WorldWideScience

Sample records for co2-ch4 mixture etude

  1. Studies on the adsorption behavior of CO2-CH4 mixtures using activated carbon

    Directory of Open Access Journals (Sweden)

    R. B. Rios

    2013-12-01

    Full Text Available Separation of CO2 from CO2-CH4 mixtures is an important issue in natural gas and biogas purification. The design of such separation processes depends on the knowledge of the behavior of multicomponent adsorption, particularly that of CO2-CH4 mixtures. In this study, we present a series of experimental binary equilibrium isotherms for CO2-CH4 mixtures on an activated carbon at 293 K and compare them with predicted values using the Ideal Adsorption Solution Theory (IAST and the Extended Langmuir (EL model. Even at concentrations of ca. 20% for all binary isotherms, CO2 already presents higher adsorbed amounts with respect to CH4. A maximum selectivity of around 8.7 was observed for a nearly equimolar mixture at 0.1 MPa. The IAST in conjunction with the Toth equation showed slightly better results than IAST using the Langmuir equation and both showed better results than the EL model.

  2. Adsorption kinetics of CO2, CH4, and their equimolar mixture on coal from the Black Warrior Basin, West-Central Alabama

    Science.gov (United States)

    Gruszkiewicz, M.S.; Naney, M.T.; Blencoe, J.G.; Cole, D.R.; Pashin, J.C.; Carroll, R.E.

    2009-01-01

    Laboratory experiments were conducted to investigate the adsorption kinetic behavior of pure and mixed gases (CO2, CH4, approximately equimolar CO2 + CH4 mixtures, and He) on a coal sample obtained from the Black Warrior Basin at the Littleton Mine (Twin Pine Coal Company), Jefferson County, west-central Alabama. The sample was from the Mary Lee coal zone of the Pottsville Formation (Lower Pennsylvanian). Experiments with three size fractions (45-150????m, 1-2??mm, and 5-10??mm) of crushed coal were performed at 40????C and 35????C over a pressure range of 1.4-6.9??MPa to simulate coalbed methane reservoir conditions in the Black Warrior Basin and provide data relevant for enhanced coalbed methane recovery operations. The following key observations were made: (1) CO2 adsorption on both dry and water-saturated coal is much more rapid than CH4 adsorption; (2) water saturation decreases the rates of CO2 and CH4 adsorption on coal surfaces, but it appears to have minimal effects on the final magnitude of CO2 or CH4 adsorption if the coal is not previously exposed to CO2; (3) retention of adsorbed CO2 on coal surfaces is significant even with extreme pressure cycling; and (4) adsorption is significantly faster for the 45-150????m size fraction compared to the two coarser fractions. ?? 2008 Elsevier B.V.

  3. Effect of Amine-Functionalized MIL-53 Metal Organic Frameworks on the Performance of Poly(4-methyl-1-pentyne Membrane in CO2/CH4 Separation Gas Mixture

    Directory of Open Access Journals (Sweden)

    Reza Abedini

    2015-06-01

    Full Text Available The effect of NH2-MIL 53 metal organic framework (MOF on gas transport properties of poly(4-methyl-1-pentyne (PMP was investigated. Various characterization methods such as FTIR, DSC, SEM and gas adsorption test as well as a series of CO2/CH4 gas separation tests (i.e., pure and mixed gas test were conducted in order to determine the effect of ligand functionalization (–NH2 on the properties of the prepared mixed matrix membranes and their gas transport characteristics. The results of DSC showed that glass transition temperature (Tg increased by increasing NH2-MIL 53 loading. The SEM images also demonstrated that the NH2-MIL 53 particles were dispersed well in the PMP matrix with no noticeable agglomeration. The gas adsorption test of NH2-MIL 53 particles revealed there was a selective adsorption behavior with respect to CO2. It was also found that, incorporation of NH2-MIL 53 into the PMP resulted in an increase in gas permeability (especially towards CO2 and a higher CO2/CH4 selectivity. Adding 30 wt% NH2-MIL 53 into the polymer matrix increased CO2 permeability and CO2/CH4 selectivity of the mixed gas from 83.35 to 210.21 barrer and 7.61 to 19.88, respectively. Rising the temperature from 30 to 60°C led to the permeability increment of both CO2 and CH4 in the mixed gas test, while the CO2/CH4 selectivity decreased. Moreover, the results showed that amino groups required no regeneration and their performance did not decline during 120 h of permeation test. A comparison between the permeation data and those calculated from permeation models revealed that the Bruggeman model could fit the CO2 permeability data better than the Maxwell and Lewis models.

  4. A microporous MOF with a polar pore surface exhibiting excellent selective adsorption of CO2 from CO2-N2 and CO2-CH4 gas mixtures with high CO2 loading.

    Science.gov (United States)

    Pal, Arun; Chand, Santanu; Elahi, Syed Meheboob; Das, Madhab C

    2017-11-14

    A microporous MOF {[Zn(SDB)(L) 0.5 ]·S} n (IITKGP-5) with a polar pore surface has been constructed by the combination of a V-shaped -SO 2 functionalized organic linker (H 2 SDB = 4,4'-sulfonyldibenzoic acid) with an N-rich spacer (L = 2,5-bis(3-pyridyl)-3,4-diaza-2,4-hexadiene), forming a network with sql(2,6L1) topology. IITKGP-5 is characterized by TGA, PXRD and single crystal X-ray diffraction. The framework exhibits lozenge-shaped channels of an approximate size of 4.2 × 5.6 Å 2 along the crystallographic b axis with a potential solvent accessible volume of 26%. The activated IITKGP-5a revealed a CO 2 uptake capacity of 56.4 and 49 cm 3 g -1 at 273 K/1 atm and 295 K/1 atm, respectively. On the contrary, it takes up a much smaller amount of CH 4 (17 cm 3 g -1 at 273 K and 13.6 cm 3 g -1 at 295 K) and N 2 (5.5 cm 3 g -1 at 273 K; 4 cm 3 g -1 at 295 K) under 1 atm pressure exhibiting its potential for a highly selective adsorption of CO 2 from flue gas as well as a landfill gas mixture. Based on the ideal adsorbed solution theory (IAST), a CO 2 /N 2 selectivity of 435.5 and a CO 2 /CH 4 selectivity of 151.6 have been realized at 273 K/100 kPa. The values at 295 K are 147.8 for CO 2 /N 2 and 23.8 for CO 2 /CH 4 gas mixtures under 100 kPa. In addition, this MOF nearly approaches the target values proposed for PSA and TSA processes for practical utility exhibiting its prospect for flue gas separation with a CO 2 loading capacity of 2.04 mmol g -1 .

  5. CO2/CH4 Separation via Polymeric Blend Membrane

    Directory of Open Access Journals (Sweden)

    H. Sanaeepur

    2013-01-01

    Full Text Available CO2/CH4 gas separation is a very important applicatable process in upgrading the natural gas and landfil gas recovery. In this work, to investigate the membrane separation process performance, the gas permeation results andCO2/CH4 separation characteristics of different prepared membranes (via blending different molecular weights of polyethylene glycol (PEG as a modifier with acrylonitrile-butadiene-styrene (ABS as a backbone structure have been studied. Furthermore, SEM analysis was carried out for morphological investigations. The effect of PEG content on gas transport properties on the selected sample was also studied. The effect of pressure on CO2 permeation was examined and showed that at the pressure beyond 4 bar, permeability is not affected by pressure. The results showed that more or less in all cases, incorporation of PEG molecules without any significant increase in CH4 permeability increases the CO2/CH4 selectivity. From the view point of gas separation applications the resultant data are within commercial attractive range

  6. Experimental measurements of vapor-liquid equilibria of the H2O + CO2 + CH4 ternary system

    Science.gov (United States)

    Qin, J.; Rosenbauer, R.J.; Duan, Zhenhao

    2008-01-01

    Reported are the experimental measurements on vapor-liquid equilibria in the H2O + CO2 + CH4 ternary system at temperatures from (324 to 375) K and pressures from (10 to 50) MPa. The results indicate that the CH4 solubility in the ternary mixture is about 10 % to 40 % more than that calculated by interpolation from the Henry's law constants of the binary system, H2O + CH4, and the solubility of CO2 is 6 % to 20 % more than what is calculated by the interpolation from the Henry's law constants of the binary mixture, H 2O + CO2. ?? 2008 American Chemical Society.

  7. Glycine formation in CO2:CH4:NH3 ices induced by 0-70 eV electrons

    Science.gov (United States)

    Esmaili, Sasan; Bass, Andrew D.; Cloutier, Pierre; Sanche, Léon; Huels, Michael A.

    2018-04-01

    Glycine (Gly), the simplest amino-acid building-block of proteins, has been identified on icy dust grains in the interstellar medium, icy comets, and ice covered meteorites. These astrophysical ices contain simple molecules (e.g., CO2, H2O, CH4, HCN, and NH3) and are exposed to complex radiation fields, e.g., UV, γ, or X-rays, stellar/solar wind particles, or cosmic rays. While much current effort is focused on understanding the radiochemistry induced in these ices by high energy radiation, the effects of the abundant secondary low energy electrons (LEEs) it produces have been mostly assumed rather than studied. Here we present the results for the exposure of multilayer CO2:CH4:NH3 ice mixtures to 0-70 eV electrons under simulated astrophysical conditions. Mass selected temperature programmed desorption (TPD) of our electron irradiated films reveals multiple products, most notably intact glycine, which is supported by control measurements of both irradiated or un-irradiated binary mixture films, and un-irradiated CO2:CH4:NH3 ices spiked with Gly. The threshold of Gly formation by LEEs is near 9 eV, while the TPD analysis of Gly film growth allows us to determine the "quantum" yield for 70 eV electrons to be about 0.004 Gly per incident electron. Our results show that simple amino acids can be formed directly from simple molecular ingredients, none of which possess preformed C—C or C—N bonds, by the copious secondary LEEs that are generated by ionizing radiation in astrophysical ices.

  8. CO2/CH4 Separation by a Mixed Matrix Membrane of Polymethylpentyne/MIL-53 Particles

    Directory of Open Access Journals (Sweden)

    Reza Abedini

    2014-10-01

    Full Text Available The effect of Materials Institute Lavoisier-53 (MIL-53 particles on gas transport properties of polymethylpentyne (PMP was investigated. MIL-53 was added to the polymer matrix with different loadings of 10, 20 and 30 wt%. The properties of MIL-53 and prepared membranes were analyzed through FTIR, SEM and TGA methods. The adsorption of CO2 and CH4 was conducted and analyzed accurately through Langmuir equation to investigate the gas transport properties of membranes. The results from TGA showed that degradation temperature (Td increases significantly with increasing MIL-53 loading. SEM images demonstrated that MIL-53 particles dispersed well in polymer matrix with no considerable agglomeration and no non-selective void formation at polymer/filler interface. In addition, CO2 and CH4 permeability measurement along with calculation of CO2/CH4 selectivity were performed. The results showed that the permeability of gases (especially for CO2 increased significantly by increasing the MIL-53 loading. Additionally, CO2/CH4 selectivity showed an increasing trend with increasing the MIL-53 weight percent. Unlike CH4, the CO2 solubility coefficient increased with increasing the MIL-53 loading because of high free volume of membrane and selective adsorption of CO2 with MIL-53. Despite CO2 solubility enhancement its diffusivity coefficient remained more or less unchanged. The enhancement in CH4 permeability has been mainly attributed to its slight incremental diffusivity due to the membrane's increasingly higher free volume. Finally, a comparison between membranes performance and CO2/CH4 Robeson upper bound showed that, the performance of membranes improved due to the presence of MIL-53 which was very close to the Robeson bound.

  9. Flask sample measurements for CO2, CH4 and CO using cavity ring-down spectrometry

    Science.gov (United States)

    Wang, J.-L.; Jacobson, G.; Rella, C. W.; Chang, C.-Y.; Liu, I.; Liu, W.-T.; Chew, C.; Ou-Yang, C.-F.; Liao, W.-C.; Chang, C.-C.

    2013-08-01

    In recent years, cavity ring-down spectrometry (CRDS) has been demonstrated to be a highly sensitive, stable and fast analytical technique for real-time in situ measurements of greenhouse gases. In this study, we propose the technique (which we call flask-CRDS) of analyzing whole air flask samples for CO2, CH4 and CO using a custom gas manifold designed to connect to a CRDS analyzer. Extremely stable measurements of these gases can be achieved over a large pressure range in the flask, from 175 to 760 Torr. The wide pressure range is conducive to flask sample measurement in three ways: (1) flask samples can be collected in low-pressure environments (e.g. high-altitude locations); (2) flask samples can be first analyzed for other trace gases with the remaining low-pressure sample for CRDS analysis of CO2, CH4 and CO; and (3) flask samples can be archived and re-analyzed for validation. The repeatability of this method (1σ of 0.07 ppm for CO2, 0.4 ppb for CH4, and 0.5 ppb for CO) was assessed by analyzing five canisters filled with the same air sample to a pressure of 200 Torr. An inter-comparison of the flask-CRDS data with in-situ CRDS measurements at a high-altitude mountain baseline station revealed excellent agreement, with differences of 0.10 ± 0.09 ppm (1σ) for CO2 and 0.9 ± 1.0 ppb for CH4. This study demonstrated that the flask-CRDS method was not only simple to build and operate but could also perform highly accurate and precise measurements of atmospheric CO2, CH4 and CO in flask samples.

  10. PEBAX®/PAN Hollow Fiber Membranes for CO2/CH4 Separation

    Czech Academy of Sciences Publication Activity Database

    Esposito, E.; Clarizia, G.; Bernardo, P.; Jansen, J. C.; Sedláková, Zuzana; Izák, Pavel; Curcio, S.; de Cindio, B.; Tasselli, F.

    2015-01-01

    Roč. 94, SI (2015), s. 53-61 ISSN 0255-2701. [International Congress of Chemical and Process Engineering CHISA 2014 /21./ and Conference PRES 2014 /17./. Prague, 23.08.2014-27.08.2014] R&D Projects: GA ČR GA14-12695S Grant - others:INRP(IT) MicroPERLA:PON01_01840 Institutional support: RVO:67985858 Keywords : composite membrane * hollow fibers * CO2/CH4 separation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.154, year: 2015

  11. Modified ZIF-8 mixed matrix membrane for CO2/CH4 separation

    Science.gov (United States)

    Nordin, Nik Abdul Hadi Md; Ismail, Ahmad Fauzi; Misdan, Nurasyikin; Nazri, Noor Aina Mohd

    2017-10-01

    Tunability of metal-organic frameworks (MOFs) properties enables them to be tailored for specific applications. In this study, zeolitic imidazole framework 8 (ZIF-8), sub-class of MOF, underwent pre-synthesis and post-synthesis modifications. The pre-synthesis modification using GO (ZIF-8/GO) shows slight decrease in textural properties, while the post-synthesis modification using amine solution (ZIF-8/NH2) resulted in superior BET surface area and pore volume. Mixed matrix membranes (MMMs) derived from polysulfone (PSf) and the modified ZIF-8s were then prepared via dry/wet phase inversion. The polymer chain flexibility of the resulted MMMs shows rigidification, where ZIF-8/NH2 as filler resulting higher rigidification compared to ZIF-8/GO. The MMMs were further subjected to pure CO2 and CH4 gas permeation experiments. The PSf/ZIF-8/NH2 shows superior CO2/CH4 selectivity (88% increased) while sacrificing CO2 permeance due to combination of severe polymer chain rigidification and the presence of CO2-philic group, amine. Whereas, the PSf/ZIF-8/GO possess 64% increase in CO2 permeance without notable changes in CO2/CH4 selectivity.

  12. A new metal-organic framework for separation of C2H2/CH4 and CO2/CH4 at room temperature

    Science.gov (United States)

    Duan, Xing; Zhou, You; Lv, Ran; Yu, Ben; Chen, Haodong; Ji, Zhenguo; Cui, Yuanjing; Yang, Yu; Qian, Guodong

    2018-04-01

    A 3D microporous metal-organic framework with open Cu2+ sites and suitable pore space, [Cu2(L)(H2O)2]·(H2O)4(DMF)8 (ZJU-15, H4L = 5,5‧-(9H-carbazole-2,7-diyl)diisophthalic acid; DMF = N,N-dimethylformamide; ZJU = Zhejiang University), has been constructed and characterized. The activated ZJU-15a has three different types of cages and exhibits BET surface area of 1660 m2 g-1, and can separate gas mixture of C2H2/CH4 and CO2/CH4 at room temperature.

  13. Hindering effects in diffusion of CO2/CH4 mixtures in ZIF-8 crystals

    NARCIS (Netherlands)

    Chmelik, C.; van Baten, J.; Krishna, R.

    2012-01-01

    Cage-type micro-porous materials such as LTA, CHA, SAPO-34, DDR, ERI, ZIF-7, and ZIF-8 have significant potential for use in membrane technologies for CO2 capture. The permeation selectivities are governed by a combination of adsorption and diffusion selectivities, each of which can be separately

  14. Airborne measurements of CO2, CH4 and HCN in boreal biomass burning plumes

    Science.gov (United States)

    O'Shea, Sebastian J.; Bauguitte, Stephane; Muller, Jennifer B. A.; Le Breton, Michael; Archibald, Alex; Gallagher, Martin W.; Allen, Grant; Percival, Carl J.

    2013-04-01

    Biomass burning plays an important role in the budgets of a variety of atmospheric trace gases and particles. For example, fires in boreal Russia have been linked with large growths in the global concentrations of trace gases such as CO2, CH4 and CO (Langenfelds et al., 2002; Simpson et al., 2006). High resolution airborne measurements of CO2, CH4 and HCN were made over Eastern Canada onboard the UK Atmospheric Research Aircraft FAAM BAe-146 from 12 July to 4 August 2011. These observations were made as part of the BORTAS project (Quantifying the impact of BOReal forest fires on Tropospheric oxidants over the Atlantic using Aircraft and Satellites). Flights were aimed at transecting and sampling the outflow from the commonly occurring North American boreal forest fires during the summer months and to investigate and identify the chemical composition and evolution of these plumes. CO2 and CH4 dry air mole fractions were determined using an adapted system based on a Fast Greenhouse Gas Analyser (FGGA, Model RMT-200) from Los Gatos Research Inc, which uses the cavity enhanced absorption spectroscopy technique. In-flight calibrations revealed a mean accuracy of 0.57 ppmv and 2.31 ppbv for 1 Hz observations of CO2 and CH4, respectively, during the BORTAS project. During these flights a number of fresh and photochemically-aged plumes were identified using simultaneous HCN measurements. HCN is a distinctive and useful marker for forest fire emissions and it was detected using chemical ionisation mass spectrometry (CIMS). In the freshest plumes, strong relationships were found between CH4, CO2 and other tracers for biomass burning. From this we were able to estimate that 8.5 ± 0.9 g of CH4 and 1512 ± 185 g of CO2 were released into the atmosphere per kg of dry matter burnt. These emission factors are in good agreement with estimates from previous studies and can be used to calculate budgets for the region. However for aged plumes the correlations between CH4 and other

  15. Effects of hydroxyl-functionalization and sub-Tg thermal annealing on high pressure pure- and mixed-gas CO2/CH4 separation by polyimide membranes based on 6FDA and triptycene-containing dianhydrides

    KAUST Repository

    Swaidan, Raja

    2015-02-01

    A sub-Tg thermally-annealed (250°C, 24h) ultra-microporous PIM-polyimide bearing a 9,10-diisopropyl-triptycene contortion center and hydroxyl-functionalized diamine (2,2-bis(3-amino-4-hydroxyphenyl)-hexafluoropropane, APAF) exhibited plasticization resistance up to 50bar for a 1:1 CO2/CH4 feed mixture, with a 9-fold higher CO2 permeability (30Barrer) and 2-fold increase in CO2/CH4 permselectivity (~50) over conventional dense cellulose acetate membranes at 10bar CO2 partial pressure. Interestingly, mixed-gas CO2/CH4 permselectivities were 10-20% higher than those evaluated under pure-gas conditions due to reduction of mixed-gas CH4 permeability by co-permeation of CO2. Gas transport, physisorption and fluorescence studies indicated a sieving pore-structure engaged in inter-chain charge transfer complexes (CTCs), similar to that of low-free-volume 6FDA-APAF polyimide. The isosteric heat of adsorption of CO2 as well as CO2/CH4 solubility selectivities varied negligibly upon replacement of OH with CH3 but CTC formation was hindered, CO2 sorption increased, CO2 permeability increased ~3-fold, CO2/CH4 permselectivity dropped to ~30 and CH4 mixed-gas co-permeation increased. These results suggest that hydroxyl-functionalization did not cause preferential polymer-gas interactions but primarily elicited diffusion-dominated changes owing to a tightened microstructure more resistant to CO2-induced dilations. Solution-processable hydroxyl-functionalized PIM-type polyimides provide a new platform of advanced materials that unites the high selectivities of low-free-volume polymers with the high permeabilities of PIM-type materials particularly for natural gas sweetening applications.

  16. Hydrogenation of organic matter as a terminal electron sink sustains high CO 2 :CH 4 production ratios during anaerobic decomposition

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Rachel M.; Tfaily, Malak M.; Rich, Virginia I.; Keller, Jason K.; Bridgham, Scott D.; Zalman, Cassandra Medvedeff; Meredith, Laura; Hanson, Paul J.; Hines, Mark; Pfeifer-Meister, Laurel; Saleska, Scott R.; Crill, Patrick; Cooper, William T.; Chanton, Jeff P.; Kostka, Joel E.

    2017-10-01

    Once inorganic electron acceptors are depleted, organic matter in anoxic environments decomposes by hydrolysis, fermentation, and methanogenesis, requiring syntrophic interactions between microorganisms to achieve energetic favorability. In this classic anaerobic food chain, methanogenesis represents the terminal electron accepting (TEA) process, ultimately producing equimolar CO2 and CH4 for each molecule of organic matter degraded. However, CO2:CH4 production in Sphagnum-derived, mineral-poor, cellulosic peat often substantially exceeds this 1:1 ratio, even in the absence of measureable inorganic TEAs. Since the oxidation state of C in both cellulose-derived organic matter and acetate is 0, and CO2 has an oxidation state of +4, if CH4 (oxidation state -4) is not produced in equal ratio, then some other compound(s) must balance CO2 production by receiving 4 electrons. Here we present evidence for ubiquitous hydrogenation of diverse unsaturated compounds that appear to serve as organic TEAs in peat, thereby providing the necessary electron balance to sustain CO2:CH4 >1. While organic electron acceptors have previously been proposed to drive microbial respiration of organic matter through the reversible reduction of quinone moieties, the hydrogenation mechanism that we propose, by contrast, reduces C-C double bonds in organic matter thereby serving as 1) a terminal electron sink, 2) a mechanism for degrading complex unsaturated organic molecules, 3) a potential mechanism to regenerate electron-accepting quinones, and, in some cases, 4) a means to alleviate the toxicity of unsaturated aromatic acids. This mechanism for CO2 generation without concomitant CH4 production has the potential to regulate the global warming potential of peatlands by elevating CO2:CH4 production ratios.

  17. Fabrication Parameters of Asymmetric Mixed Matrix Matrimid-MIL-53/PMHS Membrane for CO2/CH4 Separation

    Directory of Open Access Journals (Sweden)

    Fatereh Dorosti

    2017-03-01

    Full Text Available Asymmetrically mixed matrix Matrimid-MIL-53 membranes with silicone cover layer were fabricated. For better understanding of membrane fabrication process, three main parameters of fabrication, Matrimid concentration, silicone concentration and weight percentage of metal organic framework (MIL-53 particles, were optimized by an experimental design method. Cross-section SEM images were used to study the membrane structure and polymer-particles interface. Moreover, thermal resistance of the membranes and the existence of various bonds in them were investigated by FTIR and TGA analyses. The results showed that membranes had porous structure with finger-like morphology. At low and moderate percentages of particles, there were no non-selective voids observed at polymer-particles interface. The thermal resistance of membranes increased with the increase of MIL-53 weight percentage and the destruction temperature of polymer increased from 410°C to 450°C. The permeability tests results showed that the Matrimid (20% wt-MIL-53(15% wt/PMHS (10%wt membrane exhibited the highest level of CO2/CH4 selectivity (23.6. However, in the membrane with 30 wt% particles loading, selectivity decreased due to particles agglomeration and void formation. The experimental design results showed that the concentration of silicone in covering solution had significant effect. CO2 and CH4 permeability decreased and ideal selectivity of CO2/CH4 increased with silicone concentration enhancement. Although the Matrimid concentration had a little effect on CO2/CH4 ideal selectivity, its enhancement increased the selectivity of the gases. The optimization results showed the membrane with 17.8% of Matrimd polymer, 13.2% of silicone polymer and 15.5 wt% of MIL-53 particle displayed the highest selectivity and CO2 permeability.

  18. Performance of a geostationary mission, geoCARB, to measure CO2, CH4 and CO column-averaged concentrations

    Directory of Open Access Journals (Sweden)

    I. N. Polonsky

    2014-04-01

    Full Text Available GeoCARB is a proposed instrument to measure column averaged concentrations of CO2, CH4 and CO from geostationary orbit using reflected sunlight in near-infrared absorption bands of the gases. The scanning options, spectral channels and noise characteristics of geoCARB and two descope options are described. The accuracy of concentrations from geoCARB data is investigated using end-to-end retrievals; spectra at the top of the atmosphere in the geoCARB bands are simulated with realistic trace gas profiles, meteorology, aerosol, cloud and surface properties, and then the concentrations of CO2, CH4 and CO are estimated from the spectra after addition of noise characteristic of geoCARB. The sensitivity of the algorithm to aerosol, the prior distributions assumed for the gases and the meteorology are investigated. The contiguous spatial sampling and fine temporal resolution of geoCARB open the possibility of monitoring localised sources such as power plants. Simulations of emissions from a power plant with a Gaussian plume are conducted to assess the accuracy with which the emission strength may be recovered from geoCARB spectra. Scenarios for "clean" and "dirty" power plants are examined. It is found that a reliable estimate of the emission rate is possible, especially for power plants that have particulate filters, by averaging emission rates estimated from multiple snapshots of the CO2 field surrounding the plant. The result holds even in the presence of partial cloud cover.

  19. Plasticization-resistant hollow fiber membranes for CO2/CH4 separation based on a thermally crosslinkable polyimide

    KAUST Repository

    Chen, Chien-Chiang

    2011-10-01

    Decarboxylation-induced thermal crosslinking has been demonstrated to be effective for stabilizing membranes against plasticization in dense films. This study extends this promising crosslinking approach from dense films to industrially relevant asymmetric hollow fiber membranes. Crosslinkable asymmetric hollow fiber membranes were spun from a carboxylic acid containing polyimide, 6FDA-DAM:DABA. Dope and spinning conditions were optimized to obtain fibers with a defect-free selective skin layer. It is found that slightly defective fibers suffered severe selectivity loss after thermal crosslinking, suggesting that defect-free property is essential to the performance of the resulting crosslinked hollow fiber membranes. The crosslinked fibers were tested for CO 2/CH 4 separation. The excellent plasticization resistance under high pressure feeds (with highest CO 2 partial pressure of 400psia) suggests that these robust membranes are promising for aggressive natural gas purification. © 2011 Elsevier B.V.

  20. Development and characterization of polyethersulfone/TiO2 mixed matrix membranes for CO2/CH4 separation

    Science.gov (United States)

    Galaleldin, S.; Mannan, H. A.; Mukhtar, H.

    2017-12-01

    In this study, mixed matrix membranes comprised of polyethersulfone as the bulk polymer phase and titanium dioxide (TiO2) nanoparticles as the inorganic discontinuous phase were prepared for CO2/CH4 separation. Membranes were synthesized at filler loading of 0, 5, 10 and 15 wt % via dry phase inversion method. Morphology, chemical bonding and thermal characteristics of membranes were scrutinized utilizing different techniques, namely: Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform InfraRed (FTIR) spectra and Thermogravimetric analysis (TGA) respectively. Membranes gas separation performance was evaluated for CO2 and CH4 gases at 4 bar feed pressure. The highest separation performance was achieved by mixed matrix membrane (MMM) at 5 % loading of TiO2.

  1. Automated CO2, CH4 and N2O Fluxes from Tree Stems and Soils: Magnitudes, Temporal Patterns and Drivers

    Science.gov (United States)

    Barba, J.; Poyatos, R.; Vargas, R.

    2017-12-01

    The emissions of the main greenhouse gases (GHG; CO2, CH4 and N2O) through tree stems are still an uncertain component of the total GHG balance of forests. Despite that stem CO2 emissions have been studied for several decades, it is still unclear the drivers and spatiotemporal patterns of CH4 and N2O stem emissions. Additionally, it is unknown how stem emissions could be related to soil physiological processes or environmental conditions. We measured CO2, CH4 and N2O emissions hourly from April to July 2017 at two different heights (75 [LStem] and 150cm [HStem]) of bitternut hickory (Carya cordiformis) trees and adjacent soil locations in a forested area in the Mid Atlantic of the USA. We designed an automated system to continuously measure the three greenhouse gases (GHG) in stems and soils. Stem and soil CO2 emissions showed similar seasonal patterns with an average of 6.56±0.09 (soil), 3.72±0.05 (LStem) and 2.47±0.04 µmols m-2 s-1 (HStem) (mean±95% CI). Soil temperature controlled CO2 fluxes at both daily and seasonal scales (R2>0.5 for all cases), but there was no clear effect of soil moisture. The stems were a clear CH4 source with emissions decreasing with height (0.35±0.02 and 0.25±0.01 nmols m-2 s-1 for LStem and HStem, respectively) with no apparent seasonal pattern, and no clear relationship with environmental drivers (e.g., temperature, moisture). In contrast, soil was a CH4 sink throughout the experiment (-0.55±0.02 nmols m-2 s-1) and its seasonal pattern responded to moisture changes. Despite soil and stem N2O emissions did not show a seasonal pattern or apparent dependency on temperature or moisture, they showed net N2O emissions with a decrease in emissions with stem height (0.29±0.05 for soil, 0.38±0.06 for LStem and 0.28±0.05 nmols m-2 s-1 for HStem). The three GHG emissions decreased with stem height at similar rates (33%, 28% and 27% for CO2, CH4 and N2O, respectively). These results suggest that the gases were not produced in the stem

  2. Plasticization-resistant hollow fiber membranes for CO2/CH4 separation based on a thermally crosslinkable polyimide

    KAUST Repository

    Chen, Chien-Chiang; Qiu, Wulin; Miller, Stephen J.; Koros, William J.

    2011-01-01

    Decarboxylation-induced thermal crosslinking has been demonstrated to be effective for stabilizing membranes against plasticization in dense films. This study extends this promising crosslinking approach from dense films to industrially relevant asymmetric hollow fiber membranes. Crosslinkable asymmetric hollow fiber membranes were spun from a carboxylic acid containing polyimide, 6FDA-DAM:DABA. Dope and spinning conditions were optimized to obtain fibers with a defect-free selective skin layer. It is found that slightly defective fibers suffered severe selectivity loss after thermal crosslinking, suggesting that defect-free property is essential to the performance of the resulting crosslinked hollow fiber membranes. The crosslinked fibers were tested for CO 2/CH 4 separation. The excellent plasticization resistance under high pressure feeds (with highest CO 2 partial pressure of 400psia) suggests that these robust membranes are promising for aggressive natural gas purification. © 2011 Elsevier B.V.

  3. CO2, CH4 and N2O fluxes from soil of a burned grassland in Central Africa

    Directory of Open Access Journals (Sweden)

    R. Valentini

    2010-11-01

    Full Text Available The impact of fire on soil fluxes of CO2, CH4 and N2O was investigated in a tropical grassland in Congo Brazzaville during two field campaigns in 2007–2008. The first campaign was conducted in the middle of the dry season and the second at the end of the growing season, respectively one and eight months after burning. Gas fluxes and several soil parameters were measured in each campaign from burned plots and from a close-by control area preserved from fire. Rain events were simulated at each campaign to evaluate the magnitude and duration of the generated gas flux pulses. In laboratory experiments, soil samples from field plots were analysed for microbial biomass, net N mineralization, net nitrification, N2O, NO and CO2 emissions under different water and temperature soil regimes. One month after burning, field CO2 emissions were significantly lower in burned plots than in the control plots, the average daily CH4 flux shifted from net emission in the unburned area to net consumption in burned plots, no significant effect of fire was observed on soil N2O fluxes. Eight months after burning, the average daily fluxes of CO2, CH4 and N2O measured in control and burned plots were not significantly different. In laboratory, N2O fluxes from soil of burned plots were significantly higher than fluxes from soil of unburned plots only above 70% of maximum soil water holding capacity; this was never attained in the field even after rain simulation. Higher NO emissions were measured in the lab in soil from burned plots at both 10% and 50% of maximum soil water holding capacity. Increasing the incubation temperature from 25 °C to 37 °C negatively affected microbial growth, mineralization and nitrification activities but enhanced N2O and CO2 production. Results indicate that fire did not increase post-burning soil GHG emissions in this tropical grasslands characterized by acidic, well drained and nutrient-poor soil.

  4. Fabrication of 6FDA-durene membrane incorporated with zeolite T and aminosilane grafted zeolite T for CO2/CH4 separation

    Science.gov (United States)

    Jusoh, Norwahyu; Fong Yeong, Yin; Keong Lau, Kok; Shariff, Azmi Mohd

    2017-08-01

    In the present work, zeolite T and aminosilane grafted zeolite T are embedded into 6FDA-durene polyimide phase for the fabrication of mixed matrix membranes (MMMs). FESEM images demonstrated that the improvement of interfacial adhesion between zeolite and polymer phases in MMM loaded with aminosilane grafted zeolite T was not significant as compared to zeolite T/6FDA-durene MMM. From the gas permeation test, CO2/CH4 selectivity up to 26.4 was achieved using MMM containing aminosilane grafted zeolite T, while MMM loaded with ungrafted zeolite T showed CO2/CH4 selectivity of 19.1. In addition, MMM incorporated with aminosilane grafted zeolite T particles successfully lies on Robeson upper bound 2008, which makes it an attractive candidate for CO2/CH4 separation.

  5. Transport Mechanisms for CO2-CH4 Exchange and Safe CO2 Storage in Hydrate-Bearing Sandstone

    Directory of Open Access Journals (Sweden)

    Knut Arne Birkedal

    2015-05-01

    Full Text Available CO2 injection in hydrate-bearing sediments induces methane (CH4 production while benefitting from CO2 storage, as demonstrated in both core and field scale studies. CH4 hydrates have been formed repeatedly in partially water saturated Bentheim sandstones. Magnetic Resonance Imaging (MRI and CH4 consumption from pump logs have been used to verify final CH4 hydrate saturation. Gas Chromatography (GC in combination with a Mass Flow Meter was used to quantify CH4 recovery during CO2 injection. The overall aim has been to study the impact of CO2 in fractured and non-fractured samples to determine the performance of CO2-induced CH4 hydrate production. Previous efforts focused on diffusion-driven exchange from a fracture volume. This approach was limited by gas dilution, where free and produced CH4 reduced the CO2 concentration and subsequent driving force for both diffusion and exchange. This limitation was targeted by performing experiments where CO2 was injected continuously into the spacer volume to maintain a high driving force. To evaluate the effect of diffusion length multi-fractured core samples were used, which demonstrated that length was not the dominating effect on core scale. An additional set of experiments is presented on non-fractured samples, where diffusion-limited transportation was assisted by continuous CO2 injection and CH4 displacement. Loss of permeability was addressed through binary gas (N2/CO2 injection, which regained injectivity and sustained CO2-CH4 exchange.

  6. Role of intrachain rigidity in the plasticization of intrinsically microporous triptycene-based polyimide membranes in mixed-Gas CO2/CH4 separations

    KAUST Repository

    Swaidan, Raja; Ghanem, Bader; Al-Saeedi, Majed; Litwiller, Eric; Pinnau, Ingo

    2014-01-01

    is not a singular solution to intrinsic plasticization resistance. Despite the significant intrachain rigidity in TPDA-TMPD, a 300% increase in PMIX(CH4), 50% decrease in α(CO2/CH4) from 24 to 12, and continuous increase in PMIX(CO2) occurred from 4 to 30

  7. Investigating cluster formation in adsorption of CO2, CH4, and Ar in zeolites and metal organic frameworks at subcritical temperatures

    NARCIS (Netherlands)

    Krishna, R.; van Baten, J.M.

    2010-01-01

    The critical temperatures, T-c, of CO2, CH4, and Ar are 304 K, 191 K, and 151 K, respectively. This paper highlights some unusual characteristics of adsorption and diffusion of these molecules in microporous structures such as zeolites and metal organic frameworks at temperatures T < T-c. Published

  8. A single gas chromatograph for accurate atmospheric mixing ratio measurements of CO2, CH4, N2O, SF6 and CO

    NARCIS (Netherlands)

    van der Laan, S.; Neubert, R. E. M.; Meijer, H. A. J.; Simpson, W.R.

    2009-01-01

    We present an adapted gas chromatograph capable of measuring simultaneously and semi-continuously the atmospheric mixing ratios of the greenhouse gases CO2, CH4, N2O and SF6 and the trace gas CO with high precision and long-term stability. The novelty of our design is that all species are measured

  9. Pure- and mixed-gas CO2/CH4 separation properties of PIM-1 and an amidoxime-functionalized PIM-1

    KAUST Repository

    Swaidan, Raja; Ghanem, Bader; Litwiller, Eric; Pinnau, Ingo

    2014-01-01

    to the design and evaluation of PIMs for economical natural gas sweetening is a high and stable CO2/CH4 selectivity under realistic, mixed-gas conditions. Here, amidoxime-functionalized PIM-1 (AO-PIM-1) was prepared and examined for fundamental structure

  10. Pure- and mixed-gas CO2/CH4 separation properties of PIM-1 and an amidoxime-functionalized PIM-1

    KAUST Repository

    Swaidan, Raja

    2014-05-01

    The prototypical solution-processable polymer of intrinsic microporosity, PIM-1, and derivatives thereof offer combinations of permeability and selectivity that make them potential candidate materials for membrane-based gas separations. Paramount to the design and evaluation of PIMs for economical natural gas sweetening is a high and stable CO2/CH4 selectivity under realistic, mixed-gas conditions. Here, amidoxime-functionalized PIM-1 (AO-PIM-1) was prepared and examined for fundamental structure/property relationships. Qualitative NLDFT pore-size distribution analyses of physisorption isotherms (N2 at -196 oC; CO2 at 0 oC) reveal a tightened microstructure indicating size-sieving ultra-microporosity (<7Å). AO-PIM-1 demonstrated a three-fold increase in αD(CO2/CH4) over PIM-1, surpassing the 2008 upper bound with P(CO2)=1153Barrer and ideal α(CO2/CH4)=34. Under a 50:50 CO2:CH4 mixed-gas feed, AO-PIM-1 showed less selectivity loss than PIM-1, maintaining a mixed-gas α(CO2/CH4) ~21 across a 20bar pressure range. Conversely, PIM-1 endured up to 60% increases in mixed-gas CH4 permeability over pure-gas values concurrent with a selectivity of only ~8 at 20bar. A pervasive intermolecular hydrogen bonding network in AO-PIM-1 predominantly yields a rigidified microstructure that mitigates CO2-induced matrix dilations, reducing detrimental mixed-gas CH4 copermeation. © 2014 Elsevier B.V.

  11. Pure- and Mixed-Gas Permeation Properties of Highly Selective and Plasticization Resistant Hydroxyl-Diamine-Based 6FDA Polyimides for CO2/CH4 Separation

    KAUST Repository

    Alaslai, Nasser Y.; Ghanem, Bader; Alghunaimi, Fahd; Litwiller, Eric; Pinnau, Ingo

    2016-01-01

    The effect of hydroxyl functionalization on the m-phenylene diamine moiety of 6FDA dianhydride-based polyimides was investigated for gas separation applications. Pure-gas permeability coefficients of He, H2, N2, O2, CH4, and CO2 were measured at 35 °C and 2 atm. The introduction of hydroxyl groups in the diamine moiety of 6FDA-diaminophenol (DAP) and 6FDA-diamino resorcinol (DAR) polyimides tightened the overall polymer structure due to increased charge transfer complex formation compared to unfunctionalized 6FDA-m-phenylene diamine (mPDA). The BET surface areas based on nitrogen adsorption of 6FDA-DAP (54 m2g−1) and of 6FDA-DAR (45 m2g−1) were ~18% and 32% lower than that of 6FDA-mPDA (66 m2g−1). 6FDA-mPDA had a pure-gas CO2 permeability of 14 Barrer and CO2/CH4 selectivity of 70. The hydroxyl-functionalized polyimides 6FDA-DAP and 6FDA-DAR exhibited very high pure-gas CO2/CH4 selectivities of 92 and 94 with moderate CO2 permeability of 11 and 8 Barrer, respectively. It was demonstrated that hydroxyl-containing polyimide membranes maintained very high CO2/CH4 selectivity (~ 75 at CO2 partial pressure of 10 atm) due to CO2 plasticization resistance when tested under high-pressure mixed-gas conditions. Functionalization with hydroxyl groups may thus be a promising strategy towards attaining highly selective polyimides for economical membrane-based natural gas sweetening.

  12. Pure- and Mixed-Gas Permeation Properties of Highly Selective and Plasticization Resistant Hydroxyl-Diamine-Based 6FDA Polyimides for CO2/CH4 Separation

    KAUST Repository

    Alaslai, Nasser Y.

    2016-01-05

    The effect of hydroxyl functionalization on the m-phenylene diamine moiety of 6FDA dianhydride-based polyimides was investigated for gas separation applications. Pure-gas permeability coefficients of He, H2, N2, O2, CH4, and CO2 were measured at 35 °C and 2 atm. The introduction of hydroxyl groups in the diamine moiety of 6FDA-diaminophenol (DAP) and 6FDA-diamino resorcinol (DAR) polyimides tightened the overall polymer structure due to increased charge transfer complex formation compared to unfunctionalized 6FDA-m-phenylene diamine (mPDA). The BET surface areas based on nitrogen adsorption of 6FDA-DAP (54 m2g−1) and of 6FDA-DAR (45 m2g−1) were ~18% and 32% lower than that of 6FDA-mPDA (66 m2g−1). 6FDA-mPDA had a pure-gas CO2 permeability of 14 Barrer and CO2/CH4 selectivity of 70. The hydroxyl-functionalized polyimides 6FDA-DAP and 6FDA-DAR exhibited very high pure-gas CO2/CH4 selectivities of 92 and 94 with moderate CO2 permeability of 11 and 8 Barrer, respectively. It was demonstrated that hydroxyl-containing polyimide membranes maintained very high CO2/CH4 selectivity (~ 75 at CO2 partial pressure of 10 atm) due to CO2 plasticization resistance when tested under high-pressure mixed-gas conditions. Functionalization with hydroxyl groups may thus be a promising strategy towards attaining highly selective polyimides for economical membrane-based natural gas sweetening.

  13. Comparison of Landfill Methane Oxidation Measured Using Stable Isotope Analysis and CO2/CH4 Fluxes Measured by the Eddy Covariance Method

    Science.gov (United States)

    Xu, L.; Chanton, J.; McDermitt, D. K.; Li, J.; Green, R. B.

    2015-12-01

    Methane plays a critical role in the radiation balance and chemistry of the atmosphere. Globally, landfill methane emission contributes about 10-19% of the anthropogenic methane burden into the atmosphere. In the United States, 18% of annual anthropogenic methane emissions come from landfills, which represent the third largest source of anthropogenic methane emissions, behind enteric fermentation and natural gas and oil production. One uncertainty in estimating landfill methane emissions is the fraction of methane oxidized when methane produced under anaerobic conditions passes through the cover soil. We developed a simple stoichiometric model to estimate methane oxidation fraction when the anaerobic CO2 / CH4 production ratio is known, or can be estimated. The model predicts a linear relationship between CO2 emission rates and CH4 emission rates, where the slope depends on anaerobic CO2 / CH4 production ratio and the fraction of methane oxidized, and the intercept depends on non-methane-dependent oxidation processes. The model was tested using carbon dioxide emission rates (fluxes) and methane emission rates (fluxes) measured using the eddy covariance method over a one year period at the Turkey Run landfill in Georgia, USA. The CO2 / CH4 production ratio was estimated by measuring CO2 and CH4 concentrations in air sampled under anaerobic conditions deep inside the landfill. We also used a mass balance approach to independently estimate fractional oxidation based on stable isotope measurements (δ13C of methane) of gas samples taken from deep inside the landfill and just above the landfill surface. Results from the two independent methods agree well. The model will be described and methane oxidation will be discussed in relation to wind direction, location at the landfill, and age of the deposited refuse.

  14. Role of intrachain rigidity in the plasticization of intrinsically microporous triptycene-based polyimide membranes in mixed-Gas CO2/CH4 separations

    KAUST Repository

    Swaidan, Raja

    2014-11-11

    Based on high-pressure pure- and mixed-gas (50:50) CO2/CH4 separation properties of two intrinsically microporous triptycene-based polyimides (TPDA-TMPD and TPDA-6FpDA), the intrachain rigidity central to "conventional PIM" design principles is not a singular solution to intrinsic plasticization resistance. Despite the significant intrachain rigidity in TPDA-TMPD, a 300% increase in PMIX(CH4), 50% decrease in α(CO2/CH4) from 24 to 12, and continuous increase in PMIX(CO2) occurred from 4 to 30 bar. On the other hand, the more flexible and densely packed TPDA-6FpDA exhibited a slight upturn in PMIX(CO2) at 20 bar similar to a dense cellulose acetate (CA) film, also reported here, despite a 4-fold higher CO2 sorption capacity. Microstructural investigations suggest that the interconnected O2- and H2-sieving ultramicroporosity of TPDA-TMPD is more sensitive to slight CO2-induced dilations and is the physical basis for a more extensive and accelerated plasticization. Interchain rigidity, potentially by interchain interactions, is emphasized and may be facilitated by intrachain mobility.

  15. Influence of pyrolysis conditions on the CO2/CH4 and O2/N2 perm selectivity of supported carbon molecular sieve membranes

    International Nuclear Information System (INIS)

    Mohd Fikri Abdul Rahman; Wan Mohd Hafiz Faizal Wan Harun; Mohd Azmier Ahmad

    2010-01-01

    This work focused on the effect of pyrolysis conditions onto supported carbon molecular sieve membranes performance in pure gas permeation and perm selectivity. The membrane support was synthesis by carbonization of titania mixed with cellulose acetate at temperature of 125 degree Celsius. The molecular sieving membrane layer was obtained by coating the polyvinyl alcohol-glutaraldehyde solution onto the membrane support before heated at various pyrolysis temperatures and holding times. The optimum preparation conditions were found at pyrolysis temperature and holding time of 400 degree Celsius and 30 minutes, respectively. At this point, the CO 2 and O 2 permeation flux were 2.63 ml/ min and 2.67 ml/ min, respectively. Meanwhile, the perm selectivities of CO 2 / CH 4 and O 2 / N 2 were 1.87 and 1.92, respectively. (author)

  16. A mobile automatic gas chromatograph system to measure CO2, CH4 and N2O fluxes from soil in the field

    International Nuclear Information System (INIS)

    Silvola, J.; Martikainen, P.; Nykaenen, H.

    1992-01-01

    A caravan has been converted into mobile laboratory for measuring fluxes of CO 2 , CH 4 and N 2 O from the soil in the field. The caravan was equipped with a gas chromatograph fitted with TC-, FI- and EC-detectors, and a PC controlled data logger. The gas collecting chambers can be used up to 50 m from the caravan. The closing and opening of the chambers, as well as the flows of sample gases from chambers to the gas chromatograph. is pneumatically regulated. Simultaneous recordings of temperature, light intensity and the depth of water table are made. The system has been used for two months in 1992, and some preliminary results are presented

  17. Small scale soil carbon and moisture gradients in a drained peat bog grassland and their influence on CO2, CH4 and N2O fluxes

    Science.gov (United States)

    Leiber-Sauheitl, K.; Fuß, R.; Freibauer, A.

    2012-04-01

    Due to the UNFCCC report requirements of each country on the emissions of greenhouse gases from key sources the joint research project "Organic Soils" was established in Germany. The project's objective is to improve the data set on greenhousegas emissions from organic soils in Germany. Within 12 German Project Catchments emissions from different types of organic soils, e.g. under different land uses and hydrological conditions, are measured. At the location "Großes Moor" near Gifhorn (Lower Saxony) the effects of small-scale soil organic carbon and groundwater level gradients on the GHG fluxes (CO2, CH4 and N2O) are quantified. The study area is located within a former peat bog altered by drainage and peat cutting, which is currently grassland under extensive agricultural use. The focus of the study is on the acquisition of CO2, CH4 and N2O fluxes on six sites via manual closed chambers. In order to calculate the annual CO2 exchange rate, values are interpolated on a 0.5 hour scale between measurement campaigns. In combination with continually logged meteorological parameters, such as the photosynthetic active radiation as well as air and soil temperatures, we calculate the daily CO2 ecosystem exchange of the different sites. During the 2011 campaign, CO2 was determined as the most important greenhouse gas. The groundwater table was the dominant variable influencing gas emissions. Another important factor was the vegetation composition. In detail, highest CO2 emissions occurred with a water table of 40-50 cm below ground level, temperatures above 10°C and low plant biomass amounts. Due to the more complex formation of N2O by a number of processes, each being promoted by different soil conditions, the measurement of N2O fluxes in the field was complemented by a laboratory experiment. In this, the use of stable isotope tracer techniques enabled us to quantify the contribution of single biochemical pathways to the overall formation of N2O under controlled

  18. Fluid geochemistry and soil gas fluxes (CO2-CH4-H2S) at a promissory Hot Dry Rock Geothermal System: The Acoculco caldera, Mexico

    Science.gov (United States)

    Peiffer, L.; Bernard-Romero, R.; Mazot, A.; Taran, Y. A.; Guevara, M.; Santoyo, E.

    2014-09-01

    The Acoculco caldera has been recognized by the Mexican Federal Electricity Company (CFE) as a Hot Dry Rock Geothermal System (HDR) and could be a potential candidate for developing an Enhanced Geothermal System (EGS). Apart from hydrothermally altered rocks, geothermal manifestations within the Acoculco caldera are scarce. Close to ambient temperature bubbling springs and soil degassing are reported inside the caldera while a few springs discharge warm water on the periphery of the caldera. In this study, we infer the origin of fluids and we characterize for the first time the soil degassing dynamic. Chemical and isotopic (δ18O-δD) analyses of spring waters indicate a meteoric origin and the dissolution of CO2 and H2S gases, while gas chemical and isotopic compositions (N2/He, 3He/4He, 13C, 15N) reveal a magmatic contribution with both MORB- and arc-type signatures which could be explained by an extension regime created by local and regional fault systems. Gas geothermometry results are in agreement with temperature measured during well drilling (260 °C-300 °C). Absence of well-developed water reservoir at depth impedes re-equilibration of gases upon surface. A multi-gas flux survey including CO2, CH4 and H2S measurements was performed within the caldera. Using the graphical statistical analysis (GSA) approach, CO2 flux measurements were classified in two populations. Population A, representing 95% of measured fluxes is characterized by low values (mean: 18 g m- 2 day- 1) while the remaining 5% fluxes belonging to Population B are much higher (mean: 5543 g m- 2 day- 1). This low degassing rate probably reflects the low permeability of the system, a consequence of the intense hydrothermal alteration observed in the upper 800 m of volcanic rocks. An attempt to interpret the origin and transport mechanism of these fluxes is proposed by means of flux ratios as well as by numerical modeling. Measurements with CO2/CH4 and CO2/H2S flux ratios similar to mass ratios

  19. Amino-Functionalized ZIF-7 Nanocrystals: Improved Intrinsic Separation Ability and Interfacial Compatibility in Mixed-Matrix Membranes for CO2 /CH4 Separation.

    Science.gov (United States)

    Xiang, Long; Sheng, Luqian; Wang, Chongqing; Zhang, Lixiong; Pan, Yichang; Li, Yanshuo

    2017-08-01

    Highly permeable and selective, as well as plasticization-resistant membranes are desired as promising alternatives for cost- and energy-effective CO 2 separation. Here, robust mixed-matrix membranes based on an amino-functionalized zeolitic imidazolate framework ZIF-7 (ZIF-7-NH 2 ) and crosslinked poly(ethylene oxide) rubbery polymer are successfully fabricated with filler loadings up to 36 wt%. The ZIF-7-NH 2 materials synthesized from in situ substitution of 2-aminobenzimidazole into the ZIF-7 structure exhibit enlarged aperture size compared with monoligand ZIF-7. The intrinsic separation ability for CO 2 /CH 4 on ZIF-7-NH 2 is remarkably enhanced as a result of improved CO 2 uptake capacity and diffusion selectivity. The incorporation of ZIF-7-NH 2 fillers simultaneously makes the neat polymer more permeable and more selective, surpassing the state-of-the-art 2008 Robeson upper bound. The chelating effect between metal (zinc) nodes of fillers and ester groups of a polymer provides good bonding, enhancing the mechanical strength and plasticization resistance of the neat polymer membrane. The developed novel ZIF-7 structure with amino-function and the resulting nanocomposite membranes are very attractive for applications like natural-gas sweetening or biogas purification. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Emission factors and their uncertainty for the exchange of CO2, CH4 and N2O in Finnish managed peatlands

    International Nuclear Information System (INIS)

    Alm, J.; Shurpali, N. J.; Minkkinen, K.

    2007-01-01

    This paper summarises the results of several research groups participating in the research programme 'Greenhouse Impacts of the use of Peat and Peatlands in Finland', and presents emission factors for peat-atmosphere fluxes of CO 2 , CH 4 , and N 2 O, filling gaps in knowledge concerning the afforestation of organic croplands and cutaways, and improves the emission assessment of peatlands drained for forestry. Forest drainage may result in net binding of soil carbon or net release, depending on site characteristics and the tree stand. Use of peatlands for agriculture (48-4821 g CO 2 -eq. m -2 a -1 ), even after the cultivation has ceased, or for milled peat harvesting (1948-2478 g CO 2 -eq. m -2 a -1 ) can cause the highest overall emissions. Extremely high CO 2 emissions are possible from peat harvesting areas during wet and warm summers. Afforestation of those peatlands abandoned from cultivation or peat harvesting can reduce the warming impact at least during the first tree generation. Heterotrophic soil respiration may have a systematic south-north difference in temperature response. More data must be collected before the information on peatland forest soil CO 2 emissions can be adapted for different climatic regions in Finland. A test of the model DNDC against measured data showed that DNDC has to be developed further before it can be used in estimating N 2 O emissions from boreal peatlands. (orig.)

  1. A 156 kyr smoothed history of the atmospheric greenhouse gases CO2, CH4, and N2O and their radiative forcing

    Science.gov (United States)

    Köhler, Peter; Nehrbass-Ahles, Christoph; Schmitt, Jochen; Stocker, Thomas F.; Fischer, Hubertus

    2017-06-01

    Continuous records of the atmospheric greenhouse gases (GHGs) CO2, CH4, and N2O are necessary input data for transient climate simulations, and their associated radiative forcing represents important components in analyses of climate sensitivity and feedbacks. Since the available data from ice cores are discontinuous and partly ambiguous, a well-documented decision process during data compilation followed by some interpolating post-processing is necessary to obtain those desired time series. Here, we document our best possible data compilation of published ice core records and recent measurements on firn air and atmospheric samples spanning the interval from the penultimate glacial maximum ( ˜ 156 kyr BP) to the beginning of the year 2016 CE. We use the most recent age scales for the ice core data and apply a smoothing spline method to translate the discrete and irregularly spaced data points into continuous time series. These splines are then used to compute the radiative forcing for each GHG using well-established, simple formulations. We compile only a Southern Hemisphere record of CH4 and discuss how much larger a Northern Hemisphere or global CH4 record might have been due to its interpolar difference. The uncertainties of the individual data points are considered in the spline procedure. Based on the given data resolution, time-dependent cutoff periods of the spline, defining the degree of smoothing, are prescribed, ranging from 5000 years for the less resolved older parts of the records to 4 years for the densely sampled recent years. The computed splines seamlessly describe the GHG evolution on orbital and millennial timescales for glacial and glacial-interglacial variations and on centennial and decadal timescales for anthropogenic times. Data connected with this paper, including raw data and final splines, are available at PANGAEA.871273" target="_blank">doi:10.1594/PANGAEA.871273.

  2. A single gas chromatograph for accurate atmospheric mixing ratio measurements of CO2, CH4, N2O, SF6 and CO

    Directory of Open Access Journals (Sweden)

    H. A. J. Meijer

    2009-09-01

    Full Text Available We present an adapted gas chromatograph capable of measuring simultaneously and semi-continuously the atmospheric mixing ratios of the greenhouse gases CO2, CH4, N2O and SF6 and the trace gas CO with high precision and long-term stability. The novelty of our design is that all species are measured with only one device, making it a very cost-efficient system. No time lags are introduced between the measured mixing ratios. The system is designed to operate fully autonomously which makes it ideal for measurements at remote and unmanned stations. Only a small amount of sample air is needed, which makes this system also highly suitable for flask air measurements. In principle, only two reference cylinders are needed for daily operation and only one calibration per year against international WMO standards is sufficient to obtain high measurement precision and accuracy. The system described in this paper is in use since May 2006 at our atmospheric measurement site Lutjewad near Groningen, The Netherlands at 6°21´ E, 53°24´N, 1 m a.s.l. Results show the long-term stability of the system. Observed measurement precisions at our remote research station Lutjewad were: ±0.04 ppm for CO2, ±0.8 ppb for CH4, ±0.8 ppb for CO, ±0.3 ppb for N2O, and ±0.1 ppt for SF6. The ambient mixing ratios of all measured species as observed at station Lutjewad for the period of May 2007 to August 2008 are presented as well.

  3. Transport and transformation of soil-derived CO2, CH4 and DOC sustain CO2 supersaturation in small boreal streams.

    Science.gov (United States)

    Rasilo, Terhi; Hutchins, Ryan H S; Ruiz-González, Clara; Del Giorgio, Paul A

    2017-02-01

    Streams are typically supersaturated in carbon dioxide (CO 2 ) and methane (CH 4 ), and are recognized as important components of regional carbon (C) emissions in northern landscapes. Whereas there is consensus that in most of the systems the CO 2 emitted by streams represents C fixed in the terrestrial ecosystem, the pathways delivering this C to streams are still not well understood. We assessed the contribution of direct soil CO 2 injection versus the oxidation of soil-derived dissolved organic C (DOC) and CH 4 in supporting CO 2 supersaturation in boreal streams in Québec. We measured the concentrations of CO 2 , CH 4 and DOC in 43 streams and adjacent soil waters during summer base-flow period. A mass balance approach revealed that all three pathways are significant, and that the mineralization of soil-derived DOC and CH 4 accounted for most of the estimated stream CO 2 emissions (average 75% and 10%, respectively), and that these estimated contributions did not change significantly between the studied low order (≤3) streams. Whereas some of these transformations take place in the channel proper, our results suggest that they mainly occur in the hyporheic zones of the streams. Our results further show that stream CH 4 emissions can be fully explained by soil CH 4 inputs. This study confirms that these boreal streams, and in particular their hyporheic zones, are extremely active processors of soil derived DOC and CH 4 , not just vents for soil produced CO 2 . Copyright © 2016 Elsevier B.V. All rights reserved.

  4. A 156 kyr smoothed history of the atmospheric greenhouse gases CO2, CH4, and N2O and their radiative forcing

    Directory of Open Access Journals (Sweden)

    P. Köhler

    2017-06-01

    Full Text Available Continuous records of the atmospheric greenhouse gases (GHGs CO2, CH4, and N2O are necessary input data for transient climate simulations, and their associated radiative forcing represents important components in analyses of climate sensitivity and feedbacks. Since the available data from ice cores are discontinuous and partly ambiguous, a well-documented decision process during data compilation followed by some interpolating post-processing is necessary to obtain those desired time series. Here, we document our best possible data compilation of published ice core records and recent measurements on firn air and atmospheric samples spanning the interval from the penultimate glacial maximum ( ∼  156 kyr BP to the beginning of the year 2016 CE. We use the most recent age scales for the ice core data and apply a smoothing spline method to translate the discrete and irregularly spaced data points into continuous time series. These splines are then used to compute the radiative forcing for each GHG using well-established, simple formulations. We compile only a Southern Hemisphere record of CH4 and discuss how much larger a Northern Hemisphere or global CH4 record might have been due to its interpolar difference. The uncertainties of the individual data points are considered in the spline procedure. Based on the given data resolution, time-dependent cutoff periods of the spline, defining the degree of smoothing, are prescribed, ranging from 5000 years for the less resolved older parts of the records to 4 years for the densely sampled recent years. The computed splines seamlessly describe the GHG evolution on orbital and millennial timescales for glacial and glacial–interglacial variations and on centennial and decadal timescales for anthropogenic times. Data connected with this paper, including raw data and final splines, are available at doi:10.1594/PANGAEA.871273.

  5. Effects of hydroxyl-functionalization and sub-Tg thermal annealing on high pressure pure- and mixed-gas CO2/CH4 separation by polyimide membranes based on 6FDA and triptycene-containing dianhydrides

    KAUST Repository

    Swaidan, Raja; Ghanem, Bader; Litwiller, Eric; Pinnau, Ingo

    2015-01-01

    -structure engaged in inter-chain charge transfer complexes (CTCs), similar to that of low-free-volume 6FDA-APAF polyimide. The isosteric heat of adsorption of CO2 as well as CO2/CH4 solubility selectivities varied negligibly upon replacement of OH with CH3 but CTC

  6. Soil CO2 CH4 and N2O fluxes from an afforested lowland raised peatbog in Scotland: implications for drainage and restoration

    Directory of Open Access Journals (Sweden)

    J. I. L. Morison

    2013-02-01

    Full Text Available The effect of tree (lodgepole pine planting with and without intensive drainage on soil greenhouse gas (GHG fluxes was assessed after 45 yr at a raised peatbog in West Flanders Moss, central Scotland. Fluxes of CO2 CH4 and N2O from the soil were monitored over a 2-yr period every 2 to 4 weeks using the static opaque chamber method in a randomised experimental block trial with the following treatments: drained and planted (DP, undrained and planted (uDP, undrained and unplanted (uDuP and for reference also from an adjoining near-pristine area of bog at East Flanders Moss (n-pris. There was a strong seasonal pattern in both CO2 and CH4 effluxes which were significantly higher in late spring and summer months because of warmer temperatures. Effluxes of N2O were low and no significant differences were observed between the treatments. Annual CH4 emissions increased with the proximity of the water table to the soil surface across treatments in the order: DP 4 m−2 yr−1, respectively. For CO2, effluxes increased in the order uDP 2 m−2 yr−1, respectively. CO2 effluxes dominated the total net GHG emission, calculated using the global warming potential (GWP of the three GHGs for each treatment (76–98%, and only in the n-pris site was CH4 a substantial contribution (23%. Based on soil effluxes only, the near pristine (n-pris peatbog had 43% higher total net GHG emission compared with the DP treatment because of high CH4 effluxes and the DP treatment had 33% higher total net emission compared with the uDP because drainage increased CO2 effluxes. Restoration is likely to increase CH4 emissions, but reduce CO2 effluxes. Our study suggests that if estimates of CO2 uptake by vegetation from similar peatbog sites were included, the total net GHG emission of restored peatbog would still be higher than that of the peatbog with trees.

  7. The IAGOS-core greenhouse gas package: a measurement system for continuous airborne observations of CO2, CH4, H2O and CO

    Directory of Open Access Journals (Sweden)

    Annette Filges

    2015-09-01

    flights and laboratory tests that document the performance for CO2, CH4, CO and water vapour measurements.

  8. Diffuse soil emission of hydrothermal gases (CO2, CH4, and C6H6) at Solfatara crater (Campi Flegrei, southern Italy)

    International Nuclear Information System (INIS)

    Tassi, F.; Nisi, B.; Cardellini, C.; Capecchiacci, F.; Donnini, M.; Vaselli, O.; Avino, R.; Chiodini, G.

    2013-01-01

    Highlights: • We present the first measurements of soil C 6 H 6 fluxes in a volcanic system. • Methane oxidation rate is controlled by soil gas fluxes. • Benzene oxidation rate is controlled by presence of a SO 4 2- rich aquifer. • Fumarolic emissions cause a strong benzene air contamination at a local scale. • Endogenous monoaromatics are detected in air samples from the whole crater. - Abstract: Measurements of soil fluxes of hydrothermal gases, with special emphasis on C 6 H 6 , as well as chemical composition of mono-aromatic compounds in fumaroles and air, were carried out in April 2012 at the Solfatara crater (Campi Flegrei, Southern Italy) to investigate the distribution and behavior of these species as they migrate through the soil from their deep source to the atmosphere. Soil fluxes of CO 2 , CH 4 and C 6 H 6 exhibit good spatial correlation, suggesting that diffuse degassing is mainly controlled by local fractures. The calculated total output of diffuse C 6 H 6 from Solfatara is 0.10 kg day −1 , whereas fluxes of CO 2 and CH 4 are 79 × 10 3 and 1.04 kg day −1 , respectively. A comparison between soil gas fluxes and fumarole composition reveals that within the crater soil CH 4 is significantly affected by oxidation processes, which are more efficient for low gas fluxes, being dependent on the residence time of the uprising hydrothermal gases at shallow depth. Benzene degradation, mainly proceeding through oxidation via benzoate, seems to be strongly controlled by the presence of a shallow SO 4 2- rich aquifer located in the central and southwestern sectors of the crater, suggesting that the process is particularly efficient when SO 4 2- acts as terminal electron acceptor (SO 4 reduction). Relatively high C 6 H 6 /C 7 H 8 ratios, typical of hydrothermal fluids, were measured in air close to the main fumarolic field of Solfatara crater. Here, C 6 H 6 concentrations, whose detection limit is ∼0.1 μg m −3 , are more than one order of

  9. Soil-atmospheric exchange of CO2, CH4, and N2O in three subtropical forest ecosystems in southern China

    Science.gov (United States)

    Tang, X.; Liu, S.; Zhou, G.; Zhang, Dongxiao; Zhou, C.

    2006-01-01

    The magnitude, temporal, and spatial patterns of soil-atmospheric greenhouse gas (hereafter referred to as GHG) exchanges in forests near the Tropic of Cancer are still highly uncertain. To contribute towards an improvement of actual estimates, soil-atmospheric CO2, CH4, and N2O fluxes were measured in three successional subtropical forests at the Dinghushan Nature Reserve (hereafter referred to as DNR) in southern China. Soils in DNR forests behaved as N2O sources and CH4 sinks. Annual mean CO2, N2O, and CH4 fluxes (mean ?? SD) were 7.7 ?? 4.6MgCO2-Cha-1 yr-1, 3.2 ?? 1.2 kg N2ONha-1 yr-1, and 3.4 ?? 0.9 kgCH4-Cha-1 yr-1, respectively. The climate was warm and wet from April through September 2003 (the hot-humid season) and became cool and dry from October 2003 through March 2004 (the cool-dry season). The seasonality of soil CO2 emission coincided with the seasonal climate pattern, with high CO2 emission rates in the hot-humid season and low rates in the cool-dry season. In contrast, seasonal patterns of CH4 and N2O fluxes were not clear, although higher CH4 uptake rates were often observed in the cool-dry season and higher N2O emission rates were often observed in the hot-humid season. GHG fluxes measured at these three sites showed a clear increasing trend with the progressive succession. If this trend is representative at the regional scale, CO2 and N2O emissions and CH4 uptake in southern China may increase in the future in light of the projected change in forest age structure. Removal of surface litter reduced soil CO2 effluxes by 17-44% in the three forests but had no significant effect on CH4 absorption and N2O emission rates. This suggests that microbial CH4 uptake and N2O production was mainly related to the mineral soil rather than in the surface litter layer. ?? 2006 Blackwell Publishing Ltd.

  10. Spatial variability of greenhouse gases emissions (CO2, CH4, N2O) in a tropical hydroelectric reservoir flooding primary forest (Petit Saut Reservoir, French Guiana)

    Science.gov (United States)

    Cailleaud, Emilie; Guérin, Frédéric; Bouillon, Steven; Sarrazin, Max; Serça, Dominique

    2014-05-01

    At the Petit Saut Reservoir (PSR, French Guiana, South America), vertical profiles were performed at 5 stations in the open waters (OW) and 6 stations in two shallow flooded forest (FF) areas between April 2012 and September 2013. Measurements included physico-chemical parameters, ammonium, nitrate and dissolved greenhouse gas (CO2, CH4, N2O) concentrations, dissolved and particulate organic carbon (DOC, POC) and nitrogen (PN), δ13C-POC and δ15N-PN . The diffusive fluxes were calculated from surface concentrations. The aim of this study was to estimate the spatial variations of greenhouse gas emissions at a dentrical hydroelectric reservoir located in the tropics and flooding primary forest. Twenty years after impoundment, the water column of the PSR is permanently and tightly stratified thermally in the FF whereas in the OW, the thermal gradients are not as stable. The different hydrodynamical behaviours between the two different zones have significant consequences on the biogeochemistry: oxygen barely diffuses down to the hypolimnion in the FF whereas destratification occurs sporadically during the rainy season in the OW. Although we found the same range of POC in the FF and the OW (2.5-29 μmol L-1) and 20% more DOC at the bottom of OW than in the FF (229-878 μmol L-1), CO2 and CH4 concentrations were always significantly higher in the FF (CO2: 11-1412 μmol L-1, CH4: 0.001-1015 μmol L-1) than in the OW. On average, the CO2 concentrations were 30-40% higher in the FF than in the OW and the CH4 concentrations were three times higher in the FF than in the OW. The δ13C-POC and C:N values did not suggest substantial differences in the sources of OM between the FF and OW. At all stations, POC at the bottom has an isotopic signature slightly lighter than the terrestrial OM in the surrounding forest whereas the isotopic signature of surface POM would result from phytoplankton and methanotrophs. The vertical profiles of nitrogen compounds reveal that the main

  11. Measurements of CO2, CH4, H2O, and HDO over a 2-km Outdoor Path with Dual-Comb Spectroscopy

    Science.gov (United States)

    Rieker, G. B.; Giorgetta, F. R.; Coddington, I.; Swann, W. C.; Sinclair, L. C.; Cromer, C.; Baumann, E.; Newbury, N. R.; Kofler, J.; Petron, G.; Sweeney, C.; Tans, P. P.

