[Effect of 60Co gamma-irradiation on dilute aqueous solutions of surfactants].

Science.gov (United States)

Sawai, T; Shimokowa, T; Miki, Y; Oseko, K; Sawai, T

1978-01-01

Present work deals with the effects of gamma irradiation from 60Co gamma-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with gamma-rays at a room remperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagnometer etc.. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water; a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen.

Electrochemical behavior of Ti and Ti6Al4V in aqueous solutions of citric acid containing halides

Directory of Open Access Journals (Sweden)

Anelise Marlene Schmidt

2006-12-01

Full Text Available This paper reports on an investigation of the electrochemical behavior of Ti grade 2 and Ti6Al4V alloy in aqueous citric acid solutions with pH 2.0 containing halide ions. Voltammetric studies of Ti and the alloy in citric acid, with and without chloride ions, indicate that the Ti and Ti alloy presented a passive behavior in the test solutions used. Pitting was observed at 3.0 and 2.5 V/SCE for Ti and Ti6Al4V, respectively, when bromide ions were added to the solution. In solutions containing fluoride ions, dissolution of the film occurred at potentials close to - 1.0 V/SCE in both electrodes. The iodide ions oxidized on the passive oxide film at potentials close to 1.0 V/SCE. EIS results of the materials in citric acid solutions containing chloride ions revealed that the film's resistance increased as the applied potential rose from 0 to 1.0 V. In bromide-containing solutions, breakdown of the film was confirmed at potentials above 2.0 V/SCE in both electrodes. These results suggest film reformation for Ti and the alloy in solutions containing fluoride at potentials within the passive region.

Radiolysis of pyridoxine (vitamin B{sub 6}) in aqueous solution under different conditions

Energy Technology Data Exchange (ETDEWEB)

Albarran, Guadalupe [Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Mexico 04510, D.F. (Mexico)], E-mail: albarran@nucleares.unam.mx; Ramirez-Cahero, Fernando; Aliev, Roustam [Instituto de Ciencias Nucleares, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Mexico 04510, D.F. (Mexico)

2008-05-15

Aqueous solutions of pyridoxine (1 mM) without or with additive of K{sub 3}[Fe(CN){sub 6}] (2.5 mM) were gamma-irradiated at different doses and dose rate of 2.16 kGy/h in the absence of air, in the presence of air or by their saturation with N{sub 2}O. The radiolytic products were analyzed with HPLC, mass spectrometry and UV spectroscopy. 2,4,5-Trihydroxymethyl-3-pyridinol, pyridoxal, isopyridoxal and 6-hydroxypyridoxine were formed by radiolysis in the absence of K{sub 3}[Fe(CN){sub 6}], and their concentrations were much higher in samples saturated with N{sub 2}O. Pyridoxi-3,6-quinone was found by radiolysis under all the above-mentioned conditions but only in the presence of K{sub 3}[Fe(CN){sub 6}]. Besides, the pyridoxal formation increased in the presence of this oxidizing agent. G values of pyridoxal formation and pyridoxine degradation were quantified. Some details of the radiolytic product formation were discussed.

Effect of 60Co gamma-ray irradiation on dilute aqueous solutions of surfactants

International Nuclear Information System (INIS)

Sawai, Teruko; Shimokawa, Toshinari; Miki, Yasushi; Oseko, Koichi; Sawai, Takeshi

1978-01-01

Present work deals with the effects of gamma irradiation from 60 Co γ-ray source upon aqueous solutions of three kinds of surfactants. When dilute aqueous solutions of sodium dodecyl sulfate (SDS, anionic), cethyl trimethyl ammonium chloride (CTAC, cationic), and polyoxyethylene lauryl ether (POE, non-ionic) were irradiated with γ-rays at a room temperature, the residual concentration, products, surface tension, and forming power were examined by colorimetric method, IR spectrophotometric method, gaschromatography, Ross-Miles method, and Traube's stalagmometer etc. These surfactants were decomposed by the irradiation and thus the surface tension increased and the forming power, on the contrary, decreased with dose. Radiation chemical yields (G-value) of the degradation were about 1 for the solutions of SDS and CTAC, and about 0.3 for the POE solution. From the experimental results, it was found that following chemical reactions seem to occur followed by the radiolysis of water: a) bond cleavage of ester for SDS, of CN for CTAC, and of oxyethylene for POE, b) hydrogen abstraction from the surfactants, c) production of CO bond in the presence of dissolved oxygen. (auth.)

Characterization of stain etched p-type silicon in aqueous HF solutions containing HNO{sub 3} or KMnO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Mogoda, A.S., E-mail: awad_mogoda@hotmail.com [Department of Chemistry, Faculty of Science, Cairo University, Giza (Egypt); Ahmad, Y.H.; Badawy, W.A. [Department of Chemistry, Faculty of Science, Cairo University, Giza (Egypt)

2011-04-15

Research highlights: {yields} Stain etching of p-Si in aqueous HF solutions containing HNO{sub 3} or KMnO{sub 4} was investigated. {yields} The electrical conductivity of the etched Si surfaces was measured using impedance technique. {yields} Scanning electron microscope and energy disperse X-ray were used to analyze the etched surfaces. {yields} Etching in aqueous HF solution containing HNO{sub 3} led to formation of a porous silicon layer. {yields} The formation of the porous silicon layer in HF/KMnO{sub 4} was accompanied by deposition of K{sub 2}SiF{sub 6} on the pores surfaces. - Abstract: Stain etching of p-type silicon in hydrofluoric acid solutions containing nitric acid or potassium permanganate as an oxidizing agent has been examined. The effects of etching time, oxidizing agent and HF concentrations on the electrochemical behavior of etched silicon surfaces have been investigated by electrochemical impedance spectroscopy (EIS). An electrical equivalent circuit was used for fitting the impedance data. The morphology and the chemical composition of the etched Si surface were studied using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) techniques, respectively. A porous silicon layer was formed on Si etched in HF solutions containing HNO{sub 3}, while etching in HF solutions containing KMnO{sub 4} led to the formation of a porous layer and simultaneous deposition of K{sub 2}SiF{sub 6} inside the pores. The thickness of K{sub 2}SiF{sub 6} layer increases with increasing the KMnO{sub 4} concentration and decreases as the concentration of HF increases.

Degradation of adenine in aqueous solution containing 3HHO

International Nuclear Information System (INIS)

Yamamoto, Osamu; Fuji, Izumi

1986-01-01

Aqueous adenine solutions of 5 x 10 -4 M (containing 14 C-adenine and buffered pH 7.0) were irradiated with 60 Co gamma-rays and 3 H beta-rays from tritiated water in the presence of N 2 , O 2 , N 2 O or t-BuOH-N 2 . Thin-layer chromatography (TLC) was carried out bidimensionally for separation of the radiolytically produced products and autoradiography was performed. Considerable differences were observed in the dose-yield curves for the decomposition of adenine and for the product formation between gamma- and beta-radiolyses. As for the degradation yield, oxygen enhancement ratios, 3.19 in gamma-irradiation and 1.08 in beta-irradiation, were obtained at a dose of 3.0 x 10 3 Gy. Similar products were produced both under N 2 and O 2 , but there were found a specific reaction of t-butanol radical with adenine, the high yield of hypoxanthine under N 2 O, and the higher degradation of the TLC origin-fixed products in beta-irradiation. The present results on adenine suggest, as reported previously for thymine, that a specific oxidative species is produced from water in beta-radiolysis but not in gamma-radiolysis. (author)

Removal of radium from aqueous sulphate solutions

International Nuclear Information System (INIS)

Weir, D.R.; Masters, J.T.; Neven, M.

1983-01-01

Radium is often present in ores and an aqueous solution associated with the ore may consequently contain dissolved radium. It is frequently necessary to remove radium from such solutions to reduce the total radium content to a prescribed low level before the solution can be returned to the environment. The present invention is based on the discovery that the total radium content can be reduced to a satisfactory level within a reasonable time by adding a soluble barium salt to a radium-containing sulphate solution which also contains dissolved magnesium at a pH not greater than about 0 to precipitate radium as barium radium sulphate, raising the pH to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate, and separating substantially all of the precipitates from the solution

EXTRACTION OF URANYL NITRATE FROM AQUEOUS SOLUTIONS

Science.gov (United States)

Furman, N.H.; Mundy, R.J.

1957-12-10

An improvement in the process is described for extracting aqueous uranyl nitrate solutions with an organic solvent such as ether. It has been found that the organic phase will extract a larger quantity of uranyl nitrate if the aqueous phase contains in addition to the uranyl nitrate, a quantity of some other soluble nitrate to act as a salting out agent. Mentioned as suitable are the nitrates of lithium, calcium, zinc, bivalent copper, and trivalent iron.

Uranium in aqueous solutions by colorimetry

International Nuclear Information System (INIS)

Anon.

1981-01-01

The method covers the quantitative determination of uranium in known volumes of aqueous solutions that contain radioactive nuclides. These solutions arise from processing of irradiated nuclear fuel and from laboratory studies on irradiated uranium. The method is applicable to solutions containing a minimum of 30 μg of uranium per sample although as little as 0.5 μg can be detected but with lower precision. Highest precision is obtained with 50 to 75 μg of uranium in the test sample. Dilutions must be made at concentrations above 750 μg/ml. The method includes a discussion of photometers and photometric practice, apparatus, reagents, cell matching, preparation of standard curves, calibration by the method of internal standards, procedure, calculation, and precision

Two different one-dimensional structural motifs in [catena-{Cu(tacn)}2Pd(CN)4]Br2.[catena-Cu(tacn)Pd(CN)4]2.H2O (tacn is 1,4,7-triazacyclononane).

Science.gov (United States)

Kuchár, Juraj; Cernák, Juraj

2009-07-01

The title compound, catena-poly[[bis[(triazacyclononane-kappa(3)N,N',N'')copper(II)]-di-mu-cyanido-kappa(4)N:C-palladate(II)-di-mu-cyanido-kappa(4)C:N] dibromide bis[[(triazacyclononane-kappa(3)N,N',N'')copper(II)]-mu-cyanido-kappa(2)N:C-[dicyanidopalladate(II)]-mu-cyanido-kappa(2)C:N] monohydrate], {[Cu(2)Pd(CN)(4)(C(6)H(15)N(3))(2)]Br(2).[Cu(2)Pd(2)(CN)(8)(C(6)H(15)N(3))(2)].H(2)O}(n), (I), was isolated from an aqueous solution containing tacn.3HBr (tacn is 1,4,7-triazacyclononane), Cu(2+) and tetracyanidopalladate(2-) anions. The crystal structure of (I) is essentially ionic and built up of 2,2-electroneutral chains, viz. [Cu(tacn)(NC)-Pd(CN)(2)-(CN)-], positively charged 2,4-ribbons exhibiting the composition {[Cu(tacn)(NC)(2)-Pd(CN)(2)-Cu(tacn)](2n+)}(n), bromide anions and one disordered water molecule of crystallization. The O atom of the water molecule occupies two unique crystallographic positions, one on a centre of symmetry, which is half occupied, and the other in a general position with one-quarter occupancy. One of the tacn ligands also exhibits disorder. The formation of two different types of one-dimensional structural motif within the same structure is a unique feature of this compound.

Production of Plutonium Metal from Aqueous Solutions

Energy Technology Data Exchange (ETDEWEB)

Orth, D.A.

2003-01-16

The primary separation of plutonium from irradiated uranium by the Purex solvent extraction process at the Savannah River Plant produces a dilute plutonium solution containing residual fission products and uranium. A cation exchange process is used for concentration and further decontamination of the plutonium, as the first step in the final preparation of metal. This paper discusses the production of plutonium metal from the aqueous solutions.

DETERMINING PARAMETERS OF THE DIELECTRIC FUNCTION OF A SUBSTANCE IN AQUEOUS SOLUTION BY SELF-REFERENCED REFLECTION THZ SPECTROSCOPY

DEFF Research Database (Denmark)

2008-01-01

Method and apparatus for determining dielectric function of liquid solutions and thereby concentrations of substances in aqueous solution or the volatile/non-volatile nature of the liquid by self-referenced reflection THz spectroscopy. Having the aqueous solution in any container with a window al....... The invention is particularly useful for determining alcohol (ethanol) content in aqueous solution containing other substances and particles....

Aqueous-Containing Precursor Solutions for Efficient Perovskite Solar Cells.

Science.gov (United States)

Liu, Dianyi; Traverse, Christopher J; Chen, Pei; Elinski, Mark; Yang, Chenchen; Wang, Lili; Young, Margaret; Lunt, Richard R

2018-01-01

Perovskite semiconductors have emerged as competitive candidates for photovoltaic applications due to their exceptional optoelectronic properties. However, the impact of moisture instability on perovskite films is still a key challenge for perovskite devices. While substantial effort is focused on preventing moisture interaction during the fabrication process, it is demonstrated that low moisture sensitivity, enhanced crystallization, and high performance can actually be achieved by exposure to high water content (up to 25 vol%) during fabrication with an aqueous-containing perovskite precursor. The perovskite solar cells fabricated by this aqueous method show good reproducibility of high efficiency with average power conversion efficiency (PCE) of 18.7% and champion PCE of 20.1% under solar simulation. This study shows that water-perovskite interactions do not necessarily negatively impact the perovskite film preparation process even at the highest efficiencies and that exposure to high contents of water can actually enable humidity tolerance during fabrication in air.

XPS study of the passive layers formed on lead in aqueous nitrate solutions

International Nuclear Information System (INIS)

Uchida, Miho; Okuwaki, Akitsugu

1997-01-01

The analysis of the lead surface immersed in aqueous nitrate solutions by X-ray photoelectron spectroscopy (XPS) shows the formation of passive oxide layer containing nitrogen compound. The oxide layer formed on the lead surface in aqueous ammonium nitrate solution was hydrolyzed and cracked. (author)

Deacidification of oils and fats of biological origine by aqueous solutions of tertiary amines*

Directory of Open Access Journals (Sweden)

Peter Siegfried

2001-01-01

Full Text Available Deacidification of triacylglycerols by extraction is investigated using aqueous solutions of amines as extractants. Tertiary amines with boiling points ranging between 100° and 170°C, such as 2-methylamino-diethanol, 2-dimethylamino-ethanol, 4-methylmorpholine, 1-dimethylamino-2-propanol etc. were found to be suitable substances. Especially the deacidification by aqueous solutions of 2-dimethylamino-ethanol (DMAE was amply investigated as it is used as an active agent in remedies. Amazingly gelatinous soap stocks are not formed, when the concentration of DMAE exceeds 20% if the free fatty acid content of the oil is below 15%. Two liquid phases are formed in systems composed of triacylglyceroles and aqueous solutions containing 20 to 80% DMAE. Palm oil containing 4.3 wt.% free fatty acids was mixed with an equal amount of an aqueous solution of 30 wt.% DMAE at 60°C. In equilibrium an extract containing 86 wt.% free fatty acids (solvents deducted and a raffinate of 0.09 wt.% free fatty acids are obtained. Loss of neutral oil being 0.7 wt.%.

A reaction-based fluorescent sensor for detection of cyanide in aqueous media

Energy Technology Data Exchange (ETDEWEB)

Wang, Shan-Teng; Sie, Yi-Wun [Department of Chemistry, National Changhua University of Education, Changhua 50058, Taiwan (China); Wan, Chin-Feng [School of Applied Chemistry, Chung Shan Medical University, Taichung City 40201, Taiwan (China); Wu, An-Tai, E-mail: antai@cc.ncue.edu.tw [Department of Chemistry, National Changhua University of Education, Changhua 50058, Taiwan (China)

2016-05-15

A simple boronic acid derivative was utilized as a reaction-based receptor for CN{sup −} in aqueous solution. The receptor showed a selective and sensitive response to CN{sup −} over other various anions via nucleophilic addition of CN{sup −} to the imine moiety of the boronic-based receptor.

Laser-induced photochemical reaction of aqueous maleic acid solutions containing H2O2

International Nuclear Information System (INIS)

Shimizu, Yuichi; Kawanishi, Shunichi; Suzuki, Nobutake

1995-01-01

Hydroxy acid such as glycolic, tartaric and malic acids was directly produced by XeF-laser irradiation of the N 2 -saturated maleic acid aqueous solution containing H 2 O 2 . The selectivities of these products at the maximum of tartaric acid were 71, 4, and 2% at H 2 O 2 feeding rate of 3.2 ml h -1 , respectively. On the other hand, the irradiation of maleates such as dipotassium, calcium, and disodium greatly enhanced the selectivities of tartaric acid formation to 19%, and of malic acid formation to 13%, respectively, for dipotassium maleate. It may be considered from these results that the stability of the hydroxylated intermediate radical plays an important role for the efficient formations of tartaric and malic acids. (author)

Photocatalytic degradation of perfluorooctanoic acid with beta-Ga2O3 in anoxic aqueous solution.

Science.gov (United States)

Zhao, Baoxiu; Lv, Mou; Zhou, Li

2012-01-01

Perfluorooctanoic acid (PFOA) is a new-found hazardous persistent organic pollutant, and it is resistant to decomposition by hydroxyl radical (HO*) due to its stable chemical structure and the high electronegativity of fluorine. Photocatalytic reduction of PFOA with beta-Ga2O3 in anoxic aqueous solution was investigated for the first time, and the results showed that the photoinduced electron (e(cb-)) coming from the beta-Ga2O3 conduction band was the major degradation substance for PFOA, and shorter-chain perfluorinated carboxylic acids (PFCAs, CnF2n+i1COOH, 1 < or = n < or = 6) were the dominant products. Furthermore, the concentration of F- was measured by the IC technique and defluorination efficiency was calculated. After 3 hr, the photocatalytic degradation efficiency was 98.8% and defluorination efficiency was 31.6% in the presence of thiosulfate and bubbling N2. The degradation reaction followed first-order kinetics (k = 0.0239 min(-1), t1/2 = 0.48 hr). PFCAs (CnF2n+1COOH, 1 < or = n < or = 7) were detected and measured by LC-MS and LC-MS/MS methods. It was deduced that the probable photocatalytic degradation mechanism involves e(cb-) attacking the carboxyl of CnF2n+1COOH, resulting in decarboxylation and the generation of CnF2n+1*. The produced CnF2n+1* reacted with H2O, forming CnF2n+1OH, then CnF2n+1OH underwent HF loss and hydrolysis to form CnF2n+1COOH.

The reactivity of the electron formed in the radiolysis of aerated alkaline aqueous solutions containing tetracycline hydrochloride, at 77 Ksup(+)

International Nuclear Information System (INIS)

Guedes, S.M.L.; Vasconcellos, M.B.A.

1986-01-01

The radiolysis of tetracycline hydrochloride dissolved in aerated alkaline aqueous solutions containing 0.1, 0.5 and 1M NaOH at 77 K, followed by ESR is reported. The rate constants for the reactions between the electron and physical or chemical traps which are present in these solutions are calculated. The reactivity of electrons that are formed in the radiolysis of water decreases in the following proportions: physical traps: chemical traps: molecules of water (4.8x10sup(14) : 6.5x10sup(8) : 1.0). The electrons react preferentially with the solute instead of the solvent. (author)

Radiation-induced nitration of organic compounds in aqueous solutions

International Nuclear Information System (INIS)

Ershov, B.G.; Gordeev, A.V.; Bykov, G.L.

2009-01-01

Radiation-induced nitration of organic compounds in aqueous solutions was studied. It was found that γ-irradiation of solutions containing acetic and nitric acid and/or their salts gives nitromethane. Dependences of the product yield on the absorbed dose and the contents of components were established. The mechanism of radiation nitration involving radicals is discussed. (author)

On mechanism of chlorophos radiation-chemical decomposition in aqueous solutions

International Nuclear Information System (INIS)

Danilin, D.I.; Shubin, V.N.

1992-01-01

Quantitative indices of chlorophos decomposition in a aqueous solution and in solutions with a number of additions are studied. Chlorine ions and substances containing the carbonyl group are found among the products of gamma-irradiation of low-concentration chlorophos solutions. The data supporting the running of radiation destructive reactions of reduction nature rather than oxidation type, are presented

Self-Assembly of Discrete Metal Complexes in Aqueous Solution via Block Copolypeptide Amphiphiles

Directory of Open Access Journals (Sweden)

Timothy J. Deming

2013-01-01

Full Text Available The integration of discrete metal complexes has been attracting significant interest due to the potential of these materials for soft metal-metal interactions and supramolecular assembly. Additionally, block copolypeptide amphiphiles have been investigated concerning their capacity for self-assembly into structures such as nanoparticles, nanosheets and nanofibers. In this study, we combined these two concepts by investigating the self-assembly of discrete metal complexes in aqueous solution using block copolypeptides. Normally, discrete metal complexes such as [Au(CN2]−, when molecularly dispersed in water, cannot interact with one another. Our results demonstrated, however, that the addition of block copolypeptide amphiphiles such as K183L19 to [Au(CN2]− solutions induced one-dimensional integration of the discrete metal complex, resulting in photoluminescence originating from multinuclear complexes with metal-metal interactions. Transmission electron microscopy (TEM showed a fibrous nanostructure with lengths and widths of approximately 100 and 20 nm, respectively, which grew to form advanced nanoarchitectures, including those resembling the weave patterns of Waraji (traditional Japanese straw sandals. This concept of combining block copolypeptide amphiphiles with discrete coordination compounds allows the design of flexible and functional supramolecular coordination systems in water.

Application of Activated Carbon for Removal of Arsenic Ions from Aqueous Solutions

Directory of Open Access Journals (Sweden)

R. Ansari

2007-01-01

Full Text Available The activated carbon (AC was used for removal of As(III and As(V ions from aqueous solutions. Sorption experiments were conducted using both batch and column systems. The effect of some important parameters on sorption of these by AC was studied. It was found that among the different factors affecting sorption capacity and efficiency in removal of arsenic from aqueous solutions, the effect of pH and the oxidation state were the most prominent. The optimum pH values for removal of As(III and As(V from aqueous solutions using AC was found 12 and 3 respectively. Impregnation of AC with sulphur contain organic dyes, it is possible to improve As(III uptake considerably.

Solidification of radioactive aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Aikawa, Hideaki; Kato, Kiyoshi; Wadachi, Yoshiki

1970-09-07

A process for solidifying a radioactive waste solution is provided, using as a solidifying agent a mixture of calcined gypsum and burnt vermiculite. The quantity ratio of the mixture is preferred to be 1:1 by volume. The quantity of impregnation is 1/2 of the volume of the total quantity of the solidifying agent. In embodiments, 10 liters of plutonium waste solution was mixed with a mixture of 1:1 calcined gypsum and burnt vermiculite contained in a 20-liter cylindrical steel container lined with asphalt. The plutonium waste solution from the laboratory was neutralized with a caustic soda aqueous solution to prevent explosion due to the nitration of organic compounds. The neutralization is not always necessary. A market available dental gypsum was calcined at 400 to 500/sup 0/C and a vermiculite from Illinois was burnt at 1,100/sup 0/C to prepare the agents. The time required for the impregnation with 10 liters of plutonium solution was four minutes. After impregnation, the temperature rose to 40/sup 0/C within 30 minutes to one hour. Next, it was cooled to room temperature by standing for 3-4 hours. Solidification time was about 1 hour. The Japan Atomic Energy Research Insitute had treated and disposed about 1,000 tons of plutonium waste by this process as of August 19, 1970.

Uranyl fluoride luminescence in acidic aqueous solutions

International Nuclear Information System (INIS)

Beitz, J.V.; Williams, C.W.

1996-01-01

Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 ± 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO 4 at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO 2 F 2 . Studies on the effect of added LiNO 3 or Na 2 WO 4 ·2H 2 O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF 6 content of WF 6 gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF 6

Nitrogen K-edge X-ray absorption near edge structure (XANES) spectra of purine-containing nucleotides in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Shimada, Hiroyuki; Fukao, Taishi; Minami, Hirotake; Ukai, Masatoshi [Department of Applied Physics, Tokyo University of Agriculture and Technology, Koganei-shi, Tokyo 184-8588 (Japan); Fujii, Kentaro; Yokoya, Akinari [Advanced Science Research Center, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki 319-1195 (Japan); Fukuda, Yoshihiro; Saitoh, Yuji [Synchrotron Radiation Research Center, Japan Atomic Energy Agency, Sayo-gun, Hyougo 679-5148 (Japan)

2014-08-07

The N K-edge X-ray absorption near edge structure (XANES) spectra of the purine-containing nucleotide, guanosine 5{sup ′}-monophosphate (GMP), in aqueous solution are measured under various pH conditions. The spectra show characteristic peaks, which originate from resonant excitations of N 1s electrons to π* orbitals inside the guanine moiety of GMP. The relative intensities of these peaks depend on the pH values of the solution. The pH dependence is explained by the core-level shift of N atoms at specific sites caused by protonation and deprotonation. The experimental spectra are compared with theoretical spectra calculated by using density functional theory for GMP and the other purine-containing nucleotides, adenosine 5{sup ′}-monophosphate, and adenosine 5{sup ′}-triphosphate. The N K-edge XANES spectra for all of these nucleotides are classified by the numbers of N atoms with particular chemical bonding characteristics in the purine moiety.

Synthesis, structure and properties of tellurium cubane clusters of niobium and tantalum [M4(μ4-O)(μ3-Te)4(CN)12]6- (M=Nb, Ta)

International Nuclear Information System (INIS)

Fedin, V.P.; Kalinina, I.V.; Virovets, A.V.; Fenske, D.

2001-01-01

A new cubane cluster complex K 6 [Ta 4 (μ 4 -O)(μ 3 -Te) 4 (CN) 12 ] · KOH · 4H 2 O was prepared by high-temperature synthesis from a mixture of TaTe 4 and KCN with subsequent crystallization from aqueous solutions. The compound was characterized by the methods of cyclic voltammetry, X-ray diffraction analysis, IR, Raman and absorption spectroscopies. Comparative study of clusters [M 4 OTe 4 (CN) 12 ] 6- (M=Nb, Ta) containing μ 4 -O-ligands and being the first examples of molecular chalcogenide cubane complexes for group 5 metals of the Periodic System, was made [ru

Thermodynamics of aqueous solutions containing poly (N-isopropylacrylamide)

Energy Technology Data Exchange (ETDEWEB)

Poschlad, K. [Technical University of Berlin, Chair of Thermodynamics TK 7, Strasse des 17, Juni 135, 10623 Berlin (Germany); Enders, S., E-mail: sabine.enders@tu-berlin.d [Technical University of Berlin, Chair of Thermodynamics TK 7, Strasse des 17, Juni 135, 10623 Berlin (Germany)

2011-03-15

Hydrogels undergo reversible and discontinuous volume changes in response to variation of solution conditions such as solvent composition, temperature, salt concentration, and pH. In this contribution we focus our attention on the experimental and theoretical investigation of these swelling equilibria of aqueous cross-linked poly (N-isopropylacrylamide) solutions as well as on the connected demixing behavior of the linear polymer dissolved in water. For the experimental study of the (liquid + liquid) equilibrium an alternative method based on refractive index measurements is suggested. In order to calculate the swelling behavior a model combining an expression for the Gibbs free energy of mixing with an expression for the elastic network is applied. As a model for the Gibbs free energy of mixing the UNIQUAC-approach and the Koningsveld-Kleintjens model are used. For the elastic network contribution again two different theories, namely the phantom network theory and the affine network theory, were applied. Whereas the type of network theory has only a small influence on the calculation results, the Gibbs free energy of mixing has a large impact. Using the UNIQUAC-approach the swelling equilibria can be correlated close to the experimental data, however, this model predicts a homogeneous mixture for linear polymer chains in water. In contrast to this situation the Koningsveld-Kleintjens model does a good job in calculating the swelling equilibria as well as the demixing curve, however, the adjustable parameter must be changed slightly.

Conversion electron Moessbauer study of low carbon steel polarized in aqueous sulfate solution containing sulfite in low concentration

International Nuclear Information System (INIS)

Vertes, Cs.; Lakatos-Varsanyi, M.; Vertes, A.; Kuzmann, E.; Meisel, W.; Guetlich, P.

1992-01-01

The passivation of low carbon steel was studied in aqueous solution of 0.5 M Na 2 SO 4 +0.001 M NaHSO 3 at pH=3.5 and 6.5. The found major components at pH=3.5 were: γ-FeOOH and Fe 3 C, and also FeSO 4 .H 2 O could be identified on the surface of the low carbon steel as a minor component. At pH=6.5, the passive film contained only amorphous iron(III)-oxide or oxyhydroxide. (orig.)

Equilibrium leach tests with cobalt in the system cemented waste form/container material/aqueous solution

International Nuclear Information System (INIS)

Vejmelka, P.; Koester, R.; Lee, M. J.; Han, K. W.

1991-01-01

The equilibrium concentrations of Co in the system of cemented waste form/aqueous solutions were determined including the effect of the container material and its corrosion products under the respective conditions. The chemical conditions in the near field of the waste form were characterized by measurement of the pH and E h value. As disposal relevant solutions, saturated sodium chloride, Q-brine (main constituent MgCl 2 ) and a granitic type groundwater were used. For comparison, also experiments using deionized water were performed. In all systems investigated the cemented waste form itself has a strong influence on the chemical conditions in the near field. The pH and E h values are affected in all cases by the addition of the cemented waste form. There is no or only a slight difference between the E h values if iron powder or iron hydroxide is added to the cemented waste form/solution systems, but the E h is markedly decreased when iron powder is added to the solution free of cement. The Co concentration is decreased in all solutions by the addition of the cemented waste form, the largest effect is observed in Q-brine and this can be attributed either to the sorption of the Co-ions on the corrosion products of the cement or to the coprecipitation of Co-hydroxide and Mg-hydroxide. In the other solutions the Co concentration is decreased by precipitation of Co-hydroxide due to the high pH value of 12.5, and the concentrations are comparable for the different solutions

Enzyme stabilization by glass-derived silicates in glass-exposed aqueous solutions

Science.gov (United States)

Ives, J.A.; Moffett, J.R.; Arun, P.; Lam, D.; Todorov, T.I.; Brothers, A.B.; Anick, D.J.; Centeno, J.; Namboodiri, M.A.A.; Jonas, W.B.

2010-01-01

Objectives: To analyze the solutes leaching from glass containers into aqueous solutions, and to show that these solutes have enzyme activity stabilizing effects in very dilute solutions. Methods: Enzyme assays with acetylcholine esterase were used to analyze serially succussed and diluted (SSD) solutions prepared in glass and plastic containers. Aqueous SSD preparations starting with various solutes, or water alone, were prepared under several conditions, and tested for their solute content and their ability to affect enzyme stability in dilute solution. Results: We confirm that water acts to dissolve constituents from glass vials, and show that the solutes derived from the glass have effects on enzymes in the resultant solutions. Enzyme assays demonstrated that enzyme stability in purified and deionized water was enhanced in SSD solutions that were prepared in glass containers, but not those prepared in plastic. The increased enzyme stability could be mimicked in a dose-dependent manner by the addition of silicates to the purified, deionized water that enzymes were dissolved in. Elemental analyses of SSD water preparations made in glass vials showed that boron, silicon, and sodium were present at micromolar concentrations. Conclusions: These results show that silicates and other solutes are present at micromolar levels in all glass-exposed solutions, whether pharmaceutical or homeopathic in nature. Even though silicates are known to have biological activity at higher concentrations, the silicate concentrations we measured in homeopathic preparations were too low to account for any purported in vivo efficacy, but could potentially influence in vitro biological assays reporting homeopathic effects. ?? 2009 The Faculty of Homeopathy.

Thermodynamic properties of aqueous solutions with citrate ions. Compressibility studies in aqueous solutions of citric acid

International Nuclear Information System (INIS)

Apelblat, Alexander; Korin, Eli; Manzurola, Emanuel

2013-01-01

Highlights: • Over a wide range of concentrations and temperatures sound velocities were measured in aqueous solutions of citric acid. • Compressibility properties of citric acid solutions are thermodynamically characterized. • Changes in the structure of water when citric acid is dissolved are discussed. -- Abstract: Sound velocities in aqueous solutions of citric acid were measured from 15 °C to 50 °C in 5 °C intervals, within the 0.1 mol · kg −1 to 5.0 mol · kg −1 concentration range. These sound velocities served to evaluate the isentropic and isothermal compressibilities, the apparent molar compressibilities, the isochoric thermal pressure coefficients, changes of the cubic expansion coefficients with pressure at constant temperature, the changes of heat capacities with volume and hydration numbers of citric acid in aqueous solutions

Determination of stability constants for thallium(III) cyanide complexes in aqueous solution by means of 13C and 205Ti NMR

International Nuclear Information System (INIS)

Blixt, J.; Gyori, B.; Glaser, J.

1989-01-01

In contrast to what is usually assumed, we have found and proved that thallium(III) forms very strong cyanide complexes in aqueous solution. The authors have investigated this system using 205 Tl, 13 C, and 14 N NMR and potentiometry and established the existence of four thallium(III)-cyanide complexes of the composition Tl(CN) n 3-n , n = 1-4. We have measured their chemical shifts and spin-spin coupling constants and determined their formation constants at 25 degree C in dilute (0.05 M) aqueous solution in the ionic medium ([Na + ] = 1 M, [Li + ] + [H + ] = 3 M, [ClO 4 - ] = 4 M). We have also determined the stability constant for HCN in the same ionic medium, log K a = 10.11 (5)

Diffusion of aqueous solutions of ionic, zwitterionic, and polar solutes

Science.gov (United States)

Teng, Xiaojing; Huang, Qi; Dharmawardhana, Chamila Chathuranga; Ichiye, Toshiko

2018-06-01

The properties of aqueous solutions of ionic, zwitterionic, and polar solutes are of interest to many fields. For instance, one of the many anomalous properties of aqueous solutions is the behavior of water diffusion in different monovalent salt solutions. In addition, solutes can affect the stabilities of macromolecules such as proteins in aqueous solution. Here, the diffusivities of aqueous solutions of sodium chloride, potassium chloride, tri-methylamine oxide (TMAO), urea, and TMAO-urea are examined in molecular dynamics simulations. The decrease in the diffusivity of water with the concentration of simple ions and urea can be described by a simple model in which the water molecules hydrogen bonded to the solutes are considered to diffuse at the same rate as the solutes, while the remainder of the water molecules are considered to be bulk and diffuse at almost the same rate as pure water. On the other hand, the decrease in the diffusivity of water with the concentration of TMAO is apparently affected by a decrease in the diffusion rate of the bulk water molecules in addition to the decrease due to the water molecules hydrogen bonded to TMAO. In other words, TMAO enhances the viscosity of water, while urea barely affects it. Overall, this separation of water molecules into those that are hydrogen bonded to solute and those that are bulk can provide a useful means of understanding the short- and long-range effects of solutes on water.

Origin of supercharging in electrospray ionization of noncovalent complexes from aqueous solution.

Science.gov (United States)

Sterling, Harry J; Williams, Evan R

2009-10-01

The use of m-nitrobenzyl alcohol (m-NBA) to enhance charging of noncovalent complexes formed by electrospray ionization from aqueous solutions was investigated. Addition of up to 1% m-NBA can result in a significant increase in the average charging of complexes, ranging from approximately 13% for the homo-heptamer of NtrC4-RC (317 kDa; maximum charge state increases from 42+ to 44+) to approximately 49% for myoglobin (17.6 kDa; maximum charge state increases from 9+ to 16+). Charge state distributions of larger complexes obtained from heated solutions to which no m-NBA was added are remarkably similar to those containing small amounts of m-NBA. Dissociation of the complexes through identical channels both upon addition of higher concentrations of m-NBA and heating is observed. These results indicate that the enhanced charging upon addition of m-NBA to aqueous electrospray solutions is a result of droplet heating owing to the high boiling point of m-NBA, which results in a change in the higher-order structure and/or dissociation of the complexes. For monomeric proteins and small complexes, the enhancement of charging is lower for heated aqueous solutions than from solutions with m-NBA because rapid folding of proteins from heated solutions that do not contain m-NBA can occur after the electrospray droplet is formed and is evaporatively cooled.

Fluoresence quenching of riboflavin in aqueous solution by methionin and cystein

International Nuclear Information System (INIS)

Droessler, P.; Holzer, W.; Penzkofer, A.; Hegemann, P.

2003-01-01

The fluorescence quantum distributions, fluorescence quantum yields, and fluorescence lifetimes of riboflavin in methanol, DMSO, water, and aqueous solutions of the sulphur atom containing amino acids methionin and cystein have been determined. In methanol, DMSO, and water (pH=4-8) only dynamic fluorescence reduction due to intersystem crossing and internal conversion is observed. In aqueous methionin solutions of pH=5.25-9 a pH independent static and dynamic fluorescence quenching occurs probably due to riboflavin anion-methionin cation pair formation. In aqueous cystein solutions (pH range from 4.15 to 9) the fluorescence quenching increases with rising pH due to cystein thiolate formation. The cystein thiol form present at low pH does not react with neutral riboflavin. Cystein thiolate present at high pH seems to react with neutral riboflavin causing riboflavin deprotonation (anion formation) by cystein thiolate reduction to the cystein thiol form

Radiolytic effect on the chemical state of iodine in aqueous solution

International Nuclear Information System (INIS)

Shiraishi, H.; Kimiya, T.; Ohmae, M.; Ishigure, K.

1988-01-01

The oxidation state of iodine dissolved in an aqueous solution is easily changed in the presence of radiation field. Hence, it is essential to take the radiolytic effect into account when one is to estimate chemical forms of iodine after being released into the containment under an LOCA condition. This paper summarizes results of γ-radiolysis experiments on aqueous solutions containing iodine species, which have been carried out to extend the previously reported study on the same system. Variation in iodine product distribution with time has been examined as before, utilizing a flow system under irradiation. Attention has been paid to the effect of oxygen, to that of an initial oxidation state of iodine, and to the influence of temperature. Some kinetic analysis on the system was also undertaken

Degradation of di-2-ethylhexyl phthalate in aqueous solution by advanced oxidation process

Directory of Open Access Journals (Sweden)

Maryam Zarean

2015-01-01

Conclusion: It could be found that the UV/O3 process is a method for DEHP degradation in aqueous solution and may be recommended as a supplement with other processes for treatment of solutions containing low DEHP concentrations.

Phytodegradation potential of bisphenolA from aqueous solution by Azolla Filiculoides.

Science.gov (United States)

Zazouli, Mohammad Ali; Mahdavi, Yousef; Bazrafshan, Edris; Balarak, Davoud

2014-01-01

Many organic hazardous pollutants such as bisphenolA (BPA) which are toxic and not easily biodegradable can concerns for environmental pollution worldwide. The objective of this study was to examine whether Azolla Filiculoides is able to remove BPA from aqueous solutions. In this study, the Azolla with different biomass (0.3, 0.6, 0.9, 1.2 g) has been cultured in solution that was contained 5, 10, 25 and 50 ppm BPA. Samples were collected every 2 days from all of containers. The analytical determination of BPA was performed by using of DR4000 uv-visible at λmax = 276 nm. The results indicated that Azolla has high ability to remove BPA from aqueous solutions. The BPA removal was 60-90%. The removal efficiency is increasing with decreasing of BPA concentration and increasing of biomass amount and vice versa. The removal efficiency was more than 90% when BPA concentration was 5 ppm and amount of biomass was 0.9gr. It is concluded that Azolla able remove BPA by Phytodegradation from the aqueous solutions. Since conventional methods of BPA removal need to high cost and energy, phytoremediation by Azolla as a natural treatment system can decrease those issues and it can be a useful and beneficial method to removal of BPA.

A portable concentrator for processing plutonium containing solutions

International Nuclear Information System (INIS)

Chamberlain, D.B.; Conner, C.; Chen, L.

1995-01-01

This report describes a horizontal, compact agitated-film concentrator called a Rototherm, manufactured by Artisan Industries, Inc. which can be used to process aqueous solutions of radioactive wastes containing plutonium. The unit is designed to concentrate liquid streams to a high-solid content slurry

Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

International Nuclear Information System (INIS)

Ochsenfeld, W.; Schmieder, H.

1976-01-01

Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

Peroxide coordination of tellurium in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Mikhaylov, Alexey A.; Medvedev, Alexander G. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel); Churakov, Andrei V.; Grishanov, Dmitry A.; Prikhodchenko, Petr V. [Kurnakov Institute of General and Inorganic Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Lev, Ovadia [The Casali Center of Applied Chemistry, The Institute of Chemistry, The Hebrew University of Jerusalem (Israel)

2016-02-15

Tellurium-peroxo complexes in aqueous solutions have never been reported. In this work, ammonium peroxotellurates (NH{sub 4}){sub 4}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2} (1) and (NH{sub 4}){sub 5}Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH).1.28 H{sub 2}O.0.72 H{sub 2}O{sub 2} (2) were isolated from 5 % hydrogen peroxide aqueous solutions of ammonium tellurate and characterized by single-crystal and powder X-ray diffraction analysis, by Raman spectroscopy and thermal analysis. The crystal structure of 1 comprises ammonium cations and a symmetric binuclear peroxotellurate anion [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 4}(OH){sub 2}]{sup 4-}. The structure of 2 consists of an unsymmetrical [Te{sub 2}(μ-OO){sub 2}(μ-O)O{sub 5}(OH)]{sup 5-} anion, ammonium cations, hydrogen peroxide, and water. Peroxotellurate anions in both 1 and 2 contain a binuclear Te{sub 2}(μ-OO){sub 2}(μ-O) fragment with one μ-oxo- and two μ-peroxo bridging groups. {sup 125}Te NMR spectroscopic analysis shows that the peroxo bridged bitellurate anions are the dominant species in solution, with 3-40 %wt H{sub 2}O{sub 2} and for pH values above 9. DFT calculations of the peroxotellurate anion confirm its higher thermodynamic stability compared with those of the oxotellurate analogues. This is the first direct evidence for tellurium-peroxide coordination in any aqueous system and the first report of inorganic tellurium-peroxo complexes. General features common to all reported p-block element peroxides could be discerned by the characterization of aqueous and crystalline peroxotellurates. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Caution on the storage of waters and aqueous solutions in plastic containers for hydrogen and oxygen stable isotope analysis.

Science.gov (United States)

Spangenberg, Jorge E

2012-11-30

The choice of containers for storage of aqueous samples between their collection, transport and water hydrogen ((2)H) and oxygen ((18)O) stable isotope analysis is a topic of concern for a wide range of fields in environmental, geological, biomedical, food, and forensic sciences. The transport and separation of water molecules during water vapor or liquid uptake by sorption or solution and the diffusive transport of water molecules through organic polymer material by permeation or pervaporation may entail an isotopic fractionation. An experiment was conducted to evaluate the extent of such fractionation. Sixteen bottle-like containers of eleven different organic polymers, including low and high density polyethylene (LDPE and HDPE), polypropylene (PP), polycarbonate (PC), polyethylene terephthalate (PET), and perfluoroalkoxy-Teflon (PFA), of different wall thickness and size were completely filled with the same mineral water and stored for 659 days under the same conditions of temperature and humidity. Particular care was exercised to keep the bottles tightly closed and prevent loss of water vapor through the seals. Changes of up to +5‰ for δ(2)H values and +2.0‰ for δ(18)O values were measured for water after more than 1 year of storage within a plastic container, with the magnitude of change depending mainly on the type of organic polymer, wall thickness, and container size. The most important variations were measured for the PET and PC bottles. Waters stored in glass bottles with Polyseal™ cone-lined PP screw caps and thick-walled HDPE or PFA containers with linerless screw caps having an integrally molded inner sealing ring preserved their original δ(2)H and δ(18)O values. The carbon, hydrogen, and oxygen stable isotope compositions of the organic polymeric materials were also determined. The results of this study clearly show that for precise and accurate measurements of the water stable isotope composition in aqueous solutions, rigorous sampling and

Physical Removal of Anions from Aqueous Media by Means of a Macrocycle-Containing Polymeric Network

KAUST Repository

Ji, Xiaofan; Wu, Ren-Tsung; Long, Lingliang; Guo, Chenxing; Khashab, Niveen M.; Huang, Feihe; Sessler, Jonathan L.

2018-01-01

Reported here is a hydrogel-forming polymer network that contains a water-soluble tetracationic macrocycle. Upon immersion of this polymer network in aqueous solutions containing various inorganic and organic salts, changes in the physical

Effect of liquid oil additive on lithium-ion battery ceramic composite separator prepared with an aqueous coating solution

Energy Technology Data Exchange (ETDEWEB)

Kim, Sang Woo [Division of Advanced Materials Engineering, Kongju National University, 1223–24, Cheonan-daero, Cheonan, Chungnam, 31080 (Korea, Republic of); Ryou, Myung-Hyun [Department of Chemical & Biological Engineering, Hanbat National University, 125, Dongseodaero, Yuseong-gu, Daejeon, 34158 (Korea, Republic of); Lee, Yong Min, E-mail: yongmin.lee@hanbat.ac.kr [Department of Chemical & Biological Engineering, Hanbat National University, 125, Dongseodaero, Yuseong-gu, Daejeon, 34158 (Korea, Republic of); Cho, Kuk Young, E-mail: kycho@hanyang.ac.kr [Department of Materials Science and Chemical Engineering, Hanyang University, 55, Hanyangdaehak-ro, Sangrok-gu, Ansan, Gyeonggi-do, 15588 (Korea, Republic of)

2016-08-05

Ceramic composite separators (CCSs) play a critical role in ensuring safety for lithium-ion batteries (LIBs), especially for mid- and large-sized devices. However, production of CCSs using organic solvents has some cost and environmental concerns. An aqueous process for fabricating CCSs is attractive because of its cost-effectiveness and environmental-friendliness because organic solvents are not used. The success of an aqueous coating system for LIBs is dependent upon minimizing moisture content, as moisture has a negatively impact on LIB performance. In this study, CCSs were fabricated using an aqueous coating solution containing Al{sub 2}O{sub 3} and an acrylic binder. Compared with polyethylene (PE) separators, CCSs coated with an aqueous coating solution showed improved thermal stability, electrolyte uptake, puncture strength, ionic conductivity, and rate capability. In addition, our new approach of introducing a small amount of an oily liquid to the aqueous coating solution reduced the water adsorption by 11.7% compared with coatings that do not contain the oily liquid additive. - Highlights: • Ceramic composite separator is fabricated using aqueous coating process. • Coated separator showed enhanced mechanical and thermal stability. • Liquid oil additive in coating solution reduce moisture reabsorption of separator. • Oil additive in aqueous coating solution does not deteriorate LIB performance.

Radiation chemistry of aqueous solutions of hydrazine at elevated temperatures: Pt. 2. Solutions containing oxygen

International Nuclear Information System (INIS)

Buxton, G.V.; Stuart, C.R.

1997-01-01

Here, we investigate the effects of oxygen on the radiation chemistry of hydrazine at elevated temperatures. The chemistry of this system is important to reactor coolant chemistry, particularly under start-up conditions when hydrazine is added to suppress corrosion which would otherwise be caused by the ingress of oxygen. The radiation chemistry of aqueous solutions of hydrazine has been investigated previously in the presence of oxygen by Ershov et al., but only at room temperature. In those experiments, both steady-state γ-radiolysis and pulse radiolysis were used to deduce the mechanism of decomposition of hydrazine in the presence of oxygen. (author)

Efficient adsorption of Au(CN)2- from gold cyanidation with graphene oxide-polyethylenimine hydrogel as adsorbent

Science.gov (United States)

Yang, Lang; Jia, Feifei; Yang, Bingqiao; Song, Shaoxian

The adsorption of gold cyanide complex ion (Au(CN)2-) on graphene oxide-polyethylenimine hydrogel (GO/PEI hydrogel) from gold cyanidation has been studied to explore the possibility of the application of GO/PEI hydrogel in gold cyanidation process for extracting gold from ores. The adsorption was carried out in artificial Au(CN)2- aqueous solution with GO/PEI hydrogel as adsorbent. The experimental results, as well as IR, XPS and SEM-EDS, have shown that GO/PEI hydrogel exhibited a high adsorption capacity and a fast adsorption rate of Au(CN)2-, suggesting that GO/PEI hydrogel might be a good adsorbent for the recovery of Au(CN)2-. The adsorption of Au(CN)2- on GO/PEI hydrogel obeyed the Langmuir isotherm model and fitted well with the pseudo second order model. The good recovery of Au(CN)2- was largely related to the porous structure, large specific surface area, as well as the oxygenous functional groups on the surface of GO/PEI hydrogel.

Interaction between lactose and cadmium chloride in aqueous solutions as seen by diffusion coefficients measurements

International Nuclear Information System (INIS)

Verissimo, Luis M.P.; Gomes, Joselaine C.S.; Romero, Carmen; Esteso, Miguel A.; Sobral, Abilio J.F.N.; Ribeiro, Ana C.F.

2013-01-01

Highlights: ► Diffusion coefficients of aqueous systems containing lactose and cadmium chloride. ► Influence of the lactose on the diffusion of cadmium chloride. ► Interactions between Cd 2+ and lactose. -- Abstract: Diffusion coefficients of an aqueous system containing cadmium chloride 0.100 mol · dm −3 and lactose at different concentrations at 25 °C have been measured, using a conductimetric cell and an automatic apparatus to follow diffusion. The cell relies on an open-ended capillary method and a conductimetric technique is used to follow the diffusion process by measuring the resistance of a solution inside the capillaries, at recorded times. From these results and by ab initio calculations, it was possible to obtain a better understanding of the effect of lactose on transport of cadmium chloride in aqueous solutions

Efficient removal of Co(II) from aqueous solution by titanate sodium nanotubes

Institute of Scientific and Technical Information of China (English)

Dong-Mei Li; Ning Liu; Fei-Ze Li; Jia-Li Liao; Ji-Jun Yang; Bing Li; Yun-Ming Chen; Yuan-You Yang; Jin-Song Zhang; Jun Tang

2016-01-01

In this paper, a novel material for Co(II) adsorption, titanate sodium nanotubes (Na2Ti2O5-NTs) were synthesized and characterized, and then they were used to remove Co(II) from aqueous solution and compared with titanic acid nanotubes (H2Ti2O5-NTs) and potassium hexatitanate whiskers (K2Ti6O13). The results showed that the adsorption of Co(II) on the materials was dependent on pH values and was a spontaneous, endothermic process. Specifically, Na2Ti2O5-NTs exhibited much more efficient ability to adsorb Co(II) from aqueous solution, with the maximum adsorption capacity of 85.25 mg/g. Furthermore, Na2Ti2O5-NTs could selectively adsorb Co(II) from aque-ous solution containing coexisting ions (Na+, K+, Mg2+, and Ca2+). The results suggested that Na2Ti2O5-NTs were potential effective adsorbents for removal of Co(II) or cobalt-60 from wastewater.

Synthesis of 5'-CMP and 5'-dCMP in aqueous solution induced by low energy ions implantation

International Nuclear Information System (INIS)

Shi Huaibin; Shao Chunlin; Wang Xiangqin; Yu Zengliang

2001-01-01

Low energy N + ions produced by N 2 are accelerated and then introduced into aqueous solution to induce chemical reactions. This process avoids the need of a vacuum chamber and makes it possible to investigate the actions of low energy ions in aqueous solution. In order to explore prebiotic synthesis of nucleotide via reaction between low energy ions and aqueous solution under the primitive earth conditions, low energy N + is implanted into aqueous solution containing cytosine, D-ribose, D-2-deoxyribose and NH 4 H 2 PO 4 . It is confirmed that 5'-CMP and 5'-dCMP are produced by HPLC and 1 H-NMR analyses. The relation between yields of 5'-CMP and 5'-dCMP and irradiation time has been obtained

Mutual diffusion of sodium hyaluranate in aqueous solutions

International Nuclear Information System (INIS)

Veríssimo, Luís M.P.; Valada, Teresa I.C.; Sobral, Abilio J.F.N.; Azevedo, Eduarda E.F.G.; Azevedo, Maria L.G.; Ribeiro, Ana C.F.

