Mining the 510 coal seam prone to rock bursts and below a coal support pillar in a seam above

Energy Technology Data Exchange (ETDEWEB)

Major, M; Gebala, W

1983-10-01

The 510 coal seam, situated at a depth of 760 m below a support pillar left in an overlying coal seam, was mined by a system of longwall faces from 1979 to 1982. The seam was prone to rock bursts. Energy of rock bursts which occurred in the mine ranged from 10/SUP/5 to 10/SUP/6 J. The coal seam, 10 m thick, was mined by slicing. Faces were 140 m long. Stress concentrations caused by the suppport pillar left in the overlying coal seam were calculated. Curves which describe stress fluctuations were plotted. Rock burst hazards were determined by drilling. Drilling intervals depended on hazard degree and position of the test site in relation to the support pillar in the overlying coal seam. The face was 3 m high. Supports used in 2 gate roads were reinforced by steel and timber supports. Strong timber boards were placed at canopies of powered supports used at the working face. The face was situated at an angle of 10 degrees to the pillar axis. In the zone of critical stresses water infusion and shock blasting were used for rock burst prevention. These methods, plus reinforcement of the supports in gate roads and at the working face, guaranteed safe mining and prevented rock bursts. (8 refs.)

Prevention and forecasting of coal, rock and gas bursts in mines of Donets Coal Basin in USSR

Energy Technology Data Exchange (ETDEWEB)

Swidzinski, A

1977-11-01

Coal and methane bursts as well as sandstone and methane bursts are typical for the Donets Coal Basin. The most effective way of forecasting coal and methane bursts is drilling holes (3.5 m long, 45 mm diameter) and measuring the initial speed of gas outflow (5 litres/min gas outflow is a critical value). Additional parameters in this method are: coal firmness and porosity as well as thickness of coal bed. Forecasting sandstone and gas bursts is based on taking rock samples while drilling. When a sample 1 meter long consists of 30 to 40 so called discs, the danger of outburst is substantial, with the decreasing number of discs the probability of bursts also decreases. The following methods of prevention are used in the Donets Coal Basin: preparatory extraction of a layer protecting another layer below or above, where there is a danger of gas burst. This method is effective in 50% of all cases. Other methods include: filling coal beds with water under high pressure (average norm 25 1 water per 1 m

Respirable dust measured downwind during rock dust application.

Science.gov (United States)

Harris, M L; Organiscak, J; Klima, S; Perera, I E

2017-05-01

The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using untreated rock dust and rock dust treated with an anticaking additive. Using personal dust monitors, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH's Bruceton Experimental Mine using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners' exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device.

Study on intelligent prediction of broken rock zone thickness of coal mine roadways

Energy Technology Data Exchange (ETDEWEB)

Xu, G.; Jing, H. [China University of Mining and Technology, Xuzhou (China). School of Architecture and Civil Engineering

2005-03-01

Considering the problem of obtaining the thickness of broken rock zone, a booming intelligent prediction method with ANFIS (adaptive neuro-fuzzy inference system) was introduced into the thickness prediction. A stand-alone program with functions of creating and applying prediction systems was designed on the platform of MATLAB6.5. Then the program was used to predict the broken rock zone thickness of dips in the 12th coal mine, Pingdingshan Group Company of Coal Industry. The results show that the predicted values correlate well with the in-situ measured ones. Thereby the validity of the program is validated and it can provide a new approach to obtaining the broken zone thickness. 10 refs., 4 figs., 1 tab.

Relationships between data from Rock-Eval pyrolysis and proximate, ultimate, petrographic, and physical analyses of 142 diverse U.S. coal samples

Science.gov (United States)

Bostick, N.H.; Daws, T.A.

1994-01-01

Basic research on coal and oil shale led to automated pyrolysis analysis of petroleum source rocks; most widely used is the Rock-Eval equipment. In order to interpret Rock-Eval analyses in relation to traditional coal data, we analyzed 142 commercial coals with diverse rank, age, maceral and sulfur contents, for most regions of the United States. We compared the Rock-Eval data with traditional industrial coal data, including volatile matter, calorific value, hydrogen and oxygen content, free swelling index, and vitrinite reflectance. We found: (1) there is a close relationship between Tmax and vitrinite reflectance in the ranges 420-590??C Tmax and 0.4-3%Romax of most coals. (2) A close relationship between Tmax and volatile matter (%VM) extends through the entire sample range, including low-rank samples with 35-70% VM, a range where %VM is not considered to be a useful rank parameter. (3) TOC of medium- and high-rank coals is seriously under-measured by Rock-Eval; TOC of low-rank coals (less than 0.8%Romax) is close to "dry basis" carbon from ultimate analysis. (4) The direct relationships between oxygen index (OI) and %O and between hydrogen index (HI) and %H are clear, though only broadly defined. However, there is virtually no band of concentrated data points on the HI versus OI pseudo-Van Krevelen diagram comparable to the "development line" on the H/C versus O/C diagram. (5) There are systematic relationships between Rock-Eval and industrial coal parameters such as calorific value and FSI, but much standardization would be needed before Rock-Eval could find a place in the coal industry. Tests with blends of coal and quartz sand and with various loads of coal alone showed that the amount of organic matter in the Rock-Eval load greatly influences results. Total load in the crucible, if largely inert, plays a small role, however. Increasing absolute or relative coal content causes under-evaluation of Rock-Eval TOC and over-rating of hydrogen. Blends of several

Geochemistry of coal-measure source rocks and natural gases in deep formations in Songliao Basin, NE China

Energy Technology Data Exchange (ETDEWEB)

Mi, Jingkui; Zhang, Shuichang; Hu, Guoyi; He, Kun [State Key Laboratory for Enhanced Oil Recovery, Beijing (China); Petroleum Geology Research and Laboratory Center, Research Institute of Petroleum Exploration and Development, PetroChina (China); Key Laboratory for Petroleum Geochemistry, China National Petroleum Corp. (China)

2010-12-01

The natural gases developed in deep volcanic rock reservoirs of the Songliao Basin, NE China are characterized by enriched {delta}{sup 13}C value for methane and frequently reversal carbon isotopic distribution pattern. Although many researchers consider such gas type as an abiogenic origin, we believe the natural gases have a biogenic origin mainly except little inorganic gases and the reversal carbon isotopic distribution pattern of gases is caused by mixing of different origin gases. Methane carbon isotopic values for majority samples fall in the range from - 24 permille to - 32 permille, which is heavier than typical coal-type gases in other Chinese basins. There are several reasons caused heavy carbon isotope of methane: (1) Carbon isotopic values of source kerogen are 3-5 permille heavier than these from other basins; (2) Source rocks are at extremely high maturity stage with vitrinite reflectance mostly above 3.0%; (3) Portion of gas is derived from basement mudrock or slate with higher maturity. The observation on the organic from deep formation reveals that there is a relatively high content for liptinite, which reaches approximately 8 to 10%. The macerals component of source rock shows that the source rocks have some ability to generate oil. Small portion of oil was generated from high hydrogen content macerals in coals and shales as proof by oil found in microcrack and in micropore of coal and oil-bearing fluid inclusions grown in volcanic reservoir. The occurrence of pyrobitumen in volcanic reservoir indicates preexisted oil had been cracked into wet gas, and this kind of gas had also been found in gas pools. Heavy isotopic methane is derived from coal at extremely high maturity stage. There may be little inorganic alkane gases in deep layers for their geochemistry and special geological setting of Songliao Basin. Artificial mixing experiments of different origins gases confirm that inorganic gas such as gas from well FS1 mixed with other end members

Prediction and control of rock burst of coal seam contacting gas in deep mining

Energy Technology Data Exchange (ETDEWEB)

En-yuan Wang; Xiao-fei Liu; En-lai Zhao; Zhen-tang Liu [China University of Mining and Technology, Xuzhou (China). School of Safety Engineering

2009-06-15

By analyzing the characteristics and the production mechanism of rock burst that goes with abnormal gas emission in deep coal seams, the essential method of eliminating abnormal gas emission by eliminating the occurrence of rock burst or depressing the magnitude of rock burst was considered. The No.237 working face in Nanshan coal mine was selected as the typical working face contacting gas in deep mining; aimed at this working face, a system of rock burst prediction and control for coal seam contacting gas in deep mining was established using the three-dimensional distinct element code software 3DEC. This system includes three parts: (1) regional prediction of rock burst hazard before mining; (2) local prediction of rock burst hazard during mining; and (3) rock burts control by an electromagnetic radiation method and specific drilling method. 8 refs., 4 figs., 1 tab.

Chaotic characteristic of electromagnetic radiation time series of coal or rock under different scales

Energy Technology Data Exchange (ETDEWEB)

Zhen-Tang Liu; En-Lai Zhao; En-Yuan Wang; Jing Wang [China University of Mining and Technology, Xuzhou (China). School of Safety Engineering

2009-02-15

Based on chaos theory, the chaotic characteristics of electromagnetic radiation time series of coal or rock under different loads was studied. The results show that the correlation of electromagnetic radiation time series of small-scale coal or rock and coal mine converges to a stable saturation value, which shows that these electromagnetic radiation time series have chaos characteristics. When there is danger of coal seam burst, the value of the saturation correlation dimension D{sub 2} of the electromagnetic radiation time series is bigger and it changes greatly; when there is no danger, its value is smaller and changes smoothly. The change of saturation correlation of electromagnetic radiation time series can be used to forecast coal or rock dynamic disasters. 11 refs., 4 figs.

Solid-Gas Coupling Model for Coal-Rock Mass Deformation and Pressure Relief Gas Flow in Protection Layer Mining

OpenAIRE

Zhu, Zhuohui; Feng, Tao; Yuan, Zhigang; Xie, Donghai; Chen, Wei

2018-01-01

The solid-gas coupling model for mining coal-rock mass deformation and pressure relief gas flow in protection layer mining is the key to determine deformation of coal-rock mass and migration law of pressure relief gas of protection layer mining in outburst coal seams. Based on the physical coupling process between coal-rock mass deformation and pressure-relief gas migration, the coupling variable of mining coal-rock mass, a part of governing equations of gas seepage field and deformation fiel...

A case study of long-term geochemical evolution of coal waste rock drainage and its remediation

Energy Technology Data Exchange (ETDEWEB)

Jarvis, A.P.; Gandy, C.J. [Newcastle Univ. (United Kingdom). School of Civil Engineering and Geosciences, Hydrogeochemical Engineering Research and Outreach Group

2010-07-01

The geochemical evolution of drainage from an 35 hectare orphan waste rock pile over a 15-year period was described. Spoil material at the site was generated during coal mining at 2 collieries between 1922 and 1970, and was comprised of grey and black shale, ash, coal, and coal dust. The heap was founded on an impermeable clay layer. Located in northern England, drainage from the rock heap was intercepted by a small compost wetland system installed in 1997. The waste rock heap was selectively capped in 1998. Water samples were collected and analyzed. Anion concentrations were determined using an ion chromatograph. The samples were filtered periodically. Acidity concentrations and flow rates were determined. Results of the study showed measurable improvements in water quality as a result of capping the heap. The study demonstrated that a combination of selective spoil capping and wetland treatment can serve as a low-cost solution to acid mine drainage at some abandoned mine sites. 9 refs., 1 tab., 1 fig.

A case study of long-term geochemical evolution of coal waste rock drainage and its remediation

International Nuclear Information System (INIS)

Jarvis, A.P.; Gandy, C.J.

2010-01-01

The geochemical evolution of drainage from an 35 hectare orphan waste rock pile over a 15-year period was described. Spoil material at the site was generated during coal mining at 2 collieries between 1922 and 1970, and was comprised of grey and black shale, ash, coal, and coal dust. The heap was founded on an impermeable clay layer. Located in northern England, drainage from the rock heap was intercepted by a small compost wetland system installed in 1997. The waste rock heap was selectively capped in 1998. Water samples were collected and analyzed. Anion concentrations were determined using an ion chromatograph. The samples were filtered periodically. Acidity concentrations and flow rates were determined. Results of the study showed measurable improvements in water quality as a result of capping the heap. The study demonstrated that a combination of selective spoil capping and wetland treatment can serve as a low-cost solution to acid mine drainage at some abandoned mine sites. 9 refs., 1 tab., 1 fig.

Pattern Recognition of Signals for the Fault-Slip Type of Rock Burst in Coal Mines

Directory of Open Access Journals (Sweden)

X. S. Liu

2015-01-01

Full Text Available The fault-slip type of rock burst is a major threat to the safety of coal mining, and effectively recognizing its signals patterns is the foundation for the early warning and prevention. At first, a mechanical model of the fault-slip was established and the mechanism of the rock burst induced by the fault-slip was revealed. Then, the patterns of the electromagnetic radiation, acoustic emission (AE, and microseismic signals in the fault-slip type of rock burst were proposed, in that before the rock burst occurs, the electromagnetic radiation intensity near the sliding surface increases rapidly, the AE energy rises exponentially, and the energy released by microseismic events experiences at least one peak and is close to the next peak. At last, in situ investigations were performed at number 1412 coal face in the Huafeng Mine, China. Results showed that the signals patterns proposed are in good agreement with the process of the fault-slip type of rock burst. The pattern recognition can provide a basis for the early warning and the implementation of relief measures of the fault-slip type of rock burst.

Application of nuclear techniques for analysis of Vietnamese coal and embedding rocks

International Nuclear Information System (INIS)

Vo Dac Bang; Pham Van Duong; Nguyen Thanh Binh; Le Tien Quan; Nguyen Manh Hung; Nguyen Thi Hong; Vu Hoang Lam

1995-01-01

In the paper the result of elemental analysis by Nuclear Techniques of Coal and Embedded rocks samples from Vietnamese Quang Ninh and Thai Nguyen basins were presented. Methods used were: Neutron activation Analysis at Dalat Reactor, low counting with HP-Ge and NaJ detectors and X-ray fluorescent analysis with planar Si (Si) detector. Mean concentrations of 19 elements in coal and 9 in rocks were determined. Correlation between concentrations of elements were found. It appears that the correlation between ash content and U, K, Th, concentrations was poor for Quang Ninh antracitecoal. Correlation coefficient was found to be 0,63 for ash range 0-40%. Content of Th in anthracite Quang Ninh coal was much higher than reported in literature for subbituminous, bituminous and lignite coals, while Thai Nguyen fat coal contains considerable amount of Cu, Pb, Zn. Obtained data were useful for evaluation of potential hazard for environment from using coal as fuel for coal fired power plants, for estimation of possibility of using nuclear technique in coal industry in Vietnam. They could be used also for geochemical investigations. The simple of-line coal ash gauge basing on attenuation of soft gamma radiation from Fe-55 was also described. (author). 6 refs, 3 figs, 8 tabs

The impact of the structural features of the rock mass on seismicity in Polish coal mines

Science.gov (United States)

Patyńska, Renata

2017-11-01

The article presents seismic activity induced in the coal mines of the Upper Silesian Coal Basin (GZW) in relation to the locations of the occurrence of rockbursts. The comparison of these measurements with the structural features of the rock mass of coal mines indicates the possibility of estimating the so-called Unitary Energy Expenditure (UEE) in a specific time. The obtained values of UEE were compared with the distribution of seismic activity in GZW mines. The level of seismic activity in the analysed period changed and depended on the intensity of mining works and diverse mining and geological conditions. Five regions, where tremors occurred (Bytom Trough, Main Saddle, Main Trough, Kazimierz Trough, and Jejkowice and Chwałowice Trough) which belong to various structural units of the Upper Silesia were analyzed. It was found out that rock bursts were recorded only in three regions: Main Saddle, Bytom Trough, and Jejkowice and Chwałowice Trough.

Postsedimentary Alterations of Coal-bearing Rocks and New Factors Affecting their Quality and Ingredient Composition as Exemplified by the Akhaltsikhe Brown Coal Deposit (Georgia)

International Nuclear Information System (INIS)

Maghalashvili, G.

2008-01-01

It has been established that in the case when coal-bearing rocks are represented by bentonitic clays, coal undergoes significant alterations, for the bentonitic clays, as a strong absorbent, absorb from the coal under conditions of natural humidity part of organics (humic acids, gums and other moving composite substances) thus depleting the coal, increasing its ash content and accordingly decreasing its calorific capacity. In this case it is expedient to exploit the coal and ''black'' or organics-saturated rocks selectively. It has also been established that the organics-saturated ''black'' bentonite is an excellent organic and mineral fertilizer that has been tested by the autor in the patented man-made soil. At the same time, in the case of coal briquetting, it may be used as a bonding material. (author)

A comparison of geochemical features of extracts from coal-seams source rocks with different polarity solvents

Energy Technology Data Exchange (ETDEWEB)

Chen, Jianping; Deng, Chunping; Wang, Huitong

2009-02-15

There exists a great difference in group-type fractions and biomarker distributions of chloroform extracts from coals and coal-seams oils, which makes the source identification of coal-seams oils in sedimentary basins rather difficult. The experiment, in which four different polarity solvents, n-hexane, benzene, dichloromethane and chloroform, were used to extract 9 coal-seams source rocks and 3 typical lacustrine source rocks, showed that the yield of extracts increased gradually with increasing solvent polarity. The distribution features of their n-alkanes, isoprenoids and sterane and terpane biomarkers remained, in general, similar, showing no distinct enrichment or depletion for a certain fraction by any solvent. The compositional analysis on n-hexane and chloroform extracts showed that the absolute amount (concentration) of biomarkers was relatively low for the n-hexane extract but comparatively high for the chloroform extract, this difference became great among coal-seams source rocks but small among lacustrine mudstones. The statistical analysis on the relative amount of the 18 major biomarkers in n-hexane and chloroform extracts from 10 source rock samples showed that extracts with a proportional error for the same biomarker of less than 5% (including the analytical error) accounted for 84% while those with a proportional error over 10% amounted to below 5%. This suggested that the outcome of oil-source correlation made by these biomarkers will be independent of variations in amounts of saturates and biomarkers arising from solvent polarity. Therefore, biomarkers obtained from organic-rich source rocks including coals by the extraction with the commonly used chloroform solvent can be applied for the oilsource correlation of coal-seams petroliferous basins.

Analytical tools for managing rock fall hazards in Australian coal mine roadways

Energy Technology Data Exchange (ETDEWEB)

Ross Seedsman; Nick Gordon; Naj Aziz [University of Wollongong (Australia)

2009-03-15

This report provides a reference source for the design of ground control measures in coal mine roadways using analytical methods. Collapse models are provided for roof and rib. The roof models recognise that different collapse modes can apply in different stress fields - high, intermediate, and zero compressive stresses. The rib models draw analogies to rock slope stability and also the impact of high vertical stresses. Methods for determining support or reinforcement requirements are provided. Suspension of collapsed masses is identified as the basis for roof support in both very high and zero compressive stress regimes. Reinforcement of bedding discontinuities is advocated for intermediate compressive stresses. For the ribs, restraint of coal blocks defined by pre-existing joints or by mining induced fractures is required.

Study on Roadheader Cutting Load at Different Properties of Coal and Rock

Directory of Open Access Journals (Sweden)

Xueyi Li

2013-01-01

Full Text Available The mechanism of cutting process of roadheader with cutting head was researched, and the influences of properties of coal and rock on cutting load were deeply analyzed. Aimed at the defects of traditional calculation method of cutting load on fully expressing the complex cutting process of cutting head, the method of finite element simulation was proposed to simulate the dynamic cutting process. Aimed at the characteristics of coal and rock which affect the cutting load, several simulations with different firmness coefficient were taken repeatedly, and the relationship between three-axis force and firmness coefficient was derived. A comparative analysis of cutting pick load between simulation results and theoretical formula was carried out, and a consistency was achieved. Then cutting process with a total cutting head was carried out on this basis. The results show that the simulation analysis not only provides a reliable guarantee for the accurate calculation of the cutting head load and improves the efficiency of the cutting head cutting test but also offers a basis for selection of cutting head with different geological conditions of coal or rock.

Modelling temperature-dependent heat production over decades in High Arctic coal waste rock piles

DEFF Research Database (Denmark)

Hollesen, Jørgen; Elberling, Bo; Jansson, P.E.

2011-01-01

Subsurface heat production from oxidation of pyrite is an important process that may increase subsurface temperatures within coal waste rock piles and increase the release of acid mine drainage, AMD. Waste rock piles in the Arctic are especially vulnerable to changes in subsurface temperatures...... such as heat production from coal oxidation may be equally important....... as the release of AMD normally is limited by permafrost. Here we show that temperatures within a 20 year old heat-producing waste rock pile in Svalbard (78°N) can be modelled by the one-dimensional heat and water flow model (CoupModel) with a new temperature-dependent heat-production module that includes both...

Microseismic Precursory Characteristics of Rock Burst Hazard in Mining Areas Near a Large Residual Coal Pillar: A Case Study from Xuzhuang Coal Mine, Xuzhou, China

Science.gov (United States)

Cao, An-ye; Dou, Lin-ming; Wang, Chang-bin; Yao, Xiao-xiao; Dong, Jing-yuan; Gu, Yu

2016-11-01

Identification of precursory characteristics is a key issue for rock burst prevention. The aim of this research is to provide a reference for assessing rock burst risk and determining potential rock burst risk areas in coal mining. In this work, the microseismic multidimensional information for the identification of rock bursts and spatial-temporal pre-warning was investigated in a specific coalface which suffered high rock burst risk in a mining area near a large residual coal pillar. Firstly, microseismicity evolution prior to a disastrous rock burst was qualitatively analysed, and the abnormal clustering of seismic sources, abnormal variations in daily total energy release, and event counts can be regarded as precursors to rock burst. Secondly, passive tomographic imaging has been used to locate high seismic activity zones and assess rock burst hazard when the coalface passes through residual pillar areas. The results show that high-velocity or velocity anomaly regions correlated well with strong seismic activities in future mining periods and that passive tomography has the potential to describe, both quantitatively and periodically, hazardous regions and assess rock burst risk. Finally, the bursting strain energy index was further used for short-term spatial-temporal pre-warning of rock bursts. The temporal sequence curve and spatial contour nephograms indicate that the status of the danger and the specific hazardous zones, and levels of rock burst risk can be quantitatively and rapidly analysed in short time and in space. The multidimensional precursory characteristic identification of rock bursts, including qualitative analysis, intermediate and short-time quantitative predictions, can guide the choice of measures implemented to control rock bursts in the field, and provides a new approach to monitor and forecast rock bursts in space and time.

Use of overburden rocks from open-pit coal mines and waste coals of Western Siberia for ceramic brick production with a defect-free structure

Science.gov (United States)

Stolboushkin, A. Yu; Ivanov, A. I.; Storozhenko, G. I.; Syromyasov, V. A.; Akst, D. V.

2017-09-01

The rational technology for the production of ceramic bricks with a defect-free structure from coal mining and processing wastes was developed. The results of comparison of physical and mechanical properties and the structure of ceramic bricks manufactured from overburden rocks and waste coal with traditional for semi-dry pressing mass preparation and according to the developed method are given. It was established that a homogeneous, defect-free brick texture obtained from overburden rocks of open-pit mines and waste coal improves the quality of ceramic wall materials produced by the method of compression molding by more than 1.5 times compared to the brick with a traditional mass preparation.

Thermal surface characteristics of coal fires 1 results of in-situ measurements

Science.gov (United States)

Zhang, Jianzhong; Kuenzer, Claudia

2007-12-01

Natural underground coal fires are fires in coal seams occurring subsurface. The fires are ignited through a process named spontaneous combustion, which occurs based on a natural reaction but is usually triggered through human interaction. Coal mining activities expose coal to the air. This leads to the exothermal oxidation of the carbon in the coal with the air's oxygen to CO 2 and - under certain circumstances - to spontaneous combustion. Coal fires occur in many countries world wide - however, currently the Chinese coal mining industry faces the biggest problems with coal fires. Coal fires destroy the valuable resource coal and furthermore lead to many environmental degradation phenomena such as the deterioration of surrounding vegetation, land subsidence and the emission of toxic gasses (CO, N 2O). They additionally contribute to the emission of green house relevant gasses such as CO 2 and CH 4 to the atmosphere. In this paper we present thermal characteristics of coal fires as measured in-situ during a field campaign to the Wuda coal fire area in south-central Inner Mongolia, China. Thermal characteristics include temperature anomaly measurements at the surface, spatial surface temperature profiles of fire areas and unaffected background areas, diurnal temperature profiles, and temperature measurements inside of coal fire induced cracks in the overlying bedrock. For all the measurements the effects of uneven solar heating through influences of slope and aspect are considered. Our findings show that coal fires result in strong or subtle thermal surface anomalies. Especially the latter can easily be influenced by heating of the surrounding background material through solar influences. Temperature variation of background rocks with different albedo, slope, aspect or vegetation cover can substantially influence the detectability of thermal anomalies. In the worst case coal fire related thermal anomalies can be completely masked by solar patterns during the daytime

Study on acoustic-electric-heat effect of coal and rock failure processes under uniaxial compression

Science.gov (United States)

Li, Zhong-Hui; Lou, Quan; Wang, En-Yuan; Liu, Shuai-Jie; Niu, Yue

2018-02-01

In recent years, coal and rock dynamic disasters are becoming more and more severe, which seriously threatens the safety of coal mining. It is necessary to carry out an depth study on the various geophysical precursor information in the process of coal and rock failure. In this paper, with the established acoustic-electric-heat multi-parameter experimental system of coal and rock, the acoustic emission (AE), surface potential and thermal infrared radiation (TIR) signals were tested and analyzed in the failure processes of coal and rock under the uniaxial compression. The results show that: (1) AE, surface potential and TIR have different response characteristics to the failure process of the sample. AE and surface potential signals have the obvious responses to the occurrence, extension and coalescence of cracks. The abnormal TIR signals occur at the peak and valley points of the TIR temperature curve, and are coincident with the abnormities of AE and surface potential to a certain extent. (2) The damage precursor points and the critical precursor points were defined to analyze the precursor characteristics reflected by AE, surface potential and TIR signals, and the different signals have the different precursor characteristics. (3) The increment of the maximum TIR temperature after the main rupture of the sample is significantly higher than that of the average TIR temperature. Compared with the maximum TIR temperature, the average TIR temperature has significant hysteresis in reaching the first peak value after the main rapture. (4) The TIR temperature contour plots at different times well show the evolution process of the surface temperature field of the sample, and indicate that the sample failure originates from the local destruction.

Selected elements of rock burst state assessment in case studies from the Silesian hard coal mines

Energy Technology Data Exchange (ETDEWEB)

Jozef Kabiesz; Janusz Makowka [Central Mining Institute, Katowice (Poland)

2009-09-15

Exploitation of coal seams in the Upper Silesian Coal Basin is conducted in complex and difficult conditions. These difficulties are connected with the occurrence of many natural mining hazards and limitations resulting from the existing in this area surface infrastructure. One of the most important problems of Polish mining is the rock burst hazard and reliable evaluation of its condition. During long-years' mining practice in Poland a comprehensive system of evaluation and control of this hazard was developed. In the paper the main aspects of rock burst hazard state evaluation will be presented, comprising: 1) rock mass inclination for rock bursts, i.e., rock strength properties investigation, comprehensive parametric evaluation of rock mass inclination for rock bursts, prognosis of seismic events induced by mining operations, methods of computer-aided modelling of stress and rock mass deformation parameters distribution, strategic rock mass classification under rock burst degrees; 2) immediate seismic and rock burst hazard state evaluation, i.e., low diameter test drilling method, seismologic and seismoacoustic method, comprehensive method of rock burst hazard state evaluation, non-standard methods of evaluation; 3) legal aspects of rock burst hazard state evaluation. Selected elements of the hazard state evaluation system are illustrated with specific practical examples of their application. 11 refs., 14 figs.

Reducing rock fall injuries in underground US coal mines

Energy Technology Data Exchange (ETDEWEB)

Robertson, S.B.; Molinda, G.M.; Pappas, D.M. [Pittsburgh Research Laboratory, Pittsburgh, PA (United States)

2005-07-01

A continuing risk to underground US coal miners is rock falling from the mine roof. Almost 99% of injuries caused by rock falls are not from a major roof collapse, but from smaller rock that fall from between roof bolts. Installing roof screen provides excellent overhead roof coverage and dramatically reduces the potential for rock fall injuries, especially to roof bolted operators. The National Institute for Occupational Safety and Health (NIOSH) has explored different installation techniques and roof screening options along with machine design innovations that make roof screening easier and safer. Applying ergonomic principles to roof screening will offer insight and direction for better material handling. Other techniques for controlling rock falls and roof falls for long-term stability include the application of surface support liners and polyurethane (PUR) injection. An ongoing study at the NIOSH Lake Lynn Laboratory of various types of spray-on liner and shotcrete materials is providing a unique opportunity to evaluate the long-term behaviour of liners in an underground environment. In-mine studies of PUR have involved pre- and post-injection core drilling and video borecole logging. The results have provided insights into how PUR penetrates and reinforces weak and highly fractured rock. 11 refs., 8 figs., 1 tab.

Rock Mechanics Studies During Continuous Miner Bases Coal Pillar Extraction in Indian Coalfields

Czech Academy of Sciences Publication Activity Database

Ram, S.; Kumar, D.; Koníček, Petr; Singh, A. K.; Kumar, R.; Singh, A. Kr.; Singh, R.

2015-01-01

Roč. 111, April 2014-March 2015 (2015), s. 89-104 ISSN 0254-8003 Institutional support: RVO:68145535 Keywords : mining * mechanized depillaring scenario * rock mechanics Subject RIV: DH - Mining, incl. Coal Mining

Deformation properties of sedimentary rocks in the process of underground coal gasification

Directory of Open Access Journals (Sweden)

Mirosława Bukowska

2015-01-01

Full Text Available The article presents results of research into changes in deformation properties of rocks, under influence of temperature, during the process of underground coal gasification. Samples of carboniferous sedimentary rocks (claystones and sandstones, collected in different areas of Upper Silesian Coal Basin (GZW, were heated at the temperature of between 100 and 1000–1200 °C, and then subjected to uniaxial compression tests to obtain a full stress-strain curves of the samples and determine values of residual strain and Poisson's ratio. To compare the obtained values of deformation parameters of rocks, tested in dry-air state and after heating in a given range of temperature, normalised values of residual strain and Poisson's ratio were determined. Based on them, coefficient of influence of temperature on tested deformation parameters was determined. The obtained values of the coefficient can be applied in mining practice to forecast deformability of gangue during underground coal gasification, when in the direct surrounding of a georeactor there are claystones or sandstones. The obtained results were analysed based on classification of uniaxial compression strength of GZW gangue, which formed the basis for dividing claystones and sandstones into very low, low, medium and high uniaxial compression strength rocks. Based on the conducted tests it was concluded that the influence of uniaxial compression strength on the value of residual strain, unlike the influence of grain size of sandstones, is unambiguous within the range of changes in the parameter. Among claystones changes in the value of Poisson's ratio depending on their initial strength were observed. Sandstones of different grain size either increased or decreased the value of Poisson's ratio in comparison with the value determined at room temperature in dry-air conditions.

Investigations into stress shell characteristics of surrounding rock in fully mechanized top-coal caving face

Energy Technology Data Exchange (ETDEWEB)

Xie, G.X.; Chang, J.C.; Yang, K. [Anhui University of Science and Technology, Huainan (China)

2009-01-15

A key issue in underground mining is to understand and master the evolving patterns of stress induced by mining, and to control and utilize the action of rock pressure. Numerical and physical modeling tests have been carried out to investigate the distribution patterns of stress in the rock surrounding a fully mechanized top-coal caving (FMTC) face. The results showed that a macro-stress shell composed of high stress exists in the rock surrounding an FMTC face. The stress of the shell is higher than its internal and external stress and the stresses at its skewback producing abutment pressure for the surrounding rock. The stress shell lies in the virgin coal and rock mass in the vicinity of the face and its sagging zone. The stress shell, which bears and transfers the loads of overlying strata, acts as the primary supporting system of forces, and is the corpus of characterizing three-dimensional and macro-rock pressure distribution of mining face. Its external and internal shape changes with the variations in the working face structure as the face advances. Within the low-stress zone inside the stress shell, another structure, i.e. voussoir beam, which only bears parts of the load from the lower-lying strata, will produce periodic pressures on the face instead of great dynamic pressure even if the beam ruptures and loses stability. The results show that the FMTC face is situated within the lower-stress zone, which is protected by the stress shell of the overlying surrounding rock. We give an explanation of lower occurrence of rock pressure on FMTC faces, and reveal the mechanical nature of the top coal of an FMTC face acting as a 'cushion'. The strata behaviors of the face and its neighboring gates are under control of the stress shell. Drastic rock pressure in mine may occur when the balance of the stress shell is destruction or the forces system of the stress shell transfers. Crown Copyright

Upper Paleozoic coal measures and unconventional natural gas systems of the Ordos Basin, China

Directory of Open Access Journals (Sweden)

Xuan Tang

2012-11-01

Full Text Available Upper Paleozoic coal measures in the Ordos Basin consist of dark mudstone and coal beds and are important source rocks for gas generation. Gas accumulations include coal-bed methane (CBM, tight gas and conventional gas in different structural areas. CBM accumulations are mainly distributed in the marginal area of the Ordos Basin, and are estimated at 3.5 × 1012 m3. Tight gas accumulations exist in the middle part of the Yishan Slope area, previously regarded as the basin-centered gas system and now considered as stratigraphic lithologic gas reservoirs. This paper reviews the characteristics of tight gas accumulations: poor physical properties (porosity < 8%, permeability < 0.85 × 10−3 μm2, abnormal pressure and the absence of well-defined gas water contacts. CBM is a self-generation and self-reservoir, while gas derived from coal measures migrates only for a short distance to accumulate in a tight reservoir and is termed near-generation and near-reservoir. Both CBM and tight gas systems require source rocks with a strong gas generation ability that extends together over wide area. However, the producing area of the two systems may be significantly different.

Analysis of mercury in rock varnish samples in areas impacted by coal-fired power plants

International Nuclear Information System (INIS)

Nowinski, Piotr; Hodge, Vernon F.; Gerstenberger, Shawn; Cizdziel, James V.

2013-01-01

Rock varnish is a manganese–iron rich coating that forms on rocks, most often in arid climates. To assess its utility as an environmental monitor of mercury contamination, cold vapor atomic absorption spectrometry (CVAAS) was used for analysis. Samples were collected in the fallout patterns of two coal-fired power plants in southern Nevada: the defunct Mohave Power Plant (MPP) and the operating Reid Gardner Power Plant (RGPP). The resultant Hg concentrations in rock varnishes were plotted as a function of the distance from each power plant. The highest concentrations of Hg occurred at locations that suggest the power plants are the main source of pollutants. In addition, past tracer plume studies carried out at MPP show that the highest tracer concentrations coincide with the highest rock varnish Hg concentrations. However, additional samples are required to further demonstrate that power plants are indeed the sources of mercury in varnishes. -- Highlights: •We analyze desert varnish samples collected in the fallout patterns of two coal-fired and analyzed for Hg by CVAA. •The resultant Hg concentrations in the desert varnish samples were plotted as a function of the distance from each power plant. •The highest concentrations of Hg occurred at locations that suggest the power plants are the main source of pollutants. •Data indicate the utility of desert varnish as a passive environmental monitor for Hg atmospheric pollution. -- Cold vapor atomic absorption spectrometry (CVAAS) was used for analysis of mercury in varnished rocks collected in the fallout zones of two coal-fired power plants

Influence of stress on the permeability of coal and sedimentary rocks of the Upper Silesian Basin

Czech Academy of Sciences Publication Activity Database

Konečný, Pavel; Kožušníková, Alena

2011-01-01

Roč. 48, č. 2 (2011), s. 347-352 ISSN 1365-1609 Institutional research plan: CEZ:AV0Z30860518 Keywords : permeability * triaxial test * coal and sedimentary rocks Subject RIV: DH - Mining, incl. Coal Mining Impact factor: 1.272, year: 2011 http://www.sciencedirect.com/science/article/pii/S1365160910002194

Modelling of Gas Flow in the Underground Coal Gasification Process and its Interactions with the Rock Environment

Directory of Open Access Journals (Sweden)

Tomasz Janoszek

2013-01-01

Full Text Available The main goal of this study was the analysis of gas flow in the underground coal gasification process and interactions with the surrounding rock mass. The article is a discussion of the assumptions for the geometric model and for the numerical method for its solution as well as assumptions for modelling the geochemical model of the interaction between gas-rock-water, in terms of equilibrium calculations, chemical and gas flow modelling in porous mediums. Ansys-Fluent software was used to describe the underground coal gasification process (UCG. The numerical solution was compared with experimental data. The PHREEQC program was used to describe the chemical reaction between the gaseous products of the UCG process and the rock strata in the presence of reservoir waters.

Characterization of coal-derived hydrocarbons and source-rock potential of coal beds, San Juan Basin, New Mexico and Colorado, U.S.A.

Science.gov (United States)

Rice, D.D.; Clayton, J.L.; Pawlewicz, M.J.

1989-01-01

Coal beds are considered to be a major source of nonassociated gas in the Rocky Mountain basins of the United States. In the San Juan basin of northwestern New Mexico and southwestern Colorado, significant quantities of natural gas are being produced from coal beds of the Upper Cretaceous Fruitland Formation and from adjacent sandstone reservoirs. Analysis of gas samples from the various gas-producing intervals provided a means of determining their origin and of evaluating coal beds as source rocks. The rank of coal beds in the Fruitland Formation in the central part of the San Juan basin, where major gas production occurs, increases to the northeast and ranges from high-volatile B bituminous coal to medium-volatile bituminous coal (Rm values range from 0.70 to 1.45%). On the basis of chemical, isotopic and coal-rank data, the gases are interpreted to be thermogenic. Gases from the coal beds show little isotopic variation (??13C1 values range -43.6 to -40.5 ppt), are chemically dry (C1/C1-5 values are > 0.99), and contain significant amounts of CO2 (as much as 6%). These gases are interpreted to have resulted from devolatilization of the humic-type bituminous coal that is composed mainly of vitrinite. The primary products of this process are CH4, CO2 and H2O. The coal-generated, methane-rich gas is usually contained in the coal beds of the Fruitland Formation, and has not been expelled and has not migrated into the adjacent sandstone reservoirs. In addition, the coal-bed reservoirs produce a distinctive bicarbonate-type connate water and have higher reservoir pressures than adjacent sandstones. The combination of these factors indicates that coal beds are a closed reservoir system created by the gases, waters, and associated pressures in the micropore coal structure. In contrast, gases produced from overlying sandstones in the Fruitland Formation and underlying Pictured Cliffs Sandstone have a wider range of isotopic values (??13C1 values range from -43.5 to -38

Anthropogenic soils on spoil rock banks in North Bohemian Coal Basin, Czech Republic

International Nuclear Information System (INIS)

Raclavska, H.; Raclavsky, K.; Matysek, D.; Stalmachova, B.

1997-01-01

The area of the North Bohemian Coal Basin is devastated by the extensive exploitation of brown coal by open pit mining. Knowledge of newly formed soils, their properties, development and contamination is important from the point of view of biological regeneration of the landscape. The mineralogy of anthropogenic soils from the mining area is presented together with the geochemistry of nutrients and trace elements. Attention is paid to the soil-forming processes in the non-reclaimed spoil rock banks with the development of spontaneous vegetation. 3 refs., 1 fig., 4 tabs

Revised models for hydrocarbon generation, migration and accumulation in Jurassic coal measures of the Turpan basin, NW China

Energy Technology Data Exchange (ETDEWEB)

Li Maowen; Stasiuk, L.D. [Geological Survey of Canada, Calgary, Alberta (Canada); Bao Jianping [Jianghan Petroleum University, Hubei (China); Lin, R. [Petroleum University (Beijing), Changping (China); Yuan Mingsheng [PetroChina Tu-Ha Oilfield Company, Xingjiang (China)

2001-07-01

Whether or not the Lower-Middle Jurassic coal measures in the Turpan basin of NW China have generated commercial quantities of liquid petroleums is a problem of considerable importance that remains contentious as it has not yet been resolved unequivocally. This study provides evidence against the Jurassic humic coals as the only major source for the oils discovered in the Taibei depression of this basin and suggests additional significant contributions from the Upper Permian and Middle-Lower Jurassic lacustrine source rocks. The Carboniferous-Permian marine source rocks may have been important also in limited locations along the major basement faults. Molecular and petrographic data indicate that the majority of the Middle Jurassic strata are currently immature or marginally mature with respect to hydrocarbon generation. Within the major depocenters, the Middle-Lower Jurassic coal-bearing strata of the Baodaowan and Xishanyao formations has reached the conventional oil window (i.e. with vitrinite reflectance >0.7 per cent Ro). Pre-Jurassic (Upper Permian in particular) derived hydrocarbons appear to be widespread in extracts of fractured Jurassic coal and fine-grained rocks. Large differences have been observed in the absolute concentrations of biomarker compounds in rock extracts of various source intervals. Thus, 'coaly' biomarker signatures of the oils most likely resulted from mixing and migration contamination when hydrocarbons derived from mature source rocks migrated up through highly fractured coal seams along deep-seated faults. In addition to conventional exploration targets, revised petroleum generation and accumulation models predict that the focus in the Turpan basin should also include deep structures within the Carboniferous-Permian strata and subtle, low magnitude anticlines and stratigraphic traps within thr Triassic-Jurassic sections. (author)

Anthracite like coal in the rock of the late Precambrian. [Australia

Energy Technology Data Exchange (ETDEWEB)

Dojcinov, D; Pavlovic, N Z; Premovic, P I

1983-01-01

The rock of the late Precambrian formation of Paradise Creek (the age is approximately 1.6 million years, Kingsland, Australia) contains an unusually large volume of paramagnetic varieties with properties of free radicals. The presence in this deposit of such varieties confirms the presence in the anthracite coal material of inclusions of primitive protovascular plants of the early Proterozoa in the region of Paradise Creek, Australia.

Control Mechanism of Rock Burst in the Floor of Roadway Driven along Next Goaf in Thick Coal Seam with Large Obliquity Angle in Deep Well

Directory of Open Access Journals (Sweden)

Yunhai Cheng

2015-01-01

Full Text Available This paper deals with the theoretical aspects combined with stress analysis over the floor strata of coal seam and the calculation model for the stress on the coal floor. Basically, this research presents the relevant results obtained for the rock burst prevention in the floor of roadway driven along next goaf in the exploitation of thick coal seam with large obliquity in deep well and rock burst tendency. The control mechanism of rock burst in the roadway driven along next goaf is revealed in the present work. That is, the danger of rock burst can be removed by changing the stress environment for the energy accumulation of the floor and by reducing the impact on the roadway floor from the strong dynamic pressure. This result can be profitable being used at the design stage of appropriate position of roadway undergoing rock burst tendency in similar conditions. Based on the analysis regarding the control mechanism, this paper presents a novel approach to the prevention of rock burst in roadway floor under the above conditions. That is, the return airway is placed within the goaf of the upper working face that can prevent the rock burst effectively. And in this way, mining without coal pillar in the thick coal seam with large obliquity and large burial depth (over a thousand meters is realized. Practice also proves that the rock burst in the floor of roadway driven along next goaf is controlled and solved.

Applying Rock Engineering Systems (RES approach to Evaluate and Classify the Coal Spontaneous Combustion Potential in Eastern Alborz Coal Mines

Directory of Open Access Journals (Sweden)

Amir Saffari

2013-12-01

Full Text Available Subject analysis of the potential of spontaneous combustion in coal layers with analytical and numerical methods has been always considered as a difficult task because of the complexity of the coal behavior and the number of factors influencing it. Empirical methods, due to accounting for certain and specific factors, have not accuracy and efficiency for all positions. The Rock Engineering Systems (RES approach as a systematic method for analyzing and classifying is proposed in engineering projects. The present study is concerned with employing the RES approach to categorize coal spontaneous combustion in coal regions. Using this approach, the interaction of parameters affecting each other in an equal scale on the coal spontaneous combustion was evaluated. The Intrinsic, geological and mining characteristics of coal seams were studied in order to identifying important parameters. Then, the main stages of implementation of the RES method i.e. interaction matrix formation, coding matrix and forming a list category were performed. Later, an index of Coal Spontaneous Combustion Potential (CSCPi was determined to format the mathematical equation. Then, the obtained data related to the intrinsic, geological and mining, and special index were calculated for each layer in the case study (Pashkalat coal region, Iran. So, the study offers a perfect and comprehensive classification of the layers. Finally, by using the event of spontaneous combustion occurred in Pashkalat coal region, an initial validation for this systematic approach in the study area was conducted, which suggested relatively good concordance in Pashkalat coal region.

Correlation chart of Pennsylvanian rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania showing approximate position of coal beds, coal zones, and key stratigraphic units: Chapter D.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Trippi, Michael H.; Slucher, Ernie R.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

The Appalachian basin, one of the largest Pennsylvanian bituminous coal-producing regions in the world, currently contains nearly one-half of the top 15 coal-producing States in the United States (Energy Information Agency, 2006). Anthracite of Pennsylvanian age occurs in synclinal basins in eastern Pennsylvania, but production is minimal. A simplified correlation chart was compiled from published and unpublished sources as a means of visualizing currently accepted stratigraphic relations between the rock formations, coal beds, coal zones, and key stratigraphic units in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania. The thickness of each column is based on chronostratigraphic divisions (Lower, Middle, and Upper Pennsylvanian), not the thickness of strata. Researchers of Pennsylvanian strata in the Appalachian basin also use biostratigraphic markers and other relative and absolute geologic age associations between the rocks to better understand the spatial relations of the strata. Thus, the stratigraphic correlation data in this chart should be considered provisional and will be updated as coal-bearing rocks within the Appalachian coal regions continue to be evaluated.

Deformation mechanisms in a coal mine roadway in extremely swelling soft rock.

Science.gov (United States)

Li, Qinghai; Shi, Weiping; Yang, Renshu

2016-01-01

The problem of roadway support in swelling soft rock was one of the challenging problems during mining. For most geological conditions, combinations of two or more supporting approaches could meet the requirements of most roadways; however, in extremely swelling soft rock, combined approaches even could not control large deformations. The purpose of this work was to probe the roadway deformation mechanisms in extremely swelling soft rock. Based on the main return air-way in a coal mine, deformation monitoring and geomechanical analysis were conducted, as well as plastic zone mechanical model was analysed. Results indicated that this soft rock was potentially very swelling. When the ground stress acted alone, the support strength needed in situ was not too large and combined supporting approaches could meet this requirement; however, when this potential released, the roadway would undergo permanent deformation. When the loose zone reached 3 m within surrounding rock, remote stress p ∞ and supporting stress P presented a linear relationship. Namely, the greater the swelling stress, the more difficult it would be in roadway supporting. So in this extremely swelling soft rock, a better way to control roadway deformation was to control the releasing of surrounding rock's swelling potential.

Rock mechanics investigations of structural stability in the Bulli seam at West Cliff Colliery

Energy Technology Data Exchange (ETDEWEB)

Jaggar, F

1978-03-01

Rock mechanics investigations were conducted at West Cliff colliery to obtain rock properties and stress measurements and study the stability of mining structures. The roof and floor were drilled in order to obtain core for rock testing and lump samples of coal were collected in order to measure the coal properties. Absolute stress measurements were obtained using CSIR cells. The strata were sufficiently uniform and competent to overcore the emplaced cells. Testing revealed that the rocks were better than average for coal measure sedimentary strata and the stresses indicated the existence of a moderately high horizontal stress field. The coal is of average strength only with some marked variation relating to the very banded nature of the seam. Finite element analyses showed that the rectangular roadways driven using roof bolts and timber supports were stable and adequately stable by an indicative factor of safety of about l.5.

75 FR 57849 - Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines

Science.gov (United States)

2010-09-23

... correlation between higher job risk and higher wages, suggesting that employees demand monetary compensation... DEPARTMENT OF LABOR Mine Safety and Health Administration 30 CFR Part 75 RIN 1219-AB76 Maintenance of Incombustible Content of Rock Dust in Underground Coal Mines AGENCY: Mine Safety and Health...

Mechanical characteristics of fully mechanized top-coal caving face and surrounding rock stress shell

Energy Technology Data Exchange (ETDEWEB)

Xie Guang-xiang [Anhui University of Science and Technology, Huainan (China)

2005-06-15

The distribution of surrounding rock stress in fully mechanized top-coal caving (FMTC) face was fully researched by large-scale and non-linear three-dimensional numerical simulation and equivalent laboratory. The results show that, there is the structure that is made of macroscopical stress shell composed of high stress binds in overlying strata of FMTC face. Stress shell, which bears and pass load of overlying strata, is primary supporting body. The stress in skewback of stress shell forms abutment pressure of surrounding rock in vicinity of working face. Bond-beam structure lies in reducing zone under stress shell. It only bear partial burden of strata under stress shell. The uppermost mechanical characteristic of FMTC face is lying in the low stress area under stress shell. It is the essential cause of strata behaviors of FMTC face relaxation. On the basis of analyzing stress shell, the mechanical essence that top coal performs a function of bedding is demonstrated. 4 refs., 7 figs.

Depositional controls on coal distribution and quality in the Eocene Brunner Coal Measures, Buller Coalfield, South Island, New Zealand

Science.gov (United States)

Flores, R.M.; Sykes, R.

1996-01-01

The Buller Coalfield on the West Coast of the South Island, New Zealand, contains the Eocene Brunner Coal Measures. The coal measures unconformably overlie Paleozoic-Cretaceous basement rocks and are conformably overlain by, and laterally interfinger with, the Eocene marine Kaiata Formation. This study examines the lithofacies frameworks of the coal measures in order to interpret their depositional environments. The lower part of the coal measures is dominated by conglomeratic lithofacies that rest on a basal erosional surface and thicken in paleovalleys incised into an undulating peneplain surface. These lithofacies are overlain by sandstone, mudstone and organic-rich lithofacies of the upper part of the coal measures. The main coal seam of the organic-rich lithofacies is thick (10-20 m), extensive, locally split, and locally absent. This seam and associated coal seams in the Buller Coalfield are of low- to high-volatile bituminous rank (vitrinite reflectance between 0.65% and 1.75%). The main seam contains a variable percentage of ash and sulphur. These values are related to the thickening and areal distribution of the seam, which in turn, were controlled by the nature of clastic deposition and peat-forming mire systems, marine transgression and local tidal incursion. The conglomeratic lithofacies represent deposits of trunk and tributary braided streams that rapidly aggraded incised paleovalleys during sea-level stillstands. The main seam represents a deposit of raised mires that initially developed as topogenous mires on abandoned margins of inactive braidbelts. Peat accumulated in mires as a response to a rise in the water table, probably initially due to gradual sea-level rise and climate, and the resulting raised topography served as protection from floods. The upper part of the coal measures consists of sandstone lithofacies of flu vial origin and bioturbated sandstone, mudstone and organic-rich lithofacies, which represent deposits of paralic (deltaic

Preliminary evaluation of lithology and quality of coal and embedding rock on the basis of borehole logging data

International Nuclear Information System (INIS)

Nguyen Dinh Chau; Chrusciel, E.

