WorldWideScience

Sample records for closed die forging

  1. Medium carbon vanadium steels for closed die forging

    International Nuclear Information System (INIS)

    Jeszensky, Gabor; Plaut, Ronald Lesley

    1993-01-01

    This work analyses the medium carbon micro alloyed vanadium potential for closed die forged production. The steels reach the mechanical resistance requests during cooling after forging, eliminating the subsequent thermal treatment. Those steels also present good fatigue resistance and machinability. The industrial scale experiments are also reported

  2. Forging loads, deformation modes and fracture in axi-symmetrric closed die cold forging of sintered aluminium powder compacts

    International Nuclear Information System (INIS)

    Butt, M.A.; Ali, L.

    2003-01-01

    An experimental investigation into closed-die cold forging of sintered aluminium powder rod- shaped compacts was carried out. Axi-symmetric components were forged from sintered powder preforms with different initial diameter to height ratios. Different compaction pressures, sintering and lubrication conditions were used as variables during the investigations. Detailed observations were made on green/sintered density, compaction defects, forging loads, deformation modes and on the onset of fracture during progressive forging of sintered powder compacts. Experimental results obtained during the investigations have been presented and discussed in detail. (author)

  3. Void consolidation during open-die forging for ultralarge rotor shafts. (1. Formulation of void-closing behavior)

    International Nuclear Information System (INIS)

    Ono, Shin-ichi; Minami, Katsuyuki; Ochiai, Tomoyuki; Iwadate, Tadao; Nakata, Shin-ichi.

    1995-01-01

    Open-die forging experiments using different die geometries under hot isothermal conditions and three-dimensional simulations using rigid-plastic finite-element method were performed to formulate a void-closing behavior using only two factors; the integral of hydrostatic stress and the equivalent strain. First, upsetting, side-upsetting and V-shape die cogging of several cylinders with a spherical void at the center are carried out and the information on the void volume reduction is obtained. Seconds, the same forgings, but without voids is treated numerically and the development of stress and strain at the location of voids is investigated. Then, by combining these results, and using regression analysis, it is found that the void volume reduction is expressed as a polynomial function of the two factors. When the polynomial function is used, various forging methods can be evaluated quantitatively in terms of void-closing behavior. Therefore it is beneficial to optimize the forging process for a large rotor shaft. (author)

  4. The Simulation and Analysis of the Closed Die Hot Forging Process by A Computer Simulation Method

    Directory of Open Access Journals (Sweden)

    Dipakkumar Gohil

    2012-06-01

    Full Text Available The objective of this research work is to study the variation of various parameters such as stress, strain, temperature, force, etc. during the closed die hot forging process. A computer simulation modeling approach has been adopted to transform the theoretical aspects in to a computer algorithm which would be used to simulate and analyze the closed die hot forging process. For the purpose of process study, the entire deformation process has been divided in to finite number of steps appropriately and then the output values have been computed at each deformation step. The results of simulation have been graphically represented and suitable corrective measures are also recommended, if the simulation results do not agree with the theoretical values. This computer simulation approach would significantly improve the productivity and reduce the energy consumption of the overall process for the components which are manufactured by the closed die forging process and contribute towards the efforts in reducing the global warming.

  5. Reparation of damaged forging dies

    Directory of Open Access Journals (Sweden)

    Vukić Lazić

    2015-03-01

    Full Text Available The forging dies are in exploitation exposed to elevated temperatures and variable impact loads, both compressive and shear. Steels for manufacturing of these tools must endure those loads while maintaining mechanical properties and being resistant to wear and thermal fatigue. For those reasons, the alloyed steels are used for making the forging dies, though they have less weldability, because alloying increases proneness to hardening. Any reparatory hard facing (HF of the damaged dies would require the specially adjusted technology to the particular piece. In this paper reparatory hard facing of dies used for forging pieces in the automobile industry is considered. Prior to reparatory hard facing of the real tools, numerous experimental hard facings on models were performed. All the model hard facings were done on the same steels which were used for production of the real forging dies. To define the optimal hard facing technology one needs to derive the optimal combination of the adequate heat treatment(s, to select the proper filler metals and the welding procedure. The established optimal HF technology was applied to real forging dies whose service life was further monitored in conditions of exploitation

  6. Medium carbon vanadium steels for closed die forging; Acos de medio carbono microligados ao vanadio para forjaria em matriz fechada

    Energy Technology Data Exchange (ETDEWEB)

    Jeszensky, Gabor; Plaut, Ronald Lesley

    1994-12-31

    This work analyses the medium carbon micro alloyed vanadium potential for closed die forged production. The steels reach the mechanical resistance requests during cooling after forging, eliminating the subsequent thermal treatment. Those steels also present good fatigue resistance and machinability. The industrial scale experiments are also reported 16 refs., 21 figs.

  7. Analysis of Filling and Stresses in the Hot Forging Process Depending on Flange Die Shapes

    International Nuclear Information System (INIS)

    Kim, Jun Hyoung; Kim, Cheol

    2010-01-01

    Hot closed-forging process and the die used for forming an automotive flange were analyzed from the viewpoints of heat transfer, grain-flow lines, and stresses to obtain a forged product without defects such as surface cracks, laps, cold shots, and partial filling. The forging process including up-set, pre-forging, final forging and pressing forces was investigated using finite element analysis. The influence of the preform die and the ratio of the heights of the upper die to lower die on the forging process and die were investigated and a die shape (10 .deg. for the preform die, and 1.5:1 ratio for the final die) suitable to achieve successful forging was determined on the basis of a parametric study. All parametric design requirements such as strength, full filling, and a load limit of 13,000 KN were satisfied for this newly developed flange die. New dies and flanges were fabricated and investigated. Defects such as partial filling and surface cracks were not observed

  8. Computer Οptimization of Geometric Form of Tool and Preform for Closed-die Forging of Compressor Blade Simulator

    Directory of Open Access Journals (Sweden)

    A. V. Botkin

    2014-07-01

    Full Text Available Using the software package DEFORM 3D when developing technology of isothermal forging workpiece blades it is possible to reduce the pre-production time, to improve the quality of forgings and increase lifetime of forging dies. Computer modeling allows to predict the formation of such defects during forging as notches and wrinkles, underfilling of die impression, to estimate tool loads. Preform shape and angular position of the blade simulator were optimized in order to minimize the lateral forces generated during the forging operation.

  9. Investigating the effect of variable gutter technique as a novel method on vertical flow of material in closed die forging processes

    Energy Technology Data Exchange (ETDEWEB)

    Pourbashiri, M.; Sedighi, M. [Iran University, Tehran (Iran, Islamic Republic of)

    2016-04-15

    Recently, Variable gutter technique has been introduced as a novel method in order to reduce waste materials in closed-die forging processes. In this paper, the capability of this method is investigated for a family of forged parts that the vertical flow of material is the last stage of forming process. As a case study, using the variable gutter technique, the amount of waste material is decreased about 50% for a sample forged part with a local rising. The results of FVM simulations and experiments confirmed the effectiveness of the variable gutter technique in such forging processes. The vertical flow of material in the die cavity (h parameter), as a criterion, for different gutter width and thickness dimensions was examined by FVM simulations. The results shown that the gutter thickness has more effect on vertical flow of material than the gutter width. By decreasing the gutter thickness and increasing the gutter width, the amount of vertical flow of material is increased about 120% and 29%, respectively. Finally, A/H ratio (A = Max width of sectional area of a forged part, H = Max height of a forged part) is proposed as shape complexity factor of a forged part. The results of FVM simulations are indicated that for the ratio of A/H > 2, the variable gutter thickness technique is more effective and can be successfully used to reduce the amount of waste materials.

  10. Close toleranoe forging of chromium steel blades for powerful steam turbines

    International Nuclear Information System (INIS)

    Shastin, Eh.G.; Kositskij, Yu.N.; Lyubchits, G.A.

    1989-01-01

    Work on simulating technological process on die-forging hammer was performed in order to reduce the preparation period bringing technology of close tolerance forging of turbine blades to a commercial level. A special attention was paid to development of accurate forming of forgings of 20Kh13Sh, 12Kh13 and 15Kh11MFSh steels on screw presses with nominal effort equal to 80 and 144 MN

  11. Numerical optimization of die geometry in open die forging

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    This paper deals with numerical optimization of open die forging of large metallic ingots made by casting implying risk of defects, e.g. central pores. Different material hardening properties and die geometries are combined in order to investigate, which geometry gives rise to maximum closure...

  12. Physical modeling and numerical simulation of V-die forging ingot with central void

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2014-01-01

    Numerical simulation and physical modeling performed on small-scale ingots made from pure lead, having a hole drilled through their centerline to mimic porosity, are utilized to characterize the deformation mechanics of a single open die forging compression stage and to identify the influence...... of the lower V-die angle on porosity closure and forging load requirements of large cast ingots. Results show that a lower V-die angle of 120 provides the best closure of centerline porosity without demanding the highest forging loads or developing unreasonably asymmetric shapes that may create difficulties...... in multi-stage open die forging procedures....

  13. Design and Analysis of a Forging Die for Manufacturing of Multiple Connecting Rods

    Science.gov (United States)

    Megharaj, C. E.; Nagaraj, P. M.; Jeelan Pasha, K.

    2016-09-01

    This paper demonstrates to utilize the hammer capacity by modifying the die design such that forging hammer can manufacture more than one connecting rod in a given forging cycle time. To modify the die design study is carried out to understand the parameters that are required for forging die design. By considering these parameters, forging die is designed using design modelling tool solid edge. This new design now can produce two connecting rods in same capacity hammer. The new design is required to validate by verifying complete filing of metal in die cavities without any defects in it. To verify this, analysis tool DEFORM 3D is used in this project. Before start of validation process it is require to convert 3D generated models in to. STL file format to import the models into the analysis tool DEFORM 3D. After importing these designs they are analysed for material flow into the cavities and energy required to produce two connecting rods in new forging die design. It is found that the forging die design is proper without any defects and also energy graph shows that the forging energy required to produce two connecting rods is within the limit of that hammer capacity. Implementation of this project increases the production of connecting rods by 200% in less than previous cycle time.

  14. First Results of Energy Saving at Process Redesign of Die Forging Al-Alloys

    International Nuclear Information System (INIS)

    Pepelnjak, Tomaz; Kuzman, Karl; Kokol, Anton

    2011-01-01

    The contribution deals with eco-friendly solutions for shortened production chains of forging light alloys. During the die forging operations a remarkable amount of material goes into the flash and later on into chips during finish machining. These low value side products are rich with embedded energy therefore recycling or reprocessing could be very energy saving procedure.In cooperation with a die forging company a shortened reprocessing cycle has been studied starting from re-melting the forging flash and without additional heating to cast preforms for subsequent die forging. As such preforms have not as good formability characteristics as those done from extruded billets the isothermal forging process has been adopted. First results showed that without cracks and other defects the formability is sufficient for a broad spectrum of forgings.To improve the formability a homogenization process of cast preforms has been implemented. As the process started immediately after casting, amount of additional energy for heating was minimized. To reduce voids forging process was redesigned in a way to assure greater hydrostatic pressures in parts during forging. First results were promising therefore research is going towards improving processes without adding significantly more energy as it is needed for casting with homogenization and die forging.

  15. Structural changes of radial forging die surface during service under thermo-mechanical fatigue

    International Nuclear Information System (INIS)

    Nematzadeh, Fardin; Akbarpour, Mohammad Reza; Kokabi, Amir Hosein; Sadrnezhaad, Seyed Khatiboleslam

    2009-01-01

    Radial forging is one of the modern open die forging techniques and has a wide application in producing machine parts. During operation at high temperatures, severe temperature change associated with mechanical loads and the resultant wearing of the die surface lead to intense variation in strain on the die surface. Therefore, under this operating condition, thermo-mechanical fatigue (TMF) occurs on the surface of the radial forging die. TMF decreases the life of the die severely. In the present research, different layers were deposited on a 1.2714 steel die by SMAW and GTAW, with a weld wire of UDIMET 520. The microstructure of the radial forging die surface was investigated during welding and service using an optical microscope and scanning electron microscope. The results revealed that, after welding, the structure of the radial forging die surface includes the γ matrix with a homogeneous distribution of fine semi-spherical carbides. The weld structure consisted mostly of columnar dendrites with low grain boundaries. Also, microstructural investigation of the die surface during operation showed that the weld structure of the die surface has remained without any considerable change. Only dendrites were deformed and broken. Moreover, grain boundaries of the dendrites were revealed during service.

  16. Fatigue in cold-forging dies: Tool life analysis

    DEFF Research Database (Denmark)

    Skov-Hansen, P.; Bay, Niels; Grønbæk, J.

    1999-01-01

    In the present investigation it is shown how the tool life of heavily loaded cold-forging dies can be predicted. Low-cycle fatigue and fatigue crack growth testing of the tool materials are used in combination with finite element modelling to obtain predictions of tool lives. In the models...... the number of forming cycles is calculated first to crack initiation and then during crack growth to fatal failure. An investigation of a critical die insert in an industrial cold-forging tool as regards the influence of notch radius, the amount and method of pre-stressing and the selected tool material...

  17. Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

    International Nuclear Information System (INIS)

    Kwon, Yong Chul; Kang, Jong Hun; Kim, Sang Sik

    2016-01-01

    The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts

  18. Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Yong Chul [Gyeongnam Technopark, Changwon (Korea, Republic of); Kang, Jong Hun [Jungwon Univ., Goisan (Korea, Republic of); Kim, Sang Sik [Gyeongsang Natiional Univ., Jinju (Korea, Republic of)

    2016-02-15

    The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts.

  19. Brittle Fracture Behaviors of Large Die Holders Used in Hot Die Forging

    Directory of Open Access Journals (Sweden)

    Weifang Zhang

    2017-05-01

    Full Text Available Brittle fracture of large forging equipment usually leads to catastrophic consequences. To avoid this kind of accident, the brittle fracture behaviors of a large die holder were studied by simulating the practical application. The die holder is used on the large die forging press, and it is made of 55NiCrMoV7 hot-work tool steel. Detailed investigations including mechanical properties analysis, metallographic observation, fractography, transmission electron microscope (TEM analysis and selected area electron diffraction (SAED were conducted. The results reveal that the material generated a large quantity of large size polyhedral M23C6 (M: Fe and Cr mainly and elongated M3C (M: Fe mainly carbides along the martensitic lath boundaries when the die holder was recurrently tempered and water-cooled at 250 °C during the service. The large size carbides lead to the material embrittlement and impact toughness degradation, and further resulted in the brittle fracture of the die holder. Therefore, the operation specification must be emphasized to avoid the die holder being cooled by using water, which is aimed at accelerating the cooling.

  20. Precision forging technology for aluminum alloy

    Science.gov (United States)

    Deng, Lei; Wang, Xinyun; Jin, Junsong; Xia, Juchen

    2018-03-01

    Aluminum alloy is a preferred metal material for lightweight part manufacturing in aerospace, automobile, and weapon industries due to its good physical properties, such as low density, high specific strength, and good corrosion resistance. However, during forging processes, underfilling, folding, broken streamline, crack, coarse grain, and other macro- or microdefects are easily generated because of the deformation characteristics of aluminum alloys, including narrow forgeable temperature region, fast heat dissipation to dies, strong adhesion, high strain rate sensitivity, and large flow resistance. Thus, it is seriously restricted for the forged part to obtain precision shape and enhanced property. In this paper, progresses in precision forging technologies of aluminum alloy parts were reviewed. Several advanced precision forging technologies have been developed, including closed die forging, isothermal die forging, local loading forging, metal flow forging with relief cavity, auxiliary force or vibration loading, casting-forging hybrid forming, and stamping-forging hybrid forming. High-precision aluminum alloy parts can be realized by controlling the forging processes and parameters or combining precision forging technologies with other forming technologies. The development of these technologies is beneficial to promote the application of aluminum alloys in manufacturing of lightweight parts.

  1. Using of material-technological modelling for designing production of closed die forgings

    Science.gov (United States)

    Ibrahim, K.; Vorel, I.; Jeníček, Š.; Káňa, J.; Aišman, D.; Kotěšovec, V.

    2017-02-01

    Production of forgings is a complex and demanding process which consists of a number of forging operations and, in many cases, includes post-forge heat treatment. An optimized manufacturing line is a prerequisite for obtaining prime-quality products which in turn are essential to profitable operation of a forging company. Problems may, however, arise from modifications to the manufacturing route due to changing customer needs. As a result, the production may have to be suspended temporarily to enable changeover and optimization. Using material-technological modelling, the required modifications can be tested and optimized under laboratory conditions outside the plant without disrupting the production. Thanks to material-technological modelling, the process parameters can be varied rapidly in response to changes in market requirements. Outcomes of the modelling runs include optimum parameters for the forging part’s manufacturing route, values of mechanical properties, and results of microstructure analysis. This article describes the use of material-technological modelling for exploring the impact of the amount of deformation and the rate of cooling of a particular forged part from the finish-forging temperature on its microstructure and related mechanical properties.

  2. Open die forging of large shafts with porosity defects – physical and numerical modelling

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V-shaped d......The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V......-shaped dies with 90o and 120o and a reference pair of flat parallel platens. Holes drilled through the center of these preforms are produced to mimic centerline porosity in full scale cast ingots and intermediate rotation of the preforms replicate a multi-stage forging sequence under laboratory testing...

  3. Recent technological developments in forging; Recentes avancos tecnologicos no forjamento

    Energy Technology Data Exchange (ETDEWEB)

    Schaeffer, Lirio [Rio Grande do Sul Univ., Porto Alegre, RS (Brazil). Programa de Pos-graduacao em Engenharia Metalurgica e dos Materiais

    1987-12-31

    Recent advances in the area of open and closed die forging are summarized and discussed. The use of computer and alternatives such as incremental forging, sinter forging, liquid forging and precision forging are the main items reviewed 11 refs., 10 figs.

  4. Properties of powder metallurgy steel forgings

    International Nuclear Information System (INIS)

    Crowson, A.; Anderson, F.E.

    1977-01-01

    The effects of processing variables on the mechanical properties of heat-treated powder metallurgy (P/M) steel forgings were determined. Prealloyed 4600 steel powder blended with graphite to yield 4640 was compacted into preforms and hot forged in a warm, closed die. Variables studied were preform density, method of lubrication, preform sintering (time, temperature and atmosphere), forging pressure (20 and 40 tsi) and temperature (1850 0 F, 2000 0 F and 2200 0 F), and forging ratio (0.75 and 0.95). Relationships between interconnected porosity and total porosity for the various preform densities were determined. High density compacts required higher sintering temperatures due to the restricted mobility of the reducing gases in the pores. Die wall lubrication was comparable to admixed lubrication, and it simplified powder mixing and preform sintering operations. Forgings with densities from 99 to 99.8 percent of theoretical density were attained with a forging pressure of 20 to 40 tsi and preform temperatures of 2000 0 F and above. At forging conditions which resulted in forgings with acceptable mechanical properties, complete die fill was accomplished at a forging ratio of 0.95, whereas incomplete die fill resulted at a forging ratio of 0.75. The response of P/M forgings to heat treatment was comparable to that for wrought materials, and the resultant tensile and yield strengths were equivalent to the strength values described for wrought 4640 steel in AMS specification 6317B. In addition, ductility and impact properties of P/M forgings with near theoretical density (99.5+ percent) were comparable to bar stock forgings

  5. The influence of main parameters of the process of forging on the initial quality of forging for steel 35HM

    International Nuclear Information System (INIS)

    Banaszek, G.; Dyja, H.; Berski, S.

    2001-01-01

    The article discuss the effect of the main forging parameters and the selection of tools on improving the internal quality of forgings and closing up discontinuities of metallurgical origin during forging. As a result of investigations, the optimal values of the main technological parameters of forging have been determined and the application of an appropriate group of tools have been proposed for the flat die forging of forgings. (author)

  6. Multi-objective optimization of die geometry in ingot forging

    DEFF Research Database (Denmark)

    Christiansen, Peter; Martins, Paulo A.F.; Bay, Niels

    2014-01-01

    The soundness of an ingot after hot forging with different V-shaped lower dies is evaluated using finite element simulations.Two different modelling approaches that make use of uncoupled ductile damage and coupled ductile damage based on porousplasticity are employed. It is shown that the two...

  7. Lubricant influence on the ejection and roughness of in-die electro sinter forged Ti-discs

    DEFF Research Database (Denmark)

    Cannella, Emanuele; Nielsen, Chris Valentin

    2018-01-01

    Electro Sinter Forging (ESF) is a new sintering process based on Joule heating by high electrical current flowing through compacted metal powder under mechanical pressure. The whole process takes about three seconds and is based on a closed-die setup, where the sample is sintered inside a die....... A near-net shape component is therefore manufactured. One of the challenges associated with this process is the ejection of the sample after sintering. Due to powder compaction and axial loading during sintering, a radial pressure is generated at the die/sample interface. Consequently, the ejection can...... of commercially pure titanium powder. The force was measured while ejecting the samples by using a speed-controlled press. The surface roughness parameter Sa was measured by using a laser confocal microscope....

  8. Wear Analysis of Die Inserts in the Hot Forging Process of a Forked Type Forging Using Reverse Scanning Techniques

    Directory of Open Access Journals (Sweden)

    Łukasz Dworzak

    2017-12-01

    Full Text Available This article presents a wear analysis of die inserts used in the hot forging process of a forked forging (yoke, an element applied in steering systems of passenger vehicles. Studies involved the application of an original reverse scanning method intended for rapid and reliable wear analysis of forging tools (with complicated shape affording easy assessment without the need to dismount tools from the forging unit. The developed method involves analysis of progressive wear of forging tools based on measurements (scanning of forgings periodically collected from the process and constitutes a useful tool for measurement and testing. As the authors’ earlier works have demonstrated, the proposed new approach to analysis of tool wear with the application of reverse 3D scanning has proven successful in multiple instances in the case of axially symmetrical objects. The presented results of studies indicate that it is possible to utilize the expanded method to analyze the lifetime of forging tools, including tools with complex geometry. Application of the reverse scanning method allows for continuous and practical monitoring of the condition of forging tools over the course of the forging process and should have a positive impact on improving production output and reducing production costs.

  9. Multi-objective optimization of swash plate forging process parameters for the die wear/service life improvement

    Science.gov (United States)

    Hu, X. F.; Wang, L. G.; Wu, H.; Liu, S. S.

    2017-12-01

    For the forging process of the swash plate, the author designed a kind of multi-index orthogonal experiment. Based on the Archard wear model, the influences of billet temperature, die temperature, forming speed, top die hardness and friction coefficient on forming load and die wear were numerically simulated by DEFORM software. Through the analysis of experimental results, the best forging process parameters were optimized and determined, which could effectively reduce the die wear and prolong the die service life. It is significant to increase the practical production of enterprise, especially to reduce the production cost and to promote enterprise profit.

  10. Increasing of the lifetime of large forging dies by repairwelding

    Science.gov (United States)

    Duchek, M.; Koukolikova, M.; Kotous, J.; Majer, M.

    2018-02-01

    Repair welding is often used for rebuilding discarded or failed forging dies. It saves the cost of new tools. Increased useful life of repaired dies is another motivation for repair welding. This article focuses on the development of new filler materials for this purpose. The main goal was to prolong the life of tools of DIN 1.2714 material. Filler wires of two chemistries were made and several samples were experimentally welded. Metallographic and tribological analyses were carried out.

  11. Investigation of the influence of hybrid layers on the life time of hot forging dies

    Directory of Open Access Journals (Sweden)

    S. Legutko

    2013-04-01

    Full Text Available The paper deals with the issues related in the process of drop forging with special attention paid to the durability of forging tools. It presents the results of industrial investigation of the influence of hybrid layers on hot forging dies. The effectiveness of hybrid layers type nitrided layer/PVD coating applied for extending the life of forging tools whose working surfaces are exposed to such complex exploitation conditions as, among others, cyclically varying high thermal and mechanical loads, as well as intensive abrasion at raised temperature. The examination has been performed on a set of forging tools made of Unimax steel and intended for forging steel rings of gear box synchronizer in the factory FAS in Swarzedz (Poland.

  12. Optimum back-pressure forging using servo die cushion

    OpenAIRE

    Kawamoto, Kiichiro; Yoneyama, Takeshi; Okada, Masato; Kitayama, Satoshi; Chikahisa, Junpei

    2014-01-01

    This study focused on utilizing a servo die cushion (in conjunction with a servo press) as a "back-pressure load generator," to determine its effect on shape accuracy of the formed part and total forming load in forward extrusion during cold forging. The effect of back-pressure load application was confirmed in experiments, and the optimum setting pattern of back-pressure load was considered to minimize both shape accuracy of the formed part and back-pressure energy, which was representative ...

  13. The Investigations of Friction under Die Surface Vibration in Cold Forging Process

    DEFF Research Database (Denmark)

    Jinming, Sha

    investigation, and the second stage is to design and manufacture a more practical tool system which can be used to forging some industrial components with larger capacity. The high performance and power piezoelectric actuator stack as the vibration source will be used for designing the vibration system in order...... to 50% with vibration being applied in forming process. Furthermore, by using finite element method, a series of the simulations of the cold forging process under die surface excitation have been implemented in order to further understand the influence of vibration on friction, especially the influence...

  14. The Influence of Temperature on the Frictional Behavior of Duplex-Coated Die Steel Rubbing Against Forging Brass

    Science.gov (United States)

    Ebrahimzadeh, I.; Ashrafizadeh, F.

    2015-01-01

    Improvement of die life under hot forging of brass alloys is considered vital from both economical and technical points of view. One of the best methods for improving die life is duplex coatings. In this research, the influence of temperature on the tribological behavior of duplex-coated die steel rubbing against forging brass was investigated. The wear tests were performed on a pin-on-disk machine from room temperature to 700 °C; the pins were made in H13 hot work tool steel treated by plasma nitriding and by PVD coatings of TiN-TiAlN-CrAlN. The disks were machined from a two-phase brass alloy too. The results revealed that the friction coefficient of this tribosystem went through a maximum at 550 °C and decreased largely at 700 °C. Furthermore, the formation of Cr2O3 caused the reduction of friction coefficient at 700 °C. PVD coatings proved their wear resistance up to 550 °C, well above the working temperature of the brass forging dies.

  15. Comparison study of multistep forging and injection forging of automobile fasteners

    OpenAIRE

    Chen Senyong; Qin Yi

    2015-01-01

    In order to improve production efficiency, injection forging as a feasible approach was introduced to automobile fasteners production. In the study reported in this paper, two forging approaches, traditional multistep forging and injection forging, were analysed by using a finite element method. Using ABAQUS and DEFORM, some significant factors, namely, forging force, energy consumption, component accuracy and stress distribution in the die, were compared to explore the potential and challeng...

  16. A study on die wear model of warm and hot forgings

    Science.gov (United States)

    Kang, J. H.; Park, I. W.; Jae, J. S.; Kang, S. S.

    1998-05-01

    Factors influencing service lives of tools in warm and hot forging processes are wear, mechanical fatigue, plastic deformation and thermal fatigue, etc. Wear is the predominant factor for tool failure among these. To predict tool life by wear, Archard's model where hardness is considered as constant or function of temperature is generally applied. Usually hardness of die is a function of not only temperature but operating time of die. To consider softening of die by repeated operation it is necessary to express hardness of die by a function of temperature and time. In this study wear coefficients were measured for various temperatures and heat treatment for H13 tool steel. Also by experiment of reheating of die, die softening curves were obtained. From experimental results, relationships between tempering parameters and hardness were established to investigate effects of hardness decrease by the effect of temperatures and time. Finally modified Archard's wear model in which hardness is considered to be a function of main tempering curve was proposed. And finite element analyses were conducted by adopting suggested wear model. By comparisons of simulations and real profiles of worn die, proposed wear model was verified.

  17. Selection of the optimal hard facing (HF technology of damaged forging dies based on cooling time t8/5

    Directory of Open Access Journals (Sweden)

    D. Arsić

    2016-01-01

    Full Text Available In exploitation, the forging dies are exposed to heating up to very high temperatures, variable loads: compressive, impact and shear. In this paper, the reparatory hard facing of the damaged forging dies is considered. The objective was to establish the optimal reparatory technology based on cooling time t8/5 . The verification of the adopted technology was done by investigation of the hard faced layers microstructure and measurements of hardness within the welded layers’ characteristic zones. Cooling time was determined theoretically, numerically and experimentally.

  18. Modelling of defects in ingot forging

    DEFF Research Database (Denmark)

    Christiansen, Peter

    The present report presents an investigation of the ingot forging process with special emphasis on modelling the influence of die geometry on the soundness of the ingot after hot forging. An investigation on how to model damage is also performed. The influence of the lower die angle is quantified...... angle of 130o-140o giving rise to the largest centreline porosity closure regardless of material hardening behaviour applied. Friction was found only to have minor influence on the optimum. Multi stroke forging operations have also been modelled since the ingot forging process consists of many forging...... damage. It is found that when evaluating damage only by relative density; feed size and lower die angle does not influence whether the hot forging process is successful or not. This is in disagreement with the general understanding of the ingot forging process. When evaluating ductile damage...

  19. Research on Oxidation Wear Behavior of a New Hot Forging Die Steel

    Science.gov (United States)

    Shi, Yuanji; Wu, Xiaochun

    2018-01-01

    Dry sliding tests for the hot forging die steel DM were performed in air under the test temperature at 400-700 °C and the time of 0.5-4 h by a UMT-3 high-temperature wear tester. The wear behavior and characteristics were studied systematically to explore the general characters in severe oxidation conditions. The results showed that a mild-to-severe oxidation wear transition occurred with an increase in the test temperature and duration. The reason was clarified as the unstable M6C carbides coarsening should be responsible for the severe delamination of tribo-oxide layer. More importantly, an intense oxidation wear with lower wear rates was found when the experimental temperature reaches 700 °C or after 4 h of test time at 600 °C, which was closely related to the degradation behavior during wear test. Furthermore, a new schematic diagram of oxidation wear of DM steel was proposed.

  20. Forging process design for risk reduction

    Science.gov (United States)

    Mao, Yongning

    In this dissertation, forging process design has been investigated with the primary concern on risk reduction. Different forged components have been studied, especially those ones that could cause catastrophic loss if failure occurs. As an effective modeling methodology, finite element analysis is applied extensively in this work. Three examples, titanium compressor disk, superalloy turbine disk, and titanium hip prosthesis, have been discussed to demonstrate this approach. Discrete defects such as hard alpha anomalies are known to cause disastrous failure if they are present in those stress critical components. In this research, hard-alpha inclusion movement during forging of titanium compressor disk is studied by finite element analysis. By combining the results from Finite Element Method (FEM), regression modeling and Monte Carlo simulation, it is shown that changing the forging path is able to mitigate the failure risk of the components during the service. The second example goes with a turbine disk made of superalloy IN 718. The effect of forging on microstructure is the main consideration in this study. Microstructure defines the as-forged disk properties. Considering specific forging conditions, preform has its own effect on the microstructure. Through a sensitivity study it is found that forging temperature and speed have significant influence on the microstructure. In order to choose the processing parameters to optimize the microstructure, the dependence of microstructure on die speed and temperature is thoroughly studied using design of numerical experiments. For various desired goals, optimal solutions are determined. The narrow processing window of titanium alloy makes the isothermal forging a preferred way to produce forged parts without forging defects. However, the cost of isothermal forging (dies at the same temperature as the workpiece) limits its wide application. In this research, it has been demonstrated that with proper process design, the die

  1. New Trends in Forging Technologies

    Science.gov (United States)

    Behrens, B.-A.; Hagen, T.; Knigge, J.; Elgaly, I.; Hadifi, T.; Bouguecha, A.

    2011-05-01

    Limited natural resources increase the demand on highly efficient machinery and transportation means. New energy-saving mobility concepts call for design optimisation through downsizing of components and choice of corrosion resistant materials possessing high strength to density ratios. Component downsizing can be performed either by constructive structural optimisation or by substituting heavy materials with lighter high-strength ones. In this context, forging plays an important role in manufacturing load-optimised structural components. At the Institute of Metal Forming and Metal-Forming Machines (IFUM) various innovative forging technologies have been developed. With regard to structural optimisation, different strategies for localised reinforcement of components were investigated. Locally induced strain hardening by means of cold forging under a superimposed hydrostatic pressure could be realised. In addition, controlled martensitic zones could be created through forming induced phase conversion in metastable austenitic steels. Other research focused on the replacement of heavy steel parts with high-strength nonferrous alloys or hybrid material compounds. Several forging processes of magnesium, aluminium and titanium alloys for different aeronautical and automotive applications were developed. The whole process chain from material characterisation via simulation-based process design to the production of the parts has been considered. The feasibility of forging complex shaped geometries using these alloys was confirmed. In spite of the difficulties encountered due to machine noise and high temperature, acoustic emission (AE) technique has been successfully applied for online monitoring of forging defects. New AE analysis algorithm has been developed, so that different signal patterns due to various events such as product/die cracking or die wear could be detected and classified. Further, the feasibility of the mentioned forging technologies was proven by means

  2. Die forging of the alloys Az80 and Zk60

    NARCIS (Netherlands)

    Kurz, G.; Clauw, B.; Sillekens, W.H.; Letzig, D.

    2009-01-01

    Overall goal of the MagForge project is to provide tailored and cost-effective technologies for the industrial manufacturing of magnesium forged components. Scientific and technological aspects are new alloys/feedstock materials with improved performance, forging process modeling and design tools

  3. Forging evaluaion of 304L stainless steel

    International Nuclear Information System (INIS)

    Packard, C.L.; Edstrom, C.M.

    1979-01-01

    The objective of this project was to evaluate and characterize the effects of various forging parameters on the metallographic structure and mechanical properties of 304L stainless steel forgings. Upset and die forgings were produced by hammer and Dynapak forging with forging temperatures ranging from 760 to 1145 0 C, upset reductions ranging from 20 to 60%, and annealing times ranging from 0 to 25 minutes at 843 0 C. The carbide precipitation behavior observed was found to be a function of forging temperature and annealing time. Higher forging temperatures were beneficial in avoiding continuous carbide precipitation and annealing at 843 0 C promoted increased carbide precipitation. The yield strength of the unannealed forgings decreased with increasing forging temperature and, with the exception of the 1145 0 C upset forgings, was significantly lowered by annealing

  4. Tool design and materials for electro sinter forging (ESF)

    DEFF Research Database (Denmark)

    Cannella, Emanuele; Nielsen, Chris Valentin

    ) process, the main requirement is the electrical current passing through the electrical conducting powder. To obtain this, a closed-die setup with electrical insulating properties was used. Furthermore, the alignment between the compacting punch and die needed to be ensured by pre-aligning or alternatively...... by using an alignment system. The present work is focused on the designing phase of a tool for the electro sinter forging of a disc, made from titanium powder. By applying a pre-alignment system, the setup resulted suitable for this application. A tool design for sintering rings is also showed....

  5. Qualitative Research of AZ31 Magnesium Alloy Aircraft Brackets Produced by a New Forging Method

    Directory of Open Access Journals (Sweden)

    Dziubińska A.

    2016-06-01

    Full Text Available The paper reports a selection of numerical and experimental results of a new closed-die forging method for producing AZ31 magnesium alloy aircraft brackets with one rib. The numerical modelling of the new forming process was performed by the finite element method.The distributions of stresses, strains, temperature and forces were examined. The numerical results confirmed that the forgings produced by the new forming method are correct. For this reason, the new forming process was verified experimentally. The experimental results showed good agreement with the numerical results. The produced forgings of AZ31 magnesium alloy aircraft brackets with one rib were then subjected to qualitative tests.

  6. Simulation and analysis of hot forging process for industrial locking gear elevators

    Science.gov (United States)

    Maarefdoust, M.; Kadkhodayan, M.

    2010-06-01

    In this paper hot forging process for industrial locking gear elevators is simulated and analyzed. An increase in demand of industrial locking gear elevators with better quality and lower price caused the machining process to be replaced by hot forging process. Production of industrial locking gear elevators by means of hot forging process is affected by many parameters such as billet temperature, geometry of die and geometry of pre-formatted billet. In this study the influences of billet temperature on effective plastic strain, radius of die corners on internal stress of billet and thickness of flash on required force of press are investigated by means of computer simulation. Three-dimensional modeling of initial material and die are performed by Solid Edge, while simulation and analysis of forging are performed by Super Forge. Based on the computer simulation the required dies are designed and the workpieces are formed. Comparison of simulation results with experimental data demonstrates great compatibility.

  7. Simulation and experimental verification of the filling process of semi-solid die forging for cup shell

    OpenAIRE

    Jianbo TAN; Zichao WANG; Dongxu WANG

    2015-01-01

    The filling mold process of semi-solid alloy blank influences severely the forming and properties of finished piece. In this paper, DEFORM is applied to simulate the process of cup-type 6061 alloy die forging casting. The influences of the temperature of semi-solid alloy blank, preheating temperature, and downward press speed of pressure head on process of mold filling and velocity field are investigated. The results show that the mold filling of semi-solid alloy paste smoothly fills along th...

  8. Studies of the quality and cost-effectiveness of a novel conceptof open-die forged powerplant main shaft

    Directory of Open Access Journals (Sweden)

    P. Skubisz

    2015-04-01

    Full Text Available An innovatory concept of open-die forging of windmill main shaft is described. Comparative study of the new technology based on the concept of cogging hollow shaft on mandrel featuring material savings and higher quality of a finished part versus traditional production chain of this component is presented, indicating benefits and technological setbacks of industrial implementation. Results of industrial sampling aided with numerical simulation form guidelines for technological realization.

  9. Adapted diffusion processes for effective forging dies

    Science.gov (United States)

    Paschke, H.; Nienhaus, A.; Brunotte, K.; Petersen, T.; Siegmund, M.; Lippold, L.; Weber, M.; Mejauschek, M.; Landgraf, P.; Braeuer, G.; Behrens, B.-A.; Lampke, T.

    2018-05-01

    Hot forging is an effective production method producing safety relevant parts with excellent mechanical properties. The economic efficiency directly depends on the occurring wear of the tools, which limits service lifetime. Several approaches of the presenting research group aim at minimizing the wear caused by interacting mechanical and thermal loads by using enhanced nitriding technology. Thus, by modifying the surface zone layer it is possible to create a resistance against thermal softening provoking plastic deformation and pronounced abrasive wear. As a disadvantage, intensely nitrided surfaces may possibly include the risk of increased crack sensitivity and therefore feature the chipping of material at the treated surface. Recent projects (evaluated in several industrial applications) show the high technological potential of adapted treatments: A first approach evaluated localized treatments by preventing areas from nitrogen diffusion with applied pastes or other coverages. Now, further ideas are to use this principle to structure the surface with differently designed patterns generating smaller ductile zones beneath nitrided ones. The selection of suitable designs is subject to certain geo-metrical requirements though. The intention of this approach is to prevent the formation and propagation of cracks under thermal shock conditions. Analytical characterization methods for crack sensitivity of surface zone layers and an accurate system of testing rigs for thermal shock conditions verified the treatment concepts. Additionally, serial forging tests using adapted testing geometries and finally, tests in the industrial production field were performed. Besides stabilizing the service lifetime and decreasing specific wear mechanisms caused by thermal influences, the crack behavior was influenced positively. This leads to a higher efficiency of the industrial production process and enables higher output in forging campaigns of industrial partners.

  10. Optimum design of forging process parameters and preform shape under uncertainties

    International Nuclear Information System (INIS)

    Repalle, Jalaja; Grandhi, Ramana V.

    2004-01-01

    Forging is a highly complex non-linear process that is vulnerable to various uncertainties, such as variations in billet geometry, die temperature, material properties, workpiece and forging equipment positional errors and process parameters. A combination of these uncertainties could induce heavy manufacturing losses through premature die failure, final part geometric distortion and production risk. Identifying the sources of uncertainties, quantifying and controlling them will reduce risk in the manufacturing environment, which will minimize the overall cost of production. In this paper, various uncertainties that affect forging tool life and preform design are identified, and their cumulative effect on the forging process is evaluated. Since the forging process simulation is computationally intensive, the response surface approach is used to reduce time by establishing a relationship between the system performance and the critical process design parameters. Variability in system performance due to randomness in the parameters is computed by applying Monte Carlo Simulations (MCS) on generated Response Surface Models (RSM). Finally, a Robust Methodology is developed to optimize forging process parameters and preform shape. The developed method is demonstrated by applying it to an axisymmetric H-cross section disk forging to improve the product quality and robustness

  11. Fractography analysis of tool samples used for cold forging

    DEFF Research Database (Denmark)

    Dahl, K.V.

    2002-01-01

    Three fractured tool dies used for industrial cold forging have been investigated using light optical microscopy and scanning electron microscopy. Two of the specimens were produced using the traditional Böhler P/M steel grade s790, while the lastspecimen was a third generation P/M steel produced...... using new technology developed by Böhler. All three steels have the same nominal composition of alloying elements. The failure in both types of material occurs as a crack formation at a notch inside ofthe tool. Generally the cold forging dies constructed in third generation steels have a longer lifetime...

  12. Deducing material quality in cast and hot-forged steels by new bending test

    Science.gov (United States)

    Valberg, Henry; Langøy, Morten; Nedreberg, Mette; Helvig, Torgeir

    2017-10-01

    A special bend test has been developed and applied for the purpose of characterization and comparison of the material ductility in crankpin steel discs manufactured by casting, or casting subsequently followed by hot open-die forging (ODF) or closed-die forging (CDF). The bending test specimen consists of a small rectangular plate of material with a round hole cut out in the middle. The "eye-shape" specimens were cut out from various positions either near to the surface of, or from the interior of the discs. The test method revealed differences in ductility for the investigated materials, and for different depth positions inside the discs. The roughening of the specimen surface on the top-side of the specimen bend also varied dependent on the processing method for the material. Current results show that this test method is useful for evaluation of material quality in differently processed material. Experimental bend test results are presented for differently processed variants of the same material, i.e., crankpin discs either made by solely casting or casting subsequently followed by hot working either by ODF or CDF.

  13. Manufacturing of Nanostructured Rings from Previously ECAE-Processed AA5083 Alloy by Isothermal Forging

    Directory of Open Access Journals (Sweden)

    C. J. Luis

    2013-01-01

    Full Text Available The manufacturing of a functional hollow mechanical element or ring of the AA5083 alloy previously equal channel angular extrusion (ECAE processed, which presents a submicrometric microstructure, is dealt with. For this purpose, the design of two isothermal forging dies (preform and final shape is carried out using the design of experiments (DOE methodology. Moreover, after manufacturing the dies and carrying out tests so as to achieve real rings, the mechanical properties of these rings are analysed as well as their microstructure. Furthermore, a comparison between the different forged rings is made from ECAE-processed material subjected to different heat treatments, previous to the forging stage. On the other hand, the ring forging process is modelled through the use of finite element simulation in order to improve the die design and to study the force required for the isothermal forging, the damage value, and the strain the material predeformed by ECAE has undergone. With this present research work, it is intended to improve the knowledge about the mechanical properties of nanostructured material and the applicability of this material to industrial processes that allow the manufacturing of functional parts.

  14. Precision die design by the die expansion method

    CERN Document Server

    Ibhadode, A O Akii

    2009-01-01

    This book presents a new method for the design of the precision dies used in cold-forging, extrusion and drawing processes. The method is based upon die expansion, and attempts to provide a clear-cut theoretical basis for the selection of critical die dimensions for this group of precision dies when the tolerance on product diameter (or thickness) is specified. It also presents a procedure for selecting the minimum-production-cost die from among a set of design alternatives. The mathematical content of the book is relatively simple and will present no difficulty to those who have taken basic c

  15. Forging technology for large nuclear pressure vessel parts

    International Nuclear Information System (INIS)

    Kakimoto, Hideki; Ikegami, Tomonori

    2014-01-01

    The increasing output of nuclear power generation calls for larger vessels for next-generation nuclear power plants. A vessel with an increased diameter requires increased load for its forging, which can make it difficult to use a conventional solid die. In order to reduce the forging load, a rotary incremental forging method has been applied to hot forging. This method includes pressing and rotating a material in an incremental manner such that a target shape is obtained. This study aimed at improving the accuracy of numerical simulation for the rotary incremental forging to reduce the load when forging large vessels. This has enabled the temperature of the material and flow stress to be precisely predicted; an example of this is reported in the paper. Specifically, the heat transfer coefficient to be used for the numerical simulation had been determined experimentally from a small-scale hot-forging. The reduction of the flow stress associated with incremental forging, had been deduced from a compression test, and the value was applied to the numerical simulation. A preform was designed on the basis of the above simulation to perform a 1/1 size scale experiment. A precision of better than 5% has been confirmed for the shape prediction. (author)

  16. Wear Improvement of Tools in the Cold Forging Process for Long Hex Flange Nuts.

    Science.gov (United States)

    Hsia, Shao-Yi; Shih, Po-Yueh

    2015-09-25

    Cold forging has played a critical role in fasteners and has been widely used in automotive production, manufacturing, aviation and 3C (Computer, Communication, and Consumer electronics). Despite its extensive use in fastener forming and die design, operator experience and trial and error make it subjective and unreliable owing to the difficulty of controlling the development schedule. This study used finite element analysis to establish and simulate wear in automotive repair fastener manufacturing dies based on actual process conditions. The places on a die that wore most quickly were forecast, with the stress levels obtained being substituted into the Archard equation to calculate die wear. A 19.87% improvement in wear optimization occurred by applying the Taguchi quality method to the new design. Additionally, a comparison of actual manufacturing data to simulations revealed a nut forging size error within 2%, thereby demonstrating the accuracy of this theoretical analysis. Finally, SEM micrographs of the worn surfaces on the upper punch indicate that the primary wear mechanism on the cold forging die for long hex flange nuts was adhesive wear. The results can simplify the development schedule, reduce the number of trials and further enhance production quality and die life.

  17. Hot forging of roll-cast high aluminum content magnesium alloys

    Science.gov (United States)

    Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

    2017-10-01

    This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

  18. Sintering and densification; new techniques: sinter forging

    International Nuclear Information System (INIS)

    Winnubst, A.J.A.

    1998-01-01

    In this chapter pressure assisted sintering methods will be described. Attention will mainly be paid to sinter forging as a die-wall free uniaxial pressure sintering technique, where large creep strains are possible. Sinter forging is an effective tool to reduce sintering temperature and time and to obtain a nearly theoretically dense ceramic. In this way grain size in tetragonal zirconia ceramics can be reduced down to 100 nm. Another important phenomenon is the reduction of the number density and size of cracks and flaws resulting in higher strength and improved reliability, which is of utmost importance for engineering ceramics. The creep deformation during sinter forging causes a rearrangement of the grains resulting in a reduction of interatomic spaces between grains, while grain boundary (glassy) phases can be removed. The toughness and in some cases the wear resistance is enhanced after sinter forging as a result of the grain-boundary-morphology improvement. (orig.)

  19. Design and Optimization of Die Preforming Process for Long Last-stage Blade of Nuclear Power

    Directory of Open Access Journals (Sweden)

    He Xiaomao

    2017-01-01

    Full Text Available The long last-stage blade is a key component of the steam turbine of nuclear conventional island. The die preforming process for a new technology that provides billets for near-net-shape roll-forging process was designed, the effects of the forging temperature, friction coefficient, flash land’s height and die’s outer fillet radius on the die forging force and forging energy were studied by using the orthogonal experiment method, the primary and secondary order of the four factors were analysed by using range analysis method, and the optimal combination of the factors was obtained. By means of numerical simulation and physical experiment, the die preforming process that can provide qualified billets for the subsequent roll-forging process was verified, and the PZS1120f electric screw press can meet the requirements of the die preforming process.

  20. Numerical modelling of damage evolution in ingot forging

    DEFF Research Database (Denmark)

    Christiansen, Peter; Martins, Paulo A.F.; Bay, Niels Oluf

    2015-01-01

    The ingot forging process is numerically simulated applying both the Shima-Oyane porous plasticity model as a coupled damage model and the uncoupled normalized Cockcroft & Latham criterion. Four different cases including two different lower die angles (120º and 180º) and two different sizes of feed...... (400mm and 800mm) are analysed. Comparison of the simulation results with recommendations in literature on ingot forging, indicates the normalized Cockcroft & Latham damage criterion to be the most realistic of the two....

  1. Analysis of reforming process of large distorted ring in final enlarging forging

    International Nuclear Information System (INIS)

    Miyazawa, Takeshi; Murai, Etsuo

    2002-01-01

    In the construction of reactors or pressure vessels for oil chemical plants and nuclear power stations, mono block open-die forging rings are often utilized. Generally, a large forged ring is manufactured by means of enlarging forging with reductions of the wall thickness. During the enlarging process the circular ring is often distorted and becomes an ellipse in shape. However the shape control of the ring is a complicated work. This phenomenon makes the matter still worse in forging of larger rings. In order to make precision forging of large rings, we have developed the forging method using a v-shape anvil. The v-shape anvil is geometrically adjusted to fit the distorted ring in the final circle and reform automatically the shape of the ring during enlarging forging. This paper has analyzed the reforming process of distorted ring by computer program based on F.E.M. and examined the effect on the precision of ring forging. (author)

  2. Optimising mechanical properties of hot forged nickel superalloy 625 components

    Science.gov (United States)

    Singo, Nthambe; Coles, John; Rosochowska, Malgorzata; Lalvani, Himanshu; Hernandez, Jose; Ion, William

    2018-05-01

    Hot forging and subsequent heat treatment were resulting in substandard mechanical properties of nickel superalloy, Alloy 625, components. The low strength was found to be due to inadequate deformation during forging, excessive grain growth and precipitation of carbides during subsequent heat treatment. Experimentation in a drop forging company and heat treatment facility led to the establishment of optimal parameters to minimise grain size and mitigate the adverse effects of carbide precipitation, leading to successful fulfilment of mechanical property specifications. This was achieved by reducing the number of operations, maximising the extent of deformation by changing the slug dimensions and its orientation in the die, and minimising the time of exposure to elevated temperatures in both the forging and subsequent heat treatment processes to avoid grain growth.

  3. Nano Precipitation and Hardening of Die-Quenched 6061 Aluminum Alloy.

    Science.gov (United States)

    Utsunomiya, Hiroshi; Tada, Koki; Matsumoto, Ryo; Watanabe, Katsumi; Matsuda, Kenji

    2018-03-01

    Die quenching is applied to an age-hardenable aluminium alloys to obtain super-saturated solid solution. The application is advantageous because it can reduce number of manufacturing processes, and may increase strength by strain aging. If die quenching is realized in forging as well as sheet forming, it may widen industrial applicability further. In this study, Al-Mg-Si alloy AA6061 8 mm-thick billets were reduced 50% in height without cracks by die-quench forging. Supersaturated solid solution was successfully obtained. The die-quenched specimen shows higher hardness with nano precipitates at shorter aging time than the conventional water-quenched specimen.

  4. Effect of Friction on Barreling during cold Upset Forging of Aluminium 6082 Alloy Solid cylinders

    Science.gov (United States)

    Priyadarshini, Amrita; Kiran, C. P.; Suresh, K.

    2018-03-01

    Friction is one of the significant factors in forging operations since it affects metal flow in the die, forming load, strain distribution, tool and die life, surface quality of the product etc. In upset forging, the frictional forces at the die-workpiece interface oppose the outward flow of the material due to which the specimen develops a barrel shape. As a result, the deformation becomes non-uniform or inhomogeneous which is undesirable. Barreling can be reduced by applying effective lubricant on the surface of the platens. The objective of the present work is to study experimentally the effect of various frictional conditions (dry, grease, mineral oil) on barreling during upset forging of aluminum 6082 solid cylinders of different aspect ratio (length/diameter: 0.5, 0.75, 1). The friction coefficients are determined using the ring compression test. Curvature of barrel is determined based on the assumption that the curvature of the barrel follows the geometry of circular arc.

  5. Near net shape forging of titanium alloy turbine blade

    International Nuclear Information System (INIS)

    Morita, Akiyasu; Hattori, Shigeo; Tani, Kazuhito; Takemura, Atsushi; Ashida, Yoshio

    1991-01-01

    The isothermal forging process has been developed to produce turbine blades made of near β Ti-alloy Ti-10V-2Fe-3Al. It is important to set the preform at the optimum position of the die in order to get a high precision product. The deformation analysis by using FEM is effective to determine the optimum position. And also it is necessary to avoid buckling induced by the restriction of axial elongation of the material. As a result, Ti-10V-2Fe-3Al blades could be formed precisely by using only one stage of forging, and machining was needed only at the root. The thickness of the oxide layer induced on the surface of the forged blade was only 70μm. The mechanical properties of Ti-10V-2Fe-3Al blades after forging and annealing were superior to those of Ti-6Al-4V blades and were nearly uniform across the length of the blades. (author)

  6. Superplastic forging nitride ceramics

    Science.gov (United States)

    Panda, P.C.; Seydel, E.R.; Raj, R.

    1988-03-22

    A process is disclosed for preparing silicon nitride ceramic parts which are relatively flaw free and which need little or no machining, said process comprising the steps of: (a) preparing a starting powder by wet or dry mixing ingredients comprising by weight from about 70% to about 99% silicon nitride, from about 1% to about 30% of liquid phase forming additive and from 1% to about 7% free silicon; (b) cold pressing to obtain a preform of green density ranging from about 30% to about 75% of theoretical density; (c) sintering at atmospheric pressure in a nitrogen atmosphere at a temperature ranging from about 1,400 C to about 2,200 C to obtain a density which ranges from about 50% to about 100% of theoretical density and which is higher than said preform green density, and (d) press forging workpiece resulting from step (c) by isothermally uniaxially pressing said workpiece in an open die without initial contact between said workpiece and die wall perpendicular to the direction of pressing and so that pressed workpiece does not contact die wall perpendicular to the direction of pressing, to substantially final shape in a nitrogen atmosphere utilizing a temperature within the range of from about 1,400 C to essentially 1,750 C and strain rate within the range of about 10[sup [minus]7] to about 10[sup [minus]1] seconds[sup [minus]1], the temperature and strain rate being such that surface cracks do not occur, said pressing being carried out to obtain a shear deformation greater than 30% whereby superplastic forging is effected.

  7. Gear hot forging process robust design based on finite element method

    International Nuclear Information System (INIS)

    Xuewen, Chen; Won, Jung Dong

    2008-01-01

    During the hot forging process, the shaping property and forging quality will fluctuate because of die wear, manufacturing tolerance, dimensional variation caused by temperature and the different friction conditions, etc. In order to control this variation in performance and to optimize the process parameters, a robust design method is proposed in this paper, based on the finite element method for the hot forging process. During the robust design process, the Taguchi method is the basic robust theory. The finite element analysis is incorporated in order to simulate the hot forging process. In addition, in order to calculate the objective function value, an orthogonal design method is selected to arrange experiments and collect sample points. The ANOVA method is employed to analyze the relationships of the design parameters and design objectives and to find the best parameters. Finally, a case study for the gear hot forging process is conducted. With the objective to reduce the forging force and its variation, the robust design mathematical model is established. The optimal design parameters obtained from this study indicate that the forging force has been reduced and its variation has been controlled

  8. Slip-line field analysis of metal flow during two dimensional forging

    International Nuclear Information System (INIS)

    Fenton, R.G.; Khataan, H.A.

    1981-01-01

    A method of computation and a computer software package were developed for solving problems of two dimensional plastic flow between symmetrical dies of any specified shape. The load required to initiate plastic flow, the stress and velocity distributions in the plastic region of the metal, and the pressure distribution acting on the die are determined. The method can be used to solve any symmetrical plane strain flow problem regardless of the complexity of the die. The accurate solution obtained by this efficient method can provide valuable help to forging die designers. (Author) [pt

  9. DETERMINATION OF THE OPTIMAL TEMPERING TEMPERATURE IN HARD FACING OF THE FORGING DIES

    Directory of Open Access Journals (Sweden)

    Milan Mutavdžić

    2012-06-01

    Full Text Available Here is analyzed selection of the optimal technology for heat treatment during the reparation of the damaged forging dies. Those tools are manufactured from alloyed tool steels for operation at elevated temperatures. Those steels are prone to self-hardening, so in reparatory hard-facing they must be preheated, additionally heated and tempered. During the tempering, in temperature interval 500-600°C, a secondary increase of hardness and decrease of impact toughness occurs, the so-called reversible tempering brittleness. Here is shown that it can be avoided by application of metallurgical and technological measures. Metallurgical measures assume adequate selection of steels. Since the considered steels are per se prone to tempering brittleness, we conducted experimental investigations to define the technological measures to avoid it. Tests on models were conducted: tempering from different temperatures, slow heating and cooling in still air. Hardness measurements showed that at 520°C, the secondary increase of hardness occurs, with drop of the impact toughness. Additional hard-facing tests included samples tempered at various regimes. Samples were prepared for mechanical and metallographic investigations. Results presented illustrate influence of additional heat treatment on structure, hardness and mechanical properties of the hard-faced layers. This enabled establishing the possibility of avoiding the tempering brittleness through technological measures.

