Carbon dioxide dissociation and buffering in chicken blood during development.

Science.gov (United States)

Tazawa, H; Piiper, J

1984-07-01

Carbon dioxide dissociation curves of oxygenated and deoxygenated bloods, the Haldane effect, the buffer value and other blood and true plasma buffering indices, O2 capacity and hematocrit were determined in bloods withdrawn from chicks before, during and after hatching and 8-month-old hens. Blood CO2 dissociation curves shifted upwards in the developing embryo till pipping, and moved downwards after pipping and hatching. In accordance with the position of the CO2 dissociation curves, the true plasma bicarbonate and red cell CO2 standardized to PCO2 = 40 torr changed. The Haldane factor at standard PCO2 increased from 0.12-0.13 on days 10-14 of incubation to 0.34 in young hens. The buffering power changed in parallel with O2 capacity and hematocrit, increasing steadily during incubation, dropping at hatching and then increasing again to the adult value. The observed changes in the CO2 dissociation curves and buffering variables during the development enable the chick to minimize the changes in the acid-base status and are favorable for coping with the increasing demand for CO2 transport and buffering of the developing bird.

CO2 sequestration: Storage capacity guideline needed

Science.gov (United States)

Frailey, S.M.; Finley, R.J.; Hickman, T.S.

2006-01-01

Petroleum reserves are classified for the assessment of available supplies by governmental agencies, management of business processes for achieving exploration and production efficiency, and documentation of the value of reserves and resources in financial statements. Up to the present however, the storage capacity determinations made by some organizations in the initial CO2 resource assessment are incorrect technically. New publications should thus cover differences in mineral adsorption of CO2 and dissolution of CO2 in various brine waters.

Visualization of Buffer Capacity with 3-D "Topo" Surfaces: Buffer Ridges, Equivalence Point Canyons and Dilution Ramps

Science.gov (United States)

Smith, Garon C.; Hossain, Md Mainul

2016-01-01

BufCap TOPOS is free software that generates 3-D topographical surfaces ("topos") for acid-base equilibrium studies. It portrays pH and buffer capacity behavior during titration and dilution procedures. Topo surfaces are created by plotting computed pH and buffer capacity values above a composition grid with volume of NaOH as the x axis…

ROBUST: The ROle of BUffering capacities in STabilising coastal lagoon ecosystems

NARCIS (Netherlands)

De Wit, R.; Stal, L.J.; Lomstein, B.A.; Herbert, R.A.; van Gemerden, H.; Viaroli, P.; Cecherelli, V.U.; Rodriguez-Valera, F.; Bartoli, M.; Giordani, G.; Azzoni, R.; Schaub, B.; Welsh, D.T.; Donnelly, A.; Cifuentes, A.; Anton, J.; Finster, K.; Nielsen, L.P.; Pedersen, A.G.U.; Neubauer, A.T.; Colangelo, M.A.; Heijs, S.K.

2001-01-01

"Buffer capacities" has been defined in ecology as a holistic concept (e.g., Integration of Ecosystem Theories: A Pattern, second ed. Kluwer, Dordrecht, 1997, 388pp), but we show that it can also be worked out in mechanistic studies. Our mechanistic approach highlights that "buffering capacities"

ROBUST : The ROle of BUffering capacities in STabilising coastal lagoon ecosystems

NARCIS (Netherlands)

de Wit, R; Stal, LJ; Lomstein, BA; Herbert, RA; van Gemerden, H; Viaroli, P; Cecherelli, VU; Rodriguez-Valera, F; Bartoli, M; Giordani, G; Azzoni, R; Schaub, B; Welsh, DT; Donnelly, A; Cifuentes, A; Anton, J; Finster, K; Nielsen, LB; Pedersen, AGU; Neubauer, AT; Colangelo, MA; Heijs, SK

2001-01-01

"Buffer capacities" has been defined in ecology as a holistic concept (e.g., Integration of Ecosystem Theories: A Pattern, second ed. Kluwer, Dordrecht, 1997, 388pp), but we show that it can also be worked out in mechanistic studies. Our mechanistic approach highlights that "buffering capacities"

Biochar contribution to soil pH buffer capacity

Science.gov (United States)

Tonutare, Tonu; Krebstein, Kadri; Utso, Maarius; Rodima, Ako; Kolli, Raimo; Shanskiy, Merrit

2014-05-01

Biochar as ecologically clean and stable form of carbon has complex of physical and chemical properties which make it a potentially powerful soil amendment (Mutezo, 2013). Therefore during the last decade the biochar application as soil amendment has been a matter for a great number of investigations. For the ecological viewpoint the trend of decreasing of soil organic matter in European agricultural land is a major problem. Society is faced with the task to find possibilities to stabilize or increase soil organic matter content in soil and quality. The availability of different functional groups (e.g. carboxylic, phenolic, acidic, alcoholic, amine, amide) allows soil organic matter to buffer over a wide range of soil pH values (Krull et al. 2004). Therefore the loss of soil organic matter also reduces cation exchange capacity resulting in lower nutrient retention (Kimetu et al. 2008). Biochar can retain elements in soil directly through the negative charge that develops on its surfaces, and this negative charge can buffer acidity in the soil. There are lack of investigations about the effect of biochar to soil pH buffering properties, The aim of our investigation was to investigate the changes in soil pH buffer capacity in a result of addition of carbonizated material to temperate region soils. In the experiment different kind of softwood biochars, activated carbon and different soil types with various organic matter and pH were used. The study soils were Albeluvisols, Leptosols, Cambisols, Regosols and Histosols . In the experiment the series of the soil: biochar mixtures with the biochar content 0 to 100% were used. The times of equiliberation between solid and liquid phase were from 1 to 168 hours. The suspension of soil: biochar mixtures was titrated with HCl solution. The titration curves were established and pH buffer capacities were calculated for the pH interval from 3.0 to 10.0. The results demonstrate the dependence of pH buffer capacity from soil type

Salivary buffer capacity, pH, and stimulated flow rate of crack cocaine users.

Science.gov (United States)

Woyceichoski, Iverson Ernani Cogo; Costa, Carlos Henrique; de Araújo, Cristiano Miranda; Brancher, João Armando; Resende, Luciane Grochocki; Vieira, Iran; de Lima, Antonio Adilson Soares

2013-08-01

Crack cocaine is the freebase form of cocaine that can be smoked. The use of this drug has been considered a public health problem in many countries. The aim of this study was to assess the stimulated salivary flow rate (SSFR), pH, and the buffer capacity of saliva in crack cocaine users. Stimulated whole saliva was collected from 54 selected crack cocaine users and 40 non-users. All samples were analyzed for SSFR, pH, and buffer capacity. SSFR was analyzed by gravimetric method. The buffer capacity and pH were determined using a digital pH meter. The crack cocaine users demonstrated higher buffer capacity than the control group (P > 0.05). Salivary pH was lower in crack cocaine users (P 0.05). Crack cocaine users might exhibit a significant decrease in salivary pH, but not in salivary flow rate or buffer capacity. © 2012 Blackwell Publishing Asia Pty Ltd.

Designing Si/porous-C composite with buffering voids as high capacity anode for lithium-ion batteries

International Nuclear Information System (INIS)

Yue, Lu; Zhang, Wenhui; Yang, Jingfeng; Zhang, Lingzhi

2014-01-01

A novel Si/porous-C composite with buffering voids was prepared by the co-assembly of phenol-formaldehyde resin, SiO 2 and Si nanoparticles, followed by a carbonizing process and subsequent removal of SiO 2 template. Si nanoparticle was coated with a layer of porous carbon shell with rationally designed void in between which provides the accommodating space for the volume change of Si over cycling. The as-prepared composite electrode exhibited good electrochemical performances as an anode material in lithium-ion cells, showing a stable reversible capacity of 980 mAh g −1 over 80 cycles with small capacity fade of 0.17%/cycle and high rate capability (721 mAh g −1 at 2000 mA g −1 )

Buffer layer dependence of magnetoresistance effects in Co2Fe0.4Mn0.6Si/MgO/Co50Fe50 tunnel junctions

Science.gov (United States)

Sun, Mingling; Kubota, Takahide; Takahashi, Shigeki; Kawato, Yoshiaki; Sonobe, Yoshiaki; Takanashi, Koki

2018-05-01

Buffer layer dependence of tunnel magnetoresistance (TMR) effects was investigated in Co2Fe0.4Mn0.6Si (CFMS)/MgO/Co50Fe50 magnetic tunnel junctions (MTJs). Pd, Ru and Cr were selected for the buffer layer materials, and MTJs with three different CFMS thicknesses (30, 5, and 0.8 nm) were fabricated. A maximum TMR ratio of 136% was observed in the Ru buffer layer sample with a 30-nm-thick CFMS layer. TMR ratios drastically degraded for the CFMS thickness of 0.8 nm, and the values were 26% for Cr buffer layer and less than 1% for Pd and Ru buffer layers. From the annealing temperature dependence of the TMR ratios, amounts of interdiffusion and effects from the lattice mismatch were discussed.

Classification of CO2 Geologic Storage: Resource and Capacity

Science.gov (United States)

Frailey, S.M.; Finley, R.J.

2009-01-01

The use of the term capacity to describe possible geologic storage implies a realistic or likely volume of CO2 to be sequestered. Poor data quantity and quality may lead to very high uncertainty in the storage estimate. Use of the term "storage resource" alleviates the implied certainty of the term "storage capacity". This is especially important to non- scientists (e.g. policy makers) because "capacity" is commonly used to describe the very specific and more certain quantities such as volume of a gas tank or a hotel's overnight guest limit. Resource is a term used in the classification of oil and gas accumulations to infer lesser certainty in the commercial production of oil and gas. Likewise for CO2 sequestration, a suspected porous and permeable zone can be classified as a resource, but capacity can only be estimated after a well is drilled into the formation and a relatively higher degree of economic and regulatory certainty is established. Storage capacity estimates are lower risk or higher certainty compared to storage resource estimates. In the oil and gas industry, prospective resource and contingent resource are used for estimates with less data and certainty. Oil and gas reserves are classified as Proved and Unproved, and by analogy, capacity can be classified similarly. The highest degree of certainty for an oil or gas accumulation is Proved, Developed Producing (PDP) Reserves. For CO2 sequestration this could be Proved Developed Injecting (PDI) Capacity. A geologic sequestration storage classification system is developed by analogy to that used by the oil and gas industry. When a CO2 sequestration industry emerges, storage resource and capacity estimates will be considered a company asset and consequently regulated by the Securities and Exchange Commission. Additionally, storage accounting and auditing protocols will be required to confirm projected storage estimates and assignment of credits from actual injection. An example illustrates the use of

Evaluation of in situ sulfate reduction as redox buffer capacity in groundwater flow path

International Nuclear Information System (INIS)

Ioka, Seiichiro; Iwatsuki, Teruki; Amano, Yuki; Furue, Ryoji

2007-01-01

For safety assessment of geological isolation, it is important to evaluate in situ redox buffer capacity in high-permeability zone as groundwater flow path. The study evaluated in situ sulfate reduction as redox buffer capacity in the conglomerate bedding in Toki Lignite-bearing Formation, which occurs at the lowest part of sedimentary rocks overlying basement granite. The bedding plays an important role as the main groundwater flow path. The result showed that in situ redox buffer capacity in the conglomerate bedding has been identified on first nine months, whereas in the following period the redox buffer capacity has not been identified for about fifteen months. This will be caused by the bedding became inappropriate for microbial survival as the organic matter which is needfuel for microbial activity was consumed. Thus, there will be limited redox buffer capacity in groundwater flow path even in formation including organic matter-bearing layer. (author)

Full scale tests of moisture buffer capacity of wall materials

DEFF Research Database (Denmark)

Mortensen, Lone Hedegaard; Rode, Carsten; Peuhkuri, Ruut Hannele

2005-01-01

that are harmful such as growth of house dust mites, surface condensation and mould growth. Therefore a series of experiments has been carried out in a full scale test facility to determine the moisture buffer effect of interior walls of cellular concrete and plaster board constructions. For the cellular concrete......Moisture buffer capacity of hygroscopic materials can be used to moderate peaks in the relative humidity (RH) of indoor air as well as moisture content variations in building materials and furnishing. This can help to ensure healthier indoor environments by preventing many processes...... of the changes of moisture content in specimens of the wall composites exposed to the same environment. It was found that the finishes had a big impact on the buffer performance of the underlying materials. Even though the untreated cellular concrete had a very high buffer capacity, the effect was strongly...

Nuclear Calcium Buffering Capacity Shapes Neuronal Architecture*

Science.gov (United States)

Mauceri, Daniela; Hagenston, Anna M.; Schramm, Kathrin; Weiss, Ursula; Bading, Hilmar

2015-01-01

Calcium-binding proteins (CaBPs) such as parvalbumin are part of the cellular calcium buffering system that determines intracellular calcium diffusion and influences the spatiotemporal dynamics of calcium signals. In neurons, CaBPs are primarily localized to the cytosol and function, for example, in nerve terminals in short-term synaptic plasticity. However, CaBPs are also expressed in the cell nucleus, suggesting that they modulate nuclear calcium signals, which are key regulators of neuronal gene expression. Here we show that the calcium buffering capacity of the cell nucleus in mouse hippocampal neurons regulates neuronal architecture by modulating the expression levels of VEGFD and the complement factor C1q-c, two nuclear calcium-regulated genes that control dendrite geometry and spine density, respectively. Increasing the levels of nuclear calcium buffers by means of expression of a nuclearly targeted form of parvalbumin fused to mCherry (PV.NLS-mC) led to a reduction in VEGFD expression and, as a result, to a decrease in total dendritic length and complexity. In contrast, mRNA levels of the synapse pruning factor C1q-c were increased in neurons expressing PV.NLS-mC, causing a reduction in the density and size of dendritic spines. Our results establish a close link between nuclear calcium buffering capacity and the transcription of genes that determine neuronal structure. They suggest that the development of cognitive deficits observed in neurological conditions associated with CaBP deregulation may reflect the loss of necessary structural features of dendrites and spines. PMID:26231212

Efcient Computation of Buffer Capacities for Cyclo-Static Real-Time Systems with Back-Pressure

NARCIS (Netherlands)

Wiggers, M.H.; Bekooij, Marco; Bekooij, Marco Jan Gerrit; Jansen, P.G.; Smit, Gerardus Johannes Maria

2006-01-01

A key step in the design of cyclo-static real-time systems is the determination of buffer capacities. In our multiprocessor system, we apply back-pressure, which means that tasks wait for space in output buffers. Consequently buffer capacities affect the throughput. This requires the derivation of

Moisture buffer capacity of cement-lime plasters with enhanced thermal storage capacity

Science.gov (United States)

Fořt, Jan; Pavlíková, Milena; Pavlík, Zbyšek

2017-07-01

Indoor air temperature and relative humidity represent important parameters for health and working efficiency of buildings occupants. Beside the moderation of temperature, investigation of hygric properties of building materials with connection to indoor relative humidity variation became recognized as a relevant factor for energy efficient building maintenance. The moisture buffer value introduced in the Nordtest protocol can be used for estimation of moisture buffer capacity of building materials or their multi-layered systems. In this paper, both the ideal and real moisture buffer values are examined on the basis of simulation of diurnal relative humidity fluctuations in plasters with incorporated PCM admixture. Retrieved data points to a complex effect of the tested plasters on possible moderation of buildings interior climate.

Salivary pH and buffering capacity in early and late human immunodeficiency virus infection.

Science.gov (United States)

Hegde, Mithra N; Malhotra, Amit; Hegde, Nidarsh D

2013-11-01

Human immunodeficiency virus (HIV) causes severe immunosuppression due to progressive decrease in the CD4 T lymphocyte cells during the course of the disease and this affects all the body systems including glandular secretions. A number of lesions affecting the salivary glands have been noted in HIV infection. The objective of this study was to evaluate the salivary pH and the buffering capacity in HIV positive individuals and comparing it with the HIV negative healthy individuals. The study was carried out on 200 HIV positive subjects aged 20-40 years, divided into two groups on the basis of CD4 count and 100 HIV negative healthy individuals as control group. Both unstimulated and stimulated saliva were collected and the pH and buffering capacity ascertained using the saliva check kit. (GC Asia Dental Pvt. Ltd., Singapore, 508724). All the three groups were compared using the ANOVA and it was found there was highly significant decrease in pH and buffering capacity with increase in immunosuppression. The intergroup comparison was carried out using the Tukey honestly significant difference (HSD) and the Chi square test. Group 1; CD4 count 200 showed a significant decrease in unstimulated salivary flow, stimulated salivary flow, and pH in comparison to HIV negative individuals; however, change in buffering capacity in Group 2 was not significant. There is a decrease in pH and buffering capacity in HIV infected patients. This decrease may be one of the factors responsible for increased caries in HIV infected population.

pH buffering capacity of acid soils from tropical and subtropical regions of China as influenced by incorporation of crop straw biochars

Energy Technology Data Exchange (ETDEWEB)

Xu, Ren-kou; Zhao, An-zhen; Yuan, Jin-hua; Jiang, Jun [Academy of Sciences, Nanjing (China). State Key Lab. of Soil and Sustainable Agriculture

2012-04-15

Purpose: The key factors influencing pH buffering capacity of acid soils from tropical and subtropical regions, and effects of soil evolution and incorporation of biochars on pH buffering capacity were investigated to develop suitable methods to increase pH buffering capacity of acid soils. Materials and methods: A total of 24 acid soils collected from southern China were used. The pH buffering capacity was determined using acid-base titration. The values of pH buffering capacity were obtained from the slope of titration curves of acid or alkali additions plotted against pH in the pH range 4.0-7.0. Two biochars were prepared from straws of peanut and canola using a low temperature pyrolysis method. After incubation of three acid soils, pH buffering capacity was then determined. Results and discussion: pH buffering capacity had a range of 9.1-32.1 mmol kg{sup -1} pH{sup -1} for 18 acid soils from tropical and subtropical regions of China. The pH buffering capacity was highly correlated (R{sup 2} = 0.707) with soil cation exchange capacity (CEC) measured with ammonium acetate method at pH 7.0 and decreased with soil evolution due to the decreased CEC. Incorporation of biochars at rates equivalent to 72 and 120 t ha{sup -1} increased soil pH buffering capacity due to the CEC contained in the biochars. Incorporation of peanut straw char which itself contained more CEC and alkalinity induced more increase in soil CEC, and thus greater increase in pH buffering capacity compared with canola straw char. At 5% of peanut straw char added, soil CEC increased by 80.2%, 51.3%, and 82.8% for Ultisol from Liuzhou, Oxisol from Chengmai and Ultisol from Kunlun, respectively, and by 19.8%, 19.6%, and 32.8% with 5% of canola straw char added, respectively; and correspondingly for these soils, the pH buffering capacity increased by 73.6%, 92.0%, and 123.2% with peanut straw char added; and by 31.3%, 25.6%, and 52.3% with canola straw char added, respectively. Protonation

Nuclear Calcium Buffering Capacity Shapes Neuronal Architecture.

Science.gov (United States)

Mauceri, Daniela; Hagenston, Anna M; Schramm, Kathrin; Weiss, Ursula; Bading, Hilmar

2015-09-18

Calcium-binding proteins (CaBPs) such as parvalbumin are part of the cellular calcium buffering system that determines intracellular calcium diffusion and influences the spatiotemporal dynamics of calcium signals. In neurons, CaBPs are primarily localized to the cytosol and function, for example, in nerve terminals in short-term synaptic plasticity. However, CaBPs are also expressed in the cell nucleus, suggesting that they modulate nuclear calcium signals, which are key regulators of neuronal gene expression. Here we show that the calcium buffering capacity of the cell nucleus in mouse hippocampal neurons regulates neuronal architecture by modulating the expression levels of VEGFD and the complement factor C1q-c, two nuclear calcium-regulated genes that control dendrite geometry and spine density, respectively. Increasing the levels of nuclear calcium buffers by means of expression of a nuclearly targeted form of parvalbumin fused to mCherry (PV.NLS-mC) led to a reduction in VEGFD expression and, as a result, to a decrease in total dendritic length and complexity. In contrast, mRNA levels of the synapse pruning factor C1q-c were increased in neurons expressing PV.NLS-mC, causing a reduction in the density and size of dendritic spines. Our results establish a close link between nuclear calcium buffering capacity and the transcription of genes that determine neuronal structure. They suggest that the development of cognitive deficits observed in neurological conditions associated with CaBP deregulation may reflect the loss of necessary structural features of dendrites and spines. © 2015 by The American Society for Biochemistry and Molecular Biology, Inc.

Ligand-enhanced electrokinetic remediation of metal-contaminated marine sediments with high acid buffering capacity.

Science.gov (United States)

Masi, Matteo; Iannelli, Renato; Losito, Gabriella

2016-06-01

The suitability of electrokinetic remediation for removing heavy metals from dredged marine sediments with high acid buffering capacity was investigated. Laboratory-scale electrokinetic remediation experiments were carried out by applying two different voltage gradients to the sediment (0.5 and 0.8 V/cm) while circulating water or two different chelating agents at the electrode compartments. Tap water, 0.1 M citric acid and 0.1 M ethylenediaminetetraacetic acid (EDTA) solutions were used respectively. The investigated metals were Zn, Pb, V, Ni and Cu. In the unenhanced experiment, the acid front could not propagate due to the high acid buffering capacity of the sediments; the production of OH(-) ions at the cathode resulted in a high-pH environment causing the precipitation of CaCO3 and metal hydroxides. The use of citric acid prevented the formation of precipitates, but solubilisation and mobilisation of metal species were not sufficiently achieved. Metal removal was relevant when EDTA was used as the conditioning agent, and the electric potential was raised up to 0.8 V/cm. EDTA led to the formation of negatively charged complexes with metals which migrated towards the anode compartment by electromigration. This result shows that metal removal from sediments with high acid buffering capacity may be achieved by enhancing the electrokinetic process by EDTA addition when the acidification of the medium is not economically and/or environmentally sustainable.

Rocky Mountain Regional CO{sub 2} Storage Capacity and Significance

Energy Technology Data Exchange (ETDEWEB)

Laes, Denise; Eisinger, Chris; Esser, Richard; Morgan, Craig; Rauzi, Steve; Scholle, Dana; Matthews, Vince; McPherson, Brian

2013-08-30

The purpose of this study includes extensive characterization of the most promising geologic CO{sub 2} storage formations on the Colorado Plateau, including estimates of maximum possible storage capacity. The primary targets of characterization and capacity analysis include the Cretaceous Dakota Formation, the Jurassic Entrada Formation and the Permian Weber Formation and their equivalents in the Colorado Plateau region. The total CO{sub 2} capacity estimates for the deep saline formations of the Colorado Plateau region range between 9.8 metric GT and 143 metric GT, depending on assumed storage efficiency, formations included, and other factors.

Epitaxial integration of CoFe2O4 thin films on Si (001) surfaces using TiN buffer layers

Science.gov (United States)

Prieto, Pilar; Marco, José F.; Prieto, José E.; Ruiz-Gomez, Sandra; Perez, Lucas; del Real, Rafael P.; Vázquez, Manuel; de la Figuera, Juan

2018-04-01

Epitaxial cobalt ferrite thin films with strong in-plane magnetic anisotropy have been grown on Si (001) substrates using a TiN buffer layer. The epitaxial films have been grown by ion beam sputtering using either metallic, CoFe2, or ceramic, CoFe2O4, targets. X-ray diffraction (XRD) and Rutherford spectrometry (RBS) in random and channeling configuration have been used to determine the epitaxial relationship CoFe2O4 [100]/TiN [100]/Si [100]. Mössbauer spectroscopy, in combination with XRD and RBS, has been used to determine the composition and structure of the cobalt ferrite thin films. The TiN buffer layer induces a compressive strain in the cobalt ferrite thin films giving rise to an in-plane magnetic anisotropy. The degree of in-plane anisotropy depends on the lattice mismatch between CoFe2O4 and TiN, which is larger for CoFe2O4 thin films grown on the reactive sputtering process with ceramic targets.

CO2 point sources and subsurface storage capacities for CO2 in aquifers in Norway

International Nuclear Information System (INIS)

Boee, Reidulv; Magnus, Christian; Osmundsen, Per Terje; Rindstad, Bjoern Ivar

2002-01-01

The GESTCO project comprises a study of the distribution and coincidence of thermal CO 2 emission sources and location/quality of geological storage capacity in Europe. Four of the most promising types of geological storage are being studied. 1. Onshore/offshore saline aquifers with or without lateral seal. 2. Low entalpy geothermal reservoirs. 3. Deep methane-bearing coal beds and abandoned coal and salt mines. 4. Exhausted or near exhausted hydrocarbon structures. In this report we present an inventory of CO 2 point sources in Norway (1999) and the results of the work within Study Area C: Deep saline aquifers offshore/near shore Northern and Central Norway. Also offshore/near shore Southern Norway has been included while the Barents Sea is not described in any detail. The most detailed studies are on the Tilje and Aare Formations on the Troendelag Platform off Mid-Norway and on the Sognefjord, Fensfjord and Krossfjord Formations, southeast of the Troll Field off Western Norway. The Tilje Formation has been chosen as one of the cases to be studied in greater detail (numerical modelling) in the project. This report shows that offshore Norway, there are concentrations of large CO 2 point sources in the Haltenbanken, the Viking Graben/Tampen Spur area, the Southern Viking Graben and the central Trough, while onshore Norway there are concentrations of point sources in the Oslofjord/Porsgrund area, along the coast of western Norway and in the Troendelag. A number of aquifers with large theoretical CO 2 storage potential are pointed out in the North Sea, the Norwegian Sea and in the Southern Barents Sea. The storage capacity in the depth interval 0.8 - 4 km below sea level is estimated to be ca. 13 Gt (13000000000 tonnes) CO 2 in geological traps (outside hydrocarbon fields), while the storage capacity in aquifers not confined to traps is estimated to be at least 280 Gt CO 2 . (Author)

Time-related Changes in pH, Buffering Capacity and Phosphate and Urea Concentration of Stimulated Saliva.

Science.gov (United States)

Vuletic, Lea; Peros, Kristina; Spalj, Stjepan; Rogic, Dunja; Alajbeg, Ivan

2014-01-01

To quantify changes in pH, buffering capacity and hydrogen carbonate, phosphate, protein and urea concentrations of stimulated saliva which occur during a 30-min measurement delay after saliva collection. The correlation between time-related chemical changes and changes of salivary pH and buffering capacity was assessed in order to explain the observed changes in salivary pH and buffering capacity. Stimulated saliva samples were collected from 30 volunteers after inducing salivation by chewing a piece of parafilm. Measurements of salivary variables were made immediately after saliva collection and again 30 min later, during which time the specimens were exposed to the atmosphere in collection cups at room temperature. Postponement of measurements resulted in a significant increase in pH and a significant decrease of buffering capacity, phosphate and urea concentration. The results suggest that the time-related pH increase could primarily be attributed to loss of dissolved carbon dioxide from saliva, and confirm the importance of hydrogen carbonate in the neutralisation of hydrogen ions, but they do not support the principle of catalysed phase-buffering for the hydrogen carbonate buffer system in saliva. A decrease in phosphate and urea concentration affects salivary buffering capacity. This study emphasises the importance of the standardisation of measurement time when measuring salivary pH, buffering capacity, phosphate and urea concentrations following the collection of saliva in order to obtain comparable results. It also provides a partial explanation of the mechanisms underlying the observed changes of pH and buffering capacity over time.

Effect of carbonation temperature on CO_2 adsorption capacity of CaO derived from micro/nanostructured aragonite CaCO_3

International Nuclear Information System (INIS)

Hlaing, Nwe Ni; Sreekantan, Srimala; Hinode, Hirofumi; Kurniawan, Winarto; Thant, Aye Aye; Othman, Radzali; Mohamed, Abdul Rahman; Salime, Chris

2016-01-01

Recent years, CaO-based synthetic materials have been attracted attention as potential adsorbents for CO_2 capture mainly due to their high CO_2 adsorption capacity. In this study, micro/nanostructured aragonite CaCO_3 was synthesized by a simple hydrothermal method with using polyacrylamide (PAM). The structural, morphological and thermal properties of the synthesized sample were investigated by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and thermogravimetry analysis (TG-DTA). The XRD and FESEM results showed that the obtained sample was aragonite CaCO_3 with aggregated nanorods and microspheres composed of nanorods. A TG-DTA apparatus with Thermoplus 2 software was used to investigate the effect of carbonation temperature on the CO_2 adsorption capacity of CaO derived from aragonite CaCO_3 sample. At 300 °C, the sample reached the CO_2 adsorption capacity of 0.098 g-CO_2/g-adsorbent, whereas the sample achieved the highest capacity of 0.682 g-CO_2/g-adsorbent at 700 °C. The results showed that the carbonation temperature significantly influenced on the CO_2 adsorption capacity of the CaO derived from aragonite CaCO_3.

Identification and capacity quantification of CO{sub 2} storage sites

Energy Technology Data Exchange (ETDEWEB)

Bachu, Stefan [Energy Resources Conservation Board (Canada)

2008-07-15

In this presentation the subject of scales of evaluation of the sites of CO{sub 2} storage is commented. Also the criteria to identify river basins and sites appropriated for the CO{sub 2} storage are analyzed and finally the matter of the estimation of the capacities of CO{sub 2} storage is analyzed. [Spanish] En esta presentacion se comenta sobre las escalas de evaluacion de los sitios de almacenamiento de CO{sub 2}. Tambien se analizan los criterios para identificar cuencas y lugares adecuados para el almacenamiento de CO{sub 2} y por ultimo se habla sobre la estimacion de las capacidades de almacenamiento de CO{sub 2}.

Study of the buffering capacity, pH and salivary flow rate in type 2 well-controlled and poorly controlled diabetic patients.

Science.gov (United States)

Bernardi, Maria José; Reis, Alessandra; Loguercio, Alessandro Dourado; Kehrig, Ruth; Leite, Mariana Ferreira; Nicolau, José

2007-01-01

This study measured the flow rate, pH and buffering capacity of saliva from well- and poorly metabolically controlled Type 2 diabetic patients in three cities of the southern part of Brazil, compared with healthy individuals from the same cities. Whole saliva was collected by mechanical stimulation and buffering capacity and glucose level were measured. Blood was collected after 12 hours fasting and glucose and glycosylated haemoglobin concentrations were determined. The data were analysed by one-way ANOVA and Student-Newman-Keuls (alpha= 0.05). The flow rate was lower in the Type 2 diabetic patients, regardless of whether they were well or poorly metabolically controlled, compared with healthy individuals (p Salivary glucose concentration was higher in both diabetic patient groups, i.e. well and poorly metabolically controlled, than in the control (p salivary flow rate or the salivary glucose concentration.

Unstimulated salivary flow rate, pH and buffer capacity of saliva in healthy volunteers.

Science.gov (United States)

Fenoll-Palomares, C; Muñoz Montagud, J V; Sanchiz, V; Herreros, B; Hernández, V; Mínguez, M; Benages, A

2004-11-01

To assess the salivary flow rate, pH, and buffer capacity of healthy volunteers, and their relationships with age, gender, obesity, smoking, and alcohol consumption, and to establish the lower-end value of normal salivary flow (oligosialia). A prospective study was conducted in 159 healthy volunteers (age > 18 years, absence of medical conditions that could decrease salivary flow). Unstimulated whole saliva was collected during ten minutes, and salivary flow rate (ml/min), pH, and bicarbonate concentration (mmol/l) were measured using a Radiometer ABL 520. The 5 percentile of salivary flow rate and bicarbonate concentration was considered the lower limit of normality. Median salivary flow rate was 0.48 ml/min (range: 0.1-2 ml/min). Age younger than 44 years was associated with higher flow rates (OR 2.10). Compared with women, men presented a higher flow rate (OR 3.19) and buffer capacity (OR 2.81). Bicarbonate concentration correlated with salivary flow rate. The lower-end values of normal flow rate and bicarbonate concentration were 0.15 ml/min and 1.800 mmol/l, respectively. The presence of obesity, smoking, and alcohol consumption did not influence salivary parameters. In healthy volunteers, salivary flow rate depends on age and gender, and correlates with buffer capacity. Obesity, smoking, and alcohol use do not influence salivary secretion.

Buffer capacity of food components influences the acid tolerance response in Salmonella Typhimurium during simulated gastric passage

DEFF Research Database (Denmark)

Henriksen, Sidsel; Buschhardt, Tasja; Hansen, Tina Beck

2014-01-01

tubes, enabling simultaneous testing of biological triplicates under varying conditions. Surprisingly, we found that less buffered media provided higher protection of Salmonella, compared to media with high buffer capacity. By investigating the relative gene expression of rpoS and ompR encoding for two...... Heart Infusion Broth having a higher buffer capacity. We suggest this to be associated with a varying ability of Salmonella Typhimurium to mount a stationary phase acid tolerance response (ATR) depending on the buffer capacity of the food vehicle....

[On possible approach to characterizing the buffering capacity of landscape with respect to radiocesium contamination].

Science.gov (United States)

Frid, A S

2005-01-01

It is shown that migration (equally with decay) is a mechanism responsible for the buffering capacity of landscape with respect to radiocesium contamination. An approach is offered to determine the gradation of the buffering capacity and corresponding parameters of the migration models.

There is no capacity limited buffer in the Murdock (1962) free recall data

OpenAIRE

Tarnow, Eugen

2010-01-01

Theories of short term memory often include a limited capacity “buffer”. Such a buffer contains items which do not decay at all but are overwritten by new data. I show that one of the experiments that fueled the buffer concept, the free recall experiments by Murdock (J Exp Psychol 64(5):482–488, 1962), does not contain such a buffer.

Heat capacities of several Co{sub 2}YZ Heusler compounds

Energy Technology Data Exchange (ETDEWEB)

Yin, Ming, E-mail: myin1@hawk.iit.edu; Nash, Philip; Chen, Song

2013-12-20

Highlights: • Heat contents from 600 K to 1500 K of selected Co{sub 2}YZ were measured by drop calorimeters. • Heat capacities were obtained by taking derivatives of heats contents which were fitted with second order polynomial with respect to temperature. • Melting points determined by DSC were consistent with literature data. • Heats of fusion determined by DSC were comparable with those obtained by extrapolation of heat contents. - Abstract: Heat contents of several Co{sub 2}-based Heusler compounds Co{sub 2}YZ (Y = Fe, Mn, Ti; Z = Al, Ga, Si, Ge, Sn) were measured from 500 K to 1500 K using a Setaram MTHC 96 drop calorimeter. Second order polynomials were adopted to fit the data and heat capacities were obtained by taking the derivatives with respect to temperature. Melting points were determined by differential scanning calorimetry (DSC) and measured heats of fusion were compared with those obtained from extrapolation of heat contents.

Salivary pH and Buffering Capacity as Risk Markers for Early Childhood Caries: A Clinical Study.

Science.gov (United States)

Jayaraj, D; Ganesan, S

2015-01-01

The diagnostic utility of saliva is currently being explored in various branches of dentistry, remarkably in the field of caries research. This study was aimed to determine if assessment of salivary pH and buffering capacity would serve as reliable tools in risk prediction of early childhood caries (ECC). Paraffin-stimulated salivary samples were collected from 50 children with ECC (group I) and 50 caries free children (group II). Salivary pH and buffering capacity (by titration with 0.1 N hydrochloric acid) were assessed using a handheld digital pH meter in both groups. The data obtained were subjected to statistical analysis. Statistically, no significant difference was observed between both the groups for all salivary parameters assessed, except for the buffering capacity level at 150 μl titration of 0.1 N hydrochloric acid (p = 0.73; significant at 1% level). Salivary pH and buffering capacity may not serve as reliable markers for risk prediction of ECC. How to cite this article: Jayaraj D, Ganesan S. Salivary pH and Buffering Capacity as Risk Markers for Early Childhood Caries: A Clinical Study. Int J Clin Pediatr Dent 2015;8(3):167-171.

The potential effects of pH and buffering capacity on dental erosion.

Science.gov (United States)

Owens, Barry M

2007-01-01

Soft drink pH (initial pH) has been shown to be a causative factor--but not necessarily the primary initiating factor--of dental erosion. The titratable acidity or buffering capacity has been acknowledged as playing a significant role in the etiology of these lesions. This in vitro study sought to evaluate five different soft drinks (Coca-Cola Classic, Diet Coke, Gatorade sports drink, Red Bull high-energy drink, Starbucks Frappucino coffee drink) and tap water (control) in terms of initial pH and buffering capacity. Initial pH was measured in triplicate for the six beverages. The buffering capacity of each beverage was assessed by measuring the weight (in grams) of 0.10 M sodium hydroxide necessary for titration to pH levels of 5.0, 6.0, 7.0, and 8.3. Coca-Cola Classic produced the lowest mean pH, while Starbucks Frappucino produced the highest pH of any of the drinks except for tap water. Based on statistical analysis using ANOVA and Fisher's post hoc tests at a P Starbucks Frappucino.

Effect of carbonation temperature on CO{sub 2} adsorption capacity of CaO derived from micro/nanostructured aragonite CaCO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Hlaing, Nwe Ni, E-mail: nwenihlaing76@gmail.com [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Sreekantan, Srimala, E-mail: srimala@usm.my [School of Materials and Mineral Resources Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Hinode, Hirofumi, E-mail: hinode@ide.titech.ac.jp; Kurniawan, Winarto, E-mail: Kurniawan.w.ab@m.titech.ac.jp [Department of International Development Engineering, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro-ku, Tokyo (Japan); Thant, Aye Aye, E-mail: a2thant@gmail.com [Department of Physics, University of Yangon, 11041 Kamayut, Yangon (Myanmar); Othman, Radzali, E-mail: radzali@utem.edu.my [Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Malacca (Malaysia); Mohamed, Abdul Rahman, E-mail: chrahman@eng.usm.my [Low Carbon Economy (LCE) Research Group, School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Salime, Chris, E-mail: chris.salim@surya.ac.id [Environmental Engineering, Surya University, Tangerang, 15810 Banten (Indonesia)

2016-07-06

Recent years, CaO-based synthetic materials have been attracted attention as potential adsorbents for CO{sub 2} capture mainly due to their high CO{sub 2} adsorption capacity. In this study, micro/nanostructured aragonite CaCO{sub 3} was synthesized by a simple hydrothermal method with using polyacrylamide (PAM). The structural, morphological and thermal properties of the synthesized sample were investigated by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) and thermogravimetry analysis (TG-DTA). The XRD and FESEM results showed that the obtained sample was aragonite CaCO{sub 3} with aggregated nanorods and microspheres composed of nanorods. A TG-DTA apparatus with Thermoplus 2 software was used to investigate the effect of carbonation temperature on the CO{sub 2} adsorption capacity of CaO derived from aragonite CaCO{sub 3} sample. At 300 °C, the sample reached the CO{sub 2} adsorption capacity of 0.098 g-CO{sub 2}/g-adsorbent, whereas the sample achieved the highest capacity of 0.682 g-CO{sub 2}/g-adsorbent at 700 °C. The results showed that the carbonation temperature significantly influenced on the CO{sub 2} adsorption capacity of the CaO derived from aragonite CaCO{sub 3}.

Buffer capacity of food components influences the acid tolerance response in Salmonella Typhimurium during simulated gastric passage

DEFF Research Database (Denmark)

Aabo, Søren; Buschhardt, Tasja; Hansen, Tina Beck

2014-01-01

Food composition, buffer capacity, and fat and protein content have been shown to effect the gastric acid survival of pathogens (Waterman & Small 1998). In this study, simple food-model substances with different buffer capacities were investigated for their ability to support survival of stationary...... Heart Infusion Broth having a higher buffer capacity. We suggest this to be associated with a varying ability of Salmonella Typhimurium to mount a stationary phase acid tolerance response (ATR) depending on the buffer capacity of the food vehicle....... phase Salmonella Typhimurium during simulated gastric acid passage. We used a computer-controlled fermentor to employ pH changes in synthetic gastric fluid, mimicking the dynamic pH during gastric passage. In order to minimise variation, Salmonella enterica serovar Typhimurium was contained in dialysis...

CO2 Capacity Sorbent Analysis Using Volumetric Measurement Approach

Science.gov (United States)

Huang, Roger; Richardson, Tra-My Justine; Belancik, Grace; Jan, Darrell; Knox, Jim

2017-01-01

In support of air revitalization system sorbent selection for future space missions, Ames Research Center (ARC) has performed CO2 capacity tests on various solid sorbents to complement structural strength tests conducted at Marshall Space Flight Center (MSFC). The materials of interest are: Grace Davison Grade 544 13X, Honeywell UOP APG III, LiLSX VSA-10, BASF 13X, and Grace Davison Grade 522 5A. CO2 capacity was for all sorbent materials using a Micromeritics ASAP 2020 Physisorption Volumetric Analysis machine to produce 0C, 10C, 25C, 50C, and 75C isotherms. These data are to be used for modeling data and to provide a basis for continued sorbent research. The volumetric analysis method proved to be effective in generating consistent and repeatable data for the 13X sorbents, but the method needs to be refined to tailor to different sorbents.

Activation of a Ca-bentonite as buffer material

Science.gov (United States)

Huang, Wei-Hsing; Chen, Wen-Chuan

2016-04-01

Swelling behavior is an important criterion in achieving the low-permeability sealing function of buffer material. A potential buffer material may be used for radioactive waste repository in Taiwan is a locally available clayey material known as Zhisin clay, which has been identified as a Ca-bentonite. Due to its Ca-based origin, Zhisin was found to exhibit swelling capacity much lower than that of Na-bentonite. To enhance the swelling potential of Zhisin clay, a cation exchange process by addition of Na2CO3 powder was introduced in this paper. The addition of Na2CO3 reagent to Zhisin clay, in a liquid phase, caused the precipitation of CaCO3 and thereby induced a replacement of Ca2+ ions by Na+ ions on the surface of bentonite. Characterization test conducted on Zhisin clay includes chemical analysis, cation exchange capacity, X-ray diffraction, and thermogravimetry (TG). Free-swelling test apparatus was developed according to International Society of Rock Mechanics recommendations. A series of free-swelling tests were conducted on untreated and activated specimens to characterize the effect of activation on the swelling capacity of Zhisin clay. Efforts were made to determine an optimum dosage for the activation, and to evaluate the aging effect. Also, the activated material was evaluated for its stability in various hydrothermal conditions for potential applications as buffer material in a repository. Experimental results show that Na2CO3-activated Zhisin clay is superior in swelling potential to untreated Zhisin clay. Also, there exists an optimum amount of activator in terms of improvements in the swelling capacity. A distinct time-swell relationship was discovered for activated Zhisin clay. The corresponding mechanism refers to exchange of cations and breakdown of quasi-crystal, which results in ion exchange hysteresis of Ca-bentonite. Due to the ion exchange hysteresis, activated bentonite shows a post-rise time-swell relationship different than the sigmoid

Low Buffer Capacity and Alternating Motility along the Human Gastrointestinal Tract: Implications for in Vivo Dissolution and Absorption of Ionizable Drugs.

Science.gov (United States)

Hens, Bart; Tsume, Yasuhiro; Bermejo, Marival; Paixao, Paulo; Koenigsknecht, Mark J; Baker, Jason R; Hasler, William L; Lionberger, Robert; Fan, Jianghong; Dickens, Joseph; Shedden, Kerby; Wen, Bo; Wysocki, Jeffrey; Loebenberg, Raimar; Lee, Allen; Frances, Ann; Amidon, Greg; Yu, Alex; Benninghoff, Gail; Salehi, Niloufar; Talattof, Arjang; Sun, Duxin; Amidon, Gordon L

2017-12-04

In this study, we determined the pH and buffer capacity of human gastrointestinal (GI) fluids (aspirated from the stomach, duodenum, proximal jejunum, and mid/distal jejunum) as a function of time, from 37 healthy subjects after oral administration of an 800 mg immediate-release tablet of ibuprofen (reference listed drug; RLD) under typical prescribed bioequivalence (BE) study protocol conditions in both fasted and fed states (simulated by ingestion of a liquid meal). Simultaneously, motility was continuously monitored using water-perfused manometry. The time to appearance of phase III contractions (i.e., housekeeper wave) was monitored following administration of the ibuprofen tablet. Our results clearly demonstrated the dynamic change in pH as a function of time and, most significantly, the extremely low buffer capacity along the GI tract. The buffer capacity on average was 2.26 μmol/mL/ΔpH in fasted state (range: 0.26 and 6.32 μmol/mL/ΔpH) and 2.66 μmol/mL/ΔpH in fed state (range: 0.78 and 5.98 μmol/mL/ΔpH) throughout the entire upper GI tract (stomach, duodenum, and proximal and mid/distal jejunum). The implication of this very low buffer capacity of the human GI tract is profound for the oral delivery of both acidic and basic active pharmaceutical ingredients (APIs). An in vivo predictive dissolution method would require not only a bicarbonate buffer but also, more significantly, a low buffer capacity of dissolution media to reflect in vivo dissolution conditions.

High-resolution electron microscopy study of Ni81Fe19 film with Co33Cr67 buffer layer

International Nuclear Information System (INIS)

Xu, Q.Y.; Wang, Z.M.; Shen, F.; Du, Y.W.; Zhang, Z.

2003-01-01

The anisotropic magnetoresistance (AMR) in permalloy Ni 81 Fe 19 film deposited on a 1.2 nm Co 33 Cr 67 buffer layer was significantly enhanced. The high-resolution electron microscopy was used to study the microstructure of Ni 81 Fe 19 film with and without Co 33 Cr 67 buffer layer. It was found that Co 33 Cr 67 buffer layer can induce good (1 1 1) texture, while without Co 33 Cr 67 buffer layer, Ni 81 Fe 19 film show randomly oriented grain structure. The Δρ/ρ enhancement is attributed to the decrease in the resistivity ρ of the Ni 81 Fe 19 film due to the formation of the large (1 1 1) textured grains in Ni 81 Fe 19 film with Co 33 Cr 67 buffer layer. However, the surface roughness of substrate may limit the (1 1 1) textured grain size and induce additional grain boundaries in Ni 81 Fe 19 film with Co 33 Cr 67 buffer layer, limit the enhancement of the AMR effect

On the limits of CO2 capture capacity of carbons

OpenAIRE

Fernández Martín, Claudia; González Plaza, Marta; Pis Martínez, José Juan; Rubiera González, Fernando; Pevida García, Covadonga; Álvarez Centeno, Teresa

2010-01-01

This study shows that standard techniques used for carbons characterization, such as physical adsorption of CO2 at 273 K and N2 at 77 K, can be used to assess, with a good accuracy, the maximum capacity of carbons to capture CO2 under post- and pre-combustion conditions. The analysis of the corresponding adsorption isotherms, within the general theoretical framework of Dubinin's theory, leads to the values of the micropore volume, Wo, and the characteristic energy, Eo, of the carbons, which p...

A high capacity FASTBUS multiple event buffer

International Nuclear Information System (INIS)

Appel, J.A.; Farr, W.D.; Kaplan, D.M.; Levit, L.B.; Napier, T.M.