1990-01-01

A simple computer method of interpretation of classic borehole logging made on coal deposits is presented. This interpretation enables fast determination of calorific value, ash content and moisture content of coal as well as shale content, porosity and sandstone matrix content of embedding rocks. A method of graphic representation of results is also shown. 5 figs., 1 tab., 13 refs. (author)

Coal rank (vitrinite reflectance) data for Cretaceous/Tertiary coal measures in the Grande Cache and Hinton areas, Alberta

Energy Technology Data Exchange (ETDEWEB)

Kalkreuth, W.D.; Langenberg, W.; McMechan, M.E.; Tomica, M.A.; McDougall, W.; Burchard, K.

1996-07-01

A total of 544 vitrinite reflectance values are reported. The outcrop locations and other pertinent data are listed. Vitrinite reflectances determined in subsurface samples from two coal exploration boreholes and 13 petroleum exploration wells are tabulated. The data have been used (in other studies) to evaluate maturation levels in potential source rocks and to assess methane potential of the coal deposits. A diskette containing the data is included. 18 refs., 1 fig., 2 tabs.

Pillar size optimization design of isolated island panel gob-side entry driving in deep inclined coal seam—case study of Pingmei No. 6 coal seam

Science.gov (United States)

Zhang, Shuai; Wang, Xufeng; Fan, Gangwei; Zhang, Dongsheng; Jianbin, Cui

2018-06-01

There is a perception that deep roadways are difficult to maintain. To reverse this and to improve the recovery rate of coal resources, gob-side entry driving is widely used in coal mines, especially deep-mining coal mines, in China. Determination of the reasonable pillar size through in situ observation and experimentation plays a vital role for roadway maintenance. Based on the geological conditions of Pingmei No.6 coal seam, a theoretical analysis, numerical simulation, and industrial experiments are carried out to calculate the reasonable width of chain pillars, analyze the lateral support stress distribution law near the gob side, investigate the relationship between the coal pillar stress distribution, roadway surrounding rock stress distribution, roadway surrounding rock deformation and the coal pillar width. The results indicate that 5 m wide coal pillars can ensure that the chain pillars are at a lower stress level and the deformation of roadway surrounding rock is in a more reasonable range. Industrial experiments show that when the chain pillar width is 5 m, the deformation of roadway surrounding rock can meet the requirements of working face safe production. The numerical results agreed well with field measurement and observations, and the industrial experiments results further validated the results of the numerical simulation.

Preliminary Result of Geophysical Some Studieson the Nariinsukhait Coal Deposit

Science.gov (United States)

Norov, B.; Purevjav, N.; Roy, D. K., Sr.

2017-12-01

Nariinsukhait coal deposit has a strategic importance on Mongolian national economic development. The deposit is located in Gurvan-tes of the Umnu-gobi province, as 849 km south-west away from Ulaanbaatar. The deposit in geographically, belongs to Gobi Altai region region of the Altai mountain region. The area contains Permian, Cretaceous, Jurassic, Triassic age of sediments. Sediments are red or sedimentary cover on some part of area (Minjin. Ch., Batnyam. D., Rentsendorj. S (Baatarkhuyag. A., Altantsetseg. D., 2015). The coal deposit is located in the center portion of the Nariinsukhait basin. The age of coal hosted sedimentary rock is Jurassic estimated by Paleo-botanic methodology, using examination of a total 59 kind of plants, 288 pollen grains (Baatarkhuyag. A., Altantsetseg. D., 2015). The thickness of coal hosted sedimentary sequence is approximately 1105.5m and named as Orgilohbulag formation. In case of geophysical exploration, preliminary interpretation of the coal basin has been done by 3 geophysical methodologies which commonly applying during exploration stage of coal. The interpretations are given below. Natural Gamma Sonde /NGRS 4140/: use to determine natural gamma activation on rock by radionuclides content (238U; 235U; 232Th; 40K). During measurements well contrasted coal bedding and, value indicate between 0-15cps. And depending on the rock type it has been changed, in case of siltstone, argillite, conglomerate value fluctuated between 15-40cps. However, those rocks natural gamma values are difference little, therefore not showing much contrast between rock types. Formation Density Sonde Version B /FDSB 4036/: The Nariinsukhait coal deposit Open holes and protective pipes of density is 0.5-1.5 g/cm3, 1.2-2.3 g/cm3 respectively. Not well contrasted during measurement due to some of sedimentary rock density range is so low as such sandstone, siltstone, and conglomerate. Therefore, applied resistivity methodology and done interpretation. DLL3

Spot testing on mechanical characteristics of surrounding rock in gates of fully mechanized top-coal caving face

Energy Technology Data Exchange (ETDEWEB)

Xie Guang-xiang; Yang Ke; Chang Ju-cai [Anhui University of Science and Technology, Anhui (China). Department of Resource Exploration and Management Engineering

2006-07-01

The distribution patterns of mechanical characteristics for surrounding rock in the gateways of fully mechanized top-coal caving (FMTC) face were put forward by analyzing deep displacement, surface displacement, stress distribution and supports loading. The results show that the surrounding rock of the gateways lies in abutment pressure decrease zone near the working face, so that the support load decreases. But the deformations of supports and surrounding rock are very acute. The deformation of surrounding rock appears mainly in abutment pressure influence zone. Reasonable roadway supporting should control the deformation of surrounding rock in intense stage of mining influence. Supporting design ideas of tailentry and head entry should be changed from loading control to deformation control. 8 refs., 10 figs., 1 tab.

Measuring ash content of coal

International Nuclear Information System (INIS)

Clayton, C.G.; Wormald, M.R.

1980-01-01

An apparatus for measuring the ash content of coal is claimed. It comprises a means for irradiating a known quantity of coal in a transport container with a known dose of neutrons, a means for detecting γ-rays having a predetermined energy emitted by the irradiated coal, the γ-rays being indicative of the presence of an ash-forming element in the coal, a means for producing a signal related to the intensity of the γ-ray emission and a means responsive to the signal to provide an indication of the concentration of the ash-forming element in the coal

Nonlinear Dynamics Mechanism of Rock Burst Induced by the Instability of the Layer-Crack Plate Structure in the Coal Wall in Deep Coal Mining

Directory of Open Access Journals (Sweden)

Yanlong Chen

2017-01-01

Full Text Available The instability of layer-crack plate structure in coal wall is one of the causes of rock burst. In the present paper, we investigate the formation and instability processes of layer-crack plate structure in coal wall by experiments and theoretical analysis. The results reveal that layer-crack plate structure formed near the free surface of the coal wall during the loading. During the formation of the layer-crack plate structure, the lateral displacement curve of the coal wall experiences a jagged variation, which suggests the nonlinear instability failure of the coal wall with a sudden release of the elastic energy. Then, a dynamic model for the stability analysis of the layer-crack plate structure was proposed, which takes consideration of the dynamic disturbance factor. Based on the dynamic model, the criterion for dynamic instability of the layer-crack plate structure was determined and demonstrated by an example. According to the analytical results, some control methods of dynamic stability of the layer-crack plate structure was put forward.

Formation and retention of methane in coal

Energy Technology Data Exchange (ETDEWEB)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

Study on Monitoring Rock Burst through Drill Pipe Torque

Directory of Open Access Journals (Sweden)

Zhonghua Li

2015-01-01

Full Text Available This paper presents a new method to identify the danger of rock burst from the response of drill pipe torque during drilling process to overcome many defects of the conventional volume of drilled coal rubble method. It is based on the relationship of rock burst with coal stress and coal strength. Through theoretic analysis, the change mechanism of drill pipe torque and the relationship of drill pipe torque with coal stress, coal strength, and drilling speed are investigated. In light of the analysis, a new device for testing drill pipe torque is developed and a series of experiments is performed under different conditions; the results show that drill pipe torque linearly increases with the increase of coal stress and coal strength; the faster the drilling speed, the larger the drill pipe torque, and vice versa. When monitoring rock burst by drill pipe torque method, the index of rock burst is regarded as a function in which coal stress index and coal strength index are principal variables. The results are important for the forecast of rock burst in coal mine.

German planning atlas. Vol. 1: North Rhine Westphalia. No. 11. Brown coal 2 - ownership of brown coal deposits, resettlement, surface balance, coal, rock, and energy economy, future developments. Deutscher Planungsatlas. Bd. 1: Nordrhein-Westfalen. Nr. 11. Braunkohle 2 - Feldesbesitz, Umsiedlung, Grundwasser, Flaechenbilanz, Kohle-, Abraum- und Energiewirtschaft, kuenftige Entwicklung

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

In map No. III of the atlas on the develpment of Rhenish coal mining, the ownership in brown coal deposits and planning, resettlement, ground water and an area balance are presented. Map No. IV discusses coal economy, rock economy, energy economy, structure and development. Details are described in the text.

Rock burst governance of working face under igneous rock

Science.gov (United States)

Chang, Zhenxing; Yu, Yue

2017-01-01

As a typical failure phenomenon, rock burst occurs in many mines. It can not only cause the working face to cease production, but also cause serious damage to production equipment, and even result in casualties. To explore how to govern rock burst of working face under igneous rock, the 10416 working face in some mine is taken as engineering background. The supports damaged extensively and rock burst took place when the working face advanced. This paper establishes the mechanical model and conducts theoretical analysis and calculation to predict the fracture and migration mechanism and energy release of the thick hard igneous rock above the working face, and to obtain the advancing distance of the working face when the igneous rock fractures and critical value of the energy when rock burst occurs. Based on the specific conditions of the mine, this paper put forward three kinds of governance measures, which are borehole pressure relief, coal seam water injection and blasting pressure relief.

The detection of the coal roof interface by use of high pressure water

Science.gov (United States)

1981-01-01

A device whereby water jets can be used to detect the interface between coal and the overlying roof rock is described. Once this identification is made this distance can be measured using instruments such as the autofocus systems recently developed in the photographic industry. Experiments carried out show that the device can discriminate between coal and rock at coal thicknesses up to 8 inches. An autofocus system was examined which indicates accuracies of better than 0.1 inches.

Low-activity spectrometric gamma-ray logging technique for delineation of coal/rock interfaces in dry blast holes

International Nuclear Information System (INIS)

Asfahani, J.; Borsaru, M.

2007-01-01

A low-activity spectrometric gamma-ray logging technique is proposed in this paper as a sensitive tool for the delineation of coal/rock interfaces in dry blast holes. The advantages and superiority of this technique over traditional micro-density non-spectrometric gamma-ray tools are demonstrated

Rock Burst Monitoring by Integrated Microseismic and Electromagnetic Radiation Methods

Science.gov (United States)

Li, Xuelong; Wang, Enyuan; Li, Zhonghui; Liu, Zhentang; Song, Dazhao; Qiu, Liming

2016-11-01

For this study, microseismic (MS) and electromagnetic radiation (EMR) monitoring systems were installed in a coal mine to monitor rock bursts. The MS system monitors coal or rock mass ruptures in the whole mine, whereas the EMR equipment monitors the coal or rock stress in a small area. By analysing the MS energy, number of MS events, and EMR intensity with respect to rock bursts, it has been shown that the energy and number of MS events present a "quiet period" 1-3 days before the rock burst. The data also show that the EMR intensity reaches a peak before the rock burst and this EMR intensity peak generally corresponds to the MS "quiet period". There is a positive correlation between stress and EMR intensity. Buckling failure of coal or rock depends on the rheological properties and occurs after the peak stress in the high-stress concentration areas in deep mines. The MS "quiet period" before the rock burst is caused by the heterogeneity of the coal and rock structures, the transfer of high stress into internal areas, locked patches, and self-organized criticality near the stress peak. This study increases our understanding of coal and rock instability in deep mines. Combining MS and EMR to monitor rock burst could improve prediction accuracy.

Observer-based Coal Mill Control using Oxygen Measurements

DEFF Research Database (Denmark)

Andersen, Palle; Bendtsen, Jan Dimon; S., Tom

2006-01-01

This paper proposes a novel approach to coal flow estimation in pulverized coal mills, which utilizes measurements of oxygen content in the flue gas. Pulverized coal mills are typically not equipped with sensors that detect the amount of coal injected into the furnace. This makes control...... of the coal flow difficult, causing stability problems and limits the plant's load following capabilities. To alleviate this problem without having to rely on expensive flow measurement equipment, a novel observer-based approach is investigated. A Kalman filter based on measurements of combustion air flow led...... into the furnace and oxygen concentration in the flue gas is designed to estimate the actual coal flow injected into the furnace. With this estimate, it becomes possible to close an inner loop around the coal mill itself, thus giving a better disturbance rejection capability. The approach is validated against...

Rock burst prevention at steep seam mining

Energy Technology Data Exchange (ETDEWEB)

Efremov, G D

1988-09-01

At steep shield longwalls one method of preventing rock bursts is to avoid sharp angles during working. Stress in coal and rock body that appears when steep seams are worked where rock bursts occur at corners of set-up entries is discussed. The dynamic interaction between gas and rock pressure is assessed. Maintains that in order to avoid rock bursts at these places it is necessary to turn the protruding coal wall by 20-30 degrees towards the coal body to divert the action of shift forces. At the same time the face should also be inclined (by 10-15 degrees) to move the zones of increased stress away from the corner into the coal and rock body. Stress at workings with round cross-sections is 3-4 times lower than at square cross-sections. Recommendations are given that concern shearer loader operation (semi-spherical shape of the face), borehole drilling and water injection. Initial distance of 10-15 m between boreholes is suggested. 3 refs.

Automated mineralogical logging of coal and coal measure core

Energy Technology Data Exchange (ETDEWEB)

Stephen Fraser; Joan Esterle; Colin Ward; Ruth Henwood; Peter Mason; Jon Huntington; Phil Connor; Reneta Sliwa; Dave Coward; Lew Whitbourn [CSIRO Exploration & Mining (Australia)

2006-06-15

A mineralogical core logging system based on spectral reflectance (HyLogger{trademark}) has been used to detect and quantify mineralogies in coal and coal measure sediments. The HyLogger{trademark} system, as tested, operates in the visible-to-shortwave infrared spectral region, where iron oxides, sulphates, hydroxyl-bearing and carbonate minerals have characteristic spectral responses. Specialized software assists with mineral identification and data display. Three Phases of activity were undertaken. In Phase I, carbonates (siderite, ankerite, calcite) and clays (halloysite, dickite) were successfully detected and mapped in coal. Repeat measurements taken from one of the cores after three months demonstrated the reproducibility of the spectral approach, with some spectral differences being attributed to variations in moisture content and oxidation. Also, investigated was HyLogger{trademark} ability to create a 'brightness-profile' on coal materials, and these results were encouraging. In Phase II, geotechnically significant smectitic clays (montmorillonite) were detected and mapped in cores of clastic roof and floor materials. Such knowledge would be useful for mine planning and design purposes. In Phase III, our attempts at determining whether phosphorus-bearing minerals such as apatite could be spectrally detected were less than conclusive. A spectral index could only be created for apatite, and the relationships between the spectrally-derived apatite-index, the XRD results and the analytically-derived phosphorus measurements were ambiguous.

Geochemical characteristics of Carboniferous-Permian coal-formed gas in Bohai Bay Basin

Energy Technology Data Exchange (ETDEWEB)

Shipeng Huang; Fengrong Liao; Xiaoqi Wu [PetroChina, Beijing (China). Research Institute of Petroleum Exploration & Development

2010-03-15

Coal-formed gas reservoirs have been found in several depressions in Bohai Bay Basin. The gas was mainly generated by the Carboniferous-Permian coal measures, which are good source rocks. The exploration of coal-formed gas has a broad prospect. The main reservoirs of the coal-formed gas are Ordovician, Carboniferous-Permian, and Paleogene stratum. Coal-formed gas in the Bohai Bay Basin is chiefly composed of hydrocarbon gases. The percentage content of carbon dioxide is more than that of the nitrogen gas. The stable carbon isotope values of the hydrocarbon gases of different depressions and different reservoirs usually reversed. The reversed values of gas samples account for 52.1% of all the samples. Reversion values of the carbon isotope are mainly because of the mixing of gases from same source rocks but with different maturity. Among the three main reservoirs, coal-formed gas preserved in Paleogene stratum has the heaviest carbon isotope, the second is the gas in Carboniferous-Permian stratum, and the Ordovician gas possesses the lightest carbon isotope. Based on the analysis of the characteristics of carbon isotope of hydrocarbon gases in well Qishen-1 and the distribution of the Carboniferous-Permian coal measures, the gas of the well is derived from the high-matured Carboniferous-Permian coal measures.

Formation and retention of methane in coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Hucka, V.J.; Bodily, D.M.; Huang, H.

1992-05-15

The formation and retention of methane in coalbeds was studied for ten Utah coal samples, one Colorado coal sample and eight coal samples from the Argonne Premium Coal Sample Bank.Methane gas content of the Utah and Colorado coals varied from zero to 9 cm{sup 3}/g. The Utah coals were all high volatile bituminous coals. The Colorado coal was a gassy medium volatile bituminous coal. The Argonne coals cover a range or rank from lignite to low volatile bituminous coal and were used to determine the effect of rank in laboratory studies. The methane content of six selected Utah coal seams and the Colorado coal seam was measured in situ using a special sample collection device and a bubble desorbometer. Coal samples were collected at each measurement site for laboratory analysis. The cleat and joint system was evaluated for the coal and surrounding rocks and geological conditions were noted. Permeability measurements were performed on selected samples and all samples were analyzed for proximate and ultimate analysis, petrographic analysis, {sup 13}C NMR dipolar-dephasing spectroscopy, and density analysis. The observed methane adsorption behavior was correlated with the chemical structure and physical properties of the coals.

Performance of diamond and point attack coal cutter picks

Energy Technology Data Exchange (ETDEWEB)

Liu, Y. [CSIRO, Brisbane, Qld. (Australia). Division of Exploration and Mining

1996-12-31

This paper presents results of laboratory experiments and field trials of PDC (Polycrystalline Diamond Compact) and PA (Point Attack) coal cutter picks. Laboratory cutting tests included linear rock and coal cutting and turning rock cutting. The following parameters were measured to assess performance of PDC and PA cutter picks: cutting force, normal force, specific energy consumption, yield, dust generation and ignitional characteristics (temperature rise). Field trials were conducted on a longwall shearer. Performance of both types of pick interims of pick life and dust generation were assessed. 3 refs., 18 figs., 3 tabs.

Application of Confined Blasting in Water-Filled Deep Holes to Control Strong Rock Pressure in Hard Rock Mines

Directory of Open Access Journals (Sweden)

Jingxuan Yang

2017-11-01

Full Text Available In extra-thick coal seams, mining operations can lead to large-scale disturbances, complex overburden structures, and frequent and strong strata behavior in the stope, which are serious threats to mine safety. This study analyzed the overburden structure and strata behavior and proposed the technique of confined blasting in water-filled deep holes as a measure to prevent strong rock pressure. It found that there are two primary reasons for the high effectiveness of the proposed technique in presplitting hard coal and rock. First, the fracture water enables much more efficient transfer of dynamic load due to its incompressibility. Second, the subsequent expansion of water can further split the rock by compression. A mechanical model was used to reveal how the process of confined blasting in water-filled deep holes presplit roof. Moreover, practical implementation of this technique was found to improve the structure of hard, thick roof and prevent strong rock pressure, demonstrating its effectiveness in roof control.

Shale Failure Mechanics and Intervention Measures in Underground Coal Mines: Results From 50 Years of Ground Control Safety Research

Science.gov (United States)

2015-01-01

Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining. PMID:26549926

煤岩组合体力学特性与瓦斯渗流规律试验研究%Experimental Study on Mechanical Properties and Permeability Evolution Law of Coal-rock Combination

Institute of Scientific and Technical Information of China (English)

常悦; 张雅萍; 栗继祖; 王向玲; 马利云; 李燕

2017-01-01

Based on triaxial permeability test system,the strength characteristics and permeability evolution law of coal-rock specimens of different height ratios of rock to coal under the condition of simulating different thicknesses of roof-coal-floor are studied.The results show that the peak strength values for coal-rock specimens are different due to the different height ratios of rock to coal,and the peak stress increases with the height ratio.The broken and failure models of the coal-rock combination specimens show a macroscopic shear fracture surface,and the fracture surface runs through the top and bottom rocks.With the increase of the axial strain,the permeability evolution law of the coal-rock combination specimen shows the "V" shape,which decreases to the lowest point first and then increases rapidly.And the corresponding axial strain of the permeability curve increases with the increase of the height ratio of rock to coal.%利用三轴渗流测试系统,模拟不同厚度的顶板、煤层和底板条件,进行了不同岩煤高度比条件下煤岩组合试件的力学特性与渗流规律的试验研究.结果表明:对于不同岩煤高度比的煤岩组合试件,失稳破坏的峰值强度存在差异,且峰值强度随岩煤高度比的增加呈增大趋势;组合煤岩体的失稳破坏呈现宏观剪切破裂面,且破裂面贯穿顶、底部岩石;组合煤岩体的渗透率随轴向应变的升高呈现先减小到最小值后迅速增加的“V”型变化趋势;且随着岩煤高度比的增加,渗透率曲线反弹点对应的轴向应变呈增大趋势.

Application of in-situ stress measurement on bursts disasters of rock and CO{sub 2} in coal mine

Energy Technology Data Exchange (ETDEWEB)

Lian-Jie Wang; Dong-Sheng Sun; Li-Rong Zhang; Guan-Wu Zhou [Ministry of Land and Resources, Beijing (China)

2009-01-15

For the purpose of reduction and prevention of rock burst disasters and CO{sub 2}, measurements were made of in-situ stress and mechanical parameters of rock in Yingcheng mine. Geological structure and gas measurements were studied and the stress field was simulated and distribution of stress field was obtained in this area. On the basis of the study, the danger areas of rockbursts and CO{sub 2} were predicted. Preventive measures were suggested to decrease gas pressure and in-situ stress in front of the working face with advance boreholes relieving blasting. 12 refs., 5 figs., 1 tab.

Application of gamma-gamma logging in predicting anomalous geodynamic phenomena in hard coal mines

International Nuclear Information System (INIS)

Blaha, F.; Keclik, L.

1980-01-01

The application is discussed of gamma-gamma logging in the prediction of dynamic events like coal and gas bursts, coal sliding in medium dip seams and rock bumps. The overall analysis of the applied rock characterization method and of the measurement results shows that the prediction possibilities of dynamic events are partly limited due to specific effects of the rock massive. In these cases, however, unambiguous results may be obtained by other geophysical methods such as seismoacoustic testing etc. In most cases, however, the gamma-gamma logging results may be used for estimating the degree of dynamic events or checking the efficiency of preventive measures in the locality under investigation. (author)

Evolution characteristics and application of diamondoids in coal measures

Directory of Open Access Journals (Sweden)

Chenchen Fang

2016-02-01

Full Text Available As diamondoids have been used to evaluate petroleum and source rocks widely; their origin, evolution, and distribution in petroleum as well as source rocks have attracted ever more attention. Having finished the pyrolysis simulation experiment of the coal measure mudrocks from Xujiahe Formation, Sichuan Basin, results indicated that with the equivalent vitrinite reflectance (EasyRo increasing, diamondoids experience generation (1.0%  1.5%. Throughout the simulation experiment, diamondoid parameters MAI, EAI, and TMAI-1 kept good relationships with maturity within the range of EasyRo 1.5%–2.5%, 1.0%–2.5%, and 1.5%–2.5% respectively, with all of the correlation coefficient (R2 being above 0.7844, this indicated that these parameters can be used to evaluate maturity at these ranges. In addition, the yield ratios A/D, MA/MD, DMA/DMD, and As/Ds also kept good relationships with maturity at the range of EasyRo 1.2%–2.5%, with all of the R2 above 0.9236, this indicated that these ratios can be used to evaluate maturity index at this range.

Losses in the coal supply chain

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-12-15

This report examines the way coal can change as it passes along the coal chain. A great deal of the change is intended, through separation and sizing, to ensure the coal being mined matches the specification demanded by the customer. This report attempts to identify these changes and presents some of the issues faced by the coal supplier and user. Much of the change leads to a loss of mass in the coal. Some of the coal is left in the ground (intentionally and unintentionally), while elsewhere, full extraction might occur with the addition of non-coal materials from the surrounding rocks. In both cases, the mined coal often requires further processing. Coal processing by separation at preparation plants refines coal further and is where most of the mass loss occurs. Value is added by reducing ash content and improving heating value, thus providing a much more saleable product for the market. As soon as the coal leaves the mine, mass loss can occur either through natural deterioration of the fuel, through spillage or dust, or in extreme cases theft. In all cases measuring the amount of coal as it passes through the supply chain is required to verify that the coal reaching the consumer is of satisfactory quality and quantity. This can be done crudely by measuring stockpiles, to more sophisticated weighing systems at various points along the supply chain, and even measuring the volume held in a ship. Measurement is subject to error which must be minimised. Biomass needs to be processed in much the same way as coal, such as removing mineral matter and taking care in avoiding contamination.

Similar simulation study on the characteristics of the electric potential response to coal mining

Science.gov (United States)

Niu, Yue; Li, Zhonghui; Kong, Biao; Wang, Enyuan; Lou, Quan; Qiu, Liming; Kong, Xiangguo; Wang, Jiali; Dong, Mingfu; Li, Baolin

2018-02-01

An electric potential (EP) can be generated during the failure process of coal and rock. In this article, a similar physical model of coal rock was built and the characteristics of the EP responding to the process of coal mining were studied. The results showed that, at the early mining stage, the structure of coal rock strata were stable in the simulation model, the support stress of overlying coal rock strata was low and the maximum subsidence was little, while the EP change was less. With the advancement of the working face, the support stress of the overlying coal rock strata in the mined-out area changed dramatically, the maximum subsidence increased constantly, the deformation and destruction were aggravated, and cracks expanded continuously. Meanwhile, the EP response was significant with fluctuation. When significant macro damage appeared in coal rock strata, the EP signal fluctuation was violent. The overlying coal rock strata were influenced by gravity and mining activity. During the mining process, the crack growth and the friction, together with slip between coal and rock particles, resulted in the response of EP. The change in EP was closely related to the damage state and stress distribution of the coal rock strata. EP monitoring has the advantages of accurate reflection and strong anti-interference in the field. Therefore, with further study, an EP monitoring method could be applied for monitoring and early warning of coal and rock dynamic disaster, and risk evaluation in the future. The strength of the EP and its fluctuation degree could serve as the key discrimination indexes.

Forecast and Prevention of Coal and Gas Outbursts in the Case of Application of a New Mining Method - Drilling of a Coal Pillar

Directory of Open Access Journals (Sweden)

Vlastimil Hudeček

2010-10-01

Full Text Available Coal and gas outbursts are one of risk factors accompanying the mining of coal in low seams in the Ostrava-Karviná Coalfield.At the use of the method of longwall mining, all coal reserves have not been mined out owing to tectonic faults. For mining outthe residual reserves, the application of a new mining method - drilling of a coal pillar was proposed.The method of mining of a coal seam utilizing long large diameter boreholes is verified in the Paskov Mine (company OKD, JSC –Czech Republic under conditions of rock mass with hazard of rock and gas outbursts in localities of residual pillars left in seams afterfinishing the mining operations performed with using the classical method of longwall working along the strike. [5]Forecast and preventive measures applied to the verification of the new method were based on previous experience withthe mining of seams with hazard of coal and gas outbursts. They accepted fully valid legislation, i.e. Ordinance of Ostrava RegionalMining Authority No. 3895/2002 and supplementary materials (Instructions and Guidelines. The proposed measures respectedthe character of the method being verified. [4]For all areas being mined, projects containing also chapters specifying the problems of ensuring the safety of mining worksand operation under conditions of hazard of coal and gas outbursts were prepared.In the contributions, basic proposals for the principles of coal and gas outburst forecast and prevention when applying the newmining method – drilling of a coal pillar are presented

Multiparameter Monitoring and Prevention of Fault-Slip Rock Burst

Directory of Open Access Journals (Sweden)

Shan-chao Hu

2017-01-01

Full Text Available Fault-slip rock burst is one type of the tectonic rock burst during mining. A detailed understanding of the precursory information of fault-slip rock burst and implementation of monitoring and early warning systems, as well as pressure relief measures, are essential to safety production in deep mines. This paper first establishes a mechanical model of stick-slip instability in fault-slip rock bursts and then reveals the failure characteristics of the instability. Then, change rule of mining-induced stress and microseismic signals before the occurrence of fault-slip rock burst are proposed, and multiparameter integrated early warning methods including mining-induced stress and energy are established. Finally, pressure relief methods targeting large-diameter boreholes and coal seam infusion are presented in accordance with the occurrence mechanism of fault-slip rock burst. The research results have been successfully applied in working faces 2310 of the Suncun Coal Mine, and the safety of the mine has been enhanced. These research results improve the theory of fault-slip rock burst mechanisms and provide the basis for prediction and forecasting, as well as pressure relief, of fault-slip rock bursts.

Geology and fuel resources of the southern part of the San Juan Basin, New Mexico. Part 1, The coal field from Gallup eastward toward Mount Taylor, with a measured section of pre-Dakota(?) rocks near Navajo Church

Science.gov (United States)

Sears, Julian D.

1934-01-01

member is split by the thick Hosta sandstone member, which toward the east and northeast is in turn split by the Satan tongue of the Mancos shale, of upper Niobrara (upper Colorado) age.In general the structure of the rocks is simple, showing a gentle northward dip into the San Juan Basin. At the west edge of the field the rocks dip steeply west in the north end of the prominent ridges known locally as the Hogback. In the eastern part there is a series of pronounced folds, whose crests and troughs retain the gentle basinward dip but whose limbs are steep monoclines that in places are faulted.The coal is of subbituminous rank and of fairly good grade. The coal beds are very irregular and lenticular. Those in the Gallup and Dilco members are of comparatively little importance, reaching a thickness of 4 to 5 feet in only a few places and, in general, being less than 3 feet thick. The coal beds of the Gibson, especially of its lower part, are more numerous and thicker, measurements of 4 to 6 feet thick being fairly common and one bed showing a thickness of 12 feet for more than a mile. No commercial mining has been undertaken in this field, but a few small mines have been used to supply trading posts and the Indian schools at Crown Point and Tohatchi.

Coal plows in underground mines in Czechoslovakia

Energy Technology Data Exchange (ETDEWEB)

Vasek, J.; Klimek, M.

1980-05-01

This article discusses factors which influence the possibility of using coal plows for mining black coal seams in Czechoslovakia. Seams inclined at angles up to 40 degrees can be mined by plows. Another factor which influences plow work is ease of separating coal seam from the direct roof: the plow can be used in seams with good or average separation, and can not be used in seams with roofs difficult to separate from the seam. Quality of rocks surrounding the coal seam: If the stability of the roof is low and strength of rock is low and roof falls occur easily coal plows can not be used. From among three classes of rock in Czechoslovakia plows can be used only in the class characterized by the highest strength. Intense seam dislocations are one of the most important difficulties in using coal plows. Plows can be used if height of seam dislocations is not greater than 40% of the seam thickness. Further factors which influence the possibility of using coal plows (coal resistance to cutting, features of cutting elements of the plow, specific features of the plow mechanism etc.) are also discussed. A method for assessing advantages and disadvantages of using coal plows in given circumstances is presented. (10 refs.) (In Czech)

Determining air distribution during outbursts of gases and rocks

Energy Technology Data Exchange (ETDEWEB)

Struminski, A; Sikora, M; Urbanski, J [Politechnika Wroclawska (Poland). Instytut Gornictwa

1989-01-01

Discusses use of the KPW-1 iterative and autocorrelation method developed by A. Struminski for forecasting effects of rock bursts on ventilation systems of underground coal mines with increased content of methane or carbon dioxide in coal seams and adjacent rock strata. The method is used for prediction of air flow changes caused by a rock burst accompanied by violent outburst of gases. Directions of air flow, flow rate and concentration of gases emitted from surrounding strata to mine workings are predicted. On the basis of this prediction concentration of gases from a coal outburst is determined for any point in a ventilation network. The prediction method is used for assessing hazards for coal mines during and after a rock burst. Use of the method is explained on the example of the Thorez and Walbrzych coal mines. Computer programs developed for ODRA and IBM/XT computers are discussed. 6 refs.

Study on Monitoring Rock Burst through Drill Pipe Torque

OpenAIRE

Zhonghua Li; Liyuan Zhu; Wanlei Yin; Yanfang Song

2015-01-01

This paper presents a new method to identify the danger of rock burst from the response of drill pipe torque during drilling process to overcome many defects of the conventional volume of drilled coal rubble method. It is based on the relationship of rock burst with coal stress and coal strength. Through theoretic analysis, the change mechanism of drill pipe torque and the relationship of drill pipe torque with coal stress, coal strength, and drilling speed are investigated. In light of the a...

Micrinite maceral evidence of hydrocarbon generation in cretaceous coal measures of the middle Benue trough, Nigeria

International Nuclear Information System (INIS)

Obaje, N. G.; Ukpabio, E. J.; Funtua, I. I.

1999-01-01

Maceral analysis on samples from the coal and coal-bearing strata of the Awgu Formation in the Middle Benue Trough of Nigeria allows the subdivision of the coal beds and inter seam sediments into three different petrographic/coal facies, namely: a vitrinite-fusinite coal facies which is rich in vitrinite, poor in liptinite, with variable amounts of inertinite and low mineral matter content; a trimaceritic coal facies which is rich in vitrinite, liptinite and inertinite with low mineral matter content; and a shaley coal facies which, expectedly, is dominated by mineral matter and has variable amounts of vitrinite, liptinite and inertinite. Micrinite macerals constitute 8.2% and 4.5 on mineral matter-counted basis in samples from the trimaceritic and shaley coal facies respectively. These amounts, in both cases, are considered to be very high. They occur as finely particulate, rounded grains approximately I um in diameter. Most of the micrinite are closely associated with highly reflecting, almost unrecognizable liptinite. The nature and origin of micrinite and its significance to oil and gas generation have been studied extensively. As secondary macerals, they are generally believed to be relics of oil generation from oil-prone macerals, mainly liptinitic and vitrinitic macerals with which they are closely associated. Reflectance measurements on the associated vitrinite macerals indicate a thermal maturity range of 0.74 - 1.25 % Rm. This range corresponds to the zone of oil generation in most minerogenic oil source rocks. In the study area, however, only the trimaceritic coal facies and some parts of the shaley coal facies that are rich in liptinite alongside the associated micrinite macerals are considered to have generated oil. The vitrinite-fusinite coal facies with its high content of humic organic matter (vitrinite + Inertinite) can only generate gas (wet + dry) within the given thermal maturity range

Chemical analysis of carbonates and carbonate rocks by atomic absorption analysis

Energy Technology Data Exchange (ETDEWEB)

Tardon, S

1981-01-01

Evaluates methods of determining chemical composition of rocks surrounding black coal seams. Carbonate rock samples were collected in the Ostrava-Karvina coal mines. Sampling methods are described. Determination of the following elements and compounds in carbonate rocks is discussed: calcium, magnesium, iron, manganese, barium, silicon, aluminium, titanium, sodium, potassium, sulfur trioxide, phosphorus pentoxide, water and carbon dioxide. Proportion of compounds insoluble in water in the investigated rocks is also determined. Most of the elements are determined by means of atomic absorption analysis. Phosphorus is also determined by atomic absorption analysis. Other compounds are determined gravimetrically. The described procedure permits weight of a rock sample to be reduced to 0.5 g without reducing analysis accuracy. The results of determining carbonate rock components by X-ray analysis and by chemical analysis are compared. Equipment used for atomic absorption analysis is characterized (the 503 Perkin-Elmer and the CF-4 Optica-Milano spectrophotometers). The analyzed method for determining carbonate rock permits more accurate classification of rocks surrounding coal seams and rock impurities in run-of-mine coal. (22 refs.) (In Czech)

Effects of water infusions on mechanical properties of carboniferous rocks

Energy Technology Data Exchange (ETDEWEB)

Vavro, M; Chlebik, J

1977-01-01

Method of water infusion is used in the Ostrava-Karvina coal region in Czechoslovakia, where the roof of the extracted coal seam consists of thick rock layers (sandstone, Namurian B series) characterized by high resistance to compression, high coefficient of linear elasticity and high capacity of accumulating energy. When the resistance boundary is crossed and the rocks are disturbed this energy is suddenly released and transferred to the surrounding rock masses, coal seam and support system. On the basis of laboratory experiments the physico-mechanical and energy properties of carboniferous rocks together with calculation of their energy coefficient and other parameters are described and calculated. The results of research and theoretical solutions are presented. Practical use of water infusions to influence mechanical properties of sandstone in the roof of coal seams is described with the example of the Dukla coal mine. (5 refs.) (In Polish)

Effect of Water on Coal Strength | Singh | Momona Ethiopian Journal ...

African Journals Online (AJOL)

Water content is one of the most important factors influencing the rock strength. The present study has been conducted to see how coal strength changes under dry and water saturated conditions. The study reveals that the strength of coal decreases with increasing moisture. For rock mechanics and rock engineering ...

Methods for the risk assessment of rock bursts under the condition of the Upper Silesian coal basin; Methoden zur Bewertung des Risikos von Gebirgsschlaegen unter Bedingungen des oberschlesischen Kohlebeckens

Energy Technology Data Exchange (ETDEWEB)

Myszkowski, Jacek [Forschungsanstalt fuer Gebirgsschlaege und Gebirgsmechanik BT, Katowice (Poland). Hauptinst. fuer Bergbau

2013-06-15

The assessment of the risk of rock burst in underground coal mines is associated with the forecasting, assessment and management of risks. The contribution under consideration presents methods for the risk assessment and prevention of rock bursts.

Biomarkers, carbon isotopic composition and source rock potentials of Awgu coals, middle Benue trough, Nigeria

Science.gov (United States)

Adedosu, Taofik A.; Sonibare, Oluwadayo O.; Tuo, Jincai; Ekundayo, Olusegun

2012-05-01

Coal and carbonaceous shale samples were collected from two boreholes (BH 94 and BH 120) in Awgu formation of Middle Benue Trough, Nigeria. Source rock potentials of the samples were studied using biomarkers and carbon isotopic composition. Biomarkers in the aliphatic fractions in the samples were studied using Gas Chromatography-Mass Spectrometry (GC-MS). The Carbon isotope analysis of individual n-alkanes in the aliphatic fraction was performed using Gas Chromatography-Combustion-Isotope Ratio Mass Spectrometer (GC-IRMS). The abundance of hopanes, homohopanes (C31-C35), and C29 steranes in the samples indicate terrestrial plant, phytoplankton and cyanobacteria contributions to the organic matter that formed the coal. High (Pr/Ph) ratio (3.04-11.07) and isotopic distribution of individual alkanes showed that the samples consisted of mixed terrestrial/marine organic matter deposited under oxic condition in lacustrine-fluvial/deltaic depositional environment. The maturity parameters derived from biomarker distributions showed that the samples are in the main phase of oil window.

Measurements of thermal properties of rocks

International Nuclear Information System (INIS)

Kumada, Toshiaki

2001-02-01

The report concerns the measurement of thermal conductivity and specific heat of supplied sedimental rock B and Funyu rock. The method of measurement of these properties was done with the method which was developed at 1997 and improved much in its accuracy by the present author et al. The porosity of sedimental rock B is 0.55, which is deduced from the density of rock (the porosity deduced from the difference between dry and water filled conditions is 0.42) and the shape and size of pores in rock are much different. Its thermal conductivity is 0.238 W/mK in dry and 1.152 W/mK in water filled conditions respectively, while the thermal conductivity of bentonite is 0.238 W/mK in dry and 1.152 W/mK in water saturated conditions. The difference of thermal conductivity between dry and water saturated conditions is little difference in sedimental rock B and bentonite at same porosity. The porosity of Funyu rock is 0.26 and the shape and size of pores in the rock are uniform. Its thermal conductivity is 0.914 W/mK in dry and 1.405 W/mK in water saturated conditions, while the thermal conductivity of bentonite is 0.606 W/mK in dry and 1.591 W/mK in water saturated conditions respectively. The correlation estimating thermal conductivity of rocks was derived based on Fricke correlation by presuming rocks as a suspension. (author)

The experimental modeling of gas percolation mechanisms in a coal-measure tight sandstone reservoir: A case study on the coal-measure tight sandstone gas in the Upper Triassic Xujiahe Formation, Sichuan Basin, China

Directory of Open Access Journals (Sweden)

Shizhen Tao

2016-12-01

Full Text Available Tight sandstone gas from coal-measure source rock is widespread in China, and it is represented by the Xujiahe Formation of the Sichuan Basin and the Upper Paleozoic of the Ordos Basin. It is affected by planar evaporative hydrocarbon expulsion of coal-measure source rock and the gentle structural background; hydrodynamics and buoyancy play a limited role in the gas migration-accumulation in tight sandstone. Under the conditions of low permeability and speed, non-Darcy flow is quite apparent, it gives rise to gas-water mixed gas zone. In the gas displacing water experiment, the shape of percolation flow curve is mainly influenced by core permeability. The lower the permeability, the higher the starting pressure gradient as well as the more evident the non-Darcy phenomenon will be. In the gas displacing water experiment of tight sandstone, the maximum gas saturation of the core is generally less than 50% (ranging from 30% to 40% and averaging at 38%; it is similar to the actual gas saturation of the gas zone in the subsurface core. The gas saturation and permeability of the core have a logarithm correlation with a correlation coefficient of 0.8915. In the single-phase flow of tight sandstone gas, low-velocity non-Darcy percolation is apparent; the initial flow velocity (Vd exists due to the slippage effect of gas flow. The shape of percolation flow curve of a single-phase gas is primarily controlled by core permeability and confining pressure; the lower the permeability or the higher the confining pressure, the higher the starting pressure (0.02–0.08 MPa/cm, whereas, the higher the quasi-initial flow speed, the longer the nonlinear section and the more obvious the non-Darcy flow will be. The tight sandstone gas seepage mechanism study shows that the lower the reservoir permeability, the higher the starting pressure and the slower the flow velocity will be, this results in the low efficiency of natural gas migration and accumulation as well as

Dynamic measurement of coal thermal properties and elemental composition of volatile matter during coal pyrolysis

Directory of Open Access Journals (Sweden)

Rohan Stanger

2014-01-01

Full Text Available A new technique that allows dynamic measurement of thermal properties, expansion and the elemental chemistry of the volatile matter being evolved as coal is pyrolysed is described. The thermal and other properties are measured dynamically as a function of temperature of the coal without the need for equilibration at temperature. In particular, the technique allows for continuous elemental characterisation of tars as they are evolved during pyrolysis and afterwards as a function of boiling point. The technique is demonstrated by measuring the properties of maceral concentrates from a coal. The variation in heats of reaction, thermal conductivity and expansion as a function of maceral composition is described. Combined with the elemental analysis, the results aid in the interpretation of the chemical processes contributing to the physical and thermal behaviour of the coal during pyrolysis. Potential applications in cokemaking studies are discussed.

Primary Rock Temperature Fields in Czech and Polish Part of the Upper of the Upper Silesian Coal Basin / Pole temperatury pierwotnej skał w czeskiej i polskiej części górnośląskiego okręgu węglowego

Science.gov (United States)

Doležal, Libor; Knechtel, Józef; Taufer, Antonín; Trávníček, Ludvík

2013-03-01

Knowledge of the temperature of rock mass is no doubt of substantial meaning, both for the solution of economicaly demanding protection of mine workers in difficult microclimatic environment and for perspective usage of geothermal energy from the depth of the earth. International cooperation of our and Polish specialists is in this sense more than welcome, also because the exploitation of coal seams takes place in the same Upper Silesia rock coal basin. This profesional article is concentrated on complex analysis of temperature fields of the Ostrava- Karviná district, mainly from results of thermologging measurements in geological survey boreholes both on surface and underground, and also from the actual temperature measurements in the coal mines. One chapter of this article describes the original approach to the survey of temperature field and its prognosis in the Polish part of the Upper Silesia coal basin by a researcher from GIG Katowice. The most suitable method of analysis of primary temperature field seemed the preparation of isocurves of temperature(isothermal lines) for the existing mine working areas, even if the method of obtaining them was different. The Czech method is based on determination of the quantitative dependence of temperature on the rock mass depth from the abovementioned measurement results, calculation of geothermal gradients and the following recalculation of real temperature values for various depth levels. Then isothermal lines for these depth levels are created together with colour distingushing of their value limits. The Polish method is sufficiently described in a dedicated chapter. The conclusion of the article underlines the decisive role of the structuraly tectonic composition of the rock mass on the temperature field in the long term thermic evolution of the Earth.

Laboratory measurements of rock thermal properties

DEFF Research Database (Denmark)

Bording, Thue Sylvester; Balling, N.; Nielsen, S.B.

The thermal properties of rocks are key elements in understanding and modelling the temperature field of the subsurface. Thermal conductivity and thermal diffusivity can be measured in the laboratory if rock samples can be provided. We have introduced improvements to the divided bar and needle...... probe methods to be able to measure both thermal conductivity and thermal diffusivity. The improvements we implement include, for both methods, a combination of fast numerical finite element forward modelling and a Markov Chain Monte Carlo inversion scheme for estimating rock thermal parameters...

Study on coal dust wettability measurement using cold briquetting technique

Energy Technology Data Exchange (ETDEWEB)

Li, M.; Xu, H.; Shu, X. [North China Institute of Science and Technology, Beijing (China). Department of Resource and Environmental Engineering

2008-12-15

Quantitative measuring of coal dust wettability is essential for the research and development of chemical coal dust suppressants in the field of dust control with wetting-agent-added water. The causes of low repeat rate and poor consistency in present lab testing of coal dust wettability are discussed. The influence of different briquetting pressure (from 0 to 6.5108 Pa) on the wet behavior of coal dust is investigated as a new way to quantitatively evaluate coal dust wettability. The study shows that there is a fairly high coincidence between the coal dust wettability data measured by the briquetting technique and the results gained from the lab dust suppression tests using an MCYZ apparatus designed by the authors. 9 refs., 8 figs., 2 tabs.

Coal waste management practices in the USA:an overview

Institute of Scientific and Technical Information of China (English)

Yoginder P. Chugh; Paul T. Behum

2014-01-01

This paper provides an overview of coal waste management practices with two case studies and an estimate of management cost in 2010 US dollars. Processing of as-mined coal typically results in considerable amount of coarse and fine coal processing wastes because of in-seam and out-of-seam dilution mining. Processing plant clean coal recovery values run typically 50%–80%. Trace metals and sulfur may be present in waste materials that may result in leachate water with corrosive charac-teristics. Water discharges may require special measures such as liner and collection systems, and treatment to neutralize acid drainage and/or water quality for trace elements. The potential for variations in coal waste production and quality depends upon mining or processing, plus the long-term methods of waste placement. The changes in waste generation rates and engineering properties of the coal waste during the life of the facility must be considered. Safe, economical and environmentally acceptable management of coal waste involves consideration of geology, soil and rock mechanics, hydrology, hydraulics, geochemistry, soil science, agronomy and environmental sciences. These support all aspects of the regulatory environment including the design and construction of earth and rock embankments and dams, as well as a wide variety of waste disposal structures. Development of impoundments is critical and require considerations of typical water-impounding dams and additional requirements of coal waste disposal impoundments. The primary purpose of a coal waste disposal facility is to dispose of unusable waste materials from mining. However, at some sites coal waste impoundments serve to provide water storage capacity for processing and flood attenuation.

Effects of torpedo blasting on rockburst prevention during deep coal seam mining in the Upper Silesian Coal Basin

Directory of Open Access Journals (Sweden)

Ł. Wojtecki

2017-08-01

Full Text Available In the Upper Silesian Coal Basin (USCB, coal seams are exploited under progressively more difficult geological and mining conditions (greater depth, higher horizontal stress, more frequent occurrence of competent rock layers, etc.. Mining depth, dislocations and mining remnants in coal seams are the most important factors responsible for the occurrence of rockburst hazards. Longwall mining next to the mining edges of neighbouring coal seams is particularly disadvantageous. The levels of rockburst hazards are minimised via the use of rockburst prevention methods. One active prevention method is torpedo blasting in roof rocks. Torpedo blastings are performed in order to decrease local stress concentrations in rock masses and to fracture the roof rocks to prevent or minimise the impact of high-energy tremors on excavations. The estimation of the effectiveness of torpedo blasting is particularly important when mining is under difficult geological and mining conditions. Torpedo blasting is the main form of active rockburst prevention in the assigned colliery in the Polish part of the USCB. The effectiveness of blasting can be estimated using the seismic effect method, in which the seismic monitoring data and the mass of explosives are taken into consideration. The seismic effect method was developed in the Czech Republic and is always being used in collieries in the Czech part of the coal basin. Now, this method has been widely adopted for our selected colliery in the Polish part of the coal basin. The effectiveness of torpedo blastings in the faces and galleries of the assigned longwall in coal seam 506 has been estimated. The results show that the effectiveness of torpedo blastings for this longwall was significant in light of the seismic effect method, which corresponds to the in situ observations. The seismic effect method is regularly applied to estimating the blasting effectiveness in the selected colliery.