  10. Determination of the optimal tempering temperature in hard facing of the forging dies

    Directory of Open Access Journals (Sweden)

    Milan Mutavdžić

    2012-05-01

    Full Text Available Here is analyzed selection of the optimal technology for heat treatment during the reparation of the damaged forging dies. Those tools are manufactured from alloyed tool steels for operation at elevated temperatures. Those steels are prone to self-hardening, so in reparatory hard-facing they must be preheated, additionally heated and tempered. During the tempering, in temperature interval 500-600°C, a secondary increase of hardness and decrease of impact toughness occurs, the so-called reversible tempering brittleness. Here is shown that it can be avoided by application of metallurgical and technological measures. Metallurgical measures assume adequate selection of steels. Since the considered steels are per se prone to tempering brittleness, we conducted experimental investigations to define the technological measures to avoid it. Tests on models were conducted: tempering from different temperatures, slow heating and cooling in still air. Hardness measurements showed that at 520°C, the secondary increase of hardness occurs, with drop of the impact toughness. Additional hard-facing tests included samples tempered at various regimes. Samples were prepared for mechanical and metallographic investigations. Results presented illustrate influence of additional heat treatment on structure, hardness and mechanical properties of the hard-faced layers. This enabled establishing the possibility of avoiding the tempering brittleness through technological measures. 

  11. Multi-field coupling finite element analysis for determining the influence of temperature field on die service life during precision-forming process of steel synchronizer ring

    International Nuclear Information System (INIS)

    Zhao, Jun; Luo, Shan-Ming; Li, Feng-Qiang; Xu, Chen-Bing

    2017-01-01

    Failure analysis shows that increased die temperature caused by severe plastic deformation of material and heat conduction between hot billet and cavity significantly affects the distortion of gear cavity in steel synchronizer ring forging process. The forging process of steel synchronizer ring and die temperature distribution under different forging conditions are analyzed through finite element method. Simulation results show that severe plastic deformation occurs in the gear cavity. The improvement of lubrication condition results in decreased die temperature. When the initial billet temperature is high, the die temperature is also high. Increasing forging speed in a certain range facilitates the die temperature decrease. The distribution of die temperature in synthetic forming technology is more reasonable than that of one step forging. The synthetic forming technology is adopted in production to reduce the effects of severe plastic deformation caused by die temperature. The ejection mechanism and control system of the double disc friction press are improved to reduce the contact time between the hot billet and cavity. Experimental results show that synthetic forming technology is reasonable, and that the die service life is prolonged.

  12. Multi-field coupling finite element analysis for determining the influence of temperature field on die service life during precision-forming process of steel synchronizer ring

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jun; Luo, Shan-Ming; Li, Feng-Qiang; Xu, Chen-Bing [Xiamen University of Technology, Xiamen (China)

    2017-07-15

    Failure analysis shows that increased die temperature caused by severe plastic deformation of material and heat conduction between hot billet and cavity significantly affects the distortion of gear cavity in steel synchronizer ring forging process. The forging process of steel synchronizer ring and die temperature distribution under different forging conditions are analyzed through finite element method. Simulation results show that severe plastic deformation occurs in the gear cavity. The improvement of lubrication condition results in decreased die temperature. When the initial billet temperature is high, the die temperature is also high. Increasing forging speed in a certain range facilitates the die temperature decrease. The distribution of die temperature in synthetic forming technology is more reasonable than that of one step forging. The synthetic forming technology is adopted in production to reduce the effects of severe plastic deformation caused by die temperature. The ejection mechanism and control system of the double disc friction press are improved to reduce the contact time between the hot billet and cavity. Experimental results show that synthetic forming technology is reasonable, and that the die service life is prolonged.

  13. Forging Oxide-Dispersion-Strengthened Superalloys

    Science.gov (United States)

    Harf, F. H.; Glasgow, T. K.; Moracz, D. J.; Austin, C. M.

    1986-01-01

    Cladding of mild steel prevents surface cracking when alloy contacts die. Continual need for improvements in properties of alloys capable of withstanding elevated temperatures. Accomplished by using oxide-dispersion-strengthed superalloys such as Inconel Alloy MA 6000. Elevated tensile properties of forged alloy equal those of hot-rolled MA 6000 bar. Stress-rupture properties somewhat lower than those of bar stock but, at 1,100 degrees C, exceed those of strongest commercial single crystal, directionally solidified and conventionally cast superalloys.

  14. Effect of Cold Forging on Microstructure and MechanicalProperties of Al/SiC Composites

    Science.gov (United States)

    Hanamantraygouda, M. B.; Shivakumar, B. P., Dr; Siddappa, P. N.; Sampathkumar, L.; Prashanth, L.

    2018-02-01

    The objective of this work was to investigate the effect of cold forging on mechanical properties and microstructural study of Al MMCs, at different wt% of SiC and forging cycle. The Al-SiC composite material was fabricated by stir casting method at different weight percentage of SiC such as 2.5, 5, 7.5 and 10%. Further, the deformation characteristics during open-die forging of Al-SiC composite at cold conditions was investigated. Cast and forged composite material was subjected to hardness test, tensile test and impact test. The grain size, microstructure behaviour was investigated using optical microscope. The results show that hardness and strength of Al-SiC composite increases and ductility decreases as compared to Al alloy in both as-cast and forged conditions. Optical microscope images showed that the distribution of SiC in Al matrix was more homogeneous in a forged composite as compared to cast one and reduction of porosity was found. Further, it showed that due to forging cycle the grain size was reduced by 30% to 35% from initial size.

  15. Manufacturing of Precision Forgings by Radial Forging

    International Nuclear Information System (INIS)

    Wallner, S.; Harrer, O.; Buchmayr, B.; Hofer, F.

    2011-01-01

    Radial forging is a multi purpose incremental forging process using four tools on the same plane. It is widely used for the forming of tool steels, super alloys as well as titanium- and refractory metals. The range of application goes from reducing the diameters of shafts, tubes, stepped shafts and axels, as well as for creating internal profiles for tubes in Near-Net-Shape and Net-Shape quality. Based on actual development of a weight optimized transmission input shaft, the specific features of radial forging technology is demonstrated. Also a Finite Element Model for the simulation of the process is shown which leads to reduced pre-processing effort and reduced computing time compared to other published simulation methods for radial forging. The finite element model can be applied to quantify the effects of different forging strategies.

  16. Research Facility for Mechanical Press Closed Gap Adjuster

    Directory of Open Access Journals (Sweden)

    A. A. Ancifirov

    2016-01-01

    Full Text Available The article describes an example of the research facility for closed gap adjustment mechanism based on the KD2128 closed-die forging press. Its rated force with a servo drive used is 630kN. The servo drive consists of a motor with nominal power of 1.57kW and a frequency converter with power of 7.5kW, which has functions of the programmable logic controller.The article notes that such a facility is expedient and useful for practical classes on forging-andstamping machines at the BMSTU Department of «Technology processing by pressure» to demonstrate the capabilities of existing technological facility, learn a design of forging-andstamping machine units, solve the problems of automatic control, monitoring, and diagnostics in blank manufacturing.The article presents a detailed facility diagram of the closed gap adjustment mechanism and its photograph, describes the mechanism and its basic parameters, gives characteristics of the synchronous motor to drive the mechanism, reviews practical works, which the research facility may provide.Based on the four experiments the article estimates an efficiency of the research facilityuse under consideration, especially when modeling a servo motor shaft under the maximum load. The relevant diagrams confirm experimental results, namely: control current, angle of motor shaft and its speed versus time. Thus, upon the diagram analysis it can be noted that the research facility design allows providing kinematics and dynamics of the press closed gap adjuster.This article describes how to determine the closed gap adjusting accuracy of the press. Eight experiments have been conducted to evaluate a working out control signal to the linear movement of the press punch when using the research facility. It is noted that the linear positioning accuracy of the press punch reaches the hundredth parts of a millimeter of the adjustment value that is sufficient to achieve the required precision when performing operations such as

  17. Methods of forging steel

    OpenAIRE

    Pečoler, Primož

    2014-01-01

    The following work presents processes of steel forming, challenges when forging steel, forming machines suitable for forging and which choice of machine is most suitable for forging. We can separate steel forming to free forging and drop forging. Free forging can be divided to hand forging and machine forging. The correct choice of furnaces is also very important. We must reach correct temperature in the furnace for raw steel to melt with less scalings. In diploma I mentioned some machine...

  18. New design of process for cold forging to improve multi-stage gas fitting

    Directory of Open Access Journals (Sweden)

    Han-Sung Huang

    2016-04-01

    Full Text Available This work develops a process that solves the problem of the formation of cracks inside forged gas fittings in the cold forging process that arises from poor forging process design. DEFORM-3D forming software was utilized, and macroscopic experiments with optical microscopy and scanning electron microscopy were conducted to investigate the processed structures and the distribution therein of metal flow lines, and to find the internal micro-cracks to determine whether the cold forging process is reasonable. Analytical results herein demonstrate that the stress and strain inside the gas fitting can be elucidated using metal forming software. Together with experimental results, they demonstrate that a concentration of stress damages the workpiece in the forming process. Moreover, as metal flow lines become narrower, the workpiece becomes more easily damaged. Consequently, the improved cold forging process that is described in this work should be utilized to reduce the occurrence of fine cracks and defects. Planning for proper die design and production, increasing the quality of products, and reducing the number of defective products promote industrial competitiveness.

  19. Effects of HIP and forging on fracture behaviour in cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure

    International Nuclear Information System (INIS)

    Uematsu, Y.; Tokaji, K.; Nishigaki, K.; Okajima, D.; Ogasawara, M.

    2010-01-01

    The cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure was developed as a die material due to its high hardness. In order to achieve high performances of dies, not only the hardness but also the mechanical properties such as fracture toughness and fatigue crack propagation (FCP) resistance should be improved. In this paper, hot isostatic pressing (HIP) or forging was applied to the cast iron to improve mechanical properties, and the fracture behaviour, such as flexural strength, fracture toughness and FCP, was studied. The average flexural strength was reduced by forging because of the enhanced notch sensitivity due to the increase in the hardness. The fracture toughness was not affected by HIP nor forging while its scatter was significantly reduced by both post-treatments. The intrinsic FCP resistance taking account of crack closure was the same regardless of the application of HIP or forging, indicating that a slight change in the microstructure resulting from both treatments and the presence of casting defects exerted little influence on FCP behaviour. It could be concluded that both HIP and forging could improve the hardness of the material, while fracture toughness and FCP resistance were maintained.

  20. Intersubjective decision-making for computer-aided forging technology design

    Science.gov (United States)

    Kanyukov, S. I.; Konovalov, A. V.; Muizemnek, O. Yu.

    2017-12-01

    We propose a concept of intersubjective decision-making for problems of open-die forging technology design. The intersubjective decisions are chosen from a set of feasible decisions using the fundamentals of the decision-making theory in fuzzy environment according to the Bellman-Zadeh scheme. We consider the formalization of subjective goals and the choice of membership functions for the decisions depending on subjective goals. We study the arrangement of these functions into an intersubjective membership function. The function is constructed for a resulting decision, which is chosen from a set of feasible decisions. The choice of the final intersubjective decision is discussed. All the issues are exemplified by a specific technological problem. The considered concept of solving technological problems under conditions of fuzzy goals allows one to choose the most efficient decisions from a set of feasible ones. These decisions correspond to the stated goals. The concept allows one to reduce human participation in automated design. This concept can be used to develop algorithms and design programs for forging numerous types of forged parts.

  1. Fabrication Improvement of Cold Forging Hexagonal Nuts by Computational Analysis and Experiment Verification

    Directory of Open Access Journals (Sweden)

    Shao-Yi Hsia

    2015-01-01

    Full Text Available Cold forging has played a critical role in fasteners and has been applied to the automobile industry, construction industry, aerospace industry, and living products so that cold forging presents the opportunities for manufacturing more products. By using computer simulation, this study attempts to analyze the process of creating machine parts, such as hexagonal nuts. The DEFORM-3D forming software is applied to analyze the process at various stages in the computer simulation, and the compression test is also used for the flow stress equation in order to compare the differences between the experimental results and the equation that is built into the computer simulation software. At the same time, the metallography and hardness of experiments are utilized to understand the cold forging characteristics of hexagonal nuts. The research results would benefit machinery businesses to realize the forging load and forming conditions at various stages before the fastener formation. In addition to planning proper die design and production, the quality of the produced hexagonal nuts would be more stable to promote industrial competitiveness.

  2. Evolution of A-Type Macrosegregation in Large Size Steel Ingot After Multistep Forging and Heat Treatment

    Science.gov (United States)

    Loucif, Abdelhalim; Ben Fredj, Emna; Harris, Nathan; Shahriari, Davood; Jahazi, Mohammad; Lapierre-Boire, Louis-Philippe

    2018-06-01

    A-type macrosegregation refers to the channel chemical heterogeneities that can be formed during solidification in large size steel ingots. In this research, a combination of experiment and simulation was used to study the influence of open die forging parameters on the evolution of A-type macrosegregation patterns during a multistep forging of a 40 metric ton (MT) cast, high-strength steel ingot. Macrosegregation patterns were determined experimentally by macroetch along the longitudinal axis of the forged and heat-treated ingot. Mass spectroscopy, on more than 900 samples, was used to determine the chemical composition map of the entire longitudinal sectioned surface. FORGE NxT 1.1 finite element modeling code was used to predict the effect of forging sequences on the morphology evolution of A-type macrosegregation patterns. For this purpose, grain flow variables were defined and implemented in a large scale finite element modeling code to describe oriented grains and A-type segregation patterns. Examination of the A-type macrosegregation showed four to five parallel continuous channels located nearly symmetrical to the axis of the forged ingot. In some regions, the A-type patterns became curved or obtained a wavy form in contrast to their straight shape in the as-cast state. Mass spectrometry analysis of the main alloying elements (C, Mn, Ni, Cr, Mo, Cu, P, and S) revealed that carbon, manganese, and chromium were the most segregated alloying elements in A-type macrosegregation patterns. The observed differences were analyzed using thermodynamic calculations, which indicated that changes in the chemical composition of the liquid metal can affect the primary solidification mode and the segregation intensity of the alloying elements. Finite element modeling simulation results showed very good agreement with the experimental observations, thereby allowing for the quantification of the influence of temperature and deformation on the evolution of the shape of the

  3. Simulation and experimental verification of the filling process of semi-solid die forging for cup shell

    Directory of Open Access Journals (Sweden)

    Jianbo TAN

    2015-06-01

    Full Text Available The filling mold process of semi-solid alloy blank influences severely the forming and properties of finished piece. In this paper, DEFORM is applied to simulate the process of cup-type 6061 alloy die forging casting. The influences of the temperature of semi-solid alloy blank, preheating temperature, and downward press speed of pressure head on process of mold filling and velocity field are investigated. The results show that the mold filling of semi-solid alloy paste smoothly fills along the whole of mould cavity in “total wall thickness” form when the temperature of semi-solid alloy blank is 620 ℃, preheating temperature of pressure head is 200 ℃ and speed of pressure head is 40 mm/s. Along with the increase of the preheating temperature of pressure head, the filling process of the semi-solid alloy paste trends toward stable when the temperature of semi-solid alloy blank is 620 ℃ and the speed of pressure head is 20 mm/s. Along with the increasing of the temperature of semi-solid alloy, the process of mould filling becomes off balance and the liquid becomes turbulent flow. The velocity field in the process of mould filling affects severely the structure uniformity of the finished product.

  4. An alternative design method for the double-layer combined die using autofrettage theory

    Directory of Open Access Journals (Sweden)

    C. Hu

    2017-08-01

    Full Text Available The double-layer combined die is used for its longer life in forging. Autofrettage is a well-known elastic–plastic technology that increases the durability of thick-walled cylinders. This study explores an alternative design method of the double-layer combined die using autofrettage theory. An analytical solution for the autofrettage process of the double-layer combined die is obtained based on Lamé's equation. The relationship between the autofrettage pressure and the yield radius of the die insert is obtained, and expressions of residual stresses and displacements, which are directly related to geometric parameters, material properties and internal pressure, are derived. The finite-element simulation of a specific case is performed, and good agreement between theoretical calculations and simulation results is found. Furthermore, the effects of important parameters, including the ratio of the plastic area and yield strength of the die insert and the outer diameters of the die insert and stress ring, on the autofrettage effect are investigated. Compared with the conventional combined die, the autofrettaged die can bear larger working pressure, as expected. The use of the autofrettaged die can reduce the amount of expensive material required for the die insert and the working space of the die set, which would benefit the practical forging process.

  5. Development of strategies for saving energy by temperature reduction in warm forging processes

    Science.gov (United States)

    Varela, Sonia; Santos, Maite; Vadillo, Leire; Idoyaga, Zuriñe; Valbuena, Óscar

    2016-10-01

    This paper is associated to the European policy of increasing efficiency in raw material and energy usage. This policy becomes even more important in sectors consuming high amount of resources, like hot forging industry, where material costs sums up to 50% of component price and energy ones are continuously raising. The warm forging shows a clear potential of raw material reduction (near-net-shape components) and also of energy saving (forging temperature under 1000°C). However and due to the increment of the energy costs, new solutions are required by the forging sector in order to reduce the temperature below 900°C. The reported research is based on several approaches to reduce the forging temperature applied to a flanged shaft of the automotive sector as demonstration case. The developed investigations have included several aspects: raw material, process parameters, tools and dies behavior during forging process and also metallographic evaluation of the forged parts. This paper summarizes analysis of the ductility and the admissible forces of the flanged shaft material Ck45 in as-supplied state (as-rolled) and also in two additional heat treated states. Hot compression and tensile tests using a GLEEBLE 3800C Thermo mechanical simulator have been performed pursuing this target. In the same way, a coupled numerical model based on Finite Element Method (FEM) has been developed to predict the material flow, the forging loads and the stresses on the tools at lower temperature with the new heat treatments of the raw material. In order to validate the previous development, experimental trials at 850 °C and 750 °C were carried out in a mechanical press and the results were very promising.

  6. Analysis of the thermo-mechanical deformations in a hot forging tool by numerical simulation

    International Nuclear Information System (INIS)

    L-Cancelos, R.; Varas, F.; Viéitez, I.; Martín, E.

    2016-01-01

    Although programs have been developed for the design of tools for hot forging, its design is still largely based on the experience of the tool maker. This obliges to build some test matrices and correct their errors to minimize distortions in the forged piece. This phase prior to mass production consumes time and material resources, which makes the final product more expensive. The forging tools are usually constituted by various parts made of different grades of steel, which in turn have different mechanical properties and therefore suffer different degrees of strain. Furthermore, the tools used in the hot forging are exposed to a thermal field that also induces strain or stress based on the degree of confinement of the piece. Therefore, the mechanical behaviour of the assembly is determined by the contact between the different pieces. The numerical simulation allows to analyse different configurations and anticipate possible defects before tool making, thus, reducing the costs of this preliminary phase. In order to improve the dimensional quality of the manufactured parts, the work presented here focuses on the application of a numerical model to a hot forging manufacturing process in order to predict the areas of the forging die subjected to large deformations. The thermo-mechanical model developed and implemented with free software (Code-Aster) includes the strains of thermal origin, strains during forge impact and contact effects. The numerical results are validated with experimental measurements in a tooling set that produces forged crankshafts for the automotive industry. The numerical results show good agreement with the experimental tests. Thereby, a very useful tool for the design of tooling sets for hot forging is achieved. (paper)

  7. Analysis of the thermo-mechanical deformations in a hot forging tool by numerical simulation

    Science.gov (United States)

    L-Cancelos, R.; Varas, F.; Martín, E.; Viéitez, I.

    2016-03-01

    Although programs have been developed for the design of tools for hot forging, its design is still largely based on the experience of the tool maker. This obliges to build some test matrices and correct their errors to minimize distortions in the forged piece. This phase prior to mass production consumes time and material resources, which makes the final product more expensive. The forging tools are usually constituted by various parts made of different grades of steel, which in turn have different mechanical properties and therefore suffer different degrees of strain. Furthermore, the tools used in the hot forging are exposed to a thermal field that also induces strain or stress based on the degree of confinement of the piece. Therefore, the mechanical behaviour of the assembly is determined by the contact between the different pieces. The numerical simulation allows to analyse different configurations and anticipate possible defects before tool making, thus, reducing the costs of this preliminary phase. In order to improve the dimensional quality of the manufactured parts, the work presented here focuses on the application of a numerical model to a hot forging manufacturing process in order to predict the areas of the forging die subjected to large deformations. The thermo-mechanical model developed and implemented with free software (Code-Aster) includes the strains of thermal origin, strains during forge impact and contact effects. The numerical results are validated with experimental measurements in a tooling set that produces forged crankshafts for the automotive industry. The numerical results show good agreement with the experimental tests. Thereby, a very useful tool for the design of tooling sets for hot forging is achieved.

  8. A material based approach to creating wear resistant surfaces for hot forging

    Science.gov (United States)

    Babu, Sailesh

    Tools and dies used in metal forming are characterized by extremely high temperatures at the interface, high local pressures and large metal to metal sliding. These harsh conditions result in accelerated wear of tooling. Lubrication of tools, done to improve metal flow drastically quenches the surface layers of the tools and compounds the tool failure problem. This phenomenon becomes a serious issue when parts forged at complex and are expected to meet tight tolerances. Unpredictable and hence uncontrolled wear and degradation of tooling result in poor part quality and premature tool failure that result in high scrap, shop downtime, poor efficiency and high cost. The objective of this dissertation is to develop a computer-based methodology for analyzing the requirements hot forging tooling to resist wear and plastic deformation and wear and predicting life cycle of forge tooling. Development of such is a system is complicated by the fact that wear and degradation of tooling is influenced by not only the die material used but also numerous process controls like lubricant, dilution ratio, forging temperature, equipment used, tool geometries among others. Phenomenological models available u1 the literature give us a good thumb rule to selecting materials but do not provide a way to evaluate pits performance in field. Once a material is chosen, there are no proven approaches to create surfaces out of these materials. Coating approaches like PVD and CVD cannot generate thick coatings necessary to withstand the conditions under hot forging. Welding cannot generate complex surfaces without several secondary operations like heat treating and machining. If careful procedures are not followed, welds crack and seldom survive forging loads. There is a strong need for an approach to selectively, reliably and precisely deposit material of choice reliably on an existing surface which exhibit not only good tribological properties but also good adhesion to the substrate

  9. Forging Long Shafts On Disks

    Science.gov (United States)

    Tilghman, Chris; Askey, William; Hopkins, Steven

    1989-01-01

    Isothermal-forging apparatus produces long shafts integral with disks. Equipment based on modification of conventional isothermal-forging equipment, required stroke cut by more than half. Enables forging of shafts as long as 48 in. (122 cm) on typical modified conventional forging press, otherwise limited to making shafts no longer than 18 in. (46cm). Removable punch, in which forged material cools after plastic deformation, essential novel feature of forging apparatus. Technology used to improve such products as components of gas turbines and turbopumps and of other shaft/disk parts for powerplants, drive trains, or static structures.

  10. Research on Energy-Saving Production Scheduling Based on a Clustering Algorithm for a Forging Enterprise

    Directory of Open Access Journals (Sweden)

    Yifei Tong

    2016-02-01

    Full Text Available Energy efficiency is a buzzword of the 21st century. With the ever growing need for energy efficient and low-carbon production, it is a big challenge for high energy-consumption enterprises to reduce their energy consumption. To this aim, a forging enterprise, DVR (the abbreviation of a forging enterprise, is researched. Firstly, an investigation into the production processes of DVR is given as well as an analysis of forging production. Then, the energy-saving forging scheduling is decomposed into two sub-problems. One is for cutting and machining scheduling, which is similar to traditional machining scheduling. The other one is for forging and heat treatment scheduling. Thirdly, former forging production scheduling is presented and solved based on an improved genetic algorithm. Fourthly, the latter is discussed in detail, followed by proposed dynamic clustering and stacking combination optimization. The proposed stacking optimization requires making the gross weight of forgings as close to the maximum batch capacity as possible. The above research can help reduce the heating times, and increase furnace utilization with high energy efficiency and low carbon emissions.

  11. Cavity closure during compression between semi-closed die using superplastic tin-lead alloy

    International Nuclear Information System (INIS)

    Zaid, A. I. O.; Al-Tamimi, M. M.

    2013-01-01

    Superplasticity is a feature of a material or alloy, which allows the material to deform plastically to an extremely large strain at low values of stress under certain loading conditions of strain rate and temperature. Eutectic tin-lead alloy is a practical material for research investigations as it possesses a superplastic behavior at room temperature and low strain rate which makes it a useful tool in simulating the ordinary engineering materials at high strain rate and temperature, and has been extensively used as a model material. In this paper, superplastic tin-lead alloy was used at room temperature to simulate the closure of cavities in steels at high temperatures in the hot region under dynamic loading (high strain rate) under the effect of compressive loads using semi-closed dies (modified dies) with 45 degree inclination and compare the results from these dies with those of flat platens (open dies) published previously. Hollow specimens having different values of bore diameter (Db) to outer diameter (Dout), of the same height and volume were investigated under 40% height reduction. The cavity closure for each specimen was determined. Comparison is made between flat platens and semi-closed dies regarding cavity closure based on bore diameter, bore volume, reduction percentage in bore diameter and reduction percentage in bore volume, at the 40% reduction in height. It was found that modifying the platens (45 degree inclination) resulted in lower values of bore diameters and volume i.e. higher values of reduction in bore diameters and volumes percentages irrespective of the value of bore diameter and the ratio of Db/Dout. (author)

  12. Forging Industry Leadtimes: An Analysis of Causes for and Solutions to Long Leadtimes for Aerospace Forgings

    Science.gov (United States)

    1986-09-01

    Pamplet . Forging Industry Association, Cleveland-MT, uncatea. 20. Forging Industry Association, and American Society for Metals. Forging Handbook, edited... Pamplet . The Harris-Thomas Drop Forge Compnyayto--n R, undated. 43. Theeck, Michael F., TECH MOD Program Mana.er. Personal interview. Industrial Base... Brochure . Worcester MA, 3, . 125 "’ VITA Captain Stephen F. O’Neill was born on 19 June 1957 in Pittsfield, Massachusetts. He graduated from high school

  13. Microstructure Evolution and Surface Cracking Behavior of Superheavy Forgings during Hot Forging

    Directory of Open Access Journals (Sweden)

    Zhenhua Wang

    2018-01-01

    Full Text Available In recent years, superheavy forgings that are manufactured from 600 t grade ingots have been applied in the latest generation of nuclear power plants to provide good safety. However, component production is pushing the limits of the current free-forging industry. Large initial grain sizes and a low strain rate are the main factors that contribute to the deformation of superheavy forgings during forging. In this study, 18Mn18Cr0.6N steel with a coarse grain structure was selected as a model material. Hot compression and hot tension tests were conducted at a strain rate of 10−4·s−1. The essential nucleation mechanism of the dynamic recrystallization involved low-angle grain boundary formation and subgrain rotation, which was independent of the original high-angle grain boundary bulging and the presence of twins. Twins were formed during the growth of dynamic recrystallization grains. The grain refinement was not obvious at 1150°C. A lowering of the deformation temperature to 1050°C resulted in a fine grain structure; however, the stress increased significantly. Crack-propagation paths included high-angle grain boundaries, twin boundaries, and the insides of grains, in that order. For superheavy forging, the ingot should have a larger height and a smaller diameter.

  14. Microstructural and mechanical evolutions during the forging step of the COBAPRESS, a casting/forging process

    Science.gov (United States)

    Perrier, Frédéric; Desrayaud, Christophe; Bouvier, Véronique

    Aluminum casting/forging processes are used to produce parts for the automotive industry. In this study, we examined the influence of the forging step on the microstructure and the mechanical properties of an A356 aluminum alloy modified with strontium. Firstly, a design of samples which allows us to test mechanically the alloy before and after forging was created. A finite element analysis with the ABAQUS software predicts a maximum of strain in the core of the specimens. Observations with the EBSD technique confirm a more intense sub-structuration of the dendrite cells in this zone. Yield strength, ultimate tensile strength, elongation and fatigue lives were then improved for the casting/forging samples compared to the only cast specimens. The closure of the porosities and the improvement of the surface quality during the forging step enhance also the fatigue resistance of the samples.

  15. 29 CFR 1910.218 - Forging machines.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 5 2010-07-01 2010-07-01 false Forging machines. 1910.218 Section 1910.218 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.218 Forging machines. (a... other identifier, for the forging machine which was inspected. (ii) Scheduling and recording the...

  16. The Influence of Technological Conditions of the Process of Cogging in Flat Dies on the Quality of Two-Phase Titanium Alloys

    Directory of Open Access Journals (Sweden)

    Dyja Н.

    2016-06-01

    Full Text Available To create a rational technology of cogging process and to determinate the optimal values of the angles of tilt and single reduction the stress-strain state (SSS of the blank during cogging in the flat dies was analyzed. By using the finite element method and program MSC.SuperForge quantitative data are obtained and the basic patterns of distribution of SSS, the temperature during the simulation of tilting in flat dies with different angles of tilting and the amount of reduction were established. Sustainable experimental-industrial technology of forging of two-phase titanium alloys was developed and tested.

  17. 48 CFR 225.7102 - Forgings.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Forgings. 225.7102 Section 225.7102 Federal Acquisition Regulations System DEFENSE ACQUISITION REGULATIONS SYSTEM, DEPARTMENT OF... Forgings. ...

  18. High-Speed Coating Method for Photovoltaic Textiles with Closed-Type Die Coater

    Science.gov (United States)

    Imai, Takahiko; Shibayama, Norihisa; Takamatsu, Seiichi; Shiraishi, Kenji; Marumoto, Kazuhiro; Itoh, Toshihiro

    2013-06-01

    We developed a closed-type die-coating method to fabricate thin films for electronic devices. We succeeded in the die-coating of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) water dispersions and regioregular poly(3-hexylthiophene):[6,6]-phenyl C61-butyric acid methyl ester (P3HT:PCBM) solution to fabricate thin films of these organic materials with extremely high speeds of 5 and 20 m/min, respectively. The film thicknesses were evaluated by cross-sectional scanning electron microscopy (SEM). The deviations of the film thicknesses from our target values were less than 5%. We fabricated Al/P3HT:PCBM/PEDOT:PSS/indium tin oxide (ITO)/poly(ethylene terephthalate) (PET) textiles as an example of an application of the method, and the photovoltaic characteristic of the devices was confirmed.

  19. The Use of 3D Scanning Methods to Evaluate the Hybrid Layer Used in Forging Tools in Order to Improve their Durability

    Directory of Open Access Journals (Sweden)

    Gronostajski Z.

    2017-09-01

    Full Text Available This study is focused on tools used in the industrial process of hot forging of a front wheel forging (gear wheel manufactured for the automotive industry. Five different variants were applied for the tools: 3 die inserts were coated with three different hybrid layers (PN + PVD type, i.e. AlCrTiN, AlCrTiSiN and CrN, one insert was only nitrided, and one was pad welded, to improve tool durability. The tool wear was analysed and represented by the material degradation on the working surface, based on the 3D scanning and the material growth of the periodically collected forgings. Additionally, the scanned tools were divided into two areas, in which it was found, based on the analysis, that various degradation mechanisms are predominant. Microstructural tests and hardness measurements of the analyzed tools were also performed. Based on the results, it was found that, in the central part of the die insert, thermo-mechanical fatigue, abrasive wear and plastic deformation occurred, while in the area of the bridge insert, only abrasive wear could be observed. For these areas, the loss of material was determined separately. It was established that the use of the GN+CrN and GN+AlCrTiN hybrid layers on forging tools improves their durability, while the best results in the central area were observed on the tool with the GN+CrN layer, which is the most resistant to thermo-mechanical fatigue. In the second analyzed area, good wear resistance occurred on GN+CrN, GN+AlCrTiN and pad welded inserts, for which, together with the increase of the forging number, a proportional, slight growth of the loss of material occurred.

  20. Sensitivity Analysis of Oxide Scale Influence on General Carbon Steels during Hot Forging

    Directory of Open Access Journals (Sweden)

    Bernd-Arno Behrens

    2018-02-01

    Full Text Available Increasing product requirements have made numerical simulation into a vital tool for the time- and cost-efficient process design. In order to accurately model hot forging processes with finite, element-based numerical methods, reliable models are required, which take the material behaviour, surface phenomena of die and workpiece, and machine kinematics into account. In hot forging processes, the surface properties are strongly affected by the growth of oxide scale, which influences the material flow, friction, and product quality of the finished component. The influence of different carbon contents on material behaviour is investigated by considering three different steel grades (C15, C45, and C60. For a general description of the material behaviour, an empirical approach is used to implement mathematical functions for expressing the relationship between flow stress and dominant influence variables like alloying elements, initial microstructure, and reheating mode. The deformation behaviour of oxide scale is separately modelled for each component with parameterized flow curves. The main focus of this work lies in the consideration of different materials as well as the calculation and assignment of their material properties in dependence on current process parameters by application of subroutines. The validated model is used to carry out the influence of various oxide scale parameters, like the scale thickness and the composition, on the hot forging process. Therefore, selected parameters have been varied within a numerical sensitivity analysis. The results show a strong influence of oxide scale on the friction behaviour as well as on the material flow during hot forging.

  1. Forging of Advanced Disk Alloy LSHR

    Science.gov (United States)

    Gabb, Timothy P.; Gayda, John; Falsey, John

    2005-01-01

    The powder metallurgy disk alloy LSHR was designed with a relatively low gamma precipitate solvus temperature and high refractory element content to allow versatile heat treatment processing combined with high tensile, creep and fatigue properties. Grain size can be chiefly controlled through proper selection of solution heat treatment temperatures relative to the gamma precipitate solvus temperature. However, forging process conditions can also significantly influence solution heat treatment-grain size response. Therefore, it is necessary to understand the relationships between forging process conditions and the eventual grain size of solution heat treated material. A series of forging experiments were performed with subsequent subsolvus and supersolvus heat treatments, in search of suitable forging conditions for producing uniform fine grain and coarse grain microstructures. Subsolvus, supersolvus, and combined subsolvus plus supersolvus heat treatments were then applied. Forging and subsequent heat treatment conditions were identified allowing uniform fine and coarse grain microstructures.

  2. Role of forgings in powder metallurgy industry

    International Nuclear Information System (INIS)

    Hayes, A.F.; DeRidder, A.J.

    1975-01-01

    Forging of powder metallurgy materials is discussed. Information and data are included on forging powder metallurgy W, Mo, In 100, Rene 95, Astroloy, Be, and Ti. It is noted that the combination of powder metallurgy and forging work provides the best product from standpoints of reproducibility, freedom from segregation, low scrap rate, and uniform mechanical properties. Experience is being used to develop contour forging from hot isostatic pressed billets or preforms. The quality of this product is under evaluation. Results show steady improvement and it is anticipated that continued effort will soon produce a reliable, less costly product. Forging can continue to be relied upon to correct subtle defects present in powder metallurgy material

  3. Electro sinter forging of titanium disks

    DEFF Research Database (Denmark)

    Cannella, Emanuele; Nielsen, Chris Valentin; Bay, Niels Oluf

    by measuring the electrical resistance during the sintering process [5], since low electrical resistance corresponds to high density. It is, however, necessary to be aware that increased temperature, on the other hand, increases the resistance. SEM micrographs and Computed Tomography (CT) are carried out......Electro sinter forging (ESF) is a new sintering process based on the principle of electrical Joule heating. In the present work, middle frequency direct current (MFDC) was flowing through the powder compact, which was under mechanical pressure. The main parameters are the high electrical current......, up to 10 kA, and the low voltage, 1-2 V, resulting in heat generation in the powder. Figure 1 shows the experimental setup. The punches were made of a conductive material; namely a copper alloy. The die, which has to be electrically insulating, was made of alumina. The ESF process takes 3-4s...

  4. Heavy forgings for reactor pressure vessels

    International Nuclear Information System (INIS)

    Cerjak, H.; Papouschek, F.

    1979-01-01

    The importance of forgings for an optimal design of nuclear components is described. Problems concerning the correlation of requirements, material behavior, fabrication and testing of forgings are discussed. (orig.) [de

  5. International cooperation in cold forging technology

    DEFF Research Database (Denmark)

    Bay, Niels; Lange, K

    1992-01-01

    International cooperation in the field of cold forging technology started in 1961 by formation of the OECD Group of Experts on Metal Forming. In 1967 this group was transformed into the International Cold Forging Group, ICFG, an independent body which has now been operative for 25 years. Members...... of the ICFG are personally elected by the Plenary as experts within the field, often representing national groups within cold forging. The main work within the ICFG is carried out in its subgroups which are established by the Plenary to collect, compile and evaluate data and eventually also produce data...... by cooperative activities or by instigating national research. These subgroups have produced 9 data sheets and 7 guidelines on subjects such as materials, tool design and construction, calculation methods for cold forging tools, manufacture of slugs, lubrication aspects and small quantity production. Plenary...

  6. Methods and Algorithms for Computer-aided Engineering of Die Tooling of Compressor Blades from Titanium Alloy

    Science.gov (United States)

    Khaimovich, A. I.; Khaimovich, I. N.

    2018-01-01

    The articles provides the calculation algorithms for blank design and die forming fitting to produce the compressor blades for aircraft engines. The design system proposed in the article allows generating drafts of trimming and reducing dies automatically, leading to significant reduction of work preparation time. The detailed analysis of the blade structural elements features was carried out, the taken limitations and technological solutions allowed to form generalized algorithms of forming parting stamp face over the entire circuit of the engraving for different configurations of die forgings. The author worked out the algorithms and programs to calculate three dimensional point locations describing the configuration of die cavity.

  7. Press forging and optical properties of lithium fluoride

    Science.gov (United States)

    Ready, J. F.; Vora, H.

    1980-07-01

    Lithium fluoride is an important candidate material for windows on high power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals were press forged in one step over the temperature range 300 to 600 C to obtain fine grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40 percent at 400 C to 65 percent at 600 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 C, to total deformations of 69 to 76 percent, with intermediate annealing at 700 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one step forging. The results of characterization of various optical and mechanical properties of single crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described.

  8. Press forging and optical properties of lithium fluoride

    International Nuclear Information System (INIS)

    Ready, J.F.; Vora, H.

    1979-01-01

    Lithium fluoride is an important candidate material for windows on high-power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals have been press forged in one step over the temperature range 300 to 600 0 c to obtain fine-grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40% at 400 0 C to 65% at 600 0 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 0 C, to total deformations of 69-76%, with intermediate annealing at 700 0 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one-step forging. The results of characterization of various optical and mechanical properties of single-crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described

  9. Quality assurance for hammer forgings

    International Nuclear Information System (INIS)

    Potthast, E.

    1984-01-01

    The quality assurance program introduced by Arbed Saarstahl and laid down in a quality assurance manual is described. A particular attention is attached thereby both to quality practice proper and to a reliable flow of information amongst all the persons involved. The production and test sequence schedules of the hammer forging plant are illustrated by the example of a forged valve housing for nuclear power plants. These schedules specify not only the forging process in the individual production stages but also the workpiece contour after each working operation, the heat treatment, the furnace charging, and the inspection of finished parts. The formalization of the tests is designed both to promote the customer's trust towards the supplier and to prevent the formal operations involved from hindering further technical development. (orig.) [de

  10. Co-Operative Training in the Sheffield Forging Industry

    Science.gov (United States)

    Duncan, R.

    2008-01-01

    Purpose: The purpose of this paper is to give details of an operation carried out in Sheffield to increase the recruitment of young men into the steel forging industry. Design/methodology/approach: The Sheffield Forges Co-operative Training Scheme was designed to encourage boys to enter the forging industry and to provide them with training and…

  11. Design and economic justification of group blanks application

    Directory of Open Access Journals (Sweden)

    V. Todić

    2012-04-01

    Full Text Available Within the manufacturing process planning, blanks are either selected or designed, respectively forms of input material for the manufacture of products. Reviewed in this paper are three types of group blanks: group castings, group forgings manufactured by closed die forging and free forging, and group blanks manufactured by pressing melted metal in casts. The paper also presents requisites for design and evaluation of economic justification of group blanks application.

  12. Development of integral type forgings for steam generator of nuclear power plant

    International Nuclear Information System (INIS)

    Suzuki, Komei; Sato, Ikuo; Murai, Etsuo

    1992-01-01

    The use of integral type steel forgings for the construction of pressure vessel enhances the structural integrity of components and makes the fabrication of components and the execution of in-service inspection (ISI) easier than those fabrication from plate and casting materials. Such steel forgings have been realized for steam generator (SG) for nuclear power plant as follows : (1) Forged shell ring : change from welding fabrication of formed plates to forging ; (2) Forged conical shell ring : ditto ; (3) Forged head integral with nozzles (s) : (i) Primary head : change from casting to forging ; (ii) Secondary head : change from welding fabrication of formed plates to forging. These steel forgings have been realized by recent development in manufacturing technologies, such as steel making, forging processes and heat treatment which are vital to the quality of steel forgings. Some examples of recent typical high quality steel forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced, and the main points of the manufacturing technique and the quality attained are also described. (author)

  13. Influence of the hydrostatic stress component on critical surface expansion in forging compound products

    DEFF Research Database (Denmark)

    Vorm, T; Bay, Niels; Wanheim, Tarras

    1974-01-01

    of a superimposed hydrostatic pressure on the critical surface expansion during a forging process. The critical surface expansion appears to decrease with increasing hydrostatic pressure. This may be due to the fact that the close contact between the materials necessary to obtain bonding is created by a micro...

  14. Phased Array Ultrasonic Inspection of Titanium Forgings

    International Nuclear Information System (INIS)

    Howard, P.; Klaassen, R.; Kurkcu, N.; Barshinger, J.; Chalek, C.; Nieters, E.; Sun, Zongqi; Fromont, F. de

    2007-01-01

    Aerospace forging inspections typically use multiple, subsurface-focused sound beams in combination with digital C-scan image acquisition and display. Traditionally, forging inspections have been implemented using multiple single element, fixed focused transducers. Recent advances in phased array technology have made it possible to perform an equivalent inspection using a single phased array transducer. General Electric has developed a system to perform titanium forging inspection based on medical phased array technology and advanced image processing techniques. The components of that system and system performance for titanium inspection will be discussed

  15. 22 CFR 121.10 - Forgings, castings and machined bodies.

    Science.gov (United States)

    2010-04-01

    ... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Forgings, castings and machined bodies. 121.10... STATES MUNITIONS LIST Enumeration of Articles § 121.10 Forgings, castings and machined bodies. Articles on the U.S. Munitions List include articles in a partially completed state (such as forgings...

  16. Kinematics at the Main Mechanism of a Railbound Forging Manipulator

    Directory of Open Access Journals (Sweden)

    Florian Ion Tiberiu Petrescu

    2015-09-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 Heavy payload forging manipulators are mainly characterized by large load output and large capacitive load input. The relationship between outputs and inputs will greatly influence the control and the reliability. Forging manipulators have become more prevalent in the industry today. They are used to manipulate objects to be forged. The most common forging manipulators are moving on a railway to have a greater precision and stability. They have been called the railbound forging manipulators. In this paper we analyze the general kinematics of the main mechanism from a such manipulator. Kinematic scheme shows a typical forging manipulator, with the basic motions in operation process: walking, motion of the tong and buffering. The lifting mechanism consists of several parts including linkages, hydraulic drives and motion pairs. The principle of type design from the viewpoints of the relationship between output characteristics and actuator inputs is discussed. An idea of establishing the incidence relationship between output characteristics and actuator inputs is proposed. These novel forging manipulators which satisfy certain functional requirements provide an effective help for the design of forging manipulators.

  17. Study on the isothermal forging process of MB26 magnesium alloy adaptor

    Directory of Open Access Journals (Sweden)

    Xu Wenchen

    2015-01-01

    Full Text Available The isothermal forging process is an effective method to manufacture complex-shaped components of hard-to-work materials, such as magnesium alloys. This study investigates the isothermal forging process of an MB26 magnesium alloy adaptor with three branches. The results show that two-step forging process is appropriate to form the adaptor forging, which not only improves the filling quality but also reduces the forging load compared with one-step forging process. Moreover, the flow line is distributed along the contour of the complex-shaped adaptor forging.

  18. Near-Net Forging Technology Demonstration Program

    Science.gov (United States)

    Hall, I. Keith

    1996-01-01

    Significant advantages in specific mechanical properties, when compared to conventional aluminum (Al) alloys, make aluminum-lithium (Al-Li) alloys attractive candidate materials for use in cryogenic propellant tanks and dry bay structures. However, the cost of Al-Li alloys is typically five times that of 2219 aluminum. If conventional fabrication processes are employed to fabricate launch vehicle structure, the material costs will restrict their utilization. In order to fully exploit the potential cost and performance benefits of Al-Li alloys, it is necessary that near-net manufacturing methods be developed to off-set or reduce raw material costs. Near-net forging is an advanced manufacturing method that uses elevated temperature metal movement (forging) to fabricate a single piece, near-net shape, structure. This process is termed 'near-net' because only a minimal amount of post-forge machining is required. The near-net forging process was developed to reduce the material scrap rate (buy-to-fly ratio) and fabrication costs associated with conventional manufacturing methods. The goal for the near-net forging process, when mature, is to achieve an overall cost reduction of approximately 50 percent compared with conventional manufacturing options for producing structures fabricated from Al-Li alloys. This NASA Marshall Space Flight Center (MSFC) sponsored program has been a part of a unique government / industry partnership, coordinated to develop and demonstrate near-net forging technology. The objective of this program was to demonstrate scale-up of the near-net forging process. This objective was successfully achieved by fabricating four integrally stiffened, 170- inch diameter by 20-inch tall, Al-Li alloy 2195, Y-ring adapters. Initially, two 2195 Al-Li ingots were converted and back extruded to produce four cylindrical blockers. Conventional ring rolling of the blockers was performed to produce ring preforms, which were then contour ring rolled to produce

  19. CHARACTERIZATION OF NEW TOOL STEEL FOR ALUMINUM EXTRUSION DIES

    Directory of Open Access Journals (Sweden)

    José Britti Bacalhau

    2014-06-01

    Full Text Available Aluminum extrusion dies are an important segment of application on industrial tools steels, which are manufactured in steels based on AISI H13 steel. The main properties of steels applied to extrusion dies are: wear resistance, impact resistance and tempering resistance. The present work discusses the characteristics of a newly developed hot work steel to be used on aluminum extrusion dies. The effects of Cr and Mo contents with respect to tempering resistance and the Al addition on the nitriding response have been evaluated. From forged steel bars, Charpy impact test and characterization via EPMA have been conducted. The proposed contents of Cr, Mo, and Al have attributed to the new VEX grade a much better tempering resistance than H13, as well as a deeper and harder nitrided layer. Due to the unique characteristics, this new steel provides an interesting alternative to the aluminum extrusion companies to increase their competitiveness.

  20. 27 CFR 447.22 - Forgings, castings, and machined bodies.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Forgings, castings, and... IMPLEMENTS OF WAR The U.S. Munitions Import List § 447.22 Forgings, castings, and machined bodies. Articles on the U.S. Munitions Import List include articles in a partially completed state (such as forgings...

  1. The State of the Art in Cold Forging Lubrication

    DEFF Research Database (Denmark)

    Bay, Niels

    1994-01-01

    The manufature of components in steel, aluminium and copper alloys by cold forging production has increased ever since the 1950's. Typical processes are forward rod extrusion and backward can extrusion, upsetting, ironing, tube extrusion and radial extrusion. The tribological conditions in cold...... forging are extremely severe due to large surface expansion and normal pressure in the tool/workpiece interface combined with elevated tool temperatures. Except for the more simple cold forging operations successful production therefore requires advanced lubrication systems. The present paper gives...... a detailed description of the state of art for lubricant systems for cold forging of C-steels and low alloy steels as well as aluminium alloys including all the basic operations such as cleaning of the slugs, application of eventual conversion coating and lubrication. As regards cold forging of steel...

  2. Instant forgedUI starter

    CERN Document Server

    Luiz, Joseandro

    2013-01-01

    Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks.The book is a Starter guide to learning ForgedUI. This book will start by unfolding the installation and creating a simple application using Titanium and ForgedUI, followed by taking you through the features to model an engaging UI and generate multi-platform code with Titanium, while covering the best design practice for Apple and Android application development. Last but not least, you will also come across the available resources where you can

  3. An empirical model for friction in cold forging

    DEFF Research Database (Denmark)

    Bay, Niels; Eriksen, Morten; Tan, Xincai

    2002-01-01

    With a system of simulative tribology tests for cold forging the friction stress for aluminum, steel and stainless steel provided with typical lubricants for cold forging has been determined for varying normal pressure, surface expansion, sliding length and tool/work piece interface temperature...... of normal pressure and tool/work piece interface temperature. The model is verified by process testing measuring friction at varying reductions in cold forward rod extrusion. KEY WORDS: empirical friction model, cold forging, simulative friction tests....

  4. 40 CFR 467.40 - Applicability; description of the forging subcategory.

    Science.gov (United States)

    2010-07-01

    ... forging subcategory. 467.40 Section 467.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ALUMINUM FORMING POINT SOURCE CATEGORY Forging Subcategory § 467.40 Applicability; description of the forging subcategory. This subpart applies to discharges of...

  5. A-508 class 3 forgings for pressure vessels

    International Nuclear Information System (INIS)

    Comon, J.

    1977-01-01

    The manufacture of the forged parts of the first PWR nuclear pressure vessel installed in France started in the Creusot-Loire's Forge Plant in 1961. Since this date, more than 300 forgings of this type were delivered (flanges, rings, zones, and nozzles). The major part of these forgings were made of Mn, Ni, Mo steel (SA 508 class 3). They represent a population large and homogeneous enough to attempt a statistical analysis of chemical and mechanical test results. The aim of this analysis was double: (1) a better knowledge of the scattering of the results and a better estimate of what can be introduced or accepted in a specification, and (2) the setting up of correlations existing between these results, particularly between chemical analysis and mechanical test results. In addition to this statistical analysis concerning industrial results, several laboratory studies are presented, giving a more complete characterization of SA 508 class 3. All these results form a very complete documentation showing that SA 508 class 3 steel is suitable for the manufacture of large forged vessels requiring a high degree of reliability

  6. Effect of Laser Preheating AISI 4140 Specimens for Micro-Forging

    Directory of Open Access Journals (Sweden)

    Jung C.

    2017-06-01

    Full Text Available Many high performance and permanent service parts require suitable material characteristics-high fatigue strength is one of the most important characteristics. For this reason, surface treatment processes are essential to increase the material performance and avoid the use of costly ineffective material. There exist various surface treatment processes for various applications. Each process has advantages and disadvantages and hybridization can solve various problems. The micro-forging process delivers a controlled and uniform surface hardness, but the depth of the forged surface is limited. On the other hand, laser heat treatment can increase the hardness drastically, but the surface may become brittle, which reduces the fatigue life. Laser-assisted micro-forging is a novel hybrid process of laser heat treatment and micro-forging that has the potential to increase the forging depth and relax the stress caused by the high temperature of the forging process.

  7. 48 CFR 252.225-7025 - Restriction on acquisition of forgings.

    Science.gov (United States)

    2010-10-01

    ... of forgings. 252.225-7025 Section 252.225-7025 Federal Acquisition Regulations System DEFENSE... CLAUSES Text of Provisions And Clauses 252.225-7025 Restriction on acquisition of forgings. As prescribed in 225.7102-4, use the following clause: Restriction on Acquisition of Forgings (DEC 2009) (a...

  8. Experimental and numerical research on forging with torsion

    Science.gov (United States)

    Petrov, Mikhail A.; Subich, Vadim N.; Petrov, Pavel A.

    2017-10-01

    Increasing the efficiency of the technological operations of blank production is closely related to the computer-aided technologies (CAx). On the one hand, the practical result represents reality exactly. On the other hand, the development procedure of new process development demands unrestricted resources, which are limited on the SMEs. The tools of CAx were successfully applied for development of new process of forging with torsion and result analysis as well. It was shown, that the theoretical calculations find the confirmation both in praxis and during numerical simulation. The mostly used constructional materials were under study. The torque angles were stated. The simulated results were evaluated by experimental procedure.

  9. CAD system of design and engineering provision of die forming of compressor blades for aircraft engines

    Science.gov (United States)

    Khaimovich, I. N.

    2017-10-01

    The articles provides the calculation algorithms for blank design and die forming fitting to produce the compressor blades for aircraft engines. The design system proposed in the article allows generating drafts of trimming and reducing dies automatically, leading to significant reduction of work preparation time. The detailed analysis of the blade structural elements features was carried out, the taken limitations and technological solutions allowed forming generalized algorithms of forming parting stamp face over the entire circuit of the engraving for different configurations of die forgings. The author worked out the algorithms and programs to calculate three dimensional point locations describing the configuration of die cavity. As a result the author obtained the generic mathematical model of final die block in the form of three-dimensional array of base points. This model is the base for creation of engineering documentation of technological equipment and means of its control.

  10. On the quench sensitivity of 7010 aluminum alloy forgings in the overaged condition

    Energy Technology Data Exchange (ETDEWEB)

    Tiryakioğlu, Murat, E-mail: m.tiryakioglu@unf.edu [School of Engineering, University of North Florida, Jacksonville, FL 32224 (United States); Robinson, Jeremy S. [Department of Mechanical, Aeronautical and Biomedical Engineering, University of Limerick, Limerick (Ireland); Eason, Paul D. [School of Engineering, University of North Florida, Jacksonville, FL 32224 (United States)

    2014-11-17

    The quench sensitivity of an overaged 7010 alloy forging was characterized by tensile and Vickers hardness tests, as well as scanning electron microscopy. Longitudinal tensile specimens, excised from a rectilinear open die forging were cooled from the solution treatment temperature following thirty-two different cooling paths including interrupted and delayed quenches. SEM analysis of the microstructure showed that quench precipitates were (i) Al{sub 2}CuMg (S) which nucleated heterogeneously on grain boundaries and (ii) Mg(Zn,Cu,Al){sub 2} (η) on grain boundaries, dispersoid bands, subgrain boundaries as well as in the aluminum matrix. The quench sensitivity of the alloy's yield strength and Vickers hardness was modeled simultaneously by quadruple-C curves, using an improved methodology for Quench Factor Analysis. The four C-curves used in the model represented loss of solute by (i) precipitation of S on grain boundaries, and precipitation of η (ii) on grain boundaries and dispersoid bands, (iii) on subgrain boundaries and (iv) in the matrix. The model yielded coefficient of determination (R{sup 2}) values of 0.967 and 0.974 for yield strength and Vickers hardness, respectively. The model and the implications of the results are discussed in this paper.

  11. Ultra-large size austenitic stainless steel forgings for fast breeder reactor 'Monju'

    International Nuclear Information System (INIS)

    Tsukada, Hisashi; Suzuki, Komei; Sato, Ikuo; Miura, Ritsu.

    1988-01-01

    The large SUS 304 austenitic stainless steel forgings for the reactor vessel of the prototype FBR 'Monju' of 280 MWe output were successfully manufactured. The reactor vessel contains the heart of the reactor and sodium coolant at 530 deg C, and its inside diameter is about 7 m, and height is about 18 m. It is composed of 12 large forgings, that is, very thick flanges and shalls made by ring forging and an end plate made by disk forging and hot forming, using a special press machine. The manufacture of these large forgings utilized the results of the basic test on the material properties in high temperature environment and the effect that the manufacturing factors exert on the material properties and the results of the development of manufacturing techniques for superlarge forgings. The problems were the manufacturing techniques for the large ingots of 250 t class of high purity, the hot working techniques for stainless steel of fine grain size, the forging techniques for superlarge rings and disks, and the machining techniques of high precision for particularly large diameter, thin wall rings. The manufacture of these large stainless steel forgings is reported. (Kako, I.)