    2013-12-01

    We demonstrate simultaneous sensing of CO2, CH4, H2O, and HDO over a 2-km outdoor open air path using dual-frequency-comb absorption spectroscopy (DCS). Our implementation of the DCS technique simultaneously offers broad spectral coverage (>8 THz, 267 cm-1) and fine spectral point spacing (100 MHz, 0.0033 cm-1) with a coherent eye-safe beam. The spectrometer, which is adapted from [Zolot et al., 2012], consists of two mutually coherent Erbium-doped fiber frequency-comb lasers which create a broad spectrum of perfectly spaced narrow linewidth frequency elements (';comb teeth') near 1.6 μm. The comb light is transmitted by a telescope and active steering mirrors from the roof of the NIST Boulder laboratory to a 50-cm flat mirror located 1 km away. The return light is received by a second telescope and carried via multimode fiber to a detector. The greenhouse gas absorption attenuates the teeth from the two combs that are coincident with the relevant molecular resonant frequencies. We purposefully offset the frequencies between the two frequency combs in a Vernier-like fashion so that each pair of comb teeth from the two combs results in a unique rf heterodyne beat frequency on the photodiode. The spectral spacing between subsequent comb teeth pairs is 100 MHz, far lower than the ~4 GHz linewidths of small molecule absorption features in the atmosphere. Because of the narrow comb linewidth, there is an essentially negligible instrument lineshape. The measured absorption spectrum can thus resolve neighboring absorption features of different species, and can be compared directly with HITRAN and recent greenhouse gas absorption models developed for satellite- and ground-based carbon observatories to determine the path-integrated concentrations of the absorbing species. Measurements covering the complete 30013←00001 absorption band of CO2 and absorption features of CH4, H2O and HDO between 1.6-1.67 μm were performed under a variety of atmospheric conditions. During

  12. High pressure pure- and mixed-gas separation of CO2/CH4 by thermally-rearranged and carbon molecular sieve membranes derived from a polyimide of intrinsic microporosity

    KAUST Repository

    Swaidan, Raja

    2013-11-01

    Natural gas sweetening, one of the most promising venues for the growth of the membrane gas separation industry, is dominated by polymeric materials with relatively low permeabilities and moderate selectivities. One strategy towards improving the gas transport properties of a polymer is enhancement of microporosity either by design of polymers of intrinsic microporosity (PIMs) or by thermal treatment of polymeric precursors. For the first time, the mixed-gas CO2/CH4 transport properties are investigated for a complete series of thermally-rearranged (TR) (440°C) and carbon molecular sieve (CMS) membranes (600, 630 and 800°C) derived from a polyimide of intrinsic microporosity (PIM-6FDA-OH). The pressure dependence of permeability and selectivity is reported up to 30bar for 1:1, CO2:CH4 mixed-gas feeds at 35°C. The TR membrane exhibited ~15% higher CO2/CH4 selectivity relative to pure-gas feeds due to reductions in mixed-gas CH4 permeability reaching 27% at 30bar. This is attributed to increased hindrance of CH4 transport by co-permeation of CO2. Interestingly, unusual increases in mixed-gas CH4 permeabilities relative to pure-gas values were observed for the CMS membranes, resulting in up to 50% losses in mixed-gas selectivity over the applied pressure range. © 2013 Elsevier B.V.

  13. Net exchanges of CO2, CH4 and N2O between the terrestrial ecosystems and the atmosphere in boreal and arctic region: Towards a full greenhouse gas budget

    Science.gov (United States)

    Zhang, B.; Tian, H.; Lu, C.; Yang, J.; Kamaljit, K.; Pan, S.

    2014-12-01

    Boreal and arctic terrestrial ecosystem is a unique ecological region due to large portion of wetland and permafrost distribution. Increasing disturbances, like permafrost-thaw, fire event, climate extreme, would greatly change the patterns and variations of greenhouse gas emission and further affect the feedback between terrestrial ecosystem and climate change. Carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) accounted for more than 85% of the radioactive forcing (RF) due to long-lived greenhouse gases. However, few studies have considered the full budget of three gases together in this region. In this study, we used a process-based model (Dynamic Land Ecosystem Model), driven by multiple global change factors, to quantify the magnitude, spatial and temporal variation of CO2, CH4 and N2O across the boreal and arctic regions. Simulated results have been evaluated against field observations, inventory-based and atmospheric inversion estimates. By implementing a set of factorial simulations, we further quantify the relative contribution of climate, atmospheric composition, fire to the CO2, CH4 and N2O fluxes. Continued warming climate potentially could shift the inter-annual and intra-annual variation of greenhouse gases fluxes. The understanding of full budget in this region could provide insights for reasonable future projection, which is also crucial for developing effective mitigation strategies.

  14. Distribution of dissolved green-house gases (CO2, CH4, N2O) in Lakes Edward and George: Results from the first field cruise of the HIPE project

    Science.gov (United States)

    Borges, Alberto V.; Morana, Cédric D. T.; Lambert, Thibault; Okello, William; Bouillon, Steven

    2017-04-01

    Inland waters (streams, rivers, lakes, reservoirs) are quantitatively important components of the global budgets of atmospheric emissions of long-lived greenhouse gases (GHGs) (CO2, CH4, N2O). Available data indicate that a very large fraction of CO2 and CH4 emissions from rivers and reservoirs occurs at tropical latitudes. Data on GHGs at tropical latitudes from lakes however are much more scarse, and the relative importance of emissions, in particular in Africa, remains to be determined. Large tropical lakes are net autotrophic (hence potentially sinks for atmospheric CO2) due generally low dissolved organic carbon concentrations, seasonally near constant light and temperature conditions, and generally deep water columns favourable for export of organic matter to depth. This sharply contrasts with their much better documented temperate and boreal counterparts, usually considered as CO2 sources to the atmosphere sustained by net heterotrophy. Here, we report a data-set of dissolved CO2, CH4, N2O obtained in October 2016 in Lakes Edward and George and adjacent streams and crater lakes in the frame of Belgian Science Policy (BELSPO) HIPE (Human impacts on ecosystem health and resources of Lake Edward, http://www.co2.ulg.ac.be/hipe/) project. Lake George and part of Lake Edward were sinks for atmospheric CO2 and N2O due to high primary production and denitrification in sediments, respectively, and modest sources of CH4 to the atmosphere. Sampled rivers and streams were oversaturated in CO2 and CH4 and close to atmospheric equilibrium with regards to N2O. Spatial variations within rivers and streams were related to elevation and vegetation characteristics on the catchments (savannah versus forest). Levels of CO2, CH4, and N2O were within the range of those we reported in other African rivers. Crater lakes acted as sinks for atmospheric CO2 and N2O but were extremely over-saturated in CH4, due to intense primary production sustained by cyanobacteria. These CH4 levels

  15. Continuous multi-plot measurements of CO2, CH4, N2O and H2O in a managed boreal forest - The importance of accounting for all greenhouse gases

    Science.gov (United States)

    Vestin, P.; Mölder, M.; Sundqvist, E.; Båth, A.; Lehner, I.; Weslien, P.; Klemedtsson, L.; Lindroth, A.

    2015-12-01

    In order to assess the effects of different management practices on the exchange of greenhouse gases (GHG), it is desirable to perform repeated and parallel measurements on both experimental and control plots. Here we demonstrate how a system system combining eddy covariance and gradient techniques can be used to perform this assessment in a managed forest ecosystem.The net effects of clear-cutting and stump harvesting on GHG fluxes were studied at the ICOS site Norunda, Sweden. Micrometeorological measurements (i.e., flux-gradient measurements in 3 m tall towers) allowed for quantification of CO2, CH4 and H2O fluxes (from May 2010) as well as N2O and H2O fluxes (from June 2011) at two stump harvested plots and two control plots. There was one wetter and one drier plot of each treatment. Air was continuously sampled at two heights in the towers and gas concentrations were analyzed for CH4, CO2, H2O (LGR DLT-100, Los Gatos Research) and N2O, H2O (QCL Mini Monitor, Aerodyne Research). Friction velocities and sensible heat fluxes were measured by sonic anemometers (Gill Windmaster, Gill Instruments Ltd). Automatic chamber measurements (CO2, CH4, H2O) were carried out in the adjacent forest stand and at the clear-cut during 2010.Average CO2 emissions for the first year ranged between 14.4-20.2 ton CO2 ha-1 yr-1. The clear-cut became waterlogged after harvest and a comparison of flux-gradient data and chamber data (from the adjacent forest stand) indicated a switch from a weak CH4 sink to a significant source at all plots. The CH4 emissions ranged between 0.8-4.5 ton CO2-eq. ha-1 yr-1. N2O emissions ranged between 0.4-2.6 ton CO2-eq. ha-1 yr-1. Enhanced N2O emission on the drier stump harvested plot was the only clear treatment effect on GHG fluxes that was observed. Mean CH4 and N2O emissions for the first year of measurements amounted up to 29% and 20% of the mean annual CO2 emissions, respectively. This highlights the importance of including all GHGs when assessing

  16. Soil CO2, CH4 and N2O effluxes and concentrations in soil profiles down to 15.5m depth in eucalypt plantations under contrasted rainfall regimes

    Science.gov (United States)

    Germon, A.; Nouvellon, Y.; Christophe, J.; Chapuis-Lardy, L.; Robin, A.; Rosolem, C. A.; Gonçalves, J. L. D. M.; Guerrini, I. A.; Laclau, J. P.

    2017-12-01

    Silvicultural practices in planted forests affect the fluxes of greenhouse gases at the soil surface and the major factors driving greenhouse gas production in forest soils (substrate supply, temperature, water content,…) vary with soil depth. Our study aimed to assess the consequences of drought on the temporal variability of CO2, CH4 and N2O fluxes throughout very deep soil profiles in Eucalyptus grandis plantations 3 months before the harvest then in coppice, the first 18 months after clear-cutting. Two treatments were compared: one with 37% of throughfall excluded by plastic sheets (TE), and one without rainfall exclusion (WE). Measurements of soil CO2 efflux were made every two weeks for 30 months using a closed-path Li8100 system in both treatment. Every two weeks for 21 months, CO2, CH4 and N2O surface effluxes were measured using the closed-chamber method and concentrations in the soil were measured at 7 depths down to 15.5 m in both TE and WE. At most measurement dates, soil CO2 efflux were significantly higher in TE than in WE. Across the two treatments and the measurement dates, CO2 concentrations increased from 4446 ± 2188 ppm at 10 cm deep to 15622 ± 3523 ppm at 15.5 m, CH4 concentrations increased from 0.41 ± 0.17 ppm at 10 cm deep to 0.77 ± 0.24 ppm at 15.5 m and N2O concentrations remained roughly constant and were on average 478 ± 55 ppb between soil surface and 15.5 m deep. CO2 and N2O concentrations were on average 20.7 and 7.6% lower in TE than in WE, respectively, across the sampling depths. However, CH4 concentrations in TE were on average 44.4% higher than in WE, throughout the soil profile. Those results suggest that extended drought periods might reduce the production of CO2 and N2O but increase the accumulation of CH4 in eucalypt plantations established in deep tropical soils. Very deep tropical soils cover huge areas worldwide and improving our understanding of the spatiotemporal dynamics of gas concentrations in deep soil layers

  17. Effects of Climate Change and Organic Matter Amendments on the Fate of Soil Carbon and the Global Warming Potential of CO2, CH4, and N2O Emissions in an Upland Soil

    Science.gov (United States)

    Simmonds, M.; Muehe, E. M.; Fendorf, S. E.

    2017-12-01

    Our current understanding of the mechanisms driving carbon stabilization in soil organic matter (SOM) and its release to the atmosphere is insufficient for predicting the response of soil carbon dynamics to future climatic conditions. The persistence of SOM has been studied primarily within the context of biochemical, physical, and geochemical protection from decomposition. More recently, bioenergetic constraints on SOM decomposition due to oxygen limitations have been demonstrated in submerged soils. However, the relevance of anaerobic domains in upland soils is uncertain. To better understand how upland soils will respond to climate change, we conducted a 52-day incubation of an upland soil at constant soil moisture (field capacity) under varying air temperatures (32°C and 37°C), CO2 concentrations (398 and 850 ppmv), and soil organic carbon contents (1.3%, 2.4%). Overall, we observed a stimulatory effect of future climate (elevated temperature and CO2) and higher carbon inputs on net SOM mineralization rates (higher CO2, CH4 and N2O emissions). Importantly, CH4 emissions were observed in the soils with added plant residue, indicating anaerobic microsites are relevant in upland soils, and significantly impact microbial respiration pathways, rates of SOM mineralization, and the global warming potential of trace gas emissions. These findings have important implications for positive soil carbon-climate feedbacks, and warrant further investigation into representing anaerobic soil domains of upland soils in biogeochemical models.

  18. Charge transfer processes in collisions of H+ ions with H2, D2, CO, CO2 CH4, C2H2, C2H6 and C3H8 molecules below 10 keV

    International Nuclear Information System (INIS)

    Kusakabe, T.; Buenker, R.J.; Kimura, M.

    2002-01-01

    Charge transfer processes resulting from collisions of H + ions with H 2 , D 2 , CO, CO 2 CH 4 , C 2 H 2 , C 2 H 6 and C 3 H 8 molecules have been investigated in the energy range of 0.2 to 4.0 keV experimentally and theoretically. The initial growth rate method was employed in the experiment for studying the dynamics and cross sections. Theoretical analysis based on a molecular-orbital expansion method for H 2 , D 2 , CO, CH 4 and C 2 H 2 targets was also carried out. The present results for the H 2 , CO and CO 2 molecules by H + impact are found to be in excellent accord with most of previous measurements above 1 keV, but they show some differences below this energy where our result displays a stronger energy-dependence. For CH 4 , C 2 H 2 , C 2 H 6 and C 3 H 8 targets, both experimental and theoretical results indicate that if one assumes vibrationally excited molecular ions (CH 4 + , C 2 H 2 + , C 2 H 6 + and C 3 H 8 + ) formed in the exit channel, then charge transfer processes sometimes become more favorable since these vibrationally excited fragments meet an accidental resonant condition. This is a clear indication of the role of vibrational excited states for charge transfer, and is an important realization for general understanding. (author)

  19. Greenhouse effect gases sources and sinks (CO2, CH4, N2O) in grasslands and reduction strategies. Greenhouse effect gases prairies. Final report of the second part of the project. April 2004

    International Nuclear Information System (INIS)

    Soussana, J.F.

    2004-04-01

    The project 'GES-Prairies' (Greenhouse Gases - Grasslands) had two main objectives: 1. To measure more accurately the fluxes of CO 2 , CH 4 and N 2 O of French grasslands and determine the greenhouse gas (GHG) balance of these areas. 2. To calculate the net GHG emissions of cattle production farms and finally to propose and evaluate some management scenarios leading to a reduction of GHG emissions. This project deals with three different spatial scales: the field scale, the farm scale and finally, the regional scale. At the field scale, during two years, fluxes of CO 2 , CH 4 and N 2 O were measured in a mid-mountain permanent grassland, previously managed intensively by cutting and grazing (Laqueuille, Auvergne, France). Results from the first complete year of measurements show that the extensification process (reduction of the stocking rate and stopping N fertilization) allows to stock more carbon in the ecosystem. At the farm scale, We developed a model (FARMSIM, coupled to PASIM) able to simulate the GHG balance of a livestock farm. FARMSIM has been tested with data obtained from a mixed livestock farm in Lorraine (dairy and meat production, annual average stocking rate = 1.3 LU ha -1 ) of 100 ha (including 76 ha of grasslands and 21 of annual crops). The results indicate a net emission of 175 t equivalent C-CO 2 for this farm. If expressed per unit of product, it represents 1.34 t equivalent C-CO 2 per LU and per year or 0.54 kg CO 2 per kg of milk and per year. At the regional scale/. The PASIM model has been used to simulate the European grasslands with a spatial resolution of 1' (about 200 * 200 km). For each grid cell, a sensibility analysis allowed to determine the N application which correspond to 30% of the N application that would maximize the annual yield of the pasture. Simulation runs on mixed systems (combining grazing and cutting) show that almost one half of the grassland area is, on average, used for cutting. These simulations predict N 2 O

  20. A Portable FTIR Analyser for Field Measurements of Trace Gases and their Isotopologues: CO2, CH4, N2O, CO, del13C in CO2 and delD in water vapour

    Science.gov (United States)

    Griffith, D. W.; Bryant, G. R.; Deutscher, N. M.; Wilson, S. R.; Kettlewell, G.; Riggenbach, M.

    2007-12-01

    We describe a portable Fourier Transform InfraRed (FTIR) analyser capable of simultaneous high precision analysis of CO2, CH4, N2O and CO in air, as well as δ13C in CO2 and δD in water vapour. The instrument is based on a commercial 1 cm-1 resolution FTIR spectrometer fitted with a mid-IR globar source, 26 m multipass White cell and thermoelectrically-cooled MCT detector operating between 2000 and 7500 cm-1. Air is passed through the cell and analysed in real time without any pre-treatment except for (optional) drying. An inlet selection manifold allows automated sequential analysis of samples from one or more inlet lines, with typical measurement times of 1-10 minutes per sample. The spectrometer, inlet sampling sequence, real-time quantitative spectrum analysis, data logging and display are all under the control of a single program running on a laptop PC, and can be left unattended for continuous measurements over periods of weeks to months. Selected spectral regions of typically 100-200 cm-1 width are analysed by a least squares fitting technique to retrieve concentrations of trace gases, 13CO2 and HDO. Typical precision is better than 0.1% without the need for calibration gases. Accuracy is similar if measurements are referenced to calibration standard gases. δ13C precision is typically around 0.1‰, and for δD it is 1‰. Applications of the analyser include clean and polluted air monitoring, tower-based flux measurements such as flux gradient or integrated horizontal flux measurements, automated soil chambers, and field-based measurements of isotopic fractionation in soil-plant-atmosphere systems. The simultaneous multi-component advantages can be exploited in tracer-type emission measurements, for example of CH4 from livestock using a co-released tracer gas and downwind measurement. We have also developed an open path variant especially suited to tracer release studies and measurements of NH3 emissions from agricultural sources. An illustrative

  1. Potential for negative emissions of greenhouse gases (CO2, CH4 and N2O) through coastal peatland re-establishment: Novel insights from high frequency flux data at meter and kilometer scales

    Science.gov (United States)

    Windham-Myers, Lisamarie; Bergamaschi, Brian; Anderson, Frank; Knox, Sara; Miller, Robin; Fujii, Roger

    2018-04-01

    High productivity temperate wetlands that accrete peat via belowground biomass (peatlands) may be managed for climate mitigation benefits due to their global distribution and notably negative emissions of atmospheric carbon dioxide (CO2) through rapid storage of carbon (C) in anoxic soils. Net emissions of additional greenhouse gases (GHG)—methane (CH4) and nitrous oxide (N2O)—are more difficult to predict and monitor due to fine-scale temporal and spatial variability, but can potentially reverse the climate mitigation benefits resulting from CO2 uptake. To support management decisions and modeling, we collected continuous 96 hour high frequency GHG flux data for CO2, CH4 and N2O at multiple scales—static chambers (1 Hz) and eddy covariance (10 Hz)—during peak productivity in a well-studied, impounded coastal peatland in California’s Sacramento Delta with high annual rates of C fluxes, sequestering 2065 ± 150 g CO2 m‑2 y‑1 and emitting 64.5 ± 2.4 g CH4 m‑2 y‑1. Chambers (n = 6) showed strong spatial variability along a hydrologic gradient from inlet to interior plots. Daily (24 hour) net CO2 uptake (NEE) was highest near inlet locations and fell dramatically along the flowpath (‑25 to ‑3.8 to +2.64 g CO2 m‑2 d‑1). In contrast, daily net CH4 flux increased along the flowpath (0.39 to 0.62 to 0.88 g CH4 m‑2 d‑1), such that sites of high daily CO2 uptake were sites of low CH4 emission. Distributed, continuous chamber data exposed five novel insights, and at least two important datagaps for wetland GHG management, including: (1) increasing dominance of CH4 ebullition fluxes (15%–32% of total) along the flowpath and (2) net negative N2O flux across all sites as measured during a 4 day period of peak biomass (‑1.7 mg N2O m‑2 d‑1 0.51 g CO2 eq m‑2 d‑1). The net negative emissions of re-established peat-accreting wetlands are notably high, but may be poorly estimated by

  2. Characterization of trace gases measured over Alberta oil sands mining operations: 76 speciated C2-C10 volatile organic compounds (VOCs), CO2, CH4, CO, NO, NO2, NOy, O3 and SO2

    Science.gov (United States)

    Simpson, I. J.; Blake, N. J.; Barletta, B.; Diskin, G. S.; Fuelberg, H. E.; Gorham, K.; Huey, L. G.; Meinardi, S.; Rowland, F. S.; Vay, S. A.; Weinheimer, A. J.; Yang, M.; Blake, D. R.

    2010-12-01

    Oil sands comprise 30% of the world's oil reserves and the crude oil reserves in Canada's oil sands deposits are second only to Saudi Arabia. The extraction and processing of oil sands is much more challenging than for light sweet crude oils because of the high viscosity of the bitumen contained within the oil sands and because the bitumen is mixed with sand and contains chemical impurities such as sulphur. Despite these challenges, the importance of oil sands is increasing in the energy market. To our best knowledge this is the first peer-reviewed study to characterize volatile organic compounds (VOCs) emitted from Alberta's oil sands mining sites. We present high-precision gas chromatography measurements of 76 speciated C2-C10 VOCs (alkanes, alkenes, alkynes, cycloalkanes, aromatics, monoterpenes, oxygenated hydrocarbons, halocarbons and sulphur compounds) in 17 boundary layer air samples collected over surface mining operations in northeast Alberta on 10 July 2008, using the NASA DC-8 airborne laboratory as a research platform. In addition to the VOCs, we present simultaneous measurements of CO2, CH4, CO, NO, NO2, NOy, O3 and SO2, which were measured in situ aboard the DC-8. Carbon dioxide, CH4, CO, NO, NO2, NOy, SO2 and 53 VOCs (e.g., non-methane hydrocarbons, halocarbons, sulphur species) showed clear statistical enhancements (1.1-397×) over the oil sands compared to local background values and, with the exception of CO, were greater over the oil sands than at any other time during the flight. Twenty halocarbons (e.g., CFCs, HFCs, halons, brominated species) either were not enhanced or were minimally enhanced (industry fell into two groups: (1) evaporative emissions from the oil sands and its products and/or from the diluent used to lower the viscosity of the extracted bitumen (i.e., C4-C9 alkanes, C5-C6 cycloalkanes, C6-C8 aromatics), together with CO; and (2) emissions associated with the mining effort, such as upgraders (i.e., CO2, CO, CH4, NO, NO2, NOy

  3. Thermal electron mobilities in low density gaseous mixtures

    International Nuclear Information System (INIS)

    Dmitriev, O.W.; Tchorzewska, W.; Szamrej, I.; Forys, M.

    1992-01-01

    A new method of obtaining thermal electron mobilities from experimental dependencies observed in the electron swarm is described; the method is suitable for both electron accepting and non-accepting systems. The electron mobilities for CO 2 , CH 4 C 2 H 6 as well as for N 2 , Ar, Xe, Kr and their mixtures with carbon dioxide are obtained. (Author)

  4. Modeling Plasma-based CO2 and CH4 Conversion in Mixtures with N2, O2 and H2O: the Bigger Plasma Chemistry Picture

    KAUST Repository

    Wang, Weizong; Snoeckx, Ramses; Zhang, Xuming; Cha, Min; Bogaerts, Annemie

    2018-01-01

    performed regarding the single component gases, i.e. CO2 splitting and CH4 reforming, as well as for two component mixtures, i.e. dry reforming of methane (CO2/CH4), partial oxidation of methane (CH4/O2), artificial photosynthesis (CO2/H2O), CO2

  5. Inter-annual variability and trend detection of urban CO2, CH4 and CO emissions

    Science.gov (United States)

    Lauvaux, T.; Deng, A.; Gurney, K. R.; Nathan, B.; Ye, X.; Oda, T.; Karion, A.; Hardesty, M.; Harvey, R. M.; Richardson, S.; Whetstone, J. R.; Hutyra, L.; Davis, K. J.; Brewer, A.; Gaudet, B. J.; Turnbull, J. C.; Sweeney, C.; Shepson, P. B.; Miles, N.; Bonin, T.; Wu, K.; Balashov, N. V.

    2017-12-01

    The Indianapolis Flux (INFLUX) Experiment has conducted an unprecedented volume of atmospheric greenhouse gas measurements across the Indianapolis metropolitan area from aircraft, remote-sensing, and tower-based observational platforms. Assimilated in a high-resolution urban inversion system, atmospheric data provide an independent constraint to existing emission products, directly supporting the integration of economic data into urban emission systems. We present here the first multi-year assessment of carbon dioxide (CO2), methane (CH4), and carbon monoxide (CO) emissions from anthropogenic activities in comparison to multiple bottom-up emission products. Biogenic CO2 fluxes are quantified using an optimized biogeochemical model at high resolution, further refined within the atmospheric inversion system. We also present the first sector-based inversion by jointly assimilating CO2 and CO mixing ratios to quantify the dominant sectors of emissions over the entire period (2012-2015). The detected trend in CO2 emissions over 2012-2015 from both bottom-up emission products and tower-based inversions agree within a few percent, with a decline in city emissions over the 3-year time period. Major changes occur at the primary power plant, suggesting a decrease in energy production within the city limits. The joint assimilation of CO2 and CO mixing ratios confirms the absence of trends in other sectors. However, top-down and bottom-up approaches tend to disagree annually, with a decline in urban emissions suggested by atmospheric data in 2014 that is several months earlier than is observed in the bottom-up products. Concerning CH4 emissions, the inversion shows a decrease since mid-2014 which may be due to lower landfill emissions or lower energy consumption (from coal and natural gas). This first demonstration of a high-accuracy long-term greenhouse gas measurement network merged with a high-resolution bottom-up information system highlights the potential for informing and supporting policy makers on the successful implementation of emission reduction targets. We show here how the combination of information sources supports the evaluation of mitigation policies and helps development of understanding regarding the mechanisms driving emission trends at the level of economical sectors.

  6. BOREAS TGB-5 CO2, CH4 and CO Chamber Flux Data Over the NSA

    Science.gov (United States)

    Burke, Roger; Hall, Forrest G. (Editor); Conrad, Sara K. (Editor); Zepp, Richard

    2000-01-01

    The BOReal Ecosystem-Atmosphere Study Trace Gas Biogeochemistry (BOREAS TGB-5) team collected a variety of trace gas concentration and flux measurements at several NSA sites. This data set contains carbon dioxide (CO2), methane (CH4), and carbon monoxide (CO) chamber flux measurements conducted in 1994 at upland forest sites that experienced stand-replacement fires. These measurements were acquired to understand the impact of fires on soil biogeochemistry and related changes in trace gas exchange in boreal forest soils. Relevant ancillary data, including data concerning the soil temperature, solar irradiance, and information from nearby un-burned control sites, are included to provide a basis for modeling the regional impacts of fire and climate changes on trace gas biogeochemistry. The data are provided in tabular ASCII files.

  7. Electrochemical study of chemical properties in ethanolamine and its mixtures with water; Etude electrochimique de proprietes chimiques dans l'ethanolamine et ses melanges avec l'eau

    Energy Technology Data Exchange (ETDEWEB)

    Grall, M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1964-12-01

    This work is concerned with the study of acid-base reactions and of complex formation in ethanolamine and its mixtures with water. The ionic product of the solvent has been determined by an electro-chemical study of the H{sup +}/H{sub 2} system. The reduction curves for ethanolamine-water mixtures, for different acidities, have made it possible to follow the variations in the size of the pH domain as a function of the composition of the solvent. The form of this variation has been explained on the basis of the dielectric constant and the solvation of the proton by the ethanolamine. In the second part, the electrochemical systems of mercury have been studied by anodic polarography. In order to establish a parallel between the acid-base reactions and complex formation reactions, we have studied the stability of Hg (CN){sub 2} in water-ethanolamine mixtures. It has been possible to deduce the law for the variation of pK{sub c} with solvent composition. The representative graph of this function passes through a minimum for a proportion of about 50 per cent of ethanolamine as in the case of acids. This variation has been explained by the predominating influence of {epsilon} for ethanolamine propositions of over 50 per cent and by that of the solvation of Hg{sup 2+} for proportions of under 50 per cent. (author) [French] Ce travail porte sur l'etude des reactions acides-bases et de formation de complexes dans l'ethanolamine et ses melanges avec l'eau. Le produit ionique du solvant a pu etre determine par l'etude electro-chimique du systeme H{sup +}/H{sub 2}. Les courbes de reduction des melanges ethanolamine-eau, pour des acidites variables, ont permis de suivre les variations de l'etendue du domaine de pH, en fonction de la composition du solvant. L'allure de cette variation a ete expliquee en faisant intervenir la constante dielectrique et la solvatation du proton par l'ethanolamine. Dans une deuxieme partie, les systemes electrochimiques du mercure ont ete etudies par

  8. Mixture

    Directory of Open Access Journals (Sweden)

    Silva-Aguilar Martín

    2011-01-01

    Full Text Available Metals are ubiquitous pollutants present as mixtures. In particular, mixture of arsenic-cadmium-lead is among the leading toxic agents detected in the environment. These metals have carcinogenic and cell-transforming potential. In this study, we used a two step cell transformation model, to determine the role of oxidative stress in transformation induced by a mixture of arsenic-cadmium-lead. Oxidative damage and antioxidant response were determined. Metal mixture treatment induces the increase of damage markers and the antioxidant response. Loss of cell viability and increased transforming potential were observed during the promotion phase. This finding correlated significantly with generation of reactive oxygen species. Cotreatment with N-acetyl-cysteine induces effect on the transforming capacity; while a diminution was found in initiation, in promotion phase a total block of the transforming capacity was observed. Our results suggest that oxidative stress generated by metal mixture plays an important role only in promotion phase promoting transforming capacity.

  9. Stress-strain response of pre-compacted granular coal samples exposed to CO2, CH4, He and Ar

    NARCIS (Netherlands)

    Bergen, F. van; Hol, S.; Spiers, C.J.

    2011-01-01

    The interaction between supercritical carbon dioxide and coal has been the subject of many studies in recent years. This paper reports two different types of swelling experiments, one on confined and one on unconfined samples of pre-pressed, crushed bituminous coal, performed at gas or fluid

  10. Temporal and spatial variations of soil CO2, CH4 and N2O fluxes at three differently managed grasslands

    Directory of Open Access Journals (Sweden)

    D. Imer

    2013-09-01

    Full Text Available A profound understanding of temporal and spatial variabilities of soil carbon dioxide (CO2, methane (CH4 and nitrous oxide (N2O fluxes between terrestrial ecosystems and the atmosphere is needed to reliably quantify these fluxes and to develop future mitigation strategies. For managed grassland ecosystems, temporal and spatial variabilities of these three soil greenhouse gas (GHG fluxes occur due to changes in environmental drivers as well as fertilizer applications, harvests and grazing. To assess how such changes affect soil GHG fluxes at Swiss grassland sites, we studied three sites along an altitudinal gradient that corresponds to a management gradient: from 400 m a.s.l. (intensively managed to 1000 m a.s.l. (moderately intensive managed to 2000 m a.s.l. (extensively managed. The alpine grassland was included to study both effects of extensive management on CH4 and N2O fluxes and the different climate regime occurring at this altitude. Temporal and spatial variabilities of soil GHG fluxes and environmental drivers on various timescales were determined along transects of 16 static soil chambers at each site. All three grasslands were N2O sources, with mean annual soil fluxes ranging from 0.15 to 1.28 nmol m−2 s−1. Contrastingly, all sites were weak CH4 sinks, with soil uptake rates ranging from −0.56 to −0.15 nmol m−2 s−1. Mean annual soil and plant respiration losses of CO2, measured with opaque chambers, ranged from 5.2 to 6.5 μmol m−2 s−1. While the environmental drivers and their respective explanatory power for soil N2O emissions differed considerably among the three grasslands (adjusted r2 ranging from 0.19 to 0.42, CH4 and CO2 soil fluxes were much better constrained (adjusted r2 ranging from 0.46 to 0.80 by soil water content and air temperature, respectively. Throughout the year, spatial heterogeneity was particularly high for soil N2O and CH4 fluxes. We found permanent hot spots for soil N2O emissions as well as locations of permanently lower soil CH4 uptake rates at the extensively managed alpine site. Including hot spots was essential to obtain a representative mean soil flux for the respective ecosystem. At the intensively managed grassland, management effects clearly dominated over effects of environmental drivers on soil N2O fluxes. For CO2 and CH4, the importance of management effects did depend on the status of the vegetation (LAI.

  11. Development of differential absorption lidar (DIAL) for detection of CO2, CH4 and PM in Alberta

    Science.gov (United States)

    Wojcik, Michael; Crowther, Blake; Lemon, Robert; Valupadas, Prasad; Fu, Long; Leung, Bonnie; Yang, Zheng; Huda, Quamrul; Chambers, Allan

    2005-05-01

    Rapid expansion of the oil and gas industry in Alberta, including the oil sands, has challenged the Alberta Government to keep pace in its efforts to monitor and mitigate the environmental impacts of development. The limitations of current monitoring systems has pushed the provincial government to seek out advanced sensing technologies such as satellite imagery and laser based sensors. The Space Dynamics Laboratory (SDL) of Utah State University, in cooperation with Alberta Environmental Monitoring, Evaluation and Reporting Agency (AEMERA), has developed North America's first mobile differential absorption lidar (DIAL) system designed specifically for emissions measurement. This instrument is housed inside a 36' trailer which allows for mobility to travel across Alberta to characterize source emissions and to locate fugitive leaks. DIAL is capable of measuring concentrations for carbon dioxide (CO2) and methane (CH4) at ranges of up to 3 km with a spatial resolution of 10 meters. DIAL can map both CO2 and CH4, as well as particulate matter (PM) in a linear fashion; by scanning the laser beam in both azimuth and elevation DIAL can create images of emissions in two dimensions. DIAL imagery may be used to understand and control production practices, characterize source emissions, determine emission factors, locate fugitive leaks, assess plume dispersion, and confirm air dispersion modeling. A system overview of the DIAL instrument and some representative results will be discussed.

  12. Application of biochar and nitrogen influences fluxes of CO2, CH4 and N2O in a forest soil.

    Science.gov (United States)

    Hawthorne, Iain; Johnson, Mark S; Jassal, Rachhpal S; Black, T Andrew; Grant, Nicholas J; Smukler, Sean M

    2017-05-01

    Nitrogen (N) fertilization of forests for increasing carbon sequestration and wood volume is expected to influence soil greenhouse gas (GHG) emissions, especially to increase N 2 O emissions. As biochar application is known to affect soil GHG emissions, we investigated the effect of biochar application, with and without N fertilization, to a forest soil on GHG emissions in a controlled laboratory study. We found that biochar application at high (10%) application rates increased CO 2 and N 2 O emissions when applied without urea-N fertilizer. At both low (1%) and high biochar (10%) application rates CH 4 consumption was reduced when applied without urea-N fertilizer. Biochar application with urea-N fertilization did not increase CO 2 emissions compared to biochar amended soil without fertilizer. In terms of CO 2 -eq, the net change in GHG emissions was mainly controlled by CO 2 emissions, regardless of treatment, with CH 4 and N 2 O together accounting for less than 1.5% of the total emissions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. A measurement system for continuous observations of CO2, CH4, H2O and CO onboard passenger aircraft

    Science.gov (United States)

    Gerbig, Christoph; Filges, Annette; Franke, Harald; Klaus, Christoph; Chen, Huilin

    2013-04-01

    Improved quantification and understanding of surface-atmosphere exchange fluxes of greenhouse gases (GHGs) caused by natural as well as anthropogenic processes is of paramount importance in a world of a changing climate and ever increasing emissions. Top-down estimation of GHG fluxes is traditionally done by inverse transport modeling, using GHG observations from a global network of stations. Uncertainties in modeled vertical transport rates (moist convection, turbulent mixing, stratosphere-troposphere exchange) however greatly affect the quality of flux estimates. More recently, remote sensing of vertical column mole fractions of GHGs have become available for inverse modeling, reducing the impact of vertical transport uncertainties to first order. However, those need validation against in-situ observations. A strategy for regular, global in-situ atmospheric profiling of GHGs, covering at least the troposphere, is thus needed to provide validation of remote sensing and of forward transport modeling of GHGs, to serve as input for inverse modeling, and to reduce the impact of transport uncertainties. IAGOS-ERI (In-service Aircraft for a Global Observing System - European Research Infrastructure) exploits the synergy between globally operating civil aviation and the need for long-term monitoring of atmospheric composition. Within the framework of IAGOS-ERI a cavity ring-down spectroscopy (CRDS) based measurement system for greenhouse gases was designed, tested, and qualified for deployment on commercial airliners. The design meets requirements regarding physical dimensions (size, weight), performance (long-term stability, low maintenance, robustness, full automation) and safety issues (fire prevention regulations, airworthiness). The system uses components of a commercially available CRDS instrument (G2401-m, Picarro Inc.) mounted into a frame suitable for integration in the avionics bay of the Airbus A-340. The first of the IAGOS GHG packages is scheduled for integration in mid 2013. The aim is to have seven systems operational within four years, providing for long-term GHG observations with near-global coverage. To enable robust and automated operation of the IAGOS GHG package over six-month deployment periods, numerous technical issues had to be addressed. An inlet system, designed as virtual impactor to eliminate sampling of larger aerosols, ice particles, and water droplets, provides additional positive ram-pressure to ensure operation without an upstream sampling pump. Furthermore, no sample drying is required, as the simultaneously measured water vapor mole fraction is used to correct for dilution and spectroscopic effects. This also enables the collection of science-quality water vapor measurements throughout the atmosphere. To allow for trace gas measurements to be fully traceable to WMO scales, a two-standard calibration system has been designed and tested that periodically provides calibration gas to the instrument during flight and on ground for each six-month deployment period. We present results from recent test flights and laboratory tests that document the performance for GHG and water vapor measurements. Furthermore, future applications of the IAGOS-GHG data stream, provided in near-real-time via SatCom to the weather prediction centres, will be discussed.

  14. Study of acid-base properties in various water-salt and water-organic solvent mixtures; Etude de proprietes acides-bases dans divers melanges eau-sels et eau-solvants organiques

    Energy Technology Data Exchange (ETDEWEB)

    Lucas, M [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-02-01

    Acid-base reactions have been studied in water-salt mixtures and water organic solvent-mixtures. It has been possible to find some relations between the displacement of the equilibria and the numerical value of water activity in the mixture. First have been studied some equilibria H{sup +} + B {r_reversible} HB{sup +} in salt-water mixtures and found a relation between the pK{sub A} value, the solubility of the base and water activity. The reaction HO{sup -} + H{sup +} {r_reversible} H{sub 2}O has been investigated and a relation been found between pK{sub i} values, water activity and the molar concentration of the salt in the mixture. This relation is the same for every mixture. Then the same reactions have been studied in organic solvent-water mixtures and a relation found in the first part of the work have been used with success. So it has been possible to explain easily some properties of organic water-mixture as the shape of the curves of the Hammett acidity function Ho. (authors) [French] Nous avons envisage l'etude des reactions acides-bases dans des melanges eau-sels MX et des melanges d'eau et de solvants organiques. Les uns et les autres ont ete choisis de facon a ce que la basicite du solvant ou celle de l'anion X{sup -} soit negligeable devant celle de l'eau dans les melanges consideres. Dans un premier temps nous avons etudie dans les melanges eau-sels MX les equilibres H{sup +} + B {r_reversible} HB{sup +} et HA {r_reversible} H{sup +} + A{sup -}. On montre que connaissant la valeur de la solubilite de la base B et de l'acide HA dans le melange eau-sel considere et dans l'eau pure et celle de l'activite de l'eau dans le melange, il est possible de prevoir la valeur de la constante de l'equilibre acide-base etudiee. Dans un deuxieme temps nous avons cherche a generaliser ces resultats, lorsque l'on remplace le sel MX dans le melange avec l'eau par un solvant organique. De meme que precedemment, nous avons compare les constantes d'equilibre du type HB

  15. Quantitative measurements of small isotopic samples in gaseous mixtures by utilization of some nuclear properties; Etude des possibilites de mesures de faibles quantites de gaz radioactifs dans un melange en utilisant simultanement plusieurs proprietes nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Maragnon, J; Delperie, C

    1967-12-01

    The question is to define the characteristics of a group of measurements allowing the analysis of traces of radioactive rare gases in gas mixtures of different composition. To distinguish the radioactive isotopes from each other and the activity level reaching 10{sup 6} due to their nuclear properties, the method was chosen to use several nuclear properties: gamma radiation energy, beta particle energy, lifetime of excited states. The choice of a plastic scintillator as beta detector allows to answer satisfactorilly to this demand by measurement of nuclear constants because of the short de/excitation time of this detector. Another advantage is that it can be a reservoir for the sample without any destruction nor modification of the sample. The study has been based on the mixture of Kr-85, the analysis of other rare gases follwos immediately from the adopted principle. [French] Les auteurs ont oriente leur recherche vers une solution permettant de distinguer les isotopes radioactifs les uns des autres et dans des rapports d'activite pouvant atteindre 10{sup 6}, grace a plusieurs de leurs proprietes nucleaires, energie de rayonnement gamma, energie de la particule beta, temps de vie des niveaux excites. Le choix d'un scintillateur plastique comme detecteur beta permet de repondre d'une maniere satisfaisante a la mesure des constantes nucleaires en raison du temps de de/excitation rapide de ce scintillateur. Il offre en outre l'avantage de pouvoir servir de reservoir a l'echantillon sans entrainer aucune destruction ni modification de celui-ci. L'etude a ete basee sur la mixture de Kr-85, l'analyse des autre gaz rares decoulant immediatement du principe adopte. (auteur)

  16. Folds and Etudes

    Science.gov (United States)

    Bean, Robert

    2007-01-01

    In this article, the author talks about "Folds" and "Etudes" which are images derived from anonymous typing exercises that he found in a used copy of "Touch Typing Made Simple". "Etudes" refers to the musical tradition of studies for a solo instrument, which is a typewriter. Typing exercises are repetitive attempts to type words and phrases…

  17. Experiments on neutron-attenuation by water-lead mixtures; Etude experimentale de l'attenuation des neutrons dans les melanges plomb-eau

    Energy Technology Data Exchange (ETDEWEB)

    Beauge, R; Millot, J P; Rastoin, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    The penetration of fission neutrons in water-lead mixtures has been investigated in the NAIADE facility. The slopes of the thermal and fast fluxes (the latter measured with a dosimeter) remain similar when the volume proportion of water is greater than 65 per cent. For smaller water contents, the measurements show the evidence of streaming presumably due to slowing-down neutrons of energy smaller than 300 keV. (author) [French] La propagation des neutrons de fission a ete etudiee dans les melanges plomb-eau au moyen du dispositif NAIADE. La pente du flux thermique et la pente du flux rapide (obtenue au moyen d'un dosimetre) restent voisines lorsque la proportion d'eau dans le melange depasse 65 pour cent en volume. Pour des proportions inferieures les mesures mettent en evidence un 'streaming' de neutrons en ralentissement d'energie probablement inferieure a 300 keV. (auteur)

  18. Study of the rheological behaviour of corium/concrete mixtures; Etude du comportement rheologique de melanges issus de l'interaction corium/beton

    Energy Technology Data Exchange (ETDEWEB)

    Ramacciotti, M

    1999-09-24

    In the hypothetical event of a severe accident in a Light Water Reactor, scenarios in which the reactor pressure vessel (RPV) fails and the core melt mixture (called corium) relocates into the reactor cavity, cannot be excluded. The viscosity (in fact, corium rheological behaviour) plays a major role in many phenomena such as core melt down, discharge from reactor pressure vessel, interaction with structural materials (concrete,...) and spreading in a core-catcher. For these reasons, it is important to be able to predict the rheological behaviour of corium melts of different compositions (essentially based on UO{sub 2}, ZrO{sub 2}, Fe{sub x}O{sub y} and Fe for in-vessel scenarios, plus SiO{sub 2} and CaO for ex-vessel scenarios) at temperatures above solidus temperature. In the case of corium-concrete mixtures, the increase of viscosity depends not only on the increase of particles in the melts but also on the increase of the residual liquid phase viscosity (due to the increase in silica contents). The Urban correlation is used to calculate the viscosity of the carrying liquid with silica. This model was tested and gave good agreements between measured and estimated viscosities of various basalts among which one contained 18 wt% of UO{sub 2}. Then, in the solidification range, the analysis of published data showed that the viscosity cannot be described by a suspension viscosity model of non-interactive spherical particles; consequently we proposed an Arrhenius type law with a multiplying factor such as {eta}{sub r} = exp(2.5 C{phi}) and the C factor value varies between 4 and 8. This factor is more important in the case of low shear rates and low cooling rates. The analysis of the samples structure after quenching shows a dependence of this factor on the particle morphology. Finally, for a value of 6.1 of the C factor, we obtained the best agreement with experimental data for a corium spreading test at 2100 K on a horizontal surface. (author)

  19. Ideal gas solubilities and solubility selectivities in a binary mixture of room-temperature ionic liquids.

    Science.gov (United States)

    Finotello, Alexia; Bara, Jason E; Narayan, Suguna; Camper, Dean; Noble, Richard D

    2008-02-28

    This study focuses on the solubility behaviors of CO2, CH4, and N2 gases in binary mixtures of imidazolium-based room-temperature ionic liquids (RTILs) using 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][Tf2N]) and 1-ethyl-3-methylimidazolium tetrafluoroborate ([C2mim][BF4]) at 40 degrees C and low pressures (approximately 1 atm). The mixtures tested were 0, 25, 50, 75, 90, 95, and 100 mol % [C2mim][BF4] in [C2mim][Tf2N]. Results show that regular solution theory (RST) can be used to describe the gas solubility and selectivity behaviors in RTIL mixtures using an average mixture solubility parameter or an average measured mixture molar volume. Interestingly, the solubility selectivity, defined as the ratio of gas mole fractions in the RTIL mixture, of CO2 with N2 or CH4 in pure [C2mim][BF4] can be enhanced by adding 5 mol % [C2mim][Tf2N].

  20. Density functional theory for adsorption of gas mixtures in metal-organic frameworks.

    Science.gov (United States)

    Liu, Yu; Liu, Honglai; Hu, Ying; Jiang, Jianwen

    2010-03-04

    In this work, a recently developed density functional theory in three-dimensional space was extended to the adsorption of gas mixtures. Weighted density approximations to the excess free energy with different weighting functions were adopted for both repulsive and attractive contributions. An equation of state for hard-sphere mixtures and a modified Benedict-Webb-Rubin equation for Lennard-Jones mixtures were used to estimate the excess free energy of a uniform fluid. The theory was applied to the adsorption of CO(2)/CH(4) and CO(2)/N(2) mixtures in two metal-organic frameworks: ZIF-8 and Zn(2)(BDC)(2)(ted). To validate the theoretical predictions, grand canonical Monte Carlo simulations were also conducted. The predicted adsorption and selectivity from DFT were found to agree well with the simulation results. CO(2) has stronger adsorption than CH(4) and N(2), particularly in Zn(2)(BDC)(2)(ted). The selectivity of CO(2) over CH(4) or N(2) increases with increasing pressure as attributed to the cooperative interactions of adsorbed CO(2) molecules. The composition of the gas mixture exhibits a significant effect on adsorption but not on selectivity.

  1. Modeling Plasma-based CO2 and CH4 Conversion in Mixtures with N2, O2 and H2O: the Bigger Plasma Chemistry Picture

    KAUST Repository

    Wang, Weizong

    2018-01-18

    Due to the unique properties of plasma technology, its use in gas conversion applications is gaining significant interest around the globe. Plasma-based CO2 and CH4 conversion have become major research areas. Many investigations have already been performed regarding the single component gases, i.e. CO2 splitting and CH4 reforming, as well as for two component mixtures, i.e. dry reforming of methane (CO2/CH4), partial oxidation of methane (CH4/O2), artificial photosynthesis (CO2/H2O), CO2 hydrogenation (CO2/H2), and even first steps towards the influence of N2 impurities have been taken, i.e. CO2/N2 and CH4/N2. In this feature article we briefly discuss the advances made in literature for these different steps from a plasma chemistry modeling point of view. Subsequently, we present a comprehensive plasma chemistry set, combining the knowledge gathered in this field so far, and supported with extensive experimental data. This set can be used for chemical kinetics plasma modeling for all possible combinations of CO2, CH4, N2, O2 and H2O, to investigate the bigger picture of the underlying plasmachemical pathways for these mixtures in a dielectric barrier discharge plasma. This is extremely valuable for the optimization of existing plasma-based CO2 conversion and CH4 reforming processes, as well as for investigating the influence of N2, O2 and H2O on these processes, and even to support plasma-based multi-reforming processes.

  2. Effective ionization coefficients, electron drift velocities, and limiting breakdown fields for gas mixtures of possible interest to particle detectors

    International Nuclear Information System (INIS)

    Datskos, P.G.

    1991-01-01

    We have measured the gas-density, N, normalized effective ionization coefficient, bar a/N, and the electron drift velocity, w, as a function of the density-reduced electric field, E/N, and obtained the limiting, (E/N) lim , value of E/N for the unitary gases Ar, CO 2 , and CF 4 , the binary gas mixtures CO 2 :Ar (20: 80), CO 2 :CH 4 (20:80), and CF 4 :Ar (20:80), and the ternary gas mixtures CO 2 :CF 4 :Ar (10:10:80) and H 2 O: CF 4 :Ar (2:18:80). Addition of the strongly electron thermalizing gas CO 2 or H 2 O to the binary mixture CF 4 :Ar (1)''cools'' the mixture (i.e., lowers the electron energies), (2) has only a small effect on the magnitude of w(E/N) in the E/N range employed in the particle detectors, and (3) increases bar a/N for E/N ≥ 50 x 10 -17 V cm 2 . The increase in bar a/N, even though the electron energies are lower in the ternary mixture, is due to the Penning ionization of CO 2 (or H 2 O) in collisions with excited Ar* atoms. The ternary mixtures -- being fast, cool, and efficient -- have potential for advanced gas-filled particle detectors such as those for the SCC muon chambers. 17 refs., 8 figs., 1 tab

  3. CO2/CH4 Separation Performance of Ionic-Liquid-Based Epoxy-Amine Ion Gel Membranes under Mixed Feed Conditions Relevant to Biogas Processing.

    Czech Academy of Sciences Publication Activity Database

    Friess, K.; Lanč, M.; Pilnáček, Kryštof; Fíla, V.; Vopička, O.; Sedláková, Zuzana; Cowan, M.G.; McDaniel, W.M.; Noble, R.D.; Gin, D.L.; Izák, Pavel

    2017-01-01

    Roč. 528, APRIL (2017), s. 64-71 ISSN 0376-7388 R&D Projects: GA ČR GA14-12695S; GA MŠk LH14006; GA TA ČR TE01020080 Institutional support: RVO:67985858 Keywords : epoxy-amine-based ion gel membranes * biogas processing * humid mixed-gas permeation Subject RIV: CI - Industrial Chemistry, Chemical Engineering OBOR OECD: Chemical process engineering Impact factor: 6.035, year: 2016

  4. Effect of drainage on CO2, CH4, and N2O fluxes from aquaculture ponds during winter in a subtropical estuary of China.

    Science.gov (United States)

    Yang, Ping; Lai, Derrick Y F; Huang, Jia F; Tong, Chuan

    2018-03-01

    Aquaculture ponds are dominant features of the landscape in the coastal zone of China. Generally, aquaculture ponds are drained during the non-culture period in winter. However, the effects of such drainage on the production and flux of greenhouse gases (GHGs) from aquaculture ponds are largely unknown. In the present study, field-based research was performed to compare the GHG fluxes between one drained pond (DP, with a water depth of 0.05m) and one undrained pond (UDP, with a water depth of 1.16m) during one winter in the Min River estuary of southeast China. Over the entire study period, the mean CO 2 flux in the DP was (0.75±0.12) mmol/(m 2 ·hr), which was significantly higher than that in the UDP of (-0.49±0.09) mmol/(m 2 ·hr) (paquaculture ponds from a net sink to a net source of CO 2 in winter. Mean CH 4 and N 2 O emissions were significantly higher in the DP compared to those in the UDP (CH 4 =(0.66±0.31) vs. (0.07±0.06) mmol/(m 2 ·hr) and N 2 O=(19.54±2.08) vs. (0.01±0.04) µmol/(m 2 ·hr)) (paquaculture ponds can increase the emissions of potent GHGs from the coastal zone of China to the atmosphere during winter, further aggravating the problem of global warming. Copyright © 2017. Published by Elsevier B.V.

  5. Porous carbon derived via KOH activation of a hypercrosslinked porous organic polymer for efficient CO_2, CH_4, H_2 adsorptions and high CO_2/N_2 selectivity

    International Nuclear Information System (INIS)

    Modak, Arindam; Bhaumik, Asim

    2015-01-01

    Microporous carbon having Brunauer-Emmett-Teller (BET) surface area of 2186 m"2 g"−"1 and micropore volume of 0.85 cm"3 g"−"1 has been synthesized via KOH induced high temperature carbonization of a non-conjugated hypercrosslinked organic polymer. Owing to the templating and activation by KOH, we have succeeded in making a microporous carbon from this porous polymer and the resultant carbon material showed high uptake for CO_2 (7.6 mmol g"−"1) and CH_4 (2.4 mmol g"−"1) at 1 atm, 273 K together with very good selectivity for the CO_2/N_2 (30.2) separation. Furthermore, low pressure (1 atm) H_2 (2.6 wt%, 77 K) and water uptake (57.4 wt%, 298 K) ability of this polymer derived porous activated carbon is noteworthy. - Graphical abstract: Microporous carbon with BET surface area of 2186 m"2 g"−"1 has been synthesized via KOH activation of a porous organic polymer and it showed high uptake for CO_2 (7.6 mmol g"−"1), CH_4 (2.4 mmol g"−"1) and H_2 (2.6 wt%) at 1 atm together with very good selectivity for CO_2. - Highlights: • Porous carbon from hypercrosslinked organic polymer. • KOH activated carbon with BET surface area 2186 m"2 g"−"1. • High CO2 uptake (7.6 mmol g"−"1) and CO_2/N_2 selectivity (30.2). • Porous carbon also showed high H_2 (2.6 wt%) and H_2O (57.4 wt%) uptakes.

  6. Historical contribution by country of three greenhouse gases (CO2, CH4, N2O) to the climate change and Equity principle

    International Nuclear Information System (INIS)

    Muylaert, M.S.; De Campos, C.P.; Pinguelli Rosa, L.

    2003-11-01

    The historical contribution by country to climate change can be used as a basis of analysis for a second period of commitments to the burden share. The historical greenhouse gases emission inventory is an important tool to evaluate the common but differentiated responsibilities of groups according to the principle of the UN Framework Convention on Climate Convention (1992). This paper aims to discuss the differences among the meaning of the GHG historical emissions in terms of development patterns and suggests that different weights for different sectors should be taken into account. GHG emissions due to enteric fermentation from domestic livestock, for example, are linked to different regional activities such as food production, cultural expression or even religion meaning, depending on the region analyzed. Emissions due to fossil fuel sector represent in the majority a not feasible consumption pattern in terms of sustainable development

  7. Comprehensive laboratory and field testing of cavity ring-down spectroscopy analyzers measuring H2O, CO2, CH4 and CO

    Science.gov (United States)

    Yver Kwok, C.; Laurent, O.; Guemri, A.; Philippon, C.; Wastine, B.; Rella, C. W.; Vuillemin, C.; Truong, F.; Delmotte, M.; Kazan, V.; Darding, M.; Lebègue, B.; Kaiser, C.; Xueref-Rémy, I.; Ramonet, M.

    2015-09-01

    To develop an accurate measurement network of greenhouse gases, instruments in the field need to be stable and precise and thus require infrequent calibrations and a low consumption of consumables. For about 10 years, cavity ring-down spectroscopy (CRDS) analyzers have been available that meet these stringent requirements for precision and stability. Here, we present the results of tests of CRDS instruments in the laboratory (47 instruments) and in the field (15 instruments). The precision and stability of the measurements are studied. We demonstrate that, thanks to rigorous testing, newer models generally perform better than older models, especially in terms of reproducibility between instruments. In the field, we see the importance of individual diagnostics during the installation phase, and we show the value of calibration and target gases that assess the quality of the data. Finally, we formulate recommendations for use of these analyzers in the field.

  8. Comprehensive laboratory and field testing of cavity ring-down spectroscopy analyzers measuring H2O, CO2, CH4 and CO

    Directory of Open Access Journals (Sweden)

    C. Yver Kwok

    2015-09-01

    Full Text Available To develop an accurate measurement network of greenhouse gases, instruments in the field need to be stable and precise and thus require infrequent calibrations and a low consumption of consumables. For about 10 years, cavity ring-down spectroscopy (CRDS analyzers have been available that meet these stringent requirements for precision and stability. Here, we present the results of tests of CRDS instruments in the laboratory (47 instruments and in the field (15 instruments. The precision and stability of the measurements are studied. We demonstrate that, thanks to rigorous testing, newer models generally perform better than older models, especially in terms of reproducibility between instruments. In the field, we see the importance of individual diagnostics during the installation phase, and we show the value of calibration and target gases that assess the quality of the data. Finally, we formulate recommendations for use of these analyzers in the field.

  9. Post-synthetic modification of porphyrin-encapsulating metal-organic materials by cooperative addition of inorganic salts to enhance CO 2/CH 4 selectivity

    KAUST Repository

    Zhang, ZhenJie

    2012-08-21

    Keeping MOM: Reaction of biphenyl-3,4\\',5-tricarboxylate and Cd(NO 3) 2 in the presence of meso-tetra(N-methyl-4-pyridyl) porphine tetratosylate afforded porph@MOM-11, a microporous metal-organic material (MOM) that encapsulates cationic porphyrins and solvent in alternating open channels. Porph@MOM-11 has cation and anion binding sites that facilitate cooperative addition of inorganic salts (such as M +Cl -) in a stoichiometric fashion. © 2012 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. On the optimisation of trace gas measurements : A new method for in situ measurements of CO2, CH4, CO, SF6 and N2O

    NARCIS (Netherlands)

    Laan van der, Sander

    2005-01-01

    The release of anthropogenic greenhouse gases into the earth’s atmosphere is by far the largest uncontrolled experiment in the history of the earth. Mankind is drastically modifying the composition of the atmosphere, both in greenhouse gases and aerosols

  11. The IAGOS-core greenhouse gas package : a measurement system for continuous airborne observations of CO2, CH4, H2O and CO

    NARCIS (Netherlands)

    Filges, Annette; Gerbig, Christoph; Chen, Huilin; Franke, Harald; Klaus, Christoph; Jordan, Armin

    2015-01-01

    Within the framework of IAGOS-ERI (In-service Aircraft for a Global Observing System - European Research Infrastructure), a cavity ring-down spectroscopy (CRDS)-based measurement system for the autonomous measurement of the greenhouse gases (GHGs) CO2 and CH4, as well as CO and water vapour was

  12. Post-synthetic modification of porphyrin-encapsulating metal-organic materials by cooperative addition of inorganic salts to enhance CO 2/CH 4 selectivity

    KAUST Repository

    Zhang, ZhenJie; Gao, Wenyang; Wojtas, Łukasz; Ma, Shengqian; Eddaoudi, Mohamed; Zaworotko, Michael J.

    2012-01-01

    Keeping MOM: Reaction of biphenyl-3,4',5-tricarboxylate and Cd(NO 3) 2 in the presence of meso-tetra(N-methyl-4-pyridyl) porphine tetratosylate afforded porph@MOM-11, a microporous metal-organic material (MOM) that encapsulates cationic porphyrins and solvent in alternating open channels. Porph@MOM-11 has cation and anion binding sites that facilitate cooperative addition of inorganic salts (such as M +Cl -) in a stoichiometric fashion. © 2012 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. Influence of fertilizer placement on gaseous loss (CO2, CH4, N2O, and NH4) under different tillage management practices in a corn cropping system

    Science.gov (United States)

    Tillage and fertilizer application methods could alter plant yield and quality of corn production. Thus, a field experiment was conducted at the Sand Mountain Research Station located in the Appalachian Plateau region of Northeast Alabama on a Hartsells fine sandy loam to evaluate tillage (conventi...

  14. Ground-based DIAL and IPDA Systems for Remote Sensing of CO2, CH4, and H2O near 1.6 µm

    Science.gov (United States)

    Wagner, G. A.; Plusquellic, D. F.

    2017-12-01

    Integrated path differential absorption (IPDA) and differential absorption LIDAR (DIAL) are well established methods to monitor atmospheric constituents. At NIST, IPDA and DIAL systems have been developed as standoff systems and their overall performance has been evaluated through intercomparisons including the traceability to point sensor measurements. The all-fiber IPDA system is based on a low-power (Armstrong, and A. V. Smith, "150-mJ 1550-nm KTA OPO with Good Beam Quality and High Efficiency," SPIE, 5337, 71-80 (2004). 3. K. O. Douglass, S. E. Maxwell, D. F. Plusquellic, J. T. Hodges, R. D. van Zee, D. V. Samarov, J. R. Whetstone, "Construction of a High Power OPO Laser System for Differential Absorption LIDAR," SPIE, 8159, 81590D (2011).

  15. The Design of The Monitoring Tools Of Clean Air Condition And Dangerous Gas CO, CO2 CH4 In Chemical Laboratory By Using Fuzzy Logic Based On Microcontroller

    Science.gov (United States)

    Widodo, Slamet; Miftakul, Amin M.; Sutrisman, Adi

    2018-02-01

    There are many phenomena that human are exposed to toxins from certain types such as of CO2, CO2 and CH4 gases. The device used to detect large amounts of CO, CO2, and CH4 gas in air in enclosed spaces using MQ 135 gas sensors of different types based on the three sensitivity of the Gas. The results of testing the use of sensors MQ 135 on the gas content of CO, CO2 and CH4 received by the sensor is still in the form of ppm based on the maximum ppm detection range of each sensor. Active sensor detects CO 120 ppm gas, CO2 1600 ppm and CH4 1ppm "standby 1" air condition with intermediate rotary fan. Active sensor detects CO 30 ppm gas, CO2 490 ppm and CH4 7 ppm "Standby 2" with low rotating fan output. Fuzzy rulebase logic for motor speed when gas detection sensor CO, CO2, and CH4 output controls the motion speed of the fan blower. Active sensors detect CO 15 ppm, CO2 320 ppm and CH4 45 ppm "Danger" air condition with high fan spin fan. At the gas level of CO 15 ppm, CO2 390 ppm and CH4 3 ppm detect "normal" AC sensor with fan output stop spinning.

  16. The IAGOS GHG package: a measurement system for continuous airborne observations of CO2, CH4, H2O and CO

    Science.gov (United States)

    Gerbig, C.; Filges, A.; Franke, H.; Klaus, C.; Chen, H.

    2012-12-01

    A cavity ring-down spectroscopy (CRDS) based measurement system for greenhouse gases was designed, tested, and qualified for deployment on commercial airliners within the IAGOS-ERI (In-service Aircraft for a Global Observing System - European Research Infrastructure) project. The design meets requirements regarding physical dimensions (size, weight), performance (long term stability, low maintenance, robustness, full automation) and safety issues (fire prevention regulations). The system uses components of a commercially available CRDS instrument (G2401-m, Picarro Inc.) integrated in a frame suitable for integration in the avionics bay of the Airbus A-340. The first of the IAGOS GHG packages is scheduled for integration in early 2013. The aim is to have seven systems operational within four years, providing for long-term GHG observations with near-global coverage. To enable robust and automated operation of the IAGOS GHG package over six-month deployment periods, numerous technical issues had to be addressed. An inlet system, designed as virtual impactor to eliminate sampling of larger aerosols, ice particles, and water droplets, and provides additional positive ram-pressure. In combination with a lowered sample flow of 0.1 slpm, this ensures a fully controlled sample pressure in the cavity of 140 torr throughout the aircraft altitude operating range up to 12.5 km without the need of an upstream sampling pump. Furthermore, no sample drying is required, as the simultaneously measured water vapor mole fraction is used to correct for dilution and spectroscopic effects. This also enables the collection of science-quality water vapor measurements throughout the atmosphere. To allow for trace gas measurements to be fully traceable to WMO scales, a two-standard calibration system has been designed and tested that periodically provides calibration gas to the instrument during flight and on ground. A targeted six-month deployment cycle followed by maintenance of the package ensures a safe operation. During maintenance, calibration gases are analysed and replenished, and a functional inspection, followed by replacement of depleted or damaged parts, will be undertaken. Spare instrumentation will be used to provide for year-round GHG measurements on board each aircraft. We present results from recent test flights and laboratory tests that document the performance for GHG and water vapor measurements. Furthermore, future applications of the IAGOS-GHG data stream, provided in near-real-time via SatCom to the weather prediction centres, will be discussed, including the improved estimation of GHG budgets at regional to continental scales, the assessment of vertical transport in atmospheric models through comparison with observed vertical tracer distributions, and the validation of remote sensing measurements of GHGs.

  17. High accuracy Primary Reference gas Mixtures for high-impact greenhouse gases

    Science.gov (United States)

    Nieuwenkamp, Gerard; Zalewska, Ewelina; Pearce-Hill, Ruth; Brewer, Paul; Resner, Kate; Mace, Tatiana; Tarhan, Tanil; Zellweger, Christophe; Mohn, Joachim

    2017-04-01

    Climate change, due to increased man-made emissions of greenhouse gases, poses one of the greatest risks to society worldwide. High-impact greenhouse gases (CO2, CH4 and N2O) and indirect drivers for global warming (e.g. CO) are measured by the global monitoring stations for greenhouse gases, operated and organized by the World Meteorological Organization (WMO). Reference gases for the calibration of analyzers have to meet very challenging low level of measurement uncertainty to comply with the Data Quality Objectives (DQOs) set by the WMO. Within the framework of the European Metrology Research Programme (EMRP), a project to improve the metrology for high-impact greenhouse gases was granted (HIGHGAS, June 2014-May 2017). As a result of the HIGHGAS project, primary reference gas mixtures in cylinders for ambient levels of CO2, CH4, N2O and CO in air have been prepared with unprecedented low uncertainties, typically 3-10 times lower than usually previously achieved by the NMIs. To accomplish these low uncertainties in the reference standards, a number of preparation and analysis steps have been studied and improved. The purity analysis of the parent gases had to be performed with lower detection limits than previously achievable. E.g., to achieve an uncertainty of 2•10-9 mol/mol (absolute) on the amount fraction for N2O, the detection limit for the N2O analysis in the parent gases has to be in the sub nmol/mol domain. Results of an OPO-CRDS analyzer set-up in the 5µm wavelength domain, with a 200•10-12 mol/mol detection limit for N2O, will be presented. The adsorption effects of greenhouse gas components at cylinder surfaces are critical, and have been studied for different cylinder passivation techniques. Results of a two-year stability study will be presented. The fit-for-purpose of the reference materials was studied for possible variation on isotopic composition between the reference material and the sample. Measurement results for a suit of CO2 in air

  18. Polyimide hollow fiber membranes for CO2 separation from wet gas mixtures

    Directory of Open Access Journals (Sweden)

    F. Falbo

    2014-12-01

    Full Text Available Matrimid®5218 hollow fiber membranes were prepared using the dry-wet spinning process. The transport properties were measured with pure gases (H2, CO2, N2, CH4 and O2 and with a mixture (30% CO2 and 70% N2 in dry and wet conditions at 25 ºC, 50 ºC, 60 ºC and 75 ºC and up to 600 kPa. Interesting values of single gas selectivity up to 60 ºC (between 31 and 28 for CO2/N2 and between 33 and 30 for CO2/CH4 in dry condition were obtained. The separation factor measured for the mixture was 20% lower compared to the single gas selectivity, in the whole temperature range analyzed. In saturation conditions the data showed that water influences the performance of the membranes, inducing a reduction of the permeance of all gases. Moreover, the presence of water caused a decrease of single gas selectivity and separation factor, although not so significant, highlighting the very high water resistance of hollow fiber membrane modules.

  19. Functionalized copolyimide membranes for the separation of gaseous and liquid mixtures

    Directory of Open Access Journals (Sweden)

    Nadine Schmeling

    2010-08-01

    Full Text Available Functionalized copolyimides continue to attract much attention as membrane materials because they can fulfill the demands for industrial applications. Thus not only good separation characteristics but also high temperature stability and chemical resistance are required. Furthermore, it is very important that membrane materials are resistant to plasticization since it has been shown that this phenomenon leads to a significant increase in permeability with a dramatic loss in selectivity. Plasticization effects occur with most polymer membranes at high CO2 concentrations and pressures, respectively. Plasticization effects are also observed with higher hydrocarbons such as propylene, propane, aromatics or sulfur containing aromatics. Unfortunately, these components are present in mixtures of high commercial relevance and can be separated economically by single membrane units or hybrid processes where conventional separation units are combined with membrane-based processes. In this paper the advantages of carboxy group containing 6FDA (4,4′-hexafluoroisopropylidene diphthalic anhydride -copolyimides are discussed based on the experimental results for non cross-linked, ionically and covalently cross-linked membrane materials with respect to the separation of olefins/paraffins, e.g. propylene/propane, aromatic/aliphatic separation e.g. benzene/cyclohexane as well as high pressure gas separations, e.g. CO2/CH4 mixtures. In addition, opportunities for implementing the membrane units in conventional separation processes are discussed.