Mercury distribution in coals influenced by magmatic intrusions, and surface waters from the Huaibei Coal Mining District, Anhui, China

International Nuclear Information System (INIS)

Yan, Zhicao; Liu, Guijian; Sun, Ruoyu; Wu, Dun; Wu, Bin; Zhou, Chuncai

2013-01-01

Highlights: • Hg concentrations in coal and surface water samples were determined. • Hg is enriched in the Huaibei coals. • Magmatic activities imparted influences on Hg content and distribution. • Hg contents in surface waters are relative low at the present status. - Abstract: The Hg concentrations in 108 samples, comprising 81 coal samples, 1 igneous rock, 2 parting rock samples and 24 water samples from the Huaibei Coal Mining District, China, were determined by cold-vapor atomic fluorescence spectrometry. The abundance and distribution of Hg in different coal mines and coal seams were studied. The weighted average Hg concentration for all coal samples in the Huaibei Coalfield is 0.42 mg/kg, which is about twice that of average Chinese coals. From southwestern to northeastern coalfield, Hg concentration shows a decreasing trend, which is presumably related to magmatic activity and fault structures. The relatively high Hg levels are observed in coal seams Nos. 6, 7 and 10 in the southwestern coal mines. Correlation analysis indicates that Hg in the southwestern and southernmost coals with high Hg concentrations is associated with pyrite. The Hg concentrations in surface waters in the Huaibei Coal Mining District range from 10 to 60 ng/L, and display a decreasing trend with distance from a coal waste pile but are lower than the regulated levels for Hg in drinking water

A Coal Burst Mitigation Strategy for Tailgate during Deep Mining of Inclined Longwall Top Coal Caving Panels at Huafeng Coal Mine

Directory of Open Access Journals (Sweden)

Guorui Feng

2018-01-01

Full Text Available A coal burst mitigation strategy for tailgate in mining of deep inclined longwall panels with top coal caving at Huafeng Coal Mine is presented in this paper. Field data showed that coal bursts, rib sloughing or slabbing, large convergence, and so forth frequently occurred within the tailgate entries during development and panel retreating employing standard longwall top coal caving (LTCC layout which resulted in fatal injuries and tremendous profit loss. The contributing factors leading to coal bursts were analyzed. Laboratory tests, in situ measurement, and field observation demonstrate that the intrinsic bursting proneness of the coal seam and immediate roof stratum, deep cover, overlying ultrathick (500–800 m conglomerate strata, faults, and, most importantly, improper panel layout led to coal bursts. By employing a new strategy, that is, longwall mining with split-level gateroads (LMSG, gateroads on either end of a LMSG panel are located at different levels within a coal seam, adjacent LMSG panels overlap end to end, and the tailgate of the adjacent new LMSG panel can be located below the headgate entry of the previous LMSG panel or may be offset horizontally with respect to it. Numerical modeling was carried out to investigate the stress distribution and yield zone development within surrounding rock mass which was validated by field investigation. The results indicate that standard LTCC system gave rise to high ground pressure around tailgate entries next to the gob, while LMSG tailgate entry below the gob edge was in a destressed environment. Therefore, coal bursts are significantly mitigated. Field practice of LMSG at Huafeng Coal Mine demonstrates how the new strategy effectively dealt with coal burst problems in mining of deep inclined longwall panels with a reduced incidence of ground control problems. The new strategy can potentially be applied in similar settings.

Source rock hydrocarbons. Present status

International Nuclear Information System (INIS)

Vially, R.; Maisonnier, G.; Rouaud, T.

2013-01-01

This report first presents the characteristics of conventional oil and gas system, and the classification of liquid and gaseous non conventional hydrocarbons, with the peculiar case of coal-bed methane. The authors then describe how source rock hydrocarbons are produced: production of shale oils and gases (horizontal drilling, hydraulic fracturing, exploitation) and of coal-bed methane and coal mine methane. In the next part, they address and discuss the environmental impact of source rock hydrocarbon production: installation footprint, water resource management, drilling fluids, fracturing fluids composition, toxicity and recycling, air pollution, induced seismicity, pollutions from other exploitation and production activities. They propose an overview of the exploitation and production of source rock gas, coal-bed gas and other non conventional gases in the world. They describe the current development and discuss their economic impacts: world oil context and trends in the USA, in Canada and other countries, impacts on the North American market, on the world oil industry, on refining industries, on the world oil balance. They analyse the economic impacts of non conventional gases: development potential, stakes for the world gas trade, consequence for gas prices, development opportunities for oil companies and for the transport sector, impact on CO 2 emissions, macro-economic impact in the case of the USA

Specific Energy of Hard Coal Under Load

Directory of Open Access Journals (Sweden)

Bogusz Anna

2015-03-01

Full Text Available The article presents results of experimental tests of energy parameters of hard coals under loading, collected from research sites located within five main geologic structures of Upper Silesian Coal Basin (GZW - Main Trough, Main Anticline, Bytom Trough, Rybnik Trough and Chwałowice Trough. Coals from12 mines were analysed, starting with seams of group 200, through groups 400, 500, 600 and, finally, seams of group 700. Coal of each of the groups of seams underwent uniaxial compression stress of the energy parameters, in a servo-controlled testing machine MTS-810NEW, for the full range of strain of the tested coal samples. Based on the tests the dependence of different types of specific energy of longitudinal strain of coals on the value of uniaxial compression strength was determined. The dependence of the value of dissipated energy and kinetic energy of coals on the uniaxial compression strength was described with a linear function, both for coals which due to their age belong to various bed sand for various lithotypes of coal. An increase in the value of dissipated energy and in kinetic energy was observed, which was correlated with an increase in uniaxial compression strength of coal. The share of dissipated energy is dominant in the total energy of strain. Share of recoverable energy in the total energy of strain is small, independent of the compression strength of coals and is at most a few per cent high. In coals of low strength and dominant share of dissipated energy, share of recoverable energy is the biggest among the tested coals. It was shown that following an increase in compression strength the share of recoverable energy decreases, while the share of dissipated energy in the total energy increases. Further studies of specific energy of longitudinal strain of rocks in the full-range strain will be the next step inperfecting methodology of research into natural rock burst susceptibility of Carboniferous rock mass and changes in the

Behaviors of overlying strata in extra-thick coal seams using top-coal caving method

Directory of Open Access Journals (Sweden)

Bin Yu

2016-04-01

Full Text Available Accidents such as support failure and excessive deformation of roadways due to drastic changes in strata behaviors are frequently reported when mining the extra-thick coal seams Nos. 3–5 in Datong coal mine with top-coal caving method, which significantly hampers the mine's normal production. To understand the mechanism of strata failure, this paper presented a structure evolution model with respect to strata behaviors. Then the behaviors of strata overlying the extra-thick coal seams were studied with the combined method of theoretical analysis, physical simulation, and field measurement. The results show that the key strata, which are usually thick-hard strata, play an important role in overlying movement and may influence the mining-induced strata behaviors in the working face using top-coal caving method. The structural model of far-field key strata presents a “masonry beam” type structure when “horizontal O-X” breakage type happens. The rotational motion of the block imposed radial compressive stress on the surrounding rock mass of the roadway. This can induce excessive deformation of roadway near the goaf. Besides, this paper proposed a pre-control technology for the hard roof based on fracture holes and underground roof pre-splitting. It could effectively reduce stress concentration and release the accumulated energy of the strata, when mining underground coal resources with top-coal caving method.

Measurement of diffusive properties of intact rock

Energy Technology Data Exchange (ETDEWEB)

Harvey, K B

1996-12-01

In the Postclosure Assessment of a Reference System for the Disposal of Canada`s Nuclear Fuel Waste (Goodwin et al. 1994) the disposal vault is assumed to be surrounded by a zone of intact rock, referred to as the `exclusion zone.` A sensitivity analysis of the relative effectiveness of the several engineered and natural barriers that contribute to the safety of the reference disposal system has shown that this zone of intact rock is the most effective of these barriers to the movement of radionuclides through the reference system. Peer review of the geosphere model used in the case study for the EIS (Environmental Impact Statement) of the Canadian Nuclear Fuel Waste Management Program has identified the need to quantify the properties of the intact rock surrounding the disposal vault that would control the transport of radionuclides by diffusion. The Postclosure Assessment also identified the need for appropriate values of the free water diffusion coefficient (D{sub o}) for {sup 129}1 and {sup 14}C. The measurement of rock resistivity allows the calculation of the Formation Factor for a rock This review describes the Formation Factor, diffusivity, permeability, and porosity, and how these properties might be measured or inferred for insitu rock under the conditions that apply to the intact rock surrounding a potential disposal vault. The importance of measuring the intrinsic diffusion coefficient (D{sup i}) of diffusing species under solution salinities simulating those of groundwaters is emphasised, and a method of measurement is described that is independent of the diffusing medium, and which would be appropriate for measurements made in chemically complex media such as groundwaters. (author). 95 refs., 4 tabs., 39 figs.

Measurement of diffusive properties of intact rock

International Nuclear Information System (INIS)

Harvey, K.B.

1996-12-01

In the Postclosure Assessment of a Reference System for the Disposal of Canada's Nuclear Fuel Waste (Goodwin et al. 1994) the disposal vault is assumed to be surrounded by a zone of intact rock, referred to as the 'exclusion zone.' A sensitivity analysis of the relative effectiveness of the several engineered and natural barriers that contribute to the safety of the reference disposal system has shown that this zone of intact rock is the most effective of these barriers to the movement of radionuclides through the reference system. Peer review of the geosphere model used in the case study for the EIS (Environmental Impact Statement) of the Canadian Nuclear Fuel Waste Management Program has identified the need to quantify the properties of the intact rock surrounding the disposal vault that would control the transport of radionuclides by diffusion. The Postclosure Assessment also identified the need for appropriate values of the free water diffusion coefficient (D o ) for 129 1 and 14 C. The measurement of rock resistivity allows the calculation of the Formation Factor for a rock This review describes the Formation Factor, diffusivity, permeability, and porosity, and how these properties might be measured or inferred for insitu rock under the conditions that apply to the intact rock surrounding a potential disposal vault. The importance of measuring the intrinsic diffusion coefficient (D i ) of diffusing species under solution salinities simulating those of groundwaters is emphasised, and a method of measurement is described that is independent of the diffusing medium, and which would be appropriate for measurements made in chemically complex media such as groundwaters. (author). 95 refs., 4 tabs., 39 figs

Experimental research on the electromagnetic radiation (EMR) characteristics of cracked rock.

Science.gov (United States)

Song, Xiaoyan; Li, Xuelong; Li, Zhonghui; Cheng, Fuqi; Zhang, Zhibo; Niu, Yue

2018-03-01

Coal rock would emit the electromagnetic radiation (EMR) while deformation and fracture, and there exists structural body in the coal rock because of mining and geological structure. In this paper, we conducted an experimental test the EMR characteristics of cracked rock under loading. Results show that crack appears firstly in the prefabricated crack tip then grows stably parallel to the maximum principal stress, and the coal rock buckling failure is caused by the wing crack tension. Besides, the compressive strength significantly decreases because of the precrack, and the compressive strength increases with the crack angle. Intact rock EMR increases with the loading, and the cracked rock EMR shows stage and fluctuant characteristics. The bigger the angle, the more obvious the stage and fluctuant characteristics, that is EMR becomes richer. While the cracked angle is little, EMR is mainly caused by the electric charge rapid separates because of friction sliding. While the cracked angle is big, there is another significant contribution to EMR, which is caused by the electric dipole transient of crack expansion. Through this, we can know more clear about the crack extends route and the corresponding influence on the EMR characteristic and mechanism, which has important theoretical and practical significance to monitor the coal rock dynamical disasters.

Coal graders in Czechoslovakian mines

Energy Technology Data Exchange (ETDEWEB)

Vasek, J.; Klimek, M.

1980-01-01

Problems related to sections of the area of application of graders depending on different mining and geological mining-engineering factors are examined. The principal factors are selected from a general group of influencing factors: dip angle of a formation, separability (shear ability) of coal, characteristics of country rocks, adhesion of coal to rock, tectonic fracturing of a seam, and thickness of a formation. Based on practical and theoretical studies all of the principal factors have been categorized. This allows one to obtain an objective picture of the possibility of using graders under specific conditions by comparing different factors.

Rock stress measurements in the Grimsel Underground Rock Laboratory and their geological interpretation

International Nuclear Information System (INIS)

Braeuer, V.; Heusermann, S.; Pahl, A.

1989-01-01

Rock stress is being studied as part of the Swiss-German cooperation between the National Cooperative for the Storage of Radioactive Waste (NAGRA), the Research Centre for Environmental Sciences (GSF), and the Federal Institute for Geosciences and Natural Resources (BGR) in the Grimsel Rock Laboratory in Switzerland. Several methods and various equipment for measuring rock stress have been developed and tested in an approximately 200-m borehole drilled from a gallery at a depth of 450 m. The measurements were made continually during overcoring; the data were recorded and processed in a computer located downhole or outside the borehole. The results of the overcoring tests and of frac tests indicate a principle horizontal stress of 25-40 MPa, directed mainly NW-SE. Detailed geological mapping shows relationships between stress and rock structure. A zone of nearly unfractured rock exhibits an increase in stress and a change in stress direction. (orig.)

Coal thickness gauge using RRAS techniques, part 1. [radiofrequency resonance absorption

Science.gov (United States)

Rollwitz, W. L.; King, J. D.

1978-01-01

A noncontacting sensor having a measurement range of 0 to 6 in or more, and with an accuracy of 0.5 in or better is needed to control the machinery used in modern coal mining so that the thickness of the coal layer remaining over the rock is maintained within selected bounds. The feasibility of using the radiofrequency resonance absorption (RRAS) techniques of electron magnetic resonance (EMR) and nuclear magnetic resonance (NMR) as the basis of a coal thickness gauge is discussed. The EMR technique was found, by analysis and experiments, to be well suited for this application.

Automatic crack detection method for loaded coal in vibration failure process.

Directory of Open Access Journals (Sweden)

Chengwu Li

Full Text Available In the coal mining process, the destabilization of loaded coal mass is a prerequisite for coal and rock dynamic disaster, and surface cracks of the coal and rock mass are important indicators, reflecting the current state of the coal body. The detection of surface cracks in the coal body plays an important role in coal mine safety monitoring. In this paper, a method for detecting the surface cracks of loaded coal by a vibration failure process is proposed based on the characteristics of the surface cracks of coal and support vector machine (SVM. A large number of cracked images are obtained by establishing a vibration-induced failure test system and industrial camera. Histogram equalization and a hysteresis threshold algorithm were used to reduce the noise and emphasize the crack; then, 600 images and regions, including cracks and non-cracks, were manually labelled. In the crack feature extraction stage, eight features of the cracks are extracted to distinguish cracks from other objects. Finally, a crack identification model with an accuracy over 95% was trained by inputting the labelled sample images into the SVM classifier. The experimental results show that the proposed algorithm has a higher accuracy than the conventional algorithm and can effectively identify cracks on the surface of the coal and rock mass automatically.

Measurement of reflectance of coal macerals: its automation and significance

Energy Technology Data Exchange (ETDEWEB)

Davis, A.

1978-06-01

A prime objective of the Pennsylvania State University's DOE program is the characterization of 1,300 samples of U.S. coals. Reflectance determination plays a major role in meeting this objective, because it is used as an accurate rank index both to select coals for testing and to investigate property-behavior interrelationships using the Penn State/DOE Coal Data Base. Reflectances of coal macerals are related to their refractive and absorptive indices by the Beer equation; the refractive index of the medium and the wavelength of light need to be specified. Determinations usually are made in immersion oil at 546 nm. Properties of vitrinite make it the most suitable maceral for these measurements, but the variety of vitrinite selected may depend upon the intended application. Vitrinite reflectance is considered to be dependent upon the degree of aromatization of its structural units. Although some of the earlier investigators believed that the reflectance of coals increased in a discontinuous, stepped manner as their rank increased, the bulk of assembled data suggests that the change is continuous. Some recent results indicate that there may be more than one coalification track for coals with different geological histories, resulting in displacement from the general trend. Several techniques have been employed to determine the optical properties of coal constituents. Usual comparative method involves the use of a microscope photometer to compare the intensity of light reflected by particles within a polished pellet of coal to that of a glass or synthetic mineral standard. Because coal is anisotropic it is common to measure either maximum reflectance in polarized light or random reflectance in non-polarized light. Various eqipment modifications and accessories have been used to improve the ease of measuring maximum reflectance.

75 FR 81165 - Examinations of Work Areas in Underground Coal Mines for Violations of Mandatory Health or Safety...

Science.gov (United States)

2010-12-27

..., face or ribs and coal or rock bursts. Sec. 75.220(a)(1). Each mine operator shall develop and follow a... materials, ventilation and roof control plans, and maintenance of incombustible content of rock dust are the... the mine * * *. Sec. 75.400. Coal dust, including float coal dust deposited on rock-dusted surfaces...

Gondwana basins and their coal resources in Bangladesh

International Nuclear Information System (INIS)

Nehaluddin, M.; Sultan-ul-Islam, M.

1994-01-01

Fault bounded five Gondwana basins have been discovered in the north western Bangladesh. Among these basins show considerable amount of coal deposits. The Gondwana rocks are highly formed during the Permo-carboniferous diastrophism and later on acquired dynamic characters. In almost all basins, the Permian rocks overlie the Precambrian basement and underlie either the Tertiary or the Cretaceous sediments, structural, stratigraphic, and depositional history of these basins is more or less similar. The sedimentary sequences are composed of light to dark gray, fine to very coarse grained, sub angular to sub rounded felspathic sandstone, dark grey carbonaceous shale and sandstone, variegated conglomerate and thick coal seams (single seam max. 42.38m). The rocks are often alternated and bear the characteristics of cyclic sedimentation. The depositional environments varied from restricted drainage to open fluvial dominated low to moderate sinuous drainage system. The coal bearing basins were flanked by vegetated and swampy over bank. Age of these coals is suggested to be the late permian. Proved and probable reserves of coal in Jamalganj-Paharpur basin are 670 and 1,460 million metric tons, in Barapukuria basin 303 and 3899 million metric tons; in Barapukuria basin 303 and 389 million metric tons; and in Khalaspir basin 143 and 685 million metric tons respectively. The coal is high volatile, low sulphur, bituminous type. It can be used for different forms of thermal conversion. (author)

Selected problems of coal mining mechanization in the coal industry of Poland

Energy Technology Data Exchange (ETDEWEB)

Antoniak, J; Sikora, W [Politechnika Slaska, Gliwice (Poland)

1987-01-01

Discusses conditions for underground coal mining in Poland, types of equipment for coal cutting, mine haulage and strata control and development trends of mining technologies. In 1985, black coal output was 191.6 Mt; 85.3% came from longwall faces mined by sets of mining equipment (coal cutters, chain conveyors and powered supports). The average coal output per longwall face was 881 t/d, output per face mined by sets for mining equipment was 1,134 t/d. In 1985, 653 shearer loaders and 77 coal plows were used in Polish coal mines. Number of shearer loaders is increasing. Shearer loaders with chainless haulage system were safest and most economic. The shearer loaders were equipped with the POLTRAK chainless haulage system developed in Poland. Research programs concentrate on development of new mining equipment for thin seam mining, steep seam mining, longwall mining with hydraulic stowing, efficient strata control by powered or shield supports under conditions of increased stresses or rock burst hazards. 4 refs.

Assessing dynamics of ash content formation in coal at a working face in mines

Energy Technology Data Exchange (ETDEWEB)

Maidukov, G L; Lobkin, V M

1983-05-01

Factors which influence ash content in coal mined at a working face are analyzed: ash content in coal, stability of rock layers surrounding a coal seam, mechanical and physical properties of the direct roof. A mathematical model of ash content formation at a working face is described. On the basis of the model a computer program has been constructed. The program is used for calculating the mean value of ash content in coal and the standardized deviation. The program considers all causes of ash fluctuation in coal such as mining conditions, coal seam thickness, fluctuations in coal seam thickness, mechanical and physical properties of rocks surrounding a coal seam, particularly in the direct roof, mining systems, narrow or wide web shearer loaders, powered supports, hydraulic props, timber friction props with timber roof bars or with steel roof bars. A classification of rocks considering roof stability used by the program is described. A scheme of the program is given. Examples of using the program for forecasting ash content in coal and ash content fluctuations in Donbass mines are evaluated. (In Russian)

Study of Coal Burst Source Locations in the Velenje Colliery

Directory of Open Access Journals (Sweden)

Goran Vižintin

2016-06-01

Full Text Available The Velenje coal mine (VCM is situated on the largest Slovenian coal deposit and in one of the thickest layers of coal known in the world. The thickness of the coal layer causes problems for the efficiency of extraction, since the majority of mining operations is within the coal layer. The selected longwall coal mining method with specific geometry, increasing depth of excavations, changes in stress state and naturally given geomechanical properties of rocks induce seismic events. Induced seismic events can be caused by caving processes, blasting or bursts of coal or the surrounding rock. For 2.5D visualization, data of excavations, ash content and calorific value of coal samples, hanging wall and footwall occurrence, subsidence of the surface and coal burst source locations were collected. Data and interpolation methods available in software package Surfer®12 were statistically analyzed and a Kriging (KRG interpolation method was chosen. As a result 2.5D visualizations of coal bursts source locations with geomechanical properties of coal samples taken at different depth in the coal seam in the VCM were made with data-visualization packages Surfer®12 and Voxler®3.

东滩煤矿煤层底板岩层阻水能力试验研究%Experiment of reduction infiltration ability of rock formation under the coal seam floor at Dongtan Coal Mine

Institute of Scientific and Technical Information of China (English)

张维建; 张新武; 张冬

2015-01-01

底板岩层压水试验能够获得可靠的底板岩层阻水能力实测数据, 为深部煤层开采底板岩层阻水能力提供量化依据,对东滩煤矿深部煤层底板岩层进行压水测试,获得了大量的实测数据并依此计算出岩层的渗透系数. 试验结果表明测试底板岩层段在原始状态下的渗透性很低,阻水能力较强.研究结果可为矿区深部工作面的安全开采提供重要的参考依据.%The reliable reduction infiltration characteristics of rock mass could be obtained by the water injection experiment under the coal seem floor. The data of water injection experimnt were obtained and permeability coefficient of floor formation were deduced through water in-jection experiment at Dongtan Coal Mine. Result shows that the test rock formations are all low-permeability, which mean they have high re-duction infiltration ability. The results make a important reference for safety-mining of deep coal seam working face.

Got Coal? Teaching about the Most Dangerous Rock in America

Science.gov (United States)

Bigelow, Bill

2011-01-01

In 30 years of teaching, the author never taught explicitly about coal. Coal appeared in his social studies curriculum solely as a labor issue, and coal was mostly invisible in his history classes. The world cannot afford this kind of curricular invisibility today. Forty percent of the main greenhouse gas produced in the United States, carbon…

Geothermal, Geochemical and Geomagnetic Mapping Of the Burning Coal Seam in Fire- Zone 18 of the Coal Mining Area Wuda, Inner Mongolia, PR China.

Science.gov (United States)

Kessels, W.; Han, J.; Halisch, M.; Lindner, H.; Rueter, H.; Wuttke, M. W.

2008-12-01

Spontaneous combustion of coal has become a world wide problem caused by and affecting technical operations in coal mining areas. The localization of the burning centre is a prerequisite for any planning of fire fighting operations. In the German - Chinese coal fire project sponsored by the German Ministry of Science and Technologies (Grant No. 0330490K) the so called fire zone 18 of the coal mining area of Wuda (InnerMongolia, PR China) serves as a test area for geophysical measurements. For the geothermal and geochemical mapping 25 up to 1m deep boreholes with a diameter of approx. 30 mm are distributed over the particular fire-zone with an extension of 320 × 180 m2. To avoid the highly dynamic gas flow processes in fire induced fractures caused by weather conditions, all boreholes were situated in the undisturbed rock compartments. In these boreholes, plastic tubes of 12 mm diameter provide access to the borehole ground filled with highly permeable gravel. The boreholes are otherwise sealed to the atmosphere by clay. The geothermal observations consist of measurements of temperature profiles in the boreholes and thermal conductivity measurement on rock samples in the lab. For depths greater then 0.2 m diurnal variations in the temperature gradient were neglected. The derived heat flow with maximum values of 80 W/m2 is more then three orders of magnitude higher than the natural undisturbed heat flow. The high heat flow suggests that the dominant heat transport is gas convection through the system of porous rock and fractures. Any temperature anomaly caused by the burning coal in a depth of more than 18 m would need years to reach the surface by a heat transport restricted to conduction. The geochemical soil gas probing is performed by gas extraction from the boreholes. Measured are the concentrations of O2, CO, CO2, H2S and CH4. The O2 deficit in the soil air and the concentrations of the other combustion products compared to the concentrations in the free

Analytical Technique of Gravel Propensity in Coal pit

OpenAIRE

Kovačič, Blaž; Zupančič, Borislav; Potočnik, Damir

2011-01-01

In terms of surrounding rock with rock burst tendency in coal mine, the rock burst occur when elastic energy accumulation of rock mass system for rock mass deformation reached the limit of rock mass energy storage, and the condition that the factors effected elastic energy accumulation needed to meet can be laid out. The rock burst tendency analysis can be defined as a progress as following: making sure the stress condition of surrounding rock and the. For the purpose of forecasting rock burs...

Comparative organic petrology of interlayered sandstones, siltstones, mudstones and coals in the Upper Carboniferous Ruhr basin, northwest Germany, and their thermal history and methane generation

Energy Technology Data Exchange (ETDEWEB)

Scheidt, G.; Littke, R. (Harress Geotechnik GmbH, Floersheim (Germany, F.R.))

1989-01-01

In the coal-mining Ruhr-area, Upper Carboniferous rocks consist of interlayered sandstones, siltstones, mudstones and coals. They were deposited in a tropical, paralic environment where alternating fluvial sedimentation, occasional marine ingressions, and swamp growth resulted in an irregular cyclic succession. The total sedimentary package contains on an average 6 Vol.% of organic manner. About 70 Vol. % of the organic matter occurs in coal seams, the rest as dispersed organic matter in clastic rocks. The organic matter is autochthonous in the coals and allochthonous in associated sandstones and siltstones. It consists of about 70% vitrinite, 20% inertinite, and 10% liptinite. The overall maceral group composition is the same for coals and dispersed organic matter. This surprising similarity is caused by a nearly exclusive input of land-plant derived organic matter to swamps and fluvial systems and a similar degree of preservation. Highest average liptinite contents were found in unrooted mudstones, highest average inertinite contents in coarse-grained siltstones and highest average vitrinite percentages in sandstones. Maturities of the sediments studied are well within the hydrocarbon generation window, e.g. vitrinite reflectivities range from 0.6% to 1.6%. Reflectivities measured on dispersed particles in clastic rocks are similar to those measured in coal seams. Calculations of the amount of methane generated indicate that coal seams contributed more to the total hydrocarbon generation than dispersed organic matter. 51 refs., 13 figs.

Dating of authigenic clays related to igneous intrusions in Hunter Valley Coals

International Nuclear Information System (INIS)

Zwingmann, H.

2000-01-01

The Sydney Basin is composed mainly of Permian and Triassic marine and non-marine clastic sedimentary strata together with economically significant coal deposits and volumetrically minor igneous rocks. Many of these igneous rocks are also economically significant not only for their use in the construction industry but also for their deleterious effects on coal mining, particularly in underground mines utilising longwall extraction systems. Igneous activity in the Sydney Basin ranges from Early Permian to Tertiary in age and although episodic in nature, activity was unlikely to have ceased for periods of more than approximately 10 million years (Carr and Facer 1980; Embleton et al. 1982). Dating of the time of emplacement of igneous rocks using the K-Ar isotopic system is a relatively straightforward procedure if suitable analytical facilities and samples of appropriate, fresh, primary minerals are available. In the case of intrusions in coal seams, however, the occurrence of fresh, primary minerals is very rare due to widespread alteration produced by interaction between the igneous rock and fluids in the coal seam. This interaction produces a variety of secondary minerals with most primary minerals and glass being altered to clays (mainly kaolinite) and carbonates. Consequently, relatively few isotopic dates for intrusions into coal seams have been determined. A detailed study of several hundred samples of igneous rocks from the Sydney Basin found only six samples of intrusions into coal seams that were suitable for conventional K-Ar dating (Carr and Facer 1980). Techniques for K-Ar dating of authigenic illite, developed in response to the need by the petroleum industry to understand the timing of diagenesis in petroleum source-rocks and reservoirs, are now well established (Clauer and Chaudhuri 1995). As part of a larger project on the impact of igneous intrusions on coal mining and the alienation of coal reserves, a preliminary investigation of the timing of

Concentrations of lithium in Chinese coals

Energy Technology Data Exchange (ETDEWEB)

Sun, Yuzhuang; Li, Yanheng; Zhao, Cunliang; Lin, Mingyue; Wang, Jinxi; Qin, Shenjun [Hebei University of Engineering, Handan (China). Key Laboratory of Resource Exploration Research of Hebei Province

2010-04-15

Lithium is an important energy metal. Its concentrations in coals have been studied by many geologists. Its average content is only 14 mg/kg in the coals of the world. Lithium has never been reported as a coal associated deposit before. In order to study the concentrations in Chinese coals, 159 coal and gangue samples were taken from six coal mines and were determined by ICP-MS and the minerals in the samples were identified by X-ray powder diffraction. The results indicate that the Li contents in the coal samples from the Antaibao Coal Mine have reached the industry grade of coal associated deposits. In Tongxing Coal Mine, Li contents in the coal floor rock samples have reached the industry grade of independent lithium deposits. Main minerals are polylithionite, triphylite, zinnwaldite, lithionite and cookeite, which were transported into the peats. Therefore, lithium enriched is most likely in the synsedimentary stage in both coal mines. Furthermore, a revised average Li content in Chinese coals was given.

Gamma radiation at coal mines and sections

International Nuclear Information System (INIS)

Pavlov, I.V.; Kuznetsov, A.T.

1991-01-01

The problem of radiation background in coal miner and open pits conditioned by γ-radiation of coals and enclousing rocks containing natural radioactive isotopes ( 40 K, 226 Ra, 232 Th) is analyzed. The data are presented on average content of the above isotopes in coals, hard rocks and earth crest; γ-dose rate in mines and open pits as well as on possible limits and average values of external γ-radiation in mines. It is shown that external γ-radiation is an insignificant factor of radiation hazard in mines and open pits. Systematic monitoring of and accounting for external radiation dose of the personnel are required only in mines where average concentration of 226 Ra exceeds 200 Bqxkg -1 , and that of 232 Th - 150 Bqxkg -1

Rock stress measurements. Preparatory stage of the equipment development project

International Nuclear Information System (INIS)

Mononen, S.; Hakala, M.; Mikkola, P.

2002-01-01

In recent years the rock stress measurement methods used in Finland have been overcoring and hydraulic fracturing. There have been mainly two companies involved in these measurements, namely Suomen Malmi Oy (Smoy) and SwedPower AB. Smoy has done measurements for mines and for rock engineering projects, whereas SwedPower AB has mainly been involved in nuclear waste disposal investigations and conducted hydraulic fracturing measurements in deep boreholes. Smoy together with its partners started in February 2001 a project named JTM, which was a preliminary stage for a future project, which aims to develop a device most suitable for rock stress measurements in Finland. The partners in the project were HUT Rock Engineering, Posiva Oy, Saanio and Riekkola Oy, Gridpoint Finland Oy and Geopros Oy. Tekes, the National Technology Agency, provided almost half of the project funding. In the management group of the project were Pekka Mikkola (chairman) and Tero Laurila from Smoy, Pekka Saerkkae and Sakari Mononen (full-time researcher) from HUT, Aimo Hautojaervi (Posiva Oy), Erik Johansson (Saanio and Riekkola Oy), Matti Hakala (Gridpoint Finland Oy) and Heikki Haemaelaeinen (Geopros Oy). The aim of the JTM-project was to find out the needs for the development of a device most suitable for rock stress measurements in Finnish mines and rock engineering projects. During the project work was done to find out the range of rock stress measurement devices available, to find out the needs for measurements, and to get acquainted to the measurements done in Scandinavia. Also a report of the most suitable methods for Finnish rock conditions was done based on literature and on interviews of rock stress experts. Based on all the information collected during the project a clear picture of the needs for rock stress measurements in Finland could be formed and a preliminary plan of a future project was done. The aim of the suggested project is to build a device based on hydraulic fracturing

Measurement and modeling of advanced coal conversion processes

Energy Technology Data Exchange (ETDEWEB)

Solomon, P.R.; Serio, M.A.; Hamblen, D.G.; Smoot, L.D.; Brewster, B.S. (Advanced Fuel Research, Inc., East Hartford, CT (United States) Brigham Young Univ., Provo, UT (United States))

1991-01-01

The overall objective of this program is the development of predictive capability for the design, scale up, simulation, control and feedstock evaluation in advanced coal conversion devices. This program will merge significant advances made in measuring and quantitatively describing the mechanisms in coal conversion behavior. Comprehensive computer codes for mechanistic modeling of entrained-bed gasification. Additional capabilities in predicting pollutant formation will be implemented and the technology will be expanded to fixed-bed reactors.

Roof instability characteristics and pre-grouting of the roof caving zone in residual coal mining

Science.gov (United States)

Zhao, Tong; Liu, Changyou

2017-12-01

Abandoned roadways and roof caving zones are commonly found in residual coal, and can destroy the integrity of the coal seam and roof. Resulting from mining-induced stress, continuous collapse and fracture instability in roof caving zones (RCZs) jeopardize the safety and efficiency of residual coal mining. Based on the engineering geology conditions of remining face 3101 in Shenghua Mine, the roof fracture and instability features of the RCZ were analyzed through physical simulation, theoretical analysis, and field measurements. In this case, influenced by the RCZ, the main roof across the RCZ fractured and rotated towards the goaf, greatly increasing the working resistance, and crushing the supports. The sudden instability of the coal pillars weakened its support of the main roof, thus resulting in long-key blocks across the RCZ and hinged roof structures, which significantly decreased the stability of the underlying immediate roof. This study establishes a mechanical model for the interactions between the surrounding rock and the supports in the RCZ, determines the reasonable working resistance, and examines the use of pre-grouting solidification restoration technology (PSRT) to solidify the RCZ and reinforce the coal pillars—thus increasing their bearing capacity. Field measurements revealed no roof flaking, inhomogeneous loading or support crushing, indicating that the PSRT effectively controlled the surrounding rock of the RCZ.

Proposal of rock mass behavior classification based on convergence measurement in shaft sinking through sedimentary soft rocks

International Nuclear Information System (INIS)

Tsusaka, Kimikazu

2010-01-01

Japan Atomic Energy Agency has been excavating deep shafts through sedimentary soft rocks in Horonobe, Hokkaido. From the viewpoint of the observational construction, site engineers need a practical guide to evaluate the field measurements conducted with shaft sinking. The author analyzed the relationship among initial deformation rate, observed deformation, the ratio of the modulus of elasticity of rock mass to the initial stress, and the magnitude of inelastic behavior of rock based on convergence measurements and investigation of rock mass properties on shaft walls. As a result, the rock mass behavior classification for shaft sinking which consists of three classes was proposed. (author)

Coal forming conditions for coal seams and coal measures of the Heshan Group Upper Permian Series in Guangxi Province (part 1)

Energy Technology Data Exchange (ETDEWEB)

Li, Y.

1980-10-01

Coal forming conditions for the coal measures of the Heshan Group are discussed based on the analysis of the historical background and paleogeographical environment of the Permian in Guangxi Province. The roof, floor, and partings of the seams are composed of algal micritic limestone, therefore affirming that the central part of Guangxi Province in the late Permian was a typical epi-continental sea. The compensative deposit of algea on the carbonate platform in very shallow water created the conditions for the occurrence of the peat swamp and established the supra-tidal swampy facies. The environment for the accumulation of the major coal seams are analyzed. (In Chinese)

Rock engineering in Finland

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

Contains a large collection of short articles concerned with tunnels and underground caverns and their construction and use. The articles are grouped under the following headings: use of the subsurface space; water supply; waste water services; energy management (includes articles on power stations, district heating and oil storage and an article on coal storage); multipurpose tunnels; waste disposal; transport; shelters; sporting and recreational amenities located in rock caverns; storage facilities; industrial, laboratory, and service facilities; rock foundations; tourism and culture; utilization of rock masses; research on the disposal of nuclear waste; training and research in the field of rock engineering; site investigation techniques; design of structures in rock; construction; the environment and occupational safety; modern equipment technology; underground space in Helsinki.

Temporal and spatial variability of acid rock drainage in a rehabilitated coal mine, Wangaloa, South Otago, New Zealand

International Nuclear Information System (INIS)

Begbie, M.; Craw, D.; Rufaut, C.; Martin, C.

2007-01-01

The Wangaloa open cast coal mine ceased operations in 1989, with no restoration of the 252 ha site, and moderate acid rock drainage developed. A major rehabilitation programme was initiated in 2002 with removal of exotic vegetation, and extensive planting (>60,000) of native seedlings was begun in 2003. By 2006, most seedlings were thriving, and, combined with adventive exotic weeds, a 70% vegetation cover had been achieved. The site substrates were highly variable on the 10-100 m 2 scale, and have been characterised by paste pH (>700 measurements). In 2003, substrates had moderate acidity (pH 4.5 ± 0.9) with distinctly acid patches (pH down to 100 samples from 15 sites) were also highly variable spatially and temporally. Incoming stream and rainwater (pH 5-6) chemically interacted with acid substrates, especially waste rock piles that contain pyrite-bearing material, and evolved to lower pH (pH down to 3.4), sulfate-rich waters. A pit lake on the site receives most surface and groundwater runoff, and this lake, with a water residence time of 1-2 yr, controls the site discharge water quality. The lake pH varies on a monthly time-scale from 4.5 to 6.5, synchronised with pH variations in groundwater boreholes in waste rock. In addition, there has been a general increase in pH of the lake during rehabilitation from consistent pH 4.6-4.8 before rehabilitation to near pH 6 during rehabilitation. The sulfate/chloride ratio of lake water has decreased from 20 to <10 during rehabilitation as well. These changes in lake water composition from year to year may be a result of increased input of rainwater that has had less interaction with substrate than runoff water had before rehabilitation began. (author). 23 refs., 10 figs., 1 tab

Xenon NMR measurements of permeability and tortuosity in reservoir rocks.

Science.gov (United States)

Wang, Ruopeng; Pavlin, Tina; Rosen, Matthew Scott; Mair, Ross William; Cory, David G; Walsworth, Ronald Lee

2005-02-01

In this work we present measurements of permeability, effective porosity and tortuosity on a variety of rock samples using NMR/MRI of thermal and laser-polarized gas. Permeability and effective porosity are measured simultaneously using MRI to monitor the inflow of laser-polarized xenon into the rock core. Tortuosity is determined from measurements of the time-dependent diffusion coefficient using thermal xenon in sealed samples. The initial results from a limited number of rocks indicate inverse correlations between tortuosity and both effective porosity and permeability. Further studies to widen the number of types of rocks studied may eventually aid in explaining the poorly understood connection between permeability and tortuosity of rock cores.

major oxides and trace element distributions in coal and coaly shale ...

African Journals Online (AJOL)

Admin

Coal is a complex organic rock comprised mainly of decayed plants conditioned by syngenetic, diagenetic, epigenetic and detrital inorganic elements. (Orem and Finkelman, 2003). Coal has been globally recognised as an important source of energy. Geological epoch favouring the formation of coal include.

Determination of coal bed quality in wells by geophysical methods

International Nuclear Information System (INIS)

Popov, V.V.

1974-01-01

The dependence of the specific electric resistivity of coal and terrigenous material of the Donbass region on the degree of their metamorphism is discussed. From this dependence a method is derived to determine the metamorphism of coal from the effective specific resistivity of rocks by taking into account the self-polarisation and the density of the coal layers. The degree of metamorphism (from the coefficient of gas components in the heating mass of coal) is obtained with a standard deviation of 2.9%. Special physical properties of coal are related to its qualitative composition in a complex and very close way. With the whole complex of geophysical measurements the quality parameters can be estimated in more detail. For the Pavlogradsij-Petropavlovskij region of the Donbass non-linear mutli-dimensional relations between the quality parmaeters of coal are derived, and the measurements with standard geophysical methods (resistivity-, spontaneous-potential-, latero-, calibre- and gamma-gamma-log as well as cavernometry) are presented. The results obtained with these methods are tested by a comparison with 8 samples from mines. The standard deviation for the ash content is 3.73% (for core sampling 1.0%) and for the thickness of the plastic layer 3.63 mm (for core sampling 3.34mm)

Measurement of rock properties at elevated pressures and temperatures

International Nuclear Information System (INIS)

Pincus, H.J.; Hoskins, E.R.

1985-01-01

The papers in this volume were presented at an ASTM symposium held on 20 June 1983 in conjunction with the 24th Annual Rock Mechanics Symposium at Texas A and M University, College Station, TX. The purpose of these papers is to present recent developments in the measurement of rock properties at elevated pressures and temperatures, and to examine and interpret the data produced by such measurement. The need for measuring rock properties at elevated pressures and temperatures has become increasingly important in recent years. Location and design of nuclear waste repositories, development of geothermal energy sites, and design and construction of deep excavations for civil, military, and mining engineering require significantly improved capabilities for measuring rock properties under conditions substantially different from those prevailing in most laboratory and in situ work. The development of high-pressure, high-temperature capabilities is also significant for the analysis of tectonic processes

Revised stratigraphy of the Permian Bainmedart coal measures, northern Prince Charles Mountains, east Antarctica

Energy Technology Data Exchange (ETDEWEB)

McLoughlin, S.; Drinnan, A.N. [University of Melbourne, Parkville, Vic. (Australia). School of Botany

1997-05-01

The Bainmedart Coal Measures constitute the middle portion of the Permian-Triassic Amery Group, which represents the only substantial Palaeozoic-Mesozoic sedimentary succession exposed in eastern Antarctica outside the Transantarctic Mountains. The coal measures overlie alluvial fan deposits of the Radok Conglomerate and are conformably overlain by the dominantly fluviatile Flagstone Bench Formation. The coal measures were deposited within alluvial settings dominated by north to northeasterly flowing, low-sinuosity rivers chiefly confined to broad, fault-bounded, valleys of the Lambert Graben, a major late Palaeozoic to early Mesozoic failed rift system. Both climatic and local tectonic factors are considered to have been the major influences on the pattern of coal measure sedimentation. Recent mapping has identified a much greater thickness of sediments within the coal measures than had been inferred previously. The Bainmedart Coal Measures are formally subdivided into six members. In ascending stratigraphic order these are: Dart Fields Conglomerate Member ({lt} 3m thick), Toploje Member (300 m thick), Dragons Teeth Member (15-25 m thick), Glossopteris Gully Member (670 m thick), Grainer Member (350 m thick), acid McKinnon Member (530 m thick).

3D Discrete element approach to the problem on abutment pressure in a gently dipping coal seam

Science.gov (United States)

Klishin, S. V.; Revuzhenko, A. F.

2017-09-01

Using the discrete element method, the authors have carried out 3D implementation of the problem on strength loss in surrounding rock mass in the vicinity of a production heading and on abutment pressure in a gently dripping coal seam. The calculation of forces at the contacts between particles accounts for friction, rolling resistance and viscosity. Between discrete particles modeling coal seam, surrounding rock mass and broken rocks, an elastic connecting element is introduced to allow simulating coherent materials. The paper presents the kinematic patterns of rock mass deformation, stresses in particles and the graph of the abutment pressure behavior in the coal seam.

Characterization of rock samples and mineralogical controls on leachates

Science.gov (United States)

Hammarstrom, Jane M.; Cravotta, Charles A.; Galeone, Daniel G.; Jackson, John C.; Dulong, Frank T.; Hornberger, Roger J.; Brady, Keith B.C.

2009-01-01

Rocks associated with coal beds typically include shale, sandstone, and (or) limestone. In addition to common rock-forming minerals, all of these rock types may contain sulfide and sulfate minerals, various carbonate minerals, and organic material. These different minerals have inherently different solubility characteristics, as well as different acid-generating or acid-neutralizing potentials. The abundance and composition of sulfur- and carbonate-bearing minerals are of particular interest in interpreting the leaching column data because (1) pyrite and carbonate minerals are the primary controls on the acid-base account of a sample, (2) these minerals incorporate trace metals that can be released during weathering, and (3) these minerals readily react during weathering due to mineral dissolution and oxidation of iron.Rock samples were collected by the Pennsylvania Department of Environmental Protection (PaDEP) from five different sites to assess the draft standardized leaching column method (ADTI-WP2) for the prediction of weathering rates and water quality at coal mines. Samples were sent to USGS laboratories for mineralogical characterization and to ActLabs for chemical analysis. The samples represent a variety of rock types (shales, sandstones, and coal refuse) that are typical of coal overburden in the eastern United States. These particular samples were chosen for testing the weathering protocols because they represent a range of geochemical and lithologic characteristics, sulfur contents, and acid-base accounting characteristics (Hornberger et al., 2003). The rocks contain variable amounts of pyrite and carbonate minerals and vary in texture.This chapter includes bulk rock chemical data and detailed mineralogical and textural data for unweathered starting materials used in the interlaboratory validation study, and for two samples used in the early phases of leaching column tests (Wadesville Sandstone, Leechburg Coal Refuse). We also characterize some of the

Mercury emission, control and measurement from coal combustion

Energy Technology Data Exchange (ETDEWEB)

Pan, Wei-Ping [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering; Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Cao, Yan [Western Kentucky Univ., Bowling Green, KY (United States). Inst. for Combustion Science and Environmental Technology; Zhang, Kai [North China Electric Power Univ., Beijing (China). School of Energy and Power Engineering

2013-07-01

Coal-fired electric power generation accounts for 65% of U.S. emissions of sulfur dioxide (SO2), 22% of nitrogen oxides (NOx), and 37% of mercury (Hg). The proposed Clear Air Interstate Rule (CAIR) and Clean Air Mercury Rule (CAMR) will attempt to regulate these emissions using a cap-and-trade program to replace a number of existing regulatory requirements that will impact this industry over the next decade. Mercury emissions remain the largest source that has not yet been efficiently controlled, in part because this is one of the most expensive to control. Mercury is a toxic, persistent pollutant that accumulates in the food chain. During the coal combustion process, when both sampling and accurate measurements are challenging, we know that mercury is present in three species: elemental, oxidized and particulate. There are three basic types of mercury measurement methods: Ontario Hydro Method, mercury continuous emission monitoring systems (CEMS) and sorbent-based monitoring. Particulate mercury is best captured by electrostatic precipitators (ESP). Oxidized mercury is best captured in wet scrubbers. Elemental mercury is the most difficult to capture, but selective catalytic reduction units (SCRs) are able to convert elemental mercury to oxidized mercury allowing it to be captured by wet flue gas desulfurization (FGD). This works well for eastern coals with high chlorine contents, but this does not work well on the Wyoming Powder River Basin (PRB) coals. However, no good explanation for its mechanism, correlations of chlorine content in coal with SCR performance, and impacts of higher chlorine content in coal on FGD re-emission are available. The combination of SCR and FGD affords more than an 80% reduction in mercury emissions in the case of high chlorine content coals. The mercury emission results from different coal ranks, boilers, and the air pollution control device (APCD) in power plant will be discussed. Based on this UAEPA new regulation, most power plants

Mine Water Treatment in Hongai Coal Mines

Science.gov (United States)

Dang, Phuong Thao; Dang, Vu Chi

2018-03-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

Risk factors for the undermined coal bed mining method

Energy Technology Data Exchange (ETDEWEB)

Arad, V. [Petrosani Univ., Petrosani (Romania). Dept. of Mining Engineering; Arad, S. [Petrosani Univ., Petrosani (Romania). Dept of Electrical Engineering

2009-07-01

The Romanian mining industry has been in a serious decline and is undergoing ample restructuring. Analyses of reliability and risk are most important during the early stages of a project in guiding the decision as to whether or not to proceed and in helping to establish design criteria. A technical accident occurred in 2008 at the Petrila coal mine involving an explosion during the exploitation of a coal seam. Over time a series of technical accidents, such as explosions and ignitions of methane gas, roof blowing phenomena or self-ignition of coal and hazard combustions have occurred. This paper presented an analysis of factors that led to this accident as well an analysis of factors related to the mining method. Specifically, the paper discussed the geomechanical characteristics of rocks and coal; the geodynamic phenomenon from working face 431; the spontaneous combustion phenomenon; gas accumulation; and the pressure and the height of the undermined coal bed. It was concluded that for the specific conditions encountered in Petrila colliery, the undermined bed height should be between 5 and 7 metres, depending on the geomechanic characteristics of coal and surrounding rocks. 8 refs., 1 tab., 3 figs.

Characterization of airborne float coal dust emitted during continuous mining, longwall mining and belt transport.

Science.gov (United States)

Shahan, M R; Seaman, C E; Beck, T W; Colinet, J F; Mischler, S E

2017-09-01

Float coal dust is produced by various mining methods, carried by ventilating air and deposited on the floor, roof and ribs of mine airways. If deposited, float dust is re-entrained during a methane explosion. Without sufficient inert rock dust quantities, this float coal dust can propagate an explosion throughout mining entries. Consequently, controlling float coal dust is of critical interest to mining operations. Rock dusting, which is the adding of inert material to airway surfaces, is the main control technique currently used by the coal mining industry to reduce the float coal dust explosion hazard. To assist the industry in reducing this hazard, the Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health initiated a project to investigate methods and technologies to reduce float coal dust in underground coal mines through prevention, capture and suppression prior to deposition. Field characterization studies were performed to determine quantitatively the sources, types and amounts of dust produced during various coal mining processes. The operations chosen for study were a continuous miner section, a longwall section and a coal-handling facility. For each of these operations, the primary dust sources were confirmed to be the continuous mining machine, longwall shearer and conveyor belt transfer points, respectively. Respirable and total airborne float dust samples were collected and analyzed for each operation, and the ratio of total airborne float coal dust to respirable dust was calculated. During the continuous mining process, the ratio of total airborne float coal dust to respirable dust ranged from 10.3 to 13.8. The ratios measured on the longwall face were between 18.5 and 21.5. The total airborne float coal dust to respirable dust ratio observed during belt transport ranged between 7.5 and 21.8.

Mine Water Treatment in Hongai Coal Mines

OpenAIRE

Dang Phuong Thao; Dang Vu Chi

2018-01-01

Acid mine drainage (AMD) is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine ...