2014-01-01

Highlights: • Binary diffusion coefficients for the systems containing sodium hyaluronate. • Influence of the aggregation on diffusion of the sodium hyaluronate in the aqueous media. • Estimation of the thermodynamic and mobility factors from mutual diffusion. -- Abstract: The Taylor dispersion technique has been used for measuring mutual diffusion coefficients of sodium hyaluronate in aqueous solutions at T = 298.15 K, and concentrations ranging from (0.00 to 0.50) g · dm −3 . The results are interpreted on the basis of Nernst, and Onsager and Fuoss theoretical equations. From the diffusion coefficient at infinitesimal concentration, the limiting ionic conductivity and the tracer diffusion coefficient of hyaluronate ion were estimated. These studies have been complemented by molecular mechanics calculations

Some aspects of the formation of the dispersed phase in aqueous solutions

International Nuclear Information System (INIS)

Ershov, B.G.; Sukhov, N.L.; Troitskii, D.I.

1992-01-01

The experimental results on the formation of silver colloids and some insoluble salts in aqueous solutions are discussed. Colloidal silver particles are formed as a result of radiation-chemical reduction of Ag + ions in deaerated solution containing alcohols or formic acid. Subcolloidal species containing 12-16 atoms are the precursors of the metal sol. The rate of nucleation increases with increasing concentration of indifferent electrolyte (NaClO 4 ) in solution as a result of the change in the ionic strength. Some anions such as sulphate, formate and others are chemisorbed on the subcolloidal silver surfaces, which dramatically decreases their stability. (author)

Physical Removal of Anions from Aqueous Media by Means of a Macrocycle-Containing Polymeric Network

KAUST Repository

Ji, Xiaofan

2018-02-13

Reported here is a hydrogel-forming polymer network that contains a water-soluble tetracationic macrocycle. Upon immersion of this polymer network in aqueous solutions containing various inorganic and organic salts, changes in the physical properties are observed that are consistent with absorption of the constituent anions into the polymer network. This absorption is ascribed to host-guest interactions involving the tetracationic macrocyclic receptor. Removal of the anions may then be achieved by lifting the resulting hydrogels out of the aqueous phase. Treating the anion-containing hydrogels with dilute HCl leads to the protonation-induced release of the bound anions. This allows the hydrogels to be recycled for reuse. The present polymer network thus provides a potentially attractive approach to removing undesired anions from aqueous environments.

Oxygen effect in the radiolysis of triton X-100 aqueous solution

International Nuclear Information System (INIS)

Perkowski, J.; Mayer, J.

1994-01-01

Experiments with Triton X-100 as a model surfactant were performed under steady-state conditions, using deoxygenated solutions as well as those saturated with N 2 O, O 2 or N 2 O/O 2 mixtures. The Triton x-100 decomposition yield was dependent on the O 2 content of the irradiated system. Oxygen promoted surfactant decomposition in aqueous solution containing only Triton X-100. (author) 13 refs.; 1 tab

The immiscible aqueous solutions of alkyl phosphates. Study for the purpose of uranium extraction from phosphoric acid solutions

International Nuclear Information System (INIS)

Mauborgne, Bernard

1979-01-01

Systems of immiscible aqueous solutions composed by a phase rich in mineral salt and by another phase almost totally containing an organic salt, have been studied for years, with quaternary ammonium salts with an organic cation. The objective of this research is to study systems symmetric to the previous ones, i.e. with organic anions such as alkyl phosphates, and then to try to understand mechanisms of extraction of metals in these environments. Based on properties of immiscible aqueous solutions, an original three-phase process of liquid-liquid extraction has been developed, and is used to separate uranium in phosphoric acids with better performance than the existing industrial processes [fr

Forced Spreading of Aqueous Solutions on Zwitterionic Sulfobetaine Surfaces for Rapid Evaporation and Solute Separation.

Science.gov (United States)

Wu, Cyuan-Jhang; Singh, Vickramjeet; Sheng, Yu-Jane; Tsao, Heng-Kwong

2017-08-01

Solute separation of aqueous mixtures is mainly dominated by water vaporization. The evaporation rate of an aqueous drop grows with increasing the liquid-gas interfacial area. The spontaneous spreading behavior of a water droplet on a total wetting surface provides huge liquid-gas interfacial area per unit volume; however, it is halted by the self-pinning phenomenon upon addition of nonvolatile solutes. In this work, it is shown that the solute-induced self-pinning can be overcome by gravity, leading to anisotropic spreading much faster than isotropic spreading. The evaporation rate of anisotropic spreading on a zwitterionic sulfobetaine surface is 25 times larger as that on a poly(methyl methacrylate) surface. Dramatic enhancement of evaporation is demonstrated by simultaneous formation of fog atop liquid film. During anisotropic spreading, the solutes are quickly precipitated out within 30 s, showing the rapid solute-water separation. After repeated spreading process for the dye-containing solution, the mean concentration of the collection is doubled, revealing the concentration efficiency as high as 100%. Gravity-enhanced spreading on total wetting surfaces at room temperature is easy to scale-up with less energy consumption, and thus it has great potentials for the applications of solute separation and concentration.

Formation and stabilization of anionic metal complexes in concentrated aqueous quaternary ammonium salt solutions

International Nuclear Information System (INIS)

Aronson, F.L.; Hwang, L.L.Y.; Ronca, N.; Solomon, N.A.; Steigman, J.

1985-01-01

Anionic complexes of transition metals were stabilized in aqueous solutions containing high concentrations of various short-chain quaternary ammonium salts. Compounds with longer paraffin chains were effective in much less concentrated solution. Complex ions were detected spectrophotometrically. FeCl 4 - , which is usually formed in concentrated HCl, was the predominant Fe(III) complex in 30 m choline chloride containing only 0.12 M HCl. A yellow transitory Tc(VII) chloro-addition intermediate, formed in the reduction of TcO 4 - by concentrated HCl, was stabilized when the solution also contained 25 m choline chloride. Its spectrum, as well as the isolation of an already known Tc(VII) bipyridyl complex, is reported. Concentrated organic electrolytes also stabilized Tc(V) oxide halides against disproportionation and Tc(IV) hexahalides against hydrolysis. Halochromates of Cr(VI) were formed and stabilized in dilute acid containing quaternary ammonium salts. Their UV spectra showed the well-resolved vibronic fine structure associated with the symmetric chromium-to-oxygen charge-transfer band. It is known that these progressions are resolved in aprotic solvents, but not in aqueous acidic solution alone, and that the loss of fine structure in aqueous media is due to hydrogen bonding. The stabilization of anionic metal complexes and the resolution of vibronic structure in halochromates are probably consequences of water-structure-enforced ion paring. The present work suggests that the water molecules in immediate contact with the complex anions are more strongly hydrogen bonded to each other than to the complex. 21 references, 4 figures

Pulse radiolysis studies of iron(I) in aqueous solutions

International Nuclear Information System (INIS)

Nenadovic, M.T.; Micic, O.I.; Muk, A.A.

1980-01-01

The absorption spectrum and decay kinetics of the products of the reactions of iron(II) ions with hydrated electrons and hydrogen atoms have been studied in aqueous solution using pulse-radiolysis techniques. Iron(I) is formed by reaction with hydrated electrons and its absorption spectrum is reported and discussed. The formation of molecular hydrogen by reaction of Fe + with water is suppressed by other solutes present in the solutions. In acidic solutions containing [SO 4 ] 2- , the intermediates formed in the reaction with H atoms decay by a first-order process and produce molecular hydrogen, but the rate of their decay does not depend only on the oxonium ion concentration but also on intermolecular rearrangement in the [FeSO 4 -H] complex. (author)

Corrosion behaviour of Alloy 800 in high temperature aqueous solutions: Electrochemical studies

International Nuclear Information System (INIS)

Olmedo, A.M.; Villegas, M.; Alvarez, M.G.

1996-01-01

The anodic behaviour and passivity breakdown of Alloy 800 in aqueous solutions of sodium chloride, sodium sulphate and sodium bicarbonate were studied by electrochemical techniques in the temperature range from 60 C to 280 C. The pitting resistance and pitting morphology of the alloy in chloride plus sulphate and chloride plus bicarbonate mixtures, at 60 C and 280 C, were also examined. Increasing bicarbonate or sulphate additions to chloride solutions shift the characteristic pitting potential of Alloy 800 to higher values, both at low and high temperatures. Changes in pitting morphology were observed in sulphate containing solutions while the morphology of the attack found in bicarbonate containing solutions was similar to that in pure chloride solutions. Finally, no localized or substantial generalized corrosion was detected in pure sulphate or bicarbonate solutions at any temperature. (orig.)

Electrogenerated chemiluminescence induced by sequential hot electron and hole injection into aqueous electrolyte solution

Energy Technology Data Exchange (ETDEWEB)

Salminen, Kalle; Kuosmanen, Päivi; Pusa, Matti [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland); Kulmala, Oskari [University of Helsinki, Department of Physics, P.O. Box 64, FI-00014 (Finland); Håkansson, Markus [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland); Kulmala, Sakari, E-mail: sakari.kulmala@aalto.fi [Aalto University, Department of Chemistry, Laboratory of Analytical Chemistry, P.O. Box 16100, FI-00076 Aalto (Finland)

2016-03-17

Hole injection into aqueous electrolyte solution is proposed to occur when oxide-coated aluminum electrode is anodically pulse-polarized by a voltage pulse train containing sufficiently high-voltage anodic pulses. The effects of anodic pulses are studied by using an aromatic Tb(III) chelate as a probe known to produce intensive hot electron-induced electrochemiluminescence (HECL) with plain cathodic pulses and preoxidized electrodes. The presently studied system allows injection of hot electrons and holes successively into aqueous electrolyte solutions and can be utilized in detecting electrochemiluminescent labels in fully aqueous solutions, and actually, the system is suggested to be quite close to a pulse radiolysis system providing hydrated electrons and hydroxyl radicals as the primary radicals in aqueous solution without the problems and hazards of ionizing radiation. The analytical power of the present excitation waveforms are that they allow detection of electrochemiluminescent labels at very low detection limits in bioaffinity assays such as in immunoassays or DNA probe assays. The two important properties of the present waveforms are: (i) they provide in situ oxidation of the electrode surface resulting in the desired oxide film thickness and (ii) they can provide one-electron oxidants for the system by hole injection either via F- and F{sup +}-center band of the oxide or by direct hole injection to valence band of water at highly anodic pulse amplitudes. - Highlights: • Hot electrons injected into aqueous electrolyte solution. • Generation of hydrated electrons. • Hole injection into aqueous electrolyte solution. • Generation of hydroxyl radicals.

Oxidation of substituted alkyl radicals by IrCl62-, Fe(CN)63-, and MnO4- in aqueous solution. Electron transfer versus chlorine transfer from IrCl62-

International Nuclear Information System (INIS)

Steenken, S.; Neta, P.

1982-01-01

Alkyl radicals substituted at C/sub α/ by alkyl, carboxyl, hydroxyl, alkoxyl, and chlorine react in aqueous solutions with Ir/sup IV/Cl 6 2- to yield Ir(III) species. In the case of substitution by hydroxyl and alkoxyl, the rate constants are in the diffusion-controlled range ((4-6) x 10 9 M -1 s -1 ) and the reaction proceeds by electron transfer. In the case of ethyl, methyl, carboxymethyl, and chloromethyl radicals the rate constants range from 3.1 x 10 9 for ethyl to 2.8 x 10 7 M -1 s -1 for trichloromethyl and the reaction proceeds by chlorine transfer from IrCl 6 2- to the alkyl radical. With isopropyl and tert-butyll radicals the reaction proceeds by both electron and chlorine transfer. Alkyl radicals also react with Fe(CN) 6 3- . The rate constants increase strongly with increasing alkylation at C/sub α/ from 5 x 10 6 for methyl to 3.6 x 10 9 M -1 s -1 for tert-butyl, indicating that the transition state for the reaction is highly polar. Rate constants for reaction of MnO 4 - with alkyl radicals are of the order 10 9 M -1 s -1 . 4 figures, 1 table

Metastable equilibrium for the quaternary system containing with lithium+potassium+magnesium+chloride in aqueous solution at 323K

Energy Technology Data Exchange (ETDEWEB)

Yu, Xudong; Yin, Qinghong; Jiang, Dongbo; Zeng, Ying [Chengdu University of Technology, Chengdu (China)

2014-06-15

The metastable equilibrium of the system contained with lithium, potassium, magnesium, and chloride in aqueous system was investigated at 323 K using an isothermal evaporation method. The isothermal experimental data and physicochemical properties, such as density and refractive index of the equilibrated solution, were determined. With the experimental results, the stereo phase diagram, the projected phase diagram, the water content diagram and the physicochemical properties versus composition diagrams were constructed. The projected phase diagram consists of three invariant points, seven univariant curves and five crystallization fields corresponding to single salts potassium chloride (KCl), lithium chloride monohydrate (LiCl·H{sub 2}O), bischofite (MgCl{sub 2}·6H{sub 2}O) and two double salts lithium carnallite (LiCl·MgCl{sub 2}·7H{sub 2}O) and potassium carnallite (KCl·MgCl{sub 2}·6H{sub 2}O). Salt KCl has the largest crystallization region; it contains almost 95% of the general crystallization field.

21 CFR 524.1200b - Kanamycin ophthalmic aqueous solution.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Kanamycin ophthalmic aqueous solution. 524.1200b... (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS OPHTHALMIC AND TOPICAL DOSAGE FORM NEW ANIMAL DRUGS § 524.1200b Kanamycin ophthalmic aqueous solution. (a) Specifications. The drug, which is in an aqueous...

Formation and disappearance of superoxide radicals in aqueous solutions

International Nuclear Information System (INIS)

Allen, A.O.; Bielski, B.H.J.

1980-01-01

A literature review of superoxide radicals in aqueous solutions is presented covering the following: history; methods of formation of aqueous HO 2 /HO 2 - by radiolysis and photolysis, electrolysis, mixing nonaqueous solutions into water, chemical reactions, enzymatic generation of O 2 - , and photosensitization; and properties of HO 2 /O 2 - in aqueous solution, which cover spontaneous dismutation rates, pk and absorption spectra, catalyzed dismutation, thermodynamics and the so-called Haber-Weiss Reaction

Preliminary study on lithium-salt aqueous solution blanket

International Nuclear Information System (INIS)

Yoshida, Hiroshi; Naruse, Yuji; Yamaoka, Mitsuaki; Ohara, Atsushi; Ono, Kiyoshi; Kobayashi, Shigetada.

1992-06-01

Aqueous solution blanket using lithium salts such as LiNO 3 and LiOH have been studied in the US-TIBER program and ITER conceptual design activity. In the JAERI/LANL collaboration program for the joint operation of TSTA (Tritium Systems Test Assembly), preliminary design work of blanket tritium system for lithium ceramic blanket, aqueous solution blanket and liquid metal blanket, have been performed to investigate technical feasibility of tritium demonstration tests using the TSTA. Detail study of the aqueous solution blanket concept have not been performed in the Japanese fusion program, so that this study was carried out to investigate features of its concept and to evaluated its technical problems. The following are the major items studied in the present work: (i) Neutronics of tritium breeding ratio and shielding performance Lithium concentration, Li-60 enrichment, beryllium or lead, composition of structural material/beryllium/solution, heavy water, different lithium-salts (ii) Physicochemical properties of salts Solubility, corrosion characteristics and compatibility with structural materials, radiolysis (iii) Estimation of radiolysis in ITER aqueous solution blanket. (author)

Electrochemical Study of Modified Glassy Carbon Electrode with Carboxyphenyl Diazonium Salt in Aqueous Solutions

Directory of Open Access Journals (Sweden)

Mariem BOUROUROU

2014-05-01

Full Text Available The covalent grafting of carboxyphenyl functionalities to planar carbon substrates by reaction with 2-carboxybenezenediazonium salt has been studied in aqueous acid solution. The surface was characterized, before and after the functionnalization process, by cyclic voltammetry, electrochemical impedance spectroscopy and linear sweep voltammetry (LSV in order to control and to prove the formation of a coating on the carbon surface. The results indicate the presence of substituted phenyl groups on the investigated surface. Electrochemical impedance measurements show that the slowing down of the electron transfer kinetics was more evident by increasing the number of cycles resulting to higher DEp and RCT parameters. Besides, the effect of the pH on the electron transfer processes of the Fe(CN63-/4- at the modified electrode is studied. By changing the solution pH the terminal group’s charge state would vary, based on which the surface pKa value is estimated.

Purification process for aqueous solutions of rare earths by liquid-liquid extraction

International Nuclear Information System (INIS)

Rollat, A.; Sabot, J.L.; Burgard, M.; Delloye, T.

1986-01-01

Alkaline earth metals are removed by liquid-liquid extraction between on aqueous nitric phase of impure rare earth compounds and an organic phase of polyether (crown ether). This process is particularly suited to removal of Ca, Ba and Ra contained in nitric solutions of rare earths [fr

Investigating self-assembly and metal nanoclusters in aqueous di-block copolymers solutions

CERN Document Server

Lo Celso, F; Triolo, R; Triolo, A; Strunz, P; Bronstein, L; Zwanziger, J; Lin, J S

2002-01-01

Self-assembling properties of di-block copolymers/ surfactant hybrids in aqueous solution can be exploited to obtain metal nanoparticles stable dispersion. Results will be presented here for polystyrene-block-poly(ethylene oxide) solutions. A SANS structural investigation has been performed over different molecular weights of both hydrophilic and hydrophobic block, by varying temperature and concentration of the copolymer. A SAXS characterization of micellar systems containing Pt nanoparticles is reported. (orig.)

Aqueous polyethylene oxide solutions

International Nuclear Information System (INIS)

Breen, J.

1987-01-01

A number of aspects concerning the reorientation of polymer, water and ion hydration complexes have been studied in aqueous solution of polyethylene oxide (PEO). The polymer dynamics are investigated by 1 H-PEO and 13 C-PEO nuclear relaxation experiments. 162 refs.; 30 figs.; 19 tabs

Correlation and prediction of osmotic coefficient and water activity of aqueous electrolyte solutions by a two-ionic parameter model

International Nuclear Information System (INIS)

Pazuki, G.R.

2005-01-01

In this study, osmotic coefficients and water activities in aqueous solutions have been modeled using a new approach based on the Pitzer model. This model contains two physically significant ionic parameters regarding ionic solvation and the closest distance of approach between ions in a solution. The proposed model was evaluated by estimating the osmotic coefficients of nine electrolytes in aqueous solutions. The obtained results showed that the model is suitable for predicting the osmotic coefficients in aqueous electrolyte solutions. Using adjustable parameters, which have been calculated from regression between the experimental osmotic coefficient and the results of this model, the water activity coefficients of aqueous solutions were calculated. The average absolute relative deviations of the osmotic coefficients between the experimental data and the calculated results were in agreement

Diffusion coefficients of paracetamol in aqueous solutions

International Nuclear Information System (INIS)

Ribeiro, Ana C.F.; Barros, Marisa C.F.; Veríssimo, Luís M.P.; Santos, Cecilia I.A.V.; Cabral, Ana M.T.D.P.V.; Gaspar, Gualter D.; Esteso, Miguel A.

2012-01-01

Highlights: ► Mutual diffusion coefficients of paracetamol in aqueous dilute solutions. ► Influence of the thermodynamic factors on the variation of their mutual diffusion coefficients. ► Estimation of the mutual limiting diffusion coefficients of the molecular, D m 0 , and ionized forms, D ± 0 , of this drug. - Abstract: Binary mutual diffusion coefficients measured by the Taylor dispersion method, for aqueous solutions of paracetamol (PA) at concentrations from (0.001 to 0.050) mol·dm −3 at T = 298.15 K, are reported. From the Nernst–Hartley equation and our experimental results, the limiting diffusion coefficient of this drug and its thermodynamic factors are estimated, thereby contributing in this way to a better understanding of the structure of such systems and of their thermodynamic behaviour in aqueous solution at different concentrations.

A highly sensitive fluorescent probe based on BODIPY for Hg2+ in aqueous solution

Directory of Open Access Journals (Sweden)

ZHAO Junwei

2016-12-01

Full Text Available A highly sensitive fluorescent probe based on BODIPY and hydrazine for Hg2+ was designed and synthesized.This probe could detect mercury ions in aqueous solutions within 5 min.With the increase of Hg2+ mole concentration,an obvious red shift of UV-Vis absorption wavelength was observed and the fluorescence intensity significantly enhanced.It was found that the fluorescence intensity of an aqueous solution containing 0.1 μmol/L Hg2+ is much stronger than that of blank solution,which indicats that the fluorescent probe has high sensitivity.In addition,other metal ions could not cause the change of fluorescent spectra,which means this probe has good selectivity,as well.

Thermodynamic behavior of erythritol in aqueous solutions and in gelatine gels and its quantification

International Nuclear Information System (INIS)

Tyapkova, Oxana; Bader-Mittermaier, Stephanie; Schweiggert-Weisz, Ute

2013-01-01

Highlights: • Differential scanning calorimetry as a method to determine erythritol crystallization. • Determination of crystallization using solution enthalpy. • Erythritol crystallization influenced by area of air–water-interfaces. • DSC method is applicable for both aqueous solutions and gels. • Adaption of DSC method to other, more complex food matrices is possible. - Abstract: As crystallization of erythritol can cause a sandy mouth-feel in sugar-free products, strategies to avoid crystallization or adaption of food formulation should be elucidated. However, until now erythritol crystallization was only quantified in aqueous solutions, but not in model food systems. Differential scanning calorimetry (DSC) is a simple method for the quantification of phase transition in various systems. However, no methods for the quantification of crystallization from aqueous systems based on DSC have been published until now. In the present study DSC was found to be suitable for the quantification of crystallization using supersaturated aqueous solutions of erythritol and erythritol containing gelatine gels for the first time. The developed method was validated by comparing the crystallization values determined by gravimetric measurement of erythritol crystals and the values obtained by DSC. No significant differences (p < 0.05) have been obtained between the results of the two methods if an appropriate design of measurements was applied. Additionally, the method was adapted to gelatine gels to elucidate the transferability to model food systems. Hence, the method is suitable for quantification of the amount of erythritol crystals present in aqueous solutions and gels, respectively

Fluorescence of aqueous solutions of commercial humic products

Science.gov (United States)

Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

2012-01-01

We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

Radiolysis of human gastric glycopolypeptides in aqueous solution

International Nuclear Information System (INIS)

Nagrani, S.; Bisby, R.H.

1986-01-01

The degradation of human gastric glycopolypeptides by hydroxyl radicals formed in irradiated N 2 0-saturated aqueous solution has been investigated. Gel exclusion chromatography shows the formation of lower molecular weight degradation products after irradiation and the appearance of unsaturated carbonyl-containing products which absorb in the ultra-violet. The radiation-induced destruction of individual monosaccharides in three human glycopolypeptides having different oligosaccharide chains has been measured. The results indicate that the structure of the oligosaccharide chain determines the extent of destruction of each type of monosaccharide present. (author)

Hydrogen production by sodium borohydride in NaOH aqueous solution

Science.gov (United States)

Wang, Q.; Zhang, L. F.; Zhao, Z. G.

2018-01-01

The kinetics of hydrolysis reaction of NaBH4 in NaOH aqueous solution is studied. The influence of pH of the NaOH aqueous solution on the rate of hydrogen production and the hydrogen production efficiency are studied for the hydrolysis reaction of NaBH4. The results show that the activation energy of hydrolysis reaction of NaBH4 increased with the increase of the initial pH of NaOH aqueous solution.With the increasing of the initial pH of NaOH aqueous solution, the rate of hydrogen production and hydrogen production efficiency of NaBH4 hydrolysis decrease.

Knudsen thermogravimetry approach to the thermodynamics of aqueous solutions

International Nuclear Information System (INIS)

Schiraldi, Alberto; Signorelli, Marco; Fessas, Dimitrios

2013-01-01

Highlights: ► Knudsen cells were designed to replace standard TG pans for desorption experiments. ► The Knudsen effusion data allow determination of water activity of aqueous solutions. ► This methods can replace the traditional isopiestic approach for aqueous solutions. ► The Gibbs–Duhem relationship was used to fit the experimental data. -- Abstract: The use of isothermal TGA with Knudsen-like cells allows determination of the thermodynamic activity of water, a W . The typical experiment implies a slow dehydration of the aqueous solution at constant temperature in dynamic vacuum conditions. The method is alternative to the classical isopiestic approach and offers the advantage of a continuous record on increasing the solute concentration. These data can be directly treated according to the classical thermodynamic relationships drawn from the Gibbs–Duhem expression to evaluate the activity and osmotic coefficient of the aqueous solutions of electrolytes and non-electrolytes, and, in the case of electrolytes, allow determination of solubility of the solute. Discrepancies with respect to the literature data are observed when the viscosity of the systems becomes too high, as in the case of sugars with a very large solubility. Such a mismatch may however be accounted for either slowing the dehydration rate with use of a narrower Knudsen orifice, or correcting the experimental a W with a calibration curve. The same approach can be applied to non-aqueous solutions

Salicylimine-Based Colorimetric and Fluorescent Chemosensor for Selective Detection of Cyanide in Aqueous Buffer

Energy Technology Data Exchange (ETDEWEB)

Noh, Jin Young; Hwang, In Hong; Kim, Hyun; Song, Eun Joo; Kim, Kyung Beom; Kim, Cheal [Seoul National Univ., Seoul (Korea, Republic of)

2013-07-15

A simple colorimetric and fluorescent anion sensor 1 based on salicylimine showed a high selectivity and sensitivity for detection of cyanide in aqueous solution. The receptor 1 showed high selectivity toward CN{sup -} ions in a 1:1 stoichiometric manner, which induces a fast color change from colorless to orange and a dramatic enhancement in fluorescence intensity selectively for cyanide anions over other anions. Such selectivity resulted from the nucleophilic addition of CN{sup -} to the carbon atom of an electron-deficient imine group. The sensitivity of the fluorescence-based assay (0.06 μM) is below the 1.9 μM suggested by the World Health Organization (WHO) as the maximum allowable cyanide concentration in drinking water, capable of being a practical system for the monitoring of CN. concentrations in aqueous samples.

Dinitrosyl iron complexes with natural thiol-containing ligands in aqueous solutions: Synthesis and some physico-chemical characteristics (A methodological review).

Science.gov (United States)

Vanin, Anatoly F; Borodulin, Rostislav R; Mikoyan, Vasak D

2017-06-01

Two approaches to the synthesis of dinitrosyl iron complexes (DNIC) with glutathione and l-cysteine in aqueous solutions based on the use of gaseous NO and appropriate S-nitrosothiols, viz., S-nitrosoglutathione (GS-NO) or S-nitrosocysteine (Cys-NO), respectively, are considered. A schematic representation of a vacuum unit for generation and accumulation of gaseous NO purified from the NO 2 admixture and its application for obtaining aqueous solutions of DNIC in a Thunberg apparatus is given. To achieve this, a solution of bivalent iron in distilled water is loaded into the upper chamber of the Thunberg apparatus, while the thiol solution in an appropriate buffer (рН 7.4) is loaded into its lower chamber. Further steps, which include degassing, addition of gaseous NO, shaking of both solutions and formation of the Fe 2+ -thiol mixture, culminate in the synthesis of DNIC. The second approach consists in a stepwise addition of Fe 2+ salts and nitrite to aqueous solutions of glutathione or cysteine. In the presence of Fe 2+ and after the increase in рН to the physiological level, GS-NO or Cys-NO generated at acid media (pH nitrosonium ions (NO + ) and the peculiar characteristics of the EPR signal of their mononuclear form (M-DNIC). Copyright © 2017. Published by Elsevier Inc.

Ozonation of aqueous solution containing bisphenol A: Effect of operational parameters

International Nuclear Information System (INIS)

Garoma, Temesgen; Matsumoto, Shinsyu

2009-01-01

The degradation of bisphenol A (BPA) in aqueous solution by ozonation was studied. The study was conducted experimentally in a semi-batch reactor under different operational conditions, i.e., varying influent ozone gas concentration, initial BPA concentration, pH, and bicarbonate ion concentration. The results of the study indicated that ozonation could be used to effectively remove BPA from contaminated water. Keeping other operational parameters constant, the rate of BPA degradation linearly increased with ozone dosage. At pH value of 7.0, the second-order rate constants for the reaction of BPA with aqueous ozone were determined as 1.22 x 10 5 , 1.71 x 10 5 , and 2.59 x 10 5 M -1 s -1 for ozone gas dosages of 1.4, 2.2, and 5.1 mg L -1 , respectively. Bicarbonate ion in the range of 1.0-8.0 mM (61-488 ppm) showed no significant effect on BPA degradation for concentrations of BPA used in the study (23.0-57.0 μM). It was also observed that the rate of BPA degradation increased with pH up to 7.0, resulting in rate constants of 0.48 x 10 5 , 0.94 x 10 5 , and 1.71 x 10 5 M -1 s -1 at pH values of 2.0, 5.0, and 7.0, respectively; and the rate constant decreased to 1.16 x 10 5 M -1 s -1 at pH of 10.0.

Pulse electrodeposition of Pt and Pt–Ru methanol-oxidation nanocatalysts onto carbon nanotubes in citric acid aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Chou, Huei-Yu [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Hsieh, Chien-Kuo [Department of Materials Engineering, Ming Chi University of Technology, New Taipei City 24301, Taiwan, ROC (China); Tsai, Ming-Chi; Wei, Yu-Hsuan; Yeh, Tsung-Kuang [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Tsai, Chuen-Horng, E-mail: tsai@aec.gov.tw [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China)

2015-06-01

In this study, platinum nanoparticle/carbon nanotube (Pt NP/CNT) and platinum–ruthenium nanoparticle (Pt–Ru NP/CNT) hybrid nanocatalysts were prepared by the pulse-electrodeposition method in different aqueous solutions containing citric acid (CA) or sulfuric acid (SA). The electrocatalytic properties of the Pt NP/CNT and Pt–Ru NP/CNT electrodes prepared using different aqueous solutions were investigated for methanol oxidation. The results show that the electrochemical mass activities of these hybrid nanocatalysts prepared in the CA aqueous solution were increased by factors of 1.46 and 2.77 for Pt NPs and Pt–Ru NPs, respectively, compared with those prepared in SA aqueous solutions using the same procedure. These increased mass activities are attributed to the CA playing dual roles as both a stabilizing agent and a particle size reducing agent in the aqueous solutions. The approach developed in this work enables further reductions in the particle sizes of noble-metal nanocatalysts. - Highlights: • Pulse-electrodeposition of Pt or Pt–Ru nanoparticles on carbon nanotubes • Carbon nanotubes used as a catalyst-supporting material • Citric acid used as reducing agent in the aqueous electrodeposition solutions • Electrochemical activity for methanol oxidation improved by a factor of 1.46 to 2.77.

Radiolysis of aqueous solutions of insulin. [. gamma. rays

Energy Technology Data Exchange (ETDEWEB)

Foitik, A [Ceskoslovenska Akademie Ved, Prague. Ustav Fyzikalni Chemie a Elektrochemie J. Heyrovskeho; Kopoldova, J [Ceskoslovenska Akademie Ved, Prague. Isotopova Laborator Biologickych Ustavu

1976-08-01

The effect of ionizing radiation on diluted aqueous solutions of insulin is analyzed. The rate of decrease in its level (the loss of polarographic activity) is described by a first-order kinetic equation. The results lead to the concept of a direct effect on macromolecules in 'excited volumes'. The amount of inactivated molecules (i.e., the yield) in this volume is proportional to the solute concentration. In diluted aqueous solutions indirect radiation effects also take place. The paper evaluates these effects.

Determination of Ga in aqueous uranium solution by EDXRF

International Nuclear Information System (INIS)

Natarajan, V.; Purohit, P.J.; Goyal, Neelam; Seshagiri, T.K.; Godbole, S.V.; Manchanda, V.K.

2009-01-01

A method has been developed using EDXRF technique for the determination of gallium in aqueous solution using a set of solution standards in the concentration range 20-5000 μg/ml. When this method was applied to U containing solutions, the estimated values were found to be lower due to matrix effects. Hence the method was modified in order to determine gallium in the presence of uranium using lower tube current and another set of standards with U concentration at 100 mg/ml. The method was applicable for the estimation of Ga from 50 μg/ml to 5mg/ml (i.e.0.05-5% Ga in U). Three synthetic samples were analysed by the present methods in order to evaluate the method for its reliability and reproducibility. (author)

Enhanced electrochemical performances of PANI using redox additive of K{sub 4}[Fe(CN){sub 6}] in aqueous electrolyte for symmetric supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Shanmugavani, A.; Kaviselvi, S.; Sankar, K.Vijaya; Selvan, R.Kalai, E-mail: selvankram@buc.edu.in

2015-02-15

Highlights: • Effect of K{sub 4}[Fe(CN){sub 6}] in H{sub 2}SO{sub 4} studied on the electrochemical properties of PANI. • The polaron band – π* transition reveals the emeraldine salt (conductive) form. • CV curves exhibit quasi-reversible redox behavior. • Symmetric PANI SC shows 228 F g{sup −1} at 1 mA cm{sup −2} in K{sub 4}[Fe (CN){sub 6}] added 1 M H{sub 2}SO{sub 4}. • PANI-1 symmetric supercapacitor shows almost 100% of capacity retention. - Abstract: Polyaniline (PANI) particles were prepared by reflux assisted chemical oxidative polymerization method with the aid of ammonium per sulfate/ferric chloride as oxidants and HCl/H{sub 2}SO{sub 4} as the medium. Amorphous nature and the emeraldine state of PANI were revealed from X-ray diffraction and Fourier transform infrared analysis. Moreover, ultra violet–visible spectra attributes to the polaron band – π* transition of polyaniline. The scanning electron microscopic image shows that the particle size is in the range of 0.2–2 μm. The electrochemical performances of the material were investigated in 1 M H{sub 2}SO{sub 4} and 0.08 M K{sub 4}[Fe(CN){sub 6}] added 1 M H{sub 2}SO{sub 4} aqueous electrolytes. Cyclic voltammetry and galvanostatic charge–discharge studies were carried out to find its suitability as a supercapacitor electrode material. The charge discharge analysis of the fabricated symmetric supercapacitors revealed the fact that the electrolyte containing redox additive (0.08 M K{sub 4}[Fe(CN){sub 6}]) delivered an enhanced specific capacitance of 228 F g{sup −1} (∼912 F g{sup −1} for single electrode) than that of 1 M H{sub 2}SO{sub 4} (100 F g{sup −1}) at 1 mA cm{sup −2}. Further cycling stability is performed at 5 mA cm{sup −2} ensures the durability of the supercapacitor.

Phase equilibrium properties of binary aqueous solutions containing ethanediamine, 1,2-diaminopropane, 1,3-diaminopropane, or 1,4-diaminobutane at several temperatures

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Nouria Chiali-Baba [LATA2M, Laboratoire de Thermodynamique Appliquee et Modelisation Moleculaire, University AbouBekr Belkaid of Tlemcen, P.O. Box 119, Tlemcen 13000 (Algeria); Negadi, Latifa, E-mail: l_negadi@mail.univ-tlemcen.d [LATA2M, Laboratoire de Thermodynamique Appliquee et Modelisation Moleculaire, University AbouBekr Belkaid of Tlemcen, P.O. Box 119, Tlemcen 13000 (Algeria); Mokbel, Ilham; Jose, Jacques [LSA, Laboratoire des Sciences Analytiques, CNRS-UMR 5180, Universite Claude Bernard - Lyon I. 43, Bd du 11 Novembre 1918, Villeurbanne Cedex 69622 (France)

2011-05-15

Research highlights: Vapour pressures of ethanediamine (EDA), 1,2-diaminopropane, 1,3-diaminopropane (1,3-DAP), or 1,4-diaminobutane (1,4-DAB) aqueous solutions are reported between (293 and 363) K. The two first mixtures show negative azeotropic behaviour. The aqueous solutions of EDA, 1,2-DAP, or 1,3-DAP exhibit negative G{sup E} whereas the one containing 1,4-DAB shows either negative G{sup E} or sinusoidal shape for G{sup E}. - Abstract: The vapour pressures of {l_brace}ethanediamine (EDA) + water{r_brace}, {l_brace}1,2-diaminopropane (1,2-DAP) + water{r_brace}, {l_brace}1,3-diaminopropane (1,3-DAP) + water{r_brace} or {l_brace}1,4-diaminobutane (1,4-DAB) + water{r_brace} binary mixtures, and of pure EDA, 1,2-DAP, 1,3-DAP, 1,4-DAB, and water components were measured by means of two static devices at temperatures between (293 and 363) K. The data were correlated with the Antoine equation. From these data, the excess Gibbs function (G{sup E}) was calculated for several constant temperatures and fitted to a fourth-order Redlich-Kister equation using the Barker's method. The {l_brace}ethanediamine (EDA) + water{r_brace}, and {l_brace}1,2-diaminopropane (1,2-DAP) + water{r_brace} binary systems show negative azeotropic behaviour. The aqueous solutions of EDA, 1,2-DAP, or 1,3-DAP exhibit negative deviations in G{sup E} for all investigated temperatures over the whole composition range whereas the (1,4-DAB + water) binary mixture shows negative G{sup E} for temperatures (293.15 < T/K < 353.15) and a sinusoidal shape for G{sup E} at T = 363.15 K.

Method of separation of uranium from contaminating ions in an aqueous feed liquid containing uranyl ions

International Nuclear Information System (INIS)

Sundar, P.S.; Elikan, L.; Lyon, W.L.

1975-01-01

A coupled cationic/anionic method for the separation of uranium from contaminated aqueous solutions which contain uranyl ions is proposed. The fluid is extracted using an organic solvent containing a reagent which, together with the uranyl ions, forms a soluble aggregate in that solvent. As an example, 0.1 - 1 Mol/l Di-2-ethyl-hexyl-phosphorous acid in kerosene is mentioned. The organic solvent is then treated with a sealing liquid (volume ratio 20 - 35). For separation, an aqueous carbonate solution or a sulfuric acid solution can be used; the most favorable pH-values and concentrations for both cases are mentioned. The U +4 -ion at the sulfuric acid separation is subsequently oxidized to the uranyl ion with air. In each case, an extraction with an amine follows; after that, the amine is separated using an ammonium-carbonate solution and the uranium aggregate is precipitated, for example as ammonium uranyl tricarbonate, and then further processed to uranium oxide. The solvents and fluids used are led back in closed circuit; a flow diagram is given. (UWI) [de

Formation of hydrated layers in PMMA thin films in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Akers, Peter W. [School of Chemical Sciences, University of Auckland, Auckland (New Zealand); Nelson, Andrew R.J. [The Bragg Institute, Australian Nuclear Science and Technology Organisation, Menai, NSW (Australia); Williams, David E. [School of Chemical Sciences, University of Auckland, Auckland (New Zealand); MacDiarmid Institute of Advanced Materials and Nanotechnology, Wellington (New Zealand); McGillivray, Duncan J., E-mail: d.mcgillivray@auckland.ac.nz [School of Chemical Sciences, University of Auckland, Auckland (New Zealand); MacDiarmid Institute of Advanced Materials and Nanotechnology, Wellington (New Zealand)

2015-10-30

Graphical abstract: - Highlights: • Homogeneous thin PMMA films prepared on Si/SiOx substrates and measured in air and water. • Reproducible formation of highly hydrated layer containing 50% water at the PMMA/SiOx interface. • When heated the films swell at 50 °C without loss of material. • Upon re-cooling to 25 °C the surface roughens and material is lost. - Abstract: Neutron reflectometry (NR) measurements have been made on thin (70–150 Å) poly(methylmethacrylate) (PMMA) films on Si/SiOx substrates in aqueous conditions, and compared with parameters measured using ellipsometry and X-Ray reflectometry (XRR) on dry films. All techniques show that the thin films prepared using spin-coating techniques were uniform and had low roughness at both the silicon and subphase interfaces, and similar surface energetics to thicker PMMA films. In aqueous solution, NR measurements at 25 °C showed that PMMA forms a partially hydrated layer at the SiOx interface 10 Å under the film, while the bulk film remains intact and contains around 4% water. Both the PMMA film layer and the sublayer showed minimal swelling over a period of 24 h. At 50 °C, PMMA films in aqueous solution roughen and swell, without loss of PMMA material at the surface. After cooling back to 25 °C, swelling and roughening increases further, with loss of material from the PMMA layer.

Formation of hydrated layers in PMMA thin films in aqueous solution

International Nuclear Information System (INIS)

Akers, Peter W.; Nelson, Andrew R.J.; Williams, David E.; McGillivray, Duncan J.

2015-01-01

Graphical abstract: - Highlights: • Homogeneous thin PMMA films prepared on Si/SiOx substrates and measured in air and water. • Reproducible formation of highly hydrated layer containing 50% water at the PMMA/SiOx interface. • When heated the films swell at 50 °C without loss of material. • Upon re-cooling to 25 °C the surface roughens and material is lost. - Abstract: Neutron reflectometry (NR) measurements have been made on thin (70–150 Å) poly(methylmethacrylate) (PMMA) films on Si/SiOx substrates in aqueous conditions, and compared with parameters measured using ellipsometry and X-Ray reflectometry (XRR) on dry films. All techniques show that the thin films prepared using spin-coating techniques were uniform and had low roughness at both the silicon and subphase interfaces, and similar surface energetics to thicker PMMA films. In aqueous solution, NR measurements at 25 °C showed that PMMA forms a partially hydrated layer at the SiOx interface 10 Å under the film, while the bulk film remains intact and contains around 4% water. Both the PMMA film layer and the sublayer showed minimal swelling over a period of 24 h. At 50 °C, PMMA films in aqueous solution roughen and swell, without loss of PMMA material at the surface. After cooling back to 25 °C, swelling and roughening increases further, with loss of material from the PMMA layer.

Use of metallurgical dust for removal chromium ions from aqueous solutions

Science.gov (United States)

Pająk, Magdalena; Dzieniszewska, Agnieszka; Kyzioł-Komosińska, Joanna; Chrobok, Michał

2018-01-01

The aim of the study was to determine the potential for the application of dust from steel plant as an effective sorbent for removing Cr(III) and Cr(VI) in the form of simple and complex ions - Acid Blue 193 dye from aqueous solutions. Three isotherms models were used to interpret the experimental results namely: Langmuir, Freundlich, and Dubinin-Radushkevich. Estimated equations parameters allowed to determine the binding mechanism. Based on laboratory studies it was found that the dust was characterized by high sorption capacities for Cr ions and dye from the aqueous solution. The sorption capacity of the dust for Cr(III) and Cr(VI) ions depended on the degree of oxidation, pH of solution and kind of anion and changed in series: Cr(III)-Cl pH=5.0> Cr(III)-SO4 pH=5.0> Cr(III)-Cl pH=3.0> Cr(III)-SO4 pH=3.0> Cr(VI) pH=5.0> Cr(VI) pH=3.0. Dust was also characterized by a high maximum sorption capacity of dye at a range of 38.2 - 91.7 mg/g, depending on the dose of dust. Based on the study it was found that dust from a steel plant, containing iron oxides, can be used as low-cost and effective sorbent to remove pollutions containing chromium ions, especially from acidic wastewater.

Acetic acid extraction from aqueous solutions using fatty acids

NARCIS (Netherlands)

IJmker, H.M.; Gramblicka, M.; Kersten, Sascha R.A.; van der Ham, Aloysius G.J.; Schuur, Boelo

2014-01-01

A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

Simultaneous removal and recovery of uranium from aqueous solution using TiO_2 photoelectrochemical reduction method

International Nuclear Information System (INIS)

Huichao He; Meirong Zong; Faqin Dong; Southwest University of Science and Technology, Sichuan; Pengpan Yang; Gaili Ke; Mingxue Liu; Xiaoqin Nie; Wei Ren; Liang Bian; Southwest University of Science and Technology, Sichuan; Chinese Academy of Sciences, Xinjiang

2017-01-01

U(VI)-containing wastewater has potential radiation hazard to the environment, but contains valuable uranium resource. Based on the reduction of U(VI) and the difference in solubility between U(VI) and U(IV), here we construct a TiO_2-based photoelectrochemical cell to remove U(VI) and recover uranium from aqueous solution. By irradiating TiO_2 photoanode at E = 0.45 V versus SCE, U(VI) can be simultaneously removed from aqueous solution and recovered as solid uranium compounds on a FTO glass cathode. Since ethanol can act as hole scavenger to protect the formed U(IV) and provide CO_2"−"· as reductant, ethanol adding improved the U(VI) reduction efficiency of TiO_2-based photoelectrochemical cell. (author)

Photolysis of Periodate and Periodic Acid in Aqueous Solution

DEFF Research Database (Denmark)

Sehested, Knud; Kläning, U. K.

1978-01-01

The photochemistry of periodate and periodic acid in aqueous solution was studied (i) by quantum yield measurements at low light intensity (ii) by flash photolysis, and (iii) by photolysis of glassy samples at 77 K. The photochemical studies were supplemented with pulse radiolysis studies...... of aqueous periodate solutions and with kinetic studies using stopped-flow technique. In strongly alkaline solution the photodecomposition of periodate proceeds via formation of O– and IVI. At pH solution O3 P is formed in a small...

Method of precipitating uranium from an aqueous solution and/or sediment

Science.gov (United States)

Tokunaga, Tetsu K; Kim, Yongman; Wan, Jiamin

2013-08-20

A method for precipitating uranium from an aqueous solution and/or sediment comprising uranium and/or vanadium is presented. The method includes precipitating uranium as a uranyl vanadate through mixing an aqueous solution and/or sediment comprising uranium and/or vanadium and a solution comprising a monovalent or divalent cation to form the corresponding cation uranyl vanadate precipitate. The method also provides a pathway for extraction of uranium and vanadium from an aqueous solution and/or sediment.

Study of free acidity determinations in aqueous solution

International Nuclear Information System (INIS)

Kergreis, A.

1966-04-01

The object of this work is the study of the principal methods which can be applied to the measurement of 'free' acidity. In the first part, we define the various types of acidity which can exist in aqueous solution; then, after having studied some hydrolysis reactions, we compare the value of the neutralisation pH of the hydrated cation and that of the precipitation of the hydroxide. In the second part we have started to study the determination of the acidity of an aqueous solution. After having rapidly considered the 'total' acidity determination, we deal with the problem of the 'free' acidity titration. We have considered in particular certain methods: extrapolation of the equivalent point, colorimetric titrations with or without a complexing agent, and finally the use of ion-exchange resins with mixed aqueous and solvent solutions. (author) [fr

Principles of interactions in non-aqueous electrolyte solutions

NARCIS (Netherlands)

Lyklema, J.

2013-01-01

In this paper a review is presented on the molecular interactions in non-aqueous media of low dielectric permittivity. Qualitative and quantitative distinctions with aqueous solutions are emphasized. The reviewed themes include dispersion forces, dissociation and association equilibria,

Experimental measurements of U24Py nanocluster behavior in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Flynn, Shannon L.; Szymanowski, Jennifer E.S.; Fein, Jeremy B. [Univ. of Notre Dame, IN (United States). Department of Civil and Environmental Engineering and Earth Sciences; Dembowski, Mateusz [Univ. of Notre Dame, IN (United States). Department of Chemistry and Biochemistry; Burns, Peter C. [Univ. of Notre Dame, IN (United States). Department of Civil and Environmental Engineering and Earth Sciences; Univ. of Notre Dame, IN (United States). Department of Chemistry and Biochemistry

2016-07-01

Uranyl peroxide nanoclusters may impact the mobility and partitioning of uranium at contaminated sites and could be used in the isolation of uranium during the reprocessing of nuclear waste. Their behavior in aqueous systems must be better understood to predict the environmental fate of uranyl peroxide nanoclusters and for their use in engineered systems. The aqueous stability of only one uranyl peroxide nanocluster, U60 (K{sub 16}Li{sub 44}[UO{sub 2}(O{sub 2})OH]{sub 60}), has been studied to date [Flynn, S. L., Szymanowski, J. E. S., Gao, Y., Liu, T., Burns, P. C., Fein, J. B.: Experimental measurements of U60 nanocluster stability in aqueous solution. Geochemica et Cosmochimica Acta 156, 94-105 (2015)]. In this study, we measured the aqueous stability of a second uranyl peroxide nanocluster, U24Py (Na{sub 30}[(UO{sub 2}){sub 24}(O{sub 2}){sub 24}(HP{sub 2}O{sub 7}){sub 6}(H{sub 2}P{sub 2}O{sub 7}){sub 6}]), in batch systems as a function of time, pH, and nanocluster concentration, and then compared the aqueous behavior of U24Py to U60 to determine whether the size and morphology differences result in differences in their aqueous behaviors. Systems containing U24Py nanoclusters took over 30 days to achieve steady-state concentrations of monomeric U, Na, and P, illustrating slower reaction kinetics than parallel U60 systems. Furthermore, U24Py exhibited lower stability in solution than U60, with an average of 72% of the total mass in each nanocluster suspension being associated with the U24Py nanocluster, whereas 97% was associated with the U60 nanocluster in parallel experiments [Flynn, S. L., Szymanowski, J. E. S., Gao, Y., Liu, T., Burns, P. C., Fein, J. B.: Experimental measurements of U60 nanocluster stability in aqueous solution. Geochemica et Cosmochimica Acta 156, 94-105 (2015)]. The measurements from the batch experiments were used to calculate ion activity product (IAP) values for the reaction between the U24Py nanocluster and its constituent monomeric

Process for removing a mixture containing iodine and alkyl iodine compounds from a gas phase or aqueous solution with ion-exchange resins

Energy Technology Data Exchange (ETDEWEB)

Shimizu, H; Mizuuchi, A; Yokoyama, F

1968-10-04

Iodine and alkyl iodine compounds are removed from a gas phase or aqueous solution containing salts, iodine and iodine compounds, such as the ambient gas in a reactor, if an accident should occur. The process comprises contacting the phase or solution: (a) with a hydrogen type strongly acidic cationic exchange resin, (b) with an anionic exchange resin containing quarternary ammonium and (c) with an anionic exchange resin containing free basic type tertiary amine, in this order or by reversing the order of the two anionic exchange resins. Although no problems arise in the liquid phase reaction, the ion-exchange resins in the gas phase reaction are desired in the moist state in order to stable maintain the migration speed of the materials to be removed regardless of the relative humidity of the amibent gas. In example I, Amberlite IRA-900 of 200 mm thickness as the lowermost bed, Amberlite IRA93 of 200 mm thickness as the middle bed and Amberlite 200 of 200 mm thickness as the uppermost bed were filled respectively, in a methacrylate resin cylinder with an inner diameter of 25 mm. A solution containing 15.9 mg/1 of iodine, 41.2 mg/1 of methyl iodide and 550 mg/1 of sodium carbonate flows at a rate of 15 liter/hr downward through the beds. As a result of testing, no iodine, iodine ions, iodic acid ions and methyl iodine were detected. The amount of water the beds could treat was 60 times the total quantity of the filled resins.

