal has many advantages over wet cleaning methods and post combustion flue gas cleanup processes. The dry beneficiation process is economically competitive and environmentally safe and has the potential of making vast amounts of US coal reserves available for energy generation. While the potential of the electrostatic beneficiation has been studied for many years in laboratories and in pilot plants, a successful full scale electrostatic coal cleaning plant has not been commercially realized yet. In this paper the authors review some of the technical problems that are encountered in this method and suggest possible solutions that may lead toward its full utilization in cleaning coal.

  14. Geology and coal resources of the Hanging Woman Creek Study Area, Big Horn and Powder River Counties, Montana

    Culbertson, William Craven; Hatch, Joseph R.; Affolter, Ronald H.

    1978-01-01

    In an area of 7,200 acres (29 sq km) In the Hanging Woman Creek study area, the Anderson coal bed contains potentially surface minable resources of 378 million short tons (343 million metric tons) of subbituminous C coal that ranges in thickness from 26 to 33 feet (7.9-10.1 m) at depths of less than 200 feet (60 m). Additional potentially surface minable resources of 55 million short tons (50 million metric tons) are contained in the 9-12 foot (2.7-3.7 m) thick Dietz coal bed which lies 50-100 feet (15-30 m) below the Anderson. Analyses of coal from 5 core holes indicates that the Anderson bed contains 0.4 percent sulfur, 5 percent ash, and has a heating value of 8,540 Btu/lb (4,750 Kcal/kg). The trace element content of the coal is generally similar to other coals in the Powder River Basin. The two coal beds are in the Fort Union Formation of Paleocene age which consists of sandstone, siltstone, shale, coal beds, and locally impure limestone. A northeast-trending normal fault through the middle of the area, downthrown on the southeast side, has displaced the generally flat lying strata as much as 300 feet (91 m). Most of the minable coal lies northwest of this fault.

  15. Australian coal year book 1986

    1986-01-01

    This yearbook presents a review of the Australian coal industry during the 1984-85 financial year. Included are details on mines, future prospects, coal export facilities and ports, annual cost statistics and a index of coal mine owners.

  16. SamplingStrata: An R Package for the Optimization of Strati?ed Sampling

    Giulio Barcaroli

    2014-11-01

    Full Text Available When designing a sampling survey, usually constraints are set on the desired precision levels regarding one or more target estimates (the Ys. If a sampling frame is available, containing auxiliary information related to each unit (the Xs, it is possible to adopt a stratified sample design. For any given strati?cation of the frame, in the multivariate case it is possible to solve the problem of the best allocation of units in strata, by minimizing a cost function sub ject to precision constraints (or, conversely, by maximizing the precision of the estimates under a given budget. The problem is to determine the best stratification in the frame, i.e., the one that ensures the overall minimal cost of the sample necessary to satisfy precision constraints. The Xs can be categorical or continuous; continuous ones can be transformed into categorical ones. The most detailed strati?cation is given by the Cartesian product of the Xs (the atomic strata. A way to determine the best stratification is to explore exhaustively the set of all possible partitions derivable by the set of atomic strata, evaluating each one by calculating the corresponding cost in terms of the sample required to satisfy precision constraints. This is una?ordable in practical situations, where the dimension of the space of the partitions can be very high. Another possible way is to explore the space of partitions with an algorithm that is particularly suitable in such situations: the genetic algorithm. The R package SamplingStrata, based on the use of a genetic algorithm, allows to determine the best strati?cation for a population frame, i.e., the one that ensures the minimum sample cost necessary to satisfy precision constraints, in a multivariate and multi-domain case.

  17. Preliminary numerical simulation for shallow strata stability of coral reef in South China Sea

    Tang, Qinqin; Zhan, Wenhuan; Zhang, Jinchang

    2017-04-01

    Coral reefs are the geologic material and special rock and soil, which live in shallow water of the tropic ocean and are formed through biological and geological action. Since infrastructure construction is being increasingly developed on coral reefs during recent years, it is necessary to evaluate the shallow strata stability of coral reefs in the South China Sea. The paper is to study the borehole profiles for shallow strata of coral reefs in the South China Sea, especially in the hydrodynamic marine environment?, and to establish a geological model for numerical simulation with Geo-Studio software. Five drilling holes show a six-layer shallow structure of South China Sea, including filling layer, mid-coarse sand, coral sand gravel, fine sand, limestone debris and reef limestone. The shallow coral reef profile next to lagoon is similar to "layers cake", in which the right side close to the sea is analogous to "block cake". The simulation results show that coral reef stability depends on wave loads and earthquake strength, as well as the physical properties of coral reefs themselves. The safety factor of the outer reef is greater than 10.0 in the static condition, indicating that outer reefs are less affected by the wave and earthquake. However, the safety factor next to lagoon is ranging from 0.1 to 4.9. The main reason for the variations that the strata of coral reefs close to the sea are thick. For example, the thickness of reef limestone is more than 10 m and equivalent to the block. When the thickness of inside strata is less than 10 m, they show weak engineering geological characteristics. These findings can provide useful information for coral reef constructions in future. This work was funded by National Basic Research Program of China (contract: 2013CB956104) and National Natural Science Foundation of China (contract: 41376063).

  18. Sedimentary basin analysis and petroleum potential of the Cretaceous and Tertiary strata in Korea.

    Son, Jin-Dam; Kwak, Young-Hoon; Bong, Pil-Yoon [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    Since 1992 sedimentary basin analysis to assess petroleum potential of the Cretaceous and Tertiary strata in the Korean onshore and continental shelf have been carried out. The Cretaceous non-marine strata mainly occupy the Gyeongsang Basin in southeastern part of the Korean Peninsula and small basins such as Haenam and Gyeokpo depressions in western coastal areas. The Tertiary strata are mostly distributed in Domi, Cheju, Socotra subbasins, and Okinawa Trough in the South Continental Shelf, and Kunsan and Heuksan basins in the West. The basin evolution and petroleum potential for each basins are characterized as follow. The Cretaceous Gyeongsang sediments were deposited in three subbasins including Milyang, Euisung and Yongyang subbasins. The black shales in Nakdong and Jinju formations are interpreted to contain abundant organic matter during the deposition, thermal maturity reaching up to the zone of dry gas formation. Because porosity and permeability are too low, the sandstones can act as a tight gas reservoir rather than conventional oil and gas reservoir. The latest Cretaceous strata of Haenam and Kyeokpo depressions in western coastal area are correlated into the Yuchon Volcanic Group of the Gyeongsang Basin. Petroleum potential of the Early Cretaceous basin in the West Continental Shelf could be relatively high in terms of sedimentary basin filled with thick lacustrine sediments. The Kunsan basin in the West Continental Shelf originated in the Early Cretaceous time expanded during the Paleocene time followed by regional erosion at the end of Paleocene on which Neogene sediment have been accumulated. The Paleocene-Eocene sublacustrine shales may play an major role as a source and cap rocks. South Continental Shelf Basin is subdivided by Cheju subbasin in the center, Socotra Subbasin to the west, Domi Subbasin to the northeast and Okinawa Trough to the East. The potential hydrocarbon traps associated with anticline, titled fault blocks, fault, unconformity

  19. Seventh symposium on coal mine drainage research. NCA/BCR coal conference and Expo IV

    None

    1977-01-01

    The Seventh Symposium on Coal Mine Drainage Research, sponsored by the National Coal Association and Bituminous Coal Research, Inc., was held at the Kentucky Fair and Exposition Center, Louisville, Kentucky, October 18-20, 1977. Seventeen papers from the proceedings have been entered individually into EDB and ERA. Topics covered include chemical reactions of pyrite oxidation and acid formation in spoil banks, abandoned mines, etc., formation of small acid lakes from the drainage and their neutralization by natural and other neutralization measures, trace elements in acid mine drainage, ground water contamination, limnology, effects of surface mined ground reclamation and neutralization, water purification and treatment, mining and coal preparation plant waste disposal, ash and fly ash disposal (to minimize leaching from the wastes), runoff from large coal storage stockpiles during storms (prevention of environmental effects by collection and neutralization by passing through an ash pond). (LTN)

  20. Influence of overpressure on formation velocity evaluation of Neogene strata from the eastern Bengal Basin, Bangladesh

    Zahid, Khandaker M.; Uddin, Ashraf

    2005-06-01

    Interpretation of sonic log data of anticlinal structures from eastern Bangladesh reveals significant variations of acoustic velocity of subsurface strata. The amount of variation in velocity is 32% from Miocene to Pliocene stratigraphic units in Titas and Bakhrabad structure, whereas 21% in Rashidpur structure. Velocity fluctuations are influenced by the presence of gas-bearing horizons, with velocities of gas-producing strata 3-7% lower than laterally equivalent strata at similar depth. Average velocities of Miocene Boka Bil and Bhuban formations are, respectively, 2630 and 3480 m/s at Titas structure; 2820 and 3750 m/s at Bakhrabad; and 3430 and 3843 m/s at the Rashidpur structure. From the overall velocity-depth distribution for a common depth range of 915-3000 m, the Titas, Bakhrabad and Rashidpur structures show a gradual increase in velocity with depth. In contrast, the Sitakund anticline in SE Bangladesh reveals a decrease in velocity with depth from 3000 to 4000 m, probably due to the presence of overpressured mudrocks of the Bhuban Formation. Tectonic compression, associated with the Indo-Burmese plate convergence likely contributed the most toward formation of subsurface overpressure in the Sitakund structure situated in the Chittagong-Tripura Fold Belt of the eastern Bengal basin, Bangladesh.

  1. Tectonic subsidence analyses of miogeoclinal strata from mesozoic marginal basin of Peru

    Devlin, W.J.

    1988-01-01

    The Western Peruvian trough is composed of an eastern miogeoclinical facies of carbonate and clastic strata, and a western eugeoclinal facies consisting of a succession of volcanic and sedimentary rocks. In norther and central Peru, the miogeocline is located between a tectonic hinge adjacent to platformal facies of the Maranon geanticline on the east, and an outer marginal high bounded by the Cordillera Blanca fault and Tapacocha axis on the west. Miogeoclinal and platformal strata in southern Peru occur in a broad belt between Arequipa and Lago Titicaca. A marginal basin setting has been proposed for the Western Peruvian trough and the several kilometers of subsidence in the basin has been attributed to back-arc extension and crustal thinning. As a test of this model, quantitative tectonic subsidence curves were constructed from representative sections within miogeoclinar strata from four localities. Preliminary results indicate that the calculated curves have the same overall form as the age-depth curve for ocean floor, suggesting that subsidence was controlled by cooling and thermal contraction of heated lithosphere. The slopes of the curves are less than those for subsidence of oceanic lithosphere. However, they are in agreement with geologic evidence that the miogeocline accumulated on continental crust. Significant variations in the timing of onset, duration, and magnitude of subsidence are observed between sections from northern and southern Peru.

