WorldWideScience

Sample records for clinoptilolite

  1. Characterization of modified clinoptilolite

    International Nuclear Information System (INIS)

    Novosad, J.; Jandl, J.; Woollins, J.D.

    1992-01-01

    Samples of clinoptilolite were modified using insoluble hexacyanoferrate from aqueous solution. The modified samples were characterized by elemental analysis, powder X-ray diffraction, solid state NMR and vibrational spectroscopy. The sorption properties of modified clinoptilolite were studied, too. Higher affinity for 137 Cs sorption in comparison with the natural clinoptilolite has been proved. (author) 5 refs.; 3 figs.; 2 tabs

  2. The removal of caesium ions using supported clinoptilolite

    International Nuclear Information System (INIS)

    De Haro-Del Rio, D.A.; Al-Joubori, S.; Kontogiannis, O.; Papadatos-Gigantes, D.; Ajayi, O.; Li, C.; Holmes, S.M.

    2015-01-01

    Highlights: • Natural clinoptilolite was supported over carbon structures produced from wastes. • Carbon–clinoptilolite showed an improved Cs + ions sorption capacity. • Overall kinetic rate was improved using carbon–clinoptilolite composite. • Diffusive resistances were modified using the composite and pure zeolite. • Final disposition volume can be reduced up to 60% by encapsulation. - Abstract: In this paper, the sorptive kinetic and diffusional characteristics of caesium ion removal from aqueous solution by carbon-supported clinoptilolite composites are presented. Natural clinoptilolite was supported on carbonaceous scaffolds prepared from date stones. Thermal treatment was applied to produce voids in the carbon which was conditioned using polydiallyldimethylammonium chloride to facilitate the clinoptilolite attachment. This method allowed the formation of a consistent zeolite layer on the carbon surface. The composite was applied in the removal of non-radioactive caesium ions showing an enhanced uptake from 55 mg g −1 to 120.9 mg g −1 when compared to clinoptilolite. Kinetic studies using Pseudo First Order model revealed an enhanced rate constant for carbon–clinoptilolite (0.0252 min −1 ) in comparison with clinoptilolite (0.0189 min −1 ). The Pseudo-First Order model described the process for carbon–clinoptilolite, meanwhile Pseudo Second Order model adjusted better for pure clinoptilolite. Diffusivity results suggested that mass transfer resistances involved in the Cs + sorption are film and intraparticle diffusion for natural clinoptilolite and intraparticle diffusion as the mechanism that controls the process for carbon–clinoptilolite composite. The most significant aspect being that the vitrified volume waste can be reduced by over 60% for encapsulation of the same quantity of caesium due to the enhanced uptake of zeolite

  3. Iodide adsorption on the surface of chemically pretreated clinoptilolite

    International Nuclear Information System (INIS)

    Chmielewska-Horvatova, E.; Lesny, J.

    1995-01-01

    The possibility to use the monoionic Ag +- form (eventually Hg +- and Hg 2+ -forms) of clinoptilolite of domestic origin for radioactive iodide elimination from waters has been studied. The capacity of the monoforms of clinoptilolite towards iodide exceeds many times that of the capacity of clinoptilolite in natural form. Due to the low solubility product of AgI, Hg 2 I 2 and HgI 2 iodides generate precipitates on the zeolite surface. Rtg analyses of the silver form of clinoptilolite after sorption of iodide demonstrate the formation of new crystals on the zeolite surface. The influence of interfering anions on the adsorption capacity of silver clinoptilolite towards iodide was investigated, too. Kinetic curves of iodide desorption from the surface of silver and mercury clinoptilolite were compared. Simultaneously, adsorption isotherms for the systems aqueous iodide solution/Ag-, Hg-clinoptilolite were determined. (author) 6 refs.; 7 figs.; 4 tabs

  4. THERMODYNAMICS OF ION-EXCHANGED NATURAL CLINOPTILOLITE

    Science.gov (United States)

    Natural clinoptilolite from Castle Creek, Idaho, and its cation-exchanged variants (Na-Cpt, NaK-Cpt, K-Cpt, and Ca-Cpt) were studied by high-temperature calorimetry. The hydration enthalpy for all clinoptilolites is about -30 kJ/mol H2O (liquid water reference state) at 25 C. T...

  5. The effects of clinoptilolite on piglet and heavy pig production

    Directory of Open Access Journals (Sweden)

    Archimede Mordenti

    2010-01-01

    Full Text Available To evaluate the effects of clinoptilolite on piglet and heavy pig production two separated trials have been performed. In the first trial 40 pigs of the initial body weight of 55 kg were used. Animals were homogeneously allocated to two groups: a control group traditionally fed and a clinoptilolite group in which feed contained the additive at 2%. Pigs were slaugh- tered at about 160 kg body weight. Blood samples were taken to determine blood urea nitrogen (BUN. In the second trial a total of 116 piglets from 12 litters was used. Six litters were fed from the 7th day of life a diet containing clinoptilolite at 2%. According to the dietary treatment of the suckling period, 84 weaned piglets were homogeneously allocated to two groups fed up to 33 kg body weight a diet containing or not clinoptilolite at 2%. In both trials daily weight gain, feed intake and pigs’ health were regularly recorded. The dietary inclusion of clinoptilolite at 2% did not resulted in any modification either of growing performances or of uraemia. Piglets on clinoptilolite diet showed a significant (P<0.05 improvement of faecal dry matter content. At slaughtering the dietary inclusion of clinoptilolite resulted in a trend towards an improvement of lean cuts yield and in a significant increase (P<0.05 of the ratio between lean and fat cuts. From our data it is sug- gested that clinoptilolite does not impair pig growing performances, determines a higher dry matter content of piglet fae- ces and improves carcass quality of heavy pigs with particular regard to lean cuts yield and lean to fat cuts ratio.

  6. Intracrystalline diffusion in clinoptilolite: Implications for radionuclide isolation

    International Nuclear Information System (INIS)

    Roberts, S.K.; Viani, B.E.; Phinney, D.

    1995-01-01

    Experiments have been performed to measure the rate of exchange diffusion in the zeolite clinoptilolite (CL) for elements important to radionuclide isolation at Yucca Mountain, NV. Clinoptilolite is one of the major sorptive minerals in the tuffs at Yucca Mountain, and occurs both as a major component in zeolitized units (Calico Hills), and in fractures in non-zeolitized tuffs (Topopah Spring). Field evidence and numerical modeling suggests that the movement of fluids through the tuff rocks adjacent to the potential repository may occur via episodic flow through fractures. Under conditions of rapid fracture flow the effective sorptive capacity of fracture-lining clinoptilolite may be controlled by exchange diffusion rather than exchange equilibrium

  7. Clinoptilolite compositions in diagenetically-altered tuffs at a potential nuclear waste repository, Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Broxton, D.E.

    1987-01-01

    The compositions of Yucca Mountain clinoptilolites and their host tuffs are highly variable. Clinoptilolites and heulandites in fractures near the repository and in a thin, altered zone at the top of the Topopah Spring basal vitrophyre have consistent calcium-rich compositions. Below this level, clinoptilolites in thick zones of diagenetic alteration on the east side of Yucca Mountain have calcic-potassic compositions and become more calcium rich with depth. Clinoptilolites in stratigraphically equivalent tuffs to the west have sodic-potassic compositions and become more sodic with depth. Clinoptilolite properties important for repository performance assessment include thermal expansion/contraction behavior, hydration/dehydration behavior, and ion-exchange properties. These properties can be significantly affected by clinoptilolite compositions. The compositional variations for clinoptilolites found by this study suggest that the properties will vary vertically and laterally at Yucca Mountain. Used in conjunction with experimental data, the clinoptilolite compositions presented here can be used to model the behavior of clinoptilolites in the repository environment and along transport pathways

  8. The effect of clinoptilolite on 137 Cs binding in broiler chickens

    Directory of Open Access Journals (Sweden)

    G. VITOROVIC

    2008-12-01

    Full Text Available The objective of this study was to evaluate the 137 Cs binding capacity of clinoptilolite.In the first in vitro experiment we investigated sorption of 137 Cs to natural and modified forms of clinoptilolite in highly acid solution,prepared to be similar to that of the gut of pigs (pH =2 3at 37 ºC.In the second in vivo experiment 137 Cs binding to a modified form of clinoptilolite was studied in orally contaminated broiler chickens.137 Cs sorption in the high acidity solution depended on clinoptilolite concentration and varied between 30 85 %of the initial activity.In the chickens,three hours after 137 Cs administration,there was 67%and 63%lower accumulation of 137 Cs in meat and edible organs (respectivelyand seven hours after 137 Cs administration,there was 69% and 49% lower accumulation of 137 Cs in meat and edible organs (respectivelycompared to the controls with no clinoptilolite added in food. Natural and modified forms of clinoptilolite have been shown to high sorption efficiency towards 137 Cs ions and could be recommended as possible radiocaesium binders in domestic animals.;

  9. Recovery of Nutrients from Biogas Digestate with Biochar and Clinoptilolite

    DEFF Research Database (Denmark)

    Kocatürk, Nazli Pelin

    in recovery of nutrients whose natural reserves are being depleted such as phosphorus and potassium. In this thesis I propose the use of sorbents i.e. biochar and clinoptilolite to concentrate nutrients and subsequently the application of digestate-enriched biochar and clinoptilolite as fertiliser. Therefore...... the overall objective of this thesis is to investigate the use of clinoptilolite and biochar to recover plant nutrients from the liquid fraction of digestate resulting from anaerobic digestion of animal manure and investigate the plant-availability of the recovered form of nutrients. In Chapter 1 (General...... of nutrients on sorbent) but decreasing efficiencies of clinoptilolite to remove nutrients from the liquid fraction of digestate. In Chapter 3, I studied the chemical activation of biochar by treating the biochar with deionised water, hydrogen peroxide, sulfuric acid and sodium hydroxide solutions...

  10. The effect of feeding clinoptilolite (zeolite) to laying hens

    African Journals Online (AJOL)

    The effect of feeding clinoptilolite (zeolite) to laying hens. M.D. Olver. Animal and Dairy Science Research Institute, lrene. One hundred and twenty 4-month-old, single-combed, brown. Hy-Line pullets were fed two isocaloric diets containing 16 or. 13,5o/o protein with and without 5% clinoptilolite in four.

  11. Physico-chemical characteristics and environmental exploitation of clinoptilolite Nizny Hrabovec

    International Nuclear Information System (INIS)

    Chmielewska, E.

    1999-01-01

    The clinoptilolite tuff used in this study, active mineral content of which was measured according to standardized techniques (e.g. X-ray diffraction, ion-exchange, water-vapor desorption) was 60% enriched. Physico-chemical characteristics considered from point of view as water treatment material and compared to siliceous sand and active coal as well as to some foreign clinoptilolite samples, e.g. mineralogical and chemical composition, thermic, alkali- and acid resistance, specific gravity, surface area, porosity, shipping weight, mechanical attrition and powdering survey, adsorption capacities of clinoptilolite towards Cs, Ba, Co, Fe, I, Ag, Zn and ammonium, hydration-dehydration behaviours and selectivity properties from among a major number of cations, have been investigated. Some pilot plant experiences of drinking water treatment with enhanced ammonium concentration on the field facility close to Bratislava and of tannery waste water treatment at Moravian plant using inland clinoptilolite will be presented. Mass-balance recycling loop for regeneration constituents recovery in tannery processing industry (ammonia and chromium) has been proposed and applied during pilot studies (capacity of installations ∼ 1 m 3 /hr). Iron and ammonium removal by addition of powdered clinoptilolite tuff in chemical coagulation processes for specific polluted surface water purification has been proven, respectively. Economic evaluation of ion-exchange technology by means of clinoptilolite with chemical regeneration and regeneration recovery by air-stripping method and of biological nitrification-denitrification for model hydraulic loading rate 6000 m 3 / day was calculated as well as the operating cost of both technologies were compared and will be documented. (author)

  12. Ammonia-nitrogen and phosphates sorption from simulated reclaimed waters by modified clinoptilolite

    International Nuclear Information System (INIS)

    Huo, Hanxin; Lin, Hai; Dong, Yingbo; Cheng, Huang; Wang, Han; Cao, Lixia

    2012-01-01

    Highlights: ► The salt and thermally modified clinoptilolite can effectively sorb NH 3 -N and phosphates. ► The phosphorus and nitrogen removal was consistent with Langmuir isotherm model. ► The modified clinoptilolite possesses rapid adsorption and slow balance characteristics. ► The adsorption is more in line with the Elovich adsorption dynamics equation. ► The entropy effect plays the role of the main driving force in the adsorption. - Abstract: This paper presents the investigation of the ammonia-nitrogen and phosphates sorption from simulated reclaimed wastewater by modified clinoptilolite. The results showed that the modified clinoptilolite has a high sorption efficiency and removal performance. The ammonia-nitrogen and phosphates removal rate of the modified clinoptilolite reached to 98.46% and 99.80%, respectively. The surface of modified clinoptilolite became loose and some pores appeared, which enlarged the specific surface area; the contents of Na and Fe increased, and the contents of Ca and Mg decreased. The modified clinoptilolite possesses rapid sorption and slow balance characteristics and ammonia-nitrogen and phosphates sorption is more consistent with the Langmuir isotherm model. The adsorption kinetics of ammonia-nitrogen and phosphates follows the Elovich adsorption dynamics equation, which describes the sorption of ammonia-nitrogen and phosphates in aqueous solution as mainly a chemical sorption. Results from the thermodynamics experiment involving ammonia-nitrogen and phosphates sorption reveal that the process is a spontaneous and endothermic process, and is mainly driven by entropy effect.

  13. Proton Resonance Lines of Water in Heulandite, Mordenite and Clinoptilolite

    International Nuclear Information System (INIS)

    Cruz Inclan, C.; Diaz Quintanilla, D.; Diaz Ruano, A.

    1986-01-01

    It is reported for the first time the proton magnetic resonance spectra of the clinoptilolite and mordenite between 220 K and 440 K. In mordenite it was observed that all water molecules have so an intensive diffusive movement, that they are completely delocalized. In clinoptilolite below 390 K, only a part of the water molecules are completely delocalized. Over 390 K all water molecules become delocalized. This particular behavior of the water molecules in clinoptilolite and mordenite is confronted with those structural models proposed by D.W. Breck. The concept of non-localized quantum state is introduced in order to explain the difference observed with the structural models. (author)

  14. Ion exchange and dehydration experimental studies of clinoptilolite: Implications to zeolite dating

    International Nuclear Information System (INIS)

    WoldeGabriel, G.

    1995-02-01

    Variable effects were noted on the argon (Ar) and potassium (K) contents of clinoptilolite fractions used in ion-exchange and dehydration experiments. The K contents of clinoptilolite fractions were differently affected during cation exchange with Ca-, Cs-, K-, and Na-chloride solutions. Ar was generally less affected during these experiments, except for a Na-clinoptitolite fraction exchanged for five days. Loss of Ar during organic heavy-liquid treatment and cleaning using acetone and deionized water does occur, as indicated by comparing the amounts of radiogenic Ar of treated and untreated fractions. Moreover, a regular decrease in radiogenic Ar contents was noted in clinoptilolite fractions during dehydration experiments at different temperatures for 16 hours. Comparable losses do not occur from saturated samples that were heated in 100 C for more than five months. Water appears to play a vital role in stabilizing the clinoptilolite framework structure and in the retention of Ar. The radiogenic Ar depletion pattern noted in clinoptilolite fractions dehydrated in unsaturated environment at different temperatures is similar to variations in the amount of radiogenic Ar observed in clinoptilolite samples from the unsaturated zone of an altered tuff. These results can be used to evaluate the extent of zeolitic water (and hence Ar) retention in unsaturated geologic settings. The utility of alkali zeolites (e.g., phillipsite, clinoptilolite, and mordenite) from low-temperature, open-hydrologic alteration as potential dateable minerals was evaluated using the K/Ar method as part of the Yucca Mountain Site Characterization Project, which is evaluating Yucca Mountain, Nevada, as a potential high-level radioactive waste repository site

  15. In vitro and in vivo efficiency of clinoptilolite in 137Cs binding

    International Nuclear Information System (INIS)

    Vitorovic, D.; Vitorovic, G.; Mladenovic, V.; Vukicevic, O.

    1998-01-01

    The results of investigation of the sorption of micro amounts of 137 Cs on powdered clinoptilolite in an electrolyte similar to the stomach content of animals are presented. The experiments were performed with the natural form of clinoptilolite from the Zlatopek mine (Vranjska Banja) and with the sodium form at 37 deg C. Simultaneously, investigation was made into the efficiency of the natural form of clinoptilolite in the radioprotection of chicks alimentary contaminated with 1 37 Cs. Clinoptilolite showed a high efficiency in 137 Cs sorption from the electrolyte solution, where 96-98% of initial activity was sorbed. Protection effect in chicks alimentary contaminated with 137 Cs, measured 3 and 7 hours after the contamination, was approximately 75% for the meat and edible inner organs of the chicks

  16. Clinoptilolite in Drinking Water Treatment for Ammonia Removal

    Directory of Open Access Journals (Sweden)

    H. M. Abd El-Hady

    2001-01-01

    Full Text Available In most countries today the removal of ammonium ions from drinking water has become almost a necessity. The natural zeolite clinoptiloliteis mined commercially in many parts of the world. It is a selective exchanger for the ammonium cation, and this has prompted its use in water treatment, wastewater treatment, swimming pools and fish farming. The work described in this paper provides dynamic data on cation exchange processes in clinoptilolite involving the NH4 +, Ca+2 and Mg+2 cations. We used material of natural origin – clinoptilolite from Nižný Hrabovec in Slovakia (particle-size 3–5 mm. The breakthrough capacity was determined by dynamic laboratory investigations, and we investigated the influence of thermal pretreatment of clinoptilolite and the concentration of regenerant solution (2, 5, and 10% NaCl. The concentrations of ammonium ion inputs in the tap water that we used were 10, 5, and 2 mg NH4 + l_1 and down to levels below 0.5 mg NH4 + l_1. The experimental results show that repeated pretreatment sufficiently improves the zeolite’s properties, and the structure of clinoptilolite remains unchanged during the loading and regeneration cycles. Ammonium removal capacities were increased by approximately 40 % and 20 % for heat-treated zeolite samples. There was no difference between the regenerates for 10% and 5% NaCl. We conclude that the use of zeolite is an attractive and promising method for ammonium removal.

  17. Ion exchange and dehydration effects on potassium and argon contents of clinoptilolite

    International Nuclear Information System (INIS)

    WoldeGabriel, G.; Levy, S.

    1995-01-01

    Zeolite-rich Miocene tuffs are an important part of the principal hydrochemical barrier to water-borne radionuclide transport from a potential high-level nuclear waste repository at Yucca Mountain, Nevada. The timing of zeolitization is an issue that relates to paleohydrology, permeability, zeolite stability, and unsaturated-zone geochemical processes. Exploratory K/Ar dating of clinoptilolite, the most abundant and widespread zeolite, shows a striking and consistent pattern of increasing apparent ages (2-13 Ma) with depth. Only the isotopic ages from the saturated zone are compatible with geologic evidence suggesting an age >10 Ma for most of the zeolites. Factors that may be responsible for the young apparent ages in the unsaturated zone were investigated. Cation exchange with recharge water and Ar diffusion under unsaturated conditions (processes that may be characteristic of the unsaturated zone) were evaluated experimentally for their effects on K/Ar systematics. Cation exchanging a natural clinoptilolite with Ca-, Cs-, K-, and Na- chloride solutions showed minimal effects on radiogenic Ar content. However, clinoptilolite heated at 200 degrees C for 16 hours in air lost a significant amount of its radiogenic Ar compared with minimal losses from clinoptilolite heated in water at 100 degrees C for over 5 months. The preliminary results indicate that Ar loss from incompletely hydrated clinoptilolite may be a major factor contributing to the young apparent ages of clinoptilolite in the unsaturated zone at Yucca Mountain

  18. Sorption of 60 Co in natural zeolite (clinoptilolite)

    International Nuclear Information System (INIS)

    Hernandez B, E.

    1996-01-01

    A Mexican zeolite (clinoptilolite) from Taxco, Guerrero, was partially stabilized with sodium cations. Radioactive Cobalt ( 60 Co) was used to study the Co 2+ sorption in the stabilized zeolite (Na + ). It was found that sorption in general does not favour the diffusion of cobalt between framework, it explains because of it is a natural zeolite and its composition heterogeneous decrease its exchange capacity by the generated competence to the existence other type of exchange ions. The cobalt retention reached the highest level, around 0.408 m eq Co 2+ /g in the Na-Clinoptilolite. The crystallinity of the aluminosilicates was maintained during experiments, it was verified by XRD patterns. (Author)

  19. Adsorption of Zinc Contained in the Poultry Feedstuff onto Clinoptilolite

    Directory of Open Access Journals (Sweden)

    E. Šucman

    2007-01-01

    Full Text Available The aim of this work was to find whether an adsorbent used as an additive in the feed mixtures could influence the concentration of free available zinc. The feed supplement ZeoFeed, which often constitutes a part of animal feed mixtures, mainly for poultry, was used as adsorbent in the amount of 10 g kg-1 of the feed mixture. A substantial part of ZeoFeed is clinoptilolite, a natural form of zeolite. Two sample preparation methods were used for the determination of zinc. The microwave-assisted wet digestion method was used to achieve a complete decomposition of the feed mixture in order to determine the total zinc concentration. The extraction method represented a simplified model of the processes in the digestive fluid tract. The extraction was done under laboratory temperature for 30, 60 and 120 min. Concentrations of zinc both in digests and extracts were determined by the method of the differential pulse anodic stripping voltammetry. The total zinc concentration (mean ± 95% confidence interval in the feed mixture without addition of clinoptilolite was found to be 145 ± 32.0 mg kg-1 and in the feed mixture with added clinoptilolite 146 ± 11.5 mg kg-1. The concentrations of free available zinc were approximately ten times lesser than the total amount. The analysis of extracts showed that no statistically significant differences between concentrations of zinc in extracts without clinoptilolite and with clinoptilolite addition have been found. The extraction time did not affect the extracted amount of zinc significantly. In addition to zinc, also other three trace elements, namely the essential trace element copper and the toxic trace elements cadmium and lead, were measured. However, these data have only preliminary value and need further verification.

  20. Metal adsorption capabilities of clinoptilolite and selected strains of bacteria from mine water

    Science.gov (United States)

    Mamba, B. B.; Dlamini, N. P.; Nyembe, D. W.; Mulaba-Bafubiandi, A. F.

    Small-scale mining has socio-economic advantages such as the reduction of unemployment and the general improvement of the economy. However, these operations if not properly managed or controlled have a potential to cause environmental damage, particularly with respect to the contamination of groundwater and water supplies that are not distant from where these mining activities take place. This paper focuses on metal removal from water contaminated by heavy metals emanating from small-scale mining operations using clinoptilolite and bacteria. Removal of As, Ni, Mn, Au, Co, Cu and Fe was carried out on mine water samples using original and HCl-activated (in 0.02 M and 0.04 M) natural clinoptilolite and bacterial strains (a mixed consortia of Bacillus strains ( Bacillus subtilis, Bacillus cereus, Bacillus firmus, Bacillus fusiformis, Bacillus macroides and Bacillus licheniformis), Pseudomonas spp., Shewanella spp. and a mixed consortia of Acidithiobcillus caldus, Leptospirillum spp., Ferroplasma spp. and Sulphobacillus spp.). The purpose of the study was to compare the removal efficiencies of the bacterial strains versus natural clinoptilolite adsorbents for metal cations. The Bacillus consortia removed most of the metals up to 98% metal removal efficiency with the exception of nickel where clinoptilolite showed good removal efficiency. The 0.02 M HCl-activated clinoptilolite also demonstrated excellent removal capabilities with Cu, Co and Fe removal efficiency of up to 98%. Both clinoptilolite and bacteria demonstrated capabilities of removing Cu 2+, Co 2+, Fe 2+, Mn 2+, As 3+ and Au from solution which augurs well for metal recovery from mining and mineral processing solutions, as well as in water decontamination.

  1. On the state of iron in a clinoptilolite

    International Nuclear Information System (INIS)

    Marco, J.F.; Gracia, M.; Gancedo, J.R.; Gonzalez-Carreno, T.; Arcoya, A.; Seoane, X.L.

    1995-01-01

    The characterization of an iron-containing natural zeolitic sample from the deposit of Tasajeras (Cuba) has been carried out by means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), X-ray photoelectron spectroscopy (XPS), 57 Fe Moessbauer spectroscopy and Fe K-edge X-ray absorption near-edge structure (XANES) and extended X-ray absorption fine structure (EXAFS). The results show that iron is mainly located (ca. 96%) as Fe 3+ in an octahedral site of the clinoptilolite framework. No evidence of tetrahedrally coordinated Fe 3+ was found. The remaining 4% Fe is located as Fe 2+ in an extraframework octahedral site, probably as a solvated ion, within the clinoptilolite structure. (orig.)

  2. Drying and purification of natural gas by clinoptilolite on an experimental pilot plant

    Energy Technology Data Exchange (ETDEWEB)

    Tsitsishvili, G V; Urotadze, S L; Lukin, V D; Bagirov, R M

    1976-02-01

    The paper deals with the process of the drying and purification of natural gas from CO/sub 2/ on an experimental pilot plant using the natural zeolite clinoptilolite. On the basis of the obtained data the dynamic activity of clinoptilolite against water and CO/sub 2/ has been calculated.

  3. Removal of uranium ions from synthetic wastewater using ZnO/Na-clinoptilolite nanocomposites

    International Nuclear Information System (INIS)

    Aghadavoud, Azadeh; Saraee, Khadijeh Rezaee Ebrahim; Shakur, Hamid Reza; Sayyari, Rasol

    2016-01-01

    Uranium is one of the heavy metals that is found in industrial wastewater and is very toxic for human and environment. In this work, natural clinoptilolite is used as a low-cost adsorbent for uranium removal from aqueous solutions. The sodium form of clinoptilolite and ZnO/Na-clinoptilolite nanocomposite were prepared. The sample sorption capacities for uranium removal from simulated drinking water in the presence of other anions and cations were investigated. Natural zeolite and its modified forms were characterized by XRD, XRF, FTIR, TEM and BET. Batch experiments were used to determine the best adsorption conditions. The effects of various parameters such as contact time, pH, initial uranium concentration, temperature and mass sorbent on the removal efficiency of uranium ions were studied. The equilibration was attained after 2 and 6 h for the Na-clinoptilolite and ZnO/Na-clinoptilolite nanocomposite, respectively. Both adsorbents showed relatively fast adsorption. Effective removal of uranium was demonstrated at pH values of 4-8 for both forms of zeolite. Temperature had no significant effect on adsorption. The maximum removal efficiency of uranium by the ZnO/Na-clinoptilolite nanocomposite in pH=7.2 and room temperature was 98.55%. Langmuir, Freundlich and Sips models were used for describing the equilibrium isotherms for uranium uptake. The Sips model corresponded well with the experimental data. The thermodynamic parameters, such as ΔG , ΔH and ΔS , have been calculated and interpreted. The pseudo-first order and pseudo-second order models were applied to describe the kinetic data. The pseudo-second order kinetic model had excellent kinetic data fitting (R2=1).

  4. Removal of uranium ions from synthetic wastewater using ZnO/Na-clinoptilolite nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Aghadavoud, Azadeh; Saraee, Khadijeh Rezaee Ebrahim; Shakur, Hamid Reza [Isfahan Univ. (Iran, Islamic Republic of). Dept. of Nuclear Engineering; Sayyari, Rasol

    2016-07-01

    Uranium is one of the heavy metals that is found in industrial wastewater and is very toxic for human and environment. In this work, natural clinoptilolite is used as a low-cost adsorbent for uranium removal from aqueous solutions. The sodium form of clinoptilolite and ZnO/Na-clinoptilolite nanocomposite were prepared. The sample sorption capacities for uranium removal from simulated drinking water in the presence of other anions and cations were investigated. Natural zeolite and its modified forms were characterized by XRD, XRF, FTIR, TEM and BET. Batch experiments were used to determine the best adsorption conditions. The effects of various parameters such as contact time, pH, initial uranium concentration, temperature and mass sorbent on the removal efficiency of uranium ions were studied. The equilibration was attained after 2 and 6 h for the Na-clinoptilolite and ZnO/Na-clinoptilolite nanocomposite, respectively. Both adsorbents showed relatively fast adsorption. Effective removal of uranium was demonstrated at pH values of 4-8 for both forms of zeolite. Temperature had no significant effect on adsorption. The maximum removal efficiency of uranium by the ZnO/Na-clinoptilolite nanocomposite in pH=7.2 and room temperature was 98.55%. Langmuir, Freundlich and Sips models were used for describing the equilibrium isotherms for uranium uptake. The Sips model corresponded well with the experimental data. The thermodynamic parameters, such as ΔG , ΔH and ΔS , have been calculated and interpreted. The pseudo-first order and pseudo-second order models were applied to describe the kinetic data. The pseudo-second order kinetic model had excellent kinetic data fitting (R2=1).

  5. Sorption of uranium by clinoptilolite modified by a some metals hydroxides

    International Nuclear Information System (INIS)

    Plotnikov, V.I.; Medvedeva, Z.V.; Zhabykbaev, G.T.

    2005-01-01

    In the present report the sorption character of uranium (IV) in the static conditions on the thin layer sorbents with application of the clinoptilolite of the Chankan deposit of the Republic of Kazakhstan is shown. A wide circle of metal hydroxides - in both the individual form and in the their mixture - is used. It is shown that the most sorptive capacity against the uranium (IV) has the modified clinoptilolite of MnO 2

  6. Serum Protein Electrophoretic Pattern in Neonatal Calves Treated with Clinoptilolite

    Directory of Open Access Journals (Sweden)

    Simona Marc

    2018-05-01

    Full Text Available The objective of our study was to determine the effects of clinoptilolite supplemented in colostrum on the blood serum protein electrophoretic pattern of new-born calves. Methods: Romanian Black and White new-born calves involved in the study were divided into 3 groups: the control group (C that received colostrum without clinoptilolite, and experimental groups I (E1 and II (E2 that received colostrum supplemented with 0.5% and 2% clinoptilolite, respectively. The concentration of total protein and protein fractions (albumin, α1-globulin, α2-globulin, β-globulin and γ-globulin were analyzed by electrophoresis on cellulose acetate. Results: At hour 30 after birth, concentrations of γ-globulins, β-globulin and total protein in E1 group of calves were higher than in control group by 42.11% (p < 0.05, 28.48% (p > 0.05 and 18.52% (p > 0.05, respectively, and were higher, but not significantly, in group E2 compared to the control group. This was in accordance with a significant lower albumin/globulin ratio in groups E1 and E2 (29.35%, p < 0.05 and 35.87%, p < 0.05, respectively than in control group at 30 h postpartum, which indicates an obvious increase of the globulins fraction in experimental groups. The conclusion: Clinoptilolite was effective in improving passive transfer in new-born calves, but it was more effective if added in colostrum with a dose of 0.5% than with a dose of 2%.

  7. Ozone decomposition on Ag/SiO2 and Ag/clinoptilolite catalysts at ambient temperature

    International Nuclear Information System (INIS)

    Nikolov, Penko; Genov, Krassimir; Konova, Petya; Milenova, Katya; Batakliev, Todor; Georgiev, Vladimir; Kumar, Narendra; Sarker, Dipak K.; Pishev, Dimitar; Rakovsky, Slavcho

    2010-01-01

    Silver modified zeolite (Bulgarian natural clinoptilolite) and Ag/silica catalysts were synthesized by ion exchange and incipient wet impregnation method respectively and characterized by different techniques. DC arc-AES was used for Ag detection. XRD spectra show that Ag is loaded over the surface of the SiO 2 sample and that after the ion-exchange process the HEU type structure of clinoptilolite is retained. UV-VIS (specific reflection at 310 nm) and IR (band at 695 cm -1 ) spectroscopy analysis proved that silver is loaded as a T-atom into zeolite channels as Ag + , instead of Na + , Ca 2+ , or K + ions, existing in the natural clinoptilolite form. The samples Ag/SiO 2 and Ag-clinoptilolite were tested as catalysts for decomposition of gas phase ozone. Very high catalytic activity (up to 99%) was observed and at the same time the catalysts remained active over time at room temperature.

  8. Modeling ion exchange in clinoptilolite using the EQ3/6 geochemical modeling code

    International Nuclear Information System (INIS)

    Viani, B.E.; Bruton, C.J.

    1992-06-01

    Assessing the suitability of Yucca Mtn., NV as a potential repository for high-level nuclear waste requires the means to simulate ion-exchange behavior of zeolites. Vanselow and Gapon convention cation-exchange models have been added to geochemical modeling codes EQ3NR/EQ6, allowing exchange to be modeled for up to three exchangers or a single exchanger with three independent sites. Solid-solution models that are numerically equivalent to the ion-exchange models were derived and also implemented in the code. The Gapon model is inconsistent with experimental adsorption isotherms of trace components in clinoptilolite. A one-site Vanselow model can describe adsorption of Cs or Sr on clinoptilolite, but a two-site Vanselow exchange model is necessary to describe K contents of natural clinoptilolites

  9. Immobilization of copper flotation waste using red mud and clinoptilolite.

    Science.gov (United States)

    Coruh, Semra

    2008-10-01

    The flash smelting process has been used in the copper industry for a number of years and has replaced most of the reverberatory applications, known as conventional copper smelting processes. Copper smelters produce large amounts of copper slag or copper flotation waste and the dumping of these quantities of copper slag causes economic, environmental and space problems. The aim of this study was to perform a laboratory investigation to assess the feasibility of immobilizing the heavy metals contained in copper flotation waste. For this purpose, samples of copper flotation waste were immobilized with relatively small proportions of red mud and large proportions of clinoptilolite. The results of laboratory leaching demonstrate that addition of red mud and clinoptilolite to the copper flotation waste drastically reduced the heavy metal content in the effluent and the red mud performed better than clinoptilolite. This study also compared the leaching behaviour of metals in copper flotation waste by short-time extraction tests such as the toxicity characteristic leaching procedure (TCLP), deionized water (DI) and field leach test (FLT). The results of leach tests showed that the results of the FLT and DI methods were close and generally lower than those of the TCLP methods.

  10. Ozone decomposition on Ag/SiO{sub 2} and Ag/clinoptilolite catalysts at ambient temperature

    Energy Technology Data Exchange (ETDEWEB)

    Nikolov, Penko, E-mail: penmail@mail.bg [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Genov, Krassimir; Konova, Petya [Institute of General and Inorganic Chemistry, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Milenova, Katya; Batakliev, Todor; Georgiev, Vladimir [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria); Kumar, Narendra [Laboratory of Industrial Chemistry, Process Chemistry Centre, Abo Akademi University, Biskopsgatan 8, 20500 Abo/Turku (Finland); Sarker, Dipak K. [School of Pharmacy and Biomolecular Sciences, University of Brighton, Lewes Road, Brighton BN2 4GJ (United Kingdom); Pishev, Dimitar [University of Chemical Technology and Metallurgy, 1756 Sofia (Bulgaria); Rakovsky, Slavcho [Institute of Catalysis, Bulgarian Academy of Sciences, 1113 Sofia (Bulgaria)

    2010-12-15

    Silver modified zeolite (Bulgarian natural clinoptilolite) and Ag/silica catalysts were synthesized by ion exchange and incipient wet impregnation method respectively and characterized by different techniques. DC arc-AES was used for Ag detection. XRD spectra show that Ag is loaded over the surface of the SiO{sub 2} sample and that after the ion-exchange process the HEU type structure of clinoptilolite is retained. UV-VIS (specific reflection at 310 nm) and IR (band at 695 cm{sup -1}) spectroscopy analysis proved that silver is loaded as a T-atom into zeolite channels as Ag{sup +}, instead of Na{sup +}, Ca{sup 2+}, or K{sup +} ions, existing in the natural clinoptilolite form. The samples Ag/SiO{sub 2} and Ag-clinoptilolite were tested as catalysts for decomposition of gas phase ozone. Very high catalytic activity (up to 99%) was observed and at the same time the catalysts remained active over time at room temperature.

  11. Evaluation of clinoptilolite for removal of ammoniacal nitrogen produced in aquaculture by Neutron activation analysis and UV-VIS spectrophotometry

    International Nuclear Information System (INIS)

    Bibiano C, L.; Iturbe G, J.L.; Lopez M, B.E.; Martinez M, V.

    1997-01-01

    In fish culture system, ammonia is excreted in the water as a metabolic by-product. In this work, sorption properties of clinoptilolite were determined and it was applied in culture of the rainbow trout Oncorhynchus mykiss for the removal of the ammoniacal nitrogen. The original clinoptilolite was treated with 1N NaCl solution from 24 to 192 h, for exchange NH 4 ions produced in fish culture. The content of Na in the clinoptilolite was determined by neutron activation analysis. The ammonium ion content in the exchange was analysed by UV-VIS spectrophotometry. Maximum uptake of sodium was reached between 24 and 48 hours at neutral pH with granules of the clinoptilolite from 14 to 24 mesh size. The adsorption capacity was from 3.28 to 6.8 mg of ammonium per gram of clinoptilolite. (Author)

  12. Methanol conversion to hydrocarbons using modified clinoptilolite catalysts. Investigation of catalyst lifetime and reactivation

    Energy Technology Data Exchange (ETDEWEB)

    Hutchings, G J; Themistocleous, T; Copperthwaite, R G

    1988-10-17

    A study of the deactivation and reactivation of modified clinoptilolite catalysts for methanol conversion to hydrocarbons is reported. Clinoptilolite catalysts, modified by either ammonium ion exchange or hydrochloric acid treatment, exhibit a short useful catalyst lifetime for this reaction (ca. 2-3 h) due to a high rate of coke deposition (3-5.10/sup -3/ g carbon/g catalyst/h). A comparative study of reactivation using oxygen, nitrous oxide and ozone/oxygen as oxidants indicated that nitrous oxide reactivation gives improved catalytic performance when compared to the activity and lifetime of the fresh catalyst. Both oxygen and ozone/oxygen were found to be ineffective for the reactivation of clinoptilolite. Initial studies of in situ on-line reactivation are also described. 3 figs., 15 refs., 4 tabs.

  13. Kinetics Modeling and Isotherms for Adsorption of Phosphate from Aqueous Solution by Modified Clinoptilolit

    Directory of Open Access Journals (Sweden)

    Mohammad Malakootian

    2012-01-01

    Full Text Available The Phosphorous discharge into the surface water led to excessive growth of algae and eutrophication in lakes and rivers. Therefore the phosphorus removal is important due to negative effect on water resources. The aim of this study was to investigat the modification of clinoptilolite and application of modified clinoptilolite for phosphorous adsorption from aqueous solution and isotherms and kinetics modeling. Hexadecyl Trimethyl Ammonium bromide (HDTMA-Br, Hexadecyl trimethyl Ammonium Chloride (HDTMA-Cl, Sodium Decyl Sulphate (SDS and Cetrimide-C were used for modification of clinoptilolite. Experiments were conducted using jar apparatus and batch system. The effect of pH, adsorbent doses, contact time, phosphate initial concentration and particle size were studied surveyed on phosphate adsorption by modified clinoptilolite. The most common isotherms and the kinetics adsorption equations were used for determination of adsorption rate and dynamic reaction. The results showed that maximum phosphate adsorption was obtained in the pH of 7 and contact time 90min. Also it was found with the increasing of phosphate initial concentration, phosphate removal efficiency decreased significantly. Langmuir No 2 showed a good correlation compared to other isotherms (R2=0.997. Maximum adsorption capacity was obtained in 20g/L adsorbent dose (22.73mg/g. Also Interaparticle diffusion kinetics well fits with experimental data (R2=0.999 with constant rate of 3.84mg/g min0.5. The result showed that modified clinoptilolite can be used successfully as low cost and effective absorbent for phosphate removal.

  14. Comparison the efficiency of AFCF and clinoptilolit obtained through single Cs 137 contamination of pheasants

    International Nuclear Information System (INIS)

    Vicentijevic, M.; Mitrovic, R.; Vitorovic, G.

    2009-01-01

    In practice are show effect of comparison efficiency AFCF and clinoptilolite obtained trough single 137 Cs contamination of pheasants. As experimental animals we used pheasants from the species pheasant colchicus. The total number of 2 months old pheasants, was 20. The pheasants were divided into 4 groups with 5 birds each. Every animal was simultaneously given water solution of 137 Cs (750 Bq) and radioprotector AFCF and clinoptilolite in water solution and mixed in pheasant food in the form of pellet. The level of contamination was determined by gamma - spectrometry in light meat, dark meat, liver and gizzard. The results show that the best protection effect was obtained by using AFCF than use radioprotector clinoptilolite. (author) [sr

  15. Removal of indigo blue using clinoptilolite-Fe

    International Nuclear Information System (INIS)

    Gutierrez S, E. E.; Colin C, A.; Solache R, M. J.

    2008-01-01

    The removal of indigo blue from aqueous solutions was evaluated using modified clinoptilolite with Fe (Z-Fe) which was characterized by SEM, EDS analysis and specific area (BET). The process followed the kinetics of pseudo-second order and Langmuir isotherm. Sorption capacity obtained was 18 mg g -1 and a solid-liquid ratio 10 g L -1 . (Author)

  16. Removal of ammonium ion from aqueous solution using natural Turkish clinoptilolite

    International Nuclear Information System (INIS)

    Karadag, Dogan; Koc, Yunus; Turan, Mustafa; Armagan, Bulent

    2006-01-01

    A study on ion exchange kinetics and equilibrium isotherms of ammonium ion on natural Turkish clinoptilolite (zeolite) was conducted using a batch experiment technique. The effects of relevant parameters, such as temperature, contact time and initial ammonium (NH 4 + ) concentration were examined, respectively. The pseudo first-order, pseudo second-order kinetic models and intraparticle diffusion model were used to describe the kinetic data. The pseudo second-order kinetic model provided excellent kinetic data fitting (R 2 > 0.990) and intraparticle diffusion effects ammonium uptake. The Langmuir and Freundlich models were applied to describe the equilibrium isotherms for ammonium uptake and the Langmuir model agrees very well with experimental data. Thermodynamic parameters such as change in free energy (ΔG 0 ), enthalpy (ΔH 0 ) and entropy (ΔS 0 ) were also determined. An examination of the thermodynamic parameters shows that the exchange of ammonium ion by clinoptilolite is a process occurring spontaneously and physical in nature at ambient conditions (25 deg. C). The process is also found to be exothermic. The results indicate that there is a significant potential for the natural Turkish clinoptilolite as an adsorbent material for ammonium removal from aqueous solutions

  17. Does the combination of biochar and clinoptilolite enhance nutrient recovery from the liquid fraction of biogas digestate?

    NARCIS (Netherlands)

    Kocatürk-Schumacher, Nazlı Pelin; Zwart, Kor; Bruun, Sander; Brussaard, Lijbert; Jensen, Lars Stoumann

    2017-01-01

    Concentrating nutrients on biochar and clinoptilolite and subsequently using the nutrient-enriched sorbents as a fertiliser could be an alternative way to manage nutrients in digestate. In this study, we investigated the use of biochar and clinoptilolite columns in removing ammonium, potassium,

  18. Investigation of the elution by seawater of caesium and strontium from loaded clinoptilolite

    International Nuclear Information System (INIS)

    Harder, B.R.; Mitchell, I.H.; Smyth, M.J.

    1985-07-01

    Simple investigations of the elution of caesium and strontium from loaded clinoptilolite are described. The clinoptilolite was loaded to levels expected in the British Nuclear Fuels plc SIXEP plant and contacted with seawater at approx. 15 C. (The elution time was measured until about 99% of the caesium and strontium had been eluted.) It was found that 99% of the caesium was eluted in 35 hours but the strontium (with more variable results) took at least 400 hours for 99% elution. (author)

  19. Does the combination of biochar and clinoptilolite enhance nutrient recovery from the liquid fraction of biogas digestate?