Solvation consequences of polymer PVP with biological buffers MES, MOPS, and MOPSO in aqueous solutions

International Nuclear Information System (INIS)

Gupta, Bhupender S.; Chen, Bo-Ren; Lee, Ming-Jer

2015-01-01

Highlights: • Densities and viscosities data for aqueous solutions with PVP and/or buffer. • The studied buffers include MES, MOPS, and MOPSO. • DFT was used to estimate the binding energies of the (PVP + buffer) complexes. • The viscosity data were correlated with the Jones–Dole equation. • The investigated buffers behave as Kosmotropies. - Abstract: Densities and viscosities were measured for the aqueous buffer (MES, MOPS, or MOPSO) solutions containing different concentrations of polyvinylpyrrolidone (PVP) (5, 10, 15, 20 and 30) mass% at temperatures from (298.15 to 318.15) K under atmospheric pressure. The DFT calculations were also performed and the binding energies of the possible (PVP + buffer) complexes were obtained. The experimental and computational results reveal the interactions of the PVP with the constituent compounds in the aqueous buffer solutions. Additionally we have explored the solvation behavior of the buffers by measuring the densities and the viscosities data of the aqueous buffer solutions from (0.0 to 1.0) mol · kg"−"1 at temperatures from (298.15 to 318.15) K. The viscosity results were correlated with the Jones–Dole equation. The correlated results confirmed that all the investigated buffers behave as Kosmotropes (structure makers).

Arsenic (III Adsorption Using Palladium Nanoparticles from Aqueous Solution

Directory of Open Access Journals (Sweden)

Farzaneh Arsiya

2017-07-01

Full Text Available The presence of Arsenic in drinking water is the greatest threat to health effects especially in water. The purpose of this study is application of green palladium nanoparticles for removal of trivalent Arsenic from aqueous solutions and also the impact of some factors such as retention time, pH, concentration of palladium nanoparticles and Arsenic concentrations was studied. The values for Arsenic removal from aqueous solutions were measured by furnace atomic adsorption spectrometry (Conter AA700. In the study, Langmuir and Freundlich isotherm models and pseudo-second order kinetic model were studied. The results of  optimization is shown that 0.5 g of nanoparticles can removed %99.8 of Arsenic with initial concentration of  0.5 g/l, in 5 minutes at pH=4. Langmuir model, Freundlich model (R2=0.94 and pseudo-second order kinetic model (R2=0.99 shown high correlation for removing of Arsenic from aqueous solutions. It was found, palladium nanoparticles can be used as an efficient method to remove Arsenic from aqueous solutions in a short time.

On the state of phosphomolybdenovanadic heteropolyblue in aqueous solutions

International Nuclear Information System (INIS)

Kuznetsova, L.I.; Yurchenko, Eh.N.; Maksimovskaya, R.I.; Kirik, N.P.; Matveev, K.I.

1977-01-01

The effect has been investigated of pH solution on the state of the phosphomolybdenovanadic heteropolyblues of the 12. series, containing n=1,2,3,6 atoms of vanadium (6). It has been shown that the free VO 2+ intrusion into the sphere of heteropolyanions takes place alongside with pH increasing from 1 to 3. At the some time the rate of oxidation of the heteropolyblue solutions by oxygen and the optical density of solutions increase too. The dissociation constants of the heteropolyblue molecule in acid medium increase with increasing of the quantity of vanadium atoms. It has been shown that stability of heteropolyblue in relation to molybdenum decreases with increasing of its quantity in the heteropolyblue molecule. Using precipitation of the heteropolyanions by the cation of tetraethyl ammonium, it has been shown that heteropolyanions can consist of 1,2,3 and 6 atoms of V(6). The state of heteropolyblues in an aqueous solution is characterized by electron absorption spectra

Reactions of vanadium(5) with aluminium(3) in weakly acid aqueous solutions

International Nuclear Information System (INIS)

Ditrikh, I.V.; Makhno, A.Ya.

1996-01-01

Conditions of vanadium(5) heteropolycompounds formation in aqueous solutions containing aluminium(3) have been studied. By the methods of potentiometry and conductometry in solutions of Al(NO 3 ) 3 -NaVO 3 salt mixture the formation of complexes with the ratios [Al 3+ ]:[V 5+ ]=1:3, 1:6 and 1:12 has been ascertained. A salt of gross formula 3NaO · Al 2 ) 3 · 12V 2 O 5 · 67H 2 O has been isolated. 3 refs.; 2 figs

Studies on the Use of Oyster, Snail and Periwinkle Shells as Adsorbents for the Removalof Pb2+ Aqueous Solution

Directory of Open Access Journals (Sweden)

Stevens A. Odoemelam

2009-01-01

Full Text Available In view of increasing rate of lead pollution resulting from discharge of lead containing effluents by industries into the environment, this study was carried out to investigate the removal of Pb2+ from aqueous solutions by oyster, snail and periwinkle shells. The effects of contact time and concentration on adsorption, thermodynamics of sorption and distribution coefficients of the adsorbents were examined to optimize the conditions to be utilized for decontamination of effluents containing Pb2+. The study revealed that these materials are good adsorbents that can be used for the removal of Pb2+ from aqueous solution. Adsorption of Pb2+ by oyster, snail and periwinkle shells were found to conform to the classical models of Langmuir, Freundlich and Temkin adsorption isotherms. Thermodynamic consideration revealed that adsorption of Pb2+ by these materials was spontaneous and proceeded via chemical adsorption. The use of these materials for the removal of lead ion from aqueous solution is therefore advocated

An SFG and DFG investigation of polycrystalline Au, Au-Cu and Au-Ag-Cu electrodes in contact with aqueous solutions containing KCN

International Nuclear Information System (INIS)

Bozzini, Benedetto; Busson, Bertrand; De Gaudenzi, Gian Pietro; Mele, Claudio; Tadjeddine, Abderrahmane

2007-01-01

In this paper, the behaviour of polycrystalline Au, Au-Cu (Cu 25%) and Au-Ag-Cu (Ag 10%, Cu 15%) electrodes in contact with neutral aqueous solutions of KCN has been studied as a function of potential by means of in situ sum frequency generation (SFG) and difference frequency generation (DFG) spectroscopies. The potential-dependent spectra have been analysed quantitatively with a model for the second-order non-linear susceptibility accounting for vibrational and electronic effects. The potential-dependence of the CN - stretching band position and of the free-electron contribution to the real part of the non-resonant component of the second-order susceptibility have been accounted for. Spectroelectrochemical results were complemented by cyclic voltammetric measurements. The chief stress in this work has been placed on systematising and quantifying the interaction between the vibrational and electronic structures of the electrodic interfaces studied. The effects of adsorbates on the electronic structure of the adsorbing electrode, as a function of electrode alloy composition and applied potential are particularly critical for the understanding of Au-alloy electrochemistry in the presence of cyanide and cyanocomplexes. The systematic comparison of SFG and DFG spectra measured under the same electrochemical conditions for Au, Au-Cu and Au-Ag-Cu electrodes discloses a rich phenomenology related to the electronic structure of the interface

An SFG and DFG investigation of polycrystalline Au, Au-Cu and Au-Ag-Cu electrodes in contact with aqueous solutions containing KCN

Energy Technology Data Exchange (ETDEWEB)

Bozzini, Benedetto [Dipartimento di Ingegneria dell' Innovazione, Universita di Lecce, v. Monteroni, I-73100 Lecce (Italy)]. E-mail: benedetto.bozzini@unile.it; Busson, Bertrand [CLIO-LCP, Universite Paris-Sud, 91405 Orsay Cedex (France); De Gaudenzi, Gian Pietro [Dipartimento di Ingegneria dell' Innovazione, Universita di Lecce, v. Monteroni, I-73100 Lecce (Italy); Mele, Claudio [Dipartimento di Ingegneria dell' Innovazione, Universita di Lecce, v. Monteroni, I-73100 Lecce (Italy); Tadjeddine, Abderrahmane [UDIL-CNRS, Bat. 201, Centre Universitaire Paris-Sud, BP 34, 91898 Orsay Cedex (France)

2007-01-16

In this paper, the behaviour of polycrystalline Au, Au-Cu (Cu 25%) and Au-Ag-Cu (Ag 10%, Cu 15%) electrodes in contact with neutral aqueous solutions of KCN has been studied as a function of potential by means of in situ sum frequency generation (SFG) and difference frequency generation (DFG) spectroscopies. The potential-dependent spectra have been analysed quantitatively with a model for the second-order non-linear susceptibility accounting for vibrational and electronic effects. The potential-dependence of the CN{sup -} stretching band position and of the free-electron contribution to the real part of the non-resonant component of the second-order susceptibility have been accounted for. Spectroelectrochemical results were complemented by cyclic voltammetric measurements. The chief stress in this work has been placed on systematising and quantifying the interaction between the vibrational and electronic structures of the electrodic interfaces studied. The effects of adsorbates on the electronic structure of the adsorbing electrode, as a function of electrode alloy composition and applied potential are particularly critical for the understanding of Au-alloy electrochemistry in the presence of cyanide and cyanocomplexes. The systematic comparison of SFG and DFG spectra measured under the same electrochemical conditions for Au, Au-Cu and Au-Ag-Cu electrodes discloses a rich phenomenology related to the electronic structure of the interface.

Use of metallurgical dust for removal chromium ions from aqueous solutions

Directory of Open Access Journals (Sweden)

Pająk Magdalena

2018-01-01

Full Text Available The aim of the study was to determine the potential for the application of dust from steel plant as an effective sorbent for removing Cr(III and Cr(VI in the form of simple and complex ions – Acid Blue 193 dye from aqueous solutions. Three isotherms models were used to interpret the experimental results namely: Langmuir, Freundlich, and Dubinin–Radushkevich. Estimated equations parameters allowed to determine the binding mechanism. Based on laboratory studies it was found that the dust was characterized by high sorption capacities for Cr ions and dye from the aqueous solution. The sorption capacity of the dust for Cr(III and Cr(VI ions depended on the degree of oxidation, pH of solution and kind of anion and changed in series: Cr(III-Cl pH=5.0> Cr(III-SO4 pH=5.0> Cr(III-Cl pH=3.0> Cr(III-SO4 pH=3.0> Cr(VI pH=5.0> Cr(VI pH=3.0. Dust was also characterized by a high maximum sorption capacity of dye at a range of 38.2 – 91.7 mg/g, depending on the dose of dust. Based on the study it was found that dust from a steel plant, containing iron oxides, can be used as low-cost and effective sorbent to remove pollutions containing chromium ions, especially from acidic wastewater.

Reverse osmosis separation of radium from dilute aqueous solutions

International Nuclear Information System (INIS)

Subramanian, K.S.; Sastri, V.S.

1980-01-01

Porous cellulose acetate membranes obtained from Osmonics Inc. were characterized in terms of pure water permeability constant, solute transport parameter, and mass transfer coefficient with aqueous sodium chloride solution as the reference system. Reverse osmosis separation behavior of radium-226 as nitrate, chloride, and sulfate salts was studied. Reverse osmosis method of removing radium-226 from aqueous solutions has been compared with other methods, and it has been shown to be one of the best methods for alleviating radium contamination problems

Process for plutonium rextraction in aqueous solution from an organic solvent, especially for uranium plutonium partition

International Nuclear Information System (INIS)

Germain, M.; Gillet, B.; Pasquiou, J.Y.

1989-01-01

The organic solvent containing plutonium is contacted with an aqueous solution of a uranous salt, for instance uranous nitrate, and a hydroxylamine salt, for instance the nitrate. In these conditions uranous nitrate is a reducing agent of Pu III and hydroxylamine nitrate stabilizes Pu III and U IV in the aqueous phase. Performances are similar to these of the U IV-hydrazine nitrate without interference of hydrazine nitrate degradation products [fr

OPTICAL PROPERTIES OF CARBAMIDE AQUEOUS SOLUTIONS

Directory of Open Access Journals (Sweden)

E. V. Avramenko

2016-03-01

Full Text Available Subject of Research. The paper presents the results of measurements of refractometric properties (refractive index n, its temperature factor dn/dt and the ultraviolet spectral absorption in carbonic acid diamide aqueous solutions (carbamide depending on solid residue mass fraction md = 0-50 % and on temperaturet = 10-70 °C.Method of Research. Laboratory methods ofliquid-phase medium refractometry and ultraviolet spectrophotometry were applied for the research. We carried out computational modeling of electronic states spectrum for the carbonic acid diamide molecule and theoretical calculation of the fundamental electronic absorption of the molecule in the ultraviolet wavelenght region.Main Results. We have established that the solution concentration md has a nonlinear character and may be represented by the quadratic polynomial with the error Δn= ± 0,0005. We have shown the refractive indexdependence on temperature n(t changes in linear fashion att = 10-70 °C.At that, the inclination of lines n(t increases at the increase of md; so, the temperature factor dn/dt may be approximated by the quadratic polynomial. Transmission spectra of solutions in the spectral region λ= 225-760 nm have no special features except for the sharp edge in the short-wavelength region; the fundamental electronic absorptionis responsible for it. We have established that dispersion dependences of the refraction index n(λ;md in aqueous solutions of carbamide at λ= 360-760 nm and at md = 0-50 % may be calculated with the satisfactory error without additional adjustable parameters from the ultraviolet absorption data in terms of the one-dimentional oscillator Lorentz model.PracticalRelevance. Representedmeasurements of carbonic acid diamide aqueous solutions optical properties may be applied for the adjustment and calibration of commercial refractometers at processing lines of the AdBlue reagent manufacture for the selective catalytic reduction (SCR of motor transport

Aqueous solutions/nuclear glasses interactions

International Nuclear Information System (INIS)

Delage, F.; Advocat, T.; Vernaz, E.; Crovisier, J.L.

1991-01-01

Interactions results of the borosilicate glass used in radioactive wastes confinement and aqueous solutions at various temperature and PH show that for the glass components: - the release rate evolution follows an Arrhenius law, - in acid PH, there is a selective dissolution, - in basic PH, there is a stoechiometric dissolution [fr

Calculation of separation selectivity of aqueous electrolytic solutions with reverse osmosis membranes

International Nuclear Information System (INIS)

Ognevskij, A.V.; Fomichev, S.V.; Khvostov, V.F.; Kochergin, N.V.; AN SSSR, Moscow

1988-01-01

Viscosity and dielectric permittivity of a bound water layer in micropores of cellulose acetate membranes used for electrolyte ion separation by reverse osmosis method are calculated using the water cluster model and the proposed structural temperature parameter. Based on the model representations presented an algorithmof reverse osmosis membrane selectivity calculation in diluted aqueous solutions ofelectrolytes containing Cs + , Sr 2+ , I - and other ions is constructed

Study on corrosion of carbon steel in DEA aqueous solutions

Science.gov (United States)

Yang, Jun Han; Xie, Jia Lin; Zhang, Li

2018-02-01

Corrosion of carbon steel in the CO2 capture process using diethanolamine (DEA) aqueous solutions was investigated. The effects of the mass concentrations of DEA, solution temperature and CO2 loading on the corrosion rate of carbon steel were demonstrated. The experimental results provided comprehensive information on the appropriate concentration range of DEA aqueous solutions under which low corrosion of carbon steel can be achieved.

Templated self-assembly of quantum dots from aqueous solution using protein scaffolds

Energy Technology Data Exchange (ETDEWEB)

Blum, Amy Szuchmacher [Center for Bio/Molecular Science and Engineering, Naval Research Laboratory, 4555 Overlook Avenue SW, Washington, DC 20375 (United States); Soto, Carissa M [Center for Bio/Molecular Science and Engineering, Naval Research Laboratory, 4555 Overlook Avenue SW, Washington, DC 20375 (United States); Wilson, Charmaine D [Geo-Centers, Incorporated, Newton, MA 02459 (United States); Whitley, Jessica L [Geo-Centers, Incorporated, Newton, MA 02459 (United States); Moore, Martin H [Center for Bio/Molecular Science and Engineering, Naval Research Laboratory, 4555 Overlook Avenue SW, Washington, DC 20375 (United States); Sapsford, Kim E [George Mason University, 10910 University Boulevard, Manassas, VA 20110 (United States); Lin, Tianwei [Department of Molecular Biology, The Scripps Research Institute, 10550 North Torrey Pines Road, La Jolla, CA 92037 (United States); Chatterji, Anju [Department of Molecular Biology, The Scripps Research Institute, 10550 North Torrey Pines Road, La Jolla, CA 92037 (United States); Johnson, John E [Department of Molecular Biology, The Scripps Research Institute, 10550 North Torrey Pines Road, La Jolla, CA 92037 (United States); Ratna, Banahalli R [Center for Bio/Molecular Science and Engineering, Naval Research Laboratory, 4555 Overlook Avenue SW, Washington, DC 20375 (United States)

2006-10-28

Short, histidine-containing peptides can be conjugated to lysine-containing protein scaffolds to controllably attach quantum dots (QDs) to the scaffold, allowing for generic attachment of quantum dots to any protein without the use of specially engineered domains. This technique was used to bind quantum dots from aqueous solution to both chicken IgG and cowpea mosaic virus (CPMV), a 30 nm viral particle. These quantum dot-protein assemblies were studied in detail. The IgG-QD complexes were shown to retain binding specificity to their antigen after modification. The CPMV-QD complexes have a local concentration of quantum dots greater than 3000 nmol ml{sup -1}, and show a 15% increase in fluorescence quantum yield over free quantum dots in solution.

Investigation of ionizing radiation effect on albumin aqueous solutions

International Nuclear Information System (INIS)

Sizikov, A.M.; Adeeva, L.N.; Ogryzkova, I.F.

1986-01-01

Gamma radiation effect on 0.1-0.5%-albumin aqueous solutions has been investigated; variations of viscosity and optical density of solutions at pH medium different values and completeness of protein separation owing to radiation coagulation have been determined. It is shown that due to radiation coagulation it is possible to quantitatively separate albumin from irradiated aqueous solutions. The albumin coagulation is caused by OH radicals the action of which on albumin macromolecules results in destruction of intramolecular bonds and albumin conformation transformations

Partial molar volumes and viscosities of aqueous hippuric acid solutions containing LiCl and MnCl2 · 4H2O at 303.15 K

Science.gov (United States)

Deosarkar, S. D.; Tawde, P. D.; Zinjade, A. B.; Shaikh, A. I.

2015-09-01

Density (ρ) and viscosity (η) of aqueous hippuric acid (HA) solutions containing LiCl and MnCl2 · 4H2O have been studied at 303.15 K in order to understand volumetric and viscometric behavior of these systems. Apparent molar volume (φv) of salts were calculated from density data and fitted to Massons relation and partial molar volumes (φ{v/0}) at infinite dilution were determined. Relative viscosity data has been used to determine viscosity A and B coefficients using Jones-Dole relation. Partial molar volume and viscosity coefficients have been discussed in terms of ion-solvent interactions and overall structural fittings in solution.

Predicting accurate absolute binding energies in aqueous solution

DEFF Research Database (Denmark)

Jensen, Jan Halborg

2015-01-01

Recent predictions of absolute binding free energies of host-guest complexes in aqueous solution using electronic structure theory have been encouraging for some systems, while other systems remain problematic. In this paper I summarize some of the many factors that could easily contribute 1-3 kcal......-represented by continuum models. While I focus on binding free energies in aqueous solution the approach also applies (with minor adjustments) to any free energy difference such as conformational or reaction free energy differences or activation free energies in any solvent....

Synthesis of (Cr,V){sub 2}(C,N) solid solution powders by thermal processing precursors

Energy Technology Data Exchange (ETDEWEB)

Liu, Anrui [School of Materials Science & Engineering, Sichuan University, Chengdu, 610065 (China); Liu, Ying [School of Materials Science & Engineering, Sichuan University, Chengdu, 610065 (China); Key Laboratory of Advanced Special Material & Technology, Ministry of Education, Chengdu, 610065 (China); Ma, Shiqing; Qiu, Yuchong; Rong, Pengcheng; Ye, Jinwen [School of Materials Science & Engineering, Sichuan University, Chengdu, 610065 (China)

2017-06-01

The single-phase (Cr,V){sub 2}(C,N) solid solution powders were fabricated via carbothermal reduction-nitridation (CRN) processing technique. The effects of heat treatment temperature, nitrogen pressure and carbon proportion were experimentally studied in detail by X-ray Diffraction (XRD), Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and thermal analysis. The chemical transformations of vanadium and chromium compounds were as follows: precursors → V{sub 2}O{sub 3}, Cr{sub 2}O{sub 3} → Cr{sub 3}C{sub 2}, Cr{sub 2}O{sub 3}, (Cr,V){sub 2}(C,N) → (Cr,V){sub 2}(C,N). When the heat-treated temperature was below 1200 °C, chromium oxides didn’t completely react. However, higher temperature ∼1300 °C could not only lead to the segregation of some nitrides and carbon black, but also to the occurrence of fiber-bridged particles. The system nitrogen pressure over 0.03 MPa would cause a subtle transformation of (Cr,V){sub 2}(C,N) to VCrN{sub 2}. When the carbon proportion was below 15 wt%, the oxides could not be completely reduced, while when the carbon proportion was above 15.5 wt%, some undesired carbides, like Cr{sub 23}C{sub 6} and Cr{sub 3}C{sub 2}, would form. Ultimately, the homogeneously distributed pure-phase (Cr,V){sub 2}(C,N) spherical particles with the average size of ∼1.5 μm were obtained at the optimal conditions of the treatment of precursors at 1200 °C for 1 h with the nitrogen pressure of 0.03 MPa and carbon content of 15.5 wt%. The chemical composition of the solid solution with the optimal process could be drawn as (Cr{sub 0.85}V{sub 0.15}){sub 2}(C{sub 0.57}N{sub 0.43}). Thermal processing precursors method shows the advantages of lower synthesis temperature, shorter period and finer particles when comparing with the conventional preparations. - Highlights: • Single phase of (Cr,V){sub 2}(C,N) powders were synthesized for the first time. • Precursors were used to prepared the powders by carbothermal

Reactor coolant system and containment aqueous chemistry

International Nuclear Information System (INIS)

Torgerson, D.F.

1986-01-01

Fission products released from fuel during reactor accidents can be subject to a variety of environments that will affect their ultimate behavior. In the reactor coolant system (RCS), for example, neutral or reducing steam conditions, radiation, and surfaces could all have an effect on fission product retention and chemistry. Furthermore, if water is encountered in the RCS, the high temperature aqueous chemistry of fission products must be assessed to determine the quantity and chemical form of fission products released to the containment building. In the containment building, aqueous chemistry will determine the longer-term release of volatile fission products to the containment atmosphere. Over the past few years, the principles of physical chemistry have been rigorously applied to the various chemical conditions described above. This paper reviews the current state of knowledge and discusses the future directions of chemistry research relating to the behavior of fission products in the RCS and containment

Heterobimetallic [NiFe] Complexes Containing Mixed CO/CN- Ligands: Analogs of the Active Site of the [NiFe] Hydrogenases.

Science.gov (United States)

Perotto, Carlo U; Sodipo, Charlene L; Jones, Graham J; Tidey, Jeremiah P; Blake, Alexander J; Lewis, William; Davies, E Stephen; McMaster, Jonathan; Schröder, Martin

2018-03-05

The development of synthetic analogs of the active sites of [NiFe] hydrogenases remains challenging, and, in spite of the number of complexes featuring a [NiFe] center, those featuring CO and CN - ligands at the Fe center are under-represented. We report herein the synthesis of three bimetallic [NiFe] complexes [Ni( N 2 S 2 )Fe(CO) 2 (CN) 2 ], [Ni( S 4 )Fe(CO) 2 (CN) 2 ], and [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] that each contain a Ni center that bridges through two thiolato S donors to a {Fe(CO) 2 (CN) 2 } unit. X-ray crystallographic studies on [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ], supported by DFT calculations, are consistent with a solid-state structure containing distinct molecules in the singlet ( S = 0) and triplet ( S = 1) states. Each cluster exhibits irreversible reduction processes between -1.45 and -1.67 V vs Fc + /Fc and [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] possesses a reversible oxidation process at 0.17 V vs Fc + /Fc. Spectroelectrochemical infrared (IR) and electron paramagnetic resonance (EPR) studies, supported by density functional theory (DFT) calculations, are consistent with a Ni III Fe II formulation for [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + . The singly occupied molecular orbital (SOMO) in [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + is based on Ni 3d z 2 and 3p S with the S contributions deriving principally from the apical S-donor. The nature of the SOMO corresponds to that proposed for the Ni-C state of the [NiFe] hydrogenases for which a Ni III Fe II formulation has also been proposed. A comparison of the experimental structures, and the electrochemical and spectroscopic properties of [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] and its [Ni( N 2 S 3 )] precursor, together with calculations on the oxidized [Ni( N 2 S 3 )Fe(CO) 2 (CN) 2 ] + and [Ni( N 2 S 3 )] + forms suggests that the binding of the {Fe(CO)(CN) 2 } unit to the {Ni(CysS) 4 } center at the active site of the [NiFe] hydrogenases suppresses thiolate-based oxidative chemistry involving the bridging thiolate S donors

Thermophysical Properties of Aqueous Solutions Used as Secondary Working Fluids

OpenAIRE

Melinder, Åke

2007-01-01

Secondary working fluids (secondary refrigerants, heat transfer fluids, antifreezes, brines) have long been used in various indirect re-frigeration and heat pump systems. Aqueous solutions (water solu-tions) have long been used as single phase (liquid only) secondary working fluids for cooling in supermarkets, ice rinks, heat recovery systems, heat pumps and other applications. However, aqueous solutions are increasingly used also for freezers in supermarkets and other applications in low tem...

Measuring and modeling aqueous electrolyte/amino-acid solutions with ePC-SAFT

International Nuclear Information System (INIS)

Held, Christoph; Reschke, Thomas; Müller, Rainer; Kunz, Werner; Sadowski, Gabriele

2014-01-01

Highlights: • Amino-acid solubilities and osmotic coefficients in ternary solutions containing one amino acids and one salt measured. • Weak salt influence on amino-acid solubilities except for salts containing Mg [2+] or NO 3 [−] (salting-in behavior). • Osmotic coefficients dominated by the solute with the highest molality. • Amino-acid solubilities and osmotic coefficients predicted reasonably with ePC-SAFT with deviations of 3.7% and 9.3%. • Predictions based on pure-component parameters for ions and amino acids using no ion/amino-acid fitting parameters. -- Abstract: In this work thermodynamic properties of electrolyte/amino acid/water solutions were measured and modeled. Osmotic coefficients at 298.15 K were measured by means of vapor-pressure osmometry. Amino-acid solubility at 298.15 K was determined gravimetrically. Considered aqueous systems contained one of the four amino acids: glycine, L-/DL-alanine, L-/DL-valine, and L-proline up to the respective amino-acid solubility limit and one of 13 salts composed of the ions Li + , Na + , K + , NH 4 + , Cl − , Br − , I − , NO 3 − , and SO 4 2− at salt molalities of 0.5, 1.0, and 3.0 mol · kg −1 , respectively. The data show that the salt influence is more pronounced on osmotic coefficients than on amino-acid solubility. The electrolyte Perturbed-Chain Statistical Association Theory (ePC-SAFT) was applied to model thermodynamic properties in aqueous electrolyte/amino-acid solutions. In previous works, this model had been applied to binary salt/water and binary amino acid/water systems. Without fitting any additional parameters, osmotic coefficients and amino-acid solubility in the ternary electrolyte/amino acid/water systems could be predicted with overall deviations of 3.7% and 9.3%, respectively, compared to the experimental data

A thermodynamic model for aqueous solutions of liquid-like density

Energy Technology Data Exchange (ETDEWEB)

Pitzer, K.S.

1987-06-01

The paper describes a model for the prediction of the thermodynamic properties of multicomponent aqueous solutions and discusses its applications. The model was initially developed for solutions near room temperature, but has been found to be applicable to aqueous systems up to 300/sup 0/C or slightly higher. A liquid-like density and relatively small compressibility are assumed. A typical application is the prediction of the equilibrium between an aqueous phase (brine) and one or more solid phases (minerals). (ACR)

Sensitivity of technetium-99m-d,1-HMPAO to radiolysis in aqueous solutions

International Nuclear Information System (INIS)

Tubergen, K.; Corlija, M.; Volkert, W.A.; Holmes, R.A.

1991-01-01

The sensitivity of technetium-99m- (99mTc) d,l-HMPAO to radiolytically induced dissociation in aqueous solutions was investigated. It was found that cobalt-60 (60Co) gamma irradiation of solutions containing 99mTc-d,l-HMPAO with only 1600 cGy reduced the lipophilic chelates' radiochemical purity (RCP) to 50%-60%. The radiolytic sensitivity of 99mTc-meso-HMPAO is significantly lower. The results indicate that radiolytically produced intermediates limit the in vitro stability of 99mTc-d,l-HMPAO

Antimony removal from aqueous solutions using Zirconium hydroxide

International Nuclear Information System (INIS)

Petrescu, D.; Velciu, L.; Bucur, C.

2016-01-01

In this paper it is presented an experimental test for non-radioactive antimony removal from aqueous solutions using zirconium hydroxide powder. Also, it was studied how the temperature and pH influences antimony adsorption onto zirconium hydroxide surface. After the adsorption, solutions were filtered on Cellulose Mixed Ester Membrane with 0.2 μm pore size to remove the zirconium powder and then the aqueous solutions were sent to Inductively Coupled Plasma Optic Emission Spectrometry (ICP-OES) for quantitative analysis of Sb. Zirconium hydroxide powders were examined by optical microscopy. For the solutions that were tested at pH 4.5 and 10.2 the antimony concentration dropped below the detection limit of ICP-OES device, proof of antimony adsorption on zirconium hydroxide. Also, for the other tested solutions which had pH=12 the antimony concentration reduced with 77% and 80%. The temperature had no influence upon adsorption mechanism. (authors)

Preparation of metallic nanoparticles by irradiation in starch aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Nemţanu, Monica R., E-mail: monica.nemtanu@inflpr.ro; Braşoveanu, Mirela, E-mail: monica.nemtanu@inflpr.ro; Iacob, Nicuşor, E-mail: monica.nemtanu@inflpr.ro [National Institute for Lasers, Plasma and Radiation Physics, Electron Accelerators Laboratory, 409 Atomiştilor St., PO Box MG-36, 077125, Bucharest-Măgurele (Romania)

2014-11-24

Colloidal silver nanoparticles (AgNPs) were synthesized in a single step by electron beam irradiation reduction of silver ions in aqueous solution containing starch. The nanoparticles were characterized by spectrophotocolorimetry and compared with those obtained by chemical (thermal) reduction method. The results showed that the smaller sizes of AgNPs were prepared with higher yields as the irradiation dose increased. The broadening of particle size distribution occurred by increasing of irradiation dose and dose rate. Chromatic parameters such as b* (yellow-blue coordinate), C* (chroma) and ΔE{sub ab} (total color difference) could characterize the nanoparticles with respect of their concentration. Hue angle h{sup o} was correlated to the particle size distribution. Experimental data of the irradiated samples were also subjected to factor analysis using principal component extraction and varimax rotation in order to reveal the relation between dependent variables and independent variables and to reduce their number. The radiation-based method provided silver nanoparticles with higher concentration and narrower size distribution than those produced by chemical reduction method. Therefore, the electron beam irradiation is effective for preparation of silver nanoparticles using starch aqueous solution as dispersion medium.

Status of determining transuranic nuclides speciation in aqueous solution with laser spectrometry

International Nuclear Information System (INIS)

Wang Bo; Liu Dejun; Yao Jun; Chen Xi; Long Haoqi; Zeng Jishu; Su Xiguang; Fan Xianhua

2007-01-01

The knowledge about speciation of transuranic nuclides in aqueous solution is a basis for understanding the chemical and migration behavior of transuranic nuclides in aqueous solution. The speciation of transuranic nuclides with trace concentration is complicated in near neutral aqueous solutions, including change of oxidation state, complexation and colloid generation, etc. The concentrations of transuranium in near neutral aqueous solution usually below the sensitivity range of method such as conventional absorption spectroscopy. The radioactive analysis method has a very low detection limits for radionuclides, however, it wouldn' t allow the direct measurement of the transuranic species. In contrast with these methods, laser spectroscopy is an ideal method with high sensitivity, and non-contact and non-destructive for determining the speciation of transuranic nuclides. This paper summarizes the status and application of LIPAS (Laser-induced Photoacoustic Spectrometry), LIBD (Laser-induced Breakdown Detection) and TRLFS (Time-resolved Laser Fluorescence Spectrometry) to determine the speciation of transuranic nuclides with trace concentration in aqueous solutions. (authors)

Process for the recovery of alkali metal salts from aqueous solutions thereof

International Nuclear Information System (INIS)

Vitner, J.

1984-01-01

In an integrated process for the recovery of alkakli metal phenates and carboxylates from aqueous solutions thereof, the aqueous solution is spray dried and the drying gas stream is contacted with an aqueous alkali metal salt solution which dissolves the particles of the alkali metal salt that were entrained in the drying gas stream. The salt-free inert gas stream is then dried, heated, and returned to the spray dryer

Grafted wood pulp containing quaternary ammonium group and its application in the removal of different anions from aqueous solution

International Nuclear Information System (INIS)

Sokker, H.H.

2005-01-01

Network wood pulp based on acrylonitrile has been chemically modified through different reactions to obtain group capable of anion exchange. Graft copolymerization of acrylonitrile onto wood pulp was carried out by using gamma-radiation 60 Co. Factors affecting the grafting process e.g radiation dose and monomer concentration were investigated.The chemical modification of cyano groups were carried out by reaction with ethanol amine producing oxazoline group followed by quaternization of tertiary amine by reaction with benzyl chloride producing quaternary ammonium salt. The grafted and modified wood pulp were characterized by FTIR, SEM and TGA.Qualitative experiments of adsorption were conducted to evaluate the modified wood pulp on fixing sulfate, phosphate,nitrate and dichromate from aqueous solution using batch extractions. Based on the results obtained, it may be concluded that it is possible to modify chemically wood pulp containing cyano groups by different routes for its usage as anion exchanger

Memory effect of calcined layered samarium hydroxy chlorides in aqueous solution

International Nuclear Information System (INIS)

Lee, Byung Il; Byeon, Song Ho

2015-01-01

The decomposition and recovery behavior of layered samarium hydroxychloride (Sm 2 (OH) 5 Cl·nH 2 O, LSmH) has been closely studied in various conditions. Although the heat treatment of LSmH at 700 °C completely collapsed typical layered structure, the calcined LSmH (c-LSmH) recovered its layered characteristics and consequently its ability to intercalate anions into the interlayer space when it was rehydroxylated and rehydrated in aqueous solutions containing organic and inorganic anions. This phenomenon is similar to the memory effect observed in classical layered double hydroxides (LDHs), where LDHs calcined to a mixture of metal oxides can recover their layered structures in aqueous solutions. In contrast, the recovery reaction of c-LSmH in water without any counter anions was unsuccessful and instead resulted in the formation of Sm(OH) 3 . Such a difference was interpreted on the basis of the salt effect on Sm 2 (OH) 5 Cl·nH 2 O–Sm(OH) 3 phase equilibria in water

Dissolution of lignin in green urea aqueous solution

Science.gov (United States)

Wang, Jingyu; Li, Ying; Qiu, Xueqing; Liu, Di; Yang, Dongjie; Liu, Weifeng; Qian, Yong

2017-12-01

The dissolution problem is the main obstacle for the value-added modification and depolymerization of industrial lignin. Here, a green urea aqueous solution for complete dissolution of various lignin is presented and the dissolution mechanism is analyzed by AFM, DLS and NMR. The results show that the molecular interaction of lignin decreases from 32.3 mN/m in pure water to 11.3 mN/m in urea aqueous solution. The immobility of 1H NMR spectra and the shift of 17O NMR spectra of urea in different lignin/urea solutions indicate that the oxygen of carbonyl in urea and the hydrogen of hydroxyl in lignin form new hydrogen bonds and break the original hydrogen bonds among lignin molecules. The shift of 1H NMR spectra of lignin and the decrease of interactions in model compound polystyrene indicate that urea also breaks the π-π interactions between aromatic rings of lignin. Lignin dissolved in urea aqueous has good antioxidant activity and it can scavenge at least 63% free radicals in 16 min.

Solubility of hydrogen in aqueous solutions of sodium and potassium bicarbonate from 293 to 333 K

NARCIS (Netherlands)

Engel, D.C.; Engel, D.C.; Versteeg, Geert; van Swaaij, Willibrordus Petrus Maria

1996-01-01

An experimental study is presented of the hydrogen solubility in aqueous salt solutions containing sodium and potassium bicarbonate from 293 to 333 K. For this purpose, gas consumption measurements have been performed by determining the ultimate pressure decrease in an intensively stirred, high

Solubility of Hydrogen in Aqueous Solutions of Sodium and Potassium Bicarbonate from 293 to 333 K

NARCIS (Netherlands)

Engel, Dico C.; Versteeg, Geert F.; Swaaij, Wim P.M. van

1996-01-01

An experimental study is presented of the hydrogen solubility in aqueous salt solutions containing sodium and potassium bicarbonate from 293 to 333 K. For this purpose, gas consumption measurements have been performed by determining the ultimate pressure decrease in an intensively stirred, high

LASERS, ACTIVE MEDIA: The aqueous-polyelectrolyte dye solution as an active laser medium

Science.gov (United States)

Akimov, A. I.; Saletskii, A. M.

2000-11-01

The spectral, luminescent, and lasing properties of aqueous solutions of a cationic dye rhodamine 6G with additions of anion polyelectrolytes — polyacrylic and polymethacrylic acids — are studied. It is found that the energy and spectral properties of lasing of these solutions depend on the ratio of concentrations of polyelectrolyte and molecules. It is also found that the lasing parameters of aqueous-polyelectrolyte dye solutions can be controlled by changing the structure of the molecular system. The variation in the structure of aqueous-polyelectrolyte dye solutions of rhodamine 6G resulted in an almost five-fold increase in the lasing efficiency compared to that in aqueous dye solutions.

Electrodialysis potential for fractionation of multicomponent aqueous solutions

Science.gov (United States)

Grzegorzek, Martyna; Majewska-Nowak, Katarzyna

2017-11-01

The paper aimed at the evaluation of the batch electrodialysis (ED) run in the course of treatment and desalination of various aqueous mixtures containing both mineral (sodium fluoride, sodium chloride) and organic substances (dyes or humic acids). The commercial ED stack (PCCell Bed) equipped with standard anion-exchange and cation-exchange membranes or monovalent selective anion-exchange membranes was used. The ED experiments were performed at a constant current density (1.56 or 1.72 mA/cm2). The mechanism of ion migration as well as membrane deposition for variable solution composition and various membrane types was analyzed The calculated mass balance and electrical energy demand for each ED run were helpful in evaluating the membrane fouling intensity. It was found that the presence of organic substances in the treated solution had a minor impact on energy consumption, but rather strongly affected chloride flux. The extent of organics deposition was significantly lower for monovalent selective anion-exchange membranes than for classic anion-exchange membranes.

Method for Non-Invasive Determination of Chemical Properties of Aqueous Solutions

Science.gov (United States)

Todd, Paul W. (Inventor); Jones, Alan (Inventor); Thomas, Nathan A. (Inventor)

2016-01-01

A method for non-invasively determining a chemical property of an aqueous solution is provided. The method provides the steps of providing a colored solute having a light absorbance spectrum and transmitting light through the colored solute at two different wavelengths. The method further provides the steps of measuring light absorbance of the colored solute at the two different transmitted light wavelengths, and comparing the light absorbance of the colored solute at the two different wavelengths to determine a chemical property of an aqueous solution.

Comparative radiosensitivity of amino acids during γ-radiolysis in aqueous solutions

International Nuclear Information System (INIS)

Duzhenkova, N.A.; Savich, A.V.

1977-01-01

The radiosensitivity of amino acids contained in proteins has been compared. The γ-radiolysis of aqueous solutions of amino acids has studied over a wide range of concentrations in the presence of air, the dose rate being 60 rad/sec, and the dose, 100 krad. Radiation-chemical yields of amino acid decay and ammonia accumulation are given. An increase in yields with amino acid concentration has been established. Assumptions concerning some peculiarities of the amino acid decay mechanism are made

γ-Irradiation-induced radiolysis of inulin in aqueous solutions

International Nuclear Information System (INIS)

Tsyba, I.A.; Revina, A.A.; Shostenko, A.G.

1997-01-01

Radiochemical transformations of inulin in aqueous solutions, in air, in the presence of inert gases, helium, nitrogen and in nitrous oxide exposed to various doses of 60 Co γ-irradiation were investigated. It was shown that interactions in inulin with OH radicals are principally responsible for radiolytic decomposition of inulin. The data on radiolysis of more simple model systems were used to make available decomposition spectra of γ-irradiated aerated aqueous solution of inulin. 9 refs., 6 figs

Degradation of amoxicillin, ampicillin and cloxacillin antibiotics in aqueous solution by the UV/ZnO photocatalytic process

International Nuclear Information System (INIS)

Elmolla, Emad S.; Chaudhuri, Malay

2010-01-01

The study examined the effect of operating conditions (zinc oxide concentration, pH and irradiation time) of the UV/ZnO photocatalytic process on degradation of amoxicillin, ampicillin and cloxacillin in aqueous solution. pH has a great effect on amoxicillin, ampicillin and cloxacillin degradation. The optimum operating conditions for complete degradation of antibiotics in an aqueous solution containing 104, 105 and 103 mg/L amoxicillin, ampicillin and cloxacillin, respectively were: zinc oxide 0.5 g/L, irradiation time 180 min and pH 11. Under optimum operating conditions, complete degradation of amoxicillin, ampicillin and cloxacillin occurred and COD and DOC removal were 23.9 and 9.7%, respectively. The photocatalytic reactions under optimum conditions approximately followed a pseudo-first order kinetics with rate constant (k) 0.018, 0.015 and 0.029 min -1 for amoxicillin, ampicillin and cloxacillin, respectively. UV/ZnO photocatalysis can be used for amoxicillin, ampicillin and cloxacillin degradation in aqueous solution.

Prediction of scale potential in ethylene glycol containing solutions

Energy Technology Data Exchange (ETDEWEB)

Sandengen, Kristian; Oestvold, Terje

2006-03-15

This work presents a method for scale prediction in MEG (Mono Ethylene Glycol / 1,2-ethane-diol) containing solutions. It is based on an existing PVT scale model using a Pitzer ion interaction model for the aqueous phase. The model is well suited for scale prediction in saline solutions, where the PVT part is necessary for calculating CO{sub 2} phase equilibria being critical for carbonate scale. MEG influences the equilibria contained in the model, and its effect has been added empirically. Thus the accuracy of the model is limited by the amount of available experimental data. The model is applicable in the range 0-99wt% MEG and includes a wide variety of salts. In addition to the aspects of scale modelling in MEG+water solutions, this work presents new experimental data on CaSO4 solubility (0-95wt% MEG and 22-80 deg.C). CaSO4 solubility is greatly reduced by MEG to an extent that ''Salting-out'' is possible. (author) (tk)

Process for the removal of radium from acidic solutions containing same

Science.gov (United States)

Scheitlin, F.M.

The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of /sup 226/Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

Speciation analysis on Eu(3) in aqueous solution using laser-induced breakdown spectroscopy

International Nuclear Information System (INIS)

Hotokezaka, H.; Tanaka, S.; Nagasaki, S.

2001-01-01

Investigation of the chemical behaviour of lanthanides and actinides in the geosphere is important for the safety assessment of high-level radioactive waste disposal. However, determination of speciation for lanthanides and actinides is difficult, because it is too hard to distinguish between metal ion and colloidal metal in aqueous solution. Laser-induced breakdown spectroscopy (LIBS) can detect both ions and microparticles of metals in aqueous solution, especially, high sensitive to microparticles. In this study, we analysed Eu(III) ion and Eu 2 O 3 particle in aqueous solution by LIBS, and measured the hydrolysis behaviour of Eu(III) in aqueous solution. Furthermore, we tried to detect the plasma emission of Eu(III) ions sorbed on TiO 2 particles, and also tried to observe the adsorption behaviour of Eu(III) ions onto TiO 2 particles in aqueous solution. (authors)

[Enhancement effect of double-beam laser processed aqueous solution on ICP emission spectrum].

Science.gov (United States)

Chen, Jin-zhong; Xu, Li-jing; Su, Hong-xin; Li, Xu; Wang, Shu-fang

2015-01-01

In order to change the physical properties of aqueous solution and improve the radiation intensity of the ICP emission spectrum, the effects of different laser power density and irradiation time on the surface tension and viscosity of aqueous solution were investigated by using near infrared laser at 976 nm and CO2 laser at 10. 6 µm to irradiate aqueous solution orthogonally, then the enhancement of ICP spectral intensity with processed solution was discussed. The results showed that the surface tension and viscosity of aqueous solution reduced by 42. 13% and 14. 03% compared with the untreated, and the atomization efficiency increased by 51.26% at the laser power density 0. 265 7 W . cm-2 of 976 nm and 0. 206 9 W . cm-2 of CO2 laser with 40 min irradiation time. With the optimized aqueous solution introduced into the ICP source, the spectral line intensity of sample elements As, Cd, Cr, Hg and Pb was enhanced by 46.29%, 94. 65%, 30. 76%, 33.07% and 94. 58% compared to the untreated aqueous solution, while the signal-to-background ratio increased by 43. 84%, 85. 35%, 28. 71%, 34. 37% and 90. 91%, respectively. Plasma temperature and electron density also increased by 5. 94% and 1. 18% respectively. It is obvious that the method of double-beam laser orthogonal irradiation on solution can reduce the surface tension and viscosity of aqueous solution significantly, and raise the radiationintensity of ICP source, and will provide a better condition for detecting the trace heavy metal elements in water samples.

Solar photo-Fenton mineralization of antipyrine in aqueous solution.

Science.gov (United States)

Durán, A; Monteagudo, J M; Sanmartín, I; Carrasco, A

2013-11-30

The mineralization of an aqueous solution of antipyrine (C11H12N2O), an emerging contaminant, using a solar photocatalytic oxidation process assisted with ferrioxalate was evaluated in a compound parabolic collector (CPC) pilot plant. Under the selected operating conditions ([H2O2] = 250 ppm, [Fe] = 14 ppm, pH = 2.7, and [(COOH)2·2H2O] = 80 ppm), 60% of TOC is removed just 5 min after treating an aqueous solution containing 50 ppm of antipyrine. The addition of oxalic acid up to a maximum concentration of 80 ppm significantly increases the mineralization rate during the first 15 min of the reaction. The synergism between the solar and dark H2O2/ferrioxalate process was quantified at 79%, calculated from the pseudo first-order mineralization rate constants. The operational costs due to the consumption of electrical energy, reagents and catalysts were calculated from the optimal conditions and compared with a novel sono-photocatalytic process using artificial UV-light. The results showed that the ferrioxalate-assisted solar photo-Fenton process was economically feasible, being able to achieve up to 60% mineralization with a total cost of 4.5 cent €/g TOC removed (1.1 €/m(3)). Copyright © 2013 Elsevier Ltd. All rights reserved.

Radiation-induced degradation of chlorophenols in aqueous solution

International Nuclear Information System (INIS)

Hu Jun; Wang Jianlong

2005-01-01

Radiation processing is a promising technology for applications in environmental protection, which includes wastewater treatment, micro-polluted drinking water treatment and the treatment of industrial wastewater containing various toxic and nonbiodegradable pollutants, municipal sewage and sludge disinfection, and flue gas desulfuration, etc. The paper reviews manly the recent progresses in radiolysis of chlorinated phenols in aqueous solution. Advantages and existing problems of the method in this particular application ar discussed. Mechanisms of radiation-induced degradation of chlorophenols, and the factors affecting the degradation efficiency, are discussed, too. It is concluded that combined approaches, such ozone oxidation and other methods, are of great help to the radiation processing application, in terms of lowering down the dose and increasing the efficient of pollutant removal. (authors)

Supercooling of aqueous dimethylsulfoxide solution at normal and high pressures: Evidence for the coexistence of phase-separated aqueous dimethylsulfoxide solutions of different water structures

Science.gov (United States)

Kanno, H.; Kajiwara, K.; Miyata, K.

2010-05-01

Supercooling behavior of aqueous dimethylsulfoxide (DMSO) solution was investigated as a function of DMSO concentration and at high pressures. A linear relationship was observed for TH (homogeneous ice nucleation temperature) and Tm (melting temperature) for the supercooling of aqueous DMSO solution at normal pressure. Analysis of the DTA (differential thermal analysis) traces for homogeneous ice crystallization in the bottom region of the TH curve for a DMSO solution of R =20 (R: moles of water/moles of DMSO) at high pressures supported the contention that the second critical point (SCP) of liquid water should exist at Pc2=˜200 MPa and at Tc2pressure of SCP, Tc2: temperature of SCP). The presence of two TH peaks for DMSO solutions (R =15, 12, and 10) suggests that phase separation occurs in aqueous DMSO solution (R ≤15) at high pressures and low temperatures (pressure dependence of the two TH curves for DMSO solutions of R =10 and 12 indicates that the two phase-separated components in the DMSO solution of R =10 have different liquid water structures [LDL-like and HDL-like structures (LDL: low-density liquid water, HDL: high-density liquid water)] in the pressure range of 120-230 MPa.

Self-aggregation of liquids from biomass in aqueous solution

International Nuclear Information System (INIS)

Lomba, Laura; Giner, Beatriz; Zuriaga, Estefanía; Moya, Juana; Lafuente, Carlos

2013-01-01

Highlights: • Aggregation behaviour of liquids from biomass in aqueous solution has been studied. • Standard Gibbs free energies of aggregation have been calculated. • Solubility in water of these compounds has been determined. • Critical aggregation concentration decreases as the solubility in water does. -- Abstract: Aggregation of several chemicals from biomass: furfural derived compounds (furfural, 5-methylfurfural, furfuryl alcohol and tetrahydrofurfuryl alcohol), lactate derived compounds (methyl lactate, ethyl lactate and butyl lactate), acrylate derived compound (methyl acrylate) and levulinate compounds (methyl levulinate, ethyl levulinate and butyl levulinate) in aqueous solution has been characterised at T = 298.15 K through density, ρ, speed of sound, u, and isentropic compressibilities, κ S , measurements. In addition the standard Gibbs free energies of aggregation have been also calculated. Furthermore, in order to deepen insight the behaviour of these chemicals in aqueous solution, the solubility of these compounds has been measured at T = 298.15 K

Zeolites as alcohol adsorbents from aqueous solutions

Directory of Open Access Journals (Sweden)

Cekova Blagica

2006-01-01

Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

Volumetric properties of itaconic acid aqueous solutions

International Nuclear Information System (INIS)

Nisenbaum, Alexander; Apelblat, Alexander; Manzurola, Emanuel

2012-01-01

Highlights: ► Densities of itaconic acid aqueous solutions in a wide range of concentrations and temperatures. ► The apparent molar volumes and the cubic expansion coefficients. ► The derivatives of isobaric heat capacities with respect to pressure. ► Changes in the structure of water when itaconic acid is dissolved. - Abstract: Densities of itaconic acid aqueous solutions were measured at 5 K intervals from T = (278.15 to 343.15) K. From the determined densities, the apparent molar volumes, the cubic expansion coefficients and the second derivatives of volume with respect to temperature which are interrelated with the derivatives of isobaric heat capacities with respect to pressure were evaluated. These derivatives were qualitatively correlated with the changes in the structure of water when itaconic acid is dissolved in it.

Radiation chemistry of aqueous solutions of acetonitrile and propionitrile

International Nuclear Information System (INIS)

Shushtarian, M.J.