  2. Numerical Modeling of Mechanical Behavior for Buried Steel Pipelines Crossing Subsidence Strata.

    J Zhang

    Full Text Available This paper addresses the mechanical behavior of buried steel pipeline crossing subsidence strata. The investigation is based on numerical simulation of the nonlinear response of the pipeline-soil system through finite element method, considering large strain and displacement, inelastic material behavior of buried pipeline and the surrounding soil, as well as contact and friction on the pipeline-soil interface. Effects of key parameters on the mechanical behavior of buried pipeline were investigated, such as strata subsidence, diameter-thickness ratio, buried depth, internal pressure, friction coefficient and soil properties. The results show that the maximum strain appears on the outer transition subsidence section of the pipeline, and its cross section is concave shaped. With the increasing of strata subsidence and diameter-thickness ratio, the out of roundness, longitudinal strain and equivalent plastic strain increase gradually. With the buried depth increasing, the deflection, out of roundness and strain of the pipeline decrease. Internal pressure and friction coefficient have little effect on the deflection of buried pipeline. Out of roundness is reduced and the strain is increased gradually with the increasing of internal pressure. The physical properties of soil have a great influence on the mechanical properties of buried pipeline. The results from the present study can be used for the development of optimization design and preventive maintenance for buried steel pipelines.

  3. Australian black coal statistics 1991

    1992-01-01

    This third edition of Australian black coal statistics covers anthracite, bituminous and subbituminous coals. It includes maps and figures on resources and coal fields and statistics (mainly based on the calendar year 1991) on coal demand and supply, production, employment and productivity in Australian coal mines, exports, prices and ports, and domestic consumption. A listing of coal producers by state is included. A final section presents key statistics on international world trade in 1991. 54 tabs.

  4. Prospects for coal: technical developments

    Kaye, W G; Peirce, T J

    1983-07-01

    This article summarises the reasons for predicting an increase in the use of coal as an industrial energy source in the United Kingdom. The development of efficient and reliable coal-burning techniques is therefore of great importance. Various techniques are then discussed, including conventional combustion systems, fluidised bed combustion systems, fluidised bed boilers and furnaces, coal and ash handling, coal-liquid mixtures, coal gasification and coal liquefaction. (4 refs.)

  5. Coal combustion technology in China

    Huang, Z.X.

    1994-01-01

    Coal is the most important energy source in China, the environmental pollution problem derived from coal burning is rather serious in China. The present author discusses coal burning technologies both in boilers and industrial furnaces and their relations with environmental protection problems in China. The technological situations of Circulating Fluidized Bed Coal Combustor, Pulverized Coal Combustor with Aerodynamic Flame Holder and Coal Water Slurry Combustion have been discussed here as some of the interesting problems in China only. (author). 3 refs

  6. Discrete Fracture Network Models for Risk Assessment of Carbon Sequestration in Coal

    Jack Pashin; Guohai Jin; Chunmiao Zheng; Song Chen; Marcella McIntyre

    2008-07-01

    A software package called DFNModeler has been developed to assess the potential risks associated with carbon sequestration in coal. Natural fractures provide the principal conduits for fluid flow in coal-bearing strata, and these fractures present the most tangible risks for the leakage of injected carbon dioxide. The objectives of this study were to develop discrete fracture network (DFN) modeling tools for risk assessment and to use these tools to assess risks in the Black Warrior Basin of Alabama, where coal-bearing strata have high potential for carbon sequestration and enhanced coalbed methane recovery. DFNModeler provides a user-friendly interface for the construction, visualization, and analysis of DFN models. DFNModeler employs an OpenGL graphics engine that enables real-time manipulation of DFN models. Analytical capabilities in DFNModeler include display of structural and hydrologic parameters, compartmentalization analysis, and fluid pathways analysis. DFN models can be exported to third-party software packages for flow modeling. DFN models were constructed to simulate fracturing in coal-bearing strata of the upper Pottsville Formation in the Black Warrior Basin. Outcrops and wireline cores were used to characterize fracture systems, which include joint systems, cleat systems, and fault-related shear fractures. DFN models were constructed to simulate jointing, cleating, faulting, and hydraulic fracturing. Analysis of DFN models indicates that strata-bound jointing compartmentalizes the Pottsville hydrologic system and helps protect shallow aquifers from injection operations at reservoir depth. Analysis of fault zones, however, suggests that faulting can facilitate cross-formational flow. For this reason, faults should be avoided when siting injection wells. DFN-based flow models constructed in TOUGH2 indicate that fracture aperture and connectivity are critical variables affecting the leakage of injected CO{sub 2} from coal. Highly transmissive joints

  7. Exploratory Research on Novel Coal

    Winschel, R.A.; Brandes, S.D.

    1998-05-01

    The report presents the findings of work performed under DOE Contract No. DE-AC22 -95PC95050, Task 3 - Flow Sheet Development. A novel direct coal liquefaction technology was investigated in a program being conducted by CONSOL Inc. with the University of Kentucky Center for Applied Energy Research and LDP Associates. The process concept explored consists of a first-stage coal dissolution step in which the coal is solubilized by hydride ion donation. In the second stage, the products are catalytically upgraded to refinery feedstocks. Integrated first-stage and solids-separation steps were used to prepare feedstocks for second-stage catalytic upgrading. An engineering and economic evaluation was conducted concurrently with experimental work throughout the program. Parameters were established for a low-cost, low-severity first-stage reaction system. A hydride ion reagent system was used to effect high coal conversions of Black Thunder Mine Wyoming subbituminous coal. An integrated first-stage and filtration step was successfully demonstrated and used to produce product filtrates with extremely low solids contents. High filtration rates previously measured off-line in Task 2 studies were obtained in the integrated system. Resid conversions of first-stage products in the second stage were found to be consistently greater than for conventional two-stage liquefaction resids. In Task 5, elementally balanced material balance data were derived from experimental results and an integrated liquefaction system balance was completed. The economic analysis indicates that the production of refined product (gasoline) via this novel direct liquefaction technology is higher than the cost associated with conventional two-stage liquefaction technologies. However, several approaches to reduce costs for the conceptual commercial plant were recommended. These approaches will be investigated in the next task (Task 4) of the program.

  8. Thermal coal utilization for the ESCAP region

    1982-01-01

    A selection of papers is presented originating from talks to coal utilization workshops for the ASEAN region in 1981. The papers cover: planning aspects - economic and technical aspects of coal usage, long term planning for fuel coal needs, planning and coal selection for coal-fired power plants, coal availability and marketing, and economic aspects of coal usage in developing countries; combustion and plant - changing from coal to oil, principles and problems of coal combustion, use of indigenous and imported coals and their effects on plant design, coal pulverizing mills, ash and dust disposal, environmental aspects of coal combustion, industrial sized coal-fired boilers; transport and storage -ocean shipment, coal receival facilities and associated operations, shipping and rail transport, coal handling and transport, environmental issue in the transport and handling of coal, coal preparation and blending; testing and properties - coal types, characterization properties and classification; training power plant operators; the cement industry and coal, the Australian black coal industry.

  9. Reconnaissance coal study in the Susitna basin, 2014

    David L. LePain,; Stanley, Richard G.; Harun, Nina T.; Helmold, Kenneth T.; Tsigonis, Rebekah

    2015-01-01

    The Alaska Division of Geological & Geophysical Surveys (DGGS) conducted fieldwork during the summer of 2014 in the Susitna basin as part of an ongoing evaluation of the hydrocarbon potential of frontier basins, particularly those near the Railbelt region (for example, Decker and others, 2013; Gillis and others, 2013). Topical studies associated with this recent work include sedimentary facies analysis (LePain and others, 2015) and structural geology investigations (Gillis and others, 2015). The Susitna basin contains coal-bearing Paleogene and Neogene strata correlative with formations that host oil and gas in Cook Inlet basin to its south. Isotopic signatures of natural gas reservoired in the Miocene/Pliocene Sterling and Miocene Beluga Formations suggest a biogenic origin for Cook Inlet gas (Claypool and others, 1980). To assess the biogenic gas potential of the Susitna basin, it is important to obtain information from its coal-bearing units.Characteristics of coal, such as maturity/rank and cleat development are key parameters influencing viability of a biogenic gas system (Laubach and others, 1998). In an early study of the Susitna basin (Beluga–Yentna region), Barnes (1966) identified, analyzed, and recognized potentially valuable subbituminous coal resources at Fairview Mountain, Canyon Creek, and Johnson Creek. Merritt (1990), in a sedimentological study to evaluate surface coal mining potential of the Tertiary rocks of the Susitna basin (Susitna lowland), concluded that the basin contained several billion tons of mineable reserves. This preliminary report offers a brief summary of new information on coals in the Susitna Basin acquired during associated stratigraphic studies (see LePain and others, 2015). 

  10. The Indonesian coal industry

    Cook, A.; Daulay, B.

