Beam depolarization and gain saturation in neodymium rods with a diameter of 85 mm

Energy Technology Data Exchange (ETDEWEB)

Sukhanov, V N; Ugodenko, A A

1990-04-01

Depolarization and gain saturation were investigated in rod amplifiers using phosphate and silicate Nd glasses 85 mm in diameter and 300 mm in length at a pulse duration of 35 ns. Total depolarization losses over the rod cross section were measured for various radial distributions of the small-signal gain. For the phosphate glass the losses amounted to 3-6 percent; for the silicate glass, they amounted to 4-7 percent. Saturation energy densities of 4.5 + or - 0.4 and 8.0 + or - 0.7 J/sq cm were obtained for the phosphate and silicate glass, respectively. 8 refs.

Investigations on Important Properties of the 10 cm x 10 cm GEM Prototype

CERN Document Server

Saenboonruang, Kiadtisak; Kulasri, Kittipong; Ritthirong, Anawat

2015-01-01

The Gas Electron Multiplier (GEM) detector is one of promising particle and radiation detectors that has been improved greatly from previous gas detectors. The improvement includes better spatial resolutions, higher detection rate capabilities, and flexibilities in designs. In particular, the 10 cm x 10 cm GEM prototype is designed and provided by the Gas Detectors Development group (GDD) at CERN, Switzerland. With its simplicity in operations and designs, while still maintaining high qualities, the GEM prototype is suitable for both start-up and advanced researches. This article aims to report the investigations on some important properties of the 10 cm x 10 cm GEM detector using current measurement and signal counting. Results have shown that gains of the GEM prototype exponentially increase as voltage supplied to the detector increases, while the detector reaches full efficiency (plateau region) when the voltage is greater than 4100 V. In terms of signal sharing between X and Y strips of the readout, X str...

INSIG2 is Associated with Lower Gain in Weight-for-Length Between Birth and Age 6 Months

Directory of Open Access Journals (Sweden)

Ann Chen Wu

2009-01-01

Full Text Available Researchers have described the association of a common DNA polymorphism, rs7566605, near INSIG2 (insulin-induced gene 2 with obesity in multiple independent populations that include subjects ages 11–60 years.1 To our knowledge, no studies have examined the association of this polymorphism with weight status during early childhood. We explored the association of the rs7566605 polymorphism with weight-for-length among 319 children at 6 months and 3 years participating in Project Viva, a pre-birth cohort study. In contrast to studies of older individuals, CC homozygosity was associated with lower gain in weight-for-length z-score between birth and age 6 months than GG homozygosity or GC heterozygosity. At age 3, we did not find an association. The association of INSIG2 gene with obesity may change direction with age.

Penile length and circumference: an Indian study.

Science.gov (United States)

Promodu, K; Shanmughadas, K V; Bhat, S; Nair, K R

2007-01-01

Apprehension about the normal size of penis is a major concern for men. Aim of the present investigation is to estimate the penile length and circumference of Indian males and to compare the results with the data from other countries. Results will help in counseling the patients worried about the penile size and seeking penis enlargement surgery. Penile length in flaccid and stretched conditions and circumference were measured in a group of 301 physically normal men. Erected length and circumference were measured for 93 subjects. Mean flaccid length was found to be 8.21 cm, mean stretched length 10.88 cm and circumference 9.14 cm. Mean erected length was found to be 13.01 cm and erected circumference was 11.46 cm. Penile dimensions are found to be correlated with anthropometric parameters. Insight into the normative data of penile size of Indian males obtained. There are significant differences in the mean penile length and circumference of Indian sample compared to the data reported from other countries. Study need to be continued with a large sample to establish a normative data applicable to the general population.

The length of the male urethra

Directory of Open Access Journals (Sweden)

Tobias. S. Kohler

2008-08-01

Full Text Available PURPOSE: Catheter-based medical devices are an important component of the urologic armamentarium. To our knowledge, there is no population-based data regarding normal male urethral length. We evaluated the length of the urethra in men with normal genitourinary anatomy undergoing either Foley catheter removal or standard cystoscopy. MATERIALS AND METHODS: Male urethral length was obtained in 109 men. After study permission was obtained, the subject's penis was placed on a gentle stretch and the catheter was marked at the tip of the penis. The catheter was then removed and the distance from the mark to the beginning of the re-inflated balloon was measured. Alternatively, urethral length was measured at the time of cystoscopy, on removal of the cystoscope. Data on age, weight, and height was obtained in patients when possible. RESULTS: The mean urethral length was 22.3 cm with a standard deviation of 2.4 cm. Urethral length varied between 15 cm and 29 cm. No statistically significant correlation was found between urethral length and height, weight, body mass index (BMI, or age. CONCLUSIONS: Literature documenting the length of the normal male adult urethra is scarce. Our data adds to basic anatomic information of the male urethra and may be used to optimize genitourinary device design.

Gain-assisted broadband ring cavity enhanced spectroscopy

Science.gov (United States)

Selim, Mahmoud A.; Adib, George A.; Sabry, Yasser M.; Khalil, Diaa

2017-02-01

Incoherent broadband cavity enhanced spectroscopy can significantly increase the effective path length of light-matter interaction to detect weak absorption lines over broad spectral range, for instance to detect gases in confined environments. Broadband cavity enhancement can be based on the decay time or the intensity drop technique. Decay time measurement is based on using tunable laser source that is expensive and suffers from long scan time. Intensity dependent measurement is usually reported based on broadband source using Fabry-Perot cavity, enabling short measurement time but suffers from the alignment tolerance of the cavity and the cavity insertion loss. In this work we overcome these challenges by using an alignment-free ring cavity made of an optical fiber loop and a directional coupler, while having a gain medium pumped below the lasing threshold to improve the finesse and reduce the insertion loss. Acetylene (C2H2) gas absorption is measured around 1535 nm wavelength using a semiconductor optical amplifier (SOA) gain medium. The system is analyzed for different ring resonator forward coupling coefficient and loses, including the 3-cm long gas cell insertion loss and fiber connector losses used in the experimental verification. The experimental results are obtained for a coupler ratio of 90/10 and a fiber length of 4 m. The broadband source is the amplified spontaneous emission of another SOA and the output is measured using a 70pm-resolution optical spectrum analyzer. The absorption depth and the effective interaction length are improved about an order of magnitude compared to the direct absorption of the gas cell. The presented technique provides an engineering method to improve the finesse and, consequently the effective length, while relaxing the technological constraints on the high reflectivity mirrors and free-space cavity alignment.

Effect of the doped fibre length on soliton pulses of a bidirectional mode-locked fibre laser

Energy Technology Data Exchange (ETDEWEB)

Ahmad, H; Alwi Kutty, N A; Zulkifli, M Z; Harun, S W [Photonics Research Center (Department of Physics), University of Malaya, 50603 Kuala Lumpur (Malaysia)

2015-08-31

A passively bidirectional mode-locked fibre laser is demonstrated using a highly concentrated erbium-doped fibre (EDF) as a gain medium. To accomplish mode-locked operation in a short cavity, use is made of carbon nanotubes (CNTs) as a saturable absorber. Soliton pulses are obtained at a wavelength of 1560 nm with a repetition rate ranging from 43.92 MHz to 46.97 MHz and pulse width stretching from 0.56 ps to 0.41 ps as the EDF length is reduced from 60 cm to 30 cm. (lasers)

Sonographic Measurement of Normal Splenic Length in Korean Adults

Energy Technology Data Exchange (ETDEWEB)

Shin, Sang Bum; Cheon, Byung Kook; Kim, Jong Min; Oh, Kyung Seoung; Jung, Gyoo Sik; Huh, Jin Do; Joh, Young Duk [Kosin University College of Medicine, Busan (Korea, Republic of)

1996-12-15

To establish upper limit of normal splenic length of Korean adults on ultrasonography and to determice the degree of interobserver and intraobserver variation. Ultrasonographic scans were performed to measure the maximum length of spleen in 105 of 150 adults selected by convenience sampling. Remained 45 cases with any conditions that could alter splenic size were excluded from this study. The maximum length of spleen was measured and correlated with body surface area, patient height, weight, age and sex. In 31 of the 105 adults we evaluated the interobserver and intraobserver variations in sonographic measurements of splenic length obtained by three radiologists in blind fashion. The mean splenic length in 105 adults was 8.56cm ({+-} 0.95). The splenic length positively correlated with body surface area, patient height and weight (P <0.001), and negatively correlated with patient age (P < 0.01). Male spleen (8.87 cm {+-} 1.07) was longer than female spleen (8.35 cm {+-} 0.81) (P < 0.05). The following guidelines are proposed for the upper limit of normal splenic length at different groups of body surface area: no longer than 10 cm at 1.20{approx}1.59 m{sup 2}, 11 cm at1.60{approx}1.79 m{sup 2}, and 12 cm at 1.80{approx}1.99 m{sup 2}. The mean interobserver variation between any two radiologists ranged from 0.32 cm ({+-} 0.29) to 0.39 cm ({+-} 0.33) and interobserver variations were within 1 cm in 96%. The mean intraobserver variations were within 0.5 cm in 91%. The splenic length closely correlated with body surface area, patient height, weight and age. Particularly the upper limit of normal splenic length changed according to body surface area. Interobserver variation about 1 cm and intraobserver variation about 0.5 cm should be considered in the measurement of the splenic length on ultrasonography

Polarization dependence of the optical modal gain in ZnO

International Nuclear Information System (INIS)

Kim, Bumjin; Kyhm, Kwangseuk; Cho, Chaeryong

2010-01-01

The modal gain spectrum due to the electron-hole plasma in ZnO was measured using a variable stripe length method. A modal gain contour map for energy and stripe length allowed the modal gain saturation to be analyzed in terms of the spectral and the stripe length dependences. The modal gain was observed to be more significant in the TE mode than in the TM mode due to the polarization asymmetry of the wurtzite structure. We also found that the degree of polarization are enhanced as the stripe length increased, despite of modal gain saturation.

Assessment of colorectal length using the electromagnetic capsule tracking system

DEFF Research Database (Denmark)

Mark, E B; Poulsen, J L; Haase, A M

2017-01-01

AIM: We aimed to determine colorectal length with the 3D-Transit system by describing a 'centerline' of capsule movement and compare it to known anatomy, as determined by magnetic resonance imaging (MRI). Further, we aimed to test the day-to-day variation of colorectal length assessed......: Computation of colorectal length from capsule passage was possible in 60 of the 67 3D-Transit recordings. Length of the colorectum measured with MRI and 3D-Transit was respectively 95 cm (75-153 cm) and 99 cm (77-147 cm), P = 0.15. Coefficient of variation (CV) between MRI and 3D-Transit was 7.8%. Apart from...... the cecum / ascending colon being 26% (P = 0.002) shorter on MRI, there were no other differences in total or segmental colorectal lengths between methods (all P > 0.05). Length of the colorectum measured with 3D-Transit on two consecutive days was 102 cm (73-119 cm) and 103 cm (75-123 cm), P = 0.67. CV...

Backscatter measurements of 11-cm equatorial spread-F irregularities

International Nuclear Information System (INIS)

Tsunoda, R.T.

1980-01-01

In the equatorial F-region ionosphere, a turbulent cascade process has been found to exist that extends from irregularity spatial wavelengths longer than tens of kilometers down to wavelengths as short as 36 cm. To investigate the small-scale regime of wavelengths less than 36 cm, an equatorial radar experiment was conducted using a frequency of 1320 MHz that corresponds to an irregularity wavelength of 11 cm. The first observations of radar backscatter from 11-cm field-aligned irregularities (FAI) are described. These measurements extend the spatial wavelength regime of F-region FAI to lengths that approach both electron gyroradius and the Debye length. Agreement of these results with the theory of high-frequency drift waves suggests that these observations may be unique to the equatorial ionosphere. That is, the requirement of low electron densities for which the theroy calls may preclude the existence of 11-cm FAI elsewhere in the F-region ionosphere, except in equatorial plasma bubbles

Study of gain-coupled distributed feedback laser based on high order surface gain-coupled gratings

Science.gov (United States)

Gao, Feng; Qin, Li; Chen, Yongyi; Jia, Peng; Chen, Chao; Cheng, LiWen; Chen, Hong; Liang, Lei; Zeng, Yugang; Zhang, Xing; Wu, Hao; Ning, Yongqiang; Wang, Lijun

2018-03-01

Single-longitudinal-mode, gain-coupled distributed feedback (DFB) lasers based on high order surface gain-coupled gratings are achieved. Periodic surface metal p-contacts with insulated grooves realize gain-coupled mechanism. To enhance gain contrast in the quantum wells without the introduction of effective index-coupled effect, groove length and depth were well designed. Our devices provided a single longitudinal mode with the maximum CW output power up to 48.8 mW/facet at 971.31 nm at 250 mA without facet coating, 3dB linewidth (39 dB). Optical bistable characteristic was observed with a threshold current difference. Experimentally, devices with different cavity lengths were contrasted on power-current and spectrum characteristics. Due to easy fabrication technique and stable performance, it provides a method of fabricating practical gain-coupled distributed feedback lasers for commercial applications.

Length-weight and length-length relationships of common carp (Cyprinus carpio L.) in the middle and southern Iraq provinces

Science.gov (United States)

Al-jebory, Taymaa A.; Das, Simon K.; Usup, Gires; Bakar, Y.; Al-saadi, Ali H.

2018-04-01

In this study, length-weight and length-length relationships of common carp (Cyprinus carpio L.) in the middle and southern Iraq provinces were determined. Fish specimens were procured from seven provinces from July to December, 2015. A negative and positive allometric growth pattern was obtained, where the total length (TL) ranged from 25.60 cm to 33.53 cm, and body weight (BW) ranged from 700 g to 1423 g. Meanwhile, the lowest of 1.03 and highest of 3.54 in "b" value was recorded in group F and group C, respectively. Therefore, Fulton condition factor (K) range from 2.57 to 4.94. While, relative condition factor (Kn) was in the ranged of 0.95 to 1.01. A linear relationship between total length (TL) and standard length (SL) among the provinces for fish groups was obtained. The variances in "b" value ranged from 0.10 to 0.93 with correlation coefficient (r2) of 0.02 to 0.97. This research could be used as a guide to study the ecology and biology of common Carp (Cyprinus carpio L.) in the middle and southern Iraq provinces.

The length-weight and length-length relationships of bluefish, Pomatomus saltatrix (Linnaeus, 1766) from Samsun, middle Black Sea region

OpenAIRE

Özpiçak, Melek; Saygın, Semra; Polat, Nazmi

2017-01-01

In this study, length-weight relationship (LWR) and length-length relationship (LLR) of bluefish,Pomatomus saltatrix were determined. A total of 125 specimens were sampled from Samsun, themiddle Black Sea in 2014 fishing season. Bluefish specimens were monthly collected fromcommercial fishing boats from October to December 2014. All captured individuals (N=125) weremeasured to the nearest 0.1 cm for total, fork and standard lengths. The weight of each fish (W)was recorded to the nearest 0.01 ...

A STUDY OF CORRELATION OF FOOT LENGTH AND GESTATIONAL MATURITY IN NEONATES

Directory of Open Access Journals (Sweden)

M. Bhuvaneswari

2018-03-01

Full Text Available BACKGROUND Gestational age estimation at birth can be done by clinical estimation through careful history of LMP, ultrasonic estimation of gestational age, date of first recorded foetal activity “quickening” first felt at approximately 16-18 weeks, Date of first recorded foetal heart sounds. MATERIALS AND METHODS A study sample of 800 live newborns were selected by simple random sampling technique born at GVR hospital and Government General Hospital, Kurnool from April 2015 to May 2016. Data was collected using standard proforma meeting the objectives of the study. a Gestational age assessment was done using modified Bellard’s score and b Foot length was measured using sliding calipers which is having an accuracy of a millimeter. Following instruments are used: 1 Sliding calipers for measuring foot length, 2 Flexible, non-stretchable measuring tape for head circumference, 3 Infantometer for measuring crown heel length, 4 Electronic weighing scale for measuring weight. RESULTS The foot length of preterm neonates ranged from 4.5-7.8 cm with the mean foot length of 6.1571 cm and 6.6964 cm for preterm SGA and AGA, respectively. The foot length of term neonates ranged from 5.4-8.7 cm with a mean foot length of 7.0471 cm, 7.5703 cm, 8.0391 cm for term SGA, AGA, LGA respectively. The foot length for post term neonates ranged from 6.7-8.8 cm, with a mean foot length of 7.5688 cm, 8.0170 cm and 8.2667 cm for post term SGA, AGA and LGA, respectively. This shows that foot length increases as the gestational age increases. CONCLUSION Foot length can be correlated significantly with the gestational age, birth weight, head circumference and crown heel length.

Controlling morphology and chain aggregation in semiconducting conjugated polymers: the role of solvent on optical gain in MEH-PPV.

Science.gov (United States)

Lampert, Zach E; Reynolds, C Lewis; Papanikolas, John M; Aboelfotoh, M Osama

2012-10-25

We report the results of a detailed investigation that addresses the influence of polymer morphology and chain aggregation, as controlled by the chemical nature of the solvent, on the optical gain properties of the conjugated polymer poly[2-methoxy-5-(2'-ethylhexyloxy)-p-phenylene vinylene] (MEH-PPV). Using the variable stripe length technique in the picosecond regime, we have extensively studied the optical gain performance of asymmetric planar waveguides formed with thin MEH-PPV films spin-cast from concentrated chlorobenzene (CB) and tetrahydrofuran (THF) solutions onto thermally oxidized silicon substrates. CB and THF solvents were chosen based on their known ability to promote and effectively limit aggregate formation, respectively. Very large net gain coefficients are demonstrated, reaching values of 330 and 365 cm(-1), respectively, when optically pumping the waveguides with a maximum energy density of 85 μJ/cm(2). Our results clearly demonstrate that polymer morphology, and hence, the chain conformation dependence of the degree of aggregation in the films as controlled by the solvent, has minimal impact on the net gain. Moreover, the waveguides exhibit low loss coefficients of 10-20 cm(-1) at the ASE wavelength. These results question the importance of polymer morphology and aggregate formation in polymer-based optical devices operating at high excitation densities in the stimulated emission regime as would be characteristic of lasers and optical amplifiers.

Interobserver Variation of the Renal Length Measurement on Ultrasonography

International Nuclear Information System (INIS)

Jeong, Yoong Ki; Chung, Hye Weon; Kim, Tae Sung; Ryoo, Jae Wook; Kim, Tae Kyoung; Kim, Seung Hyup

1995-01-01

We assessed interobserver variation in the measurement of the renal length on ultrasonography. Ultrasonographic examinations were performed in randomly selected 50 patients. The maximallenhths of both kidneys were measured with calipers during the scanning from frozen images by three observers in a blinded fashion. There was a relatively constant tendency of an observer to measure a renal length either longer or shorter than the other observer(Kendall coefficient>0.05). Average interobserver variations were 0.51 cm (±0.42 cm) in right kidney and 0.53 cm (±0.41 cm) in left kidney and were within 1 cm in 91% right and 89% of left kidney. Interobserver variation about 1cm should be considered in the measurement of the renal length on ultrasonography

Peyronie's Reconstruction for Maximum Length and Girth Gain: Geometrical Principles

Directory of Open Access Journals (Sweden)

Paulo H. Egydio

2008-01-01

Full Text Available Peyronie's disease has been associated with penile shortening and some degree of erectile dysfunction. Surgical reconstruction should be based on giving a functional penis, that is, rectifying the penis with rigidity enough to make the sexual intercourse. The procedure should be discussed preoperatively in terms of length and girth reconstruction in order to improve patient satisfaction. The tunical reconstruction for maximum penile length and girth restoration should be based on the maximum length of the dissected neurovascular bundle possible and the application of geometrical principles to define the precise site and size of tunical incision and grafting procedure. As penile rectification and rigidity are required to achieve complete functional restoration of the penis and 20 to 54% of patients experience associated erectile dysfunction, penile straightening alone may not be enough to provide complete functional restoration. Therefore, phosphodiesterase inhibitors, self-injection, or penile prosthesis may need to be added in some cases.

Effects of physical activity during pregnancy and gestational weight gain on newborn weight and length at birth in Warmińsko-Mazurskie province.

Science.gov (United States)

Przybyłowicz, Katarzyna; Przybyłowicz, Mariusz; Grzybiak, Marek; Janiszewska, Katarzyna

2014-01-01

Epidemiological research has identified a relationship between maternal physical activity, early nutrition and infant birth weight with likelihood of developing future diseases. The aim of the study was to determine a relationship between gestational weight gain and physical activity during pregnancy to the nutritional status of newborns. The presented study was conducted in the period from February 2010 until November 2012 in the gynecological and obstetric clinics in Warmińsko-Mazurskie voivodeship with various levels of reference. The research subjects included 510 women in the puerperal period aged 18-36. The scope of the research included an assessment of the selected anthropometric parameters of both pregnant women (body mass, height, BMI, gestational weight gain) and newborns (infant birth weight, infant length, Ponderal Index), as well as an analysis of the connections between the gestational weight gain, physical activity during pregnancy and anthropometric parameters of newborns. In the study group there was a significant percentage of women characterised by an inactive lifestyle and excessive gestational weight gain. There were significantly higher neonatal birth anthropometric parameters in women with abnormal excessive gestational weight gain than in women with normal and inappropriate - low gestational weight gain. The highest percentage of women with appropriate weight gain was observed in the group of women who are physically active, although this requires confirmation in larger population. Our studies have not shown statistically significant differences between the gestational weight gain and nutritional status of newborns in relation to the level of physical activity of pregnant women.

Studies of flow configurations up to the critical phenomenon at 80 kg/cm2

International Nuclear Information System (INIS)

Raisson, C.

1968-12-01

Tests performed at 80 kg/cm 2 allow to study two-phase flows and their evolution up to the critical heating. Three measurement methods have been used simultaneously: thermocouples, conductivity probe, short length pressure drops after the output. The 282 cm length stainless steel channel has an internal diameter of 0.6 cm and a wall thickness of 0.2 cm. Flow configuration results are comparable to those of the literature with some precision regarding some transition zones. Two critical heating regimes have been highlighted. The results demonstrate the interest of the method and the importance of hydrodynamic parameters on the critical heating phenomenon [fr

Influences of finite gain bandwidth on pulse propagation in parabolic fiber amplifiers with distributed gain profiles

International Nuclear Information System (INIS)

Zhao Jia-Sheng; Li Pan; Chen Xiao-Dong; Feng Su-Juan; Mao Qing-He

2012-01-01

The evolutions of the pulses propagating in decreasing and increasing gain distributed fiber amplifiers with finite gain bandwidths are investigated by simulations with the nonlinear Schrödinger equation. The results show that the parabolic pulse propagations in both the decreasing and the increasing gain amplifiers are restricted by the finite gain bandwidth. For a given input pulse, by choosing a small initial gain coefficient and gain variation rate, the whole gain for the pulse amplification limited by the gain bandwidth may be higher, which is helpful for the enhancement of the output linearly chirped pulse energy. Compared to the decreasing gain distributed fiber amplifier, the increasing gain distributed amplifier may be more conducive to suppress the pulse spectral broadening and increase the critical amplifier length for achieving a larger output linearly chirped pulse energy

Theoretical investigation of the more suitable rare earth to achieve high gain in waveguide based on silica containing silicon nanograins doped with either Nd³+ or Er³+ ions.

Science.gov (United States)

Fafin, Alexandre; Cardin, Julien; Dufour, Christian; Gourbilleau, Fabrice

2014-05-19

We present a comparative study of the gain achievement in a waveguide whose active layer is constituted by a silica matrix containing silicon nanograins acting as sensitizer of either neodymium ions (Nd3+) or erbium ions (Er3+). By means of an auxiliary differential equation and finite difference time domain (ADE-FDTD) approach that we developed, we investigate the steady states regime of both rare earths ions and silicon nanograins levels populations as well as the electromagnetic field for different pumping powers ranging from 1 to 104 mW/mm2. Moreover, the achievable gain has been estimated in this pumping range. The Nd3+ doped waveguide shows a higher gross gain per unit length at 1064 nm (up to 30 dB/cm) than the one with Er3+ doped active layer at 1532 nm (up to 2 dB/cm). Taking into account the experimental background losses we demonstrate that a significant positive net gain can only be achieved with the Nd3+ doped waveguide.

LENGTH-WEIGHT RELATIONSHIP AND CONDITION FACTOR OF ...

African Journals Online (AJOL)

Data Collection and Analysis. The measurements of length (cm), weight (g) and the condition factor of individual fish sampled were recorded. The relationship between length and weight of the fish was examined by simple linear regression using WINKS software. The variations in the length-weight represented by 'b' were.

Impact of Martial Arts (Judo, Karate, and Kung Fu) on Bone Mineral Density Gains in Adolescents of Both Genders: 9-Month Follow-Up.

Science.gov (United States)

Ito, Igor H; Kemper, Han C G; Agostinete, Ricardo R; Lynch, Kyle R; Christofaro, Diego G D; Ronque, Enio R; Fernandes, Rômulo A

2017-11-01

To compare bone mineral density (BMD) gains in adolescents of both genders stratified according to different martial art styles in a 9-month follow-up study. The longitudinal study consisted of 29 adolescents of both genders and age between 11 and 17 years stratified into a control group (not engaged in any sport) and 50 fighters (kung fu/karate, n = 29; judo, n = 21). All 79 subjects underwent anthropometric measures (weight, height, leg length, and height set) and dual-energy X-ray absorptiometry (BMD, in g/cm 2 ) at 2 moments, baseline and 9 months later. Maturity offset (age at peak height velocity), lean soft tissue, chronological age, and resistance training were treated as covariates. Male judoists presented higher gains in BMD-spine [0.098 g/cm 2 (95% confidence interval, 0.068-0.128)] than control group [0.040 g/cm 2 (95% confidence interval, 0.011-0.069)] (post hoc test with P = .030). There was no effect of martial art on BMD gains among girls. Independently of gender, in all multivariate models, lean soft tissue constituted the most relevant covariate. Judo practice in adolescents affected the bone accrual significantly after 9-month follow-up compared with controls, mainly in boys.

Weight gain following treatment of hyperthyroidism.

Science.gov (United States)

Dale, J; Daykin, J; Holder, R; Sheppard, M C; Franklyn, J A

2001-08-01

Patients frequently express concern that treating hyperthyroidism will lead to excessive weight gain. This study aimed to determine the extent of, and risk factors for, weight gain in an unselected group of hyperthyroid patients. We investigated 162 consecutive hyperthyroid patients followed for at least 6 months. Height, weight, clinical features, biochemistry and management were recorded at each clinic visit. Documented weight gain was 5.42 +/- 0.46 kg (mean +/- SE) and increase in BMI was 8.49 +/- 0.71%, over a mean 24.2 +/- 1.6 months. Pre-existing obesity, Graves' disease causing hyperthyroidism, weight loss before presentation and length of follow-up each independently predicted weight gain. Patients treated with thionamides or radioiodine gained a similar amount of weight (thionamides, n = 87, 5.16 +/- 0.63 kg vs. radioiodine, n = 62, 4.75 +/- 0.57 kg, P = 0.645), but patients who underwent thyroidectomy (n = 13) gained more weight (10.27 +/- 2.56 kg vs. others, P = 0.007). Development of hypothyroidism (even transiently) was associated with weight gain (never hypothyroid, n = 102, 4.57 +/- 0.52 kg, transiently hypothyroid, n = 29, 5.37 +/- 0.85 kg, on T4, n = 31, 8.06 +/- 1.42 kg, P = 0.014). This difference remained after correcting for length of follow-up. In the whole cohort, weight increased by 3.95 +/- 0.40 kg at 1 year (n = 144) to 9.91 +/- 1.62 kg after 4 years (n = 27) (P = 0.008), representing a mean weight gain of 3.66 +/- 0.44 kg/year. We have demonstrated marked weight gain after treatment of hyperthyroidism. Pre-existing obesity, a diagnosis of Graves' disease and prior weight loss independently predicted weight gain and weight continued to rise with time. Patients who became hypothyroid, despite T4 replacement, gained most weight.

Detecting cm-scale hot spot over 24-km-long single-mode fiber by using differential pulse pair BOTDA based on double-peak spectrum.

Science.gov (United States)

Diakaridia, Sanogo; Pan, Yue; Xu, Pengbai; Zhou, Dengwang; Wang, Benzhang; Teng, Lei; Lu, Zhiwei; Ba, Dexin; Dong, Yongkang

2017-07-24

In distributed Brillouin optical fiber sensor when the length of the perturbation to be detected is much smaller than the spatial resolution that is defined by the pulse width, the measured Brillouin gain spectrum (BGS) experiences two or multiple peaks. In this work, we propose and demonstrate a technique using differential pulse pair Brillouin optical time-domain analysis (DPP-BOTDA) based on double-peak BGS to enhance small-scale events detection capability, where two types of single mode fiber (main fiber and secondary fiber) with 116 MHz Brillouin frequency shift (BFS) difference have been used. We have realized detection of a 5-cm hot spot at the far end of 24-km single mode fiber by employing a 50-cm spatial resolution DPP-BOTDA with only 1GS/s sampling rate (corresponding to 10 cm/point). The BFS at the far end of 24-km sensing fiber has been measured with 0.54 MHz standard deviation which corresponds to a 0.5°C temperature accuracy. This technique is simple and cost effective because it is implemented using the similar experimental setup of the standard BOTDA, however, it should be noted that the consecutive small-scale events have to be separated by a minimum length corresponding to the spatial resolution defined by the pulse width difference.

Combined optical gain and degradation measurements in DCM2 doped Tris-(8-hydroxyquinoline)aluminum thin-films

Science.gov (United States)

Čehovski, Marko; Döring, Sebastian; Rabe, Torsten; Caspary, Reinhard; Kowalsky, Wolfgang

2016-04-01

Organic laser sources offer the opportunity to integrate flexible and widely tunable lasers in polymer waveguide circuits, e.g. for Lab-on-Foil applications. Therefore, it is necessary to understand gain and degradation processes for long-term operation. In this paper we address the challenge of life-time (degradation) measurements of photoluminescence (PL) and optical gain in thin-film lasers. The well known guest-host system of aluminum-chelate Alq3 (Tris-(8-hydroxyquinoline)aluminum) as host material and the laser dye DCM2 (4-(Dicyanomethylene)-2- methyl-6-julolidyl-9-enyl-4H-pyran) as guest material is employed as laser active material. Sample layers have been built up by co-evaporation in an ultrahigh (UHV) vacuum chamber. 200nm thick films of Alq3:DCM2 with different doping concentrations have been processed onto glass and thermally oxidized silicon substrates. The gain measurements have been performed by the variable stripe length (VSL) method. This measurement technique allows to determine the thin-film waveguide gain and loss, respectively. For the measurements the samples were excited with UV irradiation (ƛ = 355nm) under nitrogen atmosphere by a passively Q-switched laser source. PL degradation measurements with regard to the optical gain have been done at laser threshold (approximately 3 μJ/cm2), five times above laser threshold and 10 times above laser threshold. A t50-PL lifetime of > 107 pulses could be measured at a maximum excitation energy density of 32 μJ/cm2. This allows for a detailed analysis of the gain degradation mechanism and therefore of the stimulated cross section. Depending on the DCM2 doping concentration C the stimulated cross section was reduced by 35 %. Nevertheless, the results emphasizes the necessity of the investigation of degradation processes in organic laser sources for long-term applications.

Circular polarization with crossed-planar undulators in high-gain FELs

CERN Document Server

Kim, K J K J

2000-01-01

We propose a crossed undulator configuration for a high-gain free-electron laser to allow versatile polarization control. This configuration consists of a long (saturation length) planar undulator, a dispersive section, and a short (a few gain lengths) planar undulator oriented perpendicular to the first one. In the first undulator, a radiation component linearly polarized in the x-direction is amplified to saturation. In the second undulator, the x-polarized component propagates freely, while a new component, polarized in the y-direction, is generated and reaches saturation in a few gain lengths. By adjusting the strength of the dispersive section, the relative phase of two radiation components can be adjusted to obtain a suitable polarization for the total radiation field, including the circular polarization. The operating principle of the high-gain crossed undulator, which is quite different from that of the crossed undulator for spontaneous radiation, is illustrated in terms of 1-D FEL theory.

Measurement of population inversions and gain in carbon fiber plasmas

International Nuclear Information System (INIS)

Milchberg, H.; Skinner, C.H.; Suckewer, S.; Voorhees, D.

1985-10-01

A CO 2 laser (approx.0.5 kJ energy, 70 nsec pulse width) was focussed onto the end of an axially oriented, thick (35 to 350 μ) carbon fiber with or without a magnetic field present along the laser-fiber axis. We present evidence for axial-to-transverse enhancement of the CVI 182A (n = 3 → 2) transition, which is correlated with the appearance of a population inversion between levels n = 3 and 2. For the B = 0 kG, zero field case, the maximum gain-length product of kl approx. =3 (k approx. =6 cm -1 ) was measured for a carbon fiber coated with a thin layer of aluminum (for additional radiation cooling). The results are interpreted in terms of fast recombination due mostly to thermal conduction from the plasma to the cold fiber core

Pole lengths influence O2-cost during double poling in highly trained cross-country skiers.

Science.gov (United States)

Carlsen, Camilla Høivik; Rud, Bjarne; Myklebust, Håvard; Losnegard, Thomas

2018-02-01

In elite cross-country skiing, double poling is used in different terrain. This study compared O 2 -cost and kinematics during double poling with four different pole lengths [self-selected (SS), SS - 5 cm, SS + 5 cm, SS + 10 cm] at Low versus Moderate incline. Thirteen highly trained male cross-country skiers (mean ± SD 23 ± 3 years; 182 ± 4 cm; 77 ± 6 kg) completed eight submaximal trials with roller skis on a treadmill at two conditions: "Low incline" (1.7°; 4.5 m s -1 ) and "Moderate incline" (4.5°; 2.5 m s -1 ) with each of the four pole lengths. O 2 -cost and 3D body kinematics were assessed in each trial. In Low incline, SS + 10 cm induced a lower O 2 -cost than all the other pole lengths [P size (ES) 0.5-0.8], whereas no differences were found between the remaining pole lengths (P > 0.05; ES 0.2-0.4). In Moderate incline, significant differences between all pole lengths were found for O 2 -cost, with SS - 5 cm > SS > SS + 5 cm > SS + 10 cm (P differences in O 2 -cost between SS and the other pole lengths were greater in Moderate incline than Low incline (SS - 5 cm; 1.5%, ES 0.8, SS + 5 cm; 1.3%, ES 1.0, and SS + 10 cm; 1.9%, ES 1.0, all P difference was found in cycle, poling or reposition times between pole lengths. However, at both conditions a smaller total vertical displacement of center of mass was observed with SS + 10 cm compared to the other pole lengths. Increasing pole length from SS - 5 cm to SS + 10 cm during double poling induced lower O 2 -cost and this advantage was greater in Moderate compared to Low incline.

Effects of Probiotics on Necrotizing Enterocolitis, Sepsis, Intraventricular Hemorrhage, Mortality, Length of Hospital Stay, and Weight Gain in Very Preterm Infants: A Meta-Analysis.

Science.gov (United States)

Sun, Jing; Marwah, Gayatri; Westgarth, Matthew; Buys, Nicholas; Ellwood, David; Gray, Peter H

2017-09-01

Probiotics are increasingly used as a supplement to prevent adverse health outcomes in preterm infants. We conducted a systematic review, meta-analysis, and subgroup analysis of findings from randomized controlled trials (RCTs) to assess the magnitude of the effect of the probiotics on health outcomes among very-low-birth-weight (VLBW) infants. Relevant articles from January 2003 to June 2017 were selected from a broad range of databases, including Medline, PubMed, Scopus, and Embase. Studies were included if they used an RCT design, involved a VLBW infant (birthweight probiotic intervention group, measured necrotizing enterocolitis (NEC) as a primary outcome, and measured sepsis, mortality, length of hospital stay, weight gain, and intraventricular hemorrhage (IVH) as additional outcomes. The initial database search yielded 132 potentially relevant articles and 32 ( n = 8998 infants) RCTs were included in the final meta-analysis. Subgroup analysis was used to evaluate the effects of the moderators on the outcome variables. In the probiotics group, it was found that NEC was reduced by 37% (95% CI: 0.51%, 0.78%), sepsis by 37% (95% CI: 0.72%, 0.97%), mortality by 20% (95% CI: 0.67%, 0.95%), and length of hospital stay by 3.77 d (95% CI: -5.94, -1.60 d). These findings were all significant when compared with the control group. There was inconsistent use of strain types among some of the studies. The results indicate that probiotic consumption can significantly reduce the risk of developing medical complications associated with NEC and sepsis, reduce mortality and length of hospital stay, and promote weight gain in VLBW infants. Probiotics are more effective when taken in breast milk and formula form, consumed for Probiotics are not effective in reducing the incidence of IVH in VLBW infants. © 2017 American Society for Nutrition.

The effects of different pot length and growing media on seedling ...

African Journals Online (AJOL)

The aim of this study was to determine appropriate pot length and growing medium for Crimean Juniper seedlings (Juniperus excelsa Bieb.), which will be used for afforestation of extreme areas. For this purpose, polyethylene pots of 11 cm width and 20, 25 and 30 cm lengths were used. As growing medium, 13 different ...

16 CFR 500.12 - Measurement of commodities by length and width, how expressed.

Science.gov (United States)

2010-01-01

... square foot (929 cm2) be expressed in terms of length and width in linear measure. The customary inch... of 1 square foot (929 cm2) or more, but less than 4 square feet (37.1 dm2), be expressed in terms of... (10.16 cm) or less, the declaration of net quantity shall be expressed in terms of width and length in...

New Finnish growth references for children and adolescents aged 0 to 20 years: Length/height-for-age, weight-for-length/height, and body mass index-for-age.

Science.gov (United States)

Saari, Antti; Sankilampi, Ulla; Hannila, Marja-Leena; Kiviniemi, Vesa; Kesseli, Kari; Dunkel, Leo

2011-05-01

Growth curves require regular updates due to secular trends in linear growth. We constructed contemporary growth curves, assessed secular trends in height, and defined body mass index (BMI) cut-off points for thinness, overweight, and obesity in Finnish children. Mixed cross-sectional/longitudinal data of 73,659 healthy subjects aged 0-20 years (born 1983-2008) were collected from providers in the primary health care setting. Growth references for length/height-for-age, weight-for-length/height, and BMI-for-age were fitted using generalized additive models for location, scale, and shape (GAMLSS). BMI percentile curves passing through BMIs 30, 25, 18.5, 17, and 16 kg/m(2) at the age of 18 years were calculated to define limits for obesity, overweight, and various grades of thinness. Increased length/height-for-age was seen in virtually all age-groups when compared to previous Finnish growth data from 1959 to 1971. Adult height was increased by 1.9 cm in girls and 1.8 cm in boys. The largest increases were seen during the peripubertal years: up to 2.8 cm in girls and 5.6 cm in boys. Median weight-for-length/height had not increased. New Finnish references for length/height-for-age, weight-for-length/height, and BMI-for-age were constructed and should be implemented to monitor growth of children in Finland.

5cm aperture dipole studies

International Nuclear Information System (INIS)

McInturff, A.D.; Bossert, R.; Carson, J.; Fisk, H.E.; Hanft, R.; Kuchnir, M.; Lundy, R.; Mantech, P.; Strait, J.

1986-01-01

The results obtained during the evolution of the design, construction, and testing program of the design ''B'' dipole are presented here. Design ''B'' is one of the original three competing designs for the Superconducting Super Collider ''SSC'' arc dipoles. The final design parameters were as follows: air cored (less than a few percent of the magnetic field derived from any iron present), aluminum collared, two layered winding, 5.5T maximum operating field, and a 5 cm cold aperture. There have been fourteen 64 cm long 5 cm aperture model dipoles cold tested (at 4.3K and less) in this program so far. There was a half length full size (6m) mechanical analog (M-10) built and tested to check the cryostat's mechanical design under ramping and quench conditions. Several deviations from the ''Tevatron'' dipole fabrication technique were incorporated, for example the use of aluminum collars instead of stainless steel. The winding technique variations explored were ''dry welding,'' a technique with the cable covered with Kapton insulation only and ''wet winding'' where the Kapton was covered with a light coat of ''B'' stage epoxy. Test data include quench currents, field quality (Fourier multipole co-efficients), coil magnetization, conductor current performance, and coil loading. Quench current, loss per cycle, and harmonics were measured as a function of the magnitude and rate of change of the magnetic field, and helium bath temperature

Application of soft x-ray laser interferometry to study large-scale-length, high-density plasmas

International Nuclear Information System (INIS)

Wan, A.S.; Barbee, T.W., Jr.; Cauble, R.

1996-01-01

We have employed a Mach-Zehnder interferometer, using a Ne-like Y x- ray laser at 155 Angstrom as the probe source, to study large-scale- length, high-density colliding plasmas and exploding foils. The measured density profile of counter-streaming high-density colliding plasmas falls in between the calculated profiles using collisionless and fluid approximations with the radiation hydrodynamic code LASNEX. We have also performed simultaneous measured the local gain and electron density of Y x-ray laser amplifier. Measured gains in the amplifier were found to be between 10 and 20 cm -1 , similar to predictions and indicating that refraction is the major cause of signal loss in long line focus lasers. Images showed that high gain was produced in spots with dimensions of ∼ 10 μm, which we believe is caused by intensity variations in the optical drive laser. Measured density variations were smooth on the 10-μm scale so that temperature variations were likely the cause of the localized gain regions. We are now using the interferometry technique as a mechanism to validate and benchmark our numerical codes used for the design and analysis of high-energy-density physics experiments. 11 refs., 6 figs

Derivation of Conditions for the Normal Gain Behavior of Conical Horns

Directory of Open Access Journals (Sweden)

Chin Yeng Tan

2007-01-01

Full Text Available Monotonically increasing gain-versus-frequency pattern is in general expected to be a characteristic of aperture antennas that include the smooth-wall conical horn. While optimum gain conical horns do naturally exhibit this behavior, nonoptimum horns need to meet certain criterion: a minimum axial length for given aperture diameter, or, alternatively, a maximum aperture diameter for the given axial length. In this paper, approximate expressions are derived to determine these parameters.

The effect of distal ulnar implant stem material and length on bone strains.

Science.gov (United States)

Austman, Rebecca L; Beaton, Brendon J B; Quenneville, Cheryl E; King, Graham J W; Gordon, Karen D; Dunning, Cynthia E

2007-01-01

Implant design parameters can greatly affect load transfer from the implant stem to the bone. We have investigated the effect of length or material of distal ulnar implant stems on the surrounding bone strains. Eight cadaveric ulnas were instrumented with 12 strain gauges and secured in a customized jig. Strain data were collected while loads (5-30 N) were applied to the medial surface of the native ulnar head. The native ulnar head was removed, and a stainless steel implant with an 8-cm-long finely threaded stem was cemented into the canal. After the cement had cured, the 8-cm stem was removed, leaving a threaded cement mantle in the canal that could accept shorter threaded stems of interest. The loading protocol was then repeated for stainless steel stems that were 7, 5, and 3 cm in length, as well as for a 5-cm-long titanium alloy (TiAl(6)V(4)) stem. Other stainless steel stem lengths between 3 and 7 cm were tested at intervals of 0.5 cm, with only a 20 N load applied. No stem length tested matched the native strains at all gauge locations. No significant differences were found between any stem length and the native bone at the 5th and 6th strain gauge positions. Strains were consistently closer to the native bone strains with the titanium stem than the stainless steel stem for each gauge pair that was positioned on the bone overlying the stem. The 3-cm stem results were closer to the native strains than the 7-cm stem for all loads at gauges locations that were on top of the stem. The results from this study suggest that the optimal stem characteristics for distal ulnar implants from a load transfer point of view are possessed by shorter (approximately 3 to 4 cm) titanium stems.

Short Rayleigh Length Free Electron Lasers

CERN Document Server

Crooker, P P; Armstead, R L; Blau, J

2004-01-01

Conventional free electron laser (FEL) oscillators minimize the optical mode volume around the electron beam in the undulator by making the resonator Rayleigh length about one third of the undulator length. This maximizes gain and beam-mode coupling. In compact configurations of high-power infrared FELs or moderate power UV FELs, the resulting optical intensity can damage the resonator mirrors. To increase the spot size and thereby reduce the optical intensity at the mirrors below the damage threshold, a shorter Rayleigh length can be used, but the FEL interaction is significantly altered. A new FEL interaction is described and analyzed with a Rayleigh length that is only one tenth the undulator length, or less. The effect of mirror vibration and positioning are more critical in the short Rayleigh length design, but we find that they are still within normal design tolerances.

Short Rayleigh length free electron lasers

Directory of Open Access Journals (Sweden)

W. B. Colson

2006-03-01

Full Text Available Conventional free electron laser (FEL oscillators minimize the optical mode volume around the electron beam in the undulator by making the resonator Rayleigh length about one third to one half of the undulator length. This maximizes gain and beam-mode coupling. In compact configurations of high-power infrared FELs or moderate power UV FELs, the resulting optical intensity can damage the resonator mirrors. To increase the spot size and thereby reduce the optical intensity at the mirrors below the damage threshold, a shorter Rayleigh length can be used, but the FEL interaction is significantly altered. We model this interaction using a coordinate system that expands with the rapidly diffracting optical mode from the ends of the undulator to the mirrors. Simulations show that the interaction of the strongly focused optical mode with a narrow electron beam inside the undulator distorts the optical wave front so it is no longer in the fundamental Gaussian mode. The simulations are used to study how mode distortion affects the single-pass gain in weak fields, and the steady-state extraction in strong fields.

Characterization of transient gain x-ray lasers

International Nuclear Information System (INIS)

Dunn, J.; Osterheld, A.; Shlyaptsev, V.

1999-01-01

We have performed numerical simulations of the transient collisional excitation Ni-like Pd 4d → 4p J = 0 → 1 147 angstrom laser transition recently observed at Lawrence Livermore National Laboratory (LLNL). The high gain ∼35 cm results from the experiment are compared with detailed modeling simulations from the 1-D RADEX code in order to better understand the main physics issues affecting the measured gain and x-ray laser propagation along the plasma column. Simulations indicate that the transient gain lifetime associated with the short pulse pumping and refraction of the x-ray laser beam out of the gain region are the main detrimental effects. Gain lifetimes of ∼7 ps(1/e decay) are inferred from the smoothly changing gain experimental observations and are in good agreement with the simulations. Furthermore, the modeling results indicate the presence of a longer-lived but lower gain later in time associated with the transition from transient to quasi-steady state excitation

The cross-correlation of the CMB polarization and the 21-cm line fluctuations from cosmic reionization

NARCIS (Netherlands)

Tashiro, Hiroyuki; Aghanim, Nabila; Langer, Mathieu; Douspis, Marian; Zaroubi, Saleem

2008-01-01

The cosmic microwave background (CMB) polarization and the 21-cm line fluctuations are powerful probes of cosmological reionization. We study how the cross-correlation between the CMB polarization (E modes) and the 21-cm line fluctuations can be used to gain further understanding of the reionization

Single crystalline Er{sub 2}O{sub 3}:sapphire films as potentially high-gain amplifiers at telecommunication wavelength

Energy Technology Data Exchange (ETDEWEB)

Kuznetsov, A. S.; Sadofev, S.; Schäfer, P.; Kalusniak, S.; Henneberger, F., E-mail: fh@physik.hu-berlin.de [Institut für Physik, Humboldt-Universität zu Berlin, Newtonstr. 15, D-12489 Berlin (Germany)

2014-11-10

Single crystalline thin films of Er{sub 2}O{sub 3}, demonstrating efficient 1.5 μm luminescence of Er{sup 3+} at room temperature were grown on Al{sub 2}O{sub 3} substrate by molecular beam epitaxy. The absorption coefficient at 1.536 μm was found to reach 270 cm{sup −1} translating in a maximal possible gain of 1390 dBcm{sup −1}. In conjunction with the 10% higher refractive index as compared to Al{sub 2}O{sub 3}, this opens the possibility to use Er{sub 2}O{sub 3}:sapphire films as short-length waveguide amplifiers in telecommunication.

Gain bandwidth of 80 nm and 2 dB/cm peak gain in Al2O3:Er3+ optical amplifiers on silicon

NARCIS (Netherlands)

Bradley, J.; Agazzi, L.; Geskus, D.; Ay, F.; Worhoff, Kerstin; Pollnau, Markus

Erbium-doped aluminum oxide integrated optical amplifiers were fabricated on silicon substrates, and their characteristics were investigated for Er concentrations ranging from 0.27 to 4.2x10e20 cm−3. Background losses below 0.3 dB/cm at 1320 nm were measured. For optimum Er concentrations in the

Weight gain in newborns submitted to skin-to-skin contact

Directory of Open Access Journals (Sweden)

Ana Karine da Costa Monteiro Souza

Full Text Available ABSTRACT Purpose: to compare the weight gain among newborns submitted to the kangaroo method and those not submitted to it, and to analyze the factors that may influence this gain: length of hospital stay, gestational age, corrected gestational age, birth weight, weight on the first day of follow-up, duration of gastric tube feeding, duration of oral feeding, and type of diet. Methods: a cross-sectional, quantitative study, with 86 newborns divided into two groups: group 1, with 48 neonates undergoing skin-to-skin contact and Group 2, 38 newborns who did not have this contact. Weights were recorded until hospital discharge. Results: a greater weight gain in Group 1, a longer time of hospitalization in Group 2, and a significant difference in weight gain related to the type of diet in Group 2. Conclusion: skin-to-skin contact has a positive influence on weight gain and length of hospital stay of newborns. The use of an infant formula does not influence weight gain for dyads who experienced skin-to-skin contact. Gestational age, corrected gestational age, birth weight, weight on the first day of follow-up, duration of gastric tube feeding, duration of oral feeding are not correlated with weight gain.

The significance of stricture length and prior treatments

African Journals Online (AJOL)

Results: The median age was 49.5 years (range 21–90), median stricture length was 4 cm (range 1–18 cm) and the overall recurrence rate was 27.8%. Postinfectious strictures, pan urethral strictures or multiple strictures involving the penile and bulbar urethra were more common. Most patients had penile circular ...

Fundamental length

International Nuclear Information System (INIS)

Pradhan, T.

1975-01-01

The concept of fundamental length was first put forward by Heisenberg from purely dimensional reasons. From a study of the observed masses of the elementary particles known at that time, it is sumrised that this length should be of the order of magnitude 1 approximately 10 -13 cm. It was Heisenberg's belief that introduction of such a fundamental length would eliminate the divergence difficulties from relativistic quantum field theory by cutting off the high energy regions of the 'proper fields'. Since the divergence difficulties arise primarily due to infinite number of degrees of freedom, one simple remedy would be the introduction of a principle that limits these degrees of freedom by removing the effectiveness of the waves with a frequency exceeding a certain limit without destroying the relativistic invariance of the theory. The principle can be stated as follows: It is in principle impossible to invent an experiment of any kind that will permit a distintion between the positions of two particles at rest, the distance between which is below a certain limit. A more elegant way of introducing fundamental length into quantum theory is through commutation relations between two position operators. In quantum field theory such as quantum electrodynamics, it can be introduced through the commutation relation between two interpolating photon fields (vector potentials). (K.B.)

Energy performance of windows based on the net energy gain

DEFF Research Database (Denmark)

Svendsen, Svend; Kragh, Jesper; Laustsen, Jacob Birck

2005-01-01

The paper presents a new method to set up energy performance requirements and energy classes for windows of all dimensions and configurations. The net energy gain of windows is the solar gain minus the heat loss integrated over the heating season. The net energy gain can be calculated for one...... be expressed as a function of two parameters representing the energy performance and two parameters representing the geometry of the window. The two energy performance parameters are the net energy gain per area of the glazing unit and the sum of the heat losses through the frame and the assembly per length...... of the frame. The two geometry numbers are the area of the glazing unit relative to the window area and the length of the frame profiles relative to the window area. Requirements and classes for the energy performance of the window can be given by assigning values to the two energy performance parameters...

Potential of solar-simulator-pumped alexandrite lasers

Science.gov (United States)

Deyoung, Russell J.

1990-01-01

An attempt was made to pump an alexandrite laser rod using a Tamarak solar simulator and also a tungsten-halogen lamp. A very low optical laser cavity was used to achieve the threshold minimum pumping-power requirement. Lasing was not achieved. The laser threshold optical-power requirement was calculated to be approximately 626 W/sq cm for a gain length of 7.6 cm, whereas the Tamarak simulator produces 1150 W/sq cm over a gain length of 3.3 cm, which is less than the 1442 W/sq cm required to reach laser threshold. The rod was optically pulsed with 200 msec pulses, which allowed the alexandrite rod to operate at near room temperature. The optical intensity-gain-length product to achieve laser threshold should be approximately 35,244 solar constants-cm. In the present setup, this product was 28,111 solar constants-cm.

[Renal length measured by ultrasound in adult mexican population].

Science.gov (United States)

Oyuela-Carrasco, J; Rodríguez-Castellanos, F; Kimura, E; Delgado-Hernández, R; Herrera-Félix, J P

2009-01-01

Renal length estimation by ultrasound is an important parameter in clinical evaluation of kidney disease and healthy donors. Changes in renal volume may be a sign of kidney disease. Correct interpretation of renal length requires the knowledge of normal limits, these have not been described for Latin American population. To describe normal renal length (RL) by ultrasonography in a group of Mexican adults. Ultrasound measure of RL in 153 healthy Mexican adults stratified by age. Describe the association of RL to several anthropometric variables. A total of 77 males and 76 females were scanner. The average age for the group was 44.12 +/- 15.44 years. The mean weight, body mass index (BMI) and height were 68.87 +/- 11.69 Kg, 26.77 +/- 3.82 kg/m2 and 160 +/- 8.62 cm respectively. Dividing the population by gender, showed a height of 166 +/- 6.15 cm for males and 154.7 +/- 5.97 cm for females (p =0.000). Left renal length (LRL) in the whole group was 105.8 +/- 7.56 mm and right renal length (RRL) was 104.3 +/- 6.45 mm (p = 0.000.) The LRL for males was 107.16 +/- 6.97 mm and for females was 104.6 +/- 7.96 mm. The average RRL for males was 105.74 +/- 5.74 mm and for females 102.99 +/- 6.85 mm (p = 0.008.) We noted that RL decreased with age and the rate of decline accelerates alter 60 years of age. Both lengths correlated significantly and positively with weight, BMI and height. The RL was significantly larger in males than in females in both kidneys (p = 0.036) in this Mexican population. Renal length declines after 60 years of age and specially after 70 years.

Radiation cooling and gain calculation for C VI 182 A line in C/Se plasma

International Nuclear Information System (INIS)

Nam, C.H.; Valeo, E.; Suckewer, S.; Feldman, U.

1986-04-01

A model is developed which is capable of describing the evolution of gain resulting from both rapid radiative and expansion cooling of a recombining, freely expanding plasma. It is demonstrated for the particular case of a carbon/selenium plasma that the cooling rate which leads to optimal gain can be achieved by adjusting the admixture of an efficiently radiating material (selenium) in the gain medium (carbon). Comparison is made to a recent observation of gain in a recent NRL/Rochester experiment with carbon/selenium plasma for the n = 3 → 2 transition in C VI occurring at 182 A. The predicted maximum gain is approx.10 cm -1 , as compared to observation of 2 to 3 cm -1

Metallographic study of reconstitution welding in inserts of 1 cm{sup 3}; Estudio metalografico de soldaduras de reconstitucion en insertos de 1 cm{sup 3}

Energy Technology Data Exchange (ETDEWEB)

Romero C, J.; Garcia R, R.; Fernandez T, F.; Perez R, N.; Rocamontes A, M. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

2007-07-01

In this article, the welding metallographic study carried out in Charpy test tubes reconstituted with notch in 'V', used in the surveillance programs of the vessel in nucleo electric plants is described. Inserts of 1 cm{sup 3} are used, where the inserts are usually rectangular of minimum 18 millimeters of length. The importance of using inserts of 1 cm{sup 3} is that the mechanical properties can be measured in another direction of the vessel steel, when changing the direction or sense of the notch in 'V' or the face where this notch is made in the insert. (Author)

Pilot production of 4 sq cm ITO/InP photovoltaic solar cells

Science.gov (United States)

Gessert, T. A.; Li, X.; Coutts, T. J.; Tzafaras, N.

1991-01-01

Experimental results of a pilot production of 32 4-sq cm indium tin oxide (ITO)InP space solar cells are presented. The discussion includes analysis of the device performance of the best cells produced as well as the performance range of all production cells. The experience gained from the production is discussed, indicating other issues that may be encountered when large-scale productions are initiated. Available data on a 4-sq cm ITO/InP cell that was flown on the UoSAT-5 satellite is reported.

Overview of bunch length measurements

International Nuclear Information System (INIS)

Lumpkin, A. H.

1999-01-01

An overview of particle and photon beam bunch length measurements is presented in the context of free-electron laser (FEL) challenges. Particle-beam peak current is a critical factor in obtaining adequate FEL gain for both oscillators and self-amplified spontaneous emission (SASE) devices. Since measurement of charge is a standard measurement, the bunch length becomes the key issue for ultrashort bunches. Both time-domain and frequency-domain techniques are presented in the context of using electromagnetic radiation over eight orders of magnitude in wavelength. In addition, the measurement of microbunching in a micropulse is addressed

Metallographic study of reconstitution welding in inserts of 1 cm3

International Nuclear Information System (INIS)

Romero C, J.; Garcia R, R.; Fernandez T, F.; Perez R, N.; Rocamontes A, M.

2007-01-01

In this article, the welding metallographic study carried out in Charpy test tubes reconstituted with notch in 'V', used in the surveillance programs of the vessel in nucleo electric plants is described. Inserts of 1 cm 3 are used, where the inserts are usually rectangular of minimum 18 millimeters of length. The importance of using inserts of 1 cm 3 is that the mechanical properties can be measured in another direction of the vessel steel, when changing the direction or sense of the notch in 'V' or the face where this notch is made in the insert. (Author)

Gastrocnemius fascicle and achilles tendon length at the end of the eccentric phase in a single and multiple countermovement hop.

Science.gov (United States)

Lidstone, Daniel E; van Werkhoven, Herman; Needle, Alan R; Rice, Paige E; McBride, Jeffrey M

2018-02-01

The purpose of this investigation was to compare fascicle and tendon length of the gastrocnemius at the end of the eccentric phase during a hop utilizing a single countermovement (sCM) versus multiple countermovement (mCM1, mCM2, mCM3) strategy. Seventeen healthy males performed nine hopping trials of sCM and nine trials of mCM. Ankle and knee joint angle and lower leg length from videography and muscle ultrasound were used to calculate muscle-tendon unit (MTU), fascicle and tendon length. Sacral marker data was used to determine hopping height. Force- and displacement-time curves were utilized to calculate work. Muscle activity of the lateral and medial gastrocnemius was also measured. Fascicle length was significantly shorter (mCM3: 6.2 ± 1.5 cm, sCM: 7.3 ± 2.0 cm) and tendon length was significantly longer (mCM3: 36.5 ± 3.6 cm, sCM: 35.5 ± 3.8 cm) at the end of the eccentric phase in mCM3 in comparison to sCM. Maximal hopping height (mCM: 14.6 ± 3.1 cm, sCM: 13.1 ± 2.5 cm), eccentric phase gastrocnemius muscle activity (mCM medial gastrocnemius: 0.10 ± 0.03 mV, mCM lateral gastrocnemius: 0.08 ± 0.04 mV, sCM medial gastrocnemius: 0.07 ± 0.03 mV, sCM lateral gastrocnemius: 0.05 ± 0.04 mV), and both eccentric (mCM3: 46.6 ± 19.4 J, sCM: 38.5 ± 15.9 J) and concentric work (mCM3: 87.6 ± 26.5 J, sCM: 80.9 ± 27.6 J) were significantly higher for mCM3 compared to sCM. The results indicate that a multiple countermovement hop strategy results in shorter fascicle length and longer tendon length at the end of the eccentric phase. In addition, greater eccentric phase muscle activity during the third countermovement (mCM3) in comparison to a single countermovement hop (sCM) was observed. A multiple countermovement strategy appears to result in higher hopping height and greater work done in both the eccentric and concentric phase indicating possible contribution of stored

The BRIDGE HadCM3 family of climate models: HadCM3@Bristol v1.0

Science.gov (United States)

Valdes, Paul J.; Armstrong, Edward; Badger, Marcus P. S.; Bradshaw, Catherine D.; Bragg, Fran; Crucifix, Michel; Davies-Barnard, Taraka; Day, Jonathan J.; Farnsworth, Alex; Gordon, Chris; Hopcroft, Peter O.; Kennedy, Alan T.; Lord, Natalie S.; Lunt, Dan J.; Marzocchi, Alice; Parry, Louise M.; Pope, Vicky; Roberts, William H. G.; Stone, Emma J.; Tourte, Gregory J. L.; Williams, Jonny H. T.