1985-01-01

We have developed a front-end data acquisition and event buffering memory. This single-width FASTBUS module has a capacity of 256K X 32 bits plus parity. The module is dual ported, and its front panel ECLport accepts data at up to 20 MB/sec. It may also be written to and read from as a standard FASTBUS Slave. The module records events as variable length records. Each record is accepted or rejected via front panel control signal. Circuitry to automate FASTBUS record readout and record skip is provided. In its ''linear'' mode, the module may be used as a single pass list. Alternatively, in the ''circular'' mode, the module's internal read pointer can follow its write pointer continuously around the memory. Circular mode is well suited to handling of a continuous data stream. Modules may be linked for larger memory capacity

Determination of buffering capacity of selected fermented feedstuffs and the effect of dietary acid-base status on ruminal fluid pH

Directory of Open Access Journals (Sweden)

Lukáš Bujňák

2011-01-01

Full Text Available The aim of this study was to evaluate the buffering capacity of some fermented feedstuffs and the effect of dietary acid-base status on ruminal fluid pH. The first experiment was performed with different types (n = 24 of wet and dry fermented feedstuffs to determine the buffering capacity and buffer value index. The buffer value index of wet corn silages was more negative than for dry corn silages account on acid loss during drying. In the second experiment, the effects of different concentrations of lactic acid on base-buffering capacity, buffer value index and indicators of fermentation process were studied in two groups of corn silages (n = 21. Two groups of analyzed values were compared using unpaired t-test. Differences among the groups in base-buffering capacity (P P P > 0.05 correlation was found between ruminal pH and dietary buffer value index. These results confirmed that dietary acid-base status alone is not adequate as a predictor of the need for buffers in the diet of lactating cows. It is the first report about using of buffering capacity determination methods for evaluation of feedstuffs and dietary acid-base status in dairy cows.

Optimal capacity and buffer size estimation under Generalized Markov Fluids Models and QoS parameters

International Nuclear Information System (INIS)

Bavio, José; Marrón, Beatriz

2014-01-01

Quality of service (QoS) for internet traffic management requires good traffic models and good estimation of sharing network resource. A link of a network processes all traffic and it is designed with certain capacity C and buffer size B. A Generalized Markov Fluid model (GMFM), introduced by Marrón (2011), is assumed for the sources because describes in a versatile way the traffic, allows estimation based on traffic traces, and also consistent effective bandwidth estimation can be done. QoS, interpreted as buffer overflow probability, can be estimated for GMFM through the effective bandwidth estimation and solving the optimization problem presented in Courcoubetis (2002), the so call inf-sup formulas. In this work we implement a code to solve the inf-sup problem and other optimization related with it, that allow us to do traffic engineering in links of data networks to calculate both, minimum capacity required when QoS and buffer size are given or minimum buffer size required when QoS and capacity are given

Dissolution properties of co-amorphous drug-amino acid formulations in buffer and biorelevant media.

Science.gov (United States)

Heikkinen, A T; DeClerck, L; Löbmann, K; Grohganz, H; Rades, T; Laitinen, R

2015-07-01

Co-amorphous formulations, particularly binary drug-amino acid mixtures, have been shown to provide enhanced dissolution for poorly-soluble drugs and improved physical stability of the amorphous state. However, to date the dissolution properties (mainly intrinsic dissolution rate) of the co-amorphous formulations have been tested only in buffers and their supersaturation ability remain unexplored. Consequently, dissolution studies in simulated intestinal fluids need to be conducted in order to better evaluate the potential of these systems in increasing the oral bioavailability of biopharmaceutics classification system class II drugs. In this study, solubility and dissolution properties of the co-amorphous simvastatin-lysine, gibenclamide-serine, glibenclamide-threonine and glibenclamide-serine-threonine were studied in phosphate buffer pH 7.2 and biorelevant media (fasted and fed state simulated intestinal fluids (FaSSIF and FeSSIF, respectively)). The co-amorphous formulations were found to provide a long-lasting supersaturation and improve the dissolution of the drugs compared to the crystalline and amorphous drugs alone in buffer. Similar improvement, but in lesser extent, was observed in biorelevant media suggesting that a dissolution advantage observed in aqueous buffers may overestimate the advantage in vivo. However, the results show that, in addition to stability advantage shown earlier, co-amorphous drug-amino acid formulations provide dissolution advantage over crystalline drugs in both aqueous and biorelevant conditions.

Amine-Functionalized Amino Acid-based Ionic Liquids as Efficient and High-Capacity Absorbents for CO2

DEFF Research Database (Denmark)

Shunmugavel, Saravanamurugan; Kunov-Kruse, Andreas Jonas; Fehrmann, Rasmus

2014-01-01

Ionic liquids (ILs) comprised of ammonium cations and anions of naturally occurring amino acids containing an additional amine group (e.g., lysine, histidine, asparagine, and glutamine) were examined as high-capacity absorbents for CO2. An absorption capacity of 2.1 mol CO2 per mol of IL (3.5 mol...

Organellar Calcium Buffers

Science.gov (United States)

Prins, Daniel; Michalak, Marek

2011-01-01

Ca2+ is an important intracellular messenger affecting many diverse processes. In eukaryotic cells, Ca2+ storage is achieved within specific intracellular organelles, especially the endoplasmic/sarcoplasmic reticulum, in which Ca2+ is buffered by specific proteins known as Ca2+ buffers. Ca2+ buffers are a diverse group of proteins, varying in their affinities and capacities for Ca2+, but they typically also carry out other functions within the cell. The wide range of organelles containing Ca2+ and the evidence supporting cross-talk between these organelles suggest the existence of a dynamic network of organellar Ca2+ signaling, mediated by a variety of organellar Ca2+ buffers. PMID:21421925

Absorption capacity and viscosity for CO_2 capture process using high concentrated PZ-DEAE aqueous solution

International Nuclear Information System (INIS)

Fu, Dong; Wang, LeMeng; Mi, ChenLu; Zhang, Pan

2016-01-01

Highlights: • Absorption of CO_2 in high concentrated DEAE-PZ aqueous solutions were measured. • Viscosities of CO_2-unloaded and CO_2-loaded DEAE-PZ aqueous solutions were measured. • Weiland equation was used to calculate the viscosities. • Effects of temperature, concentration and CO_2 loading on viscosity were demonstrated. - Abstract: The absorption capacity of CO_2 in piperazine (PZ) promoted 2-diethylaminoethanol (DEAE) aqueous solution was measured. The viscosities of both CO_2-unloaded and CO_2-loaded PZ-DEAE aqueous solutions were measured and then modelled. The temperatures ranged from 303.2 K to 323.2 K. The mass fraction of PZ and DEAE respectively ranged from 0 to 0.075 and 0.3 to 0.5. The temperature and concentration dependences of absorption capacity were determined. The effects of temperature, mass fraction and CO_2 loading on viscosities are demonstrated.

The acid-base buffer capacity of podzolic soils and its changes under the impact of treatment with the Mehra-Jackson and Tamm reagents

Science.gov (United States)

Maksimova, Yu. G.; Maryakhina, N. N.; Tolpeshta, I. I.; Sokolova, T. A.

2010-10-01

The acid-base buffer capacity before and after the treatment with the Mehra-Jackson and Tamm reagents was assessed by continuous potentiometric titration for the main genetic horizons of two profiles of podzolic soils in the Central Forest State Reserve. The total buffer capacity was calculated in the pH range from the initial titration point (ITP) to 3 for the acid titration and from the ITP to 10 for the base titration, as well as the buffer capacities in the pH intervals of 0.25. It was found that both treatments abruptly decreased the base buffer capacity, which reached 70-90% in the E horizons. The high direct linear correlation of the difference between the total base buffer capacities before and after each treatment with the content of Fe in the Tamm extract was revealed. From the results obtained, a conclusion was drawn that finely dispersed Fe hydroxides were the main solid-phase constituents ensuring the base buffer capacity, and the deprotonation of hydroxyl groups on the surface of Fe hydroxides was the essential buffer reaction during the base titration.

Moisture buffering capacity of highly absorbing materials

Energy Technology Data Exchange (ETDEWEB)

Cerolini, S.; D' Orazio, M.; Stazi, A. [Department of Architecture, Construction and Structures (DACS), Faculty of Engineering, Polytechnic University of Marche, Via Brecce Bianche, 60100 Ancona (Italy); Di Perna, C. [Department of Energetics, Faculty of Engineering, Polytechnic University of Marche, Via Brecce Bianche, 60100 Ancona (Italy)

2009-02-15

This research investigates the possibility to use highly absorbing materials to dampen indoor RH% variations. The practical MBV of sodium polyacrylate, cellulose-based material, perlite and gypsum is evaluated for a daily cyclic exposure that alternates high (75%) and low (33%) RH% levels for 8 h and 16 h, respectively. The adjustment velocity to RH% variations and the presence of hysteretic phenomena are also presented. The cellulose-based material proves to be the most suitable for moisture buffering applications. Starting from this material's properties, the effect of thickness, vapour resistance factor ({mu}) and mass surface exchange coefficient (Z{sub v}) on sorption capacity is evaluated by the use of a numerical model. (author)

In-situ X-ray absorption spectroscopy analysis of capacity fade in nanoscale-LiCoO2

International Nuclear Information System (INIS)

Patridge, Christopher J.; Love, Corey T.; Swider-Lyons, Karen E.; Twigg, Mark E.; Ramaker, David E.

2013-01-01

The local structure of nanoscale (∼10–40 nm) LiCoO 2 is monitored during electrochemical cycling utilizing in-situ X-ray absorption spectroscopy (XAS). The high surface area of the LiCoO 2 nanoparticles not only enhances capacity fade, but also provides a large signal from the particle surface relative to the bulk. Changes in the nanoscale LiCoO 2 metal-oxide bond lengths, structural disorder, and chemical state are tracked during cycling by adapting the delta mu (Δμ) technique in complement with comprehensive extended X-ray absorption fine structure (EXAFS) modeling. For the first time, we use a Δμ EXAFS method, and by comparison of the difference EXAFS spectra, extrapolate significant coordination changes and reduction of cobalt species with cycling. This combined approach suggests Li–Co site exchange at the surface of the nanoscale LiCoO 2 as a likely factor in the capacity fade and irreversible losses in practical, microscale LiCoO 2 . - Graphical abstract: Electrochemical cycling of Li-ion batteries has strong impact on the structure and integrity of the cathode active material particularly near the surface/electrolyte interface. In developing a new method, we have used in-situ X-ray absorption spectroscopy during electrochemical cycling of nanoscale LiCoO 2 to track changes during charge and discharge and between subsequent cycles. Using difference spectra, several small changes in Co-O bond length, Co-O and Co-Co coordination, and site exchange between Co and Li sites can be tracked. These methods show promise as a new technique to better understand processes which lead to capacity fade and loss in Li-ion batteries. - Highlights: • A new method is developed to understand capacity fade in Li-ion battery cathodes. • Structural changes are tracked during Li intercalation/deintercalation of LiCoO 2 . • Surface structural changes are emphasized using nanoscale-LiCoO 2 and difference spectra. • Full multiple scattering calculations are used to

Correlation of Dental Caries Experience with pH, Buffering Capacity and Flow Rate of Saliva among 15-year-old School Children in Mangalore

Directory of Open Access Journals (Sweden)

Vijay S Kumar

2013-01-01

Full Text Available Aim and Objectives: To correlate dental caries experience with pH, buffering capacity and flow rate of saliva among 15-year-old-children Materials & Method : Fifteen year old school children from adopted schools of a dental college in Mangalore were considered as study subjects. The study was carried out using a standardized proforma that consisted of questionnaire for recording demographic data. The caries experience was assessed by DMFT Index. Salivary pH was measured by using a pH meter and salivary buffering capacity was measured by using titration method. Unstimulated whole saliva was collected from all subjects by direct expectoration to calculate the flow rate. Results: The mean DMFT of the study population was 2.85 ± 2.5. The mean salivary pH was found to be 6.88 ± 0.69.About 74.1% were having medium salivary buffering capacities. The mean unstimulated salivary flow rate and mean total antioxidant capacity of the study population was 0.41 ± 0.14 ml/min and 94.15 ± 60.72 g/dL respectively. Conclusions: A marked association between the pH, buffering capacity and unstimulated flow rate with dental caries experience suggest that assessment of these salivary parameters can be used as predictors for future dental caries susceptibility in an individual.

Tunnel magnetoresistance of an as-deposited Co2FeAl0.5Si0.5-based magnetic tunnel junction on a Ta/Ru buffer layer

International Nuclear Information System (INIS)

Hwang, Jae Youn; Lee, Gae Hun; Song, Yun Heub; Yim, Hae In

2010-01-01

A magnetic tunnel junction (MTJ) with a Co 2 FeAl 0.5 Si 0.5 (CFAS) heusler film on a conductive Ta/Ru buffer layer was fabricated for the first time. In the as-deposited state, a highly B2-ordered CFAS film was obtained by using the Ta/Ru buffer layer. The Ta (110) buffer layer causes a Ru (002) buffer layer, which leads to the growth of CFAS with a B2 structure and a completely flat CFAS film. After 600 .deg. C annealing, strain relaxation occurred in the Ta/Ru interface, and the surface roughness decreased; however, the B2-ordered CFAS film remained. Also, in the as-deposited state, a exchange-biased CFAS/AlO x /CFAS MTJ deposited on a Ta/Ru buffer layer exhibited a relatively high tunnel magnetoresistance (TMR) of 13% at room temperature, which resulted from the highly B2-ordered CFAS layer and the perfectly flat surface roughness resulting from the use of the Ta/Ru buffer layer.

The impact of CO2 on shallow groundwater chemistry: observations at a natural analog site and implications for carbon sequestration

Energy Technology Data Exchange (ETDEWEB)

Keating, Elizabeth [Los Alamos National Laboratory; Fessenden, Julianna [Los Alamos National Laboratory; Kanjorski, Nancy [NON LANL; Koning, Dan [NM BUREAU OF GEOLOGY AND MINERAL RESOURCES; Pawar, Rajesh [Los Alamos National Laboratory

2008-01-01

In a natural analog study of risks associated with carbon sequestration, impacts of CO{sub 2} on shallow groundwater quality have been measured in a sandstone aquifer in New Mexico, USA. Despite relatively high levels of dissolved CO{sub 2}, originating from depth and producing geysering at one well, pH depression and consequent trace element mobility are relatively minor effects due to the buffering capacity of the aquifer. However, local contamination due to influx of saline waters in a subset of wells is significant. Geochemical modeling of major ion concentrations suggests that high alkalinity and carbonate mineral dissolution buffers pH changes due to CO{sub 2} influx. Analysis oftrends in dissolved trace elements, chloride, and CO2 reveal no evidence of in-situ trace element mobilization. There is clear evidence, however, that As, U, and Pb are locally co-transported into the aquifer with CO{sub 2}-rich saline water. This study illustrates the role that local geochemical conditions will play in determining the effectiveness of monitoring strategies for CO{sub 2} leakage. For example, if buffering is significant, pH monitoring may not effectively detect CO2 leakage. This study also highlights potential complications that CO{sub 2}carrier fluids, such as saline waters, pose in monitoring impacts ofgeologic sequestration.

Improved CO_2 adsorption capacity and cyclic stability of CaO sorbents incorporated with MgO

International Nuclear Information System (INIS)

Farah Diana Mohd Daud; Kumaravel Vignesh; Srimala Sreekantan; Abdul Rahman Mohamed

2016-01-01

Calcium oxide (CaO) sorbents incorporated with magnesium oxide (MgO) were synthesized using a co-precipitation route. The sorbents were prepared with different MgO concentrations (from 5 wt% to 30 wt%). The as-prepared sorbents were characterized using X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDX) and BET surface area analysis techniques. The sintering effect of CaO sorbents was decreased after the incorporation of MgO. The sorbents with 5 wt% and 10 wt% of MgO retained their CO_2 adsorption capacity over multiple cycles. Most importantly, CaO with 10 wt% MgO showed constant CO_2 adsorption capacity over 30 carbonation cycles. The results revealed that CaO with 10 wt% MgO is sufficient to produce sorbents with high surface area, good structural stability and enhanced CO_2 adsorption capacity. (authors)

Comparison and trend study on acidity and acidic buffering capacity of particulate matter in China

Science.gov (United States)

Ren, Lihong; Wang, Wei; Wang, Qingyue; Yang, XiaoYang; Tang, Dagang

2011-12-01

The acidity of about 2000 particulate matter samples from aircraft and ground-based monitoring is analyzed by the method similar to soil acidity determination. The ground-based samples were collected at about 50 urban or background sites in northern and southern China. Moreover, the acidic buffering capacity of those samples is also analyzed by the method of micro acid-base titration. Results indicate that the acidity level is lower in most northern areas than those in the south, and the acidic buffering capacity showed inverse tendency, correspondingly. This is the most important reason why the pollution of acidic-precipitation is much more serious in Southern China than that in Northern China. The acidity increases and the acidic buffering capacity drops with the decreasing of the particle sizes, indicating that fine particle is the main influencing factor of the acidification. The ionic results show that Ca salt is the main alkaline substance in particulate matter, whereas the acidification of particulate matter is due to the SO 2 and NO x emitted from the fossil fuel burning. And among of them, coal burning is the main contributor of SO 2, however the contribution of NO x that emitted from fuel burning of motor vehicles has increased in recent years. By comparison of the experimental results during the past 20 years, it can be concluded that the acid precipitation of particulate matter has not been well controlled, and it even shows an increasing tendency in China lately. The acid precipitation of particulate matter has begun to frequently attack in part of the northern areas. Multiple regression analysis indicates that coefficient value of the ions is the lowest at the urban sites and the highest at the regional sites, whereas the aircraft measurement results are intermediate between those two kinds of sites.

[Relationship between blood glucose levels and salivary pH and buffering capacity in type II diabetes patients].

Science.gov (United States)

Elkafri, I H; Mashlah, A; Shaqifa, A

2014-03-13

This study was evaluated the relationship between blood glucose levels and salivary pH and buffering capacity in type II diabetic patients. The sample comprised 210 participants (age ranged 40-60 years). Based on fasting blood glucose levels the participants were divided into 3 groups: controls with normal blood glucose levels; diabetic patients with levels ≤ 200 mg/dL; and diabetic patients with levels > 200 mg/dL. Salivary pH and buffering capacity were determined in a sample of resting (non-stimulated) saliva taken from each participant. Salivary pH levels in diabetic patients with blood glucose levels > 200 mg/dL were lower than in the controls and diabetic patients with levels ≤ 200 mg/dL. Salivary pH levels were comparable in controls and diabetic patients with blood glucose levels ≤ 200 mg/dL. Salivary buffering capacity in the 3 groups was comparable.

History of CO/sub 2/

Energy Technology Data Exchange (ETDEWEB)

Degens, E T

1979-01-01

Upon arrival on earth, the reduced carbon pool split into a series of compartments: core, mantle, crust, hydrosphere, atmosphere, and biosphere. This distribution pattern is caused by the ability of carbon to adjust structurally to a wide range of pressure and temperature, and to form simple and complex molecules with oxygen, hydrogen and nitrogen. Transformation also involved oxidation of carbon to CO/sub 2/ which is mediated at depth by minerals, such as magnetite, and by water vapor above critical temperature. Guided by mineral-organic interactions, simple carbon compounds evolved in near surface environments towards physiologically interesting biochemicals. Life, as an autocatalytic system, is considered an outgrowth of such a development. This article discusses environmental parameters that control the CO/sub 2/ system, past and present. Mantle and crustal evolution is the dynamo recharging the CO/sub 2/ in sea and air; the present rate of CO/sub 2/ release from the magma is 0.05 x 10/sup 15/ g C per year. Due to the enormous buffer capacity of the chemical system ocean, such rates are too small to seriously effect the level of CO/sub 2/ in our atmosphere. In the light of geological field data and stable isotope work, it is concluded that the CO/sub 2/ content in the atmosphere has remained fairly uniform since early Precambrian time; CO/sub 2/ should thus have had little impact on paleoclimate. In contrast, the massive discharge of man-made CO/sub 2/ into our atmosphere may have serious consequences for climate, environment and society in the years to come.

In-situ X-ray absorption spectroscopy analysis of capacity fade in nanoscale-LiCoO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Patridge, Christopher J. [NRC/NRL Cooperative Research Associate, U.S. Naval Research Laboratory, Washington, DC 20375 (United States); Love, Corey T., E-mail: corey.love@nrl.navy.mil [Chemistry Division, Code 6113, U.S. Naval Research Laboratory, Washington, DC 20375 (United States); Swider-Lyons, Karen E. [Chemistry Division, Code 6113, U.S. Naval Research Laboratory, Washington, DC 20375 (United States); Twigg, Mark E. [Electronics Science and Technology Division, Code 6812, U.S. Naval Research Laboratory, Washington, DC 20375 (United States); Ramaker, David E. [Chemistry Division, Code 6189, U.S. Naval Research laboratory, Washington, DC 20375 (United States)

2013-07-15

The local structure of nanoscale (∼10–40 nm) LiCoO{sub 2} is monitored during electrochemical cycling utilizing in-situ X-ray absorption spectroscopy (XAS). The high surface area of the LiCoO{sub 2} nanoparticles not only enhances capacity fade, but also provides a large signal from the particle surface relative to the bulk. Changes in the nanoscale LiCoO{sub 2} metal-oxide bond lengths, structural disorder, and chemical state are tracked during cycling by adapting the delta mu (Δμ) technique in complement with comprehensive extended X-ray absorption fine structure (EXAFS) modeling. For the first time, we use a Δμ EXAFS method, and by comparison of the difference EXAFS spectra, extrapolate significant coordination changes and reduction of cobalt species with cycling. This combined approach suggests Li–Co site exchange at the surface of the nanoscale LiCoO{sub 2} as a likely factor in the capacity fade and irreversible losses in practical, microscale LiCoO{sub 2}. - Graphical abstract: Electrochemical cycling of Li-ion batteries has strong impact on the structure and integrity of the cathode active material particularly near the surface/electrolyte interface. In developing a new method, we have used in-situ X-ray absorption spectroscopy during electrochemical cycling of nanoscale LiCoO{sub 2} to track changes during charge and discharge and between subsequent cycles. Using difference spectra, several small changes in Co-O bond length, Co-O and Co-Co coordination, and site exchange between Co and Li sites can be tracked. These methods show promise as a new technique to better understand processes which lead to capacity fade and loss in Li-ion batteries. - Highlights: • A new method is developed to understand capacity fade in Li-ion battery cathodes. • Structural changes are tracked during Li intercalation/deintercalation of LiCoO{sub 2}. • Surface structural changes are emphasized using nanoscale-LiCoO{sub 2} and difference spectra. • Full multiple

Potential role of phosphate buffering capacity of soils in fertilizer management strategies fitted to environmental goals

NARCIS (Netherlands)

Ehlert, P.A.I.; Morel, C.; Fotyma, M.; Destain, J.P.

2003-01-01

Sorption behavior and buffering of phosphorus (P) are important, both from an agricultural and an environmental point of view. The objectives of this study were to investigate: (1) the kinetics of the transfer of P from soil to soil solution and assessing P buffering capacity of soils (PBC), as a

Effects of the pH/pCO2 control method in the growth medium of phytoplankton

Science.gov (United States)

Shi, D.; Xu, Y.; Morel, F. M. M.

2009-02-01

To study the effects of ocean acidification on the physiology of phytoplankton requires that the key chemical parameters of the growth medium, pCO2, pH and Ω (the saturation state of calcium carbonate) be carefully controlled. This is made difficult by the interdependence of these parameters. Moreover, in growing batch cultures of phytoplankton, the fixation of CO2, the uptake of nutrients and, for coccolithophores, the precipitation of calcite all change the inorganic carbon and acid-base chemistry of the medium. For example, absent pH-buffering or CO2 bubbling, a sizeable decrease in pCO2 occurs at a biomass concentration as low as 50 μM C in non-calcifying cultures. Even in cultures where pCO2 or pH is maintained constant, other chemical parameters change substantially at high cell densities. The quantification of these changes is facilitated by the use of buffer capacities. Experimentally we observe that all methods of adjustment of pCO2/pH can be used, the choice of one or the other depending on the specifics of the experiments. The mechanical effect of bubbling of cultures seems to induce more variable results than other methods of pCO2/pH control. While highly convenient, the addition of pH buffers to the medium induces changes in trace metal availability and cannot be used under trace metal-limiting conditions.

Enhancing Nitrogen Availability, Ammonium Adsorption-Desorption, and Soil pH Buffering Capacity using Composted Paddy Husk

Science.gov (United States)

Latifah, O.; Ahmed, O. H.; Abdul Majid, N. M.

2017-12-01

Form of nitrogen present in soils is one of the factors that affect nitrogen loss. Nitrate is mobile in soils because it does not absorb on soil colloids, thus, causing it to be leached by rainfall to deeper soil layers or into the ground water. On the other hand, temporary retention and timely release of ammonium in soils regulate nitrogen availability for crops. In this study, composted paddy husk was used in studies of soil leaching, buffering capacity, and ammonium adsorption and desorption to determine the: (i) availability of exchangeable ammonium, available nitrate, and total nitrogen in an acid soil after leaching the soil for 30 days, (ii) soil buffering capacity, and (iii) ability of the composted paddy husk to adsorb and desorb ammonium from urea. Leaching of ammonium and nitrate were lower in all treatments with urea and composted paddy husk compared with urea alone. Higher retention of soil exchangeable ammonium, available nitrate, and total nitrogen of the soils with composted paddy husk were due to the high buffering capacity and cation exchange capacity of the amendment to adsorb ammonium thus, improving nitrogen availability through temporary retention on the exchange sites of the humic acids of the composted paddy husk. Nitrogen availability can be enhanced if urea is amended with composted paddy husk.

Buffer layer annealing effects on the magnetization reversal process in Pd/Co/Pd systems

International Nuclear Information System (INIS)

Fassatoui, A.; Belhi, R.; Vogel, J.; Abdelmoula, K.

2016-01-01

We have investigated the effect of annealing the buffer layer on the magnetization reversal behavior in Pd/Co/Pd thin films using magneto-optical Kerr microscopy. It was found that annealing the buffer layer at 150 °C for 1 h decreases the coercivity and increases the saturation magnetization and the effective magnetic anisotropy constant. This study also shows that the annealing induces a change of the magnetization reversal from a mixed nucleation and domain wall propagation process to one dominated by domain wall propagation. This result demonstrates that the main effect of annealing the buffer layer is to decrease the domain wall pinning in the Co layer, favoring the domain wall propagation mode. - Highlights: • The buffer layer surface morphology changes upon annealing of the buffer layer. • The coercivity decreases while the saturation magnetization and the effective anisotropy increase with the annealing of the buffer layer. • The reversal process changes from a mixed nucleation and domain wall propagation process to one dominated by domain wall propagation when annealing the buffer layer.

Avaliação da capacidade tamponante - um experimento participativo Buffer capacity evaluating - a collaborative experiment

Directory of Open Access Journals (Sweden)

César Ricardo Silva

2000-06-01

Full Text Available The aim of this work is to show an experiment from which students can learn some of the main characteristics of buffer solutions. A mixture of some acid-base indicators, named as Yamada's indicator, can be used to estimate pH values in an acid-base titration of a buffer, with good approximation. In the experiment it is also possible to verify the relationship between the buffer capacity and the concentrations and the molar ratio of the components of a NH3 / NH4+ buffer solution. The shortage of experiments associated with the relative small importance given to many aspects of buffer solutions, is now explored with simplicity. In the proposed experiments, students prepare buffer solutions by themselves, calculate the pH, understand how acid-base indicators act and learn how buffer solutions work through graph constructed by sharing experimental data.

Preliminary findings on the correlation of saliva pH, buffering capacity, flow, Consistency and Streptococcus mutans in relation to cigarette smoking.

Science.gov (United States)

Voelker, Marsha A; Simmer-Beck, Melanie; Cole, Molly; Keeven, Erin; Tira, Daniel

2013-02-01

The purpose of this preliminary study was to examine the relationship of caries risk, salivary buffering capacity, salivary pH, salivary quality (flow, consistency) and levels of Streptococcus mutans in relation to cigarette smoking. This clinical trial consisted of 53 volunteer patients receiving care in a university based dental hygiene clinic. Participants completed a questionnaire specific to their social history in regards to tobacco use, oral health and dietary history. Measurements of unstimulated saliva were collected followed by collection of stimulated saliva samples. These samples were used to measure salivary pH, buffering capacity and Streptococcus mutans levels. The subject's smoking status was significantly associated with caries risk (p= 0.001), with 25% of the variability of caries risk attributed to smoking. The smoking status was significantly associated with buffering capacity (p=0.025), with 9% of the variability of buffering status attributed to the smoking. Associations between smoking status and salivary pH were not statistically significant. The subject's caries risk was significantly associated with buffering capacity (p= 0.001), with 25% of the variability of caries risk attributed to the buffering capacity. The subject's caries risk was significantly associated with salivary pH (p= 0.031), with 9% of the variability of caries risk attributed to the salivary pH. The Streptococcus mutans test showed no statistical significance (p>0.05) possibly due to the number and low variance in the subjects. A relationship between caries risk and smoking, buffering capacity and smoking, and stimulated salivary pH and smoking were concluded. No significance difference (p>0.05) between caries risk and salivary pH, salivary quality and smoking, S. mutans and smoking were noted from the preliminary results.

Evaluation of the CO2 sequestration capacity for coal fly ash using a flow-through column reactor under ambient conditions

International Nuclear Information System (INIS)

Jo, Ho Young; Ahn, Joon-Hoon; Jo, Hwanju

2012-01-01

Highlights: ► A conceptual in-situ mineral carbonation method using a coal ash pond is proposed. ► CO 2 uptake occurred by carbonation reaction of CO 2 with Ca 2+ ions from coal fly ash. ► The CO 2 sequestration capacity was affected by the solid dosage. ► Seawater can be used as a solvent for mineral carbonation of coal fly ash. - Abstract: An in-situ CO 2 sequestration method using coal ash ponds located in coastal regions is proposed. The CO 2 sequestration capacity of coal fly ash (CFA) by mineral carbonation was evaluated in a flow-through column reactor under various conditions (solid dosage: 100–330 g/L, CO 2 flow rate: 20–80 mL/min, solvent type: deionized (DI) water, 1 M NH 4 Cl solution, and seawater). The CO 2 sequestration tests were conducted on CFA slurries using flow-through column reactors to simulate more realistic flow-through conditions. The CO 2 sequestration capacity increased when the solid dosage was increased, whereas it was affected insignificantly by the CO 2 flow rate. A 1 M NH 4 Cl solution was the most effective solvent, but it was not significantly different from DI water or seawater. The CO 2 sequestration capacity of CFA under the flow-through conditions was approximately 0.019 g CO 2 /g CFA under the test conditions (solid dosage: 333 g/L, CO 2 flow rate: 40 mL/min, and solvent: seawater).

Computation of Buffer Capacities for Throughput Constrained and Data Dependent Inter-Task Communication

NARCIS (Netherlands)

Wiggers, M.H.; Bekooij, Marco Jan Gerrit; Bekooij, Marco J.G.; Smit, Gerardus Johannes Maria

2008-01-01

Streaming applications are often implemented as task graphs. Currently, techniques exist to derive buffer capacities that guarantee satisfaction of a throughput constraint for task graphs in which the inter-task communication is data-independent, i.e. the amount of data produced and consumed is

Método para avaliação clínica da capacidade tamponante salivar A method for the clinical evaluation of salivary buffer capacity

Directory of Open Access Journals (Sweden)

Augusto César Cropanese SPADARO

1998-07-01

Full Text Available O presente estudo teve por objetivo o desenvolvimento e a padronização de um método colorimétrico para avaliar a capacidade tamponante salivar média de nossa população. As amostras de saliva estimulada foram tituladas sem eliminação do CO2. Estudos foram realizados para verificar a influência da perda de CO2 das amostras durante o período necessário para a realização das titulações e para a padronização do tempo de leitura do pH. A partir das titulações realizadas nas amostras de saliva de 206 indivíduos de ambos os sexos na faixa etária de 5 a 50 anos, na proporção de 0,77:1:0,44, respectivamente para crianças, jovens e adultos, foram feitas as distribuições de freqüências dos casos, a determinação média do pH inicial, do pKa, microequivalentes relativos ao final da titulação, pH final da titulação e uma estimativa da porcentagem da saliva titulada em pH 5. Com base nestas variáveis foi estabelecida uma classificação dos indivíduos quanto à capacidade tamponante. Análise dos resultados utilizando-se 11, 12 ou 13 microequivalentes de H+/ml indicam que o valor de 11 microequivalentes/ml de saliva é o mais apropriado para a avaliação da capacidade tamponante salivar em nossa população.The present study aimed to develop and standardize a colorimetric method for assessing salivary buffer capacity adapted to the features of the Brazilian population. Samples of stimulated saliva were titrated without CO2 elimination. The assessment was carried out to study the influence of the loss of CO2 from the samples during the few minutes necessary for titration, and to standardize the instants for measuring pH. Saliva samples were titrated from 206 individuals from both genders, between 5 and 50 years of age, and in a proportion of 0.77 : 1 : 0.44, respectively of children, youngsters, and adults. Case frequency distribution; determination of average values of initial pH, pKa, µ equivalents related to titration

Effects of rehydration and food consumption on salivary flow, pH and buffering capacity in young adult volunteers during ergometer exercise.

Science.gov (United States)

Tanabe, Mai; Takahashi, Toshiyuki; Shimoyama, Kazuhiro; Toyoshima, Yukako; Ueno, Toshiaki

2013-10-28

The aim of this study was to investigate the influences of rehydration and food consumption on salivary flow, pH, and buffering capacity during bicycle ergometer exercise in participants. Ten healthy volunteers exercised on a bicycle ergometer at 80% of their maximal heart rate. These sessions lasted for two periods of 20 min separated by 5-min rest intervals. Volunteers were subjected to one of the following conditions: (1) no water (mineral water) or food consumption, (2) only water for rehydration, (3) water and food consumption, (4) a sports drink only for rehydration, and (5) rehydration with a sports drink and food. Statistical significance was assessed using one-way analysis of variance and Dunnett's test (p salivary pH decreased significantly during and after exercise in conditions 4 and 5. The salivary buffering capacity decreased significantly during exercise and/or after the exercise in conditions 1, 3, 4, and 5. The results showed that salivary pH and buffering capacity decreased greatly depending on the combination of a sports drink and food.

Capacity expansion analysis of UGSs rebuilt from low-permeability fractured gas reservoirs with CO2 as cushion gas

Directory of Open Access Journals (Sweden)

Yufei Tan

2016-11-01

Full Text Available The techniques of pressurized mining and hydraulic fracturing are often used to improve gas well productivity at the later development stage of low-permeability carbonate gas reservoirs, but reservoirs are watered out and a great number of micro fractures are produced. Therefore, one of the key factors for underground gas storages (UGS rebuilt from low-permeability fractured gas reservoirs with CO2 as the cushion gas is how to expand storage capacity effectively by injecting CO2 to displace water and to develop control strategies for the stable migration of gas–water interface. In this paper, a mathematical model was established to simulate the gas–water flow when CO2 was injected into dual porosity reservoirs to displace water. Then, the gas–water interface migration rules while CO2 was injected in the peripheral gas wells for water displacement were analyzed with one domestic UGS rebuilt from fractured gas reservoirs as the research object. And finally, discussion was made on how CO2 dissolution, bottom hole flowing pressure (BHFP, CO2 injection rate and micro fracture parameters affect the stability of gas–water interface in the process of storage capacity expansion. It is shown that the speed of capacity expansion reaches the maximum value at the fifth cycle and then decreases gradually when UGS capacity is expanded in the pattern of more injection and less withdrawal. Gas–water interface during UGS capacity expansion is made stable due to that the solubility of CO2 in water varies with the reservoir pressure. When the UGS capacity is expanded at constant BHFP and the flow rate, the expansion speed can be increased effectively by increasing the BHFP and the injection flow rate of gas wells in the central areas appropriately. In the reservoir areas with high permeability and fracture-matrix permeability ratio, the injection flow rate should be reduced properly to prevent gas–water interface fingering caused by a high-speed flow

Effects of O{sub 2} and SO{sub 2} on the Capture Capacity of a Primary-Amine Based Polymeric CO{sub 2} Sorbent

Energy Technology Data Exchange (ETDEWEB)

Hallenbeck, Alexander P; Kitchin, John R

2013-08-01

Post combustion CO{sub 2} capture is most commonly carried out using an amine solution that results in a high parasitic energy cost in the stripper unit due to the need to heat the water which comprises a majority of the amine solution. It is also well known that amine solvents suffer from stability issues due to amine leaching and poisoning by flue gas impurities. Solid sorbents provide an alternative to solvent systems that would potentially reduce the energy penalty of carbon capture. However, the cost of using a particular sorbent is greatly affected by the usable lifetime of the sorbent. This work investigated the stability of a primary amine-functionalized ion exchange resin in the presence of O{sub 2} and SO{sub 2}, both of which are constituents of flue gas that have been shown to cause degradation of various amines in solvent processes. The CO{sub 2} capture capacity was measured over multiple capture cycles under continuous exposure to two simulated flue gas streams, one containing 12 vol% CO{sub 2}, 4% O{sub 2}, 84% N{sub 2}, and the other containing 12.5 vol% CO{sub 2}, 4% O{sub 2}, 431 ppm SO{sub 2}, balance N{sub 2} using a custom-built packed bed reactor. The resin maintained its CO{sub 2} capture capacity of 1.31 mol/kg over 17 capture cycles in the presence of O{sub 2} without SO{sub 2}. However, the CO{sub 2} capture capacity of the resin decreased rapidly under exposure to SO{sub 2} by an amount of 1.3 mol/kg over 9 capture cycles. Elemental analysis revealed the resin adsorbed 1.0 mol/kg of SO{sub 2}. Thermal regeneration was determined to not be possible. The poisoned resin was, however, partially regenerated with exposure to 1.5M NaOH for 3 days resulting in a 43% removal of sulfur, determined through elemental analysis, and a 35% recovery of CO{sub 2} capture capacity. Evidence was also found for amine loss upon prolonged (7 days) continuous exposure to high temperatures (120 C) in air. It is concluded that desulfurization of the flue gas

The Baltic Basin: structure, properties of reservoir rocks, and capacity for geological storage of CO2

Directory of Open Access Journals (Sweden)

Vaher, Rein

2009-12-01

Full Text Available Baltic countries are located in the limits of the Baltic sedimentary basin, a 700 km long and 500 km wide synclinal structure. The axis of the syneclise plunges to the southwest. In Poland the Precambrian basement occurs at a depth of 5 km. The Baltic Basin includes the Neoproterozoic Ediacaran (Vendian at the base and all Phanerozoic systems. Two aquifers, the lower Devonian and Cambrian reservoirs, meet the basic requirements for CO2 storage. The porosity and permeability of sandstone decrease with depth. The average porosity of Cambrian sandstone at depths of 80–800, 800–1800, and 1800–2300 m is 18.6, 14.2, and 5.5%, respectively. The average permeability is, respectively, 311, 251, and 12 mD. Devonian sandstone has an average porosity of 26% and permeability in the range of 0.5–2 D. Prospective Cambrian structural traps occur only in Latvia. The 16 largest ones have CO2 storage capacity in the range of 2–74 Mt, with total capacity exceeding 400 Mt. The structural trapping is not an option for Lithuania as the uplifts there are too small. Another option is utilization of CO2 for enhanced oil recovery (EOR. The estimated total EOR net volume of CO2 (part of CO2 remaining in the formation in Lithuania is 5.6 Mt. Solubility and mineral trapping are a long-term option. The calculated total solubility trapping capacity of the Cambrian reservoir is as high as 11 Gt of CO2 within the area of the supercritical state of carbon dioxide.

Thermal and Carbon Dioxide Inactivation of Alkaline Phosphatase in Buffer and Milk

Directory of Open Access Journals (Sweden)

Osman Erkmen

2004-01-01

Full Text Available The effects of temperature and CO2 treatment on the inactivation of alkaline phosphatase (ALP were studied. The thermal stability of ALP was found to be significantly (P< 0.05 different in glycine/NaOH buffer, pasteurized milk and raw milk. ALP was completely inactivated in the buffer at 60, 70 and 80 °C but approximately 12 % of activity was present at 50 °C after 55 min of treatment. The time required for complete inactivation of the enzyme in the buffer was reduced from 50 to 4 min as temperature increased from 60 to 80 °C. Complete inactivation of the enzyme in pasteurized milk was achieved at 70 and 80 °C but 28 and 15 % of ALP activity was still present at 50 and 60 °C after 120 min of treatment. Inactivation time for raw milk was reduced nearly 18-fold by increasing temperature from 50 to 70 °C. ALP in the buffer exposed to CO2 (under atmospheric pressure treatment at different temperatures showed a decrease in enzyme activity. Inactivation was found to be higher as the temperature increased from 20 to 50 °C. At the end of a 30-min treatment, residual ALP activity was found to be 84 and 19 % at 20 and 50 °C, respectively. Faster drop in pH and enzyme activity occurred within 5 min. The change in pH and enzyme activity dependant on CO2 treatment was not observed in raw milk mainly due to strong buffering capacity of milk.

The effect of pH, buffer capacity and ionic strength on quetiapine fumarate release from matrix tablets prepared using two different polymeric blends.

Science.gov (United States)

Hamed, Rania; AlJanabi, Reem; Sunoqrot, Suhair; Abbas, Aiman

2017-08-01

The objective of this study was to investigate the effect of the different physiological parameters of the gastrointestinal (GI) fluid (pH, buffer capacity, and ionic strength) on the in vitro release of the weakly basic BCS class II drug quetiapine fumarate (QF) from two once-a-day matrix tablet formulations (F1 and F2) developed as potential generic equivalents to Seroquel ® XR. F1 tablets were prepared using blends of high and low viscosity grades of hydroxypropyl methylcellulose (HPMC K4M and K100LV, respectively), while F2 tablets were prepared from HPMC K4M and PEGylated glyceryl behenate (Compritol ® HD5 ATO). The two formulations attained release profiles of QF over 24 h similar to that of Seroquel ® XR using the dissolution medium published by the Food and Drug Administration (FDA). A series of solubility and in vitro dissolution studies was then carried out using media that simulate the gastric and intestinal fluids and cover the physiological pH, buffer capacity and ionic strength range of the GIT. Solubility studies revealed that QF exhibits a typical weak base pH-dependent solubility profile and that the solubility of QF increases with increasing the buffer capacity and ionic strength of the media. The release profiles of QF from F1, F2 and Seroquel ® XR tablets were found to be influenced by the pH, buffer capacity and ionic strength of the dissolution media to varying degrees. Results highlight the importance of studying the physiological variables along the GIT in designing controlled release formulations for more predictive in vitro-in vivo correlations.

A facile route to synthesize multiporous MnCo2O4 and CoMn2O4 spinel quasi-hollow spheres with improved lithium storage properties

Science.gov (United States)

Li, Jingfa; Xiong, Shenglin; Li, Xiaowei; Qian, Yitai

2013-02-01

A facile and general way for the synthesis of porous and hollow complex oxides is highly desirable owing to their significant applications for energy storage and other fields. In this contribution, uniform Mn0.33Co0.67CO3 and Co0.33Mn0.67CO3 microspheres are firstly fabricated solvothermally just by tuning the molar ratio of Mn and Co. Subsequently, the growth of multiporous MnCo2O4 and CoMn2O4 quasi-hollow microspheres by topotactic chemical transformation from the corresponding precursors are realized through a non-equilibrium heat treatment process. Topotactic conversion further demonstrated that the much larger CoMn2O4 pores than those of MnCo2O4 are possibly due to the longer transfer distance of ions. When evaluated as anode materials for LIBs (lithium ion batteries), after 25 cycles at a current density of 200 mA g-1, the resultant MnCo2O4 and CoMn2O4 quasi-hollow microspheres possessed reversible capacities of 755 and 706 mA h g-1, respectively. In particular, the MnCo2O4 samples could deliver a reversible capacity as high as 610 mA h g-1 even at a higher current density of 400 mA g-1 with excellent electrochemical stability after 100 cycles of testing, indicating its potential application in LIBs. We believe that such good performance results from the appropriate pore size and quasi-hollow nature of MnCo2O4 microspheres, which can effectively buffer the large volume variation of anodes based on the conversion reaction during Li+ insertion/extraction. The present strategy is simple but very effective, and due to its versatility, it can be extended to other binary, even ternary complex metal oxides with high-performance in LIBs.A facile and general way for the synthesis of porous and hollow complex oxides is highly desirable owing to their significant applications for energy storage and other fields. In this contribution, uniform Mn0.33Co0.67CO3 and Co0.33Mn0.67CO3 microspheres are firstly fabricated solvothermally just by tuning the molar ratio of Mn and Co

Nanoscale Chemical Processes Affecting Storage Capacities and Seals during Geologic CO2 Sequestration.

Science.gov (United States)

Jun, Young-Shin; Zhang, Lijie; Min, Yujia; Li, Qingyun

2017-07-18

Geologic CO 2 sequestration (GCS) is a promising strategy to mitigate anthropogenic CO 2 emission to the atmosphere. Suitable geologic storage sites should have a porous reservoir rock zone where injected CO 2 can displace brine and be stored in pores, and an impermeable zone on top of reservoir rocks to hinder upward movement of buoyant CO 2 . The injection wells (steel casings encased in concrete) pass through these geologic zones and lead CO 2 to the desired zones. In subsurface environments, CO 2 is reactive as both a supercritical (sc) phase and aqueous (aq) species. Its nanoscale chemical reactions with geomedia and wellbores are closely related to the safety and efficiency of CO 2 storage. For example, the injection pressure is determined by the wettability and permeability of geomedia, which can be sensitive to nanoscale mineral-fluid interactions; the sealing safety of the injection sites is affected by the opening and closing of fractures in caprocks and the alteration of wellbore integrity caused by nanoscale chemical reactions; and the time scale for CO 2 mineralization is also largely dependent on the chemical reactivities of the reservoir rocks. Therefore, nanoscale chemical processes can influence the hydrogeological and mechanical properties of geomedia, such as their wettability, permeability, mechanical strength, and fracturing. This Account reviews our group's work on nanoscale chemical reactions and their qualitative impacts on seal integrity and storage capacity at GCS sites from four points of view. First, studies on dissolution of feldspar, an important reservoir rock constituent, and subsequent secondary mineral precipitation are discussed, focusing on the effects of feldspar crystallography, cations, and sulfate anions. Second, interfacial reactions between caprock and brine are introduced using model clay minerals, with focuses on the effects of water chemistries (salinity and organic ligands) and water content on mineral dissolution and

Optimization of CO2 adsorption capacity and cyclical adsorption/desorption on tetraethylenepentamine-supported surface-modified hydrotalcite.