    DEFF Research Database (Denmark)

    Kocatürk, Nazli Pelin; Zwart, Kor; Bruun, Sander

    2017-01-01

    Concentrating nutrients on biochar and clinoptilolite and subsequently using the nutrient-enriched sorbents as a fertiliser could be an alternative way to manage nutrients in digestate. In this study, we investigated the use of biochar and clinoptilolite columns in removing ammonium, potassium......, orthophosphate and dissolved organic carbon (DOC) from the liquid fraction of digestate. Our objectives were to investigate the effect of the initial loading ratio between liquid and biochar on nutrient removal, and to investigate the effect of combining biochar with clinoptilolite on nutrient and DOC removal...... efficiency. Increasing the initial loading ratios increased nutrient concentrations on biochar to 8.61 mg NH4-N g(-1), 1.95 mg PO4-P g(-1) and 13.01 mg DOC g(-1), but resulted in decreasing removal efficiencies. The combination of biochar and clinoptilolite resulted in improved ammonium, potassium and DOC...

  20. Comparative study of cerium (IV) sorptive properties in zeolite Y and clinoptilolite

    International Nuclear Information System (INIS)

    Garcia D, O.C.

    1993-01-01

    Among the problems of protecting the environment from radioactive contamination, the reduction of radioactive releases by improving monitoring, decontamination, and burial methods is one of the most important. Natural sorbents are gaining increased significance for solving this problem. Among these, zeolites deserve special attention since they have sufficient sorptive capacity, are highly radiation resistant, are widely distributed exhibit selectivity and are inexpensive. In the present work we determine experimentally the sorptive characteristics of clinoptilolite as a function of various factors and demonstrate that clinoptilolite is capable of sorbing Ce(IV) over a wide pH range. (Author)

  1. Application of nonlinear regression analysis for ammonium exchange by natural (Bigadic) clinoptilolite

    International Nuclear Information System (INIS)

    Gunay, Ahmet

    2007-01-01

    The experimental data of ammonium exchange by natural Bigadic clinoptilolite was evaluated using nonlinear regression analysis. Three two-parameters isotherm models (Langmuir, Freundlich and Temkin) and three three-parameters isotherm models (Redlich-Peterson, Sips and Khan) were used to analyse the equilibrium data. Fitting of isotherm models was determined using values of standard normalization error procedure (SNE) and coefficient of determination (R 2 ). HYBRID error function provided lowest sum of normalized error and Khan model had better performance for modeling the equilibrium data. Thermodynamic investigation indicated that ammonium removal by clinoptilolite was favorable at lower temperatures and exothermic in nature

  2. The comparison of the structures of some cationic forms of clinoptilolite obtained from Manisa-Gordes in Turkey using their XRD spectrums

    International Nuclear Information System (INIS)

    Izci, E.; Orhun, O.

    2000-01-01

    In this study, at room temperature, XRD spectrums of Na, Ca, Li, Pb and natural forms of clinoptilolite, which is a natural zeolite obtained from Manisa-Gordes in Turkey, were taken and compared with each other according to their structures. Firstly, clinoptilolite samples, whose, diameters are smaller than 63 μm, were purified by HCl. Thus, impurities through the channels of clinoptilolite samples, were removed from their structures. Then, the samples washed several times by deionised water and filtered. So, HCl was removed from structures of these samples. Na, Ca, Li, Pb ionic forms of clinoptilolite were prepared by using batch method. XRD apparatus from Rigaku-Rint 2000 series. Comparing of XRD spectrums of these ionic and natural forms of clinoptilolite and finding the variations of their spectrums, what changes in their structures could be, were investigated. (authors)

  3. Effects of dietary clinoptilolite and calcium levels on the performance and egg quality of commercial layers

    Directory of Open Access Journals (Sweden)

    DA Berto

    2013-09-01

    Full Text Available Among the different feed additives studied in poultry production, clinoptilolite, an aluminosilicate capable of adsorbing harmful substances and of improving live performance and egg and meat quality, was evaluated. The objective of the present study was to evaluate the influence of dietary clinoptilolite and calcium levels on the performance and egg quality of layers. In total, 576 layers were distributed according to a completely randomized experimental design in a 3 x 4 factorial arrangement (three calcium levels - 2.5, 3.1, or 3.7% and four clinoptilolite levels - 0.0, 0.15, 0.25, or 0.50%, with 12 treatments of six replicates of eight birds each. The experiment included four 28-d cycles. The experimental diets were based on corn and soybean meal. Results were submitted to analysis of variance and means were compared by the test of Tukey at 5% significance level using SISVAR statistical package. There was a significant interaction between the evaluated factors for egg production and feed conversion ratio per dozen eggs and egg mass. The lowest calcium level resulted in worse performance and eggshell quality. Clinoptilolite levels affected albumen and yolk content. It was concluded that up to 0.50% inclusion of clinoptilolite in layer diets does not benefit layer performance or eggshell quality. Although the inclusion of only 2.5% calcium in layer diets is not recommended, it is possible to add 3.1% because it promoted similar results as the recommended level of 3.7%.

  4. Effects of Clinoptilolite on Copper Accumulation of Oreochromis niloticus

    Directory of Open Access Journals (Sweden)

    Nuray Çiftçi

    2018-05-01

    Full Text Available The copper accumulation in liver and gill tissues of Oreochromis niloticus, exposed to 2 ppm Cu and 1g/L clinoptilolite singly and to the same concentrations of their mixture over 24, 48, 72 and 96 hours was studied. ICP-AES spectrophotometer techniques were applied in determining tissue copper levels. Statistical evaluation of the experimental data was carried out by Student Newman Keul’s procedure. No mortality was observed during the experiments. Copper accumulation was lower in metal-clinoptilolite mixture group than metal singly group in gill tissue while no accumulation in both experimental groups in liver tissue (P<0.05. In addition, the copper level in the liver was lower in all experimental groups than in the control (P<0.05. Low Cu accumulation in gill tissue exposed in mixture groups can be explained by copper adsorption with chelating agent. The decrease of Cu reserves in the liver can be expressed by increase of copper-containing enzyme and protein synthesis.

  5. Preliminary assessment of clinoptilolite K/Ar results from Yucca Mountain, Nevada: A potential high-level radioactive waste repository site

    International Nuclear Information System (INIS)

    WoldeGabriel, G.; Bish, D.L.; Broxton, D.E.; Chipera, S.J.

    1992-01-01

    At Yucca Mountain, evidence for at least three distinct temporal groups of clinoptilolites can be delineated from the preliminary K/Ar dates (2--3 Ma; 4--5 Ma; 7--11 Ma). The older K/Ar dates that are similar to published illite/smectite ages (9--12 Ma) may be crystallization ages, whereas the younger dates probably represent continued diagenetic reactions of older clinoptilolites with percolating fluids. The K/Ar dates increase with depth, suggesting minimal argon loss in the deeper samples. Internal consistency of the clinoptilolite K/Ar results at different levels within the drill holes suggest that dating of K-rich zeolites may provide useful information for assessing the zeolitization at Yucca Mountain. Variations in the K/Ar dates are probably related to Ar loss during dissolution of older clinoptilolites and to contamination by finely crystalline feldspars

  6. Formaldehyde Adsorption into Clinoptilolite Zeolite Modified with the Addition of Rich Materials and Desorption Performance Using Microwave Heating

    Directory of Open Access Journals (Sweden)

    Amin Kalantarifard

    2016-01-01

    Full Text Available Granite, bentonite, and starch were mixed with clinoptilolite zeolite to produce a modified zeolite. The modified zeolite was tested for its ability to absorb formaldehyde from air. The modified sample formaldehyde adsorption capacity was then compared with those of commercially available clinoptilolite, faujasite (Y, mordenite, and zeolite type A. Studies were focused on the relationships between the physical characteristics of the selected zeolites (crystal structure, surface porosity, pore volume, pore size and their formaldehyde adsorption capacity. The removal of starch at high temperature (1100°C and addition of bentonite during modified clinoptilolite zeolite (M-CLZ preparation generated large pores and a higher pore distribution on the sample surface, which resulted in higher adsorption capacity. The formaldehyde adsorption capacities of M-CLZ, clinoptilolite, faujasite (Y, zeolite type A, and mordenite were determined to be 300.5, 194.5, 123.7, 106.7, and 70 mg per gram of zeolite, respectively. The M-CLZ, clinoptilolite, and faujasite (Y crystals contained both mesoporous and microporous structures, which resulted in greater adsorption, while the zeolite type A crystal showed a layered structure and lower surface porosity, which was less advantageous for formaldehyde adsorption. Furthermore, zeolite regeneration using microwave heating was investigated focusing on formaldehyde removal by desorption from the zeolite samples. XRD, XRF, N2 adsorption/desorption, and FE-SEM experiments were performed to characterize the surface structure and textural properties the zeolites selected in this study.

  7. Evaluation of natural zeolite clinoptilolite efficiency for the removal of ammonium and nitrate from aquatic solutions

    Directory of Open Access Journals (Sweden)

    Mozhdeh Murkani

    2015-01-01

    Full Text Available Background: Surface water and groundwater pollution with various forms of nitrogen such as ammonium and nitrate ions is one of the main environmental risks. The major objectives of this study were to evaluate the capacity of natural zeolite (clinoptilolite to remove NO3– and NH4+ from polluted water under both batch and column conditions. Methods: The laboratory batch and column experiments were conducted to investigate the feasibility of clinoptilolite as the adsorbent for removal of nitrate (NO3– and ammonium (NH4+ ions from aqueous solution. The effects of pH, clinoptilolite dosage, contact time, and initial metal ion concentration on NO3– and NH4+ removal were investigated in a batch system. Results: Equilibrium time for NO3– and NH4+ ions exchange was 60 minutes and the optimum adsorbent dosage for their removal was 1 and 2.5 g/L, respectively. The adsorption isotherm of reaction (r> 0.9 and optimum entered concentration of ammonium and nitrate (30 and 6.5 mg/L, respectively were in accordance with Freundlich isotherm model. The ammonium removal rate increased by 98% after increasing the contact time. Conclusion: Our findings confirmed that natural Clinoptilolite can be used as one of effective, suitable, and low-costing adsorbent for removing ammonium from polluted waters.

  8. K/AR dating of clinoptilolite, mordenite, and associated clays from Yucca Mountains, Nevada

    International Nuclear Information System (INIS)

    WoldeGabriel, G.

    1993-01-01

    Zeolites are abundant in the geologic record in both continental and marine environments. The purpose of the present study is to evaluate the utility of K-bearing zeolites for dating by the K/Ar method to determine the time of zeolite diagenesis at Yucca Mountain, Nevada (Fig. 1). At Yucca Mountain, K-rich clinoptilolite and possibly mordenite are the only potentially K/Ar dateable secondary minerals present in the zeolite-rich tuffs except for some illite/smectites (≥10% illite layers) associated with these minerals. Direct dating of K-rich clinoptilolite, the most abundant zeolite in the altered tuffs, is important to delineate zeolite chronology as part of the site characterization of Yucca Mountain

  9. In-field evaluation of clinoptilolite feeding efficacy on the reduction of milk aflatoxin M1 concentration in dairy cattle

    Directory of Open Access Journals (Sweden)

    Panagiotis D. Katsoulos

    2016-06-01

    Full Text Available Abstract Background Clinoptilolite is a natural zeolite with high adsorption capacity for polar mycotoxins such as aflatoxins. The efficacy of clinoptilolite in ameliorating the toxic effects of aflatoxicosis has been proven in monogastric animals, but there is no such evidence for ruminants. The aim of this study was to evaluate, under field conditions, whether the dietary administration of clinoptilolite in dairy cows could reduce the concentration of aflatoxin M1 (AFM1 in bulk-tank milk, in farms with higher than or close to 0.05 μg/kg of milk (European maximum allowed residual level. An objective of the present study was also to investigate the effect of particle size of clinoptilolite on aflatoxin binding. Methods Fifteen commercial Greek dairy herds with AFM1 concentrations in bulk tank milk ≥0.05 μg/kg were selected. Bulk tank milk AFM1 was determined prior to the onset and on day 7 of the experiment. Clinoptilolite was added in the total mixed rations of all farms at the rate of 200 g per animal per day, throughout this period. Two different particle sizes of clinoptilolite were used; less than 0.15 mm in 9 farms (LC group and less than 0.8 mm in 6 farms (HC group. Results Clinoptilolite administration significantly reduced AFM1 concentrations in milk in all farms tested at an average rate of 56.2 % (SD: 15.11. The mean milk AFM1 concentration recorded on Day 7 was significantly (P < 0.001 lower compared to that of Day 0 (0.036 ± 0.0061 vs. 0.078 ± 0.0074 μg/kg. In LC group farms the reduction of milk AFM1 concentration was significantly higher than HC group farms (0.046 ± 0.0074 vs. 0.036 ± 0.0061 μg/kg, P = 0.002. As indicated by the Pearson correlation, there was a significant and strong linear correlation among the milk AFM1 concentrations on Days 0 and 7 (R = 0.95, P < 0.001. Conclusions Dietary administration of clinoptilolite, especially of smallest particle size, at the rate of

  10. Effect of Clinoptilolite and Sepiolite Nanoclays on Human and Parasitic Highly Phagocytic Cells

    Directory of Open Access Journals (Sweden)

    Yanis Toledano-Magaña

    2015-01-01

    Full Text Available Nanoclays have potential applications in biomedicine raising the need to evaluate their toxicity in in vitro models as a first approach to its biocompatibility. In this study, in vitro toxicity of clinoptilolite and sepiolite nanoclays (NC was analyzed in highly phagocytic cultures of amoebas and human and mice macrophages. While amebic viability was significantly affected only by sepiolite NC at concentrations higher than 0.1 mg/mL, the effect on macrophage cultures was dependent on the origin of the cells. Macrophages derived from human peripheral blood monocytes were less affected in viability (25% decrease at 48 h, followed by the RAW 264.7 cell line (40%, and finally, macrophages derived from mice bone marrow monocytes (98%. Moreover, the cell line and mice macrophages die mainly by necrosis, whereas human macrophages exhibit increased apoptosis. Cytokine expression analysis in media of sepiolite NC treated cultures showed a proinflammatory profile (INFγ, IL-1α, IL-8, and IL-6, in contrast with clinoptilolite NC that induced lees cytokines with concomitant production of IL-10. The results show that sepiolite NC is more toxic to amoebas and macrophages than clinoptilolite NC, mostly in a time and dose-dependent manner. However, the effect of sepiolite NC was comparable with talc powder suggesting that both NC have low cytotoxicity in vitro.

  11. Effect of the Feed Additive Clinoptilolite (ZeoFeed on Nutrient Metabolism and Production Performance of Laying Hens

    Directory of Open Access Journals (Sweden)

    Miroslav Macháček

    2010-01-01

    Full Text Available The aim of this study was to assess the effects of two levels of clinoptilolite administered in feed (2% and 4% on some selected performance indicators, metabolic utilization of basic nutrients and the health status of laying hens. The selected 24 Bovans Goldline hybrid laying hens were divided into three equal groups, two experimental groups (E1 and E2 and one control group (C. The laying hens were housed individually in cages with an automatic supply of drinking water, manual feeding, in a setting with controlled light and temperature regimens. Hens from individual groups were all fed a complete feed mix of the same composition and the only difference was in clinoptilolite supplementation: feed mixes for E1 and E2 groups contained 2% and 4% of clinoptilolite (commercial additive ZeoFeed respectively, replacing the same amounts of wheat. The hens received feed mixes and drinking water ad libitum. During this 28-day experiment, feed consumption and the number and weight of eggs laid were monitored individually for each hen. At the end of the experiment, the balance test using the indicator method (Cr2O3 was performed in all eight hens in each of the groups. The results of balance tests were then used to calculate the metabolic utilization of selected nutrients (nitrogen, fat, ash, nitrogen-free extracts, starch, gross energy, Ca, P. After the balance tests, blood samples for haematological and biochemical examinations were collected via puncture of the vena basilica. The addition of 2% clinoptilolite to feed mix resulted in a highly significant (P ⪬ 0.01 increase in mean egg weight to 64.69 g, but the addition of 4% clinoptilolite in group E2 resulted in a highly significant (P ⪬ 0.01 decrease in mean egg weight to 62.20 g compared to the control (63.73 g. Moreover, daily feed mix consumption in group E1 decreased to 114 g per one laying hen/day compared to the controls (118 g per one laying hen/day. In group E2 (4% clinoptilolite, daily

  12. Determination of 60Co sorption in natural clinoptilolite

    International Nuclear Information System (INIS)

    Hernandez B, E.; Granados C, F.

    1997-01-01

    It was studied the clinoptilolite behavior coming from a deposit in Taxco, Guerrero in hydration and stabilization conditions with sodium for determining its sorption properties. The ion exchange process was carried out through gamma spectrometry using a CoCl 2 solution marked with 60 Co at p H 6.5 in different contact times. It was observed a maximum sorption of 0.408 m eq Co +2 /g mineral, from 0.314 m eq Co +2 /g mineral correspond at ion exchange. (Author)

  13. The influence of pH on the adsorption of lead by Na-clinoptilolite ...

    African Journals Online (AJOL)

    2011-09-28

    Sep 28, 2011 ... Adsorption of heavy metals by clinoptilolite, the most used natural zeolite found in ... dehydrated ionic radius and the electric charge of ions. So, the ... ionic radii have high dehydration energy, thus affecting Step. (iv). Generally ...

  14. Clinoptilolite zeolite influence on nitrogen in a manure-amended sandy agricultural soil

    Science.gov (United States)

    Development of best management practices can help improve inorganic nitrogen (N) availability to plants and reduce nitrate-nitrogen (NO3-N) leaching in soils. This study was conducted to determine the influence of the zeolite mineral clinoptilolite (CL) additions on NO3-N and ammonium-nitrogen (NH4-...

  15. The effect of exchangeable cations in clinoptilolite and montmorillonite on the adsorption of aflatoxin B1

    Directory of Open Access Journals (Sweden)

    DRAGAN STOJSIC

    2001-08-01

    Full Text Available The adsorption of aflatoxin B1 (AFB1 by cation-exchanged clinoptilolite zeolitic tuff and montmorillonite was investigated at 37°C and pH 3.8 from an aqueous electrolyte having a composition similar to that of gastric juices of animals. Both minerals were exchanged from the natural form to the sodium form and then to the Cu2+, Zn2+ and Co2+-rich forms. The cation exchange was different for the different cations, but in all cases the exchanges were larger on montmorillonite than on clinoptilolite. The degree of exchange on montmorillonite was 76 % for copper (from a total of CEC 0.95 meq/g, Cu2+ –0.73 meq/g and 85 % for zinc and cobalt. Under the same conditions (concentration, temperature, pH, contact time, the degree of exchange on zeolitic tuff was 12 % for Cu2+ (from a total CEC of 1.46 meq/g, Cu2+ –0.17 meq/g, 8 % for Zn2+ and 10 % for Co2+. Both groups of mineral adsorbents showed high AFB1 chemisorption indexes (ca. For the montmorillonite forms, ca ranged from 0.75 for the Cu-exchanged montmorillonite to 0.89 for the natural Ca-form, 0.90 for the Zn-exchanged form and 0.93 for the Co-exchanged montmorillonite. The adsorption of AFB1 on the different exchanged forms of clinoptilolite gave similar values of ca for the Cu and Ca forms (0.90 and values of 0.94 and 0.95 for the Zn- and Co-exchanged form. The impact of the mineral adsorbents on the reduction of essential nutrients present in animal feed (Cu, Zn, Mn and Co showed that the Ca-rich montmorillonite had a higher capability for the reduction of the microelements than the Ca-rich clinoptilolite.

  16. AFCF and clinoptilolite use in reduction of (137)Cs deposition in several days' contaminated broiler chicks.

    Science.gov (United States)

    Mitrovic, B; Vitorovic, G; Vitorovic, D; Dakovic, A; Stojanovic, M

    2007-01-01

    The objective of this study was to investigate the binding efficiency of AFCF and clinoptilolite, mixed to the feed and administered orally using gastric tube to chronically (137)Cs alimentary contaminated broiler chicks. Seventy-five male Hybro broiler chicks, between 35 and 47 days of age were divided into five groups (15 birds per group) reared in cages (five birds in a cage) and fed a standard diet. Every day during 13 days of the experimental period all chicks received orally 1 ml CsCl water solution with activity of 1310 Bq ml(-1)(137)Cs (gastric tube). Group 1 was the control group and received no binders. The experimental groups received the binders. Group 2 received 0.2 g of AFCF in the form of water solution (gastric tube); group 3 received 0.2% AFCF in the feed; group 4 received 2g clinoptilolite in the form of water suspension (gastric tube) and group 5 received 2% clinoptilolite in the feed. Five chicks from each group were sacrificed on days 4, 10 and 13 of the experimental period. Using gamma spectrometric methods specific activity of (137)Cs was determined in the samples of breast meat, liver and gizzard. The results obtained showed that administering binders to the chronically contaminated broiler chicks significantly (pmeat, liver and gizzard. Decreasing deposition of (137)Cs in breast meat and internal organs increased with time of contamination and binders' administration. With AFCF as a cesium binder, on day 13 of measuring the (137)Cs activity in breast meat was 80-83% lower than that in the control group, 89% in liver and 83-84% in gizzard. Natural clinoptilolite demonstrated lower binding efficiency. On day 13 of measuring the (137)Cs activity in breast meat was 53-69% lower than that in the control group, 67-60% in liver and 59-71% in gizzard.

  17. Compost maturity and nitrogen availability by co-composting of paddy husk and chicken manure amended with clinoptilolite zeolite.

    Science.gov (United States)

    Latifah, Omar; Ahmed, Osumanu Haruna; Susilawati, Kassim; Majid, Nik Muhamad

    2015-04-01

    The availability of paddy husk from rice processing plants remains high owing to increase in the worldwide rice consumption. Increasing demand for chicken products leads to poultry wastes production. Co-composting of the aforementioned wastes could solve the indiscriminate disposal of these wastes. Thus, co-composting of paddy husk and chicken slurry with clinoptilolite zeolite and urea as additive was carried out. Clinoptilolite zeolite was used to enhance ammonium and nitrate retention in the compost. Temperature of the compost was monitored three times daily for 55 days. Cation exchange capacity, organic matter, ash, humic acids, pH, total C, N, C/N ratio; total P, exchangeable Ca, Mg, K, NH4+, NO3-, and heavy metals contents were determined using standard procedures. pH, total N, humic acids, ash, NH4+, NO3-, P, Ca, Mg, and K contents increased but the salinity, heavy metals contents, and microbial population were low after the co-composting process. Zea mays L. (test crop) seed germination rate in distilled water and the compost were not significantly different. Growth of Spinach oleracea (test crop) on a peat-based growing medium and the compost was also not significantly different. These findings were possible because the clinoptilolite zeolite used in co-composting reduced accumulation of heavy metals that may have damage effects on the test crops. Mature compost with good agronomic properties can be produced by co-composting chicken slurry and paddy husk using clinoptilolite zeolite and urea as additives. © The Author(s) 2015.

  18. Removal of Cu 2+ Ions from Aqueous Medium Using Clinoptilolite/Emeraldine Base Composite

    Directory of Open Access Journals (Sweden)

    Silviya I. Lavrova

    2016-12-01

    Full Text Available The aim of this study was to investigate the removal efficiency of in situ synthesized composites consisted of emeraldine base and clinoptilolite on copper ions removal from aqueous medium. Two composite materials (Composite I and Composite II with different quantity of clinoptilolite were synthesised. The influence of the composite dosage, the contact time and the initial copper ions concentration has been studied. The results show that the significant removal of the copper ions becomes at the first minute of the contact between the composite material and the aqueous medium and the longer contact time leads to increasing of the copper ions removal. The removal efficiency at the 1st minute was 57.5% and 77.3% using Composite Iand Composite II, respectively. Maximum removal efficiency of 87.3% and 96.8% was achieved at the same dosage of Composite I and Composite II, respectively, at contact time of 360 minutes and temperature of 24 °C.

  19. Clinoptilolite zeolite influence on inorganic nitrogen in silt loam and sandy agricultural soils

    Science.gov (United States)

    Development of best management practices can help improve inorganic nitrogen (N) availability to plants and reduce nitrate-nitrogen (NO3-N) leaching in soils. This study was conducted to determine the influence of the zeolite mineral Clinoptilolite (CL) additions on NO3-N and ammonium-nitrogen (NH4...

  20. AFCF and clinoptilolite use in reduction of 137Cs deposition in several days' contaminated broiler chicks

    International Nuclear Information System (INIS)

    Mitrovic, B.; Vitorovic, G.; Vitorovic, D.; Dakovic, A.; Stojanovic, M.

    2007-01-01

    The objective of this study was to investigate the binding efficiency of AFCF and clinoptilolite, mixed to the feed and administered orally using gastric tube to chronically 137 Cs alimentary contaminated broiler chicks. Seventy-five male Hybro broiler chicks, between 35 and 47 days of age were divided into five groups (15 birds per group) reared in cages (five birds in a cage) and fed a standard diet. Every day during 13 days of the experimental period all chicks received orally 1 ml CsCl water solution with activity of 1310 Bq ml -1 137 Cs (gastric tube). Group 1 was the control group and received no binders. The experimental groups received the binders. Group 2 received 0.2 g of AFCF in the form of water solution (gastric tube); group 3 received 0.2% AFCF in the feed; group 4 received 2 g clinoptilolite in the form of water suspension (gastric tube) and group 5 received 2% clinoptilolite in the feed. Five chicks from each group were sacrificed on days 4, 10 and 13 of the experimental period. Using gamma spectrometric methods specific activity of 137 Cs was determined in the samples of breast meat, liver and gizzard. The results obtained showed that administering binders to the chronically contaminated broiler chicks significantly (p 137 Cs transfer and deposition in breast meat, liver and gizzard. Decreasing deposition of 137 Cs in breast meat and internal organs increased with time of contamination and binders' administration. With AFCF as a cesium binder, on day 13 of measuring the 137 Cs activity in breast meat was 80-83% lower than that in the control group, 89% in liver and 83-84% in gizzard. Natural clinoptilolite demonstrated lower binding efficiency. On day 13 of measuring the 137 Cs activity in breast meat was 53-69% lower than that in the control group, 67-60% in liver and 59-71% in gizzard

  1. The influence of pH on the adsorption of lead by Na-clinoptilolite ...

    African Journals Online (AJOL)

    The influence of pH on the adsorption of lead by Na-clinoptilolite: Kinetic and equilibrium studies. ... At high pH of the contact solution, the adsorption process occurs by ion exchange and at low pH; i.e., it is physical. The variation of the Gibbs free energy demonstrates that adsorption occurs spontaneously. The process was ...

  2. Boron adsorption on hematite and clinoptilolite

    International Nuclear Information System (INIS)

    Gainer, G.M.

    1993-01-01

    This thesis describes experiments performed to determine the suitability of boron as a potential reactive tracer for use in saturated-zone C-well reactive tracer studies for the Yucca Mountain Project (YMP). Experiments were performed to identify the prevalent sorption mechanism of boron and to determine adsorption of boron on hematite and clinoptilolite as a function of pH. These minerals are present in the Yucca Mountain tuff in which the C-well studies will be conducted. Evaluation of this sorption mechanism was done by determining the equilibration time of boron-mineral suspensions, by measuring changes in equilibrium to titrations, and by measuring electrophoretic mobility. Experiments were performed with the minerals suspended in NaCl electrolytes of concentrations ranging from 0.1 N NaCl to 0.001 N NaCl. Experimentalconditions included pH values between 3 and 12 and temperature of about 38 degrees C

  3. A density functional theory study of arsenic immobilization by the Al(III)-modified zeolite clinoptilolite

    NARCIS (Netherlands)

    Awuah, Joel B.; Dzade, N.Y.; Tia, Richard; Adei, Evans; Kwakye-Awuah, Bright; Catlow, C. Richard A.; de Leeuw, Nora H.

    2016-01-01

    We present density functional theory calculations of the adsorption of arsenic acid (AsO(OH)3) and arsenous acid (As(OH)3) on the Al(III)-modified natural zeolite clinoptilolite under anhydrous and hydrated conditions. From our calculated adsorption energies, we show that adsorption of both arsenic

  4. Clean-up of liquid radiation wastes with elevated mineralization from cesium and cobalt radionuclides by the modified clinoptilolite of the Chankanaj deposit

    International Nuclear Information System (INIS)

    Plotnikov, V.I.; Tuleushev, A.Zh.; Zhabykbaev, G.T.; Kostsov, S.V.; Medvedeva, Z.V.; Plotnikova, O.M.; Chakrova, E.T.; Idrisova, U.R.; Idrisova, D.Zh.

    2003-01-01

    On the base of laboratory studies and semi-industrial testing the possibility of liquid radioactive wastes clean-up from cesium and cobalt radionuclides in elevated mineralization conditions with help of modified clinoptilolite is shown. In the work the synthesized thin-layer inorganic sorbent (TIS) with conventional name MC-2 (modified clinoptilolite) was used. The Chankanaj deposit's zeolite in the crushed form was base for the TIS production. The copper ferrocyanides serves as the modifier. This sorbent is selective one in relationship to cesium and cobalt radionuclides

  5. Regeneration of clinoptilolite zeolite used for the ammonium removal

    International Nuclear Information System (INIS)

    Garcia G, M.C.

    2002-01-01

    The use of zeolites has been increased in the last years with different applications and with a great boom in the environmental area, but a little had been make about the regeneration of such zeolites. The presence of nitrogen-ammonia in water may cause serious pollution problems since it results to be toxic for fishes and other aquatic life forms, also it provokes the algae growing. The natural clinoptilolite contains interchangeable ions such as the sodium (Na + ), potassium (K + ), magnesium (Mg 2+ ) and calcium (Ca 2+ ) in different proportions depending on the mineral origin When the zeolite is upgraded to its sodium form, the cation exchange capacity and the preference by the nitrogen-ammonia are increased, allowing the reversible process of sorption. In this work it was proposed the regeneration to its sodium form about the ammonia clinoptilolite zeolite. The natural mineral was characterized using the methods such as: X-ray diffraction, Infrared spectroscopy, Thermal gravimetric analysis and surface area. The results show that the ammonium sorption was between 95% and 98.7% such an ambient temperature as a flow back. the zeolite was regenerated approximately from 60% in the first cycle up to 97% in the last cycle at flow back temperature and of 59.2% up to 96.9% at ambient temperature, it was not presented any significant effect which could be attributed to the temperature. During the exchange process, the cations present in the natural zeolite were exchanged with the ammonium ions, this process was not completed due to that retained ammonium quantity was major that of the desorpted ions, what shows that in addition of ion exchange, another type of sorption process exists. (Author)

  6. Ultrasound-assisted dispersive solid phase extraction of cadmium(II) and lead(II) using a hybrid nanoadsorbent composed of graphene and the zeolite clinoptilolite

    International Nuclear Information System (INIS)

    Ghazaghi, Mehri; Mousavi, Hassan Zavvar; Shirkhanloo, Hamid; Rashidi, Ali Morad

    2015-01-01

    We describe a hybrid nanoadsorbent prepared by depositing graphene on the zeolite clinoptilolite by chemical vapor deposition. The resulting sorbent is well suited for the preconcentration of lead(II) and cadmium(II) by ultrasound-assisted dispersive micro solid–phase extraction. An extraction unit has been designed and manufactured that facilitates handling of small sample volumes. The effects of sample pH, amount of sorbent, concentration and volume of elution and time of ultrasonic bath were investigated. The nanoadsorbent was characterized by scanning electron microscopy, X-ray diffraction and energy dispersive X-ray microanalysis, all of which revealed the high surface area of the graphene sheets on the clinoptilolite. The extraction recoveries when using the new nanoadsorbent are 97 % (as opposed to a mere 10 % in case of clinoptilolite only). It is assumed that the graphene sheets located around the porous structure of clinoptilolite are acting as a barrier against macromolecules potentially existing in the sample matrices. The method was applied to the determination of lead and cadmium in water and human serum samples by electrothermal atomic absorption spectrometry. The detection limits were as low as 70 and 4 ng L −1 for Pb(II) and Cd(II), respectively. The accuracy of the method was underpinned by correct analysis of a standard reference material (SRM: 203105 Seronorm Trace Elements Serum L-2). (author)

  7. Natural clinoptilolite exchanged with iron: characterization and catalytic activity in nitrogen monoxide reduction

    Directory of Open Access Journals (Sweden)

    Daria Tito-Ferro

    2016-12-01

    Full Text Available The aim of this work was to characterize the natural clinoptilolite from Tasajeras deposit, Cuba, modified by hydrothermal ion-exchange with solutions of iron (II sulfate and iron (III nitrate in acid medium. Besides this, its catalytic activity to reduce nitrogen monoxide with carbon monoxide/propene in the presence of oxygen was evaluated. The characterization was performed by Mössbauer and UV-Vis diffuse reflectance spectroscopies and adsorption measurements. The obtained results lead to conclude that in exchanged samples, incorporated divalent and trivalent irons are found in octahedral coordination. Both irons should be mainly in cationic extra-framework positions inside clinoptilolite channels as charge compensating cations, and also as iron oxy-hydroxides resulting from limited hydrolysis of these cations. The iron (III exchanged samples has a larger amount of iron oxy-hydroxides agglomerates. The iron (II exchanged samples have additionally iron (II sulfate adsorbed. The catalytic activity in the nitrogen monoxide reduction is higher in the exchanged zeolites than starting. Among all samples, those exchanged of iron (II has the higher catalytic activity. This lead to outline that, main catalytically active centers are associated with divalent iron.

  8. AFCF and clinoptilolite use in reduction of {sup 137}Cs deposition in several days' contaminated broiler chicks

    Energy Technology Data Exchange (ETDEWEB)

    Mitrovic, B. [Faculty of Veterinary Medicine, Department of Radiology, 18 Bulevar JA, 11 000 Belgrade (Serbia)]. E-mail: radijacija@vet.bg.ac.yu; Vitorovic, G. [Faculty of Veterinary Medicine, Department of Radiology, 18 Bulevar JA, 11 000 Belgrade (Serbia); Vitorovic, D. [Faculty of Agriculture, Department of Animal Science, 6 Nemanjina, 11 080 Belgrade (Serbia); Dakovic, A. [Institute for Technology of Nuclear and Other Raw Materials, 86 Franche D' Epere, 11 000 Belgrade (Serbia); Stojanovic, M. [Institute for Technology of Nuclear and Other Raw Materials, 86 Franche D' Epere, 11 000 Belgrade (Serbia)

    2007-06-15

    The objective of this study was to investigate the binding efficiency of AFCF and clinoptilolite, mixed to the feed and administered orally using gastric tube to chronically {sup 137}Cs alimentary contaminated broiler chicks. Seventy-five male Hybro broiler chicks, between 35 and 47 days of age were divided into five groups (15 birds per group) reared in cages (five birds in a cage) and fed a standard diet. Every day during 13 days of the experimental period all chicks received orally 1 ml CsCl water solution with activity of 1310 Bq ml{sup -1} {sup 137}Cs (gastric tube). Group 1 was the control group and received no binders. The experimental groups received the binders. Group 2 received 0.2 g of AFCF in the form of water solution (gastric tube); group 3 received 0.2% AFCF in the feed; group 4 received 2 g clinoptilolite in the form of water suspension (gastric tube) and group 5 received 2% clinoptilolite in the feed. Five chicks from each group were sacrificed on days 4, 10 and 13 of the experimental period. Using gamma spectrometric methods specific activity of {sup 137}Cs was determined in the samples of breast meat, liver and gizzard. The results obtained showed that administering binders to the chronically contaminated broiler chicks significantly (p < 0.01) reduced {sup 137}Cs transfer and deposition in breast meat, liver and gizzard. Decreasing deposition of {sup 137}Cs in breast meat and internal organs increased with time of contamination and binders' administration. With AFCF as a cesium binder, on day 13 of measuring the {sup 137}Cs activity in breast meat was 80-83% lower than that in the control group, 89% in liver and 83-84% in gizzard. Natural clinoptilolite demonstrated lower binding efficiency. On day 13 of measuring the {sup 137}Cs activity in breast meat was 53-69% lower than that in the control group, 67-60% in liver and 59-71% in gizzard.

  9. Potentiated clinoptilolite: artificially enhanced aluminosilicate reduces symptoms associated with endoscopically negative gastroesophageal reflux disease and nonsteroidal anti-inflammatory drug induced gastritis

    Directory of Open Access Journals (Sweden)

    Potgieter W

    2014-07-01

    Full Text Available Wilna Potgieter, Caroline Selma Samuels, Jacques Renè SnymanDepartment of Pharmacology, School of Medicine, Faculty of Health Sciences, University of Pretoria, Pretoria, Gauteng, South AfricaPurpose: The cation exchanger, a potentiated clinoptilolite (Absorbatox™ 2.4D, is a synthetically enhanced aluminosilicate. The aim of this study was to evaluate the possible benefits of a potentiated clinoptilolite as a gastroprotective agent in reducing the severity of clinical symptoms and signs associated with 1 endoscopically negative gastroesophageal reflux disease (ENGORD and 2 nonsteroidal anti-inflammatory drug (NSAID medication.Methods and patients: Two randomized, double-blind, placebo-controlled, pilot studies, the ENGORD and NSAID studies, were conducted. After initial negative gastroscopy, a total of 25 patients suffering from ENGORD were randomized to receive either placebo capsules or 750 mg Absorbatox twice daily for 14 days. The NSAID study recruited 23 healthy patients who received orally either 1,500 mg Absorbatox or placebo three times daily, plus 500 mg naproxen twice daily. Patients underwent gastroscopic evaluation of their stomach linings prior to and on day 14 of the study. Gastric biopsies were obtained and evaluated via the upgraded Sydney system, whereas visible gastric events and status of the gastric mucosa were evaluated via a 0–3 rating scale. During both studies, patients recorded gastric symptoms in a daily symptom diary.Results: In the ENGORD study, patients who received the potentiated clinoptilolite reported a significant reduction (P≤0.05 in severity of symptoms including reduction in heartburn (44%, discomfort (54%, and pain (56%. Symptom-free days improved by 41% compared to the group who received placebo (not significant. This was over and above the benefits seen with the proton pump inhibitor. In the NSAID study, the reduction in gastric symptom severity was echoed in the group who received the potentiated

  10. Influences of clinoptilolite and surfactant-modified clinoptilolite zeolite on nitrate leaching and plant growth

    International Nuclear Information System (INIS)

    Malekian, Raheleh; Abedi-Koupai, Jahangir; Eslamian, Sayed Saeid

    2011-01-01

    The increasing demands for environmental protection and sustainable food production require an increase in the use of natural and non-toxic materials for agriculture. In this study, the feasibility of using surfactant-modified zeolite (SMZ) in comparison with zeolite clinoptilolite (Cp) application to reduce nitrate leaching and enhance crop growth was investigated. The effects of size (millimeter and nanometer) and application rate (20 g kg -1 and 60 g kg -1 ) of Cp and SMZ on nitrate leaching and crop response were also evaluated. Using soil lysimeters, it was determined that the maximum and mean nitrate concentration in the leachate of SMZ-amended soil were significantly (p 3 -N leached from SMZ- and Cp-amended lysimeters at the higher application rate (60 g kg -1 ) was approximately 26% and 22% lower, respectively, than that from the control system. The mean grain yield, grain nitrogen content, stover dry matter, and N uptake were significantly greater in Cp-amended than SMZ-amended lysimeters. There was no significant effect due to the particle size of the two soil amendments. The results implicitly suggest that plants may have a better response if Cp is used as a fertilizer carrier rather than SMZ when applied at a rate of 60 g kg -1 .

  11. Ammonium removal from aqueous solutions by clinoptilolite: determination of isotherm and thermodynamic parameters and comparison of kinetics by the double exponential model and conventional kinetic models.

    Science.gov (United States)

    Tosun, Ismail

    2012-03-01

    The adsorption isotherm, the adsorption kinetics, and the thermodynamic parameters of ammonium removal from aqueous solution by using clinoptilolite in aqueous solution was investigated in this study. Experimental data obtained from batch equilibrium tests have been analyzed by four two-parameter (Freundlich, Langmuir, Tempkin and Dubinin-Radushkevich (D-R)) and four three-parameter (Redlich-Peterson (R-P), Sips, Toth and Khan) isotherm models. D-R and R-P isotherms were the models that best fitted to experimental data over the other two- and three-parameter models applied. The adsorption energy (E) from the D-R isotherm was found to be approximately 7 kJ/mol for the ammonium-clinoptilolite system, thereby indicating that ammonium is adsorbed on clinoptilolite by physisorption. Kinetic parameters were determined by analyzing the nth-order kinetic model, the modified second-order model and the double exponential model, and each model resulted in a coefficient of determination (R(2)) of above 0.989 with an average relative error lower than 5%. A Double Exponential Model (DEM) showed that the adsorption process develops in two stages as rapid and slow phase. Changes in standard free energy (∆G°), enthalpy (∆H°) and entropy (∆S°) of ammonium-clinoptilolite system were estimated by using the thermodynamic equilibrium coefficients.

  12. Ammonium Removal from Aqueous Solutions by Clinoptilolite: Determination of Isotherm and Thermodynamic Parameters and Comparison of Kinetics by the Double Exponential Model and Conventional Kinetic Models

    Directory of Open Access Journals (Sweden)

    İsmail Tosun

    2012-03-01

    Full Text Available The adsorption isotherm, the adsorption kinetics, and the thermodynamic parameters of ammonium removal from aqueous solution by using clinoptilolite in aqueous solution was investigated in this study. Experimental data obtained from batch equilibrium tests have been analyzed by four two-parameter (Freundlich, Langmuir, Tempkin and Dubinin-Radushkevich (D-R and four three-parameter (Redlich-Peterson (R-P, Sips, Toth and Khan isotherm models. D-R and R-P isotherms were the models that best fitted to experimental data over the other two- and three-parameter models applied. The adsorption energy (E from the D-R isotherm was found to be approximately 7 kJ/mol for the ammonium-clinoptilolite system, thereby indicating that ammonium is adsorbed on clinoptilolite by physisorption. Kinetic parameters were determined by analyzing the nth-order kinetic model, the modified second-order model and the double exponential model, and each model resulted in a coefficient of determination (R2 of above 0.989 with an average relative error lower than 5%. A Double Exponential Model (DEM showed that the adsorption process develops in two stages as rapid and slow phase. Changes in standard free energy (∆G°, enthalpy (∆H° and entropy (∆S° of ammonium-clinoptilolite system were estimated by using the thermodynamic equilibrium coefficients.

  13. Intestinal Development and Function of Broiler Chickens on Diets Supplemented with Clinoptilolite

    Directory of Open Access Journals (Sweden)

    Q. J. Wu

    2013-07-01

    Full Text Available The purpose of this study was to evaluate the effect of natural clinoptilolite (NCLI and modified clinoptilolite (MCLI on broiler performance, gut morphology, intestinal length and weight, and gut digestive enzyme activity. A total of 240 d-old male chicks were randomly assigned to 3 treatments, each of which comprised 8 pens of 10 chicks per pen. Birds in the control group were fed the basal diet, while those in the experimental groups were fed diets supplemented with NCLI at 2% (NCLI group, or MCLI at 2% (MCLI group, respectively, for 42 d. Compared with the control, supplementation with NCLI or MCLI had no significant (p>0.05 effects on productive parameters from d 1 to 42. Supplementation with NCLI or MCLI had no influence on the relative length and weight of small intestine at d 1 to 21. But supplementation with NCLI or MCLI significantly reduced the relative weight of duodenum. Supplementation with MCLI and NCLI was associated with greater (p0.05 influence on the crypt depth in the jejunal and ileal mucosa compared with those in the controls. The addition of either NCLI or MCLI to the diet improved the activities of total protease, and amylase in the small intestinal contents. In conclusion, supplementation with NCLI or MCLI in diets improved intestinal morphology, increased the intestinal length and weigh and gut digestive enzyme activity.

  14. Leaching and antimicrobial properties of silver nanoparticles loaded onto natural zeolite clinoptilolite by ion exchange and wet impregnation

    CSIR Research Space (South Africa)

    Missengue, RNM

    2015-11-01

    Full Text Available This study aimed to compare the leaching and antimicrobial properties of silver that was loaded onto the natural zeolite clinoptilolite by ion exchange and wet impregnation. Silver ions were reduced using sodium borohydride (NaBH(sub4...