    2000-01-01

    In this comprehensive article the authors describe the origins and progress of the Indonesian coal industry and the role it plays, and will play, in the domestic energy scene and world coal trade. In the '80s, the Indonesian coal industry laid the basis for major expansion such that coal production rose from under a million tonnes in 1983 to 10.6 million tonnes in 1990, 50.9 million tonnes by 1996 and 61.2 million tonnes in 1992. At the same time, exports have increased from 0.4 million tonnes to 44.8 million tonnes. Current export levels are higher than originally expected, due in part to a slow down in the construction of electric power stations and a partial switch to natural gas. This has slowed the rate at which domestic coal demand has built up. The majority of coals currently exported are low rank steam coals, but some of the higher rank and very low ash coals are used for blast furnace injection, and a very small proportion may even be used within coking blends, even though they have poor coking properties. The Indonesian coal industry has developed very rapidly over the last six years to become a significant exporter, especially within the ASEAN context. The resources base appears to be large enough to support further increases in production above those already planned. It is probable that resources and reserves can be increased above the current levels. It is likely that some reserves of high value coals can be found, but it is also probable that the majority of additions to reserves will be lower in rank (and therefore quality) compared with the average of coals currently being mined. Reserves of qualities suitable for export will support that industry for a considerable period of time. However, in the longer term, the emphasis of production will increasingly swing to the domestic market

  11. Investigation of the age and geological thermal history of the strata containing dinosaurs fossil in Tianzhen county of Shanxi Province

    Kang Tiesheng; Wang Lanfen; Wang Shicheng; Cheng Zhengwu

    1996-01-01

    The age and thermal history of the strata containing dinosaurs fossil in Tianzhen County of Shanxi Province have been studied using apatite and zircon fission track analysis. It is shown that the burial age of dinosaurs skeletons is not earlier than Late Cretaceous. The provenance area of the strata had experienced heating events with temperature higher than 200-250 degree C 73 Ma ago. But the strata has been at environmental temperature and never been affected by heating events since the dinosaurs skeletons were buried

  12. Investigation of the age and geological thermal history of the strata containing dinosaurs fossil in Tianzhen county of Shanxi Province

    Tiesheng, Kang; Lanfen, Wang; Shicheng, Wang [Academia Sinica, Beijing, BJ (China). Inst. of High Energy Physics; Qiqing, Pang [Hebei College of Geology, Shijiazhuang (China); Zhengwu, Cheng [Institute of Geology, MGMR, Beijing (China)

    1996-10-01

    The age and thermal history of the strata containing dinosaurs fossil in Tianzhen County of Shanxi Province have been studied using apatite and zircon fission track analysis. It is shown that the burial age of dinosaurs skeletons is not earlier than Late Cretaceous. The provenance area of the strata had experienced heating events with temperature higher than 200-250 degree C 73 Ma ago. But the strata has been at environmental temperature and never been affected by heating events since the dinosaurs skeletons were buried.

  13. Analysis of radioactivity in coal, cinders, fly ash and discharges from the stack

    Meide, A.

    1985-01-01

    Gamma measurements of coal samples originating from several supplying countries proved that the South African coal has about double U-238 and Ra-226 concentration and about treble Th-232 concentration compared to coal from the other countries. Gamma measurements of coal, cinders and fly ash samples from five coal-fueled plants indicate somewhat higher concentrations of Th-232 in cinders and U-238 and Th-232 in fly ashes than those described in literature. The ratio Po-210/Pb-210 was about 2 for fly ash particulates <35μ. A positive correlation between ash percentage and radioactivity of coal might be assumed. (EG)

  14. Dissolution of subbituminous coal in tetrahydroquinoline

    Silver, H F; Frazee, W S; Broderick, T E; Hurtubise, R J

    1986-05-01

    Two different samples of Wyodak subbituminous coal from the Powder River Basin in Wyoming were liquefied in a two dm/sup 3/ batch reactor using 1,2,3,4 tetrahydroquinoline, THQ, as a solvent. Sufficient sample was produced to determine product boiling ranges by distillation and to measure THQ distribution in the product. Product distillation showed that even at cyclohexane conversions greater than 50%, net distillate yields produced using THQ as a solvent were negative. In some cases, high boiling, coal-derived residue yields were greater than the dry coal charged to the reactor. These observations have been attributed to THQ losses resulting from dimerization of the THQ and reactions between THQ and coal derived components. 5 references.

  15. Elk Valley Coal innovation paving the way

    Chen, C.; Ednie, H.; Weldon, H.

    2006-09-15

    Elk Valley Coal maintains performance optimization across its six metallurgical coal operations. Performance, personnel issues, and training are discussed. Programmes at Fording River, Greenhills, and Coal Mountain are described. Fording River is implementing new computer systems and high-speed wireless networks. The pit control system and the equipment maintenance and remote maintenance programmes are being improved. The Glider Kit program to rebuild major equipment is described. Safety and productivity measures at Greenhills include testing and evaluation of innovations such as the Drilling and Blasting System (DABS), a payload monitor on a shovel, and two GPS-based systems. Blasting methods, a timing study that examines wall stability, fragmentation simulation, and the Six Mine structure at Coal Mountain are described. 5 photos.

  16. Dry piston coal feeder

    Hathaway, Thomas J.; Bell, Jr., Harold S.

    1979-01-01

    This invention provides a solids feeder for feeding dry coal to a pressurized gasifier at elevated temperatures substantially without losing gas from the gasifier by providing a lock having a double-acting piston that feeds the coals into the gasifier, traps the gas from escaping, and expels the trapped gas back into the gasifier.

  17. Development of coal resources

    NONE

    1995-09-01

    It is an important issue to expand stable coal supply areas for Japan, especially to assure stable supply of overseas coals. The investigations on geological structures in foreign countries perform surveys on geological structures in overseas coal producing countries and basic feasibility studies. The investigations select areas with greater business risks in coal producing countries and among private business entities. The geological structure investigations were carried out on China, Indonesia and Malaysia and the basic feasibility studies on Indonesia during fiscal 1994. The basic coal resource development investigations refer to the results of previous physical explorations and drilling tests to develop practical exploration technologies for coal resources in foreign countries. The development feasibility studies on overseas coals conduct technological consultation, surface surveys, physical explorations, and trial drilling operations, and provide fund assistance to activities related thereto. Fiscal 1994 has provided fund assistance to two projects in Indonesia and America. Fund loans are provided on investigations for development and import of overseas coals and other related activities. Liability guarantee for development fund is also described.

  18. Coal in Canada

    Salaff, S.

    1991-01-01

    This article examines the potential market for coal-fired independent power projects in western Canada. The topics of the article include emissions issues, export potential for power produced, and financial and other assistance to independent power producers offered by British Columbia Hydro and coal mining companies in the region, including financing of projects and power distribution services including connecting to the USA grids

  19. Black coal. [Australia

    Pratt, R

    1973-01-01

    Statistics are given for the Australian black coal industry for 1970-3 (production, value, employment, wages and salaries, productivity, trade, stocks, consumption, export contracts, exploration, etc.). In less detail, world coal trade is reviewed and coke production is mentioned briefly. (LTN )

  20. Effect of microwave irradiation on petrophysical characterization of coals

    Hong, Yi-du; Lin, Bai-quan; Zhu, Chuan-jie; Li, He

    2016-01-01

    Highlights: • Microwave energy increase porosity, pore size and numbers of coals. • Growth rates of porosity decreased at first then increased with microwave energy. • NMR can be reliable to measure coal samples. • Microwave energy may have the potential for degassing of coal seams. - Abstract: The experimental work described in this paper aims to study the effect of microwave irradiation on petrophysical characterization of coals. Twenty coal samples were irradiated at 2.45 GHz with variable power (2, 4, 6 kW). The temperature, mass and specific heat capacity of coal samples were measured and calculated. The effect of microwave irradiation on the porosity of coal samples was evaluated by the gravimetric method and nuclear magnetic resonance (NMR) measurements. The porosity obviously increases after microwave heating. Interestingly, growth rate of the porosity decreases at first then increases with microwave energy. The turning point is approximately 100 kJ. The influence of microwave irradiation on pore size, throat size and pore numbers of coal samples were also evaluated by NMR measurements. It suggest that the pore size, throat size and pore numbers are obviously increase with microwave energy. In a word, it appears likely that microwave energy may have the potential for the degassing coal seams.

  1. Enzymatic desulfurization of coal

    Boyer, Y.N.; Crooker, S.C.; Kitchell, J.P.; Nochur, S.V.

    1991-05-16

    The overall objective of this program was to investigate the feasibility of an enzymatic desulfurization process specifically intended for organic sulfur removal from coal. Toward that end, a series of specific objectives were defined: (1) establish the feasibility of (bio)oxidative pretreatment followed by biochemical sulfate cleavage for representative sulfur-containing model compounds and coals using commercially-available enzymes; (2) investigate the potential for the isolation and selective use of enzyme preparations from coal-utilizing microbial systems for desulfurization of sulfur-containing model compounds and coals; and (3) develop a conceptual design and economic analysis of a process for enzymatic removal of organic sulfur from coal. Within the scope of this program, it was proposed to carry out a portion of each of these efforts concurrently. (VC)

  2. The renaissance of coal

    Schernikau, Lars

    2013-01-01

    There is hardly another energy resource where public opinion and reality lie as far apart as they do for coal. Many think of coal as an inefficient relic from the era of industrialisation. However, such views underestimate the significance of this energy resource both nationally and globally. In terms of global primary energy consumption coal ranks second behind crude oil, which plays a central role in the energy sector. Since global electricity use is due to rise further, coal, being the only energy resource that can meet a growing electricity demand over decades, stands at the beginning of a renaissance, and does so also in the minds of the political leadership. Coal is indispensable as a bridging technology until the electricity demand of the world population can be met primarily through renewable resources.

  3. Methane of the coal

    Vasquez, H.

    1997-01-01

    In the transformation process of the vegetable material to the coal (Carbonization), the products that are generated include CH 4, CO2, N2 and H2. The methane is generated by two mechanisms: below 50 centigrade degree, as product of microbial decomposition, the methanogenic is generated; and above 50 centigrade degree, due to the effects of the buried and increase of the range of the coal, the thermogenic methane is detachment, as a result of the catagenic. The generated methane is stored in the internal surfaces of the coal, macro and micro pores and in the natural fractures. The presence of accumulations of gas of the coal has been known in the entire world by many years, but only as something undesirable for its danger in the mining exploitation of the coal

  4. China's coal industry

    Karmazin, V A

    1988-09-01

    Presents data on China's coal industry. China's coal reserves are estimated to be 4,000 million Mt; annual production is over 800 Mt. Eleven new mining projects have been recently completed. They were financed with participation of foreign capital (US$ 1,400 million). Twenty-five new mines with 32.27 Mt production capacity were planned to be put into operation in 1988. Annual coal production is expected to increase to 870 Mt in 1990 at a cost of US$ 8,500 million. Numerical data on China's individual coal basins, new schemes, capital outlay and foreign capital participation are given. The dynamic development of China's coal industry since 1949 is briefly reviewed and management methods are explained.