Science.gov (United States)

Thouchprasitchai, Nutthavich; Pintuyothin, Nuthapol; Pongstabodee, Sangobtip

2018-03-01

The objective of this research was to investigate CO 2 adsorption capacity of tetraethylenepentamine-functionalized basic-modified calcined hydrotalcite (TEPA/b-cHT) sorbents at atmospheric pressure formed under varying TEPA loading levels, temperatures, sorbent weight to total gaseous flow rate (W/F) ratios and CO 2 concentrations in the influent gas. The TEPA/b-cHT sorbents were characterized by means of X-ray diffraction (XRD), Fourier transform infrared spectrometry (FT-IR), thermal gravimetric analysis (TGA), Brunauer-Emmet-Teller (BET) analysis of nitrogen (N 2 ) adsorption/desorption and carbon-hydrogen-nitrogen (CHN) elemental analysis. Moreover, a full 2 4 factorial design with three central points at a 95% confidence interval was used to screen important factor(s) on the CO 2 adsorption capacity. It revealed that 85.0% variation in the capacity came from the influence of four main factors and the 15.0% one was from their interactions. A face-centered central composite design response surface method (FCCCD-RSM) was then employed to optimize the condition, the maximal capacity of 5.5-6.1mmol/g was achieved when operating with a TEPA loading level of 39%-49% (W/W), temperature of 76-90°C, W/F ratio of 1.7-2.60(g·sec)/cm 3 and CO 2 concentration of 27%-41% (V/V). The model fitted sufficiently the experimental data with an error range of ±1.5%. From cyclical adsorption/desorption and selectivity at the optimal condition, the 40%TEPA/b-cHT still expressed its effective performance after eight cycles. Copyright © 2017. Published by Elsevier B.V.

Efficient Buffer Capacity and Scheduler Setting Computation for Soft Real-Time Stream Processing Applications

NARCIS (Netherlands)

Bekooij, Marco; Bekooij, Marco Jan Gerrit; Wiggers, M.H.; van Meerbergen, Jef

2007-01-01

Soft real-time applications that process data streams can often be intuitively described as dataflow process networks. In this paper we present a novel analysis technique to compute conservative estimates of the required buffer capacities in such process networks. With the same analysis technique

Salivary Parameters (Salivary Flow, pH and Buffering Capacity) in Stimulated Saliva of Mexican Elders 60 Years Old and Older.

Science.gov (United States)

Islas-Granillo, H; Borges-Yañez, S A; Medina-Solís, C E; Galan-Vidal, C A; Navarrete-Hernández, J J; Escoffié-Ramirez, M; Maupomé, G

2014-12-01

To compare a limited array of chewing-stimulated saliva features (salivary flow, pH and buffer capacity) in a sample of elderly Mexicans with clinical, sociodemographic and socio-economic variables. A cross-sectional study was carried out in 139 adults, 60 years old and older, from two retirement homes and a senior day care centre in the city of Pachuca, Mexico. Sociodemographic, socio-economic and behavioural variables were collected through a questionnaire. A trained and standardized examiner obtained the oral clinical variables. Chewing-stimulated saliva (paraffin method) was collected and the salivary flow rate, pH and buffer capacity were measured. The analysis was performed using non-parametric tests in Stata 9.0. Mean age was 79.1 ± 9.8 years. Most of the subjects included were women (69.1%). Mean chewing-stimulated salivary flow was 0.75 ± 0.80 mL/minute, and the pH and buffer capacity were 7.88 ± 0.83 and 4.20 ± 1.24, respectively. Mean chewing-stimulated salivary flow varied (p pH varied across the type of retirement home (p salivary features (salivary flow rate, pH and buffer capacity) and outline the variability of those features across selected sociodemographic, socio-economic and behavioural variables in a group of Mexican elders.

Evaluation of the CO{sub 2} sequestration capacity for coal fly ash using a flow-through column reactor under ambient conditions

Energy Technology Data Exchange (ETDEWEB)

Jo, Ho Young, E-mail: hyjo@korea.ac.kr [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 136-713 (Korea, Republic of); Ahn, Joon-Hoon; Jo, Hwanju [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 136-713 (Korea, Republic of)

2012-11-30

Highlights: Black-Right-Pointing-Pointer A conceptual in-situ mineral carbonation method using a coal ash pond is proposed. Black-Right-Pointing-Pointer CO{sub 2} uptake occurred by carbonation reaction of CO{sub 2} with Ca{sup 2+} ions from coal fly ash. Black-Right-Pointing-Pointer The CO{sub 2} sequestration capacity was affected by the solid dosage. Black-Right-Pointing-Pointer Seawater can be used as a solvent for mineral carbonation of coal fly ash. - Abstract: An in-situ CO{sub 2} sequestration method using coal ash ponds located in coastal regions is proposed. The CO{sub 2} sequestration capacity of coal fly ash (CFA) by mineral carbonation was evaluated in a flow-through column reactor under various conditions (solid dosage: 100-330 g/L, CO{sub 2} flow rate: 20-80 mL/min, solvent type: deionized (DI) water, 1 M NH{sub 4}Cl solution, and seawater). The CO{sub 2} sequestration tests were conducted on CFA slurries using flow-through column reactors to simulate more realistic flow-through conditions. The CO{sub 2} sequestration capacity increased when the solid dosage was increased, whereas it was affected insignificantly by the CO{sub 2} flow rate. A 1 M NH{sub 4}Cl solution was the most effective solvent, but it was not significantly different from DI water or seawater. The CO{sub 2} sequestration capacity of CFA under the flow-through conditions was approximately 0.019 g CO{sub 2}/g CFA under the test conditions (solid dosage: 333 g/L, CO{sub 2} flow rate: 40 mL/min, and solvent: seawater).

Estimating values for the moisture source load and buffering capacities from indoor climate measurements

NARCIS (Netherlands)

Schijndel, van A.W.M.

2008-01-01

The objective of this study is to investigate the potential for estimating values for the total size of human induced moisture source load and the total buffering (moisture storage) capacity of the interior objects with the use of relatively simple measurements and the use of heat, air, and moisture

Determination of Henry's constant, the dissociation constant, and the buffer capacity of the bicarbonate system in ruminal fluid.

Science.gov (United States)

Hille, Katharina T; Hetz, Stefan K; Rosendahl, Julia; Braun, Hannah-Sophie; Pieper, Robert; Stumpff, Friederike

2016-01-01

Despite the clinical importance of ruminal acidosis, ruminal buffering continues to be poorly understood. In particular, the constants for the dissociation of H2CO3 and the solubility of CO2 (Henry's constant) have never been stringently determined for ruminal fluid. The pH was measured in parallel directly in the rumen and the reticulum in vivo, and in samples obtained via aspiration from 10 fistulated cows on hay- or concentrate-based diets. The equilibrium constants of the bicarbonate system were measured at 38°C both using the Astrup technique and a newly developed method with titration at 2 levels of partial pressure of CO2 (pCO2; 4.75 and 94.98 kPa), yielding mean values of 0.234 ± 0.005 mmol ∙ L(-1) ∙ kPa(-1) and 6.11 ± 0.02 for Henry's constant and the dissociation constant, respectively (n/n = 31/10). Both reticular pH and the pH of samples measured after removal were more alkalic than those measured in vivo in the rumen (by ΔpH = 0.87 ± 0.04 and 0.26 ± 0.04). The amount of acid or base required to shift the pH of ruminal samples to 6.4 or 5.8 (base excess) differed between the 2 feeding groups. Experimental results are compared with the mathematical predictions of an open 2-buffer Henderson-Hasselbalch equilibrium model. Because pCO2 has pronounced effects on ruminal pH and can decrease rapidly in samples removed from the rumen, introduction of a generally accepted protocol for determining the acid-base status of ruminal fluid with standard levels of pCO2 and measurement of base excess in addition to pH should be considered. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Investigation of a cooled electroionization CO laser. I - Lasing using pure carbon monoxide. II - Lasing using mixtures of CO with buffer gases

Energy Technology Data Exchange (ETDEWEB)

Basov, N G; Danilychev, V A; Ionin, A A; Kazakevich, V S; Kovsh, I B; Poletaev, N L

1979-06-01

An experimental study has been performed to determine the threshold, energy, temporal and spectral characteristics of a cooled electroionization pulsed laser using pure CO. It is shown that the efficiency of the laser using pure CO does not exceed 10%. A reduction of CO concentration in a mixture with a nitrogen buffer to 2.5% at the fixed excitation pulse duration of 100 microsec results in an increase of radiation pulse duration from 100 microsec (pure CO) to 3 ms. The present results are compared to the theoretical and experimental results of other studies.

Assessment of Factors Influencing Effective CO₂ Storage Capacity and Injectivity in Eastern Gas Shales

Energy Technology Data Exchange (ETDEWEB)

Godec, Michael [Advanced Resources International, Inc., Arlington, VA (United States)

2013-06-30

Building upon advances in technology, production of natural gas from organic-rich shales is rapidly developing as a major hydrocarbon supply option in North America and around the world. The same technology advances that have facilitated this revolution - dense well spacing, horizontal drilling, and hydraulic fracturing - may help to facilitate enhanced gas recovery (EGR) and carbon dioxide (CO₂) storage in these formations. The potential storage of CO₂ in shales is attracting increasing interest, especially in Appalachian Basin states that have extensive shale deposits, but limited CO₂ storage capacity in conventional reservoirs. The goal of this cooperative research project was to build upon previous and on-going work to assess key factors that could influence effective EGR, CO₂ storage capacity, and injectivity in selected Eastern gas shales, including the Devonian Marcellus Shale, the Devonian Ohio Shale, the Ordovician Utica and Point Pleasant shale and equivalent formations, and the late Devonian-age Antrim Shale. The project had the following objectives: (1) Analyze and synthesize geologic information and reservoir data through collaboration with selected State geological surveys, universities, and oil and gas operators; (2) improve reservoir models to perform reservoir simulations to better understand the shale characteristics that impact EGR, storage capacity and CO₂ injectivity in the targeted shales; (3) Analyze results of a targeted, highly monitored, small-scale CO₂ injection test and incorporate into ongoing characterization and simulation work; (4) Test and model a smart particle early warning concept that can potentially be used to inject water with uniquely labeled particles before the start of CO₂ injection; (5) Identify and evaluate potential constraints to economic CO₂ storage in gas shales, and propose development approaches that overcome these constraints

Buffer Sizing in 802.11 Wireless Mesh Networks

KAUST Repository

Jamshaid, Kamran; Shihada, Basem; Xia, Li; Levis, Philip

2011-01-01

We analyze the problem of buffer sizing for TCP flows in 802.11-based Wireless Mesh Networks. Our objective is to maintain high network utilization while providing low queueing delays. The problem is complicated by the time-varying capacity of the wireless channel as well as the random access mechanism of 802.11 MAC protocol. While arbitrarily large buffers can maintain high network utilization, this results in large queueing delays. Such delays may affect TCP stability characteristics, and also increase queueing delays for other flows (including real-time flows) sharing the buffer. In this paper we propose sizing link buffers collectively for a set of nodes within mutual interference range called the 'collision domain'. We aim to provide a buffer just large enough to saturate the available capacity of the bottleneck collision domain that limits the carrying capacity of the network. This neighborhood buffer is distributed over multiple nodes that constitute the network bottleneck; a transmission by any of these nodes fully utilizes the available spectral resource for the duration of the transmission. We show that sizing routing buffers collectively for this bottleneck allows us to have small buffers (as low as 2 - 3 packets) at individual nodes without any significant loss in network utilization. We propose heuristics to determine these buffer sizes in WMNs. Our results show that we can reduce the end-to-end delays by 6× to 10× at the cost of losing roughly 5% of the network capacity achievable with large buffers.

Buffer Sizing in 802.11 Wireless Mesh Networks

KAUST Repository

Jamshaid, Kamran

2011-10-01

We analyze the problem of buffer sizing for TCP flows in 802.11-based Wireless Mesh Networks. Our objective is to maintain high network utilization while providing low queueing delays. The problem is complicated by the time-varying capacity of the wireless channel as well as the random access mechanism of 802.11 MAC protocol. While arbitrarily large buffers can maintain high network utilization, this results in large queueing delays. Such delays may affect TCP stability characteristics, and also increase queueing delays for other flows (including real-time flows) sharing the buffer. In this paper we propose sizing link buffers collectively for a set of nodes within mutual interference range called the \\'collision domain\\'. We aim to provide a buffer just large enough to saturate the available capacity of the bottleneck collision domain that limits the carrying capacity of the network. This neighborhood buffer is distributed over multiple nodes that constitute the network bottleneck; a transmission by any of these nodes fully utilizes the available spectral resource for the duration of the transmission. We show that sizing routing buffers collectively for this bottleneck allows us to have small buffers (as low as 2 - 3 packets) at individual nodes without any significant loss in network utilization. We propose heuristics to determine these buffer sizes in WMNs. Our results show that we can reduce the end-to-end delays by 6× to 10× at the cost of losing roughly 5% of the network capacity achievable with large buffers.

Surface properties of Co-doped BaFe{sub 2}As{sub 2} thin films deposited on MgO with Fe buffer layer and CaF{sub 2} substrates

Energy Technology Data Exchange (ETDEWEB)

Sobota, R. [Department of Experimental Physics, FMPI, Comenius University, 842 48 Bratislava (Slovakia); Plecenik, T., E-mail: tomas.plecenik@fmph.uniba.sk [Department of Experimental Physics, FMPI, Comenius University, 842 48 Bratislava (Slovakia); Gregor, M.; Truchly, M.; Satrapinskyy, L.; Vidis, M.; Secianska, K. [Department of Experimental Physics, FMPI, Comenius University, 842 48 Bratislava (Slovakia); Kurth, F.; Holzapfel, B.; Iida, K. [Institute for Metallic Materials, IFW Dresden, PO Box 270116, D-01171 Dresden (Germany); Kus, P.; Plecenik, A. [Department of Experimental Physics, FMPI, Comenius University, 842 48 Bratislava (Slovakia)

2014-09-01

Highlights: • Surfaces of Co-doped Ba-122 films on various substrates were studied. • Substrate influences topography and surface conductivity distribution of the films. • Surface conductivity of Co-doped Ba-122 is highly inhomogeneous. • Point contact spectroscopy results can be affected by the surface differences. - Abstract: Surface properties of Co-doped BaFe{sub 2}As{sub 2} (Ba-122) thin films prepared by pulsed laser deposition on MgO with Fe buffer layer and CaF{sub 2} substrates were inspected by atomic force microscopy, scanning spreading resistance microscopy, scanning tunneling microscopy, X-ray photoelectron spectroscopy, auger electron spectroscopy/microscopy and point contact spectroscopy (PCS). Selected PCS spectra were fitted by extended 1D BTK model. The measurements were done on as-received as well as ion beam etched surfaces. Our results show that the substrate is considerably influencing the surface properties of the films, particularly the topography and surface conductivity distribution, what can affect results obtained by surface-sensitive techniques like PCS.

Determining the Contribution of Non-Carbonate Alkalinity from Intertidal Salt Marshes to Coastal Buffering Capacity

Science.gov (United States)

Anderson, L. B.; Gonneea, M. E.; Wang, A. Z.; Chu, S. N.

2016-02-01

Coastal ocean acidification varies with high magnitude and frequency due to both natural and anthropogenic factors, and levels of acidity in coastal waters have important consequences for environmental concerns such as local settlement of bivalve populations. Therefore, it is useful to fully evaluate measurements that increase understanding of coastal ocean acidification dynamics. This study focuses on the quantification and characterization of alkalinity, the ability of a specific water parcel to buffer against inputs of acidity. There has been limited research on the magnitude and composition of non-carbonate alkalinity (NCA) generated in coastal environments. Specifically, this study evaluates the contribution of NCA to total alkalinity (TA) in an intertidal salt marsh, assesses NCA dynamics within the marsh, and begins to determine composition of NCA. We demonstrated that it was possible to develop a CO2-free full titration system modeled after Cai et al. (1998) that produced reasonable values for TA and NCA. From initial use of this system, it was evident that NCA was a significant contributor to TA within the Sage Lot Pond salt marsh, and that NCA was dominated by organic/unknown alkalinity. Preliminary observations indicated that NCA variability in the marsh was directly proportional to water flux entering the tidal creek from Sage Lot Pond. The source of higher NCA concentrations in Sage Lot Pond was unknown, but may have been due to organic/unknown alkalinity generated in a different part of the marsh and exported to our specific tidal creek site. Preliminary assessment of NCA composition indicates an acid/base species with a pK value of 6.46. From evaluation of NCA magnitude and relation to water flux, it is reasonable to conclude that NCA generated within salt marshes may be a significant source of buffering capacity to the coastal ocean.

From Metal-Organic Framework to Li2S@C-Co-N Nanoporous Architecture: A High-Capacity Cathode for Lithium-Sulfur Batteries.

Science.gov (United States)

He, Jiarui; Chen, Yuanfu; Lv, Weiqiang; Wen, Kechun; Xu, Chen; Zhang, Wanli; Li, Yanrong; Qin, Wu; He, Weidong

2016-12-27

Owing to the high theoretical specific capacity (1166 mAh g -1 ), lithium sulfide (Li 2 S) has been considered as a promising cathode material for Li-S batteries. However, the polysulfide dissolution and low electronic conductivity of Li 2 S limit its further application in next-generation Li-S batteries. In this report, a nanoporous Li 2 S@C-Co-N cathode is synthesized by liquid infiltration-evaporation of ultrafine Li 2 S nanoparticles into graphitic carbon co-doped with cobalt and nitrogen (C-Co-N) derived from metal-organic frameworks. The obtained Li 2 S@C-Co-N architecture remarkably immobilizes Li 2 S within the cathode structure through physical and chemical molecular interactions. Owing to the synergistic interactions between C-Co-N and Li 2 S nanoparticles, the Li 2 S@C-Co-N composite delivers a reversible capacity of 1155.3 (99.1% of theoretical value) at the initial cycle and 929.6 mAh g -1 after 300 cycles, with nearly 100% Coulombic efficiency and a capacity fading of 0.06% per cycle. It exhibits excellent rate capacities of 950.6, 898.8, and 604.1 mAh g -1 at 1C, 2C, and 4C, respectively. Such a cathode structure is promising for practical applications in high-performance Li-S batteries.

Enhancing mitochondrial calcium buffering capacity reduces aggregation of misfolded SOD1 and motor neuron cell death without extending survival in mouse models of inherited amyotrophic lateral sclerosis.

Science.gov (United States)

Parone, Philippe A; Da Cruz, Sandrine; Han, Joo Seok; McAlonis-Downes, Melissa; Vetto, Anne P; Lee, Sandra K; Tseng, Eva; Cleveland, Don W

2013-03-13

Mitochondria have been proposed as targets for toxicity in amyotrophic lateral sclerosis (ALS), a progressive, fatal adult-onset neurodegenerative disorder characterized by the selective loss of motor neurons. A decrease in the capacity of spinal cord mitochondria to buffer calcium (Ca(2+)) has been observed in mice expressing ALS-linked mutants of SOD1 that develop motor neuron disease with many of the key pathological hallmarks seen in ALS patients. In mice expressing three different ALS-causing SOD1 mutants, we now test the contribution of the loss of mitochondrial Ca(2+)-buffering capacity to disease mechanism(s) by eliminating ubiquitous expression of cyclophilin D, a critical regulator of Ca(2+)-mediated opening of the mitochondrial permeability transition pore that determines mitochondrial Ca(2+) content. A chronic increase in mitochondrial buffering of Ca(2+) in the absence of cyclophilin D was maintained throughout disease course and was associated with improved mitochondrial ATP synthesis, reduced mitochondrial swelling, and retention of normal morphology. This was accompanied by an attenuation of glial activation, reduction in levels of misfolded SOD1 aggregates in the spinal cord, and a significant suppression of motor neuron death throughout disease. Despite this, muscle denervation, motor axon degeneration, and disease progression and survival were unaffected, thereby eliminating mutant SOD1-mediated loss of mitochondrial Ca(2+) buffering capacity, altered mitochondrial morphology, motor neuron death, and misfolded SOD1 aggregates, as primary contributors to disease mechanism for fatal paralysis in these models of familial ALS.

The effect of CO2 and non-CO2-generating buffers on cerebral acidosis after cardiac arrest: A 31P NMR study.

Science.gov (United States)

Rosenberg, J M; Martin, G B; Paradis, N A; Nowak, R M; Walton, D; Appleton, T J; Welch, K M

1989-04-01

There is controversy regarding the use of alkalinizing agents during reperfusion after cardiac arrest. The potential deleterious effects of sodium bicarbonate (bicarb) administration, including paradoxic cerebral acidosis, have led to the search for alternative agents. Tromethamine (tris) is a non-CO2-generating buffer that has been proposed for use during cardiopulmonary resuscitation. The purpose of this experiment was to compare the ability of tris with bicarb to correct brain pH (pH B) during reperfusion after a 12-minute cardiac arrest. Adult mongrel dogs were instrumented and placed in the bore of a Bruker Biospec 1.89 tesla superconducting magnet system. Ventricular fibrillation was induced; after 12 minutes, cardiopulmonary bypass was initiated and maintained for two hours with minimum flows of 80 mL/kg/min. Bicarb (n = 5) or tris (n = 5) were administered to correct arterial pH as rapidly as possible. 31P NMR spectra were obtained at baseline and throughout ischemia and reperfusion. The pH B was determined with the inorganic phosphate relative to the phosphocreatine resonance signal shift. Profile analysis indicates a difference between groups (P less than .02) related to an initial delay in pH B correction in the tris group. By 48 minutes of reperfusion, pH B did not differ between the groups. Moreover, there was no evidence of paradoxic cerebral acidosis in the bicarb group. Although tris corrects blood pH as quickly as bicarb, it is less effective in correcting pH B. Absence of paradoxic acidosis may be caused by efficient elimination of CO2 by cardiopulmonary bypass.

The stability of DLC film on nitrided CoCrMo alloy in phosphate buffer solution

International Nuclear Information System (INIS)

Zhang, T.F.; Liu, B.; Wu, B.J.; Liu, J.; Sun, H.; Leng, Y.X.; Huang, N.

2014-01-01

CoCrMo alloy is often used as the material for metal artificial joint, but metal debris and metal ions are the main concern on tissue inflammation or tissue proliferation for metal prosthesis. In this paper, nitrogen ion implantation and diamond like carbon (DLC) film composite treatment was used to reduce the wear and ion release of biomedical CoCrMo substrate. The mechanical properties and stability of N-implanted/DLC composite layer in phosphate buffer solution (PBS) was evaluated to explore the full potential of N-implanted/DLC composite layer as an artificial joint surface modification material. The results showed that the DLC film on N implanted CoCrMo (N-implanted/DLC composite layer) had the higher surface hardness and wear resistance than the DLC film on virgin CoCrMo alloy, which was resulted from the strengthen effect of the N implanted layer on CoCrMo alloy. After 30 days immersion in PBS, the structure of DLC film on virgin CoCrMo or on N implanted CoCrMo had no visible change. But the adhesion and corrosion resistance of DLC on N implanted CoCrMo (N-implanted/DLC composite layer) was weakened due to the dissolution of the N implanted layer after 30 days immersion in PBS. The adhesion reduction of N-implanted/DLC composite layer was adverse for in vivo application in long term. So researcher should be cautious to use N implanted layer as an inter-layer for increasing CoCrMo alloy load carrying capacity in vivo environment.

Amine-tethered solid adsorbents coupling high adsorption capacity and regenerability for CO2 capture from ambient air.

Science.gov (United States)

Choi, Sunho; Gray, McMahan L; Jones, Christopher W

2011-05-23

Silica supported poly(ethyleneimine) (PEI) materials are prepared via impregnation and demonstrated to be promising adsorbents for CO(2) capture from ultra-dilute gas streams such as ambient air. A prototypical class 1 adsorbent, containing 45 wt% PEI (PEI/silica), and two new modified PEI-based aminosilica adsorbents, derived from PEI modified with 3-aminopropyltrimethoxysilane (A-PEI/silica) or tetraethyl orthotitanate (T-PEI/silica), are prepared and characterized by using thermogravimetric analysis and FTIR spectroscopy. The modifiers are shown to enhance the thermal stability of the polymer-oxide composites, leading to higher PEI decomposition temperatures. The modified adsorbents present extremely high CO(2) adsorption capacities under conditions simulating ambient air (400 ppm CO(2) in inert gas), exceeding 2 mol(CO (2)) kg(sorbent)(-1), as well as enhanced adsorption kinetics compared to conventional class 1 sorbents. The new adsorbents show excellent stability in cyclic adsorption-desorption operations, even under dry conditions in which aminosilica adsorbents are known to lose capacity due to urea formation. Thus, the adsorbents of this type can be considered promising materials for the direct capture of CO(2) from ultra-dilute gas streams such as ambient air. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Potential impacts of leakage from deep CO2 geosequestration on overlying freshwater aquifers.

Science.gov (United States)

Little, Mark G; Jackson, Robert B

2010-12-01

Carbon Capture and Storage may use deep saline aquifers for CO(2) sequestration, but small CO(2) leakage could pose a risk to overlying fresh groundwater. We performed laboratory incubations of CO(2) infiltration under oxidizing conditions for >300 days on samples from four freshwater aquifers to 1) understand how CO(2) leakage affects freshwater quality; 2) develop selection criteria for deep sequestration sites based on inorganic metal contamination caused by CO(2) leaks to shallow aquifers; and 3) identify geochemical signatures for early detection criteria. After exposure to CO(2), water pH declines of 1-2 units were apparent in all aquifer samples. CO(2) caused concentrations of the alkali and alkaline earths and manganese, cobalt, nickel, and iron to increase by more than 2 orders of magnitude. Potentially dangerous uranium and barium increased throughout the entire experiment in some samples. Solid-phase metal mobility, carbonate buffering capacity, and redox state in the shallow overlying aquifers influence the impact of CO(2) leakage and should be considered when selecting deep geosequestration sites. Manganese, iron, calcium, and pH could be used as geochemical markers of a CO(2) leak, as their concentrations increase within 2 weeks of exposure to CO(2).

An investigation using atomic force microscopy nanoindentation of dental enamel demineralization as a function of undissociated acid concentration and differential buffer capacity

International Nuclear Information System (INIS)

Barbour, Michele E; Shellis, R Peter

2007-01-01

Acidic drinks and foodstuffs can demineralize dental hard tissues, leading to a pathological condition known as dental erosion, which is of increasing clinical concern. The first step in enamel dissolution is a demineralization of the outer few micrometres of tissue, which results in a softening of the structure. The primary determinant of dissolution rate is pH, but the concentration of undissociated acid, which is related to buffer capacity, also appears to be important. In this study, atomic force microscopy nanoindentation was used to measure the first initial demineralization (softening) induced within 1 min by exposure to solutions with a range of undissociated acid concentration and natural pH of 3.3 or with an undissociated acid concentration of 10 mmol l -1 and pH adjusted to 3.3. The results indicate that differential buffering capacity is a better determinant of softening than undissociated acid concentration. Under the conditions of these experiments, a buffer capacity of >3 mmol l -1 pH -1 does not have any further effect on dissolution rate. These results imply that differential buffering capacity should be used for preference over undissociated acid concentration or titratable acidity, which are more commonly employed in the literature

An investigation using atomic force microscopy nanoindentation of dental enamel demineralization as a function of undissociated acid concentration and differential buffer capacity

Science.gov (United States)

Barbour, Michele E.; Shellis, R. Peter

2007-02-01

Acidic drinks and foodstuffs can demineralize dental hard tissues, leading to a pathological condition known as dental erosion, which is of increasing clinical concern. The first step in enamel dissolution is a demineralization of the outer few micrometres of tissue, which results in a softening of the structure. The primary determinant of dissolution rate is pH, but the concentration of undissociated acid, which is related to buffer capacity, also appears to be important. In this study, atomic force microscopy nanoindentation was used to measure the first initial demineralization (softening) induced within 1 min by exposure to solutions with a range of undissociated acid concentration and natural pH of 3.3 or with an undissociated acid concentration of 10 mmol l-1 and pH adjusted to 3.3. The results indicate that differential buffering capacity is a better determinant of softening than undissociated acid concentration. Under the conditions of these experiments, a buffer capacity of >3 mmol l-1 pH-1 does not have any further effect on dissolution rate. These results imply that differential buffering capacity should be used for preference over undissociated acid concentration or titratable acidity, which are more commonly employed in the literature.

Structure and magnetic properties of Co2FeSi film deposited on Si/SiO2 substrate with Cr buffer layer

Science.gov (United States)

Chatterjee, Payel; Basumatary, Himalay; Raja, M. Manivel

2018-05-01

Co2FeSi thin films of 25 nm thickness with 50 nm thick Cr buffer layer was deposited on thermally oxidized Si substrates. Structural and magnetic properties of the films were studied as a function of annealing temperature and substrate temperatures. While the coercivity increases with increase in annealing temperature, it is found to decrease with increase in substrate temperature. A minimum coercivity of 18 Oe has been obtained for the film deposited at 550°C substrate temperature. This was attributed to the formation of L12 phase as observed from the GIXRD studies. The films with a good combination of soft magnetic properties and L21 crystal structure are suitable for spintronic applications.

On the use of dimensionless parameters in acid-base theory: VI. The buffer capacities of equimolar binary mixtures of monovalent weak protolytes as compared to that of bivalent protolytes.

Science.gov (United States)

Rilbe, H

1994-05-01

The general equation for the relative molar buffer capacity, earlier shown to be valid for bivalent acids, bases, and ampholytes, is shown to hold also for equimolar, binary mixtures of monovalent protolytes if only the parameter s = square root of K1'/4K2' is exchanged for t = s + 1/4s. The same applies to the equations for the mean valence of the two classes of protolytes. As a consequence thereof, the titration and buffer capacity curves of a bivalent protolyte are identical with those of a monovalent protolyte with a pK' value equal to the with those of a monovalent protolyte with a pK' value equal to square root of K1'K2' of the bivalent one (the isoprotic point of an ampholyte). For a hypothetical bivalent acid, base, or ampholyte with s = 1, delta pK' = log 4, this implies that the intrinsic rather than the hybrid dissociation constants are responsible for the titration and buffer capacity curves.

Comparative Quantitative Assessments of Salivary Ion Activity Product for Hydroxyapatite and Buffering Capacity in Children with Different Caries Experience.

Science.gov (United States)

Anand, Siddharth; Masih, Updesh; Yeluri, Ramakrishna

If a relation exists between salivary I PHA , buffer capacity and caries experience, then this relationship could be used as screening chair side test for caries risk assessment. One hundred ninety seven children aged 4 to 6 years were examined. Data was collected by interview and clinical examination. They were divided into low, moderate and high caries experience group of 20 children each. Two ml of each sample was used to measure the pH value with pH meter. Regarding the buffering capacity, freshly prepared hydrochloric acid (HCl) was titrated into saliva and pH was recorded. The collected saliva samples were sent to Laboratory for measurement of calcium and phosphorus. I PHA was calculated and the negative logarithms of I PHA were used to determine the enamel solubility. The correlation between salivary I PHA , buffering capacity and caries experience were evaluated. There was a significant relation between pH, log I PHA and dental caries experience, it could be considered as a predictor of dental caries. pH measurement after HCl titration in saliva could be used as chair side screening test for the assessment of caries risk.

Unstimulated Saliva-Related Caries Risk Factors in Individuals with Cystic Fibrosis: A Cross-Sectional Analysis of Unstimulated Salivary Flow, pH, and Buffering Capacity.

Science.gov (United States)

Alkhateeb, Alaa A; Mancl, Lloyd A; Presland, Richard B; Rothen, Marilynn L; Chi, Donald L

2017-01-01

Salivary flow rate, pH, and buffering capacity are associated with dental caries, but studies from the cystic fibrosis (CF) literature are inconclusive regarding these salivary factors and caries. The aim of this study was to evaluate these factors and their associations with dental caries in individuals with CF. Unstimulated whole saliva was collected from individuals aged 6-20 years at Seattle Children's Hospital CF Clinic, USA (n = 83). Salivary flow rate was measured in milliliters per minute. Salivary pH was assessed using a laboratory pH meter. Buffering capacity was assessed by titration with HCl. The outcome measure was caries prevalence, defined as the number of decayed, missing, or filled primary and permanent tooth surfaces. Spearman's rank correlation coefficient and the t test were used to test for bivariate associations. Multiple variable linear regression models were used to (1) run confounder-adjusted analyses and (2) assess for potential interactions. There was no significant association between salivary flow rate or buffering capacity and caries prevalence. There was a significant negative association between salivary pH and caries prevalence, but this association was no longer significant after adjusting for age. There was no significant interaction between salivary flow rate and buffering capacity or between antibiotic use and the 3 salivary factors. Our results indicate that unstimulated salivary factors are not associated with dental caries prevalence in individuals with CF. Future studies should investigate other potential saliva-related caries risk factors in individuals with CF such as cariogenic bacteria levels, salivary host defense peptide levels, and medication use. © 2016 S. Karger AG, Basel.

Screening of Six Medicinal Plant Extracts Obtained by Two Conventional Methods and Supercritical CO2 Extraction Targeted on Coumarin Content, 2,2-Diphenyl-1-picrylhydrazyl Radical Scavenging Capacity and Total Phenols Content

Directory of Open Access Journals (Sweden)

Maja Molnar

2017-02-01

Full Text Available Six medicinal plants Helichrysum italicum (Roth G. Don, Angelica archangelica L., Lavandula officinalis L., Salvia officinalis L., Melilotus officinalis L., and Ruta graveolens L. were used. The aim of the study was to compare their extracts obtained by Soxhlet (hexane extraction, maceration with ethanol (EtOH, and supercritical CO2 extraction (SC-CO2 targeted on coumarin content (by high performance liquid chromatography with ultraviolet detection, HPLC-UV, 2,2-diphenyl-1-picrylhydrazyl radical (DPPH scavenging capacity, and total phenols (TPs content (by Folin–Ciocalteu assay. The highest extraction yields were obtained by EtOH, followed by hexane and SC-CO2. The highest coumarin content (316.37 mg/100 g was found in M. officinalis EtOH extracts, but its SC-CO2 extraction yield was very low for further investigation. Coumarin was also found in SC-CO2 extracts of S. officinalis, R. graveolens, A. archangelica, and L. officinalis. EtOH extracts of all plants exhibited the highest DPPH scavenging capacity. SC-CO2 extracts exhibited antiradical capacity similar to hexane extracts, while S. officinalis SC-CO2 extracts were the most potent (95.7%. EtOH extracts contained the most TPs (up to 132.1 mg gallic acid equivalents (GAE/g from H. italicum in comparison to hexane or SC-CO2 extracts. TPs content was highly correlated to the DPPH scavenging capacity of the extracts. The results indicate that for comprehensive screening of different medicinal plants, various extraction techniques should be used in order to get a better insight into their components content or antiradical capacity.

Vermiculite's strong buffer capacity renders it unsuitable for studies of acidity on soybean (Glycine max L.) nodulation and growth.

Science.gov (United States)

Indrasumunar, Arief; Gresshoff, Peter M

2013-11-14

Vermiculite is the most common soil-free growing substrate used for plants in horticultural and scientific studies due to its high water holding capacity. However, some studies are not suitable to be conducted in it. The described experiments aimed to test the suitability of vermiculite to study the effect of acidity on nodulation and growth of soybean (Glycine max L.). Two different nutrient solutions (Broughton & Dilworth, and modified Herridge nutrient solutions) with or without MES buffer addition were used to irrigate soybean grown on vermiculite growth substrates. The pH of nutrient solutions was adjusted to either pH 4.0 or 7.0 prior its use. The nodulation and vegetative growth of soybean plants were assessed at 3 and 4 weeks after inoculation. The unsuitability of presumably inert vermiculite as a physical plant growth substrate for studying the effects of acidity on soybean nodulation and plant growth was illustrated. Nodulation and growth of soybean grown in vermiculite were not affected by irrigation with pH-adjusted nutrient solution either at pH 4.0 or 7.0. This was reasonably caused by the ability of vermiculite to neutralise (buffer) the pH of the supplied nutrient solution (pH 2.0-7.0). Due to its buffering capacity, vermiculite cannot be used as growth support to study the effect of acidity on nodulation and plant growth.

Estimation of salivary flow rate, pH, buffer capacity, calcium, total protein content and total antioxidant capacity in relation to dental caries severity, age and gender.

Science.gov (United States)

Pandey, Pallavi; Reddy, N Venugopal; Rao, V Arun Prasad; Saxena, Aditya; Chaudhary, C P

2015-03-01

The aim of the study was to evaluate salivary flow rate, pH, buffering capacity, calcium, total protein content and total antioxidant capacity in relation to dental caries, age and gender. The study population consisted of 120 healthy children aged 7-15 years that was further divided into two groups: 7-10 years and 11-15 years. In this 60 children with DMFS/dfs = 0 and 60 children with DMFS/dfs ≥5 were included. The subjects were divided into two groups; Group A: Children with DMFS/dfs = 0 (caries-free) Group B: Children with DMFS/dfs ≥5 (caries active). Unstimulated saliva samples were collected from all groups. Flow rates were determined, and samples analyzed for pH, buffer capacity, calcium, total protein and total antioxidant status. Salivary antioxidant activity is measured with spectrophotometer by an adaptation of 2,2'-azino-di-(3-ethylbenzthiazoline-6-sulphonate) assays. The mean difference of the two groups; caries-free and caries active were proved to be statistically significant (P salivary calcium, total protein and total antioxidant level for both the sexes in the age group 7-10 years and for the age 11-15 years the mean difference of the two groups were proved to be statistically significant (P salivary calcium level for both the sexes. Salivary total protein and total antioxidant level were proved to be statistically significant for male children only. In general, total protein and total antioxidants in saliva were increased with caries activity. Calcium content of saliva was found to be more in caries-free group and increased with age.

Solvent-free nanofluid with three structure models based on the composition of MWCNTs/SiO2 core and its adsorption capacity of CO2.

Science.gov (United States)

Yang, Ruilu; Zheng, Yaping; Wang, Tianyu; Li, Peipei; Wang, Yudeng; Yao, Dongdong; Chen, Lixin

2017-11-26

A series of core/shell nanoparticle organic/inorganic hybrid materials (NOHMs) with different weight ratios of two components, consisting of multi-walled carbon nanotubes (MWCNTs) and silicon dioxide (SiO2) as the core had been synthesized. The NOHMs displays a liquid-like state in the absence of solvent at room temperature. Five NOHMs were categorized into three kinds of structure states based on different weight ratio of two components in core, named power strip model, critical model and collapse model. The capture capacities of these NOHMs for CO2 were investigated at 298 K and CO2 pressures ranging from 0 to 5 MPa. Compared with NOHM having neat MWCNTs core, it had been revealed that NOHMs with power strip model show better adsorption capacity toward CO2, due to its lower viscosity and more reactive groups that can react with CO2. In addition, the capture capacities of NOHMs with critical model were relatively worse than neat MWCNTs-based NOHM. The result is attributed to the aggregation of SiO2 in these samples, which may cause the consumption and hindrance of reactive groups. However, the capture capacity of NOHM with collapse model was the worst in all NOHMs, owing to its lowest content of reactive groups and hollow structure in MWCNTs. Besides, it presented non-interference of MWCNTs and SiO2 without aggregation state. © 2017 IOP Publishing Ltd.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar

2017-03-14

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Capacity gains of buffer-aided moving relays

KAUST Repository

Zafar, Ammar; Shaqfeh, Mohammad; Alnuweiri, Hussein; Alouini, Mohamed-Slim

2017-01-01

This work investigates the gain due to reduction in path loss by deploying buffer-aided moving relaying. In particular, the increase in gain due to moving relays is studied for dual-hop broadcast channels and the bidirectional relay channel. It is shown that the exploited gains in these channels due to buffer-aided relaying can be enhanced by utilizing the fact that a moving relay can communicate with the terminal closest to it and store the data in the buffer and then forward the data to the intended destination when it comes in close proximity with the destination. Numerical results show that for both the considered channels the achievable rates are increased as compared to the case of stationary relays. Numerical results also show that more significant increase in performance is seen when the relay moves to-and-fro between the source and the relay.

Dependence of Magnetic Properties of Co/Pt Multilayers on Deposition Temperature of Pt Buffer Layers

Science.gov (United States)

Shiomi, Shigeru; Nishimura, Tomotaka; Kobayashi, Tadashi; Masuda, Morio

1993-04-01

A 15-nm-thick Pt buffer layer was deposited on a glass slide at temperature Ts(Ptbuf) ranging from 30 to 300°C by e-gun evaporation. Following the cooling in vacuum to ambient temperature, Co and Pt layers have been alternately deposited on it. Very large perpendicular anisotropy and coercivity have been obtained at Ts(Ptbuf) higher than 200°C. The (111) preferred orientation of the Co/Pt multilayer as well as the Pt buffer layer became more pronounced with elevating Ts(Ptbuf), to which the enhancement of perpendicular anisotropy with elevating Ts(Ptbuf) might be ascribable.

Nature-Inspired 2D-Mosaic 3D-Gradient Mesoporous Framework: Bimetal Oxide Dual-Composite Strategy toward Ultrastable and High-Capacity Lithium Storage.

Science.gov (United States)

Yu, Jia; Wang, Yanlei; Mou, Lihui; Fang, Daliang; Chen, Shimou; Zhang, Suojiang

2018-02-27

In allusion to traditional transition-metal oxide (TMO) anodes for lithium-ion batteries, which face severe volume variation and poor conductivity, herein a bimetal oxide dual-composite strategy based on two-dimensional (2D)-mosaic three-dimensional (3D)-gradient design is proposed. Inspired by natural mosaic dominance phenomena, Zn 1-x Co x O/ZnCo 2 O 4 2D-mosaic-hybrid mesoporous ultrathin nanosheets serve as building blocks to assemble into a 3D Zn-Co hierarchical framework. Moreover, a series of derivative frameworks with high evolution are controllably synthesized, based on which a facile one-pot synthesis process can be developed. From a component-composite perspective, both Zn 1-x Co x O and ZnCo 2 O 4 provide superior conductivity due to bimetal doping effect, which is verified by density functional theory calculations. From a structure-composite perspective, 2D-mosaic-hybrid mode gives rise to ladder-type buffering and electrochemical synergistic effect, thus realizing mutual stabilization and activation between the mosaic pair, especially for Zn 1-x Co x O with higher capacity yet higher expansion. Moreover, the inside-out Zn-Co concentration gradient in 3D framework and rich oxygen vacancies further greatly enhance Li storage capability and stability. As a result, a high reversible capacity (1010 mA h g -1 ) and areal capacity (1.48 mA h cm -2 ) are attained, while ultrastable cyclability is obtained during high-rate and long-term cycles, rending great potential of our 2D-mosaic 3D-gradient design together with facile synthesis.

Comparative evaluation of the effects of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and xylitol-containing chewing gum on salivary flow rate, pH and buffering capacity in children: An in vivo study.

Science.gov (United States)

Hegde, Rahul J; Thakkar, Janhavi B

2017-01-01

This study aimed to compare and evaluate the changes in the salivary flow rate, pH, and buffering capacity before and after chewing casein phosphopeptide-amorphous calcium phosphate (CPP-ACP) and xylitol-containing chewing gums in children. Sixty children aged between 8 and 12 years were selected for the study. They were randomly divided into Group 1 (CPP-ACP chewing gum) and Group 2 (xylitol-containing chewing gum) comprising thirty children each. Unstimulated and stimulated saliva samples at 15 and 30 min interval were collected from all children. All the saliva samples were estimated for salivary flow rate, pH, and buffering capacity. Significant increase in salivary flow rate, pH, and buffering capacity from baseline to immediately after spitting the chewing gum was found in both the study groups. No significant difference was found between the two study groups with respect to salivary flow rate and pH. Intergroup comparison indicated a significant increase in salivary buffer capacity in Group 1 when compared to Group 2. Chewing gums containing CPP-ACP and xylitol can significantly increase the physiochemical properties of saliva. These physiochemical properties of saliva have a definite relation with caries activity in children.

PNW cetacean muscle biochemistry - Muscle Myoglobin Content and Acid Buffering Capacity of Cetaceans from the Pacific Northwest to Assess Dive Capacity and the Development of Diving Capabilities

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This project assesses the development of two important skeletal muscle adaptations for diving (enhanced myoglobin content and acid buffering capacities) in a range...

Triazine containing N-rich microporous organic polymers for CO2 capture and unprecedented CO2/N2 selectivity

International Nuclear Information System (INIS)

Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti; Sen, Tapas; Bhaumik, Asim

2017-01-01

Targeted synthesis of microporous adsorbents for CO 2 capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO 2 storage capacities: SB-TRZ-CRZ displayed the CO 2 uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO 2 boosts the selectivity for CO 2 /N 2 . SB-TRZ-CRZ has this CO 2 /N 2 selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues. - Graphical abstract: We report two novel N-rich microporous polymeric materials by doping of triazine containing tripodal dopant in the organic framework. These materials showed excellent CO 2 storage capacities as high as 25.5 wt% under 1 bar pressure with exceptional CO 2 /N 2 selectivity of 377. - Highlights: • Triazine containing trimodal moiety incorporated in polycarbazolic and poly triphenylamine networks. • N-rich crosslinked polymers with high BET surface area and 1.5–1.7 nm size large micropores. • CO 2 uptake capacity of 25.5 wt% upto 1 bar at 273 K. • These crosslinked porous polymers showed exceptional CO 2 /N 2 selectivity.

Pseudo-solid-solution CuCo2O4/C nanofibers as excellent anodes for lithium ion batteries

International Nuclear Information System (INIS)

Zhang, Hang; Tang, Zhiyong; Zhang, Kang; Wang, Lei; Shi, Huimin; Zhang, Guanhua; Duan, Huigao

2017-01-01

Ternary transition metal oxides have received intense research interest as electrode materials for lithium ion batteries, due to their high specific capacity originating from the synergic effects of multiple metal active sites. Reducing the size of metal oxides nanoparticles and dispersing these nanoparticles in carbon matrix are considering effective strategies to improve the electrochemical performance of transition metal oxides. Ternary CuCo 2 O 4 nanoclusters ultra-uniformly dispersed in carbon nanofiber matrix forming a pseudo-solid-solution structure are successfully synthesized by a facile electrospinning method followed by an appropriate annealing process. As the anodic electrode for lithium ion batteries, the pseudo-solid-solution CuCo 2 O 4 /C electrode exhibits a high reversible specific capacity, improved rate capacity and excellent cycling stability. A discharge capacity of 865 mAh g −1 is obtained at the current density of 200 mA g −1 after 400 cycles. Surprisingly, the electrode still retains about 610 mAh g −1 after 800 cycles even at the current density of 600 mA g −1 . The superior lithium storage performance of the pseudo-solid-solution CuCo 2 O 4 /C composites is mainly attributed to the unique amorphous structure. The ultrafine CuCo 2 O 4 nanoclusters uniformly dispersed in carbon matrix can buffer the volume change and improve the conductivity of the metal oxide based electrode, guaranteeing the structure stability and fast electron transfer.

The Li–CO2 battery: a novel method for CO2 capture and utilization

KAUST Repository

Xu, Shaomao; Das, Shyamal K.; Archer, Lynden A.

2013-01-01

We report a novel primary Li-CO2 battery that consumes pure CO2 gas as its cathode. The battery exhibits a high discharge capacity of around 2500 mA h g-1 at moderate temperatures. At 100 °C the discharge capacity is close to 1000% higher than

Reduced endogenous Ca2+ buffering speeds active zone Ca2+ signaling.