2017-10-01

Understanding natural and anthropogenic climate change processes involves using computational models that represent the main components of the Earth system: the atmosphere, ocean, sea ice, and land surface. These models have become increasingly computationally expensive as resolution is increased and more complex process representations are included. However, to gain robust insight into how climate may respond to a given forcing, and to meaningfully quantify the associated uncertainty, it is often required to use either or both ensemble approaches and very long integrations. For this reason, more computationally efficient models can be very valuable tools. Here we provide a comprehensive overview of the suite of climate models based around the HadCM3 coupled general circulation model. This model was developed at the UK Met Office and has been heavily used during the last 15 years for a range of future (and past) climate change studies, but has now been largely superseded for many scientific studies by more recently developed models. However, it continues to be extensively used by various institutions, including the BRIDGE (Bristol Research Initiative for the Dynamic Global Environment) research group at the University of Bristol, who have made modest adaptations to the base HadCM3 model over time. These adaptations mean that the original documentation is not entirely representative, and several other relatively undocumented configurations are in use. We therefore describe the key features of a number of configurations of the HadCM3 climate model family, which together make up HadCM3@Bristol version 1.0. In order to differentiate variants that have undergone development at BRIDGE, we have introduced the letter B into the model nomenclature. We include descriptions of the atmosphere-only model (HadAM3B), the coupled model with a low-resolution ocean (HadCM3BL), the high-resolution atmosphere-only model (HadAM3BH), and the regional model (HadRM3B). These also include

Brain SPECT with short focal-length cone-beam collimation

International Nuclear Information System (INIS)

Park, Mi-Ae; Moore, Stephen C.; Kijewski, Marie Foley

2005-01-01

Single-photon emission-computed tomography (SPECT) imaging of deep brain structures is compromised by loss of photons due to attenuation. We have previously shown that a centrally peaked collimator sensitivity function can compensate for this phenomenon, increasing sensitivity over most of the brain. For dual-head instruments, parallel-hole collimators cannot provide variable sensitivity without simultaneously degrading spatial resolution near the center of the brain; this suggests the use of converging collimators. We have designed collimator pairs for dual-head SPECT systems to increase sensitivity, particularly in the center of the brain, and compared the new collimation approach to existing approaches on the basis of performance in estimating activity concentration of small structures at various locations in the brain. The collimator pairs we evaluated included a cone-beam collimator, for increased sensitivity, and a fan-beam collimator, for data sufficiency. We calculated projections of an ellipsoidal uniform background, with 0.9-cm-radius spherical lesions at several locations in the background. From these, we determined ideal signal-to-noise ratios (SNR CRB ) for estimation of activity concentration within the spheres, based on the Cramer-Rao lower bound on variance. We also reconstructed, by an ordered-subset expectation-maximization (OS-EM) procedure, images of this phantom, as well as of the Zubal brain phantom, to allow visual assessment and to ensure that they were free of artifacts. The best of the collimator pairs evaluated comprised a cone-beam collimator with 20 cm focal length, for which the focal point is inside the brain, and a fan-beam collimator with 40 cm focal length. This pair yielded increased SNR CRB , compared to the parallel-parallel pair, throughout the imaging volume. The factor by which SNR CRB increased ranged from 1.1 at the most axially extreme location to 3.5 at the center. The gains in SNR CRB were relatively robust to mismatches

Optical gain in InAs/InGaAs quantum-dot structures: Experiments and theoretical model

International Nuclear Information System (INIS)

Eliseev, P G; Li, H; Liu, G T; Stintz, A; Newell, T C; Lester, L E; Malloy, K J

2000-01-01

The dependence of the mode optical gain on current in InAs/InGaAs quantum-dot structures grown by the method of molecular-beam epitaxy is obtained from the experimental study of ultra-low-threshold laser diodes. The record lowest inversion threshold at room temperature was about 13 A cm -2 . A theoretical model is proposed that relates the optical gain to the ground-state transitions in quantum dots. The effective gain cross section is estimated to be ∼7 x 10 -15 cm -2 . (lasers)

Racial/ethnic variations in perineal length and association with perineal lacerations: a prospective cohort study.

Science.gov (United States)

Yeaton-Massey, Amanda; Wong, Luchin; Sparks, Teresa N; Handler, Stephanie J; Meyer, Michelle R; Granados, Jesus M; Stasenko, Marina; Sit, Anita; Caughey, Aaron B

2015-02-01

To examine the association between race/ethnicity, perineal length and the risk of perineal laceration. This is a prospective cohort study of a diverse group of women with singleton gestations in the third trimester of pregnancy. Perineal length was measured and mean values calculated for several racial/ethnic groups. Chi-squared analyses were used to examine rates of severe perineal laceration (third or fourth degree laceration) by race/ethnicity among women considered to have a short perineal length. Further, subgroup analyses were performed comparing nulliparas to multiparas. Among 344 study participants, there was no statistically significant difference in mean perineal length by race/ethnicity (White 4.0 ± 1.1 cm, African-American 3.7 ± 1.0 cm, Latina 4.1 ± 1.1 cm, Asian 3.8 ± 1.0 cm, and other/unknown 4.0 ± 0.9 cm). Considering parity, more multiparous Asian and African-American women had a short perineal length (20.7 and 23.5%, respectively, p = 0.05). Finally, the rate of severe perineal lacerations in our cohort was 2.6% overall, but was 8.2% among Asian women (p = 0.04). We did not find a relationship between short perineal length and risk of severe perineal laceration with vaginal delivery, or a difference in mean perineal length by maternal race/ethnicity. However, we did find that women of different racial/ethnic groups have varying rates of severe perineal laceration, with Asian women comprising the highest proportion.

Gain optimization method of a DQW superluminescent diode with broad multi-state emission

KAUST Repository

Dimas, Clara E.

2010-01-01

Optimizing gain through systematic methods of varying current injection schemes analytically is significant to maximize experimentally device yield and evaluation. Various techniques are used to calculate the amplified spontaneous emission (ASE) gain for light emitting devices consisting of single-section and multiple-sections of even length. Recently double quantum well (DQW) superluminescent diodes (SLD) have shown a broad multi-state emission due to mutlielectrodes of non-equal lengths and at high non-equal current densities. In this study, we adopt an improved method utilizing an ASE intensity ratio to calibrate a gain curve based on the sum of the measured ASE spectra to efficiently estimate the gain. Although the laser gain for GaAs/AlGaAs material is well studied, the ASE gain of SLD devices has not been systematically studied particular to further explain the multiple-state emission observed in fabricated devices. In addition a unique gain estimate was achieved where the excited state gain clamps prior to the ground state due to approaching saturation levels. In our results, high current densities in long sectioned active regions achieved sufficient un-truncated gain that show evidence of excited state emission has been observed.

Microdose acquisition in adolescent leg length discrepancy using a low-dose biplane imaging system.

Science.gov (United States)

Jensen, Janni; Mussmann, Bo R; Hjarbæk, John; Al-Aubaidi, Zaid; Pedersen, Niels W; Gerke, Oke; Torfing, Trine

2017-09-01

Background Children with leg length discrepancy often undergo repeat imaging. Therefore, every effort to reduce radiation dose is important. Using low dose preview images and noise reduction software rather than diagnostic images for length measurements might contribute to reducing dose. Purpose To compare leg length measurements performed on diagnostic images and low dose preview images both acquired using a low-dose bi-planar imaging system. Material and Methods Preview and diagnostic images from 22 patients were retrospectively collected (14 girls, 8 boys; mean age, 12.8 years; age range, 10-15 years). All images were anonymized and measured independently by two musculoskeletal radiologists. Three sets of measurements were performed on all images; the mechanical axis lines of the femur and the tibia as well as the anatomical line of the entire extremity. Statistical significance was tested with a paired t-test. Results No statistically significant difference was found between measurements performed on the preview and on the diagnostic image. The mean tibial length difference between the observers was -0.06 cm (95% confidence interval [CI], -0.12 to 0.01) and -0.08 cm (95% CI, -0.21 to 0.05), respectively; 0.10 cm (95% CI, 0.02-0.17) and 0.06 cm (95% CI, -0.02 to 0.14) for the femoral measurements and 0.12 cm (95% CI, -0.05 to 0.26) and 0.08 cm (95% CI, -0.02 to 0.19) for total leg length discrepancy. ICCs were >0.99 indicating excellent inter- and intra-rater reliability. Conclusion The data strongly imply that leg length measurements performed on preview images from a low-dose bi-planar imaging system are comparable to measurements performed on diagnostic images.

Customization of biliopancreatic limb length to modulate and sustain antidiabetic effect of gastric bypass surgery.

Science.gov (United States)

Pal, A; Rhoads, D B; Tavakkoli, A

2018-02-01

Although Roux-en-Y Gastric Bypass (RYGB) remains the most effective treatment for obesity and type 2 diabetes (T2D), many patients fail to achieve remission, or relapse. Increasing intestinal limb lengths of RYGB may improve outcomes, but the mechanistic basis for this remains unclear. We hypothesize biliopancreatic (BP) limb length modulates the antidiabetic effect of RYGB. Rats underwent RYGB with a 20-cm (RYGB-20cm) or 40-cm (RYGB-40cm) BP limb and were compared with control animals. After 2 and 4 wk, portal and systemic blood was sampled during intestinal glucose infusion. Portosystemic gradient was used to calculate intestinal glucose utilization (G util ), absorption (G absorp ), and hormone secretion. Intestinal morphology and gene expression were assessed. At 2 wk, G absorp progressively decreased with increasing BP limb length; this pattern persisted at 4 wk. G util increased ≈70% in both RYGB-20cm and -40cm groups at 2 wk. At 4 wk, G util progressively increased with limb length. Furthermore, Roux limb weight, and expression of hexokinase and preproglucagon, exhibited a similar progressive increase. At 4 wk, glucagon-like peptide-1 and -2 levels were higher after RYGB-40cm, with associated increased secretion. We conclude that BP limb length modulates multiple antidiabetic mechanisms, analogous to the dose-response relationship of a drug. Early postoperatively, a longer BP limb reduces G absorp . Later, G util , Roux limb hypertrophy, hormone secretion, and hormone levels are increased with longer BP limb. Sustained high incretin levels may prevent weight regain and T2D relapse. These data provide the basis for customizing BP limb length according to patient characteristics and desired metabolic effect. NEW & NOTEWORTHY Biliopancreatic limb length in gastric bypass modulates multiple antidiabetic mechanisms, analogous to the dose-response relationship of a drug. With a longer biliopancreatic limb, Roux limb hypertrophy, increased glucose utilization

Coating process optimization through in-line monitoring for coating weight gain using Raman spectroscopy and design of experiments.

Science.gov (United States)

Kim, Byungsuk; Woo, Young-Ah

2018-05-30

In this study the authors developed a real-time Process Analytical Technology (PAT) of a coating process by applying in-line Raman spectroscopy to evaluate the coating weight gain, which is a quantitative analysis of the film coating layer. The wide area illumination (WAI) Raman probe was connected to the pan coater for real-time monitoring of changes in the weight gain of coating layers. Under the proposed in-line Raman scheme, a non-contact, non-destructive analysis was performed using WAI Raman probes with a spot size of 6 mm. The in-line Raman probe maintained a focal length of 250 mm, and a compressed air line was designed to protect the lens surface from spray droplets. The Design of Experiment (DOE) was applied to identify factors affecting the Raman spectra background of laser irradiation. The factors selected for DOE were the strength of compressed air connected to the probe, and the shielding of light by the transparent door connecting the probe to the pan coater. To develop a quantitative model, partial least squares (PLS) models as multivariate calibration were developed based on the three regions showing the specificity of TiO 2 individually or in combination. For the three single peaks (636 cm -1 , 512 cm -1 , 398 cm -1 ), least squares method (LSM) was applied to develop three univariate quantitative analysis models. One of best multivariate quantitative model having a factor of 1 gave the lowest RMSEP of 0.128, 0.129, and 0.125, respectively for prediction batches. When LSM was applied to the single peak at 636 cm -1 , the univariate quantitative model with an R 2 of 0.9863, slope of 0.5851, and y-intercept of 0.8066 had the lowest RMSEP of 0.138, 0.144, and 0.153, respectively for prediction batches. The in-line Raman spectroscopic method for the analysis of coating weight gain was verified by considering system suitability and parameters such as specificity, range, linearity, accuracy, and precision in accordance with ICH Q2 regarding

Economic issues of broiler production length

Directory of Open Access Journals (Sweden)

Szőllősi László

2014-01-01

Full Text Available The length of broiler production cycle is also an important factor when profitability is measured. This paper is to determine the effects of different market ages and down-time period, overall broiler production cycle length on performance and economic parameters based on Hungarian production and financial circumstances. A deterministic model was constructed to manage the function-like correlations of age-related daily weight gain, daily feed intake and daily mortality data. The results show that broiler production cycle length has a significant effect on production and economic performance. Cycle length is determined by the length of down-time and grow-out periods. If down-time period is reduced by one day, an average net income of EUR 0.55 per m2 is realizable. However, the production period is not directly proportional either with emerging costs or obtainable revenues. Profit maximization is attainable if the production period is 41-42 days.

Leg length, sitting height, and body proportions references for achondroplasia: New tools for monitoring growth.

Science.gov (United States)

Del Pino, Mariana; Ramos Mejía, Rosario; Fano, Virginia

2018-04-01

Achondroplasia is the most common form of inherited disproportionate short stature. We report leg length, sitting height, and body proportion curves for achondroplasia. Seven centile format of sitting height, leg length, sitting height/leg length ratio, sitting height/height ratio, and head circumference/height ratio were estimated by the LMS method. The Q-test was applied to assess the goodness of fit. For comparison, centiles of sitting height and leg length were graphed using Argentine national growth references for achondroplasia and non-achondroplasia populations. The sample consisted of 342 children with achondroplasia (171 males, 171 females) aged 0-18 years. The median (interquartile range) number of measurements per child was 6 (3, 12) for sitting height and 8 (3, 13) for head circumference. Median leg length increased from 14 cm at age 1 week to 44 and 40 cm (males and females, respectively) in achondroplasia adolescents which is 3.5 cm shorter than non-achondroplasia children at age 1 week and, 38 cm shorter at adolescence. Median sitting height increased from 34 cm at birth to 86 and 81 in adolescents' boys and girls respectively, only 5 cm shorter than non-achondroplasia children. Sitting height/leg length decreased from 2.61 at birth to approximately 1.90 at adolescent. Median head circumference/height ratio decreased from 0.79 at birth to 0.46 at 18 years in both sexes. Growth of lower limbs is affected early in life and becomes more noticeable throughout childhood. The disharmonic growth between the less affected trunk and the severely affected limbs determine body disproportion in achondroplasia. © 2018 Wiley Periodicals, Inc.

Length of urethra in the Indian adult male population

Directory of Open Access Journals (Sweden)

Venkatesh Krishnamoorthy

2012-01-01

Full Text Available Objective: The urethral length has not been measured in the Indian population. Even the international literature in this arena is very sparse. This paper is an attempt to develop a simple anatomical database for urethral length. Materials and Methods: Between January 2010 and April 2011, the urethral lengths of 422 adult male patients who required catheterization as part of regular treatment at our hospital, were recorded after obtaining consent from the patients and from the scientific and ethics review boards of the institution. Patients with history of prostatic or urethral abnormalities were excluded. The balloon of a sterile Foley′s catheter was inflated using 10 cc of saline. The length from the junction of the balloon to the ′Y′ junction of the Foley was measured. The catheter was then passed into the bladder and re-inflated to same volume. The penis was gently straightened and the length of the catheter outside the penis was measured till the premarked point at the ′Y′ junction. Subtracting this from the original length gave the length of the urethra. Results: The mean length of the urethra was 17.55 + 1.42 cm with a range between 14 and 22.5 cm. Conclusions: Literature in which the length of the normal adult male urethra is recorded for a significant sample size is very scarce. Our data adds to basic anatomic information of the male urethra specific to the Indian population. Statistical Methods: Descriptive statistical analysis was performed. The non-linear regression analysis was employed to find the normative values of urethral length according to age class.

Measurement of the diffusion length of thermal neutrons in the beryllium oxide

International Nuclear Information System (INIS)

Koechlin, J.C.; Martelly, J.; Duggal, V.P.

1955-01-01

The diffusion length of thermal neutrons in the beryllium oxide has been obtained while studying the spatial distribution of the neutrons in a massive parallelepiped of this matter placed before the thermal column of the reactor core of Saclay. The mean density of the beryllium oxide (BeO) is 2,95 gr/cm 3 , the mean density of the massif is 2,92 gr/cm 3 . The value of the diffusion length, deducted of the done measures, is: L = 32,7 ± 0,5 cm (likely gap). Some remarks are formulated about the influence of the spectral distribution of the neutrons flux used. (authors) [fr

Bedside prediction of right subclavian venous catheter insertion length

Directory of Open Access Journals (Sweden)

Yoon Ji Choi

2014-12-01

Full Text Available Background and objective: The present study aimed to evaluate whether right subclavian vein (SCV catheter insertion depth can be predicted reliably by the distances from the SCV insertion site to the ipsilateral clavicular notch directly (denoted as I-IC, via the top of the SCV arch, or via the clavicle (denoted as I-T-IC and I-C-IC, respectively. Method: In total, 70 SCV catheterizations were studied. The I-IC, I-T-IC, and I-C-IC distances in each case were measured after ultrasound-guided SCV catheter insertion. The actual length of the catheter between the insertion site and the ipsilateral clavicular notch, denoted as L, was calculated by using chest X-ray. Results: L differed from the I-T-IC, I-C-IC, and I-IC distances by 0.14±0.53, 2.19±1.17, and -0.45 ±0.68 cm, respectively. The mean I-T-IC distance was the most similar to the mean L (intraclass correlation coefficient = 0.89. The mean I-IC was significantly shorter than L, while the mean I-C-IC was significantly longer. Linear regression analysis provided the following formula: Predicted SCV catheter insertion length (cm = -0.037 + 0.036 × Height (cm + 0.903 × I-T-IC (cm (adjusted r2 =0.64. Conclusion: The I-T-IC distance may be a reliable bedside predictor of the optimal insertion length for a right SCV cannulation.

Uniform laser ablative acceleration of targets at 1014 W/cm2

International Nuclear Information System (INIS)

Obenschain, S.P.; Whitlock, R.R.; McLean, E.A.; Ripin, B.H.; Price, R.H.; Phillion, D.W.; Campbell, E.M.; Rosen, M.D.

1982-01-01

We present the first detailed investigations of the ablative acceleration of planar targets while simultaneously using high irradiance (10 14 W/cm 2 ), large focal diameters (1 mm) and long laser pulse duration (3 nsec). Included are measurements of target preheat, ablation pressures and uniformity achieved under these conditions. Targets were accelerated to high velocities with velocity profile uniformity approaching that required for high gain pellet implosions

The effect of cutting length on the rooting and growth of subtropical ...

African Journals Online (AJOL)

The length of a cutting can affect both the rooting and plug colonisation of container-grown stock. Using hedges from conventional clonebanks established in the ground, four cutting length treatments (13, 10, 8 and 5 cm) were tested using five Eucalyptus grandis × E. urophylla clones. The smallest cutting length had the ...

Hydrodynamic simulations of long-scale-length two-plasmon–decay experiments at the Omega Laser Facility

International Nuclear Information System (INIS)

Hu, S. X.; Michel, D. T.; Edgell, D. H.; Froula, D. H.; Follett, R. K.; Goncharov, V. N.; Myatt, J. F.; Skupsky, S.; Yaakobi, B.

2013-01-01

Direct-drive–ignition designs with plastic CH ablators create plasmas of long density scale lengths (L n ≥ 500 μm) at the quarter-critical density (N qc ) region of the driving laser. The two-plasmon–decay (TPD) instability can exceed its threshold in such long-scale-length plasmas (LSPs). To investigate the scaling of TPD-induced hot electrons to laser intensity and plasma conditions, a series of planar experiments have been conducted at the Omega Laser Facility with 2-ns square pulses at the maximum laser energies available on OMEGA and OMEGA EP. Radiation–hydrodynamic simulations have been performed for these LSP experiments using the two-dimensional hydrocode draco. The simulated hydrodynamic evolution of such long-scale-length plasmas has been validated with the time-resolved full-aperture backscattering and Thomson-scattering measurements. draco simulations for CH ablator indicate that (1) ignition-relevant long-scale-length plasmas of L n approaching ∼400 μm have been created; (2) the density scale length at N qc scales as L n (μm)≃(R DPP ×I 1/4 /2); and (3) the electron temperature T e at N qc scales as T e (keV)≃0.95×√(I), with the incident intensity (I) measured in 10 14 W/cm 2 for plasmas created on both OMEGA and OMEGA EP configurations with different-sized (R DPP ) distributed phase plates. These intensity scalings are in good agreement with the self-similar model predictions. The measured conversion fraction of laser energy into hot electrons f hot is found to have a similar behavior for both configurations: a rapid growth [f hot ≃f c ×(G c /4) 6 for G c hot ≃f c ×(G c /4) 1.2 for G c ≥ 4, with the common wave gain is defined as G c =3 × 10 −2 ×I qc L n λ 0 /T e , where the laser intensity contributing to common-wave gain I qc , L n , T e at N qc , and the laser wavelength λ 0 are, respectively, measured in [10 14 W/cm 2 ], [μm], [keV], and [μm]. The saturation level f c is observed to be f c ≃ 10 –2 at around

Does length of common limb influence remission of diabetes? Short-term results

Directory of Open Access Journals (Sweden)

Ramraj V Nagendra Gupta

2016-01-01

Full Text Available Background: Despite strict patient selection criteria, diabetes remission is not seen in all patients after gastric bypass. Can length of the common limb influence diabetes remission? Aim: To find if any correlation exists between the length of the common limb and remission of diabetes. Study Design: Prospective study. Materials and Methods: Twenty-five consecutive patients with Type II diabetes mellitus and a fasting C-peptide >1 ng/ml who underwent laparoscopic Roux-en-y gastric bypass were included. All patients had standard limb lengths and length of the common limb was measured in all patients. Patients were followed up and glycated haemoglobin (HbA1c was repeated at 6 months postoperatively. Pre- and postoperative HbA1c were then correlated with the lengths of common limb to look for any relation. Statistical Analysis: Descriptive and inferential statistical analysis, analysis of variance (ANOVA. Results: Of the 25 patients, 15 were females and 10 were males. The mean age was 44.16 years and the mean body mass index (BMI was 43.96 kg/m 2 . Preoperative HbA1c varied from 5.8 to 12.3%. Length of the common limb varied from 210 to 790 cm (mean 470.4 cm. HbA1c at 6 months ranged from 4.8 to 7.7% (mean 5.81%. On comparison of preoperative and 6 months postoperative HbA1c and correlating with the length of common limb, we found that patients with a common limb of length 600 cm length (P = 0.004. Conclusion: A shorter common limb does appear to have better chances of resolution of Type II diabetes mellitus in our study, thus paving the way for further studies.

Amplification of Frequency-Modulated Similariton Pulses in Length-Inhomogeneous Active Fibers

Directory of Open Access Journals (Sweden)

I. O. Zolotovskii

2012-01-01

Full Text Available The possibility of an effective gain of the self-similar frequency-modulated (FM wave packets is studied in the length-inhomogeneous active fibers. The dynamics of parabolic pulses with the constant chirp has been considered. The optimal profile for the change of the group-velocity dispersion corresponding to the optimal similariton pulse amplification has been obtained. It is shown that the use of FM pulses in the active (gain and length-inhomogeneous optical fibers with the normal group-velocity dispersion can provide subpicosecond optical pulse amplification up to the energies higher than 1 nJ.

Ultra-high gain diffusion-driven organic transistor

Science.gov (United States)

Torricelli, Fabrizio; Colalongo, Luigi; Raiteri, Daniele; Kovács-Vajna, Zsolt Miklós; Cantatore, Eugenio

2016-01-01

Emerging large-area technologies based on organic transistors are enabling the fabrication of low-cost flexible circuits, smart sensors and biomedical devices. High-gain transistors are essential for the development of large-scale circuit integration, high-sensitivity sensors and signal amplification in sensing systems. Unfortunately, organic field-effect transistors show limited gain, usually of the order of tens, because of the large contact resistance and channel-length modulation. Here we show a new organic field-effect transistor architecture with a gain larger than 700. This is the highest gain ever reported for organic field-effect transistors. In the proposed organic field-effect transistor, the charge injection and extraction at the metal–semiconductor contacts are driven by the charge diffusion. The ideal conditions of ohmic contacts with negligible contact resistance and flat current saturation are demonstrated. The approach is general and can be extended to any thin-film technology opening unprecedented opportunities for the development of high-performance flexible electronics. PMID:26829567

Standing Height and its Estimation Utilizing Foot Length Measurements in Adolescents from Western Region in Kosovo

Directory of Open Access Journals (Sweden)

Stevo Popović

2017-10-01

Full Text Available The purpose of this research is to examine standing height in both Kosovan genders in the Western Region as well as its association with foot length, as an alternative to estimating standing height. A total of 664 individuals (338 male and 326 female participated in this research. The anthropometric measurements were taken according to the protocol of ISAK. The relationships between body height and foot length were determined using simple correlation coefficients at a ninety-five percent confidence interval. A comparison of means of standing height and foot length between genders was performed using a t-test. After that a linear regression analysis were carried out to examine extent to which foot length can reliably predict standing height. Results displayed that Western Kosovan male are 179.71±6.00cm tall and have a foot length of 26.73±1.20cm, while Western Kosovan female are 166.26±5.23cm tall and have a foot length of 23.66±1.06cm. The results have shown that both genders made Western-Kosovans a tall group, a little bit taller that general Kosovan population. Moreover, the foot length reliably predicts standing height in both genders; but, not reliably enough as arm span. This study also confirms the necessity for developing separate height models for each region in Kosovo as the results from Western-Kosovans don’t correspond to the general values.

Synthesis of aerogel tiles with high light scattering length

CERN Document Server

Danilyuk, A F; Okunev, A G; Onuchin, A P; Shaurman, S A

1999-01-01

The possibility of aerogel tiles production for RICH detectors is described. Monolithic blocks of silica aerogel were synthesized by two-step sol-gel processing of tetraethoxysilane Si(OEt) sub 4 followed by high temperature supercritical drying with organic solvent. The important characteristic of aerogel is the light scattering length. In the wide range of refraction indexes the light scattering length exceeds 4 cm at 400 nm.

The BRIDGE HadCM3 family of climate models: HadCM3@Bristol v1.0

Directory of Open Access Journals (Sweden)

P. J. Valdes

2017-10-01

Full Text Available Understanding natural and anthropogenic climate change processes involves using computational models that represent the main components of the Earth system: the atmosphere, ocean, sea ice, and land surface. These models have become increasingly computationally expensive as resolution is increased and more complex process representations are included. However, to gain robust insight into how climate may respond to a given forcing, and to meaningfully quantify the associated uncertainty, it is often required to use either or both ensemble approaches and very long integrations. For this reason, more computationally efficient models can be very valuable tools. Here we provide a comprehensive overview of the suite of climate models based around the HadCM3 coupled general circulation model. This model was developed at the UK Met Office and has been heavily used during the last 15 years for a range of future (and past climate change studies, but has now been largely superseded for many scientific studies by more recently developed models. However, it continues to be extensively used by various institutions, including the BRIDGE (Bristol Research Initiative for the Dynamic Global Environment research group at the University of Bristol, who have made modest adaptations to the base HadCM3 model over time. These adaptations mean that the original documentation is not entirely representative, and several other relatively undocumented configurations are in use. We therefore describe the key features of a number of configurations of the HadCM3 climate model family, which together make up HadCM3@Bristol version 1.0. In order to differentiate variants that have undergone development at BRIDGE, we have introduced the letter B into the model nomenclature. We include descriptions of the atmosphere-only model (HadAM3B, the coupled model with a low-resolution ocean (HadCM3BL, the high-resolution atmosphere-only model (HadAM3BH, and the regional model (HadRM3B

Modeling relaxation length and density of acacia mangium wood using gamma - ray attenuation technique

International Nuclear Information System (INIS)

Tamer A Tabet; Fauziah Abdul Aziz

2009-01-01

Wood density measurement is related to the several factors that influence wood quality. In this paper, density, relaxation length and half-thickness value of eight ages, 3, 5, 7, 10, 11, 13 and 15 year-old of Acacia mangium wood were determined using gamma radiation from 137 Cs source. Results show that Acacia mangium tree of age 3 year has the highest relaxation length of 83.33 cm and least density of 0.43 gcm -3 , while the tree of age 15 year has the least Relaxation length of 28.56 cm and highest density of 0.76 gcm -3 . Results also show that the 3 year-old Acacia mangium wood has the highest half thickness value of 57.75 cm and 15 year-old tree has the least half thickness value of 19.85 cm. Two mathematical models have been developed for the prediction of density, variation with relaxation length and half-thickness value of different age of tree. A good agreement (greater than 85% in most cases) was observed between the measured values and predicted ones. Very good linear correlation was found between measured density and the age of tree (R2 = 0.824), and between estimated density and Acacia mangium tree age (R2 = 0.952). (Author)

A megajoule class krypton fluoride amplifier for single shot, high gain ICF application

International Nuclear Information System (INIS)

Rose, E.; Hanson, D.; Krohn, B.; McLeod, J.; Kang, M.

1988-01-01

A design study is underway to define the optimal architecture for a KrF laser system which will deliver 10 MJ of 248-nm light to an ICF target. We present one approach which incorporates final power amplifiers in the megajoule class, achieving 10 MJ with four final amplifiers. Each double-pass laser amplifier employs two-sided electron-beam pumping of the laser gas medium. Details of the design are based on a Monte-Carlo electron-beam deposition code, a one-dimensional, time-dependent kinetics code, and pulsed power circuit modeling. Linear dimensions of the amplifier's extracted gain volume are 6.25 m in height and length and 5.12 m in width. Each amplifier handles 160 angularly multiplexed laser channels. The one-amagat, krypton-rich laser medium is e-beam pumped at 60-kW cm/sup /minus/3/ (4-MA at3.3-MV) over the 2-microsecond duration of the laser beam pulse train. 5 refs., 4 figs

Diagnostic value of newborn foot length to predict gestational age

Directory of Open Access Journals (Sweden)

Mutia Farah Fawziah

2017-08-01

Full Text Available Background  Identification of gestational age, especially within 48 hours of birth, is crucial for newborns, as the earlier preterm status is detected, the earlier the child can receive optimal management. Newborn foot length is an anthropometric measurement which is easy to perform, inexpensive, and potentially efficient for predicting gestational age. Objective  To analyze the diagnostic value of newborn foot length in predicting gestational age. Methods  This diagnostic study was performed between October 2016 and February 2017 in the High Care Unit of Neonates at Dr. Moewardi General Hospital, Surakarta. A total of 152 newborns were consecutively selected and underwent right foot length measurements before 96 hours of age. The correlation between newborn foot length to classify as full term and gestational age was analyzed with Spearman’s correlation test because of non-normal data distribution. The cut-off point of newborn foot length was calculated by receiver operating characteristic (ROC curve and diagnostic values of newborn foot length were analyzed by 2 x 2 table with SPSS 21.0 software. Results There were no significant differences between male and female newborns in terms of gestational age, birth weight, choronological age, and newborn foot length (P>0.05. Newborn foot length and gestational age had a significant correlation (r=0.53; P=0.000. The optimal cut-off newborn foot length to predict full term status was 7.1 cm. Newborn foot length below 7.1 cm had sensitivity 75%, specificity 98%, positive predictive value 94.3%, negative predictive value 90.6%, positive likelihood ratio 40.5, negative likelihood ratio 0.25, and post-test probability 94.29%, to predict preterm status in newborns. Conclusion  Newborn foot length can be used to predict gestational age, especially for the purpose of differentiating between preterm and full term newborns.

Oriented particleboard made from tali bamboo (Gigantochloa Apus): effect of particle length on physical and mechanical properties

Science.gov (United States)

Iswanto, A. H.

2018-02-01

Strength properties are one of the problems of particleboard. The objective of this research was to analyze the effect of particle length on physical and mechanical properties oriented particleboard (OPB). The variation particle length size in this experiment namely 3, 5, and 7 cm. The width and thickness size of all bamboo particles were 1 and 0.1 cm respectively. 12% mixed resin of UF and MDI (70/30 %w/w) used for binding. Board size fabricated in 25 by 25 cm2 with thickness and density target of 1 cm and 0.75 gcm-3. The OPB layers for face and back layers aligned perpendicular to the core layer. The weight ratio of the face-to-core-to-back layers were set at 1:2:1. Mat was pressed at 160 °C under 30 kgcm-2 as the pressure for 10 minutes. The results showed that 7 cm length particle produced of the best strength and dimensional stability. The increase of particle length resulted in increasing of strength properties. Over all the parameters of physical and mechanical properties fulfill requirements of JIS A 5908 (2003) excepted of thickness swelling and modulus of elasticity.

Estimation of radioactive contaminants in Cm242 and Cm244 isotopic fuels

International Nuclear Information System (INIS)

Terent'ev, V.P.; Makarenko, A.I.

1972-01-01

The radiation properties of Cm 242 and Cm 244 preparations and the effect on them of possible contaminants are considered. One of the most important requirements for K alpha active fuels for radioisotope thermoelectric batteries is ensuring a low ionizing radiation background. In determining the effect of impurities on the radiation properties of a preparation, quantitative evaluation of certain factors is sufficient. In a Cm 242 preparation it is possible to show that Am 241 and Cm 243 are undesirable impurities. The presence of Am 241 increases the soft gamma output by 20%. The presence of Cm 243 may double the dose rate from an unshielded preparation and increase the hard gamma output 10-fold. The properties of Cm 242 preparations deteriorate when Am 243 and Cm 243 are present

Dorsal Phalloplasty to Preserve Penis Length after Penile Prosthesis Implantation

Directory of Open Access Journals (Sweden)

Osama Shaeer

2017-03-01

Full Text Available Objectives: Following penile prosthesis implantation (PPI, patients may complain of a decrease in visible penis length. A dorsal phalloplasty defines the penopubic junction by tacking pubic skin to the pubis, revealing the base of the penis. This study aimed to evaluate the efficacy of a dorsal phalloplasty in increasing the visible penis length following PPI. Methods: An inflatable penile prosthesis was implanted in 13 patients with severe erectile dysfunction (ED at the Kamal Shaeer Hospital, Cairo, Egypt, from January 2013 to May 2014. During the surgery, nonabsorbable tacking sutures were used to pin the pubic skin to the pubis through the same penoscrotal incision. Intraoperative penis length was measured before and after the dorsal phalloplasty. Overall patient satisfaction was measured on a 5-point rating scale and patients were requested to subjectively compare their postoperative penis length with memories of their penis length before the onset of ED. Results: Intraoperatively, the dorsal phalloplasty increased the visible length of the erect penis by an average of 25.6%. The average length before and after tacking was 10.2 ± 2.9 cm and 13.7 ± 2.8 cm, respectively (P <0.002. Postoperatively, seven patients (53.8% reported a longer penis, five patients (38.5% reported no change in length and one patient (7.7% reported a slightly shorter penis. The mean overall patient satisfaction score was 4.9 ± 0.3. None of the patients developed postoperative complications. Conclusion: A dorsal phalloplasty during PPI is an effective method of increasing visible penis length, therefore minimising the impression of a shorter penis after implantation.

Progress in Long Scale Length Laser-Plasma Interactions

International Nuclear Information System (INIS)

Glenzer, S H; Arnold, P; Bardsley, G; Berger, R L; Bonanno, G; Borger, T; Bower, D E; Bowers, M; Bryant, R; Buckman, S.; Burkhart, S C; Campbell, K; Chrisp, M P; Cohen, B I; Constantin, G; Cooper, F; Cox, J; Dewald, E; Divol, L; Dixit, S; Duncan, J; Eder, D; Edwards, J; Erbert, G; Felker, B; Fornes, J; Frieders, G; Froula, D H; Gardner, S D; Gates, C; Gonzalez, M; Grace, S; Gregori, G; Greenwood, A; Griffith, R; Hall, T; Hammel, B A; Haynam, C; Heestand, G; Henesian, M; Hermes, G; Hinkel, D; Holder, J; Holdner, F; Holtmeier, G; Hsing, W; Huber, S; James, T; Johnson, S; Jones, O S; Kalantar, D; Kamperschroer, J H; Kauffman, R; Kelleher, T; Knight, J; Kirkwood, R K; Kruer, W L; Labiak, W; Landen, O L; Langdon, A B; Langer, S; Latray, D; Lee, A; Lee, F D; Lund, D; MacGowan, B; Marshall, S; McBride, J; McCarville, T; McGrew, L; Mackinnon, A J; Mahavandi, S; Manes, K; Marshall, C; Mertens, E; Meezan, N; Miller, G; Montelongo, S; Moody, J D; Moses, E; Munro, D; Murray, J; Neumann, J; Newton, M; Ng, E; Niemann, C; Nikitin, A; Opsahl, P; Padilla, E; Parham, T; Parrish, G; Petty, C; Polk, M; Powell, C; Reinbachs, I; Rekow, V; Rinnert, R; Riordan, B; Rhodes, M.

2003-01-01

The first experiments on the National Ignition Facility (NIF) have employed the first four beams to measure propagation and laser backscattering losses in large ignition-size plasmas. Gas-filled targets between 2 mm and 7 mm length have been heated from one side by overlapping the focal spots of the four beams from one quad operated at 351 nm (3ω) with a total intensity of 2 x 10 15 W cm -2 . The targets were filled with 1 atm of CO 2 producing of up to 7 mm long homogeneously heated plasmas with densities of n e = 6 x 10 20 cm -3 and temperatures of T e = 2 keV. The high energy in a NIF quad of beams of 16kJ, illuminating the target from one direction, creates unique conditions for the study of laser plasma interactions at scale lengths not previously accessible. The propagation through the large-scale plasma was measured with a gated x-ray imager that was filtered for 3.5 keV x rays. These data indicate that the beams interact with the full length of this ignition-scale plasma during the last ∼1 ns of the experiment. During that time, the full aperture measurements of the stimulated Brillouin scattering and stimulated Raman scattering show scattering into the four focusing lenses of 6% for the smallest length (∼2 mm). increasing to 12% for ∼7 mm. These results demonstrate the NIF experimental capabilities and further provide a benchmark for three-dimensional modeling of the laser-plasma interactions at ignition-size scale lengths

The Length-Weight, Length-Length Relationship and Condition Factor of Angora Loach, Oxynoemacheilus angorae (Steindachner, 1897 Inhabiting Kılıçözü Stream in Kızılırmak River Basin (Central Anatolia-Turkey

Directory of Open Access Journals (Sweden)

Okan Yazıcıoğlu

2016-12-01

Full Text Available In this study, length-weight relationship (LWR, length- length relationship (LLR and condition factor (K of Angora loach, Oxynoemacheilus angorae were determined. A total of 103 specimens were sampled from Kılıçözü Stream in 2014. The length and weight of specimens were ranged 3.5-9.8 cm and 0.38-6.58 g, respectively. Length-weight relationships for female, male and all samples were found as W= 0.01056.TL2.896 (r²= 0.923, W= 0.00963.TL2.940 (r²= 0.978 and W= 0.00987.TL2.929 (r²= 0.963, respectively. LWRs indicated an isometric growth in female, male and all samples. The values of Fulton’s condition factor (K ranged from 0.699 to 1.246 for females and from 0.654 to 1.072 for males. All length-length relationships were statistically significant.

Sample-length dependence of the critical current of slightly and significantly bent-damaged Bi2223 superconducting composite tape

International Nuclear Information System (INIS)

Ochiai, S; Fujimoto, M; Okuda, H; Oh, S S; Ha, D W

2007-01-01

The local critical current along a sample length is different from position to position in a long sample, especially when the sample is damaged by externally applied strain. In the present work, we attempted to reveal the relation of the distribution of the local critical current to overall critical current and the sample-length dependence of critical current for slightly and significantly damaged Bi2223 composite tape samples. In the experiment, 48 cm long Bi2223 composite tape samples, composed of 48 local elements with a length of 1 cm and 8 parts with a length 6 cm, were bent by 0.37 and 1.0% to cause slight and significant damage, respectively. The V-I curve, critical current (1 μV cm -1 criterion) and n value were measured for the overall sample as well as for the local elements and parts. It was found that the critical current distributions of the 1 cm elements at 0.37 and 1.0% bending strains are described by the three-parameter- and bimodal Weibull distribution functions, respectively. The critical current of a long sample at both bending strains could be described well by substituting the distributed critical current and n value of the short elements into the series circuit model for voltage generation. Also the measured relation of average critical current to sample length could be reproduced well in the computer by a Monte Carlo simulation method. It was shown that the critical current and n value decrease with increasing sample length at both bending strains. The extent of the decrease in critical current with sample length is dependent on the criterion of the critical current; the critical current decreases only slightly under the 1 μV cm -1 criterion which is not damage-sensitive, while it decreases greatly with increasing sample length under damage-sensitive criteria such as the 1 μV one

A New Maximum Length Record of the Bluefish (Pomatomus saltatrix Linnaeus, 1766) for Turkey Seas

OpenAIRE

Cengiz, Özgür

2014-01-01

One specimen of the bluefish (Pomatomus saltatrix Linnaeus, 1766) with 76.5 cm in total length and 4800.0 g in total weight was photographed in the Çanakkale Fish Market. The given length is second maximum length record of the bluefish for Turkish waters

Limb lengthening in Africa: tibial lengthening indicated for limb length discrepancy and postosteomyelitis pseudarthrosis

Directory of Open Access Journals (Sweden)

Ibrahima F

2014-05-01

Full Text Available Farikou Ibrahima,1,2 Pius Fokam,2 Félicien Faustin Mouafo Tambo11Department of Surgery and Specialties, Faculty of Medicine and Biomedical Sciences, University of Yaoundé I, Yaoundé, 2Department of Surgery, Douala General Hospital, Douala, CameroonBackground: We present a case of lengthening of a tibia to treat postosteomyelitis pseudarthrosis and limb length discrepancy by the Ilizarov device.Objective: The objective was to treat the pseudarthrosis and correct the consequent limb length discrepancy of 50 mm.Materials and methods: The patient was a 5-year-old boy. Osteotomy of the tibia, excision of fibrosis, and decortications were carried out. After a latency period of 5 days, the lengthening started at a rate of 1 mm per day.Results: The pseudarthrosis healed and the gained correction was 21.73%. The index consolidation was 49 days/cm. Minor complications were reported.Discussion: Osteomyelitis of long bones is a common poverty-related disease in Africa. The disease usually is diagnosed at an advanced stage with complications. In these conditions, treatment is much more difficult. Most surgical procedures treating this condition use the Ilizarov device. The most common reported surgical complications are refractures and recurrence of infection.Conclusion: This technique should be popularized in countries with limited resources because it would be an attractive alternative to the amputations that are sometimes performed.Keywords: Limb length discrepancy (LLD, bone gap, Ilizarov device

Prenatal exposure to traffic pollution: associations with reduced fetal growth and rapid infant weight gain.

Science.gov (United States)

Fleisch, Abby F; Rifas-Shiman, Sheryl L; Koutrakis, Petros; Schwartz, Joel D; Kloog, Itai; Melly, Steven; Coull, Brent A; Zanobetti, Antonella; Gillman, Matthew W; Gold, Diane R; Oken, Emily

2015-01-01

Prenatal air pollution exposure inhibits fetal growth, but implications for postnatal growth are unknown. We assessed weights and lengths of US infants in the Project Viva cohort at birth and 6 months. We estimated 3rd-trimester residential air pollution exposures using spatiotemporal models. We estimated neighborhood traffic density and roadway proximity at birth address using geographic information systems. We performed linear and logistic regression adjusted for sociodemographic variables, fetal growth, and gestational age at birth. Mean birth weight-for-gestational age z-score (fetal growth) was 0.17 (standard deviation [SD] = 0.97; n = 2,114), 0- to 6-month weight-for-length gain was 0.23 z-units (SD = 1.11; n = 689), and 17% had weight-for-length ≥95th percentile at 6 months of age. Infants exposed to the highest (vs. lowest) quartile of neighborhood traffic density had lower fetal growth (-0.13 units [95% confidence interval (CI) = -0.25 to -0.01]), more rapid 0- to 6-month weight-for-length gain (0.25 units [95% CI = 0.01 to 0.49]), and higher odds of weight-for-length ≥95th percentile at 6 months (1.84 [95% CI = 1.11 to 3.05]). Neighborhood traffic density was additionally associated with an infant being in both the lowest quartile of fetal growth and the highest quartile of 0- to 6-month weight-for-length gain (Q4 vs. Q1, odds ratio = 3.01 [95% CI = 1.08 to 8.44]). Roadway proximity and 3rd-trimester black carbon exposure were similarly associated with growth outcomes. For 3rd-trimester particulate matter (PM2.5), effect estimates were in the same direction, but smaller and imprecise. Infants exposed to higher traffic-related pollution in early life may exhibit more rapid postnatal weight gain in addition to reduced fetal growth.

Minimal Length Scale Scenarios for Quantum Gravity.

Science.gov (United States)

Hossenfelder, Sabine

2013-01-01

We review the question of whether the fundamental laws of nature limit our ability to probe arbitrarily short distances. First, we examine what insights can be gained from thought experiments for probes of shortest distances, and summarize what can be learned from different approaches to a theory of quantum gravity. Then we discuss some models that have been developed to implement a minimal length scale in quantum mechanics and quantum field theory. These models have entered the literature as the generalized uncertainty principle or the modified dispersion relation, and have allowed the study of the effects of a minimal length scale in quantum mechanics, quantum electrodynamics, thermodynamics, black-hole physics and cosmology. Finally, we touch upon the question of ways to circumvent the manifestation of a minimal length scale in short-distance physics.

Radiation hardness of thin Low Gain Avalanche Detectors

Science.gov (United States)

Kramberger, G.; Carulla, M.; Cavallaro, E.; Cindro, V.; Flores, D.; Galloway, Z.; Grinstein, S.; Hidalgo, S.; Fadeyev, V.; Lange, J.; Mandić, I.; Medin, G.; Merlos, A.; McKinney-Martinez, F.; Mikuž, M.; Quirion, D.; Pellegrini, G.; Petek, M.; Sadrozinski, H. F.-W.; Seiden, A.; Zavrtanik, M.

2018-05-01

Low Gain Avalanche Detectors (LGAD) are based on a n++-p+-p-p++ structure where an appropriate doping of the multiplication layer (p+) leads to high enough electric fields for impact ionization. Gain factors of few tens in charge significantly improve the resolution of timing measurements, particularly for thin detectors, where the timing performance was shown to be limited by Landau fluctuations. The main obstacle for their operation is the decrease of gain with irradiation, attributed to effective acceptor removal in the gain layer. Sets of thin sensors were produced by two different producers on different substrates, with different gain layer doping profiles and thicknesses (45, 50 and 80 μm). Their performance in terms of gain/collected charge and leakage current was compared before and after irradiation with neutrons and pions up to the equivalent fluences of 5 ṡ 1015 cm-2. Transient Current Technique and charge collection measurements with LHC speed electronics were employed to characterize the detectors. The thin LGAD sensors were shown to perform much better than sensors of standard thickness (∼300 μm) and offer larger charge collection with respect to detectors without gain layer for fluences gain prolongs the beneficial performance of LGADs. Pions were found to be more damaging than neutrons at the same equivalent fluence, while no significant difference was found between different producers. At very high fluences and bias voltages the gain appears due to deep acceptors in the bulk, hence also in thin standard detectors.

Birth Weight, Postnatal Weight Gain, and Childhood Adiposity in Relation to Lipid Profile and Blood Pressure During Early Adolescence.

Science.gov (United States)

Hulst, Andraea Van; Barnett, Tracie A; Paradis, Gilles; Roy-Gagnon, Marie-Hélène; Gomez-Lopez, Lilianne; Henderson, Mélanie

2017-08-04

Different pathways likely underlie the association between early weight gain and cardiovascular disease risk. We examined whether birth weight for length relationship and weight gain up to 2 years of age are associated with lipid profiles and blood pressure (BP) in early adolescence and determined whether childhood adiposity mediates these associations. Data from QUALITY (Quebec Adipose and Lifestyle Investigation in Youth), a cohort of white children with parental history of obesity, were analyzed (n=395). Sex-specific weight for length z scores from birth to 2 years were computed. Rate of postnatal weight gain was estimated using individual slopes of weight for length z -score measurements. Percentage of body fat was measured at 8 to 10 years. Fasting lipids and BP were measured at 10 to 12 years. Using path analysis, we found indirect effects of postnatal weight gain, through childhood adiposity, on all outcomes: Rate of postnatal weight for length gain was positively associated with childhood adiposity, which in turn was associated with unfavorable lipid and BP levels in early adolescence. In contrast, small beneficial direct effects on diastolic BP z scores, independent of weight at other time points, were found for birth weight for length (β=-0.05, 95% CI, -0.09 to -0.002) and for postnatal weight gain (β=-0.02, 95% CI, -0.03 to -0.002). Among children with at least 1 obese parent, faster postnatal weight gain leads to cardiovascular risk factors in early adolescence through its effect on childhood adiposity. Although heavier newborns may have lower BP in early adolescence, this protective direct effect could be offset by a deleterious indirect effect linking birth weight to later adiposity. © 2017 The Authors. Published on behalf of the American Heart Association, Inc., by Wiley.

Assessment of colorectal length using the electromagnetic capsule tracking system: a comparative validation study in healthy subjects.

Science.gov (United States)

Mark, E B; Poulsen, J L; Haase, A M; Frøkjaer, J B; Schlageter, V; Scott, S M; Krogh, K; Drewes, A M

2017-09-01

We aimed to determine colorectal length with the 3D-Transit system by describing a 'centreline' of capsule movement and comparing it with known anatomy, as determined by magnetic resonance imaging (MRI). Further, we aimed to test the day-to-day variation of colorectal length assessed with the system. The 3D-Transit system consists of electromagnetic capsules that can be tracked as they traverse the gastrointestinal tract. Twenty-five healthy subjects were examined with both 3D-Transit and MRI. Another 21 healthy subjects were examined with 3D-Transit on two consecutive days. Computation of colorectal length from capsule passage was possible for 60 of the 67 3D-Transit recordings. The length of the colorectum measured with MRI and 3D-Transit was 95 (75-153) cm and 99 (77-147) cm, respectively (P = 0.15). The coefficient of variation (CV) between MRI and 3D-Transit was 7.8%. Apart from the caecum/ascending colon being 26% (P = 0.002) shorter on MRI, there were no other differences in total or segmental colorectal lengths between methods (all P > 0.05). The length of the colorectum measured with 3D-Transit on two consecutive days was 102 (73-119) cm and 103 (75-123) cm (P = 0.67). The CV between days was 7.3%. The 3D-Transit system allows accurate and reliable determination of colorectal length compared with MRI-derived colorectal length and between days. Antegrade or retrograde capsule movement relative to this centreline, as well as the length and speed of movements, may be determined by future studies to allow better classification and treatment in patients with dysmotility. Colorectal Disease © 2017 The Association of Coloproctology of Great Britain and Ireland.

Amplified spontaneous emissions in a high-gain laser amplifier

International Nuclear Information System (INIS)

Osada, Hidenori; Gamo, Hideya.

1978-01-01

The gain and line-narrowing of the amplified spontaneous emissions(ASE) in a partially homogeneous high-gain Xe 3.51 μm laser amplifier were studied theoretically and experimentally with emphasis of saturation effect. The unidirectionally travelling ASE was generated by conveniently using optical isolators and used as a broadband radiation source. It has properties of 10 μW/mm 2 in intensity with fluctuation of less than 1% in 5 hours, 43.5 MHz of the linewidth and 1.0 x 10 -3 radians of beam divergence. The measured saturation intensity was 4.85 μW/mm 2 and a small signal gain was 0.1 cm -1 . The theoretical prediction of the line-narrowing shows reasonablly good agreement with the measured one. (author)

Direct ink write fabrication of transparent ceramic gain media

Science.gov (United States)

Jones, Ivy Krystal; Seeley, Zachary M.; Cherepy, Nerine J.; Duoss, Eric B.; Payne, Stephen A.

2018-01-01

Solid-state laser gain media based on the garnet structure with two spatially distinct but optically contiguous regions have been fabricated. Transparent gain media comprised of a central core of Y2.97Nd0.03Al5.00O12.00 (Nd:YAG) and an undoped cladding region of Y3Al5O12 (YAG) were fabricated by direct ink write and transparent ceramic processing. Direct ink write (DIW) was employed to form the green body, offering a general route to preparing functionally structured solid-state laser gain media. Fully-dense transparent optical ceramics in a "top hat" geometry with YAG/Nd:YAG have been fabricated by DIW methods with optical scatter at 1064 nm of <3%/cm.

CORRELATION BETWEEN PENIS LENGTH AND ANTHOPOMETRY OF 5 YEAR OLD CHILDREN

Directory of Open Access Journals (Sweden)

Doddy Kurnia Indrawan

2013-03-01

Full Text Available Short penis still a problem for parents. Penis lenght is associated with  weight and considered abnormal in obese children. The purpose of this study was to find out the correlation between penis length and the anthropometry children aged 5 years. A cross sectional study was conducted, at the Division of Endocrinology, Department of Child Health, Medical Faculty of Udayana University, Sanglah Hospital Denpasar, during October 2010, at TK Sayang Ibu Sanglah Hospital. The calculation of the sample with a correlation coefficient of weight and  height obtained  9 people, taking in consecutive sampling and analyzed  with Pearson’s correlation. The mean body weight was 23.6 (SD 7.70 kg;  mean child height was 108.4 (SD 5.3 cm, and 47.1% were obese. The mean length of the penis was 4.7(SD1.30 cm. The correlation between weight and penis lenght was strong negative (r = -0.876; P = 0.000 and between penis length and height was r = -0.597; P = 0,011.There was a strong negative correlation between body weight and penis length and also negative correlation between penis length and height in kindergarten children. (MEDICINA 2012;43:19-22.

A methodology for direct quantification of over-ranging length in helical computed tomography with real-time dosimetry.

Science.gov (United States)

Tien, Christopher J; Winslow, James F; Hintenlang, David E

2011-01-31

In helical computed tomography (CT), reconstruction information from volumes adjacent to the clinical volume of interest (VOI) is required for proper reconstruction. Previous studies have relied upon either operator console readings or indirect extrapolation of measurements in order to determine the over-ranging length of a scan. This paper presents a methodology for the direct quantification of over-ranging dose contributions using real-time dosimetry. A Siemens SOMATOM Sensation 16 multislice helical CT scanner is used with a novel real-time "point" fiber-optic dosimeter system with 10 ms temporal resolution to measure over-ranging length, which is also expressed in dose-length-product (DLP). Film was used to benchmark the exact length of over-ranging. Over-ranging length varied from 4.38 cm at pitch of 0.5 to 6.72 cm at a pitch of 1.5, which corresponds to DLP of 131 to 202 mGy-cm. The dose-extrapolation method of Van der Molen et al. yielded results within 3%, while the console reading method of Tzedakis et al. yielded consistently larger over-ranging lengths. From film measurements, it was determined that Tzedakis et al. overestimated over-ranging lengths by one-half of beam collimation width. Over-ranging length measured as a function of reconstruction slice thicknesses produced two linear regions similar to previous publications. Over-ranging is quantified with both absolute length and DLP, which contributes about 60 mGy-cm or about 10% of DLP for a routine abdominal scan. This paper presents a direct physical measurement of over-ranging length within 10% of previous methodologies. Current uncertainties are less than 1%, in comparison with 5% in other methodologies. Clinical implantation can be increased by using only one dosimeter if codependence with console readings is acceptable, with an uncertainty of 1.1% This methodology will be applied to different vendors, models, and postprocessing methods--which have been shown to produce over-ranging lengths

HD CAG-correlated gene expression changes support a simple dominant gain of function

Science.gov (United States)

Jacobsen, Jessie C.; Gregory, Gillian C.; Woda, Juliana M.; Thompson, Morgan N.; Coser, Kathryn R.; Murthy, Vidya; Kohane, Isaac S.; Gusella, James F.; Seong, Ihn Sik; MacDonald, Marcy E.; Shioda, Toshi; Lee, Jong-Min

2011-01-01

Huntington's disease is initiated by the expression of a CAG repeat-encoded polyglutamine region in full-length huntingtin, with dominant effects that vary continuously with CAG size. The mechanism could involve a simple gain of function or a more complex gain of function coupled to a loss of function (e.g. dominant negative-graded loss of function). To distinguish these alternatives, we compared genome-wide gene expression changes correlated with CAG size across an allelic series of heterozygous CAG knock-in mouse embryonic stem (ES) cell lines (HdhQ20/7, HdhQ50/7, HdhQ91/7, HdhQ111/7), to genes differentially expressed between Hdhex4/5/ex4/5 huntingtin null and wild-type (HdhQ7/7) parental ES cells. The set of 73 genes whose expression varied continuously with CAG length had minimal overlap with the 754-member huntingtin-null gene set but the two were not completely unconnected. Rather, the 172 CAG length-correlated pathways and 238 huntingtin-null significant pathways clustered into 13 shared categories at the network level. A closer examination of the energy metabolism and the lipid/sterol/lipoprotein metabolism categories revealed that CAG length-correlated genes and huntingtin-null-altered genes either were different members of the same pathways or were in unique, but interconnected pathways. Thus, varying the polyglutamine size in full-length huntingtin produced gene expression changes that were distinct from, but related to, the effects of lack of huntingtin. These findings support a simple gain-of-function mechanism acting through a property of the full-length huntingtin protein and point to CAG-correlative approaches to discover its effects. Moreover, for therapeutic strategies based on huntingtin suppression, our data highlight processes that may be more sensitive to the disease trigger than to decreased huntingtin levels. PMID:21536587

Postnatal penile length and growth rate correlate to serum testosterone levels

DEFF Research Database (Denmark)

Boas, Malene; Boisen, Kirsten A; Virtanen, Helena E

2006-01-01

in Denmark and at 0, 3 and 18 months in Finland with blood samples taken at 3 months (n = 630). Penile length and growth were registered and reproductive hormones (testosterone, sex hormone binding globulin, oestradiol) were analysed. RESULTS: Penile length increased from birth (3.49+/-0.4 cm) to 3 years...... and growth. DESIGN: Prospective, longitudinal population-based study taking place at two large primary obstetric centres at the University Hospitals of Copenhagen, Denmark, and Turku, Finland. METHODS: Infant boys, 728 Danish and 1234 Finnish, underwent clinical examinations at 0, 3, 18 and 36 months...... of age (4.53+/-0.51 cm) with the highest growth velocity from birth to 3 months (1.0 mm/month). Penile length and growth were significantly, positively correlated to serum testosterone (r = 0.31 and 0.076, P = 0.006 and 0.001 respectively) and to free testosterone index (r = 0.385 and 0.094, P = 0...

Evaluation of neutron cross sections for 244Cm, 246Cm, and 248Cm

International Nuclear Information System (INIS)

Benjamin, R.W.; McCrosson, F.J.; Gettys, W.E.

1977-01-01

An evaluation of neutron cross sections for 244 246 248 Cm using the ENDF/B format is presented. Primary data input included differential measurements, integral measurements, nuclear model calculations, and reactor production experience

Minimal Length Scale Scenarios for Quantum Gravity

Directory of Open Access Journals (Sweden)

Sabine Hossenfelder

2013-01-01

Full Text Available We review the question of whether the fundamental laws of nature limit our ability to probe arbitrarily short distances. First, we examine what insights can be gained from thought experiments for probes of shortest distances, and summarize what can be learned from different approaches to a theory of quantum gravity. Then we discuss some models that have been developed to implement a minimal length scale in quantum mechanics and quantum field theory. These models have entered the literature as the generalized uncertainty principle or the modified dispersion relation, and have allowed the study of the effects of a minimal length scale in quantum mechanics, quantum electrodynamics, thermodynamics, black-hole physics and cosmology. Finally, we touch upon the question of ways to circumvent the manifestation of a minimal length scale in short-distance physics.

Inelastic analysis of finite length and depth cracked tubes

International Nuclear Information System (INIS)

Reich, M.; Prachuktam, S.; Gardner, D.

1977-01-01

Steam generator tube failure can at times result in reactor safety problems and subsequent premature reactor shutdowns. Typical PWR steam generator units contain thousands of long straight tubes with U-bend sections. These tubes are primarily made from alloy 600 and their sizes vary between 3 / 4 '' and 7 / 8 '' (1.905 cm and 2.223 cm) in diameter with nominal thicknesses of 0.043'' to 0.053'' (0.109 cm to 0.135 cm). Since alloy 600 (and the previously used 304-SS tubes) are ductile, high toughness materials LEFM (linear elastic fracture mechanics) criteria do not apply. This paper concerns itself with the prediction of the failure pressures for typical PWR steam generator tubes with longitudinal finite length and finite depth cracks. Only local plastic overload failure is considered

243Cm half-life determinaton

International Nuclear Information System (INIS)

Timofeev, G.A.; Kalygin, V.V.; Privalova, P.A.

1986-01-01

By molar ratios of 243 Cm mixture with 244 Cm and Pu nuclides formed as a result of Cm nuclides α-decay the 243 Cm half-life T α243 is determined. The 244 Cm half-life is measured earlier with high accuracy. The 243 Cm/ 244 Cm ratio measured by means of a mass spectrometer equals 0.989+-0.004. The obtained value T α243 =29.20+-0.14 years

Kidney Length in Normal Korean Children

International Nuclear Information System (INIS)

Kim, In One; Cheon, Jung Eun; Lee, Young Seok; Lee, Sun Wha; Kim, Ok Hwa; Kim, Ji Hye; Kim, Hong Dae; Sim, Jung Suk

2010-01-01

Renal length offers important information to detect or follow-up various renal diseases. The purpose of this study was to determine the kidney length of normal Korean children in relation to age, height, weight, body surface area (BSA), and body mass index (BMI). Children between 1 month and 15 years of age without urological abnormality were recruited. Children below 3rd percentile and over 97th percentile for height or weight were excluded. Both renal lengths were measured in the prone position three times and then averaged by experienced radiologists. The mean length and standard deviation for each age group was obtained, and regression equation was calculated between renal length and age, weight, height, BSA, and BMI, respectively. Renal length was measured in 550 children. Renal length grows rapidly until 24 month, while the growth rate is reduced thereafter. The regression equation for age is: renal length (mm) = 45.953 + 1.064 x age (month, ≤ 24 months) (R2 = 0.720) or 62.173 + 0.203 x age (months, > 24 months) (R2 = 0.711). The regression equation for height is: renal length (mm) = 24.494 + 0.457 x height (cm) (R2 = 0.894). The regression equation for weight is: renal length (mm) = 38.342 + 2.117 x weight (kg, ≤18 kg) (R2 = 0.852) or 64.498 + 0.646 x weight (kg, > 18 kg) (R2 = 0.651). The regression equation for BSA is: renal length (mm) = 31.622 + 61.363 x BSA (m2, ≤ 0.7) (R2 = 0.857) or 52.717 + 29.959 x BSA (m2, > 0.7) (R2 = 0.715). The regression equation for BMI is: renal length (mm) = 44.474 + 1.163 x BMI (R2 = 0.079). This study provides data on the normal renal length and its association with age, weight, height, BSA and BMI. The results of this study will guide the detection and follow-up of renal diseases in Korean children

Maternal height and length of gestation: does this impact on preterm labour in Asian women?