  15. Inhibition of bcl-2 and cox-2 Protein Expression after Local Application of a New Carmustine-Loaded Clinoptilolite-Based Delivery System in a Chemically Induced Skin Cancer Model in Mice

    Directory of Open Access Journals (Sweden)

    Cristina Mihaela Ghiciuc

    2017-11-01

    Full Text Available Our research has focused on in vitro and in vivo evaluations of a new Carmustine (BCNU-loaded clinoptilolite-based delivery system. Two clinoptilolite ionic forms—hydrogen form (HCLI and sodium form (NaCLI—were prepared, allowing a loading degree of about 5–6 mg BCNU/g of zeolite matrix due to the dual porous feature of clinoptilolite. Clinoptilolite-based delivery systems released 35.23% of the load in 12 h for the BCNU@HCLI system and only 10.82% for the BCNU@NaCLI system. The BCNU@HCLI system was chosen to develop gel and cream semisolid dosage forms. The cream (C_BCNU@HCLI released 29.6% of the loaded BCNU after 12 h in the Nylon synthetic membrane test and 31.6% in the collagen membrane test, higher by comparison to the gel. The new cream was evaluated in vivo in a chemically induced model of skin cancer in mice. Quantitative immunohistochemistry analysis showed stronger inhibition of B-cell lymphoma-2 (bcl-2 and cyclooxygenase 2 (cox-2 protein expression, known markers for cancer survival and aggressiveness, after the treatment with C_BCNU@HCLI by comparison to all the control treatment types, including an off-label magistral formula commercially available Carmustine cream as reference, bringing evidence that a clinoptilolite-based delivery systems could be used as a cancer drug carriers and controlled release systems (skin-targeted topical delivery systems.

  16. Removal of ammonia from waste air streams with clinoptilolite tuff in its natural and treated forms

    Czech Academy of Sciences Publication Activity Database

    Ciahotný, K.; Melenová, L.; Jirglová, H.; Prokopová, Olga; Kočiřík, Milan; Eić, M.

    2006-01-01

    Roč. 12, č. 3 (2006), s. 219-226 ISSN 0929-5607 R&D Projects: GA ČR GA104/00/1007; GA ČR GP104/03/D183 Institutional research plan: CEZ:AV0Z40400503 Keywords : clinoptilolite tuffs * ammonia * adsorption * impregnation Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 0.590, year: 2006

  17. A study on ammonia removal properties using clinoptilolite Part 1 : characterization of clinoptilolite and ammonia removal properties in batch reactor

    Energy Technology Data Exchange (ETDEWEB)

    Moon, Jeong Min; Chung, Jong Shik [Dept. of Chemical Engineering/School of Environment Engineering, Pohang University of Science and Technology, Pohang (Korea); Sun, De Shi [Dept. of Applied Chemistry, Harbin Institute of Techonology (China)

    2000-04-01

    A natural zeolite, deposit located at Guryongpo, Young-il bay, was found to be clinoptilolite containing impurities of heulandite and mordenite. Cation exchange capacity(CEC) for ammonia was about 1.41 meq/g from Na{sup +}-form of the zeolite. In batch experiment, removal efficiency of ammonia was increased as particle size of zeolite and initial concentration of Na{sup +} were decreased and SR(Stoichiometric Ratio), time, and initial concentration of ammonia increased. More than 70% aluminum ion could be removed from water having 3 ppm ammonia and 0.7 ppm Al{sup 3+} by the batch adsorption(ion exchange) experiment. Regeneration of used zeolite with NaCl solution of pH=12 has shown more than 95% of regeneration efficiency when SR'(ratio of the amount of NaCl solution employed actually to the amount in a stoichiometric quantity) was equal to 2.0. 19 refs., 10 figs., 1 tab.

  18. Comparative study of cerium (IV) sorptive properties in zeolite Y and clinoptilolite; Estudio comparativo de la fijacion de cerio (IV) en zeolitas, faujasita-Y y clinoptilolita

    Energy Technology Data Exchange (ETDEWEB)

    Garcia D, O C

    1994-12-31

    Among the problems of protecting the environment from radioactive contamination, the reduction of radioactive releases by improving monitoring, decontamination, and burial methods is one of the most important. Natural sorbents are gaining increased significance for solving this problem. Among these, zeolites deserve special attention since they have sufficient sorptive capacity, are highly radiation resistant, are widely distributed exhibit selectivity and are inexpensive. In the present work we determine experimentally the sorptive characteristics of clinoptilolite as a function of various factors and demonstrate that clinoptilolite is capable of sorbing Ce(IV) over a wide pH range. (Author).

  19. Mineralogy and clinoptilolite K/Ar results from Yucca Mountain, Nevada, USA: A potential high-level radioactive waste repository site

    International Nuclear Information System (INIS)

    WoldeGabriel, G.; Broxton, D.E.; Bish, D.L.; Chipera, S.J.

    1993-11-01

    The Yucca Mountain Site Characterization Project is investigating Yucca Mountain, Nevada, as a potential site for a high-level nuclear waste repository. An important aspect of this evaluation is to understand the geologic history of the site including the diagenetic processes that are largely responsible for the present-day chemical and physical properties of the altered tuffs. This study evaluates the use of K/Ar geochronology in determining the alteration history of the zeolitized portions of Miocene tuffs at Yucca Mountain. Clinoptilolite is not generally regarded as suitable for dating because of its open structure and large ion-exchange capacity. However, it is the most abundant zeolite at Yucca Mountain and was selected for this study to assess the feasibility of dating the zeolitization process and/or subsequent processes that may have affected the zeolites. In this study we examine the ability of this mineral to retain all or part of its K and radiogenic Ar during diagenesis and evaluate the usefulness of the clinoptilolite K/Ar dates for determining the history of alteration

  20. Clinoptilolite and palygorskite as sorbents of neutral emerging organic contaminants in treated wastewater: Sorption-desorption studies.

    Science.gov (United States)

    Leal, María; Martínez-Hernández, Virtudes; Meffe, Raffaella; Lillo, Javier; de Bustamante, Irene

    2017-05-01

    Water reuse for aquifer recharge could be an important route for the introduction of emerging organic contaminants (EOCs) into the environment. The installation of a Horizontal Permeable Reactive Barrier (H-PRB) could constitute a tertiary treatment process to remove EOCs from treated domestic wastewater prior to recharge activities. The sorption-desorption behaviour of six neutral EOCs present in treated domestic wastewater (acetaminophen, caffeine, carbamazepine, cotinine, 4-acetamidoantipyrine (4-AAA) and 4-formylaminoantipyrine (4-FAA)) has been evaluated. Clinoptilolite and palygorskite have been studied as sorbents to be installed in the H-PRB. Batch tests were carried out using an EOC initial concentration ranging from 5 to 100 μg L -1 . Apart from acetaminophen and caffeine, both materials showed a limited sorption capacity of neutral EOCs (K d  = 0.63-5.42 L kg -1 ). In general, the experimental results show that EOCs exhibit a higher sorption affinity for clinoptilolite than for palygorskite. With the exception of carbamazepine, the sorption of the compounds occurs mainly by interactions with mineral surfaces as indicated by the comparison of the partition coefficients into organic matter and into mineral surfaces. According to the molecular geometry of the compounds and the sorption sequences observed, it appears that the dimensions of the organic molecules play a key role in the sorption process. All the studied EOCs exhibit irreversible sorption and sorption-desorption hysteresis. Copyright © 2017 Elsevier Ltd. All rights reserved.

  1. INVESTIGATION OF CLINOPTILOLITE NATURAL ZEOLITE REGENERATION BY AIR STRIPPING FOLLOWED BY ION EXCHANGE FOR REMOVAL OF AMMONIUM FROM AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    A. R. Rahmani ، M. T. Samadi ، H. R. Ehsani

    2009-07-01

    Full Text Available The purpose of this study was to regenerate clinoptilolite natural zeolite by air stripping followed by removal of ammonium from aqueous solutions. The research was carried out in continuous system. The characteristics of graded clinoptilolite from Semnan (one of the central provinces in Iran mines were determined and then regeneration tests were done by contacting of 1 N NaCl solution with given weights of ammonium saturated zeolite. Then the brine of column was transferred to the air stripping column for regeneration. The pH of brine solution before entrance to a stripping column was increased to 11. Air stripped ammonia from the brine was converted to the ammonium ion by using acid scrubber. The outlet effluent from stripping column was collected for reuse. The results showed that the cation exchange capacities were 17.31 to 18.38 mg NH4+/g of zeolite weight. Regeneration efficiency of zeolite by NaCl solution and air stripping was in the range of 92%-97% under various operational conditions. However, the efficiency of acid absorption of released ammonia in stripping process was 55% with a major rejection of the surplus ammonia to the atmosphere. It could be concluded that the method studied may be considered as an advanced and supplementary process for treating effluents of aqueous solution and fishponds in existing treatment plants.

  2. Immobilisation of 137Cs and 90Sr in hot-pressed clinoptilolite

    International Nuclear Information System (INIS)

    Briggs, A.; Jones, D.V.C.; Cole, G.B.; Valentine, T.M.; Preston, R.F.; Hawes, R.W.M.; Fones, M.D.

    1984-07-01

    It is shown that clinoptilolites from Nevada and Mudhills, California, can be vitrified by hot-pressing at 1000 to 1050 deg C for 30 min under 23 MPa pressure in graphite dies, or for 10 min under 3.5 MPa pressure in stainless steel bellows-shaped containers. Activity measurements before and after hot-pressing show that the radionuclides 137 Cs and 90 Sr are retained almost completely during the process. The hot-pressed material is shown to be extremely resistant to leaching of the nuclides, either in Soxhlet or long-term static leach tests. Gamma-irradiation increases their leachability; that of 90 Sr more than that of 137 Cs, but even so, the leach rates of both remain very low. X-ray diffraction spectra taken before and after heat-treatment for 10 days at temperatures up to 1000 deg C show no deleterious effects, and hydrothermal treatments at temperatures up to 90 deg C for 100 days, even in the presence of sodium ions in solution, are shown not to cause any changes detectable by X-ray diffraction. (author)

  3. THE EFFECT OF WATER CAPACITY ON THE ACTIVITY OF PD(II-CU(II CATALYST ANCHORED TO ACID-MODIFIED CLINOPTILOLITE IN THE REACTION OF LOW-TEMPERATURE CARBON MONOXIDE OXIDATION

    Directory of Open Access Journals (Sweden)

    T. L. Rakitskaya

    2015-02-01

    Full Text Available The maximum activity of Pd(II-Cu(II catalyst anchored to acid modified clinoptilolite in the reaction of low-temperature carbon monoxide oxidation with air oxygen has been found at the water content in the range from 3.3 to 4.2 mmol/g.

  4. Determination of {sup 60}Co sorption in natural clinoptilolite; Determinacion de la sorcion de {sup 60}Co en clinoptilolita natural

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez B, E.; Granados C, F. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1997-07-01

    It was studied the clinoptilolite behavior coming from a deposit in Taxco, Guerrero in hydration and stabilization conditions with sodium for determining its sorption properties. The ion exchange process was carried out through gamma spectrometry using a CoCl{sub 2} solution marked with {sup 60} Co at p H 6.5 in different contact times. It was observed a maximum sorption of 0.408 m eq Co{sup +2}/g mineral, from 0.314 m eq Co{sup +2}/g mineral correspond at ion exchange. (Author)

  5. Effect of the temperature on the sorption of cadmium in natural clinoptilolite from the State of Chihuahua

    International Nuclear Information System (INIS)

    Arambula V, V.

    2004-01-01

    The investigation works related with the removal of cadmium of aqueous solutions, they make emphasis in a great number of materials that were used for this end, as well as in the parameters that influence, such as the temperature and the pH. In this work it was investigated the effect of the temperature on the removal of cadmium, using a zeolitic mineral native of the State of Chihuahua for they were determined it kinetic parameters, those diffusivity coefficients and the retention mechanisms (adsorption or ion exchange) involved. The clinoptilolite samples were characterized by means of scanning electron microscopy in high vacuum (MEB), elementary microanalysis (EDS) and X-ray diffraction (XRD). The experimental part consisted on putting in contact solutions of cadmium with the mineral, varying the temperature, the time of contact or the concentration; the quantification of sodium and cadmium in the liquid phase was carried out by means of atomic absorption spectroscopy (EAA). It was determined the time of equilibrium for the removal process. The temperature and the concentration influence on the process of sorption of cadmium in the zeolitic mineral (kinetics and isotherms). The kinetic model that describes better the sorption process of cadmium in the clinoptilolite was the pseudo-2 order. The apparent coefficient of diffusivity presented a greater value conforms to increment the temperature. The results of the isotherm of adsorption of cadmium presented a better adjustment to the Freundlich model. The quantity of cadmium retained by the mineral it was greater than the quantity of sodium found in the solution after the contact between the solution of cadmium and the zeolitic mineral and in accordance with the obtained separation factors, the natural zeolite shows a greater affinity for the cadmium that for the sodium (α > 1). (Author)

  6. Review of the thermal stability and cation exchange properties of the zeolite minerals clinoptilolite, mordenite, and analcime; applications to radioactive waste isolation in silicic tuff

    International Nuclear Information System (INIS)

    Smyth, J.R.; Caporuscio, F.A.

    1981-06-01

    Silicic tuffs of the southern Great Basin and basalts of the Columbia River Plateau are under investigation as potential host rocks for high- and intermediate-level radioactive wastes. Nonwelded and partially welded tuffs may contain major amounts (> 50%) of the zeolite minerals clinoptilolite, mordenite, and analcime. Densely welded tuffs and some basalt flows may contain clinoptilolite as fracture filling that limits the permeability of these rocks. The cation exchange properties of these zeolite minerals allow them to pose a formidable natural barrier to the migration of cationic species of various radionuclides in aqueous solutions. However, these minerals are unstable at elevated temperatures and at low water-vapor pressures and may break down either by reversible dehydration or by irreversible mineralogical reactions. All the breakdown reactions occurring at increased temperature involve a net volume reduction and evolution of fluids. Thus, they may provide a pathway (shrinkage fractures) and a driving force (fluid pressure) for release of radionuclides to the biosphere. These reactions may be avoided by keeping zeolite-bearing horizons saturated with water and below about 85 0 C. This may restrict allowable gross thermal loadings in waste repositories in volcanic rocks

  7. Surface effect of natural zeolite (clinoptilolite) on the photocatalytic activity of TiO2

    International Nuclear Information System (INIS)

    Li Fangfei; Jiang Yinshan; Yu Lixin; Yang Zhengwen; Hou Tianyi; Sun Shenmei

    2005-01-01

    The surface interaction between TiO 2 and natural zeolite, clinoptilolite, has been investigated by means of transmission electron microscope (TEM), atom force microscope (AFM), X-ray diffractometer (XRD), diffuse reflectance infrared Fourier transform (DRIFT) and far Fourier transform infrared ray (FTIR) spectroscopy. And the photocatalytic degradation (PCD) rate of methyl orange (MO), a model of recalcitrant azo dye, in aqueous system has been measured to compare the photocatalytic activities of different photocatalysts. A model has been carried out to explain the incorporation between TiO 2 particles and natural zeolite. The results show that the TiO 2 particles loaded on zeolite are 50 nm or so, smaller than the pure one, and combine with zeolite via chemical force. Since the reserved adsorption ability and the existence of electron trapper, the TiO 2 -zeolite performed more efficient at low initial concentration and in the later period of PCD process, as compared with pure TiO 2 nanopowders

  8. Effect of zeolite (clinoptilolite) as feed additive in Tunisian broilers on the total flora, meat texture and the production of omega 3 polyunsaturated fatty acid

    Science.gov (United States)

    2012-01-01

    Background Increasing consumer demand for healthier food products has led to the development of governmental policies regarding health claims in many developed countries. In this context, contamination of poultry by food-borne pathogens is considered one of the major problems facing the progress of the poultry industry in Tunisia. Result Zeolite (Clinoptilolites) was added to chicken feed at concentrations 0,5% or 1% and was evaluated for its effectiveness to reduce total flora in chickens and its effects on performance of the production. The broilers were given free and continuous access to a nutritionally non-limiting diet (in meal form)that was either a basal diet or a' zeolite diet' (the basal diet supplemented with clinoptilolite at a level of 0,5% or 1%). It was found that adding zeolite in the broiler diet significantly (p zeolite treatment had a positive effect on performance production and organoleptic parameters that were measured and mainly on the increase level of Omega 3 fatty acid. Conclusion This study showed the significance of using zeolite, as a feed additive for broilers, as part of a comprehensive program to control total flora at the broiler farm and to increase level of Omega 3 fatty acid on the chicken body. PMID:22394592

  9. Synthesis, characterization and drug release properties of 3D chitosan/clinoptilolite biocomposite cryogels.

    Science.gov (United States)

    Dinu, Maria Valentina; Cocarta, Ana Irina; Dragan, Ecaterina Stela

    2016-11-20

    Three-dimensional (3D) biocomposites based on chitosan (CS) and clinoptilolite (CPL) were prepared by cryogelation and their potential application as drug carriers was investigated. Variation of CPL content from 0 to 33wt.% allowed the formation of biocomposites with heterogeneous morphologies consisting of randomly distributed pores. The further increase of CPL content led to ordered porous architectures where parallel pore channels were observed. The CPL content had a strong influence on water uptake, as well as on the cumulative release of diclofenac sodium (DS) and indomethacin (IDM). It was demonstrated that the drug delivery preferentially takes place in phosphate buffer saline (pH 7.4) in comparison to simulated gastric fluid (pH 1.2), where only a reduced drug release was observed. The drug release mechanism dominating these systems is described as a pseudo-Fickian diffusion, but it changes to non-Fickian release when 33wt.% of CPL was entrapped into the CS matrix or when IDM was loaded into biocomposites. Copyright © 2016 Elsevier Ltd. All rights reserved.

  10. Regeneration of clinoptilolite zeolite used for the ammonium removal; Regeneracion de zeolita clinoptilolita empleada para la remocion de amonio

    Energy Technology Data Exchange (ETDEWEB)

    Garcia G, M C

    2002-07-01

    The use of zeolites has been increased in the last years with different applications and with a great boom in the environmental area, but a little had been make about the regeneration of such zeolites. The presence of nitrogen-ammonia in water may cause serious pollution problems since it results to be toxic for fishes and other aquatic life forms, also it provokes the algae growing. The natural clinoptilolite contains interchangeable ions such as the sodium (Na{sup +}), potassium (K{sup +}), magnesium (Mg{sup 2+}) and calcium (Ca{sup 2+}) in different proportions depending on the mineral origin When the zeolite is upgraded to its sodium form, the cation exchange capacity and the preference by the nitrogen-ammonia are increased, allowing the reversible process of sorption. In this work it was proposed the regeneration to its sodium form about the ammonia clinoptilolite zeolite. The natural mineral was characterized using the methods such as: X-ray diffraction, Infrared spectroscopy, Thermal gravimetric analysis and surface area. The results show that the ammonium sorption was between 95% and 98.7% such an ambient temperature as a flow back. the zeolite was regenerated approximately from 60% in the first cycle up to 97% in the last cycle at flow back temperature and of 59.2% up to 96.9% at ambient temperature, it was not presented any significant effect which could be attributed to the temperature. During the exchange process, the cations present in the natural zeolite were exchanged with the ammonium ions, this process was not completed due to that retained ammonium quantity was major that of the desorpted ions, what shows that in addition of ion exchange, another type of sorption process exists. (Author)

  11. The selection and performance of the natural zeolite clinoptilolite in British Nuclear Fuels' site ion exchange effluent plant, SIXEP

    International Nuclear Information System (INIS)

    Baxter, S.G.; Berghauser, D.C.

    1986-01-01

    SIXEP has been conducted by British Nuclear Fuels plc at its Sellafield reprocessing site as part of its committment to reduce radioactive discharges to the Irish Sea. An extensive development program identified the natural ion exchange mineral clinoptilolite, from a particular deposit in California now owned by Tenneco Specialty Minerals, as the most suitable for use in SIXEP to extract caesium and strontium from spent nuclear fuel storage pond water. Close cooperation with the supplier in a Quality Assurance scheme ensured the supply of a fully-characterised, high grade ion exchanger. Since SIXEP commenced treating pond water on 28 May 1985, the plant has performed well, exceeding the design expectation in terms of discharge reduction and availability

  12. Investigation of thermodynamic parameters of cetyl pyridinium bromide sorption onto ZSM-5 and natural clinoptilolite

    International Nuclear Information System (INIS)

    Ghiaci, M.; Kia, R.; Kalbasi, R.J.

    2004-01-01

    A study was undertaken to determine the influence of temperature and surfactant concentration on the adsorption of cetyl pyridinium bromide on two ZSM-5 zeolites, and on natural clinoptilolite. The effect of temperature on adsorption and thermodynamic properties was investigated by making measurements at (297, 303, 307, 313) K. The results show that the calculated curves from the general isotherm equation can represent the experimental data very well up to T=313 K. Based on the calculation of the thermodynamics of adsorption, it is evident that the principle contribution to the ΔG compfn hm of negative value is the large positive value of ΔS compfn hm (36 to 52 J · mol -1 ), whereas ΔH compfn hm is positive and in the range of 1 to 7 kJ · mol -1 . Therefore, similar to the micellisation in bulk solution, the second step of surfactant adsorption is an entropy-driven process

  13. Optimization of Manganese Reduction in Biotreated POME onto 3A Molecular Sieve and Clinoptilolite Zeolites.

    Science.gov (United States)

    Jami, Mohammed S; Rosli, Nurul-Shafiqah; Amosa, Mutiu K

    2016-06-01

    Availability of quality-certified water is pertinent to the production of food and pharmaceutical products. Adverse effects of manganese content of water on the corrosion of vessels and reactors necessitate that process water is scrutinized for allowable concentration levels before being applied in the production processes. In this research, optimization of the adsorption process conditions germane to the removal of manganese from biotreated palm oil mill effluent (BPOME) using zeolite 3A subsequent to a comparative adsorption with clinoptilolite was studied. A face-centered central composite design (FCCCD) of the response surface methodology (RSM) was adopted for the study. Analysis of variance (ANOVA) for response surface quadratic model revealed that the model was significant with dosage and agitation speed connoting the main significant process factors for the optimization. R(2) of 0.9478 yielded by the model was in agreement with predicted R(2). Langmuir and pseudo-second-order suggest the adsorption mechanism involved monolayer adsorption and cation exchanging.

  14. Sorption of cobalt in zeolites and natural clays of the clinoptilolite and kaolinite type

    International Nuclear Information System (INIS)

    Davila R, J.I.; Solache R, M.

    2006-01-01

    In this work the sorption of cobalt of aqueous solutions in two natural zeolites (clinoptilolite) and a clay (kaolinite) of origin in the center-north region of Mexico is evaluated. The effect of the pH and the time of contact in the process of sorption were evaluated. The cobalt retained in the aluminosilicates was determined by neutron activation analysis. The cobalt sorption in the materials in a range of pH from 4 to 7 does not present significant variations. The studies of reaction kinetics show a very fast sorption in the first 5 hours of contact, reaching the equilibrium in approximately 24 hours. The kinetics of sorption of the cobalt ions was represented better by the Ritchie reaction model modified of second order. The experimental data for the zeolites obtained at ambient temperature and varying the concentration were adjusted to the models of Freundlich, Langmuir and Freundlich-Langmuir isotherms and it was observed that the cobalt sorption it behaves according to the Freundlich isotherm model. (Author)

  15. Anchoring of CoHFC nanoparticles on clinoptilolite for remedy of nuclear wastes

    Directory of Open Access Journals (Sweden)

    Yousefi Taher

    2017-01-01

    Full Text Available To improve the mechanical properties, the cobalt ferrocyanide precipitation was carried out on clinoptilolite as an inorganic polymer. In this work the combination of two important factors, stability (zeolite and high adsorption capacity (cobalt ferrocyanide were considered to improve the ions uptake ability of adsorbent. The modification was approved by X-ray diffraction, Scanning electronic microscopy and Fourier transform infrared spectroscopy. The modified zeolite was applied to remove Sr(II and Cs(I ions from aqueous solution in a batch system. The adsorption capacities of modified zeolite for Cs(I and Sr(II improved to 90 and 130 mgg-1, respectively. The Sr(II and Cs(I removal were investigated as a function of shaking time, pH, Sr(II, and Cs(I initial concentration and temperature. The experimental data were fitted well to Langmuir isotherm model for two sorbet metal ions. The time dependence sorption data showed that the uptakes of Cs(I and Sr(II were very rapid and apparent sorption equilibriums were achieved within 100 min of contact time. The kinetic experimental data were fitted to the pseudo-first order, pseudo-second order, the double exponential, Elovich and intraparticle diffusion models. The sorption rates and capacities as well as rate constants were evaluated.

  16. Administration of Clinoptilolite to Broiler Chickens During Growth and Its Effect on the Growth Rate and Bone Metabolism Indicators

    Directory of Open Access Journals (Sweden)

    E. Straková

    2008-01-01

    Full Text Available The growth rate and bone metabolism indicators were monitored in broiler chickens receiving the feed supplemented with clinoptilolite. One-day-old broiler chickens ROSS 308 were divided into control (C and experimental (E groups with 100 males and 100 females per group. The chickens received the complete feed mixture BR1 from 1 to 10 days of age, followed by the feed mixture BR2 until the age of 30 days, and the feed mixture BR3 until the end of the experiment (40 days. The feed mixtures of the experimental group were supplemented with clinoptilolite (commercial additive ZeoFeed at a level of 0.5% (BR1, 1.5% (BR2 and 2.5% (BR3, replacing the corresponding portion of wheat. Feed mixtures and drinking water were provided ad libitum. The live weight of broiler chickens in both the control and experimental group increased steadily during the experiment. At the end of the experiment, live weights of experimental females (2,416 g and males (2,829 g were higher than those of control females (2,345 g and males (2,694 g by 3% and 5%, respectively. Significant differences in the live weight between groups were found from the age of 30 days (P ⪬ 0.05 and P ⪬ 0.01. At the age of 40 days, the chickens were slaughtered and the femur and tibiotarsus of the right leg were analysed for the content of dry matter, ash, calcium, phosphorus and magnesium. The ash content in dry matter ranged from 53.0 to 54.1% in group C and from 51.7 to 53.2% in group E. The Ca and P contents in dry matter in group E were lower than those in group C, except for Ca and P in the male tibiotarsus. In both groups, regardless of sex, the ash content was higher in the tibiotarsus than in the femur. Since fat levels in bones of the experimental group were increased (females by 19.5% in the femur and 21.3% in the tibiotarsus; males by 22.0% in the femur and 26.3% in the tibiotarsus, which could affect the values obtained, ash, calcium, phosphorus and magnesium were determined in the

  17. EDTA-functionalized clinoptilolite nanoparticles as an effective adsorbent for Pb(II) removal.

    Science.gov (United States)

    Eshraghi, Farahnaz; Nezamzadeh-Ejhieh, Alireza

    2018-03-08

    An efficient Pb(II) adsorbent was prepared by the modification of clinoptilolite nanoparticles (CpN) with ethylenediaminetetraacetic acid (EDTA). Samples were characterized by XRD, FT-IR, SEM, BET, TG-DTG, CHNS analyzer, and energy dispersive analysis X-ray spectroscopy (EDX). The experiments were designed by response surface methodology (RSM) based on central composite design (CCD) that suggested a quadratic model to predict the conditions and the interactions between the variables including adsorbent dosage, removal time, C Pb , and its solution pH. Adequacy of the suggested quadratic model was judged by ANOVA. The maximum Pb(II) removal of 0.27 mmol Pb(II) /g ads was achieved in optimal run including adsorbent dosage 2 g L -1 , removal time 271 min, C Pb 22.51 mmol L -1 , and Pb(II) solution pH 5.88. In binary metal cation systems including 1000 mg L -1 with respect to both Pb(II) and interfering cations, good selectivity of CpN-EDTA adsorbent was observed towards Pb(II) among the tested cations except Fe(III). Adsorption isotherm of lead removal by the adsorbent was well modeled by Langmuir equation, indicating a monolayer sorption of Pb(II) onto the adsorbent. The pseudo-second-order rate equation, indicating chemical reaction rate limiting step for the process, well modeled the kinetic of the process. An exothermic and spontaneous process was confirmed by the negative ∆H and ∆G.

  18. The use in grass production of clinoptilolite as an ammonia adsorbent and a nitrogen carrier

    Directory of Open Access Journals (Sweden)

    Milovanović Jelena

    2015-01-01

    Full Text Available The clinoptilolite-rich tuff (NZ from Zlatokop deposit (Vranjska Banja, Serbia has been studied as a nitrogen carrier for grass production. Mechanism of binding ammonium cations present in water solutions by NZ has been examined as well as possibility of adsorption of ammonia released in fresh cattle manure during its fermentation. The NH4+ binding from solutions proceeds via an ion-exchange process which follows the pseudo-second-order kinetics. Adsorption isotherms studied at 298-318 K follow the Freundlich isotherm equation. The NZ readily adsorbs ammonia liberated from manure and an addition of 10 wt.% of NZ to manure can preserve up to 90% of ammonia. The potential benefit of this effect has been examined in greenhouse pot experiments with the Italian ryegrass (Lolium multiflorum, var. Macho using three different types of soil (silty, clayey and sandy. The zeta potential measurements show that stability of their colloidal dispersions differs mutually and that addition of the NZ differently affects the stability and nitrogen cycling. All results indicate that NZ can be applied in grass production. [Projekat Ministarstva nauke Republike Srbije, br. 172018 and Norwegian Programme in Higher Education, Research and Development HERD

  19. Potentiated clinoptilolite reduces signs and symptoms associated with veisalgia

    Directory of Open Access Journals (Sweden)

    Gandy JJ

    2015-08-01

    Absorbatox™ resulted in an overall significant reduction in central nervous system and gastrointestinal tract symptoms associated with veisalgia, warranting further investigation. Keywords: hangover, clinoptilolite, Absorbatox, alcohol

  20. Reduction of radiocaesium transfer to broiler chicken meat by a clinoptilolite modified with hexacyanoferrate

    International Nuclear Information System (INIS)

    Poeschl, M.; Balas, J.

    1999-01-01

    The effect of RADEKONT (a natural clinoptilolite modified by hexacyanoferrate) on 137 Cs uptake into meat was tested in experiments with broiler chickens. Three experiments determined the influence of RADEKONT on radiocaesium transfer after single or repeated applications of artificially contaminated feed mixture and one experiment investigated the effect of RADEKONT when feeding a mixture containing wheat contaminated by the Chernobyl fallout. Independent of the effect of RADEKONT, the uptake of radiocaesium was faster in leg meat than in breast meat. Reduction factors ( 137 Cs transfer without the RADEKONT additive compared with those observed after supplementation of the additive into the feed mixture) of 1.1-1.3 and 1.2-2.3, respectively, were achieved after single and repeated administrations of artificially contaminated feed. No significant differences in reduction between breast and leg meat were observed. RADEKONT was more effective when the chickens were fed with Chernobyl-contaminated wheat (reduction factors of up to 3.7) than an artificial 137 Cs source. RADEKONT as a supplement during the decontamination period decreased the biological half-life of 137 C to less than 1 day. The timing of the application of RADEKONT might be important in determining its effectiveness, especially in young, rapidly growing chickens. (orig.)

  1. A Systematic Study on the Effect of Desilication of Clinoptilolite Zeolite on its Deep-Desulfurization Characteristics

    Directory of Open Access Journals (Sweden)

    Rahman Mahmoudi

    2016-07-01

    Full Text Available Natural clinoptilolite zeolite (CLP in its original or metal ion- exchanged form (Ni2+ is a weak adsorbent for relatively large thiophene derivative molecules like benzothiophene (BT and di-benzothiophene (DBT, due to its rather restricted micro-channel structure. A novelty of this work is that upon desilication treatments, it is possible to enhance the adsorption behavior of Ni2+-exchanged CLP for such large sulfur- containing molecules. A natural CLP zeolite has been desilicated using NaOH solutions in a concentration range of 0.2-2.0 M. The resulting powders have been subjected to XRF, XRD, FTIR, nitrogen adsorption/desorption, TEM and TGA analyses. The adsorption isotherms for the removal of thiophene (TP, BT, DBT and iso-propyl mercaptan (IPM have been obtained experimentally at 20 °C from simulated liquid fuels using iso-octane as solvent. The sample treated with 1.5 M NaOH solution showed the most significant enhancement in adsorptive properties. The selectivity order is IPM > TP > BT > DBT. Regenerability tests show a quasi constant adsorption capacity after the first cycle. The observed phenomena have been thoroughly discussed based on the physico-chemical analyses of the samples.

  2. On-site infiltration of a copper roof runoff: role of clinoptilolite as an artificial barrier material.

    Science.gov (United States)

    Athanasiadis, Konstantinos; Helmreich, Brigitte; Horn, Harald

    2007-08-01

    On-site infiltration may be considered as a promising way of managing rainwater runoffs in urban areas, provided the hydrological and ecological conditions allow infiltration, and provided there is adequate treatment of the contaminants to avoid a risk of soil and groundwater pollution. The aim of this study was to evaluate the feasibility of the application of a new technical infiltration system equipped with clinoptilolite as an artificial barrier material for the treatment of the copper roof runoff of the Academy of Fine Arts in Munich, Germany. During the 2-yr sampling period, 30 rain events were examined. The cover material of the roof and the drainage system was responsible for the high copper concentrations in the roof runoff. The rain height and the rain intensity were of great significance regarding the establishment of the copper runoff rate. The technical infiltration system applied was able to reduce the copper from the roof runoff by a factor up to 96%. The mean measured copper concentration in percolation water was lower than the critical value of 50 microg/l set by the German Federal Soil Protection Act and Ordinance, indicating no risk for soil and groundwater contamination.

  3. THE STUDY OF CLINOPTILOLITE MODIFIED WITH3d METALS HALIDES BY IR AND DIFFUSE REFLECTANCE SPECTROSCOPY

    Directory of Open Access Journals (Sweden)

    T. L. Rakitskaya

    2015-11-01

    Full Text Available The results of investigation of natural clinoptilolite (N-CLI and that modified with 3d metal halides (MeCl2/N-CLI, where Me are Cu, Co, and Mn by IR and diffuse reflectance spectroscopy are summarized. A band at 3437 cm-1 assigned to stretching vibrations of hydroxyl groups (nOH is found in the IR spectrum of the N-CLI sample. A location of the band was practically the same as for all above MeCl2/N-CLI samples. A band of middle intensity at 1638 cm-1 in the range of deformation vibrations of zeolite water observed in the IR spectrum of N-CLI slightly displays to lower frequencies in the case of the modified samples. An intensive wide band of a complex shape in the range from 1250 to 980 cm-1 assigned to Si–O–Si and Si–O–Al vibrations appears in IR spectra of all samples. A doublet band of middle intensity at 797 and 778 cm-1 is assigned to external symmetric stretching T-O vibrations and a band at 606 cm-1-to vibrations of a double ring. A location of the above bands is the same for all listed samples but their intensity is higher for MnCl2/N-CLI and CoCl2/N-CLI samples. After the reaction with ozone, significant changes in the IR spectra are observed only for MnCl2/N-CLI. They are due to MnO2 formation on the clinoptilolite surface resulting in a high frequency displacement of some bands. Based on UV-vi spectroscopy results, it is reasonable to make conclusions about the coordination and valence state of a central atom in the MeCl2/N-CLI samples under study. A location of charge transfer bands for these samples only slightly differs from that for N-CLI however the intensity of such bands increases for the MeCl2/N-CLI samples. The UV-vis spectrum of MnCl2/N-CLI changes after the reaction with ozone: the appearance of new bands of  charge transfer at 363 and 354 nm and also the two-fold increase in intensity of a charge transfer band at 272 nm in comparison with those of N-CLI and MnCl2/N-CLI are the evidence of change in both the

  4. Removal and recovery of p-phenylenediamines developing compounds from photofinishing lab-washwater using clinoptilolite tuffs from Greece.

    Science.gov (United States)

    Vlessidis, A G; Triantafillidis, C S; Evmiridis, N P

    2001-04-01

    Clinoptilolite tuffs from areas in Thrace region of Greece are compared with synthetic zeolites NaY and NH4Y for the uptake of N4-ethyl-N4-(2-methansulphonamidoethyl)-2-methyl-1,4-phenylenediamin (sesquisulphate, monohydrate) with the trade name CD-3 for the purpose to be used for clean-up and recycling photo-finishing and photo-developing washwaters. The cation-exchange capacity is found to be 6.15-11.1 mg/g for zeoliferous tuffs at equilibrium concentration of 50 ppm CD-3 in aqueous solution compared to 65.0 mg/g of NaY and 48.2 mg/g for NH4Y synthetic zeolites corresponding to the removal of CD-3 from 120 to 2001 of 50 ppm aqueous solution per kg of natural zeoliferous tuff; this capacity is only 6-10 times lower than type-Y synthetic zeolite. Initial rates of uptake are 20.8 mg/l/min for natural and 38.5 mg/l/min for synthetic zeolites. Regeneration levels of 55, 23, 35, and 33% are obtained for MCH, SF, NaY, and NH4Y, respectively. The rapid and almost complete uptake of CD-3 from its aqueous solutions at low CD-3 concentrations by the natural zeolites is promising for such an application.

  5. The spatial distribution and chemical heterogeneity of clinoptilolite at Yucca Mountain, Nye County, Nevada: Evidence for polygenetic hypogene alteration

    International Nuclear Information System (INIS)

    Livingston, D.E.; Szymanski, J.S.

    1994-01-01

    This part of TRAC's Annual Report for 1993 summarizes the finding of previous reports on the major element geochemistry of zeolitic alteration of the tuffs at Yucca Mountain and updates the status of work. In this report we examine the spatial distribution of zeolites by stratigraphic units and boreholes and the various types of chemical alteration of clinoptilolite indicated by the data reported in Broxton et al. and Bish and Chipera. The purpose is to evaluate the extent of the metasomatic alteration and to test the hypogene hypothesis of Szymanski. In this regard, it is of prime importance to evaluate whether the metasomatic alteration at Yucca Mountain is due to supergene or hypogene processes. In this report, the term open-quotes supergeneclose quotes denotes alteration and mineralization produced by fluids derived directly from atmospheric precipitation and infiltration through the vadose zone, and the term open-quotes hypogeneclose quotes denotes alteration and mineralization produced by fluids from the phreatic zone regardless of their former location or residence time in the Earth's crust. This report begins with a review of previous work on the genesis of zeolites of the Nevada Test Site

  6. Investigation of using Zeolite A and P synthesized from Iranian natural clinoptilolite for removal of heavy cations from simulated wastes

    International Nuclear Information System (INIS)

    Ghasemi Mbtaker, H.; Kazemiyan, H.; Maleki Nejad, A.; Zeinali, M. A. A.; Pakzad, M. R.

    2006-01-01

    Various methods have been used for the the removal o f heavy metal cations from mineral and industrial wastes. This research deals with the use of synthetic zeolites A and P synthesized from natural clinoptilolite for the removal process because of their superiority to ones. Ion exchange capacity of natural and synthetic samples was determined, then, the effects of some parameters such as temperature, time, and acidity on sorption were investigated as well as continues sorption. The sorption of lead cations was much better than that of other cations with the use of the synthetic samples and the rise in temperature and in pH has no significant effect. Sorption of this cations on the column was good. The results of cadmium sorption was promising and increasing the temperature increased the sorption and decreasing the pH decreased it. The sorption of zinc was rationally good; however it was less than previous cations, and increased with increasing the temperature. The results of nickel sorption in comparison with other cation, at high concentration was not promising. However, the results, at low concentration were good. Temperature had strong effect on nickel sorption

  7. Effect of the temperature on the sorption of cadmium in natural clinoptilolite from the State of Chihuahua; Efecto de la temperatura sobre la sorcion de cadmio en clinoptilolita natural del Estado de Chihuahua

    Energy Technology Data Exchange (ETDEWEB)

    Arambula V, V

    2004-07-01

    The investigation works related with the removal of cadmium of aqueous solutions, they make emphasis in a great number of materials that were used for this end, as well as in the parameters that influence, such as the temperature and the pH. In this work it was investigated the effect of the temperature on the removal of cadmium, using a zeolitic mineral native of the State of Chihuahua for they were determined it kinetic parameters, those diffusivity coefficients and the retention mechanisms (adsorption or ion exchange) involved. The clinoptilolite samples were characterized by means of scanning electron microscopy in high vacuum (MEB), elementary microanalysis (EDS) and X-ray diffraction (XRD). The experimental part consisted on putting in contact solutions of cadmium with the mineral, varying the temperature, the time of contact or the concentration; the quantification of sodium and cadmium in the liquid phase was carried out by means of atomic absorption spectroscopy (EAA). It was determined the time of equilibrium for the removal process. The temperature and the concentration influence on the process of sorption of cadmium in the zeolitic mineral (kinetics and isotherms). The kinetic model that describes better the sorption process of cadmium in the clinoptilolite was the pseudo-2 order. The apparent coefficient of diffusivity presented a greater value conforms to increment the temperature. The results of the isotherm of adsorption of cadmium presented a better adjustment to the Freundlich model. The quantity of cadmium retained by the mineral it was greater than the quantity of sodium found in the solution after the contact between the solution of cadmium and the zeolitic mineral and in accordance with the obtained separation factors, the natural zeolite shows a greater affinity for the cadmium that for the sodium ({alpha} > 1). (Author)

  8. Progress report on the kinetic measurements of the reactions of the silicates at the Yucca Mountain potential repository site. [Final] report, June 15, 1993--September 30, 1993

    International Nuclear Information System (INIS)

    Lasaga, A.C.; Ganor, J.

    1994-01-01

    Preliminary results are provided on: Synthesis and characterization of analcime and Na-clinoptilolite (Penn State), batch solubility experiments on analcime and clinoptilolite, thermodynamic modelling of solubility data, and kinetic flow-through experiments on analcime and clinoptilolite

  9. Integrated treatment process using a natural Wyoming clinoptilolite for remediating produced waters from coalbed natural gas operations

    Science.gov (United States)

    Zhao, H.; Vance, G.F.; Urynowicz, M.A.; Gregory, R.W.

    2009-01-01

    Coalbed natural gas (CBNG) development in western U.S. states has resulted in an increase in an essential energy resource, but has also resulted in environmental impacts and additional regulatory needs. A concern associated with CBNG development relates to the production of the copious quantities of potentially saline-sodic groundwater required to recover the natural gas, hereafter referred to as CBNG water. Management of CBNG water is a major environmental challenge because of its quantity and quality. In this study, a locally available Na-rich natural zeolite (clinoptilolite) from Wyoming (WY) was examined for its potential to treat CBNG water to remove Na+ and lower the sodium adsorption ratio (SAR, mmol1/2 L- 1/2). The zeolite material was Ca-modified before being used in column experiments. Column breakthrough studies indicated that a metric tonne (1000??kg) of Ca-WY-zeolite could be used to treat 60,000??L of CBNG water in order to lower SAR of the CBNG water from 30 to an acceptable level of 10??mmol1/2 L- 1/2. An integrated treatment process using Na-WY-zeolite for alternately treating hard water and CBNG water was also examined for its potential to treat problematic waters in the region. Based on the results of this study, use of WY-zeolite appears to be a cost-effective water treatment technology for maximizing the beneficial use of poor-quality CBNG water. Ongoing studies are evaluating water treatment techniques involving infiltration ponds lined with zeolite. ?? 2008 Elsevier B.V. All rights reserved.

  10. Hierarchical porous structured zeolite composite for removal of ionic contaminants from waste streams and effective encapsulation of hazardous waste

    Energy Technology Data Exchange (ETDEWEB)

    Al-Jubouri, Sama M. [Chemical Engineering & Analytical Science, The University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom); Curry, Nicholas A. [Materials Science, The University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom); Holmes, Stuart M., E-mail: stuart.holmes@manchester.ac.uk [Chemical Engineering & Analytical Science, The University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom)

    2016-12-15

    A hierarchical structured composite made from clinoptilolite supported on date stones carbon is synthesized using two techniques. The composites are manufactured by fixing a natural zeolite (clinoptilolite) to the porous surface of date stones carbon or by direct hydrothermal synthesis on to the surface to provide a supported high surface area ion-exchange material for metal ion removal from aqueous streams. The fixing of the clinoptilolite is achieved using sucrose and citric acid as a binder. The composites and pure clinoptilolite were compared to test the efficacy for the removal of Sr{sup 2+} ions from an aqueous phase. The encapsulation of the Sr{sup 2+} using either vitrification or a geo-polymer addition was tested to ensure that the hazardous waste can be made safe for disposal. The hierarchical structured composites were shown to achieve a higher ion exchange capacity per gram of zeolite than the pure clinoptilolite (65 mg/g for the pure natural clinoptilolite and 72 mg/g for the pure synthesized clinoptilolite) with the synthesized composite (160 mg/g) having higher capacity than the natural clinoptilolite composite (95 mg/g). The rate at which the equilibria were established followed the same trend showing the composite structure facilitates diffusion to the ion-exchange sites in the zeolite.