1975-01-01

The radiation chemistry of water and aqueous solutions is a branch of radiation chemistry dealing with chemical changes in water and aqueous solutions induced by high energy radiations. High energy radiations of interest in radiation chemistry are short-wave electromagnetic radiations (X- and γ-rays) and fast charged particles (α- and β-particles, electrons, deuterons and fission fragments). The energy of the particles and photons bringing about chemical reactions in the field of modern radiation chemistry is much higher than that of photons causing photochemical reactions

Radiolysis of Aqueous Toluene Solutions

International Nuclear Information System (INIS)

Christensen, H.C.; Gustafson, R.

1971-04-01

Aqueous toluene solutions have been irradiated with Co γ-rays. In unbuffered solutions the various cresol isomers are formed in a total yield of 0.45, 0.87 and 0.94 molecules/100 eV absorbed energy in argon-, N 2 O- and air - saturated solutions, respectively. The yields are reduced in acid (pH 3) solutions (G 0.14, 0.14 and 0.52, respectively) but the reduction is compensated by the formation of 1,2-di-phenylethane in yields of 0.49 and 1.60 in argon- and N 2 O-saturated solutions, respectively. Benzyl radicals are formed through an acid catalysed water elimination reaction from the initially formed hydroxymethylcyclohexadienyl radical. Phenyltolylmethanes, dimethylbiphenyls and partly reduced dimers are also formed during the radiolysis. Hydrogen is formed in the same yield as the molecular yield, g(H 2 ). Xylene isomers and benzene are formed in trace quantities. The most remarkable effects of the addition of Fe(III) ions to deaerated acid toluene solutions are the formation of benzyl alcohol and benzaldehyde and an increase in the yield of 1,2-diphenylethane

Catalyzed reduction of nitrate in aqueous solutions

International Nuclear Information System (INIS)

Haas, P.A.

1994-08-01

Sodium nitrate and other nitrate salts in wastes is a major source of difficulty for permanent disposal. Reduction of nitrate using aluminum metal has been demonstrated, but NH 3 , hydrazine, or organic compounds containing oxygen would be advantageous for reduction of nitrate in sodium nitrate solutions. Objective of this seed money study was to determine minimum conditions for reduction. Proposed procedure was batchwise heating of aqueous solutions in closed vessels with monitoring of temperatures and pressures. A simple, convenient apparatus and procedure were demonstrated for observing formation of gaseous products and collecting samples for analyses. The test conditions were 250 degree C and 1000 psi max. Any useful reduction of sodium nitrate to sodium hydroxide as the primary product was not found. The nitrate present at pHs 3 or NH 4 NO 3 is easily decomposed, and the effect of nitromethane at these low pHs was confirmed. When acetic acid or formic acid was added, 21 to 56% of the nitrate in sodium nitrate solutions was reduced by methanol or formaldehyde. With hydrazine and acetic acid, 73 % of the nitrate was decomposed to convert NaNO 3 to sodium acetate. With hydrazine and formic acid, 36% of the nitrate was decomposed. If these products are more acceptable for final disposal than sodium nitrate, the reagents are cheap and the conversion conditions would be practical for easy use. Ammonium acetate or formate salts did not significantly reduce nitrate in sodium nitrate solutions

Free radicals generated by radiolysis of aqueous solutions

International Nuclear Information System (INIS)

Schwarz, H.A.

1981-01-01

The free radicals produced in the radiolysis of aqueous solutions span the range of redox potentials from -2.9 to +2.65 volts. The identity and nature of these radicals were discussed. Most of the discussion was results obtained with low LET radiation sources ( 60 Co gamma radiation or electron accelerators). Water radiolysis provides the synthesis of many radicals and radical ions in aqueous solution. The primary radicals, e/sub aq/ - H, OH, are well characterized. The radical population can be made to be 90% pure OH (or O - ) if N 2 O solutions are irradiated, the remaining 10% being H atoms. 55% of the radicals can be converted to H atoms in acid solution or in neutral phosphate solutions(e/sub aq/ - reacts with H 2 PO 4- to produce H). The remaining 45% (OH radicals) are difficult to convert to H by reaction with H 2 , due to the slow rate of the reaction. About 100 atmospheres of H 2 are required to do the conversion in less than 10 - 6 sec. 3 figures, 3 tables. (DP)

Hydrogen-bonded structure in highly concentrated aqueous LiBr solutions

International Nuclear Information System (INIS)

Imano, Masahiro; Kameda, Yasuo; Usuki, Takeshi; Uemura, Osamu

2001-01-01

Neutron diffraction measurements were carried out for H/D isotopically substituted aqueous 10, 25 and 33 mol% LiBr solutions in order to obtain structural information on the intermolecular hydrogen bonds among water molecules in highly concentrated aqueous solutions. Observed scattering cross sections for D 2 O (99.9 % D), 0 H 2 O(35.9 % D) and 0-2 H 2 O(68.0 % D) solutions were combined to deduce partial structure factors, a HH (Q), a XH (Q) and a XX (Q) (X: O, Br and Li). The least squares fitting analysis was applied to the observed partial structure factors to determine the nearest neighbor interatomic distance, root-mean-square amplitude and coordination number. Intermolecular distances, r OH =1.91(1) A, r HH =2.38(1) A and r OO =3.02(1) A, between the nearest neighbor water molecules, were obtained for the 10 mol% LiBr solution. On the other hand, the intermolecular O···H interaction was found to almost disappear in concentrated 25 and 33 mol% LiBr solutions. The result implies that the hydrogen-bonded network is completely broken in highly concentrated aqueous LiBr solutions. (author)

Water Evaporation from Acoustically Levitated Aqueous Solution Droplets.

Science.gov (United States)

Combe, Nicole A; Donaldson, D James

2017-09-28

We present a systematic study of the effect of solutes on the evaporation rate of acoustically levitated aqueous solution droplets by suspending individual droplets in a zero-relative humidity environment and measuring their size as a function of time. The ratios of the early time evaporation rates of six simple salts (NaCl, NaBr, NaNO 3 , KCl, MgCl 2 , CaCl 2 ) and malonic acid to that of water are in excellent agreement with predictions made by modifying the Maxwell equation to include the time-dependent water activity of the evaporating aqueous salt solution droplets. However, the early time evaporation rates of three ammonium salt solutions (NH 4 Cl, NH 4 NO 3 , (NH 4 ) 2 SO 4 ) are not significantly different from the evaporation rate of pure water. This finding is in accord with a previous report that ammonium sulfate does not depress the evaporation rate of its solutions, despite reducing its water vapor pressure, perhaps due to specific surface effects. At longer evaporation times, as the droplets approach crystallization, all but one (MgCl 2 ) of the solution evaporation rates are well described by the modified Maxwell equation.

Atmospheric plasma generates oxygen atoms as oxidizing species in aqueous solutions

International Nuclear Information System (INIS)

Hefny, Mohamed Mokhtar; Pattyn, Cedric; Benedikt, Jan; Lukes, Petr

2016-01-01

A remote microscale atmospheric pressure plasma jet ( µ APPJ) with He, He/H 2 O, He/O 2 , and He/O 2 /H 2 O gas mixtures was used to study the transport of reactive species from the gas phase into the liquid and the following aqueous phase chemistry. The effects induced by the µ APPJ in water were quantitatively studied using phenol as a chemical probe and by measuring H 2 O 2 concentration and pH values. These results were combined with the analysis of the absolute densities of the reactive species and the modeling of convective/diffusion transport and recombination reactions in the effluent of the plasma jet. Additionally, modified plasma jets were used to show that the role of emitted photons in aqueous chemistry is negligible for these plasma sources. The fastest phenol degradation was measured for the He/O 2 plasma, followed by He/H 2 O, He/O 2 /H 2 O, and He plasmas. The modeled quantitative flux of O atoms into the liquid in the He/O 2 plasma case was highly comparable with the phenol degradation rate and showed a very high transfer efficiency of reactive species from the plasma into the liquid, where more than half of the O atoms leaving the jet nozzle entered the liquid. The results indicate that the high oxidative effect of He/O 2 plasma was primarily due to solvated O atoms, whereas OH radicals dominated the oxidative effects induced in water by plasmas with other gas mixtures. These findings help to understand, in a quantitative way, the complex interaction of cold atmospheric plasmas with aqueous solutions and will allow a better understanding of the interaction of these plasmas with water or buffered solutions containing biological macromolecules, microorganisms, or even eukaryotic cells. Additionally, the µ APPJ He/O 2 plasma source seems to be an ideal tool for the generation of O atoms in aqueous solutions for any future studies of their reactivity. (paper)

Line emissions from sonoluminescence in aqueous solutions of halide salts without noble gases

Energy Technology Data Exchange (ETDEWEB)

Liang, Jinfu, E-mail: liang.shi2007@163.com [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); School of Physics and Electronic Science, Guizhou Normal University, Guiyang 550001 (China); Chen, Weizhong, E-mail: wzchen@nju.edu.cn [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China); Zhou, Chao; Cui, Weicheng; Chen, Zhan [The Key Laboratory of Modern Acoustics, Ministry of Education, Institution of Acoustics, Nanjing University, Nanjing 210093 (China)

2015-02-20

Line emissions of trivalent terbium (Tb{sup 3+}) ion were observed from single-bubble sonoluminescence (SL) in an aqueous solution of terbium chloride (TbCl{sub 3}) that contained no noble gas. In addition, sodium (Na) lines were observed in multi-bubble SL in aqueous solutions of various halide salts that contained no noble gas. These observations show that the halide ions, such as Cl{sup −}, Br{sup −}, and I{sup −}, help for line emissions as the noble gases. The intensity of a line emission depends on both the chemical species produced by cavitation bubbles and the temperature of SL bubble that responds to the driving ultrasound pressure. With the increase of driving pressure, some line emissions attached to the continuous spectrum may become increasingly clear, while other line emissions gradually become indistinct. - Highlights: • Line emissions of Tb(III) ions were observed without the presence of noble gases. • The halide ions help to generate a line emission during sonoluminescence. • The intensity of a line emission mainly depends on the bubble's temperature. • The definition of a line emission is related to the temperature of caviation bubble and the kind of host liquid.

EXTRACTION OF MONOAZO DYES BY HYDROPHILIC EXTRACTANTS FROM AQUEOUS SOLUTIONS

Directory of Open Access Journals (Sweden)

Y. I. Korenman

2012-01-01

Full Text Available The extraction of mono azo dyes E102, E122, E110, E124, E129 from aqueous solutions with hydrophilic solvents (alcohols, esters, ketones and polymers (poly-N-vinylamides, polyethylene glycol was studied. The main regularities of extraction are established. The distribution coefficients and degree of extraction of dyes was estimate. The influence of the nature of solvents and polymers on the extraction of dyes from aqueous solutions are established.

The effect of temperature on radiolysis of iodide ion diluted aqueous solutions

International Nuclear Information System (INIS)

Gorbovitskaya, T.; Tiliks, J.

1996-01-01

In order to investigate the radiolysis of iodine containing aqueous solutions a flow type facility - Iodine Thermoradiation Facility (ITF) has been designed. It has a possibility to irradiate aqueous solutions in the steel vessel with 60 Co γ-rays and continuously (on line) to analyze the products of radiolysis both in liquid and in gaseous phases. By means of ITF the formation of I ox (I 2 + I 3 - + HOI), IO 3 - , H 2 O 2 was studied in 10 -5 - 10 -3 mol/dm 3 CsI aqueous solutions by their radiolysis at dose rate 4.5 kGv/h for six hours in region of temperatures from 313 to 404 K. Under similar conditions, some experiments in glass ampoules were also performed. The steady-state concentrations of I ox and IO 3 - decreased with increasing temperature as linear function of inverted temperature. The effect decreased with decreasing concentration of iodide ion. As the result, at high temperatures (T≥380 K) the steady-state concentration of I ox does not depend essentially on the iodide ion initial concentration. Molecular iodine (I 2 ) released from the solution was the main radiolysis product in gaseous phase. Its steady-state concentration increased with increasing temperature because of iodine solubility in the water and decreased at the same time because the radiolytic iodine concentrations decreased. Therefore the most volatility of irradiated 10 -3 and 10 -4 M CsI solutions was observed at the temperature about 350 K. The volatility of 10 -5 M solutions gradually decreased with increasing temperature. The experimental data were explained on the base of the hypothesis that the reaction between I 2 and radiolytic H 2 O 2 was the limit one determining the temperature dependence of I ox and IO 3 - steady-state concentrations. Its activation energy was estimated to be 27,5 kcal.mol -1 . The temperature dependence for reaction (IO - + H 2 O 2 ) was also estimated. (author) 8 figs., 1 tab., 17 refs

Electrodialysis potential for fractionation of multicomponent aqueous solutions

Directory of Open Access Journals (Sweden)

Grzegorzek Martyna

2017-01-01

Full Text Available The paper aimed at the evaluation of the batch electrodialysis (ED run in the course of treatment and desalination of various aqueous mixtures containing both mineral (sodium fluoride, sodium chloride and organic substances (dyes or humic acids. The commercial ED stack (PCCell Bed equipped with standard anion-exchange and cation-exchange membranes or monovalent selective anion-exchange membranes was used. The ED experiments were performed at a constant current density (1.56 or 1.72 mA/cm2. The mechanism of ion migration as well as membrane deposition for variable solution composition and various membrane types was analyzed The calculated mass balance and electrical energy demand for each ED run were helpful in evaluating the membrane fouling intensity. It was found that the presence of organic substances in the treated solution had a minor impact on energy consumption, but rather strongly affected chloride flux. The extent of organics deposition was significantly lower for monovalent selective anion-exchange membranes than for classic anion-exchange membranes.

Luminescence properties of tetravalent uranium in aqueous solution

International Nuclear Information System (INIS)

Kirishima, A.; Kimura, T.; Nagaishi, R.; Tochiyama, O.

2004-01-01

The luminescence spectra of U 4+ in aqueous solutions were observed in the UV-VIS region at ambient and liquid nitrogen temperatures. The excitation spectrum indicates that the luminescence is arising from the deexcitation of a 5f electron at the 1 S 0 level and no other emissions of U 4+ in aqueous solutions were detected for other f-f transitions. All the luminescence peaks were assigned to the transitions from 1 S 0 to lower 5f levels. To estimate the luminescence lifetime, luminescence decay curves were measured using time-resolved laser-induced fluorescence spectroscopy. At room temperature, the decay curve indicated that the lifetime was shorter than 20 ns. On the other hand, the frozen sample of U 4+ in aqueous solution at liquid nitrogen temperature showed the same emission spectrum as at room temperature and its lifetime was 149 ns in H 2 O system and 198 ns in D 2 O system. The longer lifetime at liquid nitrogen temperature made it possible to measure the spectrum of U 4+ at the concentration as low as 10 -6 M. The difference in the anion species (ClO 4 - , Cl - , SO 4 2- ) affected the structure of the emission spectrum to some extent. (orig.)

Recoil halogen reactions in liquid and frozen aqueous solutions of biomolecules

International Nuclear Information System (INIS)

Arsenault, L.J.; Blotcky, A.J.; Firouzbakht, M.L.; Rack, E.P.; Nebraska Univ., Omaha

1982-01-01

Reactions of recoil 38 Cl, 80 Br and 128 I have been studied in crystalline systems of 5-halouracil, 5-halo-2'-deoxyuridine and 5-halouridine as well as liquid and frozen aqueous solutions of these halogenated biomolecules. In all systems expect crystalline 5-iuodouracil the major product was the radio-labelled halide ion. There was no evidence for other halogen inorganic species. The major labelled organic product was the parent molecule. A recoil atom tracer technique was developed to acquire site information of the biomolecule solutes in the liquid and frozen aqueous systems. For all liquid and frozen aqueous systems, the halogenated biomolecules tended to aggregate. For liquid systems, the tendency for aggregation diminished as the solute concentration approached zero, where the probable state of the solute approached a monomolecular dispersion. Unlike the liquid state, the frozen ice lattice demonstated a ''caging effect'' for the solute aggregates which resulted in constant product yields over the whole concentration range. (orig.)

A model for radiolysis of water and aqueous solutions of H2, H2O2 and O2

International Nuclear Information System (INIS)

Ershov, B.G.; Gordeev, A.V.

2008-01-01

Kinetic model for the radiolysis of pure water describing the formation of H 2 , H 2 O 2 and O 2 and the radiation chemical transformations of aqueous solutions containing these compounds over a broad range of concentrations, pH, absorbed doses and dose rates is proposed and substantiated. The model includes a set of chemical reactions with optimized rate constants and the radiation chemical yields of radiolysis products. The model applicability to the description of the whole set of data on the radiation chemical transformations of water and aqueous solutions of H 2 , H 2 O 2 and O 2 is demonstrated

GEOSURF: a computer program for modeling adsorption on mineral surfaces from aqueous solution

Science.gov (United States)

Sahai, Nita; Sverjensky, Dimitri A.

1998-11-01

A new program, GEOSURF, has been developed for calculating aqueous and surface speciation consistent with the triple-layer model of surface complexation. GEOSURF is an extension of the original programs MINEQL, MICROQL and HYDRAQL. We present, here, the basic algorithm of GEOSURF along with a description of the new features implemented. GEOSURF is linked to internally consistent data bases for surface species (SURFK.DAT) and for aqueous species (AQSOL.DAT). SURFK.DAT contains properties of minerals such as site densities, and equilibrium constants for adsorption of aqueous protons and electrolyte ions on a variety of oxides and hydroxides. The Helgeson, Kirkham and Flowers version of the extended Debye-Huckel Equation for 1:1 electrolytes is implemented for calculating aqueous activity coefficients. This permits the calculation of speciation at ionic strengths greater than 0.5 M. The activity of water is computed explicitly from the osmotic coefficient of the solution, and the total amount of electrolyte cation (or anion) is adjusted to satisfy the electroneutrality condition. Finally, the use of standard symbols for chemical species rather than species identification numbers is included to facilitate use of the program. One of the main limitations of GEOSURF is that aqueous and surface speciation can only be calculated at fixed pH and at fixed concentration of total adsorbate. Thus, the program cannot perform reaction-path calculations: it cannot determine whether or not a solution is over- or under-saturated with respect to one or more solid phases. To check the proper running of GEOSURF, we have compared results generated by GEOSURF with those from two other programs, HYDRAQL and EQ3. The Davies equation and the "bdot" equation, respectively, are used in the latter two programs for calculating aqueous activity coefficients. An example of the model fit to experimental data for rutile in 0.001 M-2.0 M NaNO 3 is included.

γ-radiation induced tetracycline removal in an aqueous solution

International Nuclear Information System (INIS)

Zhou Fei; Guo Zhaobing; Zhang Chaozhi; Lin Mingyue; Wu Menglong; Zhao Yongfu

2012-01-01

Degradation effect of tetracycline (TC) by γ-radiation was investigated in an aqueous solution. The effects of initial concentrations of TC, pH values, combining with H 2 O 2 or CH 3 OH on degradation of TC were studied. Results showed that TC can be effectively degradated by γ-irradiation in an aqueous solution. Degradation of TC could be remarkably improved both in acid solution and alkaline solution, especially when pH value was 9.0. In addition, H 2 O 2 could gently promote degradation of TC induced by γ-radiation. While, CH 3 OH markedly restrained degradation of TC induced by γ-radiation. The degradation mechanism of TC was supposed by results of quantum chemical calculations and LC-MS. Results proved that degradation of TC induced by γ-radiation was mainly ascribed to · OH oxidation. (authors)

Heavy metal removal from aqueous solutions by sorption using ...

African Journals Online (AJOL)

Heavy metal removal from aqueous solutions by sorption using natural clays from Burkina Faso. ... The high alkaline pH in one of the samples is attributable to the presence of ... The point of zero charge (pHpzc) values of the clays, as determined by ... significant contributions to the removal of metal ions in aqueous systems.

Synthesis of polypyrrole within the cell wall of yeast by redox-cycling of [Fe(CN)6](3-)/[Fe(CN)6](4-).

Science.gov (United States)

Ramanavicius, Arunas; Andriukonis, Eivydas; Stirke, Arunas; Mikoliunaite, Lina; Balevicius, Zigmas; Ramanaviciene, Almira

2016-02-01

Yeast cells are often used as a model system in various experiments. Moreover, due to their high metabolic activity, yeast cells have a potential to be applied as elements in the design of biofuel cells and biosensors. However a wider application of yeast cells in electrochemical systems is limited due to high electric resistance of their cell wall. In order to reduce this problem we have polymerized conducting polymer polypyrrole (Ppy) directly in the cell wall and/or within periplasmic membrane. In this research the formation of Ppy was induced by [Fe(CN)6](3-)ions, which were generated from K4[Fe(CN)6], which was initially added to polymerization solution. The redox process was catalyzed by oxido-reductases, which are present in the plasma membrane of yeast cells. The formation of Ppy was confirmed by spectrophotometry and atomic force microscopy. It was confirmed that the conducting polymer polypyrrole was formed within periplasmic space and/or within the cell wall of yeast cells, which were incubated in solution containing pyrrole, glucose and [Fe(CN)6](4-). After 24h drying at room temperature we have observed that Ppy-modified yeast cell walls retained their initial spherical form. In contrast to Ppy-modified cells, the walls of unmodified yeast have wrinkled after 24h drying. The viability of yeast cells in the presence of different pyrrole concentrations has been evaluated. Copyright © 2015 Elsevier Inc. All rights reserved.

Mechanisms of biochar assisted immobilization of Pb2+ by bioapatite in aqueous solution.

Science.gov (United States)

Shen, Zhengtao; Tian, Da; Zhang, Xinyu; Tang, Lingyi; Su, Mu; Zhang, Li; Li, Zhen; Hu, Shuijin; Hou, Deyi

2018-01-01

Bioapatite (BAp) is regarded as an effective material to immobilize lead (Pb 2+ ) via the formation of stable pyromorphite. However, when applied in contaminated soil, due to its low surface area and low adsorption capacity, BAp might not sufficiently contact and react with Pb 2+ . Biochar, a carbon storage material, typically has high surface area and high adsorption capacity. This study investigated the feasibility of using biochar as a reaction platform to enhance BAp immobilization of Pb 2+ . An alkaline biochar produced from wheat straw pellets (WSP) and a slightly acidic biochar produced from hardwood (SB) were selected. The results of aqueous adsorption showed the combination of biochar (WSP or SB) and BAp effectively removed Pb 2+ from the aqueous solution containing 1000 ppm Pb 2+ . XRD, ATR-IR, and SEM/EDX results revealed the formation of hydroxypyromorphite on both biochars' surfaces. This study demonstrates that biochars could act as an efficient reaction platform for BAp and Pb 2+ in aqueous solution due to their high surface area, porous structure, and high adsorption capacity. Therefore, it is mechanistically feasible to apply biochar to enhance BAp immobilization of Pb 2+ in contaminated soil. Copyright © 2017 Elsevier Ltd. All rights reserved.

Complex chemistry of Np(V) in aqueous solutions

International Nuclear Information System (INIS)

Inoue, Yasushi

1989-01-01

Despite the importance of Np(V) in both the nuclear chemical engineering and the actinoid chemistry, little work has been performed on the complex chemistry of Np(V) in aqueous solutions, since Np(V) reacts less readily with various ligands. The author has directed his effort to understand the chemical behavior of Np(V) in aqueous solutions, especially the determination of the stability constants of Np(V) complexes with various ligands. A part of the results obtained so far is presented in the following order. (1) The synergistic extraction of Np(V) as a method for studying the complex chemistry of Np(V): TTA-MTOA(methyltrioctylammonium chloride), TTA-phen and TTA-TOPO. (2) The determination of the stability constants of Np(V) complexes with 22 organic- and 5 inorganic ligands by means of the solvent extraction. (3) The distribution of the chemical species of Np(V) in solutions under various conditions

Behavior of Paramecium sp. in solutions containing Sr and Pb: Do Paramecium sp. alter chemical forms of those metals?

International Nuclear Information System (INIS)

Kozai, Naofumi; Ohnuki, Toshihiko; Koka, Masahi; Satoh, Takahiro; Kamiya, Tomihiro

2011-01-01

The behavior of Paramecium sp. (Paramecium bursaria) in aqueous solutions containing Sr and Pb was investigated to determine the role of protozoa in the migration of radionuclides in the environment. Precultured living cells of P. bursaria were exposed to aqueous solutions containing 0.01 or 0.05 mM Sr or Pb at pH 7 for 24 h. For comparison, pre-killed cells were treated with the metal solutions in the same way. Two-dimensional elemental mappings of cells were obtained by micro-PIXE. Aquatic species of Sr and Pb were analyzed by size exclusion chromatography (SEC) coupled online to ultraviolet (UV) spectroscopy and inductivity coupled plasma mass spectroscopy (ICP-MS). The amounts of Sr adsorbed or taken up by the cells surviving for 24 h and adsorbed on pre-killed cells were below the detection limit. Cells of P. bursaria adsorbed or took up a fraction of Pb. The Pb adsorbed or taken up by the cells surviving for 24 h in the Pb solution was barely detectable, while the Pb adsorbed on pre-killed cells was clearly mappable. These findings suggest that living cells of P. bursaria have functions that reduce adsorption or uptake of Pb on the cells. Quantitative and SEC-UV-ICP-MS analyses of the Sr and Pb in aqueous phases showed no clear evidences that living cells of P. bursaria alter the chemical form of Sr or Pb remaining in the aqueous phases after the cell-solution contact.

Behavior of Paramecium sp. in solutions containing Sr and Pb: Do Paramecium sp. alter chemical forms of those metals?

Science.gov (United States)

Kozai, Naofumi; Ohnuki, Toshihiko; Koka, Masahi; Satoh, Takahiro; Kamiya, Tomihiro

2011-10-01

The behavior of Paramecium sp. (Paramecium bursaria) in aqueous solutions containing Sr and Pb was investigated to determine the role of protozoa in the migration of radionuclides in the environment. Precultured living cells of P. bursaria were exposed to aqueous solutions containing 0.01 or 0.05 mM Sr or Pb at pH 7 for 24 h. For comparison, pre-killed cells were treated with the metal solutions in the same way. Two-dimensional elemental mappings of cells were obtained by micro-PIXE. Aquatic species of Sr and Pb were analyzed by size exclusion chromatography (SEC) coupled online to ultraviolet (UV) spectroscopy and inductivity coupled plasma mass spectroscopy (ICP-MS). The amounts of Sr adsorbed or taken up by the cells surviving for 24 h and adsorbed on pre-killed cells were below the detection limit. Cells of P. bursaria adsorbed or took up a fraction of Pb. The Pb adsorbed or taken up by the cells surviving for 24 h in the Pb solution was barely detectable, while the Pb adsorbed on pre-killed cells was clearly mappable. These findings suggest that living cells of P. bursaria have functions that reduce adsorption or uptake of Pb on the cells. Quantitative and SEC-UV-ICP-MS analyses of the Sr and Pb in aqueous phases showed no clear evidences that living cells of P. bursaria alter the chemical form of Sr or Pb remaining in the aqueous phases after the cell-solution contact.

Behavior of Paramecium sp. in solutions containing Sr and Pb: Do Paramecium sp. alter chemical forms of those metals?

Energy Technology Data Exchange (ETDEWEB)

Kozai, Naofumi, E-mail: kozai.naofumi@jaea.go.jp [Advanced Sciences Research Center, Japan Atomic Energy Agency (JAEA), Tokai, Ibaraki 319-1195 (Japan); Ohnuki, Toshihiko [Advanced Sciences Research Center, Japan Atomic Energy Agency (JAEA), Tokai, Ibaraki 319-1195 (Japan); Koka, Masahi; Satoh, Takahiro; Kamiya, Tomihiro [Takasaki Advanced Radiation Research Institute, JAEA, 1233 Watanuki-machi, Takasaki, Gunma 370-1292 (Japan)

2011-10-15

The behavior of Paramecium sp. (Paramecium bursaria) in aqueous solutions containing Sr and Pb was investigated to determine the role of protozoa in the migration of radionuclides in the environment. Precultured living cells of P. bursaria were exposed to aqueous solutions containing 0.01 or 0.05 mM Sr or Pb at pH 7 for 24 h. For comparison, pre-killed cells were treated with the metal solutions in the same way. Two-dimensional elemental mappings of cells were obtained by micro-PIXE. Aquatic species of Sr and Pb were analyzed by size exclusion chromatography (SEC) coupled online to ultraviolet (UV) spectroscopy and inductivity coupled plasma mass spectroscopy (ICP-MS). The amounts of Sr adsorbed or taken up by the cells surviving for 24 h and adsorbed on pre-killed cells were below the detection limit. Cells of P. bursaria adsorbed or took up a fraction of Pb. The Pb adsorbed or taken up by the cells surviving for 24 h in the Pb solution was barely detectable, while the Pb adsorbed on pre-killed cells was clearly mappable. These findings suggest that living cells of P. bursaria have functions that reduce adsorption or uptake of Pb on the cells. Quantitative and SEC-UV-ICP-MS analyses of the Sr and Pb in aqueous phases showed no clear evidences that living cells of P. bursaria alter the chemical form of Sr or Pb remaining in the aqueous phases after the cell-solution contact.

CdSe nanoparticles grown via radiolytic methods in aqueous solutions

International Nuclear Information System (INIS)

Singh, Shalini; Rath, M.C.; Singh, A.K.; Mukherjee, T.; Jayakumar, O.D.; Tyagi, A.K.; Sarkar, S.K.

2011-01-01

Cadmium selenide, CdSe, nanoparticles have been synthesized in aqueous solution containing equimolar ammoniated CdSO 4 and Na 2 SeSO 3 as the starting materials without any capping agents, using gamma and electron beam irradiation under a reducing condition. The radiolytic processes occurring in water result in the formation of CdSe nanoparticles through the reactions mediated by hydrated electrons, e aq - . TEM measurements revealed that the CdSe nanoparticles were found to exist in agglomerates of dimension of about 100 nm, consisting of primary nanoparticles of dimensions within 5 nm. The as-grown nanoparticles were of cubic crystalline phase as supported by the XRD measurements. These bare CdSe nanoparticles exhibit room temperature ferromagnetic (RTFM) behavior. However, the RTFM behavior was found to be 30% higher in the case of CdSe nanoparticles prepared on electron beam irradiation as compared to those obtained by gamma irradiation, which was attributed to their relatively smaller size (2-3 nm) and disordered structures as compared to those obtained in the later case (3-5 nm). -- Research highlights: → CdSe nanoparticles could be synthesized in aqueous solutions containing equimolar ammoniated CdSO 4 and Na 2 SeSO 3 as the starting materials using gamma and electron beam irradiation under a reducing condition. → CdSe nanoparticles were found to exist in agglomerates of dimension of about 100 nm, consisting of primary nanoparticles of dimensions within 5 nm. → CdSe nanoparticles exhibit room temperature ferromagnetic (RTFM) behavior. → The RTFM behavior was found to be 30% higher in the case of CdSe nanoparticles prepared on electron beam irradiation as compared to those obtained by gamma irradiation.

Flotation separation of hafnium(IV) from aqueous solutions

International Nuclear Information System (INIS)

Downey, D.M.; Narick, C.N.; Cohen, T.A.

1985-01-01

A simple, rapid method for the separation of hafnium from aqueous solutions was investigated using sup(175+181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described. (author)

Treatment of infectious skin defects or ulcers with electrolyzed strong acid aqueous solution.

Science.gov (United States)

Sekiya, S; Ohmori, K; Harii, K

1997-01-01

A chronic ulcer with an infection such as methicillin-resistant Staphylococcus aureus is hard to heal. Plastic and reconstructive surgeons often encounter such chronic ulcers that are resistant to surgical or various conservative treatments. We applied conservative treatment using an electrolyzed strong acid aqueous solution and obtained satisfactory results. The lesion was washed with the solution or soaked in a bowl of the solution for approximately 20 min twice a day. Fresh electrolyzed strong acid aqueous solution is unstable and should be stored in a cool, dark site in a sealed bottle. It should be used within a week after it has been produced. Here we report on 15 cases of infectious ulcers that were treated by electrolyzed strong acid aqueous solution. Of these cases, 7 patients were healed, 3 were granulated, and in 5, infection subsided. In most cases the lesion became less reddish and less edematous. Discharge or foul odor from the lesion was decreased. Electrolyzed strong acid aqueous solution was especially effective for treating a chronic refractory ulcer combined with diabetes melitus or peripheral circulatory insufficiency. This clinically applied therapy of electrolyzed strong acid aqueous solution was found to be effective so that this new therapeutic technique for ulcer treatment can now be conveniently utilized.

MoS2 Nanocube structures as catalysts for electrochemical H2 evolution from acidic aqueous solutions

NARCIS (Netherlands)

Maijenburg, A.W.; Regis, M.; Hattori, A.N.; Tanaka, H.; Choi, K.-S.; ten Elshof, Johan E.

2014-01-01

Core–shell PMMA–Au nanocube structures made by a combination of nanoimprint lithography and sidewall deposition were used as template for electrodeposition of MoS2, Ni, and Pt. Linear sweep voltammetry experiments obtained in an aqueous solution containing 0.29 M H2SO4 (pH 0.24) showed that the

Radiolysis of Aqueous Toluene Solutions

Energy Technology Data Exchange (ETDEWEB)

Christensen, H C; Gustafson, R

1971-04-15

Aqueous toluene solutions have been irradiated with Co gamma-rays. In unbuffered solutions the various cresol isomers are formed in a total yield of 0.45, 0.87 and 0.94 molecules/100 eV absorbed energy in argon-, N{sub 2}O- and air - saturated solutions, respectively. The yields are reduced in acid (pH 3) solutions (G = 0.14, 0.14 and 0.52, respectively) but the reduction is compensated by the formation of 1,2-di-phenylethane in yields of 0.49 and 1.60 in argon- and N{sub 2}O-saturated solutions, respectively. Benzyl radicals are formed through an acid catalysed water elimination reaction from the initially formed hydroxymethylcyclohexadienyl radical. Phenyltolylmethanes, dimethylbiphenyls and partly reduced dimers are also formed during the radiolysis. Hydrogen is formed in the same yield as the molecular yield, g(H{sub 2}). Xylene isomers and benzene are formed in trace quantities. The most remarkable effects of the addition of Fe(III) ions to deaerated acid toluene solutions are the formation of benzyl alcohol and benzaldehyde and an increase in the yield of 1,2-diphenylethane

Effects of Radiosterilization on Sealed Aqueous Solutions

International Nuclear Information System (INIS)

Pandula, E.L.; Farkas, E.; Rácz, I.

1967-01-01

For aqueous solutions sensitive to heat,and in connection with the use of plastic ampoules, the need for applying radiosterilization is growing. Studying the possibilities of radiosterilization, experiments were made with the following: 0.1% atropine, 1.0% morphine, and 2% lidocain in aqueous solutions. The aim of the work was to establish whether the active ingredients of the injections suffer decomposition or not, to study the factors influencing the degradation and, furthermore, to make attempts to prevent decomposition. The samples were irradiated by 420 Ci 60 Co γ-radiation source. The applied doses were 1 to 2.5 Mrad, with a 10 4 to 2.5 x 10 5 rad/h dose intensity. After irradiation the change in colour, pH-value, concentration and UV-spectra were studied. Changes of the last three types were found. Studying the factors influencing decomposition it has been found that the degree of degradation was increased by the increase of radiation dose, increase of concentration, decrease of dose intensity, and increase of oxygen content in the atmosphere over the solution. Attempts were made to prevent degradation. Solutions were prepared with sulphite, ascorbic acid, and AET, and some measure of success was achieved, especially with the sulphite addition. (author)

Evaluation of SCS-CN method using a fully distributed physically based coupled surface-subsurface flow model

Science.gov (United States)

Shokri, Ali

2017-04-01

The hydrological cycle contains a wide range of linked surface and subsurface flow processes. In spite of natural connections between surface water and groundwater, historically, these processes have been studied separately. The current trend in hydrological distributed physically based model development is to combine distributed surface water models with distributed subsurface flow models. This combination results in a better estimation of the temporal and spatial variability of the interaction between surface and subsurface flow. On the other hand, simple lumped models such as the Soil Conservation Service Curve Number (SCS-CN) are still quite common because of their simplicity. In spite of the popularity of the SCS-CN method, there have always been concerns about the ambiguity of the SCS-CN method in explaining physical mechanism of rainfall-runoff processes. The aim of this study is to minimize these ambiguity by establishing a method to find an equivalence of the SCS-CN solution to the DrainFlow model, which is a fully distributed physically based coupled surface-subsurface flow model. In this paper, two hypothetical v-catchment tests are designed and the direct runoff from a storm event are calculated by both SCS-CN and DrainFlow models. To find a comparable solution to runoff prediction through the SCS-CN and DrainFlow, the variance between runoff predictions by the two models are minimized by changing Curve Number (CN) and initial abstraction (Ia) values. Results of this study have led to a set of lumped model parameters (CN and Ia) for each catchment that is comparable to a set of physically based parameters including hydraulic conductivity, Manning roughness coefficient, ground surface slope, and specific storage. Considering the lack of physical interpretation in CN and Ia is often argued as a weakness of SCS-CN method, the novel method in this paper gives a physical explanation to CN and Ia.

Photochemical properties of Ysub(t) base in aqueous solution

International Nuclear Information System (INIS)

Paszyc, S.; Rafalska, M.

1979-01-01

Photoreactivity of Ysub(t) base (I) has been studied in aqueous solution (pH-6) saturated with oxygen. Two photoproducts (II,III), resulting from irradiation at lambda = 253.7 nm and lambda >= 290 nm were isolated and their structures determined. The quantum yield for Ysub(t) base disappearance (rho dis) is 0.002 (lambda = 313 nm). It was shown that dye- sensitised photo-oxidation of Ysub(t) base in aqueous solution occurs according to a Type I mechanism as well as with participation of singlet state oxygen. Quantum yields, fluorescence decay times and phosphorescence of Ysub(t) base have also been determined. (author)

Aqueous solutions of ionic liquids: microscopic assembly

NARCIS (Netherlands)

Vicent-Luna, J.M.; Dubbeldam, D.; Gómez-Álvarez, P.; Calero, S.

2016-01-01

Aqueous solutions of ionic liquids are of special interest, due to the distinctive properties of ionic liquids, in particular, their amphiphilic character. A better understanding of the structure-property relationships of such systems is hence desirable. One of the crucial molecular-level

Kinetics of the exchange of oxygen between carbon dioxide and carbonate in aqueous solution

International Nuclear Information System (INIS)

Tu, C.K.; Silverman, D.N.

1975-01-01

A kinetic analysis of the exchange of oxygen between carbon dioxide and carbonate ion in alkaline, aqueous solutions is presented. The exchange was observed by placing 18 O-labeled carbonate, not enriched in 13 C, into solution with 13 C-enriched carbonate, not enriched in 18 O. The rate of depletion of 18 O from the 12 C-containing species and the rate of appearance of 18 O in the 13 C-containing species was measured by mass spectrometry. From these data, the second-order rate constant for the reaction between carbon dioxide and carbonate which results in the exchange of oxygen at 25 0 is 114 +- 11 M -1 sec -1 . It is emphasized that this exchange of oxygen between species of CO 2 in solution must be recognized in studies using 18 O labels to determine the fate of CO 2 in biochemical and physiological processes. (auth)

Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

CERN Document Server

Matubayasi, Norihiro

2013-01-01

Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

Adsorption of lead from aqueous solutions by poly (methyl methacrylate)

International Nuclear Information System (INIS)

Din, M.; Hussain, R.

1992-01-01

The adsorption capability of commercially manufactured poly (methyl methacrylate) for lead in aqueous medium has been investigated. Percent adsorption and distribution coefficient values have been determined in relation to the shaking time, amount of adsorbent, pH effects and concentration of lead in the solution. The experimental results are compatible with Freundlich type of adsorption behavior. It is discernible from the experimental results that poly (methyl methacrylate) can be used for the removal of lead from slightly acidic aqueous solutions. (author)

Removal of dexamethasone from aqueous solution and hospital wastewater by electrocoagulation

International Nuclear Information System (INIS)

Arsand, Daniel R.; Kümmerer, Klaus; Martins, Ayrton F.

2013-01-01

This study is concerned with the removal of the anti-inflammatory dexamethasone from aqueous solution and hospital wastewater by electrocoagulation. The variation of the toxicity during the electrocoagulation was also studied through experiments that were designed and optimized by means of response surface methodology. The coagulation efficiency was evaluated by measuring the dexamethasone concentration by high performance liquid chromatography coupled to a diode array detector. In addition, variation was evaluated through a Vibrio fischeri test. The results showed an increase in the removal of dexamethasone (up to 38.1%) with a rise of the current applied and a decrease of the inter-electrode distance, in aqueous solutions. The application to hospital effluent showed similar results for the removal of dexamethasone. The main effect of the electrocoagulation was that it removed colloids and reduced the organic load of the hospital wastewater. Regarding the current applied, the calculated energy efficiency was 100%. Without pH adjustment of the aqueous solution or hospital wastewater, the residual aluminum concentration always remained lower than 10 mg L −1 , and, with adjustment (to pH 6.5), lower than 0.30 mg L −1 , at the final stage. No toxicity variation was observed during the electrocoagulation process in aqueous solution, either in the presence or absence of dexamethasone. - Highlights: ► Removal of DEX and organic load from aqueous solution and hospital wastewater by EC ► Evaluation of the toxicity during the removal of DEX by EC ► Suggestion of the EC process as a pretreatment for subsequent processes

Removal of dexamethasone from aqueous solution and hospital wastewater by electrocoagulation

Energy Technology Data Exchange (ETDEWEB)

Arsand, Daniel R., E-mail: danielarsand@pelotas.ifsul.edu.br [Chemistry Department, Federal University of Santa Maria, RS (Brazil); Kümmerer, Klaus, E-mail: klaus.kuemmerer@leuphana.de [Institute for Environmental Chemistry, Leuphana University Lüneburg (Germany); Martins, Ayrton F., E-mail: martins@quimica.ufsm.br [Chemistry Department, Federal University of Santa Maria, RS (Brazil)

2013-01-15

This study is concerned with the removal of the anti-inflammatory dexamethasone from aqueous solution and hospital wastewater by electrocoagulation. The variation of the toxicity during the electrocoagulation was also studied through experiments that were designed and optimized by means of response surface methodology. The coagulation efficiency was evaluated by measuring the dexamethasone concentration by high performance liquid chromatography coupled to a diode array detector. In addition, variation was evaluated through a Vibrio fischeri test. The results showed an increase in the removal of dexamethasone (up to 38.1%) with a rise of the current applied and a decrease of the inter-electrode distance, in aqueous solutions. The application to hospital effluent showed similar results for the removal of dexamethasone. The main effect of the electrocoagulation was that it removed colloids and reduced the organic load of the hospital wastewater. Regarding the current applied, the calculated energy efficiency was 100%. Without pH adjustment of the aqueous solution or hospital wastewater, the residual aluminum concentration always remained lower than 10 mg L{sup −1}, and, with adjustment (to pH 6.5), lower than 0.30 mg L{sup −1}, at the final stage. No toxicity variation was observed during the electrocoagulation process in aqueous solution, either in the presence or absence of dexamethasone. - Highlights: ► Removal of DEX and organic load from aqueous solution and hospital wastewater by EC ► Evaluation of the toxicity during the removal of DEX by EC ► Suggestion of the EC process as a pretreatment for subsequent processes.

Flotation separation of hafnium(IV) from aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Downey, D.M.; Narick, C.N.; Cohen, T.A.

1985-09-01

A simple, rapid method for the separation of hafnium from aqueous solutions was investigated using sup(175 + 181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described. (author). 21 refs.; 5 figs.

Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

Energy Technology Data Exchange (ETDEWEB)

Cochrane, T. T., E-mail: agteca@hotmail.com [AGTECA S.A., 230 Oceanbeach Road, Mount Maunganui, Tauranga 3116 (New Zealand); Cochrane, T. A., E-mail: tom.cochrane@canterbury.ac.nz [Department of Civil and Natural Resources Engineering, University of Canterbury, Private Bag 4800, Christchurch 8140 (New Zealand)

2016-01-15

Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N{sub f},” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N{sub f} was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N{sub f}, the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N{sub f

Osmotic potential calculations of inorganic and organic aqueous solutions over wide solute concentration levels and temperatures

International Nuclear Information System (INIS)

Cochrane, T. T.; Cochrane, T. A.

2016-01-01

Purpose: To demonstrate that the authors’ new “aqueous solution vs pure water” equation to calculate osmotic potential may be used to calculate the osmotic potentials of inorganic and organic aqueous solutions over wide ranges of solute concentrations and temperatures. Currently, the osmotic potentials of solutions used for medical purposes are calculated from equations based on the thermodynamics of the gas laws which are only accurate at low temperature and solute concentration levels. Some solutions used in medicine may need their osmotic potentials calculated more accurately to take into account solute concentrations and temperatures. Methods: The authors experimented with their new equation for calculating the osmotic potentials of inorganic and organic aqueous solutions up to and beyond body temperatures by adjusting three of its factors; (a) the volume property of pure water, (b) the number of “free” water molecules per unit volume of solution, “N f ,” and (c) the “t” factor expressing the cooperative structural relaxation time of pure water at given temperatures. Adequate information on the volume property of pure water at different temperatures is available in the literature. However, as little information on the relative densities of inorganic and organic solutions, respectively, at varying temperatures needed to calculate N f was available, provisional equations were formulated to approximate values. Those values together with tentative t values for different temperatures chosen from values calculated by different workers were substituted into the authors’ equation to demonstrate how osmotic potentials could be estimated over temperatures up to and beyond bodily temperatures. Results: The provisional equations formulated to calculate N f , the number of free water molecules per unit volume of inorganic and organic solute solutions, respectively, over wide concentration ranges compared well with the calculations of N f using recorded

Spinning of Fibers from Aqueous Solutions

Science.gov (United States)

2003-08-01

recombinant silk product BioSteel . Publications, patents and presentations 1. Arcidiacono, S., et al., Purification and characterization of recombinant...ABSTRACT Previous funding supporting this research focused primarily on development of the aqueous-based method for processing silk into spin solutions. Much...of this effort consisted of production of recombinant silk protein in bacterial and yeast expression systems. In spite of the small quantities

(Surfactant + polymer) interaction parameter studied by (liquid + liquid) equilibrium data of quaternary aqueous solution containing surfactant, polymer, and salt

Energy Technology Data Exchange (ETDEWEB)

Foroutan, Masumeh [Physical Chemistry Department, School of Chemistry, College of Science, University of Tehran, 14155-6455 Tehran (Iran, Islamic Republic of)], E-mail: foroutan@khayam.ut.ac.ir; Heidari, Nosrat; Mohammadlou, Maryam [Chemistry Department, Faculty of Science, Uremia University, Uremia (Iran, Islamic Republic of); Sojahrood, Amin Jafari [Physics Department, Faculty of Science, Uremia University, Uremia (Iran, Islamic Republic of)

2009-02-15

(Liquid + liquid) equilibrium (LLE) data of quaternary aqueous system containing polyoxyethylene (20) cetyl ether (with abbreviation name Brij 58, non-ionic surfactant), diammonium hydrogen phosphate, and poly ethylene glycol (PEG) with three molar masses {l_brace}M{sub W} = (1000, 6000, and 35,000) g . mol{sup -1}{r_brace} have been determined experimentally at T = 313.15 K. Furthermore, the Flory-Huggins theory with two electrostatic terms (Debye-Hueckel and Pitzer-Debye-Hueckel equations) have been used to calculate the phase behavior of the quaternary systems and (surfactant + polymer) interaction parameter as well as interaction parameters between other species. Temperature dependency of the parameters of the Flory-Huggins theory has been obtained. Also an effort have been done to show that addition of PEG as well as increasing the temperature can shift the binodal curves of the ternary aqueous system containing surfactant and salt to lower mole fraction of salt. Also the effect of polymer molar mass on the binodal diagram displacement has been discussed.

Electro-gravimetric recovery of silver from aqueous solutions and its precursors

Directory of Open Access Journals (Sweden)

A. Shah,

2016-08-01

Full Text Available A simple electrolytic cell was used for electrochemical recovery of silver from aqueous solutions containing 100 mg/L Ag(I. Two different sets of electrodes were applied to find the enhanced recovery of silver. Rocks and ores samples were processed through fire assay method and acid digestion. A set of electrodes comprised of stainless steel anode and aluminum cathode gave maximum recovery (96.5% of silver. This simple, robust, environment friendly and highly sensitive method was effectively applied to various ores and rock samples. The developed method with slight modifications can also be applied for the recovery of other metals.

In Situ Structural Characterization of Ferric Iron Dimers in Aqueous Solutions

DEFF Research Database (Denmark)

Zhu, Mengqiang; Puls, Brendan W.; Frandsen, Cathrine

2013-01-01

The structure of ferric iron (Fe3+) dimers in aqueous solutions has long been debated. In this work, we have determined the dimer structure in situ in aqueous solutions using extended X-ray absorption fine structure (EXAFS) spectroscopy. An Fe K-edge EXAFS analysis of 0.2 M ferric nitrate solutions...... at pH 1.28–1.81 identified a Fe–Fe distance at ∼3.6 Å, strongly indicating that the dimers take the μ-oxo form. The EXAFS analysis also indicates two short Fe–O bonds at ∼1.80 Å and ten long Fe–O bonds at ∼2.08 Å, consistent with the μ-oxo dimer structure. The scattering from the Fe–Fe paths interferes...... confirmed by Mössbauer analyses of analogous quick frozen solutions. This work also explores the electronic structure and the relative stability of the μ-oxo dimer in a comparison to the dihydroxo dimer using density function theory (DFT) calculations. The identification of such dimers in aqueous solutions...

Potential and problems of an aqueous lithium salt solution blanket for NET

International Nuclear Information System (INIS)

Kuechle, M.; Bojarsky, E.; Dorner, S.; Fischer, U.; Reimann, J.; Reiser, H.

1987-07-01

The report describes design studies on a water cooled in-vessel shield blanket for NET and its modification into an aqueous lithium salt blanket. The shield blankets are exchangable against breeding blankets and fulfill their shielding and heat removal functions. Emphasis is on simplicity and reliability. The water cooled shield is a large steel container in the shape of the blanket segment which is filled by water and containes a grid structure of poloidally arranged steel plates. The water flows several times in poloidal direction through the channels formed by the steel plates and is thereby heated up from 40degC to 70degC. When the water is replaced by an aqueous lithium salt solution the shield can be converted into a tritium breeding blanket without any design modification or invessel component replacement. When compared with other concepts this blanket has the advantage that the solution can replace water cooling also in the divertor and in segments dedicated to plasma heating and diagnostics, what increases the coverage considerably. Extensive three-dimensional neutronics calculations were done which, together with literature studies on candidate materials, corrosion, and tritium recovery led to a first assessment of the concept. There is an indication that no major corrosion problems are to be expected in the low temperature region envisaged. Tritium recovery capital costs were estimated to be in the 20 MECU to 50 MECU range and tritium breeding ratio is comparable to the best breeding blanket. (orig./GG) [de

Effect of pKa on the kinetics of carbon dioxide absorption in aqueous alkanolamine solutions containing carbonic anhydrase at 298K

NARCIS (Netherlands)

Penders-van Elk, Nathalie J M C; Fradette, Sylvie; Versteeg, Geert F.

2015-01-01

The absorption of carbon dioxide in various aqueous alkanolamine solutions have been studied with and without carbonic anhydrase respectively in a stirred cell reactor at 298K. The examined alkanolamines were: N,N-diethylethanolamine (DEMEA), N,N-dimethylethanolamine (DMMEA), monoethanolamine (MEA),

Photoproduction of hydroxyl radicals in aqueous solution with algae under high-pressure mercury lamp.