National coal resource assessment non-proprietary data: Location, stratigraphy, and coal quality for selected tertiary coal in the Northern Rocky Mountains and Great Plains region

Science.gov (United States)

Flores, Romeo M.; Ochs, A.M.; Stricker, G.D.; Ellis, M.S.; Roberts, S.B.; Keighin, C.W.; Murphy, E.C.; Cavaroc, V.V.; Johnson, R.C.; Wilde, E.M.

1999-01-01

One of the objectives of the National Coal Resource Assessment in the Northern Rocky Mountains and Great Plains region was to compile stratigraphic and coal quality-trace-element data on selected and potentially minable coal beds and zones of the Fort Union Formation (Paleocene) and equivalent formations. In order to implement this objective, drill-hole information was compiled from hard-copy and digital files of the: (1) U.S. Bureau of Land Management (BLM) offices in Casper, Rawlins, and Rock Springs, Wyoming, and in Billings, Montana, (2) State geological surveys of Montana, North Dakota, and Wyoming, (3) Wyoming Department of Environmental Quality in Cheyenne, (4) U.S. Office of Surface Mining in Denver, Colorado, (5) U.S. Geological Survey, National Coal Resource Data System (NCRDS) in Reston, Virginia, (6) U.S. Geological Survey coal publications, (7) university theses, and (8) mining companies.

Characterization of Unstable Rock Slopes Through Passive Seismic Measurements

Science.gov (United States)

Kleinbrod, U.; Burjanek, J.; Fäh, D.

2014-12-01

Catastrophic rock slope failures have high social impact, causing significant damage to infrastructure and many casualties throughout the world each year. Both detection and characterization of rock instabilities are therefore of key importance. An analysis of ambient vibrations of unstable rock slopes might be a new alternative to the already existing methods, e.g. geotechnical displacement measurements. Systematic measurements have been performed recently in Switzerland to study the seismic response of potential rockslides concerning a broad class of slope failure mechanisms and material conditions. Small aperture seismic arrays were deployed at sites of interest for a short period of time (several hours) in order to record ambient vibrations. Each measurement setup included a reference station, which was installed on a stable part close to the instability. Recorded ground motion is highly directional in the unstable parts of the rock slope, and significantly amplified with respect to stable areas. These effects are strongest at certain frequencies, which were identified as eigenfrequencies of the unstable rock mass. In most cases the directions of maximum amplification are perpendicular to open cracks and in good agreement with the deformation directions obtained by geodetic measurements. Such unique signatures might improve our understanding of slope structure and stability. Thus we link observed vibration characteristics with available results of detailed geological characterization. This is supported by numerical modeling of seismic wave propagation in fractured media with complex topography.For example, a potential relation between eigenfrequencies and unstable rock mass volume is investigated.

Design and development of a dust dispersion chamber to quantify the dispersibility of rock dust.

Science.gov (United States)

Perera, Inoka E; Sapko, Michael J; Harris, Marcia L; Zlochower, Isaac A; Weiss, Eric S

2016-01-01

Dispersible rock dust must be applied to the surfaces of entries in underground coal mines in order to inert the coal dust entrained or made airborne during an explosion and prevent propagating explosions. 30 CFR. 75.2 states that "… [rock dust particles] when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air …" However, a proper definition or quantification of "light blast of air" is not provided. The National Institute for Occupational Safety and Health (NIOSH) has, consequently, designed a dust dispersion chamber to conduct quantitative laboratory-scale dispersibility experiments as a screening tool for candidate rock dusts. A reproducible pulse of air is injected into the chamber and across a shallow tray of rock dust. The dust dispersed and carried downwind is monitored. The mass loss of the dust tray and the airborne dust measurements determine the relative dispersibility of the dust with respect to a Reference rock dust. This report describes the design and the methodology to evaluate the relative dispersibility of rock dusts with and without anti-caking agents. Further, the results of this study indicate that the dispersibility of rock dusts varies with particle size, type of anti-caking agent used, and with the untapped bulk density. Untreated rock dusts, when wetted and dried forming a cake that was much less dispersible than the reference rock dust used in supporting the 80% total incombustible content rule.

Spontaneous combustion of the Upper Paleocene Cerrejon Formation coal and generation of clinker in La Guajira Peninsula (Caribbean Region of Colombia)

Energy Technology Data Exchange (ETDEWEB)

Quintero, J.A. [Carbones del Cerrejon Limited., Cl. 100 No. 19-54 piso 12, Bogota D.C. (Colombia); Candela, S.A. [ECOPETROL S.A. Edificio Principal Cr. 7 No. 37-65, Bogota D.C. (Colombia); Rios, C.A. [Escuela de Geologia, Universidad Industrial de Santander, Cr 27 Cl 9, Ciudad Universitaria, Bucaramanga (Colombia); Montes, C. [Smithsonian Tropical Research Institute, Roosvelt Ave., Tupper Building - 401, Balboa, Ancon, Panama (Panama); Uribe, C. [Tubos Moore S.A. Cll 99 No. 57-74, Bogota (Colombia)

2009-12-01

Clinker referred here as red and brick-looking burnt rocks found interbedded in the Upper Paleocene Cerrejon Formation is the result of spontaneous and natural combustion of coal seams in the recent geologic past. These rocks have been mapped, measured and characterized in the Cerrejon Coal Mine at La Guajira Peninsula (Colombia). These burnt rocks usually outcrop in irregular patterns as almost tabular bodies up to 100 m thick, thinning and pinching out below ground surface to depths up to 448 m. Mapping revealed that clinker is usually found near deformed zones, either faults or tight folds. Timing of spontaneous combustion seems to predate folding and faulting, but seems to postdate the development of the Cerrejon thrust fault and alluvial fan proceeding from the Perija Range. Clinker covers an area of around 2.9 x 10{sup 6} m{sup 2} with a volume of approximately 1.4 x 10{sup 8} m{sup 3}. The calculation of the amount of heat released through coal burning indicates that complete combustion of 6.4 Mt of 26.4 x 10{sup 6} J/kg coal would yield 17 x 10{sup 13} J. (author)

Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

Directory of Open Access Journals (Sweden)

Jinyi TAO

2014-09-01

Full Text Available The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These parameters are magnetic permeability m (H/m, dielectric constant e (F/m and electrical conductivity s (S/m. In these parameters, electrical conductivity is not constant. Under the influence of various factors, it will be great changes. This paper, for the specific circumstances of coal mine rock, discuses and conduct dada mining the effect frequency on the electrical conductivity of underground rock in coal mine with through-the-earth wireless communication.

Pemodelan Penyebaran Batuan Potensial Pembentuk Asam Pada Kawasan Penambangan Batubara Tambang Terbuka Di Muara Lawa, Kabupaten Kutai Barat, Kalimantan Timur (Modeling Distribution of Rock Potential Acid Forming in Open Pit Coal Mining Areas)

OpenAIRE

Devy, Shalaho Dina; Hendrayana, Heru; Putra, Dony Prakasa Eka; Sugiharto, Eko

2016-01-01

The impact of open pit coal mining is the emergence of Acid Mine Water (AMD) around the mining environment that affect the quality of the mine water, aquatic biota, water and soil quality. Therefore, early information to anticipate these impacts is the identification potential acid rock and distribution model as a guide for the mining plan. Geological and geochemical study of rocks is important in knowing the distribution of rock Potential Acid Formning (PAF) and Non Acid Forming (NAF). Minin...

In Situ Test Study of Characteristics of Coal Mining Dynamic Load

Directory of Open Access Journals (Sweden)

Jiang He

2015-01-01

Full Text Available Combination of coal mining dynamic load and high static stress can easily induce such dynamic disasters as rock burst, coal and gas outburst, roof fall, and water inrush. In order to obtain the characteristic parameters of mining dynamic load and dynamic mechanism of coal and rock, the stress wave theory is applied to derive the relation of mining dynamic load strain rate and stress wave parameters. The in situ test was applied to study the stress wave propagation law of coal mine dynamic load by using the SOS microseismic monitoring system. An evaluation method for mining dynamic load strain rate was proposed, and the statistical evaluation was carried out for the range of strain rate. The research results show that the loading strain rate of mining dynamic load is in direct proportion to the seismic frequency of coal-rock mass and particle peak vibration velocity and is in inverse proportion to wave velocity. The high-frequency component damps faster than the low-frequency component in the shockwave propagating process; and the peak particle vibration velocity has a power functional relationship with the transmitting distance. The loading strain rate of mining dynamic load is generally less than class 10−1/s.

Method for processing coal-enrichment waste with solid and volatile fuel inclusions

Science.gov (United States)

Khasanova, A. V.; Zhirgalova, T. B.; Osintsev, K. V.

2017-10-01

The method relates to the field of industrial heat and power engineering. It can be used in coal preparation plants for processing coal waste. This new way is realized to produce a loose ash residue directed to the production of silicate products and fuel gas in rotary kilns. The proposed method is associated with industrial processing of brown coal beneficiation waste. Waste is obtained by flotation separation of rock particles up to 13 mm in size from coal particles. They have in their composition both solid and volatile fuel inclusions (components). Due to the high humidity and significant rock content, low heat of combustion, these wastes are not used on energy boilers, they are stored in dumps polluting the environment.

Battling coal and rock dust in mines. Bor'ba s ugol'noi i porodnoi pyl'yu v shakhtakh

Energy Technology Data Exchange (ETDEWEB)

Petrukhin, P.M.; Grodel, G.S.; Korenev, A.P.; Krivokhizha, B.M.; Kul' bachnyi, A.N.; Lyubimova, A.I.; Medvedev, E.N.; Yaremachenko, P.P.; Zhilyaev, N.I.

1981-01-01

The problems of comprehensive removal of dust from the atmosphere in mines are discussed. Physical and pnysicochemical properties of mine dust are described, which are important for estimating the processes of its formation, spread, and suppression. Presented are the results of theoretical and natural studies of dust aerodynamics of mines. Modern methods for battling coal and rock dust in mines, as well as means of monitoring the dust level of the air are outlined. Technical descriptions are given for new instruments for changing the dust level of the air. Brief reports are given on the preliminary wetting of coal in the massif, and theoretical and practical problems are discussed concerning hydrological methods of dust removal, dust suppression by foam, and dust trapping during the operation of mining equipment, and also on removal of dust from the air at the surface complex of a mine.

Side abutment pressure distribution by field measurement

Energy Technology Data Exchange (ETDEWEB)

Lian-guo Wang; Yang Song; Xing-hua He; Jian Zhang [State Key Laboratory for Geomechanics and Deep Underground Engineering, Xuzhou (China)

2008-12-15

Given the 7123 working face in the Qidong Coal Mine of the Wanbei Mining Group, nine dynamic roof monitors were installed in the crossheading to measure the amount and velocity of roof convergence in different positions and at different times and three steel bored stress sensors were installed in the return airway to measure rock stress at depth. On the basis of this arrangement, the rule of change of the distribution of the side abutment pressure with the advance of the working face and movement of overlying strata was studied. The rule of change and the stability of rock stress at depth were measured. Secondly, the affected area and stability time of the side abutment pressure were also studied. The results show that: 1) During working, the face advanced distance was from 157 m to 99 m, the process was not effected by mining induced pressure. When the distance was 82 m, the position of peak stress was 5 m away from the coal wall. When the distance was 37 m, the position of peak stress away from the coal wall was about 15 m to 20 m and finally reached a steady state; 2) the time and the range of the peak of side rock pressure obtained from stress sensors were consistent with the results from the dynamic roof monitors; 3) the position of the peak pressure was 25 m away from the coal wall. 14 refs., 6 figs.

Mine Water Treatment in Hongai Coal Mines

Directory of Open Access Journals (Sweden)

Dang Phuong Thao

2018-01-01

Full Text Available Acid mine drainage (AMD is recognized as one of the most serious environmental problem associated with mining industry. Acid water, also known as acid mine drainage forms when iron sulfide minerals found in the rock of coal seams are exposed to oxidizing conditions in coal mining. Until 2009, mine drainage in Hongai coal mines was not treated, leading to harmful effects on humans, animals and aquatic ecosystem. This report has examined acid mine drainage problem and techniques for acid mine drainage treatment in Hongai coal mines. In addition, selection and criteria for the design of the treatment systems have been presented.

Characterization of Rare Earth Element Minerals in Coal Utilization Byproducts

Energy Technology Data Exchange (ETDEWEB)

Montross, Scott N. [Oak Ridge Inst. for Science and Education (ORISE), Oak Ridge, TN (United States); Verba, Circe A. [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center; Collins, Keith [National Energy Technology Lab. (NETL), Albany, OR (United States). Research Innovation Center

2017-07-17

occurrence of REE mineral phases in CUB and allowed us to calculate structural and volumetric estimates of REE. Collectively, the rock and coal ash samples contained minerals such as quartz, kaolinite, muscovite/illite, iron oxide (as hematite or magnetite), mullite, and clinochlore. Trace minerals included pyrite, zircon, siderite, rutile, diopside, foresterite, gypsum, and barite. We identified REE phosphate minerals monazite (Ce,La,Nd,Th)(PO₄,SiO₄), xenotime (YPO₄,SiO₄), and apatite (Ca₅(PO₄)₃(F,Cl,OH) via SEM and electron microprobe analysis: these materials generally occurred as 1-10 μm-long crystals in the rock and ash samples. As has been shown in other studies, amorphous material-aluminosilicate glass or iron oxyhydroxide-are the major components of coal fly and bottom ash. Trace amounts of amorphous calcium oxide and mixed element (e.g., Al-Si-Ca-Fe) slag are also present. Quartz, mullite, hematite, and magnetite are the crystalline phases present. We found that REEs are present as monomineralic grains dispersed within the ash, as well as fused to or encapsulated by amorphous aluminosilicate glass particles. Monazite and xenotime have relatively high melting points (>1800 °C) compared to typical combustion temperatures; our observations indicate that the REE-phosphates, which presumably contribute a large percentage of REE to the bulk ash REE pool, as measured by mass spectroscopy, are largely unaltered by the combustion. Our study shows that conventional coal combustion processes sequester REE minerals into aluminosilicate glass phases, which presents a new engineering challenge for extracting REE from coal ash. The characterization work summarized in this report provides a semi-quantitative assessments of REE in coal-containing rock and CUB. The data we obtained from 2- and 3-D imaging, elemental mapping, volumetric estimates, and advanced high-resolution pixel classification

An evaluation of fracture toughness of bituminous coal

International Nuclear Information System (INIS)

Pathan, A.G.

2005-01-01

The role of fracture mechanics in the design of rock structures is vitally important. However, because of the complexities of rock structures and lack of understanding of the fundamentals of the failure mechanism, it has become customary to use the engineering properties approach in the design of stable rock structures. Recently considerable attention has been given and attempts are being made to apply the fracture mechanics approach to the design of safe mining structures. In mining engineering the fracture mechanics may be applied to calculate the formation of fracture zones around mine opening, thus estimating support requirements and formulating guide lines for the selection of mine roadway support system. The research work presented here is concerned with the evaluation of fracture toughness of coal under laboratory conditions. Diametral compression test method is used to determine the fracture toughness parameter of coal in the opening model failure. The effect of crack length and dimensionless crack length on the fracture toughness was studied also. A laboratory investigation of fracture toughness of coal in tensile mode failure has led to the conclusion that fracture toughness could be treated as a material property. (author)

Estimates of water and solute release from a coal waste rock dump in the Elk Valley, British Columbia, Canada.

Science.gov (United States)

Villeneuve, S A; Barbour, S L; Hendry, M J; Carey, S K

2017-12-01

Long term (1999 to 2014) flow and water quality data from a rock drain located at the base of a coal waste rock dump constructed in the Elk Valley, British Columbia was used to characterize the release of three solutes (NO 3 - , Cl - and SO 4 2- ) from the dump and obtain whole dump estimates of net percolation (NP). The concentrations of dump derived solutes in the rock drain water were diluted by snowmelt waters from the adjacent natural watershed during the spring freshet and reached a maximum concentration during the winter baseflow period. Historical peak baseflow concentrations of conservative ions (NO 3 - and Cl - ) increased until 2006/07 after which they decreased. This decrease was attributed to completion of the flushing of the first pore volume of water stored within the dump. The baseflow SO 4 2- concentrations increased proportionally with NO 3 - and Cl - to 2007, but then continued to slowly increase as NO 3 - and Cl - concentrations decreased. This was attributed to ongoing production of SO 4 2- due to oxidation of sulfide minerals within the dump. Based on partitioning of the annual volume of water discharged from the rock drain to waste rock effluent (NP) and water entering the rock drain laterally from the natural watershed, the mean NP values were estimated to be 446±50mm/a (area normalized net percolation/year) for the dump and 172±71mm/a for the natural watershed. The difference was attributed to greater rates of recharge in the dump from summer precipitation compared to the natural watershed where rainfall interception and enhanced evapotranspiration will increase water losses. These estimates included water moving through subsurface pathways. However, given the limitations in quantifying these flows the estimated NP rates for both the natural watershed and the waste rock dump are considered to be low, and could be much higher (e.g. ~450mm/a and ~800mm/a). Copyright © 2017 Elsevier B.V. All rights reserved.

Method of degassifying a massive of rock

Energy Technology Data Exchange (ETDEWEB)

Levin, M M; Krivosheev, V O; Preobrazhenskaia, E I; Talapkerov, A Sh; Taushkin, G T

1979-05-30

This invention concerns the mining industry, chiefly the coal industry, and can be used for the degasification of coal layers and interfering rock. The method of preliminary extraction of gas with underground development of burning minerals, including the pumping of gas through a collector, carried in the plane of the degasifying layer, discharged from rock pressure by means of extracting the lower lying layer, is known. However, the given method does not make it possible to degasify the interfering rock. Another method, consisting of the fact that from the mining development in the lateral rock, chambers are made, from which a group of wells are bored, and the latter are united with the gas removing system, is well known. This method has the inadequacy that the well of each chamber is connected to the gas removing system of the pipelines, and this leads to an increase in the price of the method. A new system is presented for the degasification of the massive of rock which is presented in an illustration...... The advantage of the suggested method consists of the fact that material outlays are reduced for the unification of each chamber with the gas removing pipeline, and besides this, the wells, connecting the chambers are drains for the surrounding rock, which increases the effectiveness of the degasification.

Research status and future trends on surface pre-grouting technology in reforming wall rock of vertical shafts in coal mines in China

Science.gov (United States)

Wang, Hua

2018-02-01

In the mine construction, the surface pre-grouting technology is an important method to prevent water blast in excavation process of vertical shaft when the shaft must pass through the thick, water-rich and high water-pressure bedrock aquifer. It has been nearly 60 years since the technology was used to reform wall rock of vertical shaft in coal mine in China for the first time, and the existing technology can basically meet the needs of constructing 1000m deep vertical shaft. Firstly, the article introduces that in view of Magg’s spherical seepage theory and Karol’s spherical seepage theory, Chinese scholars found that the diffusion of grout from borehole into the surrounding strata in horizontal direction is irregular through a lot of research and engineering practice of using the surface pre-grouting technology to reform wall rock of vertical shafts, and put forward the selecting principles of grout’s effective diffusion radius in one grouting engineering; Secondly, according to the shape of the grouting boreholes, surface pre-grouting technology of vertical shaft is divided into two stages: vertical borehole stage and S-type borehole stage. Thirdly, the development status of grouting materials and grouting equipment for the technology is introduced. Fourthly, grouting mode, stage height and pressure of the technology are introduced. Finally, it points out that with the increasing depth of coal mining in China, the technology of reforming wall rock of 1000~2000m deep vertical shafts will face many problems, such as grouting theory, grouting equipment, grouting finishing standard, testing and evaluation of grouting effect, and so on. And it put forward a preliminary approach to solving these problems. This paper points out future research directions of the surface pre-grouting technology in China.

Primary migration of Jurassic coal-derived oil in Santanghu basin

Energy Technology Data Exchange (ETDEWEB)

Zhang, W.; Zhong, N.; Ren, D. [China University of Mining and Technology, Beijing (China). Dept of Resource Exploitation Engineering

2000-11-01

It is known that the differential evolution of the multiple macerals results in 'oil generation by stage', and that 'early generation, early expulsion' is one of the preconditions for the efficient accumulation of the coal-derived oil. Based upon the study on the evolution of the physical properties, related to the hydrocarbon expulsion, of the Jurassic organic rock in Santanghu basin during the course of maturation, the mechanism of the primary migration of its coal-derived oil was discussed. The rapid loss of the inherent moisture in the organic rock was not accordant with the main generation stage of the coal-derived oil, so it was unrealistic that the oil migrated by dissolution in the expelled water. It is thought that the special forming mechanism of the continuous 'bitumen network' under the condition of over-pressure and an earlier history of primary migration may be essential to the Jurassic coal-derived oil in Santanghu basin. 17 refs., 4 figs.

Determining the ash content of coal flotation tailings using an MPOF optical ash meter

Energy Technology Data Exchange (ETDEWEB)

Sikora, T; Sliwa, J

1982-01-01

The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

Late Cretaceous coal overlying karstic bauxite deposits in the Parnassus-Ghiona Unit, Central Greece: Coal characteristics and depositional environment

Energy Technology Data Exchange (ETDEWEB)

Kalaitzidis, Stavros; Siavalas, George; Christanis, Kimon [Dept. of Geology, University of Patras, 26504 Rio-Patras (Greece); Skarpelis, Nikos [Dept. of Geology and Geoenvironment, University of Athens, 15784 Zografou (Greece); Araujo, Carla Viviane [Petrobras-Cenpes GEOQ/PDEXP, Rua Horacio Macedo n 950, Cidade Universitaria - Ilha do Fundao, 21941-915 Rio de Janeiro (Brazil)

2010-04-01

The Pera-Lakkos coal located on top of bauxite deposits in the Ghiona mining district (Central Greece), is the only known Mesozoic (Late Cretaceous) coal in the country. It was derived from herbaceous plants and algae growing in mildly brackish mires that formed behind a barrier system during a regression of the sea, on a karstified limestone partly filled in with bauxitic detritus. Petrological, mineralogical and geochemical data point to the predominance of reducing conditions and intense organic matter degradation in the palaeomires. O/C vs. H/C and OI vs. HI plots, based on elemental analysis and Rock-Eval data, characterize kerogen types I/II. This reflects the relatively high liptinite content of the coal. Besides kerogen composition, O/C vs. H/C plot for the Pera-Lakkos coals is in accordance with a catagenesis stage of maturation in contrast with vitrinite reflectance and T{sub max} from Rock-Eval pyrolysis, which indicate the onset of oil window maturation stage. Suppression of vitrinite reflectance should be considered and the high liptinite content corroborates this hypothesis. Despite some favourable aspects for petroleum generation presented by the Pera-Lakkos coal, its maximum thickness (up to 50 cm) points to a restricted potential for petroleum generation. Coal oxidation took place either during the late stage of peat formation, due to wave action accompanying the subsequent marine transgression, or epigenetically after the emergence of the whole sequence due to percolation of drainage waters. Both options are also supported by the REE shale-normalized profiles, which demonstrate an upwards depletion in the coal layer. Oxidation also affected pyrite included in the coal; this led to the formation of acidic (sulfate-rich) solutions, which percolated downwards resulting in bleaching of the upper part of the underlying bauxite. (author)

Analysis of rock stress and rock stress measurements with application to Aespoe HRL

International Nuclear Information System (INIS)

Lundholm, Beatrice

2000-11-01

The process of choosing a site for a nuclear waste repository means that many aspects have to be taken into consideration. One of these is that the repository has to be mechanically stable for a long time. The mechanical stability of the rock is very difficult to determine. One of several factors, which determine the mechanical stability, is the virgin state of stress. The thesis project consists of two parts. In the first part the state of stress at Aespoe Hard Rock Laboratory had to be defined. This was done based on earlier rock stress measurements conducted during the years 1988 to 1997. Two different measurement techniques have been used, hydraulic fracturing and overcoring. During the overcoring two types of cells have been used, CSIRO HI-cell and a cell developed by the Swedish State Power Board (SSPB). In the second part of the project, investigation of the correlation between the stress and geological structures are made using numerical modelling tools such as FLAC, UDEC and 3DEC. The rock stress measurements using the hydraulic fracturing gave orientations of the horizontal stress that coincide with earlier hydraulic fracturing measurements conducted in Scandinavia. The magnitudes of rock stresses are slightly lower than the earlier reported stress magnitudes for the Scandinavian part of the earth crust. The rock stresses obtained from the overcoring resulted in higher stresses than what was predicted by the hydraulic fracturing measurements. However, the orientation of the maximum horizontal stresses coincides well between the two techniques. The orientation is also more or less constant with respect to increasing depth. The state of stress at Aespoe is defined by using the results from the hydraulic fracturing and the measurements conducted by SSPB-cell. The measurements from the SSPB-cell are used since these have a Poisson's ratio that corresponds well with the uniaxial tests of rock samples and since the measurements have been done at a distance from

Relationship between the rock mass deformation and places of occurrence of seismological events

Energy Technology Data Exchange (ETDEWEB)

Janusz Makowka; Jozef Kabiesz; Lin-ming Ddou [Central Mining Institute, Katowice (Poland)

2009-09-15

Static effort of rock mass very rarely causes of rock burst in Polish coal mines. Rock bursts with source in the seismic tremor within the roof rock layers are prevailing. A seismic tremor is an effect of rupture or sliding in roof layers above the exploited panel in coal seam, sometime in a distance from actual exploitation. Sliding, as a rule occurs in fault zone and tremors in it are expected, but monolithic layer rupture is very hard to predict. In a past few years a practice of analyzing state of deformation in high energy seismic tremors zones has been employed. It let gathering experience thanks to witch determination of dangerous shape of reformatted roof is possible. In the paper some typical forms of roof rocks deformations leading to seismic tremor occurrence will be presented. In general these are various types of multidirectional rock layers bending. Real examples of seismic events and rock bursts in the Czech Republic will be shown. 5 refs., 6 figs.

Diffusivity and electrical resistivity measurements in rock matrix around fractures

International Nuclear Information System (INIS)

Kumpulainen, H.; Uusheimo, K.

1989-12-01

Microfracturing of rock matrix around permeable fractures was studied experimentally from drill core samples around major fractures. The methods used were diffusion measurements using a 36 Cl-tracer and electrical resistivity measurements. Rock samples were from the Romuvaara investigation site, the granite specimen around a partially filled carbonate fracture (KR4/333 m) and gneiss specimen around a slickenside fracture (KR1/645 m). A consistent difference of one to two orders of magnitude in the levels of the methods with regard to the effective diffusion coefficients for Cl - -ion was found, the electrical resistivity measurement giving higher values. On the basis of the diffusion measurements the diffusion porosities could be calculated but these remained one to two orders of magnitude lower than that expected for granitic rocks using the water saturation method. A possible reason for these differences could have been the low, in some cases 0.004 M NaC1-concentration in the diffusion experiments vs. the 1 M NaCl-concentration used in the electrical resistivity measurements. Due to the small number of specimens and cross sectional areas of only 2 cm 2 , rock inhomogeneity effects were significant making the interpretation of the results somewhat troublesome. Porosities on fracture surfaces seemed to be higher than in the deeper, more intact rock matrix

Relationships between coal-quality and organic-geochemical parameters: A case study of the Hafik coal deposits (Sivas Basin, Turkey)

Energy Technology Data Exchange (ETDEWEB)

Erik, N. Yalcin; Sancar, S. [Cumhuriyet University, Department of Geological Engineering, Sivas (Turkey)

2010-09-01

This study provides coal-quality, organic-petrographic and organic-geochemical data on Tertiary subbituminous coal of the Hafik area, northwestern part of the Sivas Basin, Turkey. Coal-petrological studies along with proximate and ultimate analyses were undertaken to determine the organic-petrographic characteristics of the Hafik coals. Huminite reflectances were found to be between 0.38 and 0.48% (corresponding to an organic-material-rich and coal layers), values characteristic of low maturity. This parameter shows a good correlation with calorific values (average 21,060 kJ/kg) and average T{sub max} (422 C) mineral-matter diagenesis, indicating immaturity. The studied coals and organic material underwent only low-grade transformation, a consequence of low lithostatic pressure. Therefore, the Hafik coals are actually subbituminous in rank. Rock-Eval analysis results show types II/III and III kerogens. The organic fraction of the coals is mostly comprised of humic-group macerals (gelinites), with small percentages derived from the inertinite and liptinite groups. In this study, organic-petrographic, organic-geochemical and coal quality data were compared. The Hafik deposit is a high-ash, high-sulfur coal. The mineral matter of the coals is comprised mainly of calcite and clay minerals. (author)

Cretaceous rocks of the Western Interior basin

International Nuclear Information System (INIS)

Molenaar, C.M.; Rice, D.D.

1988-01-01

The Cretaceous rocks of the conterminous United States are discussed in this chapter. Depositional facies and lithology are reviewed along with economic resources. The economic resources include coal, hydrocarbons, and uranium

RELIABILITY OF TRANSPORTATION SYSTEMS OF ROCK HAPS

Directory of Open Access Journals (Sweden)

A. Stepanov

2009-01-01

Full Text Available The ways of increasing of exploitation reliability of dump trucks with the aim of increasing of effectiveness of exploitation of transportation systems of rock heaps at coal mines.

Acoustic emission measurements in petroleum-related rock mechanics

Energy Technology Data Exchange (ETDEWEB)

Unander, Tor Erling

2002-07-01

Acoustic emission activity in rock has usually been studied in crystalline rock, which reflects that rock mechanics has also mostly been occupied with such rocks in relations to seismology, mining and tunneling. On the other hand, petroleum-related rock mechanics focuses on the behaviour of sedimentary rock. Thus, this thesis presents a general study of acoustic emission activity in sedimentary rock, primarily in sandstone. Chalk, limestone and shale have also been tested, but to much less degree because the AE activity in these materials is low. To simplify the study, pore fluids have not been used. The advent of the personal computer and computerized measuring equipment have made possible new methods both for measuring and analysing acoustic emissions. Consequently, a majority of this work is devoted to the development and implementation of new analysis techniques. A broad range of topics are treated: (1) Quantification of the AE activity level, assuming that the event rate best represents the activity. An algorithm for estimating the event rate and a methodology for objectively describing special changes in the activity e.g., onset determination, are presented. (2) Analysis of AE waveform data. A new method for determining the source energy of an AE event is presented, and it is shown how seismic source theory can be used to analyze even intermediate quality data. Based on these techniques, it is shown that a major part of the measured AE activity originates from a region close to the sensor, not necessarily representing the entire sample. (3) An improved procedure for estimating source locations is presented. The main benefit is a procedure that better handles arrival time data with large errors. Statistical simulations are used to quantify the uncertainties in the locations. The analysis techniques are developed with the application to sedimentary rock in mind, and in two articles, the techniques are used in the study of such materials. The work in the first

Designing optimum diameter of skip shafts in mines with inclined or steep coal seams

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1981-07-01

This paper discusses methods of increasing depth of operating shaft mines considering optimization of hoisting systems. The following solutions are analyzed: removing mined rock material to the surface, to operating horizon, to the deepest horizon, removing rock to the deepest horizon by enlarging a large diameter borehole. It is suggested that removing rock material to the surface is most economical. This solution is sometimes difficult to implement due to design of mine shafts. If a shaft is equipped with two pairs of skips, or with a pair of skips and two independent skips, one skip or a pair of skips can be removed to form free space for buckets used to hoist mined rock and coal. The bucket moves along rope shaft guides. Analysis of the optimum hoisting systems in shaft mines for coal mines with the following design capacity is carried out: 0.9, 1.2, 1.5 and 1.8 Mmt a year. The following depth of working horizons is evaluated: 600, 800, 1000, 1200, 1400 and 1600 m. It is assumed that coal and rock are hoisted separately. Advance rate ranges from 10 to 50 m/month. The results of analysis are shown in two tables. It is suggested that from the point of view of increasing depth of active mine shafts the following solutions are optimum: 7 m shaft with a system of three independently moving skips (two for coal, one for rock material), and 8 m shaft equipped with a pair of skips and two independent skips (one of the independently moving skips is used for rock hoisting). 4 refs.

Intrinsic reaction kinetics of coal char combustion by direct measurement of ignition temperature

International Nuclear Information System (INIS)

Kim, Ryang-Gyoon; Jeon, Chung-Hwan

2014-01-01

A wire heating reactor that can use a synchronized experimental method was developed to obtain the intrinsic kinetics of large coal char particles ranging in size from 0.4 to 1 mm. This synchronization system consists of three parts: a thermocouple wire for both heating and direct measurement of the particle temperature, a photodetector sensor for determining ignition/burnout points by measuring the intensity of luminous emission from burning particles, and a high-speed camera–long-distance microscope for observing and recording the movement of luminous zone directly. Coal char ignition was found to begin at a spot on the particle's external surface and then moved across the entire particle. Moreover, the ignition point determined according to the minimum of dT/dt is a spot point and not a full growth point. The ignition temperature of the spot point rises as the particle diameter increases. A spot ignition model, which describes the ignition in terms of the internal conduction and external/internal oxygen diffusion, was then developed to evaluate the intrinsic kinetics and predict the ignition temperature of the coal char. Internal conduction was found to be important in large coal char particles because its effect becomes greater than that of oxygen diffusion as the particle diameter increases. In addition, the intrinsic kinetics of coal char obtained from the spot ignition model for two types of coal does not differ significantly from the results of previous investigators. -- Highlights: • A novel technique was used to measure the coal char particle temperature. • The ignition point determined from a dT/dt minimum is a spot ignition point. • A spot ignition model was suggested to analyze the intrinsic reaction kinetics of coal char. • Internal conduction has to be considered in order to evaluate the intrinsic kinetics for larger particle (above 1 mm)

Critical Damage Analysis of WC-Co Tip of Conical Pick due to Coal Excavation in Mines

Directory of Open Access Journals (Sweden)

Saurabh Dewangan

2015-01-01

Full Text Available WC-Co based tools are widely used in the field of coal and rock excavation because of their unique combination of strength, hardness, and resistance to abrasive wear. Conical pick is one of the coal cutting tools. The tip of the pick is made of WC-Co material. As coal and rock are heterogeneous elements, they pose various constraints during excavation. As a result the tools wear out during the process. Other parameters like cutting techniques, tool orientation, and environmental conditions also affect the tool significantly. The wearing phenomenon greatly reduces the service life of the tools and thereby cuts down the production rate. To prevent such wearing process, it is important to investigate the different wear mechanisms in WC-Co. Simultaneously, there has to be an ongoing endeavour for the development of better quality WC-Co. This paper focuses on different wear mechanisms in a conical pick which has been used in a continuous miner machine for coal cutting. The worn out surface has been observed by using FE-SEM (field emission scanning electron microscopy and EDS (energy dispersive X-ray spectroscopy. The mechanisms, namely, coal/rock intermixing, cracking and crushing of WC grains, and adhesion of rock particles, have been predominantly investigated in this study. A little indication of corrosive decay in the WC grain has also been reported. The EDS has detected material concentration in a selected area or point of the worn-out surface. The spectrograph confirms the presence of coal/rock materials. Elements such as W, C, Ca, K, O, and Co have been mainly found in different concentrations at different positions.

Cataclastic effects in rock salt laboratory and in situ measurements

International Nuclear Information System (INIS)

Gramberg, J.; Roest, J.P.A.

1984-01-01

The aim of the research is the determination of eventual cataclastic effects in environmental rock salt of a heated part of a vertical deep test bore hole, a model for HLW disposal. Known cataclastic systems from hard rock mining and rock salt mines will form the starting point for the explanation of convergence of underground cavity walls. In rock salt, however, different elements seem to prevail: crystal plasticity and micro-cataclasis. The environmental measurements at the deep bore hole have to be carried out from a distance. To this end the acoustic micro-seismic method will be a suitable one. The appropriate equipment for micro-seismic cross hole measurement is designed, constructed and tested in the laboratory as well as underground. Acoustic velocity data form a crucial point. A micro-seismic acoustic P-wave model, adapted to the process of structural changes, is developed. P-wave velocity measurements in rock salt cubes in the laboratory are described. An underground cross hole measurement in the wall of a gallery with semi-circular section is treated and analysed. A conclusion was that, in this case, no macro-cataclasis (systematic large fractures) will be involved in the process of gallery convergence, but that the mechanism proved to be a combination of crystal plasticity and micro-cataclasis. The same mechanism might be expected to be present in the environmental rock salt of the HLW-disposal deep bore hole. As a result this environmental rock salt might be expected to be impermeable. A plan for the application of the developed equipment during the heating test on the ECN-deep-bore-hole is shown. A theory on ''disking'' or ''rim cracks'' is presented in an annex

Continuous dust monitoring in headings in underground coal mines

Directory of Open Access Journals (Sweden)

Kazimierz Lebecki

2016-01-01

Full Text Available The article presents hazardous conditions of airborne dust based on the results of measurements of dust concentration taken at work-places at a underground rock-coal face drilled by a heading machine with combined ventilation (suction and forced ventilation with dust collector. The measurements were taken using three methods in order to examine and assess the actual conditions within the excavation subject to the study. The measurement results and conclusions show major difficulties in achieving MAC levels. Research conclusions indicate the low efficiency of collective and personal measures applied to protect against dust harmful to health as well as the need to improve them.

Rock stress measurements using the LUT-Gauge overcoring method

International Nuclear Information System (INIS)

Leijon, B.

1988-04-01

With overcoring techniques, rock stresses are determined indirectly from measurements of the dimensional changes of a borehole, occurring when the rock volume surrounding the hole is isolated from the stresses in the host rock. This thesis describes the development and application of an overcoring technique. The key-component of the instrumentation that has been developed is a triaxial borehole strain cell, referred to as the LUT-Gauge. Laboratory tests were conducted to evaluate the performance of the instrumentation. Special emphasis was given to determining temperature sensitivity of the measuring system since this was identified as a potential source of measurement error. Results indicated good instrument reliability and that the measurement error due to temperature variations typically experienced under field conditions is ± 1 MPa or less. The technique was also evaluated by a series of field tests. Comparison of the results obtained by the different methods showed satisfactory agreement. Analysis of the comprehensive field data collected showed that the confidence that can be attached to an overcoring test is largely governed by the mechanical characteristics of the overcored specimen. Expressed as the standard deviation of the mean stress magnitude, the scatter obtained from repeated testing within a borehole section of about 10 m in length, is found to be ± 4 MPa or less. Rock engineering investigations typically refer to a scale of hundreds of metres or more. This study has demonstrated the existence of significant variations of the stress field on this scale. These variations thus impose difficulties in the application of stress data to the analysis of problems in rock engineering, since the pointwise results obtained from stress measurements cannot be extrapolated with good confidence. (30 refs.) (author)

Scale of seismic and rock burst hazard in the Silesian companies in Poland

Energy Technology Data Exchange (ETDEWEB)

Renata Patynska; Jozef Kabiesz [Central Mining Institute, Katowice (Poland)

2009-09-15

Presently the seismic and rock burst hazard appears still to be important in most of hard coal mines in Poland. Recently, there was a significant increase of seismic activity of the Silesian rock massive, when compared with the previous years. In the period 1999-2008 the hard coal mines experienced 34 rock bursts. The causes of rockburst occurrence are presented based on the analysis of the rockbursts occurring in the Polish hard coal mines. The scale of the rockburst hazard has been characterized with respect to the mining and geological conditions of the existing exploitation. Of the factors influencing the state of rockburst hazard, the most essential one is considered the depth interval ranging from 600 m to 900 m. The basic factors that promote the rockburst occurrence are as follows: seismogenic strata, edges and remnants, goaf, faults, pillars and excessive paneling. 5 refs., 3 figs., 2 tabs.

Prevention of rock bursts at the West mine; Gebirgsschlagverhuetung auf dem Bergwerk West

Energy Technology Data Exchange (ETDEWEB)

Braick, Helmut; Bartel, Ralf [RAG Deutsche Steinkohle AG, Bergwerk West, Kamp-Lintfort (Germany); Baltz, Ruediger [DMT GmbH und Co. KG, Essen (Germany). Fachsstelle fuer Gebirgsschlagverhuetung

2011-08-15

An unusually comprehensive stress-relief measure to eliminate a detected rock burst hazard in the Girondelle seam at the West mine clearly shows that an increase in the stress-relief cases must also be anticipated in the seam horizons, which were regarded as relatively uncritical in the recent past. An overall depth trend is recognisable in the Ruhr district. The combination of greater depth and higher strength of the enclosing rock and the more extensive pressure-increasing factors such as working boundaries and residual pillars clearly increases the probability of critical rock stresses in the vicinity of mine workings. The system applied in the German coal mining industry to detect and eliminate critical rock stresses ensures with a correct expert procedure that rock bursts do not occur and protection of personnel can thus be ensured despite extremely difficult conditions as in the stress-relief case in the Girondelle seam. (orig.)

Open cast blasting of coal in Australia; Goshu rotenbori tanko kengakuki

Energy Technology Data Exchange (ETDEWEB)

Hashizume, K. [Nippon Kayaku Co. Ltd., Tokyo (Japan)

1997-06-30

Introduced in this report are blastings performed for surface coal mining in the southeastern part of Australia. The Liddell coal mine began mining in 1990. This mine enjoys an annual raw coal yield of 2-million ton, removing approximately 11-million m{sup 3} of rocks consuming 5000 ton of anfo and emulsion explosives. The explosives are carried by a pump truck to the site where mixing is carried out, and non-electrical primers are used for detonation. The other mine described here is the Camberwell mine that yields 3.5-million ton of raw coal annually. For each blasting, 100-200 ton of explosive is consumed. A pump truck reciprocates between the material plant near the mine and the location of blasting, and charges the explosive directly. One of the anfo, emulsion, and heavy-anfo explosives is chosen, dependent upon conditions such as rock hardness. Also mentioned in this report are general blasting specifications relating to blasting at these two mines

Study of Experiment on Rock-like Material Consist of fly-ash, Cement and Mortar

Science.gov (United States)

Nan, Qin; Hongwei, Wang; Yongyan, Wang

2018-03-01

Study the uniaxial compression test of rock-like material consist of coal ash, cement and mortar by changing the sand cement ratio, replace of fine coal, grain diameter, water-binder ratio and height-diameter ratio. We get the law of four factors above to rock-like material’s uniaxial compression characteristics and the quantitative relation. The effect law can be sum up as below: sample’s uniaxial compressive strength and elasticity modulus tend to decrease with the increase of sand cement ratio, replace of fine coal and water-binder ratio, and it satisfies with power function relation. With high ratio increases gradually, the uniaxial compressive strength and elastic modulus is lower, and presents the inverse function curve; Specimen tensile strength decreases gradually with the increase of fly ash. By contrast, uniaxial compression failure phenomenon is consistent with the real rock common failure pattern.

Attempt of groundwater dating using the drilled rock core. 1. Development of the rock sampling method for measurement of noble gases dissolved in interstitial water in rock

International Nuclear Information System (INIS)

Mahara, Yasunori

2002-01-01

Groundwater dating in low permeable rock is very difficult and impracticable, because we take a very long time to collect groundwater sample in a borehole and have to invest much fund in production of the in-situ groundwater sampler and in operation of it. If we can directly measure noble gases dissolved in interstitial groundwater in rock core, we have a big merit to estimate groundwater resident time easy. In this study, we designed and produced a high vacuum container to let dissolved noble gases diffuse until reaching in equilibrium, and we made a handling manual of the rock core into the container and a procedure to vacuum out air from the sealed container. We compared data sets of noble gas concentration obtained from rock cores and groundwater sample collected from boreholes in-situ. The measured rocks are pumice-tuff rock, mud rock and hornfels, which have their permeabilities of 10 -6 cm/s, 10 -9 cm/s and 10 -11 cm/s, respectively. Consequently, we evaluated the rock core method is better than the in-situ groundwater sampling method for low permeable rock. (author)

Prediction of mining conditions from bore core information: rock mechanics investigations in the Whybrow Seam at Wambo Colliery

Energy Technology Data Exchange (ETDEWEB)

Richmond, A.; Levers, R.; Smith, K.

1979-12-01

Rock mechanics investigations were conducted at Wambo Colliery as part of the series designed to study the stability of mining structures and obtain geomechanical properties. The roof and floor were drilled in order to obtain core for rock testing and samples of coal were collected to measure the coal properties. A successful overcoring of a CSIR strain cell was achieved to determine the absolute stress field. The core which was recovered was logged prior to laboratory testing to determine a C index (modified RQD index based on core fragmentation). This was used to estimate the in-situ strata properties from the laboratory results. The roof material was found to consist predominantly of a competent laminite. The Whybrow seam above the Cow Manure band had an average uniaxial strength of 26 MPa. The Cow Manure band was extremely weak with a strength of 1 MPa, while the coal below this band was much weaker than the upper section coal with a strength of 7 MPa. The floor strata was made up of competent carbonaceous siltstone and alternate bands of shale and sandstone. Finite element analyses indicate very stable roof, floor and rib, corresponding closely to the in-situ conditions.

Geology of Santa Rita Coal Basin, Rio Grande do Sul, Brazil

Energy Technology Data Exchange (ETDEWEB)

Correa da Silva, Z.C.; Bortoluzzi, C.A.; Cazzulo-Klepzig, M.; Dias-Fabricio, M.E.; Guerra-Sommer, M.; Marques-Toigo, M.; Paim, P.S.G.; Piccoli, A.E.M.; Silva Filho, B.C.

1984-04-01

Data on the sedimentology, stratigraphy, palynology, coal petrography and geochemistry of the Santa Rita Coal Basin, Rio Grande do Sul, Brazil, are presented. The investigations were carried out on samples obtained from drill cores of the sedimentary rocks of Tubarao Supergroup, Lower Permian of Parana Basin. (25 refs.)

PROBLEMS AND METHODOLOGY OF THE PETROLOGIC ANALYSIS OF COAL FACIES.

Science.gov (United States)

Chao, Edward C.T.

1983-01-01

This condensed synthesis gives a broad outline of the methodology of coal facies analysis, procedures for constructing sedimentation and geochemical formation curves, and micro- and macrostratigraphic analysis. The hypothetical coal bed profile has a 3-fold cycle of material characteristics. Based on studies of other similar profiles of the same coal bed, and on field studies of the sedimentary rock types and their facies interpretation, one can assume that the 3-fold subdivision is of regional significance.

Temporal measurements and kinetics of selenium release during coal combustion and gasification in a fluidized bed

International Nuclear Information System (INIS)

Shen, Fenghua; Liu, Jing; Zhang, Zhen; Yang, Yingju

2016-01-01

Highlights: • The temporal release of Se from coal combustion and gasification was measured. • Kinetic laws for Se release from coal combustion and gasification were determined. • The influences of temperature and chemical composition of flue gas were clarified. • The interactions of Se species with mineral affect the release kinetics of Se. - Abstract: The temporal release of selenium from coal during combustion and gasification in a fluidized bed was measured in situ by an on-line analysis system of trace elements in flue gas. The on-line analysis system is based on an inductively coupled plasma optical emission spectroscopy (ICP-OES), and can measure concentrations of trace elements in flue gas quantitatively and continuously. The results of on-line analysis suggest that the concentration of selenium in flue gas during coal gasification is higher than that during coal combustion. Based on the results of on-line analysis, a second-order kinetic law r(x) = 0.94e −26.58/RT (−0.56 x 2 −0.51 x + 1.05) was determined for selenium release during coal combustion, and r(x) = 11.96e −45.03/RT (−0.53 x 2 −0.56 x + 1.09) for selenium release during coal gasification. These two kinetic laws can predict respectively the temporal release of selenium during coal combustion and gasification with an acceptable accuracy. Thermodynamic calculations were conducted to predict selenium species during coal combustion and gasification. The speciation of selenium in flue gas during coal combustion differs from that during coal gasification, indicating that selenium volatilization is different. The gaseous selenium species can react with CaO during coal combustion, but it is not likely to interact with mineral during coal gasification.

Diagenesis of diatomite from the Kolubara Coal Basin, Barosevac, Serbia

Energy Technology Data Exchange (ETDEWEB)

Obradovic, J; Hein, J R; Djurdjevic, J [University of Belgrade, Belgrade (Yugoslavia). Faculty of Mining and Geology

1994-09-01

Diatomite associated with the Kolubara Coal Basin was studied to better understand early stage silica diagenesis of shallow water deposits. The Kolubara Basin consists of Neogene siliciclastic rocks, diatomite, marlstone and rare carbonates. Palaeozoic metamorphic and Mesozoic sedimentary and igneous basement rocks are transgressively overlain by Upper Miocene sandstone, siltstone, shale and mudstone. This Upper Miocene section is transgressively overlain by the Pontian section, which contains diatomite and coal beds. White and grey diatomite form beds 0.7-2.2 m thick that are continuous over an area of about 2 km[sup 2]. Siliceous rocks vary in composition from diatomite (81-89% SiO[sub 2]) to diatom-bearing shale (58-60% SiO[sub 2]). Siliceous deposits are laminated in places, with the laminae defined by variations in clay minerals, organic matter and diatoms. Diatomite shows only incipient diagenesis characterized by the fragmentation of diatom frustules, the minor to moderate corrosion of frustules and the formation of minor amounts of opal-A (X-ray amorphous inorganic opal) cement. The low degree of diagenesis results from the young age of the deposits, low burial temperatures and possibly also from the presence of abundant organic matter and the dissolution of kaolinite. The presence of only weak diagenesis is also reflected by the characteristically poor consolidation of the rocks and low rank of the associated coal.

Convergence measurements in a 300 m deep borehole in rock salt

International Nuclear Information System (INIS)

Heijdra, J.J.; Prij, J.