  12. 77 FR 14445 - Application for a License To Export Steel Forging

    Science.gov (United States)

    2012-03-09

    ... NUCLEAR REGULATORY COMMISSION Application for a License To Export Steel Forging Pursuant to 10 CFR 110.70(b) ``Public Notice of Receipt of an Application,'' please take notice that the Nuclear... head steel February 7, 2012 forging. forging will be XR175 machined into the 11005983 finished vessel...

  13. Mannes of Forging and Perspectives of Knuckle Joint Presses Modernization

    Directory of Open Access Journals (Sweden)

    A. A. Antsifirov

    2014-01-01

    Full Text Available The article raises an issue to enhance technological forging capabilities on the known knuckle joint presses. It provides an illustrated overview of main design types of presses with crank-knuckle, toggle-knuckle, and knuckle joint mechanisms. The article also shows the advantages of the modernization way and improvement just of the active press equipment in terms of quality-to-price ratio, for example, as compared to the similar new foreign press equipment.It gives an overview of features, which provide forging processes owing to kinetic energy accumulated with the moving parts of the known designs of the knuckle joint presses depending on the drive actuating mechanism. Focused attention is drawn to forging on the knuckle joint presses for a time of contact with a work piece to be comparable with the duration of the work piece deformation process on hydraulic forging hammers. This allows us to forge thin-wall products with process automation compared to the forging hammers.Analysis of accumulating processes of kinetic energy by the moving parts of the knuckle joint presses has shown that presses driven by hydraulic cylinders or two screw hydraulic cylinder are the most optimal for technological operations as evidenced by references to domestic and foreign invention certificates and patents. The article presents disadvantages of forging on presses with hydraulic or pneumatic drive. It is a dependence of the deformation force, caused, mainly, by a force of the drive cylinder. The article gives linear movement rate quantities of press moving members depending on the drives of the actuating mechanism. Based on the above analysis of the features to manufacture work pieces on the knuckle joint presses, the article gives the rationale for the relevance of forging in a short period of time, provided that the moving parts of the press accumulate the required kinetic energy. This can be achieved only through modernization and improvement of forging

  14. Optical Forging of Graphene into Three-Dimensional Shapes.

    Science.gov (United States)

    Johansson, Andreas; Myllyperkiö, Pasi; Koskinen, Pekka; Aumanen, Jukka; Koivistoinen, Juha; Tsai, Hung-Chieh; Chen, Chia-Hao; Chang, Lo-Yueh; Hiltunen, Vesa-Matti; Manninen, Jyrki J; Woon, Wei Yen; Pettersson, Mika

    2017-10-11

    Atomically thin materials, such as graphene, are the ultimate building blocks for nanoscale devices. But although their synthesis and handling today are routine, all efforts thus far have been restricted to flat natural geometries, since the means to control their three-dimensional (3D) morphology has remained elusive. Here we show that, just as a blacksmith uses a hammer to forge a metal sheet into 3D shapes, a pulsed laser beam can forge a graphene sheet into controlled 3D shapes in the nanoscale. The forging mechanism is based on laser-induced local expansion of graphene, as confirmed by computer simulations using thin sheet elasticity theory.

  15. Development of high purity large forgings for nuclear power plants

    International Nuclear Information System (INIS)

    Tanaka, Yasuhiko; Sato, Ikuo

    2011-01-01

    The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

  16. Development of high purity large forgings for nuclear power plants

    Science.gov (United States)

    Tanaka, Yasuhiko; Sato, Ikuo

    2011-10-01

    The recent increase in the size of energy plants has been supported by the development of manufacturing technology for high purity large forgings for the key components of the plant. To assure the reliability and performance of the large forgings, refining technology to make high purity steels, casting technology for gigantic ingots, forging technology to homogenize the material and consolidate porosity are essential, together with the required heat treatment and machining technologies. To meet these needs, the double degassing method to reduce impurities, multi-pouring methods to cast the gigantic ingots, vacuum carbon deoxidization, the warm forging process and related technologies have been developed and further improved. Furthermore, melting facilities including vacuum induction melting and electro slag re-melting furnaces have been installed. By using these technologies and equipment, large forgings have been manufactured and shipped to customers. These technologies have also been applied to the manufacture of austenitic steel vessel components of the fast breeder reactors and components for fusion experiments.

  17. Development of Oxide Dispersion Strengthened (ODS) Ferritic Steel Through Powder Forging

    Science.gov (United States)

    Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

    2017-04-01

    Oxide dispersion strengthened (ODS) ferritic steels are candidates for cladding tubes in fast breeder nuclear reactors. In this study, an 18%Cr ODS ferritic steel was prepared through powder forging route. Elemental powders with a nominal composition of Fe-18Cr-2 W-0.2Ti (composition in wt.%) with 0 and 0.35% yttria were prepared by mechanical alloying in a Simoloyer attritor under argon atmosphere. The alloyed powders were heated in a mild steel can to 1473 K under flowing hydrogen atmosphere. The can was then hot forged. Steps of sealing, degassing and evacuation are eliminated by using powder forging. Heating ODS powder in hydrogen atmosphere ensures good bonding between alloy powders. A dense ODS alloy with an attractive combination of strength and ductility was obtained after re-forging. On testing at 973 K, a loss in ductility was observed in yttria-containing alloy. The strength and ductility increased with increase in strain rate at 973 K. Reasons for this are discussed. The ODS alloy exhibited a recrystallized microstructure which is difficult to achieve by extrusion. No prior particle boundaries were observed after forging. The forged compacts exhibited isotropic mechanical properties. It is suggested that powder forging may offer several advantages over the traditional extrusion/HIP routes for fabrication of ODS alloys.

  18. Medium carbon vanadium micro alloyed steels for drop forging

    International Nuclear Information System (INIS)

    Jeszensky, Gabor; Plaut, Ronald Lesley

    1992-01-01

    Growing competitiveness of alternative manufacturing routes requires cost minimization in the production of drop forged components. The authors analyse the potential of medium carbon, vanadium microalloyed steels for drop forging. Laboratory and industrial experiments have been carried out emphasizing deformation and temperature cycles, strain rates and dwell times showing a typical processing path, associated mechanical properties and corresponding microstructures. The steels the required levels of mechanical properties on cooling after forging, eliminating subsequent heat treatment. The machinability of V-microalloyed steels is also improved when compared with plain medium carbon steels. (author)

  19. The investigation of the FM heavy forging process by the Moiré method. Part II: Consecutive reduction results

    NARCIS (Netherlands)

    Wang, S.L.; Cao, Q.X.

    1994-01-01

    In part I of this work (preceding paper), single-reduction results on the FM forging process were reported. In the work reported in this paper, the cavity closing laws of the consecutive reduction process were investigated, the appropriate turn-over and feed procedure being obtained, along with the

  20. Study on isothermal precision forging process of rare earth intensifying magnesium alloy

    International Nuclear Information System (INIS)

    Shan, Debin; Xu, Wenchen; Han, Xiuzhu; Huang, Xiaolei

    2012-01-01

    A three dimensional rigid-plastic finite element model is established to simulate the isothermal precision forging process of the magnesium alloy bracket based on DEFORM 3D in order to analyze the material flow rule and determine the forging process scheme. Some problems such as underfilling and too large forging pressure are predicted and resolved through optimizing the shapes of the billet successfully. Compared to the initial microstructure, the isothermal-forged microstructure of the alloy refines obviously and amounts of secondary phases precipitate on the matrix during isothermal forging process. In subsequent ageing process, large quantities of secondary phases precipitate from α-Mg matrix with increasing ageing time. The optimal comprehensive mechanical properties of the alloy have been obtained after aged at 473 K, 63 h with the ultimate tensile strength, tensile yield strength and elongation 380 MPa, 243 MPa and 4.07% respectively, which shows good potential for application of isothermal forging process of rare earth intensifying magnesium alloy.

  1. Sensitivity analysis and optimization algorithms for 3D forging process design

    International Nuclear Information System (INIS)

    Do, T.T.; Fourment, L.; Laroussi, M.

    2004-01-01

    This paper presents several approaches for preform shape optimization in 3D forging. The process simulation is carried out using the FORGE3 registered finite element software, and the optimization problem regards the shape of initial axisymmetrical preforms. Several objective functions are considered, like the forging energy, the forging force or a surface defect criterion. Both deterministic and stochastic optimization algorithms are tested for 3D applications. The deterministic approach uses the sensitivity analysis that provides the gradient of the objective function. It is obtained by the adjoint-state method and semi-analytical differentiation. The study of stochastic approaches aims at comparing genetic algorithms and evolution strategies. Numerical results show the feasibility of such approaches, i.e. the achieving of satisfactory solutions within a limited number of 3D simulations, less than fifty. For a more industrial problem, the forging of a gear, encouraging optimization results are obtained

  2. High yttria ferritic ODS steels through powder forging

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Deepak [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Prakash, Ujjwal, E-mail: ujwalfmt@iitr.ac.in [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Dabhade, Vikram V. [Department of Metallurgical and Materials Engineering, I.I.T-Roorkee, Uttarakhand 247667 (India); Laha, K.; Sakthivel, T. [Mechanical Metallurgy Group, IGCAR, Kalpakkam, Tamilnadu 603102 (India)

    2017-05-15

    Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y{sub 2}O{sub 3} (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility. - Highlights: •ODS steels with yttria contents beyond the conventional limit of 0.5 wt% were fabricated by powder forging in a hydrogen atmosphere. •All the alloys exhibited significant ductility. •This may be attributed to improved inter-particle bonding due to reduction of surface oxides by hydrogen. •Strength in excess of 300 MPa was obtained at 973 K for 0.5%, 1% and 1.5% yttria ODS alloys. •Powder forging is a promising route to fabricate ODS steels and permits development of compositions with up to 1.5% yttria.

  3. Integral forged pump casing for the primary coolant circuit of a nuclear reactor: Development in design, forging technology, and material

    International Nuclear Information System (INIS)

    Austel, W.; Korbe, H.

    1986-01-01

    Developments in the forging of large casings for primary circuit coolant pumps for light water reactors in Germany are demonstrated beginning with the multiple forging fabricated version and ending with the integral forged type. This version is the result of the joint efforts of the pump manufacturer and the forgemaster after a cost-gain evaluation and represents an optimum solution in view of its functional and economical performance and also considering the high requirements for mechanical-technological properties, including homogeneity of the material. The development from 22 NiMoCr 3 7/A 508 Class 2 to 20 MnMoNi 5 5/A 508 Class 3 and their optimization will be demonstrated. This development is based mainly on minimizing the sulfur content and on vacuum carbon deoxidation (VCD), which results in a reduction of the A-segregations, in improving fracture toughness and isotropy, and in the desired fine-grain structure

  4. Die skrifbeskouing van feministiese teoloë, in die besonder dié van Fiorenza, Brenner en Van Dijk-Hemmes – beoordeel in die lig van die gereformeerde teologie

    Directory of Open Access Journals (Sweden)

    Alta E. Swart

    2013-10-01

    Full Text Available Dit wil voorkom asof die feministiese Skrifbeskouing op die beginsel van selektiewe Skrifgesag berus. Dit beteken dat slegs dié dele in die Bybel wat met die feministiese ideologie ooreenstem, as gesaghebbend aanvaar word. Dit is veral die sogenaamde androsentriese taalgebruik wat dit vir aanhangers van hierdie benadering moeilik maak om die hele Skrif as gesaghebbend te erken. Hermeneuties vertoon hierdie benadering groot ooreenkomste met die Postmodernisme, waarin geen vaste reëls bestaan om die betekenis van tekste te bepaal nie. Gesien in die lig van die gereformeerde teologie, soos veranker in die Woord en belydenisskrifte, vertoon die feministiese teologie ernstige leemtes. Die bydraes (Skrifbeskouing van drie prominente feministiese teoloë – Fiorenza, Brenner en Van Dijk-Hemmes – word onder die loep geneem en teologies-krities geëvalueer ten einde hierdie leemtes uit te wys. It appears that the feminist view of Scripture is based on the principle of selective authority of the Scriptures, which means that only the parts of the Bible corresponding with the feminist ideology are accepted as authoritative. The use of androcentric language, in particular, makes it difficult for followers of feminism to accept the whole Bible as authoritative. Hermeneutically, their approach resembles Postmodernism, interpreting without any rules. Viewed from the paradigm of the reformed theology, which is anchored in Scripture and the articles of faith, feminist theology shows serious shortfalls. The contributions of three prominent feminist theologians – Fiorenza, Brenner and Van Dijk-Hemmes – are studied closely and evaluated critically in the light of the reformed theology, to underline these shortfalls.

  5. Application of CAD/CAE/CAM in forging process: a review

    International Nuclear Information System (INIS)

    Ahmad Baharuddin Abdullah; Hamouda, A.M.S.

    2005-01-01

    Forging can be described as the process in which metal is plastically deformed with application of huge pressure. The process not only changes the shape but also improves the properties of the forged parts due to grain size refinement. Conventionally, the empirical trial and error method has been applied, but recently there are various tools are employed to improved product quality and economic of the process. For example, Computer Aided Design (CAD) is widely used in modeling of the process, while Computer Aided Engineering (CAE) tools have been utilized in analyzing the process. To physically demonstrate the process, Computer Aided Manufacturing (CAM) such as CNC machine has been exploited. In order to improve forging process efficiency, an integrated system that combines all advantages of CAD, CAM and CAE need to be developed. This paper presents an overview of computer aided simulation such as CAD, CAE and CAM application in forging process. (Author)

  6. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  7. Calculation of recovery plasticity in multistage hot forging under isothermal conditions.

    Science.gov (United States)

    Zhbankov, Iaroslav G; Perig, Alexander V; Aliieva, Leila I

    2016-01-01

    A widely used method for hot forming steels and alloys, especially heavy forging, is the process of multistage forging with pauses between stages. The well-known effect which accompanies multistage hot forging is metal plasticity recovery in comparison with monotonic deformation. A method which takes into consideration the recovery of plasticity in pauses between hot deformations of a billet under isothermal conditions is proposed. This method allows the prediction of billet forming limits as a function of deformation during the forging stage and the duration of the pause between the stages. This method takes into account the duration of pauses between deformations and the magnitude of subdivided deformations. A hot isothermal upsetting process with pauses was calculated by the proposed method. Results of the calculations have been confirmed with experimental data.

  8. Finite element simulations and experimental investigations on ductile fracture in cold forging of aluminum alloy

    Science.gov (United States)

    Amiri, Amir; Nikpour, Amin; Saraeian, Payam

    2018-05-01

    Forging is one of the manufacturing processes of aluminium parts which has two major categories: called hot and cold forging. In the cold forging, the dimensional and geometrical accuracy of final part is high. However, fracture may occur in some aluminium alloys during the process because of less workability. Fracture in cold forging can be in the form of ductile, brittle or combination of both depending on the alloy type. There are several criteria for predicting fracture in cold forging. In this study, cold forging process of 6063 aluminium alloy for three different parts is simulated in order to predict fracture. The results of numerical simulations of Freudenthal criterion is in conformity with experimental tests.

  9. Influence of performance improvement of AP1000 nuclear island main equipment forging on manufacturing

    International Nuclear Information System (INIS)

    Liu Zhiying

    2013-01-01

    In order to comply with the 60-year design life of an AP1000 nuclear power station, higher strength and ductility requirements have been made on AP1000 nuclear island SG forgings than on CPR1000 nuclear island main equipment. In addition, bigger size of AP1000 nuclear island SG forgings increases the difficulty of manufacturing them. Insufficient recognition of these changes may cause unstable quality of forgings and possible quality problems in follow-up welding procedure. On the basis of comparison and analysis of AP1000 nuclear island SG forgings and CPR1000 nuclear island forgings, this thesis suggests clear directions for the actions we need to take. (author)

  10. Research into Oil-based Colloidal-Graphite Lubricants for Forging of Al-based Alloys

    International Nuclear Information System (INIS)

    Petrov, A.; Petrov, P.; Petrov, M.

    2011-01-01

    The presented paper describes the topical problem in metal forging production. It deals with the choice of an optimal lubricant for forging of Al-based alloys. Within the scope of the paper, the properties of several oil-based colloidal-graphite lubricants were investigated. The physicochemical and technological properties of these lubricants are presented. It was found that physicochemical properties of lubricant compositions have an influence on friction coefficient value and quality of forgings.The ring compression method was used to estimate the friction coefficient value. Hydraulic press was used for the test. The comparative analysis of the investigated lubricants was carried out. The forging quality was estimated on the basis of production test. The practical recommendations were given to choose an optimal oil-based colloidal-graphite lubricant for isothermal forging of Al-based alloy.

  11. Study on the microstructure of the different parts for new aluminum alloy forgings

    International Nuclear Information System (INIS)

    Gao Wei; Zheng Xiaojing; Wu Fu

    2014-01-01

    The mechanical properties of former aluminium alloy forgings cannot achieve technique demand. Because the component, dimension and preparation technology of new aluminum alloy have changed, the microstructure and mechanical properties of forgings are researched. It is concluded that the flowline of forgings has good continuity and uniformity, it does not have a prominent difference on microhardness of different parts. The results prove that the microstructure of forgings has good consistency. The matrix structure of forgings consists of fiber texture and equiaxed structure. The residual second phases, which are harmful to mechanical properties, are observed in the equiaxed structure. The center of equiaxed structure core zone, the edge of equiaxed structure transition zone and equiaxed structure edge zone should be focus on observing test, they are the sampling location of tensile property. (authors)

  12. 75 FR 70689 - Kaiser Aluminum Fabricated Products, LLC; Kaiser Aluminum-Greenwood Forge Division; Currently...

    Science.gov (United States)

    2010-11-18

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-70,376] Kaiser Aluminum Fabricated Products, LLC; Kaiser Aluminum- Greenwood Forge Division; Currently Known As Contech Forgings, LLC..., applicable to workers of Kaiser Aluminum Fabricated Products, LLC, Kaiser Aluminum-Greenwood Forge Division...

  13. Manufacturing and material properties of ultralarge size forgings for advanced BWRPV

    International Nuclear Information System (INIS)

    Suzuki, Komei; Sato, Ikuo; Tsukada, Hisashi

    1994-01-01

    Ultralarge size forgings for the advanced boiling water reactor (ABWR) pressure vessel as represented by the bottom petal made from a 600ton ingot have been developed. The bottom petal is a larger wall thickness ring with 10 integrated nozzles inside and outside the ring. The outer diameter is 7.8m, the height is 1.8m and the wall thickness if 1.1m in the as-forged condition. A very high purity level of P≤qslant0.003% and S≤qslant0.003% can be obtained by the application of double-refining processes to all the molten steel. The forging shows a homogeneous chemical distribution, sound internal qualities and adequate impact properties.This paper summarizes the manufacturing technique and material properties of large size forgings such as the bottom petal, the shell with integrated skirt and the bottom dome. ((orig.))

  14. Microstructure evolution and mechanical properties of a particulate reinforced magnesium matrix composites forged at elevated temperatures

    International Nuclear Information System (INIS)

    Deng, K.K.; Wu, K.; Wang, X.J.; Wu, Y.W.; Hu, X.S.; Zheng, M.Y.; Gan, W.M.; Brokmeier, H.G.

    2010-01-01

    SiCp/AZ91 magnesium matrix composite was fabricated by stir casting. The as-cast ingots were cut into cylindrical billets, and then forged at different temperatures (320, 370, 420, 470 and 520 deg. C) at a constant RAM speed of 15 mm/s with 50% reduction. The microstructure evolution of the composites during forging was investigated by optical microscope, scanning electron microscope, and transmission electron microscope. The texture of the forged composites was measured by neutron diffraction. Mechanical properties of the composite at different forging temperatures were tested by tensile tests at room temperature. It was found that a strong basal plane texture formed during forging, and the intensity of basal plane texture weakened as forging temperatures increased. The particle distribution in the composite was significantly improved by hot forging. Typical microstructures were obtained after forging at different temperatures and the composite with different microstructures offered different mechanical properties during tensile test.

  15. High yttria ferritic ODS steels through powder forging

    Science.gov (United States)

    Kumar, Deepak; Prakash, Ujjwal; Dabhade, Vikram V.; Laha, K.; Sakthivel, T.

    2017-05-01

    Oxide dispersion strengthened (ODS) steels are being developed for future nuclear reactors. ODS Fe-18%Cr-2%W-0.2%Ti steels with 0, 0.35, 0.5, 1 and 1.5% Y2O3 (all compositions in weight%) dispersion were fabricated by mechanical alloying of elemental powders. The powders were placed in a mild steel can and forged in a stream of hydrogen gas at 1473 K. The steels were forged again to final density. The strength of ODS steel increased with yttria content. Though this was accompanied by a decrease in tensile elongation, all the steels showed significant ductility. The ductility in high yttria alloys may be attributed to improved inter-particle bonding between milled powders due to reduction of surface oxides by hydrogen. This may permit development of ODS steels with yttria contents higher than the conventional limit of 0.5%. It is suggested that powder forging is a promising route to fabricate ODS steels with high yttria contents and improved ductility.

  16. 76 FR 66996 - Agency Information Collection Activities; Submission for OMB Review; Comment Request; Forging...

    Science.gov (United States)

    2011-10-28

    ... for OMB Review; Comment Request; Forging Machines ACTION: Notice. SUMMARY: The Department of Labor... collection request (ICR) titled, ``Forging Machines,'' to the Office of Management and Budget (OMB) for....218, it is mandatory for covered employers to conduct and to document periodic inspections of forging...

  17. Development and efficiency assessment of process lubrication for hot forging

    Science.gov (United States)

    Kargin, S.; Artyukh, Viktor; Ignatovich, I.; Dikareva, Varvara

    2017-10-01

    The article considers innovative technologies in testing and production of process lubricants for hot bulk forging. There were developed new compositions of eco-friendly water-graphite process lubricants for hot extrusion and forging. New approaches to efficiency assessment of process lubricants are developed and described in the following article. Laboratory and field results are presented.

  18. Production of High Quality Die Steels from Large ESR Slab Ingots

    Science.gov (United States)

    Geng, Xin; Jiang, Zhou-hua; Li, Hua-bing; Liu, Fu-bin; Li, Xing

    With the rapid development of manufacture industry in China, die steels are in great need of large slab ingot of high quality and large tonnage, such as P20, WSM718R and so on. Solidification structure and size of large slab ingots produced with conventional methods are not satisfied. However, large slab ingots manufactured by ESR process have a good solidification structure and enough section size. In the present research, the new slab ESR process was used to produce the die steels large slab ingots with the maximum size of 980×2000×3200mm. The compact and sound ingot can be manufactured by the slab ESR process. The ultra-heavy plates with the maximum thickness of 410 mm can be obtained after rolling the 49 tons ingots. Due to reducing the cogging and forging process, the ESR for large slab ingots process can increase greatly the yield and production efficiency, and evidently cut off product costs.

  19. The structural and phase state formed in construction titanium alloy by radial forging

    Energy Technology Data Exchange (ETDEWEB)

    Shlyakhova, Galina V.; Danilov, Vladimir I.; Orlova, Dina V.; Zuev, Lev B. [Institute of Strength Physics and Materials Science SB RAS, Tomsk (Russian Federation); Zavodchikov, Aleksandr S. [Perm State Technical University, Perm (Russian Federation)

    2011-07-01

    The feasibility of rod manufacture from construction titanium alloy using radial forging on a high duty machine SXK16 was investigated. The investigations were carried on for titanium rod samples using the methods of metallography, electron transmission microscophy and X-ray analysis. The results obtained are described herein. It is found that radial forging results in the formation of homogeneous fine-grained structure.Using radial forging process, high-quality items are produced. As-worked material has submicrocrystalline globular structure and an optimal α:β phase ratio. Besides, the technology is more cost-effective relative to conventional flow charts. Key words: forging, titanium alloy, fine-grain structure, substructure, pore size.

  20. Die funksie van die belydenis in die struktuur van die kerk en die ...

    African Journals Online (AJOL)

    Ter wille van die argument wat in hierdie voordrag na vore gebring word, word vier sodanige konstituerende elemente van die kerklike struktuur onderskei, te wete die belydenis, die teologie, die verkondi- ging (meer bepaald die prediking) en die kerkorde (kerkwet volgens ons terminologie). Ons gaan nou elkeen hiervan ...

  1. die rol van die unieverdedigingsmag in die onderdrukking van die

    African Journals Online (AJOL)

    agv regeringsoptrede nie.39. Siotsom. In die geskiedenis van die Unieverdedigings- mag word die gebeure random die 1914-staking oorskadu deur die Rebellie en Suid-Afrika se deelname aan die Eerste Wereldoorlog. Tog was dit 'n belangrike mylpaal in die geskiedenis van die organisasie, omdat dit sy eerste optrede ...

  2. Controlled austempering of hammer forgings aimed at pseudo normalized microstructure directly after deformation

    Directory of Open Access Journals (Sweden)

    P. Skubisz

    2017-01-01

    Full Text Available The study concerns cost-effective realization of controlled thermomechanical processing (CTMP of medium-carbon and HSLA steel aimed at producing microstructure and properties equivalent to normalized condition directly after forging. The results of theoretical and physical modeling of hot forging with subsequent heat treating adopted for industrial realization in continuous manner were verified in semi-industrial conditions of a forge plant.

  3. Improvement of mechanical properties of zirconia-toughened alumina by sinter forging

    NARCIS (Netherlands)

    He, Y.; Winnubst, Aloysius J.A.; Verweij, H.; Burggraaf, Anthonie; Burggraaf, A.J.

    1994-01-01

    ZTA powder with a composition of 85 wt% alumina/15 wt% zirconia was prepared by a gel precipitation method. Sinter forging was performed with this powder to enhance the mechanical properties of ZTA materials. The influence of processing flaws on mechanical properties of sinter forged materials and

  4. Comparative Thermal Aging Effects on PM-HIP and Forged Inconel 690

    Science.gov (United States)

    Bullens, Alexander L.; Bautista, Esteban; Jaye, Elizabeth H.; Vas, Nathaniel L.; Cain, Nathan B.; Mao, Keyou; Gandy, David W.; Wharry, Janelle P.

    2018-03-01

    This study compares thermal aging effects in Inconel 690 (IN690) produced by forging and powder metallurgy with hot isostatic pressing (PM-HIP). Isothermal aging is carried out over 400-800°C for up to 1000 h and then metallography and nanoindentation are utilized to relate grain microstructure with hardness and yield strength. The PM-HIP IN690 maintains a constant grain size through all aging conditions, while the forged IN690 exhibits limited grain growth at the highest aging temperature and longest aging time. The PM-HIP IN690 exhibits comparable mechanical integrity as the forged material throughout aging: hardness and yield strength are unchanged with 100 h aging, but increase after 1000 h aging at all temperatures. In both the PM-HIP and forged IN690, the Hall-Petch relationship for Ni-based superalloys predicts yield strength for 0-100 h aged specimens, but underestimates yield strength in the 1000 h aged specimens because of thermally induced precipitation.

  5. Forging And Milling Contribution On Residual Stresses For A Textured Biphasic Titanium Alloy

    International Nuclear Information System (INIS)

    Deleuze, C.; Fabre, A.; Barrallier, L.; Molinas, O.

    2011-01-01

    Ti-10V-2Fe-3Al is a biphasic titanium alloy (α+β) used in aeronautical applications for its mechanical properties, such as its yield strength of 1200 MPa and it weighs 40% less than steel. This alloy is particularly useful for vital parts with complex geometry, because of its high forging capability. In order to predict the capability for fatigue lifetime, the designers need to know the residual stresses. X-Ray diffraction is the main experimental technique used to determine residual stresses on the surface. In this case, stress levels are primarily influenced by the complex forging and milling process. On this alloy in particular, it may be difficult to characterize stress due to modification of the microstructure close to the surface. Results obtained by x-ray analysis depend on the correct definition of the shape of the diffraction peaks. The more precisely defined the position of the peak, the more accurately the stresses are evaluated. This paper presents a method to detect if residual stresses can be characterized by x-ray diffraction. The characterization of hardness seems to be a relevant technique to quickly analyze the capability of x-ray diffraction to determine residual stresses.

  6. Manufacturing and properties of closure head forging integrated with flange for PWR reactor pressure vessel

    International Nuclear Information System (INIS)

    Tomoharu Sasaki; Iku Kurihara; Etsuo Murai; Yasuhiko Tanaka; Koumei Suzuki

    2003-01-01

    Closure head forging (SA508, Gr.3 Cl.1) integrated with flange for PWR reactor pressure vessel has been developed. This is intended to enhance structural integrity of closure head resulted in elimination of ISI, by eliminating weld joint between closure head and flange in the conventional design. Manufacturing procedures have been established so that homogeneity and isotropy of the material properties can be assured in the closure head forging integrated with flange. Acceptance tensile and impact test specimens are taken and tested regarding the closure head forging integrated with flange as very thick and complex forgings. This paper describes the manufacturing technologies and material properties of the closure head forging integrated with flange. (orig.)

  7. Die rol van die blanke werker in die motivering van die swart werker

    Directory of Open Access Journals (Sweden)

    G. J. Oosthuizen

    1980-11-01

    Opsomming Die motivering van die Swart werker kan nie in die huidige situasie in isolasie bestudeer word nie, omdat die Blanke werker steeds in die bestuursposisie is en daarom die motivering van die Swart werker kan beïnvloed. Hierdie ondersoek was daarop gerig om die rol van die Blanke werker in die motivering van die Swart werker nader te ondersoek. Die houding en die leierskapsbenadering van die Blanke werker teenoor die Swart werker is gemeet, asook die behoeftes wat volgens die Blanke werker by die Swart werker bestaan, bevredig is, of nie bestaan nie. Die behoeftes van Swart werkers, soos deur hulleself gesien, is ook ondersoek. Ten opsigte van sekere aspekte is beduidende verskille gevind.

  8. Design and verification of thermomechanical parameters of P/M Ti6Al4V alloy forging

    Energy Technology Data Exchange (ETDEWEB)

    Wojtaszek, Marek, E-mail: mwojtasz@metal.agh.edu.pl; Śleboda, Tomasz

    2014-12-05

    Highlights: • Thermomechanical parameters of P/M Ti6Al4V alloy processing were determined. • The use of the mixture of elemental powders allows reducing manufacturing costs. • Numerical modelling allowed to elaborate favourable parameters of forging. • The industrial trials of hot forging of P/M Ti6Al4V alloy were successful. - Abstract: This work is focused on the design of technology of forging high-quality Ti6Al4V alloy by means of powder metallurgy methods. A mixture of elemental powders, with the chemical composition of that of Ti6Al4V alloy, was used as a starting material for the investigation. Powder mixtures were fully densified by hot compaction under precisely controlled conditions. The mechanical properties of the obtained compacts were examined. The mechanical behaviour of the investigated alloy powder compacts was evaluated by compression test under various thermomechanical conditions using Gleeble simulator. The microstructure of powder compacts as well as P/M alloy samples deformed in compression tests was examined. All data obtained from the experimental tests were applied as boundary conditions for numerical simulation of forging of selected forgings. Basing on the results of both plastometric tests and simulations, thermomechanical parameters of the investigated alloy forging were determined. Designed parameters of forging technology were verified by forging trials performed in industrial conditions. The quality of the obtained forgings was examined by means of computed tomography.

  9. Effect of forging process on microstructure, mechanical and corrosion properties of biodegradable Mg-1Ca alloy

    International Nuclear Information System (INIS)

    Harandi, Shervin Eslami; Hasbullah Idris, Mohd; Jafari, Hassan

    2011-01-01

    Research highlights: → Forging temperature demonstrates more pronounced effect compared to forging speed. → Precipitation of Mg 2 Ca phase at grain boundaries accelerates corrosion rate. → Forging process doesn't provide the corrosion resistance required for bone healing. -- Abstract: The performance of Mg-1Ca alloy, a biodegradable metallic material, may be improved by hot working in order that it may be of use in bone implant applications. In this study, Mg-1Ca cast alloy was preheated to different temperatures before undergoing forging process with various forging speeds. Macro- and microstructure of the samples were examined by stereo and scanning electron microscopes (SEM) equipped with energy dispersive X-ray spectroscopy (EDS), respectively. To determine the mechanical properties of the alloy, hardness value and plastic deformation ability of the samples were measured. To investigate the corrosion behaviour of the alloy, immersion and electrochemical tests were performed on the samples in simulated body fluid and the corrosion products were characterized by SEM/EDS. The results showed that increasing forging temperature decreased grain size led to improved hardness value and plastic deformation ability of the alloy, whereas no significant effect was observed by changing forging speed. Moreover, forging at higher temperatures led to an increase in the amount of Mg 2 Ca phase at grain boundaries resulted in higher corrosion rates. It can be concluded that although forging process improved the mechanical properties of the alloy, it does not satisfy the corrosion resistance criteria required for bone healing.

  10. Design and verification of thermomechanical parameters of P/M Ti6Al4V alloy forging

    International Nuclear Information System (INIS)

    Wojtaszek, Marek; Śleboda, Tomasz

    2014-01-01

    Highlights: • Thermomechanical parameters of P/M Ti6Al4V alloy processing were determined. • The use of the mixture of elemental powders allows reducing manufacturing costs. • Numerical modelling allowed to elaborate favourable parameters of forging. • The industrial trials of hot forging of P/M Ti6Al4V alloy were successful. - Abstract: This work is focused on the design of technology of forging high-quality Ti6Al4V alloy by means of powder metallurgy methods. A mixture of elemental powders, with the chemical composition of that of Ti6Al4V alloy, was used as a starting material for the investigation. Powder mixtures were fully densified by hot compaction under precisely controlled conditions. The mechanical properties of the obtained compacts were examined. The mechanical behaviour of the investigated alloy powder compacts was evaluated by compression test under various thermomechanical conditions using Gleeble simulator. The microstructure of powder compacts as well as P/M alloy samples deformed in compression tests was examined. All data obtained from the experimental tests were applied as boundary conditions for numerical simulation of forging of selected forgings. Basing on the results of both plastometric tests and simulations, thermomechanical parameters of the investigated alloy forging were determined. Designed parameters of forging technology were verified by forging trials performed in industrial conditions. The quality of the obtained forgings was examined by means of computed tomography

  11. Manufacturing of large and integral-type steel forgings for nuclear steam supply system components

    International Nuclear Information System (INIS)

    Kawaguchi, S.; Tsukada, H.; Suzuki, K.; Sato, I.; Onodera, S.

    1986-01-01

    Forgings for the reactor pressure vessel (RPV) of the pressurized heavy water reactor (PHWR) 700 MWe, which is composed of seven major parts and nozzles totaling about 965 tons, were successfully developed. These forgings are: 1. Flanges: an outside diameter of 8440 mm and a weight of 238 tons max, requiring an ingot of 570 tons. 2. Shells and torus: an outside diameter of about 8000 mm with large height. 3. Cover dome: a diameter of 6800 mm and a thickness of 460 mm, requiring a blank forging before forming of 8000 mm in diameter and 550 m thick. The material designation is 20Mn-Mo-Ni 5 5 (equivalent to SA508, Class 3). In this paper, the manufacturing of and the properties of such large and integral forgings are discussed, including an overview of manufacturing processes for ultralarge-sized forgings over the last two decades

  12. Managing Tensions And Forging Creative Synergies Between ...

    African Journals Online (AJOL)

    Managing Tensions And Forging Creative Synergies Between Indigenous And Modern Settlement Planning Concepts And Practices: Lessons For The Design And Planning For Sustainable Settlements And Built-Forms In Southern Africa.

  13. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development of energy in its 2nd year (Research and development of eco-friendly material processing system using powder lubricant type releasing agent); 1999 nendo funtai rigata junkatsuzai wo mochiita sokeizai kako eko system no kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of constructing a material processing industry consuming less energy, demanding less cost, and imposing less impact on the environment, research and development is conducted of an eco-friendly die-casting system which uses a powder lubricant type releasing agent. In the research, the effect of the die-casting metal cavity internal structure and the pressure pattern on the flowing behavior of the powder lubricant is made visible for analysis, and the mechanism of homogenous dispersion flow and injection is determined. In the research on powder type lubricants, efforts center on a calcium hydroxide-based powder lubricant, and studies are conducted about its adhesion to the metal die at high temperatures and the adhesion to and release from the metal die of molten aluminum, and the calcium hydroxide-based powder lubricant is found to work effectively. For the application of the powder lubricant to die-forging, a real forging system is experimentally built which includes a water-cooled die into which powder is injected with the die in the closed state. A powder lubricant type releasing agent GW-23 is tested for performance using this system, and then it is found that a powder lubricant prolongs the service life of dies and improves on working environments. (NEDO)

  14. Strain-induced grain growth of cryomilled nanocrystalline Al in trimodal composites during forging

    International Nuclear Information System (INIS)

    Yao, B.; Simkin, B.; Majumdar, B.; Smith, C.; Bergh, M. van den; Cho, K.; Sohn, Y.H.

    2012-01-01

    Highlights: ► Grain growth of cryomilled nanocrystalline aluminum during hot forging. ► Use of hollow cone dark field imaging technique in TEM for grain size measurement. ► Grain growth model of strain, strain rate and temperature for forging optimization. - Abstract: Grain growth of nanocrystalline aluminum ( nc Al) in trimodal Al metal-matrix-composites (MMCs) during hot forging was investigated. The nc Al phase formed through cryomilling of inert gas-atomized powders in liquid nitrogen has an average grain size down to 21 nm, exhibits excellent thermal stability. However, substantial grain growth of nc Al up to 63 nm was observed when the Al MMCs were thermo-mechanically processed even at relatively low temperatures. Grain growth of the cryomilled nc Al phase in trimodal Al MMCs after hot forging was documented with respect to temperature ranging from 175 °C to 287 °C, true strain ranging from 0.4 to 1.35 and strain rate ranging from 0.1 to 0.5 s −1 . Hollow cone dark field imaging technique was employed to provide statistically confident measurements of nc Al grain size that ranged from 21 to 63 nm. An increase in forging temperature and an increase in true strain were correlated with an increase in grain size of nc Al. Results were correlated to devise a phenomenological grain growth model for forging that takes strain, strain rate and temperature into consideration. Activation energy for the grain growth during thermo-mechanical hot-forging was determined to be 35 kJ/mol, approximately a quarter of activation energy for bulk diffusion of Al and a half of activation energy for static recrystallization.

  15. Forged Signature Distinction Using Convolutional Neural Network for Feature Extraction

    Directory of Open Access Journals (Sweden)

    Seungsoo Nam

    2018-01-01

    Full Text Available This paper proposes a dynamic verification scheme for finger-drawn signatures in smartphones. As a dynamic feature, the movement of a smartphone is recorded with accelerometer sensors in the smartphone, in addition to the moving coordinates of the signature. To extract high-level longitudinal and topological features, the proposed scheme uses a convolution neural network (CNN for feature extraction, and not as a conventional classifier. We assume that a CNN trained with forged signatures can extract effective features (called S-vector, which are common in forging activities such as hesitation and delay before drawing the complicated part. The proposed scheme also exploits an autoencoder (AE as a classifier, and the S-vector is used as the input vector to the AE. An AE has high accuracy for the one-class distinction problem such as signature verification, and is also greatly dependent on the accuracy of input data. S-vector is valuable as the input of AE, and, consequently, could lead to improved verification accuracy especially for distinguishing forged signatures. Compared to the previous work, i.e., the MLP-based finger-drawn signature verification scheme, the proposed scheme decreases the equal error rate by 13.7%, specifically, from 18.1% to 4.4%, for discriminating forged signatures.

  16. Distribution of Microstructure and Vickers Hardness in Spur Bevel Gear Formed by Cold Rotary Forging

    Directory of Open Access Journals (Sweden)

    Wuhao Zhuang

    2014-11-01

    Full Text Available Cold rotary forging is a novel metal forming technology which is widely used to produce the high performance gears. Investigating the microstructure and mechanical property of cold rotary forged gears has a great significance in improving their service performance. In this study, the grain morphology in different regions of the spur bevel gear which is processed by cold rotary forging is presented. And the distribution regulars of the grain deformation and Vickers hardness in the transverse and axial sections of the gear tooth are studied experimentally. A three-dimensional rigid-plastic FE model is developed to simulate the cold rotary forging process of a spur bevel gear under the DEFORM-3D software environment. The variation of effective strain in the spur bevel gear has been investigated so as to explain the distribution regulars of the microstructure and Vickers hardness. The results of this research thoroughly reveal the inhomogeneous deformation mechanisms in cold rotary forging of spur bevel gears and provide valuable guidelines for improving the performance of cold rotary forged spur bevel gears.

  17. 76 FR 30200 - Forging Machines; Extension of the Office of Management and Budget's (OMB) Approval of...

    Science.gov (United States)

    2011-05-24

    ...] Forging Machines; Extension of the Office of Management and Budget's (OMB) Approval of Information... extend OMB approval of the information collection requirements contained in the Forging Machines Standard... to reduce employees' risk of death or serious injury by ensuring that forging machines used by them...

  18. Effect of Forging Allowance Value on the Power Consumption of Machining Process

    Directory of Open Access Journals (Sweden)

    L. D. Mal'kova

    2015-01-01

    Full Text Available The paper aim is to develop and study possible energy-efficiency measures for machined forgings drawing on analysis of the impact of the allowance for machining and its scatter.The most sophisticated option to take into consideration the effect of the cut depth is the work-piece machining in which the forging allowance value results from the blank production.Research of power consumption was conducted for turning the cylindrical surface of 144 mm length and  1,5 33 0,5   diameter on forgings of the work-pieces "screw of steering control" made from steel 60PP. A radial dimension allowance at said cylindrical surface at six points of the five sections was sized to assess the allowance value dispersion. The size of the sample measurements at the control points was n = 600. Statistic processing has shown normal law of distribution and sample homogeneity.To analyze the results of experiments was calculated a range of allowances for this workpiece. Calculated minimum and maximum allowance per one side for rough lathing were, respectively, 0.905 mm and 1.905mm. It was found that 77% points under control lie in calculated range of allowance values. And there are no points out of the range on lesser side that proves a lack of rejects; but there are points out of the range on the bigger side, that will require additional costs for machining the specified surface, including the cost of electricity.There were three power consumption calculations based on factory- recommended duty: for processing the entire sample of forgings with an average allowance, for machining forgings allowances of which are within the recommended design range of allowance, and for processing the entire sample of forgings with a minimum value of allowance.It was found that elimination of allowance values which are outside the recommended range enables to reduce the power consumption, at least, by 6%, and the overall power consumption for processing the measured forgings

  19. Forming of bulk metallic glass microcomponents

    DEFF Research Database (Denmark)

    Wert, John A.; Thomsen, Christian; Jensen, Rune Debel

    2009-01-01

    The present article considers forward extrusion, closed-die forging and backward extrusion processes for fabrication of individual microcomponents from two bulk metallic glass (BMG) compositions: Mg60Cu30Y10 and Zr44Cu40Ag8Al8. Two types of tooling were used in the present work: relatively massive...... die sets characteristic of cold forming operations for crystalline metals and lightweight die sets adapted to the special characteristics of BMGs. In addition to demonstrating that microcomponents of several geometries can be readily fabricated from BMGs, rheological properties are combined...

  20. The Results Of The Investigation Of Thermomechanical Processing Of PM Steel

    International Nuclear Information System (INIS)

    Szczepanik, Stefan; Wisniewski, Bartosz; Krawiarz, Jerzy

    2007-01-01

    Hot die forging of PM steel is used to obtain products with high densities. The combination of this process with heat treatment of forgings directly after their forming is researched in order to reduce energy consumption in the manufacture of PM steel products. This work determined the influence of the cooling ratio directly after hot forging of PM steel samples on their structure and mechanical properties. The properties of the PM preforms were examined after sintering and after sintering, quenching into water and tempering for 1 h at 250, 350 and 550 deg. C, respectively, as well as after forging at given temperatures and cooling in water and air, respectively. Forged steel after quenching was tempered at the same temperature as the sintered samples. Good mechanical properties were obtained by hot forging at 1100 deg. C. Sintered steel with 0.6 % Cgraphite is characterized by good hardenability and is susceptible to plastic forming at 1100 - 940 deg. C. During its cooling in air a bainitic-martensitic structure is obtained, whereas after cooling in water the structure is martensitic. The properties of the forged steel are strongly dependent on deformation temperature and cooling conditions. The tensile strength of the forged PM steel with 0.6 Cgraphite after forming at 1100 deg. C is much higher than that of the same heat-treated as-sintered steel. Traditional heat treatment applied to materials after deformation at 1100 deg. C slightly increases properties in comparison to the material directly quenched into water. The best strength was 1585 ± 193 MPa, bending strength 3364 ± 142 MPa and hardness 588 ± 43 HB. Application of controlled cooling of sintered PM steel directly after close-die forging diminishes the energy consumption during product manufacture

  1. Die Region braucht die Kultur - die Kultur braucht die Region

    OpenAIRE

    Klemm, Ulrich

    1995-01-01

    Die Region braucht die Kultur - die Kultur braucht die Region. - In: Region in Aktion - oder: Region im Abseits? - Boxberg-Wölchingen : Eigenständige Regionalentwicklung Baden-Württemberg, 1995. - S. 25 f.

  2. DIE GESKIEDENIS VAN DIE PERSONEELFUNKSIE IN DIE SA ...

    African Journals Online (AJOL)

    stel (kortdiensstelsel). Met die uitbreek van die oorlog in 1939 het die. Unieverdedigingsmag uit 40% Staandemag en. 60% aktiewe Burgermag bestaan. Op 22 Sept. 1939 is magtiging aan die Aktiewe Burgermag- eenhede verleen om vrywilligers vir die duur van die oorlog te aanvaar. Agv beswaar dat die Verdedigingswet.

  3. Manufacture of large monoblock LP rotor forgings and their quality

    International Nuclear Information System (INIS)

    Suzuki, Akira; Kinoshita, Shushi; Kohno, Masayoshi; Miyakawa, Mutsuhiro; Kikuchi, Hideo

    1986-01-01

    This paper describes the manufacturing and the quality of large monoblock low pressure rotors forged from 360 ton and 420 ton ingots. To obtain good and homogenous mechanical properties throughout a rotor, a computer was used to determine the heat treatment conditions. It was found that the technique was very effective at predicting mechanical properties of a monoblock rotor. Mechanical properties including the fracture toughness and fatigue crack propagation characteristics of monoblock rotor forgings proved satisfactory. (author)

  4. Identification of forged Bank of England £20 banknotes using IR spectroscopy.

    Science.gov (United States)

    Sonnex, Emily; Almond, Matthew J; Baum, John V; Bond, John W

    2014-01-24

    Bank of England notes of £20 denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. An aim of this work was to develop a non-destructive method so that a small, compact Fourier transform infrared spectrometer (FT-IR) instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 cm(-1) arising from νasym (CO3(2-)) from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine £20 notes were observed in the ν(OH) (ca. 3500 cm(-1)), ν(C-H) (ca. 2900 cm(-1)) and ν(C=O) (ca. 1750 cm(-1)) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper. Copyright © 2013 Elsevier B.V. All rights reserved.

  5. Identification of forged Bank of England £20 banknotes using IR spectroscopy

    Science.gov (United States)

    Sonnex, Emily; Almond, Matthew J.; Baum, John V.; Bond, John W.

    2014-01-01

    Bank of England notes of £20 denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. An aim of this work was to develop a non-destructive method so that a small, compact Fourier transform infrared spectrometer (FT-IR) instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 cm-1 arising from νasym (CO32-) from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine £20 notes were observed in the ν(OH) (ca. 3500 cm-1), ν(Csbnd H) (ca. 2900 cm-1) and ν(Cdbnd O) (ca. 1750 cm-1) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper.

  6. Designing a Tool System for Lowering Friction during the Ejection of In-Die Sintered Micro Gears

    Directory of Open Access Journals (Sweden)

    Emanuele Cannella

    2017-07-01

    Full Text Available The continuous improvements in micro-forging technologies generally involve process, material, and tool design. The field assisted sintering technique (FAST is a process that makes possible the manufacture of near-net-shape components in a closed-die setup. However, the final part quality is affected by the influence of friction during the ejection phase, caused by radial expansion of the compacted and sintered powder. This paper presents the development of a pre-stressed tool system for the manufacture of micro gears made of aluminum. By using the hot isostatic pressing (HIP sintering process and different combinations of process parameters, the designed tool system was compared to a similar tool system designed without a pre-stressing strategy. The comparison between the two tool systems was based on the ejection force and part fidelity. The ejection force was measured during the tests, while the part fidelity was documented using an optical microscope and computed tomography in order to obtain a multi-scale characterization. The results showed that the use of pre-stress reduced the porosity in the gear by 40% and improved the dimensional fidelity by more than 75% compared to gears produced without pre-stress.

  7. The relationship between UT reported size and actual size of the defects in rotor forgings

    International Nuclear Information System (INIS)

    Seong, Un Hak; Kim, Jeong Tae; Park, Yun Sik

    2003-01-01

    In order to evaluate the reliability of rotor forgings, it is very important to know the actual size of the defects in the rotor forgings. The determination of the defect size requires the accurate non-destructive measurement. However, there may be some differences between the reported size with the ultrasonic non-destructive testing method and the actual size of defects. These differences may be a severe cause of errors in evaluation of rotor forgings. So, the calculated size with 'Master Curve' considering safety factor, which is usually larger than the reported size, has been used in evaluation of rotor forgings. The relation between the EFBH (Equivalent Flat Bottom Hole) size measured by non-destructive method and the actual size by destructive method in many rotors manufactured at Doosan was investigated. In this investigation 'Master Curve' compensating the differences between UT reported size and actual size of defects in our rotor forgings was obtainable. The applicability of this 'Master Curve' as a way of calculating the actual defect size was also investigated. For the evaluation of rotor forgings, it is expected that this 'Master Curve' may be used to determine the accurate actual size of defects.

  8. The relationship between UT reported size and actual size of the defects in rotor forgings

    International Nuclear Information System (INIS)

    Seong, Un Hak; Kim, Jeong Tae; Park, Yun Sik

    2003-01-01

    In order to evaluate the reliability of rotor forgings, it is very important to know the actual size of the defects in the rotor forgings. The determination of the defect size requires the accurate non-destructive measurement. However, there may be some difference between the reported size with ultrasonic non-destructive testing method and the actual size of defects. These differences may be a severe cause of errors in evaluation of rotor forgings. So, the calculated size with 'Master Curve' considering safety factor, which is usually larger than the reported size, has been used in evaluation of rotor forgings. The relation between the EFBH (Equivalent Flat Bottom Hole) size measured by non-destructive method and the actual size by destructive method in many rotors manufactured at Doosan was investigated. In this investigation, 'Master Curve' compensating the differences between UT reported size and actual size of defects in our rotor forgings was obtainable. The applicability of this 'Master Curve' as a way of calculating the actual defect size was also investigated. For the evaluation of rotor forgings, it is expected that this 'Master Curve' may be used to determine the accurate actual size of defects.

  9. Fabrication and properties of Y-Ba-Cu-O high Tc superconductor by upset-forging method

    International Nuclear Information System (INIS)

    Chang, Ho Jung; Kang, Kae Myung; Song, Jin Tae

    1990-01-01

    YBa 2 Cu 3 O 7-x oxide superconductors was fabricated by sintering process and upset-forging method, respectively, and microstructures and conduction properties were compared. There was no difference in crystal structure the (001) x-ray reflection presumably due to preferred crystal orientation of the YBa 2 Cu 3 O 7-x superconductor. Furthermore, the grain size of the 123-phase increased as the reduction ratio became larger during the upset-forging. The critical temperature for zero resistivity of both samples was almost the same, i.e., about 90K. These results have demonstrated the potential of producing YBa 2 Cu 3 O 7-x superconducting wire or tape effectively using a upset-forging method. The critical current density of the upset-forged sample, however, was lower than that of the sintered one, which fact might be ascribed to microcrack formation during fast upset-forging. (Author)

  10. Weldability Characteristics of Sintered Hot-Forged AISI 4135 Steel Produced through P/M Route by Using Pulsed Current Gas Tungsten Arc Welding

    Science.gov (United States)

    Joseph, Joby; Muthukumaran, S.; Pandey, K. S.

    2016-01-01

    Present investigation is an attempt to study the weldability characteristics of sintered hot-forged plates of AISI 4135 steel produced through powder metallurgy (P/M) route using matching filler materials of ER80S B2. Compacts of homogeneously blended elemental powders corresponding to the above steel were prepared on a universal testing machine (UTM) by taking pre-weighed powder blend with a suitable die, punch and bottom insert assembly. Indigenously developed ceramic coating was applied on the entire surface of the compacts in order to protect them from oxidation during sintering. Sintered preforms were hot forged to flat, approximately rectangular plates, welded by pulsed current gas tungsten arc welding (PCGTAW) processes with aforementioned filler materials. Microstructural, tensile and hardness evaluations revealed that PCGTAW process with low heat input could produce weldments of good quality with almost nil defects. It was established that PCGTAW joints possess improved tensile properties compared to the base metal and it was mainly attributed to lower heat input, resulting in finer fusion zone grains and higher fusion zone hardness. Thus, the present investigation opens a new and demanding field in research.

  11. Nickel-base alloy forgings for advanced high temperature power plants

    Energy Technology Data Exchange (ETDEWEB)

    Donth, B.; Diwo, A.; Blaes, N.; Bokelmann, D. [Saarschmiede GmbH Freiformschmiede, Voelklingen (Germany)

    2008-07-01

    The strong efforts to reduce the CO{sub 2} emissions lead to the demand for improved thermal efficiency of coal fired power plants. An increased thermal efficiency can be realised by higher steam temperatures and pressures in the boiler and the turbine. The European development aims for steam temperatures of 700 C which requires the development and use of new materials and also associated process technology for large components. Temperatures of 700 C and above are too high for the application of ferritic steels and therefore only Nickel-Base Alloys can fulfill the required material properties. In particular the Nickel-Base Alloy A617 is the most candidate alloy on which was focused the investigation and development in several German and European programs during the last 10 years. The goal is to verify and improve the attainable material properties and ultrasonic detectability of large Alloy 617 forgings for turbine rotors and boiler parts. For many years Saarschmiede has been manufacturing nickel and cobalt alloys and is participating the research programs by developing the manufacturing routes for large turbine rotor forgings up to a maximum diameter of 1000 mm as well as for forged tubes and valve parts for the boiler side. The experiences in manufacturing and testing of very large forgings made from nickel base alloys for 700 C steam power plants are reported. (orig.)

  12. Life prediction of l6 steel using strain-life curve and cyclic stress-strain curve by means of low cycle fatigue testing

    Science.gov (United States)

    Inamdar, Sanket; Ukhande, Manoj; Date, Prashant; Lomate, Dattaprasad; Takale, Shyam; Singh, RKP

    2017-05-01

    L6 Steel is used as die material in closed die hot forging process. This material is having some unique properties. These properties are due to its composition. Strain softening is the noticeable property of this material. Due to this in spite of cracking at high stress this material gets plastically deformed and encounters loss in time as well as money. Studies of these properties are necessary to nurture this material at fullest extent. In this paper, numerous experiments have been carried on L6 material to evaluate cyclic Stress - strain behavior as swell as strain-life behavior of the material. Low cycle fatigue test is carried out on MTS fatigue test machine at fully reverse loading condition R=-1. Also strain softening effect on forging metal forming process is explained in detail. The failed samples during low cycle fatigue test further investigated metallurgically on scanning electron microscopy. Based on this study, life estimation of hot forging die is carried out and it’s correlation with actual shop floor data is found out. This work also concludes about effect of pre-treatments like nitro-carburizing and surface coating on L6 steel material, to enhance its fatigue life to certain extent.