Science.gov (United States)

Chan, Ben Chong-Pun; Lao, Terence Tzu-Hsi

2009-08-01

Both maternal height and ethnicity may influence the gestation length, but their independent effect is unclear. This study was performed to examine the relationship between maternal height and gestational length in women with singleton pregnancies in a Chinese and southeast Asian population. A retrospective cohort study was performed on women carrying singleton pregnancies with spontaneous labour in a 48-month period managed under our department to determine the relationship between maternal height, expressed in quartiles, with the mean gestational age and incidence of preterm labour. Of the 16 384 women who delivered within this period, the 25th, 50th and 75th percentile values of maternal height were 153 cm, 156 cm and 160 cm respectively. Excluded from analysis were 6597 women because of multifetal pregnancy, teenage pregnancy (maternal age women with shorter stature. In our population, maternal height has an influence on gestational length, and the lower three quartiles was associated with increased odds of labour at > 32 to management and intervention.

Length and volume of morphologically normal kidneys in Korean Children: Ultrasound measurement and estimation using body size

International Nuclear Information System (INIS)

Kim, Jun Hwee; Kim, Myung Joon; Lim, Sok Hwan; Lee, Mi Jung; Kim, Ji Eun

2013-01-01

To evaluate the relationship between anthropometric measurements and renal length and volume measured with ultrasound in Korean children who have morphologically normal kidneys, and to create simple equations to estimate the renal sizes using the anthropometric measurements. We examined 794 Korean children under 18 years of age including a total of 394 boys and 400 girls without renal problems. The maximum renal length (L) (cm), orthogonal anterior-posterior diameter (D) (cm) and width (W) (cm) of each kidney were measured on ultrasound. Kidney volume was calculated as 0.523 x L x D x W (cm 3 ). Anthropometric indices including height (cm), weight (kg) and body mass index (m 2 /kg) were collected through a medical record review. We used linear regression analysis to create simple equations to estimate the renal length and the volume with those anthropometric indices that were mostly correlated with the US-measured renal sizes. Renal length showed the strongest significant correlation with patient height (R2, 0.874 and 0.875 for the right and left kidneys, respectively, p < 0.001). Renal volume showed the strongest significant correlation with patient weight (R2, 0.842 and 0.854 for the right and left kidneys, respectively, p < 0.001). The following equations were developed to describe these relationships with an estimated 95% range of renal length and volume (R2, 0.826-0.884, p < 0.001): renal length = 2.383 + 0.045 x Height (± 1.135) and = 2.374 + 0.047 x Height (± 1.173) for the right and left kidneys, respectively; and renal volume 7.941 + 1.246 x Weight (± 15.920) and = 7.303 + 1.532 x Weight (± 18.704) for the right and left kidneys, respectively. Scatter plots between height and renal length and between weight and renal volume have been established from Korean children and simple equations between them have been developed for use in clinical practice.

Length and volume of morphologically normal kidneys in Korean Children: Ultrasound measurement and estimation using body size

Energy Technology Data Exchange (ETDEWEB)

Kim, Jun Hwee; Kim, Myung Joon; Lim, Sok Hwan; Lee, Mi Jung [Dept. of Radiology and Research Institute of Radiological Science, Severance Children' s Hospital, Yonsei University College of Medicine, Seoul (Korea, Republic of); Kim, Ji Eun [Biostatistics Collaboration Unit, Yonsei University College of Medicine, Seoul (Korea, Republic of)

2013-08-15

To evaluate the relationship between anthropometric measurements and renal length and volume measured with ultrasound in Korean children who have morphologically normal kidneys, and to create simple equations to estimate the renal sizes using the anthropometric measurements. We examined 794 Korean children under 18 years of age including a total of 394 boys and 400 girls without renal problems. The maximum renal length (L) (cm), orthogonal anterior-posterior diameter (D) (cm) and width (W) (cm) of each kidney were measured on ultrasound. Kidney volume was calculated as 0.523 x L x D x W (cm{sup 3}). Anthropometric indices including height (cm), weight (kg) and body mass index (m{sup 2}/kg) were collected through a medical record review. We used linear regression analysis to create simple equations to estimate the renal length and the volume with those anthropometric indices that were mostly correlated with the US-measured renal sizes. Renal length showed the strongest significant correlation with patient height (R2, 0.874 and 0.875 for the right and left kidneys, respectively, p < 0.001). Renal volume showed the strongest significant correlation with patient weight (R2, 0.842 and 0.854 for the right and left kidneys, respectively, p < 0.001). The following equations were developed to describe these relationships with an estimated 95% range of renal length and volume (R2, 0.826-0.884, p < 0.001): renal length = 2.383 + 0.045 x Height (± 1.135) and = 2.374 + 0.047 x Height (± 1.173) for the right and left kidneys, respectively; and renal volume 7.941 + 1.246 x Weight (± 15.920) and = 7.303 + 1.532 x Weight (± 18.704) for the right and left kidneys, respectively. Scatter plots between height and renal length and between weight and renal volume have been established from Korean children and simple equations between them have been developed for use in clinical practice.

Experimental investigation of cooling perimeter and disturbance length effect on stability of Nb3Sn cable-in-conduit conductors

International Nuclear Information System (INIS)

Armstrong, J.R.

1992-02-01

The stability of three coils, with similar parameters besides having differing strand diameters, was investigated experimentally using inductive heaters to input disturbances. One of the coils stability was also tested by doubling the inductive heated disturbance length to 10 cm. By computationally deriving approximate inductive heater input energy at 12 T, stability curves show fair agreement with zero-dimensional and one-dimensional computer predictions. Quench velocity and limiting currents also show good agreement with earlier work. Also, the stability measured on one of the coils below its limiting current by disturbing a 10 cm length of conductor was much less than the same samples stability using a 5 cm disturbance length. (author)

A simple method for estimating the length density of convoluted tubular systems.

Science.gov (United States)

Ferraz de Carvalho, Cláudio A; de Campos Boldrini, Silvia; Nishimaru, Flávio; Liberti, Edson A

2008-10-01

We present a new method for estimating the length density (Lv) of convoluted tubular structures exhibiting an isotropic distribution. Although the traditional equation Lv=2Q/A is used, the parameter Q is obtained by considering the collective perimeters of tubular sections. This measurement is converted to a standard model of the structure, assuming that all cross-sections are approximately circular and have an average perimeter similar to that of actual circular cross-sections observed in the same material. The accuracy of this method was tested in eight experiments using hollow macaroni bent into helical shapes. After measuring the length of the macaroni segments, they were boiled and randomly packed into cylindrical volumes along with an aqueous suspension of gelatin and India ink. The solidified blocks were cut into slices 1.0 cm thick and 33.2 cm2 in area (A). The total perimeter of the macaroni cross-sections so revealed was stereologically estimated using a test system of straight parallel lines. Given Lv and the reference volume, the total length of macaroni in each section could be estimated. Additional corrections were made for the changes induced by boiling, and the off-axis position of the thread used to measure length. No statistical difference was observed between the corrected estimated values and the actual lengths. This technique is useful for estimating the length of capillaries, renal tubules, and seminiferous tubules.

Is increased residual shank length a competitive advantage for elite transtibial amputee long jumpers?

Science.gov (United States)

Nolan, Lee; Patritti, Benjamin L; Stana, Laura; Tweedy, Sean M

2011-07-01

The purpose of this study was to evaluate the extent to which residual shank length affects long jump performance of elite athletes with a unilateral transtibial amputation. Sixteen elite, male, long jumpers with a transtibial amputation were videoed while competing in major championships (World Championships 1998, 2002 and Paralympic Games, 2004). The approach, take-off, and landing of each athlete's best jump was digitized to determine residual and intact shank lengths, jump distance, and horizontal and vertical velocity of center of mass at touchdown. Residual shank length ranged from 15 cm to 38 cm. There were weak, nonsignificant relationships between residual shank length and (a) distance jumped (r = 0.30), (b) horizontal velocity (r = 0.31), and vertical velocity (r = 0.05). Based on these results, residual shank length is not an important determinant of long jump performance, and it is therefore appropriate that all long jumpers with transtibial amputation compete in the same class. The relationship between residual shank length and key performance variables was stronger among athletes that jumped off their prosthetic leg (N = 5), and although this result must be interpreted cautiously, it indicates the need for further research.

Optical gain in GaAsBi-based quantum-well diode lasers (Conference Presentation)

Science.gov (United States)

Marko, Igor P.; Broderick, Christopher A.; Jin, Shirong; Ludewig, Peter; Stolz, Wolfgang; Volz, Kerstin; Rorison, Judy M.; O'Reilly, Eoin P.; Sweeney, Stephen J.

2017-02-01

GaAsBi offers the possibility to develop near-IR semiconductor lasers such that the spin-orbit-split-off energy (ΔSO) is greater than the bandgap (Eg) in the active region with lasing wavelengths in the datacom/telecom range of 1.3-1.6 μm. This promises to suppress the dominant efficiency-limiting loss processes as Auger recombination, involving the generation of "hot" holes in the spin-orbit split-off band (the so-called "CHSH" process), and inter-valence band absorption (IVBA), where emitted photons are re-absorbed in the active region, thereby increasing the internal optical losses and negatively impacting upon the laser characteristics being responsible for the main energy consumption. In addition to growth and fabrication processes refinement, a key aspect of efforts to continue the advancement of the GaAsBi material system for laser applications is to develop a quantitative understanding of the impact of Bi on key device parameters. In this work, we present the first experimental measurements of the absorption, spontaneous emission, and optical gain spectra of GaAsBi/AlGaAs QW lasers using a segmented contact method and a theoretical analysis of these devices, which shows good quantitative agreement with the experiment. Internal optical losses of 10-15 cm-1 and peak modal gain of 24 cm-1 are measured at threshold and a peak material gain is estimated to be 1500 cm-1 at current density of 2 kA/cm-2, which agrees well with the calculated value of 1560 cm-1. The theoretical calculations also enabled us to identify and quantify Bi composition variations across the wafer and Bi-induced inhomogeneous broadening of the optical spectra.

Erect penile length and circumference dimensions of 1,661 sexually active men in the United States.

Science.gov (United States)

Herbenick, Debby; Reece, Michael; Schick, Vanessa; Sanders, Stephanie A

2014-01-01

Penile size continues to receive popular and empirical attention. Little is known about the process of self-measurement and whether the behaviors a man engages in to become erect for self-measurement are associated with his erect penile dimensions. The article aims to assess men's erect penile dimensions in a study in which the men would presumably be motivated to report accurate information about their penis size; and to explore associations between men's erect penile dimensions, their method of measurement, and their demographics. Data are from an Internet-based baseline phase of a large prospective daily diary study that compared men's use of a standard-sized condom to men's use of a condom sized to fit their erect penis. The main outcomes are participant characteristics, activities engaged in during self-measurement process, and self-reported erect penile length and circumference. For this sample of 1,661 men, the mean erect penile length was 14.15 cm (SD = 2.66; range = 4 to 26 cm), and the mean erect penile circumference was 12.23 cm (SD = 2.23; range = 3 to 19). Participant characteristics were not associated with measured length or circumference. Most men measured their penis while alone, using hand stimulation to become erect. In this sample of men who measured their erect penile length and circumference for the purposes of receiving a condom sized to fit their erect penis, we found a mean erect penile length of 14.15 cm and a mean erect penile circumference of 12.23 cm. The self-reported erect penile dimensions in this study are consistent with other penile dimension research. Also, findings suggest that mode of getting an erection may influence erect penile dimensions. Additionally, how a man becomes erect for self-measurement may be associated with his erect penile length and/or circumference. © 2013 International Society for Sexual Medicine.

Gain characteristics of a multiatmosphere uv-preionized CO2 laser

International Nuclear Information System (INIS)

Alcock, A.J.; Fedosejevs, R.; Walker, A.C.

1975-01-01

The small-signal gain of a transverse-discharge UV-preionized CO 2 laser was investigated at pressures in the 1 to 15-atm range. Measurements were carried out on the P(18) and R(16) lines of both the 10.4- and 9.4-μm bands, and data on the pressure dependence of the peak gain and gain rise time are presented. The results demonstrate that small-signal gains in excess of 5-percent cm -1 are readily obtained at pressures of approximately 12 atm and confirm that the relaxation times of the energy levels relevant to laser action scale inversely with pressure. In addition, it is found that the gain of both R branches increases more rapidly with pressure than that of the P branches, while there are indications that the 9.4- and 10.4-μm gain values become comparable at pressures of approximately 15 atm. The experimental results are compared with the dependence of gain on pressure predicted by a relatively simple theoretical model. On the basis of this model it is found that the experimentally determined gain rises more rapidly with pressure than one would expect and a number of possible reasons for this discrepancy are discussed

Magnetic alloy nanowire arrays with different lengths: Insights into the crossover angle of magnetization reversal process

Energy Technology Data Exchange (ETDEWEB)

Samanifar, S.; Alikhani, M. [Department of Physics, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of); Almasi Kashi, M., E-mail: almac@kashanu.ac.ir [Department of Physics, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of); Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of); Ramazani, A. [Department of Physics, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of); Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of); Montazer, A.H. [Institute of Nanoscience and Nanotechnology, University of Kashan, Kashan 87317-51167 (Iran, Islamic Republic of)

2017-05-15

Nanoscale magnetic alloy wires are being actively investigated, providing fundamental insights into tuning properties in magnetic data storage and processing technologies. However, previous studies give trivial information about the crossover angle of magnetization reversal process in alloy nanowires (NWs). Here, magnetic alloy NW arrays with different compositions, composed of Fe, Co and Ni have been electrochemically deposited into hard-anodic aluminum oxide templates with a pore diameter of approximately 150 nm. Under optimized conditions of alumina barrier layer and deposition bath concentrations, the resulting alloy NWs with aspect ratio and saturation magnetization (M{sub s}) up to 550 and 1900 emu cm{sup −3}, respectively, are systematically investigated in terms of composition, crystalline structure and magnetic properties. Using angular dependence of coercivity extracted from hysteresis loops, the reversal processes are evaluated, indicating non-monotonic behavior. The crossover angle (θ{sub c}) is found to depend on NW length and M{sub s}. At a constant M{sub s}, increasing NW length decreases θ{sub c}, thereby decreasing the involvement of vortex mode during the magnetization reversal process. On the other hand, decreasing M{sub s} decreases θ{sub c} in large aspect ratio (>300) alloy NWs. Phenomenologically, it is newly found that increasing Ni content in the composition decreases θ{sub c}. The angular first-order reversal curve (AFORC) measurements including the irreversibility of magnetization are also investigated to gain a more detailed insight into θ{sub c}. - Highlights: • Magnetic alloy NWs with aspect ratios up to 550 were fabricated into hard-AAO templates. • Morphology, composition, crystal structure and magnetic properties were investigated. • Angular dependence of coercivity was used to describe the magnetization reversal process. • The crossover angle of magnetization reversal was found to depend on NW length and M{sub s}. �

Neutron spectra of /sup 242/Cm-Be and /sup 244/Cm-Be neutron sources

Energy Technology Data Exchange (ETDEWEB)

Kumar, A; Nagarajan, P S [Bhabha Atomic Research Centre, Bombay (India). Div. of Radiation Protection

1977-02-15

Neutron spectra of /sup 242/Cm-Be(..cap alpha..,n) and /sup 244/Cm-Be(..cap alpha..,n) sources have been calculated including the spontaneous fission contribution which is negligible for /sup 242/Cm and amounts to about 4% for /sup 244/Cm. The agreement of the present work with experimental results is poor.

Determination of carrier diffusion length in GaN

Science.gov (United States)

Hafiz, Shopan; Zhang, Fan; Monavarian, Morteza; Avrutin, Vitaliy; Morkoç, Hadis; Özgür, Ümit; Metzner, Sebastian; Bertram, Frank; Christen, Jürgen; Gil, Bernard

2015-01-01

Diffusion lengths of photo-excited carriers along the c-direction were determined from photoluminescence (PL) and cross-sectional cathodoluminescence (CL) measurements in p- and n-type GaN epitaxial layers grown on c-plane sapphire by metal-organic chemical vapor deposition. The investigated samples incorporate a 6 nm thick In0.15Ga0.85N active layer capped with either 500 nm p-GaN or 1500 nm n-GaN. The top GaN layers were etched in steps and PL from the InGaN active region and the underlying layers was monitored as a function of the top GaN thickness upon photo-generation near the surface region by above bandgap excitation. Taking into consideration the absorption in the top GaN layer as well as active and underlying layers, the diffusion lengths at 295 K and at 15 K were measured to be 93 ± 7 nm and 70 ± 7 nm for Mg-doped p-type GaN and 432 ± 30 nm and 316 ± 30 nm for unintentionally doped n-type GaN, respectively, at photogenerated carrier densities of 4.2 × 1018 cm-3 using PL spectroscopy. CL measurements of the unintentionally doped n-type GaN layer at much lower carrier densities of 1017 cm-3 revealed a longer diffusion length of 525 ± 11 nm at 6 K.

Pulsed WIP electron gun. Final report: design phase 1 x 70 cm cooled WIP electron gun, 1 December 1978--2 February 1979

International Nuclear Information System (INIS)

Wakalopulos, G.; Gresko, L.

1979-01-01

Presented here are design criteria for a full scale (70 cm) WIP electron gun system capable of long run operation with the following specifications: foil area approx. 70 x 1 cm, electron beam current density approx. 1 A/cm 2 , pulse length 2 , voltage -150 kV, voltage droop < 10%, Rep rate approx. 10 KHz, power approx. 20 kW, run time approx. 30 min, and jitter approx. 10 μs

Cervical Length in Patients at Risk for Placenta Accreta.

Science.gov (United States)

Rac, Martha W F; McIntire, Donald D; Wells, C Edward; Moschos, Elysia; Twickler, Diane D

2017-07-01

To evaluate cervical length measurements in women with placenta accreta compared to women with a nonadherent low-lying placenta or placenta previa and evaluate this relationship in terms of vaginal bleeding, preterm labor, and preterm birth. We conducted a retrospective cohort study between 1997 and 2011 of gravidas with more than 1 prior cesarean delivery who had a transvaginal ultrasound examination between 24 and 34 weeks for a low-lying placenta or placenta previa. Cervical length was measured from archived images in accordance with national guidelines by a single investigator, who was blinded to outcomes and ultrasound reports. The diagnosis of placental accreta was based on histologic confirmation. For study purposes, preterm birth was defined as less than 36 weeks, and cervical lengths of 3 cm or less were considered short. Standard statistical analyses were used. A total of 125 patients met inclusion criteria. The cohort was divided into patients with (n = 43 [34%]) and without (n = 82 [66%]) placenta accreta and stratified by gestational age at the ultrasound examinations. Women with placenta accreta had shorter cervical length measurements during their 32- to 34-week ultrasound examinations (mean ± SD, 3.23 ± 0.98 versus 3.95 ± 1.0 cm; P accreta had shorter cervical lengths at 32 to 34 weeks than women with a nonadherent low-lying placenta or placenta previa, but this finding did not correlate with a higher risk of vaginal bleeding or preterm labor resulting in preterm birth before 36 weeks. © 2017 by the American Institute of Ultrasound in Medicine.

Gain measurements at 182 /angstrom/ in C VI generated by a Nd/glass laser

International Nuclear Information System (INIS)

Kim, D.; Skinner, C.H.; Umesh, G.; Suckewer, S.

1988-11-01

We present recent gain measurements in C VI at 182 A for a soft x-ray amplifier produced by a line-focused glass laser(1.053 μm) on a solid carbon target. The maximum gain measured was 8 +- 1 cm/sup /minus/1/ in the recombining plasma column with additional radiation cooling by iron impurities. 10 refs., 3 figs

Theoretical designs of 19.6 nm Ne-like Ge XRL source

International Nuclear Information System (INIS)

Zhang Guoping; Zhang Tanxin; Zheng Wudi

2004-01-01

19.6 nm Ne-like Ge X-ray laser (XRL) can be used as a source to diagnose Rayleigh-Taylor instability in laser induced plasma. In this paper, systemic optimum designs and theoretical analysis to Ne-like Ge XRL driven by pre-main short pulses were conducted by a series of codes, which had been tested by experiments. Simulation results show that, adopting driven conditions of 2%-3% pre-pulse, 6-8 ns pre-main pulse interval and 40 TW/cm 2 power intensity, a gain area of 19.6 nm laser line beyond 60 μm and gain duration of 90 ps can be obtained. Furthermore, with 16 mm plane target, the gain gets to 11.8/cm, and if 6 mrad/cm curved target is adopted, it reaches to 13.3/cm, and small signal gain-length product of single target is about 21.3, which means that saturated gain can be realized by a single target. With double targets opposite coupling, gain-length product can reach 38.4, deep saturation can be gotten, and XRL source required by demonstration of application is out of question

Ileal transposition surgery produces ileal length-dependent changes in food intake, body weight, gut hormones and glucose metabolism in rats.

Science.gov (United States)

Ramzy, A R; Nausheen, S; Chelikani, P K

2014-03-01

Enhanced stimulation of the lower gut is hypothesized to play a key role in the weight loss and resolution of diabetes following bariatric surgeries. Ileal transposition (IT) permits study of the effects of direct lower gut stimulation on body weight, glucose homeostasis and other metabolic adaptations without the confounds of gastric restriction or foregut exclusion. However, the underlying mechanisms and the length of the ileum sufficient to produce metabolic benefits following IT surgery remain largely unknown. To determine the effects of transposing varying lengths of the ileum to upper jejunum on food intake, body weight, glucose tolerance and lower gut hormones, and the expression of key markers of glucose and lipid metabolism in skeletal muscle and adipose tissue in rats. Adult male Sprague-Dawley rats (n=9/group) were subjected to IT surgery with translocation of 5, 10 or 20 cm of the ileal segment to proximal jejunum or sham manipulations. Daily food intake and body weight were recorded, and an intraperitoneal glucose tolerance test was performed. Blood samples were assayed for hormones and tissue samples for mRNA (RT-qPCR) and/or protein abundance (immunoblotting) of regulatory metabolic markers. We demonstrate that IT surgery exerts ileal length-dependent effects on multiple parameters including: (1) decreased food intake and weight gain, (2) improved glucose tolerance, (3) increased tissue expression and plasma concentrations of glucagon-like peptide-1 (GLP-1) and peptide YY (PYY), and decreased leptin concentrations and (4) upregulation of key markers of glucose metabolism (glucose transporter-4 (GLUT-4), insulin receptor substrate 1 (IRS-1), adenosine monophosphate-activated protein kinase (AMPK), hexokinase (HK) and phosphofructokinase (PFK)) together with a downregulation of lipogenic markers (fatty acid synthase (FAS)) in muscle and adipose tissue. Together, our data demonstrate that the reduction in food intake and weight gain, increase in lower

Influence of pellet diameter and length on the quality of pellets and performance, nutrient utilisation and digestive tract development of broilers fed on wheat-based diets.

Science.gov (United States)

Abdollahi, M R; Ravindran, V; Wester, T J; Ravindran, G; Thomas, D V

2013-06-01

1. The influence of pellet diameter and length on the quality of pellets and performance, nutrient utilisation and digestive tract development of broilers given wheat-based diets was examined from 10 to 42 d of age. The experimental design was a 2 × 2 factorial arrangement of treatments evaluating two pellet diameters (3 and 4.76 mm) and two pellet lengths (3 and 6 mm). From 0 to 9 d of age, all birds were offered a common starter diet pelleted with a 3-mm diameter die and 3-mm length. Broiler grower (d 10 to 21) and finisher (d 22 to 42) diets, based on wheat, were formulated and then subjected to the 4 different treatments. 2. In grower diets, increasing pellet diameter and pellet length reduced the gelatinised starch (GS) content of the diets. In finisher diets, GS content of 3-mm diameter pellets did not change with increasing pellet length but decreased in 4.76-mm diameter pellets. 3. In grower and finisher diets, increments in intact pellet weight, pellet durability index and pellet hardness with increasing pellet length were greater in 3-mm diameter pellets than those with 4.76-mm diameter. 4. Increasing pellet length from 3 to 6 mm increased apparent metabolisable energy values. Neither the interaction nor main effects were significant for the ileal digestibility of nitrogen and starch. 5. During the grower period (d 10 to 21), birds given pellets of 6-mm length had greater body-weight gain than those given 3-mm length pellets. Feeding 6-mm length pellets decreased feed per body-weight gain compared to 3-mm length pellets. During the finisher (d 22 to 42) and whole grow-out (d 10 to 42) periods, while different pellet lengths had no effect on feed per body-weight gain values at 3-mm pellet diameter, increasing the pellet length decreased feed per body-weight gain at 4.76-mm pellet diameter. 6. Increasing pellet diameter and pellet length reduced the relative length of duodenum. Birds given 3-mm diameter pellets had heavier proventriculus compared to

Optimizing Penile Length in Patients Undergoing Partial Penectomy for Penile Cancer: Novel Application of the Ventral Phalloplasty Oncoplastic Technique

Directory of Open Access Journals (Sweden)

Jared J. Wallen

2014-10-01

Full Text Available The ventral phalloplasty (VP has been well described in modern day penile prosthesis surgery. The main objectives of this maneuver are to increase perceived length and patient satisfaction and to counteract the natural 1-2 cm average loss in length when performing implantation of an inflatable penile prosthesis. Similarly, this video represents a new adaptation for partial penectomy patients. One can only hope that the addition of the VP for partial penectomy patients with good erectile function will increase their quality of life. The patient in this video is a 56-year-old male who presented with a 4.0x3.5x1.0 cm, pathologic stage T2 squamous cell carcinoma of the glans penis. After partial penectomy with VP and inguinal lymph node dissection, pathological specimen revealed negative margins, 3/5 right superficial nodes and 1/5 left superficial nodes positive for malignancy. The patient has been recommended post-operative systemic chemotherapy (with external beam radiotherapy based on the multiple node positivity and presence of extranodal extension. The patient’s pre-operative penile length was 9.5 cm, and after partial penectomy with VP, penile length is 7 cm.

Maternal Prepregnancy Body Mass Index and Gestational Weight Gain on Offspring Overweight in Early Infancy

Science.gov (United States)

Li, Nan; Liu, Enqing; Guo, Jia; Pan, Lei; Li, Baojuan; Wang, Ping; Liu, Jin; Wang, Yue; Liu, Gongshu; Hu, Gang

2013-01-01

Objective The aim of the present study was to evaluate the association of maternal prepregnancy body mass index (BMI) and gestational weight gain (GWG) with anthropometry in the offspring from birth to 12 months old in Tianjin, China. Methods Between 2009 and 2011, health care records of 38,539 pregnant women had been collected, and their children had been measured body weight and length at birth, 3, 6, 9 and 12 months of age. The independent and joint associations of pre-pregnancy BMI and GWG based on the Institute of Medicine (IOM) guidelines with anthropometry in the offspring were examined using General Linear Model and Logistic Regression. Results Prepregnancy BMI and maternal GWG were positively associated with Z-scores for birth weight-for-gestational age, birth length-for-gestational age, and birth weight-for-length. Infants born to mothers with excessive GWG had the greatest changes in Z-scores for weight-for-age from birth to Month 3, and from Month 6 to Month 12, and the greatest changes in Z-scores for length-for-age from birth to months 3 and 12 compared with infants born to mothers with adequate GWG. Excessive GWG was associated with an increased risk of offspring overweight or obesity at 12 months old in all BMI categories except underweight. Conclusions Maternal prepregnancy overweight/obesity and excessive GWG were associated with greater weight gain and length gain of offspring in early infancy. Excessive GWG was associated with increased infancy overweight and obesity risk. PMID:24204979

The all-fiber cladding-pumped Yb-doped gain-switched laser.

Science.gov (United States)

Larsen, C; Hansen, K P; Mattsson, K E; Bang, O

2014-01-27

Gain-switching is an alternative pulsing technique of fiber lasers, which is power scalable and has a low complexity. From a linear stability analysis of rate equations the relaxation oscillation period is derived and from it, the pulse duration is defined. Good agreement between the measured pulse duration and the theoretical prediction is found over a wide range of parameters. In particular we investigate the influence of an often present length of passive fiber in the cavity and show that it introduces a finite minimum in the achievable pulse duration. This minimum pulse duration is shown to occur at longer active fibers length with increased passive length of fiber in the cavity. The peak power is observed to depend linearly on the absorbed pump power and be independent of the passive fiber length. Given these conclusions, the pulse energy, duration, and peak power can be estimated with good precision.

DICKE’S SUPERRADIANCE IN ASTROPHYSICS. I. THE 21 cm LINE

Energy Technology Data Exchange (ETDEWEB)

Rajabi, Fereshteh; Houde, Martin [Department of Physics and Astronomy, The University of Western Ontario, London, ON, N6A 3K7 (Canada)

2016-08-01

We have applied the concept of superradiance introduced by Dicke in 1954 to astrophysics by extending the corresponding analysis to the magnetic dipole interaction characterizing the atomic hydrogen 21 cm line. Although it is unlikely that superradiance could take place in thermally relaxed regions and that the lack of observational evidence of masers for this transition reduces the probability of detecting superradiance, in situations where the conditions necessary for superradiance are met (close atomic spacing, high velocity coherence, population inversion, and long dephasing timescales compared to those related to coherent behavior), our results suggest that relatively low levels of population inversion over short astronomical length-scales (e.g., as compared to those required for maser amplification) can lead to the cooperative behavior required for superradiance in the interstellar medium. Given the results of our analysis, we expect the observational properties of 21 cm superradiance to be characterized by the emission of high-intensity, spatially compact, burst-like features potentially taking place over short periods ranging from minutes to days.

Light intensity dependent Debye screening length in undoped photorefractive titanosillenite crystals

OpenAIRE

de Oliveira, I; Frejlich, J

2012-01-01

We report on the experimental evidence of the light intensity dependence of the Debye screening length l(s) in undoped photorefractive titanosillenite crystals (Bi12TiO20) by measuring the holographic gain and diffraction efficiency in a two-wave mixing experiment under 532 nm wavelength laser light. Debye length shows saturation at high values of the light intensity. Results are in agreement with the theoretical development. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/...

Impact of preoperative patient characteristics on posturethroplasty recurrence: The significance of stricture length and prior treatments

Directory of Open Access Journals (Sweden)

Jibril Oyekunle Bello

2016-01-01

Full Text Available Introduction: Urethral strictures are common in urologic practice of Sub-Saharan Africa including Nigeria. We determine the rate of stricture recurrence following urethroplasty for anterior urethral strictures and evaluate preoperative variables that predict of stricture recurrence in our practice. Subjects and Methods: Thirty-six men who had urethroplasty for proven anterior urethral stricture disease between February 2012 and January 2015 were retrospectively analyzed. Preoperative factors including age, socioeconomic factors, comorbidities, etiology of strictures, stricture location, stricture length, periurethral spongiofibrosis, and prior stricture treatments were assessed for independent predictors of stricture recurrence. Results: The median age was 49.5 years (range 21-90, median stricture length was 4 cm (range 1-18 cm and the overall recurrence rate was 27.8%. Postinfectious strictures, pan urethral strictures or multiple strictures involving the penile and bulbar urethra were more common. Most patients had penile circular fasciocutaneous flap urethroplasty. Following univariate analysis of potential preoperative predictors of stricture recurrence, stricture length, and prior treatments with dilations or urethrotomies were found to be significantly associated with stricture recurrence. On multivariate analysis, they both remained statistically significant. Patients who had prior treatments had greater odds of having a recurrent stricture (odds ratio 18, 95% confidence interval [CI] 1.4-224.3. Stricture length was dichotomized based on receiver operating characteristic (ROC analysis, and strictures of length ≥5 cm had significantly greater recurrence (area under ROC curve of 0.825, 95% CI 0.690-0.960, P = 0.032. Conclusion: Patients who had prior dilatations or urethrotomies and those with long strictures particularly strictures ≥5 cm have significantly greater odds of developing a recurrence following urethroplasty in Nigerian

Dual-layer electrode-driven liquid crystal lens with electrically tunable focal length and focal plane

Science.gov (United States)

Zhang, Y. A.; Lin, C. F.; Lin, J. P.; Zeng, X. Y.; Yan, Q.; Zhou, X. T.; Guo, T. L.

2018-04-01

Electric-field-driven liquid crystal (ELC) lens with tunable focal length and their depth of field has been extensively applied in 3D display and imaging systems. In this work, a dual-layer electrode-driven liquid crystal (DELC) lens with electrically tunable focal length and controllable focal plane is demonstrated. ITO-SiO2-AZO electrodes with the dual-layer staggered structure on the top substrate are used as driven electrodes within a LC cell, which permits the establishment of an alternative controllability. The focal length of the DELC lens can be adjusted from 1.41 cm to 0.29 cm when the operating voltage changes from 15 V to 40 V. Furthermore, the focal plane of the DELC lens can selectively move by changing the driving method of the applied voltage to the next driven electrodes. This work demonstrates that the DELC lens has potential applications in imaging systems because of electrically tunable focal length and controllable focal plane.

National proficiency-gain curves for minimally invasive gastrointestinal cancer surgery.

Science.gov (United States)

Mackenzie, H; Markar, S R; Askari, A; Ni, M; Faiz, O; Hanna, G B

2016-01-01

Minimal access surgery for gastrointestinal cancer has short-term benefits but is associated with a proficiency-gain curve. The aim of this study was to define national proficiency-gain curves for minimal access colorectal and oesophagogastric surgery, and to determine the impact on clinical outcomes. All adult patients undergoing minimal access oesophageal, colonic and rectal surgery between 2002 and 2012 were identified from the Hospital Episode Statistics database. Proficiency-gain curves were created using risk-adjusted cumulative sum analysis. Change points were identified, and bootstrapping was performed with 1000 iterations to identify a confidence level. The primary outcome was 30-day mortality; secondary outcomes were 90-day mortality, reintervention, conversion and length of hospital stay. Some 1696, 15 008 and 16 701 minimal access oesophageal, rectal and colonic cancer resections were performed during the study period. The change point in the proficiency-gain curve for 30-day mortality for oesophageal, rectal and colonic surgery was 19 (confidence level 98·4 per cent), 20 (99·2 per cent) and three (99·5 per cent) procedures; the mortality rate fell from 4·0 to 2·0 per cent (relative risk reduction (RRR) 0·50, P = 0·033), from 2·1 to 1·2 per cent (RRR 0·43, P curve for reintervention in oesophageal, rectal and colonic resection was 19 (98·1 per cent), 32 (99·5 per cent) and 26 (99·2 per cent) procedures respectively. There were also significant proficiency-gain curves for 90-day mortality, conversion and length of stay. The introduction of minimal access gastrointestinal cancer surgery has been associated with a proficiency-gain curve for mortality and major morbidity at a national level. Unnecessary patient harm should be avoided by appropriate training and monitoring of new surgical techniques. © 2015 BJS Society Ltd Published by John Wiley & Sons Ltd.

Separation and recovery of Cm from Cm-Pu mixed oxide samples containing Am impurity

International Nuclear Information System (INIS)

Hirokazu Hayashi; Hiromichi Hagiya; Mitsuo Akabori; Yasuji Morita; Kazuo Minato

2013-01-01

Curium was separated and recovered as an oxalate from a Cm-Pu mixed oxide which had been a 244 Cm oxide sample prepared more than 40 years ago and the ratio of 244 Cm to 240 Pu was estimated to 0.2:0.8. Radiochemical analyses of the solution prepared by dissolving the Cm-Pu mixed oxide in nitric acid revealed that the oxide contained about 1 at% of 243 Am impurity. To obtain high purity curium solution, plutonium and americium were removed from the solution by an anion exchange method and by chromatographic separation using tertiary pyridine resin embedded in silica beads with nitric acid/methanol mixed solution, respectively. Curium oxalate, a precursor compound of curium oxide, was prepared from the purified curium solution. 11.9 mg of Cm oxalate having some amounts of impurities, which are 243 Am (5.4 at%) and 240 Pu (0.3 at%) was obtained without Am removal procedure. Meanwhile, 12.0 mg of Cm oxalate (99.8 at% over actinides) was obtained with the procedure including Am removals. Both of the obtained Cm oxalate sample were supplied for the syntheses and measurements of the thermochemical properties of curium compounds. (author)

A sub-cm micromachined electron microscope

Science.gov (United States)

Feinerman, A. D.; Crewe, D. A.; Perng, D. C.; Shoaf, S. E.; Crewe, A. V.

1993-01-01

A new approach for fabricating macroscopic (approximately 10x10x10 mm(exp 3)) structures with micron accuracy has been developed. This approach combines the precision of semiconductor processing and fiber optic technologies. A (100) silicon wafer is anisotropically etched to create four orthogonal v-grooves and an aperture on each 10x12 mm die. Precision 308 micron optical fibers are sandwiched between the die to align the v-grooves. The fiber is then anodically bonded to the die above and below it. This procedure is repeated to create thick structures and a stack of 5 or 6 die will be used to create a miniature scanning electron microscope (MSEM). Two die in the structure will have a segmented electrode to deflect the beam and correct for astigmatism. The entire structure is UHV compatible. The performance of an SEM improves as its length is reduced and a sub-cm 2 keV MSEM with a field emission source should have approximately 1 nm resolution. A low voltage high resolution MSEM would be useful for the examination of biological specimens and semiconductors with a minimum of damage. The first MSEM will be tested with existing 6 micron thermionic sources. In the future a micromachined field emission source will be used. The stacking technology presented in this paper can produce an array of MSEMs 1 to 30 mm in length with a 1 mm or larger period. A key question being addressed by this research is the optimum size for a low voltage MSEM which will be determined by the required spatial resolution, field of view, and working distance.

Mode group specific amplification length in an asymmetric LPG assisted few-mode EDFA

Science.gov (United States)

Rastogi, Vipul; Gaur, Ankita; Aschieri, Pierre; Dussardier, Bernard

2017-01-01

This article presents a scheme for few-mode EDFA, which allows to choose independent amplification lengths for different mode groups. The EDF is a dual concentric core fiber, where the central core is connected to the line FMF and the ring core is doped with erbium to provide amplification. The modes of FMF are launched into the central core of the EDF, are converted into ring modes using LPG for amplification and then converted back into central core modes using another LPG. The distance between the LPGs determines the amplification length. The amplification length, can thus, be chosen for a given mode group. We demonstrate the working of this concept by choosing LP11 and LP21 mode groups of the FMF and show that a suitable choice of amplification lengths for the two mode groups can tailor the differential modal gain (DMG) to any desired value. We demonstrate achieving zero DMG among all the mode of LP11 and LP21 mode groups using this concept while having gain in excess of 20 dB. The study should be useful for optical fiber communication system employing space-division multiplexing (SDM).

344 cm x 86 cm low mass vacuum window

International Nuclear Information System (INIS)

Reimers, R.M.; Porter, J.; Meneghetti, J.; Wilde, S.; Miller, R.

1983-08-01

The LBL Heavy Ion Spectrometer System (HISS) superconducting magnet contains a 1 m x 3.45 m x 2 m vacuum tank in its gap. A full aperture thin window was needed to minimize background as the products of nuclear collisions move from upstream targets to downstream detectors. Six windows were built and tested in the development process. The final window's unsupported area is 3m 2 with a 25 cm inward deflection. The design consists of a .11 mm Nylon/aluminum/polypropylene laminate as a gas seal and .55 mm woven aramid fiber for strength. Total mass is 80 milligrams per cm 2 . Development depended heavily on past experience and testing. Safety considerations are discussed

Quantum-mechanical analysis of low-gain free-electron laser oscillators

Science.gov (United States)

Fares, H.; Yamada, M.; Chiadroni, E.; Ferrario, M.

2018-05-01

In the previous classical theory of the low-gain free-electron laser (FEL) oscillators, the electron is described as a point-like particle, a delta function in the spatial space. On the other hand, in the previous quantum treatments, the electron is described as a plane wave with a single momentum state, a delta function in the momentum space. In reality, an electron must have statistical uncertainties in the position and momentum domains. Then, the electron is neither a point-like charge nor a plane wave of a single momentum. In this paper, we rephrase the theory of the low-gain FEL where the interacting electron is represented quantum mechanically by a plane wave with a finite spreading length (i.e., a wave packet). Using the concepts of the transformation of reference frames and the statistical quantum mechanics, an expression for the single-pass radiation gain is derived. The spectral broadening of the radiation is expressed in terms of the spreading length of an electron, the relaxation time characterizing the energy spread of electrons, and the interaction time. We introduce a comparison between our results and those obtained in the already known classical analyses where a good agreement between both results is shown. While the correspondence between our results and the classical results are shown, novel insights into the electron dynamics and the interaction mechanism are presented.

Receiver gain function: the actual NMR receiver gain

OpenAIRE

Mo, Huaping; Harwood, John S.; Raftery, Daniel

2010-01-01

The observed NMR signal size depends on the receiver gain parameter. We propose a receiver gain function to characterize how much the raw FID is amplified by the receiver as a function of the receiver gain setting. Although the receiver is linear for a fixed gain setting, the actual gain of the receiver may differ from what the gain setting suggests. Nevertheless, for a given receiver, we demonstrate that the receiver gain function can be calibrated. Such a calibration enables accurate compar...

Plasma influence on the dispersion properties of finite-length, corrugated waveguides

Science.gov (United States)

Shkvarunets, A.; Kobayashi, S.; Weaver, J.; Carmel, Y.; Rodgers, J.; Antonsen, T. M., Jr.; Granatstein, V. L.; Destler, W. W.; Ogura, K.; Minami, K.

1996-03-01

We present an experimental study of the electromagnetic properties of transverse magnetic modes in a corrugated-wall cavity filled with a radially inhomogeneous plasma. The shifts of the resonant frequencies of a finite-length, corrugated cavity were measured as a function of the background plasma density and the dispersion diagram was reconstructed up to a peak plasma density of 1012 cm-3. Good agreement with a calculated dispersion diagram is obtained for plasma densities below 5×1011 cm-3.

QTL-mapping in mink (Neovison vison) shows evidence for QTL for guard hair thickness, guard hair length and skin length

DEFF Research Database (Denmark)

Thirstrup, Janne Pia; Labouriau, Rodrigo; Guldbrandtsen, Bernt

2011-01-01

Fur quality in mink (Neovison vison) is a composite trait, consisting of e.g. guard hair length, guard hair thickness and density of wool. A genome wide QTL search was performed to detect QTL for fur quality traits in mink. Here we present the results of QTL analyses for guard hair length, guard...... hair thickness and density of wool. Data from an F2-cross was analysed across fourteen chromosomes using 100 microsatellites as markers with a spacing of approximately 20 cM. The two lines used for the F2-cross were Nordic wild mink and American short nap mink. In total 1,083 animals (21 wild type, 25...... short nap, 103 F1 and 934 F2) were marker typed and recorded for the three presented fur quality traits. For the QTL-analyses a regression analysis implemented in QTL Express software was used. Evidence was found for the existence of QTL for guard hair length, guard hair thickness and density of wool...

Gain measurement in a CW medium-power diode pumped Nd:YAG laser amplifier by ASE analysis

International Nuclear Information System (INIS)

Razzaghi, D; Hajiesmaeilbaigi, F; Ruzbehani, M

2014-01-01

Using the relation between amplified spontaneous emission intensity and gain, a set of formulas is derived for gain evaluation by comparing fluorescence yield in two different lengths of the active medium. Experimental measurements are carried out and gain is calculated by solving the derived formula. For comparison, measurements are also carried out using the probe beam method, which shows good agreement between the two methods in a typical CW medium-power diode pumped Nd:YAG amplifier. (paper)

FISHING GROUND, CACTH COMPOSITION, HOOK RATE AND LENGTH DISTRIBUTION OF BILLFISHES CAUGHT BY TUNA LONG LINE IN INDIAN OCEAN

Directory of Open Access Journals (Sweden)

Fathur Rochman

2013-12-01

Full Text Available Billfishes area by cacth of tuna long line vessels in Indian Ocean. Billfish are consist of swordfish Xiphias gladius, black marlin Makaira indica, indo facific blue marlin Makaira mazara, stripe marlin Tetrapturus audax, indo facific sailfish Istiophorus platypterus and shortbill spearfish Tetrapturus angustirostris. Besides that, billfishes also have important economic value compared with tuna as an exsported species such as swordfish and marlin. To optimize the catch of billfishes in Indian Ocean, data and information of potential fishing ground, size and catch composition of this species are needed. The billfishes cacth composition collected in 2011 were dominated by 45% swordfish, 20% black marlin, 19% blue marlin,9% short bill spearfish, 6% sailfish and 1%stripe marlin. The billfishes size range which were caught between 60 - 280 cm LJFL (Lower Jaw Fork Length. The sword fish average length was 150 cm, blue marlin 197 cm, black Marlin 189 cm, sailfish 150cm ,short bill spearfish 144 cm and stripe marlin159 cm. From this observation, it was found that most of billfishes caught were in mature.

Optical gain in colloidal quantum dots achieved with direct-current electrical pumping

Science.gov (United States)

Lim, Jaehoon; Park, Young-Shin; Klimov, Victor I.

2018-01-01

Chemically synthesized semiconductor quantum dots (QDs) can potentially enable solution-processable laser diodes with a wide range of operational wavelengths, yet demonstrations of lasing from the QDs are still at the laboratory stage. An important challenge--realization of lasing with electrical injection--remains unresolved, largely due to fast nonradiative Auger recombination of multicarrier states that represent gain-active species in the QDs. Here we present population inversion and optical gain in colloidal nanocrystals realized with direct-current electrical pumping. Using continuously graded QDs, we achieve a considerable suppression of Auger decay such that it can be outpaced by electrical injection. Further, we apply a special current-focusing device architecture, which allows us to produce high current densities (j) up to ~18 A cm-2 without damaging either the QDs or the injection layers. The quantitative analysis of electroluminescence and current-modulated transmission spectra indicates that with j = 3-4 A cm-2 we achieve the population inversion of the band-edge states.

Gain optimization and saturation of the Xe III 109 nm auger laser

International Nuclear Information System (INIS)

Macklin, J.J.; Sher, M.H.; Barty, C.P.J.; King, D.A.; Yin, G.Y.; Harris, S.E.; Young, J.F.

1988-01-01

The authors describe the construction and operation of a 109 nm, photoionization-pumped, single-pass laser in Xe III. The laser is pumped by soft x-rays emitted from a laser-produced plasma in a traveling-wave geometry. Using a 3.5 J, 300 psec, 1064 nm laser pump pulse, they measure a small-signal gain coefficient of 4.4 cm -1 and a total small signal gain of exp(40). The laser is fully saturated and produces an output energy of 20 μJ in a beam with 10 mrad divergence

Dye gain gold NW array of surface plasmon polariton waveguide

Directory of Open Access Journals (Sweden)

Jun Zhu

Full Text Available Plasmon lasers can support ultrasmall mode confinement and ultrafast dynamics with device feature sizes below the diffraction limit. At present in the single visible light frequency, the optical gain method of constraint SPP on metal nanowires structure reported less. We design the gold nanowire array structure, consisting of PMMA and R6G dye molecules as gain, by 488 nm pump in the middle of the nanowires position for wide range of light, use symmetry broken overcome that momentum does not match the photonic and SPP energy conversion. Theoretical analysis shows that dyes provide coherent optical feedback, resulting in nanowires face will observe laser properties of surface plasmons. Feature analysis: the incident light and pump joint strength is greater than the sum of strength which is the incident light, pump respectively. Under the effect of dye molecules gain effective, length of SPP transmission can increase 1 µm. The results achieved in a single optical frequency of stimulated radiation, application of dye optical gain can achieve continuous gain effect. This is for the future development of plasma amplifier and the wavelength laser. Keywords: SPP, Stimulated radiation, Gold nanowires array, Dye molecules

A model to obtain an optimum erbium desity for gain increasing in EDFA

Directory of Open Access Journals (Sweden)

E. Arzi

2003-12-01

Full Text Available   In this paper, we suggest a novel model, based on input pump power and wave guidestructure, to calculate the Er-density profile in Erbium doped fiber amplifiers. This optimization is carried out for both SMF and DSF fibers. These optimized profiles have a Gaussian-like shape. Using the SMF optimized Er-density profile, high gain enhancement is obtained in a relatively short length of fibers. On the other hand, the DSF optimized profile shows small changes in the gain, which agrees with the previously report on other method of gain enhancement. This model is applicable to all active waveguides and any other dopant as well .

Optical gain and absorption of 420 nm InGaN-based laser diodes grown on m-plane GaN substrate

KAUST Repository

Shen, Chao

2014-01-01

Segmented contact method was utilized to measure the gain and absorption spectra at below and above threshold for 420nm m-plane InGaN/GaN laser diode with a comparatively higher peak modal gain of 29.2 cm-1.

Plantar fascia coronal length: a new parameter for plantar fascia assessment.

Science.gov (United States)

Sari, Ahmet Sinan; Demircay, Emre; Cakmak, Gokhan; Sahin, M Sukru; Tuncay, I Cengiz; Altun, Suleyman

2015-01-01

The effects of gender and various anthropometric variables were previously reported as significant predictors of plantar fascia thickness. Although a strong correlation between either the body weight or body mass index (BMI) and plantar fascia thickness were not demonstrated, a moderate relation was stated. We retrospectively investigated the role of gender, height, weight, and body mass index on plantar fascia thickness at the calcaneal origin (PFCO) and 1 cm distal from the calcaneal origin (PF1cm) and the coronal length of the plantar fascia at the calcaneal origin (CLPF) in healthy subjects. The PFCO, PF1cm, and CLPF were retrospectively measured from magnetic resonance images of 100 healthy subjects. The gender, height, weight, and body mass index of the participants were also noted. Gender was a predictive factor for the length of the CLPF. The subjects with a BMI >25 kg/m(2) had a significantly greater PFCO, PF1cm, and CLPF. Height was mildly and BMI and weight were moderately related to the PFCO. However the CLPF showed a better correlation with height, BMI, and weight than that of plantar fascia thickness. CLPF better reflected the role of weight, BMI, and height than its thickness. It is a new parameter that could be valuable in the evaluation of plantar fascia disorders. Copyright © 2015 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Numerical scalings of the decay lengths in the scrape-off layer

DEFF Research Database (Denmark)

Militello, F.; Naulin, V; Nielsen, Anders Henry

2013-01-01

Numerical simulations of L-mode turbulence in the scrape-off layer (SOL) are used to construct power scaling laws for the characteristic decay lengths of the temperature, density and heat flux at the outer mid-plane. Most of the results obtained are in qualitative agreement with the experimental...... observations despite the known limitation of the model. Quantitative agreement is also obtained for some exponents. In particular, an almost linear inverse dependence of the heat flux decay length with the plasma current is recovered. The relative simplicity of the theoretical model used allows one to gain...

Preoperative weight gain might increase risk of gastric bypass surgery.

Science.gov (United States)

Istfan, Nawfal W; Anderson, Wendy A; Apovian, Caroline M; Hess, Donald T; Forse, R Armour

2011-01-01

Weight loss improves the cardiovascular and metabolic risk associated with obesity. However, insufficient data are available about the health effects of weight gain, separate from the obesity itself. We sought to determine whether the changes in body weight before open gastric bypass surgery (OGB) would have a significant effect on the immediate perioperative hospital course. A retrospective chart review of 100 consecutive patients was performed to examine the effects of co-morbidities and body weight changes in the immediate preoperative period on the hospital length of stay and the rate of admission to the surgical intensive care unit (SICU). Of our class III obese patients undergoing OGB, 95% had ≥1 co-morbid condition and an overall SICU admission rate of 18%. Compared with the patients with no perioperative SICU admission, the patients admitted to the SICU had a greater degree of insulin resistance (homeostatic model analysis-insulin resistance 10.8 ± 1.3 versus 5.9 ± 0.5, P = .001), greater serum triglyceride levels (225 ± 47 versus 143 ± 8 mg/dL, P = .003), and had gained more weight preoperatively (.52 ± .13 versus .06 ± .06 lb/wk, P = .003). The multivariate analyses showed that preoperative weight gain was a risk factor for a longer length of stay and more SICU admissions lasting ≥3 days, as were a diagnosis of sleep apnea and an elevated serum triglyceride concentration. The results of the present retrospective study suggest that weight gain increases the risk of perioperative SICU admission associated with OGB, independent of the body mass index. Sleep apnea and elevated serum triglyceride levels were also important determinants of perioperative morbidity. In view of the increasing epidemic of obesity and the popularity of bariatric surgical procedures, we propose that additional clinical and metabolic research focusing on the understanding of the complex relationship among obesity, positive energy balance, weight gain, and perioperative

COMPRIMENTO DA ESTACA DE RAMO NO ENRAIZAMENTO DE GINSENG BRASILEIRO (Pfaffia glomerata SHOOT CUTTING LENGTH ON ROOTING OF BRAZILIAN GINSENG (Pfaffia glomerata

Directory of Open Access Journals (Sweden)

Fernando Teixeira Nicoloso

2001-02-01

Full Text Available A Pfaffia glomerata (Spreng. Pedersen é uma dentre várias espécies conhecidas como ginseng brasileiro e é usada como planta medicinal. O objetivo desse trabalho foi determinar se o comprimento da estaca de ramo influencia o enraizamento da P. glomerata. Os tratamentos usados consistiram de três comprimentos de estacas (10, 15 e 20cm; ± 1cm de variação. As estacas foram obtidas dos 70cm basais de ramos, com 80 a 140cm de comprimento, de plantas possuindo dois anos de idade, cultivadas no Jardim Botânico da UFSM. Utilizou-se o delineamento experimental de blocos ao acaso com três repetições e 30 estacas por unidade experimental. O bloco experimental consistiu de uma bandeja plástica com capacidade para 36 litros de solução nutritiva. O experimento foi instalado no dia 15 de julho de 1998 e conduzido por 44 dias sob condições controladas de temperatura, luminosidade e umidade do ar. Os resultados indicaram que (i o tamanho da estaca não afeta a percentagem de enraizamento, a produção de massa seca de folhas e raízes. Por outro lado, as mudas obtidas de estacas de 10cm apresentam maior número de brotações, comprimento das brotações, massa seca de talos e massa seca total produzida por estaca que as de 20cm; e (ii o uso de estacas com 10cm de comprimento é viável e, conseqüentemente, possibilita a obtenção de um maior número de estacas por ramo.Pfaffia glomerata (Spreng. Pedersen is among several species known as Brazilian ginsengs and it is used as medicinal plant. The aim of this work was to evaluate the length of the shoot cuttings on rooting of P. glomerata. Treatments consisted of three length of cuttings (10, 15, and 20cm; ± 1cm of variation. Cuttings were obtained from the 70cm of the basal portion from shoots of 80 to 140cm of length, from two-year-old plants grown in the Botanical Garden at State University of Santa Maria, RS, Brazil. Treatments were distributed in a completely randomized block design with

The influence of determining the working length with an apex locator on the amount of apically extruded debris following instrumentation with ProTaper Next and HyFlex CM

Directory of Open Access Journals (Sweden)

Ersan Çiçek

2016-01-01

Full Text Available Aim: The amount of apically extruded debris caused by new nickel-titanium rotary systems after determination of the working length (WL with an apex locator has not been investigated. To compare the amount of apically extruded debris with ProTaper Next (PTN and HyFlex CM systems after determination of WL with/without an apex locator. Materials and Methods: Forty-eight extracted mandibular incisor teeth divided into four groups were used in this study. In Groups 1 and 2, a 10 K-file was progressed until it was just visible at the major apical foramen and WL was recorded as 1 mm short. In Groups 3 and 4, the WL was determined with the Root ZX (sensitivity of 0.1 using a 10 K-file. During the instrumentation, the PTN was used to X2 in groups 1 and 3, and the HyFlex CM was used to 25/.06 in groups 2 and 4. Distilled water was used as an irrigant. Debris was collected in tubes then stored in an incubator at 68°C for 5 days to evaporate the distilled water. The Eppendorf tubes, including the extruded debris, were weighed to obtain final weights. The amount of extruded debris was calculated by subtracting the weight of the empty tube from the weight of the dry tube. Data were analyzed by Kruskal–Wallis and Mann–Whitney U-test. Results: Less apically extruded debris was obtained in Group 3, with a significant difference compared to Group 1 and Group 2 (P < 0.05. Conclusions: The usage of apex locator to determine the WL decreased the amount of apically extruded debris. In addition, PTN caused less apical debris extrusion after determination WL with/without apex locator.

Effects of electron irradiation and temperature on 1 ohm-cm and 10 ohm-cm silicon solar cells

Science.gov (United States)

Nicoletta, C. A.

1973-01-01

One OHM-cm and 10 OHM-cm silicon solar cells were exposed to 1.0 MeV electrons at a fixed flux of 10 to the 11th power e/sq cm/sec and fluences of 10 to the 13th power, 10 to the 14th power and 10 to the 15th power e/sq.cm. 1-V curves of the cells were made at room temperature, - 63 C and + or - 143 C after each irradiation. A value of 139.5 mw/sq cm was used as AMO incident energy rate per unit area. The 10 OHM-cm cells appear more efficient than 1 OHM-cm cells after exposure to a fluence greater than 10 to the 14th power e/sq cm. The 1.0 MeV electron damage coefficients for both 1 OHM-cm and 10 OHM-cm cells are somewhat less than those for previously irradiated cells at room temperature. The values of the damage coefficients increase as the cell temperatures decrease. Efficiencies pertaining to maximum power output are about the same as those of n on p silicon cells evaluated previously.

Effect of multipulse waveform on gains of soft X-ray lines of lithium-like aluminum ions in recombining plasmas

International Nuclear Information System (INIS)

Okasaka, Kazunobu; Hara, Tamio; Yamaguchi, Naohiro; Ando, Kozo; Kawachi, Tetsuya; Oyama, Hitoshi

2000-01-01

Using the recombination plasma scheme, we investigated the amplified spontaneous emissions (ASE) from lithium-like aluminum plasmas produced by multipulse laser irradiation. Three types of multipulse waveforms of Nd-glass laser beam were treated. We measured the time-integrated intensities of the 3d-4f (15.5 nm) and the 3d-5f (10.6 nm) lines of lithium-like aluminum ions for 2.5-cm-long and 1.25-cm-long plasmas. The effective time-averaged gains estimated from these time-integrated intensities varied with the multipulse waveforms. using a hydrodynamic simulation, we discussed the time history of plasma parameters in the recombining plasma. We concluded that the modifying multipulse waveform contributed to the effective time-averaged gain by maintaining the helium-like ion density until the gain was generated. (author)

Effects of proton irradiation and temperature on 1 ohm-cm and 10 ohm-cm silicon solar cells

Science.gov (United States)

Nicoletta, C. A.

1973-01-01

The 1 ohm-cm and 10 ohm-cm silicon solar cells were exposed to 1.0 MeV protons at a fixed flux of 10 to the 9th power P/sq cm-sec and fluences of 10 to the 10th power, 10 to the 11th power, 10 to the 12th power and 3 X 10 to the 12th power P/sq cm. I-V curves of the cells were made at room temperature, 65 C and 165 C after each irradiation. A value of 139.5 mw/sq cm was taken as AMO incident energy rate per unit area. Degradation occurred for both uncovered 1 ohm-cm and 10 ohm-cm cells. Efficiencies are generally higher than those of comparable U.S. cells tested earlier. Damage (loss in maximum power efficiency) with proton fluence is somewhat higher for 10 ohm-cm cells, measured at the three temperatures, for fluences above 2 X 10 to the 11th power P/sq cm. Cell efficiency, as expected, changes drastically with temperature.

Low Gain Avalanche Detectors (LGAD) for particle physics and synchrotron applications

Science.gov (United States)

Moffat, N.; Bates, R.; Bullough, M.; Flores, L.; Maneuski, D.; Simon, L.; Tartoni, N.; Doherty, F.; Ashby, J.

2018-03-01

A new avalanche silicon detector concept is introduced with a low gain in the region of ten, known as a Low Gain Avalanche Detector, LGAD. The detector's characteristics are simulated via a full process simulation to obtain the required doping profiles which demonstrate the desired operational characteristics of high breakdown voltage (500 V) and a gain of 10 at 200 V reverse bias for X-ray detection. The first low gain avalanche detectors fabricated by Micron Semiconductor Ltd are presented. The doping profiles of the multiplication junctions were measured with SIMS and reproduced by simulating the full fabrication process which enabled further development of the manufacturing process. The detectors are 300 μm thick p-type silicon with a resistivity of 8.5 kΩcm, which fully depletes at 116 V. The current characteristics are presented and demonstrate breakdown voltages in excess of 500 V and a current density of 40 to 100 nAcm‑2 before breakdown measured at 20oC. The gain of the LGAD has been measured with a red laser (660 nm) and shown to be between 9 and 12 for an external bias voltage range from 150 V to 300 V.

A model to obtain an optimum erbium desity for gain increasing in EDFA

OpenAIRE

E. Arzi; A. Hassani; F. E. Seraji

2003-01-01

  In this paper, we suggest a novel model, based on input pump power and wave guidestructure, to calculate the Er-density profile in Erbium doped fiber amplifiers. This optimization is carried out for both SMF and DSF fibers. These optimized profiles have a Gaussian-like shape. Using the SMF optimized Er-density profile, high gain enhancement is obtained in a relatively short length of fibers. On the other hand, the DSF optimized profile shows small changes in the gain, which agrees with the ...

Gain-enhanced LTCC system-on-package for automotive UMRR applications

KAUST Repository

Ghaffar, Farhan A.