Science.gov (United States)

Liu, Xianli; Wu, Feng; Deng, Nansheng

2004-01-01

Photoproduction of hydroxyl radicals (*OH) could be induced in aqueous solution with algae (Nitzschia hantzschiana, etc.) and (or not) Fe3+ under high-pressure mercury lamp with an exposure time of 4 h. *OH was determined by HPLC using benzene as a probe. The photoproduction of *OH increased with increasing algae concentration. Fe3+ could enhance the photoproduction of *OH in aqueous solution with algae. The results showed that the photoproduction of *OH in algal solution with Fe3+ was greater than that in algal solution without Fe3+. The light intensity and pH affected the photoproduction of *OH in aqueous solution with algae with/without Fe3+. The photoproduction of *OH in aqueous solution with algae and Fe3+ under 250 W was greater than that under 125 W HPML. The photoproduction of *OH in algal solution (pH ranged from 4.0 to 7.0) with (or not) Fe3+ at pH 4 was the greatest.

Pulse radiolysis of anthraquinone dye aqueous solution

International Nuclear Information System (INIS)

Perkowski, J.; Gebicki, J.L.; Lubis, R.; Mayer, J.

1988-01-01

Pulse radiolysis of argon flushed aqueous solutions of 10 -5 -10 -4 mol dm -3 anthraquinone dye (C.I. Acid Blue 62) gives rise to the transients originated from the reactions of e - aq , OH and H. The rate constants of these reactions are determined. (author)

Effects of C/N ratio on nitrate removal and floc morphology of autohydrogenotrophic bacteria in a nitrate-containing wastewater treatment process.

Science.gov (United States)

Nguyen, Tran Ngoc Phu; Chao, Shu-Ju; Chen, Pei-Chung; Huang, Chihpin

2018-07-01

The effects of C/N ratio of a nitrate-containing wastewater on nitrate removal performed by autohydrogenotrophic bacteria as well as on the morphological parameters of floc such as floc morphology, floc number distribution, mean particle size (MPS), aspect ratio and transparency were examined in this study. The results showed that the nitrate reduction rate increased with increasing C/N ratio from 0.5 to 10 and that the nitrogen removal of up to 95% was found at the C/N ratios of higher than 5 (between 0.5-10). Besides, high C/N ratio values reflected a corresponding high nitrite accumulation after 12-hr operation, and a fast decreasing rate of nitrite in the rest of operational time. The final pH values increased with the C/N ratio increasing from 0.5 to 2.5, but decreased with the C/N ratio increasing from 2.5 to 10. There were no significant changes in floc morphology with the MPSs ranging from 35 to 40μm. Small and medium-sized flocs were dominant in the sludge suspension, and the number of flocs increased with the increasing C/N ratios. Furthermore, the highest apparent frequency of 10% was observed at aspect ratios of 0.5 and 0.6, while the transparency of flocs changed from 0.1 to 0.7. Copyright © 2017. Published by Elsevier B.V.

Separation of Co2+ present in aqueous solution on calcium carbonate

International Nuclear Information System (INIS)

Garcia A, E.; Granados C, F.

2008-01-01

The CaCO 3 was synthesized by precipitation method and characterized using SEM, EDS, TGA and IR. It was studied the adsorption behavior of Co 2+ present in aqueous solution on the synthesized material by experiments batch type at room temperature. Was found that removal of cobalt ions was greater than 40% indicating that this material can be used to remove Co 2+ present in aqueous solution. (Author)

Molecular dispersion energy parameters for alkali and halide ions in aqueous solution

International Nuclear Information System (INIS)

Reiser, S.; Deublein, S.; Hasse, H.; Vrabec, J.

2014-01-01

Thermodynamic properties of aqueous solutions containing alkali and halide ions are determined by molecular simulation. The following ions are studied: Li + , Na + , K + , Rb + , Cs + , F − , Cl − , Br − , and I − . The employed ion force fields consist of one Lennard-Jones (LJ) site and one concentric point charge with a magnitude of ±1 e. The SPC/E model is used for water. The LJ size parameter of the ion models is taken from Deublein et al. [J. Chem. Phys. 136, 084501 (2012)], while the LJ energy parameter is determined in the present study based on experimental self-diffusion coefficient data of the alkali cations and the halide anions in aqueous solutions as well as the position of the first maximum of the radial distribution function of water around the ions. On the basis of these force field parameters, the electric conductivity, the hydration dynamics of water molecules around the ions, and the enthalpy of hydration is predicted. Considering a wide range of salinity, this study is conducted at temperatures of 293.15 and 298.15 K and a pressure of 1 bar

Assessing the effectiveness of 30% sodium chloride aqueous solution for the preservation of fixed anatomical specimens: a 5-year follow-up study.

Science.gov (United States)

de Oliveira, Fabrício Singaretti

2014-07-01

Anatomical specimens used in human or veterinary anatomy laboratories are usually prepared with formaldehyde (a cancerous and teratogenic substance), glycerin (an expensive and viscous fluid), or ethanol (which is flammable). This research aimed to verify the viability of an aqueous 30% sodium chloride solution for preservation of anatomical specimens previously fixed with formaldehyde. Anatomical specimens of ruminant, carnivorous, equine, swine and birds were used. All were previously fixed with an aqueous 20% formaldehyde solution and held for 7 days in a 10% aqueous solution of the same active ingredient. During the first phase of the experiment, small specimens of animal tissue previously fixed in formaldehyde were distributed in vials with different concentrations of formaldehyde, with or without 30% sodium chloride solution, a group containing only 30% sodium chloride, and a control group containing only water. During this phase, no contamination was observed in any specimen containing 30% sodium chloride solution, whether alone or in combination with different concentrations of formaldehyde. In the second phase of the experiment, the 30% sodium chloride solution, found to be optimal in the first phase of the experiment, was tested for its long-term preservation properties. For a period of 5 years, the preserved specimens were evaluated three times a week for visual contamination, odors, and changes in color and texture. There was no visual contamination or decay found in any specimen. Furthermore, no strange odors, or changes in color or softness were noted. The 30% sodium chloride solution was determined to be effective in the preservation of anatomic specimens previously fixed in formaldehyde. © 2014 Anatomical Society.

Treatment of low and intermediate aqueous waste containing Cs-137 by chemical precipitation

International Nuclear Information System (INIS)

Valdezco, E.M.; Marcelo, E.A.; Alamares, A.L.; Junio, J.B.; Dela Cruz, J.M.

1996-01-01

The use of radioactive materials in various applications has been increasing since its introduction in the early sixties. The Philippine Nuclear Research Institute has established a centralized facility for treating radioactive wastes i.e. aqueous wastes with assistance from the International Atomic Energy Agency - Technical Cooperation Programme. Liquid wastes containing Cs-137 are generated from aqueous wastes containing Cs-137 by nickel ferrocyanide precipitation will be presented. The aim of this study is to investigate the efficiency treatment in removing Cs-137 from an aqueous effluent. Actual aqueous wastes known to contain Cs-137 were used in the experiments. Low cost and simple nickel ferrocyanide precipitation method with the aid of a flocculant has been selected for the separation of Cs-137 from low and intermediate aqueous waste. By varying the chemical dosage added into the aqueous waste, different decontamination factors were obtained. Hence, the optimum dosage of the chemicals that give the highest decontamination factor can be determined. (author)

Method of purification of solutions containing plutonium and/or neptunium by plutonium and/or neptunium separation

Energy Technology Data Exchange (ETDEWEB)

Herz, D; Kankura, R; Wenzel, U

1975-03-27

Aqueous solutions containing, amongst other radiation sources, 10/sup -2/ to 10/sup -7/ mol per litre Pu and/or Np - especially aqueous solutions produced when reprocessing fuel elements, in particular of HTR reactors, e.g. according to the Thorex process - can be cleaned from the two metals without much expenditure by using a separating column: determination of the H/sup +/ ion concentration (0.5-6 mol/litre solution), addition of a stabilizing agent (NaNO/sub 2/ or Fe (NH/sub 2/SO/sub 3/)/sub 2/) and passage across a separating column in which the granulate charge is wetted with a long-chain alkylamine (e.g. trioctylamine) which retains the metal. The production of a charge (of Voltalef UF 300) is described. The process may also be carried out continuously.

Behavior of Am in acidic and basic solutions of potassium ferri/ferrocyanide

International Nuclear Information System (INIS)

Kulyako, Yu.M.; Trofimov, T.I.; Malikov, D.A.; Lebedev, I.A.; Myasoedov, B.F.

1994-01-01

The behavior of Am in acidic and basic solutions containing the Fe(CN) 3- 6 /Fe(CN) 4- 6 redox system is studied. In mineral acids, K 3 Fe(CN) 6 and Am(III) form the poorly soluble compound AmFe(CN) 6 , which with time undergoes a change owing to radiolytic reduction of Fe(CN) 3- 6 to Fe(CN) 4- 6 . In basic solutions of K 3 Fe(CN) 6 , Am(III) is oxidized to AmO + 2 , forming the soluble complex (AmO 2 ) 3 Fe(CN) 6 , which gradually decomposes to produce the solid double hydroxide Na 2 AmO 2 (OH) 3 ·nH 2 O. An Am(IV) hydroxide is formed if [Am] and [K 3 Fe(CN) 6 ] are equal

Adsorption of Polycyclic Aromatic Hydrocarbons (PAHS from Aqueous Solutions on Different Sorbents

Directory of Open Access Journals (Sweden)

Smol Marzena

2014-12-01

Full Text Available This paper presents the results of the possibility and effectiveness of PAHs removal from a model aqueous solution, during the sorption on the selected sorbents. Six PAHs (naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene listed by EPA for the analysis in the environmental samples were determined. Model aqueous solution was prepared with RESTEK 610 mix PAHs standard. After the sorption process, decrease in the concentration of individual hydrocarbons was observed. The removal percentage was dependent on the type of sorbent (quartz sand, mineral sorbent, activated carbon. The highest efficiency (98.1% was observed for activated carbon.. The results shows that the sorption processes can be used in aqueous solutions treatment procedures.

Assembly of DNA Architectures in a Non-Aqueous Solution

Directory of Open Access Journals (Sweden)

Thomas J. Proctor

2012-08-01

Full Text Available In the present work, the procedures for the creation of self-assembled DNA nanostructures in aqueous and non-aqueous media are described. DNA-Surfactant complex formation renders the DNA soluble in organic solvents offering an exciting way to bridge the transition of DNA origami materials electronics applications. The DNA retains its structural features, and these unique geometries provide an interesting candidate for future electronics and nanofabrication applications with potential for new properties. The DNA architectures were first assembled under aqueous conditions, and then characterized in solution (using circular dichroism (CD spectroscopy and on the surface (using atomic force microscopy (AFM. Following aqueous assembly, the DNA nanostructures were transitioned to a non-aqueous environment, where butanol was chosen for optical compatibility and thermal properties. The retention of DNA hierarchical structure and thermal stability in non-aqueous conditions were confirmed via CD spectroscopy. The formation and characterization of these higher order DNA-surfactant complexes is described in this paper.

Molybdenum: the element and aqueous solution chemistry

International Nuclear Information System (INIS)

Sykes, A.G.

1987-01-01

This chapter on the chemistry of the coordination compounds of molybdenum concentrates on the element itself, its recovery from ores and its use in the manufacture of steels. Most of the chapter is devoted to the aqueous solution chemistry of molybdenum in oxidation states II, III and IV. (UK)

CdSe nanoparticles grown via radiolytic methods in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Singh, Shalini [Radiation and Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Rath, M.C., E-mail: madhab@barc.gov.i [Radiation and Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Singh, A.K. [Radiation and Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Mukherjee, T. [Chemistry Group, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Jayakumar, O.D.; Tyagi, A.K. [Chemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Sarkar, S.K. [Radiation and Photochemistry Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2011-06-15

Cadmium selenide, CdSe, nanoparticles have been synthesized in aqueous solution containing equimolar ammoniated CdSO{sub 4} and Na{sub 2}SeSO{sub 3} as the starting materials without any capping agents, using gamma and electron beam irradiation under a reducing condition. The radiolytic processes occurring in water result in the formation of CdSe nanoparticles through the reactions mediated by hydrated electrons, e{sub aq}{sup -}. TEM measurements revealed that the CdSe nanoparticles were found to exist in agglomerates of dimension of about 100 nm, consisting of primary nanoparticles of dimensions within 5 nm. The as-grown nanoparticles were of cubic crystalline phase as supported by the XRD measurements. These bare CdSe nanoparticles exhibit room temperature ferromagnetic (RTFM) behavior. However, the RTFM behavior was found to be 30% higher in the case of CdSe nanoparticles prepared on electron beam irradiation as compared to those obtained by gamma irradiation, which was attributed to their relatively smaller size (2-3 nm) and disordered structures as compared to those obtained in the later case (3-5 nm). -- Research highlights: {yields} CdSe nanoparticles could be synthesized in aqueous solutions containing equimolar ammoniated CdSO{sub 4} and Na{sub 2}SeSO{sub 3} as the starting materials using gamma and electron beam irradiation under a reducing condition. {yields} CdSe nanoparticles were found to exist in agglomerates of dimension of about 100 nm, consisting of primary nanoparticles of dimensions within 5 nm. {yields} CdSe nanoparticles exhibit room temperature ferromagnetic (RTFM) behavior. {yields} The RTFM behavior was found to be 30% higher in the case of CdSe nanoparticles prepared on electron beam irradiation as compared to those obtained by gamma irradiation.

Synthesis of sub-millimeter calcite from aqueous solution

Science.gov (United States)

Reimi, M. A.; Morrison, J. M.; Burns, P. C.

2011-12-01

A novel aqueous synthesis that leads to the formation of calcite (CaCO3) crystals, up to 500μm in diameter, will be used to facilitate the study of contaminant transport in aqueous environmental systems. Existing processes tend to be complicated and often yield nanometer-sized or amorphous CaCO3. The synthesis method presented here, which involves slow mixing of concentrated solutions of CaCl2 ¬and (NH4)2CO3, produces single crystals of rhombohedral calcite in 2 to 4 days. Variations on the experimental method, including changes in pH and solution concentration, were explored to optimize the synthesis. Scanning Electron Microscope images show the differences in size and purity observed when the crystals are grown at pH values ranging from 2 to 6. The crystals grown from solutions of pH 2 were large (up to 500 micrometers in diameter) with minimal polycrystalline calcium carbonate, while crystals grown from solutions with pH values beyond 4 were smaller (up to 100 micrometers in diameter) with significant polycrystalline calcium carbonate. The synthesis method, materials characterization, and use in future actinide contaminant studies will be discussed.

Acid-base equilibrium in aqueous solutions of 1,3-dimethylbarbituric acid as studied by 13C NMR spectroscopy

Science.gov (United States)

Gryff-Keller, A.; Kraska-Dziadecka, A.

2011-12-01

13C NMR spectra of 1,3-dimethylbarbituric acid in aqueous solutions of various acidities and for various solute concentrations have been recorded and interpreted. The spectra recorded at pH = 2 and below contain the signals of the neutral solute molecule exclusively, while the ones recorded at pH = 7 and above only the signals of the appropriate anion, which has been confirmed by theoretical GIAO-DFT calculations. The signals in the spectra recorded for solutions of pH pH variation have been observed for the parent barbituric acid.

The reaction of Cs{sub 2}[Tc(NO)F{sub 5}] with BF{sub 3} in acetonitrile. Formation and structure of [{Tc(NO)(CH_3CN)_4}{sub 2}(μ-F)](BF{sub 4}){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Balasekaran, Samundeeswari Mariappan [Institute of Chemistry and Biochemistry, Freie Universitaet Berlin (Germany); Department of Chemistry, University of Nevada, Las Vegas, NV (United States); Hagenbach, Adelheid; Spandl, Johann; Abram, Ulrich [Institute of Chemistry and Biochemistry, Freie Universitaet Berlin (Germany)

2017-10-04

The deep blue, paramagnetic Cs{sub 2}[Tc{sup II}(NO)F{sub 5}] is formed during reactions of pertechnetate, acetohydroxamic acid, and CsF in aqueous HF. A reaction of Cs{sub 2}[Tc(NO)F{sub 5}] with BF{sub 3}.MeOH in acetonitrile gives yellow blocks of the fluorido-bridged dimer [{Tc"I(NO)(CH_3CN)_4}{sub 2}F](BF{sub 4}){sub 3}. The compound is stable as solid and in acetonitrile solutions. The complex cation contains a bent μ-F{sup -} ligand and two linear nitrosyl groups. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Measuring the density and viscosity of H2S-loaded aqueous methyldiethanolamine solution

International Nuclear Information System (INIS)

Shokouhi, Mohammad; Ahmadi, Reza

2016-01-01

Highlights: • Measurement solubility of H 2 S in 46.78 mass% MDEA aqueous solutions. • Measurement density of H 2 S loaded of MDEA aqueous solution. • Measurement viscosity of H 2 S loaded of MDEA aqueous solution. • Correlation of the density and viscosity of H 2 S loaded of MDEA aqueous solution using modified setchenow equation. - Abstract: The density and viscosity of H 2 S-loaded aqueous 46.78 mass% methyldiethanolamine solution were experimentally measured accompanied with the solubility of H 2 S at temperatures (313.15, 328.15 and 343.15) K, pressures from vapor pressure of fresh solution up to 1.0 MPa and loadings up to 1.00 mol of H 2 S per 1 mol of amine. All experimental trials have been carried out using the new setup developed in our laboratory. It was observed that both density and viscosity of mixtures decrease by increasing temperature and density increase by increasing acid gas solubility (loading) by about 4.7%, whereas viscosity has a complicated behavior with H 2 S solubility. Viscosity decreases by increasing acid gas solubility (loading) at 313.15 K by about 20.6% and at 328.15 K by about 15.0%, but it is comparable at 343.15 K in terms of H 2 S solubility. Finally, the experimental density and viscosity data correlated using Modified Setchenow equation.

Effect of gamma irradiation on viscosity of aqueous solutions of some natural polymers

International Nuclear Information System (INIS)

Nguyen Tan Man; Truong Thi Hanh; Le Quang Luan; Le Hai; Nguyen Quoc Hien

2000-01-01

Effect of gamma irradiation on viscosity of aqueous solution of alginate and carbon xylmethyl cellulose (CMC) irradiated in solid state has been carried out. the viscosity of aqueous solution of alginate and CMC decreased remarkably with increasing dose and the viscosity of 2% solution of above polymers irradiated at 50 kGy was about 100 times lower than the original one. (author)

On the mechanism of dechlorination of polychlorinated biphenyls (PCBs) induced by electron beam irradiation in aqueous and aqueous micellar solutions, transformer oil, and sediment

International Nuclear Information System (INIS)

Chaychian, M.; Silverman, J.; Al-Sheirkhly, M.

2011-01-01

Complete text of publication follows. The widespread release of PCBs into the environment presents a serious problem due to their persistence and toxicity. Ionizing radiation, such as gamma rays and high-energy electron beam, is remarkably effective in dechlorinating PCBs into biphenyls. The kinetics of the reductive dechlorination of PCBs in aqueous and aqueous micellar solutions and in transformer oil is being studied by pulse radiolysis and steady-state radiolysis. In aqueous micellar solutions, dichlori-, tetrachloro-, and decachlorobiphenyl congeners were solubilized in water using a commercially available non-ionic surfactant, Triton X-100, and subsequently pulse irradiated by electron accelerator using optical detection method. The reaction rate constant between decachlorobiphenyl and aqueous electrons e aq ·- , and Triton with e aq ·- in the 2% Triton solution, were measured as 2.6 x 10 9 Lmol -1 s -1 and 1.2 x 10 7 Lmol -1 s -1 , respectively. We have also measured in aqueous solutions, the reaction rate constant of e aq ·- with dichlorobiphenyl as 3.8 x 10 9 Lmol -1 s -1 . In aqueous-propanol, the reaction rate constants of e aq ·- with dichlorobiphenyl, tetrachlorobiphenyl, and dechachlorobiphenyl are 2 x 10 9 Lmol -1 s -1 , 3 x 10 9 Lmol -1 s -1 , and 7 x 10 9 Lmol -1 s -1 , respectively. In addition to the presence of PCBs as high-dielectric component, transformer oil contains many aromatic hydrocarbons; the most abundant being biphenyl, fluorine, and phenanthrene. Solvated electrons formed by irradiation of the oil react either with PCB to lead to dechlorination or with the aromatic hydrocarbons present in the oil to form radical anions. These species are shown to transfer an electron to chlorinated biphenyls relative rapidly, leading to dechlorination. The rate constants for several such reactions, determined in 2-propanol solutions, are in the range of 10 7 - 10 8 Lmol -1 s -1 . These rapid reactions explain why PCB can be dechlorinated in oil

Spectrophotometric investigation of the hetero-association of Caffeine and thiazine dye in aqueous solution

Science.gov (United States)

Bolotin, P. A.; Baranovsky, S. F.; Evstigneev, M. P.

2006-06-01

The self-association of thiazine dye, Methylene Blue (MB), and its hetero-association with Caffeine (CAF), were studied in aqueous solution by means of spectrophotometry in the visible range of spectrum. Concentration and temperature dependences of molar absorption of the interacting molecules were used to analyse dynamic equilibrium in solution in terms of two-component model of molecular hetero-association. The magnitudes of equilibrium dimerization and hetero-association constants as well as thermodynamic parameters, enthalpy and entropy, were determined. The calculation of the fraction of different types of associates in the mixed solution, containing Methylene Blue and Caffeine, was done. It was concluded that the hetero-association of Methylene Blue and Caffeine molecules results in lower effective concentration of the dye in solution, which may account for the alteration of its biological activity.

Quenching characteristics of bathocuproinedisulfonic acid, disodium salt in aqueous solution and copper sulfate plating solution

Science.gov (United States)

Koga, Toshiaki; Hirakawa, Chieko; Takeshita, Michinori; Terasaki, Nao

2018-04-01

Bathocuproinedisulfonic acid, disodium salt (BCS) is generally used to detect Cu(I) through a color reaction. We newly found BCS fluorescence in the visible blue region in an aqueous solution. However, the fluorescence mechanism of BCS is not well known, so we should investigate its fundamental information. We confirmed that the characteristics of fluorescence are highly dependent on the molecular concentration and solvent properties. In particular, owing to the presence of the copper compound, the fluorescence intensity extremely decreases. By fluorescence quenching, we observed that a copper compound concentration of 10-6 mol/L or less could easily be measured in an aqueous solution. We also observed BCS fluorescence in copper sulfate plating solution and the possibility of detecting monovalent copper by fluorescence reabsorption.

The effect of temperature on radiolysis of iodide ion diluted aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Gorbovitskaya, T; Tiliks, J [Latvia Univ., Lab. of Radiation Chemistry, Riga (Latvia)

1996-12-01

To investigate the radiolysis of iodine containing aqueous solutions a flow type facility (ITF) has a possibility to irradiate aqueous solutions in the steel vessel with {sup 60}Co {gamma}-rays and continuously (on line) to analyze the products of radiolysis both in liquid and in gaseous phases. By means of ITF the formation of I{sub ox} (I{sub 2} + I{sub 3}{sup -} + HOI), IO{sub 3}{sup -}, H{sub 2}O{sub 2} was studied in 10{sup -5} - 10{sup -3} mol/dm{sup 3} CsI aqueous solutions by their radiolysis at dose rate 4.5 kGv/h for six hours in region of temperatures from 313 to 404 K. Some experiments in glass ampoules were also performed. The steady-state concentrations of I{sub ox} and IO{sub 3}{sup -} decreased with increasing temperature as linear function of inverted temperature. The effect decreased with decreasing concentration of iodide ion. As the result, at high temperatures (T{>=}380 K) the steady-state concentration of I{sub ox} does not depend essentially on the iodide ion initial concentration. Molecular iodine (I{sub 2}) released from the solution was the main radiolysis product in gaseous phase. Its steady-state concentration increased with increasing temperature because of iodine solubility in the water and decreased at the same time because the radiolytic iodine concentrations decreased. Therefore the most volatility of irradiated 10{sup -3} and 10{sup -4}M CsI solutions was observed at the temperature about 350 K. The volatility of 10{sup -5}M solutions gradually decreased with increasing temperature. The experimental data were explained on the base of the hypothesis that the reaction between I{sub 2} and radiolytic H{sub 2}O{sub 2} was the limit one determining the temperature dependence of I{sub ox} and IO{sub 3}{sup -}steady-state concentrations. Its activation energy was estimated to be 27,5 kcal.mol{sup -1}. The temperature dependence for reaction (IO{sup -} + H{sub 2}O{sub 2}) was also estimated. (author) 8 figs., 1 tab., 17 refs.

Effect of pH on the corrosion behaviour of SUS321 in the ammonia aqueous solution

International Nuclear Information System (INIS)

Park, Sang Yoon; Jeong, Y. H.; Baek, J. H.; Choi, B. K.; Lee, M. H.; Choi, B. S.; Yoon, J. H.; Lee, D. J.

2003-02-01

The corrosion characteristics of SUS321 for pressure vessel of SMART in pure water, ammonia aqueous solutions of pH 8.5 ∼ 11.5 at 300 .deg. C were evaluated by using static autoclaves. SUS321 specimen in the high temperature ammonia aqueous solution has weight gain or loss by the 4 reactions. And it depends on the refreshing period of the aqueous solution. So additional experiments by recirculating loop system were required to evaluate the corrosion behaviour of SUS321 in the ammonia aqueous solution

Pitting corrosion of zirconium in aqueous solution

International Nuclear Information System (INIS)

El Shayeb, H.A.; Abd El Wahab, F.M.; Abd Elk Meguid, E.A.

1994-01-01

The open circuit potentials of the Zr electrode are followed as a function of time in various aqueous solutions till attainment of steady state values.The results are discussed on the basis of oxide film thickening and repair. Pitting corrosion of Zr was examined in chloride solutions using the potentiodynamic technique. The effect of some inorganic and organic additives was also investigated for inhibiting the pitting corrosion of Zr and the relative performance is presented and discussed. (author). 21 refs., 6 figs., 1 tab

Stabilizers of edaravone aqueous solution and their action mechanisms. 2. Glutathione

OpenAIRE

Tanaka, Masahiko; Motomiya, Satsuki; Fujisawa, Akio; Yamamoto, Yorihiro

2017-01-01

Edaravone (3-methyl-1-phenyl-2-pyrazolin-5-one) has garnered attention since its approval for amyotrophic lateral sclerosis in Japan (2015) and the United States (2017). Edaravone is administered intravenously, and as such, is distributed in the form of an aqueous solution. However, aqueous solutions of edaravone are very unstable because they present as edaravone anions, which become edaravone radicals when the anion donates an electron to free radicals including oxygen. In this study, gluta...

Kinetics of the decomposition and the estimation of the stability of 10% aqueous and non-aqueous hydrogen peroxide solutions

Directory of Open Access Journals (Sweden)

Zun Maria

2014-12-01

Full Text Available In this study, the stability of 10% hydrogen peroxide aqueous and non-aqueous solutions with the addition of 6% (w/w of urea was evaluated. The solutions were stored at 20°C, 30°C and 40°C, and the decomposition of hydrogen peroxide proceeded according to first-order kinetics. With the addition of the urea in the solutions, the decomposition rate constant increased and the activation energy decreased. The temperature of storage also affected the decomposition of substance, however, 10% hydrogen peroxide solutions prepared in PEG-300, and stabilized with the addition of 6% (w/w of urea had the best constancy.

Paracetamol degradation in aqueous solution by non-thermal plasma

Science.gov (United States)

Baloul, Yasmine; Aubry, Olivier; Rabat, Hervé; Colas, Cyril; Maunit, Benoît; Hong, Dunpin

2017-08-01

This study deals with paracetamol degradation in water using a non-thermal plasma (NTP) created by a dielectric barrier discharge (DBD). The effects of the NTP operating conditions on the degradation were studied, showing that the treatment efficiency of the process was highly dependent on the electrical parameters and working gas composition in the reactor containing the aqueous solution. A conversion rate higher than 99% was reached with an energy yield of 12 g/kWh. High resolution mass spectrometry (HRMS) measurements showed that the main species produced in water during the process were nitrogen compounds, carboxylic acids and aromatic compounds. Contribution to the topical issue "The 15th International Symposium on High Pressure Low Temperature Plasma Chemistry (HAKONE XV)", edited by Nicolas Gherardi and Tomáš Hoder

Antimicrobial activity of copper against organisms in aqueous solution: a case for copper-based water pipelines in hospitals?

Science.gov (United States)

Cervantes, Hilda I; Alvarez, Jose A; Muñoz, Juan M; Arreguín, Virginia; Mosqueda, Juan L; Macías, Alejandro E

2013-12-01

An association exists between water of poor quality and health care-associated infections. Copper shows microbiocidal action on dry surfaces; it is necessary to evaluate its antimicrobial effect against organisms in aqueous solution. The objective was to determine the in vitro antimicrobial activity of copper against common nosocomial pathogens in aqueous solution. Copper and polyvinyl chloride containers were used. Glass was used as control material. Fourteen organisms isolated from hospital-acquired infections, and 3 control strains were tested. Inocula were prepared by direct suspension of colonies in saline solution and water in each container tested. Bacterial counts in colony-forming units (CFU)/mL were determined at the beginning of the experiment; at 30 minutes; and at 1, 2, 24, and 48 hours. Organisms in glass and polyvinyl chloride remained viable until the end of the experiment. Organisms in copper showed a reduction from more than 100,000 CFU/mL to 0 CFU/mL within the first 2 hours of contact (F > 4.29, P water for human use, particularly in hospitals. Copyright © 2013 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Mosby, Inc. All rights reserved.

Thermochemistry of the Dissolution of Dipeptides Containing DL-α-Alanine in Aqueous Solutions of Sodium Dodecyl Sulfate at 298.15 K

Science.gov (United States)

Smirnov, V. I.; Badelin, V. G.

2018-05-01

Enthalpies of the dissolution of DL-α-alanylglycine (AlaGly), DL-α-alanyl-DL-α-alanine (AlaAla), DL-α-alanyl-DL-α-valine (AlaVal), and DL-α-alanyl-DL-norleucine (AlaNln) in an aqueous solution of sodium dodecyl sulfate (SDS) at SDS concentration of m = 0-0.07 mol kg-1 and temperature T = 298.15 K are measured via calorimetry. The standard values of the enthalpy of dissolution (Δsol H m ) and the transfer of dipeptides (Δtr H m ) from water to aqueous SDS solutions are calculated using the experimental data. The dependences of Δsol H m and Δtr H m the SDS concentration at a constant concentration of dipeptide are established. Thermochemical characteristics of the transfer of AlaGly, AlaAla, AlaVal, and AlaNln in the investigated range of SDS concentrations are compared. The results are interpreted by considering ion-ion, ion-polar, and hydrophobic-hydrophobic interactions between SDS and dipeptide molecules.

Interaction of silicon nanoparticles with the molecules of bovine serum albumin in aqueous solutions

International Nuclear Information System (INIS)

Anenkova, K A; Sergeeva, I A; Petrova, G P; Fedorova, K V; Osminkina, L A; Timoshenko, Viktor Yu

2011-01-01

Using the method of photon-correlation spectroscopy, the coefficient of translational diffusion D t and the hydrodynamic radius R of the particles in aqueous solutions of the bovine serum albumin, containing silicon nanoparticles, are determined. The character of the dependence of these parameters on the concentration of the protein indicates the absence of interaction between the studied particles in the chosen range of albumin concentrations 0.2 - 1.0 mg mL -1 . (optical technologies in biophysics and medicine)

Removal of Nickel from Aqueous Solution by Hard-Shell Pistachios

Directory of Open Access Journals (Sweden)

Shayan Shamohammadi

2013-08-01

Full Text Available Nickel is one of the heavy metals which commonly can be found in industrial wastewater. Many studies have been done on agricultural waste for the removal of nickel from aqueous solutions. The purpose of this study is to identify hard-shell pistachios as a local attraction for removal of nickel from aqueous solution. Nickel adsorption isotherm models are studied using shell pistachios. Pistachio shell was chosen which its particle size is between 800-600 microns. The stock solution of nickel ions was prepared mixing nickel nitrate with distilled water. The results showed that the maximum absorption efficiency occurs (73.3% at pH=8. Also, it was shown that with increasing adsorbent dose, equilibrium time decreased within constant concentration. Examination of uptake isotherm models showed that models of Freundlich, BET, Radke-Praunitz, Redlich-Peterson and Sips describe data in 97% level of confidence well,  however Freundlich and Sips isotherm models has the lowest error factor 0.10597 and 0/10598 respectively and the highest correlation coefficient (0.9785. Comparison of adsorbent capacity within removal of nickel from aqueous solution shows that Pistachio shell with special absorbent surface of 1.7 m2/g and uptake capacity of 0.3984 mg/g is proper than adsorbents of Kaolinite, Bagasse, sludge-ash.

Molecular mechanism of the viscosity of aqueous glucose solutions

Science.gov (United States)

Bulavin, L. A.; Zabashta, Yu. F.; Khlopov, A. M.; Khorol'skii, A. V.

2017-01-01

Experimental relations are obtained for the viscosity of aqueous glucose solutions in the temperature range of 10-80°C and concentration range 0.01-2.5%. It is found that the concentration dependence of fluidity is linear when the concentration is higher than a certain value and varies at different temperatures. The existence of such a dependence indicates that the mobilities of solvent and solute molecules are independent of the concentration of solutions. This assumption is used to construct a theoretical model, in which the structure of an aqueous glucose solution is presented as a combination of two weakly interacting networks formed by hydrogen bonds between water molecules and between glucose molecules. Theoretical relations are obtained using this model of network solution structure for the concentration and temperature dependence of solution viscosity. Experimental data are used to calculate the activation energies for water ( U w = 3.0 × 10-20 J) and glucose molecules ( U g = 2.8 × 10-20 J). It is shown that the viscosity of a solution in such a network structure is governed by the Brownian motion of solitons along the chains of hydrogen bonds. The weak interaction between networks results in the contributions to solution fluidity made by the motion of solitons in both of them being almost independent.

Preparation of novel polysulfone capsules containing zirconium phosphate and their properties for Pb{sup 2+} removal from aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Ma Xiaojie [College of Chemistry and Chemical Engineering, State Key Laboratory of Applied Organic Chemistry, College of Resources and Environment, Institute of Biochemical Engineering and Environmental Technology, Lanzhou University, Lanzhou 730000 (China); Li Yanfeng, E-mail: liyf@lzu.edu.cn [College of Chemistry and Chemical Engineering, State Key Laboratory of Applied Organic Chemistry, College of Resources and Environment, Institute of Biochemical Engineering and Environmental Technology, Lanzhou University, Lanzhou 730000 (China); Li Xiaoli; Yang Liuqing [College of Chemistry and Chemical Engineering, State Key Laboratory of Applied Organic Chemistry, College of Resources and Environment, Institute of Biochemical Engineering and Environmental Technology, Lanzhou University, Lanzhou 730000 (China); Wang Xueyan [Yantai Professional School of Automobile Engineering, Yantai 265500 (China)

2011-04-15

Zirconium phosphate (ZrP) was immobilized by microencapsulation process of polysulfone (PSF) to form the polysulfone capsules containing ZrP (PSF-ZrP capsules) successfully by using phase inversion precipitation technique, and the PSF-ZrP was employed as capsules adsorbents to remove Pb{sup 2+} presented in aqueous solution. The result shows that an encapsulation capacity of 50% (mass ratio, PSF: ZrP = 1:1) should be the optimal proportion of ZrP encapsulated with PSF. The characterization of the macroscopical and microcosmic physical properties of the resulting PSF-ZrP capsules was carried out by the DTA-TG, XRD, BET and SEM. Meanwhile, the adsorption properties of the PSF-ZrP capsules for Pb{sup 2+} were investigated by batch methods. It was found that the adsorption of the PSF-ZrP capsules for Pb{sup 2+} would be pH dependent due to the ion-exchange mechanism, and the uptake of Pb{sup 2+} was slightly influenced with the concentration of coexisting cations (Na{sup +}, K{sup +}) in a low range. Furthermore, the calculated thermodynamics parameters exhibit that the nature of the adsorption process is spontaneous and exothermic. After six times of adsorption-regeneration cycles, no significant loss of adsorption capacity was observed, indicating the good stability of the PSF-ZrP capsules. Consequently, the PSF-ZrP capsules in this work can provide a potential application for treatment process of Pb{sup 2+}-containing wastewater.

Ion from Aqueous Solution using Magnetite, Activated Carbon

African Journals Online (AJOL)

ADOWIE PERE

Thermodynamic studies on Adsorption of lead (II) Ion from Aqueous Solution using. Magnetite ... process industries and agricultural activities, which tends to ... osmosis. These processes are however, not economically feasible for small scale industries .... Freundlich coefficient. ..... from binary component system, Beni-suef.

Analysis and modeling of alkali halide aqueous solutions

DEFF Research Database (Denmark)

Kim, Sun Hyung; Anantpinijwatna, Amata; Kang, Jeong Won

2016-01-01

on calculations for various electrolyte properties of alkali halide aqueous solutions such as mean ionic activity coefficients, osmotic coefficients, and salt solubilities. The model covers highly nonideal electrolyte systems such as lithium chloride, lithium bromide and lithium iodide, that is, systems...

Photoionization of rhodamine dyes adsorbed at the aqueous solution surfaces investigated by synchrotron radiation

International Nuclear Information System (INIS)

Seno, Koichiro; Ishioka, Toshio; Harata, Akira; Hatano, Yoshihiko

2002-01-01

Photoionization spectroscopy using synchrotron radiation as a photon source was applied to the aqueous solution surfaces of rhodamine B (RhB), rhodamine 6G (Rh6G), and rhodamine 101 (Rh101) with their concentration of 0-100 μmol dm -3 . Synchrotron radiation was irradiated upon the solution surface between two electrodes in the photon energy range of 4-7 eV, and photoionization current was measured by a pico-ammeter. The photocurrent for each of the rhodamine aqueous solution surface showed an increase with the photon energy above a threshold photon energy. The photoionization threshold of RhB at the aqueous solution surface was 5.6 eV, which was smaller than that in the gas phase. The intensity of photoionization current of Rh6G was smaller than that of RhB or Rh101. Photoionization processes and the state of Rhodamine dye molecules at the aqueous solution surface were discussed in connection with results of surface tension measurements. (author)

Use of cationites for separation of transplutonium elements from other elements from aqueous and aqua-alcohol solutions of hydrochloric and nitric acids

International Nuclear Information System (INIS)

Guseva, L.I.; Tikhomirova, G.S.

1984-01-01

The behaviour of Am, Cm, Pu and certain fragment elements (Cs, Sr, Y, Zr, Nb, Ru, Eu) on cationite dauex-50 in aqueous and aqueous-alcohol solutions of HCl and HNO 3 has been studied. Dependences of distribution coefficients and separation factors of the elements on the acid concentration and alcohol content in the solutions are presented. The sorption of TPE by cationite from HCl and HNO 3 solutions in the presence of alcohol is shown to increase over the range of concentrations studied (from 0.5 mol/L to 4-5 mol/L), which is explained by the salting-out effect of alcohol. The distribution coefficients of TPE in the solutions, containing >= 50% alcohol, constitute >= 10 2 . The distribution coefficients of the fragment elements in the presence of alcohol also increase, but to a considerably lesser extent, which results in a better separation. The study of the washing-out curves has shown that, to separate TPE from fragment elements on cationites, both HCl and HNO 3 solutions can be used, at that, in the case of aqueous solutions a better separation is attained at acid concentration, equal to 1 mol/L, and in the case of eluating by aqueous-alcohol solutions a good separation is achieved at hig-her concentrations of the acids as well

The Use of Sonochemical Technology for Cyanide Removal from Aqueous Solutions in the Presence of Hydrogen Peroxide

Directory of Open Access Journals (Sweden)

Reza Shokoohi

2011-10-01

Full Text Available Cyanide is a highly toxic species that found mostly in industrial effluents such as electroplating, metal mining, metallurgy and metal cleaning processes. Discharge of it into the enviroment causes very health impact. Purpose of this study was, determination of sonochemical technology for cyanide removal from aqueous solutions in the presence of hydrogen peroxide. In this study, a productive set of 500w power ultresoun waves with two frequencies 35 kHz and 130 kHz were used. Experiments were performed using different initial ratio CN-/H2O2 1/1, 1/3 and 1/5 and at initial cyanide concentrations varying from 2.5 to 75 mg/L. The effects of parameters such as pH, time and initial cyanide concentration on the sonochemical degradation have been studied. The results of the study showed that the maximom removal efficiency of cyanide was achieved 85% by sonochemical technology at frequency of 130 kHz, during of 90 min, at pH of 11, at initial cyanide concentration of  2.5 mg/l and with initial ratio of CN-/H2O2 1/5. it was also found the rates of cyanide degradation under different conditions were quite low, and also the rate of cyanide degradation was high at first but later substantially reduced. The efficiency of cyanide removal had direct relationship with pH, frequency, hydrogen peroxide concentration and time ,and it had reverse relationship with cyanide concentration.

Sound velocity in potassium hydroxide aqueous solution

International Nuclear Information System (INIS)

Tsapuryan, Kh.D.; Aleksandrov, A.A.; Kochetkov, A.I.

1992-01-01

Measurements of ultrasonic velocities in potassium hydroxide aqueous solutions are carried out within the frames of studies on improvement of water chemistry in NPP cooling systems. Method of echo pulses superposition with acoustic path length of 41.447 mm is used for measurements. The measurements are performed at 2.6 MHz frequency. Complex temperature dependence of ultrasonic velocity is determined. Ultrasonic velocity dependence on pressure is close to linear one. The formula for calculation of thermodynamic properties of the studied solutions on the basis of experimental data obtained is proposed

Hydrate phase equilibria of CO2+N2+aqueous solution of THF, TBAB or TBAF system

DEFF Research Database (Denmark)

Sfaxi, Imen Ben Attouche; Durand, Isabelle; Lugo, Rafael

2014-01-01

We report hydrate dissociation conditions of CO2 (15 and 30mol%)+N2 (85 and 70mol%) in the presence of aqueous solutions of THF, TBAB or TBAF. The concentrations of TBAB and TBAF in the aqueous solutions are 5wt% and 9wt% while THF concentration in aqueous solution is 3mol%. Two different experim...

Influence of formulation and processing variables on properties of itraconazole nanoparticles made by advanced evaporative precipitation into aqueous solution.

Science.gov (United States)

Bosselmann, Stephanie; Nagao, Masao; Chow, Keat T; Williams, Robert O

2012-09-01

Nanoparticles, of the poorly water-soluble drug, itraconazole (ITZ), were produced by the Advanced Evaporative Precipitation into Aqueous Solution process (Advanced EPAS). This process combines emulsion templating and EPAS processing to provide improved control over the size distribution of precipitated particles. Specifically, oil-in-water emulsions containing the drug and suitable stabilizers are sprayed into a heated aqueous solution to induce precipitation of the drug in form of nanoparticles. The influence of processing parameters (temperature and volume of the heated aqueous solution; type of nozzle) and formulation aspects (stabilizer concentrations; total solid concentrations) on the size of suspended ITZ particles, as determined by laser diffraction, was investigated. Furthermore, freeze-dried ITZ nanoparticles were evaluated regarding their morphology, crystallinity, redispersibility, and dissolution behavior. Results indicate that a robust precipitation process was developed such that size distribution of dispersed nanoparticles was shown to be largely independent across the different processing and formulation parameters. Freeze-drying of colloidal dispersions resulted in micron-sized agglomerates composed of spherical, sub-300-nm particles characterized by reduced crystallinity and high ITZ potencies of up to 94% (w/w). The use of sucrose prevented particle agglomeration and resulted in powders that were readily reconstituted and reached high and sustained supersaturation levels upon dissolution in aqueous media.

Preliminary study on the photoproduction of hydroxyl radicals in aqueous solution with Aldrich humic acid, algae and Fe(III) under high-pressure mercury lamp irradiation.

Science.gov (United States)

Liu, Xianli; Xu, Dong; Wu, Feng; Liao, Zhenhuan; Liu, Jiantong; Deng, Nansheng

2004-03-01

Under a high-pressure mercury lamp (HPML) and using an exposure time of 4 h, the photoproduction of hydroxyl radicals (*OH) could be induced in an aqueous solution containing humic acid (HA). Hydroxyl radicals were determined by high-performance liquid chromatography using benzene as a probe. The results showed that *OH photoproduction increased from 1.80 to 2.74 microM by increasing the HA concentration from 10 to 40 mg L(-1) at an exposure time of 4 h (pH 6.5). Hydroxyl radical photoproduction in aqueous solutions of HA containing algae was greater than that in the aqueous solutions of HA without algae. The photoproduction of *OH in the HA solution with Fe(III) was greater than that of the solution without Fe(III) at pH ranging from 4.0 to 8.0. The photoproduction of *OH in HA solution with algae with or without Fe(III) under a 250 W HPML was greater than that under a 125 W HPML. The photoproduction of *OH in irradiated samples was influenced by the pH. The results showed that HPML exposure for 4 h in the 4-8 pH range led to the highest *OH photoproduction at pH 4.0.

Recrystallization of freezable bound water in aqueous solutions of medium concentrations

Institute of Scientific and Technical Information of China (English)

赵立山; 潘礼庆; 纪爱玲; 曹则贤; 王强

2016-01-01

For aqueous solutions with freezable bound water, vitrification and recrystallization are mingled, which brings diffi-culty to application and misleads the interpretation of relevant experiments. Here, we report a quantification scheme for the freezable bound water based on the water-content dependence of glass transition temperature, by which also the concentra-tion range for the solutions that may undergo recrystallization finds a clear definition. Furthermore, we find that depending on the amount of the freezable bound water, different temperature protocols should be devised to achieve a complete recrys-tallization. Our results may be helpful for understanding the dynamics of supercooled aqueous solutions and for improving their manipulation in various industries.

Orientational order and dynamics of water in bulk and in aqueous solutions of uranyl ions

International Nuclear Information System (INIS)

Chopra, Manish; Choudhury, Niharendu

2014-01-01

Molecular dynamics simulations in canonical ensemble of aqueous solutions of uranyl nitrate and bulk water at ambient condition have been carried out to investigate orientational order and dynamics of water. The orientational distributions of water around a central water molecule in bulk water and around a uranyl ion in an aqueous uranyl solution have been calculated. Orientational dynamics of water in bulk and in aqueous uranyl nitrate solution have also been analysed. (author)

Removal of Murexide from Aqueous Solution Using Pomegranate bark as adsorbent

International Nuclear Information System (INIS)

Ishaq, M.I.; Shakirullah, M.; Ahmad, I.; Sultan, S.; Saeed, K.

2012-01-01

The adsorption of Murexide from aqueous solution onto the Pomegranate bark was investigated at room temperature. The morphological study presented that the HNO/sub 3/ treatment increased the surface roughness of the adsorbent. EDX studies show that the untreated Pomegranate bark had carbon content (52 wt %) and oxygen content (44 wt %) while in the case of HNO/sub 3/ treated pomegranate bark, the carbon quantity decreased (42 wt %) and oxygen quantity (52 wt %) increased. The results showed that the adsorption of Murexide dye from aqueous solution was increased as increased the adsorption time and then equilibrium was reached after 30 min of adsorption time. The HNO/sub 3/ treated Pomegranate bark adsorbed high quantity of Murexide (1.7 mg/g) as compared to untreated Pomegranate bark (0.73 mg/g), which might be due to increased surface roughness. The adsorption of Murexide was also studied at different pH, which presented that low pH was favorable for the removal of color material from aqueous solution. (author)

Photolysis of imidacloprid in aqueous solution

International Nuclear Information System (INIS)

Moza, P.N.; Hustert, K.; Feicht, E.; Kettrup, A.

1998-01-01

The photolysis of the insecticide imidacloprid in aqueous solution has been examined. Irradiation at 290 nm resulted in 90 % substrate transformation in 4 h. The degradation approximately followed first order kinetics; the rate constant is 1.6 × 10 −4 s −1 and half-life 1.2 h. 6-Chloronicotinaldehyde, N-methylnicotinacidamide, 1-(6-chloronicotinyl)imidazolidone and 6-chloro-3-pyridyl-methylethylendiamine were the main photoproducts identified by CG-MS analysis. (author)

Natural biosorbents (garlic stem and horse chesnut shell) for removal of chromium(VI) from aqueous solutions.

Science.gov (United States)

Parlayıcı, Şerife; Pehlivan, Erol

2015-12-01

The biosorption of Cr(VI) by the garlic stem (GS)-Allium sativum L. and horse chesnut shell (HCS)-Aesculus hippocastanum plant residues in a batch type reactor was studied in detail for the purpose of wastewater treatment. The influence of initial Cr(VI) concentration, time, and pH was investigated to optimize Cr(VI) removal from aqueous solutions and equilibrium isotherms and kinetic data. This influence was evaluated. The adsorption capacity of the GS and the HCS for Cr(VI) was determined with the Langmuir and Freundlich isotherm models, and the data was fitted to the Langmuir. The adsorption capacity of the GS and the HCS was found to be 103.09 and 142.85 mg/g of adsorbent from a solution containing 3000 ppm of Cr(VI), respectively. The GS's capacity was considerably lower than that of the HCS in its natural form. Gibbs free energy was spontaneous for all interactions, and the adsorption process exhibited exothermic enthalpy values. The HCS was shown to be a promising biosorbent for Cr(VI) removal from aqueous solutions.

Dissolution of carbon dioxide in aqueous electrolyte solutions, in the context of geological storage: A thermodynamic approach

International Nuclear Information System (INIS)

Liborio, Barbara

2017-01-01

This thesis studies the enthalpy of solution of carbon dioxide in electrolyte aqueous solutions. To develop theoretical models describing the systems (CO 2 -water-salt) under the geological storage conditions of carbon dioxide, it is necessary to have experimental data, namely solubility and enthalpy. In this study, a customized flow mixing unit was adapted to a SETARAM C-80 calorimeter to measure the enthalpy of CO 2 solution in aqueous electrolyte solutions (NaCl, CaCl 2 and Na 2 SO 4 ) at the ionic strengths between 2 and 6 and at temperatures between 323.1 K and 372.9 K and pressures ranging from 2 to 16 MPa. Data from the literature were used to adjust the thermodynamic phase equilibrium model in the Y-φ approach. The thermodynamic model reproduces the experimental enthalpies to plus or minus 10%. The calculation of the enthalpy in the rigorous model is strongly dependent on the data of the literature. An experimental device has been set up for the determination of the molar volume of CO 2 at infinite dilution, which is necessary for thermodynamic modeling. The carbon dioxide to be stored may contain impurities such as annexes (O 2 , N 2 , SO x , H 2 S, N y O x , H 2 , CO and Ar). Under the objective of studying the influence of these impurities, an experimental apparatus has been set up for the measurement of enthalpies of solution of SO 2 in water and aqueous solutions of NaCl and the first results are promising. (author)

The synthesis of nucleotide in the aqueous solution induced by low energy ions

International Nuclear Information System (INIS)

Shi Huaibin; Shao Chunlin; Wang Xiangqin; Yu Zengliang

2000-08-01

A new apparatus was designed to induce reactions in aqueous solution by introducing low energy ions into the aqueous solution, this apparatus overcome the defaults of the old ones which demanded vacuum and made it possible to study the action among solutions, it also expanded the ion implantation biology. The role of low energy ions was introduced into the study of the origin of life, primitive earth conditions were imitated to study prior-life synthesis of nucleotide by introducing low energy ions into aqueous solution, low energy N + was implanted into adenine supersaturation solution including D-ribose and NH 4 H 2 PO 4 , it was confirmed that 5'-AMP was gained by HPLC analysis of the products. In comparison with other methods in this field, this one is simpler and nearer to the primitive earth conditions, thus it provided a new try for the studying of the origin of life

A new polymeric adsorbent developing for uranium recovering and richment from aqueous media

International Nuclear Information System (INIS)

Gueler, H.; Aycik, G. A.; Sahiner, N.; Gueven, O.