  20. CO2 capture by gas hydrate crystallization: Application on the CO2-N2 mixture

    International Nuclear Information System (INIS)

    Bouchemoua, A.

    2012-01-01

    CO 2 capture and sequestration represent a major industrial and scientific challenge of this century. There are different methods of CO 2 separation and capture, such as solid adsorption, amines adsorption and cryogenic fractionation. Although these processes are well developed at industrial level, they are energy intensive. Hydrate formation method is a less energy intensive and has an interesting potential to separate carbon dioxide. Gas hydrates are Document crystalline compounds that consist of hydrogen bonded network of water molecules trapping a gas molecule. Gas hydrate formation is favored by high pressure and low temperature. This study was conducted as a part of the SECOHYA ANR Project. The objective is to study the thermodynamic and kinetic conditions of the process to capture CO 2 by gas hydrate crystallization. Firstly, we developed an experimental apparatus to carry out experiments to determine the thermodynamic and kinetic formation conditions of CO 2 -N 2 gas hydrate mixture in water as liquid phase. We showed that the operative pressure may be very important and the temperature very low. For the feasibility of the project, we used TBAB (Tetrabutylammonium Bromide) as thermodynamic additive in the liquid phase. The use of TBAB may reduce considerably the operative pressure. In the second part of this study, we presented a thermodynamic model, based on the van der Waals and Platteeuw model. This model allows the estimation of thermodynamic equilibrium conditions. Experimental equilibrium data of CO 2 -CH 4 and CO 2 -N 2 mixtures are presented and compared to theoretical results. (author)

  1. Redução da emissão de CO2, CH4 e H2S através da compostagem de dejetos suínos Reduction emissions of CO2, CH4 and H2S through composting of swine manure

    Directory of Open Access Journals (Sweden)

    Luana G. Sardá

    2010-09-01

    Full Text Available Em conjunto com o crescente desenvolvimento da tecnologia para a produção de suínos ocorreu uma forte exploração e degradação do ambiente, razão pela qual a atividade se transformou em fonte poluidora das regiões produtoras. Buscam-se, então, alternativas que minimizem o potencial poluidor do atual sistema de produção. O trabalho proposto foi comparar o perfil de emissão de dióxido de carbono (CO2, metano (CH4 e gás sulfídrico (H2S do manejo de dejetos suínos nas formas sólida (compostagem e líquida (esterqueira, e avaliar a eficiência do processo de compostagem através dos parâmetros físico-químicos. O ensaio foi implantado no campo experimental da EMBRAPA Suínos e Aves, localizada no município de Concórdia, SC. Contatou-se, na compostagem, uma redução de 7 vezes na emissão de CH4, com relação à esterqueira; a emissão de CO2 representou 78,5% do carbono total mineralizado. Considerando-se que a emissão de H2S foi expressiva apenas no manejo dos dejetos na forma líquida, pode-se afirmar que o manejo dos resíduos na forma sólida é uma alternativa para a redução dos impactos ambientais pela mitigação do efeito estufa e pela redução de odores.In conjunction with the development of technologies for the production of swine meat, a strong exploration and degradation of the environment occurred and the activity became a source of pollution in the producing regions. Therefore, there is a need for alternative technologies that minimize the pollutant potential of the current system of production. The proposed work was to analyze and to compare the emission of carbon dioxide (CO2, methane (CH4 and hydrogen sulfide (H2S between the management of swine manure in solid form (composting and liquid manure (deep pit, and assess the efficiency of the process of composting through the physical and chemical parameters. The test was implemented in the experimental field of Embrapa Suínos e Aves, located in Concordia (SC. The results have showed that composting reduces 7 times the CH4 emission comparing to deep pit, and emission of CO2 represented 78.5% of total mineralized carbon. Considering that the emission of H2S was significant only in the management of waste in liquid form, then management of waste in solid form can reduce the environmental impacts, which tends to be beneficial in terms of mitigation of greenhouse effect and may contribute to the reduction of odors.

  2. Improvement in methanol production by regulating the composition of synthetic gas mixture and raw biogas.

    Science.gov (United States)

    Patel, Sanjay K S; Mardina, Primata; Kim, Dongwook; Kim, Sang-Yong; Kalia, Vipin C; Kim, In-Won; Lee, Jung-Kul

    2016-10-01

    Raw biogas can be an alternative feedstock to pure methane (CH4) for methanol production. In this investigation, we evaluated the methanol production potential of Methylosinus sporium from raw biogas originated from an anaerobic digester. Furthermore, the roles of different gases in methanol production were investigated using synthetic gas mixtures of CH4, carbon dioxide (CO2), and hydrogen (H2). Maximum methanol production was 5.13, 4.35, 6.28, 7.16, 0.38, and 0.36mM from raw biogas, CH4:CO2, CH4:H2, CH4:CO2:H2, CO2, and CO2:H2, respectively. Supplementation of H2 into raw biogas increased methanol production up to 3.5-fold. Additionally, covalent immobilization of M. sporium on chitosan resulted in higher methanol production from raw biogas. This study provides a suitable approach to improve methanol production using low cost raw biogas as a feed containing high concentrations of H2S (0.13%). To our knowledge, this is the first report on methanol production from raw biogas, using immobilized cells of methanotrophs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  3. Synthesis and characterization of ZIF-69 membranes and separation for CO2/CO mixture

    KAUST Repository

    Liu, Yunyang

    2010-05-01

    Continuous and c-oriented ZIF-69 membranes were successfully synthesized on porous alpha-alumina substrates by an in situ solvothermal method. The membranes were characterized by XRD, SEM and single-gas permeation tests. The BET measurements on crystals taken from the same mother liquor that was used for membrane synthesis yield a Langmuir surface area of 1138 m(2)/g. The stability of the membrane towards heat and different solvents were studied. Single-gas permeation experiments through ZIF-69 membranes were carried out by a vacuum method at room temperature using H-2, CH4, CO, CO2 and SF6, respectively. The permeances were in the order of H-2 > CO2 > CH4 > CO > SF6. The separation of CO2/CO gas mixture was investigated by gas chromatograph (GC) and the permselectivity of CO2/CO was 3.5 +/- 0.1 with CO2 permeance of 3.6 +/- 0.3 x 10(-8) mol m(-2) s(-1) Pa-1 at room temperature. (C) 2010 Elsevier B.V. All rights reserved.

  4. Rheological behavior study of a clay-polymer mixture: effects of the polymer addition; Etude du comportement rheologique de melanges argiles - polymeres. Effets de l'ajout de polymeres

    Energy Technology Data Exchange (ETDEWEB)

    Benchabane, A

    2006-11-15

    The aim of the present work is to establish a bibliographical synthesis on the microstructure, the colloidal and rheological characterization of bentonite suspensions with and without polymer/surfactant addition; to lead to a rheological characterization of clay-additive mixtures and to understand the interaction between the clay particles and polymer/surfactants. Different experimental measurements: rheology, particle sizing, and x-ray diffraction were used to study the rheological character of the water-bentonite-anionic additive mixtures (CMC, SDS, xanthane) as well as the nature of the particle-particle interactions and particle-additive. The modeling part led to the adoption of Tiu and Boger's model to predict the thixotropy of the bentonite suspensions without additive. Thus, a new model is proposed with physical parameters for a better correlation of the rheological behavior of the various studied mixtures. (author)

  5. Rheological behavior study of a clay-polymer mixture: effects of the polymer addition; Etude du comportement rheologique de melanges argiles - polymeres. Effets de l'ajout de polymeres

    Energy Technology Data Exchange (ETDEWEB)

    Benchabane, A

    2006-11-15

    The aim of the present work is to establish a bibliographical synthesis on the microstructure, the colloidal and rheological characterization of bentonite suspensions with and without polymer/surfactant addition; to lead to a rheological characterization of clay-additive mixtures and to understand the interaction between the clay particles and polymer/surfactants. Different experimental measurements: rheology, particle sizing, and x-ray diffraction were used to study the rheological character of the water-bentonite-anionic additive mixtures (CMC, SDS, xanthane) as well as the nature of the particle-particle interactions and particle-additive. The modeling part led to the adoption of Tiu and Boger's model to predict the thixotropy of the bentonite suspensions without additive. Thus, a new model is proposed with physical parameters for a better correlation of the rheological behavior of the various studied mixtures. (author)

  6. Density and electrical conductivity of molten salts. Comparative study of binary mixtures of alkali nitrates with silver nitrate and with thallium nitrate; Densite et conductibilite de sels fondus. Etude comparative des melanges binaires nitrates alcalins-nitrate d'argent et nitrates alcalins-nitrate de thallium

    Energy Technology Data Exchange (ETDEWEB)

    Brillant, S [Commissariat a l' Energie Atomique Saclay (France). Centre d' Etudes Nucleaires

    1967-10-01

    The choice of methods and the number of measurements made enable us to give results on the density and electrical conductivity of molten binary mixtures, alkali nitrate and silver nitrate, and alkali nitrate and thallium nitrate, in the form of equations. The deviations from linearity of the volume and the molar conductivity are determined by calculating the corresponding excess values whose variations are analyzed as a function of the Tobolsky parameter. The absence of any relationship in the sign of the entropy and the excess volume is justified. It is shown that the silver and thallium nitrates, in contrast to the thermodynamic properties, behave as the alkali nitrates in so far as the excess conductivity is concerned. This result is confirmed by the study of changes in the activation enthalpy for the partial molar conductivity; this study also shows the particular behaviour of lithium nitrate. (author) [French] Le choix des methodes et le nombre de mesures effectuees nous permettent de donner les resultats de densite et de conductibilite electrique des melanges fondus binaires nitrate alcalin-nitrate d'argent et nitrate alcalin-nitrate de thallium sous forme d'equations. Les ecarts a la linearite des isothermes de volume et de conductibilite molaire sont precises en calculant les grandeurs d'exces correspondantes dont les variations sont analysees en fonction du parametre de Tobolsky. Nous justifions l'absence de relation de signe entre l'entropie et le volume d'exces. Nous montrons que les nitrates d'argent et de thallium, vis-a-vis de la conductibilite d'exces, contrairement aux proprietes thermodynamiques, se conduisent comme les nitrates alcalins. Ce resultat est confirme par l'etude des variations des enthalpies d'activation de conductibilite partielle molaire qui met d'autre part en evidence le comportement particulier du nitrate de lithium. (auteur)

  7. Numerical and experimental study of the mixture of engine jets in the wake vortices of an airline aircraft; Etude numerique et experimentale du melange des jets de moteur dans les tourbillons de sillage d'un avion de ligne

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, St.

    1999-07-01

    This study is a contribution to the understanding of the formation and duration of aircraft condensation trails. The development of a numerical code based on the direct resolution of the 3-D compressible Navier-Stokes equations has been done first. Then, an experiment has been carried out in a wind tunnel to analyze the problem of the mixture of heated jets in a wing wake. A first validation of the numerical method has been carried out from bibliographic results and measurements of the mixture evolution of an inert tracer contained in the engine jets during a flight test. In order to characterize the condensation inside the wake, the evolution of the local water vapor saturation ratio has been calculated. The influence of the Crow instability on the mixture of effluents in the high atmosphere is also shown. Finally, a comparison is made between the numerical simulation results and the experimental measurements obtained in this study. The numerical results have also permitted to characterize the low scale exchange mechanisms between a turbulent jet and a swirl flow. (J.S.)

  8. Further details concerning the radiolysis of a carbon tetrachloride-benzene mixture (1961); Complements a l'etude de la radiolyse du melange tetrachlorure de carbone-benzene (1961)

    Energy Technology Data Exchange (ETDEWEB)

    May, S [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Gislon-Leray, N [Faculte des Sciences de Paris, 75 (France)

    1961-07-01

    The neutron-activation estimation of the chlorine fixed on DPPH during radiolysis of the mixture C{sub 6}H{sub 6}-CCl{sub 4} makes it possible to evaluate the contribution of the carbon tetrachloride to the overall phenomenon. (authors) [French] Le dosage par activation neutronique du chlore fixe sur le DPPH lors de la radiolyse du melange C{sub 6}H{sub 6}-CCl{sub 4} permet d'evaluer la contribution du tetrachlorure de carbone au phenomene global. (auteurs)

  9. Phase behaviour in water/hydrocarbon mixtures involved in gas production systems; etude des equilibres des systemes: eau-hydrocarbures-gaz acides dans le cadre de la production de gaz

    Energy Technology Data Exchange (ETDEWEB)

    Chapoy, A.

    2004-11-15

    Inside wells, natural gases frequently coexist with water. The gases are in equilibrium with the sub-adjacent aquifer. Many problems are associated with the presence of water during the production, transport and processing of natural gases. Accurate knowledge of the thermodynamic properties of the water/hydrocarbon and water-inhibitor/hydrocarbon equilibria near the hydrate forming conditions, at sub-sea pipeline conditions and during the transport is crucial for the petroleum industry. An apparatus based on a static/analytic method combined with a dilutor apparatus to calibrate on the gas chromatograph (GC) detectors with water was used to measure the water content of binary systems (i.e.: water - methane, ethane - water, nitrogen - water...) as well of a synthetic hydrocarbon gas mixture (i.e.: 94% methane, 4% ethane and 2% n-butane) with and without inhibitor. This same apparatus was also used generate data of methane, ethane, propane, n-butane and nitrogen solubility in water and also the solubilities of a synthetic mixture in water. In-house software has been developed in order to fit and model the experimental data. (author)

  10. Molecular Dynamics Simulations of Carbon Dioxide, Methane, and Their Mixture in Montmorillonite Clay Hydrates

    KAUST Repository

    Kadoura, Ahmad Salim

    2016-05-26

    Molecular dynamics simulations were carried out to study the structural and transport properties of carbon dioxide, methane, and their mixture at 298.15 K in Na-montmorillonite clay in the presence of water. The simulations show that, the self-diffusion coefficients of pure CO2 and CH4 molecules in the interlayers of Na-montmorillonite decrease as their loading increases, possibly because of steric hindrance. The diffusion of CO2 in the interlayers of Na-montmorillonite, at constant loading of CO2, is not significantly affected by CH4 for the investigated CO2/CH4 mixture compositions. We attribute this to the preferential adsorption of CO2 over CH4 in Na-montmorillonite. While the presence of adsorbed CO2 molecules, at constant loading of CH4, very significantly reduces the self-diffusion coefficients of CH4, and relatively larger decrease in those diffusion coefficients are obtained at higher loadings. The preferential adsorption of CO2 molecules to the clay surface screens those possible attractive surface sites for CH4. The competition between screening and steric effects leads to a very slight decrease in the diffusion coefficients of CH4 molecules at low CO2 loadings. The steric hindrance effect, however, becomes much more significant at higher CO2 loadings and the diffusion coefficients of methane molecules significantly decrease. Our simulations also indicate that, similar effects of water on both carbon dioxide and methane, increase with increasing water concentration, at constant loadings of CO2 and CH4 in the interlayers of Na-montmorillonite. Our results could be useful, because of the significance of shale gas exploitation and carbon dioxide storage.

  11. Molecular Dynamics Simulations of Carbon Dioxide, Methane, and Their Mixture in Montmorillonite Clay Hydrates

    KAUST Repository

    Kadoura, Ahmad Salim; Nair, Arun Kumar Narayanan; Sun, Shuyu

    2016-01-01

    Molecular dynamics simulations were carried out to study the structural and transport properties of carbon dioxide, methane, and their mixture at 298.15 K in Na-montmorillonite clay in the presence of water. The simulations show that, the self-diffusion coefficients of pure CO2 and CH4 molecules in the interlayers of Na-montmorillonite decrease as their loading increases, possibly because of steric hindrance. The diffusion of CO2 in the interlayers of Na-montmorillonite, at constant loading of CO2, is not significantly affected by CH4 for the investigated CO2/CH4 mixture compositions. We attribute this to the preferential adsorption of CO2 over CH4 in Na-montmorillonite. While the presence of adsorbed CO2 molecules, at constant loading of CH4, very significantly reduces the self-diffusion coefficients of CH4, and relatively larger decrease in those diffusion coefficients are obtained at higher loadings. The preferential adsorption of CO2 molecules to the clay surface screens those possible attractive surface sites for CH4. The competition between screening and steric effects leads to a very slight decrease in the diffusion coefficients of CH4 molecules at low CO2 loadings. The steric hindrance effect, however, becomes much more significant at higher CO2 loadings and the diffusion coefficients of methane molecules significantly decrease. Our simulations also indicate that, similar effects of water on both carbon dioxide and methane, increase with increasing water concentration, at constant loadings of CO2 and CH4 in the interlayers of Na-montmorillonite. Our results could be useful, because of the significance of shale gas exploitation and carbon dioxide storage.

  12. Contribution to the study of thermal diffusion in isotopic mixtures of hydrogen; Contribution a l'etude de la diffusion thermique dans les melanges isotopiques de l'hydrogene

    Energy Technology Data Exchange (ETDEWEB)

    Lemarechal-Dupuis, A [Commissariat a l' Energie Atomique, 91 - Saclay (France). Centre d' Etudes Nucleaires

    1968-04-01

    Thermal diffusion constants of the mixtures H{sub 2}-HD and H{sub 2}-HT, where HD and HT were at trace concentrations, have been measured between 90 deg. K and 450 deg. K for H{sub 2}-HD and between 190 deg. K and 450 deg. K for H{sub 2}-HT, by using the elementary effect. Furthermore, the ratio of these constants has been measured by using a thermo-gravitational column of Clusius and Dickel, at temperatures of the hot wire between 455 deg. K and 1200 deg. K, the cold wall being at room temperature. Comparison with the predictions of existing theories shows that the Chapman-Enskog theory cannot account for the thermal diffusion of mixtures containing asymmetric molecules; the possible reasons for this disagreement are discussed. Our set of measurements, combined with the results of other authors, yields precise values at well defined conditions of temperature and concentration, useful for the determination of the coefficients of the semi-empirical expansion of Waldmann and Klemm. Furthermore some aspects of the column theory according to Furry and Jones have been tested. (author) [French] Les constantes de diffusion thermique des melanges H{sub 2}-HD et H{sub 2}-HT ou HD et HT figuraient, a l'etat de traces, ont ete mesurees a l'aide de l'effet elementaire entre 90 deg. K et 450 deg. K pour le melange H{sub 2}-HD,et entre 190 deg. K et 450 deg. K pour le melange H{sub 2}-HT. D'autre part, le rapport de ces constantes a ete mesure a l'aide d'une colonne de Clusius et Dickel pour des temperatures du fil chaud variant entre 455 deg. K et 1200 deg. K, la temperature de la paroi froide etant la temperature ambiante. La comparaison avec les predictions des theories existantes montre que la theorie de Chapman- Enskog ne peut rendre compte de la constante de diffusion thermique de melanges de molecules asymetriques; les raisons de ce desaccord sont discutees. L'ensemble de ces mesures, combine aux resultats d'autres auteurs, permet d'obtenir des valeurs precises dans des

  13. Utilization of acetone-butanol-ethanol-water mixture obtained from biomass fermentation as renewable feedstock for hydrogen production via steam reforming: Thermodynamic and energy analyses.

    Science.gov (United States)

    Kumar, Brajesh; Kumar, Shashi; Sinha, Shishir; Kumar, Surendra

    2018-08-01

    A thermodynamic equilibrium analysis on steam reforming process to utilize acetone-butanol-ethanol-water mixture obtained from biomass fermentation as biorenewable fuel has been performed to produce clean energy carrier H 2 via non-stoichiometric approach namely Gibbs free energy minimization method. The effect of process variables such as temperature (573-1473 K), pressure (1-10 atm), and steam/fuel molar feed ratio (F ABE  = 5.5-12) have been investigated on equilibrium compositions of products, H 2 , CO, CO 2 , CH 4 and solid carbon. The best suitable conditions for maximization of desired product H 2 , suppression of CH 4 , and inhibition of solid carbon are 973 K, 1 atm, steam/fuel molar feed ratio = 12. Under these conditions, the maximum molar production of hydrogen is 8.35 with negligible formation of carbon and methane. Furthermore, the energy requirement per mol of H 2 (48.96 kJ), thermal efficiency (69.13%), exergy efficiency (55.09%), exergy destruction (85.36 kJ/mol), and generated entropy (0.29 kJ/mol.K) have been achieved at same operating conditions. Copyright © 2018 Elsevier Ltd. All rights reserved.

  14. Experimental study of heat exchange coefficients, critical heat flux and charge losses, using water-steam mixtures in turbulent flow in a vertical tube; Etude experimentale des coefficients d'echanges thermiques, des flux de chaleur critiques et des pertes de charge avec des melanges eau-vapeur en ecoulement turbulent dans un tube vertical

    Energy Technology Data Exchange (ETDEWEB)

    Perroud, P; De La Harpe, A; Rebiere, J [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1960-12-15

    Two stainless steel tubes were used (with diameters of 5 and 10 mm, lengths 400 and 600 mm respectively), heated electrically (50 Hz). The mixture flows from top to bottom. The work was carried out mainly on mixtures of high concentration (x > 0.1), at pressures between 50 and 60 kg/cm{sup 2}, flowing as a liquid film on the walls of the tube with droplets suspended in the central current of steam. By analysis of the heat transfer laws the exchange mechanisms were established, and the conditions under which the critical heat flux may be exceeded without danger of actual burnout were determined. In this way high output concentrations (x{sub s} > 0.9) may be obtained. An attempt has been made to find out to what extent existing correlation formulae can be used to account for the phenomena observed. It is shown that those dealing with exchange coefficients can only be applied in a first approximation in cases where exchange by convection is preponderant, and only below the critical flux. The formulae proposed by WAPD and CISE do not give a satisfactory estimation of the critical heat flux, and the essential reasons for this inadequacy are explained. Lastly, the Martinelli and Nelson method may be used to an approximation of 30 per cent for the calculation of charge losses. (author) [French] On a utilise deux tubes en acier inox (avec des diametres de 5 et 10 mm, et des longueurs respectives 400 et 600 mm) chauffes electriquement (50 Hz). Le melange s'ecoule de haut en bas. Les etudes ont porte plus specialement sur des melanges de titres eleves (x > 0,1) a des pressions comprises entre 60 et 90 kg/cm{sup 2} dont l'ecoulement se fait avec film liquide annulaire et gouttelettes en suspension dans le coeur de vapeur. Par l'analyse des lois de transfert de chaleur, on a precise les mecanismes d'echanges et l'on a d'autre part determine dans quelles conditions le flux de chaleur critique peut etre depasse sans danger de 'burnout' proprement dit. On peut ainsi obtenir des

  15. Contribution to the study of the flow of adsorbed phases. Enrichment of binary Gaseous mixtures; Contribution a l'etude de l'ecoulement des phases absorbees. Enrichissement des melanges gazeux binaires

    Energy Technology Data Exchange (ETDEWEB)

    Sapet, J C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1962-12-15

    The research which makes up this thesis is concerned both with the problems of adsorption an chromatographic columns and of catalysis, which involve the surface properties of these solids, and with problems of isotope separation by gaseous diffusion. In this latter case, the flow in the two-dimensional adsorbed phase is a secondary phenomenon but it is nevertheless necessary to know its influence on the separation factor. Up to the present time very little work has been published on this subject, the importance of which needs no stressing. The author has devised very sensitive techniques making it possible to study the flow of two-dimensional phases in micro-porous bodies. He has demonstrated not only the role of the relative pressure and of the nature of the components (gas and solid) but also the relationship between the mobility of the adsorbate and the thermodynamic characteristics of the adsorption. The author has treated numerous examples involving the diffusion either of pure gases (n-butane, n-pentane, isopentane), or of binary mixtures, and has shown on the one hand that the separative effect of the two-dimensional flow at the interface is a maximum in the neighbourhood of the monolayer, and on the other hand that the mass effect is of the second order with respect to the structural factor of the diffusing molecule. The problem considered is of importance both from a fundamental point of view and from that of its industrial applications. (author) [French] Le sujet de travail de cette these interesse aussi bien les problemes d'adsorption sur colonne de chromatographie et de catalyse, qui font intervenir directement les proprietes superficielles des solides, que ceux concernant la separation isotopique par diffusion gazeuse. Dans ce dernier cas l'ecoulement en phase adsorbee bidimensiormelle est un phenomene secondaire dont i1 faut cependant connaitre l'effet sur le facteur de separation. Pratiquement aucun travail fondamental n'a encore ete publie sur ce

  16. Criticality studies; Etudes de criticite

    Energy Technology Data Exchange (ETDEWEB)

    Breton, D; Lecorche, P; Clouet d' Orval, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Criticality studies made at the Commissariat a l'Energie atomique deal on the one hand with experiments on plutonium and uranium solutions, on the other hand with theoretical work on the development and use of computation, methods for the resolution of problems concerning the nuclear safety of chemical and metallurgical plants. I - Since 1958 the experimental studies have dealt with homogeneous media constituted by a fissile salt dissolved in light water. Developed using the reactor Proserpine, the experiments have been carried on at Saclay on the Alecto assemblies where solutions of plutonium or of 90 p.100 - enriched uranium can be made critical. The results already obtained relate to critical masses of cylindrical tanks of diameters from 20 to 50 cm. reflected in several ways (water, concrete, etc. . ) at concentrations up to 100 g/liter. Physical measurements (spectra, reactor noises) and interaction measurements complete the results. Other experiments relating to plutonium solutions were begun in 1963, at the Valduc Center. They deal with the study of critical masses of annular vessels of external diameter 50 cm and internal diameter varying from 10 to 30 cm. These vessels can be water reflected internally, externally, or both. Two of these vessels have been studied in interaction for various geometries. Slabs of various thicknesses were also studied. II - The studies thus undertaken allowed the development of methods of computation which have been tested on several experiments. Particular use has been made of the possibilities of calculations based on transport theory and on Monte Carlo methods. All these theoretical studies are applied to the design and control of industrial plants from the point of view of safety. (authors) [French] Les etudes de criticite effectuees au CEA comportent d'une part des experiences sur des solutions de plutonium et d'uranium enrichi, d'autre part des travaux theoriques portant sur la mise au point et l'exploitation de methodes

  17. Seasonal changes of CO2, CH4 and N2O fluxes in relation to land-use change in tropical peatlands located in coastal area of South Kalimantan

    International Nuclear Information System (INIS)

    Inubushi, K.; Furukawa, Y.; Hadi, A.; Purnomo, E.; Tsuruta, H.

    2003-01-01

    Tropical peatland could be a source of greenhouse gases emission because it contains large amounts of soil carbon and nitrogen. However these emissions are strongly influenced by soil moisture conditions. Tropical climate is characterized typically by wet and dry seasons. Seasonal changes in the emission of carbon dioxide (CO 2 ), methane (CH 4 ) and nitrous oxide (N 2 O) were investigated over a year at three sites (secondary forest, paddy field and upland field) in the tropical peatland in South Kalimantan, Indonesia. The amount of these gases emitted from the fields varied widely according to the seasonal pattern of precipitation, especially methane emission rates were positively correlated with precipitation. Converting from secondary forest peatland to paddy field tended to increase annual emissions of CO 2 and CH 4 to the atmosphere (from 1.2 to 1.5 kg CO 2 -C m -2 y -1 and from 1.2 to 1.9 g CH 4 -C m -2 y -1 ), while changing land-use from secondary forest to upland tended to decrease these gases emissions (from 1.2 to 1.0 kg CO 2 -C m -2 y -1 and from 1.2 to 0.6 g CH 4 -C m -2 y -1 ), but no clear trend was observed for N 2 O which kept negative value as annual rates at three sites. (Author)

  18. Annual emissions of CO2, CH4 and N2O from a temperate peat bog: Comparison of an undrained and four drained sites under permanent grass and arable crop rotations with cereals and potato

    DEFF Research Database (Denmark)

    Kandel, Tanka; Lærke, Poul Erik; Elsgaard, Lars

    2018-01-01

    intervals using static chambers, and auxiliary data were obtained, such as temperature, depth of water table, ratio-vegetation index, pH and soil mineral N. Annual CO2 emissions were derived from empirical modelling, whereas CH4 and N2O emissions were linearly interpolated between measurement dates...

  19. Evaluation of the greenhouse effect gases (CO2, CH4, N2O) in grass land and in the grass breeding. Greenhouse effect gases prairies. report of the first part of the project December 2002

    International Nuclear Information System (INIS)

    Soussana, J.F.

    2002-12-01

    In the framework of the Kyoto protocol on the greenhouse effect gases reduction, many ecosystems as the prairies can play a main role for the carbon sequestration in soils. The conservation of french prairies and their management adaptation could allow the possibility of carbon sequestration in the soils but also could generate emissions of CO 2 and CH 4 (by the breeding animals on grass) and N 2 O (by the soils). This project aims to establish a detailed evaluation of the contribution of the french prairies to the the greenhouse effect gases flux and evaluate the possibilities of reduction of the emissions by adaptation of breeding systems. (A.L.B.)

  20. How well can we assess impacts of agricultural land management changes on the total greenhouse gas balance (CO2, CH4 and N2O) of tropical rice-cropping systems with biogeochemical models?

    Science.gov (United States)

    Kraus, David; Weller, Sebastian; Janz, Baldur; Klatt, Steffen; Santabárbara, Ignacio; Haas, Edwin; Werner, Christian; Wassmann, Reiner; Kiese, Ralf; Butterbach-Bahl, Klaus

    2016-04-01

    Paddy rice cultivation is increasingly challenged by physical and economic irrigation water scarcity. This already results in the trend of converting paddy rice to upland crop cultivation (e.g., maize, aerobic rice) in large parts of South East Asia. Such land management change from flooded lowland systems to well-aerated upland systems drastically affects soil C and N cycling and related emissions of greenhouse gases. Emissions of methane (CH4) are expected to decrease, while emissions of nitrous oxide (N2O) will most likely increase. In addition to such fast evolving 'pollution swapping' it is expected that on longer time scales significant amounts of soil organic carbon (SOC) stocks will be lost in form of carbon dioxide (CO2). Within the DFG-funded research unit ICON (Introducing non-flooded crops in rice-dominated landscapes: Impact on carbon, nitrogen and water cycles), we investigated environmental impacts of land management change from historical paddy rice cultivation to the upland crops maize and aerobic rice at experimental sites at the International Rice Research Institute (IRRI), the Philippines. To present, more than three years of continuous measurement data of CH4 and N2O emissions under different fertilization regimes have been collected. In addition, measurements of SOC contents and bulk densities in different soil horizons allow for an overall very good characterization of the environmental impacts of mentioned land management change. In this contribution we will show how well mentioned land management change effects in tropical agricultural systems can be represented and thus better understood by the help of process-based biogeochemical models. Seasonal emissions of CH4 and N2O are simulated with r2 values of 0.85 and 0.78 and average underestimations of 15 and 14 %, respectively. These underestimations predominantly originate from treatments in which no fertilizer is applied (CH4) as well as uncertainties of soil hydrology (N2O). Long-term development of SOC stocks is highly influenced by the soil oxygen status as well as the growth of photosynthetic active aquatic biomass. Moreover, simulation results demonstrate that short-term GHG balances may considerably differ from long-term balances. Simulated total GHG emissions 2.5 years after land management change are highest for upland crop - paddy rice rotations due to pronounced losses of soil organic carbon. In contrast, over a longer period of several decades total GHG emissions are highest for double cropping of paddy rice clearly dominated by CH4 emissions. Simulation results suggest that approx. 2.8 - 3.4 t C ha-1 yr-1 residue incorporation after harvest is needed in order to sustain stable SOC stocks in mixed upland crop - paddy rice systems.

  1. "Atmospheric Measurements by Ultra-Light SpEctrometer" (AMULSE) dedicated to vertical profile measurements of greenhouse gases (CO2, CH4) under stratospheric balloons: instrumental development and field application.

    Science.gov (United States)

    Maamary, Rabih; Joly, Lilian; Decarpenterie, Thomas; Cousin, Julien; Dumelié, Nicolas; Grouiez, Bruno; Albora, Grégory; Chauvin, Nicolas; Miftah-El-Khair, Zineb; Legain, Dominique; Tzanos, Diane; Barrié, Joel; Moulin, Eric; Ramonet, Michel; Bréon, François-Marie; Durry, Georges

    2016-04-01

    Human activities disrupt natural biogeochemical cycles such as the carbon and contribute to an increase in the concentrations of the greenhouse gases (carbone dioxide and methane) in the atmosphere. The current atmospheric transport modeling (the vertical trade) still represents an important source of uncertainty in the determination of regional flows of greenhouse gases, which means that a good knowledge of the vertical distribution of CO2 is necessary to (1) make the link between the ground measurements and spatial measurements that consider an integrated concentration over the entire column of the atmosphere, (2) validate and if possible improve CO2 transport model to make the link between surface emissions and observed concentration. The aim of this work is to develop a lightweight instrument (based on mid-infrared laser spectrometry principles) for in-situ measuring at high temporal/spatial resolution (5 Hz) the vertical profiles of the CO2 and the CH4 using balloons (meteorological and BSO at high precision levels (costs and logistics flights. These laser spectrometers are built on recent instrumental developments. Several flights were successfully done in the region Champagne-Ardenne and in Canada recently. Aknowledgments: The authors acknowledge financial supports from CNES, CNRS défi instrumental and the region Champagne-Ardenne.

  2. High pressure pure- and mixed-gas separation of CO2/CH4 by thermally-rearranged and carbon molecular sieve membranes derived from a polyimide of intrinsic microporosity

    KAUST Repository

    Swaidan, Raja; Ma, Xiaohua; Litwiller, Eric; Pinnau, Ingo

    2013-01-01

    Natural gas sweetening, one of the most promising venues for the growth of the membrane gas separation industry, is dominated by polymeric materials with relatively low permeabilities and moderate selectivities. One strategy towards improving

  3. Gases for an SSC muon detector

    International Nuclear Information System (INIS)

    Christophorou, L.G.; Datskos, P.G.; Carter, J.G.; Tennessee Univ., Knoxville, TN

    1990-01-01

    Recent measurements of electron drift velocities as a function of the density-reduced electric field E/N are reported for a number of unitary gases and the mixtures CO 2 /CH 4 and NH 3 /CF 4 /Ar. Calculated values of the mean electron energy as a function of E/N are also reported for unitary gases and mixtures of CO 2 /CH 4 . 7 refs., 5 figs

  4. Quantitative Studies of the Reactions of Hot Tritium Atoms with Hydrocarbons and Hydrocarbon Mixtures; Etudes Quantitatives des Reactions des Atomes Chauds de Tritium avec les Hydrocarbures et les Melanges d'Hydrocarbures; Kolichestvennoe issledovanie reaktsij goryachikh atomov tritiya s gidrouglerodami i smesyami gidrouglerodov; Estudio Cuantitativo de las Reacciones de Atomos de Tritio Calientes con Hidrocarburos y Mezclas de Hidrocarburos

    Energy Technology Data Exchange (ETDEWEB)

    Urch, D. S.; Welch, M. J. [Department Of Chemistry, Queen Mary College. University of London, London (United Kingdom)

    1965-04-15

    The kinetic theory of hot-atom reactions is expanded to cover the general system of two reactive species and an inert moderator. From results with a single reactant and moderator, two reactants without moderator, and two reactants with moderator, values of, or ratios of, the reactivity integral I and the average logarithmic energy loss per collision a can be calculated. New results are presented from the reaction of hot tritium produced by the He{sup 3}(n, p)H{sup 3} reaction with the following systems (all contain oxygen scavenger): ethane with helium moderator butane with helium moderator neopentane with helium moderator ethane and butane with and without helium moderator ethane and neopentane with and without helium moderator Values of a and I for the three reactants are calculated from the three types of system and the agreement between the results is discussed in the terms of the accuracy of the model. The results obtained from the different systems agree to within the limits of the experimental error, and this shows that the kinetic theory model can be applied to hot-atom systems with some certainty and that the assumptions made when considering mixtures are reasonable ones. The ratios of the reactivity of the hydrocarbons in mixtures with regard to substitution reactions are not the same as the ratios of the number of hydrogen atoms in the hydrocarbons. The values obtained for these ratios are explained in terms of the values of I and S (the collision cross-section) for the hydrocarbons. (author) [French] Les auteurs etendent la theorie cinetique des reactions des atomes chauds au systeme general forme par deux especes reactives et un ralentisseur inerte. A partir des resultats obtenus au moyen d'un seul corps en reaction et d'un ralentisseur, de deux corps en reaction sans ralentisseur et de deux corps en reaction avec ralentisseur, il est possible de calculer les valeurs ou les rapports de l'integrale de reactivite I, et de la perte d'energie logarithmique

  5. ETUDE - European Trade Union Distance Education.

    Science.gov (United States)

    Creanor, Linda; Walker, Steve

    2000-01-01

    Describes transnational distance learning activities among European trade union educators carried out as part of the European Trade Union Distance Education (ETUDE) project, supported by the European Commission. Highlights include the context of international trade union distance education; tutor training course; tutors' experiences; and…

  6. Synthesis, Characterization, and Impregnation of Some Ionic Liquids on Polymer Membrane for Separation of Carbon Dioxide from Its Mixture with Methane

    Directory of Open Access Journals (Sweden)

    T. T. L. Bui

    2018-03-01

    Full Text Available Some 1-alkyl-3-methylimidazolium-based ionic liquids were synthesized, characterized, and immobilized on membranes to form supported ionic liquid membranes. The supported ionic liquid membranes were characterized by SEM. The initial transmembrane pressures were investigated for each type of impregnated membrane. The CO2/CH4 single gas and mixed gas permeability (CO2 and CH4 have been investigated. The results showed that the CO2/CH4 ideal selectivities and mixed gas selectivities reached 15.45 – 23.9 and 13.91 – 22.82, respectively (equivalent to separation yields of 93.3 – 95.98 %.mThe 1-alkyl-3-methylimidazolium acetate impregnated membrane leads to a slightly lowermCO2/CH4 selectivity, however, this ionic liquid is stable, free of halogen and has a low price. The impregnated membranes prepared from polyvinylidene fluoride are more stablemthan those from polyethersulfone support, and have a higher affinity for CO2 compared to other gas. The obtained high CO2/CH4 selectivities indicate that immobilized membranes can be used for CO2 separation processes.

  7. Measurement and modelling of high pressure density and interfacial tension of (gas + n-alkane) binary mixtures

    International Nuclear Information System (INIS)

    Pereira, Luís M.C.; Chapoy, Antonin; Burgass, Rod; Tohidi, Bahman

    2016-01-01

    Highlights: • (Density + IFT) measurements are performed in synthetic reservoir fluids. • Measured systems include CO_2, CH_4 and N_2 with n-decane. • Novel data are reported for temperatures up to 443 K and pressures up to 69 MPa. • Predictive models are tested in 16 (gas + n-alkane) systems. • Best modelling results are achieved with the Density Gradient Theory. - Abstract: The deployment of more efficient and economical extraction methods and processing facilities of oil and gas requires the accurate knowledge of the interfacial tension (IFT) of fluid phases in contact. In this work, the capillary constant a of binary mixtures containing n-decane and common gases such as carbon dioxide, methane and nitrogen was measured. Experimental measurements were carried at four temperatures (313, 343, 393 and 442 K) and pressures up to 69 MPa, or near the complete vaporisation of the organic phase into the gas-rich phase. To determine accurate IFT values, the capillary constants were combined with saturated phase density data measured with an Anton Paar densitometer and correlated with a model based on the Peng–Robinson 1978 equation of state (PR78 EoS). Correlated density showed an overall percentage absolute deviation (%AAD) to measured data of (0.2 to 0.5)% for the liquid phase and (1.5 to 2.5)% for the vapour phase of the studied systems and P–T conditions. The predictive capability of models to accurately describe both the temperature and pressure dependence of the saturated phase density and IFT of 16 (gas + n-alkane) binary mixtures was assessed in this work by comparison with data gathered from the literature and measured in this work. The IFT models considered include the Parachor, the Linear Gradient Theory (LGT) and the Density Gradient Theory (DGT) approaches combined with the Volume-Translated Predictive Peng–Robinson 1978 EoS (VT-PPR78 EoS). With no adjustable parameters, the VT-PPR78 EoS allowed a good description of both solubility and

  8. Grouting mixture

    Energy Technology Data Exchange (ETDEWEB)

    Klyusov, A A; Bakshutov, V S; Kulyavtsev, V A

    1980-10-23

    A grouting mixture is proposed for low-temperature boreholes. The mixture contains cement, beta gypsum polyhydrate, and calcium chloride, so as to increase the water resistance and strength properties of expanding brick at conditions from 20 to -5/sup 0/ C, the components are in the following ratios: (by wt.-%): cement, 77.45-88.06; beta gypsum polyhydrate, 9.79-19.36; calcium chloride, 2.15-3.19. Grouting mortar for cold boreholes serves as the cement.

  9. Instrumental performance of an etude after three methods of practice.

    Science.gov (United States)

    Vanden Ark, S

    1997-12-01

    For 80 fifth-grade students three practice conditions (mental, mental with physical simulation, and physical with singing) produced significant mean differences in instrumental performance of an etude. No significant differences were found for traditional, physical practice.

  10. Study of the tributyl phosphate - 30% dodecane solvent; Etude du solvant phosphate tributylique - 30 % dodecane

    Energy Technology Data Exchange (ETDEWEB)

    Leroy, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses. Centre d' Etudes Nucleaires, 92 (France)

    1967-07-01

    This study, originating mainly from a literature survey, gives the principal chemical and physical features of the tributyl-phosphate (TBP) agent diluted at 30 volumes per cent in dodecane. The mixture is a very commonly used extractant in nuclear fuel processing. In this paper, the main following points are reported: -) the components (TBP and diluents) -) the TBP-diluents systems (non-loaded), -) the TBP-diluents-water systems, -) TBP-diluents-water-nitric acid systems, and -) industrial solvents. (author) [French] Cette etude, d'origine bibliographique, regroupe les caracteristiques physico-chimiques essentielles du phosphate tributylique (TBP) dilue a 30% en volume dans du dodecane. Ce melange constitue un agent d'extraction tres utilise dans le traitement des combustibles nucleaires. Les principaux points traites sont les suivants: -) les constituants (TBP et diluants), -) les systemes TBP-diluants non charges, -) les systemes TBP-diluants-eau, -) les systemes TBP-diluants-eau-acide nitrique, et -) les solvants industriels. (auteur)

  11. Study of total ionization by {alpha} particles, in pure gases and gaseous mixtures containing metastable atoms, as a function of temperature; Etude de l'ionisation totale par les paricules {alpha}, dans les gaz purs et les melanges gazeux contenant des atomes metastables, en fonction de la temperature

    Energy Technology Data Exchange (ETDEWEB)

    Bristeau, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-07-01

    Experiments have been carried out on the total ionization by alpha particles, in pure gases and gaseous mixtures containing metastable atoms, as a function of temperature. Using a different experimental method, the results for the mean ionization energy at 300 K given by Jesse in 1953 have been confirmed to within 1 per cent. It is established that in pure gases the mean energy W required to form a pair of ions remains constant as the temperature varies from 77 to 300 K. It is shown that there is a temperature effect for W in binary gas mixtures of the type A-B containing meta-stable atoms A{sup *} and an 'impurity' B. A systematic study is made of the change {delta}W in W as a function of the temperature and of the B 'impurity' concentration in the mixtures Ne - Ar, Ne - Kr, Ne - H{sub 2}, Ne - N{sub 2}, Ne - CH{sub 4} and He - Ar. Experiments have been carried out on a ternary gas mixture of the type A - B - C, where C is a second ionizable 'impurity' added to the binary mixture A - B; they show the existence of excited atoms B{sup *} formed from the 'impurity' B. Finally, it is shown that the amount of metastable atoms formed in a pure gas must be very close to the number N{sub 0} of ion pairs, and that there must exist a correlation between the number N{sub 0} of ion pairs and the number {approx_equal} N{sub 0} of metastable atoms created in the pure rare gases. (author) [French] On realise des experiences sur l'ionisation totale par les particules alpha, dans les gaz purs et les melanges gazeux contenant des atomes metastables, en fonction de la temperature. Avec une methode experimentale differente, on retrouve a mieux que 1 pour cent pres les valeurs de l'energie moyenne d'ionisation que JESSE a obtenues en 1953 et a 300 K. On etablit que dans les gaz purs, l'energie moyenne W pour creer une paire d'ions demeure constante, quand la temperature varie entre 77 et 300 K. On met en evidence un effet de temperature sur W, dans les melanges gazeux binaires du type

  12. Numerical and experimental study of the influence of the operational parameters on the formation mechanisms of oxides of nitrogen during the combustion of mixtures of cellulosic and plastic materials; Etude experimentale et numerique de l'influence des parametres operatoires sur les mecanismes de formation des oxydes d'azote lors de la combustion de melanges de materiaux cellulosiques et plastiques

    Energy Technology Data Exchange (ETDEWEB)

    Andzi Barhe, T.

    2004-10-15

    The current thesis was performed within a collaboration between the Laboratoire de Combustion et de Detonique (LCD of the University of Poitiers) and the Laboratoire de Physique et de Chimie d'Environnement (LPCE) of the University of Ouagadougou. It was financed by Agency for Environment and Energy Management (ADEME). The principle object of this study is the optimisation of the combustion process during the incineration of waste. This optimisation is aimed at the reduction of the polluting emissions, principally CO and NO, during the incineration of cellulosic and plastic materials. It involves the analysis of the influence of the operational parameters on the polluting emissions and the control of reaction mechanisms of formation and reduction of these pollutants during the combustion process. Consequently, the study was performed in two parts: an experimental part and a numerical part. The experimental part was realised using a fixed bed counterflow reactor. This setup simulates the combustion within an industrial waste incinerator. The reactor allows the combustion of a vertical layer of waste mixture (wood, cardboard, PET, polyamide) to be followed. Three model mixtures representative of the makeup of household waste were studied in order to determine the influence of the composition of the waste on the emission of pollutants (CO and NO). The obtained results show that this parameter has a practically negligible influence within the tested parameter range. Consequently the formation of pollutants depends on the operating parameters - the equivalence ratio and the temperature. A numerical study of the influence of these parameters in order to show their impact on the mechanisms of pollutant formation and to determine the chemical mechanisms involved in the formation of oxides of nitrogen. The numerical study was performed with software developed at the LCD. This programme based on a detailed chemical model coupled to a simple physical model. It uses the

  13. Study of volumetric properties (PVT) of mixtures made of light hydrocarbons (C1-C4), carbon dioxide and hydrogen sulfide - Experimental measurements through a vibrating tube densimeter and modelling; Etude des proprietes volumetriques (PVT) d'hydrocarbures legers (C1-C4), du dioxyde de carbone et de l'hydrogene sulfure. Mesures par densimetrie a tube vibrant et modelisation

    Energy Technology Data Exchange (ETDEWEB)

    Rivollet, F.

    2005-12-15

    Various pollutant contents (i.e. carbon dioxide, hydrogen sulphide or other sulphur products) are found in produced oils. These latter must undergo a number of transformations and purifications. The design and dimensioning of the corresponding units can well be optimized only if one has reliable and accurate data about phase equilibria and volumetric properties and of course reliable and accurate modeling. This work was devoted partly to measurements of volumetric properties on three binary mixtures (ethane - hydrogen sulphide, ethane - propane and carbon dioxide - hydrogen sulphide). These measurements were carried out using equipment, comprising a vibrating tube densimeter (Paar, model DMA 512 P), which was especially designed and built for this work. The binary mixtures were studied in the 253 to 363 K temperature range from at pressures up to either 20 or 40 MPa. Two calibration methods of the vibrating tube were used: the FPMC method (Forced Path Mechanical Calibration) described in the literature and an original method containing neural network, developed herein. The study undertaken about the modeling of volumetric properties made it possible to highlight the inadequacy of the traditional use of cubic equations of state to represent simultaneously volumetric properties and phase equilibria. Among the equations of state investigated, a close attention however was paid to cubic equations of state because of their very great use in the oil field. A new tool was found to adapt cubic equations of state to the simultaneous and satisfactory representation of volumetric properties and phase equilibria. It concerns the coupling of the cubic Redlich-Kwong-Soave equation of state with volume correction through a neural network. This new model was tested successfully, it makes it possible to benefit from the existing work of representation of phase equilibria (mixing rules and interaction coefficients) while improving calculation of the volumetric data.

  14. PENULISAN ETUDE-ETUDE MUSIK TALEMPONG UNGGAN (Sebuah Usaha Pembelajaran Musik Tradisi Berbasis Literatur

    Directory of Open Access Journals (Sweden)

    Asri MK

    2014-12-01

    Full Text Available “Talempong unggan”, a traditional music from Minangkabau community particularly in Unggan, Sumpur Kudus, Sijunjung Regency, West Sumatera Indonesia is classified into genre of “talempong duduak” (rea. Due to its special musical concept and the playing technics, this traditional music is selected as a practising course in the Karawitan Department of Indonesian Institute of Art (ISI Padang Panjang since 1993 till now. In a system of class learning with many students, Talempong Unggan definitely needs supporting methods and learning technics suitable for the course where the students can reach their maximum skills. All the melody of “talempong unggan” that has been made as a material of practice is transcribed to the system of numeric notation and rhythm motive of “gendang” and “aguang” which is written into signs and special notation. All of qualitative data is formulated into finding methods, technics and etude of learning ensamble of Talempong Unggan the traditional music that learned in Karawitan Department of ISI Padang Panjang. Key words: Talempong Unggan, Methods, Technics, Etude

  15. Triptycene dimethyl-bridgehead dianhydride-based intrinsically microporous hydroxyl-functionalized polyimide for natural gas upgrading

    KAUST Repository

    Alghunaimi, Fahd; Ghanem, Bader; Alaslai, Nasser Y.; Mukaddam, Mohsin Ahmed; Pinnau, Ingo

    2016-01-01

    , TDA1-APAF polyimide had a N2/CH4 selectivity of 2.3, thereby making it potentially possible to bring natural gas with low, but unacceptable nitrogen content to pipeline specification. Gas mixture permeation experiments with a 1:1 CO2/CH4 feed mixture

  16. Implementing Formative Assessment in Engineering Education: The Use of the Online Assessment System Etude

    Science.gov (United States)

    Dopper, Sofia M.; Sjoer, Ellen

    2004-01-01

    This article describes the possibilities offered by the online assessment system Etude to achieve the benefits of formative assessment. In order to find out the way this works in practice, we carried out an experiment with the use of Etude for formative assessment in the course on collaborative report writing. Results show that online formative…

  17. Optimal mixture experiments

    CERN Document Server

    Sinha, B K; Pal, Manisha; Das, P

    2014-01-01

    The book dwells mainly on the optimality aspects of mixture designs. As mixture models are a special case of regression models, a general discussion on regression designs has been presented, which includes topics like continuous designs, de la Garza phenomenon, Loewner order domination, Equivalence theorems for different optimality criteria and standard optimality results for single variable polynomial regression and multivariate linear and quadratic regression models. This is followed by a review of the available literature on estimation of parameters in mixture models. Based on recent research findings, the volume also introduces optimal mixture designs for estimation of optimum mixing proportions in different mixture models, which include Scheffé’s quadratic model, Darroch-Waller model, log- contrast model, mixture-amount models, random coefficient models and multi-response model.  Robust mixture designs and mixture designs in blocks have been also reviewed. Moreover, some applications of mixture desig...

  18. 98 Etude Comparative du Systeme Phonematique et Tonal des ...

    African Journals Online (AJOL)

    98. Etude Comparative du Systeme Phonematique et Tonal des. Deux Parlers: Le Yoruba du Nigeria et L'itsa Parle en. Republique du Benin. Ajani Akinwumi Lateef et Ayuba G. Ajibabi http://dx.doi./org/10.4314/ujah.v18i3.5. Résume. En ce début de l'époque ou la mondialisation et la coexistence des peuples dans le ...

  19. Nuclear study of Melusine; Etude nucleaire de Melusine

    Energy Technology Data Exchange (ETDEWEB)

    Cherot, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    In this report are reviewed - with respect to starting of experiments - the main nuclear characteristics of a 20 per cent enriched uranium lattice, with light water as moderator and reflector. The reactor is to operate at 1 MW. 1) Study of various critical masses. 2) Control. Effectiveness of cadmium. Control rods and of a stainless steel regulating rod. 3) Study of the effect on reactivity of disturbances in the core center. 4) Study of xenon and samarium poisoning. 5) Temperature factor. 6) Heat exchanges in a fuel element. (author) [French] On etudie, dans ce rapport, les principales proprietes nucleaires d'un reseau a uranium enrichi (20 pour cent), dont le moderateur et le reflecteur sont l'eau legere en vue des experiences de demarrage. Ce reacteur devra fonctionner a 1 MW. 1) Etude de diverses masses critiques. 2) Controle. Efficacite des barres de controle en cadmium et d'une barre de reglage en acier inoxydable. 3) Etude de l'effet sur la reactivite de perturbation au centre du coeur. 4) Etude de l'empoisonnement xenon et samarium. 5) Coefficient de temperature. 6) Echanges thermiques dans un element. (auteur)

  20. Liquids and liquid mixtures

    CERN Document Server

    Rowlinson, J S; Baldwin, J E; Buckingham, A D; Danishefsky, S

    2013-01-01

    Liquids and Liquid Mixtures, Third Edition explores the equilibrium properties of liquids and liquid mixtures and relates them to the properties of the constituent molecules using the methods of statistical thermodynamics. Topics covered include the critical state, fluid mixtures at high pressures, and the statistical thermodynamics of fluids and mixtures. This book consists of eight chapters and begins with an overview of the liquid state and the thermodynamic properties of liquids and liquid mixtures, including vapor pressure and heat capacities. The discussion then turns to the thermodynami

  1. Study of some properties of zirconium phosphate; Etude de quelques proprietes du phosphate de zirconium

    Energy Technology Data Exchange (ETDEWEB)

    Prospert, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-05-01

    Zirconium phosphate has been studied with a view to using it as an ion exchanger: the first objective was to develop a method of preparation easy to apply and also reproducible. To this end, several tests were carried out varying the molar ratios of phosphorus and of zirconium. Some physical properties such as the diffraction of X-rays were examined. The work then involved certain chemical properties, particularly the percentages of free water and structural water given by the loss on calcination, the Karl-Fisher method and the weight losses by thermogravimetry. Finally an attempts was made to apply the exchanger to the separation of alkaline ions. The static tests showed that the order of fixation of these ions was Cs{sup +} > Rb{sup +} >> K{sup +} > Na{sup +}. Tests with columns showed that Na{sup +} and K{sup +} were easily separable, as was the Rb{sup +}-Cs{sup +} mixture, this last pair being fairly difficult to dissociate. (author) [French] Le phosphate de zirconium a ete etudie en vue de son utilisation comme echangeur d'ions: le premier but a atteindre a ete de mettre au point une preparation pouvant se reveler facilement utilisable ainsi qu'aisement reproductible. A cet effet, plusieurs essais ont ete effectues en faisant varier les rapports molaires du phosphore et du zirconium. Quelques proprietes physiques, telle la diffraction des rayons X, ont ete abordees. Ensuite, l'etude a porte sur certaines proprietes chimiques, particulierement les pourcentages d'eau libre et d'eau de structure par des pertes au feu, utilisation de la methode de Karl-Fisher, ainsi que des pertes de poids a la thenmobalance. Enfin, on a tente d'utiliser l'echangeur a la separation des ions alcalins. Les etudes statiques ont permis de constater que l'ordre de fixation de ces ions etait Cs{sup +} > Rb{sup +} >> K{sup +} > Na{sup +}. Les essais effectues en colonne ont montre que Na{sup +} et K{sup +} etaient aisement separables entre eux, ainsi que du couple Rb{sup +}-Cs{sup +}, ce

  2. Vehicle emissions of greenhouse gases and related tracers from a tunnel study: : CO: CO2, N2O: CO2, CH4: CO2, O2: CO2 ratios, and the stable isotopes 13C and 18O in CO2 and CO

    NARCIS (Netherlands)

    Popa, Maria Elena; Vollmer, M. K.; Jordan, A.; Brand, W. A.; Pathirana, S. L.; Rothe, M.; Röckmann, T.

    2014-01-01

    Measurements of CO2, CO, N2O and CH4 mole fractions, O2/N2 ratios and the stable isotopes 13C and 18O in CO2 and CO have been performed in air samples from the Islisberg highway tunnel (Switzerland). The molar CO : CO2 ratios, with an average of (4.15 ± 0.34) ppb:ppm, are lower than reported in

  3. On the subtle balance between competitive sorption and plasticization effects in asymmetric hollow fiber gas separation membranes

    NARCIS (Netherlands)

    Visser, Tymen; Koops, G.H.; Wessling, Matthias

    2005-01-01

    The paper describes the influence of a varying feed composition of CO2/CH4 and CO2/N2 mixtures on the gas separation performance of integrally skinned asymmetric PES/PI hollow fibers with an effective skin thickness of 0.27 ¿m. Normally, thin membrane structures (<3 ¿m) show accelerated

  4. Simultaneous multi-laser, multi-species trace-level sensing of gas mixtures by rapidly swept continuous-wave cavity-ringdown spectroscopy.

    Science.gov (United States)

    He, Yabai; Kan, Ruifeng; Englich, Florian V; Liu, Wenqing; Orr, Brian J

    2010-09-13

    The greenhouse-gas molecules CO(2), CH(4), and H(2)O are detected in air within a few ms by a novel cavity-ringdown laser-absorption spectroscopy technique using a rapidly swept optical cavity and multi-wavelength coherent radiation from a set of pre-tuned near-infrared diode lasers. The performance of various types of tunable diode laser, on which this technique depends, is evaluated. Our instrument is both sensitive and compact, as needed for reliable environmental monitoring with high absolute accuracy to detect trace concentrations of greenhouse gases in outdoor air.

  5. Perception of trigeminal mixtures.

    Science.gov (United States)

    Filiou, Renée-Pier; Lepore, Franco; Bryant, Bruce; Lundström, Johan N; Frasnelli, Johannes

    2015-01-01

    The trigeminal system is a chemical sense allowing for the perception of chemosensory information in our environment. However, contrary to smell and taste, we lack a thorough understanding of the trigeminal processing of mixtures. We, therefore, investigated trigeminal perception using mixtures of 3 relatively receptor-specific agonists together with one control odor in different proportions to determine basic perceptual dimensions of trigeminal perception. We found that 4 main dimensions were linked to trigeminal perception: sensations of intensity, warmth, coldness, and pain. We subsequently investigated perception of binary mixtures of trigeminal stimuli by means of these 4 perceptual dimensions using different concentrations of a cooling stimulus (eucalyptol) mixed with a stimulus that evokes warmth perception (cinnamaldehyde). To determine if sensory interactions are mainly of central or peripheral origin, we presented stimuli in a physical "mixture" or as a "combination" presented separately to individual nostrils. Results showed that mixtures generally yielded higher ratings than combinations on the trigeminal dimensions "intensity," "warm," and "painful," whereas combinations yielded higher ratings than mixtures on the trigeminal dimension "cold." These results suggest dimension-specific interactions in the perception of trigeminal mixtures, which may be explained by particular interactions that may take place on peripheral or central levels. © The Author 2014. Published by Oxford University Press. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  6. Iterative Mixture Component Pruning Algorithm for Gaussian Mixture PHD Filter

    Directory of Open Access Journals (Sweden)

    Xiaoxi Yan

    2014-01-01

    Full Text Available As far as the increasing number of mixture components in the Gaussian mixture PHD filter is concerned, an iterative mixture component pruning algorithm is proposed. The pruning algorithm is based on maximizing the posterior probability density of the mixture weights. The entropy distribution of the mixture weights is adopted as the prior distribution of mixture component parameters. The iterative update formulations of the mixture weights are derived by Lagrange multiplier and Lambert W function. Mixture components, whose weights become negative during iterative procedure, are pruned by setting corresponding mixture weights to zeros. In addition, multiple mixture components with similar parameters describing the same PHD peak can be merged into one mixture component in the algorithm. Simulation results show that the proposed iterative mixture component pruning algorithm is superior to the typical pruning algorithm based on thresholds.

  7. Mixtures Estimation and Applications

    CERN Document Server

    Mengersen, Kerrie; Titterington, Mike

    2011-01-01

    This book uses the EM (expectation maximization) algorithm to simultaneously estimate the missing data and unknown parameter(s) associated with a data set. The parameters describe the component distributions of the mixture; the distributions may be continuous or discrete. The editors provide a complete account of the applications, mathematical structure and statistical analysis of finite mixture distributions along with MCMC computational methods, together with a range of detailed discussions covering the applications of the methods and features chapters from the leading experts on the subject

  8. Treatment of effluent at the Saclay Centre d'Etudes Nucleaires (1960); Le traitement des effluents du Centre d'Etudes Nucleaires de Saclay (1960)

    Energy Technology Data Exchange (ETDEWEB)

    Wormser, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    The Centre d'Etudes Nucleaires at Saclay possesses several installations from which liquid radioactive effluent is rejected, and it has thus been found necessary to construct a station for the purification of radioactive liquids and to settle various chemical, analytical and technological problems. This report describes, in the following order: - the disposal possibilities at the Centre d'Etudes Nucleaires, Saclay, - the effluents produced at the centre, - the set-up for collecting effluent, - treatment of the effluent, - results of these treatments. (author) [French] La presence, au Centre d'Etudes Nucleaires de Saclay, de plusieurs installations susceptibles de rejeter des effluents liquides radioactifs a necessite la construction d'une station d'epuration d'eaux radioactives et la mise au point de differents problemes chimiques, analytiques et technologiques. Dans ce rapport, nous exposerons successivement: - les possibilites de rejet du Centre d'Etudes Nucleaires de Saclay, - les effluents du centre, - le dispositif de collecte des effluents, - le traitement de ces effluents, - les resultats de ces traitements. (auteur)

  9. Etudes sur le Portugal au Temps de l'Humanisme

    Directory of Open Access Journals (Sweden)

    J. Cruz Costa

    1953-06-01

    Full Text Available BATAILLON (Marcel. — Etudes sur le Portugal au Temps de l'Humanisme.  Acta Universitatis Conimbrigencis, 1952, 309 pp. (Primeiro Parágrafo do Artigo O Prof. Marcel Bataillon, erudito dos mais inteligentes da França atual, autor de uma obra que é hoje impr:scindível para quem pretenda estudar o humanismo renascentista na Espanha ou em Portugal, diríamos melhor, talvez: para quem pretenda estudar o Humanismo e a Renascença, — acaba de publicar, na coleção Acta Universitatis Conimbrigencis, êste volume no qual reune alguns trabalhos da mais alta importância para o conhecimento de muitos aspectos da vida espiritual portuguêsa do século XVI.

  10. I-optimal mixture designs

    OpenAIRE

    GOOS, Peter; JONES, Bradley; SYAFITRI, Utami

    2013-01-01

    In mixture experiments, the factors under study are proportions of the ingredients of a mixture. The special nature of the factors in a mixture experiment necessitates specific types of regression models, and specific types of experimental designs. Although mixture experiments usually are intended to predict the response(s) for all possible formulations of the mixture and to identify optimal proportions for each of the ingredients, little research has been done concerning their I-optimal desi...

  11. Mixtures and interactions

    NARCIS (Netherlands)

    Groten, J.P.

    2000-01-01

    Drinking water can be considered as a complex mixture that consists of tens, hundreds or thousands of chemicals of which the composition is qualitatively and quantitatively not fully known. From a public health point of view it is most relevant to answer the question of whether chemicals in drinking

  12. Studies of elements used in hertzian interferometry (millimetric waves). Measurement of the permittivity of a liquid dielectric; Etudes d'elements utilises en interferometrie hertzienne (ondes millimetriques). Mesure de la permittivite de dielectrique liquide

    Energy Technology Data Exchange (ETDEWEB)

    Dagai, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-12-01

    Study of some elements used in EHF interferometry (bond of millimeter waves). This study is about design of the following elements: horns, horns associated with lens, power separators: -) Study of assemblies allowing measurements of complex dielectric constants of liquids. These devices are used in free propagation about wave lengths {<=} 2 mm; -) Studied devices: Interferometer for 2 separated waves and Michelson's type interferometer; -) 4 liquids have been used: {epsilon}'{sub r} Octane from -50 to 70 C (-58 to 158 F), {epsilon}'{sub r} and {epsilon}'' [Monochlorobenzene at 22,8 C (73 F), Mixture of octane with 10,8 per cent citral at 22 C (72 F) and Benzene at 21 C (70 F)]. -) Precision obtained about measurements: {delta}{epsilon}'/{epsilon}' de 1 a 2%, {delta}{epsilon}''/{epsilon}'' de 4 a 6%.(author) [French] Etudes d'elements utilises en interferometrie hertzienne fonctionnant en ondes millimetriques. Cette etude porte sur la realisation des elements suivants: cornets, cornets associes aux lentilles, separateurs de puissance. Etudes des montages permettant les mesures de la constante dielectrique complexe des corps liquides. Ces montages fonctionnent en propagation libre, sur des longueurs d'onde inferieures ou egales a 2 millimetres. Les montages etudies sont: interferometre a deux ondes separees et interferometre du type Michelson. De plus 4 liquides ont ete etudies: {epsilon}'{sub r} octane de -50 a 70 C, {epsilon}'{sub r} et {epsilon}'' [monochlorobenzene a 22,8 C et melange octane avec 10,8 pour cent citral a 22 C, Benzene a 21 C]. Les precisions obtenues sur les mesures sont: {delta}{epsilon}'/{epsilon}' de 1 a 2 pour cent, {delta}{epsilon}''/{epsilon}'' de 4 a 6 pour cent.

  13. Contribution to the study of uranyl salts in butyl phosphate solutions; Contribution a l'etude des solutions de sels d'uranyle dans les phosphates butyliques

    Energy Technology Data Exchange (ETDEWEB)

    Coulon, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1965-06-01

    A spectroscopic study in the normal infrared region and involving the following associations: tri-alkyl phosphates (tri-butyl, tri-ethyl, tri-methyl), uranyl salts (nitrate, chloride, acetate) has confirmed the existence of an interaction between the phosphoryl group and the uranium atom, as shown by a movement of absorption band for the valency P = 0 from {approx} 1270 cm{sup -1} to {approx} 1180 cm{sup -1}. A study of the preparation, analysis and spectroscopy of the solids obtained by the precipitation of uranyl salts by acid butyl phosphates has been carried out. By infrared spectrophotometry it has been shown that the tri-butyl and di-butyl phosphates are associated in non-polar diluents even before the uranium is introduced. The extraction of uranyl salts from acid aqueous solutions by a diluted mixture of tri-butyl and di-butyl phosphates proceeds by different mechanisms according to the nature of the ion (nitrate or chloride). (author) [French] Une etude spectroscopique dans l'infrarouge moyen portant sur les associations: - phosphates trialcoyliques (tributylique - triethylique - trimethylique) - sels d'uranyle (nitrate, chlorure, acetate) a confirme l'existence d'une interaction entre le groupement phosphoryle et l'atome d'uranium, se manifestant par un deplacement de la bande d'absorption de la vibration de valence P = 0 de {approx} 1270 cm{sup -1} a {approx} 1180 cm{sup -1}. Une etude preparative, analytique et spectroscopique des solides obtenus par precipitation de sels d'uranyle par les phosphates butyliques acides a ete effectuee. La spectrophotomerie infrarouge met en evidence l'association, anterieure a toute introduction d'uranium, des phosphates tributylique et dibutylique dans des diluants non polaires. L'extraction de sels d'uranyle, d'une solution aqueuse acide par un melange dilue de phosphates tributylique et dibutylique, s'effectue suivant des processus differents a la nature de l'anion (nitrate ou chlorure). (auteur)

  14. Mixture based outlier filtration

    Czech Academy of Sciences Publication Activity Database

    Pecherková, Pavla; Nagy, Ivan

    2006-01-01

    Roč. 46, č. 2 (2006), s. 30-35 ISSN 1210-2709 R&D Projects: GA MŠk 1M0572; GA MDS 1F43A/003/120 Institutional research plan: CEZ:AV0Z10750506 Keywords : data filtration * system modelling * mixture models Subject RIV: BD - Theory of Information http://library.utia.cas.cz/prace/20060165.pdf

  15. Mixture for plugging absorption zones

    Energy Technology Data Exchange (ETDEWEB)

    Sitinkov, G V; Kovalenko, N G; Makarov, L V; Zinnatulchin, Ts Kh

    1981-01-17

    A mixture is proposed for plugging absorption zones. The mixture contains synthetic polymer and a solvent. So as to increase the penetrability of the mixture through a reduction in its viscosity and an increase in insulation properties, the compound contains either Capron or Neilon as the synthetic polyamide resin polmyer, and concentrated chloride as the solvent. The mixture is prepared in a special AzINMASh-30 unit (acid cart). After the mixture has been produced, it is injected into the borehole by means of an acid cart pump. So as to prevent coaggulation at the point when the mixture in injected into the stratum through tubes, the mixture is placed betwen chemically inert fluids, for example, a clay mortar. The inert and compressed fluids are injected by means of a cementing unit. The entire process of production and application of the mixture is simple and fully automated through the use of well-known equipment.