Science.gov (United States)

Delvendahl, Igor; Jablonski, Lukasz; Baade, Carolin; Matveev, Victor; Neher, Erwin; Hallermann, Stefan

2015-06-09

Fast synchronous neurotransmitter release at the presynaptic active zone is triggered by local Ca(2+) signals, which are confined in their spatiotemporal extent by endogenous Ca(2+) buffers. However, it remains elusive how rapid and reliable Ca(2+) signaling can be sustained during repetitive release. Here, we established quantitative two-photon Ca(2+) imaging in cerebellar mossy fiber boutons, which fire at exceptionally high rates. We show that endogenous fixed buffers have a surprisingly low Ca(2+)-binding ratio (∼ 15) and low affinity, whereas mobile buffers have high affinity. Experimentally constrained modeling revealed that the low endogenous buffering promotes fast clearance of Ca(2+) from the active zone during repetitive firing. Measuring Ca(2+) signals at different distances from active zones with ultra-high-resolution confirmed our model predictions. Our results lead to the concept that reduced Ca(2+) buffering enables fast active zone Ca(2+) signaling, suggesting that the strength of endogenous Ca(2+) buffering limits the rate of synchronous synaptic transmission.

SODR Memory Control Buffer Control ASIC

Science.gov (United States)

Hodson, Robert F.

1994-01-01

The Spacecraft Optical Disk Recorder (SODR) is a state of the art mass storage system for future NASA missions requiring high transmission rates and a large capacity storage system. This report covers the design and development of an SODR memory buffer control applications specific integrated circuit (ASIC). The memory buffer control ASIC has two primary functions: (1) buffering data to prevent loss of data during disk access times, (2) converting data formats from a high performance parallel interface format to a small computer systems interface format. Ten 144 p in, 50 MHz CMOS ASIC's were designed, fabricated and tested to implement the memory buffer control function.

Solvent-free nanofluid with three structure models based on the composition of a MWCNT/SiO2 core and its adsorption capacity of CO2.

Science.gov (United States)

Yang, R L; Zheng, Y P; Wang, T Y; Li, P P; Wang, Y D; Yao, D D; Chen, L X

2017-12-15

A series of core/shell nanoparticle organic/inorganic hybrid materials (NOHMs) with different weight ratios of two components, consisting of multi-walled carbon nanotubes (MWCNTs) and silicon dioxide (SiO 2 ) as the core were synthesized. The NOHMs display a liquid-like state in the absence of solvent at room temperature. Five NOHMs were categorized into three kinds of structure states based on different weight ratio of two components in the core, named the power strip model, the critical model and the collapse model. The capture capacities of these NOHMs for CO 2 were investigated at 298 K and CO 2 pressures ranging from 0 to 5 MPa. Compared with NOHMs having a neat MWCNT core, it was revealed that NOHMs with the power strip model show better adsorption capacity toward CO 2 due to its lower viscosity and more reactive groups that can react with CO 2 . In addition, the capture capacities of NOHMs with the critical model were relatively worse than the neat MWCNT-based NOHM. The result is attributed to the aggregation of SiO 2 in these samples, which may cause the consumption and hindrance of reactive groups. However, the capture capacity of NOHMs with the collapse model was the worst of all the NOHMs, owing to its lowest content of reactive groups and hollow structure in MWCNTs. In addition, they presented non-interference of MWCNTs and SiO 2 without aggregation state.

Shape- and morphology-controlled sustainable synthesis of Cu, Co, and in metal organic frameworks with high CO2 capture capacity

KAUST Repository

Sarawade, Pradip; Tan, Hua; Polshettiwar, Vivek

2012-01-01

We studied the effects of various surfactants on the shape and morphology of three metal organic frameworks (MOFs), i.e., Co-MOF, Cu-MOF, and In-MOF, which were synthesized under microwave irradiation. The as-synthesized materials were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and nitrogen sorption. The effects of microwave irradiation time, temperature, and surfactant template were investigated. The synthetic parameters, including the type of surfactant template and the reaction temperature, played crucial roles in the size, shape, and morphology of the MOF microcrystals. We also evaluated these MOFs as sorbents for capturing CO2. Of the synthesized materials, Cu-MOF demonstrated the highest CO2 capture capacity, even at atmospheric pressure and ambient temperature. © 2012 American Chemical Society.

Shape- and morphology-controlled sustainable synthesis of Cu, Co, and in metal organic frameworks with high CO2 capture capacity

KAUST Repository

Sarawade, Pradip

2012-11-06

We studied the effects of various surfactants on the shape and morphology of three metal organic frameworks (MOFs), i.e., Co-MOF, Cu-MOF, and In-MOF, which were synthesized under microwave irradiation. The as-synthesized materials were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and nitrogen sorption. The effects of microwave irradiation time, temperature, and surfactant template were investigated. The synthetic parameters, including the type of surfactant template and the reaction temperature, played crucial roles in the size, shape, and morphology of the MOF microcrystals. We also evaluated these MOFs as sorbents for capturing CO2. Of the synthesized materials, Cu-MOF demonstrated the highest CO2 capture capacity, even at atmospheric pressure and ambient temperature. © 2012 American Chemical Society.

Effects of xylitol chewing gum on salivary flow rate, pH, buffering capacity and presence of Streptococcus mutans in saliva.

Science.gov (United States)

Ribelles Llop, M; Guinot Jimeno, F; Mayné Acién, R; Bellet Dalmau, L J

2010-03-01

The first studies on the use of chewing gum in dentistry were done in the 1970s. The Turku Sugar Studies, carried out between 1970 and 1973, showed the excellent anticaries properties of xylitol chewing gums. Since then, many dentists, particularly in Scandinavian countries, have studied the role of chewing xylitol-sweetened chewing gums as another preventive strategy in the control of dental caries. To compare variations in salivary flow rate, pH, buffering capacity, and levels of Streptococcus mutans in baseline conditions and after chewing paraffin pellets or xylitol chewing gum in children between the ages of 6 and 12 years who eat lunch in a school canteen. The study sample consisted of 90 children divided into 2 study groups, and a control group. The children ate lunch at the canteen of the Escultor Ortells state school in the town of Vila-real (Castellón, Spain). The baseline data recorded in the first phase of the study were compared with the data recorded in the second phase, after 15 minutes of chewing xylitol- sweetened chewing gums or paraffin pellets, depending on the study group. Salivary flow rate was measured by collecting the stimulated saliva in a graduated beaker. Levels of pH were measured using a Cyberscan pH 110 pH meter (Eutech Instruments). CRT buffer strips and the CRT bacteria test (Ivoclar-Vivadent) were used to measure buffering capacity and levels of S. mutans, respectively. The data obtained after sample collection were compared by means of a 1-way analysis of variance using the StatGraphics Plus statistical software package, version 5.0. Statistically significant differences were found (ppH, buffering capacity and levels of S. mutans were compared between the 3 groups. Comparison of salivary flow rates revealed no statistically significant differences (p>.05), though salivary flow rates were higher in the groups where gum was chewed. The effect of chewing is essential to the stimulation of salivary flow and the resulting recovery of

Programmable pH buffers

Science.gov (United States)

Gough, Dara Van; Huber, Dale L.; Bunker, Bruce C.; Roberts, Mark E.

2017-01-24

A programmable pH buffer comprises a copolymer that changes pK.sub.a at a lower critical solution temperature (LCST) in water. The copolymer comprises a thermally programmable polymer that undergoes a hydrophobic-to-hydrophilic phase change at the LCST and an electrolytic polymer that exhibits acid-base properties that are responsive to the phase change. The programmable pH buffer can be used to sequester CO.sub.2 into water.

Enhancement in CO2 Adsorption Capacity and Selectivity in the Chalcogenide Aerogel CuSb2S4 by Post-synthetic Modification with LiCl

KAUST Repository

Ahmed, Ejaz

2015-09-11

The new chalcogel CuSb2S4 was obtained by reacting Cu(OAc)2·H2O with KSbS2 in a water/formamide mixture at room temperature. In order to modify the gas adsorption capacity the synthesized CuSb2S4 aerogel was loaded with different amounts of LiCl. CO2 adsorption measurements on the CuSb2S4 aerogel before and after treatment with LiCl showed more than three times increased uptake of the LiCl-modified chalcogel. The selectivities of the gas pairs CO2/H2 and CO2/CH4 in the LiCl-treated chalcogel are 235 and 105 respectively and amongst the highest reported for chalcogenide-based aerogels. In comparison with other porous materials like zeolites, activated carbon and most of the Metal Organic Frameworks (MOFs) or Porous Organic Frameworks (POFs), our synthesized aerogels show good air and moisture stability. Although, the CO2 storage capacity of our aerogels is relatively low, however the selectivity of CO2 over H2 or CH4 in LiCl-loaded aerogels are higher than in zeolites, activated carbon as well as some MOFs like Cu-BTC and MOF-5 etc.

Comparative evaluation of the effects of casein phosphopeptide-amorphous calcium phosphate (CPP-ACP and xylitol-containing chewing gum on salivary flow rate, pH and buffering capacity in children: An in vivo study

Directory of Open Access Journals (Sweden)

Rahul J Hegde

2017-01-01

Full Text Available Aim: This study aimed to compare and evaluate the changes in the salivary flow rate, pH, and buffering capacity before and after chewing casein phosphopeptide-amorphous calcium phosphate (CPP-ACP and xylitol-containing chewing gums in children. Materials and Methods: Sixty children aged between 8 and 12 years were selected for the study. They were randomly divided into Group 1 (CPP-ACP chewing gum and Group 2 (xylitol-containing chewing gum comprising thirty children each. Unstimulated and stimulated saliva samples at 15 and 30 min interval were collected from all children. All the saliva samples were estimated for salivary flow rate, pH, and buffering capacity. Results: Significant increase in salivary flow rate, pH, and buffering capacity from baseline to immediately after spitting the chewing gum was found in both the study groups. No significant difference was found between the two study groups with respect to salivary flow rate and pH. Intergroup comparison indicated a significant increase in salivary buffer capacity in Group 1 when compared to Group 2. Conclusion: Chewing gums containing CPP-ACP and xylitol can significantly increase the physiochemical properties of saliva. These physiochemical properties of saliva have a definite relation with caries activity in children.

Contribution of solution pH and buffer capacity to suppress intergranular stress corrosion cracking of sensitized type 304 stainless steel at 95 C

International Nuclear Information System (INIS)

Zhang, S.; Shibata, T.; Haruna, T.

1999-01-01

Controlling pH of high-temperature water to ∼pH 7 at 300 C by adding lithium hydroxide (LiOH) into the coolant system of a pressurized water reactor (PWR) successfully has been mitigating the corrosion of PWR component materials. The effects of solution pH and buffer capacity on intergranular stress corrosion cracking (IGSCC) of sensitized type 304 stainless steel ([SS] UNS S30400) was examined at 95 C by slow strain rate technique (SSRT) with an in-situ cracking observation system. It was found that an increase in solution pH or buffer capacity increased crack initiation time and decreased mean crack initiation frequency, but exerted almost no effect on crack propagation. This inhibition effect on IGSCC initiation was explained as resulting from a retarding effect of solution pH and buffer capacity on the decrease in pH at crack nuclei caused by the hydrolysis of metal ions dissolved when the passive film was ruptured by strain in SSRT

Electrodeposited binder-free NiCo2O4@carbon nanofiber as a high performance anode for lithium ion batteries

Science.gov (United States)

Zhang, Jie; Chu, Ruixia; Chen, Yanli; Jiang, Heng; Zhang, Ying; Huang, Nay Ming; Guo, Hang

2018-03-01

Binder-free nickel cobaltite on a carbon nanofiber (NiCo2O4@CNF) anode for lithium ion batteries was prepared via a two-step procedure of electrospinning and electrodeposition. The CNF was obtained by annealing electrospun poly-acrylonitrile (PAN) in nitrogen (N2). The NiCo2O4 nanostructures were then grown on the CNF by electrodeposition, followed by annealing in air. Experimental results showed that vertically aligned NiCo2O4 nanosheets had uniformly grown on the surface of the CNF, forming an interconnected network. The NiCo2O4@CNF possessed considerable lithium storage capacity and cycling stability. It exhibited a high reversible capacity of 778 mAhg-1 after 300 cycles at a current density of 0.25 C (1 C = 890 mAg-1) with an average capacity loss rate of 0.05% per cycle. The NiCo2O4@CNF had considerable rate capacities, delivering a capacity of 350 mAhg-1 at a current density of 2.0 C. The outstanding electrochemical performance can be mainly attributed to the following: (1) The nanoscale structure of NiCo2O4 could not only shorten the diffusion path of lithium ions and electrons but also increase the specific surface area, providing more active sites for electrochemical reactions. (2) The CNF with considerable mechanical strength and electrical conductivity could function as an anchor for the NiCo2O4 nanostructure and ensure an efficient electron transfer. (3) The porous structure resulted in a high specific surface area and an effective buffer for the volume changes during the repeated charge-discharge processes. Compared with a conventional hydrothermal method, electrodeposition could significantly simplify the preparation of NiCo2O4, with a shorter preparation period and lower energy consumption. This work provides an alternative strategy to obtain a high performance anode for lithium ion batteries.

Carbon coated CoS_2 thermal battery electrode material with enhanced discharge performances and air stability

International Nuclear Information System (INIS)

Xie, Song; Deng, Yafeng; Mei, Jun; Yang, Zhaotang; Lau, Woon-Ming; Liu, Hao

2017-01-01

Graphical abstract: A novel carbon coated CoS_2 composite is prepared and investigated as a cathode material for thermal batteries. - Highlights: • A novel C@CoS_2 composite is successfully prepared by hydrothermal method. • The growth of CoS_2 in the glucose solution results in a smaller grain size. • The coating of carbon favors electron transfer and buffers polysulfides formation. • The in situ coated carbon layer effectively prevents the oxidation of CoS_2. • The C@CoS_2 composite shows competitive thermal stability and discharge property. - Abstract: Cobalt disulfide (CoS_2) is a promising thermal battery electrode material for its superior thermal stability and discharge performance. However, the low natural resource and poor air stability restrict its application in thermal battery fabrication. In this work, carbon coated CoS_2 composite was prepared by a facile one-pot hydrothermal method with glucose as carbon source. During the growth of CoS_2, the glucose molecules were in situ adsorbed and carbonized on the surface of the as-synthesized CoS_2, and the resultant carbon coating provided improved electrical conductivity and discharge performances to the composite. The thermal battery cell, which was fabricated with such a composite cathode and with a Li-Si anode, can output a capacity of 235.8 mAh g"−"1 and an energy density of 416.9 Wh kg"−"1 at a cut-off voltage of 1.7 V. This carbon coated CoS_2 composite also presented enhanced air stability. After being stored in dry air for 3 months, the composite can still provide a capacity of 232.4 mAh g"−"1 to 1.7 V, whereas the capacity of bare CoS_2 stored with the same condition dropped from 202.4 mAh g"−"1 to 189.7 mAh g"−"1.

Signs of oral dryness in relation to salivary flow rate, pH, buffering capacity and dry mouth complaints

Directory of Open Access Journals (Sweden)

Farsi Najat MA

2007-11-01

Full Text Available Abstract Background This study aimed to investigate the signs of oral dryness in relation to different salivary variables and to correlate subjective complaints of oral dryness with salivary flow rate. Methods 312 unmedicated healthy individuals belonging to three age groups, (6–11, 12–17, and 18–40 years were examined clinically for signs of oral dryness. Resting and stimulated saliva were collected to determine flow rate, pH and buffering capacity. A questionnaire was used to obtain information on subjective sensation of dry mouth. Results Dry lip and dry mucosa were present in 37.5% and 3.2% of the sample respectively. The proportion of subjects who complained of oral dryness (19% showed a stimulated salivary flow rate significantly lower than non complainers. Dry lip was significantly related to low resting flow rate but pH and buffering capacity did not show any significant relation to dry lip. Dry mucosa was not related to any of the above mentioned parameters. Conclusion The finding that the stimulated salivary flow rate was reduced in subjects complaining of dry mouth is of great clinical relevance, since the reduction is expected to be reflected in compromising various salivary functions.

Pb3O4 type antimony oxides MSb2O4 (M = Co, Ni) as anode for Li-ion batteries

International Nuclear Information System (INIS)

Jibin, A.K.; Reddy, M.V.; Subba Rao, G.V.; Varadaraju, U.V.; Chowdari, B.V.R.

2012-01-01

Graphical abstract: Isostructural Pb 3 O 4 type MSb 2 O 4 (M = Co, Ni) compounds were investigated as possible anodes for lithium ion batteries. The reversible capacity is due to electrochemically active Sb and the transition metal and Li 2 O form an inactive matrix which buffers volume variations associated with alloying-de-alloying of antimony. Highlights: ► Isostructural MSb 2 O 4 (M = Co, Ni) were studied as anode for LIBs for first time. ► Li/MSb 2 O 4 (M = Co, Ni) cells displayed reversibility due to electrochemically active Sb. ► CoSb 2 O 4 showed good reversibility compared to NiSb 2 O 4 . - Abstract: Polycrystalline samples of isostructural MSb 2 O 4 (M = Co, Ni) have been prepared by solid state synthesis and lithium-storage is investigated as possible anode materials for lithium-ion batteries. The reaction mechanism of lithium with MSb 2 O 4 (M = Co, Ni) is explored by galvanostatic cycling, cyclic voltammogram and ex situ studies. Both CoSb 2 O 4 and NiSb 2 O 4 exhibit similar electrochemical behavior and show reversible capacity of 490 and 412 mAh g −1 respectively in the first cycle. Reversible alloying de-alloying of Li x Sb takes place in an amorphous matrix of M (Co, Ni) and Li 2 O during electrochemical cycling.

The Li–CO2 battery: a novel method for CO2 capture and utilization

KAUST Repository

Xu, Shaomao

2013-01-01

We report a novel primary Li-CO2 battery that consumes pure CO2 gas as its cathode. The battery exhibits a high discharge capacity of around 2500 mA h g-1 at moderate temperatures. At 100 °C the discharge capacity is close to 1000% higher than that at 40 °C, and the temperature dependence is significantly weaker for higher surface area carbon cathodes. Ex-situ FTIR and XRD analyses convincingly show that lithium carbonate (Li2CO3) is the main component of the discharge product. The feasibility of similar primary metal-CO2 batteries based on earth abundant metal anodes, such as Al and Mg, is demonstrated. The metal-CO2 battery platform provides a novel approach for simultaneous capturing of CO2 emissions and producing electrical energy. © 2013 The Royal Society of Chemistry.

CO 2 Capture Capacity and Swelling Measurements of Liquid-like Nanoparticle Organic Hybrid Materials via Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy

KAUST Repository

Park, Youngjune

2012-01-12

Novel nanoparticle organic hybrid materials (NOHMs), which are comprised of organic oligomers or polymers tethered to an inorganic nanosized cores of various sizes, have been synthesized, and their solvating property for CO 2 was investigated using attenuated total reflectance (ATR) Fourier transform infrared (FT-IR) spectroscopy. Simultaneous measurements of CO 2 capture capacity and swelling behaviors of polyetheramine (Jeffamine M-2070) and its corresponding NOHMs (NOHM-I-PE2070) were reported at temperatures of (298, 308, 323 and 353) K and CO 2 pressure conditions ranging from (0 to 5.5) MPa. The polymeric canopy, or polymer bound to the nanoparticle surface, showed significantly less swelling behavior with enhanced or comparable CO 2 capture capacity compared to pure unbound polyetheramine. © 2011 American Chemical Society.

Evaluation of pH, buffering capacity, viscosity and flow rate levels of saliva in caries-free, minimal caries and nursing caries children: An in vivo study

Directory of Open Access Journals (Sweden)

Dwitha Animireddy

2014-01-01

Full Text Available Background and Aim: The present study was undertaken to evaluate the pH, buffering capacity, viscosity and flow rate of saliva in caries free, minimal caries and nursing caries children and to evaluate the relationship of these on the caries activity of children. Materials and Methods: A total of 75 school children of age group between 4 and 12 years were selected and divided into three equal groups: Group I, Group II and Group III, consisting of 25 subjects each. Group I included caries-free subjects, Group II included subjects with minimal caries and Group III included subjects with nursing caries. Saliva samples were collected from all subjects and were estimated for flow rate, pH, buffering capacity and viscosity. Results: There was a significant decrease in the mean salivary flow rate, salivary ph and salivary buffer capacity and a significant increase in the salivary viscosity among caries-free subjects, subjects with minimal caries and subjects with nursing caries. Conclusion: The physicochemical properties of saliva, such as salivary flow rate, pH, buffering capacity and viscosity, has a relation with caries activity in children and act as markers of caries activity.

Advances in Geological CO{sub 2} Sequestration and Co-Sequestration with O{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Verba, Circe A; O& #x27; Connor, William K.; Ideker, J.H.

2012-10-28

The injection of CO{sub 2} for Enhanced Oil Recovery (EOR) and sequestration in brine-bearing formations for long term storage has been in practice or under investigation in many locations globally. This study focused on the assessment of cement wellbore seal integrity in CO{sub 2}- and CO{sub 2}-O{sub 2}-saturated brine and supercritical CO{sub 2} environments. Brine chemistries (NaCl, MgCl{sub 2}, CaCl{sub 2}) at various saline concentrations were investigated at a pressure of 28.9 MPa (4200 psi) at both 50{degree}C and 85{degree}C. These parameters were selected to simulate downhole conditions at several potential CO{sub 2} injection sites in the United States. Class H portland cement is not thermodynamically stable under these conditions and the formation of carbonic acid degrades the cement. Dissociation occurs and leaches cations, forming a CaCO{sub 3} buffered zone, amorphous silica, and other secondary minerals. Increased temperature affected the structure of C-S-H and the hydration of the cement leading to higher degradation rates.

Ecological complexity buffers the impacts of future climate on marine consumers

Science.gov (United States)

Goldenberg, Silvan U.; Nagelkerken, Ivan; Marangon, Emma; Bonnet, Angélique; Ferreira, Camilo M.; Connell, Sean D.

2018-03-01

Ecological complexity represents a network of interacting components that either propagate or counter the effects of environmental change on individuals and communities1-3. Yet, our understanding of the ecological imprint of ocean acidification (elevated CO2) and climate change (elevated temperature) is largely based on reports of negative effects on single species in simplified laboratory systems4,5. By combining a large mesocosm experiment with a global meta-analysis, we reveal the capacity of consumers (fish and crustaceans) to resist the impacts of elevated CO2. While individual behaviours were impaired by elevated CO2, consumers could restore their performances in more complex environments that allowed for compensatory processes. Consequently, consumers maintained key traits such as foraging, habitat selection and predator avoidance despite elevated CO2 and sustained their populations. Our observed increase in risk-taking under elevated temperature, however, predicts greater vulnerability of consumers to predation. Yet, CO2 as a resource boosted the biomass of consumers through species interactions and may stabilize communities by countering the negative effects of elevated temperature. We conclude that compensatory dynamics inherent in the complexity of nature can buffer the impacts of future climate on species and their communities.

Hollow SnO2@Co3O4 core-shell spheres encapsulated in three-dimensional graphene foams for high performance supercapacitors and lithium-ion batteries

Science.gov (United States)

Zhao, Bo; Huang, Sheng-Yun; Wang, Tao; Zhang, Kai; Yuen, Matthew M. F.; Xu, Jian-Bin; Fu, Xian-Zhu; Sun, Rong; Wong, Ching-Ping

2015-12-01

Hollow SnO2@Co3O4 spheres are fabricated using 300 nm spherical SiO2 particles as template. Then three-dimensional graphene foams encapsulated hollow SnO2@Co3O4 spheres are successfully obtained through self-assembly in hydrothermal process from graphene oxide nanosheets and metal oxide hollow spheres. The three-dimensional graphene foams encapsulated architectures could greatly improve the capacity, cycling stability and rate capability of hollow SnO2@Co3O4 spheres electrodes due to the highly conductive networks and flexible buffering matrix. The three-dimensional graphene foams encapsulated hollow SnO2@Co3O4 spheres are promising electrode materials for supercapacitors and lithium-ion batteries.

Mineralogical controls on porosity and water chemistry during O_2-SO_2-CO_2 reaction of CO_2 storage reservoir and cap-rock core

International Nuclear Information System (INIS)

Pearce, Julie K.; Golab, Alexandra; Dawson, Grant K.W.; Knuefing, Lydia; Goodwin, Carley; Golding, Suzanne D.

2016-01-01

Reservoir and cap-rock core samples with variable lithology's representative of siliciclastic reservoirs used for CO_2 storage have been characterized and reacted at reservoir conditions with an impure CO_2 stream and low salinity brine. Cores from a target CO_2 storage site in Queensland, Australia were tested. Mineralogical controls on the resulting changes to porosity and water chemistry have been identified. The tested siliciclastic reservoir core samples can be grouped generally into three responses to impure CO_2-brine reaction, dependent on mineralogy. The mineralogically clean quartzose reservoir cores had high porosities, with negligible change after reaction, in resolvable porosity or mineralogy, calculated using X-ray micro computed tomography and QEMSCAN. However, strong brine acidification and a high concentration of dissolved sulphate were generated in experiments owing to minimal mineral buffering. Also, the movement of kaolin has the potential to block pore throats and reduce permeability. The reaction of the impure CO_2-brine with calcite-cemented cap-rock core samples caused the largest porosity changes after reaction through calcite dissolution; to the extent that one sample developed a connection of open pores that extended into the core sub-plug. This has the potential to both favor injectivity but also affect CO_2 migration. The dissolution of calcite caused the buffering of acidity resulting in no significant observable silicate dissolution. Clay-rich cap-rock core samples with minor amounts of carbonate minerals had only small changes after reaction. Created porosity appeared mainly disconnected. Changes were instead associated with decreases in density from Fe-leaching of chlorite or dissolution of minor amounts of carbonates and plagioclase. The interbedded sandstone and shale core also developed increased porosity parallel to bedding through dissolution of carbonates and reactive silicates in the sandy layers. Tight interbedded cap

Buffering action of human dentin in vitro.

Science.gov (United States)

Camps, J; Pashley, D H

2000-01-01

The purpose of this study was to determine the relative contributions of the mineral and organic phases of dentin to its total buffering capacity and to compare the buffering abilities of normal and caries-affected dentin for acids used in adhesive dentistry. Disks of normal and caries-affected human coronal dentin 0.6 mm thick were prepared. Fifty microL of various acids were applied to the surface of mineralized or completely demineralized dentin for varying lengths of time. They were collected from the surface and combined with water rinses to permit titration of the total amount of acid applied, the amount recovered, the total amount that was taken up by the dentin, and the amount that diffused across dentin into 1 mL of water. Equal volumes of acids were applied to mineralized or demineralized dentin powder or hydroxyapatite powder. About 88% to 90% of applied acid was recovered from the surface; only 10% to 12% of the acid was taken up by dentin. Of the H+ that was taken up, only 1% to 2% actually diffused across 0.6 mm of dentin. Increasing the application time of 37% phosphoric acid did not increase the amount of H+ that diffused across dentin. Increasing the concentration of phosphoric acid from 10% to 65% produced only slight increases in H+ diffusion across dentin. There was no difference in the buffering capacity of normal vs caries-affected dentin disks. Almost all of the buffering capacity of dentin is due to its mineral phase. The high buffering capacity of dentin and the high reactivity of H+ insure that little H+ diffuses through dentin more than 0.6 mm thick.

Effect of pH buffering capacity and sources of dietary sulfur on rumen fermentation, sulfide production, methane production, sulfate reducing bacteria, and total Archaea in in vitro rumen cultures.

Science.gov (United States)

Wu, Hao; Meng, Qingxiang; Yu, Zhongtang

2015-06-01

The effects of three types of dietary sulfur on in vitro fermentation characteristics, sulfide production, methane production, and microbial populations at two different buffer capacities were examined using in vitro rumen cultures. Addition of dry distilled grain with soluble (DDGS) generally decreased total gas production, degradation of dry matter and neutral detergent fiber, and concentration of total volatile fatty acids, while increasing ammonia concentration. High buffering capacity alleviated these adverse effects on fermentation. Increased sulfur content resulted in decreased methane emission, but total Archaea population was not changed significantly. The population of sulfate reducing bacteria was increased in a sulfur type-dependent manner. These results suggest that types of dietary sulfur and buffering capacity can affect rumen fermentation and sulfide production. Diet buffering capacity, and probably alkalinity, may be increased to alleviate some of the adverse effects associated with feeding DDGS at high levels. Copyright © 2015 Elsevier Ltd. All rights reserved.

High-Thermal- and Air-Stability Cathode Material with Concentration-Gradient Buffer for Li-Ion Batteries.

Science.gov (United States)

Shi, Ji-Lei; Qi, Ran; Zhang, Xu-Dong; Wang, Peng-Fei; Fu, Wei-Gui; Yin, Ya-Xia; Xu, Jian; Wan, Li-Jun; Guo, Yu-Guo

2017-12-13

Delivery of high capacity with high thermal and air stability is a great challenge in the development of Ni-rich layered cathodes for commercialized Li-ion batteries (LIBs). Herein we present a surface concentration-gradient spherical particle with varying elemental composition from the outer end LiNi 1/3 Co 1/3 Mn 1/3 O 2 (NCM) to the inner end LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA). This cathode material with the merit of NCM concentration-gradient protective buffer and the inner NCA core shows high capacity retention of 99.8% after 200 cycles at 0.5 C. Furthermore, this cathode material exhibits much improved thermal and air stability compared with bare NCA. These results provide new insights into the structural design of high-performance cathodes with high energy density, long life span, and storage stability materials for LIBs in the future.

Terrestrial biosphere models underestimate photosynthetic capacity and CO2 assimilation in the Arctic.

Science.gov (United States)

Rogers, Alistair; Serbin, Shawn P; Ely, Kim S; Sloan, Victoria L; Wullschleger, Stan D

2017-12-01

Terrestrial biosphere models (TBMs) are highly sensitive to model representation of photosynthesis, in particular the parameters maximum carboxylation rate and maximum electron transport rate at 25°C (V c,max.25 and J max.25 , respectively). Many TBMs do not include representation of Arctic plants, and those that do rely on understanding and parameterization from temperate species. We measured photosynthetic CO 2 response curves and leaf nitrogen (N) content in species representing the dominant vascular plant functional types found on the coastal tundra near Barrow, Alaska. The activation energies associated with the temperature response functions of V c,max and J max were 17% lower than commonly used values. When scaled to 25°C, V c,max.25 and J max.25 were two- to five-fold higher than the values used to parameterize current TBMs. This high photosynthetic capacity was attributable to a high leaf N content and the high fraction of N invested in Rubisco. Leaf-level modeling demonstrated that current parameterization of TBMs resulted in a two-fold underestimation of the capacity for leaf-level CO 2 assimilation in Arctic vegetation. This study highlights the poor representation of Arctic photosynthesis in TBMs, and provides the critical data necessary to improve our ability to project the response of the Arctic to global environmental change. No claim to original US Government works. New Phytologist © 2017 New Phytologist Trust.

CO2 cycle

Science.gov (United States)

Titus, Timothy N.; Byrne, Shane; Colaprete, Anthony; Forget, Francois; Michaels, Timothy I.; Prettyman, Thomas H.

2017-01-01

This chapter discusses the use of models, observations, and laboratory experiments to understand the cycling of CO2 between the atmosphere and seasonal Martian polar caps. This cycle is primarily controlled by the polar heat budget, and thus the emphasis here is on its components, including solar and infrared radiation, the effect of clouds (water- and CO2-ice), atmospheric transport, and subsurface heat conduction. There is a discussion about cap properties including growth and regression rates, albedos and emissivities, grain sizes and dust and/or water-ice contamination, and curious features like cold gas jets and araneiform (spider-shaped) terrain. The nature of the residual south polar cap is discussed as well as its long-term stability and ability to buffer atmospheric pressures. There is also a discussion of the consequences of the CO2 cycle as revealed by the non-condensable gas enrichment observed by Odyssey and modeled by various groups.

Enhanced Selectivity and Uptake Capacity of CO2 and Toluene Adsorption in Co0.5 M0.33 MoS4 (M= Sb or Y) Chalcogels by Impregnated Metal Salts

KAUST Repository

Adhiam, Fatima Abdullah Ahmed

2017-11-17

The synthesis of metal chalcogenide aerogels Co0.5M0.33MoS4 (M= Sb or Y) by the sol-gel method is reported. In this system, the building blocks [MoS4]2− chelated with Co2+ and (Sb3+) or (Y3+) salts in nonaqueous solvents forming amorphous networks with a gel property. The chalcogels obtained after supercritical drying have BET surface areas of 176 m2 g−1 (Co0.5Sb0.33MoS4) and 145 m2 g−1 (Co0.5Y0.33MoS4). Electron microscopy and physisorption studies reveal that the new materials are porous with wide pore size distribution and average pore width of 16 nm. These chalcogels show higher adsorption capacity of toluene vapor (Co0.5Sb0.33MoS4: 387 mg g−1) and (Co0.5Y0.33MoS4: 304 mg g−1) over cyclohexane vapor and high selectivity of CO2 over CH4 or H2, Co0.5Sb0.33MoS4 (CO2/H2: 80 and CO2/CH4: 21), Co0.5Y0.33MoS4 (CO2/H2: 27 and CO2/CH4: 15). We also demonstrated that the impregnation of various metal species like Li+, Mg2+, and Ni2+ significantly enhanced the uptake capacity and selectivity of toluene and CO2 adsorptions in the chacogels.

Simulation of CO2 Sequestration at Rock Spring Uplift, Wyoming: Heterogeneity and Uncertainties in Storage Capacity, Injectivity and Leakage

Energy Technology Data Exchange (ETDEWEB)

Deng, Hailin [Los Alamos National Laboratory; Dai, Zhenxue [Los Alamos National Laboratory; Jiao, Zunsheng [Wyoming State Geological Survey; Stauffer, Philip H. [Los Alamos National Laboratory; Surdam, Ronald C. [Wyoming State Geological Survey

2011-01-01

Many geological, geochemical, geomechanical and hydrogeological factors control CO{sub 2} storage in subsurface. Among them heterogeneity in saline aquifer can seriously influence design of injection wells, CO{sub 2} injection rate, CO{sub 2} plume migration, storage capacity, and potential leakage and risk assessment. This study applies indicator geostatistics, transition probability and Markov chain model at the Rock Springs Uplift, Wyoming generating facies-based heterogeneous fields for porosity and permeability in target saline aquifer (Pennsylvanian Weber sandstone) and surrounding rocks (Phosphoria, Madison and cap-rock Chugwater). A multiphase flow simulator FEHM is then used to model injection of CO{sub 2} into the target saline aquifer involving field-scale heterogeneity. The results reveal that (1) CO{sub 2} injection rates in different injection wells significantly change with local permeability distributions; (2) brine production rates in different pumping wells are also significantly impacted by the spatial heterogeneity in permeability; (3) liquid pressure evolution during and after CO{sub 2} injection in saline aquifer varies greatly for different realizations of random permeability fields, and this has potential important effects on hydraulic fracturing of the reservoir rock, reactivation of pre-existing faults and the integrity of the cap-rock; (4) CO{sub 2} storage capacity estimate for Rock Springs Uplift is 6614 {+-} 256 Mt at 95% confidence interval, which is about 36% of previous estimate based on homogeneous and isotropic storage formation; (5) density profiles show that the density of injected CO{sub 2} below 3 km is close to that of the ambient brine with given geothermal gradient and brine concentration, which indicates CO{sub 2} plume can sink to the deep before reaching thermal equilibrium with brine. Finally, we present uncertainty analysis of CO{sub 2} leakage into overlying formations due to heterogeneity in both the target saline

Triazine containing N-rich microporous organic polymers for CO{sub 2} capture and unprecedented CO{sub 2}/N{sub 2} selectivity

Energy Technology Data Exchange (ETDEWEB)

Bhunia, Subhajit; Bhanja, Piyali; Das, Sabuj Kanti [Department of Material Science, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India); Sen, Tapas [Nanobiomaterials Research Group, Centre for Materials Science, School of Physical Sciences and Computing, University of Central Lancashire, Preston PR1 2HE (United Kingdom); Bhaumik, Asim, E-mail: msab@iacs.res.in [Department of Material Science, Indian Association for the Cultivation of Science, Jadavpur, Kolkata 700032 (India)

2017-03-15

Targeted synthesis of microporous adsorbents for CO{sub 2} capture and storage is very challenging in the context of remediation from green house gases. Herein we report two novel N-rich microporous networks SB-TRZ-CRZ and SB-TRZ-TPA by extensive incorporation of triazine containing tripodal moiety in the porous polymer framework. These materials showed excellent CO{sub 2} storage capacities: SB-TRZ-CRZ displayed the CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K and SB-TRZ-TPA gave that of 16 wt% under identical conditions. The substantial dipole quadruple interaction between network (polar triazine) and CO{sub 2} boosts the selectivity for CO{sub 2}/N{sub 2}. SB-TRZ-CRZ has this CO{sub 2}/N{sub 2} selectivity ratio of 377, whereas for SB-TRZ-TPA it was 97. Compared to other porous polymers, these materials are very cost effective, scalable and very promising material for clean energy application and environmental issues. - Graphical abstract: We report two novel N-rich microporous polymeric materials by doping of triazine containing tripodal dopant in the organic framework. These materials showed excellent CO{sub 2} storage capacities as high as 25.5 wt% under 1 bar pressure with exceptional CO{sub 2}/N{sub 2} selectivity of 377. - Highlights: • Triazine containing trimodal moiety incorporated in polycarbazolic and poly triphenylamine networks. • N-rich crosslinked polymers with high BET surface area and 1.5–1.7 nm size large micropores. • CO{sub 2} uptake capacity of 25.5 wt% upto 1 bar at 273 K. • These crosslinked porous polymers showed exceptional CO{sub 2}/N{sub 2} selectivity.

Foamlike porous spinel Mn(x)Co(3-x)O4 material derived from Mn3[Co(CN)6]2⋅nH2O nanocubes: a highly efficient anode material for lithium batteries.

Science.gov (United States)

Hu, Lin; Zhang, Ping; Zhong, Hao; Zheng, Xinrui; Yan, Nan; Chen, Qianwang

2012-11-19

A new facile strategy has been designed to fabricate spinel Mn(x)Co(3-x)O(4) porous nanocubes, which involves a morphology-conserved and pyrolysis-induced transformation of Prussian Blue Analogue Mn(3)[Co(CN)(6)](2)⋅nH(2)O perfect nanocubes. Owing to the release of CO(2) and N(x)O(y) in the process of interdiffusion, this strategy can overcome to a large extent the disadvantage of the traditional ceramic route for synthesis of spinels, and Mn(x)Co(3-x)O(4) with foamlike porous nanostructure is effectively obtained. Importantly, when evaluated as an electrode material for lithium-ion batteries, the foamlike Mn(x)Co(3-x)O(4) porous nanocubes display high specific discharge capacity and excellent rate capability. The improved electrochemical performance is attributed to the beneficial features of the particular foamlike porous nanostructure and large surface area, which reduce the diffusion length for Li(+) ions and enhance the structural integrity with sufficient void space for buffering the volume variation during the Li(+) insertion/extraction. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Expanding Resilience Indicators: A Case Study on Buffering Capacity Indicator in a Process Plant

Directory of Open Access Journals (Sweden)

Shirali

2016-03-01

Full Text Available Background The complexity of modern sociotechnical systems has created new challenges for safety, so that traditional approaches are not able to cope with them. Resilience engineering (RE is a good alternative to traditional approaches for safety management, however resilience is still a difficult concept to measure, and indicators such as buffering capacity, flexibility, and so on, which are thought to contribute to it, are undeveloped. Objectives This study aimed at expanding buffering capacity as one of the main indicators in order to facilitate measurement of resilience of a system. Materials and Methods We used the Delphi method in order to identify indicators, and data related to all the indicators were gathered by observation and interview. In this line, 32 of the experienced operators with at least 15 years of operational record were selected for semi-structured interviews. Gathered data was processed by the principal component analysis technique. The results were processed by the Minitab 15 software. Results In this study, 29 factors affecting this indicator were determined using the Delphi method; the scores of all factors were less than the scores of the best practice. On the other hand, the state of this indicator was poor in plant included in the study. Conclusions This was the first study that focused on expanding resilience indicators, and presents a new framework to simplify assessment of resilience and safety of a complex system.

Anodic electrochemical performances of MgCo{sub 2}O{sub 4} synthesized by oxalate decomposition method and electrospinning technique for Li-ion battery application

Energy Technology Data Exchange (ETDEWEB)

Darbar, Devendrasinh [School of Mechanical and Building Science, Vellore Institute of Technology (VIT), Vellore 632014, Tamil Nadu (India); Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Department of Physics, National University of Singapore, 117542 (Singapore); Reddy, M.V., E-mail: phymvvr@nus.edu.sg [Department of Physics, National University of Singapore, 117542 (Singapore); Department of Materials Science and Engineering, National University of Singapore, 117546 (Singapore); Sundarrajan, S. [Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Pattabiraman, R. [School of Mechanical and Building Science, Vellore Institute of Technology (VIT), Vellore 632014, Tamil Nadu (India); Ramakrishna, S. [Department of Mechanical Engineering, National University of Singapore, 117576 (Singapore); Chowdari, B.V.R. [Department of Physics, National University of Singapore, 117542 (Singapore)

2016-01-15

Highlights: • MgCo{sub 2}O{sub 4} was prepared by oxalate decomposition method and electrospinning technique. • Electrospun MgCo{sub 2}O{sub 4} shows the reversible capacity of 795 and 227 mAh g{sup −1} oxalate decomposition MgCo{sub 2}O{sub 4} after 50 cycle. • Electrospun MgCo{sub 2}O{sub 4} show good cycling stability and electrochemical performance. - Abstract: Magnesium cobalt oxide, MgCo{sub 2}O{sub 4} was synthesized by oxalate decomposition method and electrospinning technique. The electrochemical performances, structures, phase formation and morphology of MgCo{sub 2}O{sub 4} synthesized by both the methods are compared. Scanning electron microscope (SEM) studies show spherical and fiber type morphology, respectively for the oxalate decomposition and electrospinning method. The electrospun nanofibers of MgCo{sub 2}O{sub 4} calcined at 650 °C, showed a very good reversible capacity of 795 mAh g{sup −1} after 50 cycles when compared to bulk material capacity of 227 mAh g{sup −1} at current rate of 60 mA g{sup −1}. MgCo{sub 2}O{sub 4} nanofiber showed a reversible capacity of 411 mAh g{sup −1} (at cycle) at current density of 240 mA g{sup −1}. Improved performance was due to improved conductivity of MgO, which may act as buffer layer leading to improved cycling stability. The cyclic voltammetry studies at scan rate of 0.058 mV/s show main cathodic at around 1.0 V and anodic peaks at 2.1 V vs. Li.

Effect of the both texture and electrical properties of activated carbon on the CO{sub 2} adsorption capacity

Energy Technology Data Exchange (ETDEWEB)

Djeridi, W. [Research Laboratory: Engineering Process and Industrial Systems, National school of Engineers of Gabes, University of Gabes, St Omar Ibn Elkhattab, 6029 Gabes (Tunisia); Chimistry laboratory of Provence, University Aix-Marseille I, II, III- CNRS, UMR 6264, Centre de Saint Jerome, 13397 Marseille (France); Ouederni, A. [Research Laboratory: Engineering Process and Industrial Systems, National school of Engineers of Gabes, University of Gabes, St Omar Ibn Elkhattab, 6029 Gabes (Tunisia); Mansour, N.Ben [National Nanotechnology Research Centre, KACST, Riyadh (Saudi Arabia); Llewellyn, P.L. [Chimistry laboratory of Provence, University Aix-Marseille I, II, III- CNRS, UMR 6264, Centre de Saint Jerome, 13397 Marseille (France); Alyamani, A. [National Nanotechnology Research Centre, KACST, Riyadh (Saudi Arabia); El Mir, L., E-mail: djeridiwahid@yahoo.fr [Laboratory of Physics of Materials and Nanomaterials Applied at Environment (LaPhyMNE), Gabes University, Faculty of Sciences in Gabes, Gabes (Tunisia); Al Imam Mohammad Ibn Saud Islamic University (IMSIU), College of Sciences, Department of Physics, 11623 Riyadh (Saudi Arabia)

2016-01-15

Highlights: • A series of activated carbon pellet without binder was prepared by chemical activation. • Carbon dioxide storage isotherm at 30 °C and up to 25 bars was measured for the microporous carbon. • Adsorption enthalpies have been correlated with the carbon dioxide uptake. • Pyrolysis temperature effect on the electrical conductivity of the samples. • Impact of the both texture and electrical properties on CO{sub 2} adsorption capacity have been deducted - Abstract: A series of activated carbon pellets (ACP) based on olive stones were studied for CO{sub 2} storage application. The surface area, pore volume, and pore diameter were evaluated from the analysis of N{sub 2} adsorption isotherm data. The characterization of carbon materials was performed by scanning electron microscopy (SEM), the powder X-ray diffraction (PXRD) and transmission electron microscopy (TEM). The adsorption enthalpies were obtained by microcalorimetry. The effect of pyrolysis temperature on textural, electrical conductivity and gas adsorption capacities of the ACP were investigated by adsorbing CO{sub 2} at 303 K in the pressure range of 0–2.3 MPa. In fact the electrical conductivity is strongly affected by the microporosity of the samples and the size of the micropore. It increases when the pore size decreases which affect the CO{sub 2} adsorption. Also with increases temperature the free electrons concentration on the surface increases which affect the interaction of the adsorbed gas molecules.

Study of the influence of Nb buffer layer on the exchange coupling induced at the Co/IrMn interface

Energy Technology Data Exchange (ETDEWEB)

Merino, I.L.C., E-mail: isabel5cas@gmail.com [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180 (Brazil); Figueiredo, L.C. [Instituto de Física, Universidade de Brasília, Brasília 70910-900 (Brazil); Passamani, E.C.; Nascimento, V.P. [Departamento de Física, Universidade Federal do Espírito Santo, Vitória 29075-910 (Brazil); Pelegrini, F. [Instituto de Física, Universidade Federal de Goiás, Goiânia 74560-900 (Brazil); Baggio Saitovitch, E. [Centro Brasileiro de Pesquisas Físicas, Rio de Janeiro 22290-180 (Brazil)

2017-06-15

Highlights: • Nb buffer layer favors smooth/rough Co/IrMn interfaces, depending on its thickness. • Double and single-like hysteresis loop features depend on the Nb thickness. • Co uniaxial anisotropy induced exchange-bias in as-deposited sample. • Uniaxial and exchange-bias anisotropy directions depend on the Nb thickness. • Thicker Nb favors non-collinear anisotropies, while thinner Nb favors collinear. - Abstract: Hybrid Nb(t{sub Nb})/Co(10 nm)/IrMn(15 nm)/Nb(10 nm) heterostructured materials were prepared by DC Magnetron Sputtering and systematically studied by X-ray, magnetization and ferromagnetic resonance techniques. For thinner Nb buffer layer (≤10 nm), it was found that there is an inter-diffusion at Co/IrMn interface, which favors double-like hysteresis loop. For thicker Nb layers, however, a gradual transition from double to single-like hysteresis loops is observed and it is associated with the reduction of the Nb roughness, which also enhances the exchange coupling at the Co/IrMn interface. Nb grown on IrMn layer induces the formation of an NbIrMn alloy layer, while no evidence of inter-diffusion at the Co/Nb interface is observed. For rougher Nb buffer layers (t{sub Nb} < 50 nm), exchange bias and Co uniaxial anisotropies are pointing at the same direction (β∼zero), but for smoother Nb buffer layer (t{sub Nb} = 50 nm) a β angle of 150{sup o} is found. Exchange bias effect was measured in as-prepared and in field-cooled samples; being its presence, in as-prepared sample, attributed to the unidirectional anisotropy of the Co layer (its intensity is modified in case of sample with a CoIrMn alloy layer). Considering that the Si/Nb/Co/IrMn interfaces have different β values (t{sub Nb} = 35 and 50 nm), a study of the influence of magnetization direction, governed by exchange-biased layers, on superconducting properties of Nb films can be successfully done in this hybrid system.