  13. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium research and development of energy in its 1st year (Research and development of technologies for development and manufacture of magnesium alloys for cast and forged automotive parts); 1999 nendo jidosha muke chutanko buhin magnesium gokin no kaihatsu oyobi sono kako gijutsu no kenkyu kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The research and development efforts aim to use more magnesium alloys of high performance aboard passenger cars. In the research and development of magnesium alloys for die-casting, studies are conducted about 14 kinds of alloys with their heat treatment properties improved, all based on an Mg-9%Zn-4.5%Al-0.6%Ca alloy which is expected to be excellent in resistance to heat and corrosion. In the development of forging-oriented high-strength magnesium alloys to be excellent in withstanding a hot working process, tractive characteristics superior to those of a forged 6061 aluminum material are obtained from an annealed ZK31 alloy. In the development of a high-performance heat-resistant magnesium alloy die-casting technology, it is found that an injection speed higher than that used for the existing alloys is necessary to achieve a product quality which is sound. This is true for all heat-resistant alloys except the ZAC series. Furthermore, technologies are developed which involve the forging of high-performance magnesium alloys, high-precision high-speed wet cutting, surface reforming of the environmentally friendly type, laser beam welding, etc. (NEDO)

  14. Die posisie van die Helper in die sending

    Directory of Open Access Journals (Sweden)

    I. J. van der Walt

    1972-05-01

    Full Text Available Gedurende die aanvangsjare van die sending het die helper ’n onmisbare funksie vervul. Hulle het die onherbergsame binnelande geken, waardevolle kontakpunte vir die sendelinge geopen en hulle mense geestelik help voorlig en voorberei.

  15. Identification of Forged Bank of England 20 Gbp Banknotes Using IR Spectroscopy

    Science.gov (United States)

    Sonnex, Emily

    2014-06-01

    Bank of England notes of 20 GBP denomination have been studied using infrared spectroscopy in order to generate a method to identify forged notes. A principal aim of this work was to develop a method so that a small, compact ATR FTIR instrument could be used by bank workers, police departments or others such as shop assistants to identify forged notes in a non-lab setting. The ease of use of the instrument is the key to this method, as well as the relatively low cost. The presence of a peak at 1400 wn from the blank paper section of a forged note proved to be a successful indicator of the note's illegality for the notes that we studied. Moreover, differences between the spectra of forged and genuine 20 GBP notes were observed in the ν(OH) (ca. 3500 wn), ν(C-H) (ca. 2900 wn) and ν(C=O) (ca. 1750 wn) regions of the IR spectrum recorded for the polymer film covering the holographic strip. In cases where these simple tests fail, we have shown how an infrared microscope can be used to further differentiate genuine and forged banknotes by producing infrared maps of selected areas of the note contrasting inks with background paper. Further to this, with an announcement by the Bank of England to produce polymer banknotes in the future, the work has been extended using Australian polymer banknotes to show that the method would be transferable.

  16. Reliability of the wire drawing dies

    International Nuclear Information System (INIS)

    Sheikh, A.K.; Khany, S.E.

    1993-01-01

    A wear based model is proposed for the dies used in wire drawing process. Using this wear model, it is possible to predict life of the die corresponding to a wear limit criterion. Since various quantities in the model are random in nature the resulting die life will also be random quantity characterized by an appropriate distribution. Using a probabilistic characterization of the parameters of the predictive model, Monte Carlo simulations were conducted to establish the die life distribution. To asses the sensitivity of life distribution with respect to various contributing variables (parameters), the simulation runs were conducted at different levels of these variables (parameters). It is shown that wire drawing die life is Weibull distributed. To compare the simulated results with actual time to failure, data of dies was obtained from a large wire drawing company and was compared with corresponding scenario generated by Monte Carlo simulation. Results obtained by Monte Carlo simulations were very close to the actual time to failure data. (author)

  17. die ontstaan en die ontwikkeling van die skoolkadette-stelsel in die rsa

    African Journals Online (AJOL)

    toe algemene diensplig ingestel is. Die diens- plig het intussen sy volle beslag gekry en in. Weermagkringe het die gedagte posgevat dat skoolkadette. 'n deeglike ondersoek vereis ten einde die skoolgaande seun vir sy komende nasionale diensplig te orienteer. Tydens kadetopleldlng leer die seuns al die fynere kunsles ...

  18. Achievement report for fiscal 1998 on area consortium research and development business, 1st year. Area consortium energy research and development (molding material processing eco-system using powder lubricant); 1998 nendo chiiki consortium energy kenkyu kaihatsu bun'ya. Funtai rikei junkatsuzai wo mochiita sokeizai kako eko system no kenkyu kaihatsu (dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A material processing technology demanding but low energy and cost and causing low environmental impact was developed using a powder lubricant in a closed metal die system. An inorganic powder excellent in adhesiveness as lubricant was discovered. Powder lubricants for die casting and new carbon lubricants for metal die forging were also developed. In a test in an eco-die casting system, it was found that power was better than water solution in terms of finish and energy efficiency. In the development of a metal forging system using a powder lubricant, existing graphite lubricants and new powder lubricants containing fullerene were subjected to evaluation (ring tests). Two types of graphite solutions now in use and two powder lubricants were evaluated by the ring tests, and this enabled the comprehension of powder lubricant characteristics. For the development of a die casting system requiring no lubricant, a metal die surface treatment method was found that produces a surface excellent in resisting erosion by the application of the aluminizing ion nitriding composite treatment method. In addition, wettability was compared between a PVD (physical vapor deposition)-formed nitride film and the powder lubricant constituents. The report also refers to surveys conducted for commercialization. (NEDO)

  19. 2016 Accomplishments. Tritium aging studies on stainless steel. Forging process effects on the fracture toughness properties of tritium-precharged stainless steel

    Energy Technology Data Exchange (ETDEWEB)

    Morgan, Michael J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-01-01

    Forged austenitic stainless steels are used as the materials of construction for pressure vessels designed to contain tritium at high pressure. These steels are highly resistant to tritium-assisted fracture but their resistance can depend on the details of the forging microstructure. During FY16, the effects of forging strain rate and deformation temperature on the fracture toughness properties of tritium-exposed-and-aged Type 304L stainless steel were studied. Forgings were produced from a single heat of steel using four types of production forging equipment – hydraulic press, mechanical press, screw press, and high-energy-rate forging (HERF). Each machine imparted a different nominal strain rate during the deformation. The objective of the study was to characterize the J-Integral fracture toughness properties as a function of the industrial strain rate and temperature. The second objective was to measure the effects of tritium and decay helium on toughness. Tritium and decay helium effects were measured by thermally precharging the as-forged specimens with tritium gas at 34.5 MPa and 350°C and aging for up to five years at -80°C to build-in decay helium prior to testing. The results of this study show that the fracture toughness properties of the as-forged steels vary with forging strain rate and forging temperature. The effect is largely due to yield strength as the higher-strength forgings had the lower toughness values. For non-charged specimens, fracture toughness properties were improved by forging at 871°C versus 816°C and Screw-Press forgings tended to have lower fracture toughness values than the other forgings. Tritium exposures reduced the fracture toughness values remarkably to fracture toughness values averaging 10-20% of as-forged values. However, forging strain rate and temperature had little or no effect on the fracture toughness after tritium precharging and aging. The result was confirmed by fractography which indicated that fracture modes

  20. Optimization of Thixoforging Parameters for C70S6 Steel Connecting Rods

    Science.gov (United States)

    Özkara, İsa Metin; Baydoğan, Murat

    2016-11-01

    A microalloyed steel, C70S6, with a solidification interval of 1390-1479 °C, was thixoforged in the semisolid state in a closed die at temperatures in the range 1400-1475 °C to form a 1/7 scaled-down model of a passenger vehicle connecting rod. Die design and an optimized thixoforging temperature eliminated the excessive flash and other problems during forging. Tension test samples from connecting rods thixoforged at the optimum temperature of 1440 °C exhibited nearly the same hardness, yield strength, and ultimate tensile strength as conventional hot forged samples but ductility decreased by about 45% due to grain boundary ferrite network formed during cooling from the thixoforging temperature. Thus, C70S6-grade steel can be thixoforged at 1440 °C to form flash-free connecting rods. This conclusion was also validated using FEA analysis.

  1. [A method of temperature measurement for hot forging with surface oxide based on infrared spectroscopy].

    Science.gov (United States)

    Zhang, Yu-cun; Qi, Yan-de; Fu, Xian-bin

    2012-05-01

    High temperature large forging is covered with a thick oxide during forging. It leads to a big measurement data error. In this paper, a method of measuring temperature based on infrared spectroscopy is presented. It can effectively eliminate the influence of surface oxide on the measurement of temperature. The method can measure the surface temperature and emissivity of the oxide directly using the infrared spectrum. The infrared spectrum is radiated from surface oxide of forging. Then it can derive the real temperature of hot forging covered with the oxide using the heat exchange equation. In order to greatly restrain interference spectroscopy through included in the received infrared radiation spectrum, three interference filter system was proposed, and a group of optimal gap parameter values using spectral simulation were obtained. The precision of temperature measurement was improved. The experimental results show that the method can accurately measure the surface temperature of high temperature forging covered with oxide. It meets the requirements of measurement accuracy, and the temperature measurement method is feasible according to the experiment result.

  2. Die funksie van die skeppingstradisie in die boek Jeremia

    African Journals Online (AJOL)

    gedeeites voor wat sterk ooreenkomste toon met die beskrywings van die skep pingsgebeure in die boek Jeremia. • Volgpns Von Rad (1957:144-146) het daar wel 'n groep bestaan wat belange ge- had liet by die oorlewering van die skeppingstradisies. Dit was waarskynlik die. Sadokitiese priesters wat om twee redes aan ...

  3. Die binding van die konfessie

    Directory of Open Access Journals (Sweden)

    P. J. Coetzee

    1970-05-01

    Full Text Available Ons moet waak teen twee uiterstes. Aan die een kant het die dogma as onversoenlike vyand die dogmatisme en aan die ander kant die antidogmatisme — dit hou enersyds die gevaar in van verabsolutering (oorskatting, en ander- syds die gevaar van relativisme (onderskatting.

  4. Transmission electron microscopy of Ti-12Mo-13Nb Alloy aged after heat forging

    International Nuclear Information System (INIS)

    Oliveira, Nathalia Rodrigues; Baldan, Renato; Gabriel, Sinara Borborema

    2014-01-01

    Metastable β-Ti alloys possess mechanical properties, in particular a elastic modulus that depends not only on its composition but also the applied thermomechanical treatments. These alloys require high mechanical strength and a low Young’s modulus to avoid stress shielding. Preliminary studies on the development of Ti- 13Nb-12Mo alloy showed than the better properties were obtained at aged at 500 ° C / 24 h after cold forging , whose microstructure consisted of bimodal α phase in the β matrix. In this work, Ti-12Mo-13Nb alloy was heat forged and aged at 500 deg C for 24h and the microstructure was analyzed by employing X-ray diffraction and transmission electron microscopy. According to the results, while the cold forging resulted in bimodal α phase in the β matrix, hot forging resulted in a fine and homogeneous α phase in the β matrix. (author)

  5. Modelling and Testing of Friction in Forging

    DEFF Research Database (Denmark)

    Bay, Niels

    2007-01-01

    Knowledge about friction is still limited in forging. The theoretical models applied presently for process analysis are not satisfactory compared to the advanced and detailed studies possible to carry out by plastic FEM analyses and more refined models have to be based on experimental testing...

  6. Forging Inclusive Solutions: Experiential Earth Charter Education

    Science.gov (United States)

    Hill, Linda D.

    2010-01-01

    Forging Inclusive Solutions describes the aims, methodology and outcomes of Inclusive Leadership Adventures, an experiential education curriculum for exploring the Earth Charter. Experiential education builds meaningful relationships, skills, awareness and an inclusive community based on the Earth Charter principles. When we meet people where they…

  7. Die nabyheid van die Koninkryk

    Directory of Open Access Journals (Sweden)

    W.J. Snyman

    1963-03-01

    Full Text Available Vanweë die belangrikheid daarvan volg hier ’n breër bespreking van die proefskrif van dr. Tjaart van der Walt oor die nabyheid van die Koninkryk as wat in ’n gewone resensie kan geskied. Die vraagstuk wat onder oë gesien word is so oud as die kerk en die teologie, soms minder en soms meer op die voorgrond. Tans kan gesê word, staan dit in die middelpunt. Daarby is dit nie maar ’n akademiese vraagstuk nie, maar ’n vraagstuk waarvoor elke nadenkende leser van die Skrif te staan kom.

  8. Finite element analysis for temperature distributions in a cold forging

    International Nuclear Information System (INIS)

    Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong; Kim, Sung Wook; Song, In Chul; Jeon, Byung Cheol

    2013-01-01

    In this research, the finite element method is utilized to predict the temperature distributions in a cold-forging process for a cambolt. The cambolt is mainly used as a part of a suspension system of a vehicle. The cambolt has an off-centered lobe that manipulates the vertical position of the knuckle and wheel to a slight degree. The cambolt requires certain mechanical properties, such as strength and endurance limits. Moreover, temperature is also an important factor to realize mass production and improve efficiency. However, direct measurement of temperature in a forging process is infeasible with existing technology; therefore, there is a critical need for a new technique. Accordingly, in this study, a thermo-coupled finite element method is developed for predicting the temperature distribution. The rate of energy conversion to heat for the workpiece material is determined, and the temperature distribution is analyzed throughout the forging process for a cambolt. The temperatures associated with different punch speeds are also studied, as well as the relationships between load, temperature, and punch speed. Experimental verification of the technique is presented.

  9. Finite element analysis for temperature distributions in a cold forging

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Bum; Lee, In Hwan; Cho, Hae Yong [Chungbuk National University, Cheongju (Korea, Republic of); Kim, Sung Wook [Yanbian National University, Yanbian (China); Song, In Chul; Jeon, Byung Cheol [Sunil dyfas, Jincheon (Korea, Republic of)

    2013-10-15

    In this research, the finite element method is utilized to predict the temperature distributions in a cold-forging process for a cambolt. The cambolt is mainly used as a part of a suspension system of a vehicle. The cambolt has an off-centered lobe that manipulates the vertical position of the knuckle and wheel to a slight degree. The cambolt requires certain mechanical properties, such as strength and endurance limits. Moreover, temperature is also an important factor to realize mass production and improve efficiency. However, direct measurement of temperature in a forging process is infeasible with existing technology; therefore, there is a critical need for a new technique. Accordingly, in this study, a thermo-coupled finite element method is developed for predicting the temperature distribution. The rate of energy conversion to heat for the workpiece material is determined, and the temperature distribution is analyzed throughout the forging process for a cambolt. The temperatures associated with different punch speeds are also studied, as well as the relationships between load, temperature, and punch speed. Experimental verification of the technique is presented.

  10. Effect of raw materials and hardening process on hardness of manually forged knife

    Science.gov (United States)

    Balkhaya, Suwarno

    2017-06-01

    Knives are normally made by forging process either using a machine or traditional method by means of hammering process. This present work was conducted to study the effects of steel raw materials and hardening process on the hardness of manually forged knives. The knife samples were made by traditional hammering (forging) process done by local blacksmith. Afterward, the samples were heat treated with two different hardening procedures, the first was based on the blacksmith procedure and the second was systematically done at the laboratory. The forging was done in the temperature ranged between 900-950°C, while the final temperature ranged between 650-675°C. The results showed that knives made of spring steel and heat treated in simulated condition at the laboratory obtained higher level of hardness, i.e. 62 HRC. In general, knives heat treated by local blacksmith had lower level of hardness that those obtained from simulated condition. Therefore, we concluded that the traditional knife quality in term of hardness can be improved by optimizing the heat treatment schedule.

  11. Influence of the Constitutive Flow Law in FEM Simulation of the Radial Forging Process

    Directory of Open Access Journals (Sweden)

    Olivier Pantalé

    2013-01-01

    Full Text Available Radial forging is a widely used forming process for manufacturing hollow products in transport industry. As the deformation of the workpiece, during the process, is a consequence of a large number of high-speed strokes, the Johnson-Cook constitutive law (taking into account the strain rate seems to be well adapted for representing the material behavior even if the process is performed under cold conditions. But numerous contributions concerning radial forging analysis, in the literature, are based on a simple elastic-plastic formulation. As far as we know, this assumption has yet not been validated for the radial forging process. Because of the importance of the flow law in the effectiveness of the model, our purpose in this paper is to analyze the influence of the use of an elastic-viscoplastic formulation instead of an elastic-plastic one for modeling the cold radial forging process. In this paper we have selected two different laws for the simulations: the Johnson-Cook and the Ludwik ones, and we have compared the results in terms of forging force, product's thickness, strains, stresses, and CPU time. For the presented study we use an AISI 4140 steel, and we denote a fairly good agreement between the results obtained using both laws.

  12. Die hermeneutiek van gereformeerde kerkreg

    Directory of Open Access Journals (Sweden)

    Andries le Roux du Plooy

    2012-10-01

    Full Text Available Die artikel het op die belangrikheid en noodsaaklikheid van ‘n hermeneutiek vir die gereformeerde kerkreg gefokus. Die kerkregtelike dokument wat besonderlik ter sake was, is die kerkorde van die Gereformeerde kerke in Suid-Afrika, met sy besondere band met die Dordtse kerkorde van 1618 en 1619. Agtereenvolgens is aandag gegee aan die volgende aspekte soos (1 die eiesoortige aard van ‘n kerkorde as ‘n teologiese dokument en teks, in onderskeiding van regsdokumente; (2 die aard van die hermeneutiek van kerkreg; (3 enkele teorieë oor die interpretasie of uitleg van tekste, veral regstekste en (4 normatiewe vooronderstellings en reëls vir die interpretasie en verstaan van die teks en artikels van die kerkorde asook besluite van kerklike vergaderinge. Die gevolgtrekking was dat weinig indringende navorsing gedoen is oor die saak van hermeneutiek vir kerkreg, hoewel dit noodsaaklik is. Duidelike hermeneutiese reëls is gesuggereer en verduidelik, wat sou kon meehelp dat kerke en kerklike vergaderinge die artikels van die kerkorde asook besluite en reglemente wat daarop berus het, kan interpreteer en toepas. The hermeneutics of reformed church polity. The article focused on the importance and urgency of a design for reformed hermeneutics on church polity. The Church Order referred to in the article is the Church Order of the Reformed Churches in South Africa, which are closely related to the Church Order of Dordt of 1618 and 1619. The following aspects received attention namely (1  the unique character of a Church Order, in comparison to and distinguished from legal documents and statutes; (2 the character and nature of hermeneutics of church polity; (3 theories of interpretation in the common law tradition and their relevance to church polity and (4 normative presuppositions and marks for the interpretation and understanding of the text and articles of the Church Order, as well as the resolutions of church assemblies. It was found that

  13. Tailorable Burning Behavior of Ti14 Alloy by Controlling Semi-Solid Forging Temperature.

    Science.gov (United States)

    Chen, Yongnan; Yang, Wenqing; Zhan, Haifei; Zhang, Fengying; Huo, Yazhou; Zhao, Yongqing; Song, Xuding; Gu, Yuantong

    2016-08-16

    Semi-solid processing (SSP) is a popular near-net-shape forming technology for metals, while its application is still limited in titanium alloy mainly due to its low formability. Recent works showed that SSP could effectively enhance the formability and mechanical properties of titanium alloys. The processing parameters such as temperature and forging rate/ratio, are directly correlated with the microstructure, which endow the alloy with different chemical and physical properties. Specifically, as a key structural material for the advanced aero-engine, the burn resistant performance is a crucial requirement for the burn resistant titanium alloy. Thus, this work aims to assess the burning behavior of Ti14, a kind of burn resistant alloy, as forged at different semi-solid forging temperatures. The burning characteristics of the alloy are analyzed by a series of burning tests with different burning durations, velocities, and microstructures of burned sample. The results showed that the burning process is highly dependent on the forging temperature, due to the fact that higher temperatures would result in more Ti₂Cu precipitate within grain and along grain boundaries. Such a microstructure hinders the transport of oxygen in the stable burning stage through the formation of a kind of oxygen isolation Cu-enriched layer under the burn product zone. This work suggests that the burning resistance of the alloy can be effectively tuned by controlling the temperature during the semi-solid forging process.

  14. Die invloed van grootgroeponderrig op die selfgereguleerde leer van tersiêre wiskundeleerders

    Directory of Open Access Journals (Sweden)

    Annalie

    2013-04-01

    Full Text Available elfregulering is belangrik in die ontwikkeling van lewenslange leerders, veral by voordiensonderwysers wat op hul beurt modelleerders van selfregulering in hul eie klaskamers gaan wees. Onderrig op tersiêre vlak word grootliks gekenmerk deur tradisionele onderrigmetodes vanweë die groot groepe leerders betrokke. In hierdie studie is vasgestel of ’n bepaalde grootgroeponderrigstrategie ’n invloed het op lede van groot klasgroepe se selfregulering, al dan nie. ’n Kwantitatiewe voortoets-natoets-ontwerp is gebruik waarin die studiegewoontesveld van die Studie-Oriëntasievraelys in Wiskunde aan die begin en einde van die semester ingesluit is. In ’n tweede vraelys het leerders hul belewenis van die grootgroeponderrigstrategie volgens ’n vyfpunt-Likertskaal beoordeel en ’n oopeindevraag voltooi wat ingesluit is om moontlike addisionele verklarings te bied vir die resultate wat verkry is uit die geslote vrae van die vraelys oor grootgroeponderrig. Beskrywende statistiek is gebruik om die data te interpreteer. Uit die resultate blyk dit dat daar nie ’n verbetering in leerders se selfregulering was nie. By ontleding van die oopeindevraag het dit aan die lig gekom dat verskeie aspekte van selfregulering by leerders ontbreek, soos tydsbestuur en goeie studiegewoontes, asook die bereidwilligheid om meer as net die voorgeskrewe probleme te doen.The influence of a large group teaching strategy on the self-regulated learning of tertiary mathematics learners. Self-regulation is important in developing lifelong learners, especially in the case of pre-service teachers who will soon be models of self-regulation in their own classrooms. In many instances, teaching at tertiary level is characterised by traditional teaching methods in large classes. In this study a particular large group instructional strategy was examined to determine whether it had an influence on learners’ self-regulation. A quantitative pre-test post-test design was used which

  15. On the domestically-made heavy forging for reactor pressure vessels of PWR nuclear power plant

    International Nuclear Information System (INIS)

    Pan Xiren; Zhang Chen.

    1988-01-01

    The present situation of the foreign heavy forgings for nuclear reactor pressure vessels and the heavy forgings condition which is used for the Qinshan 300MWe nuclear power plant are described. Some opinions of domestic products is proposed

  16. THE FORMING OF MAGNESIUM ALLOY FORGINGS FOR AIRCRAFT AND AUTOMOTIVE APPLICATIONS

    Directory of Open Access Journals (Sweden)

    Anna Dziubińska

    2016-09-01

    Full Text Available The paper presents the theoretical and technological aspects of forming magnesium alloy parts for aircraft and automotive applications. The main applications of magnesium alloys in the aircraft and automotive industries are discussed. In addition, the forging technology for magnesium alloys is generally described, with a particular emphasis on wrought alloys. A brief outline of the state of the art in the forging of magnesium alloys is given based on a survey of the specialist literature and the results of previous research by the authors.

  17. Manufacturing and material properties of forgings for reactor pressure vessel of high temperature engineering test reactor

    International Nuclear Information System (INIS)

    Sato, I.; Suzuki, K.

    1994-01-01

    For the reactor pressure vessel (RPV) of high temperature engineering test reactor (HTTR) which has been developed by Japan Atomic Energy Research Institute (JAERI), 2 1/4Cr-1Mo steel is used first in the world. Material confirmation test has been carried out to demonstrate good applicability of forged low Si 2 1/4Cr-1Mo steel to the RPV of HTTR. Recently, JSW has succeeded in the manufacturing of large size ring forgings and large size forged cover dome integrated with nozzles for stand pipe for the RPV. This paper describes the results of the material confirmation test as well as the manufacturing and material properties of the large forged cover dome integrated with nozzles for stand pipe. (orig.)

  18. High-Temperature Oxidation Behavior and Kinetics of Forged 12Cr-MoVW Steel

    Directory of Open Access Journals (Sweden)

    Kim Yong Hwan

    2017-06-01

    Full Text Available The oxidation kinetics of forged 12Cr-MoVW steel was investigated in an air (N2+O2 atmosphere at 873-1073 K (Δ50 K using thermogravimetric analysis. The oxidized samples were characterized using X-ray diffraction, and the surface and cross-sectional morphologies were examined using scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The forged 12Cr-MoVW steel samples exhibited parabolic behavior and a low oxidation rate compared with their as-cast counterparts. A protective oxide layer was uniformly formed at relatively low temperature (≤973 K for the forged samples, which thus exhibited better oxidation resistance than the as-cast ones. These oxides are considered solid-solution compounds such as (Fe, Cr2O3.

  19. Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus

    Directory of Open Access Journals (Sweden)

    M. M. Nel

    1990-07-01

    Full Text Available Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus word beskryf. ’n Dun bindweefselkapsel omring die lewer. Die hepatosietrangskikking vertoon as lobules, met die koorde van hepatosiete wat vanaf ’n sentrale vene uitradieer en met mekaar anastomaseer. Indiwiduele lewerlohules vertoon nie duidelike grense nie, maar enkele duidelike triades word wel in die lewer van O. mossambicus aangetref. Die hepatosiete bevat ’n enkele ronde kern met ’n duidelike nukleolus en die growwe endoplasmiese retikula kom in twee of meer rye om die kerne en teen die selgrense van die hepatosiete voor. Die ander sitoplasmiese organelle kom verspreid in die hepatosietsitoplasma voor. Die eksokriene pankreasselle is om die portale venes gesetel. Die kerne van hierdie selle is rond en is hasaal in die kubies- tot silindervormige selle gelee. ’n Goedontwikkelde growwe endoplasmiese retikulum — vesikulêr, tubulêr en sirkulêr in vorm — en sektretoriese granules wat apikaal in die sel gelee is, kom voor.

  20. Forging a unique nursing partnership with China.

    Science.gov (United States)

    Munn, Flavia

    2017-07-12

    When members of a London nursing faculty forged a learning partnership with a Chinese counterpart they likely did not expect to be discussing the benefits of using Florence Nightingale lamps to decorate hospital walls. But there is nothing ordinary about the collaboration between King's College London and Nanjing Health School.

  1. Modelling of Damage During Hot Forging of Ingots

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

    2013-01-01

    Ductile damage modelling in the ingot forging process is discussed. Advantages and disadvantages of both coupled and uncoupled ductile damage models are presented. Some uncoupled damage models are examined in greater detail regarding their applicability to different processes, where hydrostatic...

  2. Forged hollows (alloy 617) for PNP-hot gas collectors

    International Nuclear Information System (INIS)

    Hofmann, F.

    1984-01-01

    When the partners in the PNP-Project decided to manufacture components, such as gas collectors, from material of type alloy 617, the problem arose that required semi-fabricated products, especially forged hollows weighing several tons each, were not available. As VDM (Vereinigte Deutsche Metallwerke AG) had already experience in production of other semi-fabricated products of this alloy, attempts were made based on this knowledge, to develop manufacturing methods for forged hollows. The aim was to produce hollows as long as possible, and to keep the welding cost minimum. Welded seams are always critical during fabrication, as well as during later inspection under actual operating conditions. The three stage plan used to perform the above task illustrates the development aims is described

  3. die impak van metodologie op die verstaan van die nuwe testament

    African Journals Online (AJOL)

    voorbeeld eers een maal deur die bril van die vorm- en redaksiekritiek na die Evangelies gekyk het, dink jy vir altyd anders oor hulle tot- standkoming. Inderdaad, nuwe metodes lei tot nuwe perspektiewe! Dit is dan ook waar die fokus van hierdie artikel val: die impak van metodologie op die verstaan van die Nuwe ...

  4. Die vrede van Münster / Westfale en die betekenis daarvan vir die ...

    African Journals Online (AJOL)

    In die Suid-Afrikaanse kerkgeskiedenis egter is die Vrede van Münster as epogmakende gebeure tot dusver nie net in die algemeen verwaarloos nie, maar boonop is die direkte verband tussen hierdie sentrale historiese baken aan die een kant en aan die ander kant die vestiging van die VOC se verversingspos aan die ...

  5. Production of a 304 stainless steel nuclear reactor forging from a very large electroslag refined ingot

    International Nuclear Information System (INIS)

    Watkins, E.J.; Tihansky, E.L.

    1986-01-01

    A four-loop, upper barrel flange forging for a nuclear reactor was produced from what the authors believe to be the largest 304H grade stainless steel electroslag refined (ESR) ingot ever refined. The ingot was refined in a 1524-mm-diameter, ingot withdrawal-type ESR furnace using a lime-bearing slag, low-frequency a-c power, and dry air protection. Five electrodes were remelted in order to produce the desired ingot weight. The ingot was subsequently forged in a five-step operation on a 6800-metric-ton press to produce the desired barrel flange configuration. Testing of the finished machined forging revealed excellent tensile ductility, excellent ultrasonic penetrability, and good chemical uniformity with no macrosegregation. Overall quality was judged to be superior to previously produced, conventionally melted forgings

  6. die pers as bron oor die geskiedenis van die eerste vrydeidsoorlog

    African Journals Online (AJOL)

    dood agv wonde wat hy tydens die slag opgedoen het. Dit was vir die Britse volk onaanvaarbaar dat slegs twee Boere gedood is nadat daar tussen. 20 000 en 30 000 rondtes op die Boere afgevuur is. Die pers kon net nie die ware syfers publiseer nie, want dit sou na 'n onwaarheid Iyk. Het die. Britse volk egter die Boere ...

  7. Die partypolitiek en die toekoms van die Afrikaanse volkskultuur

    Directory of Open Access Journals (Sweden)

    A.P. Treurnicht

    1970-03-01

    Full Text Available Reeds in 1853 het die Zuid Afrikaan hom soos volg uitgelaat: „Dis ’n dwaling wat ons reeds meermale bestry het dat ons as Britse onderdane verplig sou wees, om die Britse nasionaliteit ons s’n te maak. Die Kolonis van Hollandse oorsprong kan geen Engelsman word nie, en moet ook geen Nederlander wil wees nie. Wanneer hy weet om sy standpunt te waardeer, dan sal hy as verligte kolonis die grondtrekke van die Engelse volkskarakter met dié van die Nederlandse harmonies leer verenig en daardeur word wat hy as Kapenaar moet word.”

  8. Highlight: Forging the new Indonesia-Canada partnership | CRDI ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    15 avr. 2016 ... Canada's Centre for International Governance Innovation and Indonesia's Centre for Strategic and International Studies organized the Indonesia-Canada Bilateral Forum, Innovation and Change: Forging the New Indonesia-Canada Partnership. IDRC co-sponsored the meeting, held May 26-27, 2015.

  9. Manufacturing involving forging of multiple objects in contact

    DEFF Research Database (Denmark)

    Nielsen, Chris Valentin; Zhang, W.; Martins, P.A.F.

    and dissimilar materials. While being plastically deformed against each other under increasing forging load, the parts dynamically develop their mutual contact interfaces. Comparisons of the final geometry as well as force-displacement curves are evaluated. The potential of simulated applications are discussed...

  10. die heidelbergse kategismus en die kategesemateriaal van die ned

    African Journals Online (AJOL)

    subjek, objek, leerstof en die metodiek van die senior kategese. Bloemfontein: Algemene Jeugkommissie Sondagskoolboekhandel. de rAAd oer ned ger kerken in Zuid AfrikA. 1921. De zevende vergadering: handelinge. 1925. De negende vergadering: handelinge. de villierS, d. W. 1957. Die Kategese in die Ned. Geref.

  11. Phased array inspection of large size forged steel parts

    Science.gov (United States)

    Dupont-Marillia, Frederic; Jahazi, Mohammad; Belanger, Pierre

    2018-04-01

    High strength forged steel requires uncompromising quality to warrant advance performance for numerous critical applications. Ultrasonic inspection is commonly used in nondestructive testing to detect cracks and other defects. In steel blocks of relatively small dimensions (at least two directions not exceeding a few centimetres), phased array inspection is a trusted method to generate images of the inside of the blocks and therefore identify and size defects. However, casting of large size forged ingots introduces changes of mechanical parameters such as grain size, the Young's modulus, the Poisson's ratio, and the chemical composition. These heterogeneities affect the wave propagation, and consequently, the reliability of ultrasonic inspection and the imaging capabilities for these blocks. In this context, a custom phased array transducer designed for a 40-ton bainitic forged ingot was investigated. Following a previous study that provided local mechanical parameters for a similar block, two-dimensional simulations were made to compute the optimal transducer parameters including the pitch, width and number of elements. It appeared that depending on the number of elements, backwall reconstruction can generate high amplitude artefacts. Indeed, the large dimensions of the simulated block introduce numerous constructive interferences from backwall reflections which may lead to important artefacts. To increase image quality, the reconstruction algorithm was adapted and promising results were observed and compared with the scattering cone filter method available in the CIVA software.

  12. Friction and wear in hot forging of steels

    International Nuclear Information System (INIS)

    Daouben, E.; Dubar, L.; Dubar, M.; Deltombe, R.; Dubois, A.; Truong-Dinh, N.; Lazzarotto, L.

    2007-01-01

    In the field of hot forging of steels, the mastering of wear phenomena enables to save cost production, especially concerning tools. Surfaces of tools are protected thanks to graphite. The existing lubrication processes are not very well known: amount and quality of lubricant, lubrication techniques have to be strongly optimized to delay wear phenomena occurrence. This optimization is linked with hot forging processes, the lubricant layers must be tested according to representative friction conditions. This paper presents the first part of a global study focused on wear phenomena encountered in hot forging of steels. The goal is the identification of reliable parameters, in order to bring knowledge and models of wear. A prototype testing stand developed in the authors' laboratory is involved in this experimental analysis. This test is called Warm and Hot Upsetting Sliding Test (WHUST). The stand is composed of a heating induction system and a servo-hydraulic system. Workpieces taken from production can be heated until 1200 deg. C. A nitrided contactor representing the tool is heated at 200 deg. C. The contactor is then coated with graphite and rubs against the workpiece, leaving a residual track on it. Friction coefficient and surface parameters on the contactor and the workpiece are the most representative test results. The surface parameters are mainly the sliding length before defects occurrence, and the amplitude of surface profile of the contactor. The developed methodology will be first presented followed by the different parts of the experimental prototype. The results of experiment show clearly different levels of performance according to different lubricants

  13. Die invloed van die neo-marxistiese kultuuranalise op die Wêreldraad van Kerke en die Gereformeerde Kerke van Nederland

    Directory of Open Access Journals (Sweden)

    J. M. Vorster

    1979-05-01

    Full Text Available Toe die studente dwarsoor die VSA en Europa in die laat sestigerjare ’n plotselinge en radikale verset openbaar het teen die bestaande orde, het hulle die deur geopen vir ’n nuwe mededinger om die hart van die Westerse kultuur. Dit is die nou reeds bekende neo-Marxisme. Sedertdien het hierdie jongeling sy voetspore op vele vlakke van die Westerse kultuur gelaat.

  14. Die regsposisie van die gemolesteerde kind 1

    Directory of Open Access Journals (Sweden)

    P.J. Schabort

    1991-03-01

    Full Text Available Hoe reik die reg uit na die seksueel gemolesteerde kind? As na die reg in wye verband gekyk word, sou dit alie wetgewing en alle gemeneregsbeginsels en alle regsprosedures insluit waardeur die Staat poog om molestering te voorkom en die gemolesteerde kind in beskerming te neem. Dit le baie wyd en sou byvoorbeeld die maatreels insluit van die Kindenvet 33 van 1960; die Wet op Egskeiding 70 van 1979; die Wet op Kindersorg 74 van 1983; die Wet op die Status van Kinders 82 van 1987 en die Wet op Bemiddeling in Sekere Egskeidingsaangeleenthede 24 van 1987. Eersdaags sal dit moontlik ook ’n Manifes vir die Regte van Kinders insluit wat vermoedelik geskoei sal wees op die W O se Konvensie vir die Regte van die Kind (1989 w a arv an die RSA tan s nog nie ’n ondertekenaar is nie.

  15. Production of A356 aluminum alloy wheels by thixo-forging combined with a low superheat casting process

    Directory of Open Access Journals (Sweden)

    Wang Shuncheng

    2013-09-01

    Full Text Available The A356 aluminum alloy wheels were produced by thixo-forging combined with a low superheat casting process. The as-cast microstructure, microstructure evolution during reheating and the mechanical properties of thixo-forged wheels made from the A356 aluminum alloy were studied. The results show that the A356 aluminum alloy round billet with fine, uniform and non-dendritic grains can be obtained when the melt is cast at 635 篊. When the round billet is reheated at 600 篊 for 60 min, the non-dendritic grains are changed into spherical ones and the round billet can be easily thixo-forged into wheels. The tensile strength, yield strength and elongation of the thixo-forged wheels with T6 heat treatment are 327.6 MPa, 228.3 MPa and 7.8%, respectively, which are higher than those of a cast wheel. It is suggested that the thixo-forging combined with the low superheat casting process is an effective technique to produce aluminum alloy wheels with high mechanical properties.

  16. strength and ductility of forged 1200 aluminum alloy reinforced

    African Journals Online (AJOL)

    eobe

    duced cylindrical shape samples, which were homogenized at 420 ... and properties of deformed materials depend on other factors ... after the surfaces were ground with emery paper of ... Figure 2: Maximum elongation of forged and annealed.

  17. Current steel forgings and their properties for steam generator of nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Sasaki, Tomoharu; Murai, Etsuo; Sato, Ikuo [Japan Steel Works Ltd., Muroran, Hokkaido (Japan). Muroran Plant; Suzuki, Kimiaki; Kusuhashi, Mikio; Tsukada, Hisashi [Japan Steel Works Ltd., Tokyo (Japan)

    2001-06-01

    On the steel forging (SF) elements for steam generator (SG) of the pressurized water type light water reactor (PWR), from a viewpoint of upgrading in their improvements of design and materials, here were described on three materials such as integrated steel forgings, high strength steel forgings, and vacuum carbon deoxidisation (VCD) steel forgings. On production of SG, by using the integrated SF, not only structural soundness of SG is upgraded, but also inspections containing inspections under production and usage become easier, to bring minimization of maintenance inspection and reduction of exposure under operation. And, in order to reduce weight of SG and upgrade seismic resistance, SA508, a Cl.3a high strength SF (620 MPa class in tensile strength) is used for some nuclear plants. Here were introduced material properties of this SF and described its chemical components and heat treatment condition. And, as a method to reduce macro- and micro-segregation of materials and to upgrade homogeneity of material property, a method combined deoxidisation of steel due to carbon monoxide reaction with crystal grain minimization due to addition of aluminum was investigated. In addition, properties of a low Si-SA508 Cl.3 steel using this method was compared with that of usual SA508 Cl.3 steel. (G.K.)

  18. Die hervertolking van die paradigma in verband met die ...

    African Journals Online (AJOL)

    Kerkorde van De Mist en die Algemene Reglement van 1816, wat onderskeidelik vir die Kaapse Kerk en die .... Een van die eerstes was Sam Freiherr von Pufendorf (1632-1694) wat in sy werk De habitu religionis ..... Koning was weer aan bewind (vgl Diepenhorst sj:74w; De Visser 1926/1927 lll:202w). 43.1 JD Janssen ...

  19. Evaluation of intergranular corrosion rate and microstructure of forged 316L round bar

    International Nuclear Information System (INIS)

    Lim, H. K.; Kim, Y. S.

    2009-01-01

    When austenitic stainless steels are heat treated in the range of 500∼850 .deg. C, the alloys are sensitized due to the formation of chromium carbide at grain boundaries and then intergranular corrosion occurs. This paper aims to evaluate the intergranular corrosion rate and microstructural change of forged 316L stainless steel. To analyze the microstructure by forging conditions, ferrite phase, sigma phase, intergranular precipitation were observed. In order to evaluate the intergranular corrosion rate. Huey test was performed by ASTM A262. On the base of microstructural observation, ferrite and sigma phases were not detected, and also intergranular precipitation was not revealed in optical microscopic observation. By ASTM A262 Practice A, step structure was shown in all forging conditions. Intergranular corrosion rate gradually increased by Huey test periods but average corrosion rate was under 0.03 mm/month

  20. Evaluation of intergranular corrosion rate and microstructure of forged 316L round bar

    Energy Technology Data Exchange (ETDEWEB)

    Lim, H. K.; Kim, Y. S. [Andong National University, Andong (Korea, Republic of)

    2009-12-15

    When austenitic stainless steels are heat treated in the range of 500{approx}850 .deg. C, the alloys are sensitized due to the formation of chromium carbide at grain boundaries and then intergranular corrosion occurs. This paper aims to evaluate the intergranular corrosion rate and microstructural change of forged 316L stainless steel. To analyze the microstructure by forging conditions, ferrite phase, sigma phase, intergranular precipitation were observed. In order to evaluate the intergranular corrosion rate. Huey test was performed by ASTM A262. On the base of microstructural observation, ferrite and sigma phases were not detected, and also intergranular precipitation was not revealed in optical microscopic observation. By ASTM A262 Practice A, step structure was shown in all forging conditions. Intergranular corrosion rate gradually increased by Huey test periods but average corrosion rate was under 0.03 mm/month.

  1. Numerical simulation of the dynamic recrystallization behaviour in hot precision forging helical gears

    Directory of Open Access Journals (Sweden)

    Feng Wei

    2015-01-01

    Full Text Available In hot precision forging helical gears, the dynamic recrystallization phenomena will occur, which affect the microstructure of the formed part and in turn decide their mechanical properties. To investigate the effect of deformation temperature on the dynamic recrystallization in hot precision forging helical gears, a three dimensional (3D finite element (FE model was created by coupling the thermo-mechanical model with the microstructure evolution model developed based on the hot compressive experimental data of 20CrMnTiH steel. The hot precision forging process was simulated and the effect laws of the deformation temperature on the microstructure evolution the formed part were investigated. The results show that the dynamic recrystallization volume fraction and the average grain sizes increased with the increasing deformation temperature and the higher deformation temperature is beneficial to dynamic recrystallization and grain refinement.

  2. The effects of composition and thermal path on hot ductility of forging steels

    Science.gov (United States)

    Connolly, Brendan M.

    This work examines the effects of composition and thermal path on the hot ductility of several forging steels with varied aluminum and nitrogen content. The primary mechanisms and controlling factors related to hot ductility are identified with a focus on the role of precipitates and segregation. The unique thermal paths and solidification structures of large cross-section forging ingots are discussed. Hot ductility testing is performed in a manner that approximates industrial conditions experienced by large cross-section forging ingots. A computer model for precipitation of aluminum nitride and vanadium nitride in austenite is presented. Industrial material is examined for comparison to experimental findings. It is found that increased aluminum and nitrogen content coarsens the as-solidified structure. The combined effects of microsegregation and uphill diffusion during deformation allow for carbide precipitation at prior austenite grain boundaries which reduces the hot ductility.

  3. Numerical simulation and experimental verification of microstructure evolution in large forged pipe used for AP1000 nuclear power plants

    International Nuclear Information System (INIS)

    Wang, Shenglong; Yang, Bin; Zhang, Mingxian; Wu, Huanchun; Peng, Jintao; Gao, Yang

    2016-01-01

    Highlights: • Establish systematically the database of 316LN stainless steel for Deform-3D. • Simulate the microstructure evolution during forging of AP1000 primary coolant pipe. • Carry out full-scale forging experiment for verification in engineering practice. • Get desirable grain size in simulation and experiment. • The variation trends of grain sizes in simulation and experiment are consistent. - Abstract: AP1000 primary coolant pipe is a large special-shaped forged pipe made of 316LN stainless steel. Due to the non-uniform temperature and deformation during its forging, coarse and fine grains usually coexist in the forged pipe, resulting in the heterogeneous microstructure and anisotropic performance. To investigate the microstructure evolution during the entire forging process, in the present research, the database of the 316LN stainless steel was established and a numerical simulation was performed. The results indicate that the middle body section of the forged pipe has an extremely uniform average grain size with the value smaller than 30 μm. The grain sizes in the ends of body sections were ranged from 30 μm to 60 μm. Boss sections have relatively homogeneous microstructure with the average grain size 30 μm to 44 μm. Furthermore, a full-scale hot forging was carried out for verification. Comparison of theoretical and experimental results showed good agreement and hence demonstrated the capabilities of the numerical simulation presented here. It is noteworthy that all grains in the workpiece were confirmed less than 180 μm, which meets the designer’s demands.

  4. Die teologiese skool in die P.U.K vir C.H.O.: met die betekenis van die teologiese skool vir die Christelike wetenskap

    Directory of Open Access Journals (Sweden)

    F. Postma

    1944-03-01

    Full Text Available Die Teologiese Skool van die Gereformeerde Kerk gedink op 29 November 1944 sy vyf-en-sewentigjarige bestaan.Die Raad en Senaat van die P.U.K. vir C.H.O. wil ook langs hierdie weg die Teologiese Skool van harte gelukwens en die versekering gee dat daar by die outoriteite van die P.U.K. ’n diepgevoelde dankbaarheid heers dat hierdie inrigting sovele jare deur onse God en Vader gedra en gespaar is.

  5. Ultrasonic phased arrays for nondestructive inspection of forgings

    International Nuclear Information System (INIS)

    Wuestenberg, H.; Rotter, B.; Klanke, H.P.; Harbecke, D.

    1993-01-01

    Ultrasonic examinations on large forgings like rotor shafts for turbines or components for nuclear reactors are carried out at various manufacturing stages and during in-service inspections. During the manufacture, most of the inspections are carried out manually. Special in-service conditions, such as those at nuclear pressure vessels, have resulted in the development of mechanized scanning equipment. Ultrasonic probes have improved, and well-adapted sound fields and pulse shapes and based on special imaging procedures for the representation of the reportable reflectors have been applied. Since the geometry of many forgings requires the use of a multitude of angles for the inspections in-service and during manufacture, phased-array probes can be used successfully. The main advantages of the phased-array concept, e.g. the generation of a multitude of angles with the typical increase of redundancy in detection and quantitative evaluation and the possibility to produce pictures of defect situations, will be described in this contribution

  6. Geologic setting of the proposed Fallon FORGE Site, Nevada: Suitability for EGS research and development

    Science.gov (United States)

    Faulds, James E.; Blankenship, Douglas; Hinz, Nicholas H.; Sabin, Andrew; Nordquist, Josh; Hickman, Stephen H.; Glen, Jonathan; Kennedy, Mack; Siler, Drew; Robinson-Tait, Ann; Williams, Colin F.; Drakos, Peter; Calvin, Wendy M.

    2015-01-01

    The proposed Fallon FORGE site lies within and adjacent to the Naval Air Station Fallon (NASF) directly southeast of the town of Fallon, Nevada, within the large basin of the Carson Sink in west-central Nevada. The site is located on two parcels that include land owned by the NASF and leased and owned by Ormat Nevada, Inc. The Carson Sink in the vicinity of the Fallon site is covered by Quaternary deposits, including alluvial fan, eolian, and lacustrine sediments. Four wells penetrate the entire Neogene section and bottom in Mesozoic basement. Late Miocene to Quaternary basin-fill sediments are 0.5 to >1 km thick and overlie Oligocene-Miocene volcanic and lesser sedimentary rocks. The volcanic section is 0.5 to 1.0 km thick and dominated by Miocene mafic lavas. The Neogene section rests nonconformably on heterogeneous Mesozoic basement, which consists of Triassic-Jurassic metamorphic rocks intruded by Cretaceous granitic plutons. The structural framework is dominated by a gently west-tilted half graben cut by moderately to steeply dipping N- to NNEstriking normal faults that dip both east and west. Quaternary faults have not been observed within the proposed FORGE site. Fallon was selected for a potential FORGE site due to its extensional tectonic setting, abundance of available data, existing infrastructure, and documented temperatures, permeability, and lithologic composition of potential reservoirs that fall within the ranges specified by DOE for FORGE. Since the early 1970s, more than 45 wells have been drilled for geothermal exploration within the area. Four exploration wells within the FORGE site are available for use in the project. Several additional wells are available for monitoring outside the central FORGE site within the NASF and Ormat lease area, including numerous temperature gradient holes. There is an existing, ten-station micro-seismic earthquake (MEQ) array that has been collecting data since 2001; the MEQ array can be expanded to encompass the

  7. De-tabooing dying control - a grounded theory study

    Science.gov (United States)

    2013-01-01

    Background Dying is inescapable yet remains a neglected issue in modern health care. The research question in this study was “what is going on in the field of dying today?” What emerged was to eventually present a grounded theory of control of dying focusing specifically on how people react in relation to issues about euthanasia and physician-assisted suicide (PAS). Methods Classic grounded theory was used to analyze interviews with 55 laypersons and health care professionals in North America and Europe, surveys on attitudes to PAS among physicians and the Swedish general public, and scientific literature, North American discussion forum websites, and news sites. Results Open awareness of the nature and timing of a patient’s death became common in health care during the 1960s in the Western world. Open dying awareness contexts can be seen as the start of a weakening of a taboo towards controlled dying called de-tabooing. The growth of the hospice movement and palliative care, but also the legalization of euthanasia and PAS in the Benelux countries, and PAS in Montana, Oregon and Washington further represents de-tabooing dying control. An attitude positioning between the taboo of dying control and a growing taboo against questioning patient autonomy and self-determination called de-paternalizing is another aspect of de-tabooing. When confronted with a taboo, people first react emotionally based on “gut feelings” - emotional positioning. This is followed by reasoning and label wrestling using euphemisms and dysphemisms - reflective positioning. Rarely is de-tabooing unconditional but enabled by stipulated positioning as in soft laws (palliative care guidelines) and hard laws (euthanasia/PAS legislation). From a global perspective three shapes of dying control emerge. First, suboptimal palliative care in closed awareness contexts seen in Asian, Islamic and Latin cultures, called closed dying. Second, palliative care and sedation therapy, but not euthanasia

  8. Numerical modeling of axi-symmetrical cold forging process by ``Pseudo Inverse Approach''

    Science.gov (United States)

    Halouani, A.; Li, Y. M.; Abbes, B.; Guo, Y. Q.

    2011-05-01

    The incremental approach is widely used for the forging process modeling, it gives good strain and stress estimation, but it is time consuming. A fast Inverse Approach (IA) has been developed for the axi-symmetric cold forging modeling [1-2]. This approach exploits maximum the knowledge of the final part's shape and the assumptions of proportional loading and simplified tool actions make the IA simulation very fast. The IA is proved very useful for the tool design and optimization because of its rapidity and good strain estimation. However, the assumptions mentioned above cannot provide good stress estimation because of neglecting the loading history. A new approach called "Pseudo Inverse Approach" (PIA) was proposed by Batoz, Guo et al.. [3] for the sheet forming modeling, which keeps the IA's advantages but gives good stress estimation by taking into consideration the loading history. Our aim is to adapt the PIA for the cold forging modeling in this paper. The main developments in PIA are resumed as follows: A few intermediate configurations are generated for the given tools' positions to consider the deformation history; the strain increment is calculated by the inverse method between the previous and actual configurations. An incremental algorithm of the plastic integration is used in PIA instead of the total constitutive law used in the IA. An example is used to show the effectiveness and limitations of the PIA for the cold forging process modeling.

  9. die sinodale verband van die nederduitse gereformeerde kerk in die

    African Journals Online (AJOL)

    Liezel

    Strauss. Die sinodale verband van die Nederduitse Gereformeerde Kerk. 122 die Vrystaatse Sinode anti-veranderingsgesind of eerder gesond-behoudend of gereformeerd-gematig? Veral as dit .... howe) in moeilike omstandighede gebring is (NG Kerk in die OVS 1865-1912:5). In 'n brief op 8 Augustus 1864 ontken Ds.

  10. Die kerkregtelike posisie van die ouderling en diaken in die ...

    African Journals Online (AJOL)

    ... drie dekades die Kerkreg gevestig as 'n selfstandige vak in die teologiese curriculum, maar ook 'n baie groot rol gespeel daarin dat die beginsels van die kerk like reg beter begryp word. Naas sy wetenskaplike bydrae word met eweveel genoegdoening gedink aan sy bcsondere persoonlikheid, sy werkvermoe, sy humor-.

  11. Stainless steel forgings for nuclear chemical plants

    International Nuclear Information System (INIS)

    1982-02-01

    This Specification covers detailed requirements for the supply of austenitic stainless steel forgings used in radioactive and corrosive areas within the Nuclear Industry. With the exception of 316S51 the materials specified are all suitable for contact with nitric acid, 316S51 being included as suitable for use in contact with sodium and other alkali metals at elevated temperatures. (author)

  12. Performance Assessment Method for a Forged Fingerprint Detection Algorithm

    Science.gov (United States)

    Shin, Yong Nyuo; Jun, In-Kyung; Kim, Hyun; Shin, Woochang

    The threat of invasion of privacy and of the illegal appropriation of information both increase with the expansion of the biometrics service environment to open systems. However, while certificates or smart cards can easily be cancelled and reissued if found to be missing, there is no way to recover the unique biometric information of an individual following a security breach. With the recognition that this threat factor may disrupt the large-scale civil service operations approaching implementation, such as electronic ID cards and e-Government systems, many agencies and vendors around the world continue to develop forged fingerprint detection technology, but no objective performance assessment method has, to date, been reported. Therefore, in this paper, we propose a methodology designed to evaluate the objective performance of the forged fingerprint detection technology that is currently attracting a great deal of attention.

  13. Plane strain forging of a niobium micro-alloyed steel

    International Nuclear Information System (INIS)

    Balancin, O.; Ferran L, G.; Rio de Janeiro Univ.

    1984-01-01

    Various termomechanical treatments were carried out on a niobium micro-alloyed steel and a low carbon steel as reference material, using an apparatus for hot phane strain forging. Control of processing variables and the presence of niobium strongly modify the austenite microstructure, which upon decomposition produces various phases such as polygonal and acicular ferrite and martensite, alone or together in variable proportions. Corresponding to this diversity of structures there is a wide variation in mechanical properties at room temperature: the initial yield point varies from 310 to 650 MPa and the reduction of area in uniaxial tension from 82 to 57% for the niobium steel. These results show that hot forging a niobium micro-alloyed steel may be a suitable manufacturing process for satisfying a wide range of specifications in a final product with low equivalent carbon. (Author) [pt

  14. Design of a forging processing route for a gas turbine compressor disc in IMI 834

    International Nuclear Information System (INIS)

    Clark, G.S.

    1993-01-01

    The microstructure in all parts of a modern gas turbine compressor disc must be carefully controlled to give the optimum balance for resistance to creep and fatigue. This is particularly true for advanced titanium alloys such as IMI834. Dynamic recrystallisation during high temperature deformation and static recrystallisation and grain growth during heat treatment, all have a profound effect on the grain structure of the disc. These processes are affected by temperature, rate of deformation and various microstructural features. These may include the size and volume fraction of primary alpha particles and current beta grain size. The construction of a computer model to simulate the forging process must therefore take all these factors into account to fully simulate the mechanical and microstructural behaviour of the material during processing. This requires a complete characterisation of the material to formulate mechanical and microstructural constitutive equations for use in a visco-plastic finite element forging model. Similarly the forging equipment must be fully characterised so that forging processes can be accurately simulated. (orig.)

  15. Near-liquidus forging, partial remelting and thixoforging of an AZ91D + Y magnesium alloy

    International Nuclear Information System (INIS)

    Zhao Zude; Chen Qiang; Hu Chuankai; Huang Shuhai; Wang Yuanqing

    2009-01-01

    A new route, near-liquidus forging plus partial remelting, has been developed for obtaining globular microstructures. Firstly, a material is formed by near-liquidus forging for obtaining a fine dendritic microstructure. Globular microstructure can be produced by reheating the material into the semi-solid temperature range for a period of time. In this paper, an AZ91D alloy with the addition of yttrium was prepared by near-liquidus forging. Microstructure evolution during partial remelting was studied at temperatures and for times. Tensile mechanical properties of thixoforged components were also determined. It is shown that the fine dendritic structure firstly evolves into a blocky structure during partial remelting. With prolonged holding time, the blocky structure disintegrates into polygonal solid particles. Prolonging time and increasing temperature promote a faster spheroidization. Good mechanical properties are obtained for the thixoforged AZ91D alloy with the addition of yttrium prepared by near-liquidus forging, with a yield strength of 160.9 MPa and a ultimate tensile strength of 301.7 MPa and a elongation to fracture of 9.734%.