  5. Industrial coal utilization

    None

    1979-01-01

    The effects of the National Energy Act on the use of coal in US industrial and utility power plants are considered. Innovative methods of using coal in an environmentally acceptable way are discussed: furnace types, fluidized-bed combustion, coal-oil-mixtures, coal firing in kilns and combustion of synthetic gas and liquid fuels. Fuel use in various industries is discussed with trends brought about by uncertain availability and price of natural gas and fuel oils: steel, chemical, cement, pulp and paper, glass and bricks. The symposium on Industrial Coal Utilization was sponsored by the US DOE, Pittsburgh Energy Technology Center, April 3 to 4, 1979. Twenty-one papers have been entered individually into the EDB. (LTN)

  6. USA coal producer perspective

    Porco, J. [Alpha Natural Resources, Latrobe, PA (US). Alpha Energy Global Marketing

    2004-07-01

    The focus is on the Central Appalachian coal industry. Alpha Natural Resources was formed in 2002 from Pittston Coal's Virginia and Coastal operations. AMCI's U.S. operations and Mears Enterprises in Pennsylvania were acquired later. The company produces 20-21 million tonnes per year and sells 20 million tonnes of steam coal and 10 million tonnes of exports, including some coal that is brokered. Foundry coke is a major product. Capital investment has resulted in increased productivity. Central Appalachia is expected to continue as a significant coal-producing region for supplying metallurgical coke. Production is expected to stabilize, but not increase; so the mines will have a longer life. 31 slides/overheads are included.

  7. Underground Coal Thermal Treatment

    Smith, P. [Univ. of Utah, Salt Lake City, UT (United States); Deo, M. [Univ. of Utah, Salt Lake City, UT (United States); Eddings, E. [Univ. of Utah, Salt Lake City, UT (United States); Sarofim, A. [Univ. of Utah, Salt Lake City, UT (United States); Gueishen, K. [Univ. of Utah, Salt Lake City, UT (United States); Hradisky, M. [Univ. of Utah, Salt Lake City, UT (United States); Kelly, K. [Univ. of Utah, Salt Lake City, UT (United States); Mandalaparty, P. [Univ. of Utah, Salt Lake City, UT (United States); Zhang, H. [Univ. of Utah, Salt Lake City, UT (United States)

    2012-01-11

    The long-term objective of this work is to develop a transformational energy production technology by insitu thermal treatment of a coal seam for the production of substitute natural gas (SNG) while leaving much of the coal's carbon in the ground. This process converts coal to a high-efficiency, low-GHG emitting gas fuel. It holds the potential of providing environmentally acceptable access to previously unusable coal resources. This topical report discusses the development of experimental capabilities, the collection of available data, and the development of simulation tools to obtain process thermo-chemical and geo-thermal parameters in preparation for the eventual demonstration in a coal seam. It also includes experimental and modeling studies of CO2 sequestration.

  8. Coal and petroleum resources in the Appalachian basin: index maps of included studies: Chapter B.1 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

    Ruppert, Leslie F.; Trippi, Michael H.; Kinney, Scott A.; Ruppert, Leslie F.; Ryder, Robert T.

    2014-01-01

    This chapter B.1 of U.S. Geological Survey (USGS) Professional Paper 1708 provides index maps for many of the studies described in other chapters of the report. Scientists of the USGS and State geological surveys studied coal and petroleum resources in the central and southern Appalachian structural basins. In the southern Appalachian basin, studies focused on the coal-bearing parts of the Black Warrior basin in Alabama. The scientists used new and existing geologic data sets to create a common spatial geologic framework for the fossil-fuel-bearing strata of the central Appalachian basin and the Black Warrior basin in Alabama.

  9. State coal profiles, January 1994

    1994-02-02

    The purpose of State Coal Profiles is to provide basic information about the deposits, production, and use of coal in each of the 27 States with coal production in 1992. Although considerable information on coal has been published on a national level, there is a lack of a uniform overview for the individual States. This report is intended to help fill that gap and also to serve as a framework for more detailed studies. While focusing on coal output, State Coal Profiles shows that the coal-producing States are major users of coal, together accounting for about three-fourths of total US coal consumption in 1992. Each coal-producing State is profiled with a description of its coal deposits and a discussion of the development of its coal industry. Estimates of coal reserves in 1992 are categorized by mining method and sulfur content. Trends, patterns, and other information concerning production, number of mines, miners, productivity, mine price of coal, disposition, and consumption of coal are detailed in statistical tables for selected years from 1980 through 1992. In addition, coal`s contribution to the State`s estimated total energy consumption is given for 1991, the latest year for which data are available. A US summary of all data is provided for comparing individual States with the Nation as a whole. Sources of information are given at the end of the tables.

  10. Sedimentology of the lower Karoo Supergroup fluvial strata in the Tuli Basin, South Africa

    Bordy, Emese M.; Catuneanu, Octavian

    2002-11-01

    The Karoo Supergroup in the Tuli Basin (South Africa) consists of a sedimentary sequence (˜450-500 m) composed of four stratigraphic units, namely the informal Basal, Middle and Upper Units, and the formal Clarens Formation. The units were deposited in continental settings from approximately Late Carboniferous to Middle Jurassic. This paper focuses on the ˜60-m-thick Basal Unit, which was examined in terms of sedimentary facies and palaeo-environments based on evidence provided by primary sedimentary structures, palaeo-flow measurements, palaeontological findings, borehole data (59 core descriptions) and stratigraphic relations. Three main facies associations have been identified: (i) gravelstone (breccias and conglomerate-breccias), (ii) sandstone and (iii) fine-grained sedimentary rocks. The coarser facies are interpreted as colluvial fan deposits, possibly associated with glaciogenic diamictites. The sandstone facies association is mainly attributed to channel fills of low sinuosity, braided fluvial systems. The coal-bearing finer-grained facies are interpreted as overbank and thaw-lake deposits, and represent the lower energy correlatives of the sandy channel fills. Sediment aggradation in this fluvio-lacustrine system took place under cold climatic conditions, with floating lake ice likely associated with lacustrine environments. Palaeo-current indicators suggest that the highly weathered, quartz-vein-rich metamorphic rock source of the Basal Unit was situated east-northeast of the study area. The accumulation of the Basal Unit took place within the back-bulge depozone of the Karoo foreland system. In addition to flexural subsidence, the amount of accommodation in this tectonic setting was also possibly modified by extensional tectonism in the later stages of the basin development. Based on sedimentological and biostratigraphic evidence, the coal-bearing fine-grained facies association displays strong similarities with the Vryheid Formation of the main Karoo

  11. Natural radionuclides in coal and waste material originating from coal fired power plant

    Marovic, Gordana; Franic, Zdenko; Sencar, Jasminka; Petrinec, Branko; Bituh, Tomislav; Kovac, Jadranka

    2008-01-01

    This paper presents long-term investigations of natural radioactivity in coal, used for power production in the coal-fired power plant (CFPP) situated on the Adriatic coast, and resulting slag and ash. Activity concentrations of 40 K, 232 Th, 226 Ra and 238 U in used coal and resulting waste material have been measured for 25 years. As expected, it was demonstrated that the content of radionuclides in deposited bottom and filter ash material are closely related with radionuclide activity concentrations and mineral matter fraction in used coals. The external hazard index has been calculated and discussed for the slag and ash depository. During the first decade of operation of the CFPP has been used domestic coal produced in nearby area characterized by higher background radiation compared with the rest of Croatia. Therefore, the coal itself had relatively high 226 Ra and 238 U activity concentrations while potassium and thorium content was very low, 40 K activity concentrations being 2-9% and those of 232 Th 1-3% of total activity. As, in addition, the sulphur concentrations in coal were very high use of domestic coal was gradually abandoned till it was completely substituted by imported coal originated from various sources and of low natural radioactivity. Upon this, activity concentrations of uranium series radionuclides in deposited waste materials decreased significantly. Consequently, waste material i.e., slag and ash, generated in the last several years of coal fired power plant operation could be readily used in cement industry and as additive to other building materials, without any special restrictions according to the Croatian regulations dealing with building materials and European directives. (author)

  12. P-ANFO: new era in surface coal mining; P-ANFO: acik ocak komur isletmeciliginde yeni bir cag

    Tek, A. [Atlas Ltd., Istanbul (Turkey)

    1999-07-01

    ANFO, an effective and inexpensive explosive, is widely used in rock blasting operations. However, for weak strata, ANFO often produces too much shock energy and leads to inefficiencies in the mining operation. Especially in Turkish surface coal mines where ANFO is used with the decking system, it is desirable to develop a low shock energy but a high heave energy ammonium nitrate based explosive. 3 refs., 9 figs., 1 tab.

  13. Research on preventive technologies for bed-separation water hazard in China coal mines

    Gui, Herong; Tong, Shijie; Qiu, Weizhong; Lin, Manli

    2018-03-01

    Bed-separation water is one of the major water hazards in coal mines. Targeted researches on the preventive technologies are of paramount importance to safe mining. This article studied the restrictive effect of geological and mining factors, such as lithological properties of roof strata, coal seam inclination, water source to bed separations, roof management method, dimensions of mining working face, and mining progress, on the formation of bed-separation water hazard. The key techniques to prevent bed-separation water-related accidents include interception, diversion, destructing the buffer layer, grouting and backfilling, etc. The operation and efficiency of each technique are corroborated in field engineering cases. The results of this study will offer reference to countries with similar mining conditions in the researches on bed-separation water burst and hazard control in coal mines.

  14. Determining origin of underground water in coal mines by means of natural isotopes and other geochemical parameters

    Dolenec, T; Pezdic, J; Herlec, U; Kuscer, D; Mitrevski, G [Institut Josef Stefan, Ljubljana (Yugoslavia)

    1989-07-01

    Presents a preliminary report on origin of water in Slovenian brown coal mines. Water, coal and strata samples from the Hrastnik and Ojstro mines were analyzed for changes in chemical composition. Water samples were also analyzed for changes in isotopic composition and inorganic carbon and sulfur contents. Chemical, isotopic and geochemical techniques are described and results are presented with 21 diagrams. An attempt is made to explain the origin and age of water flowing from mine aquifers into mine rooms, and to explain the interdependence of surface and underground water flow. 10 refs.

  15. Interaction and the structures of coal

    Opaprakasit, Pakorn

    solvents, which in turn enhances the coal extraction yield. Finally, the evidence for the presence of a glass transition temperature in coal was examined. The results from Differential Scanning Calorimetry showed that no transition similar to the Tg can be observed in bulk coal or its low-molecular weight fraction, pyridine soluble extracted material, at a temperature near 110°C. In contrast, an irreversible transition that is due to water evaporation has been found. Thermomechanical measurements, which are very sensitive to the presence of a Tg in synthetic polymers, also provided no evidence for a Tg below temperatures where chemical reactions occur. Additionally, the results from Thermomechanical Analysis showed an expansion in size when the coal was heated to 300°C, which is associated with a "caking" process. The degree of expansion during this "caking" process is about five times greater in the direction perpendicular to the bedding plane than the parallel, indicating an accommodation of anisotropic strain relaxation, which was generated in the direction perpendicular to the bedding plane during the coalification process.