  11. Chemical variability of zeolites at a potential nuclear waste repository, Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Broxton, D.E.

    1985-01-01

    The compositions of clinoptilolites and their host tuffs have been examined by electron microprobe and x-ray fluorescence, respectively, to determine their variability at a potential nuclear waste repository, Yucca Mountain, Nevada. Because of their sorptive properties, these zeolites could provide important geologic barriers to radionuclide migration. Variations in clinoptilolite composition can strongly affect the mineral's thermal and ion-exchange properties, thus influencing its behavior in the repository environment. Clinoptilolites and heulandites closest to the proposed repository have calcium-rich compositions (60 to 90 mol. % Ca) and silica-to-aluminum ratios that concentrate between 4.0 and 4.6. In contrast, clinoptilolites and their host tuffs deeper in the volcanic sequence have highly variable compositions that vary vertically and laterally. Deeper-occurring clinoptilolites in the eastern part of Yucca Mountain are characterized by calcic-potassic compositions and tend to become more calcium-rich with depth. Clinoptilolites at equivalent stratigraphic levels on the western side of Yucca Mountain have sodic-potassic compositions and tend to become more sodium-rich with depth. Despite their differences in exchangeable cation compositions these two deeper-occurring compositional suites have similar silica-to-aluminum ratios, concentrating between 4.4 and 5.0. The chemical variability of clinoptilolites and their host tuffs at Yucca Mountain suggest that their physical and chemical properties will also vary. Compositionally-dependent clinoptilolite properties important for repository performance assessment include expansion/contraction behavior, hydration/dehydration behavior, and ion-exchange properties

  12. Removal of cadmium in urban wastewater with systems based on zeolite type clinoptilolite

    International Nuclear Information System (INIS)

    Barragan P, P.

    2016-01-01

    From an environmental issue detected in wastewater samples taken in a municipal wastewater collector in Nogales, Sonora, which is related to cadmium pollution, a research project came out where the principal aim was to implement a system to remove metallic ions of cadmium in wastewater, based on modified and unmodified natural zeolites. The zeolitic material used was natural clinoptilolite modified with NaCl and thiourea, sourced in El Cajon and Guaymas, Sonora. The materials were characterized with X-ray diffraction, Sem, Ft-IR spectra, and Bet analysis. The kinetics of four modified zeolites was investigated at ph=5 and initial concentration of 30 mgL"-"1 of Cd"2"+. The pseudo-first, the pseudo-second order, and Elovich models were applied to the experimental results. The results best fitted to pseudo-second order model. The maximum sorption capacity of modified zeolites was investigated through isotherms, The Langmuir model, Freundlich, and the combined Langmuir-Freundlich models were applied to the experimental results afterwards. ZGuayThio showed the highest sorption capacity, 11.60 mgg"-"1, with R"2=0.978 according to Langmuir-Freundlich model. Fixed-bed column adsorption experiments were carried out with ZGuayNa and ZGuayThio with three bed heights with 30 mgL"-"1 solution of Cd"2"+. influent at a flow rate of 1 mLmin"-"1, at ph=5. The Thomas, mass balance, and Bed Depth Service Time models were applied to the results. The dynamic adsorption capacity (No) and the constant of sorption velocity (K a) were determined, 28.67 gL"-"1 and 0.072 Lg"-"1min"-"1 respectively for ZGuayNa with R"2= 0.9954. Column experiments with municipal wastewater from Colinas del Yaqui sub-collector, previously characterized, were conducted using ZGuayNa and ZGuayThio. A mass transference model was applied to the results which accounted for K_p= 0.815 m"3Kg"-1 with R"2= 0.9789 for ZGuayNa, and K_p= 3.1 m"3Kg"-1 for ZGuayThio with R"2= 0.78. Finally, the capacity of the column system

  13. Effective removal of Ni(II) from aqueous solutions by modification of nano particles of clinoptilolite with dimethylglyoxime.

    Science.gov (United States)

    Nezamzadeh-Ejhieh, Alireza; Kabiri-Samani, Mehdi

    2013-09-15

    In this work an Iranian natural clinoptilolite tuff was pre-treated and changed to the micro (MCP) and nano (NCP) particles by mechanical method. Modification of micro and nano particles and also their Ni-exchanged forms were done by dimethylglyoxime (DMG). The raw and modified samples were characterized by XRD, FT-IR, SEM, BET, TG-DTG and energy dispersive analysis X-ray spectroscopy (EDAX). Removal of Ni(II) by modified and unmodified samples was investigated in batch procedure. It was found that NCP-DMG has higher capacity for removal of Ni(II). The effects of analytical parameters such as pH, dose of DMG, concentration of nickel solution, contact time and selectivity were studied and the optimal operation parameters were found as follows: pHPZC: 7.6, CNi(II): 0.01 M, contact time: 360 min and DMG dosage: 5mM. The results of selectivity experiments showed that the modified zeolite has a good selectivity for nickel in the presence of different multivalent cations. Langmuir and Freundlich isotherm models were adopted to describe the adsorption isotherms. Adsorption isotherms of Ni(II) ions could be best modelled by Langmuir equation, that indicate the monolayer sorption of Ni(II). Comparison of two kinetic models indicates that the adsorption kinetic can be well described by the pseudo-second-order rate equation that indicates that the rate limiting step for the process involves chemical reaction. The negative ΔH and ΔG indicate an exothermic and spontaneously process. The negative ΔS indicates that the adsorption of nickel cations from solution occurs with lower amount ion replacement, thus chemisorptions due to complex formation are dominant process in nickel removal. Copyright © 2013 Elsevier B.V. All rights reserved.

  14. Nano Fe{sub 2}O{sub 3,} clinoptilolite and H{sub 3}PW{sub 12}O{sub 40} as efficient catalysts for solvent-free synthesis of 5(4H)-isoxazolone under microwave irradiation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Fozooni, Samieh, E-mail: samieh.fozooni@uk.ac.ir, E-mail: s_fozooni@yahoo.com [Shahid Bahonar University, Kerman (Iran, Islamic Republic of). Mining Engineering Department. Zarand High Education Center; Hosseinzadeh, Nasrin Gholam; Akhgar, Mohammad Reza [Islamic Azad University, Kerman (Iran, Islamic Republic of). Department of Chemistry; Hamidian, Hooshang [Payame Noor University (PNU), Tehran (Iran, Islamic Republic of). Department of Chemistry

    2013-10-15

    A quick and solvent-free approach involving the exposure of neat reactants to microwave irradiation in conjunction with the use of clinoptilolite, H{sub 3}PW{sub 12}O{sub 40} and Fe{sub 2}O{sub 3} nanoparticle catalysts is described. In this work, condensation of hydroxylamine hydrochloride, sodium acetate, acetoacetic or benzoyl acetic ethyl ester and appropriate aldehydes by employing catalysts gave 5(4H)-isoxazolone only in one step. Catalyst amount, temperature effects and catalysts reusability were monitored. Among the catalysts, Fe{sub 2}O{sub 3} nanoparticles had better performance than other catalysts from viewpoint of yield and reaction time. The present protocol offers several advantages, such as short reaction time, reasonable yield, mild reaction condition and recycling catalysts with a very easy workup. (author)

  15. Sorption of cobalt in zeolites and natural clays of the clinoptilolite and kaolinite type; Sorcion de cobalto en zeolitas y arcillas naturales del tipo clinoptilolita y caolinita

    Energy Technology Data Exchange (ETDEWEB)

    Davila R, J.I.; Solache R, M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

    2006-07-01

    In this work the sorption of cobalt of aqueous solutions in two natural zeolites (clinoptilolite) and a clay (kaolinite) of origin in the center-north region of Mexico is evaluated. The effect of the pH and the time of contact in the process of sorption were evaluated. The cobalt retained in the aluminosilicates was determined by neutron activation analysis. The cobalt sorption in the materials in a range of pH from 4 to 7 does not present significant variations. The studies of reaction kinetics show a very fast sorption in the first 5 hours of contact, reaching the equilibrium in approximately 24 hours. The kinetics of sorption of the cobalt ions was represented better by the Ritchie reaction model modified of second order. The experimental data for the zeolites obtained at ambient temperature and varying the concentration were adjusted to the models of Freundlich, Langmuir and Freundlich-Langmuir isotherms and it was observed that the cobalt sorption it behaves according to the Freundlich isotherm model. (Author)

  16. Ageing and structural effects on the sorption characteristics of Cd2+ by clinoptilolite and Y-type zeolite studied using isotope exchange technique

    International Nuclear Information System (INIS)

    Ahmed, I.A.M.; Young, S.D.; Crout, N.M.J.

    2010-01-01

    This research investigates the long-term kinetics of Cd 2+ sorption and desorption by calcium-exchanged clinoptilolite (CaCpt) and Y-type (CaY) zeolite using isotopic exchange with 109 Cd while maintaining pH at circumneutral values. The effects of Si/Al ratio and crystal structure of these zeolitic materials on intracrystalline transport of Cd are discussed. A first-order kinetic model was developed to describe the progressive transfer of Cd 2+ to a less reactive form within the zeolite structure, following initial sorption and subsequent desorption of Cd subject to different initial contact times. The kinetic model differentiates between two forms of sorbed Cd 2+ designated 'labile' and 'non-labile' in which the labile form is in immediate equilibrium with the free Cd 2+ ion activity in solution. A model combining diffusion and first-order kinetics for cation exchange was also employed to determine Cd 2+ diffusivity and intracrystalline exchange rates in CaY and CaCpt. The efficiency of Permeable Reactive Barriers (PRBs) containing zeolitic materials in protecting water systems against lateral flow of metal-contaminated leachate was simulated for three contrasting zeolites. The slow transfer of Cd between labile and non-labile forms was particularly important in moderating high concentration pulses of Cd traversing the PRB. In addition, the reversibility of Cd fixation effectively restored the sorption capability of the zeolite through slow leakage to drainage water.

  17. Solid phase extraction-inductively coupled plasma spectrometry for adsorption of Co(II) and Ni(II) from radioactive wastewaters by natural and modified zeolites

    International Nuclear Information System (INIS)

    Akbar Malekpour; Mohammad Edrisi; Shamsollah Shirzadi; Saeed Hajialigol

    2011-01-01

    Natural and modified clinoptilolite as low-cost adsorbents have been used for adsorption of Co(II) and Ni(II) from nuclear wastewaters both in batch and continuous experiments. Zeolite X was also synthesized and its ability towards the selected cations was examined. Kinetic and thermodynamic behaviors for the process were investigated and adsorption equilibrium was interpreted in term of Langmuir and Freundlich equations. The effect of various parameters including the initial concentration, temperature, ionic strength and pH of solution were examined to achieve the optimized conditions. The clinoptilolite was shown good sorption potential for Co(II) and Ni(II) ions at pH values 4-6. Based on desorption studies, nearly 74 and 85% of adsorbed Co(II) and Ni(II) were removed from clinoptilolite by HCl. The Na + and NH 4 + forms of clinoptilolite were the best modified forms for the removal of investigated cations. It is concluded that the selectivity of clinoptilolite is higher for Co(II) than Ni(II). The synthesized zeolite showed more ability to remove cobalt and nickel ions from aqueous solution than the natural clinoptilolite. The microwave irradiation was found to be more rapid and effective for ion exchange compared to conventional ion exchange process. (author)

  18. The selective separation of Cs and Sr ion on the inorganic ion-exchanger zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Park, Hun Hwee; Min, Byeog Heon [Hoseo University, Taegu (Korea)

    1998-04-01

    This study shows the selective separation of Cs and Sr ion on the inorganic ion-exchanger zeolites such as clinoptilolite, Y-type CBV760, CBV780 and A-type 3A. The selective separation of Cs and Sr on these zeolites was examined using batch and continuous column experiments. For the selective separation of Cs and Sr from a synthetic wastewater, adsorption rate of Cs increased in the order, clinoptilolite> 3A>> CBV760> CBV780, adsorption rate of Sr increased in the other, 3A>> clinoptilolite> CBV760> CBV780. For the clinoptilolite, the adsorption rate of Cs reached about 96 {approx} 98% within 3h. The adsorption rate of Sr on 3A reached about 99% within 3h. (author). 40 refs., 27 figs., 4 tabs.

  19. Effects of mineralogy on sorption of strontium and cesium onto Calico Hills Tuff

    International Nuclear Information System (INIS)

    Meyer, R.E.; Arnold, W.D.; Case, F.I.; O'Kelley, G.D.; Land, J.F.

    1990-04-01

    The sorption properties of tuff formations at the proposed site for the high-level nuclear waste repository at Yucca Mountain, Nevada, have been extensively studied. Sorption and desorption measurements were made of strontium and cesium onto clinoptilolite and Calico Hills Tuff. The object was to see whether there was a correlation between sorption of strontium and cesium onto Calico Hills Tuff and the sorption of strontium and cesium onto clinoptilolite based on the content of clinoptilolite in the Calico Hills Tuff. 13 refs., 10 figs., 6 tabs

  20. The effect of feed supplementation with Zakarpacki zeolite (clinoptilolite) on percentages of T and B lymphocytes and cytokine concentrations in poultry.

    Science.gov (United States)

    Jarosz, Lukasz; Stepien-Pysniak, Dagmara; Gradzki, Zbigniew; Kapica, Malgorzata; Gacek, Agata

    2017-07-01

    The available literature lacks information on the effect of Zakarpacki zeolite (clinoptilolite) on the immune system of poultry. Therefore, the aim of this study was to determine the effect of this zeolite on selected indicators of the immune response in poultry by evaluating the expression of cluster of differentiation (CD) surface molecules on T and B lymphocytes and the concentration of IL-2 and IL-10 in the blood. Ninety one-day-old Ross 308 broiler chicks were used in the study. The birds were divided into 3 groups of 30 each. The same basic diet was used in all groups, but groups II and III received a feed additive in the form of 2% and 3% zeolite. Blood samples were collected from all birds on the 40th day of observations. Weight gain in the birds in both experimental groups was significantly higher, and no clinical symptoms of disease were observed. The percentage of CD4+CD25+ T and B lymphocytes was higher in both groups receiving zeolite, but the percentage of CD8+CD25+ T lymphocytes was higher only in the group receiving 3% zeolite. There were no differences between the groups in the percentage of cells with CD3+ and MHC Class II expression. Higher serum concentrations of IL-2 and IL-10 were noted only in group III. The use of zeolites enhances antigen presentation and leads to increased Th1 and Th2 response. Excessive supply of zeolite in the feed leads to a local inflammatory response, which may cause damage to the intestinal barrier. © 2017 Poultry Science Association Inc.

  1. Diagenesis of silica-rich mounded chalk, the Coniacian Arnager Limestone, Denmark

    DEFF Research Database (Denmark)

    Buus Madsen, Heine; Stemmerik, Lars; Surlyk, Finn

    2010-01-01

    The Coniacian Arnager Limestone Formation is exposed on the Danish island of Bornholm in the Baltic Sea. It is composed of mound-bedded siliceous chalk, and X-ray diffraction and scanning electron microscopy indicate a content of 30-70% insoluble minerals, including authigenic opal-CT, quartz......, clinoptilolite, feldspars, calcite, dolomite, and barite. Opal-CT and clinoptilolite are the most common and constitute 16-53% and 2-9%, respectively. The content of insoluble minerals varies laterally bothwithinthemounds and inplanar beds, and the opal-CT content varies by up to 10% vertically. Themounds...... precipitation of opal-CT. The opal-CT formed at temperatures around 17°C, the precipitation lowered the silica activity and the Si/Al ratio of the pore water, resulting in precipitation of clinoptilolite, feldspar and smectite. Calcite formed synchronouslywith the latest clinoptilolite.Minoramounts of quartz...

  2. Immobilization of radioactive waste in cement based matrices

    International Nuclear Information System (INIS)

    Glasser, F.P.; Rahman, A.A.; Macphee, D.; McCulloch, C.E.; Angus, M.J.

    1985-06-01

    The kinetics of reaction between cement and clinoptilolite are elucidated and rate equations containing temperature dependent constants derived for this reaction. Variations in clinoptilolite particle size and their consequences to reactivity are assessed. The presence of pozzolanic agents more reactive than clinoptilolite provides sacrificial agents which are partially effective in lowering the clinoptilolite reactivity. Blast furnace slag-cements have been evaluated and the background literature summarized. Experimental studies of the pore fluid in matured slag-cements show that they provide significantly more immobilization for Cs than Portland cement. The distribution of Sr in cemented waste forms has been examined, and it is shown that most of the chemical immobilization potential in the short term is likely to be associated with the aluminate phases. The chemical and structural nature of these are described. Carbonation studies on real cements are summarized. (author)

  3. Modeling fluid-rock interaction at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Viani, B.E.; Bruton, C.J.

    1992-08-01

    Volcanic rocks at Yucca Mountain, Nevada aie being assessed for their suitability as a potential repository for high-level nuclear waste. Recent progress in modeling fluid-rock interactions, in particular the mineralogical and chemical changes that may accompany waste disposal at Yucca Mountain, will be reviewed in this publication. In Part 1 of this publication, ''Geochemical Modeling of Clinoptilolite-Water Interactions,'' solid-solution and cation-exchange models for the zeolite clinoptilolite are developed and compared to experimental and field observations. At Yucca Mountain, clinoptilolite which is found lining fractures and as a major component of zeolitized tuffs, is expected to play an important role in sequestering radionuclides that may escape from a potential nuclear waste repository. The solid-solution and ion-exchange models were evaluated by comparing predicted stabilities and exchangeable cation distributions of clinoptilolites with: (1) published binary exchange data; (2) compositions of coexisting clinoptilolites and formation waters at Yucca Mountain; (3) experimental sorption isotherms of Cs and Sr on zeolitized tuff, and (4) high temperature experimental data. Good agreement was found between predictions and expertmental data, especially for binary exchange and Cs and Sr sorption on clinoptilolite. Part 2 of this publication, ''Geochemical Simulation of Fluid-Rock Interactions at Yucca Mountain,'' describes preliminary numerical simulations of fluid-rock interactions at Yucca Mountain. The solid-solution model developed in the first part of the paper is used to evaluate the stability and composition of clinciptilolite and other minerals in the host rock under ambient conditions and after waste emplacement

  4. A Novel Desulfurizer-Catalyst Combination for Logistic Fuel Reforming

    Science.gov (United States)

    2009-04-27

    the sulfur capture propensity of these formu- Figure 1. SEM images of clinoptilolite (left) and diatomite (right) support matrix. Figure 2. Sulfur...stainless steel foils to enhance the surface area. The time dependence of sulfur capture by the clinoptilolite-based (C-series) and diatomite -based (D

  5. Radionuclide sorption in Yucca Mountain tuffs with J-13 well water: Neptunium, uranium, and plutonium. Yucca Mountain site characterization program milestone 3338

    International Nuclear Information System (INIS)

    Triay, I.R.; Cotter, C.R.; Kraus, S.M.; Huddleston, M.H.

    1996-08-01

    We studied the retardation of actinides (neptunium, uranium, and plutonium) by sorption as a function of radionuclide concentration in water from Well J-13 and of tuffs from Yucca Mountain. Three major tuff types were examined: devitrified, vitric, and zeolitic. To identify the sorbing minerals in the tuffs, we conducted batch sorption experiments with pure mineral separates. These experiments were performed with water from Well J-13 (a sodium bicarbonate groundwater) under oxidizing conditions in the pH range from 7 to 8.5. The results indicate that all actinides studied sorb strongly to synthetic hematite and also that Np(V) and U(VI) do not sorb appreciably to devitrified or vitric tuffs, albite, or quartz. The sorption of neptunium onto clinoptilolite-rich tuffs and pure clinoptilolite can be fitted with a sorption distribution coefficient in the concentration range from 1 X 10 -7 to 3 X 10 -5 M. The sorption of uranium onto clinoptilolite-rich tuffs and pure clinoptilolite is not linear in the concentration range from 8 X 10 -8 to 1 X 10 -4 M, and it can be fitted with nonlinear isotherm models (such as the Langmuir or the Freundlich Isotherms). The sorption of neptunium and uranium onto clinoptilolite in J-13 well water increases with decreasing pH in the range from 7 to 8.5. The sorption of plutonium (initially in the Pu(V) oxidation state) onto tuffs and pure mineral separates in J-13 well water at pH 7 is significant. Plutonium sorption decreases as a function of tuff type in the order: zeolitic > vitric > devitrified; and as a function of mineralogy in the order: hematite > clinoptilolite > albite > quartz

  6. A method for removing sulfur bearing compounds from paraffinous hydrocarbons or a directly distilled benzine fraction

    Energy Technology Data Exchange (ETDEWEB)

    Konyukhova, T.P.; Bolotskaya, I.A.; Mikhaylova, L.A.; Sadykov, A.N.; Shitovkin, N.T.; Vlasov, V.V.

    1983-01-01

    In the known method for removing sulfurorganic compounds from paraffinous hydrocarbons or a directly distilled gasoline fraction through their adsorption using natural zeolite, in order to increase the degree of purification, clinoptilolite (Kp), which contains SiO2 and A12O3 in a molar ratio of 10.6 to 16.7 is used as the natural zeolite. The purification of the paraffinous hydrocarbons through clinoptilolite adsorption as compared with mordenite adsorption makes it possible to increase the degree of their purification of ethylmercaptane and dimethylsulfide. The effectiveness of clinoptilolite is also confirmed in removing mercaptanes and sulfides from directly distilled gasoline fractions.

  7. Impact of medicated feed along with clay mineral supplementation on Escherichia coli resistance to antimicrobial agents in pigs after weaning in field conditions.

    Science.gov (United States)

    Jahanbakhsh, Seyedehameneh; Kabore, Kiswendsida Paul; Fravalo, Philippe; Letellier, Ann; Fairbrother, John Morris

    2015-10-01

    The aim of this study was to examine changes in antimicrobial resistance (AMR) phenotype and virulence and AMR gene profiles in Escherichia coli from pigs receiving in-feed antimicrobial medication following weaning and the effect of feed supplementation with a clay mineral, clinoptilolite, on this dynamic. Eighty E. coli strains isolated from fecal samples of pigs receiving a diet containing chlortetracycline and penicillin, with or without 2% clinoptilolite, were examined for antimicrobial resistance to 15 antimicrobial agents. Overall, an increased resistance to 10 antimicrobials was observed with time. Supplementation with clinoptilolite was associated with an early increase but later decrease in blaCMY-2, in isolates, as shown by DNA probe. Concurrently, a later increase in the frequency of blaCMY-2 and the virulence genes iucD and tsh was observed in the control pig isolates, being significantly greater than in the supplemented pigs at day 28. Our results suggest that, in the long term, supplementation with clinoptilolite could decrease the prevalence of E. coli carrying certain antimicrobial resistance and virulence genes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Kinetic measurements on the silicates of the Yucca Mountain potential repository. Final report for October 1994--September 1995

    International Nuclear Information System (INIS)

    Barnes, H.L.; Wilkin, R.T.

    1995-08-01

    This Final Report includes a summary and discussion of results obtained under this project on the solubilities in subcritical aqueous solutions of Mont St. Hilaire analcime, Wikieup analcime, and Castle Creek Na-clinoptilolite. Also included here are the methods and results of hydrothermal flow-through experiments designed to measure the rates of Na-clinoptilolite dissolution and precipitation at 125 degree C. In this report, high-temperature solubility measurements made in our lab are integrated and discussed along with the low-temperature measurements made at Yale University. The final report prepared by the group at Yale University (Lasaga et al.) includes a synthesis of dissolution rate measurements made between 25 degree and 125 degree C on the Na-clinoptilolite

  9. The Usage of Natural Zeolites for the Adsorption of Radionuclides, particularly in emergency situations

    International Nuclear Information System (INIS)

    Reitbauer, Franz

    2012-09-01

    Specific natural zeolites have proven their capability to bind nuclear radiation During the last decades, numerous research work has proven the potential of natural zeolites to adsorb nuclear radiation through their cation exchange properties. Zeolites have been used successfully in Chernobyl, and are used in Fukushima and in nuclear waste repositories today. Within the various kinds of zeolites the special type clinoptilolite particularly binds 137-cesium as well as 90- strontium ions. Therefore zeolites with high contents of clinoptilolite are the first choice for this purpose. High contents of clinoptilolite can be defined as being above 90 %. Such zeolites are typically capable of binding some 2,50 meq/g of cesium ions and some 1,40 meq/g of strontium ions. (authors)

  10. A study of the properties of hexacyanoferrate sorbents and their use for sorption of caesium and strontium

    International Nuclear Information System (INIS)

    Kareta, V.I.; Grivkova, A.I.; Artemova, T.N.; Mizina, L.I.; Krasavina, E.P.

    1997-01-01

    A method of deposition of zinc, copper, and nickel hexacyanaferrates on silica-containing substrate (clinoptilolite) has been developed to produce mechanically strong sorbents for cesium and strontium separation from solutions of different compositions. The modification of clinoptilolite increases its sorption capacity for both cesium and strontium. Sorption behaviour of radionuclides was studied both in static and kinetic conditions. (author). 21 refs, 5 figs, 7 tabs

  11. Hydrogen Adsorption in Zeolite Studied with Sievert and Thermogravimetric Methods

    International Nuclear Information System (INIS)

    Lesnicenoks, P; Sivars, A; Grinberga, L; Kleperis, J

    2012-01-01

    Natural clinoptilolite (mixture from clinoptilolite, quartz and muscovite) is activated with palladium and tested for hydrogen adsorption capability at temperatures RT - 200°C. Thermogravimetric and volumetric methods showed that zeolite activated with palladium (1.25%wt) shows markedly high hydrogen adsorption capacity - up to 3 wt%. Lower amount of adsorbed hydrogen (∼1.5 wt%) was found for raw zeolite and activated with higher amount of palladium sample. Hypothesis is proposed that the heating of zeolite in argon atmosphere forms and activates the pore structure in zeolite material, where hydrogen encapsulation (trapping) is believed to occur when cooling down to room temperature. An effect of catalyst (Pd) on hydrogen sorption capability is explained by spillover phenomena were less-porous fractions of natural clinoptilolite sample (quartz and muscovite) are involved.

  12. Preparation for kinetic measurements on the silicates of the Yucca Mountain potential repository. [Final report], June 15, 1993--September 30, 1993

    International Nuclear Information System (INIS)

    1993-01-01

    Part 1, ''The Preparation of Clinoptilolite, Mordenite and Analcime,'' summarized progress made during the contract period on preparing Na-end member clinoptilolite, mordenite, and analcime. The objective is to use the prepared zeolites to determine rates of dissolution and precipitation in laboratory flow-through systems in both this lab to 350 C and by the geochemists at Yale University to about 80 C. Because clinoptilolite represents the most complicated phase of these three zeolites and it is most abundant at Yucca Mountain, the authors have concentrated most of their efforts on its preparation. They have collected, high-concentration natural clinoptilolite samples. A hindered settling technique that takes advantage of the relatively low specific gravity of clinoptilolite coupled with ultrasonic cleaning in deionized water has been employed. This material is now a mixed Na-K zeolite which must then be converted to the pure Na-end member composition. In Part 2, ''Draft Manuscript on the Heterogeneous Kinetics of Cristobalite,'' experiments on the rates of reactions of dissolution and precipitation of cristobalite were carried at 150--300 C. Results show that cristobalite may precipitate from hydrothermal solution if the concentration of Si(OH) 4 exceeds that at quartz saturation and is less than that of amorphous silica saturation and if there are cristobalite nuclei present. Such nuclei may occur where there has been devitrification of volcanic glasses, for example. Cristobalite has refused to crystallize in the absence of such nuclei. Steady state concentrations were reached experimentally after starting at 150 degree with initially supersaturated solutions and at 200 C starting with either supersaturated or undersaturated solutions. From the steady state conditions, equilibrium constants can be derived

  13. Zeolite: "the magic stone: main nutritional, environmental, experimental and clinical fields of application

    OpenAIRE

    Laurino, Carmen; Palmieri, Beniamino

    2015-01-01

    Introduction: zeolites (clinoptilolites) are a family of alluminosilicates and cations clustered to form macro aggregates by small individual cavities. In the medical area they are involved in detoxification mechanisms capturing ions and molecules into their holes. Actually, we classify about 140 types of natural and 150 synthetic zeolites, for specific and selective use. Clinoptilolite is a natural zeolite and it is the most widespread compound in the medical market. Objective: this review a...

  14. Characterization of Mexican zeolite minerals; Caracterizacion de minerales zeoliticos mexicanos

    Energy Technology Data Exchange (ETDEWEB)

    Jimenez C, M.J

    2005-07-01

    50% of the Mexican territory is formed by volcanic sequences of the Pliocene type, which appear extensively in the northwest states (Sonora, Sinaloa, Chihuahua, Durango) and west of Mexico (Jalisco and Nayarit), in central Mexico (Zacatecas, Guanajuato, San Luis Potosi, Queretaro, Hidalgo) and south of Mexico (Guerrero, Oaxaca); therefore, it is to be expected that in our country big locations of natural zeolites exist in its majority of the clinoptilolite type. The present study was focused toward the characterization of two Mexican natural zeolite rocks presumably of the clinoptilolite and filipsite types, one of them comes from the state of Chihuahua and the other of a trader company of non metallic minerals, due that these materials are not characterized, its are not known their properties completely and therefore, the uses that can be given to these materials. In this investigation work it was carried out the characterization of two Mexican zeolite rocks, one coming from the Arroyo zone, municipality of La Haciendita, in the state of Chihuahua; and the other one was bought to a trader company of non metallic minerals. The two zeolites so much in their natural form as conditioned with sodium; they were characterized by means of X-ray diffraction, scanning electron microscopy of high vacuum and elementary microanalysis (EDS), surface area analysis (BET), thermal gravimetric analysis. To differentiate the heulandite crystalline phase of the other clinoptilolite rock, its were carried out thermal treatments. The quantification of Al, Na, Ca, K, Mg, Fe was carried out in solution, by means of atomic absorption spectroscopy and the quantity of Si was determined by gravimetry. The zeolite rocks presented for the major part the crystalline heulandite and clinoptilolite phases for the most part, and it was found that the zeolite coming from the state of Chihuahua possesses a bigger content of heulandite and the denominated filipsite it is really a zeolite

  15. Characterization of Mexican zeolite minerals

    International Nuclear Information System (INIS)

    Jimenez C, M.J.

    2005-01-01

    50% of the Mexican territory is formed by volcanic sequences of the Pliocene type, which appear extensively in the northwest states (Sonora, Sinaloa, Chihuahua, Durango) and west of Mexico (Jalisco and Nayarit), in central Mexico (Zacatecas, Guanajuato, San Luis Potosi, Queretaro, Hidalgo) and south of Mexico (Guerrero, Oaxaca); therefore, it is to be expected that in our country big locations of natural zeolites exist in its majority of the clinoptilolite type. The present study was focused toward the characterization of two Mexican natural zeolite rocks presumably of the clinoptilolite and filipsite types, one of them comes from the state of Chihuahua and the other of a trader company of non metallic minerals, due that these materials are not characterized, its are not known their properties completely and therefore, the uses that can be given to these materials. In this investigation work it was carried out the characterization of two Mexican zeolite rocks, one coming from the Arroyo zone, municipality of La Haciendita, in the state of Chihuahua; and the other one was bought to a trader company of non metallic minerals. The two zeolites so much in their natural form as conditioned with sodium; they were characterized by means of X-ray diffraction, scanning electron microscopy of high vacuum and elementary microanalysis (EDS), surface area analysis (BET), thermal gravimetric analysis. To differentiate the heulandite crystalline phase of the other clinoptilolite rock, its were carried out thermal treatments. The quantification of Al, Na, Ca, K, Mg, Fe was carried out in solution, by means of atomic absorption spectroscopy and the quantity of Si was determined by gravimetry. The zeolite rocks presented for the major part the crystalline heulandite and clinoptilolite phases for the most part, and it was found that the zeolite coming from the state of Chihuahua possesses a bigger content of heulandite and the denominated filipsite it is really a zeolite

  16. The effect of the synthesis method on the parameters of pore structure and selectivity of ferrocyanide sorbents based on natural minerals

    International Nuclear Information System (INIS)

    Voronina, A.V.; Gorbunova, T.V.; Semenishchev, V.S.

    2017-01-01

    Ferrocyanide sorbents were obtained via thin-layer and surface modification of natural clinoptilolite and marl. The effect of modification method on surface characteristics of these sorbents and their selectivity for cesium was studied. It was shown that the modification resulted in an increase of selectivity of modified ferrocyanide sorbents to cesium as compared with the natural clinoptilolite in presence of Na + , as well as in an increase of cesium distribution coefficients in presence of K + . The nickel-potassium ferrocyanide based on the clinoptilolite showed the highest selectivity for cesium at sodium concentrations of 10 -4 -2 mol L -1 : cesium distribution coefficient was lg K d = 4.5 ± 0.4 L kg -1 and cesium/sodium separation factor was α(Cs/Na) = 250. In the presence of NH 4 + , all modified sorbents showed approximately equal selectivity for 137 Cs. Probable applications of the sorbents were suggested. (author)

  17. ZEOLITE: "THE MAGIC STONE"; MAIN NUTRITIONAL, ENVIRONMENTAL, EXPERIMENTAL AND CLINICAL FIELDS OF APPLICATION.

    Science.gov (United States)

    Laurino, Carmen; Palmieri, Beniamino

    2015-08-01

    zeolites (clinoptilolites) are a family of alluminosilicates and cations clustered to form macro aggregates by small individual cavities. In the medical area they are involved in detoxification mechanisms capturing ions and molecules into their holes. Actually, we classify about 140 types of natural and 150 synthetic zeolites, for specific and selective use. Clinoptilolite is a natural zeolite and it is the most widespread compound in the medical market. this review analyzes the main fields of zeolite utilization. we searched Pubmed/Medline using the terms "zeolite" and "clinoptilolite". in zoothechnology and veterinary medicine zeolite improves the pets' fitness, removes radioactive elements, aflatoxines and poisons. Zeolite displays also antioxidant, whitening, hemostatic and anti-diarrhoic properties, projected in human care. However very scanty clinical studies have been run up to now in immunodeficiency, oncology after chemotherapy and radiotherapy as adjuvants. further clinical investigations are urgently required after this review article publication which updates the state of the art. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

  18. Natural sorbents as barriers against migration of radionuclides from radioactive waste repositories

    International Nuclear Information System (INIS)

    Stefanova, I.; Gradev, G.D.

    1993-01-01

    The sorption properties of Bulgarian inorganic sorbents - clinoptilolite, vermiculite, bentonite, glauconite, celadonite and loess, which can be used as buffer, backfill and sealing materials in radwaste repository are studied. Experimental data about sorption and desorption capacities, radiation and thermal stability of sorbents from different Bulgarian deposits are reported and compared. Clinoptilolite from Beli Plast and its sodium variety from Kostino and Moryantsi is recommended as a barrier against radionuclide migration from radwaste repository due to their high sorption capacity of 137 Ce, 90 Sr and 60 Co. The high selectivity of vermiculite for polyvalent ions ( 144 Ce, 59 Fe and 90 Sr) gives grounds to include the sorption on vermiculite as a second step in the ion exchange technology for low level laundry waste decontamination. Bentonite is studied as a proposed buffer, backfill and sealing material. Its selectivity for cesium is lower compared to those of clinoptilolite. Thus a tailored-made mixture of bentonite and clinoptilolite will act as a barrier against radionuclides in different oxidation state. Glauconite can be successfully used as a barrier against migration of 144 Ce, 90 Sr, 54 Mn and 65 Zn. Loess is also included in the study, as the Kozloduy NPP is sited on loess formation and it is a natural potential site for low and intermediate level waste burial. It is concludes that zeolites and clays of Bulgarian deposits can be used effectively against radionuclide migration from radioactive waste repositories. 59 refs., 5 tabs. (author)

  19. Engineered biochar from microwave-assisted catalytic pyrolysis of switchgrass for increasing water-holding capacity and fertility of sandy soil

    International Nuclear Information System (INIS)

    Mohamed, Badr A.; Ellis, Naoko; Kim, Chang Soo; Bi, Xiaotao; Emam, Ahmed El-raie

    2016-01-01

    Engineered biochars produced from microwave-assisted catalytic pyrolysis of switchgrass have been evaluated in terms of their ability on improving water holding capacity (WHC), cation exchange capacity (CEC) and fertility of loamy sand soil. The addition of K 3 PO 4 , clinoptilolite and/or bentonite as catalysts during the pyrolysis process increased biochar surface area and plant nutrient contents. Adding biochar produced with 10 wt.% K 3 PO 4 + 10 wt.% clinoptilolite as catalysts to the soil at 2 wt% load increased soil WHC by 98% and 57% compared to the treatments without biochar (control) and with 10 wt.% clinoptilolite, respectively. Synergistic effects on increased soil WHC were manifested for biochars produced from combinations of two additives compared to single additive, which may be the result of increased biochar microporosity due to increased microwave heating rate. Biochar produced from microwave catalytic pyrolysis was more efficient in increasing the soil WHC due to its high porosity in comparison with the biochar produced from conventional pyrolysis at the same conditions. The increases in soil CEC varied widely compared to the control soil, ranging from 17 to 220% for the treatments with biochars produced with 10 wt% clinoptilolite at 400 °C, and 30 wt% K 3 PO 4 at 300 °C, respectively. Strong positive correlations also exist among soil WHC with CEC and biochar micropore area. Biochar from microwave-assisted catalytic pyrolysis appears to be a novel approach for producing biochar with high sorption affinity and high CEC. These catalysts remaining in the biochar product would provide essential nutrients for the growth of bioenergy and food crops. - Highlights: • High quality biochar was made by catalytic pyrolysis in a microwave reactor. • High heating rate and good biochar quality were achieved using K 3 PO 4 and clinoptilolite mixture. • Biochars showed significant increase in soil WHC and CEC. • Microwave catalytic pyrolysis can produce

  20. Engineered biochar from microwave-assisted catalytic pyrolysis of switchgrass for increasing water-holding capacity and fertility of sandy soil

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed, Badr A. [Department of Chemical and Biological Engineering, University of British Columbia, Vancouver BC V6T 1Z3 (Canada); Agricultural Engineering Department, Cairo University, Giza (Egypt); Ellis, Naoko [Department of Chemical and Biological Engineering, University of British Columbia, Vancouver BC V6T 1Z3 (Canada); Kim, Chang Soo [Department of Chemical and Biological Engineering, University of British Columbia, Vancouver BC V6T 1Z3 (Canada); Clean Energy Research Center, Korea Institute of Science and Technology, 14 gil 5 Hwarang-no Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Bi, Xiaotao, E-mail: tony.bi@ubc.ca [Department of Chemical and Biological Engineering, University of British Columbia, Vancouver BC V6T 1Z3 (Canada); Emam, Ahmed El-raie [Agricultural Engineering Department, Cairo University, Giza (Egypt)

    2016-10-01

    Engineered biochars produced from microwave-assisted catalytic pyrolysis of switchgrass have been evaluated in terms of their ability on improving water holding capacity (WHC), cation exchange capacity (CEC) and fertility of loamy sand soil. The addition of K{sub 3}PO{sub 4}, clinoptilolite and/or bentonite as catalysts during the pyrolysis process increased biochar surface area and plant nutrient contents. Adding biochar produced with 10 wt.% K{sub 3}PO{sub 4} + 10 wt.% clinoptilolite as catalysts to the soil at 2 wt% load increased soil WHC by 98% and 57% compared to the treatments without biochar (control) and with 10 wt.% clinoptilolite, respectively. Synergistic effects on increased soil WHC were manifested for biochars produced from combinations of two additives compared to single additive, which may be the result of increased biochar microporosity due to increased microwave heating rate. Biochar produced from microwave catalytic pyrolysis was more efficient in increasing the soil WHC due to its high porosity in comparison with the biochar produced from conventional pyrolysis at the same conditions. The increases in soil CEC varied widely compared to the control soil, ranging from 17 to 220% for the treatments with biochars produced with 10 wt% clinoptilolite at 400 °C, and 30 wt% K{sub 3}PO{sub 4} at 300 °C, respectively. Strong positive correlations also exist among soil WHC with CEC and biochar micropore area. Biochar from microwave-assisted catalytic pyrolysis appears to be a novel approach for producing biochar with high sorption affinity and high CEC. These catalysts remaining in the biochar product would provide essential nutrients for the growth of bioenergy and food crops. - Highlights: • High quality biochar was made by catalytic pyrolysis in a microwave reactor. • High heating rate and good biochar quality were achieved using K{sub 3}PO{sub 4} and clinoptilolite mixture. • Biochars showed significant increase in soil WHC and CEC.

  1. Barriers to migration of radionuclides from radioactive waste repositories

    International Nuclear Information System (INIS)

    Stefanova, I.

    1999-01-01

    Natural inorganic sorbents are known as effective barriers that reduce the migration of radionuclides from radioactive waste repositories and contaminated sites. They could be used as buffer, backfill and sealing materials in the repository and their presence in the host rock and the surrounding geological formations increases the retention properties of the strata. Natural occurring minerals from local origin are used in the study - zeolites (clinoptilolite and mordenite), celadonite and loess. Sorption of wide range of radionuclides is studies. Batch capacity is determined. Sorption of radionuclides from simulated natural solution is studied. Distribution coefficients are calculated from sorption isotherms. Desorption in presence of different natural solutions is studied. Sorption properties are compared. It is shown that clinoptilolite acts as effective barrier against migration of radionuclides from repositories. The presence of celadonite in the clinoptilolite rock increases the retention of polyvalent ions. The retention of radionuclides on loess samples fulfils the requirements for host media for repository for low and intermediate level waste. A method for construction of additional barrier to the existing in the country disposal vault for spent sealed sources is proposed

  2. Leaching behaviour and mechanical properties of copper flotation waste in stabilized/solidified products.

    Science.gov (United States)

    Mesci, Başak; Coruh, Semra; Ergun, Osman Nuri

    2009-02-01

    This research describes the investigation of a cement-based solidification/stabilization process for the safe disposal of copper flotation waste and the effect on cement properties of the addition of copper flotation waste (CW) and clinoptilolite (C). In addition to the reference mixture, 17 different mixtures were prepared using different proportions of CW and C. Physical properties such as setting time, specific surface area and compressive strength were determined and compared to a reference mixture and Turkish standards (TS). Different mixtures with the copper flotation waste portion ranging from 2.5 to 12.5% by weight of the mixture were tested for copper leachability. The results show that as cement replacement materials especially clinoptilolite had clear effects on the mechanical properties. Substitution of 5% copper flotation waste for Portland cement gave a similar strength performance to the reference mixture. Higher copper flotation waste addition such as 12.5% replacement yielded lower strength values. As a result, copper flotation waste and clinoptilolite can be used as cementitious materials, and copper flotation waste also can be safely stabilized/solidified in a cement-based solidification/stabilization system.

  3. Strontium binding to cement paste cured at different temperature

    International Nuclear Information System (INIS)

    Peterson, V.K.; Ray, A.

    1999-01-01

    Concentration - depth profiles were measured using Proton Induced X-ray Emission (PIXE). These results were used as a measure of the Sr 2+ retention abilities of each matrix. Ordinary Portland cement (OPC) and cemented clinoptilolite samples were cured at 25 deg C, 60 deg C and 150 deg C. As expected, the Sr 2+ penetration depth increased with increasing OPC cure temperature, caused by an increase in sample permeability. Surprisingly, the penetration depths of Sr 2+ increased with the addition of clinoptilolite to the OPC, also thought to be caused by an increase in sample permeability. However, the increase in penetration depth was reduced in samples cured at higher temperatures

  4. Zeolites modified with silver for the development of a water disinfection system

    International Nuclear Information System (INIS)

    Aparicio V, S.