  16. Contribution to the study of several chemical hazards in the Centre d'Etudes Nucleaires of Fontenay-aux-Roses; Contribution a l'etude de quelques nuisances chimiques au centre d'etudes nucleaires de Fontenay-aux-Roses

    Energy Technology Data Exchange (ETDEWEB)

    Megemont, C; Grau, C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-10-01

    From the checking of 2750 index cards of hazards, the study relates the distribution of the chemical hazards in the Centre d'Etudes Nucleaires of Fontenay-aux-Roses. Those concerning the greatest number of agents in the Centre are classified according to the categories corresponding to the different conditions of working. Thus, the most important are put forward. Then, the authors rapidly make a review of hazards which may have some special interest because they appear more specific of the nuclear energy or because they are the most frequently noted on the index cards of hazards. The case of the tributylphosphate is studied more precisely. (authors) [French] A partir de l'examen de 2750 fiches de nuisances, l'etude porte sur la repartition des nuisances chimiques au Centre d'Etudes Nucleaires de Fontenay-aux-Roses. Celles qui concernent le plus grand nombre d'agents du Centre sont classees selon les categories correspondant aux differentes conditions de travail. Les plus importantes d'entre elles sont ainsi mises en evidence. | Les auteurs passent ensuite en revue, rapidement, les nuisances qui peuvent presenter un interet particulier soit parce qu'elles semblent plus specifiques de l'Energie Nucleaire, soit parce qu'on les rencontre le plus frequemment sur les fiches de nuisances. Le cas du tributylphosphate est envisage de facon plus detaillee. (auteurs)

  17. Separating Underdetermined Convolutive Speech Mixtures

    DEFF Research Database (Denmark)

    Pedersen, Michael Syskind; Wang, DeLiang; Larsen, Jan

    2006-01-01

    a method for underdetermined blind source separation of convolutive mixtures. The proposed framework is applicable for separation of instantaneous as well as convolutive speech mixtures. It is possible to iteratively extract each speech signal from the mixture by combining blind source separation...

  18. Mixtures of truncated basis functions

    DEFF Research Database (Denmark)

    Langseth, Helge; Nielsen, Thomas Dyhre; Rumí, Rafael

    2012-01-01

    In this paper we propose a framework, called mixtures of truncated basis functions (MoTBFs), for representing general hybrid Bayesian networks. The proposed framework generalizes both the mixture of truncated exponentials (MTEs) framework and the mixture of polynomials (MoPs) framework. Similar t...

  19. Prevalence Incidence Mixture Models

    Science.gov (United States)

    The R package and webtool fits Prevalence Incidence Mixture models to left-censored and irregularly interval-censored time to event data that is commonly found in screening cohorts assembled from electronic health records. Absolute and relative risk can be estimated for simple random sampling, and stratified sampling (the two approaches of superpopulation and a finite population are supported for target populations). Non-parametric (absolute risks only), semi-parametric, weakly-parametric (using B-splines), and some fully parametric (such as the logistic-Weibull) models are supported.

  20. Etude de la qualité physico-chimique et biologique des eaux du ...

    African Journals Online (AJOL)

    Etude de la qualité physico-chimique et biologique des eaux du fleuve Niger à Niamey. ... le récepteur principal des rejets d'eaux usées de la ville de Niamey, capital du ... La description de ces taxons montre une variation de la structure des ...

  1. English Department Reforms at the Hautes Etudes Commerciales: Entering the Nineties.

    Science.gov (United States)

    Shanahan, Daniel

    1993-01-01

    Discusses the reforms made in the fall of 1990 in the English department at the Ecole Hautes Etudes Commerciales (Paris, France), which were based on the basis of a combination of literature-culture and second- and foreign-language acquisition pedagogical biases. (four references) (VWL)

  2. Contribution a l'etude des plantes alimentaires mineures dans la ...

    African Journals Online (AJOL)

    Contribution a l'etude des plantes alimentaires mineures dans la prefecture de Dankpen (Togo). AB Kebenzikato, S Akpavi, K Batawila, K Wala, M Dourma, K Kossi-Titrikou, KS Amouzou, I Butare, H Dantsey-Barry, K Akpagana ...

  3. 152 Etude de cas sur l'impact des amendements organiques vis-à ...

    African Journals Online (AJOL)

    john mukalay

    Etude de cas sur l'impact des amendements organiques vis-à-vis de la salinité en culture de bananier. Michel Mazinga KWEY1, Séverin Kalala BANZE2 et John Banza MUKALAY2*. 1Laboratoire des cultures in vitro, Département de phytotechnie, Faculté des sciences agronomiques,. Université de Lubumbashi, BP 1825, ...

  4. 186 Etude théorique du transport électronique par la simulation ...

    African Journals Online (AJOL)

    youness

    Choukria SAYAH et al. 186. Etude théorique du ... For that we carried out the microscopic simulations, based on the Monte. Carlo method. ... intervalles, piezoelectric as well as the interactions of alloy and on ionized impurities. ..... SAYA et al. 198. [5] - R. W. Hockney, J. W. Eastwood, "Computer simulation using particles",.

  5. Etude comparative de la flore aux abords des cours d'eau dans les ...

    African Journals Online (AJOL)

    Etude comparative de la flore aux abords des cours d'eau dans les zones hypo et hyper endémiques d'ulcère de Buruli en Côte d'Ivoire. C. Cisse Boni, E. Ehouman, D. Soro, M.W. Kone, A. Bakayoko, F. Dembele, K. Bauthire, M Dosso ...

  6. Treatment of refractory powders by a novel, high enthalpy dc plasma

    Science.gov (United States)

    Pershin, L.; Mitrasinovic, A.; Mostaghimi, J.

    2013-06-01

    Thermophysical properties of CO2-CH4 mixtures at high temperatures are very attractive for materials processing. In comparison with argon, at the same temperature, such a mixture possesses much higher enthalpy and higher thermal conductivity. At high temperatures, CO2-CH4 mixture has a complex composition with strong presence of CO which, in the case of powder treatment, could reduce oxidation. In this work, a dc plasma torch with graphite cathode was used to study the effect of plasma gas composition on spheroidization of tungsten carbide and alumina powders. Two different gas compositions were used to generate the plasma while the torch current was kept at 300 A. Various techniques were employed to assess the average concentration of carbides and oxides and the final shape of the treated powders. Process parameters such as input power and plasma gas composition allow controlling the degree of powder oxidation and spheroidization of high melting point ceramic powders.

  7. Separation of gas mixtures

    International Nuclear Information System (INIS)

    1981-01-01

    Apparatus is described for the separation of a gaseous plasma mixture into components in some of which the original concentration of a specific ion has been greatly increased or decreased, comprising: a source for converting the gaseous mixture into a train of plasma packets; an open-ended vessel with a main section and at least one branch section, adapted to enclose along predetermined tracks the original plasma packets in the main section, and the separated plasma components in the branch sections; drive means for generating travelling magnetic waves along the predetermined tracks with the magnetic flux vector of the waves transverse to each of the tracks; and means for maintaining phase coherence between the plasma packets and the magnetic waves at a value needed for accelerating the components of the packets to different velocities and in such different directions that the plasma of each packet is divided into distinctly separate packets in some of which the original concentration of a specific ion has been greatly increased or decreased, and which plasma packets are collected from the branch sections of the vessels. (author)

  8. Alecto 2 - interaction studies; Alecto 2 - etudes d'interaction

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, J P; Clouet d' Orval, Ch; Mougniot, J C; Penet, F [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-07-01

    Weak interactions were experimentally studies with the tank of the critical assembly Alecto II and one, two or three bottles containing solutions of various concentrations. In particular, was studied the validity of certain classical assumptions, shielding effects, screening and semi-reflexion effects, importance of thermal coupling. The method of the 'k{sub eff}, solid angle' is shown to apply to such a system. The determination by divergence and pulsed neutron technique of the reactivity related to a millimeter of solution level affords the obtention of critical heights in terms of reactivity. (authors) [French] Une etude experimentale d'interactions faibles a ete faite entre la cuve de l'experience critique ALECTO II et une, deux ou trois bouteilles contenant des concentrations variees. On etudie, en particulier, la validite de certaines hypotheses classiques, effets d'ombre, d'ecrans, de semi-reflexion, importance du couplage thermique. On montre d'autre part que la methode du 'K{sub eff}, angle solide' peut s'appliquer a un tel systeme. La determination par divergence et neutrons pulses de la reactivite liee au millimetre de solution permet de traduire les hauteurs critiques obtenues, en terme de reactivite. (auteurs)

  9. Baby fission chambers; Etude de chambres a fission miniatures

    Energy Technology Data Exchange (ETDEWEB)

    Guery, U; Tachon, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-07-01

    The present report is intended, on the one band, as a study of the main types of fission chambers produced to date, and on the other, to deal more generally with this type of detector. Originally, it was with a view to the charting of neutron scatter in 'Proserpine' that the authors undertook the study of these chambers. During the course of the task, it was considered worth tbe trouble of developing its scope to include a more general application: neutron scatter measurement of various energy neutrons within a reduced volume with slight local disturbance. (author) [French] Le present rapport se propose, d'une part, d'exposer les principales realisations de chambres a fission, d'autre part de faire une mise au point a caractere plus general sur ces detecteurs. Au depart, c'est surtout en vue des mesures de densite neutronique dans 'Proserpine' que les auteurs ont etudie ces chambres; au cours de la mise au point, il a paru interessant de developper leur etude pour des applications plus generales: mesures de densites de neutrons de differentes energies dans un element de volume tres reduit et avec faible perturbation locale. (auteur)

  10. SEPA (Service d'etudes, de Procedes et Analyses)

    International Nuclear Information System (INIS)

    2017-01-01

    The SEPA (Service d'etudes, de Procedes et Analyses), is an engineering department specializing in the analysis and processing of uranium ore. It comes from a long tradition of mining in France that began sixty-five years ago with the French Atomic Energy Commission (CEA) and that has been carried on by COGEMA and then Areva. SEPA brings a combination of experience and excellence to its activities thanks to its multidisciplinary staff (mineralogists, chemists, mechanical engineers, instrumentation specialists...), who come from diverse cultural backgrounds. Today, the SEPA draws on its wealth of know-how and expertise to devise and develop new methods for processing and valorizing ores everywhere in the world. Its mission is to: - Develop and conduct laboratory tests on methods for processing uranium and other valuable elements such as molybdenum, vanadium, rare earths, niobium, tantalum and thorium; - Analyze ores obtained during prospecting at locations all over the world; -Serve as an advisor in the commissioning of Areva industrial units and ore processing plants; -Perform environmental analyses during the full period of mining operations; -Conduct audits and provide advice on processes and analysis methods; -Carry out research and development in all aspects of minerals treatment (including the filing of patents). The SEPA combines experience, skills and a global approach to technologies used in ore processing. Its role is to continually improve the processes for extracting, processing and valorizing ores while protecting the environment

  11. Baby fission chambers; Etude de chambres a fission miniatures

    Energy Technology Data Exchange (ETDEWEB)

    Guery, U.; Tachon, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1957-07-01

    The present report is intended, on the one band, as a study of the main types of fission chambers produced to date, and on the other, to deal more generally with this type of detector. Originally, it was with a view to the charting of neutron scatter in 'Proserpine' that the authors undertook the study of these chambers. During the course of the task, it was considered worth tbe trouble of developing its scope to include a more general application: neutron scatter measurement of various energy neutrons within a reduced volume with slight local disturbance. (author) [French] Le present rapport se propose, d'une part, d'exposer les principales realisations de chambres a fission, d'autre part de faire une mise au point a caractere plus general sur ces detecteurs. Au depart, c'est surtout en vue des mesures de densite neutronique dans 'Proserpine' que les auteurs ont etudie ces chambres; au cours de la mise au point, il a paru interessant de developper leur etude pour des applications plus generales: mesures de densites de neutrons de differentes energies dans un element de volume tres reduit et avec faible perturbation locale. (auteur)

  12. Research of Deformation of Clay Soil Mixtures Mixtures

    OpenAIRE

    Romas Girkontas; Tadas Tamošiūnas; Andrius Savickas

    2014-01-01

    The aim of this article is to determine clay soils and clay soils mixtures deformations during drying. Experiments consisted from: a) clay and clay mixtures bridges (height ~ 0,30 m, span ~ 1,00 m); b) tiles of clay and clay, sand and straw (height, length, wide); c) cylinders of clay; clay and straw; clay, straw and sand (diameter; height). According to the findings recommendations for clay and clay mixtures drying technology application were presented. During the experiment clay bridge bear...

  13. Mutagenicity of complex mixtures

    International Nuclear Information System (INIS)

    Pelroy, R.A.

    1985-01-01

    The effect of coal-derived complex chemical mixtures on the mutagenicity of 6-aminochrysene (6-AC) was determined with Salmonella typhimurium TA98. Previous results suggested that the mutagenic potency of 6-AC for TA98 in the standard microsomal activation (Ames) assay increased if it was presented to the cells mixed with high-boiling coal liquids (CL) from the solvent refined coal (SRC) process. In this year's work, the apparent mutational synergism of CL and 6-AC was independently verified in a fluctuation bioassay which allowed quantitation of mutational frequencies and cell viability. The results of this assay system were similar to those in the Ames assay. Moreover, the fluctation assay revealed that mutagenesis and cellular toxicity induced by 6-AC were both strongly enhanced if 6-AC was presented to the cells mixed in a high-boiling CL. 4 figures

  14. Experiments on neutron-attenuation by ordinary concrete; Etude experimentale de l'attenuation des neutrons dans le beton ordinaire

    Energy Technology Data Exchange (ETDEWEB)

    Beauge, R; Millot, J P; Rastoin, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1959-07-01

    The penetration of fission-neutrons in water and glass mixtures has been investigated in the NAIADE facility. The slopes of the thermal and fast fluxes (the latter measured with a dosimeter) remain similar when the volume proportion of water is greater than 15 per cent. For smaller water-contents the measurements show the evidence of streaming, presumably due to slowing-down neutrons of energy smaller than 300 keV. Since a volume proportion of about 15 per cent of water in glass corresponds to the composition of ordinary concrete, the present work enables to predict the effects of a desiccation of concrete. Moreover, it is seen that there is no interest in increasing the proportion of water in ordinary concrete beyond the usual values (15-20 per cent). (author) [French] La propagation des neutrons de fission a ete etudiee dans les melanges verre-eau au moyen du dispositif NAIADE. La pente du flux thermique et la pente du flux rapide (obtenue au moyen d'un dosimetre) restent voisines lorsque la proportion d'eau dans le melange depasse 15 pour cent en volume. Pour des proportions d'eau inferieures les mesures mettent en evidence un 'streaming' de neutrons en ralentissement d'energie probablement inferieure a 300 keV. La composition des melanges verre-eau aux environs de 15 pour cent d'eau en volume correspondant au beton ordinaire, la presente etude permet de prevoir les effets d'une dessication du beton, et montre, en outre, qu'il n'y a pas interet a essayer d'augmenter la proportion d'eau dans le beton ordinaire au dela des valeurs usuelles (15 a 20 pour cent). (auteur)

  15. Etude aerodynamique d'un jet turbulent impactant une paroi concave

    Science.gov (United States)

    LeBlanc, Benoit

    Etant donne la demande croissante de temperatures elevees dans des chambres de combustion de systemes de propulsions en aerospatiale (turbomoteurs, moteur a reaction, etc.), l'interet dans le refroidissement par jets impactant s'est vu croitre. Le refroidissement des aubes de turbine permet une augmentation de temperature de combustion, ce qui se traduit en une augmentation de l'efficacite de combustion et donc une meilleure economie de carburant. Le transfert de chaleur dans les au bages est influence par les aspects aerodynamiques du refroidissement a jet, particulierement dans le cas d'ecoulements turbulents. Un manque de comprehension de l'aerodynamique a l'interieur de ces espaces confinees peut mener a des changements de transfert thermique qui sont inattendus, ce qui augmente le risque de fluage. Il est donc d'interet pour l'industrie aerospatiale et l'academie de poursuivre la recherche dans l'aerodynamique des jets turbulents impactant les parois courbes. Les jets impactant les surfaces courbes ont deja fait l'objet de nombreuses etudes. Par contre des conditions oscillatoires observees en laboratoire se sont averees difficiles a reproduire en numerique, puisque les structures d'ecoulements impactants des parois concaves sont fortement dependantes de la turbulence et des effets instationnaires. Une etude experimentale fut realisee a l'institut PPRIME a l'Universite de Poitiers afin d'observer le phenomene d'oscillation dans le jet. Une serie d'essais ont verifie les conditions d'ecoulement laminaires et turbulentes, toutefois le cout des essais experimentaux a seulement permis d'avoir un apercu du phenomene global. Une deuxieme serie d'essais fut realisee numeriquement a l'Universite de Moncton avec l'outil OpenFOAM pour des conditions d'ecoulement laminaire et bidimensionnel. Cette etude a donc comme but de poursuivre l'enquete de l'aerodynamique oscillatoire des jets impactant des parois courbes, mais pour un regime d'ecoulement transitoire, turbulent

  16. Complex mixtures biostudies

    International Nuclear Information System (INIS)

    Springer, D.L.

    1987-01-01

    The objective of the project is to identify potential adverse biological activities associated with human exposures to complex organic mixtures (COM) from energy-related industries. Studies to identify the influence of chemical class fractions from a COM on the initiating activity of a known carcinogen, benzo(a)pyrene (BaP), demonstrated that the polycyclic aromatic hydrocarbons (PAH) and nitrogen-containing polycyclic aromatic compound (NPAC) fractions were the most effective inhibitors of initiation. In an effort to determine the contribution of BaP to the initiating activity of the COM, binding of radiolabeled BaP to mouse skin DNA was measured. Results indicated that binding of BaP to DNA decreased in the presence of the COM so that at initiating COM doses, BaP binding was near the limit detection. Addition of unlabeled BaP to the COM at an amount similar to that originally present in the COM did not significantly increase the binding. Studies to determine the rates of disappearance of carcinogenic PAH from the site of application on the skin indicated that half-lives for PAH differed by a factor of about 2. Analytical methods developed to identify PAH from COM which covalently bind to DNA demonstrated that the lower level of detection is approximately 200 picograms. Developmental studies demonstrated that both pregnant rats and mice treated dermally with a high-boiling COM developed fetuses with major malformations including cleft palate, small lungs, edema, and sagittal suture hemorrhages. 3 figures, 5 tables

  17. Component effects in mixture experiments

    International Nuclear Information System (INIS)

    Piepel, G.F.

    1980-01-01

    In a mixture experiment, the response to a mixture of q components is a function of the proportions x 1 , x 2 , ..., x/sub q/ of components in the mixture. Experimental regions for mixture experiments are often defined by constraints on the proportions of the components forming the mixture. The usual (orthogonal direction) definition of a factor effect does not apply because of the dependence imposed by the mixture restriction, /sup q/Σ/sub i=1/ x/sub i/ = 1. A direction within the experimental region in which to compute a mixture component effect is presented and compared to previously suggested directions. This new direction has none of the inadequacies or errors of previous suggestions while having a more meaningful interpretation. The distinction between partial and total effects is made. The uses of partial and total effects (computed using the new direction) in modification and interpretation of mixture response prediction equations are considered. The suggestions of the paper are illustrated in an example from a glass development study in a waste vitrification program. 5 figures, 3 tables

  18. Mixtures of skewed Kalman filters

    KAUST Repository

    Kim, Hyoungmoon; Ryu, Duchwan; Mallick, Bani K.; Genton, Marc G.

    2014-01-01

    Normal state-space models are prevalent, but to increase the applicability of the Kalman filter, we propose mixtures of skewed, and extended skewed, Kalman filters. To do so, the closed skew-normal distribution is extended to a scale mixture class

  19. Easy and flexible mixture distributions

    DEFF Research Database (Denmark)

    Fosgerau, Mogens; Mabit, Stefan L.

    2013-01-01

    We propose a method to generate flexible mixture distributions that are useful for estimating models such as the mixed logit model using simulation. The method is easy to implement, yet it can approximate essentially any mixture distribution. We test it with good results in a simulation study...

  20. Magnetic resonance studies of solid polymers; Etude des polymeres solides par resonance magnetique

    Energy Technology Data Exchange (ETDEWEB)

    Lenk, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    This paper is a review of the application of nuclear magnetic resonance (NMR) to solid polymers. In the first, theoretical part, the elements of the theory of NMR, which are necessary for the study of the properties of solid polymers are discussed: the moments method, nuclear relaxation and the distribution of correlation times. In the second part the experimental results are presented. (author) [French] Cette etude est une recherche bibliographique sur l'application de la resonance magnetique nucleaire (RMN) aux polymeres solides. Dans la premiere partie theorique on discute les elements de la theorie de RMN, necessaires pour l'etude des proprietes des polymeres solides: la methode des moments, la relaxation nucleaire et la distribution des temps de correlation. La deuxieme partie presente les resultats des experiences. (auteur)

  1. A general mixture theory. I. Mixtures of spherical molecules

    Science.gov (United States)

    Hamad, Esam Z.

    1996-08-01

    We present a new general theory for obtaining mixture properties from the pure species equations of state. The theory addresses the composition and the unlike interactions dependence of mixture equation of state. The density expansion of the mixture equation gives the exact composition dependence of all virial coefficients. The theory introduces multiple-index parameters that can be calculated from binary unlike interaction parameters. In this first part of the work, details are presented for the first and second levels of approximations for spherical molecules. The second order model is simple and very accurate. It predicts the compressibility factor of additive hard spheres within simulation uncertainty (equimolar with size ratio of three). For nonadditive hard spheres, comparison with compressibility factor simulation data over a wide range of density, composition, and nonadditivity parameter, gave an average error of 2%. For mixtures of Lennard-Jones molecules, the model predictions are better than the Weeks-Chandler-Anderson perturbation theory.

  2. A microcosm of musical expression: II. Quantitative analysis of pianists' dynamics in the initial measures of Chopin's Etude in E major.

    Science.gov (United States)

    Repp, B H

    1999-03-01

    Patterns of expressive dynamics were measured in bars 1-5 of 115 commercially recorded performances of Chopin's Etude in E major, op. 10, No. 3. The grand average pattern (or dynamic profile) was representative of many performances and highly similar to the average dynamic profile of a group of advanced student performances, which suggests a widely shared central norm of expressive dynamics. The individual dynamic profiles were subjected to principal components analysis, which yielded Varimax-rotated components, each representing a different, nonstandard dynamic profile associated with a small subset of performances. Most performances had dynamic patterns resembling a mixture of several components, and no clustering of of performances into distinct groups was apparent. Some weak relationships of dynamic profiles with sociocultural variables were found, most notably a tendency of female pianists to exhibit a greater dynamic range in the melody. Within the melody, there were no significant relationships between expressive timing [Repp, J. Acoust. Soc. Am. 104, 1085-1100 (1998)] and expressive dynamics. These two important dimensions seemed to be controlled independently at this local level and thus offer the artist many degrees of freedom in giving a melody expressive shape.

  3. Study of immiscibilities in the trilaurylamine - dodecane - nitric acid - plutonium system; Etude des immiscibilites dans le systeme trilaurylamine - dodecane - acide nitrique - plutonium

    Energy Technology Data Exchange (ETDEWEB)

    Saey, J C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    Phase equilibrium in systems made up of trilaurylamine, dodecane, nitric acid tetravalent plutonium is shown by drawing the triangular diagrams. the study of these diagrams provides informations concerning the causes of immiscibility. Heterogeneity of the organic mixtures can be related to some characteristics of the components- dipole moment, molecular polarizability and hydrogen bond exchanging ability-Depending on these, some rules may be established which can be used to make a proper choice of an additive in order to improve the miscibility. As an application a study on the partial substitution of dodecane with decalin, in plutonium extraction experiments, has been done showing a possible improvement of the extraction process. (author) [French] L equilibre des phases dans les systemes formes a partir de trilaurylamine, de dodecane, d'acide nitrique et de plutonium tetravalent est represente en tracant les diagrammes triangulaires. L'examen de ces diagrammes permet d'apporter certaines precisions en ce qui concerne l'origine des immiscibilites. Celles ci sont ensuite reliees a certaines caracteristiques des constituants: le moment dipolaire, la polarisabilite moleculaire et la tendance a former des liaisons hydrogene. Sur les memes bases, il est possible d'etablir un certain nombre de regles pouvant servir a guider le choix d'un additif ameliorant la miscibilite. En application, une etude sur le remplacement partiel du dodecane par la decaline montre l'interet de l'emploi de ce compose dans le procede de purification du plutonium. (auteur)

  4. Singing as a Therapeutic Agent, inThe Etude, 1891-1949.

    Science.gov (United States)

    Hunter

    1999-01-01

    The Etude music magazine, founded by Theodore Presser, was one of a number of popular music magazines published in the years prior to the establishment of the music therapy profession in 1950. During its publication run from 1883 to 1957, over 100 music therapy related articles appeared, including 13 on the health benefits of singing published between 1891 and 1949. Written by authors with diverse backgrounds, such as the famous Battle Creek, Michigan physician John Harvey Kellogg and Boston music critic Louis C. Elson, the articles contained consistent and adamant support regarding the health benefits of singing. The advantages described were both physical and psychological, and were recommended prophylactically for well persons and therapeutically for ill persons. Although the articles varied in perspective, from philosophical to theoretical to pedagogical, there is a consistent holistic medicine theme that appeared almost ahead of its time and no doubt linked to the push for vocal music education in that era. The importance of The Etude in promulgating ideas that helped shape the early practice of music therapy should not be underestimated. For much of its publication run The Etude was the largest music periodical in print, reaching its peak circulation of 250,000 copies per month in 1924.

  5. Natural convection in ternary mixtures

    International Nuclear Information System (INIS)

    Kremer, G.M.; Kai, L.

    1981-01-01

    The field equations for a mixture of a viscous fluid, a deformable solid and a non-viscous fluid are studied, based on a linearized theory proposed by Bowen. The fields of density of each constituent, temperature, velocity of each fluid and displacement of the solid are determined, for steady states flow of the mixture between two parallel planes and between two concentric cylinders which are maintained at diferent temperatures. (Author) [pt

  6. Centrifugal separation of mixture gases

    International Nuclear Information System (INIS)

    Zhou, M.S.; Chen, W.N.; Yin, Y.T.

    2008-01-01

    An attempt for single centrifugal separation of mixtures with different molecular formula was presented in this paper. The mixtures of SF 6 and CCl 3 F, and SF 6 and CCl 4 were chosen as the processing gases, which were prepared in three mass ratios, 0.5, 0.8 and 0.2, respectively. The separating characteristics such as the overall separation factors and the variation of cuts were studied. (author)

  7. Performance evaluation of Louisiana superpave mixtures.

    Science.gov (United States)

    2008-12-01

    This report documents the performance of Louisiana Superpave mixtures through laboratory mechanistic tests, mixture : volumetric properties, gradation analysis, and early field performance. Thirty Superpave mixtures were evaluated in this : study. Fo...

  8. Contribution to the micrographic study of uranium and its alloys; Contribution a l'etude micrographique de l'uranium et de ses alliages

    Energy Technology Data Exchange (ETDEWEB)

    Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1956-06-15

    The present report is the result of research carried out by the radio metallurgy section, to perfect micrographic techniques applicable to the study of samples of irradiated uranium. In the first part of this work, two polishing baths are developed, having the qualities with a minimum of disadvantages inherent in their respective compositions: they are, on the one hand perchloric acid-ethanol mixtures, and on the other hand a phospho-chromic-ethanol bath. In the chapter following, the micrographic attack of uranium is studied. The only satisfactory process is oxidation by cathode bombardment forming epitaxic layers. In the third chapter, an attempt is made to characterise the different surface states of the uranium by dissolution potential measurements and electronic diffraction. In the fourth chapter are given some examples of the application of these techniques to the micrographic study of various uranium alloys. In an appendix, it is shown how the chemical oxidation after phospho-chromic-alcohol polishing allows the different inclusions present in the molten uranium to be distinguished. By X-ray diffraction, uranium monocarbide and mononitride inclusions in particular are characterised. (author) [French] Le present rapport est le resultat de recherches effectuees au service de radiometallurgie pour la mise au point de techniques micrographiques applicables a l'etude d'echantillons d'uranium irradie. Dans la premiere partie de ce travail, nous mettons au point deux bains de polissage qui presentent les qualites inherentes a leur composition respective, avec le minimum d'inconvenients: ce sont d'une part des melanges acide perchlorique-ethanol, et d'autre part un bain phospho-chromique-ethanol. Dans le chapitre suivant, nous etudions l'attaque micrographique de l'uranium. Seul le procede d'oxydation par bombardement cathodique formant des couches epitaxiques, est satisfaisant. Dans le troisieme chapitre, nous essayons de caracteriser les differents etats de

  9. Contribution to the micrographic study of uranium and its alloys; Contribution a l'etude micrographique de l'uranium et de ses alliages

    Energy Technology Data Exchange (ETDEWEB)

    Monti, H. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1956-06-15

    The present report is the result of research carried out by the radio metallurgy section, to perfect micrographic techniques applicable to the study of samples of irradiated uranium. In the first part of this work, two polishing baths are developed, having the qualities with a minimum of disadvantages inherent in their respective compositions: they are, on the one hand perchloric acid-ethanol mixtures, and on the other hand a phospho-chromic-ethanol bath. In the chapter following, the micrographic attack of uranium is studied. The only satisfactory process is oxidation by cathode bombardment forming epitaxic layers. In the third chapter, an attempt is made to characterise the different surface states of the uranium by dissolution potential measurements and electronic diffraction. In the fourth chapter are given some examples of the application of these techniques to the micrographic study of various uranium alloys. In an appendix, it is shown how the chemical oxidation after phospho-chromic-alcohol polishing allows the different inclusions present in the molten uranium to be distinguished. By X-ray diffraction, uranium monocarbide and mononitride inclusions in particular are characterised. (author) [French] Le present rapport est le resultat de recherches effectuees au service de radiometallurgie pour la mise au point de techniques micrographiques applicables a l'etude d'echantillons d'uranium irradie. Dans la premiere partie de ce travail, nous mettons au point deux bains de polissage qui presentent les qualites inherentes a leur composition respective, avec le minimum d'inconvenients: ce sont d'une part des melanges acide perchlorique-ethanol, et d'autre part un bain phospho-chromique-ethanol. Dans le chapitre suivant, nous etudions l'attaque micrographique de l'uranium. Seul le procede d'oxydation par bombardement cathodique formant des couches epitaxiques, est satisfaisant. Dans le troisieme chapitre, nous essayons

  10. Nonparametric e-Mixture Estimation.

    Science.gov (United States)

    Takano, Ken; Hino, Hideitsu; Akaho, Shotaro; Murata, Noboru

    2016-12-01

    This study considers the common situation in data analysis when there are few observations of the distribution of interest or the target distribution, while abundant observations are available from auxiliary distributions. In this situation, it is natural to compensate for the lack of data from the target distribution by using data sets from these auxiliary distributions-in other words, approximating the target distribution in a subspace spanned by a set of auxiliary distributions. Mixture modeling is one of the simplest ways to integrate information from the target and auxiliary distributions in order to express the target distribution as accurately as possible. There are two typical mixtures in the context of information geometry: the [Formula: see text]- and [Formula: see text]-mixtures. The [Formula: see text]-mixture is applied in a variety of research fields because of the presence of the well-known expectation-maximazation algorithm for parameter estimation, whereas the [Formula: see text]-mixture is rarely used because of its difficulty of estimation, particularly for nonparametric models. The [Formula: see text]-mixture, however, is a well-tempered distribution that satisfies the principle of maximum entropy. To model a target distribution with scarce observations accurately, this letter proposes a novel framework for a nonparametric modeling of the [Formula: see text]-mixture and a geometrically inspired estimation algorithm. As numerical examples of the proposed framework, a transfer learning setup is considered. The experimental results show that this framework works well for three types of synthetic data sets, as well as an EEG real-world data set.

  11. Investigation of Cross-Linked and Additive Containing Polymer Materials for Membranes with Improved Performance in Pervaporation and Gas Separation

    Directory of Open Access Journals (Sweden)

    Karl Kleinermanns

    2012-10-01

    Full Text Available Pervaporation and gas separation performances of polymer membranes can be improved by crosslinking or addition of metal-organic frameworks (MOFs. Crosslinked copolyimide membranes show higher plasticization resistance and no significant loss in selectivity compared to non-crosslinked membranes when exposed to mixtures of CO2/CH4 or toluene/cyclohexane. Covalently crosslinked membranes reveal better separation performances than ionically crosslinked systems. Covalent interlacing with 3-hydroxypropyldimethylmaleimide as photocrosslinker can be investigated in situ in solution as well as in films, using transient UV/Vis and FTIR spectroscopy. The photocrosslinking yield can be determined from the FTIR-spectra. It is restricted by the stiffness of the copolyimide backbone, which inhibits the photoreaction due to spatial separation of the crosslinker side chains. Mixed-matrix membranes (MMMs with MOFs as additives (fillers have increased permeabilities and often also selectivities compared to the pure polymer. Incorporation of MOFs into polysulfone and Matrimid® polymers for MMMs gives defect-free membranes with performances similar to the best polymer membranes for gas mixtures, such as O2/N2 H2/CH4, CO2/CH4, H2/CO2, CH4/N2 and CO2/N2 (preferentially permeating gas is named first. The MOF porosity, its particle size and content in the MMM are factors to influence the permeability and the separation performance of the membranes.

  12. Investigation of cross-linked and additive containing polymer materials for membranes with improved performance in pervaporation and gas separation.

    Science.gov (United States)

    Hunger, Katharina; Schmeling, Nadine; Jeazet, Harold B Tanh; Janiak, Christoph; Staudt, Claudia; Kleinermanns, Karl

    2012-10-22

    Pervaporation and gas separation performances of polymer membranes can be improved by crosslinking or addition of metal-organic frameworks (MOFs). Crosslinked copolyimide membranes show higher plasticization resistance and no significant loss in selectivity compared to non-crosslinked membranes when exposed to mixtures of CO2/CH4 or toluene/cyclohexane. Covalently crosslinked membranes reveal better separation performances than ionically crosslinked systems. Covalent interlacing with 3-hydroxypropyldimethylmaleimide as photocrosslinker can be investigated in situ in solution as well as in films, using transient UV/Vis and FTIR spectroscopy. The photocrosslinking yield can be determined from the FTIR-spectra. It is restricted by the stiffness of the copolyimide backbone, which inhibits the photoreaction due to spatial separation of the crosslinker side chains. Mixed-matrix membranes (MMMs) with MOFs as additives (fillers) have increased permeabilities and often also selectivities compared to the pure polymer. Incorporation of MOFs into polysulfone and Matrimid® polymers for MMMs gives defect-free membranes with performances similar to the best polymer membranes for gas mixtures, such as O2/N2 H2/CH4, CO2/CH4, H2/CO2, CH4/N2 and CO2/N2 (preferentially permeating gas is named first). The MOF porosity, its particle size and content in the MMM are factors to influence the permeability and the separation performance of the membranes.

  13. Triptycene dimethyl-bridgehead dianhydride-based intrinsically microporous hydroxyl-functionalized polyimide for natural gas upgrading

    KAUST Repository

    Alghunaimi, Fahd

    2016-07-28

    The synthesis and gas permeation properties of a high-performance hydroxyl-functionalized PIM-polyimide (TDA1-APAF) prepared from a novel 9,10-dimethyl-2,3,6,7-triptycene tetracarboxylic dianhydride (TDA1) and a commercially available 2,2-bis(3-amino-4-hydroxyphenyl)-hexafluoropropane (APAF) diamine monomer are reported. The microporous polymer had a BET surface area based on nitrogen adsorption of 260 m2 g−1. A freshly prepared sample exhibited excellent gas permeation properties: (i) CO2 permeability of 40 Barrer coupled with a CO2/CH4 selectivity of 55 and (ii) H2 permeability of 94 Barrer with a H2/CH4 selectivity of 129. Physical aging over 250 days resulted in significantly enhanced CO2/CH4 and H2/CH4 selectivities of 75 and 183, respectively with only ~ 25% loss in CO2 and H2 permeability. Aged TDA1-APAF exhibited 5-fold higher pure-gas CO2 permeability (30 Barrer) and two-fold higher CO2/CH4 permselectivity over conventional dense cellulose triacetate membranes at 2 bar. In addition, TDA1-APAF polyimide had a N2/CH4 selectivity of 2.3, thereby making it potentially possible to bring natural gas with low, but unacceptable nitrogen content to pipeline specification. Gas mixture permeation experiments with a 1:1 CO2/CH4 feed mixture demonstrated higher mixed- than pure-gas selectivity and plasticization resistance up to 30 bar. These results suggest that intrinsically microporous hydroxyl-functionalized triptycene-based polyimides are promising candidate membrane materials for removal of CO2 from natural gas and hydrogen purification in petrochemical refinery applications.

  14. Mixtures of skewed Kalman filters

    KAUST Repository

    Kim, Hyoungmoon

    2014-01-01

    Normal state-space models are prevalent, but to increase the applicability of the Kalman filter, we propose mixtures of skewed, and extended skewed, Kalman filters. To do so, the closed skew-normal distribution is extended to a scale mixture class of closed skew-normal distributions. Some basic properties are derived and a class of closed skew. t distributions is obtained. Our suggested family of distributions is skewed and has heavy tails too, so it is appropriate for robust analysis. Our proposed special sequential Monte Carlo methods use a random mixture of the closed skew-normal distributions to approximate a target distribution. Hence it is possible to handle skewed and heavy tailed data simultaneously. These methods are illustrated with numerical experiments. © 2013 Elsevier Inc.

  15. Preparation of conducting solid mixtures

    International Nuclear Information System (INIS)

    Spokas, J.J.

    1978-01-01

    The application of conducting plastic mixtures to the fundamental problem of radiation dosimetry is briefly reviewed. A particular approach to achieving formulations with the necessary characteristics is described. A number of successful mixtures are defined for a number of different specific dosimetry situations. To obtain high quality stable materials requires intense blending and working of the materials at elevated temperatures. One machine that succeeds in this task is the Shonka plastics mixer-extruder. The Shonka mixer is described in complete detail. The procedures used in preparing representative formulations with this device are presented. A number of properties of successful conducting mixtures so prepared are summarized. The conditions required for molding such material are given. Several special welding methods for specific application with these formulations have been devised and are described

  16. Bayesian Kernel Mixtures for Counts.

    Science.gov (United States)

    Canale, Antonio; Dunson, David B

    2011-12-01

    Although Bayesian nonparametric mixture models for continuous data are well developed, there is a limited literature on related approaches for count data. A common strategy is to use a mixture of Poissons, which unfortunately is quite restrictive in not accounting for distributions having variance less than the mean. Other approaches include mixing multinomials, which requires finite support, and using a Dirichlet process prior with a Poisson base measure, which does not allow smooth deviations from the Poisson. As a broad class of alternative models, we propose to use nonparametric mixtures of rounded continuous kernels. An efficient Gibbs sampler is developed for posterior computation, and a simulation study is performed to assess performance. Focusing on the rounded Gaussian case, we generalize the modeling framework to account for multivariate count data, joint modeling with continuous and categorical variables, and other complications. The methods are illustrated through applications to a developmental toxicity study and marketing data. This article has supplementary material online.

  17. Toxicology of Chemical Mixtures: A Review of Mixtures Assessment

    National Research Council Canada - National Science Library

    Bjarnason, Stephen

    2004-01-01

    .... Recent advances in disciplines such as genomics, proteomics, metabonomics and physiologically-based pharmacokinetic modeling should assist in the hazard assessment of complex chemical mixtures. However, the process of regulatory assessment of these types of exposures will remain both complex and difficult.

  18. Thermal mixtures in stochastic mechanics

    Energy Technology Data Exchange (ETDEWEB)

    Guerra, F [Rome Univ. (Italy). Ist. di Matematica; Loffredo, M I [Salerno Univ. (Italy). Ist. di Fisica

    1981-01-17

    Stochastic mechanics is extended to systems in thermal equilibrium. The resulting stochastic processes are mixtures of Nelson processes. Their Markov property is investigated in some simple cases. It is found that in order to inforce Markov property the algebra of observable associated to the present must be suitably enlarged.

  19. Characterization of bioactive mixtures oligogalacturonidos

    International Nuclear Information System (INIS)

    Mederos Torres, Yuliem; Hormaza Montenegro, Josefa; Reynaldo Escobar, Ines; Montesino Sequi, Raquel

    2011-01-01

    Oligogalacturonides are pectic oligosaccharides composed of lineal chains of D-galacturonic acid, linked by α (1-4) glycosidic linkage. Oligogalacturonides' mixtures are obtained by enzymatic hydrolysis of pectins of diverse vegetal species. These oligosaccharides unchain a diverse biological activity in plants, which depends mainly on their polymerization degrees. The National Institute of Agricultural Science has a patent technology at national scale that lets to obtain a mixture of oligogalacturonides with different polymerization degree. In this work is presented the characterization of oligogalacturonides by spectrophotometric analysis attending to their uronic acids, reductor sugars, and neutral sugars content. Also the chromatographic profile of samples in study is obtained, using the derivatization with 2-aminobenzamide label and the separation by high pH anion exchange chromatography. It is achieved the separation of at least eight galacturonic acid oligomers with a variable degree of polymerization. On the other hand, the analysis by Fourier transform-infrared spectroscopy (FT-IR) showed that mixtures were composed by galacturonic acid salts. Results indicated that starting from two pectic acids with different characteristics, mixtures of oligogalacturonides of similar chemical composition could be obtained, but they differ in the proportion that they are presented

  20. Ecological Assembly of Chemical Mixtures

    Science.gov (United States)

    Human-environment interactions have a significant role in the formation of chemical mixtures in the environment and by extension in human tissues and fluids. These interactions, which include decisions to purchase and use products containing chemicals as well as behaviors and act...

  1. Etude de l'impact de la variation de la température sur les activités ...

    African Journals Online (AJOL)

    Etude de l'impact de la variation de la température sur les activités microbiennes : application à une population de Listeria monocytogenes CIP 7831, Listeria monocytogenes Scott A CIP 103575 et Escherichia coli ATCC 25922.

  2. Bio-metric study of pig karyotype; Etude biometrique du caryotype du porc

    Energy Technology Data Exchange (ETDEWEB)

    Haag, J; Lacourly, N; Nizza, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-07-01

    This study has a twofold purpose, the former is to determine the swine karyotype as accurately as possible, the latter is to try and develop a method of automatic classification and to show its possibilities and limits. (authors) [French] Cette etude a un double objet: d'une part, de definir de la facon aussi precise que possible le caryotype du porc et d'autre part, de tenter une methode de classification automatique et d'en montrer les possibilites ainsi que les limites. (auteurs)

  3. A Highly Stable Microporous Covalent Imine Network Adsorbent for Natural Gas Upgrading and Flue Gas CO2 Capture

    KAUST Repository

    Das, Swapan Kumar

    2016-06-06

    The feasible capture and separation of CO2 and N2 from CH4 is an important task for natural gas upgrading and the control of greenhouse gas emissions. Here, we studied the microporous covalent imine networks (CIN) material prepared through Schiff base condensation and exhibited superior chemical robustness under both acidic and basic conditions and high thermal stability. The material possesses a relatively uniform nanoparticle size of approximately 70 to 100 nm. This network featured permanent porosity with a high surface area (722 m2g-1) and micropores. A single-component gas adsorption study showed enhanced CO2 and CH4 uptakes of 3.32 mmol/g and 1.14 mmol/g, respectively, at 273 K and 1 bar, coupled with high separation selectivities for CO2/CH4, CH4/N2, and CO2/N2 of 23, 11.8 and 211, respectively. The enriched Lewis basicity in the porous skeletons favours the interaction of quadrupolar CO2 and polarizable CH4, resulting in enhanced CH4 and CO2 uptake and high CH4/N2, CO2/CH4 and CO2/N2 selectivities. Breakthrough experiments showed high CO2/CH4, CH4/N2 and CO2/N2 selectivities of 7.29, 40 and 125, respectively, at 298 K and 1 bar. High heats of adsorption for CH4 and CO2 (QstCH4; 32.61 kJ mol-1 and QstCO2; 42.42 kJ mol-1) provide the ultimate validation for the high selectivity. To the best of our knowledge, such a versatile adsorbent material that displays both enhanced uptake and selectivity for a variety of binary gas mixtures, including CO2/ CH4, CO2/N2 and CH4/N2, has not been extensively explored.

  4. Synthesis and gas transport properties of hydroxyl-functionalized polyimides with intrinsic microporosity

    KAUST Repository

    Ma, Xiaohua

    2012-05-08

    A newly designed diamine monomer, 3,3,3′,3′-tetramethyl-1, 1′-spirobisindane-5,5′-diamino-6,6′-diol, was successfully used to synthesize two types of polyimides for membrane-based gas separation applications. The novel polymers integrate significant microporosity and polar hydroxyl groups, showing the combined features of polymers of intrinsic microporosity (PIMs) and functional polyimides (PIs). They possess high thermal stability, good solubility, and easy processability for membrane fabrication; the resulting membranes exhibit good permeability owing to the intrinsic microporosity introduced by the highly contorted PIM segments as well as high CO 2/CH 4 selectivity that arises from the hydroxyl groups. The membranes show CO 2/CH 4 selectivities of >20 when tested with a 1:1 CO 2/CH 4 mixture for feed pressures up to 50 bar. In addition, the incorporation of hydroxyl groups and microporosity in the polymers enhances their affinity to water, leading to remarkable water sorption capacities of up to 22 wt % at 35 °C and 95% relative humidity. © 2012 American Chemical Society.

  5. Hydroquinone and Quinone-Grafted Porous Carbons for Highly Selective CO2 Capture from Flue Gases and Natural Gas Upgrading.

    Science.gov (United States)

    Wang, Jun; Krishna, Rajamani; Yang, Jiangfeng; Deng, Shuguang

    2015-08-04

    Hydroquinone and quinone functional groups were grafted onto a hierarchical porous carbon framework via the Friedel-Crafts reaction to develop more efficient adsorbents for the selective capture and removal of carbon dioxide from flue gases and natural gas. The oxygen-doped porous carbons were characterized with scanning electron microscopy, transmission electron microscopy, X-ray powder diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopy. CO2, CH4, and N2 adsorption isotherms were measured and correlated with the Langmuir model. An ideal adsorbed solution theory (IAST) selectivity for the CO2/N2 separation of 26.5 (298 K, 1 atm) was obtained on the hydroquinone-grafted carbon, which is 58.7% higher than that of the pristine porous carbon, and a CO2/CH4 selectivity value of 4.6 (298 K, 1 atm) was obtained on the quinone-grafted carbon (OAC-2), which represents a 28.4% improvement over the pristine porous carbon. The highest CO2 adsorption capacity on the oxygen-doped carbon adsorbents is 3.46 mmol g(-1) at 298 K and 1 atm. In addition, transient breakthrough simulations for CO2/CH4/N2 mixture separation were conducted to demonstrate the good separation performance of the oxygen-doped carbons in fixed bed adsorbers. Combining excellent adsorption separation properties and low heats of adsorption, the oxygen-doped carbons developed in this work appear to be very promising for flue gas treatment and natural gas upgrading.

  6. Mixtures in nonstable Levy processes

    International Nuclear Information System (INIS)

    Petroni, N Cufaro

    2007-01-01

    We analyse the Levy processes produced by means of two interconnected classes of nonstable, infinitely divisible distribution: the variance gamma and the Student laws. While the variance gamma family is closed under convolution, the Student one is not: this makes its time evolution more complicated. We prove that-at least for one particular type of Student processes suggested by recent empirical results, and for integral times-the distribution of the process is a mixture of other types of Student distributions, randomized by means of a new probability distribution. The mixture is such that along the time the asymptotic behaviour of the probability density functions always coincide with that of the generating Student law. We put forward the conjecture that this can be a general feature of the Student processes. We finally analyse the Ornstein-Uhlenbeck process driven by our Levy noises and show a few simulations of it

  7. The formation of scientists and technicians at the 'Centre d'Etudes Nucleaires' at Saclay

    International Nuclear Information System (INIS)

    Debiesse, J.

    1958-01-01

    The considerable needs in research workers and scientists which are asked by the nuclear energy obliged the Commissariat a l'Energie atomique to deal with a particular effort to increase the quantitative and qualitative formation of scientists. Most various ways have been used. 1- A National Institute of Nuclear Sciences and Nuclear Techniques was created, by a joint decree of the Prime Minister and the Minister for National Education (june 18, 1957). This Institute of Higher Teaching (250 students) indulges in the following matters: atomic engineering, quantum mechanics, theory and technic of particle accelerators, special metallurgy, radiobiology, thermic and mechanics of fluids. 2- An associated centre of the 'Conservatoire National des Arts et Metiers' was created (200 students) for technical assistants, drawers, etc. 3- In contribution with both electronic industry and Ministry of Work, the Centre d'Etudes Nucleaires contributes to an accelerated formation of technical assistants into Professional Centres. Conclusion: Training of scientists and research workers is one of the most important activities of the Centre d'Etudes Nucleaires de Saclay. Without losing its technical efficiency, it has supplied and varied means adapted to the various purposes that we shall reach. (author) [fr

  8. Consistency of the MLE under mixture models

    OpenAIRE

    Chen, Jiahua

    2016-01-01

    The large-sample properties of likelihood-based statistical inference under mixture models have received much attention from statisticians. Although the consistency of the nonparametric MLE is regarded as a standard conclusion, many researchers ignore the precise conditions required on the mixture model. An incorrect claim of consistency can lead to false conclusions even if the mixture model under investigation seems well behaved. Under a finite normal mixture model, for instance, the consis...

  9. Dirichlet Process Parsimonious Mixtures for clustering

    OpenAIRE

    Chamroukhi, Faicel; Bartcus, Marius; Glotin, Hervé

    2015-01-01

    The parsimonious Gaussian mixture models, which exploit an eigenvalue decomposition of the group covariance matrices of the Gaussian mixture, have shown their success in particular in cluster analysis. Their estimation is in general performed by maximum likelihood estimation and has also been considered from a parametric Bayesian prospective. We propose new Dirichlet Process Parsimonious mixtures (DPPM) which represent a Bayesian nonparametric formulation of these parsimonious Gaussian mixtur...

  10. Some properties of explosive mixtures containing peroxides

    International Nuclear Information System (INIS)

    Zeman, Svatopluk; Trzcinski, Waldemar A.; Matyas, Robert

    2008-01-01

    This study concerns mixtures of triacetone triperoxide (3,3,6,6,9,9-hexamethyl-1,2,4,5,7,8-hexoxonane, TATP) and ammonium nitrate (AN) with added water (W), as the case may be, and dry mixtures of TATP with urea nitrate (UN). Relative performances (RP) of the mixtures and their individual components, relative to TNT, were determined by means of ballistic mortar. The detonation energies, E 0 , and detonation velocities, D, were calculated for the mixtures studied by means of the thermodynamic code CHEETAH. Relationships have been found and are discussed between the RP and the E 0 values related to unit volume of gaseous products of detonation of these mixtures. These relationships together with those between RP and oxygen balance values of the mixtures studied indicate different types of participation of AN and UN in the explosive decomposition of the respective mixtures. Dry TATP/UN mixtures exhibit lower RP than analogous mixtures TATP/AN containing up to 25% of water. Depending on the water content, the TATP/AN mixtures possess higher detonability values than the ANFO explosives. A semi-logarithmic relationship between the D values and oxygen coefficients has been derived for all the mixtures studied at the charge density of 1000 kg m -3 . Among the mixtures studied, this relationship distinguishes several samples of the type of 'tertiary explosives' as well as samples that approach 'high explosives' in their performances and detonation velocities

  11. TRANSPORT PROPERTIES FOR REFRIGERANT MIXTURES

    Directory of Open Access Journals (Sweden)

    V. Geller

    2014-06-01

    Full Text Available A set of models to predict viscosity and thermal conductivity of refrigerant mixtures is developed. A general model for viscosity and thermal conductivity use the three contributions sum form (the dilute-gas terms, the residual terms, and the liquid terms. The corresponding states model is recommended to predict the dense gas transport properties over a range of reduced density from 0 to 2. It is shown that the RHS model provides the most reliable results for the saturated-liquid and the compressed-liquid transport properties over a range of given temperatures from 0,5 to 0,95.

  12. Nonparametric Mixture of Regression Models.

    Science.gov (United States)

    Huang, Mian; Li, Runze; Wang, Shaoli

    2013-07-01

    Motivated by an analysis of US house price index data, we propose nonparametric finite mixture of regression models. We study the identifiability issue of the proposed models, and develop an estimation procedure by employing kernel regression. We further systematically study the sampling properties of the proposed estimators, and establish their asymptotic normality. A modified EM algorithm is proposed to carry out the estimation procedure. We show that our algorithm preserves the ascent property of the EM algorithm in an asymptotic sense. Monte Carlo simulations are conducted to examine the finite sample performance of the proposed estimation procedure. An empirical analysis of the US house price index data is illustrated for the proposed methodology.

  13. A database for CO2 Separation Performances of MOFs based on Computational Materials Screening.

    Science.gov (United States)

    Altintas, Cigdem; Avci, Gokay; Daglar, Hilal; Nemati Vesali Azar, Ayda; Velioglu, Sadiye; Erucar, Ilknur; Keskin, Seda

    2018-05-03

    Metal organic frameworks (MOFs) have been considered as great candidates for CO2 capture. Considering the very large number of available MOFs, high-throughput computational screening plays a critical role in identifying the top performing materials for target applications in a time-effective manner. In this work, we used molecular simulations to screen the most recent and complete MOF database for identifying the most promising materials for CO2 separation from flue gas (CO2/N2) and landfill gas (CO2/CH4) under realistic operating conditions. We first validated our approach by comparing the results of our molecular simulations for the CO2 uptakes, CO2/N2 and CO2/CH4 selectivities of various types of MOFs with the available experimental data. We then computed binary CO2/N2 and CO2/CH4 mixture adsorption data for the entire MOF database and used these results to calculate several adsorbent selection metrics such as selectivity, working capacity, adsorbent performance score, regenerability, and separation potential. MOFs were ranked based on the combination of these metrics and the top performing MOF adsorbents that can achieve CO2/N2 and CO2/CH4 separations with high performance were identified. Molecular simulations for the adsorption of a ternary CO2/N2/CH4 mixture were performed for these top materials in order to provide a more realistic performance assessment of MOF adsorbents. Structure-performance analysis showed that MOFs with ΔQ>30 kJ/mol, 3.8 A≤PLD≤5 A, 5 A≤LCD≤7.5 A, 0.5≤ϕ≤0.75, SA≤1,000 m2/g, ρ>1 g/cm 3 are the best candidates for selective separation of CO2 from flue gas and landfill gas. This information will be very useful to design novel MOFs with the desired structural features that can lead to high CO2 separation potentials. Finally, an online, freely accessible database https://cosmoserc.ku.edu.tr was established, for the first time in the literature, which reports all computed adsorbent metrics of 3,816 MOFs for CO2/N2, CO2/CH4

  14. GRAVITY PIPELINE TRANSPORT FOR HARDENING FILLING MIXTURES

    Directory of Open Access Journals (Sweden)

    Leonid KROUPNIK

    2015-12-01

    Full Text Available In underground mining of solid minerals becoming increasingly common development system with stowing hardening mixtures. In this case the natural ore array after it is replaced by an artificial excavation of solidified filling mixture consisting of binder, aggregates and water. Such a mixture is prepared on the surface on special stowing complexes and transported underground at special stowing pipelines. However, it is transported to the horizons of a few kilometers, which requires a sustainable mode of motion of such a mixture in the pipeline. Hardening stowing mixture changes its rheological characteristics over time, which complicates the calculation of the parameters of pipeline transportation. The article suggests a method of determining the initial parameters of such mixtures: the status coefficient, indicator of transportability, coefficient of hydrodynamic resistance to motion of the mixture. These indicators characterize the mixture in terms of the possibility to transport it through pipes. On the basis of these indicators is proposed methodology for calculating the parameters of pipeline transport hardening filling mixtures in drift mode when traffic on the horizontal part of the mixture under pressure column of the mixture in the vertical part of the backfill of the pipeline. This technique allows stable operation is guaranteed to provide pipeline transportation.

  15. Vibrational relaxation in OCS mixtures

    International Nuclear Information System (INIS)

    Simpson, C.J.S.M.; Gait, P.D.; Simmie, J.M.

    1976-01-01

    Experimental measurements are reported of vibrational relaxation times which may be used to show whether there is near resonant vibration-rotation energy transfer between OCS and H 2 , D 2 or HD. Vibrational relaxation times have been measured in OCS and OCS mixtures over the temperature range 360 to 1000 K using a shock tube and a laser schlieren system. The effectiveness of the additives in reducing the relaxation time of OCS is in the order 4 He 3 He 2 2 and HD. Along this series the effect of an increase in temperature changes from the case of speeding up the rate with 4 He to retarding it with D 2 , HD and H 2 . There is no measurable difference in the effectiveness of n-D 2 and o-D 2 and little, or no, difference between n-H 2 and p-H 2 . Thus the experimental results do not give clear evidence for rotational-vibration energy transfer between hydrogen and OCS. This contrasts with the situation for CO 2 + H 2 mixtures. (author)

  16. Supercritical Water Mixture (SCWM) Experiment

    Science.gov (United States)

    Hicks, Michael C.; Hegde, Uday G.

    2012-01-01

    The subject presentation, entitled, Supercritical Water Mixture (SCWM) Experiment, was presented at the International Space Station (ISS) Increment 33/34 Science Symposium. This presentation provides an overview of an international collaboration between NASA and CNES to study the behavior of a dilute aqueous solution of Na2SO4 (5% w) at near-critical conditions. The Supercritical Water Mixture (SCWM) investigation, serves as important precursor work for subsequent Supercritical Water Oxidation (SCWO) experiments. The SCWM investigation will be performed in DECLICs High Temperature Insert (HTI) for the purpose of studying critical fluid phenomena at high temperatures and pressures. The HTI includes a completely sealed and integrated test cell (i.e., Sample Cell Unit SCU) that will contain approximately 0.3 ml of the aqueous test solution. During the sequence of tests, scheduled to be performed in FY13, temperatures and pressures will be elevated to critical conditions (i.e., Tc = 374C and Pc = 22 MPa) in order to observe salt precipitation, precipitate agglomeration and precipitate transport in the presence of a temperature gradient without the influences of gravitational forces. This presentation provides an overview of the motivation for this work, a description of the DECLIC HTI hardware, the proposed test sequences, and a brief discussion of the scientific research objectives.

  17. Stable isotope separation; Separations physicochimiques d'isotopes stables realisations et etudes de petites productions

    Energy Technology Data Exchange (ETDEWEB)

    Botter, F; Molinari, Ph; Dirian, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Pure deuterium has been separated from gaseous mixtures of hydrogen and deuterium by band displacement chromatography, using columns of palladium on a support. The best results were obtained with columns of Pd on sintered {alpha} alumina. With a column of this type, of total capacity about 2 liters, a preparative apparatus of low dead volume has been built which produces 1 liter of pure D{sub 2} from a 50 p. 100 D{sub 2}, 50 p. 100 100 H{sub 2} mixture in about 12 minutes. As a first approximation chromatography is likened theoretically to counter current fractionation, neglecting superficial resistance to the exchange. and also longitudinal diffusions. The number of theoretical plates required necessary for a certain enrichment of the gas phase is determined graphically or by calculation, enabling comparisons to be made between the efficiencies of columns containing different amounts of palladium. Thermal Diffusion: For the separation of hydrogen isotopes a thermal diffusion installation, made of stainless steel and entirely tele-commanded has been constructed. The separation cascade is made up of two identical pairs of hot wire columns. Each pair can work separately or they may be connected by a thermosyphon. The temperature of the hot wire is kept at around 1000 deg C by direct current. With this installation, hydrogen samples with a deuterium content lower than o,5 ppm were obtained from a gas originally containing 32 ppm. It was thus possible to prepare tritium of 99,3 p. 100 concentration from gas with an initial content of 6 p. 100. For quantitative separation of xenon enriched five time in {sup 124}Xe by thermal diffusion, two identical cascades were constructed, each consisting of 5 columns, working in parallel and the two being connected by thermosyphon or by a capillary tube linked to a thermal gas oscillation. The central tungsten wire is heated to 1200 deg C. The columns are grouped like cluster of a heat exchanger, in shell of 30 cm diameter through

  18. Generalities on the dynamic behaviour of rapid reactors. Preliminary studies on Rapsodie; Generalites sur le comportement dynamique des piles rapides. Etudes preliminaires de rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Campan, J L; Chaumont, J P; Clauzon, P P; Ghesquiere, G; Leduc, J; Schmitt, A P; Zaleski, C P [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1963-07-01

    The study of the dynamic behaviour of fast reactors may be divided into three section: 1. Stability studies around equilibrium power only the linear case was examining. S. Transient studies in the case of usual reactor operation (shut down, scram, etc.) with thermal shocks evaluation, for instance. 3. Explosion studies, for the maximum credible accidents. This report presents the status of the studies performed at the 'Physics Research Department' at Cadarache. Methods used are detailed and illustrated with the results obtained on a preliminary metallic core of the Rapsodie Reactor. (authors) [French] Le comportement dynamique des piles rapides, se presente tout naturellement sous trois aspects: 1. Etude de stabilite autour d'un regime d'equilibre (nous nous sommes bornes ici au cas lineaire). 2. Etude de regimes transitoires lors des operations normales de pile (arret, arret d'urgence, etc.) avec evaluation des chocs thermiques par exemple. 3. Etude des regimes transitoires de caractere explosif lors des accidents les plus graves possibles. Ce rapport presente l'etat des etudes a la date du 20 decembre 1961 a la Section d'Etudes de Piles Rapides a CADARACHE. Les methodes employees ont ete detaillees et illustrees a partir des resultats obtenus sur une premiere version 'combustible metallique' de Rapsodie. (auteurs)

  19. Etude cinétique de la dégradation de l'Endosufane en solution ...

    African Journals Online (AJOL)

    Etude cinétique de la dégradation de l'Endosufane en solution. S Traore, K Mamadou, A Dembele, V Yao, Y Bekro, P Mazellier, B Legube, P Houenou. Abstract. Les pesticides sont fréquemment utilisés en Côte d'Ivoire. Leur détection dans les eaux de forage témoigne de leur mauvais usage et d'un grave problème ...

  20. An economic study of the site of Marcoule; Etude economique du site de Marcoule

    Energy Technology Data Exchange (ETDEWEB)

    Duprat, H [Commissariat a l' Energie Atomique, Marcoule (France). Centre d' Etudes Nucleaires

    1964-07-01

    The study of this site of the Marcoule Center shows that its regional economical influence is limited to the buying power distributed among its personnel. This entails distortions between first this supplementary buying power and the overall markets within the possible Marcoule influence zone, and secondly the concentration on Bagnols-sur-Ceze and this town's normal extension possibilities. (author) [French] L'etude du site de Marcoule demontre que son influence economique se limite, pour la region, au pouvoir d'achat distribue a son personnel. Ceci entraine une disproportion d'une part entre ce pouvoir d'achat supplementaire et l'ensemble des marches contenus dans l'aire d'influence possible de Marcoule, d'autre part entre la concentration realisee a Bagnole-sur-Ceze et la capacite d'extension normale de cette agglomeration. (auteur)

  1. Neutronic study of the two french heavy water reactors; Etude neutronique des deux piles francaises a eau lourde

    Energy Technology Data Exchange (ETDEWEB)

    Horowitz, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    The two french reactors - the reactor of Chatillon, named Zoe, and the reactor of Saclay - P2 - were the object of detailed neutronic studies which the main ideas are exposed in this report. These studies were mostly done by the Department of the Reactor Studies (D.E.P.). We have thus studied the distribution of neutronic fluxes; the factors influencing reactivity; the link between reactivity and divergence with the formula of Nordheim; the mean time life of neutrons; neutron spectra s of P2; the xenon effect; or the effect of the different adjustments of the plates and controls bar. (M.B.) [French] Les deux reacteurs francais - la pile de Chatillon, appelee ZOE, et la pile de Saclay, designee dans la suite par P2 - ont fait l'objet d'etudes neutroniques detaillees dont les principales sont exposees dans ce rapport. Ces etudes ont ete pour la plupart effectuees dans le cadre du Departement des Etudes de Piles (D.E.P.). Nous avons ainsi entre autre etudie la distribution du flux neutronique; les facteurs influencants la reactivite; le lien entre reactivite et divergence par la formule de Nordheim; le temps de vie moyen des neutrons; les spectres de neutrons de P2; l'effet xenon; ou encore l'effet des differents reglages des plaques et barres de controles. (M.B.)

  2. Mixtures and their risk assessment in toxicology.

    Science.gov (United States)

    Mumtaz, Moiz M; Hansen, Hugh; Pohl, Hana R

    2011-01-01

    For communities generally and for persons living in the vicinity of waste sites specifically, potential exposures to chemical mixtures are genuine concerns. Such concerns often arise from perceptions of a site's higher than anticipated toxicity due to synergistic interactions among chemicals. This chapter outlines some historical approaches to mixtures risk assessment. It also outlines ATSDR's current approach to toxicity risk assessment. The ATSDR's joint toxicity assessment guidance for chemical mixtures addresses interactions among components of chemical mixtures. The guidance recommends a series of steps that include simple calculations for a systematic analysis of data leading to conclusions regarding any hazards chemical mixtures might pose. These conclusions can, in turn, lead to recommendations such as targeted research to fill data gaps, development of new methods using current science, and health education to raise awareness of residents and health care providers. The chapter also provides examples of future trends in chemical mixtures assessment.

  3. Efficient radiative transfer in dust grain mixtures

    OpenAIRE

    Wolf, S.

    2002-01-01

    The influence of a dust grain mixture consisting of spherical dust grains with different radii and/or chemical composition on the resulting temperature structure and spectral energy distribution of a circumstellar shell is investigated. The comparison with the results based on an approximation of dust grain parameters representing the mean optical properties of the corresponding dust grain mixture reveal that (1) the temperature dispersion of a real dust grain mixture decreases substantially ...

  4. Some properties of explosive mixtures containing peroxides

    Energy Technology Data Exchange (ETDEWEB)

    Zeman, Svatopluk [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, CZ-532 10 Pardubice (Czech Republic)], E-mail: svatopluk.zeman@upce.cz; Trzcinski, Waldemar A. [Institute of Chemistry, Military University of Technology, PL-00-908 Warsaw 49 (Poland); Matyas, Robert [Institute of Energetic Materials, Faculty of Chemical Technology, University of Pardubice, CZ-532 10 Pardubice (Czech Republic)

    2008-06-15

    This study concerns mixtures of triacetone triperoxide (3,3,6,6,9,9-hexamethyl-1,2,4,5,7,8-hexoxonane, TATP) and ammonium nitrate (AN) with added water (W), as the case may be, and dry mixtures of TATP with urea nitrate (UN). Relative performances (RP) of the mixtures and their individual components, relative to TNT, were determined by means of ballistic mortar. The detonation energies, E{sub 0}, and detonation velocities, D, were calculated for the mixtures studied by means of the thermodynamic code CHEETAH. Relationships have been found and are discussed between the RP and the E{sub 0} values related to unit volume of gaseous products of detonation of these mixtures. These relationships together with those between RP and oxygen balance values of the mixtures studied indicate different types of participation of AN and UN in the explosive decomposition of the respective mixtures. Dry TATP/UN mixtures exhibit lower RP than analogous mixtures TATP/AN containing up to 25% of water. Depending on the water content, the TATP/AN mixtures possess higher detonability values than the ANFO explosives. A semi-logarithmic relationship between the D values and oxygen coefficients has been derived for all the mixtures studied at the charge density of 1000 kg m{sup -3}. Among the mixtures studied, this relationship distinguishes several samples of the type of 'tertiary explosives' as well as samples that approach 'high explosives' in their performances and detonation velocities.

  5. Method for separating gaseous mixtures of isotopes

    International Nuclear Information System (INIS)

    Neimann, H.J.; Schuster, E.; Kersting, A.

    1976-01-01

    A gaseous mixture of isotopes is separated by laser excitation of the isotope mixture with a narrow band of wavelengths, molecularly exciting mainly the isotope to be separated and thereby promoting its reaction with its chemical partner which is excited in a separate chamber. The excited isotopes and the chemical partner are mixed, perhaps in a reaction chamber to which the two excited components are conducted by very short conduits. The improvement of this method is the physical separation of the isotope mixture and its partner during excitation. The reaction between HCl and the mixture of 238 UF 6 and 235 UF 6 is discussed

  6. Shear viscosity of liquid mixtures: Mass dependence

    International Nuclear Information System (INIS)

    Kaushal, Rohan; Tankeshwar, K.

    2002-06-01

    Expressions for zeroth, second, and fourth sum rules of transverse stress autocorrelation function of two component fluid have been derived. These sum rules and Mori's memory function formalism have been used to study shear viscosity of Ar-Kr and isotopic mixtures. It has been found that theoretical result is in good agreement with the computer simulation result for the Ar-Kr mixture. The mass dependence of shear viscosity for different mole fraction shows that deviation from ideal linear model comes even from mass difference in two species of fluid mixture. At higher mass ratio shear viscosity of mixture is not explained by any of the emperical model. (author)

  7. Evaluation of mastic in bituminous mixtures

    OpenAIRE

    Silva, Hugo Manuel Ribeiro Dias da; Pais, Jorge C.; Pereira, Paulo A. A.

    2002-01-01

    The efficiency of the asphalt-aggregate bond is one of the key factors which affects the mechanical resistance of bituminous mixtures and a better understanding of its performance allows the behaviour of mixture to be more accurately predicted. The asphalt-aggregate bond depends on the properties of the mastic and the mixture of fine aggregate and bitumen which bonds itself to the larger sized particles within the bituminous mixture. This mastic plays an im-portant role in the asphalt-aggr...

  8. Shear viscosity of liquid mixtures Mass dependence

    CERN Document Server

    Kaushal, R

    2002-01-01

    Expressions for zeroth, second, and fourth sum rules of transverse stress autocorrelation function of two component fluid have been derived. These sum rules and Mori's memory function formalism have been used to study shear viscosity of Ar-Kr and isotopic mixtures. It has been found that theoretical result is in good agreement with the computer simulation result for the Ar-Kr mixture. The mass dependence of shear viscosity for different mole fraction shows that deviation from ideal linear model comes even from mass difference in two species of fluid mixture. At higher mass ratio shear viscosity of mixture is not explained by any of the emperical model.