  16. Early Devonian polygnathids of Northeast Asia and correlation of Pragian/Emsian strata of the marginal seas of Angarida

    Baranov, V.; Slavík, Ladislav; Blodgett, R. B.

    2014-01-01

    Roč. 89, č. 3 (2014), s. 645-678 ISSN 1214-1119 Institutional support: RVO:67985831 Keywords : Early Devonian * Pragian/Emsian strata * Angarida Subject RIV: DB - Geology ; Mineralogy Impact factor: 1.515, year: 2014

  17. Modelling and analysis of global coal markets

    Trueby, Johannes

    2013-01-01

    The thesis comprises four interrelated essays featuring modelling and analysis of coal markets. Each of the four essays has a dedicated chapter in this thesis. Chapters 2 to 4 have, from a topical perspective, a backward-looking focus and deal with explaining recent market outcomes in the international coal trade. The findings of those essays may serve as guidance for assessing current coal market outcomes as well as expected market outcomes in the near to medium-term future. Chapter 5 has a forward-looking focus and builds a bridge between explaining recent market outcomes and projecting long-term market equilibria. Chapter 2, Strategic Behaviour in International Metallurgical Coal Markets, deals with market conduct of large exporters in the market of coals used in steel-making in the period 2008 to 2010. In this essay I analyse whether prices and trade-flows in the international market for metallurgical coals were subject to non-competitive conduct in the period 2008 to 2010. To do so, I develop mathematical programming models - a Stackelberg model, two varieties of a Cournot model, and a perfect competition model - for computing spatial equilibria in international resource markets. Results are analysed with various statistical measures to assess the prediction accuracy of the models. The results show that real market equilibria cannot be reproduced with a competitive model. However, real market outcomes can be accurately simulated with the non-competitive models, suggesting that market equilibria in the international metallurgical coal trade were subject to the strategic behaviour of coal exporters. Chapter 3 and chapter 4 deal with market power issues in the steam coal trade in the period 2006 to 2008. Steam coals are typically used to produce steam either for electricity generation or for heating purposes. In Chapter 3 we analyse market behaviour of key exporting countries in the steam coal trade. This chapter features the essay Market Structure Scenarios in

  18. Modelling and analysis of global coal markets

    Trueby, Johannes

    2013-01-17

    The thesis comprises four interrelated essays featuring modelling and analysis of coal markets. Each of the four essays has a dedicated chapter in this thesis. Chapters 2 to 4 have, from a topical perspective, a backward-looking focus and deal with explaining recent market outcomes in the international coal trade. The findings of those essays may serve as guidance for assessing current coal market outcomes as well as expected market outcomes in the near to medium-term future. Chapter 5 has a forward-looking focus and builds a bridge between explaining recent market outcomes and projecting long-term market equilibria. Chapter 2, Strategic Behaviour in International Metallurgical Coal Markets, deals with market conduct of large exporters in the market of coals used in steel-making in the period 2008 to 2010. In this essay I analyse whether prices and trade-flows in the international market for metallurgical coals were subject to non-competitive conduct in the period 2008 to 2010. To do so, I develop mathematical programming models - a Stackelberg model, two varieties of a Cournot model, and a perfect competition model - for computing spatial equilibria in international resource markets. Results are analysed with various statistical measures to assess the prediction accuracy of the models. The results show that real market equilibria cannot be reproduced with a competitive model. However, real market outcomes can be accurately simulated with the non-competitive models, suggesting that market equilibria in the international metallurgical coal trade were subject to the strategic behaviour of coal exporters. Chapter 3 and chapter 4 deal with market power issues in the steam coal trade in the period 2006 to 2008. Steam coals are typically used to produce steam either for electricity generation or for heating purposes. In Chapter 3 we analyse market behaviour of key exporting countries in the steam coal trade. This chapter features the essay Market Structure Scenarios in

  19. Interpreting Fracture Patterns in Sandstones Interbedded with Ductile Strata at the Salt Valley Anticline, Arches National Park, Utah

    Lorenz, John C.; Cooper, Scott P.

    2001-01-01

    Sandstones that overlie or that are interbedded with evaporitic or other ductile strata commonly contain numerous localized domains of fractures, each covering an area of a few square miles. Fractures within the Entrada Sandstone at the Salt Valley Anticline are associated with salt mobility within the underlying Paradox Formation. The fracture relationships observed at Salt Valley (along with examples from Paleozoic strata at the southern edge of the Holbrook basin in northeastern Arizona, a...

  20. Predicting the combustion kinetics of Chinese coals

    Niksa, Stephen [Niksa Energy Associates LLC, Belmont, CA (United States); Fujiwara, Naoki [Idemitsu Kosan Co., Ltd, Chiba (Japan). Coal and Environment Research Lab.

    2013-07-01

    The database on the devolatilization of Chinese coals in the English literature represents coals from all ranks and the major Chinese mines. It was mostly acquired with TGAs. There are sufficient datasets from devices that imposed rapid heating rates to bracket combustor behavior. The domains of heating rate, temperature, pressure, and particle size are either directly relevant to combustion conditions, or close enough to manage with modest extrapolations. Whereas the data on ultimate total yields is sufficient to validate a model for any coal type, more detailed product distributions and char compositions would be desirable. Based on the accurate interpretation of this database, there are few unresolved issues surrounding the applicability of FLASHCHAIN {sup registered} for combustion applications in China. The sub-database on devolatilization under rapid heating conditions represents 34 samples. The predicted yields were within the measurement uncertainties of 4 daf wt. % for 29 of these coals. Among the five ultimate yields that were not accurately predicted, three had measured values less than the proximate volatile matter (PVM), despite the rapid heating rates in the tests. Similarly, the sub-database on devolatilization under slow heating conditions characterizes ultimate devolatilization yields of 30 samples. The predicted yields were within the measurement uncertainties for 22 of these coals. Among the eight that were not accurately predicted, three had measured values that were much lower than the PVM (which is a problem even after accounting for the slow heating rates in the tests) and three were in studies that did not report ultimate analyses for the coals tested. Unfortunately, the database on the combustion behavior of the chars from Chinese coals is insufficient to specify char oxidation kinetics.

  1. NMR imaging studies of coal

    Ma, Z.R.; Zhang, P.Z.; Ding, G.L.; Li, L.Y.; Ye, C.H. [University of Science and Technology, Beijing (China). Dept. of Chemistry

    1996-06-01

    The permeation transportation and swelling behavior of solvents into coal are investigated by NMR imaging using pyridine-d{sub 5} and acetone-d{sub 6}. Images of coal swollen with deuterated solvents illuminate proton distributions of mobile phases within the coal macromolecular networks. More information about the chemical and physical structure of coal can be obtained using NMR imaging techniques.

  2. Structural implications of underground coal mining in the Mesaverde Group in the Somerset Coal Field, Delta and Gunnison Counties, Colorado

    Christopher J. Carroll; Eric Robeck; Greg Hunt; Wendell Koontz [Colorado Geological Survey, Denver, CO (United States)

    2004-07-01

    Paleogene and Neogene faults and fractures on the eastern edge of the Colorado Plateau are present in Mesaverde Group coal and sandstone beds. Recent observations of coal cleat orientation in relation to faults in coal mines have significant impacts for mine planning in the area. Faults, coal cleats, and natural fractures are interpreted to show a structural evolution of the Mesaverde Group through time. This field trip included a visit to two active underground coal mines, the Bowie Resources' Bowie No. 2 Mine, and Mountain Coal's West Elk Mine. Mine geologists discussed structural styles including fault orientations and timing, cleat development, and rotation. Geologic encounters ranging from fault flooding, subsidence, mine fires, methane gas problems, and land use restrictions were also discussed. Coal cleat development and open-mode fractures in adjacent sandstones were observed on outcrops and compared to underground measurements in coal mines in the Somerset Coal Field, Colorado's most productive. Coal cleat orientations along a reverse fault in one mine showed rotation in relation to possible Neogene age displacement.

  3. Clean coal technology: The new coal era

    1994-01-01

    The Clean Coal Technology Program is a government and industry cofunded effort to demonstrate a new generation of innovative coal processes in a series of full-scale showcase`` facilities built across the country. Begun in 1986 and expanded in 1987, the program is expected to finance more than $6.8 billion of projects. Nearly two-thirds of the funding will come from the private sector, well above the 50 percent industry co-funding expected when the program began. The original recommendation for a multi-billion dollar clean coal demonstration program came from the US and Canadian Special Envoys on Acid Rain. In January 1986, Special Envoys Lewis and Davis presented their recommendations. Included was the call for a 5-year, $5-billion program in the US to demonstrate, at commercial scale, innovative clean coal technologies that were beginning to emerge from research programs both in the US and elsewhere in the world. As the Envoys said: if the menu of control options was expanded, and if the new options were significantly cheaper, yet highly efficient, it would be easier to formulate an acid rain control plan that would have broader public appeal.

  4. Coal: Less than lackluster

    Doerell, P.

    1994-01-01

    Not many in the world coal industry will remember 1993 as a good year. The reasons for the poor state of affairs were first the weak economic climate, and second, the energy glut. For the first time after expanding steadily since the 70s, seaborne trade in hard coal fell by about 4% to 350M mt. Steam coal accounted for a good half of this volume. While demand continued to rise in the newly industrialized countries of the Pacific area, imports into Europe of both coking coal and steam coal fell sharply. The United States, CIS, and Canada had to accept substantial losses of export volume. Australia, as well as South Africa, Colombia, and Indonesia consolidated their market positions and Poland, too, recorded high volumes available for export. The positive news came from Australia, where in mid-December the New South Wales coal industry reported an increase in the net profit after tax from $A83M (about $55M) to $A98M (about $126M) in 1992/1993. This success was however ascribed less to an improvement in the fundamental mining indicators than to the fall in the Australian dollar and the lowering of corporate tax. The reduction in capital investment by 26% down to $A330M (after the previous year when it had also been cut by 25%) is seen by the chairman of the NSW Coal Assoc. as not auguring well for the industry's ability to meet the forecast growth in demand to the year 2000

  5. Coal in competition

    Manners, G

    1985-06-01

    During the past decade world coal consumption has expanded by about 26% whilst energy demands overall have grown by only 17%. This is because of the increased price of oil products, plus a period during which the costs of mining coal in many parts of the world have been moderately well contained. Over-ambitious forecasts of coal demand have encouraged the considerable over-investment in coalmining capacity that exists today. Costs of winning coal and transporting it are low, but sales depend on the rate of growth of a country's demand for energy. Some countries are more successful at marketing coal than others. Amongst the major factors that influence the rate of substitution of one source of energy for another is the nature and age of the boiler stock. The outcome of the developing environmental debate and calls for reduction in SO/sub 2/ and NO/sub x/ emissions from coal-fired boilers is going to affect coal's fortunes in the 1990's.