Bifunctional composite catalysts using Co3O4 nanofibers immobilized on nonoxidized graphene nanoflakes for high-capacity and long-cycle Li-O2 batteries.

Science.gov (United States)

Ryu, Won-Hee; Yoon, Taek-Han; Song, Sung Ho; Jeon, Seokwoo; Park, Yong-Joon; Kim, Il-Doo

2013-09-11

Designing a highly efficient catalyst is essential to improve the electrochemical performance of Li-O2 batteries for long-term cycling. Furthermore, these batteries often show significant capacity fading due to the irreversible reaction characteristics of the Li2O2 product. To overcome these limitations, we propose a bifunctional composite catalyst composed of electrospun one-dimensional (1D) Co3O4 nanofibers (NFs) immobilized on both sides of the 2D nonoxidized graphene nanoflakes (GNFs) for an oxygen electrode in Li-O2 batteries. Highly conductive GNFs with noncovalent functionalization can facilitate a homogeneous dispersion in solution, thereby enabling simple and uniform attachment of 1D Co3O4 NFs on GNFs without restacking. High first discharge capacity of 10 500 mAh/g and superior cyclability for 80 cycles with a limited capacity of 1000 mAh/g were achieved by (i) improved catalytic activity of 1D Co3O4 NFs with large surface area, (ii) facile electron transport via interconnected GNFs functionalized by Co3O4 NFs, and (iii) fast O2 diffusion through the ultrathin GNF layer and porous Co3O4 NF networks.

Anatase TiO2 as a Cheap and Sustainable Buffering Filler for Silicon Nanoparticles in Lithium-Ion Battery Anodes.

Science.gov (United States)

Maroni, Fabio; Carbonari, Gilberto; Croce, Fausto; Tossici, Roberto; Nobili, Francesco

2017-12-08

The design of effective supporting matrices to efficiently cycle Si nanoparticles is often difficult to achieve and requires complex preparation strategies. In this work, we present a simple synthesis of low-cost and environmentally benign aAnatase TiO 2 nanoparticles as buffering filler for Si nanoparticles (Si@TiO 2 ). The average anatase TiO 2 crystallite size was approximately 5 nm. A complete structural, morphological, and electrochemical characterization was performed. Electrochemical test results show very good specific capacity values of up to 1000 mAh g -1 and cycling at several specific currents, ranging from 500 to 2000 mA g -1 , demonstrating a very good tolerance to high cycling rates. Postmortem morphological analysis shows very good electrode integrity after 100 cycles at 500 mA g -1 specific current. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Catalyst functionalized buffer sorbent pebbles for rapid separation of carbon dioxide from gas mixtures

Energy Technology Data Exchange (ETDEWEB)

Aines, Roger D

2015-03-31

A method for separating CO.sub.2 from gas mixtures uses a slurried media impregnated with buffer compounds and coating the solid media with a catalyst or enzyme that promotes the transformation of CO.sub.2 to carbonic acid. Buffer sorbent pebbles with a catalyst or enzyme coating are provided for rapid separation of CO.sub.2 from gas mixtures.

Catalyst functionalized buffer sorbent pebbles for rapid separation of carbon dioxide from gas mixtures

Science.gov (United States)

Aines, Roger D.

2013-03-12

A method for separating CO.sub.2 from gas mixtures uses a slurried media impregnated with buffer compounds and coating the solid media with a catalyst or enzyme that promotes the transformation of CO.sub.2 to carbonic acid. Buffer sorbent pebbles with a catalyst or enzyme coating are provided for rapid separation of CO.sub.2 from gas mixtures.

Weakened Intracellular Zn2+-Buffering in the Aged Dentate Gyrus and Its Involvement in Erasure of Maintained LTP.

Science.gov (United States)

Takeda, Atsushi; Tamano, Haruna; Murakami, Taku; Nakada, Hiroyuki; Minamino, Tatsuya; Koike, Yuta

2018-05-01

Memory is lost by the increased influx of extracellular Zn 2+ into neurons. It is possible that intracellular Zn 2+ dynamics is modified even at non-zincergic medial perforant pathway-dentate granule cell synapses along with aging and that vulnerability to the modification is linked to age-related cognitive decline. To examine these possibilities, vulnerability of long-term potentiation (LTP) maintenance, which underlies memory retention, to modification of synaptic Zn 2+ dynamics was compared between young and aged rats. The influx of extracellular Zn 2+ into dentate granule cells was increased in aged rats after injection of high K + into the dentate gyrus, but not in young rats. This increase impaired maintained LTP in aged rats. However, the impairment was rescued by co-injection of CaEDTA, an extracellular Zn 2+ chelator, or CNQX, an AMPA receptor antagonist, which suppressed the Zn 2+ influx. Maintained LTP was also impaired in aged rats after injection of ZnAF-2DA into the dentate gyrus that chelates intracellular Zn 2+ , but not in young rats. Interestingly, the capacity of chelating intracellular Zn 2+ with intracellular ZnAF-2 was almost lost in the aged dentate gyrus 2 h after injection of ZnAF-2DA into the dentate gyrus, suggesting that intracellular Zn 2+ -buffering is weakened in the aged dentate gyrus, compared to the young dentate gyrus. In the dentate gyrus of aged rats, maintained LTP is more vulnerable to modification of intracellular Zn 2+ dynamics than in young rats, probably due to weakened intracellular Zn 2+ -buffering.

Preliminary findings on the correlation of saliva pH, buffering capacity, flow rate and consistency in relation to waterpipe tobacco smoking.

Science.gov (United States)

Khemiss, Mehdi; Ben Khelifa, Mohamed; Ben Saad, Helmi

2017-12-01

The aim of the present comparative study was to compare some salivary characteristics between exclusive waterpipe smokers (EWPS) and non-smokers. 72 males (36 EWPS) were recruited. The volume of stimulated saliva was determined and divided by the duration of saliva collection. The pH was measured directly using a pH meter. The buffering capacity was determined using a quantitative method which involved the addition of 10 µl HCl. Up to a total of 160 µL was titrated up to obtain a pH titration curve. At 50 µL of titrated HCl, buffering capacity was ranked into three categories: high, medium and low. EWPS and non-smoker groups had similar flow rates (1.81 ± 0.79 and 1.78 ± 1.14 mL min-1) and similar baseline pH (6.60 ± 0.37 and 6.76 ± 0.39). Statistically significant differences in the two groups' pH were observed from 30 to 160 µL of titrated up HCl. At 50 µL of titrated up HCl, the EWPS group compared to the non-smoker group had a significantly higher pH (4.79 ± 0.72 vs. 5.32 ± 0.79). To conclude, waterpipe tobacco smoking alters the buffering capacity but does not alter either salivary flow rates or the baseline pH and consistency.

The pH-static enzyme sensor : An ISFET-based enzyme sensor, insensitive to the buffer capacity of the sample

NARCIS (Netherlands)

van der Schoot, Bart H.; Bergveld, Piet

1987-01-01

An ISFET-based urea sensor is combined with a noble-metal electrode which provides continuous coulometric titration of the products of the enzymatic reaction. The sensor thus becomes independent of the buffer capacity of the sample; and because the enzyme is operating at a constant pH, the linear

A reaction-diffusion model of CO2 influx into an oocyte

Science.gov (United States)

Somersalo, Erkki; Occhipinti, Rossana; Boron, Walter F.; Calvetti, Daniela

2012-01-01

We have developed and implemented a novel mathematical model for simulating transients in surface pH (pHS) and intracellular pH (pHi) caused by the influx of carbon dioxide (CO2) into a Xenopus oocyte. These transients are important tools for studying gas channels. We assume that the oocyte is a sphere surrounded by a thin layer of unstirred fluid, the extracellular unconvected fluid (EUF), which is in turn surrounded by the well-stirred bulk extracellular fluid (BECF) that represents an infinite reservoir for all solutes. Here, we assume that the oocyte plasma membrane is permeable only to CO2. In both the EUF and intracellular space, solute concentrations can change because of diffusion and reactions. The reactions are the slow equilibration of the CO2 hydration-dehydration reactions and competing equilibria among carbonic acid (H2CO3)/bicarbonate ( HCO3-) and a multitude of non-CO2/HCO3- buffers. Mathematically, the model is described by a coupled system of reaction-diffusion equations that—assuming spherical radial symmetry—we solved using the method of lines with appropriate stiff solvers. In agreement with experimental data (Musa-Aziz et al, PNAS 2009, 106:5406–5411), the model predicts that exposing the cell to extracellular 1.5% CO2/10 mM HCO3- (pH 7.50) causes pHi to fall and pHS to rise rapidly to a peak and then decay. Moreover, the model provides insights into the competition between diffusion and reaction processes when we change the width of the EUF, membrane permeability to CO2, native extra-and intracellular carbonic anhydrase-like activities, the non-CO2/HCO3- (intrinsic) intracellular buffering power, or mobility of intrinsic intracellular buffers. PMID:22728674

Effects of Regeneration Conditions on Sorption Capacity of CO{sub 2} Dry Potassium Sorbent During Carbonation

Energy Technology Data Exchange (ETDEWEB)

Kim, Yunseop; Park, Young Cheol; Jo, Sung-Ho; Ryu, Ho-Jung; Yi, Chang-Keun [Korea Institute of Energy Research, Daejeon (Korea, Republic of); Rhee, Young Woo [Chungnam National University, Daejeon (Korea, Republic of)

2015-02-15

In this study, we investigated carbonation-regeneration and agglomeration characteristics of dry sorbents. Experiment has been proceeded in the batch-type reactor, which is made of quartz: 0.05 m of I.D and 0.8 m in height. The sorbents that is collected at the cyclone of the carbonation reactor of continuous process were used in this study. The reactivity was studied at the various concentrations of water vapor, N{sub 2} and CO{sub 2} in the fluidizing gas at regeneration reaction. As a result, the reactivity increased as the regeneration temperature increased, the reactivity decreased as the concentration of water vapor increased. The absorption capacity showed the highest value in case of using N{sub 2} 100% as regeneration gas. And decreased in order of H{sub 2}O+N{sub 2}, CO{sub 2} 100% and H{sub 2}O+CO{sub 2}. The agglomeration characteristics were investigated according to the particle sizes and concentrations of water vapor at carbonation reaction. As a result, the particle with smaller size and higher concentration of water vapor showed the higher agglomeration characteristic.

Volatilization-excitation phenomena and efficiency of spectrochemical buffers in the analysis of geological samples. I. The action of the mixture Li2CO3: Grafite

International Nuclear Information System (INIS)

Diaz-Guerra, J.P.; Roca, M.

1984-01-01

The volatilization-excitation mechanisms of Li 2 CO 3 , SrCO 3 and GeO 2 as buffers for the determination of different major constituents in geological samples have been investigated considering the phenomena taking place in the electrode, anodic load and are plasma. The present paper deals with the evaluation of fundamental parameters and processes in d.c. are that have first been applied to the study of a Li 2 CO 3 : graphite (1:1) mixture. A second paper Is devoted to ascertain the action of each of the other two species. Intensity-time curves, variation of voltage between the electrodes, vapour diffusion through the electrode wall, load depletion, reaction products formation, and temperature, electron pressure and ionization degree in the are plasma have been studied. The measurement of plasma parameters has been performed by introducing thermometric and manometric species in both the anode and the cathode electrodes. A procedure for calculating the relative emission efficiencies of the analytical lines, taking into account the transportation process, has been developed. (Author) 21 refs

Volatilization-excitation phenomena and efficiency of spectrochemical buffers in the analysis of geological samples. I. The action of the mixture Li2CO3: graphite

International Nuclear Information System (INIS)

Diaz-Guerra, J.P.; Roca, M.

1984-01-01

The volatilization-excitation mechanisms of Li 2 CO 3 , SrCO 3 and GeO 2 as buffers for the determination of different major constituents in geological samples have been investigated considering the phenomena taking place in the electrode, anodic load and arc plasma. The present paper deals with the evaluation of fundamental parameters and processes in d.c. arc that have first been applied to the study of a Li 2 CO 3 : graphite (1:1) mixture. A second paper is devoted to ascertain the action of each of the other two species. Intensity-time curves, variation of voltage between the electrodes, vapour diffusion through the electrode wall, load depletion, reaction products formation, and temperature, electron pressure and ionization degree in the arc plasma have been studied. The measurement of plasma parameters has been performed by introducing thermometric and manometric species in both the anode and the cathode electrodes. A procedure for calculating the relative emission efficiencies of the analytical lines, taking into account the transportation process, has been developed. (author)

A novel highly efficient adsorbent {[Co4(L)2(μ3-OH)2(H2O)3(4,4‧-bipy)2]·(H2O)2}n: Synthesis, crystal structure, magnetic and arsenic (V) absorption capacity

Science.gov (United States)

Zhang, Chong; Xiao, Yu; Qin, Yan; Sun, Quanchun; Zhang, Shuhua

2018-05-01

A novel highly efficient adsorbent-microporous tetranuclear Co(II)-based polymer, {[Co4(L)2(μ3-OH)2(H2O)3(4,4‧-bipy)2]·(H2O)2}n (1, H3L = 4-(N,N‧-bis(4-carboxybenzyl)amino) benzenesulfonic acid, 4,4‧-bipy = 4,4‧-bipyridine), was hydrothermally synthesized. The complex 1 is a metal-organic framework (MOF) material which was characterized by single-crystal X-ray diffraction, BET and platon software. Co-MOF (complex 1) reveals excellent adsorption property. The capacity of Co-MOF to remove arsenic As(V) from sodium arsenate aqueous solutions was investigated (The form of As(V) is AsO43-). The experimental results showed that Co-MOF had a higher stable and relatively high As(V) removal rate (> 98%) at pH 4-10. The adsorption kinetics followed a pseudo-second-order kinetic model, and the adsorption isotherm followed the Langmuir equation. Co-MOF exhibits a very high adsorption capacity of As(V) in aqueous solution (Qmax of 96.08 mg/g). Finally, the optimal adsorption conditions for the model were obtained through a Box-Behnken response surface experiment which was designed with adsorption time, dose, temperature and rotational speed of the shaker as the influencing factors to determine two-factor interaction effects. Co-MOF was further characterized using FTIR, PXRD, X-ray photoelectron spectroscopy before and after adsorption As (V). The magnetism of Co-MOF was also discussed.

[Prediction of common buffer catalysis in hydrolysis of fenchlorazole-ethyl].

Science.gov (United States)

Lin, Jing; Chen, Jing-wen; Zhang, Si-yu; Cai, Xi-yun; Qiao, Xian-liang

2008-09-01

The purpose of this study was to elucidate the effects of temperatures, pH levels and buffer catalysis on the hydrolysis of FCE. The hydrolysis of FCE follows first-order kinetics at different pH levels and temperatures. FCE hydrolysis rates are greatly increased at elevated pH levels and temperatures. The maximum contribution of buffer catalysis to the hydrolysis of FCE was assessed based on application of the Bronsted equations for general acid-base catalysis. The results suggest that the buffer solutions play an obvious catalysis role in hydrolysis of FCE and the hydrolysis rates of FCE are quickened by the buffer solutions. Besides, the buffer catalysis capacity of different buffer solutions is diverse, and the buffer catalysis capacity at different pH levels with the same buffer solutions is different, too. The phosphate buffer at pH = 7 shows the maximal buffer catalysis capacity. The hydrolysis rate constants of FCE as a function of temperature and pH, which were remedied by the buffer catalysis factor, were mathematically combined to predict the hydrolytic dissipation of FCE. The equation suggests that the hydrolysis half-lives of FCE ranged from 7 d to 790 d. Hydrolysis metabolites of FCE were identified by liquid chromatography-mass spectrometry. In basic conditions (pH 8-10), fenchlorazole was formed via breakdown of the ester bond of the safener.

Coupled Ca2+/H+ transport by cytoplasmic buffers regulates local Ca2+ and H+ ion signaling.

Science.gov (United States)

Swietach, Pawel; Youm, Jae-Boum; Saegusa, Noriko; Leem, Chae-Hun; Spitzer, Kenneth W; Vaughan-Jones, Richard D

2013-05-28

Ca(2+) signaling regulates cell function. This is subject to modulation by H(+) ions that are universal end-products of metabolism. Due to slow diffusion and common buffers, changes in cytoplasmic [Ca(2+)] ([Ca(2+)]i) or [H(+)] ([H(+)]i) can become compartmentalized, leading potentially to complex spatial Ca(2+)/H(+) coupling. This was studied by fluorescence imaging of cardiac myocytes. An increase in [H(+)]i, produced by superfusion of acetate (salt of membrane-permeant weak acid), evoked a [Ca(2+)]i rise, independent of sarcolemmal Ca(2+) influx or release from mitochondria, sarcoplasmic reticulum, or acidic stores. Photolytic H(+) uncaging from 2-nitrobenzaldehyde also raised [Ca(2+)]i, and the yield was reduced following inhibition of glycolysis or mitochondrial respiration. H(+) uncaging into buffer mixtures in vitro demonstrated that Ca(2+) unloading from proteins, histidyl dipeptides (HDPs; e.g., carnosine), and ATP can underlie the H(+)-evoked [Ca(2+)]i rise. Raising [H(+)]i tonically at one end of a myocyte evoked a local [Ca(2+)]i rise in the acidic microdomain, which did not dissipate. The result is consistent with uphill Ca(2+) transport into the acidic zone via Ca(2+)/H(+) exchange on diffusible HDPs and ATP molecules, energized by the [H(+)]i gradient. Ca(2+) recruitment to a localized acid microdomain was greatly reduced during intracellular Mg(2+) overload or by ATP depletion, maneuvers that reduce the Ca(2+)-carrying capacity of HDPs. Cytoplasmic HDPs and ATP underlie spatial Ca(2+)/H(+) coupling in the cardiac myocyte by providing ion exchange and transport on common buffer sites. Given the abundance of cellular HDPs and ATP, spatial Ca(2+)/H(+) coupling is likely to be of general importance in cell signaling.

Enhancement in CO2 Adsorption Capacity and Selectivity in the Chalcogenide Aerogel CuSb2S4 by Post-synthetic Modification with LiCl

KAUST Repository

Ahmed, Ejaz; Rothenberger, Alexander

2015-01-01

The new chalcogel CuSb2S4 was obtained by reacting Cu(OAc)2·H2O with KSbS2 in a water/formamide mixture at room temperature. In order to modify the gas adsorption capacity the synthesized CuSb2S4 aerogel was loaded with different amounts of LiCl. CO

Elevated CO2 can modify the response to a water status gradient in a steppe grass: from cell organelles to photosynthetic capacity to plant growth.

Science.gov (United States)

Jiang, Yanling; Xu, Zhenzhu; Zhou, Guangsheng; Liu, Tao

2016-07-12

The atmospheric CO2 concentration is rising continuously, and abnormal precipitation may occur more frequently in the future. Although the effects of elevated CO2 and drought on plants have been well reported individually, little is known about their interaction, particularly over a water status gradient. Here, we aimed to characterize the effects of elevated CO2 and a water status gradient on the growth, photosynthetic capacity, and mesophyll cell ultrastructure of a dominant grass from a degraded grassland. Elevated CO2 stimulated plant biomass to a greater extent under moderate changes in water status than under either extreme drought or over-watering conditions. Photosynthetic capacity and stomatal conductance were also enhanced by elevated CO2 under moderate drought, but inhibited with over-watering. Severe drought distorted mesophyll cell organelles, but CO2 enrichment partly alleviated this effect. Intrinsic water use efficiency (WUEi) and total biomass water use efficiency (WUEt) were increased by elevated CO2, regardless of water status. Plant structural traits were also found to be tightly associated with photosynthetic potentials. The results indicated that CO2 enrichment alleviated severe and moderate drought stress, and highlighted that CO2 fertilization's dependency on water status should be considered when projecting key species' responses to climate change in dry ecosystems.

Earth 2075 (CO2) - can Ocean-Amplified Carbon Capture (oacc) Impart Atmospheric CO2-SINKING Ability to CCS Fossil Energy?

Science.gov (United States)

Fry, R.; Routh, M.; Chaudhuri, S.; Fry, S.; Ison, M.; Hughes, S.; Komor, C.; Klabunde, K.; Sethi, V.; Collins, D.; Polkinghorn, W.; Wroobel, B.; Hughes, J.; Gower, G.; Shkolnik, J.

2017-12-01

Previous attempts to capture atmospheric CO2 by algal blooming were stalled by ocean viruses, zooplankton feeding, and/or bacterial decomposition of surface blooms, re-releasing captured CO2 instead of exporting it to seafloor. CCS fossil energy coupling could bypass algal bloom limits—enabling capture of 10 GtC/yr atmospheric CO2 by selective emiliania huxleyi (EHUX) blooming in mid-latitude open oceans, far from coastal waters and polar seas. This could enable a 500 GtC drawdown, 350 ppm restoration by 2050, 280 ppm CO2 by 2075, and ocean pH 8.2. White EHUX blooms could also reflect sunlight back into outer space and seed extra ocean cloud cover, via DMS release, to raise albedo 1.8%—restoring preindustrial temperature (ΔT = 0°C) by 2030. Open oceans would avoid post-bloom anoxia, exclusively a coastal water phenomenon. The EHUX calcification reaction initially sources CO2, but net sinking prevails in follow-up equilibration reactions. Heavier-than-water EHUX sink captured CO2 to the sea floor before surface decomposition occurs. Seeding EHUX high on their nonlinear growth curve could accelerate short-cycle secondary open-ocean blooming—overwhelming mid-latitude viruses, zooplankton, and competition from other algae. Mid-latitude "ocean deserts" exhibit low viral, zooplankton, and bacterial counts. Thermocline prevents nutrient upwelling that would otherwise promote competing algae. Adding nitrogen nutrient would foster exclusive EHUX blooming. Elevated EHUX seed levels could arise from sealed, pH-buffered, floating, seed-production bioreactors infused with 10% CO2 from carbon feedstock supplied by inland CCS fossil power plants capturing 90% of emissions as liquid CO2. Deep-water SPAR platforms extract natural gas from beneath the sea floor. On-platform Haber and pH processing could convert extracted CH4 to buffered NH4+ nutrient, enabling ≥0.7 GtC/yr of bioreactor seed production and 10 GtC/yr of amplified secondary open-ocean CO2 capture—making CCS

A Low Cost, High Capacity Regenerable Sorbent for Pre-combustion CO{sub 2} Capture

Energy Technology Data Exchange (ETDEWEB)

Alptekin, Gokhan

2012-09-30

The overall objective of the proposed research is to develop a low cost, high capacity CO{sub 2} sorbent and demonstrate its technical and economic viability for pre-combustion CO{sub 2} capture. The specific objectives supporting our research plan were to optimize the chemical structure and physical properties of the sorbent, scale-up its production using high throughput manufacturing equipment and bulk raw materials and then evaluate its performance, first in bench-scale experiments and then in slipstream tests using actual coal-derived synthesis gas. One of the objectives of the laboratory-scale evaluations was to demonstrate the life and durability of the sorbent for over 10,000 cycles and to assess the impact of contaminants (such as sulfur) on its performance. In the field tests, our objective was to demonstrate the operation of the sorbent using actual coal-derived synthesis gas streams generated by air-blown and oxygen-blown commercial and pilot-scale coal gasifiers (the CO{sub 2} partial pressure in these gas streams is significantly different, which directly impacts the operating conditions hence the performance of the sorbent). To support the field demonstration work, TDA collaborated with Phillips 66 and Southern Company to carry out two separate field tests using actual coal-derived synthesis gas at the Wabash River IGCC Power Plant in Terre Haute, IN and the National Carbon Capture Center (NCCC) in Wilsonville, AL. In collaboration with the University of California, Irvine (UCI), a detailed engineering and economic analysis for the new CO{sub 2} capture system was also proposed to be carried out using Aspen PlusTM simulation software, and estimate its effect on the plant efficiency.

[Meeting point Stewart. Buffer bases, base excess and strong ions].

Science.gov (United States)

Lang, W

2007-04-01

Development of a two-buffer model which simulates the acid-base properties of blood and allows comparison of the different acidbase concepts according to Stewart and to Siggaard-Andersen. The two-buffer model consisted of different aqueous solutions of bicarbonate/CO(2) (pCO(2), sCO(2), pK(1)), HEPES buffer (A(tot), pK(a)) and electrolytes. These were used to calculate the pH from the independent variables according to Stewart - strong ion difference (SID), pCO(2) and total concentration of the weak acids (A(tot)) - from which all other dependent variables (cHCO(3)(-), cA(-), BB, BE) were obtained and compared with the measured values. The normal pH (7.408) was calculated from the normal values for SID (48 mmol/l), pCO(2) (40 mmHg) and A(tot) (45.2 mmol/l) and agreed perfectly with the measured value (7.409+/-0.001). This was also valid for all calculated and measured pH values when the SID was varied: non-respiratory alkalosis ( upward arrow) or acidosis ( downward arrow), pCO(2):respiratory acidosis ( upward arrow) or alkalosis ( downward arrow) and A(tot):hyperproteinemic acidosis ( upward arrow) or hypoproteinemic alkalosis ( downward arrow) were varied and the sum of the buffer bases (BB) was always equal to the SID. All changes and hence BE were also equal, providing that A(tot) was normal. This was not the case, however, if A(tot) was outside the normal range, when BE was then the difference from the normal BB at the respective reference point. Whereas the deviation of the measured pCO(2) was acceptable (1.74+/-0.86 mmHg), this was not the case for the SID (-6.18+/-3.58 mmol/l) calculated from the measured ion concentrations (Na, K, Ca, Cl). Despite controversial discussions, both concepts are much closer than might be expected. Whereas in the Stewart approach the focus of analysis is on plasma, with the Siggaard-Andersen approach it is on blood. Hence, a combined analysis of the blood gases (pH, pCO(2), pO(2), sO(2), cHb, BE) and of the strong ion gap (SIG

Promoting Ethylene Selectivity from CO2 Electroreduction on CuO Supported onto CO2 Capture Materials.

Science.gov (United States)

Yang, Hui-Juan; Yang, Hong; Hong, Yu-Hao; Zhang, Peng-Yang; Wang, Tao; Chen, Li-Na; Zhang, Feng-Yang; Wu, Qi-Hui; Tian, Na; Zhou, Zhi-You; Sun, Shi-Gang

2018-03-09

Cu is a unique catalyst for CO 2 electroreduction, since it can catalyze CO 2 reduction to a series of hydrocarbons, alcohols, and carboxylic acids. Nevertheless, such Cu catalysts suffer from poor selectivity. High pressure of CO 2 is considered to facilitate the activity and selectivity of CO 2 reduction. Herein, a new strategy is presented for CO 2 reduction with improved C 2 H 4 selectivity on a Cu catalyst by using CO 2 capture materials as the support at ambient pressure. N-doped carbon (N x C) was synthesized through high-temperature carbonization of melamine and l-lysine. We observed that the CO 2 uptake capacity of N x C depends on both the microporous area and the content of pyridinic N species, which can be controlled by the carbonization temperature (600-800 °C). The as-prepared CuO/N x C catalysts exhibit a considerably higher C 2 H 4 faradaic efficiency (36 %) than CuO supported on XC-72 carbon black (19 %), or unsupported CuO (20 %). Moreover, there is a good linear relationship between the C 2 H 4 faradaic efficiency and CO 2 uptake capacity of the supports for CuO. The local high CO 2 concentration near Cu catalysts, created by CO 2 capture materials, was proposed to increase the coverage of CO intermediate, which is favorable for the coupling of two CO units in the formation of C 2 H 4 . This study demonstrates that pairing Cu catalysts with CO 2 capture supports is a promising approach for designing highly effective CO 2 reduction electrocatalysts. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Efficient small-molecule organic solar cells incorporating a doped buffer layer

Energy Technology Data Exchange (ETDEWEB)

Chou, Dei-Wei [Department of aviation and Communication Electronics, Air Force Institute of Technology, Kaohsiung 820, Taiwan (China); Chen, Kan-Lin [Department of Electronic Engineering, Fortune Institute of Technology, Kaohsiung 831, Taiwan (China); Huang, Chien-Jung, E-mail: chien@nuk.edu.tw [Department of Applied Physics, National University of Kaohsiung, Nanzih, Kaohsiung 811, Taiwan (China); Tsao, Yao-Jen [Department of Applied Physics, National University of Kaohsiung, Nanzih, Kaohsiung 811, Taiwan (China); Chen, Wen-Ray; Meen, Teen-Hang [Department of Electronic Engineering, National Formosa University, Hu-Wei, Yunlin 632, Taiwan (China)

2013-06-01

Small-molecule organic solar cells (OSCs) with an optimized structure of indium tin oxide/poly (3,4-ethylenedioxythioxythiophene):poly(styrenesulfonate)/copper phthalocyanine (CuPc) (10 nm)/CuPc: fullerene (C{sub 60}) mixed (20 nm)/C{sub 60} (20 nm)/4,7-diphenyl-1,10-phenanthroline (BPhen) (5 nm)/Ag were fabricated. In this study, the cesium carbonate-doped BPhen (Cs{sub 2}CO{sub 3}:BPhen) was adopted as the buffer layer to enhance the efficiency of the OSCs. The photovoltaic parameters of the OSCs, such as the short-circuit current density and fill factor, depend on the doping concentration of Cs{sub 2}CO{sub 3} in the BPhen layer. The cell with a Cs{sub 2}CO{sub 3}:BPhen (1:4) cathode buffer layer exhibits a power conversion efficiency (PCE) of 3.51%, compared to 3.37% for the device with the pristine BPhen layer. The enhancement of PCE was attributed to the energy-level alignment between the C{sub 60} layer and the Cs{sub 2}CO{sub 3}:BPhen layer. In addition, the characterization measured using atomic force microscopy shows that the Cs{sub 2}CO{sub 3}:BPhen layers have smoother surfaces. - Highlight: • Cs2CO3-doped 4,7-diphenyl-1,10-phenanthroline (BPhen) cathode buffer layer. • Cs2CO3:BPhen layer with different ratios affects organic solar cells performance. • Cell with 1:4 (Cs2CO3:BPhen) ratio shows 3.51% power conversion efficiency.

CoFe2O4@MIL-100(Fe) hybrid magnetic nanoparticles exhibit fast and selective adsorption of arsenic with high adsorption capacity

Science.gov (United States)

Yang, Ji-Chun; Yin, Xue-Bo

2017-01-01

In this study, we report the synthesis and application of mesoporous CoFe2O4@MIL-100(Fe) hybrid magnetic nanoparticles (MNPs) for the simultaneous removal of inorganic arsenic (iAs). The hybrid adsorbent had a core-shell and mesoporous structure with an average diameter of 260 nm. The nanoscale size and mesoporous character impart a fast adsorption rate and high adsorption capacity for iAs. In total, 0.1 mg L−1 As(V) and As(III) could be adsorbed within 2 min, and the maximum adsorption capacities were 114.8 mg g−1 for As(V) and 143.6 mg g−1 for As(III), higher than most previously reported adsorbents. The anti-interference capacity for iAs adsorption was improved by the electrostatic repulsion and size exclusion effects of the MIL-100(Fe) shell, which also decreased the zero-charge point of the hybrid absorbent for a broad pH adsorption range. The adsorption mechanisms of iAs on the MNPs are proposed. An Fe-O-As structure was formed on CoFe2O4@MIL-100(Fe) through hydroxyl substitution with the deprotonated iAs species. Monolayer adsorption of As(V) was observed, while hydrogen bonding led to the multi-layer adsorption of neutral As(III) for its high adsorption capacity. The high efficiency and the excellent pH- and interference-tolerance capacities of CoFe2O4@MIL-100(Fe) allowed effective iAs removal from natural water samples, as validated with batch magnetic separation mode and a portable filtration strategy. PMID:28102334

3-dimensional porous NiCo2O4 nanocomposite as a high-rate capacity anode for lithium-ion batteries

International Nuclear Information System (INIS)

Mo, Yudi; Ru, Qiang; Song, Xiong; Hu, Shejun; Guo, Lingyun; Chen, Xiaoqiu

2015-01-01

Highlights: • D-glucose molecules as organic carbon source, have a crucial effect on the morphology and pore distribution of the synthetic products. • Facile synthesis: solvothermal method. • High rate capacity: 625 mAh g −1 at 4.4 C. • Improved long-term cycling stability: 1389 mAh g −1 after 180 cycles at 0.55 C. - Abstract: In this work, organic carbon modified NiCo 2 O 4 (NCO@C) nanocomposite with porous 3-dimensional (3D) structure was successfully synthesized by a facile hydrothermal method in D-glucose-mediated processes. A detailed research reveals that D-glucose molecules play an important role in the formation of the porous 3D structure and also provide a conductive carbon network within the NCO@C nanocomposite materials. Such a porous 3D interconnected carbonaceous nanostructure applied as electrode material for lithium-ion batteries (LIBs) shows that its reversible capacity, cycling stability, and rate capability are significantly enhanced in comparison with those of pure NiCo 2 O 4 (NCO) electrode. The as-prepared NCO@C composite electrode with porous 3D nanostructure displays a higher discharge specific capacity of 1389 mAh g −1 even after 180 cycles at a current rate of 0.55 C. Furthermore, this composite material also presents a high rate capacity, when the current rate gradually increases to 0.55 C, 1.1 C, 2.2 C, and 4.4 C, the reversible capacity can still render about 1082, 1029, 850, and 625 mAh g −1 , respectively. The enhanced electrochemical performance indicated that the NCO@C nanocomposite might be a very promising candidate to replace conventional graphite-based anode materials for LIBs

Mesoporous carbon composite for CO{sub 2} capture

Energy Technology Data Exchange (ETDEWEB)

Hwang, Chih-Chau; Jin, Zhong; Lu, Wei; Sun, Zhengzong; Alemany, Lawrence; Tour, James M. [Rice University, Houston, TX (United States); Lomeda, Jay R.; Flatt, Austen K. [Nalco Company, Naperville, IL (United States)

2012-07-01

Herein we report a carbon based technology that can be used to rapidly adsorb and release CO{sub 2}. CO{sub 2} uptake by the synthesized composites was determined using a gravimetric method at room temperature and atmospheric pressure. 39% polyethylenimine-mesocarbon (PEI-CMK-3) composite had {approx} 12 wt% CO{sub 2} uptake capacity and a 37% polyvinylamine meso-carbon (PVA-CMK-3) composite had {approx} 13 wt% CO{sub 2} uptake capacity. The sorbents were easily regenerated at 75 deg C and exhibit excellent stability over multiple regeneration cycles. CO{sub 2} uptake was equivalent when using 10% CO{sub 2} in 90% CH{sub 4}, C{sub 2}H{sub 6} and C{sub 3}H{sub 9} mixture, underscoring the efficacy for CO{sub 2} separation from natural gas. (author)

Synthesis of NiPS3 and CoPS and its hydrogen storage capacity

International Nuclear Information System (INIS)

Ismail, N.; Madian, M.; El-Meligi, A.A.

2014-01-01

Highlights: • Preparation of NiPS 3 and CoPS using solid state reaction. • Characterization of compounds using XRD, TEM, SEM and IR. • Measuring the compounds thermal stability. • Estimation of the hydrogen storage capacity. -- Abstract: Prepared CoPS and NiPS 3 are studied as new materials for hydrogen energy storage. Single phase of CoPS and NiPS 3 were grown separately in evacuated silicatube via solid state reaction at 650 °C with controlled heating rate 1 °C/min. X-ray diffraction patterns confirm the formation of the desired compounds. Both CoPS and NiPS 3 exhibited high thermal stability up to 700 °C and 630 °C, respectively. The morphology of the prepared samples was investigated using scanning electron microscopy and folded sheets appeared in the transmission electron microscopy. The samples were exposed to 20 bar applied hydrogen pressure at 80 K. Both compounds appear to have feasible hydrogen storage capacity. CoPS was capable to adsorb 1.7 wt% while NiPS 3 storage capacity reached 1.2 wt%

The buffering-out effect and phase separation in aqueous solutions of EPPS buffer with 1-propanol, 2-propanol, or 2-methyl-2-propanol at T = 298.15 K

International Nuclear Information System (INIS)

Taha, Mohamed; Teng, Han-Lan; Lee, Ming-Jer

2012-01-01

Highlights: ► Buffering-out is a new liquid–liquid phase separation containing biological buffer. ► EPPS buffer-induced phase separation of aqueous solutions of aliphatic alcohols. ► Phase diagrams of EPPS + water + 1-propanol/2-propanol/2-methyl-2-propanol are studied. ► EPPS breaks the 1-propanol + water and 2-methyl-2-propanol + water azeotropes. ► The (liquid + liquid) equilibria can be well correlated by the NRTL model. - Abstract: Buffering-out is a new liquid–liquid phase separation phenomenon observed in mixtures containing a buffer as a mass separating agent. The (liquid + liquid) equilibrium (LLE) and (solid + liquid + liquid) equilibrium (SLLE) data were measured for the ternary systems {3-[4-(2-hydroxyethyl)piperazin-1-yl]propanesulfonic acid (EPPS) buffer + 1-propanol, 2-propanol, or 2-methyl-2-propanol + water} at T = 298.15 K under atmospheric pressure. The phase boundary data were fitted to an empirical equation relating to the concentrations of organic solvent and buffer. The effective excluded volume (EEV) values of EPPS were obtained from the phase boundary data. The phase-separation abilities of the investigated aliphatic alcohols were discussed. The reliability of the experimental tie-lines was satisfactorily confirmed by the Othmer–Tobias correlation. The experimental tie-lines data for the ternary systems have been correlated using the NRTL activity coefficient model. The separation of these aliphatic alcohols from their azeotropic aqueous mixtures is of particular interest to industrial process. The addition of the EPPS as an auxiliary agent breaks the (1-propanol + water) and (2-methyl-2-propanol + water) azeotropes. The possibility of using the new phase separation systems in the extraction process is demonstrated by using different dyestuffs.

CaCO3 supplementation alleviates the inhibition of formic acid on acetone/butanol/ethanol fermentation by Clostridium acetobutylicum.

Science.gov (United States)

Qi, Gaoxiang; Xiong, Lian; Lin, Xiaoqing; Huang, Chao; Li, Hailong; Chen, Xuefang; Chen, Xinde

2017-01-01

To investigate the inhibiting effect of formic acid on acetone/butanol/ethanol (ABE) fermentation and explain the mechanism of the alleviation in the inhibiting effect under CaCO 3 supplementation condition. From the medium containing 50 g sugars l -1 and 0.5 g formic acid l -1 , only 0.75 g ABE l -1 was produced when pH was adjusted by KOH and fermentation ended prematurely before the transformation from acidogenesis to solventogenesis. In contrast, 11.4 g ABE l -1 was produced when pH was adjusted by 4 g CaCO 3 l -1 . The beneficial effect can be ascribed to the buffering capacity of CaCO 3 . Comparative analysis results showed that the undissociated formic acid concentration and acid production coupled with ATP and NADH was affected by the pH buffering capacity of CaCO 3 . Four millimole undissociated formic acid was the threshold at which the transformation to solventogenesis occurred. The inhibiting effect of formic acid on ABE fermentation can be alleviated by CaCO 3 supplementation due to its buffering capacity.

Buffer-regulated biocorrosion of pure magnesium.

Science.gov (United States)

Kirkland, Nicholas T; Waterman, Jay; Birbilis, Nick; Dias, George; Woodfield, Tim B F; Hartshorn, Richard M; Staiger, Mark P

2012-02-01

Magnesium (Mg) alloys are being actively investigated as potential load-bearing orthopaedic implant materials due to their biodegradability in vivo. With Mg biomaterials at an early stage in their development, the screening of alloy compositions for their biodegradation rate, and hence biocompatibility, is reliant on cost-effective in vitro methods. The use of a buffer to control pH during in vitro biodegradation is recognised as critically important as this seeks to mimic pH control as it occurs naturally in vivo. The two different types of in vitro buffer system available are based on either (i) zwitterionic organic compounds or (ii) carbonate buffers within a partial-CO(2) atmosphere. This study investigated the influence of the buffering system itself on the in vitro corrosion of Mg. It was found that the less realistic zwitterion-based buffer did not form the same corrosion layers as the carbonate buffer, and was potentially affecting the behaviour of the hydrated oxide layer that forms on Mg in all aqueous environments. Consequently it was recommended that Mg in vitro experiments use the more biorealistic carbonate buffering system when possible.

CO2 capture by ionic liquids - an answer to anthropogenic CO2 emissions?

Science.gov (United States)

Sanglard, Pauline; Vorlet, Olivier; Marti, Roger; Naef, Olivier; Vanoli, Ennio

2013-01-01

Ionic liquids (ILs) are efficient solvents for the selective removal of CO2 from flue gas. Conventional, offthe-shelf ILs are limited in use to physisorption, which restricts their absorption capacity. After adding a chemical functionality like amines or alcohols, absorption of CO2 occurs mainly by chemisorption. This greatly enhances CO2 absorption and makes ILs suitable for potential industrial applications. By carefully choosing the anion and the cation of the IL, equimolar absorption of CO2 is possible. This paper reviews the current state of the art of CO2 capture by ILs and presents the current research in this field performed at the ChemTech Institute of the Ecole d'Ingénieurs et d'Architectes de Fribourg.

Stability and buffering capacity of the geosphere for long-term isolation of radioactive waste

International Nuclear Information System (INIS)

2004-01-01

Most experts worldwide agree that radioactive waste disposal in engineered facilities, or repositories, located in appropriate formations deep underground, provide a suitable waste management option for protecting humans and the environment now and. in the future. An NEA workshop was organised on 9-11 December 2003 in Braunschweig, Germany, devoted specifically to argillaceous settings for deep geological repositories. The workshop brought together scientists from academic institutions, engineers from various research institutions or companies, consultants, regulatory authorities and national waste management organisations to establish the scientific basis for stability and buffering capacity of deep geological waste management systems. The present report synthesizes the main outcomes of that workshop and presents a compilation of the related abstracts. (author)

Effect of buffer general acid-base catalysis on the stereoselectivity of ester and thioester H/D exchange in D2O.

Science.gov (United States)

Mohrig, Jerry R; Reiter, Nicholas J; Kirk, Randy; Zawadski, Michelle R; Lamarre-Vincent, Nathan

2011-04-06

As part of a comprehensive investigation on the stereochemistry of base-catalyzed 1,2-elimination and H/D exchange reactions of carbonyl compounds, we have found that the stereoselectivity of H/D exchange of 3-hydroxybutyryl N-acetylcysteamine (3) in D(2)O is strongly influenced by the presence of buffers. This buffer effect is also operative with a simple acyclic ester, ethyl 3-methoxybutanoate (7). Buffers whose general-acid components are cyclic tertiary ammonium ions are particularly effective in changing the stereoselectivity. (2)H NMR analysis showed that without buffer, H/D exchange of 3 produces 81-82% of the 2R*, 3R* diastereomer of 2-deuterio 3 (the anti product). In the presence of 0.33 M 3-quinuclidinone buffer, only 44% of the 2R*, 3R* diastereomer was formed. With ester 7, the stereoselectivity went from 93-94% in DO(-)/D(2)O to 60% in the presence of buffer. Phosphate buffer, as well as others, also showed substantial effects. The results are put into the context of what is known about the mechanism of H/D exchange of esters and thioesters, and the relevance of the buffer effect on the mechanism of the enoyl-CoA hydratase reaction is discussed. It is likely that hydrogen bonding in the enolate-buffer acid encounter complex is an important stereochemical determinant in producing a greater amount of the 2R*, 3S* diastereomer (the syn product). Studies that involve the protonation of enolate anions in D(2)O need to include the buffer general acid in any understanding of the stereoselectivity. © 2011 American Chemical Society

Future ocean hypercapnia driven by anthropogenic amplification of the natural CO2 cycle

Science.gov (United States)

McNeil, Ben I.; Sasse, Tristan P.

2016-01-01

High carbon dioxide (CO2) concentrations in sea-water (ocean hypercapnia) can induce neurological, physiological and behavioural deficiencies in marine animals. Prediction of the onset and evolution of hypercapnia in the ocean requires a good understanding of annual variations in oceanic CO2 concentration, but there is a lack of relevant global observational data. Here we identify global ocean patterns of monthly variability in carbon concentration using observations that allow us to examine the evolution of surface-ocean CO2 levels over the entire annual cycle under increasing atmospheric CO2 concentrations. We predict that the present-day amplitude of the natural oscillations in oceanic CO2 concentration will be amplified by up to tenfold in some regions by 2100, if atmospheric CO2 concentrations continue to rise throughout this century (according to the RCP8.5 scenario of the Intergovernmental Panel on Climate Change). The findings from our data are broadly consistent with projections from Earth system climate models. Our predicted amplification of the annual CO2 cycle displays distinct global patterns that may expose major fisheries in the Southern, Pacific and North Atlantic oceans to hypercapnia many decades earlier than is expected from average atmospheric CO2 concentrations. We suggest that these ocean ‘CO2 hotspots’ evolve as a combination of the strong seasonal dynamics of CO2 concentration and the long-term effective storage of anthropogenic CO2 in the oceans that lowers the buffer capacity in these regions, causing a nonlinear amplification of CO2 concentration over the annual cycle. The onset of ocean hypercapnia (when the partial pressure of CO2 in sea-water exceeds 1,000 micro-atmospheres) is forecast for atmospheric CO2 concentrations that exceed 650 parts per million, with hypercapnia expected in up to half the surface ocean by 2100, assuming a high-emissions scenario (RCP8.5). Such extensive ocean hypercapnia has detrimental implications for

Buffer sizing for multi-hop networks

KAUST Repository

Shihada, Basem

2014-01-28

A cumulative buffer may be defined for an interference domain in a wireless mesh network and distributed among nodes in the network to maintain or improve capacity utilization of network resources in the interference domain without increasing packet queuing delay times. When an interference domain having communications links sharing resources in a network is identified, a cumulative buffer size is calculated. The cumulative buffer may be distributed among buffers in each node of the interference domain according to a simple division or according to a cost function taking into account a distance of the communications link from the source and destination. The network may be monitored and the cumulative buffer size recalculated and redistributed when the network conditions change.