  16. Current forgings and their properties for steam generator of nuclear plant

    International Nuclear Information System (INIS)

    Tsukada, Hisashi; Suzuki, Komei; Kusuhashi, Mikio; Sato, Ikuo

    1997-01-01

    Current steel forgings for steam generator (SG) of PWR plant are reviewed in the aspect of design and material improvement. The following three items are introduced. The use of integral type steel forgings for the fabrication of steam generator enhances the structural integrity and makes easier fabrication and inspection including in-service inspection. The following examples of current integral type forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced: (1) primary head integrated with nozzles, manways and supports; (2) steam drum head integrated with nozzle and handhole; (3) conical shell integrated with cylindrical sections and handholes. In order to decrease the weight of steam generator, the high strength materials such as SA508, Cl.3a steel have been adopted in some cases. The properties of this steel are introduced and the chemistry and heat treatment condition are discussed. As one of the methods to minimize the macro- and micro-segregations, the use of vacuum carbon deoxidation (VCD), i.e. deoxidization of steel by gaseous CO reaction, with addition of Al for grain refining was investigated. The properties of SA508, Cl.3 steels with Low Si content are compared with those of conventional one

  17. Current forgings and their properties for steam generator of nuclear plant

    Energy Technology Data Exchange (ETDEWEB)

    Tsukada, Hisashi; Suzuki, Komei; Kusuhashi, Mikio; Sato, Ikuo [Japan Steel Works Ltd., Muroran (Japan)

    1997-12-31

    Current steel forgings for steam generator (SG) of PWR plant are reviewed in the aspect of design and material improvement. The following three items are introduced. The use of integral type steel forgings for the fabrication of steam generator enhances the structural integrity and makes easier fabrication and inspection including in-service inspection. The following examples of current integral type forgings developed by the Japan Steel Works, Ltd. (JSW) are introduced: (1) primary head integrated with nozzles, manways and supports; (2) steam drum head integrated with nozzle and handhole; (3) conical shell integrated with cylindrical sections and handholes. In order to decrease the weight of steam generator, the high strength materials such as SA508, Cl.3a steel have been adopted in some cases. The properties of this steel are introduced and the chemistry and heat treatment condition are discussed. As one of the methods to minimize the macro- and micro-segregations, the use of vacuum carbon deoxidation (VCD), i.e. deoxidization of steel by gaseous CO reaction, with addition of Al for grain refining was investigated. The properties of SA508, Cl.3 steels with Low Si content are compared with those of conventional one.

  18. Effect of Forging Parameters on Low Cycle Fatigue Behaviour of Al/Basalt Short Fiber Metal Matrix Composites

    Directory of Open Access Journals (Sweden)

    R. Karthigeyan

    2013-01-01

    Full Text Available This paper deals with metal matrix composites (MMCs of Al 7075 alloy containing different weight percentage (2.5, 5, 7.5, and 10 basalt short fiber reinforcement and unreinforced matrix alloy. The samples were produced by the permanent stir casting technique. The casting ingots were cut into blanks to be forged in single stage and double stage, using MN press and graphite-based lubricant. The microstructures and fatigue properties of the matrix alloy and MMC samples were investigated in the as cast state and in the single and double stage forging operations. The microstructure results showed that the forged sample had a uniform distribution of the basalt short fiber throughout the specimens. Evaluation of the fatigue properties showed that the forged samples had higher values than those of the as cast counterparts. After forging, the enhancement of the fatigue strength of the matrix alloy was so significant and high in the case of 2.5 and 5.0 wt. percentage basalt short fiber reinforced MMC, and there was no enhancement in 7.5 and 10 weight percentages short fiber reinforced MMCs. The fracture damage was mainly due to decohesion at the matrix-fiber interface.

  19. Effect of forging parameters on low cycle fatigue behaviour of Al/basalt short fiber metal matrix composites.

    Science.gov (United States)

    Karthigeyan, R; Ranganath, G

    2013-01-01

    This paper deals with metal matrix composites (MMCs) of Al 7075 alloy containing different weight percentage (2.5, 5, 7.5, and 10) basalt short fiber reinforcement and unreinforced matrix alloy. The samples were produced by the permanent stir casting technique. The casting ingots were cut into blanks to be forged in single stage and double stage, using MN press and graphite-based lubricant. The microstructures and fatigue properties of the matrix alloy and MMC samples were investigated in the as cast state and in the single and double stage forging operations. The microstructure results showed that the forged sample had a uniform distribution of the basalt short fiber throughout the specimens. Evaluation of the fatigue properties showed that the forged samples had higher values than those of the as cast counterparts. After forging, the enhancement of the fatigue strength of the matrix alloy was so significant and high in the case of 2.5 and 5.0 wt. percentage basalt short fiber reinforced MMC, and there was no enhancement in 7.5 and 10 weight percentages short fiber reinforced MMCs. The fracture damage was mainly due to decohesion at the matrix-fiber interface.

  20. Die gebruik van parallelplaatreologie vir die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat

    Directory of Open Access Journals (Sweden)

    O. C. Vorster

    2005-09-01

    Full Text Available Die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat word bemoeilik deur die feit dat daar tans slegs twee metodes in gebruik is. In die eerste metode word die bepaling deur middel van oplossingsviskometrie gedoen, maar die toksisiteit van die oplosmiddel, asook die tydperk wat dit neem om die bepaling te doen, is ’n probleem. Die tweede metode word beperk deur die kompleksiteit en beskikbaarheid van die apparatuur in Suid-Afrika. In hierdie studie word ’n alternatiewe metode, gebaseer op parallelplaatreologie, voorgestel wat albei hierdie probleme oorkom en die resultate sodoende verkry, word vergelyk met dié wat met bestaande metodes verkry is.

  1. Analysis of hot rolling and hot forging effects on mechanical properties and microstructure of ZrNbMoGe alloy

    International Nuclear Information System (INIS)

    AH Ismoyo; Parikin; Bandriyana

    2014-01-01

    Research on formation technique by a combined method of rolling and forging has been carried out in order to improve the mechanical properties of ZrNbMoGe alloy to be used as fuel cladding in NPP (Nuclear Power Plant) application. The effects of rolling and forging were analyzed several tests. The tests were conducted for zirconium alloy specimen with a composition of (in % wt.) 97% Zr, 0,5% Mo, 2% Nb and 0,5% Ge, where the specimen was melted with an arc-furnace. The hot rolling and forging were conducted at 900 °C and 950 °C respectively. Hardness test was carried out by using a microhardness testing machine, while microstructure examination and crystal structure analysis were conducted with an optical microscope and an X-ray diffractometer. The results show that the hardness of the alloy increase from 141.21 HV (starting material) to 210.47 HV (hot rolled material) and 365.75 HV (hot forged material). Texturing phenomenon is clearly figured on the microstructure due to hot rolling and forging process. Analysis by diffractogram also indicates that the hot rolling and forging process has influence on the crystal orientation of dominant preferred direction in the reflection plane of (10ī1), recorded from the rise of intensity counting from about 2500 to 3000. In summary, hot forging and rolling process can change the mechanical properties (hardness and texture) and microstructure of materials. (author)

  2. The FORGE (Fate Of Repository Gases) pan European project

    International Nuclear Information System (INIS)

    Shaw, Richard

    2010-01-01

    Document available in extended abstract form only. Full text of publication follows: The multiple barrier concept is the cornerstone of all proposed schemes for underground disposal of radioactive wastes. The concept invokes a series of barriers, both engineered and natural, between the waste and the surface. Achieving this concept is the primary objective of all disposal programmes, from site appraisal and characterisation to repository design and construction. However, the performance of the repository as a whole (waste, buffer, engineering disturbed zone, host rock), and in particular its gas transport properties, are still poorly understood. Issues still to be adequately examined that relate to understanding basic processes include: dilational versus visco-capillary flow mechanisms; long-term integrity of seals, in particular gas flow along contacts; role of the EDZ as a conduit for preferential flow; laboratory to field up-scaling. Understanding gas generation and migration is thus vital in the quantitative assessment of repositories and is the focus of the research in this proposal for an integrated, multidisciplinary project. The FORGE project is a pan-European project with links to international radioactive waste management organisations, regulators and academia, specifically designed to tackle the key research issues associated with the generation and movement of repository gasses with partners from 24 organisations in 12 European countries. It is supported by funding under the European Commission FP7 Euratom programme and runs from 2009 to 2013. Of particular importance are the long-term performance of bentonite buffers, plastic clays, indurated mud-rocks and crystalline formations. Further experimental data are required to reduce uncertainty relating to the quantitative treatment of gas in performance assessment. FORGE will address these issues through a series of laboratory and field-scale experiments, including the development of new methods for up

  3. 76 FR 52313 - Heavy Forged Hand Tools (i.e., Axes & Adzes, Bars & Wedges, Hammers & Sledges, and Picks...

    Science.gov (United States)

    2011-08-22

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-570-803] Heavy Forged Hand Tools (i.e... Administration, Department of Commerce. SUMMARY: As a result of the determinations by the Department of Commerce... on heavy forged hand tools (i.e., [[Page 52314

  4. Shape optimization of metal forming and forging products using the stress equivalent static loads calculated from a virtual model

    International Nuclear Information System (INIS)

    Jang, Hwan Hak; Jeong, Seong Beom; Park, Gyung Jin

    2012-01-01

    A shape optimization is proposed to obtain the desired final shape of forming and forging products in the manufacturing process. The final shape of a forming product depends on the shape parameters of the initial blank shape. The final shape of a forging product depends on the shape parameters of the billet shape. Shape optimization can be used to determine the shape of the blank and billet to obtain the appropriate final forming and forging products. The equivalent static loads method for non linear static response structural optimization (ESLSO) is used to perform metal forming and forging optimization since nonlinear dynamic analysis is required. Stress equivalent static loads (stress ESLs) are newly defined using a virtual model by redefining the value of the material properties. The examples in this paper show that optimization using the stress ESLs is quite useful and the final shapes of a forming and forging products are identical to the desired shapes

  5. Die ontwikkeling van die bestuursmotiveringsvraelys (BMV

    Directory of Open Access Journals (Sweden)

    A. S. Engelbrecht

    1991-06-01

    Full Text Available The development of the Managerial Motivation Questionnaire (MMQ: Several criticisms of the psychometric suitability of existing measures of managerial motivation are reported in the literature. This study aimed at developing a new psychometrically sound instrument, the Managerial Motivation Questionnaire (MMQ. This was done on the basis of a comprehensive study of the literature on managerial motivation and the role-motivation theory. The preliminary MMQ was systematically shortened and refined until the final MMQ of 98 items was composed. This was based on social desirability and semantic appraisal, item analysis and factor analysis of the questionnaire. The results indicate that it was possible to develop a final MMQ that was relatively free of social desirability. It further demonstrated satsifactory internal consistencies on two samples (a = 0/90, N = 360; a = 0/91, N = 535, where all subscale items were found to be relatively pure measures of the isolated factors. Although some evidence was found providing support for the reliability of the MMQ, a need for further research on the construct validity of managerial motivation still exists. Opsomming In die literatuur word verskeie punte van kritiek teen die psigometriese geskiktheid van bestaande meetinstrumente van bestuursmotivering gerapporteer. Die doelstelling van hierdie studie was dus om aan die hand van die konseptuele omiyning van bestuursmotivering, en die rolmotiveringsteorie as algemene verwysingsraamwerk, 'n nuwe psigometries aanvaarbare meetinstrument, die Bestuursmotiveringsvraelys (BMV, te ontwikkel. Op grond van sosiale wenslikheids- en semantiese beoordeling, itemontleding en faktorontleding van die voorlopige BMV is die vraelys stelselmatig verkort en verfyn totdat die finale BMV van 98 items saamgestel is. Die resultate dui daarop dat hierdie studie wel daarin geslaag het om 'n finale BMV te ontwikkel wat relatief vry van sosiale wenslikheid is, bevredigende interne

  6. Family Health and Financial Literacy--Forging the Connection

    Science.gov (United States)

    Braun, Bonnie; Kim, Jinhee; Anderson, Elaine A.

    2009-01-01

    Families are at-risk of or experiencing a diminished quality of living and life in current economic times and difficult decisions are required. Health and financial literacy are the basis for wise personal and public decision making. Family and consumer sciences (FCS) professionals can forge connections between health and financial literacy to…

  7. Forge, Arquillian, Swarm and Spring Boot: All play and no effort makes Simon a productive boy

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    During this live coding session, Simon will shine some light on a range productivity tools that make software development a pleasure rather than a chore. Simon will live code 2 applications; a Java EE application, with JBoss Forge which uses JPA, Bean Validation, REST and Angular. We’ll test this application using Arquillian from within JBoss Forge. We’ll also show how a Java EE microservice can be developed in Forge and run using JBoss Swarm. The second application will be developed on Spring Boot and using JRebel we’ll rapidly develop and run a Spring application. Attendees will learn how to write code productively using tools designed for developers.

  8. Optimization of the Hot Forging Processing Parameters for Powder Metallurgy Fe-Cu-C Connecting Rods Based on Finite Element Simulation

    Science.gov (United States)

    Li, Fengxian; Yi, Jianhong; Eckert, Jürgen

    2017-12-01

    Powder forged connecting rods have the problem of non-uniform density distributions because of their complex geometric shape. The densification behaviors of powder metallurgy (PM) connecting rod preforms during hot forging processes play a significant role in optimizing the connecting rod quality. The deformation behaviors of a connecting rod preform, a Fe-3Cu-0.5C (wt pct) alloy compacted and sintered by the powder metallurgy route (PM Fe-Cu-C), were investigated using the finite element method, while damage and friction behaviors of the material were considered in the complicated forging process. The calculated results agree well with the experimental results. The relationship between the processing parameters of hot forging and the relative density of the connecting rod was revealed. The results showed that the relative density of the hot forged connecting rod at the central shank changed significantly compared with the relative density at the big end and at the small end. Moreover, the relative density of the connecting rod was sensitive to the processing parameters such as the forging velocity and the initial density of the preform. The optimum forging processing parameters were determined and presented by using an orthogonal design method. This work suggests that the processing parameters can be optimized to prepare a connecting rod with uniform density distribution and can help to better meet the requirements of the connecting rod industry.

  9. A two-step superplastic forging forming of semi-continuously cast AZ70 magnesium alloy

    Directory of Open Access Journals (Sweden)

    Pan Wang

    2015-03-01

    Full Text Available A two-step technology combined forging with superplastic forming has been developed to enhance the forgeability of semi-continuously cast AZ70 magnesium alloy and realize the application of the as-cast magnesium alloy in large deformation bullet shell. In the first step, fine-grained microstructure preforms that are suitable for superplastic forming were obtained by reasonably designing the size of the initial blanks with the specific height-to-diameter ratio, upsetting the blanks and subsequent annealing. In the second step, the heat treated preforms were forged into the end products at the superplastic conditions. The end products exhibit high quality surface and satisfied microstructure. Consequently, this forming technology that not only avoids complicating the material preparation but also utilizes higher strain rate superplastic provides a near net-shaped novel method on magnesium forging forming technology using as-cast billet.

  10. Forming of Hollow Shaft Forging From Titanium Alloy Ti6Al4V by Means of Rotary Compression

    Directory of Open Access Journals (Sweden)

    Tomczak J.

    2015-04-01

    Full Text Available This paper presents chosen results of theoretical-experimental works concerning forming of hollow shafts forgings from titanium alloys, which are applied in aviation industry. At the first stage of conducted analysis, the forging forming process was modeled by means of finite element method. Calculations were made using software Simufact Forming. On the basis of performed simulations optimal parameters of rotary compression process were determined. Next, experimental tests of forging forming in laboratory conditions were made. For the research needs, a forging aggregate, designed by the Authors, was used. Conducted research works confirmed the possibility of metal forming (by means of rotary compression of hollow shafts from hard workable titanium alloys. Numerous advantages of rotary compression process, make it attractive both for low series production (aircraft industry and for mass production (automotive industry.

  11. Die uitbouing van die Bybelse kanon in antieke Judaïsme en die ...

    African Journals Online (AJOL)

    31 Jul 2015 ... die oer-Christelike boodskap tot by sy Ou Testamentiese wortels, die geskrifte van Israel wat cum grano salis die 'Bybel' van die oer-Christendom geword het en die blywende verwysingspunt van die Christelike boodskap is. Erkenning. Hierdie artikel is vertaal na Afrikaans deur Prof. Jan G. van der Watt.

  12. Development of forging technology for PWR primary piping

    International Nuclear Information System (INIS)

    Morin, F.; Badeau, J.P.; Lambs, R.

    1996-01-01

    The purpose of this presentation is to give information on the changes in the design and manufacture of Primary Piping for electronuclear boilers of the Pressurized Water Reactor type (PWR) which has resulted in the making of one-piece forged lines including stub pipes and arcs. The optimization of these items is aimed at improving the life of the new power stations as well as guaranteeing their safety, while reducing inspection and maintenance requirements in service. The demonstration of the manufacturing feasibility has just been completed. It has taken material form in the installation, on the CIVAUX 1 section, of the first one-piece cold leg in the world. It will shortly be followed by the installation on the CIVAUX 2 section of a complete loop of bent forged pipes. Therefore, this new know-how is going to be incorporated in the French Rules (RCC-M) and can be directly taken into consideration both in the next work to be done and in the design and definition of a future nuclear reactor

  13. Die koste van vrywillige, beheerbare arbeidomset

    Directory of Open Access Journals (Sweden)

    G. Roodt

    1997-06-01

    Full Text Available The cost of voluntary, controllable labour turnover. Labour turnover for individuals can be classified as voluntary or non-voluntary, whereas labour turnover in organisations can be categorised as controllable or non-controllable. Data on total labour turnover in a particular service organisation indicated the existence of a possible problem. Voluntary, controllable labour turnover between 1 January 1988 and 31 March 1991 for technicians only within this particular organisation was closely scrutinised by calculating the direct recruitment, training, and separation costs for this period. The replacement costs of the technical population alone (N = 1594 for the last-mentioned period were approximately R94 million and could possibly increase to as high as R470 million if the hidden costs are also considered. If these costs are projected to the period 1980-1991 in which there were 60284 voluntary leavers, the total labour turnover costs for this organisation could be astronomical. It is clear from the above that preventative strategies by management could reduce the negative consequences of labour turnover and improve the prospects of a positive outcome. Opsomming Arbeidomset kan vir individue as vrywillig of nie-vrywillig geklassifiseer word; daarenteen kan arbeidomset vir organisasies as beheerbaar of nie-beheerbaar gekategoriseer word. Gegewens oor totale arbeidomset in "n bepaalde diensorganisasie het op die bestaan van 'n moontlike probleem gewys. Die koste van vrywillige, beheerbare arbeidomset van slegs tegnici is vir die periode 1 Januarie 1988 tot 31 Maart 1991 in die betrokke organisasie nader ondersoek, deur die direkte verkrygings-, opieidings- en skeidingskoste van tegniciverlaters vir hierdie tydperk te bereken. Die vervangingskoste van slegs die tegnicipopulasie (N = 1594 vir die laasgenoemde tydperk het sowat R94 miljoen beloop en kon selfs so hoog soos R470 miljoen wees as die verskuilde kostes ook verreken is. Indien hierdie kostes

  14. The effect of strain distribution on microstructural developments during forging in a newly developed nickel base superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Buckingham, R.C. [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom); Argyrakis, C.; Hardy, M.C. [Rolls-Royce plc, PO Box 31, Derby DE24 8BJ (United Kingdom); Birosca, S., E-mail: 522042@swansea.ac.uk [Institute of Structural Materials, Swansea University, Bay Campus, Fabian Way, Swansea SA1 8EN (United Kingdom)

    2016-01-27

    In the current study, the effect of strain distribution in a simple forging geometry on the propensity for recrystallization, and its impact on mechanical properties has been investigated in a newly developed experimental nickel-based superalloy. The new alloy was produced via a Powder Metallurgy (PM) route and was subsequently Hot Isostatic Processed (HIP), isothermally forged, and heat treated to produce a coarse grain microstructure with average grain size of 23–32 μm. The alloy was examined by means of Electron Back-Scatter Diffraction (EBSD) to characterise the microstructural features such as grain orientation and morphology, grain boundary characteristics and the identification of potential Prior Particle Boundaries (PPBs) throughout each stage of the processing route. Results at the central region of the cross-section plane parallel to the loading direction showed significant microstructural differences across the forging depth. This microstructural variation was found to be highly dependent on the value of local strain imparted during forging such that areas of low effective strain showed partial recrystallisation and a necklace grain structure was observed following heat treatment. Meanwhile, a fully recrystallised microstructure with no PPBs was observed in the areas of high strain values, in the central region of the forging.

  15. The Relevance Of The Preform Design In Coining Processes Of Cupronickel Alloy

    International Nuclear Information System (INIS)

    Buffa, G.; Fratini, L.; Micari, F.

    2007-01-01

    Coining is a forging process in which a metallic disk, characterized by a low volume-surface ratio, is deformed with the aim to impress 3D images on its three surfaces. Due to the large production volumes and, at the same time, to the high quality standards required to the final products in terms of final dimensions, tolerances and surface finishing, such closed-die, cold forging process requires a careful evaluation and choice of the proper operative parameters. In particular, along with technological parameters as the die velocity, die stroke and lubrication, which, in turn, contribute to affect the pressure values on the die surfaces, and thus the press choice, geometrical parameters as the side ring inner diameter and, above all, the preform geometry, strongly affect the quality of the obtained parts. In this paper, a 3D FEM model for coining processes is proposed, that is Lagrangian implicit, rigid-viscoplastic. The relationships between the obtained geometry and the starting preform shape is numerically investigated, allowing, through the analysis of the effective stresses, strain, and strain rate on the coin, as well as of the loads on the dies, to highlight the significance of the perform design in order to obtain a final product that satisfies the strict geometrical tolerances required. It is found that the best results on the final part are obtained with chamfered preform geometries, though larger values of force on the dies are observed

  16. Die verband tussen die sielkundige kontrak en organisasieverbondenheid

    Directory of Open Access Journals (Sweden)

    K. J. Stanz

    1999-06-01

    Full Text Available The relationship between the psychological contract and organisational commitment. The aim of this study is to design a measuring instrument with acceptable metric characteristics for the strength of the psychological contract within the South African context, and to determine empirically the relation between the strength of the psychological contract and organisational commitment. The Dhammanungune Model served as foundation for the design of the Strength of the Psychological Contract Questionnaire which consists of two scales namely, a needs expectation scale and a needs fulfilment expectation scale. The items of each scale have been formulated in the manner that ensures that the respondent reacts consecutively to two instructions namely, (a the level of the expectation and (b the importance of the expectation. This questionnaire was administered together with the Organisational Commitment Questionnaire to two population groups within the military environment. The Pearson Product Moment Correlation was calculated between the strength of the psychological contract and organisational commitment and the significance of the correlations was evaluated. Opsomming Die doel van die studie is om 'n meetinstrument met aanvaarbare metriese eienskappe vir die sterkte van die sielkundige kontrak vir Suid-Afrikaanse omstandighede te ontwerp en om empirics die verband tussen die sterkte van die sielkundige kontrak en organisasieverbondenheid te bepaal. Die sterkte van die sielkundige kontrak vraelys is op grond van die Dhammanungune-model ontwerp en het uit twee skale naamlik, die behoefteverwagting- en vervullingsverwagtingskale bestaan. Items vir eike skaal is sodanig geformuleer dat die respondent agteropeenvolgens op twee instruksies naamlik (a die vlak van die verwagting en (b die belangrikheid van die verwagting moet reageer. Die vraelys is saam met die organisasieverbondenheidsvraelys op twee populasies uit 'n militere omgewing toegepas. Die Pearson

  17. DIE ROL VAN DIE TAALWETENSKAP IN DIE ONTWIKKELING VAN ...

    African Journals Online (AJOL)

    aanslag op die sogenaamde "Intentional Fallacy", heelwat verder. n. Mens sou hier eintlik ook op die invloed van Lacan se toepassing van. De Sacs sure op Freud moet wys, en op Macherey se Theory of Literary. Production. Barthes is naamlik besig om repressie teen te werk, en die teks as produksieproses in stede van ...

  18. 77 FR 39997 - Heavy Forged Hand Tools, Finished or Unfinished, With or Without Handles From the People's...

    Science.gov (United States)

    2012-07-06

    ... DEPARTMENT OF COMMERCE International Trade Administration [A-570-803] Heavy Forged Hand Tools...) (Diamond Sawblades), the Department is notifying the public that the final judgment in this case is not in... review on heavy forged hand tools, finished or unfinished, with or without handles from the People's...

  19. Standard specification for titanium and titanium alloy forgings

    International Nuclear Information System (INIS)

    Anon.

    1975-01-01

    Standards are given for the purchase, manufacture, product testing and certification, packaging, and marketing of annealed Ti and Ti-alloy forgings. The specifications apply to the following Ti alloys: 6Al-Ti-4V, 5Al-Ti-2.5 Sn, and Ti + Pd. Acceptable values for the chemical requirements, product analysis limits, and tensile requirements are tabulated

  20. New trends in cold-chamber die casting machine design

    Directory of Open Access Journals (Sweden)

    R. Dańko

    2015-07-01

    Full Text Available Larger and larger proportions of aluminium castings, especially those produced by the die casting process, can be observed during recent years in the automotive industry, house-hold articles and others. In case of the automotive industry, apart from the traditional elements produced by the die pressure method such as engine blocks or crank shaft bedplates, aluminium is displacing steel from structural parts of cars (‘body in white’. The current state and development directions of the structural solutions of cold-chamber die castings are analysed in this paper. These solutions drive the prospective development of these machines and die casting technology. The focus is mainly on essential functional systems such as: hydraulic drives of closing and locking units, as well as pressing in die machines of known companies present on the European market.

  1. Aluminum extrusion with a deformable die

    NARCIS (Netherlands)

    Assaad, W.

    2010-01-01

    Aluminum extrusion process is one of metal forming processes. In aluminum extrusion, a work-piece (billet) is pressed through a die with an opening that closely resembles a desired shape of a profile. By this process, long profiles with an enormous variety of cross-sections can be produced to

  2. Die belangrikste kenmerk van die diereproduksie- bedrywe oor die ...

    African Journals Online (AJOL)

    digdhede teen 1980 uit 'n kudde van 30 rnilj.skape ge- produseer moet word. Tweedens sal die faktore ... die Republiek van Suid-Mrika teen 1980 in totaal 28 milj. sal wees. Indien die produsente dit as 'n ..... Appendix Table 4 in Digestive Physiology and nutrition of ruminants Vol. 3 Ed. and Publ. D.C. Church, Oregon State ...

  3. What history reveals about Forge River pollution on Long Island, New York's south shore.

    Science.gov (United States)

    Swanson, R Lawrence; Brownawell, B; Wilson, Robert E; O'Connell, Christine

    2010-06-01

    Fifty years ago, the Forge River and Moriches Bay, of Long Island's south shore lagoonal system, achieved notoriety when their polluted conditions were alluded to in a report of the US President's Science Advisory Committee (1965). The Woods Hole Oceanographic Institution investigated the bay throughout the 1950s, identifying duck farming as the cause of "objectionable", "highly contaminated" conditions of these waters. Much has changed: duck farming declined; the river was dredged to remove polluted sediments, improve navigation; and barrier island inlets stabilized. Yet, the river remains seasonally eutrophic. Why? This paper reviews what occurred in the Forge River watershed. While governments aggressively curtailed the impacts of duck pollution, they failed to manage development and sewage pollution. The Forge experience indicates that watershed management is a continuing governmental responsibility as development accelerates. Otherwise, we will always be looking for that instantaneous remediation that is usually not affordable and is socially contentious.

  4. Maintaining Low Voiding Solder Die Attach for Power Die While Minimizing Die Tilt

    Energy Technology Data Exchange (ETDEWEB)

    Hamm, Randy; Peterson, Kenneth A.

    2015-10-01

    This paper addresses work to minimize voiding and die tilt in solder attachment of a large power die, measuring 9.0 mm X 6.5 mm X 0.1 mm (0.354” x 0.256” x 0.004”), to a heat spreader. As demands for larger high power die continue, minimizing voiding and die tilt is of interest for improved die functionality, yield, manufacturability, and reliability. High-power die generate considerable heat, which is important to dissipate effectively through control of voiding under high thermal load areas of the die while maintaining a consistent bondline (minimizing die tilt). Voiding was measured using acoustic imaging and die tilt was measured using two different optical measurement systems. 80Au-20Sn solder reflow was achieved using a batch vacuum solder system with optimized fixturing. Minimizing die tilt proved to be the more difficult of the two product requirements to meet. Process development variables included tooling, weight and solder preform thickness.

  5. Die brein soos beskou deur die Grieke en Romeine

    Directory of Open Access Journals (Sweden)

    Francois P. Retief

    2015-02-01

    Full Text Available In Ou Egipte is mummifikasie met uitgebreide reseksie of uitsnyding van organe geassosieer, maar geen kennis is geneem van die morfologie van die brein nie. Griekse skrywers van die sesde en vyfde eeue v.C. het die brein aanvanklik gesien as die setel van intelligensie, die orgaan van sensoriese waarneming en gedeeltelik die oorsprong van sperma. Pneuma het ’n belangrike rol in breinfunksie gespeel. Hippokrates was die eerste om die brein te beskryf as ’n dubbele orgaan, wat met harsingvlies (meninges bedek, funksioneel van pneuma afhanklik en vertolker van begrip is. Tydgenote soos Plato, Aristoteles en Diokles het tot die beskrywing bygedra, maar laasgenoemde twee het beweer dat die hart die middelpunt van intelligensie is en nie die brein nie. Gedurende die laaste helfte van die vierde eeu v.C. is disseksie van die menslike liggaam tydelik aan die mediese skool van Alexandrië toegelaat en het dit tot merkwaardige vooruitgang in die begrip van die menslike anatomie en fisiologie gelei. Herofilus en Erasistratus het uitstekende beskrywings van die struktuur en funksie van die brein gegee wat eers in die tweede eeu n.C. deur Galenus geëwenaar is.

  6. Die Britse owerheid en die onderwys op Heidelberg gedurende die ...

    African Journals Online (AJOL)

    The establishment of Christian National Education (CNE) Schools stimulated the concept of mother tongue education. Oor die klaskamerpraktyk en die werklike gehalte van onderrig tydens die kampskooltydperk is daar min bekend. Heidelberg wat na 1902 in 'n belangrike onderwyssentrum in Transvaal ontwikkel het, het ...

  7. Sedimentêre omgewings van die Inhaca-eilandstelsel met spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente

    Directory of Open Access Journals (Sweden)

    Marieke Peché

    2011-09-01

    Full Text Available Die Inhaca-eilandstelsel is geleë langs die suidooskus van Mosambiek. Die oostekant van die stelsel grens aan die Indiese Oseaan en die westekant aan die Baai van Maputo. Hierdie eilandstelsel bestaan uit Inhaca- en Portugese eiland, asook ’n groep sandbanke wat van die noordlike punt van Inhaca na Portugese eiland strek. Die doel van hierdie studie is om die verskillende moderne en oer-sedimentêre omgewings op die eilandstelsel te identifiseer en te beskryf, die invloed van getye en golfaksie op die moderne sedimentêre omgewing vas te stel en die geochemiese en petrografiese samestelling van die geologiese eenhede te bepaal.

  8. Die Ware Buch und die Philologie

    Directory of Open Access Journals (Sweden)

    Bernhard Hurch

    2017-10-01

    Full Text Available Die im 19. Jahrhundert sich verändernden Produktionsbedingungen für Druckwerke (Buchdruck, Satz, Papier, Bindung wirkten katalysierend auf die Fachkonstitution und Institutionalisierung der Philologien. Hier steht der tatsächliche Buchmarkt im Vordergrund der Darstellung, das Käuferpublikum und die Voraussetzungen des Vertriebs. Dazu gehören auch die Rezension als entstehende Textsorte und die rasch arbeitenden Rezensionsorgane. F.-R. Hausmann wurde in den letzten Jahren unentbehrlicher Mitarbeiter dieses im Rahmen des Grazer Schuchardt-Projekts "Netzwerk des Wissens" angesiedelten Ansatzes.

  9. Manufacturing of ultra-large diameter 20 MnMoNi 5 5 steel forgings for reactor pressure vessels and their properties

    International Nuclear Information System (INIS)

    Onodera, S.; Kawaguchi, S.; Tsukada, H.; Moritani, H.; Suzuki, K.; Sato, I.

    1985-01-01

    As the structural material for RPV typical of increased dimensions, as set of ultra-large diameter steel forgings for a PHWR RPV is presented as outlined below. (1) Material designation: 20 MnMoNi 5 5 (similar to SA508, Cl.3) (2) Size of the forgings: flanges, 8.440 mm OD, a weight of 238 tons for shell flange; shells and torus, 7,920 mm OD, with large height, cover dome, 6,800 mm OD in chord and 460 mm thick; blank before formed to dome is ca. 8,000 mm OD. (3) Chemical composition: particular effort was made for minimizing the tramp elements as P, S, As, Sn, Sb, Cu. (4) Manufacturing, key points: steel making - combined refining and degassing in ladle; ingot making - largest size ingots, including 570 ton and 500 ton ingots; forging - special ''outside-the-press'' forging and forming techniques; heat treatment - prevention of H 2 flaking in normalizing and tempering and handling of the extra-large forgings at water quenching. (5) Metallurgical properties: sufficiently uniform carbon distributions in the forgings; a lowest possible content of hydrogen, non-metallic inclusions and oxygen. Mechanical properties: uniformity in tensile and toughness properties; flaws - only limited number of spots of UT indications under 2 mm EFG (EFS). (orig.)

  10. Die tug oor ampsdraers tydens die doleansie van 1886

    Directory of Open Access Journals (Sweden)

    J. Visser

    1986-06-01

    Full Text Available In art 29 van die Nederlandse Geloofsbelydenis word bely: “Die merktekens om die ware Kerk te ken is die volgende: As die Kerk die suiwere prediking van die evangelie uitoefen, as dit die suiwer bediening van die sakramente gebruik soos Christus dit ingestel het, as die kerklike tug gebruik word om die sondes te straf.” Dit spreek vanself dat wanneer ampsdraers, aan wie Christus sy kudde toevertrou het (Hand 20 : 28, met leer en /of lewenswandel in sonde volhard en nie daarin met tug gestuit word nie, word die ware kerk nie gebou nie maar afgebreek. 0ns sal later in hierdie artikel aantoon hoedanig die suiwer tug oor ampsdraers, veral leertug, tydens die Doleansie tot skade van die kerk van Christus agterweë gebly het.

  11. Weldability and mechanical property characterization of weld clad alloy 800H tubesheet forging

    International Nuclear Information System (INIS)

    King, J.F.; McCoy, H.E.

    1984-09-01

    The weldability of an alloy 800H forging that simulates a steam generator tubesheet is studied. Weldability was of concern because a wide range of microstructures was present in this forging. The top and portions of the bottom were weld clad with ERNiC-3 weld metal to a thickness of 19 mm similar to that anticipated for HTGR steam generators. Examinations of the clad fusion line in various regions revealed no weldability problems except possibly on the bottom portion, which contained large grains and some as-cast structure. A few microfissures were evident in this region, but no excessive hot cracking tendency was observed. The tensile properties in all areas of the clad forging were reasonable and not influenced greatly by the microstructure. The elevated-temperature tests showed strong tendency for fracture in the heat-affected zone of the alloy 800H. Creep failure at 649 0 C consistently occurred in the heat-affected zone of the alloy 800H, but the creep strength exceeded the expected values for alloy 800H

  12. Material Behavior Based Hybrid Process for Sheet Draw-Forging Thin Walled Magnesium Alloys

    International Nuclear Information System (INIS)

    Sheng, Z.Q.; Shivpuri, R.

    2005-01-01

    Magnesium alloys are conventionally formed at the elevated temperatures. The thermally improved formability is sensitive to the temperature and strain rate. Due to limitations in forming speeds, tooling strength and narrow processing windows, complex thin walled parts cannot be made by traditional warm drawing or hot forging processes. A hybrid process, which is based on the deformation mechanism of magnesium alloys at the elevated temperature, is proposed that combines warm drawing and hot forging modes to produce an aggressive geometry at acceptable forming speed. The process parameters, such as temperatures, forming speeds etc. are determined by the FEM modeling and simulation. Sensitivity analysis under the constraint of forming limits of Mg alloy sheet material and strength of tooling material is carried out. The proposed approach is demonstrated on a conical geometry with thin walls and with bottom features. Results show that designed geometry can be formed in about 8 seconds, this cannot be formed by conventional forging while around 1000s is required for warm drawing. This process is being further investigated through controlled experiments

  13. Die kritiek van tradisie en die tradisie van kritiek in die Geesteswetenskappe. 'n Rekonstruksie van die debat tussen Habermas en Gadamer

    OpenAIRE

    Duvenage, Pieter

    2013-01-01

    In hierdie bydrae word die bekende debat (1967-1971) tussen Jürgen Habermas en Hans-Georg Gadamer gerekonstrueer. Die debat word hier in noue samehang met die kwessie van die geesteswetenskappe gelees. Die bydrae val in vier dele uiteen. In die eerste afdeling word Habermas se opening tot die debat in vyf onderafdelings uiteengesit. Dit gaan hier oor Gadamer se verdediging van tradisie en Habermas se kritiek op die begrip (1.1). In antwoord op Gadamer se begrip van tradisie ontwerp Habermas s...

  14. Die transvaalse ontwerp-ordonnansie oor die onderwys

    Directory of Open Access Journals (Sweden)

    J. C. Coetzee

    1952-03-01

    Full Text Available In ’n Buitengewone Provinsiale Koerant van die Provinsie Transvaal is onder datum 25 Junie 1952 gepubliseer ’n „Ontwerp-Ordonnansie tot samevatting en wysiging van die Wette betreffende die Sentrale Beheer van die Onderwys, die Plaaslike Beheer van Skole, Godsdiensonderrig in Openbare Skole, Taal en die Onderwys, Onderwyspersoneel, Verpligte Onderwys, Toelating van Leerlinge tot Skole, Klasse of Inrigtings, Openbare Onderwys, Private Skole, Onderwys vir Kleurlinge en Asiate en Onderwys vir Naturelle, en om vir sake in verband daarmee voorsiening te maak” .

  15. The effects of thermomechanical history on the microstructure of a nickel-base superalloy during forging

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, S., E-mail: 485354@swansea.ac.uk [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom); Li, W. [Rolls-Royce plc, PO Box 31, Derby DE24 8BJ (United Kingdom); Coleman, M. [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom); Johnston, R., E-mail: r.johnston@swansea.ac.uk [College of Engineering, Bay Campus, Swansea University, Swansea SA1 8EN (United Kingdom)

    2016-06-21

    The effect of thermo-mechanical history on hot compression behaviour and resulting microstructures of a nickel base superalloy is presented. Hot compression tests were carried out on HAYNES® 282® specimens to varying strains from 0.1 to 0.8. Both single pass and multi-pass tests were completed. 60 min inter-pass times were utilized to accurately replicate industrial forging practices. The effect of dynamic, metadynamic and static recrystallization during inter-pass times on flow stress was investigated. The resulting microstructures were analysed using scanning electron, optical microscopy and EBSD to relate grain size and homogeneity with flow stress data. The study showed a negligible difference between multi-pass and single pass tests for strain increments above 0.2. Therefore, when modelling similar low strain and strain rate forging processes in HAYNES® 282®, previous forging steps can be ignored.

  16. 31 CFR 370.40 - Can I be held accountable if my negligence contributes to a forged signature?

    Science.gov (United States)

    2010-07-01

    ... 31 Money and Finance: Treasury 2 2010-07-01 2010-07-01 false Can I be held accountable if my negligence contributes to a forged signature? 370.40 Section 370.40 Money and Finance: Treasury Regulations... if my negligence contributes to a forged signature? (a) General. If your failure to exercise ordinary...

  17. DIE PLEK VAN SANG EN MUSIEK IN DIE PROTESTANTSE ...

    African Journals Online (AJOL)

    Test

    Sy moet hierdie opdrag uitvoer deur mid del van die Prediking d.w.s. deur middel van die Woord-vorm, maar ook deur die bediening van die sakramente, dws. deur middel van die vorm van die Daad. Maar nou wil God nie hê dat die Kerk slegs één maal die Evangelie sal predik en die mense sal doop om hulle daarna.

  18. A new Friction and Lubrication Test for Cold Forging

    DEFF Research Database (Denmark)

    Bay, Niels; Wibom, Ole; Aalborg Nielsen, J

    1995-01-01

    This paper presents a new friction and lubrication test for cold forging. The test allows controlled variation of the surface expansion in the range 0-2000%, the tool temperature in the range 20-270°C and the sliding length between 0 and infinite. Friction is decreasing with increasing temperature...

  19. Thomas Erastus oor die struktuur van die gemeenskap'^

    African Journals Online (AJOL)

    óók aansprake en regte het, is die opvatting dat sowel die burgerlike gemeenskap as die kerk 'n perfecta societas sibi sufficiens is, nié werklik aanvaar nie. Die Middeleeuse gemeenskap was die corpus christianum,. 'n gemeenskap wat nie deur fisiese of politieke grense beperk was nie. Sy grense het gelê waar die grense ...

  20. Die vestiging van die Kerk in Natal, die Vrystaat en Transvaal na ...

    African Journals Online (AJOL)

    as eerste predikant van die Voortrekkers laat orden en bevestig. Daama het verskeie kerksake van tyd tot tyd aandag geniet. Met betrekking tot die bevestiging van huwelike stel Retief 'n meer ordelike reëling daar, naamlik dat die gebooie van voomemende egpa- re van nou af drie maal in die kerk afgekondig moes wrord ...

  1. Die historiese betroubaarheid van die aartsvadervertellinge. 'n Beknopte bespreking van die huidige debat na aanleiding van die jongste publikasie

    Directory of Open Access Journals (Sweden)

    W. Vosloo

    1982-08-01

    Full Text Available Die afgelope twintig jaar was daar �n toenemende belangstelling in die aartsvadervertellinge in Genesis. Benewens die talle tydskrifartikels het skrywers soos die volgende ook boeke oor die onderwerp die lig laat sien: A. Parrot (1962, W. M. Clark (1964, R. Kilian (1966, R. E. Clements (1967, N. Lohfink (1967, H. Weidemann (1968, R. Martin-Achard (1969, T. L. Thompson (1974, J. van Seters (1975, J. P. Fokkelman (1975, C. Westermann (1976, R. Rendtorff (1977, J. Bright (1977, W. McKane (1979 en A. R. Millard en D. J. Wiseman (1980.

  2. Prediking aan die hand van die metafoor van fiksieskryf

    African Journals Online (AJOL)

    p1243322

    HTS 64(3) 2008 siening van die self en waarheid. In die pre-moderne paradigma kan die dominante metafoor verstaan word aan die hand van 'n spieël wat die lig uit 'n transendente oorsprong weerkaats, terwyl die moderne paradigma uitgedruk word met die metafoor van 'n lamp wat 'n eie, oorspronklike lig binne die self.

  3. Application of directional solidification ingot (LSD) in forging of PWR reactor vessel heads

    International Nuclear Information System (INIS)

    Benhamou, C.; Poitrault, I.

    1985-09-01

    Creusot-Loire Industrie uses this type of ingot for manufacture of Framatome 1300 and 1450 MW 4-loop PWR reactor vessel heads. This type of ingot offers a number advantages: improved internal soundness; greater chemical, structural and mechanical homogeneity of the finished part; simplified forging process. After a brief description of the pouring and solidification processes, this paper presents an analysis of the results of examinations performed on the prototype forging, as well as review of results obtained during industrial fabrication of dished heads from LSD ingots. The advantages of the LSD ingot over conventional ingots are discussed in conclusion

  4. Ontsporing van die regstaatsbegrip en sy konsekwensies vir die afrikanervolk

    Directory of Open Access Journals (Sweden)

    N. G.S. Van der Walt

    1966-03-01

    Full Text Available Die opvatting van die suiwere regstaat bring sy vraagstukke mee wanneer dit in verband gebring word met die leer van die soewereiniteit in eie kring. Laasgenoemde leer wortel in die geloof dat God die mens roep tot diens aan Hom, en dat die mens vry moet wees om ten opsigte van alle lewensaspekte God na die hoogste mate te kan dien. Hierdie verskeidenheid van aspekte is deur dr. A. Kuyper en sy volgelinge gesistemati- seer tot menslike verbande en lewenskringe, elk met ’n be- paalde sfeer waarin ander kringe nie mag inmeng nie. Elkeen is dan soewerein binne sy eie kring. Met verwysing na die staat is dan gespreek van die staatstaak as synde die hand- hawing van die reg, en omdat die staat in toenemende mate hom veral in die latere tyd ook besig gehou het met bedrywig- hede wat nouliks as van juridiese aard beskou kan word, is daar die onderskeid gemaak tussen die primêre en sekundêre taak van die staat. Die sistematiek van die wetsidee, deur prof. Dooyeweerd ontwikkel, waar die staat sy bestemmingsfunksie in die regsaspek vind, het vanselfsprekend geen plek vir so 'n dualistiese staatstaak nie, en die oplossing is deur sommige daarin gesoek om sulke staatsoptrede te vertolk as hebbende wel betrekking op die regsgemeenskap of die regsverkeer. Staatsondernemings soos paaie, spoorweë, spellingreëling, ens. word dan beskou as noodsaaklik vir die instandhouding van die regsgemeenskap en regsverkeer. Tereg wys A. M. Donner1 daarop dat so ’n vertolking eintlik neerkom op ’n oorspanning van die regsbegrip. Hy self sien dan die staatstaak in vrede- of orde-handhawing, wat in die eerste plaas wel regshandha- wing veronderstel. Onder orde word dan alles verstaan wat noodsaaklik is vir die gladde verkeer in die ontwikkelingsgang van die regsgemeenskap. Die wese van die staat het dan vol- gens hom te doen met reg, maar sy taak is meer as suiwere regshandhawing. Wat onrus verwek en die orde versteur, moet uit die openbare lewe verwyder word, en die

  5. Effect of nonmetallic inclusions on anisotropy of ductility in 35KhN3MFA steel forgings

    International Nuclear Information System (INIS)

    Shtremel', M.A.; Yavojskij, V.I.; Volkov, V.A.; Chursin, G.M.; Chukhlov, V.I.; Fetisov, G.I.; Mochalin, N.K.; Smol'yaninov, L.V.

    1980-01-01

    Characteristics of nonmetaltic inclusions and anizotropy of ductility and of impuct strength of forgings of the 35KhN3MFA steel are compared at different variants of melting and outer-furnace treatment. It is shown that method of melting rugulates anisotropy of ductility primarily through deformability of large inclusions during forging. Deformability of inclusions considerably changes due to introduction of silicocalcium in iron mold [ru

  6. Development of production technology and investigation of quality for forged-welded turbine rotors of steel 25Kh2NVFA

    International Nuclear Information System (INIS)

    Borisov, I.A.; Merinov, G.N.; Slezkina, E.V.

    1997-01-01

    A study was made into mechanical properties and microstructure of turbine rotor components manufactured by forging and heat treated under various conditions. It is revealed that the optimal heat treatment of forgings must include double quenching with subsequent tempering at 630-640 deg C for 10-20 h. Forged and welded rotors should be tempered at 620-630 deg C for 50-100 h. Microscopic examination and mechanical tests showed that low alloy steel 25Kh2NMF can be successfully used for manufacturing rotors of high-, medium-and low-heat turbines

  7. Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

    Science.gov (United States)

    Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

    2015-10-01

    Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

  8. Development of SiC Nanoparticles and Second Phases Synergistically Reinforced Mg-Based Composites Processed by Multi-Pass Forging with Varying Temperatures

    Directory of Open Access Journals (Sweden)

    Kaibo Nie

    2018-01-01

    Full Text Available In this study, SiC nanoparticles were added into matrix alloy through a combination of semisolid stirring and ultrasonic vibration while dynamic precipitation of second phases was obtained through multi-pass forging with varying temperatures. During single-pass forging of the present composite, as the deformation temperature increased, the extent of recrystallization increased, and grains were refined due to the inhibition effect of the increasing amount of dispersed SiC nanoparticles. A small amount of twins within the SiC nanoparticle dense zone could be found while the precipitated phases of Mg17Al12 in long strips and deformation bands with high density dislocations were formed in the particle sparse zone after single-pass forging at 350 °C. This indicated that the particle sparse zone was mainly deformed by dislocation slip while the nanoparticle dense zone may have been deformed by twinning. The yield strength and ultimate tensile strength of the composites were gradually enhanced through increasing the single-pass forging temperature from 300 °C to 400 °C, which demonstrated that initial high forging temperature contributed to the improvement of the mechanical properties. During multi-pass forging with varying temperatures, the grain size of the composite was gradually decreased while the grain size distribution tended to be uniform with reducing the deformation temperature and extending the forging passes. In addition, the amount of precipitated second phases was significantly increased compared with that after multi-pass forging under a constant temperature. The improvement in the yield strength of the developed composite was related to grain refinement strengthening and Orowan strengthening resulting from synergistical effect of the externally applied SiC nanoparticles and internally precipitated second phases.

  9. Modelling the void deformation and closure by hot forging of ingot castings

    DEFF Research Database (Denmark)

    Christiansen, Peter; Hattel, Jesper Henri; Kotas, Petr

    2012-01-01

    by mechanical deformation. The aim of this paper is to analyze numerically if and to what degree the voids areclosed by the forging. Using the commercial simulation software ABAQUS, both simplified model ingots and physically manufactured ingots containing prescribed void distributions are deformed and analyzed....... The analysis concernsboth the void density change and the location of the voids in the part after deformation. The latter can be important for the subsequent reliability of the parts, for instance regarding fatigue properties. The analysis incorporates the Gurson yield criterion for metals containing voids...... and focuses on how the voids deform depending on their size and distribution in the ingot as well ashow the forging forces are applied....

  10. DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE HUIDIGE ...

    African Journals Online (AJOL)

    Test

    DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE. HUIDIGE SITUASIE. Sending is 'n deel van die vervulling van die apostoliese opdrag van die kerk. Dit geskied op grond van en in gehoorsaamheid aan Gods. \\C'oord. Teologiese besinning is daarom die eerste en grondliggende vereiste by die ontwerp van 'n ...

  11. Die sestienpersoonlikheidsfaktorvraelys as hulpmiddel by die takseersentrum

    Directory of Open Access Journals (Sweden)

    J. C. D. Augustyn

    1988-05-01

    Full Text Available The 16PF Personality Test as an aid to the assessment centre Assessment centres still remains costly and thime consuming. This study investigates the reduction of time and costs by the use of the 16 PF Personality Test as a method for measuring management dimensions. Promising results were obtained with a relatively small sample for the prediction of initiative and perseverance. Significant multiple correlations were also found for three criteria of management success. Further research may establish the use of the 16 PF as an aid to management assessment and thereby reduce the costs and time involved in assessment centres. Opsomming Takseersentrums se grootste probleem is gelee in die koste en tyd wat dit behels. Hierdie studie ondersoek die moontlikheid om beide te verminder deur die aanwending van die 16 PF Persoonlikheidsvraelys vir die meting van bestuursdimensies. Belowende resultate is met 'n relatiewe klein steekproef bevind ten opsigte van die voorspelling van inisiatiefen deursettingsvermoe. Beduidende meervoudige korrelasies is ook ten opsigte van drie kriteria van bestuursukses bevind. Verdere navorsing kan die gebruik van die 16 PF as hulpmiddel by bestuursevaluering vestig en sodoende die tydsduur en koste van takseersentrums verminder.

  12. Development of service-relevant materials data and economic quality assurance and machining procedures for gas turbine blades. Final report; Entwicklung betriebsrelevanter Werkstoffkennwerte und wirtschaftlicher Qualitaetssicherungs- und Bearbeitungsverfahren fuer GT-Schaufeln. Schlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Buergel, R.; Rechtenbacher, H.

    1994-01-01

    In the frame of the reported project, together with the programme partners, optimization of service relevant properties as well as modification of manufacturing procedures for the forged alloy Nimonic 101 were achieved. These results are directly implementable into serial production and cause improved service reliability and economic benefit. For the forged alloy Udimet 720 materials data were generated in accordance with the programme plan. The final evaluation for this alloy will be performed by the project partner Siemens-KWU. The qualification of fine-grained investment cast blades of IN 792 for large rear=stage blading is not yet fully completed. Three major questions are lacking final answers: - Does a stress rupture strength advantage exist over the forged alloy Udimet 720/coarse/grained? - Can a high cycle fatigue strength as high as that for Udimet 720/coarse-grained be met reproducibly? - Does the investment cast blades offer a cost advantage over the forged ones - technical qualification assumed? The programme helped significantly in preparing the right answers to these questions. (orig.) [Deutsch] Im Rahmen des berichteten Teilvorhabens ist es in Zusammenarbeit mit den Projektpartnern gelungen, fuer die Schmiedelegierung Nimonic 101 die betriebsrelevanten Eigenschaften zu optimieren, sowie die Schaufelherstellung so zu modifizieren, dass die Betriebszuverlaessigkeit verbessert wird. Diese Ergebnisse sind direkt in die Serienfertigung implementierbar und damit wirtschaftlich nutzbar. Fuer die Schmiedelegierung Udimet 720 wurden im Rahmen des Projektverbundes Werkstoffkennwerte ermittelt. Die Gesamtauswertung fuer diesen Werkstoff erfolgt von Projektpartner Siemens-KWU. Das Bild zur Qualifikation feinkoerniger Feingussschaufeln ist noch nicht restlos klar. Drei wesentliche, noch abschliessend zu beantwortende Fragen sind: - Ergibt sich ein Zeitstandfestigkeitsvorteil gegenueber der Schmiedelegierung Udimet 720/Grobkorn? - Laesst sich reproduzierbar eine

  13. die korrelasie tussen die gemiddelde daaglikse toename van ...

    African Journals Online (AJOL)

    'n Regressielyn is uit die gegewens bereken deur 'n beswaarde regressieanaliese en die 80 persent-voorspellings- bande is bepaal. Die punte wat ver buite die normale ver- spreidingsband geval hetkon almal met goeie rede as abnor- maal beskou word (sien tabel 1) en is nie ingesluit by die statistiese berekenings nie.

  14. Army Combat Medic Resilience: The Process of Forging Loyalty.

    Science.gov (United States)

    Abraham, Preetha A; Russell, Dale W; Huffman, Sarah; Deuster, Patricia; Gibbons, Susanne W

    2018-03-01

    This study presents a grounded theory analysis of in-depth interviews of United States Army Combat Medics (CMs) who had served in Iraq and/or Afghanistan. The study explores how 17 CMs nominated by their peers as resilient cope with military stressors in order to identify the factors that enable them to thrive amidst harsh conditions. Four distinct categories of characteristics unique to this group emerged: (1) social bonding, (2) readiness, (3) dual loyalty as performance, and (4) leader by example. Forging loyalty underpins these characteristics and represents the main process used by resilient CMs and comprised three behavior patterns: (1) commitment to the family, (2) commitment to the military mission, and (3) commitment to their guiding religious and spiritual beliefs. Prominent behavioral tendencies of forging loyalty likely developed during childhood and re-enforced by families, friends, and other role models. Based on the findings, new training and education efforts should focus on developing positive emotional, environmental, and social resources to enhance the health and well-being of service members and their families.

  15. enkele fasette van die problematiek van die akademikus by die skryf

    African Journals Online (AJOL)

    Om verskeie redes het dit van die allergrootste belong geword dot 'n his- tories korrekte, wetenskaplike weerga- we van bogenoemde gebeure opge- teken moet word. Die sluier, in sommige gevalle am logiese redes toegepas, moes eenvoudig gelig word am gebeure wat die gewone man op stroot in Suid-Afrika dikwels ...

  16. Memory as social glue: Close interpersonal relationships in amnesic patients

    Directory of Open Access Journals (Sweden)

    Patrick S.R. Davidson

    2012-12-01

    Full Text Available Memory may be crucial for establishing and/or maintaining social bonds. Using the National Social life, Health, and Aging Project questionnaire, we examined close interpersonal relationships in three amnesic people: K.C. and D.A. (who are adult-onset cases and H.C. (who has developmental amnesia. All three patients were less involved than demographically-matched controls with neighbors and religious and community groups. A higher-than-normal percentage of the adult-onset (K.C. and D.A. cases’ close relationships were with family members, and they had made few new close friends in the decades since the onset of their amnesia. On the other hand, the patient with developmental amnesia (H.C. had forged a couple of close relationships, including one with her fiancé. Social networks appear to be winnowed, but not obliterated, by amnesia. The obvious explanation for the patients’ reduced social functioning stems from their memory impairment, but we discuss other potentially important factors for future study.