1992-05-01

An evaluation is presented of convergence measurements in a 300 m deep borehole in rock salt. The measured convergence is compared to the normalized convergence based on an analytical solution. Measurements endorse the assumptions on which the analytical solution has been based. With the aid of this analytical solution the ambient rock pressure at the locations of the measurements is determined. The derived pressures and the corresponding depth below the 750 m level are 20.3 MPa at -300 m, 15.4 MPa at -200 m and 13.3 MPa at -100 m. The measurements, normalized in order to account for the influence of the diameter and for the difference in depth, show good correspondence with former measurements on selected cavities in rock salt. (author). 6 refs.; 17 figs.; 3 tabs

Investigations of some rock stress measuring techniques and the stress field in Norway

Energy Technology Data Exchange (ETDEWEB)

Hanssen, Tor Harald

1998-12-31

Rock stresses are important to the safe construction and operation of all man-made structures in rock, whether In mining, civil or petroleum engineering. The crucial issue is their relative magnitude and orientation. This thesis develops equipment and methods for further rock stress assessment and reevaluates existing overcoring rock stress measurements, and relates this information to the present geological setting. Both laboratory work and field work are involved. In the field, rock stresses are measured by the overcoring and the hydraulic fracturing technique. An observation technique for assessing likely high stresses is developed. The field data refer to several hydropower projects and to some offshore hydrocarbon fields. The principal sections are: (1) Tectonic setting in the western Fennoscandia, (2) Triaxial rock stress measurements by overcoring using the NTH cell (a strain gauge cell developed at the Norwegian technical university in Trondheim and based on the CSIR cell of the South African Council for Scientific and Industrial Research), (3) Laboratory testing of the NTH cell, (4) Quality ranking of stresses measured by the NTH cell, (4) Recalculated rock stresses and implications to the regional stress field, (5) Hydraulic fracturing stress measurements. 113 refs., 98 figs., 62 tabs.

Investigations of some rock stress measuring techniques and the stress field in Norway

Energy Technology Data Exchange (ETDEWEB)

Hanssen, Tor Harald

1997-12-31

Rock stresses are important to the safe construction and operation of all man-made structures in rock, whether In mining, civil or petroleum engineering. The crucial issue is their relative magnitude and orientation. This thesis develops equipment and methods for further rock stress assessment and reevaluates existing overcoring rock stress measurements, and relates this information to the present geological setting. Both laboratory work and field work are involved. In the field, rock stresses are measured by the overcoring and the hydraulic fracturing technique. An observation technique for assessing likely high stresses is developed. The field data refer to several hydropower projects and to some offshore hydrocarbon fields. The principal sections are: (1) Tectonic setting in the western Fennoscandia, (2) Triaxial rock stress measurements by overcoring using the NTH cell (a strain gauge cell developed at the Norwegian technical university in Trondheim and based on the CSIR cell of the South African Council for Scientific and Industrial Research), (3) Laboratory testing of the NTH cell, (4) Quality ranking of stresses measured by the NTH cell, (4) Recalculated rock stresses and implications to the regional stress field, (5) Hydraulic fracturing stress measurements. 113 refs., 98 figs., 62 tabs.

Final Report: Geothermal dual acoustic tool for measurement of rock stress

Energy Technology Data Exchange (ETDEWEB)

Normann, Randy A. [Perma Works LLC, Pattonville, TX (United States)

2014-12-01

This paper outlines the technology need for a rock formation stress measurement in future EGS wells. This paper reports on the results of work undertaken under a Phase I, DOE/SBIR on the feasibility to build an acoustic well logging tool for measuring rock formation stress.

Final Report. Geothermal Dual Acoustic Tool for Measurement of Rock Stress

Energy Technology Data Exchange (ETDEWEB)

Normann, Randy A [Perma Works LLC, Pattonville, TX (United States)

2014-12-01

This paper outlines the technology need for a rock formation stress measurement in future EGS wells. This paper reports on the results of work undertaken under a Phase I, DOE/SBIR on the feasibility to build an acoustic well logging tool for measuring rock formation stress.

Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

Science.gov (United States)

Borowski, Marek; Kuczera, Zbigniew

2018-03-01

Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage) could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in the air; location

Comparison of Methane Control Methods in Polish and Vietnamese Coal Mines

Directory of Open Access Journals (Sweden)

Borowski Marek

2018-01-01

Full Text Available Methane hazard often occurs in hard coal mines and causes very serious accidents and can be the reason of methane or methane and coal dust explosions. History of coal mining shows that methane released from the rock mass to the longwall area was responsible for numerous mining disasters. The main source of methane are coal deposits because it is autochthonous gas and is closely related with carbonification and forming of coal deposits. Degree of methane saturation in coal deposits depends on numerous factors; mainly on presence or lack of insulating layers in cover deposit that allow or do not on degasification and easily methane outflow into surroundings. Hence in coal mining there are coal deposits that contain only low degree of methane saturation in places where is lack of insulating layers till high in methane coal deposits occurring in insulating claystones or in shales. Conducting mining works in coal deposits of high methane hazard without using of special measures to combat (ventilation, methane drainage could be impossible. Control of methane hazard depends also on other co-occuring natural dangers for which used preventive actions eliminate methane hazard. Safety in mines excavating coal deposits saturated with methane depends on the correct estimation of methane hazard, drawn up forecasts, conducted observations, hazard control as well as undertaken prevention measures. Methane risk prevention includes identification and control methods of methane hazards as well as means of combating the explosive accumulation of methane in longwall workings. The main preventive actions in underground coal mines are: effective ventilation that prevents forming of methane fuses or placed methane accumulation in headings ventilated by airflow created by main fans and in headings with auxiliary ventilation, methane drainage using drain holes that are drilled from underground headings or from the surface, methanometry control of methane concentration in

Comparison of laboratory, in situ, and rock mass measurements of the hydraulic conductivity of metamorphic rock at the Savannah River Plant near Aiken, South Carolina

International Nuclear Information System (INIS)

Marine, I.W.

1980-01-01

In situ testing of exploratory wells in metamorphic rock indicates that two types of fracturing occur in the rock mass. Rock containing small openings that permit only extremely slow movement of water is termed virtually impermeable rock. Rock containing openings of sufficient size to permit transmission of water at a significantly faster rate is termed hydraulically transmissive rock. Laboratory methods are unsuitable for measuring hydraulic conductivity in hydraulically transmissive rock; however, for the virtually impermeable rock, values comparable to the in situ tests are obtained. The hydraulic conductivity of the rock mass over a large region is calculated by using the hydraulic gradient, porosity, and regional velocity. This velocity is determined by dividing the inferred travel distance by the age of water which is determined by the helium content of the water. This rock mass hydraulic conductivity value is between the values measured for the two types of fractures, but is closer to the measured value for the virtually impermeable rock. This relationship is attributed to the control of the regional flow rate by the virtually impermeable rock where the discrete fractures do not form a continuous open connection through the entire rock mass. Thus, laboratory methods of measuring permeability in metamorphic rock are of value if they are properly applied

Influence of a Large Pillar on the Optimum Roadway Position in an Extremely Close Coal Seam

Directory of Open Access Journals (Sweden)

Li Yang

2016-01-01

Full Text Available Based on the mining practice in an extremely close coal seam, theoretical analysis was conducted on the vertical stress distribution of the floor strata under a large coal pillar. The vertical stress distribution regulation of a No. 5 coal seam was revealed. To obtain the optimum position of the roadway that bears the supporting pressure of a large coal pillar, numerical modeling was applied to analyze the relation among the stress distribution of the roadway surrounding the rock that bears the supporting pressure of a large coal pillar, the plastic zone distribution of the roadway surrounding the rock, the surrounding rock deformation, and the roadway layout position. The theoretical calculation results of the stress value, stress variation rate, and influencing range of the stress influencing angle showed that the reasonable malposition of the No. 5 coal seam roadway was an inner malposition of 4 m. The mining practice showed the following: the layout of No. 25301 panel belt roadway at the position of the inner malposition of 4 m was reasonable, the roadway support performance was favourable without deformation, and ground pressure was not obvious. The research achievement of this study is the provision of a reference for roadway layouts under similar conditions.

Study on the Effect of Frequency on Conductivity of Underground Strata in Coal Mine Through-the-earth Wireless Communication

OpenAIRE

Jinyi TAO; Yuchen ZHANG

2014-01-01

The relationship of conductivity and the frequency, which is of decisive significance in through-the-earth wireless communication in coal mine, is closely related to the options of frequency range in coal mine wireless communication. When through-the-earth wireless communication is applied, the electromagnetic waves need to spread in the semi-conductive medium rocks. The main factors affecting the electromagnetic wave propagation in rocks is the rock strata electromagnetic parameters. These p...

Coal cleaning: A viable strategy for reduced carbon emissions and improved environment in China?

OpenAIRE

Glomsrød, Solveig; Taoyuan, Wei

2003-01-01

Abstract: China is a dominant energy consumer in a global context and current energy forecasts emphasise that China’s future energy consumption also will rely heavily on coal. The coal use is the major source of the greenhouse gas CO2 and particles causing serious health damage. This paper looks into the question if coal washing might work as low cost strategy for both CO2 and particle emission reductions. Coal washing removes dirt and rock from raw coal, resulting in a coal pr...

Measurements of noise from rotary coal unloading operations

International Nuclear Information System (INIS)

Adams, T.S.; Bilello, M.A.

1991-01-01

In the licensing effort for a coal-fired power plant in the northeast United States, noise related to delivery and unloading of coal by train was identified as a significant concern to the nearby community. Specific issues included locomotive noise, the banging noises caused by railcar couplings during the start and stop cycles of the unloading operation, wheel squeal in the curves of the rail loop, and rotary coal unloader noises. This paper reports that a literature review provided adequate information on idling locomotive noise but very little on the other noise sources. Coupling impact noise was well documented for railcars actually being coupled at various speeds but not for coupled trains during start and stop operations. Wheel squeal was well documented by subway trains travelling at normal speeds, but nothing could be found for wheel squeal during very slow train movement as occurs during unloading. Similarly, adequate information was available for unenclosed rotary unloaders but not for enclosed unloaders. Consequently, actual noise measurements of a similar enclosed facility, and the associated train movements, were undertaken to obtain data more directly applicable to the planned facility

Engineering and Design: Characterization and Measurement of Discontinuities in Rock Slopes

National Research Council Canada - National Science Library

1983-01-01

This ETL provides guidance for characterizing and measuring rock discontinuities on natural slopes or slopes constructed in rock above reservoirs, darn abutments, or other types of constructed slopes...

Analysis on the Initial Cracking Parameters of Cross-Measure Hydraulic Fracture in Underground Coal Mines

Directory of Open Access Journals (Sweden)

Yiyu Lu

2015-07-01

Full Text Available Initial cracking pressure and locations are important parameters in conducting cross-measure hydraulic fracturing to enhance coal seam permeability in underground coalmines, which are significantly influenced by in-situ stress and occurrence of coal seam. In this study, stress state around cross-measure fracturing boreholes was analyzed using in-situ stress coordinate transformation, then a mathematical model was developed to evaluate initial cracking parameters of borehole assuming the maximum tensile stress criterion. Subsequently, the influences of in-situ stress and occurrence of coal seams on initial cracking pressure and locations in underground coalmines were analyzed using the proposed model. Finally, the proposed model was verified with field test data. The results suggest that the initial cracking pressure increases with the depth cover and coal seam dip angle. However, it decreases with the increase in azimuth of major principle stress. The results also indicate that the initial cracking locations concentrated in the second and fourth quadrant in polar coordinate, and shifted direction to the strike of coal seam as coal seam dip angle and azimuth of maximum principle stress increase. Field investigation revealed consistent rule with the developed model that the initial cracking pressure increases with the coal seam dip angle. Therefore, the proposed mathematical model provides theoretical insight to analyze the initial cracking parameters during cross-measure hydraulic fracturing for underground coalmines.

Coal depositional models in some tertiary and cretaceous coal fields in the US western interior

Energy Technology Data Exchange (ETDEWEB)

Flores, R M

1979-12-01

Detailed stratigraphic and sedimentological studies of the Tertiary Tongue River Member of the Fort Union Formation in the Powder River Basin, Wyoming, and the Cretaceous Blackhawk Formation and Star Point Sandstone in the Wasatch Plateau, Utah, indicate that the depositional environments of coal played a major role in controlling coal thickness, lateral continuity, potential minability, and type of floor and roof rocks. The potentially minable, thick coal beds of the Tongue River Member were primarily formed in long-lived floodbasin backswamps of upper alluvial plain environment. Avulsion of meandering fluvial channels contributed to the erratic lateral extent of coals in this environment. Laterally extensive coals formed in floodbasin backswamps of a lower alluvial plain environment; however, interruption by overbank and crevasse-splay sedimentation produced highly split and merging coal beds. Lacustrine sedimentation common to the lower alluvial plain, similar to the lake-covered lower alluvial valley of the Atchafalaya River Basin, is related to a high-constructive delta. In contrast to these alluvial coals are the deltaic coal deposits of the Blackhawk Formation. The formation consists of three coal populations: upper delta plain, lower delta plain, and back-barrier. Coals of the lower delta plain are thick and laterally extensive, in contrast to those of the upper delta plain and back-barrier, which contain abundant, very thin and laterally discontinuous carbonaceous shale partings. The reworking of the delta-front sediments of the Star Point Sandstone suggests that the Blackhawk-Star Point delta was a high-destructive system. 1 figure, 1 table.

Ge distribution in the Wulantuga high-germanium coal deposit in the Shengli coalfield, Inner Mongolia, northeastern China

Energy Technology Data Exchange (ETDEWEB)

Du, Gang [Key Laboratory of Marginal Sea Geology, Chinese Academy of Sciences (China)]|[Coal Geology Bureau of Inner Mongolia, Hohhot, 010051 (China); Zhuang, Xinguo [Institute of Sedimentary Basin and Mineral, Faculty of Earth Resources, China University of Geosciences, Hubei, 430074 (China)]|[State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Hubei, 430074 (China); Querol, Xavier; Izquierdo, Maria; Alastuey, Andres; Moreno, Teresa; Font, Oriol [Institute of Earth Science ' Jaume Almera' , CSIC, C/ LLuis Sole Sabaris s/n, 08028 Barcelona (Spain)

2009-03-01

The geological and geochemical controls of the Ge distribution in the Cretaceous Wulantuga high-Germanium coal deposit in the Shengli coal field, Inner Mongolia are investigated. This paper focuses mainly on the spatial distribution of the Ge contents in coal. The high-Ge coals mainly occur in three splits of the 6 coal in the southwestern part of the Shengli coal field. Mean germanium contents in the coal range from 32 to 820 {mu}g/g, with a mean value of 137 {mu}g/g, on a bulk coal basis (mean of 939 coal samples from 75 boreholes in the 6 coal seam) in an area of 2.2 km{sup 2}. The highest Ge content occurs SW of 6 coal seam, close to the margins of the coal basin, decreasing with a fan-shaped trend towards NW, the direction of the coal basin. There is an negative correlation between the mean Ge content and the thickness of the coal seam. Different distribution patterns of Ge content were found in vertical profiles. High Ge concentrations may occur in the middle parts of coal seams, at the bottom and/or the top of thick coal seams and inconspicuous variation. A major organic affinity was determined for Ge, with a special enriched in the banded bright and semibright coal. The high-Ge coals and the coalified wood in the sandstone overlaying the 6-1 coal highly enriched in Ge, As, Sb, W, Cs, Tl, Be, and Hg. The Late Jurassic silicified volcanic rocks in the NW of the Ge coal deposit relatively high enriched in Ge, Ga, Sb, As, Cs, Be, Ge and Hg. The correlation coefficients among the elements enriched showed marked variations at close sites in this deposit, suggesting a possible diagenetic origin of the geochemical anomaly. The main Ge anomaly was attributed to early Cretaceous hydrothermal fluids circulating through the fault systems and porous volcanic rocs, probably from the subjacent granitoid rocks. The fault systems, the porous coarse clastic rocks overlying coal seam and the lithotype of coal played an important role in the transport and trapping of Ge. A

Safety explosives in coal mining. Explosivos de seguridad en la mineria de carbon

Energy Technology Data Exchange (ETDEWEB)

(Union Espanola de Explosivos y Rio Blast, S.A., Madrid (Spain))

1990-06-01

The use of explosives in underground coal mining is essential for two reasons. The first is the highly resistant nature of the rock surrounding coal which requires explosives to remove it during development work. The second is that certain types of coal need to be blasted in order to achieve a higher output in coal winning operations. This article examines the characteristics, the types and the conditions under which safety or ion exchange explosives are used in underground coal mines where explosive atmospheres are sometimes encountered. 3 tabs. 2 pts.

Underground coal mining technology - the future

Energy Technology Data Exchange (ETDEWEB)

Lama, R P [Kembla Coal and Coke Pty Limited, Wollongong, NSW (Australia)

1989-01-01

Discusses development of underground coal mining in Australia in the last four decades. The following aspects are reviewed: technology for underground mining (longwall mining, unidirectional cutting, bidirectional cutting, operation of more than one shearer on a working face, optimum dimensions of longwall blocks), longwall productivity (productivity increase will depend on increasing the availability factor of equipment, reducing failures due to human errors, organizational models, improving on-site decision making, improving monitoring, maintenance, planning and scheduling, concept of 'Transparent Mine'), roadway development systems (types of heading machines, standard systems for mine drivage and roof bolting and their productivity), size of coal mines, man and material transport systems (20,000-30,000 t/d from a single longwall face, mine shafts with a diameter 9-10 m), mine layout design (layout of longwall blocks, main intakes and returns situated in rock layers), mine environmental systems (ventilation systems, gas control), management, training and interpersonal relationships. Future coal mines will be developed with an integral capacity of 8-10 Mt/a from a single longwall operation with main development arteries placed in rocks. Development of gate roadways will require novel solutions with continuous cutting, loading and bolting. Information technology, with the concept of 'transparent mine', will form the backbone of decision making.

Mechanical Properties and Acoustic Emission Properties of Rocks with Different Transverse Scales

OpenAIRE

Yan, Xi; Jun, Li; Gonghui, Liu; Xueli, Guo

2017-01-01

Since the stability of engineering rock masses has important practical significance to projects like mining, tunneling, and petroleum engineering, it is necessary to study mechanical properties and stability prediction methods for rocks, cementing materials that are composed of minerals in all shapes and sizes. Rocks will generate acoustic emission during damage failure processes, which is deemed as an effective means of monitoring the stability of coal rocks. In the meantime, actual mining a...

Crack identification and evolution law in the vibration failure process of loaded coal

Science.gov (United States)

Li, Chengwu; Ai, Dihao; Sun, Xiaoyuan; Xie, Beijing

2017-08-01

To study the characteristics of coal cracks produced in the vibration failure process, we set up a static load and static and dynamic combination load failure test simulation system, prepared with different particle size, formation pressure, and firmness coefficient coal samples. Through static load damage testing of coal samples and then dynamic load (vibration exciter) and static (jack) combination destructive testing, the crack images of coal samples under the load condition were obtained. Combined with digital image processing technology, an algorithm of crack identification with high precision and in real-time is proposed. With the crack features of the coal samples under different load conditions as the research object, we analyzed the distribution of cracks on the surface of the coal samples and the factors influencing crack evolution using the proposed algorithm and a high-resolution industrial camera. Experimental results showed that the major portion of the crack after excitation is located in the rear of the coal sample where the vibration exciter cannot act. Under the same disturbance conditions, crack size and particle size exhibit a positive correlation, while crack size and formation pressure exhibit a negative correlation. Soft coal is more likely to lead to crack evolution than hard coal, and more easily causes instability failure. The experimental results and crack identification algorithm provide a solid basis for the prevention and control of instability and failure of coal and rock mass, and they are helpful in improving the monitoring method of coal and rock dynamic disasters.

Mobilisation and attenuation of boron during coal mine rehabilitation, Wangaloa, New Zealand

International Nuclear Information System (INIS)

Craw, D.; Rufaut, C.G.; Haffert, L.; Todd, A.

2006-01-01

Environmental mobility and fate of boron has been traced from source to discharge waters through the rehabilitated Wangaloa coal mine in southern New Zealand. The boron is derived initially from coal, which has up to 450 mg/kg B. The coal also contains pyrite (2-5 wt.% S), which oxidizes to yield a low-pH environment (typical pH 2-5). Weathering of coal-bearing waste rock liberates B into rainwater that infiltrates into waste rock or evaporates to leave a gypsum crust enriched in B, possibly as boric acid or colemanite as inferred from geochemical modelling. Surface waters dissolve this evaporative material periodically, yielding total B concentrations up to 6 mg/L, at pH<4.5. Some of the available B is taken up by plants that have been established on the waste rock, resulting in foliage B concentrations of up to 230 mg/kg (dry weight). Partial attenuation of dissolved B by adsorption to iron oxyhydroxide occurs as groundwater passes through waste rock, but this is inhibited by adsorption competition with dissolved sulphate (up to 600 mg/L). Groundwater flows from the mine through a pit lake and wetland, with total dissolved B near 1 mg/kg after dilution and limited adsorption attenuation has occurred. Despite the widespread B mobility throughout the rehabilitated mine, there is little evidence of B toxicity in plants. The B concentrations in discharging waters are in the environmentally safe range for most aquatic organisms, being neither deficient in B as a micronutrient, nor boron-toxic. (author)

Determination of ash content of coal by mass absorption coefficient measurements at two X-ray energies

International Nuclear Information System (INIS)

Fookes, R.A.; Gravitis, V.L.; Watt, J.S.

1977-01-01

A method for determining the ash content of coal is proposed. It involves measurements proportional to mass absorption coefficients of coal at two X-ray energies. These measurements can be made using X-ray transmission or scatter techniques. Calculations based on transmission of narrow beams of X-rays have shown that ash can be determined to about 1wt%(1 sigma) in coal of widely varying ash content and composition. Experimentally, ash content was determined to 0.67wt% by transmission techniques and 1.0wt% by backscatter techniques in coal samples from the Bulli seam, NSW, Australia, having ash in the range 11-34wt%. For samples with a much wider range of coal composition (7-53wt% ash and 0-25wt% iron in the ash), ash content was determined by backscatter measurements to 1.62wt%. The method produced ash determinations at least as accurate as those produced by the established technique which compensates for variation in iron content of the ash by X-ray fluorescence analysis for iron. Compared with the established technique, it has the advantage of averaging analysis over much larger volumes of coal, but the disadvantage that much more precise measurements of X-ray intensities are required. (author)

Trace uranium analysis in Indian coal samples using the fission track technique

International Nuclear Information System (INIS)

Jojo, P.J.; Rawat, A.; Kumar, Ashavani; Prasad, Rajendra

1993-01-01

The ever-growing demand for energy has resulted in the extensive use of fossil fuels, especially coal, for power generation. Coal and its by-products often contain significant amounts of radionuclides, including uranium, which is the ultimate source of the radioactive gas Radon-222. The present study gives the concentration of uranium in coal samples of different collieries in India, collected from various thermal power plants in the state of Uttar Pradesh. The estimates were made using the fission track technique. Latent damage tracks were not found to be uniformly distributed but showed sun bursts and clusters. Non-uniform distributions of trace elements are a very common phenomenon in rocks. The levels of uranium in the coal samples were found to vary from 2.0 to 4.9 ppm in uniform distributions and from 21.3 to 41.0 ppm in non-uniform distributions. Measurements were also made on fly ash samples where the average uranium concentration was found to be 8.4 and 49.3 ppm in uniform and non-uniform distributions, respectively. (author)

A methodology for interpretation of overcoring stress measurements in anisotropic rock

International Nuclear Information System (INIS)

Hakala, M.; Sjoeberg, J.

2006-11-01

The in situ state of stress is an important parameter for the design of a repository for final disposal of spent nuclear fuel. This report presents work conducted to improve the quality of overcoring stress measurements, focused on the interpretation of overcoring rock stress measurements when accounting for possible anisotropic behavior of the rock. The work comprised: (i) development/upgrading of a computer code for calculating stresses from overcoring strains for anisotropic materials and for a general overcoring probe configuration (up to six strain rosettes with six gauges each), (ii) development of a computer code for determining elastic constants for transversely isotropic rocks from biaxial testing, and (iii) analysis of case studies of selected overcoring measurements in both isotropic and anisotropic rocks from the Posiva and SKB sites in Finland and Sweden, respectively. The work was principally limited to transversely isotropic materials, although the stress calculation code is applicable also to orthotropic materials. The developed computer codes have been geared to work primarily with the Borre and CSIRO HI three-dimensional overcoring measurement probes. Application of the codes to selected case studies, showed that the developed tools were practical and useful for interpreting overcoring stress measurements conducted in anisotropic rock. A quantitative assessment of the effects of anisotropy may thus be obtained, which provides increased reliability in the stress data. Potential gaps in existing data and/or understanding can also be identified. (orig.)

Strength Restoration of Cracked Sandstone and Coal under a Uniaxial Compression Test and Correlated Damage Source Location Based on Acoustic Emissions

Science.gov (United States)

Feng, Xiaowei; Zhang, Nong; Zheng, Xigui; Pan, Dongjiang

2015-01-01

Underground rock masses have shown a general trend of natural balance over billions of years of ground movement. Nonetheless, man-made underground constructions disturb this balance and cause rock stability failure. Fractured rock masses are frequently encountered in underground constructions, and this study aims to restore the strength of rock masses that have experienced considerable fracturing under uniaxial compression. Coal and sandstone from a deep-buried coal mine were chosen as experimental subjects; they were crushed by uniaxial compression and then carefully restored by a chemical adhesive called MEYCO 364 with an innovative self-made device. Finally, the restored specimens were crushed once again by uniaxial compression. Axial stress, axial strain, circumferential strain, and volumetric strain data for the entire process were fully captured and are discussed here. An acoustic emission (AE) testing system was adopted to cooperate with the uniaxial compression system to provide better definitions for crack closure thresholds, crack initiation thresholds, crack damage thresholds, and three-dimensional damage source locations in intact and restored specimens. Several remarkable findings were obtained. The restoration effects of coal are considerably better than those of sandstone because the strength recovery coefficient of the former is 1.20, whereas that of the latter is 0.33, which indicates that MEYCO 364 is particularly valid for fractured rocks whose initial intact peak stress is less than that of MEYCO 364. Secondary cracked traces of restored sandstone almost follow the cracked traces of the initial intact sandstone, and the final failure is mainly caused by decoupling between the adhesive and the rock mass. However, cracked traces of restored coal only partially follow the traces of intact coal, with the final failure of the restored coal being caused by both bonding interface decoupling and self-breakage in coal. Three-dimensional damage source

Strength Restoration of Cracked Sandstone and Coal under a Uniaxial Compression Test and Correlated Damage Source Location Based on Acoustic Emissions.

Directory of Open Access Journals (Sweden)

Xiaowei Feng

Full Text Available Underground rock masses have shown a general trend of natural balance over billions of years of ground movement. Nonetheless, man-made underground constructions disturb this balance and cause rock stability failure. Fractured rock masses are frequently encountered in underground constructions, and this study aims to restore the strength of rock masses that have experienced considerable fracturing under uniaxial compression. Coal and sandstone from a deep-buried coal mine were chosen as experimental subjects; they were crushed by uniaxial compression and then carefully restored by a chemical adhesive called MEYCO 364 with an innovative self-made device. Finally, the restored specimens were crushed once again by uniaxial compression. Axial stress, axial strain, circumferential strain, and volumetric strain data for the entire process were fully captured and are discussed here. An acoustic emission (AE testing system was adopted to cooperate with the uniaxial compression system to provide better definitions for crack closure thresholds, crack initiation thresholds, crack damage thresholds, and three-dimensional damage source locations in intact and restored specimens. Several remarkable findings were obtained. The restoration effects of coal are considerably better than those of sandstone because the strength recovery coefficient of the former is 1.20, whereas that of the latter is 0.33, which indicates that MEYCO 364 is particularly valid for fractured rocks whose initial intact peak stress is less than that of MEYCO 364. Secondary cracked traces of restored sandstone almost follow the cracked traces of the initial intact sandstone, and the final failure is mainly caused by decoupling between the adhesive and the rock mass. However, cracked traces of restored coal only partially follow the traces of intact coal, with the final failure of the restored coal being caused by both bonding interface decoupling and self-breakage in coal. Three

On the penetrability of the floor rock in the stope in coal mining%采动影响下采场底板岩体渗透性研究

Institute of Scientific and Technical Information of China (English)

张风达; 高召宁; 孟祥瑞

2012-01-01

In this paper, we would like to present our research results on the penetrability of the floor rock in the stope in coal mining production. Taking the stope near an aquifer for an example, the paper puts its research focus on the stress redistribution after the coal is mined and penetrability of the stope has changed its regularity. It is from this research perspective that we have developed a stress-permeability interactive model and the equation of the permeability variation by using the fracture mechanics theory and elastic mechanics. In pro-ceeding with our research, we first of all took into full account the effect of crack dip on the permeability of fractured rock, which is likely to be responsible for the destruction of the dominant angle of the fracture by coal mining and by the criterion of compression-shear fracture according to the fracture mechanics theory based on the influence of seepage water pressure. Secondly, based on the dominance angle and the stress-permeability model for fractured rock mass, we have established a stress-permeability interactive model of the dominance angle of the floor fractured rock in the stope. The stress distribution of the stope has been worked out according to the fracture mechanics theory, though it can only be applied to the end of the stope. We have then worked out the equation of permeability zero position failure zone and the stress distribution around the stope through an improved calculation. And, finally, we have established the stress-permeability interactive model of dominance angle of floor rock in the plane stress state by integrating the redistribution of stresses, with the relation of the seepage coefficient ratio and its affecting factors further analyzed. The results show that the permeability of zero position with zone failure and gob increases by the coal mining. And, then, the permeability would be found increasing with the increase of pressure release. Thus, it can be seen that the stress

Some Influences of Underground Coal Gasification on the Environment

Directory of Open Access Journals (Sweden)

Karol Kostúr

2018-05-01

Full Text Available Increasing energy costs and energy demand have renewed global interest in clean coal technologies. Underground Coal Gasification (UCG is an industrial process that converts coal into product gas. UCG is a promising technology with a lot of health, safety and environmental advantages over conventional mining techniques. UCG carries risks to human health, agriculture and the environment. This article briefly analyzes the advantages and negative environmental impacts of UCG. It describes experimental objects, mathematical models as tools for simulation cases and it used coal from UCG experiments in Cigel, Barbara and Wieczorek mines to analyze the environmental impacts of UCG. The gasification converts the carbon in the coal to syngas and heat. We carried out a numerical simulation of the two-dimensional unstable heat conduction in the coal and overburden, with the aim of judging the influence of this heat source on the surroundings, including the surface. The results show that the temperature in the surrounding rock first increases and then decreases with time, the peak of the temperature curve decreases gradually, and its position moves inside the surrounding rock from the ignition point. A small amount of potentially dangerous syngas leaks from the UCG cavity and channels into vulnerable areas depending on working pressures. The danger of explosion and poisoning in vulnerable zones was evaluated by the simulation model. The results show that the danger is real but by monitoring and controlling the air in the vulnerable area it is possible to reduce this risk.

Direct measurement of oxygen in brown coals and carbochemical products by means of fast neutron analysis

International Nuclear Information System (INIS)

Raeppel, P.; Foerster, H.

1990-01-01

Analyses of elemental oxygen by means of fast neutron activation permit high-accuracy measurements of oxygen concentrations in East German brown coal; this applies to run-of-mine brown coal as well as to demineralized brown coal. The relative error was 4% in the first case and 2% in the latter case. Pre-washing with 1n ammonium acetate solution permits direct analyses of the oxygen bonded to the coal minerals. The method is applicable to other carbonaceous materials, e.g. coal ashes, solid hydrogenation residues, cokes, coal extracts, asphaltenes, oils, etc., at oxygen concentrations of 1-50%. (orig.) [de

Designing vertical mine shafts under conditions of increasing shaft depth with rock hoisting to the operating mining level

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1983-05-01

A system for shaft excavation in deep coal mines with mining depth exceeding 1,000 m is discussed. During mine sinking rocks are removed to the ground surface. When depth of a deep mine shaft is increased rocks are removed to the operating mining level, causing lower investment costs than the system with rock hoisting to the ground surface. The Yuzhgiproshakht design firm carries out investigations on the optimum methods for increasing shaft depth in coal mines. Coal mines with the following coal output are included in evaluations: 0.9, 1.2, 1.5, and 1.8 Mt/year. Mine shaft depth of 600, 800, 1000, 1200, 1400 and 1600 m is analyzed. Shaft depth is increased by 100, 200, 300 or 400 m. Shaft sinking rate ranges from 10 to 70 m/month. Effects of rock hoisting from the shaft bottom on the hoisting scheme in a mine shaft are analyzed. Position of hoisting bucket in relation to cages or skips moving in a shaft is investigated. Investigation results are given in 5 schemes. Analyses show that use of a shaft sinking system with rock hoisting to the ground surface during shaft excavation and with rock hoisting to the operating mining level during shaft depth increasing is economical when a shaft with skips is from 7 to 8 m in diameter or when a cage shaft is 6 m, 7 m or 8 m in diameter. Use of standardized shaft excavation systems is recommended. (In Russian)

Instruction manual for the use of CSIR triaxial rock stress measuring equipment

CSIR Research Space (South Africa)

Coetzer, SJ

1998-08-01

Full Text Available This is an updated version of CSIR Report no ME 1763 entitled "Instruction manual for the use for the CSIR triaxial rock stress measuring equipment" by F A Vreede. The manual contains a detailed description of CSIR Triaxial rock stress measuring...

PEMODELAN PENYEBARAN BATUAN POTENSIAL PEMBENTUK ASAM PADA KAWASAN PENAMBANGAN BATUBARA TAMBANG TERBUKA DI MUARA LAWA, KABUPATEN KUTAI BARAT, KALIMANTAN TIMUR (Modeling Distribution of Rock Potential Acid Forming in Open Pit Coal Mining Areas

Directory of Open Access Journals (Sweden)

Shalaho Dina Devy

2016-02-01

Full Text Available ABSTRAK Dampak penambangan batubara tambang terbuka adalah munculnya Air Asam Tambang (AAT di sekitar lingkungan penambangan yang mempengaruhi kualitas air tambang, biota air, kualitas air dan tanah. Oleh karena itu, informasi awal untuk mengantisipasi dampak tersebut, yaitu identifikasi batuan yang berpotensi asam dan memodelkan penyebarannya. Kajian geologi dan mineralogi batuan berperan dalam mengetahui penyebaran batuan Potential Acid Forming (PAF dan Non Acid Forming (NAF. Kawasan tambang yang digunakan sebagai model penelitian berada di Kecamatan Muara Lawa, Kabupaten Kutai Barat, Kalimantan Timur. Hasil dari penelitian mengindikasikan, bahwa dominasi PAF berada di lapisan batu lempung kemudian diikuti batu lanau dan batu pasir dengan penyebaran mengikuti struktur sinklin yang terbatas di lapisan bawah (floor dan lapisan antara (inter burden pada batubara. Sementara itu, batuan NAF menyebar menempati daerah selain batuan PAF. ABSTRACT The impact of open pit coal mining is the emergence of Acid Mine Water (AMD around the mining environment that affect the quality of the mine water, aquatic biota, water and soil quality. Therefore, early information to anticipate these impacts is the identification potential acid rock and distribution model as a guide for the mining plan. Geological and geochemical study of rocks is important in knowing the distribution of rock Potential Acid Formning (PAF and Non Acid Forming (NAF. Mining area which is used as a research model was in Muara Lawa, West Kutai regency, East Kalimantan province. The results of the study indicate, that the dominance of PAF are in layers followed by siltstone, claystone and sandstone with the distribution of rock following the syncline structure in the bottom (floor layer and in the inter-burden layer on coal. Meanwhile, rock NAF spread in areas other than rock PAF.

Method of cutting steeply falling coal beds. [Bacteria, which only grow on methane, are injected into the coal bed and form low viscosity polysaccharides: as a result the coal collapses into the haulage gallery and is hauled away

Energy Technology Data Exchange (ETDEWEB)

Gretsinger, B Ye; Chernyshenko, D V; Levin, A D; Malashenko, Yu R; Shinkovskiy, V A; Shurova, Z P; Volkov, V I

1982-01-01

The purpose of the invention is to reduce outlays for collapse and output of coal by creating artificial cavities of sliding along the coal bed in the surrounding rocks. This goal is achieved because in the well drilled in the bed for the entire height of the level, a suspension of cells of methane-oxidizing microorganisms is injected. The methane-oxidizing microorganisms used are, for example, the thermophilic culture Methylococcus thermophilus of strains ShP which grow at 45-65/sup 0/ C, or the mesophilic culture Methanomonas rubna of strains 15 Sh growing at 20-37/sup 0/ C. As a result of the vital activity of these cultures, polysaccharides are formed with viscosity of 5-7 and 3-4 St respectively. The mine pressure disrupts the blocks between the wells, and the outline section of the steeply dropping coal bed, being destroyed, slides on the products of vital activity of the microorganisms to the haulage gallery. Then the coal drops on cross cuts to the field gallery through which it is transported. Studies established that the only coal substrate which is suitable for growth of these microorganism cultures is methane. The synthesis of one g of absolutely dry substance of these microorganism requires 1.78 g of methane and 4.7 g of oxygen. The cultures are resistant to hydrostatic pressure from 20 to 150 atm and short-term pressure of gradient drops which occur during injection of the cellular suspension into the coal bed. They are filtered through the coal with preservation of the oxidizing and reproductive properties and are cultivated on the methane contained in the bed and form considerable number of exopolysaccarides. The polysaccarides weaken the bond between the bed and the surrounding rocks and serve as a unique lubricant promoting the sliding towards the haulage gallery of the coal blocks destroyed by mine pressure.

Impacts of Natural Surfactant Soybean Phospholipid on Wettability of High-rank Coal Reservoir

Science.gov (United States)

Lyu, S.; Xiao, Y.; Yuan, M.; Wang, S.

2017-12-01

It is significant to change the surface wettability of coal rock with the surfactant in coal mining and coalbed methane exploitation. Soybean phospholipid (SP) is a kind of natural zwitterionic surfactant which is non-toxic and degradable. In order to study the effects of soybean phospholipid on wettability of high-rank coal in Qinshui Basin, some experiments including surface tension test, contact angle measurement on the coal surface, coal fines imbibition, observation of dispersion effect and gas permeability test were carried out, and water locking mechanism of fracturing fluid in micro fractures of coal reservoir was analyzed. The results show that the surface of high-rank coal was negatively charged in solution and of weak hydrophilicity. The soybean phospholipid with the mass fraction of 0.1% reduced the surface tension of water by 69%, and increased the wettability of coal. Meanwhile, the soybean phospholipid helped coal fines to disperse by observation of the filter cake with the scanning electron microscope. The rising rate of soybean phospholipid solution in the pipe filled with coal fines was lower than that of anionic and cationic surfactant, higher than that of clean water and non-ionic surfactant. Composite surfactant made up of soybean phospholipid and OP-10 at the ratio of 1:3 having a low surface tension and large contact angle, reduced the capillary force effectively, which could be conducive to discharge of fracturing fluid from coal reservoir micro fracture and improve the migration channels of gas. Therefore it has a broad application prospect.

Coal Mine Accidents in Bangladesh: Its Causes and Remedial Measures

Directory of Open Access Journals (Sweden)

MD. MINHAJ UDDIN MONIR

2012-12-01

Full Text Available Barapukuria coal mine (BCM is located at Dinajpur district, NW Bangladesh. Total area is about 6.68 km2 and coal was encountered at a depth ranging between 118 and 509 m. Six major coal seams (seam I to seam VI were identified at BCM, of which, thickest one is the seam-VI (~36 m. The estimated coal reserves is about 390 million tons and of this, nearly 64 million tons of coal is extractable. The annual production of coal is about 1 million ton. In this study several parameters were used to explore minimization of accidents and improvement of coal production in BCM. Considering the geological, hydrological and other technical parameters, longwall mining method is applied for extraction of coal. Longwall retreating mining method is also applied for extraction of coal from single face with the operational area protected by self-advancing hydraulic powered roof support (HPRS system. These supports are moved forward causing the roof behind them to form an extensive abandoned area named goaf, which may lead to collapse with air blast. Coal in BCM is extracted from seam VI, using a multislice Longwall top coal caving method. Average ventilated air composition is ~20.94% oxygen, ~79.00% nitrogen, ~0.04% carbon monoxide, and minor water steam with huge dust. Production of coal was completed from 12 Longwall faces of 1st slice from seam VI. During production period several accidents and troubles within BCM have occurred. Poisonous gases such as carbon monoxide were detected during/after development of 1110 Longwall face, which increases up to 6000 ppm, therefore, sealed-off the face with mining equipments. During the development of belt gate roadway of 1101 Longwall face, maximum temperature and humidity increases up to 37 oC and 100%, respectively. Miners of BCM experienced some difficulties to work in that adverse environment. Air return roadway temperature was always 40 to 41oC in 1101 Longwall face during production period, faces temperature 46o

Nanometre-sized pores in coal: Variations between coal basins and coal origin

Science.gov (United States)

Sakurovs, Richard; Koval, Lukas; Grigore, Mihaela; Sokolava, Anna; Ruppert, Leslie F.; Melnichenko, Yuri B.

2018-01-01

We have used small angle neutron scattering (SANS) to investigate the differences in methane and hexane penetration in pores in bituminous coal samples from the U.S., Canada, South Africa, and China, and maceral concentrates from Australian coals. This work is an extension of previous work that showed consistent differences between the extent of penetration by methane into 10–20 nm size pores in inertinite in bituminous coals from Australia, North America and Poland.In this study we have confirmed that there are differences in the response of inertinite to methane and hexane penetration in coals sourced from different coal basins. Inertinite in Permian Australian coals generally has relatively high numbers of pores in the 2.5–250 nm size range and the pores are highly penetrable by methane and hexane; coals sourced from Western Canada had similar penetrability to these Australian coals. However, the penetrability of methane and hexane into inertinite from the Australian Illawarra Coal Measures (also Permian) is substantially less than that of the other Australian coals; there are about 80% fewer 12 nm pores in Illawarra inertinite compared to the other Australian coals examined. The inertinite in coals sourced from South Africa and China had accessibility intermediate between the Illawarra coals and the other Australian coals.The extent of hexane penetration was 10–20% less than CD4 penetration into the same coal and this difference was most pronounced in the 5–50 nm pore size range. Hexane and methane penetrability into the coals showed similar trends with inertinite content.The observed variations in inertinite porosity between coals from different coal regions and coal basins may explain why previous studies differ in their observations of the relationships between gas sorption behavior, permeability, porosity, and maceral composition. These variations are not simply a demarcation between Northern and Southern Hemisphere coals.

Evaluation of Rock Bolt Support for Polish Hard Rock Mines

Science.gov (United States)

Skrzypkowski, Krzysztof

2018-03-01

The article presents different types of rock bolt support used in Polish ore mining. Individual point resin and expansion rock bolt support were characterized. The roof classes for zinc and lead and copper ore mines were presented. Furthermore, in the article laboratory tests of point resin rock bolt support in a geometric scale of 1:1 with minimal fixing length of 0.6 m were made. Static testing of point resin rock bolt support were carried out on a laboratory test facility of Department of Underground Mining which simulate mine conditions for Polish ore and hard coal mining. Laboratory tests of point resin bolts were carried out, especially for the ZGH Bolesław, zinc and lead "Olkusz - Pomorzany" mine. The primary aim of the research was to check whether at the anchoring point length of 0.6 m by means of one and a half resin cartridge, the type bolt "Olkusz - 20A" is able to overcome the load.The second purpose of the study was to obtain load - displacement characteristic with determination of the elastic and plastic range of the bolt. For the best simulation of mine conditions the station steel cylinders with an external diameter of 0.1 m and a length of 0.6 m with a core of rock from the roof of the underground excavations were used.

Study on infrasonic characteristics of coal samples in failure process under uniaxial loading

Directory of Open Access Journals (Sweden)

Bing Jia

Full Text Available To study the precursory failure infrasonic characteristics of coal samples, coal rock stress loading system and infrasonic wave acquisition system were adopted, and infrasonic tests in uniaxial loading process were made for the coal samples in the studied area. Wavelet filtering, fast Fourier transform, and relative infrasonic energy methods were used to analyze the characteristics of the infrasonic waves in the loading process, including time domain characteristics, and relative energy. The analysis results demonstrated that the frequencies of the infrasonic signals in the loading process mainly distribute within 5–10 Hz, which are significantly different from noise signals. The changes of the infrasonic signals show clear periodic characters in time domain. Meanwhile, the relative energy changes of the infrasonic wave also show periodic characters, which are divided into two stages by the yield limit of coal samples, and are clear and easy to be recognized, so that they can be used as the precursory characteristics for recognizing coal sample failures. Moreover, the infrasonic waves generated by coal samples have low frequency and low attenuation, which can be collected without coupling and transmitted in long distance. This study provides an important support for the further in-situ prediction of coal rock failures. Keywords: Infrasound, Relative energy, Time-frequency analysis, Failure prediction, Identification feature

预掘底板岩巷卸压增透方法∗%Methods of destressing and increasing penetration at pre-excavated rock roadway under floor

Institute of Scientific and Technical Information of China (English)

王中华

2016-01-01

针对难抽采煤层,提出了预掘底板岩巷卸压增透方法,理论分析了底板岩巷卸压影响范围一般为巷道半径r 的2~6倍.现场考察了曲江煤矿702底板岩巷围岩位移量最大为38 mm,钻孔瓦斯流量、煤层透气性系数分别为原始煤层的11.1倍、43.2倍,实践表明曲江煤矿702底板岩巷布置在待掘煤巷正下方8~10 m处增透效果显著.%Proposing methods of destressing and increasing penetration at pre-excavated rock road-way under floor for coal seams which are difficult to be drained;theoretically analyzing that the influen-tial incidence of destressing at rock roadway under floor is generally as 2 to 6 times of roadway radius r. In-situ measurements show that the maximum surrounding rock displacement of rock roadway under 702 floor of Qujiang Mine is 38 mm;gas flow rate in borehole and permeability coefficient of coal seam is 1 1.1 and 43.2 times of those of the original coal seam,respectively. The practice shows that rock road-way under 702 floor of Qujiang Mine could make significantly increasing penetration effect when it is placed 8-1 0 meters directly below coal lanes to be excavated.

Sulfur content measurement in coal by X-ray fluorescence method

International Nuclear Information System (INIS)

Cechak, T.; Thinova, L.

2001-01-01

X-ray fluorescence, using backscattering, was employed in the determination of sulfur content and ash content measurement in coal. The results of the methods are given to illustrate the differences between the chemical analysis and X-ray fluorescence method.

Brazilian Tensile Strength of Anisotropic Rocks: Review and New Insights

Directory of Open Access Journals (Sweden)

Tianshou Ma

2018-01-01

Full Text Available Strength anisotropy is one of the most distinct features of anisotropic rocks, and it also normally reveals strong anisotropy in Brazilian test Strength (“BtS”. Theoretical research on the “BtS” of anisotropic rocks is seldom performed, and in particular some significant factors, such as the anisotropic tensile strength of anisotropic rocks, the initial Brazilian disc fracture points, and the stress distribution on the Brazilian disc, are often ignored. The aim of the present paper is to review the state of the art in the experimental studies on the “BtS” of anisotropic rocks since the pioneering work was introduced in 1964, and to propose a novel theoretical method to underpin the failure mechanisms and predict the “BtS” of anisotropic rocks under Brazilian test conditions. The experimental data of Longmaxi Shale-I and Jixi Coal were utilized to verify the proposed method. The results show the predicted “BtS” results show strong agreement with experimental data, the maximum error is only ~6.55% for Longmaxi Shale-I and ~7.50% for Jixi Coal, and the simulated failure patterns of the Longmaxi Shale-I are also consistent with the test results. For the Longmaxi Shale-I, the Brazilian disc experiences tensile failure of the intact rock when 0° ≤ βw ≤ 24°, shear failure along the weakness planes when 24° ≤ βw ≤ 76°, and tensile failure along the weakness planes when 76° ≤ βw ≤ 90°. For the Jixi Coal, the Brazilian disc experiences tensile failure when 0° ≤ βw ≤ 23° or 76° ≤ βw ≤ 90°, shear failure along the butt cleats when 23° ≤ βw ≤ 32°, and shear failure along the face cleats when 32° ≤ βw ≤ 76°. The proposed method can not only be used to predict the “BtS” and underpin the failure mechanisms of anisotropic rocks containing a single group of weakness planes, but can also be generalized for fractured rocks containing multi-groups of weakness planes.

Increasing shaft depth with rock hoisting to the surface. [USSR

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1982-06-01

Schemes of shaft construction with increasing shaft depth depend on: shaft depth, shaft diameter, types of hoisting systems, schemes of shaft reinforcement. Investigations carried out in underground coal mines in the USSR show that waste rock haulage to the surface by an independent hoisting system is most economical. Installation of this system depends on the existing hoisting scheme. When one of the operating cages or skips can be removed without a negative influence on mine operation the system of rock waste hoisting is used. The hoisting bucket used for rock removal from the shaft bottom moves in the shaft section from which one of the cages or skips has been removed. Examples of using this scheme in Donbass, Kuzbass and other coal basins are given. Economic aspects of waste material hoisting to the surface are analyzed. The system is economical when the remaining hoisting system can accept additional loads after removal of a cage or skip from the shaft. Investigations show that use of a bucket with a capacity from 2.5 to 3.0 m/sup 3/ for waste rock removal from the shaft being modernized and deepened is most economical.

Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

Energy Technology Data Exchange (ETDEWEB)

Lee, S.H.D.; Teats, F.G.; Swift, W.M. (Argonne National Lab., IL (United States)); Banerjee, D.D. (Illinois Clean Coal Inst., Carterville, IL (United States))

1993-01-01

Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950[degree]C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

Measurement of alkali-vapor emission from pressurized fluidized-bed combustion of Illinois coals

Energy Technology Data Exchange (ETDEWEB)

Lee, S.H.D.; Teats, F.G.; Swift, W.M. [Argonne National Lab., IL (United States); Banerjee, D.D. [Illinois Clean Coal Inst., Carterville, IL (United States)

1993-04-01

Two Illinois Herrin No. 6 coals and one Illinois Springfield No. 5 coal were separately combusted in a laboratory-scale (15-cm dia) pressurized fluidized-bed combustor (PFBC) combined with an alkali sorber. These coals were combusted in a fluidized bed of Tymochtee dolomite at temperatures ranging from 910 to 950{degree}C and a system pressure of 9.2 atm absolute. Alkali-vapor emission (Na and K) in the PFBC flue gas was determined by the analytical activated-bauxite sorber bed technique developed at Argonne National Laboratory. The test results showed that sodium is the major alkali-vapor species present in the PFBC flue gas, and that the level of sodium-vapor emission increases linearly with both Na and Cl contents in the coals. This suggests that the sodium-vapor emission results from direct vaporization of NaCl present in the coals. The measured alkali-vapor concentration (Na + K), 67 to 190 ppbW, is more than 2.5 times greater than the allowable alkali limit of 24 ppb for an industrial gas turbine. Combusting these coals in a PFBC for power generation may require developing a method to control alkali vapors.