High temperature CO2 capture of hydroxyapatite extracted from tilapia scales

Directory of Open Access Journals (Sweden)

Oscar H. Ojeda-Niño

2017-11-01

Full Text Available Hydroxyapatite (HAp was obtained from tilapia scales by two extraction methods: direct calcination and acid-base treatment. The physicochemical characteristics of the obtained HAps were evaluated by thermogravimetric analysis, X-ray fluorescence, X-ray diffraction, scanning electron microscopy, surface area, infrared spectroscopy, and basicity measurement at 298 K by CO2-pulse titration. Furthermore, the CO2 capture capacity of the solids at high temperature was also determined. Both methods showed the presence of a HAp phase although significant differences in the properties of the solids were found. The HAp obtained by direct calcination exhibited a lower crystallinity and a greater surface area and basicity than the HAp obtained by the acid-base treatment. These features were correlated with the solid’s CO2 capture capacity. In this work, CO2 capture capacity values for HAp yielded by calcination ranged from 2.5 to 3.2 mg CO2 /g captured at 973 K, and for the acid-base treatment-derived HAp, CO2 capture capacity values between 1.2 to 2.5 mg CO2 /g were recorded. These results reveal the potential of HAps extracted from tilapia scales as solids with high CO2 capture capacity, thermal stability, and capture/release cycles reversibility.

Synthesis of Co/MFe(2)O(4) (M = Fe, Mn) Core/Shell Nanocomposite Particles.

Science.gov (United States)

Peng, Sheng; Xie, Jin; Sun, Shouheng

2008-01-01

Monodispersed cobalt nanoparticles (NPs) with controllable size (8-14 nm) have been synthesized using thermal decomposition of dicobaltoctacarbonyl in organic solvent. The as-synthesized high magnetic moment (125 emu/g) Co NPs are dispersible in various organic solvents, and can be easily transferred into aqueous phase by surface modification using phospholipids. However, the modified hydrophilic Co NPs are not stable as they are quickly oxidized, agglomerated in buffer. Co NPs are stabilized by coating the MFe(2)O(4) (M = Fe, Mn) ferrite shell. Core/shell structured bimagnetic Co/MFe(2)O(4) nanocomposites are prepared with tunable shell thickness (1-5 nm). The Co/MFe(2)O(4) nanocomposites retain the high magnetic moment density from the Co core, while gaining chemical and magnetic stability from the ferrite shell. Comparing to Co NPs, the nanocomposites show much enhanced stability in buffer solution at elevated temperatures, making them promising for biomedical applications.

Porous Organic Polymers for CO2 Capture

KAUST Repository

Teng, Baiyang

2013-05-01

Carbon dioxide (CO2) has long been regarded as the major greenhouse gas, which leads to numerous negative effects on global environment. The capture and separation of CO2 by selective adsorption using porous materials proves to be an effective way to reduce the emission of CO2 to atmosphere. Porous organic polymers (POPs) are promising candidates for this application due to their readily tunable textual properties and surface functionalities. The objective of this thesis work is to develop new POPs with high CO2 adsorption capacities and CO2/N2 selectivities for post-combustion effluent (e.g. flue gas) treatment. We will also exploit the correlation between the CO2 capture performance of POPs and their textual properties/functionalities. Chapters Two focuses on the study of a group of porous phenolic-aldehyde polymers (PPAPs) synthesized by a catalyst-free method, the CO2 capture capacities of these PPAPs exceed 2.0 mmol/g at 298 K and 1 bar, while keeping CO2/N2 selectivity of more than 30 at the same time. Chapter Three reports the gas adsorption results of different hyper-cross-linked polymers (HCPs), which indicate that heterocyclo aromatic monomers can greatly enhance polymers’ CO2/N2 selectivities, and the N-H bond is proved to the active CO2 adsorption center in the N-contained (e.g. pyrrole) HCPs, which possess the highest selectivities of more than 40 at 273 K when compared with other HCPs. Chapter Four emphasizes on the chemical modification of a new designed polymer of intrinsic microporosity (PIM) with high CO2/N2 selectivity (50 at 273 K), whose experimental repeatability and chemical stability prove excellent. In Chapter Five, we demonstrate an improvement of both CO2 capture capacity and CO2/N2 selectivity by doping alkali metal ions into azo-polymers, which leads a promising method to the design of new porous organic polymers.

Development of Novel CO2 Adsorbents for Capture of CO2 from Flue Gas

Energy Technology Data Exchange (ETDEWEB)

Fauth, D.J.; Filburn, T.P. (University of Hartford, West Hartford, CT); Gray, M.L.; Hedges, S.W.; Hoffman, J.; Pennline, H.W.; Filburn, T.

2007-06-01

Capturing CO2 emissions generated from fossil fuel-based power plants has received widespread attention and is considered a vital course of action for CO2 emission abatement. Efforts are underway at the Department of Energy’s National Energy Technology Laboratory to develop viable energy technologies enabling the CO2 capture from large stationary point sources. Solid, immobilized amine sorbents (IAS) formulated by impregnation of liquid amines within porous substrates are reactive towards CO2 and offer an alternative means for cyclic capture of CO2 eliminating, to some degree, inadequacies related to chemical absorption by aqueous alkanolamine solutions. This paper describes synthesis, characterization, and CO2 adsorption properties for IAS materials previously tested to bind and release CO2 and water vapor in a closed loop life support system. Tetraethylenepentamine (TEPA), acrylonitrile-modified tetraethylenepentamine (TEPAN), and a single formulation consisting of TEPAN and N, N’-bis(2-hydroxyethyl)ethylenediamine (BED) were individually supported on a poly (methyl methacrylate) (PMMA) substrate and examined. CO2 adsorption profiles leading to reversible CO2 adsorption capacities were obtained using thermogravimetry. Under 10% CO2 in nitrogen at 25°C and 1 atm, TEPA supported on PMMA over 60 minutes adsorbed ~3.2 mmol/g{sorbent} whereas, TEPAN supported on PMMA along with TEPAN and BED supported on PMMA adsorbed ~1.7 mmol/g{sorbent} and ~2.3 mmol/g{sorbent} respectively. Cyclic experiments with a 1:1 weight ratio of TEPAN and BED supported on poly (methyl methacrylate) beads utilizing a fixed-bed flow system with 9% CO2, 3.5% O2, nitrogen balance with trace gas constituents were studied. CO2 adsorption capacity was ~ 3 mmols CO2/g{sorbent} at 40°C and 1.4 atm. No beneficial effect on IAS performance was found using a moisture-laden flue gas mixture. Tests with 750 ppmv NO in a humidified gas stream revealed negligible NO sorption onto the IAS. A high SO2

More on the losses of dissolved CO(2) during champagne serving: toward a multiparameter modeling.

Science.gov (United States)

Liger-Belair, Gérard; Parmentier, Maryline; Cilindre, Clara

2012-11-28

Pouring champagne into a glass is far from being inconsequential with regard to the dissolved CO(2) concentration found in champagne. Three distinct bottle types, namely, a magnum bottle, a standard bottle, and a half bottle, were examined with regard to their loss of dissolved CO(2) during the service of successively poured flutes. Whatever the bottle size, a decreasing trend is clearly observed with regard to the concentration of dissolved CO(2) found within a flute (from the first to the last one of a whole service). Moreover, when it comes to champagne serving, the bottle size definitely does matter. The higher the bottle volume, the better its buffering capacity with regard to dissolved CO(2) found within champagne during the pouring process. Actually, for a given flute number in a pouring data series, the concentration of dissolved CO(2) found within the flute was found to decrease as the bottle size decreases. The impact of champagne temperature (at 4, 12, and 20 °C) on the losses of dissolved CO(2) found in successively poured flutes for a given standard 75 cL bottle was also examined. Cold temperatures were found to limit the decreasing trend of dissolved CO(2) found within the successively poured flutes (from the first to the last one of a whole service). Our experimental results were discussed on the basis of a multiparameter model that accounts for the major physical parameters that influence the loss of dissolved CO(2) during the service of a whole bottle type.

A microporous MOF with a polar pore surface exhibiting excellent selective adsorption of CO2 from CO2-N2 and CO2-CH4 gas mixtures with high CO2 loading.

Science.gov (United States)

Pal, Arun; Chand, Santanu; Elahi, Syed Meheboob; Das, Madhab C

2017-11-14

A microporous MOF {[Zn(SDB)(L) 0.5 ]·S} n (IITKGP-5) with a polar pore surface has been constructed by the combination of a V-shaped -SO 2 functionalized organic linker (H 2 SDB = 4,4'-sulfonyldibenzoic acid) with an N-rich spacer (L = 2,5-bis(3-pyridyl)-3,4-diaza-2,4-hexadiene), forming a network with sql(2,6L1) topology. IITKGP-5 is characterized by TGA, PXRD and single crystal X-ray diffraction. The framework exhibits lozenge-shaped channels of an approximate size of 4.2 × 5.6 Å 2 along the crystallographic b axis with a potential solvent accessible volume of 26%. The activated IITKGP-5a revealed a CO 2 uptake capacity of 56.4 and 49 cm 3 g -1 at 273 K/1 atm and 295 K/1 atm, respectively. On the contrary, it takes up a much smaller amount of CH 4 (17 cm 3 g -1 at 273 K and 13.6 cm 3 g -1 at 295 K) and N 2 (5.5 cm 3 g -1 at 273 K; 4 cm 3 g -1 at 295 K) under 1 atm pressure exhibiting its potential for a highly selective adsorption of CO 2 from flue gas as well as a landfill gas mixture. Based on the ideal adsorbed solution theory (IAST), a CO 2 /N 2 selectivity of 435.5 and a CO 2 /CH 4 selectivity of 151.6 have been realized at 273 K/100 kPa. The values at 295 K are 147.8 for CO 2 /N 2 and 23.8 for CO 2 /CH 4 gas mixtures under 100 kPa. In addition, this MOF nearly approaches the target values proposed for PSA and TSA processes for practical utility exhibiting its prospect for flue gas separation with a CO 2 loading capacity of 2.04 mmol g -1 .

Heat buffers improve capacity and exploitation degree of geothermal energy sources

NARCIS (Netherlands)

Ooster, A.van t; Wit, J. de; Janssen, E.G.O.N.; Ruigrok, J.

2008-01-01

This research focuses on the role of heat buffers to support optimal use of combinations of traditional and renewable heat sources like geothermal heat for greenhouse heating. The objective was to determine the contribution of heat buffers to effective new combinations of resources that satisfy

The potential water buffering capacity of urban green infrastructure in an arid environment

Science.gov (United States)

Wang, Z.; Yang, J.

2017-12-01

Urban green infrastructure offers arid cities an attractive means of mitigation/adaptation to environmental challenges of elevated thermal stress, but imposes the requirement of outdoor irrigation that aggravates the stress of water resource management. Future development of cities is inevitably constrained by the limited availability of water resources, under challenges of emergent climate change and continuous population growth. This study used the Weather Research and Forecasting model with urban dynamics to assess the potential water buffering capacity of urban green infrastructure in arid environments and its implications for sustainable urban planning. The Phoenix metropolitan area, Arizona, United States, is adopted as a testbed with two hypothetical cases, viz. the water-saving and the fully-greening scenarios investigated. Modifications of the existing green infrastructure and irrigation practices are found to significantly influence the thermal environment of Phoenix. In addition, water saving by xeriscaping (0.77 ± 0.05 × 10^8 m^3) allows the region to support 19.8% of the annual water consumption by the projected 2.62 million population growth by 2050, at a cost of an increase in urban ambient temperature of about 1 o^C.

Buffering dissociation/formation reaction of biogenic calcium carbonate.

Science.gov (United States)

Ichikawa, Kazuhiko

2007-01-01

The oscillating stability of coral reef seawater pH has been maintained at around physiological pH values over the past 300 years (Pelejero et al., 2005). The stability mechanism of its pH has been interpreted in terms of the buffering dissolution/formation reaction of CaCO(3) as well as the proton consumption/generation reaction in CaCO(3)-saturated water. Here the pH-dependent solubility product [HCO(3)(-)][Ca(2+)] has been derived on the basis of the actual pH-dependent reactions for the atmospheric CO(2)/CO(2 (aq.))/HCO(3)(-)/CO(3)(2-)/Ca(2+)/CaCO(3) system. Overbasic pH peaks appeared between pH approximately 8 and approximately 9.5 during sodium hydroxide titration, as a result of simultaneous CaCO(3) formation and proton generation. The spontaneous and prompt water pH recovery from the acidic to the physiological range has been confirmed by the observation of acid/base time evolution, because of simultaneous CaCO(3) dissolution and proton consumption. The dissolution/formation of CaCO(3) in water at pH 7.5-9 does not take place without a proton consumption/generation reaction, or a buffering chemical reaction of HCO(3)(-)+Ca(2+)right arrow over left arrowCaCO(3)+H(+). SEM images of the CaCO(3) fragments showed that the acid water ate away at the CaCO(3) formed at physiological pH values. Natural coral reefs can thus recover the physiological pH levels of seawater from the acidic range through partial dissolution of their own skeletons.

Prediction of heat capacity of amine solutions using artificial neural network and thermodynamic models for CO2 capture processes

Science.gov (United States)

Afkhamipour, Morteza; Mofarahi, Masoud; Borhani, Tohid Nejad Ghaffar; Zanganeh, Masoud

2018-03-01

In this study, artificial neural network (ANN) and thermodynamic models were developed for prediction of the heat capacity ( C P ) of amine-based solvents. For ANN model, independent variables such as concentration, temperature, molecular weight and CO2 loading of amine were selected as the inputs of the model. The significance of the input variables of the ANN model on the C P values was investigated statistically by analyzing of correlation matrix. A thermodynamic model based on the Redlich-Kister equation was used to correlate the excess molar heat capacity ({C}_P^E) data as function of temperature. In addition, the effects of temperature and CO2 loading at different concentrations of conventional amines on the C P values were investigated. Both models were validated against experimental data and very good results were obtained between two mentioned models and experimental data of C P collected from various literatures. The AARD between ANN model results and experimental data of C P for 47 systems of amine-based solvents studied was 4.3%. For conventional amines, the AARD for ANN model and thermodynamic model in comparison with experimental data were 0.59% and 0.57%, respectively. The results showed that both ANN and Redlich-Kister models can be used as a practical tool for simulation and designing of CO2 removal processes by using amine solutions.

Role of histidine-related compounds to intracellular buffering in fish skeletal muscle.

Science.gov (United States)

Abe, H; Dobson, G P; Hoeger, U; Parkhouse, W S

1985-10-01

Histidine-related compounds (HRC) were analyzed in fish skeletal muscle as a means of identifying their precise role in intracellular buffering. Fish muscle was used because it contains two functionally and spatially distinct fiber types, red and white. Two fish species, rainbow trout (Salmo gairdneri) and the Pacific blue marlin (Makaira nigricans), were studied because these species demonstrate widely different activity patterns. Marlin red and white muscle buffer capacity was two times higher than trout with white muscle, buffering being two times greater than red in both species. Buffer capacity was highest in the 6.5-7.5 pH range for all tissues, which corresponded to their high anserine levels. The titrated HRC buffering was greater than the observed HRC buffering, which suggested that not all HRC were available to absorb protons. The HRC contribution to total cellular buffering varied from a high of 62% for marlin white to a low of 7% for trout red. The other principal buffers were found to be phosphate and protein with taurine contributing within red muscle in the 7.0-8.0 pH range. HRC were found to be dominant in skeletal muscle buffering by principally accounting for the buffering capacity differences found between the species and fiber types.

CO{sub 2} storage in saline aquifers; Stockage du CO{sub 2} dans les aquiferes salins

Energy Technology Data Exchange (ETDEWEB)

Bentham, M.; Kirby, G. [British Geological Survey (BGS), Kingsley Dunham Centre, Keyworth, Nottingham (United Kingdom)

2005-06-01

Saline aquifers represent a promising way for CO{sub 2} sequestration. Storage capacities of saline aquifers are very important around the world. The Sleipner site in the North Sea is currently the single case world-wide of CO{sub 2} storage in a saline aquifer. A general review is given on the specific risks for CO{sub 2} storage in saline aquifer. The regional distribution of CO{sub 2} storage potential is presented. Finally, the knowledge gaps and the future research in this field are defined. (authors)

CO2-Water-Rock Wettability: Variability, Influencing Factors, and Implications for CO2 Geostorage.

Science.gov (United States)

Iglauer, Stefan

2017-05-16

Carbon geosequestration (CGS) has been identified as a key technology to reduce anthropogenic greenhouse gas emissions and thus significantly mitigate climate change. In CGS, CO 2 is captured from large point-source emitters (e.g., coal fired power stations), purified, and injected deep underground into geological formations for disposal. However, the CO 2 has a lower density than the resident formation brine and thus migrates upward due to buoyancy forces. To prevent the CO 2 from leaking back to the surface, four trapping mechanisms are used: (1) structural trapping (where a tight caprock acts as a seal barrier through which the CO 2 cannot percolate), (2) residual trapping (where the CO 2 plume is split into many micrometer-sized bubbles, which are immobilized by capillary forces in the pore network of the rock), (3) dissolution trapping (where CO 2 dissolves in the formation brine and sinks deep into the reservoir due to a slight increase in brine density), and (4) mineral trapping (where the CO 2 introduced into the subsurface chemically reacts with the formation brine or reservoir rock or both to form solid precipitates). The efficiency of these trapping mechanisms and the movement of CO 2 through the rock are strongly influenced by the CO 2 -brine-rock wettability (mainly due to the small capillary-like pores in the rock which form a complex network), and it is thus of key importance to rigorously understand CO 2 -wettability. In this context, a substantial number of experiments have been conducted from which several conclusions can be drawn: of prime importance is the rock surface chemistry, and hydrophilic surfaces are water-wet while hydrophobic surfaces are CO 2 -wet. Note that CO 2 -wet surfaces dramatically reduce CO 2 storage capacities. Furthermore, increasing pressure, salinity, or dissolved ion valency increases CO 2 -wettability, while the effect of temperature is not well understood. Indeed theoretical understanding of CO 2 -wettability and the

Estimation of geological storage capacity of CO{sub 2}: Methodology and implementation to the Duero basin (Central East Area); Estimacion de la Capacidad de Almacenamiento Geologico de CO{sub 2}: Metodologia y Aplicacion a la Cuenca del Duero (Zona Centro-Oriental)

Energy Technology Data Exchange (ETDEWEB)

Hurtado, A.; Eguilior, S.

2008-08-06

This paper presents the methodology for assessment of the storage capacity into a saline aquifer depth and the results of the studies carried out in the central east area of the Duero Basin. The extension of the study area represents about 40% of the basin. This methodology has been conducted under the need of estimate of uncertainty in everything related to behavior of long-term stored CO{sub 2} in geological formations because one of the major challenges associated with this activity is ensuring the retention of stored CO{sub 2} along the period of the required time. The method is based on the implementation of a Geographic Information System as a tool for capture, storage, management and presentation of data in maps, as well as a tool for analysis and modelling through its link to both geostatistical methods and description of CO{sub 2} thermodynamic behaviour in deep geological storage conditions, by using real gases Equations of States, specially the Sterner-Pitzer Cubic Equation of State. All these analyses are accompanied by the error propagation due to the calculations required for the determination of the volume of rock, the vertical accuracy of the topographic layers, as well as other uncertainties associated with the variables required for the characterization of the CO{sub 2} in the storage conditions. The conclusion is that the deep geologic CO{sub 2} storage capacity in the study area is between 1,667 and 11,976 Mt, i.e. between 11 and 81 years of storage capacity with a current spanish CO{sub 2} production of 148 Mt/year. (Author) 40 refs.

High-performance cobalt carbonate hydroxide nano-dot/NiCo(CO3)(OH)2 electrode for asymmetric supercapacitors

Science.gov (United States)

Lee, Damin; Xia, Qi Xun; Yun, Je Moon; Kim, Kwang Ho

2018-03-01

Binder-free mesoporous NiCo(CO3)(OH)2 nanowire arrays were grown using a facile hydrothermal technique. The Co2(CO3)(OH)2 in NiCo(CO3)(OH)2 nanowire arrays was well-decorated as nano-dot scale (a few nanometer). In addition, increasing cobalt content in nickel compound matrix, NiCo(CO3)(OH)2 nanowire arrays were separately uniformly grown without agglomeration on Ni foam, providing a high specific surface area to help electrolyte access and ion transfer. The enticing composition and morphology of the NiCo(CO3)(OH)2 nanowire exhibit a superior specific capacity of 1288.2 mAh g-1 at a current density of 3 A g-1 and excellent cycling stability with the capacity retention of 80.7% after 10,000 cycles. Furthermore, an asymmetric supercapacitor composed of the NiCo(CO3)(OH)2 composite as a positive electrode and the graphene as a negative electrode presented a high energy density of 35.5 W h kg-1 at a power density of 2555.6 W kg-1 and satisfactory cycling stability with 71.3% capacity retention after 10,000 cycles. The great combination of the active nano-dot Co2(CO3)(OH)2 and the individually grown NiCo(CO3)(OH)2 nanowires made it a promising electrode material for asymmetric supercapacitors. A well-developed nanoarchitecture of the nano-dot Co2(CO3)(OH)2 decorated NiCo(CO3)(OH)2 composite could pave the way for an excellent electrode design for high-performance supercapacitors.

Polyethyleneimine-loaded bimodal porous silica as low-cost and high-capacity sorbent for CO{sub 2} capture

Energy Technology Data Exchange (ETDEWEB)

Witoon, Thongthai, E-mail: fengttwi@ku.ac.th [National Center of Excellence for Petroleum, Petrochemicals and Advance Material, Department of Chemical Engineering, Faculty of Engineering, Kasetsart University, Bangkok 10900 (Thailand); Center for Advanced Studies in Nanotechnology and Its Applications in Chemical Food and Agricultural Industries, Kasetsart University, Bangkok 10900 (Thailand)

2012-11-15

In this work, bimodal (meso-macro) porous silicas with different mesopore diameters synthesized by using rice husk ash as a low-cost silica source and chitosan as a natural template were used as a polyethyleneimine (PEI) support for CO{sub 2} capture. Unimodal porous silica supports with equivalent mesopore diameters to bimodal porous silica supports have been prepared for purpose of comparison. Effects of different PEI contents (10, 20, 30, 40 and 50 wt%) on CO{sub 2} sorption capacity have been systematically investigated. The porous silica supports and the PEI-loaded porous silica supports were characterized by N{sub 2}-sorption analysis, scanning electron microscopy, Fourier transform infrared spectroscopy and thermal gravimetric analysis. CO{sub 2} sorption measurements of all PEI-loaded porous silica supports were performed at different adsorption temperatures (60, 75, 85, 90, 95 and 105 Degree-Sign C). At low PEI contents (10-20 wt%), the CO{sub 2} sorption of all adsorbents was found to decrease as a function of adsorption temperature, which was a characteristic of a thermodynamically-controlled regime. A transition from the thermodynamically-controlled regime to a kinetically-controlled regime was found when the PEI content was increased up to 30 wt% for PEI-loaded unimodal porous silicas and 40 wt% for PEI-loaded bimodal porous silicas. At high PEI contents (40-50 wt%), the CO{sub 2} capturing efficiency of the PEI-loaded bimodal porous silicas was found to be considerably greater than that of the PEI-loaded unimodal porous silicas, indicating that most of the amine groups of PEI molecules loaded on the unimodal porous silica supports was useless, and thus the appeared macroporosity of the bimodal porous silica supports could provide a higher effective amine density to adsorb CO{sub 2}. Highlights: Black-Right-Pointing-Pointer PEI-impregnated bimodal porous silica as low-cost sorbent for CO{sub 2} capture. Black-Right-Pointing-Pointer Macropores enhances

Ocean CO{sub 2} disposal

Energy Technology Data Exchange (ETDEWEB)

Shindo, Yuji; Hakuta, Toshikatsu [National Inst. of Materials and Chemical Research, AIST, MITI, Higashi, Tsukuba, Ibaraki (Japan)

1993-12-31

Most countries in the world will continue to depend on fossil fuels for their main energy at least for half a country, even in the confrontation with the threat of global warming. This indicates that the development of CO{sub 2} removal technologies such as recovering CO{sub 2} from flue gases and sequestering it of in the deep oceans or subterranean sites is necessary, at least until non-fossil fuel dependent society is developed. Ocean CO{sub 2} disposal is one of the promising options for the sequestration of CO{sub 2} recovered from flue gases. Oceans have sufficient capacity to absorb all the CO{sub 2} emitted in the world. It is very significant to research and develop the technologies for ocean CO{sub 2} disposal.

Coral reefs - sources or sinks of atmospheric CO[sub 2

Energy Technology Data Exchange (ETDEWEB)

Ware, J R; Smith, S V; Reakakudla, M L [Hawaii University, Honolulu, HI (USA). Dept. of Oceanography

1992-09-01

Because the precipitation of calcium carbonate results in the sequestering of carbon, it frequently has been thought that coral reefs function as sinks of global atmospheric CO[sub 2]. However, the precipitation of calcium carbonate is accompanied by a shift of pH that results in the release of CO[sub 2]. This release of CO[sub 2] is less in buffered sea water than fresh water systems; nevertheless, coral reefs are sources, not sinks, of atmospheric carbon. Using estimated rates of coral reef carbonate production, we compute that coral reefs release 0.02 to 0.08 Gt C as CO[sub 2] annually. This is approximately 0.4% to 1.4% of the current anthropogenic CO[sub 2] production due to fossil fuel combustion.

In Vivo Predictive Dissolution: Comparing the Effect of Bicarbonate and Phosphate Buffer on the Dissolution of Weak Acids and Weak Bases.

Science.gov (United States)

Krieg, Brian J; Taghavi, Seyed Mohammad; Amidon, Gordon L; Amidon, Gregory E

2015-09-01

Bicarbonate is the main buffer in the small intestine and it is well known that buffer properties such as pKa can affect the dissolution rate of ionizable drugs. However, bicarbonate buffer is complicated to work with experimentally. Finding a suitable substitute for bicarbonate buffer may provide a way to perform more physiologically relevant dissolution tests. The dissolution of weak acid and weak base drugs was conducted in bicarbonate and phosphate buffer using rotating disk dissolution methodology. Experimental results were compared with the predicted results using the film model approach of (Mooney K, Mintun M, Himmelstein K, Stella V. 1981. J Pharm Sci 70(1):22-32) based on equilibrium assumptions as well as a model accounting for the slow hydration reaction, CO2 + H2 O → H2 CO3 . Assuming carbonic acid is irreversible in the dehydration direction: CO2 + H2 O ← H2 CO3 , the transport analysis can accurately predict rotating disk dissolution of weak acid and weak base drugs in bicarbonate buffer. The predictions show that matching the dissolution of weak acid and weak base drugs in phosphate and bicarbonate buffer is possible. The phosphate buffer concentration necessary to match physiologically relevant bicarbonate buffer [e.g., 10.5 mM (HCO3 (-) ), pH = 6.5] is typically in the range of 1-25 mM and is very dependent upon drug solubility and pKa . © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

Salivary flow rate, buffer capacity, and urea concentration in adolescents with type 1 diabetes mellitus.

Science.gov (United States)

Saes Busato, Ivana Maria; Antoni, Carlos Cesar De; Calcagnotto, Thiago; Ignácio, Sérgio Aparecido; Azevedo-Alanis, Luciana Reis

2016-12-01

The objective of the study was to analyze salivary flow rate, urea concentration, and buffer capacity in adolescents with type 1 diabetes mellitus (type 1 DM) in two different stages. This study was performed on adolescents (14-19 years), allocated between two groups: type 1 DM group comprised 32 adolescents with type 1 DM, and non-type 1 DM group comprised 32 nondiabetics. The adolescents in type 1 DM group were evaluated at a baseline (T0) and after 15 months (T1), and those in non-type 1 DM group were only evaluated at T0. Diabetic status was determined by glycosylated hemoglobin (GHb) and capillary glucose tests. Measurement of salivary flow was performed by means of stimulated saliva (SSFR) collection. The buffer capacity (BC) was determined, and analysis of urea salivary concentration was performed using the colorimetric method. At T0, there were significant differences between diabetics and nondiabetics for SSFR and BC (pdiabetics, SSFR was 0.790 mL/min in T0 and 0.881 mL/min in T1 (p>0.05). BC at T0 was 4.8, and at T1, it was 3.9 (p=0.000). Urea concentration mean value had a significant decrease at T1 (28.13) compared with T0 (34.88) (p=0.013). There was a negative correlation between SSFR and urea salivary concentration at both T0 (r=-0.426, p≤0.05) and T1 (r=-0.601, p≤0.01). In adolescents with type 1 DM, hyposalivation at T0 was associated with an increase in urea salivary concentration. At T1, hyposalivation was associated with a reduction in BC, and an increase in salivary urea.

CO 2 Capture Capacity and Swelling Measurements of Liquid-like Nanoparticle Organic Hybrid Materials via Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy

KAUST Repository

Park, Youngjune; Shin, Dolly; Jang, Young Nam; Park, Ah-Hyung Alissa

2012-01-01

attenuated total reflectance (ATR) Fourier transform infrared (FT-IR) spectroscopy. Simultaneous measurements of CO 2 capture capacity and swelling behaviors of polyetheramine (Jeffamine M-2070) and its corresponding NOHMs (NOHM-I-PE2070) were reported

Supported modified hydrotalcites as sorbent for CO2 capture

Energy Technology Data Exchange (ETDEWEB)

Meis, N.

2010-02-15

The average concentration of CO2 in the atmosphere has been increasing since the start of the industrial revolution in the 18th century from 280 ppm to 385 ppm nowadays, and continues to increase because of the enormous human usage of fossil fuels (oil, gas, coal). This can strongly affect the climate, causing the Earth's surface to warm up, the so called 'amplified greenhouse effect'. To alleviate these environmental concerns regarding the current CO2 emissions into the atmosphere, Carbon Capture and Storage (CCS) is investigated as one of the possible routes. Due to the acidic character of CO2, basic oxides are expected to be suitable sorbents. Hydrotalcite, a natural clay, is specifically suitable for pre-combustion capture (250- 400{sup o}C), due to its acceptable sorption capacity and facile regeneration. The influence of lateral platelet size ({+-}40 nm - 2 {mu}m), the use of a support (carbon nanofibers, CNF) and addition of a promoter (alkali carbonate: K{sub 2}CO{sub 3}/Na{sub 2}CO{sub 3}) on the CO2 capture properties of HT was investigated. There was no significant difference in the CO2 sorption capacities at 523K for all unsupported HTs, regardless the platelet size of the HT precursor ({+-}0.1 mmol.g{sup -1}). The use of activated, promoted (alkali carbonate) hydrotalcites showed a much higher capacity ({+-}0.3 mmol.g{sup -1}) at 523K. In addition, the capacities of the activated supported HT at 523K were significantly increased compared to the activated unsupported HT (1.3-2.5 mmol.g{sup -1} HT). The alkali-loaded supported HTs showed capacities slightly higher than the capacity of supported unpromoted HT. The increase in capacity for the promoted and/or supported HTs points to a higher concentration of defects (low-coordination of oxygen sites) on the surface of the activated (alkali-)loaded HTs compared to the unloaded and unsupported HT. The higher concentration of adsorption for the promoted (supported) HTs, might be caused by the

CO2 clearance by membrane lungs.

Science.gov (United States)

Sun, Liqun; Kaesler, Andreas; Fernando, Piyumindri; Thompson, Alex J; Toomasian, John M; Bartlett, Robert H

2018-05-01

Commercial membrane lungs are designed to transfer a specific amount of oxygen per unit of venous blood flow. Membrane lungs are much more efficient at removing CO 2 than adding oxygen, but the range of CO 2 transfer is rarely reported. Commercial membrane lungs were studied with the goal of evaluating CO 2 removal capacity. CO 2 removal was measured in 4 commercial membrane lungs under standardized conditions. CO 2 clearance can be greater than 4 times that of oxygen at a given blood flow when the gas to blood flow ratio is elevated to 4:1 or 8:1. The CO 2 clearance was less dependent on surface area and configuration than oxygen transfer. Any ECMO system can be used for selective CO 2 removal.

CO2 uptake capacity of coal fly ash

DEFF Research Database (Denmark)

Mazzella, Alessandro; Errico, Massimiliano; Spiga, Daniela

2016-01-01

Coal ashes are normally considered as a waste obtained by the coal combustion in thermal power plants. Their utilization inside the site where are produced represents an important example of sustainable process integration. The present study was performed to evaluate the application of a gas......-solid carbonation treatment on coal fly ash in order to assess the potential of the process in terms of sequestration of CO2 as well as its influence on the leaching behavior of metals and soluble salts. Laboratory tests, performed under different pressure and temperature conditions, showed that in the pressure......% corresponding to a maximum carbonation efficiency of 74%, estimated on the basis of the initial CaO content. The high degree of ash carbonation achieved in the present research, which was conducted under mild conditions, without add of water and without stirring, showed the potential use of coal fly ash in CO2...

Midday depression of CO/sub 2/ assimilation in leaves of Arbutus unedo L. : diurnal changes in photosynthetic capacity related to changes in temperature and humidity

Energy Technology Data Exchange (ETDEWEB)

Raschke, K.; Resemann, A.

1986-01-01

Parts of the attached leaves of the sclerophyllous shrub Arbutus unedo were subjected to simulated mediterranean days. Gas exchange was recorded in order to recognize the causes of the midday depression in CO/sub 2/ assimilation. Depressions could be induced in part of a leaf: they were local responses. The CO/sub 2/-saturation curves of photosynthesis, determined during the morning and afternoon maxima of CO/sub 2/ assimilation and during the minimum at midday, established that depressions in CO/sub 2/ assimilation were in one-half of the investigated cases totally caused by reversible reductions in the photosynthetic capacity of the leaves, and in other half almost totally caused by such reductions. There was no correlation between the water loss with the degree of reduction of the photosynthetic capacity. However, depressions occurred if an apparent threshold in the water-vapor pressure difference between leaf and air was exceeded. In another set of experiments, leaves were subjected to variations in temperature and humidity independent of the time of the day, under otherwise constant conditions. Photosynthetic capacity and stomatal conductance proved to be almost insensitive to changes in temperature (in a range extending from 20 to 37/sup 0/C) as long as the water vapor-pressure difference was held constant. If it was not, the rate of photosynthesis began to decline with increasing temperature after a threshold water-vapor pressure difference was exceeded. The position of the resulting apparent temperature optimum of photosynthesis depended on the humidity of the air. The authors suggest that the ability of A. unedo to respond to a dry atmosphere with a reversible reduction of its photosynthetic capacity (by a still unknown mechanism) is the result of a co-evolution with the development of a strong stomatal sensitivity to changes in humidity. 26 references, 14 figures.

Hybrid of Co(3)Sn(2)@Co nanoparticles and nitrogen-doped graphene as a lithium ion battery anode.

Science.gov (United States)

Mahmood, Nasir; Zhang, Chenzhen; Liu, Fei; Zhu, Jinghan; Hou, Yanglong

2013-11-26

A facile strategy was designed for the fabrication of hybrid of Co3Sn2@Co nanoparticles (NPs) and nitrogen-doped graphene (NG) sheets through a hydrothermal synthesis, followed by annealing process. Core-shell architecture of Co3Sn2@Co pin on NG is designed for the dual encapsulation of Co3Sn2 with adaptable ensembles of Co and NG to address the structural and interfacial stability concerns facing tin-based anodes. In the resulted unique architecture of Co3Sn2@Co-NG hybrid, the sealed cobalt cover prevents the direct exposer of Sn with electrolyte because of encapsulated structure and keeps the structural and interfacial integrity of Co3Sn2. However, the elastically strong, flexible and conductive NG overcoat accommodates the volume changes and therefore brings the structural and electrical stabilization of Co3Sn2@Co NPs. As a result, Co3Sn2@Co-NG hybrid exhibits extraordinary reversible capacity of 1615 mAh/g at 250 mA/g after 100 cycles with excellent capacity retention of 102%. The hybrid bears superior rate capability with reversible capacity of 793.9 mAh/g at 2500 mA/g and Coulombic efficiency nearly 100%.

Microstructure of Co/X (X=Cu,Ag,Au) epitaxial thin films grown on Al2O3(0001) substrates

International Nuclear Information System (INIS)

Ohtake, Mitsuru; Akita, Yuta; Futamoto, Masaaki; Kirino, Fumiyoshi

2007-01-01

Epitaxial thin films of Co/X (X=Cu,Ag,Au) were prepared on Al 2 O 3 (0001) substrates at substrate temperatures of 100 and 300 degree sign C by UHV molecular beam epitaxy. A complicated microstructure was realized for the epitaxial thin films. In-situ reflection high-energy electron diffraction observation has shown that X atoms of the buffer layer segregated to the surface during Co layer deposition, and it yielded a unique epitaxial granular structure. The structure consists of small Co grains buried in the X buffer layer, where both the magnetic small Co grains and the nonmagnetic X layer are epitaxially grown on the single crystal substrate. The structure varied depending on the X element and the substrate temperature. The crystal structure of Co grains is influenced by the buffer layer material and determined to be hcp and fcc structures for the buffer layer materials of Au and Cu, respectively

CO2 Capture by Carbon Aerogel–Potassium Carbonate Nanocomposites

Directory of Open Access Journals (Sweden)

Guang Yang

2016-01-01

Full Text Available Recently, various composites for reducing CO2 emissions have been extensively studied. Because of their high sorption capacity and low cost, alkali metal carbonates are recognized as a potential candidate to capture CO2 from flue gas under moist conditions. However, undesirable effects and characteristics such as high regeneration temperatures or the formation of byproducts lead to high energy costs associated with the desorption process and impede the application of these materials. In this study, we focused on the regeneration temperature of carbon aerogel–potassium carbonate (CA–KC nanocomposites, where KC nanocrystals were formed in the mesopores of the CAs. We observed that the nanopore size of the original CA plays an important role in decreasing the regeneration temperature and in enhancing the CO2 capture capacity. In particular, 7CA–KC, which was prepared from a CA with 7 nm pores, exhibited excellent performance, reducing the desorption temperature to 380 K and exhibiting a high CO2 capture capacity of 13.0 mmol/g-K2CO3, which is higher than the theoretical value for K2CO3 under moist conditions.

Supercritical CO2 uptake by nonswelling phyllosilicates.

Science.gov (United States)

Wan, Jiamin; Tokunaga, Tetsu K; Ashby, Paul D; Kim, Yongman; Voltolini, Marco; Gilbert, Benjamin; DePaolo, Donald J

2018-01-30

Interactions between supercritical (sc) CO 2 and minerals are important when CO 2 is injected into geologic formations for storage and as working fluids for enhanced oil recovery, hydraulic fracturing, and geothermal energy extraction. It has previously been shown that at the elevated pressures and temperatures of the deep subsurface, scCO 2 alters smectites (typical swelling phyllosilicates). However, less is known about the effects of scCO 2 on nonswelling phyllosilicates (illite and muscovite), despite the fact that the latter are the dominant clay minerals in deep subsurface shales and mudstones. Our studies conducted by using single crystals, combining reaction (incubation with scCO 2 ), visualization [atomic force microscopy (AFM)], and quantifications (AFM, X-ray photoelectron spectroscopy, X-ray diffraction, and off-gassing measurements) revealed unexpectedly high CO 2 uptake that far exceeded its macroscopic surface area. Results from different methods collectively suggest that CO 2 partially entered the muscovite interlayers, although the pathways remain to be determined. We hypothesize that preferential dissolution at weaker surface defects and frayed edges allows CO 2 to enter the interlayers under elevated pressure and temperature, rather than by diffusing solely from edges deeply into interlayers. This unexpected uptake of CO 2 , can increase CO 2 storage capacity by up to ∼30% relative to the capacity associated with residual trapping in a 0.2-porosity sandstone reservoir containing up to 18 mass % of illite/muscovite. This excess CO 2 uptake constitutes a previously unrecognized potential trapping mechanism. Copyright © 2018 the Author(s). Published by PNAS.

Characterization of CO2 leakage into the freshwater body

DEFF Research Database (Denmark)

Singh, Ashok; Delfs, Jens Olaf; Shao, H.

2013-01-01

urrent research into CO2 capture and storage is dominated by improving the CO2 storage capacity. In this context, risk related to CO2 leakage is an important issue which may cause environmental problems, particularly when freshwater resources nearby are intruded by the CO2 plume. In this work...

Comparison of Salivary pH, Buffering Capacity and Alkaline Phosphatase in Smokers and Healthy Non-Smokers: Retrospective cohort study

OpenAIRE

Ahmadi-Motamayel, Fatemeh; Falsafi, Parisa; Goodarzi, Mohammad T.; Poorolajal, Jalal

2016-01-01

Objectives: Saliva contains alkaline phosphatase (ALP)—a key intracellular enzyme related to destructive processes and cellular damage—and has buffering capacity (BC) against acids due to the presence of bicarbonate and phosphate ions. Smoking may have deleterious effects on the oral environment due to pH changes which can affect ALP activity. This study aimed to evaluate the salivary pH, BC and ALP activity of male smokers and healthy non-smokers. Methods: This retrospective cohort study ...

Biochars as Potential Adsorbers of CH4, CO2 and H2S

Directory of Open Access Journals (Sweden)

Sumathi Sethupathi

2017-01-01

Full Text Available Methane gas, as one of the major biogases, is a potential source of renewable energy for power production. Biochar can be readily used to purify biogas contaminants such as H2S and CO2. This study assessed the adsorption of CH4, H2S, and CO2 onto four different types of biochars. The adsorption dynamics of biochars were investigated in a fixed-bed column, by determining the breakthrough curves and adsorption capacities of biochars. The physicochemical properties of biochars were considered to justify the adsorption performance. The results showed that CH4 was not adsorbed well by the subjected biochars whereas CO2 and H2S were successfully captured. The H2S and CO2 breakthrough capacity were related to both the surface adsorption and chemical reaction. The adsorption capacity was in the following order: perilla > soybean stover > Korean oak > Japanese oak biochars. The simultaneous adsorption also leads to a competition of sorption sites. Biochars are a promising material for the biogas purification industry.

Enhancement of CO Evolution by Modification of Ga2O3 with Rare-Earth Elements for the Photocatalytic Conversion of CO2 by H2O.

Science.gov (United States)

Tatsumi, Hiroyuki; Teramura, Kentaro; Huang, Zeai; Wang, Zheng; Asakura, Hiroyuki; Hosokawa, Saburo; Tanaka, Tsunehiro

2017-12-12

Modification of the surface of Ga 2 O 3 with rare-earth elements enhanced the evolution of CO as a reduction product in the photocatalytic conversion of CO 2 using H 2 O as an electron donor under UV irradiation in aqueous NaHCO 3 as a pH buffer, with the rare-earth species functioning as a CO 2 capture and storage material. Isotope experiments using 13 CO 2 as a substrate clearly revealed that CO was generated from the introduced gaseous CO 2 . In the presence of the NaHCO 3 additive, the rare-earth (RE) species on the Ga 2 O 3 surface are transformed into carbonate hydrates (RE 2 (CO 3 ) 3 ·nH 2 O) and/or hydroxycarbonates (RE 2 (OH) 2(3-x) (CO 3 ) x ) which are decomposed upon photoirradiation. Consequently, Ag-loaded Yb-modified Ga 2 O 3 exhibits much higher activity (209 μmol h -1 of CO) than the pristine Ag-loaded Ga 2 O 3 . The further modification of the surface of the Yb-modified Ga 2 O 3 with Zn afforded a selectivity toward CO evolution of 80%. Thus, we successfully achieved an efficient Ag-loaded Yb- and Zn-modified Ga 2 O 3 photocatalyst with high activity and controllable selectivity, suitable for use in artificial photosynthesis.

Sonochemical surface functionalization of exfoliated LDH: Effect on textural properties, CO2 adsorption, cyclic regeneration capacities and subsequent gas uptake for simultaneous methanol synthesis.

Science.gov (United States)

Ezeh, Collins I; Huang, Xiani; Yang, Xiaogang; Sun, Cheng-Gong; Wang, Jiawei

2017-11-01

To improve CO 2 adsorption, amine modified Layered double hydroxide (LDH) were prepared via a two stage process, SDS/APTS intercalation was supported by ultrasonic irradiation and then followed by MEA extraction. The prepared samples were characterised using Scanning electron microscope-Energy dispersive X-ray spectroscopy (SEM-EDX), X-ray Photoelectron Spectroscopy (XPS), X-ray diffraction (XRD), Temperature Programmed Desorption (TPD), Brunauer-Emmett-Teller (BET), and Thermogravimetric analysis (TGA), respectively. The characterisation results were compared with those obtained using the conventional preparation method with consideration to the effect of sonochemical functionalization on textural properties, adsorption capacity, regeneration and lifetime of the LDH adsorbent. It is found that LDHs prepared by sonochemical modification had improved pore structure and CO 2 adsorption capacity, depending on sonic intensity. This is attributed to the enhanced deprotonation of activated amino functional groups via the sonochemical process. Subsequently, this improved the amine loading and effective amine efficiency by 60% of the conventional. In addition, the sonochemical process improved the thermal stability of the adsorbent and also, reduced the irreversible CO 2 uptake, CUirrev, from 0.18mmol/g to 0.03mmol/g. Subsequently, improving the lifetime and ease of regenerating the adsorbent respectively. This is authenticated by subjecting the prepared adsorbents to series of thermal swing adsorption (TSA) cycles until its adsorption capacity goes below 60% of the original CO 2 uptake. While the conventional adsorbent underwent a 10 TSA cycles before breaking down, the sonochemically functionalized LDH went further than 30 TSA cycles. Copyright © 2017 Elsevier B.V. All rights reserved.

One-Step Fast-Synthesized Foamlike Amorphous Co(OH)2 Flexible Film on Ti Foil by Plasma-Assisted Electrolytic Deposition as a Binder-Free Anode of a High-Capacity Lithium-Ion Battery.

Science.gov (United States)

Li, Tao; Nie, Xueyuan

2018-05-23

This research prepared an amorphous Co(OH) 2 flexible film on Ti foil using plasma-assisted electrolytic deposition within 3.5 min. Amorphous Co(OH) 2 structure was determined by X-ray diffraction and X-ray photoelectron spectroscopy. Its areal capacity testing as the binder and adhesive-free anode of a lithium-ion battery shows that the cycling capacity can reach 2000 μAh/cm 2 and remain at 930 μAh/cm 2 after 50 charge-discharge cycles, which benefits from the emerging Co(OH) 2 active material and amorphous foamlike structure. The research introduced a new method to synthesize amorphous Co(OH) 2 as the anode in a fast-manufactured low-cost lithium-ion battery.

Enhanced binding affinity, remarkable selectivity, and high capacity of CO 2 by dual functionalization of a rht-type metal-organic framework

KAUST Repository

Li, Baiyan

2011-12-23

Open and friendly: The smallest member of the rht-type metal-organic frameworks (MOFs, see picture) constructed by a hexacarboxylate ligand with a nitrogen-rich imino triazine backbone shows a significantly enhanced gas binding affinity relative to all other isoreticular rht-type MOFs. The high adsorption capacity and remarkable selectivity of CO 2 are attributed to the high density of open metal and Lewis basic sites in the framework. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Concurrent separation of CO2 and H2O from air by a temperature-vacuum swing adsorption/desorption cycle.