2012-07-28

A novel Low Temperature Co-fired Ceramic (LTCC) based SoP for automotive radar applications is presented. For the first time a combination of a relatively low dielectric constant LTCC substrate and a high dielectric constant LTCC superstrate has been incorporated to enhance the overall gain of the module. The superstrate can provide additional protection to the integrated circuits (IC) in the harsh automotive environment. A custom cavity in the LTCC substrate can accommodate the IC, which feeds an aperture coupled patch antenna array. The cavity is embedded below the ground plane that acts as a shield for the IC from antenna radiation. It is estimated that with mere 10 dBm of transmitted RF power the miniature SoP module (sized 2.0 cm × 2.0 cm × 0.22 cm) can communicate up to 67 m. The design\\'s compactness, robustness, transmission power and resultant communication range are highly suitable for Universal Medium Range Radar (UMRR) applications. © 2010 IEEE.

FTO associations with obesity and telomere length.

Science.gov (United States)

Zhou, Yuling; Hambly, Brett D; McLachlan, Craig S

2017-09-01

This review examines the biology of the Fat mass- and obesity-associated gene (FTO), and the implications of genetic association of FTO SNPs with obesity and genetic aging. Notably, we focus on the role of FTO in the regulation of methylation status as possible regulators of weight gain and genetic aging. We present a theoretical review of the FTO gene with a particular emphasis on associations with UCP2, AMPK, RBL2, IRX3, CUX1, mTORC1 and hormones involved in hunger regulation. These associations are important for dietary behavior regulation and cellular nutrient sensing via amino acids. We suggest that these pathways may also influence telomere regulation. Telomere length (TL) attrition may be influenced by obesity-related inflammation and oxidative stress, and FTO gene-involved pathways. There is additional emerging evidence to suggest that telomere length and obesity are bi-directionally associated. However, the role of obesity risk-related genotypes and associations with TL are not well understood. The FTO gene may influence pathways implicated in regulation of TL, which could help to explain some of the non-consistent relationship between weight phenotype and telomere length that is observed in population studies investigating obesity.

Visual target distance, but not visual cursor path length produces shifts in motor behavior

Directory of Open Access Journals (Sweden)

Nike eWendker

2014-03-01

Full Text Available When using tools effects in body space and distant space often do not correspond. Findings so far demonstrated that in this case visual feedback has more impact on action control than proprioceptive feedback. The present study varies the dimensional overlap between visual and proprioceptive action effects and investigates its impact on aftereffects in motor responses. In two experiments participants perform linear hand movements on a covered digitizer tablet to produce ∩-shaped cursor trajectories on the display. The shape of hand motion and cursor motion (linear vs. curved is dissimilar and therefore does not overlap. In one condition the length of hand amplitude and visual target distance is similar and constant while the length of the cursor path is dissimilar and varies. In another condition the length of the hand amplitude varies while the lengths of visual target distance (similar or dissimilar and cursor path (dissimilar are constant. First, we found that aftereffects depended on the relation between hand path length and visual target distance, and not on the relation between hand and cursor path length. Second, increasing contextual interference did not reveal larger aftereffects. Finally, data exploration demonstrated a considerable benefit from gain repetitions across trials when compared to gain switches. In conclusion, dimensional overlap between visual and proprioceptive action effects modulates human information processing in visually controlled actions. However, adjustment of the internal model seems to occur very fast for this kind of simple linear transformation, so that the impact of prior visual feedback is fleeting.

Calculation of 3-D free electron laser gain: Comparison with simulation and generalization to elliptical cross section

International Nuclear Information System (INIS)

Chin, Yong Ho; Kim, Kwang-Je; Xie, Ming.

1992-08-01

In the previous paper, we have derived a dispersion relation for the free electron laser (FEL) gain in the exponential regime taking account the diffraction and electron's betatron oscillation. Here, we compare the growth rates obtained by solving the dispersion relation with those obtained by simulation calculation for the waterbag and the Gaussian models for the electron's transverse phase space distribution. The agreement is found to be good except for the limiting case where the Rayleigh length is much longer than the gain length (1-D limit). We also generalize the analysis to the case where the electron beam cross section is elliptical as is usually the case in storage rings, and derive the first-order dispersion relation

Children with lower limb length inequality: The measurement of inequality, the timing of physiodesis and gait analysis

NARCIS (Netherlands)

H.I.H. Lampe

1997-01-01

textabstractThe symmetry of the human locomotion apparatus makes inequality of the limbs an aberrant finding for both patient and doctor. 4-15% of the healthy, adult population, has a limb length inequality (LLI) of one cm or more. A minor discrepancy of less than one cm is therefore common and many

Tuning gain and bandwidth of traveling wave tubes using metamaterial beam-wave interaction structures

International Nuclear Information System (INIS)

Lipton, Robert; Polizzi, Anthony

2014-01-01

We employ metamaterial beam-wave interaction structures for tuning the gain and bandwidth of short traveling wave tubes. The interaction structures are made from metal rings of uniform cross section, which are periodically deployed along the length of the traveling wave tube. The aspect ratio of the ring cross sections is adjusted to control both gain and bandwidth. The frequency of operation is controlled by the filling fraction of the ring cross section with respect to the size of the period cell.

Effects of dietary protein levels on length-weight relationships and ...

African Journals Online (AJOL)

Feeding trial involving different protein levels on length–weight relationships and condition factor of Clarias gariepinus was conducted in floating hapa system. Fingerlings (average weight, 4.50± 0.01g and average length, 8.0±0.2 cm) were randomly stocked at 20 fish/1m3. Five diets with crude protein: 40.0, 42.5, 45.0, 47.5 ...

Weight-for-length/height growth curves for children and adolescents in China in comparison with body mass index in prevalence estimates of malnutrition.

Science.gov (United States)

Zong, Xinnan; Li, Hui; Zhang, Yaqin; Wu, Huahong

2017-05-01

It is important to update weight-for-length/height growth curves in China and re-examine their performance in screening malnutrition. To develop weight-for-length/height growth curves for Chinese children and adolescents. A total of 94 302 children aged 0-19 years with complete sex, age, weight and length/height data were obtained from two cross-sectional large-scaled national surveys in China. Weight-for-length/height growth curves were constructed using the LMS method before and after average spermarcheal/menarcheal ages, respectively. Screening performance in prevalence estimates of wasting, overweight and obesity was compared between weight-for-height and body mass index (BMI) criteria based on a test population of 21 416 children aged 3-18. The smoothed weight-for-length percentiles and Z-scores growth curves with length 46-110 cm for both sexes and weight-for-height with height 70-180 cm for boys and 70-170 cm for girls were established. The weight-for-height and BMI-for-age had strong correlation in screening wasting, overweight and obesity in each age-sex group. There was no striking difference in prevalence estimates of wasting, overweight and obesity between two indicators except for obesity prevalence at ages 6-11. This set of smoothed weight-for-length/height growth curves may be useful in assessing nutritional status from infants to post-pubertal adolescents.

Experimental determination of kQ factors for cylindrical ionization chambers in 10 cm × 10 cm and 3 cm × 3 cm photon beams from 4 MV to 25 MV.

Science.gov (United States)

Krauss, A; Kapsch, R P

2014-08-07

For the ionometric determination of absorbed dose to water, Dw, in megavoltage photon beams from a linear accelerator, beam-quality-dependent correction factors, kQ, are used for the ionization chambers. By using a water calorimeter, these factors can be determined experimentally and with substantially lower standard uncertainties compared to calculated values of the kQ, which are published in various dosimetry protocols. In this investigation, kQ for different types of cylindrical ionization chambers (NE 2561, NE 2571, FC 65 G) were determined experimentally in 10 cm × 10 cm photon beams from 4 MV to 25 MV (corresponding beam quality index TPR20,10 from 0.64 to 0.80). The measurements were carried out at the linear accelerator facility of the Physikalisch-Technische Bundesanstalt. It is shown that the kQ factors for a single ionization chamber in 10 cm × 10 cm photon beams can be measured with a relative standard uncertainty of 0.31%. In addition to these measurements in 10 cm × 10 cm fields, kQ factors for the NE 2561 chamber were also determined in smaller 3 cm × 3 cm photon beams between 6 MV and 25 MV. In this case, relative standard uncertainties between 0.35 % and 0.38 % are achieved for the kQ factors. It is found for this ionization chamber, that the ratio of the kQ factors in 3 cm × 3 cm and in 10 cm × 10 cm beams increases with increasing TPR20,10 to reach a value of 1.0095 at TPR20,10 = 0.8 with a relative standard uncertainty of 0.4 %.

Determination of Am-241, Cm-242 and Cm-244 in environmental samples

International Nuclear Information System (INIS)

Afsar, M.; Schuettelkopf, H.

1988-01-01

An analytical procedure for the determination of Am and Cm in environmental, liquid and gaseous effluent samples was developed. It is based on extraction chromatography with subsequent anion and cation exchange to remove matrix elements and to purify Am and Cm, which are then electrode posited from an oxalate/HCl medium. The mean value of the chemical yield is about 90%. A detection limit of 7 μBq/g is achieved. The decontamination factors for important α emitters are > 10 4 . Four analyses/week can be performed by one technician. (orig./RB) [de

Broadband tunability of gain-flattened quantum-well semiconductor lasers with an external grating

International Nuclear Information System (INIS)

Mittelstein, M.; Mehuys, D.; Yariv, A.; Sarfaty, R.; Ungar, J.E.

1989-01-01

Semiconductor injection lasers are known to be tunable over a range of order kΒ · T. Quantum-well lasers, in particular, are shown to exhibit flattened, broadband gain spectra at a particular pumping condition. The gain requirement for a grating-tuned external cavity configuration is examined and is applied to a semiconductor quantum-well laser with an optimized length of gain region. The coupled-cavity formalism is employed to examine the conditions for continuous tuning. The possible tuning range of double-heterostructure lasers is compared to that of quantum-well lasers. The predicted broadband tunability of quantum-well lasers is confirmed experimentally by grating-tuning of uncoated lasers exceeding 120 nm, with single, longitudinal mode output power exceeding 300 mW

The effect of the Thanksgiving Holiday on weight gain

Directory of Open Access Journals (Sweden)

Dinger Mary K

2006-11-01

Full Text Available Abstract Background More people than ever are considered obese and the resulting health problems are evident. These facts highlight the need for identification of critical time periods for weight gain. Therefore the purpose was to assess potential changes that occur in body weight during the Thanksgiving holiday break in college students. Methods 94 college students (23.0 ± 4.6 yrs, 72.1 ± 14.0 kg, 172.6 ± 9.3 cm, 24.0 ± 3.9 kg/m2 reported to the human body composition laboratory at the University of Oklahoma following a 6-hour fast with testing occurring prior to, and immediately following the Thanksgiving holiday break (13 ± 3 days. Body weight (BW was assessed using a balance beam scale while participants were dressed in minimal clothing. Paired t-tests were used to assess changes in BW pre and post Thanksgiving holiday with additional analysis by gender, body mass index (BMI, and class standing (i.e. undergraduate vs. graduate. Results Overall, a significant (P P P 2 group compared to a non significant 0.2 kg gain in the normal group (2. Conclusion These data indicate that participants in our study gained a significant amount of BW (0.5 kg during the Thanksgiving holiday. While an increase in BW of half a kilogram may not be cause for alarm, the increase could have potential long-term health consequences if participants retained this weight gain throughout the college year. Additionally, because the overweight/obese participants gained the greatest amount of BW, this group may be at increased risk for weight gain and further obesity development during the holiday season.

Am I normal? A systematic review and construction of nomograms for flaccid and erect penis length and circumference in up to 15,521 men.

Science.gov (United States)

Veale, David; Miles, Sarah; Bramley, Sally; Muir, Gordon; Hodsoll, John

2015-06-01

To systematically review and create nomograms of flaccid and erect penile size measurements. Study key eligibility criteria: measurement of penis size by a health professional using a standard procedure; a minimum of 50 participants per sample. samples with a congenital or acquired penile abnormality, previous surgery, complaint of small penis size or erectile dysfunction. Synthesis methods: calculation of a weighted mean and pooled standard deviation (SD) and simulation of 20,000 observations from the normal distribution to generate nomograms of penis size. Nomograms for flaccid pendulous [n = 10,704, mean (SD) 9.16 (1.57) cm] and stretched length [n = 14,160, mean (SD) 13.24 (1.89) cm], erect length [n = 692, mean (SD) 13.12 (1.66) cm], flaccid circumference [n = 9407, mean (SD) 9.31 (0.90) cm], and erect circumference [n = 381, mean (SD) 11.66 (1.10) cm] were constructed. Consistent and strongest significant correlation was between flaccid stretched or erect length and height, which ranged from r = 0.2 to 0.6. relatively few erect measurements were conducted in a clinical setting and the greatest variability between studies was seen with flaccid stretched length. Penis size nomograms may be useful in clinical and therapeutic settings to counsel men and for academic research. © 2014 The Authors. BJU International © 2014 BJU International.

Estimation of Length-Weight Relationship and Proximate Composition of Catfish (Clarias gariepinus Burchell, 1822 from Two Different Culture Facilities

Directory of Open Access Journals (Sweden)

Olaniyi Alaba Olopade

2015-06-01

Full Text Available This study was carried out to determine and compare the proximate composition and length weight relationship of C. gariepinus from two culture systems (earthen and concrete ponds. The fish samples were collected from three fish farms with same cultural condition in different areas of Obio-akpor Local Government Area of Rivers State, Nigeria. Result on the length- weight relationship revealed that C.gariepinus reared in concrete tank had a total length of 15.50- 49.00cm with a mean of 32.71cm and weight of 150-625g, while total length of C. gariepinus reared in the earthen pond ranged from 19.90-58.0cm with a mean of 39.8cm and weight of 195-825g. The T- test shows that the total length of earthen pond were significantly higher than the concrete tank and the weight in the earthen pond was significantly higher than the concrete tank. Parameters of proximate composition analysed were moisture, protein, lipid, carbohydrate, ash and fiber from the fish flesh. Protein content showed a significantly higher in the earthen ponds than the concrete tanks. Ash contents varied from 1.5±1.66-7.4±0.67% in the concrete tanks and were significantly higher than the earthen ponds which ranged from 3.1±0.94-4.5±2.11%. Lipid was significantly higher in earthen ponds than concrete tanks. Generally, the two culture systems have a significant influence on length–weight relationship and nutritional value of C. gariepinus. However, C. gariepinus reared in concrete tank had a heavier body weight than earthen pond and also C. gariepinus reared in earthen pond had highest nutritive values than the concrete tank.

Growth of the silverside Atherinella brasiliensis in a subtropical estuary with some insights concerning the weight-length relationship

Directory of Open Access Journals (Sweden)

BARBARA M. DE CARVALHO

Full Text Available ABSTRACT Specimens of Brazilian silverside (Atherinella brasiliensis, n=9672 with a length range of 1.5 to 14.2 cm were captured in the intertidal areas of the Estuarine Complex of Paranaguá, Brazil, between August 2010 and July 2011. The species’ weight-length relationship was represented by the equation W=0.00533 L3.136 with a slightly positive allometry (b>3 and could be divided into two growth stanzas: W = W1 + W2; Stanza 1: W1= SW. (0.005239 L3.152; Stanza 2: W2= (1 - SW. (0.000699 L3.913; Switch-Function: SW = [1 + e1.204 (L - 11.66]-1. The breakpoint between the first and second stanza (11.66 cm matches published values for the estimated size at first maturity of adult females. Frequency distributions indicate that the species is present in the shallow areas of the Estuarine Complex of Paranaguá during all phases of its ontogenetic development, with the recruitment of juveniles taking place between October and November. Modal displacement was monitored throughout 12 months. The von Bertalanffy growth model and longevity was estimated as follow: asymptotic length (L∞ of 17.5 cm, growth coefficient (K of 0.89 (year-1 and longevity (A95 of 3.33 years. We present some considerations with regard to the general methodology for adjusting weight-length relationships.

High-frequency binge eating predicts weight gain among veterans receiving behavioral weight loss treatments.

Science.gov (United States)

Masheb, Robin M; Lutes, Lesley D; Kim, Hyungjin Myra; Holleman, Robert G; Goodrich, David E; Janney, Carol A; Kirsh, Susan; Richardson, Caroline R; Damschroder, Laura J

2015-01-01

To assess for the frequency of binge eating behavior and its association with weight loss in an overweight/obese sample of veterans. This study is a secondary analysis of data from the ASPIRE study, a randomized effectiveness trial of weight loss among veterans. Of the 481 enrolled veterans with overweight/obesity, binge eating frequency was obtained by survey for 392 (82%). The majority (77.6%) reported binge eating, and 6.1% reported high-frequency binge eating. Those reporting any binge eating lost 1.4% of body weight, decreased waist circumference by 2.0 cm, and had significantly worse outcomes than those reporting never binge eating who lost about double the weight (2.7%) and reduced waist circumference by twice as much (4.2 cm). The high-frequency binge group gained 1.4% of body weight and increased waist circumference by 0.3 cm. High rates of binge eating were observed in an overweight/obese sample of veterans enrolled in weight loss treatment. The presence of binge eating predicted poorer weight loss outcomes. Furthermore, high-frequency binge eating was associated with weight gain. These findings have operational and policy implications for developing effective strategies to address binge eating in the context of behavioral weight loss programs for veterans. © 2014 The Obesity Society.

Feasibility of achieving gain in transition to the ground state of C VI at 3.4 nm

International Nuclear Information System (INIS)

Avitzour, Yoav; Suckewer, Szymon

2007-01-01

We present numerical studies of recombination gain in the transition to the ground state of H-like C (2→1 transition at λ=3.4 nm). It is shown that high gain (up to about 180 cm -1 ) can be achieved using currently available, relatively compact, laser technology. The model includes the ionization of the plasma by an ultraintense, ultrashort laser pulse, followed by plasma expansion, cooling, and recombination. Transient population inversion is generated during the recombination process. We investigate the behavior of the gain with respect to different plasma parameters and pump pulse parameters and explain how the different properties of the plasma and the pump pulse affect the gain

Can hip arthroscopy be performed with conventional knee-length instrumentation?

Science.gov (United States)

Pascual-Garrido, Cecilia; McConkey, Mark O; Young, David A; Bravman, Jonathan T; Mei-Dan, Omer

2014-12-01

The purpose of this study was to determine whether hip arthroscopy can be performed using conventional knee-length arthroscopy instrumentation. We included 116 consecutive hip arthroscopies (104 patients) in this study. Age, side of surgery, height (in inches), weight (in pounds), body mass index (BMI), and a subjective assessment of body type (1, muscular; 2, somewhat overweight; 3, overweight; 4, thin; and 5, normal weight) were recorded. The depth from the skin at 2 portal sites to 3 commonly accessed positions (12 o'clock, 3 o'clock, and acetabular fossa) was assessed using a guide with marked notches (in millimeters). Subgroup analysis was performed according to BMI and subjective biotype for each patient. We included 104 patients with a mean age of 35 years (range, 14 to 55 years). As categorized by BMI, 60% of patients were normal weight, 22% were overweight, 16% were obese, and 2% were underweight. All but 8 procedures were performed with conventional knee-length arthroscopic shavers and burrs. The 8 procedures that needed additional hip instrumentation were performed in patients who required ligamentum teres debridement or those with iliopsoas tenotomy. Overall, the distance from skin to socket was less than 11 cm at the 12-o'clock and 3-o'clock positions from both the anterolateral and anterior portals. Obese and overweight patients had statistically longer distances from skin to socket at all 3 measurement points compared with underweight and normal-weight patients. Considering biotype, the distances from skin to socket in underweight, normal-weight, and muscular patients were all equal to or less than 10 cm. The distance from skin to socket at the 12- and 3-o'clock positions is less than 11 cm, suggesting that hip arthroscopy can be performed with conventional knee-length instrumentation devices. In obese and overweight patients and patients requiring ligamentum teres debridement or iliopsoas tendon release, specific hip arthroscopic tools should

Effects of hole tapering on cone-beam collimation for brain SPECT imaging

International Nuclear Information System (INIS)

Park, Mi-Ae; Kijewski, Marie Foley; Moore, Stephen C.

2006-01-01

New collimator manufacturing technologies, such as photoetching, electrical discharge machining, and stereolithography, expand the range of possible cone-beam collimator configurations. For example, it might now be possible for brain SPECT to make a short-focusing cone-beam collimator with tapered holes that increase in size with distance from the collimator surface; conventional lead-casting techniques produce holes of constant size and, consequently, varying septal thicknesses. Moreover, the changes in hole shape and loss of close packing due to focusing leads to thicker septa in the collimator periphery, especially for shorter focal lengths. We investigated the potential advantages of new cone-beam collimator manufacturing processes, and proposed a new design for very short focal-length collimators for brain SPECT imaging. We compared three cone-beam collimators, a conventional collimator manufactured using casting techniques (CC), a novel collimator with uniform hole sizes on the collimator surface and constant hole size through the collimator thickness (FC), and a novel collimator with uniform hole sizes and tapered holes (TC). We determined the resolution of each collimator analytically for focal lengths ranging from 20-50 cm, and adjusted the entrance hole sizes of FC and TC to equalize resolution of all collimators. Sensitivity was calculated at several locations by Monte Carlo simulation. Sensitivity was higher at all points for TC and FC than for CC, and higher for TC than for FC. The differences in sensitivity were larger for shorter focal lengths. For a point on the focal line at 10 cm in front of the collimator entrance surface, the sensitivity gain for TC compared to CC was 7% and 45% for focal lengths of 50 and 20 cm, respectively. The sensitivity gain for a 20-cm focal length, compared to CC, averaged over all locations, was 44% for TC and 23% for FC. We have shown that the new collimator designs made possible by new manufacturing techniques will

Measurement of the length and position of the lower oesophageal sphincter by correlation of external measurements and radiographic estimations in dogs

International Nuclear Information System (INIS)

Waterman, A.E.; Hashim, M.A.

1991-01-01

Fifty dogs were investigated in order to correlate the length and position of the lower oesophageal sphincter (LOS) with external measurements. Various external measurements were taken while the dogs were anaesthetised and positioned in lateral recumbency. An oesophageal tube was then introduced into the oesophagus and thoracic radiographs were taken. The 'real internal length of the oesophagus' was calculated as the length from the lower jaw incisor tooth to the position of the oesophageal tube at the costal border of the diaphragm. A highly significant linear correlation was found between this internal length and the external length from lower jaw incisor tooth to the anterior border of the head of the 10th rib. Using oesophageal manometry, the length and position of the LOS was also studied in 25 clinically normal bitches. The mean length of the LOS was found to be 4.6 +/- 0.92 cm. The position of the LOS was a mean of 4.4 +/- 1.69 cm cranial to the costal border of the diaphragm. The findings of this study indicate that the external measurements can be used to position catheters for accurate oesophageal manometry in the dog

Development of transient collisional excitation x-ray laser with ultra short-pulse laser

International Nuclear Information System (INIS)

Kado, Masataka; Kawachi, Tetsuya; Hasegawa, Noboru; Tanaka, Momoko; Sukegawa, Kouta; Nagashima, Keisuke; Kato, Yoshiaki

2001-01-01

We have observed lasing on Ne-like 3s-3p line from titanium (32.4 nm), Ni-like 4p-4d line from silver (13.9 nm) and tin (11.9 nm) with the transient collisional excitation (TCE) scheme that uses combination of a long pre-pulse (∼ns) and a short main pulse (∼ps). A gain coefficient of 23 cm -1 was measured for plasma length up to 4 mm with silver slab targets. We have also observed lasing on Ne-like and Ni-like lines with new TCE scheme that used pico-seconds laser pulse to generate plasma and observed strong improvement of x-ray laser gain coefficient. A gain coefficient of 14 cm -1 was measured for plasma length up to 6 mm with tin targets. (author)

Electron bunch length measurement at the Vanderbilt FEL

Energy Technology Data Exchange (ETDEWEB)

Amirmadhi, F.; Brau, C.A.; Mendenhall, M. [Vanderbilt Free-Electron-Laser Center, Nashville, TN (United States)] [and others

1995-12-31

During the past few years, a number of experiments have been performed to demonstrate the possibility to extract the longitudinal charge distribution from spectroscopic measurements of the coherent far-infrared radiation emitted as transition radiation or synchrotron radiation. Coherent emission occurs in a spectral region where the wavelength is comparable to or longer than the bunch length, leading to an enhancement of the radiation intensity that is on the order of the number of particles per bunch, as compared to incoherent radiation. This technique is particularly useful in the region of mm and sub-mm bunch lengths, a range where streak-cameras cannot be used for beam diagnostics due to their limited time resolution. Here we report on experiments that go beyond the proof of principle of this technique by applying it to the study and optimization of FEL performance. We investigated the longitudinal bunch length of the Vanderbilt FEL by analyzing the spectrum of coherent transition radiation emitted by the electron bunches. By monitoring the bunch length while applying a bunch-compression technique, the amount of the compression could be easily observed. This enabled us to perform a systematic study of the FEL performance, especially gain and optical pulse width, as a function of the longitudinal electron distribution in the bunch. The results of this study will be presented and discussed.

CM : becoming a technology firm

NARCIS (Netherlands)

Burg, van J.C.; Reymen, I.M.M.J.; Dolmans, S.A.M.

2011-01-01

Founded in 2000 as a Short Message Service (SMS) marketing company for discos (clubs), CM evolved into a technology provider for SMS services. By 2008, CM was market leader in The Netherlands, a position won by offering high quality services at low prices. In 2010, the founders of the company were

Appearance of a Minimal Length in $e^+ e^-$ Annihilation

CERN Document Server

Dymnikova, Irina; Ulbricht, Jürgen

2014-01-01

Experimental data reveal with a 5$\\sigma$ significance the existence of a characteristic minimal length $l_e$= 1.57 × 10$^{−17}$ cm at the scale E = 1.253 TeV in the annihilation reaction $e^+e^- \\to \\gamma\\gamma(\\gamma)$ . Nonlinear electrodynamics coupled to gravity and satisfying the weak energy condition predicts, for an arbitrary gauge invariant Lagrangian, the existence of spinning charged electromagnetic soliton asymptotically Kerr-Newman for a distant observer with the gyromagnetic ratio g=2 . Its internal structure includes a rotating equatorial disk of de Sitter vacuum which has properties of a perfect conductor and ideal diamagnetic, displays superconducting behavior, supplies a particle with the finite positive electromagnetic mass related to breaking of space-time symmetry, and gives some idea about the physical origin of a minimal length in annihilation.

Optimal design of similariton fiber lasers without gain-bandwidth limitation.

Science.gov (United States)

Li, Xingliang; Zhang, Shumin; Yang, Zhenjun

2017-07-24

We have numerically investigated broadband high-energy similariton fiber lasers, demonstrated that the self-similar evolution of pulses can locate in a segment of photonic crystal fiber without gain-bandwidth limitation. The effects of various parameters, including the cavity length, the spectral filter bandwidth, the pump power, the length of the photonic crystal fiber and the output coupling ratio have also been studied in detail. Using the optimal parameters, a single pulse with spectral width of 186.6 nm, pulse energy of 23.8 nJ, dechirped pulse duration of 22.5 fs and dechirped pulse peak power of 1.26 MW was obtained. We believe that this detailed analysis of the behaviour of pulses in the similariton regime may have major implications in the development of broadband high-energy fiber lasers.

Fundamental length and relativistic length

International Nuclear Information System (INIS)

Strel'tsov, V.N.

1988-01-01

It si noted that the introduction of fundamental length contradicts the conventional representations concerning the contraction of the longitudinal size of fast-moving objects. The use of the concept of relativistic length and the following ''elongation formula'' permits one to solve this problem

Select injury-related variables are affected by stride length and foot strike style during running.

Science.gov (United States)

Boyer, Elizabeth R; Derrick, Timothy R

2015-09-01

Some frontal plane and transverse plane variables have been associated with running injury, but it is not known if they differ with foot strike style or as stride length is shortened. To identify if step width, iliotibial band strain and strain rate, positive and negative free moment, pelvic drop, hip adduction, knee internal rotation, and rearfoot eversion differ between habitual rearfoot and habitual mid-/forefoot strikers when running with both a rearfoot strike (RFS) and a mid-/forefoot strike (FFS) at 3 stride lengths. Controlled laboratory study. A total of 42 healthy runners (21 habitual rearfoot, 21 habitual mid-/forefoot) ran overground at 3.35 m/s with both a RFS and a FFS at their preferred stride lengths and 5% and 10% shorter. Variables did not differ between habitual groups. Step width was 1.5 cm narrower for FFS, widening to 0.8 cm as stride length shortened. Iliotibial band strain and strain rate did not differ between foot strikes but decreased as stride length shortened (0.3% and 1.8%/s, respectively). Pelvic drop was reduced 0.7° for FFS compared with RFS, and both pelvic drop and hip adduction decreased as stride length shortened (0.8° and 1.5°, respectively). Peak knee internal rotation was not affected by foot strike or stride length. Peak rearfoot eversion was not different between foot strikes but decreased 0.6° as stride length shortened. Peak positive free moment (normalized to body weight [BW] and height [h]) was not affected by foot strike or stride length. Peak negative free moment was -0.0038 BW·m/h greater for FFS and decreased -0.0004 BW·m/h as stride length shortened. The small decreases in most variables as stride length shortened were likely associated with the concomitant wider step width. RFS had slightly greater pelvic drop, while FFS had slightly narrower step width and greater negative free moment. Shortening one's stride length may decrease or at least not increase propensity for running injuries based on the variables

An Analysis Nomoto Gain and Norbin Parameter on Ship Turning Maneuver

Directory of Open Access Journals (Sweden)

Aulia Siti Aisjah

2010-05-01

Full Text Available First order approach of maneuvering ship model developed by Nomoto, that has commonly underpinned researchers on mathematical models of ship maneuvering, is employed by the present research in order to describe the results of Nomoto validation gain value from some type of ships. In this present study, the controls are designated using FLC, while the rules are derived from FLC; furthermore, the reference is the LQG/LTR. On the other pole, Norbin parameters are obtained under the bases of the gain and time constant output control response. Validation of Nomoto gain value is obtained through the calculation of the value of a constant gain, settling time of the first order response, and approach value toward damping ratio and natural frequency response of the system used to control the output of the second order pattern. Validation is employed on 20 types of ships with a length between 40-350 meters; as a result, it is figured out that at the Low Speed General Cargo ship, Mariner, RO/RO, and Barge Carrier have good maneuverability compared to the other 17 types of ships.

Does hair coat length affect flea infestation in naturally infested dogs?

Science.gov (United States)

Silva, Guilherme Araujo Collares da; Lins, Luciana Araujo; Irala, Márcio Josué Costa; Cárcamo, Marcial Corrêa; Ribeiro, Paulo Bretanha

2016-01-01

The Siphonaptera are parasitic insects of endothermic animals and Ctenocephalides felis and Pulex irritans are important parasites of dogs. This study evaluated the effect of hair coat length and time of year on the population size of C. felis and P. irritans in naturally infested dogs. Fleas were collected from 14 dogs on a monthly basis for a year (February 2015 to January 2016) at a rural property in Bagé, Rio Grande do Sul, Brazil. The dogs were divided into two groups based on hair coat length: short coat (coat length coat (coat length > 5.0 cm, n= 7). In total, 2057 fleas were collected, 1541 of which were C. felis (74.91%) and 516 were P. irritans (25.08%). The number of C. felis and P. irritans individuals was significantly affected by hair coat length and time of year. The variation in flea numbers over the study months was higher in long-coated than in short-coated dogs for the two flea species and flea numbers increased with increasing mean monthly temperatures. The results provide a better understanding of behavioral aspects of flea communities in dogs and may help develop control strategies targeting these parasites.

Characterization and Schwann Cell Seeding of up to 15.0 cm Long Spider Silk Nerve Conduits for Reconstruction of Peripheral Nerve Defects

Directory of Open Access Journals (Sweden)

Tim Kornfeld

2016-11-01

Full Text Available Nerve reconstruction of extended nerve defect injuries still remains challenging with respect to therapeutic options. The gold standard in nerve surgery is the autologous nerve graft. Due to the limitation of adequate donor nerves, surgical alternatives are needed. Nerve grafts made out of either natural or artificial materials represent this alternative. Several biomaterials are being explored and preclinical and clinical applications are ongoing. Unfortunately, nerve conduits with successful enhancement of axonal regeneration for nerve defects measuring over 4.0 cm are sparse and no conduits are available for nerve defects extending to 10.0 cm. In this study, spider silk nerve conduits seeded with Schwann cells were investigated for in vitro regeneration on defects measuring 4.0 cm, 10.0 cm and 15.0 cm in length. Schwann cells (SCs were isolated, cultured and purified. Cell purity was determined by immunofluorescence. Nerve grafts were constructed out of spider silk from Nephila edulis and decellularized ovine vessels. Finally, spider silk implants were seeded with purified Schwann cells. Cell attachment was observed within the first hour. After 7 and 21 days of culture, immunofluorescence for viability and determination of Schwann cell proliferation and migration throughout the conduits was performed. Analyses revealed that SCs maintained viable (>95% throughout the conduits independent of construct length. SC proliferation on the spider silk was determined from day 7 to day 21 with a proliferation index of 49.42% arithmetically averaged over all conduits. This indicates that spider silk nerve conduits represent a favorable environment for SC attachment, proliferation and distribution over a distance of least 15.0 cm in vitro. Thus spider silk nerve implants are a highly adequate biomaterial for nerve reconstruction.

Microdose acquisition in adolescent leg length discrepancy using a low-dose biplane imaging system

DEFF Research Database (Denmark)

Jensen, Janni; Mussmann, Bo Redder; Hjarbæk, John

2017-01-01

To compare leg length measurements performed on diagnostic images and low dose preview images both acquired using a low-dose bi-planar imaging system. Material and Methods Preview and diagnostic images from 22 patients were retrospectively collected (14 girls, 8 boys; mean age, 12.8 years; age range, 10......-15 years). All images were anonymized and measured independently by two musculoskeletal radiologists. Three sets of measurements were performed on all images; the mechanical axis lines of the femur and the tibia as well as the anatomical line of the entire extremity. Statistical significance was tested...... with a paired t-test. Results No statistically significant difference was found between measurements performed on the preview and on the diagnostic image. The mean tibial length difference between the observers was -0.06 cm (95% confidence interval [CI], -0.12 to 0.01) and -0.08 cm (95% CI, -0.21 to 0...

Effect of Heating/Hydratation on Compacted Bentonite: Tests in 60-cm Long Cells

Energy Technology Data Exchange (ETDEWEB)

Villar, M. V.; Fernandez, A. M.; Martin, P. L.; Barcala, J. M.; Gomez-Espina, R.; Rivas, P.

2008-07-01

The conditions of the bentonite in an engineered barrier for high-level radioactive waste disposal have been simulated in a series of tests. Cylindrical cells with an inner length of 60 cm and a diameter of 7 cm were constructed. Inside the cells, blocks of compacted FEBEX bentonite were put one on top of the other. the bottom surface of the material was heated at 100 degree centigree and the top surface was injected with granitic water. the duration of the tests was 0.5, 1,2 and 7,6 years. The temperatures and water intake were measured during the tests and, at the end, the cells were dismounted and the dry density, water content, mineralogy, geochemistry and some hydro-mechanical properties of the clay (permeability, swelling) were measured at different positions. the values obtained are compared among them and to those of the untreated FEBEX bentonite. The study has run over for 10 years in the context of the projects FEBEX I and II and NF-PRO. (Author) 50 refs.

Effect of Heating/Hydratation on Compacted Bentonite: Tests in 60-cm Long Cells

International Nuclear Information System (INIS)

Villar, M. V.; Fernandez, A. M.; Martin, P. L.; Barcala, J. M.; Gomez-Espina, R.; Rivas, P.

2008-01-01

The conditions of the bentonite in an engineered barrier for high-level radioactive waste disposal have been simulated in a series of tests. Cylindrical cells with an inner length of 60 cm and a diameter of 7 cm were constructed. Inside the cells, blocks of compacted FEBEX bentonite were put one on top of the other. the bottom surface of the material was heated at 100 degree centigree and the top surface was injected with granitic water. the duration of the tests was 0.5, 1,2 and 7,6 years. The temperatures and water intake were measured during the tests and, at the end, the cells were dismounted and the dry density, water content, mineralogy, geochemistry and some hydro-mechanical properties of the clay (permeability, swelling) were measured at different positions. the values obtained are compared among them and to those of the untreated FEBEX bentonite. The study has run over for 10 years in the context of the projects FEBEX I and II and NF-PRO. (Author) 50 refs

Three-dimensional analysis of harmonic generation in high-gain free-electron lasers

International Nuclear Information System (INIS)

Huang, Zhirong; Kim, Kwang-Je

2000-01-01

In a high-gain free-electron laser (FEL) employing a planar undulator, strong bunching at the fundamental wavelength can drive substantial bunching and power levels at the harmonic frequencies. In this paper we investigate the three-dimensional evolution of harmonic radiation based on the coupled Maxwell-Klimontovich equations that take into account nonlinear harmonic interactions. Each harmonic field is a sum of a linear amplification term and a term driven by nonlinear harmonic interactions. After a certain stage of exponential growth, the dominant nonlinear term is determined by interactions of the lower nonlinear harmonics and the fundamental radiation. As a result, the gain length, transverse profile, and temporal structure of the first few harmonics are eventually governed by those of the fundamental. Transversely coherent third-harmonic radiation power is found to approach 1% of the fundamental power level for current high-gain FEL projects

The CIRENE program: experience gained in development of technology

International Nuclear Information System (INIS)

Villani, A.

1982-01-01

The construction of the Cirene 40 MW prototype electrical power plant at Latina is the main objective of the Cirene development program. A plant contract was given to NIRA at the end of 1976, and the plant completion is foreseen by the end of 1984. The Cirene is a heavy water-moderated, natural uranium-fueled pressure-tube reactor using boiling light water as the primary coolant. The design of Cirene is outlined. The numbers of pressure tubes, calandria tubes, liquid rod tubes and regulating rod tubes are 60, 60, 10 and 4, respectively, all made of Zircaloy-2. The equivalent diameter, length and lattice pitch of the core are 236 cm, 400 cm and 27 cm, respectively. The heavy water tank has the central zone of I.D. 369 cm and the dump annulus of I.D. 520 cm, made of AISI 304 L. These key parameters are shown. The means of regulating radioactivity during the normal operation of the reactor are: the two-phase rods, the level of the moderator and the concentration of boron in moderator. The function of two-phase rod regulation system is to introduce a variable density two-phase mixture consisting of boric acid solution and nonabsorbent gas in the core. The R and D was conducted to assess the functional and dynamic features of this control system. The plant is equipped with two independent fast-acting scram systems, discharging of moderator and liquid-rod system. The pressure-tube rupture test was carried out. (Nakai, Y.)

Accuracy of free energies of hydration using CM1 and CM3 atomic charges.

Science.gov (United States)

Udier-Blagović, Marina; Morales De Tirado, Patricia; Pearlman, Shoshannah A; Jorgensen, William L

2004-08-01

Absolute free energies of hydration (DeltaGhyd) have been computed for 25 diverse organic molecules using partial atomic charges derived from AM1 and PM3 wave functions via the CM1 and CM3 procedures of Cramer, Truhlar, and coworkers. Comparisons are made with results using charges fit to the electrostatic potential surface (EPS) from ab initio 6-31G* wave functions and from the OPLS-AA force field. OPLS Lennard-Jones parameters for the organic molecules were used together with the TIP4P water model in Monte Carlo simulations with free energy perturbation theory. Absolute free energies of hydration were computed for OPLS united-atom and all-atom methane by annihilating the solutes in water and in the gas phase, and absolute DeltaGhyd values for all other molecules were computed via transformation to one of these references. Optimal charge scaling factors were determined by minimizing the unsigned average error between experimental and calculated hydration free energies. The PM3-based charge models do not lead to lower average errors than obtained with the EPS charges for the subset of 13 molecules in the original study. However, improvement is obtained by scaling the CM1A partial charges by 1.14 and the CM3A charges by 1.15, which leads to average errors of 1.0 and 1.1 kcal/mol for the full set of 25 molecules. The scaled CM1A charges also yield the best results for the hydration of amides including the E/Z free-energy difference for N-methylacetamide in water. Copyright 2004 Wiley Periodicals, Inc.

On the gain properties of “thin” elastically strained InGaAs/InGaAlAs quantum wells emitting in the near-infrared spectral region near 1550 nm

Energy Technology Data Exchange (ETDEWEB)

Novikov, I. I.; Karachinsky, L. Ya. [Connector Optics LLC (Russian Federation); Kolodeznyi, E. S.; Bougrov, V. E. [National Research University of Information Technologies, Mechanics and Optics (Russian Federation); Kurochkin, A. S.; Gladyshev, A. G.; Babichev, A. V. [Connector Optics LLC (Russian Federation); Gadzhiev, I. M.; Buyalo, M. S. [National Research University of Information Technologies, Mechanics and Optics (Russian Federation); Zadiranov, Yu. M.; Usikova, A. A., E-mail: anton@beam.ioffe.ru; Shernyakov, Yu. M. [Russian Academy of Sciences, Ioffe Physical–Technical Institute (Russian Federation); Savelyev, A. V.; Nyapshaev, I. A. [National Research University of Information Technologies, Mechanics and Optics (Russian Federation); Egorov, A. Yu. [Connector Optics LLC (Russian Federation)

2016-10-15

The results of experimental studies of the gain properties of “thin” (3.2 nm thick) elastically strained InGaAs/InGaAlAs quantum wells emitting in the near-infrared spectral region near 1550 nm are presented. The results of studying the threshold and gain characteristics of stripe laser diodes with active regions based on “thin” quantum wells with a lattice–substrate mismatch of +1.0% show that the quantum wells under study exhibit a high modal gain of 11 cm{sup –1} and a low transparency current density of 46 A/cm{sup 2} per quantum well.

Near field imaging of transient collisional excitation x-ray laser

International Nuclear Information System (INIS)

Tanaka, Momoko; Kado, Masataka; Hasegawa, Noboru; Kawachi, Tetsuya; Sukegawa, Kouta; Lu, Peixiang; Nagashima, Akira; Kato, Yoshiaki

2001-01-01

We observed the spatial profile of the transient collisional excitation Ni-like Ag laser (λ=13.9 nm) for various plasma lengths using the near field imaging method. The gain coefficient of the x-ray laser was estimated as 24 cm -1 . The gain region was a 50 μm crescent shape and included localized high gain areas. (author)

Newborn length predicts early infant linear growth retardation and disproportionately high weight gain in a low-income population.

Science.gov (United States)

Berngard, Samuel Clark; Berngard, Jennifer Bishop; Krebs, Nancy F; Garcés, Ana; Miller, Leland V; Westcott, Jamie; Wright, Linda L; Kindem, Mark; Hambidge, K Michael

2013-12-01

Stunting is prevalent by the age of 6 months in the indigenous population of the Western Highlands of Guatemala. The objective of this study was to determine the time course and predictors of linear growth failure and weight-for-age in early infancy. One hundred and forty eight term newborns had measurements of length and weight in their homes, repeated at 3 and 6 months. Maternal measurements were also obtained. Mean ± SD length-for-age Z-score (LAZ) declined from newborn -1.0 ± 1.01 to -2.20 ± 1.05 and -2.26 ± 1.01 at 3 and 6 months respectively. Stunting rates for newborn, 3 and 6 months were 47%, 53% and 56% respectively. A multiple regression model (R(2) = 0.64) demonstrated that the major predictor of LAZ at 3 months was newborn LAZ with the other predictors being newborn weight-for-age Z-score (WAZ), gender and maternal education∗maternal age interaction. Because WAZ remained essentially constant and LAZ declined during the same period, weight-for-length Z-score (WLZ) increased from -0.44 to +1.28 from birth to 3 months. The more severe the linear growth failure, the greater WAZ was in proportion to the LAZ. The primary conclusion is that impaired fetal linear growth is the major predictor of early infant linear growth failure indicating that prevention needs to start with maternal interventions. © 2013.

Short initial length quench on CICC of ITER TF coils

Energy Technology Data Exchange (ETDEWEB)

Nicollet, S.; Ciazynski, D.; Duchateau, J.-L.; Lacroix, B. [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Bessette, D.; Rodriguez-Mateos, F. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Coatanea-Gouachet, M. [ELC Engineering, 350 chemin du Verladet, F-13290 Les Milles (France); Gauthier, F. [Soditech Ingenierie, 4 bis allée des Gabians, ZI La Frayère, 06150 Cannes (France)

2014-01-29

Previous quench studies performed for the International Thermonuclear Experimental Reactor (ITER) Toroidal Field (TF) Coils have led to identify two extreme families of quench: first 'severe' quenches over long initial lengths in high magnetic field, and second smooth quenches over short initial lengths in low field region. Detailed analyses and results on smooth quench propagation and detectability on one TF Cable In Conduit Conductor (CICC) with a lower propagation velocity are presented here. The influence of the initial quench energy is shown and results of computations with either a Fast Discharge (FD) of the magnet or without (failure of the voltage quench detection system) are reported. The influence of the central spiral of the conductor on the propagation velocity is also detailed. In the cases of a regularly triggered FD, the hot spot temperature criterion of 150 K (with helium and jacket) is fulfilled for an initial quench length of 1 m, whereas this criterion is exceed (Tmax ≈ 200 K) for an extremely short length of 5 cm. These analyses were carried out using both the Supermagnet(trade mark, serif) and Venecia codes and the comparisons of the results are also discussed.

Short initial length quench on CICC of ITER TF coils

International Nuclear Information System (INIS)

Nicollet, S.; Ciazynski, D.; Duchateau, J.-L.; Lacroix, B.; Bessette, D.; Rodriguez-Mateos, F.; Coatanea-Gouachet, M.; Gauthier, F.

2014-01-01

Previous quench studies performed for the International Thermonuclear Experimental Reactor (ITER) Toroidal Field (TF) Coils have led to identify two extreme families of quench: first 'severe' quenches over long initial lengths in high magnetic field, and second smooth quenches over short initial lengths in low field region. Detailed analyses and results on smooth quench propagation and detectability on one TF Cable In Conduit Conductor (CICC) with a lower propagation velocity are presented here. The influence of the initial quench energy is shown and results of computations with either a Fast Discharge (FD) of the magnet or without (failure of the voltage quench detection system) are reported. The influence of the central spiral of the conductor on the propagation velocity is also detailed. In the cases of a regularly triggered FD, the hot spot temperature criterion of 150 K (with helium and jacket) is fulfilled for an initial quench length of 1 m, whereas this criterion is exceed (Tmax ≈ 200 K) for an extremely short length of 5 cm. These analyses were carried out using both the Supermagnet(trade mark, serif) and Venecia codes and the comparisons of the results are also discussed

Small-signal modulation and differential gain of red-emitting (λ = 630 nm) InGaN/GaN quantum dot lasers

Energy Technology Data Exchange (ETDEWEB)

Frost, Thomas; Banerjee, Animesh; Bhattacharya, Pallab, E-mail: pkb@eecs.umich.edu [Department of Electrical Engineering and Computer Science, University of Michigan, Ann Arbor, Michigan 48109-2122 (United States)

2013-11-18

We report small-signal modulation bandwidth and differential gain measurements of a ridge waveguide In{sub 0.4}Ga{sub 0.6}N/GaN quantum dot laser grown by molecular beam epitaxy. The laser peak emission is at λ = 630 nm. The −3 dB bandwidth of an 800 μm long device was measured to be 2.4 GHz at 250 mA under pulsed biasing, demonstrating the possibility of high-speed operation of these devices. The differential gain was measured to be 5.3 × 10{sup −17} cm{sup 2}, and a gain compression factor of 2.87 × 10{sup −17} cm{sup 3} is also derived from the small-signal modulation response.

Positive gain measurements on the 3350-A continuum band of Hg2

International Nuclear Information System (INIS)

Schlie, L.A.; Guenther, B.D.; Rathge, R.D.

1976-01-01

A He-Cd + laser operating at 3250 A and an Ar + laser at 3511 A and 3638 A have been used to probe for gain on both sides of the Hg 2 3350-A (A 3 1/subu/→X 1 Σ/subg/ + ) continuum band in Hg vapor at a pressure of 3.75 atm that was pumped by a 1.5-MeV 600-J 20-ns electron beam. This letter presents the first observation of positive gain on this 3350-A band of Hg 2 . The results indicate that the stimulated emission cross section for this band is larger than any associated photoionization process in the Hg vapor and has a magnitude of approximately 10 -18 cm 2 . Also, raising the temperature of the vapor above its saturation value increases the maximum value and duration of the observed gain, indicating that the population of the upper level of this transition is being fed by a temperature-dependent internal energy reservoir in the Hg

Calorimetric determination of kQ factors for NE 2561 and NE 2571 ionization chambers in 5 cm x 5 cm and 10 cm x 10 cm radiotherapy beams of 8 MV and 16 MV photons.

Science.gov (United States)

Krauss, Achim; Kapsch, Ralf-Peter

2007-10-21

The relative uncertainty of the ionometric determination of the absorbed dose to water, D(w), in the reference dosimetry of high-energy photon beams is in the order of 1.5% and is dominated by the uncertainty of the calculated chamber- and energy-dependent correction factors k(Q). In the present investigation, k(Q) values were determined experimentally in 5 cm x 5 cm and 10 cm x 10 cm radiotherapy beams of 8 MV and 16 MV bremsstrahlung by means of a water calorimeter operated at 4 degrees C. Ionization chambers of the types NE 2561 and NE 2571 were calibrated directly in the water phantom of the calorimeter. The measurements were carried out at the linear accelerator of the Physikalisch-Technische Bundesanstalt. It is shown that the k(Q) factor of a single ionization chamber can be measured with a standard uncertainty of less than 0.3%. No significant variations of k(Q) were found for the different lateral sizes of the radiation fields used in this investigation.

A New Formula to Estimate the Length of Right Upper Extremity Vein from Elbow Crease to Carina Calculated by Peripherally Inserted Central Catheter Insertion through Right Basilic Vein Puncture

International Nuclear Information System (INIS)

Cho, Hyun Hwan; Jeon, Eui Yong; Lee, Hyun Jung; Lee, Hyun; Koh, Sung Hye; Choi, Sun Young; Lee, Kwan Seop; Yoon, Dae Young; Im, Hyoung June

2012-01-01

To measure the length of the upper extremity vein between the elbow crease and the carina (elbow crease to carina length, ECL), to facilitate the appropriate positioning of the tip of the peripherally inserted central catheter (PICC). A total of 124 patients (64 men and 60 women; mean age 65.2 ± 15.4 years; range, 21-90 years) inserted with PICC through the right basilic vein under fluoroscopy were included in this retrospective study. The ECL was determined as follows: ECL = (distance from elbow crease to puncture site) + (the catheter length of PICC) - (distance from carina to catheter tip on post-procedural chest radiograph). We analyzed the relationship between ECL and patient height. The mean ECL through right basilic vein was 42.07 ±4.03 cm (27.5 to 52.2 cm). ECL was found to be significantly correlated with patient height: ECL (cm) = 0.24 X patient height (cm) + 3.75. The formula developed in our study would be helpful for predicting the optimal catheter length during a blind bedside procedure of PICC via the right basilic vein.

Associations between adiposity, hormones, and gains in height, whole-body height-adjusted bone size, and size-adjusted bone mineral content in 8- to 11-year-old children.

Science.gov (United States)

Dalskov, S; Ritz, C; Larnkjær, A; Damsgaard, C T; Petersen, R A; Sørensen, L B; Ong, K K; Astrup, A; Michaelsen, K F; Mølgaard, C

2016-04-01

We examined fat-independent associations of hormones with height and whole-body bone size and mineral content in 633 school children. IGF-1 and osteocalcin predict growth in height, while fat, osteocalcin, and in girls also, IGF-1 predict growth in bone size. Leptin and ghrelin are inversely associated with bone size in girls. Obesity causes larger bone size and bone mass, but the role of hormones in this up-regulation of bone in obesity is not well elucidated. We examined longitudinal associations between baseline body fat mass (FM), and fat-independent fasting levels of ghrelin, adiponectin, leptin, insulin, insulin-like growth factor-I (IGF-1), osteocalcin, and intact parathyroid hormone, and subsequent changes in height and in whole-body height-adjusted bone area "BAheight" and size-adjusted bone mineral content "BMCsize" in 8- to 11-year-olds. Analyses were carried out separately for boys (n = 325) and girls (n = 308) including data from baseline, 3 and 6 months from OPUS School Meal Study. In both sexes: gain in BAheight was positively associated with baseline FM (≥2.05 cm(2)/kg, both p ≤ 0.003). Furthermore, gain in height was positively associated with baseline IGF-1 (≥0.02 cm/ng/ml, p = 0.001) and osteocalcin (≥0.13 cm/ng/ml, p ≤ 0.009); and gain in BAheight was positively associated with baseline osteocalcin (≥0.35 cm(2)/ng/ml, p ≤ 0.019). In girls only, gain in BAheight was also positively associated with baseline IGF-1 (0.06 cm(2)/ng/ml, p = 0.017) and inversely associated with both baseline ghrelin (-0.01 cm(2)/pg/ml, p = 0.001) and leptin (-1.21 cm(2)/μg/ml, p = 0.005). In boys, gain in BMCsize was positively associated with osteocalcin (0.18 g/ng/ml, p = 0.030). This large longitudinal study suggests that in 8- to 11-year-old children, IGF-1 and osteocalcin predict growth in height, while FM, osteocalcin, and in girls also, IGF-1 predict growth in BAheight. Fat-independent inverse

Experimental studies of x-ray laser spectral profiles: Observation of gain narrowing and saturation behavior

International Nuclear Information System (INIS)

Koch, J.A.; MacGowan, B.J.; Da Silva, L.B.; Matthews, D.L.; Mrowka, S.; Underwood, J.H.; Batson, P.J.

1992-01-01

We discuss our recent measurements of the spectral width of the 206.38 Angstrom x-ray laser transition in Ne-like Se. These measurements used a high-resolution grating spectrometer and were performed over a wide range of laser amplifier lengths. The data have enabled us to extrapolate the intrinsic line width and to observe the effects of gain-narrowing and saturation on the line profile. We find an intrinsic width which is 1.4 times the Doppler width, we observe gain-narrowing in intermediate length amplifiers, and we observe no re-broadening in long, saturated amplifiers. These results suggest that collisional line-broadening has a significant effect on the line profile and saturation behavior of this laser. We discuss modeling we have performed in order to simulate the experimental data, and we discuss future experimental and theoretical efforts we believe are necessary in order to understand line broadening and line transfer issues in x-ray laser plasmas

Early Weight Gain, Linear Growth, and Mid-Childhood Blood Pressure

DEFF Research Database (Denmark)

Perng, Wei; Rifas-Shiman, Sheryl L; Kramer, Michael S

2016-01-01

of gains in body mass index z-score and length/height z-score during 4 early life age intervals (birth to 6 months, 6 months to 1 year, 1 to 2 years, and 2 to 3 years) with blood pressure during mid-childhood (6-10 years) and evaluated whether these relations differed by birth size. After accounting....... Strategies to reduce accrual of excess adiposity during early life may reduce mid-childhood blood pressure, which may also impact adult blood pressure and cardiovascular health....

Reducing liver transplant length of stay: a Lean Six Sigma approach.

Science.gov (United States)

Toledo, Alexander H; Carroll, Tracy; Arnold, Emily; Tulu, Zeynep; Caffey, Tom; Kearns, Lauren E; Gerber, David A

2013-12-01

Organ transplant centers are under increasing scrutiny to maintain outcomes while controlling cost in a challenging population of patients. Throughout health care and transplant specifically, length of stay is used as a benchmark for both quality and resource utilization. To decrease our length of stay for liver transplant by using Lean Six Sigma methods. The Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) method was used to systematically analyze our process from transplant listing to hospital discharge after transplant, identifying many factors affecting length of stay. Adult, single-organ, primary liver transplant recipients between July 2008 and June 2012 were included in the study. Recipients with living donors or fulminant liver failure were excluded. Multiple interventions, including a clinical pathway and enhanced communication, were implemented. Length of stay after liver transplant and readmission after liver transplant.R ESULTS: Median length of stay decreased significantly from 11 days before the intervention to 8 days after the intervention. Readmission rate did not change throughout the study. The improved length of stay was maintained for 24 months after the study. Using a Lean Six Sigma approach, we were able to significantly decrease the length of stay of liver transplant patients. These results brought our center's outcomes in accordance with our goal and industry benchmark of 8 days. Clear expectations, improved teamwork, and a multidisciplinary clinical pathway were key elements in achieving and maintaining these gains.

Relationships between total length and otolith size of bluefish Pomatomus saltatrix (Linnaeus, 1766 in the Marmara Sea of Turkey

Directory of Open Access Journals (Sweden)

Habib Bal

2018-01-01

Full Text Available In the present study, bluefish, Pomatomus saltatrix, was monthly collected from commercial fishing boats operating in the Marmara Sea between January and December 2014. The relationship between total length and otolith size of 346 bluefish samples were examined. Total lengths of females, males and unidentified samples were ranged from between 13.2-37.0, 12.3-34.8 and 13.0-31.6 cm, respectively. Otolith lengths were between 3.82-12.60 mm and otolith width were between 1.59-4.34 mm for all samples. It was found that there is a strong correlations between otolith length-total length (r2 =0.88 and otolith width-total length (r2 0.81.

Operation of a Five-Stage 40,000-CM2-Area Insulator Stack at 158 KV/CM

International Nuclear Information System (INIS)

Anderson RA; Clark, Robert E; Corcoran, PA; Douglas, John W; Gilliland, TL; Horry, ML; Hughes, Thomas P; Ives, HC; Long, FW; Martin, TH; McDaniel, DH; Milton, Osborne; Mostrom, Michael A; Seamen, JF; Shoup, RW; Smith, ID; Smith, JW; Spielman, RB; Struve, KW; Stygar, WA; Vogtlin, George E; Wagoner, TC; Yamamoto, Osamu

1999-01-01

We have demonstrated successful operation of a 3.35- m-diameter insulator stack at 158 kV/cm on five consecutive Z-accelerator shots. The stack consisted of five +45 deg;-profile 5.715-cm-thick cross-linked-polystyrene (Rexolite- 1422) insulator rings, and four anodized- aluminum grading rings shaped to reduce the field at cathode triple junctions. The width of the voltage pulse at 89% of peak was 32 ns. We compare this result to a new empirical flashover relation developed from previous small-insulator experiments conducted with flat unanodized electrodes. The relation predicts a 50% flashover probability for a Rexolite insulator during an applied voltage pulse when E max e -0.27/d (t eff C) 1/10 = 224, where E max is the peak mean electric field (kV/cm), d is the insulator thickness (cm), t eff is the effective pulse width (ps), and C is the insulator circumference (cm). We find the Z stack can be operated at a stress at least 19% higher than predicted. This result, and previous experiments conducted by Vogtlin, suggest anodized electrodes with geometries that reduce the field at both anode and cathode triple junctions would improve the flashover strength of +45 deg; insulators

Noise Induces Biased Estimation of the Correction Gain.

Directory of Open Access Journals (Sweden)

Jooeun Ahn

Full Text Available The detection of an error in the motor output and the correction in the next movement are critical components of any form of motor learning. Accordingly, a variety of iterative learning models have assumed that a fraction of the error is adjusted in the next trial. This critical fraction, the correction gain, learning rate, or feedback gain, has been frequently estimated via least-square regression of the obtained data set. Such data contain not only the inevitable noise from motor execution, but also noise from measurement. It is generally assumed that this noise averages out with large data sets and does not affect the parameter estimation. This study demonstrates that this is not the case and that in the presence of noise the conventional estimate of the correction gain has a significant bias, even with the simplest model. Furthermore, this bias does not decrease with increasing length of the data set. This study reveals this limitation of current system identification methods and proposes a new method that overcomes this limitation. We derive an analytical form of the bias from a simple regression method (Yule-Walker and develop an improved identification method. This bias is discussed as one of other examples for how the dynamics of noise can introduce significant distortions in data analysis.

Satellite-based climate data records of surface solar radiation from the CM SAF

Science.gov (United States)

Trentmann, Jörg; Cremer, Roswitha; Kothe, Steffen; Müller, Richard; Pfeifroth, Uwe

2017-04-01

The incoming surface solar radiation has been defined as an essential climate variable by GCOS. Long term monitoring of this part of the earth's energy budget is required to gain insights on the state and variability of the climate system. In addition, climate data sets of surface solar radiation have received increased attention over the recent years as an important source of information for solar energy assessments, for crop modeling, and for the validation of climate and weather models. The EUMETSAT Satellite Application Facility on Climate Monitoring (CM SAF) is deriving climate data records (CDRs) from geostationary and polar-orbiting satellite instruments. Within the CM SAF these CDRs are accompanied by operational data at a short time latency to be used for climate monitoring. All data from the CM SAF is freely available via www.cmsaf.eu. Here we present the regional and the global climate data records of surface solar radiation from the CM SAF. The regional climate data record SARAH (Surface Solar Radiation Dataset - Heliosat, doi: 10.5676/EUM_SAF_CM/SARAH/V002) is based on observations from the series of Meteosat satellites. SARAH provides 30-min, daily- and monthly-averaged data of the effective cloud albedo, the solar irradiance (incl. spectral information), the direct solar radiation (horizontal and normal), and the sunshine duration from 1983 to 2015 for the full view of the Meteosat satellite (i.e, Europe, Africa, parts of South America, and the Atlantic ocean). The data sets are generated with a high spatial resolution of 0.05° allowing for detailed regional studies. The global climate data record CLARA (CM SAF Clouds, Albedo and Radiation dataset from AVHRR data, doi: 10.5676/EUM_SAF_CM/CLARA_AVHRR/V002) is based on observations from the series of AVHRR satellite instruments. CLARA provides daily- and monthly-averaged global data of the solar irradiance (SIS) from 1982 to 2015 with a spatial resolution of 0.25°. In addition to the solar surface

Genetic gains in physic nut using selection indexes

Directory of Open Access Journals (Sweden)

Leonardo Lopes Bhering

2012-03-01

Full Text Available The objective of this work was to estimate genetic gains in physic nut (Jatropha curcas using selection indexes and to establish the best selection strategy for the species. Direct and indirect selection was carried out using different selection indexes, totalizing 14 strategies. One hundred and seventy five families from the active germplasm bank of Embrapa Agroenergy, Brasília, Brazil, were analyzed in a randomized complete block design with two replicates. The evaluated traits were: grain yield; seeds per fruit; endosperm/seed ratio; seed weight, length, width, and thickness; branches per plant at 0.5, 1.0, and 1.5 m; plant height; stem diameter; canopy projection on rows and between lines; canopy volume; juvenility (days to the first flowering; and height of the first inflorescence. Evaluations were done during the second year of cultivation. The use of selection indexes is relevant to maximize the genetic gains in physic nut, favoring a better distribution of desirable traits. The multiplicative and restrictive indexes are considered the most promising for selection.