    2013-01-01

    In spite of great strides that have been taken in sanitation technologies, there still exist health problems due to microbiological contamination by water. The waterborne diseases have not been completely eradicated and are a big problem of economic interest and health. Moreover, the microbicidal properties of silver have been used for a long time. The use of silver as a disinfectant has many advantages; for example it inhibits a wide spectrum of microorganisms, it has oligo dynamic properties and owing its mechanisms of cell inactivation, it also does not allow the emergence of new resistant strains. In the present research, the kinetics of water disinfection with silver has been investigated, to develop small system for water disinfection, based in silver modified Mexican clinoptilolite. The chemical species of silver play a significant role in the disinfection processes. For this reason, in this work, were both the Ag + and nanoparticles of Ag ο considered. The synthesis of nanoparticles of Ag ο woes performed by thermal and chemical reduction. It was found that the chemical reduction of Ag + to Ag ο was more efficient because it presented more defined nano structures and better distribution than those of thermal reduction. Clinoptilolite of Taxco (Guerrero) was chosen to exchange the native ions from the clinoptilolite by Ag + from the aqueous medium, or to deposit the nanoparticles of Ag ο on this surface. These silver modified zeolitic materials were characterized by scanning electron microscopy (Sem), elemental analyses (EDS), X-ray diffraction (XRD) and neutron activation analysis (NAA). The results showed that the crystallographic structure of the clinoptilolite did not change during thermal and chemical reduction treatments of Ag + to obtain the nanoparticles of Ag ο . The bactericide activity of the silver modified zeolitic materials (with Ag + or nanoparticles of Ag ο ) was evaluated on Escherichia coli Atcc 8739, in both distilled water and well

  5. Calcium Solubility and Cation Exchange Properties in Zeoponic Soil

    Science.gov (United States)

    Beiersdorfer, Raymond E.

    1999-01-01

    An important aspect of a regenerative life support system at a Lunar or Martian outpost is the ability to produce food. Essential plant nutrients, as well as a solid support substrate, can be provided by: (1) treated Lunar or Martian regolith; (2) a synthetic soil or (3) some combination of both. A synthetic soil composed of ammonium- and potassium-saturated chinoptlolite (a zeolite mineral) and apatite, can provide slow-release fertilization of plants via dissolution and ion-exchange reactions. Previous equilibrium studies (Beiersdorfer, 1997) on mixtures of synthetic hydroxyapatite and saturated-clinoptilolite indicate that the concentrations of macro-nutrients such as ammonium, phosphorous, potassium, magnesium, and calcium are a function of the ratio of chinoptilolite to apatite in the sample and to the ratio of potassium to ammonium on the exchange sites in the clinoptilolite. Potassium, ammonium, phosphorous, and magnesium are available to plants at sufficient levels. However, calcium is deficient, due to the high degree of calcium adsorption by the clinoptilolite. Based on a series of batch-equilibration experiments, this calcium deficiency can be reduced by (1) treating the clinoptilolite with CaNO3 or (2) adding a second Ca-bearing mineral (calcite, dolomite or wollastonite) to the soil. Treating the Cp with CaNO3 results in increased Ca in solution, decreased P in solution and decreased NH4 in solution. Concentrations of K were not effected by the CaNO3 treatment. Additions of Cal, Dol and Wol changed the concentrations of Ca and P in solution in a systematic fashion. Cal has the greatest effect, Dol the least and Wol is intermediate. The changes are consistent with changes expected for a common ion effect with Ca. Higher concentrations of Ca in solution with added Cal, Dol or Wol do not result in changes in K or NH4 concentrations.

  6. Mineralogic Zonation Within the Tuff Confining Unit, Yucca Flat, Nevada Test Site

    International Nuclear Information System (INIS)

    Lance Prothro

    2005-01-01

    Recently acquired mineralogic data from drill hole samples in Yucca Flat show that the tuff confining unit (TCU) can be subdivided into three mineralogic zones based on the relative abundances of primary and secondary mineral assemblages. These zones are (1) an upper zone characterized by the abundance of the zeolite mineral clinoptilolite with lesser amounts of felsic and clay minerals; (2) a middle zone with felsic minerals dominant over clinoptilolite and clay minerals; and (3) a basal argillic zone where clay minerals are dominant over felsic minerals and clinoptilolite. Interpretation of the mineralogic data, along with lithologic, stratigraphic, and geophysical data from approximately 500 drill holes, reveals a three-layer mineralogic model for the TCU that shows all three zones are extensive beneath Yucca Flat. The mineralogic model will be used to subdivide the TCU in the Yucca Flat hydrostratigraphic framework model, resulting in a more accurate and versatile framework model. In addition, the identification of the type, quantity, and distribution of minerals within each TCU layer will permit modelers to better predict the spatial distribution and extent of contaminant transport from underground tests in Yucca Flat, at both the level of the hydrologic source term and the corrective action unit

  7. Ammonia removal from high salt waste water using natural zeolite; Remocao de amonia de efluentes de alta salinidade utilizando zeolita natural

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Lucia M.L. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil); Arroyo, Pedro A. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas; Barros, Maria Angelica S.D.; Pazin, Elenice [Universidade Estadual de Maringa (UEM), PR (Brazil). Dept. de Quimica; Zola, Andreia S.; Zschornack, Marlon A. [Universidade Estadual de Maringa (UEM), PR (Brazil). Dept. de Quimica. Pos-Graduacao em Engenharia Quimica

    2008-07-01

    The present work aimed to study ammonium ion exchange using a fixed bed of natural zeolite clinoptilolite. First of all, it was carried out a bi component ion exchange of ammonium (150 mg/L) in the presence of K{sup +}, Ba{sup 2+}, Ca{sup 2+}, Sr{sup 2+} e Mg{sup 2+}. Thus, clinoptilolite showed a preference for strontium, barium and potassium cations, while there is a higher preference for Nh{sub 4}{sup +} cations instead calcium and magnesium. Secondly, it was studied the multicomponent ion exchange of ammonium (solution containing all cations). It was observed that the presence of competing cations decreases the content of ammonium retained in the bed until breakthrough point. Furthermore, it was also verified that multicomponent exchange in the presence of high salinity solution (60.000 mg/L of Na{sup +}), sodium influences the ion exchange mechanism, decreasing the up take capacity of ammonium for zeolitic bed. On the other hand, ammonium capture increases in the presence of natural effluent that possesses lower salinity (30.000 mg/L). Therefore, the results obtained evidence the application potentiality of clinoptilolite for ammonia up takes from industrial effluents, in what competition conditions by others cations are too severe and for that the zeolite natural presented good performance. (author)

  8. Zeolites modified with silver for the development of a water disinfection system; Zeolitas modificadas con plata para el desarrollo de un sistema de desinfeccion de agua

    Energy Technology Data Exchange (ETDEWEB)

    Aparicio V, S.

    2013-07-01

    In spite of great strides that have been taken in sanitation technologies, there still exist health problems due to microbiological contamination by water. The waterborne diseases have not been completely eradicated and are a big problem of economic interest and health. Moreover, the microbicidal properties of silver have been used for a long time. The use of silver as a disinfectant has many advantages; for example it inhibits a wide spectrum of microorganisms, it has oligo dynamic properties and owing its mechanisms of cell inactivation, it also does not allow the emergence of new resistant strains. In the present research, the kinetics of water disinfection with silver has been investigated, to develop small system for water disinfection, based in silver modified Mexican clinoptilolite. The chemical species of silver play a significant role in the disinfection processes. For this reason, in this work, were both the Ag{sup +} and nanoparticles of Ag{sup ο} considered. The synthesis of nanoparticles of Ag{sup ο} woes performed by thermal and chemical reduction. It was found that the chemical reduction of Ag{sup +} to Ag{sup ο} was more efficient because it presented more defined nano structures and better distribution than those of thermal reduction. Clinoptilolite of Taxco (Guerrero) was chosen to exchange the native ions from the clinoptilolite by Ag{sup +} from the aqueous medium, or to deposit the nanoparticles of Ag{sup ο} on this surface. These silver modified zeolitic materials were characterized by scanning electron microscopy (Sem), elemental analyses (EDS), X-ray diffraction (XRD) and neutron activation analysis (NAA). The results showed that the crystallographic structure of the clinoptilolite did not change during thermal and chemical reduction treatments of Ag{sup +} to obtain the nanoparticles of Ag{sup ο}. The bactericide activity of the silver modified zeolitic materials (with Ag{sup +} or nanoparticles of Ag{sup ο}) was evaluated on

  9. Selective catalytic reduction of nitric oxide by ammonia over Cu-exchanged Cuban natural zeolites

    International Nuclear Information System (INIS)

    Moreno-Tost, Ramon; Santamaria-Gonzalez, Jose; Rodriguez-Castellon, Enrique; Jimenez-Lopez, Antonio; Autie, Miguel A.; Glacial, Marisol Carreras; Gonzalez, Edel; Pozas, Carlos De las

    2004-01-01

    The catalytic selective reduction of NO over Cu-exchanged natural zeolites (mordenite (MP) and clinoptilolite (HC)) from Cuba using NH 3 as reducing agent and in the presence of excess oxygen was studied. Cu(II)-exchanged zeolites are very active catalysts, with conversions of NO of 95%, a high selectivity to N 2 at low temperatures, and exhibiting good water tolerance. The chemical state of the Cu(II) in exchanged zeolites was characterized by H 2 -TPR and XPS. Cu(II)-exchanged clinoptilolite underwent a severe deactivation in the presence of SO 2 . However, Cu(II)-exchanged mordenite not only maintained its catalytic activity, but even showed a slight improvement after 20h of reaction in the presence of 100ppm of SO 2

  10. Immobilization of radioactive waste in cement-based matrices

    International Nuclear Information System (INIS)

    Glasser, F.P.; Rahman, A.A.; Macphee, D.; McCulloch, C.E.; Angus, M.J.

    1984-01-01

    Model studies of the behaviour of cement systems have been advanced by considering the nature of the phases formed during hydration and deriving pH-composition models for the CaO-SiO 2 -H 2 O system. Preliminary results of Esub(h) measurements are also reported. Leach tests on Sr from cements are interpreted in terms of Sr retention mechanisms. Present results indicate that the aluminate phases in OPC contribute to the chemical retentivity. Studies on cement-clinoptilolite reactions, made using coarse grained clinoptilolite are reported: ferrierite also reacts chemically with cement. Two critical surveys are presented, together with new data: one on the potential of blended cements, the other on cement durability in CO 2 -containing environments. (author)

  11. Management of liquid radioactive waste from research and training laboratories of radiochemistry and radioecology

    International Nuclear Information System (INIS)

    Krasnopyorova, A.P.; Yuhno, G.D.; Sytnik, O.Y.

    2001-01-01

    Full text: Liquid radioactive waste (LRW), that is formed in research and training cycle of radiochemistry and radioecology laboratories of Kharkov National University, corresponds to medium active one (10 5 -10 7 Bq/l). Since the great number of different radioactive isotopes is involved in research conducted by the laboratories, liquid waste contains various radioactive contaminations. As a rule these are the water solutions of salts with concentration of 0.8-1.0 gm/l, containing mixture of 45 Ca, 65 Zn, 90 Sr, 173 Cs radionuclides. Accumulation of liquid waste from the laboratories is comparatively small, approximately 20-30 I per month. A great while LRW from the laboratories had been accumulated in special protective containers and delivered to the central waste disposal. Numerous studies has shown that LRW storage in special containers may only be temporal, since durable holding of waste necessarily gives rise to corrosion of the facing materials, and therefore diffusion of radioactive substances into environment. In addition long-term LRW storage is disadvantageous from economic point of view. Only conversion of LWR into solid state provides safe protection of environment and decreases volumes of waste. At present LRW from the laboratories is necessarily decontaminated and concentrated before being disposed.To that end the sorption methods are used, in which radionuclides from solution are concentrated in solid phase. Since small volumes of LRW are accumulated in the laboratories, the simple scheme of LRW treatment and conversion into solid residual has been designed. It comprises two steps. At the first stage consists in combining of lime-soda-ash softening with the ion-exchange sorption on the finely divided solid sorbent. Natural zeolite, clinoptilolite from Sokimitsk deposit of Ukraine, is used as the sorbent. Usage of clinoptilolite is justified by its high selectivity and sorption power in regard to 90 Sr, 137 Cs, 65 Zn radionuclides. Both low cost and

  12. Use of Spent Zeolite Sorbents for the Preparation of Lightweight Aggregates Differing in Microstructure

    Directory of Open Access Journals (Sweden)

    Wojciech Franus

    2017-02-01

    Full Text Available Lightweight aggregates (LWAs made by sintering beidellitic clay deposits at high temperatures, with and without the addition of spent zeolitic sorbents (clinoptilolitic tuff and Na-P1 made from fly ash containing diesel oil, were investigated. Mineral composition of the aggregates determined by X-ray diffraction was highly uniformized in respect of the initial composition of the substrates. The microstructure of the LWAs, which were studied with a combination of mercury porosimetry, microtomography, nitrogen adsorption/desorption isotherms and scanning electron microscopy, was markedly modified by the spent zeolites, which diminished bulk densities, increased porosities and pore radii. The addition of zeolites decreased water absorption and the compressive strength of the LWAs. The spent Na-P1 had a greater effect on the LWAs’ structure than the clinoptilolite.

  13. Application of chitin and zeolite adsorbents for treatment of low level radioactive liquid wastes

    International Nuclear Information System (INIS)

    Moattar, F.; Hayeripour, S.

    2004-01-01

    Two types of shrimp chitin derivatives and two types of Iranian natural zeolite derivates were studied for adsorption and treatment of low-level radioactive liquid waste. Chitin with lowers than 10% and chitosan with higher than 90% deacetylation factor were selected as neutral organic adsorbents. Natural clinoptilolite of Firuzkooh area and Na from derivates of it were selected as natural inorganic adsorbents. The static and dynamic ion exchange experimental results show that the ad adsorption efficiency depend on particle size, Ph, adsorbent type, deacetylation factor ( in chitin adsorbents) and cation type. The best Cs adsorption occurred in Na from clinoptilolite. Nevertheless chitin derivatives, particularly chitosan, are more efficient than zeolite adsorbents for removing of radionuclides such as 137 Cs, 54 Mn, 90 Sr and 60 Co. Adsorption performance was discussed and compared with each other

  14. South African Family Practice - Vol 59, No 1 (2017)

    African Journals Online (AJOL)

    South African Family Practice. ... The effects of an artificially enhanced clinoptilolite in patients with irritable bowel syndrome · EMAIL FREE FULL ... Nutritional status and metabolic risk in HIV-infected university students: challenges in their ...

  15. Removal of cadmium in urban wastewater with systems based on zeolite type clinoptilolite; Remocion de cadmio en aguas residuales urbanas con sistemas a base de zeolita tipo clinoptilolita

    Energy Technology Data Exchange (ETDEWEB)

    Barragan P, P.

    2016-07-01

    From an environmental issue detected in wastewater samples taken in a municipal wastewater collector in Nogales, Sonora, which is related to cadmium pollution, a research project came out where the principal aim was to implement a system to remove metallic ions of cadmium in wastewater, based on modified and unmodified natural zeolites. The zeolitic material used was natural clinoptilolite modified with NaCl and thiourea, sourced in El Cajon and Guaymas, Sonora. The materials were characterized with X-ray diffraction, Sem, Ft-IR spectra, and Bet analysis. The kinetics of four modified zeolites was investigated at ph=5 and initial concentration of 30 mgL{sup -1} of Cd{sup 2+}. The pseudo-first, the pseudo-second order, and Elovich models were applied to the experimental results. The results best fitted to pseudo-second order model. The maximum sorption capacity of modified zeolites was investigated through isotherms, The Langmuir model, Freundlich, and the combined Langmuir-Freundlich models were applied to the experimental results afterwards. ZGuayThio showed the highest sorption capacity, 11.60 mgg{sup -1}, with R{sup 2}=0.978 according to Langmuir-Freundlich model. Fixed-bed column adsorption experiments were carried out with ZGuayNa and ZGuayThio with three bed heights with 30 mgL{sup -1} solution of Cd{sup 2+}. influent at a flow rate of 1 mLmin{sup -1}, at ph=5. The Thomas, mass balance, and Bed Depth Service Time models were applied to the results. The dynamic adsorption capacity (No) and the constant of sorption velocity (K a) were determined, 28.67 gL{sup -1} and 0.072 Lg{sup -1}min{sup -1} respectively for ZGuayNa with R{sup 2}= 0.9954. Column experiments with municipal wastewater from Colinas del Yaqui sub-collector, previously characterized, were conducted using ZGuayNa and ZGuayThio. A mass transference model was applied to the results which accounted for K{sub p}= 0.815 m{sup 3}Kg{sup -}1 with R{sup 2}= 0.9789 for ZGuayNa, and K{sub p}= 3.1 m{sup 3}Kg

  16. Influence of natural sorbents in immobilization of radioactive waste in cement

    International Nuclear Information System (INIS)

    Plecas, I.; Dimovic, S.

    2006-01-01

    Leach characteristics of 137 Cs and 60 Co radionuclides from spent mix bead ion exchange resins and both ordinary Portland cement and cement mixed with two kind of natural sorbents, (bentonite and clinoptilolite) have been studied using International Atomic Energy's (IAEA) standard leach method. A study is undertaken to determine the waste immobilization performance of low-level wastes in cement-natural sorbents mixtures. The solidification matrix was a standard Portland cement mixed with 290-350 (kg/m 3 ) spent mix bead exchange resins, with or without 1-10 % of bentonite or/and clinoptilolite The leaching rates from the cement-bentonite matrix as 60 Co: (1.20-9.72)x10 -5 (cm/d) and for 137 Cs: (1.00-9.22)x10 -4 (cm/d), after 300 days were measured. From the leaching data the apparent diffusivity of cobalt and cesium in cement bentonite or/and clinoptilolite matrix with a waste load of 350 (kg/m 3 ) spent mix bead exchange resins was measured as 60 Co: (1.0-5.9)x10 -6 (cm 2 /d) and for 137 Cs: (0.48-2.4)x10 -4 (cm 2 /d) after 300 days. The compressive strength of these samples is determined following the ASTM standards. These results are part of a 30-year mortar and concrete testing project which will influence the design of radioactive waste management for a future Serbian radioactive waste disposal center. (author)

  17. The Effect of Applied Organic Fertilizers on the Bioavailability of Heavy Metals in Lolium Perenne, Cultivated on Fly Ash Deposits

    Directory of Open Access Journals (Sweden)

    Smaranda Mâşu

    2011-10-01

    Full Text Available The study aims to monitor the capacity of certain organic fertilizers (volcanic tuff and municipal sludge, applied as such and mixed with volcanic rocks with a high content in clinoptilolite, to determine the covering with vegetation of fly ash deposits resulted from the combustion of lignite in thermal plants. Both biosolids (20 t/ha and volcanic rock with high clinoptilolite content (5 t/ha determined the installation of a vegetative layer and diminished the soil metal bioavailability to the Lolium prerenne plant biomass. When using the organic-zeolite mixture, a synergistic effect is recorded of the two components of the treatment agent and an increase of the biomass with 448%. Moreover, the resulted biomass shows the highest reductions of metal bioaccumulations, of 38-46% for Zn and Fe, of 62% for Cu and between 82-89% for Cr, Ni and Pb.

  18. Catahoula formation of the Texas coastal plain: origin, geochemical evolution, and characteristics of uranium deposits

    International Nuclear Information System (INIS)

    Galloway, W.E.; Kaiser, W.R.

    1979-01-01

    Uranium was released from volcanic glass deposited within the Catahoula through early pedogenic and diagenetic processes. Pedogenesis was the most efficient process for mobilizing uranium. Original uranium content in fresh Catahoula glass is estimated to have averaged at least 10 ppM; about 5 ppM was mobilized after deposition and made available for migration. Uranium was transported predominantly as uranyl dicarbonate ion. Chlorinity mapping reveals modern ground-water flow patterns. Six utranium deposits representative of the ores were studied. Uranium-bearing meteoric waters were reduced by pre-ore stage pyrite formed by extrinsically introduced fault-leaked sulfide or intrinsically by organic matter. Uranium was concentrated in part by adsorption on Ca-montmorillonite cutans, amorphous TiO 2 , and/or organic matter followed by uranyl reduction to U 4+ in amorphous uranous silicates. Clinoptilolite is not correlative with mineralization. Calcite is pervasive throughout host sands but shows no relationship to uranium mineralization. Presence of marcasite and uranium together at the alteration front strongly supports an acid pH during Catahoula mineralization. Maximum adsorption and minimum solubility of uranium occur at pH 6 in carbonate-rich waters. Log activity ratios of individual waters supersaturated with respect to montmorillonite, taken from montmorillonite-clinoptilolite activity diagrams, show positive correlation with uranium mineralization. High Ca 2+ , Mg 2+ , Al(OH) 4 - , and H + activities promote the formation of montmorillonite relative to clinoptilolite. High saturation ratios for montmorillonite show fair correlation with mineralization. The mineral-solution equilibria approach is a potential method of geochemical exploration. 56 figures, 8 tables

  19. Diagenetic Variations between Upper Cretaceous Outcrop and Deeply Buried Reservoir Chalks of the North Sea Area

    DEFF Research Database (Denmark)

    Hjuler, Morten Leth; Fabricius, Ida Lykke

    2007-01-01

    -particle connections and less altered particle shapes. The non-carbonate mineralogy of outcrop chalks is dominated by quartz, occasionally opal-CT and clinoptilolite, and the clay mineral smectite. In offshore chalks quartz still dominates, opal-CT has recrystallized into submicron-size quartz crystals and smectite...

  20. Removal of pyridine from liquid and gas phase by copper forms of natural and synthetic zeolites

    Czech Academy of Sciences Publication Activity Database

    Reháková, M.; Fortunová, L.; Bastl, Zdeněk; Nagyová, S.; Dolinská, S.; Jorík, V.; Jóna, E.

    2011-01-01

    Roč. 186, č. 1 (2011), s. 699-706 ISSN 0304-3894 R&D Projects: GA AV ČR KAN100400702 Institutional research plan: CEZ:AV0Z40400503 Keywords : natural zeolite * clinoptilolite * ZSM5 Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.173, year: 2011

  1. Tribomechanical micronization and activation of whey protein ...

    Indian Academy of Sciences (India)

    Tribomechanics is a part of physics that is concerned with the study of phenomena that appear during milling under dynamic conditions. Tribomechanical micronization and activation (TMA) of whey protein concentrates (WPC) and zeolites (type clinoptilolite) were carried out. Samples of powdered WPC and zeolite were ...

  2. Improving formulated nitrogen, phosphorus and potassium ...

    African Journals Online (AJOL)

    Ammonia volatilization from urea and ammonium containing compound fertilizers cause higher cost of fertilization in agriculture. In this study, an incubation experiment was carried out to compare the effect of different ratios of compound fertilizer amended with clinoptilolite zeolite on NH3 volatilization, soil exchangeable ...

  3. Equilibrium modeling of the formation of zeolites in fractures at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Chipera, S.J.; Bish, D.L.; Carlos, B.A.

    1993-01-01

    Yucca Mountain, in southern Nevada, is currently being investigated to determine its suitability to host the first US high-level nuclear waste repository. One of the reasons that Yucca Mountain was chosen for study is the presence of thick sequences of zeolite-rich horizons. In as much as fractures may serve as potential pathways for aqueous transport, the minerals that line fractures are of particular interest. Zeolites are common in fractures at Yucca Mountain and consist mainly of clinoptilolite/heulandite and mordenite although sporadic occurrences of chabazite, erionite, phillipsite, and stellrite have been identified using X-ray powder diffraction. To understand better the conditions under which the observed zeolite species were formed, thermodynamic data were estimated and calculations of log a((K + ) 2 /Ca ++ ) versus log a((Na + ) 2 /Ca ++ ) were conducted at various temperatures and silica activities. Using present-day Yucca Mountain water chemistries as a lower constraint on silica activity, clinoptilolite/heulandite and mordenite are still the zeolite species that would form under present conditions

  4. Separation of cesium and strontium with zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Kanno, T; Hashimoto, H [Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy

    1976-06-01

    The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it.

  5. Separation of cesium and strontium with zeolites

    International Nuclear Information System (INIS)

    Kanno, Takuji; Hashimoto, Hiroyuki

    1976-01-01

    The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it. (auth.)

  6. Structural simulation of natural zeolites; Simulacion estructural de zeolitas naturales

    Energy Technology Data Exchange (ETDEWEB)

    Sanchez P, E.; Carrera G, L.M. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1997-07-01

    The application of X-ray diffraction (XRD) in the study of crystalline structures of the natural and modified zeolites allows the identification, lattice parameter determination and the crystallinity grade of the sample of interest. Until two decades ago, simulation methods of X-ray diffraction patterns were developed with which was possible to do reliable determinations of their crystalline structure. In this work it is presented the first stage of the crystalline structure simulation of zeolitic material from Etla, Oaxaca which has been studied for using it in the steam production industry and purification of industrial water. So that the natural material was modified for increasing its sodium contents and this material in its turn was put in contact with aqueous solutions of Na, Mg and Ca carbonates. All the simulations were done with the Lazy-Pulverix method. The considered phase was clinoptilolite. It was done the comparison with three clinoptilolite reported in the literature. (Author)

  7. Structural simulation of natural zeolites

    International Nuclear Information System (INIS)

    Sanchez P, E.; Carrera G, L.M.

    1997-01-01

    The application of X-ray diffraction (XRD) in the study of crystalline structures of the natural and modified zeolites allows the identification, lattice parameter determination and the crystallinity grade of the sample of interest. Until two decades ago, simulation methods of X-ray diffraction patterns were developed with which was possible to do reliable determinations of their crystalline structure. In this work it is presented the first stage of the crystalline structure simulation of zeolitic material from Etla, Oaxaca which has been studied for using it in the steam production industry and purification of industrial water. So that the natural material was modified for increasing its sodium contents and this material in its turn was put in contact with aqueous solutions of Na, Mg and Ca carbonates. All the simulations were done with the Lazy-Pulverix method. The considered phase was clinoptilolite. It was done the comparison with three clinoptilolite reported in the literature. (Author)

  8. Purification of Effluent from the Groundwood Production by Organo-zeolite

    Directory of Open Access Journals (Sweden)

    Anić-Vučinić, A.

    2008-11-01

    Full Text Available Wastewaters of the wood processing into groundwood are characterized by increased concentrations of organic contaminants (oils, resin acid, lignin (polymeric phenols, lignin salts (sulphonates, phenoxides, tannins, triglycerides, waxes, free long-chained fatty acids and other. Organic compounds which appear as colour come from extracted lignin, tannins and resin acids. Wood processing effluents are often resistant to degradation using biological methods, and are not removed effectively by conventional physicochemical treatment methods, such as coagulation/flocculation, sedimentation, filtration and ozonation. For processing of those effluents it is often necessary to link different methods of purification, and one of the alternative methods is sorption. In this work the removal of organic pollutants was tested from effluent of the production of mechanically milled groundwood by using sorption to clinoptilolite tuff and to samples of tuff which were modified using the solutions of cationic surfactant- hexadecyltrimethylammonium bromide (HDTMA-Br of different concentrations. The sorption processes of hexadecyltrimethylammonium bromide were researched on the clinoptilolite tuff from Turkey (Aegean Region Turkey, Bigadic, which contains more than 70 % of clinoptilolite, and in smaller mass fraction quartz and opal-CT are present. The tested effluent has the following characteristics: chemical oxygen demand (COD: 13200 mg dm-3, total organic carbon (TOC: 3010 mg dm-3, biochemical oxygen demand (BOD5: 470 mg dm-3, colour: 681 Pt Co, turbidity: 799 NTU, pH 4.8. All testing was done without the adjustment of pH. The conventional process of pre-processing of effluent by coagulation with aluminum chloride hexahydrate (AlCl3·6H2O was tested and the application ofHDTMA-modified clinoptilolite tuff with the intention of further decrease in organic burden of wastewater. In the Fig. 1A the results of the HDTMA uptake onto clinoptilolite tuff are shown, and in

  9. Surface modified natural zeolite as a carrier for sustained diclofenac release: A preliminary feasibility study.

    Science.gov (United States)

    de Gennaro, Bruno; Catalanotti, Lilia; Cappelletti, Piergiulio; Langella, Alessio; Mercurio, Mariano; Serri, Carla; Biondi, Marco; Mayol, Laura

    2015-06-01

    In view of zeolite potentiality as a carrier for sustained drug release, a clinoptilolite-rich rock from California (CLI_CA) was superficially modified with cetylpyridinium chloride and loaded with diclofenac sodium (DS). The obtained surface modified natural zeolites (SMNZ) were characterized by confocal scanning laser microscopy (CLSM), powder X-ray diffraction (XRPD) and laser light scattering (LS). Their flowability properties, drug adsorption and in vitro release kinetics in simulated intestinal fluid (SIF) were also investigated. CLI_CA is a Na- and K-rich clinoptilolite with a cationic exchange ability that fits well with its zeolite content (clinoptilolite=80 wt%); the external cationic exchange capacity is independent of the cationic surfactant used. LS and CLSM analyses have shown a wide distribution of volume diameters of SMNZ particles that, along with their irregular shape, make them cohesive with scarce flow properties. CLSM observation has revealed the localization of different molecules in/on SMNZ by virtue of their chemical nature. In particular, cationic and polar probes prevalently localize in SMNZ bulk, whereas anionic probes preferentially arrange themselves on SMNZ surface and the loading of a nonpolar molecule in/on SMNZ is discouraged. The adsorption rate of DS onto SMNZ was shown by different kinetic models highlighting the fact that DS adsorption is a pseudo-second order reaction and that the diffusion through the boundary layer is the rate-controlling step of the process. DS release in an ionic medium, such as SIF, can be sustained for about 5h through a mechanism prevalently governed by anionic exchange with a rapid final phase. Copyright © 2015 Elsevier B.V. All rights reserved.

  10. Use of natural zeolite-supplemented litter increased broiler production

    African Journals Online (AJOL)

    The aim of this study was to ascertain the influence of natural zeolite, consisting mainly of clinoptilolite and mordenite, as a component of the litter material in broiler houses on the performance of the broilers and on some litter characteristics. Live weight gain, feed consumption, feed efficiency, viability and leg and body ...

  11. Ammonium ion interaction with conditioned natural zeolite with silver and its effect on the disinfection of polluted water in front of a consortium of gram (+) and gram (-) microorganisms

    International Nuclear Information System (INIS)

    Gonzaga G, V. E.

    2013-01-01

    Clinoptilolite zeolite material is a relative abundance in Mexico, which has ion exchange properties, therefore, has the ability to retain metal ions giving it an application in the process of disinfecting of water contaminated with pathogenic microorganisms. In this research, we conducted a study of disinfection of water contaminated with a microbial consortium, from a zeolite rock clinoptilolite from a deposit located in the State of Guerrero. Initially, the zeolite prepared by the grinding and sieving, for conditioning with NaCl and subsequently with AgNO 3 , finally to be characterized using the techniques of scanning electron microscopy and X-ray diffraction. Tests using columns packed with zeolite material, the effect of zeolite bactericidal conditioned with silver (ZGAg) against a microbial consortium consisting of Escherichia coli and Sthapyloccocus aureus in aqueous solution in the presence of ammonium ions used to increase the ion exchange with zeolite fitted with silver. To describe curves disinfecting a continuous flow system is adapted Gu pta model, which describes the kinetics and equilibrium adsorption process, considering the microorganisms as the adsorbate and the sanitizing agent (conditioned with silver zeolite) as the adsorbent. Characterization results show that in the scanning electron microscopy (Sem), no changes were obtained on the morphology of typical clinoptilolite crystals before and after that was modified with sodium and then with silver, it is worth mentioning however that fitted with silver zeolite (ZGAg), small particles are seen on the zeolite material which when analyzed by energy dispersive spectroscopy (EDS), we found a high concentration of Ag +. The disinfection period is increased as the concentration increased ammonium ions, this behavior is attributed to the ion exchange that occurs between the ammonium ions and silver ions. A lower percentage of inactivation is due, therefore, to a lesser amount of money available to be

  12. Comparative study of {sup 137}Cs distribution in broilers and pheasants and possibilities for protection

    Energy Technology Data Exchange (ETDEWEB)

    Mitrovic, Branislava M.; Vitorovic, Gordana; Lazarevic-Macanovic, Mirjana [University of Belgrade, Faculty of Veterinary Medicine, Department of Radiology and Radiation Hygiene, Belgrade (Serbia); Vicentijevic, Mihajlo [Insititute of Veterinary Medicine Serbia, Laboratory of Radiation Hygiene, Belgrade (Serbia); Vitorovic, Dusko [University of Belgrade, Faculty of Agriculture, Department of Animal Science, Belgrade (Serbia); Pantelic, Gordana [Institute of Nuclear Sciences-Vinca, Belgrade (Serbia)

    2012-03-15

    The aim of the present study was to investigate distribution of {sup 137}Cs in leg and breast meat of broilers and pheasants following single alimentary contamination and administration of two protectors (AFCF and clinoptilolite). The birds were administered a single dose of {sup 137}CsCl, with an activity of 750 Bq. Protectors were given via gastric tube or mixed in the forage pellets. AFCF given via gastric tube decreased the {sup 137}Cs concentration by a factor of 7.8 in broilers leg meat and 7.4 in broilers breast meat. When AFCF was mixed in pellets, the {sup 137}Cs concentration was 19.5 times lower in broilers leg meat and 22.1 times lower in broilers breast meat, than in the control group. In pheasants, AFCF administered via gastric tube decreased the {sup 137}Cs concentration by a factor of 12.4 in leg meat and by a factor of 13.7 in breast meat, respectively. In group 4, where pheasants were administered AFCF mixed in pellets, the {sup 137}Cs concentration was 3.7 times lower in leg and breast meat, than in the control group. For comparison, clinoptilolite administered via gastric tube decreased the {sup 137}Cs concentration 1.8 times in broilers leg meat and 2.0 times in breast meat, compared to the control group. In pheasants, {sup 137}Cs concentration was 2.9 times lower in leg meat and 2.6 times lower in breast meat. Clinoptilolite mixed in the feed had relatively low efficiency of protection in broilers ({sup 137}Cs concentration was 1.4 times lower in leg meat and 1.6 lower in breast meat). A similar trend was observed in pheasants ({sup 137}Cs concentration was 1.6 lower in leg and breast meat). (orig.)

  13. The Effects of Light Intensity, Casing Layers, and Layering Styles on Royal Sun Medicinal Mushroom, Agaricus brasiliensis (Higher Basidiomycetes) Cultivation in Turkey.

    Science.gov (United States)

    Adanacioglu, Neşe; Boztok, Kaya; Akdeniz, Ramazan Cengiz

    2015-01-01

    The aim of this research is to evaluate the effects of light intensity, casing layers, and layering styles on the production of the culinary-medicinal mushroom Agaricus brasiliensis in Turkey. The experiments were designed in split-split plots and replicated twice. Three different light intensities-I1, 350 lux; I2, 450 lux; and I3, 750 lux-were used in main plots as environmental factors. A mixture of 4 different casing layers- peat (100%), peat-perlite (75%:25%), peat-clinoptilolite (75%:25%), and peat-perlite-clinoptilolite (60%:20%:20%)-were used at split plots and at split plots. S1, a flat, 3-cm casing layer; S2, a flat, 5-cm casing layer; and S3, casing soil ridges 10 cm wide × 4 cm high, 10 cm apart, were deposited on top of 1-cm overall soil casing layers. At the end of the harvest phase, the total yield was estimated per 100 kg of substrate. Biological efficiency (percentage) was determined from the fresh weight of the mushrooms and the dry weight of the compost at the end of the harvesting period. The highest total yield (7.2 kg/100 kg compost) and biological efficiency (27.63%) were achieved from I2 × peat-perlite-clinoptilolite × S2 treatment. Influence of light intensity, casing layer, layering style, and their interaction in treatments with color values (L*, a*, b*, chroma*, and hue*) also were examined. It has been shown that within color values, chroma* (saturation) values of mushroom caps were affected by light intensity, casing layer, and layering style treatments and light intensity × casing layer treatments and the brightness of mushroom caps tended to increase as light intensity increased.

  14. Comparative study of "1"3"7Cs distribution in broilers and pheasants and possibilities for protection

    International Nuclear Information System (INIS)

    Mitrovic, Branislava M.; Vitorovic, Gordana; Lazarevic-Macanovic, Mirjana; Vicentijevic, Mihajlo; Vitorovic, Dusko; Pantelic, Gordana

    2012-01-01

    The aim of the present study was to investigate distribution of "1"3"7Cs in leg and breast meat of broilers and pheasants following single alimentary contamination and administration of two protectors (AFCF and clinoptilolite). The birds were administered a single dose of "1"3"7CsCl, with an activity of 750 Bq. Protectors were given via gastric tube or mixed in the forage pellets. AFCF given via gastric tube decreased the "1"3"7Cs concentration by a factor of 7.8 in broilers leg meat and 7.4 in broilers breast meat. When AFCF was mixed in pellets, the "1"3"7Cs concentration was 19.5 times lower in broilers leg meat and 22.1 times lower in broilers breast meat, than in the control group. In pheasants, AFCF administered via gastric tube decreased the "1"3"7Cs concentration by a factor of 12.4 in leg meat and by a factor of 13.7 in breast meat, respectively. In group 4, where pheasants were administered AFCF mixed in pellets, the "1"3"7Cs concentration was 3.7 times lower in leg and breast meat, than in the control group. For comparison, clinoptilolite administered via gastric tube decreased the "1"3"7Cs concentration 1.8 times in broilers leg meat and 2.0 times in breast meat, compared to the control group. In pheasants, "1"3"7Cs concentration was 2.9 times lower in leg meat and 2.6 times lower in breast meat. Clinoptilolite mixed in the feed had relatively low efficiency of protection in broilers ("1"3"7Cs concentration was 1.4 times lower in leg meat and 1.6 lower in breast meat). A similar trend was observed in pheasants ("1"3"7Cs concentration was 1.6 lower in leg and breast meat). (orig.)

  15. Ammonium ion interaction with conditioned natural zeolite with silver and its effect on the disinfection of polluted water in front of a consortium of gram (+) and gram (-) microorganisms; Interaccion del ion amonio con zeolita natural acondicionada con plata y su efecto sobre la desinfeccion de agua contaminada frente a un consorcio de microorganismos gram (+) y gram (-)

    Energy Technology Data Exchange (ETDEWEB)

    Gonzaga G, V. E.

    2013-07-01

    Clinoptilolite zeolite material is a relative abundance in Mexico, which has ion exchange properties, therefore, has the ability to retain metal ions giving it an application in the process of disinfecting of water contaminated with pathogenic microorganisms. In this research, we conducted a study of disinfection of water contaminated with a microbial consortium, from a zeolite rock clinoptilolite from a deposit located in the State of Guerrero. Initially, the zeolite prepared by the grinding and sieving, for conditioning with NaCl and subsequently with AgNO{sub 3}, finally to be characterized using the techniques of scanning electron microscopy and X-ray diffraction. Tests using columns packed with zeolite material, the effect of zeolite bactericidal conditioned with silver (ZGAg) against a microbial consortium consisting of Escherichia coli and Sthapyloccocus aureus in aqueous solution in the presence of ammonium ions used to increase the ion exchange with zeolite fitted with silver. To describe curves disinfecting a continuous flow system is adapted Gu pta model, which describes the kinetics and equilibrium adsorption process, considering the microorganisms as the adsorbate and the sanitizing agent (conditioned with silver zeolite) as the adsorbent. Characterization results show that in the scanning electron microscopy (Sem), no changes were obtained on the morphology of typical clinoptilolite crystals before and after that was modified with sodium and then with silver, it is worth mentioning however that fitted with silver zeolite (ZGAg), small particles are seen on the zeolite material which when analyzed by energy dispersive spectroscopy (EDS), we found a high concentration of Ag +. The disinfection period is increased as the concentration increased ammonium ions, this behavior is attributed to the ion exchange that occurs between the ammonium ions and silver ions. A lower percentage of inactivation is due, therefore, to a lesser amount of money available to

  16. Petrology and geochemistry of samples from bed-contact zones in Tunnel Bed 5, U12g-Tunnel, Nevada Test Site

    International Nuclear Information System (INIS)

    Connolly, J.R.; Keil, K.; Mansker, W.L.; Allen, C.C.; Husler, J.; Lowy, R.; Fortney, D.R.; Lappin, A.R.

    1984-10-01

    This report summarizes the detailed geologic characterization of samples of bed-contact zones and surrounding nonwelded bedded tuffs, both within Tunnel Bed 5, that are exposed in the G-Tunnel complex beneath Rainier Mesa on the Nevada Test Site (NTS). Original planning studies treated the bed-contact zones in Tunnel Bed 5 as simple planar surfaces of relatively high permeability. Detailed characterization, however, indicates that these zones have a finite thickness, are depositional in origin, vary considerably over short vertical and horizontal distances, and are internally complex. Fluid flow in a sequence of nonwelded zeolitized ash-flow or bedded tuffs and thin intervening reworked zones appears to be a porous-medium phenomenon, regardless of the presence of layering. There are no consistent differences in either bulk composition or detailed mineralogy between bedded tuffs and bed-contact zones in Tunnel Bed 5. Although the original bulk composition of Tunnel Bed 5 was probably peralkaline, extensive zeolitization has resulted in a present peraluminous bulk composition of both bedded tuffs and bed-contact zones. The major zeolite present, clinoptilolite, is intermediate (Ca:K:Na = 26:35:39) and effectively uniform in composition. This composition is similar to that of clinoptilolite from the tuffaceous beds of Calico Hills above the static water level in hole USW G-1, but somewhat different from that reported for zeolites from below the static water level in USW G-2. Tunnel Bed 5 also contains abundant hydrous manganese oxides. The similarity in composition of the clinoptilolites from Tunnel Bed 5 and those above the static water level at Yucca Mountain indicates that many of the results of nuclide-migration experiments in Tunnel Bed 5 would be transferrable to zeolitized nonwelded tuffs above the static water level at Yucca Mountain

  17. Influence of Zeolite on fatty acid composition and egg quality in Tunisian Laying Hens

    Directory of Open Access Journals (Sweden)

    Fendri Imen

    2012-06-01

    Full Text Available Abstract Background The health benefits of omega-3 and omega-6 polyunsaturated fatty acids (PUFA are generally recognized. Unfortunately, in most Mediterranean countries, the recommended daily intake of these compounds is rarely met. Therefore, enrichment of commonly occurring foods can boost intake of these fatty acids. In this regard, eggs are an interesting target, as they form an integral part of the diet. Result Zeolite (Clinoptilolites was added to Laying Hens feed at concentrations 1% or 2% and was evaluated for its effects on performance of the production and on egg quality. The Laying Hens were given access to 110 g of feed mixtures daily that was either a basal diet or a ‘zeolite diet’ (the basal diet supplemented with clinoptilolite at a level of 1% or 2%. It was found that zeolite treatment had a positive and significatif (p  Conclusion This study showed the significance of using zeolite, as a feed additive for Laying Hens, as part of a comprehensive program to control egg quality and to increase level of polyunsaturated fatty acids on egg.

  18. Research by ESS Division for the Nevada Nuclear Waste Storage Investigations: Progress report, January-June 1985

    International Nuclear Information System (INIS)

    Vaniman, D.