Science.gov (United States)

Wurzbacher, Jan Andre; Gebald, Christoph; Piatkowski, Nicolas; Steinfeld, Aldo

2012-08-21

A temperature-vacuum swing (TVS) cyclic process is applied to an amine-functionalized nanofibrilated cellulose sorbent to concurrently extract CO(2) and water vapor from ambient air. The promoting effect of the relative humidity on the CO(2) capture capacity and on the amount of coadsorbed water is quantified. The measured specific CO(2) capacities range from 0.32 to 0.65 mmol/g, and the corresponding specific H(2)O capacities range from 0.87 to 4.76 mmol/g for adsorption temperatures varying between 10 and 30 °C and relative humidities varying between 20 and 80%. Desorption of CO(2) is achieved at 95 °C and 50 mbar(abs) without dilution by a purge gas, yielding a purity exceeding 94.4%. Sorbent stability and a closed mass balance for both H(2)O and CO(2) are demonstrated for ten consecutive adsorption-desorption cycles. The specific energy requirements of the TVS process based on the measured H(2)O and CO(2) capacities are estimated to be 12.5 kJ/mol(CO2) of mechanical (pumping) work and between 493 and 640 kJ/mol(CO2) of heat at below 100 °C, depending on the air relative humidity. For a targeted CO(2) capacity of 2 mmol/g, the heat requirement would be reduced to between 272 and 530 kJ/mol(CO2), depending strongly on the amount of coadsorbed water.

One-pot fabrication of graphene sheets decorated Co2P-Co hollow nanospheres for advanced lithium ion battery anodes

International Nuclear Information System (INIS)

Xie, Qingshui; Zeng, Deqian; Gong, Pingyun; Huang, Jian; Ma, Yating; Wang, Laisen; Peng, Dong-Liang

2017-01-01

Highlights: • Co 2 P-Co hollow nanospheres with graphene sheets decoration are prepared through one-pot solution approach. • Co 2 P-Co/graphene nanocomposites reveal greatly enhanced lithium storage performances than Co 2 P-Co counterparts. • The superb electrochemical performances derive from dual modification of graphene sheets and metal Co as well as their hollow configuration. - Abstract: The fabrication of Co 2 P-Co (Co-P composites) hollow nanospheres with graphene sheets decoration through one-pot solution approach is demonstrated and their potential as the anode materials for lithium ion batteries is assessed. A large specific capacity of 929 mA h g −1 can be retained for Co-P/graphene nanocomposites at 100 mA g −1 after 200 cycles. When cycled at a large current density of 2.0C, the Co-P/graphene nanocomposites deliver a decent reversible capacity of 567 mA h g −1 , which is much higher than the theoretical capacity of traditional graphite anode (372 mA h g −1 ). The obviously enhanced lithium storage properties of Co-P/graphene nanocomposites are put down to the dual modification of graphene sheets and metal Co as well as their hollow structures.

Effect of heat treatment on CO2 adsorption of KOH-activated graphite nanofibers.

Science.gov (United States)

Meng, Long-Yue; Park, Soo-Jin

2010-12-15

In this work, graphite nanofibers (GNFs) were successfully expanded intercalating KOH followed by heat treatment in the temperature range of 700-1000 °C. The aim was to improve the CO(2) adsorption capacity of the GNFs by increasing the porosity of GNFs. The effects of heat treatment on the pore structures of GNFs were investigated by N(2) full isotherms, XRD, SEM, and TEM. The CO(2) adsorption capacity was measured by CO(2) isothermal adsorption at 25 °C and 1 atm. From the results, it was found that the activation temperature had a major influence on CO(2) adsorption capacity and textural properties of GNFs. The specific surface area, total pore volume, and mesopore volume of the GNFs increased after heat treatment. The CO(2) adsorption isotherms showed that G-900 exhibited the best CO(2) adsorption capacity with 59.2 mg/g. Copyright © 2010 Elsevier Inc. All rights reserved.

pKa value and buffering capacity of acidic monomers commonly used in self-etching primers.

Science.gov (United States)

Salz, Ulrich; Mücke, Angela; Zimmermann, Jörg; Tay, Franklin R; Pashley, David H

2006-06-01

The aim of this investigation was to characterize acidic monomers used in self-etching primers/adhesives by determination of their pKa values and by calculation of their calcium dissolving capacity in comparison with phosphoric and hydrochloric acid. The following acidic monomers were included in this study: 4-methacryloyloxyethyl trimellitate anhydride (4-META), 10-methacryloyloxydecyl dihydrogen phosphate (MDP), dimethacryloyloxyethyl hydrogen phosphate (di-HEMA-phosphate), ethyl 2-[4-(dihydroxyphosphoryl)-2-oxabutyl]acrylate (EAEPA), 2-[4-(dihydroxyphosphoryl)-2-ox-abutyl]acrylic acid (HAEPA), and 2,4,6 trimethylphenyl 2-[4-(dihydroxyphosphoryl)-2-oxabutyl]acrylate (MAEPA). The pKa values were obtained by titration with 0.1 mol/l NaOH in aqueous solution. The inflection points of the resulting potentiometric titration curve were determined as pKa values. In the case of the sparingly water-soluble acidic monomers MAEPA and 4-META, the co-solvent method using different water/ethanol ratios for MAEPA or water/acetone ratios for 4-META was used. The dissolving capacity of each acidic monomer is defined as the amount of hydroxyapatite (HA) dissolved by 1 g of acid. For each monomer, the HA dissolving capacity was calculated bythe corresponding pKa value and the molecular weight. To confirm the calculated dissolving capacities, increasing amounts of HA powder (100 mg portions) were slowly added to 15 mmol/l aqueous solutions of the monomers to determine how much HA could be dissolved in the acidic solutions. For all the investigated acidic monomers, pKal values between 1.7 to 2.5 were observed. The pKa2 values for the phosphate/phosphonate derivatives are between 7.0 and 7.3, and are comparable to phosphoric acid. For dicarboxylic acid derivatives, the pKa2 values are in the range of 4.2 to 4.5. Due to their comparable molecular weights and pKal values, the three tested acids di-HEMA phosphate, MDP and 4-META all possess comparable dissolving capacities for HA (ie, 0

New transcritical CO{sub 2} compressor series; Neue transkritische CO{sub 2}-Verdichterbaureihe

Energy Technology Data Exchange (ETDEWEB)

Froeschle, Manuel [GEA Bock GmbH, Frickenhausen (Germany)

2011-10-15

The use of natural refrigerants that is recently discussed, is not a new development, but has grown in importance in the last few years. Particularly in the supermarket- and heat pump area, a growing demand in CO{sub 2}-systems for subcritical and transcritical applications could be observed. An extension of the CO{sub 2} components in this area is therefore absolutely necessary. For this reason a completely new transcritical compressor series for maximum pressures of up to 150 bar and extended capacity stages was developed especially. (orig.)

Alteration of bentonite when contacted with supercritical CO2

Science.gov (United States)

Jinseok, K.; Jo, H. Y.; Yun, S. T.

2014-12-01

Deep saline formations overlaid by impermeable caprocks with a high sealing capacity are attractive CO2 storage reservoirs. Shales, which consist of mainly clay minerals, are potential caprocks for the CO2 storage reservoirs. The properties of clay minerals in shales may affect the sealing capacity of shales. In this study, changes in clay minerals' properties when contacted with supercritical (SC) CO2 at various conditions were investigated. Bentonite, whichis composed of primarily montmorillonite, was used as the clay material in this study. Batch reactor tests on wet bentonite samples in the presence of SC CO2 with or without aqueous phases were conducted at high pressure (12 MPa) and moderate temperature (50 oC) conditions for a week. Results show that the bentonite samples obtained from the tests with SC CO2 had less change in porosity than those obtained from the tests without SC CO2 (vacuum-drying) at a given reaction time, indicating that the bentonite samples dried in the presence of SC CO2 maintained their structure. These results suggest that CO2 molecules can diffuse into interlayer of montmorillonite, which is a primary mineral of bentonite, and form a single CO2 molecule layer or double CO2 molecule layers. The CO2 molecules can displace water molecules in the interlayer, resulting in maintaining the interlayer spacing when dehydration occurs. Noticeable changes in reacted bentonite samples obtained from the tests with an aqueous phase (NaCl, CaCl2, or sea water) are decreases in the fraction of plagioclase and pyrite and formation of carbonate minerals (i.e., calcite and dolomite) and halite. In addition, no significant exchanges of Na or Ca on the exchangeable complex of the montmorillonite in the presence of SC CO2 occurred, resulting in no significant changes in the swelling capacity of bentonite samples after reacting with SC CO2 in the presence of aqueous phases. These results might be attributed by the CO2 molecule layer, which prevents

Investigation of the conversion mechanism of nanosized CoF2

International Nuclear Information System (INIS)

Teng, Yin Ting; Pramana, Stevin S.; Ding, Junfeng; Wu, Tom; Yazami, Rachid

2013-01-01

Highlights: • First report on synthesis of nanosized cobalt fluoride via precipitation. • CoF x formation during recharging commences at the interface between cobalt and lithium fluoride. • Valance change of cobalt in cobalt fluoride electrode upon discharging and recharging is shown from EELS and XPS. • Lithiation of CoF 2 leads to formation of superparamagnetic nanosized cobalt particles. • Morphology of the conductive carbon addictives used plays a crucial factor in determining the capacity retention ability. -- Abstract: Nanoparticles (∼20 nm) of tetragonal (P42/mnm) cobalt fluoride (CoF 2 ) has been synthesized by precipitation using cobalt nitrate and ammonium fluoride solution at room temperature, followed by annealing at 400 °C under argon atmosphere. The morphology and structure have been studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and transmission electron microscopy (TEM). The electrochemical lithiation of CoF 2 and its structural and valence changes during conversion have been investigated. Electrochemical measurements revealed a discharge specific capacity close to theoretical specific capacity of 553 mAh g −1 and charge specific capacities ranging from 250 to 450 mAh g −1 in the first cycle, depending on the type of conductive carbon addictive used. Lithiation of CoF 2 occurs without any intercalation, but via conversion reaction CoF 2 + 2Li + + 2e − → Co(0) + 2LiF. During lithiation, CoF 2 is fully reduced to Co(0) and breaks down into smaller particles of ∼2 nm. Upon recharging, CoF x is formed instead of CoF 2 . XPS and EELS studies show that only the surface of the electrode is reconverted back to CoF x during recharging. In addition, recharging to form CoF x commences at the interface between the cobalt and lithium fluoride. These results offer the experimental evidence explaining the lack of cycle stability of metal fluorides that undergo a conversion reaction with lithium such

Pressure buffering by the tympanic membrane. In vivo measurements of middle ear pressure fluctuations during elevator motion.

Science.gov (United States)

Padurariu, Simona; de Greef, Daniël; Jacobsen, Henrik; Nlandu Kamavuako, Ernest; Dirckx, Joris J; Gaihede, Michael

2016-10-01

The tympanic membrane (TM) represents a pressure buffer, which contributes to the overall pressure regulation of the middle ear (ME). This buffer capacity is based on its viscoelastic properties combined with those of the attached ossicular chain, muscles and ligaments. The current work presents a set of in vivo recordings of the ME pressure variations normally occurring in common life: elevator motion. This is defined as a situation of smooth ambient pressure increase or decrease on a limited range and at a low rate of pressure change. Based on these recordings, the purpose was a quantitative analysis of the TM buffer capacity including the TM compliance. The pressure changes in seven normal adult ME's with intact TM's were continuously recorded directly inside the ME cavity during four different elevator trips using a high precision instrument. The TM buffer capacity was determined by the ratio between the changes in ME and the ambient pressure. Further, the ME volumes were calculated by Boyle's Law from pressure recordings during inflation-deflation tests; subsequently the TM compliance could also be calculated. Finally, the correlation between the ME volume and buffer function was determined. Twenty-one elevator trips could be used for the analysis. The overall mean TM pressure buffering capacity was 23.3% (SEM = 3.4), whereas the mean overall compliance was 28.9 × 10 -3  μL/Pa (SEM = 4.8). A strong negative linear correlation was found between the TM buffer capacity and the ME volumes (R 2  = 0.92). These results were in fair agreement with the literature obtained in clinical as well as temporal bone experiments, and they provide an in vivo reference for the normal ME function as well as for ME modeling. The TM buffer capacity was found more efficient in smaller mastoids. Possible clinical implications are discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

Hydrothermal synthesis and electrochemical properties of nano-sized Co-Sn alloy anodes for lithium ion batteries

International Nuclear Information System (INIS)

He Jianchao; Zhao Hailei; Wang Jing; Wang Jie; Chen Jingbo

2010-01-01

Research highlights: → Nano-sized Co-Sn alloys were synthesized by hydrothermal route. → Li 2 O and CoSn can buffer the large volume change associated with lithiation of Sn. → A two-step reaction mechanism of CoSn 2 alloy during cycling was confirmed. - Abstract: Nano-sized Co-Sn alloys with a certain amount of Sn oxides used as potential anode materials for lithium ion batteries were synthesized by hydrothermal route. The effects of hydrothermal conditions and post annealing on the phase compositions and the electrochemical properties of synthesized powders were characterized by means of X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM) with energy dispersive spectra (EDS) analysis and galvanostatic cycling tests. Prolonging the dwelling time at the same hydrothermal temperature can increase the content of Sn oxides, which will lead to a high initial irreversible capacity loss but a better cycling stability owing to the buffer effect of irreversible product Li 2 O. Heat-treatment can increase the crystallinity and cause the presence of a certain amount of inert CoSn component, which both have positive impact on the cycling stability of Co-Sn electrode. By comparison with the lithiation/delithiation processes of metal Sn, a two-step mechanism of CoSn 2 alloy during cycling was confirmed.

Continuous CO2 capture and MSWI fly ash stabilization, utilizing novel dynamic equipment

International Nuclear Information System (INIS)

Jiang Jianguo; Du Xuejuan; Chen Maozhe; Zhang Chang

2009-01-01

Novel dynamic equipment with gas in and out continuously was developed to study the capture capacity of CO 2 . Municipal solid waste incineration (MSWI) fly ash has a high capture rate of CO 2 in CO 2 -rich gas. Fly ash can sequester pure CO 2 rapidly, and its capacity is 16.3 g CO 2 /100 g fly ash with no water added and 21.4 g CO 2 /100 g fly ash with 20% water added. For simulated incineration gas containing 12% CO 2 , the capture rate decreased and the capacity was 13.2 g CO 2 /100 g fly ash with no water added and 18.5 g CO 2 /100 g fly ash with 20% water added. After accelerated carbonation, the C and O contents increased, indicating CO 2 capture in the fly ash; CO 2 combines with Ca(OH) 2 to form CaCO 3 , which increased the CaCO 3 content from 12.5 to 54.3%. The leaching of Pb markedly decreased from 24.48 to 0.111 mg/L. - Novel dynamic equipment designed to capture CO 2 by fly ash is more suitable for engineering application.

Utilizing Co2+/Co3+ Redox Couple in P2-Layered Na0.66Co0.22Mn0.44Ti0.34O2 Cathode for Sodium-Ion Batteries.

Science.gov (United States)

Wang, Qin-Chao; Hu, Enyuan; Pan, Yang; Xiao, Na; Hong, Fan; Fu, Zheng-Wen; Wu, Xiao-Jing; Bak, Seong-Min; Yang, Xiao-Qing; Zhou, Yong-Ning

2017-11-01

Developing sodium-ion batteries for large-scale energy storage applications is facing big challenges of the lack of high-performance cathode materials. Here, a series of new cathode materials Na 0.66 Co x Mn 0.66- x Ti 0.34 O 2 for sodium-ion batteries are designed and synthesized aiming to reduce transition metal-ion ordering, charge ordering, as well as Na + and vacancy ordering. An interesting structure change of Na 0.66 Co x Mn 0.66- x Ti 0.34 O 2 from orthorhombic to hexagonal is revealed when Co content increases from x = 0 to 0.33. In particular, Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 with a P2-type layered structure delivers a reversible capacity of 120 mAh g -1 at 0.1 C. When the current density increases to 10 C, a reversible capacity of 63.2 mAh g -1 can still be obtained, indicating a promising rate capability. The low valence Co 2+ substitution results in the formation of average Mn 3.7+ valence state in Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 , effectively suppressing the Mn 3+ -induced Jahn-Teller distortion, and in turn stabilizing the layered structure. X-ray absorption spectroscopy results suggest that the charge compensation of Na 0.66 Co 0.22 Mn 0.44 Ti 0.34 O 2 during charge/discharge is contributed by Co 2.2+ /Co 3+ and Mn 3.3+ /Mn 4+ redox couples. This is the first time that the highly reversible Co 2+ /Co 3+ redox couple is observed in P2-layered cathodes for sodium-ion batteries. This finding may open new approaches to design advanced intercalation-type cathode materials.

Photo-induced wettability of TiO{sub 2} film with Au buffer layer

Energy Technology Data Exchange (ETDEWEB)

Purkayastha, Debarun Dhar; Sangani, L. D. Varma; Krishna, M. Ghanashyam [School of Physics, University of Hyderabad, Hyderabad-500046 (India); Madhurima, V., E-mail: madhurima.v@gmail.com [Department of Physics, Central University of Tamil Nadu, Thiruvarur-610004 (India)

2014-04-24

The effect of thickness of Au buffer layer (15-25 nm) between TiO{sub 2} film and substrate on the wettability of TiO{sub 2} films is reported. TiO{sub 2} films grown on Au buffer layer have a higher contact angle of 96-;100° as compared to 47.6o for the film grown without buffer layer. The transition from hydrophobicity to hydrophilicity under UV irradiation occurs within 10 min. for the buffer layered films whereas it is almost 30 min. for the film grown without buffer layer. The enhanced photo induced hydrophilicity is shown to be surface energy driven.

Porous carbon from local coconut shell char by CO2 and H2O activation in the presence of K2CO3

Science.gov (United States)

Vi, Nguyen Ngoc Thuy; Truyen, Dang Hai; Trung, Bien Cong; An, Ngo Thanh; Van Dung, Nguyen; Long, Nguyen Quang

2017-09-01

Vietnamese coconut shell char was activated by steam and carbon dioxide at low temperatures with the presence of K2CO3 as a catalyst. The effects of process parameters on adsorption capability of the product including different ratio of impregnation of activation agents, activation temperature, activation time were investigated in this study. Iodine number, methylene blue adsorption capacity, specific surface area and pore size distribution were measured to assess the properties of the activated carbon. Accordingly, the porous carbon was applied for toluene removal by adsorption technology. Significant increases in specific surface area and the toluene adsorption capacity were observed when the coconut shell char was activated in CO2 flow at 720 °C for 150 minutes and the K2CO3/char weight ratio of 0.5.

On the Stability of DNA Origami Nanostructures in Low-Magnesium Buffers.

Science.gov (United States)

Kielar, Charlotte; Xin, Yang; Shen, Boxuan; Kostiainen, Mauri A; Grundmeier, Guido; Linko, Veikko; Keller, Adrian

2018-05-25

DNA origami have great potential as functional platforms in various biomedical applications. Many applications, however, are incompatible with the high Mg2+ concentrations commonly believed to be a prerequisite for maintaining DNA origami integrity. Here, we investigate DNA origami stability in low-Mg2+ buffers. DNA origami stability is found to crucially depend on the availability of residual Mg2+ ions for screening electrostatic repulsion. The presence of EDTA and phosphate ions may thus facilitate DNA origami denaturation by displacing Mg2+ ions from the DNA backbone and reducing the strength of the Mg2+-DNA interaction, respectively. Most remarkably, these buffer dependencies are affected by DNA origami superstructure. However, by rationally selecting buffer components and considering superstructure-dependent effects, the structural integrity of a given DNA origami nanostructure can be maintained in conventional buffers even at Mg2+ concentrations in the low-μM range. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of the buffering capacity of the soil on the mobilization of heavy metals. Equilibrium and kinetics.

Science.gov (United States)

Villen-Guzman, Maria; Paz-Garcia, Juan M; Amaya-Santos, Gema; Rodriguez-Maroto, Jose M; Vereda-Alonso, Carlos; Gomez-Lahoz, Cesar

2015-07-01

Understanding the possible pH-buffering processes is of maximum importance for risk assessment and remediation feasibility studies of heavy-metal contaminated soils. This paper presents the results about the effect of the buffering capacity of a polluted soil, rich in carbonates, on the pH and on the leaching evolution of its main contaminant (lead) when a weak acid (acetic acid) or a strong one (nitric acid) are slowly added. In both cases, the behavior of lead dissolution could be predicted using available (scientifically verified freeware) models assuming equilibrium between the solid and the aqueous phase. However, the experimental results indicate that the dissolution of calcium and magnesium carbonates is kinetically controlled. These kinetic limitations affect the overall behavior, and should be considered to understand also the response of the metals under local equilibrium. The well-known BCR sequential extraction procedure was used before- and after-treatment, to fractionate the lead concentration in the soil according to its mobility. The BCR results were also in agreement with the predictions of the equilibrium model. This agreement allows new insights about the information that could be derived from the BCR fractionation analysis. Copyright © 2015 Elsevier Ltd. All rights reserved.

Development of TREN dendrimers over mesoporous SBA-15 for CO2 adsorption

International Nuclear Information System (INIS)

Bhagiyalakshmi, Margandan; Park, Sang Do; Cha, Wang Seog; Jang, Hyun Tae

2010-01-01

Mesoporous SBA-15 was synthesized using rice husk ash (RHA) as the silica source and their defective Si-OH groups were grafted with tris(2-aminoethyl) amine (TREN) dendrimers generation through step-wise growth technique. The X-ray diffraction (XRD) and nitrogen adsorption/desorption results of parent SBA-15 obtained from RHA, suggests its resemblance with SBA-15 synthesized using conventional silica sources. Furthermore, the nitrogen adsorption/desorption results of SBA-15/TREN dendrimer generations (G1-G3) illustrates the growth of dendrimer inside the mesopores of SBA-15 and their CO 2 adsorption capacity was determined at 25 deg. C. The maximum CO 2 adsorption capacity of 5-6 and 7-8 wt% over second and third dendrimer generation was observed which is discernibly higher than the reported melamine and PAMAM dendrimers. The experimental CO 2 adsorption capacity was found to be less than theoretically calculated CO 2 adsorption capacity due to inter and intra molecular amidation as result of steric hindrance during the dendrimer growth. These SBA-15/TREN dendrimer generations also exhibit thermal stability up to 350 deg. C and CO 2 adsorption capacity remains unaltered upon seven consecutive runs.

Biogeochemical processes in a clay formation in situ experiment: Part B - Results from overcoring and evidence of strong buffering by the rock formation

Energy Technology Data Exchange (ETDEWEB)

Koroleva, M. [Institute of Geological Sciences, University of Bern, Baltzerstrasse 3, CH-3012 Bern (Switzerland); Lerouge, C. [BRGM, French Geological Survey, 3 Avenue Claude Guillemin, B.P. 36009, 45060 Orleans Cedex 2 (France); Maeder, U., E-mail: urs.maeder@geo.unibe.ch [Institute of Geological Sciences, University of Bern, Baltzerstrasse 3, CH-3012 Bern (Switzerland); Claret, F.; Gaucher, E. [BRGM, French Geological Survey, 3 Avenue Claude Guillemin, B.P. 36009, 45060 Orleans Cedex 2 (France)

2011-06-15

Highlights: > A 5-year in situ porewater chemistry experiment in Opalinus Clay was overcored and examined. > A microbial perturbation induced sulfate reduction, pH decrease and alkalinity / P{sub CO2} increase. > Changes to mineralogy, isotopic composition and bulk properties could not be detected. > Precipitation of Fe-sulfides and carbonate occurred at the interface of the test interval. > The chemical perturbation was effectively buffered by the claystone's large capacity. - Abstract: An in situ Porewater Chemistry (PC) experiment in the Opalinus Clay formation was carried out at the Mont Terri underground rock laboratory (Jura Mountains, Switzerland) for a period of 5 a. A traced water with a composition close to that expected in the formation was continuously circulated and monitored in a packed-off borehole to achieve diffusive equilibration. An unwanted microbial perturbation changed the water composition, characterized by reduction of SO{sub 4} combined with increasing sulfide, increasing alkalinity, decreasing pH and increasing P(CO{sub 2}). In contrast, the main cations (Na, Ca, Mg) remained remarkably constant during the experiment, thus indicating the strong buffering of the formation via cation and proton exchange as well as carbonate dissolution/precipitation reactions. After 5 a, the 4.5 m long vertical test interval was overcored and Opalinus Clay samples were analyzed along ca. 15 cm long radial profiles. The analytical investigations included mineralogy (XRD, SEM-EDX), bulk parameters (water content, density, C, S), cation exchange capacity and occupancy, aqueous leachates for Cl{sup -}, Br{sup -}, SO{sub 4}{sup 2-} and water and carbonate stable isotopes. Emphasis was put on best sample preparation and conservation techniques. Results show that the distribution of non-reactive tracers (Br{sup -} and {sup 2}H) follows the expected out/in-diffusion profiles compatible with the time-dependent boundary conditions in the test interval of the

CaO-Based CO2 Sorbents Effectively Stabilized by Metal Oxides.

Science.gov (United States)

Naeem, Muhammad Awais; Armutlulu, Andac; Imtiaz, Qasim; Müller, Christoph R

2017-11-17

Calcium looping (i.e., CO 2 capture by CaO) is a promising second-generation CO 2 capture technology. CaO, derived from naturally occurring limestone, offers an inexpensive solution, but due to the harsh operating conditions of the process, limestone-derived sorbents undergo a rapid capacity decay induced by the sintering of CaCO 3 . Here, we report a Pechini method to synthesize cyclically stable, CaO-based CO 2 sorbents with a high CO 2 uptake capacity. The sorbents synthesized feature compositional homogeneity in combination with a nanostructured and highly porous morphology. The presence of a single (Al 2 O 3 or Y 2 O 3 ) or bimetal oxide (Al 2 O 3 -Y 2 O 3 ) provides cyclic stability, except for MgO which undergoes a significant increase in its particle size with the cycle number. We also demonstrate a direct relationship between the CO 2 uptake and the morphology of the synthesized sorbents. After 30 cycles of calcination and carbonation, the best performing sorbent, containing an equimolar mixture of Al 2 O 3 and Y 2 O 3 , exhibits a CO 2 uptake capacity of 8.7 mmol CO 2  g -1 sorbent, which is approximately 360 % higher than that of the reference limestone. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Buffers for biomass production in temperate European agriculture

DEFF Research Database (Denmark)

Christen, Benjamin; Dalgaard, Tommy

2013-01-01

, environmental pressures from intensive agriculture and policy developments. Use of conservation buffers by farmers outside of designated schemes is limited to date, but the increasing demand for bioenergy and the combination of agricultural production with conservation calls for a much wider implementation....... This paper reviews the biophysical knowledge on buffer functioning and associated ecosystem services. It describes how a three-zone buffer design, with arable fields buffered in combination by grassland, short rotation forestry (SRF) or coppice (SRC) and undisturbed vegetation along water courses, can...... be incorporated into farming landscapes as productive conservation elements and reflects on the potential for successful implementation. Land use plays a much greater role in determining catchment hydrology than soil type: shelterbelts or buffer strips have markedly higher infiltration capacity than arable...

Development of pure Mg open-cell foams as structured CO{sub 2} captor

Energy Technology Data Exchange (ETDEWEB)

Figueroa, I.A., E-mail: iafiguera@unam.mx [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico); Suarez, M.A.; Velasco-Castro, M.; Pfeiffer, H.; Alcántar-Vázquez, B.; González, G. [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico); Alfonso, I. [Instituto de Investigaciones en Materiales, Unidad Morelia, Universidad Nacional Autónoma de México, Campus Morelia UNAM, Antigua Carretera a Pátzcuaro No. 8701, Col. Ex-Hacienda de San José de la Huerta, C.P. 58190 Morelia, Michoacán (Mexico); Lara-Rodríguez, G.A. [Instituto de Investigaciones en Materiales, Universidad Nacional Autónoma de México (UNAM), Circuito Exterior S/N, Cd. Universitaria, C.P. 04510 México, D.F. (Mexico)

2015-12-10

Highlights: • The CO{sub 2} capture capacity of the open-cell Mg foams was studied at low temperatures. • Open-cell Mg foams with pore size of 350 μm were used for the CO{sub 2} capture study. • The highest amount of CO{sub 2} captured was obtained at 60 °C and 80% of relative humidity. • A CO{sub 2} capture capacity of 0.87 mmol/g was obtained for the open-cell Mg foams. • The oxidized open-cell Mg foams can be used as CO{sub 2} captors. - Abstract: The CO{sub 2} capture capacity of the superficial oxide layer formed in pure open-cell Mg foams was studied at low temperatures (40–60 °C) varying the relative humidity from 40 to 80%. Mg foam samples with pore size of 350 μm and surface area of 5.4 m{sup 2}/g were used for these analyses. Optical microscopy and X-ray diffraction techniques were used to characterize the cell structure and the superficial oxide formed in the cell-foams, respectively. The final products formed after the CO{sub 2}–H{sub 2}O capture experiments were identified by scanning electron microscopy and attenuated total reflexion-Fourier transform infrared spectroscopy (ATR-FTIR). The MgCO{sub 3} and other products, formed after CO{sub 2} + H{sub 2}O capture process, were thermally decomposed, to quantify the amount of CO{sub 2} captured by the superficial MgO layer using standard thermogravimetric analysis. The results showed that the highest amount of CO{sub 2} captured was obtained at 60 °C and 80% of relative humidity, with a CO{sub 2} capture capacity of 0.87 mmol/g, which is comparable with others CO{sub 2} MgO-based captors. The considerable CO{sub 2} capture capacity at low temperatures supports the potential of the pure open-cell Mg foams to be used as structured CO{sub 2} captors.

Influence of training intensity on adaptations in acid/base transport proteins, muscle buffer capacity, and repeated-sprint ability in active men.

Science.gov (United States)

McGinley, Cian; Bishop, David J

2016-12-01

McGinley C, Bishop DJ. Influence of training intensity on adaptations in acid/base transport proteins, muscle buffer capacity, and repeated-sprint ability in active men. J Appl Physiol 121: 1290-1305, 2016. First published October 14, 2016; doi:10.1152/japplphysiol.00630.2016-This study measured the adaptive response to exercise training for each of the acid-base transport protein families, including providing isoform-specific evidence for the monocarboxylate transporter (MCT)1/4 chaperone protein basigin and for the electrogenic sodium-bicarbonate cotransporter (NBCe)1. We investigated whether 4 wk of work-matched, high-intensity interval training (HIIT), performed either just above the lactate threshold (HIITΔ20; n = 8), or close to peak aerobic power (HIITΔ90; n = 8), influenced adaptations in acid-base transport protein abundance, nonbicarbonate muscle buffer capacity (βm in vitro ), and exercise capacity in active men. Training intensity did not discriminate between adaptations for most proteins measured, with abundance of MCT1, sodium/hydrogen exchanger (NHE) 1, NBCe1, carbonic anhydrase (CA) II, and CAXIV increasing after 4 wk, whereas there was little change in CAIII and CAIV abundance. βm in vitro also did not change. However, MCT4 protein content only increased for HIITΔ20 [effect size (ES): 1.06, 90% confidence limits × / ÷ 0.77], whereas basigin protein content only increased for HIITΔ90 (ES: 1.49, × / ÷ 1.42). Repeated-sprint ability (5 × 6-s sprints; 24 s passive rest) improved similarly for both groups. Power at the lactate threshold only improved for HIITΔ20 (ES: 0.49; 90% confidence limits ± 0.38), whereas peak O 2 uptake did not change for either group. Detraining was characterized by the loss of adaptations for all of the proteins measured and for repeated-sprint ability 6 wk after removing the stimulus of HIIT. In conclusion, 4 wk of HIIT induced improvements in each of the acid-base transport protein families, but, remarkably, a 40

SnO and SnO·CoO nanocomposite as high capacity anode materials for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Das, B., E-mail: bijoy822000@gmail.com; Reddy, M.V.; Chowdari, B.V.R, E-mail: phychowd@nus.edu.sg

2016-02-15

Highlights: • The preparation methods are simple, low cost and can be scaled up for large production. • SnO is cheap, non-toxic and eco-friendly. • SnO shows high reversible capacity (Theoretical reversible capacity: 875 mA h g{sup −1}). • We showed high reversible capacity and columbic efficiency for SnO and SnO based composites. • We addressed the capacity degradation by introducing secondary phase (CoO and CNT etc.) - Abstract: We prepared SnO nanoparticles (SnO–S) and SnO·CoO nanocomposites (SnO·CoO–B) as anodes for lithium ion batteries (LIBs) by chemical and ball-milling approaches, respectively. They are characterized by X-ray diffraction and TEM techniques. The Li- storage performance are evaluated by galvanostatic cycling and cyclic voltammetry. The SnO–S and SnO·CoO–B showed improved cycling performance due to their finite particle size (i.e. nano-size) and presence of secondary phase (CoO). Better cycling stability is noticed for SnO·CoO–B with the expense of their reversible capacity. Also, addition of carbon nanotubes (CNT) to SnO–S further improved the cycling performance of SnO–S. When cycled at 60 mA g{sup −1}, the first-cycle reversible capacities of 635, 590 and 460 (±10) mA h g{sup −1} are noticed for SnO–S, SnO@CNT and SnO·CoO–B, respectively. The capacity fading observed are 3.7 and 1.8 mA h g{sup −1} per cycle for SnO–S and SnO@CNT, respectively; whereas 1–1.2 mA h g{sup −1} per cycle for SnO·CoO–B. All the samples show high coulombic efficiency, 96–98% in the range of 5–50 cycles.

Rigorous Screening Technology for Identifying Suitable CO2 Storage Sites II

Energy Technology Data Exchange (ETDEWEB)

George J. Koperna Jr.; Vello A. Kuuskraa; David E. Riestenberg; Aiysha Sultana; Tyler Van Leeuwen

2009-06-01

This report serves as the final technical report and users manual for the 'Rigorous Screening Technology for Identifying Suitable CO2 Storage Sites II SBIR project. Advanced Resources International has developed a screening tool by which users can technically screen, assess the storage capacity and quantify the costs of CO2 storage in four types of CO2 storage reservoirs. These include CO2-enhanced oil recovery reservoirs, depleted oil and gas fields (non-enhanced oil recovery candidates), deep coal seems that are amenable to CO2-enhanced methane recovery, and saline reservoirs. The screening function assessed whether the reservoir could likely serve as a safe, long-term CO2 storage reservoir. The storage capacity assessment uses rigorous reservoir simulation models to determine the timing, ultimate storage capacity, and potential for enhanced hydrocarbon recovery. Finally, the economic assessment function determines both the field-level and pipeline (transportation) costs for CO2 sequestration in a given reservoir. The screening tool has been peer reviewed at an Electrical Power Research Institute (EPRI) technical meeting in March 2009. A number of useful observations and recommendations emerged from the Workshop on the costs of CO2 transport and storage that could be readily incorporated into a commercial version of the Screening Tool in a Phase III SBIR.

Anolyte recycling enhanced bioelectricity generation of the buffer-free single-chamber air-cathode microbial fuel cell.

Science.gov (United States)

Ren, Yueping; Chen, Jinli; Shi, Yugang; Li, Xiufen; Yang, Na; Wang, Xinhua

2017-11-01

Anolyte acidification is an inevitable restriction for the bioelectricity generation of buffer-free microbial fuel cells (MFCs). In this work, acidification of the buffer-free KCl anolyte has been thoroughly eliminated through anolyte recycling. The accumulated HCO 3 - concentration in the recycled KCl anolyte was above 50mM, which played as natural buffer and elevated the anolyte pH to above 8. The maximum power density (P max ) increased from 322.9mWm -2 to 527.2mWm -2 , which is comparable with the phosphate buffered MFC. Besides Geobacter genus, the gradually increased anolyte pH and conductivity induced the growing of electrochemically active Geoalkalibacter genus, in the anode biofilm. Anolyte recycling is a feasible strategy to strengthen the self-buffering capacity of buffer-free MFCs, thoroughly eliminate the anolyte acidification and prominently enhance the electric power. Copyright © 2017 Elsevier Ltd. All rights reserved.

Methods to Assess Geological CO2 Storage Capacity: Status and Best Practice

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-01

To understand the emission reduction potential of carbon capture and storage (CCS), decision makers need to understand the amount of CO2 that can be safely stored in the subsurface and the geographical distribution of storage resources. Estimates of storage resources need to be made using reliable and consistent methods. Previous estimates of CO2 storage potential for a range of countries and regions have been based on a variety of methodologies resulting in a correspondingly wide range of estimates. Consequently, there has been uncertainty about which of the methodologies were most appropriate in given settings, and whether the estimates produced by these methods were useful to policy makers trying to determine the appropriate role of CCS. In 2011, the IEA convened two workshops which brought together experts for six national surveys organisations to review CO2 storage assessment methodologies and make recommendations on how to harmonise CO2 storage estimates worldwide. This report presents the findings of these workshops and an internationally shared guideline for quantifying CO2 storage resources.

Aminopropyl-functionalized mesoporous silicas as CO{sub 2} adsorbents

Energy Technology Data Exchange (ETDEWEB)

Knowles, Gregory P.; Graham, Jeremy V.; Delaney, Seamus W.; Chaffee, Alan L. [School of Chemistry, PO Box 23, Monash University, Vic 3800 (Australia)

2005-10-15

A range of mesoporous silica substrates were functionalized with 3-aminopropyltrimethoxysilane to form hybrid products suitable for carbon dioxide adsorption. A 'cylindrical pore' model was employed to characterize the extent of surface modification per unit substrate surface area and to permit its comparison on a common basis. The extent of surface functionalisation varied with substrate morphology. Combined DTA/TGA was used to characterise CO{sub 2} adsorption. Substantial reversible CO{sub 2} adsorption capacities were observed under anhydrous conditions (at 20 {sup o}C). In the presence of water, CO{sub 2} capacity was enhanced, but the rate of desorption was diminished. (author)

Biomass carbon, nitrogen and phosphorus stocks in hybrid poplar buffers, herbaceous buffers and natural woodlots in the riparian zone on agricultural land.

Science.gov (United States)

Fortier, Julien; Truax, Benoit; Gagnon, Daniel; Lambert, France

2015-05-01

In many temperate agricultural areas, riparian forests have been converted to cultivated land, and only narrow strips of herbaceous vegetation now buffer many farm streams. The afforestation of these riparian zones has the potential to increase carbon (C) storage in agricultural landscapes by creating a new biomass sink for atmospheric CO2. Occurring at the same time, the storage of nitrogen (N) and phosphorus (P) in plant biomass, is an important water quality function that may greatly vary with types of riparian vegetation. The objectives of this study were (1) to compare C, N and P storage in aboveground, belowground and detrital biomass for three types of riparian vegetation cover (9-year-old hybrid poplar buffers, herbaceous buffers and natural woodlots) across four agricultural sites and (2) to determine potential vegetation cover effects on soil nutrient supply rate in the riparian zone. Site level comparisons suggest that 9-year-old poplar buffers have stored 9-31 times more biomass C, 4-10 times more biomass N, and 3-7 times more biomass P than adjacent non managed herbaceous buffers, with the largest differences observed on the more fertile sites. The conversion of these herbaceous buffers to poplar buffers could respectively increase C, N and P storage in biomass by 3.2-11.9 t/ha/yr, 32-124 kg/ha/yr and 3.2-15.6 kg/ha/yr, over 9 years. Soil NO3 and P supply rates during the summer were respectively 57% and 66% lower in poplar buffers than in adjacent herbaceous buffers, potentially reflecting differences in nutrient storage and cycling between the two buffer types. Biomass C ranged 49-160 t/ha in woodlots, 33-110 t/ha in poplar buffers and 3-4 t/ha in herbaceous buffers. Similar biomass C stocks were found in the most productive poplar buffer and three of the four woodlots studied. Given their large and varied biomass C stocks, conservation of older riparian woodlots is equally important for C balance management in farmland. In addition, the

Capturing [11C]CO2 for use in aqueous applications

International Nuclear Information System (INIS)

Vandehey, Nicholas T.; O’Neil, James P.

2014-01-01

We present a simple method for trapping [ 11 C]CO 2 gas and releasing it into a buffered solution using an ion-exchange cartridge. Sodium hydroxide cartridges captured >99% of [ 11 C]CO 2 following NaOH activation. A sodium bicarbonate solution eluted >99% of trapped radioactivity. Trapping [ 11 C]CO 2 directly in small volumes of several solutions was less effective than cartridge methods. The recommended methods allow for fast and simple production of highly concentrated carbon-11 containing aqueous solutions for use in filling phantoms, calibrating detectors, or (bio)geochemical experiments. - Highlights: • An ion exchange resin can trap [ 11 C]CO 2 gas and release it with saturated bicarbonate. • Elution from cartridge requires as little as 300 µL volume, with eluant at pH=10. • SPE trap-and-release provided better results than trapping in solution

Improvement of the energy conversion efficiency of Cu(In,Ga)Se{sub 2} solar cells using an additional Zn(S,O) buffer

Energy Technology Data Exchange (ETDEWEB)

Choi, In-Hwan, E-mail: ihchoi@cau.ac.kr [Chung-Ang University, Department of Physics, Seoul 156-756 (Korea, Republic of); Choi, Chul-Hwan [LG Innotek, Gyeonggi-do, Ansan-si 426-791 (Korea, Republic of)

2012-12-15

CuInGaSe{sub 2} (CIGS) solar cells were prepared with two different buffer structures. Sample A had a single, thin CdS buffer, {approx} 25 nm in thickness, and Sample B had a very thin CdS buffer (< 5 nm thickness) with an additional Zn(S,O) buffer layer. The CIGS and CdS layers in these samples were prepared using a 3-step co-evaporation method and chemical bath deposition, respectively, whereas the additional Zn(S,O) buffer and boron (B)-doped ZnO window layer were prepared by metal organic chemical vapor deposition. The current-voltage curves, quantum efficiency, depth profile by secondary ion mass spectrometry, and transmission electron microscopy images of both samples were analyzed. Sample B showed greater open circuit voltage than Sample A, whereas the short circuit current of Sample B was less than that of Sample A. Even though the energy conversion efficiency is not markedly improved compared to the highest recorded value of each sample, it was quite obvious throughout this experiment that the additional buffer cells had higher reliability and homogeneous properties than CdS buffer cells. - Highlights: Black-Right-Pointing-Pointer CuInGaSe{sub 2} solar cells were prepared with two different buffer structures. Black-Right-Pointing-Pointer One sample had a CdS buffer only, and the other had a very thin CdS and Zn(S,O) buffer. Black-Right-Pointing-Pointer Additional Zn(S,O) buffer was prepared by metal organic chemical vapor deposition. Black-Right-Pointing-Pointer Energy conversion efficiency of the additional buffer cells was slightly improved. Black-Right-Pointing-Pointer CdS/Zn(S,O) cells had higher reliability and homogeneous properties than CdS cells.

CO2-neutral fuels

Directory of Open Access Journals (Sweden)

Goede A. P. H.

2015-01-01

Full Text Available The need for storage of renewable energy (RE generated by photovoltaic, concentrated solar and wind arises from the fact that supply and demand are ill-matched both geographically and temporarily. This already causes problems of overcapacity and grid congestion in countries where the fraction of RE exceeds the 20% level. A system approach is needed, which focusses not only on the energy source, but includes conversion, storage, transport, distribution, use and, last but not least, the recycling of waste. Furthermore, there is a need for more flexibility in the energy system, rather than relying on electrification, integration with other energy systems, for example the gas network, would yield a system less vulnerable to failure and better adapted to requirements. For example, long-term large-scale storage of electrical energy is limited by capacity, yet needed to cover weekly to seasonal demand. This limitation can be overcome by coupling the electricity net to the gas system, considering the fact that the Dutch gas network alone has a storage capacity of 552 TWh, sufficient to cover the entire EU energy demand for over a month. This lecture explores energy storage in chemicals bonds. The focus is on chemicals other than hydrogen, taking advantage of the higher volumetric energy density of hydrocarbons, in this case methane, which has an approximate 3.5 times higher volumetric energy density. More importantly, it allows the ready use of existing gas infrastructure for energy storage, transport and distribution. Intermittent wind electricity generated is converted into synthetic methane, the Power to Gas (P2G scheme, by splitting feedstock CO2 and H2O into synthesis gas, a mixture of CO and H2. Syngas plays a central role in the synthesis of a range of hydrocarbon products, including methane, diesel and dimethyl ether. The splitting is accomplished by innovative means; plasmolysis and high-temperature solid oxygen electrolysis. A CO2-neutral fuel

Working memory capacity of biological movements predicts empathy traits.

Science.gov (United States)

Gao, Zaifeng; Ye, Tian; Shen, Mowei; Perry, Anat

2016-04-01

Working memory (WM) and empathy are core issues in cognitive and social science, respectively. However, no study so far has explored the relationship between these two constructs. Considering that empathy takes place based on the others' observed experiences, which requires extracting the observed dynamic scene into WM and forming a coherent representation, we hypothesized that a sub-type of WM capacity, i.e., WM for biological movements (BM), should predict one's empathy level. Therefore, WM capacity was measured for three distinct types of stimuli in a change detection task: BM of human beings (BM; Experiment 1), movements of rectangles (Experiment 2), and static colors (Experiment 3). The first two stimuli were dynamic and shared one WM buffer which differed from the WM buffer for colors; yet only the BM conveyed social information. We found that BM-WM capacity was positively correlated with both cognitive and emotional empathy, with no such correlations for WM capacity of movements of rectangles or of colors. Thus, the current study is the first to provide evidence linking a specific buffer of WM and empathy, and highlights the necessity for considering different WM capacities in future social and clinical research.

Preparation and characterization of aminated graphite oxide for CO2 capture

International Nuclear Information System (INIS)

Zhao Yunxia; Ding Huiling; Zhong Qin

2012-01-01

Adsorption with solid sorbents is one of the most promising options for postcombustion carbon dioxide (CO 2 ) capture. In this study, aminated graphite oxide used for CO 2 adsorption was synthesized, based on the intercalation reaction of graphite oxide (GO) with amines, including ethylenediamine (EDA), diethylenetriamine (DETA) and triethylene tetramine (TETA). The structural information, surface chemistry and thermal behavior of the adsorbent samples were characterized by X-ray powder diffraction (XRD), infrared spectroscopy (IR), transmission electron microscope (TEM), elemental analysis, particle size analysis, nitrogen adsorption as well as differential thermal and thermogravimetric analysis (DSC-TGA). CO 2 capture was investigated by dynamic adsorption experiments with N 2 -CO 2 mixed gases at 30 °C. The three kinds of graphite oxide samples modified by excess EDA, DETA and TETA showed similar adsorption behaviors seen from their breakthrough curves. Among them, the sample aminated by EDA exhibited the highest adsorption capacity with the longest breakthrough time of CO 2 . Before saturation, its adsorption capacity was up to 53.62 mg CO 2 /g sample. In addition, graphite oxide samples modified by different amount of EDA (EDA/GO raw ratio 10 wt%, 50 wt% and 100 wt%) were prepared in the ethanol. Their CO 2 adsorption performance was investigated. The experimental results demonstrated that graphite oxide with 50 wt% EDA had the largest adsorption capacity 46.55 mg CO 2 /g sample.