A study on the measurement of coal moisture by the neutron method

International Nuclear Information System (INIS)

Ma Yonghe

1985-01-01

The paper reports the result of measuring coal moisture by the neutron method. A deducting intercept method is used to eliminate the effects of the structural hydrogen and the matrix effect. A measuring device has been developed and its measuring accuracy is less than 1%

Engineering research on coal and gas outburst control for outburst coal seam floor roadway in deep mine%深井突出煤层底板巷防治煤与瓦斯突出工程研究

Institute of Scientific and Technical Information of China (English)

吕有厂; 王玉杰

2017-01-01

文章针对平煤股份首山一矿突出煤层结构复杂、渗透性低,致使预抽煤层瓦斯效果差、效率低的问题,以平煤股份首山一矿突出煤层底板岩巷瓦斯治理工程典型应用模式为研究对象,现场观测分析上覆突出煤层采掘过程中低板岩巷围岩应力变化规律,观测分析卸压瓦斯抽采效果,优化煤岩巷层位关系、为深部突出煤层巷道支护和抽采瓦斯提供指导,对提高深井突出煤层瓦斯治理效果具有重要的借鉴意义.%Aiming at the complex structure and low permeability of outburst coal seam in Shouyishan Coal Mine,resulting in poor effect in the gas pre-drainage,based on the typical application mode of gas control engineering in floor rock roadway of the outburst coal seam,surrounding rock stress variation law of floor rock roadway was observed and analyzed in the field during mining and tunneling in the overlying outburst coal seam.The pressure-relieving gas drainage effect was analyzed,and the position arrangement of coal and rock roadway was optimized.

Radioactivity of combustion residues from coal-fired power stations

International Nuclear Information System (INIS)

Vom Berg, W.; Puch, K.H.

1996-01-01

Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

Simultaneous measurements of transport and poroelastic properties of rocks.

Science.gov (United States)

Hasanov, Azar K; Prasad, Manika; Batzle, Michael L

2017-12-01

A novel laboratory apparatus has been developed for simultaneous measurements of transport and poroelastic rock properties. These transport and poroelastic properties at reservoir pressure and temperature conditions are required inputs for various geoscience applications, such as reservoir simulation, basin modeling, or modeling of pore pressure generation. Traditionally, the transport and poroelastic properties are measured separately using, for example, the oscillating pore pressure method to measure hydraulic transport properties, static strain measurements for elastic properties, and pore volumometry for storage capacity. In addition to time, the separate set of measurements require either aliquot cores or subjecting the same core to multiple pressure tests. We modified the oscillating pore pressure method to build an experimental setup, capable of measuring permeability, storage capacity, and pseudo-bulk modulus of rocks simultaneously. We present here the test method, calibration measurements (capillary tube), and sample measurements (sandstone) of permeability and storage capacity at reservoir conditions. We establish that hydraulically measured storage capacities were overestimated by an order of magnitude when compared to elastically derived ones. Our concurrent measurement of elastic properties during the hydraulic experiment provides an independent constraint on storage capacity.

Thermal expansion of coking coals

Energy Technology Data Exchange (ETDEWEB)

Orlik, M.; Klimek, J. (Vyzkumny a Zkusebni Ustav Nova Hut, Ostrava (Czechoslovakia))

1992-12-01

Analyzes expansion of coal mixtures in coke ovens during coking. Methods for measuring coal expansion on both a laboratory and pilot plant scale are comparatively evaluated. The method, developed, tested and patented in Poland by the Institute for Chemical Coal Processing in Zabrze (Polish standard PN-73/G-04522), is discussed. A laboratory device developed by the Institute for measuring coal expansion is characterized. Expansion of black coal from 10 underground mines in the Ostrava-Karvina coal district and from 9 coal mines in the Upper Silesia basin in Poland is comparatively evaluated. Investigations show that coal expansion reaches a maximum for coal types with a volatile matter ranging from 20 to 25%. With increasing volatile matter in coal, its expansion decreases. Coal expansion increases with increasing swelling index. Coal expansion corresponds with coal dilatation. With increasing coal density its expansion increases. Coal mixtures should be selected in such a way that their expansion does not cause a pressure exceeding 40 MPa. 11 refs.

Rock Expansion Boundary Anti-Permeability Strength and Its Application in the Coal Mine Floor Water Inrush Evaluation%岩石膨胀界限抗渗强度及在底板突水评价中应用

Institute of Scientific and Technical Information of China (English)

段宏飞; 姜振泉; 王一栋; 邵明喜; 赵丽娟; 朱前林

2012-01-01

在岩石全应力应变伺服渗透试验的基础上,提出了岩石膨胀界限抗渗强度的概念,并在此基础上建立了底板突水评价模型,模型考虑了底板岩层有效隔水层厚度、岩性、岩体完整程度以及膨胀界限抗渗强度并详细分析了各参数的取值,以兖矿集团杨村煤矿17煤及其2702工作面突水评价为例,证实了以膨胀界限抗渗强度为基础的底板突水评价模型在突水评价上具有可行性.%To solve the difficulties in coal mine floor water inrush evaluation, on the basis of the servo-controlled permeability test of rock in the complete stress-strain process, we proposed the concept of rock expansion boundary anti-permeability strength, and established a theoretical evaluation model of floor water inrush. In the model, several factors, such as the floor aquifuge effective thickness, lithology, rock mass integrity, and expansion boundary anti-permeability strength were considered, and the taking values of all factors were described in detail. Taking the No. 17 coal seam and 2702 working face in Yangcun coal mine, Yanzhou mining group as an example, it proves that the evaluation model based on the expansive boundary anti-permeability strength is feasible to evaluate the coal mine floor water inrush.

CFD Simulation of Temperature Variation in Carboniferous Rock Strata During UCG

Directory of Open Access Journals (Sweden)

Tomasz Janoszek

2013-01-01

Full Text Available The numerical simulation was based on the computational fluid dynamics formalism in order to identify the change of temperature in rock strata during underground coal gasification (UCG. The calculations simulated the coal gasification process using oxygen and water vapour as a gasification agent in 120 hours. Based on the selected software (Ansys-Fluent a model of underground coal gasification (UCG process was developed. The flow of the gasification agent, the description of the turbulence model, the heat-exchange model and the method of simulation of chemical reactions of gasification are presented herein.

The determination of methane resources from liquidated coal mines

Science.gov (United States)

Trenczek, Stanisław

2017-11-01

The article refers to methane presented in hard coal seams, which may pose a serious risk to workers, as evidenced by examples of incidents, and may also be a high energy source. That second issue concerns the possibility of obtaining methane from liquidated coal mines. There is discussed the current methodology for determination of methane resources from hard coal deposits. Methods of assessing methane emissions from hard coal deposits are given, including the degree of rock mass fracture, which is affected and not affected by mining. Additional criteria for methane recovery from the methane deposit are discussed by one example (of many types) of methane power generation equipment in the context of the estimation of potential viable resources. Finally, the concept of “methane resource exploitation from coal mine” refers to the potential for exploitation of the resource and the acquisition of methane for business purposes.

Coal fires in Northwest China. Detection, monitoring, and prediction using remote sensing data

International Nuclear Information System (INIS)

Zhang, Xiangmin

1998-01-01

Coal fires in China occur within a region that stretches over 5,000 km in the east- western part and 750 km. in the north-southern part. These fires cause an economic and environmental threat by making a significant contribution to the global CO2 budget. The studies made in this thesis can be divided into two parts. Part one is based on field work and laboratory analysis that includes the dating of the paleo coal fires; part two concerns remote sensing applications for the active coal fires. In Chapter 2, the evolution of the paleo coal fires in Toutunhe and Xinjiang areas are studied. Several age groups of burnt rock have been recognized and their relationships with the river terraces will be discussed. The causes of the paleo coal fires are addressed, and the areas of coal fires with different ages have been dated. In Chapter 3, the physical basis of thermal infrared remote sensing for the detection and measurement of coal fires are addressed with an emphasis on the spatial, spectral, and radiometric resolution. In Chapter 4, a method to reduce the effect of solar heating, the main factor of confusion when investigating the thermal anomalies of coal fires, is discussed with the help of a DEM. In Chapter 5, as the coal fires normally occupy only part of one pixel of the Landsat TM thermal channel data, the capability of sub pixel coal fire detection is addressed. In Chapter 6, the airborne data from different wavelengths acquired at different times are studied to analyze the spatial thermal characteristics of the coal fires. Spreading direction and different types of coal fires are studied. Chapter 7 presents, based on multi-sensor data fusion techniques, a hierarchical methodology for detection and monitoring of the coal fires. 120 refs

Identifying sources of respirable quartz and silica dust in underground coal mines in southern West Virginia, western Virginia, and eastern Kentucky

Energy Technology Data Exchange (ETDEWEB)

Schatzel, Steven J. [National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, 626 Cochrans Mill Road, PO Box 18070, Pittsburgh, PA 15236 (United States)

2009-04-01

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers. (author)

Coal mine subsidence and structures

International Nuclear Information System (INIS)

Gray, R.E.

1988-01-01

Underground coal mining has occurred beneath 32 x 10 9 m 2 (8 million acres) of land in the United States and will eventually extend beneath 162 x 10 9 m 2 (40 million acres). Most of this mining has taken place and will take place in the eastern half of the United States. In areas of abandoned mines where total extraction was not achieved, roof collapse, crushing of coal pillars, or punching of coal pillars into softer mine floor or roof rock is now resulting in sinkhole or trough subsidence tens or even hundreds of years after mining. Difference in geology, in mining, and building construction practice between Europe and the United States preclude direct transfer of European subsidence engineering experience. Building damage cannot be related simply to tensile and compressive strains at the ground surface. Recognition of the subsidence damage role played by ground-structure interaction and by structural details is needed

Case Studies of Rock Bursts Under Complicated Geological Conditions During Multi-seam Mining at a Depth of 800 m

Science.gov (United States)

Zhao, Tong-bin; Guo, Wei-yao; Tan, Yun-liang; Yin, Yan-chun; Cai, Lai-sheng; Pan, Jun-feng

2018-05-01

A serious rock burst ("4.19" event) occurred on 19 April 2016 in the No. 4 working face of the No. 10 coal seam in Da'anshan Coal Mine, Jingxi Coalfield. According to the China National Seismological Network, a 2.7 magnitude earthquake was simultaneously recorded in this area. The "4.19" event resulted in damage to the entire longwall face and two gateways that were 105 m in long. In addition, several precursor bursts and mine earthquakes had occurred between October 2014 and April 2016 in the two uphill roadways and the No. 4 working face. In this paper, the engineering geological characteristics and in situ stress field are provided, and then the rock burst distributions are introduced. Next, the temporal and spatial characteristics, geological and mining conditions, and other related essential information are reviewed in detail. The available evidence and possible explanations for the rock burst mechanisms are also presented and discussed. Based on the description and analysis of these bursts, a detailed classification system of rock burst mechanisms is established. According to the main causes and different disturbance stresses (i.e., high/low disturbance stresses and far-field/near-field high disturbance stresses), there are a total of nine types of rock bursts. Thus, some guidelines for controlling or mitigating different types of rock bursts are provided. These experiences and strategies not only provide an essential reference for understanding the different rock burst mechanisms, but also build a critical foundation for selecting mitigation measures and optimizing the related technical parameters during mining or tunnelling under similar conditions.

Study on electromagnetic radiation and mechanical characteristics of coal during an SHPB test

Science.gov (United States)

Chengwu, Li; Qifei, Wang; Pingyang, Lyu

2016-06-01

Dynamic loads provided by a Split Hopkinson pressure bar are applied in the impact failure experiment on coal with an impact velocity of 4.174-17.652 m s-1. The mechanical property characteristics of coal and an electromagnetic radiation signal can be detected and measured during the experiment. The variation of coal stress, strain, incident energy, dissipated energy and other mechanical parameters are analyzed by the unidimensional stress wave theory. It suggests that with an increase of the impact velocity, the mechanical parameters and electromagnetic radiation increased significantly and the dissipated energy of the coal sample has a high discrete growing trend during the failure process of coal impact. Combined with the received energy of the electromagnetic radiation signal, the relationship between these mechanical parameters and electromagnetic radiation during the failure process of coal burst could be analyzed by the grey correlation model. The results show that the descending order of the gray correlation degree between the mechanical characteristics and electromagnetic radiation energy are impact velocity, maximum stress, the average stress, incident energy, the average strain, maximum strain, the average strain rate and dissipation energy. Due to the correlation degree, the impact velocity and incident energy are relatively large, and the main factor affecting the electromagnetic radiation energy of coal is the energy magnitude. While the relationship between extreme stress and the radiation energy change trend is closed, the stress state of coal has a greater impact on electromagnetic radiation than the strain and destruction which can deepen the research of the coal-rock dynamic disaster electromagnetic monitoring technique.

Spatio-temporal evolution of apparent resistivity during coal-seam hydraulic flushing

Science.gov (United States)

Li, Dexing; Wang, Enyuan; Song, Dazhao; Qiu, Liming; Kong, Xiangguo

2018-06-01

Hydraulic flushing in gas predrainage is widely used, but the hydraulic-flushing effect is evaluated in a traditional way, by determining the desorption volume, moisture content, gas drainage rate and other conventional indices. To verify the rationality and feasibility of the multielectrode resistivity method in the evaluation of coal-seam hydraulic flushing and to research the spatio-temporal evolution of apparent resistivity during hydraulic flushing, a field test was conducted in 17# coal seam at Nuodong Mine, Guizhou. During hydraulic flushing, four stages were defined according to the variation in coal rock resistivity with time, namely, the preparation stage, the sharply decreasing stage, the rapidly increasing stage and the steady stage. The apparent resistivity of the coal rock mass is affected mainly by its own degree of fragmentation and flushing volume. A more serious rupture and a greater flushing volume yield a smaller apparent resistivity during the sharply decreasing stage and a higher resistivity during the stable stage. After three months of gas predrainage, the residual gas content and the gas pressure at different points in the expected affected area decrease below the critical value. Changes in the residual gas content and gas pressure at these points are consistent with the apparent resistivity, which validates the rationality and feasibility of the multielectrode resistivity method in evaluating coal-seam hydraulic flushing.

Field trials of aquifer protection in longwall mining of shallow coal seams in China

Energy Technology Data Exchange (ETDEWEB)

Zhang, D.S.; Fan, G.W.; Liu, Y.D.; Ma, L.Q. [State Key Laboratory of Coal Resource & Mine Safety, Xuzhou (China)

2010-09-15

The large-scale mining of shallow coal seams has a significant impact on the overlying aquifers and surface ecological environment. To protect the aquifers and maximize the coal resource recovery, field trials were undertaken during the operation of the LW32201 in Bulianta coal mine, Shendong, China. With a severely weathered rock (SWR) layer and two key strata (KS) in the overlying strata, aquifer protection in longwall mining (APLM) relies mainly on the rapid advance. In some localized zones, special measures should be taken to achieve the APLM, including lowering mining height, backfill and slurry injection. To further understand the mechanism and applicable conditions of the APLM and validate the effectiveness of the APLM, variation of the water table in the aquifer was observed as the longwall face passed through the zone. This paper also discusses the mechanism and basic requirements of the APLM and the relationship between the fall of the water table and the surface subsidence. The results of the field trials indicated that APLM in shallow coal seams could be successful under suitable conditions.

Interpretation of stress measurements around mining cavities in rock salt - a finite-element study

International Nuclear Information System (INIS)

Heusermann, S.

1986-01-01

Finite-element studies of stress measurements using the overcoring method and of large drift fields in rock salt show that the measurements are affected by local stress relaxation occurring near the test borehole and by general time-dependent stress redistribution in the marginal zones of adjacent drifts. Analysis of the overcoring method indicates that the following local effects have to be considered in the interpretation of the test results as opposed to measurements in elastic rock: The inelastic deformation behaviour of rock salt causes stress relaxation at the pilot borehole which can lead to an underestimation of the actual stress state in rock. During overcoring considerable inelastic deformations occur in rock salt which demand a modified interpretation of the measurements and as a result of stress relaxation at the borehole various tests conditions, such as overcoring diameter, pilot borehole diameter and time between drilling and overcoring, have an effect on the test results. (orig./PW)

A novel method for estimating methane emissions from underground coal mines: The Yanma coal mine, China

Science.gov (United States)

Ji, Zhong-Min; Chen, Zhi-Jian; Pan, Jie-Nan; Niu, Qing-He

2017-12-01

As the world's largest coal producer and consumer, China accounts for a relatively high proportion of methane emissions from coal mines. Several estimation methods had been established for the coal mine methane (CMM) emission. However, with large regional differences, various reservoir formation types of coalbed methane (CBM) and due to the complicated geological conditions in China, these methods may be deficient or unsuitable for all the mining areas (e.g. Jiaozuo mining area). By combing the CMM emission characteristics and considering the actual situation of methane emissions from underground coal mine, we found that the methane pre-drainage is a crucial reason creating inaccurate evaluating results for most estimation methods. What makes it so essential is the extensive pre-drainage quantity and its irrelevance with annual coal production. Accordingly, the methane releases were divided into two categories: methane pre-drainage and methane release during mining. On this basis, a pioneering method for estimating CMM emissions was proposed. Taking the Yanma coal mine in the Jiaozuo mining area as a study case, the evaluation method of the pre-drainage methane quantity was established after the correlation analysis between the pre-drainage rate and time. Thereafter, the mining activity influence factor (MAIF) was first introduced to reflect the methane release from the coal and rock seams around where affected by mining activity, and the buried depth was adopted as the predictor of the estimation for future methane emissions. It was verified in the six coal mines of Jiaozuo coalfield (2011) that the new estimation method has the minimum errors of 12.11%, 9.23%, 5.77%, -5.20%, -8.75% and 4.92% respectively comparing with other methods. This paper gives a further insight and proposes a more accurate evaluation method for the CMM emissions, especially for the coal seams with low permeability and strong tectonic deformation in methane outburst coal mines.

The use of the durometer to measure rock hardness in geomorphology. Advantages and limitations.

Science.gov (United States)

Feal-Pérez, Alejandra; Blanco-Chao, Ramón; Valcarcel-Díaz, Marcos; Combes, Martín. A.

2010-05-01

The durometer is a hardness tester developed to measure hardness of metallic materials that has been recently introduced to measure rock hardness in weathering studies. Aoki & Matsukura (2007) highlight some advantages of the durometer compared with the Schmidt Rock Test Hammer: the smaller plunge allows measurements in small surfaces such as taffoni or rock carvings, the wider measurement range and the lower impact energy. This last makes it a non destructive method that can be used on relatively soft rocks. In this work the durometer Equotip (©) has been tested in different environments in the field and in the laboratory to explore its applicability and limitations. We applied the device on small rock samples of granite and limestone and a T-test showed that smaller sample size gave smaller hardness values (p values obtained inside and outside the grooves of the carvings using two different support rings, one flat and one concave. The flat ring was not able to reach the bottom of the groove, meanwhile the concave ring adjusts fairly well given its semi spherical section. A t-test confirmed the difference (p values obtained in the grooves using the flat ring and the higher and less scattered values obtained when the concave ring is used. As a very sensitive device, there are some problems in the use related with rock roughness and rock grain size. In weathered medium to coarse grained rocks, with very irregular surfaces, is not easy to get a good contact between the plunge and the rock surface. A poor contact caused by surface roughness causes the scattering and lowering of rebound values. On the contrary, in homogeneous fine grained rocks and in uniform rock surfaces the device gave very good results. The data obtained in glacial, nival and rock coastal environments showed the potential of the device in the identification of changes in rock hardness. We were able to asses the changes in the weathering degree of glacial striations and marked differences in the

Seismic activity and environment protection in rock burst areas

International Nuclear Information System (INIS)

Travnicek, L.; Holecko, J.; Knotek, S.

1993-01-01

The significance is pointed out of seismic activity caused by mining activities in rock burst areas of the Ostrava-Karvinna district. The need is emphasized of the monitoring of the seismic activity at the Czech-Poland border as needed by the Two-party international committee for exploitation of coal supplies on the common border. The adverse effect of rock burst on the surface is documented by examples provided by the Polish party. The technique is described of investigating the DPB seismic polygon, allowing to evaluate the adverse impact of rock burst on the environment. (author) 1 fig., 8 refs

Investigation of the feasibility of underground coal gasification in North Dakota, United States

International Nuclear Information System (INIS)

Pei, Peng; Nasah, Junior; Solc, Jaroslav; Korom, Scott F.; Laudal, Daniel; Barse, Kirtipal

2016-01-01

Highlights: • A four-year feasibility study of underground coal gasification is presented. • A test site was selected for feasibility investigation. • Gasification test, a hydrogeological study and geomechanical study were performed. • Results suggest favorable conditions for UCG development at the selected site. - Abstract: Underground coal gasification (UCG) is a promising technology that has the potential to recover currently-unmineable coal resources. The technical feasibility and economic success of a UCG project is highly site specific. Any risks associated with UCG, such as subsidence, groundwater contamination, and syngas quality, should be sufficiently evaluated through a feasibility study. This paper presents a four-year UCG feasibility study utilizing lignite seams in North Dakota, United States. Four wells were drilled through the lignite seams at a selected site, and lignite and strata cores were recovered. A geological model of the formation was built, coal and rock properties were analyzed, and field hydrogeological tests and laboratory gasification tests were performed. This work provided valuable insights in rock mechanics, hydrogeology, and coal properties. The study results show that the selected site is suitable for development of a UCG plant because there are minimal induced subsidence risks, there is hydrological isolation from major aquifers and the coal produces desirable syngas quality for liquid fuel production. Methodologies developed in this study will benefit the design, optimization and management of the UCG process.

Measurements for monitoring ground motion resulting from mining operations in the Rhenish brown coal district; Messungen zur Ueberwachung von bergbaubedingten Bodenbewegungen im rheinischen Braunkohlenbergbau

Energy Technology Data Exchange (ETDEWEB)

Duddek, H; Schaefer, W [Rheinbraun AG, Koeln (Germany)

1997-12-31

Coal mining in the Rhenish brown coal district resulted in loose rock slopes with a total height of more than 350 m. Mining operations caused ground motion in open-cast mines, in the slopes and in the region ahead of the face. Internal dumping caused motions of the floors, the overburden tip and te slopes of the open-cast mines. The deformations were measured by different methods, and the evaluations are presented here. As examples, permanent monitoring of a slope using the GEOROBOT measuring system and continuous subsidence measurements in an overburdan dump by means of hydrostatic measuring systems are presented. GEOROBOT ensures quasi-continuous measurements of slope motion with an error of 5-7 mm. Hydrostatic measuring systems on the basis of pressure sensors were developed for measurements of single overburden dump strata and the overburden dump basis during dumping. (orig.) [Deutsch] In den rheinischen Braunkohlentagebauen entstehen Lockergesteinsboeschungen mit Gesamthoehen von mehr als 350 m. Die Gewinnungstaetigkeiten verursachen Entlastungsbewegungen im Tagebau, in den Boeschungen und im Tagebauvorfeld. Die Innenverkippung fuehrt erneut zu Bodenbewegungen im Liegenden, im Kippenkoerper und im Bereich der Tagebauraender. Die auftretenden Deformationen werden mit verschiedenen Messverfahren erfasst, ausgewertet und dargestellt. Beispielhaft werden die permanente Ueberwachung einer Boeschung mittels des automatischen Messsystems GEOROBOT und kontinuierliche Setzungsmessungen in einer Tagebaukippe mit hydrostatischen Messsystemen vorgestellt. Mit GEOROBOT werden quasi kontinuierlich Boeschungsbewegungsmessungen mit einer Genauigkeit von {+-}5 bis 7 mm durchgefuehrt. Auf der Basis von Drucksensoren wurden hydrostatische Messsysteme konzipiert, mit denen Setzungen einzelner Kippscheiben und der Kippenbasis waehrend des Kippenaufbaues ermittelt werden. (orig.)

Measurements for monitoring ground motion resulting from mining operations in the Rhenish brown coal district; Messungen zur Ueberwachung von bergbaubedingten Bodenbewegungen im rheinischen Braunkohlenbergbau

Energy Technology Data Exchange (ETDEWEB)

Duddek, H.; Schaefer, W. [Rheinbraun AG, Koeln (Germany)

1996-12-31

Coal mining in the Rhenish brown coal district resulted in loose rock slopes with a total height of more than 350 m. Mining operations caused ground motion in open-cast mines, in the slopes and in the region ahead of the face. Internal dumping caused motions of the floors, the overburden tip and te slopes of the open-cast mines. The deformations were measured by different methods, and the evaluations are presented here. As examples, permanent monitoring of a slope using the GEOROBOT measuring system and continuous subsidence measurements in an overburdan dump by means of hydrostatic measuring systems are presented. GEOROBOT ensures quasi-continuous measurements of slope motion with an error of 5-7 mm. Hydrostatic measuring systems on the basis of pressure sensors were developed for measurements of single overburden dump strata and the overburden dump basis during dumping. (orig.) [Deutsch] In den rheinischen Braunkohlentagebauen entstehen Lockergesteinsboeschungen mit Gesamthoehen von mehr als 350 m. Die Gewinnungstaetigkeiten verursachen Entlastungsbewegungen im Tagebau, in den Boeschungen und im Tagebauvorfeld. Die Innenverkippung fuehrt erneut zu Bodenbewegungen im Liegenden, im Kippenkoerper und im Bereich der Tagebauraender. Die auftretenden Deformationen werden mit verschiedenen Messverfahren erfasst, ausgewertet und dargestellt. Beispielhaft werden die permanente Ueberwachung einer Boeschung mittels des automatischen Messsystems GEOROBOT und kontinuierliche Setzungsmessungen in einer Tagebaukippe mit hydrostatischen Messsystemen vorgestellt. Mit GEOROBOT werden quasi kontinuierlich Boeschungsbewegungsmessungen mit einer Genauigkeit von {+-}5 bis 7 mm durchgefuehrt. Auf der Basis von Drucksensoren wurden hydrostatische Messsysteme konzipiert, mit denen Setzungen einzelner Kippscheiben und der Kippenbasis waehrend des Kippenaufbaues ermittelt werden. (orig.)

Hydrology of area 8, eastern Coal Province, West Virginia and Ohio

Science.gov (United States)

Friel, E.A.; Ehlke, T.A.; Hobba, W.A.; Ward, S.M.; Schultz, R.A.

1987-01-01

The hydrology of Area 8 in the Ohio River basin in northwestern West Virginia and southeastern Ohio, is influenced by geology and geologic structure. Rocks underlying the area consist of alternating beds of sandstone, siltstone, shale, limestone, and mudstone. Minable coal is contained within the Pennsylvania and Permian rocks. Coal production in 1980 totaled 6.7 million tons from underground mines and one million tons from surface mines. There is a wide range of soil types (29 soil associations) in five land-resource areas. Precipitation averages about 41 inches annually and is greatest at higher altitudes along the eastern boundary of the area. Average annual runoff ranges from 13 to 29 inches per year. The principal land uses are forest and agriculture. Estimated water use during 1980 was 1,170 million gallons per day. Surface-water quality ranges from excellent to poor. The highest iron, manganese and sulfate concentrations were present in mined areas. Well yields range from less than 1 to 350 gallons per minute. Groundwater from the Mississippian rocks contain lesser amounts of dissolved solids than water from the Lower Pennsylvanian rocks. Water high in chloride content is present in some valley areas. (USGS)

Apparatus and method for direct measurement of coal ash sintering and fusion properties at elevated temperatures and pressures

Science.gov (United States)

Khan, M. Rashid

1990-01-01

A high-pressure microdilatometer is provided for measuring the sintering and fusion properties of various coal ashes under the influence of elevated pressures and temperatures in various atmospheres. Electrical resistivity measurements across a sample of coal ash provide a measurement of the onset of the sintering and fusion of the ash particulates while the contraction of the sample during sintering is measured with a linear variable displacement transducer for detecting the initiation of sintering. These measurements of sintering in coal ash at different pressures provide a mechanism by which deleterious problems due to the sintering and fusion of ash in various combustion systems can be minimized or obviated.

Brent coal typing by combined optical and geochemical studies

Energy Technology Data Exchange (ETDEWEB)

Ducazeaux, J.; Le Tran, K.; Nicolas, G. (Societe Nationale des Petroles d' Aquitaine (SNPA), 64 - Pau (France))

1991-12-01

Palynological,petrographical and organic geochemical studies show that various kinds of coal occur throughout the Middle Jurassic Brent Group in the Viking Graben. Two types of coal with strong contrast in terms of source rock potential are thoroughly investigated in this study. It is found that they are relevant to two distinct organic facies. Though having the same organic carbon content, they are very different with respect to the petroleum generating potential, one being a conventional gas-prone coal of type III kerogen and the other one of type II-(III) kerogen which should be considered as an oil-generating coal. Explanations are sought for the difference observed, both geochemically and optically. Palynological study shows the occurrence of two distinct communities of land plants in relation with the depositional environment and climatic changes, whilst coal petrographical study shows that the macerals are unevenly and differently distributed in these two coal types. The original organic material and the depositional environment appear to be the main controlling factors. 13 Refs.; 8 Figs.

Damage evolution of bi-body model composed of weakly cemented soft rock and coal considering different interface effect.

Science.gov (United States)

Zhao, Zenghui; Lv, Xianzhou; Wang, Weiming; Tan, Yunliang

2016-01-01

Considering the structure effect of tunnel stability in western mining of China, three typical kinds of numerical model were respectively built as follows based on the strain softening constitutive model and linear elastic-perfectly plastic model for soft rock and interface: R-M, R-C(s)-M and R-C(w)-M. Calculation results revealed that the stress-strain relation and failure characteristics of the three models vary between each other. The combination model without interface or with a strong interface presented continuous failure, while weak interface exhibited 'cut off' effect. Thus, conceptual models of bi-material model and bi-body model were established. Then numerical experiments of tri-axial compression were carried out for the two models. The relationships between stress evolution, failure zone and deformation rate fluctuations as well as the displacement of interface were detailed analyzed. Results show that two breakaway points of deformation rate actually demonstrate the starting and penetration of the main rupture, respectively. It is distinguishable due to the large fluctuation. The bi-material model shows general continuous failure while bi-body model shows 'V' type shear zone in weak body and failure in strong body near the interface due to the interface effect. With the increasing of confining pressure, the 'cut off' effect of weak interface is not obvious. These conclusions lay the theoretical foundation for further development of constitutive model for soft rock-coal combination body.

Vibration measurement for evaluating the danger of rock-collapse; Rakuseki kikendo hantei no tame no shindo sokutei

Energy Technology Data Exchange (ETDEWEB)

Takeuchi, T; Harada, H [The Nippon Road Co. Ltd., Tokyo (Japan); Mitsuzuka, T [Chishitsu-Keisoku Co. Ltd., Tokyo (Japan)

1997-10-22

Discussions were given on feasibility of a method for investigating a problem of the danger of rock-collapse by applying vibration measurement. The measurement investigation was carried out at a mouth of a tunnel under construction on a highway where the danger of rock-collapse is being investigated according to a qualitative determination criterion. Sixty-four rocks have been evaluated of their danger, with the degree of the danger having been classified to ranks one to three. Vibration measurement was performed on five floating rocks out of the 64 rocks. Vibroscopes were installed on upper portion of the rocks to be investigated and on exposed rocks nearby. The measurement revealed that the vibration has nearly the same amplitude in both of the floating rocks and the settled rocks before and after an automobile has passed, but the floating rocks shake more strongly than the settled rocks while an automobile is passing. This trend appears more noticeably in rocks regarded unstable in the danger determining investigation, indicating presence of close relationship between wave amplitude excited by the automobile and adhesion of the floating rocks. As a result of the discussions, it was made clear that the maximum amplitude ratio and the spectral ratio among the vibration characteristics of the floating rocks can be used as effective determination criteria. 2 refs., 7 figs., 2 tabs.

Development of I and C system for the coal feeder of coal firing plant

Energy Technology Data Exchange (ETDEWEB)

Kim, Teak Soo; Park, Chan Ho [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center

1996-12-31

KECC(Kepco Coal Feeder Control System) receives coal weight, conveyor speed and boiler demand signals. It controls coal flow by generating speed signal of feeder which conveys coal in hopper to pulverizer, displaying measured coal quantity and providing local auto and manual manipulator (author). 33 figs.

A Review of Rock Bolt Monitoring Using Smart Sensors

Directory of Open Access Journals (Sweden)

Gangbing Song

2017-04-01

Full Text Available Rock bolts have been widely used as rock reinforcing members in underground coal mine roadways and tunnels. Failures of rock bolts occur as a result of overloading, corrosion, seismic burst and bad grouting, leading to catastrophic economic and personnel losses. Monitoring the health condition of the rock bolts plays an important role in ensuring the safe operation of underground mines. This work presents a brief introduction on the types of rock bolts followed by a comprehensive review of rock bolt monitoring using smart sensors. Smart sensors that are used to assess rock bolt integrity are reviewed to provide a firm perception of the application of smart sensors for enhanced performance and reliability of rock bolts. The most widely used smart sensors for rock bolt monitoring are the piezoelectric sensors and the fiber optic sensors. The methodologies and principles of these smart sensors are reviewed from the point of view of rock bolt integrity monitoring. The applications of smart sensors in monitoring the critical status of rock bolts, such as the axial force, corrosion occurrence, grout quality and resin delamination, are highlighted. In addition, several prototypes or commercially available smart rock bolt devices are also introduced.

A Review of Rock Bolt Monitoring Using Smart Sensors.

Science.gov (United States)

Song, Gangbing; Li, Weijie; Wang, Bo; Ho, Siu Chun Michael

2017-04-05

Rock bolts have been widely used as rock reinforcing members in underground coal mine roadways and tunnels. Failures of rock bolts occur as a result of overloading, corrosion, seismic burst and bad grouting, leading to catastrophic economic and personnel losses. Monitoring the health condition of the rock bolts plays an important role in ensuring the safe operation of underground mines. This work presents a brief introduction on the types of rock bolts followed by a comprehensive review of rock bolt monitoring using smart sensors. Smart sensors that are used to assess rock bolt integrity are reviewed to provide a firm perception of the application of smart sensors for enhanced performance and reliability of rock bolts. The most widely used smart sensors for rock bolt monitoring are the piezoelectric sensors and the fiber optic sensors. The methodologies and principles of these smart sensors are reviewed from the point of view of rock bolt integrity monitoring. The applications of smart sensors in monitoring the critical status of rock bolts, such as the axial force, corrosion occurrence, grout quality and resin delamination, are highlighted. In addition, several prototypes or commercially available smart rock bolt devices are also introduced.

Reconstruction of 3D Micro Pore Structure of Coal and Simulation of Its Mechanical Properties

Directory of Open Access Journals (Sweden)

Guang-zhe Deng

2017-01-01

Full Text Available This article takes the low permeability coal seam in the coalfield of South Judger Basin in Xinjiang, as a research object. The pore structure characteristics of coal rock mass in low permeability coal seam were analyzed quantitatively using scanning electron microscopy (SEM through the methods of statistics and digital image analysis. Based on the pore structure parameters and the distribution function of the coal rock mass, a three-dimensional porous cylinder model with different porosity was reconstructed by FLAC3D. The numerical simulation study of reconstructed pore model shows that (1 the porosity and the compressive strength have obvious nonlinear relation and satisfy the negative exponential relation; (2 the porosity significantly affects the stress distribution; with the increase of micro porosity, the stress distribution becomes nonuniform; (3 the compressive failures of different models are mainly shear failures, and the shape of fracture section is related to porosity; (4 the variation of seepage coefficient of the pore reconstruction model is consistent with the development of micro cracks. The micro mechanism of the deformation and failure of coal and the interaction of multiphase flow with porosity are revealed, which provides a theoretical reference for the clean development of the low permeability coal seam.

Role of large-scale permeability measurements in fractured rock and their application at Stripa

International Nuclear Information System (INIS)

Witherspoon, P.A.; Wilson, C.R.; Long, J.C.S.; DuBois, A.O.; Gale, J.E.; McPherson, M.

1979-10-01

Completion of the macropermeability experiment will provide: (i) a direct, in situ measurement of the permeability of 10 5 to 10 6 m 3 of rock; (ii) a potential method for confirming the analysis of a series of small scale permeability tests performed in surface and underground boreholes; (iii) a better understanding of the effect to open borehole zone length on pressure measurement; (iv) increased volume in fractured rock; (v) a basis for evaluating the ventilation technique for flow measurement in large scale testing of low permeability rocks

Analysis of the saturated hydrocarbon in coal, carbonaceous mudstone and oils from the lower Jurassic coal measures in the Turpan Basin by GC/MS

International Nuclear Information System (INIS)

Fang Xuan; Meng Qianxiang; Sun Minzhuo; Du Li; Ding Wanren

2005-01-01

Saturated hydrocarbon of coal, carbonaceous mudstone and oils from the Lower Jurassic coal measures in the Turpan basin were studied, and biomarker characteristics and coal thermal maturity analyzed to draw the following conclusions. T here are many similar biomarker characteristics between oil from middle-lower Jurassic of Turpan Basin and coal and carbonaceous mudstone in the same strata. They all contain specific r-lupane, I-norbietane, C 24 -tetracyclic and high content of C 29 -steranes. These characteristics suggest that they have similar matter source of the organic matter derived from matter with abundant high plants. Meanwhile, biomarkers often used to indicate depositional environments characterized by high Pr/Ph ratio, little or no gammacerane and high abundance dibenzofurans, such biomarker distributions are indicative of suboxic and freshwater environment. Although coal and carbonaceous mudstone remain in lower thermal maturity (Ro=0.47-0.53), but C 29 -ββ/(αα+ββ) sterane ratio (0.294-0.489) and bezohopane are detected. Because these ferture are related to bacterial activity, bacterial degradation of organic matter maybe take an important role in coal-derived oil. (authors)

The impacts of coal refuse/fly ash bulk bends on water quality and plant growth

Energy Technology Data Exchange (ETDEWEB)

Stewar, B.R.; Daniels, W.L. [Virginia Polytechnic Institute and State Univ., Blacksburg, VA (United States)

1995-09-01

There is considerable interest in the beneficial reuse of coal fly ash as a soil amendment on coal refuse piles. One method of application would be to blend the coal refuse and the fly ash before deposition in a refuse pile. A field experiment was initiated to measure the effects of bulk blending fly ash with coal refuse on water quality and plant growth parameters. Fly ash (class F) from three sources were used in the experiment. Two of the fly ashes were acidic and the third was alkaline. Trenches were excavated in a coal refuse pile to a depth of 2 m and the refuse was blended with fly ash and then returned to the trench. In other plots the ash was applied as a surface amendment. A treatment of a bulk blend of 5% (w/w) rock phosphate was also included in the experiment. Large volume lysimeters were installed in some trenches to collect the leachates. The fly ash treatments appear to improve the quality of the leachates when compared to the leachates from the untreated plots. The fly ash amended treatments have lower leachate concentrations of Fe and Al. Initially the fly ash treatments showed high levels of leachate B, however those levels have decreased with time. Millet (Setaria italica) yields from the first year of the experiment were highest n the alkaline fly ash and rock phosphate blended plots. In the second growing season, the two bulk blends with alkaline fly ash had the highest yields. In the third growing season all treatments had higher yield levels than the untreated control plots. The positive effects of the fly ash on leachate quality were attributed to the alkalinity of the ash, and the increase in yield was attributed to the increases in water holding capacity due to fly ash treatments.

Estimating the Wet-Rock P-Wave Velocity from the Dry-Rock P-Wave Velocity for Pyroclastic Rocks

Science.gov (United States)

Kahraman, Sair; Fener, Mustafa; Kilic, Cumhur Ozcan

2017-07-01

Seismic methods are widely used for the geotechnical investigations in volcanic areas or for the determination of the engineering properties of pyroclastic rocks in laboratory. Therefore, developing a relation between the wet- and dry-rock P-wave velocities will be helpful for engineers when evaluating the formation characteristics of pyroclastic rocks. To investigate the predictability of the wet-rock P-wave velocity from the dry-rock P-wave velocity for pyroclastic rocks P-wave velocity measurements were conducted on 27 different pyroclastic rocks. In addition, dry-rock S-wave velocity measurements were conducted. The test results were modeled using Gassmann's and Wood's theories and it was seen that estimates for saturated P-wave velocity from the theories fit well measured data. For samples having values of less and greater than 20%, practical equations were derived for reliably estimating wet-rock P-wave velocity as function of dry-rock P-wave velocity.

Using a laser measurement system for monitoring morphological changes on the Strug rock fall, Slovenia

Directory of Open Access Journals (Sweden)

M. Mikoš

2005-01-01

Full Text Available A medium-ranged high performance handheld reflectorless laser measurement system, was used for a morphological survey on the Strug rock fall in W Slovenia in the period from August 2003 to August 2004. The purpose was to evaluate its potential for monitoring ground surface changes in rock fall source areas and to help evaluating morphological changes by measuring distance from fixed points. In the area, 21 fixed geodetic points have been established. Altogether, seven measurement sets with more than 5500 points have been gathered in the rock fall area. Choosing a point cloud with a density of less than 1 point per 10m2 on a very rough rock fall surface failed to be a good solution. The changes on larger areas were shown by displacements of selected significantly large-sized rock blocks with a volume of several m3. Because only smaller changes were observed between the single field series, the rock fall surface generally remained unchanged. Local surface changes of the order of 1 m or more, were clearly shown by measurements in the selected referenced cross sections. The usage of these cross sections gave a possibility to evaluate volumetric changes on the surface. The laser measurement system provided a good replacement for the classical terrestrial geodetic survey equipment, especially when performing remote monitoring of morphological changes in rock fall hazard zones, however, the case is different when fixed points are to be measured precisely.

Gas Permeability Evolution Mechanism and Comprehensive Gas Drainage Technology for Thin Coal Seam Mining

Directory of Open Access Journals (Sweden)

Fangtian Wang

2017-09-01

Full Text Available A thin coal seam mined as a protective coal seam above a gas outburst coal seam plays a central role in decreasing the degree of stress placed on a protected seam, thus increasing gas permeability levels and desorption capacities to dramatically eliminate gas outburst risk for the protected seam. However, when multiple layers of coal seams are present, stress-relieved gas from adjacent coal seams can cause a gas explosion. Thus, the post-drainage of gas from fractured and de-stressed strata should be applied. Comprehensive studies of gas permeability evolution mechanisms and gas seepage rules of protected seams close to protective seams that occur during protective seam mining must be carried out. Based on the case of the LongWall (LW 23209 working face in the Hancheng coal mine, Shaanxi Province, this paper presents a seepage model developed through the FLAC3D software program (version 5.0, Itasca Consulting Group, Inc., Minneapolis, MI, USA from which gas flow characteristics can be reflected by changes in rock mass permeability. A method involving theoretical analysis and numerical simulation was used to analyze stress relief and gas permeability evolution mechanisms present during broken rock mass compaction in a goaf. This process occurs over a reasonable amount of extraction time and in appropriate locations for comprehensive gas extraction technologies. In using this comprehensive gas drainage technological tool, the safe and efficient co-extraction of thin coal seams and gas resources can be realized, thus creating a favorable environment for the safe mining of coal and gas outburst seams.

Survey report for fiscal 1999 on advanced exploitation of coal overseas. Survey of coal exploitation enhancement overseas (Coal industry's measures for persistent low coal price); 1999 nendo kaigaitan kaihatsu kodoka nado chosa. Kaigaitan kaihatsu sokushin chosa (sekitan kakaku teimeika ni okeru sekitan sangyo no taiosaku)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

Surveys were conducted of the trends of coal companies in the U.S. and Australia and of the lookout for new coal field development in Australia for the purpose of contributing to the stable supply of coal in the future. In the U.S., the coal industry has experienced serious changes in these ten years, and various corporations, such as Peabody, Arch Coal, CONSOL, and Kennecott have come to resort to drastic measures for their survival. In Australia, coal price is lower and contract terms are shorter with less demand for coal supply thanks to the economic crisis in Asia. As for demand for coal in Asia, on the other hand, it is deemed that in 2010 there will be a 41% increase over the 1995 level and that, therefore, coal field preservation and new field exploitation are necessary. Since production by strip mining in New South Wales State is to decrease in 2012 and after, it is expected that new projects will start only after 2012. Comprehensive development projects are going to be launched in the areas surrounding the Surat district, Queensland State, and therefore new projects will be easier to start in this region. Since the Surat coal is to be collected after a little stripping, it is expected that it will be able to compete with the Indonesian coal. (NEDO)

Health and Safety Assessment in Lakhra Coal Mines and Its Mitigation Measures

Directory of Open Access Journals (Sweden)

Sallahuddin Panhwar

2017-04-01

Full Text Available The coal mine excavation, transportation and coal cutting process are involved in hazards and risks that can result in fatalities, injuries and diseases, if these are not properly managed. This study has been undertaken for assessment of the safety and health issues amongst the mines workers. Convenience sampling technique was exercised upon 97 mine workers and interviewed with the help of set questionnaire. Personnel protection to workplace environment was monitored by using physical observation and scientific analysis. All parameters were measured against national and international protocols pertaining to labor law at coal mines. It has been determined that very high risk was persisting while mine excavation, coal cutting and transportation processes. Previous record of last five years was suggesting that 04 deaths happened due to roof fall, 03 fatalities occurred through suffocation by inhaling toxic gases, one causality happened via rope haulage pulley, and also one death due to stone fall down from mine shaft. 121 workers injured in different kinds of accidents within five years. It has been learnt from in-depth analysis that maximum of health risk and subsequent health damages are triggering due to lack of awareness, non-compliance of labor as well as mines laws. Thus, it is recommended that government should not allow coal mining contractors and companies, those which are failing in compliance with the suggested standards.

Mineralogical and Geochemical Characteristics of Late Permian Coals from the Mahe Mine, Zhaotong Coalfield, Northeastern Yunnan, China

Directory of Open Access Journals (Sweden)

Xibo Wang

2015-07-01

Full Text Available This paper reports the mineralogical and geochemical compositions of the Late Permian C2, C5a, C5b, C6a, and C6b semianthracite coals from the Mahe mine, northeastern Yunnan, China. Minerals in the coals are mainly made up of quartz, chamosite, kaolinite, mixed-layer illite/smectite (I/S, pyrite, and calcite; followed by anatase, dolomite, siderite, illite and marcasite. Similar to the Late Permian coals from eastern Yunnan, the authigenic quartz and chamosite were precipitated from the weathering solution of Emeishan basalt, while kaolinite and mixed-layer I/S occurring as lenses or thin beds were related to the weathering residual detrital of Emeishan basalt. However, the euhedral quartz and apatite particles in the Mahe coals were attributed to silicic-rock detrital input. It further indicates that there has been silicic igneous eruption in the northeastern Yunnan. Due to the silicic rock detrital input, the Eu/Eu* value of the Mahe coals is lower than that of the Late Permian coals from eastern Yunnan, where the detrital particles were mainly derived from the basalt. The high contents of Sc, V, Cr, Co, Ni, Cu, Ga, and Sn in the Mahe coals were mainly derived from the Kangdian Upland.

An investigation on groundwater recovery rate within sub sea floor tunnels at closed coal mines

International Nuclear Information System (INIS)

Nakata, Eiji; Suenaga, Hiroshi; Oyama, Takahiro; Nomura, Tokisada; Ichihara, Yoshihisa

2008-01-01

The groundwater recovery rate investigated at the closed coal mines extended within sub sea floor tunnels. The Ikeshima and the Taiheiyo coal mine companies exploited the deep coal-bearing strata beneath the ocean. Ikeshima coal mine, excavated S.L. -650m to 6km offshore from Ikeshima island, was closed at November 2002, and Taiheiyo coal mine, excavated S.L. -720m to 9km offshore from Hokkaido, was stopped to excavate from the deep area at January 2003. After closing and stopping of development, we began the investigation of the groundwater recovery rate at both coal mines. The groundwater level of Ikeshima coal mine raised +405m per 1.8 years at the main shaft. The permeability coefficient estimated between 10 - 8 m /s and 10 -6 m/s to use the water recovery rate at the shaft. Otherwise, at Taiheiyo coal mine, we measured the air pressure in tubes used by 3.5km 2.5km, and 1.5km length 2mm diameters tubes to estimate the groundwater recovery level at the 3.2km offshore plug site. Groundwater didn't reach 4.7km (1.5+3.2km) area until November 2004. There were breakdown of shotcleate and rock mass from the roof of tunnel at 5.3km from offshore line. In this paper, we try to show the groundwater recovery rate of these sub sea floor collieries. (author)

MONITORING METAL POLLUTION LEVELS IN MINE WASTES AROUND A COAL MINE SITE USING GIS

Directory of Open Access Journals (Sweden)

D. Sanliyuksel Yucel

2017-11-01

Full Text Available In this case study, metal pollution levels in mine wastes at a coal mine site in Etili coal mine (Can coal basin, NW Turkey are evaluated using geographical information system (GIS tools. Etili coal mine was operated since the 1980s as an open pit. Acid mine drainage is the main environmental problem around the coal mine. The main environmental contamination source is mine wastes stored around the mine site. Mine wastes were dumped over an extensive area along the riverbeds, and are now abandoned. Mine waste samples were homogenously taken at 10 locations within the sampling area of 102.33 ha. The paste pH and electrical conductivity values of mine wastes ranged from 2.87 to 4.17 and 432 to 2430 μS/cm, respectively. Maximum Al, Fe, Mn, Pb, Zn and Ni concentrations of wastes were measured as 109300, 70600, 309.86, 115.2, 38 and 5.3 mg/kg, respectively. The Al, Fe and Pb concentrations of mine wastes are higher than world surface rock average values. The geochemical analysis results from the study area were presented in the form of maps. The GIS based environmental database will serve as a reference study for our future work.