  6. A coal combine

    Wlachovsky, I; Bartos, J

    1980-02-15

    A design is presented for a coal combine, equipped with two drum operational units, on whose both ends of the upper surface of the body, two coal saws are mounted with the help of a lever system. These saws, found in an operational position, form a gap in the block of the coal block, which is not embraced by the drum operational unit. The coal block, found between the gap and the support, falls down onto the longwall scraper conveyor. The lever system of each coal saw is controlled by two hydraulic jacks. One of the jacks is mounted vertically on the facial wall of the body of the combine and is used for the hoisting for the required height of the horizontal arm of the lever, reinforced by one end in the hinge on the body of the combine. On the ''free'' end of that lever, a coal saw is mounted in a hinge-like fashion and which is connected by the hydraulic jack to the horizontal arm of the lever system. This hydraulic jack is used for the clamping of the coal saw to the face.

  7. Radiant-and-plasma technology for coal processing

    Vladimir Messerle

    2012-12-01

    Full Text Available Radiant-and-plasma technology for coal processing is presented in the article. Thermodynamic computation and experiments on plasma processing of bituminous coal preliminary electron-beam activated were fulfilled in comparison with plasma processing of the coal. Positive influence of the preliminary electron-beam activation of coal on synthesis gas yield was found. Experiments were carried out in the plasma gasifier of 100 kW power. As a result of the measurements of material and heat balance of the process gave the following integral indicators: weight-average temperature of 2200-2300 K, and carbon gasification degree of 82,4-83,2%. Synthesis gas yield at thermochemical preparation of raw coal dust for burning was 24,5% and in the case of electron-beam activation of coal synthesis gas yield reached 36,4%, which is 48% higher.

  8. Reduced emissions from inexpensive high-sulphur coal briquettes

    Gammage, R.B.; Wachter, E.A.; Wade, J.; Wilson, D.L.; Haas, J.W.; Ahmad, N.; Siltain, F.; Raza, M.Z.

    1992-01-01

    Airborne emissions were measured during the combustion of Pakistani high-sulphur coal, cold briquetted with lime and clay; comparison was made to emissions from raw coal and traditional fuels burnt in a native, mud-lined Angethi stove. Compared to raw coal, the amended coal gave fourfold reduced emission of respirable-size particles (RSP) and threefold reduced total releases of SO 2 . In domestic cooking, substitution of the amended coal briquettes for traditional fuels will not worsen indoor air quality with respect to CO, SO 2 , NO x , and RSP. The high peak amounts of CO (100--250 ppm), SO 2 (2--5 ppm), and NO x (1--5 ppm) were limited to the early phase of burning. The high thermal value of the coal briquettes together with a simple briquetting technology, make this fuel an attractive energy alternative in countries that are underdeveloped, developing, or experiencing major restructuring

  9. Feasibility of high-helium natural gas exploration in the Presinian strata, Sichuan Basin

    Jian Zhang

    2015-01-01

    Full Text Available Helium in China highly depends on import at present, so the most practical way to change the situation is searching for medium-to-large natural gas fields with high helium content. Therefore, the hydrocarbon accumulation mechanism and the helium origin of the Weiyuan high-helium natural gas reservoir have been analyzed to find out the feasibility of finding natural gas field with high helium content in the Presinian strata of the Sichuan Basin. Based on twelve outcrop sections and drilling data of four wells encountering the Presinian strata, the petrological features, sedimentary facies and source rocks of Presinian strata were systematically analyzed, which shows that the sedimentary formation developed in the Presinian is the Nanhua system, and the stratigraphic sequence revealed by outcrop section in the eastern margin includes the Nantuo, Datangpo, Gucheng and Liantuo Fms, and it is inferred that the same stratigraphic sequence may occur inside the basin. The Nantuo, Gucheng and Liantuo Fms are mainly glacial deposits of glutenite interbedded with mudstone; the Datangpo Fm is interglacial deposits of sandstone and shale, the lower part shale, rich in organic matter, is fairly good source rock. Further study showed that the Nantuo coarse-grained clastic reservoir, Datangpo source rock and the intruded granite “helium source rock” make up a good high-helium gas system. Controlled by the early rift, the thick Presinian sedimentary rocks occur primarily inside the rift. The distribution of sedimentary rocks and granite in the basin was predicted by use of the seismic data, which shows that the feasibility of finding high-helium gas reservoirs in Ziyang area of the Sichuan Basin is great.

  10. Combustion characteristics of intensively cleaned coal fractions. Effect of mineral matter

    Rubiera, F.; Arenillas, A.; Fuente, E.; Pis, J.J. [Inst. Nacional de Carbon, Oviedo (Spain); Ivatt, S. [ETSU, Harwell, Didcot (United Kingdom)

    1997-12-31

    The purpose of this work has been to assess the effect that intensive coal cleaning exerts on the combustion behaviour of different density-separated coal fractions. Samples with ash contents varying from 39% for the raw coal, to 2% for the cleanest fraction were obtained after density separation. Temperature-programmed combustion and isothermal gasification in air were used to measure the reactivities of the parent coal and the cleaned fractions. Coal and char reactivities increased with increasing ash content of the samples. Thermal analysis-mass spectrometry of the low-temperature ashes was also carried out in order to study the reactions of coal minerals under combustion conditions. (orig.)

  11. Algebraic varieties in the Birkhoff strata of the Grassmannian Gr(2): Harrison cohomology and integrable systems

    Konopelchenko, B G; Ortenzi, G

    2011-01-01

    The local properties of the families of algebraic subsets W g in the Birkhoff strata Σ 2g of Gr (2) containing the hyperelliptic curves of genus g are studied. It is shown that the tangent spaces T g for W g are isomorphic to the linear spaces of 2-coboundaries. Particular subsets in W g are described by the integrable dispersionless coupled KdV systems of hydrodynamical type defining a special class of 2-cocycles and 2-coboundaries in T g . It is demonstrated that the blows-ups of such 2-cocycles and 2-coboundaries and gradient catastrophes for associated integrable systems are interrelated. (paper)

  12. Environment of deposition and stratigraphy of the uranium-bearing strata around Beaufort West, South Africa

    Horowitz, A.

    1976-04-01

    Palynological analyses of some 50 samples collected from uranium-bearing strata - as well as the layers immediately above and below them - around Beaufort West, South Africa, indicate that these sediments were laid down in a wide, rather shallow delta in Late Permian times. Most of the sediments are fluvio-deltaic, and most of the plant remains were transported from the north, the hinterland in those times. A considerable percentage of the microfossils, e.g. Veryhachium and hystrichospheres, are clearly from a marine environment. The occurrence of marine microfossils in the spectrum, as compared with those of terrestrial provenance, increases considerably southwards [af

  13. Boiler briquette coal versus raw coal: Part I--Stack gas emissions.

    Ge, S; Bai, Z; Liu, W; Zhu, T; Wang, T; Qing, S; Zhang, J

    2001-04-01

    Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM10 and PM2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM10, 0.38 for PM2.5, 20.7 for SO2, and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM10, 0.30 for PM2.5, 7.5 for SO2, and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM10, 0.87 for PM2.5, 46.7 for SO2, and 15 for CO, while those of the BB-coal were 2.51 for PM10, 0.79 for PM2.5, 19.9 for SO2, and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/steam conversion factors, were 0.23 for PM10, 0.12 for PM2.5, 6.4 for SO2, and 2.0 for CO, while those of the BB-coal were 0.30 for PM10, 0.094 for PM2.5, 2.4 for SO2, and 1.7 for CO. PM10 and PM2.5 elemental compositions are also presented for both types of coal tested in the study.

  14. Boiler Briquette Coal versus Raw Coal: Part I-Stack Gas Emissions.

    Ge, Su; Bai, Zhipeng; Liu, Weili; Zhu, Tan; Wang, Tongjian; Qing, Sheng; Zhang, Junfeng

    2001-04-01

    Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM 10 and PM 2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM 10 , 0.38 for PM 25 , 20.7 for SO 2 , and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM 10 , 0.30 for PM 2 5 , 7.5 for SO 2 , and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM 10 , 0.87 for PM 25 , 46.7 for SO 2 , and 15 for CO, while those of the BB-coal were 2.51 for PM 10 , 0.79 for PM 2.5 , 19.9 for SO 2 , and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/ steam conversion factors, were 0.23 for PM 10 , 0.12 for PM 2.5 , 6.4 for SO 2 , and 2.0 for CO, while those of the BB-coal were 0.30 for PM 10 , 0.094 for PM 2.5 , 2.4 for SO 2 , and 1.7 for CO. PM 10 and PM 2.5 elemental compositions are also presented for both types of coal tested in the study.

  15. Nuclear assay of coal. Volume 6. Mass flow devices for coal handling

    Anon.

    1979-01-01

    The mass of coal entering the boiler per unit time is an essential parameter for determinig the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

  16. Nuclear assay of coal. Volume 6. Mass flow devices for coal handling. Final report

    Gozani, T.; Elias, E.; Bevan, R.

    1980-04-01

    The mass of coal entering the boiler per unit time is an essential parameter for determining the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

  17. Microbial desulfurization of coal

    Bos, P.; Boogerd, F.C.; Kuenen, J.G.