1997-01-01

Using adsorbents is thought to be the most effective method for recovering the low concentrations of uranium in the aqueous media because of their fast and selective uptake of uranium, a sufficient adsorption capacity and high physical and chemical stability against the media. In this study, a new polymeric adsorbent bearing both hydrophilic groups providing swelling in water and amidoxime groups for chelating with uranyl ions (UO 2 ''2+) has been developed and its adsorptive ability for uranium from aqueous media has been investigated. The polymers obtained by irradiating the solution of polyethylene glycol (PEG) in acrylonitrile (AN) are defined as Interpenetrating Polymer Networks (IPNs) and the adsorbent has been obtained by applying the amidoximation reaction to the IPNs with a conversion of % 60 approximately. Kinetics of the conversion reaction of nitrile (CN) group to amidoxime (HONCNH 2 ) group has been studied by reacting with hydroxylamine (NH 2 OH) solution at a molar ratio of NH 2 OH/CN=1.25 in aqueous media at different temperatures, 30,40,50''0C, for 3-4 days. The degree of amidoximation was determined by UO 2 ''2+ ion adsorption and FTIR spectrometer and the UO 2 ''2+ ion adsorption values were found by both UV and gamma spectrometry and also by gravimetry. It was found that the polymeric adsorbent has a very high adsorption ability for uranium (∼ 540 mg U/g IPN/day)

Solubility of corrosion products of plain steel in oxygen-containing water solutions at high parameters

International Nuclear Information System (INIS)

Martynova, O.I.; Samojlov, Yu.F.; Petrova, T.I.; Kharitonova, N.L.

1983-01-01

Technique for calculation of solubility of iron corrosion products in oxygen-containing aqueous solutions in the 298-573 K temperature range is presented. Solubility of corrosion products of plain steel in deeply-desalinizated water in the presence of oxygen for the such range of the temperatures is experimentally determined. Rather good convergence between calculated and experimental data is noted

KINETICS OF THE HYDROXYPROPYLATION OF POTATO STARCH IN AQUEOUS-SOLUTION

NARCIS (Netherlands)

LAMMERS, G; STAMHUIS, EJ; BEENACKERS, AACM

Kinetic results are presented for the hydroxypropylation of Potato starch with methyloxirane in aqueous solution. Reaction temperatures were varied from 303 to 362 K. Sodium hydroxide was used as a catalyst. The overall conversion rate of methyloxirane in alkaline starch solution is determined by

A novel cyanide-selective colorimetric and fluorescent chemosensor: First molecular security keypad lock based on phosphotungstic acid and CN{sup −} inputs

Energy Technology Data Exchange (ETDEWEB)

Tavallali, Hossein, E-mail: Tavallali@pnu.ac.ir; Deilamy-Rad, Gohar; Parhami, Abolfath; Hasanli, Nahid

2014-02-15

Highlights: • Our probe is commercially available with good photo stability and high quantum yield. • Both color and fluorescence change with long emission wavelength in aqueous media. • Characteristics of an ON–OFF–ON fluorescence switch. • The simple receptor for CN{sup -} detection with low detection limit (≪WHO). • Mimic the function of a security keypad lock on sequential addition of PTA and CN{sup −}. -- Abstract: Rhodamine B (Rh{sub B}) an available dye has been developed as novel and efficient colorimetric and fluorometric chemosensor for cyanide ions in an absolutely aqueous media. The UV–vis absorption and fluorescent emission titrations experiments have been employed to study the sensing process. Rh{sub B} could act as an efficient “ON–OFF” fluorescent response for phosphotungstic acid (H{sub 3}PW{sub 12}O{sub 40} or PTA) based on an ion associate process. Also (Rh{sub B}{sup +}){sub 3}·PTA{sup 3−} could operate as an “OFF–ON” fluorescent sensor for cyanide anions based on a ligand substitution process. It has been identified as highly sensitive probe for CN{sup −} which responds at 0.3 and 0.04 μmol L{sup −1} concentration levels by absorption and fluorescent method respectively. Depending upon the sequence of addition of PTA and CN{sup −} ions into the solution, Rh{sub B} could be as a molecular security keypad lock with PTA and CN{sup −} inputs. The ionic inputs to new fluorophore have been mimicked as a superimposed electronic molecular keypad lock. The results were compared successfully (>96%) with the data of a spectrophotometry approved method (EPA 9014-1) for cyanide ions.

Extended UNIQUAC model for thermodynamic modeling of CO2 absorption in aqueous alkanolamine solutions

DEFF Research Database (Denmark)

Faramarzi, Leila; Kontogeorgis, Georgios; Thomsen, Kaj

2009-01-01

The extended UNIQUAC model [K. Thomsen, R Rasmussen, Chem. Eng. Sci. 54 (1999) 1787-1802] was applied to the thermodynamic representation of carbon dioxide absorption in aqueous monoethanolamine (MEA), methyldiethanolamine (MDEA) and varied strength mixtures of the two alkanolamines (MEA-MDEA). F......The extended UNIQUAC model [K. Thomsen, R Rasmussen, Chem. Eng. Sci. 54 (1999) 1787-1802] was applied to the thermodynamic representation of carbon dioxide absorption in aqueous monoethanolamine (MEA), methyldiethanolamine (MDEA) and varied strength mixtures of the two alkanolamines (MEA......) are included in the parameter estimation process. The previously unavailable standard state properties of the alkanolamine ions appearing in this work, i.e. MEA protonate, MEA carbamate and MDEA protonate are determined. The concentration of the species in both MEA and MDEA solutions containing CO2...

Treatment of cyanide-contained Waste Water

International Nuclear Information System (INIS)

Scheglov, M.Y.

1999-01-01

This work contains results of theoretical and experimental investigations of possibility to apply industrial ionites of different kinds for recovering complex cyanide of some d-elements (Cu, Zn, an dso on) and free CN-ions with purpose to develop technology and unit for plating plant waste water treatment. Finally, on basis of experimental data about equilibrium kinetic and dynamic characteristic of the sorption in model solutions, strong base anionite in CN- and OH-forms was chosen. This anionite has the best values of operational sorption uptake. Recommendations of using the anionite have been developed for real cyanide-contained wastewater treatment

Removal of radium from aqueous solutions using adsorbent produced from coconut coir pith

International Nuclear Information System (INIS)

Zalina Laili; Muhamat Omar; Mohd Zaidi Ibrahim; Esther Phillip; Mohd Abdul Wahab Yusof; Hassan, A.

2008-08-01

A study was conducted to evaluate the potential use of the coconut coir pith as an adsorbent for the removal of radium from aqueous solutions. Experiments to establish adsorptions as a function of pH and contact time were carried out. The results showed that radium adsorption are dependent upon pH and contact time of coconut coir pith with aqueous solutions. 70-80% of radium were adsorbed in the neutral to alkaline pH range. The amount of radium adsorbed also increased with contact time, reaching an optimum after 250 min. Thus, it can be concluded that the coconut coir pith has the potential to be used as an adsorbent in radium removal from aqueous solutions. (Author)

Removal of uranium and thorium from aqueous solution by ultrafiltration (UF) and PAMAM dendrimer assisted ultrafiltration (DAUF)

International Nuclear Information System (INIS)

Ilaiyaraja, P.; Ashish Kumar Singha Deb; Ponraju, D.

2015-01-01

Studies on removal of U(VI) and Th(IV) from aqueous solution have been carried out by ultrafiltration (UF) and dendrimer assisted ultrafiltration (DAUF) using regenerated cellulose acetate membrane and PAMAM [poly(amido)amine] dendrimer chelating agent. In UF, the U(VI) and Th(IV) are removed from aqueous solution by adsorption/mass deposition on the membrane at pH > 4. In DAUF, the water soluble PAMAM dendrimer chelating agent effectively concentrates these metal ions in retentate thereby preventing the mass deposition on membrane. At acidic pH (≤3), the binding of metal ions with PAMAM dendrimer is very weak and hence PAMAM can be regenerated and reused. Electronic supplementary material. The online version of this article (doi:10.1007/s10967-014-3462-x) contains supplementary material, which is available to authorized users. (author)

Densities concentrations of aqueous of uranyl nitrate solutions

International Nuclear Information System (INIS)

Rodrigo Otero, A.; Rodriguez Hernandez, B.; Fernandez Rodriguez, L.

1966-01-01

The ratio density-concentration of aqueous uranyl nitrate solutions expressed as U 3 O 8 grams/liter, U grams/liter and hexahydrate uranyl nitrate weight percent at different temperatures, are established. Experimental values are graphically correlated and compared whit some published data. (Author) 2 refs

Volumetric and viscometric studies of some drugs in aqueous solutions at different temperatures

International Nuclear Information System (INIS)

Dhondge, Sudhakar S.; Zodape, Sangesh P.; Parwate, Dilip V.

2012-01-01

Highlights: ► Study of aqueous solutions of biologically important compounds has been reported. ► MH is used for treating type II diabetes, RH is in treatment of peptic ulcer and TH is used to treat severe pain. ► All the compounds act as structure makers by volumetric studies. ► MH and RH act as weak structure breakers and TH acts as a weak structure maker by viscometric studies. - Abstract: Density and viscosity measurements are reported for aqueous solutions of the drugs like Metformin hydrochloride (MH), Ranitidine hydrochloride (RH) and Tramadol hydrochloride (TH) at different temperatures T = (288.15, 298.15, and 308.15) K within the concentration range (0 to 0.15) mol · kg −1 . The density and viscosity data are used to obtain apparent molar volume of solute (φ V ) and relative viscosity (η r ) of aqueous solutions at different temperatures. The limiting apparent molar volume of solute (φ V 0 ), limiting apparent molar expansivity (φ E 0 ), thermal expansion coefficient (α ∗ ), hydration number (n h ), Jones–Dole equation viscosity A and B coefficients, experimental slope (S V ) at different temperatures, and temperature coefficient of Bi.e.(dB/dT) at T = 298.15 K were also obtained. The results obtained have been interpreted in terms of solute–solvent and solute–solute interactions and structure making/breaking ability of solute in the aqueous solution.

Adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution

International Nuclear Information System (INIS)

Tatsuya Suzuki

2013-01-01

The adsorption behaviors of trivalent actinides and lanthanides on pyridine resin in lithium chloride aqueous solution were investigated. The adsorbed amounts of lanthanides and the degree of mutual separation of lanthanides increased with an increase in the concentration of lithium chloride in aqueous solution. The group separation of the trivalent actinides and lanthanides was observed. This separation phenomenon is similar in a hydrochloric acid solution. However, the adsorption behavior of lanthanides in lithium chloride is different from their behavior in a hydrochloric acid solution. This fact shows that the adsorption mechanisms of lanthanides in a lithium chloride aqueous solution and in a hydrochloric acid solution are different; the adsorption mechanisms are attributed to the ion exchange in a hydrochloric acid solution, and to the complex formation with pyridine group in a lithium chloride solution. (author)

Dermal absorption of a dilute aqueous solution of malathion

Directory of Open Access Journals (Sweden)

Scharf John

2008-01-01

Full Text Available Malathion is an organophosphate pesticide commonly used on field crops, fruit trees, livestock, agriculture, and for mosquito and medfly control. Aerial applications can result in solubilized malathion in swimming pools and other recreational waters that may come into contact with human skin. To evaluate the human skin absorption of malathion for the assessment of risk associated with human exposures to aqueous solutions, human volunteers were selected and exposed to aqueous solutions of malathion. Participants submerged their arms and hands in twenty liters of dilute malathion solution in either a stagnant or stirred state. The "disappearance method" was applied by measuring malathion concentrations in the water before and after human exposure for various periods of time. No measurable skin absorption was detected in 42% of the participants; the remaining 58% of participants measured minimal absorbed doses of malathion. Analyzing these results through the Hazard Index model for recreational swimmer and bather exposure levels typically measured in contaminated swimming pools and surface waters after bait application indicated that these exposures are an order of magnitude less than a minimal dose known to result in a measurable change in acetylcholinesterase activity. It is concluded that exposure to aqueous malathion in recreational waters following aerial bait applications is not appreciably absorbed, does not result in an effective dose, and therefore is not a public health hazard.

Removal of Phenol in Aqueous Solution Using Kaolin Mineral Clay

International Nuclear Information System (INIS)

Sayed, M.S.

2008-01-01

Kaolin clay were tested for phenol removal as toxic liquid waste from aqueous waste water. Several experimental conditions such as weight and particle size of clay were investigated to study batch kinetic techniques, also the ph and concentration of the phenol solution were carried out. The stability of the Langmuir adsorption model of the equilibrium data were studied for phenol sorbent clay system. Infrared spectra, thermogravimetric and differential thermal analysis techniques were used to characterize the behavior of kaolin clay and kaolin clay saturated with phenol. The results obtained showed that kaolin clay could be used successfully as an efficient sorbent material to remove phenol from aqueous solution

Chemical dosimetry at less than 1000 rad: aqueous trimesic acid solutions

International Nuclear Information System (INIS)

Matthews, R.W.; Wilson, J.G.

1981-01-01

Aqueous solutions of trimesic acid were investigated for possible use as a chemical dosimeter. In aerated 10 -2 M sulphuric acid solution containing 10 -3 M trimesic acid, a highly fluorescent product is formed with its maximum fluorescence at 450nm when excited by 350nm light. The product has fluorescence characteristics very similar to quinine in 0.05 M sulphuric acid. The fluorescence intensity is linear with dose in the range 1-1000 rad and a precision of +-2% was obtained from a number of runs. Solutions are stable for at least several days before and after irradiation. The yield is little affected by moderate changes in trimesic acid concentration, oxygen concentration, water purity, energy of radiation and irradiation temperature. The small dependence of the yield on dose rate and the effect of measurement temperature on the fluorescence signal have been quantified. The most significant factor affecting the fluorescence signal is the hydrogen ion concentration of the solution. In aerated neutral and alkaline (pH 10) solutions, hydroxytrimesic acid (HTMA) is formed with G(HTMA) equal to 2.07 +- 0.04 and 2.21 +- 0.04, for 10 -3 M trimesate. In these solutions, G(HTMA) increases appreciably with increase in the trimesate concentration. The main fluorescent product formed in irradiated acid solutions was not identified but it was not HTMA. (author)

Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Alves, Kleber G. B. [Universidade Federal de Pernambuco, Departamento de Engenharia Mecanica (Brazil); Melo, Etelino F. de [Universidade Federal de Pernambuco, Departamento de Quimica Fundamental (Brazil); Andrade, Cesar A. S. [Universidade Federal de Pernambuco, Departamento de Bioquimica (Brazil); Melo, Celso P. de, E-mail: celso@df.ufpe.br [Universidade Federal de Pernambuco, Departamento de Fisica (Brazil)

2013-01-15

We report the synthesis of stable polyaniline nanoparticles (PANI{sub N}Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types-cationic (dodecyltrimethylammonium bromide-DTAB), anionic (sodium dodecyl sulfate-SDS), and non-ionic (Triton X-405-TX-405)-were used. The resulting PANI{sub N}Ps{sub s}urfactant samples were characterized through UV-Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI{sub N}Ps{sub s}urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs{sub s}urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 Multiplication-Sign 10{sup -3} to 6.9 Multiplication-Sign 10{sup -3}) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

International Nuclear Information System (INIS)

Alves, Kleber G. B.; Melo, Etelino F. de; Andrade, César A. S.; Melo, Celso P. de

2013-01-01

We report the synthesis of stable polyaniline nanoparticles (PANI N Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types—cationic (dodecyltrimethylammonium bromide—DTAB), anionic (sodium dodecyl sulfate—SDS), and non-ionic (Triton X-405–TX-405)—were used. The resulting PANI N Ps s urfactant samples were characterized through UV–Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI N Ps s urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs s urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 × 10 −3 to 6.9 × 10 −3 ) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

Sorption of ochratoxin A from aqueous solutions using β-cyclodextrin-polyurethane polymer.

Science.gov (United States)

Appell, Michael; Jackson, Michael A

2012-02-01

The ability of a cyclodextrin-polyurethane polymer to remove ochratoxin A from aqueous solutions was examined by batch rebinding assays. The results from the aqueous binding studies were fit to two parameter models to gain insight into the interaction of ochratoxin A with the nanosponge material. The ochratoxin A sorption data fit well to the heterogeneous Freundlich isotherm model. The polymer was less effective at binding ochratoxin A in high pH buffer (9.5) under conditions where ochratoxin A exists predominantly in the dianionic state. Batch rebinding assays in red wine indicate the polymer is able to remove significant levels of ochratoxin A from spiked solutions between 1-10 μg·L(-1). These results suggest cyclodextrin nanosponge materials are suitable to reduce levels of ochratoxin A from spiked aqueous solutions and red wine samples.

Removal of Hexavalent Chromium from Aqueous Solutions using ...

African Journals Online (AJOL)

The hexavalent chromium exists in aquatic media as water soluble complex anions and persist. These are concentrated in industrial waste water especially from the tannery industries and release of effluents from industries adversely affects the environment. The removal of heavy metals from aqueous solutions is carried ...

EPR study of the production of OH radicals in aqueous solutions of uranium irradiated by ultraviolet light

Directory of Open Access Journals (Sweden)

MARKO DAKOVIĆ

2009-06-01

Full Text Available The aim of the study was to establish whether hydroxyl radicals (•OH were produced in UV-irradiated aqueous solutions of uranyl salts. The production of •OH was studied in uranyl acetate and nitrate solutions by an EPR spin trap method over a wide pH range, with variation of the uranium concentrations. The production of •OH in uranyl solutions irradiated with UV was unequivocally demonstrated for the first time using the EPR spin-trapping method. The production of •OH can be connected to speciation of uranium species in aqueous solutions, showing a complex dependence on the solution pH. When compared with the results of radiative de-excitation of excited uranyl (*UO22+ by the quenching of its fluorescence, the present results indicate that the generation of hydroxyl radicals plays a major role in the fluorescence decay of *UO22+. The role of the presence of carbonates and counter ions pertinent to environmental conditions in biological systems on the production of hydroxyl radicals was also assessed in an attempt to reveal the mechanism of *UO22+ de-excitation. Various mechanisms, including •OH production, are inferred but the main point is that the generation of •OH in uranium containing solutions must be considered when assessing uranium toxicity.

Stability of Medium-Bridged Twisted Amides in Aqueous Solutions

Science.gov (United States)

Szostak, Michal; Yao, Lei; Aubé, Jeffrey

2012-01-01

“Twisted” amides containing non-standard dihedral angles are typically hypersensitive to hydrolysis, a feature that has stringently limited their utility in water. We have synthesized a series of bridged lactams that contain a twisted amide linkage but which exhibit enhanced stability in aqueous environments. Many of these compounds were extracted unchanged from aqueous mixtures ranging from the strongly basic to the strongly acidic. NMR experiments showed that tricyclic lactams undergo reversible hydrolysis at extreme pH ranges, but that a number of compounds in this structure class are indefinitely stable under physiologically relevant pH conditions; one bicyclic example was additionally water-soluble. We examined the effect of structure on the reversibility of amide bond hydrolysis, which we attributed to the transannular nature of the amino acid analogs. These data suggest that medium-bridged lactams of these types should provide useful platforms for studying the behavior of twisted amides in aqueous systems. PMID:19178141

Aqueous solution of basic fuchsin as food irradiation dosimeter

International Nuclear Information System (INIS)

Khan, H.M.; Naz, S.

2006-01-01

Dosimetric characterization of aqueous solution of basic fuchsin has been studied spectrophotometrically for the possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and decrease in the absorption with the radiation dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λ max (540nm) as well as 510, 460 and 400 nm wavelengths. At all these wavelengths, the decrease in the absorbance of the dosimeter was linear with respect to the absorbed dose from 0.05 to 0.6 kGy. The stability of dosimetric solution during the post-irradiation storage in the dark at room temperature showed that after initial bleaching during first eight days, the response was almost stable for about 34 days. The effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that the basic fuchsin dye is photosensitive as well as thermally sensitive. The possibility of using aqueous solution of basic fuchsin as food irradiation dosimeter will be discussed. (authors)

Adsorption of Cu 2+ , As 3+ and Cd 2+ ions from aqueous solution ...

African Journals Online (AJOL)

The adsorption of Cu2+, Cd2+ and As3+ ions on eggshell from aqueous solution was studied under batch conditions at 30, 40, 50 and 60oC and concentrations of 10, 20, 30, 60 and 80 mg/l. The partition coefficient for the ions between aqueous solution and chicken eggshell increased with time and with increase in the ...

Biamperometric analysis of nonaqueous scandium solutions containing lanthanides, lead and thorium

International Nuclear Information System (INIS)

Gevorgyan, A.M.; Talipov, Sh.T.; Kostylev, V.S.; Khadeev, V.A.; Nadol'skij, M.Ya.

1978-01-01

Investigated was a possibility of direct scandium titration in the presence of large rare earth quantities, and also a possibility of complexonometric scandium and rare earth sum determination at their joint presence in non-aqueous acetic acid solution. The titration was carried out at electrode voltage of 0.95V, background electrolyte concentration of lithium perchlorate being 0.2M. Non-aqueous magnesium complexonate was used as titrating reagent. Th and Pb complexonates are shown to be less stable as compared to Sc complexonate, and consequently, Th and Pb ions must not interfere with biamperometric titration of Sc ion. A method applied to analysis of binary mixture, containing scandium, and a method for model alloy and thortveitite mineral was developed. Well reproducible and precise enough results are obtained in all the cases. Ions of Bi, Cu, Cd, Zn, In, Ga and Ti interfere with determination

Removal of boron from aqueous solution using cryptocrystalline magnesite

CSIR Research Space (South Africa)

Masindi, Vhahangwele

2016-05-01

Full Text Available of Water Reuse and Desalination Removal of boron from aqueous solution using cryptocrystalline magnesite Vhahangwele Masindi and Mugera W. Gitari Abstract The present study aimed to evaluate the efficiency of using cryptocrystalline magnesite...

Structure of water and the thermodynamics of aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Nemethy, G.

1970-10-26

This report represents the summary of a series of lectures held at the Istituto Superiore di Sanita, Laboratori di Fisica, from 18 September to 26 October 1970. The topics discussed were: Intermolecular forces, the individual water molecule and the hydrogen bond, the structures of the solid phases of water, experimental information on the strucuture of liquid water, theoretical models of water structure, experimental properties and theoretical models of aqueous solutions of nonpolar solutes, polar solutes, and electrolytes, the conformational stability of biological macromolecules.

Radiation induced graft copolymerization of cellulosic fabric waste and its application in the removal of cyanide and dichromate from aqueous solution

International Nuclear Information System (INIS)

El-Kelesh, N.A.; Hashem, A.; Sokker, H.H.; Abd Elaal, S.E.

2005-01-01

Graft polymerization and crosslinking in radiation processing are attractive techniques for modification of the chemical and physical properties of the conventional polymers. The graft polymerization and subsequent chemical treatment can introduce a chelate agent function into a conventional polymer such as cellulosic fabric. Cellulosic graft copolymers were prepared by the reaction of the fiber with acrylonitrile (AN) and 2-acrylamido-2-methyl propane sulfonic acid (AMPS) in DMF initiated by gamma-radiation 60 Co. The grafted fabric was chemically treated with hydroxyl amine to obtain amidoxime form. Factors affecting on the grafting such as radiation dose, monomer concentration and solvent concentration as well as monomer composition was investigated. The chemically modified graft fabric was applied for recovery of cyanide and dichromate from aqueous solution. The CN show removal percent 89%, whereas dichromate has 65% removal percent

Theoretical approach to the destruction or sterilization of drugs in aqueous solution

International Nuclear Information System (INIS)

Slegers, Catherine; Tilquin, Bernard

2005-01-01

Two novel applications in the radiation processing of aqueous solutions of drugs are the sterilization of injectable drugs and the decontamination of hospital wastewaters by ionizing radiation. The parameters influencing the destruction of the drug in aqueous solutions are studied with a computer simulation program. This theoretical approach has revealed that the dose rate is the most important parameter that can be easily varied in order to optimize the destruction or the protection of the drug

Aqueous solution dispersement of carbon nanotubes

Science.gov (United States)

Kim, Jae-Woo (Inventor); Park, Cheol (Inventor); Choi, Sang H. (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

2011-01-01

Carbon nanotubes (CNTs) are dispersed in an aqueous buffer solution consisting of at least 50 weight percent water and a remainder weight percent that includes a buffer material. The buffer material has a molecular structure defined by a first end, a second end, and a middle disposed between the first and second ends. The first end is a cyclic ring with nitrogen and oxygen heteroatomes, the middle is a hydrophobic alkyl chain, and the second end is a charged group.

Simultaneous removal of iron and manganese of aqueous solutions using as adsorbent a Mexican natural zeolite

International Nuclear Information System (INIS)

Garcia M, A.; Solache R, M. J.; Olguin G, M. T.

2009-01-01

In this work was evaluated the removal capacity of iron and manganese of aqueous solutions using a Mexican natural zeolite. It was observed that the Freundlich pattern describes the adsorption process appropriately and that a competitive effect exists between both metals by the exchange places of the zeolite, when it is starting of solutions that contain to both metals, impacting mainly in the manganese removal. A natural zeolite coming from the Puebla State, Mexico was used. The material was milled and sieved to a mesh size 30 and was conditioned with a solution 0.5 N of sodium chloride. Later on was characterized by means of scanning electron microscopy and X-ray diffraction.

Experimental measurements of U60 nanocluster stability in aqueous solution

Science.gov (United States)

Flynn, Shannon L.; Szymanowski, Jennifer E. S.; Gao, Yunyi; Liu, Tianbo; Burns, Peter C.; Fein, Jeremy B.

2015-05-01

In this study, the aqueous behavior of isolated U60 nanoclusters (K16Li25[UO2(O2)OH]60)-19 was studied under several pH conditions and nanocluster concentrations to determine if the nanoclusters exhibit solid phase buffering behavior or if they exhibit behavior more like aqueous complexes. U60 is a cage cluster consisting of 60 (UO2)(O2)2(OH)2 uranyl polyhedral which share OH and O2 groups with their neighboring uranyl polyhedral, resulting in negatively charged cage clusters whose charge is at least partially offset by K+ and Li+ in the aqueous phase. Batch experiments to monitor nanocluster stability were conducted for 16 days at pH 7.5, 8.0 and 8.5 at nanocluster suspension concentrations of 1.4, 2.8 and 6.0 g/L. The aqueous concentrations of U, Li, and K, determined after 10 kDa molecular weight filtration, achieved steady-state with the nanoclusters within 24 h. The steady-state aqueous U, Li, and K concentrations were independent of solution pH, however they increased with increasing nanocluster concentration, indicating that the nanoclusters do not buffer the aqueous activities as a bulk solid phase would, but exhibit behavior that is more characteristic of dissolved aqueous complexes. The ion activity product (I.A.P.) value was calculated using two approaches: (1) treating the nanoclusters as a solid phase with an activity of one, and (2) treating the nanoclusters as aqueous complexes with a non-unit activity equal to their concentration in solution. The I.A.P. values that were calculated with non-unit activity for the nanoclusters exhibited significantly less variation as a function of nanocluster concentration compared to the I.A.P. values calculated with a nanocluster activity of one. The results yield a calculated log dissociation constant for the U60 nanoclusters of 9.2 + 0.2/-0.3 (1σ). Our findings provide a better understanding of the thermodynamic stability and behavior of U60 nanoclusters in aqueous systems, and can be used to estimate the

The effect of gamma irradiation on rice protein aqueous solution

Science.gov (United States)

Baccaro, Stefania; Bal, Oya; Cemmi, Alessia; Di Sarcina, Ilaria

2018-05-01

The use of proteins as natural biopolymers are sensibly increasing in several application fields such as food industry, packaging and environment protection. In particular, rice proteins (RP) present good nutritional, hypoallergenic and healthful properties very interesting for human consumption. Since ionizing radiation can be successfully applied on protein containing systems involved in different industrial processes, this work aims to determine the effect of gamma radiation on 5 wt%-7.5 wt% RP aqueous solutions in a wide range of absorbed doses up to around 40 kGy. The changes of RP secondary and tertiary structures and their chemical composition were followed by UV-VIS absorbance spectroscopy, luminescence analysis and pH measurements. The experimental data showed the occurrence of the unfolding of RP chains with the increase of the absorbed dose and the formation of new molecules, due to the reaction among tryptophane and tyrosine amino acids and the radical species induced by gamma radiation. The results are also confirmed by the modification of the pH values measured for the irradiated solutions.

Actinide removal from aqueous solution with activated magnetite

International Nuclear Information System (INIS)

Kochen, R.L.; Thomas, R.L.

1987-01-01

An actinide aqueous waste treatment process using activated magnetite has been developed at Rocky Flats. The use and effectiveness of various magnetites in lowering actinide concentrations in aqueous solution are described. Experiments indicate that magnetite particle size and pretreatment (activation of the magnetite surface with hydroxyl ions greatly influence the effective use of magnetite as an actinide adsorbent. With respect to actinide removal, Ba(OH) 2 -activated magnetite was more effective over a broader pH range than was NaOH-activated magnetite. About 50% less Ba(OH) 2 -activated magnetite was required to lower plutonium concentration from 10 -4 to 10 -8 g/l. 7 refs., 8 tabs

Degradation of Para-Phenylenediamine in Aqueous Solution by ...

African Journals Online (AJOL)

In this research Photo-Fenton Oxidation of Para-Phenylenediamine (PPD) in aqueous solution by UV/Fenton's reagent (Fe2+ and H2O2) was investigated. ... lower concentration of Phenylenediamines and UV-C assisted photo-Fenton showed that the photo-Fenton process was very effective than the normal Fenton process ...

Radiolysis of Aqueous Benzene Solutions

Energy Technology Data Exchange (ETDEWEB)

Christensen, H

1964-05-15

Aerated and deaerated aqueous solutions of benzene have been irradiated with {sup 60}Co {gamma}-rays. The products of radiolysis in deaerated, unbuffered or acid, solutions were phenol, biphenyl, hydrogen and in acid solutions also hydrogen peroxide with the following yields: G(phenol) = 0. 37 (0. 37), G(biphenyl) = 1.3 (1.7), G(H{sub 2}) = 0.44 (0. 43) and G(H{sub 2}O{sub 2}) = 0 (0.60), the figures in brackets giving the results for acid solutions. The results are shown to agree with the conclusion that k(e{sup -}{sub aq} + H{sub 2}O{sub 2}) >> k(H + H{sub 2}O{sub 2}). Furthermore, the results indicate that a competition takes place between the reactions: 2 C{sub 6}H{sub 6}OH {center_dot} -> dimer -> biphenyl. C{sub 6}H{sub 7} {center_dot} + C{sub 6}H{sub 6}OH {center_dot} -> dimer -> biphenyl. The yields in aerated, unbuffered or acid, solutions were: G(phenol) = 2.1 (2.3), G(biphenyl) = 0 (0), and G(H{sub 2}O{sub 2}) = 2.2 (3.1), the figures in brackets being valid for acid solutions. The ratio k(H + C{sub 6}H{sub 6})/k(H + O{sub 2}) was 1.4x10{sup -2}. The results indicate that peroxides, or more probably hydroperoxides, take part in the reactions. After the addition of Fe{sup 2+} or Fe{sup 3+} to aerated acid solutions G(phenol) was increased to 6.6 and 3.4 respectively. Oxygen was consumed more rapidly in the presence of Fe. Reaction mechanisms are discussed.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds

Energy Technology Data Exchange (ETDEWEB)

Ramos-Ramirez, Esthela, E-mail: ramosre@quijote.ugto.mx [Centro de Investigaciones en Quimica Inorganica de la Universidad de Guanajuato, Noria Alta s/n, Col. Noria Alta, C.P. 36050, Guanajuato, Gto. (Mexico); Gutierrez Ortega, Norma L.; Conteras Soto, Cesar A. [Centro de Investigaciones en Quimica Inorganica de la Universidad de Guanajuato, Noria Alta s/n, Col. Noria Alta, C.P. 36050, Guanajuato, Gto. (Mexico); Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, km 36.5, La Marquesa, Coyoacan Mexico, C.P. 52750 (Mexico); Olguin Gutierrez, Maria T. [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca s/n, km 36.5, La Marquesa, Coyoacan Mexico, C.P. 52750 (Mexico)

2009-12-30

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio = 2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N{sub 2} adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds

International Nuclear Information System (INIS)

Ramos-Ramirez, Esthela; Gutierrez Ortega, Norma L.; Conteras Soto, Cesar A.; Olguin Gutierrez, Maria T.

2009-01-01

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio = 2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N 2 adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Adsorption isotherm studies of chromium (VI) from aqueous solutions using sol-gel hydrotalcite-like compounds.

Science.gov (United States)

Ramos-Ramírez, Esthela; Ortega, Norma L Gutiérrez; Soto, Cesar A Contreras; Gutiérrez, Maria T Olguín

2009-12-30

In under-developed countries, industries such as paint and pigment manufacturing, leather tanning, chrome plating and textile processing, usually discharge effluents containing Cr(VI) and Cr(III) into municipal sanitary sewers. It has been reported that Cr(VI) acts as a powerful epithelial irritant and as a human carcinogen. In the present work, hydrotalcite-like compounds with a Mg/Al ratio=2 were synthesized by the sol-gel method. The hydrotalcite-like compounds and their corresponding thermally treated products were characterized by powder X-ray diffraction, infrared spectroscopy and N(2) adsorption. The hydrotalcite-like compounds and the heated solids were used as adsorbents for Cr(VI) in aqueous solutions. Adsorption isotherm studies of Cr(VI) from aqueous solution are described. The adsorbent capacity was determined using the Langmuir, Freundlich and Dubinin-Radushkevich adsorption isotherm models. The Cr(VI) adsorption isotherm data fit best to the Langmuir isotherm model. The maximum Cr(VI) uptake by hydrotalcite and the heated solids was determined using the Langmuir equation and was found to range between 26 and 29 mg Cr(VI)/g adsorbent.

Corrosion control of vanadium in aqueous solutions by amino acids

International Nuclear Information System (INIS)

El-Rabiee, M.M.; Helal, N.H.; El-Hafez, Gh.M. Abd; Badawy, W.A.

2008-01-01

The electrochemical behavior of vanadium in amino acid free and amino acid containing aqueous solutions of different pH was studied using open-circuit potential measurements, polarization techniques and electrochemical impedance spectroscopy (EIS). The corrosion current density, i corr , the corrosion potential, E corr and the corrosion resistance, R corr , were calculated. A group of amino acids, namely, glycine, alanine, valine, histidine, glutamic and cysteine has been investigated as environmentally safe inhibitors. The effect of Cl - on the corrosion inhibition efficiency especially in acid solutions was investigated. In neutral and basic solutions, the presence of amino acids increases the corrosion resistance of the metal. The electrochemical behavior of V before and after the corrosion inhibition process has shown that some amino acids like glutamic acid and histidine have promising corrosion inhibition efficiency at low concentration (≅25 mM). The inhibition efficiency (η) was found to depend on the structure of the amino acid and the constituents of the corrosive medium. The corrosion inhibition process is based on the adsorption of the amino acid molecules on the metal surface and the adsorption process follows the Freundlich isotherm. The adsorption free energy for valine on V in acidic solutions was found to be -9.4 kJ/mol which reveals strong physical adsorption of the amino acid molecules on the vanadium surface

Study of the radiolysis of tetracycline hidrochloride in aerated aqueous solutions

International Nuclear Information System (INIS)

Guedes, S.M.L.; Vasconcellos, M.B.A.

1983-01-01

The radiolysis of tetracycline hydrochloride (TC) was studied in neutral, acid and alkaline aerated solutions, by electron spin resonance spectroscopy at 77K. The paramagnetic species observed are: H.; OH.; HO 2 .; e - trapped and impurity radical. The reaction mechanism shows that the solute reacts with the solvent before the radiolysis and produces H + ions, as a consequence of the ionization of tricarbonylmethane group. The H + ions react with the e - from the radiolysis of water and produce HO 2 in the presence of O 2 . The interaction of TC with the alkaline solvent favours the interaction between gamma rays and solute. The products formed in the interaction of solute with the solvent before the radiolysis, as a consenquence of the ionization of TC, according to the pH of the solution, are of fundamental importance in the interaction of gamma rays with the solute. A crude estimate of the average distance that the e - is able to travel through solvent molecules before its capture by the solute was obtained in these 0.1N, 0.5N and 1.0N NaOH aqueous solutions. Until [TC] - travels more in solutions that contain less [NaOH]. In higher [TC] the e - travels through 680 solvent molecules. In order to explain the selective capture of the e3- by solute molecules, a simple model is suggested based on the existence of channel walls of solvent molecules where the electrical atraction betwwed Na + and e - influences the collision frequency and the energy loss. (Author) [pt

Ultrafast dynamics of hydrogen bond exchange in aqueous ionic solutions.

Science.gov (United States)

Park, Sungnam; Odelius, Michael; Gaffney, Kelly J

2009-06-04

The structural and dynamical properties of aqueous ionic solutions influence a wide range of natural and biological processes. In these solutions, water has the opportunity to form hydrogen bonds with other water molecules and anions. Knowing the time scale with which these configurations interconvert represents a key factor to understanding the influence of molecular scale heterogeneity on chemical events in aqueous ionic solutions. We have used ultrafast IR spectroscopy and Car-Parrinello molecular dynamics (CPMD) simulations to investigate the hydrogen bond (H-bond) structural dynamics in aqueous 6 M sodium perchlorate (NaClO4) solution. We have measured the H-bond exchange dynamics between spectrally distinct water-water and water-anion H-bond configurations with 2DIR spectroscopy and the orientational relaxation dynamics of water molecules in different H-bond configurations with polarization-selective IR pump-probe experiments. The experimental H-bond exchange time correlates strongly with the experimental orientational relaxation time of water molecules. This agrees with prior observations in water and aqueous halide solutions, and has been interpreted within the context of an orientational jump model for the H-bond exchange. The CPMD simulations performed on aqueous 6 M NaClO4 solution clearly demonstrate that water molecules organize into two radially and angularly distinct structural subshells within the first solvation shell of the perchlorate anion, with one subshell possessing the majority of the water molecules that donate H-bonds to perchlorate anions and the other subshell possessing predominantly water molecules that donate two H-bonds to other water molecules. Due to the high ionic concentration used in the simulations, essentially all water molecules reside in the first ionic solvation shells. The CPMD simulations also demonstrate that the molecular exchange between these two structurally distinct subshells proceeds more slowly than the H

Stabilizers of edaravone aqueous solution and their action mechanisms. 1. Sodium bisulfite

OpenAIRE

Tanaka, Masahiko; Sugimura, Natsuhiko; Fujisawa, Akio; Yamamoto, Yorihiro

2017-01-01

Edaravone (3-methyl-1-phenyl-2-pyrazolin-5-one) has been used as a free radical scavenging drug for the treatment of acute ischemic stroke in Japan since 2001. Edaravone is given to patients intravenously; therefore, it is distributed in the form of an aqueous solution. However, aqueous solutions of edaravone are very unstable because it is present as edaravone anion, which is capable of transferring an electron to free radicals including oxygen, and becomes edaravone radical. We observed the...

Degradation of alachlor in aqueous solution by using hydrodynamic cavitation.

Science.gov (United States)

Wang, Xikui; Zhang, Yong

2009-01-15

The degradation of alachlor aqueous solution by using hydrodynamic cavitation was systematically investigated. It was found that alachlor in aqueous solution can be deomposed with swirling jet-induced cavitation. The degradation can be described by a pseudo-first-order kinetics and the degradation rate was found to be 4.90x10(-2)min(-1). The effects of operating parameters such as fluid pressure, solution temperature, initial concentration of alachlor and medium pH on the degradation rates of alachlor were also discussed. The results showed that the degradation rates of alachlor increased with increasing pressure and decreased with increasing initial concentration. An optimum temperature of 40 degrees C existed for the degradation rate of alachlor and the degradation rate was also found to be slightly depend on medium pH. Many degradation products formed during the process, and some of them were qualitatively identified by GC-MS.

Lanthanide complexation in aqueous solutions

International Nuclear Information System (INIS)

Choppin, G.R.

1984-01-01

The lanthanide elements form an extended series of cations with the same charge, slightly varying radii and useful magnetic and spectroscopic properties. Their use in technology is growing rapidly as their properties are more fully explored. The lanthanides also offer scientists valuable and often unique probes for investigating a variety of chemical and physical phenomena. This review has attempted to call attention to these latter uses without trying to provide a thorough discussion of all the relevant literature. Hopefully, awareness of the more interesting facets of present studies of lanthanide complexes in aqueous solution will spur even more advances in the use of these elements. (Auth.)

Ionizing radiation induced degradation of salicylic acid in aqueous solution

Science.gov (United States)

Albarrán, Guadalupe; Mendoza, Edith

2018-06-01

The radiation-induced degradation of salicylic acid (SA-) in aqueous solutions (1.0 and 0.1 mmol dm-3) saturated with N2O or air or without oxygen were studied. Irradiation was carried out using a cobalt-60 source. With a 1 mmol dm-3 solution saturated with N2O a seemingly total degradation occurred at about 18 kGy, although small quantities of 2,3-dihydroxybenzoic acid, catechol and 2,5-dihydroxybenzoic acid were present at that dose at concentrations of 67, 22 and 6 μmol dm-3 respectively. Under air and when free oxygen, the three radiolytic products were present at 18.54 kGy while SA- was destroyed only to 90% and 62%, respectively. In the case of 0.1 mmol dm-3 SA- solutions, the acid was degraded at 3.5 kGy if the solution contained N2O, at 5.8 kGy in air and at 7 kGy without oxygen. The concentration of the radiolytic products increased with increasing dose and after a maximum they decreased. The oxidation was followed by measuring the chemical oxygen demand; the slopes were 0.48 and 0.11, 0.21 and 0.07, 0.15 and 0.03 mmol dm-3 kGy-1 for 1.0 and 0.10 mmol dm-3 solutions saturated with N2O or air or without oxygen, respectively.

Calculation of chemical equilibrium between aqueous solution and minerals: the EQ3/6 software package

International Nuclear Information System (INIS)

Wolery, T.J.

1979-01-01

The newly developed EQ/36 software package computes equilibrium models of aqueous geochemical systems. The package contains two principal programs: EQ3 performs distribution-of-species calculations for natural water compositions; EQ6 uses the results of EQ3 to predict the consequences of heating and cooling aqueous solutions and of irreversible reaction in rock--water systems. The programs are valuable for studying such phenomena as the formation of ore bodies, scaling and plugging in geothermal development, and the long-term disposal of nuclear waste. EQ3 and EQ6 are compared with such well-known geochemical codes as SOLMNEQ, WATEQ, REDEQL, MINEQL, and PATHI. The data base allows calculations in the temperature interval 0 to 350 0 C, at either 1 atm-steam saturation pressures or a constant 500 bars. The activity coefficient approximations for aqueous solutes limit modeling to solutions of ionic strength less than about one molal. The mathematical derivations and numerical techniques used in EQ6 are presented in detail. The program uses the Newton--Raphson method to solve the governing equations of chemical equilibrium for a system of specified elemental composition at fixed temperature and pressure. Convergence is aided by optimizing starting estimates and by under-relaxation techniques. The minerals present in the stable phase assemblage are found by several empirical methods. Reaction path models may be generated by using this approach in conjunction with finite differences. This method is analogous to applying high-order predictor--corrector methods to integrate a corresponding set of ordinary differential equations, but avoids propagation of error (drift). 8 figures, 9 tables

Solubility and viscosity for CO_2 capture process using MEA promoted DEAE aqueous solution

International Nuclear Information System (INIS)

Fu, Dong; Wang, LeMeng; Zhang, Pan; Mi, ChenLu

2016-01-01

Highlights: • Solubility of CO_2 in MEA promoted DEAE aqueous solution was measured. • Mass fraction and temperature dependences of solubility were illustrated. • Viscosities of carbonated MEA–DEAE solutions were measured and calculated. • Temperature, mass fraction and CO_2 loading dependences of viscosity were illustrated. - Abstract: The saturated solubility of CO_2 in monoethanolamine (MEA) promoted 2-diethylaminoethanol (DEAE) aqueous solution was investigated at temperatures ranging from (303.2 to 323.2) K. The mass fraction and temperature dependences of the saturated solubility and CO_2 loading are illustrated. The viscosities of both CO_2-unloaded and CO_2-loaded DEAE–MEA aqueous solutions were measured and then calculated by using the Weiland equation. The effects of temperature, mass fraction and CO_2 loading on viscosities are demonstrated.

Radiation resistance of organic azo dyes in aqueous solutions

International Nuclear Information System (INIS)

Khabarov, V.N.; Kozlov, L.L.

1987-01-01

The resistance to the action of the ionizing radiation of aqueous and aqueous-alcoholic solutions of organic mono- and diazo dyes was studied. The radiation chemical yield of decolorization of the dye, determined from the kinetic decolorization curves served as a quantitative criterion of the radiation resistance. The influence of pH, addition of ethanol, hydroquinone, thiourea, glucose and oxygen on the radiation resistance of the azo dyes was studied. An attempt was made to relate the efficiency of radiation decolorization to the chemical nature of the dye

An introduction to radiation induced degradation of biological molecules in aqueous solutions

International Nuclear Information System (INIS)

Lal, Manohar

1991-01-01

Radiation chemistry of aqueous systems is the chemistry of H, OH, e aq - , H 3 O + and H 2 O * formed when a solute in aqueous solutions is exposed to ionising radiation. The pulse radiolysis technique has helped in the production, the detection and understanding of the reactions of primary species with solutes. A great deal of data on radiation biochemical studies e.g. degradation of DNA, its constituents and their protection, radiation protection and sensitisation, generation of superoxide ion and their reactions has already been reported but a great deal still needs to be done for the understanding of radiation biology. (author). 12 refs

Ammonia complexes of metals in aqueous solutions with high concentrations of ammonia

International Nuclear Information System (INIS)

Padar, T.G.; Novikov, L.K.; Stupko, T.V.; Isaev, I.D.; Pashkov, G.L.; Mironov, V.E.

1991-01-01

Potentiometric method, glass electrodes and Bierrum function were used to study the formation of ammonia complexes of magnesium, calcium, cadmium, zinc, copper(2) and silver in 2.0 mol/dm 3 aqueous solutions of ammonia nitrate with 0-18 mol/dm 3 ammonia concentrations at 25.0 deg C. Step constants of stability of studied complexes were calculated and their compositions were determined with account of nonideal character of aqueous-salt solutions with ammonia concentrations above 1.0 mol/dm 3 . Values of correction effects on salting out ammonia action for Bierrum function in solutions with 1.0-18 mol/dm 3 ammonia concentrations were found

Characterization of nanocomposites produced from aqueous mini emulsion containing silver nanoparticles

International Nuclear Information System (INIS)

Reis, Milvia O.; Orefice, Rodrigo L.

2011-01-01

nanocomposites based on butyl acrylate and styrene monomers were synthesized through the process of free radical polymerization in miniemulsion. An aqueous solution of silver nanoparticles was synthesized and incorporated as the continuous phase (aqueous) to the dispersed phase (oil). To this mixture was added the hydrophobic agent hexadecane and subject to thermodynamic stabilization bu ultrasonification. The nanocomposite films were characterized by FTIR and XRF and their thermal properties evaluated by DSC and TGA. (author)

Spectroscopic characterization of Greek dolomitic marble surface interacted with uranium and thorium in aqueous solutions

International Nuclear Information System (INIS)

Godelitsas, A.; Kokkoris, M.; Chatzitheodoridis, E.; Misaelides, P.

2008-01-01

The surface of a typical Greek (Thassian) dolomitic marble was studied after interaction with U- and Th-containing aqueous solutions (1000 mg/L, free-drift experiments for 1 week at atmospheric P CO 2 ), using 12 C-RBS and Laser μ-Raman spectroscopy. Powder-XRD and SEM-EDS were also applied to investigate the phases deposited on the surface of the interacted samples. The obtained results indicated a considerable removal of U from the aqueous medium mainly due to massive surface precipitation of amorphous UO 2 -hydroxide phases forming a relatively thick (μm-sized) coating on the carbonate substrate. The interaction of Th with dolomitic marble surface is also intense leading to a formation of an amorphous Th-hydroxide layer of similar thickness but of significantly lower elemental atomic proportion

Spectroscopic characterization of Greek dolomitic marble surface interacted with uranium and thorium in aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Godelitsas, A. [Faculty of Geology and Geoenvironment, University of Athens, 15784 Zographou, Athens (Greece)], E-mail: agodel@geol.uoa.gr; Kokkoris, M. [School of Applied Mathematics and Physics, National Technical University of Athens, 15780 Zographou, Athens (Greece); Chatzitheodoridis, E. [School of Mining and Metallurgical Engineering, National Technical University of Athens, 15780 Zographou, Athens (Greece); Misaelides, P. [Faculty of Chemistry, Aristotle University of Thessaloniki, 54124 Thessaloniki (Greece)

2008-05-15

The surface of a typical Greek (Thassian) dolomitic marble was studied after interaction with U- and Th-containing aqueous solutions (1000 mg/L, free-drift experiments for 1 week at atmospheric P{sub CO{sub 2}}), using {sup 12}C-RBS and Laser {mu}-Raman spectroscopy. Powder-XRD and SEM-EDS were also applied to investigate the phases deposited on the surface of the interacted samples. The obtained results indicated a considerable removal of U from the aqueous medium mainly due to massive surface precipitation of amorphous UO{sub 2}-hydroxide phases forming a relatively thick ({mu}m-sized) coating on the carbonate substrate. The interaction of Th with dolomitic marble surface is also intense leading to a formation of an amorphous Th-hydroxide layer of similar thickness but of significantly lower elemental atomic proportion.

Spectroscopic characterization of Greek dolomitic marble surface interacted with uranium and thorium in aqueous solutions

Science.gov (United States)

Godelitsas, A.; Kokkoris, M.; Chatzitheodoridis, E.; Misaelides, P.

2008-05-01

The surface of a typical Greek (Thassian) dolomitic marble was studied after interaction with U- and Th-containing aqueous solutions (1000 mg/L, free-drift experiments for 1 week at atmospheric PCO2), using 12C-RBS and Laser μ-Raman spectroscopy. Powder-XRD and SEM-EDS were also applied to investigate the phases deposited on the surface of the interacted samples. The obtained results indicated a considerable removal of U from the aqueous medium mainly due to massive surface precipitation of amorphous UO2-hydroxide phases forming a relatively thick (μm-sized) coating on the carbonate substrate. The interaction of Th with dolomitic marble surface is also intense leading to a formation of an amorphous Th-hydroxide layer of similar thickness but of significantly lower elemental atomic proportion.

A thermodynamic study of glucose and related oligomers in aqueous solution: Vapor pressures and enthalpies of mixing

DEFF Research Database (Denmark)

Cooke, S.A.; Jonsdottir, Svava Osk; Westh, Peter

2002-01-01

Vapor pressures above aqueous solutions of glucose and maltose at both 298.06 K and 317.99 K and vapor pressures above aqueous solutions of cellobiose, maltotriose, maltotetraose, and maltopentaose at 317.99 K have been measured. The excess enthalpies have been recorded for all of the above-menti...... in aqueous solution. This so-called transference principle is found to be of interest in furthering the discussion concerning the applicability of lattice-based models for solution theory....