Progress in laboratory high gain ICF [inertial confinement fusion]: Prospects for the future

International Nuclear Information System (INIS)

Storm, E.; Lindl, J.D.; Campbell, E.M.

1988-01-01

Inertial confinement fusion (ICF), a thermonuclear reaction in a small (/approximately/5 mm diameter) fuel capsule filled with a few milligrams of deuterium and tritium, has been the subject of very fruitful experimentation since the early 1970's. High gain ICF is now on the threshold of practical applications. With a Laboratory Microfusion Facility (LMF), these applications will have major implications for national defense, basic and applied science, and power production. With a driver capable of delivering about 10 MJ in a 10-ns pulse at an intensity of /approximately/3 /times/ 10 14 W/cm 2 , an appropriately configured cryogenic capsule could be compressed to a density of about 200 g/cm 3 and a temperature of 3--5 keV. Under these conditions, up to 10 mg of DT could be ignited, and with a burn efficiency of about 30%, release up to 1000 MJ of fusion energy, an energy gain of about 100. A thousand megajoules is equivalent to about one quarter ton of TNT, or about 7 gallons of oil--an amount of energy tractable under laboratory conditions and potentially very useful for a variety of applications. 61 refs., 33 figs

High-gain polymer optical waveguide amplifiers based on core-shell NaYF4/NaLuF4: Yb3+, Er3+ NPs-PMMA covalent-linking nanocomposites

Science.gov (United States)

Zhang, Meiling; Zhang, Weiwei; Wang, Fei; Zhao, Dan; Qu, Chunyang; Wang, Xibin; Yi, Yunji; Cassan, Eric; Zhang, Daming

2016-11-01

Waveguide amplifiers have always been significant key components for optical communication. Unfortunately, the low concentration of rare earth ions doped in the host material and the inadequate optimization of the waveguide structure have been the common bottleneck limitations. Here, a novel material, NaYF4/NaLuF4: 20% Yb3+, 2% Er3+ nanoparticle-Polymeric Methyl Methacrylate covalent-linking nanocomposite, was synthesized. The concentrations of Er3+ and Yb3+ doping increased an order of magnitude. Under a 980 nm laser excitation, highly efficient emission at 1.53 μm was obtained. The characteristic parameters of the single mode waveguide were carefully designed and optimized by using a finite difference method. A formulized iteration method is presented for solving the rate equations and the propagation equations of the EYCDWA, and both the steady state behavior and the gain were numerically simulated. The optimal Er3+ and Yb3+ concentrations are 2.8 × 1026 m-3 and 2.8 × 1027 m-3, and the optimal waveguide length is 1.3 cm. Both theoretical and experimental results indicated that, for an input signal power of 0.1 mW and a pump power of 400 mW, a net gain of 15.1 dB at 1530 nm is demonstrated. This result is the highest gain ever reported in polymer-based waveguide amplifiers doped with inorganic Er3+-Yb3+ codoped nanocrystals.

Two independent measurements of Debye lengths in doped nonpolar liquids.

Science.gov (United States)

Prieve, D C; Hoggard, J D; Fu, R; Sides, P J; Bethea, R

2008-02-19

Electric current measurements were performed between 2.5 cm x 7.5 cm parallel-plate electrodes separated by 1.2 mm of heptane doped with 0-15% w/w poly(isobutylene succinimide) (PIBS) having a molecular weight of about 1700. The rapid (microsecond) initial charging of the capacitor can be used to infer the dielectric constant of the solution. The much slower decay of current arising from the polarization of electrodes depends on the differential capacitance of the diffuse clouds of charge carriers accumulating next to each electrode and on the ohmic resistance of the fluid. Using the Gouy-Chapman model for the differential capacitance, Debye lengths of 80-600 nm were deduced that decrease with increasing concentration of PIBS. Values of the Debye lengths were confirmed by performing independent measurements of double-layer repulsion between a 6 microm polystyrene (PS) latex sphere and a PS-coated glass plate using total internal reflection microscopy in the same solutions. The charge carriers appear to be inverted PIBS micelles having apparent Stokes diameters of 20-40 nm. Dynamic light scattering reveals a broad distribution of sizes having an intensity-averaged diameter of 15 nm. This smaller size might arise (1) from overestimating the electrophoretic mobility of micelles by treating them as point charges or (2) because charged micelles are larger on average than uncharged micelles. When Faradaic reactions and zeta potentials on the electrodes can be neglected, such current versus time experiments yield values for the Debye length and ionic strength with less effort than force measurements. To obtain the concentration of charge carriers from measurements of conductivity, the mobility of the charge carriers must be known.

Genetic gain for body weight, feed conversion and carcass traits in selected broiler strains

Directory of Open Access Journals (Sweden)

GS Schmidt

2006-03-01

Full Text Available The Brazilian Swine and Poultry Research Center (Embrapa Suínos e Aves maintains a chicken breeding program for meat production since 1985. Two control lines (LLc and PPc are maintained, whereas two male lines (TT and ZZ and three female lines (PP, VV and KK have been selected. This paper reports the genetic gain after 15 generations of combined selection (mass and independent culling levels in order to develop the commercial broiler stocks Embrapa 021 and Embrapa 022. Selection pressure has been exerted on weight gain, carcass traits and fertility. In addition, female lines have also been selected for egg production, whereas males have been selected for feed efficiency since 1992. All lines have been selected for breast area instead of carcass traits since 1999. The genetic gain was estimated as the deviation between selected lines and the respective unselected lines at 42 days of age. In female lines, body weight improved 504, 548 and 587 g; average breast area increased 27.60; 16.99 and 26.43 cm²; adjusted feed conversion (42-49 d improved -1.46; -0.97 and 1.76 units, and egg production varied 6.99; 7.12 and -3.43% units for PP, VV and KK, respectively. In male lines, body weight improved 758 and 408 g; average breast area increased 31.95 and 19.38 cm², and adjusted feed conversion improved (42-49 d -0.99 and 1.26 for TT and ZZ, respectively. This breeding program has been effective to generate genetic gain and to develop two commercial products, Embrapa 021 (standard and Embrapa 022 (high yield. Nevertheless, feed efficiency is still not satisfactory.

A case of 45,X/47,XXX mosaic Turner syndrome with limb length discrepancy.

Science.gov (United States)

Hishimura-Yonemaru, Nozomi; Okuhara, Koji; Takahashi, Nobuhiro; Tonoki, Hidefumi; Iizuka, Susumu; Tajima, Toshihiro

2017-01-01

Patients with Turner syndrome (TS) frequently show short stature and skeletal deformities, such as kyphosis and scoliosis. However, to the best of our knowledge, limb length discrepancy (LLD) has not yet been reported in patients with TS. The case of a 12-yr-old girl with 45,X/47,XXX mosaic TS showing LLD is herein presented. She was on GH therapy for short stature and was noted to have scoliosis in the standing position at a regular examination; however, the scoliosis became less evident in the supine position, which is indicative of LLD. The length of the left leg was 5.0 cm shorter than that of the right leg when measured. She was referred to orthopedics and underwent right distal femoral and right proximal tibial staple epiphysiodesis to shorten the abnormally long limb at 10 yr 6 mo of age. One year after the operation, the LLD decreased from 5.0 to 1.5 cm. During this period, GH was continued. LLD is a rare complication in TS, but when patients with TS show scoliosis in the standing position, re-evaluation for scoliosis in the supine position should be performed and the lengths of both legs should be measured.

Genetic deletion of muscle RANK or selective inhibition of RANKL is not as effective as full-length OPG-fc in mitigating muscular dystrophy.

Science.gov (United States)

Dufresne, Sébastien S; Boulanger-Piette, Antoine; Bossé, Sabrina; Argaw, Anteneh; Hamoudi, Dounia; Marcadet, Laetitia; Gamu, Daniel; Fajardo, Val A; Yagita, Hideo; Penninger, Josef M; Russell Tupling, A; Frenette, Jérôme

2018-04-24

Although there is a strong association between osteoporosis and skeletal muscle atrophy/dysfunction, the functional relevance of a particular biological pathway that regulates synchronously bone and skeletal muscle physiopathology is still elusive. Receptor-activator of nuclear factor κB (RANK), its ligand RANKL and the soluble decoy receptor osteoprotegerin (OPG) are the key regulators of osteoclast differentiation and bone remodelling. We thus hypothesized that RANK/RANKL/OPG, which is a key pathway for bone regulation, is involved in Duchenne muscular dystrophy (DMD) physiopathology. Our results show that muscle-specific RANK deletion (mdx-RANK mko ) in dystrophin deficient mdx mice improves significantly specific force [54% gain in force] of EDL muscles with no protective effect against eccentric contraction-induced muscle dysfunction. In contrast, full-length OPG-Fc injections restore the force of dystrophic EDL muscles [162% gain in force], protect against eccentric contraction-induced muscle dysfunction ex vivo and significantly improve functional performance on downhill treadmill and post-exercise physical activity. Since OPG serves a soluble receptor for RANKL and as a decoy receptor for TRAIL, mdx mice were injected with anti-RANKL and anti-TRAIL antibodies to decipher the dual function of OPG. Injections of anti-RANKL and/or anti-TRAIL increase significantly the force of dystrophic EDL muscle [45% and 17% gains in force, respectively]. In agreement, truncated OPG-Fc that contains only RANKL domains produces similar gains, in terms of force production, than anti-RANKL treatments. To corroborate that full-length OPG-Fc also acts independently of RANK/RANKL pathway, dystrophin/RANK double-deficient mice were treated with full-length OPG-Fc for 10 days. Dystrophic EDL muscles exhibited a significant gain in force relative to untreated dystrophin/RANK double-deficient mice, indicating that the effect of full-length OPG-Fc is in part independent of the RANKL

Scaling of gain with energy spread and energy in the PEP FEL

International Nuclear Information System (INIS)

Fisher, A.S.

1992-01-01

The Sag Harbor paper on the PEP FEL discusses the scaling of various FEL parameters with energy spread σ var-epsilon . I will repeat some of this material here and then examine the benefit of increasing the energy spread. How much energy spread can be achieved with damping wigglers is the next topic. Finally, I consider the dependence of gain and saturation length on beam energy and undulator field

Leveraging the NLM map from SNOMED CT to ICD-10-CM to facilitate adoption of ICD-10-CM.

Science.gov (United States)

Cartagena, F Phil; Schaeffer, Molly; Rifai, Dorothy; Doroshenko, Victoria; Goldberg, Howard S

2015-05-01

Develop and test web services to retrieve and identify the most precise ICD-10-CM code(s) for a given clinical encounter. Facilitate creation of user interfaces that 1) provide an initial shortlist of candidate codes, ideally visible on a single screen; and 2) enable code refinement. To satisfy our high-level use cases, the analysis and design process involved reviewing available maps and crosswalks, designing the rule adjudication framework, determining necessary metadata, retrieving related codes, and iteratively improving the code refinement algorithm. The Partners ICD-10-CM Search and Mapping Services (PI-10 Services) are SOAP web services written using Microsoft's.NET 4.0 Framework, Windows Communications Framework, and SQL Server 2012. The services cover 96% of the Partners problem list subset of SNOMED CT codes that map to ICD-10-CM codes and can return up to 76% of the 69,823 billable ICD-10-CM codes prior to creation of custom mapping rules. We consider ways to increase 1) the coverage ratio of the Partners problem list subset of SNOMED CT codes and 2) the upper bound of returnable ICD-10-CM codes by creating custom mapping rules. Future work will investigate the utility of the transitive closure of SNOMED CT codes and other methods to assist in custom rule creation and, ultimately, to provide more complete coverage of ICD-10-CM codes. ICD-10-CM will be easier for clinicians to manage if applications display short lists of candidate codes from which clinicians can subsequently select a code for further refinement. The PI-10 Services support ICD-10 migration by implementing this paradigm and enabling users to consistently and accurately find the best ICD-10-CM code(s) without translation from ICD-9-CM. © The Author 2015. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Gestational weight gain.

Science.gov (United States)

Kominiarek, Michelle A; Peaceman, Alan M

2017-12-01

Prenatal care providers are advised to evaluate maternal weight at each regularly scheduled prenatal visit, monitor progress toward meeting weight gain goals, and provide individualized counseling if significant deviations from a woman's goals occur. Today, nearly 50% of women exceed their weight gain goals with overweight and obese women having the highest prevalence of excessive weight gain. Risks of inadequate weight gain include low birthweight and failure to initiate breast-feeding whereas the risks of excessive weight gain include cesarean deliveries and postpartum weight retention for the mother and large-for-gestational-age infants, macrosomia, and childhood overweight or obesity for the offspring. Prenatal care providers have many resources and tools to incorporate weight and other health behavior counseling into routine prenatal practices. Because many women are motivated to improve health behaviors, pregnancy is often considered the optimal time to intervene for issues related to eating habits and physical activity to prevent excessive weight gain. Gestational weight gain is a potentially modifiable risk factor for a number of adverse maternal and neonatal outcomes and meta-analyses of randomized controlled trials report that diet or exercise interventions during pregnancy can help reduce excessive weight gain. However, health behavior interventions for gestational weight gain have not significantly improved other maternal and neonatal outcomes and have limited effectiveness in overweight and obese women. Copyright © 2017 Elsevier Inc. All rights reserved.

Spatial and temporal length distribution of Zungaro zungaro caught in the Orinoco River Basin of Colombia

Directory of Open Access Journals (Sweden)

Hernando Ramírez-Gil

2015-12-01

Full Text Available Objetive. To determine the effect of fishing on capture size of both male and female Zungaro zungaro catfish, historical records of size and spatial distribution of the species were analyzed from the Orinoco Basin in Colombian. Materials and methods. Information was collected by sampling fishing port landings in the region between 1979 and 2011. Each specimen was measured, weighed and sexed. With 5411 records, the average size at capture were compared in time and among the different ports. Size at 50% maturity was estimated by quinquennium. Results. The average commercial capture sizes of Z. zungaro ranged from 35 to 161 cm standard length, with differences between males and females. From 1979 to 2011, in Puerto Lopez, the size at sexual maturity decreased from 123.8 to 83.4 cm in females and from 93.3 to 61 in males. In the annual cycle the greater average capture size in females was from April to July and for males from May to June. Average annual length is higher in the higher parts of the Meta and Guaviare river drainages. In the last quinquennium the size at 50% maturity had fallen 10 cm in females and 5 cm in males and it is higher than the average capture size. Conclusions. Populations of Z. zungaro in the Colombian Orinoco River Basin have been affected by overfishing and selective fishing of females.

Effects of prescription depth, cylinder size, treatment length, tip space, and curved end on doses in high-dose-rate vaginal brachytherapy

International Nuclear Information System (INIS)

Li Shidong; Aref, Ibrahim; Walker, Eleanor; Movsas, Benjamin

2007-01-01

Purpose: To determine the effects of the prescription depth, cylinder size, treatment length, tip space, and curved end on high-dose-rate vaginal brachytherapy (HDR-VBT) of endometrial cancer. Methods and Materials: Treatment plans were prescribed and optimized based on points at the cylinder surface or at 0.5-cm depth. Cylinder sizes ranging from 2 to 4 cm in diameter, and treatment lengths ranging from 3 to 8 cm were used. Dose points in various depths were precisely defined along the cylinder dome. The given dose and dose uniformity to a depth of interest were measured by the mean dose (MD) and standard deviation (SD), respectively, among the dose points belonging to the depth. Dose fall-off beyond the 0.5 cm treatment depth was determined by the ratio of MD at 0.75-cm depth to MD at 0.5-cm depth. Results: Dose distribution varies significantly with different prescriptions. The surface prescription provides more uniform doses at all depths in the target volume, whereas the 0.5-cm depth prescription creates larger dose variations at the cylinder surface. Dosimetric uncertainty increases significantly (>30%) with shorter tip space. Extreme hot (>150%) and cold spots (<60%) occur if no optimization points were placed at the curved end. Conclusions: Instead of prescribing to a depth of 0.5 cm, increasing the dose per fraction and prescribing to the surface with the exact surface points around the cylinder dome appears to be the optimal approach

Ultralong Radiative States in Hybrid Perovskite Crystals: Compositions for Submillimeter Diffusion Lengths

KAUST Repository

Alarousu, Erkki

2017-08-29

Organic-inorganic hybrid perovskite materials have recently evolved into the leading candidate solution-processed semiconductor for solar cells due to their combination of desirable optical and charge transport properties. Chief among these properties is the long carrier diffusion length, which is essential to optimizing the device architecture and performance. Herein, we used time-resolved photoluminescence (at low excitation fluence, 10.59 μJ·cm upon two-photon excitation), which is the most accurate and direct approach to measure the radiative charge carrier lifetime and diffusion lengths. Lifetimes of about 72 and 4.3 μs for FAPbBr and FAPbI perovskite single crystals have been recorded, presenting the longest radiative carrier lifetimes reported to date for perovskite materials. Subsequently, carrier diffusion lengths of 107.2 and 19.7 μm are obtained. In addition, we demonstrate the key role of the organic cation units in modulating the carrier lifetime and its diffusion lengths, in which the defect formation energies for FA cations are much higher than those with the MA ones.

Deformation of HyFlex CM instruments and their shape recovery following heat sterilization.

Science.gov (United States)

Alfoqom Alazemi, M; Bryant, S T; Dummer, P M H

2015-06-01

To assess the deformation of HyFlex CM instruments (Coltene Whaledent) when used in two instrumentation sequences and to assess their shape recovery after heat sterilization. Simulated root canals with four different shapes were prepared with HyFlex CM instruments using a single-length technique (n = 40) or a crown down technique (n = 40). Pre-preparation, post-preparation and post-sterilization standardized images of each instrument were recorded. Assessment of instrument deformation and their subsequent shape recovery was carried out visually and by comparing the digitised images. Data analysis was carried out using chi-square tests. None of the 400 instruments fractured. Visual assessment of instruments post-preparation revealed that 30.5% had unwound and 0.5% had reverse winding. Following sterilization 8.5% remained unwound and 0.5% remained with reverse winding. When assessing instrument shape using digital images, 35.25% were unwound post-preparation, which reduced to 11% post-sterilization. Nine size 25, 0.08 instruments deformed, but none fully regained their original shape after sterilization; however, other sizes of deformed instruments did regain their shape (P recovery. © 2014 International Endodontic Journal. Published by John Wiley & Sons Ltd.

Gain claming in single-pass and double-pass L-band erbium-doped fiber amplifiers

International Nuclear Information System (INIS)

Harun, S.W.; Ahmad, H.

2004-01-01

Gain clamping is demonstrated in single-pass and double-pass long wavelength band erbium-doped fiber amplifiers. A C/L-band wavelength division multiplexing coupler is used in single-pass system to generate a laser at 1566 nm. The gain for the amplifier is clamped at 15.5 dB with gain variation of less than 0.2 dB from input signal power of -40 to -14 dBm with almost negligible noise figure penalty. However, the flatness of gain spectrum is slightly degraded due to the un-optimisation of erbium-doped fiber length. The advantage of this configuration is that the oscillating light does not appear at the output of the amplifier. A highly efficient gain-clamped long wavelength band erbium-doped fiber amplifiers with improved noise figure characteristic is demonstrated by simply adding a broadband conventional band fiber Bragg grating in double pass system. The combination of the fiber Bragg grating and optical circulator has created laser in the cavity for gain clamping. By adjusting the power combination of pumps 1 and 2, the clamped gain level can be controlled. The amplifier gain is clamped at 28.1 dB from -40 to -25 dBm with gain variation of less than 0.5 dB by setting the pumps 1 and 2 at 59.5 and 50.6 mW, respectively. The gain is also flat from 1574 nm to 1604 nm with gain variation of less than 3 dB. The corresponding noise figure varies from 5.6 to 7.6 dB, which is 0.8 to 2.6 dB reduced compared to those of unclamped amplifier (Authors)

Morphometric study of uninvolved rectal mucosa 10 cm and 20 cm away from the malignant tumor.

Science.gov (United States)

Despotović, Sanja Z; Milićević, Novica M; Milosević, Dragoslav P; Despotović, Nebojsa; Erceg, Predrag; Bojić, Bozidar; Bojić, Danijela; Svorcan, Petar; Mihajlović, Gordana; Dorđević, Jelena; Lalić, Ivana M; Milićević, Zivana

2014-02-01

Recently, many details of the interplay between tumor cells and tumor-associated stromal elements leading to the progression of malignant disease were elucidated. In contrast, little is known about the role of uninvolved stromal tissue in the remote surrounding of the malignant tumor. Therefore, we performed a computer-aided morphometric study of rectal mucosa in samples taken 10 cm and 20 cm away from the malignant tumor during endoscopic examination of 23 patients older than 60 years. The samples of rectal mucosa from 10 healthy persons of corresponding age subjected to diagnostic rectoscopy during active screening for asymptomatic cancer were used as control. All structural elements of the rectal mucosa were studied and the number of nucleated cells in the lamina propria per 0.1 mm² of tissue was assessed. Our study revealed a reduced number of cells in the lamina propria of the rectal mucosa 10 cm and 20 cm away from the tumor lesion in both male and female patients. The decreased mucosal height and increased crypt number were registered in female patients 10 cm away from the tumor. The connective tissue of lamina propria showed a disorderly organization: the collagen fibers were frail, loosely arranged and signs of tissue edema were present. Small blood vessels and capillaries were much more frequently seen than in healthy tissue. Our results demonstrate the complex interactions between the cancer and remote mucosal tissue of the affected organ.

Operational gain : measuring the capture of genetic gain ...

African Journals Online (AJOL)

The concept of operational gain is more than the weighted average of the genetic quality of planted hectares, and encompasses tree breeding efficiencies, propagation efficiencies, matching of species and genotype to site, plant use efficiency and early measures of stand density and growth. To test the operational gain ...

Steady-state pulses and superradiance in short-wavelength, swept-gain amplifiers

International Nuclear Information System (INIS)

Bonifacio, R.; Hopf, F.A.; Meystre, P.; Scully, M.O.

1975-01-01

The steady-state behavior of amplifiers in which the excitation is swept at the speed of light is discussed in the semiclassical approximation. In the present work the case where the decay time of the population is comparable to that of the polarization is examined. Pulse propagation is shown to obey a generalized sine-Gordon equation which contains the effects of atomic relaxations. The analytical expression of the steady-state pulses (SSP) gives two threshold conditions. In the region of limited gain the SSP is a broad pulse with small area which can be obtained by small signal theory. In the second region of high gain the SSP is the superradiant π pulse. Its pulse power is not limited as in usual superradiant theory because, as is shown, for a swept excitation the cooperation-length limit does not exist

High resolution spectroscopy of the OsO4 stretching fundamental at 961 cm-1

International Nuclear Information System (INIS)

McDowell, R.S.; Radziemski, L.J.; Flicker, H.; Galbraith, H.W.; Kennedy, R.C.; Nereson, N.G.; Krohn, B.J.; Aldridge, J.P.; King, J.D.; Fox, K.

1978-01-01

The ν 3 bands of 187 Os 16 O 4 , 189 Os 16 O 4 , and 192 Os 16 O 4 have been recorded using both a Michelson interferometer (resolution 0.06 cm -1 ) and a tunable semiconductor diode laser (resolution limited by the Doppler width, approx.0.0007 cm -1 ). The rotational fine structure differs from that of most other spherical-top molecules, for only rotational levels of A symmetry exist. A total of 112 individual vibration--rotation lines in the P and R branches of the three isotopic species were calibrated against stimulated emission lines from a high-voltage CO 2 gain cell, and were used to determine three scalar and two tensor spectroscopic constants for each species; an additional scalar constant was obtained from an analysis of the Q branch of 192 OsO 4 . The strength of P (11) A 2 /sup ts0/ was measured for 192 OsO 4 and yields a vibrational transition moment for ν 3 of 0.17 +- 0.02 D. Transitions of all isotopic species that are expected to fall near CO 2 laser lines in the region 949--972 cm -1 are tabulated as an aid in the interpreation of saturation spectroscopy experiments. The general quadratic symmetry and valence force constants of OsO 4 were redetermined, using the isotope shifts in ν 3 as the additional constraints for the F 2 symmetry block

Performance of p-type micro-strip detectors after irradiation to $7.5x10^{15} p/cm^{2}$

CERN Document Server

Allport, Philip P; Lozano-Fantoba, Manuel; Sutcliffe, Peter; Velthuis, J J; Vossebeld, Joost Herman

2004-01-01

Exploiting the advantages of reading out segmented silicon from the n-side, we have produced test detectors with LHC pitch but 1 cm long strips which even after proton irradiation at the CERN PS to 7.5*10 /sup 15/ cm/sup -2/ show signal to noise greater than 8:1 using LHC speed electronics. This dose exceeds by a factor of 2 that required for a replacement of the ATLAS semiconductor tracker to cope with an upgrade of the LHC to a Super-LHC with 10 times greater luminosity. These detectors were processed on p-type starting material of resistivity ~ 2 k Omega cm and, unlike n-in-n designs, only required single-sided processing. Such technology should therefore provide a relatively inexpensive route to replacing the central tracking at both ATLAS and CMS for Super-LHC. The shorter strip length is required to limit the noise. Even at these extreme doses 30% of the non-irradiated signal is seen. This 7000e/sup -/ signal (in 280 mu m thick sensors) is very competitive with the post irradiation performance of other,...

Gated cardiac blood pool studies in atrial fibrillation: Role of cycle length windowing

Energy Technology Data Exchange (ETDEWEB)

Wallis, J W; Juni, J E; Wu, L [Michigan Univ., Ann Arbor (USA). Div. of Nuclear Medicine

1991-01-01

Cycle length windowing is gaining increasing acceptance in gated blood pool imaging of patients with atrial fibrillation (AF). The goals of this study were: to assess differences of ejection fraction (EF) in AF with and without windowing and to determine how EF varied with cycle length in patients with AF. Twenty patients with AF were prospectively studied by gated blood pool imaging, with simultaneous collection in each patient of 5-7 studies with cycle length windows spanning the cycle length histogram. Each window accepted beats of only a narrow range of cycle lengths. EF was determined for each of the narrow cycle length windows as well as for the entire gated blood pool study without cycle length windowing. For every patient an average of the windowed EFs was compared with the non-windowed EF. EF values were similar (mean windowed: 46.6; non-windowed: 45.5; P=0.16), and there was a good correlation between the two techniques (r=0.97). The data were then examined for a relationship of EF with cycle length. The difference from average windowed EF ({Delta}EF) was calculated for each window and plotted vs. the cycle length of the center of each window. No predictable linear or nonlinear relationship of {Delta}EF with window position was observed. Lack of predictable variation of EF with cycle length is likely due to lack of a predictable amount of ventricular filling for a given cycle length, as the amount of diastolic filling in AF depends on the random cycle length of the preceding beat. In summary, windowing in AF does not provide a clinically significant difference in EF determination. If cycle length windowing is used, the exact location of the window is not critical. (orig.).

Precision modelling of M dwarf stars: the magnetic components of CM Draconis

Science.gov (United States)

MacDonald, J.; Mullan, D. J.

2012-04-01

The eclipsing binary CM Draconis (CM Dra) contains two nearly identical red dwarfs of spectral class dM4.5. The masses and radii of the two components have been reported with unprecedentedly small statistical errors: for M, these errors are 1 part in 260, while for R, the errors reported by Morales et al. are 1 part in 130. When compared with standard stellar models with appropriate mass and age (≈4 Gyr), the empirical results indicate that both components are discrepant from the models in the following sense: the observed stars are larger in R ('bloated'), by several standard deviations, than the models predict. The observed luminosities are also lower than the models predict. Here, we attempt at first to model the two components of CM Dra in the context of standard (non-magnetic) stellar models using a systematic array of different assumptions about helium abundances (Y), heavy element abundances (Z), opacities and mixing length parameter (α). We find no 4-Gyr-old models with plausible values of these four parameters that fit the observed L and R within the reported statistical error bars. However, CM Dra is known to contain magnetic fields, as evidenced by the occurrence of star-spots and flares. Here we ask: can inclusion of magnetic effects into stellar evolution models lead to fits of L and R within the error bars? Morales et al. have reported that the presence of polar spots results in a systematic overestimate of R by a few per cent when eclipses are interpreted with a standard code. In a star where spots cover a fraction f of the surface area, we find that the revised R and L for CM Dra A can be fitted within the error bars by varying the parameter α. The latter is often assumed to be reduced by the presence of magnetic fields, although the reduction in α as a function of B is difficult to quantify. An alternative magnetic effect, namely inhibition of the onset of convection, can be readily quantified in terms of a magnetic parameter δ≈B2/4�

Effects of Compost Type and Rootstock Length on Fruit and Vegetable Seedlings Growth in the Nursery

Directory of Open Access Journals (Sweden)

Dody Priadi

2016-11-01

Full Text Available The study was conducted to develop local fruit plants and to improve vegetable production at the Plant Germplasm Garden of RC for Biotechnology-LIPI. Carambola (Averrhoa carambola, durian (Durio zibethinus and guava (Psidium guajava were propagated vegetatively (grafting and budding and were grown on the media containing grass compost (K-1, spent compost of paddy straw mushroom (K-2 or oyster mushroom (K-3 in combination with rootstock length of 45-55 cm (TB-1, 65-75 cm (TB-2 and 75-90 cm (TB-3. Tomato (Lycopersicum esculentum and kangkung (Ipomoea reptans were grown on the same media in the screen house. The highest survival rate of grafted durian (71.56% was obtained from TB-3 grown on K-1 by budding technique. Meanwhile, the highest survival rate of carambola (68.89% was obtained from TB-1 by grafting technique. The budding technique was not appropriate for guava (0 % of survival. Application of K-3 of 3 kgs on tomato plants resulted in the highest fresh weight, length, and diameter of the fruit, and the highest of plant height, total leaves, and biomass of kangkung. The study is expected to be applied to improve fruit plant growth and survival rate as well as a high production of organic vegetable.How to CitePriadi, D., & Mulyaningsih, E. S. (2016. Effects of Compost Type and Rootstock Length on Fruit and Vegetable Seedlings Growth  in the Nursery. Biosaintifika: Journal of Biology & Biology Education, 8(3, 301-307. 

Comparison of fibroblast cell regeneration in three different concentrations of Wharton’s Jelly mesenchymal stem cells conditioned medium (WJMSCs-CM)

Science.gov (United States)

Untoro, E. G.; Asrianti, D.; Usman, M.; Meidyawati, R.; Margono, A.

2017-08-01

Wharton’s Jelly-derived mesenchymal stem cells (WJMSCs) have gained interest as an alternative source of stem cells for regenerative medicine. Although many studies have characterized Wharton’s Jelly biologically, the effects of different concentrations in a cultured medium have not yet been compared. Damaged fibroblasts, the primary components of irreversible dental pulpitis, irreversibly impair the ability to regenerate and lead to the disruption of extracellular matrix. This study was performed to evaluate the potency of three WJMSCs-CM concentrations in improving serum-starved fibroblasts. Fibroblasts were cultivated in five passages, and divided into four groups. The first group (the control group) consisted of fibroblast cells that had been treated using starvation methods. The other groups (the treatment groups) were treated with various concentration of WJMSCs-CM (50%, 25% and 12.5%). Proliferative ability was evaluated using a cell count method and analyzed with a one-way ANOVA. Cultivation of serum-starved fibroblasts produced significantly higher cell counts in 12.5% WJMSCs-CM compared to the 50% group. It can be concluded that 12.5% WJMSCs-CM is the most efficient concentration for fibroblast proliferation.

Vermiform appendix: positions and length – a study of 377 cases and literature review

Directory of Open Access Journals (Sweden)

Sandro Cilindro de Souza

2015-10-01

Full Text Available Objective: Evaluation of the frequency of the relative positions and length of vermiform appendix in a group of corpses examined by the authors. Method: Dissection of 377 adult cadavers autopsied. Results and conclusions: Retrocecal: 43.5%; subcecal: 24.4% post-ileal: 14.3%, pelvic: 9.3%; paracecal: 5.8%; and pre-ileal appendices: 2.4%, other positions: 0.27%, mean length: 11.4 cm. Resumo: Objetivo: Avaliação da frequência das posições relativas e do comprimento do apêndice vermiforme em um grupo de cadáveres examinados pelos autores. Método: Dissecção de 377 cadáveres adultos necropsiados. Resultados e conclusões: Apêndices retrocecais: 43,5%, subcecais: 24,4%, pós-ileais: 14,3%, pélvico: 9,3%, paracecais: 5,8%, pré-ileais 2,4%, outras posições: 0,27%. Comprimento médio: 11,4 cm. Keywords: Vermiform appendix, Cecum, Anatomical variation, Appendicitis, Palavras-chave: Apêndice vermiforme, Ceco, Variação anatômica, Apendicite

Scalability of pre-packed preparative chromatography columns with different diameters and lengths taking into account extra column effects.

Science.gov (United States)

Schweiger, Susanne; Jungbauer, Alois

2018-02-16

Small pre-packed columns are commonly used to estimate the optimum run parameters for pilot and production scale. The question arises if the experiments obtained with these columns are scalable, because there are substantial changes in extra column volume when going from a very small scale to a benchtop column. In this study we demonstrate the scalability of pre-packed disposable and non-disposable columns of volumes in the range of 0.2-20 ml packed with various media using superficial velocities in the range of 30-500 cm/h. We found that the relative contribution of extra column band broadening to total band broadening was not only high for columns with small diameters, but also for columns with a larger volume due to their wider diameter. The extra column band broadening can be more than 50% for columns with volumes larger than 10 ml. An increase in column diameter leads to high additional extra column band broadening in the filter, frits, and adapters of the columns. We found a linear relationship between intra column band broadening and column length, which increased stepwise with increases in column diameter. This effect was also corroborated by CFD simulation. The intra column band broadening was the same for columns packed with different media. An empirical engineering equation and the data gained from the extra column effects allowed us to predict the intra, extra, and total column band broadening just from column length, diameter, and flow rate. Copyright © 2018 The Author(s). Published by Elsevier B.V. All rights reserved.

Conformal Organohalide Perovskites Enable Lasing on Spherical Resonators

KAUST Repository

Sutherland, Brandon R.

2014-10-28

© 2014 American Chemical Society. Conformal integration of semiconductor gain media is broadly important in on-chip optical communication technology. Here we deploy atomic layer deposition to create conformally deposited organohalide perovskites-an attractive semiconducting gain medium-with the goal of achieving coherent light emission on spherical optical cavities. We demonstrate the high quality of perovskite gain media fabricated with this method, achieving optical gain in the nanosecond pulse regime with a threshold for amplified spontaneous emission of 65 ± 8 μJ cm-2. Through variable stripe length measurements, we report a net modal gain of 125 ± 22 cm-1 and a gain bandwidth of 50 ± 14 meV. Leveraging the high quality of the gain medium, we conformally coat silica microspheres with perovskite to form whispering gallery mode optical cavities and achieve lasing.

Depressed height gain of children associated with intrauterine exposure to polycyclic aromatic hydrocarbons (PAH) and heavy metals: the cohort prospective study.

Science.gov (United States)

Jedrychowski, Wiesław A; Perera, Frederica P; Majewska, Renata; Mrozek-Budzyn, Dorota; Mroz, Elżbieta; Roen, Emily L; Sowa, Agata; Jacek, Ryszard

2015-01-01

Fetal exposure to environmental toxicants may program the development of children and have long-lasting health impacts. The study tested the hypothesis that depressed height gain in childhood is associated with prenatal exposure to airborne polycyclic aromatic hydrocarbons (PAH) and heavy metals (lead and mercury). The study sample comprised 379 children born to non-smoking mothers among whom a total of 2011 height measurements were carried out over the 9-year follow-up period. Prenatal airborne PAH exposure was assessed by personal air monitoring of the mother in the second trimester of pregnancy and heavy metals were measured in cord blood. At the age of 3 residential air monitoring was done to evaluate the level of airborne PAH, and at the age 5 the levels of heavy metals were measured in capillary blood. The effect estimates of prenatal PAH exposure on height growth over the follow-up were adjusted in the General Estimated Equation (GEE) models for a wide set of relevant covariates. Prenatal exposure to airborne PAH showed a significant negative association with height growth, which was significantly decreased by 1.1cm at PAH level above 34.7 ng/m(3) (coeff.=-1.07, p=0.040). While prenatal lead exposure was not significantly associated with height restriction, the effect of mercury was inversely related to cord blood mercury concentration above 1.2 μg/L (coeff.=-1.21, p=0.020), The observed negative impact of prenatal PAH exposure on height gain in childhood was mainly mediated by shorter birth length related to maternal PAH exposure during pregnancy. The height gain deficit associated with prenatal mercury exposure was not seen at birth, but the height growth was significantly slower at later age. Copyright © 2014 Elsevier Inc. All rights reserved.

Waterborne polyurethane single-ion electrolyte from aliphatic diisocyanate and various molecular length of polyethylene glycol

Directory of Open Access Journals (Sweden)

2007-03-01

Full Text Available The waterborne polyurethane (WPU dispersions from the reaction of cycloaliphatic diisocyanates [4,4’-methylenebis(cyclohexyl isocyanate (H12MDI and isophorone diisocyanate (IPDI] and polyethylene glycol (PEG with various molecular lengths were synthesized using our modified acetone process. Differetial scanning calorimeter (DSC and Fourier transform infrared spectroscopy (FTIR were utilized to characterize WPU films for the behavior of their crystallinity and H-bonding of WPU films. The Tg value of WPU increases with increasing the molecular length of PEG, whereas the Tm of WPU decreases with increasing PEG length. Alternating current (AC impedance experiments were performed to determine the ionic conductivities of WPU films. The WPU gel electrolytes exhibits an ionic conductivity as high as ~ 10-5 S/cm at room temperature.

2-cm versus 4-cm surgical excision margins for primary cutaneous melanoma thicker than 2 mm: a randomised, multicentre trial

DEFF Research Database (Denmark)

Gillgren, Peter; Drzewiecki, Krzysztof T; Niin, Marianne

2011-01-01

Optimum surgical resection margins for patients with clinical stage IIA-C cutaneous melanoma thicker than 2 mm are controversial. The aim of the study was to test whether survival was different for a wide local excision margin of 2 cm compared with a 4-cm excision margin.......Optimum surgical resection margins for patients with clinical stage IIA-C cutaneous melanoma thicker than 2 mm are controversial. The aim of the study was to test whether survival was different for a wide local excision margin of 2 cm compared with a 4-cm excision margin....

MOS current gain cells with electronically variable gain and constant bandwidth

NARCIS (Netherlands)

Klumperink, Eric A.M.; Seevinck, Evert

1989-01-01

Two MOS current gain cells are proposed that provide linear amplification of currents supplied by several linear MOS V-I converters. The gain is electronically variable by a voltage or a current and can be made insensitive to temperature and IC processing. The gain cells have a constant

Comprimento da estaca no desenvolvimento de mudas de alecrim-pimenta Effect of cutting length on the development of pepper-rosmarin seedlings

Directory of Open Access Journals (Sweden)

Wellington Geraldo Oliveira Carvalho Júnior

2009-10-01

Full Text Available O objetivo deste trabalho foi avaliar a influência do comprimento de estacas caulinares no desenvolvimento de mudas de alecrim-pimenta (Lippia sidoides Cham.. As estacas foram coletadas de plantas matrizes do Horto Medicinal do Instituto de Ciências Agrárias da Universidade Federal de Minas Gerais, em Montes Claros, Minas Gerais. O experimento foi conduzido em casa de vegetação com nebulização intermitente. Utilizou-se o delineamento inteiramente casualizado, com quatro tratamentos e cinco repetições. Os tratamentos foram definidos pelos intervalos de comprimento das estacas (5 a 8cm, 8,1 a 11cm, 11,1 a 14cm e 14,1 a 17cm. Foram avaliados o número de raízes principais, o comprimento da maior raiz (cm, o número de brotações, a porcentagem de enraizamento, a avaliação visual do enraizamento e a fitomassa seca das brotações e das raízes (g. Os resultados indicam que o comprimento das estacas afeta o desenvolvimento de mudas de alecrim-pimenta, especialmente a fitomassa seca das brotações e das raízes. As estacas com 14,1 a 17cm apresentaram a maior porcentagem de enraizamento e as maiores médias para as outras variáveis analisadas, sendo, portanto, mais recomendadas para a propagação vegetativa de alecrim-pimenta.This research aimed to evaluate the effect of shoot cutting length on the development of pepper-rosmarin seedlings (Lippia sidoides Cham.. The cuttings were obtained from stock plants of the medicinal vegetable garden of Instituto de Ciências Agrárias/UFMG, Montes Claros, Minas Gerais, Brazil. The experiment was conducted in greenhouse conditions with intermittent mist. The experimental design was totally randomized with four treatments consisted of different size intervals (5 to 8cm, 8.1 to 11cm, 11.1 to 14cm and 14.1 to 17cm, with five replications each. The amount of shooting and root, the shooting and root dry weight (g, the the longest root length (cm, the visual rooting evaluation and the rooting

Effect of ultrasonic stimulation on particle transport and fate over different lengths of porous media

Science.gov (United States)

Chen, Xingxin; Wu, Zhonghan; Cai, Qipeng; Cao, Wei

2018-04-01

It is well established that seismic waves traveling through porous media stimulate fluid flow and accelerate particle transport. However, the mechanism remains poorly understood. To quantify the coupling effect of hydrodynamic force, transportation distance, and ultrasonic stimulation on particle transport and fate in porous media, laboratory experiments were conducted using custom-built ultrasonic-controlled soil column equipment. Three column lengths (23 cm, 33 cm, and 43 cm) were selected to examine the influence of transportation distance. Transport experiments were performed with 0 W, 600 W, 1000 W, 1400 W, and 1800 W of applied ultrasound, and flow rates of 0.065 cm/s, 0.130 cm/s, and 0.195 cm/s, to establish the roles of ultrasonic stimulation and hydrodynamic force. The laboratory results suggest that whilst ultrasonic stimulation does inhibit suspended-particle deposition and accelerate deposited-particle release, both hydrodynamic force and transportation distance are the principal controlling factors. The median particle diameter for the peak concentration was approximately 50% of that retained in the soil column. Simulated particle-breakthrough curves using extended traditional filtration theory effectively described the experimental curves, particularly the curves that exhibited a higher tailing concentration.

Not all streaks are the same: Individual differences in risk preferences during runs of gains and losses

Directory of Open Access Journals (Sweden)

Christopher T. Ball

2012-07-01

Full Text Available Runs of gains and losses are particularly salient to decision makers because of their perceived departure from randomness, as well as their immediate impact on the financial status of the decision makers. Past research has focused on decision making biases that relate to faulty conceptions of chance and luck, such as the gambler's fallacy and the hot hand effect. Participants in the current study bet on the outcomes of a long sequence of simulated coin tosses. Risk preferences were found to change as a function of run valence (i.e., losses vs. gains, run length, and financial status. Individuals were found to differ in the effect of all of these factors, in their responses to runs of gains and losses in sequential risky choice.

Neutronic feasibility studies using U-Mo dispersion fuel (9 Wt % Mo, 5.0 gU/cm3) for LEU conversion of the MARIA (Poland), IR-8 (Russia), and WWR-SM (Uzbekistan) research reactors

International Nuclear Information System (INIS)

Bretscher, M.M.; Deen, J.R.; Hanan, N.A.; Matos, E.

2000-01-01

U-Mo alloys dispersed in an Al matrix offer the potential for high-density uranium fuels needed for the LEU conversion of many research reactors. On-going fuel qualification tests by the US RERTR Program show good irradiation properties of U-Mo alloy dispersion fuel containing 7-10 weight percent molybdenum. For the neutronic studies in this paper the alloy was assumed to contain 9 wt % Mo (U-9Mo) with a uranium density in the fuel meat of 5.00 gU/cm 3 which corresponds to 32.5 volume % U-9Mo. Fuels containing U-9Mo have been used in Russian reactors since the 1950's. For the three research reactors analyzed here, LEU fuel element thicknesses are the same as those for the Russian-fabricated HEU reference fuel elements. Relative to the reference fuels containing 80-90% enriched uranium, LEU U-9Mo Al-dispersion fuel with 5.00 gU/cm 3 doubles the cycle length of the MARIA reactor and increases the IR-8 cycle length by about 11%. For the WWR-SM reactor, the cycle length, and thus the number of fuel assemblies used per year, is nearly unchanged. To match the cycle length of the 36% enriched fuel currently used in the WWR-SM reactor will require a uranium density in the LEU U-9Mo Al-dispersion fuel of about 5.4 gU/cm 3 . The 5.00 gU/cm 3 LEU fuel causes thermal neutron fluxes in water holes near the edge of the core to decrease by (6-8)% for all three reactors. (author)

Measurement of the diffusion length of thermal neutrons inside graphite

International Nuclear Information System (INIS)

Ertaud, A.; Beauge, R.; Fauquez, H.; De Laboulay, H.; Mercier, C.; Vautrey, L.

1948-11-01

The diffusion length of thermal neutrons inside a given industrial graphite is determined by measuring the neutron density inside a parallelepipedal piling up of graphite bricks (2.10 x 2.10 x 2.442 m). A 3.8 curies (Ra α → Be) source is placed inside the parallelepipedal block of graphite and thin manganese detectors are used. Corrections are added to the unweighted measurements to take into account the effects of the damping of supra-thermal neutrons in the measurement area. These corrections are experimentally deduced from the differential measurements made with a cadmium screen interposed between the source and the first plane of measurement. An error analysis completes the report. The diffusion length obtained is: L = 45.7 cm ± 0.3. The average density of the graphite used is 1.76 and the average apparent density of the piling up is 1.71. (J.S.)

Development of a Time Projection Chamber using CF4 gas for relativistic heavy ion experiments

International Nuclear Information System (INIS)

Isobe, T.; Hamagaki, H.; Ozawa, K.; Inuzuka, M.; Sakaguchi, T.; Matsumoto, T.; Kametani, S.; Kajihara, F.; Gunji, T.; Kurihara, N.; Oda, S.X.; Yamaguchi, Y.L.

2006-01-01

A prototype Time Projection Chamber (TPC) using pure CF 4 gas was developed for possible use in heavy ion experiments. Basic characteristics such as gain, drift velocity, longitudinal diffusion and attenuation length of produced electrons were measured with the TPC. At an electric field of 900V/cm, the drift velocity and longitudinal diffusion for 1cm drift were obtained as 10cm/μs and 60μm, respectively. The relatively large gain fluctuation is explained to be due to the electron attachment process in CF 4 . These characteristics are encouraging for the measurement of the charged particle trajectories under high multiplicity conditions at RHIC

Observation of an energy threshold for large ΔE collisional relaxation of highly vibrationally excited pyrazine (Evib=31 000-41 000 cm-1) by CO2

Science.gov (United States)

Elioff, Michael S.; Wall, Mark C.; Lemoff, Andrew S.; Mullin, Amy S.

1999-03-01

Energy dependent studies of the collisional relaxation of highly vibrationally excited pyrazine through collisions with CO2 were performed for initial pyrazine energies Evib=31 000-35 000 cm-1. These studies are presented along with earlier results for pyrazine with Evib=36 000-41 000 cm-1. High-resolution transient IR laser absorption of individual CO2 (0000) rotational states (J=56-80) was used to investigate the magnitude and partitioning of energy gain into CO2 rotation and translation, which comprises the high energy tail of the energy transfer distribution function. Highly vibrationally excited pyrazine was prepared by absorption of pulsed UV light at seven wavelengths in the range λ=281-324 nm, followed by radiationless decay to pyrazine's ground electronic state. Nascent CO2 (0000) rotational populations were measured for each UV excitation wavelength and distributions of nascent recoil velocities for individual rotational states of CO2 (0000) were obtained from Doppler-broadened transient linewidth measurements. Measurements of energy transfer rate constants at each UV wavelength yield energy-dependent probabilities for collisions involving large ΔE values. These results reveal that the magnitude of large ΔE collisional energy gain in CO2 (0000) is fairly insensitive to the amount of vibrational energy in pyrazine for Evib=31 000-35 000 cm-1. A comparison with earlier studies on pyrazine with Evib=36 000-41 000 cm-1 indicates that the V→RT energy transfer increases both in magnitude and probability for Evib>36 000 cm-1. Implications of incomplete intramolecular vibrational relaxation, electronic state coupling, and isomerization barriers are discussed in light of these results.

An experimental analysis of the waveguide modes in a high-gain free-electron laser amplifier

International Nuclear Information System (INIS)

Anderson, B.R.

1989-01-01

The presence, growth, and interaction of transverse waveguide modes in high-gain free-electron laser (FEL) amplifiers has been observed and studied. Using the Electron Laser Facility at Lawrence Livermore National Laboratory, a 3 MeV, 800 A electron beam generated by the Experimental Test Accelerator was injected into a planar wiggler. Power was then extracted and measured in the fundamental (TE 01 ) an higher-order modes (Te 21 and TM 21 ) under various sets of operating conditions. Horizontal focusing through the wiggler was provided by external quadrupole magnets. There was no axial guide field. The input microwave signal for amplification was generated by a 100 kW magnetron operating at 34.6 Ghz. Power measurements were taken for both flat and tapered wigglers, for two sizes of waveguide, and for both flat and tapered wigglers, for two sizes of waveguide, and for both fundamental and higher mode injection. Mode content was determined by sampling the radiated signal at specific points in the radiation patter. For the flat wiggler and with the large waveguide (2.9 cm x 9.8 cm) the power in the higher modes was comparable to power in the fundamental. both exhibited gains greater than 30 dB/m prior to saturation and both reached powers in excess of 80 MW. Choice of injection mode had little effect on the operation of the system. Operation with the smaller guide (WR-229) provided much better mode selectivity. The fundamental mode continued to show optimum gain in excess of 30 dB/m while the higher-mode gain was of order 20 dB/m. As expected, power output increased significantly with the tapered wigglers. The relative mode content depended on the specific taper used

Search for a particle with a long interaction length

International Nuclear Information System (INIS)

Barrowes, S.C.; Huggett, R.W.; Jones, W.V.; Levit, L.B.; Porter, L.G.

1975-01-01

A search has been carried out for a long-lived particle having an interaction length lambdasub(m) = 300 to 2,000 cm -2 in air. Such a particle, called the mandela, has been proposed by the Leeds group to explain an anomalous energy spectrum of particles observed near sea level with a shallow spectrometer. Data taken at mountain altitude with a deep spectrometer has been examined for compatibility with the existence of the mandela. Although the data tend to favor the mandela hypothesis the results are not conclusive and appear to be explainable by conventional means. (orig.) [de

Oxygen isotope systematics of chondrules in the Murchison CM2 chondrite and implications for the CO-CM relationship

Science.gov (United States)

Chaumard, Noël; Defouilloy, Céline; Kita, Noriko T.

2018-05-01

High-precision oxygen three-isotope measurements of olivine and pyroxene were performed on 29 chondrules in the Murchison CM2 chondrite by secondary ion mass spectrometry (SIMS). The oxygen isotope ratios of analyzed chondrules all plot very close to the primitive chondrule minerals (PCM) line. In each of 24 chondrules, the olivine and/or pyroxene grains analyzed show indistinguishable oxygen isotope ratios. Exceptions are minor occurrences of isotopically distinguished relict olivine grains, which were found in nine chondrules. The isotope homogeneity of these phenocrysts is consistent with a co-magmatic crystallization of olivine and pyroxene from the final chondrule melts and a significant oxygen isotope exchange between the ambient gas and the melts. Homogeneous type I chondrules with Mg#'s of 98.9-99.5 have host chondrule Δ17O values ranging from -6.0‰ to -4.1‰, with one exception (Δ17O: -1.2‰; Mg#: 99.6). Homogeneous chondrules with Mg#'s poor H2O ice (∼0.3-0.4× the CI dust; Δ17O > 0‰) and at dust enrichments of ∼300-2000×. Regarding the Mg# and oxygen isotope ratios, the chondrule populations sampled by CM and CO chondrites are similar and indistinguishable. The similarity of these 16O-rich components in CO and CM chondrites is also supported by the common Fe/Mn ratio of olivine in type II chondrules. Although they accreted similar high-temperature silicates, CO chondrites are anhydrous compared to CM chondrites, suggesting they derived from different parent bodies formed inside and outside the snow line, respectively. If chondrules in CO and CM chondrites formed at the same disk locations but the CM parent body accreted later than the CO parent body, the snow line might have crossed the common chondrule-forming region towards the Sun between the time of the CO and CM parent bodies accretion.

Dividing the Force Concept Inventory into two equivalent half-length tests

Directory of Open Access Journals (Sweden)

Jing Han

2015-05-01

Full Text Available The Force Concept Inventory (FCI is a 30-question multiple-choice assessment that has been a building block for much of the physics education research done today. In practice, there are often concerns regarding the length of the test and possible test-retest effects. Since many studies in the literature use the mean score of the FCI as the primary variable, it would be useful then to have different shorter tests that can produce FCI-equivalent scores while providing the benefits of being quicker to administer and overcoming the test-retest effects. In this study, we divide the 1995 version of the FCI into two half-length tests; each contains a different subset of the original FCI questions. The two new tests are shorter, still cover the same set of concepts, and produce mean scores equivalent to those of the FCI. Using a large quantitative data set collected at a large midwestern university, we statistically compare the assessment features of the two half-length tests and the full-length FCI. The results show that the mean error of equivalent scores between any two of the three tests is within 3%. Scores from all tests are well correlated. Based on the analysis, it appears that the two half-length tests can be a viable option for score based assessment that need to administer tests quickly or need to measure short-term gains where using identical pre- and post-test questions is a concern.

Optical gain and gain suppression of quantum-well lasers with valence band mixing

International Nuclear Information System (INIS)

Ahn, D.; Chuang, S.L.

1990-01-01

The effects of valence band mixing on the nonlinear gains of quantum-well lasers are studied theoretically. The authors' analysis is based on the multiband effective-mass theory and the density matrix formalism with intraband relaxation taken into account. The gain and the gain-suppression coefficient of a quantum-well laser are calculated from the complex optical susceptibility obtained by the density matrix formulation with the theoretical dipole moments obtained from the multiband effective-mass theory. The calculated gain spectrum shows that there are remarkable differences (both in peak amplitude and spectral shape) between our model with valence band mixing and the conventional parabolic band model. The shape of the gain spectrum calculated by the authors' model becomes more symmetric due to intraband relaxation together with nonparabolic energy dispersions and is closer to the experimental observations when compared with the conventional method using the parabolic band model and the multiband effective-mass calculation without intraband relaxation. Both give quite asymmetric gain spectra. Optical intensity in the GaAs active region is estimated by solving rate equations for the stationary states with nonlinear gain suppression. The authors calculate the mode gain for the resonant mode including the gain suppression, which results in spectral hole burning of the gain spectrum

Upper Limits on the 21 cm Epoch of Reionization Power Spectrum from One Night with LOFAR

Science.gov (United States)

Patil, A. H.; Yatawatta, S.; Koopmans, L. V. E.; de Bruyn, A. G.; Brentjens, M. A.; Zaroubi, S.; Asad, K. M. B.; Hatef, M.; Jelić, V.; Mevius, M.; Offringa, A. R.; Pandey, V. N.; Vedantham, H.; Abdalla, F. B.; Brouw, W. N.; Chapman, E.; Ciardi, B.; Gehlot, B. K.; Ghosh, A.; Harker, G.; Iliev, I. T.; Kakiichi, K.; Majumdar, S.; Mellema, G.; Silva, M. B.; Schaye, J.; Vrbanec, D.; Wijnholds, S. J.

2017-03-01

We present the first limits on the Epoch of Reionization 21 cm H I power spectra, in the redshift range z = 7.9-10.6, using the Low-Frequency Array (LOFAR) High-Band Antenna (HBA). In total, 13.0 hr of data were used from observations centered on the North Celestial Pole. After subtraction of the sky model and the noise bias, we detect a non-zero {{{Δ }}}{{I}}2={(56+/- 13{mK})}2 (1-σ) excess variance and a best 2-σ upper limit of {{{Δ }}}212< {(79.6{mK})}2 at k = 0.053 h cMpc-1 in the range z = 9.6-10.6. The excess variance decreases when optimizing the smoothness of the direction- and frequency-dependent gain calibration, and with increasing the completeness of the sky model. It is likely caused by (I) residual side-lobe noise on calibration baselines, (II) leverage due to nonlinear effects, (III) noise and ionosphere-induced gain errors, or a combination thereof. Further analyses of the excess variance will be discussed in forthcoming publications.

THE EFFECT OF FERMENTED OIL PALM FRONDS IN DIET ON BODY WEIGHT GAIN AND MEAT QUALITY OF GOAT

Directory of Open Access Journals (Sweden)

E. Musnandar

2011-06-01

Full Text Available The aims of study were to evaluate the use of fermented of oil palm fronds (FOPF on body weight gain and meat quality of goat. This experiment was arranged in Completely Randomized Design with 3 treatments i.e. R1 (grass 0%: FOPF 100%, R2 (grass 50%: FOPF 50% and R3 (grass 100%: FOPF 0% and 5 replications. The parameters of the study were feed intake, average daily gain (ADG, weight and percentage of carcass and meat quality. The results indicated that feed intake and meat quality of goat was not affected by treatment, but the average daily gain, carcass weight, and percentage of carcass, was affected by the differences of percentage of FOPF in the pellet complete feed. The best ration was in the R1 ration (grass 0%: FOPF 100% that significantly different (P<0.05 from the other rations. The feed intake tended to be higher in goat fed R1 (895.87 g/d compared to those in goat with the R2 (854.38 g/d and R3 (851.53 g/d. The average daily gain and carcass weight were higher in goat fed R1 ration compared to those in goat fed R2 and R3. Consequently, the carcass percentage in R1 was higher than those in R2 and R3. The carcass percentage was ranged from 38.41-41.38%. The Ribeye area was higher in goat fed R1 (9.73 cm2 than R2 (8.34 cm2 and R3 (7.76 cm2. In this study, the protein content of goat meat was ranged from 19.06 to 20.71%, lipid content was ranged from 0.703 to 1.106% and water content was range from 72.45% to 74.12%, in which were not different among the treatments. It can be concluded that the use of FOPF in a complete feed could improve performance and meat quality of goat.

A Restriction Fragment Length Polymorphism Map and Electrophoretic Karyotype of the Fungal Maize Pathogen Cochliobolus Heterostrophus

Science.gov (United States)

Tzeng, T. H.; Lyngholm, L. K.; Ford, C. F.; Bronson, C. R.

1992-01-01

A restriction fragment length polymorphism (RFLP) map has been constructed of the nuclear genome of the plant pathogenic ascomycete Cochliobolus heterostrophus. The segregation of 128 RFLP and 4 phenotypic markers was analyzed among 91 random progeny of a single cross; linkages were detected among 126 of the markers. The intact chromosomal DNAs of the parents and certain progeny were separated using pulsed field gel electrophoresis and hybridized with probes used to detect the RFLPs. In this way, 125 markers were assigned to specific chromosomes and linkages among 120 of the markers were confirmed. These linkages totalled 941 centimorgans (cM). Several RFLPs and a reciprocal translocation were identified tightly linked to Tox1, a locus controlling host-specific virulence. Other differences in chromosome arrangement between the parents were also detected. Fourteen gaps of at least 40 cM were identified between linkage groups on the same chromosomes; the total map length was therefore estimated to be, at a minimum, 1501 cM. Fifteen A chromosomes ranging from about 1.3 megabases (Mb) to about 3.7 Mb were identified; one of the strains also has an apparent B chromosome. This chromosome appears to be completely dispensable; in some progeny, all of 15 markers that mapped to this chromosome were absent. The total genome size was estimated to be roughly 35 Mb. Based on these estimates of map length and physical genome size, the average kb/cM ratio in this cross was calculated to be approximately 23. This low ratio of physical to map distance should make this RFLP map a useful tool for cloning genes. PMID:1346261

Minimizing Leg Length Discrepancy After Intramedullary Nailing of Comminuted Femoral Shaft Fractures: A Quality Improvement Initiative Using the Scout Computed Tomography Scanogram.

Science.gov (United States)

Gheraibeh, Petra; Vaidya, Rahul; Hudson, Ian; Meehan, Robert; Tonnos, Frederick; Sethi, Anil

2018-05-01

To prevent leg length discrepancy (LLD) after locked femoral nailing in patients with comminuted femoral shaft fractures. Prospective consecutive case series aimed at quality improvement. Level 1 Trauma Center PATIENTS:: Ninety-eight consecutive patients with a comminuted femoral shaft fracture underwent statically locked intramedullary nailing, with a focused attempt at minimizing LLD during surgery. A computed tomography scanogram of both legs was performed on postoperative day 1 to assess for residual LLD. Patients were offered the option to have LLD >1.5 cm corrected before discharge. LLD >1.5 cm. Twenty-one patients (21.4%) were found to have an LLD >1.5 cm. An LLD >1.5 cm occurred in 10/55 (18%) antegrade nail patients and 11/43 (26%) retrograde nail patients (P = 0.27). No difference was noted based on the mechanism of injury, surgeon training and OTA/AO type B versus C injury. Ninety of 98 patients left with 1.5 cm after locked intramedullary nailing for a comminuted femoral shaft fracture without being informed and the option of early correction. We recommend using a full-length computed tomography scanogram after IM nailing of comminuted femur fractures to prevent iatrogenic LLD. Therapeutic Level IV. See Instructions for Authors for a complete description of levels of evidence.

Peripartum Morbidity after Cesarean Delivery for Arrest of Dilation at 4 to 5 cm Compared with 6 to 10 cm.