  9. Contribution to the study of uranyl salts in butyl phosphate solutions; Contribution a l'etude des solutions de sels d'uranyle dans les phosphates butyliques

    Energy Technology Data Exchange (ETDEWEB)

    Coulon, A. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1965-06-01

    A spectroscopic study in the normal infrared region and involving the following associations: tri-alkyl phosphates (tri-butyl, tri-ethyl, tri-methyl), uranyl salts (nitrate, chloride, acetate) has confirmed the existence of an interaction between the phosphoryl group and the uranium atom, as shown by a movement of absorption band for the valency P = 0 from {approx} 1270 cm{sup -1} to {approx} 1180 cm{sup -1}. A study of the preparation, analysis and spectroscopy of the solids obtained by the precipitation of uranyl salts by acid butyl phosphates has been carried out. By infrared spectrophotometry it has been shown that the tri-butyl and di-butyl phosphates are associated in non-polar diluents even before the uranium is introduced. The extraction of uranyl salts from acid aqueous solutions by a diluted mixture of tri-butyl and di-butyl phosphates proceeds by different mechanisms according to the nature of the ion (nitrate or chloride). (author) [French] Une etude spectroscopique dans l'infrarouge moyen portant sur les associations: - phosphates trialcoyliques (tributylique - triethylique - trimethylique) - sels d'uranyle (nitrate, chlorure, acetate) a confirme l'existence d'une interaction entre le groupement phosphoryle et l'atome d'uranium, se manifestant par un deplacement de la bande d'absorption de la vibration de valence P = 0 de {approx} 1270 cm{sup -1} a {approx} 1180 cm{sup -1}. Une etude preparative, analytique et spectroscopique des solides obtenus par precipitation de sels d'uranyle par les phosphates butyliques acides a ete effectuee. La spectrophotomerie infrarouge met en evidence l'association, anterieure a toute introduction d'uranium, des phosphates tributylique et dibutylique dans des diluants non polaires. L'extraction de sels d'uranyle, d'une solution aqueuse acide par un melange dilue de phosphates tributylique et dibutylique, s'effectue suivant des processus differents a la

  10. Deciding which chemical mixtures risk assessment methods work best for what mixtures

    International Nuclear Information System (INIS)

    Teuschler, Linda K.

    2007-01-01

    The most commonly used chemical mixtures risk assessment methods involve simple notions of additivity and toxicological similarity. Newer methods are emerging in response to the complexities of chemical mixture exposures and effects. Factors based on both science and policy drive decisions regarding whether to conduct a chemical mixtures risk assessment and, if so, which methods to employ. Scientific considerations are based on positive evidence of joint toxic action, elevated human exposure conditions or the potential for significant impacts on human health. Policy issues include legislative drivers that may mandate action even though adequate toxicity data on a specific mixture may not be available and risk assessment goals that impact the choice of risk assessment method to obtain the amount of health protection desired. This paper discusses three important concepts used to choose among available approaches for conducting a chemical mixtures risk assessment: (1) additive joint toxic action of mixture components; (2) toxicological interactions of mixture components; and (3) chemical composition of complex mixtures. It is proposed that scientific support for basic assumptions used in chemical mixtures risk assessment should be developed by expert panels, risk assessment methods experts, and laboratory toxicologists. This is imperative to further develop and refine quantitative methods and provide guidance on their appropriate applications. Risk assessors need scientific support for chemical mixtures risk assessment methods in the form of toxicological data on joint toxic action for high priority mixtures, statistical methods for analyzing dose-response for mixtures, and toxicological and statistical criteria for determining sufficient similarity of complex mixtures

  11. Etudes physiques des mélanges eau-cryoprotecteurs

    Science.gov (United States)

    Vassoille, R.; Perez, J.

    The aim of the following review is to present the most important studies concerning the physical properties of water-solutes mixtures used in cryobiology. Cryobiology is a branch of biology which deals with the very low temperature behaviour of cells. This technique is developed today in several directions. The creation of banks of cells and perhaps in a short time of small organs, is the purpose of much research in this domain. Before freezing, living cells are generally put in a solution containing one or more solutes. The role of these solutes is to protect the cells against damage due to crystallization of water (cryoprotectors). The mechanisms of cryoprotection are not well known ; nevertheless the vitreous state formation during cooling is often invoked. So, it is possible to avoid crystallization damage such as mechanical strain (due to an increase of volume of about 10 %) and salt effects (due to osmotic pressure). The conditions in which the vitreous state is obtained, maintained during cooling, storage at low temperature and rewarming can be defined by physical studies presented in the following review. Le présent travail est essentiellement une revue bibliographique des principales études physiques qui ont été réalisées avec des solutions de composés habituellement employés en cryobiologie. La cryobiologie est une branche de la biologie qui s'intéresse au comportement des cellules à basse température. Cette discipline est actuellement en plein développement dans des domaines très divers. Son principal but est la création de banques de cellules de plus en plus complexes avec comme perspective la conservation des organes. Les cellules vivantes sont généralement placées avant congélation dans une solution contenant divers composés dont le rôle est de protéger les cellules contre les effets de la cristallisation de l'eau. L'action protectrice de ces cryoprotecteurs est encore mal connue; cependant, la formation d'un état vitreux lors du

  12. Thermodynamics of mixtures containing amines

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, Juan Antonio [G.E.T.E.F. Dpto Termodinamica y Fisica Aplicada, Facultad de Ciencias, Universidad de Valladolid, Valladolid 47071 (Spain)], E-mail: jagl@termo.uva.es; Mozo, Ismael; Garcia de la Fuente, Isaias; Cobos, Jose Carlos [G.E.T.E.F. Dpto Termodinamica y Fisica Aplicada, Facultad de Ciencias, Universidad de Valladolid, Valladolid 47071 (Spain); Riesco, Nicolas [Department of Chemical Engineering, Loughborough University, Loughborough, LE113TU Leicestershire (United Kingdom)

    2008-01-30

    Mixtures with dimethyl or trimethylpyridines and alkane, aromatic compound or 1-alkanol have been examined using different theories: DISQUAC, Flory, the concentration-concentration structure factor, S{sub CC}(0), or the Kirkwood-Buff formalism. DISQUAC represents fairly well the available experimental data, and improves theoretical calculations from Dortmund UNIFAC. Two important effects have been investigated: (i) the effect of increasing the number of methyl groups attached to the aromatic ring of the amine; (ii) the effect of modifying the position of the methyl groups in this ring. The molar excess enthalpy, H{sup E}, and the molar excess volume, V{sup E}, decrease in systems with alkane or methanol as follows: pyridine > 3-methylpyridine > 3,5-dimethylpyridine and pyridine > 2-methylpyridine > 2,4-dimethylpyridine > 2,4,6-trimethylpyridine, which has been attributed to a weakening of the amine-amine interactions in the same sequences. This is in agreement with the relative variation of the effective dipole moment, {mu}-bar, and of the differences between the boiling temperature of a pyridine base and that of the homomorphic alkane. For heptane solutions, the observed H{sup E} variation, H{sup E} (3,5-dimethylpyridine) > H{sup E} (2,4-dimethylpyridine) > H{sup E} (2,6-dimethylpyridine), is explained similarly. Calculations on the basis of the Flory model confirm that orientational effects become weaker in systems with alkane in the order: pyridine > methylpyridine > dimethylpyridine > trimethylpyridine. S{sub CC}(0) calculations show that steric effects increase with the number of CH{sub 3}- groups in the pyridine base, and that the steric effects exerted by methyl groups in positions 2 and 6 are higher than when they are placed in positions 3 and 5. The hydrogen bond energy in methanol mixtures is independent of the pyridine base, and it is estimated to be -35.2 kJ mol{sup -1}. Heterocoordination in these solutions is due in part to size effects. Their

  13. An oxyde mixture fuel containing uranium and plutonium dioxides and process to obtain this oxyde mixture

    International Nuclear Information System (INIS)

    Hannerz, K.

    1976-01-01

    An oxide-mixture fuel containing uranium and plutonium dioxides having the slage of spherical, or nearly spherical, oxide-mixture particles with a diameter within the range of from 0.2 to 2 mn charactarized in that each oxide-mixture particles is provided with an outer layer comprising mainly UO2, the thickness of which is at least 0.05; whereas the inner portion of the oxide-mixture particles comprises mainly PUO 2

  14. Process Dissociation and Mixture Signal Detection Theory

    Science.gov (United States)

    DeCarlo, Lawrence T.

    2008-01-01

    The process dissociation procedure was developed in an attempt to separate different processes involved in memory tasks. The procedure naturally lends itself to a formulation within a class of mixture signal detection models. The dual process model is shown to be a special case. The mixture signal detection model is applied to data from a widely…

  15. Buffer gas cooling and mixture analysis

    Science.gov (United States)

    Patterson, David S.; Doyle, John M.

    2018-03-06

    An apparatus for spectroscopy of a gas mixture is described. Such an apparatus includes a gas mixing system configured to mix a hot analyte gas that includes at least one analyte species in a gas phase into a cold buffer gas, thereby forming a supersaturated mixture to be provided for spectroscopic analysis.

  16. Unfolding the potential of wheat cultivar mixtures

    DEFF Research Database (Denmark)

    Borg, J.; Kiær, Lars Pødenphant; Lecarpentier, C.

    2018-01-01

    and they are not encouraged by advisory services. Based on the methodology developed by Kiær et al. (2009), we achieved a meta-analysis of cultivar mixtures in wheat. Among the 120 publications dedicated to wheat, we selected 32 studies to analyze various factors that may condition the success or failure of wheat mixtures...

  17. Separation of organic azeotropic mixtures by pervaporation

    Energy Technology Data Exchange (ETDEWEB)

    Baker, R.W.

    1991-12-01

    Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

  18. Fibril assembly in whey protein mixtures

    NARCIS (Netherlands)

    Bolder, S.G.

    2007-01-01

    The objective of this thesis was to study fibril assembly in mixtures of whey proteins. The effect of the composition of the protein mixture on the structures and the resulting phase behaviour was investigated. The current work has shown that beta-lactoglobulin is responsible for the fibril assembly

  19. Process of decomposing an oil mixture

    Energy Technology Data Exchange (ETDEWEB)

    Kubierschky, K

    1917-12-02

    A process is described for the decomposition of oil mixtures, and the like, by means of alcohol, characterized in that the subject mixture is brought into solution in high-grade alcohol, and this solution is washed countercurrent with dilute alcohol.

  20. Mixture Modeling: Applications in Educational Psychology

    Science.gov (United States)

    Harring, Jeffrey R.; Hodis, Flaviu A.

    2016-01-01

    Model-based clustering methods, commonly referred to as finite mixture modeling, have been applied to a wide variety of cross-sectional and longitudinal data to account for heterogeneity in population characteristics. In this article, we elucidate 2 such approaches: growth mixture modeling and latent profile analysis. Both techniques are…

  1. Intelligent gas-mixture flow sensor

    NARCIS (Netherlands)

    Lammerink, Theodorus S.J.; Dijkstra, Fred; Houkes, Z.; van Kuijk, J.C.C.; van Kuijk, Joost

    A simple way to realize a gas-mixture flow sensor is presented. The sensor is capable of measuring two parameters from a gas flow. Both the flow rate and the helium content of a helium-nitrogen gas mixture are measured. The sensor exploits two measurement principles in combination with (local)

  2. Shock formation in mixtures of fluids

    International Nuclear Information System (INIS)

    Virgopia, N.; Ferraioli, F.

    1987-01-01

    The problem of weak-discontinuity propagation in mixtures of two ideal fluids is examined. The presence of exchenge of momentum reduces or enhances the time for shock formation depending on the machanism with whom the exchange of momentum takes place. Numerical evaluation are also presented for mixtures of nitrogen and oxygen simulating dry-air models

  3. The Modified Enskog Equation for Mixtures

    NARCIS (Netherlands)

    Beijeren, H. van; Ernst, M.H.

    1973-01-01

    In a previous paper it was shown that a modified form of the Enskog equation, applied to mixtures of hard spheres, should be considered as the correct extension of the usual Enskog equation to the case of mixtures. The main argument was that the modified Enskog equation leads to linear transport

  4. Mixture toxicity of PBT-like chemicals

    DEFF Research Database (Denmark)

    Syberg, Kristian; Dai, Lina; Ramskov, Tina

    addition is a suitable model for default estimations of mixture effects. One of the major challenges is therefore how to select specific chemicals for actual mixture toxicity assessments. Persistant chemicals are likely to be present in the environment for an extended period of time, thus increasing...... the likelihood of them being present in environmentally found mixtures. Persistant, bioaccumulative and toxic (PBT) chemicals are therefore a highly relevant group of chemicals to consider for mixture toxicity regulation. The present study evaluates to what extent a number of PBT-like chemicals posess concern...... beyond that of the individual components. Firstly, the effects of three chemicals with PBT-like properties (acetyl cedrene, pyrene and triclosan) was examined on the freshwater snail, Potamopyrgus antipodarum. Secondly, mixture bioaccumulation of the same three chemicals were assessed experimentally...

  5. A binary mixture operated heat pump

    International Nuclear Information System (INIS)

    Hihara, E.; Saito, T.

    1991-01-01

    This paper evaluates the performance of possible binary mixtures as working fluids in high- temperature heat pump applications. The binary mixtures, which are potential alternatives of fully halogenated hydrocarbons, include HCFC142b/HCFC22, HFC152a/HCFC22, HFC134a/HCFC22. The performance of the mixtures is estimated by a thermodynamic model and a practical model in which the heat transfer is considered in heat exchangers. One of the advantages of binary mixtures is a higher coefficient of performance, which is caused by the small temperature difference between the heat-sink/-source fluid and the refrigerant. The mixture HCFC142b/HCFC22 is promising from the stand point of thermodynamic performance

  6. Radiolytic decomposition of water-ethanol mixtures

    International Nuclear Information System (INIS)

    Baquey, Charles

    1968-07-01

    This research thesis addresses the study of the behaviour of binary mixtures submitted to ionizing radiations, and notably aims, by studying the case of water-ethanol mixtures, at verifying solutions proposed by previously published works on the origin of hydrogen atoms and of molecular hydrogen, on the intervention of excited atoms, and on the origin of products appearing under radiolysis. The experimental part of this work consists in the dosing of products formed in water-ethanol mixtures irradiated in presence or absence of nitrate, hydrogen, hydrocarbon, acetaldehyde, 2-3 butanediol and nitrite. Results are discussed and interpreted in terms of acetaldehyde efficiency, 2-3 butanediol efficiencies, and hydrocarbon efficiencies in pure ethanol, and in water-ethanol mixtures. The influence of the presence of nitrate ions in mixtures is also discussed

  7. Deformation Properties and Fatigue of Bituminous Mixtures

    Directory of Open Access Journals (Sweden)

    Frantisek Schlosser

    2013-01-01

    Full Text Available Deformation properties and fatigue performance are important characteristics of asphalt bound materials which are used for construction of pavement layers. Viscoelastic asphalt mixtures are better characterized via dynamic tests. This type of tests allows us to collate materials with regard to axle vibrations which lie usually in the range of 6 Hz–25 Hz for standard conditions. Asphalt modified for heat sensitivity in the range from −20°C to +60°C has significant impact on the overall characteristics of the mixture. Deformation properties are used as inputs for empirical mixture design, and fatigue performance of asphalt mixtures reflects the parameters of functional tests. Master curves convey properties of asphalt mixtures for various conditions and allow us to evaluate them without the need of time expensive testing.

  8. Preliminary studies on the closed cycle magneto aerodynamic converter; Etudes preliminaires sur les convertisseurs magnetohydrodynamiques fonctionnant hors d'equilibre thermodynamique

    Energy Technology Data Exchange (ETDEWEB)

    Ricateau, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Besides the open cycle MHD converters which convert the thermal energy contained in combustion gases, a closed cycle converter which can work with any high temperature heat source and specially with nuclear sources is being very carefully studied. Before proceeding to a practical study of the power station as a whole the performances of the converter itself must be fully investigated. These performances are largely a function of the conductivity of the gas, but this conductivity must not be repaid by a temperature technically unacceptable for the heat exchanger. In the conversion fluid an ionizable seeding vapour such as caesium or potassium is mixed with a carrier gas, helium or argon. Purely thermal ionization is only efficient above 2 500 deg. K, whereas the electric field obtained by Induction in the converter can, under given conditions, increase the electron temperature and produce an ionization rate well above the equilibrium value. This allows the gas to be ionized at moderate temperature. Studies are under way in order to clarify the conditions required to produce extra-thermal ionization in seeded rare gases. Measurements have been performed with a 3-phase 500 kVA plasmatron with potassium-seeded argon. The outgoing gas is fed into a channel where the tensor components of conductivity are measured in the presence of a magnetic field. The values found under thermodynamic equilibrium conditions confirm the simple theory. This is not the case when the electrons are heated. Measurements of the same kind have been made by another method in caesium-seeded helium contained in an isothermal vessel at 1 900 deg. K. There also the equilibrium values are in good agreement, but non-equilibrium ionization seems to be lower than expected. The effect of electron heating inside the converter in the case of argon-. potassium mixture has been considered in a theoretical study. It is shown that the electrode set must be carefully subdivided along the channel, and that

  9. Multi-temperature mixture of fluids

    Directory of Open Access Journals (Sweden)

    Ruggeri Tommaso

    2009-01-01

    Full Text Available We present a survey on some recent results concerning the different models of a mixture of compressible fluids. In particular we discuss the most realistic case of a mixture when each constituent has its own temperature (MT and we first compare the solutions of this model with the one with a unique common temperature (ST . In the case of Eulerian fluids it will be shown that the corresponding (ST differential system is a principal subsystem of the (MT one. Global behavior of smooth solutions for large time for both systems will also be discussed through the application of the Shizuta-Kawashima condition. Then we introduce the concept of the average temperature of mixture based upon the consideration that the internal energy of the mixture is the same as in the case of a single-temperature mixture. As a consequence, it is shown that the entropy of the mixture reaches a local maximum in equilibrium. Through the procedure of Maxwellian iteration a new constitutive equation for non-equilibrium temperatures of constituents is obtained in a classical limit, together with the Fick's law for the diffusion flux. Finally, to justify the Maxwellian iteration, we present for dissipative fluids a possible approach of a classical theory of mixture with multi-temperature and we prove that the differences of temperatures between the constituents imply the existence of a new dynamical pressure even if the fluids have a zero bulk viscosity.

  10. Probabilistic mixture-based image modelling

    Czech Academy of Sciences Publication Activity Database

    Haindl, Michal; Havlíček, Vojtěch; Grim, Jiří

    2011-01-01

    Roč. 47, č. 3 (2011), s. 482-500 ISSN 0023-5954 R&D Projects: GA MŠk 1M0572; GA ČR GA102/08/0593 Grant - others:CESNET(CZ) 387/2010; GA MŠk(CZ) 2C06019; GA ČR(CZ) GA103/11/0335 Institutional research plan: CEZ:AV0Z10750506 Keywords : BTF texture modelling * discrete distribution mixtures * Bernoulli mixture * Gaussian mixture * multi-spectral texture modelling Subject RIV: BD - Theory of Information Impact factor: 0.454, year: 2011 http://library.utia.cas.cz/separaty/2011/RO/haindl-0360244.pdf

  11. Adsorption on mixtures of ion exchangers

    International Nuclear Information System (INIS)

    Triolo, R.; Lietzke, M.H.

    1979-01-01

    A theoretical study has been made of adsorption on mixtures of ion exchangers. The effect of variables such as the concentration of the ion being adsorbed, the concentration of the supporting electrolyte, loading, the values of the capacities and equilibrium constants for the various exchange processes, and the fraction of each adsorber in the mixture on the observed distribution coefficient has been investigated. A computer program has been written to facilitate the calculation of distribution coefficients for the adsorption of an ion on a given mixture of ion exchangers under a specified set of conditions

  12. Principles and practice of mixtures toxicology

    National Research Council Canada - National Science Library

    Mumtaz, Moiz

    2010-01-01

    ... accurate predictions for the adverse effects of mixtures has been limited by the difficulty of acquiring data for all the possible combinations of dose and time that exist even in simple mixtures. Such predictions are also compromised by our use of single-agent toxicity studies since most "realworld" exposures are to mixtures. This has resulted in a variety of approaches (models, protocols, techniques, etc.) to address these issues. These are described in detail in the two dozen chapters of this book along with ca...

  13. Contribution to the study of french pitchblendes; Contribution a l'etude des pechblendes francaises

    Energy Technology Data Exchange (ETDEWEB)

    Geffroy, J [Commissariat a l' Energie Atomique, Lab. de Mineralogie, Centre de Chatillon (France). Centre d' Etudes Nucleaires; Sarcia, J A [Commissariat a l' Energie Atomique, Div. de la Crouzille, Haute Vienne (France). Centre d' Etudes Nucleaires

    1955-07-01

    The authors first review the characteristics of uraninite-pitchblende, as deduced of present literature. They set apart from typical pitchblende a black oxide aspect, which probably corresponds to neo-formations, and a 'para-pitchblende' aspect, which they relate to deep sur-oxidation of normal pitchblende. They insist on the easy replacement of pitchblende by silica. and give indications as to changes in vein stones (fluorite, quartz, etc...). A detailed study of paragenesis and successions in french uranium districts follows (including discussion of uranium of uranium-bearing coals). The authors attempt to classify french pitchblende veins. They are chiefly epithermal and poor in satellite ores. Three types of deposits are identified: massive - pitchblende type, silica type, fluorite type. These deposits, as those of Portugal, are included in granite, Central-European peri-batholitic types where uranium associates which Ni, Co, Bi and Ag, are in France both rare and poor. Finally, the authors attempt to bring out in the european Hercynian area a particular distribution of paragenetic types. (authors) [French] Les auteurs recapitulent d'abord les caracteres et les occurences de l'uraninite - pechblende, tels qu'ils peuvent etre degages de l'actuelle bibliographie. Ils exposent ensuite les faits qui du point de vue mineralogique seulement ressortent de l'etude mineralogique et chalcographique des pechblendes francaises et de leurs satellites. Ils distinguent de la pechblende-type un facies oxyde noir; correspondant probablement a une neoformation, et un facies parapechblende, qui est rapporte a une sur oxydation hypogene de la pechblende proprement dite. Ils insistent sur le facile remaniement de la pechblende par la slice; et donnent quelques precisions sur les modifications des gangues (fluorine, quartz, etc...). Suit l'etude detaillee des parageneses et des successions dans les districts uraniferes francais: Divisions du Limousin, de Grury, de Lachaux et de

  14. The formation of scientists and technicians at the 'Centre d'Etudes Nucleaires' at Saclay; Formation des scientifiques et des techniciens au Centre d'Etudes Nucleaires de Saclay

    Energy Technology Data Exchange (ETDEWEB)

    Debiesse, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    The considerable needs in research workers and scientists which are asked by the nuclear energy obliged the Commissariat a l'Energie atomique to deal with a particular effort to increase the quantitative and qualitative formation of scientists. Most various ways have been used. 1- A National Institute of Nuclear Sciences and Nuclear Techniques was created, by a joint decree of the Prime Minister and the Minister for National Education (june 18, 1957). This Institute of Higher Teaching (250 students) indulges in the following matters: atomic engineering, quantum mechanics, theory and technic of particle accelerators, special metallurgy, radiobiology, thermic and mechanics of fluids. 2- An associated centre of the 'Conservatoire National des Arts et Metiers' waeated (200 students) for technical assistants, drawers, etc. 3- In contribution with both electronic industry and Ministry of Work, the Centre d'Etudes Nucleaires contributes to an accelerated formation of technical assistants into Professional Centres. Conclusion: Training of scientists and research workers is one of the most important activities of the Centre d'Etudes Nucleaires de Saclay. Without losing its technical efficiency, it has supplied and varied means adapted to the various purposes that we shall reach. (author)Fren. [French] Les besoins considerables actuels et previsibles en chercheurs et scientifiques necessites par l'avevement de l'energie nucleaire imposaient au Commissariat a I'Energie atomique un effort particulier pour augmenter la formation quantitative et qualitative des scientifiques. Les moyens les plus divers ont ete mis en oeuvre: 1- Creation de l'Institut National des Sciences et Techniques Nucleaires par decret de la Presidence du Conseil et de l'Education Nationale en date du 18.6.57. Cet Institut d'Enseignement Superieur (250 etudiants) donne des cours en: genie atomique, mecanique quantique, theorie et technique des Accelerateurs de particules, metallurgie speciale, radiobiologie

  15. Quantiles for Finite Mixtures of Normal Distributions

    Science.gov (United States)

    Rahman, Mezbahur; Rahman, Rumanur; Pearson, Larry M.

    2006-01-01

    Quantiles for finite mixtures of normal distributions are computed. The difference between a linear combination of independent normal random variables and a linear combination of independent normal densities is emphasized. (Contains 3 tables and 1 figure.)

  16. Shear-induced phase changes in mixtures

    International Nuclear Information System (INIS)

    Romig, K.D.; Hanley, H.J.M.

    1986-01-01

    A thermodynamic theory to account for the behavior of liquid mixtures exposed to a shear is developed. One consequence of the theory is that shear-induced phase changes are predicted. The theory is based on a thermodynamics that includes specifically the shear rate in the formalism and is applied to mixtures by a straightforward modification of the corresponding states, conformalsolution approach. The approach is general but is used here for a mixture of Lennard-Jones particles with a Lennard-Jones equation of state as a reference fluid. The results are discussed in the context of the Scott and Van Konynenberg phase classification. It is shown that the influence of a shear does affect substantially the type of the phase behavior. Results from the model mixture are equated loosely with those from real polymeric liquids

  17. A simple approach to polymer mixture miscibility.

    Science.gov (United States)

    Higgins, Julia S; Lipson, Jane E G; White, Ronald P

    2010-03-13

    Polymeric mixtures are important materials, but the control and understanding of mixing behaviour poses problems. The original Flory-Huggins theoretical approach, using a lattice model to compute the statistical thermodynamics, provides the basic understanding of the thermodynamic processes involved but is deficient in describing most real systems, and has little or no predictive capability. We have developed an approach using a lattice integral equation theory, and in this paper we demonstrate that this not only describes well the literature data on polymer mixtures but allows new insights into the behaviour of polymers and their mixtures. The characteristic parameters obtained by fitting the data have been successfully shown to be transferable from one dataset to another, to be able to correctly predict behaviour outside the experimental range of the original data and to allow meaningful comparisons to be made between different polymer mixtures.

  18. Model structure selection in convolutive mixtures

    DEFF Research Database (Denmark)

    Dyrholm, Mads; Makeig, S.; Hansen, Lars Kai

    2006-01-01

    The CICAAR algorithm (convolutive independent component analysis with an auto-regressive inverse model) allows separation of white (i.i.d) source signals from convolutive mixtures. We introduce a source color model as a simple extension to the CICAAR which allows for a more parsimonious represent......The CICAAR algorithm (convolutive independent component analysis with an auto-regressive inverse model) allows separation of white (i.i.d) source signals from convolutive mixtures. We introduce a source color model as a simple extension to the CICAAR which allows for a more parsimonious...... representation in many practical mixtures. The new filter-CICAAR allows Bayesian model selection and can help answer questions like: ’Are we actually dealing with a convolutive mixture?’. We try to answer this question for EEG data....

  19. Modelling of an homogeneous equilibrium mixture model

    International Nuclear Information System (INIS)

    Bernard-Champmartin, A.; Poujade, O.; Mathiaud, J.; Mathiaud, J.; Ghidaglia, J.M.

    2014-01-01

    We present here a model for two phase flows which is simpler than the 6-equations models (with two densities, two velocities, two temperatures) but more accurate than the standard mixture models with 4 equations (with two densities, one velocity and one temperature). We are interested in the case when the two-phases have been interacting long enough for the drag force to be small but still not negligible. The so-called Homogeneous Equilibrium Mixture Model (HEM) that we present is dealing with both mixture and relative quantities, allowing in particular to follow both a mixture velocity and a relative velocity. This relative velocity is not tracked by a conservation law but by a closure law (drift relation), whose expression is related to the drag force terms of the two-phase flow. After the derivation of the model, a stability analysis and numerical experiments are presented. (authors)

  20. Viscosities of corium-concrete mixtures

    International Nuclear Information System (INIS)

    Seiler, J.M.; Ganzhorn, J.

    1997-01-01

    Severe accidents on nuclear reactors involve many situations such as pools of molten core material, melt spreading, melt/concrete interactions, etc. The word 'corium' designates mixtures of materials issued from the molten core at high temperature; these mixtures involve mainly: UO2, ZrO2, Zr and, in small amounts, Ni, Cr, Ag, In, Cd. These materials, when flowing out of the reactor vessel, may interact with the concrete of the reactor building thus introducing decomposition products of concrete into the original mixture. These decomposition products are mainly: SiO 2 , FeO, MgO, CaO and Al 2 O 3 in different amounts depending on the nature of the concrete being considered. Siliceous concrete is rich in SiO 2 , limestone concrete contains both SiO 2 and CaO. Liquidus temperatures of such mixtures are generally obove 2300 K whereas solidus temperatures are ∝1400 K. (orig.)

  1. Negative muon capture in noble gas mixtures

    International Nuclear Information System (INIS)

    Hutson, R.L.; Knight, J.D.; Leon, M.; Schillaci, M.E.; Knowles, H.B.; Reidy, J.J.

    1980-01-01

    We have determined the probabilities of atomic negative muon capture in binary mixtures of the gases He, Ne, Ar, and Kr at partial pressures near five atmospheres. Relative capture rates were deduced from measured muonic X-ray yields. (orig.)

  2. Mixture design procedure for flexible base.

    Science.gov (United States)

    2013-04-01

    This document provides information on mixture design requirements for a flexible base course. Sections : design requirements, job mix formula, contractor's responsibility, and engineer's responsibility. Tables : material requirements; requirements fo...

  3. Predicting skin permeability from complex chemical mixtures

    International Nuclear Information System (INIS)

    Riviere, Jim E.; Brooks, James D.

    2005-01-01

    Occupational and environmental exposure to topical chemicals is usually in the form of complex chemical mixtures, yet risk assessment is based on experimentally derived data from individual chemical exposures from a single, usually aqueous vehicle, or from computed physiochemical properties. We present an approach using hybrid quantitative structure permeation relationships (QSPeR) models where absorption through porcine skin flow-through diffusion cells is well predicted using a QSPeR model describing the individual penetrants, coupled with a mixture factor (MF) that accounts for physicochemical properties of the vehicle/mixture components. The baseline equation is log k p = c + mMF + aΣα 2 H + bΣβ 2 H + sπ 2 H + rR 2 + vV x where Σα 2 H is the hydrogen-bond donor acidity, Σβ 2 H is the hydrogen-bond acceptor basicity, π 2 H is the dipolarity/polarizability, R 2 represents the excess molar refractivity, and V x is the McGowan volume of the penetrants of interest; c, m, a, b, s, r, and v are strength coefficients coupling these descriptors to skin permeability (k p ) of 12 penetrants (atrazine, chlorpyrifos, ethylparathion, fenthion, methylparathion, nonylphenol, ρ-nitrophenol, pentachlorophenol, phenol, propazine, simazine, and triazine) in 24 mixtures. Mixtures consisted of full factorial combinations of vehicles (water, ethanol, propylene glycol) and additives (sodium lauryl sulfate, methyl nicotinate). An additional set of 4 penetrants (DEET, SDS, permethrin, ricinoleic acid) in different mixtures were included to assess applicability of this approach. This resulted in a dataset of 16 compounds administered in 344 treatment combinations. Across all exposures with no MF, R 2 for absorption was 0.62. With the MF, correlations increased up to 0.78. Parameters correlated to the MF include refractive index, polarizability and log (1/Henry's Law Constant) of the mixture components. These factors should not be considered final as the focus of these studies

  4. On modeling of structured multiphase mixtures

    International Nuclear Information System (INIS)

    Dobran, F.

    1987-01-01

    The usual modeling of multiphase mixtures involves a set of conservation and balance equations of mass, momentum, energy and entropy (the basic set) constructed by an averaging procedure or postulated. The averaged models are constructed by averaging, over space or time segments, the local macroscopic field equations of each phase, whereas the postulated models are usually motivated by the single phase multicomponent mixture models. In both situations, the resulting equations yield superimposed continua models and are closed by the constitutive equations which place restrictions on the possible material response during the motion and phase change. In modeling the structured multiphase mixtures, the modeling of intrinsic motion of grains or particles is accomplished by adjoining to the basic set of field equations the additional balance equations, thereby placing restrictions on the motion of phases only within the imposed extrinsic and intrinsic sources. The use of the additional balance equations has been primarily advocated in the postulatory theories of multiphase mixtures and are usually derived through very special assumptions of the material deformation. Nevertheless, the resulting mixture models can predict a wide variety of complex phenomena such as the Mohr-Coulomb yield criterion in granular media, Rayleigh bubble equation, wave dispersion and dilatancy. Fundamental to the construction of structured models of multiphase mixtures are the problems pertaining to the existence and number of additional balance equations to model the structural characteristics of a mixture. Utilizing a volume averaging procedure it is possible not only to derive the basic set of field equation discussed above, but also a very general set of additional balance equations for modeling of structural properties of the mixture

  5. Muonium radicals in benzene-styrene mixtures

    International Nuclear Information System (INIS)

    Ng, B.W.; Stadlbauer, J.W.; Walker, D.C.

    1984-01-01

    Muonium radicals were observed through their μ + SR precession frequencies in high transverse magnetic fields in pure benzene, pure styrene and their mixtures, all as liquids at room temperature. In benzene-styrene mixtures, the radicals obtained in each pure liquid are both present, so no slow (10 -9 -10 -5 s) intermolecular exchange occurs; but strong selectivity was found with the formation of the radical from styrene being about eight-times more probable than the radical from benzene. (Auth.)

  6. Isotope mixtures of hydrogen in vanadium

    International Nuclear Information System (INIS)

    Mecking-Schloetensack, P.

    1982-03-01

    The properties of isotope-mixtures of Protium and Deuterium stored in Vanadium have been studied. Protium and Deuterium are existing as interstitial-atoms on tetrahedral sites as well as on octahedral sites in this system. This feature leads to large isotopic-effects between the two isotopes. The dependence of the thermodynamic functions like heat of solution, nonconfigurational entropy, specific heat and ordering temperatures from the composition of the isotope-mixture has been determined. (orig.)

  7. Thermodiffusion in multicomponent n-alkane mixtures.

    Science.gov (United States)

    Galliero, Guillaume; Bataller, Henri; Bazile, Jean-Patrick; Diaz, Joseph; Croccolo, Fabrizio; Hoang, Hai; Vermorel, Romain; Artola, Pierre-Arnaud; Rousseau, Bernard; Vesovic, Velisa; Bou-Ali, M Mounir; Ortiz de Zárate, José M; Xu, Shenghua; Zhang, Ke; Montel, François; Verga, Antonio; Minster, Olivier

    2017-01-01

    Compositional grading within a mixture has a strong impact on the evaluation of the pre-exploitation distribution of hydrocarbons in underground layers and sediments. Thermodiffusion, which leads to a partial diffusive separation of species in a mixture due to the geothermal gradient, is thought to play an important role in determining the distribution of species in a reservoir. However, despite recent progress, thermodiffusion is still difficult to measure and model in multicomponent mixtures. In this work, we report on experimental investigations of the thermodiffusion of multicomponent n -alkane mixtures at pressure above 30 MPa. The experiments have been conducted in space onboard the Shi Jian 10 spacecraft so as to isolate the studied phenomena from convection. For the two exploitable cells, containing a ternary liquid mixture and a condensate gas, measurements have shown that the lightest and heaviest species had a tendency to migrate, relatively to the rest of the species, to the hot and cold region, respectively. These trends have been confirmed by molecular dynamics simulations. The measured condensate gas data have been used to quantify the influence of thermodiffusion on the initial fluid distribution of an idealised one dimension reservoir. The results obtained indicate that thermodiffusion tends to noticeably counteract the influence of gravitational segregation on the vertical distribution of species, which could result in an unstable fluid column. This confirms that, in oil and gas reservoirs, the availability of thermodiffusion data for multicomponent mixtures is crucial for a correct evaluation of the initial state fluid distribution.

  8. Using Big Data Analytics to Address Mixtures Exposure

    Science.gov (United States)

    The assessment of chemical mixtures is a complex issue for regulators and health scientists. We propose that assessing chemical co-occurrence patterns and prevalence rates is a relatively simple yet powerful approach in characterizing environmental mixtures and mixtures exposure...

  9. Development of a gas-ionization {beta}-spectrometer; Etude et realisation d'un spectrometre {beta} a ionisation gazeuse

    Energy Technology Data Exchange (ETDEWEB)

    Le Du, R [Commissariat a l' Energie Atomique, Bruyeres-le-Chatel (France). Centre d' Etudes

    1968-05-15

    We intend to develop in our laboratory a {beta}-spectrometer. This apparatus will have two main objectives: 1 - the determination of the nature and the degree of purity of certain {beta}-emitting radioactive substances; 2 - the study of an activity calibration process for {beta}-emitting radioactive sources. (author) [French] Nous nous proposons d'etudier et de realiser dans notre laboratoire un spectrometre {beta}. Cet appareil aura deux buts principaux: 1 - determiner la nature et le degre de purete de certains corps radioactifs emetteurs {beta}; 2 - permettre l'etude d'un procede d'etalonnage en activite de sources radioactives emetteurs {beta}. (auteur)

  10. Preparation and study of dialkyl nitroxide radicals; Preparation et etude de radicaux nitroxydes diacyles

    Energy Technology Data Exchange (ETDEWEB)

    Chenavas, P. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    These radicals are obtained by oxidation of N-hydroxy-imides with lead tetracetate or p-nitro-perbenzoic acid. These imides are prepared by heating dicarboxylic acids anhydrides with benzyloxy-amine followed by catalytic hydrogenation of N-benzyloxy-imides so obtained. Two series of radicals have mainly been studied, the first concerning five-membered cyclic imides, the second six-membered cyclic imides, these molecules having methyls substituents or no on the carbon ring. N. M. R. spectra of some O-benzyl-imides have been analysed. These different results have made it possible to study the conformation and stereochemistry of these imides. (author) [French] Ces radicaux sont obtenus par oxydation d'imides N-hydroxyles par le tetracetate de plomb ou l'acide p-nitroperbenzoique; ces imides sont prepares par chauffage d'anhydrides de diacides en presence de benzyloxyamine suivie d'une hydrogenation catalytique des N-benzyloxyimides ainsi obtenus. Deux series de radicaux ont principalement ete etudies: la premiere relative a des imides cycliques a cinq chainons, la seconde a des imides cycliques a six chainons, ces molecules ayant des substituants methyles ou non sur la chaine carbonee. Les derives O-benzyles de quelques-uns de ces imides ont ete analyses en R. M. N. Ces differents resultats ont permis une etude de la conformation et de la stereochimie de ces imides. (auteur)

  11. The abject gaze and the homosexual body: Flandrin's Figure d'Etude.

    Science.gov (United States)

    Camille, M

    1994-01-01

    This article charts the history of the reception, reproduction and appropriation of a single image that has recently become a kind of "gay icon"--the Figure d'Etude in the Louvre, painted by Hippolyte Flandrin in 1835. Initially no more than a neo-classical academic exercise, the formal emptiness of this picture meant that it could be re-invested and reinscribed with new meanings and new titles at every turn. Emblematic of the anxious visibility/invisibility of the newly discovered homosexual body during a period when the gaze still had to be kept a dark secret, Flandrin's image only "came out" in its later photographic reworkings by Frederick Holland Day and Baron von Gloeden. After being reproduced for a specifically homosexual audience early this century, the popular Romantic pose of the young man curled-up in profile became a standard one, reappearing recently in the photographs of Robert Mapplethorpe. The inactive, abject and inward-turned isolation of the figure with its narcissistic self-absorption makes it, in my view, a profoundly negative stereotype of the gay gaze and the homosexual body. Flandrin's figure nonetheless appears today on gay merchandise world-wide as a sign of our separate and secluded subject positions and our community's unwillingness to radically alter older imposed and inherited classical stereotypes.

  12. Study of copper fluorination; Contribution a l'etude de la fluoruration du cuivre

    Energy Technology Data Exchange (ETDEWEB)

    Gillardeau, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-02-01

    This report deals with the action of fluorine on copper. Comprehensive descriptions are given of the particular technological methods and of the preparation of the reactants. This fluorination reaction has been studied at medium and low fluorine pressures. A nucleation and growth phenomenon is described. The influence of a pollution of the gas phase on the fluorination process is described. The solid-state reaction between cupric fluoride and cooper has also been studied. A special study has been made of the growth of copper deposits by thermal decomposition of gaseous fluorides. (author) [French] Ce rapport traite de la reaction du fluor sur le cuivre. Les methodes technologiques particulieres ainsi que les preparations des reactifs sont largement developpees. Cette reaction de fluoruration est etudiee sous pressions moyennes et sous basses pressions de fluor. Un phenomene de germination et croissance est decrit. L'influence de la pollution de la phase gazeuse sur le processus de fluoruration est rapportee. La reaction a l'etat solide du fluorure cuivrique sur le cuivre a egalement ete etudiee. La croissance de depots de cuivre par decomposition thermique des fluorures de cuivre gazeux fait l'objet d'une etude speciale. (auteur)

  13. Preparation and study of dialkyl nitroxide radicals; Preparation et etude de radicaux nitroxydes diacyles

    Energy Technology Data Exchange (ETDEWEB)

    Chenavas, P [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    These radicals are obtained by oxidation of N-hydroxy-imides with lead tetracetate or p-nitro-perbenzoic acid. These imides are prepared by heating dicarboxylic acids anhydrides with benzyloxy-amine followed by catalytic hydrogenation of N-benzyloxy-imides so obtained. Two series of radicals have mainly been studied, the first concerning five-membered cyclic imides, the second six-membered cyclic imides, these molecules having methyls substituents or no on the carbon ring. N. M. R. spectra of some O-benzyl-imides have been analysed. These different results have made it possible to study the conformation and stereochemistry of these imides. (author) [French] Ces radicaux sont obtenus par oxydation d'imides N-hydroxyles par le tetracetate de plomb ou l'acide p-nitroperbenzoique; ces imides sont prepares par chauffage d'anhydrides de diacides en presence de benzyloxyamine suivie d'une hydrogenation catalytique des N-benzyloxyimides ainsi obtenus. Deux series de radicaux ont principalement ete etudies: la premiere relative a des imides cycliques a cinq chainons, la seconde a des imides cycliques a six chainons, ces molecules ayant des substituants methyles ou non sur la chaine carbonee. Les derives O-benzyles de quelques-uns de ces imides ont ete analyses en R. M. N. Ces differents resultats ont permis une etude de la conformation et de la stereochimie de ces imides. (auteur)

  14. Study of {gamma}'s in Naiade; Etude des gamma de Naiade

    Energy Technology Data Exchange (ETDEWEB)

    Millot, J P; Rastoin, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    Following a study of the gamma sources, the flux of gamma of different energies in the swimming pool is investigated. The biological dose can thus be obtained by calculation, and compared with the results given by photographic plates. The influence of photoneutrons is estimated by calculation, and research is being carried out on their influence on the thermal neutron flux curve on the axis of the uranium plate, with the plate emitting neutrons and with the plate protected by boral. (author) [French] Apres l'etude des sources de gamma, l'on etudie le flux de gamma de differentes energies dans la piscine. La dose biologique peut etre obtenue ainsi par le calcul et comparee avec les resultats donnes par les plaques photographiques. L'influence des photoneutrons est estimee par le calcul et l'on recherche leur influence sur la courbe de flux de neutrons thermiques sur l'axe de la plaque d'uranium, la plaque emettant des neutrons et la plaque protegee par du boral. (auteur)

  15. Technological study of organic fluids; Etudes technologiques des fluides caloporteurs organique

    Energy Technology Data Exchange (ETDEWEB)

    Leveque, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Under contract to EURATOM (MM. VAN der VENNE and HANNAERT), the C.E.A. and the Progil Society have collaborated on a technological study of the terphenyls. The results obtained from the radiolysis and pyrolysis of the product OM2 (70 p. 100 m-terphenyl, 25 p. 100 o-terphenyl, 5 p. 100 p-terphenyl) are reported. Using two pile loops at temperatures up to 450 deg. C, a phenomena of accelerated pyrolysis on the radiolized material has been demonstrated. Some by-products of the petroleum industry have also been studied, with a view to finding substitutes for terphenyl. (author) [French] Le C.E.A. et la Societe PROGIL ont entrepris en commun sous contrat EURATOM (MM. VAN der VENNE et HANNAERT) une etude technologique des terphenyles. Les resultats de radiolyse et de pyrolyse obtenus sur le produit OM2 (70 p. 100 m-terphenyle, 25 p. 100 o-terphenyle. 5 p. 100 de p-terphenyle) sont exposes. L'exploitation de deux boucles en pile jusqu'a des temperatures de 450 deg. C a mis en evidence un phenomene de pyrolyse acceleree sur le produit radiolyse. On a etudie egalement quelques sous-produits de l'industrie petroliere dans le but de trouver des substituts au terphenyle. (auteur)

  16. Underground nuclear explosions. Geological survey of the cavities; Explosions nucleaires souterraines etude geologique des cavites

    Energy Technology Data Exchange (ETDEWEB)

    Faure, J [Commissariat a l' Energie Atomique, Bruyeres-le-Chatel (France). Centre d' Etudes

    1969-07-01

    A geological survey of underground nuclear explosions makes it possible to determine the main characteristics of the cavity formed. The lower portion is spherical; the same was very likely true of the roof, which collapses in the majority of media with the exception of rock-salt. Its radius, for a given bomb size, can vary by a factor of two according to the type of rock. The lay-out of its contents depends on the characteristics of the solid and liquid products at the moment of the roof collapse; according to the medium involved, mixing of the rubble and the mud-flow occurs (granite) or does not occur (tuff and alluvia). In all media, the average physical properties can be evaluated. (author) [French] L'etude geologique d'explosions nucleaires souterraines permet de determiner les principaux caracteres de la cavite creee. Sa partie inferieure est spherique; il en etait vraisemblablement de meme de sa voute, effondree dans la plupart des milieux a l'exception du sel gemme. Son rayon, a energie d'engin egale, varie selon les roches du simple au double. La disposition de son contenu depend des caracteristiques des produits solides et liquides au moment de la chute du toit; selon le cas, il n'y a pas (tuf et alluvions) ou il y a (granite) melange des eboulis et des laves. Dans tous les milieux, les proprietes physiques moyennes peuvent etre evaluees. (auteur)

  17. A turbulence model in mixtures. First part: Statistical description of mixture

    International Nuclear Information System (INIS)

    Besnard, D.

    1987-03-01

    Classical theory of mixtures gives a model for molecular mixtures. This kind of model is based on a small gradient approximation for concentration, temperature, and pression. We present here a mixture model, allowing for large gradients in the flow. We also show that, with a local balance assumption between material diffusion and flow gradients evolution, we obtain a model similar to those mentioned above [fr

  18. Detonation study of two stoichiometric mixtures (CH{sub 4}/H{sub 2}/O{sub 2}/N{sub 2} and CH{sub 4}/C{sub 2}H{sub 6}/O{sub 2}/N{sub 2}). Influence of the relative proportion of both fuels and of the initially high temperature; Etude de la detonation de deux melanges stoechiometriques (CH{sub 4}/H{sub 2}/O{sub 2}/N{sub 2} et CH{sub 4}/C{sub 2}H{sub 6}/O{sub 2}/N{sub 2}). Influence de la proportion relative des deux combustibles et de la temperature initiale elevee

    Energy Technology Data Exchange (ETDEWEB)

    Matignon, Ch.

    2000-12-15

    Detonations of gaseous reactive mixtures made of two fuels of very different detonability xH{sub 2}+(1-x)CH{sub 4} and xC{sub 2}H{sub 6}+(1-x)CH{sub 4} in stoichiometric proportion with oxygen and diluted with nitrogen (in proportions varying from pure oxygen to the air) are investigated. The parameters of the study are the relative proportion x of fuels, nitrogen dilution B = O{sub 2}/N{sub 2} and the initial conditions of temperature and pressure. This study takes place within the general context of the chemical process safety improvement. Detonability was evaluated by the comparison between the characteristic cell size measurement of the three-dimensional structure of the autonomous and stationary detonation front with the chemical induction length calculated on the assumptions of the ZND model by means of several detailed chemical kinetics mechanisms. The results obtained for the mixtures with single fuel show that the detonability of methane decreases according to the initial temperature whatever the dilution B, and that the one of ethane and hydrogen decreases with B = 0 but increases with B = 3,76 (air) (the inversion of behaviour occurs for B = 2 for ethane, and B=1 for hydrogen). The results obtained for the mixtures with two fuels show that their detonability is each time influenced by the heaviest fuel, i.e. that the detonability of H{sub 2}/CH{sub 4} mixtures is rather controlled by CH{sub 4} whereas the one of C{sub 2}H{sub 6}/CH{sub 4} mixtures is rather controlled by C{sub 2}H{sub 6}. With pure oxygen (B = 0), these mixtures are desensitized by the increase of the initial temperature. Beyond a certain value x, an inversion of detonability according to x is observed. (author)

  19. Mixture toxicity revisited from a toxicogenomic perspective.

    Science.gov (United States)

    Altenburger, Rolf; Scholz, Stefan; Schmitt-Jansen, Mechthild; Busch, Wibke; Escher, Beate I

    2012-03-06

    The advent of new genomic techniques has raised expectations that central questions of mixture toxicology such as for mechanisms of low dose interactions can now be answered. This review provides an overview on experimental studies from the past decade that address diagnostic and/or mechanistic questions regarding the combined effects of chemical mixtures using toxicogenomic techniques. From 2002 to 2011, 41 studies were published with a focus on mixture toxicity assessment. Primarily multiplexed quantification of gene transcripts was performed, though metabolomic and proteomic analysis of joint exposures have also been undertaken. It is now standard to explicitly state criteria for selecting concentrations and provide insight into data transformation and statistical treatment with respect to minimizing sources of undue variability. Bioinformatic analysis of toxicogenomic data, by contrast, is still a field with diverse and rapidly evolving tools. The reported combined effect assessments are discussed in the light of established toxicological dose-response and mixture toxicity models. Receptor-based assays seem to be the most advanced toward establishing quantitative relationships between exposure and biological responses. Often transcriptomic responses are discussed based on the presence or absence of signals, where the interpretation may remain ambiguous due to methodological problems. The majority of mixture studies design their studies to compare the recorded mixture outcome against responses for individual components only. This stands in stark contrast to our existing understanding of joint biological activity at the levels of chemical target interactions and apical combined effects. By joining established mixture effect models with toxicokinetic and -dynamic thinking, we suggest a conceptual framework that may help to overcome the current limitation of providing mainly anecdotal evidence on mixture effects. To achieve this we suggest (i) to design studies to

  20. A constitutive theory of reacting electrolyte mixtures

    Science.gov (United States)

    Costa Reis, Martina; Wang, Yongqi; Bono Maurizio Sacchi Bassi, Adalberto

    2013-11-01

    A constitutive theory of reacting electrolyte mixtures is formulated. The intermolecular interactions among the constituents of the mixture are accounted for through additional freedom degrees to each constituent of the mixture. Balance equations for polar reacting continuum mixtures are accordingly formulated and a proper set of constitutive equations is derived with basis in the Müller-Liu formulation of the second law of thermodynamics. Moreover, the non-equilibrium and equilibrium responses of the reacting mixture are investigated in detail by emphasizing the inner and reactive structures of the medium. From the balance laws and constitutive relations, the effects of molecular structure of constituents upon the fluid flow are studied. It is also demonstrated that the local thermodynamic equilibrium state can be reached without imposing that the set of independent constitutive variables is time independent, neither spatially homogeneous nor null. The resulting constitutive relations presented throughout this work are of relevance to many practical applications, such as swelling of clays, developing of bio and polymeric membranes, and use of electrorheological fluids in industrial processes. The first author acknowledges financial support from National Counsel of Technological and Scientific Development (CNPq) and German Academic Exchange Service (DAAD).

  1. Yield and competition in barley variety mixtures

    Directory of Open Access Journals (Sweden)

    Kari Jokinen

    1991-09-01

    Full Text Available Competition between spring barley varieties and yield performance of two-, three and four-variety mixtures were studied in two replacement series field experiments. In the first experiment, repeated in three successive years (1983 —85 the components were the six-row varieties Agneta, Arra, Hja-673 and Porno. In the second experiment (1984, including two nitrogen doses (50 and 100 kgN/ha, both six-row (Agneta, Pomo and two-row (Ida, Kustaa varieties were used. Arra in the first and Agneta in the second experiment were the most competitive varieties. The results suggested that the fast growth of Arra at the beginning promoted its competitive ability. Increase in available nitrogen usually strengthened the competitiveness of Agneta. The observed competitive differences between varieties were not related to the earliness of a variety, neither to the morphological characters (two- and six-row varieties nor to the grain yield of a variety grown alone. The competitive ability was not always a stable character, the dominant suppression relationship varying from one environment to another (e.g. growing season, nitrogen dose. The observed overyielding was not statistically significant. The ratio of actual to expected yield and the relative yield total of several mixtures exceeded slightly one. As a conclusion, the yield advantage of mixtures was marginal. As a rule, the mixtures were not more stable than monocultures as determined by the coefficient of variation. However, the yield of some mixtures varied less than the yield of the most stable monoculture.

  2. Study: control of atomic energy power plant; Etude de la regulation d'une installation atomique productrice d'energie

    Energy Technology Data Exchange (ETDEWEB)

    Dautray, R; Leny, J C [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    We are studying the control of a very flexible atomic power plant, able to supply an independent network. Two systems have been examined: in the first the moderator pre-heats the light water, in the second, this preheating is dispensed with, subsequent to a study of the dynamics of the plant. Very complete linear approximation study is being effected on the model of the second system, all effects being taken into account. The reactor is stable at all power levels, though slight reactivity or load variations cause undamped power oscillations around the equilibrium level. (author)Fren. [French] Nous etudions la regulation d'une installation atomique d'une grande souplesse, pouvant eventuellement fournir de l'energie a un reseau isole. Deux versions de l'installation sont etudiees: dans la premiere le moderateur sert a rechauffer l'eau industrielle, mais l'etude dynamique conduit a supprimer ce rechauffage, ce qui donne la deuxieme version. On effectue sur celle-ci une etude en approximation lineaire tres complete ou l'on tient compte de differents effets. L'installation se montre stable a tous les niveaux de puissance. Toutefois, de petites perturbations de reactivite ou de charge entrainent des oscillations de puissance mal amorties autour de la position d'equilibre. (auteur)

  3. Methods for studying the radioactive contamination of plants (1963); Methodes d'etude de la contamination radioactive des vegetaux (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Coulon, R; Jeanmaire, L; Michon, G [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1963-07-01

    The authors first define the doctrine which led to the devising of a method for studying the radioactive pollution of plants, based on the use of simple techniques, having the possibility of being adapted for routine work, and so devised that each stage is proceeded with only if the preceding one justifies it. For each stage a study is effected comparing the results obtained by the use of more exact techniques. The second part describes in detail the techniques used. (authors) [French] Dans une premiere partie lea auteurs definissent la doctrine qui leur a permis d'elaborer une methode d'etude de la pollution radioactive des vegetaux, basee sur l'utilisation de techniques simples, se pretant au travail de serie et concues de telle maniere que chaque etape n'est abordee que si la precedente le justifie. Chaque etape fait l'objet d'une etude qui compare les resultats a ceux obtenue par des techniques plus precises. La deuxieme partie decrit dans le detail les techniques utilisees. (auteurs)

  4. Experimental investigation of CO_2 separation by adsorption methods in natural gas purification

    International Nuclear Information System (INIS)

    Chen, S.J.; Fu, Y.; Huang, Y.X.; Tao, Z.C.; Zhu, M.

    2016-01-01

    Highlights: • The ideal swing adsorption tank can improve the adsorption performance. • Pure CO_2 adsorption experimental data agrees well with extended Langmuir model. • Langmuir-Freundlich model correlates CO_2/CH_4 mixture adsorption data fairly well. • The temperature increases in the order swing 2 > swing1 > static for pure CO_2 adsorption. • Swinging the adsorption tank can improve the separation efficiency. - Abstract: CO_2 separation for natural gas purification by the adsorption method was studied in detail using volumetric adsorption apparatus. The crystalline phase and microstructure of the experimental sample were analyzed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and Micromeritics ASAP 2020 instrument. The XRD pattern proves that the experimental sample consists of 13X zeolites. The SEM images show that the 13X zeolites expose a large number of micro-channels on the surface of the particles. The microporous volume is 0.22 cm"3 (STP)/g. The ideal swing frequency for the adsorption tank can improve the adsorption performance of an adsorbent compared with a static adsorption tank. The pure CO_2 adsorption experimental data agrees well with the extended Langmuir model. The Langmuir-Freundlich model correlates the CO_2/CH_4 mixture adsorption experimental data fairly well. The relative errors between the simulated results and the experimental data are very little, which indicates that these fitted models are correct. The average selectivity of CO_2/CH_4 in a static and swing adsorption tank are, respectively, 3.57 and 3.93, considerably higher than 1, indicating preferential CO_2 adsorption over CH_4 in CO_2/CH_4 mixtures. This also shows that the swing can improve CO_2 separation for natural gas purification. For the three types of motion status, the temperature of the adsorption tank increased in the order swing 2 > swing1 > static state for pure CO_2 adsorption in 13X zeolites. The temperature variation decreased as the

  5. Detonation velocity in poorly mixed gas mixtures

    Science.gov (United States)

    Prokhorov, E. S.

    2017-10-01

    The technique for computation of the average velocity of plane detonation wave front in poorly mixed mixture of gaseous hydrocarbon fuel and oxygen is proposed. Here it is assumed that along the direction of detonation propagation the chemical composition of the mixture has periodic fluctuations caused, for example, by layered stratification of gas charge. The technique is based on the analysis of functional dependence of ideal (Chapman-Jouget) detonation velocity on mole fraction (with respect to molar concentration) of the fuel. It is shown that the average velocity of detonation can be significantly (by more than 10%) less than the velocity of ideal detonation. The dependence that permits to estimate the degree of mixing of gas mixture basing on the measurements of average detonation velocity is established.

  6. DCMDN: Deep Convolutional Mixture Density Network

    Science.gov (United States)

    D'Isanto, Antonio; Polsterer, Kai Lars

    2017-09-01

    Deep Convolutional Mixture Density Network (DCMDN) estimates probabilistic photometric redshift directly from multi-band imaging data by combining a version of a deep convolutional network with a mixture density network. The estimates are expressed as Gaussian mixture models representing the probability density functions (PDFs) in the redshift space. In addition to the traditional scores, the continuous ranked probability score (CRPS) and the probability integral transform (PIT) are applied as performance criteria. DCMDN is able to predict redshift PDFs independently from the type of source, e.g. galaxies, quasars or stars and renders pre-classification of objects and feature extraction unnecessary; the method is extremely general and allows the solving of any kind of probabilistic regression problems based on imaging data, such as estimating metallicity or star formation rate in galaxies.

  7. The Viscosity of Organic Liquid Mixtures

    Science.gov (United States)

    Len, C. W.; Trusler, J. P. M.; Vesovic, V.; Wakeham, W. A.

    2006-01-01

    The paper reports measurements of the viscosity and density of two heavy hydrocarbon mixtures, Dutrex and Arab Light Flashed Distillate (ALFD), and of their mixtures with hydrogen. The measurements have been carried out with a vibrating-wire device over a range of temperatures from 399 to 547 K and at pressures up to 20 MPa. Measurements have also been carried out on systems in which hydrogen at different concentrations has been dissolved in the liquids. The measurements have an estimated uncertainty of ±5% for viscosity and ±2% for density and represent the first results on these prototypical heavy hydrocarbons. The results reveal that the addition of hydrogen reduces both the density and viscosity of the original hydrocarbon mixture at a particular temperature and pressure.

  8. Capillary condensation and adsorption of binary mixtures.

    Science.gov (United States)

    Weinberger, B; Darkrim-Lamari, F; Levesque, D

    2006-06-21

    The adsorption of equimolar binary mixtures of hydrogen-carbon dioxide, hydrogen-methane, and methane-carbon dioxide in porous material models is determined by grand canonical Monte Carlo simulations. The material models have an adsorbent surface similar to that of nanofibers with a herringbone structure. Our main result, which is relevant for hydrogen purification and carbon dioxide capture, is that the adsorption selectivities calculated for the mixtures can differ significantly from those deduced from simulations of the adsorption of pure gases, in particular, when one of the adsorbed gases presents a capillary condensation induced by confinement within the pore network. A comparison of our data is also made with theoretical models used in the literature for predicting the properties of the mixture adsorption.

  9. MICROBIAL QUALITY OF HONEY MIXTURE WITH POLLEN

    Directory of Open Access Journals (Sweden)

    Ján Mareček

    2011-02-01

    Full Text Available Normal 0 21 MicrosoftInternetExplorer4 The aim of this study was evaluation of microbial quality in raw materials (honey, pollen and evaluation of microbial quality in honey mixture with pollen (2.91 % and 3.85 % and also dynamics of microbial groups in honey mixtures with pollen after 14 days storage at the room temperature (approximately 25 °C and in cold store (8 °C. We used dilution plating method for testing of samples. Detections of total plate microbial count (aerobic and anaerobic microorganisms, sporulating bacteria, coliform bacteria, Bifidobacterium sp., Lactobacillus sp. and microscopic fungi were performed. In general, counts of microorganisms decreased in honey mixture with pollen compared to raw pollen and these counts increased compared to natural honey. Total plate count was 5.37 log KTJ.g-1 in pollen; 1.36 log KTJ.g-1 in honey; 2.97 log KTJ.g-1 in honey mixture with 2.91 % pollen and 2.04 log KTJ.g-1 in honey mixture with 3.85 % pollen. Coliform bacteria were detected in pollen (1.77 log KTJ.g-1. Then, we found coliform bacteria in one sample of honey mixtures with pollen (2.91 % - 1.00 log KTJ.g-1.Bifidobacterium species were detected only in raw pollen. We did not findLactobacillus sp. in any of the samples. Microscopic fungi were detected on two cultivating media. Yeasts were present in pollen sample (average 5.39 log KTJ.g-1, honey mixture with 2.91 % pollen (average 2.51 log KTJ.g-1 and honey mixture with 3.85 % pollen (average 1.58 log KTJ.g-1. Filamentous microscopic fungi were detectable in pollen (average 3.38 log KTJ.g-1, in honey (only on one medium: 1.00 log KTJ.g-1, in honey mixture with 2.91 % pollen (average 1.15 log KTJ.g-1 and in honey mixture with 3.85 % pollen (1.71 %. Raw pollen contained microscopic fungi as Absidiasp., Mucor sp., Alternaria sp. andEmericella nidulans. Honey mixture with 2.91 % pollen after storage (14 days contained lower microbial counts when compared with the sample

  10. Flows and chemical reactions in homogeneous mixtures

    CERN Document Server

    Prud'homme, Roger

    2013-01-01

    Flows with chemical reactions can occur in various fields such as combustion, process engineering, aeronautics, the atmospheric environment and aquatics. The examples of application chosen in this book mainly concern homogeneous reactive mixtures that can occur in propellers within the fields of process engineering and combustion: - propagation of sound and monodimensional flows in nozzles, which may include disequilibria of the internal modes of the energy of molecules; - ideal chemical reactors, stabilization of their steady operation points in the homogeneous case of a perfect mixture and c

  11. in Binary Liquid Mixtures of Ethyl benzoate

    Directory of Open Access Journals (Sweden)

    Shaik Babu

    2012-01-01

    Full Text Available Ultrasonic velocity is measured at 2MHz frequency in the binary mixtures of Ethyl Benzoate with 1-Propanol, 1-Butanol, 1-Pentanol and theoretical values of ultrasonic velocity have been evaluated at 303K using Nomoto's relation, Impedance relation, Ideal mixture relation, Junjie's method and free length theory. Theoretical values are compared with the experimental values and the validity of the theories is checked by applying the chi-square test for goodness of fit and by calculating the average percentage error (APE. A good agreement has been found between experimental and Nomoto’s ultrasonic velocity.

  12. Robust classification using mixtures of dependency networks

    DEFF Research Database (Denmark)

    Gámez, José A.; Mateo, Juan L.; Nielsen, Thomas Dyhre

    2008-01-01

    Dependency networks have previously been proposed as alternatives to e.g. Bayesian networks by supporting fast algorithms for automatic learning. Recently dependency networks have also been proposed as classification models, but as with e.g. general probabilistic inference, the reported speed......-ups are often obtained at the expense of accuracy. In this paper we try to address this issue through the use of mixtures of dependency networks. To reduce learning time and improve robustness when dealing with data sparse classes, we outline methods for reusing calculations across mixture components. Finally...

  13. Plasma assisted combustion of parafin mixture

    International Nuclear Information System (INIS)

    Nedybaliuk, O.A.; Chernyak, V.Ya.; Martysh, E.V.; Lisitchenko, T.E.; Vergun, O.Yu.; Orlovska, S.G.

    2013-01-01

    In this work the results of solid paraffin combustion with the aid of the plasma of transverse and rotational gliding arc studies are represented. The question of the additional activation of paraffin based solid fuels is examined. The mixture of n-paraffin and stearin in the solid state as the model of the solid paraffin based fuel is used. The plasma assisted combustion of this model is experimentally investigated. The voltage-current characteristics of discharge at the different regimes are measured. The population temperatures of excited rotational levels are determined. The flame temperature during the combustion of solid paraffin containing mixture is calculated

  14. Productivity, botanical composition, and nutritive value of commercial pasture mixtures

    Science.gov (United States)

    Pastures in the northeastern USA often are planted to mixtures of grasses and legumes. There is limited public sector information on the performance of commercial forage mixtures. We evaluated a range of commercial pasture mixtures to determine if the number of species in a mixture affected yield an...