CO2 capture by Li-functionalized silicene

KAUST Repository

Zhu, Jiajie

2016-05-18

CO2 capture and storage technology is of key importance to reduce the greenhouse effect. By its large surface area and sp3 hybridization, Li-functionalized silicene is demonstrated to be a promising CO2 absorbent that is stable up to at least 500 K and has a very high storage capacity of 28.6 mol/kg (55.7 wt%). The adsorption energy of CO2 on Li-functionalized silicene is enhanced as compared to pristine silicene, to attain an almost ideal value that still facilitates easy release. In addition, the band gap is found to change sensitively with the CO2 coverage. (© 2016 WILEY-VCH Verlag GmbH &Co. KGaA, Weinheim). © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Effects of freshwater Synechococcus sp. cyanobacteria pH buffering on CaCO3 precipitation: Implications for CO2 sequestration

International Nuclear Information System (INIS)

Martinez, Raul E.; Weber, Sebastian; Grimm, Christian

2016-01-01

In the present study, a mixed-flow steady-state bio-reactor was designed to biomineralize CO 2 as a consequence of photosynthesis from active Synechococcus sp. Dissolved CO 2 , generated by constant air bubbling of inorganic and cyanobacteria stock solutions, was the only source of inorganic carbon. The release of hydroxide ion by cyanobacteria from photosynthesis maintained highly alkaline pH conditions. In the presence of Ca 2+ and carbonate species, this led to calcite supersaturation under steady state conditions. Ca 2+ remained constant throughout the experiments showing the presence of steady state conditions. Similarly, the Synechococcus sp. biomass concentration remained stable within uncertainty. A gradual pH decrease was observed for the highest Ca 2+ condition coinciding with the formation of CaCO 3 . The high degree of supersaturation, under steady-state conditions, contributed to the stabilization of calcite and maintained a constant driving force for the mineral nucleation and growth. For the highest Ca 2+ condition a fast crystal growth rate was consistent with rapid calcite precipitation as suggested further by affinity calculations. Although saturation state based kinetic precipitation models cannot accurately reflect the controls on crystal growth kinetics or reliably predict growth mechanisms, the relatively reaction orders obtained from modeling of calcite precipitation rates as function of decreasing carbonate concentration suggest that the precipitation occurred via surface-controlled rate determining reactions. These high reaction orders support in addition the hypothesis that crystal growth proceeded through complex surface controlled mechanisms. In conclusion, the steady state supersaturated conditions generated by a constant cyanobacteria biomass and metabolic activity strongly suggest that these microorganisms could be used for the development of efficient CO 2 sequestration methods in a controlled large-scale environment. - Highlights: �

High efficiency nanocomposite sorbents for CO2 capture based on amine-functionalized mesoporous capsules

KAUST Repository

Qi, Genggeng; Wang, Yanbing; Estevez, Luis; Duan, Xiaonan; Anako, Nkechi; Park, Ah-Hyung Alissa; Li, Wen; Jones, Christopher W.; Giannelis, Emmanuel P.

2011-01-01

A novel high efficiency nanocomposite sorbent for CO2 capture has been developed based on oligomeric amine (polyethylenimine, PEI, and tetraethylenepentamine, TEPA) functionalized mesoporous silica capsules. The newly synthesized sorbents exhibit extraordinary capture capacity up to 7.9 mmol g-1 under simulated flue gas conditions (pre-humidified 10% CO 2). The CO2 capture kinetics were found to be fast and reached 90% of the total capacities within the first few minutes. The effects of the mesoporous capsule features such as particle size and shell thickness on CO2 capture capacity were investigated. Larger particle size, higher interior void volume and thinner mesoporous shell thickness all improved the CO2 capacity of the sorbents. PEI impregnated sorbents showed good reversibility and stability during cyclic adsorption-regeneration tests (50 cycles). © 2011 The Royal Society of Chemistry.

Geomechanical behavior of the reservoir and caprock system at the In Salah CO2 storage project.

Science.gov (United States)

White, Joshua A; Chiaramonte, Laura; Ezzedine, Souheil; Foxall, William; Hao, Yue; Ramirez, Abelardo; McNab, Walt

2014-06-17

Almost 4 million metric tons of CO2 were injected at the In Salah CO2 storage site between 2004 and 2011. Storage integrity at the site is provided by a 950-m-thick caprock that sits above the injection interval. This caprock consists of a number of low-permeability units that work together to limit vertical fluid migration. These are grouped into main caprock units, providing the primary seal, and lower caprock units, providing an additional buffer and some secondary storage capacity. Monitoring observations at the site indirectly suggest that pressure, and probably CO2, have migrated upward into the lower portion of the caprock. Although there are no indications that the overall storage integrity has been compromised, these observations raise interesting questions about the geomechanical behavior of the system. Several hypotheses have been put forward to explain the measured pressure, seismic, and surface deformation behavior. These include fault leakage, flow through preexisting fractures, and the possibility that injection pressures induced hydraulic fractures. This work evaluates these hypotheses in light of the available data. We suggest that the simplest and most likely explanation for the observations is that a portion of the lower caprock was hydrofractured, although interaction with preexisting fractures may have played a significant role. There are no indications, however, that the overall storage complex has been compromised, and several independent data sets demonstrate that CO2 is contained in the confinement zone.

Contributions of separate reactions to the acid-base buffering of soils in brook floodplains (Central Forest State Reserve)

Science.gov (United States)

Sokolova, T. A.; Tolpeshta, I. I.; Rusakova, E. S.

2016-04-01

The acid-base buffering of gleyic gray-humus soils developed in brook floodplains and undisturbed southern-taiga landscapes has been characterized by the continuous potentiometric titration of soil water suspensions. During the interaction with an acid, the major amount of protons (>80%) is consumed for the displacement of exchangeable bases and the dissolution of Ca oxalates. In the O and AY horizons, Mn compounds make the major contribution (2-15%) to the acid buffering. The buffer reactions with the participation of Al compounds make up from 0.5 to 1-2% of the total buffering capacity, and the protonation of the surface OH groups of kaolinite consumes 2-3% of the total buffering capacity. The deprotonation of OH groups on the surface of Fe hydroxides (9-43%), the deprotonation of OH groups on the surface of illite crystals (3-19%), and the dissolution of unidentified aluminosilicates (9-14%) are the most significant buffer reactions whose contributions have been quantified during the interaction with a base. The contribution of the deprotonation of OH groups on the surface of kaolinite particles is lower (1-5%) because of the small specific surface area of this mineral, and that of the dissolution of Fe compounds is insignificant. In the AY horizon, the acid and base buffering of soil in the rhizosphere is higher than beyond the rhizosphere because of the higher contents of organic matter and nonsilicate Fe and Al compounds.

LOT Project long term test of buffer material at the Aespoe HRL

International Nuclear Information System (INIS)

Karnland, O.; Olsson, S.; Dueck, A.; Birgersson, M.; Nilsson, U.; Hernan-Haakansson, T.; Pedersen, K.; Eriksson, S.; Eriksen, T.; Eriksson, S.; Rosborg, B.; Muurinen, A.; Rousset, D.; Mosser-Ruck, R.; Cathelineau, M.; Villieras, F.; Pelletier, M.; Kaufold, S.; Dohrmann, R.; Fernandez, R.; Maeder, U.; Koroleva, M.

2010-01-01

Document available in extended abstract form only. Bentonite clay has been proposed as buffer material in several concepts for HLW repositories. The decaying spent fuel in the HLW canisters will increase temperature of the bentonite buffer. A number of laboratory test series, made by different research groups, have resulted in various bentonite alteration models. According to these models no significant alteration of the buffer is expected to take place at the prevailing physico-chemical conditions in the proposed Swedish KBS-3 repository, neither during, nor after water saturation. The ongoing LOT test series is focused on quantifying the mineralogical alteration in the buffer in a repository like environment at the Aespoe HRL. Further, buffer related processes concerning bacterial survival/activity, cation transport, and copper corrosion are studied. In total, the LOT test series includes seven test parcels, of which three are exposed to standard KBS-3 conditions and four test parcels are exposed to adverse conditions. Each test parcel contains a central Cu-tube surrounded by bentonite cylinder rings with a diameter of 30 cm, additional test material (Cu coupons, 60 Co tracers, bacteria etc) and instruments. Electrical heaters were place within the copper tube in order to simulate effect of decaying power from the spent fuel. The entire test parcels were released from the rock after the field exposure by overlapping boring and the bentonite material was analyzed with respect to: - physical properties (water content, density, swelling pressure, hydraulic conductivity, rheology); - mineralogical alteration in the bentonite; - distribution of added substances (e.g diffusional transport of 60 Co); - copper corrosion; - bacterial survival/activity. Two one year tests were started in 1996 and terminated in 1998. The results from tests and analyses are presented in SKB TR-00-22. The remaining four test parcels were installed during the fall 1999 plus one additional one

CO{sub 2} capture using some fly ash-derived carbon materials

Energy Technology Data Exchange (ETDEWEB)

A. Arenillas; K.M. Smith; T.C. Drage; C.E. Snape [University of Nottingham, Nottingham (United Kingdom). Nottingham Fuel and Energy Centre, School of Chemical, Environmental and Mining Engineering

2005-12-01

Adsorption is considered to be one of the more promising technologies for capturing CO{sub 2} from flue gases. For post-combustion capture, the success of such an approach is however dependent on the development of an adsorbent that can operate competitively at relatively high temperatures. In this work, low cost carbon materials derived from fly ash, are presented as effective CO{sub 2} sorbents through impregnation these with organic bases, for example, polyethylenimine aided by polyethylene glycol. The results show that for samples derived from a fly ash carbon concentrate, the CO{sub 2} adsorption capacities were relatively high (up to 4.5 wt%) especially at high temperatures (75{sup o}C), where commercial active carbons relying on physi-sorption have low capacities. The addition of PEG improves the adsorption capacity and reduces the time taken for the sample to reach the equilibrium. No CO{sub 2} seems to remain after desorption, suggesting that the process is fully reversible. 24 refs., 6 figs., 2 tabs.

Modelling distribution of evaporating CO2 in parallel minichannels

DEFF Research Database (Denmark)

Brix, Wiebke; Kærn, Martin Ryhl; Elmegaard, Brian

2010-01-01

The effects of airflow non-uniformity and uneven inlet qualities on the performance of a minichannel evaporator with parallel channels, using CO2 as refrigerant, are investigated numerically. For this purpose a one-dimensional discretised steady-state model was developed, applying well-known empi......The effects of airflow non-uniformity and uneven inlet qualities on the performance of a minichannel evaporator with parallel channels, using CO2 as refrigerant, are investigated numerically. For this purpose a one-dimensional discretised steady-state model was developed, applying well...... to maldistribution of the refrigerant and considerable capacity reduction of the evaporator. Uneven inlet ualities to the different channels show only minor effects on the refrigerant distribution and evaporator capacity as long as the channels are vertically oriented with CO2 flowing upwards. For horizontal...... channels capacity reductions are found for both non-uniform airflow and uneven inlet qualities. For horizontal minichannels the results are very similar to those obtained using R134a as refrigerant....

Synthesis of Co 2SnO 4@C core-shell nanostructures with reversible lithium storage

Science.gov (United States)

Qi, Yue; Du, Ning; Zhang, Hui; Wu, Ping; Yang, Deren

This paper reports the synthesis of Co 2SnO 4@C core-shell nanostructures through a simple glucose hydrothermal and subsequent carbonization approach. The as-synthesized Co 2SnO 4@C core-shell nanostructures have been applied as anode materials for lithium-ion batteries, which exhibit improved cyclic performance compared to pure Co 2SnO 4 nanocrystals. The carbon matrix has good volume buffering effect and high electronic conductivity, which may be responsible for the improved cyclic performance.

On buffer overflow duration in a finite-capacity queueing system with multiple vacation policy

Science.gov (United States)

Kempa, Wojciech M.

2017-12-01

A finite-buffer queueing system with Poisson arrivals and generally distributed processing times, operating under multiple vacation policy, is considered. Each time when the system becomes empty, the service station takes successive independent and identically distributed vacation periods, until, at the completion epoch of one of them, at least one job waiting for service is detected in the buffer. Applying analytical approach based on the idea of embedded Markov chain, integral equations and linear algebra, the compact-form representation for the cumulative distribution function (CDF for short) of the first buffer overflow duration is found. Hence, the formula for the CDF of next such periods is obtained. Moreover, probability distributions of the number of job losses in successive buffer overflow periods are found. The considered queueing system can be efficienly applied in modelling energy saving mechanisms in wireless network communication.

Biomass waste carbon materials as adsorbents for CO2 capture under post-combustion conditions

Directory of Open Access Journals (Sweden)

Elisa M Calvo-Muñoz

2016-05-01

Full Text Available A series of porous carbon materials obtained from biomass waste have been synthesized, with different morphologies and structural properties, and evaluated as potential adsorbents for CO2 capture in post-combustion conditions. These carbon materials present CO2 adsorption capacities, at 25 ºC and 101.3 kPa, comparable to those obtained by other complex carbon or inorganic materials. Furthermore, CO2 uptakes under these conditions can be well correlated to the narrow micropore volume, derived from the CO2 adsorption data at 0 ºC (VDRCO2. In contrast, CO2 adsorption capacities at 25 ºC and 15 kPa are more related to only pores of sizes lower than 0.7 nm. The capacity values obtained in column adsorption experiments were really promising. An activated carbon fiber obtained from Alcell lignin, FCL, presented a capacity value of 1.3 mmol/g (5.7 %wt. Moreover, the adsorption capacity of this carbon fiber was totally recovered in a very fast desorption cycle at the same operation temperature and total pressure and, therefore, without any additional energy requirement. Thus, these results suggest that the biomass waste used in this work could be successfully valorized as efficient CO2 adsorbent, under post-combustion conditions, showing excellent regeneration performance.

Controlling Cooperative CO2 Adsorption in Diamine-Appended Mg2(dobpdc) Metal-Organic Frameworks.

Science.gov (United States)

Siegelman, Rebecca L; McDonald, Thomas M; Gonzalez, Miguel I; Martell, Jeffrey D; Milner, Phillip J; Mason, Jarad A; Berger, Adam H; Bhown, Abhoyjit S; Long, Jeffrey R

2017-08-02

In the transition to a clean-energy future, CO 2 separations will play a critical role in mitigating current greenhouse gas emissions and facilitating conversion to cleaner-burning and renewable fuels. New materials with high selectivities for CO 2 adsorption, large CO 2 removal capacities, and low regeneration energies are needed to achieve these separations efficiently at scale. Here, we present a detailed investigation of nine diamine-appended variants of the metal-organic framework Mg 2 (dobpdc) (dobpdc 4- = 4,4'-dioxidobiphenyl-3,3'-dicarboxylate) that feature step-shaped CO 2 adsorption isotherms resulting from cooperative and reversible insertion of CO 2 into metal-amine bonds to form ammonium carbamate chains. Small modifications to the diamine structure are found to shift the threshold pressure for cooperative CO 2 adsorption by over 4 orders of magnitude at a given temperature, and the observed trends are rationalized on the basis of crystal structures of the isostructural zinc frameworks obtained from in situ single-crystal X-ray diffraction experiments. The structure-activity relationships derived from these results can be leveraged to tailor adsorbents to the conditions of a given CO 2 separation process. The unparalleled versatility of these materials, coupled with their high CO 2 capacities and low projected energy costs, highlights their potential as next-generation adsorbents for a wide array of CO 2 separations.

Long-term effects of ozone on CO2 exchange in peatland microcosms

DEFF Research Database (Denmark)

Haapala, JK; Mörsky, SK; Rinnan, Riikka

2011-01-01

Effects of elevated tropospheric ozone concentration on the CO2 exchange of peatland microcosms and the photosynthetic capacity of the dominating sedge, Eriophorum vaginatum, were studied in a four-year open-field experiment. The net ecosystem CO2 exchange and the dark respiration rate of the mic......Effects of elevated tropospheric ozone concentration on the CO2 exchange of peatland microcosms and the photosynthetic capacity of the dominating sedge, Eriophorum vaginatum, were studied in a four-year open-field experiment. The net ecosystem CO2 exchange and the dark respiration rate...... exchange of the peatland microcosms....

Formation and decomposition of siderite for CO2 treatment

Science.gov (United States)

Y Mora, E.; Sarmiento, A.; Vera, E.; Drozd, V.; Durigyn, A.; Saxena, S.

2017-12-01

In this research work, we studied the conditions for formation and decomposition of siderite FeCO3 from hematite Fe2O3 along with carbon dioxide CO2 at suitable thermodynamic conditions. As reductant agents were used mixtures of two elements, metallic iron and graphite. Best levels of carbonation were found in mixtures with bigger amounts of metallic iron. It was demonstrated that CO2 capture capacity by hematite depends of temperature, CO2 pressure, and reaction time. Temperatures between 100 and 150°C, pressures between 10 and 30bar and reaction times between 1 and 4h were adjusted for analyse the carbonation behaviour; siderite formation was improved by increases of these three variables. There was no carbonation without water in the mixtures, due to kinetic limitations. CO2 capture capacity was calculated from Rietveld refinement results. Using vacuum system and Dielectric Barrier Discharge, DBD plasma, the siderite was decomposed at 300°C, and 320°C respectively. Techniques as X-ray diffraction, and surface area analysis were employed to study the material.

Riparian buffer zones as pesticide filters of no-till crops.

Science.gov (United States)

Aguiar, Terencio R; Bortolozo, F R; Hansel, F A; Rasera, K; Ferreira, M T

2015-07-01

Several studies have pointed to the potential benefits of riparian vegetation as buffer zones for agricultural and industrial pollutants harmful to aquatic ecosystems. However, other studies have called into question its use as an ecological filter, questioning the widths and conditions for which they are effective as a filter. In this work, we have investigated the buffering capacity of the riparian one to retain pesticides in the water-saturated zone, on 27 sites composed by riparian buffer zones with different vegetation structure (woody, shrubs, or grass vegetation) and width (12, 36, and 60 m). Five pesticides were analyzed. The effectiveness of the filtering was largely influenced by the width and vegetation type of the buffer zone. In general, decreasing pesticide removal followed in this order wood > shrubs > grass. The 60 m woody buffer zone was the most effective in the removal of all the pesticides. Only atrazine was detected in this case (0.3 μg L(-1)). Furthermore, a linear correlation (R (2) > 0.97) was observed in their removal for all compounds and buffer zones studied. Thus, preserving the woody vegetation in the riparian zone is important for watershed management and groundwater quality in the no-tillage system in temperate climate.

Development of New Potassium Carbonate Sorbent for CO2 Capture under Real Flue Gas Conditions

Directory of Open Access Journals (Sweden)

Javad Esmaili

2014-07-01

Full Text Available In this paper, the development of a new potassium carbonateon alumina support sorbent prepared by impregnating K2CO3 with an industrial grade of Al2O3 support was investigated. The CO2 capture capacity was measured using real flue gas with 8% CO2 and 12% H2O in a fixed-bed reactor at a temperature of 65 °C using breakthrough curves. The developed sorbent showed an adsorption capacity of 66.2 mgCO2/(gr sorbent. The stability of sorbent capture capacity was higher than the reference sorbent. The SO2 impurity decreased sorbent capacity about 10%. The free carbon had a small effect on sorbent capacity after 5 cycles. After 5 cycles of adsorption and regeneration, the changes in the pore volume and surface area were 0.020 cm3/gr and 5.5 m2/gr respectively. Small changes occurred in the pore size distribution and surface area of sorbent after 5 cycles.

A study of the efficiency of different spectrochemical buffers applied to the uranium ore analysis

International Nuclear Information System (INIS)

Roca, M.; Diaz Guerra, J. P.

1981-01-01

A direct-reading emission spectroscopy method allowing the determination of Al, Ca, Fe, Mg, Mn, Na, P, Si and Ti in geological materials, that are of interest for the prospecting and recovery of uranium, is proposed. Direct-current are between graphite electrodes Is used as the excitation source. Efficiency of Ag 2 O, BaCO 3 , Bi 2 O 3 , CuF 2 , CuO, Ga 2 0 3 , Ge0 2 , graphite, K 2 CO 3 , H 2 B 4 O 7 , Li 2 CO 3 , Ni, PbS, Sb 2 o 4 , SrC0 3 , Ti 2 O 3 and ZnO as spectrochemical buffers has been studied. It has been inferred that through a sample dilution with Li 2 CO 3 , SrC0 3 and graphite powder in the rations 1:10:10:20, respectively, the highest reduction of the matrix effects is achieved. Phosphorus determination Is better performed with PbS as spectrochemical buffer Instead of the indicated above. The action of the selected compounds Is completed by using Co, In, Li and Sr as internal standards, and, as a whole, satisfactory accuracy and reproducibility are attained. (Author) 7 refs

Development of TRPN dendrimer-modified disordered mesoporous silica for CO{sub 2} capture

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaoyun; Zhang, Sisi; Qin, Hongyan; Wu, Wei, E-mail: wuweiupc@upc.edu.cn

2014-08-15

Highlights: • A novel series of TRPN dendrimers are synthesized. • Structurally disordered mesoporous silica was used to develop the CO{sub 2} adsorbent. • The CO{sub 2} adsorption capacity is relatively high. • The sorbent exhibits a high stability after 12 cycling runs. • The sorbent achieves complete desorption at low temperature (60 °C). - Abstract: A novel series of tri(3-aminopropyl) amine (TRPN) dendrimers were synthesized and impregnated on structurally disordered mesoporous silica (DMS) to generate CO{sub 2} adsorbents (TS). The physicochemical and adsorption properties of the adsorbents before and after dendrimer modification were characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and N{sub 2} adsorption–desorption (N{sub 2}-BET) techniques. CO{sub 2} adsorption–desorption tests indicated that the sorbent demonstrates high CO{sub 2} adsorption capacity (138.1 mg g{sup −1} for G1 sample TS-G1-3CN-50 and 91.7 mg g{sup −1} for G2 sample TS-G2-6CN-50), and can completely desorb CO{sub 2} under vacuum at 60 °C. Its CO{sub 2} adsorption capacity at 25 °C increases with the amine loading, achieving the highest adsorption capacity (140.6 mg g{sup −1} for TS-G1-3CN) at 60%. The developed TS materials exhibited excellent cycling stability. After 12 consecutive adsorption–desorption runs, TS-G1-3CN-50 shows an adsorption capacity of 136.0 mg g{sup −1}, retaining 98.5% of its original value.

Lean buffering in serial production lines with Bernoulli machines

Directory of Open Access Journals (Sweden)

A. B. Hu

2006-01-01

Full Text Available Lean buffering is the smallest buffer capacity necessary to ensure the desired production rate of a manufacturing system. In this paper, analytical methods for selecting lean buffering in serial production lines are developed under the assumption that the machines obey the Bernoulli reliability model. Both closed-form expressions and recursive approaches are investigated. The cases of identical and nonidentical machines are analyzed. Results obtained can be useful for production line designers and production managers to maintain the required production rate with the smallest possible inventories.

Social Buffering of Stress in Development: A Career Perspective

Science.gov (United States)

Gunnar, Megan R.

2016-01-01

This review provides a broad overview of my research group's work on social buffering in human development in the context of the field. Much of the focus is on social buffering of the hypothalamic-pituitary-adrenocortical (HPA) system, one of the two major arms of the mammalian stress system. This focus reflects the centrality of the HPA system in research on social buffering in the fields of developmental psychobiology and developmental science. However, buffering of the cardiovascular and autonomic nervous system is also discussed. The central developmental question in this area derives from attachment theory which argues that the infant's experience of stress and arousal regulation in the context of her early attachment relationships is not an immature form of social buffering experienced in adulthood, but rather the foundation out of which individual differences in the capacity to gain stress relief from social partners emerge. The emergence of social buffering in infancy, changes in social buffering throughout childhood and adolescence, the influence of early experience on later individual differences in social buffering, and critical gaps in our knowledge are described. PMID:28544861

Characterization of Qatar's surface carbonates for CO2 capture and thermochemical energy storage

Science.gov (United States)

Kakosimos, Konstantinos E.; Al-Haddad, Ghadeer; Sakellariou, Kyriaki G.; Pagkoura, Chrysa; Konstandopoulos, Athanasios G.

2017-06-01

Samples of surface carbonates were collected from three different areas of the Qatar peninsula. We employed material characterization techniques to examine the morphology and composition of the samples, while their CO2 capture capacity was assessed via multiple successive calcination-carbonation cycles. Our samples were mainly calcite and dolomite based. Calcite samples showed higher initial capacity of around 11 mmol CO2 g-1 which decayed rapidly to less than 2 mmol CO2 g-1. On the other hand, dolomite samples showed an excellent stability (˜15 cycles) with a capacity of 6 mmol CO2 g-1. The performance of the dolomite samples is better compared to other similar natural samples, from literature. A promising result for future studies towards improving their performance by physical and chemical modification.

Preparation of granular activated carbons from yellow mombin fruit stones for CO2 adsorption.

Science.gov (United States)

Fiuza, Raildo Alves; Medeiros de Jesus Neto, Raimundo; Correia, Laise Bacelar; Carvalho Andrade, Heloysa Martins

2015-09-15

Stones of yellow mombin, a native fruit of the tropical America and West Indies, were used as starting materials to produce activated carbons, subsequently used as adsorbent for CO2 capture. The carbonaceous materials were either chemically activated with HNO3, H3PO4 and KOH or physically activated with CO2. The carbon samples were characterized by SEM, EDX, TG/DTA, Raman spectroscopy, physical adsorption for textural analysis and by acid-base titrations. The CO2 adsorption capacity and adsorption cycles were investigated by TG. The results indicate that the capacity of CO2 adsorption may be maximized on highly basic surfaces of micropores smaller than 1 nm. The KOH activated carbon showed high and stable capacity of CO2 adsorption after 10 cycles. Copyright © 2015 Elsevier Ltd. All rights reserved.

Oxygen Storage Capacity and Oxygen Mobility of Co-Mn-Mg-Al Mixed Oxides and Their Relation in the VOC Oxidation Reaction

Directory of Open Access Journals (Sweden)

María Haidy Castaño

2015-05-01

Full Text Available Co-Mn-Mg-Al oxides were synthesized using auto-combustion and co-precipitation techniques. Constant ratios were maintained with (Co + Mn + Mg/Al equal to 3.0, (Co + Mn/Mg equal to 1.0 and Co/Mn equal to 0.5. The chemical and structural composition, redox properties, oxygen storage capacity and oxygen mobility were analyzed using X-ray fluorescence (XRF, X-ray diffraction (XRD, Raman spectroscopy, scanning electron microscopy (SEM, temperature-programmed reduction of hydrogen (H2-TPR, oxygen storage capacity (OSC, oxygen storage complete capacity (OSCC and isotopic exchange, respectively. The catalytic behavior of the oxides was evaluated in the total oxidation of a mixture of 250 ppm toluene and 250 ppm 2-propanol. The synthesis methodology affected the crystallite size, redox properties, OSC and oxide oxygen mobility, which determined the catalytic behavior. The co-precipitation method got the most active oxide in the oxidation of the volatile organic compound (VOC mixture because of the improved mobility of oxygen and ability to favor redox processes in the material structure.

Preliminary findings on the correlation of saliva pH, buffering capacity, flow rate and consistency in relation to waterpipe tobacco smoking

OpenAIRE

Khemiss, Mehdi; Ben Khelifa, Mohamed; Ben Saad, Helmi

2017-01-01

ABSTRACT The aim of the present comparative study was to compare some salivary characteristics between exclusive waterpipe smokers (EWPS) and non-smokers. 72 males (36 EWPS) were recruited. The volume of stimulated saliva was determined and divided by the duration of saliva collection. The pH was measured directly using a pH meter. The buffering capacity was determined using a quantitative method which involved the addition of 10 ?l HCl. Up to a total of 160 ?L was titrated up to obtain a pH ...

Nonthermal inactivation of Escherichia coli K12 in buffered peptone water using a pilot-plant scale supercritical carbon dioxide system with gas-liquid porous metal contractor

Science.gov (United States)

This study evaluated the effectiveness of a supercritical carbon dioxide (SCCO2) system, with a gas-liquid CO2 contactor, for reducing Escherichia coli K12 in diluted buffered peptone water. 0.1% (w/v) buffered peptone water inoculated with E. coli K12 was processed using the SCCO2 system at CO2 con...

Synthesis and electrochemical characterization of LiCo_1_/_3Fe_2_/_3PO_4/C composite using nano CoFe_2O_4 as precursor

International Nuclear Information System (INIS)

Wu, Kaipeng; Hu, Guorong; Du, Ke; Peng, Zhongdong; Cao, Yanbing

2015-01-01

LiCo_1_/_3Fe_2_/_3PO_4/C composite was synthesized by a solid state method with CoFe_2O_4 as the precursor and glucose as the carbon source. The composite consists of homogeneous Co–Fe distributed LiCo_1_/_3Fe_2_/_3PO_4 with its particles covered by nano-carbon layers, which could prevent the growth of the particles as well as form a fast path for electronic transmission during charging and discharging process. It shows excellent electrochemical performance as the cathode for lithium-ion batteries, which delivers discharge capacities of 154.6, 152.9, 135.4, 122.3, 105.2 and 91.3 mAh g"−"1 at 0.05, 0.1, 0.5, 1, 2 and 5 C, respectively, and retains 94.6% of its initial discharge capacity after 30 cycles at 5 C. - Highlights: • Nano CoFe_2O_4 was prepared by a co-precipitation method. • LiCo_1_/_3Fe_2_/_3PO_4/C composite was synthesized using nano CoFe_2O_4 as a precursor. • Homogeneous Co–Fe distributed LiCo_1_/_3Fe_2_/_3PO_4 is obtained. • LiCo_1_/_3Fe_2_/_3PO_4/C composite exhibits a quite good electrochemical performance.

FY 2000 report on the results of the R and D of the prediction technology for environmental effects of CO2 ocean sequestration. Ocean survey and development of the assessment technology for capacity of CO2 sequestration; 2000 nendo nisanka tanso no kaiyo kakuri ni tomonau kankyo eikyo yosoku gijutsu kenkyu kaihatsu seika hokokusho. Kaiyo chosa oyobi CO2 kakuri noryoku hyoka gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Assuming the dissolution/sequestration of CO2 at the medium-depth sea area around Japan (depth: 1,000-2,000m), the development was being proceeded with of the assessment technology for capacity of CO2 ocean sequestration and the prediction technology of environmental effects at the point of CO2 discharge. In FY 2000, conducted were the ocean survey and the development of assessment technology for CO2 sequestration capacity. In the investigational study, the following three were carried out: 1) survey/observation of the flow field on the line of 165 degrees of east longitude, and acquisition of various data such as the distribution of carbonic acid base substances and the speed of carbon transport; 2) study of the amount of existence of organisms and kind/composition of the medium-depth plankton at the typical observation points; 3) test/experiment actually conducted in the sea area for the experimental equipment for CaCO3 dissolution experimental equipment for studying interactions between the CO2 and CaCO3 dissolved into the medium-depth sea. As to the development of the assessment technology, carried out were the heightening of accuracy of medium-depth ocean circulation models using the inverse method already developed and the estimation of the flow field using the observation data. At the same time, the estimation of the flow field, etc. were conducted using large circulation ocean models. (NEDO)

Labview virtual instruments for calcium buffer calculations.

Science.gov (United States)

Reitz, Frederick B; Pollack, Gerald H

2003-01-01

Labview VIs based upon the calculator programs of Fabiato and Fabiato (J. Physiol. Paris 75 (1979) 463) are presented. The VIs comprise the necessary computations for the accurate preparation of multiple-metal buffers, for the back-calculation of buffer composition given known free metal concentrations and stability constants used, for the determination of free concentrations from a given buffer composition, and for the determination of apparent stability constants from absolute constants. As implemented, the VIs can concurrently account for up to three divalent metals, two monovalent metals and four ligands thereof, and the modular design of the VIs facilitates further extension of their capacity. As Labview VIs are inherently graphical, these VIs may serve as useful templates for those wishing to adapt this software to other platforms.

The midday depression of CO2 assimilation in leaves of Arbutus unedo L.: diurnal changes in photosynthetic capacity related to changes in temperature and humidity.

Science.gov (United States)

Raschke, K; Resemann, A

1986-09-01

Parts of attached leaves of the sclerophyllous shrub Arbutus unedo were subjected to simulated mediterranean days. Gas exchange was recorded in order to recognize the causes of the midday depression in CO2 assimilation. Depressions could be induced in part of a leaf: they were local responses. The CO2-saturation curves of photosynthesis, determined during the morning and afternoon maxima of CO2 assimilation and during the minimum at midday, established that depressions in CO2 assimilation were in one-half of the investigated cases totally caused by reversible reductions in the photosynthetic capacity of the leaves, and in the other half almost totally caused by such reductions. An analysis of 37 daily courses showed that morning reductions and afternoon recoveries of stomatal conductance and rate of photosynthesis occurred simultaneously and in proportion to each other, with the result that the partial pressure of CO2 in the intercellular spaces remained more or less constant. Midday depressions occurred also in detached leaves standing in water. The initiation of a midday depression was not caused by a circadian rhythm, nor was high quantum flux or high temperature a requirement. There was no correlation between the rate of water loss from the leaves, or the amount of water lost, with the degree of reduction of the photosynthetic capacity. However, depressions occurred if an apparent threshold in the water-vapor pressure difference between leaf and air was exceeded. This critical value varied between about 20 and 30 mbar, depending on the leaf investigated. The dominating role of humidity in the induction of the midday depression was further demonstrated when leaf temperature was held constant and the vapor-pressure difference was made to follow the pattern of the mediterranean day: depressions occurred. Depressions however were hardly noticeable when the water-vapor pressure difference was held constant and leaf temperature was allowed to vary. In another set of

Infiltration-driven metamorphism, New England, USA: Regional CO2 fluxes and implications for Devonian climate and extinctions

Science.gov (United States)

Stewart, E. M.; Ague, Jay J.

2018-05-01

We undertake thermodynamic pseudosection modeling of metacarbonate rocks in the Wepawaug Schist, Connecticut, USA, and examine the implications for CO2 outgassing from collisional orogenic belts. Two broad types of pseudosections are calculated: (1) a fully closed-system model with no fluid infiltration and (2) a fluid-buffered model including an H2O-CO2 fluid of a fixed composition. This fluid-buffered model is used to approximate a system open to infiltration by a water-bearing fluid. In all cases the fully closed-system model fails to reproduce the observed major mineral zones, mineral compositions, reaction temperatures, and fluid compositions. The fluid-infiltrated models, on the other hand, successfully reproduce these observations when the XCO2 of the fluid is in the range ∼0.05 to ∼0.15. Fluid-infiltrated models predict significant progressive CO2 loss, peaking at ∼50% decarbonation at amphibolite facies. The closed-system models dramatically underestimate the degree of decarbonation, predicting only ∼15% CO2 loss at peak conditions, and, remarkably, global warming, sea level rise, and, perhaps, extinction in the mid- to late-Devonian.

Nanosized CoO Loaded on Copper Foam for High-Performance, Binder-Free Lithium-Ion Batteries.

Science.gov (United States)

Liao, Mingna; Zhang, Qilun; Tang, Fengling; Xu, Zhiwei; Zhou, Xin; Li, Youpeng; Zhang, Yali; Yang, Chenghao; Ru, Qiang; Zhao, Lingzhi

2018-03-22

The synthesis of nanosized CoO anodes with unique morphologies via a hydrothermal method is investigated. By adjusting the pH values of reaction solutions, nanoflakes (CoO-NFs) and nanoflowers (CoO-FLs) are successfully located on copper foam. Compared with CoO-FLs, CoO-NFs as anodes for lithium ion batteries present ameliorated lithium storage properties, such as good rate capability, excellent cycling stability, and large CoO nanoflakes; CoO nanoflowers; anodes; binder free; lithium ion batteriesreversible capacity. The initial discharge capacity is 1470 mA h g -1 , while the reversible capacity is maintained at 1776 m Ah g -1 after 80 cycles at a current density of 100 mA h g -1 . The excellent electrochemical performance is ascribed to enough free space and enhanced conductivity, which play crucial roles in facilitating electron transport during repetitive Li⁺ intercalation and extraction reaction as well as buffering the volume expansion.

Nanosized CoO Loaded on Copper Foam for High-Performance, Binder-Free Lithium-Ion Batteries

Directory of Open Access Journals (Sweden)

Mingna Liao

2018-03-01

Full Text Available The synthesis of nanosized CoO anodes with unique morphologies via a hydrothermal method is investigated. By adjusting the pH values of reaction solutions, nanoflakes (CoO-NFs and nanoflowers (CoO-FLs are successfully located on copper foam. Compared with CoO-FLs, CoO-NFs as anodes for lithium ion batteries present ameliorated lithium storage properties, such as good rate capability, excellent cycling stability, and large CoO nanoflakes; CoO nanoflowers; anodes; binder free; lithium ion batteriesreversible capacity. The initial discharge capacity is 1470 mA h g−1, while the reversible capacity is maintained at 1776 m Ah g−1 after 80 cycles at a current density of 100 mA h g−1. The excellent electrochemical performance is ascribed to enough free space and enhanced conductivity, which play crucial roles in facilitating electron transport during repetitive Li+ intercalation and extraction reaction as well as buffering the volume expansion.

Flexible Li-CO{sub 2} batteries with liquid-free electrolyte

Energy Technology Data Exchange (ETDEWEB)

Hu, Xiaofei; Li, Zifan; Chen, Jun [Key Laboratory of Advanced Energy Materials Chemistry (Ministry of Education) and State Key Laboratory of Elemento-Organic Chemistry, College of Chemistry, Nankai University, Tianjin (China)

2017-05-15

Developing flexible Li-CO{sub 2} batteries is a promising approach to reuse CO{sub 2} and simultaneously supply energy to wearable electronics. However, all reported Li-CO{sub 2} batteries use liquid electrolyte and lack robust electrolyte/electrodes structure, not providing the safety and flexibility required. Herein we demonstrate flexible liquid-free Li-CO{sub 2} batteries based on poly(methacrylate)/poly(ethylene glycol)-LiClO{sub 4}-3 wt %SiO{sub 2} composite polymer electrolyte (CPE) and multiwall carbon nanotubes (CNTs) cathodes. The CPE (7.14 x 10{sup -2} mS cm{sup -1}) incorporates with porous CNTs cathodes, displaying stable structure and small interface resistance. The batteries run for 100 cycles with controlled capacity of 1000 mAh g{sup -1}. Moreover, pouch-type flexible batteries exhibit large reversible capacity of 993.3 mAh, high energy density of 521 Wh kg{sup -1}, and long operation time of 220 h at different degrees of bending (0-360 ) at 55 C. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Expanding clinical research capacity through a community of practice (CoPER).

Science.gov (United States)

Short, Alison; Jackson, Wanda; Nugus, Peter

2010-01-01

The proposed CoPER project (Community of Practice for Engaging in Research) responds to a need for increased research capacity in a clinical setting. We put forward an argument and a design for a prospective action research project to extend research capacity via an integrated academic and practitioner community of practice in an Emergency Department (ED). This paper explores the research needs of clinicians, articulates the concept of community of practice in light of these needs, and outlines the rationale for considering communities of practice as a potential contributor to building research capacity in a clinical setting. A potential methodology is suggested to test the linkage between research needs, the concept of a community of practice model in a clinical setting, and the contribution of such a model to building research capacity in a clinical setting via the CoPER framework. Combined data from this proposed mixed method action research (survey, focus groups, interviews, observation) are expected to enable the production of a set of facilitators and enablers with a view to building a community of research practice which make the case study transferable to other clinical and non-clinical work settings.

Bicarbonate buffered peritoneal dialysis fluid upregulates angiopoietin-1 and promotes vessel maturation.

Directory of Open Access Journals (Sweden)

Gwendolyn Eich

Full Text Available Ultrafiltration decline is a progressive issue for patients on chronic peritoneal dialysis (PD and can be caused by peritoneal angiogenesis induced by PD fluids. A recent pediatric trial suggests better preservation of ultrafiltration with bicarbonate versus lactate buffered fluid; underlying molecular mechanisms are unknown.Angiogenic cytokine profile, tube formation capacity and Receptor Tyrosine Kinase translocation were assessed in primary human umbilical vein endothelial cells following incubation with bicarbonate (BPDF and lactate buffered (LPDF, pH neutral PD fluid with low glucose degradation product content and lactate buffered, acidic PD fluid with high glucose degradation product content (CPDF. Peritoneal biopsies from age-, PD-vintage- and dialytic glucose exposure matched, peritonitis-free children on chronic PD underwent automated histomorphometry and immunohistochemistry.In endothelial cells angiopoietin-1 mRNA and protein abundance increased 200% upon incubation with BPDF, but decreased by 70% with LPDF as compared to medium control; angiopoietin-2 remained unchanged. Angiopoietin-1/Angiopoietin-2 protein ratio was 15 and 3-fold increased with BPDF compared to LPDF and medium. Time-lapse microscopy with automated network analysis demonstrated less endothelial cell tube formation with BPDF compared to LPDF and CPDF incubation. Receptor Tyrosine Kinase translocated to the cell membrane in BPDF but not in LPDF or CPDF incubated endothelial cells. In children dialyzed with BPDF peritoneal vessels were larger and angiopoietin-1 abundance in CD31 positive endothelium higher compared to children treated with LPDF.Bicarbonate buffered PD fluid promotes vessel maturation via upregulation of angiopoietin-1 in vitro and in children on dialysis. Our findings suggest a molecular mechanism for the observed superior preservation of ultrafiltration capacity with bicarbonate buffered PD fluid with low glucose degradation product content.

Impact of thermal processes on CO2 injectivity into a coal seam

International Nuclear Information System (INIS)

Qu, H Y; Liu, J S; Pan, Z J; Connell, L

2010-01-01

The objective of this study is to investigate how thermal gradients, caused by CO2 injection, expansion and adsorption, affect the permeability and adsorption capacity of coal during CO2 sequestration. A new permeability model is developed in which the concept of elastic modulus reduction ratio is introduced to partition the effective strain between coal matrix and fracture. This model is implemented into a fully coupled mechanical deformation, gas flow and heat transport finite element simulator. To predict the amount of CO2 sequested, the extended Langmuir sorption model is used, with parameters values taken from the literature. The coupled heat and gas flow equations, are solved in COMSOL using the finite element method. The simulation results for a constant volume reservoir demostrate that thermal strain acts to significantly reduce both CO2 injectivity and adsorption capacity. These impacts need to be considered in the calculation of the optimum injection rate and the total sequestration capacity.

Detailed studies of a high-capacity electrode material for rechargeable batteries, Li2MnO3-LiCo(1/3)Ni(1/3)Mn(1/3)O2.

Science.gov (United States)

Yabuuchi, Naoaki; Yoshii, Kazuhiro; Myung, Seung-Taek; Nakai, Izumi; Komaba, Shinichi

2011-03-30

Lithium-excess manganese layered oxides, which are commonly described by the chemical formula zLi(2)MnO(3)-(1-z)LiMeO(2) (Me = Co, Ni, Mn, etc.), are of great importance as positive electrode materials for rechargeable lithium batteries. In this Article, Li(x)Co(0.13)Ni(0.13)Mn(0.54)O(2-δ) samples are prepared from Li(1.2)Ni(0.13)Co(0.13)Mn(0.54)O(2) (or 0.5Li(2)MnO(3)-0.5LiCo(1/3)Ni(1/3)Mn(1/3)O(2)) by an electrochemical oxidation/reduction process in an electrochemical cell to study a reaction mechanism in detail before and after charging across a voltage plateau at 4.5 V vs Li/Li(+). Changes of the bulk and surface structures are examined by synchrotron X-ray diffraction (SXRD), X-ray absorption spectroscopy (XAS), X-ray photoelectron spectroscopy (XPS), and time-of-flight secondary ion mass spectroscopy (SIMS). SXRD data show that simultaneous oxygen and lithium removal at the voltage plateau upon initial charge causes the structural rearrangement, including a cation migration process from metal to lithium layers, which is also supported by XAS. This is consistent with the mechanism proposed in the literature related to the Li-excess manganese layered oxides. Oxygen removal associated with the initial charge on the high voltage plateau causes oxygen molecule generation in the electrochemical cells. The oxygen molecules in the cell are electrochemically reduced in the subsequent discharge below 3.0 V, leading to the extra capacity. Surface analysis confirms the formation of the oxygen containing species, such as lithium carbonate, which accumulates on the electrode surface. The oxygen containing species are electrochemically decomposed upon second charge above 4.0 V. The results suggest that, in addition to the conventional transition metal redox reactions, at least some of the reversible capacity for the Li-excess manganese layered oxides originates from the electrochemical redox reaction of the oxygen molecules at the electrode surface.

Interlaboratory study of the heat capacity of LiNi{sub 1/3}Mn{sub 1/3}Co{sub 1/3}O{sub 2} (NMC111) with layered structure

Energy Technology Data Exchange (ETDEWEB)

Cupid, Damian M.; Gotcu, Petronela [Karlsruhe Institute of Technology (KIT), Eggenstein-Leopoldshafen (Germany). Inst. for Applied Materials - Applied Materials Physics (IAM-AWP); Beutl, Alexander [Vienna Univ. (Austria). Inst. of Inorganic Chemistry - Functional Materials; and others

2017-11-15

An interlaboratory study was performed to determine the heat capacity of an active material for lithium-ion batteries with layered structure and nominal composition LiNi{sub 1/3} . Mn{sub 1/3}Co{sub 1/3}O{sub 2} (NMC111). The commercial sample, which was characterized using powder X-ray diffraction and inductively coupled plasma-optical emission spectroscopy, is single phase (α-NaFeO{sub 2} crystal structure) with a composition of Li{sub 1.02}Ni{sub 0.32}Mn{sub 0.31}Co{sub 0.30}O{sub 2}. Heat capacity measurements of the homogeneous sample were performed at five laboratories using different operators, methods, devices, temperature ranges, gas atmospheres and crucible materials. The experimental procedures from each laboratory are presented and the results of the individual laboratories are analyzed. Based on a comprehensive evaluation of the data from each laboratory, the heat capacity of the NMC111 sample from 315 K to 1 020 K is obtained with an expanded reproducibility uncertainty of less than 1.22 %.

Shared filtering processes link attentional and visual short-term memory capacity limits.

Science.gov (United States)

Bettencourt, Katherine C; Michalka, Samantha W; Somers, David C

2011-09-30

Both visual attention and visual short-term memory (VSTM) have been shown to have capacity limits of 4 ± 1 objects, driving the hypothesis that they share a visual processing buffer. However, these capacity limitations also show strong individual differences, making the degree to which these capacities are related unclear. Moreover, other research has suggested a distinction between attention and VSTM buffers. To explore the degree to which capacity limitations reflect the use of a shared visual processing buffer, we compared individual subject's capacities on attentional and VSTM tasks completed in the same testing session. We used a multiple object tracking (MOT) and a VSTM change detection task, with varying levels of distractors, to measure capacity. Significant correlations in capacity were not observed between the MOT and VSTM tasks when distractor filtering demands differed between the tasks. Instead, significant correlations were seen when the tasks shared spatial filtering demands. Moreover, these filtering demands impacted capacity similarly in both attention and VSTM tasks. These observations fail to support the view that visual attention and VSTM capacity limits result from a shared buffer but instead highlight the role of the resource demands of underlying processes in limiting capacity.