  17. Effects of boron additions and solutionizing treatments on microstructures and ductility of forged Ti–6Al–4V alloys

    International Nuclear Information System (INIS)

    Luan, J.H.; Jiao, Z.B.; Chen, G.; Liu, C.T.

    2015-01-01

    Highlights: • Proper boron additions and heat-treatments improve the ductility of Ti64 alloys. • Coarse TiB precipitates embrittle the Ti64 alloys causing ductility loss. • Modified Ti64 forged alloys with high strength and high ductility are developed. - Abstract: The effects of boron additions on the microstructure and mechanical properties of forged Ti–6Al–4V alloys in different heat-treatment conditions have been characterized by both experimental studies and thermodynamic calculations. The results indicate a combination of proper post-forging treatments and B additions are helpful for control of the prior-β grain size and the volume fraction of α phase, thereby tuning the ductility of the forged Ti–6Al–4V alloys. However, the B-containing alloys exhibit a significant drop in ductility if the solutionizing temperature is too high, and this embrittlement is mainly due to the coarsening of brittle TiB borides. The mechanism in this case is due to the cleavage fracture of TiB rather than its debonding with the matrix, as indicated by the observation of the aligned TiB borides on the matching areas of both halves of the fracture surfaces. Thus, the TiB size and orientation, the prior-β grain size, and the volume fraction of the α phase all play important roles in controlling the mechanical properties of the forged Ti–6Al–4V alloys. The current findings shed light on the composition–microstructure–ductility relationship in the forged Ti–6Al–4V alloys

  18. Effects of boron additions and solutionizing treatments on microstructures and ductility of forged Ti–6Al–4V alloys

    Energy Technology Data Exchange (ETDEWEB)

    Luan, J.H.; Jiao, Z.B. [Center for Advanced Structural Materials, Department of Mechanical and Biomedical Engineering, College of Science and Engineering, City University of Hong Kong, Hong Kong (China); Chen, G. [Engineering Research Center of Materials Behavior and Design, Ministry of Education, Nanjing University of Science and Technology, Nanjing 210094 (China); Liu, C.T., E-mail: chainliu@cityu.edu.hk [Center for Advanced Structural Materials, Department of Mechanical and Biomedical Engineering, College of Science and Engineering, City University of Hong Kong, Hong Kong (China)

    2015-03-05

    Highlights: • Proper boron additions and heat-treatments improve the ductility of Ti64 alloys. • Coarse TiB precipitates embrittle the Ti64 alloys causing ductility loss. • Modified Ti64 forged alloys with high strength and high ductility are developed. - Abstract: The effects of boron additions on the microstructure and mechanical properties of forged Ti–6Al–4V alloys in different heat-treatment conditions have been characterized by both experimental studies and thermodynamic calculations. The results indicate a combination of proper post-forging treatments and B additions are helpful for control of the prior-β grain size and the volume fraction of α phase, thereby tuning the ductility of the forged Ti–6Al–4V alloys. However, the B-containing alloys exhibit a significant drop in ductility if the solutionizing temperature is too high, and this embrittlement is mainly due to the coarsening of brittle TiB borides. The mechanism in this case is due to the cleavage fracture of TiB rather than its debonding with the matrix, as indicated by the observation of the aligned TiB borides on the matching areas of both halves of the fracture surfaces. Thus, the TiB size and orientation, the prior-β grain size, and the volume fraction of the α phase all play important roles in controlling the mechanical properties of the forged Ti–6Al–4V alloys. The current findings shed light on the composition–microstructure–ductility relationship in the forged Ti–6Al–4V alloys.

  19. Die huwelik as identiteitsmerker in die Ou Testament

    African Journals Online (AJOL)

    p1243322

    Gen 2:18). Uit die woorde van Genesis 2:24 dat man en vrou een sal wees, lei die derde formulier af dat dit “getuig dat die huwelik 'n allesinsluitende gemeenskap is ..... die formule gebruik word: “Hier volg die vertelling oor X se nageslag.” (Gen ..... verwys daarna as “intertwining the principal value concepts of tradition”.

  20. amp' van die ouderling in die Nuwe Testament

    African Journals Online (AJOL)

    Jesus self het geen kerk gestig nie en daarom, veral omdat die Jesus-beweging inter mums ten opsigte van die Joodse godsdiens van sy tyd tot stand gekom het, het ...... Die klem val dus nie op die npoTCTT0fievo<; se rang of outoriteit nie, maar op sy pastorale funksie in die huishouding of huisgemeente (kyk Reicke.

  1. The development of reactor vessel internal heavy forging for 1000 MW pressurized-water reactor nuclear power plant

    International Nuclear Information System (INIS)

    Zhang Zhifeng; Chen Yongbo; Ding Xiuping; Zhang Lingfang

    2012-01-01

    This Paper introduced the development of Reactor Vessel Internal (RVI) heavy forgings for 1000 MW Pressurized Water Reactor (PWR) nuclear power plant, analyzed the manufacture difficulties and technical countermeasures. The testing result of the product indicated that the performance of RVI heavy forgings manufactured by Shanghai Heavy Machinery Plant Ld. (SHMP) is outstanding and entirely satisfy the technical requirements for RVI product. (authors)

  2. Enkele opmerkings oor die intrinsieke waarde van die Latynse teks van Kodeks Bezae as herstelbron vir die Griekse teks van die Nuwe Testament

    Directory of Open Access Journals (Sweden)

    G. J.C. Jordaan

    1985-05-01

    Full Text Available Een van die belangrikste oud-Latynse vertalings word gevind in Kodeks Bezae, ’n vyfde-eeuse manuskrip van die vier Evangelies. Kodeks Bezae bevat ’n Griekse teks (D en ’n Latynse teks (d van die Evangelies langs mekaar, die Latynse teks in ’n lettertipe wat baie aan die Griekse majuskelskrif herinner. Wat hierdie dokument so merkwaardig maak, is die feit dat dit die enigste manuskrip is wat ’n Griekse Evangelie-teks uit die Westerse teksfamilie bevat.

  3. Kontekstuele bepalers by die beplanning van skoolwoordeboeke

    Directory of Open Access Journals (Sweden)

    Herman L. Beyer

    2011-10-01

    Full Text Available

    OPSOMMING: Die doel van hierdie artikel is om tot die metaleksikografiese gesprek oor skoolwoordeboeke as 'n tipe pedagogiese woordeboek by te dra. Die fokus is op kontekstuele bepalers wat by die beplanning van skoolwoordeboeke verreken behoort te word: Binne die konteks van 'n veeltalige Namibië word enkele onderwyskundige sisteme verken wat 'n impak op die ontwerp van gedrukte skoolwoordeboeke vir die sekondêre skoolfase kan hê, naamlik skoolkurrikula, die nasionale taalbeleid vir skole en die beleid van leerdergerigte onderwys. Hierdie artikel voer ook aan dat die voor die hand liggende teikengebruiker van 'n skoolwoordeboek, naamlik die leerder, nie die enigste teikengebruiker is nie: Die onderwyser word as medeteikengebruiker gestel wanneer dit by die gebruik van woordeboeke in die onderrigleersituasie kom. Verskillende tipes gevalle van woordeboekgebruik in die mikrokonteks van die onderrigleersituasie word onderskei, naamlik woordeboekonderrig, woordeboekgeïntegreerde taalonderrig en woordeboekgeondersteunde taalonderrig. Hierdie tipes gebruik behoort komponente van 'n woordeboekpedagogie te wees, wat uiteindelik behoort te lei tot outonome woordeboekgebruik en die gepaardgaande vestiging van 'n individuele woordeboekkultuur by die leerder. Die leksikograaf moet al hierdie aspekte inreken wanneer 'n skoolwoordeboek beplan word ten einde die nodige leksikografiese vernuwing in te voer. Enkele voorstelle vir sodanige vernuwings en vir verdere navorsing word ten slotte aangebied.

    Sleutelwoorde: GEBRUIKERSGERIGTE LEKSIKOGRAFIE, KONTEKS, LEERDER, LEERDERGERIGTE ONDERWYS, LEERWOORDEBOEK, LEKSIKOGRAAF, METALEKSIKOGRAFIE, NASLAANWOORDEBOEK, ONDERWYSER, PEDAGOGIESE WOORDEBOEK, SISTEEM, SKOOLWOORDEBOEK, TAALBELEID, TEIKENGEBRUIKER, WOORDEBOEKGEBRUIK, WOORDEBOEKGEÏNTEGREERDE TAALONDERRIG, WOORDEBOEKONDERSTEUNDE TAALONDERRIG, WOORDEBOEKONDERRIG, WOORDEBOEKPEDAGOGIE

    ABSTRACT: Contextual Determiners in the Planning of School

  4. n Oorsig van die huidige stand van navorsing oor die

    African Journals Online (AJOL)

    Test

    7 Jun 2011 ... Die eerste maal wat dit as deel van die teks van 1 Johannes aangehaal word, is in die. 4de eeu in 'n Latynse teks, Liber Apologeticus (hf 4). Eers aan die einde van die 16de eeu is dit in 'n amptelike Katolieke uitgawe van die Vulgaat ingesluit. Die doel van die Johannesbriewe. Waarom is die Briewe ...

  5. Effect of technological parameters on formability of semi-solid rheological casting-forging 6061 alloy

    Directory of Open Access Journals (Sweden)

    Jianbo TAN

    2016-02-01

    Full Text Available The 6061 alloy cooling curve is determined by analysis software, and the 6061 semi-solid alloy is prepared by manual paddling process. The primary solid fraction is tested through prepared water quenched samples under different temperature. With H1F100 type servo press and cup type test mold, the forming of the 6061 semi-solid alloy rheological casting-forging is made. The influence of alloy temperature, forming pressure, upper mould temperature and holding time on the formability of 6061 alloy is researched. The results show that within the same set of mold completing casting and forging of the alloy is feasible. Along with the increase of the alloy temperature and the upper mould temperature, the formability of finished products becomes better. Under this experimentation, when the temperature of the semi-solid alloy is amongst 642 ℃ to 645 ℃ and the upper mould preheating temperature is amongst 200 ℃ to 300 ℃, casting defects such as cold insulation will form in the casting-forging sample of semi-solid 6061 alloy with the prolongation of holding time.

  6. Die dogmatiese binding van die prediking

    African Journals Online (AJOL)

    genoemde probleemstelling wat ons homileties na riglyne wil soek, sonder die pretensie dat finale oplossings gevind sal word. Om hierdie probleem te ontleed is dit nodig om eers kortliks 'n begripsbepaling van die begrippe dogma, binding en prediking te maak. Vanuit die begripsbepaling kan ons dan probeer vasstel wat ...

  7. DIE HEDENDAAGSE SIENING VAN DIE NORMERING VAN DUITS ...

    African Journals Online (AJOL)

    v a k t a a l k w a l i £ i k a s i e s ) neem d i e I n s t i t u t t a l l e take waar ter u i t b r e i d i n g van kennis van die Duitse taal in die buiteland. Sedert 1964 publiseer die. Institut die tydskrif Deutsch als Fremdsprache met die bylae Sprachpraxis, asook 'n handboek met die titel Deutsch - eln Lehrbuch Eur Auslander (Duits.

  8. Die topkwark

    Directory of Open Access Journals (Sweden)

    R. Tegen

    1998-07-01

    Full Text Available ’n Oorsig van die belangrikheid van die onlangs ontdekte topkwark by Fermilab in Chicago word gegee. Daar word aangetnon dat die topkwark belangrik is in fisika van die Oerknal, oftewel "Big Bang", en in die Standaard Model van Elementêredeeltjie-fisika. Toepaslike literatuur vir verdere studie kan van die lys van verwysings in hierdie kort, nietegniese artikel, nagegaan word.

  9. oor die inhoud en boodskap van die heidelbergse kategismus

    African Journals Online (AJOL)

    Smit. Oor die Inhoud en Boodskap van die Heidelbergse Kategismus. 52. Uiteraard sal dié tema saamhang met die bedoelinge agter die opstel van die Kategismus. Ook die vraag na moontlike bedoelinge of motiewe is egter 'n ingewikkelder vraag as wat miskien gedink mag word. Uiteraard was daar agter elke kategismus ...

  10. Die vangnet van die woord: forensies-linguistiese getuienis in 'n ...

    African Journals Online (AJOL)

    Een van die redes daarvoor is waarskynlik die gepaardgaande sleurwerk verbonde aan die verwerking van die betrokke taaldata — iets wat egter deur die onlangse meteoriese vooruitgang in tegnologiese tegnieke op die agtergrond geskuif is en nuwe moontlikhede na vore laat kom het. In die lig van die kompleksiteit van ...

  11. Multipass forging of Inconel 718 in the delta-Supersolvus domain: assessing and modeling microstructure evolution

    Directory of Open Access Journals (Sweden)

    Zouari Meriem

    2014-01-01

    Full Text Available This work is focused on the evolution of the microstructure of Inconel 718 during multi-pass forging processes. During the forming process, the material is subjected to several physical phenomena such as work-hardening, recovery, recrystallization and grain growth. In this work, transformation kinetics are modeled in the δ-Supersolvus domain (T>Tsolvus where the alloy is single-phase, all the alloying elements being dissolved into the FCC matrix. Torsion tests were used to simulate the forging process and recrystallization kinetics was modeled using a discontinuous dynamic recrystallization (DDRX two-site mean field model. The microstructure evolution under hot forging conditions is predicted in both dynamic and post-dynamic regimes based on the initial distribution of grain size and the evolution of dislocation density distribution during each step of the process. The model predicts recrystallization kinetics, recrystallized grain size distribution and stress–strain curve for different thermo-mechanical conditions and makes the connection between dynamic and post-dynamic regimes.

  12. Dying scenarios improve recall as much as survival scenarios.

    Science.gov (United States)

    Burns, Daniel J; Hart, Joshua; Kramer, Melanie E

    2014-01-01

    Merely contemplating one's death improves retention for entirely unrelated material learned subsequently. This "dying to remember" effect seems conceptually related to the survival processing effect, whereby processing items for their relevance to being stranded in the grasslands leads to recall superior to that of other deep processing control conditions. The present experiments directly compared survival processing scenarios with "death processing" scenarios. Results showed that when the survival and dying scenarios are closely matched on key dimensions, and possible congruency effects are controlled, the dying and survival scenarios produced equivalently high recall levels. We conclude that the available evidence (cf. Bell, Roer, & Buchner, 2013; Klein, 2012), while not definitive, is consistent with the possibility of overlapping mechanisms.

  13. Die Voortrekker-Monument

    Directory of Open Access Journals (Sweden)

    Gerard Moerdyk

    1938-03-01

    Full Text Available Die Eeufeesjaar is vir die Afrikaner ’n tydperk van besieling. Nog nooit sedert die ontstaan van ons volk het een enkele gebeurtenis soveel nasietrots gewek as die honderdjarige herdenking van die Groot Trek. Vir die eerste keer in ons geskiedenis voel ons ons nie meer Kapenaars, Vrystaters, Natalers, en Transvalers nie, maar Afrikaners, saamgesnoer deur die tradisies van ’n selfstandige kultuurvolk. Wanneer die klimaks van die Ossewatrek met die hocksteenlegging van die Voortrekker-Monument bereik word, sal die besieling nie uitsterf nie, die krag wat geskep is sal bly voortgroei tot ’n onweerstaanbare mag. Die Afrikaner sal homself vind, en as die Monument na sowat vyf jaar onthul word, sal die saad wat in hierdie jaar gesaai is, tot voile rypheid gekom het. Dan sal die Monument self tot die volk spreek; intussen egter, is dit wenslik, nee noodsaaklik selfs, om die Monument aan die Afrikaners te verklaar, om ‘n uiteensetting te gee van die noodsaaklikheid van so ’n Monument, sowel as om die motief te verduidelik wat as inspirasie gedien het vir die ontwerpdaar van.

  14. e .Kuraioriufn. DIE W ETENSKAPLIKE BETEKENIS VAN DIE W ERK

    African Journals Online (AJOL)

    Test

    ENGELBRECHT ver antwoordelik vir die Ou-Testamentiese vakke en Hebreeus. Die aan stelling van 'n derde professor het noodsaaklik geword, want dit sou. 85 .... De .Spreuken ran 5a/o?no omvat die nuwe vertaling en die ekse gese van die eerste 24 hoofstukke van die Spreukeboek. Die geskoold- heid in die Semitiese ...

  15. Effect of Minor Titanium Addition on Copper/Diamond Composites Prepared by Hot Forging

    Science.gov (United States)

    Yang, Fei; Sun, Wei; Singh, Ajit; Bolzoni, Leandro

    2018-03-01

    Copper/diamond composites have great potential to lead the next generation of advanced heat sink materials for use in high-power electronic devices and high-density integrated circuits because of their potential excellent properties of high thermal conductivity and close thermal expansion to the chip materials (e.g., Si, InP, GaAs). However, the poor wettability between copper and diamond presents a challenge for synthesizing copper/diamond composites with effective metallurgical bonding and satisfied thermal performance. In this article, copper/diamond composites were successfully prepared by hot forging of elemental copper and artificial diamond powders with small amounts (0 vol.%, 3 vol.% and 5 vol.%) of titanium additives. Microstructure observation and mechanical tests showed that adding minor titanium additions in the copper/diamond composite resulted in fewer cracks in the composites' microstructure and significantly improved the bonding between the copper and diamond. The strongest bonding strength was achieved for the copper/diamond composite with 3 vol.% titanium addition, and the possible reasons were discussed.

  16. A multi-scale approach for high cycle anisotropic fatigue resistance: Application to forged components

    International Nuclear Information System (INIS)

    Milesi, M.; Chastel, Y.; Hachem, E.; Bernacki, M.; Loge, R.E.; Bouchard, P.O.

    2010-01-01

    Forged components exhibit good mechanical strength, particularly in terms of high cycle fatigue properties. This is due to the specific microstructure resulting from large plastic deformation as in a forging process. The goal of this study is to account for critical phenomena such as the anisotropy of the fatigue resistance in order to perform high cycle fatigue simulations on industrial forged components. Standard high cycle fatigue criteria usually give good results for isotropic behaviors but are not suitable for components with anisotropic features. The aim is to represent explicitly this anisotropy at a lower scale compared to the process scale and determined local coefficients needed to simulate a real case. We developed a multi-scale approach by considering the statistical morphology and mechanical characteristics of the microstructure to represent explicitly each element. From stochastic experimental data, realistic microstructures were reconstructed in order to perform high cycle fatigue simulations on it with different orientations. The meshing was improved by a local refinement of each interface and simulations were performed on each representative elementary volume. The local mechanical anisotropy is taken into account through the distribution of particles. Fatigue parameters identified at the microscale can then be used at the macroscale on the forged component. The linkage of these data and the process scale is the fiber vector and the deformation state, used to calculate global mechanical anisotropy. Numerical results reveal an expected behavior compared to experimental tendencies. We proved numerically the dependence of the anisotropy direction and the deformation state on the endurance limit evolution.

  17. Environmentally Benign Lubricant Systems For Cold, Warm And Hot Forging

    DEFF Research Database (Denmark)

    Bay, Niels

    2010-01-01

    paper gives an overview of these efforts substituting environmentally hazardous lubricants in cold, warm and hot forging. The paper is an extract of the keynote paper [3] written by the author together with eight co-authors referring to collected papers and other information from more than 30 different...

  18. Die faktore gemeenskaplik aan die selfondersoekvraelys van Holland en die nuwe Suid-Afrikaanse beroepsbelangstellingsvraelys

    Directory of Open Access Journals (Sweden)

    C. Swanevelder

    1992-06-01

    Full Text Available The factors common to the Self Directed Search of Holland (SDS and the new South African Vocational Interest Inventory (SAVII. The new South African Vocational Interest Inventory was locally developed with the purpose to create a single vocational interest inventory for all population groups in the RSA. In this study the common factors underlying the SDS and the SAVII were determined with the aid of interbattery factor analysis. The results indicate that there are six common factors underlying the two instruments for both the standard nine boys and girls, and that these factors agree with the six factors built into the SDS by Holland. Opsomming Die nuwe Suid-Afrikaanse Beroepsbelangstellingsvraelys (SABBV is plaaslik ontwikkel met die doel om 'n enkele beroepsbelangstellingsvraelys vir alle bevolkingsgroepe binne die RSA, daar te stel. In hierdie studie is daar ondersoek ingestel na die gemeenskaplike faktore onderliggend aan die SABBV en die Selfondersoekvraelys (SOV van Holland met behulp van 'n interbatteryfaktorontleding. Daar is bevind dat daar ses gemeenskaplike faktore onderliggend aan die twee instrumente is vir sowel standerd nege seuns as dogters, en dat hierdie faktore ooreenstem met die ses faktore wat deur Holland in die SOV ingebou is.

  19. P. J. N. Smal, Die Universalisme in die Psalms. Academisch ...

    African Journals Online (AJOL)

    Test

    dat die historiese element in Israel se Godsopenbaring en daarmee die insig in sy betekenis te kort gedoen word. Die betekenis van die studie vir die historia revelationis is daardeur gering; as duidelike „tydlose” sistematisering van Outestamentiese gegewens oor die betrokke onder- werpe, soos die laaste hoofstuk, bl.

  20. Die Defects and Die Corrections in Metal Extrusion

    Directory of Open Access Journals (Sweden)

    Sayyad Zahid Qamar

    2018-05-01

    Full Text Available Extrusion is a very popular and multi-faceted manufacturing process. A large number of products for the automotive, aerospace, and construction sectors are produced through aluminum extrusion. Many defects in the extruded products occur because of the conditions of the dies and tooling. The problems in dies can be due to material issues, design and manufacturing, or severe usage. They can be avoided by maintaining the billet quality, by controlling the extrusion process parameters, and through routine maintenance. Die problems that occur on a day-to-day basis are mostly repairable and are rectified through various types of die correction operations. These defects and repair operations have not been reported in detail in the published literature. The current paper presents an in-depth description of repairable die defects and related die correction operations in metal extrusion. All major die defects are defined and classified, and their causes, preventive measures, and die correction operations are described. A brief frequency-based statistical study of die defects is also carried out to identify the most frequent die corrections. This work can be of direct benefit to plant engineers and operators and to researchers and academics in the field of metal extrusion.

  1. Development of a forging technology for the production of high-pressure compressor blades from γ-titanium aluminide. Project C: production of primary wrought material for the forging of turbine blades from gamma-TiAl and their microstructural optimization. Final report

    International Nuclear Information System (INIS)

    Appel, F.; Oehring, M.; Lorenz, U.; Wagner, R.

    1999-01-01

    By the development of a new canning technique which resulted in an effective thermal isolation of can and billet the flow stress mismatch of can and billet material could be minimized, which allowed crack-free and uniform extrusion. Using this technique which has been applied for patent hot extrusion is an effective and matured working method for ingot material. It allows to produce fine-grained and almost fully recrystallized material with increased workability as has been found by the determination of the forging window as well as by the successful forging of more than 200 compressor blades by the project partner Thyssen Umformtechnik. By forging under suited conditions also a microstructural homogenization is achieved in comparison to extruded material. (orig.)

  2. A friction model for cold forging of aluminum, steel and stainless steel provided with conversion coating and solid film lubricant

    DEFF Research Database (Denmark)

    Bay, Niels; Eriksen, Morten; Tan, Xincai

    2011-01-01

    Adopting a simulative tribology test system for cold forging the friction stress for aluminum, steel and stainless steel provided with typical lubricants for cold forging has been determined for varying normal pressure, surface expansion, sliding length and tool/work piece interface temperature...

  3. Developments of New Lubricants for Cold Forging of Stainless Steel

    DEFF Research Database (Denmark)

    Steenberg, Thomas; Christensen, Erik; Olesen, P.

    1997-01-01

    Two new lubricant systems for cold forging of stainless steel have been developed. The main component of these systems are FeCl3 and ZnCa2(PO4)2, respectively. Both lubricant systems have been tested using a backward extrusion test. The results show excellent lubricating properties with respect...

  4. Ageing of forged superaustenitic stainless steel: Precipitate phases and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Anburaj, J., E-mail: janburaj@gmail.com [Department of Metallurgical Engineering, PSG College of Technology, Coimbatore 641 004 (India); Nazirudeen, S.S. Mohamed; Narayanan, R.; Anandavel, B.; Chandrasekar, A. [Department of Metallurgical Engineering, PSG College of Technology, Coimbatore 641 004 (India)

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer Solutionizing of 1250 Degree-Sign C and ageing of 500-1000 Degree-Sign C was done for hot forged SASS. Black-Right-Pointing-Pointer Strength and toughness increased by 25% on hot forged than the cast SASS. Black-Right-Pointing-Pointer Amounts of precipitates after ageing were evaluated by thermo-calc. Black-Right-Pointing-Pointer Sigma forms from chi at 900 Degree-Sign C and contains constant Cr and Mo contents, unlike chi. Black-Right-Pointing-Pointer Sigma is incoherent, contains high Mo and causes low toughness at 900 Degree-Sign C. - Abstract: Cast superaustenitic stainless steel (SASS), of composition 19 wt% Cr, 20 wt% Ni, 7.5 wt% Mo and 0.37 wt% N, is hot forged at 1200 Degree-Sign C. The forging was then solutionized at 1250 Degree-Sign C and aged for 1 h and 10 h at different temperatures in the range of 500-1000 Degree-Sign C. Effect of these treatments on (i) hardness and (ii) fracture toughness based on impact energy is reported. Chi is formed from low temperatures up to 800 Degree-Sign C, and sigma at temperatures above 900 Degree-Sign C. A model is proposed to illustrate the dissolution of chi and sigma in austenite at elevated temperatures. Compared with chi, sigma contains more Mo. Toughness decreased with increasing amounts of chi and sigma precipitates. However, in the temperature range of 850-950 Degree-Sign C, low toughness was observed for relatively a short ageing time, although virtually the volume of sigma phase is very low. This is attributed to the presence of incoherent sigma in austenite matrix. Fractographs of the impact-tested samples indicated an increased tendency for brittle fracture with increasing ageing temperatures (increase in sigma content). Thermodynamic calculations substantiated (i) EDS results of composition of secondary phases present in the aged SASS and (ii) the proposed model. From these studies it is concluded that sigma is enriched in Mo at 900 Degree-Sign C and can be as

  5. Geslagsverskille in die ouditiewe ontlokte potensiaal van die brein

    Directory of Open Access Journals (Sweden)

    Anita D Stuart

    2006-10-01

    Full Text Available Gender differences in the auditory evoked potential of the brain. Based on literature indications of an association between temperament characteristics and the evoked potential of the brain, and indications of gender differences in certain temperament traits, the purpose of this study was to ascertain whether evoked responses also differentiated between the genders. A sample of 81 male and 210 female students was randomly selected. Two auditory evoked potential procedures were applied. The results indicated statistically significant differences in evoked potential responses between the genders. The results are interpreted against the background of sensory and neurological sources of the evoked potential responses and linked to the neurophysiological foundations of temperament. Opsomming: Gegrond op aanduidings in die literatuur van ’n assosiasie tussen temperamentskenmerke en die ontlokte potensiaal van die brein, sowel as aanduidings van geslagsverskille in sekere temperamentstrekke, was die doel van die huidige studie om te bepaal of ontloktepotensiaal-response ook tussen die geslagte onderskei. ’n Steekproef van 81 manlike en 210 vroulike studente is ewekansig geselekteer. Twee ouditiewe ontloktepotensiaal- prosedures is toegepas. Die resultate het op statisties beduidende verskille tussen die geslagte gedui. Die bevindinge word teen die agtergrond van die sensoriese en neurologiese oorsprong van ontloktepotensiaal–response geïnterpreteer en verbind aan die neurofisiologiese verankering van temperament.

  6. Tensile properties of a dual-axial forged Ti–Fe–Cu alloy containing boron

    Energy Technology Data Exchange (ETDEWEB)

    Zadorozhnyy, V.Yu., E-mail: zadorozhnyyvlad@gmail.com [National University of Science and Technology “MISIS”, Leninsky prospect, 4, Moscow 119049 (Russian Federation); Institute for Materials Research, Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577 (Japan); Shchetinin, I.V.; Chirikov, N.V. [National University of Science and Technology “MISIS”, Leninsky prospect, 4, Moscow 119049 (Russian Federation); Louzguine-Luzgin, D.V. [WPI Advanced Institute for Materials Research, Tohoku University, Katahira 2-1-1, Aoba-Ku, Sendai 980-8577 (Japan)

    2014-09-22

    In the present work we introduce a micro/nano-structured α+β Ti-based low-alloy produced by the tilt-casting method and subjected to subsequent thermo-mechanical treatment. After hot dual-axial forging at 900 °C, subsequent heating at 700 °C and water quenching a Ti{sub 94}Fe{sub 3}Cu{sub 3}+1000 ppm of boron alloy, containing inexpensive alloying elements, showed an ultimate tensile strength value of about 950 MPa and percentage elongation of about 5.2%. It is shown that the intensive forging treatment and subsequent heat treatment are leading to significantly improved mechanical properties of such an alloy compared to the as-cast state.

  7. die doeltreffendheid van die afrikaanse woordelys en spelreels

    African Journals Online (AJOL)

    sluiting by die reel vir die verdubbeling van medeklinkers na 'n kort, be- klemtoonde klinker, woorde soos ballet, ballon, terras, terrein, dissipel en dissipline slegs met een konsonant na die eerste vokaal gespel moes word, omdat daardie voorafgaande vokaal onbeklemtoon is. Ook hierdie uit- sondering op die reel word ...

  8. calvyn oor die leiding van die heilige gees in die verklaring van die

    African Journals Online (AJOL)

    Mittel alters, bis er zur Ruhe kommt bei den kanonischen Schriften der. Urzeit der christlichen Ära (Barth ... (ego tamen dimoveri non possum ab amore compendii, CO 10, 403). Deur die boodskap van die .... Idem ergo spiritus qui per os prophetarum loquutus est, in corda nostra penetret necesse est, ut persuadeat fideliter ...

  9. Die verband tussen lokus van beheer en die werks prestasie van swart bemarkers in die lewensversekeringsbedryf

    Directory of Open Access Journals (Sweden)

    E. L. Coetzer

    1997-06-01

    Full Text Available The relationship between locus of control and the work performance of black marketers in the life assurance industry. The aim of the study was to establish the relationship between locus of control and the work performance of black marketers in the life assurance industry. These constructs were selected by virtue of the lack of empirical research regarding the assumed relationship between them. The Locus of Control Scale of Schepers (1995 was used for measuring locus of control. Work performance was measured by the commission earned per month by the marketer, the number of policies generated by the marketer, as well as the percentage of lapsed policies. The relevant measurements were obtained in respect of a sample of 149 black marketing personnel. The results indicated a modest but statistically significant relationship between external locus of control and the work performance of black marketers. Opsomming Die doel van die studie was om die verband tussen lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf te bepaal. Hierdie konstrukte is gekies op grond van die gebrek aan empiriese navorsing rakende die veronderstelde verband tussen genoemde konstrukte. Die Lokus van Beheer-vraelys van Schepers (1995 is in die meting van lokus van beheer gebruik. Werksprestasie is aan die hand van kommissie per maand verdien, aantal polisse gegenereer deur 'n bemarker en die persentasie vervalde polisse, gemeet. Die tersaaklike metinge is verkry ten opsigte van 'n steekproef van 149 swart bemarkers. Die resultate toon 'n klein, dog statisties beduidende verband tussen eksterne lokus van beheer en die werksprestasie van swart bemarkers in die lewensversekeringsbedryf.

  10. Qualification of laser based additive production for manufacturing of forging Tools

    Directory of Open Access Journals (Sweden)

    Junker Daniel

    2015-01-01

    Full Text Available Mass customization leads to very short product life cycles, so the costs of a tool have to be amortized with a low number of workpieces. Especially for highly loaded tools, like those for forging, that leads to expensive products. Therefore more economical production processes for tool manufacturing have to be investigated. As laser additive manufacturing is already used for the production of moulds for injection moulding, this technology maybe could also improve the forging tool production. Within this paper laser metal deposition, which is industrially used for tool repair, will be investigated for the use in tool manufacturing. Therefore a mechanical characterization of parts built with different laser process parameters out of the hot work tool steel 1.2709 is made by upsetting tests and hardness measurements. So the influence of the additive manufacturing process on the hardness distribution is analysed.

  11. The coarsening effect of SA508-3 steel used as heavy forgings material

    Directory of Open Access Journals (Sweden)

    Dingqian Dong

    2015-01-01

    Full Text Available SA508Gr.3 steel is popularly used to produce core unit of nuclear power reactors due to its outstanding ability of anti-neutron irradiation and good fracture toughness. The forging process takes important role in manufacturing to refine the grain size and improve the material properties. But due to their huge size, heavy forgings cannot be cooled down quickly, and the refined grains usually have long time to grow in high temperature conditions. If the forging process is not adequately scheduled or implemented, very large grains up to millimetres in size may be found in this steel and cannot be eliminated in the subsequent heat treatment. To fix the condition which may causes the coarsening of the steel, hot upsetting experiments in the industrial production environment were performed under different working conditions and the corresponding grain sizes were measured and analysed. The observation showed that the grain will abnormally grow if the deformation is less than a critical value. The strain energy takes a critical role in the grain evolution. If dynamic recrystallization consumes the strain energy as much as possible, the normal grains will be obtained. While if not, the stored strain energy will promote abnormal growth of the grains.

  12. Determination of interfacial heat transfer coefficient for TC11 titanium alloy hot forging

    Science.gov (United States)

    Lu, Baoshan; Wang, Leigang; Geng, Zhe; Huang, Yao

    2017-10-01

    In this paper, based on self-developed experimental apparatus, the upsetting test of TC11 titanium alloy on the hot flat die was conducted and Beck's nonlinear inverse estimation method was adopted to calculate the interfacial heat transfer coefficient (IHTC) and the change rules of IHTC following billet deformation rate, average interfacial temperature and holding time were investigated respectively. Experimental results indicate that IHTC increases with the increase of deformation rate as a whole, and the billet deformation heat and interfacial friction heat during forming that remarkably contribute to IHTC and the contributions by heat conduction to IHTC is differ from that by friction; the glass lubricant coated on the billet surface that weakens the heat transfer situation in the early stage of forging, however, this blocking effect of lubricant on IHTC soon vanishes with increasing deformation rate and it enhances the interface heat transfer later; the average interfacial temperature impacts on IHTC in many aspects and a high average interfacial temperature IHTC corresponds to a high IHTC when the deformation rate is certain, but this changing trend is not monotonous; the IHTC decreases with the increase of holding time due to oxidation. After certain holding time, the IHTC is only related to temperature and pressure in the absence of deformation rate, and the influence of pressure on IHTC is larger than that of temperature on it.

  13. die doel en wese van opvoedende onderwys en die implikasies

    African Journals Online (AJOL)

    Oaar moet onderskei word tussen die doelstellings van opvoedende onderwys en die einddoel wat bereik word deur die nastrewing van hierdie doelstellings. Gunter praat van die naderliggende doelstellings (1981, b1.105). \\/at die enddoel van opvoedende onderwys bet ref, gaan die meeste opvoedkundi ges akkoord dat ...

  14. Is die ortodoksie se verstaan van die sondeval belemmerend vir die gesprek tussen teologie en natuurwetenskap?

    Directory of Open Access Journals (Sweden)

    Johan Buitendag

    2012-11-01

    Full Text Available In hierdie artikel is betoog dat die Gereformeerde Ortodoksie se begrip van die sondeval ’n  belemmering  was  vir  die  gesprek  tussen  teologie  en  natuurwetenskap.  Die  rede hiervoor was dat dit ten eerste ’n bepaalde verstaan van liniêre tyd nahou en ten tweede dat dit ’n bonatuurlike ingryp veronderstel het. Albei hierdie aspekte het die debat onnodig problematiseer. Die argument is ontwikkel deur eerstens die probleem te definieer, gevolg deur ’n uiteensetting van die standpunte van Augustinus en Calvyn onderskeidelik oor die sondeval. As ’n heuristiese sleutel is die konsepte van infralapsarisme en supralapsarisme aangewend om die tema te ontleed. Die artikel is afgesluit met die oortuiging dat die imago Dei ’n beliggaamde menslike persoon is wat biologies in die geskiedenis in terme van selfbewussyn en morele verantwoordelikheid ontluik het. Is the Orthodoxy’s notion of the Fall inhibitory for the dialogue between theology and science? In this article it was argued that the Reformed Orthodoxy’s interpretation of the Fall had become an impediment in the dialogue between theology and science. The reason was that it assumed firstly a specific understanding of linear time and secondly a metaphysical intervention. Both events were unnecessarily problematising the debate. The argument was deployed by stating the problem, followed by an exposition of the views of Augustine and Calvin on the Fall. As a heuristic key, the concepts of infralapsarism and supralapsarism were applied respectively to analyse the topic. The article concluded with the conviction that the imago Dei is an embodied human person that had biologically emerged in history as a center of self-awareness, and moral responsibility.

  15. Die opleiding van bedryfsielkundiges aan die universiteit van Fort Hare

    Directory of Open Access Journals (Sweden)

    W. Botha

    1977-11-01

    Full Text Available Die Departement Bedryfsielkunde aan die Universiteit van Fort Hare is 'n relatiewe jong departement en het eers in 1965 tot stand gekom. Voor hierdie datum is Bedryfsielkunde as 'n kort kursus deur die departement van suiwer Sielkunde aangebied en een van die destydse dosente, Dr. W. Backer, het die inisiatief geneem om 'n selfstandige departement van Bedryfsielkunde in die Fakulteit van Ekonomiese Wetenskappe op die been te bring.

  16. Repetitive forging (RF) using inclined punches as a new bulk severe plastic deformation method

    Energy Technology Data Exchange (ETDEWEB)

    Babaei, A. [Department of Mechanical Engineering, University College of Engineering, University of Tehran, Tehran 11155-4563 (Iran, Islamic Republic of); Faraji, G., E-mail: ghfaraji@ut.ac.ir [Department of Mechanical Engineering, University College of Engineering, University of Tehran, Tehran 11155-4563 (Iran, Islamic Republic of); Department of Engineering Design and Manufacture, University of Malaya, 50603 Kuala Lumpur (Malaysia); Mashhadi, M.M. [Department of Mechanical Engineering, University College of Engineering, University of Tehran, Tehran 11155-4563 (Iran, Islamic Republic of); Hamdi, M. [Department of Engineering Design and Manufacture, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2012-12-15

    A new bulk severe plastic deformation method based on repetitive forging (RF) using inclined punches is proposed. This process consists of two half cycles. In the first half cycle, a square cross section deforms to parallelogram by forging with two inclined punches, and the parallelogram cross section is forged back to square using two flat punches in the second half cycle. This method was applied to commercially pure copper and significant grain refinement was achieved after four passes of RF. The results showed that significant improvement in the mechanical properties was obtained. Notable increase of yield and ultimate strengths corresponding to 358 MPa and 381 MPa after four passes of RF from the initial values of 121 MPa and 230.5 MPa is detectable. Microhardness increases to about 100 Hv after four passes of RF from the initial value of 53 Hv. Finite element (FE) results illustrate that RF is able to impose extremely high plastic strains to the materials. In the RF process, the processed samples have the same dimensions and geometry as those of the initial sample without any waste material and there is no need for back pressure.

  17. Anisotropy effects during dwell-fatigue caused by δ-phase orientation in forged Inconel 718

    Energy Technology Data Exchange (ETDEWEB)

    Saarimäki, Jonas, E-mail: jonas.saarimaki@liu.se [Division of Engineering Materials, Department of Management and Engineering, Linköping University, SE-58183 Linköping (Sweden); Colliander, Magnus Hörnqvist [Department of Applied Physics, Chalmers University of Technology, SE-41296 Göteborg (Sweden); GKN Aerospace Engine Systems, R& T Centre, SE-46181 Trollhättan (Sweden); Moverare, Johan J. [Division of Engineering Materials, Department of Management and Engineering, Linköping University, SE-58183 Linköping (Sweden)

    2017-04-24

    Inconel 718 is a commonly used superalloy for turbine discs in the gas turbine industry. Turbine discs are often subjected to dwell-fatigue as a result of long constant load cycles. The effect of anisotropy on dwell-fatigue cracking in forged turbine discs have not yet been thoroughly investigated. Crack propagation behaviour was characterised using compact tension (CT) samples cut in different orientations from a real turbine disc forging. Samples were also cut in two different thicknesses in order to investigate the influence of plane strain and plane stress condition on the crack propagation rates. The samples were subjected to dwell-fatigue tests at 550 °C with 90 s or 2160 s dwell-times at maximum load. Microstructure characterisation was done using scanning electron microscopy (SEM) techniques such as electron channelling contrast imaging (ECCI), electron backscatter diffraction (EBSD), and light optical microscopy (LOM). The forged alloy exhibits strong anisotropic behaviour caused by the non-random δ-phase orientation. When δ-phases were oriented perpendicular compared to parallel to the loading direction, the crack growth rates were approximately ten times faster. Crack growth occurred preferably in the interface between the γ-matrix and the δ-phase.

  18. 76 FR 8773 - Forged Stainless Steel Flanges From India and Taiwan

    Science.gov (United States)

    2011-02-15

    ... INTERNATIONAL TRADE COMMISSION [Investigation Nos. 731-TA-639 and 640 (Third Review)] Forged Stainless Steel Flanges From India and Taiwan AGENCY: United States International Trade Commission. ACTION... Taiwan would be likely to lead to continuation or recurrence of material injury. On January 31, 2011, the...

  19. Filosofiese tendense in die wordinggeskiedenis van ons verstaan van die fisiese natuur

    Directory of Open Access Journals (Sweden)

    D. F. M. Strauss

    2006-09-01

    Full Text Available Die ontstaan van ’n lang tradisie van natuurwetenskaplike denke is in antieke Griekeland te vind – die bakermat van die Westerse beskawing en die bron van geartikuleerde rasionele besinning. Die vroegste fases van die Griekse kultuur het reeds geboorte geskenk aan ’n teoretiese nadenke oor die heelal. Die Pythagoreërs is veral bekend vir hul klem op die verklaringskrag van getalsverhoudinge. In hul tese dat “alles getal is” het hulle egter slegs rasionale getalle (breuke erken en gevolglik uiteindelik vasgeloop in die ontdekking van irrasionale getalle wat tot die geometrisering van die Griekse wiskunde gelei het en tegelyk die bedding gevorm het van waaruit ’n magtige tradisie van ruimte-metafisika gegroei het wat die hele middeleeuse tydperk omspan het. Die vermeende statiese syn is in die mees ekstreme geval – die skool van Parmenides en die argumente van Zeno teen veelheid en beweging – tot in die uiteindelike antinomiese konsekwensies daarvan deurdink. Dit was egter eers die vroeg-moderne tyd – die voorgangers en nakomelinge van Galilei – wat naas getal en ruimte ’n waardering ontwikkel het vir die verklaringskrag van beweging (vergelyk die klassieke meganistiese wêreldbeeld van die heelal as ’n meganisme van stofdeeltjies in beweging. Maar ook hierdie meganistiese reduksie (waardeur alle fisiese verskynsels herlei is tot die beweging van al of niegelade massapunte sou uiteindelik misluk omdat dit nie van die onomkeerbaarheid van fisiese prosesse rekenskap kon gee nie. Gevolglik beliggaam eers die fisika van die 20ste eeu ’n erkenning van die deurslaggewend-stempelende rol van energie-werking (dus van die fisiese aspek in die aard van stoflike dinge en prosesse. Die artikel word afgesluit met ’n vlugtige verduideliking van die implikasies van die voorafgaande argumentasie vir ’n benadering van die misterie van die bestaan van materie.

  20. A Probabilistic Analysis of the Nxt Forging Algorithm

    Directory of Open Access Journals (Sweden)

    Serguei Popov

    2016-12-01

    Full Text Available We discuss the forging algorithm of Nxt from a probabilistic point of view, and obtain explicit formulas and estimates for several important quantities, such as the probability that an account generates a block, the length of the longest sequence of consecutive blocks generated by one account, and the probability that one concurrent blockchain wins over an- other one. Also, we discuss some attack vectors related to splitting an account into many smaller ones.

  1. Forging of cast Mg-3Sn-2Ca-0.4Al-0.4Si magnesium alloy using processing map

    International Nuclear Information System (INIS)

    Rao, K. P.; Suresh, K.; Prasad, Y. V. R. K.; Hort, N.; Kainer, K. U.

    2016-01-01

    Mg-3Sn-2Ca (TX32) alloy has good creep resistance but limited workability. Minor amounts of Al and Si have been added to TX32 for improving its hot workability. The processing map for the TX32-0.4Al-0.4Si alloy exhibited two workability domains in the temperature and strain rate ranges: (1) 310-415.deg.C/0.0003-0.003 s-1 and (2) 430-500.deg.C/0.003-3 s-1. The alloy exhibited flow instability at temperatures < 350.deg.C at strain rates > 0.01 s-1. The alloy has been forged to produce a cup shape component to validate these findings of processing map. Finite-element (FE) simulation has been performed for obtaining the local variations of strain and strain rate within the forging. The microstructures of the forged components under the optimal domain conditions revealed dynamically recrystallized grains, and those forged in the flow instability regime have fractured and exhibited flow localization bands and cracks. The experimental load stroke curves correlated well with those obtained by FE simulation.

  2. Forging of cast Mg-3Sn-2Ca-0.4Al-0.4Si magnesium alloy using processing map

    Energy Technology Data Exchange (ETDEWEB)

    Rao, K. P.; Suresh, K.; Prasad, Y. V. R. K. [University of Hong Kong, Hong Kong (China); Hort, N.; Kainer, K. U. [Magnesium Innovation Centre, Geesthacht (Germany)

    2016-06-15

    Mg-3Sn-2Ca (TX32) alloy has good creep resistance but limited workability. Minor amounts of Al and Si have been added to TX32 for improving its hot workability. The processing map for the TX32-0.4Al-0.4Si alloy exhibited two workability domains in the temperature and strain rate ranges: (1) 310-415.deg.C/0.0003-0.003 s-1 and (2) 430-500.deg.C/0.003-3 s-1. The alloy exhibited flow instability at temperatures < 350.deg.C at strain rates > 0.01 s-1. The alloy has been forged to produce a cup shape component to validate these findings of processing map. Finite-element (FE) simulation has been performed for obtaining the local variations of strain and strain rate within the forging. The microstructures of the forged components under the optimal domain conditions revealed dynamically recrystallized grains, and those forged in the flow instability regime have fractured and exhibited flow localization bands and cracks. The experimental load stroke curves correlated well with those obtained by FE simulation.

  3. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    African Journals Online (AJOL)

    Test

    vergewe. Dit sou in orde gewees het as daar gestaan het, ReMomë- j^onta^is hepta?ds. wat die grieks is vir sewentig maal sewe. Die uitdrukking. heMom&ontabis heptd sien hoogswaarskynlik op Gen. 4 : 24 (LXX) waar. Lameg meedeel dat hy sewe-en-sewentig-maal gewreek sal word. Daar sit die Afr. Vert, die uitdrukking ...

  4. Application of laser additive manufacturing to produce dies for aluminium high pressure die casting

    CSIR Research Space (South Africa)

    Pereira, MFVT

    2012-07-01

    Full Text Available through immersion in liquid aluminium. The dipping cycle closely resembles the heating and cooling cycle of a typical aluminium die under casting conditions. The suitability of any LAM technology, that can produce fully dense metallic components... cost vs wrought manufactured 5.2 1,7 2. 2 Average cost Very High Medium High Table 3: Processing and finishing costs of test coupons 3.1 Cyclic Immersion in Molten Aluminium Figure 3 below shows the testing apparatus developed to simulate...

  5. Forging Consensus for Implementing Youth Socialization Policy in Northwest China

    Science.gov (United States)

    Fairbrother, Gregory P.

    2011-01-01

    The goal of this article is to examine how the provincial education media in China play a role of forging consensus among local actors responsible for the implementation of new centrally-promulgated youth socialization policy. In doing so, it also explores the tension among three of the Chinese state's claims to legitimacy: economic development,…

  6. Large forging manufacturing process

    Science.gov (United States)

    Thamboo, Samuel V.; Yang, Ling

    2002-01-01

    A process for forging large components of Alloy 718 material so that the components do not exhibit abnormal grain growth includes the steps of: a) providing a billet with an average grain size between ASTM 0 and ASTM 3; b) heating the billet to a temperature of between 1750.degree. F. and 1800.degree. F.; c) upsetting the billet to obtain a component part with a minimum strain of 0.125 in at least selected areas of the part; d) reheating the component part to a temperature between 1750.degree. F. and 1800.degree. F.; e) upsetting the component part to a final configuration such that said selected areas receive no strains between 0.01 and 0.125; f) solution treating the component part at a temperature of between 1725.degree. F. and 1750.degree. F.; and g) aging the component part over predetermined times at different temperatures. A modified process achieves abnormal grain growth in selected areas of a component where desirable.

  7. Modeling the Mechanical Performance of Die Casting Dies

    Energy Technology Data Exchange (ETDEWEB)

    R. Allen Miller

    2004-02-27

    The following report covers work performed at Ohio State on modeling the mechanical performance of dies. The focus of the project was development and particularly verification of finite element techniques used to model and predict displacements and stresses in die casting dies. The work entails a major case study performed with and industrial partner on a production die and laboratory experiments performed at Ohio State.

  8. Analytical and experimental evaluation of a proposed self-forging fragment munition

    International Nuclear Information System (INIS)

    Tuft, D.B.; Folsom, E.N.

    1982-01-01

    Analytical and experimental tools have been used to study the formation of a proposed self-forging fragment projectile. The primary objective of this study is the determination of the interior and exterior shape of the fully formed fragment, and to determine if the fragment tumbles in flight. In addition, it is of interest to compare computer predictions to experimental results. An experiment was performed using high speed photography and high-energy flash x-ray radiography to study liner and case motion and projectile formation. Fabrication and assembly tolerances were closely controlled in an effort to eliminate tolerances as a possible source of fragment instability. X-ray film-density contours were analyzed to determine the fully formed fragment interior and exterior shape. Down-range yaw screens showed fragment tumbling in flight. The computed fragment shape was compared to experimental results and it was found that a retaining ring in the computational model near the liner periphery had a significant effect on the final computed fragment shape. With the retaining ring in the computational model and full two-way sliding between all material interfaces, the final computed fragment showed very good agreement with the experiment on both exterior and interior shapes

  9. Fatigue properties of high-strength materials used in cold-forging tools

    DEFF Research Database (Denmark)

    Brøndsted, P.; Skov-Hansen, P.

    1998-01-01

    In the present work classical analytical models are used to describe the static stress–strain curves, low-cycle fatigue properties and fatigue crack growth behaviour of high-strength materials for use in tools for metal-forming processes such as cold forging and extrusion. The paper describes the...

  10. Developments of steel fabrication processes for castings and ingots for forgings

    International Nuclear Information System (INIS)

    Fernandez, S.

    1980-01-01

    This chapter deals with a series of technological developments in the manufacture of steels which have occurred during the last years, in particular reporting the results obtained in Reinosa with some of these methods in the fabrication of castings as well as forgings and rolled products. (author)

  11. 75 FR 67110 - Forged Stainless Steel Flanges From India and Taiwan

    Science.gov (United States)

    2010-11-01

    ... Stainless Steel Flanges From India and Taiwan AGENCY: United States International Trade Commission. ACTION... India and Taiwan. SUMMARY: The Commission hereby gives notice that it has instituted reviews pursuant to... the antidumping duty orders on forged stainless steel flanges from India and Taiwan would be likely to...

  12. X-ray tomography studies on porosity and particle size distribution in cast in-situ Al-Cu-TiB{sub 2} semi-solid forged composites

    Energy Technology Data Exchange (ETDEWEB)

    Mathew, James; Mandal, Animesh [School of Minerals, Metallurgical and Materials Engineering, Indian Institute of Technology, Bhubaneswar (India); Warnett, Jason; Williams, Mark A. [WMG, University of Warwick, Coventry CV4 7AL (United Kingdom); Chakraborty, Madhusudan [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur (India); Srirangam, Prakash, E-mail: p.srirangam@warwick.ac.uk [WMG, University of Warwick, Coventry CV4 7AL (United Kingdom)

    2016-08-15

    X-ray computed tomography (XCT) was used to characterise the internal microstructure and clustering behaviour of TiB{sub 2} particles in in-situ processed Al-Cu metal matrix composites prepared by casting method. Forging was used in semi-solid state to reduce the porosity and to uniformly disperse TiB{sub 2} particles in the composite. Quantification of porosity and clustering of TiB{sub 2} particles was evaluated for different forging reductions (30% and 50% reductions) and compared with an as-cast sample using XCT. Results show that the porosity content was decreased by about 40% due to semi-solid forging as compared to the as-cast condition. Further, XCT results show that the 30% forging reduction resulted in greater uniformity in distribution of TiB{sub 2} particles within the composite compared to as-cast and the 50% forge reduction in semi-solid state. These results show that the application of forging in semi-solid state enhances particle distribution and reduces porosity formation in cast in-situ Al-Cu-TiB{sub 2} metal matrix composites. - Highlights: •XCT was used to visualise 3D internal structure of Al-Cu-TiB{sub 2} MMCs. •Al-Cu-TiB{sub 2} MMC was prepared by casting using flux assisted synthesis method. •TiB{sub 2} particles and porosity size distribution were evaluated. •Results show that forging in semi-solid condition decreases the porosity content and improve the particle dispersion in MMCs.

  13. n hoofstuk in die (outo)biografie van die predikant (pastor?) 1 ...

    African Journals Online (AJOL)

    biografie van die dominee (pastor?), spreek om verskeie redes boekdele. Die gebruik van die onbepaalde lidwoord is eerstens 'n bevestiging dat die artikel slegs 'n verdere bydrae (hoofstuk) tot die bestaande en steeds voortgaande gesprek (boek) oor die biografie van die dominee is (Heitink 2001). Tweedens plaas ek ...

  14. Movement Synchrony Forges Social Bonds Across Group Divides

    Directory of Open Access Journals (Sweden)

    Bahar eTuncgenc

    2016-05-01

    Full Text Available Group dynamics play an important role in the social interactions of both children and adults. A large amount of research has shown that merely being allocated to arbitrarily defined groups can evoke disproportionately positive attitudes toward one’s in-group and negative attitudes toward out-groups, and that these biases emerge in early childhood. This prompts important empirical questions with far-reaching theoretical and applied significance. How robust are these inter-group biases? Can biases be mitigated by behaviors known to bond individuals and groups together? How can bonds be forged across existing group divides? To explore these questions, we examined the bonding effects of interpersonal synchrony on minimally constructed groups in a controlled experiment. In-group and out-group bonding were assessed using questionnaires administered before and after a task in which groups performed movements either synchronously or non-synchronously in a between-participants design. We also developed an implicit behavioral measure, the Island Game, in which physical proximity was used as an indirect measure of interpersonal closeness. Self-report and behavioral measures showed increased bonding between groups after synchronous movement. Bonding with the out-group was significantly higher in the condition in which movements were performed synchronously than when movements were performed non-synchronously between groups. The findings are discussed in terms of their importance for the developmental social psychology of group dynamics as well as their implications for applied intervention programs.

  15. Modelling the influence of carbon content on material behavior during forging

    Science.gov (United States)

    Korpała, G.; Ullmann, M.; Graf, M.; Wester, H.; Bouguecha, A.; Awiszus, B.; Behrens, B.-A.; Kawalla, R.

    2017-10-01

    Nowadays the design of single process steps and even of whole process chains is realized by the use of numerical simulation, in particular finite element (FE) based methods. A detailed numerical simulation of hot forging processes requires realistic models, which consider the relevant material-specific parameters to characterize the material behavior, the surface phenomena, the dies as well as models for the machine kinematic. This data exists partial for several materials, but general information on steel groups depending on alloying elements are not available. In order to generate the scientific input data regarding to material modelling, it is necessary to take into account the mathematical functions for deformation behavior as well as recrystallization kinetic, which depends alloying elements, initial microstructure and reheating mode. Besides the material flow characterization, a detailed description of surface changes caused by oxide scale is gaining in importance, as these phenomena affect the material flow and the component quality. Experiments to investigate the influence of only one chemical element on the oxide scale kinetic and the inner structure at high temperatures are still not available. Most data concerning these characteristics is provided for the steel grade C45, so this steel will be used as basis for the tests. In order to identify the effect of the carbon content on the material and oxidation behavior, the steel grades C15 and C60 will be investigated. This paper gives first approaches with regard to the influence of the carbon content on the oxide scale kinetic and the flow stresses combined with the initial microstructure.