  15. Separation of alcohols from organic liquid mixtures by pervaporation

    NARCIS (Netherlands)

    Park, Hyun-Chae

    1993-01-01

    In the chemical industry, distillation is generally the preferred technique to separate a liquid mixture. However some liquid mixtures such as azeotropic mixtures, close-boiling hydrocarbons, and various isomers are difficult to separate by simple distillation. For the separation of these mixtures

  16. Contribution to the study of french pitchblendes; Contribution a l'etude des pechblendes francaises

    Energy Technology Data Exchange (ETDEWEB)

    Geffroy, J. [Commissariat a l' Energie Atomique, Lab. de Mineralogie, Centre de Chatillon (France). Centre d' Etudes Nucleaires; Sarcia, J.A. [Commissariat a l' Energie Atomique, Div. de la Crouzille, Haute Vienne (France). Centre d' Etudes Nucleaires

    1955-07-01

    The authors first review the characteristics of uraninite-pitchblende, as deduced of present literature. They set apart from typical pitchblende a black oxide aspect, which probably corresponds to neo-formations, and a 'para-pitchblende' aspect, which they relate to deep sur-oxidation of normal pitchblende. They insist on the easy replacement of pitchblende by silica. and give indications as to changes in vein stones (fluorite, quartz, etc...). A detailed study of paragenesis and successions in french uranium districts follows (including discussion of uranium of uranium-bearing coals). The authors attempt to classify french pitchblende veins. They are chiefly epithermal and poor in satellite ores. Three types of deposits are identified: massive - pitchblende type, silica type, fluorite type. These deposits, as those of Portugal, are included in granite, Central-European peri-batholitic types where uranium associates which Ni, Co, Bi and Ag, are in France both rare and poor. Finally, the authors attempt to bring out in the european Hercynian area a particular distribution of paragenetic types. (authors) [French] Les auteurs recapitulent d'abord les caracteres et les occurences de l'uraninite - pechblende, tels qu'ils peuvent etre degages de l'actuelle bibliographie. Ils exposent ensuite les faits qui du point de vue mineralogique seulement ressortent de l'etude mineralogique et chalcographique des pechblendes francaises et de leurs satellites. Ils distinguent de la pechblende-type un facies oxyde noir; correspondant probablement a une neoformation, et un facies parapechblende, qui est rapporte a une sur oxydation hypogene de la pechblende proprement dite. Ils insistent sur le facile remaniement de la pechblende par la slice; et donnent quelques precisions sur les modifications des gangues (fluorine, quartz, etc...). Suit l'etude detaillee des parageneses et des successions dans les districts uraniferes francais: Divisions du

  17. The dynamic behaviour of heat exchangers; Etude du comportement dynamique des echangeurs de chaleur

    Energy Technology Data Exchange (ETDEWEB)

    Fonteray, J; Rozenholc, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1963-07-01

    In order to study the dynamics of nuclear power plants, one needs mathematical models made up of ordinary differential equations. This report deals with models for heat exchangers. These models allow exact evaluations of the temperatures for any steady state. The deformation of the temperature maps during transients is taken into account. To do this, average temperatures are evaluated keeping In mind, on one hand the partial differential equations, on the other hand, the physical phenomenons which are involved. Seven ordinary differential equations at most, are necessary for one heat exchanger. Theses models were compared with mathematically exact ones and also with experimental results, that EDF was able to measure on EDF-1 heat exchangers. The results appear to be correct. (authors) [French] Les etudes de dynamique sur les centrales nucleaires exigent l'elaboration de modeles apparaissant sous forme d'equations differentlelles ordinaires. Ce rapport est consacre a la recherche de modeles d'echangeurs. Dans ces modeles les temperatures sont calculees exactement pour n'importe quel regime permanent. Pour tenir compte de la deformation des distributions de temperature en regime transitoire, on evalue les temperatures moyennes dans l'echangeur en s'appuyant, d'une part, sur les equations aux derivees partielles et, d'autre part, sur une analyse des phenomenes physiques. Les modeles contiennent au plus sept equations differentielles ordinaires. Ces modeles ont ete compares aux modeles mathematiques exacts et aussi a des resultats experimentaux, obtenus par l'EDF, sur les echangeurs d'EDF-1. Les resultats paraissent satisfaisants. (auteurs)

  18. Etude theorique et experimentale des evaporateurs de dioxyde de carbone operant dans des conditions de givrage

    Science.gov (United States)

    Bendaoud, Adlane Larbi

    Les evaporateurs de refrigeration sont surtout du type tube a ailettes, appeles serpentins, et fonctionnent dans l'une des conditions suivantes: seche, humide ou avec formation de givre. Il a ete demontre que la formation du givre sur la paroi exterieure de l'echangeur engendre une surconsommation energetique a cause des operations de degivrage puisque 15 a 20% seulement de la chaleur produite sert au degivrage tandis que le reste est dissipee dans l'environnement [1]. Avec l'avenement des nouveaux refrigerants, moins nocifs envers l'environnement, l'industrie du froid se trouve penalisee du fait que peu ou pas de composantes mecaniques (compresseur, pompe, echangeur...etc.) adaptees sont disponibles [3]. Il s'agit pour la communaute des frigoristes de combler ce retard technologique en redeveloppant ces composantes mecaniques afin qu'elles soient adaptees aux nouveaux refrigerants. Dans cette optique, et afin de mieux comprendre le comportement thermique des evaporateurs au CO2 fonctionnant dans des conditions seches, qu'un groupe de chercheurs du CanmetENERGIE avaient lance, en 2000, un programme de R & D. Dans le cadre de programme un outil de simulation des evaporateurs au CO2 a ete developpe et un banc d'essai contenant une boucle secondaire de refrigeration utilisant le CO2 comme refrigerant a ete construit. Comme continuite de ce travail de recherche, en 2006 ce meme groupe de recherche a lance un nouveau projet qui consiste a faire une etude theorique et experimentale des evaporateurs au CO2 operants dans des conditions de givrage. Et, c'est exactement dans le cadre de ce projet que se positionne ce travail de these. Ce travail de recherche a ete entrepris pour mieux comprendre le comportement thermique et hydrodynamique des serpentins fonctionnant dans des conditions de givrage, l'effet des circuits de refrigerant ainsi que celui des parametres geometriques et d'operation. Pour cela, un travail theorique supporte par une etude experimentale a ete effectue

  19. An approach to automated chromosome analysis; Etudes pour une methode d'automatisation des analyses chromosomiques

    Energy Technology Data Exchange (ETDEWEB)

    Le Go, Roland

    1972-05-03

    d'une automatisation des differentes etapes de l'analyse chromosomique. Il est divise en trois tomes dont la matiere est decrite ci-apres. Dans le tome 1 est decrite l'etude d'un selecteur automatique de metaphases. Cet appareil doit realiser au cours du scanning d'une preparation, un processus de decision aboutissant a rejeter toutes images ininteressantes et a conserver les images pertinentes (bonnes metaphases). Ce probleme a ete aborde au moyen d'une etude sur ordinateur par un programme de simulation. La realisation de ce programme a permis d'etablir des algorithmes de selection dont la replique pourra etre realisee dans des circuits logiques electroniques. Dans le tome 2 est traite le probleme de l'automatisation de l'etude morphologique des chromosomes presents dans une metaphase. Cette automatisation necessite le traitement des photographies de metaphases par un appareil convertisseur optique-numerique qui extrait l'information-image et la transcrit sous la forme d'un fichier numerique. Ce fichier comporte pour une image de metaphase, environ 200 000 valeurs de gris, codees selon une echelle a 16, 32 ou 64 ni veaux. Ce fichier numerique est traite par un programme de reconnaissance de forme, qui isole les chromosomes et en recherche les traits caracteristiques: sommets de bras et region centromerique, dans le but d'obtenir des mensurations equivalentes aux longueurs des quatre bras. Le tome 3 etudie un programme d'etablissement automatique du caryotype humain, par appariement optimise des chromosomes. Les donnees proviennent de la numerisation directe des longueurs de bras, effectuee au moyen d'un lecteur digital BENSON. Le programme etablit une liste des appariements, un document graphique imprime representant les paires constituees, dans l'espace: longueur - index centromerique; enfin un document graphique obtenu sur traceur BENSON dans lequel l'auteur donne une representation personnelle des chromosomes, sous forme de croix a bras orthogonaux, dont chaque

  20. Pegase: safety studies - experimental study of burn-out risks in transient operation; Pegase: etude de surete - etude experimentale des risques de burn out en regime transitoire

    Energy Technology Data Exchange (ETDEWEB)

    Vernier, P [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1968-07-01

    canal chaud se met en etat de calefaction au bout de 0.1 s et que sa temperature atteint 500 C en 0.8 s. Les regimes hydrodynamiques rencontres dans les canaux apres l'accident sont des regimes d'expulsion periodiques de periodes courtes 0.2 a 0.5 s, caracteristiques de l'ebullition a basse pression. L'etude en regime permanent de la redistribution de debit dans un by-pass a donne des flux PHI{sub R} de redistribution de 190 W/cm{sup 2} pour une vitesse de 4.5 m/s a 50 C et de 175 W/cm{sup 2} a 60 C. Ces valeurs sont a majorer de 25 pour cent pour une vitesse de 6 m/s. On a montre la distinction a faire entre flux critique PHI{sub C} en regime periodique d'expulsion et flux de redistribution PHI{sub R} en regime permanent. (auteur)

  1. MixtureTree annotator: a program for automatic colorization and visual annotation of MixtureTree.

    Directory of Open Access Journals (Sweden)

    Shu-Chuan Chen

    Full Text Available The MixtureTree Annotator, written in JAVA, allows the user to automatically color any phylogenetic tree in Newick format generated from any phylogeny reconstruction program and output the Nexus file. By providing the ability to automatically color the tree by sequence name, the MixtureTree Annotator provides a unique advantage over any other programs which perform a similar function. In addition, the MixtureTree Annotator is the only package that can efficiently annotate the output produced by MixtureTree with mutation information and coalescent time information. In order to visualize the resulting output file, a modified version of FigTree is used. Certain popular methods, which lack good built-in visualization tools, for example, MEGA, Mesquite, PHY-FI, TreeView, treeGraph and Geneious, may give results with human errors due to either manually adding colors to each node or with other limitations, for example only using color based on a number, such as branch length, or by taxonomy. In addition to allowing the user to automatically color any given Newick tree by sequence name, the MixtureTree Annotator is the only method that allows the user to automatically annotate the resulting tree created by the MixtureTree program. The MixtureTree Annotator is fast and easy-to-use, while still allowing the user full control over the coloring and annotating process.

  2. Toxicology of chemical mixtures: International perspective

    NARCIS (Netherlands)

    Feron, V.J.; Cassee, F.R.; Groten, J.P.

    1998-01-01

    This paper reviews major activities outside the United States on human health issues related to chemical mixtures. In Europe an international study group on combination effects has been formed and has started by defining synergism and antagonism. Successful research programs in Europe include the

  3. Collective dynamics in dense fluid mixtures

    International Nuclear Information System (INIS)

    Sinha, S.

    1992-01-01

    This thesis deals with the short wavelength collective dynamics of dense binary fluid mixtures. The analysis shows that at the level of linearized generalized hydrodynamics, the longitudinal modes of the system separates essentially into two parts - one involves the coupling of partial density fluctuations of the two species and the other involves coupling of longitudinal momentum and temperature fluctuations. The authors have shown that the coupling of longitudinal momentum and temperature fluctuations leads to an adequate description of sound propagation in such systems. In particular, they show that structural disorder controls the trapping of sound waves in dense mixtures. The coupling of the partial density fluctuations of the two species leads to a simple description of the partial dynamic structure factors. The results are in agreement with the molecular dynamics simulations of soft sphere mixtures. The partial density fluctuations are the slowest decaying fluctuations on molecular length scales and it turns out that nonlinear coupling of these slow modes leads to important corrections to the long time behavior of the time correlation functions determining the shear viscosity in dense mixtures

  4. The Coffee-Milk Mixture Problem Revisited

    Science.gov (United States)

    Marion, Charles F.

    2015-01-01

    This analysis of a problem that is frequently posed at professional development workshops, in print, and on the Web--the coffee-milk mixture riddle--illustrates the timeless advice of George Pólya's masterpiece on problem solving in mathematics, "How to Solve It." In his book, Pólya recommends that problems previously solved and put…

  5. Modelling interactions in grass-clover mixtures

    NARCIS (Netherlands)

    Nassiri Mahallati, M.

    1998-01-01

    The study described in this thesis focuses on a quantitative understanding of the complex interactions in binary mixtures of perennial ryegrass (Lolium perenne L.) and white clover (Trifolium repens L.) under cutting. The first part of the study describes the dynamics of growth, production

  6. Predicting diffusivities in dense fluid mixtures

    Directory of Open Access Journals (Sweden)

    C. DARIVA

    1999-09-01

    Full Text Available In this work the Enskog solution of the Boltzmann equation, as corrected by Speedy, together with the Weeks-Chandler-Andersen (WCA perturbation theory of liquids is employed in correlating and predicting self-diffusivities of dense fluids. Afterwards this theory is used to estimate mutual diffusion coefficients of solutes at infinite dilution in sub and supercritical solvents. We have also investigated the behavior of Fick diffusion coefficients in the proximity of a binary vapor-liquid critical point since this subject is of great interest for extraction purposes. The approach presented here, which makes use of a density and temperature dependent hard-sphere diameter, is shown to be excellent for predicting diffusivities in dense pure fluids and fluid mixtures. The calculations involved highly nonideal mixtures as well as systems with high molecular asymmetry. The predicted diffusivities are in good agreement with the experimental data for the pure and binary systems. The methodology proposed here makes only use of pure component information and density of mixtures. The simple algebraic relations are proposed without any binary adjustable parameters and can be readily used for estimating diffusivities in multicomponent mixtures.

  7. Two-Microphone Separation of Speech Mixtures

    DEFF Research Database (Denmark)

    Pedersen, Michael Syskind; Wang, DeLiang; Larsen, Jan

    2008-01-01

    combined, independent component analysis (ICA) and binary time–frequency (T–F) masking. By estimating binary masks from the outputs of an ICA algorithm, it is possible in an iterative way to extract basis speech signals from a convolutive mixture. The basis signals are afterwards improved by grouping...

  8. Wind Integration into Various Generation Mixtures

    NARCIS (Netherlands)

    Maddaloni, J.D.; Rowe, A.M.; Kooten, van G.C.

    2009-01-01

    A load balance model is used to quantify the economic and environmental effects of integrating wind power into three typical generation mixtures. System operating costs over a specified period are minimized by controlling the operating schedule of the existing power generating facilities for a range

  9. Modeling text with generalizable Gaussian mixtures

    DEFF Research Database (Denmark)

    Hansen, Lars Kai; Sigurdsson, Sigurdur; Kolenda, Thomas

    2000-01-01

    We apply and discuss generalizable Gaussian mixture (GGM) models for text mining. The model automatically adapts model complexity for a given text representation. We show that the generalizability of these models depends on the dimensionality of the representation and the sample size. We discuss...

  10. Semiparametric mixtures in case-controlstudies

    NARCIS (Netherlands)

    Murphy, S.A.; van der Vaart, A.W.

    2001-01-01

    We consider likelihood based inference in a class of logistic models for case-control studies with a partially observed covariate. The likelihood is a combination of a nonparametric mixture, a parametric likelihood, and an empirical likelihood. We prove the asymptotic normality of the maximum

  11. Thermodynamic modeling of CO2 mixtures

    DEFF Research Database (Denmark)

    Bjørner, Martin Gamel

    Knowledge of the thermodynamic properties and phase equilibria of mixtures containing carbon dioxide (CO2) is important in several industrial processes such as enhanced oil recovery, carbon capture and storage, and supercritical extractions, where CO2 is used as a solvent. Despite this importance...

  12. Pool Boiling of Hydrocarbon Mixtures on Water

    Energy Technology Data Exchange (ETDEWEB)

    Boee, R.

    1996-09-01

    In maritime transport of liquefied natural gas (LNG) there is a risk of spilling cryogenic liquid onto water. The present doctoral thesis discusses transient boiling experiments in which liquid hydrocarbons were poured onto water and left to boil off. Composition changes during boiling are believed to be connected with the initiation of rapid phase transition in LNG spilled on water. 64 experimental runs were carried out, 14 using pure liquid methane, 36 using methane-ethane, and 14 using methane-propane binary mixtures of different composition. The water surface was open to the atmosphere and covered an area of 200 cm{sup 2} at 25 - 40{sup o}C. The heat flux was obtained by monitoring the change of mass vs time. The void fraction in the boiling layer was measured with a gamma densitometer, and a method for adapting this measurement concept to the case of a boiling cryogenic liquid mixture is suggested. Significant differences in the boil-off characteristics between pure methane and binary mixtures revealed by previous studies are confirmed. Pure methane is in film boiling, whereas the mixtures appear to enter the transitional boiling regime with only small amounts of the second component added. The results indicate that the common assumption that LNG will be in film boiling on water because of the high temperature difference, may be questioned. Comparison with previous work shows that at this small scale the results are influenced by the experimental apparatus and procedures. 66 refs., 76 figs., 28 tabs.

  13. 16 CFR 1500.5 - Hazardous mixtures.

    Science.gov (United States)

    2010-01-01

    ..., flammable, sensitizing, or pressure-generating properties of a substance from what is known about its... Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT REGULATIONS HAZARDOUS SUBSTANCES AND ARTICLES; ADMINISTRATION AND ENFORCEMENT REGULATIONS § 1500.5 Hazardous mixtures...

  14. Optimal designs for linear mixture models

    NARCIS (Netherlands)

    Mendieta, E.J.; Linssen, H.N.; Doornbos, R.

    1975-01-01

    In a recent paper Snee and Marquardt [8] considered designs for linear mixture models, where the components are subject to individual lower and/or upper bounds. When the number of components is large their algorithm XVERT yields designs far too extensive for practical purposes. The purpose of this

  15. Meso Mechanical Analysis of AC Mixture Response

    NARCIS (Netherlands)

    Woldekidan, M.F.; Huurman, M.; Vaccari, E.; Poot, M.

    2012-01-01

    Ongoing research into performance modeling of Asphalt Concrete (AC) mixtures using meso mechanics approaches is being undertaken at Delft University of Technology (TUD). The approach has already been successfully employed for evaluating the long term performance of porous asphalt concrete. The work

  16. Optimal designs for linear mixture models

    NARCIS (Netherlands)

    Mendieta, E.J.; Linssen, H.N.; Doornbos, R.

    1975-01-01

    In a recent paper Snee and Marquardt (1974) considered designs for linear mixture models, where the components are subject to individual lower and/or upper bounds. When the number of components is large their algorithm XVERT yields designs far too extensive for practical purposes. The purpose of

  17. Concrete mixture characterization. Cementitious barriers partnership

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Protiere, Yannick [SIMCO Technologies, Inc., Quebec (Canada)

    2014-12-01

    This report summarizes the characterization study performed on two concrete mixtures used for radioactive waste storage. Both mixtures were prepared with approximately 425 kg of binder. The testing protocol mostly focused on determining the transport properties of the mixtures; volume of permeable voids (porosity), diffusion coefficients, and water permeability were evaluated. Tests were performed after different curing durations. In order to obtain data on the statistical distribution of transport properties, the measurements after 2 years of curing were performed on 10+ samples. Overall, both mixtures exhibited very low tortuosities and permeabilities, a direct consequence of their low water-to-binder ratio and the use of supplementary cementitious materials. The data generated on 2-year old samples showed that porosity, tortuosity and permeability follow a normal distribution. Chloride ponding tests were also performed on test samples. They showed limited chloride ingress, in line with measured transport properties. These test results also showed that both materials react differently with chloride, a consequence of the differences in the binder chemical compositions.

  18. Bayesian mixture analysis for metagenomic community profiling.

    Science.gov (United States)

    Morfopoulou, Sofia; Plagnol, Vincent

    2015-09-15

    Deep sequencing of clinical samples is now an established tool for the detection of infectious pathogens, with direct medical applications. The large amount of data generated produces an opportunity to detect species even at very low levels, provided that computational tools can effectively profile the relevant metagenomic communities. Data interpretation is complicated by the fact that short sequencing reads can match multiple organisms and by the lack of completeness of existing databases, in particular for viral pathogens. Here we present metaMix, a Bayesian mixture model framework for resolving complex metagenomic mixtures. We show that the use of parallel Monte Carlo Markov chains for the exploration of the species space enables the identification of the set of species most likely to contribute to the mixture. We demonstrate the greater accuracy of metaMix compared with relevant methods, particularly for profiling complex communities consisting of several related species. We designed metaMix specifically for the analysis of deep transcriptome sequencing datasets, with a focus on viral pathogen detection; however, the principles are generally applicable to all types of metagenomic mixtures. metaMix is implemented as a user friendly R package, freely available on CRAN: http://cran.r-project.org/web/packages/metaMix sofia.morfopoulou.10@ucl.ac.uk Supplementary data are available at Bionformatics online. © The Author 2015. Published by Oxford University Press.

  19. Measurement and correlation of critical properties for binary mixtures and ternary mixtures containing gasoline additives

    International Nuclear Information System (INIS)

    Wang, Lipu; Han, Kewei; Xia, Shuqian; Ma, Peisheng; Yan, Fangyou

    2014-01-01

    Highlights: • A high-pressure view cell was used to measure the critical properties of mixtures. • Three binary mixtures’ and three ternary mixtures’ critical properties were reported. • The experimental data of each system covered the whole mole fraction range. • The critical properties of the ternary mixtures were predicted with the PR–WS model. • Empirical equations were used to correlate the experimental results. - Abstract: The critical properties of three binary mixtures and three ternary mixtures containing gasoline additives (including methanol + 1-propanol, heptane + ethanol, heptane + 1-propanol, methanol + 1-propanol + heptane, methanol + 1-propanol + methyl tert-butyl ether (MTBE), and ethanol + heptane + MTBE) were determined by a high-pressure cell. All the critical lines of binary mixtures belong to the type I described by Scott and van Konynenburg. The system of methanol + 1-propanol showed little non-ideal behavior due to their similar molecular structures. The heptane + ethanol and heptane + 1-propanol systems showed visible non-ideal behavior for their great differences in molecular structure. The Peng–Robinson equation of state combined with the Wong–Sandler mixing rule (PR–WS) was applied to correlate the critical properties of binary mixtures. The critical points of the three ternary mixtures were predicted by the PR–WS model with the binary interaction parameters using the procedure proposed by Heidemann and Khalil. The predicted critical temperatures were in good agreement with the experimental values, while the predicted critical pressures differed from the measured values. The experimental values of binary mixtures were fitted well with the Redlich–Kister equation. The critical properties of ternary mixtures were correlated with the Cibulka’s equation, and the critical surfaces were plotted using the Cibulka’s equations

  20. Experiments with Mixtures Designs, Models, and the Analysis of Mixture Data

    CERN Document Server

    Cornell, John A

    2011-01-01

    The most comprehensive, single-volume guide to conducting experiments with mixtures"If one is involved, or heavily interested, in experiments on mixtures of ingredients, one must obtain this book. It is, as was the first edition, the definitive work."-Short Book Reviews (Publication of the International Statistical Institute)"The text contains many examples with worked solutions and with its extensive coverage of the subject matter will prove invaluable to those in the industrial and educational sectors whose work involves the design and analysis of mixture experiments."-Journal of the Royal S

  1. Study of the dynamic behaviour of the reactor Rapsodie; Etude du comportement dynamique de la pile rapsodie

    Energy Technology Data Exchange (ETDEWEB)

    Abdon, R; Chaigne, M [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1964-07-01

    . The investigation of the control, carried out on analog computer, served to determine the different possible means of starting and changing the conditions of the reactor as well as its automatic control. The calculations were examined in the totality by the construction of a training simulator composed of a board similar to the control board of the reactor, all of whose commands (reactivity and flows) work on an analogue computer which resolves in the real time the dynamic equations of the reactor and which reproduces simultaneously all the parameters representing the state of the installation (power, period, temperatures, etc. ) in the case of various incidents as well as under normal conditions of functioning. (authors) [French] On sait que le developpement des reacteurs surgenerateurs a neutrons rapides pose des problemes nouveaux d'une part dans les domaines mecanique et thermique et d'autre part en ce qui concerne leur comportement dynamique et leur surete. La pile RAPSODIE a ete l'objet de tres nombreuses etudes dynamiques effectuees sur machines analogiques et digitales, pour deux versions du combustible (metal et oxyde). Apres elaboration des modeles mathematiques representatifs de l'ensemble de l'installation (bloc pile et circuit de refroidissement) tant du point de vue neutronique que du point de vue thermodynamique, on a mis au point les schemas analogiques et les codes digitaux utilisables pour mener a bien les simulations d'incidents, de conduite et de stabilite du reacteur. On s'est attache, par rapport aux methodes habituelles a obtenir une precision plus grande, par un decoupage en zones plus fines, par l'emploi de formulations plus representatives du systeme reel, voire solubles analytiquement. Les etudes d'incidents ont ete effectuees par voie analogique pour l'ensemble de l'installation et par voie digitale pour l'etude du bloc pile seul ou de l'installation fonctionnant avec un seul circuit thermique. Un programme complementaire special - qui, a

  2. The study of neutron transport by oscillation method; Etude du transport des neutrons par la methode de modulation

    Energy Technology Data Exchange (ETDEWEB)

    Raievski, V

    1959-07-01

    The oscillation method is of very general use for studying the behavior of thermal neutrons in media. The main experiments are described and a general theory of them is given. This theory, which is presented in the first part, is established using the two-group approximation which has proved its efficiency in the case of thermal neutron piles. The validity of the two-group approximation is recalled. This allows definition of the meaning of the parameters used in the theory and which are measured in these experiments. The experiments carried out by this method are described, especially those performed at the Centre d'Etudes Nucleaires de Saclay where the method has been extensively used. These experiments are interpreted by means of the general theory given previously. In this way, the identity of parameters measured by this method and those given by the theory is proved. This is particularly conclusive is the case of the mean life of neutrons in a pile. (author) [French] La methode de modulation est un procede tres general d'etude des proprietes neutroniques des milieux contenant des neutrons thermiques. Le present rapport a pour but de decrire les principales de ces experiences et d'en donner une theorie generale. Cette theorie, exposee dans la premiere partie, est etablie dons le cadre de l'approximation a deux groupes de vitesse qui a prouve son efficacite dons le cas des piles a neutrons thermiques. Le domaine de validite de l'approximation a deux groupes est rappele au debut, ce qui permet de definir avec precision la signification des parametres qui entrent dons la theorie et qui font l'objet de ces mesures. La deuxieme partie decrit les experiences realisees, en particulier celles effectuees au Centre d'Etudes Nucleaires de Saclay ou la methode a ete considerablement developpee. Ces experiences sont interpretees dans le cadre de la theorie generale exposee precedemment. On prouve ainsi l'identite des parametres mesures par cette methode et de ceux figurant

  3. The Formation of Haze During the Rise of Oxygen in the Atmosphere of the Early Earth

    Science.gov (United States)

    Horst, S. M.; Jellinek, M.; Pierrehumbert, R.; Tolbert, M. A.

    2014-12-01

    also provide a wealth of organic material to the surface. Photochemical hazes are abundant in reducing atmospheres, such as the N2/CH4 atmosphere of Titan, but are unlikely to form in oxidizing atmospheres, such as the N2/O2 atmosphere of present day Earth. However, information about haze formation in mildly oxidizing atmospheres is lacking. Understanding haze formation in mildly oxidizing atmospheres is necessary for models that wish to investigate the atmosphere of the Early Earth as O2 first appeared and then increased in abundance. Previous studies of the atmosphere of the Early Earth have focused on haze formation in N2/CO2/CH4 atmospheres. In this work, we experimentally investigate the effect of the addition of O2 on the formation and composition of aerosols. Using a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) (see e.g. [1]) we have obtained in situ composition measurements of aerosol particles produced in N2/CO2/CH4/O2 gas mixtures subjected to FUV radiation (deuterium lamp, 115-400 nm) for a range of initial CO2/CH4/O2 mixing ratios. In particular, we studied the effect of O2 ranging from 2 ppm to 2%. The particles were also investigated using a Scanning Mobility Particle Sizer (SMPS), which measures particle size, number density and mass loading. A comparison of the composition of the aerosols will be presented. The effect of variation of O2 mixing ratio on aerosol production, size, and composition will also be discussed. [1] Trainer, M.G., et al. (2012) Astrobiology, 12, 315-326.

  4. Properties of Direct Coal Liquefaction Residue Modified Asphalt Mixture

    Directory of Open Access Journals (Sweden)

    Jie Ji

    2017-01-01

    Full Text Available The objectives of this paper are to use Direct Coal Liquefaction Residue (DLCR to modify the asphalt binders and mixtures and to evaluate the performance of modified asphalt mixtures. The dynamic modulus and phase angle of DCLR and DCLR-composite modified asphalt mixture were analyzed, and the viscoelastic properties of these modified asphalt mixtures were compared to the base asphalt binder SK-90 and Styrene-Butadiene-Styrene (SBS modified asphalt mixtures. The master curves of the asphalt mixtures were shown, and dynamic and viscoelastic behaviors of asphalt mixtures were described using the Christensen-Anderson-Marasteanu (CAM model. The test results show that the dynamic moduli of DCLR and DCLR-composite asphalt mixtures are higher than those of the SK-90 and SBS modified asphalt mixtures. Based on the viscoelastic parameters of CAM models of the asphalt mixtures, the high- and low-temperature performance of DLCR and DCLR-composite modified asphalt mixtures are obviously better than the SK-90 and SBS modified asphalt mixtures. In addition, the DCLR and DCLR-composite modified asphalt mixtures are more insensitive to the frequency compared to SK-90 and SBS modified asphalt mixtures.

  5. Study of the contamination of live-stock during periods of radio-active fall-out (1963); Essai d'etude de la contamination du cheptel en periode de retombees radioactives (1963)

    Energy Technology Data Exchange (ETDEWEB)

    Michon, G; Jeanmaire, L [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1963-07-01

    The authors have tried, during the radioactive period corresponding, to the nuclear tests of the autumn 1961, to follow under natural conditions the contamination of a herd of cattle made up 9 cows and 7 calves. The observations concern I{sup 131}, which was studied in particular, and the mixture of fission products. As far as the excretion of iodine in milk is concerned, the equilibrium is established slowly and the amount found in the milk is about 1 per cent of the daily intake. This figure is lower than those based on experimental studies (given in the literature). For the mixture of products, only a small number of elements is metabolised. The fraction found in 1 kilo of liver is about 5 x 10{sup -5} of the amount of Zr-Nb taker up per day, and about 4 x 10{sup -4} of the daily intake of Ru. These elements are not found afterwards in muscle. (authors) [French] Les auteurs ont tente pendant la periode de retombees consecutives aux tirs nucleaires de l'automne 1961 de suivre dans des conditions naturelles la contamination d'un troupeau de bovins constitue de 9 vaches et 7 veaux. Les observations portent sur l'{sup 131}I plus particulierement etudie et sur le melange des produits de fission. En ce qui concerne l'excretion d'iode dans le lait l'equilibre s'etablit lentement et la quantite retrouvee dans un litre est de l'ordre de 1 pour cent de la quantite ingeree journellement. Cette valeur est inferieure a celles trouvees dans la litterature et resultant d'etudes experimentales. En ce qui concerne le melange de produits un petit nombre d'elements seulement sont metabolises La fraction que l'on retrouve dans un kilo de foie est de l'ordre de 5.10{sup -5} de la quantite de Zr-Nb ingeree par jour et de l'ordre de 4.10{sup -4} de la quantite de Ru ingeree par jour. Ces elements ne se retrouvent pas dans le muscle. (auteurs)

  6. Randomized control trial for the assessment of the anti-albuminuric effects of topiroxostat in hyperuricemic patients with diabetic nephropathy (the ETUDE study).

    Science.gov (United States)

    Kato, Sawako; Ando, Masahiko; Mizukoshi, Toshihiro; Nagata, Takanobu; Katsuno, Takayuki; Kosugi, Tomoki; Tsuboi, Naotake; Maruyama, Shoichi

    2016-05-01

    Proteinuria is an established risk factor for diabetic nephropathy. Recent studies indicate that some xanthine oxidase inhibitors have a renoprotective effect. The aim of this study was to assess whether topiroxostat reduces albuminuria in hyperuricemic patients with diabetic nephropathy and overt proteinuria. The ETUDE study is an ongoing 24-week, multicenter, open-label, randomized (1:1), parallel group study involving hyperuricemic patients with diabetic nephropathy (estimated glomerular filtration rate [eGFR] ≥ 20 mL/min/1.73 m(2)) and overt proteinuria (0.3 ≤ urine protein to creatinine ratio (UPCR) ETUDE trial is the first randomized controlled study of topiroxostat in hyperuricemic patients with diabetic nephropathy and overt proteinuria. We will clarify the pleiotropic function of topiroxostat including an anti-albumiuric effect as well as its effects on safely decreasing serum uric acid levels.

  7. Equivalence of truncated count mixture distributions and mixtures of truncated count distributions.

    Science.gov (United States)

    Böhning, Dankmar; Kuhnert, Ronny

    2006-12-01

    This article is about modeling count data with zero truncation. A parametric count density family is considered. The truncated mixture of densities from this family is different from the mixture of truncated densities from the same family. Whereas the former model is more natural to formulate and to interpret, the latter model is theoretically easier to treat. It is shown that for any mixing distribution leading to a truncated mixture, a (usually different) mixing distribution can be found so that the associated mixture of truncated densities equals the truncated mixture, and vice versa. This implies that the likelihood surfaces for both situations agree, and in this sense both models are equivalent. Zero-truncated count data models are used frequently in the capture-recapture setting to estimate population size, and it can be shown that the two Horvitz-Thompson estimators, associated with the two models, agree. In particular, it is possible to achieve strong results for mixtures of truncated Poisson densities, including reliable, global construction of the unique NPMLE (nonparametric maximum likelihood estimator) of the mixing distribution, implying a unique estimator for the population size. The benefit of these results lies in the fact that it is valid to work with the mixture of truncated count densities, which is less appealing for the practitioner but theoretically easier. Mixtures of truncated count densities form a convex linear model, for which a developed theory exists, including global maximum likelihood theory as well as algorithmic approaches. Once the problem has been solved in this class, it might readily be transformed back to the original problem by means of an explicitly given mapping. Applications of these ideas are given, particularly in the case of the truncated Poisson family.

  8. Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique

    OpenAIRE

    Kvítek, Zdeněk

    2010-01-01

    Etude de la transition ferroelectrique-ferroelastique du KD2PO4 forme du front de phase en fonction du gradient thermique The thesis explores complex process of first order transition of KD2PO4 crystal from tetragonal phase to ferroelectric - ferroelastic orthorhombic phase and back at temperature 209 K. The experimental set up of nitrogeneous cryostat allowes temperature and temperature gradient variations during simultaneous three axes optical sample observations, dielectric measurements. T...

  9. Point-of-care ultrasonography adoption in Canada: using diffusion theory and the Evaluation Tool for Ultrasound skills Development and Education (ETUDE).

    Science.gov (United States)

    Woo, Michael Y; Frank, Jason R; Lee, A Curtis

    2014-09-01

    Point-of-care ultrasonography (PoCUS) first appeared in the 1980s in North America, but the extent of the diffusion of its adoption is unknown. We characterized early PoCUS adoption by emergency physicians in Canada and its barriers to use using Rogers' diffusion of innovations theory. We developed a questionnaire based on a pilot study and literature review to assess past, current, and potential use of PoCUS and potential barriers to adoption. A Dillman technique for electronic surveys was used for dissemination. Using Rogers' diffusion of innovations theory, we developed and validated the Evaluation Tool for Ultrasound skills Development and Education (ETUDE). ETUDE scores allowed categorization of respondents into innovators, early adopters, majority, and nonadopters. Descriptive statistics, correlations, and χ² statistics were used to analyze the data. The 296 respondents (36.4% of 814 surveyed) had a median age of 40 and were 72.5% male. Adoption scores using ETUDE revealed nonadopters (18.8%), majority (28.7%), early adopters (34.5%), and innovators (18.0%). Respondents endorsed "always" using PoCUS currently and in the future for focused assessment with sonography in trauma (FAST) (current 41.8%/future 88.4%), first trimester pregnancy (current 23.3%/future 73.7%), suspected abdominal aortic aneurysm (current 32.7%/future 92.6%), basic cardiac indications (current 30.7%/future 87.5%), and central venous catheterization (current 17.0%/future 80.3%). Several barriers to PoCUS were identified for part-time emergency physicians and those working in inner-city/urban/suburban settings. This is the first study to determine the state of adoption and barriers to the introduction of PoCUS in Canadian emergency medicine practice. The novel validated ETUDE instrument should be used to evaluate the uptake of PoCUS over time.

  10. Theoretical study, and construction, of a spherical electrostatic beta spectrometer; Etude theorique et realisation d'un spectrometre beta electrostatique spherique

    Energy Technology Data Exchange (ETDEWEB)

    Moret, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1964-03-15

    After a literature survey showing the importance of an electrostatic spectrometer with spherical electrodes for studying disintegration processes, the theoretical characteristics of such an apparatus are derived (determination of the trajectory equations calculation of the transmission and of the resolving power the case of a point source and of an extended source). The apparatus built as a result of these calculations is described. The electrostatic field distribution outside the electrodes is derived. As well as giving electron spectra ({beta} disintegration and conversion electrons) the apparatus make s it possible to study e-{gamma}, e-{beta}, e-e-{gamma} and e-e-{beta} coincidences. In the last part are given experimental characteristics and the results of the first measurements made on conversion electron spectra ({sup 161}Tb, {sup 151}Pm, {sup 155}Eu) and on coincidences ({sup 170}Tm) using this spectrometer. (author) [French] Apres une etude bibliographique montrant l'interet que presente un spectrometre electrostatique a electrodes spheriques pour l'etude des schemas de desintegration, l'auteur etablit les caracteristiques theoriques d'un tel appareil (determination de l'equation des trajectoires calcul de la transmission et du pouvoir de resolution cas d'une source ponctuelle et d'une source etendue). On decrit l'appareil realise d'apres ces calculs. On etablit la repartition du champ electrostatique a l'exterieur des electrodes. Outre le trace des spectres d'electrons (desintegration {beta} et electrons de conversion), l'appareil permet l'etude de coincidences e-{gamma}, e-{beta}, e-e-{gamma} and e-e-{beta}. Dans la derniere partie, sont donnees les caracteristiques experimentales et les premieres etudes de spectres d'electrons de conversion ({sup 161}Tb, {sup 151}Pm, {sup 155}Eu) et de coincidences ({sup 170}Tm) faites a l'aide de ce spectrometre. (auteur)

  11. Experimental study of contamination by inhalation of radioactive iodine aerosols. Biological balance; Etude experimentale de la contamination par inhalation d'aerosols d'iode radioactif bilan biologique

    Energy Technology Data Exchange (ETDEWEB)

    Marble, G [Commissariat a l' Energie Atomique, 92 - Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1968-07-01

    Several articles have been published concerning research into contamination produced by inhalation of radioactive iodine aerosols in monkeys. Results dealing with the biological balance of this contamination are presented and discussed in this report. (author) [French] L'etude experimentale de la contamination par inhalation d'aerosols d'iode radioactif effectuee chez le singe a fait l'objet de plusieurs publications. Les resultats concernant le bilan biologique de cette contamination sont presentes et discutes dans ce rapport. (auteur)

  12. Direct Importance Estimation with Gaussian Mixture Models

    Science.gov (United States)

    Yamada, Makoto; Sugiyama, Masashi

    The ratio of two probability densities is called the importance and its estimation has gathered a great deal of attention these days since the importance can be used for various data processing purposes. In this paper, we propose a new importance estimation method using Gaussian mixture models (GMMs). Our method is an extention of the Kullback-Leibler importance estimation procedure (KLIEP), an importance estimation method using linear or kernel models. An advantage of GMMs is that covariance matrices can also be learned through an expectation-maximization procedure, so the proposed method — which we call the Gaussian mixture KLIEP (GM-KLIEP) — is expected to work well when the true importance function has high correlation. Through experiments, we show the validity of the proposed approach.

  13. Bright solitons in Bose-Fermi mixtures

    International Nuclear Information System (INIS)

    Karpiuk, Tomasz; Brewczyk, Miroslaw; RzaPewski, Kazimierz

    2006-01-01

    We consider the formation of bright solitons in a mixture of Bose and Fermi degenerate gases confined in a three-dimensional elongated harmonic trap. The Bose and Fermi atoms are assumed to effectively attract each other whereas bosonic atoms repel each other. Strong enough attraction between bosonic and fermionic components can change the character of the interaction within the bosonic cloud from repulsive to attractive making thus possible the generation of bright solitons in the mixture. On the other hand, such structures might be in danger due to the collapse phenomenon existing in attractive gases. We show, however, that under some conditions (defined by the strength of the Bose-Fermi components attraction) the structures which neither spread nor collapse can be generated. For elongated enough traps the formation of solitons is possible even at the 'natural' value of the mutual Bose-Fermi ( 87 Rb- 40 K in our case) scattering length

  14. Solvatochromism of naringenin in aqueous alcoholic mixtures

    Directory of Open Access Journals (Sweden)

    Faraji Mohammad

    2016-01-01

    Full Text Available The spectral change of naringenin was studied by Uv-vis spectrophotometric method in binary mixtures of water with methanol, ethanol and 1-propanol at 25°C. The effect of solvent was investigated by analysis of electron transition energy at the maximum absorption wavelength as a function of Kamlet and Taft parameters of mixtures by means of linear solvation energy relationships. The nonlinear response of solvatochromism was explained based on solute-solvent and solvent-solvent interactions. The possible preferential solvation of naringenin by each of solvents was studied through a modified preferential solvation model which considers the hydrogen bonding interactions between the prior solvents due to solvent-solvent interactions. The preferential solvation parameters and local mole fraction distribution around the solute were calculated. Results indicate that naringenin prefers to be more solvated by the complex solvating species and organic solvents than water.

  15. Heavy-light fermion mixtures at unitarity

    Energy Technology Data Exchange (ETDEWEB)

    Gezerlis, Alexandros [Los Alamos National Laboratory; Carlson, Joseph [Los Alamos National Laboratory; Gandol, S [UNIV. ILL; Schmidt, E [ITALY

    2009-01-01

    We investigate fermion pairing in the unitary regime for a mass ratio corresponding to a {sup 6}Li-{sup 40}K mixture using quantum Monte Carlo methods. The ground-state energy and the average light- and heavy-particle excitation spectrum for the unpolarized superfluid state are nearly independent of the mass ratio. In the majority light system, the polarized superfluid is close to the energy of a phase separated mixture of nearly fully polarized normal and unpolarized superfluid. For a majority of heavy particles, we find an energy minimum for a normal state with a ratio of {approx}3:1 heavy to light particles. A slight increase in attraction to k{sub F}a{approx}2.5 yields a ground state energy of nearly zero for this ratio. A cold unpolarized system in a harmonic trap at unitarity should phase separate into three regions, with a shell of unpolarized superfluid in the middle.

  16. Structural properties of dendrimer-colloid mixtures

    International Nuclear Information System (INIS)

    Lenz, Dominic A; Blaak, Ronald; Likos, Christos N

    2012-01-01

    We consider binary mixtures of colloidal particles and amphiphilic dendrimers of the second generation by means of Monte Carlo simulations. By using the effective interactions between monomer-resolved dendrimers and colloids, we compare the results of simulations of mixtures stemming from a full monomer-resolved description with the effective two-component description at different densities, composition ratios, colloid diameters and interaction strengths. Additionally, we map the two-component system onto an effective one-component model for the colloids in the presence of the dendrimers. Simulations based on the resulting depletion potentials allow us to extend the comparison to yet another level of coarse graining and to examine under which conditions this two-step approach is valid. In addition, a preliminary outlook into the phase behavior of this system is given. (paper)

  17. NMRI Measurements of Flow of Granular Mixtures

    Science.gov (United States)

    Nakagawa, Masami; Waggoner, R. Allen; Fukushima, Eiichi

    1996-01-01

    We investigate complex 3D behavior of granular mixtures in shaking and shearing devices. NMRI can non-invasively measure concentration, velocity, and velocity fluctuations of flows of suitable particles. We investigate origins of wall-shear induced convection flow of single component particles by measuring the flow and fluctuating motion of particles near rough boundaries. We also investigate if a mixture of different size particles segregate into their own species under the influence of external shaking and shearing disturbances. These non-invasive measurements will reveal true nature of convecting flow properties and wall disturbance. For experiments in a reduced gravity environment, we will design a light weight NMR imager. The proof of principle development will prepare for the construction of a complete spaceborne system to perform experiments in space.

  18. Mixtures of maximally entangled pure states

    Energy Technology Data Exchange (ETDEWEB)

    Flores, M.M., E-mail: mflores@nip.up.edu.ph; Galapon, E.A., E-mail: eric.galapon@gmail.com

    2016-09-15

    We study the conditions when mixtures of maximally entangled pure states remain entangled. We found that the resulting mixed state remains entangled when the number of entangled pure states to be mixed is less than or equal to the dimension of the pure states. For the latter case of mixing a number of pure states equal to their dimension, we found that the mixed state is entangled provided that the entangled pure states to be mixed are not equally weighted. We also found that one can restrict the set of pure states that one can mix from in order to ensure that the resulting mixed state is genuinely entangled. Also, we demonstrate how these results could be applied as a way to detect entanglement in mixtures of the entangled pure states with noise.

  19. Sequential Estimation of Mixtures in Diffusion Networks

    Czech Academy of Sciences Publication Activity Database

    Dedecius, Kamil; Reichl, Jan; Djurić, P. M.

    2015-01-01

    Roč. 22, č. 2 (2015), s. 197-201 ISSN 1070-9908 R&D Projects: GA ČR(CZ) GP14-06678P Institutional support: RVO:67985556 Keywords : distributed estimation * mixture models * bayesian inference Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 1.661, year: 2015 http://library.utia.cas.cz/separaty/2014/AS/dedecius-0431479.pdf

  20. Nitrocarburizing in ammonia-hydrocarbon gas mixtures

    DEFF Research Database (Denmark)

    Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

    2011-01-01

    The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammonia-propene-hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

  1. Nitrocarburising in ammonia-hydrocarbon gas mixtures

    DEFF Research Database (Denmark)

    Pedersen, Hanne; Christiansen, Thomas; Somers, Marcel A. J.

    2010-01-01

    The present work investigates the possibility of nitrocarburising in ammonia-acetylene-hydrogen and ammoniapropene- hydrogen gas mixtures, where unsaturated hydrocarbon gas is the carbon source during nitrocarburising. Consequently, nitrocarburising is carried out in a reducing atmosphere...... microscopy and X-ray diffraction analysis. It is shown that the use of unsaturated hydrocarbon gas in nitrocarburising processes is a viable alternative to traditional nitrocarburising methods....

  2. Text document classification based on mixture models

    Czech Academy of Sciences Publication Activity Database

    Novovičová, Jana; Malík, Antonín

    2004-01-01

    Roč. 40, č. 3 (2004), s. 293-304 ISSN 0023-5954 R&D Projects: GA AV ČR IAA2075302; GA ČR GA102/03/0049; GA AV ČR KSK1019101 Institutional research plan: CEZ:AV0Z1075907 Keywords : text classification * text categorization * multinomial mixture model Subject RIV: BB - Applied Statistics, Operational Research Impact factor: 0.224, year: 2004

  3. Structure of cholesterol/ceramide monolayer mixtures

    DEFF Research Database (Denmark)

    Scheffer, L.; Solomonov, I.; Weygand, M.J.

    2005-01-01

    The structure of monolayers of cholesterol/ ceramide mixtures was investigated using grazing incidence x-ray diffraction, immunofluorescence, and atomic force microscopy techniques. Grazing incidence x-ray diffraction measurements showed the existence of a crystalline mixed phase of the two....... As ceramide incorporates the lipid backbone common to all sphingolipids, this arrangement may be relevant to the understanding of the molecular organization of lipid rafts....

  4. Studies of iron carbon alloys; Contribution a l'etude des alliages dilues de carbone dans le fer {alpha}

    Energy Technology Data Exchange (ETDEWEB)

    Anagnostopoulos, T [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1971-07-01

    Precipitation of carbon in {alpha} iron during a thermal treatment was followed using the magnetic after effect. A study was made of the influence of different parameters such as quenching speed, annealing rate, carbon concentration with or without impurity, irradiation effects. A transient sur-saturation occurs during dissolution of carbon in iron at 500 C. (author) [French] La precipitation du carbone dans le fer au cours d'un traitement thermique a ete suivie au moyen du trainage magnetique. L'etude de differents parametres tels que: vitesse de trempe, mode de recuit, concentration en carbone, presence d'impuretes, effet d'une irradiation, ont ete menes a bien. Un phenomene de sursaturation transitoire au cours de la remise en solution a 500 C a ete mis en evidence. (auteur)

  5. Dosimeter calibration facilities and methods at the Radiation Measurement Laboratory of the Centre d'etudes nucleaires, Grenoble

    International Nuclear Information System (INIS)

    Choudens, H. de; Herbaut, Y.; Haddad, A.; Giroux, J.; Rouillon, J.; CEA Centre d'Etudes Nucleaires de Grenoble, 38

    1975-01-01

    At the Centre d'etudes nucleaires, Grenoble, the Radiation Measurement Laboratory, which forms part of the Environmental Protection and Research Department, serves the entire Centre for purposes of dosimetry and the calibration of dose meters. The needs of radiation protection are such that one must have facilities for checking periodically the calibration of radiation-monitoring instruments and developing special dosimetry techniques. It was thought a good idea to arrange for the dosimetry and radiation protection team to assist other groups working at the Centre - in particular, the staff of the biology and radiobiology laboratories - and also bodies outside the framework of the French Commissariat a l'energie atomique. Thus, technical collaboration has been established with, for example, Grenoble's Centre hospitalier universitaire (university clinic), which makes use of the facilities and skills available at the Radiation Measurement Laboratory for solving special dosimetry problems. With the Laboratory's facilities it is possible to calibrate dose meters for gamma, beta and neutron measurements

  6. Some techniques for studying actomyosin by electron microscopy; Quelques techniques d'etude de l'actomyosine par microscopie electronique

    Energy Technology Data Exchange (ETDEWEB)

    Herzberg, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires. Departement de Biologie

    1967-07-01

    A method has been developed for shadowing using a platinum-carbon alloy; it has been applied to the study of the interaction of actomyosin with its substrate ATP. The results obtained seem to favour the hypothesis of a dissociation of the actomyosin into its two components: actin and myosin. Pictures have been obtained showing particles resembling non-polymerized myosin but no rigorous proof of this exists. (author) [French] Une methode d'ombrage par un alliage de platine et carbone a ete mise au point et appliquee a l'etude de l'interaction de l'actomyosine et de son substrat l'ATP. Les resultats obtenus semblent pencher en faveur de la these d'une dissociation de l'actomyosine en ses deux constituants: l'actine et la myosine. Des images ont ete obtenues montrant des particules dont l'identite avec la myosine non polymerisee reste a demontrer plus rigoureusement. (auteur)

  7. Cell for studying electron-adsorbed gas interactions; Cellule d'etudes des interactions electron-gaz adsorbe

    Energy Technology Data Exchange (ETDEWEB)

    Golowacz, H; Degras, D A [Commissariat a l' Energie Atomique, 91 - Saclay (France). Centre d' Etudes Nucleaires, Deptartement de Physique des Plasmas et de la Fusion Controlee, Service de Physique Appliquee, Service de Physique des Interractions Electroniques, Section d' Etude des Interactions Gaz-Solides

    1967-07-01

    The geometry and the technology of a cell used for investigations on electron-adsorbed gas interactions are described. The resonance frequencies of the surface ions which are created by the electron impact on the adsorbed gas are predicted by simplified calculations. The experimental data relative to carbon monoxide and neon are in good agreement with these predictions. (authors) [French] Les caracteristiques geometriques et technologiques generales d'une cellule d'etude des interactions entre un faisceau d'electrons et un gaz adsorbe sont donnees. Un calcul simplifie permet de prevoir les frequences de resonance des ions de surface crees par l'impact des electrons sur le gaz adsorbe. Les donnees experimentales sur l'oxyde de carbone et le neon confirment les previsions du calcul. (auteurs)

  8. Ethane-xenon mixtures under shock conditions

    Science.gov (United States)

    Flicker, Dawn; Magyar, Rudolph; Root, Seth; Cochrane, Kyle; Mattsson, Thomas

    2015-06-01

    Mixtures of light and heavy elements arise in inertial confinement fusion and planetary science. We present results on the physics of molecular scale mixing through a validation study of equation of state (EOS) properties. Density functional theory molecular dynamics (DFT/QMD) at elevated-temperature and pressure is used to obtain the properties of pure xenon, ethane, and various compressed mixture compositions along their principal Hugoniots. To validate the QMD simulations, we performed high-precision shock compression experiments using Sandia's Z-Machine. A bond tracking analysis of the simulations correlates the sharp rise in the Hugoniot curve with completion of dissociation in ethane. DFT-based simulation results compare well with experimental data and are used to provide insight into the dissociation as a function of mixture composition. Interestingly, we find that the compression ratio for complete dissociation is similar for ethane, Xe-ethane, polymethyl-pentene, and polystyrene, suggesting that a limiting compression exists for C-C bonded systems. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Company, Security Administration under contract DE-AC04-94AL85000.

  9. Method for separating gaseous mixtures of matter

    International Nuclear Information System (INIS)

    Schuster, E.; Kersting, A.

    1979-01-01

    Molecules to be separated from a mixture of matter of a chemical component are excited in a manner known per se by narrow-band light sources, and a chemical reaction partner for reacting with these molecules is admixed while supplied with energy by electromagnetic radiation or heating, and as additionally required for making chemical reactions possible. A method is described for separating gaseous mixtures of matter by exciting the molecules to be separated with laser radiation and causing the excited species to react chemically with a reaction partner. It may be necessary to supply additional energy to the reaction partner to make the chemical reaction possible. The method is applicable to the separation of hydrogen isotopes by the bromination of normal methanol in a mixture normal methanol and deuterated methanol; of uranium isotope by the reactions of UF 6 with SF 4 , SiCl 4 , HCl, or SO 2 ; and of boron isotopes by the reaction of BH 3 with NH 3

  10. Safety Testing of Ammonium Nitrate Based Mixtures

    Science.gov (United States)

    Phillips, Jason; Lappo, Karmen; Phelan, James; Peterson, Nathan; Gilbert, Don

    2013-06-01

    Ammonium nitrate (AN)/ammonium nitrate based explosives have a lengthy documented history of use by adversaries in acts of terror. While historical research has been conducted on AN-based explosive mixtures, it has primarily focused on detonation performance while varying the oxygen balance between the oxidizer and fuel components. Similarly, historical safety data on these materials is often lacking in pertinent details such as specific fuel type, particle size parameters, oxidizer form, etc. A variety of AN-based fuel-oxidizer mixtures were tested for small-scale sensitivity in preparation for large-scale testing. Current efforts focus on maintaining a zero oxygen-balance (a stoichiometric ratio for active chemical participants) while varying factors such as charge geometry, oxidizer form, particle size, and inert diluent ratios. Small-scale safety testing was conducted on various mixtures and fuels. It was found that ESD sensitivity is significantly affected by particle size, while this is less so for impact and friction. Thermal testing is in progress to evaluate hazards that may be experienced during large-scale testing.

  11. Method of separation of gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Berlin, M.A.; Potapov, V.F.; Potapova, M.S.

    1980-04-05

    Gas mixtures are separated in a rectification tower by repeated counterflow contact of the heated gas flow and cool condensate as the pressure drops in each stage of separation (StR) and when condensate is added from StR with lower pressure to the StR with higher pressure. In order to reduce energy consumption noncondensing gas in amounts of 5-15 percent by weight of the amount of incoming gases are added. Hydrocarbon or carbon dioxide gas can be used as the latter. Example. To separate natural gas of the Shatlyk deposit of composition, percent by mo1: C1 -- 94.960; C2 -- 4.260; C3 -- 0.200; C4 -- 0.08; C4+B -- 0.51. It is enriched with carbon dioxide gas in an amount of 10 percent by weight. Upon rectification of the enriched hydrocarbon mixture separation is achieved at lower pressures of the gas mixture and less cold. This leads to reduction of energy consumption by 10-12 percent.

  12. Shear of ordinary and elongated granular mixtures

    Science.gov (United States)

    Hensley, Alexander; Kern, Matthew; Marschall, Theodore; Teitel, Stephen; Franklin, Scott

    2015-03-01

    We present an experimental and computational study of a mixture of discs and moderate aspect-ratio ellipses under two-dimensional annular planar Couette shear. Experimental particles are cut from acrylic sheet, are essentially incompressible, and constrained in the thin gap between two concentric cylinders. The annular radius of curvature is much larger than the particles, and so the experiment is quasi-2d and allows for arbitrarily large pure-shear strains. Synchronized video cameras and software identify all particles and track them as they move from the field of view of one camera to another. We are particularly interested in the global and local properties as the mixture ratio of discs to ellipses varies. Global quantities include average shear rate and distribution of particle species as functions of height, while locally we investigate the orientation of the ellipses and non-affine events that can be characterized as shear transformational zones or possess a quadrupole signature observed previously in systems of purely circular particles. Discrete Element Method simulations on mixtures of circles and spherocylinders extend the study to the dynamics of the force network and energy dissipated as the system evolves. Supported by NSF CBET #1243571 and PRF #51438-UR10.

  13. Gaussian Process-Mixture Conditional Heteroscedasticity.

    Science.gov (United States)

    Platanios, Emmanouil A; Chatzis, Sotirios P

    2014-05-01

    Generalized autoregressive conditional heteroscedasticity (GARCH) models have long been considered as one of the most successful families of approaches for volatility modeling in financial return series. In this paper, we propose an alternative approach based on methodologies widely used in the field of statistical machine learning. Specifically, we propose a novel nonparametric Bayesian mixture of Gaussian process regression models, each component of which models the noise variance process that contaminates the observed data as a separate latent Gaussian process driven by the observed data. This way, we essentially obtain a Gaussian process-mixture conditional heteroscedasticity (GPMCH) model for volatility modeling in financial return series. We impose a nonparametric prior with power-law nature over the distribution of the model mixture components, namely the Pitman-Yor process prior, to allow for better capturing modeled data distributions with heavy tails and skewness. Finally, we provide a copula-based approach for obtaining a predictive posterior for the covariances over the asset returns modeled by means of a postulated GPMCH model. We evaluate the efficacy of our approach in a number of benchmark scenarios, and compare its performance to state-of-the-art methodologies.

  14. Robustifying Bayesian nonparametric mixtures for count data.

    Science.gov (United States)

    Canale, Antonio; Prünster, Igor

    2017-03-01

    Our motivating application stems from surveys of natural populations and is characterized by large spatial heterogeneity in the counts, which makes parametric approaches to modeling local animal abundance too restrictive. We adopt a Bayesian nonparametric approach based on mixture models and innovate with respect to popular Dirichlet process mixture of Poisson kernels by increasing the model flexibility at the level both of the kernel and the nonparametric mixing measure. This allows to derive accurate and robust estimates of the distribution of local animal abundance and of the corresponding clusters. The application and a simulation study for different scenarios yield also some general methodological implications. Adding flexibility solely at the level of the mixing measure does not improve inferences, since its impact is severely limited by the rigidity of the Poisson kernel with considerable consequences in terms of bias. However, once a kernel more flexible than the Poisson is chosen, inferences can be robustified by choosing a prior more general than the Dirichlet process. Therefore, to improve the performance of Bayesian nonparametric mixtures for count data one has to enrich the model simultaneously at both levels, the kernel and the mixing measure. © 2016, The International Biometric Society.

  15. Dye mixtures for ultrafast wavelength shifters

    Energy Technology Data Exchange (ETDEWEB)

    Gangopadhyay, S.; Liu, L.; Palsule, C.; Borst, W.; Wigmans, R. [Texas Tech Univ., Lubbock, TX (United States). Dept. of Physics; Barashkov, N. [Karpov Inst. of Physical Chemistry, Moscow (Russian Federation)

    1994-12-31

    Particle detectors based on scintillation processes have been used since the discovery of radium about 100 years ago. The fast signals that can be obtained with these detectors, although often considered a nice asset, were rarely essential for the success of experiments. However, the new generation of high energy particle accelerators require particle detectors with fast response time. The authors have produced fast wavelength shifters using mixtures of various Coumarin dyes with DCM in epoxy-polymers (DGEBA+HHPA) and measured the properties of these wavelength shifters. The particular mixtures were chosen because there is a substantial overlap between the emission spectrum of Coumarin and the absorption spectrum of DCM. The continuous wave and time-resolved fluorescence spectra have been studied as a function of component concentration to optimize the decay times, emission peaks and quantum yields. The mean decay times of these mixtures are in the range of 2.5--4.5 ns. The mean decay time increases with an increase in Coumarin concentration at a fixed DCM concentration or with a decrease in DCM concentration at a fixed Coumarin concentration. This indicates that the energy transfer is radiative at lower relative DCM concentrations and becomes non-radiative at higher DCM concentrations.

  16. Dye mixtures for ultrafast wavelength shifters

    International Nuclear Information System (INIS)

    Gangopadhyay, S.; Liu, L.; Palsule, C.; Borst, W.; Wigmans, R.

    1994-01-01

    Particle detectors based on scintillation processes have been used since the discovery of radium about 100 years ago. The fast signals that can be obtained with these detectors, although often considered a nice asset, were rarely essential for the success of experiments. However, the new generation of high energy particle accelerators require particle detectors with fast response time. The authors have produced fast wavelength shifters using mixtures of various Coumarin dyes with DCM in epoxy-polymers (DGEBA+HHPA) and measured the properties of these wavelength shifters. The particular mixtures were chosen because there is a substantial overlap between the emission spectrum of Coumarin and the absorption spectrum of DCM. The continuous wave and time-resolved fluorescence spectra have been studied as a function of component concentration to optimize the decay times, emission peaks and quantum yields. The mean decay times of these mixtures are in the range of 2.5--4.5 ns. The mean decay time increases with an increase in Coumarin concentration at a fixed DCM concentration or with a decrease in DCM concentration at a fixed Coumarin concentration. This indicates that the energy transfer is radiative at lower relative DCM concentrations and becomes non-radiative at higher DCM concentrations

  17. Meat mixture detection in Iberian pork sausages.

    Science.gov (United States)

    Ortiz-Somovilla, V; España-España, F; De Pedro-Sanz, E J; Gaitán-Jurado, A J

    2005-11-01

    Five homogenized meat mixture treatments of Iberian (I) and/or Standard (S) pork were set up. Each treatment was analyzed by NIRS as a fresh product (N=75) and as dry-cured sausage (N=75). Spectra acquisition was carried out using DA 7000 equipment (Perten Instruments), obtaining a total of 750 spectra. Several absorption peaks and bands were selected as the most representative for homogenized dry-cured and fresh sausages. Discriminant analysis and mixture prediction equations were carried out based on the spectral data gathered. The best results using discriminant models were for fresh products, with 98.3% (calibration) and 60% (validation) correct classification. For dry-cured sausages 91.7% (calibration) and 80% (validation) of the samples were correctly classified. Models developed using mixture prediction equations showed SECV=4.7, r(2)=0.98 (calibration) and 73.3% of validation set were correctly classified for the fresh product. These values for dry-cured sausages were SECV=5.9, r(2)=0.99 (calibration) and 93.3% correctly classified for validation.

  18. Catalytic Pyrolysis of Waste Plastic Mixture

    Science.gov (United States)

    Sembiring, Ferdianta; Wahyu Purnomo, Chandra; Purwono, Suryo

    2018-03-01

    Inorganic waste especially plastics still become a major problem in many places. Low biodegradability of this materials causes the effort in recycling become very difficult. Most of the municipal solid waste (MSW) recycling facilities in developing country only use composting method to recover the organic fraction of the waste, while the inorganic fraction is still untreated. By pyrolysis, plastic waste can be treated to produce liquid fuels, flammable gas and chars. Reduction in volume and utilization of the liquid and gas as fuel are the major benefits of the process. By heat integration actually this process can become a self-sufficient system in terms of energy demand. However, the drawback of this process is usually due to the diverse type of plastic in the MSW creating low grade of liquid fuel and harmful gases. In this study, the mixture of plastics i.e. polypropylene (PP) and polyethylene terephthalate (PET) is treated using pyrolysis with catalyst in several operating temperature. PET is problematic to be treated using pyrolysis due to wax-like byproduct in liquid which may cause pipe clogging. The catalyst is the mixture of natural zeolite and bentonite which is able to handle PP and PET mixture feed to produce high grade liquid fuels in terms of calorific value and other fuel properties.

  19. Structure of steam water mixture spray

    International Nuclear Information System (INIS)

    Mitsuhashi, Yuki; Mizutani, Hiroya; Sanada, Toshiyuki; Saito, Takayuki

    2008-01-01

    The flow structure of steam and water mixture spray is studied both numerically and experimentally. The velocity and pressure profiles of the single phase flow are calculated using numerical methods. Using calculated flow fields, the droplet behavior is predicted by the one-way interaction model. This numerical analysis clarifies that the droplets are still accelerated after they are sprayed from the nozzle. In the experiments, the spray of the mixture is observed by using ultra high-speed video camera, and the velocity field is measured by using PIV technique. Along with this PIV velocity field measurement, the velocities and diameters of droplets are measured by phase Doppler anemometry. Furthermore, mixing process of steam and water, and atomization process of liquid film are observed through the transparent nozzle. The high-speed photography observation reveals that the flow inside the nozzle forms the annular flow and the most of the liquid film is atomized at the nozzle outlet. Finally, the optimum method of processing mixture of steam and water is proposed. (author)

  20. Optimization of fruit punch using mixture design.

    Science.gov (United States)

    Kumar, S Bharath; Ravi, R; Saraswathi, G

    2010-01-01

    A highly acceptable dehydrated fruit punch was developed with selected fruits, namely lemon, orange, and mango, using a mixture design and optimization technique. The fruit juices were freeze dried, powdered, and used in the reconstitution studies. Fruit punches were prepared according to the experimental design combinations (total 10) based on a mixture design and then subjected to sensory evaluation for acceptability. Response surfaces of sensory attributes were also generated as a function of fruit juices. Analysis of data revealed that the fruit punch prepared using 66% of mango, 33% of orange, and 1% of lemon had highly desirable sensory scores for color (6.00), body (5.92), sweetness (5.68), and pleasantness (5.94). The aroma pattern of individual as well as combinations of fruit juices were also analyzed by electronic nose. The electronic nose could discriminate the aroma patterns of individual as well as fruit juice combinations by mixture design. The results provide information on the sensory quality of best fruit punch formulations liked by the consumer panel based on lemon, orange, and mango.

  1. Statistical experimental design for saltstone mixtures

    International Nuclear Information System (INIS)

    Harris, S.P.; Postles, R.L.

    1992-01-01

    The authors used a mixture experimental design for determining a window of operability for a process at the U.S. Department of Energy, Savannah River Site, Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. Cesium-137 will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach-rate properties of the supernate grout formed from various mixes of solidified coefficients for NO 3 and chromium were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag, and fly ash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used. The regression procedure (PROC REG) in SAS was used to produce analysis of variance (ANOVA) statistics. In addition, detailed model diagnostics are readily available for identifying suspicious observations. For convenience, trillinear contour (TLC) plots, a standard graphics tool for examining mixture response surfaces, of the fitted model were produced using ECHIP

  2. Tandem mass spectrometry: analysis of complex mixtures

    International Nuclear Information System (INIS)

    Singleton, K.E.

    1985-01-01

    Applications of tandem mass spectrometry (MS/MS) for the analysis of complex mixtures results in increased specificity and selectivity by using a variety of reagent gases in both negative and positive ion modes. Natural isotopic abundance ratios were examined in both simple and complex mixtures using parent, daughter and neutral loss scans. MS/MS was also used to discover new compounds. Daughter scans were used to identify seven new alkaloids in a cactus species. Three of these alkaloids were novel compounds, and included the first simple, fully aromatic isoquinoline alkaloids reported in Cactaceae. MS/MS was used to characterize the chemical reaction products of coal in studies designed to probe its macromolecular structure. Negative ion chemical ionization was utilized to study reaction products resulting from the oxidation of coal. Possible structural units in the precursor coal were predicted based on the reaction products identified, aliphatic and aromatic acids and their anhydrides. The MS/MS method was also used to characterize reaction products resulting from coal liquefaction and/or extraction. These studies illustrate the types of problems for which MS/MS is useful. Emphasis has been placed on characterization of complex mixtures by selecting experimental parameters which enhance the information obtained. The value of using MS/MS in conjunction with other analytical techniques as well as the chemical pretreatment is demonstrated

  3. The development of a very high stability electrostatic generator (1962); Etude et realisation d'un generateur electrostatique a tres haute stabilite (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Jonckheere, R E.L. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1962-07-01

    This thesis deals with the study of an electrostatic high voltage generator having a voltage stability of the order of 10{sup -6} per minute. This equipment should be very useful in electron microscopy. The electrostatic generator is studied as a control system element: transfer function, parasitic signals and noise are determined and a mathematical model is proposed. A theoretical study of the open loop transfer function, stability, transient response, voltage stabilization of five different control systems shows which one should be able to fulfill the requirements There follows a detailed study of drift, a description of the actual system and performance data. (author) [French] Cette etude concerne un generateur electrostatique capable de fournir une tres haute tension continue dont la stabilite relative est de l'ordre de 10{sup -6} pendant une minute. Une telle performance rend cet appareillage tres utile en microscopie electronique. La generatrice electrostatique est etudiee en tant qu'element d'un systeme asservi: on determine successivement la fonction de transfert, les perturbations, le bruit de fond et le modele mathematique. L'etude de cinq differents circuits de regulation en ce qui concerne leur fonction de transfert, stabilite, reponse en regime transitoire, attenuation des perturbations, permettra de choisir le systeme qui semble le mieux repondre aux exigences. Viennent ensuite une etude detaillee de la derive, la description de la realisation pratique et les resultats de mesure. (auteur)

  4. A study of the aptitude of soils under natural conditions to retain radiostrontium; Etude de la vocation des sols en place a la retention du radiostrontium

    Energy Technology Data Exchange (ETDEWEB)

    Bovard, P; Grauby, A [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Independently of the theoretical study of the propagation of radioactivity in the soil as a result of submersions or of radioactive rain, the authors have studied directly and practically how this radioactivity can vary in the actual soil. To this end a simple, rapid method has been perfected; it makes it possible to maintain for each soil sample the natural parameters (structure, humidity, etc.) without introducing boundary effects. In the laboratory, after charging the soil samples, part of the study of the propagation of radioactivity is done by autoradiography; finally, as a practical application, the study of an atomic site illustrates the methods described. (author) [French] Independamment de l'etude theorique de la propagation de la radioactivite dans le sol a la suite de submersions ou de pluies radioactives, les auteurs ont etudie directement et pratiquement comment pourrait evoluer cette radioactivite dans les sols en place. Pour cela, une methode simple et rapide a ete mise au point; elle permet de conserver pour chaque echantillon de sol, les parametres naturels (structure, humidite, etc...), sans introduire d'effets de paroi. En laboratoire, apres mise en charge des massifs preleves, une partie de l'etude de la propagation des radioelements est realisee par autoradiographie; enfin, une application pratique, l'etude d'un site atomique, illustre l'expose. (auteur)

  5. A study of the aptitude of soils under natural conditions to retain radiostrontium; Etude de la vocation des sols en place a la retention du radiostrontium

    Energy Technology Data Exchange (ETDEWEB)

    Bovard, P.; Grauby, A. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    Independently of the theoretical study of the propagation of radioactivity in the soil as a result of submersions or of radioactive rain, the authors have studied directly and practically how this radioactivity can vary in the actual soil. To this end a simple, rapid method has been perfected; it makes it possible to maintain for each soil sample the natural parameters (structure, humidity, etc.) without introducing boundary effects. In the laboratory, after charging the soil samples, part of the study of the propagation of radioactivity is done by autoradiography; finally, as a practical application, the study of an atomic site illustrates the methods described. (author) [French] Independamment de l'etude theorique de la propagation de la radioactivite dans le sol a la suite de submersions ou de pluies radioactives, les auteurs ont etudie directement et pratiquement comment pourrait evoluer cette radioactivite dans les sols en place. Pour cela, une methode simple et rapide a ete mise au point; elle permet de conserver pour chaque echantillon de sol, les parametres naturels (structure, humidite, etc...), sans introduire d'effets de paroi. En laboratoire, apres mise en charge des massifs preleves, une partie de l'etude de la propagation des radioelements est realisee par autoradiographie; enfin, une application pratique, l'etude d'un site atomique, illustre l'expose. (auteur)

  6. Contribution to the study of the stability of water-cooled reactors; Contribution a l'etude de la stabilite des reacteurs refroidis par de l'eau

    Energy Technology Data Exchange (ETDEWEB)

    Coudert, C [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires

    1969-06-01

    This work is devoted to the study of the stability of reactors cooled by water subjected only to natural convection. It is made up of two parts, a theoretical study and experimental work, each of these parts being devoted to a consideration of linear and non-linear conditions: - calculation of the transfer function of the reactor using neutronic and hydrodynamic linear equations with the determination of the instability threshold; - demonstration of the existence of the limiting oscillation cycle in the case of a linear feedback using MALKIN'S method; - measurement and interpretation of the reactor's transfer functions and of the hydrodynamic transfer functions; and - analysis of the noise due to boiling. (author) [French] Dans ce travail on etudie la stabilite des piles refroidies par de l'eau circulant en convection naturelle. Cette etude se divise en deux parties: un travail theorique et un travail experimental, chacune de ces parties comportant une etude lineaire et une etude non-lineaire: - calcul de la fonction de transfert du reacteur a partir des equations lineaires de la neutronique et de l'hydrodynamique avec determination du seuil d'instabilite; - demonstration de l'existence du cycle limite des oscillations dans le cas d'une retroaction lineaire en utilisant la methode de MALKIN; - mesure et interpretation de la fonction de transfert du reacteur et des fonctions de transfert hydrodynamiques; et - analyse du bruit d'ebullition. (auteur)

  7. The development of a very high stability electrostatic generator (1962); Etude et realisation d'un generateur electrostatique a tres haute stabilite (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Jonckheere, R.E.L. [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1962-07-01

    This thesis deals with the study of an electrostatic high voltage generator having a voltage stability of the order of 10{sup -6} per minute. This equipment should be very useful in electron microscopy. The electrostatic generator is studied as a control system element: transfer function, parasitic signals and noise are determined and a mathematical model is proposed. A theoretical study of the open loop transfer function, stability, transient response, voltage stabilization of five different control systems shows which one should be able to fulfill the requirements There follows a detailed study of drift, a description of the actual system and performance data. (author) [French] Cette etude concerne un generateur electrostatique capable de fournir une tres haute tension continue dont la stabilite relative est de l'ordre de 10{sup -6} pendant une minute. Une telle performance rend cet appareillage tres utile en microscopie electronique. La generatrice electrostatique est etudiee en tant qu'element d'un systeme asservi: on determine successivement la fonction de transfert, les perturbations, le bruit de fond et le modele mathematique. L'etude de cinq differents circuits de regulation en ce qui concerne leur fonction de transfert, stabilite, reponse en regime transitoire, attenuation des perturbations, permettra de choisir le systeme qui semble le mieux repondre aux exigences. Viennent ensuite une etude detaillee de la derive, la description de la realisation pratique et les resultats de mesure. (auteur)

  8. Study of electron groupings in the Saclay linear accelerator; Etude du groupement des electrons dans l'accelerateur lineaire de Saclay

    Energy Technology Data Exchange (ETDEWEB)

    Bergere, R; Veyssiere, A; Beil, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1965-07-01

    The classical theory of the linear accelerator buncher does not fit the experimental measurements of the shape of the bunch of electrons performed at Saclay by the method of the energy spectrum. If the spurious effect of the mode converter at the input of the linac is taken into account the theory can fit the experimental results and also explain the variations of the phase of the bunch on the accelerating sine wave. (authors) [French] Une etude classique du groupeur en tete de l'Accelerateur Lineaire de Saclav conduit a des resultats incompatibles avec les resultats experimentaux obtenus sur le groupement des electrons par l'etude du spectre des frequences rayonnees par le faisceau d'electrons ou par l'etude des spectres en energie. Par contre si l'effet parasite du convertisseur de mode a l'entree de l'accelerateur est pris en consideration les resultats theoriques coincident bien avec les resultats experimentaux et permettent en outre d'expliquer les variations du calage en phase des paquets elementaires d'electrons. (auteurs)

  9. Manufacturing cycle for pure neon-helium mixture production

    International Nuclear Information System (INIS)

    Batrakov, B.P.; Kravchenko, V.A.