Dynamic nuclear-polarization studies of paramagnetic species in solution

International Nuclear Information System (INIS)

Glad, W.E.

1982-07-01

Dynamic Nuclear Polarization (DNP) was used to measure the electron spin lattice relaxation times, T 1 , of transition metal ions in aqueous solution. Saturation which is induced in the electron spin system is transferred to the solvent proton spins by dipole-dipole interactions. The change in the polarization of the proton spins is much larger than it is in the electron spins. The change in proton polarization is easily measured by proton Nuclear Magnetic Resonance (NMR). In one experimental arrangement the sample solution was continuously flowed through a microwave cavity to the NMR coil. The NMR was observed with a continuous wave NMR spectrometer. In a second arrangement the whole sample tube was moved from within the microwave cavity to the NMR coil in less than 40 ms by a blast of compressed air. The NMR was then observed with a pulse-Fourier-transform spectrometer. With the second arrangement a mean-square microwave magnetic field at the sample of more than 10 G 2 is obtainable with 14 W of microwave power. Measurements of DNP at 9 GHz were made on aqueous solutions of VO 2+ , Mn 2+ , Cr(CN) 6 3- , Cu 2+ and Cu(ethylenediamine) 2 (H 2 0) 2 2+ ions from 3 to 60 0 C. It was also possible to observe DNP on resolved proton resonances from mixed water-acetonitrile solutions of VO 2+ and Cr(CN) 6 3- ions

Hg(II) removal from aqueous solutions by bacillus subtilis biomass

Energy Technology Data Exchange (ETDEWEB)

Wang, Xue Song; Li, Fei Yan; He, Wen; Miao, Hua Hua [Department of Chemical Engineering, Huaihai Institute of Technology, Lianyungang (China)

2010-01-15

The biosorption of Hg(II) from aqueous solutions using Bacillus subtilis biomass was investigated in this study. The adsorbent was characterized by FTIR. Various factors including solution pH, initial concentration of Hg(II), contact time, reaction temperature and ionic strength were taken into account and promising results were obtained. An initial solution pH of 5.0 was most favorable for Hg(II) removal. The kinetic data was also analyzed using pseudo first order and pseudo second order equations. The results suggested that Hg(II) bioadsorption was best represented by the pseudo second order equation. Freundlich, Langmuir and Langmuir-Freundlich isotherms for the present systems were analyzed. The most satisfactory interpretation for the equilibrium data at different temperatures was given by the Langmuir-Freundlich isotherm. The effect of ionic strength on bioadsorption was significant. Bacillus subtilis biomass could serve as low cost adsorbent to remove Hg(II) from aqueous solutions, especially at lower concentrations of Hg(II) (<20 mg Hg/L). (Abstract Copyright [2010], Wiley Periodicals, Inc.)

Radiolysis of anthraquinone dyes in aqueous solutions

International Nuclear Information System (INIS)

Vysotskaya, N.A.; Bortun, L.N.; Ogurtsov, N.A.; Migdalovich, E.A.; Revina, A.A.; Volodko, V.V.; AN SSSR, Moscow. Inst. Ehlektrokhimii)

1986-01-01

The commercial anthraquinone dyes (Dark Blue, Light Blue, Green) in aqueous solutions were shown to be decoloured and degrade under the action of ionizing radiation. The degree of decolouration and degradation of aromatic rings was found to increase in presence of oxygen. Hydroxyl radicals were shown to play the key role in the degradation of the dyes under irradiation. The radiolysis intermediate products were studied using the pulse radiolysis technique. (author)

Ion spatial distributions at the liquid-vapor interface of aqueous potassium fluoride solutions

Energy Technology Data Exchange (ETDEWEB)

Brown, M A; D' Auria, R; Kuo, I W; Krisch, M J; Starr, D E; Bluhm, H; Tobias, D J; Hemminger, J C

2008-04-23

X-ray photoemission spectroscopy operating under ambient pressure conditions is used to probe ion distributions throughout the interfacial region of a free-flowing aqueous liquid micro-jet of 6 M potassium fluoride. Varying the energy of the ejected photoelectrons by carrying out experiments as a function of x-ray wavelength measures the composition of the aqueous-vapor interfacial region at various depths. The F{sup -} to K{sup +} atomic ratio is equal to unity throughout the interfacial region to a depth of 2 nm. The experimental ion profiles are compared with the results of a classical molecular dynamics simulation of a 6 M aqueous KF solution employing polarizable potentials. The experimental results are in qualitative agreement with the simulations when integrated over an exponentially decaying probe depth characteristic of an APPES experiment. First principles molecular dynamics simulations have been used to calculate the potential of mean force for moving a fluoride anion across the air-water interface. The results show that the fluoride anion is repelled from the interface, and this is consistent with the depletion of F{sup -} at the interface revealed by the APPES experiment and polarizable force field-based molecular dynamics simulation. Together, the APPES and MD simulation data provide a detailed description of the aqueous-vapor interface of alkali fluoride systems. This work offers the first direct observation of the ion distribution at a potassium fluoride aqueous solution interface. The current experimental results are compared to those previously obtained for saturated solutions of KBr and KI to underscore the strong difference in surface propensity between soft/large and hard/small halide ions in aqueous solution.

Opto-electrochemical spectroscopy of metals in aqueous solutions

International Nuclear Information System (INIS)

Habib, K.

2016-01-01

In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the electrical resistance of aluminium samples during the initial stage of anodisation processes in aqueous solution. In fact, because the resistance values in this investigation were obtained by holographic interferometry, electromagnetic method rather than electronic method, the abrupt rate change of the resistance was called electrical resistance–emission spectroscopy. The anodisation process of the aluminium samples was carried out by electrochemical impedance spectroscopy (EIS) in different sulphuric acid concentrations (1.0%–2.5% H 2 SO 4 ) at room temperature. In the meantime, the real time holographic interferometry was used to determine the difference between the electrical resistance of two subsequent values, dR, as a function of the elapsed time of the EIS experiment for the aluminium samples in 1.0%, 1.5%, 2.0%, and 2.5% H 2 SO 4 solutions. The electrical resistance–emission spectra of the present investigation represent a detailed picture of not only the rate change of the electrical resistance throughout the anodisation processes but also the spectra represent the rate change of the growth of the oxide films on the aluminium samples in different solutions. As a result, a new spectrometer was developed based on the combination of the holographic interferometry and electrochemical impedance spectroscopy for studying in situ the electrochemical behavior of metals in aqueous solutions.

Detection of hypoxanthine, xanthine and uric acid in γ-irradiated aqueous solution of cytosine

International Nuclear Information System (INIS)

Kobayashi, Tsuya; Shirai, Kazuo

1979-01-01

The aqueous solution of cytosine of 3.6 x 10 -2 M was irradiated with gamma -ray (60 megarad) in nitrogen-saturated glass ampules, and freeze-dried, then the residue obtained was changed to trimethylsilylacid, and this was analyzed by paper chromatography, UV spectrometry, and/or gas-liquid chromatography. Hypoxanthine, xanthine and uric acid were detected in this solution, in addition to some other compounds already known to be produced by gamma -irradiation, e.g., TMS-uracil, TMS-6-hydroxyuracil and TMS-hypoxanthine. It was presumed that these compounds were formed by the recombination of the primary radiolytic products. Uric acid formation by this mechanism was confirmed by gamma -irradiation of the mixture that contained urea, and 5- and 6-hydroxyuracil. (Kaihara, S.)

Extraction of hafnium with chelating agents from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

The extraction was studied of hafnium into solutions of N-benzoyl-N-phenylhydroxylamine, 2-thenoyltrifluoroacetone and di-n-butylphosphoric acid in benzene, toluene, chloroform and tetrachloromethane from aqueous alcoholic solutions with a formal acidity of 2M-HClO 4 . Methyl-, ethyl-, n- and isopropyl- and tert-butyl alcohol were used as organic components in the mixed aqueous-organic phase. In the extraction into N-benzoyl-N-phenylhydroxylamine the presence of the alcohols resulted in synergic effects analogous to the previously described extraction by substituted benzoylpyrazolone. With the other two extractants, the effect of the alcohols was antagonistic, due to the interaction of alcohol or water with the reagent in the organic phase, and to the decrease in the reagent distribution constant. (author)

[Extraction of lambda-cyhalothrin from aqueous dioxan solutions].

Science.gov (United States)

Shormanov, V K; Chigareva, E N; Belousova, O V

2011-01-01

The results of extraction of lambda-cigalotrin from dioxan aqueous solutions by hydrophobic organic solvents are presented. It is shown that the degree of extraction depends on the nature of the extractant, the water to dioxan ratio, and saturation of the water-dioxan layer with the electrolyte. The highest efficiency of lambda-cigalotrin extraction was achieved using chlorophorm as a solvent under desalination conditions. The extraction factor was calculated necessary to obtain the desired amount of lambda-cigalotrin from the water-dioxan solution (4:1) with the help of the extractants being used.

NMR study of thermoresponsive block copolymer in aqueous solution

Czech Academy of Sciences Publication Activity Database

Spěváček, Jiří; Konefal, Rafal; Čadová, Eva

2016-01-01

Roč. 217, č. 12 (2016), s. 1370-1375 ISSN 1022-1352 R&D Projects: GA ČR(CZ) GA15-13853S Institutional support: RVO:61389013 Keywords : aqueous solutions * NMR * NOESY Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.500, year: 2016

DETERMINATION OF CHLORHEXIDINE IN SALIVA AND IN AQUEOUS-SOLUTIONS

NARCIS (Netherlands)

de Vries, J.; Ruben, J; Arends, J.

1991-01-01

A new method is presented for the determination of chlorhexidine in centrifuged saliva and in aqueous solutions by means of fluorescence spectroscopy. The method relies on complex formation between chlorhexidine and eosin. The fluorescence value of the chlorhexidine-eosin system decreases with

Electrochemistry and electrogenerated chemiluminescence of films of silicon nanoparticles in aqueous solution

International Nuclear Information System (INIS)

Bae, Yoonjung; Lee, Doh C; Rhogojina, Elena V; Jurbergs, David C; Korgel, Brian A; Bard, Allen J

2006-01-01

Films of octadecyl-capped Si nanoparticles (NPs) (diameter, 3.4 ± 0.7 nm) prepared by drop-coating on indium tin oxide (ITO) showed electrogenerated chemiluminescence (ECL) for both cathodic and anodic potential sweeps in KOH solutions containing peroxydisulfate. The redox potentials of the Si NPs can be estimated as approximately -0.9 and +0.95 V (versus Ag|AgCl) based on the anodic potential for the onset of ECL minus the ECL peak energy. The ECL exhibits a relatively broad spectrum (FWHM = 160 nm) with a peak wavelength of ∼670 nm (1.85 eV), similar to the photoluminescence spectra. In electrochemical studies in KOH solution in the absence of peroxydisulfate, an anodic current peak appears at about -1 V (versus Ag|AgCl) following a scan to negative potentials. A similar peak has been observed during the etching of a bulk single crystal Si electrode in alkaline aqueous solution. Unpassivated surface sites of Si NPs seem to be etched at potentials negative of the anodic oxidation peak

An effective colorimetric and ratiometric fluorescent probe for bisulfite in aqueous solution

International Nuclear Information System (INIS)

Dai, Xi; Zhang, Tao; Du, Zhi-Fang; Cao, Xiang-Jian; Chen, Ming-Yu; Hu, Sheng-Wen; Miao, Jun-Ying; Zhao, Bao-Xiang

2015-01-01

We have developed the first two-photon colorimetric and ratiometric fluorescent probe, BICO, for the detection of bisulfite (HSO 3 − ) in aqueous solution. The probe contains coumarin and benzimidazole moieties and can detect HSO 3 − based on the Michael addition reaction with a limit of detection 5.3 × 10 −8  M in phosphate-buffered saline solution. The probe was used to detect bisulfite in tap water, sugar and dry white wine. Moreover, test strips were made and used easily. We successfully applied the probe to image living cells, using one-photon fluorescence imaging. BICO overcomes the limitations in sensitivity of previously reported probes and the solvation effect of bisulfite, which demonstrates its excellent value in practical application. - Highlights: • A colorimetric and ratiometric fluorescent probe was developed. • The probe could detect bisulfite in PBS buffer solution and real samples. • Bisulfite test paper was made to naked-eye detect bisulfite. • This probe successfully used to living cell imaging in ratiometric manner

An effective colorimetric and ratiometric fluorescent probe for bisulfite in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Dai, Xi [Institute of Organic Chemistry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Zhang, Tao [Institute of Developmental Biology, School of Life Science, Shandong University, Jinan 250100 (China); Du, Zhi-Fang; Cao, Xiang-Jian; Chen, Ming-Yu [Institute of Organic Chemistry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Taishan College, Shandong University, Jinan 250100 (China); Hu, Sheng-Wen [Institute of Organic Chemistry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China); Miao, Jun-Ying, E-mail: miaojy@sdu.edu.cn [Institute of Developmental Biology, School of Life Science, Shandong University, Jinan 250100 (China); Zhao, Bao-Xiang, E-mail: bxzhao@sdu.edu.cn [Institute of Organic Chemistry, School of Chemistry and Chemical Engineering, Shandong University, Jinan 250100 (China)

2015-08-12

We have developed the first two-photon colorimetric and ratiometric fluorescent probe, BICO, for the detection of bisulfite (HSO{sub 3}{sup −}) in aqueous solution. The probe contains coumarin and benzimidazole moieties and can detect HSO{sub 3}{sup −} based on the Michael addition reaction with a limit of detection 5.3 × 10{sup −8} M in phosphate-buffered saline solution. The probe was used to detect bisulfite in tap water, sugar and dry white wine. Moreover, test strips were made and used easily. We successfully applied the probe to image living cells, using one-photon fluorescence imaging. BICO overcomes the limitations in sensitivity of previously reported probes and the solvation effect of bisulfite, which demonstrates its excellent value in practical application. - Highlights: • A colorimetric and ratiometric fluorescent probe was developed. • The probe could detect bisulfite in PBS buffer solution and real samples. • Bisulfite test paper was made to naked-eye detect bisulfite. • This probe successfully used to living cell imaging in ratiometric manner.

The radiolytic reduction of mercuric chloride in aqueous sugar solutions

International Nuclear Information System (INIS)

Johnston, F.J.

1991-01-01

The reduction of HgCl 2 has been measured in Co-60 γ-irradiated aqueous glucose, fructose and sucrose solutions. G-values for reduction, G(R), are substantially greater than 6 molecules per 100 eV in all systems from 1% by weight sugar to greater than 50%. Chain reduction occurs in glucose and fructose solutions with maximum G(R) values of 18-20 molecules per 100 eV occurring at 24% (1.0 M) sugar. The results are consistent with a mechanism in which HgCl radicals react with the organic solute to produce chain propagating free radicals. A dose rate independence of the chain length, after a brief ''induction'' period, is explained in terms of a chain termination by the incorporation of HgCl in growing Hg 2 Cl 2 particles. Reduction of Ag(I) and Cu(II) in aqueous sucrose and fructose systems took place with G(R) < 6 indicating the absence of reaction chains in these cases. (author)

The vapour pressure of water as a function of solute concentration above aqueous solutions of fructose, sucrose, raffinose, erythritol, xylitol, and sorbitol

DEFF Research Database (Denmark)

Cooke, S.A.; Jonsdottir, Svava Osk; Westh, Peter

2002-01-01

The vapour pressure of water above an aqueous solution of sucrose at T = 298.06 K has been measured for 9 sucrose mole fractions up to 0.12. Vapour pressure measurements have also been made on aqueous solutions of meso-erythritol, xylitol, sorbitol, fructose, and raffinose at T = 317.99 K...

Pinning of phase separation of aqueous solution of hydroxypropylmethylcellulose by gelation

Science.gov (United States)

Kita, Rio; Kaku, Takeshi; Kubota, Kenji; Dobashi, Toshiaki

1999-08-01

Opalescence of the aqueous solution of hydroxypropylmethylcellulose (HPMC) induced by heating has been studied in terms of the phase diagram and the phase separation dynamics. The cloud point curve and the sol-to-gel transition curve intersected with each other at about 55 °C. Just above the cloud-point curve at which the spinodal curve has its minimum, a ring-like scattering pattern appeared corresponding to the spinodal decomposition. Temporal growth of the scattering function in the course of phase separation was studied by a time-resolved light scattering technique. The gelation pinned the phase separation (spinodal decomposition) of the aqueous HPMC solution.

A procedure for preferential trapping of cesium cations from aqueous solutions and their separation from other inorganic cations

International Nuclear Information System (INIS)

Plesek, J.; Hermanek, S.; Selucky, P.; Williams, R.E.

1995-01-01

The title procedure is as follows. Deltahedral heteroborane anions are added to the aqueous solution containing cesium ions, precipitate (if any) is separated off, and the cesium salts involving the deltahedral heteroborane anions are trapped on activated carbon. The cobaltocarborane anion [3-Co-(1,2-C 2 B 9 H 11 ) 2 ] and/or its substitution derivatives are particularly well suited to this purpose. The process can find use in the separation of radionuclides present in waste solutions arising from spent nuclear fuel treatment. (P.A.). 1 fig

Density functional theory-based prediction of the formation constants of complexes of ammonia in aqueous solution: indications of the role of relativistic effects in the solution chemistry of gold(I).

Science.gov (United States)

Hancock, Robert D; Bartolotti, Libero J

2005-10-03

A prediction of the formation constants (log K1) for complexes of metal ions with a single NH3 ligand in aqueous solution, using quantum mechanical calculations, is reported. DeltaG values at 298 K in the gas phase for eq 1 (DeltaG(DFT)) were calculated for 34 metal ions using density functional theory (DFT), with the expectation that these would correlate with the free energy of complex formation in aqueous solution (DeltaG(aq)). [M(H2O)6]n+(g) + NH(3)(g) = [M(H2O)5NH3]n+(g) + H2O(g) (eq 1). The DeltaG(aq) values include the effects of complex changes in solvation on complex formation, which are not included in eq 1. It was anticipated that such changes in solvation would be constant or vary systematically with changes in the log K(1) value for different metal ions; therefore, simple correlations between DeltaG(DFT) and DeltaG(aq) were sought. The bulk of the log K1(NH3) values used to calculate DeltaG(aq) were not experimental, but estimated previously (Hancock 1978, 1980) from a variety of empirical correlations. Separate linear correlations between DeltaG(DFT) and DeltaG(aq) for metal ions of different charges (M2+, M3+, and M4+) were found. In plots of DeltaG(DFT) versus DeltaG(aq), the slopes ranged from 2.201 for M2+ ions down to 1.076 for M4+ ions, with intercepts increasing from M2+ to M4+ ions. Two separate correlations occurred for the M3+ ions, which appeared to correspond to small metal ions with a coordination number (CN) of 6 and to large metal ions with a higher CN in the vicinity of 7-9. The good correlation coefficients (R) in the range of 0.97-0.99 for all these separate correlations suggest that the approach used here may be the basis for future predictions of aqueous phase chemistry that would otherwise be experimentally inaccessible. Thus, the log K1(NH3) value for the transuranic Lr3+, which has a half-life of 3.6 h in its most stable isotope, is predicted to be 1.46. These calculations should also lead to a greater insight into the factors

Solubility of some phenolic compounds in aqueous alkali metal nitrate solutions from (293.15 to 318.15) K

Energy Technology Data Exchange (ETDEWEB)

Noubigh, Adel [Laboratoire de Physico-chimie des materiaux, IPEST, BP51, 2070 La MARSA (Tunisia)], E-mail: Adel.anoubigh@ipest.rnu.tn; Cherif, Mourad [IPEIEM, Universite de Tunis-El Manar, BP244. 2096. El Manar II (Tunisia); Provost, Elise [Laboratoire Chimie et procedes, ENSTA, 32 Rue de Boulevard Victor, 75739 Paris, Cedex 15 (France); Abderrabba, Manef [Laboratoire de Physico-chimie des materiaux, IPEST, BP51, 2070 La MARSA (Tunisia)

2008-11-15

This paper is continuation of the study concerning the solubility-temperature dependence data for some phenolic compounds (PhC), contained in olive mill wastewater (OMWW), in two nitrate salts (KNO{sub 3} and NaNO{sub 3}) aqueous solutions. The solubilities of PhC were determined in the temperature ranging from (293.15 to 318.15) K. It has been observed that the solubility, in aqueous nitrate solutions, increases with increasing temperature. Results showed that alkali metal nitrate has a salting-out effect on the solubility of PhC. The effect of the anion of the electrolyte on the solubility of PhC is observed by comparing these results with values reported in the previous papers for the effect of LiCl, NaCl and KCl. For each cation, the solubilites of the phenolic compounds are higher with nitrate anion than with chloride anion. Results were interpreted in terms of the salt hydration shells and the ability of the solute to form hydrogen-bond with water. The solubility data were accurately correlated by a semi empirical equation. The standard molar Gibbs free energies of transfer of PhC ({delta}{sub tr}G{sup 0}) from pure water to aqueous solutions of the nitrate salts have been calculated from the solubility data. The decrease in solubility is correlated to the positive {delta}{sub tr}G{sup 0} value which is mainly of enthalpic origin.

Biosorption of nickel (II) ions from aqueous solutions by tapioca peel ...

African Journals Online (AJOL)

Tapioca peel, waste from native tapioca starch industry in Thailand, was used for the biosorption of nickel from aqueous solution. The experimental parameter focuses on the influence of contact time, solution pH, initial concentration and temperature using batch experiments. The results indicated that the biosorption ...

Removal of fluoride ions from aqueous solution by waste mud

International Nuclear Information System (INIS)

Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal; Soylak, Mustafa

2009-01-01

The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

Flash and Continuous Photolysis Studies of the Thionitrosyl Complex Cr(CH3CN)5(NS)2+ and the Nitric Oxide Analogs. Reactions of Nitrogen Monosulfide in Solution

DEFF Research Database (Denmark)

Dethlefsen, Johannes Wied; Hedegård, Erik; Rimmer, R. Dale

2009-01-01

Photolysis of the thionitrosyl complex Cr(CH3CN)5(NS)2+ (1) in acetonitrile solution leads to the dissociation of nitrogen monosulfide (NS).  In deaerated solution, this reaction is reversible, and flash photolysis studies demonstrate that NS reacts with Cr(CH3CN)62+ according to the rate law d[1...... dependent quantum yields of 0.3-1.0 mol/Einstein. Mass spectroscopic studies of the product solutions demonstrate formation of S8, presumably from the decomposition of NS. The quantitative photochemical behaviors of 1 and the nitrosyl analog 2 are compared. Udgivelsesdato: Jan....

NIR spectroscopic properties of aqueous acids solutions.

Science.gov (United States)

Omar, Ahmad Fairuz; Atan, Hanafi; Matjafri, Mohd Zubir

2012-06-15

Acid content is one of the important quality attributes in determining the maturity index of agricultural product, particularly fruits. Despite the fact that much research on the measurement of acidity in fruits through non-destructive spectroscopy analysis at NIR wavelengths between 700 to 1,000 nm has been conducted, the same response towards individual acids is not well known. This paper presents NIR spectroscopy analysis on aqueous citric, tartaric, malic and oxalic solutions through quantitative analysis by selecting a set of wavelengths that can best be used to measure the pH of the solutions. The aquaphotomics study of the acid solutions has generated R² above 0.9 for the measurement of all acids. The most important wavelengths for pH are located at 918-925 nm and 990-996 nm, while at 975 nm for water.

Aqueous solutions of acidic ionic liquids for enhanced stability of polyoxometalate-carbon supercapacitor electrodes

Science.gov (United States)

Hu, Chenchen; Zhao, Enbo; Nitta, Naoki; Magasinski, Alexandre; Berdichevsky, Gene; Yushin, Gleb

2016-09-01

Nanocomposites based on polyoxometalates (POMs) nanoconfined in microporous carbons have been synthesized and used as electrodes for supercapacitors. The addition of the pseudocapacitance from highly reversible redox reaction of POMs to the electric double-layer capacitance of carbon lead to an increase in specific capacitance of ∼90% at 1 mV s-1. However, high solubility of POM in traditional aqueous electrolytes leads to rapid capacity fading. Here we demonstrate that the use of aqueous solutions of protic ionic liquids (P-IL) as electrolyte instead of aqueous sulfuric acid solutions offers an opportunity to significantly improve POM cycling stability. Virtually no degradation in capacitance was observed in POM-based positive electrode after 10,000 cycles in an asymmetric capacitor with P-IL aqueous electrolyte. As such, POM-based carbon composites may now present a viable solution for enhancing energy density of electrical double layer capacitors (EDLC) based on pure carbon electrodes.

Durability of API class B cement pastes exposed to aqueous solutions containing chloride, sulphate and magnesium ions

Directory of Open Access Journals (Sweden)

Hernández, M. E.

2008-12-01

Full Text Available This paper discusses a durability study conducted on API class B cement, the type used in shallow oil wells, when exposed to aggressive formation water. Its resistance to the major ions, namely –SO4=, Mg+2 and Cl-–, is related both to its capacity to assimilate the aggressive action of each harmful agent and to the changes in the chemical reactivity of some of its components. The methodology used consisted in preparing and immersing cement specimens in neutral solutions containing variable concentrations of these ions to monitor the chemical reactions taking place. These solutions were analyzed and XRD studies were conducted for over a year to identify mineralogical variations. The purposes of the study were to determine the effects of joint ionic attack on this kind of cement and to monitor the variations in the calcium concentration in the aqueous solutions of Na2SO4, MgCl2 and NaCl in contact with API class B cement pastesEste trabajo se basa en el estudio de la durabilidad de un cemento API clase B, utilizado en pozos petrolíferos someros, frente a la agresividad de las aguas de formación a las que puede estar expuesto. Su eficacia frente a la exposición a los iones más importantes –SO4=, Mg+2 y Cl-– se relaciona con su capacidad de asimilar la acción agresiva de cada agente perjudicial, así como de las reacciones químicas que sufra por la reactividad de alguno de sus compuestos. La metodología aplicada supone la preparación de probetas de este cemento y su inmersión en disoluciones neutras, conteniendo los referidos iones a distintas concentraciones, para evaluar el desarrollo de las reacciones existentes en su seno. A tal fin se realizaron análisis de las disoluciones y estudios de DRX durante más de un año para conocer su evolución mineralógica. El objetivo del trabajo ha sido determinar los efectos resultantes de los ataques conjuntos de los citados iones al referido cemento; así como la observación de las

Removal of phosphate and nitrate from aqueous solution using ...

African Journals Online (AJOL)

The aim of the present study was the removal of phosphate and nitrate by sodium alginate seagrass (Cymodocea rotundata) beads from aqueous solutions. The adsorption characteristics of phosphate and nitrate on the seagrass beads were optimized under different operational parameters like adsorbent dosage, initial ...

Synthesis and molecular structure of [Cu(NH3)4][Ni(CN)4]: A missing piece in the [Cu(NH3)n][Ni(CN)4] story

Science.gov (United States)

Solanki, Dina; Hogarth, Graeme

2015-11-01

Reaction of CuCl2·2H2O and K2[Ni(CN)4]·2H2O in aqueous ammonia gave blue rod-like crystals of [Cu(NH3)4][Ni(CN)4]. An X-ray crystallographic reveals that square-planar anions and cations are weakly associated through coordination of a cis pair of cyanide ligands to copper, with one short and one long contact and thus the copper centre is best described as a square-based pyramid. Crystals lose ammonia readily upon removal from the solvent and this has been probed by TGA and DSC measurements. For comparison we have also re-determined the structure of the related ethylenediamine (en) complex [Cu(en)2][Ni(CN)4] at 150 K. This consists of a 1D chain in which a trans pair of cyanide ligands bind to copper such that the latter has an overall tetragonally distorted octahedral coordination geometry.

Acidities of Water and Methanol in Aqueous Solution and DMSO

Science.gov (United States)

Gao, Daqing

2009-01-01

The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

The green synthesis of fine particles of gold using an aqueous extract of Monotheca buxifolia (Flac.)

Science.gov (United States)

Anwar, Natasha; Khan, Abbas; Shah, Mohib; Azam, Andaleeb; Zaman, Khair; Parven, Zahida

2016-12-01

This study deals with the synthesis and physicochemical investigation of gold nanoparticles using an aqueous extract of Monotheca buxifolia (Flac.). On the treatment of aqueous solution of tetrachloroauric acid with the plant extract, gold nanoparticles were rapidly fabricated. The synthesized particles were characterized by UV-Vis spectrophotometry (UV), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray (EDX) and Scanning electron microscopy (SEM). The formation of AuNPs was confirmed by noting the change in color through visual observations as well as via UV-Vis spectroscopy. UV‒Vis spectrum of the aqueous medium containing gold nanoparticles showed an absorption peak at around 540 nm. FTIR was used to identify the chemical composition of gold nanoparticles and Au-capped plant extract. The presence of elemental gold was also confirmed through EDX analysis. SEM analysis of the gold nanoparticles showed that they have a uniform spherical shape with an average size in the range of 70-78 nm. This green system showed to be better capping and stabilizing agent for the fine particles. Further, the antioxidant activity of Monotheca buxifolia (Flac.) extract and Au-capped with the plant extract was also evaluated using FeCl3/K3[Fe(CN)]6 in vitro assay.

Adsorption of Pb(II) ions from aqueous solution using lignin from ...

African Journals Online (AJOL)

The adsorption of lead(II) ions from aqueous solution onto alkali lignin extracted from Hagenia abyssinica was investigated by electrochemical methods. The effect of solution pH, lignin dosage and contact time were investigated at room temperature in a batch system. Adsorption equilibrium was approached within 80 min.

KDP Aqueous Solution-in-Oil Microemulsion for Ultra-Precision Chemical-Mechanical Polishing of KDP Crystal

Directory of Open Access Journals (Sweden)

Hui Dong

2017-03-01

Full Text Available A novel functional KH2PO4 (KDP aqueous solution-in-oil (KDP aq/O microemulsion system for KDP crystal ultra-precision chemical-mechanical polishing (CMP was prepared. The system, which consisted of decanol, Triton X-100, and KH2PO4 aqueous solution, was available at room temperature. The functional KDP aq/O microemulsion system was systematically studied and applied as polishing solution to KDP CMP technology. In this study, a controlled deliquescent mechanism was proposed for KDP polishing with the KDP aq/O microemulsion. KDP aqueous solution, the chemical etchant in the polishing process, was caged into the micelles in the microemulsion, leading to a limitation of the reaction between the KDP crystal and KDP aqueous solution only if the microemulsion was deformed under the effect of the external force. Based on the interface reaction dynamics, KDP aqueous solutions with different concentrations (cKDP were applied to replace water in the traditional water-in-oil (W/O microemulsion. The practicability of the controlled deliquescent mechanism was proved by the decreasing material removal rate (MRR with the increasing of the cKDP. As a result, the corrosion pits on the KDP surface were avoided to some degree. Moreover, the roughnesses of KDP with KDP aq/O microemulsion (cKDP was changed from 10 mM to 100 mM as polishing solutions were smaller than that with the W/O microemulsion. The smallest surface root-mean-square roughness of 1.5 nm was obtained at a 30 mmol/L KDP aq solution, because of the most appropriate deliquescent rate and MRR.

Fast heavy-ion radiation damage of glycine in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Nomura, Shinji [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8530 (Japan); Tsuchida, Hidetsugu, E-mail: tsuchida@nucleng.kyoto-u.ac.jp [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8530 (Japan); Quantum Science and Engineering Center, Kyoto University, Uji 611-0011 (Japan); Furuya, Ryosuke [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8530 (Japan); Majima, Takuya; Itoh, Akio [Department of Nuclear Engineering, Kyoto University, Kyoto 615-8530 (Japan); Quantum Science and Engineering Center, Kyoto University, Uji 611-0011 (Japan)

2016-12-15

Fast heavy-ion radiolysis of biomolecules in aqueous solution is investigated for an atomistic understanding of radiation damage to normal cells during heavy-particle beam therapy. The smallest amino acid glycine was used as a model biomaterial. Microjets of aqueous glycine solutions under vacuum were irradiated with 4.0-MeV carbon ions corresponding to energies in the Bragg peak region. To understand the effects of the water environment on molecular damage, the yield of glycine dissociation was measured by secondary ion mass spectroscopy. The yield was significantly reduced relative to gas-phase glycine targets. This implies that the numerous water molecules surrounding a single glycine molecule act as a buffer that suppresses dissociation. This is an environmental effect similar to that observed for other biomolecular cluster targets.

Effect of temperature on the behavior of surface properties of alcohols in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Romero, Carmen M. [Facultad de Ciencias, Universidad Nacional de Colombia, Bogota (Colombia)], E-mail: cmromeroi@unal.edu.co; Jimenez, Eulogio [Facultade de Ciencias, Universidade da Coruna (Spain); Suarez, Felipe [Facultad de Ciencias, Universidad Nacional de Colombia, Bogota (Colombia)

2009-04-15

The influence of temperature on the behavior of surface properties of aqueous solutions has often been used to obtain information about solute structural effects on water. In this work, we present experimental results for surface tension of aqueous solutions of n-pentanol, n-hexanol, n-heptanol, and n-octanol at T = (283.15, 288.15, 293.15, 298.15, 303.15, and 308.15) K at several concentrations. The results were used to evaluate the limiting experimental slopes of surface tension with respect to mole fraction and the hydrophobicity constant of the Connors model at each temperature. The thermodynamic behavior of aqueous alcohol solutions is discussed in terms of the effect of the hydrocarbon chain on water structure. The temperature dependence of the limiting slopes of surface tension with respect to mole fraction, as well as the hydrophobicity constant derived from surface measurements, is interpreted in terms of alcohol hydration.

Effect of temperature on the behavior of surface properties of alcohols in aqueous solution

International Nuclear Information System (INIS)

Romero, Carmen M.; Jimenez, Eulogio; Suarez, Felipe

2009-01-01

The influence of temperature on the behavior of surface properties of aqueous solutions has often been used to obtain information about solute structural effects on water. In this work, we present experimental results for surface tension of aqueous solutions of n-pentanol, n-hexanol, n-heptanol, and n-octanol at T = (283.15, 288.15, 293.15, 298.15, 303.15, and 308.15) K at several concentrations. The results were used to evaluate the limiting experimental slopes of surface tension with respect to mole fraction and the hydrophobicity constant of the Connors model at each temperature. The thermodynamic behavior of aqueous alcohol solutions is discussed in terms of the effect of the hydrocarbon chain on water structure. The temperature dependence of the limiting slopes of surface tension with respect to mole fraction, as well as the hydrophobicity constant derived from surface measurements, is interpreted in terms of alcohol hydration

Electronic structure tautomerism, and mechanism of H-D exchange in imidazole aqueous solutions

International Nuclear Information System (INIS)

Borisov, Yu.A.; Vorob'eva, N.P.; Abronin, I.A.; Kolomiets, A.F.

1988-01-01

The imidazole electronic structure in a gaseous phase is studied taking into account the influence of solvation effects in aqueous solutions. Possible mechanisms of tautomeric transformations and H-D exchange reactions with water molecules are discussed. Using the quantum chemistry methods, it is shown that the intramolecular mechanism of imidazole isomerization in the gaseous phase and the aqueous solution is unprofitable, and the intermolecular mechanism can proceed through the stage of protonated and carbene form formation

Adsorption of ammonium dinitramide (ADN) from aqueous solutions. 1. Adsorption on powdered activated charcoal.

Science.gov (United States)

Santhosh, G; Venkatachalam, S; Ninan, K N; Sadhana, R; Alwan, S; Abarna, V; Joseph, M A

2003-03-17

Investigations on the adsorption of ammonium dinitramide (NH(4)N(NO(2))(2)) (ADN) from aqueous solutions on powdered activated charcoal (PAC) were carried out in order to find out an effective and easier method of separating ADN from aqueous solutions. The effectiveness of PAC in the selective adsorption of ADN from aqueous solutions of ADN (ADN-F) and ADN in presence of sulfate (SO(4)(2-)) and nitrate (NO(3)(-)) ions (ADN-PS) was examined and compared using batch and column methods. The adsorption process follows both Langmuir and Freundlich adsorption isotherms and the isotherm parameters for the models were determined. The observed data favor the formation of monolayer adsorption. The adsorption capacities were found to be 63.3, 119, 105.3 and 82 mg of ADN per g of PAC for ADN-F (batch), ADN-PS (batch), ADN-F (column) and ADN-PS (column), respectively. Break-through curves for ADN-F and ADN-PS were obtained for the optimization of separation of ADN from aqueous solutions. Elution curves were generated for the desorption of ADN from PAC using hot water as eluent. Copyright 2003 Elsevier Science B.V.

Biosorptive removal of cobalt (II) ions from aqueous solution by ...

African Journals Online (AJOL)

hope&shola

2010-11-29

Nov 29, 2010 ... chemical reaction, decay, adsorption and biodegradation. The presence of ... sted coffee (Dakiky et al., 2002), waste tea (Ahluwalia and Goyal, 2005) ..... green removal from aqueous solution by citric acid modified rice straw.

Adsorption of Chromium from Aqueous Solution Using Polyaniline

Directory of Open Access Journals (Sweden)

Majid Riahi Samani

2011-10-01

Full Text Available New group of polymers have been synthesized that are conductive of electricity so they are called conducting polymers. One of the most conducting polymers is "polyaniline". In the present study, polyaniline was synthesized by oxidizing aniline monomer under strongly acidic conditions using potassium iodate as an initiator of oxidative polymerization. Synthesized polyaniline as a powder used as an adsorbent to remove chromium from aqueous solution. Experiments were conducted in batch mode with variables such as amount of polyaniline, chromium solution pH and adsorbtion isotherms. Due to presence of Cr (III in solution after using polyaniline, removal mechanism is the combination of surface adsorption and reduction. It seems that polyaniline reduces the Cr(VI to Cr(III and adsorbs the Cr(III and a part of remaining  Cr(VI. It is well known that nitrogen atom in compounds of amine derivative makes co-ordinate bond with positive charge of metals due to the presence of electron in sp3 orbital of nitrogen. The majority of total chromium removal  occurred at 30minute for polyaniline  and the optimum  time for  hexavalent chromium  removal was about 5 min. Polyaniline has the maximum total cheomiume removal at pH, 3-9. The maximum hexavalent chromium removal occurred at acidic pH for polyanilines. The equilibrium adsorption data for polyaniline fitted both Freundlich’s and Langmuir’s isotherms. This research shows that polyaniline can be used as an adsorbent  for removal chromium from aqueous solution.

Chlorite alteration in aqueous solutions and uranium removal by altered chlorite

Energy Technology Data Exchange (ETDEWEB)

Kim, Eungyeong; Ahn, Hyangsig [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 02841 (Korea, Republic of); Jo, Ho Young, E-mail: hyjo@korea.ac.kr [Department of Earth and Environmental Sciences, Korea University, Anam-dong, Seongbuk-gu, Seoul 02841 (Korea, Republic of); Ryu, Ji-Hun; Koh, Yong-Kwon [Korea Atomic Energy Research Institute, 1045 Daedeokdaero, Yuseong-gu, Daejeon 34057 (Korea, Republic of)

2017-04-05

Highlights: • Chlorite alteration and the U removal capacity of altered chlorite were investigated. • Initial pH affected more chlorite dissolution than ionic strength. • Chlorite dissolution at pH{sub o} = 3–8 was inversely proportional to the U removal capacity. • Chlorite dissolution at pH{sub o} = 10 was proportional to the U removal capacity. • The formation of Fe-containing secondary minerals affected the U removal capacity. - Abstract: Chlorite alteration and the U removal capacity of altered chlorite were investigated. Batch kinetic dissolution tests using clinochlore CCa-2 were conducted for 60 days in aqueous solutions of various pHs and ionic strengths. Batch sorption tests using these altered chlorite samples were conducted for 48 h with natural groundwater containing 3.06 × 10{sup −6} M U. Chlorite dissolution was influenced more by pH{sub o} than by the ionic strength of the solution. TEM analysis revealed Fe(oxy)hydroxide aggregates in the solid residue from the batch dissolution test with 0.1 M NaClO{sub 4} solution at pH{sub o} = 10. The U removal capacity of the reacted chlorite samples at pH{sub o} = 6–10 was higher than that of the reacted chlorite samples at pH{sub o} = 3. The degree of dissolution of chlorite samples reacted at pH{sub o} = 3–8 was inversely proportional to the U removal capacity, but that of chlorite samples reacted at pH{sub o} = 10 was proportional to the U removal capacity. The positive correlation between the U removal capacity and degree of chlorite dissolution at pH{sub o} = 10 might be due to the formation of Fe-containing secondary minerals and changes in the reactive sites.

Electrocoagulation-Adsorption to Remove Anionic and Cationic Dyes from Aqueous Solution by PV-Energy

OpenAIRE

Castañeda-Díaz, J.; Pavón-Silva, T.; Gutiérrez-Segura, E.; Colín-Cruz, A.

2017-01-01

The cationic dye malachite green (MG) and the anionic dye Remazol yellow (RY) were removed from aqueous solutions using electrocoagulation-adsorption processes. Batch and continuous electrocoagulation procedures were performed and compared. Carbonaceous materials obtained from industrial sewage sludge and commercial activated carbons were used to adsorb dyes from aqueous solutions in column systems with a 96–98% removal efficiency. The continuous electrocoagulation-adsorption system was more ...

The coacervation of aqueous solutions of tetraalkylammonium halides

International Nuclear Information System (INIS)

Mugnier de Trobriand, Anne.

1979-09-01

The coacervation of aqueous solutions of tatraalkylammonium halides in the presence of not of inorganic halides and acids has been studied, considering thermodynamic and spectroscopic aspects. The importance of dispersion forces as well as forces resulting from hydrophobic hydration has been assessed. The analogy between these systems and anionic ion exchange resins has been shown especially for Uranium VI extraction [fr

Laser Flash Photolysis and Pulse Radiolysis of Iodate and Periodate in Aqueous Solution

DEFF Research Database (Denmark)

Kläning, U K; Sehested, Knud; Wolff, Thomas

1981-01-01

photolysis study of IeVI and I0VI suggests that the predominant IeVI and I0VI species formed are IO42– and IO3 at 3 12. Redox reactions of the iodine(VI) species are fast compared with interconversion among the various iodine(VI) species......Species containing iodine in oxidation state six are formed by photolysis and radiolysis of aqueous iodate and periodate solutions in the following reactions: IO3–+ O–→ IO42–; IO3–+ OH → IO3; IVII+ eaq–→ IeVI and IVII [graphic omitted] I0VI+ O–(or OH). The present pulse radiolysis and laser flash...

Photolytic and radiolytic studies of redox processes in aqueous solutions of acridine yellow

International Nuclear Information System (INIS)

Micic, O.I.; Nenadovic, M.T.

1981-01-01

Irradiation by visible light of an aqueous solution containing acridine yellow as a sensitizer and EDTA or cysteine as an electron donor leads to the formation of reduced species which can later reduce several different electron acceptors. Methyl viologen, europium(III) salicylate, europium(III) EDTA complex or vanadium(III) salicylate were used as electron acceptors. In the presence of a catalyst reduction of water is accompanied by the evolution of hydrogen. The kinetics and mechanism of redox reactions occurring in such a system have been explored by pulse radiolysis. Optimum conditions for water reduction under continuous illumination are analysed and implications for an energy conversion system discussed. (author)

Performance of ultrasonic and hydrogen peroxide technologies in removal of Bisphenol A from Aqueous solution

Directory of Open Access Journals (Sweden)

MH Dehghani

2016-05-01

Full Text Available Introduction:BPA is a non biodegradable antioxidant that has greatly hazardous for human and animals health. and Because of the eliminating alone fewness amount of the BPA during the wastewater treatment, wastewater that contains BPA can be source of pollution in aqueous solution. The objective of this study was Performance of ultrasonic and H2O2 technologies in removal of BPA from aqueous solution. Methods:Experiments of sonochemical was carried out with use of unit ultrasonicator (Elma, which in the two power 300 and 500W, frequencies at 35 and 130KHz. Hydrogen Peroxide in concentrations at 5, 15 and 30mg/lit was applied. Initial concentration BPA at limits 2, 5, 20 and 50 mg/lit which For measuring concentration of BPA used from Spectrometer UV/VIS Lambada 25 Perkin Elmer, Shelton unit. Results:The results demonstrated that hybrid ultrasonic and peroxide Hydrogen processes with Efficiency 98.65%,  has the highest efficiency in the removal of BPA. The most decomposition rate achieved at the frequency of 130 KHz and 500W assisted by 30mg/lit H2O2 at pH 11. Also the results demonstrated that with pH increase destruction rate BPA the increased by any three processes (ultrasonic, H2O2 and both hybrid. Conclusion:The results demonstrated that hybrid ultrasonic and peroxide Hydrogen processes can be used as a clean method and friendly environment for waters treatment are contains desirable BPA.

Characterization of aqueous solution of cresol red as food irradiation dosimeter

International Nuclear Information System (INIS)

Khan, H.M.; Tabassum, S.; Wahid, M.S.

2009-01-01

Dilute aqueous solution of cresol red has been evaluated spectrophotometrically as possible gamma rays dosimeter. A 0.10 mM solution of cresol red was irradiated by gamma rays using a cobalt-60 radiation source. The absorbance spectra of the unirradiated and irradiated solutions were recorded using double beam scanning spectrophotometer. The absorbance of the solution before and after irradiation was measured at 434 nm (λ max ) as well as at other wavelengths (415, 448 and 470 nm). Various parameters, such as Absorbance (A), ΔA, %A, -log A and log A o /A i were plotted against radiation dose, in order to check the response of cresol red solution and its possible use as chemical dosimeter. The response plots of A, ΔA, and %A versus absorbed dose showed that the solution can be used as a radiation dosimeter in a dose range up to 0.82 kGy. Using response plots of -log A and log A o /A i , the useful dose range can be extended up to 1.65 kGy; which are useful dose ranges for food irradiation applications. Stability studies of cresol red solution at different light and temperature conditions for pre- and post-irradiated storage of the dosimetric solutions suggested that aqueous solution of cresol red is highly stable in dark, under fluorescence light and at room temperature up to 150 days (author)

Cast iron deterioration with time in various aqueous salt solutions

Indian Academy of Sciences (India)

Unknown

various aqueous salt solutions have been carried out using total immersion test ... circuit potential, Icorr, Tafel slopes, corrosion rate, have been calculated by standard methods. ..... Rao B V S 1980 in Maintenance for reliability (Bombay: Media.

On reactions of polymerization of p-element hydroxides in aqueous solutions

International Nuclear Information System (INIS)

Tikavyj, V.F.; Lesnikovich, A.I.

1978-01-01

The tendency of p-element hydroxides towards polymerization in aqueous solutions has been considered with respect to their location in the Periodic Table. Stable hydroxides of d-elements are practically all polymerized; among s-elements only berillium and magnesium hydroxides polymerize as the least dissociated ones. Hydroxides of the elements located to the right of the 4 Group and above the 5-th Period do not polymerize in aqueous solutions. The structure and tendency towards polymerization of In, Te, and I compounds have been studied. The tendency to polymerization of all hydroxides of p-elements located below the 4-th Period is explained from the standpoint of electron structure and the simplest thermodynamic analysis (entropy, enthalpy)

Radiolysis of benzyl alcohol in aqueous solution by external gamma-irradiation

International Nuclear Information System (INIS)

Ikebuchi, Hideharu; Kido, Yasumasa; Urakubo, Goro

1977-01-01

Radiolysis of 0.05% aqueous solution of benzyl alcohol with 60 Co γ-rays ranging from 1 x 10 4 to 7 x 10 5 rad was investigated, in order to presume the change of it contained in radiopharmaceuticals. For both O 2 free and oxygenated solutions, an approximately linear relationship holds between the retaining benzyl alcohol and dose in the range from 1 x 10 5 to 7 x 10 5 rads. The G(-M) values of benzyl alcohol calculated from the relation were 2.34 in the absence and 1.92 in presence of oxygen. In the presence of oxygen, a main product was benzaldehyde and its G value was 0.87. In the absence of oxygen, the main products of the radiolysis were dibenzyl, benzyl phenylcalbinol and hydrobenzoin, which were regarded as the radical-reaction products of PhCH 2 and PhCHOH, and the yield of benzaldehyde was negligible. Irrespective of the presence of oxygen, o- and p-hydroxylated products of benzyl alcohol were found only in small quantity. (auth.)

Biosorption of strontium ions from aqueous solution using Ca-alginate biopolymer beads

International Nuclear Information System (INIS)

Goek, C.; Aytas, S.; Gerstmann, U.

2009-01-01

Biosorption of strontium ions from aqueous solution onto calcium alginate biopolymer beads was investigated in a batch system. Ca-alginate biopolymer beads were prepared from Na-alginate via cross-linking with divalent calcium ions according to the egg box model. Optimum biosorption conditions were determined as a function of initial solution pH, initial Sr concentration, contact time, biomass dosage and temperature. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherm of Sr ions by Ca-alginate biopolymer beads. The thermodynamic parameters (ΔH, ΔS, ΔG) for Sr sorption onto biosorbent were also determined from the temperature dependence. The results indicate that this biosorbent has a good potential for removal of Sr ions from dilute aqueous solution.

21 CFR 178.1010 - Sanitizing solutions.

Science.gov (United States)

2010-04-01

... aqueous solution containing potassium iodide, sodium p-toluenesulfonchloroamide, and sodium lauryl sulfate...), trisodium phosphate (CAS Reg. No. 7601-54-9), sodium lauryl sulfate (CAS Reg. No. 151-21-3), and potassium...) An aqueous solution of citric acid, disodium ethylenediaminetetraacetate, sodium lauryl sulfate, and...

Transitions in aqueous solutions of sucrose at subzero temperatures

Czech Academy of Sciences Publication Activity Database

Sikora, Antonín; Dupanov, V. O.; Kratochvíl, Jaroslav; Zámečník, J.