    1987-10-01

    Petrographic research for the Nevada Nuclear Waste Storage Investigations focused on xenolithic variability in the Topopah Spring Member and on variations of clinoptilolite composition at Yucca Mountain. Zeolite and smectite occurrences were considered in terms of their relation to a disturbed zone beneath the potential repository, and mineral stability experiments have produced a new clinoptilolite structure as a result of prolonged heating at low temperature. Limitations were defined on the abundance of erionite and of sulfur. X-ray diffraction studies lead to improved analytical methods. Progress was made in the comparative study of mineralogy in sand ramps and in faults. Geological modeling considered the differences of the diffusion of nonsorbing tracers in vertically and in horizontally fractured rock. Modeling also treated the diffusion of a nonsorbing tracer in devitrified and in zeolitized rock. The results of these experiments in all cases show relatively symmetrical two-dimensional diffusion patterns. Preliminary calculations compare the dispersion/diffusion of nonsorbing Tc with the dispersion/diffusion/sorption of U. 27 refs., 20 figs., 5 tabs

  19. Surface modification of a natural zeolite by treatment with cold oxygen plasma: Characterization and application in water treatment

    Science.gov (United States)

    De Velasco-Maldonado, Paola S.; Hernández-Montoya, Virginia; Montes-Morán, Miguel A.; Vázquez, Norma Aurea-Rangel; Pérez-Cruz, Ma. Ana

    2018-03-01

    In the present work the possible surface modification of natural zeolite using cold oxygen plasma was studied. The sample with and without treatment was characterized using nitrogen adsorption isotherms at -196 °C, FT-IR spectroscopy, SEM/EDX analysis and X-Ray Diffraction. Additionally, the two samples were used for the removal of lead and acid, basic, reactive and food dyes in batch systems. The natural zeolite was found to be a mesoporous material with a low specific surface area (23 m2/g). X-ray patterns confirmed that clinoptilolite was the main crystal structure present in the natural zeolite. The molecular properties of dyes and the zeolitic structure were studied using molecular simulation, with the purpose to understand the adsorption mechanism. The results pointed out that only the roughness of the clinoptilolite was affected by the plasma treatment, whereas the specific surface area, chemical functionality and crystal structure remained constant. Finally, adsorption results confirmed that the plasma treatment had no significant effects on the dyes and lead retention capacities of the natural zeolite.

  20. Alginate Production from Alternative Carbon Sources and Use of Polymer Based Adsorbent in Heavy Metal Removal

    Directory of Open Access Journals (Sweden)

    Çiğdem Kıvılcımdan Moral

    2016-01-01

    Full Text Available Alginate is a biopolymer composed of mannuronic and guluronic acids. It is harvested from marine brown algae; however, alginate can also be synthesized by some bacterial species, namely, Azotobacter and Pseudomonas. Use of pure carbohydrate sources for bacterial alginate production increases its cost and limits the chance of the polymer in the industrial market. In order to reduce the cost of bacterial alginate production, molasses, maltose, and starch were utilized as alternative low cost carbon sources in this study. Results were promising in the case of molasses with the maximum 4.67 g/L of alginate production. Alginates were rich in mannuronic acid during early fermentation independent of the carbon sources while the highest guluronic acid content was obtained as 68% in the case of maltose. The polymer was then combined with clinoptilolite, which is a natural zeolite, to remove copper from a synthetic wastewater. Alginate-clinoptilolite beads were efficiently adsorbed copper up to 131.6 mg Cu2+/g adsorbent at pH 4.5 according to the Langmuir isotherm model.

  1. Nuclear waste treatment using Iranian natural zeolites

    International Nuclear Information System (INIS)

    Kazemian, H.; Ghannadi Maraghe, M.

    2001-01-01

    Full text: The zeolite researches in Iran is a relatively new subject which has started about 10 years ago. The motivation for this scientific and interesting field was provided after discovery of significant deposits of natural zeolites in different regions of Iran as well as further developments of research institutions and the national concern to environmental protection especially the wastewater clean-up in point of view of recycling of such waste water to compensate some needs to water in other utilizations. This paper intends to review and describes scientific researches which have done on using zeolites in the field of nuclear waste treatment in Iran to introduce the potential resources to the world in more details. Zeolite tuffs are widely distributed in huge deposits in different regions of Iran. So far, the clinoptilolite tuffs are the most abundant natural zeolite which exist with zeolite content of 65%- 95%. Nowadays several different types of Iranian natural zeolites are characterized in point of view of chemical composition, type of structure, chemical, thermal, and radiation resistance using different instrumental and classical methods such as; X-ray diffraction (XRD), X-ray fluoresce (XRF), thermal methods of analysis (TA), scanning electron microscopy (SEM), analytical chemistry and radioanalytical methods as well as different ion-exchange techniques (e.g.3-7). The ability of Iranian natural clinoptilolite for removal of some fission products from nuclear wastewaters have been investigated. The selectivity of all investigated zeolites toward radiocesium and radiostrontium have been promising (e.g. 8-10). The successful synthesize of P zeolite from Iranian clinoptilolite-reach tuffs under different conditions were performed. The compatibility of zeolites with glass and cement matrices, for final disposal of radwaste, as well as their selectivity toward most dangerous heat generating radionuclides (e.g. 137 Cs and 90 Sr) is very important in using

  2. Adsorption study for uranium in Rocky Flats groundwater

    International Nuclear Information System (INIS)

    Laul, J.C.; Rupert, M.C.; Harris, M.J.; Duran, A.

    1995-01-01

    Six adsorbents were studied to determine their effectiveness in removing uranium in Rocky Flats groundwater. The bench column and batch (Kd) tests showed that uranium can be removed (>99.9%) by four adsorbents. Bone Charcoal (R1O22); F-1 Alumina (granular activated alumina); BIOFIX (immobilized biological agent); SOPBPLUS (mixed metal oxide); Filtrasorb 300 (granular activated carbon); and Zeolite (clinoptilolite)

  3. Plant productivity and characterization of zeoponic substrates after three successive crops of radish

    Science.gov (United States)

    Gruener, J. E.; Ming, Doug; Galindo, C., Jr.; Henderson, K. E.

    2006-01-01

    The National Aeronautics and Space Administration (NASA) has developed advanced life support (ALS) systems for long duration space missions that incorporate plants to regenerate the atmosphere (CO2 to O2), recycle water (via evapotranspiration), and produce food. NASA has also developed a zeolite-based synthetic substrate consisting of clinoptilolite and synthetic apatite to support plant growth for ALS systems (Ming et al., 1995). The substrate is called zeoponics and has been designed to slowly release all plant essential elements into "soil" solution. The substrate consists of K- and NH4-exchanged clinoptilolite and a synthetic hydroxyapatite that has Mg, S, and the plant-essential micronutrients incorporated into its structure in addition to Ca and P. Plant performance in zeoponic substrates has been improved by the addition of dolomite pH buffers, nitrifying bacteria, and other calcium-bearing minerals (Henderson et al., 2000; Gruener et al., 2003). Wheat was used as the test crop for all of these studies. The objectives of this study were to expand upon the previous studies to determine the growth and nutrient uptake of radish in zeoponic substrates and to determine the nutrient availability of the zeoponic substrate after three successive radish crops.

  4. Treatment of medium-active liquid wastes by methods of electrocoagulation and ionic exchange method

    International Nuclear Information System (INIS)

    Krasnopyorova, A.P.; Ionenko, V.I.; Sytnik, O.Yu.; Lebedeva, L.T.; Gukovin, V.I.

    2001-01-01

    Since small volumes of LRW are accumulated in the laboratories, the simple scheme of LRW treatment and conversion into solid residual has been designed. It comprises two stages. The first stage is in the application of a electrical coagulation method with the application of aluminium electrodes. Additives of natural zeolite - clinoptilolite accelerate the formation process of a dense residue. Formed precipitate is removed by filtration through the vacuum pump with belting filter, impregnated by vegetable extract that contains tannins. Tannins are the natural complexing agents binding radionuclides into insoluble complexes. Thereby additional purification of the solutions from radionuclides is achieved. Received filtrate is tested for radionuclide content with standard techniques of β-γ-spectrometry and radiochemistry. In the method of LRW treatment, the bulk of radionuclides is removed as precipitate: Ca-45(100%), Sr-90(99.8%), Zn-65(99.5%), Cs-137(99.8%). Further decontamination of the received filtrate of LRW is achieved by filtration through the tower, filled with finely divided clinoptilolite. The highly developed surface of the powdered sorbent essentially improves kinetics of sorption, permits to decrease sorbent-sorbate contact time and use the sorbent capacity almost entirely. (authors)

  5. Aflatoxin B1 adsorption by the natural aluminosilicates - concentrate of montmorillonite and zeolite

    Directory of Open Access Journals (Sweden)

    Marković Marija A.

    2016-01-01

    Full Text Available Aflatoxin B1 adsorption by the concentrate of bentonite clay - montmorillonite and the natural zeolite - clinoptilolite and was investigated at the initial toxin concentration 4 ppm, with different amonunts of solid phase in suspension (10, 5, 2 and 1 mg/10 mL and different pH values - 3, 7 and 9. Results indicated that for both minerals, decreasing the amount of solid phase in suspension, decrease the amount of active sites relevant for adsorption of aflatoxin B1. Thus, for concentrate of montnorillonite, at the lowest level of solid phase in suspension (1 mg/10 mL, aflatoxin B1 adsorption indexes were 97% at pH 3, 88% at pH 7 and 82% at pH 9, while for the natural zeolite, adsorption of toxin was 9% at pH 3 and 7% at pH 7 and 9. Since inorganic cations in minerals are mainly responsible for aflatoxin B1 adsorption, even the natural zeolite - clinoptilite has much higher cation exchange capacity (the content of inorganic exchangeable cations compared to the concentrate of montmorillonite, adsorption of aflatoxin B1 by this mineral is much lower. Comparing the molecular dimensions of aflatoxin B1 molecule with the dimension of channels of clinoptilolite and interlamellar space of montmorillonite it is obvious that this toxin is adsorbed only at the external surface of clinoptilolite while in the montmorillonite all active sites are equally available for its adsorption. Thus, the concentrate of montmorillonite posess by higher adsorption capacity for aflatoxin B1. Results presented in this paper confirmed the fact the differences in the structure of minerals led to their different efficiency for adsorption of aflatoxin B1. Mineralogical and chemical composition, determination of cation exchange capacity, etc., are very important parameters influencing the effectiveness of minerals as aflatoxin B1 adsorbents. [Projekat Ministarstva nauke Republike Srbije, br. 451-03-2802-IP Tip1/142, br. 172018 i br. 34013

  6. Photodynamic dye adsorption and release performance of natural zeolite

    OpenAIRE

    Hovhannisyan, Vladimir; Dong, Chen-Yuan; Chen, Shean-Jen

    2017-01-01

    Clinoptilolite type of zeolite (CZ) is a promising material for biomedicine and pharmaceutics due to its non-toxicity, thermal stability, expanded surface area, and exceptional ability to adsorb various atoms and organic molecules into micropores. Using multiphoton microscopy, we demonstrated that individual CZ particles produce two-photon excited luminescence and second harmonic generation signal at femtosecond laser excitation, and adsorb photo-dynamically active dyes such as hypericin and ...

  7. Influence of Zeolite on fatty acid composition and egg quality in Tunisian Laying Hens

    Science.gov (United States)

    2012-01-01

    Background The health benefits of omega-3 and omega-6 polyunsaturated fatty acids (PUFA) are generally recognized. Unfortunately, in most Mediterranean countries, the recommended daily intake of these compounds is rarely met. Therefore, enrichment of commonly occurring foods can boost intake of these fatty acids. In this regard, eggs are an interesting target, as they form an integral part of the diet. Result Zeolite (Clinoptilolites) was added to Laying Hens feed at concentrations 1% or 2% and was evaluated for its effects on performance of the production and on egg quality. The Laying Hens were given access to 110 g of feed mixtures daily that was either a basal diet or a ‘zeolite diet’ (the basal diet supplemented with clinoptilolite at a level of 1% or 2%). It was found that zeolite treatment had a positive and significatif (p zeolite supplementation tended to/or has no significant effects on total egg, eggshell, yolk and albumen weights. It was found also that zeolite mainly increases level of polyunsaturated fatty acids in egg. Conclusion This study showed the significance of using zeolite, as a feed additive for Laying Hens, as part of a comprehensive program to control egg quality and to increase level of polyunsaturated fatty acids on egg. PMID:22676421

  8. Environmental application of modified natural zeolites

    International Nuclear Information System (INIS)

    Nikashina, V.A.; Myasoedov, B.F.

    1998-01-01

    The following techniques were used for the chemical modification of the natural zeolites: (1) treatment of natural zeolites with organic substances. Examples of applications of these sorbents to the decontamination and disinfection of solutions of different composition and surface waters are presented. (2) Treatment of the natural zeolites with a inorganic substances. (2.1) The clinoptilolite-rich tuffs were treated with a hot suspensions of freshly precipitated magnetite. This leads to the preparation of sorbents possessing magnetic properties. The radionuclides and heavy metals recovery from soils and silts was investigated using different soil and ferromagnetic zeolite weights ratios and contact times. Different soils and sorbent of varying capacities were used for these investigations. As example, the recovery 137 Cs and 85 Sr from soils of different nature is presented. (2.2) Treatment of natural zeolites with Fe-containing solutions of Fe-containing natural waters. The filtration of these solutions through clinoptilolite-rich tuffs makes leads to preparation of materials possessing high selectivity to PO 4 3- ions. The properties of these sorbents can be utilized for the PO 4 3+ decontamination of waters (e.g. waste waters) and for the subsequent use of these materials in agriculture as fertilizers.(author)

  9. Dissolution of Iron During Biochemical Leaching of Natural Zeolite

    Directory of Open Access Journals (Sweden)

    Lengauer C.

    2004-12-01

    Full Text Available Natural zeolite, including clinoptilolite, often contains iron and manganese which decrease the whiteness of this sharp angular material.The biological treatment of zeolite enables its use as an substitute for tripolyphosphates in wash powders which have to comply with strict requirements as far as whiteness is concerned and rounded off grain content. Insoluble Fe3+ and Mn4+ in the zeolite could be reduced to soluble Fe2+ and Mn2+ by silicate bacteria of Bacillus spp. These metals were efficiently removed from zeolite as documented by Fe2O3 decrease (from 1.37% to 1.08% and MnO decrease (from 0.022% to 0.005% after bioleaching. The whiteness of zeolite was increased by 8%. The leaching effect, observed by scanning electron microscopy, caused also a chamfer of the edges of sharp angular grains. Despite the enrichment by fine-grained fraction, the decrease of the surface area of clinoptilolite grains from the value 24.94 m2/g to value 22.53 m2/g was observed. This fact confirms the activity of bacteria of Bacillus genus in the edge corrosion of mineral grains.Removal of iron and manganese as well as of sharp edges together with the whiteness increase would provide a product suitable for industrial applications.

  10. Synthesis and characterization of inorganic materials to be employees as adsorbents of toxic metals; Sintesis y caracterizacion de materiales inorganicos para ser empleados como adsorbentes de metales toxicos y de interes nuclear

    Energy Technology Data Exchange (ETDEWEB)

    Granados C, F.; Serrano G, J.; Bonifacio M, J., E-mail: francisco.granados@inin.gob.m [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

    2010-07-01

    In this chapter is described the development of the studies realized in the Instituto Nacional de Investigaciones Nucleares (ININ) by researchers of the Chemistry Department in the area of water decontamination. The study of the metals separation in aqueous solution through inorganic adsorbents, was initiated in the Chemistry Department, using zeolites for to adsorb metal cations like the cobalt and cadmium. In the year 1995, the separation studies of Co and Cd were realized using zeolite X. On the other hand, the adsorption capacity of the natural clinoptilolite to retain to the cobalt was also studied. With the natural evolution of these works, it began to study the effect of the organic compounds presence in the metals adsorption in zeolites. Apart from the Co and Cd the removal of Ni, Cd and Zn of the water has been investigated using clinoptilolite, heulandite and Hg, also using zeolites like adsorbent material. In the last years, they have been carried out studies on the separation of Cr in form of chromate (CrO{sub 4}{sup 2-}) as of dichromate ions (Cr{sub 2}O{sub 7}{sup 2-}), using pouzzolane modified with Fe and tricalcic phosphate. In these works were found that both materials are highly efficient to separate the chromium of aqueous solutions. (Author)

  11. Application of engineered sorbent barriers Summary of Laboratory Data for FY 1988

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Jones, E.O.

    1989-09-01

    Laboratory studies were conducted in FY 1988 Pacific Northwest Laboratory to determine the effect of contact time, pH, solution to solid ratio, and particle size on the performance of a number of materials in adsorbing radioactive cobalt, strontium, and cesium. The laboratory studies were conducted to provide background information useful in designing an engineered sorbent barrier, which restricts the migration of radionuclides from low-level waste sites. Understanding how the variables affect the adsorption of ions on the sorbent materials is the key to estimating the performance of sorbent barriers under a variety of conditions. The scope of the studies was limited to three radionuclides and four sorbent materials, but the general approach can be used to evaluate other radionuclides and conditions. The sorbent materials evaluated in this study included clinoptilolite, activated carbon, bentonite clay, and Savannah River soil. The clinoptilolite and activated carbon were identified in previous studies as the most cost-effective materials for sorption of the three radionuclides under consideration. The bentonite clay was evaluated as a component of the barrier that could be used to modify the permeability of the barrier system. The Savannah River soil was used to represent soil from a humid site. 3 refs., 14 figs., 1 tab.

  12. Synthesis and characterization of Zinc (II)-loaded Zeolite/Graphene oxide nanocomposite as a new drug carrier

    Energy Technology Data Exchange (ETDEWEB)

    Khatamian, M. [Inorganic Chemistry Department, Faculty of Chemistry, University of Tabriz, C.P. 51664 Tabriz (Iran, Islamic Republic of); Divband, B., E-mail: baharakdivband@yahoo.com [Research Center for Pharmaceutical Nanotechnology, Tabriz University of Medical Sciences, Tabriz (Iran, Islamic Republic of); Inorganic Chemistry Department, Faculty of Chemistry, University of Tabriz, C.P. 51664 Tabriz (Iran, Islamic Republic of); Farahmand-zahed, F. [Inorganic Chemistry Department, Faculty of Chemistry, University of Tabriz, C.P. 51664 Tabriz (Iran, Islamic Republic of)

    2016-09-01

    Current research has focused on the preparation of Zinc-clinoptilolite/Graphene Oxide (Zn-Clin/GO) hybrid nanostructure and investigating its biocompatibility for the first time. As prepared samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Thermo gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). In order to use it as a drug carrier two important factors were investigated: cytocompatibility of nanocomposites and their drug loading capacity. The results showed that the prepared nanocomposite is cytocompatible and its high loading capacity and slow release performance for Doxorubicin (DOX), as a cancer drug, proved that it can be used as a drug carrier. At last in-vitro toxicity of DOX loaded nanocomposite was compared with pure DOX. - Graphical abstract: Biocompatible Zn-clinoptilolite/Graphene oxide hybrid nanostructure as in vitro drug delivery systems (DDS) was able to store and release substantial amounts of doxorubicin to the lung cancer cell lines. Display Omitted - Highlights: • Zn-Clin/GO nanocomposite as a new in vitro drug carrier with high loading capacity is synthesized. • Two synthesis methods (Microwave assisted hydrothermal method and Reflux method) are used. • All of the carriers (Zn-Clin, Zn-Clin/GO, GO) showed high biocompatibility.

  13. Synthesis and characterization of Zinc (II)-loaded Zeolite/Graphene oxide nanocomposite as a new drug carrier

    International Nuclear Information System (INIS)

    Khatamian, M.; Divband, B.; Farahmand-zahed, F.

    2016-01-01

    Current research has focused on the preparation of Zinc-clinoptilolite/Graphene Oxide (Zn-Clin/GO) hybrid nanostructure and investigating its biocompatibility for the first time. As prepared samples were characterized by X-ray diffraction (XRD), Scanning electron microscopy (SEM), Thermo gravimetric analysis (TGA) and Fourier transform infrared (FT-IR). In order to use it as a drug carrier two important factors were investigated: cytocompatibility of nanocomposites and their drug loading capacity. The results showed that the prepared nanocomposite is cytocompatible and its high loading capacity and slow release performance for Doxorubicin (DOX), as a cancer drug, proved that it can be used as a drug carrier. At last in-vitro toxicity of DOX loaded nanocomposite was compared with pure DOX. - Graphical abstract: Biocompatible Zn-clinoptilolite/Graphene oxide hybrid nanostructure as in vitro drug delivery systems (DDS) was able to store and release substantial amounts of doxorubicin to the lung cancer cell lines. Display Omitted - Highlights: • Zn-Clin/GO nanocomposite as a new in vitro drug carrier with high loading capacity is synthesized. • Two synthesis methods (Microwave assisted hydrothermal method and Reflux method) are used. • All of the carriers (Zn-Clin, Zn-Clin/GO, GO) showed high biocompatibility.

  14. Mineralogic studies of tuff for high-level waste disposal

    International Nuclear Information System (INIS)

    Vaniman, D.; Bish, D.; Broxton, D.; Byers, F.; Carlos, B.; Levy, S.

    1986-01-01

    The volcanic rocks at Yucca Mountain, Nevada, consist predominantly of tuff that originated 12 to 14 million years ago as flows and airfalls of hot volcanic particulates. On cooling these units formed two major rock types: crystallized zones formed mostly of feldspar and silica minerals, and zones of glass. Alteration of glass to zeolite minerals occurred largely during structural tilting of Yucca Mountain in the ∼1-3 million years following the major eruptions. The compositions of zeolites formed from glasses strongly indicate open-system chemical exchange. Superimposed on this general alteration of glasses are areas of local high-temperature alteration. High-temperature alteration ended by 11 million years ago. Zeolites such as clinoptilolite persisted during high-temperature alteration at temperatures up to 100 degree C, suggesting that clinoptilolite at Yucca Mountain close to the thermally disturbed zone around a repository may also survive heating to temperatures at least this high. The mineralogic data from tuff at Yucca Mountain will ultimately be used by the Department of Energy Nevada Nuclear Waste storage Investigations for (1) defining the mineralogic component in estimating waste element travel times away from the repository and (2) determining the past history of alteration and the anticipated stability of minerals near the repository

  15. Characterization of Mongolian Natural Minerals and Their Application for Heavy Metal Adsorbent

    OpenAIRE

    Dolgormaa, Munkhbat; Shiomori, Koichiro; Bayanjargal, Ochirkhuyag

    2016-01-01

    In this study, the structural characteristic and the adsorption properties of heavy metals on Mongolian natural minerals were investigated. The natural samples were confirmed as Heulandite group of Clinoptilolite type zeolite and clay sample that contains albite and quartz by X-ray diffraction analysis. According to BET surface analysis, natural zeolites have mesoporous type of pore. The results of adsorption study showed that adsorption ability of natural zeolite is high effective for lead i...

  16. Study of the Cd (II) removal in the presence of methyl orange with a natural zeolite conditioned with iron nanoparticles; Estudio de la remocion de Cd(II) en presencia de naranja de metilo con una zeolita natural acondicionada con nanoparticulas de hierro

    Energy Technology Data Exchange (ETDEWEB)

    Xingu C, E. G.

    2015-07-01

    This work presents a study on the removal of cadmium and/or methyl-orange dye in aqueous solution, using natural zeolite clinoptilolite, as sodium homo-ionized and impregnated with iron nanoparticles. Iron nanoparticles were synthesized in the presence of the zeolite by chemical reduction. The evaluation of the removal ability was performed in a monocomponent (cadmium or methyl-orange dye) system by varying the contact time and its initial concentration. Removal capacity in a bi-component (cadmium and methyl orange) system was also studied while varying their concentrations. The characterization of the zeolites, before and after the sorption process, was carried out using several analytical techniques. The characteristics of zeolite clinoptilolite and iron particles were observed by scanning electron microscopy. The iron particles showed diameter sizes between 60 and 200 nm, localized on the surface of the zeolite. By IR spectroscopy no structural changes were detected for any of the treatments made to the zeolitic materials. By X-ray diffraction the clinoptilolite crystalline phase was mainly identified, however, it failed to detect any phase of iron in the zeolite impregnated with iron nanoparticles. Moessbauer spectroscopy indeed detected the impregnated iron phase as iron borides. The homo-ionized and iron nanoparticles impregnated zeolite showed no change in the specific surface area, or the isoelectric point, their values were 22.3 m{sup 2}/g and ph 9.8, respectively. However, whereas the active site density for the homo-ionized zeolite was 2.87 sites/nm{sup 2}, for iron nanoparticles impregnated zeolite was 20.32 sites/nm{sup 2}. As a result of the analysis of the isotherms of cadmium, the maximum sorption capacity of the homo-ionized zeolite was 35.03 mg/g and for the iron nanoparticles impregnated zeolite was 36.43 mg/g. These maximum sorption capacities represent up to 85% of removed cadmium from concentrations of 50 to 600 mg/L. For the removal of methyl

  17. Study of the Cd (II) removal in the presence of methyl orange with a natural zeolite conditioned with iron nanoparticles

    International Nuclear Information System (INIS)

    Xingu C, E. G.

    2015-01-01

    This work presents a study on the removal of cadmium and/or methyl-orange dye in aqueous solution, using natural zeolite clinoptilolite, as sodium homo-ionized and impregnated with iron nanoparticles. Iron nanoparticles were synthesized in the presence of the zeolite by chemical reduction. The evaluation of the removal ability was performed in a monocomponent (cadmium or methyl-orange dye) system by varying the contact time and its initial concentration. Removal capacity in a bi-component (cadmium and methyl orange) system was also studied while varying their concentrations. The characterization of the zeolites, before and after the sorption process, was carried out using several analytical techniques. The characteristics of zeolite clinoptilolite and iron particles were observed by scanning electron microscopy. The iron particles showed diameter sizes between 60 and 200 nm, localized on the surface of the zeolite. By IR spectroscopy no structural changes were detected for any of the treatments made to the zeolitic materials. By X-ray diffraction the clinoptilolite crystalline phase was mainly identified, however, it failed to detect any phase of iron in the zeolite impregnated with iron nanoparticles. Moessbauer spectroscopy indeed detected the impregnated iron phase as iron borides. The homo-ionized and iron nanoparticles impregnated zeolite showed no change in the specific surface area, or the isoelectric point, their values were 22.3 m"2/g and ph 9.8, respectively. However, whereas the active site density for the homo-ionized zeolite was 2.87 sites/nm"2, for iron nanoparticles impregnated zeolite was 20.32 sites/nm"2. As a result of the analysis of the isotherms of cadmium, the maximum sorption capacity of the homo-ionized zeolite was 35.03 mg/g and for the iron nanoparticles impregnated zeolite was 36.43 mg/g. These maximum sorption capacities represent up to 85% of removed cadmium from concentrations of 50 to 600 mg/L. For the removal of methyl orange dye

  18. Sampling and Analysis Plan for N-Springs ERA pump-and-treat waste media

    International Nuclear Information System (INIS)

    Stankovich, M.T.

    1996-07-01

    This Sampling and Analysis Plan details the administrative procedures to be used to conduct sampling activities for characterization of spent ion-exchange resin, clinoptilolite, generated from the N-Springs pump-and-treat expedited response action. N-Springs (riverbank seeps) is located in the 100-N Area of the Hanford Site. Groundwater contained in the 100-NR-2 Operable Unit is contaminated with various radionuclides derived from wastewater disposal practices and spills associated with 100-N Reactor Operations

  19. Effects of earthworm casts and zeolite on the two-stage composting of green waste

    International Nuclear Information System (INIS)

    Zhang, Lu; Sun, Xiangyang

    2015-01-01

    Highlights: • Earthworm casts (EWCs) and clinoptilolite (CL) were used in green waste composting. • Addition of EWCs + CL improved physico-chemical and microbiological properties. • Addition of EWCs + CL extended the duration of thermophilic periods during composting. • Addition of EWCs + CL enhanced humification, cellulose degradation, and nutrients. • Combined addition of 0.30% EWCs + 25% CL reduced composting time to 21 days. - Abstract: Because it helps protect the environment and encourages economic development, composting has become a viable method for organic waste disposal. The objective of this study was to investigate the effects of earthworm casts (EWCs) (at 0.0%, 0.30%, and 0.60%) and zeolite (clinoptilolite, CL) (at 0%, 15%, and 25%) on the two-stage composting of green waste. The combination of EWCs and CL improved the conditions of the composting process and the quality of the compost products in terms of the thermophilic phase, humification, nitrification, microbial numbers and enzyme activities, the degradation of cellulose and hemicellulose, and physico-chemical characteristics and nutrient contents of final composts. The compost matured in only 21 days with the optimized two-stage composting method rather than in the 90–270 days required for traditional composting. The optimal two-stage composting and the best quality compost were obtained with 0.30% EWCs and 25% CL

  20. Effects of earthworm casts and zeolite on the two-stage composting of green waste

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Lu, E-mail: zhanglu1211@gmail.com; Sun, Xiangyang, E-mail: xysunbjfu@gmail.com

    2015-05-15

    Highlights: • Earthworm casts (EWCs) and clinoptilolite (CL) were used in green waste composting. • Addition of EWCs + CL improved physico-chemical and microbiological properties. • Addition of EWCs + CL extended the duration of thermophilic periods during composting. • Addition of EWCs + CL enhanced humification, cellulose degradation, and nutrients. • Combined addition of 0.30% EWCs + 25% CL reduced composting time to 21 days. - Abstract: Because it helps protect the environment and encourages economic development, composting has become a viable method for organic waste disposal. The objective of this study was to investigate the effects of earthworm casts (EWCs) (at 0.0%, 0.30%, and 0.60%) and zeolite (clinoptilolite, CL) (at 0%, 15%, and 25%) on the two-stage composting of green waste. The combination of EWCs and CL improved the conditions of the composting process and the quality of the compost products in terms of the thermophilic phase, humification, nitrification, microbial numbers and enzyme activities, the degradation of cellulose and hemicellulose, and physico-chemical characteristics and nutrient contents of final composts. The compost matured in only 21 days with the optimized two-stage composting method rather than in the 90–270 days required for traditional composting. The optimal two-stage composting and the best quality compost were obtained with 0.30% EWCs and 25% CL.

  1. Photocatalytic removal of SO2 using natural zeolite modified by TiO2 and polyoxypropylene surfactant.

    Science.gov (United States)

    Amini, Nasibeh; Soleimani, Mohsen; Mirghaffari, Nourollah

    2018-01-25

    Air pollution due to emission of various hazardous gases such as SO 2 into the atmosphere and its control is an important environmental issue. Application of photocatalysts is considered as a suitable process to control the gaseous pollutants. In this study, the efficiency of clinoptilolite as a natural zeolite (Ze) modified by TiO 2 (Ze-Ti) and a polymeric surfactant polyoxypropylene (Ze-Ti-POP) for removal of SO 2 was investigated. The nanocomposites were characterized by SEM, EDX, and BET analyses. The photocatalytic oxidation experiments of SO 2 by the nanocomposites and natural zeolite were done under UV irradiation with initial SO 2 concentration of 500 ppm in a photoreactor. The effects of different factors including reaction time, catalyst dose, UV irradiation intensity, humidity content, and calcination temperature and dose of TiO 2 were studied. The modification of clinoptilolite by TiO 2 and POP increased considerably the BET specific surface area of the nanocomposites. The results showed that maximum removal efficiencies of SO 2 by Ze-Ti and Ze-Ti-POP under the optimum experimental conditions were 82.1 and 87.4%, respectively. Adsorption kinetics data well fitted with the Langmuir-Hinshelwood model. Moreover, reusing of nanocomposites after three regeneration cycles indicated that application of Ze-Ti and Ze-Ti-POP nanocomposites could be a promising approach for SO 2 removal. Graphical abstract ᅟ.

  2. Investigation of the mechanism of interaction at the hydrothermal conditions of zeolite – cubic analcime with the Li+, Mg2+, Sr2+ and Fe3+ ions

    Directory of Open Access Journals (Sweden)

    Asta TRAIDARAITĖ

    2013-09-01

    Full Text Available Analcime and clinoptilolite are among the most abundant zeolites in nature. During recent decades natural analcimes and clinoptilolites, also synthetic modified analcimes have been investigated as potential and innovative substances, possible to use for the immobilization of radioactive waste, molecular catalysis and other purposes. However, natural analcimes like many natural rocks are contamined with various impurities (about 30 %, which significally reduces their sorption possibilities and possibilities of their using in such chemical technologies as catalysis, fractioning of hydrocarbons and other. In this article the stability of cubic analcime at the hydrothermal conditions at 180 °C temperature in solutions of various concentrations, containing Li+, Mg2+, Sr2+ and Fe3+ ions has been examined. These processes have big signification for the formation of ion-exchanged analcimes, its sorption properties and also if ions have been immobilized in analcime structure. It has been established, that as result of interaction between cubic analcime and lithium chloride solutions the formation of new compounds: lithium silicate and silinaite occurs. At the same hydrothermal conditions the interaction between cubic analcime and chloride solutions, containing Sr2+, Mg2+ and Fe3+ ions pass without formation of new compounds, and only with interposition of these ions in the structure of cubic analcime. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.1496

  3. Product evaluation phase 1 report

    International Nuclear Information System (INIS)

    Fairhall, G.A.

    1984-01-01

    This report concerns the intermediate-level radioactive waste arisings from the reprocessing of irradiated nuclear fuel at BNFL Sellafield. The site ion exchange effluent plant will remove Cs and Sr from active liquid effluents using Mud Hills clinoptilolite. Approximately 40 to 50 m 3 of spent ion exchanger will be generated each year together with 7.5 m 3 of filter sand. Headings are: introduction; characterisation; initial evaluation of potential matrices for encapsulation of waste in form suitable for disposal; waste simulation. (U.K.)

  4. Influence of Natural Zeolite on Performance of Laying Hens and Egg Quality

    OpenAIRE

    ÖZTÜRK, Ergin; ERENER, Güray; SARICA, Musa

    2014-01-01

    This experiment was conducted to study the effects of natural zeolite on the performance of laying hens. One hundred and eighty 37-week-old Babcock B-300 hens were fed with a diet containing 0, 20, 40, 60 and 80 g clinoptilolite/kg in an experiment consisting of 36 hens per treatment during a 4x28 days experimental period. All feeding programs were isocaloric and isonitrogenous. Hens were put at random into 5 treatment groups (12 replicates and 36 hens per treatment). No significant dietar...

  5. Immobilization and leaching mechanisms of radwaste in cement-based matrices

    International Nuclear Information System (INIS)

    Glasser, F.P.; Rahman, A.A.; Crawford, R.W.; McCullough, C.E.; Angus, M.J.

    1983-01-01

    The effect of potential sorbers including silicas, titania, calcined kaolin, zirconium phosphate and two crystalline calcium silicates, tobermorite and xonotlite, have been used to improve the Cs-retention capacity of cement-based systems. The analysis of the pore fluid compositions of equilibrated cement-radwaste composites provides evidence concerning the leach mechanisms whereby Cs is removed. The reactions occurring between cement and clinoptilolite are elucidated and results of kinetic studies presented. Simulate Magnox waste is shown to react with cement, leading to a carbonate exchange. (author)

  6. Recovery of nutrients from biogas digestate with biochar and clinoptilolite

    NARCIS (Netherlands)

    Kocaturk, N.P.

    2016-01-01

    The liquid fraction of digestate contains nutrients which makes it a valuable fertiliser in agricultural crop production systems. However, direct application of digestate may raise practical and environmental problems. Therefore, processes to concentrate nutrients have been proposed aiming not

  7. The effects of an artificially enhanced clinoptilolite in patients with ...

    African Journals Online (AJOL)

    studies have shown that one to two thirds of subjects with IBS have symptoms that overlap ... This rendering a particle (device), which is more specific for binding intestinal .... Clinical trials in IBS are difficult to design because, unlike other organic disease ... assigned to the 2-week run-in phase of the study to assess baseline ...

  8. Design and characterization of chitosan/zeolite composite films--Effect of zeolite type and zeolite dose on the film properties.

    Science.gov (United States)

    Barbosa, Gustavo P; Debone, Henrique S; Severino, Patrícia; Souto, Eliana B; da Silva, Classius F

    2016-03-01

    Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance.

  9. Radionuclide getters in the near-field chemistry of repositories. Annual report - February 1989

    International Nuclear Information System (INIS)

    Holland, T.R.; Lee, D.J.

    1989-02-01

    A programme of work has commenced to assess the radionuclide sorption efficiency of selected inorganic 'getters' incorporated into sulphate resisting Portland cement; as a means of enhancing the retention of radioactive species by the proposed repository backfill. For this initial study, a limited number of radioisotopes have been selected, with particular reference to those likely to be mobile in an alkaline environment, ie. Ra-266, Cs-134 and I-125. The getters chosen for this stage of the programme were Clinoptilolite, Molecular Sieve 5a, Tobermorite and Ferric Floc. (author)

  10. Decreasing of transfer of caesium and strontium radionuclides from soil to vegetation - Use of modified aluminosilicates for decreasing of transfer of caesium and strontium radionuclides from soil to vegetation

    Energy Technology Data Exchange (ETDEWEB)

    Voronina, Anna V.; Blinova, Marina O.; Semenischev, Vladimir S.; Kutergin, Andrey S. [Ural federal university, 620002 Ekaterinburg (Russian Federation)

    2014-07-01

    The method of addition of sorbents to soils is seemed to be the most efficient for decreasing of transfer of radionuclides from soil to vegetation. Using sorbents should possess affinity to natural systems, high specificity and selectivity and also irreversibility of sorption of radionuclides for effective retention of radionuclides as well as to prevent their migration into vegetation and further movement through food chains. Specificity, selectivity and reversibility of sorption of caesium and strontium radionuclides by natural aluminosilicates (glauconite, clinoptilolite) and modified ferrocyanide sorbents based on them was studied in this work. It was shown that the natural glauconite sorbs caesium from tap water with distribution coefficient K{sub d} = 10{sup (3.5±0.1)} mL/g, static exchange capacity of Cs is 11.0 mg/g; it shows lower specificity to strontium: K{sub d} = 10(2.5±0.1) mL/g, static exchange capacity = 9 mg/g. For clinoptilolite these parameters are for caesium K{sub d} = 10(4.4±0.5) mL/g, static exchange capacity 210 mg/g; for strontium K{sub d} = 10(3.5±0.1) mL/g, capacity = 12 mg/g. Ferrocyanide sorbents concentrate caesium radionuclides more effectively: distribution coefficient of Cs from tap water by mixed nickel-potassium ferrocyanide based on glauconite is 10(5.9±1.6) mL/g, static exchange capacity of Cs is (63.0±2.0) mg/g; for mixed nickel-potassium ferrocyanide based on clinoptilolite these characteristics are respectively 10(7.4±1.3) mL/g, 500 mg/g. In case of modified sorbents specificity to strontium remains the same as for natural aluminosilicates. Reversibility of sorption of caesium by natural glauconite and ferrocyanide sorbent was determined as caesium leaching degree from saturated samples. High caesium leaching rates and degrees are typical for natural glauconite irrespective of leachant salinity: total degree of leaching after 35 days of leaching was: mineral water = 63.4%, tap water = 41.6% and rain water = 28.8%. For

  11. Deposition and diagenesis of the Brushy Basin Member and upper part of the Westwater Canyon member of the Morrison Formation, San Juan Basin, New Mexico

    International Nuclear Information System (INIS)

    Bell, T.E.

    1986-01-01

    The Brushy Basin Member and the upper part of the Westwater Canyon Member of the Morrison Formation in northwest New Mexico are nonmarine sedimentary rocks of Late Jurassic age. This stratigraphic interval consists of as many as four lithofacies deposited in fluvial and playa-lake environments. Lithofacies A is composed of crossbed feldspathic sandstone and was deposited by braided streams on an alluvial plain. Lithofacies B is composed of crossbedded feldspathic sandstone and tuffaceous mudstone, and was deposited by braided and anastomosing streams at the distal end of the alluvial plain. Lithofacies C is composed of calcareous, tuffaceous mudstone and was deposited on a mudflat between the alluvial plain and a playa lake. Lithofacies D is composed of zeolitic, tuffaceous mudstone and was deposited in a playa lake. The distribution of diagenetic facies in mudstones and tuffs in the Brushy Basin Member and upper part of the Westwater Canyon Member reflects the pH and salinity gradients common to fluvial/playa-lake systems. The abundant vitric ash in the sediments reacted to form montmorillonite in the fluvial facies. Calcite and montmorillonite were the reaction products where the fluvial and outermost playa facies met. Vitric ash reacted to form clinoptilolite and heulandite along the playa margins. In the center of the playa facies, analcime replaced clinoptilolite, an early zeolite. These early diagenetic minerals were replaced by albite, quartz, and mixed-layer illitemontmorillonite where the Brushy Basin Member and upper part of the Westwater Canyon Member have been deeply buried in the San Juan basin

  12. Development of early diagenetic silica and quartz morphologies — Examples from the Siri Canyon, Danish North Sea

    DEFF Research Database (Denmark)

    Weibel, Rikke; Friis, Henrik; Kazerouni, Afsoon Moatari

    2010-01-01

    in the following way: 1. Opal rims; characteristic of the initial phase of the silica diagenesis in most sandstone units in the Siri Canyon. Thick opal rims characterise the sandstone parts adjacent to the mudstone units in the Stine segment of the Siri Field. 2. Microquartz (quartz crystals with a size of 1–5 μm......); seen as coatings on the opal rims, both ordered and random. 3. Cavity overgrowth; found as quartz outgrowths in circular and angular cavities formed by dissolution of early authigenic phases. Angular cavities in the microquartz coatings origin from dissolution of clinoptilolite, possibly with a source...

  13. Conditions and processes affecting radionuclide transport

    Science.gov (United States)

    Simmons, Ardyth M.; Neymark, Leonid A.

    2012-01-01

    Characteristics of host rocks, secondary minerals, and fluids would affect the transport of radionuclides from a previously proposed repository at Yucca Mountain, Nevada. Minerals in the Yucca Mountain tuffs that are important for retarding radionuclides include clinoptilolite and mordenite (zeolites), clay minerals, and iron and manganese oxides and hydroxides. Water compositions along flow paths beneath Yucca Mountain are controlled by dissolution reactions, silica and calcite precipitation, and ion-exchange reactions. Radionuclide concentrations along flow paths from a repository could be limited by (1) low waste-form dissolution rates, (2) low radionuclide solubility, and (3) radionuclide sorption onto geological media.

  14. Analysis for the Sorption Kinetics of Ag Nanoparticles on Natural Clinoptilolite

    Directory of Open Access Journals (Sweden)

    Alvaro Ruíz-Baltazar

    2015-01-01

    Full Text Available The kinetic adsorption behavior of silver nanoparticles deposited on a natural zeolite from Oaxaca is presented. Theoretical models as Lagergren first-order, pseudo-second-order, Elovich, and intraparticle diffusion were employed and compared with experimental data obtained by atomic absorption spectrophotometry technique. Correlation factors R2 of the order of 0.99 were observed. Analysis by transmission electron microscopy revealed that the silver nanoparticles were homogeneously distributed on the zeolite. Additionally, chemical characterization of the material was carried out through a dilution process with lithium metaborate. An average value of 9.3 in the Si/Al ratio was observed and related to the kinetic adsorption behavior of the zeolite.

  15. Natural sorptive barriers in Yucca Mountain, Nevada, for long-term isolation of high-level waste

    International Nuclear Information System (INIS)

    Bish, D.L.; Vaniman, D.T.; Rundberg, R.S.; Wolfsberg, K.; Daniels, W.R.; Broxton, D.E.

    1984-01-01

    There are several sorptive phases occurring naturally in the silicic tuffs at Yucca Mountain, Nevada, that can aid in the long-term isolation of high-level wastes. These phases include hydrated volcanic glasses, smectites and zeolites. Los Alamos has a continuing programme to investigate the mineralogy and stratigraphy of the tuffs at Yucca Mountain. In addition, extensive data have been obtained on the sorptive behaviour of technetium, strontium, caesium, barium, cerium, europium, uranium, neptunium, plutonium and americium on the minerals in tuffs. Sorption of elements by ion-exchange processes is high in tuffs containing smectite and the zeolites clinoptilolite-heulandite and mordenite. Moreover, sorption correlates with abundances of these minerals. Sorption is not as high for the zeolite analcime and for volcanic glass. Elements that may not sorb by ion exchange, e.g. plutonium, also tend to be sorbed when the zeolite abundance is high, but the correlations are less clearly defined. Because of the correlation between sorptive capacity and mineralogy, an accurate knowledge of mineral distribution and stratigraphy is essential. The distribution of hydrated glasses is stratigraphically controlled, and the glasses occur in narrow unaltered horizons as vitrophyres and as vitric tuff. Although glasses are of minor importance as sorptive phases, they are very reactive and can alter to other minerals if heated in the presence of water. Smectite clays are reversibly expandable and are widespread in tuffs, but their beneficial properties can be modified by prolonged exposure to elevated temperatures. The zeolites clinoptilolite-heulandite and mordenite occur in high concentrations in silicic tuffs, mostly as secondary alterations of non-welded and poorly welded tuffs; their distribution is therefore stratigraphically controlled

  16. Copper removal and nickel for exchange cationic with a natural zeolite

    International Nuclear Information System (INIS)

    Estupinan, Arnoldy; Sarmiento, Diego; Belalcazar de Galvis, Ana Maria

    1998-01-01

    Natural zeolite clinoptilolite, was used to remove copper and nickel from waste waters of a galvanotechnical company. Exchange capacity determined for the zeolite after its transformation to homoionic sodium form, was 0.794 meq/g for copper and 0.447 meq/g for nickel. There were made batch and column experiments, reaching the last one a better approach to the equilibrium. From the degeneration essays, the sodical zeolite concentrates the copper in the waste waters to 23.5 up times the level found for the acid rinsing waters; it shows its potential use in treatment of these waste, because its effectiveness and low cost

  17. Microautoradiography in studies of Pu(V) sorption by trace and fracture minerals in tuff

    International Nuclear Information System (INIS)

    Vaniman, D.; Furlano, A.; Chipera, S.; Thompson, J.; Triay, I.