Monitoring Metal Pollution Levels in Mine Wastes around a Coal Mine Site Using GIS

Science.gov (United States)

Sanliyuksel Yucel, D.; Yucel, M. A.; Ileri, B.

2017-11-01

In this case study, metal pollution levels in mine wastes at a coal mine site in Etili coal mine (Can coal basin, NW Turkey) are evaluated using geographical information system (GIS) tools. Etili coal mine was operated since the 1980s as an open pit. Acid mine drainage is the main environmental problem around the coal mine. The main environmental contamination source is mine wastes stored around the mine site. Mine wastes were dumped over an extensive area along the riverbeds, and are now abandoned. Mine waste samples were homogenously taken at 10 locations within the sampling area of 102.33 ha. The paste pH and electrical conductivity values of mine wastes ranged from 2.87 to 4.17 and 432 to 2430 μS/cm, respectively. Maximum Al, Fe, Mn, Pb, Zn and Ni concentrations of wastes were measured as 109300, 70600, 309.86, 115.2, 38 and 5.3 mg/kg, respectively. The Al, Fe and Pb concentrations of mine wastes are higher than world surface rock average values. The geochemical analysis results from the study area were presented in the form of maps. The GIS based environmental database will serve as a reference study for our future work.

Apparatus for the measurement of radionuclide transport rates in rock cores

International Nuclear Information System (INIS)

Weed, H.C.; Koszykowski, R.F.; Dibley, L.L.; Murray, I.

1981-09-01

An apparatus and procedure for the study of radionuclide transport in intact rock cores are presented in this report. This equipment more closely simulates natural conditions of radionuclide transport than do crushed rock columns. The apparatus and the procedure from rock core preparation through data analysis are described. The retardation factors measured are the ratio of the transport rate of a non-retarded radionuclide, such as 3 H, to the transport rate of a retarded radionuclide. Sample results from a study of the transport of /sup 95m/Tc and 85 Sr in brine through a sandstone core are included

Numerical simulation and analysis for low-frequency rock physics measurements

Science.gov (United States)

Dong, Chunhui; Tang, Genyang; Wang, Shangxu; He, Yanxiao

2017-10-01

In recent years, several experimental methods have been introduced to measure the elastic parameters of rocks in the relatively low-frequency range, such as differential acoustic resonance spectroscopy (DARS) and stress-strain measurement. It is necessary to verify the validity and feasibility of the applied measurement method and to quantify the sources and levels of measurement error. Relying solely on the laboratory measurements, however, we cannot evaluate the complete wavefield variation in the apparatus. Numerical simulations of elastic wave propagation, on the other hand, are used to model the wavefield distribution and physical processes in the measurement systems, and to verify the measurement theory and analyze the measurement results. In this paper we provide a numerical simulation method to investigate the acoustic waveform response of the DARS system and the quasi-static responses of the stress-strain system, both of which use axisymmetric apparatus. We applied this method to parameterize the properties of the rock samples, the sample locations and the sensor (hydrophone and strain gauges) locations and simulate the measurement results, i.e. resonance frequencies and axial and radial strains on the sample surface, from the modeled wavefield following the physical experiments. Rock physical parameters were estimated by inversion or direct processing of these data, and showed a perfect match with the true values, thus verifying the validity of the experimental measurements. Error analysis was also conducted for the DARS system with 18 numerical samples, and the sources and levels of error are discussed. In particular, we propose an inversion method for estimating both density and compressibility of these samples. The modeled results also showed fairly good agreement with the real experiment results, justifying the effectiveness and feasibility of our modeling method.

Analyzer for measuring gas contained in the pore space of rocks

Science.gov (United States)

Kudasik, Mateusz; Skoczylas, Norbert

2017-10-01

In the present paper, the authors discussed the functioning of their own analyzer for measuring gas contained in the pore space of high strength rocks. A sample is placed inside a hermetic measuring chamber, and then undergoes impact milling as a result of colliding with the vibrating blade of a knife which is rotationally driven by a high-speed brushless electric motor. The measuring chamber is equipped with all the necessary sensors, i.e. gas, pressure, and temperature sensors. Trial tests involving the comminution of dolomite and anhydrite samples demonstrated that the constructed device is able to break up rocks into grains so fine that they are measured in single microns, and the sensors used in the construction ensure balancing of the released gas. The tests of the analyzer showed that the metrological concept behind it, together with the way it was built, make it fit for measurements of the content and composition of selected gases from the rock pore space. On the basis of the conducted tests of balancing the gases contained in the two samples, it was stated that the gas content of Sample no. 1 was (0.055  ±  0.002) cm3 g-1, and Sample no. 2 contained gas at atmospheric pressure, composed mostly of air.

The modelling and measurement of super-conducting rock joints

International Nuclear Information System (INIS)

Barton, N.; Makurat, A.; Vik, G.; Loset, F.

1985-01-01

Rock joints exhibiting exceptionally high conductivity have been responsible for severe inflows (10-50 m 3 /min.) and flooding in recent Norwegian tunneling projects. These events may be explained by channeling of flow in partially outwashed mineral fillings, associated with deep weathering in ancient basement rocks. There is also evidence to suggest extensional strain with consistent relationships to regional faulting patterns (Selmer-Olsen 1981). Hydraulic fractures making connection with joint systems that are sheared as a result of increased fluid pressure, has been deduced as the mechanism explaining unusually large fluid losses in the geothermal project in Cornwall, England (Pine and Batchelor, 1984). Such mechanisms also introduce uncertainty into water flood and MHF stimulation treatment of fractured oil and gas reservoirs, particularly when principal stress and joint orientations are poorly understood due to coring and stress measurement problems in weak, overstressed reservoir rocks. The possibility of permanent disposal of nuclear waste in crystalline rock, has also focussed attention on highly conductive (''super-conducting'') joints in nuclear waste programmes in Canada, the USA and in Europe. The bi-modal distributions of joint spacing, continuity, apertures and conductivities resulting from the discovery of super-conducting joints has important implications for the location of planned repositories, due to their dramatic impact on potential transport times. In the laboratory a class of super-conducting joints can be created by shear displacement that causes dilation when shearing non-planar features. Recent biaxial shear testing of rock joints recovered in jointed core has identified a strong coupling of conductivity and shear displacement. The theoretical predictions of constitutive relationships for coupled flow in rock joints (Barton et al. 1985) have been broadly verified

Numerical simulation of head top coal's stability control of fully mechanized longwall mining with sublevel caving face in large dip seam

Energy Technology Data Exchange (ETDEWEB)

Li, W.; Wan, Z.; Jiang, F.; Jia, P. [Beijing Science and Technology University, Beijing (China)

2008-07-01

Stability control of the head face's top-coal is one of the key techniques of realising high production and high efficiency in coal mining in fully mechanized top-coal caving face. The characteristics of the stress in the overlying strata of the fully mechanized top-coal caving face and the top coal were analysed using FLAC{sup 3D}. The results show that the tip-to-face top-coal generates a large deformation while it is in the stress-relaxed area. The top-coal in the front of the wall appears to be the failure area for the effect of the abutment pressure that spreads over the coal seam. The surrounding rock of the upper face end is the key part strengthened the control of the rib spalling. The first and frequent appearing phenomenon of losing stability of the powered supports is that the back base of the hydraulic power supports in the top of the face slips. Increasing the quality of support and so on can maintain the stability of surrounding rock. 4 refs., 7 figs., 1 tab.

Integrated petrographic and geochemical study of coal and gas shales from the Sabinas and Chihuahua basins, North of Mexico: estimation of methane gas resources

International Nuclear Information System (INIS)

De La O Burrola, Francisco

2013-01-01

This comprehensive characterization study was performed using organic petrology and geochemistry conducted in the Sabinas basin and Chihuahua in northern Mexico. This information allowed a numerical modeling of gas formation, considering the thermal subsidence of coal and carbonaceous shales. The objectives of this thesis are: - Establish a characterization methodology for the studied rocks - Estimate potential gas generator and its regional distribution - Estimate the methane gas resources For the development of this project, we conducted an intensive campaign representative sampling of coal, carbonaceous shales and coal gas 'in situ'. For the Sabinas basin were studied 97 samples and 114 samples in the basin of Chihuahua. The analyses carried out that were used on the samples analyzed allowed to characterize the kerogen and gas. The methodology used to cross petrographic and geochemical information to analyze the petroleum system by numerical modeling. Analyses were: Petrographic, reflectance %Ro, elemental analysis and immediate, Rock Eval6 R (Bulk rock), isotopic analysis, δ 13 C, δD, (coal gas), scanning electron microscopy, image analysis and analysis of macerals fluid inclusions. The analyzes that were used on the samples allowed to characterize the sample, the kerogen and gas. The methodology used to cross petrographic and geochemical information for analyze the oil system by numerical modeling. Analyses were: Petrographic, reflectance %Ro, elemental analysis and immediate, Rock Eval6 R (Bulk rock), isotopic analysis, δ 13 C, δD, (coal gas), scanning electron microscopy, image analysis and analysis of macerals fluid inclusions A computer program was constructed to cross the information with the analysis of samples of artificial maturation experiments in the laboratory. This approach allowed estimation of methane gas resources generated by coal and carbonaceous shales. The main results obtained for Sabinas Basin were: - The kerogen of the

Study on fluid-solid coupling mechanism for water resistance effect of coal floor based on different combination of rock strata%基于不同岩层组合对底板阻水效应的流固耦合机理研究

Institute of Scientific and Technical Information of China (English)

翟晓荣; 张红梅; 窦仲四; 吴基文; 沈书豪; 周盛全

2016-01-01

为了探究不同岩层组合底板对承压水的阻隔效果,以淮北矿区下组煤底板为研究对象,建立了三种不同组合特征底板模型.基于FISH语言对FLAC3D软件进行二次开发,对流固耦合条件下不同组合特征底板采动应力及围岩渗透性进行了综合分析.结果表明:流固耦合条件下,底板采后应力转换点深度较不考虑底板水压条件下加深,且底板深部出现了明显的卸压现象;硬软型底板采后卸荷程度及应力转换点降幅最大,而软硬相间型底板受最小;硬软型底板采后渗透性提高4.5倍,而软硬相间型底板仅提高1.4倍,研究结果揭示出软硬相间岩层组合底板阻水效果最好,而硬软型底板最差.%To investigate the resistance effect of coal floor with different combination of rock strata on confined water , taking the coal floor of lower coal group in Huaibei mining area as research object , three coal floor models with different combination characteristics were established .The secondary development was conducted on FLAC 3D software based on FISH language , then the comprehensive analysis on the mining stress of coal floor and the permeability of surrounding rock with different com -bination characteristics under the condition of fluid-solid coupling was carried out .The results showed that under the condi-tion of fluid-solid coupling , the depth of stress transition point for coal floor after mining was larger than that without consid -ering the condition of floor water pressure , and the obvious pressure relief phenomenon appeared in the deep floor .The de-creasing amplitude of unloading degree and stress transition point for hard -soft type coal floor after mining were the largest , while those for alternated soft-hard type coal floor were the smallest .The permeability of hard-soft type coal floor after mining increased by 4.5 times, while that of alternated soft-hard type coal floor increased by 1.5 times only.It revealed that

Quartz exposure and increased respiratory symptoms among coal ...

African Journals Online (AJOL)

Quartz has been an inevitable composition of different type of coal mined. The quartz exposures among coalmine workers has been attributed to activities such as cutting the adjacent rock, the roof, the floor and the intrusions. Objective: The aim of the study is to determine the associations between quartz exposures and ...

Naturally Occurring Radioactive Materials in Uranium-Rich Coals and Associated Coal Combustion Residues from China.

Science.gov (United States)

Lauer, Nancy; Vengosh, Avner; Dai, Shifeng

2017-11-21

Most coals in China have uranium concentrations up to 3 ppm, yet several coal deposits are known to be enriched in uranium. Naturally occurring radioactive materials (NORM) in these U-rich coals and associated coal combustion residues (CCRs) have not been well characterized. Here we measure NORM (Th, U, 228 Ra, 226 Ra, and 210 Pb) in coals from eight U-rich coal deposits in China and the associated CCRs from one of these deposits. We compared NORM in these U-rich coals and associated CCRs to CCRs collected from the Beijing area and natural loess sediments from northeastern China. We found elevated U concentrations (up to 476 ppm) that correspond to low 232 Th/ 238 U and 228 Ra/ 226 Ra activity ratios (≪1) in the coal samples. 226 Ra and 228 Ra activities correlate with 238 U and 232 Th activities, respectively, and 226 Ra activities correlate well with 210 Pb activities across all coal samples. We used measured NORM activities and ash yields in coals to model the activities of CCRs from all U-rich coals analyzed in this study. The activities of measured and modeled CCRs derived from U-rich coals exceed the standards for radiation in building materials, particularly for CCRs originating from coals with U > 10 ppm. Since beneficial use of high-U Chinese CCRs in building materials is not a suitable option, careful consideration needs to be taken to limit potential air and water contamination upon disposal of U- and Ra-rich CCRs.

Measurement and modeling of advanced coal conversion processes

Energy Technology Data Exchange (ETDEWEB)

Solomon, P.R.; Serio, M.A.; Hamblen, D.G. (Advanced Fuel Research, Inc., East Hartford, CT (United States)); Smoot, L.D.; Brewster, B.S. (Brigham Young Univ., Provo, UT (United States))

1991-01-01

The objective of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines.

Measurement and modeling of advanced coal conversion processes

Energy Technology Data Exchange (ETDEWEB)

Solomon, P.R.; Serio, M.A.; Hamblen, D.G. (Advanced Fuel Research, Inc., East Hartford, CT (United States)); Smoot, L.D.; Brewster, B.S. (Brigham Young Univ., Provo, UT (United States))

1991-09-25

The objectives of this study are to establish the mechanisms and rates of basic steps in coal conversion processes, to integrate and incorporate this information into comprehensive computer models for coal conversion processes, to evaluate these models and to apply them to gasification, mild gasification and combustion in heat engines. (VC)

High frequency measurement of P- and S-wave velocities on crystalline rock massif surface - methodology of measurement

Science.gov (United States)

Vilhelm, Jan; Slavík, Lubomír

2014-05-01

For the purpose of non-destructive monitoring of rock properties in the underground excavation it is possible to perform repeated high-accuracy P- and S-wave velocity measurements. This contribution deals with preliminary results gained during the preparation of micro-seismic long-term monitoring system. The field velocity measurements were made by pulse-transmission technique directly on the rock outcrop (granite) in Bedrichov gallery (northern Bohemia). The gallery at the experimental site was excavated using TBM (Tunnel Boring Machine) and it is used for drinking water supply, which is conveyed in a pipe. The stable measuring system and its automatic operation lead to the use of piezoceramic transducers both as a seismic source and as a receiver. The length of measuring base at gallery wall was from 0.5 to 3 meters. Different transducer coupling possibilities were tested namely with regard of repeatability of velocity determination. The arrangement of measuring system on the surface of the rock massif causes better sensitivity of S-transducers for P-wave measurement compared with the P-transducers. Similarly P-transducers were found more suitable for S-wave velocity determination then P-transducers. The frequency dependent attenuation of fresh rock massif results in limited frequency content of registered seismic signals. It was found that at the distance between the seismic source and receiver from 0.5 m the frequency components above 40 kHz are significantly attenuated. Therefore for the excitation of seismic wave 100 kHz transducers are most suitable. The limited frequency range should be also taken into account for the shape of electric impulse used for exciting of piezoceramic transducer. The spike pulse generates broad-band seismic signal, short in the time domain. However its energy after low-pass filtration in the rock is significantly lower than the energy of seismic signal generated by square wave pulse. Acknowledgments: This work was partially

Rock Burst Mechanics: Insight from Physical and Mathematical Modelling

Directory of Open Access Journals (Sweden)

J. Vacek

2008-01-01

Full Text Available Rock burst processes in mines are studied by many groups active in the field of geomechanics. Physical and mathematical modelling can be used to better understand the phenomena and mechanisms involved in the bursts. In the present paper we describe both physical and mathematical models of a rock burst occurring in a gallery of a coal mine.For rock bursts (also called bumps to occur, the rock has to possess certain particular rock burst properties leading to accumulation of energy and the potential to release this energy. Such materials may be brittle, or the rock burst may arise at the interfacial zones of two parts of the rock, which have principally different material properties (e.g. in the Poíbram uranium mines.The solution is based on experimental and mathematical modelling. These two methods have to allow the problem to be studied on the basis of three presumptions:· the solution must be time dependent,· the solution must allow the creation of cracks in the rock mass,· the solution must allow an extrusion of rock into an open space (bump effect. 

Comparative emissions from Pakistani coals and traditional coals

Energy Technology Data Exchange (ETDEWEB)

Du, Y X [Guangzhou Medical College (China). Dept. of Hygiene; Huang, L F [Guangzhou Health and Anti-epidemic Station (China)

1994-12-31

Briquette coal has been widely used for domestic cooking and heating in many Chinese cites over the last two decades. To determine whether burning briquette coal contributes significantly to indoor air pollution, a study was performed in cities-of Southern China in which the measured levels of SO{sub 2}, NO{sub x}, TSP, SD, B(a)P in the kitchens of coal burning families were compared with levels obtained in families using gas. Significantly higher contentions of these pollutants, whose peaks correlated with daily cooking episodes, were detected in coal burning families. The levels of TSP and B(a)P were further found to be dependent on cooking methods, with deep frying and stir-frying of meat generating the most indoor TSP and B(a)P. Briquette coal burning was found to be the source of B(a)P contamination in food. A higher incidence of chronic pharyngitis as well as a suppressed salivary bacteriolytic enzyme activity were found in children of coal burning families. Epidemiologic and laboratory studies also show a close association between coal burning and the incidence of lung cancer in females. (author)

Impact of geotechnical factors on the secondary extraction of coal in the Witbank and Northern Highveld Coalfields, specifically related to safety.

CSIR Research Space (South Africa)

Jeffrey, JS

2002-04-01

Full Text Available This report describes a literature review that identified geotechnical factors impacting on unplanned secondary coal extraction. These factors are grouped into nine broad classes of factors; namely, stratigraphy, rock /coal engineering properties...

Stress Distribution in a Coal Seam before and after Bump Initiation

Directory of Open Access Journals (Sweden)

J. Vacek

2001-01-01

Full Text Available This paper deals with to the behaviour of open rock that occurs, for example, during longwall mining in coal mines, in deep tunnel, or shaft excavation.Longwall instability leads to extrusion of rock mass into an open space. This effect is mostly referred to as a bump, or a rock burst. For bumps to occur, the rock has to possess certain particular rock burst properties leading to accumulation of energy and the potential to release this energy. Such materials may be brittle, or the bumps may arise at the interfacial zones of two parts of the rock, that have principally different material properties.The solution is based on experimental and mathematical modelling. These two methods have to allow the problem to be studied on the basis of three presumptions: – the solution must be time dependent – the solution must allow the creation of crack in the rock mass – the solution must allow an extrusion of rock into an open space (bump effect

Portable rapid gas content measurement - an opportunity for a step change in the coal industry?

International Nuclear Information System (INIS)

Beamish, Basil; Kizil, Mehmet; Gu, Ming

2013-01-01

The last major advance in gas content measurement for coal seams was the introduction of the quick crush technique in the early 1990s. This is a laboratory test method that has proven very reliable over the years. Recent laboratory testing using a portable quick crushing device, known as the portable gas content analyser, has produced consistent gas content results for a set of core samples obtained from a single borehole that intersected four coal seams. The retained gas content values obtained for the seams show the same increasing gas content pattern and gas composition change with depth as the standard quick crush technique. Use of the portable gas content analyser provides the opportunity to produce rapid, reliable gas content measurement of coal that could be developed for assessing gas compliance cores and outburst-prone conditions at a mine site.

Measurement and modeling of advanced coal conversion processes. Annual report, October 1990--September 1991

Energy Technology Data Exchange (ETDEWEB)

Solomon, P.R.; Serio, M.A.; Hamblen, D.G.; Smoot, L.D.; Brewster, B.S. [Advanced Fuel Research, Inc., East Hartford, CT (United States)]|[Brigham Young Univ., Provo, UT (United States)

1991-12-31

The overall objective of this program is the development of predictive capability for the design, scale up, simulation, control and feedstock evaluation in advanced coal conversion devices. This program will merge significant advances made in measuring and quantitatively describing the mechanisms in coal conversion behavior. Comprehensive computer codes for mechanistic modeling of entrained-bed gasification. Additional capabilities in predicting pollutant formation will be implemented and the technology will be expanded to fixed-bed reactors.

Paleothermicity in the Central Asturian Coal Basin, North Spain

Energy Technology Data Exchange (ETDEWEB)

Piedad-Sanchez, Noe; Izart, Alain; Martinez, Luis; Elie, Marcel; Menetrier, Cedric [UMR G2R/7566-Geologie et Gestion des Ressources Minerales et Energetiques, Equipe Dynamique des Bassins Sedimentaires et des Matieres Organiques, Faculte des Sciences, Universite Henri Poincare, Nancy 1, BP-239, Boulevard des Aiguillettes, 54506 Vandoeuvre-les-Nancy Cedex (France); Suarez-Ruiz, Isabel [Instituto Nacional del Carbon (CSIC), C/ Francisco Pintado Fe, 26, 33011-Oviedo (Spain)

2004-06-23

This research shows for the first time maps of vitrinite reflectances and paleotemperatures from the Central Asturian Coal Basin (North Spain) which is a Carboniferous (Pennsylvanian) Basin mainly of Moscovian age. Vitrinite reflectance values decrease from north to south whereas volatile matter distribution increases from south to north. Vitrinite reflectance and volatile matter parameters indicate a coal rank ranging from high volatile bituminous coal in the north, to semianthracite and anthracite in the south. Rock-Eval data show that the organic matter of this basin is Type III kerogen, with a maturation ranging from oil to gas window. Paleotemperatures were calculated by diverse methods using vitrinite reflectance data for different durations of heating and Rock-Eval results. The calculated paleotemperatures and vertical paleotemperature gradients decrease from south to north. The thermal gradient variation in the Central Asturian Coal Basin points to the influence of at least two heating events that affected the organic matter. The first associated with a regular geothermal gradient operating over a long period of time, and the second linked to a southern granitic event of short duration estimated by tectonic data. The short thermal event was located at the end of sedimentation (Late Moscovian and Late Westphalian D) and after folding, but before the overthrusting during the Asturian tectonic phase located before the Early Kasimovian (Cantabrian and Stephanian) deposits. Finally, a simulation of paleotemperatures around the granitic pluton was calculated and compared to maps of paleotemperatures obtained by various methods. These maps refer to an initial depth of one or two km in accordance with the selected methods that are compatible with local erosion. This approach was preferred in order to explain the metamorphism of coal, rather than the hypothesis of hydrothermal fluid flow proposed for other foreland basins. This regional thermal anomaly could be

Laboratory measurements of P- and S-wave anisotropy in synthetic rocks by 3D printing

Science.gov (United States)

Kong, L.; Ostadhassan, M.; Tamimi, N.; Li, C.; Alexeyev, A.

2017-12-01

Synthetic rocks have been widely used to realize the models with controlled factors in rock physics and geomechanics experiments. Additive manufacturing technology, known as 3D printing, is becoming a popular method to produce the synthetic rocks as the advantages of timesaving, economics, and control. In terms of mechanical properties, the duplicability of 3D printed rock towards a natural rock has been studied whereas the seismic anisotropy still remains unknown as being the key factor in conducting rock physics experiments. This study utilized a 3D printer with gypsum as the ink to manufacture a series of synthetic rocks that have the shapes of octagonal prisms, with half of them printed from lateral and another half from the bottom. An ultrasonic investigation system was set up to measure the P- and S- wave velocities at different frequencies while samples were under dry conditions. The results show the impact of layered property on the P- and S- wave velocities. The measurement results were compared with the predicted results of Hudson model, demonstrating that the synthetic rock from 3D printing is a transverse isotropic model. The seismic anisotropy indicates that the availability of using 3D printed rocks to duplicate natural rocks for the purpose of recreating the experiments of rock physics. Future experiments will be performed on the dependence of seismic anisotropy on fracture geometry and density in 3D printed synthetic rocks.

Adjustments of microwave-based measurements on coal moisture using natural radioactivity techniques

Energy Technology Data Exchange (ETDEWEB)

Prieto-Fernandez, I.; Luengo-Garcia, J.C.; Alonso-Hidalgo, M.; Folgueras-Diaz, B. [University of Oviedo, Gijon (Spain)

2006-01-07

The use of nonconventional on-line measurements of moisture and ash content in coal is presented. The background research is briefly reviewed. The possibilities of adjusting microwave-based moisture measurements using natural radioactive techniques, and vice versa, are proposed. The results obtained from the simultaneous analysis of moisture and ash content as well as the correlation improvements are shown.

Interim report on Tanjung Enim IV coal exploration project. South Arahan area (1998/1999)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-05-01

The exploration project in Indonesia covered geological mapping, drilling, geophysical logging, underground water pumping tests, vertical seismic profiling (VSP), and seismic reflection survey. Ten boreholes were drilled. Moreover, coal property analysis, geotechnical rock test, geochemical analysis, and the like were conducted by examining core specimens sampled from the boreholes. It was found that there are three main coal beds which continuously extend to the two ends of the synclinic structure. It was also found that there is a 6m-thick coal bed 200m further below the three main coal beds, and it is estimated to produce approximately 6,000kcal/kg. Coal from two of the three beds produces 5,000kcal/kg, containing but a little ash and sulfur. Coal from the third includes 1.17% of sulfur. Coal in all the beds is summed up, and then it is estimated that there is approximately 1,054-million tons of coal in reserve in the South Arahan area. (NEDO)

Opencast planning of the Woelfersheim mines of PreussenElektra with due attention to rock mechanics conditions

Energy Technology Data Exchange (ETDEWEB)

Liebscher, S

1989-04-01

The change-over from underground to opencast operation in the Woelfersheim workings commenced in 1962 to ensure the coal supply to the power station that was expanded by a 64 MW unit. With due attention to soil mechanics features, a working scheme was evolved for the dredger-mobile conveyor-belt-stacker-system, which as regards the arrangement of the cuts takes into account not only the required output, but also the rock mechanics conditions in the Woelfersheim workings. Operational problems that occur in connection with changes to batter slopes are discussed in the present paper. After the coal has been worked-out in the individual sections of the field opencast residual pits remain, the slopes of which have to be stabilized by means of appropriate measures. (orig.).

Classes of organic molecules targeted by a methanogenic microbial consortium grown on sedimentary rocks of various maturities

Directory of Open Access Journals (Sweden)

Margaux eMesle

2015-06-01

Full Text Available Organic-rich shales are populated by methanogenic consortia that are able to degrade the fossilized organic matter into methane gas. To identify the organic fraction effectively degraded, we have sequentially depleted two types of organic-rich rocks, shales and coal, at two different maturities, by successive solvent extractions to remove the most soluble fractions (maltenes and asphaltenes and isolate kerogen. We show the ability of the consortia to produce methane from all rock samples, including those containing the most refractory organic matter, i.e. the kerogen. Shales yielded higher methane production than lignite and coal. Mature rocks yielded more methane than immature rocks. Surprisingly, the efficiency of the consortia was not influenced by the removal of the easily biodegradable fractions contained in the maltenes and asphaltenes. This suggests that one of the limitations of organic matter degradation in situ may be the accessibility of the carbon and energy source. Indeed, bitumen has a colloidal structure that may limit the accessibility to asphaltenes in the bulk rock. Solvent extractions might favor the access to asphaltenes and kerogen by modifying the spatial organization of the molecules in the rock matrix.

The Late Paleozoic relative gas fields of coal measure in China and their significances on the natural gas industry

Directory of Open Access Journals (Sweden)

Chenchen Fang

2016-12-01

Full Text Available The coal measure gas sources of coal-derived gas fields in the Late Paleozoic China are the Lower Carboniferous Dishuiquan Formation, the Upper Carboniferous Batamayineishan Formation and Benxi Formation, the Lower Permian Taiyuan Formation and Shanxi Formation, and the Upper Permian Longtan Formation. The coal-derived gas accumulates in Ordovician, Carboniferous, Permian, and Paleocene reservoirs and are distributed in Ordos Basin, Bohai Bay Basin, Junggar Basin, and Sichuan Basin. There are 16 gas fields and 12 of them are large gas fields such as the Sulige large gas field which is China's largest reserve with the highest annual output. According to component and alkane carbon isotope data of 99 gas samples, they are distinguished to be coal-derived gas from coal-derived gas with δ13C2 > −28.5‰ and δ13C1 -δ13C2 -δ13C3 identification chart. The Late Paleozoic relative gas fields of coal measure are significant for the Chinese natural gas industry: proven natural gas geological reserves and annual output of them account for 1/3 in China, and the gas source of three significant large gas fields is coal-derived, which of five significant large gas fields supporting China to be a great gas producing country. The average reserves of the gas fields and the large gas fields formed from the late Paleozoic coal measure are 5.3 and 1.7 times that of the gas fields and the large gas fields in China.

Study on the Low-Temperature Oxidation Law in the Co-Mining Face of Coal and Oil Shale in a Goaf—A Case Study in the Liangjia Coal Mine, China

Directory of Open Access Journals (Sweden)

Gang Wang

2018-01-01

Full Text Available The low-temperature oxidation law of coal and rock mass is the basis to study spontaneous combustion in goafs. In this paper, the low-temperature oxidation laws of coal, oil shale, and mixtures of coal and oil shale were studied by using laboratory programmed heating experiments combined with a field beam tube monitoring system. The results from the programmed heating experiments showed that the heat released from oil shale was less than that from coal. Coal had a lower carbon monoxide (CO-producing temperature than oil shale, and the mixture showed obvious inhibiting effects on CO production with an average CO concentration of about 38% of that for coal. Index gases were selected in different stages to determine the critical turning point temperature for each stage. The field beam tube monitoring system showed that the temperature field of the 1105 co-mining face of coal and oil shale in the goaf of the Liangjia Coal Mine presented a ladder-like distribution, and CO concentration was the highest for coal and lower for the mixture of coal and oil shale, indicating that the mixture of coal with oil shale had an inhibiting effect on CO production, consistent with the results from the programmed heating experiments.

X-ray structural analysis of some Indian coals

International Nuclear Information System (INIS)

Binoy K Saikia, B.K.

2009-01-01

Coal is one of the most abundant energy resources and has the capability to meet future energy needs with high reliability. The use of coal as an energy source and as a source of organic chemicals feedstock may become more important in the future. It is physically and chemically a heterogeneous and carbonaceous rock which consists of organic and inorganic materials. Assam coal has been, and continuous to be, a valuable energy source, especially for the various industry in India and for liquefactions of coal. The basic chemical structure of coal that has been widely accepted today was built up from the synthesis of results obtained from X-ray diffraction data. The present paper reports a comparative investigation of coals from different collieries/areas of Makum coal field, Assam viz. Ledo, Tikak, Baragolai, Tipong and Tirap collieries Makum coal field, Assam with the help of X-ray diffraction (XRD). The X-ray diffraction patterns indicate that the coals are amorphous in nature. The present XRD method includes the evaluation of Function of Radial Distribution of Atoms (FRDA) and structural interpretations of the coals from their Radial Distribution Function (RDF) plots after proper corrections for air scatter, absorption by sample and polarization. The curve intensity profiles in FRDA clearly show quite regular molecular packets for these coals. The first maxima in the FRDA curves was obtained at r= 0.4 Amstrong for Ledo, Baragolai and Tipong coals whereas for Tikak coal it was observed at r= 0.5 Amstrong. The first maximum in the pair distribution function plots, G (r) of Ledo, Tikak, and Tipong coals was obtained at r=0.15 nm whereas for Baragolai and Tirap coals it was observed at r=0.14 nm and r=0.12 nm respectively, which relates to the C=C (aliphatic/aromatic) bonds in coal matrix. The Assam coal samples from Ledo, Tikak, Baragolai, Tipong and Tirap collieries of Makum coalfield have almost the same RDF inter-atomic distances except slight differences. This

Coal background paper. Coal demand

International Nuclear Information System (INIS)

1997-01-01

Statistical data are presented on coal demands in IEA and OECD member countries and in other countries. Coal coaking and coaking coal consumption data are tabulated, and IEA secretariat's coal demand projections are summarized. Coal supply and production data by countries are given. Finally, coal trade data are presented, broken down for hard coal, steam coal, coking coal (imports and export). (R.P.)

Arctic vegetation damage by winter-generated coal mining pollution released upon thawing

DEFF Research Database (Denmark)

Elberling, B.; Søndergaard, J.; Jensen, L.A.

2007-01-01

summer period. Here we show that heat generation within an oxidizing, sulfidic, coal-mining waste-rock pile in Svalbard (78° N) is high enough to keep the pile warm (roughly 5 °C throughout the year) despite mean annual air temperatures below -5 °C. Consequently, weathering processes continue year...... the adverse environmental impacts of cold region coal-mining need to pay more attention to winter processes including AMD generation and accumulation of weathering products....

Stress distribution characteristics in the vicinity of coal seam floor

Science.gov (United States)

Cui, Zimo; Chanda, Emmanuel; Zhao, Jingli; Wang, Zhihe

2018-01-01

Although longwall top-coal caving (LTCC) has been a popular, more productive and cost-effective method in recent years, roadway floor heave and rock bursts frequently appear when exploiting such coal seams with large dip angle. This paper proposes addressing this problem by adopting three-dimensional roadway layout of stagger arrangement (3-D RLSA). In this study, the first step was to analyse the stress distribution characteristics in the vicinity of coal seam floor based on the stress slip line field theory. In the second step, numerical calculation using FLAC3D was conducted. Finally, an evaluation of the 3-D RLSA for solving this particular issue was given. Results indicate that for this particular mine the proposed 3-D RLSA results in 24% increase in the coal recovery ratio and a modest reduction in excavation and maintenance costs compared to the conventional LTCC method.

Ore controlling oxidized zonation epigenetic uranium-coal deposits and regularities in lignite transformations

International Nuclear Information System (INIS)

Uspenskij, V.A.; Kulakova, Ya.M.

1982-01-01

Complex of analytical methods was used to study epigenetic transformations in uranium-coal ore manifestation. To clarify the principle scheme of oxidized zonation in coals the materials, related to three similar objects were used. When comparing obtained epigenetic column with columns of similar ore objects the principle scheme of oxidized epigenetic zonation for ancient infiltration uranium-coal deposits was specified; general regularities of eignite transformations and characteristics of profile distribution of uranium and accessory metal zonations were revealed. Infiltration processes, proceeded in coal measureses, formed the steady epigenetic oxidized zonation: O - zone of barren unoxidized coals, 1 - zone of ore-bearing unoxidized coals, 2 - zone of weakly ore-bearing oxidized coals, 3 - zone of oxidized terrigenous rocks with zonules of development of yellow and red iron hydroxides. Capacities of some zones and zonules reflect the intensity and duration of ore-forming processes. Distribution of U and accessory elements obeys completely epigenetic zonation. It is assumed, that ancient infiltration uranium-coal deposits formed due to weakly uranium-bearing oxygen-containing waters

Boiler briquette coal versus raw coal: Part I--Stack gas emissions.

Science.gov (United States)

Ge, S; Bai, Z; Liu, W; Zhu, T; Wang, T; Qing, S; Zhang, J

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM10 and PM2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM10, 0.38 for PM2.5, 20.7 for SO2, and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM10, 0.30 for PM2.5, 7.5 for SO2, and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM10, 0.87 for PM2.5, 46.7 for SO2, and 15 for CO, while those of the BB-coal were 2.51 for PM10, 0.79 for PM2.5, 19.9 for SO2, and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/steam conversion factors, were 0.23 for PM10, 0.12 for PM2.5, 6.4 for SO2, and 2.0 for CO, while those of the BB-coal were 0.30 for PM10, 0.094 for PM2.5, 2.4 for SO2, and 1.7 for CO. PM10 and PM2.5 elemental compositions are also presented for both types of coal tested in the study.

Boiler Briquette Coal versus Raw Coal: Part I-Stack Gas Emissions.

Science.gov (United States)

Ge, Su; Bai, Zhipeng; Liu, Weili; Zhu, Tan; Wang, Tongjian; Qing, Sheng; Zhang, Junfeng

2001-04-01

Stack gas emissions were characterized for a steam-generating boiler commonly used in China. The boiler was tested when fired with a newly formulated boiler briquette coal (BB-coal) and when fired with conventional raw coal (R-coal). The stack gas emissions were analyzed to determine emission rates and emission factors and to develop chemical source profiles. A dilution source sampling system was used to collect PM on both Teflon membrane filters and quartz fiber filters. The Teflon filters were analyzed gravimetrically for PM 10 and PM 2.5 mass concentrations and by X-ray fluorescence (XRF) for trace elements. The quartz fiber filters were analyzed for organic carbon (OC) and elemental carbon (EC) using a thermal/optical reflectance technique. Sulfur dioxide was measured using the standard wet chemistry method. Carbon monoxide was measured using an Orsat combustion analyzer. The emission rates of the R-coal combustion (in kg/hr), determined using the measured stack gas concentrations and the stack gas emission rates, were 0.74 for PM 10 , 0.38 for PM 25 , 20.7 for SO 2 , and 6.8 for CO, while those of the BB-coal combustion were 0.95 for PM 10 , 0.30 for PM 2 5 , 7.5 for SO 2 , and 5.3 for CO. The fuel-mass-based emission factors (in g/kg) of the R-coal, determined using the emission rates and the fuel burn rates, were 1.68 for PM 10 , 0.87 for PM 25 , 46.7 for SO 2 , and 15 for CO, while those of the BB-coal were 2.51 for PM 10 , 0.79 for PM 2.5 , 19.9 for SO 2 , and 14 for CO. The task-based emission factors (in g/ton steam generated) of the R-coal, determined using the fuel-mass-based emission factors and the coal/ steam conversion factors, were 0.23 for PM 10 , 0.12 for PM 2.5 , 6.4 for SO 2 , and 2.0 for CO, while those of the BB-coal were 0.30 for PM 10 , 0.094 for PM 2.5 , 2.4 for SO 2 , and 1.7 for CO. PM 10 and PM 2.5 elemental compositions are also presented for both types of coal tested in the study.

Complex Contact Angles Calculated from Capillary Rise Measurements on Rock Fracture Faces

Science.gov (United States)

Perfect, E.; Gates, C. H.; Brabazon, J. W.; Santodonato, L. J.; Dhiman, I.; Bilheux, H.; Bilheux, J. C.; Lokitz, B. S.

2017-12-01

Contact angles for fluids in unconventional reservoir rocks are needed for modeling hydraulic fracturing leakoff and subsequent oil and gas extraction. Contact angle measurements for wetting fluids on rocks are normally performed using polished flat surfaces. However, such prepared surfaces are not representative of natural rock fracture faces, which have been shown to be rough over multiple scales. We applied a variant of the Wilhelmy plate method for determining contact angle from the height of capillary rise on a vertical surface to the wetting of rock fracture faces by water in the presence of air. Cylindrical core samples (5.05 cm long x 2.54 cm diameter) of Mancos shale and 6 other rock types were investigated. Mode I fractures were created within the cores using the Brazilian method. Each fractured core was then separated into halves exposing the fracture faces. One fracture face from each rock type was oriented parallel to a collimated neutron beam in the CG-1D imaging instrument at ORNL's High Flux Isotope Reactor. Neutron radiography was performed using the multi-channel plate detector with a spatial resolution of 50 μm. Images were acquired every 60 s after a water reservoir contacted the base of the fracture face. The images were normalized to the initial dry condition so that the upward movement of water on the fracture face was clearly visible. The height of wetting at equilibrium was measured on the normalized images using ImageJ. Contact angles were also measured on polished flat surfaces using the conventional sessile drop method. Equilibrium capillary rise on the exposed fracture faces was up to 8.5 times greater than that predicted for polished flat surfaces from the sessile drop measurements. These results indicate that rock fracture faces are hyperhydrophilic (i.e., the height of capillary rise is greater than that predicted for a contact angle of zero degrees). The use of complex numbers permitted calculation of imaginary contact angles for

Preparation of rock samples for measurement of the thermal neutron macroscopic absorption cross-section

International Nuclear Information System (INIS)

Czubek, J.A.; Burda, J.; Drozdowicz, K.; Igielski, A.; Kowalik, W.; Krynicka-Drozdowicz, E.; Woznicka, U.

1986-03-01

Preparation of rock samples for the measurement of the thermal neutron macroscopic absorption cross-section in small cylindrical two-region systems by a pulsed technique is presented. Requirements which should be fulfilled during the preparation of the samples due to physical assumptions of the method are given. A cylindrical vessel is filled with crushed rock and saturated with a medium strongly absorbing thermal neutrons. Water solutions of boric acid of well-known macroscopic absorption cross-section are used. Mass contributions of the components in the sample are specified. This is necessary for the calculation of the thermal neutron macroscopic absorption cross-section of the rock matrix. The conditions necessary for assuring the required accuracy of the measurement are given and the detailed procedure of preparation of the rock sample is described. (author)

Investigation on Mechanical Behaviour of Coal and Overburden Rock for UCG

NARCIS (Netherlands)

Shojai Kaveh, N.; Barnhoorn, A.; Wolf, K.H.A.A.

2015-01-01

In recent years, the coupled UCG-CCS process has been considered as another potential CCS option, which can offer integrated energy recovery from coal and storage of CO2. However, existing potential problems may counteract its potential benefits. To develop a generic UCG-CCS site characterisation

Prevention of spontaneous combustion in coal stockpiles : Experimental results in coal storage yard

NARCIS (Netherlands)

Fierro, V.; Miranda, J.L.; Romero, C.; Andrés, J.M.; Arriaga, A.; Schmal, D.; Visser, G.H.

1999-01-01

The spontaneous ignition of coal stockpiles is a serious economic and safety problem. This paper deals with oxidation and spontaneous combustion of coal piles laid in coal storage yard and the measures to avoid the heat losses produced. Investigations on self heating were carried out with five test

Coal cleaning: a viable strategy for reduced carbon emissions and improved environment in China?

International Nuclear Information System (INIS)

Glomsroed, Solveig; Wei Taoyuan

2005-01-01

China is a dominant energy consumer in global context and current energy forecasts emphasise that China's future energy consumption also will rely heavily on coal. The coal use is the major source of the greenhouse gas CO 2 and particles causing serious health damage. This paper looks into the question if coal washing might work as low cost strategy for both CO 2 and particle emission reductions. Coal washing removes dirt and rock from raw coal, resulting in a coal product with higher thermal energy and less air pollutants. Coal cleaning capacity has so far not been developed in line with the market potential. In this paper an emerging market for cleaned coal is studied within a CGE model for China. The macro approach catches the repercussions of coal cleaning through increased energy efficiency, lower coal transportation costs and crowding out effect of investments in coal washing plants. Coal cleaning stimulates economic growth and reduces particle emissions, but total energy use, coal use and CO 2 emissions increase through a rebound effect supported by the vast reserve of underemployed labourers. A carbon tax on fossil fuel combustion has a limited effect on total emissions. The reason is a coal leakage to tax exempted processing industries

Caving thickness effects of surrounding rocks macro stress shell evolving characteristics

Institute of Scientific and Technical Information of China (English)

XIE Guang-xiang; YANG Ke

2009-01-01

In order to explore the influence of different caving thicknesses on the MSS dis-tribution and evolving characteristics of surrounding rocks in unsymmetrical disposal and fully mechanized top-coal caving (FMTC), based on unsymmetrical disposal characteris-tics, the analyses of numerical simulation, material simulation and in-situ observation were synthetically applied according to the geological and technical conditions of the 1151(3) working face in Xieqiao Mine. The results show that the stress peak value of the MSS-base and the ratio of MSS-body height to caving thickness are nonlinear and inversely proportional to the caving thickness. The MSS-base width, the MSS-body height, the MSS-base distance to working face wall and the rise distance of MSS-base beside coal pillar are nonlinear and directly proportional to the caving thickness. The characteristics of MSS distribution and its evolving rules of surrounding rocks and the integrated caving thickness effects are obtained. The investigations will provide lots of theoretic references to the surrounding rocks' stability control of the working face and roadway, roadway layout, gas extraction and exploitation, and efficiency of caving, etc.

Nuclear assay of coal. Volume 6. Mass flow devices for coal handling

International Nuclear Information System (INIS)

Anon.

1979-01-01

The mass of coal entering the boiler per unit time is an essential parameter for determinig the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

Measurements and simulation for design optimization for low NOx coal-firing system

Energy Technology Data Exchange (ETDEWEB)

E. Bar-Ziv; Y. Yasur; B. Chudnovsky; L. Levin; A. Talanker [Ben-Gurion University of Negev, Beer-Sheva (Israel)

2003-07-01

The information required to design a utility steam generator is the heat balance, fuel analysis and emission. These establish the furnace wall configuration, the heat release rates, and the firing technology. The furnace must be sized for (1) residence time for complete combustion with low NOx, and (2) reduction of flue gas temperature to minimize ash deposition. To meet these, computational fluid dynamics (CFD) of the combustion process in the furnace were performed and proven to be a powerful tool for this purpose. Still, reliable numerical simulations require careful interpretation and comparison with measurements. We report numerical results and measurements for a 575 MW pulverized coal tangential firing boiler of the Hadera power plant of Israel Electric Corporation (IEC). Measured and calculated values were found to be in reasonable agreement. We used the simulations for optimization and investigated temperature distribution, heat fluxes and concentration of chemical species. We optimized both the furnace flue gas temperature entering the convective path and the staged residence time for low NOx. We tested mass flow rates through close-coupled and separate overfire air ports and its arrangement and the coal powder fineness. These parameters can control the mixing rate between the fuel and the oxidizer streams and can affect the most important characteristics of the boiler such as temperature regimes, coal burning rate and nitrogen oxidation/reduction. From this effort, IEC started to improve the boiler performance by replacing the existing typical tangential burners to low NOx firing system to ensure the current regulation requirements of emission pollutions.

The relation between district raise in the multiple coal seams and its pillars

Energy Technology Data Exchange (ETDEWEB)

Zhai, X. [Jiaozuo Institute of Technology, Jiaozuo (China). Dept. of Mining Engineering

2002-02-01

Based on the geological condition of multiple coal seams mining in No.8 Colliery of Pingdingshan Coal Group, the behaviours of the front abutment pressure in each of the coal seams and the fixed abutment pressure are observed. The main cause of deformation and damage to the galleries is the increasing value of the valid load coefficient of the surrounding rock. The rational pillar width of the district raise is studied when its two side seams have been mined, and the layout question of district raise in the different set of seams is also studied. The conclusions derived from the study are useful guiding reference for the design of district raise layout in deep multiple coal seams mining. 6 refs., 3 figs., 1 tab.

The peculiarities of structurizing enclosing rock massif while developing a coal seam

Science.gov (United States)

Kozyreva, E. N.; Shinkevich, M. V.

2017-09-01

Different concepts of the development of geo-mechanical processes during longwall mining of a seam which are fundamentally different from the conventional ones are introduced in the article. Fundamental principles of the model for structurizing enclosing rock mass while longwall mining along the strike are described. The model was developed on the bases of non-linear geomechanical laws. According to the model, rock mass in the area of mining operation is organized as rock geomechanical layers with shifting arches. And the formation period of shifting arches in disintegrated rock mass is divisible by the length of the stope. Undulate characteristic of a massif as a peculiarity of man-made structurization of a massif is defined. It is shown that structuring the broken massif causes the formation of block-structured system and it can be detected while monitoring the ground pressure in powered support props. The results of the research allow decreasing the negative influence of a ground pressure and can be applied to specify parameters for controlling the roof, defining geometrical dimensions of a mining section and positioning of holing chute (face entry).

Radioactivity of dumps in mining areas of the Upper Silesian Coal Basin in Poland

Directory of Open Access Journals (Sweden)

Dorda J.

2012-04-01

Full Text Available Underground coal mining is associated with large quantities of gangue. In the past, the majority of gangue was not utilized but was placed in the vicinity of the coalmines forming cone-shaped dumps. Some of them contained even millions of tons of rock. Nowadays, environmental precautions extort larger utilization of any kind of waste materials, for example in road construction, civil engineering or as stowing in underground abandoned workings. Examination of the composition of waste dumps, including radioactivity, is thus an important issue. The paper presents results of a radiological survey carried out in several dumps located in the Upper Silesian Coal Basin in the south of Poland. Measurements of samples were carried out with the use of a gamma-ray spectrometer. Activity concentration results for the uranium and thorium decay chains are discussed.

The Applicability of Different Fluid Media to Measure Effective Stress Coefficient for Rock Permeability

Directory of Open Access Journals (Sweden)

Ying Wang

2015-01-01

Full Text Available Effective stress coefficient for permeability (ESCK is the key parameter to evaluate the properties of reservoir stress sensitivity. So far, little studies have clarified which ESCK is correct for a certain reservoir while rock ESCK is measured differently by different fluid media. Thus, three different fluids were taken to measure a fine sandstone sample’s ESCK, respectively. As a result, the ESCK was measured to be the smallest by injecting nitrogen, the largest by injecting water, and between the two by brine. Besides, those microcharacteristics such as rock component, clay mineral content, and pore structure were further analyzed based on some microscopic experiments. Rock elastic modulus was reduced when water-sensitive clay minerals were encountered with aqua fluid media so as to enlarge the rock ESCK value. Moreover, some clay minerals reacting with water can spall and possibly block pore throats. Compared with water, brine can soften the water sensitivity; however, gas has no water sensitivity effects. Therefore, to choose which fluid medium to measure reservoir ESCK is mainly depending on its own exploitation conditions. For gas reservoirs using gas to measure ESCK is more reliable than water or brine, while using brine is more appropriate for oil reservoirs.

Permeability Measurements of Rock Samples from Conduit Drilling at Unzen Volcano, Japan

Science.gov (United States)

Watanabe, T.; Shimizu, Y.; Noguchi, S.; Nakada, S.