    1980-01-01

    The manufacturing cycle for pure neon-helium mixture production with JA-300 nitrogen air distributing device has been developed. Gas mixture containing 2-3% of neon-helium mixture (the rest is mainly nitrogen 96-97%) is selected out of the cover of the JA-300 column condensator and enters the deflegmator under the 2.3-2.5 atm. pressure. The diflegmator presents a heat exchange apparatus in which at 78 K liquid nitrogen the condensation of nitrogen from the mixture of gases entering from the JA-300 column takes place. The enriched gas mixture containing 65-70% of neon-helium mixture and 30-35% of nitrogen goes out from the deflegmator. This enriched neon-helium mixture enters the gasgoeder for impure (65-70%) neon-helium mixture. Full cleaning of-neon helium mixture of nitrogen is performed by means of an adsorber. As adsorbent an activated coal has been used. Adsorption occurs at the 78 K temperature of liquid nitrogen and pressure P=0.1 atm. As activated coal cooled down to nitrogen temperature adsorbs nitrogen better than neon and helium, the nitrogen from the mixture is completely adsorbed. Pure neon-helium mixture from the adsorber comes into a separate gasgolder. In one campaign the cycle allows obtaining 2 m 3 of the mixture. The mixture contains 0.14% of nitrogen, 0.01% of oxygen and 0.06% of hydrogen

  10. Study of thermocouples for control of high temperatures; Etude de thermocouples pour le reperage des hautes temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Villamayor, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Faculte des Sciences de l' Universite de Lyon - 69 (France)

    1967-07-01

    Previous works have shown that the tungsten-rhenium alloys thermocouples were a good instrument for control of high temperatures. From its, the author has studied the W/W 26 per cent and W 5 per cent Re/W 26 per cent Re french manufactured thermocouples and intended for control of temperatures in nuclear reactors until 2300 deg. C. In 'out-pile' study he determines the general characteristics of these thermocouples: average calibration curves, thermal shocks influence, response times, and alloys allowing the cold source compensation. The evolution of these thermocouples under thermal neutron flux has been determined by 'in-pile' study. The observations have led the author to propose a new type of thermocouples settled of molybdenum-columbium alloys. (author) [French] Des travaux anterieurs ont montre que les thermocouples des alliages tungstene-rhenium etaient susceptibles de reperer avec precision des hautes temperatures. A partir de la, l'auteur a etudie las thermocouples W/W 26 pour cent Re et W 5 pour cent Re/W 26 pour cent Re de fabrication francaise et destines au controle des temperatures dans les reacteurs nucleaires, jusqu'a 2300 deg. C Dans l'etude 'hors-pile' il a determine les caracteristiques generales de ces thermocouples: courbes d'etalonnage moyen, influence des chocs thermiques, temps de reponse, et alliages assurant la compensation de soudure froide. L'etude 'en-pile' a permis de rendre compte de l'evolution de ces thermocouples sous flux neutroniques. Les phenomenes observes ont conduit l'auteur a proposer un nouveau type de thermocouples constitues d'alliages molybdene-niobium. (auteur)

  11. Study of radio-active ions in the atmosphere; Etude des ions radioactifs de l'atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Renoux, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1965-01-01

    A comparative study is made of active, deposits of radon and thoron in suspension in the atmosphere by means of {alpha} radiation counting, using ZELENY tubes, scattering equipment, filter papers or membranes. It has been possible to show the existence of small and large ions which are negative and positive, as well as of neutral radio-active nuclei; their properties are studied. A theoretical interpretation of the results is presented. The average content of radon (using the Ra A concentration) and of Th B in the air has been determined. The radioactive equilibrium between radon and its daughter products in atmospheric air are examined. The techniques developed for active radon and thoron deposits are applied to the study of artificial radio-activity, the analyses being carried out by means of {gamma} spectrometry. (author) [French] On effectue une etude comparative entre les depots actifs du radon et du thoron en suspension dont l'atmosphere a l'aide de comptages de rayonnement {alpha}, en utilisant des tubes de ZELENY, une batterie de diffusion, des papiers filtres ou des membranes. On met ainsi en evidence la presence de petits et gros ions negatifs et positifs, ainsi que celle de noyaux neutres radioactifs, et on etudie leurs proprietes. Une Interpretation theorique des resultats obtenus est developpee. On determine la teneur moyenne de l'air en radon (a partir de la concentration en Ra A) et en Th B. L'equilibre radioactif entre le radon et ses descendants, dans l'air atmospherique, est examine. Les Techniques mises au point pour les depots actifs du radon et du thoron sont appliquees a l'etude de la radioactivite artificielle, les depouillements s'effectuant par spectrometrie {gamma}. (auteur)

  12. Theoretical study for a digital transfer function analyser; Etude theorique pour un transferometre digital

    Energy Technology Data Exchange (ETDEWEB)

    Freycenon, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    This study deals with the harmonic analysis of the instantaneous counting rate of a pulse train. This arises from using a fission chamber for reactivity to power transfer function measurements by oscillation methods in reactors. The systematical errors due to the sampling process are computed. The integration carried out when sampling the signal modifies the formulae of the Nyquist theorem on spectrum folding. The statistical errors due to the noise are analysed: it is shown that the bandwidth of the spectral window applied to the noise frequency spectrum is equal to the inverse of the time duration of the experiment. A dead time of 25 per cent of the sampling time does not increase appreciably the bandwidth. A new method is proposed afterwards yielding very approximate results of the Fourier analysis during the experiment. The systematical errors arising from the measuring process are determined, and it is shown that the bandwidth of the corresponding spectral window is still given by the inverse of the time duration of the experiment. (author) [French] Cette etude se rapporte a l'analyse harmonique de la valeur instantanee du taux de comptage d'une suite d'impulsions. On rencontre ce probleme dans l'utilisation de chambres a fission pour les mesures de fonction de transfert reactivite-puissance par la methode d'oscillation dans les piles. On calcule l'erreur systematique due au processus d'echantillonnage ou l'integration operee modifie les formules classiques de recouvrement du spectre. On analyse ensuite les erreurs statistiques dues au bruit de fond. On montre que la largeur de bande de la fenetre spectrale appliquee au spectre de puissance du bruit est donnee par l'inverse du temps de mesure. Un temps mort de 25 pour cent du temps de prelevement n'accroit pas sensiblement cette largeur de bande. On propose ensuite un procede simple qui permet d'obtenir, en cours d'experience, des resultats tres approches de l'analyse de Fourier. On determine les erreurs

  13. Study of the recrystallisation of irradiated uranium; Etude sur l'uranium irradie

    Energy Technology Data Exchange (ETDEWEB)

    Bloch, J; Mustelier, J P; Bussy, P; Blin, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1958-07-01

    1- Study of the recrystallisation of irradiated uranium. The recrystallisation of uranium irradiated to a burnup level of 220 MWj/t, at a temperature of the order of 350 deg. C, has been investigated. The observations were made chiefly by means of micrography an hardness measurements. If the irradiated metal is compared with a cold-drawn metal showing the same shearing of the twinned crystals, and therefore the same rate of plastic deformation, as the irradiated metal, it is noted that the restoring of the irradiated metal takes place at a considerably higher temperature than that of the cold-drawn metal. Pre-crystallisation is very much delayed. Only, a passage of the {alpha}-{beta} transformation point quickly wipes out irradiation effect. 2- Hardening of uranium by irradiation. Using hardness measurements we have studied more especially the effect of very weak irradiations on uranium (integrated flux < 10{sup 16} nvt). The hardness does not increase linearly with the flux, but a period of incubation is observed probably representing the time necessary for saturation of the dislocations. (author)Fren. [French] 1- Etude de la recristallisation de l'uranium irradie. On a etudie la recristallisation d'uranium irradie jusqu'a un taux de combustion de 220 MWj/t a une temperature de l'ordre de 350 deg. C. Les observations ont ete faites principalement a l'aide de la micrographie et de la durete. Si l'on compare le metal irradie avec un metal ecroui presentant le meme cisaillement des macles, donc le meme taux de deformation plastique que le metal irradie, on constate que la restauration du metal irradie se fait a une temperature notablement superieure a celle du metal ecroui. La recristallisation est tres retardee. Seul, un passage du point de transformation {alpha}-{beta} efface rapidement l'effet de l'irradiation. 2- Durcissement de l'uranium par irradiation. Nous avons, a l'aide de la durete, etudie plus particulierement l'effet de tres faibles irrtions sur l

  14. Complex mixtures, complex responses: Assessing pharmaceutical mixtures using field and laboratory approaches

    Science.gov (United States)

    Schoenfuss, Heiko L.; Furlong, Edward T.; Phillips, Patrick J.; Scott, Tia-Marie; Kolpin, Dana W.; Cetkovic-Cvrlje, Marina; Lesteberg, Kelsey E.; Rearick, Daniel C.

    2016-01-01

    Pharmaceuticals are present in low concentrations (pharmaceutical formulation facilities. Using existing concentration data, the authors assessed pharmaceuticals in laboratory exposures of fathead minnows (Pimephales promelas) and added environmental complexity through effluent exposures. In the laboratory, larval and mature minnows were exposed to a simple opioid mixture (hydrocodone, methadone, and oxycodone), an opioid agonist (tramadol), a muscle relaxant (methocarbamol), a simple antidepressant mixture (fluoxetine, paroxetine, venlafaxine), a sleep aid (temazepam), or a complex mixture of all compounds. Larval minnow response to effluent exposure was not consistent. The 2010 exposures resulted in shorter exposed minnow larvae, whereas the larvae exposed in 2012 exhibited altered escape behavior. Mature minnows exhibited altered hepatosomatic indices, with the strongest effects in females and in mixture exposures. In addition, laboratory-exposed, mature male minnows exposed to all pharmaceuticals (except the selective serotonin reuptake inhibitor mixture) defended nest sites less rigorously than fish in the control group. Tramadol or antidepressant mixture exposure resulted in increased splenic T lymphocytes. Only male minnows exposed to whole effluent responded with increased plasma vitellogenin concentrations. Female minnows exposed to pharmaceuticals (except the opioid mixture) had larger livers, likely as a compensatory result of greater prominence of vacuoles in liver hepatocytes. The observed alteration of apical endpoints central to sustaining fish populations confirms that effluents containing waste streams from pharmaceutical formulation facilities can adversely impact fish populations but that the effects may not be temporally consistent. The present study highlights the importance of including diverse biological endpoints spanning levels of biological organization and life stages when assessing contaminant interactions.

  15. Mixture Density Mercer Kernels: A Method to Learn Kernels

    Data.gov (United States)

    National Aeronautics and Space Administration — This paper presents a method of generating Mercer Kernels from an ensemble of probabilistic mixture models, where each mixture model is generated from a Bayesian...

  16. Performance evaluation of Louisiana superpave mixtures : tech summary.

    Science.gov (United States)

    2008-12-01

    The primary objective of this research was to evaluate the fundamental engineering : properties and mixture performance of Superpave hot mix asphalt (HMA) mixtures : in Louisiana through laboratory mechanistic tests, aggregate gradation analysis, and...

  17. Determinant of flexible Parametric Estimation of Mixture Cure ...

    African Journals Online (AJOL)

    PROF. OLIVER OSUAGWA

    2015-12-01

    Dec 1, 2015 ... Suitability of four parametric mixture cure models were considered namely; Log .... regression analysis which relies on the ... The parameter of mixture cure fraction model was ..... Stochastic Models of Tumor Latency and Their.

  18. Implementation of warm-mix asphalt mixtures in Nebraska pavements.

    Science.gov (United States)

    2012-07-01

    The primary objective of this research is to evaluate the feasibility of several WMA mixtures as potential asphalt paving : mixtures for Nebraska pavements. To that end, three well-known WMA additives (i.e., Sasobit, Evotherm, and Advera : synthetic ...

  19. Kinetic study of the reaction of uranium with various carbon-containing gases; Etude cinetique de la reaction sur l'uranium de differents gaz carbones

    Energy Technology Data Exchange (ETDEWEB)

    Feron, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1963-09-15

    The kinetic study of the reaction U + CO{sub 2} and U + CO has been performed by a thermogravimetric method on a spherical uranium powder, in temperature ranges respectively from 460 to 690 deg. C and from 570 to 850 deg. C. The reaction with carbon dioxide leads to uranium dioxide. A carbon deposition takes place at the same time. The global reactions is the result of two reactions: U + 2 CO{sub 2} {yields} UO{sub 2} + 2 CO U + CO{sub 2} {yields} UO{sub 2} + C The reaction with carbon monoxide leads to a mixture of dioxide UO{sub 2}, dicarbide UC{sub 2} and free carbon. The main reaction can be written. U + CO {yields} 1/2 UO{sub 2} + 1/2 UC{sub 2} The free carbon results of the disproportionation of the carbon monoxide. A remarkable separation of the two phases UO{sub 2} and UC{sub 2} can be observed. A mechanism accounting for the phenomenon has been proposed. The two reactions U + CO{sub 2} and U + CO begin with a long germination period, after which, the reaction velocity seems to be limited in both cases by the ionic diffusion of oxygen through the uranium dioxide. (author) [French] L'etude cinetique des reactions U sol + CO{sub 2} gaz et U sol + CO gaz a ete effectuee par thermogravirnetrie sur une poudre d'uranium a grains spheriques, les domaines de temperature etudies s'etendant respectivement de 460 a 690 deg. C et de 570 a 850 deg. C. L'action du dioxyde de carbone conduit au dioxyde d'uranium UO{sub 2}; il se produit en meme temps un depot de carbone. La reaction globale resulte des deux reactions: U + 2 CO{sub 2} {yields} UO{sub 2} + 2 CO U + CO{sub 2} {yields} UO{sub 2} + C Le mono-oxyde de carbone conduit a un melange de dioxyde UO{sub 2}, de dicarbure UC{sub 2} et de carbone libre. La reaction principale s'ecrit: U + CO {yields} 1/2 UO{sub 2} + 1/2 UC{sub 2} Le carbone libre provient de la dismutation du mono-oxyde de carbone. On observe une separation remarquable des deux phases UO{sub 2} et UC{sub 2}; un mecanisme rendant compte de ce phenomene a

  20. A Statistical Approach to Optimizing Concrete Mixture Design

    OpenAIRE

    Ahmad, Shamsad; Alghamdi, Saeid A.

    2014-01-01

    A step-by-step statistical approach is proposed to obtain optimum proportioning of concrete mixtures using the data obtained through a statistically planned experimental program. The utility of the proposed approach for optimizing the design of concrete mixture is illustrated considering a typical case in which trial mixtures were considered according to a full factorial experiment design involving three factors and their three levels (33). A total of 27 concrete mixtures with three replicate...

  1. Nanoporous polymer--clay hybrid membranes for gas separation.

    Science.gov (United States)

    Defontaine, Guillaume; Barichard, Anne; Letaief, Sadok; Feng, Chaoyang; Matsuura, Takeshi; Detellier, Christian

    2010-03-15

    Nanohybrid organo-inorgano clay mineral-polydimethylsiloxane (PDMS) membranes were prepared by the reaction of pure and/or modified natural clay minerals (Sepiolite and montmorillonite) with PDMS in hexane, followed by evaporation of the solvent at 70 degrees C. The membranes were characterized by means of XRD, SEM, ATD-TG and solid state (29)Si magic angle spinning (MAS) and cross-polarization (CP) CP/MAS NMR. The morphology of the membranes depends on the content loading of clay mineral. For low content, the membrane composition is homogeneous, with well dispersed nanoparticles of clay into the polymer matrix, whereas for higher clay content, the membranes are constituted also of a mixture of well dispersed nanoparticles into the polymer, but in the presence of agglomerations of small clay particles. Quantitative (29)Si MAS NMR demonstrated a strong correlation between the clay content of the membrane and the average length of the PDMS chain, indicating that the nanohybrid material is made of clay particles covalently linked to the PDMS structure. This is particularly the case for Sepiolite with has a high density of Q(2) silanol sites. The separation performances of the prepared membranes were tested for CO(2)/CH(4) and O(2)/N(2) mixtures. The observed separation factors showed an increase of the selectivity in the case of CO(2)/CH(4) in comparison with membranes made from PDMS alone under the same conditions. 2009 Elsevier Inc. All rights reserved.

  2. Production of heavy water in France; Etude sur la production d'eau lourde en France

    Energy Technology Data Exchange (ETDEWEB)

    Lerat, J M; Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Lefrancois, B [Houllere du Bassin du Nord et du Pas de Calais (France)

    1964-07-01

    Since 1958, studies relating to heavy water production have covered several processes. Each one has been examined to a greater or lesser degree and attention has finally been concentrated on the isotopic exchanges between hydrogen sulphide and water and between ammonia and synthesis gas, the pilot experiment having shown that hydrogen distillation, although technologically satisfactory, was not competitive. NH{sub 3} synthesis gas exchange process; 1) Research was continued and led to the decision to build a production unit, devoted also to the synthesis of ammonia. The process essentially depends on the source of the synthesis gas; the use of a H{sub 2}O/H{sub 2} exchange, which could make it independent, has in fact been rejected for economic reasons. Amongst the various possible designs for the process, the one temperature system was chosen, in spite of certain technological problems, because of it provides: a high enrichment with a reduced number of contact devices. These have now been perfected after large-scale pilot tests. The original industrial experiment to be set in operation will supply useful information for second generation plants, whether they use the one temperature lay out again or whether they adopt the two temperature system. H{sub 2}S-H{sub 2}O exchange process. The pilot plant, described in 1958, has been used for a systematic study of corrosion. It was possible to proceed to preliminary specifications of plants, with 2 or 3 H{sub 2}S - H{sub 2}O stages exchange for primary enrichment. They final stage beyond a 10 to 20 p.100 D{sub 2}O concentration being carried out by the distillation of water. Various heat exchange systems have been studied in detail and it was concluded that choices, as for instance the one of optimum division of the cascade, were eventually to be made according to the particular economic conditions of creation at the chosen location of the plant. (author) [French] Depuis 1958 les etudes concernant la production d

  3. TEMPERATURE INFLUENCE ON PHASE STABILITY OF ETHANOL-GASOLINE MIXTURES

    Directory of Open Access Journals (Sweden)

    Valerian Cerempei

    2011-06-01

    Full Text Available The article investigates phase stability of ethanol-gasoline mixtures depending on their composition, water concentration in ethanol and ethanol-gasoline mixture and temperature. There have been determined the perfect functioning conditions of spark ignition engines fueled with ethanol-gasoline mixtures.

  4. Optimal (Solvent) Mixture Design through a Decomposition Based CAMD methodology

    DEFF Research Database (Denmark)

    Achenie, L.; Karunanithi, Arunprakash T.; Gani, Rafiqul

    2004-01-01

    Computer Aided Molecular/Mixture design (CAMD) is one of the most promising techniques for solvent design and selection. A decomposition based CAMD methodology has been formulated where the mixture design problem is solved as a series of molecular and mixture design sub-problems. This approach is...

  5. Low temperature irradiation of vitrifiable mixtures of unsaturated monomers

    International Nuclear Information System (INIS)

    Kaetsu, I.; Ito, A.; Hayashi, K.

    1975-01-01

    A specific mixture containing at least one polymerizable unsaturated monomer which is not vitrifiable by itself can advantageously be polymerized by irradiating the mixture at a temperature not higher than 100 0 C above glass transition temperature of the mixture with an ionizing radiation and/or a light. 12 claims, 6 drawings, figures

  6. Lessons learned in managing alfalfa-grass mixtures

    Science.gov (United States)

    Grass-alfalfa mixtures have a number of benefits that make them attractive to producers. However, they can be problematic to establish and maintain. Research programs have made progress in understanding the benefits and challenges of alfalfa-grass mixtures. Mixtures may have greater winter survival ...

  7. Toward the Rational Use of Exposure Information in Mixtures Toxicology

    Science.gov (United States)

    Of all the disciplines of toxicology, perhaps none is as dependent on exposure information as Mixtures Toxicology. Identifying real world mixtures and replicating them in the laboratory (or in silico) is critical to understanding their risks. Complex mixtures such as cigarett...

  8. Bayesian D-Optimal Choice Designs for Mixtures

    NARCIS (Netherlands)

    A. Ruseckaite (Aiste); P.P. Goos (Peter); D. Fok (Dennis)

    2014-01-01

    markdownabstract__Abstract__ Consumer products and services can often be described as mixtures of ingredients. Examples are the mixture of ingredients in a cocktail and the mixture of different components of waiting time (e.g., in-vehicle and out-of-vehicle travel time) in a transportation

  9. Combustion of powdery tungsten in pyrotechnic mixtures

    International Nuclear Information System (INIS)

    Ivanov, G.V.; Reshetov, A.A.; Viktorenko, A.M.; Surkov, V.G.; Karmadonov, L.N.

    1982-01-01

    The basic regularities of tungsten burning (powder 2-5 μm) with oxidizers most typical for pyrotechnics: nitrates, lead and barium peroxides (powder, 2-8 μm) and potassium perchlorate (powder, 2-8 μm) are studied. Dependences of burning rate as a function of pressure and ratio of components are established. It is supposed that tungsten burning in mixtures with the mentioned nitrates is a complex and multistage process the rate of which is determined by tungsten dissolution in nitrate melts. Analysis of burning products using available methods is complex

  10. Diffusive flux of energy in binary mixtures

    International Nuclear Information System (INIS)

    Sampaio, R.S.

    1976-04-01

    The diffusive flux of energy j tilde is studied through the reduced diffusive flux of energy K tilde, which obeys equations of the form: sim(delta K tilde/delta grad rho sub(α))= sim(delta K tilde/delta grad theta)=0. By a representation theorem, herein proved, is obtained a general representation for K tilde which is simplified, for the case of binary mixtures, using the principle of objectivity. Some consequences of this representation are discussed such as the symmetry of the partial stresses T 1 tilde and T 2 tilde and the difference between the normal stresses [pt

  11. Challenge of coal-liquid mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Peirce, T

    1985-09-01

    The near-term prospect for coal-water (CWMs) mixtures as a convenient replacement fuel for UK oil-fired plant is discussed. Specific use of CWMs in industrial water-tube boilers is presented. The article shows how such developments complement the introduction of new, modern coal-designed industrial combustion equipment in the form of fully automatic stokers and fluidized bed combustion systems. Topics presented include properties and preparation of CWM, combustion characteristics of CWM, and boiler conversion. 9 references, 4 figures.

  12. Conditional Density Approximations with Mixtures of Polynomials

    DEFF Research Database (Denmark)

    Varando, Gherardo; López-Cruz, Pedro L.; Nielsen, Thomas Dyhre

    2015-01-01

    Mixtures of polynomials (MoPs) are a non-parametric density estimation technique especially designed for hybrid Bayesian networks with continuous and discrete variables. Algorithms to learn one- and multi-dimensional (marginal) MoPs from data have recently been proposed. In this paper we introduce...... two methods for learning MoP approximations of conditional densities from data. Both approaches are based on learning MoP approximations of the joint density and the marginal density of the conditioning variables, but they differ as to how the MoP approximation of the quotient of the two densities...

  13. Thermodynamic properties of mixtures of liquids

    International Nuclear Information System (INIS)

    Benedetti, A.V.; Cilense, M.; Vollet, D.

    1982-01-01

    The molar excess enthalpy (H sup(-E)) of water-ethanol has been measured at 298.15, 306.85, 313.95 and 319.75 K. The mixtures are exothermics at studied temperatures with minimum values of -785, -655, -555 and -490 J. mol -1 respectively, at value of X 2 about 0.16. The other thermodynamics properties have been obtained from experimental data and data from literature. The results are interpreted qualitatively by considering molecular interactions in solution. (Author) [pt

  14. Pycnonuclear reaction rates for binary ionic mixtures

    Science.gov (United States)

    Ichimaru, S.; Ogata, S.; Van Horn, H. M.

    1992-01-01

    Through a combination of compositional scaling arguments and examinations of Monte Carlo simulation results for the interparticle separations in binary-ionic mixture (BIM) solids, we have derived parameterized expressions for the BIM pycnonuclear rates as generalizations of those in one-component solids obtained previously by Salpeter and Van Horn and by Ogata et al. We have thereby discovered a catalyzing effect of the heavier elements, which enhances the rates of reactions among the lighter elements when the charge ratio exceeds a critical value of approximately 2.3.

  15. Distinguishing computable mixtures of quantum states

    Science.gov (United States)

    Grande, Ignacio H. López; Senno, Gabriel; de la Torre, Gonzalo; Larotonda, Miguel A.; Bendersky, Ariel; Figueira, Santiago; Acín, Antonio

    2018-05-01

    In this article we extend results from our previous work [Bendersky et al., Phys. Rev. Lett. 116, 230402 (2016), 10.1103/PhysRevLett.116.230402] by providing a protocol to distinguish in finite time and with arbitrarily high success probability any algorithmic mixture of pure states from the maximally mixed state. Moreover, we include an experimental realization, using a modified quantum key distribution setup, where two different random sequences of pure states are prepared; these sequences are indistinguishable according to quantum mechanics, but they become distinguishable when randomness is replaced with pseudorandomness within the experimental preparation process.

  16. Process for purification of gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Vasiliev, S Z; Letitschevskij, V I; Maergojz, I I; Michailov, L A; Puschkarev, L I

    1977-06-23

    The process relates to the purification of gas mixtures of N, H, and Ar, or N and H, or N and O which contain CO, CO/sub 2/ and water vapour. Single-stage adsorption occurs under standard pressure at temperatures from -40 to +4/sup 0/C up to the point of CO penetration through the zeolite layer. Zeolite is of type A or X combined with Ca, Na, Ag, Cd, Co, Ni, Mn or a natural zeolite of the type klinoptilolite. Regeneration is achieved at constant temperature and pressure of 1-5x10/sup -1/ Torr or by heating to 120-600/sup 0/C.

  17. Flows and chemical reactions in heterogeneous mixtures

    CERN Document Server

    Prud'homme, Roger

    2014-01-01

    This book - a sequel of previous publications 'Flows and Chemical Reactions' and 'Chemical Reactions in Flows and Homogeneous Mixtures' - is devoted to flows with chemical reactions in heterogeneous environments.  Heterogeneous media in this volume include interfaces and lines. They may be the site of radiation. Each type of flow is the subject of a chapter in this volume. We consider first, in Chapter 1, the question of the generation of environments biphasic individuals: dusty gas, mist, bubble flow.  Chapter 2 is devoted to the study at the mesoscopic scale: particle-fluid exchange of mom

  18. Gaussian Mixture Model of Heart Rate Variability

    Science.gov (United States)

    Costa, Tommaso; Boccignone, Giuseppe; Ferraro, Mario

    2012-01-01

    Heart rate variability (HRV) is an important measure of sympathetic and parasympathetic functions of the autonomic nervous system and a key indicator of cardiovascular condition. This paper proposes a novel method to investigate HRV, namely by modelling it as a linear combination of Gaussians. Results show that three Gaussians are enough to describe the stationary statistics of heart variability and to provide a straightforward interpretation of the HRV power spectrum. Comparisons have been made also with synthetic data generated from different physiologically based models showing the plausibility of the Gaussian mixture parameters. PMID:22666386

  19. HDT mixtures treatment strategies by gas chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Laquerbe, C.; Contreras, S.; Demoment, J. [Commissariat a l' Energie Atomique - CEA/Valduc, F-21121 Is sur Tille (France)

    2008-07-15

    Gas phase chromatographic processes are of interest for the separation of hydrogen isotopes from an HDT mixture. For a certain quantity, they are very competitive and present several benefits. Nevertheless no active packing material allows to have simultaneously good enrichment performances for tritium production and high decontamination capabilities for HD gases. The influence of the packing material is first described in this article. Then two specific processes (TCAP and Reverse Chromatography), each well adapted to perform one target, are presented. Finally, the problematic to propose an optimized treatment scheme associating these two processes is formulated. (authors)

  20. HDT mixtures treatment strategies by gas chromatography

    International Nuclear Information System (INIS)

    Laquerbe, C.; Contreras, S.; Demoment, J.

    2008-01-01

    Gas phase chromatographic processes are of interest for the separation of hydrogen isotopes from an HDT mixture. For a certain quantity, they are very competitive and present several benefits. Nevertheless no active packing material allows to have simultaneously good enrichment performances for tritium production and high decontamination capabilities for HD gases. The influence of the packing material is first described in this article. Then two specific processes (TCAP and Reverse Chromatography), each well adapted to perform one target, are presented. Finally, the problematic to propose an optimized treatment scheme associating these two processes is formulated. (authors)

  1. Detonation of hydrogen-air mixtures

    International Nuclear Information System (INIS)

    Lee, J.H.S.; Knystautas, R.; Benedick, W.B.

    1983-01-01

    The detonation of a hydrogen-air cloud subsequent to an accidental release of hydrogen into ambient surroundings cannot be totally ruled out in view of the relative sensitivity of the hydrogen-air system. The present paper investigates the key parameters involved in hydrogen-air detonations and attempts to establish quantitative correlations between those that have important practical implications. Thus, for example, the characteristic length scale lambda describing the cellular structure of a detonation front is measured for a broad range of hydrogen-air mixtures and is quantitatively correlated with the key dynamic detonation properties such as detonability, transmission and initiation

  2. Computing Properties Of Chemical Mixtures At Equilibrium

    Science.gov (United States)

    Mcbride, B. J.; Gordon, S.

    1995-01-01

    Scientists and engineers need data on chemical equilibrium compositions to calculate theoretical thermodynamic properties of chemical systems. Information essential in design and analysis of such equipment as compressors, turbines, nozzles, engines, shock tubes, heat exchangers, and chemical-processing equipment. CET93 is general program that calculates chemical equilibrium compositions and properties of mixtures for any chemical system for which thermodynamic data are available. Includes thermodynamic data for more than 1,300 gaseous and condensed species and thermal-transport data for 151 gases. Written in FORTRAN 77.

  3. Modeling phase equilibria for acid gas mixtures using the CPA equation of state. Part II: Binary mixtures with CO2

    DEFF Research Database (Denmark)

    Tsivintzelis, Ioannis; Kontogeorgis, Georgios; Michelsen, Michael Locht

    2011-01-01

    In Part I of this series of articles, the study of H2S mixtures has been presented with CPA. In this study the phase behavior of CO2 containing mixtures is modeled. Binary mixtures with water, alcohols, glycols and hydrocarbons are investigated. Both phase equilibria (vapor–liquid and liquid–liqu...

  4. An equiratio mixture model for non-additive components : a case study for aspartame/acesulfame-K mixtures

    NARCIS (Netherlands)

    Schifferstein, H.N.J.

    1996-01-01

    The Equiratio Mixture Model predicts the psychophysical function for an equiratio mixture type on the basis of the psychophysical functions for the unmixed components. The model reliably estimates the sweetness of mixtures of sugars and sugar-alchohols, but is unable to predict intensity for

  5. Contribution to the micro-calorimetric study of the characteristics of radio-elements and to their qualitative and quantitative analysis; Contribution a l'etude microcalorimetrique des caracteristiques des radio-elements et a leurs analyses qualitative et quantitative

    Energy Technology Data Exchange (ETDEWEB)

    Ozias, Y [Centre de Production de Plutonium de Marcoule, 30 (France)

    1964-10-01

    The principle of this study consists in using the E. CALVET microcalorimeter for recording the energy flux emitted by radio-elements as a function of time, and in determining from this curve either their characteristics (half-life and radiation energy), or the composition of a mixture of radio-elements. In the first part the theoretical relationships describing radioactivity have been adapted to the microcalorimetric study. In the second part an experimental determination has been made using the E. CALVET microcalorimeter of the characteristics of various radio-elements, yttrium 90, phosphorus 32, sulphur 35, iodine 131, etc and of their mixtures. In particular a study has been made of the isotopic analysis of a {sup 239}Pu - {sup 240}Pu mixture, sometimes in the presence of {sup 241}Pu. The microcalorimetric method is not as sensitive as conventional counting methods, its limit appears to be at the present about 1 micro-watt for the apparatus used, it is however the most direct method in the case of emitters of weakly absorbed radiation ({alpha} and {beta}). For the {gamma} emitters only a part of the energy is absorbed by the walls of the container. The determination of their characteristics and of their masses in the mixtures depends neither on the shape, on the dilution or even less on the auto-absorption of the source. For high activity samples this auto-absorption is the cause of great difficulties in conventional methods which complicate the operations: divisions, dissolutions, dilutions, all of which are liable to introduce errors. The calorimetric method makes it possible to work on the untreated sample. All these measurements have been carried out using the conventional E CALVET calorimeter; to carry out an exact measurement of the energy due to {gamma} radiation, however, it is necessary to build special apparatus with a lead block the size of which is given by the author's calculations. The calorimetric method makes it possible to attain an accuracy

  6. Poisson Mixture Regression Models for Heart Disease Prediction.

    Science.gov (United States)

    Mufudza, Chipo; Erol, Hamza

    2016-01-01

    Early heart disease control can be achieved by high disease prediction and diagnosis efficiency. This paper focuses on the use of model based clustering techniques to predict and diagnose heart disease via Poisson mixture regression models. Analysis and application of Poisson mixture regression models is here addressed under two different classes: standard and concomitant variable mixture regression models. Results show that a two-component concomitant variable Poisson mixture regression model predicts heart disease better than both the standard Poisson mixture regression model and the ordinary general linear Poisson regression model due to its low Bayesian Information Criteria value. Furthermore, a Zero Inflated Poisson Mixture Regression model turned out to be the best model for heart prediction over all models as it both clusters individuals into high or low risk category and predicts rate to heart disease componentwise given clusters available. It is deduced that heart disease prediction can be effectively done by identifying the major risks componentwise using Poisson mixture regression model.

  7. Health and environmental effects of complex chemical mixtures: proceedings

    Energy Technology Data Exchange (ETDEWEB)

    1985-01-01

    The Office of Health and Environmental Research (OHER) of the Department of Energy supports a broad long-term research program on human health and environmental effects from potential exposure to energy-related complex chemical mixtures. The program seeks basic mechanistic data on the effects of complex mixtures at the cellular, molecular, and whole animal levels to aid in predicting human health effects and seeks ecological data on biological and physical transformations in the mixtures, concentrations of the mixtures in various compartments of the environment, and potential routes for human exposure to these mixtures (e.g., food chain). On June 17-18, 1985, OHER held its First Annual Technical Meeting on the Complex Chemical Mixtures Program in Chicago, IL. The primary purpose of the meeting was to enable principal investigators to report the research status and accomplishments of ongoing complex chemical mixture studies supported by OHER. To help focus future research directions round table discussions were conducted.

  8. mixtools: An R Package for Analyzing Mixture Models

    Directory of Open Access Journals (Sweden)

    Tatiana Benaglia

    2009-10-01

    Full Text Available The mixtools package for R provides a set of functions for analyzing a variety of finite mixture models. These functions include both traditional methods, such as EM algorithms for univariate and multivariate normal mixtures, and newer methods that reflect some recent research in finite mixture models. In the latter category, mixtools provides algorithms for estimating parameters in a wide range of different mixture-of-regression contexts, in multinomial mixtures such as those arising from discretizing continuous multivariate data, in nonparametric situations where the multivariate component densities are completely unspecified, and in semiparametric situations such as a univariate location mixture of symmetric but otherwise unspecified densities. Many of the algorithms of the mixtools package are EM algorithms or are based on EM-like ideas, so this article includes an overview of EM algorithms for finite mixture models.

  9. Contribution to a research on electron beam welding of metals; Contribution a l'etude de la soudure des metaux par faisceau d'electrons

    Energy Technology Data Exchange (ETDEWEB)

    Stohr, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-03-15

    under such conditions that the molten zone shows a small section, which is the main characteristic of this method. These tests have also established that the hollow cut by the electron beam, is free of molten metal, which allows a flow of electrons, whose penetration into the material is negligible. This way of looking has been confirmed by macro-graphies of mixtures, where very short welding points have been performed. These macro-graphies show the existence of a central hole. Tests made under dynamic operating confirm also the existence of a hole, when during the welding process, the electron beam pressure, the molten metal is pushed against the height, then existence of a hole, when during the welding process, the electron beam is suddenly cut off. Therefore, the welding process can be explained as follows: Through electron beam pressure, the molten metal is pushed against the height, then flows down, once the electron beam has moved away, and fills the previously made hole. The existence of a welding seam corroborates this point of view: autoradiographic of straight sections of parts containing radiotracers, show well the mixing due to metal flow. As a matter of fact, the filling of the hole is made by the molten metal coming as well from the higher part, as the lateral back part of the hole (on grounds of way of moving); The penetrating depth also depends on material's characteristics. Tests made with pieces of Cu, Fe, Al show that the penetrating depth is almost proportional to specific heat and in this particular case, one gets: h(Al) / C(Al) = h (Fe) / C (Fe) = h (Cu) / C (Cu) This proportionality comes to an end, welding alloys with one or several additional elements show a high vapour pressure at the melting pint. Tests made with Aluminium and an Al-Mg alloy show indeed a considerable increase of penetrating depth for the latter, in spite of the fact, that the specific heat is practically the same. This increase of penetrating depth can be explained by the

  10. Putting Priors in Mixture Density Mercer Kernels

    Science.gov (United States)

    Srivastava, Ashok N.; Schumann, Johann; Fischer, Bernd

    2004-01-01

    This paper presents a new methodology for automatic knowledge driven data mining based on the theory of Mercer Kernels, which are highly nonlinear symmetric positive definite mappings from the original image space to a very high, possibly infinite dimensional feature space. We describe a new method called Mixture Density Mercer Kernels to learn kernel function directly from data, rather than using predefined kernels. These data adaptive kernels can en- code prior knowledge in the kernel using a Bayesian formulation, thus allowing for physical information to be encoded in the model. We compare the results with existing algorithms on data from the Sloan Digital Sky Survey (SDSS). The code for these experiments has been generated with the AUTOBAYES tool, which automatically generates efficient and documented C/C++ code from abstract statistical model specifications. The core of the system is a schema library which contains template for learning and knowledge discovery algorithms like different versions of EM, or numeric optimization methods like conjugate gradient methods. The template instantiation is supported by symbolic- algebraic computations, which allows AUTOBAYES to find closed-form solutions and, where possible, to integrate them into the code. The results show that the Mixture Density Mercer-Kernel described here outperforms tree-based classification in distinguishing high-redshift galaxies from low- redshift galaxies by approximately 16% on test data, bagged trees by approximately 7%, and bagged trees built on a much larger sample of data by approximately 2%.

  11. A mixture approach to vagueness and ambiguity.

    Directory of Open Access Journals (Sweden)

    Steven Verheyen

    Full Text Available When asked to indicate which items from a set of candidates belong to a particular natural language category inter-individual differences occur: Individuals disagree which items should be considered category members. The premise of this paper is that these inter-individual differences in semantic categorization reflect both ambiguity and vagueness. Categorization differences are said to be due to ambiguity when individuals employ different criteria for categorization. For instance, individuals may disagree whether hiking or darts is the better example of sports because they emphasize respectively whether an activity is strenuous and whether rules apply. Categorization differences are said to be due to vagueness when individuals employ different cut-offs for separating members from non-members. For instance, the decision to include hiking in the sports category or not, may hinge on how strenuous different individuals require sports to be. This claim is supported by the application of a mixture model to categorization data for eight natural language categories. The mixture model can identify latent groups of categorizers who regard different items likely category members (i.e., ambiguity with categorizers within each of the groups differing in their propensity to provide membership responses (i.e., vagueness. The identified subgroups are shown to emphasize different sets of category attributes when making their categorization decisions.

  12. A simple mixture to enhance muscle transmittance

    Science.gov (United States)

    Oliveira, Luís; Lage, Armindo; Clemente, Manuel Pais; Tuchin, Valery V.

    2008-06-01

    Skeletal muscle is a fibrous tissue composed by muscle fibers and interstitial fluid. Due to this constitution, the muscle presents a non uniform refractive index profile that origins strong light scattering. One way to improve tissue transmittance is to reduce this refractive index mismatch by immersing the muscle in an optical clearing agent. As a consequence of such immersion tissue also suffers dehydration. The study of the optical clearing effect created by a simple mixture composed by ethanol, glycerol and distilled water has proven its effectiveness according to the variations observed in the parameters under study. The effect was characterized in terms of its magnitude, time duration and histological variations. The applied treatment has created a small reduction of the global sample refractive index that is justified by the long time rehydration caused by water in the immersing solution. From the reduction in sample pH we could also identify the dehydration process created in the sample. The immersion treatment has originated fiber bundle contraction and a spread distribution of the muscle fiber bundles inside. New studies with the mixture used, or with other combinations of its constituents might be interesting to perform with the objective to develop new clinical procedures.

  13. Rutting performance of cold bituminous emulsion mixtures

    Science.gov (United States)

    Arshad, Ahmad Kamil; Ali, Noor Azilatom; Shaffie, Ekarizan; Hashim, Wardati; Rahman, Zanariah Abd

    2017-10-01

    Cold Bituminous Emulsion Mixture (CBEM) is an environmentally friendly alternative to hot mix asphalt (HMA) for road surfacing, due to its low energy requirements. However, CBEM has generally been perceived to be less superior in performance, compared to HMA. This paper details a laboratory study on the rutting performance of CBEM. The main objective of this study is to determine the Marshall properties of CBEM and to evaluate the rutting performance. The effect of cement in CBEM was also evaluated in this study. The specimens were prepared using Marshall Mix Design Method and rutting performance was evaluated using the Asphalt Pavement Analyzer (APA). Marshall Properties were analysed to confirm compliance with the PWD Malaysia's specification requirements. The rutting performance for specimens with cement was also found to perform better than specimens without cement. It can be concluded that Cold Bituminous Emulsion Mixtures (CBEM) with cement is a viable alternative to Hot Mix Asphalt (HMA) as their Marshall Properties and performance obtained from this study meets the requirements of the specifications. It is recommended that further study be conducted on CBEM for other performance criteria such as moisture susceptibility and fatigue.

  14. Catanionic mixtures forming gemini-like amphiphiles.

    Science.gov (United States)

    Sakai, Hideki; Okabe, Yuji; Tsuchiya, Koji; Sakai, Kenichi; Abe, Masahiko

    2011-01-01

    The properties of aqueous mixtures of cationic species with alkyl dicarboxylic acid compounds have been studied. The cationic compounds used in this study were tertiary amine-type N-methyl-N-(2,3-dioxypropyl)hexadecylamine (C16amine) and quaternary ammonium-type N,N-dimethyl-N-(2,3-dioxypropyl)hexadecylammonium chloride (C16Q). The alkyl dicarboxylic acid compounds used were HOOC(CH(2))(10)COOH (C12H) and its sodium salt (C12Na). Three aqueous mixtures were examined in this study: (System I) C16amine + C12H, (System II) C16Q + C12Na, and (System III) C16Q + C12H. The solution pH was set at 12 for System III. The combination of (1)H-NMR and mass spectroscopy data has suggested that a stoichiometric complex is formed in the aqueous solutions at a mole fraction of C12H (or C12Na) = 0.33. Here, the C12H (or C12Na) molecule added to the system bridges two cationic molecules, like a spacer of gemini surfactants. In fact, the static surface tensiometry has demonstrated that the stoichiometric complex behaves as gemini-like amphiphiles in aqueous solutions. Our current study offers a possible way for easily preparing gemini surfactant systems.

  15. Thermodynamics of organic mixtures containing amines

    International Nuclear Information System (INIS)

    Gonzalez, Juan Antonio; Mozo, Ismael; Fuente, Isaias Garcia de la; Cobos, Jose Carlos

    2006-01-01

    Binary mixtures containing pyridine (PY), or 2-methylpyridine (2MPY) or 3-methylpyridine (3MPY) or 4-methylpyridine (4MPY) and an organic solvent as benzene, toluene, alkane, or 1-alkanol are investigated in the framework of DISQUAC. The corresponding interaction parameters are reported. The model describes accurately a whole set of thermodynamic properties: vapor-liquid equilibria (VLE), liquid-liquid equilibria (LLE), solid-liquid equilibria (SLE), molar excess Gibbs energies (G E ), molar excess enthalpies (H E ), molar excess heat capacities at constant pressure (C P E ) and the concentration-concentration structure factor (S CC (0)). It is remarkable that DISQUAC correctly predicts the W-shaped curve of the C P E of the pyridine + n-hexadecane system. The model can be applied successfully to mixtures with strong positive or negative deviations from the Raoult's law. DISQUAC improves the theoretical results from UNIFAC (Dortmund version). The replacement of pyridine by a methylpyridine leads to a weakening of the amine-amine interactions, ascribed to the steric effect caused by the methyl group attached to the aromatic ring. This explains that for a given solvent (alkane, 1-alkanol) H E (pyridine)>H E (methylpyridine)

  16. Thermal neutron diffusion parameters in homogeneous mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Drozdowicz, K.; Krynicka, E. [Institute of Nuclear Physics, Cracow (Poland)

    1995-12-31

    A physical background is presented for a computer program which calculates the thermal neutron diffusion parameters for homogeneous mixtures of any compounds. The macroscopic absorption, scattering and transport cross section of the mixture are defined which are generally function of the incident neutron energy. The energy-averaged neutron parameters are available when these energy dependences and the thermal neutron energy distribution are assumed. Then the averaged diffusion coefficient and the pulsed thermal neutron parameters (the absorption rare and the diffusion constant) are also defined. The absorption cross section is described by the 1/v law and deviations from this behaviour are considered. The scattering cross section can be assumed as being almost constant in the thermal neutron region (which results from the free gas model). Serious deviations are observed for hydrogen atoms bound in molecules and a special study in the paper is devoted to this problem. A certain effective scattering cross section is found in this case on a base of individual exact data for a few hydrogenous media. Approximations assumed for the average cosine of the scattering angle are also discussed. The macroscopic parameters calculated are averaged over the Maxwellian energy distribution for the thermal neutron flux. An information on the input data for the computer program is included. (author). 10 refs, 4 figs, 5 tabs.

  17. Developmental Exposure to an Environmental PCB Mixture ...

    Science.gov (United States)

    Developmental PCB exposure impairs hearing and induces brainstem audiogenic seizures in adult offspring. The degree to which this enhanced susceptibility to seizure is manifest in other brain regions has not been examined. Thus, electrical kindling of the amygdala was used to evaluate the effect of developmental exposure to an environmentally relevant PCB mixture on seizure susceptibility in the rat. Female Long-Evans rats were dosed orally with 0 or 6 mg/kg/day of the PCB mixture dissolved in corn oil vehicle during the perinatal period. On postnatal day (PND) 21, pups were weaned, and two males from each litter were randomly selected for the kindling study. As adults, the male rats were implanted bilaterally with electrodes in the basolateral amygdala. For each animal, afterdischarge (AD) thresholds in the amygdala were determined on the first day of testing followed by once daily stimulation at a standard 200 µA stimulus intensity until three stage 5 generalized seizures (GS) ensued. Developmental PCB exposure did not affect the AD threshold or total cumulative AD duration, but PCB exposure did increase the latency to behavioral manifestations of seizure propagation. PCB exposed animals required significantly more stimulations to reach stage 2 seizures compared to control animals, indicating an attenuated focal (amygdala) excitability. A delay in kindling progression from a focally stimulated limbic site stands in contrast to our previous finding of increase

  18. Equilibrium study for ternary mixtures of biodiesel

    Science.gov (United States)

    Doungsri, S.; Sookkumnerd, T.; Wongkoblap, A.; Nuchitprasittichai, A.

    2017-11-01

    The liquid-liquid equilibrium (LLE) data for the ternary mixtures of methanol + fatty acid methyl ester (FAME) + palm oil and FAME + palm oil + glycerol at various temperatures from 35 to 55°C, the tie lines and binodial curves were also investigated and plotted in the equilibrium curve. The experimental results showed that the binodial curves of methanol + FAME + palm oil depended significantly with temperature while the binodial curves of FAME + palm oil + glycerol illustrated insignificant change with temperatures. The interaction parameters between liquid pair obtained for NRTL (Nonrandom Two-Liquid) and UNIQUAC (Universal Quasi-Chemical Theory) models from the experimental data were also investigated. It was found that the correlated parameters of UNIQUAC model for system of FAME + palm oil + glycerol, denoted as a13 and a31, were 580.42K and -123.69K, respectively, while those for system of methanol + FAME + palm oil, denoted as a42 and a24, were 71.48 K and 965.57K, respectively. The ternary LLE data reported here would be beneficial for engineers and scientists to use for prediction of yield and purity of biodiesel for the production. The UNIQUAC model agreed well with the experimental data of ternary mixtures of biodiesel.

  19. Thermal neutron diffusion parameters in homogeneous mixtures

    International Nuclear Information System (INIS)

    Drozdowicz, K.; Krynicka, E.

    1995-01-01

    A physical background is presented for a computer program which calculates the thermal neutron diffusion parameters for homogeneous mixtures of any compounds. The macroscopic absorption, scattering and transport cross section of the mixture are defined which are generally function of the incident neutron energy. The energy-averaged neutron parameters are available when these energy dependences and the thermal neutron energy distribution are assumed. Then the averaged diffusion coefficient and the pulsed thermal neutron parameters (the absorption rare and the diffusion constant) are also defined. The absorption cross section is described by the 1/v law and deviations from this behaviour are considered. The scattering cross section can be assumed as being almost constant in the thermal neutron region (which results from the free gas model). Serious deviations are observed for hydrogen atoms bound in molecules and a special study in the paper is devoted to this problem. A certain effective scattering cross section is found in this case on a base of individual exact data for a few hydrogenous media. Approximations assumed for the average cosine of the scattering angle are also discussed. The macroscopic parameters calculated are averaged over the Maxwellian energy distribution for the thermal neutron flux. An information on the input data for the computer program is included. (author). 10 refs, 4 figs, 5 tabs

  20. Statistical experimental design for saltstone mixtures

    International Nuclear Information System (INIS)

    Harris, S.P.; Postles, R.L.

    1991-01-01

    We used a mixture experimental design for determining a window of operability for a process at the Savannah River Site Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. 137 Cs will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach rate properties of the supernate grout, formed from various mixes of solidified salt waste, needed to be determined. The effective diffusion coefficients for NO 3 and Cr were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag and flyash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used

  1. Use of Adhesion Promoters in Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Cihlářová Denisa

    2018-03-01

    Full Text Available The purpose of asphalt binder as a significant binder in road constructions is to permanently bind aggregates of different compositions and grain sizes. The asphalt binder itself does not have suitable adhesiveness, so after a period of time, bare grains can appear. This results in a gradual separation of the grains from an asphalt layer and the presence of potholes in a pavement. Adhesion promoters or adhesive agents are important and proven promoters in practice. They are substances mainly based on the fatty acids of polyamides which should increase the reliability of the asphalt’s binder adhesion to the aggregates, thus increasing the lifetime period of the asphalt mixture as well as its resistance to mechanical strain. The amount of a promoter or agent added to the asphalt mixture is negligible and constitutes about 0.3% of the asphalt’s binder weight. Nevertheless, even this quantity significantly increases the adhesive qualities of an asphalt binder. The article was created in cooperatation with the Slovak University of Technology, in Bratislava, Slovakia, and focuses on proving the new AD2 adhesive additive and comparing it with the Addibit and Wetfix BE promoters used on aggregates from the Skuteč - Litická and Bystřec quarries.

  2. Phase equilibria in chemical reactive fluid mixtures

    International Nuclear Information System (INIS)

    Maurer, Gerd

    2011-01-01

    Downstream processing is a major part of nearly all processes in the chemical industries. Most separation processes in the chemical (and related) industries for fluid mixtures are based on phase equilibrium phenomena. The majority of separation processes can be modelled assuming that chemical reactions are of no (or very minor) importance, i.e., assuming that the overall speciation remains unchanged during a separation process. However, there are also a large number of industrially important processes where the thermodynamic properties are influenced by chemical reactions. The phase equilibrium of chemical reactive mixtures has been a major research area of the author's group over nearly 40 years. In this contribution, three examples from that research are discussed. The first example deals with the vapour phase dimerisation of carboxylic acids and its consequences on phase equilibrium phenomena and phase equilibrium predictions. The second example deals with the solubility of sour gases (e.g., carbon dioxide and sulfur dioxide) in aqueous solutions of ammonia. That topic has been of interest for many years, e.g., in relation with the gasification and liquefaction of coal and, more recently, with the removal of carbon dioxide from flue gas in the 'chilled ammonia process'. The third example deals with phase equilibrium phenomena in aqueous solutions of polyelectrolytes. It deals with the phenomenon of 'counter ion condensation' and methods to model the Gibbs free energy of such solutions.

  3. Effect of Fibers on Mixture Design of Stone Matrix Asphalt

    Directory of Open Access Journals (Sweden)

    Yanping Sheng

    2017-03-01

    Full Text Available Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA, such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber. The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV, Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

  4. Theoretical study of the paramagnetic scattering of neutrons; Etude theorique de la diffusion paramagnetique des neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Saint-James, D [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1962-02-15

    diverses diffusions (elastique et inelastiques) est calculee pour les terres rares soumises a l'action d'un champ cristallin de symetrie cubique, pour les sesquioxydes d'holmium et d'erbium et pour le chlorure ferreux anhydre (Cl{sub 2}Fe). Elle est suffisamment forte pour permettre une detection experimentale, fournissant ainsi une determination directe de la distance des niveaux par mesure de la variation de longueur d'onde du neutron. Il est, de plus, remarquable que, dans le cas du neodyme, de l'holium et de l'erbium, la section efficace totale calculee pour des neutrons de longueur d'onde aux alentours de l'angstrom soit peu sensible aux effets du champ cristallin. On compare les resultats des calculs ci-dessus aux etudes experimentales existantes. On examine egalement l'influence du moment orbital sur la dependance angulaire de la diffusion pour des ions polarises. La loi I = I{sub 0}sin{sup 2}{beta} n'est qu'approchee; on en donne les limites de validite. On envisage enfin l'influence des interactions d'echange entre les ions magnetiques. Les raies de diffusion elastiques et inelastiques sont elargies. Le comportement de la largeur de raie, avec la longueur du vecteur de diffusion k, est different de celui obtenu dans le cas ou le niveau fondamental de l'ion magnetique est defini par un moment cinetique J . La largeur de raie ne tend pas vers zero avec K. (auteur)

  5. Electron cloud sizes in gas-filled detectors

    International Nuclear Information System (INIS)

    Boggende, A.J.F. den; Schrijver, C.J.

    1984-01-01

    Electron cloud sizes have been calculated for gas mixtures containing Ar, Xe, CO 2 , CH 4 , and N 2 for drifts through a constant electric field. The transport coefficients w and D/μ are in good agreement with experimental data of various sources for pure gases. Results of measurements, also performed in this work, for Ar+CO 2 , Ar+CH 4 , and Ar+Xe+CO 2 mixtures are in fair agreement with the calculated cloud sizes. For a large number of useful gas mixtures calculated electron cloud sizes are presented and discussed, most of which are given for the first time. A suggestion is made for an optimal gas mixture for an X-ray position sensitive proportional counter for medium and low energies. (orig.)

  6. Stochastic radiative transfer model for mixture of discontinuous vegetation canopies

    International Nuclear Information System (INIS)

    Shabanov, Nikolay V.; Huang, D.; Knjazikhin, Y.; Dickinson, R.E.; Myneni, Ranga B.

    2007-01-01

    Modeling of the radiation regime of a mixture of vegetation species is a fundamental problem of the Earth's land remote sensing and climate applications. The major existing approaches, including the linear mixture model and the turbid medium (TM) mixture radiative transfer model, provide only an approximate solution to this problem. In this study, we developed the stochastic mixture radiative transfer (SMRT) model, a mathematically exact tool to evaluate radiation regime in a natural canopy with spatially varying optical properties, that is, canopy, which exhibits a structured mixture of vegetation species and gaps. The model solves for the radiation quantities, direct input to the remote sensing/climate applications: mean radiation fluxes over whole mixture and over individual species. The canopy structure is parameterized in the SMRT model in terms of two stochastic moments: the probability of finding species and the conditional pair-correlation of species. The second moment is responsible for the 3D radiation effects, namely, radiation streaming through gaps without interaction with vegetation and variation of the radiation fluxes between different species. We performed analytical and numerical analysis of the radiation effects, simulated with the SMRT model for the three cases of canopy structure: (a) non-ordered mixture of species and gaps (TM); (b) ordered mixture of species without gaps; and (c) ordered mixture of species with gaps. The analysis indicates that the variation of radiation fluxes between different species is proportional to the variation of species optical properties (leaf albedo, density of foliage, etc.) Gaps introduce significant disturbance to the radiation regime in the canopy as their optical properties constitute major contrast to those of any vegetation species. The SMRT model resolves deficiencies of the major existing mixture models: ignorance of species radiation coupling via multiple scattering of photons (the linear mixture model

  7. Contribution to the study of samarium-151 excited levels; Contribution a l'etude des niveaux excites du samarium-151

    Energy Technology Data Exchange (ETDEWEB)

    Locard, P [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Grenoble, 38 (France)

    1967-07-01

    The nucleus of {sup 151}Sm, which has 89 neutrons, happens to be on the lower edge of the deformed nuclei of region II. Therefore, the study of its levels is very interesting for the verification of the goodness of the collective models for deformed nuclei when the deformation is small (we introduce these models in the first chapter). {sup 151}Sm has often been studied, but the direct gamma spectrum measured with a lithium drift-germanium detector (chapter 3) shows many high energy transitions which did not appear in the previous level schemes. In order to settle these transitions, we have undertaken gamma-gamma coincidence spectra (as well as sum-coincidence spectra) experiments with a scintillation spectrometer designed in our laboratory (chapter 2). The investigation of the intensities of these coincidences leads us to modify the last proposed level schemes: we suppress the levels at 405,5 and 650 keV, we add levels at 245,6 - 306,6 - 522 - 952 and 962 keV. We have also verified the multipolarities of the main transitions and measured the half-lives of a few levels (chapter 3) (we find a half-life of 1.1 {+-} 0.5 nanosecond for the level at 167,7 keV). In chapter 4, we compare our results to the predictions of the models described in chapter 1. (author) [French] Le noyau de {sup 151}Sm, qui possede 89 neutrons, se trouve a la limite inferieure des noyaux deformes de la region II. L'etude de ses niveaux excites est donc d'un interet tout particulier pour la verification de la validite des differents modeles collectifs pour les noyaux deformes, lorsque la deformation est petite (nous introduisons ces modeles dans un premier chapitre). Le {sup 151}Sm a deja fait l'objet de nombreuses etudes, mais le spectre gamma direct fait avec une jonction de germanium compense au lithium (chapitre 3), nous a montre l'existence d'un grand nombre de transitions de hautes energies qui ne sont pas placees dans les schemas proposes jusqu'a ce jour. Pour preciser la place de ces

  8. Urea and deuterium mixtures at high pressures

    Energy Technology Data Exchange (ETDEWEB)

    Donnelly, M., E-mail: m.donnelly-2@sms.ed.ac.uk; Husband, R. J.; Frantzana, A. D.; Loveday, J. S. [Centre for Science at Extreme Conditions and School of Physics and Astronomy, The University of Edinburgh, Erskine Williamson Building, Peter Guthrie Tait Road, The King’s Buildings, Edinburgh EH9 3FD (United Kingdom); Bull, C. L. [ISIS, Rutherford Appleton Laboratory, Oxford Harwell, Didcot OX11 0QX (United Kingdom); Klotz, S. [IMPMC, CNRS UMR 7590, Université P and M Curie, 4 Place Jussieu, 75252 Paris (France)

    2015-03-28

    Urea, like many network forming compounds, has long been known to form inclusion (guest-host) compounds. Unlike other network formers like water, urea is not known to form such inclusion compounds with simple molecules like hydrogen. Such compounds if they existed would be of interest both for the fundamental insight they provide into molecular bonding and as potential gas storage systems. Urea has been proposed as a potential hydrogen storage material [T. A. Strobel et al., Chem. Phys. Lett. 478, 97 (2009)]. Here, we report the results of high-pressure neutron diffraction studies of urea and D{sub 2} mixtures that indicate no inclusion compound forms up to 3.7 GPa.

  9. Coke from partially briquetted preheated coal mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Belitskii, A.N.; Sklyar, M.G.; Toryanik, Eh.I.; Bronshtein, A.P.

    1988-07-01

    Analyzes effects of partial coal charge briquetting on coking and on quality of coke for metallurgy. Effects of mixing hot coal briquets on temperature and moisture of coal were investigated on an experimental scale in a coking plant. Coal with a moisture content of 12% was used. Coking mixture consisted of 30% briquets and 70% crushed coal. Fifteen minutes after briquet mixing with coal, the mean coal charge temperature increased to 100-105 C and moisture content was lower than 2-5%. Results of laboratory investigations were verified by tests on a commercial scale. Experiments showed briquetting of weakly caking or non-caking coal charge components to be an efficient way of preventing coke quality decline. Adding 15-20% briquets consisting of weakly caking coal did not influence coke quality. Mixing hot coal briquets reduced moisture content in crushed coal, increased its temperature and reduced coking time.

  10. Radiative otacity tables for 40 stellar mixtures

    International Nuclear Information System (INIS)

    Cox, A.N.; Tabor, J.E.

    1976-01-01

    Using improved methods, radiative opacities for 40 mixtures of elements are given for use in calculations of stellar structure, stellar evolution, and stellar pulsation. The major improvements over previous Los Alamos data are increased iron abundance in the composition, better allowance for the continuum depression for bound electrons, and corrections in some bound-electron energy levels. These opacities have already been widely used, and represent a relatively homogeneous set of data for stellar structures. Further improvements to include more bound-bound (line) transitions by a smearing technique and to include molecular absorptions are becoming available, and in a few years these tables, as well as all previous tables, will be outdated. At high densities the conduction of energy will dominate radiation flow, and this effect must be added separately

  11. Wetting and evaporation of binary mixture drops.

    Science.gov (United States)

    Sefiane, Khellil; David, Samuel; Shanahan, Martin E R

    2008-09-11

    Experimental results on the wetting behavior of water, methanol, and binary mixture sessile drops on a smooth, polymer-coated substrate are reported. The wetting behavior of evaporating water/methanol drops was also studied in a water-saturated environment. Drop parameters (contact angle, shape, and volume) were monitored in time. The effects of the initial relative concentrations on subsequent evaporation and wetting dynamics were investigated. Physical mechanisms responsible for the various types of wetting behavior during different stages are proposed and discussed. Competition between evaporation and hydrodynamic flow are evoked. Using an environment saturated with water vapor allowed further exploration of the controlling mechanisms and underlying processes. Wetting stages attributed to differential evaporation of methanol were identified. Methanol, the more volatile component, evaporates predominantly in the initial stage. The data, however, suggest that a small proportion of methanol remained in the drop after the first stage of evaporation. This residual methanol within the drop seems to influence subsequent wetting behavior strongly.

  12. CRITICALITY CURVES FOR PLUTONIUM HYDRAULIC FLUID MIXTURES

    International Nuclear Information System (INIS)

    WITTEKIND WD

    2007-01-01

    This Calculation Note performs and documents MCNP criticality calculations for plutonium (100% 239 Pu) hydraulic fluid mixtures. Spherical geometry was used for these generalized criticality safety calculations and three geometries of neutron reflection are: (sm b ullet)bare, (sm b ullet)1 inch of hydraulic fluid, or (sm b ullet)12 inches of hydraulic fluid. This document shows the critical volume and critical mass for various concentrations of plutonium in hydraulic fluid. Between 1 and 2 gallons of hydraulic fluid were discovered in the bottom of HA-23S. This HA-23S hydraulic fluid was reported by engineering to be Fyrquel 220. The hydraulic fluid in GLovebox HA-23S is Fyrquel 220 which contains phosphorus. Critical spherical geometry in air is calculated with 0 in., 1 in., or 12 inches hydraulic fluid reflection

  13. Bioavailability and variability of biphasic insulin mixtures

    DEFF Research Database (Denmark)

    Søeborg, Tue; Rasmussen, Christian Hove; Mosekilde, Erik

    2012-01-01

    Absorption of subcutaneously administered insulin is associated with considerable variability. Some of this variability was quantitatively explained for both soluble insulin and insulin suspensions in a recent contribution to this journal (Søeborg et al., 2009). In the present article......, the absorption kinetics for mixtures of insulins is described. This requires that the bioavailability of the different insulins is considered. A short review of insulin bioavailability and a description of the subcutaneous depot thus precede the presentation of possible mechanisms associated with subcutaneous...... insulin degradation. Soluble insulins are assumed to be degraded enzymatically in the subcutaneous tissue. Suspended insulin crystals form condensed heaps that are assumed to be degraded from their surface by invading macrophages. It is demonstrated how the shape of the heaps affects the absorption...

  14. Dynamics of binary mixtures in inhomogeneous temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Gonnella, G; Piscitelli, A [Dipartimento di Fisica, Universita di Bari and Istituto Nazionale di Fisica Nucleare, Sezione di Bari, via Amendola 173, 70126 Bari (Italy); Lamura, A [Istituto Applicazioni Calcolo, CNR, via Amendola 122/D, 70126 Bari (Italy)

    2008-03-14

    A dynamical description for fluid binary mixtures with variable temperature and concentration gradient contributions to entropy and internal energy is given. By using mass, momentum and energy balance equations together with the standard expression for entropy production, a generalized Gibbs-Duhem relation is obtained which takes into account thermal and concentration gradient contributions. Then an expression for the pressure tensor is derived. As examples of applications, interface behavior and phase separation have been numerically studied in two dimensions neglecting the contributions of the velocity field. In the simplest case with a constant thermal gradient, the growth exponent for the averaged size of domains is found to have the usual value z = 1/3 and the domains appear elongated in the direction of the thermal gradient. When the system is quenched by contact with external walls, the evolution of temperature profiles in the system is shown and the domain morphology is characterized by interfaces perpendicular to the thermal gradient.

  15. Performance of asphalt mixture incorporating recycled waste

    Science.gov (United States)

    Hamid, Nor Baizura; Abdullah, Mohd Ezree; Sanik, Mohd Erwan; Mokhtar, Mardiha; Kaamin, Masiri; Raduan, Rasyidah; Ramli, Mohd Zakwan

    2017-12-01

    Nowadays, the amount of premix waste was increased every year, especially at the batching plants. Normally, the waste materials will be discarded without doing any innovative and effective research about those materials. This situation has become one of the global concerns due to the increasing number of premix waste produced every year. Therefore, the aim of this study is to evaluate the performance of hot mix asphalt (HMA) using premix waste on improving asphalt mixture fatigue behaviour. The method used in this study was Superpave mix design method. The sample conducted in this study were 0%, 10%, 20%, 30%, and 100% of premix waste respectively. For a binder test, the laboratory test conducted were penetration test, softening test and thin film oven test while for the performance test were resilient modulus test and indirect tensile fatigue test. From the laboratory test, the resilient modulus test was conducted with two different temperature which was 25°C and 40°C. The result from that test was 20% of premix waste had higher resilient modulus at that two different temperatures compared to another samples. From that test also shown that the sample at the lower temperature which was 25°C has higher resilient modulus compared to the temperature of 40°C. Indirect tensile fatigue test showed that the 30% of premix waste sample was suitable for the modified asphalt mixture with referring to the maximum deformation and strain for comparison control, 10%,20%, and 100% of premix waste samples. So, it can be concluded that premix waste inhibits great potential as road construction material and suitable for repeated traffic loading.

  16. Ostwald ripening in two-phase mixtures

    International Nuclear Information System (INIS)

    Voorhees, P.W.