  16. A coupled thermo-mechanical pseudo inverse approach for preform design in forging

    Science.gov (United States)

    Thomas, Anoop Ebey; Abbes, Boussad; Li, Yu Ming; Abbes, Fazilay; Guo, Ying-Qiao; Duval, Jean-Louis

    2017-10-01

    Hot forging is a process used to form difficult to form materials as well as to achieve complex geometries. This is possible due to the reduction of yield stress at high temperatures and a subsequent increase in formability. Numerical methods have been used to predict the material yield and the stress/strain states of the final product. Pseudo Inverse Approach (PIA) developed in the context of cold forming provides a quick estimate of the stress and strain fields in the final product for a given initial shape. In this paper, PIA is extended to include the thermal effects on the forging process. A Johnson-Cook thermo-viscoplastic material law is considered and a staggered scheme is employed for the coupling between the mechanical and thermal problems. The results are compared with available commercial codes to show the efficiency and the limitations of PIA.

  17. DIE ROL VAN DIE SUID-AFRIKAANSE WEERMAG IN NATUUR- EN ...

    African Journals Online (AJOL)

    sedert die vroeg 1900's deur die Weermag be- heer. In 1967 was dit die eerste militere terrein wat tot privaatnatuurreservaat verklaar is. Vhembe bestaan uit 4 hoofplantgemeenskappe nl. rivieraewerbos, vloedvlaktes, ranteveld en die sandveldplato. Wildsoorte op die terrein sl!Jit rooibokke, bosbokke, waterbokke, koedoes,.

  18. Die entwicklung, die metamorphose, die entstehung: Die konzepte des organismus von Aristoteles bis Darwin

    Directory of Open Access Journals (Sweden)

    Kamerer Eva

    2009-01-01

    Full Text Available (nemački In diesem Aufsatz versuche ich, die Elemente verschiedener Konzepte des Organismus in der Philosophie und in der Wissenschaft zu analysieren. Die Deutungen des Organismus und der Einheit der Natur bei Aristoteles, Kant und Goethe werden als ein Beispiel der Bewegung von einem finalistischen zum antifinalistischen Bild der Natur verstanden.

  19. die aard van wetgewende diskresies by die suid-afrikaanse ...

    African Journals Online (AJOL)

    Administrator

    In enige moderne demokrasie is daar een of ander vorm van skeiding van magte tussen die wetgewende, uitvoerende en regsprekende gesag. Hierdie skeiding van magte, die sogenaamde trias politica, kan sover teruggevoer word as 1215, met die ondertekening van die Magna Carta deur Koning John van Engeland.

  20. die krag van simbole en rites in die liturgie 1. probleemstelling

    African Journals Online (AJOL)

    uitroepe vervang met die drie keer Kyrie eleison, die drie maal Christe eleison en die drie keer Kyrie eleison-uitroepe (Albrecht 1989:43). Op die lang duur het die uitroep dus heeltemal losgeraak van die gebede en het dit 'n selfstandige liturgiese element geword (Van Rongen. 1990:35). Die Reformasie met sy nadruk op ...

  1. Fatigue behavior of rolled and forged tungsten at 25°, 280° and 480 °C

    International Nuclear Information System (INIS)

    Habainy, J.; Iyengar, S.; Lee, Y.; Dai, Y.

    2015-01-01

    Pure tungsten has been chosen as the target material at the European Spallation Source facility in Lund. Calculations show that the target temperature can reach 500 °C momentarily during the spallation process, leading to thermal fatigue. Target life estimations require fatigue data at different temperatures and this work focuses on generating such data for pure, unirradiated, rolled and forged tungsten in the range 25°–480 °C. For specimens oriented in the rolling direction, tensile tests at room temperature indicated Young's modulus values in the range 320–390 GPa, low levels of plasticity (<0.23%) and UTS values in the range 397 MPa (unpolished) and 705 MPa (Polished). UTS for forged specimens were around 500 MPa. Stress-controlled fatigue tests were conducted in the tensile regime, with a runout limit of 2 × 10"6 cycles. At 25 °C, unpolished specimens had fatigue limits of 150 MPa (rolling and transverse direction), and 175 MPa (forged). For polished specimens in the rolling direction, fatigue limits were higher at 237.5 MPa (25 °C) and 252.5 MPa (280 °C). The forged specimens showed slightly better fatigue properties and marginal cyclic hardening at 480 °C. - Highlights: • Stress & strain-controlled fatigue tests on pure tungsten at 25°, 280° & 480 °C. • Unirradiated, rolled and forged specimens in polished and unpolished condition. • Min. tensile strength (MPa): 397 (25 °C), 472 (280 °C) and 363 (480 °C). • Min. endurance limit (MPa): 137.5 (25 °C), 250 (280 °C) and 150 (480 °C). • Marginal cyclic hardening observed at 480 °C.

  2. Effect of the Process Parameters on the Formability, Microstructure, and Mechanical Properties of Thin Plates Fabricated by Rheology Forging Process with Electromagnetic Stirring Method

    Science.gov (United States)

    Jin, Chul Kyu; Jang, Chang Hyun; Kang, Chung Gil

    2014-01-01

    A thin plate (150 × 150 × 1.2 mm) with embedded corrugation is fabricated using the rheoforming method. Semisolid slurry is created using the electromagnetic stirring (EMS) system, and the thin plate is made with the forging die at the 200-ton hydraulic press. The cross sections and microstructures of the slurry with and without stirring are examined. To investigate the effect of the process parameters on the formability, microstructure, and mechanical properties of thin plate the slurry is subjected to 16 types of condition for the forging experiment. The 16 types included the following conditions: Whether the EMS is applied or not, three fractions of the solid phase at 35, 45 and 55 pct; two compression velocities at 30 and 300 mm s-1; and four different compression pressures—100, 150, 200 and 250 MPa. The thin plate's formability is enhanced at higher punch velocity for compressing the slurry, and fine solid particles are uniformly distributed, which in turn, enhances the plate's mechanical properties. The pressure between 150 and 200 MPa is an appropriate condition to form thin plates. A thin plate without defects can be created when the slurry at 35 pct of the solid fraction (f s) was applied at the compression velocity of 300 mm s-1 and 150 MPa of pressure. The surface state of thin plate is excellent with 220 MPa of tensile strength and 13.5 pct of elongation. The primary particles are fine over the entire plate, and there are no liquid segregation-related defects.

  3. Influence of segregations and hydrogen flakes on the mechanical properties of forged RPV steels

    International Nuclear Information System (INIS)

    Eiselt, C.C.; May, J.; Hein, H.

    2013-01-01

    In the frame of relevant 1970s/80s German research programs (e.g. FKS research program on component safety and others), many investigations on large forgings manufactured from Reactor Pressure Vessel (RPV) materials such as 20 MnMoNi 5 5 and 22 NiMoCr 3 7 have been performed. Lately, after ultrasonic testing hydrogen flakes in connection with segregation zones have been observed in a few RPV forgings. The earlier R and D programs contained a number of special heats, which covered a defined defect state (lower bound heats) with relevance to the recent observations of numerous UT indications in RPV forgings of two PWRs. Therefore, the results of these former research programs were now reviewed. The studies included an evaluation of the effects of macro/micro segregations as well as hydrogen flakes on the mechanical properties. As part of the mechanical technological experiments Charpy impact tests in different orientations (e.g. L-T, T-L and S-T) together with fracture mechanics and large scale tensile tests were carried out in segregated and non segregated material zones. In this context the letters L,T,S indicate the longitudinal, transversal and short transverse (thickness) direction with respect to rolling direction of the forging axis. The first letter indicates the direction of the principal stress, while the second letter stands for the crack propagation direction [1]. Furthermore the irradiation behavior of segregated material regions was analyzed and compared to non segregated material regions. Key results of these analyses indicate that in most cases upper shelf levels are lowered in segregated material parts compared to non segregated areas. In addition the segregations cause a larger scattering of impact energies. A high hydrogen content in combination with segregations has overall detrimental effects on the mechanical properties. However, there seems to be no specific segregation influence on the materials' irradiation reaction.

  4. Paradigmas en progressie in die teologie: *n Perspektief op die ...

    African Journals Online (AJOL)

    Die metodologie as besinningsterrein word egter al belangriker. Gedurende die tweede week van April 1988 het teoloë van dwarsoor Suid-. Afrika by die nuwe gebou van die Raad vir Geesteswetenskaplike Navorsing in. Pretoria byeen gekom vir 'n kongres van amper drie dae met die tema Paradigma.'> 476. ISSN 0259 ...

  5. Best possible heat treatment of steel SA 336 F22 for the production of forged shells with heavy walls

    International Nuclear Information System (INIS)

    Badeau, J.P.; Poitrault, I.S.; De Badereau, A.; Blondeau, R.P.

    1986-01-01

    The manufacturing of thick-wall components, such as shells, for petrochemical reactors normally requires the 2.25Cr-1Mo(SA 336 F22) steel. This paper deals with: 1. Experienced difficulties in producing thick-wall forgings up to a thickness of 500 mm with standard 2.25Cr-1Mo steel. 2. The solutions offered by Le Creusot Heavy Forge. The studies discussed are: (1) the effect of the structure; (2) the effect of the chemical composition on hardenability and temper embrittlement in steel making; and (3) the effect of austenitization conditions. Some examples concerning industrial forgings are presented, among them: 1. The manufacturing of shells for the petrochemical industry. 2. A thick-wall shell from a 146-metric ton hollow ingot

  6. DIE PERSOON VAN VREDE IN DIE SENDING

    African Journals Online (AJOL)

    aan dat 'n lewe onder die gesag van God tot volle vrede lei: “In coming under the rule of Yahweh, moreover, life was made whole and safe.” Dit is spesifiek in die tempel waar die volheid van God se vrede ondervind word (1997:662):. The temple is indeed the place where Israel entered into Yahweh's full zone of shalom.

  7. Hot Deformation Behavior and Pulse Current Auxiliary Isothermal Forging of Hot Pressing Sintering TiAl Based Alloys.

    Science.gov (United States)

    Shi, Chengcheng; Jiang, Shaosong; Zhang, Kaifeng

    2017-12-16

    This paper focuses on the fabrication of as-forged Ti46.5Al2Cr1.8Nb-(W, B) alloy via pulse current auxiliary isothermal forging (PCIF). The starting material composed of near gamma (NG) microstructure was fabricated by adopting pre-alloyed powders via hot pressing sintering (HPS) at 1300 °C. Isothermal compression tests were conducted at a strain rate range of 0.001-0.1 s -1 and a temperature range of 1125-1275 °C to establish the constitutive model and processing map. The optimal hot deformation parameters were successfully determined (in a strain rate range of 10 -3 -2.5 × 10 -3 s -1 and temperature range of 1130-1180 °C) based on the hot processing map and microstructure observation. Accordingly, an as-forged TiAl based alloy without cracks was successfully fabricated by PCIF processing at 1175 °C with a nominal strain rate of 10 -3 s -1 . Microstructure observation indicated that complete dynamic recrystallization (DRX) and phase transformation of γ→α₂ occurred during the PCIF process. The elongation of as-forged alloy was 136%, possessing a good secondary hot workability, while the sintered alloy was only 66% when tested at 900 °C with a strain rate of 2 × 10 -4 s -1 .

  8. Etiese perspektiewe op haatspraak in die lig van die derde gebod

    Directory of Open Access Journals (Sweden)

    Jakobus M. (Koos Vorster

    2014-03-01

    Full Text Available Hierdie artikel fokus op die implikasies van die derde gebod met betrekking tot haatspraak in Suid-Afrika (SA vandag. Die artikel gaan uit van die standpunt dat die name van God op sy wese dui. Die name van God soos dit in die bybelse openbaringsgeskiedenis ontwikkel word, druk die gemeenskapskarakter van God se verhouding met mense en die skepping uit. Die betekenis van die name kulmineer in die Nuwe-Testamentiese uitdrukkings Vader en God is liefde. Alle verbale gedrag wat hierdie gemeenskaps- en liefdesverhouding inhibeer, oortree die derde gebod. Die misbruik van die Naam van God vind onder andere plaas wanneer mense, wat na die beeld van God geskep is, gedegradeer word deur haatspraak, omdat sodanige degradering die gemeenskap en liefde tussen God en die mens skend. Ten slotte word sekere gevalle van haatspraak soos dit vandag in Suid-Afrika voorkom, teologies-eties belig teen die agtergrond van die betekenis van die derde gebod. Hierdie vorms sluit religieuse, rassistiese, xenofobiese, seksistiese en homofobiese haatspraak in. This article focuses on the implications of the third commandment for hate speech in modern-day South Africa. The article contends that the names of God are expressions of his Being. The names of God as they are developed in the biblical history of revelation express his creation of covenantal community and restored relations with humankind and creation. The meaning of the names of God culminates in the New Testament expressions Father and God is love. Verbal actions that inhibit the new community created by God or violate love transgress the third commandment. Misuse of the name of God occurs among others when people, created in the image of God, are verbally degraded by hate speech because such degradation violates the community of love between God and humankind. In conclusion, the article indicates forms of hate speech in South Africa that should be dealt with in the light of the third commandment. These are acts

  9. Evaluación de indicadores subjetivos durante el diseño optimo con objetivos múltiples de herramientas para la conformación de metales // Evaluating subjective character indicators in the process of multiple objective metal conforming die design

    Directory of Open Access Journals (Sweden)

    J. Arzola Ruiz

    2001-01-01

    Full Text Available En este trabajo se exponen de forma breve la aplicación de un Enfoque Integrador para el Análisis y la Síntesis de Sistemas deIngeniería para la Preparación y Toma de Decisiones bajo Criterios Múltiplesa la generación de tecnologías de conformación demetales en el ejemplo de dos sistemas desarrollados por el Centro de Estudios CAD/CAM en colaboración con la Unidad DocenteMetalúrgica del ISPJAE en los que se utiliza el dibujo paramétrico tridimensional. Se trata del sistema TROQUEL, el que permite eldiseño de troqueles de corte y punzonado simples y progresivos y del sistema DiesFor, el que permite el diseño de estampas de Forja,determinando y diseñando las herramientas para las etapas intermedias necesarias, en el proceso. Con el fin de una correcta evaluaciónde las opciones de solución ofertadas ambos sistemas brindan como resultado dibujos paramétricos de cada uno de los elementos, asícomo, los planos de conjunto y despiece correspondientes.Palabras claves: Optimización multiobjetivo, deformación plástica, cad/cam, troqueles, forja._____________________________________________________________________________Abstract:In this work are exposed, in a brief way, the application of an integrative approach for the analysis and synthesisengineering systems for preparation and making decisions under multiple criterions for metal conforming technologies with the example of two concrete systems developed by CAD/CAM's Studies Center of HolguinUniversity in collaboration with the Department of Metallurgy of José Antonio Echeverría Polytechnical Institutein which three-dimensional parametric drawing are used. The examples are: system DIE, which allows the designand progressive cutting dies and the system DiesFor, the one that allows the design of Forge Die, determiningand designing the tools for the necessary intermediate stages in the process. With the purpose of a correctevaluation of the offered solution options, both systems

  10. Evolution of the Ultrasonic Inspection of Heavy Rotor Forgings Over the Last Decades

    Science.gov (United States)

    Zimmer, A.; Vrana, J.; Meiser, J.; Maximini, W.; Blaes, N.

    2010-02-01

    All types of heavy forgings that are used in energy machine industry, rotor shafts as well as discs, retaining rings or tie bolts are subject to extensive nondestructive inspections before they are delivered to the customer. Due to the availability of the parts in simple shapes, these forgings are very well suited for full volmetric inspections using ultrasound. In the beginning, these inspections were carried out manually, using straight beam probes and analogue equipment. Higher requirements in reliability, efficiency, safety and power output in the machines have lead to higher requirements for the ultrasonic inspection in the form of more scanning directions, higher sensitivity demands and improved documentation means. This and the increasing use of high alloy materials for ever growing parts, increase the need for more and more sophisticated methods for testing the forgings. Angle scans and sizing technologies like DGS have been implemented, and for more than 15 years now, mechanized and automated inspections have gained importance since they allow better documentation as well as easier evaluation of the recorded data using different views (B- C- or D-Scans), projections or tomography views. The latest major development has been the availability of phased array probes to increase the flexibility of the inspection systems. Many results of the ongoing research in ultrasonic's have not been implemented yet. Today's availability of fast computers, large and fast data storages allows saving RF inspection data and applying sophisticated signal processing methods. For example linear diffraction tomography methods like SAFT offer tools for 3D reconstruction of inspection data, simplifying sizing and locating of defects as well as for improving signal to noise ratios. While such methods are already applied in medical ultrasonic's, they are still to be implemented in the steel industry. This paper describes the development of the ultrasonic inspection of heavy forgings

  11. Ungewöhnliche Kundengruppe? Informationskompetenz-Veranstaltungen für die Universitätsverwaltung

    Directory of Open Access Journals (Sweden)

    Caroline Leiß

    2014-12-01

    Full Text Available Die Universitätsbibliothek der Technischen Universität München (TUM bietet mit jährlich ca. 400 Veranstaltungen und 6.000 Teilnehmern ein umfangreiches Programm im Bereich Informationskompetenz an. Die Kunden sind in der Regel Studierende bzw. Angehörige der Fakultäten oder Schüler/innen und Lehrer/innen. Seit mehreren Jahren wird eine weitere Kundengruppe gezielt angesprochen: die Mitarbeiter/innen der Universitätsverwaltung und der TUM-Serviceeinrichtungen. Immobilienmanagement, Personalabteilung, Rechtsabteilung, Personalrat, Sicherheitsbeauftragte, Campus Feuerwehr: Inwieweit sind den Beschäftigten dieser Bereiche die Dienstleistungen bekannt, die über die Universitätsbibliothek genutzt werden können? Wissen die Kolleginnen und Kollegen überhaupt, dass die Bibliothek sie bei Literaturrecherche und -beschaffung unterstützen würde? Die Informationsveranstaltungen für diese Einrichtungen werden in enger Absprache mit der jeweils eingeladenen Gruppe bedarfsbezogen geplant. Sie enthalten eine Führung durch die Magazine und einen Schulungsteil, in dem ausreichend Zeit für Fragen und Diskussionen vorhanden ist. The University Library of Technische Universität München (TUM offers a comprehensive information literacy programme with approximately 400 events and 6,000 participants every year. The participants are usually students, faculty staff or secondary school students and teachers. For some time, however, another target group has been specifically addressed: staff members of the university administration and service facilities, such as Property Management, Human Resources, Legal Department, Staff Council, security officers, Campus Fire Department: To what extent are the employees of these areas familiar with the services of the university library? Are they aware that the library offers help with their literature search, document delivery or information processing? For several years, the university library has been actively

  12. Die era van Suid-Afrika se militere hoogbloei met die ...

    African Journals Online (AJOL)

    4 Jun 1976 ... Die Toyota 1200 bakkie is geadverteer met die woorde 'Hier kom die pantserbakkie', teen die agtergrond van 'n olifant tenk.32. Daar is ook 'n betrekking deur Thorold en van Wyk geadverteer waar militere opleiding 'n voorvereiste was.33. Daar was ook films wat weermag en polisie gebasseer is wat in die ...

  13. ’n Etiek van liefde: Die etiese perspektiewe van die Heidelbergse Kategismus

    Directory of Open Access Journals (Sweden)

    Koos Vorster

    2013-06-01

    Full Text Available Hierdie artikel behandel die etiese perspektiewe van die Heidelbergse Kategismus – een van die prominente belydenisskrifte in die gereformeerde tradisie. Die etiese relevansie is ingebed in die konfessie se verklaring van die tien gebooie. Die artikel verduidelik dat die etiek van die Heidelbergse Kategismus ten diepste ’n karakteretiek is en dat dit gelowiges oproep tot ’n etiek van liefde. Hierdie liefde sluit in liefde vir die verbondsgemeenskap, die bediening van die Woord, die heiligheid van God en die waardigheid van mense, die gemeenskap van die gelowiges, gesag, die lewe, die huwelik, privaatbesit en arbeid asook waarheid en geregtigheid. As gevolg van die sinekdogeekarakter van die wet is hierdie etiek van liefde vandag baie relevant. This article deals with the ethical relevance of one of the prominent confessions in the reformed tradition, namely the Heidelberg Cathechism. The ethical relevance lies in the confession’s elucidation of the ten commandments and its application to moral conduct. The article explains that the ethics of the Heidelberg Catechism is essentially a virtue ethics calling for an ethics of love. This love should include love for the covenantal communion, ministry of the Word, the holiness of God and the dignity of people, the communion of the saints, authority, life, marriage, private property and labour, and truth and justice. Due to the synecdochical character of the ten commandments this ethics of love is highy relevant in the present times.

  14. Die invloed van herbivorie en vuur op die oorlewing van sekere meerjarige kruide langs die Sabierivier, Kruger Nasionale Park

    Directory of Open Access Journals (Sweden)

    H. Myburgh

    2012-03-01

    Full Text Available Die groot vloede wat in die jaar 2000 in die Kruger Nasionale Park plaasgevind het, het dierivieroewerplantegroei versteur. Dit het die geleentheid gebied om heinings op te rig langsdie Sabierivier om herbivore uit sekere gebiede uit te sluit en sodoende die herstel van die rivieroewerekosisteme te monitor.

  15. GOSPEL MOTIVES IN THE DYING NOTES OF NIKOLAI GOGOL

    OpenAIRE

    Vladimir Dmitrievich Denisov

    2012-01-01

    The article analyses several notes made by Nikolai Gogol shortly before his death in the light of their links to his other works and the Gospel text. The author seems to have understood that he was dying and was preparing to meet his death as a Christian should, to an extent matching the events around him with those in the Gospel. His artistic eye and hand did not fail him. His dying notes feature a brief sketch of a man in a cab and a profile of a man being shut by a closing book. Calligraph...

  16. Engine piston assembly and forged piston member therefor having a cooling recess

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, B.C.; Erickson, K.L.; Green, J.A.; Nyez, D.S.

    1989-09-19

    This patent describes a forged steel piston member for reciprocating movement in an engine. It comprises: an upper portion of substantially cylindrical shape and having a central axis, a top surface, a tubular wall depending from the top surface and having a peripheral groove adapted to receive a sealing ring, a lower end surface, and an inwardly facing wall surface extending upwardly from the lower end surface. The upper portion further includes an outwardly facing wall surface spaced radially inwardly from the inwardly facing wall surface and a downwardly facing transition portion blendingly associated with the inwardly and outwardly facing wall surfaces to collectively define an annular cooling recess, the transition portion being elevational spaced a relatively short distance from the top surface; and the inwardly facing wall surface being a machined surface of revolution about the central axis integral or one-piece forging.

  17. FE-simulation of hot forging with an integrated heat treatment with the objective of residual stress prediction

    Science.gov (United States)

    Behrens, Bernd-Arno; Chugreeva, Anna; Chugreev, Alexander

    2018-05-01

    Hot forming as a coupled thermo-mechanical process comprises numerous material phenomena with a corresponding impact on the material behavior during and after the forming process as well as on the final component performance. In this context, a realistic FE-simulation requires reliable mathematical models as well as detailed thermo-mechanical material data. This paper presents experimental and numerical results focused on the FE-based simulation of a hot forging process with a subsequent heat treatment step aiming at the prediction of the final mechanical properties and residual stress state in the forged component made of low alloy CrMo-steel DIN 42CrMo4. For this purpose, hot forging experiments of connecting rod geometry with a corresponding metallographic analysis and x-ray residual stress measurements have been carried out. For the coupled thermo-mechanical-metallurgical FE-simulations, a special user-defined material model based on the additive strain decomposition method and implemented in Simufact Forming via MSC.Marc solver features has been used.

  18. Chrístologie: Die historiese Jesus en die kerugmatiese Christus by ...

    African Journals Online (AJOL)

    dige Here van sy kerk. Die Christelike teologie en die kerk het dus nie 'n ander oprsprong as wat die Christologiese belydenis van die oer-Christendom het nie, naamlik die paasgebeure. Schmithals (1972b:77) wil kerk en teologie aanmoedig om hierdie oorsprong in gedagte te hou en om goed te besef dat die Christus-.

  19. Die invloed van gesondheidsopvoeding op die prevalensie van skistosoombesmettings by leerders in ’n skistosoom - endemiese gebied in die Limpopoprovinsie

    Directory of Open Access Journals (Sweden)

    Corrie Wolmarans

    2008-09-01

    Full Text Available In hierdie studie is geselekteerde direkte en indirekte onderrigmetodes geëvalueer ten opsigte vanhulle potensiaal om die prevalensie van skistosoombesmettings by skoolgaande kinders, woonagtigin ’n landelike omgewing in ’n skistosoom-endemiese gebied, te verlaag. Twee direkte (poppekas enblaaibord en drie indirekte (plakkaat, kennisgewingbord en onderrig via ouers of voogdeonderrigmetodes is geëvalueer.Skistosoombesmette leerders is met behulp van parasitologiese metodes geïdentifiseer en aan ’nvraelys in hul moerdertaal onderwerp om onder andere op hoogte van hulle kennis ten opsigte vanskistosomose te kom en te bepaal hoe die infrastruktuur tot hulle beskikking wat water en sanitasiebetref, daar uitsien. Leerders is met behulp van plaaslike gesondheidspersoneel vir die siekte behandelen daarna op verskeie geleenthede in samewerking met plaaslike onderwysers aan die verskillendeonderrigmetodes blootgestel.’n Aansienlike toename in die leerders se kennis aangaande skistosomose is reeds na die tweedeonderrigsessie waargeneem. Ten spyte van die feit dat die leerders in ’n skistosoom-endemiesegebied woonagtig was, het slegs 2% die siekte met ’n natuurlike waterhabitat soos ’n rivier geassosieer.Daar is verder gevind dat relevante amptelike strukture soos klinieke, geneeshere en skole byna geenrol speel in die verskaffing van inligting van wat die siekte behels en hoe dit oorgedra word nie.Betekenisvolle afnames in die kumulatiewe prevalensie van besmetting het by al die groepe, wat aandie onderskeie onderrigmetodes blootgestel was gedurende die ondersoek, voorgekom, wanneer ditmet die kontrolewaarde waar die leerders geen onderrig ontvang het nie, vergelyk is. Statistiesevergelykings tussen die verskillende onderrigmetodes het getoon dat die poppekas, blaaibord enplakkaat die effektiefste was om die prevalensie te verlaag, terwyl die gebruik van ouers of voogdedie minste effektief was. Alhoewel die kumulatiewe prevalensie van

  20. Study on antioxidant experiment on forged steel tube sheet and tube hole for steam generator

    International Nuclear Information System (INIS)

    Zong Hai; Wang Detai; Ding Yang

    2012-01-01

    Antioxidant experiment on forged steel tube sheet and tube hole for steam generator was studied and the influence of different simulated heat treatments on the antioxidant performance of tube sheet and tube hole was made. The influence of different antioxidant methods on the size of tube hole was drawn. Furthermore, the change of size and weight of 18MnD5 forged steel tube sheet on the condition of different simulated heat treatments was also studied. The analytical results have proved reference information for the use of 18MnD5 material and for key processes of processing tube hole and wearing and expanding U-style tube. (authors)

  1. Social Work and Engineering Collaboration: Forging Innovative Global Community Development Education

    Science.gov (United States)

    Gilbert, Dorie J.

    2014-01-01

    Interdisciplinary programs in schools of social work are growing in scope and number. This article reports on collaboration between a school of social work and a school of engineering, which is forging a new area of interdisciplinary education. The program engages social work students working alongside engineering students in a team approach to…

  2. duele verse sowel as die somtotaal die leser

    African Journals Online (AJOL)

    27 Jan 2006 ... selfs 'n landkaart afgedruk) terwyl dit ter- selfdertyd ver bo die lokale uitstyg. Die digter is sterk bewus van sy omgewing, geskiedenis en tradisies, maar veral van die algemene menslike kondisie wat binne hierdie referensiekader vergestalt word. Hy gebruik 'n bekende historiese slagveld as bundeltitel (en ...

  3. Paulus as vredemaker. Oor die resepsie van die Brief aan Filemon ...

    African Journals Online (AJOL)

    7 Jul 2015 ... Inleiding. Die woord 'vrede' kom net een maal in die Filemonbrief voor, en wel in die aanhef van die brief. Kommentatore merk egter gereeld op dat 'n mens nie daaruit moet aflei dat dié begrip onbelangrik vir die verstaan van die brief is nie. Om een voorbeeld te noem: Barth en Blanke. (2002) skryf as volg:.

  4. Die wet is evangelie: Die Heidelbergse Kategismus steeds aktueel na 450 jaar

    Directory of Open Access Journals (Sweden)

    Piet Strauss

    2013-09-01

    Full Text Available In die denke van Martin Luther bestaan daar spanning tussen die wet van God en die evangelie. Vir Luther is liefde die eie werk en die wet die vreemde werk van God. Daarteenoor integreer of versoen Johannes Calvyn God se wet met die evangelie. Hy vertolk die openingswoorde van die wet byvoorbeeld as liefdevol en bevrydend en daarom evangelies. Calvyn beskou die wet as die manier waarop ’n Christen sy liefde vir God uitleef en sy dankaarheid teenoor God vir sy verlossing betoon. Calvyn se siening oor die verhouding tussen die wet en die evangelie het ’n betekenisvolle invloed op die Heidelbergse Kategismus se formulering ten opsigte van hierdie saak. Volgens die Kategismus is die wet evangelie, of die vorm wat die evangelie in die lewe van die mens aanneem. In the thought of Martin Luther tension exists between the law of God and the gospel. Luther regards love as the own work of God and the law as something strange to the Lord. John Calvin, however, integrates Gods law and the gospel to the extent that the opening words of the ten commandments are regarded as words of love and redemption and therefore evangelical. To Calvin the law becomes the way in which a converted Christian lives and shows his gratitude to God for his salvation. Calvin’s view on the relationship between law and gospel had a significant influence on the way in which the Heidelberg Cathecism formulates these two concepts. For the Cathecism the law is gospel or the form in which the gospel takes shape in human life.

  5. Forgings made of austenitic chromium-nickel steels for the low temperature range

    International Nuclear Information System (INIS)

    Gruendler, O.; Schwarz, W.; Koren, M.

    1981-01-01

    The authors discuss the low temperature application of austenitic chromium-nickel steels for energy production and process techniques. Material requirements are presented, and the behaviour, mechanical and physical properties of such steels are discussed. The manufacture of forgings is considered and test results presented. (Auth.)

  6. Forgings made of austenitic chromium-nickel steels for the low temperature range

    Energy Technology Data Exchange (ETDEWEB)

    Gruendler, O.; Schwarz, W.; Koren, M. (Vereinigte Edelstahlwerke A.G. (VEW), Kapfenberg (Austria))

    1981-09-01

    The authors discuss the low temperature application of austenitic chromium-nickel steels for energy production and process techniques. Material requirements are presented, and the behaviour, mechanical and physical properties of such steels are discussed. The manufacture of forgings is considered and test results presented.

  7. Fatigue and fracture behavior of low alloy ferritic forged steels

    International Nuclear Information System (INIS)

    Chaudhry, V.; Sharma, A.K.; Muktibodh, U.C.; Borwankar, Neeraj; Singh, D.K.; Srinivasan, K.N.; Kulkarni, R.G.

    2016-01-01

    Low alloy ferritic steels are widely used in nuclear industry for the construction of pressure vessels. Pressure vessel forged low alloy steels 20MnMoNi55 (modified) have been developed indigenously. Experiments have been carried out to study the Low Cycle Fatigue (LCF) and fracture behavior of these forged steels. Fully reversed strain controlled LCF testing at room temperature and at 350 °C has been carried out at a constant strain rate, and for different axial strain amplitude levels. LCF material behavior has been studied from cyclic stress-strain responses and the strain-life relationships. Fracture behavior of the steel has been studied based on tests carried out for crack growth rate and fracture toughness (J-R curve). Further, responses of fatigue crack growth rate tests have been compared with the rate evaluated from fatigue precracking carried out for fracture toughness (J-R) tests. Fractography of the samples have been carried out to reveal dominant damage mechanisms in crack propagation and fracture. The fatigue and fracture properties of indigenously developed low alloy steel 20MnMoNi55 (modified) steels are comparable with similar class of steels. (author)

  8. Die gebruik van die mite in Die werfbobbejaan van Alexander Strachan

    Directory of Open Access Journals (Sweden)

    E. M.M. Klopper

    1996-05-01

    Full Text Available The use of myths in Die werfbobbejaan by Alexander Strachan This article focuses on the rote of Zulu myths in Alexander Strachan’s novel Die werfbobbejaan. It lakes as point of departure sources on mythology like Cuddon (1991, Baldick (1990, Grimal (1969, Levi-Strauss (1979 and Jung (1969. Die werfbobbejaan essentially recounts the story of a man (the adventurer, the academic, the writer, the hunter who also is the central character in Strachan's two preceding novels. Die werfbobbejaan focuses on the completion of an individuation process in the life of the central character, a process already begun in the preceding two novels and which in this novel finally culminates in the confrontation between hunter and baboon. The completion of this process is facilitated by the African milieu of Zululand where people give meaning to their existence by means of myths, and where no distinction is made between the mythic and rational modes of experiencing reality.

  9. N HERSIENING VAN DIE AFRIKAANSE VERTALING VAN DIE ...

    African Journals Online (AJOL)

    Test

    aangetoon het, 'n huis in Kapernaum gehad en hierdie geskiedenis speel in Kapernaum of daar digby af. Jesus en sy dissipele het namelik, volgens 6:35 geland by Gennesaret, net suid van Kapernaum Die gevolgtrekking word ondersteun deur Joh. 6:17 waarvolgens die dissi pele na die spysiging op Kapernaum gevaar ...

  10. Die dinamika van die beperkte drie-deeltjie-probleem in sterrekunde

    Directory of Open Access Journals (Sweden)

    Keegan D. Anderson

    2011-09-01

    Full Text Available Die beperkte drie-deeltjie-probleem is een van die oudste probleme in klassieke fisika en is alvir ongeveer die afgelope honderd jaar bestudeer. Die probleem is nie oplosbaar op ‘n geslote analitiese wyse nie, alhoewel ’n oneindige reeks oplossing bestaan.

  11. Die taak van akademiese geletterdheid/hede binne die konteks van ...

    African Journals Online (AJOL)

    Opsomming. Die vestiging van Akademiese Geletterdheid by tersiêre instansies in Suid-Afrika het gegroei uit die besef dat 'n goedontwikkelde akademiese taalvermoë essensieel is vir akademiese prestasie. Gepubliseerde literatuur getuig van die belangrike verskuiwings wat oor die afgelope aantal dekades plaasgevind ...

  12. Effect of precipitates on microstructures and properties of forged Mg-10Gd-2Y-0.5Zn-0.3Zr alloy during ageing process

    International Nuclear Information System (INIS)

    Han, X.Z.; Xu, W.C.; Shan, D.B.

    2011-01-01

    Highlights: · The effect of forging process on microstructure evolution and mechanical properties of Magnesium alloy with rare earth was investigated. · The optimal mechanical properties of the alloy with high strength and enough elongation were obtained after forging and ageing process. · The strength improvement of the alloy after forging and ageing process mainly results from the precipitation of 14H-type LPSO phase. · Strengthening mechanism of the alloy is controlled by the precipitation of β' and 14H-type LPSO phases which can inhibit sliding of dislocations and growth of grain boundaries. - Abstract: The precipitate behavior during forging and ageing process of Mg-10Gd-2Y-0.5Zn-0.3Zr alloy has been investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The mechanical properties of the alloy after forging and ageing process have been evaluated using Vickers hardness and room-temperature tensile tests. The results show that precipitation of 14H-type long period stacking order (LPSO) phase is the main strengthening phase in the as-forged alloy. The LPSO phase and refinement of grains contribute to the strength improvement of the alloy after forging process. The optimal mechanical properties of the alloy are obtained when it is aged at 200 deg. C for 60 h, which mainly owes to the precipitation of large amounts of β' and 14H-type LPSO phases on the α-Mg matrix. The growth of secondary phases, widening of soft precipitate free zones and coarsening of grains during subsequent ageing process at higher temperature lead to the decrease of mechanical properties of the alloy.

  13. Die 'postmoderne' stempel in die Nuwe-Testamentiese hermeneutiek

    African Journals Online (AJOL)

    georiënteerde teorie en kritiek wat volgens Moore opbou tot 'n herhaling binne. Bybelnavorsing. Dit het reeds by Immanuel Kant begin. Sedert Kant is dit proble- maties cm die objek van kennis te beskou as iets wat kennis objektief in sigself bevat. Objektiwisme is prys gegee. Dialektiek het in die plek daarvan gekom. Die.

  14. DIE KONINGSBEDE AS ELEMENT IN DIE KRONINGSRITUEEL. By ...

    African Journals Online (AJOL)

    Test

    Die offerfees te Gibeon was 'n plegtigheid, waaraan geheel Israel deelgeneem het. Die duisend. "brandoffers" wat sowel Kon. as Kron. vermeld, sal wel opgevat moet word as „brandoffers en dankoffers", sodat daar vir die aanwesiges. *n groot feesmaaltyd aangerig is, vgl. I Kon. 3:15. n Sodanige maal- tyd verbind vors en ...

  15. Quantenfische die Stringtheorie und die Suche nach Weltformel

    CERN Document Server

    Lüst, Dieter

    2011-01-01

    Lässt sich das Verhalten aller Dinge, von den kleinsten Teilchen bis zum Universum, einheitlich beschreiben? Der heißeste Kandidat für die Entwicklung einer Weltformel, die alle physikalischen Phänomene erklären kann, ist die Stringtheorie. Sollte sie sich als richtig erweisen, so würde das unser Verständnis über den Ursprung der Naturgesetze dramatisch verändern. Denn das von uns beobachtete Universum wäre dann vermutlich eine winzige Blase in einem viel größeren Gebilde, dem Multiversum. Um die Stringtheorie und die Idee des Multiversums plausibel zu machen, greift der international bekannte theoretische Physiker Dieter Lüst auf ein Modell zurück: das Leben von Fischen in einem Teich. Eines Tages gelingt es den Fischen, die kleinsten Teilchen zu identifizieren, aus denen alles im Fischteich besteht - eingeschlossen sie selbst. Sie nennen diese Urbausteine Quantenfische, da ihr Verhalten nahelegt, dass sie auch eine Art von Lebewesen sind. Doch der ersten folgt eine weitere Entdeckung der Fisch...

  16. Van die Gasredakteur

    African Journals Online (AJOL)

    cherish and teach.'1. Die Fakulteit Geneeskunde van die Universiteit van die Oranje-Vrystaat het pragtig gegroei ge- durende die eerste 21 jaar van sy bestaan. Die entoesiasme, doelgerigtheid, harde werk en inisia- tiewe van 'n groot aantal persone was hiervoor verantwoordelik. 'If we see a bit more clearly than they, it is ...

  17. Forging C-C Bonds Through Decarbonylation of Aryl Ketones.

    Science.gov (United States)

    Somerville, Rosie J; Martin, Ruben

    2017-06-06

    The ability of nickel to cleave strong σ-bonds is again in the spotlight after a recent report that demonstrates the feasibility of using nickel complexes to promote decarbonylation of diaryl ketones. This transformation involves the cleavage of two strong C-C(O) bonds and avoids the use of noble metals, hence reinforcing the potential of decarbonylation as a technique for forging C-C bonds. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  18. Die benutting van vraelyste met die oog op meer effektiewe ...

    African Journals Online (AJOL)

    UPuser

    effektiewe stresbeheer as een van die temas te hanteer. Op grond van die navorsing deur onder andere Lawson (1985) en Taylor (1999) sou ek graag die proses van differensiasie2 ook by genoemde lys voeg as tema vir bespreking tydens huweliksvoorbereiding. 2 Differensiasie kan beskryf word as die losmaakproses ...

  19. Wêreldmededingendheid en die tegnologie

    Directory of Open Access Journals (Sweden)

    C. W. I. Pistorius

    1996-07-01

    Full Text Available Afgesien van die interne uitdagings wat die Heropbou- en Ontwikkelingsprogram (HOP aan Suid-Afrika bied, moet die land ook tred hou met die veranderende globale omgewing, spesifiek die toenemende belangrikheid van ekonomiese sekuriteit as komponent van nasionale sekuriteit. Die konsep van mededingendheid vergestalt die doelwit wat nagestreef moet word ten einde die ontluikende globale ekonomiese stryd aan te durf. As ’n belangrike drywer van ekonomiese welvaart is tegnologie een van die belangrikste sleutels tot internasionale mededingendheid. Tegnologiese innovasie is die proses wat as hefboom hiervoor gebruik moet word. Dit is egter nodig dat tegnologie, en spesifiek die proses van tegnologiese innovasie, formeel en gestruktureerd bestuur moet word, sowel op nasionale as firmavlak. Op nasionale vlak is die voorsiene Nasionale Innovasiestelsel beslis ’n stap in die regte rigting.

  20. die kasteel••de goede hoop" (1921.1923): die verhaal van in ...

    African Journals Online (AJOL)

    3. TWEE. KOMITEE-VERGADERINGS. BESLUITE a. Doel en samestelling van die komitee. Op 12 Desember 1921 stuur die Sekretans yap Verdediging uitnodigings aan sekere amptelike instansies en ander behingstd1endes waarin hy die redes vir die wenslikheid van 'n komitee en die werksaamhede uitecnsit en die ge-.

  1. ontwikkeling van die gemenereg in die lig van artikels 39(2)

    African Journals Online (AJOL)

    Administrator

    'n Mens kan met reg vra of die ius connubiorum van Brouwer en die Law of. Husband and Wife van ... AD 560 (Geheime Raad) 563. 5 Sien vir besonderhede Hahlo en Kahn SA Legal System and its Background 304. ..... Die Franse chemikus, Antoine Lavoisier, is in 1794 tydens die Franse revolusie tereggestel. Terwyl die ...

  2. Die relevansie van die boek Prediker

    African Journals Online (AJOL)

    ook in die dogmatiek te bespeur is nie. 'n Vinnige oorsig oor die teksverwysings van. 'n paar wydgelese dogmatiekhandboeke kan dit bevestig. In Karl Barth se omvang- ryke Kirchliche Dogmatik word Prediker slegs vyf en dertig maal aangehaal en slegs sewe maal word teksgedeeltes bespreek. Emil Brunner haal Prediker ...

  3. Die wonders in Johannes 6 verklaar aan die hand van 'n ...

    African Journals Online (AJOL)

    Maar die Evangelie van Johannes gee self 'n aanduiding van wat die intensie van die geskrif is, te wete Johannes 20: 30-31: Jesus het nog baie ander wondertekens, wat nie in hierdie boek beskrywe is nie, voor sy dissipels gedoen. Maar hierdie wonder tekens is beskrywe sodat julle kan glo dat Jesus die Christus is, die.

  4. Packaged die heater

    Science.gov (United States)

    Spielberger, Richard; Ohme, Bruce Walker; Jensen, Ronald J.

    2011-06-21

    A heater for heating packaged die for burn-in and heat testing is described. The heater may be a ceramic-type heater with a metal filament. The heater may be incorporated into the integrated circuit package as an additional ceramic layer of the package, or may be an external heater placed in contact with the package to heat the die. Many different types of integrated circuit packages may be accommodated. The method provides increased energy efficiency for heating the die while reducing temperature stresses on testing equipment. The method allows the use of multiple heaters to heat die to different temperatures. Faulty die may be heated to weaken die attach material to facilitate removal of the die. The heater filament or a separate temperature thermistor located in the package may be used to accurately measure die temperature.

  5. Die teologie in gesprek met die ekonomie

    African Journals Online (AJOL)

    (1723-1790) sy vertrekpunt neem, ontwikkel, as oorwinnaars uit die Franse Revolu .... Die onmiddellike sukses van Adam Smith se 'Wealth of Nations' was .... alle vorme van sosialisme niks anders as 'kommunisme' (Wassenaar 1977:12) nie.

  6. Die evaluering van 'n bestuursopleidingskursus met behulp van die posmandjie-tegniek

    Directory of Open Access Journals (Sweden)

    W. de Jager

    1997-06-01

    Full Text Available The evaluation of a management training course by using the in-basket technique. A management training course was evaluated for effectiveness by using two specially compiled in-basket exercises equivalent in complexity. Outcome evaluation was performed so as to determine whether learning transfer took place, ie., whether management skills in the application of planning, organising and control manifest in the work context afterwards. Significant differences were found between the experimental and the control group and were investigated by means of the "Univariate procedure". This management training course could effectively be measured with the behaviour assessment approach using two groups, where only the one group was exposed to a management training course to assess whether management behaviour changed as a result of learning transfer. This study utilises the in-basket technique as an instrument for training course evaluation. Opsomming Die effektiwiteit van 'n bestuursopleidingskursus is geevalueer aan die hand van gedragverandering soos gemeet deur twee posmandjies van dieselfde moeilikheidsgraad. Uitkomsevaluering is gedoen om te bepaal of leeroordrag plaasgevind het, met ander woorde/ of the nuut aangeleerde bestuursvaardighede in die toepassing van die bestuursdimensies beplanning, organisering en beheer wel na die tyd in die konteks van werkgedrag manifesteer. Beduidende verskille tussen die eksperimentele en die kontrole groep is gevind. Dit is ondersoek met behulp van enkelveranderiike-variansie-ontleding. Die bestuursopleidingskursus kon effektief vanuit die gedragbeoordelingsbcnadering gemeet word by twee groepe, waar slegs die een groep aan 'n bestuursopleidingskursus blootgestel word om te kon bepaal of bestuursgedrag verander het. Die studie benut die posmandjie-tegniek as kursusevalueringsinstmment.

  7. Die ontmaskering van die bose: Eksegetiese perspektiewe op ...

    African Journals Online (AJOL)

    p1243322

    2 Yarbro Collins (1983) bied tans nog die beste agtergrond vir 'n besinning oor geweld in ..... John's grammatical howlers are intentionally designed to alert listerners ..... 26 In die Nuwe Testament word Paul se snydende opmerking teenoor die Korintiërs as ..... rnt g0r`m nh8 ldfhrs`}m du sg}u fg}u + n2sh d/m sg>}} e`ql`jdh.

  8. PROF DR FELIX V. lATEGAN: Die Boer se Roer. Die Groot ...

    African Journals Online (AJOL)

    PROF DR FELIX V. lATEGAN: Die Boer se. Roer. Die Groot Geweerboek van Suid-. Afrika. Tafelberg. Uitgewers. Kaapstad, pp. 209, bibliografie, register. Sonder die Boer en sy roer is die geskiede:lis van ons land feitlik ondenkbc:wr en dit is clan ook vo/kome juis gesien dat die skrywer van hierdie baanbrekerswerk die ...

  9. Sal die ‘ewolusie’ vanaf biologie na lewenswetenskappe ‘uitsterwing’ van die vakgebied voorkom?

    Directory of Open Access Journals (Sweden)

    Johanna G. Ferreira

    2012-03-01

    Full Text Available In hierdie artikel word die wysiging van die skoolvak van ‘biologie’ na ‘lewenswetenskappe’ bespreek, asook die gepaardgaande en verwagte implikasies van die verandering. Die vraag word gestel of die beoogde wysiging wel noemenswaardig is en of dit enigsins ‘n verskil aan die dalende belangstelling in die lewenswetenskappe op tersiêre vlak sal maak. Die wysigings in die nuwe kurrikula verhoog die relevansie van die vakinhoud vir leerders en vir die gemeenskap, maar sekere kwessies kry nie aandag nie. Voorstelle word gemaak om die kurrikulum te wysig en onderrigmetodes aan te pas om die nodige vaardighede by leerders te vestig.

  10. n opinie oor die behaviouristiese siening versus die fenomenologie ...

    African Journals Online (AJOL)

    verband die eksperimente van Pavlov, Thorndike,. Skinner, Tolmann en Hull.) Fenomenologie. Die fenomenologie is 'n essensie-openbarende denkrigting. Dit impliseer'n denkende soektog na dit wat 'n besondere verskynsel of werklikheid maak juis dit wat dit is en nie iets anders nie. In die fenomenologiese antropologie ...

  11. [Research on the temperature field detection method of hot forging based on long-wavelength infrared spectrum].

    Science.gov (United States)

    Zhang, Yu-Cun; Wei, Bin; Fu, Xian-Bin

    2014-02-01

    A temperature field detection method based on long-wavelength infrared spectrum for hot forging is proposed in the present paper. This method combines primary spectrum pyrometry and three-stage FP-cavity LCTF. By optimizing the solutions of three group nonlinear equations in the mathematical model of temperature detection, the errors are reduced, thus measuring results will be more objective and accurate. Then the system of three-stage FP-cavity LCTF was designed on the principle of crystal birefringence. The system realized rapid selection of any wavelength in a certain wavelength range. It makes the response of the temperature measuring system rapid and accurate. As a result, without the emissivity of hot forging, the method can acquire exact information of temperature field and effectively suppress the background light radiation around the hot forging and ambient light that impact the temperature detection accuracy. Finally, the results of MATLAB showed that the infrared spectroscopy through the three-stage FP-cavity LCTF could meet the requirements of design. And experiments verified the feasibility of temperature measuring method. Compared with traditional single-band thermal infrared imager, the accuracy of measuring result was improved.

  12. Microstructures and tensile properties of Mg–Gd–Y–Zr alloy during multidirectional forging at 773 K

    International Nuclear Information System (INIS)

    Tang, Liechong; Liu, Chuming; Chen, Zhiyong; Ji, Dawei; Xiao, Hongchao

    2013-01-01

    Highlights: • Rare earth (RE) containing Mg–Gd–Y–Zr alloy was successfully multidirectional forged for 8 passes without any cracks. • Initial coarse grains was refined due to a combination of discontinuous and continuous dynamic recrystallization. • The alloy MDFed after 6 passes exhibited an excellent balance of strength and ductility at room temperature. - Abstract: A homogenized Mg–10Gd–4.8Y–0.6Zr (wt.%) alloy was subjected to multidirectional forging (MDF) at 773 K. It was shown that the average grain size decreased with increasing cumulative strain till 6 passes. Uniform fine-grained structure with an average grain size of 9.3 μm was achieved after 6 passes, i.e., cumulative strain of 1.8. Results revealed that grain refinement was induced by a complicated combination of discontinuous dynamic recrystallization at low strain regions and continuous dynamic recrystallization or rotation recrystallization at medium-to-high strain regions. The alloy multi-directionally forged (MDFed) for 6 passes exhibited an excellent balance of strength and ductility at room temperature with ultimate tensile strength (UTS) of 336 MPa and elongation to fracture of 21.0%

  13. The analysis of forming and strain state of the hollow step forgings during the enlarging process

    Directory of Open Access Journals (Sweden)

    Олег Євгенійович Марков

    2017-12-01

    Full Text Available Improving safety, accelerating construction and extending the life of nuclear power plants is one of the main directions of the development of the energy industry. From this point of view, much attention is being paid to the production of forgings, which combine a few details today. This requires the use of new technologies with the use of non-standard tools. The purpose of the work is analyze of the shape and the deformation state of the conical stepped forging when rolling the stepped workpiece with the simultaneous deformation of the protuberance and the ledge. The simulation was performed using finite element method, which is consistent with experimental data. Experimental studies were carried out on lead models. Rolling of stepped workpiece with simultaneous deformation of the protrusion and ledge leads to the appearance of conical forging. Taper on the side of the ledge occurs at the initial stage of rolling and during the whole process increases. The emergence of a conical shape is explained by the fact that during slipping, with the same absolute deformation (stroke, the ledge gets more accumulated deformation through a more precise wall.

  14. Die dialogiese prinsipe

    Directory of Open Access Journals (Sweden)

    J. J. de Klerk

    1981-08-01

    Full Text Available Met die dialogiese prinsipe word daardie beginsel bedoel, waarin die tweerigtingverkeer of kommunikasie onder, of met, of deur die mense op 'n heel besondere gesprekmatige wyse gere�l word. Tot die wese van die dialogiese prinsipe behoort "als Grundvoraussetzung das Ernstnehmen des Gesprachspartners und das darin enthaltene zuhoren-konnen. Dialog ist also etwas anderes als Disput oder Diskussion. Er setzt gegenseitiges Vertrauen und Hochachtung voraus."

  15. Die aanspraak op Goddelike steun in 'n konfliksituasie volgens die ...

    African Journals Online (AJOL)

    laws, and ethical or political principles. A synchronic investigation of relevant Old ... die toneel gebring met die vraag: 'aan wie se kant is God' (vgl bv The road to. Damascus 1979:6)? Volgens .... betrekking tot die Ou Testament: Hoe moet ons vasstel wie se kant God nou regtig kies, of wie veg aan die kant van God en wie ...

  16. The Forging of a White Gay Aesthetic at the Saint, 1980–84

    Directory of Open Access Journals (Sweden)

    Tim Lawrence

    2011-06-01

    Full Text Available Based on original interviews with key protagonists and documentary research, the article examines the way in which the DJs who worked at the Saint forged a white gay aesthetic across the first half of the 1980s. A private party located in the East Village, New York, the Saint attracted a privileged white male crowd, and this group's position within the emerging culture of neoliberalism, along with the deepening impact of the AIDS epidemic, encouraged its spinners to sever their ties with sounds that were associated with blackness. However, if Saint DJs rejected a high proportion of records that were being released by New York's independents, and also snubbed Chicago house when it broke in 1985, their forging of an aesthetic that emphasised seamless transitions, often between records that contained similar sonic qualities, preempted the style of mixing that would be popularised in house music culture.

  17. Die begrafnisdíens

    African Journals Online (AJOL)

    Num 20: 1; Jos 24: 30; Hand 5: 5 - 11). Selfs van die ... Gebruike rondom die begrafnis het van geslag tot geslag gewissel. De Vaux ... der geskied deur die hoorders 'te onderrig, te vermaan, te vertroos en te bestraf, soos dit in elke geval ..... gehandhaaf hoef te word, veral in die lig van die feit dat die predikant die kerklike.

  18. Die Ontstaan en Ontwikkeling van die Pan-Afrikanisme en due implikasies daarvan

    Directory of Open Access Journals (Sweden)

    A. J.H. van der Walt

    1961-03-01

    Full Text Available Dit was nie voor 1880 dat tropiese Afrika, dil is die grootste gedeelte van Wes-, Oos- en Midde-Afrika, deur ontdekkingsreisigers,handelaars en sendelinge tot so ’11 mate ontsluit is, dat dit in die vaarwater van die wêreldpolitiek geraak het nie. Lank voor hierdie tyd is natuurlik steunpunte aan die Wes-, Suid- en Ooskusdeur die Portugese en later die Nederlanders en Engelse eset ter wille van óf dieslawehandel en/óf as steunpunte op dielarig handelsweg na die ryke Ooste.

  19. Quality surveillance for steel forgings of SA508 Gr.3 used on the main NI equipment of AP1000 nuclear island

    International Nuclear Information System (INIS)

    Liu Lizhao

    2011-01-01

    Being a type of steel with ideal weldability, outstanding ability of anti-neutron irradiation embitterment and good property of fracture toughness and impact toughness, the steel of ASME SA508-3 was used widely for the nuclear island equipment of PWR Nuclear Power Plant. For the 3rd generation nuclear power plant AP1000, all large forgings and some critical components of the SG, RV and PRZ adopt this steel. Through analysis on the critical technical points during manufacturing of the SA508-3 forgings, this article try to identify the key points should be paid attention during the quality surveillance for this type of forgings, and to put forward the supervision method and focus during quality surveillance activities. (author)

  20. Die toepassing van die K3-model op die televisieteks Colour TV

    African Journals Online (AJOL)

    “OIL's approach to investigating the coloured market took place in the form of ethnographic research which ... communication strategies” (Botha 2010: 14). ... Op grond van die waarnemings, onderhoude en vraelyste het OIL tot die volgende ..... hold onto your nearest and dearest because this is going to be a kwaai mix bag.