    1992-01-01

    In recent years, studies have been initiated to explore the possibilities of the use of biological systems in coal technology. This chapter discusses the principles behind the bioprocessing of coal, the advantages and disadvantages, and the economic feasibility of the process. For large-scale, coal-using, energy-producing plants, stack gas cleaning should be the treatment of choice. Biodesulfurization is preferable with industrial, small-scale, energy-producing plants. Treatment of the stack gases of these plants is not advisable because of high investment costs. Finally, it should be realized that biodesulfurization produces a waste stream that needs further treatment. 91 refs

  18. Coal-fired generation

    Breeze, Paul

    2015-01-01

    Coal-Fired Generation is a concise, up-to-date and readable guide providing an introduction to this traditional power generation technology. It includes detailed descriptions of coal fired generation systems, demystifies the coal fired technology functions in practice as well as exploring the economic and environmental risk factors. Engineers, managers, policymakers and those involved in planning and delivering energy resources will find this reference a valuable guide, to help establish a reliable power supply address social and economic objectives. Focuses on the evolution of the traditio

  19. Economic outlook for coal

    Denis Casey.

    1997-01-01

    Coal still a fundamental component of two major industries in New South Wales- electricity production and steel making. Its future will be shaped by its ability to meet expected international increases in demand for thermal coal, and by profitability and possible impact of greenhouse strategy decisions. By 2002 the demand for the State's coal is estimated at a total of 116 million tons and it expected to play an increased role in the fuel mix for electricity generation because of its competitive price, established technologies and abundant supply

  20. Coal potential of Antartica

    Rose, G.; McElroy, C.T.

    1987-01-01

    This report attempts to bring together available information on the coal deposits of Antarctica and discuss factors that would be involved if these deposits were to be explored and mined. Most of the reported principal coal deposits in Antarctica lie generally within the Transantarctic Mountains: the majority are of Permian age and are present in the Victoria Group of the Beacon Supergroup. Several other deposits have been recorded in East Antarctica and in the Antarctic Peninsula, including minor occurrences of Mesozoic and Tertiary coal and carbonaceous shale.

  1. Coal liquefaction becomes viable

    NONE

    2005-11-15

    In 2003 the May/June issue of CoalTrans International speculated that coal liquefaction would become viable due to falling coal prices. This has not proved the case but the sustained high oil price is sparking new interest. A survey by Energy Intelligence and Marketing Research during November 2005 revealed a growth in the number of projects under development or at the feasibility stage. The article reports projects in China, the USA, Australia, New Zealand, the Philippines and India. China is commissioning the first wave of large liquefaction plants. The key question is whether other countries, particularly the USA, will follow.

  2. Measurement of gamma-dose caused by built in coal slags with elevated 226Ra concentration, and the modelling of shielding

    Nemeth, Cs.; Somlai, J.; Nenyei, A.; Skrinyar, M.; Kanyar, B.; Nemeth, P.; Hoffer, K.

    2000-01-01

    Slags, derived from coal mined in the neighbourhood of the town Tatabanya in Hungary, have been used as filling and insulating material for buildings of houses, block of flats, schools and kindergartens. The slag samples come from here have elevated concentrations of 226 Ra (range of 850 - 2400 Bq x kg -1 ). Therefore, the external gamma dose rates at 1 m height were about four times higher than the world average. It has been found, based on the modelling, that the dose rate could be decreased with 70 - 80% using an appropriate thickness of concrete or barite-concrete layers. (author)

  3. Revival of coal. [France and USA

    1981-05-01

    This edition is devoted to the production and consumption of coal in France. It presents a study of the main topics involved, discusses the position of coal in France - under what form should it beused, and deals with coal consumption in cement works role of coal for urban district heating, future of coal gasification in France, France's coal policy, coal industry in the USA, underground gasification of coal, France's coal reserves, etc.. (In French)

  4. Investigation of the feasibility of underground coal gasification in North Dakota, United States

    Pei, Peng; Nasah, Junior; Solc, Jaroslav; Korom, Scott F.; Laudal, Daniel; Barse, Kirtipal

    2016-01-01

    Highlights: • A four-year feasibility study of underground coal gasification is presented. • A test site was selected for feasibility investigation. • Gasification test, a hydrogeological study and geomechanical study were performed. • Results suggest favorable conditions for UCG development at the selected site. - Abstract: Underground coal gasification (UCG) is a promising technology that has the potential to recover currently-unmineable coal resources. The technical feasibility and economic success of a UCG project is highly site specific. Any risks associated with UCG, such as subsidence, groundwater contamination, and syngas quality, should be sufficiently evaluated through a feasibility study. This paper presents a four-year UCG feasibility study utilizing lignite seams in North Dakota, United States. Four wells were drilled through the lignite seams at a selected site, and lignite and strata cores were recovered. A geological model of the formation was built, coal and rock properties were analyzed, and field hydrogeological tests and laboratory gasification tests were performed. This work provided valuable insights in rock mechanics, hydrogeology, and coal properties. The study results show that the selected site is suitable for development of a UCG plant because there are minimal induced subsidence risks, there is hydrological isolation from major aquifers and the coal produces desirable syngas quality for liquid fuel production. Methodologies developed in this study will benefit the design, optimization and management of the UCG process.

  5. Influence of a Large Pillar on the Optimum Roadway Position in an Extremely Close Coal Seam

    Li Yang

    2016-01-01

    Full Text Available Based on the mining practice in an extremely close coal seam, theoretical analysis was conducted on the vertical stress distribution of the floor strata under a large coal pillar. The vertical stress distribution regulation of a No. 5 coal seam was revealed. To obtain the optimum position of the roadway that bears the supporting pressure of a large coal pillar, numerical modeling was applied to analyze the relation among the stress distribution of the roadway surrounding the rock that bears the supporting pressure of a large coal pillar, the plastic zone distribution of the roadway surrounding the rock, the surrounding rock deformation, and the roadway layout position. The theoretical calculation results of the stress value, stress variation rate, and influencing range of the stress influencing angle showed that the reasonable malposition of the No. 5 coal seam roadway was an inner malposition of 4 m. The mining practice showed the following: the layout of No. 25301 panel belt roadway at the position of the inner malposition of 4 m was reasonable, the roadway support performance was favourable without deformation, and ground pressure was not obvious. The research achievement of this study is the provision of a reference for roadway layouts under similar conditions.

  6. 基于压水试验的深部煤层底板岩层阻渗性能研究∗%Study on permeability barrier performance of deep coal seam floor based on packer permeability test

    孙晓倩; 张冬; 张新武; 王言剑

    2014-01-01

    In situ field packer permeability test,being a reliable method to obtain the param-eters of permeability barrier performance of strata,was used to explore this performance of deep coal seam floor. A large amount of measured data were obtained after the test on two layers of floor strata. The test results showed that these two layers of floor strata could not seep in initial state due to stronger barrier performance until the fracture and connection led to seepage. Co MPared with the first and repeated packer permeability tests on these two layers of floor strata, the variation of water pressure in measured pore was associated with that in water injection hole, but the seepage pressure in the first time was higher than that in second time,showing that the permeability barrier performance of strata turned weaker after first packer permeability test and was easy to form seepage. Using permeability coefficient and permeability barrier strength as in-dexes,the permeability barrier performance of floor strata has been quantitatively evaluated,and the results showed that the tested strata was characterized with high barrier performance and weak permeability.%原位现场压水试验是获取岩层阻渗性能参数的可靠方法,为探究某煤矿深部煤层底板阻渗能力,采用现场压水试验方法对底板两段岩层进行了测试并获取了大量的实测数据。结果分析表明:该底板两测试段岩层在原始状态均不导渗,阻渗性较强,直至压裂导通才形成导渗条件;对两段岩层均进行了初次和重复两个压水过程,对比两次试验可知,测渗孔水压力与注水孔水压力的关联变化趋势大致相同,但初次压水的起始导渗水压明显高于重复压水,表明在初次压水后岩层的阻渗能力降低,更易形成导渗;采用渗透系数和阻渗强度作为指标,对底板岩层的阻渗性能进行了量化评价,结果表明测试岩层表现出明显的高阻弱渗的特点。

  7. Prevention and forecasting of rock burst hazards in coal mines

    Lin-ming Dou; Cai-ping Lu; Zong-long Mu; Ming-shi Gao [China University of Mining & Technology, Xuzhou (China). State Key Laboratory for Coal Resource and Mine Safety

    2009-09-15

    Rock bursts signify extreme behavior in coal mine strata and severely threaten the safety of the lives of miners, as well as the effectiveness and productivity of miners. In our study, an elastic-plastic-brittle model for the deformation and failure of coal/rock was established through theoretical analyses, laboratory experiments and field testing, simulation and other means, which perfectly predict sudden and delayed rock bursts. Based on electromagnetic emission (EME), acoustic emission (AE) and microseismic (MS) effects in the process from deformation until impact rupture of coal-rock combination samples, a multi-parameter identification of premonitory technology was formed, largely depending on these three forms of emission. Thus a system of classification for forecasting rock bursts in space and time was established. We have presented the intensity weakening theory for rock bursts and a strong-soft-strong (3S) structural model for controlling the impact on rock surrounding roadways, with the objective of laying a theoretical foundation and establishing references for parameters for the weakening control of rock bursts. For the purpose of prevention, key technical parameters of directional hydraulic fracturing are revealed. Based on these results, as well as those from deep-hole controlled blasting in coal seams and rock, integrated control techniques were established and anti-impact hydraulic props, suitable for roadways subject to hazards from rockbursts have also been developed. These technologies have been widely used in most coal mines in China, subject to these hazards and have achieved remarkable economic and social benefits. 28 refs., 9 figs., 1 tab.

  8. Clean coal initiatives in Indiana

    Bowen, B.H.; Irwin, M.W.; Sparrow, F.T.; Mastalerz, Maria; Yu, Z.; Kramer, R.A.

    2007-01-01

    Purpose - Indiana is listed among the top ten coal states in the USA and annually mines about 35 million short tons (million tons) of coal from the vast reserves of the US Midwest Illinois Coal Basin. The implementation and commercialization of clean coal technologies is important to the economy of the state and has a significant role in the state's energy plan for increasing the use of the state's natural resources. Coal is a substantial Indiana energy resource and also has stable and relatively low costs, compared with the increasing costs of other major fuels. This indigenous energy source enables the promotion of energy independence. The purpose of this paper is to outline the significance of clean coal projects for achieving this objective. Design/methodology/approach - The paper outlines the clean coal initiatives being taken in Indiana and the research carried out at the Indiana Center for Coal Technology Research. Findings - Clean coal power generation and coal for transportation fuels (coal-to-liquids - CTL) are two major topics being investigated in Indiana. Coking coal, data compilation of the bituminous coal qualities within the Indiana coal beds, reducing dependence on coal imports, and provision of an emissions free environment are important topics to state legislators. Originality/value - Lessons learnt from these projects will be of value to other states and countries.