    1982-01-01

    Experimental measurements of the temperature of a rapidly solidified solid-liquid mixture have been made over a range of volume fractions solid 0.23 to 0.95. These experiments demonstrate the viability of measuring the change in interfacial curvature with time via precision thermometry. The experimental measurements also indicate that there is no radical change in interface morphology over a wide range of volume fractions solid. A solution to the multi-particle diffusion problem (MDP) has been constructed through the use of potential theory. The solution to the MDP was used to describe the diffusion field within a coarsening two-phase mixture consisting of dispersed spherical second-phase particles. Since this theory is based upon the MDP, interparticle diffusional interactions are specifically included in the treatment. As a result, the theory yields, for the first time, insights into the influence of the local distribution of curvature on a particle's coarsening rate. The effect of interparticle interactions on the collective behavior of an ensemble of coarsening particles was also investigated. It was found that any arbitrary distribution of particle radii will tend to a specific time independent distribution when the particle radii are scaled by the average particle radius. Furthermore, it was determined that with increasing volume fraction of coarsening phase, these time independent distributions become broader and more symmetric. It was also found that the ripening kinetics, as measured by the growth rate of the average particle size, increases by a factor of five upon increasing the volume fraction of coarsening phase from zero to 0.5

  17. Structure of two-phase air-water flows. Study of average void fraction and flow patterns; Structure des ecoulements diphasiques eau-air. Etude de la fraction de vide moyenne et des configurations d'ecoulement

    Energy Technology Data Exchange (ETDEWEB)

    Roumy, R [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1969-07-01

    This report deals with experimental work on a two phase air-water mixture in vertical tubes of different diameters. The average void fraction was measured in a 2 metre long test section by means of quick-closing valves. Using resistive probes and photographic techniques, we have determined the flow patterns and developed diagrams to indicate the boundaries between the various patterns: independent bubbles, agglomerated bubbles, slugs, semi-annular, annular. In the case of bubble flow and slug flow, it is shown that the relationship between the average void fraction and the superficial velocities of the phases is given by: V{sub sg} = f(<{alpha}>) * g(V{sub sl}). The function g(V{sub sl}) for the case of independent bubbles has been found to be: g(V{sub sl}) = V{sub sl} + 20. For semi-annular and annular flow conditions; it appears that the average void fraction depends, to a first approximation only on the ratio V{sub sg}/V{sub sl}. (author) [French] Ce rapport est une etude experimentale d'un melange diphasique eau-air dans des tubes verticaux de differents diametres. Nous avons mesure la fraction de vide moyenne dans une portion de canal de longueur 2 m, au moyen d'un systeme de vannes a fermeture rapide et simultanee. Au moyen de sondes resistives et de photographies nous avons determine la configuration de l'ecoulement et trace des cartes donnant les frontieres entre les differentes configurations d'ecoulement: bulles independantes, bulles agglomerees, bouchons, semi-annulaire, annulaire. Nous montrons que pour les regimes a bulles et a bouchons, une equation de la forme V{sub sg} = f(<{alpha}>) * g(V{sub sl}) relie la fraction de vide moyenne aux vitesses superficielles de chacune des phases. Nous avons pu determiner la fonction g(V{sub sl}) dans le cas du regime a bulles independantes, et nous trouvons g(V{sub sl}) = V{sub sl} + 20. Pour les regimes semi-annulaire et annulaire, il semble qu'en premiere approximation, la fraction de vide moyenne ne depende que

  18. Maximum likelihood estimation of finite mixture model for economic data

    Science.gov (United States)

    Phoong, Seuk-Yen; Ismail, Mohd Tahir

    2014-06-01

    Finite mixture model is a mixture model with finite-dimension. This models are provides a natural representation of heterogeneity in a finite number of latent classes. In addition, finite mixture models also known as latent class models or unsupervised learning models. Recently, maximum likelihood estimation fitted finite mixture models has greatly drawn statistician's attention. The main reason is because maximum likelihood estimation is a powerful statistical method which provides consistent findings as the sample sizes increases to infinity. Thus, the application of maximum likelihood estimation is used to fit finite mixture model in the present paper in order to explore the relationship between nonlinear economic data. In this paper, a two-component normal mixture model is fitted by maximum likelihood estimation in order to investigate the relationship among stock market price and rubber price for sampled countries. Results described that there is a negative effect among rubber price and stock market price for Malaysia, Thailand, Philippines and Indonesia.

  19. Thermal analysis of pyrotechnic mixture-fireworks, atom-bomb

    International Nuclear Information System (INIS)

    Rajendran, Jeya; Thanulingam, T.L.

    2008-01-01

    Sound level produced from two varieties of sound producing fireworks of atom-bomb, cake bomb and thunder bomb were measured. The pyrotechnic mixture, KNO 3 /S/Al(H 3 BO 3 ) of compositions 57.5/19.9/22.1(0.5)% very much similar to commercial atom-bomb were taken and five cake bomb and seven thunder bomb with different net weight of chemicals were manufactured specifically for analysis. Cake bomb with 1g pyrotechnic mixture and thunder bomb with 2g pyrotechnic mixture produce -3 . Ignition temperature of the mixture is above the melting point of the metallic fuel, Al (660 deg C) and self propagating decomposition occurred at high temperature. The pyrotechnic mixture, KNO 3 /S/Al(H 3 BO 3 ) is a safe mixture from accidental factor, static electricity. DSC studies indicate slight formation of potassium nitrite with evolution of NO above 400 deg C. (author)

  20. Azide-based cross-linking of polymers of intrinsic microporosity (PIMs) for condensable gas separation

    KAUST Repository

    Du, Naiying; Dal-Cin, Mauro M D; Pinnau, Ingo; Nicalek, Andrzej; Robertson, Gilles P.; Guiver, Michael D.

    2011-01-01

    Cross-linked polymers of intrinsic microporosity (PIM)s for gas separation membranes, were prepared by a nitrene reaction from a representative PIM in the presence of two different diazide cross-linkers. The reaction temperature was optimized using TGA. The homogenous membranes were cast from THF solutions of different ratios of PIM to azides. The resulting cross-linked structures of the PIMs membranes were formed at 175 °C after 7.5 h and confirmed by TGA, XPS, FT-IR spectroscopy and gel content analysis. These resulting cross-linked polymeric membranes showed excellent gas separation performance and can be used for O 2/N 2 and CO 2/N 2 gas pairs, as well as for condensable gases, such as CO 2/CH 4, propylene/propane separation. Most importantly, and differently from typical gas separation membranes derived from glassy polymers, the crosslinked PIMs showed no obvious CO 2 plasticization up to 20 atm pressure of pure CO 2 and CO 2/CH 4 mixtures. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Azide-based cross-linking of polymers of intrinsic microporosity (PIMs) for condensable gas separation

    KAUST Repository

    Du, Naiying

    2011-03-11

    Cross-linked polymers of intrinsic microporosity (PIM)s for gas separation membranes, were prepared by a nitrene reaction from a representative PIM in the presence of two different diazide cross-linkers. The reaction temperature was optimized using TGA. The homogenous membranes were cast from THF solutions of different ratios of PIM to azides. The resulting cross-linked structures of the PIMs membranes were formed at 175 °C after 7.5 h and confirmed by TGA, XPS, FT-IR spectroscopy and gel content analysis. These resulting cross-linked polymeric membranes showed excellent gas separation performance and can be used for O 2/N 2 and CO 2/N 2 gas pairs, as well as for condensable gases, such as CO 2/CH 4, propylene/propane separation. Most importantly, and differently from typical gas separation membranes derived from glassy polymers, the crosslinked PIMs showed no obvious CO 2 plasticization up to 20 atm pressure of pure CO 2 and CO 2/CH 4 mixtures. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Multicomponent Matrimid Membrane for Gas Separation

    KAUST Repository

    Irerua, Olayinka

    2012-07-01

    Matrimid was utilized for the preparation of membranes with asymmetric structures. A combination of well-known solvents for Matrimid which include 1- methyl-2-Pyrrolidone (NMP), tetrahydrofuran (THF), dichloromethane, tetrachloroethane as well as non-solvents n-butanol, xylene, and acetic acid were used. Cast solutions were prepared at room temperature for different combinations and compositions of polymer/solvent/non-solvent systems. PEG and Octa-(amino phenyl) POSS were introduced in some of the cast solutions. The membranes obtained were characterized by permeation test for gas permeabilities and selectivities, Scanning Electron Microscopy (SEM) and Nuclear Magnetic Resonance (NMR) Spectroscopy. The gas permeation test showed that the use of mixture of dichloromethane and tetrachloroethane as solvents with xylene non-solvent and acetic acid as stabilizer gave membranes with very high gas selectivity of 133 for CO2/N2 and 492 for CO2/CH4. Also, cast solutions containing PEG resulted in membranes with slightly enhanced selectivities from 30 to 42 for CO2/N2. Permeation results for CO2, N2 and H2 and the selectivities for gas pairs such as CO2/N2, CO2/CH4, are discussed in relation to the effect of pressure on the membrane permeance, they are also compared with existing results.

  3. Aerodynamic and thermal studies of cans of gas cooled fuel elements; Etudes aerodynamiques et thermiques de gaines d'elements combustibles refroidis par gaz

    Energy Technology Data Exchange (ETDEWEB)

    Gelin, P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Milliat, J P [Electricite de France (EDF), 75 - Paris (France)

    1964-07-01

    Research on clusters was undertaken at the CEA in 1959, while studies on herring-bone cans were developed at the EDF Laboratory at Chatou and the CEA laboratory at Saclay at the end of 1959. In 1962, a general study on corrugations was begun at the Saclay Laboratory with a view to improving the clusters, and continued later in both laboratories relative to the internal cooling of annular fuel elements. As these studies progressed, trial facilities were extended while experimental methods have improved constantly. At the present time, both laboratories, working in complete collaboration, have powerful means at their disposal. Work on the clusters has been concerned chiefly with pressure losses due to the assembly parts, and with the temperature variations around the elements of the cluster. In this way, we have been able to determine satisfactorily the hot points of the can, the deformations of the rods and the conditions of stability of these deformations. In the case of the herring-bone cans, studies have been directed to the evolution of performances as a function of the geometric parameters on the one hand, and to the special aerodynamic and thermal features caused by the fins and by interruptions of cartridge on the other hand. These studies have led to a very thorough knowledge of the cartridges chosen for the reactors EDF 2 and EDF 3, and now open up very hopeful prospects for future reactors, particularly those fitted with annular elements; among the alternatives suitable for the inner surface of the annular element can, corrugations and longitudinal fins have been fairly extensively tested over a wide range of Reynolds number. (authors) [French] Les etudes de grappes ont ete entreprises au C.E.A. en 1959, tandis que les etudes de gaines a chevrons se sont developpees au Laboratoire de Chatou de l'EDF et au Laboratoire de Saclay du C.E.A. a la fin de l'annee 1959. En 1962, une etude generale sur les corrugations a ete commencee au Laboratoire de Saclay pour

  4. Antiandrogenic activity of phthalate mixtures: Validity of concentration addition

    International Nuclear Information System (INIS)

    Christen, Verena; Crettaz, Pierre; Oberli-Schrämmli, Aurelia; Fent, Karl

    2012-01-01

    Phthalates and bisphenol A have very widespread use leading to significant exposure of humans. They are suspected to interfere with the endocrine system, including the androgen, estrogen and the thyroid hormone system. Here we analyzed the antiandrogenic activity of six binary, and one ternary mixture of phthalates exhibiting complete antiandrogenic dose–response curves, and binary mixtures of phthalates and bisphenol A at equi-effective concentrations of EC 10 , EC 25 and EC 50 in MDA-kb2 cells. Mixture activity followed the concentration addition (CA) model with a tendency to synergism at high and antagonism at low concentrations. Isoboles and the toxic unit approach (TUA) confirmed the additive to synergistic activity of the binary mixtures BBP + DBP, DBP + DEP and DEP + BPA at high concentrations. Both methods indicate a tendency to antagonism for the EC 10 mixtures BBP + DBP, BBP + DEP and DBP + DEP, and the EC 25 mixture of DBP + BPA. A ternary mixture revealed synergism at the EC 50 , and weak antagonistic activity at the EC 25 level by the TUA. A mixture of five phthalates representing a human urine composition and reflecting exposure to corresponding parent compounds showed no antiandrogenic activity. Our study demonstrates that CA is an appropriate concept to account for mixture effects of antiandrogenic phthalates and bisphenol A. The interaction indicates a departure from additivity to antagonism at low concentrations, probably due to interaction with the androgen receptor and/or cofactors. This study emphasizes that a risk assessment of phthalates should account for mixture effects by applying the CA concept. -- Highlights: ► Antiandrogenic activity of mixtures of 2 and 3 phthalates are assessed in MDA-kb2 cells. ► Mixture activities followed the concentration addition model. ► A tendency to synergism at high and antagonism at low levels occurred.

  5. Antiandrogenic activity of phthalate mixtures: Validity of concentration addition

    Energy Technology Data Exchange (ETDEWEB)

    Christen, Verena [University of Applied Sciences Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Crettaz, Pierre; Oberli-Schrämmli, Aurelia [Swiss Federal Office of Public Health, Division Chemical Products, 3003 Bern (Switzerland); Fent, Karl, E-mail: karl.fent@bluewin.ch [University of Applied Sciences Northwestern Switzerland, School of Life Sciences, Gründenstrasse 40, CH-4132 Muttenz (Switzerland); Swiss Federal Institute of Technology Zürich (ETH Zürich), Department of Environmental Sciences, 8092 Zürich (Switzerland)

    2012-03-01

    Phthalates and bisphenol A have very widespread use leading to significant exposure of humans. They are suspected to interfere with the endocrine system, including the androgen, estrogen and the thyroid hormone system. Here we analyzed the antiandrogenic activity of six binary, and one ternary mixture of phthalates exhibiting complete antiandrogenic dose–response curves, and binary mixtures of phthalates and bisphenol A at equi-effective concentrations of EC{sub 10}, EC{sub 25} and EC{sub 50} in MDA-kb2 cells. Mixture activity followed the concentration addition (CA) model with a tendency to synergism at high and antagonism at low concentrations. Isoboles and the toxic unit approach (TUA) confirmed the additive to synergistic activity of the binary mixtures BBP + DBP, DBP + DEP and DEP + BPA at high concentrations. Both methods indicate a tendency to antagonism for the EC{sub 10} mixtures BBP + DBP, BBP + DEP and DBP + DEP, and the EC{sub 25} mixture of DBP + BPA. A ternary mixture revealed synergism at the EC{sub 50}, and weak antagonistic activity at the EC{sub 25} level by the TUA. A mixture of five phthalates representing a human urine composition and reflecting exposure to corresponding parent compounds showed no antiandrogenic activity. Our study demonstrates that CA is an appropriate concept to account for mixture effects of antiandrogenic phthalates and bisphenol A. The interaction indicates a departure from additivity to antagonism at low concentrations, probably due to interaction with the androgen receptor and/or cofactors. This study emphasizes that a risk assessment of phthalates should account for mixture effects by applying the CA concept. -- Highlights: ► Antiandrogenic activity of mixtures of 2 and 3 phthalates are assessed in MDA-kb2 cells. ► Mixture activities followed the concentration addition model. ► A tendency to synergism at high and antagonism at low levels occurred.

  6. DURABILITY OF ASPHALT CONCRETE MIXTURES USING DOLOMITE AGGREGATES

    Directory of Open Access Journals (Sweden)

    Imad Al-Shalout

    2015-12-01

    Full Text Available This study deals with the durability of asphalt concrete, including the effects of different gradations, compaction temperatures and immersion time on the durability potential of mixtures. The specific objectives of this study are: to investigate the effect of compaction temperature on the mechanical properties of asphalt concrete mixtures; investigate the effect of bitumen content and different aggregate gradations on the durability potential of bituminous mixtures.

  7. Genetic Evidence for Recent Population Mixture in India

    OpenAIRE

    Moorjani, Priya; Thangaraj, Kumarasamy; Patterson, Nick; Lipson, Mark; Loh, Po-Ru; Govindaraj, Periyasamy; Berger, Bonnie; Reich, David; Singh, Lalji

    2013-01-01

    Most Indian groups descend from a mixture of two genetically divergent populations: Ancestral North Indians (ANI) related to Central Asians, Middle Easterners, Caucasians, and Europeans; and Ancestral South Indians (ASI) not closely related to groups outside the subcontinent. The date of mixture is unknown but has implications for understanding Indian history. We report genome-wide data from 73 groups from the Indian subcontinent and analyze linkage disequilibrium to estimate ANI-ASI mixture ...

  8. Mixture of Regression Models with Single-Index

    OpenAIRE

    Xiang, Sijia; Yao, Weixin

    2016-01-01

    In this article, we propose a class of semiparametric mixture regression models with single-index. We argue that many recently proposed semiparametric/nonparametric mixture regression models can be considered special cases of the proposed model. However, unlike existing semiparametric mixture regression models, the new pro- posed model can easily incorporate multivariate predictors into the nonparametric components. Backfitting estimates and the corresponding algorithms have been proposed for...

  9. Determination of thermal conductivity in foundry mould mixtures

    Directory of Open Access Journals (Sweden)

    G. Solenički

    2010-01-01

    Full Text Available For a thorough understanding of the behaviour of foundry mould mixtures, a good knowledge of thermal properties of mould materials is needed. Laboratory determination of thermal conductivity of mould mixtures enables a better control over scabbing defects which are a major problem in green sand mould mixtures. A special instrument has been designed for that purpose and it is described in this work.

  10. UTILIZATION OF WASTE PLASTIC BOTTLES IN ASPHALT MIXTURE

    Directory of Open Access Journals (Sweden)

    TAHER BAGHAEE MOGHADDAM

    2013-06-01

    Full Text Available Nowadays, large amounts of waste materials are being produced in the world. One of the waste materials is plastic bottle. Generating disposable plastic bottles is becoming a major problem in many countries. Using waste plastic as a secondary material in construction projects would be a solution to overcome the crisis of producing large amount of waste plastics in one hand and improving the structure’s characteristics such as resistance against cracking on the other hand. This study aimed to investigate the effects of adding plastic bottles in road pavement. Marshall properties as well as specific gravity of asphalt mixture containing different percentages of plastic bottles were evaluated. Besides, Optimum Asphalt Content (OAC was calculated for each percentages of plastic bottles used in the mix. The stiffness and fatigue characteristics of mixture were assessed at OAC value. Results showed that the stability and flow values of asphalt mixture increased by adding waste crushed plastic bottle into the asphalt mixture. Further, it was shown that the bulk specific gravity and stiffness of mixtures increased by adding lower amount of plastic bottles; however, adding higher amounts of plastic resulted in lower specific gravity and mix stiffness. In addition, it was concluded that the mixtures containing waste plastic bottles have lower OAC values compared to the conventional mixture, and this may reduce the amount of asphalt binder can be used in road construction projects. Besides, the mixtures containing waste plastic showed significantly greater fatigue resistance than the conventional mixture.

  11. Self-flowing underwater concrete mixtures for high rise structures

    International Nuclear Information System (INIS)

    Yousri, K.M.

    2005-01-01

    Placement of conventional concrete mixtures in underwater construction results in a high percentage of material loss due to washout of cement paste. This paper presents the influence of anti washout admixture (AWA) on various properties of concrete. Eleven self-flowing concrete (SFC) mixtures using type II cement were proportioned. A combination of low water cement (w/c), high cement contents, anti washout admixtures, fly ash, and silica fume were used to enhance the resistance of fresh concrete to washout. The concrete mixtures proportioned to be highly flow able, self-leveling and cohesive. The water-cementitious materials ratios ranged between 0.356 and 0.392 which correspond a typical underwater concrete mixture. The concrete mixtures were tested for slump, slump flow, washout resistance and compressive strength. The compressive strength of each concrete mixture cast underwater was determined at 3, 7, 28 days and compared with the compressive strength of the same concrete mixture cast in normal condition (in air). Test results indicated that the use of an AWA facilitates the production of flow able concrete mixtures with the added benefit of lower washout loss. Concrete mixture proportioned using Type II cement and fly ash at level of replacement of 15% was found to develop self flowing concrete with better fresh and hardened properties and more resistant to washout. The self-flowing underwater concretes developed a 28-day compressive strengths ranging from 20 to 28 MPa

  12. Communication: Modeling electrolyte mixtures with concentration dependent dielectric permittivity

    Science.gov (United States)

    Chen, Hsieh; Panagiotopoulos, Athanassios Z.

    2018-01-01

    We report a new implicit-solvent simulation model for electrolyte mixtures based on the concept of concentration dependent dielectric permittivity. A combining rule is found to predict the dielectric permittivity of electrolyte mixtures based on the experimentally measured dielectric permittivity for pure electrolytes as well as the mole fractions of the electrolytes in mixtures. Using grand canonical Monte Carlo simulations, we demonstrate that this approach allows us to accurately reproduce the mean ionic activity coefficients of NaCl in NaCl-CaCl2 mixtures at ionic strengths up to I = 3M. These results are important for thermodynamic studies of geologically relevant brines and physiological fluids.

  13. Gas Mixtures for Welding with Micro-Jet Cooling

    Directory of Open Access Journals (Sweden)

    Węgrzyn T.

    2015-04-01

    Full Text Available Welding with micro-jet cooling after was tested only for MIG and MAG processes. For micro-jet gases was tested only argon, helium and nitrogen. A paper presents a piece of information about gas mixtures for micro-jet cooling after in welding. There are put down information about gas mixtures that could be chosen both for MAG welding and for micro-jet process. There were given main information about influence of various micro-jet gas mixtures on metallographic structure of steel welds. Mechanical properties of weld was presented in terms of various gas mixtures selection for micro-jet cooling.

  14. Plastic Bottles Waste Utilization as Modifier for Asphalt Mixture Production

    Directory of Open Access Journals (Sweden)

    Jan Hakeem

    2017-01-01

    Full Text Available Plastic Bottles was used as the polymeric waste to investigate performance of asphalt mixture Aggregates obtained from Margalla, Burhan and Karak quarries. 12 samples were prepared for conventional asphalt mixtures and 48 samples were prepared for PB modified asphalt mixture of each quarries at various proportions of PB waste. The PB used for modification according to wet process are 15%, 20%, 25% and 30% by weight of Optimum Bitumen Content (OBC. OBC of 4.2 % was concluded for conventional asphalt mixtures. The stability and flow values of the conventional and modified Asphalt Mixture were compared. The average Stability of the modified Margalla asphalt mixtures when 15% PB was used was much higher as compared to conventional asphalt mixtures. But when PB was used beyond 15%, the Marshall stability showed a decreasing trend for Margalla aggregates, increasing trend for Karak aggregates and decreasing trend for Burhan aggregates. This decline in stability is attributed to a decline in interlocking of aggregates due to lubricating effect. The corresponding flow for the Modified asphalt mixtures first showed a decreasing trend for Margalla aggregates at 15% PB modification but beyond 15%, an increasing trend in flow as compared to conventional asphalt mixtures The decrease in flow or increase in Marshall Stability is attributed to improvement in interlocking and decline in flow or stability is attributed to a decline in interlocking offered by binder and PB coated aggregate particles in modified asphalt.

  15. Initiation of explosive mixtures having multi-sized structures

    Science.gov (United States)

    Vasil'ev, A. A.; Vasiliev, V. A.; Trotsyuk, A. V.

    2016-10-01

    Theory of strong blast was used as the basis for the experimental method of determining of the energy of source which provides the initiation of combustible mixture. For mono-fuel mixtures the following parameters were experimentally determined at testing: the critical initiation energy of a cylindrical detonation wave in mixtures 2H2+O2 and C2H2+2.5O2 (exploding wire); the critical initiation energy of a spherical detonation in a mixture of C2H2+2.5O2 (electrical discharge). Similarly, for the double-fuel mixtures of acetylene - nitrous oxide - oxygen (having bifurcation cellular structures) the critical initiation energy of spherical wave was determined also. It was found that for the stoichiometric mixture on both fuel components the critical energy of mixture with the bifurcation structure was undervalued by several times in comparison with the value of the critical energy for the mono-fuel mixture, in which the cell size at a given pressure is determined by the large scale of bifurcation cells. This result shows the decrease of the critical energy with an increase of the number of "hot spots", which are the numerous areas of collision of the transverse waves of large and small scales in a mixture with bifurcation properties.

  16. Heat transfer from a high temperature condensable mixture

    International Nuclear Information System (INIS)

    Chan, S.H.; Cho, D.H.; Condiff, D.W.

    1980-01-01

    Bulk condensation and heat transfer in a very hot gaseous mixture that contains a vapor component condensable at high temperature are investigated. A general formulation of the problem is presented in various forms. Analytical solutions for three specific cases involving both one- and two-component two-phase mixtures are obtained. It is shown that a detached fog formation is induced by rapid radiative cooling from the mixture. The formation of radiatively induced fog is found to be an interesting and important phenomenon as it not only exhibits unique features different from the conventional diffusion induced fog, but also greatly enhances heat transfer from the mixture to the boundary. (author)

  17. Performance of an organic Rankine cycle with multicomponent mixtures

    International Nuclear Information System (INIS)

    Chaitanya Prasad, G.S.; Suresh Kumar, C.; Srinivasa Murthy, S.; Venkatarathnam, G.

    2015-01-01

    There is a renewed interest in ORC (organic Rankine cycle) systems for power generation using solar thermal energy. Many authors have studied the performance of ORC with different pure fluids as well as binary zeotropic mixtures in order to improve the thermal efficiency. It has not been well appreciated that zeotropic mixtures can also be used to reduce the size and cost of an ORC system. The main objective of this paper is to present mixtures that help reduce the cost while maintaining high thermal efficiency. The proposed method also allows us to design an optimum mixture for a given expander. This new approach is particularly beneficial for designing mixtures for small ORC systems operating with solar thermal energy. A number of examples are presented to demonstrate this concept. - Highlights: • The performance of an ORC operating with different zeotropic multicomponent mixtures is presented. • A thermodynamic method is proposed for the design of multicomponent mixtures for ORC power plants. • High exergy efficiency as well as high volumetric expander work can be achieved with appropriate mixtures. • The method allows design of mixtures that can be used with off-the-shelf positive displacement expanders

  18. Development of a slow mono-kinetic electron source; Etude et realisation d'une source d'electrons lents monocinetiques

    Energy Technology Data Exchange (ETDEWEB)

    Ballu, Y [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-06-01

    A comparative study of already existing slow mono-kinetic electron guns shows that those using a 127 degrees electrostatic selector can be improved still further to arrive at the performances obtained with spherical 180 degrees selectors for example. For this reason we have examined the 127 degrees selector theoretically in more detail; it appears that it should be possible to obtain a resolving power better than 30 mV for a current of about 10{sup -10} A, on condition that certain improvements be made to the instrument as normally designed, in particular concerning the entrance and exit slides. As a result, the usual suppressors for the scattered electrons are no longer necessary. The development of this apparatus has been carried out with particular care: the dimensional characteristics are fixed to an accuracy of a few microns, although the instrument can be baked out at 300 C. The experimental results are in excellent agreement with the theoretical predictions: for a current of 10{sup -10} A, the measured resolving power is 24 {+-} 4 mV. The easy detection of the He{sup -} resonance line at 19.3 eV has confirmed the advantages of this apparatus for the study of atomic collisions. (author) [French] L'etude comparative des canons a electrons lents monocinetiques realises jusqu'a present montre que ceux qui utilisent un selecteur electrostatique a 127 degres peuvent etre encore perfectionnes en vue de parvenir aux performances obtenues avec les selecteurs spheriques a 180 degres par exemple. D'ou notre etude theorique approfondie du selecteur a 127 degres qui nous a conduit a esperer une resolution meilleure que 30 mV pour un courant de l'ordre de 10{sup -10} A a condition d'apporter certaines ameliorations a la conception usuelle de cet instrument notamment au niveau des fentes d'entree et de sortie. Par voie de consequence les suppresseurs habituels d'electrons parasites deviennent inutiles. L'etude et la mise au point de l'appareil ont fait l'objet de soins

  19. Study of cerenkov radiation. Production of {gamma} rays by electron accelerators; Etude du rayonnement de freinage. Production de rayons {gamma} par des accelerateurs d'electrons

    Energy Technology Data Exchange (ETDEWEB)

    Bernard, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-07-01

    This study is a critical comparison of the theories of Bremsstrahlung. Experimental results obtained by the production of {gamma} radiation with electron accelerators are compared to the theoretical results in order to estimate the extent to which the various theories are valid. (author) [French] Cette etude est une synthese des theories du rayonnement de freinage. Des resultats experimentaux, obtenus par la production de rayonnements {gamma} avec des accelerateurs d'electrons, sont compares aux resultats theoriques afin d'evaluer les domaines de validite des diverses theories. (auteur)

  20. Use of hydraulic and aerial mock up to study atmospheric pollution; L'utilisation des maquettes aeriennes et hydrauliques pour l'etude de la pollution atmospherique

    Energy Technology Data Exchange (ETDEWEB)

    Facy, L; Perrin De Brichambaut, C; Doury, A; Le Quinio, R

    1962-07-01

    Fundamental studies on turbulent atmospheric diffusion of finely divided particles, cannot remain on a purely theoretical basis. Further experimental studies must be considered. - In full scale, from accidental and induced releases. - On a reduced scale, in aerodynamic wind tunnels or hydraulic water tunnels. A first set of studies on reduced scale models has been worked out according to a contract between French 'Meteorologie Nationale' and French 'Commissariat a l'Energie Atomique' and with the Collaboration of Saint-Cyr 'Institut Aerotechnique'. Essentially two kinds of results have been obtained: - The mathematical model of SUTTON for the turbulent diffusion in the atmosphere, deduced from the SUTTON theory, generally used by us, has been correctly verified, qualitatively and quantitatively whenever experiments were consistent with the theory conditions. - The quantitative assays of photographic and cinematographic visualization have given precise details on the phenomena inaccessible to calculations, due to the influence of obstacles and release conditions. - Generally, it can be asserted, that the atmospheric pollution studies are worked out by mock up experimentations and that, in some cases these experiments never can be replaced by mathematically pure models. (authors) [French] Les etudes fondamentales portant sur la diffusion turbulente dans l'atmosphere de quantites de matieres finement divisees, ne peuvent se maintenir sur un plan exclusivement theorique. C'est pourquoi des etudes experimentales complementaires doivent etre obligatoirement envisagees: - en vraie grandeur, a partir d'emissions accidentelles ou provoquees; - sur modeles reduits, en soufflerie aerodynamique ou en veine hydraulique. En ce qui concerne les modeles reduits, une premiere serie d'etudes a pu etre menee a bien, dans le cadre d'un contrat passe entre la Meteorologie Nationale et le Commissariat a l'Energie Atomique, et avec la collaboration de l'Institut Aerotechnique de Saint

  1. Studies of magnetism with inelastic scattering of cold neutrons; Etudes de magnetisme realisees a l'aide de la diffusion inelastique de neutrons froids

    Energy Technology Data Exchange (ETDEWEB)

    Jacrot, B [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    Inelastic scattering of cold neutrons can be used to study some aspects of magnetism: spins waves, exchange integrals, vicinity of Curie point. After description of the experimental set-up, several experiments, in the fields mentioned above, are analysed. (author) [French] La technique de diffusion inelastique des neutrons froids est utilisee pour etudier certains aspects du magnetisme: ondes de spins, integrales d'echange, etude au voisinage du point de Curie, etc. Apres une description de l'appareillage, on analyse diverses experiences effectuees dans les domaines enumeres plus haut. (auteur)

  2. Probes and their application to the study of H.F. plasmoids; Les sondes et leur application dans l'etude des plasmoides H.F

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, A; Geller, R [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    In the first part of this paper, we study the single Langmuir probe and the double-probe method. In the second part, we describe the probe-technique in connection with R.F. plasmoids. (author) [French] Dans la premiere partie de cet article, nous rappelons les principes d'utilisation de la sonde simple de Langmuir ainsi que la methode de la sonde double. La seconde partie est consacree a la pratique des sondes dans l'etude des plasmoides H.F. (auteur)

  3. Porous concrete mixtures for pervious urban pavements

    Directory of Open Access Journals (Sweden)

    Castro, J.

    2007-08-01

    Full Text Available The present study aimed to analyze the hydraulic and mechanical behaviour of a series of roller-compacted, laboratory porous concrete mixtures. The mix design variables examined were the actual void ratio in the hardened concrete and the water/cement ratio. From these results the better dosages from the mechanical and hydraulical behaviour point of view were determined. One of the designs developed was found to exhibit excellent hydraulic capacity and 20% greater strength than the mixtures recommended in the literature. Moreover, concrete with an actual void ratio of only 14% was observed to meet permeability requirements. Maximum flexural strength of concretes with different w/c ratios was achieved with a cement paste content of 250 l/m3. Relationships were found between the void ratio and both 28-day concrete permeability and flexural strength. Finally, the doses exhibiting the best mechanical and hydraulic performance were identified.El trabajo realizado en este estudio consistió en analizar el comportamiento de diferentes dosificaciones de mezclas de hormigón poroso, fabricadas en laboratorio y compactadas con rodillo pesado para simular las condiciones de terreno. Las variables consideradas para el diseño de las mezclas fueron el porcentaje real de huecos en el hormigón endurecido y la razón agua/cemento. A partir de estos resultados se determinaron las dosificaciones que presentan mejor comportamiento desde el punto de vista mecánico e hidráulico. Los resultados muestran que existe una dosificación de hormigón poroso, distinta a las encontradas actualmente en la literatura internacional, que permite obtener resistencias hasta 20% más altas, manteniendo todavía una excelente capacidad hidráulica. Se determinó que una permeabilidad suficiente se puede obtener con un porcentaje real de huecos de 14%, y que agregar pasta de cemento en una proporción de 250 l/m3 permite maximizar la resistencia a flexotracción de hormigones que

  4. Method of research and study of uranium deposits; Methode de recherches et d'etude des gites uraniferes

    Energy Technology Data Exchange (ETDEWEB)

    Lenoble, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1955-07-01

    In a first part, the author gives a fast retrospective of the evaluations of the uranium deposits in the French Union. The author established a method of prospecting and studying, modifiable at all times following the experiences and the results, permitting to make the general inventory of uranium resources on the territory. The method is based on: 1 - the determination of geological guides in order to mark the most promising deposits, 2 - the definition of a methodology adapted to every steps of the research, 3 - the choice of the material adapted for each of the steps. This method, originally established for the prospecting in crystalline massifs, is adaptable to the prospecting of the sedimentary formations. (M.B.) [French] Dans une premiere partie, l'auteur donne une retrospective rapide des estimations des gites uraniferes dans l'Union Francaise. L'auteur a etabli une methode de prospection et d'etude, modifiable a tout instant suivant les experiences et les resultats, permettant de faire l'inventaire general des ressources en uranium du territoire. La methode est base sur: 1 - la determination de guides geologiques afin de reperer les gisements les plus prometteurs, 2 - la definition d'une methodologie adaptee a chaque stade de la recherche, 3 - le choix du materiel adapte pour chacun des stades. Cette methode, a l'origine etablie pour la prospection en massifs cristallins, est adaptable a la prospection des formations sedimentaires. (M.B.)

  5. Some equipment for graphite research in swimming pool reactors; Quelques dispositifs d'etude du graphite dans les piles piscines

    Energy Technology Data Exchange (ETDEWEB)

    Seguin, M; Arragon, Ph; Dupont, G; Gentil, J; Tanis, G [Commissariat a l' Energie Atomique, Grenoble (France). Centre d' Etudes Nucleaires

    1964-07-01

    The irradiation devices described are used for research concerning reactors of the natural uranium type, moderated by graphite and cooled by carbon dioxide. The devices are generally designed for use in swimming pool reactors. The following points have been particularly studied: - maximum use of the irradiation volume, - use of the simplest technological solutions, - standardization of certain constituent parts. This standardization calls for precision machining and careful assembling; these requirements are also true when a relatively low irradiation temperature is required and the nuclear heating is pronounced. Finally, the design of these devices is suitable for the irradiation of other fissile or non-fissile materials. (authors) [French] Les dispositifs d'irradiation decrits servent aux etudes relatives a la filiere des reacteurs a uranium naturel, moderes au graphite et refroidis par le gaz carbonique. Ils sont generalement concus pour etre utilises dans des piles piscines. L'accent a ete mis sur: - l'utilisation au maximum du volume d'irradiation, - le recours aux solutions technologiques les plus simples, - la standardisation de certaines parties constitutives. Cette standardisation impose un usinage precis et un montage soigne, lesquels sont egalement necessaires lorsqu'on doit obtenir une temperature d'irradiation relativement basse alors que l'echauffement nucleaire est important. Enfin, la conception de ces dispositifs est valable pour irradier d'autres materiaux non fissiles ou fissiles. (auteurs)

  6. Serotonin transporter gene polymorphism and myocardial infarction: Etude Cas-Témoins de l'Infarctus du Myocarde (ECTIM).

    Science.gov (United States)

    Fumeron, Frédéric; Betoulle, Dina; Nicaud, Viviane; Evans, Alun; Kee, Frank; Ruidavets, Jean-Bernard; Arveiler, Dominique; Luc, Gérald; Cambien, François

    2002-06-25

    Depression is a risk factor for myocardial infarction (MI). Selective serotonin reuptake inhibitors reduce this risk. The site of action is the serotonin transporter (SLC6A4), which is expressed in brain and blood cells. A functional polymorphism in the promoter region of the SLC6A4 gene has been described. This polymorphism may be associated with the risk of MI. The SLC6A4 polymorphism has been investigated by polymerase chain reaction in 671 male patients with MI and in 688 controls from the Etude Cas-Témoins de l'Infarctus du Myocarde (ECTIM) multicentric study. Percentages for LL, LS, and SS genotypes were 35.5%, 45.4%, and 19.1%, respectively, for cases versus 28.1%, 49.1%, and 22.8%, respectively, for controls. S allele frequency was 41.8% and 47.4% for cases and controls, respectively. After adjustment for age and center by using multivariable logistic regression, the odds ratio for MI associated with the LL genotype was 1.40 (95% CI 1.11 to 1.76, P=0.0047). The LL genotype of the SLC6A4 polymorphism is associated with a higher risk of MI. This could be attributable to the effect of the polymorphism on serotonin-mediated platelet activation or smooth muscle cell proliferation or on other risk factors, such as depression or response to stress.

  7. Cognitive decline is associated with systemic oxidative stress: the EVA study. Etude du Vieillissement Artériel.

    Science.gov (United States)

    Berr, C; Balansard, B; Arnaud, J; Roussel, A M; Alpérovitch, A

    2000-10-01

    To determine whether systemic oxidative stress status is associated with cognitive decline. A longitudinal population-based study. A cohort study of older subjects in Nantes, France. A total of 1166 high cognitive functioning subjects aged 60 to 70 in the Etude du Vieillissement Arteriel (EVA) cohort with a 4 year follow-up. Subjects completed a baseline interview and a global cognitive test (Mini-Mental Status Examination (MMSE)). Blood samples were obtained at baseline to determine plasma levels of selenium, carotenoids, thiobarbituric acid reactant substances (TBARS), an indicator of lipoperoxidation, and red blood cell vitamin E. Risk of cognitive decline, defined as a loss of 3 points in MMSE score between baseline and the 4 year follow-up, was assessed by oxidative stress level. Subjects with the highest levels of TBARS show an increased risk of cognitive decline (adjusted odds ratio (OR) = 2.25; confidence interval (CI) 95% = 1.26-4.02). This result is reinforced in the lower antioxidant status subgroup. Subjects with low levels of selenium have an increased risk of cognitive decline (OR = 1.58; CI 95% = 1.08-2.31) after adjustment for various confounding factors. These results suggest that increased levels of oxidative stress and/or antioxidant deficiencies may pose risk factors for cognitive decline. The direct implication of oxidative stress in vascular and neurodegenerative mechanisms that lead to cognitive impairment should be further explored.

  8. Some aspects of nuclear graphite production in France; Etude generale sur les graphites nucleaires produits en France

    Energy Technology Data Exchange (ETDEWEB)

    Gueron, J; Hering, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Legendre, A [Pechiney, 75 - Paris (France)

    1958-07-01

    1) Manufacturing: A summary and results on the CEA-Pechiney purification process are given. Variations in the preparation of green pastes and their effects on graphitized material are described. 2) Physical and mechanical properties: Results are given on: - Statistics of dimensional variatior products having square cross-section. - Statistical variation of thermal expansion coefficients and of electrical conductivity. - Density of normals to carbon layer planes and their connexion with thermal expansion. - Stress-strain cycles and conclusions drawn therefrom. - Mechanical resistance and gas permeability of items for supporting fuel elements. 3) Behaviour under radiation: Alteration under radiation of French graphites irradiated either in G1 pile or in experimental piles, and thermal annealing of those alterations, are given. (author)Fren. [French] 1) Fabrication: On resume le procede d'epuration CEA-PECHINEY, ainsi que diverses modalites de preparation des pates et on expose les resultats obtenus. 2) Proprietes physiques et mecaniques: On indique le resultat d'etudes sur: - la statistique des dimensions de produits a section carree. - celle des variations des coefficients de dilatation thermique et de la conductibilite electrique. - la densite des normales aux plans graphitiques et leur connexion avec la dilatation thermique. - la compression mecanique du graphite. - la solidite mecanique et la permeabilite aux gaz de pieces destinees a supporter des cartouches de combustible. 3) Tenue sous rayonnement: Modification sous rayonnement des graphites fran is irradies soit dans la pile G1, soit dans des piles experimentales, et guerison thermique de ces modifications. (auteur)

  9. Compendium of shock wave data. Section C. Organic compounds excluding hydrocarbons. Section D. Mixtures. Section E. Mixtures and solutions without chemical characterization. Compendium index

    International Nuclear Information System (INIS)

    van Thiel, M.; shaner, J.; Salinas, E.

    1977-06-01

    This volume lists thermodynamic data for organic compounds excluding hydrocarbons, mixtures, and mixtures and solutions without chemical characterization. Alloys and some minerals are included among the mixtures. This volume also contains the index for the three-volume compendium

  10. Etude des phenomenes dynamiques ultrarapides et des caracteristiques impulsionnelles d'emission terahertz du supraconducteur YBCO

    Science.gov (United States)

    Savard, Stephane

    Les premieres etudes d'antennes a base de supraconducteurs a haute temperature critique emettant une impulsion electromagnetique dont le contenu en frequence se situe dans le domaine terahertz remontent a 1996. Une antenne supraconductrice est formee d'un micro-pont d'une couche mince supraconductrice sur lequel un courant continu est applique. Un faisceau laser dans le visible est focalise sur le micro-pont et place le supraconducteur dans un etat hors-equilibre ou des paires sont brisees. Grace a la relaxation des quasiparticules en surplus et eventuellement de la reformation des paires supraconductrices, nous pouvons etudier la nature de la supraconductivite. L'analyse de la cinetique temporelle du champ electromagnetique emis par une telle antenne terahertz supraconductrice s'est averee utile pour decrire qualitativement les caracteristiques de celle-ci en fonction des parametres d'operation tels que le courant applique, la temperature et la puissance d'excitation. La comprehension de l'etat hors-equilibre est la cle pour comprendre le fonctionnement des antennes terahertz supraconductrices a haute temperature critique. Dans le but de comprendre ultimement cet etat hors-equilibre, nous avions besoin d'une methode et d'un modele pour extraire de facon plus systematique les proprietes intrinseques du materiau qui compose l'antenne terahertz a partir des caracteristiques d'emission de celle-ci. Nous avons developpe une procedure pour calibrer le spectrometre dans le domaine temporel en utilisant des antennes terahertz de GaAs bombarde aux protons H+ comme emetteur et detecteur. Une fois le montage calibre, nous y avons insere une antenne emettrice dipolaire de YBa 2Cu3O7-delta . Un modele avec des fonctions exponentielles de montee et de descente du signal est utilise pour lisser le spectre du champ electromagnetique de l'antenne de YBa 2Cu3O7-delta, ce qui nous permet d'extraire les proprietes intrinseques de ce dernier. Pour confirmer la validite du modele

  11. Studies of the Stabilization of Superconductor Coils; Etudes sur la Stabilisation des Bobines Supraconductrices

    Energy Technology Data Exchange (ETDEWEB)

    Donadieu, L.; Maldy, J. [Compagnie Generale d' Electricite Marcoussis (France)

    1966-12-15

    operation of the coil will be stable and the passage of the I-B characteristic of the material will be reversible; (b) Ic < Im, the operation of the coil is unstable and any sufficiently large disturbances (flux jump, movement of windings, etc. ) can produce blocking. This is inevitably the case with the large coils whose operational limit tends towards Im. Different coils have been constructed with more or leas stabilised materials and the results of tests on them are analysed as a' function of the previous theories. There Is a full discussion of the advantages and disadvantages of coil stabilizations. (author) [French] La stabilisation de l'intensite du courant dans les bobinages supra-conducteurs, qui apparait d'une importance capitale pour la construction de bobinages de grande taille , est etudiee a la fois du point de vue theorique et du point de vue experiment a l. L'etude de la dynamique de la transition d'un supraconducteur transportant du courant, entre l ' e t at supraconducteur a resistance nulle et l ' e tat a resistance normale ( l e blocage), revele l'existence d'une intensite caracteristique, Im, pour laquelle la vitesse de propagation de la region normale est nulle. Cette intensite depend directement des echanges de chaleur entre le supraconducteur et le milieu ambiant, et de la resistance du materiau a l ' e t a t normal; Im depend indirectement de l'intensite du champ magnetique. Si un supraconducteur est utilise avec une intensite de courant inferieure a Im, la vitesse de propagation est negative et le supraconducteur est capable eventuellement de realiser la transition inverse de l ' e t a t normal a l ' e t a t supraconducteur. On peut montrer que pour une intensite Is telle que Is = Im/ Square-Root 2 , la vitesse de propagation qui est negative devient infiniment grande. L'existence de ces 2 intensites caracteristiques permet de distinguer trois cas de comportement differents selon l'intensite du courant qui parcourt le supraconducteur. L'auteur a

  12. Electrochemical study in molten potassium thiocyanate; Etude electrochimique dans le thiocyanate de potassium fondu

    Energy Technology Data Exchange (ETDEWEB)

    Metzger, G [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1964-07-01

    comparaison des valeurs des potentiels trouves dans le thiocyanate avec celles qui sont connues pour d'autres solvants fondus, nous a permis de rapprocher les proprietes du thiocyanate de celles de certains sels comme les chlorures ou les nitrates fondus. Ainsi les proprietes complexantes de SCN{sup -} vis-a-vis de Cu{sup +} exaltent les proprietes oxydantes de Cu{sup 2+}. Une etude polarographique de complexes dans le bain fondu, nous a revele l'existence de deux complexes cupro-cyanures de formules Cu(CN){sup -}{sub 2} et Cu(CN){sup 3-}{sub 4}, dont nous avons determine, experimentalement les constantes de dissociation. (auteur)

  13. Study of uranium-titanium diffusion; Etude de la diffusion uranium-titane

    Energy Technology Data Exchange (ETDEWEB)

    Adda, Y; Philibert, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires; Institut de Recherches de la Siderurgie Francaise (IRSID), 78 - Saint-Germain-en-Laye (France)

    1959-07-01

    . (author) [French] Dans le cadre de recherches sur la diffusion chimique de l'uranium et des metaux de transition, nous avons etudie le systeme uranium-titane. Les couples de diffusion sont prepares, suivant une technique que avons deja decrite, par soudage sous pression de plaquettes d'uranium et de titane. Apres traitement de diffusion sous vide, les echantillons sont etudies micrographiquement suivant une section polie. Cet examen nous a permis de mettre en evidence une diffusion intergranulaire au-dessous de 650 deg. C; aux temperatures superieures, la diffusion a lieu uniquement en volume, et la zone de diffusion apparait alors comme une succession de bandes qui se distinguent par leur aspect micrographique. L'etude de la cinetique de croissance de ces bandes nous a permis de mesurer les 'coefficients de penetration' correspondants. En outre, nous avons observe, dans la zone de diffusion, des variations importantes de microdurete, que nous avons cherche a relier a la variation de concentration. Celle-ci est mesuree par analyse ponctuelle au moyen de la microsonde de Castaing. Nous avons ainsi etabli avec precision les courbes concentration-penetration pour des temperatures comprises entre 950 et 1075 deg. C. A partir de ces courbes nous avons calcule le coefficient de diffusion D en fonction de la concentration c par la methode de Matano. La coube D(c) presente a toutes les temperatures une forme en U, deja observee pour le systeme U-Zr. L'energie d'activation passe par un maximum de 42 kcal/g pour une concentration atomique 0,5. Bien que nous n'ayons observe que rarement la presence de pores dans la zone de diffusion, nous avons neanmoins observe un effet Kirkendall important en etudiant les deplacements x{sub i} d'un interface repere au moyen de fils de tungstene. Ces deplacements peuvent s'exprimer en fonction du temps t et de la temperature T par la relation x{sub i} = 0,9 t {sup 1/2} exp ( - 14600/(RT)). Enfin, au moyen des equations de Darken nous avons calcule

  14. Structure of colloidal sphere-plate mixtures

    International Nuclear Information System (INIS)

    Doshi, N; Cinacchi, G; Van Duijneveldt, J S; Cosgrove, T; Prescott, S W; Grillo, I; Phipps, J; Gittins, D I

    2011-01-01

    In addition to containing spherical pigment particles, coatings usually contain plate-like clay particles. It is thought that these improve the opacity of the paint film by providing an efficient spacing of the pigment particles. This observation is counterintuitive, as suspensions of particles of different shapes and sizes tend to phase separate on increase of concentration. In order to clarify this matter a model colloidal system is studied here, with a sphere-plate diameter ratio similar to that found in paints. For dilute suspensions, small angle neutron scattering revealed that the addition of plates leads to enhanced density fluctuations of the spheres, in agreement with new theoretical predictions. On increasing the total colloid concentration the plates and spheres phase separate due to the disparity in their shape. This is in agreement with previous theoretical and experimental work on colloidal sphere-plate mixtures, where one particle acts as a depleting agent. The fact that no large scale phase separation is observed in coatings is ascribed to dynamic arrest in intimately mixed, or possibly micro-phase separated structures, at elevated concentration.

  15. Structure of colloidal sphere-plate mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Doshi, N; Cinacchi, G; Van Duijneveldt, J S; Cosgrove, T; Prescott, S W [School of Chemistry, University of Bristol, Bristol BS8 1TS (United Kingdom); Grillo, I [Institut Laue-Langevin, 6 rue Jules Horowitz BP 156, 38042 Grenoble Cedex 9 (France); Phipps, J [Imerys Minerals Ltd, Par Moor Centre, Par Moor Road, Par, Cornwall PL24 2SQ (United Kingdom); Gittins, D I, E-mail: Giorgio.Cinacchi@bristol.ac.uk, E-mail: J.S.van-Duijneveldt@bristol.ac.uk [Imerys Performance and Filtration Minerals Ltd, 130 Castilian Drive, Goleta, CA 93117 (United States)

    2011-05-18

    In addition to containing spherical pigment particles, coatings usually contain plate-like clay particles. It is thought that these improve the opacity of the paint film by providing an efficient spacing of the pigment particles. This observation is counterintuitive, as suspensions of particles of different shapes and sizes tend to phase separate on increase of concentration. In order to clarify this matter a model colloidal system is studied here, with a sphere-plate diameter ratio similar to that found in paints. For dilute suspensions, small angle neutron scattering revealed that the addition of plates leads to enhanced density fluctuations of the spheres, in agreement with new theoretical predictions. On increasing the total colloid concentration the plates and spheres phase separate due to the disparity in their shape. This is in agreement with previous theoretical and experimental work on colloidal sphere-plate mixtures, where one particle acts as a depleting agent. The fact that no large scale phase separation is observed in coatings is ascribed to dynamic arrest in intimately mixed, or possibly micro-phase separated structures, at elevated concentration.

  16. Hydrodynamic 'memory' of binary fluid mixtures

    International Nuclear Information System (INIS)

    Kalashnik, M. V.; Ingel, L. Kh.

    2006-01-01

    A theoretical analysis is presented of hydrostatic adjustment in a two-component fluid system, such as seawater stratified with respect to temperature and salinity. Both linear approximation and nonlinear problem are investigated. It is shown that scenarios of relaxation to a hydrostatically balanced state in binary fluid mixtures may substantially differ from hydrostatic adjustment in fluids that can be stratified only with respect to temperature. In particular, inviscid two-component fluids have 'memory': a horizontally nonuniform disturbance in the initial temperature or salinity distribution does not vanish even at the final stage, transforming into a persistent thermohaline 'trace.' Despite stability of density stratification and convective stability of the fluid system by all known criteria, an initial temperature disturbance may not decay and may even increase in amplitude. Moreover, its sign may change (depending on the relative contributions of temperature and salinity to stable background density stratification). Hydrostatic adjustment may involve development of discontinuous distributions from smooth initial temperature or concentration distributions. These properties of two-component fluids explain, in particular, the occurrence of persistent horizontally or vertically nonuniform temperature and salinity distributions in the ocean, including discontinuous ones

  17. Nonparametric Mixture Models for Supervised Image Parcellation.

    Science.gov (United States)

    Sabuncu, Mert R; Yeo, B T Thomas; Van Leemput, Koen; Fischl, Bruce; Golland, Polina

    2009-09-01

    We present a nonparametric, probabilistic mixture model for the supervised parcellation of images. The proposed model yields segmentation algorithms conceptually similar to the recently developed label fusion methods, which register a new image with each training image separately. Segmentation is achieved via the fusion of transferred manual labels. We show that in our framework various settings of a model parameter yield algorithms that use image intensity information differently in determining the weight of a training subject during fusion. One particular setting computes a single, global weight per training subject, whereas another setting uses locally varying weights when fusing the training data. The proposed nonparametric parcellation approach capitalizes on recently developed fast and robust pairwise image alignment tools. The use of multiple registrations allows the algorithm to be robust to occasional registration failures. We report experiments on 39 volumetric brain MRI scans with expert manual labels for the white matter, cerebral cortex, ventricles and subcortical structures. The results demonstrate that the proposed nonparametric segmentation framework yields significantly better segmentation than state-of-the-art algorithms.

  18. Complex contaminant mixtures in multistressor Appalachian riverscapes.

    Science.gov (United States)

    Merriam, Eric R; Petty, J Todd; Strager, Michael P; Maxwell, Aaron E; Ziemkiewicz, Paul F

    2015-11-01

    Runoff from watersheds altered by mountaintop mining in the Appalachian region (USA) is known to pollute headwater streams, yet regional-scale assessments of water quality have focused on salinization and selenium. The authors conducted a comprehensive survey of inorganic contaminants found in 170 stream segments distributed across a spectrum of historic and contemporary human land use. Principal component analysis identified 3 important dimensions of variation in water chemistry that were significantly correlated with contemporary surface mining (principal component 1: elevated dominant ions, sulfate, alkalinity, and selenium), coal geology and legacy mines (principal component 2: elevated trace metals), and residential development (principal component 3: elevated sodium and chloride). The combination of these 3 dominant sources of pollutants produced a complex stream-to-stream patchwork of contaminant mixtures. Seventy-five percent of headwater streams (catchments  5 km(2) ) were classified as having reference chemistries, and chemistries indicative of combined mining and development contaminants accounted for 47% of larger streams (compared with 26% of headwater streams). Extreme degradation of larger streams can be attributed to accumulation of contaminants from multiple human land use activities that include contemporary mountaintop mining, underground mining, abandoned mines, and untreated domestic wastewater. Consequently, water quality improvements in this region will require a multicontaminant remediation approach. © 2015 SETAC.

  19. Mechanistic and Economical Characteristics of Asphalt Rubber Mixtures

    Directory of Open Access Journals (Sweden)

    Mena I. Souliman

    2016-01-01

    Full Text Available Load associated fatigue cracking is one of the major distress types occurring in flexible pavement systems. Flexural bending beam fatigue laboratory test has been used for several decades and is considered to be an integral part of the new superpave advanced characterization procedure. One of the most significant solutions to prolong the fatigue life for an asphaltic mixture is to utilize flexible materials as rubber. A laboratory testing program was performed on a conventional and Asphalt Rubber- (AR- gap-graded mixtures to investigate the impact of added rubber on the mechanical, mechanistic, and economical attributes of asphaltic mixtures. Strain controlled fatigue tests were conducted according to American Association of State Highway and Transportation Officials (AASHTO procedures. The results from the beam fatigue tests indicated that the AR-gap-graded mixtures would have much longer fatigue life compared with the reference (conventional mixtures. In addition, a mechanistic analysis using 3D-Move software coupled with a cost analysis study based on the fatigue performance on the two mixtures was performed. Overall, analysis showed that AR modified asphalt mixtures exhibited significantly lower cost of pavement per 1000 cycles of fatigue life per mile compared to conventional HMA mixture.

  20. Radiation-polymerizable mixture and recording material containing it

    International Nuclear Information System (INIS)

    Gersdorf, J.; Kleiner, H-J.

    1991-01-01

    Esters of dihydric alcohols with alkenylphosphonic or alkenylphosphinic acids which are polymerizable by free radicals are described. They are combined with polymer binders, in particular water-soluble polymers, and photoinitiators forming free radicals to give photopolymerizable mixtures which are suitable for the production of photoresists and printing plates. The mixtures display low heat-sensitivity and have long shelf lives. (author) 1 tab

  1. Ultrasonic study of molecular interaction in binary liquid mixtures at ...

    Indian Academy of Sciences (India)

    The variation of these parameters with composition of the mixture helps us in understanding the nature and extent of interaction between unlike molecules in the mixtures. Further, theoretical values of ultrasonic speed were evaluated using theories and empirical relations. The relative merits of these theories and relations ...

  2. Polymer mixtures in confined geometries: Model systems to explore ...

    Indian Academy of Sciences (India)

    to mean field behavior for very long chains, the critical behavior of mixtures confined into thin film geometry falls in the 2d Ising class irrespective of chain length. ..... AB interface does not approach the wall; (b) corresponds to a temperature .... Very recently, these theoretical studies have been extended to polymer mixtures.

  3. Self-consistent calculation of atomic structure for mixture

    International Nuclear Information System (INIS)

    Meng Xujun; Bai Yun; Sun Yongsheng; Zhang Jinglin; Zong Xiaoping

    2000-01-01

    Based on relativistic Hartree-Fock-Slater self-consistent average atomic model, atomic structure for mixture is studied by summing up component volumes in mixture. Algorithmic procedure for solving both the group of Thomas-Fermi equations and the self-consistent atomic structure is presented in detail, and, some numerical results are discussed

  4. Kinetic-sound propagation in dilute gas mixtures

    International Nuclear Information System (INIS)

    Campa, A.; Cohen, E.G.D.

    1989-01-01

    Kinetic sound is predicted in dilute disparate-mass binary gas mixtures, propagating exclusively in the light compound and much faster than ordinary sound. It should be detectable by light-scattering experiments, as an extended shoulder in the scattering cross section for large frequencies. As an example, H 2 -Ar mixtures are discussed

  5. Modeling the effects of binary mixtures on survival in time.

    NARCIS (Netherlands)

    Baas, J.; van Houte, B.P.P.; van Gestel, C.A.M.; Kooijman, S.A.L.M.

    2007-01-01

    In general, effects of mixtures are difficult to describe, and most of the models in use are descriptive in nature and lack a strong mechanistic basis. The aim of this experiment was to develop a process-based model for the interpretation of mixture toxicity measurements, with effects of binary

  6. Separation of organic azeotropic mixtures by pervaporation. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Baker, R.W.

    1991-12-01

    Distillation is a commonly used separation technique in the petroleum refining and chemical processing industries. However, there are a number of potential separations involving azetropic and close-boiling organic mixtures that cannot be separated efficiently by distillation. Pervaporation is a membrane-based process that uses selective permeation through membranes to separate liquid mixtures. Because the separation process is not affected by the relative volatility of the mixture components being separated, pervaporation can be used to separate azetropes and close-boiling mixtures. Our results showed that pervaporation membranes can be used to separate azeotropic mixtures efficiently, a result that is not achievable with simple distillation. The membranes were 5--10 times more permeable to one of the components of the mixture, concentrating it in the permeate stream. For example, the membrane was 10 times more permeable to ethanol than methyl ethyl ketone, producing 60% ethanol permeate from an azeotropic mixture of ethanol and methyl ethyl ketone containing 18% ethanol. For the ethyl acetate/water mixture, the membranes showed a very high selectivity to water (> 300) and the permeate was 50--100 times enriched in water relative to the feed. The membranes had permeate fluxes on the order of 0.1--1 kg/m{sup 2}{center_dot}h in the operating range of 55--70{degrees}C. Higher fluxes were obtained by increasing the operating temperature.

  7. Phase and viscosity behaviour of refrigerant-lubricant mixtures

    DEFF Research Database (Denmark)

    Cisneros, Sergio; Garcia, J.; Fernandez, J.

    2005-01-01

    , mainly as a function of the molecular asymmetry. This also has a profound effect in the mixture transport properties. Thus, in this work the general aspects of phase and viscosity behaviour linked to the type of asymmetry found in refrigerant-lubricant mixtures are discussed in the context of phase...

  8. Moisture sorption in mixtures of biopolymer, disaccharides and water

    NARCIS (Netherlands)

    Sman, van der R.G.M.

    2013-01-01

    The moisture sorption of ternary mixtures of biopolymer, sugar and water is investigated by means of the Free-Volume-Flory-Huggins (FVFH) theory. The earlier FVFH theory developed for binary mixtures of biopolymer/water and sugar/water has to be modified to account for two effects: 1) the change in

  9. Herbal mixtures in the traditional medicine of Eastern Cuba

    NARCIS (Netherlands)

    Hernández, J.; Volpato, G.

    2004-01-01

    Herbal mixtures in the traditional medicine of Eastern Cuba. Traditional herbal mixtures in Eastern Cuba are investigated through interviews with 130 knowledgeable people and traditional healers of the provinces of Santiago de Cuba and Guantanamo. One hundred seventy plant species and other products

  10. Kelvin Equation for a Non-Ideal Multicomponent Mixture

    DEFF Research Database (Denmark)

    Shapiro, Alexander; Stenby, Erling Halfdan

    1997-01-01

    The Kelvin equation is generalized by application to a case of a multicomponent non-ideal mixture. Such a generalization is necessary in order to describe the two-phase equilibrium in a capillary medium with respect to both normal and retrograde condensation. The equation obtained is applied...... to the equilibrium state of a hydrocarbon mixture ina gas-condensate reservoir....

  11. Finite Gaussian Mixture Approximations to Analytically Intractable Density Kernels

    DEFF Research Database (Denmark)

    Khorunzhina, Natalia; Richard, Jean-Francois

    The objective of the paper is that of constructing finite Gaussian mixture approximations to analytically intractable density kernels. The proposed method is adaptive in that terms are added one at the time and the mixture is fully re-optimized at each step using a distance measure that approxima...

  12. Quantitative measurement of mixtures by terahertz time–domain ...

    Indian Academy of Sciences (India)

    Administrator

    earth and space science, quality control of food and agricultural products and global environmental monitoring. In quantitative applications, terahertz technology has been widely used for studying dif- ferent kinds of mixtures, such as amino acids,. 8 ter- nary chemical mixtures,. 9 pharmaceuticals,. 10 racemic compounds. 11.

  13. PREDICTING EVAPORATION RATES AND TIMES FOR SPILLS OF CHEMICAL MIXTURES

    Science.gov (United States)

    Spreadsheet and short-cut methods have been developed for predicting evaporation rates and evaporation times for spills (and constrained baths) of chemical mixtures. Steady-state and time-varying predictions of evaporation rates can be made for six-component mixtures, includ...

  14. Electron thermalization in rare gases and their mixtures

    International Nuclear Information System (INIS)

    Bronic, I.K.; Kimura, M.

    1996-01-01

    The time evolution and temperature dependence of electron energy distribution functions (EDFs) are studied in pure rare gases (He, Ne, Ar, Kr, Xe) as well as in their mixtures by using solutions of the Boltzmann equation. A clear difference between the gases having the Ramsauer endash Townsend (RT) minimum in the momentum-transfer cross section, (RT gases: Ar, Kr, and Xe), and those without the RT minimum (non-RT gases: He and Ne) is pointed out. The influence of the position and the depth of the RT minimum on the EDF and time evolution is studied for three different initial electron energies. A formula proposed for describing thermalization time in a mixture is tested on (i) a non-RT endash non-RT gas mixture, (ii) a RT endash non-RT mixture and (iii) a RT endash RT gas mixture. The linear combination of the reciprocal thermalization times in gas mixture with the component concentrations as weighting factors is found to be valid for gases with a similar energy dependence of the momentum-transfer cross section, σ m , and also for all rare-gas binary mixtures if the initial electron energy is sufficiently below the RT minimum. Conspicuous deviations from the linear relationship are observed in mixtures of gases whose energy dependence of σ m (or the stopping cross section) are different, and theoretical rationales for these findings are provided. copyright 1996 American Institute of Physics

  15. DESIGNS FOR MIXTURE AND PROCESS VARIABLES APPLIED IN TABLET FORMULATIONS

    NARCIS (Netherlands)

    DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

    1993-01-01

    Although there are several methods for the construction of a design for process variables and mixture variables, there are not very many methods which are suitable to combine mixture and process variables in one design. Some of the methods which are feasible will be shown. These methods will be

  16. Evaluating Mixture Modeling for Clustering: Recommendations and Cautions

    Science.gov (United States)

    Steinley, Douglas; Brusco, Michael J.

    2011-01-01

    This article provides a large-scale investigation into several of the properties of mixture-model clustering techniques (also referred to as latent class cluster analysis, latent profile analysis, model-based clustering, probabilistic clustering, Bayesian classification, unsupervised learning, and finite mixture models; see Vermunt & Magdison,…

  17. Mixture distributions of wind speed in the UAE

    Science.gov (United States)

    Shin, J.; Ouarda, T.; Lee, T. S.

    2013-12-01

    Wind speed probability distribution is commonly used to estimate potential wind energy. The 2-parameter Weibull distribution has been most widely used to characterize the distribution of wind speed. However, it is unable to properly model wind speed regimes when wind speed distribution presents bimodal and kurtotic shapes. Several studies have concluded that the Weibull distribution should not be used for frequency analysis of wind speed without investigation of wind speed distribution. Due to these mixture distributional characteristics of wind speed data, the application of mixture distributions should be further investigated in the frequency analysis of wind speed. A number of studies have investigated the potential wind energy in different parts of the Arabian Peninsula. Mixture distributional characteristics of wind speed were detected from some of these studies. Nevertheless, mixture distributions have not been employed for wind speed modeling in the Arabian Peninsula. In order to improve our understanding of wind energy potential in Arabian Peninsula, mixture distributions should be tested for the frequency analysis of wind speed. The aim of the current study is to assess the suitability of mixture distributions for the frequency analysis of wind speed in the UAE. Hourly mean wind speed data at 10-m height from 7 stations were used in the current study. The Weibull and Kappa distributions were employed as representatives of the conventional non-mixture distributions. 10 mixture distributions are used and constructed by mixing four probability distributions such as Normal, Gamma, Weibull and Extreme value type-one (EV-1) distributions. Three parameter estimation methods such as Expectation Maximization algorithm, Least Squares method and Meta-Heuristic Maximum Likelihood (MHML) method were employed to estimate the parameters of the mixture distributions. In order to compare the goodness-of-fit of tested distributions and parameter estimation methods for

  18. Investigation of Asphalt Mixture Creep Behavior Using Thin Beam Specimens

    International Nuclear Information System (INIS)

    Zofka, Adam; Marasteanu, Mihai; Turos, Mugur

    2008-01-01

    The asphalt pavement layer consists of two or more lifts of compacted asphalt mixture; the top of the layer is also exposed to aging, a factor that significantly affects the mixture properties. The current testing specifications use rather thick specimens that cannot be used to investigate the gradual change in properties with pavement depth. This paper investigates the feasibility of using the 3-point bending test with thin asphalt mixture beams (127x12.7x6.35 mm) to determine the low-temperature creep compliance of the mixtures. Several theoretical and semi-empirical models, from the theory of composites, are reviewed and evaluated using numerical and experimental data. Preliminary results show that this method can be used for low-temperature mixture characterization but several crucial factors need further inspection and interpretation

  19. Criticality of mixtures of plutonium and high enriched uranium

    International Nuclear Information System (INIS)

    Grolleau, E.; Lein, M.; Leka, G.; Maidou, B.; Klenov, P.

    2003-01-01

    This paper presents a criticality evaluation of moderated homogeneous plutonium-uranium mixtures. The fissile media studied are homogeneous mixtures of plutonium and high enriched uranium in two chemical forms: aqueous mixtures of metal and mixtures of nitrate solutions. The enrichment of uranium considered are 93.2wt.% 235 U and 100wt.% 235 U. The 240 Pu content in plutonium varies from 0wt.% 240 Pu to 12wt.% 240 Pu. The critical parameters (radii and masses of a 20 cm water reflected sphere) are calculated with the French criticality safety package CRISTAL V0. The comparison of the calculated critical parameters as a function of the moderator-to-fuel atomic ratio shows significant ranges in which high enriched uranium systems, as well as plutonium-uranium mixtures, are more reactive than plutonium systems. (author)

  20. Innovative aspects of protein stability in ionic liquid mixtures.

    Science.gov (United States)

    Kumar, Awanish; Venkatesu, Pannuru

    2018-06-01

    Mixtures of ionic liquids (ILs) have attracted our attention because of their extraordinary performances in extraction technologies and in absorbing large amount of CO 2 gas. It has been observed that when two or more ILs are mixed in different proportions, a new solvent is obtained which is much better than that of each component of ILs from which the mixture is obtained. Within a mixture of ILs, several unidentified interactions occur among several ions which give rise to unique solvent properties to the mixture. Herein, in this review, we have highlighted the utilization of the advantageous properties of the IL mixtures in protein stability studies. This approach is exceptional and opens new directions to the use of ILs in biotechnology.