  1. Characterization of a Viking Blade Fabricated by Traditional Forging Techniques

    Science.gov (United States)

    Vo, H.; Frazer, D.; Bailey, N.; Traylor, R.; Austin, J.; Pringle, J.; Bickel, J.; Connick, R.; Connick, W.; Hosemann, P.

    2016-12-01

    A team of students from the University of California, Berkeley, participated in a blade-smithing competition hosted by the Minerals, Metals, and Materials Society at the TMS 2015 144th annual meeting and exhibition. Motivated by ancient forging methods, the UC Berkeley team chose to fabricate our blade from historical smithing techniques utilizing naturally-occurring deposits of iron ore. This approach resulted in receiving the "Best Example of a Traditional Blade Process/Ore Smelting Technique" award for our blade named "Berkelium." First, iron-enriched sand was collected from local beaches. Magnetite (Fe3O4) was then extracted from the sand and smelted into individual high- and low-carbon steel ingots. Layers of high- and low-carbon steels were forge-welded together, predominantly by hand, to form a composite material. Optical microscopy, energy dispersive spectroscopy, and Vickers hardness mechanical testing were conducted at different stages throughout the blade-making process to evaluate the microstructure and hardness evolution during formation. It was found that the pre-heat-treated blade microstructure was composed of ferrite and pearlite, and contained many nonmetallic inclusions. A final heat treatment was performed, which caused the average hardness of the blade edge to increase by more than a factor of two, indicating a martensitic transformation.

  2. Vanaf die Fermat-punte na die De Villiers-punte van ’n driehoek

    Directory of Open Access Journals (Sweden)

    Michael de Villiers

    2010-01-01

    Full Text Available Hierdie artikel beskryf die ontdekking van die sogenaamde De Villiers-punte van ’n driehoek die bewyse wat betrokke is, en trek die historiese oorsprong terug na die Fermat-punte van ’n driehoek, die swaartepunt van ’n driehoek, en ’n nuttige veralgemening van die Fermat-punte van ’n driehoek.

  3. Cause and place of death in patients dying with colorectal cancer.

    Science.gov (United States)

    Jones, O M; John, S K P; Horseman, N; Lawrance, R J; Fozard, J B J

    2007-03-01

    Few studies on colorectal cancer look at the one-third of patients for whom treatment fails and who need a management strategy for death. This paper has examined the mode and place of death in patients with colorectal cancer. This study was a review of 209 deaths, analysed between January 2001 and September 2004 by retrospective review of a prospectively collected database. A total of 118 patients (group 1) had undergone resection of their primary colorectal cancer, 20 (group 2) had had a defunctioning stoma or bypass surgery and the remaining 71 patients (group 3) had either had no surgery, an open and close laparotomy or had a colonic stent. One hundred and fifty-six (75%) patients died of colorectal cancer with the remainder dying of other causes. The number of admissions to hospital and the number of days spent in hospital from diagnosis to death were greatest in group 1. Overall, only 34 patients (22%) dying from colorectal cancer died at home. Forty (26%) died in hospital and 70 (45%) died in a palliative care unit. Patients dying from colorectal cancer who undergo surgical resection of their primary tumour spend more time between diagnosis and death in hospital. They are also more likely to die in hospital than patients treated by surgical palliation or nonsurgically. Patients who are treated palliatively from the outset (group 3) are most likely to die at home. If hospital is accepted as an appropriate place for death from colorectal cancer, then greater provision for this should be made.

  4. Die uitbeelding van die vrou in Huisgenoot (1963 en 2013: ’n Multimodale diskoersanalise

    Directory of Open Access Journals (Sweden)

    Susann H. Marais

    2017-05-01

    Full Text Available Die standpunt dat die mens en die media in ’n verhouding van wedersydse beïnvloeding staan, sowel as die studie wat die kulturele konseptualisering van vroulikheid in twee Huisgenoot-uitgawes (1953 en 2003 ondersoek, geld as uitgangspunt vir dié studie. Hierdie studie het ten doel om te bepaal of daar ’n verskil is in die uitbeelding van die vrou in die Huisgenoot uitgawes van onderskeidelik 1963 en 2013. Volgens navorsing werk die visuele beeld en geskrewe teks saam om ’n boodskap oor te dra. Multimodale diskoersanalise (MDA word juis gebruik om beide visuele beeld en geskrewe teks te bestudeer. Sodoende word die metode van intersemiotiese komplementariteit binne MDA in hierdie studie gebruik. Die studie kom tot die gevolgtrekking dat die uitbeelding van die ideale vrou se verantwoordelikhede uitgebrei is, maar dat die vrou se rol tóg tot sekere ruimtes beperk word, soos die sigbaarheid van die moeder-stereotipe weerspieël.

  5. Die Dependenzgrammatik von Tesnière uno die neue slowenische Syntax

    Directory of Open Access Journals (Sweden)

    Breda Pogorelec

    1994-12-01

    Full Text Available In der Enzyklopädie der slowenischen Sprache (Toporišič 1992: 159 wird die Dependenzgrammatik unter besonderem Stichwort erklärt, in dem diese Grammatik zuerst als "eine Grammatik, die vor allem die Dependenzrelationen im Satz untersucht", definiert wird. Dann werden laut Lucien Tesnière im Satz Reza poje drei Elemente dargestellt: Reza, poje + die Verbindung dazwischen und dann werden drei Stufen des Graphs mit dem Verb als "dem Element, das die Ganzheit zusammenhält" erklärt; außerdem wird gesagt, daß die Koordination gemäß dieser Theorie durch die entsprechende Konjunktion ausgedrückt wird (aus dem graphischen Schema ist ersichtlich, daß dabei die Satzteilkoordination gemeint ist: pojeta -Tine -in -Tone. Im Kommentar wird hinzugefügt, daß auch "unsere" (= moderne slowenische Satzanalyse so aussieht, d. i. sie fängt mit dem Prädikat an, dann fragt man nach folgenden drei Hauptsatzteilen (Subjekt, Objekt, adverbiellen Prädikatbestimmungen, dann nach Attributen und deren Bestimmungen. Es wird die Methode des Unterstreichens von Satzteilen dargestellt, außerdem wird auf mehrere Arten der Dependenzgrammatik und auf verschiedene graphische Bezeichnungen der sprachlichen Erscheinungen aufgrund dieser Methode hingewiesen. -Im demselben Werk werden unter dem Stichwort translativ (Toporišič 1992: 331 zwei Bedeutungen gezeigt, von denen die erste auf einen entfernten Zusammenhang mit der Theorie von Tesnière hinweist, obwohl diese nicht erwähnt ist, lediglich bei der Definition selbst, nicht aber bei den Beispielen; translativ ist nach dieser Enzyklopädie "was aus einem Zustand in den anderen übertragen wird". Aber aus den Beispielen kann man sehen, das geht es um die Translation und nicht um Translativ als Instrument dieser Translation.

  6. Friction welding of a nickel free high nitrogen steel: influence of forge force on microstructure, mechanical properties and pitting corrosion resistance

    Directory of Open Access Journals (Sweden)

    Mrityunjoy Hazra

    2014-01-01

    Full Text Available In the present work, nickel free high nitrogen austenitic stainless steel specimens were joined by continuous drive friction welding process by varying the amount of forge (upsetting force and keeping other friction welding parameters such as friction force, burn-off, upset time and speed of rotation as constant at appropriate levels. The joint characterization studies include microstructural examination and evaluation of mechanical (micro-hardness, impact toughness and tensile and pitting corrosion behaviour. The integrity of the joint, as determined by the optical microscopy was very high and no crack and area of incomplete bonding were observed. Welds exhibited poor Charpy impact toughness than the parent material. Toughness for friction weld specimens decreased with increase in forge force. The tensile properties of all the welds were almost the same (irrespective of the value of the applied forge force and inferior to those of the parent material. The joints failed in the weld region for all the weld specimens. Weldments exhibited lower pitting corrosion resistance than the parent material and the corrosion resistance of the weld specimens was found to decrease with increase in forge force.

  7. Ruimtelike beplanning: die rol van die stads - en streeksbeplanner ...

    African Journals Online (AJOL)

    Ruimtelike beplanning: die rol van die stads - en streeksbeplanner in die saw. R Erasmus. Abstract. Since 1978 regional and town planners are employed in the SADF on a permanent basis as well as in the capacity of national service men. These men are all academically qualified and as such satisfy a need that developed ...

  8. Bevordering van transformerende leer: Die skryf van ’n reflektiewe joernaal in die Natuurwetenskappe

    Directory of Open Access Journals (Sweden)

    Erna R. du Toit

    2012-03-01

    Full Text Available Die doel van die artikel is om aan te toon hoe die skryf van ’n reflektiewe joernaal in die Natuurwetenskappe die perspektiewe en denke van onderwysstudente kan transformeer en/of leer kan bevorder. Die studie maak voorspraak vir die gebruik van ’n reflektiewe joernaal as ’n instrument vir studente om betekenis te gee aan die leeromgewing vanuit verskillende perspektiewe deur te leer in praktyk. ’n Kwalitatiewe navorsingsmetode is gevolg om die inskrywings in ’n joernaal te analiseer aan die hand van bepaalde indikatore. Die bevindinge toon dat die meeste studente na die praktykervaring positief was en sommiges het tot ander perspektiewe vanweë hul ervaring gekom.

  9. FLANDES, Flange Design for He Circuits by Taylor-Forge Method

    International Nuclear Information System (INIS)

    Pitchford, B.E.

    1977-01-01

    1 - Nature of the physical problem solved: Flange design for helium circuits. 2 - Method of solution: This is a flange design programme based on the Taylor forge method with an additional calculation of flange rotation and bolt load change during the application of internal pressure. The method relates only to the integral hub type of flange, with or without a secondary O-ring seal but will deal also with the flange and cover plate case

  10. Die impak van die verbond op 'n paradigma vir pastoraat: research ...

    African Journals Online (AJOL)

    Die verbond het 'n meer omvattende impak op pastorale sorg as ander paradigmas. Genoemde stelling word in hierdie artikel beredeneer. Daar word aangetoon dat die inhoud wat aan die gelowige gekommunikeer word, asook die tegnieke wat gebruik word, deur 'n verbondmatige paradigma vir pastorale sorg be?nvloed ...

  11. Die berekening van vloeiing in ’n roterende annulus deur die metode van kunsmatige saamdrukbaarheid

    Directory of Open Access Journals (Sweden)

    H. Grobler

    1987-03-01

    Full Text Available Die vloeiing van ’n onsaamdrukbare, viskeuse vloeier word ondersoek aan die hand van die numeriese oplossing van die gediskretiseerde Navier-Stokes- en kontinuiteitsbeheervergelykings. In die besonder word vloeiing in ’n annulus bestaande uit twee koaksiale silinders wat elk ten opsigte van die ander kan roteer, en met ’n voorgeskrewe drukval oor die lengte van die silinder, beskou. Die oplossings word bereken deur die toepassing van Chorin se metode van kunsmatige saamdrukbaarheid, waarin die tydonafhanklike beheervergelykings getransformeer word na tydafhanklike hulpvergelykings deur die invoering van ’n kunsmatige toestandsvergelyking. Die oplossing van die hulpvergelykings konvergeer na ’n stasionêre oplossing, wat ooreenstem met die oplossing van die oorspronklike tydonafhanklike beheervergelykings. Die gedrag van die vloeier, wanneer ten voile ontwikkelde laminêre vloeiing bereik word, is met sukses bereken. ’n Eenvoudige model vir die bepaling van ontwikkeling van vloeiing langs die annulus vir enige gegewe invloeisnelheidsprofiel word voorgestel. Die berekende resultate stem ooreen met die resultate wat uit die fisika van die probleem verwag word.

  12. ’n Voorgestelde matriks vir die pastorale berading van die verwonde geloofsvervreemde

    Directory of Open Access Journals (Sweden)

    Wentzel C. Coetzer

    2013-04-01

    Full Text Available Hierdie artikel fokus op die rol van pastorale berading aan die emosioneel-verwonde en geloofsvervreemde persoon deur middel van die redding in Christus. Die rol van God Drie-enig en die sentrale posisie van die Skrif word ondersoek. Verder word aspekte wat ’n Skrifgefundeerde mensbeeld onderlê, gekonstrueer. Die verband tussen emosionele trauma en geloofsvervreemding, asook die aspek van reg en geregtigheid, word hierna ondersoek. Die belangrikheid van die heil in Christus in die geestelike genesingsproses word ook bespreek. Ter afsluiting word ’n pastoraal-terapeutiese matriks voorgestel vir ingrype in die huidige lewenskrisis en die bestaande geloofsvervreemding met inagneming van die traumageskiedenis. Praktiese riglyne word verder verskaf as hulpmiddel vir begeleiding in die ondersteuningsproses. A proposed matrix regarding the pastoral counselling of the wounded faith-estranged. This article focuses on the role of the pastoral counselling of the emotionally wounded and faith-estranged person through the mediation of the salvation in Christ. The role of the Triune God and the central position of Scripture in mediating the salvation in Christ are also examined and the Scriptural view of man is constructed. The role of emotional trauma in the estrangement from God as well as the importance of justice and retribution are examined as it relates to the spiritual and emotional healing of the wounded faith-estranged. The article also discusses the prominence of the salvation in Christ in the spiritual healing process. In conclusion, a pastoral-therapeutic matrix of intervention is proposed to help in addressing the present life crisis and current faith-estrangement within the context of the trauma history, with a view to find healing from the woundedness and the faith-estrangement through salvation in Christ. Practical guidelines are offered to guide this supporting process.

  13. Etíese perspektiewe vir die bantering van konflik in die mediese ...

    African Journals Online (AJOL)

    mits versagtende omstandighede nie aangevoer kan word nie. Die howe oefen dan ook alleen sy regterlike funksie uit oor 'n konkrete geskil wat van daadwerklike belang vir die werklike partye is (Strauss 1982:14). Die hof laat hom lei deur die maatstaf van goeie sedes, die boni mores. Regter Mostert se verduideliking in ...

  14. 'n Verkenning van die soorte vennootskappe in die Amerikaanse reg ...

    African Journals Online (AJOL)

    In die Amerikaanse literatuur word talle verwysings gevind na die vennootskap in mynbou ("mining partnership"), familievennootskap ("family partnership", vennootskap in vaste eiendom ("partnership in real estate") en vennootskap vir boerdery ("farming partnership"). Hierdie onderskeiding is primer gebaseer op die tipe ...

  15. Die identifisering van maatstawwe vir die navorsingsprestasie van akademici

    Directory of Open Access Journals (Sweden)

    H. A. Labuschagne

    1990-06-01

    Full Text Available Identification of criteria for academic research performance. At South African universities, the achievement of objectives is usually measured in terms of so-called "process criteria" (e.g. pass rates, instead of performance criteria which reflect the quality of academic personnel. Stimulated by the need to identify valid indices of research performance, as a component of academic performance, this study investigated the dimensionality of several criteria, identified from empirical and literature studies. It was found that various valid criteria could be represented by six constructs, viz.: the stature of the researcher as scientist; scientific contributions; enhancement of own profession; community development; participation in research projects; and giving advice to persons or institutions outside the university. Opsomming By Suid-Afrikaanse universiteite word doelwitbereiking gewoonlik aan die hand van sogenaamde "prosesmaat-stawwe" (bv. slaagsyfers in plaas van prestasiemaatstawwe wat die gehalte van akademiese personeel weerspieel, gemeet. Na aanleiding van 'n behoefte aan die identifisering van geldige rigtingwysers vir navorsingsprestasie as 'n komponent van akademiese prestasie, is daar ondersoek ingestel na die dimensionaliteit van verskillende maatstawwe wat vooraf deur middel van empiriese- en literatuurstudies geidentifiseer is. Daar is gevind dat verskeie geldige maatstawwe deur ses konstrukte verteenwoordig word, te wete: die statuur van die navorser as wetenskaplike, wetenskaplike bydraes, uitbouing van eie professie, gemeenskapsontwikkeling, deelname aan navorsingsprojekte en advieslewering aan persone of instellings buite die Universiteit.

  16. Riglyne vir ‘n omvattende verrykingsprogram vir die bevordering van die geestesgesondheid

    Directory of Open Access Journals (Sweden)

    Antoinette Gmeiner

    1997-12-01

    Full Text Available In Suid-Afrika, met die snelle veranderinge in die politiek, ekonomie, lewenstyl en tegnologiese vooruitgang, gepaard met die geweld tans in die land, is die lewenskwaliteit van mense so bemvloed dat produktiwiteit en gedrag benadeel is. *Please note: This is a reduced version of the abstract. Please refer to PDF for full text.

  17. Die effek van intelligensie op die verhouding tussen lokus van kontrole en taakkompleksiteit

    Directory of Open Access Journals (Sweden)

    F. G. de Kock

    1995-06-01

    Full Text Available The effect of intelligence on the relationship between locus of control and task complexity. The aim of the study was to establish the effects of intelligence on the relationship between locus of control and task complexity. These constructs were selected by virtue of their importance in the literature, as well as the lack of empirical research regarding the assumed relationship which exists between them. The Human Sciences Research Council's (HSRC General Scholastic Aptitude Test (ASAT was used for measuring intelligence, Duttweiler's Internal Control Index (ICI was used for determining locus of control and the Raven's Advanced Progressive Matrices (APM was used as a criterion for coping with task complexity. These instruments were administered to 292 subjects to determine whether the relationship between locus of control and task complexity was effected when the effect of intelligence was controlled. The results indicated a significant relationship between locus of control and task complexity, however the relationship was no longer significant after the effect of intelligence was controlled. Opsomming Die doel van die studie was om die effek van intelligensie op die verhouding tussen lokus van kontrole en taak-kompleksiteit te ondersoek. Hierdie konstrukte is gekies na aanleiding van hulle belangrikheid in die literatuur asook die leemte in empiric se navorsing rakende die veronderstelde verband wat tussen hulle bestaan. Die Algemene Skolastiese Aanlegtoets (ASAT van die Raad vir Geesteswetenskaplike Navorsing (RGN is gebruik vir die meting van intelligensie, die Internal Control Index (ICI van Duttweiler is gebruik vir die meting van lokus van kontrole en die Advanced Progressive Matrices (APM van Raven is gebruik as maatstaf vir die bantering van taakkompleksiteit. Die genoemde meetinstrumente is op 292 proefpersone toegepas om te bepaal of die verband tussen lokus van kontrole en taakkompleksiteit geaffekteer word wanneer daar vir die effek

  18. eFORGE : A Tool for Identifying Cell Type-Specific Signal in Epigenomic Data

    NARCIS (Netherlands)

    Breeze, Charles E.; Paul, Dirk S.; van Dongen, Jenny; Butcher, Lee M.; Ambrose, John C.; Barrett, James E.; Lowe, Robert; Rakyan, Vardhman K.; Iotchkova, Valentina; Frontini, Mattia; Downes, Kate; Ouwehand, Willem H.; Laperle, Jonathan; Jacques, Pierre-ETienne; Bourque, Guillaume; Bergmann, Anke K.; Siebert, Reiner; Vellenga, Edo; Saeed, Sadia; Matarese, Filomena; Martens, Joost H. A.; Stunnenberg, Hendrik G.; Teschendorff, Andrew E.; Herrero, Javier; Birney, Ewan; Dunham, Ian; Beck, Stephan

    2016-01-01

    Epigenome-wide association studies (EWAS) provide an alternative approach for studying human disease through consideration of non-genetic variants such as altered DNA methylation. To advance the complex interpretation of EWAS, we developed eFORGE (http://eforge.cs.ucl.ac.uk/), a new stand-alone and

  19. Precipitation-hardening stainless steel bars, shapes, and forgings (ASME SA-564 with additional requirements)

    International Nuclear Information System (INIS)

    1975-05-01

    A standard prescribing requirements for precipitation-hardening stainless steel bars, shapes, and forgings (ASME SA-564 with additional requirements) for nuclear and associated applications is presented. This standard supersedes RDT M 7-6T, dated January 1974. (U.S.)

  20. Research on damage evolution and damage model of 316LN steel during forging

    Energy Technology Data Exchange (ETDEWEB)

    Duan, X.W., E-mail: dxwmike1998@sina.com; Liu, J.S.

    2013-12-20

    The tensile tests and unloading tensile experiments of 316LN steel were conducted. The damage evolution processes were investigated by optical microscope. The fracture was studied using a Scanning Electron Microscope (SEM) and optical microscope, of which, the chemical compositions were analyzed by Energy Dispersive Spectrometer (EDS). The results show that voids nucleate by decohesion of Al{sub 2}O{sub 3} inclusions–matrix interface and mainly along the grain boundary, especially, at triangular grain boundary junctions. The tensile processes were simulated by Deform2D under different deformation conditions. The critical damage values were obtained. The model between the critical damage value, temperature and strain rate was established by regression analysis. A combination of numerical simulation and upsetting experiments was applied for verifying the accuracy and reliability of critical damage value. These damage values can be used to predict the initiation of voids during 316LN steel hot forging. So, they have important instructional effects on designing forging technology of 316LN steel.

  1. 'n Ondersoek na die potensiaal-bepaling van werknemers in die landbousektor.

    Directory of Open Access Journals (Sweden)

    J. C. D. Augustyn

    1989-05-01

    Full Text Available An investigation into determining the potential of workers in the agricultural sector. Industrial Psychological principles and concepts are not being applied extensively in the agricultural sector. Against this background an attempt was made to scientifically identify potential and predict job performance amongst farm labourers. Using the PAQ method of job analysis, critical attributes were identified and a satisfactorily valid battery of tests was developed. The results of this study underlines the importance of the identification of the potential of farm labourers as a first step in the personnel management process. It also serves as a source of information that could be used by farmers for counselling purposes. Opsomming Wat die toepassing van Bedryfsielkundige beginsels en konsepte betref bestaan daar in die landboubedryf nog groot leemtes. Teen hierdie agtergrond is 'n poging aangewend om op 'n wetenskaplike wyse die potensiaal van plaasarbeiders te bepaal. Deur middel van die WOV-metode van posontleding is kritieke attribute by workers geidentifiseer en kon 'n toetsbattery met aanvaarbare geldigheid saamgestel word. Die resultate van die studie bevestig dat die identifisering van die potensiaal van plaaswerkers 'n noodsaaklike eerste stap in die personeelbestuursproses is. Dit kan ook met groot vrug as voorligtingshulpmiddel deur boere gebruik word.

  2. Die invloed van ‘n intensiewe opleidingsprogram op die Kardio Stres-indeks

    Directory of Open Access Journals (Sweden)

    Tammy Claassen

    2012-03-01

    Full Text Available Mense ondervind baie stressors in hul alledaagse lewe, wat ‘n groot uitwerking het op daagliksefunksionering. Kardio Stres-indeks (KSI is ‘n nie-indringende mate van die stres wat die hartervaar. KSI (uitgedruk as ‘n persentasie berekeninge word gebaseer op die duur van die QRSkompleks, hart tempo, ritme en standaardafwyking van die RR-interval (RRSD spesifieke parameters.

  3. Verskuiwing in die moraal?

    Directory of Open Access Journals (Sweden)

    S.P. van der Walt

    1974-03-01

    Full Text Available Modewoorde het ons deesdae oorgenoeg in die Christelike sedeleer en hulle kan nogal verwarring stig. U moet my vergun om met u te spreek oor een so ’n modewoord nl „verskuiwing’’ in die moraal. Dis nogal ’n mooi woord, wat so dikwels gebruik word op baie terreine en tog meer wil aandui as maar net ’n veranderde sienswyse, ’n wysiging in opvattinge of nuwe riglyne wat al gangbaar geword het in die praktyk. Die begrip wil eintlik die ewolusionêre gang beklemtoon, want dit is dan eintlik net die ou norme wat effens anders bekyk word of nie meer so nou geneem of dik onderstreep word nie. Die verskuiwing beteken dan dat alles nog dieselfde bly, net die posisie of plek het verander. Verskuiwing beteken tog plekverandering of plekwisseling en dan sekerlik nie in die sin dat die plekke ver uitmekaar lê nie. Verskuiwing beteken net maar vlak langs die vorige te staan kom. As dit dan ’n beter plek is, is dit ewolusie, ontwikkeling, verbetering.

  4. Die bantering van daar-interferensie in die Duits van Afrikaansmoedertaliges

    Directory of Open Access Journals (Sweden)

    Emerencia C. Steyn

    2013-02-01

    Full Text Available A comparison of sentence constructions in the soundtracks (simulcast of some television programmes indicates a general lack of a German equivalent for the multiple use of the A.frikaans daar. This naturally results in interference in the usage of German by A.frikaans speaking students, as they are inclined to construct their German sentences in accordance with the A.frikaans equivalents. This problem is mainly illustrated in either the erroneous use of a da or an inappropriate es gibt. Various exercises are submitted, aimed at obviating such errors of interference which are mainly noticeable in the spoken ·language. Soos blyk uit 'n vergelyking van segslryses in die parallelle klankbane van enkele televisieprogramme, het die veelvuldige gebruik van die Afrikaanse woord daar gewoonlik geen ekwivalensie in Duits nie. Dit lei maklik tot interferensie in die Duits van Afrikaansmoedertalige studente, omdat hulle daartoe neig om hul Duitse sinne soos die in A.frikaans te konstrueer. Hierdie probleem word hoofsaaklik in die foutiewe gebruik van da geopenbaar; soms egter ook in 'n misplaaste es gibt. Verskeie oefeninge word aan die hand gedoen om sulke interferensiefoute, wat vera! in m(mdelinge werk opduik, te bekamp.

  5. Die faktorstruktuur van Bass se veelfaktor- leierskapsvraelys in die Suid-Afrikaanse konteks

    Directory of Open Access Journals (Sweden)

    C .P. Ackermann

    2000-06-01

    Full Text Available The factor structure of Bass's Multifactor Leadership Questionnaire in the South African context. The aim of the study was to determine whether the factor structure of Bass's Multifactor Leadership Questionnaire (MLQ, as a measure of transformational leadership, could be replicated within the South African context. The MLQ was chosen not only because it promised to be a valid and reliable measuring instrument of the construct in question, but also due to the fact that there was an urgent need for such an instrument in the management of human resources within organisations undergoing transformation. The MLQ was administered to 406 subjects within the military context and was subjected to factor analysis and item analysis. The factor analysis yielded three factors, namely transformational leadership, transactional leadership and avoidance of leadership ("laissez faire" leadership. The reliabilities of the scales were determined by means of Cronbach's coefficient alpha, and yielded coefficients of 0,944, 0,736 and 0,803 respectively. The factor structure as conceptualised by Bass (1985 was largely confirmed in the present study. Opsomming Die doel van die studie was om vas te stel of die faktorstruktuur van die Veelfaktorleierskapsvraelys (MLQ van Bass, as maatstafvan transformasionele leierskap, in die Suid-Afrikaanse konteks gerepliseer kon word. Die MLQ is gekies omdat dit belofte inhou as n geldige en betroubare meetinstrument van die onderhawige konstruk, en ook weens die feit dat daar 'n dringende behoefte bestaan aan so n instrument vir gebruik in die bestuur van menslike hulpbronne in organisasies tydens verandering. Die MLQ is op 406 proefpersone binne militêre konteks toegepas, en aan n faktorontleding en n itemontleding onderwerp. Die faktorontleding het drie faktore opgelewer, te wete transformasionele leierskap, transaksionele leierskap en vermyding van leierskap ("laissez faire"-leierskap. Die betroubaarheid van die skale is bepaal

  6. Use of Gleeble MAXStrain unit for study of damage development in hot forging

    NARCIS (Netherlands)

    Geijselaers, Hubertus J.M.; Wang, Chao; Miroux, A.; Recina, V.; van den Boogaard, Antonius H.; Saanouni, K.

    2016-01-01

    The standard Gleeble MAXStrain unit has been modified to allow axial elongation. Analyses indicate that in this way both positive and negative hydrostatic stresses can be achieved during forging simulations, depending on the amount of strain per hit. This opens the way to the study of the effect of

  7. Ek wil hier graag van die geleentheid gebruik maak am die ...

    African Journals Online (AJOL)

    die wildlewe am van die jagters nie eers mel- ding te maak nie en in Lucas se werk kan hulle ure van genot deurbring. Wat ons veral in Lucas se publikasie interes- seer is sy deelname aan die agste grensoor~' log (1850-1853), sy aantekeninge in verband met die slag by Berea (20 Oesember 1852) en sy indrukke van ...

  8. Die radio in Afrika

    Directory of Open Access Journals (Sweden)

    S. de Villiers

    1966-03-01

    Full Text Available Omvang van radio-uitsendings in en na Afrika. — Redes vir die versnelde tempo van uitbreiding. — Radio as die geskikste massa-kommunikasiemiddel vir Afrika. — Faktore wat die verspreiding bemoeilik. — Skouspelagtige toename in luistertalle.Toe Plinius, wat in die jaar 79 oorlede is, in sy „Historia Naturalis” verklaar het dat daar altyd iets nuuts uit Afrika afkomstig is, kon hy nouliks voorsien het dat die „iets" negentien eeue later in die lug sou setel wat hierdie reuse-vasteland oorspan — ’n Babelse spraakverwarring en ’n ongekende, verbete woorde-oorlog in die etergolwe, onder meer daarop bereken om die harte en hoofde van derduisendes te verower.

  9. Halfkrone vir die Nagmaal

    African Journals Online (AJOL)

    Owner

    die omgewing van Velddrif en Laaiplek, ook noordwaarts verby Lambertsbaai tot by. Doringbaai en Strandfontein. “Haar seeverhale is Sussie (Kotze) se belangrikste bydrae tot die Afrikaanse letterkunde”, sê Kotzé-Myburgh in die voorwoord van die versamelbundel. Die leser word herinner aan Kotze se debuutroman, ...

  10. Die Leben Einsteins eine Reise durch die Geschichte der Physik

    CERN Document Server

    Fiami

    2005-01-01

    Jeder kennt die Namen Einstein, Newton oder Galilei. aber was weiss man über sie? Hier ein Porträt Einsteins anhand von sechs Meilensteinen aus der Geschichte der Physik. Einstein tritt auf als Protagonist in verschiedenen Epochen und bei verschiedenen Entdeckungen, die die Welt verändert haben.

  11. Die Ukraine-Krise und kritische Fragen an die EU-Erweiterungspolitik

    OpenAIRE

    Lippert, Barbara

    2014-01-01

    Die Ukraine-Krise konfrontiert die EU mit kritischen Fragen zu ihrer Erweiterungs-politik. Muss sie nach der Osterweiterung 2004/07 und dem gerade erst begonnenen Einzug der Westbalkan-Staaten nun mit Osteuropa für die übernächste Erweiterungs-runde rechnen? Sollte sie sich gar alsbald politisch verpflichten, interessierte und beitrittsfähige osteuropäische Länder eines Tages aufzunehmen? Wie jetzt auch viel-fach von EU-Akteuren geäußert, wäre dies voreilig: Denn in der konfliktgeladenen und ...

  12. Die waarde van voorafopleiding deur die ouer vir pedo-oudiometrie by drie- en vierjarige kleuters

    Directory of Open Access Journals (Sweden)

    Merisa Lodewyckx

    1981-11-01

    Full Text Available Die verkryging van akkurate, betroubare inligting aangaande die gehoorvermoë van jong kinders is van besondere belang vir die oudioloog, maar word dikwels bemoeilik aangesien die kleuter nie goeie samewerking bied in die vreemde pedo-oudiometriese situasie nie. Die oplossing hiervoor is grootliks geleë in die opleiding van die kind voor formele  gehoortoetsing en meer spesifiek  opleiding tuis deur die ouer. Die doel van hierdie studie was om 'n voorbereidende program op te stel wat die ouer tuis met die kind kan uitvoer, voordat formele  toetsing plaasvind. Die waarde en effek van hierdie program in die pedo-oudiometriese situasie is geevalueer by 'n groep drie- en vierjarige kleuters. Resultate dui daarop dat laer en meer akkurate drempels, 'n korter toetstydperk, verminderde angs en beter samewerking verkry is by die kleuters wat vooraf  opleiding ontvang het. Die opleidingsprogram kan dus in die kliniese praktyk benut word as voorafopleiding  vir pedo-oudiometrie.

  13. Stress corrosion of low alloy steel forgings

    International Nuclear Information System (INIS)

    Thornton, D.V.; Mould, P.B.; Patrick, E.C.

    1976-01-01

    The catastrophic failure of a steam turbine rotor disc at Hinkley Point 'A' Power station was shown to have been caused by the growth of a stress corrosion crack to critical dimensions. This failure has promoted great interest in the stress corrosion susceptibility of medium strength low alloy steel forgings in steam environments. Consequently, initiation and growth of stress corrosion cracks of typical disc steels have been investigated in steam and also in water at 95 0 C. Cracking has been shown to occur, predominantly in an intergranular manner, with growth rates of between 10 -9 and 10 -7 mm sec. -1 . It is observed that corrosion pitting and oxide penetration prior to the establishment of a stress corrosion crack in the plain samples. (author)

  14. Varswateralge en die ekonomie

    Directory of Open Access Journals (Sweden)

    W. E. Scott

    1988-03-01

    Full Text Available Die artikel bespreek die ekonomiese belong wat varswateralge alreeds het en hul moontlike verdere ontginning in die toekoms. Sowel gewenste as ongewenste aspekte word oorweeg en hoofsaaklik met voorbeelde uit Suid-Afrika geïllustreer. Die oormatige ontwikkeling van ongewenste alge in varswater verlaag die watergehalte dear verskeie chemiese veranderinge, wat kan wissel van smake en geure tot die produksie van verbindings wat gesondheidsgevare vir mens of dier inhou. Verwydering van ongewenste alge dra aansienlik by tot die koste van waterbehandeling. Oormatige alggroei belemmer ontspanningsgebruike en kan eiendomswaardes langs rivier- en damoewers beïnvloed.

  15. DIE GESKIEDENIS VAN AFDELING LOGISTIEK

    African Journals Online (AJOL)

    1 Aug 1978 ... dan ook aangebied, Agv die probleem wat ont- staan het met die gebrek aan goedgekeurde poste vir die Afdeling en as gevolg van die ver- wagte vertraging met die ondersoek van die. DOS-span, het die Afdeling Logistiek en Afde- ling Personeel oorleg gepleeg en laasgenoemde het ingestem dat die ...

  16. Die begrafnisdíens

    African Journals Online (AJOL)

    (De Vaux 1961:108). Was die begrafnis 'n familie of 'n kerklike aangeleentheid? Hierdie vraag word nie in die Bybel beantwoord nie. Abraham het sy vrou begrawe (Gen 23: 19-. 20). Isak en Ismael ..... ver gekom om die begrafnis 'n kerklike aangeleentheid te maak nie. Hierdie stap .... trou aan die sorg van God. * Die kerk ...

  17. het om die Woord van God aan die gemeente te bedien. A. D. P ont ...

    African Journals Online (AJOL)

    Test

    Sizoo vertel met die vlotheid van die ervare skrywer en die ver antwoordelikheid van die wetenskaplike ... Maar in stiptelike trou aan die feitelikheid, verlaat die skrywer hom uitsluitlik op die outentieke bronne om ... de leser; in sy rykdom van gegewens en wetenskaplike betroubaarheid kan dit met vrug gelees word deur die ...

  18. Magnetostriction of heavily deformed Fe–Co binary alloys prepared by forging and cold rolling

    International Nuclear Information System (INIS)

    Yamaura, Shin-ichi; Nakajima, Takashi; Satoh, Takenobu; Ebata, Takashi; Furuya, Yasubumi

    2015-01-01

    Highlights: • The as-forged Fe 25 Co 75 alloy shows the magnetostriction of 108 ppm. • The as-cold rolled Fe 25 Co 75 alloy shows the magnetostriction of 140 ppm. • Magnetostriction of Fe–Co alloy reached the maximum in a single bcc state. • Fcc phase is harmful to the increase in magnetostriction of Fe–Co alloy. • Fcc phase precipitation in Fe–Co alloy can be suppressed by cold rolling. - Abstract: Magnetostriction of Fe 1−x Co x (x = 50–90 at%) alloys prepared by forging and subsequent cold-rolling was studied as functions of alloy compositions and thermomechanical treatments. Magnetostriction of the as-forged Fe 25 Co 75 alloy was 108 ppm and that of the as-cold rolled Fe 25 Co 75 alloy measured parallel to the rolling direction (RD) was 128 ppm. The cold-rolled Fe 25 Co 75 alloy possessed a nearly {1 0 0}<0 1 1> texture, leading to the maximum magnetostriction of 140 ppm when measured at an angle of 45° to RD. Moreover, the fully annealed Fe 25 Co 75 and Fe 20 Co 80 alloys were gradually cold rolled and magnetostriction were measured. Results showed that the magnetostriction of those cold-rolled alloys drastically increased with increasing reduction rate. According to the XRD and TEM observations, intensity of the fcc peak gradually decreased with increasing reduction rate and that the alloys became to be in a bcc single state at a reduction rate higher than 90%, leading to a drastic increase in magnetostriction

  19. Design of the Driving and Clamp Rotation Hydraulic Control System for the Heavy Load Forging Manipulator

    Directory of Open Access Journals (Sweden)

    Li Geqiang

    2015-01-01

    Full Text Available The manipulator was equipped with full hydraulic drive. We designed the hydraulic systems for the driving and clamping rotation. We used a fuzzy PID control strategy to design the electro-hydraulic proportional control system. We built a united simulation model based on the co-simulation of MATLAB/Simulink and AMEsim. A mathematical model of the system was also established. We did separate simulations of the system’s dynamic characteristics for fast forging and normal forging working conditions. The parameters were optimized. The field test shows that the steady-state error of the hydraulic system is small and the system response is fast. The system’s rapid response speed, high precision, and stability under heavy load were realized.

  20. Forging Alliances in Interdisciplinary Rehabilitation Research (FAIRR): A Logic Model.

    Science.gov (United States)

    Gill, Simone V; Khetani, Mary A; Yinusa-Nyahkoon, Leanne; McManus, Beth; Gardiner, Paula M; Tickle-Degnen, Linda

    2017-07-01

    In a patient-centered care era, rehabilitation can benefit from researcher-clinician collaboration to effectively and efficiently produce the interdisciplinary science that is needed to improve patient-centered outcomes. The authors propose the use of the Forging Alliances in Interdisciplinary Rehabilitation Research (FAIRR) logic model to provide guidance to rehabilitation scientists and clinicians who are committed to growing their involvement in interdisciplinary rehabilitation research. We describe the importance and key characteristics of the FAIRR model for conducting interdisciplinary rehabilitation research.

  1. Professionalisme met verwysing na die posisie van bedryfsielkunde en die bedryfsielkundige in Suid-Afrika

    Directory of Open Access Journals (Sweden)

    A. van der Merwe

    1981-11-01

    Bedryfsielkunde, as relatief jong maar snelgroeiende wetenskap, word aan die hand van ses kriteria vir 'n professie evalueer. Resultate in hierdie verband dui in die algemeen daarop dat die vakgebied alreeds vir 'n aantal jare in 'n oorgangsfase tot ‘n volwaardige professie is en dat daar in hierdie proses reeds ver op die professionele kontinuum gevorder is. Verdere onder-soeke ten opsigte van professionele opleiding, die statutêre organisering van Bedryfsielkunde asook 'n professionele kode en vereniging vir die Bedryfsielkunde word bepleit ten einde die professionele posisie van die vakgebied volledig te konsolideer.

  2. Die design and process optimization of die cast V6 engine blocks

    Directory of Open Access Journals (Sweden)

    Henry Hu

    2005-02-01

    Full Text Available The use of aluminum, particularly for engine blocks, has grown considerably in the past ten years, and continues to rise in the automotive industry. In order to enhance the quality and engineering functionality of die cast engine blocks, die design and processes have to be optimized. In this study, a computer simulation software, MAGMAsoft, as an advanced tool for optimizing die design and casting process, was emplooyed to virtually visualize cavity filling and patterns of a V6 engine block. The original die design and process was simulated first to establish a baseline. A reality check was used to verify the predicted results. Then, the die modification with a different unner system was made by using a CAD software, Unigraphics (UG. The simulation on combinations of the modified die design and revised process was performed to examine the effect of die modification and process change on flow filling of V6 engine blocks. The simulated prediction indicateds that the enhancement of cavity filling due to the die and process modification minimizeds the occurrence of defects during casting, and consequently improves the quality of blocks. The results of mechanical testing show a significant increase in fatigue strengths, and a moderately improvement on tensile properties for the blocks die cast with the new die design and prpocess in comparison with those produced by the original ones.

  3. die ontstaan van vrouelugverenigings in suid-afrika voor die tweede

    African Journals Online (AJOL)

    aangestel. Ander eenhede het later gevolg. Drle van die Vrouehulplugmag se lelersflgure staan voor die VHLM se kleure wat gewy Is In Durban op 18 Mei 1940. Die vroue Is vlnr mal (meil E. Percival-Hart, It-kol (mev) D. Dunning en mal (mel) M. Egerton-Bird. 24. Scientia Militaria, South African Journal of Military Studies, ...

  4. ’n Oorsig van die bepaling van die vroeë bakterisidiese aktiwiteit van verskeie antituberkulosemiddels

    Directory of Open Access Journals (Sweden)

    P. R. Donald

    2003-06-01

    Full Text Available Die vroeë bakterisidiese aktiwiteit (VBA van ’n antituberkulosemiddel is die daaglikse afname van M tuberculosis in log10 kolonievormende eenhede per ml sputum, tydens die eerste twee dae van behandeling met die middel. Dit weerspieël die vermoë van ’n middel om aktief metaboliserende organismes in tuberkulose-longholtes te dood. Dit is ’n relatief goedkoop metode om in ’n klein groep pasiënte die antituberkulose-aktiwiteit van ’n middel, binne maande, in vivo te evalueer. Hierdie artikel som ons ondervinding op tydens sewe gepubliseerde VBA-studies, en die bronne van variasie in die prosedure word identifiseer. Die pasiënte in hierdie studies was gemiddeld 33 jaar oud, met ’n gemiddelde gewig van 50 kg en 55% het ekstensiewe of massiewe longaantasting gehad. Die hoogste VBA-waardes (0,50-0,66 is gevind in pasiënte wat isoniasied ontvang het, en die laagste waardes (0,05 en 0,09 respektiewelik was gevind in pasiënte wat die aminoglikosiede amikasien en paromomisien, albei in doserings van 15 mg/kg liggaamsgewig, ontvang het. Die algehele variasie in die VBA van 248 pasiënte was 0,0312, en die variasie toegeskryf aan die proses van sputumproduksie en -versameling was 0,0223. Dit blyk dat die verskillende aspekte van sputumproduksie en -versameling, betrokke by die lewering van ’n verteenwoordigende sputummonster, ’n groter bydrae maak tot variasie tydens die prosedure as die laboratoriumaspekte van die tegniek. Die keuring van pasiënte vir insluiting in VBA-studies, en hulle vermoë om saam te werk om ’n verteenwoordigende sputummonster te produseer, is van deurslaggewende belang in die suksesvolle voltooiing van VBA-studies.

  5. Riglyne vir die onderwys.

    Directory of Open Access Journals (Sweden)

    J. L. du Plooy

    1960-03-01

    Full Text Available In die afgelope vyftig jaar sedert die Unie tot stand gekom het, is veel op die gebied van onderwys tot stand gebring. Dit is heel natuurlik dat ’n mens sou vra: Wat van die toekoms?

  6. Die huwelik in die eerste-eeuse Mediterreense wêreld (III): Jesus en ...

    African Journals Online (AJOL)

    p1243322

    30 Jan 2007 ... description of what marriage, betrothal, adultery, divorce and ..... egbreuk teen wie? Wanneer daar in ag geneem word dat 'n man in die eerste- eeuse Mediterreense wêreld nie egbreuk teenoor sy vrou kon pleeg nie (kyk ... volg egbreuk teen die vrou in die huwelik beteken – al het die vrou owerspel.

  7. Die Energiesicherheit Europas in Bezug auf Erdgas und die Auswirkungen einer Kartellbildung im Gassektor

    OpenAIRE

    Krämer, Luis-Martín

    2011-01-01

    Die Dissertation untersucht die aktuelle Sicherheit der europaeischen Erdgasversorgung. Sie beruecksichtigt zudem die moeglichen Auswirkungen einer Kartellbildung auf die europaeische Gasversorgungssicherheit. Die Arbeit besteht aus einer detaillierten empirischen Studie und darauf aufbauender Szenarioanalyse. Hierzu wird auf den Interdependenzansatz von Robert O. Keohane und Joseph Nye zurueckgegriffen. Zur Darstellung des komplexen Themenbereichs wird auf die Darstellungspraxis der Dichten ...

  8. Der Einfluss von personeller Einkommensverteilung auf die „Great Depression“ und die „Great Recession“

    Directory of Open Access Journals (Sweden)

    Stefan Trappl

    2015-12-01

    Full Text Available Der Einfluss gestiegener Einkommensungleichheit auf die „Great Depression“ und die „Great Recession“ wurde mehrfach postuliert (Galbraith 1954/2009; Eccles 1951; Rajan 2010; Stiglitz 2012; Piketty 2014. Konkrete empirische Arbeiten zum Zusammenhang zwischen Einkommensverteilung und dem Entstehen von Wirtschaftskrisen gibt es aber bislang wenige. Kumhof/Ranciere (2010 überprüften die von Rajan (2010 aufgestellte Hypothese, die einen entsprechenden Zusammenhang postuliert, mittels Modellrechnung. Bordo/Meissner (2012 und darauf aufbauend Gu/Huang (2014 verwendeten unterschiedliche Regressionsmodelle in Bezug auf einen entsprechenden Zusammenhang, ohne jedoch eindeutige Ergebnisse zu liefern. Die vorliegende Arbeit schließt an diese Arbeiten an, beschränkt die Untersuchung allerdings auf Staaten, für die Daten für die letzten hundert Jahre verfügbar sind, und untersucht zudem explizit die Zeiträume um die beiden größten Krisen der letzten hundert Jahre, die „Great Depression“ und die „Great Recession“. Die Auswertungen zeigen, dass die personelle Einkommensverteilung ein guter Prädiktor für die Kriseneintrittswahrscheinlichkeit ist.

  9. Eksistensialisme in die Franse letterkunde

    Directory of Open Access Journals (Sweden)

    A. A. Teurlinckx

    1966-03-01

    Full Text Available Nooit sou die Franse jeug — en die van Europa en verder — in dié mate deur die eksistensialisme be'invloed gewees het nie, indien hierdie filosofie in wysgerige traktate sou begrawe gelê het. Die eksistensialiste het die koning van die filosofiese verhaal, Voltaire, met sukses op sy Candide- en Zadig-pad gevolg en hulle teorieë in letterkundige werke, ver- hale, romans en ook toneelstukke kwytgeraak, wat baie gelees is en waaruit ook ander literatore kragte en inspirasie geput het. Omrede daarvan is daar inderdaad baie eksistensialisme in die Franse letterkunde, maar ’n eintlike eksistensialistiese letterkunde was daar nie, en ’n Eksistensialistiese Letterkun­ dige skool het nooit bestaan nie. Ook sit hierdie eksistensialiste nie langs dieselfde vuur nie. Die Christelike eksistensialis Gabriel Marcel het op 21 April van hierdie jaar uitgevaar teen die „Sartriane” na aanleiding van die opvoering van Les Paravents, Die W indskerms van Jean Genêt in ’n Paryse staatsondersteunde teater. „Mens mag seker wees”, skryf Marcel in Les Nouvelles Littéraires, „dat die hele sartriaanse parogie sal skreeu: groot meesterwerk”. Voortgaande op sy distansiëring kan die literêre eksistensialiste in drie groepe ingedeel word: 1. Die Sartriane; 2. Die Christelike Eksistensialiste; 3. Die Onafhanklikes.

  10. Die singulation method

    Science.gov (United States)

    Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

    2013-06-11

    A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

  11. Die toekoms en ons roeping

    Directory of Open Access Journals (Sweden)

    S. du Toit

    1954-03-01

    Full Text Available Om te weet wat ons roeping in die toekoms sal wees, moet ons eers besef wat in ons eie tyd aan die gang is en langs watter lyne die dinge beweeg. Dit is ons plig om te let op die tekens van die tye in die lig van die profetiese Woord. En dan wil ons dadelik beklemtoon dat ons in Suid-Afrika nie in die waan moet lewe dat ons hier onbekommerd en onaangetas deur die wêreldgebeure ons roeping en bestemming kan uitwerk nie.

  12. Die rol van persoonlikheidstrekke in die weerstand teen stres

    Directory of Open Access Journals (Sweden)

    Sonja V. R. van Oudtshoorn

    1988-05-01

    Full Text Available The role of personality characteristics in resistance to stress: A study was conducted to establish whether certain personality characteristics contribute to resistance to stress. Rescue brigadesmen, performing dangerous rescue operations in the goldmining industry, served as basis for the study. The sample consisted of 63 current, 56 ex- and 50 non-brigadesmen. Results indicate that brigadesmen, on the basis of their personality structure, are better equipped to cope with stress. Scores on the 16PF show that they have a lower level of interpersonal anxiety (Factor Q4 and that they are more practical (Factor I, emotionally stable (Factor C, and conscientious (Factor G. These findings support existing knowledge of the 16PF. Opsomming Ten einde vas te stel ofdaar sekere persoonlikheidstrekke bestaan wat bydra tot weerstand teen stres, is 'n studie uitgevoer met reddingspanlede, wat lewensgevaarlike reddingsdiens in die goudmynbedryf verrig, as ondersoekgroep. Die streekproefhet uit 63 huidige, 56 oud-reddingspanlede en 50 amptenare, wat nog nooit aan die span behoort het nie, bestaan. Dit blyk dat reddingspanlede, op grond van hulle persoonlikheidstruktuur, beter toegerus is om stres te hanteer. Tellings op die 16PF toon dat hulle oor 'n laervlakvan interpersoonlike angs beskik, (Faktor Q4, dat hulle meer prakties (Faktor I, emosioneel stabiel (Faktor C en konsensieus is (Faktor G. Hierdie bevindinge sluit aan by die reeds bestaande kennis oor die 16PF.

  13. Manufacturing of ultra-large diameter 20 MnMoNi 5 5 steel forgings for reactor pressure vessels and their properties

    International Nuclear Information System (INIS)

    Onodera, S.; Kawaguchi, S.; Tsukada, H.; Moritani, H.; Suzuki, K.; Sato, I.

    1983-01-01

    A set of component material for PHWR RPV, including the largest forgings ever manufacture so far such as flanges (8,440 mm O.D.), shells and torus (7,960 mm O.D.) and dome (6,800 mm dia. in chord, 460 mm thick), was presented in the outline of manufacturing and properties. Even with increased dimensions and weight than the current largest forgings, the manufacture and the qualities achieved were satisfactory. These results encourage us in further developing PWRs and PHWRs with increased capacity. (orig.)

  14. Montessori-skole: die ander kant

    Directory of Open Access Journals (Sweden)

    Monica Viljoen

    1995-03-01

    Full Text Available Na aanleiding van die artikel “Die invloed van die New Age-beweging op die onderwysagenda van die toekoms” deur Lien van Niekerk en Corinne Meier van die Departement Historiese Opvoedkunde van Unisa (vgl. Koers, 59 (1 1994:69-84 wil ek graag ’n ander sy van Montessori-skole onder die aandag van Koers lesers bring.

  15. The Ties That Bind: How Social Capital Is Forged and Forfeited in Teacher Communities

    Science.gov (United States)

    Bridwell-Mitchell, E. N.; Cooc, North

    2016-01-01

    The effects of social capital on school improvement make it important to understand how teachers forge, maintain, or forfeit collegial relationships. Two common explanations focused on formal organizational features and individual characteristics do not address how social capital accrues from informal dynamics of teachers' interactions in…

  16. Tegnologie en die mens

    African Journals Online (AJOL)

    omgewingsbesoedeling, volgend op industrialisasie en verstedeliking, gee uit- ing tot krete van wanhoop en frustrasie. Die maatskaplike ontwrigting agv outomatisasie het die begrippe van vervreemding en naam- loosheid op die voorgrond van sosiale be- wustheid geplaas. • Die Neutrale Siening. Tegnologie was nag. 34.

  17. THE LEGAL PROTECTION FOR REAL LAND RIGHT HOLDER IN CASE OF FORGED RINCIK

    Directory of Open Access Journals (Sweden)

    Nirwana Nirwana

    2017-12-01

    Full Text Available The legal Protection For Real Land Right Holder in Case of Forged Rincik. The research aimed to investigate (1 the legal protection for the land owner whose possession was based on rincik evidence, and (2 the legal protection on the good-will buyer based on the forged rincik document used in the land sale transaction. This was the normative legal research, also called the library research or documentary study because the research was only conducted on the written regulations or other legal materials or secondary data consisting of the primary and secondary legal materials. The interview was performed to strengthen the theories and opinions in the research. The research also used the Secondary data. the data were analysed and presented using the qualitative descriptive method. The research result indicate that: (1 the real land owner with rincik possession issued after the year 1960 based on the decision of Indonesian Supreme Court No. 560K / PID / 2008 has not been fully protected due to the fact that the seller is funished for forging the rincik., returning the right to the land owner can not be carried out due to the decision of Indonesian Supreme Court Number. 482 / PK / Pdt / 2014 which make the buyer win, while the real land owner is the directed to sue the land seller to give the compensation: and (2 the legal protection on the good faith buyer based on forget rincik in the land sale transaction has been fully protected and has the ringt to possess the land based on the decision of Indonesian Supreme Court Number. 482/PK/Pdt/2014 because the buyer has bought the land in the presence of Temporary Land Title Registar.

  18. An Assessment of the Ductile Fracture Behavior of Hot Isostatically Pressed and Forged 304L Stainless Steel

    Science.gov (United States)

    Cooper, A. J.; Smith, R. J.; Sherry, A. H.

    2017-05-01

    Type 300 austenitic stainless steel manufactured by hot isostatic pressing (HIP) has recently been shown to exhibit subtly different fracture behavior from that of equivalent graded forged steel, whereby the oxygen remaining in the component after HIP manifests itself in the austenite matrix as nonmetallic oxide inclusions. These inclusions facilitate fracture by acting as nucleation sites for the initiation, growth, and coalescence of microvoids in the plastically deforming austenite matrix. Here, we perform analyses based on the Rice-Tracey (RT) void growth model, supported by instrumented Charpy and J-integral fracture toughness testing at ambient temperature, to characterize the degree of void growth ahead of both a V-notch and crack in 304L stainless steel. We show that the hot isostatically pressed (HIP'd) 304L steel exhibits a lower critical void growth at the onset of fracture than that observed in forged 304L steel, which ultimately results in HIP'd steel exhibiting lower fracture toughness at initiation and impact toughness. Although the reduction in toughness of HIP'd steel is not detrimental to its use, due to the steel's sufficiently high toughness, the study does indicate that HIP'd and forged 304L steel behave as subtly different materials at a microstructural level with respect to their fracture behavior.

  19. Modeling Cavitation in ICE Pistons Made with Isothermal Forging

    Directory of Open Access Journals (Sweden)

    V.V. Astanin

    2014-07-01

    Full Text Available Possible causes for cavitations in parts made with an Al-Si eutectic alloy AK12D (AlSi12 were explored with mathematical and physical modeling with involved acoustic emission. Pores were formed from micro-cracks, which appear during the early stages of a deformation process, with the help of micro-stresses appearing at phase boundaries (Al/Si interface due to thermal expansion. At the design stage of isothermal forgings of such products it is recommended to provide a scheme of the deformed shape, which is under uniform compression, to compensate for the inter-phase stresses.

  20. Automated ultrasonic shop inspection of reactor pressure vessel forgings

    International Nuclear Information System (INIS)

    Farley, J.M.; Dikstra, B.J.; Hanstock, D.J.; Pople, C.H.

    1986-01-01

    Automated ultrasonic shop inspection utilizing a computer-controlled system is being applied to each of the forgings for the reactor pressure vessel of the proposed Sizewell B PWR power station. Procedures which utilize a combination of high sensitivity shear wave pulse echo, 0 degrees and 70 degrees angled longitudinal waves, tandem and through-thickness arrays have been developed to provide comprehensive coverage and an overall reliability of inspection comparable to the best achieved in UKAEA defect detection trials and in PISC II. This paper describes the ultrasonic techniques, the automated system (its design, commissioning and testing), validation and the progress of the inspections