2007-01-01

Roč. 46, č. 1 (2007), s. 71-85 ISSN 0022-2348 R&D Projects: GA ČR(CZ) GA522/04/0384 Institutional research plan: CEZ:AV0Z40500505 Keywords : aqueous sucrose solutions * subzero temperature * glass transitions Subject RIV: BJ - Thermodynamics Impact factor: 0.809, year: 2007

Use of magnesium-aluminium and zinc-aluminium hydroxycompounds as adsorbents of uranium ions in aqueous solutions

International Nuclear Information System (INIS)

Maki, Toshio

1981-01-01

It was found that precipitates formed by adding NaOH solution to the mixed solutions of MgSO 4 and Al 2 (SO 4 ) 3 with Mg/Al molar ratios of 2 to 4 and to the mixed solution of ZnSO 4 and Al 2 (SO 4 ) 3 with Zn/Al molar ratio of 2, respectively, can be used as efficient adsorbents of [UO 2 (CO 3 ) 3 ] 4- ions in aqueous alkaline carbonate solutions. The ideal structural formulas of the precipitates formed from the mixed Mg-Al solution with Mg/Al ratio of 2.0 and the mixed Zn-Al solution with Zn/Al ratio of 2.0 were estimated to be [Mg 4 Al 2 (OH) 12 ] 2+ [SO 4 .3H 2 O] 2- and [Zn 4 Al 2 (OH) 12 ] 2+ [SO 4 .3H 2 O] 2- , respectively. It has been shown that 0.1 g of the Mg-Al and Zn-Al double hydroxysulphate powders (particle size 70 - 170 μ uptake >97% of the U(VI) ions from 50 ml of an aqueous alkaline carbonate solution containing 100 ppm of U(VI) within 2 h at room temperature. The rates of adsorption of [UO 2 (CO 3 ) 3 ] 4- ions for the Mg-Al and Zn-Al double hydroxysulphate powders were both about 2 times that for the hydrous Ti(IV) oxide powders. Five weight percent sodium bicarbonate solution was found to be effective for the desorption of [UO 2 (CO 3 ) 3 ] 4- ions from the double hydroxysulphate powders. Adsorption capacity of the double hydroxysulphates was discussed in relation to their structure. (author)

Absorption capacity and viscosity for CO_2 capture process using high concentrated PZ-DEAE aqueous solution

International Nuclear Information System (INIS)

Fu, Dong; Wang, LeMeng; Mi, ChenLu; Zhang, Pan

2016-01-01

Highlights: • Absorption of CO_2 in high concentrated DEAE-PZ aqueous solutions were measured. • Viscosities of CO_2-unloaded and CO_2-loaded DEAE-PZ aqueous solutions were measured. • Weiland equation was used to calculate the viscosities. • Effects of temperature, concentration and CO_2 loading on viscosity were demonstrated. - Abstract: The absorption capacity of CO_2 in piperazine (PZ) promoted 2-diethylaminoethanol (DEAE) aqueous solution was measured. The viscosities of both CO_2-unloaded and CO_2-loaded PZ-DEAE aqueous solutions were measured and then modelled. The temperatures ranged from 303.2 K to 323.2 K. The mass fraction of PZ and DEAE respectively ranged from 0 to 0.075 and 0.3 to 0.5. The temperature and concentration dependences of absorption capacity were determined. The effects of temperature, mass fraction and CO_2 loading on viscosities are demonstrated.

Systemic uptake and clearance of chloroform by hairless rats following dermal exposure. I. Brief exposure to aqueous solutions.

Science.gov (United States)

Islam, M S; Zhao, L; Zhou, J; Dong, L; McDougal, J N; Flynn, G L

1996-06-01

The systemic uptake of chloroform from dilute aqueous solutions into live hairless rats under conditions simulating dermal environmental exposure was studied. Whole blood was sampled during a 30-min immersion of an animal within water containing a known concentration of chloroform and then for 5.5 h following its removal from the bath. The amount of chloroform systemically absorbed was determined by comparing the AUCs of the blood concentration vs. time plots from dermal exposure to that obtained after i.v. infusion (for a period of 30 min) of an aqueous solution containing a known amount of chloroform (positive control). Although dermal data implied two-compartment disposition characteristics, i.v. infusion data fit best to a three-compartment disposition. Linear pharmacokinetics was observed both by i.v. administration and percutaneous absorption at the dose levels studied. Chloroform was detected in the rat blood as early as 4 min following exposure. Our findings suggest that about 10.2 mg of chloroform was systemically absorbed after dermal exposure of a rat to an aqueous solution of 0.44 mg/ml. This amount is substantially higher than the predictions of mathematical risk-models put forth by some investigators. However, when expressed as the "effective" permeability coefficient (Kpeff), close agreement was noticed between our value and those estimated by others using physiologically based pharmacokinetic (PBPK) models. Also, in terms of Kpeff, reasonable agreement existed between our and another investigator's past estimates of uptake based on depletion of bath level of chloroform and the actual uptake measured in our current experiments. The estimated onset of systemic entry seen here is entirely consistent with our estimate of how long it takes to establish the diffusion gradient across the stratum corneum based on tape stripping.

Separation of cesium from aqueous solutions using alkylated tetraaryl borates

International Nuclear Information System (INIS)

Feldmaier, F.

1991-01-01

The water solubility of cesium tetraaryl borates was lowered by introducing hydrophobic aliphatic side chains into corresponding acid-resistant fluorosubstituted tetraaryl borates. This improved cesium spearability both in precipitation and in extraction from aqueous solutions. (orig.) [de

(CI 42053) from an aqueous solution using Azadirachta indica leaf

African Journals Online (AJOL)

STORAGESEVER

2008-11-05

Nov 5, 2008 ... ... 42053) from an aqueous solution using Azadirachta indica leaf powder as a low- ... and biodegradable effective adsorbents. They were ob- tained from ... pesticide. The trees are also known as an air purifier. The medicinal.

Recovery of Ionic Liquids from aqueous solution by Nanofiltration

OpenAIRE

Fernández Dámaso, José Francisco

2011-01-01

The T-SAR methodology was combined with membrane characterization methods. An application of the combined approach was demonstrated with two commercial nanofiltration membranes and it was possible to successfully predict their performance for the recovery of ionic liquids from aqueous solution. Using model solutions of Pyr16 (CF3SO2)2N, it could be evidenced the formation of a new phase of ionic liquid during the concentration process. In this case, 66% of the ionic liquid was separated and t...

Kinetic studies of adsorption of Cu (II) from aqueous solution by coriander seeds (Coriandrum Sativum)

Science.gov (United States)

Kadiri, L.; Lebkiri, A.; Rifi, E. H.; Ouass, A.; Essaadaoui, Y.; Lebkiri, I.; Hamad, H.

2018-05-01

The adsorption of copper ions Cu2+ by Coriandrum Sativum seeds (CSS) from aqueous solution was studied in order to highlight the importance of coriander seeds as a potential tool in the treatment of wastewaters containing heavy metals. The kinetic studies of adsorption of Cu (II) were discussed using the spectroscopic technique "Inducting Coupled Plasma" (ICP). The effects of initial copper ion concentration and contact time were determined. All results show that coriander seeds have, over their culinary and medicinal benefits, a significant adsorbent power of copper ions.

Long-term results of treatment with diquafosol ophthalmic solution for aqueous-deficient dry eye.

Science.gov (United States)

Koh, Shizuka; Ikeda, Chikako; Takai, Yoshihiro; Watanabe, Hitoshi; Maeda, Naoyuki; Nishida, Kohji

2013-09-01

To evaluate the preliminary long-term efficacy of diquafosol ophthalmic solution for aqueous-deficient dry eye. Fifteen patients with mild-to-moderate aqueous-deficient dry eye were enrolled. After a washout period, the patients were treated with 3 % diquafosol ophthalmic solution for 6 months. We assessed 12 subjective dry eye symptoms, corneal and conjunctival staining with fluorescein, tear film break-up time (BUT), lower tear meniscus height measured with anterior-segment optical coherence tomography, Schirmer's testing, and adverse reactions at baseline and 1, 3, and 6 months after the start of treatment. Treatment with diquafosol ophthalmic solution significantly improved dry eye symptoms, corneal staining, BUT, and tear meniscus height at 1 month and maintained the effectiveness for 6 months. Conjunctival staining significantly improved 3 and 6 months after treatment. No significant adverse reactions developed. Prolonged use of diquafosol ophthalmic solution for 6 months produced significant improvement both subjectively (dry eye symptom score) and objectively (ocular staining score and tear function tests) for aqueous-deficient dry eye.

Irreversible electron attachment--a key to DNA damage by solvated electrons in aqueous solution.

Science.gov (United States)

Westphal, K; Wiczk, J; Miloch, J; Kciuk, G; Bobrowski, K; Rak, J

2015-11-07

The TYT and TXT trimeric oligonucleotides, where X stands for a native nucleobase, T (thymine), C (cytosine), A (adenine), or G (guanine), and Y indicates a brominated analogue of the former, were irradiated with ionizing radiation generated by a (60)Co source in aqueous solutions containing Tris as a hydroxyl radical scavenger. In the past, these oligomers were bombarded with low energy electrons under an ultra-high vacuum and significant damage to TXT trimers was observed. However, in aqueous solution, hydrated electrons do not produce serious damage to TXT trimers although the employed radiation dose exceeded many times the doses used in radiotherapy. Thus, our studies demonstrate unequivocally that hydrated electrons, which are the major form of electrons generated during radiotherapy, are a negligible factor in damage to native DNA. It was also demonstrated that all the studied brominated nucleobases have a potential to sensitize DNA under hypoxic conditions. Strand breaks, abasic sites and the products of hydroxyl radical attachment to nucleobases have been identified by HPLC and LC-MS methods. Although all the bromonucleobases lead to DNA damage under the experimental conditions of the present work, bromopyrimidines seem to be the radiosensitizers of choice since they lead to more strand breaks than bromopurines.

An Exact Method to Determine the Conductivity of Aqueous Solutions in Acid-Base Titrations

Directory of Open Access Journals (Sweden)

Norma Rodríguez-Laguna

2015-01-01

Full Text Available Several works in the literature show that it is possible to establish the analytic equations to estimate the volume V of a strong base or a strong acid (Vb and Va, resp. being added to a solution of a substance or a mix of substances during an acid-base titration, as well as the equations to estimate the first derivative of the titration plot dpH/dV, and algebraic expressions to determine the buffer β capacity with dilution βdil. This treatment allows establishing the conditions of thermodynamic equilibria for all species within a system containing a mix of species from one or from various polyacid systems. The present work shows that it is possible to determine exactly the electric conductivity of aqueous solutions for these Brønsted acid-base titrations, because the functional relation between this property and the composition of the system in equilibrium is well known; this is achieved using the equivalent conductivity λi values of each of the ions present in a given system. The model employed for the present work confirms the experimental outcomes with the H2SO4, B(OH3, CH3COOH, and H3PO4 aqueous solutions’ titration.

A fluorescent sensor for selective detection of cyanide using mesoporous graphitic carbon(IV) nitride.

Science.gov (United States)

Lee, Eun Zoo; Lee, Sun Uk; Heo, Nam-Su; Stucky, Galen D; Jun, Young-Si; Hong, Won Hi

2012-04-25

A turn-on fluorescence sensor, Cu(2+)-c-mpg-C(3)N(4), was developed for detection of CN(-) in aqueous solution by simply mixing cubic mesoporous graphitic carbon nitride (c-mpg-C(3)N(4)) and aqueous solution of Cu(NO(3))(2). The highly sensitive detection of CN(-) with a detection limit of 80 nM is not only possible in aqueous solution but also in human blood serum.

Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd in Aqueous Solution

Directory of Open Access Journals (Sweden)

Austin Kanayo ASIAGWU

2009-07-01

Full Text Available An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+ in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solution.

ISOCHORIC HEAT CAPACITY OF 1% AQUEOUS SOLUTION OF MAGNESIUM CHLORIDE

Directory of Open Access Journals (Sweden)

V. I. Dvoryanchikov

2016-01-01

Full Text Available Aim. The aim is to conduct an experimental study of isochoric heat capacity of 1% aqueous solution of magnesium chloride along the phase boundary curve.Method. In order to determine the isochoric heat capacity at the phase boundary curve we used the adiabatic calorimeter of KH. I. Amirkhanov.Results. Results of the study of the isochoric heat capacity depending on the temperature are given in tables and figures; the findings are compared with those of other researchers. When evaluating a complex system, we ought not to evaluate its effectiveness on the basis of only one criterion, even a very important, in this case must take into account the requirements of the technical, economic, environmental and of other natures.Conclusions. When solving optimization problems of efficiency in geothermal energy it is necessary to take into account the fact of the temperature dependence of the heat and density. The temperature dependence of the density and heat capacity in the calculations significantly affect the value of the efficiency criterion to be taken into account, otherwise the calculation error can be up to 20%. The data obtained from the isochoric heat capacity of aqueous solutions of magnesium chloride is compared with the data for water and aqueous solutions of NaCl and NaOH, obtained previously, which may be represented as a model of geothermal and sea water.

Removal of fluoride ions from aqueous solution by waste mud

Energy Technology Data Exchange (ETDEWEB)

Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal [Karadeniz Technical University, Faculty of Arts and Sciences, Department of Chemistry, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Chemistry, 38039 Kayseri (Turkey)

2009-09-15

The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

Removal of uranium from aqueous solution by a low cost and high-efficient adsorbent

Energy Technology Data Exchange (ETDEWEB)

Liu, Yun-Hai [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Wang, You-Qun [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Zhang, Zhi-Bin, E-mail: zhangnjut@163.com [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Cao, Xiao-Hong; Nie, Wen-Bin; Li, Qin [Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China); Hua, Rong [State Key Laboratory Breeding Base of Nuclear Resources and Environment (East China Institute of Technology), Ministry of Education, Nanchang, 330013 (China); Key Laboratory of Radioactive Geology and Exploration Technology Fundamental Science for National Defense, East China Institute of Technology, Fuzhou, 344000 (China); Chemistry, Biological and Materials Sciences Department, East China Institute of Technology, Fuzhou, 344000 (China)

2013-05-15

In this study, a low-cost and high-efficient carbonaceous adsorbent (HTC-COOH) with carboxylic groups was developed for U(VI) removal from aqueous solution compared with the pristine hydrothermal carbon (HTC). The structure and chemical properties of resultant adsorbents were characterized by Scanning electron microscope (SEM), N{sub 2} adsorption–desorption, Fourier transform-infrared spectra (FT-IR) and acid–base titration. The key factors (solution pH, contact time, initial U(VI) concentrations and temperature) affected the adsorption of U(VI) on adsorbents were investigated using batch experiments. The adsorption of U(VI) on HTC and HTC-COOH was pH-dependent, and increased with temperature and initial ion concentration. The adsorption equilibrium of U(VI) on adsorbents was well defined by the Langmuir isothermal equation, and the monolayer adsorption capacity of HTC-COOH was found to be 205.8 mg/g. The kinetics of adsorption was very in accordance with the pseudo-second-order rate model. The adsorption processes of U(VI) on HTC and HTC-COOH were endothermic and spontaneous in nature according to the thermodynamics of adsorption. Furthermore, HTC-COOH could selectively adsorption of U(VI) in aqueous solution containing co-existing ions (Mg{sup 2+}, Co{sup 2+}, Ni{sup 2+}, Zn{sup 2+} and Mn{sup 2+}). From the results of the experiments, it is found that the HTC-COOH is a potential adsorbent for effective removal of U(VI) from polluted water.

Removal of uranium from aqueous solution by a low cost and high-efficient adsorbent

Science.gov (United States)

Liu, Yun-Hai; Wang, You-Qun; Zhang, Zhi-Bin; Cao, Xiao-Hong; Nie, Wen-Bin; Li, Qin; Hua, Rong

2013-05-01

In this study, a low-cost and high-efficient carbonaceous adsorbent (HTC-COOH) with carboxylic groups was developed for U(VI) removal from aqueous solution compared with the pristine hydrothermal carbon (HTC). The structure and chemical properties of resultant adsorbents were characterized by Scanning electron microscope (SEM), N2 adsorption-desorption, Fourier transform-infrared spectra (FT-IR) and acid-base titration. The key factors (solution pH, contact time, initial U(VI) concentrations and temperature) affected the adsorption of U(VI) on adsorbents were investigated using batch experiments. The adsorption of U(VI) on HTC and HTC-COOH was pH-dependent, and increased with temperature and initial ion concentration. The adsorption equilibrium of U(VI) on adsorbents was well defined by the Langmuir isothermal equation, and the monolayer adsorption capacity of HTC-COOH was found to be 205.8 mg/g. The kinetics of adsorption was very in accordance with the pseudo-second-order rate model. The adsorption processes of U(VI) on HTC and HTC-COOH were endothermic and spontaneous in nature according to the thermodynamics of adsorption. Furthermore, HTC-COOH could selectively adsorption of U(VI) in aqueous solution containing co-existing ions (Mg2+, Co2+, Ni2+, Zn2+ and Mn2+). From the results of the experiments, it is found that the HTC-COOH is a potential adsorbent for effective removal of U(VI) from polluted water.

Preferential adsorption of uranium ions in aqueous solutions by polymers

International Nuclear Information System (INIS)

Sakuragi, Masako; Ichimura, Kunihiro; Fujishige, Shoei; Kato, Masao

1981-01-01

Amidoxime fiber and triazine fiber were prepared by chemical modification of commercially available polyacrylonitril fiber. It was found that the Amidoxime fiber is efficient to adsorb uranium ions in the artificial sea water. The efficiency of the preferential adsorption decreases by treatment the material with an acid-or an alkaline-solution. The triazine fiber adsorbs uranium ions only in aqueous solutions of such uranyl acetate, in the absence of other ions. In the artificial sea water, it adsorbs other ions instead of uranium. The preferential adsorption of uranium ions was further investigated with a series of polystyrenesulfonamides. Among the polystyrene derivatives, those having carboxyl groups, derived from imino diacetic acid (PSt-Imi), β-alanine (PSt-Ala), glycine (PSt-Gly), and sarcosine (PSt-Sar) were qualified for further discussion. However, it was found that the amount of adsorption of uranium ions by PSt-Imi decreases with increasing the volume of the artificial sea water and/or the duration of the treatment. Taking into account the facts, the preferential adsorption of uranium ions by PSt-Imi in aqueous solution was discussed in detail. (author)

Removal of Cholera Toxin from Aqueous Solution by Probiotic Bacteria

Directory of Open Access Journals (Sweden)

Jussi A. O. Meriluoto

2012-06-01

Full Text Available Cholera remains a serious health problem, especially in developing countries where basic hygiene standards are not met. The symptoms of cholera are caused by cholera toxin, an enterotoxin, which is produced by the bacterium Vibrio cholerae. We have recently shown that human probiotic bacteria are capable of removing cyanobacterial toxins from aqueous solutions. In the present study we investigate the ability of the human probiotic bacteria, Lactobacillus rhamnosus strain GG (ATCC 53103 and Bifidobacterium longum 46 (DSM 14583, to remove cholera toxin from solution in vitro. Lactobacillus rhamnosus strain GG and Bifidobacterium longum 46 were able to remove 68% and 59% of cholera toxin from aqueous solutions during 18 h of incubation at 37 °C, respectively. The effect was dependent on bacterial concentration and L. rhamnosus GG was more effective at lower bacterial concentrations. No significant effect on cholera toxin concentration was observed when nonviable bacteria or bacterial supernatant was used.

Comparison Study On Sunlight Or Gamma Radiation Aging Resistance Of Poly (Vinyl Pyrrolidone) Aqueous Solution With PVP Nanogel

International Nuclear Information System (INIS)

Doan Binh; Pham Thu Hong; Nguyen Nguyet Dieu; Nguyen Thanh Duoc

2011-01-01

Comparison study on sunlight or gamma-radiation aging resistance of poly (vinyl pyrrolidone) (PVP) aqueous solution with PVP nanogel at 0.5% was carried out. Sunlight or gamma- radiation aging resistance of PVP aqueous solution and nanogel was evaluated on the basis of their intrinsic viscosity, UV-VIS absorbance, weight averaged molecular weight (M w ). The PVP aqueous solution and nanogel exposed to sunlight in the storage duration of 3 months and to gamma radiation at absorbed doses of 0, 15, 30, 50 kGy were used for this study. Furthermore, the stability of PVP nanogel and of PVP aqueous solution was also studied on the change of their intrinsic viscosity, UV-VIS absorbance, weight averaged molecular weight, particle size distribution and coil size. The experimental results were shown that the aging resistance of PVP nanogel was higher than that of PVP aqueous solution when exposed to gamma radiation or sunlight. (author)

from an aqueous solution using Azadirachta indica leaf powder

African Journals Online (AJOL)

Azadirachta indica (neem) leaf powder was used as an adsorbent for the removal of textile dye from aqueous solution. The adsorption of dye on A. indica was found to be dependent on contact time, dye concentration and amount of adsorbent. Spectrophotometric technique was used for the measurement of concentration of ...

Iodine capture by Hofmann-type clathrate Ni(II)(pz)[Ni(II)(CN)_4

International Nuclear Information System (INIS)

Massasso, Giovanni; Long, Jerome; Haines, Julien; Devautour-Vinot, Sabine; Maurin, Guillaume; Larionova, Joulia; Guerin, Christian; Guari, Yannick; Grandjean, Agnes; Onida, Barbara; Donnadieu, Bruno

2014-01-01

The thermally stable Hofmann-type clathrate framework Ni(II)(pz)[Ni(II)(CN)_4] (pz = pyrazine) was investigated for the efficient and reversible sorption of iodine (I_2) in the gaseous phase and in solution with a maximum adsorption capacity of 1 mol of I_2 per 1 mol of Ni(II)pz)[Ni(II)(CN)_4] in solution. (authors)

Absorption of carbon dioxide in aqueous solutions of imidazolium ionic liquids with carboxylate anions

International Nuclear Information System (INIS)

Baj, Stefan; Krawczyk, Tomasz; Dabrowska, Aleksandra; Siewniak, Agnieszka; Sobolewski, Aleksander

2015-01-01

The solubility of carbon dioxide at atmospheric pressure in aqueous mixtures of 1,3-alkyl substituted imidazolium ionic liquids (ILs) containing carboxylic anions was studied. The ILs showed increased solubility of CO 2 with decreasing water concentration. The relationship between the CO 2 concentration in solution and the mole fraction of water in the ILs describes a sigmoidal curve. The regression constants of a logistic function were used to quantitatively assess the absorbent capacity and the effect of water on CO 2 absorption. ILs containing the most basic anions, such as pivalate, propionate and acetate, had the best properties. It was observed that the impact of water on absorption primarily depended on the cation structure. The best absorption performance was observed for 1,3-dibutylimidazolium pivalate and 1-butyl-3-methyl imidazolium acetate.

Adsorption of tannic acid from aqueous solution onto surfactant-modified zeolite

Energy Technology Data Exchange (ETDEWEB)

Lin, Jianwei, E-mail: jwlin@shou.edu.cn [College of Marine Science, Shanghai Ocean University, No. 999 Hucheng Huan Road, Pudong District, Shanghai 201306 (China); Zhan, Yanhui; Zhu, Zhiliang [State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Xing, Yunqing [College of Marine Science, Shanghai Ocean University, No. 999 Hucheng Huan Road, Pudong District, Shanghai 201306 (China)

2011-10-15

Graphical abstract: Surfactant-modified zeolites (SMZs) with various loadings of cetylpyridinium bromide (CPB) were used as adsorbents to remove tannic acid (TA) from aqueous solution. Highlights: {yields} Surfactant modified zeolites (SMZs) have a good tannic acid (TA) adsorption capacity. {yields} Adsorption capacity for SMZ with bilayer was relatively high at solution pH 3.5-7.0. {yields} Adsorption was well described by pseudo-second-order kinetic model. {yields} Adsorption fitted well with Langmuir, Redlich-Peterson and Sips isotherm models. {yields} Coexisting Cu(II) in aqueous solution resulted in markedly enhanced TA adsorption. - Abstract: Surfactant-modified zeolites (SMZs) with various loadings of cetylpyridinium bromide (CPB) were used as adsorbents to remove tannic acid (TA) from aqueous solution. The TA adsorption efficiencies for natural zeolite and various SMZs were compared. SMZ presented higher TA adsorption efficiency than natural zeolite, and SMZ with higher loading amount of CPB exhibited higher TA adsorption efficiency. The adsorption of TA onto SMZ as a function of contact time, initial adsorbate concentration, temperature, ionic strength, coexisting Cu(II) and solution pH was investigated. The adsorbents before and after adsorption were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), thermogravimetric analysis (TGA), and Fourier transform infrared (FT-IR) spectroscopy. The adsorption kinetics of TA onto SMZ with CPB bilayer coverage (SMZ-CBC) followed a pseudo-second-order model. The equilibrium adsorption data of TA onto SMZ-CBC were well represented by Langmuir, Redlich-Peterson and Sips isotherm models. The calculated thermodynamic parameters indicated that TA adsorption onto SMZ-CBC was spontaneous and exothermic. The TA adsorption capacity for SMZ-CBC slightly decreased with increasing ionic strength but significantly increased with increasing Cu(II) concentration. The TA adsorption

Rapid synthesis of CdSe nanocrystals in aqueous solution at room ...

Indian Academy of Sciences (India)

Administrator

Water-soluble thioglycolic acid-capped CdSe nanocrystals (NCs) were prepared in aqueous solu- tion at room temperature. We investigated the ... NCs dispersed in buffer solution (pH = 4⋅0). FTIR spectra were recorded on a ... the theory of acid-base equilibrium, the initial pH value of original solution determines the ...

Characteristics of regenerated nanocellulosic fibers from cellulose dissolution in aqueous solutions for wood fiber/polypropylene composites

Science.gov (United States)

Sangyeob Lee; Hui Pan; Chung Y. Hse; Alfred R. Gunasekaran; Todd F. Shupe

2014-01-01

The effects of aqueous solutions were evaluated on the properties of regenerated cellulosic nanofibers prepared from pure cellulose fibers in various formulations of aqueous solutions. Thermoplastic composites were prepared with reinforcement of the regenerated cellulosic nanofibers. The regenerated cellulosic fibers from cellulosic woody biomass were obtained from...

Gamma-radiolysis of aqueous solutions of methyl orange and chrysoidine

International Nuclear Information System (INIS)

Khabarov, V.N.; Kozlov, L.L.; Panchenkov, G.M.

1980-01-01

Radiation-chemical bleaching of azo dyes of methyl orange and chrysoidine in aqueous and aqueous-alcoholic solutions under the effect of γ-radiation of 60 Co is studied. The effect of different additions and pH value of medium upon radiolysis of azo dyes is investigated. Radiation-chemical yields of the bleaching are determined. Quantitative connection between the initial yields of water radiolysis products and radiation yields of the bleaching of azo dyes is established. On the basis of the results obtained the most probable mechanism of methyl orange and chrysoidine bleaching is suggested

Electrochemical reactions of uranyl(VI) complexes in aqueous solution, non-aqueous solvents, and ionic liquids

International Nuclear Information System (INIS)

Ikeda, Yasuhisa

2006-01-01

Author's recent experimental results on the chemistry of U(V) in aqueous solution, non-aqueous solvents, and ionic solvents by cyclic voltametry are described. The U(V) was produced by electrochemical reduction of uranyl U(VI) ions or complexes such as carbonates, DMF(N, N-dimethylformamide), DMSO(dimethylsulfoxide), acetylacetonato, and other organic polydental ligands. The produced U(V) complexes were studied by spectrophotometry using optical-transmission thin-layer electrode. The U(V) complexes in non-aqueous solvents were found to be rather stable, they undergo ligand-dissociation reaction but not disproportionation reaction. The structure and electronic spectra as well as IR spectra of the complexes were studied. The present method was further developed to study the behavior of U(V) complexes in ionic liquids as molten salts, e.g., alkaline metals chlorides. Thus, the present research contributes to understanding the chemistry of 5fl system. Application to such nuclear technology as spent fuel reprocessing is discussed. (S. Ohno)

Examination of rheological properties of aqueous solutions of sodium caseinate

OpenAIRE

Jolanta Gawałek; Piotr Wesołowski

2012-01-01

Application of sodium caseinate as a functional additive in manufacturing processes requires production of its concentrated aqueous solutions which, in industrial conditions, presents a number of difficulties. In order to develop an effective and optimal industrial process of mixing – manufacturing a concentrated solution of sodium caseinate, it is essential to know rheological properties in a definite range of concentrations changing in the course of the dissolving process. The materia...

The salting-out effect and phase separation in aqueous solutions of tri-sodium citrate and 1-butyl-3-methylimidazolium bromide

International Nuclear Information System (INIS)

Sadeghi, Rahmat; Golabiazar, Roonak; Shekaari, Hemayat

2010-01-01

The aim of this work is to obtain further evidence about the salting-out effect produced by the addition of tri-sodium citrate to aqueous solutions of water miscible ionic liquid 1-butyl-3-methylimidazolium bromide ([C 4 mim][Br]) by evaluating the effect of tri-sodium citrate on the thermodynamic properties of aqueous solutions of this ionic liquid. Experimental measurements of density and sound velocity at different temperatures ranging from (288.15 to 308.15) K, the refractive index at 308.15 K and the liquid-liquid phase diagram at different temperatures ranging from (288.15 to 338.15) K for aqueous solutions containing 1-butyl-3-methylimidazolium bromide ([C 4 mim][Br]) and tri-sodium citrate (Na 3 Cit) are taken. The apparent molar volume of transfer of [C 4 mim][Br] from water to aqueous solutions of Na 3 Cit have positive values and it increases by increasing salt molality. Although at high IL molality, the apparent molar isentropic compressibility shows similar behaviour with that of the apparent molar volume. However at low concentrations of IL, the apparent molar isentropic compressibility of transfer of [C 4 mim][Br] from water to aqueous solutions of Na 3 Cit have negative values. The effects of temperature and the addition of Na 3 Cit and [C 4 mim][Br] on the liquid-liquid phase diagram of the investigated system have been studied. It was found that an increase in temperature caused the expansion of the one-phase region. The presence of Na 3 Cit triggers a salting-out effect, leading to significant upward shifts of the liquid-liquid de-mixing temperatures of the system. The effect of temperature on the phase-forming ability in the system investigated has been studied based on a salting-out coefficient obtained from fitting the binodal values to a Setschenow-type equation for each temperature. Based on cloud point values, the energetics of the clouding process have been estimated and it was found that both of entropy and enthalpy are the driving forces

WHATIF-AQ, Geochem Speciation and Saturation of Aqueous Solution

International Nuclear Information System (INIS)

Nielsen, Ole John; Jensen, Bror Skytte

1988-01-01

1 - Description of program or function: WHATIF-AQ is part of a family of programs for calculations of geochemistry in the near-field of radioactive waste with temperature gradients. The program calculates speciation and saturation indices for an aqueous solution at temperatures in the range 0 - 125 degrees C. The chemical equilibrium is determined by solving a set of nonlinear equations consisting of the equilibrium constant and mass balance constraints. 2 - Method of solution: The set of equations is solved using a generalized Newton-Raphson technique

Comparative analysis of the effect of pretreating aspen wood with aqueous and aqueous-organic solutions of sulfuric and nitric acid on its reactivity during enzymatic hydrolysis

DEFF Research Database (Denmark)

Dotsenko, Gleb; Osipov, D. O.; Zorov, I. N.

2016-01-01

The effect of aspen wood pretreatment methods with the use of both aqueous solutions of sulfuric and nitric acids and aqueous-organic solutions (ethanol, butanol) of sulfuric acid (organosolv) on the limiting degree of conversion of this type of raw material into simple sugars during enzymatic...

Densities and solubilities of Glycylglycine and Glycyl-L-Alanine in Aqueous Electrolyte Solutions

DEFF Research Database (Denmark)

Breil, Martin Peter; Mollerup, Jørgen; Rudolph, E. Susanne J.

2004-01-01

Solubilities of glycylglycine and glycyl-L-alanine in aqueous electrolyte solutions containing 0-6 molal NaCl, 0-1 molal Na2SO4, and 0-1 molal (NH4)(2)SO4, have been determined experimentally at 298.15 K and atmospheric pressure. The solubility of glycylglycine and glycyl-L-alanine in pure water...... is 1.74 and 4.78 mol/kg of water, respectively. The solubility of glycylglycine in salt solutions of NaCl, Na2SO4, and (NH4)(2)SO4 show a moderate salting-in effect. The solubility of glycyl-L-alanine show a minor or no salting-in effect at low salt concentrations and a moderate salting-out effect...... at higher salt concentrations in NaCl and Na2SO4, and in (NH4)(2)SO4 the solubility is almost constant. The densities of the solutions have been determined experimentally, and the volume expansions by dissolving salt and dipeptide in water have been calculated. (C) 2003 Elsevier B.V. All rights reserved....

Artifactual degradation of secondary amine-containing drugs during accelerated stability testing when saturated sodium nitrite solutions are used for humidity control.

Science.gov (United States)

Sluggett, Gregory W; Zelesky, Todd; Hetrick, Evan M; Babayan, Yelizaveta; Baertschi, Steven W

2018-02-05

Accelerated stability studies of pharmaceutical products are commonly conducted at various combinations of temperature and relative humidity (RH). The RH of the sample environment can be controlled to set points using humidity-controlled stability chambers or via storage of the sample in a closed container in the presence of a saturated aqueous salt solution. Herein we report an unexpected N-nitrosation reaction that occurs upon storage of carvedilol- or propranolol-excipient blends in a stability chamber in the presence of saturated sodium nitrite (NaNO 2 ) solution to control relative humidity (∼60% RH). In both cases, the major products were identified as the corresponding N-nitroso derivatives of the secondary amine drugs based on mass spectrometry, UV-vis and retention time. These degradation products were not observed upon storage of the samples at the same temperature and humidity but in the presence of saturated potassium iodide (KI) solution (∼60% RH) for humidity control. The levels of the N-nitrosamine derivatives varied with the pH of various NaNO 2 batches. The presence of volatile NOx species in the headspace of a container containing saturated NaNO 2 solution was confirmed via the Griess assay. The process for formation of the N-nitrosamine derivatives is proposed to involve volatilization of nitric oxide (NO) from aqueous nitrite solution into the headspace of the container followed by diffusion into the solid drug-excipient blend and subsequent reaction of NOx with the secondary amine. Copyright © 2017 Elsevier B.V. All rights reserved.

Biosorption of mercury from aqueous solutions using highly characterised peats

Directory of Open Access Journals (Sweden)

A.M. Rizzuti

2015-02-01

Full Text Available This research investigated the biosorption of mercury from aqueous solutions by six highly characterised peats. Samples of the peats were tested both in unaltered condition and after being treated with hydrochloric acid (HCl to free up any occupied exchange sites. Other variables tested were sample dose, contact time, mixing temperature, and the concentration and pH of the mercury solution. Desorption studies were also performed, and tests were done to determine whether the peats could be re-used for mercury biosorption. The results indicate that all six peat types biosorb mercury from aqueous solutions extremely well (92−100 % removal and that their mercury removal capacities are not significantly affected by manipulation of the various factors tested. The factor that had the greatest impact on the mercury removal capacities of the peats was the pH of the mercury solution. The optimal mercury solution pH for mercury removal was in the range 5−7 for four of the peats and in the range 2−3 for the other two. The desorption results indicate that it may be possible to recover up to 41 % of the removed mercury. All of the peat types tested can be repeatedly re-used for additional mercury biosorption cycles. Hence, their disposal should not become a hazardous waste problem.

Pulse radiolysis of pyridine and methylpyridines in aqueous solutions

DEFF Research Database (Denmark)

Solar, S.; Getoff, N.; Sehested, K.

1993-01-01

The radicals formed from pyridine, 3-methylpyridine, 3,5-dimethylpyridine, 2,6-dimethylpyridine and 2,4,6-trimethylpyridine by attack of H, e(aq)-, OH and O.- in aqueous solutions were investigated by pulse radiolysis in the pH-range 1-13.8. The UV-vis. absorption spectra as well as the formation...

Accurate Description of Calcium Solvation in Concentrated Aqueous Solutions

Czech Academy of Sciences Publication Activity Database

Kohagen, Miriam; Mason, Philip E.; Jungwirth, Pavel

2014-01-01

Roč. 118, č. 28 (2014), s. 7902-7909 ISSN 1520-6106 R&D Projects: GA ČR GBP208/12/G016; GA MŠk LH12001 Institutional support: RVO:61388963 Keywords : calcium chloride * aqueous solution * molecular dynamics * neutron scattering Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.302, year: 2014

Chemically induced dynamic electron polarization. Pulse radiolysis of aqueous solutions of alcohols

International Nuclear Information System (INIS)

Trifunac, A.D.; Thurnauer, M.C.

1975-01-01

The radical pair model of chemically induced dynamic electron polarization (CIDEP) is experimentally verified. Aqueous solutions of alcohols were irradiated with 3 MeV electrons and observed with time resolved electron paramagnetic resonance (EPR) spectroscopy. Relative line intensities of the polarized EPR spectra of radicals from methanol and especially ethylene glycol, alone and in the presence of radicals from compounds containing halogens, illustrates the polarization dependence on the g-factor differences between the radical pair components. The observation of the relative polarization enhancement in the various lines of the multiline EPR spectra illustrates the polarization dependence on the hyperfine terms. Intrinsic enhancements are calculated and are shown to be proportional to the observed enhancement, showing that the radical pair model of CIDEP is qualitatively correct

Simultaneous determination of nitric acid and uranium concentrations in aqueous solution from measurements of electrical conductivity, density, and temperature

International Nuclear Information System (INIS)

Spencer, B.B.

1991-01-01

Nuclear fuel reprocessing plants handle aqueous solutions of nitric acid and uranium in large quantities. Automatic control of process operations requires reliable measurements of these solutes concentration, but this is difficult to directly measure. Physical properties such as solution density and electrical conductivity vary with solute concentration and temperature. Conductivity, density and temperature can be measured accurately with relatively simple and inexpensive devices. These properties can be used to determine solute concentrations will good correlations. This paper provides the appropriate correlations for solutions containing 2 to 6 Molar (M) nitric acid and 0 to 300 g/L uranium metal at temperatures from 25--90 degrees C. The equations are most accurate below 5 M nitric acid, due to a broad maximum in the conductivity curve at 6 M. 12 refs., 9 figs., 6 tabs

Photogeneration of H2O2 in SPEEK/PVA aqueous polymer solutions.

Science.gov (United States)

Little, Brian K; Lockhart, PaviElle; Slaten, B L; Mills, G

2013-05-23

Photolysis of air-saturated aqueous solutions containing sulphonated poly(ether etherketone) and poly(vinyl alcohol) results in the generation of hydrogen peroxide. Consumption of oxygen and H2O2 formation are initially concurrent processes with a quantum yield of peroxide generation of 0.02 in stirred or unstirred solutions within the range of 7 ≤ pH ≤ 9. The results are rationalized in terms of O2 reduction by photogenerated α-hydroxy radicals of the polymeric ketone in competition with radical-radical processes that consume the macromolecular reducing agents. Generation of H2O2 is controlled by the photochemical transformation that produces the polymer radicals, which is most efficient in neutral and slightly alkaline solutions. Quenching of the excited state of the polyketone by both H3O(+) and OH(-) affect the yields of the reducing macromolecular radicals and of H2O2. Deprotonation of the α-hydroxy polymeric radicals at pH > 9 accelerate their decay and contribute to suppressing the peroxide yields in basic solutions. Maxima in [H2O2] are observed when illuminations are performed with static systems, where O2 reduction is faster than diffusion of oxygen into the solutions. Under such conditions H2O2 can compete with O2 for the reducing radicals resulting in a consumption of the peroxide.

Cytosine modifications after gamma irradiation in aerated aqueous solution of Escherichia coli DNA

International Nuclear Information System (INIS)

Polverelli, M.

1983-04-01

After gamma irradiation of cytosine in aerated aqueous solution and utilization of various spectrometric methods (mass spectrometry, proton nuclear magnetic resonance and infrared spectrometry) about ten new radiolysis products were identified. The formation of N-glycolylbiuret in H 2 18 O aqueous solution of irradiated cytosine at pH 4,5 indicated that the preferred 18 OH hydroxyl radical attack was at C-5. The formation of trans 1-carbamoyl-4,5 dihydroxyimidazolidin-2 oxo which is the major product after cytosine pyrimidine ring rearrangement took place preferentially at neutral pH, while N-glycolylbiuret predominated at pH 4,5. The deamination pathway was predominant when cytosine was irradiated at acidic pH values (pH 2 ) or in copper complexes. The development of a new acid hydrolysis method using fluorhydric acid stabilized in pyridine made easier the evaluation of cytosine modifications after gamma irradiation in aerated aqueous solution of E. Coli DNA- 14 C-2 cytosine. This hydrolytic agent removed the modified bases from the polynucleotidic chain. A difference was found between the proportion of radiolytic products removed by acid hydrolysis and by irradiation of the free base in solution [fr

Comparison of cytotoxicity in vitro and irritation in vivo for aqueous and oily solutions of surfactants.

Science.gov (United States)

Czajkowska-Kośnik, Anna; Wolska, Eliza; Chorążewicz, Juliusz; Sznitowska, Małgorzata

2015-01-01

The in vivo model on rabbit eyes and the in vitro cytotoxicity on fibroblasts were used to compare irritation effect of aqueous and oily (Miglyol 812) solutions of surfactants. Tween 20, Tween 80 and Cremophor EL were tested in different concentrations (0.1, 1 or 5%) and the in vitro test demonstrated that surfactants in oil are less cytotoxic than in aqueous solutions. In the in vivo study, the aqueous solutions of surfactants were characterized as non-irritant while small changes in conjunctiva were observed after application the oily solutions of surfactants and the preparations were classified as slightly irritant, however this effect was similar when Miglyol was applied alone. In conclusion, it is reported that the MTT assay does not correlate well with the Draize scores.

An example of transition from a corrosion process in gaseous phase to corrosion in aqueous environment: the case of Z2CN18-10 stainless steel by iodine and water in vapour phase

International Nuclear Information System (INIS)

Mathieu, Bruno

1990-01-01

This research thesis addresses an example of transition of a corrosion process in gaseous phase towards corrosion in aqueous environment, specifically in the case of the corrosion of the Z2CN18-10 stainless steel by gaseous iodine in presence of water vapour (and possibly nitrogen dioxide). This transition occurs in two steps: initiation in gaseous phase and growth in aqueous environment. This transition is due to hygroscopic properties of mostly chromium iodides and, to a lesser extent, iron iodides. Morphological, electrochemical and thermogravimetry studies have been performed by varying different parameters governing corrosion processes: corrosion temperature, iodine concentration, relative humidity, and reaction time [fr

Characterization of aqueous solution of cresol red as food irradiation dosimeter

Energy Technology Data Exchange (ETDEWEB)

Khan, H M; Tabassum, S; Wahid, M S [Peshawar University, Peshawar (Pakistan). Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry

2009-06-15

Dilute aqueous solution of cresol red has been evaluated spectrophotometrically as possible gamma rays dosimeter. A 0.10 mM solution of cresol red was irradiated by gamma rays using a cobalt-60 radiation source. The absorbance spectra of the unirradiated and irradiated solutions were recorded using double beam scanning spectrophotometer. The absorbance of the solution before and after irradiation was measured at 434 nm ({lambda}{sub max}) as well as at other wavelengths (415, 448 and 470 nm). Various parameters, such as Absorbance (A), {delta}A, %A, -log A and log A{sub o}/A{sub i} were plotted against radiation dose, in order to check the response of cresol red solution and its possible use as chemical dosimeter. The response plots of A, {delta}A, and %A versus absorbed dose showed that the solution can be used as a radiation dosimeter in a dose range up to 0.82 kGy. Using response plots of -log A and log A{sub o}/A{sub i}, the useful dose range can be extended up to 1.65 kGy; which are useful dose ranges for food irradiation applications. Stability studies of cresol red solution at different light and temperature conditions for pre- and post-irradiated storage of the dosimetric solutions suggested that aqueous solution of cresol red is highly stable in dark, under fluorescence light and at room temperature up to 150 days (author)

Removal of cadmium from aqueous solution using marine green algae, Ulva lactuca

Directory of Open Access Journals (Sweden)

Mohamed M. Ghoneim

2014-01-01

Full Text Available The present study aimed to evaluate the efficiency of marine algae for removal of metals from the aqueous solution. The green alga, Ulva lactuca, collected from the intertidal zone of the Suez Bay, northern part of the Red Sea was used to reduce cadmium levels from the aqueous solutions. The biosorption mechanisms of Cd2+ ions onto the algal tissues were examined using various analytical techniques: Fourier-transform infrared spectroscopy (FT-IR and Scanning electron microscopy (SEM. Results indicated that at the optimum pH value of 5.5; about 0.1 g of U. lactuca was enough to remove 99.2% of 10 mg L−1 Cd2+ at 30 °C in the aqueous solutions. The equilibrium data were well fitted with the Langmuir and Freundlich isotherms. The monolayer adsorption capacity was 29.1 mg g−1. The calculated RL and ‘n’ values have proved the favorability of cadmium adsorption onto U. lactuca. The desorption test revealed that HCl was the best for the elution of metals from the tested alga. In conclusion, the seaweed U. lactuca was the favorable alternative of cadmium removal from water.

The blue complexes of U in aqueous solutions

International Nuclear Information System (INIS)

Musikas, C.

1976-01-01

Mixed-valence uranium complexes were synthesized. Hydrolysis of hexavalent U leads to anionic species soluble in aqueous solutions when the UO 2 ++ ions are neutralized by tetraalkylammonium hydroxides. These complexes are polynuclear and the size and interatomic distances found for the polyanions are those of macromolecules. By hydrazine of these complexes, solutions were obtained and their absorption spectra studied. The spectra of U(VI) and U(V) ions are observed, together with new bands attributable to a charge transfer. It may be concluded that the blue complexes of uranium are type II composite-valence complexes for which the delocalization coefficient α can be calculated [fr

Quantitative Method for the Detection of Triethyl Phosphate in Aqueous Solutions

National Research Council Canada - National Science Library

Bagalawis, Rosa

2003-01-01

...) at the parts per million level in aqueous solution. TEP was used as a chemical agent simulant to evaluate the penetration characteristics of clothing, gloves, boots and items of personal equipment...

SODIUM DI-N-DODECYL PHOSPHATE VESICLES IN AQUEOUS-SOLUTION - EFFECTS OF ETHANOL, PROPANOL, AND TETRAHYDROFURAN ON THE GEL TO LIQUID-PHASE TRANSITION

NARCIS (Netherlands)

BLANDAMER, MJ; BRIGGS, B; BUTT, MD; WATERS, M; CULLIS, PM; ENGBERTS, JBFN; HOEKSTRA, D; MOHANTY, RK

1994-01-01

For aqueous solutions containing vesicles formed by sodium di-n-dodecyl phosphate, the gel to liquid-crystal transition occurs near 35 degrees C, the temperature T-m. When ethanol is added, T-m decreases, but the scan shows evidence of several transitions as more alcohol is added. The effect of

The kinetics of dye formation by pulse radiolysis of pararosaniline cyanide in aqueous or organic solution

International Nuclear Information System (INIS)

McLaughlin, W.L.; Holcman, J.; Sehested, K.; Kosanic, M.M.

1979-11-01

The radiation-induced conversion of the leucocyanide of pararosaniline dye to the highly colored salt-isomer of the dye in acidic aqueous solution (wavelength of maximum absorption lambda sub(max)=540 nm) or polar organic solution (lambda sub(max)=550 nm), takes place in two separate processes. The first is very fast (within 3 s -1 to 10 6 s -1 , as the acidity or concentration of an oxidizing agent increases. In oxygen-free acidic aqueous or organic solutions (argon saturated) there is an unstable transient species (lambdasub(max)=380 nm). When using O 2 or N 2 O-saturated aqueous or organic solution, there is no intermediate absorption band at 380 nm, but the slow process of dye formation at 540 or 550 nm is still sequential to the initial fast process having somewhat faster kinetics than in Ar-saturated solution. (author)

A study on the localized corrosion of cobalt in bicarbonate solutions containing halide ions

Energy Technology Data Exchange (ETDEWEB)

Gallant, Danick [Departement de Biologie, Chimie et Sciences de la Sante, Universite du Quebec a Rimouski, 300, Allee des Ursulines, Rimouski, Que., G5L 3A1 (Canada); Departement de Chimie, Universite Laval, Quebec, Que., G1K 7P4 (Canada); Simard, Stephan [Departement de Biologie, Chimie et Sciences de la Sante, Universite du Quebec a Rimouski, 300, Allee des Ursulines, Rimouski, Que., G5L 3A1 (Canada)]. E-mail: stephan_simard@uqar.qc.ca

2005-07-01

The localized attack of cobalt in bicarbonate aqueous solutions containing halide ions was investigated using electrochemical techniques, scanning electron microscopy, UV-visible and Raman spectroscopies. Rotating disc and rotating ring-disc electrodes were used to determine the effect of bicarbonate concentration, solution pH, nature and concentration of the halide ions, convection and potential sweep rate on the corrosion processes. These parameters were found to play a key role on the localized attack induced by halide ions by influencing the production of a Co(HCO{sub 3}){sub 2} precipitate on the pit surface. Potentiostatically generated cobalt oxide films (CoO and Co{sub 3}O{sub 4}) were found to be efficient to reduce pitting corrosion of cobalt.

Removal of lead from aqueous solution on glutamate intercalated layered double hydroxide

Directory of Open Access Journals (Sweden)

Shen Yanming

2017-05-01

Full Text Available Glutamate intercalated Mg–Al layered double hydroxide (LDH was prepared by co-precipitation and the removal of Pb2+ in the aqueous solution was investigated. The prepared samples were characterized by XRD, FT-IR and SEM. It was shown that glutamate can intercalate into the interlayer space of Mg–Al LDH. The glutamate intercalated Mg–Al LDH can effectively adsorb Pb2+ in the aqueous solution with an adsorption capacity of 68.49 mg g−1. The adsorption of Pb2+ on glutamate intercalated Mg–Al LDH fitted the pseudo-second-order kinetics model and the isotherm can be well defined by Langmuir model.

Evaluation of biosurfactants grown in corn oil by Rhodococcus rhodochrous on removing of heavy metal ion from aqueous solution

International Nuclear Information System (INIS)

Suryanti, Venty; Hastuti, Sri; Pujiastuti, Dwi

2016-01-01

The potential application of biosurfactants to remove heavy metal ion from aqueous solution by batch technique was examined. The glycolipids type biosurfactants were grown in a media containing of 20% v/v corn oil with 7 days of fermentation by Rhodococcus rhodochrous. The biosurfactants reduced the surface tension of water of about 51% from 62 mN/m to 30 mN/m. The biosurfactant increased the E24 of water-palm oil emulsion of about 55% from 43% to 97% and could maintain this E24 value of above 50% for up to 9 days. Heavy metal ion removal, in this case cadmium ion, by crude and patially purified biosurfactants has been investigated from aqueous solution at pH 6. Adsorption capacity of Cd(II) ion by crude biosurfactant with 5 and 10 minutes of contact times were 1.74 and 1.82 mg/g, respectively. Additionally, the adsorption capacity of Cd(II) ion by partially purified biosurfactant with 5 and 10 minutes of contact times were 0.79 and 1.34 mg/g, respectively. The results demonstrated that the adsorption capacity of Cd(II) ion by crude biosurfactant was higher than that of by partially purified biosurfactant. The results suggested that the biosurfactant could be used in the removal of heavy metal ions from aqueous solution

Evaluation of biosurfactants grown in corn oil by Rhodococcus rhodochrous on removing of heavy metal ion from aqueous solution

Science.gov (United States)

Suryanti, Venty; Hastuti, Sri; Pujiastuti, Dwi

2016-02-01

The potential application of biosurfactants to remove heavy metal ion from aqueous solution by batch technique was examined. The glycolipids type biosurfactants were grown in a media containing of 20% v/v corn oil with 7 days of fermentation by Rhodococcus rhodochrous. The biosurfactants reduced the surface tension of water of about 51% from 62 mN/m to 30 mN/m. The biosurfactant increased the E24 of water-palm oil emulsion of about 55% from 43% to 97% and could maintain this E24 value of above 50% for up to 9 days. Heavy metal ion removal, in this case cadmium ion, by crude and patially purified biosurfactants has been investigated from aqueous solution at pH 6. Adsorption capacity of Cd(II) ion by crude biosurfactant with 5 and 10 minutes of contact times were 1.74 and 1.82 mg/g, respectively. Additionally, the adsorption capacity of Cd(II) ion by partially purified biosurfactant with 5 and 10 minutes of contact times were 0.79 and 1.34 mg/g, respectively. The results demonstrated that the adsorption capacity of Cd(II) ion by crude biosurfactant was higher than that of by partially purified biosurfactant. The results suggested that the biosurfactant could be used in the removal of heavy metal ions from aqueous solution.