Science.gov (United States)

Dahlke, Joshua D; Sperling, Jeffrey D; Has, Phinnara; Lovgren, Todd R; Connealy, Brendan D; Rouse, Dwight J

2018-04-24

 Given that recent consensus guidelines established to decrease cesarean delivery (CD) rates use 6 cm to define the onset of the active phase of labor, our objective was to evaluate maternal and neonatal outcomes after CD for the indication of arrest of dilation at 4 to 5 cm compared with ≥ 6 cm.  We performed a secondary analysis using data from the Maternal Fetal-Medicine Units Network Cesarean Registry. We included nulliparous women with term, singleton, vertex gestations who underwent primary CD for arrest of dilation. We compared those who reached a maximum cervical dilation of 4 to 5 cm with those of ≥6 cm. Our primary outcome was composite maternal morbidity that included chorioamnionitis, endometritis, transfusion, wound complication, operative injury, intensive care unit admission, or death.  Of the 73,257 women in the dataset, 5,681 met the inclusion criteria. After adjusting for confounders, there was no difference in composite maternal (adjusted odds ratio [aOR]: 1.19; 95% confidence interval [CI]: 0.94-1.52) or neonatal morbidity (aOR: 0.94; 95% CI: 0.79-1.10) between the groups.  In this historical cohort, maternal and neonatal outcomes after CD for arrest of dilation ≥ 6 cm were comparable to those performed at 4 to 5 cm and support recent labor management guidelines. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

Age, growth and length-weight relationship of the white skate, Rostroraja alba (Linnaeus, 1758 (Chondrichthyans: Rajidae, from the Gulf of Gabes (Tunisia, Central Mediterranean

Directory of Open Access Journals (Sweden)

Hasna Kadri

2014-06-01

Full Text Available Objective: To investigate the length distribution, sex ratio, length-weight relationship, age and growth of Rostroraja alba in the Gulf of Gabes. Methods: This study estimated age and growth of the white skate, Rostroraja alba by counting vertebral band pairs from 112 specimens taken by commercial fisheries during 2006-2009 from the Gulf of Gabes (Southern Tunisia, Central Mediterranean Sea. Results: This is the first and only known information in regards to the age and growth of this species in Tunisia. Vertebra diameter was strongly correlated with total length and age, which were expressed by linear or cubic regression equations. The oldest female in this study was 35 years and 160 cm, whereas the oldest male was 32 years and 150 cm. The von Bertalanffy growth parameters were TL∞=(202.26±3.40 cm, K=(0.040±0.038/year and t0=(1.84±0.01 10 -1 /year for females and TL∞=(198.60±3.61 cm, K=(0.060±0.076/year and t0=(1.28±0.04/year for males. Conclusions: This study would be an effective tool for fishery biologists, managers and conservationists to initiate management strategies and regulations for the sustainable conservation of the remaining stocks of this species in the Gulf of Gabes (Southern Tunisia ecosystem

Combined Treatment with Gonadotropin-releasing Hormone Analog and Anabolic Steroid Hormone Increased Pubertal Height Gain and Adult Height in Boys with Early Puberty for Height.

Science.gov (United States)

Tanaka, Toshiaki; Naiki, Yasuhiro; Horikawa, Reiko

2012-04-01

Twenty-one boys with a height of 135 cm or less at onset of puberty were treated with a combination of GnRH analog and anabolic steroid hormone, and their pubertal height gain and adult height were compared with those of untreated 29 boys who enter puberty below 135 cm. The mean age at the start of treatment with a GnRH analog, leuprorelin acetate depot (Leuplin(®)) was 12.3 yr, a mean of 1.3 yr after the onset of puberty, and GnRH analog was administered every 3 to 5 wk thereafter for a mean duration of 4.1 yr. The anabolic steroid hormone was started approximately 1 yr after initiation of treatment with the GnRH analog. The mean pubertal height gain from onset of puberty till adult height was significantly greater in the combination treatment group (33.9 cm) than in the untreated group (26.4 cm) (ppenis and pubic hair is promoted by the anabolic steroid hormone, no psychosocial problems arose because of delayed puberty. No clinically significant adverse events appeared. Combined treatment with GnRH analog and anabolic steroid hormone significantly increased height gain during puberty and adult height in boys who entered puberty with a short stature, since the period until epiphyseal closure was extended due to deceleration of the bone age maturation by administration of the GnRH analog and the growth rate at this time was maintained by the anabolic steroid hormone.

77 FR 8877 - ICD-9-CM Coordination and Maintenance (C&M) Committee Meeting

Science.gov (United States)

2012-02-15

...), Classifications and Public Health Data Standards Staff, announces the following meeting. Name: ICD-9-CM... proposed modifications to the International Classification of Diseases, Ninth-Revision, Clinical... Infusion of Glucarpidase ICD-10 Updates: ICD-10 MS-DRG Update ICD-10 HAC Translation List Impact of ICD-10...

Effect of Aspiration and Mean Gain on the Emergence of Cooperation in Unidirectional Pedestrian Flow

International Nuclear Information System (INIS)

Wang Zi-Yang; Zhao Hui; Ma Jian; Qin Yong; Jia Li-Min; Zhu Wei

2013-01-01

When more than one pedestrian want to move to the same site, conflicts appear and thus the involved pedestrians play a motion game. In order to describe the emergence of cooperation during the conflict resolving process, an evolutionary cellular automation model is established considering the effect of aspiration and mean gain. In each game, pedestrian may be gentle cooperator or aggressive defector. We propose a set of win-stay-lose-shrift (WSLS) like rules for updating pedestrian's strategy. These rules prescribe that if the mean gain of current strategy between some given steps is larger than aspiration the strategy keeps, otherwise the strategy changes. The simulation results show that a high level aspiration will lead to more cooperation. With the increment of the statistic length, pedestrians will be more rational in decision making. It is also found that when the aspiration level is small enough and the statistic length is large enough all the pedestrian will turn to defectors. We use the prisoner's dilemma model to explain it. At last we discuss the effect of aspiration on fundamental diagram. (interdisciplinary physics and related areas of science and technology)

Detecting primordial gravitational waves with circular polarization of the redshifted 21 cm line. II. Forecasts

Science.gov (United States)

Mishra, Abhilash; Hirata, Christopher M.

2018-05-01

In the first paper of this series, we showed that the CMB quadrupole at high redshifts results in a small circular polarization of the emitted 21 cm radiation. In this paper we forecast the sensitivity of future radio experiments to measure the CMB quadrupole during the era of first cosmic light (z ˜20 ). The tomographic measurement of 21 cm circular polarization allows us to construct a 3D remote quadrupole field. Measuring the B -mode component of this remote quadrupole field can be used to put bounds on the tensor-to-scalar ratio r . We make Fisher forecasts for a future Fast Fourier Transform Telescope (FFTT), consisting of an array of dipole antennas in a compact grid configuration, as a function of array size and observation time. We find that a FFTT with a side length of 100 km can achieve σ (r )˜4 ×10-3 after ten years of observation and with a sky coverage fsky˜0.7 . The forecasts are dependent on the evolution of the Lyman-α flux in the pre-reionization era, that remains observationally unconstrained. Finally, we calculate the typical order of magnitudes for circular polarization foregrounds and comment on their mitigation strategies. We conclude that detection of primordial gravitational waves with 21 cm observations is in principle possible, so long as the primordial magnetic field amplitude is small, but would require a very futuristic experiment with corresponding advances in calibration and foreground suppression techniques.

Dynamics of a gain-switched distributed feedback ridge waveguide laser in nanoseconds time scale under very high current injection conditions.

Science.gov (United States)

Klehr, A; Wenzel, H; Brox, O; Schwertfeger, S; Staske, R; Erbert, G

2013-02-11

We present detailed experimental investigations of the temporal, spectral and spatial behavior of a gain-switched distributed feedback (DFB) laser emitting at a wavelength of 1064 nm. Gain-switching is achieved by injecting nearly rectangular shaped current pulses having a length of 50 ns and a very high amplitude up to 2.5 A. The repetition frequency is 200 kHz. The laser has a ridge waveguide (RW) for lateral waveguiding with a ridge width of 3 µm and a cavity length of 1.5 mm. Time resolved investigations show, depending on the amplitude of the current pulses, that the optical power exhibits different types of oscillatory behavior during the pulses, accompanied by changes in the lateral near field intensity profiles and optical spectra. Three different types of instabilities can be distinguished: mode beating with frequencies between 25 GHz and 30 GHz, switching between different lateral intensity profiles with a frequency of 0.4 GHz and self-sustained oscillations with a frequency of 4 GHz. The investigations are of great relevance for the utilization of gain-switched DFB-RW lasers as seed lasers for fiber laser systems and in other applications, which require a high optical power.

Transvaginal cervical length and amniotic fluid index: can it predict delivery latency following preterm premature rupture of membranes?

Science.gov (United States)

Mehra, Suwan; Amon, Erol; Hopkins, Sarah; Gavard, Jeffrey A; Shyken, Jaye

2015-03-01

We sought to determine whether transvaginal cervical length (TVCL), amniotic fluid index (AFI), or a combination of both can predict delivery latency within 7 days in women presenting with preterm premature rupture of membranes (PPROM). This was a prospective observational study of TVCL measurements in 106 singleton pregnancies with PPROM between 23-33 weeks. Delivery latency was defined as the period (in days) from the initial TVCL after PPROM to delivery of the infant, with our primary outcome being delivery within 7 days of TVCL. The independent predictability of significant characteristics for delivery within 7 days was determined using multiple logistic regression. Sensitivity, specificity, and predictive values were used to examine whether the presence of a short TVCL, AFI, or a combination of both affected the risk of delivery within 7 days. Delivery within 7 days occurred in 51/106 (48%) of pregnancies. Median duration (interquartile range) from PPROM to delivery and TVCL to delivery was 8 days (4.0-16.0) and 8 days (3.0-15.0), respectively. Using multiple regression TVCL as a continuous variable (odds ratio, 0.65; 95% confidence interval, 0.44-0.97; P 7 days for TVCL >2 cm alone was 61%. This predictive value changed when analyzed in conjunction with an AFI ≤5 cm and >5 cm at 42% and 89%, respectively. A shorter TVCL and an AFI ≤5 cm independently predict delivery within 7 days in women presenting with PPROM. The combination of an AFI >5 cm and TVCL >2 cm greatly improved the potential to remain undelivered at 7 days following cervical length assessment. These findings may be helpful for counseling and optimizing maternal and neonatal care in women with PPROM. Copyright © 2015 Elsevier Inc. All rights reserved.

Assessing Leg length Discrepancy Using a Biplane Low Dose Imaging System. A Comparative Diagnostic Study

DEFF Research Database (Denmark)

Jensen, Janni; Mussmann, Bo Redder; Torfing, Trine

study was to evaluate the diagnostic accuracy of leg length (LL) measurements performed on low dose pre-view images acquired using a new bi-planar imaging system. The administered radiation dose from the pre-view image is approximately 20,17μGycm2 vs. 2670μGycm2 when acquiring the diagnostic image.......84) for the tibial measurements and the mean difference for total LLD was 0.01cm (p=0.92) and 0.03cm (p=0.73). All ICC calculations were >.99 indicating excellent inter- and intra-rater reliability. Conclusion. The results strongly imply that LL measurements performed on pre-view images acquired with a new bi...

Should I Gain Weight?

Science.gov (United States)

... Videos for Educators Search English Español Should I Gain Weight? KidsHealth / For Teens / Should I Gain Weight? ... something about it. Why Do People Want to Gain Weight? Some of the reasons people give for ...

Developmental gains in visuospatial memory predict gains in mathematics achievement.

Directory of Open Access Journals (Sweden)

Yaoran Li

Full Text Available Visuospatial competencies are related to performance in mathematical domains in adulthood, but are not consistently related to mathematics achievement in children. We confirmed the latter for first graders and demonstrated that children who show above average first-to-fifth grade gains in visuospatial memory have an advantage over other children in mathematics. The study involved the assessment of the mathematics and reading achievement of 177 children in kindergarten to fifth grade, inclusive, and their working memory capacity and processing speed in first and fifth grade. Intelligence was assessed in first grade and their second to fourth grade teachers reported on their in-class attentive behavior. Developmental gains in visuospatial memory span (d = 2.4 were larger than gains in the capacity of the central executive (d = 1.6 that in turn were larger than gains in phonological memory span (d = 1.1. First to fifth grade gains in visuospatial memory and in speed of numeral processing predicted end of fifth grade mathematics achievement, as did first grade central executive scores, intelligence, and in-class attentive behavior. The results suggest there are important individual differences in the rate of growth of visuospatial memory during childhood and that these differences become increasingly important for mathematics learning.

Developmental gains in visuospatial memory predict gains in mathematics achievement.

Science.gov (United States)

Li, Yaoran; Geary, David C

2013-01-01

Visuospatial competencies are related to performance in mathematical domains in adulthood, but are not consistently related to mathematics achievement in children. We confirmed the latter for first graders and demonstrated that children who show above average first-to-fifth grade gains in visuospatial memory have an advantage over other children in mathematics. The study involved the assessment of the mathematics and reading achievement of 177 children in kindergarten to fifth grade, inclusive, and their working memory capacity and processing speed in first and fifth grade. Intelligence was assessed in first grade and their second to fourth grade teachers reported on their in-class attentive behavior. Developmental gains in visuospatial memory span (d = 2.4) were larger than gains in the capacity of the central executive (d = 1.6) that in turn were larger than gains in phonological memory span (d = 1.1). First to fifth grade gains in visuospatial memory and in speed of numeral processing predicted end of fifth grade mathematics achievement, as did first grade central executive scores, intelligence, and in-class attentive behavior. The results suggest there are important individual differences in the rate of growth of visuospatial memory during childhood and that these differences become increasingly important for mathematics learning.

Developmental Gains in Visuospatial Memory Predict Gains in Mathematics Achievement

Science.gov (United States)

Li, Yaoran; Geary, David C.

2013-01-01

Visuospatial competencies are related to performance in mathematical domains in adulthood, but are not consistently related to mathematics achievement in children. We confirmed the latter for first graders and demonstrated that children who show above average first-to-fifth grade gains in visuospatial memory have an advantage over other children in mathematics. The study involved the assessment of the mathematics and reading achievement of 177 children in kindergarten to fifth grade, inclusive, and their working memory capacity and processing speed in first and fifth grade. Intelligence was assessed in first grade and their second to fourth grade teachers reported on their in-class attentive behavior. Developmental gains in visuospatial memory span (d = 2.4) were larger than gains in the capacity of the central executive (d = 1.6) that in turn were larger than gains in phonological memory span (d = 1.1). First to fifth grade gains in visuospatial memory and in speed of numeral processing predicted end of fifth grade mathematics achievement, as did first grade central executive scores, intelligence, and in-class attentive behavior. The results suggest there are important individual differences in the rate of growth of visuospatial memory during childhood and that these differences become increasingly important for mathematics learning. PMID:23936154

CM: Becoming a technology firm (teaching case)

NARCIS (Netherlands)

van Burg, J.C.; Reymen, I.M.M.J.; Dolmans, S.A.M.

2011-01-01

Founded in 2000 as a Short Message Service (SMS) marketing company for discos (clubs), CM evolved into a technology provider for SMS services. By 2008, CM was market leader in The Netherlands, a position won by offering high quality services at low prices. In 2010, the founders of the company were

The statistical model calculation of prompt neutron spectra from spontaneous fission of {sup 244}Cm and {sup 246}Cm

Energy Technology Data Exchange (ETDEWEB)

Gerasimenko, B.F. [V.G. Khlopin Radium Inst., Saint Peterburg (Russian Federation)

1997-03-01

The calculations of integral spectra of prompt neutrons of spontaneous fission of {sup 244}Cm and {sup 246}Cm were carried out. The calculations were done by the Statistical Computer Code Complex SCOFIN applying the Hauser-Feschbach method as applied to the description of the de-excitation of excited fission fragments by means of neutron emission. The emission of dipole gamma-quanta from these fragments was considered as a competing process. The average excitation energy of a fragment was calculated by two-spheroidal model of tangent fragments. The density of levels in an excited fragment was calculated by the Fermi-gas model. The quite satisfactory agreement was reached between theoretical and experimental results obtained in frames of Project measurements. The calculated values of average multiplicities of neutron number were 2,746 for {sup 244}Cm and 2,927 for {sup 246}Cm that was in a good accordance with published experimental figures. (author)

Detective quantum efficiency gains compared with speed gains for hypersensitized astronomical plates

International Nuclear Information System (INIS)

Kaye, A.L.

1977-01-01

It is reasonable to assume that gains in detective quantum efficiency (DQE) are far better criteria for assessing the performance of hypersensitizing techniques than gains in speed. It is shown here that gains in speed can be misleading, for some methods of hypersensitization give plates of increased speed but reduced detective quantum efficiency. (author)

CmMDb: a versatile database for Cucumis melo microsatellite markers and other horticulture crop research.

Science.gov (United States)

Bhawna; Chaduvula, Pavan K; Bonthala, Venkata S; Manjusha, Verma; Siddiq, Ebrahimali A; Polumetla, Ananda K; Prasad, Gajula M N V

2015-01-01

Cucumis melo L. that belongs to Cucurbitaceae family ranks among one of the highest valued horticulture crops being cultivated across the globe. Besides its economical and medicinal importance, Cucumis melo L. is a valuable resource and model system for the evolutionary studies of cucurbit family. However, very limited numbers of molecular markers were reported for Cucumis melo L. so far that limits the pace of functional genomic research in melon and other similar horticulture crops. We developed the first whole genome based microsatellite DNA marker database of Cucumis melo L. and comprehensive web resource that aids in variety identification and physical mapping of Cucurbitaceae family. The Cucumis melo L. microsatellite database (CmMDb: http://65.181.125.102/cmmdb2/index.html) encompasses 39,072 SSR markers along with its motif repeat, motif length, motif sequence, marker ID, motif type and chromosomal locations. The database is featured with novel automated primer designing facility to meet the needs of wet lab researchers. CmMDb is a freely available web resource that facilitates the researchers to select the most appropriate markers for marker-assisted selection in melons and to improve breeding strategies.

Serum Concentration of Leptin in Pregnant Adolescents Correlated with Gestational Weight Gain, Postpartum Weight Retention and Newborn Weight/Length

OpenAIRE

Reyna Sámano; Hugo Martínez-Rojano; Gabriela Chico-Barba; Estela Godínez-Martínez; Bernarda Sánchez-Jiménez; Diana Montiel-Ojeda; Maricruz Tolentino

2017-01-01

Introduction: Gestational weight gain is an important modifiable factor known to influence fetal outcomes including birth weight and adiposity. Leptin is normally correlated with adiposity and is also known to increase throughout pregnancy, as the placenta becomes a source of leptin synthesis. Several studies have reported positive correlations between cord blood leptin level and either birthweight or size for gestational age, as well as body mass index (BMI). Objective: To determine the corr...

Comparison of penile length at 6–24 months between children with unilateral cryptorchidism and a healthy normal cohort

Directory of Open Access Journals (Sweden)

Dong Soo Ryu

2018-01-01

Full Text Available Purpose: Urologic diseases affected by testosterone can be associated with smaller penis size compared to the normal population. We sought to compare penile length in children with unilateral cryptorchidism and normative data from a cohort of healthy Korean boys. Materials and Methods: This study was performed in 259 Korean boys (212, normal cohort; 47, cryptorchidism aged 6–24 months, each of whom had been brought to an outpatient clinic at one of five tertiary hospitals (Gyeongsangnam-do Province between April 2014 and June 2015. Penile length was measured via stretched penile length (SPL and testicular size was measured using orchidometry (mL. Results: SPL in children with cryptorchidism was significantly shorter compared to a cohort of healthy Korean boys aged 6–24 months (3.7±0.5 cm and 4.3±0.8 cm, p<0.001, although there were no differences with regard to height, body weight and contralateral testicular size between the two groups. According to the stratified ages (6–12, 12–18, and 18–24 months, SPL in children with cryptorchidism was persistently shorter at their ages than those without. Conclusions: It might be that the penile length aged 6–24 months of children with unilateral cryptorchidism is shorter than that of a cohort of healthy Korean boys.

Preventing Weight Gain

Science.gov (United States)

... Local Programs Related Topics Diabetes Nutrition Preventing Weight Gain Language: English (US) Español (Spanish) Recommend on Facebook ... cancer. Choosing an Eating Plan to Prevent Weight Gain So, how do you choose a healthful eating ...

Studies of population inversion and gains for xuv laser development in a recombining plasma column

International Nuclear Information System (INIS)

Milchberg, H.M.

1985-01-01

An experimental study is presented of population inversions and gains in CO 2 laser produced plasmas in a number of different solid and gas targets, with and without the presence of a magnetic field. Population inversions and gains were measured in hydrogenic carbon, CVI, and in the Li-like sequence CIV, OVI, FVII, and NeVIII. The Li-like species were easily produced in gas targets and, in general, 4d-3d population inversions were seen to increase with a combination of higher target pressure and the presence of an external magnetic field. Ratios of the 4d-3d sublevel populations ranged up to approx.10, for OVI. Inversions in CIV and FVII, in cases where solid targets were used, were less sensitive to the presence of the magnetic field. Gains in the CVI 182.17 A (3-2) line were measured using solid carbon targets, and increased in the presence of a magnetic field. The effect of placing aluminum blades near the target, for plasma cooling and faster recombination, was inconclusive. In general, gains determined by measuring an on-axis enhancement of the 182.17 A line were consistent with absolute measurements of CVI excitation-level populations. Gains of 2-4 cm -1 were measured. Axially oriented carbon-fiber targets were irradiated by the CO 2 laser, and it was found that population inversions and gain resulted only when there was no magnetic field present

A new CM SAF Solar Surface Radiation Climate Data Set derived from Meteosat Satellite Observations

Science.gov (United States)

Trentmann, J.; Mueller, R. W.; Pfeifroth, U.; Träger-Chatterjee, C.; Cremer, R.

2014-12-01

The incoming surface solar radiation has been defined as an essential climate variable by GCOS. It is mandatory to monitor this part of the earth's energy balance, and thus gain insights on the state and variability of the climate system. In addition, data sets of the surface solar radiation have received increased attention over the recent years as an important source of information for the planning of solar energy applications. The EUMETSAT Satellite Application Facility on Climate Monitoring (CM SAF) is deriving surface solar radiation from geostationary and polar-orbiting satellite instruments. While CM SAF is focusing on the generation of high-quality long-term climate data records, also operationally data is provided in short time latency within 8 weeks. Here we present SARAH (Solar Surface Radiation Dataset - Heliosat), i.e. the new CM SAF Solar Surface Radiation data set based on Meteosat satellite observations. SARAH provides instantaneous, daily- and monthly-averaged data of the effective cloud albedo (CAL), the direct normalized solar radiation (DNI) and the solar irradiance (SIS) from 1983 to 2013 for the full view of the Meteosat satellite (i.e, Europe, Africa, parts of South America, and the Atlantic ocean). The data sets are generated with a high spatial resolution of 0.05 deg allowing for detailed regional studies, and are available in netcdf-format at no cost without restrictions at www.cmsaf.eu. We provide an overview of the data sets, including a validation against reference measurements from the BSRN and GEBA surface station networks.

Studies on free electron lasers using a compact electro-static accelerator. 2. Basic specifications and estimation of the gain

International Nuclear Information System (INIS)

Kawamura, Yoshiyuki; Tanabe, Toshiya; Li, Dian-Jun; Toyoda, Koichi

1994-01-01

An experimental facility for the studies on sub-millimeter wavelength free electron lasers has been constructed using a micro-wiggler and the relativistic electron beam source described in a previous report. The pitch length, the number of periods, and the peak wiggler magnetic field strength for a gap length of 8 mm, are 12 mm, 50, and 2 kG respectively. The small signal gain as the amplifier has been estimated, and found to be high enough to overcome the loss due to coupling holes of a cavity resonator. (author)

The effect of BAPTA and 4AP in scala media on transduction and cochlear gain.

Science.gov (United States)

Sellick, P M; Robertson, D; Patuzzi, R

2006-01-01

We have injected by iontophoresis 4-amino-pyridine, a K+ channel blocker and BAPTA, (a Ca++ chelator), into scala media of the first three turns of the guinea pig cochlea. We measured the reduction in outer hair cell (OHC) receptor current, as indicated by cochlear microphonic measured in scala media evoked by a 207 Hz tone, and compared this with the elevation of the cochlear action potential (CAP) threshold. We found that in the basal turn, for frequencies between 12 and 21 kHz, CAP threshold was elevated by about 30 dB, while in the second turn, at the 3 kHz place, the maximum elevation was 15 dB. In the third turn, iontophoresis of 4AP and BAPTA reduced CM by similar amounts to that in the basal and second turn, but caused negligible elevation of CAP threshold. We conclude that the gain of the cochlear amplifier is maximal for basal turn frequencies, is halved at 3 kHz, and is reduced to close to one for frequencies below 1 kHz (no active gain). The effect of 4AP and BAPTA on neural threshold and the receptor current represented by CM may be explained by their action on OHC transduction without the involvement of IHCs.

Metformin for olanzapine-induced weight gain: a systematic review and meta-analysis.

Science.gov (United States)

Praharaj, Samir Kumar; Jana, Amlan Kusum; Goyal, Nishant; Sinha, Vinod Kumar

2011-03-01

Olanzapine is an atypical antipsychotic that is useful in schizophrenia and bipolar affective disorder, but its use is associated with troublesome weight gain and metabolic syndrome. A variety of pharmacological agents has been studied in the efforts to reverse weight gain induced by olanzapine, but current evidence is insufficient to support any particular pharmacological approach. We conducted a systematic review and meta-analysis of randomized controlled trials of metformin for the treatment of olanzapine-induced weight gain. Systematic review of the literature revealed 12 studies that had assessed metformin for antipsychotic-induced weight gain. Of these, four studies (n= 105) met the review inclusion criteria and were included in the final analysis. Meta-analysis was performed to see the effect size of the treatment on body weight, waist circumference and body-mass index (BMI). Weighted mean difference (WMD) for body weight was 5.02 (95% CI 3.93, 6.10) kg lower with metformin as compared with placebo at 12 weeks. For waist circumference, the test for heterogeneity was significant (P= 0.00002, I(2) = 85.1%). Therefore, a random effects model was used to calculate WMD, which was 1.42 (95% CI 0.29, 3.13) cm lower with metformin as compared with placebo at 12 weeks. For BMI, WMD was 1.82 (95% CI 1.44, 2.19) kg m(-2) lower with metformin as compared with placebo at 12 weeks. Existing data suggest that short term modest weight loss is possible with metformin in patients with olanzapine-induced weight gain. © 2011 The Authors. British Journal of Clinical Pharmacology © 2011 The British Pharmacological Society.

Choice of Surgical Procedure for Patients With Non-Small-Cell Lung Cancer ≤ 1 cm or > 1 to 2 cm Among Lobectomy, Segmentectomy, and Wedge Resection

DEFF Research Database (Denmark)

Dai, Chenyang; Shen, Jianfei; Ren, Yijiu

2016-01-01

PURPOSE: According to the lung cancer staging project, T1a (≤ 2 cm) non-small-cell lung cancer (NSCLC) should be additionally classified into ≤ 1 cm and > 1 to 2 cm groups. This study aimed to investigate the surgical procedure for NSCLC ≤ 1 cm and > 1 to 2 cm. METHODS: We identified 15...... multiple prognostic factors. RESULTS: OS and LCSS favored lobectomy compared with segmentectomy or wedge resection in patients with NSCLC ≤ 1 cm and > 1 to 2 cm. Multivariable analysis showed that segmentectomy and wedge resection were independently associated with poorer OS and LCSS than lobectomy...... for NSCLC ≤ 1 cm and > 1 to 2 cm. With sublobar resection, lower OS and LCSS emerged for NSCLC > 1 to 2 cm after wedge resection, whereas similar survivals were observed for NSCLC ≤ 1 cm. Multivariable analyses showed that wedge resection is an independent risk factor of survival for NSCLC > 1 to 2 cm...

Influence of core diameter and length of polymer optical fiber on Brillouin scattering properties

Science.gov (United States)

Mizuno, Yosuke; Ishigure, Takaaki; Nakamura, Kentaro

2012-02-01

Brillouin scattering in perfluorinated graded-index polymer optical fibers (PFGI-POFs) is potentially useful in developing high-accuracy distributed temperature sensors with reduced strain sensitivity. In this study, we investigate, both experimentally and theoretically, the influence of the fiber core diameter and length on the Brillouin gain spectra (BGS) in PFGI-POFs. First, we show that smaller core diameter drastically enhances the Stokes power using PFGI-POFs with 62.5-μm and 120-μm core diameters, and discuss the Brillouin threshold power. Then, we demonstrate that the PFGI-POF length has little influence on the BGS when the length is longer than 50 m. We also predict that, at 1.55-μm wavelength, it is difficult to reduce the Brillouin threshold power of PFGI-POFs below that of long silica single-mode fibers even if their core diameter is sufficiently reduced to satisfy the single-mode condition. Finally, making use of the enhanced Stokes signal, we confirm the Brillouin linewidth narrowing effect.

Length-scale dependent mechanical properties of Al-Cu eutectic alloy: Molecular dynamics based model and its experimental verification

Science.gov (United States)

Tiwary, C. S.; Chakraborty, S.; Mahapatra, D. R.; Chattopadhyay, K.

2014-05-01

This paper attempts to gain an understanding of the effect of lamellar length scale on the mechanical properties of two-phase metal-intermetallic eutectic structure. We first develop a molecular dynamics model for the in-situ grown eutectic interface followed by a model of deformation of Al-Al2Cu lamellar eutectic. Leveraging the insights obtained from the simulation on the behaviour of dislocations at different length scales of the eutectic, we present and explain the experimental results on Al-Al2Cu eutectic with various different lamellar spacing. The physics behind the mechanism is further quantified with help of atomic level energy model for different length scale as well as different strain. An atomic level energy partitioning of the lamellae and the interface regions reveals that the energy of the lamellae core are accumulated more due to dislocations irrespective of the length-scale. Whereas the energy of the interface is accumulated more due to dislocations when the length-scale is smaller, but the trend is reversed when the length-scale is large beyond a critical size of about 80 nm.

Measurement of the diffusion length of thermal neutrons in the beryllium oxide; Mesure de la longueur de diffusion des neutrons thermiques dans l'oxyde de beryllium

Energy Technology Data Exchange (ETDEWEB)

Koechlin, J C; Martelly, J; Duggal, V P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

The diffusion length of thermal neutrons in the beryllium oxide has been obtained while studying the spatial distribution of the neutrons in a massive parallelepiped of this matter placed before the thermal column of the reactor core of Saclay. The mean density of the beryllium oxide (BeO) is 2,95 gr/cm{sup 3}, the mean density of the massif is 2,92 gr/cm{sup 3}. The value of the diffusion length, deducted of the done measures, is: L = 32,7 {+-} 0,5 cm (likely gap). Some remarks are formulated about the influence of the spectral distribution of the neutrons flux used. (authors) [French] La longueur de diffusion des neutrons thermiques dans l'oxyde de beryllium a ete obtenue en etudiant la repartition spatiale des neutrons dans un massif parallelepipedique de cette matiere placee devant la colonne thermique de la Pile de Saclay. La densite moyenne de l'oxyde de beryllium (BeO) est de 2,95 gr/cm{sup 3}, la densite moyenne du massif de 2,92 gr/cm{sup 3}. La valeur de la longueur de diffusion, deduite des mesures effectuees est: L 32,7 {+-} 0,5 cm (ecart probable). Des remarques sont formulees quant a l'influence de la repartition spectrale du flux de neutrons utilise. (auteurs)

Photoluminescence decay lifetime measurements of hemicyanine derivatives of different alkyl chain lengths

International Nuclear Information System (INIS)

Shim, Taekyu; Lee, Myounghee; Kim, Sungho; Sung, Jaeho; Rhee, Bum Ku; Kim, Doseok; Kim, Hyunsung; Yoon, Kyung Byung

2004-01-01

The fluorescence upconversion setup for the detection of photoluminescence (PL) decay lifetime with subpicosecond time resolution was constructed, and the photoluminescence phenomena of several hemicyanine dyes with alkyl chains of different chain lengths tethered to the N atom of the pyridine moiety (HC-n, n=6, 15, 22) in methanol were investigated. The average decay lifetimes of the solutions determined from the measured data by multi-order exponential decay curve fitting were ∼27 ps at the PL peak wavelength. It was found that the PL decay properties did not depend on the alkyl chain length in the molecule, implying that the twist of the alkylpyridinium ring of the molecule is not possible as a nonfluorescing relaxation pathway. The time-dependent PL spectra constructed from the PL lifetime data showed the dynamic Stokes shift of ∼1000 cm -1

Influence of hydration and experimental length scale on themechanical response of human skin in vivo, using optical coherence tomography

NARCIS (Netherlands)

Hendriks, F.M.; Brokken, D.; Oomens, C.W.J.; Baaijens, F.P.T.

2004-01-01

Human skin is a complex tissue consisting of different layers. To gain better insight into the mechanical behaviour of different skin layers, the mechanical response was studied with experiments of various length scales. Also, the influence of (superficial) hydration on the mechanical response is

Size and spatial distribution of micropores in SBA-15 using CM-SANS

International Nuclear Information System (INIS)

Pollock, Rachel A.; Walsh, Brenna R.; Fry, Jason A.; Ghampson, Tyrone; Centikol, Ozgul; Melnichenko, Yuri B.; Kaiser, Helmut; Pynn, Roger; Frederick, Brian G.

2011-01-01

Diffraction intensity analysis of small-angle neutron scattering measurements of dry SBA-15 have been combined with nonlocal density functional theory (NLDFT) analysis of nitrogen desorption isotherms to characterize the micropore, secondary mesopore, and primary mesopore structure. The radial dependence of the scattering length density, which is sensitive to isolated surface hydroxyls, can only be modeled if the NLDFT pore size distribution is distributed relatively uniformly throughout the silica framework, not localized in a 'corona' around the primary mesopores. Contrast matching-small angle neutron scattering (CM-SANS) measurements, using water, decane, tributylamine, cyclohexane, and isooctane as direct probes of the size of micropores indicate that the smallest pores in SBA-15 have diameter between 5.7 and 6.2 (angstrom). Correlation of the minimum pore size with the onset of the micropore size distribution provides direct evidence that the shape of the smallest micropores is cylinderlike, which is consistent with their being due to unraveling of the polymer template.

Influence of the Particle Length of Carbon Nanotube for Pool Boiling Critical Heat Flux Enhancement of Nanofluids

International Nuclear Information System (INIS)

Park, Sung Seek; Kim, Yong Hwan; Kim, Nam Jin

2013-01-01

The results of this experiment were that the CHF of the two nanofluids increased along with the volumetric fraction until 0.001 vol%, and the two types of nanofluids are the highest CHF at 0.001 vol%. Also, the results show clearly that the rate of CHF increase of the CM-100 MWCNT nanofluid with longer-length nanoparticles is higher than that of the CM-95 MWNCT nanofluid. These results indicate that the length of carbon nanotube influences the pool boiling CHF of carbon nanotube nanofluid and that long-length MWCNT, as above-noted, offers a superior effect in this regard. Boiling heat transfer is used in a variety of industrial processes and applications, such as refrigeration, power generation, heat exchangers, cooling of high-power electronics components and cooling of nuclear reactors. The critical heat flux (CHF) phenomenon is the thermal limit during a boiling heat transfer phase change; at the CHF point the heat transfer is maximised, followed by a drastic degradation after the CHF point. The consequence is a substantial increase in wall temperature which may result in physical failure phenomenon of heat transfer systems. Therefore, the CHF is important being considered in the cooling device design, such as nuclear reactor and nuclear fuels, steam generators, high-density electronic component, etc. And, CHF enhancement is essential for safety of heat transfer system. Recently, CHF reported increased when applied to the nanofluids, with its high (higher-than-base-fluid) thermal characteristic in the nuclear power plant system. Therefore, in this study, carried out the pool boiling CHF experiments by the particle length using carbon nanotube nanofluids, and the results are compared and analyzed for the CHF enhancement. The pool boiling CHF of experiments of carbon nanotube nanofluids carried out by the length of particles and the various concentrations

Technology developments and first measurements of Low Gain Avalanche Detectors (LGAD) for high energy physics applications

International Nuclear Information System (INIS)

Pellegrini, G.; Fernández-Martínez, P.; Baselga, M.; Fleta, C.; Flores, D.; Greco, V; Hidalgo, S.; Mandić, I.; Kramberger, G.; Quirion, D.; Ullan, M.

2014-01-01

This paper introduces a new concept of silicon radiation detector with intrinsic multiplication of the charge, called Low Gain Avalanche Detector (LGAD). These new devices are based on the standard Avalanche Photo Diodes (APD) normally used for optical and X-ray detection applications. The main differences to standard APD detectors are the low gain requested to detect high energy charged particles, and the possibility to have fine segmentation pitches: this allows fabrication of microstrip or pixel devices which do not suffer from the limitations normally found [1] in avalanche detectors. In addition, a moderate multiplication value will allow the fabrication of thinner devices with the same output signal of standard thick substrates. The investigation of these detectors provides important indications on the ability of such modified electrode geometry to control and optimize the charge multiplication effect, in order to fully recover the collection efficiency of heavily irradiated silicon detectors, at reasonable bias voltage, compatible with the voltage feed limitation of the CERN High Luminosity Large Hadron Collider (HL-LHC) experiments [2]. For instance, the inner most pixel detector layers of the ATLAS tracker will be exposed to fluences up to 2×10 16 1 MeV n eq /cm 2 , while for the inner strip detector region fluences of 1×10 15 n eq /cm 2 are expected. The gain implemented in the non-irradiated devices must retain some effect also after irradiation, with a higher multiplication factor with respect to standard structures, in order to be used in harsh environments such those expected at collider experiments

Compact continuous HF microwave-discharge mixing laser

International Nuclear Information System (INIS)

Gagne, J.M.; Bertrand, L.; Conturie, Y.; Mah, S.Q.; Monchalin, J.P.

1975-01-01

The performance of a continuous chemical laser is discussed. Fluorine atoms are produced in a SF 6 + He mixture by means of a microwave-discharge apparatus that operates in a continuous mode. A maximum output power of 4 W is obtained for a 5 cm length of amplifying medium; this power output is primarily due to P transitions from the 1-0 and 2-1 bands. Weak transitions in the 3-2 band are also observed. The maximum value of measured gain is 0.11 cm -1 ; good agreement is obtained between theoretical and experimental values of gain. (auth)

Mobile Stride Length Estimation With Deep Convolutional Neural Networks.

Science.gov (United States)

Hannink, Julius; Kautz, Thomas; Pasluosta, Cristian F; Barth, Jens; Schulein, Samuel; GaBmann, Karl-Gunter; Klucken, Jochen; Eskofier, Bjoern M

2018-03-01

Accurate estimation of spatial gait characteristics is critical to assess motor impairments resulting from neurological or musculoskeletal disease. Currently, however, methodological constraints limit clinical applicability of state-of-the-art double integration approaches to gait patterns with a clear zero-velocity phase. We describe a novel approach to stride length estimation that uses deep convolutional neural networks to map stride-specific inertial sensor data to the resulting stride length. The model is trained on a publicly available and clinically relevant benchmark dataset consisting of 1220 strides from 101 geriatric patients. Evaluation is done in a tenfold cross validation and for three different stride definitions. Even though best results are achieved with strides defined from midstance to midstance with average accuracy and precision of , performance does not strongly depend on stride definition. The achieved precision outperforms state-of-the-art methods evaluated on the same benchmark dataset by . Due to the independence of stride definition, the proposed method is not subject to the methodological constrains that limit applicability of state-of-the-art double integration methods. Furthermore, it was possible to improve precision on the benchmark dataset. With more precise mobile stride length estimation, new insights to the progression of neurological disease or early indications might be gained. Due to the independence of stride definition, previously uncharted diseases in terms of mobile gait analysis can now be investigated by retraining and applying the proposed method.

Synthesis and evaluation of aqueous complexing agents for the Am/Cm separation

International Nuclear Information System (INIS)

Chapron, Simon

2014-01-01

After the reprocessing of uranium, plutonium and eventually neptunium by the PUREX process, the spent fuel is still composed of half of the periodic table. Among these elements, the main responsible for the heat of the wastes is americium. Its reprocessing could allow improving the compactness of deep geological storage of the wastes. Thus the liquid-liquid extraction process called EXAm was developed in order to recover the americium alone. The key step of the process is the Am/Cm separation. An extractant mixture is used with an aqueous complexing agent: TEDGA (N,N',N,N'-tetraethyl-diglycolamide). It allows to enhance the Am/Cm separation by keeping preferentially curium in the aqueous phase, but its structure selectivity relationship is not well known yet. Therefore, the purpose of this thesis is to synthesize and evaluate some structural analogues of TEDGA, in order to better understand the impact of its structure on the Am/Cm selectivity in the EXAm process. During this study, 14 analogues of TEDGA were synthesized and 17 molecules were evaluated in liquid-liquid extraction. Several structural modifications were studied: length and steric hindrance of the N-alkyl chains, size of the spacer, and the introduction of secondary amide functions. This work shows that it is not possible to maintain the ligand in the aqueous phase from tetrabutyl derivatives, and the addition of steric hindrance, or modification of hydrophilicity/lipophilicity balance, systematically decreases the selectivity of ligands. The addition of secondary amide functions (-CONHR) makes the molecules extractable by the solvent (formation of hydrogen bonds with the extractants), therefore they are unsuitable to be used in the EXAm process. The spacer has the main impact on the selectivity: the complexation capacity in high acid medium disappears when it is shortened (malonamide), whereas the ligand has a preference for Am instead of Cm (inversion of selectivity) when it is lengthen

Experimental investigation of a 1 kA/cm² sheet beam plasma cathode electron gun.

Science.gov (United States)

Kumar, Niraj; Pal, Udit Narayan; Pal, Dharmendra Kumar; Prajesh, Rahul; Prakash, Ram

2015-01-01

In this paper, a cold cathode based sheet-beam plasma cathode electron gun is reported with achieved sheet-beam current density ∼1 kA/cm(2) from pseudospark based argon plasma for pulse length of ∼200 ns in a single shot experiment. For the qualitative assessment of the sheet-beam, an arrangement of three isolated metallic-sheets is proposed. The actual shape and size of the sheet-electron-beam are obtained through a non-conventional method by proposing a dielectric charging technique and scanning electron microscope based imaging. As distinct from the earlier developed sheet beam sources, the generated sheet-beam has been propagated more than 190 mm distance in a drift space region maintaining sheet structure without assistance of any external magnetic field.

2-cm versus 4-cm surgical excision margins for primary cutaneous melanoma thicker than 2 mm: a randomised, multicentre trial

DEFF Research Database (Denmark)

Gillgren, Peter; Drzewiecki, Krzysztof T; Niin, Marianne

2011-01-01

Optimum surgical resection margins for patients with clinical stage IIA-C cutaneous melanoma thicker than 2 mm are controversial. The aim of the study was to test whether survival was different for a wide local excision margin of 2 cm compared with a 4-cm excision margin....

The impact of channel path length on PEMFC flow-field design

Energy Technology Data Exchange (ETDEWEB)

Shimpalee, S.; Greenway, S.; Van Zee, J.W. [Chemical Engineering Department, University of South Carolina, Columbia, SC 29208 (United States)

2006-09-29

Distributions in reactant species concentration in a PEMFC due to local consumption of fuel and local transport of water through the membrane cause distributions in current density, temperature, and water concentration in three dimensions in a PEMFC. These distributions can lead to flooding or drying of the membrane that may shorten the life of an MEA. Changing the cell's flow-field pattern to distribute the gas more evenly is one method of minimizing these stresses. This paper investigates how 200cm{sup 2} serpentine flow-fields with different number of gas paths, and thus different gas path lengths, affect performance and species distribution. The results show how the local temperature, water content, and current density distributions become more uniform for serpentine flow-field designs with shorter path lengths or larger number of channels. These results may be used to develop universal heuristics and dimensionless number correlations in the design of flow-fields and stacks. (author)

Value of 18FDG PET-CT in defining the length of esophageal cancer

International Nuclear Information System (INIS)

Yuan Shuanghu; Yu Jinming; Yu Yonghua; Yang Xinhua; Chen Shaoqing; Fu Zheng; Yang Guoren; Guo Hongbo; Wang Xiaohang; Zhou Yingzhi

2006-01-01

Objective: To assess the value of 18-fluoro-deoxy-glucose positron emission-CT (FDG PET-CT) in defining the length of primary esophageal cancer. Methods: Thirty-two patients had undergone esophagoscopy, esophagography and FDG PET-CT scans one week before esophagectomy. There was one tumor located in the upper thoracic esophagus, 22 in the middle thoracic esophagus, and 9 in the lower thoracic esophagus. The location and length of primary lesion of the tumor was determined by esophagoscopy, esophagography, and FDG PET-CT. The length of the abnormality seen on the CT portion of the PET-CT scan was determined separately and independently by two radiologists. All results were compared with the resected specimen. Results: According to esophagography, CT and PET-CT, all lesion lengths were compared with that of the resected specimen. It was found that the tumor location determined by esophagoscopy was not in accordance with the resected specimen in 2 patients. The mean length of the primary tumor, being from short to long, were (3.8±1.4),(4.1±1.5),(4.4±1.6),(5.3±1.9) and (4.7±1.7) cm, as determined by esophagoscopy, esophagography, CT, actral length of the resected specimen and PET-CT. Compared with the resected specimen,there was obvious difference (P=0.000, 0.007, 0.025, 0.001). Considering that there might be some kind of shrinkage in the resected specimen (about 83.59%, as reported by Ma et al), we rectified the length of resected specimen and compared with other findings again. It was found that insignificant difference existed between PET-CT and rectified length value of the resected specimen (P=0.082). Conclusions: FDG PET-CT is effective in the length determination of primary esophageal cancer. It may be used to determine the length of esophagus to be resected for patients indicated for esophagectomy. It may also be used to accurately delineate the gross tumor volume for patients eligible for radiotherapy. (authors)

Vergence increases the gain of the human angular vestibulo-ocular reflex during peripheral hyposensitivity elicited by cold thermal irrigation.

Science.gov (United States)

Tamás, László T; Lundberg, Yunxia W; Büki, Béla

2018-01-01

When viewing a far target, the gain of the horizontal vestibulo-ocular reflex (VOR) is around 1.0, but when viewing a near target there is an increased response. It has been shown that while this convergence-mediated modulation is unaffected by canal plugging and clinically practical transmastoid galvanic stimulation, it is eliminated by a partial peripheral gentamicin lesion. The aim of this study was to determine if convergence increases the gain during peripheral hyposensitivity elicited by cold thermal irrigation. The high frequency VOR gain was measured using video head impulse testing immediately after the cold caloric stimulus in 9 healthy human subjects with the lateral semicircular canals oriented approximately earth-vertical. Before caloric irrigation, near viewing (15 cm) increased the average VOR gain by 28% (from 1 to 1.28). Cold (24°C) water irrigation of the right ear decreased the gain to 0.66 (far viewing) and 0.82 (near viewing) (22% difference). Although vergence also increased the gain for impulses to the left to the same degree before caloric stimulus, the caloric irrigation itself (applied to the right ear) did not influence the gain for contralateral impulses. In our experiments vergence increased the gain of the human angular VOR during peripheral hyposensitivity elicited by cold thermal irrigation. These results suggest that cold irrigation does not abolish the function of the nonlinear/phasic vestibular afferent pathway.

Work, Train, Win: Work-Based Learning Design and Management for Productivity Gains. OECD Education Working Papers, No. 135

Science.gov (United States)

Kis, Viktoria

2016-01-01

Realising the potential of work-based learning schemes as a driver of productivity requires careful design and support. The length of work-based learning schemes should be adapted to the profile of productivity gains. A scheme that is too long for a given skill set might be unattractive for learners and waste public resources, but a scheme that is…

Telomere length analysis.

Science.gov (United States)

Canela, Andrés; Klatt, Peter; Blasco, María A

2007-01-01

Most somatic cells of long-lived species undergo telomere shortening throughout life. Critically short telomeres trigger loss of cell viability in tissues, which has been related to alteration of tissue function and loss of regenerative capabilities in aging and aging-related diseases. Hence, telomere length is an important biomarker for aging and can be used in the prognosis of aging diseases. These facts highlight the importance of developing methods for telomere length determination that can be employed to evaluate telomere length during the human aging process. Telomere length quantification methods have improved greatly in accuracy and sensitivity since the development of the conventional telomeric Southern blot. Here, we describe the different methodologies recently developed for telomere length quantification, as well as their potential applications for human aging studies.

Uncertainty Analysis of Consequence Management (CM) Data Products.

Energy Technology Data Exchange (ETDEWEB)

Hunt, Brian D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eckert-Gallup, Aubrey Celia [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cochran, Lainy Dromgoole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kraus, Terrence D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fournier, Sean Donovan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Allen, Mark B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schetnan, Richard Reed [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Simpson, Matthew D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Okada, Colin E. [Remote Sensing Lab. (RSL), Nellis AFB, Las Vegas, NV (United States); Bingham, Avery A. [Remote Sensing Lab. (RSL), Nellis AFB, Las Vegas, NV (United States)

2018-01-01

The goal of this project is to develop and execute methods for characterizing uncertainty in data products that are deve loped and distributed by the DOE Consequence Management (CM) Program. A global approach to this problem is necessary because multiple sources of error and uncertainty from across the CM skill sets contribute to the ultimate p roduction of CM data products. This report presents the methods used to develop a probabilistic framework to characterize this uncertainty and provides results for an uncertainty analysis for a study scenario analyzed using this framework.

Laser threshold and optical gain of blue optically pumped InGaN/GaN multiple quantum wells (MQW) grown on Si

International Nuclear Information System (INIS)

Lutsenko, E.V.; Danilchyk, A.V.; Tarasuk, N.P.; Andryieuski, A.V.; Pavlovskii, V.N.; Gurskii, A.L.; Yablonskii, G.P.; Kalisch, H.; Jansen, R.H.; Dikme, Y.; Schineller, B.; Heuken, M.

2008-01-01

Optical and laser properties of a series of MQW heterostructures with varying geometry grown on silicon with Al predeposition were investigated. Photoluminescence (PL) band positions covered a spectral range of 430-460 nm under I exc =1 MW/cm 2 and 445-505 nm under I exc =0.15 W/cm 2 . Laser action was achieved under transversal optical pumping at room temperature using only cleaved lateral facets of the samples as laser mirrors. The laser threshold rose from 137 kW/cm 2 to 300 kW/cm 2 with laser wavelength increase from 440 nm to 465 nm. Numerical simulation of the laser conditions shows that the minimal threshold is realized on the fifth order mode. However, the calculated value of material optical gain of InGaN at the laser threshold increases only from 750 cm -1 to 1020 cm -1 , mainly due to absorption rise in the substrate with increasing wavelength. Correlation was observed between PL characteristics and laser threshold. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Measurements of higher order modes in a 30 cm long X-band structure

International Nuclear Information System (INIS)

Xiao, L.; Liang, Y.; Tong, D.; Zhang, H.

2001-01-01

The use of a cage of metallic wires as a bead is proposed to measure the higher order modes (HOMs) in an X-band accelerating structure. These long thin wires can isolate the longitudinal electric field component from other field components and produce sufficient frequency shift in bead-pull measurements. In the setup described in this paper, the bead is made by sputtering silver film onto a thin nylon line through a specially designed fixture. The cage has a size of approximately 0.5 mm in diameter, 2 mm in length and more than six metallic wires of less than 0.1 mm in width. The fabrication and calibration of the cage are described. The longitudinal electric fields of the lowest passband dipole mode TM 110 in a 30 cm long X-band structure are measured by bead-pull measurements. Results are compared with the calculated ones obtained from URMELT-code

Broad bandwidth and 600 μm length photonic crystal fiber polarization filter at the communication window of 1.55 μm

Science.gov (United States)

Zhang, Zhen; Li, Shuguang; Liu, Qiang; Zhang, Shuhuan; Wang, Yujun; Wu, Junjun

2018-02-01

A broad bandwidth and 600-μm length photonic crystal fiber polarization filter at the communication window of 1.55 μm is proposed. The physical parameters are analyzed by the finite element method. In the structure, the loss is 705.81 dB/cm for y-polarized mode and 24.06 dB/cm for x-polarized mode at the wavelength of 1.55 μm; the y-polarized mode will be filtered out because of this property. The bandwidth of an extinction ratio (ER) better than -20 dB is 65 nm when the filter length is 600 μm, and the ER is -41 dB at the communication wavelength of 1.55 μm. The filter structure is simple and easy to produce, and it can be used to produce a single-polarization filter.

Digital Radiography for Determination of Primary Tooth Length: In Vivo and Ex Vivo Studies

Directory of Open Access Journals (Sweden)

Maria D. Basso

2015-01-01

Full Text Available Background. Methods for determining the root canal length of the primary tooth should yield accurate and reproducible results. In vitro studies show some limitations, which do not allow their findings to be directly transferred to a clinical situation. Aim. To compare the accuracy of radiographic tooth length obtained from in vivo digital radiograph with that obtained from ex vivo digital radiograph. Method. Direct digital radiographs of 20 upper primary incisors were performed in teeth (2/3 radicular resorption that were radiographed by an intraoral sensor, according to the long-cone technique. Teeth were extracted, measured, and mounted in a resin block, and then radiographic template was used to standardise the sensor-target distance (30 cm. The apparent tooth length (APTL was obtained from the computer screen by means of an electronic ruler accompanying the digital radiography software (CDR 2.0, whereas the actual tooth length (ACTL was obtained by means of a digital calliper following extraction. Data were compared to the ACTL by variance analysis and Pearson’s correlation test. Results. The values for APTL obtained from in vivo radiography were slightly underestimated, whereas those values obtained from ex vivo were slightly overestimated. No significance was observed (P≤0.48 between APTL and ACTL. Conclusion. The length of primary teeth estimated by in vivo and ex vivo comparisons using digital radiography was found to be similar to the actual tooth length.

Characterizing transport current defects in 1-cm-wide YBa[sub 2]Cu[sub 3]O[sub 7-delta] coated conductors.

Energy Technology Data Exchange (ETDEWEB)

Brown, G. W. (Geoffrey W.); Hawley, M. E. (Marilyn E.); Peterson, E. J. (Eric J.); Coulter, J. Y. (James Y.); Dowden, P. C. (Paul C.); Arendt, P. N. (Paul N.); Foltyn, S. R. (Stephen R.); Mueller, F. M. (Fred M.)

2001-01-01

We have used a low temperature magnetic imaging system to determine current pathways in 5 cm long 'good' and 'bad' regions of a 1-cm-wide YBa2Cu3O7-{delta} coated conductor. The good and bad regions were identified with 4 point probe measurements taken at 1 cm intervals along the tape length. The current density map from the good region showed the expected edge peaked structure, similar to that seen in previous work on high quality test samples grown on single crystal substrates. The structure was also consistent with theoretical understanding of thin film superconductors where demagnetizing effects are strong. The maps from the bad region showed that the current was primarily confined to the right half of the sample. The left half carried only a small current that reached saturation quickly. Effectively halving the sample width quantitatively explains the critical current measured in that section. Spatially resolved xray analysis with 1 mm resolution was used to further characterize the bad section and suggested an abnormally large amount of a-axis YBCO present. This may be the result of non-uniform heating leading to a low deposition temperature in that area.

Influence of repair length on residual stress in the repair weld of a clad plate

International Nuclear Information System (INIS)

Jiang Wenchun; Xu, X.P.; Gong, J.M.; Tu, S.T.

2012-01-01

Highlights: ► Residual stress in the repair weld of a stainless steel clad plate is investigated. ► The effect of repair length on residual stress has been studied. ► Large tensile residual stress is generated in the repair weld and heat affected zone. ► With the increase of repair length, transverse stress is decreased. ► Repair length has little effect on longitudinal stress. - Abstract: A 3-D sequential coupling finite element simulation is performed to investigate the temperature field and residual stress in the repair weld of a stainless steel clad plate. The effect of repair length on residual stress has been studied, aiming to provide a reference for repairing the cracked clad plate. The results show that large tensile residual stresses are generated in the repair weld and heat affected zone (HAZ), and then decrease gradually away from the weld and HAZ. The residual stresses through thickness in the clad layer are relative uniform, while they are non-uniform in the base metal. A discontinuous stress distribution is generated across the interface between weld metal and base metal. The repair length has a great effect on transverse stress. With the increase of repair length, the transverse stress is decreased. When the repair length is increased to 14 cm, the peak of transverse stress has been decreased below yield strength, and the transverse stress in the weld and HAZ has also been greatly decreased. But the repair length has little effect on longitudinal stress.

POSSIBILITY OF STEM GAIN OF NATIVE EUXYLOPHOROUS SPECIES FROM THE CENTRAL REGION OF RIO GRANDE DO SUL

Directory of Open Access Journals (Sweden)

Rodrigo Borges de Mattos

2010-08-01

Full Text Available The present work was developed to observe and quantify the possibility of stem gain in five native euxylophorous species [Angico (Parapiptadenia rigida, Canjerana (Cabralea canjerana, Cedro (Cedrela fissilis, Grápia (Apuleia leiocarpa, and Louro (Cordia trichotoma] in non managed native forests of São João do Polêsine municipality, state of RS. There were studied 17 temporary plots of 10 x 100 m. In the trees of the five elected species for this study, that presented diameter at breast height (dbh larger than 5 cm, the total height, the commercial height and the potential commercial height of the stems were measured.  The stem gain was defined as the difference between the current and potential commercial height, in relation to current commercial height and was expressed in percentage. The average percentile of shaft gain for all the species was larger than 70%, while Louro showed a stem gain significantly smaller than the other species. By a regression analysis (stepwise procedure, mathematical models were selected to describe the stem gain of each species and all the species together. The results showed that there is a potenctial for value adding to the native forest formations of the area, not yet explored by silviculture practices.

Fabrication and performance analysis of 4-sq cm indium tin oxide/InP photovoltaic solar cells

Science.gov (United States)

Gessert, T. A.; Li, X.; Phelps, P. W.; Coutts, T. J.; Tzafaras, N.

1991-01-01

Large-area photovoltaic solar cells based on direct current magnetron sputter deposition of indium tin oxide (ITO) into single-crystal p-InP substrates demonstrated both the radiation hardness and high performance necessary for extraterrestrial applications. A small-scale production project was initiated in which approximately 50 ITO/InP cells are being produced. The procedures used in this small-scale production of 4-sq cm ITO/InP cells are presented and discussed. The discussion includes analyses of performance range of all available production cells, and device performance data of the best cells thus far produced. Additionally, processing experience gained from the production of these cells is discussed, indicating other issues that may be encountered when large-scale productions are begun.

Normative data for stretched penile length in term neonates born in Tamil Nadu.

Science.gov (United States)

Prabhu, Sudha Rathna; Mahadevan, Shriraam; Bharath, R; Jagadeesh, Sujatha; Kumutha, J; Suresh, Seshadri

2014-07-01

To establish normative data for stretched penile length (SPL) in term male neonates born in Tamil Nadu. All live term male neonates delivered in a hospital during a given period were included. SPL was measured from the pubic ramus to the tip of the glans. Two consecutive measurements were taken and average was recorded. The mean SPL observed in our study was 2.83 ± 0.49 cm. This study helps establish normative values for SPL in neonates of Tamil Nadu origin.

Active rc filter permits easy trade-off of amplifier gain and sensitivity to gain

Science.gov (United States)

Kerwin, W. J.; Shaffer, C. V.

1968-01-01

Passive RC network was designed with zeros of transmission in the right half of the complex frequency plane in the feedback loop of a simple negative-gain amplifier. The proper positioning provides any desired trade-off between amplifier gain and sensitivity to amplifier gain.

Genetic Mutations, Birth Lengths, Weights and Head Circumferences of Children with IGF-I Receptor Defects. Comparison with other Congenital Defects in the GH/IGF-I axis.

Science.gov (United States)

Essakow, Jenna Lee; Lauterpacht, Aharon; Lilos, Pearl; Kauli, Rivka; Laron, Zvi

2016-09-01

In recent years more and more genetic defects along the GHRH-GH-IGF-I axis have been reported. Mutations of the IGF-I receptor (R) are a rare abnormality of whom only the heterozygote progenies survive. To summarize, from the literature, data on birth length, weight and head circumference of neonates with IGF-I-R mutations, and to correlate the data with that of other types of mutations in the GH/IGF-I axis. Sixty seven neonates from 24 published articles were included and forty seven different mutations of the IGF-I (R) located on chromosome 15 have been identified. Mean (±SD) birth length (BL), available for 26, (10 M, 16F) neonates with a gestational age of 34-41weeks, was 44.2±4cm; one was premature (30cm at 31 weeks). There was a significant correlation between birth length and gestational age (GA) r=0.71 (p>.001). Mean birth weight (BW) of 41 neonates (18M, 23F) was 2388±743gr. Two premature neonates weighed 650gr and 950gr respectively. The BW correlated significantly with gestational age, (males: r=0.68; p=0.007, females: r=0.49; p=0.024). The BMI of 25 neonates ranged from 6 to 13. In 22 records marked microcephaly was ascertained or stated. Nine of 16 mothers were short (133 -148cm), m±SD = 150.5±7.3cm. Copyright© of YS Medical Media ltd.

Gate length variation effect on performance of gate-first self-aligned In₀.₅₃Ga₀.₄₇As MOSFET.

Science.gov (United States)

Mohd Razip Wee, Mohd F; Dehzangi, Arash; Bollaert, Sylvain; Wichmann, Nicolas; Majlis, Burhanuddin Y

2013-01-01

A multi-gate n-type In₀.₅₃Ga₀.₄₇As MOSFET is fabricated using gate-first self-aligned method and air-bridge technology. The devices with different gate lengths were fabricated with the Al2O3 oxide layer with the thickness of 8 nm. In this letter, impact of gate length variation on device parameter such as threshold voltage, high and low voltage transconductance, subthreshold swing and off current are investigated at room temperature. Scaling the gate length revealed good enhancement in all investigated parameters but the negative shift in threshold voltage was observed for shorter gate lengths. The high drain current of 1.13 A/mm and maximum extrinsic transconductance of 678 mS/mm with the field effect mobility of 364 cm(2)/Vs are achieved for the gate length and width of 0.2 µm and 30 µm, respectively. The source/drain overlap length for the device is approximately extracted about 51 nm with the leakage current in order of 10(-8) A. The results of RF measurement for cut-off and maximum oscillation frequency for devices with different gate lengths are compared.