    1996-01-01

    Microautoradiography was used to evaluate the mineralogic basis of Pu(V) retention by tuffs from Yucca Mountain, Nevada. Altered orthopyroxenes and oxide minerals are associated with high Pu retention but are limited to specific stratigraphic horizons. A weaker but more general association of Pu with smectite occurs in most samples. Thin-sections that cross fractures allow comparative studies of Pu retention by fracture-lining versus matrix minerals. Using Ag metal in emulsions as a measure of underlying Pu concentration, electron-microprobe analysis can quantify Pu retention along fracture walls and provide mineral/mineral Pu retention factors. For smectite-lined microfractures in zeolitized tuff, the smectite/clinoptilolite Pu retention factor is >80

  18. Environmentally-friendly animal litter

    Science.gov (United States)

    Boxley, Chett; McKelvie, Jessica

    2013-09-03

    An animal litter composition that includes geopolymerized ash particulates having a network of repeating aluminum-silicon units is described herein. Generally, the animal litter is made from a quantity of a pozzolanic ash mixed with an alkaline activator to initiate a geopolymerization reaction that forms geopolymerized ash. This geopolymerization reaction may occur within a pelletizer. After the geopolymerized ash is formed, it may be dried and sieved to a desired size. These geopolymerized ash particulates may be used to make a non-clumping or clumping animal litter or other absorbing material. Aluminum sulfate, clinoptilolite, silica gel, sodium alginate and mineral oil may be added as additional ingredients.

  19. Design and characterization of chitosan/zeolite composite films — Effect of zeolite type and zeolite dose on the film properties

    International Nuclear Information System (INIS)

    Barbosa, Gustavo P.; Debone, Henrique S.; Severino, Patrícia; Souto, Eliana B.; Silva, Classius F. da

    2016-01-01

    Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance. - Highlights: • Zeolite/chitosan composite films were prepared by casting technique. • Micrographs showed slight difference according to the content and A-type zeolite. • The barrier properties of the films were suitable to the dressing application. • Film characterization suggested that zeolites interacted with the chitosan chain.

  20. Design and characterization of chitosan/zeolite composite films — Effect of zeolite type and zeolite dose on the film properties

    Energy Technology Data Exchange (ETDEWEB)

    Barbosa, Gustavo P.; Debone, Henrique S. [Instituto de Ciências Ambientais, Químicas e Farmacêuticas, Universidade Federal de São Paulo, Diadema (Brazil); Severino, Patrícia [Universidade Tiradentes, Instituto de Tecnologia e Pesquisa, Aracaju (Brazil); Souto, Eliana B. [Department of Pharmaceutical Technology, Faculty of Pharmacy, University of Coimbra (FFUC), Pólo das Ciências da Saúde, Azinhaga de Santa Comba, 3000-548, Coimbra (Portugal); Center for Neuroscience and Cell Biology & Institute for Biomedical Imaging and Life Sciences (CNC-IBILI), University of Coimbra, Pólo das Ciências da Saúde, Azinhaga de Santa Comba, 3000-548, Coimbra (Portugal); Silva, Classius F. da, E-mail: cfsilva@unifesp.br [Instituto de Ciências Ambientais, Químicas e Farmacêuticas, Universidade Federal de São Paulo, Diadema (Brazil)

    2016-03-01

    Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance. - Highlights: • Zeolite/chitosan composite films were prepared by casting technique. • Micrographs showed slight difference according to the content and A-type zeolite. • The barrier properties of the films were suitable to the dressing application. • Film characterization suggested that zeolites interacted with the chitosan chain.

  1. The spectroscopic study of building composites containing natural sorbents.

    Science.gov (United States)

    Król, M; Mozgawa, W

    2011-08-15

    This work presents the results of FT-IR spectroscopic studies of heavy metal cations (Ag(+), Pb(2+), Zn(2+), Cd(2+) and Cr(3+)) immobilization from aqueous solutions on natural sorbents. The sorption has been conducted on sodium forms of zeolite (clinoptilolite) and clay minerals (mixtures containing mainly montmorillonite and kaolinite) which have been separated from natural Polish deposit. In the next part of the work both sorbents were used to obtain new building composites. It was proven those heavy metal cations' sorption causes changes in IR spectra of the zeolite and clay minerals. These alterations are dependent on the way the cations were sorbed. In the case of zeolite, variations of the bands corresponding to the characteristic ring vibrations have been observed. These rings occur in pseudomolecular complexes 4-4-1 (built of alumino- and silicooxygen tetrahedra) which constitute the secondary building units (SBU) and form spatial framework of the zeolite. The most significant changes have been determined in the region of pseudolattice vibrations (650-700 cm(-1)). In the instance of clay minerals, changes in the spectra occur at two ranges: 1200-800 cm(-1)--the range of the bands assigned to asymmetric Si-O(Si,Al) and bending Al-OH vibrations and 3800-3000 cm(-1)--the range of the bands originating from OH(-) groups stretching vibrations. Next results indicate possibilities of applying the used natural sorbents for the obtainment of new building materials having favourable composition and valuable properties. The zeolite was used for obtaining autoclaved materials with an addition of CaO, and the clay minerals for ceramic sintered materials with an addition of quartz and clinoptilolite were produced. FT-IR studies were also conducted on the obtained materials. Copyright © 2010 Elsevier B.V. All rights reserved.

  2. High performance nano-titania photocatalytic paper composite. Part II: Preparation and characterization of natural zeolite-based nano-titania composite sheets and study of their photocatalytic activity

    International Nuclear Information System (INIS)

    Ko, Seonghyuk; Fleming, Paul D.; Joyce, Margaret; Ari-Gur, Pnina

    2009-01-01

    A novel paper composite with high photocatalytic performance was fabricated using natural zeolite (clinoptilolite)-based nanosized TiO 2 . Photocatalytic materials, from sol-gel derived TiO 2 colloids to its coupling with zeolite, have been designed, prepared and characterized. As-prepared anatase TiO 2 on zeolite particles were readily used in photocatalytic paper, which revealed zeolite-TiO 2 particles dispersed on a dense network of fibers with microvoids. Natural zeolite-based TiO 2 composite sheets described here decomposed gaseous toluene very effectively after UV irradiation and its removal efficiency was higher than that accomplished by photocatalytic paper made with Degussa P25 TiO 2 or Ahlstrom commercial photocatalytic non-woven paper.

  3. 134cs uptake by plants from soil applying different absorbents

    International Nuclear Information System (INIS)

    Oncsik, M.

    1998-01-01

    A study of isotope uptake by plants using different zeolite clay minerals (montmorillonite, mordenite, clinoptilolite) was started with a view to reducing the rate of isotope uptake by plants by applying additives given to the soil. In pot experiments, the 134 Cs activity of green peas was reduced by 16% in average as compared to the control in the soils enriched with zeolite (mordenite type). Under field conditions, the radioactivity of millet and carrot yields were investigated in soils ameliorated with montmorillonite clay mineral. The radioactive contamination of the yield in soil treated with zeolite was in average 10% lower for millet and 24% for carrot roots as compared to the control

  4. Alteration of basaltic glass in Iceland as a natural analogue for nuclear waste glasses

    International Nuclear Information System (INIS)

    Crovisier, J.L.; Advocat, T.; Fritz, B.; Petit, J.C.

    1989-01-01

    The authors describe the longer term geochemical consequences of basaltic glass dissolution in fresh water at 0 0 C calculated with the computer code DISSOL. The clay minerals were represented by an ideal solid solution model (CISSFIT) able to describe variations in chemical composition of a clay phase in response to variations of the solution chemistry. The predicted mineral phases were iron hydroxides followed by kaolinite, TOT clays, chabazite and clinoptilolite. These results are in reasonably good agreement with experimental results and observations of altered subglacial hyaloclastites from Iceland. The formation of secondary products are mainly controlled by thermodynamic constraints. Kinetic effects, such as diffusion in the near glass surface are not important

  5. Bench-scale treatability studies for simulated incinerator scrubber blowdown containing radioactive cesium and strontium

    International Nuclear Information System (INIS)

    Coroneos, A.C.; Taylor, P.A.; Arnold, W.D. Jr.; Bostick, D.A.; Perona, J.J.

    1994-12-01

    The purpose of this report is to document the results of bench-scale testing completed to remove 137 Cs and 90 Sr from the Oak Ridge K-25 Site Toxic Substances Control Act (TSCA) Incinerator blowdown at the K-25 Site Central Neutralization Facility, a wastewater treatment facility designed to remove heavy metals and uranium from various wastewaters. The report presents results of bench-scale testing using chabazite and clinoptilolite zeolites to remove cesium and strontium; using potassium cobalt ferrocyanide (KCCF) to remove cesium; and using strontium chloride coprecipitation, sodium phosphate coprecipitation, and calcium sulfate coprecipitation to remove strontium. Low-range, average-range, and high-range concentration blowdown surrogates were used to complete the bench-scale testing

  6. Immobilization of radioactive waste in cement-based matrices

    International Nuclear Information System (INIS)

    Glasser, F.P.; Rahman, A.A.; Crawford, R.W.; McCulloch, C.E.; Angus, M.J.

    1984-01-01

    Tobermorite and xonotlite, two synthetic calcium silicate hydrates, improve the Cs retention of cement matrices for Cs, when incorporated at the 6 to 10% level. A kinetic and mechanistic scheme is presented for the reaction of fine grained, Cs-loaded clinoptilolite with cement. The Magnox waste form reacts quickly with cement, leading to an exchange of carbonate between waste form and cement components. Carbonation of cements leads to a marked improvement in their physical properties of Cs retentivity. Diffusion models are presented for cement systems whose variable parameters can readily be derived from experimental measurements. Predictions about scaled-up behaviour of large immobilized masses are applied to extrapolation of laboratory scale results to full-size masses. (author)

  7. Innovative materials in winemaking

    Directory of Open Access Journals (Sweden)

    Luchian Camelia Elena

    2015-01-01

    Full Text Available Wineries have been trying to reduce metallic content of wines by adding various substances. The most used treatment with potassium ferrocyanide causes the elimination of the majority of iron content, together with a significant reduction in the content of other metals. Potassium ferrocyanide also leads to the formation of undesirable hazes. White wines composition and organoleptic properties are influenced by many and diverse factors corresponding to the specific production area, such as grape variety, soil and climate, culture, yeast, winemaking practices and storage. The aim of this research was to investigate variations in metals and volatiles content of Feteasca regală wine samples treated with SBA-15, AlMCM-41, KIT-6 and Clinoptilolite materials with GS-MS and MP-AES.

  8. Conversion of radwaste-loaded zeolites into a borosilicate glass to improve their properties for final disposal (preliminary results)

    International Nuclear Information System (INIS)

    Kazemian, H.; Ghannadi Maraghe, M.; Mallah, M.H.; Firooz Zare, M.; Kooshkestani, R.; Naghavi, S.Sh.

    2002-01-01

    Research was undertaken to fix radioisotopes from simulated nuclear waste streams into durable and stable borosilicate glass matrices based on the conversion of different type of zeolites. It was found that the selectivity of Iranian clinoptilolite and the relevant synthetic zeolite toward cesium and strontium were quite good whereas the leach resistance of the loaded zeolite was relatively poor. To improve the leach resistance of the used zeolites, conversion of the spent exchangers into borosilicate glass was investigated. Results obtained in the non active bench scale tests phase were promising. It is concluded that spent zeolites loaded with radioactive materials can be converted into a durable, high leach resistant borosilicate glass, a proper matrix for final disposal of nuclear waste. (author)

  9. The stability of candidate buffer materials for a low-level radioactive waste repository

    International Nuclear Information System (INIS)

    Torok, J.; Buckley, L.P.; Burton, G.R.; Tosello, N.B.; Maves, S.R.; Blimkie, M.E.; Donaldson, J.R.

    1989-11-01

    Inorganic ion-exchangers, clinoptilolite and clay, will be placed on the floor of a low-level radioactive waste repository to be built at Chalk River Nuclear Laboratories. The stability of these ion-exchange materials for a range of potential chemical environments in the repository was investigated. The leaching of waste forms and concrete and biological activity may create acidic or basic environment. The dissolution mechanisms of the ion exchangers for both acid and alkali conditions were established. Changes in distribution coefficients occurred shortly after the commencement of the treatment and were due to changes in the counter-ion content of the ion exchangers. No evidence was found to suggest gradual selective destruction of exchange sites responsible for the high distribution coefficients observed

  10. Photodynamic dye adsorption and release performance of natural zeolite

    Science.gov (United States)

    Hovhannisyan, Vladimir; Dong, Chen-Yuan; Chen, Shean-Jen

    2017-03-01

    Clinoptilolite type of zeolite (CZ) is a promising material for biomedicine and pharmaceutics due to its non-toxicity, thermal stability, expanded surface area, and exceptional ability to adsorb various atoms and organic molecules into micropores. Using multiphoton microscopy, we demonstrated that individual CZ particles produce two-photon excited luminescence and second harmonic generation signal at femtosecond laser excitation, and adsorb photo-dynamically active dyes such as hypericin and methylene blue. Furthermore, the release of hypericin from CZ pores in the presence of biomolecules is shown, and CZ can be considered as an effective material for drug delivery and controlled release in biological systems. The results may open new perspectives in application of CZ in biomedical imaging, and introducing of the optical approaches into the clinical environment.

  11. Removal of arsenic species from drinking water by Iranian natural and synthetic zeolites

    International Nuclear Information System (INIS)

    Menhaje-Bena, R.; Kazemian, H.; Shahtaheri, S.J.; Ghazi-Khansari, M.

    2003-01-01

    The main objective of this study was to find a relatively inexpensive method for removal of arsenic species from drinking water. The uptake capability of Iron (II) modified natural clinoptilolites and relevant synthetic zeolites A and P was investigated toward inorganic arsenic species from drinking water. Results obtained from sorption experiments, using a batch (static) technique showed that, among the investigated zeolites, modified synthetic zeolite A was the most selective sorbent for removal of arsenate and arsenite from drinking water. Through this study the influencing of factories including temperature, concentration, pH, particle size and interferences was evaluated on removal of arsenic species. The synthetic zeolites and their modified forms were also characterized, using XRD, XRF and thermal analysis techniques. (authors)

  12. Diagramas de eslabilidad de zeolitas. I. Zeolitas en ambientes confinados alcalinos

    Directory of Open Access Journals (Sweden)

    La Iglesia, A.

    1989-12-01

    Full Text Available The stability fieds of zeolites in saline alkaline-lake deposits has been studied. Thermodynamical equilibriums were calculed by ussing a method of stimating the Gibbs free energies of formation of zeolites. We have studied the following stability fields: - Diagram c1inoptilolite-erionite-phillipsite.- Diagram analcime-clinoptilolite-chabazite-erionite-mordenite-phillipsite.- Diagram K-feldspar-zeolites in saline alkaline-lake deposits.The obtained stability diagrams show the influence of silica activity, water activity and alkaline ions activity on equilibrium relationship between analcime and alkalic silicic zeolites, and or feldspar and zeolites. pH influence on the solubility zeolites has been also studied. These results show, at pH below 10, that the most silicic zeolites (clinoptilolite and mordenite are more stable than low silicic ones (analcime and chabazite. However, at pH above 10, the low silicic zeolites are the most stable phases.Se estudia la estabilidad de las zeolitas que aparecen en ambientes confinados salinos. Los cálculos de equilibrio se realizan usando valores de energía libre de Gibbs estimados teóricamente. En este artículo se presentan los siguientes diagramas de estabilidad:- Diagrama clinoptiloita-erionita-phillipsita.- Diagrama aoalcima-clinoptilolita-chabazita-eriooita-mordenita-phillipsita.- Diagrama feldespato potásico-zeolitas depósitos salinos.Los diagramas calculados ponen de manifiesto la influencia de las actividades de los iones alcalinos, alcalinotérreos, agua y sílice en el equilibrio entre las distintas zeolitas y entre estas y el feldespato potásico. Se estudia también la influencia del pH en la solubilidad de las zeolitas. Los resultados obtenidos demuestran que las zeolitas muy silícicas (clinoptilolita y mordenita son las más estables a pH inferiores a 10. Por el contrario, las zeolitas de bajo contenido en sílice (analcima y chabazita son las más estables a pH superiores a 10.

  13. Studies of adsorption and desorption of zinc ions on zeolites by means of 65Zn

    International Nuclear Information System (INIS)

    Foeldesova, M.; Dillinger, P.; Lukac, P.

    2001-01-01

    The uptake of different metals by natural and chemically modified ion-exchangers, including zeolites, were studied in order to minimize the contamination of environment with metals in ionic form. In recent years considerable attention has been devoted to the studies of chemically modified zeolites their properties and applications. The used zeolite originated from the deposit Nizny Hrabovec, eastern Slovakia (NH) and from deposit of Ukraine (U). The zeolite from Slovakia is a clinoptilolite /40 -70%/ type, the zeolite from Ukraine is a mixed mordenite /75%/ and clinoptilolite /25%/ type. A fraction of 1.5 -2.5 mm was separated from the grained zeolite by sieving. The sedimentary zeolites, being the siliceous zeolites, should exhibit substantial non-selectivity for the divalent cations having a high hydration enthalpy , including zinc ( -2026 kJ/g). Zinc is an essential trace element in all-living systems from bacteria to humans. The toxicity of zinc and most of zinc compounds is generally low, however, sometimes industrial and household wastes contain zinc in concentrations, which can be harmful to the environment. The zinc-accompanying impurities, such as cadmium and lead, are of much greater danger .The main source of zinc are waste waters and continuous emission from the production and processing of zinc, other nonferrous smelters, from coal power plants and fossil combustion. The static radio-exchange method using model radioactive solutions was utilized for the determination of the sorption of Zn by the mentioned above zeolitic materials. For this purpose the aqueous solution of 5 · 10 -2 mol dm -3 ZnCl 2 labelled with 65 Zn was used. The areas of application of natural zeolites have been well defined. However, their use can become more efficient after chemical modification. The zeolites acquire new valuable properties, while retaining their original ones. The obtained results make these materials excellent candidates for their potential use for waste water

  14. Environmental applications of natural zeolitic materials based on their ion-exchange properties

    International Nuclear Information System (INIS)

    Colella, C.

    1998-01-01

    Natural zeolites, such as clinoptilolite, chabazite, phillipsite and mordenite, exhibit good selectivities for some water pollutants, e.g., Cs + , NH 4 + and Pb 2+ . Zeolite-rich tuffs may be therefore utilized for removing the above and other cations from wastewaters before discharge. Continuous processes with fixed beds are usually employed for water purification, such as those in service in the U.S.A for ammonium removal from municipal sewage. Direct action of the ion exchanger is needed when the pollutant must be removed from soil and trapped in the zeolite framework. Discontinuous processes (addition of zeolite to the waste solution) are also possible, provided the polluted zeolitic sludge is stabilized-solidified in a cement matrix matrix before disposal. Removal of radionuclides from nuclear power plant waters with natural zeolites is discussed

  15. Colloid facilitated transport in fractured rocks: parameter estimation and comparison with experimental data

    International Nuclear Information System (INIS)

    Viswanthan, H.S.; Wolfsberg, A.V.; Reimus, P.W.; Ware, D.; Lu, G.

    2003-01-01

    Colloid-facilitated migration of plutonium in fractured rock has been implicated in both field and laboratory studies. Other reactive radionuclides may also experience enhanced mobility due to groundwater colloids. Model prediction of this process is necessary for assessment of contaminant boundaries in systems for which radionuclides are already in the groundwater and for performance assessment of potential repositories for radioactive waste. Therefore, a reactive transport model is developed and parameterized using results from controlled laboratory fracture column experiments. Silica, montmorillonite and clinoptilolite colloids are used in the experiments along with plutonium and Tritium. The goal of the numerical model is to identify and parameterize the physical and chemical processes that affect the colloid-facilitated transport of plutonium in the fractures. The parameters used in this model are similar in form to those that might be used in a field-scale transport model

  16. DEVELOPMENT OF A UREA BIOSENSOR BASED ON A POLYMERIC MEMBRANE INCLUDING ZEOLITE

    Directory of Open Access Journals (Sweden)

    M. L HAMLAOUI

    2008-06-01

    + -sensitive membrane is based on a zeolite-incorporated polymeric membrane biosensor (clinoptilolite. The sensitivity of ammonium  detection is sub-nernstian (32mV/pNH4 + but the ISFET presents a high selectivity, which is interesting for measurements in biological media. The grafting of urease to the NH4 +-sensitive membrane was permorfed by cross-linking with glutaraldehyde .The sensitivity of the urea ENFET is 15V/purea and this remains stable over 15 days with a detection limit of 3x10-5 M. Finally, in order to test feasibility of the urea biosensor for environmental applications, the remaining activity of the urease was determined after exposure to enzyme inhibiting heavy metals ions such as Hg(II.Using these urea biosensors, a detection limit of less than 5 x 10-8 M was obtained for Hg(II.

  17. Use of natural zeolites for creation of catalysts containing Cu, Cr, Co, Fe for total oxidation of CO, CH4, CH3OH gas wastes

    International Nuclear Information System (INIS)

    Grigoryan, R.R.; Vartikyan, L.A.; Gharibyan, T.A.; Sargsyan, H.H.

    2006-01-01

    On the basis of natural zeolites of 'Nor Koghb' from Noyemberyan Region of Armenia various quantities of metal containing (Cu,Cr, Co, Fe) catalysts were synthesized by methods of: impregnation; impregnation by ultrasonic treatment (UST); ion exchange. It was studied physico-chemical properties of synthesized catalysts with the help of X-ray, ESR and electronic microscope. Catalytic activity of synthesized catalysts is studied in the processes of deep oxidation by air under atmospheric pressure of methanol, carbon oxide and methane. It is shown that increase of quantity of CuO>2 weight % in clinoptilolite leads to decrease of CO, CH 3 OH and CH 4 conversion and increase of quantity of CoO, Cr 2 O 3 , Fe 2 O 3 (2-6 weight %) leads to increase of above mentioned conversion.These catalysts preserve their catalytic activity for a long period of time

  18. Fracture-lining minerals in the lower Topopah Spring Tuff at Yucca Mountain

    International Nuclear Information System (INIS)

    Carlos, B.A.; Bish, D.L.; Chipera, S.J.

    1991-01-01

    Fracture-lining minerals in the lower Topopah Spring Member of the Paintbrush Tuff at Yucca Mountain, Nevada, are being examined to characterize potential flow paths within and away from the candidate repository horizon. Fracture coatings within this interval can be divided into five categories based on rock matrix and type of fracture. Fracture coatings in the densely welded tuff above the basal vitrophyre, near the candidate repository horizon, include (1) those related to lithophysal cavities; (2) mordenite and manganese oxides on nearly planar fractures; (3) later fracture coatings consisting of zeolites, smectite, and calcite. Fracture-coating minerals in the vitrophyre are fine-grained and consist of smectite and a variety of zeolites. The non- to partially-welded vitric and/or zeolitic stuff below the vitrophyre contains fractures mostly lined by cristobalite and clinoptilolite. 13 refs., 2 figs., 1 tab

  19. Mining run-off gets a treatment

    International Nuclear Information System (INIS)

    Pichon, Max

    2013-01-01

    Full text: Engineering company GHD has implemented an innovative multi- barrier storm water treatment system for a major milling company at the Port of Townsville. The technology economically filters stormwater and is effective for a broad range of contaminants including oil, grease, soluble nutrients and heavy metals. GHD's industrial water and coal seam gas business development leader, Kostas Athanasiadis, created StormDMT, a configuration of inexpensive filter media in a cartridge that cost-effectively removes heavy metals and other dissolved contaminants. He said there was growing recognition of the need to protect receiving waterways and to address water scarcity through measures such as stormwater harvesting. “However, there are few stormwater treatment technologies currently available to effectively and economically remove these contaminants both in particulate and soluble forms, to desirable levels,” he said. GHD carried out a trial at the site in collaboration with the client's engineering, environmental and operational teams. The filter exceeded anticipated performance and the client has adopted a site-wide solution based on the technology. The StormDMT stormwater filter system design incorporates a filtering system (cartridge or other types of filtering configurations) that contains a combination of filter media, including polypropylene flakes to remove oil and grease and particulate-bound contaminants. It also features a zeolite named clinoptilolite to remove positive charged dissolved contaminants such as heavy metals and ammonium nitrogen. Clinoptilolite has been chemically conditioned to maximise its operational ion exchange capacity. Finally, laterite removes negative charged contaminants such as phosphate, nitrate and arsenic as well as heavy metals that have broken through the clinotpilolite layer. One of the key advantages of the StormDMT technology is the low discharge levels it is capable of achieving or dissolved nutrients and

  20. Removal of Radioactive Nuclides by Multi-Functional Microcapsules Enclosing Inorganic Ion-Exchangers and Organic Extractants

    Energy Technology Data Exchange (ETDEWEB)

    Mimura, H.; Akiba, K.; Onodera, Y.

    2002-02-26

    The microcapsules enclosing two kinds of functional materials, inorganic ion-exchangers and organic extractants, were prepared by taking advantage of the high immobilization ability of alginate gel polymer. The fine powders of inorganic ion-exchanger and oil drops of extractant were kneaded with sodium alginate (NaALG) solution and the kneaded sol readily gelled in a salt solution of CaCl2, BaCl2 or HCl to form spherical gel particles. The uptake properties of various nuclides, 137Cs, 85Sr, 60Co, 88Y, 152Eu and 241Am, for thirty-four specimens of microcapsules in the presence of 10-1-10-4 M HNO3 were evaluated by the batch method. The distribution coefficient (Kd) of Cs+ above 103 cm3/g was obtained for the microcapsules enclosing CuFC or AMP. The Kd of Sr2+ around 102 cm3/g was obtained for the microcapsules containing clinoptilolite, antimonic acid, zeolite A, zeolite X or titanic acid. The microcapsules enclosing DEHPA exhibited relatively large Kd values of trivalent metal ions above 103 cm3/g; for example, the Kd values of Cs+, Sr2+, Co2+, Y3+, Eu3+ and Am3+ for a favorable microcapsule (CuFC/clinoptilolite/DEHPA/CaALG) were 1.1x104, 7.5x10, 1.1x10, 1.0x104, 1.4x104, 3.4x103 cm3/g, respectively. The uptake rates of Cs+, Y3+, Eu3+ and Am3+ for this microcapsule were rather fast; the uptake percentage above 90% was obtained after 19 h-shaking and the uptake equilibrium was attained within 1 d. The AMP/CaALG exhibited high uptake ability for Cs+ even after irradiation of 188 kGy, and DEHPA/CaALG microcapsule had similar Kd values of Cs+, Sr2+, Co2+, Y3+, Eu3+ and Am3+ ions before and after irradiation. The microcapsules with various shapes such as spherical, columnar, fibrous and filmy forms were easily prepared by changing the way of dipping kneaded sol into gelling salt solution. The microcapsules enclosing inorganic ion-exchangers and extractants have a potential possibility for the simultaneous removal of various radioactive nuclides from waste solutions.

  1. The role of tailored biochar in increasing plant growth, and reducing bioavailability, phytotoxicity, and uptake of heavy metals in contaminated soil.

    Science.gov (United States)

    Mohamed, Badr A; Ellis, Naoko; Kim, Chang Soo; Bi, Xiaotao

    2017-11-01

    Microwave-assisted catalytic pyrolysis was investigated using K 3 PO 4 and clinoptilolite to enhance biochar sorption affinity for heavy metals. The performance of resulting biochar samples was characterized through their effects on plant growth, bioavailability, phytotoxicity, and uptake of heavy metals in a sandy soil contaminated with Pb, Ni, and Co. The produced biochars have high cation-exchange capacity (CEC) and surface area, and rich in plant nutrients, which not only reduced heavy metals (Pb, Ni, and Co), bioavailability and phytotoxicity, but also increased plant growth rate by up to 145%. The effectiveness of biochar in terms of reduced phytotoxicity and plant uptake of heavy metals was further improved by mixing K 3 PO 4 and clinoptilolite with biomass through microwave pyrolysis. This may be due to the predominance of different mechanisms as 10KP/10Clino biochar has the highest micropore surface area (405 m 2 /g), high concentrations of K (206 g/kg), Ca (26.5 g/kg), Mg (6.2 g/kg) and Fe (11.9 g/kg) for ion-exchange and high phosphorus content (79.8 g/kg) for forming insoluble compounds with heavy metals. The largest wheat shoot length (143 mm) and lowest extracted amounts of Pb (107 mg/kg), Ni (2.4 mg/kg) and Co (63.9 mg/kg) were also obtained by using 10KP/10Clino biochar at 2 wt% load; while the smallest shoot length (68 mm) and highest extracted amounts of heavy metals (Pb 408 mg/kg, Ni 15 mg/kg and Co 148 mg/kg) for the samples treated with biochars were observed for soils mixed with 1 wt% 10Clino biochar. Strong negative correlations were also observed between biochar micropore surface area, CEC and the extracted amounts of heavy metals. Microwave-assisted catalytic pyrolysis of biomass has a great potential for producing biochar with high sorption affinity for heavy metals and rich nutrient contents using properly selected catalysts/additives that can increase microwave heating rate and improve biochar and bio-oil properties

  2. Laboratory studies and model simulations of sorbent material behavior for an in-situ passive treatment barrier

    International Nuclear Information System (INIS)

    Aloysius, D.; Fuhrmann, M.

    1995-01-01

    This paper presents a study combining laboratory experiments and model simulations in support of the design and construction of a passive treatment barrier (or filter wall) for retarding the migration of Sr-90 within a water-bearing surficial sand and gravel layer. Preliminary evaluation was used to select materials for column testing. A one-dimensional finite-difference model was used to simulate the laboratory column results and extrapolation of the calibrated model was then used to assess barrier performance over extended time frames with respect to Sr-90 breakthrough and loading on the filter media. The final results of the study showed that 20 by 50 mesh clinoptilolite will attenuate Sr-90 with a maximum life expentancy of approximately 10 years. This time period is based on allowable limits of Sr-90 activity on the filter media and is also a function of site-specific conditions

  3. Characterization of natural adsorbent material for heavy metal removal in a petrochemical site contamination

    Directory of Open Access Journals (Sweden)

    Bianchi F.

    2013-04-01

    Full Text Available Despite of over 25 years of intensive technological efforts, sub-surface environment cleanup still remains a challenge, especially in case of highly contaminated sites. In this context, ion exchanger technologies could provide simple and effective solutions for heavy metal removal in water treatment. The challenge is finding exchanger able to operate in extreme natural environments or in situations involving natural interfering species such as inorganic ions. In this paper we exam the use of natural zeolites as versatile exchanger for environmental protection of coastal refinery's groundwater against pollution of Ni, Cd, Pb. The influence of particle diameter on clinoptilolite performances toward heavy metal removal is studied. Also, we evaluate the exchanger activities in condition of high ionic strength, commonly present in groundwater located under coastal petrol industries. The obtained results confirmed that ion exchangers could provide an effective solutions for remediation in complex environmental conditions.

  4. A short review of the formation, stability, and cementing properties of natural zeolites

    International Nuclear Information System (INIS)

    Jacobsson, A.

    1977-10-01

    The buffer mass for embedding nuclear waste canisters way down in tunnels or bore holes must fulfil a number of requirements. A 10-15 percent (by weight) sodium bentonite and 85-90 percent quartz mass has been suggested. In most respects this buffer mass has excellent properties but its ion exchange capacity is moderate or low. For this reason zeolites have been suggested as an active component in the mass. The question has been, however, whether zeolites are chemically stable together with other minerals such as montmorillonite which still has to be used to give the buffer mass suitable plastic and permeable properties. It is the main object of this report to illustrate any behaviour of zeolites relevant to the problem of finding a suitable buffer mass. Analcime or analcite, phillipsite, chabazite and clinoptilolite have been suggested as possible components in our buffer mass. (author)

  5. Ion-exchange properties of cesium and strontium into zeolites from sodium salt solutions

    International Nuclear Information System (INIS)

    Kanno, Takuji; Hashimoto, Hiroyuki; Ohtani, Tozo.

    1978-01-01

    The ion-exchange properties of cesium and strontium into zeolite from sodium salt solution has been studied in zeolite A, zeolite X, zeolite Y, mordenite and clinoptilolite. The distribution of cesium into mordenite from about 1 -- 2 M sodium chloride and sodium hydroxide solutions is considerably larger than that into zeolite A. The distribution coefficient for 2 M solution of sodium salts was about 300. Therefore, the separation of cesium from sodium salt solution is possible by using mordenite. The distribution of strontium into zeolites form 1 -- 2 M solutions of sodium chloride and sodium nitrate were in the order of zeolite A>zeolite X>zeolite Y asymptoticaly equals mordenite. The distribution coefficient of 230 was obtained for 1 M solutions of sodium salts. The anion in solutions had no effect on the distribution of cesium and strontium into zeolite from sodium salt solution. (author)

  6. Evaluation of 137Cs sorbents for fixation in concrete

    International Nuclear Information System (INIS)

    Plodinec, M.J.

    1976-01-01

    As part of the long-term waste management program at the Savannah River Laboratory, several 137 Cs sorbents were evaluated for incorporation into concrete. The sorbents studied were: Linde AW-300, AW-500, 13-X, and SK-40; Norton Zeolon 200, 500, and 900; clinoptilolite; and vermiculite. The parameters studied were sorption kinetics, leachability, and compressive strength of the concrete. The best sorbents identified were Linde AW-500 and Norton Zeolon 900. In all tests, these two sorbents performed almost identically; sorption kinetics were acceptable; both strengthened the concrete, and both gave relatively leach-resistant concrete. Vermiculite that had been heated to collapse its lattice around 137 Cs gave the most leach-resistant concrete. However, it sorbed cesium slowly, and the resulting concrete was very weak. When silica gel was added to concrete to react with free calcium, the addition had no effect on cesium leachability

  7. Polymeric compositions for “dry” decontamination of NPP equipment and premises

    International Nuclear Information System (INIS)

    Voronik, N.I.; Toropova, V.V.

    2015-01-01

    In JIPNR – “Sosny” NASB developed decontaminating polymeric compositions based on binder – polyvinyl alcohol solution with active additives such as nitric and borohydrofluoric acids, 1-hydroxyethylidene diphosphonic acid and its salts, detergents and fillers - natural tripoli; tripoli modified by ferrocyanides of nickel and copper; pulverized dolomite modified by manganese oxides, ferrocyanides of nickel and copper; clinoptilolite modified by iron chlorides (III) and calcium sodium phosphate and potassium ferrocyanide; hydrolytic lignin. It is shown that the developed decontaminating polymeric compositions (pastes) possess high decontaminating capacity (FD 102 – 103) and low adhesion to the surfaces of stainless and carbon steels, including painted, plastic, self-leveling floors, teflon-surface. Prolonged leaching method allowed determine the chemical resistance of “dry” decontamination wastes, strength of "1"3"7Cs and "6"0Co fixations in wastes obtained in result of using new decontamination pastes [ru

  8. Research and development regarding the retaining mechanism of lead ions in industrial wastewaters using natural matter with remarkable properties

    Science.gov (United States)

    Pop, A.; Iepure, G.

    2017-05-01

    The paper shows the studying of the retaining mechanism of lead ions in industrial wastewaters through static and dynamic ion exchange mechanisms. In the experimental determinations of the lead metallic ion retention, metallurgical industry wastewaters have been used on samples of volcanic zeolite tuff (from Barsana, Maramures), samples that show a high concentration of lead ions and an acidic pH. The results showed that both the static and the dynamic ion exchanges ended with good results and they were consistent with other studies conducted on clinoptilolite zeolite tuff. Knowing that the industrial sector is an important source of environment pollution and degradation and being aware of what a serious threat the heavy metal pollution is, due to their high toxicity and stability, the experiment may find applicability in different aspects, both in the Maramures mining basing as well as in the worldwide controlling and directing of the polluting processes.

  9. Geological nature of mineral licks and the reasons for geophagy among animals

    Science.gov (United States)

    Panichev, Alexander M.; Popov, Vladimir K.; Chekryzhov, Igor Yu.; Seryodkin, Ivan V.; Sergievich, Alexander A.; Golokhvast, Kirill S.

    2017-06-01

    In this paper, the reasons for geophagy (the eating of rocks by wild herbivores) in two regions of the eastern Sikhote-Alin volcanic belt are considered. The mineralogical and chemical features of the consumed rocks, as well as the geological conditions of their formation, are investigated. A comparative analysis of the mineral and chemical composition of the consumed rocks and the excrement of the animals, almost completely consisting of mineral substances, is carried out. It is established that the consumed rocks are hydrothermally altered rhyolitic tuffs located in the volcanic calderas and early Cenozoic volcano-tectonic depressions. They consist of 30-65 % from zeolites (mainly clinoptilolites) and smectites, possessing powerful sorption properties. According to the obtained data, the main reason for geophagy may be connected with the animals' urge to discard excessive and toxic concentrations of certain elements that are widespread in specific habitats and ingested with forage plants.

  10. Alternative materials for fitting the capsule of radioactive waste storage

    International Nuclear Information System (INIS)

    Cruz, B. de la; Rivas, P.; Hernandez, A.; Marin, C.; Villar, M. V.; Iglesia de la, A.

    1999-01-01

    Phosphate minerals of the apatite group and zeolites (clinoptilolites, mordenite and synthetic are thermally stable, at least up to a six-month period at 200 degree centigree. Both materials have a low distribution coefficient (Rd), which increases significantly when impurities like iodides, chlorides and most of the sulphates are eliminated. The adsorption capacity of the impurity-free phosphates is low, since 70 to 90% of the adsorbed I- in the sorption tests is retained. This implies that most of the adsorbed radionuclides would be retained. The impurity-rich phosphates have low thermal conductivity, good compaction capacity and they do not produce much dust. The porosity and bulk density of phosphates and zeolites are constant as the temperature and heating period increase. The superficial area tends to increase as temperature increases from 100 degree centigree to 150 degree centigree, through no important variations are observed when the temperature reaches 200 degree centigree or the heating period is extended from 3 to 12 months. (Author)

  11. Kinetics of silica-phase transitions

    International Nuclear Information System (INIS)

    Duffy, C.J.

    1993-07-01

    In addition to the stable silica polymorph quartz, several metastable silica phases are present in Yucca Mountain. The conversion of these phases to quartz is accompanied by volume reduction and a decrease in the aqueous silica activity, which may destabilize clinoptilolite and mordenite. The primary reaction sequence for the silica phases is from opal or glass to disordered opal-CT, followed by ordering of the opal-CT and finally by the crystallization of quartz. The ordering of opal-CT takes place in the solid state, whereas the conversion of opal-CT takes place through dissolution-reprecipitation involving the aqueous phase. It is proposed that the rate of conversion of opal-CT to quartz is controlled by diffusion of defects out of a disordered surface layer formed on the crystallizing quartz. The reaction rates are observed to be dependent on temperature, pressure, degree of supersaturation, and pH. Rate equations selected from the literature appear to be consistent with observations at Yucca Mountain

  12. Silica Deposition on the Leaves of Mir- and Earth-Grown Super Dwarf Wheat

    Science.gov (United States)

    Campbell, William F.; Bubenheim, David L.; Salisbury, Frank B.; Bingham, Gail E.; McManus, William R.; Biesinger, H. D.; Strickland, D. T.; Levinskikh, Maragarita; Sytchev, Vladimir N.; Podolsky, Igor

    2000-01-01

    Scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) microanalysis were used to investigate the nature of crystals deposited on leaves of Mir- and Earth-grown Super Dwarf wheat (Triticum aestivum L.) plants. Leaves from these plants exhibited dense and uniformly distributed crystals on leaf abaxial surfaces when viewed by SEM. Young leaves showed that crystals initially accumulated around the stomata on the adaxial surface, but became more dense and uniformly distributed as the leaves aged. EDX microanalyses of the Balkanine (a nutrient charged clinoptilolite zeolite) medium in which the wheat plants were grown showed an elemental pattern similar to that observed on the wheat leaves. The absence of N and P in the Balkanine suggests that they were completely utilized by the plants. Only Si and O were evident in the drying agent, Sorb-it-Silica (trademark), and perhaps could have accounted for some of the Si observed on the plant tissue.

  13. Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

    Science.gov (United States)

    Franus, Małgorzata; Jozefaciuk, Grzegorz; Bandura, Lidia; Lamorski, Krzysztof; Hajnos, Mieczysław; Franus, Wojciech

    2016-01-01

    An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite) with used motor oil (1 wt %–8 wt %) caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP), microtomography (MT), and scanning electron microscopy. Maximum porosity was produced at low (1%–2%) oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT) pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms. PMID:28773964

  14. Modification of Lightweight Aggregates’ Microstructure by Used Motor Oil Addition

    Directory of Open Access Journals (Sweden)

    Małgorzata Franus

    2016-10-01

    Full Text Available An admixture of lightweight aggregate substrates (beidellitic clay containing 10 wt % of natural clinoptilolite or Na-P1 zeolite with used motor oil (1 wt %–8 wt % caused marked changes in the aggregates’ microstructure, measured by a combination of mercury porosimetry (MIP, microtomography (MT, and scanning electron microscopy. Maximum porosity was produced at low (1%–2% oil concentrations and it dropped at higher concentrations, opposite to the aggregates’ bulk density. Average pore radii, measured by MIP, decreased with an increasing oil concentration, whereas larger (MT pore sizes tended to increase. Fractal dimension, derived from MIP data, changed similarly to the MIP pore radius, while that derived from MT remained unaltered. Solid phase density, measured by helium pycnometry, initially dropped slightly and then increased with the amount of oil added, which was most probably connected to changes in the formation of extremely small closed pores that were not available for He atoms.

  15. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Mitchell, S.J.; Freeman, H.D.; Buelt, J.L.

    1986-01-01

    Pacific Northwest Laboratory is developing sorbent materials to prevent the migration of radionuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Screening studies identified promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent, adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt %), activated charcoal (6 wt %), synthetic zeolite (20 wt %), and soil (73 wt %) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 2 refs., 6 figs., 3 tabs

  16. Investigation of mircroorganisms colonising activated zeolites during anaerobic biogas production from grass silage.

    Science.gov (United States)

    Weiss, S; Zankel, A; Lebuhn, M; Petrak, S; Somitsch, W; Guebitz, G M

    2011-03-01

    The colonisation of activated zeolites (i.e. clinoptilolites) as carriers for microorganisms involved in the biogas process was investigated. Zeolite particle sizes of 1.0-2.5mm were introduced to anaerobic laboratory batch-cultures and to continuously operated bioreactors during biogas production from grass silage. Incubation over 5-84 days led to the colonisation of zeolite surfaces in small batch-cultures (500 ml) and even in larger scaled and flow-through disturbed bioreactors (28 l). Morphological insights were obtained by using scanning electron microscopy (SEM). Single strand conformation polymorphism (SSCP) analysis based on amplification of bacterial and archaeal 16S rRNA fragments demonstrated structurally distinct populations preferring zeolite as operational environment. via sequence analysis conspicuous bands from SSCP patterns were identified. Populations immobilised on zeolite (e.g. Ruminofilibacter xylanolyticum) showed pronounced hydrolytic enzyme activity (xylanase) shortly after re-incubation in sterilised sludge on model substrate. In addition, the presence of methanogenic archaea on zeolite particles was demonstrated. Copyright © 2010 Elsevier Ltd. All rights reserved.