2006-12-01

The last eruption of Unzen Volcano (1990-1995) was effusive to form lava domes, though magmas at depths are estimated to have contained volatile materials enough to cause explosive eruptions [e.g., Sato et al., 1995]. Most of volatile materials should have escaped from ascending magmas. The escape of gas is controlled by permeability of magmas and country rocks. Unzen Scientific Drilling Project sampled both the latest conduit and its country rock (USDP-4). In order to understand degassing processes, we have measured the permeability of these rock samples. Four cube samples with edges of 25 mm were cut from USDP-4 cores C1, C12 (country rock), C13 and C14 (conduit). Sample C1 is considered as Old Unzen Lava, and Sample C12 volcanic breccia. The transient pulse method was employed to measure the permeability. It applies a step of the fluid pressure difference across a specimen, and measures the decay rate of the fluid pressure difference. This method can be applied to samples with very low permeability, since it determines the permeability without measuring the fluid flux. Nitrogen gas was used as a pore fluid. Our permeametry system is built in a pressure vessel, and the confining pressure and the pore fluid pressure can be controlled independently. The temperature of the measurement system is kept constant within 0.1 degree. The temperature control and the background leak rate limit the measurable permeability to be higher than 10^{-20} m2. Measurements were first conducted under the atmospheric pressure. The permeability in a rock sample varies with the direction by a factor less than 5. Sample C1 has the lowest permeability (10^{-19} m2), and Sample C12 the highest value (10^{-17 m2). The permeability of C13 and C14 is of the order of 10^{- 18} m2. Though only a trace of vesicles can be seen in conduit samples, the interconnection is still maintained. The pressure dependence of the permeability is now investigated up to 50 MPa. The permeability of C13 and C14

Application of proving-ring technology to measure thermally induced displacements in large boreholes in rock

International Nuclear Information System (INIS)

Patrick, W.C.; Reactor, N.L.; Butkovich, T.R.

1984-03-01

A strain-gauged proving-ring transducer was designed and deployed to measure small diametral displacements in 0.61-m diameter boreholes in rock. The rock surrounding the boreholes was previously heated by storage of spent nuclear fuel assemblies and measurements during post-retrieval cooling of the rock were made. To accomplish this, a transducer was designed to measure displacements in the range of 10 to 100 μm, to function in a time-varying temperature regime of 30 0 to 60 0 C at a relative humidity of 100%, to be of low stiffness, and to be easily and quickly installed. 7 references, 6 figures, 1 table

Method of predicting air pollution of coal mines with use of new synthetic materials

Energy Technology Data Exchange (ETDEWEB)

Sukhanov, V V; Putilina, O.N.

1988-08-01

Presents a methodological approach that enables on the basis of laboratory experiment to give a hygienic evaluation of synthetic materials used in coal mines to harden coal and rock masses to prevent rock falls and caving and for hermetization of ventilation equipment. Polyurethane, carbamidoformaldehyde and phenolformaldehyde plastic foam are studied in an experiment tha examined quantitative emission ofsubstances from their original components in the process of forming contaminants. Synthetics in a beaker are placed in an exsiccator, mixed with air, samples of volatiles particles collected and dynamics of their emission are calculated using regression and linear equations. Amounts of 2,4- toluenediisocyanate and diethylamine produced by polyurethane, and formaldehyde and methanol from carbamidoformaldehyde did not exceed limits of maximum concentrations; phenolformaldehyde plastic foam produced amounts of phenols and formaldehydes that are significantly higher than maximal permissible concentrations. Laboratory procedure and use of formulae were confirmed by testing air in a Donetsugol' mine. Polyurethane and carbamidoformaldehyde didnot contaminate air above hygienically safe limits, while phenolformaldehyde plastic foam exceeded safety limits proving need for hygienic measures to protect miners from its contaminants. Adequacy of laboratory-mathematical method to evaluate emissions of harmful chemicals from resins under mining conditions shows value of laboratory testing of many resins for safety in mine use. 4 refs.

Slagging behavior of upgraded brown coal and bituminous coal in 145 MW practical coal combustion boiler

Energy Technology Data Exchange (ETDEWEB)

Akiyama, Katsuya; Pak, Haeyang; Takubo, Yoji [Kobe Steel, Ltd, Kobe (Japan). Mechanical Engineering Research Lab.; Tada, Toshiya [Kobe Steel, Ltd, Takasago (Japan). Coal and Energy Technology Dept.; Ueki, Yasuaki [Nagoya Univ. (Japan). Energy Science Div.; Yoshiie, Ryo; Naruse, Ichiro [Nagoya Univ. (Japan). Dept. of Mechanical Science and Engineering

2013-07-01

The purpose of this study is to quantitatively evaluate behaviors of ash deposition during combustion of Upgraded Brown Coal (UBC) and bituminous coal in a 145 MW practical coal combustion boiler. A blended coal consisting 20 wt% of the UBC and 80 wt% of the bituminous coal was burned for the combustion tests. Before the actual ash deposition tests, the molten slag fractions of ash calculated by chemical equilibrium calculations under the combustion condition was adopted as one of the indices to estimate the tendency of ash deposition. The calculation results showed that the molten slag fraction for UBC ash reached approximately 90% at 1,523 K. However, that for the blended coal ash became about 50%. These calculation results mean that blending the UBC with a bituminous coal played a role in decreasing the molten slag fraction. Next, the ash deposition tests were conducted, using a practical pulverized coal combustion boiler. A water-cooled stainless-steel tube was inserted in locations at 1,523 K in the boiler to measure the amount of ash deposits. The results showed that the mass of deposited ash for the blended coal increased and shape of the deposited ash particles on the tube became large and spherical. This is because the molten slag fraction in ash for the blended coal at 1,523 K increased and the surface of deposited ash became sticky. However, the mass of the deposited ash for the blended coal did not greatly increase and no slagging problems occurred for 8 days of boiler operation under the present blending conditions. Therefore, appropriate blending of the UBC with a bituminous coal enables the UBC to be used with a low ash melting point without any ash deposition problems in a practical boiler.

Empirical approach for designing of support system in mechanized coal pillar mining

Energy Technology Data Exchange (ETDEWEB)

Kushwaha, A.; Singh, S.K.; Tewari, S.; Sinha, A. [Central Institute of Mining & Fuel Research, Dhanbad (India)

2010-10-15

Mechanized room-and-pillar system of coal pillar mining using side dump loading machine or load haul dumper machine, or by continuous miner, is the presently most dominant under ground method of extraction in India. Under this method of extraction, strata control is a major problem affecting safety and productivity of the mine. As per existing Director General of Mine Safety guidelines, systematic support rules must be followed at the depillaring faces irrespective of immediate roof rock type and competency. Therefore, there is a high chance that sometimes these systematic support rules give unnecessarily high support, or sometimes inadequate support, which may lead to roof failure at the face. As a result, there is a big loss of life and material including coal in terms of left-outribs/stooks and other associated mining equipment deployed at the faces. Therefore, in the present paper, authors attempted to develop generalized empirical equations for estimating the required support load density at different places of the face based on geotechnical parameters of the mine and physico-mechanical properties of the immediate roof rocks for designing of support system during mechanized coal pillar mining.

Prediction of acid mine drainage generation potential of various lithologies using static tests: Etili coal mine (NW Turkey) as a case study.

Science.gov (United States)

Yucel, Deniz Sanliyuksel; Baba, Alper

2016-08-01

The Etili neighborhood in Can County (northwestern Turkey) has large reserves of coal and has been the site of many small- to medium-scale mining operations since the 1980s. Some of these have ceased working while others continue to operate. Once activities cease, the mining facilities and fields are usually abandoned without rehabilitation. The most significant environmental problem is acid mine drainage (AMD). This study was carried out to determine the acid generation potential of various lithological units in the Etili coal mine using static test methods. Seventeen samples were selected from areas with high acidic water concentrations: from different alteration zones belonging to volcanic rocks, from sedimentary rocks, and from coals and mine wastes. Static tests (paste pH, standard acid-base accounting, and net acid generation tests) were performed on these samples. The consistency of the static test results showed that oxidation of sulfide minerals, especially pyrite-which is widely found not only in the alteration zones of volcanic rocks but also in the coals and mine wastes-is the main factor controlling the generation of AMD in this mine. Lack of carbonate minerals in the region also increases the occurrence of AMD.

Clean coal technologies

International Nuclear Information System (INIS)

Bourillon, C.

1994-01-01

In 1993 more than 3.4 billion tonnes of coal was produced, of which half was used to generate over 44 per cent of the world's electricity. The use of coal - and of other fossil fuels- presents several environmental problems such as emissions of sulphur dioxide (SO 2 ), nitrogen oxides (NO 2 ), and carbon dioxide (CO 2 ) into the atmosphere. This article reviews the measures now available to mitigate the environmental impacts of coal. (author)

A Study of the Large Deformation Mechanism and Control Techniques for Deep Soft Rock Roadways

Directory of Open Access Journals (Sweden)

Xiaojie Yang

2018-04-01

Full Text Available Large deformation control of deep soft rock roadways has been a major problem in mining activities worldwide. This paper considers the supporting problem related to large deformation of a deep soft rock roadway in Chao’hua coal mine. The discrete element simulation method (UDEC software is adopted to simulate a tailgate of panel 31041 in Chao’hua coal mine. The failure patterns of unsupported and primary supported roadway are simulated, and these reveal the characteristics of deformation, stress and crack propagation. The excavation of roadway leads to high deviator stress, which exceeds the peak strength of shallow surrounding rock and causes it to enter the post-failure stage. Tensile failures then initiate and develop around the roadway, which causes the fragmentation, dilation and separation of shallow surrounding rock. The compressive capacity of the primary support system is low, which results in serious contraction in the full section of the roadway. An improved control scheme is put forward for the support of a tailgate. The underground test results confirm that the improved support system effectively controlled large deformation of the surrounding rocks, which can provide references for support in the design of roadways excavated in deep soft stratum.

Comparative Assessment to Danger of Rock Bursts Origin in Different Conditions of Mining in OKR

OpenAIRE

Bukovanský Stanislav

1998-01-01

For this comparative assessment to factual possibilities of balance failure it is necessary to investigate a character and possible changes in individual elements of the system "rock - time", as well as their mutual interaction with rock burst origin and their course. Research observations after burst show that the influence of strong energy after rock burst, into the overlying impact click is present in a coal seam due to its higher pressure to a face (when compared with a relevant pressure...

Rb-Sr measurements on metamorphic rocks from the Barro Alto Complex, Goias, Brazil

International Nuclear Information System (INIS)

Fuck, R.A.; Neves, B.B.B.; Cordani, U.G.; Kawashita, K.

1988-01-01

The Barro Alto Complex comprises a highly deformed and metamorphosed association of plutonic, volcanic, and sedimentary rocks exposed in a 150 x 25 Km boomerang-like strip in Central Goias, Brazil. It is the southernmost tip of an extensive yet discontinuous belt of granulite and amphibolite facies metamorphic rocks which include the Niquelandia and Cana Brava complexes to the north. Two rock associations are distinguished within the granulite belt. The first one comprises a sequence of fine-grained mafic granulite, hypersthene-quartz-feldspar granulite, garnet quartzite, sillimanite-garnet-cordierite gneiss, calc-silicate rock, and magnetite-rich iron formation. The second association comprises medium-to coarse-grained mafic rocks. The medium-grade rocks of the western/northern portion (Barro Alto Complex) comprise both layered mafic rocks and a volcanic-sedimentary sequence, deformed and metamorphosed under amphibolite facies conditions. The fine-grained amphibolite form the basal part of the Juscelandia meta volcanic-sedimentary sequence. A geochronologic investigation by the Rb-Sr method has been carried out mainly on felsic rocks from the granulite belt and gneisses of the Juscelandia sequence. The analytical results for the Juscelandia sequence are presented. Isotope results for rocks from different outcrops along the gneiss layer near Juscelandia are also presented. In conclusion, Rb-Sr isotope measurements suggest that the Barro Alto rocks have undergone at least one important metamorphic event during Middle Proterozoic times, around 1300 Ma ago. During that event volcanic and sedimentary rocks of the Juscelandia sequence, as well as the underlying gabbro-anorthosite layered complex, underwent deformation and recrystallization under amphibolite facies conditions. (author)

3D numerical modeling of longwall mining with top-coal caving

Energy Technology Data Exchange (ETDEWEB)

Yasitli, N.E.; Unver, B. [Hacettepe University, Ankara (Turkey). Dept. of Mining Engineering

2005-02-01

Top-coal caving is the key factor affecting the efficiency of production at thick-coal seams. During production of top coal by caving behind the face not only a significant amount of coal is lost in the goaf but the coal drawn by means of caving is diluted considerably with surrounding rock. Therefore, it is not possible to carry out an efficient production operation unless caving of top coal behind the face is optimized. In this paper, results of 3D modeling of the top-coal-caving mechanism by using the finite difference code FLAC3{sup D} at the M3 longwall panel of the Omerler Underground Mine located at Tuncbilek (Turkey) are presented. According to the modeling results, maximum vertical abutment stresses were formed at a distance of 7m in front of the face. An analysis of the conditions of top coal has revealed that a 1.5 m thick layer of coal just above the shield supports is well fractured. However, a 3.5 m thick layer of coal above the fractured part is either not fractured or is fractured in the form of large blocks leading to obstruction of windows of shields during coal drawing. It is concluded that, in order to decrease dilution and increase extraction ratio and efficiency of operation, top coal should be as uniformly fractured as possible. Hence, an efficient and continuous coal flowing behind the face can be maintained. A special pre-fracture blasting strategy just sufficient enough to form cracks in the top coal is suggested by means of comparing with the results of numerical modeling.

Trace elemental composition of Nigerian coal measured by neutron activation analysis

International Nuclear Information System (INIS)

Ndiokwere, Ch.L.; Guinn, V.P.; Burtner, D.

1983-01-01

The instrumental neutron activation analysis (INAA) technique has been used to determine 17 major, minor and trace elements in samples of the three major sources of Nigerian coal. The NBS Standard Reference Material, Coal SRM 1632, was also analyzed, for the purpose of verifying the accuracy of the method. The concentrations of the major elements determined for the Nigerian coal were found to be much lower than the mean values of those reported for coal samples from other parts of the world. (author)

Method of measuring material properties of rock in the wall of a borehole

Science.gov (United States)

Overmier, David K.

1985-01-01

To measure the modulus of elasticity of the rock in the wall of a borehole, a plug is cut in the borehole wall. The plug, its base attached to the surrounding rock, acts as a short column in response to applied forces. A loading piston is applied to the top of the plug and compression of the plug is measured as load is increased. Measurement of piston load and plug longitudinal deformation are made to determine the elastic modulus of the plug material. Poisson's ratio can be determined by simultaneous measurements of longitudinal and lateral deformation of the plug in response to loading. To determine shear modulus, the top of the plug is twisted while measurements are taken of torsional deformation.

Coal Fields and Federal Lands of the Conterminous United States

Science.gov (United States)

Biewick, Laura

1997-01-01

The map depicts the relationship of coal and public lands in the conterminous U. S. Multiple GIS layers are being created for the purpose of deriving estimates of how much coal is owned and administered by the Federal government. Federal coal areas have a profound effect on land-management decisions. Regulatory agencies attempt to balance energy development with alternative land-use and environmental concerns. A GIS database of Federal lands used in energy resource assessments is being developed by the U. S. Geological Survey (USGS) in cooperation with the U.S. Bureau of Land Management (BLM) to integrate information on status of public land, and minerals owned by the Federal government with geologic information on coal resources, other spatial data, coal quality characteristics, and coal availability for development. Using national-scale data we estimate that approximately 60 percent of the area underlain by coal-bearing rocks in the conterminous United States are under Federal surface. Coal produced from Federal leases has tripled from about 12 percent of the total U.S. production in 1976 to almost 34 percent in 1995 (Energy Information Administration website ftp://ftp.eia.doe.gov/pub/coal/cia_95_tables/t13p01.txt). The reason for this increase is demand for low-sulfur coal for use in power plants and the fact that large reserves of this low-sulfur coal are in the western interior U.S., where the Federal government owns the rights to most of the coal reserves. The map was created using Arc/Info 7.0.3 on a UNIX system. The HPGL2 plot file for this map is available from the USGS Energy Resource Surveys Team from http://energy.cr.usgs.gov:8080/energy/coal.html.

Coal in sub-Saharan-African countries undergoing desertification

Energy Technology Data Exchange (ETDEWEB)

Weaver, J.N.; Brownfield, M.E.; Bergin, M.J. (United States Geological Survey, Denver, CO (USA))

1990-01-01

Coal has been reported in 11 of the 16 sub-Saharan countries discussed in this appraisal: Mauritania, Senegal, Mali, Niger, Benin, Nigeria, Cameroon, Central African Republic, Sudan, Ethiopia, and Somalia. No coal occurrences have been reported in Gambia, Togo, Burkina, Chad, and Djibouti but coal may be present within these countries because neighbouring countries do contain coal-bearing rocks. Most of these countries are undergoing desertification. Destruction of forest and shrub lands for fuel is occurring at an increasing rate because of desertification and increasing energy demands. Part of the present and future energy needs of the sub-Saharan region could be met by use of indigenous coal and peat. Nine sedimentary basins have the potential of either coal and/or peat deposits of economic value: 1- Senegal Basin, 2- Taoudeni Basin and Gao Trough, 3- Niger Basin, 4- Chad Basin. 5- Chari Basin, 6- Benue Trough (Depression), 7- Sudan Trough, 8- Plateau and Rift Belt, and 9- Somali Basin. Niger and Nigeria are the only countries in sub-Saharan Africa in which coal is presently being mined as a fuel source for powerplants and domestic use. Peat occurs in the deltas, lower river, and interdunal basin areas of Senegal, Mauritania, and Sudan. The overall objective of these studies is to establish, within the sub-Saharan region, energy independent countries using indigeneous coal and peat resources. These resources have the potential to replace wood and wood charcoal as domestic fuel in the urban centres, as well as producing electrical and industrial energy, thus reducing expensive oil imports and decreasing the rate of deforestation. 31 refs., 16 figs., 1 tab.

Localized damage in soft rock: experiments with field measurement techniques

International Nuclear Information System (INIS)

Nguyen, T.L.

2011-01-01

The research presented in this thesis concerns, firstly, an experimental study on the process of fracture in uniaxial compression of rock samples containing narrow, rectilinear notches inclined with respect to the axis of loading. Secondly, we study the evolution of shear strain localisation towards fracturing and failure in specimens of the same materials with a particular geometry, involving two rounded notches. This geometry, inspired by the work of Meuwissen et al. (1998) for tension tests on metals, promotes the localisation of shear strain in simple compression before fracture. Two different materials were studied: a natural rock of volcanic origin (Neapolitan Tuff) and an artificial 'roc' (CPIR09). In the studies presented, three full-field measurement techniques have been employed in combination: (i) the Digital Image Correlation (DIC), for measurement of kinematic fields at a sample's surface; (ii)acoustic Emission measurements (AE) and AE source location, to follow the evolution of damage in samples during loading; (iii) X-ray tomography (pre-and post-mortem studies), to characterise preexisting defects and discontinuities in the specimens and to better understand the fracturing in 3D. (author)

Swelling behavior of several bituminous coals and their thermally treated coals

Energy Technology Data Exchange (ETDEWEB)

Shui, Heng-fu; Cao, Mei-xia; Wang, Zhi-cai [Anhui University of Technology, Maanshan (China). School of Chemistry & Chemical Engineering

2007-07-01

The swelling behavior in different solvents of 4 bituminous coals with different ranks and their residues from extraction by CS{sub 2}/NMP mixed solvent (l:1 in volume) were measured. The change in swelling property of the four coals thermally treated at different temperature was observed. The results show that the swelling ratio decreases with increasing rank of coal. For lower rank bituminous coals the swelling ratios in polar solvent are higher than those in non-polar solvent, and this difference decreases with increasing rank. The cross-linking densities of the four residues decrease, and the swelling ratios increase compared with those of raw coals. The swelling ratios of the four thermally treated coals under 150{sup o}C in CS{sub 2} increase, suggesting the decrease in crosslinking density of them. When the thermal treatment temperature increases to 240{sup o}C, the swelling rations of the other three coals in NMP and CS{sub 2} increase again except gas coal, demonstrating the further decrease in crosslinking density. This result is coincident with the extraction yield change in the mixed solvent of the thermally treated coal. For example, the extraction yield of lean coal treated at 240{sup o}C increases from 6.9% to 17.3%. FT-IR results show the removal of oxygen group of the thermally treated coals. This may explain the increase in swelling ratio and extraction yield in the mixed solvent of coal after thermal treatment. The cross-linking density of the thermally treated coal decreases because of the break of hydrogen bonds due to removal of C = 0 and -OH oxygen groups during the thermal treatment, resulting in the increases of swelling ratio and extraction yield in the mixed solvent of thermally treated coal compared with those of raw coal. 15 refs., 3 figs., 6 tabs.

Coal Transition in the Czech Republic. An historical case study for the project 'Coal Transitions: Research and Dialogue on the Future of Coal'

International Nuclear Information System (INIS)

Reckova, Dominika; Recka, Lukacs; Scasny, Milan

2017-01-01

This is one of the 6 country case-studies commissioned to collect experience on past coal transitions. The 6 countries are: Czech Republic, the Netherlands, Poland, Spain, UK, USA. Their role in the Coal Transitions project was to provide background information for a Synthesis Report for decision makers, and provide general lessons for national project teams to take into account in developing their coal transitions pathways for the future. Content: History of coal production and coal reserves; Key features of the Czech economy; Fuel mix in the Czech Republic 1990 - 2014; Key features of coal sector in the Czech Republic after 1990; The use of coal in the Czech Republic and its possible replacement: A. Coal as source of Electricity, B. Coal as Heating source, C. Non - energy coal use; The state role in the coal sector after 1990 - mining limits; Measures to ease transition: Phasing-out of mining activities, Rehabilitation of environmentally damaged land, Programmes financing the remediation of ecological damage, Remediation of environmental damage caused by mining; Future outlook; Lessons learned; References; Annex

Measured sections and analyses of uranium host rocks of the Dockum Group, New Mexico and Texas

International Nuclear Information System (INIS)

Dickson, R.E.; Drake, D.P.; Reese, T.J.

1977-02-01

This report presents 27 measured sections from the Dockum Group of Late Triassic age, in the southern High Plains of eastern New Mexico and northwestern Texas. Many of the measured sections are only partial; the intent in those cases was to measure the parts of sections that had prominent sandstone/conglomerate beds or that had uranium deposits. No attempt was made to relate rock color to a rock color chart; rock colors are therefore approximate. Modal analyses (by thin-section examination) of sandstone and conglomerate samples and gamma-ray spectrometric analyses of the samples are presented in appendices

Distribution and mode of occurrence of selenium in US coals

Science.gov (United States)

Coleman, L.; Bragg, L.J.; Finkelman, R.B.

1993-01-01

Selenium excess and deficiency have been established as the cause of various health problems in man and animals. Combustion of fossil fuels, especially coal, may be a major source of the anthropogenic introduction of selenium in the environment. Coal is enriched in selenium relative to selenium's concentration in most other rocks and relative to selenium in the Earth's crust. Data from almost 9,000 coal samples have been used to determine the concentration and distribution of selenium in US coals. The geometric mean concentration of selenium in US coal is 1.7 ppm. The highest mean selenium value (geometric mean 4.7 ppm) is in the Texas Region. Atlantic Coast (Virginia and North Carolina) and Alaska coals have the lowest geometric means (0.2 and 0.42 ppm, respectively). All western coal regions have mean selenium concentrations of less than 2.0 ppm. In contrast, all coal basins east of the Rocky Mountains (except for several small basins in Rhode Island, Virginia, and North Carolina) have mean selenium values of 1.9 or greater. Generally, variations in selenium concentration do not correlate with variations in ash yield, pyritic sulphur, or organic sulphur concentrations. This may be the result of multiple sources of selenium; however, in some non-marine basins with restricted sources of selenium, selenium has positive correlations with other coal quality parameters. Selenium occurs in several forms in coal but appears to be chiefly associated with the organic fraction, probably substituting for organic sulphur. Other important forms of selenium in coal are selenium-bearing pyrite, selenium-bearing galena, and lead selenide (clausthalite). Water-soluble and ion-exchangeable selenium also have been reported. ?? 1993 Copyright Science and Technology Letters.

On the measurment of specific energy of coals by means of 12C determination using a correlation method

International Nuclear Information System (INIS)

Cywicka-Jakiel, T.; Bogacz, J.; Czubek, J.A.; Dabrowski, J.M.; Loskiewicz, J.; Zazula, J.M.

1982-01-01

The most important industrial property of coal is its gross specific energy (combustion heat). It depends mainly on carbon concentration in coal. We propose to measure the carbon or more precisely, its 12 C content using the (n,n'γ) reaction in which 4.43 MeV gamma rays are emitted. We are using the correlation technique which can be used in high background measurements. The idea of correlation type measurement necessitates the existence of a reaction chain with primary and secondary radiations emitted and registered. By measuring the correlation or covariance function PHI we can obtain a measure of the number of excited 12 C nuclei i.e. a value which is connected to the carbon concentration. The dependence of PHI/t ratio (t being the sampling interval time) on carbon concentration shows a clear increase of the PHI/t value with carbon content. The relative standard deviations for different points vary from 1.3 to 4.4%. The preliminary results presented show that with improved experimental techniques this method can find application in industrial coal cobustion heat measurements. (author)

Catastrophic dispersion of coal fly ash into oceans during the latest Permian extinction

Energy Technology Data Exchange (ETDEWEB)

Grasby, S.E.; Sanei, H.; Beauchamp, B. [Geological Survey Canada Calgary, Calgary, AB (Canada)

2011-02-15

During the latest Permian extinction about 250 Myr ago, more than 90% of marine species went extinct, and biogeochemical cycles were disrupted globally. The cause of the disruption is unclear, but a link between the eruption of the Siberian Trap flood basalts and the extinction has been suggested on the basis of the rough coincidence of the two events. The flood basalt volcanism released CO{sub 2}. In addition, related thermal metamorphism of Siberian coal measures and organic-rich shales led to the emission of methane, which would have affected global climate and carbon cycling, according to model simulations. This scenario is supported by evidence for volcanic eruptions and gas release in the Siberian Tunguska Basin, but direct indicators of coal combustion have not been detected. Here we present analyses of terrestrial carbon in marine sediments that suggest a substantial amount of char was deposited in Permian aged rocks from the Canadian High Arctic immediately before the mass extinction. Based on the geochemistry and petrology of the char, we propose that the char was derived from the combustion of Siberian coal and organic-rich sediments by flood basalts, which was then dispersed globally. The char is remarkably similar to modern coal fly ash, which can create toxic aquatic conditions when released as slurries. We therefore speculate that the global distribution of ash could have created toxic marine conditions.

A REAL-TIME COAL CONTENT/ORE GRADE (C2OC) SENSOR

Energy Technology Data Exchange (ETDEWEB)

Rand Swanson

2005-04-01

This is the final report of a three year DOE funded project titled ''A real-time coal content/ore grade (C{sub 2}OG) sensor''. The sensor, which is based on hyperspectral imaging technology, was designed to give a machine vision assay of ore or coal. Sensors were designed and built at Resonon, Inc., and then deployed at the Stillwater Mining Company core room in southcentral Montana for analyzing platinum/palladium ore and at the Montana Tech Spectroscopy Lab for analyzing coal and other materials. The Stillwater sensor imaged 91' of core and analyzed this data for surface sulfides which are considered to be pathfinder minerals for platinum/palladium at this mine. Our results indicate that the sensor could deliver a relative ore grade provided tool markings and iron oxidation were kept to a minimum. Coal, talc, and titanium sponge samples were also imaged and analyzed for content and grade with promising results. This research has led directly to a DOE SBIR Phase II award for Resonon to develop a down-hole imaging spectrometer based on the same imaging technology used in the Stillwater core room C{sub 2}OG sensor. The Stillwater Mining Company has estimated that this type of imaging system could lead to a 10% reduction in waste rock from their mine and provide a $650,000 benefit per year. The proposed system may also lead to an additional 10% of ore tonnage, which would provide a total economic benefit of more than $3.1 million per year. If this benefit could be realized on other metal ores for which the proposed technology is suitable, the possible economic benefits to U.S. mines is over $70 million per year. In addition to these currently lost economic benefits, there are also major energy losses from mining waste rock and environmental impacts from mining, processing, and disposing of waste rock.

Extreme coal handling

Energy Technology Data Exchange (ETDEWEB)

Bradbury, S; Homleid, D. [Air Control Science Inc. (United States)

2004-04-01

Within the journals 'Focus on O & M' is a short article describing modifications to coal handling systems at Eielson Air Force Base near Fairbanks, Alaska, which is supplied with power and heat from a subbituminous coal-fired central plant. Measures to reduce dust include addition of an enclosed recirculation chamber at each transfer point and new chute designs to reduce coal velocity, turbulence, and induced air. The modifications were developed by Air Control Science (ACS). 7 figs., 1 tab.

Analysing the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau

Directory of Open Access Journals (Sweden)

Wei Cao

2017-09-01

Full Text Available The coal mining has brought a series of ecological problems and environmental problems in permafrost regions. Taking Muli coal-mining area as an example, this article attempts to analyse the environmental harms caused by coal mining and its protection measures in permafrost regions of Qinghai–Tibet Plateau. This article analyses the influence of open mining on the surrounding permafrost around the open pit by using the numerical simulation. The results show that (1 based on the interrelation between coal mining and permafrost environment, these main environmental harm include the permafrost change and the natural environment change in cold regions; (2 once the surface temperature rises due to open mining, the permafrost will disappear with the increase of exploitation life. If considering the solar radiation, the climate conditions and the geological condition around the pit edge, the maximum thaw depth will be more than 2 m; (3 the protection measures are proposed to avoid the disadvantage impact on the permafrost environment caused by coal mining. It will provide a scientific basis for the resource development and environment protection in cold regions.

Distribution of base rock depth estimated from Rayleigh wave measurement by forced vibration tests

International Nuclear Information System (INIS)

Hiroshi Hibino; Toshiro Maeda; Chiaki Yoshimura; Yasuo Uchiyama

2005-01-01

This paper shows an application of Rayleigh wave methods to a real site, which was performed to determine spatial distribution of base rock depth from the ground surface. At a certain site in Sagami Plain in Japan, the base rock depth from surface is assumed to be distributed up to 10 m according to boring investigation. Possible accuracy of the base rock depth distribution has been needed for the pile design and construction. In order to measure Rayleigh wave phase velocity, forced vibration tests were conducted with a 500 N vertical shaker and linear arrays of three vertical sensors situated at several points in two zones around the edges of the site. Then, inversion analysis was carried out for soil profile by genetic algorithm, simulating measured Rayleigh wave phase velocity with the computed counterpart. Distribution of the base rock depth inverted from the analysis was consistent with the roughly estimated inclination of the base rock obtained from the boring tests, that is, the base rock is shallow around edge of the site and gradually inclines towards the center of the site. By the inversion analysis, the depth of base rock was determined as from 5 m to 6 m in the edge of the site, 10 m in the center of the site. The determined distribution of the base rock depth by this method showed good agreement on most of the points where boring investigation were performed. As a result, it was confirmed that the forced vibration tests on the ground by Rayleigh wave methods can be useful as the practical technique for estimating surface soil profiles to a depth of up to 10 m. (authors)

Experiments on rocks under high pressure conditions in GTA 20-32 triaxial press

Czech Academy of Sciences Publication Activity Database

Poláček, J.; Kožušníková, Alena

2012-01-01

Roč. 58, č. 1 (2012), s. 9-16 ISSN 1802-5420 Institutional support: RVO:68145535 Keywords : triaxial stress * deformation * rocks Subject RIV: DH - Mining, incl. Coal Mining http://gse.vsb.cz/2012/LVIII-2012-1-09-16.pdf

Law of Strata Pressure Behavior in Shallow Coal Seam

Science.gov (United States)

Zhao, Jian; Liu, Leibin; Zheng, Zhiyang

2018-02-01

The law of strata pressure behavior in shallow coal seam is analyzed, according to the load data of Jinjie Coal Mine 31109 working face hydraulic supports. The first weighting distance of main roof is 80 m, and the periodic weighting distance of main roof is about 20 m. And according to the load data in the middle and both ends of the working face, the working resistance of hydraulic supports and the setting load are a bit small, so they couldn’t meet the needs of supporting roof. Then, the front abutment pressure of working face is analyzed by numerical simulation. It does not only explain the reason that the load is too big, but also explains the reason that the strata pressure behavior in shallow coal seam is serious. The length of undamaged main roof rock beam verifies the correctness of the periodic weighting distance.

Synchronized droplet size measurements for Coal-Water-Slurry (CWS) diesel sprays of an electronically-controlled fuel injection system

Science.gov (United States)

Kihm, K. D.; Terracina, D. P.; Payne, S. E.; Caton, J. A.

Experiments were completed to study intermittent coal-water slurry (CWS) fuel sprays injected from an electronically-controlled accumulator injector system. A laser diffraction particle analyzing (LDPA) technique was used to measure the spray diameters (Sauter mean diameter, SMD) assuming the Rosin-Rammler two parameter model. In order to ensure an accurate synchronization of the measurement with the intermittent sprays, a new synchronization technique was developed using the light extinction signal as a triggering source for the data taking initiation. This technique allowed measurement of SMD's near the spray tip where the light extinction was low and the data were free from the multiscattering bias. Coal-water slurry fuel with 50% coal loading in mass containing 5 (mu)m mass median diameter coal particulates was considered. Injection pressures ranging from 28 to 110 MPa, two different nozzle orifice diameters, 0.2 ad 0.4 mm, and four axial measurement locations from 60 to 120 mm from the nozzle orifice were studied. Measurements were made for pressurized (2.0 MPa in gauge) and for ambient chamber conditions. The spray SMD showed an increase with the distance of the axial measurement location and with the ambient gas density, and showed a decrease with increasing injection pressure. A correlation of the Sauter mean diameter with the injection conditions was determined. The results were also compared with previous SMD correlations that were available only for diesel fuel sprays.

Repeated Geophysical Surface Measurements to Estimate the Dynamics of Underground Coalfires

Science.gov (United States)

Wuttke, M. W.; Kessels, W.; Han, J.; Halisch, M.; Rüter, H.; Lindner, H.

2009-04-01

Spontaneous combustion of coal has become a world wide problem caused by and affecting technical operations in coal mining areas. The localization of the burning centre is a prerequisite for any planning of fire fighting operations. For the German - Chinese coal fire project sponsored by the German Ministry of Science and Technologies (Grant No. 0330490K) two firezones, namely the so called fire zone 18 of the coal mining area of Wuda (Inner Mongolia, PR China) and the firezone of Queergou (Xinjiang, PR China) are currently monitored by geophysical measurements. For the geothermal and geochemical mapping 25 up to 1m deep boreholes with a diameter of approx. 30 mm are distributed over the particular firezone. To avoid highly dynamic gas flow processes in fire induced fractures caused by weather conditions, all boreholes were situated in the undisturbed rock compartments. In these boreholes, plastic tubes of 12 mm diameter provide access to the borehole ground filled with highly permeable gravel. The boreholes are otherwise sealed by clay. The geothermal observations consist of measurements of temperature profiles in the boreholes and thermal conductivity measurement on rock samples in the lab. The derived heat flow with maximum values of 80 W/m2 (Wuda) is more than three orders of magnitude higher than the natural undisturbed heat flow. The high heat flow suggests that the dominant heat transport is gas convection through the system of porous rock and fractures. The geochemical soil gas probing is performed by gas extraction from the boreholes. Measured are the concentrations of O2, CO, CO2, H2S and CH4. The O2 deficit in the soil air and the concentrations of the other combustion products compared to the concentrations in the free atmosphere are related to the combustion area. A magnetic mapping has only been performed in Wuda with point distances of 2 m and profile-distances of 3 to 4 m covered an area of 350  300m with 7913 points. The detected anomalies lie

Second generation of conical strain gauge probe for stress measurement in rock massif

Czech Academy of Sciences Publication Activity Database

Knejzlík, Jaromír; Rambouský, Zdeněk; Souček, Kamil; Staš, Lubomír

2008-01-01

Roč. 5, č. 3 (2008), s. 1-9 ISSN 1214-9705 R&D Projects: GA ČR(CZ) GA105/06/1768 Institutional research plan: CEZ:AV0Z30860518 Keywords : stress measurement * over - coring Subject RIV: DH - Mining, incl. Coal Mining

Thermal maturity patterns in Pennsylvanian coal-bearing rocks in Alabama, Tennessee, Kentucky, Virginia, West Virginia, Ohio, Maryland, and Pennsylvania: Chapter F.2 in Coal and petroleum resources in the Appalachian basin: distribution, geologic framework, and geochemical character

Science.gov (United States)

Ruppert, Leslie F.; Trippi, Michael H.; Hower, James C.; Grady, William C.; Levine, Jeffrey R.; Ruppert, Leslie F.; Ryder, Robert T.

2014-01-01

Thermal maturation patterns of Pennsylvanian strata in the Appalachian basin and part of the Black Warrior basin were determined by compiling previously published and unpublished percent-vitrinite-reflectance (%R0) measurements and preparing isograd maps on the basis of the measurements. The isograd values range from 0.6 %R0 in Ohio and the western side of the Eastern Kentucky coal field to 5.5 %R0 in the Southern field in the Pennsylvania Anthracite region, Schuylkill County, Pa. The vitrinite-reflectance values correspond to the American Society of Testing Materials (ASTM) coal-rank classes of high-volatile C bituminous to meta-anthracite, respectively. In general, the isograds show that thermal maturity patterns of Pennsylvanian coals within the Appalachian basin generally decrease from east to west. In the Black Warrior basin of Alabama, the isograds show a circular pattern with the highest values (greater than 1.6 %R0) centered in Jefferson County, Ala. Most of the observed patterns can be explained by variations in the depth of burial, variations in geothermal gradient, or a combination of both; however, there are at least four areas of higher ranking coal in the Appalachian basin that are difficult to explain by these two processes alone: (1) a set of west- to northwest-trending salients centered in Somerset, Cambria, and Fayette Counties, Pa.; (2) an elliptically shaped, northeast-trending area centered in southern West Virginia and western Virginia; (3) the Pennsylvania Anthracite region in eastern Pennsylvania; and (4) the eastern part of the Black Warrior coal field in Alabama. The areas of high-ranking coal in southwestern Pennsylvania, the Black Warrior coal field, and the Pennsylvania Anthracite region are interpreted here to represent areas of higher paleo-heat flow related to syntectonic movement of hot fluids towards the foreland associated with Alleghanian deformation. In addition to the higher heat flow from these fluids, the Pennsylvania

Application of rock mechanics in opencast mining

Energy Technology Data Exchange (ETDEWEB)

Desurmont, M; Feuga, B

1979-07-01

The significance of opencast mining in the world today is mentioned. With the exception of coal, opencast workings provide approximately 80% of output. The importance of opencast has continued to increase over the last ten years. Access to the mineral usually necessitates the removal of large quantities of rock. The aim is to reduce the quantity of the latter as much as possible in order to minimize the dirt/mineral ratio. For this purpose use has been made of the operating techniques of rock mechanics in order to determine the optimum dimensions of the access trench compatible with safety requirements. The author illustrates this technique by means of three examples: the Luzenac talc workings, the Mont-Roc fluorine workings and the Big Hole at Kimberley.

Dust control in Belgian coal mines. Position at the beginning of 1975

Energy Technology Data Exchange (ETDEWEB)

Preat, B; Vanstraelen, M

1975-01-01

A general view is given of dust control in Belgian coal mines at the beginning of 1975. The statistical data received from the mines are presented in tabular form. The length and the output of coal faces treated by the classical methods of pre-spraying of the wall, wet cutting, water infusion and wet pneumatic picks are given separately; in some cases two or more of these techniques are used together on the same coalface. The number of rock headings in which different methods of dust control are used is also given.

International Coal Report's coal year 1991

Energy Technology Data Exchange (ETDEWEB)

McCloskey, G [ed.

1991-05-31

Following introductory articles on factors affecting trade in coal and developments in the freight market, tables are given for coal exports and coal imports for major countries worldwide for 1989 and 1990. Figures are also included for coal consumption in Canada and the Eastern bloc,, power station consumption in Japan, coal supply and demand in the UK, electric utility coal consumption and stocks in the USA, coal production in Australia, Canada and USA by state, and world hard coal production. A final section gives electricity production and hard coal deliveries in the EEC, sales of imported and local coal and world production of pig iron and steel.

Advances in coalbed methane reservoirs using integrated reservoir characterization and hydraulic fracturing in Karaganda coal basin, Kazakhstan

Science.gov (United States)

Ivakhnenko, Aleksandr; Aimukhan, Adina; Kenshimova, Aida; Mullagaliyev, Fandus; Akbarov, Erlan; Mullagaliyeva, Lylia; Kabirova, Svetlana; Almukhametov, Azamat

2017-04-01

Coalbed methane from Karaganda coal basin is considered to be an unconventional source of energy for the Central and Eastern parts of Kazakhstan. These regions are situated far away from the main traditional sources of oil and gas related to Precaspian petroleum basin. Coalbed methane fields in Karaganda coal basin are characterized by geological and structural complexity. Majority of production zones were characterized by high methane content and extremely low coal permeability. The coal reservoirs also contained a considerable natural system of primary, secondary, and tertiary fractures that were usually capable to accommodate passing fluid during hydraulic fracturing process. However, after closing was often observed coal formation damage including the loss of fluids, migration of fines and higher pressures required to treat formation than were expected. Unusual or less expected reservoir characteristics and values of properties of the coal reservoir might be the cause of the unusual occurred patterns in obtained fracturing, such as lithological peculiarities, rock mechanical properties and previous natural fracture systems in the coals. Based on these properties we found that during the drilling and fracturing of the coal-induced fractures have great sensitivity to complex reservoir lithology and stress profiles, as well as changes of those stresses. In order to have a successful program of hydraulic fracturing and avoid unnecessary fracturing anomalies we applied integrated reservoir characterization to monitor key parameters. In addition to logging data, core sample analysis was applied for coalbed methane reservoirs to observe dependence tiny lithological variations through the magnetic susceptibility values and their relation to permeability together with expected principal stress. The values of magnetic susceptibility were measured by the core logging sensor, which is equipped with the probe that provides volume magnetic susceptibility parameters

Using Resistivity Measurements to Determine Anisotropy in Soil and Weathered Rock

Directory of Open Access Journals (Sweden)

S. Soto-Caban

2013-08-01

Full Text Available This study uses electrical resistivity measurements of soils and weathered rock to perform a fast and reliable evaluation of field anisotropy. Two test sites at New Concord, Ohio were used for the study. These sites are characterized by different landform and slightly east dipping limestone and siltstone formations of Pennsylvanian age. The measured resistivity ranged from 19 Ω∙m to 100 ��∙m, and varied with depth, landform, and season. The anisotropy was determined by a comparison of resistance values along the directions of strike and the dip. Measurements showed that the orientation of electrical anisotropy in the shallow ground may vary due to fluid connection, which is determined by the pore geometry in soil and rock, as well as by the direction of fluid movement. Results from this study indicated that a portable electrical resistivity meter is sensitive and reliable enough to be used for shallow ground fluid monitoring.

Study of Natural Radioactivity in Coal Samples of Baganuur Coal Mine, Mongolia

Science.gov (United States)

Altangerel, M.; Norov, N.; Altangerel, D.

2009-03-01

Coal and soil samples from Baganuur Coal Mine (BCM) of Mongolia have been investigated. The activities of 226Ra, 232Th and 40K have been measured by gamma-ray spectrometry using shielded HPGe detector. Contents of natural radionuclide elements (U, Th and K) have been determined. Also the activities and contents of radionuclide of ashes were determined which generated in Thermal Power Plant ♯3 of Ulaanbaatar from coal supplied from BCM.

Co-firing straw and coal in a 150-MWe utility boiler: in situ measurements

DEFF Research Database (Denmark)

Hansen, P. F.B.; Andersen, Karin Hedebo; Wieck-Hansen, K.

1998-01-01

A 2-year demonstration program is carried out by the Danish utility I/S Midtkraft at a 150-MWe PF-boiler unit reconstructed for co-firing straw and coal. As a part of the demonstration program, a comprehensive in situ measurement campaign was conducted during the spring of 1996 in collaboration...... with the Technical University of Denmark. Six sample positions have been established between the upper part of the furnace and the economizer. The campaign included in situ sampling of deposits on water/air-cooled probes, sampling of fly ash, flue gas and gas phase alkali metal compounds, and aerosols as well...... deposition propensities and high temperature corrosion during co-combustion of straw and coal in PF-boilers. Danish full scale results from co-firing straw and coal, the test facility and test program, and the potential theoretical support from the Technical University of Denmark are presented in this paper...

Analysis on Filling Ratio and Shield Supporting Pressure for Overburden Movement Control in Coal Mining with Compacted Backfilling

Directory of Open Access Journals (Sweden)

Yanli Huang

2016-12-01

Full Text Available Since the weight of overburden is sustained by both the backfill body and the unmined solid coal in coal mining with compacted backfilling (CMCB panels, the stress and deformation characteristics of the surrounding rocks in coal mining are radically changed. The overburden movement control mechanism by coordinating with backfill body and shield in CMCB was studied systematically in this paper. Based on the analysis of deformational and structural characteristics of surrounding rock in CMCB panels, the methods of theoretical analysis, numerical simulation and engineering test are employed. The results show that the fracture of the main roof is mainly controlled by the filling ratio φ and is non-correlated to the shield supporting pressure p. However, p has a significant control effect on the deflection of roof within the shield canopy length, and adversely affects the filling ratio. With the increase of the filling ratio of the gob, the maximum sagging of the immediate and the main roofs, the peak front and the influence range of the abutment pressures are gradually reduced. Correspondingly, the stable period of internal pressure of backfill body in the gob is shortened. Engineering practice shows that the sagging of the gob roof, the distribution of the abutment pressure, the distribution of the internal pressure in the backfill body, and the ground surface sagging results obtained by the in-situ measurement are approximately corresponding to the theoretical analysis and numerical simulation results.

Temperature profiles of coal stockpiles

Energy Technology Data Exchange (ETDEWEB)

Sensogut, C.; Ozdeniz, A.H.; Gundogdu, I.B. [Dumlupinar University, Kutahya (Turkey). Mining Engineering Department

2008-07-01

Excess of produced coals should be kept in the stockyards of the collieries. The longer the duration time for these coals, the greater possibility for spontaneous combustion to take place. Spontaneously burnt coals result in economical and environmental problems. Therefore, taking the necessary precautions before an outburst of the spontaneous combustion phenomenon is too important in terms of its severe results. In this study, a stockpile having industrial dimensions was formed in coal stockyard. The effective parameters on the stockpiles of coal such as temperature and humidity of the weather, time, and atmospheric pressure values were measured. The interior temperature variations of these stockpiles caused by the atmospheric conditions were also measured. The interior temperature distribution maps of the stockpile together with maximum and minimum temperature values were expressed visually and numerically by the assistance of obtained data.

Stress analysis of longwall top coal caving

Energy Technology Data Exchange (ETDEWEB)

Alehossein, H.; Poulsen, B.A. [CSIRO Exploration & Mining, Brisbane, Qld. (Australia)

2010-01-15

Longwall top coal caving (LTCC) is a relatively new method of mining thick coal seams that is currently achieving high productivity and efficiency. The technique is similar to traditional longwall mining in that a cutting head slices coal from the lower section of the coal seam onto a conveyor belt installed in front of the hydraulic support near the cutting face. In modern LTCC an additional rear conveyor belt is located behind the support, to which the flow of the caved coal from the upper part of the seam can be controlled by a moveable flipper attached to the canopy of the support. The mining method relies on the fracturing of the top coal by the front abutment pressure to achieve satisfactory caving into the rear conveyor. This paper develops a yield and caveability criterion based on in situ conditions in the top coal in advance of the mining face (yield) and behind the supports (caveability). Yielding and caving effects are combined into one single number called caving number (CN), which is the multiplication result of caving factor (CF) and yield factor (YF). Analytical derivations are based on in situ stress conditions, Mohr-Coulomb and/or Hoek-Brown rock failure criteria and an on-associated elastoplastic strain softening material behaviour. The yield and caveability criteria are in agreement with results from both numerical studies and mine data. The caving number is normalised to mining conditions of a reference Chinese mine (LMX mine) and is used to assess LTCC performance at fourteen other Chinese working longwalls that have had varying success with the LTCC technology. As a predictive model, results of this analytical/numerical study are useful to assess the potential success of caving in new LTCC operations and in different mining conditions.

Nuclear assay of coal. Volume 6. Mass flow devices for coal handling. Final report

International Nuclear Information System (INIS)

Gozani, T.; Elias, E.; Bevan, R.

1980-04-01

The mass of coal entering the boiler per unit time is an essential parameter for determining the total rate of heat input. The mass flow rate of coal on a conveyor belt is generally determined as a product of the instantaneous mass of material on a short section of the belt and the belt velocity. Belt loading could be measured by conventional transducers incorporating mechanical or electromechanical weighers or by gamma-ray attenuation gauge. This report reviews the state of the art in mass flow devices for coal handling. The various methods are compared and commented upon. Special design issues are discussed relative to incorporating a mass flow measuring device in a Continuous On-Line Nuclear Analysis of Coal (CONAC) system

Tunnelling support methods and their possible application to machine rock face excavation in coal mining

Energy Technology Data Exchange (ETDEWEB)

Maidl, B.; Edeling, H.

1981-06-11

Mechanized pushing through the rocks is possible even in teary rock if protective measures are taken directly behind the drill bit. Present arch-type supports are best reinforced with sprayed concrete as it will take up rock deformations. In this case, however, the question soon arises whether arch-type steel supports should be used at all. So far, mature solutions have not been found but they will be possible if the mining industry is really interested. Sprayed concrete with admixtures of reinforcing steel fibers plays a major role here as it will protect miner's heads already at an early stage and is suitable as support even at a later stage. Equally interesting would be reinforced concrete pumped behind advancing formwork. A combination of both techniques may turn out to be the most suitable method to replace arch-type supports. A problem of particular importance is machine bracing in the fresh concrete lining. If the concrete is filled in directly behind the drill bit, it is only 4 to 6 h old when it reaches the bracing device, i.e., its pressure resistance is lower than the contact pressure of present mining machinery. It may be difficult to find a solution here but it is considered to be possible. With shell concrete, the formwork should be constructed so as to withstand the contact pressure.