Gate Length Variation Effect on Performance of Gate-First Self-Aligned In0.53Ga0.47As MOSFET

Science.gov (United States)

Mohd Razip Wee, Mohd F.; Dehzangi, Arash; Bollaert, Sylvain; Wichmann, Nicolas; Majlis, Burhanuddin Y.

2013-01-01

A multi-gate n-type In0.53Ga0.47As MOSFET is fabricated using gate-first self-aligned method and air-bridge technology. The devices with different gate lengths were fabricated with the Al2O3 oxide layer with the thickness of 8 nm. In this letter, impact of gate length variation on device parameter such as threshold voltage, high and low voltage transconductance, subthreshold swing and off current are investigated at room temperature. Scaling the gate length revealed good enhancement in all investigated parameters but the negative shift in threshold voltage was observed for shorter gate lengths. The high drain current of 1.13 A/mm and maximum extrinsic transconductance of 678 mS/mm with the field effect mobility of 364 cm2/Vs are achieved for the gate length and width of 0.2 µm and 30µm, respectively. The source/drain overlap length for the device is approximately extracted about 51 nm with the leakage current in order of 10−8 A. The results of RF measurement for cut-off and maximum oscillation frequency for devices with different gate lengths are compared. PMID:24367548

Comprimento da estaca e tipo de substrato na propagação vegetativa de atroveran Shoot cutting length and substrate types on vegetative propagation of atroveran

Directory of Open Access Journals (Sweden)

Larissa Corrêa do Bomfim Costa

2007-08-01

Full Text Available A propagação vegetativa de espécies medicinais vem despertando interesse das pesquisas agronômicas, uma vez que se constitui no ponto de partida e em ferramenta básica para qualquer cultivo em escala comercial. Este trabalho objetivou determinar o comprimento de estaca e o tipo de substrato mais adequados para a propagação vegetativa de atroveran. Em condições de casa de vegetação sob nebulização intermitente, foram testados dois comprimentos de estacas (10 e 20cm e três substratos (areia lavada, casca de arroz carbonizada e substrato comercial Plantmax®, em delineamento experimental em blocos casualizados, com quatro repetições e cinco estacas por parcela. Aos trinta e cinco dias, foram avaliados a porcentagem de enraizamento, o comprimento da maior raiz (cm e a biomassa seca das folhas e das raízes (mg. Os resultados indicaram que a propagação vegetativa de atroveran por meio de estaquia é viável, uma vez que o seu enraizamento médio ficou acima de 70%. As mudas de atroveran obtidas de estacas com 20cm apresentaram maior biomassa seca das folhas e das raízes, apesar de o comprimento da estaca não ter afetado a porcentagem de enraizamento e o comprimento da raiz. Os tipos de substrato não proporcionaram efeito sobre o desenvolvimento das estacas de atroveran. Recomenda-se a produção de mudas de atroveran com estacas de 20cm de comprimento, utilizando-se qualquer um dos três substratos testados.The vegetative propagation of medicinal species is in increasing agronomic interest because it is the starting point and a basic tool for any cultivation in commercial scale. The objective of this work was to determine the best shoot cutting length and the best substrate for vegetative propagation of Ocimum selloi. Cuttings were placed in greenhouse conditions under intermittent mist. Two cutting sizes (10 and 20cm and three substrate types (washed sand, carbonized rice hulls and commercial substrate Plantmax® were tested

FOREGROUND MODEL AND ANTENNA CALIBRATION ERRORS IN THE MEASUREMENT OF THE SKY-AVERAGED λ21 cm SIGNAL AT z∼ 20

Energy Technology Data Exchange (ETDEWEB)

Bernardi, G. [SKA SA, 3rd Floor, The Park, Park Road, Pinelands, 7405 (South Africa); McQuinn, M. [Department of Astronomy, University of California, Berkeley, CA 94720 (United States); Greenhill, L. J., E-mail: gbernardi@ska.ac.za [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States)

2015-01-20

The most promising near-term observable of the cosmic dark age prior to widespread reionization (z ∼ 15-200) is the sky-averaged λ21 cm background arising from hydrogen in the intergalactic medium. Though an individual antenna could in principle detect the line signature, data analysis must separate foregrounds that are orders of magnitude brighter than the λ21 cm background (but that are anticipated to vary monotonically and gradually with frequency, e.g., they are considered {sup s}pectrally smooth{sup )}. Using more physically motivated models for foregrounds than in previous studies, we show that the intrinsic spectral smoothness of the foregrounds is likely not a concern, and that data analysis for an ideal antenna should be able to detect the λ21 cm signal after subtracting a ∼fifth-order polynomial in log ν. However, we find that the foreground signal is corrupted by the angular and frequency-dependent response of a real antenna. The frequency dependence complicates modeling of foregrounds commonly based on the assumption of spectral smoothness. Our calculations focus on the Large-aperture Experiment to detect the Dark Age, which combines both radiometric and interferometric measurements. We show that statistical uncertainty remaining after fitting antenna gain patterns to interferometric measurements is not anticipated to compromise extraction of the λ21 cm signal for a range of cosmological models after fitting a seventh-order polynomial to radiometric data. Our results generalize to most efforts to measure the sky-averaged spectrum.

Multi-level multi-thermal-electron FDTD simulation of plasmonic interaction with semiconducting gain media: applications to plasmonic amplifiers and nano-lasers.

Science.gov (United States)

Chen, X; Bhola, B; Huang, Y; Ho, S T

2010-08-02

Interactions between a semiconducting gain medium and confined plasmon-polaritons are studied using a multilevel multi-thermal-electron finite-difference time-domain (MLMTE-FDTD) simulator. We investigated the amplification of wave propagating in a plasmonic metal-semiconductor-metal (MSM) waveguide filled with semiconductor gain medium and obtained the conditions required to achieve net optical gain. The MSM gain waveguide is used to form a plasmonic semiconductor nano-ring laser(PSNRL) with an effective mode volume of 0.0071 microm3, which is about an order of magnitude smaller than the smallest demonstrated integrated photonic crystal based laser cavities. The simulation shows a lasing threshold current density of 1kA/cm2 for a 300 nm outer diameter ring cavity with 80 nm-wide ring. This current density can be realistically achieved in typical III-V semiconductor, which shows the experimental feasibility of the proposed PSNRL structure.

An output amplitude configurable wideband automatic gain control with high gain step accuracy

International Nuclear Information System (INIS)

He Xiaofeng; Ye Tianchun; Mo Taishan; Ma Chengyan

2012-01-01

An output amplitude configurable wideband automatic gain control (AGC) with high gain step accuracy for the GNSS receiver is presented. The amplitude of an AGC is configurable in order to cooperate with baseband chips to achieve interference suppression and be compatible with different full range ADCs. And what's more, the gain-boosting technology is introduced and the circuit is improved to increase the step accuracy. A zero, which is composed by the source feedback resistance and the source capacity, is introduced to compensate for the pole. The AGC is fabricated in a 0.18 μm CMOS process. The AGC shows a 62 dB gain control range by 1 dB each step with a gain error of less than 0.2 dB. The AGC provides 3 dB bandwidth larger than 80 MHz and the overall power consumption is less than 1.8 mA, and the die area is 800 × 300 μm 2 . (semiconductor integrated circuits)

Psoas muscle architectural design, in vivo sarcomere length range, and passive tensile properties support its role as a lumbar spine stabilizer.

Science.gov (United States)

Regev, Gilad J; Kim, Choll W; Tomiya, Akihito; Lee, Yu Po; Ghofrani, Hossein; Garfin, Steven R; Lieber, Richard L; Ward, Samuel R

2011-12-15

Controlled laboratory and cross-sectional study designs. To determine psoas major (PM) muscle architectural properties, in vivo sarcomere-length operating range, and passive mechanical properties. PM is an important hip flexor but its role in lumbar spine function is not fully understood. Several investigators have detailed the gross anatomy of PM, but comprehensive architectural data and in vivo length-tension and passive mechanical behaviors have not been documented. PM was isolated in 13 cadaver specimens, permitting architectural measurements of physiological cross-sectional area (PCSA), normalized fiber length (Lf), and Lf:muscle length (Lm) ratio. Sarcomere lengths were measured in vivo from intraoperative biopsies taken with the hip joint in flexed and extended positions. Single-fiber and fiber bundle tensile properties and titin molecular weight were then measured from separate biopsies. Architecturally, average PCSA was 18.45 ± 1.32 cm2, average Lf was 12.70 ± 2 cm, and average Lf: Lm was 0.48 ± 0.06. Intraoperative sarcomere length measurements revealed that the muscle operates from 3.18 ± 0.20 μm with hip flexed at 10.7° ± 13.9° to 3.03 ± 0.22 μm with hip flexed at 55.9° ± 21.4°. Passive mechanical data demonstrated that the elastic modulus of the PM muscle fibers was 37.44 ± 9.11 kPa and of fiber bundles was 55.3 ± 11.8 kPa. Analysis of PM architecture demonstrates that its average Lf and passive biomechanical properties resemble those of the lumbar erector spinae muscles. In addition, PM sarcomere lengths were confined to the descending portion of the length-tension curve allowing the muscle to become stronger as the hip is flexed and the spine assumes a forward leaning posture. These findings suggest that the human PM has architectural and physiologic features that support its role as both a flexor of the hip and a dynamic stabilizer of the lumbar spine.

Robust Foregrounds Removal for 21-cm Experiments

Science.gov (United States)

Mertens, F.; Ghosh, A.; Koopmans, L. V. E.

2018-05-01

Direct detection of the Epoch of Reionization via the redshifted 21-cm line will have unprecedented implications on the study of structure formation in the early Universe. To fulfill this promise current and future 21-cm experiments will need to detect the weak 21-cm signal over foregrounds several order of magnitude greater. This requires accurate modeling of the galactic and extragalactic emission and of its contaminants due to instrument chromaticity, ionosphere and imperfect calibration. To solve for this complex modeling, we propose a new method based on Gaussian Process Regression (GPR) which is able to cleanly separate the cosmological signal from most of the foregrounds contaminants. We also propose a new imaging method based on a maximum likelihood framework which solves for the interferometric equation directly on the sphere. Using this method, chromatic effects causing the so-called ``wedge'' are effectively eliminated (i.e. deconvolved) in the cylindrical (k⊥, k∥) power spectrum.

Gain attenuation of gated framing camera

International Nuclear Information System (INIS)

Xiao Shali; Liu Shenye; Cao Zhurong; Li Hang; Zhang Haiying; Yuan Zheng; Wang Liwei

2009-01-01

The theoretic model of framing camera's gain attenuation is analyzed. The exponential attenuation curve of the gain along the pulse propagation time is simulated. An experiment to measure the coefficient of gain attenuation based on the gain attenuation theory is designed. Experiment result shows that the gain follows an exponential attenuation rule with a quotient of 0.0249 nm -1 , the attenuation coefficient of the pulse is 0.00356 mm -1 . The loss of the pulse propagation along the MCP stripline is the leading reason of gain attenuation. But in the figure of a single stripline, the gain dose not follow the rule of exponential attenuation completely, instead, there is a gain increase at the stripline bottom. That is caused by the reflection of the pulse. The reflectance is about 24.2%. Combining the experiment and theory, which design of the stripline MCP can improved the gain attenuation. (authors)

THE EFFECT OF FERMENTED OIL PALM FRONDS IN DIET ON BODY WEIGHT GAIN AND MEAT QUALITY OF GOAT

Directory of Open Access Journals (Sweden)

E. Musnandar

2014-10-01

Full Text Available The aims of study were to evaluate the use of fermented of oil palm fronds (FOPF on body weightgain and meat quality of goat. This experiment was arranged in Completely Randomized Design with 3treatments i.e. R1 (grass 0%: FOPF 100%, R2 (grass 50%: FOPF 50% and R3 (grass 100%: FOPF 0%and 5 replications. The parameters of the study were feed intake, average daily gain (ADG, weight andpercentage of carcass and meat quality. The results indicated that feed intake and meat quality of goatwas not affected by treatment, but the average daily gain, carcass weight, and percentage of carcass, wasaffected by the differences of percentage of FOPF in the pellet complete feed. The best ration was in theR1 ration (grass 0%: FOPF 100% that significantly different (P<0.05 from the other rations. The feedintake tended to be higher in goat fed R1 (895.87 g/d compared to those in goat with the R2 (854.38g/d and R3 (851.53 g/d. The average daily gain and carcass weight were higher in goat fed R1 rationcompared to those in goat fed R2 and R3. Consequently, the carcass percentage in R1 was higher thanthose in R2 and R3. The carcass percentage was ranged from 38.41-41.38%. The Ribeye area was higherin goat fed R1 (9.73 cm2 than R2 (8.34 cm2 and R3 (7.76 cm2. In this study, the protein content ofgoat meat was ranged from 19.06 to 20.71%, lipid content was ranged from 0.703 to 1.106% and watercontent was range from 72.45% to 74.12%, in which were not different among the treatments. It can beconcluded that the use of FOPF in a complete feed could improve performance and meat quality of goat.

Weight Gain during Pregnancy

Science.gov (United States)

... Global Map Premature Birth Report Cards Careers Archives Pregnancy Before or between pregnancies Nutrition, weight & fitness Prenatal ... fitness > Weight gain during pregnancy Weight gain during pregnancy E-mail to a friend Please fill in ...

Carbothermic synthesis of (Cm,Pu)N

International Nuclear Information System (INIS)

Takano, Masahide; Itoh, Akinori; Akabori, Mitsuo; Ogawa, Toru; Numata, Masami; Okamoto, Hisato

2001-01-01

Nitrides are being considered as fuel candidates for the transmutation of minor actinides. Carbothermic reduction of oxides is an effective method to fabricate nitride fuels. In this study, (Cm 0.40 ,Pu 0.60 )N was synthesized by the carbothermic reduction of the mixed oxide in N 2 . By applying excess carbon, an oxide-free nitride was obtained at 1773 K. The lattice parameter of the oxide-free sample was 0.4948 nm, and that of the nitride with oxides was 0.4974 nm. The former value agreed well with that estimated from the literature values for CmN and PuN. The larger lattice parameter of the latter sample is considered to be due to the oxygen dissolved in the nitride. (authors)

The influence of quantum-dash height on the differential gain and linewidth enhancement factor of InAs/InP quantum-dash lasers

KAUST Repository

Khan, Mohammed Zahed Mustafa

2010-12-01

We present a rate equation model for the analysis of static and dynamic characteristics of InAs/InP quantumdash (Qdash) semiconductor laser. The model is applied to calculate the differential modal gain (DMG) and linewidth enhancement factor (LEF) of the Qdash laser. In addition, the effect of varying the Qdash height on these dynamic parameters is evaluated. The model predicts a decrease in the differential modal gain with increase in the Qdash height while the LEF value generally does not get affected. The LEF and DMG of the Qdash laser at peak gain attain a value of ∼1-1.5 and ∼0.6×10 -15 -1.0×10-15 cm2, respectively. © 2010 IEEE.

The influence of quantum-dash height on the differential gain and linewidth enhancement factor of InAs/InP quantum-dash lasers

KAUST Repository

Khan, Mohammed Zahed Mustafa; Ng, Tien Khee; Schwingenschlö gl, Udo; Ooi, Boon S.

2010-01-01

We present a rate equation model for the analysis of static and dynamic characteristics of InAs/InP quantumdash (Qdash) semiconductor laser. The model is applied to calculate the differential modal gain (DMG) and linewidth enhancement factor (LEF) of the Qdash laser. In addition, the effect of varying the Qdash height on these dynamic parameters is evaluated. The model predicts a decrease in the differential modal gain with increase in the Qdash height while the LEF value generally does not get affected. The LEF and DMG of the Qdash laser at peak gain attain a value of ∼1-1.5 and ∼0.6×10 -15 -1.0×10-15 cm2, respectively. © 2010 IEEE.

Laser-induced flourescence studies of Cm3+ complexes in solution

International Nuclear Information System (INIS)

Beitz, J.V.

1989-01-01

Photophysical studies of complexed Cm 3 + in solution have been carried out using a laser-induced fluorescence method. The luminescence decay rate of the first excited J=7/2 state of Cm 3 + was measured using carbonate, nitrate, and two extractant aminocarboxylic acids as complexing ligands in aqueous solution. Cm(ClO 4 ) 3 dissolved in methyl sulfoxide also was studied. Solvent deuteration provided insight into the dominant nonradiative luminescence quenching mechanism which was found to be electronic-to- vibrational energy transfer. Emission spectra of Cm 3 + complexed by the various ligands studied are reported. Prior spectroscopic and photophysical studies of Cm 3 + in solution are reviewed. 24 refs. , 2 figs., 1 tab

Commissioning of an electro-optic electron bunch length monitor at FLASH

International Nuclear Information System (INIS)

Breunlin, Jonas

2011-03-01

The demands on the electron beam qualities for free-electron lasers (FEL) are challenging in terms of high peak currents. At FLASH, the high-gain FEL in Hamburg, longitudinal bunch compression is performed to achieve the requested high charge densities in short bunches. The precise control of the bunch compression process requires advanced diagnostics on the longitudinal bunch profile. The bunch length monitor presented in this thesis is based on a non-destructive detection using the electro-optic effect. The focus is on a compact and reliable system for permanent bunch diagnostics. The monitor provides single-shot measurements of the longitudinal bunch profiles with lengths of a few picoseconds by spectrally encoding their charge distribution. First measurements for characterization purpose have been performed. It has been shown that the monitor is suitable for monitoring the longitudinal bunch profile behind the first bunch compressor at FLASH. Electron bunch profiles with slopes corresponding to a full width half maximum of about 1.4 ps have been detected. That is the intrinsic resolution limit of the utilized method. (orig.)

Urethroplasty for treatment of long anterior urethral stricture: buccal mucosa graft versus penile skin graft-does the stricture length matter?

Science.gov (United States)

Hussein, Mohamed M; Almogazy, Hazem; Mamdouh, Ahmed; Farag, Fawzy; Rashed, Elnesr; Gamal, Wael; Rashed, Ahmed; Zaki, Mohamed; Salem, Esam; Ryad, Ahmed

2016-11-01

To investigate the surgical outcomes of dorsal onlay urethroplasty (DOU) using buccal mucosa graft (BMG) or penile skin graft (PSG) and to assess the effect of stricture length in men with anterior urethral strictures. A prospective cohort included men with anterior urethral strictures between 2008 and 2015. Patients underwent DOU using PSG or BMG. Patients had urethrography and uroflowmetry at 0, 3, 6, 12 months, and urethroscopy when needed. Student's t test, Mann-Whitney U tests, and Pearson's Chi-square test were used for analysis. Sixty-nine patients (43 ± 14 year) were included, 31 received BMG, and 38 received PSG. Mean stricture length was 8 ± 3 cm, mean operative time was 145 ± 31 min, and mean follow-up was 56 ± 10 mo. Success rate was 87 % (90 % BMG vs. 84 % PSG, p = 0.4). Mean operative time was significantly shorter in PSG group (136 ± 29 min vs. 256 ± 58 min, p = 0.0005). Complications of grade I developed in 36 % (wound infection = 10 %, postvoiding dribbling = 18.8 %). Thirty of 69 patients (43 %) had strictures ≥8 cm, and 39 (57 %) had strictures <8 cm-success rate was equal for both subgroups (87 %). Mean blood loss, mean operative time, and incidence of postvoid dribbling were significantly lower in strictures <8 cm. BMG and PSG have comparable success rates in treatment of long anterior urethral strictures. Operative time is significantly longer in BMG. Long-segment strictures are associated with longer operative time, more blood loss, and more occurrence of postvoid dribbling. However, the length of the stricture has no influence on the success rate and functional outcomes of DOU.

Error Analysis of CM Data Products Sources of Uncertainty

Energy Technology Data Exchange (ETDEWEB)

Hunt, Brian D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Eckert-Gallup, Aubrey Celia [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Cochran, Lainy Dromgoole [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Kraus, Terrence D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Allen, Mark B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Beal, Bill [National Security Technologies, Joint Base Andrews, MD (United States); Okada, Colin [National Security Technologies, LLC. (NSTec), Las Vegas, NV (United States); Simpson, Mathew [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-02-01

This goal of this project is to address the current inability to assess the overall error and uncertainty of data products developed and distributed by DOE’s Consequence Management (CM) Program. This is a widely recognized shortfall, the resolution of which would provide a great deal of value and defensibility to the analysis results, data products, and the decision making process that follows this work. A global approach to this problem is necessary because multiple sources of error and uncertainty contribute to the ultimate production of CM data products. Therefore, this project will require collaboration with subject matter experts across a wide range of FRMAC skill sets in order to quantify the types of uncertainty that each area of the CM process might contain and to understand how variations in these uncertainty sources contribute to the aggregated uncertainty present in CM data products. The ultimate goal of this project is to quantify the confidence level of CM products to ensure that appropriate public and worker protections decisions are supported by defensible analysis.

Construction of a full-length prototype of the BESIII drift chamber and on-detector test for the BESIII drift chamber electronics

International Nuclear Information System (INIS)

Qin Zhonghua; Wu Linghui; Liu Jianbei; Chinese Academy of Sciences, Beijing; Yan Zhikang; Hunan Univ., Changsha; Chen Yuanbo; Chen Chang; Xu Meihang; Wang Lan; Ma Xiaoyan; Jin Yan; Liu Rongguang; Tang Xiao; Zhang Guifang; Zhu Qiming; Sheng Huayi; Zhu Kejun

2007-01-01

A full-length prototype of the BESIII drift chamber was built. The experience gained on gas sealing, high voltage supply and front-end electronics installation should be greatly beneficial to the successful construction of the BESIII drift chamber. An on-detector test of the BESIII drift chamber electronics was carried out with the constructed prototype chamber. The noise performance, drift time and charge measurements, and electronics gains were examined specifically. The final test results indicate that the electronics have a good performance and can satisfy their design requirements. (authors)

LPI Thresholds in Longer Scale Length Plasmas Driven by the Nike Laser*

Science.gov (United States)

Weaver, J.; Oh, J.; Phillips, L.; Afeyan, B.; Seely, J.; Kehne, D.; Brown, C.; Obenschain, S.; Serlin, V.; Schmitt, A. J.; Feldman, U.; Holland, G.; Lehmberg, R. H.; McLean, E.; Manka, C.

2010-11-01

The Krypton-Fluoride (KrF) laser is an attractive driver for inertial confinement fusion due to its short wavelength (248nm), large bandwidth (1-3 THz), and beam smoothing by induced spatial incoherence. Experiments with the Nike KrF laser have demonstrated intensity thresholds for laser plasma instabilities (LPI) higher than reported for other high power lasers operating at longer wavelengths (>=351 nm). The previous Nike experiments used short pulses (350 ps FWHM) and small spots (<260 μm FWHM) that created short density scale length plasmas (Ln˜50-70 μm) from planar CH targets and demonstrated the onset of two-plasmon decay (2φp) at laser intensities ˜2x10^15 W/cm^2. This talk will present an overview of the current campaign that uses longer pulses (0.5-4.0 ns) to achieve greater density scale lengths (Ln˜100-200 μm). X-rays, emission near ^1/2φo and ^3/2φo harmonics, and reflected laser light have been monitored for onset of 2φp. The longer density scale lengths will allow better comparison to results from other laser facilities. *Work supported by DoE/NNSA and ONR.

Collective dynamics of glass-forming polymers at intermediate length scales

International Nuclear Information System (INIS)

Colmenero, J.; Alvarez, F.; Arbe, A.

2015-01-01

Deep understanding of the complex dynamics taking place in glass-forming systems could potentially be gained by exploiting the information provided by the collective response monitored by coherent neutron scattering. We have revisited the question of the characterization of the collective response of polyisobutylene at intermediate length scales observed by neutron spin echo (NSE) experiments. The model, generalized for sub-linear diffusion - as it is the case of glass-forming polymers - has been successfully applied by using the information on the total self-motions available from MD-simulations properly validated by direct comparison with experimental results. From the fits of the coherent NSE data, the collective time at Q → 0 has been extracted that agrees very well with compiled results from different experimental techniques directly accessing such relaxation time. We show that a unique temperature dependence governs both, the Q → 0 and Q → ∞ asymptotic characteristic times. The generalized model also gives account for the modulation of the apparent activation energy of the collective times with the static structure factor. It mainly results from changes of the short-range order at inter-molecular length scales

Telomere Length and Mortality

DEFF Research Database (Denmark)

Kimura, Masayuki; Hjelmborg, Jacob V B; Gardner, Jeffrey P

2008-01-01

Leukocyte telomere length, representing the mean length of all telomeres in leukocytes, is ostensibly a bioindicator of human aging. The authors hypothesized that shorter telomeres might forecast imminent mortality in elderly people better than leukocyte telomere length. They performed mortality...

Two-dimensional photonic crystal bandedge laser with hybrid perovskite thin film for optical gain

Energy Technology Data Exchange (ETDEWEB)

Cha, Hyungrae [Department of Biophysics and Chemical Biology, Seoul National University, Seoul 08826 (Korea, Republic of); Inter-University Semiconductor Research Center, Seoul National University, Seoul 08826 (Korea, Republic of); Bae, Seunghwan [Department of Materials Science and Engineering, Seoul National University, Seoul 08826 (Korea, Republic of); Lee, Myungjae [Inter-University Semiconductor Research Center, Seoul National University, Seoul 08826 (Korea, Republic of); Department of Physics and Astronomy, Seoul National University, Seoul 08826 (Korea, Republic of); Jeon, Heonsu, E-mail: hsjeon@snu.ac.kr [Department of Biophysics and Chemical Biology, Seoul National University, Seoul 08826 (Korea, Republic of); Inter-University Semiconductor Research Center, Seoul National University, Seoul 08826 (Korea, Republic of); Department of Physics and Astronomy, Seoul National University, Seoul 08826 (Korea, Republic of)

2016-05-02

We report optically pumped room temperature single mode laser that contains a thin film of hybrid perovskite, an emerging photonic material, as gain medium. Two-dimensional square lattice photonic crystal (PhC) backbone structure enables single mode laser operation via a photonic bandedge mode, while a thin film of methyl-ammonium lead iodide (CH{sub 3}NH{sub 3}PbI{sub 3}) spin-coated atop provides optical gain for lasing. Two kinds of bandedge modes, Γ and M, are employed, and both devices laser in single mode at similar laser thresholds of ∼200 μJ/cm{sup 2} in pulse energy density. Polarization dependence measurements reveal a clear difference between the two kinds of bandedge lasers: isotropic for the Γ-point laser and highly anisotropic for the M-point laser. These observations are consistent with expected modal properties, confirming that the lasing actions indeed originate from the corresponding PhC bandedge modes.

Photonic crystal fibers for supercontinuum generation pumped by a gain-switched CW fiber laser

DEFF Research Database (Denmark)

Larsen, Casper; Noordegraaf, Danny; Hansen, Kim P.

2012-01-01

Supercontinuum generation in photonics crystal fibers (PCFs) pumped by CW lasers yields high spectral power density and average power. However, such systems require very high pump power and long nonlinear fibers. By on/off modulating the pump diodes of the fiber laser, the relaxation oscillations...... of the laser can be exploited to enhance the broadening process. The physics behind the supercontinuum generation is investigated by sweeping the fiber length, the zero dispersion wavelength, and the fiber nonlinearity. We show that by applying gain-switching a high average output power of up to 30 W can...

Application of radiation degraded CM-chitosan for preservation of fresh fruits

International Nuclear Information System (INIS)

Quynh, Tran Minh; Hien, Nuguyen Quoc; Yoshii, Fumio; Nagasawa, Naotsugu; Kume, Tamikazu

2003-01-01

CM-chitosan was irradiated with various doses in powder state and solution using Co 60 gamma source. The changes of viscosity in solution as well as molecular weight were also measured. The molecular weight reduced with increasing of radiation dose. The antimicrobial activity of CM-chitosan and irradiated CM-chitosan in solution against E.coli was investigated. In this studies, the sensitivity of E.coli depended on the concentration of CM-chitosan supplemented into medium and the antimicrobial activity of irradiated CM-chitosan was found to increase with radiation dose and reached to maximum with dose of 100 kGy. The 2% aqueous solutions prepared from CM-chitosan and 100 kGy irradiated CM-chitosan as mentioned above were applied for apple preservation. All coating fruits have significantly reduced the weight loss, spoilage ratio compared with control. Chemical and sensory quality of coated fruits were evaluated and compared, the best results were achieved with fruit coated using irradiated CM-chitosan. (author)

Numerical analysis of the optimal length and profile of a linearly chirped fiber Bragg grating for dispersion compensation.

Science.gov (United States)

Thibault, S; Lauzon, J; Cliche, J F; Martin, J; Duguay, M A; Têtu, M

1995-03-15

We propose a theoretical investigation of the length and coupling profile of a linearly chirped fiber Bragg grating for maximum dispersion compensation in a repeaterless optical communication system. The system consists of 100 km of standard optical fiber in which a 1550-nm signal, directly modulated at 2.5 Gbits/s, is launched. We discuss the results obtained with 6-, 4.33-, and 1-cm-long linearly chirped fiber Bragg gratings having Gaussian and uniform coupling profiles. We numerically show that a 4.33-cm-long chirped fiber Bragg grating having a uniform coupling profile is capable of compensating efficiently for the dispersion of our optical communication system.

CO2-laser ablation of Bi-Sr-Ca-Cu oxide by millisecond pulse lengths

Science.gov (United States)

Meskoob, M.; Honda, T.; Safari, A.; Wachtman, J. B.; Danforth, S.; Wilkens, B. J.

1990-03-01

We have achieved ablation of Bi-Sr-Ca-Cu oxide from single targets of superconducting pellets by CO2-laser pulses of l ms length to grow superconducting thin films. Upon annealing, the 6000-Å thin films have a Tc (onset) of 90 K and zero resistance at 78 K. X-ray diffraction patterns indicate the growth of single-phase thin films. This technique allows growth of uniform single-phase superconducting thin films of lateral area greater than 1 cm2.

Leading Gainful Employment Metric Reporting

Science.gov (United States)

Powers, Kristina; MacPherson, Derek

2016-01-01

This chapter will address the importance of intercampus involvement in reporting of gainful employment student-level data that will be used in the calculation of gainful employment metrics by the U.S. Department of Education. The authors will discuss why building relationships within the institution is critical for effective gainful employment…

Gain flattened L-band EDFA based on upgraded C-band EDFA using forward ASE pumping in an EDF section

DEFF Research Database (Denmark)

Buxens Azcoaga, Alvaro Juan; Poulsen, Henrik Nørskov; Clausen, Anders

2000-01-01

A novel method is presented for implementing an L-band erbium doped fibre amplifier (EDFA) making use of forward amplified spontaneous emission pumping, from a commercially available c-band EDFA, in an erbium doped fibre. Tuning of the length of erbium doped fibre enables a flat gain characteristic...... to be obtained with a low noise figure over the entire L-band window....

Can Beta Blockers Cause Weight Gain?

Science.gov (United States)

... cause weight gain? Can beta blockers cause weight gain? Answers from Sheldon G. Sheps, M.D. Yes. Weight gain can occur as a side effect of some ... and metoprolol (Lopressor, Toprol-XL). The average weight gain is about 2.6 pounds (about 1.2 ...

Micro-computed Tomographic Analysis of Apical Microcracks before and after Root Canal Preparation by Hand, Rotary, and Reciprocating Instruments at Different Working Lengths.

Science.gov (United States)

de Oliveira, Bruna Paloma; Câmara, Andréa Cruz; Duarte, Daniel Amancio; Heck, Richard John; Antonino, Antonio Celso Dantas; Aguiar, Carlos Menezes

2017-07-01

This study aimed to compare apical microcrack formation after root canal shaping by hand, rotary, and reciprocating files at different working lengths using micro-computed tomographic analysis. Sixty mandibular incisors were randomly divided into 6 experimental groups (n = 10) according to the systems and working lengths used for the root canal preparation: ProTaper Universal for Hand Use (Dentsply Maillefer, Ballaigues, Switzerland), HyFlex CM (Coltene-Whaledent, Allstetten, Switzerland), and Reciproc (VDW, Munich, Germany) files working at the apical foramen (AF) and 1 mm short of the AF (AF - 1 mm). The teeth were imaged with micro-computed tomographic scanning at an isotropic resolution of 14 μm before and after root canal preparation, and the cross-sectional images generated were assessed to detect microcracks in the apical portion of the roots. Overall, 17 (28.3%) specimens presented microcracks before instrumentation. Apical microcracks were present in 1 (ProTaper Universal for Hand Use), 3 (Hyflex CM), and 2 (Reciproc) specimens when the instrumentation terminated at the AF. When instrumentation was terminated at AF - 1 mm, apical microcracks were detected in 3 (ProTaper Universal for Hand Use) and 4 (Hyflex CM and Reciproc) specimens. All these microcracks detected after root canal preparation were already present before instrumentation, and no new apical microcrack was visualized. For all groups, the number of slices presenting microcracks after root canal preparation was the same as before canal preparation. Root canal shaping with ProTaper Universal for Hand Use, HyFlex CM, and Reciproc systems, regardless of the working length, did not produce apical microcracks. Copyright © 2017 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

Physics at 1034 cm-2 s-1

International Nuclear Information System (INIS)

Diebold, R.; Wagner, R.

1984-01-01

Most of the detector studies at Snowmass-84 have rightfully concentrated on detailed studies of individual interactions - their rates, signatures, and backgrounds. Depending on the physics and the detector components, there seems to be agreement that general-purpose detectors will likely be able to accept luminosities up to 10 32-33 cm -2 s -1 . The purpose of this paper is to show how the physics reach of the SSC is extended by going to a luminosity of 10 34 cm -2 s -1 , to take a first look at what sort of detector could be used at this luminosity, and to discuss how one might trigger on interesting events in the presence of many overlapping minimum bias events. We will assume that the SSC turns on at 10 31 or 10 32 cm -2 s -1 , with an increase of luminosity to 10 33 over a period of a few years as the machine and detectors become better understood. Thus, the lower mass scale will have been explored and we can set our thresholds high when running 10 34

Estimating the potential gains from mergers

DEFF Research Database (Denmark)

Bogetoft, Peter; Wang, Dexiang

2005-01-01

We introduce simple production economic models to estimate the potential gains from mergers. We decompose the gains into technical ef¿ciency, size (scale) and harmony (mix) gains, and we discuss alternative ways to capture these gains. We propose to approximate the production processes using...... the non-parametric. Data Envelopment Analysis (DEA) approach, and we use the resulting operational approach to estimate the potential gains from merging agricultural extension of¿ces in Denmark....

Laser scattering in large-scale-length plasmas relevant to National Ignition Facility hohlraums

International Nuclear Information System (INIS)

MacGowan, B.J.; Berger, R.L.; Afeyan, B.B.

1996-10-01

We have used homogeneous plasmas of high density (up to 1.3 X 10 21 electrons per cm 3 ) and temperature (∼ 3 keV) with large density scale lengths (∼2 mm) to approximate conditions within National Ignition Facility (NIF) hohlraums. Within these plasmas we have studied the dependence of stimulated Raman (SRS) and Brillouin (SBS) scattering on beam smoothing and plasma conditions at the relevant laser intensity (3ω, 2 X 10 15 Wcm 2 ). Both SBS and SRS are reduced by the use of smoothing by spectral dispersion (SSD)

Genetic parameters and trends of morphometric traits of GIFT tilapia under selection for weight gain

Directory of Open Access Journals (Sweden)

Rafael Vilhena Reis Neto

2014-08-01

Full Text Available The main factor considered in breeding programs for fish is growth, which can be assessed in terms of a gain in either weight or body measurements. This study was undertaken to evaluate the morphometric traits of GIFT strain tilapia (Oreochromis sp. selected for weight gain. The data set used contained information on 6,650 animals. The genetic values of 8,590 animals in a relationship matrix of five generations were predicted. The following morphometric measurements were evaluated: standard length; body depth and body width. Body area and volume were also calculated. Bi-character analyses involving morphometric traits were used to estimate (covariance components. Heritability, larval and fingerling common environmental effects were estimated for each trait, together with the genetic and phenotypic correlations between traits. Bayesian procedures were utilised by Gibbs chains, and the convergence of the chains was tested using the Heidelberger and Welch method. Genetic trends were estimated by segmented regression of the fish breeding values of the generations considered in this study. Estimates of heritability (0.28 a 0.31 had moderate to high magnitudes for all traits. Genetic correlations between traits were all above 0.8, and the genetic gains were satisfactory from the third generation onwards. From the estimates of the genetic parameters and genetic gain the morphometric traits evaluated have good potential for selection.

High-Performance 1.55-µm Superluminescent Diode Based on Broad Gain InAs/InGaAlAs/InP Quantum Dash Active Region

KAUST Repository

Khan, Mohammed Zahed Mustafa; Ng, Tien Khee; Ooi, Boon S.

2014-01-01

of 140 nm, with a peak modal gain of ~41 cm-1. The noncoated two-section gainabsorber broad-area and ridge-waveguide device configuration exhibits an output power of > 20 mW and > 12 mW, respectively. The corresponding -3-dB bandwidths span ~82 nm and ~72

Eruption of first permanent incisors and live weight gain in grazing yearling Angora goats.

Science.gov (United States)

McGregor, B A; Butler, K L

2013-05-01

To investigate the effects of the timing and duration of eruption of the first permanent incisors, live weight, sex and other factors on contemporaneous live weight gain in Angora goats. Goats were previously part of a pen study on the effects of energy intake of Angora does during pregnancy and lactation on kid development. The design was 3 levels of nutrition in mid-pregnancy by 2 levels of postnatal nutrition in 17 randomised blocks. Artificial insemination, ultrasound examination and feeding does in pens enabled accurate conduct of the study. After weaning, goats were grazed in sex groups. Live weight change between 14 and 20 months of age was related to deciduous first incisor loss and permanent first incisor development and other attributes assessed before the study. Live weight change was related to the elapsed time for first permanent incisors to commence eruption and to the length of time for first permanent incisors to erupt. This response was affected by sex. Over summer and autumn, entire males with short eruption intervals gained 2-3 kg more than entire males with long eruption intervals. Females that reached first permanent incisor eruption by mid-summer had a live weight gain of 3 kg more than those that reached the same development 3 months later. Live weight change in yearling Angora goats was associated with the process of first permanent incisor eruption. In females, live weight gain was greater when first permanent incisor eruption was earlier. In males, live weight gain was greater when first permanent incisor eruption was faster. © 2013 The Authors. Australian Veterinary Journal © 2013 Australian Veterinary Association.

A leaf sequencing algorithm to enlarge treatment field length in IMRT

International Nuclear Information System (INIS)

Xia Ping; Hwang, Andrew B.; Verhey, Lynn J.

2002-01-01

With MLC-based IMRT, the maximum usable field size is often smaller than the maximum field size for conventional treatments. This is due to the constraints of the overtravel distances of MLC leaves and/or jaws. Using a new leaf sequencing algorithm, the usable IMRT field length (perpendicular to the MLC motion) can be mostly made equal to the full length of the MLC field without violating the upper jaw overtravel limit. For any given intensity pattern, a criterion was proposed to assess whether an intensity pattern can be delivered without violation of the jaw position constraints. If the criterion is met, the new algorithm will consider the jaw position constraints during the segmentation for the step and shoot delivery method. The strategy employed by the algorithm is to connect the intensity elements outside the jaw overtravel limits with those inside the jaw overtravel limits. Several methods were used to establish these connections during segmentation by modifying a previously published algorithm (areal algorithm), including changing the intensity level, alternating the leaf-sequencing direction, or limiting the segment field size. The algorithm was tested with 1000 random intensity patterns with dimensions of 21x27 cm2, 800 intensity patterns with higher intensity outside the jaw overtravel limit, and three different types of clinical treatment plans that were undeliverable using a segmentation method from a commercial treatment planning system. The new algorithm achieved a success rate of 100% with these test patterns. For the 1000 random patterns, the new algorithm yields a similar average number of segments of 36.9±2.9 in comparison to 36.6±1.3 when using the areal algorithm. For the 800 patterns with higher intensities outside the jaw overtravel limits, the new algorithm results in an increase of 25% in the average number of segments compared to the areal algorithm. However, the areal algorithm fails to create deliverable segments for 90% of these

Postnatal Growth Patterns in a Chilean Cohort: The Role of SES and Family Environment

Science.gov (United States)

Kang Sim, D. E.; Cappiello, M.; Castillo, M.; Lozoff, B.; Martinez, S.; Blanco, E.; Gahagan, S.

2012-01-01

Objective. This study examined how family environmental characteristics served as mediators in the relationship between socioeconomic conditions and infant growth in a cohort of Chilean infants. Methods. We studied 999 infants, born between 1991 and 1996, from a longitudinal cohort which began as an iron deficiency anemia preventive trial. SES (Graffar Index), the Life Experiences Survey, and the Home Observation for Measurement of the Environment (HOME) were assessed in infancy. Using path analysis, we assessed the relationships between the social factors, home environment, and infant growth. Results. During the first year, weight and length gain averaged 540 grams/month and 6.5 cm/month, respectively. In the path analysis model for weight gain, higher SES and a better physical environment were positively related to higher maternal warmth, which in turn was associated with higher average weight gain. Higher SES was directly related to higher average length gain. Conclusions. In our cohort, a direct relationship between SES and length gain developed during infancy. Higher SES was indirectly related to infant weight gain through the home environment and maternal warmth. As the fastest growing infants are at risk for later obesity, new strategies are needed to encourage optimal rather than maximal growth. PMID:22666275

Postnatal Growth Patterns in a Chilean Cohort: The Role of SES and Family Environment

Directory of Open Access Journals (Sweden)

D. E. Kang Sim

2012-01-01

Full Text Available Objective. This study examined how family environmental characteristics served as mediators in the relationship between socioeconomic conditions and infant growth in a cohort of Chilean infants. Methods. We studied 999 infants, born between 1991 and 1996, from a longitudinal cohort which began as an iron deficiency anemia preventive trial. SES (Graffar Index, the Life Experiences Survey, and the Home Observation for Measurement of the Environment (HOME were assessed in infancy. Using path analysis, we assessed the relationships between the social factors, home environment, and infant growth. Results. During the first year, weight and length gain averaged 540 grams/month and 6.5 cm/month, respectively. In the path analysis model for weight gain, higher SES and a better physical environment were positively related to higher maternal warmth, which in turn was associated with higher average weight gain. Higher SES was directly related to higher average length gain. Conclusions. In our cohort, a direct relationship between SES and length gain developed during infancy. Higher SES was indirectly related to infant weight gain through the home environment and maternal warmth. As the fastest growing infants are at risk for later obesity, new strategies are needed to encourage optimal rather than maximal growth.

Full-length Ebola glycoprotein accumulates in the endoplasmic reticulum

Directory of Open Access Journals (Sweden)

Bhattacharyya Suchita

2011-01-01

Full Text Available Abstract The Filoviridae family comprises of Ebola and Marburg viruses, which are known to cause lethal hemorrhagic fever. However, there is no effective anti-viral therapy or licensed vaccines currently available for these human pathogens. The envelope glycoprotein (GP of Ebola virus, which mediates entry into target cells, is cytotoxic and this effect maps to a highly glycosylated mucin-like region in the surface subunit of GP (GP1. However, the mechanism underlying this cytotoxic property of GP is unknown. To gain insight into the basis of this GP-induced cytotoxicity, HEK293T cells were transiently transfected with full-length and mucin-deleted (Δmucin Ebola GP plasmids and GP localization was examined relative to the nucleus, endoplasmic reticulum (ER, Golgi, early and late endosomes using deconvolution fluorescent microscopy. Full-length Ebola GP was observed to accumulate in the ER. In contrast, GPΔmucin was uniformly expressed throughout the cell and did not localize in the ER. The Ebola major matrix protein VP40 was also co-expressed with GP to investigate its influence on GP localization. GP and VP40 co-expression did not alter GP localization to the ER. Also, when VP40 was co-expressed with the nucleoprotein (NP, it localized to the plasma membrane while NP accumulated in distinct cytoplasmic structures lined with vimentin. These latter structures are consistent with aggresomes and may serve as assembly sites for filoviral nucleocapsids. Collectively, these data suggest that full-length GP, but not GPΔmucin, accumulates in the ER in close proximity to the nuclear membrane, which may underscore its cytotoxic property.

Length of Barrett's segment predicts failure of eradication in radiofrequency ablation for Barrett's esophagus: a retrospective cohort study.

Science.gov (United States)

Luckett, Tyler; Allamneni, Chaitanya; Cowley, Kevin; Eick, John; Gullick, Allison; Peter, Shajan

2018-05-21

We aim to investigate factors that may contribute to failure of eradication of dysplastic Barrett's Esophagus among patients undergoing radiofrequency ablation treatment. A retrospective review of patients undergoing radiofrequency ablation for treatment of Barrett's Esophagus was performed. Data analyzed included patient demographics, medical history, length of Barrett's Esophagus, number of radiofrequency ablation sessions, and histopathology. Subsets of patients achieving complete eradication were compared with those not achieving complete eradication. A total of 107 patients underwent radiofrequency ablation for Barrett's Esophagus, the majority white, overweight, and male. Before treatment, 63 patients had low-grade dysplasia, and 44 patients had high-grade dysplasia or carcinoma. Complete eradication was achieved in a majority of patients (57% for metaplasia, and 76.6% for dysplasia). Failure of eradication occurred in 15.7% of patients. The median number of radiofrequency ablation treatments in patients achieving complete eradication was 3 sessions, compared to 4 sessions for failure of eradication (p = 0.06). Barrett's esophagus length of more than 5 cm was predictive of failure of eradication (p Radiofrequency ablation for dysplastic Barrett's Esophagus is a proven and effective treatment modality, associated with a high rate of complete eradication. Our rates of eradication from a center starting an ablation program are comparable to previously published studies. Length of Barrett's segment > 5 cm was found to be predictive of failure of eradication in patients undergoing radiofrequency ablation.

Does length or neighborhood size cause the word length effect?

Science.gov (United States)

Jalbert, Annie; Neath, Ian; Surprenant, Aimée M

2011-10-01

Jalbert, Neath, Bireta, and Surprenant (2011) suggested that past demonstrations of the word length effect, the finding that words with fewer syllables are recalled better than words with more syllables, included a confound: The short words had more orthographic neighbors than the long words. The experiments reported here test two predictions that would follow if neighborhood size is a more important factor than word length. In Experiment 1, we found that concurrent articulation removed the effect of neighborhood size, just as it removes the effect of word length. Experiment 2 demonstrated that this pattern is also found with nonwords. For Experiment 3, we factorially manipulated length and neighborhood size, and found only effects of the latter. These results are problematic for any theory of memory that includes decay offset by rehearsal, but they are consistent with accounts that include a redintegrative stage that is susceptible to disruption by noise. The results also confirm the importance of lexical and linguistic factors on memory tasks thought to tap short-term memory.

Correlated evolution of sternal keel length and ilium length in birds

Directory of Open Access Journals (Sweden)

Tao Zhao

2017-07-01

Full Text Available The interplay between the pectoral module (the pectoral girdle and limbs and the pelvic module (the pelvic girdle and limbs plays a key role in shaping avian evolution, but prior empirical studies on trait covariation between the two modules are limited. Here we empirically test whether (size-corrected sternal keel length and ilium length are correlated during avian evolution using phylogenetic comparative methods. Our analyses on extant birds and Mesozoic birds both recover a significantly positive correlation. The results provide new evidence regarding the integration between the pelvic and pectoral modules. The correlated evolution of sternal keel length and ilium length may serve as a mechanism to cope with the effect on performance caused by a tradeoff in muscle mass between the pectoral and pelvic modules, via changing moment arms of muscles that function in flight and in terrestrial locomotion.

A Coherent Compton Backscattering High Gain FEL using an X-Band Microwave Undulator

CERN Document Server

Pellegrini, C; Travish, G

2005-01-01

We describe a proposed high-gain FEL using an X-band microwave undulator and operating at a wavelength of about 0.5 μm. The FEL electron beam energy is 65 MeV. The beam is produced by the NLCTA X-band linac at SLAC, using an S-band high-brightness photoinjector. The undulator consists of a circular waveguide with an rf wave counter-propagating with respect to the electron beam. The undulator is powered with two high-power X-band klystrons and a dual-moded pulse compressor recently developed at SLAC. This system is capable of delivering flat-top rf pulses of up to 400 ns and a few hundred megawatts. The equivalent undulator period is 1.4 cm, the radius of the circular pipe is 1 cm, and the undulator parameter is about 0.4 for a helical undulator configuration, obtained using two cross-polarized TE modes, or larger for a planar configuration, using one rf polarization. The undulator is about four meters long. The FEL will reach saturation within this distance when operated in a SASE mode. We describe t...

Weight gain in pregnancy and application of the 2009 IOM guidelines: toward a uniform approach.

Science.gov (United States)

Gilmore, L Anne; Redman, Leanne M

2015-03-01

There is an urgent need to adopt standardized nomenclature as it relates to gestational weight gain (GWG), a more uniform approach to calculate it, and hence quantifying adherence to the 2009 Institute of Medicine (IOM) guidelines. This perspective highlights the varying methods used to estimate GWG and discuss the advantages and limitations of each. While these calculations could be argued to have a minimal impact on data at the population level, on the patient level, incorrectly estimating weight at conception can result in misclassification of preconception body mass index (BMI) and assignment of the IOM guidelines which inherently affect the prospective management of weight gain (and potential outcomes) during the current pregnancy. This study recommends that preconception BMI and total GWG be determined objectively and total GWG be adjusted for length of gestation before assessing adherence to the IOM GWG guidelines. © 2014 The Obesity Society.

Investigation of the required length for fully developed pipe flow with drag-reducing polymer solutions

Science.gov (United States)

Farsiani, Yasaman; Elbing, Brian

2015-11-01

Adding trace amounts of long chain polymers into a liquid flow is known to reduce skin friction drag by up to 80%. While polymer drag reduction (PDR) has been successfully implemented in internal flows, diffusion and degradation have limited its external flow applications. A weakness in many previous PDR studies is that there was no characterization of the polymer being injected into the turbulent boundary layer, which can be accomplished by testing a sample in a pressure-drop tube. An implicit assumption in polymer characterization is that the flow is fully developed at the differential pressure measurement. While available data in the literature shows that the entry length to achieve fully developed flow increases with polymeric solutions, it is unclear how long is required to achieve fully developed flow for non-Newtonian turbulent flows. In the present study, the pressure-drop is measured across a 1.05 meter length section of a 1.04 cm inner diameter pipe. Differential pressure is measured with a pressure transducer for different entry lengths, flow and polymer solution properties. This presentation will present preliminary data on the required entrance length as well as characterization of polymer solution an estimate of the mean molecular weight.

A gain-coefficient switched Alexandrite laser

International Nuclear Information System (INIS)

Lee, Chris J; Van der Slot, Peter J M; Boller, Klaus-J

2013-01-01

We report on a gain-coefficient switched Alexandrite laser. An electro-optic modulator is used to switch between high and low gain states by making use of the polarization dependent gain of Alexandrite. In gain-coefficient switched mode, the laser produces 85 ns pulses with a pulse energy of 240 mJ at a repetition rate of 5 Hz.

Electron beam bunch length characterizations using incoherent and coherent transition radiation on the APS SASE FEL project

CERN Document Server

Lumpkin, Alex H; Berg, W J; Lewellen, J W; Sereno, N S; Happek, U

2000-01-01

The Advanced Photon Source (APS) injector linac has been reconfigured with a low-emittance RF thermionic gun and a photocathode (PC) RF gun to support self-amplified spontaneous emission (SASE) free-electron laser (FEL) experiments. One of the most critical parameters for optimizing SASE performance (gain length) is the electron beam peak current, which requires a charge measurement and a bunch length measurement capability. We report here initial measurements of the latter using both incoherent optical transition radiation (OTR) and coherent transition radiation (CTR). A visible light Hamamatsu C5680 synchroscan streak camera was used to measure the thermionic RF gun beam's bunch length (sigma approx 2-3 ps) via OTR generated by the beam at 220 MeV and 200 mA macropulse average current. In addition, a CTR monitor (Michelson Interferometer) based on a Golay cell as the far-infrared (FIR) detector has been installed at the 40-MeV station in the beamline. Initial observations of CTR signal strength variation wi...

CM 40907: a structurally novel anticonvulsant in mice, rats and baboons

International Nuclear Information System (INIS)

Chambon, J.P.; Brochard, J.; Hallot, A.; Heaulme, M.; Brodin, R.; Roncucci, R.; Biziere, K.

1985-01-01

CM 40907 [3-(4-hydroxypiperidyl)-6-(2'-chlorophenyl)-pyridazine] is a chemically original compound which possesses the pharmacological properties of a potent, p.o. active anticonvulsant. The anticonvulsant activity of CM 40907 was examined in mice, rats and photosensitive Papio-papio baboons and compared to that of phenobarbital, diphenylhydantoin, carbamazepine, sodium valproate and ethosuximide. In mice, CM 40907 antagonized electroconvulsive shock and chemically induced seizures with an overall potency comparable to that of carbamazepine and a therapeutic ratio (ED50 rotorod/ED50 electroshock) superior to that of ethosuximide, sodium valproate, phenobarbital and carbamazepine. In the rat CM 40907 suppressed completed kindled amygdaloid seizures and was approximately as active as phenobarbital. In naturally photosensitive Senegalese Papio-papio baboons CM 40907 antagonized myoclonus and cortical paroxysmal discharges. In this model CM 40907 was approximately one-fourth as potent as phenobarbital, twice as potent as carbamazepine and 6 times more potent than sodium valproate. In mice CM 40907, at anticonvulsant doses, increased the affinity of [ 3 H]flunitrazepam for its central receptor site. Based on these results it is postulated that CM 40907 is a potent and relatively nonsedative anticonvulsant and may be of therapeutic benefit in epileptic disorders

Stimulus-dependent modulation of spike burst length in cat striate cortical cells.

Science.gov (United States)

DeBusk, B C; DeBruyn, E J; Snider, R K; Kabara, J F; Bonds, A B

1997-07-01

Burst activity, defined by groups of two or more spikes with intervals of cats. Bursting varied broadly across a population of 507 simple and complex cells. Half of this population had > or = 42% of their spikes contained in bursts. The fraction of spikes in bursts did not vary as a function of average firing rate and was stationary over time. Peaks in the interspike interval histograms were found at both 3-5 ms and 10-30 ms. In many cells the locations of these peaks were independent of firing rate, indicating a quantized control of firing behavior at two different time scales. The activity at the shorter time scale most likely results from intrinsic properties of the cell membrane, and that at the longer scale from recurrent network excitation. Burst frequency (bursts per s) and burst length (spikes per burst) both depended on firing rate. Burst frequency was essentially linear with firing rate, whereas burst length was a nonlinear function of firing rate and was also governed by stimulus orientation. At a given firing rate, burst length was greater for optimal orientations than for nonoptimal orientations. No organized orientation dependence was seen in bursts from lateral geniculate nucleus cells. Activation of cortical contrast gain control at low response amplitudes resulted in no burst length modulation, but burst shortening at optimal orientations was found in responses characterized by supersaturation. At a given firing rate, cortical burst length was shortened by microinjection of gamma-aminobutyric acid (GABA), and bursts became longer in the presence of N-methyl-bicuculline, a GABA(A) receptor blocker. These results are consistent with a model in which responses are reduced at nonoptimal orientations, at least in part, by burst shortening that is mediated by GABA. A similar mechanism contributes to response supersaturation at high contrasts via recruitment of inhibitory responses that are tuned to adjacent orientations. Burst length modulation can serve

Statistical 21-cm Signal Separation via Gaussian Process Regression Analysis

Science.gov (United States)

Mertens, F. G.; Ghosh, A.; Koopmans, L. V. E.

2018-05-01

Detecting and characterizing the Epoch of Reionization and Cosmic Dawn via the redshifted 21-cm hyperfine line of neutral hydrogen will revolutionize the study of the formation of the first stars, galaxies, black holes and intergalactic gas in the infant Universe. The wealth of information encoded in this signal is, however, buried under foregrounds that are many orders of magnitude brighter. These must be removed accurately and precisely in order to reveal the feeble 21-cm signal. This requires not only the modeling of the Galactic and extra-galactic emission, but also of the often stochastic residuals due to imperfect calibration of the data caused by ionospheric and instrumental distortions. To stochastically model these effects, we introduce a new method based on `Gaussian Process Regression' (GPR) which is able to statistically separate the 21-cm signal from most of the foregrounds and other contaminants. Using simulated LOFAR-EoR data that include strong instrumental mode-mixing, we show that this method is capable of recovering the 21-cm signal power spectrum across the entire range k = 0.07 - 0.3 {h cMpc^{-1}}. The GPR method is most optimal, having minimal and controllable impact on the 21-cm signal, when the foregrounds are correlated on frequency scales ≳ 3 MHz and the rms of the signal has σ21cm ≳ 0.1 σnoise. This signal separation improves the 21-cm power-spectrum sensitivity by a factor ≳ 3 compared to foreground avoidance strategies and enables the sensitivity of current and future 21-cm instruments such as the Square Kilometre Array to be fully exploited.

Stress calculations for RTNS-iI 50-cm targets

International Nuclear Information System (INIS)

Schumacher, B.J.; House, P.A.

1981-04-01

Structural calculations made during design of a 50-cm target for the Rotating Target Neutron Source (RTNS-II) are detailed. The limited ability of the current 23-cm diameter target to dissipate the additional beam power required for a yield increase from 2 x 10 13 to 4 x 10 13 neutrons/second has resulted in the need for a larger target. The stresses of several design configurations for a 50-cm target were calculated. The stress contours that would occur in several different target designs with and without various types of structural reinforcement that reduce stress and deflection are presented

CM-2 Environmental/Modal Testing of SPACEHAB Racks

Science.gov (United States)

McNelis, Mark E.; Goodnight, Thomas W.

2001-01-01

Combined environmental/modal vibration testing has been implemented at the NASA Glenn Research Center's Structural Dynamics Laboratory. The benefits of combined vibration testing are that it facilitates test article modal characterization and vibration qualification testing. The Combustion Module-2 (CM-2) is a space experiment that will launch on shuttle mission STS-107 in the SPACEHAB Research Double Module. The CM-2 flight hardware is integrated into a SPACEHAB single and double rack. CM-2 rack-level combined vibration testing was recently completed on a shaker table to characterize the structure's modal response and verify the random vibration response. Control accelerometers and limit force gauges, located between the fixture and rack interface, were used to verify the input excitation. Results of the testing were used to verify the loads and environments for flight on the shuttles.

First charge collection and position-precision data on the medium-resistivity silicon strip detectors before and after neutron irradiation up to 2x1014 n/cm2

International Nuclear Information System (INIS)

Li Zheng; Dezillie, B.; Eremin, V.; Li, C.J.; Verbitskaya, E.

1999-01-01

Test strip detectors of 125 μm, 500 μm, and 1 mm pitches with about 1 cm 2 areas have been made on medium-resistivity silicon wafers (1.3 and 2.7 kΩ cm). Detectors of 500 μm pitch have been tested for charge collection and position precision before and after neutron irradiation (up to 2x10 14 n/cm 2 ) using 820 and 1030 nm laser lights with different beam-spot sizes. It has been found that for a bias of 250 V a strip detector made of 1.3 kΩ cm (300 μm thick) can be fully depleted before and after an irradiation of 2x10 14 n/cm 2 . For a 500 μm pitch strip detector made of 2.7 kΩ cm tested with an 1030 nm laser light with 200 μm spot size, the position reconstruction error is about 14 μm before irradiation, and 17 μm after about 1.7x10 13 n/cm 2 irradiation. We demonstrated in this work that medium resistivity silicon strip detectors can work just as well as the traditional high-resistivity ones, but with higher radiation tolerance. We also tested charge sharing and position reconstruction using a 1030 nm wavelength (300 μm absorption length in Si at RT) laser, which provides a simulation of MIP particles in high-physics experiments in terms of charge collection and position reconstruction

The Effect of Commonly Performed Exercises on the Levator Hiatus Area and the Length and Strength of Pelvic Floor Muscles in Postpartum Women.

Science.gov (United States)

Siff, Lauren N; Hill, Audra J; Walters, Samantha J; Walters, Ginny; Walters, Mark D

2018-05-02

The aim oft his study was to compare the effects of 10 common exercises to traditional pelvic floor muscle (PFM) contractions (Kegel) on levator hiatus (LH) area and PFM length and strength. This is a cross-sectional study of 15 healthy postpartum women. Ten exercises were studied. These were common variations of leg, core, and back exercises used in yoga, Pilates, strength training, and physical therapy. Each participant performed all 10 exercises at a single visit in 2 examination settings: transperineal ultrasound and perineometry. Ultrasound measured the LH area and PFM length, and perineometry measured the muscle strength (peak squeeze pressure). Kegel generates an increase in squeeze pressure (24.3 cm H2O), shortens the muscles (-0.46 cm) and narrows the LH (-0.13 cm). The bird-dog and plank exercises were not different from Kegel in any measurement. While the leg-lift ultrasound dimensions are similar to Kegel, leg lifts generated peak squeeze pressures stronger than any other exercise (including Kegel). Whereas ultrasound dimensions were similar to Kegel, tucked and untucked squats and thigh adductions generated weaker contractions than Kegel. While crunch generated a squeeze pressure similar to Kegel, the ultrasound dimensions showed a significantly wider LH and longer muscle than Kegel. Bridge, clam, and plié exercises affected the PFMs differently than Kegel in all measures. Bird-dog, plank, and leg-lift exercises should be evaluated as alternative exercises to Kegel as they affect PFM strength and length and LH area similarly to Kegel, and leg lifts generate a stronger contraction than Kegel.