  9. Clean utilization of coal

    Yueruem, Y.

    1992-01-01

    This volume contains 23 lectures presented at the Advanced Study Institute on 'Chemistry and Chemical Engineering of Catalytic Solid Fuel Conversion for the Production of Clean Synthetic Fuels', which was held at Akcay, Edremit, Turkey, between 21 July and August 3, 1991. Three main subjects: structure and reactivity of coal; cleaning of coal and its products, and factors affecting the environmental balance of energy usage and solutions for the future, were discussed in the Institute and these are presented under six groups in the book: Part 1. Structure and reactivity of coal; Part 2. Factors affecting environmental balance; Part 3. Pre-usage cleaning operations and processes; Part 4. Upgrading of coal liquids and gases; Part 5. Oxygen enriched processes; and Part 6. Probable future solution for energy and pollution problems. Separate abstracts have been prepared for all the lectures

  10. Coal exports still growing

    Blain, M.

    1998-01-01

    It is shown that the swings and roundabouts of the Asian economic shake out and Australian dollar devaluation are starting to work their way through the Australian export coal market. Perhaps somewhat surprisingly, at this stage the results are not proving to be as bad as were at first predicted by some market watchers. Export revenue and tonnages are up 12% for the year to July 98. Coal exports totaling $9.5 billion left Australia's shores in the 12 months confirming coal as Australia's single largest export revenue earner. Sales volumes in the present financial year are still increasing, the market being driven by steadily increasing Asian demand for steaming coal from places like Korea, Malaysia, Thailand and the Philippines

  11. Coal Mine Permit Boundaries

    Earth Data Analysis Center, University of New Mexico — ESRI ArcView shapefile depicting New Mexico coal mines permitted under the Surface Mining Control and Reclamation Act of 1977 (SMCRA), by either the NM Mining these...

  12. Coal industry - memoranda

    1986-01-01

    This paper contains 41 memoranda submitted to the UK House of Commons Energy Committee containing views on the UK coal industry and responses to questions from the Select Committee. The following organizations are represented: Department of Energy; National Coal Board; APEX; BACM; NACODS; NUM; UDM; TUC; CEGB; Electricity Council; Northern Ireland Electricity Service; SSEB; British Gas Corporation; BP; Conoco (UK) Ltd.; Costain Mining Ltd.; Shell UK Ltd.; BSC; ICI; Boots; CBI; PSA; Solid Fuel Advisory Service; Domestic Coal Consumers Council; Associated Heat Services; Association of Shell Boilermakers; Babcock Power Ltd.; GEC; Foster Wheeler Power Products; ABMEC; British Longwall Mining Association; Federation of Civil Engineering Contractors; Federation of Small Mines of Great Britain; Chamber of Coal Traders; Coalfield Communities Campaign; Nottinghamshire County Council; Federation of Self-Employed and Small Businesses; the Colombian, Belgian and Netherlands Embassies; and Plaid Cymru.

  13. Coal terminal directory

    NONE

    2008-06-15

    The directory gives a comprehensive listing of the world's coal terminals, in a total of 50 countries including information on throughput, facilities, storage capacity, and vessel size limitation.

  14. Strategies regarding the environmental problems in Valea Jiului coal basin

    Babut, G.; Moraru, R.; Matei, I.

    1998-01-01

    The recent progress in environmental management concepts and tools allows to combine economic operation of industry with environmental protection if appropriate measures are used. The paper outlines some key issues facing the mining industry in the greatest romanian coal basin, where coal is industrially exploited for more than 100 years. 3 refs

  15. Coal flotation technical review

    Heiser, N. [C. Clarkson & Associates Pty. Ltd., Brisbane, Qld. (Australia)

    1996-10-01

    The Australian Coal Association Research Program (ACARP) recently commissioned a study into the status of flotation in coal preparation, in order to direct limited funds to areas of maximum benefit. The primary purpose of the study was the assessment of new flotation technologies, including those commercially available and those still under development. Technologies examined included: the Jameson Cell, Microcel, and Ekof cell. Problems and advantages are discussed, with suggestions for future areas of research. 3 figs.

  16. Prediction of CO2 leakage during sequestration into marine sedimentary strata

    Li, Qi; Wu Zhishen; Li Xiaochun

    2009-01-01

    Deep ocean storage of CO 2 could help reduce the atmospheric level of greenhouse gas as part of a climate change mitigation strategy. In this paper, a multiphase flow model of CO 2 sequestration into deep ocean sediments was designed associated with the formation of CO 2 hydrates. A simplified assumption was proposed to predict the critical time of CO 2 leakage from marine sedimentary strata into seawater. Moreover, some principal parameters, which include the permeability, anisotropy, total injection amount, and length of the injection part of wellbores, were investigated by numerical simulations. The numerical estimates are used to assess the feasibility and effectiveness of CO 2 storage in deep ocean sediments. Accurately predicting the actual fate of liquid CO 2 sequestered into the marine sedimentary strata at depths greater than 500 m is complicated by uncertainties associated with not only the chemical-physical behavior of CO 2 under such conditions but also the geo-environment of disposal sites. Modeling results have shown some implications that the effectiveness of CO 2 ocean sequestration depends mainly on the injection conditions (such as injection rate, total injection amount, and the depth of injection), the site geology (such as permeability and anisotropy of disposal formations), and the chemical-physical behavior of CO 2 in marine environment

  17. Tools in the orbit space approach to the study of invariant functions: rational parametrization of strata

    Sartori, G; Valente, G

    2003-01-01

    Functions which are equivariant or invariant under the transformations of a compact linear group G acting in a Euclidean space R n , can profitably be studied as functions defined in the orbit space of the group. The orbit space is the union of a finite set of strata, which are semialgebraic manifolds formed by the G-orbits with the same orbit-type. In this paper, we provide a simple recipe to obtain rational parametrizations of the strata. Our results can be easily exploited, in many physical contexts where the study of equivariant or invariant functions is important, for instance in the determination of patterns of spontaneous symmetry breaking, in the analysis of phase spaces and structural phase transitions (Landau theory), in equivariant bifurcation theory, in crystal field theory and in most areas where use is made of symmetry-adapted functions. A physically significant example of utilization of the recipe is given, related to spontaneous polarization in chiral biaxial liquid crystals, where the advantages with respect to previous heuristic approaches are shown

  18. Tools in the orbit space approach to the study of invariant functions: rational parametrization of strata

    Sartori, G; Valente, G [Dipartimento di Fisica, Universita di Padova and INFN, Sezione di Padova, I-35131 Padova (Italy)

    2003-02-21

    Functions which are equivariant or invariant under the transformations of a compact linear group G acting in a Euclidean space R{sup n}, can profitably be studied as functions defined in the orbit space of the group. The orbit space is the union of a finite set of strata, which are semialgebraic manifolds formed by the G-orbits with the same orbit-type. In this paper, we provide a simple recipe to obtain rational parametrizations of the strata. Our results can be easily exploited, in many physical contexts where the study of equivariant or invariant functions is important, for instance in the determination of patterns of spontaneous symmetry breaking, in the analysis of phase spaces and structural phase transitions (Landau theory), in equivariant bifurcation theory, in crystal field theory and in most areas where use is made of symmetry-adapted functions. A physically significant example of utilization of the recipe is given, related to spontaneous polarization in chiral biaxial liquid crystals, where the advantages with respect to previous heuristic approaches are shown.

  19. Reprocessing of gas-cooled reactor particulate graphite fuel in a multi-strata transmutation system

    Laidler, J.J.

    2001-01-01

    Spent nuclear fuel discharged for light water reactors (LWRs) contains significant quantities of plutonium and other transuranic elements. Recent practice in Europe and Japan has been to recover the plutonium from spent fuel and recycle it to LWRs in the form of mixed uranium-plutonium oxide (MOX) fuel. Irradiation of the recycle fuel results in the generation of further plutonium and an increase in the isotopic concentration of the higher isotopes of plutonium, those having much lover fission cross sections than 239 Pu. This restricts plutonium recycle to one or two cycles, after which use of the plutonium becomes economically unfavorable. Recycle of the highly-transmuted plutonium in fast spectrum reactors can be an efficient method of fissioning this plutonium as well as other minor transuranics such as neptunium, americium and perhaps even curium. Those minor transuranics that are not conveniently burned in a fast reactor can be sent to an accelerator driven subcritical transmutation device for ultimate destruction. The preceding describes what has become known as a 'dual strata' or 'multi-strata' system. It is driven by the incentives to realize the maximum amount of energy from nuclear fuel and to eliminate the discharge of radio-toxic transuranic elements to the environment. Its implementation will be dependent in the long run upon the economic viability of the system and on the value placed by society on the elimination of radio-toxic materials that can conceivably be used in the manufacture of weapons of mass destruction. (author)

  20. High temperature superconductor based on thin strata reactively sputtered on metal targets. Final report

    Francke, C.; Meyer, B.; Wunderlich, R.; Mueller, J.

    1996-01-01

    SNS - Josephson contacts stable for a long period and dc SQUIDS working at 77 K were produced from the high temperature superconductor YBa 2 Cu 3 O 7-δ , where silver was used as the normal conductor. On MgO stages etched with ion beams, a defined section of the YBCO stratum can be produced and therefore a desired spacing can be set beteen the two YBCO electrodes. Structuring of the silver layer increases the normal conductive resistance of the Josephson contacts of the SQUIDs and therefore also the flux/voltage modulation stroke by up to 2 orders of mangitude. The dc SQUIDS in the so-called Ketchen design with 700 x 700 μm 2 square washers alone have a field sensitivity around 25 nT/Φ 0 . A multi-strata technology was developed from YBCO/STO/YBCO layer packages, which makes it possible to produce superconducting coils with corssovers and through contacts, which show critical currents of over 10 mA at 77 K. Using this multi-strata technology, flux transformers on 10 x 10 mm 2 STO substrates and on 20 x 20 mm 2 STO substrates were produced. Coupled to dc SQUIDs inductively in 'flip-chip' technique, such flux transformers supply a field sensitivity which is several times better than that of a flex transformer with a 10 x 10 mm 2 substrate. Field sensitivities around 0.2 nT/Φ 0 can be achieved. (orig./MM) [de