Electron heating, magnetic field amplification, and cosmic-ray precursor length at supernova remnant shocks

Energy Technology Data Exchange (ETDEWEB)

Laming, J. Martin [Space Science Division, Naval Research Laboratory, Code 7684, Washington, DC 20375 (United States); Hwang, Una [Department of Astronomy, University of Maryland, College Park, MD 20742 (United States); Ghavamian, Parviz [Department of Physics, Astronomy and Geosciences, Towson University, Towson, MD 21252 (United States); Rakowski, Cara, E-mail: laming@nrl.navy.mil, E-mail: Una.Hwang-1@nasa.gov, E-mail: pghavamian@towson.edu

2014-07-20

We investigate the observability, by direct and indirect means, of a shock precursor arising from magnetic field amplification by cosmic rays. We estimate the depth of such a precursor under conditions of nonresonant amplification, which can provide magnetic field strengths comparable to those inferred for supernova remnants. Magnetic field generation occurs as the streaming cosmic rays induce a plasma return current, and it may be quenched by either nonresonant or resonant channels. In the case of nonresonant saturation, the cosmic rays become magnetized and amplification saturates at higher magnetic fields. The precursor can extend out to 10{sup 17}-10{sup 18} cm and is potentially detectable. If resonant saturation occurs, the cosmic rays are scattered by turbulence and the precursor length will likely be much smaller. The dependence of precursor length on shock velocity has implications for electron heating. In the case of resonant saturation, this dependence is similar to that in the more familiar resonantly generated shock precursor, which when expressed in terms of the cosmic-ray diffusion coefficient kappav and shock velocity v{sub s} is kappav/v{sub s} . In the nonresonantly saturated case, the precursor length declines less quickly with increasing v{sub s} . Where precursor length proportional to 1/v{sub s} gives constant electron heating, this increased precursor length could be expected to lead to higher electron temperatures for nonresonant amplification. This should be expected at faster supernova remnant shocks than studied by previous works. Existing results and new data analysis of SN 1006 and Cas A suggest some observational support for this idea.

Association of newborn diseases with weight/length ratio and the adequacy of weight for gestational age

Directory of Open Access Journals (Sweden)

José Ricardo Dias Bertagnon

2011-09-01

Full Text Available Objective: To compare the frequencies of newborn diseases in thosenewborns classified according to a weight/length rate and thoseclassified by the adequacy weight for gestational age. Methods: Aretrospective cross-sectional study by record assessment was carriedout enclosing all the live newborns at Hospital Geral do Grajaú, fromSeptember to December, 2009 (n =577 classified according to therate weight/length and also to the adequacy weight for gestationalage. The 10 and 90 percentiles of the weight/length distribution, nowdesignated as “indices” were calculated leading to the followingclassification: low index, for newborns below 54.8 g/cm; high index,for those over 75.8 g/cm; and average index, for the remainingnewborns. According to the adequacy weight for gestational age thenewborns were designated as pre-term for gestational age; term smallfor gestational age; appropriate term and large term. In this samplethere were no small and large pre-term or post-term newborns. Majordiseases were related to the index and adequacy extracts by the χ2test for a contingency table. Results: A significant association wasfound among low index, pre-term for gestational age newborns andterm small for gestational age; between average index and appropriatefor gestational age term newborns; and high index with large termappropriate for gestational age newborns (p< 0.001. Hypoglycemia(3.4% was associated to both low and high indices, to appropriatefor gestational age preterm newborns and to small for gestational ageterm newborns. Sepsis (3.1% was associated to both low index andpre-term appropriate for gestational age newborns. The respiratorydistress syndrome (1.3% was associated to low index and pre-termappropriate for gestational age newborns. Other respiratory distresssyndromes (3.8% were associated to low and high indices but notto the adequacy for gestational age classification. Jaundice (14.9%was not associated to the studied classifications

The effect of length, duration, and intensity of psychological therapy on CORE global distress scores.

Science.gov (United States)

Evans, Lauren Jayne; Beck, Alison; Burdett, Mark

2017-09-01

This study explores whether improvements, as measured by the CORE-OM/10, as a result of psychological therapy were related to length of treatment in weeks, number of treatment sessions, or treatment intensity, as well as any effect of diagnostic group. Pre- and post-therapy CORE-OM/10 scores were extracted from the clinical records of all secondary care adult psychological therapy team patients who undertook psychological therapy between 2010 and 2013 in one mental health trust. Of the 4,877 patients identified, 925 had complete records. Length of therapy was divided by the number of sessions to create 'treatment intensity' (sessions per week). Nonparametric analyses were used, initial score was controlled for, and diagnostic group was explored. No relationship was found between change in score and the number of sessions, therapy length, or treatment intensity; however, change in score was positively correlated with first-session score. Patients with higher initial scores had longer therapies; however, treatment intensity was similar for patients with lower pre-therapy distress. There were differences in treatment length (weeks) between diagnostic groups. Demographic differences were found between patients with and without complete records, prompting caution in terms of generalizability. These findings are consistent with the responsive regulation model (Barkham et al., 1996) which proposes that patients vary in their response to treatment, resulting in no associations between session numbers or treatment intensity and therapeutic gain with aggregated scores. Patients with higher CORE scores at the outset of psychological therapy had longer not more intensive therapy. There was variation in treatment intensity between diagnostic clusters. Number of sessions, length of therapy (in weeks), and treatment intensity (the number of sessions per week between the first and last therapy sessions) were not related to therapeutic gains. These results fit with a responsive

Gut microbiota modifications and weight gain in early life

Directory of Open Access Journals (Sweden)

Emmanouil Angelakis

2018-04-01

Full Text Available Childhood and adolescent obesity is a significant public health concern and has been associated with cardiovascular disease and related metabolic sequelae later in life. In recent years, several studies have postulated an imbalance in the composition of the early life gut microbiota results in pediatric obesity and its associated diseases. The early life gut microbiota is influenced by several factors including the mode of delivery, prematurity, breastfeeding, and the use of antibiotics and probiotics. It has been proposed that, when given early in life, antibiotics and probiotics disrupt the gut microbiota and consequently its metabolic activity, promoting weight gain. Probiotics have increasingly been administrated to children and studies on the perinatal use of probiotics on low birth weight and healthy infants revealed significantly increased body length and weight later in life in comparison with infants who did not receive probiotic supplements. Similarly, exposure to antibiotics is very high perinatally and in the early periods of life and there is evidence that antibiotic treatment decreases the biodiversity of the early life gut microbiota. In addition, studies have revealed that antibiotic treatment during the first months of life is associated with being overweight later in life. In this paper we review the effects of the administration of probiotics and antibiotics in early life on the gut microbiota and discuss their effects on weight gain. Keywords: Gut microbiota, Obesity, Newborn, Antibiotics, Probiotics

Bk and Cf chromatographic separation and 249Bk/248Cm and 249Cf/248Cm elemental ratios determination by inductively coupled plasma quadrupole mass spectrometry

International Nuclear Information System (INIS)

Gourgiotis, A.; Isnard, H.; Nonell, A.; Aubert, M.; Stadelmann, G.; Dupont, E.; AlMahamid, I.; Tiang, G.; Rao, L.; Lukens, W.; Cassette, P.; Panebianco, S.; Letourneau, A.; Chartier, F.

2013-01-01

The French Atomic Energy Commission has carried out several experiments for the study of minor-actinide transmutation processes in high intensity thermal neutron flux. In this context a Cm sample enriched in 248 Cm (97%) was irradiated in a thermal neutron flux at the High Flux Reactor (HFR) of the Laue-Langevin Institute (ILL). The precise and accurate determination of Cf isotope ratios and of 249 Bk/ 248 Cm and 249 Cf/ 248 Cm elemental ratios in the 248 Cm irradiated sample is crucial for the calculation of actinide neutron capture cross-sections.This work describes an analytical procedure for the separation and the isotope ratio measurement of Bk and Cf in the irradiated sample.The Bk and Cf separation is based on a lanthanides separation protocol previously developed by the laboratory. Well-defined retention times for Bk and Cf were obtained by coupling the Ionic Chromatography (IC) with an ICP-QMS. All conditions of element separation by IC and the different steps of the analytical protocol in order to obtain the isotopic and elemental ratios are presented. Relative uncertainties of Cf isotopic ratios range from 0.3% to 0.5% and the uncertainty of the 249 Bk/ 248 Cm and 249 Cf/ 248 Cm elemental ratios are respectively 6.1% and 3.2%.This level of uncertainty for both isotopic and elemental ratios is in perfect agreement with the requirement for transmutation studies. (authors)

A novel solution to the gated x-ray detector gain droop problem

International Nuclear Information System (INIS)

Oertel, J. A.; Archuleta, T. N.

2014-01-01

Microchannel plate (MCP), microstrip transmission line based, gated x-ray detectors used at the premier ICF laser facilities have a drop in gain as a function of mircostrip length that can be greater than 50% over 40 mm. These losses are due to ohmic losses in a microstrip coating that is less than the optimum electrical skin depth. The electrical skin depth for a copper transmission line at 3 GHz is 1.2 μm while the standard microstrip coating thickness is roughly half a single skin depth. Simply increasing the copper coating thickness would begin filling the MCP pores and limit the number of secondary electrons created in the MCP. The current coating thickness represents a compromise between gain and ohmic loss. We suggest a novel solution to the loss problem by overcoating the copper transmission line with five electrical skin depths (∼6 μm) of Beryllium. Beryllium is reasonably transparent to x-rays above 800 eV and would improve the carrier current on the transmission line. The net result should be an optically flat photocathode response with almost no measurable loss in voltage along the transmission line

Gain control mechanisms in spinal motoneurons

Directory of Open Access Journals (Sweden)

Michael David Johnson

2014-07-01

Full Text Available Motoneurons provide the only conduit for motor commands to reach muscles. For many years, motoneurons were in fact considered to be little more than passive wires. Systematic studies in the past 25 years however have clearly demonstrated that the intrinsic electrical properties of motoneurons are under strong neuromodulatory control via multiple sources. The discovery of potent neuromodulation from the brainstem and its ability to change the gain of motoneurons shows that the passive view of the motor output stage is no longer tenable. A mechanism for gain control at the motor output stage makes good functional sense considering our capability of generating an enormous range of forces, from very delicate (e.g. putting in a contact lens to highly forceful (emergency reactions. Just as sensory systems need gain control to deal with a wide dynamic range of inputs, so to might motor output need gain control to deal with the wide dynamic range of the normal movement repertoire. Two problems emerge from the potential use of the brainstem monoaminergic projection to motoneurons for gain control. First, the projection is highly diffuse anatomically, so that independent control of the gains of different motor pools is not feasible. In fact, the system is so diffuse that gain for all the motor pools in a limb likely increases in concert. Second, if there is a system that increases gain, probably a system to reduce gain is also needed. In this review, we summarize recent studies that show local inhibitory circuits within the spinal cord, especially reciprocal and recurrent inhibition, have the potential to solve both of these problems as well as constitute another source of gain modulation.

How accurately can 21cm tomography constrain cosmology?

Science.gov (United States)

Mao, Yi; Tegmark, Max; McQuinn, Matthew; Zaldarriaga, Matias; Zahn, Oliver

2008-07-01

There is growing interest in using 3-dimensional neutral hydrogen mapping with the redshifted 21 cm line as a cosmological probe. However, its utility depends on many assumptions. To aid experimental planning and design, we quantify how the precision with which cosmological parameters can be measured depends on a broad range of assumptions, focusing on the 21 cm signal from 6noise, to uncertainties in the reionization history, and to the level of contamination from astrophysical foregrounds. We derive simple analytic estimates for how various assumptions affect an experiment’s sensitivity, and we find that the modeling of reionization is the most important, followed by the array layout. We present an accurate yet robust method for measuring cosmological parameters that exploits the fact that the ionization power spectra are rather smooth functions that can be accurately fit by 7 phenomenological parameters. We find that for future experiments, marginalizing over these nuisance parameters may provide constraints almost as tight on the cosmology as if 21 cm tomography measured the matter power spectrum directly. A future square kilometer array optimized for 21 cm tomography could improve the sensitivity to spatial curvature and neutrino masses by up to 2 orders of magnitude, to ΔΩk≈0.0002 and Δmν≈0.007eV, and give a 4σ detection of the spectral index running predicted by the simplest inflation models.

Magnetic susceptibility of 244Cm metal and 249Cf metal

International Nuclear Information System (INIS)

Fujita, D.K.; Parsons, T.C.; Edelstein, N.; Noe, M.; Peterson, J.R.

1975-07-01

The first magnetic susceptibility measurements made on the expanded fcc phase of 249 Cf metal are reported. Further measurements are needed on other Cf metal phases. Another measurement of the magnetic susceptibility of 244 Cm metal in a limited temperature range has been reported. The result does not agree with previously reported values. Further work is continuing on the synthesis of 244 Cm metal and 248 Cm metal and magnetic measurements on these samples. (auth)

Receiver Gain Modulation Circuit

Science.gov (United States)

Jones, Hollis; Racette, Paul; Walker, David; Gu, Dazhen

2011-01-01

A receiver gain modulation circuit (RGMC) was developed that modulates the power gain of the output of a radiometer receiver with a test signal. As the radiometer receiver switches between calibration noise references, the test signal is mixed with the calibrated noise and thus produces an ensemble set of measurements from which ensemble statistical analysis can be used to extract statistical information about the test signal. The RGMC is an enabling technology of the ensemble detector. As a key component for achieving ensemble detection and analysis, the RGMC has broad aeronautical and space applications. The RGMC can be used to test and develop new calibration algorithms, for example, to detect gain anomalies, and/or correct for slow drifts that affect climate-quality measurements over an accelerated time scale. A generalized approach to analyzing radiometer system designs yields a mathematical treatment of noise reference measurements in calibration algorithms. By treating the measurements from the different noise references as ensemble samples of the receiver state, i.e. receiver gain, a quantitative description of the non-stationary properties of the underlying receiver fluctuations can be derived. Excellent agreement has been obtained between model calculations and radiometric measurements. The mathematical formulation is equivalent to modulating the gain of a stable receiver with an externally generated signal and is the basis for ensemble detection and analysis (EDA). The concept of generating ensemble data sets using an ensemble detector is similar to the ensemble data sets generated as part of ensemble empirical mode decomposition (EEMD) with exception of a key distinguishing factor. EEMD adds noise to the signal under study whereas EDA mixes the signal with calibrated noise. It is mixing with calibrated noise that permits the measurement of temporal-functional variability of uncertainty in the underlying process. The RGMC permits the evaluation of EDA by

The value of Sonographic measurement of cervical length and fetal fibronectin testing in predicting preterm delivery

Directory of Open Access Journals (Sweden)

Zeki Salar

2007-03-01

Full Text Available OBJECTIVE: The aim of this study was to determine whether the combination of both fetal fibronectin and sonographic measurement of cervical length in women with preterm labor provides a better prediction than the individual tests alone.\tMETHODS: We examined 40 women with singleton pregnancies presenting at 24–35 (median 31 weeks of gestation with regular and painful uterine contractions, intact membranes and cervical dilatation of less than 3 cm. On admission to the hospital, fetal fibronectin positivity in cervicovaginal secretions was determined and transvaginal sonographic measurement of cervical length was carried out. The primary outcome measure was delivery within 14 days of presentation.\tRESULTS: Total of 40 eligible women at a mean gestational age of 28,3±4,8 weeks were enrolled from a population of 196 subjects screened. The overall prevalence of preterm delivery CONCLUSIONS: Combined the assessment of fetal fibronectin in cervico-vaginal secretions and the sonographic cervical length measurement improve the prediction of preterm delivery within 14 days in women with threatened preterm labor

Am/Cm Vitrification Process: Vitrification Material Balance Calculations

International Nuclear Information System (INIS)

Smith, F.G.

2000-01-01

This report documents material balance calculations for the Americium/Curium vitrification process and describes the basis used to make the calculations. The material balance calculations reported here start with the solution produced by the Am/Cm pretreatment process as described in ``Material Balance Calculations for Am/Cm Pretreatment Process (U)'', SRT-AMC-99-0178 [1]. Following pretreatment, small batches of the product will be further treated with an additional oxalic acid precipitation and washing. The precipitate from each batch will then be charged to the Am/Cm melter with glass cullet and vitrified to produce the final product. The material balance calculations in this report are designed to provide projected compositions of the melter glass and off-gas streams. Except for decanted supernate collected from precipitation and precipitate washing, the flowsheet neglects side streams such as acid washes of empty tanks that would go directly to waste. Complete listings of the results of the material balance calculations are provided in the Appendices to this report

Conflation of Short Identity-by-Descent Segments Bias Their Inferred Length Distribution

Directory of Open Access Journals (Sweden)

Charleston W. K. Chiang

2016-05-01

Full Text Available Identity-by-descent (IBD is a fundamental concept in genetics with many applications. In a common definition, two haplotypes are said to share an IBD segment if that segment is inherited from a recent shared common ancestor without intervening recombination. Segments several cM long can be efficiently detected by a number of algorithms using high-density SNP array data from a population sample, and there are currently efforts to detect shorter segments from sequencing. Here, we study a problem of identifiability: because existing approaches detect IBD based on contiguous segments of identity-by-state, inferred long segments of IBD may arise from the conflation of smaller, nearby IBD segments. We quantified this effect using coalescent simulations, finding that significant proportions of inferred segments 1–2 cM long are results of conflations of two or more shorter segments, each at least 0.2 cM or longer, under demographic scenarios typical for modern humans for all programs tested. The impact of such conflation is much smaller for longer (> 2 cM segments. This biases the inferred IBD segment length distribution, and so can affect downstream inferences that depend on the assumption that each segment of IBD derives from a single common ancestor. As an example, we present and analyze an estimator of the de novo mutation rate using IBD segments, and demonstrate that unmodeled conflation leads to underestimates of the ages of the common ancestors on these segments, and hence a significant overestimate of the mutation rate. Understanding the conflation effect in detail will make its correction in future methods more tractable.

Fundamental length, bubble electrons and non-local quantum electrodynamics

International Nuclear Information System (INIS)

Hsu, J.P.; Mac, E.

1977-06-01

Based on the concept of a bubble electron and the approach of Pais and Uhlenbeck, one constructs a finite quantum electrodynamics which is relativistically invariant, macro-causal and unitary. In this model, fields and their interaction are local, but the action function of free fields is nonlocal. The propagators are modified so that a fundamental length L is naturally introduced to physics. The modified static potential is given by V(r) = e/r for r greater than L and V(r) = 0 for r less than L, which is produced by the bubble source r -1 ddelta(r-L)/dr rather than a point source. It is found that L less than 4 x 10 -15 cm. Experimental consequences and modifications of strict causality at short distances, vertical bars 2 vertical bar approximately L 2 , are discussed

Energy Gaining Windows for Residental Buildings

DEFF Research Database (Denmark)

Kragh, Jesper; Laustsen, Jacob Birck; Svendsen, Svend

2008-01-01

This paper presents some of the research done during the last 8 years at the Technical University of Denmark developing improved low-energy window solutions. The focus has been on maximizing the net energy gain of windows for residential buildings. The net energy gain of windows is the solar gain...... minus the heat loss integrated over the heating season. It is assumed that in northern cold climates all of the solar gain during the heating season can be utilized for space heating. Problems with overheating in the summer period must be solved with overhang or moveable solar shading devices. Two...... and longer durability of the window. The glazing in these fiber reinforced polyester windows is both unsealed and sealed triple glazing units. To increase the net energy gain slim frame profiles have been developed to increase the glazing area and thereby the solar gain. The challenge when developing slim...

Intensity limits for propagation of 0.527 μm laser beams through large-scale-length plasmas for inertial confinement fusion

International Nuclear Information System (INIS)

Niemann, C.; Divol, L.; Froula, D.H.; Gregori, G.; Jones, O.; Kirkwood, R.K.; MacKinnon, A.J.; Meezan, N.B.; Moody, J.D.; Sorce, C.; Suter, L.J.; Glenzer, S.H.; Bahr, R.; Seka, W.

2005-01-01

We have established the intensity limits for propagation of a frequency-doubled (2ω, 527 nm) high intensity interaction beam through an underdense large-scale-length plasma. We observe good beam transmission at laser intensities at or below 2x10 14 W/cm 2 and a strong reduction at intensities up to 10 15 W/cm 2 due to the onset of parametric scattering instabilities. We show that temporal beam smoothing by spectral dispersion allows a factor of 2 higher intensities while keeping the beam spray constant, which establishes frequency-doubled light as an option for ignition and burn in inertial confinement fusion experiments

Control of gain in conjugated polymers and perylene dyes

International Nuclear Information System (INIS)

Sheridan, A.

2001-03-01

This thesis presents an investigation into the factors which control the gain and amplification properties in conjugated materials. Conjugated polymers and perylene dyes are highly fluorescent, are easy to process into thin films, and exhibit strong amplification over a broad gain bandwidth making them ideal for use in lasers and amplifiers. The stimulated emission created when thin films of the red emitting polymer poly(2-methoxy-5-(2'-ethylhexyloxy)-p-phenylenvinylene) (MEH-PPV) were photoexcited with high energy laser pulses was investigated. This was characterised by a dramatic narrowing of the emission spectrum which has been assigned to amplified spontaneous emission (ASE). The emission was found to have a gaussian profile and the gain coefficient was found to be 4 cm -1 . The temperature dependence of the absorption, photoluminescence and ASE of films of MEH-PPV was measured. The effect of film morphology on the photophysical properties was investigated by using films cast from two spinning solvents, chlorobenzene (CB) and tetrahydrofuran (THF). Film morphology was found to greatly affect the temperature dependence. A particularly important property is the spectral position of the ASE and the factors which affect it. By controlling the film thickness close to the cut-off thickness for waveguiding in the polymer film it was shown that the peak position of the ASE could be tuned by 31 nm. Modelling of the waveguide modes in the polymer films was used to explain this effect. The cut-off wavelength for each film was measured and good agreement with the theory was found. In order to investigate ways in which energy transfer could be used to control the emission, two perylene dyes were used as a donor-acceptor pair in a host matrix of poly methymethacralate (PMMA). The position of the ASE was found to depend on the acceptor concentration. Measurements of the photoluminescence quantum yield and time-resolved luminescence measurements showed that the energy transfer

Optimal weight gain in triplet pregnancies.

Science.gov (United States)

Johnston, Robert C; Erfani, Hadi; Shamshirsaz, Amir A; Spiel, Melissa; Ravangard, Sam F; Shaman, Majid; Allaf, M Baraa; Shamshirsaz, Alireza A; Haeri, Sina

2017-08-01

To identify appropriate weight gain in triplet gestations, which may aid in reducing the risk of perinatal morbidity within this high-risk cohort. This retrospective cohort study evaluated all non-anomalous triplet pregnancies between 23 and 40 weeks' gestation resulting in live births at five tertiary-care medical centers between 1991 and 2011. Subjects were divided by pre-pregnancy BMI into underweight, normal-weight, overweight, and obese groups, and then stratified by low (gain (≥1.5 lbs/week). Primary outcomes included spontaneous preterm birth and preeclampsia. We included 116 mothers and 348 corresponding neonates for final analysis. The incidence of preeclampsia and preterm delivery less than 32 weeks' gestation was 37% and 41%, respectively. The incidence of preeclampsia increased with weight gain per week, but was not statistically different from subjects who gained less weight. We found no statistical correlation between weight gain per week and preterm delivery. We found no association between preeclampsia or preterm delivery and increasing weight gain in triplet pregnancies. The association with increased risk for preeclampsia was predominantly due to BMI effect. Based on the current study, recommendations for optimal weight gain in mothers with triplet gestations could not be defined.

TERT promoter mutations and long telomere length predict poor survival and radiotherapy resistance in gliomas.

Science.gov (United States)

Gao, Ke; Li, Gang; Qu, Yiping; Wang, Maode; Cui, Bo; Ji, Meiju; Shi, Bingyin; Hou, Peng

2016-02-23

Increasing evidences have implicated somatic gain-of-function mutations at the telomerase reverse transcriptase (TERT) promoter as one of the major mechanisms that promote transcriptional activation of TERT and subsequently maintain telomere length in human cancers including glioma. To investigate the prognostic value of these mutations and telomere length, individually and their coexistence, in gliomas, we analyzed two somatic mutations C228T and C250T in the TERT promoter, relative telomere length (RTL), IDH1 mutation and MGMT methylation in 389 glioma patients, and explored their associations with patient characteristics and clinical outcomes. Our data showed that C228T and C250T mutations were found in 17.0% (66 of 389) and 11.8% (46 of 389) of gliomas, respectively, and these two mutations were mutually exclusive in this cancer. Moreover, they were significantly associated with WHO grade. We also found that the RTL was significant longer in gliomas than in meningiomas and normal brain tissues (Median, 0.89 vs. 0.44 and 0.50; P radiotherapy. Collectively, TERT promoter mutations and long RTL are not only prognostic factors for poor clinical outcomes, but also the predictors of radiotherapy resistance in gliomas.

Generation of Length Distribution, Length Diagram, Fibrogram, and Statistical Characteristics by Weight of Cotton Blends

Directory of Open Access Journals (Sweden)

B. Azzouz

2007-01-01

Full Text Available The textile fibre mixture as a multicomponent blend of variable fibres imposes regarding the proper method to predict the characteristics of the final blend. The length diagram and the fibrogram of cotton are generated. Then the length distribution, the length diagram, and the fibrogram of a blend of different categories of cotton are determined. The length distributions by weight of five different categories of cotton (Egyptian, USA (Pima, Brazilian, USA (Upland, and Uzbekistani are measured by AFIS. From these distributions, the length distribution, the length diagram, and the fibrogram by weight of four binary blends are expressed. The length parameters of these cotton blends are calculated and their variations are plotted against the mass fraction x of one component in the blend .These calculated parameters are compared to those of real blends. Finally, the selection of the optimal blends using the linear programming method, based on the hypothesis that the cotton blend parameters vary linearly in function of the components rations, is proved insufficient.

Estimation of genetic variability and selection response for clutch length in dwarf brown-egg layers carrying or not the naked neck gene

Directory of Open Access Journals (Sweden)

Tixier-Boichard Michèle

2003-03-01

Full Text Available Abstract In order to investigate the possibility of using the dwarf gene for egg production, two dwarf brown-egg laying lines were selected for 16 generations on average clutch length; one line (L1 was normally feathered and the other (L2 was homozygous for the naked neck gene NA. A control line from the same base population, dwarf and segregating for the NA gene, was maintained during the selection experiment under random mating. The average clutch length was normalized using a Box-Cox transformation. Genetic variability and selection response were estimated either with the mixed model methodology, or with the classical methods for calculating genetic gain, as the deviation from the control line, and the realized heritability, as the ratio of the selection response on cumulative selection differentials. Heritability of average clutch length was estimated to be 0.42 ± 0.02, with a multiple trait animal model, whereas the estimates of the realized heritability were lower, being 0.28 and 0.22 in lines L1 and L2, respectively. REML estimates of heritability were found to decline with generations of selection, suggesting a departure from the infinitesimal model, either because a limited number of genes was involved, or their frequencies were changed. The yearly genetic gains in average clutch length, after normalization, were estimated to be 0.37 ± 0.02 and 0.33 ± 0.04 with the classical methods, 0.46 ± 0.02 and 0.43 ± 0.01 with animal model methodology, for lines L1 and L2 respectively, which represented about 30% of the genetic standard deviation on the transformed scale. Selection response appeared to be faster in line L2, homozygous for the NA gene, but the final cumulated selection response for clutch length was not different between the L1 and L2 lines at generation 16.

Word length, set size, and lexical factors: Re-examining what causes the word length effect.

Science.gov (United States)

Guitard, Dominic; Gabel, Andrew J; Saint-Aubin, Jean; Surprenant, Aimée M; Neath, Ian

2018-04-19

The word length effect, better recall of lists of short (fewer syllables) than long (more syllables) words has been termed a benchmark effect of working memory. Despite this, experiments on the word length effect can yield quite different results depending on set size and stimulus properties. Seven experiments are reported that address these 2 issues. Experiment 1 replicated the finding of a preserved word length effect under concurrent articulation for large stimulus sets, which contrasts with the abolition of the word length effect by concurrent articulation for small stimulus sets. Experiment 2, however, demonstrated that when the short and long words are equated on more dimensions, concurrent articulation abolishes the word length effect for large stimulus sets. Experiment 3 shows a standard word length effect when output time is equated, but Experiments 4-6 show no word length effect when short and long words are equated on increasingly more dimensions that previous demonstrations have overlooked. Finally, Experiment 7 compared recall of a small and large neighborhood words that were equated on all the dimensions used in Experiment 6 (except for those directly related to neighborhood size) and a neighborhood size effect was still observed. We conclude that lexical factors, rather than word length per se, are better predictors of when the word length effect will occur. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

24 GHz cmWave Radio Propagation Through Vegetation

DEFF Research Database (Denmark)

Rodriguez, Ignacio; Abreu, Renato Barbosa; Portela Lopes de Almeida, Erika

2016-01-01

This paper presents a measurement-based analysis of cm-wave radio propagation through vegetation at 24 GHz. A set of dedicated directional measurements were performed with horn antennas located close to street level inside a densely-vegetated area illuminated from above. The full azimuth was exam......This paper presents a measurement-based analysis of cm-wave radio propagation through vegetation at 24 GHz. A set of dedicated directional measurements were performed with horn antennas located close to street level inside a densely-vegetated area illuminated from above. The full azimuth...

Capillary Versus Aspiration Biopsy: Effect of Needle Size and Length on the Cytopathological Specimen Quality

International Nuclear Information System (INIS)

Hopper, Kenneth D.; Grenko, Ronald T.; Fisher, Alicia I.; TenHave, Thomas R.

1996-01-01

Purpose: To test the value of the nonaspiration, or capillary, biopsy technique by experimental comparison with the conventional fine-needle aspiration technique using various needle gauges and lengths. Methods: On fresh hepatic and renal tissue from five autopsies, multiple biopsy specimens were taken with 20, 22, and 23-gauge Chiba needles of 5, 10, 15, and 20-cm length, using the aspiration technique and the capillary technique. The resultant specimens were graded on the basis of a grading scheme by a cytopathologist who was blinded to the biopsy technique. Results: The capillary technique obtained less background blood or clot which could obscure diagnostic tissue, although not significantly different from the aspiration technique (p= 0.2). However, for the amount of cellular material obtained, retention of appropriate architecture, and mean score, the capillary technique performed statistically worse than aspiration biopsy (p < 0.01). In addition, with decreasing needle caliber (increasing needle gauge) and increasing length, the capillary biopsy was inferior to the aspiration biopsy. Conclusion: The capillary biopsy technique is inferior to the aspiration technique according to our study. When the capillary technique is to be applied, preference should be given to larger caliber, shorter needles

Gap length distributions by PEPR

International Nuclear Information System (INIS)

Warszawer, T.N.

1980-01-01

Conditions guaranteeing exponential gap length distributions are formulated and discussed. Exponential gap length distributions of bubble chamber tracks first obtained on a CRT device are presented. Distributions of resulting average gap lengths and their velocity dependence are discussed. (orig.)

Expected genetic gain in teak (Tectona grandis L.f.) in Cordoba (Colombia)

International Nuclear Information System (INIS)

Espitia C, Miguel; Olman Murillo, G; Carlos Castillo, P

2011-01-01

The Cordoba department of Colombia programmed to establish 200000 ha of forest plantations by year 2025. Teak was priorized by its adaptation, wood quality and value in the asian markets. The objective of this research was to estimate the expected genetic gain, of phenotypically selected pluss trees in 5316 ha plantation in Cordoba, for diameter at breast height, commercial height, commercial volume and log quality traits. The selection based on the pheno typical evaluation of the tree candidate and its four best neighbors within a 20 m radius, qualifying, individually the first four segments of 2.5 m length. Selected trees were classified in list A as determined to be superior in both, volume and quality, according to the selection differential to all its four best neighbors. List B included those plus trees found superior only in commercial volume or in stem quality. Genetic gain was estimated by multiplying selection differential X average narrow sense heritability. We estimated a Selection Index that integrate commercial volume (60%) and stem quality (40%). From 46 selected trees, 18 were classified as plus A. In selecting and cloning the 18 best A plus trees, based on the Selection Index, we expected genetic gains of 5.52% (diameter); 17.50% (height); 41.71% (commercial volume) and 9,59% (stem quality). These results suggest an important genetic progress breeding teak in Cordoba, as long as they broaden the genetic base of the program and verify results with genetic testing in various potential production areas.

Weight suppression predicts total weight gain and rate of weight gain in outpatients with anorexia nervosa.

Science.gov (United States)

Carter, Frances A; Boden, Joseph M; Jordan, Jennifer; McIntosh, Virginia V W; Bulik, Cynthia M; Joyce, Peter R

2015-11-01

The present study sought to replicate the finding of Wildes and Marcus, Behav Res Ther, 50, 266-274, 2012 that higher levels of weight suppression at pretreatment predict greater total weight gain, faster rate of weight gain, and bulimic symptoms amongst patients admitted with anorexia nervosa. Participants were 56 women with anorexia nervosa diagnosed by using strict or lenient weight criteria, who were participating in a randomized controlled psychotherapy trial (McIntosh et al., Am J Psychiatry, 162, 741-747, 2005). Thirty-five women completed outpatient treatment and post-treatment assessment. Weight suppression was the discrepancy between highest lifetime weight at adult height and weight at pretreatment assessment. Outcome variables were total weight gain, rate of weight gain, and bulimic symptoms in the month prior to post-treatment assessment [assessed using the Eating Disorders Examination (Fairburn et al., Binge-Eating: Nature, Assessment and Treatment. New York: Guilford, 1993)]. Weight suppression was positively associated with total weight gain and rate of weight gain over treatment. Regression models showed that this association could not be explained by covariates (age at onset of anorexia nervosa and treatment modality). Weight suppression was not significantly associated with bulimic symptoms in the month prior to post-treatment assessment, regardless of whether bulimic symptoms were examined as continuous or dichotomous variables. The present study reinforces the previous finding that weight suppression predicts total weight gain and rate of weight gain amongst patients being treated for anorexia nervosa. Methodological issues may explain the failure of the present study to find that weight suppression predicts bulimic symptoms. Weight suppression at pretreatment for anorexia nervosa should be assessed routinely and may inform treatment planning. © 2015 Wiley Periodicals, Inc.

Effects of fine root length density and root biomass on soil preferential flow in forest ecosystems

Directory of Open Access Journals (Sweden)

Yinghu Zhang

2015-04-01

Full Text Available Aim of study: The study was conducted to characterize the impacts of plant roots systems (e.g., root length density and root biomass on soil preferential flow in forest ecosystems. Area of study: The study was carried out in Jiufeng National Forest Park, Beijing, China. Material and methods: The flow patterns were measured by field dye tracing experiments. Different species (Sophora japonica Linn,Platycladus orientalis Franco, Quercus dentata Thunbwere quantified in two replicates, and 12 soil depth were applied. Plant roots were sampled in the sieving methods. Root length density and root biomass were measured by WinRHIZO. Dye coverage was implied in the image analysis, and maximum depth of dye infiltration by direct measurement. Main results: Root length density and root biomass decreased with the increasing distance from soil surface, and root length density was 81.6% higher in preferential pathways than in soil matrix, and 66.7% for root biomass with respect to all experimental plots. Plant roots were densely distributed in the upper soil layers. Dye coverage was almost 100% in the upper 5-10 cm, but then decreased rapidly with soil depth. Root length density and root biomass were different from species: Platycladus orientalis Franco > Quercus dentata Thunb > Sophora japonica Linn. Research highlights: The results indicated that fine roots systems had strong effects on soil preferential flow, particularly root channels enhancing nutrition transport across soil profiles in forest dynamics.

Measurement of Antenna Bore-Sight Gain

Science.gov (United States)

Fortinberry, Jarrod; Shumpert, Thomas H.

2016-01-01

The absolute or free-field gain of a simple antenna can be approximated using standard antenna theory formulae or for a more accurate prediction, numerical methods may be employed to solve for antenna parameters including gain. Both of these methods will result in relatively reasonable estimates but in practice antenna gain is usually verified and documented via measurements and calibration. In this paper, a relatively simple and low-cost, yet effective means of determining the bore-sight free-field gain of a VHF/UHF antenna is proposed by using the Brewster angle relationship.

'CM 88' - A multiple disease resistant chickpea mutant variety

International Nuclear Information System (INIS)

Haq, M.A.; Hassan, Mahmudul; Sadiq, M.

2001-01-01

Full text: Chickpea is the most important grain legume crop of Pakistan. Ascochyta blight (Ascochyta rabiei) and Fusarium wilt (Fusarium oxysporum F. sp cicer) are most serious diseases, having the potential to devastate a crop. A multiple disease resistant and high yielding mutant CM 88 has been developed through 100 Gy gamma irradiation treatment of variety 'C 727'. This was once a widely grown and popular variety, which lost its resistance to Ascochyta and was replaced. The selection of mutants was performed in the M2 generation grown in the Ascochyta blight nursery and sixteen mutants were selected. In the subsequent generations CM 88 proved resistant to both Ascochyta blight and Fusarium wilt, and exhibited superiority in agronomic characteristics. CM 88 was also tested for many years in the various yield trials on research stations and farmers fields throughout the country. In these trials it out yielded both the parent and standard varieties. The mutant CM 88 has been approved by the Punjab Seed Council on 27 October 1994 for general cultivation in the Punjab Province, especially the Thal area which accounts for more than 70% of the area under chickpea cultivation. (author)

The 21-cm Signal from the cosmological epoch of recombination

Energy Technology Data Exchange (ETDEWEB)

Fialkov, A. [Departement de Physique, Ecole Normale Superieure, CNRS, 24 rue Lhomond, Paris, 75005 (France); Loeb, A., E-mail: anastasia.fialkov@phys.ens.fr, E-mail: aloeb@cfa.harvard.edu [Department of Astronomy, Harvard University, 60 Garden Street, MS-51, Cambridge, MA, 02138 (United States)

2013-11-01

The redshifted 21-cm emission by neutral hydrogen offers a unique tool for mapping structure formation in the early universe in three dimensions. Here we provide the first detailed calculation of the 21-cm emission signal during and after the epoch of hydrogen recombination in the redshift range of z ∼ 500–1,100, corresponding to observed wavelengths of 100–230 meters. The 21-cm line deviates from thermal equilibrium with the cosmic microwave background (CMB) due to the excess Lyα radiation from hydrogen and helium recombinations. The resulting 21-cm signal reaches a brightness temperature of a milli-Kelvin, orders of magnitude larger than previously estimated. Its detection by a future lunar or space-based observatory could improve dramatically the statistical constraints on the cosmological initial conditions compared to existing two-dimensional maps of the CMB anisotropies.

The 21-cm Signal from the cosmological epoch of recombination

International Nuclear Information System (INIS)

Fialkov, A.; Loeb, A.

2013-01-01

The redshifted 21-cm emission by neutral hydrogen offers a unique tool for mapping structure formation in the early universe in three dimensions. Here we provide the first detailed calculation of the 21-cm emission signal during and after the epoch of hydrogen recombination in the redshift range of z ∼ 500–1,100, corresponding to observed wavelengths of 100–230 meters. The 21-cm line deviates from thermal equilibrium with the cosmic microwave background (CMB) due to the excess Lyα radiation from hydrogen and helium recombinations. The resulting 21-cm signal reaches a brightness temperature of a milli-Kelvin, orders of magnitude larger than previously estimated. Its detection by a future lunar or space-based observatory could improve dramatically the statistical constraints on the cosmological initial conditions compared to existing two-dimensional maps of the CMB anisotropies

Gain scheduling using the Youla parameterization

DEFF Research Database (Denmark)

Niemann, Hans Henrik; Stoustrup, Jakob

1999-01-01

Gain scheduling controllers are considered in this paper. The gain scheduling problem where the scheduling parameter vector cannot be measured directly, but needs to be estimated is considered. An estimation of the scheduling vector has been derived by using the Youla parameterization. The use...... in connection with H_inf gain scheduling controllers....

Nanoscale charcoal powder induced saturable absorption and mode-locking of a low-gain erbium-doped fiber-ring laser

International Nuclear Information System (INIS)

Lin, Yung-Hsiang; Chi, Yu-Chieh; Lin, Gong-Ru

2013-01-01

Triturated charcoal nano-powder directly brushed on a fiber connector end-face is used for the first time as a fast saturable absorber for a passively mode-locked erbium-doped fiber-ring laser (EDFL). These dispersant-free charcoal nano-powders with a small amount of crystalline graphene phase and highly disordered carbon structure exhibit a broadened x-ray diffraction peak and their Raman spectrum shows the existence of a carbon related D-band at 1350 cm −1 and the disappearance of the 2D-band peak at 2700 cm −1 . The charcoal nano-powder exhibits a featureless linear absorbance in the infrared region with its linear transmittance of 0.66 nonlinearly saturated at 0.73 to give a ΔT/T of 10%. Picosecond mode-locking at a transform-limited condition of a low-gain EDFL is obtained by using the charcoal nano-powder. By using a commercial EDFA with a linear gain of only 17 dB at the saturated output power of 17.5 dB m required to initiate the saturable absorption of the charcoal nano-powder, the EDFL provides a pulsewidth narrowing from 3.3 to 1.36 ps associated with its spectral linewidth broadening from 0.8 to 1.83 nm on increasing the feedback ratio from 30 to 90%. This investigation indicates that all the carbon-based materials containing a crystalline graphene phase can be employed to passively mode-lock the EDFL, however, the disordered carbon structure inevitably induces a small modulation depth and a large mode-locking threshold, thus limiting the pulsewidth shortening. Nevertheless, the nanoscale charcoal passively mode-locked EDFL still shows the potential to generate picosecond pulses under a relatively low cavity gain. An appropriate cavity design can be used to compensate this defect-induced pulsewidth limitation and obtain a short pulsewidth. (letter)

Cutting Whole Length or Partial Length of Internal Anal Sphincter in Managementof Fissure in Ano

Directory of Open Access Journals (Sweden)

Furat Shani Aoda

2017-12-01

Full Text Available A chronic anal fissure is a common painful perianal condition.The main operative procedure to treat this painful condition is a lateral internal sphincteretomy (LIS.The aim of study is to compare the outcome and complications of closed LIS up to the dentate line (whole length of internal sphincter or up to the fissure apex (partial length of internal sphincter in the treatment of anal fissure.It is a prospective comparativestudy including 100 patients with chronic fissure in ano. All patients assigned to undergo closed LIS. Those patients were randomly divided into two groups: 50 patients underwent LIS to the level of dentate line (whole length and other 50 patients underwent LIS to the level of fissure apex (partial length. Patients were followed up weekly in the 1st month, twice monthly in the second month then monthly   for next 2 months and finally after 1 year. There was satisfactory relief of pain in all patients in both groups & complete healing of the fissure occurred. Regarding post operative incontinence no major degree of incontinence occur in both group but minor degree of incontinence persists In 7 patients after whole length LIS after one year. In conclusion, both whole length & partial length LIS associated with improvement of pain, good chance of healing but whole length LIS associated with more chance of long term  flatus incontinence. Hence,we recommend partial length LIS as treatment forchronic anal fissure.

Maternal weight gain and associations with longitudinal fetal growth in dichorionic twin pregnancies: a prospective cohort study.

Science.gov (United States)

Hinkle, Stefanie N; Hediger, Mary L; Kim, Sungduk; Albert, Paul S; Grobman, William; Newman, Roger B; Wing, Deborah A; Grewal, Jagteshwar; Zhang, Cuilin; Buck Louis, Germaine M; Grantz, Katherine L

2017-12-01

Background: Maternal metabolic demands are much greater with twin gestations; however, there are no accepted recommendations for maternal weight gain in twin pregnancies. Objective: We assessed the association of maternal weight gain and fetal growth in dichorionic twins throughout pregnancy. Design: This was a prospective US cohort study ( n = 143, 2012-2013) of dichorionic twin pregnancies with known birth outcomes followed from enrollment (11-13 wk) and for ≤6 research visits throughout gestation. Maternal prepregnancy weight was self-reported, and current weight was measured at each research visit and abstracted from prenatal records. Fetal biometry was assessed by ultrasound at each research visit. Maternal weight and twin-pair fetal size trajectories across gestation were modeled. The adjusted associations between maternal weight gain from 0 to 13, 14 to 20, 21 to 27, and 28 to 34 wk and fetal growth at the subsequent week (i.e., 14, 21, 28, and 35 wk, respectively) were estimated with the use of linear regression. Results: The mean ± SD maternal weight gain from 0 to 13, 14 to 20, 21 to 27, and 28 to 34 wk was 2.8 ± 3.0 kg, 3.9 ± 1.2 kg, 3.8 ± 1.4 kg, and 4.4 ± 2.2 kg, respectively, with a total gain of 17.7 ± 7.4 kg. Maternal weight gain from 0 to 13 wk (first trimester) was not associated with fetal size at 14 wk. Maternal weight gain from 14 to 20 and 21 to 27 wk (second trimester) was significantly associated with increased fetal weight at 21 wk [increase of 10.5 g/kg maternal weight gain (95% CI: 1.2, 19.8 g)] and 28 wk [increase of 21.3 g/kg maternal weight gain (95% CI: 0.6, 42.0 g)]. Maternal weight gain from 14 to 20 wk was associated with increased twin abdominal circumference (AC) and biparietal diameter at 21 wk. Maternal weight gain from 21 to 27 wk was associated with increased femur and humerus lengths at 28 wk. Conclusion: Maternal weight gain was associated with dichorionic twin fetal growth in the second trimester only, driven by an

Analysing 21cm signal with artificial neural network

Science.gov (United States)

Shimabukuro, Hayato; a Semelin, Benoit

2018-05-01

The 21cm signal at epoch of reionization (EoR) should be observed within next decade. We expect that cosmic 21cm signal at the EoR provides us both cosmological and astrophysical information. In order to extract fruitful information from observation data, we need to develop inversion method. For such a method, we introduce artificial neural network (ANN) which is one of the machine learning techniques. We apply the ANN to inversion problem to constrain astrophysical parameters from 21cm power spectrum. We train the architecture of the neural network with 70 training datasets and apply it to 54 test datasets with different value of parameters. We find that the quality of the parameter reconstruction depends on the sensitivity of the power spectrum to the different parameter sets at a given redshift and also find that the accuracy of reconstruction is improved by increasing the number of given redshifts. We conclude that the ANN is viable inversion method whose main strength is that they require a sparse extrapolation of the parameter space and thus should be usable with full simulation.

Length and sequence dependence in the association of Huntingtin protein with lipid membranes

Science.gov (United States)

Jawahery, Sudi; Nagarajan, Anu; Matysiak, Silvina

2013-03-01

There is a fundamental gap in our understanding of how aggregates of mutant Huntingtin protein (htt) with overextended polyglutamine (polyQ) sequences gain the toxic properties that cause Huntington's disease (HD). Experimental studies have shown that the most important step associated with toxicity is the binding of mutant htt aggregates to lipid membranes. Studies have also shown that flanking amino acid sequences around the polyQ sequence directly affect interactions with the lipid bilayer, and that polyQ sequences of greater than 35 glutamine repeats in htt are a characteristic of HD. The key steps that determine how flanking sequences and polyQ length affect the structure of lipid bilayers remain unknown. In this study, we use atomistic molecular dynamics simulations to study the interactions between lipid membranes of varying compositions and polyQ peptides of varying lengths and flanking sequences. We find that overextended polyQ interactions do cause deformation in model membranes, and that the flanking sequences do play a role in intensifying this deformation by altering the shape of the affected regions.

Telomere length and depression

DEFF Research Database (Denmark)

Wium-Andersen, Marie Kim; Ørsted, David Dynnes; Rode, Line

2017-01-01

BACKGROUND: Depression has been cross-sectionally associated with short telomeres as a measure of biological age. However, the direction and nature of the association is currently unclear. AIMS: We examined whether short telomere length is associated with depression cross-sectionally as well...... as prospectively and genetically. METHOD: Telomere length and three polymorphisms, TERT, TERC and OBFC1, were measured in 67 306 individuals aged 20-100 years from the Danish general population and associated with register-based attendance at hospital for depression and purchase of antidepressant medication....... RESULTS: Attendance at hospital for depression was associated with short telomere length cross-sectionally, but not prospectively. Further, purchase of antidepressant medication was not associated with short telomere length cross-sectionally or prospectively. Mean follow-up was 7.6 years (range 0...

High Gain Advanced GPS Receiver

National Research Council Canada - National Science Library

Brown, Alison; Zhang, Gengsheng

2006-01-01

NAVSYS High Gain Advanced GPS Receiver (HAGR) uses a digital beam-steering antenna array to enable up to eight GPS satellites to be tracked, each with up to 10 dBi of additional antenna gain over a conventional receiver solution...

Estimating age from recapture data: integrating incremental growth measures with ancillary data to infer age-at-length

Science.gov (United States)

Eaton, Mitchell J.; Link, William A.

2011-01-01

Estimating the age of individuals in wild populations can be of fundamental importance for answering ecological questions, modeling population demographics, and managing exploited or threatened species. Significant effort has been devoted to determining age through the use of growth annuli, secondary physical characteristics related to age, and growth models. Many species, however, either do not exhibit physical characteristics useful for independent age validation or are too rare to justify sacrificing a large number of individuals to establish the relationship between size and age. Length-at-age models are well represented in the fisheries and other wildlife management literature. Many of these models overlook variation in growth rates of individuals and consider growth parameters as population parameters. More recent models have taken advantage of hierarchical structuring of parameters and Bayesian inference methods to allow for variation among individuals as functions of environmental covariates or individual-specific random effects. Here, we describe hierarchical models in which growth curves vary as individual-specific stochastic processes, and we show how these models can be fit using capture–recapture data for animals of unknown age along with data for animals of known age. We combine these independent data sources in a Bayesian analysis, distinguishing natural variation (among and within individuals) from measurement error. We illustrate using data for African dwarf crocodiles, comparing von Bertalanffy and logistic growth models. The analysis provides the means of predicting crocodile age, given a single measurement of head length. The von Bertalanffy was much better supported than the logistic growth model and predicted that dwarf crocodiles grow from 19.4 cm total length at birth to 32.9 cm in the first year and 45.3 cm by the end of their second year. Based on the minimum size of females observed with hatchlings, reproductive maturity was estimated

Determination of the STIS CCD Gain

Science.gov (United States)

Riley, Allyssa; Monroe, TalaWanda; Lockwood, Sean

2016-09-01

This report summarizes the analysis and absolute gain results of the STIS Cycle 23 special calibration program 14424 that was designed to measure the gain of amplifiers A, C and D at nominal gain settings of 1 and 4 e-/DN. We used the mean-variance technique and the results indicate a mean-variance technique.

Neutron resonance parameters of CM isotopes

International Nuclear Information System (INIS)

Belanova, T.S.; Kolesov, A.G.; Poruchikov, V.A.

1977-01-01

The total neutron cross sections of isotopes 244, 245, 246, 248 Curium have been measured on reactor CM-2 using the time-of-flight method. Single-level Breit-Wigner resonance parameters: energy E 0 , neutron width 2g GITAn, total width GITA, total neutron cross section in resonance sigma 0 have been obtained by the shape and area methods

Long length coated conductor fabrication by inclined substrate deposition and evaporation

Energy Technology Data Exchange (ETDEWEB)

Prusseit, W [THEVA Duennschichttechnik GmbH, Rote-Kreuz-Str. 8, 85737 Ismaning (Germany); Hoffmann, C [THEVA Duennschichttechnik GmbH, Rote-Kreuz-Str. 8, 85737 Ismaning (Germany); Nemetschek, R [THEVA Duennschichttechnik GmbH, Rote-Kreuz-Str. 8, 85737 Ismaning (Germany); Sigl, G [THEVA Duennschichttechnik GmbH, Rote-Kreuz-Str. 8, 85737 Ismaning (Germany); Handke, J [THEVA Duennschichttechnik GmbH, Rote-Kreuz-Str. 8, 85737 Ismaning (Germany); Luemkemann, A [Technical University Munich, James- Franck-Str. 1, 85748 Garching (Germany); Kinder, H [Technical University Munich, James- Franck-Str. 1, 85748 Garching (Germany)

2006-06-01

The commercial development of coated conductors is rapidly progressing. As a result we present an economic route to produce second generation HTS tape from the initial substrate preparation to the final metal coating. The most important and technically challenging steps are the deposition of an oriented buffer layer and the superconductor film in a reel-to-reel configuration. New evaporation techniques have been developed to enable reliable, high rate tape coating. Highly oriented MgO - buffer layers are realized by inclined substrate deposition (ISD) and DyBCO is deposited by simple e-gun evaporation yielding critical currents beyond 200 A/cm. Coated conductors have been fabricated up to 40 m length and are currently tested in a variety of applications.

First operation and performance of a 200 lt double phase LAr LEM-TPC with a 40x76 $\\cm^2$ readout

CERN Document Server

Badertscher, A; Degunda, U; Epprecht, L; Gendotti, A; Horikawa, S; Knecht, L; Natterer, D Lussi G; Nguyen, K; Resnati, F; Rubbia, A; Viant, T

2013-01-01

In this paper we describe the design, construction, and operation of a first large area double-phase liquid argon Large Electron Multiplier Time Projection Chamber (LAr LEM-TPC). The detector has a maximum drift length of 60 cm and the readout consists of a $40\\times 76$ cm$^2$ LEM and 2D projective anode to multiply and collect drifting charges. Scintillation light is detected by means of cryogenic PMTs positioned below the cathode. To record both charge and light signals, we have developed a compact acquisition system, which is scalable up to ton-scale detectors with thousands of charge readout channels. The acquisition system, as well as the design and the performance of custom-made charge sensitive preamplifiers, are described. The complete experimental setup has been operated for a first time during a period of four weeks at CERN in the cryostat of the ArDM experiment, which was equipped with liquid and gas argon purification systems. The detector, exposed to cosmic rays, recorded events with a single-ch...

Nonunity gain minimal-disturbance measurement

DEFF Research Database (Denmark)

Sabuncu, Metin; Mišta, L.; Fiurášek, J.

2007-01-01

We propose and experimentally demonstrate an optimal nonunity gain Gaussian scheme for partial measurement of an unknown coherent state that causes minimal disturbance of the state. The information gain and the state disturbance are quantified by the noise added to the measurement outcomes...

Optical gain at 1.53 {mu}m in Er{sup 3+}-Yb{sup 3+} co-doped porous silicon waveguides

Energy Technology Data Exchange (ETDEWEB)

Najar, A. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia)], E-mail: najar.adel@laposte.net; Charrier, J. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Ajlani, H. [Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia); Lorrain, N.; Haesaert, S. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France); Oueslati, M. [Laboratoire de Spectroscopie Raman, Faculte des Sciences de Tunis, 2092 El Manar, Tunis (Tunisia); Haji, L. [Laboratoire d' Optronique UMR 6082-FOTON, Universite de Rennes 1, 6 rue de Kerampont, BP 80518, 22305 Lannion Cedex (France)

2008-01-15

Erbium-ytterbium (Er-Yb)-co-doped porous silicon planar waveguides were prepared from P{sup +}-type (1 0 0) oriented silicon wafer. Erbium and ytterbium ions were electrochemically introduced into the porous structure of the waveguide core. The doping profiles of erbium and ytterbium ions were determined by EDX analysis performed on sample cross-section. The mean concentration in the guiding layer is of about 1 x 10{sup 20} cm{sup -3}. The refractive indices were measured from co-doped porous silicon and undoped waveguides after the thermal treatments. The photoluminescence (PL) peak of optically activated erbium ions at 1.53 {mu}m was recorded. The PL enhancement is the result of the energy transfer from the excited state of Yb to the state of Er. Optical losses at 1.55 {mu}m were measured on these waveguides and were of about 2 dB/cm. An internal gain at 1.53 {mu}m of 5.8 dB/cm has been measured with a pump power of 65 mW at 980 nm.

An empirical spectroscopic database for acetylene in the regions of 5850-6341 cm-1 and 7000-9415 cm-1

Science.gov (United States)

Lyulin, O. M.; Campargue, A.

2017-12-01

Six studies have been recently devoted to a systematic analysis of the high-resolution near infrared absorption spectrum of acetylene recorded by Cavity Ring Down spectroscopy (CRDS) in Grenoble and by Fourier-transform spectroscopy (FTS) in Brussels and Hefei. On the basis of these works, in the present contribution, we construct an empirical database for acetylene in the 5850-9415 cm-1 region excluding the 6341-7000 cm-1 interval corresponding to the very strong ν1+ν3 manifold. Our database gathers and extends information included in our CRDS and FTS studies. In particular, the intensities of about 1700 lines measured by CRDS in the 7244-7920 cm-1 region are reported for the first time together with those of several bands of 12C13CH2 present in natural isotopic abundance in the acetylene sample. The Herman-Wallis coefficients of most of the bands are derived from a fit of the measured intensity values. A recommended line list is provided with positions calculated using empirical spectroscopic parameters of the lower and upper energy vibrational levels and intensities calculated using the derived Herman-Wallis coefficients. This approach allows completing the experimental list by adding missing lines and improving poorly determined positions and intensities. As a result the constructed line list includes a total of 11113 transitions belonging to 150 bands of 12C2H2 and 29 bands of 12C13CH2. For comparison the HITRAN database in the same region includes 869 transitions of 14 bands, all belonging to 12C2H2. Our weakest lines have an intensity on the order of 10-29 cm/molecule, about three orders of magnitude smaller than the HITRAN intensity cut off. Line profile parameters are added to the line list which is provided in HITRAN format. The comparison of the acetylene database to the HITRAN2012 line list or to results obtained using the global effective operator approach is discussed in terms of completeness and accuracy.

Energy gains from lattice-enabled nuclear reactions

International Nuclear Information System (INIS)

Nagel, David J.

2015-01-01

The energy gain of a system is defined as the ratio of its output energy divided by the energy provided to operate the system. Most familiar systems have energy gains less than one due to various inefficiencies. By contrast, lattice-enabled nuclear reactions (LENR) offer high energy gains. Theoretical values in excess of 1000 are possible. Energy gains over 100 have already been reported. But, they have not yet been sustained for commercially significant durations. This article summarizes the current status of LENR energy gains. (author)

Charge Gain, Voltage Gain, and Node Capacitance of the SAPHIRA Detector Pixel by Pixel

Science.gov (United States)

Pastrana, Izabella M.; Hall, Donald N. B.; Baker, Ian M.; Jacobson, Shane M.; Goebel, Sean B.

2018-01-01

The University of Hawai`i Institute for Astronomy has partnered with Leonardo (formerly Selex) in the development of HgCdTe linear mode avalanche photodiode (L-APD) SAPHIRA detectors. The SAPHIRA (Selex Avalanche Photodiode High-speed Infra-Red Array) is ideally suited for photon-starved astronomical observations, particularly near infrared (NIR) adaptive optics (AO) wave-front sensing. I have measured the stability, and linearity with current, of a 1.7-um (10% spectral bandpass) infrared light emitting diode (IR LED) used to illuminate the SAPHIRA and have then utilized this source to determine the charge gain (in e-/ADU), voltage gain (in uV/ADU), and node capacitance (in fF) for each pixel of the 320x256@24um SAPHIRA. These have previously only been averages over some sub-array. Determined from the ratio of the temporal averaged signal level to variance under constant 1.7-um LED illumination, I present the charge gain pixel-by-pixel in a 64x64 sub-array at the center of the active area of the SAPHIRA (analyzed separately as four 32x32 sub-arrays) to be about 1.6 e-/ADU (σ=0.5 e-/ADU). Additionally, the standard technique of varying the pixel reset voltage (PRV) in 10 mV increments and recording output frames for the same 64x64 subarray found the voltage gain per pixel to be about 11.7 uV/ADU (σ=0.2 uV/ADU). Finally, node capacitance was found to be approximately 23 fF (σ=6 fF) utilizing the aforementioned charge and voltage gain measurements. I further discuss the linearity measurements of the 1.7-um LED used in the charge gain characterization procedure.

Above-threshold structure in {sup 244}Cm neutron-induced fission cross section

Energy Technology Data Exchange (ETDEWEB)

Maslov, V.M. [Radiation Physics and Chemistry Problems Inst., Minsk-Sosny (Belarus)

1997-03-01

The quasi-resonance structure appearing above the fission threshold in neutron-induced fission cross section of {sup 244}Cm(n,f) is interpreted. It is shown to be due to excitation of few-quasiparticle states in fissioning {sup 245}Cm and residual {sup 244}Cm nuclides. The estimate of quasiparticle excitation thresholds in fissioning nuclide {sup 245}Cm is consistent with pairing gap and fission barrier parameters. (author)

Current gain above 10 in sub-10 nm base III-Nitride tunneling hot electron transistors with GaN/AlN emitter

Energy Technology Data Exchange (ETDEWEB)

Yang, Zhichao, E-mail: zcyang.phys@gmail.com; Zhang, Yuewei; Krishnamoorthy, Sriram; Nath, Digbijoy N. [Department of Electrical and Computer Engineering, The Ohio State University, Columbus, Ohio 43210 (United States); Khurgin, Jacob B. [Department of Electrical and Computer Engineering, Johns Hopkins University, Baltimore, Maryland 21218 (United States); Rajan, Siddharth [Department of Electrical and Computer Engineering, The Ohio State University, Columbus, Ohio 43210 (United States); Department of Materials Science and Engineering, The Ohio State University, Columbus, Ohio 43210 (United States)

2016-05-09

We report on a tunneling hot electron transistor amplifier with common-emitter current gain greater than 10 at a collector current density in excess of 40 kA/cm{sup 2}. The use of a wide-bandgap GaN/AlN (111 nm/2.5 nm) emitter was found to greatly improve injection efficiency of the emitter and reduce cold electron leakage. With an ultra-thin (8 nm) base, 93% of the injected hot electrons were collected, enabling a common-emitter current gain up to 14.5. This work improves understanding of the quasi-ballistic hot electron transport and may impact the development of high speed devices based on unipolar hot electron transport.