  17. Recovery of the heavy elements by NaY AND NaZSM-5 sorbant materials

    International Nuclear Information System (INIS)

    Nibou, D.; Lebail, S.

    1997-04-01

    Porous sorbants as zeolites have a several applications in differents fiels: industrial gas purification, catalysis, transformation hydrocarbures prosesses and exchange ions. The hiogh capacity to exchange their cations with those of aqueous solutions was known (1). Since the accession of synthetic zeolites, these silicates have invaded the market and the firstindustrial applications were in exchange field. Studies at Battelle Northwest in Rchland, Washington have shown that zeolites may be used in treatment of radioactive wastes (2). The used method for storing the isotopes is based on selective removal by ion exchange. Clinoptilolite, zeolite (modernite), NaA, and AW-500 have been used. In this context, the present work deals with the recovery of heavy metals like lead and uranium using some microporous materials. The obtained results show that NaY faujasite and NaZSM-5 of the FAU- and MFI-type structure respectively are very effective in removing these elements from waste water

  18. Na-noparticles of activated natural zeolite on textiles for protection and therapy

    Directory of Open Access Journals (Sweden)

    Ivančica Kovaček

    2009-10-01

    Full Text Available Activated natural zeolite clinoptilolite is microporous hydrated aluminosilicates crystals with well-defined structures containing AlO4 and SiO4 tetrahedral linked through the common oxygen atoms. It is to point out that zeolites act as strong adsorbents and ion-exchangers but having many other useful properties. Due to its cationexchange ability, zeolites have catalytic properties and, for that, multiple uses in medicine and industry, agriculture, water purification and detergents. Zeolites are nontoxic substance, excellent for UVR and microbes protection, for proteins and small molecules such as glucose adsorption. In this paper its positive effect on the metabolism of living organisms and its anticancerogenic, antiviral, antimetastatic and antioxidant effect. The activity of natural zeolite as natural immunostimulator was presented as well as its help in healing wounds. Therefore, the present paper is an attempt to modify cotton (by mercerization and polyester (by alkaline hydrolysis fabrics for summer clothing with addition of natural zeolite nanoparticles for achieving UV and antibacterial protective textiles

  19. Batch-wise adsorption, saxs and microscopic studies of zeolite pelletized with biopolymeric alginate

    Directory of Open Access Journals (Sweden)

    E. Chmielewská

    2011-03-01

    Full Text Available Removal of nitrates, sulfate and Zn(II ions from aqueous solutions through adsorption onto biopolymeric alginate/clinoptilolite-rich tuff pellets was studied by using an equilibrium batch technique. The idea of this approach of biosorbent fabrication is to promote the native zeolite adsorption performance and thus to prepare more efficient amphoteric tailor-made products for specific environmental targets. A flexible component, i.e., alginate biopolymer, and a rigid component (pulverized zeolite were crosslinked using Fe(III and Ca(II chlorides, additively. The extent of adsorption was found to be considerably higher than with the other mostly natural adsorbents examined towards similar pollutants. The equilibrium adsorption data for the above pollutants were satisfactorily fitted to Freundlich and Langmuir isotherms, respectively. According to the linscale SAXS pattern, there was a strong background visible, which may indicate the presence of a considerable amount of biopolymeric phase in the composite samples analysed. Scanning Tunneling, Electron and Atomic Force Microscopies helped visualize their surface texture and morphology.

  20. Geochemical and petrographic investigation of Himmetoglu oil shale field, Goynuk, Turkey

    Energy Technology Data Exchange (ETDEWEB)

    Sener, M.; Gundogdu, M.N. [General Directorate of Mineral Research and Exploration, Ankara (Turkey)

    1996-09-01

    The Himmetoglu field is a good example of oil shale fields in Turkey. Mineral and maceral types show that the huminite and liptinite groups tend to be associated with smectite, clinoptilolite and calcite in Himmetoglu oil shale, while the liptinite group is accompanied by analcime and dolomite in bituminous laminated marl. The pH value increases from bottom (pH {lt} 9) to top (pH {gt} 9) in the Himmetoglu formation and volcanogenic materials have played a very important role in deposition of organic matter. The negative correlation between trace elements and organic carbon suggests absence of enrichment of trace elements in oil shales. The results of g.c.-m.s. and carbon isotope analysis show that there is a decrease in the amount of terrestrial organic matter and a relative decrease in maturity of the organic matter in the vertical succession from Himmetoglu oil shape up to the bituminous laminated marl. 8 refs., 6 figs., 5 tabs.

  1. Geological nature of mineral licks and the reasons for geophagy among animals

    Directory of Open Access Journals (Sweden)

    A. M. Panichev

    2017-06-01

    Full Text Available In this paper, the reasons for geophagy (the eating of rocks by wild herbivores in two regions of the eastern Sikhote-Alin volcanic belt are considered. The mineralogical and chemical features of the consumed rocks, as well as the geological conditions of their formation, are investigated. A comparative analysis of the mineral and chemical composition of the consumed rocks and the excrement of the animals, almost completely consisting of mineral substances, is carried out. It is established that the consumed rocks are hydrothermally altered rhyolitic tuffs located in the volcanic calderas and early Cenozoic volcano-tectonic depressions. They consist of 30–65 % from zeolites (mainly clinoptilolites and smectites, possessing powerful sorption properties. According to the obtained data, the main reason for geophagy may be connected with the animals' urge to discard excessive and toxic concentrations of certain elements that are widespread in specific habitats and ingested with forage plants.

  2. Provenance analysis and thermo-dynamic studies of multi-type Holocene duricrusts (1700 BC) in the Sua Salt Pan, NE Botswana

    Science.gov (United States)

    Dill, Harald G.; Dohrmann, R.; Kaufhold, S.; Techmer, A.

    2014-08-01

    Multi-type duricrusts, composed of silcretes, calcretes, halcretes and sulcretes developed during the Holocene at the northern rim of the Sua Salt Pan, NE Botswana. They were investigated for their light (quartz/chalcedony, feldspar, analcime, clinoptilolite, calcite, kaolinite/halloysite, illite-smectite mixed-layers, halite) and heavy minerals (baryte, clinozoisite-epidote s.s.s., amphibole, corundum, tourmaline, ilmenite, rutile, sphene, kyanite, andalusite, staurolite, garnet, zircon, apatite, monazite, cassiterite, garnet, biotite) using petrographic microscopy, X-ray fluorescence and diffraction analyses, radio-carbon dating, scanning electron microscopy equipped with an EDX-system, cation exchange capacity and infrared spectroscopy. Detrital minerals predominantly derived from the erosion of rocks belonging to the Archaean Basement Complex, the Stormberg Volcanites and the Kalahari sediments. Of particular interest to exploration geologists, geikielite-enriched ilmenite fragments are a hint to kimberlitic pipes. Biodetritus was derived from invertebrates and from vertebrates (fish bones?). A man-made impact on the heavy mineral suite has to be invoked from small fragments of cassiterite fragments that derived from processing of sulfidic and pegmatitic Sn-bearing ore. In the salt-pan-derived duricrusts mainly the aeolian and to a lesser degree fluvial inputs were responsible for the concentration of clasts in these multi-type duricrusts. Moreover, their variegated mineralogy enables us to constrain the physical-chemical regime, prevalently as to the pH and the chemical composition of the major constituents. All duricrusts developed in a self-sufficient chemically closed system where quartz and feldspar provided the elements Si, Na, K, Ca, and Ba to produce the encrustations. The spatial and temporal trend in the Sua Salt Pan rim encrustations may be described as follows: (1) sulcrete-silcretes, (2) silcretes with kaolinite-group minerals towards more recent

  3. Isotherms and kinetics of lead and cadmium uptake from the waste leachate by natural and modified clinoptilolite

    Directory of Open Access Journals (Sweden)

    Maryam Faraji

    2012-01-01

    Conclusions: The modified zeolite with surfactant can be used as an appropriate adsorbent for the separation of heavy metals from waste Leachate. Lead and cadmium were absorbed in a single layer on the surface of the modified zeolite with surfactant, comparing different isoterm models, indicated that the capacity of the modified zeolite for lead adsorption was more than cadmium adsorption, but cadmium was absorbed with higher energy.

  4. Increasing levels of zeolite and Yucca schidigera in diets for adult cats

    Directory of Open Access Journals (Sweden)

    Natália Charleaux Roque

    2011-11-01

    Full Text Available The effect of the additives Yucca schidigera (YSC and zeolite (clinoptilolite on digestibility, fecal texture and odor, blood parameters and urine pH of domesticated felines was evaluated. The experiment was conducted in a randomized block design, with twenty-one cats, in two periods, distributed in seven treatments: moist commercial feed (control; control + 125, 250 and 375 ppm YSC; and control + 0.5; 0.75 and 1.0 % zeolite. No differences were observed between the diets regarding apparent digestibility coefficients of nutrient, energy, urine pH or blood parameters. However, levels of 0.5 and 0.75% zeolite were effective both in reducing odor (R² = 96.39 and for fecal texture (R² = 99.63, showing a quadratic pattern for these variables. Levels of 125 and 375 ppm YSC were also efficient in reducing fecal odor; however they did not adjust to regression. Levels of 0.5% and 0.75% zeolite significantly reduce odor of feces and increase fecal texture when added to commercial feed for cats.

  5. Synthesis of high capacity cation exchangers from a low-grade Chinese natural zeolite

    International Nuclear Information System (INIS)

    Wang Yifei; Lin Feng

    2009-01-01

    The Chinese natural zeolite, in which clinoptilolite coexists with quartz was treated hydrothermally with NaOH solutions, either with or without fusion with NaOH powder as pretreatment. Zeolite Na-P, Na-Y and analcime were identified as the reacted products, depending on the reaction conditions such as NaOH concentration, reaction time and hydrothermal temperature. The products were identified by X-ray diffraction, and characterized by Fourier transform IR and ICP. With hydrothermal treatment after fusion of natural zeolite with NaOH, high purity of zeolite Na-Y and Na-P can be selectively formed, their cation exchange capacity (CEC) are 275 and 355 meq/100 g respectively, which are greatly higher than that of the natural zeolite (97 meq/100 g). Furthermore, the ammonium removal by the synthetic zeolite Na-P in aqueous solution was also studied. The equilibrium isotherms have been got and the influence of other cations present in water upon the ammonia uptake suggested an order of preference Ca 2+ > K + > Mg 2+ .

  6. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Mitchell, S.J.; Freeman, H.D.; Buelt, J.L.

    1987-01-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is developing sorbent materials to prevent the migration of radionuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Screening studies identified promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite of clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent, adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 2 references, 6 figures, 3 tables

  7. Evolution in performance assessment modeling as a result of regulatory review

    Energy Technology Data Exchange (ETDEWEB)

    Rowat, J.H.; Dolinar, G.M.; Stephens, M.E. [AECL Chalk River Labs., Ontario (Canada)] [and others

    1995-12-31

    AECL is planning to build the IRUS (Intrusion Resistant Underground Structure) facility for near-surface disposal of LLRW. The PSAR (preliminary safety assessment report) was subject to an initial regulatory review during mid-1992. The regulatory authority provided comments on many aspects of the safety assessment documentation including a number of questions on specific PA (Performance Assessment) modelling assumptions. As a result of these comments as well as a separate detailed review of the IRUS disposal concept, changes were made to the conceptual and mathematical models. The original disposal concept included a non-sorbing vault backfill, with a strong reliance on the wasteform as a barrier. This concept was altered to decrease reliance on the wasteform by replacing the original backfill with a sand/clinoptilolite mix, which is a better sorber of metal cations. This change lead to changes in the PA models which in turn altered the safety case for the facility. This, and other changes that impacted performance assessment modelling are the subject of this paper.

  8. Silicate diagenesis in deep-sea sediments from the Tonga fore-arc (SW Pacific): a strontium and rare earth elements signature

    International Nuclear Information System (INIS)

    Vitali, F.; Stille, P.; Blanc, G.; Toulkeridis, T.

    2000-01-01

    87 Sr/ 86 Sr isotopic ratios, strontium and Rare Earth Element concentrations obtained on volcano-sedimentary rocks and separated clay mineral and zeolite fractions reveal a formation by pore water-volcanic rock interaction for most of the hydrous silicate minerals of the Site 841 ODP collected from the Tonga fore-arc. Unusual strontium concentrations and isotopic ratios recorded in the Miocene tuffs associated with specific REE patterns indicate that the formation of these hydrous silicates does not follow a simple burial diagenesis model, but was related to the cooling of intruding basaltic sills in the Miocene volcano-sedimentary series. Migration of strontium into the pore water in response to the heat flow induced the formation of Sr-bearing zeolites such as clinoptilolite, heulandite and chabazite. No evidence of any influence of a further thermal pulse in the Eocene rhyolitic tuffs could be found. As recorded by the chemistry of their clay mineral fraction, the rhyolitic tuffs developed a polyphasic diagenetic process, which might have been influenced by a possible circulation of a fluid into structurally weak areas. (authors)

  9. Engineered sorbent barriers for low-level waste disposal.

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Mitchell, S.J.; Buelt, J.L.

    1986-12-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is investigating sorbent materials to prevent the migration of soluble radio nuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Laboratory studies identifield promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent and was adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and local soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow-land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 7 refs., 14 figs., 12 tabs.

  10. Engineered sorbent barriers for low-level waste disposal

    International Nuclear Information System (INIS)

    Freeman, H.D.; Mitchell, S.J.; Buelt, J.L.

    1986-12-01

    The Engineered Sorbent Barriers Program at Pacific Northwest Laboratory is investigating sorbent materials to prevent the migration of soluble radio nuclides from low-level waste sites. These materials would allow water to pass, preventing the bathtub effect at humid sites. Laboratory studies identifield promising sorbent materials for three key radionuclides: for cesium, greensand; for cobalt, activated charcoal; and for strontium, synthetic zeolite or clinoptilolite. Mixtures of these sorbent materials were tested in 0.6-m-diameter columns using radioactive leachates. To simulate expected worst-case conditions, the leachate solution contained the radionuclides, competing cations, and a chelating agent and was adjusted to a pH of 5. A sorbent barrier comprised of greensand (1 wt%), activated charcoal (6 wt%), synthetic zeolite (20 wt%), and local soil (73 wt%) achieved the decontamination factors necessary to meet the regulatory performance requirements established for this study. Sorbent barriers can be applied to shallow-land burial, as backfill around the waste or engineered structures, or as backup to other liner systems. 7 refs., 14 figs., 12 tabs

  11. Thermal expansion of ceramic samples containing natural zeolite

    Science.gov (United States)

    Sunitrová, Ivana; Trník, Anton

    2017-07-01

    In this study the thermal expansion of ceramic samples made from natural zeolite is investigated. Samples are prepared from the two most commonly used materials in ceramic industry (kaolin and illite). The first material is Sedlec kaolin from Czech Republic, which contains more than 90 mass% of mineral kaolinite. The second one is an illitic clay from Tokaj area in Hungary, which contains about 80 mass% of mineral illite. Varying amount of the clay (0 % - 50 %) by a natural zeolite from Nižný Hrabovec (Slovak Republic), containing clinoptilolite as major mineral phase is replaced. The measurements are performed on cylindrical samples with a diameter 14 mm and a length about 35 mm by a horizontal push - rod dilatometer. Samples made from pure kaolin, illite and zeolite are also subjected to this analysis. The temperature regime consists from linear heating rate of 5 °C/min from 30 °C to 1100 °C. The results show that the relative shrinkage of ceramic samples increases with amount of zeolite in samples.

  12. Mineralogy of drill holes J-13, UE-25A No. 1, and USW G-1 at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Bish, D.L.; Chipera, S.J.

    1986-09-01

    The mineralogy of drill holes J-13, UE-25A No. 1, and USW G-1 was previously determined using qualitative and semiquantitative techniques, and most of the available data were neither complete nor accurate. New quantitative x-ray diffraction data were obtained for rocks from all three of these drill holes at Yucca Mountain, Nevada. These quantitative analyses employed both external and internal standard x-ray powder diffraction methods and permitted the precise determination of all phases commonly found in the tuffs at Yucca Mountain, including glass and opal-CT. These new data supplant previous analyses and include numerous additional phases. New findings of particular importance include better constraints on the distribution of the more soluble silica polymorphs, cristobalite and opal-CT. Opal-CT was associated solely with clinoptilolite-bearing horizons, and cristobalite disappearance coincided with the appearance of analcime in USW G-1. Unlike previous analyses, we identified significant amounts of smectite in drill hole J-13. We found no evidence to support previous reports of the occurrence of erionite or phillipsite in these drill holes

  13. Removal of lead from aqueous solutions by using the natural and Fe(III)-modified zeolite

    International Nuclear Information System (INIS)

    Kragović, Milan; Daković, Aleksandra; Sekulić, Živko; Trgo, Marina; Ugrina, Marin; Perić, Jelena; Gatta, G. Diego

    2012-01-01

    In the present study, the sorption of lead by the natural and Fe(III)-modified zeolite (clinoptilolite) is described. The characterization of the natural zeolite-rich rock and the Fe(III)-modified form was performed by chemical analysis, point of the zero charge (pH pzc ), X-ray powder diffraction, applying the Rietveld/RIR method for the quantitative phase analysis, and scanning electron microscopy. The effects of sorbents dose and the initial lead concentrations on its sorption by two sorbents were investigated. For both sorbents, it was determined that at lower initial concentrations of lead, ion exchange of inorganic cations in zeolites with lead, together with uptake of hydrogen dominated, while at higher initial lead concentrations beside these processes, chemisorption of lead occurred. Significantly higher sorption of lead was achieved with Fe(III)-modified zeolite. From sorption isotherms, maximum sorbed amounts of lead, under the applied experimental conditions, were 66 mg/g for the natural and 133 mg/g for Fe(III)-modified zeolite. The best fit of experimental data was achieved with the Freundlich model (R 2 ≥ 0.94).

  14. Physical-chemical hydrodynamics of the processes of sorption-membrane technology of LRW treatment

    International Nuclear Information System (INIS)

    Alexander D Efanov; Pyotr N Martynov; Yuri D Boltoev; Ivan V Yagodkin; Nataliya G Bogdanovich; Sergey S Skvortsov; Alexander R Sokolovsky; Elena V Ignatova; Gennady V Grigoriev; Vitaly V Grigorov

    2005-01-01

    tripolite and clinoptilolite of radionuclides 137 Cs and 90 Sr and other from liquid radioactive waste; -the parameter values of tripolite and clinoptilolite coagulation and sedimentation processes under the LRW free convection conditions; - the specific features of the spatial distribution of the pressure micro-fluctuations of LRW flow being passed through the porous system 'nano-structured membrane substrate' in the filtration conditions and in the course of the membrane surface cleaning from cake. The above investigation results have been obtained on a model liquid waste sorption-membrane cleaning test facility. The test facility is unique in that its tanks are manufactured of transparent polycarbonate and do not yield to stain steel tanks in strength. This means that the physical-chemical hydrodynamics of the all processes of the sorption-membrane technology is visualized and can be represented in the evolution of the processes including abnormal conditions. (authors)

  15. The Effect of Zeolite on Aggregate Stability Indices

    Directory of Open Access Journals (Sweden)

    F. Sohrab

    2016-02-01

    Full Text Available Introduction: Soil structural stability affects the profitability and sustainability of agricultural systems. Particle size distribution (PSD and aggregate stability are the important characteristics of soil. Aggregate stability has a significant impact on the development of the root system, water and carbon cycle and soil resistance against soil erosion. Soil aggregate stability, defined as the ability of the aggregates to remain intact when subject to a given stress, is an important soil property that affects the movement and storage of water, aeration, erosion, biological activity and growth of crops. Dry soil aggregate stability (Mean Weight Diameter (MWD, Geometric Mean Diameter (GMD and Wet Aggregate Stability (WAS are important indices for evaluating soil aggregate stability.To improve soil physical properties, including modifying aggregate, using various additives (organic, inorganic and chemicals, zeolites are among what has been studied.According to traditional definition, zeolites are hydratealuminosilicates of alkaline and alkaline-earth minerals. Their structure is made up of a framework of[SiO4]−4 and [AlO4]−5 tetrahedron linked to each other's cornersby sharing oxygen atoms. The substitution of Si+4 by Al+3 intetrahedral sites results inmore negative charges and a high cation exchange capacity.Zeolites, as natural cation exchangers, are suitable substitutes to remove toxic cations. Among the natural zeolites,Clinoptilolite seems to be the most efficient ion exchanger and ion-selective material forremoving and stabilizing heavy metals.Due to theexisting insufficient technical information on the effects of using different levels of zeolite on physical properties of different types of soils in Iran, the aim of this research was to assess the effects of two different types of zeolite (Clinoptilolite natural zeolite, Z4, and Synthetic zeolite, A4 on aggregate stability indicesof soil. Materials and Methods: In this study at first

  16. REMOCIÓN DE MICROORGANISMOS PATÓGENOS PRESENTES EN UN LICOR MIXTO BAJO CONDICIONES DE LABORATORIO EMPLEANDO FILTROS EMPACADOS EN ZEOLITA NATURAL REMOVAL OF PATHOGENIC MICROORGANISMS PRESENT IN MIXED LIQUOUR UNDER LABORATORY CONDITIONS BY USING FILTERS PACKED IN NATURAL ZEOLITE

    Directory of Open Access Journals (Sweden)

    Diana Rocío Acevedo Cifuentes

    2012-12-01

    Full Text Available En este artículo, se presentan los resultados obtenidos en la remoción de coliformes totales, coliformes fecales y salmonella-shigella, presentes en un licor mixto proveniente de la planta de tratamiento de aguas residuales San Fernando (Medellín, Colombia, mediante el uso de una batería de filtros empacados en zeolita clinoptilolita. La experimentación se desarrolló bajo condiciones controladas de caudal y pH, a temperatura ambiente. Se empleó zeolita natural tipo clinoptilolita la cual se activó con solución salina y secado, se empacó en una batería compuesta por dos filtros, uno de flujo descendente y otro de flujo ascendente, para facilitar el contacto de la solución contaminada y el material adsorbente (zeolita. Se realizaron cinco ensayos independientes y al final de cada uno de ellos se lavó y se activó el material zeolítico antes de comenzar el siguiente. En cada ensayo se tomaron tres muestras. Se encontró que la eficiencia de los filtros bajo las condiciones específicas de diseño fue significativamente alta en la remoción de los patógenos evaluados, y el porcentaje de remoción fue independiente del valor de la concentración a la entrada del filtro. Además, la eficiencia en la remoción de los patógenos evaluados no dependió del tipo de microorganismo.This article displays results obtained when total coliforms, fecal coliforms, and Salmonella shigella were removed from mixed liquor taken from San Fernando waste water treatment plant in Medellín, Colombia, by using a battery of filters packed in zeolite clinoptilolite. Experiments were developed under controlled conditions of flow and pH at room temperature. Natural clinoptilolite-type zeolite was used activated with saline solution and drying; it was packed in a battery consisting of two filters (a downward-flow filter and an upward-flow filter in order to make contact of contaminated solution and adsorbent material (zeolite easier. Five independent tests were

  17. POTASSIUM PERMANGANATE AND CLINOPTILOLITE ZEOLITE FOR IN SITU TREATMENT OF GROUND WATER CONTAMINATED WITH LANDFILL LEACHATE: LABORATORY STUDY

    Science.gov (United States)

    There are tens of thousands of closed landfills in the United States, many of whicih are unlined and sited on alluvial deposits. Landfills are of concern because leachate contains a variety of pollutants that can contaminate ground and surface water. Data from chemical analysis...

  18. Comparison of Granular Activated Carbon, Natural Clinoptilolite Zeolite, and Anthracite Packed Columns in Removing Mercury from Drinking Water

    Directory of Open Access Journals (Sweden)

    Mohammad Taghi Samadi

    2010-01-01

    Full Text Available Development of effective methods for the removal of such pollutants as heavy metals (e.g., mercury from surface and ground water resources introduced by municipal and industrial wastewaters seems to be inevitable, especially in the face of the importance of water reuse in combating water shortages, limited availability of water resources, and imminent risks of a water crisis in Iran. A number of methods are already available for the removal of mercury from water resources. However, these techniques must be investigated for their practicability and economy, in addition to their not only effectiveness. In this research, granular activated carbon, natural zeolite, and anthracite packed-columns were investigated as cheap and effective adsorbents for the removal of mercury. Moreover, the effects of changes in pH (6-8, influent mercury concentrations (0.25, 0.5, 0.75, and 1 ppm, contact time (0.5, 1, 2, 3 hr were investigated. Mercury concentration in the samples was determined using a ditizon indicator and spectrophotometry at 492 nm. Results showed that decreasing influent mercury concentration from 1 ppm to 0.25 ppm (under constant conditions increased the removal efficiencies of anthracite, granular activated carbon, and zeolite columns from22%, 63%, and 55% to 28%, 72%, and 64%, respectively. Increasing contact time from 0.5 hr to 3 hr caused the removal efficiencies of these columns to increase from 22%, 56%, and 54% to 42%, 86%, and 82%, respectively. Also, increasing pH level led to increased removal efficiencies of the studied columns. It was found that contact time played a more effective role in enhancing mercury removal efficiency in the granular activated carbon column than in the other two columns. The ranges of mercury removal efficiency obtained for the granular activated carbon, natural zeolite, and anthracite columns under various conditions were (51%-92%, (42%-88%, and (16%-52%, respectively. Based on these results, granular activated carbon could be recommended as an effective and cheap adsorbent for the removal of mercury from drinking water resources.

  19. Diagenesis and sedimentology of the Clearwater Formation at Tucker Lake

    Energy Technology Data Exchange (ETDEWEB)

    Hutcheon, I; Abercrombie, H J; Putnam, P; Gardner, R; Krouse, H R

    1989-03-01

    The Clearwater Formation at Tucker Lake Alberta, contains heavy oil and is the site of a steam simulation pilot. The best developed reservoir intervals are north-south oriented distributary channel fill and rivermouth bar sand-stones. Oil bearing sands are underlain by a water zone and calcite cements are more abundant in the transition zone. Mineralogy and petrography were studied by x-ray diffraction analysis and scanning electron microscopy, and carbon and oxygen isotope ratios were measured for calcite in the samples studied. The diagenetic history is complex. Early diagenetic minerals include pyrite, quarts, K-feldspar and albite overgrowths, isopachous calcite, iron-rich chlorite, siderite and smectite. Further burial and modification of fluid composition resulted in dissolution of framework mineral grains and precipitation of clinoptilolite and opal. The emplacement of oil retarded mineral diageneses, and was accompanied by a change in aqeous fluid composition. Kaolinite was deposited during and after oil deposition as relativley fresh water entered the Clearwater Formation. The degradation and fermentation of oil and introduction of meteoric water resulted in the production of a late, isotopically distinct, post-bitumen calite cement. 29 refs., 12 figs.

  20. Impacts of zeolite nanoparticles on substrate properties of thin film nanocomposite membranes for engineered osmosis

    Science.gov (United States)

    Salehi, Tahereh Mombeini; Peyravi, Majid; Jahanshahi, Mohsen; Lau, Woei-Jye; Rad, Ali Shokuhi

    2018-04-01

    In this work, microporous substrates modified by zeolite nanoparticles were prepared and used for composite membrane making with the aim of reducing internal concentration polarization (ICP) effect of membranes during engineered osmosis applications. Nanocomposite substrates were fabricated via phase inversion technique by embedding nanostructured zeolite (clinoptilolite) in the range of 0-0.6 wt% into matrix of polyethersulfone (PES) substrate. Of all the substrates prepared, the PES0.4 substrate (with 0.4 wt% zeolite) exhibited unique characteristics, i.e., increased surface porosity, lower structural parameter ( S) (from 0.78 to 0.48 mm), and enhanced water flux. The thin film nanocomposite (TFN) membrane made of this optimized substrate was also reported to exhibit higher water flux compared to the control composite membrane during forward osmosis (FO) and pressure-retarded osmosis (PRO) test, without compromising reverse solute flux. The water flux of such TFN membrane was 43% higher than the control TFC membrane (1.93 L/m2 h bar) with salt rejection recorded at 94.7%. An increment in water flux is ascribed to the reduction in structural parameter, leading to reduced ICP effect.

  1. Radiotracer study of the adsorption of Fe(III), Cr(III) and Cd(II) on natural and chemically modified Slovak zeolite

    International Nuclear Information System (INIS)

    Foeldesova, M.; Dillinger, P.; Lukac, P.

    1998-01-01

    In order to minimize the contamination of environment with metals in ionic form the more types of natural and chemically modified zeolites were examined to their uptake of Fe(III), Cr(III) and Cd(II) from water solutions by batch radio-exchange equilibration method. In this study was used zeolitic tuff from deposit Nizny Hrabovec (content of clinoptilolite 50-70%) with the grain size from 1.2 to 2.2 mm. The granules of zeolite were modified with the following NaOH solutions: ).5, 1, 2 and 4 mol.l -1 at 80 grad C for 4 hours. The sorption of Fe, Cr and Cd ions on all types of zeolites was studied by radio-exchange method and the sorption of Fe and Cr also flame atomic absorption method. From sorption curves the sorption coefficients were calculated. The results obtained in this work show that zeolites modified with NaOH solution are suitable for adsorption of Fe(III), Cr(III) and Cd(II) from underwater, waste water, feed water and coolant water from nuclear plants. The adsorbed zeolites can be solidified by conventional way

  2. Development program for magnetically assisted chemical separation: Evaluation of cesium removal from Hanford tank supernatant

    International Nuclear Information System (INIS)

    Nunez, L.; Buchholz, B.A.; Ziemer, M.; Dyrkacz, G.; Kaminski, M.; Vandegrift, G.F.; Atkins, K.J.; Bos, F.M.; Elder, G.R.; Swift, C.A.

    1994-12-01

    Magnetic particles (MAG*SEP SM ) coated with various absorbents were evaluated for the separation and recovery of low concentrations of cesium from nuclear waste solutions. The MAG*SEP SM particles were coated with (1) clinoptilolite, (2) transylvanian volcanic tuff, (3) resorcinol formaldehyde, and (4) crystalline silico-titanate, and then were contacted with a Hanford supernatant simulant. Particles coated with the crystalline silico-titanate were identified by Bradtec as having the highest capacity for cesium removal under the conditions tested (variation of pH, ionic strength, cesium concentration, and absorbent/solution ratio). The MAG*SEP SM particles coated with resorcinol formaldehyde had high distribution ratios values and could also be used to remove cesium from Hanford supernant simulant. Gamma irradiation studies were performed on the MAG*SEP SM particles with a gamma dose equivalent to 100 cycles of use. This irradiation decreased the loading capacity and distribution ratios for the particles by greater than 75%. The particles demonstrated high sensitivity to radiolytic damage due to the degradation of the polymeric regions. These results were supported by optical microscopy measurements. Overall, use of magnetic particles for cesium separation under nuclear waste conditions was found to be marginally effective

  3. Effect of the humic acids in the adsorption of U (Vi) in a Mexican natural zeolite; Efecto de los acidos humicos en la adsorcion de U (VI) en una zeolita natural mexicana

    Energy Technology Data Exchange (ETDEWEB)

    Sandoval G, H. A.; Lopez del R, H.; Davila R, J. I.; Mireles G, F., E-mail: hlopezdelrio@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

    2012-10-15

    The uranium adsorption was studied in a Mexican natural zeolite of the clinoptilolite type in presence and absence of humic acids (Ha). The adsorption kinetics of the binary U-zeolite and ternary U-Ha-zeolite systems were compared, and the effect of the humic matter impregnated in the zeolite in the uranium removal in function of the solution ph was studied. The experiments were made to environmental conditions and lightly acid ph, with fixed concentrations of uranium and Ha of 1 x 10{sup -5} M and 20 ppm, respectively, and a reason m/V of 5 mg/ml. The uranium adsorption in absence of Ha was of 96% and decreased to 45% in the ternary system U-Ha-zeolite. The data of the binary system U-zeolite were analyzed with three kinetic models of adsorption (pseudo-first order, pseudo-second order and Elovich). By means of non lineal regression was found that the uranium adsorption obeys a kinetic of pseudo-second order. It was observed that the uranium adsorption in the zeolite impregnated with Ha is favored to more ph at 5. (Author)

  4. Quantitative determination of minerals in Nevada Test Site samples by x-ray diffraction

    International Nuclear Information System (INIS)

    Pawloski, G.A.

    1983-07-01

    The external standard intensity ratio technique has been developed into a routine procedure for quantitatively determining mineralogic compositions of Nevada Test Site (NTS) samples by x-ray diffraction. This technique used ratios of x-ray intensity peaks from the same run which eliminates many possible errors. Constants have been determined for each of thirteen minerals commonly found in NTS samples - quartz, montmorillonite, illite, clinoptilolite, cristobalite, feldspars, calcite, dolomite, hornblende, kaolinite, muscovite, biotite, and amorphous glass. Ratios of the highest intensity peak of each mineral to be quantified in the sample and the highest intensity peak of quartz are used to calculate sample composition. The technique has been tested on samples with three to eleven components representative of geologic environments at NTS, and is accurate to 7.0 wt % of the total sample. The minimum amount of each of these minerals detectable by x-ray diffraction has also been determined. QUANTS is a computer code that calculates mineral contents and produces a report sheet. Constants for minerals in NTS samples other than those listed above can easily be determined, and added to QUANTS at any time

  5. Hydrogen Separation by Natural Zeolite Composite Membranes: Single and Multicomponent Gas Transport.

    Science.gov (United States)

    Farjoo, Afrooz; Kuznicki, Steve M; Sadrzadeh, Mohtada

    2017-10-06

    Single and multicomponent gas permeation tests were used to evaluate the performance of metal-supported clinoptilolite membranes. The efficiency of hydrogen separation from lower hydrocarbons (methane, ethane, and ethylene) was studied within the temperature and pressure ranges of 25-600 °C and 110-160 kPa, respectively. The hydrogen separation factor was found to reduce noticeably in the gas mixture compared with single gas experiments at 25 °C. The difference between the single and multicomponent gas results decreased as the temperature increased to higher than 300 °C, which is when the competitive adsorption-diffusion mechanism was replaced by Knudsen diffusion or activated diffusion mechanisms. To evaluate the effect of gas adsorption, the zeolite surface isotherms of each gas in the mixture were obtained from 25 °C to 600 °C. The results indicated negligible adsorption of individual gases at temperatures higher than 300 °C. Increasing the feed pressure resulted in a higher separation efficiency for the individual gases compared with the multicomponent mixture, due to the governing effect of the adsorptive mechanism. This study provides valuable insight into the application of natural zeolites for the separation of hydrogen from a mixture of hydrocarbons.

  6. Employing volcanic tuff minerals in interior architecture design to reduce microbial contaminants and airborne fungal carcinogens of indoor environments.

    Science.gov (United States)

    Gedikoglu, Yaman; Gedikoglu, Gunduz; Berkin, Genco; Ceyhan, Taskin; Altinoz, Meric A

    2012-09-01

    Indoor volatile organic compounds (VOCs) have posed significant risks to human health since people have both shifted to a life spent, for the most part, indoors. Further, changes in materials used in the construction of buildings, furnishings, and tools either leak or encourage the production of VOCs. Whether these enclosed areas are residences, hospitals or workplaces (specifically composting facilities or closed farm buildings for raising livestock), VOCs can rise to levels that threaten people's health. VOCs can either originate from phenolic and benzene-like compounds in building materials and office furniture or from molds (fungi) growing inside improperly ventilated or sealed buildings. Regardless of the source, exposure to VOCs could lead to significant health concerns from sick-building syndrome, 'leukemia houses,' in-hospital fungemia cases or occupation-associated cancer epidemics due to aflatoxicosis. Innovative 21st-century building materials could offer solutions to these challenges. We propose that volcanic materials, clays and minerals (volcanic tuff, modified clay montmorillonite and mineral clinoptilolite), in their original or chemically modified form, could act like synthetic lungs in building walls, breathing and filtering VOCs, and thus limiting human exposure to disease.

  7. Modification of alternative additives and their effect on the rubber properties

    Directory of Open Access Journals (Sweden)

    Ondrušová Darina

    2018-01-01

    Full Text Available The present paper deals with a targeted modification of two kinds of alternative additives - waste from glass production and natural mineral filler and explores their effect on the properties of polymeric materials. In the function of first alternative filler was used sludge from weighing the ingredients of glass batch in the glass production. The second used was natural aluminosilicate material based on zeolite (clinoptilolite. These alternative fillers have been modified in order to increase its efficiency, using the silanes: 3-aminopropyl-triethoxysilane, bis(triethoxysilylpropyl-tetrasulfide and 3-(triethoxysilylpropyl-methacrylate. In the case of alternative filler based on zeolite the influence of silanization conditions on the filler efficiency have been also studied. Prepared modified fillers were mixed into rubber compounds as partial replacement of commonly used filler – carbon black. The influence of prepared fillers on rheology and curing characteristics of rubber compounds and also on physical and mechanical properties of vulcanizates has been studied. Obtained results of measured characteristics of polymeric systems containing prepared alternative fillers were compared with the results obtained in the case of reference rubber compound with a commertially used filler – carbon black.

  8. Possibilities of utilizing zeolites for the reduction of toxical noxious gases of combustion engines

    Directory of Open Access Journals (Sweden)

    Pandová Iveta

    2001-12-01

    Full Text Available Combustion engines produce exhalations that contribute by 50% to the contamination of the environment. The subject of this work is the research of zeolites´ as the adsorbent of toxical gases. The decisive influence on the adsorbing power has the capacity of porous in unit of volume of the sorbent and dimensions of canals. The active component of zeolite from the deposit Bystré is mineral clinoptilolite. Recently, there is an increased interest to utilize zeolites in the partial reduction of NOx, CO and hydrocarbons in the combustion products. The catalysts used to detoxication of exhalation combustion engines are less effective during periods of relatively low temperature operation, such as the initial cold-start period of engine operation. Some European, American and Japones patents are directed to the use of a zeolite catalyst for the reduction of hydrocarbons, CO and NOx. The noble metals and acid zeolites are used as a catalyst of noxious components. The adsorbent material, which may be a zeolite is part treatment system in order to adsorb gaseous pollutants during of cold start period of engine operation.

  9. Use of inorganic sorbents for treatment of liquid radioactive waste and backfill of underground repositories

    International Nuclear Information System (INIS)

    1992-11-01

    This document presents the results of a four year Co-ordinated Research Programme (CRP) on the ''Use of Inorganic Sorbents for Treatment of Liquid Radioactive Waste and Backfill of Underground Repositories'' (1987-1991). Many countries have research programmes aiming at developing processes which would provide efficient and safe concentration of radionuclides in waste streams into solid materials which could then be reliably immobilized into forms suitable for long term storage or disposal. Use of inorganic sorbents for this purpose is very attractive because of their resistance to radiation and chemical attack, strong affinity for one or more radionuclides, their compatibility with likely immobilization matrices and their availability at low cost. According to the fundamental multibarrier concept for disposal of radioactive waste, backfill material is one of the important engineered barriers. Inorganic materials such as clays, naturally occurring zeolites (clinoptilolite, modenite and chabasite) are promising backfill materials. Research in technical uses of inorganic material applications was covered within the framework of the Co-ordinated Research Programme reported in this technical document. Final contributions by participants at the last Research Co-ordination Meeting held in Rez, Czechoslovakia, from 4 to 8 November 1991, are presented here. Refs, figs and tabs

  10. Textural Properties of Hybrid Biomedical Materials Made from Extracts of Tournefortia hirsutissima L. Imbibed and Deposited on Mesoporous and Microporous Materials

    Directory of Open Access Journals (Sweden)

    Miguel Ángel Hernández

    2016-01-01

    Full Text Available Our research group has developed a group of hybrid biomedical materials potentially useful in the healing of diabetic foot ulcerations. The organic part of this type of hybrid materials consists of nanometric deposits, proceeding from the Mexican medicinal plant Tournefortia hirsutissima L., while the inorganic part is composed of a zeolite mixture that includes LTA, ZSM-5, clinoptilolite, and montmorillonite (PZX as well as a composite material, made of CaCO3 and montmorillonite (NABE. The organic part has been analyzed by GC-MS to detect the most abundant components present therein. In turn, the inorganic supports were characterized by XRD, SEM, and High Resolution Adsorption (HRADS of N2 at 76 K. Through this latter methodology, the external surface area of the hybrid materials was evaluated; besides, the most representative textural properties of each substrate such as total pore volume, pore size distribution, and, in some cases, the volume of micropores were calculated. The formation and stabilization of nanodeposits on the inorganic segments of the hybrid supports led to a partial blockage of the microporosity of the LTA and ZSM5 zeolites; this same effect occurred with the NABE and PZX substrates.

  11. Lead (II) removal from natural soils by enhanced electrokinetic remediation.

    Science.gov (United States)

    Altin, Ahmet; Degirmenci, Mustafa

    2005-01-20

    Electrokinetic remediation is a very effective method to remove metal from fine-grained soils having low adsorption and buffering capacity. However, remediation of soil having high alkali and adsorption capacity via the electrokinetic method is a very difficult process. Therefore, enhancement techniques are required for use in these soil types. In this study, the effect of the presence of minerals having high alkali and cation exchange capacity in natural soil polluted with lead (II) was investigated by means of the efficiency of electrokinetic remediation method. Natural soil samples containing clinoptilolite, gypsum and calcite minerals were used in experimental studies. Moreover, a sample containing kaolinite minerals was studied to compare with the results obtained from other samples. Best results for soils bearing alkali and high sorption capacity minerals were obtained upon addition of 3 mol AcH and application of 20 V constant potential after a remediation period of 220 h. In these test conditions, lead (II) removal efficiencies for these samples varied between 60% and 70% up to 0.55 normalized distance. Under the same conditions, removal efficiencies in kaolinite sample varied between 50% and 95% up to 0.9 normalized distance.

  12. Plant of treatment of porcine waters with the use of the biogestion anaerobic and filtration with zeolite type clinoptilolite

    International Nuclear Information System (INIS)

    Nikolaeva, S.; Rua, F.; Mederos, B.

    2002-01-01

    Due to the worry by the contamination of the environment, the processing of the residuals waters should be focused from the ecological point of view and of the improvement of the human health. Today we know technologies that treat and purify practically any type of residual water; for this are taken into account aspects like: subsequent disposition, take advantage of the natural local conditions, cost of the construction of the installations, costs and facilities of operation and maintenance. To present an option of the pork residual water processing, a joint project between the Universidad Nacional and the Colegio Agropecuario de Santa Clara was presented, with the financial support of the German Agency of Technical Cooperation (GTZ) [es

  13. Effect of the modification of a natural mexican zeolite in the sorption of cadmium and 4-chloro phenol; Efecto de la modificacion de una zeolita natural mexicana en la sorcion de cadmio y 4-clorofenol

    Energy Technology Data Exchange (ETDEWEB)

    Cortes M, R [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

    2007-07-01

    Clinoptilolite type zeolite is a material of relative abundance in Mexico, which possess ion exchange properties and it can be used in the removal of metal ions from polluted waters. The external surface of zeolites can be modified with cationic surfactants. This modification could have a negative effect on the removal of metal ions and provides to the material the capacity to adsorb phenolic compounds. For this reason, it is important to know the capability of the modified material on the sorption of metal ions and phenolic compounds, simultaneously. The aim of this work was to evaluate the effect of the external surface modification with surfactant of a Mexican zeolite over its sorption capacity of cadmium and 4-chloro phenol, in batch and column systems. To accomplish that, a clinoptilolite type zeolitic rock from a deposit located in the state of Sonora, Mexico, was used. It was ground, sieved and characterized with different techniques; and its external surface area was modified with hexadecyltrimethylammonium bromide (HDTMA-Br). A grain size fraction was selected to carry out sorption kinetics and equilibrium experiments, as well as packed column tests with zeolitic material and solutions of cadmium and 4-chloro phenol. There are different models proposed in literature that are used to describe sorption kinetics and equilibrium. In this work, the sorption experimental results were adjusted to some of these models to identify controlling mechanisms on the kinetics and equilibrium of the studied systems. The results showed that the cadmium adsorption on natural and modified zeolite was similar in batch systems. For the case of 4-chloro phenol sorption, it was observed that natural zeolite does not retain this compound, while in modified zeolite the sorption is better than other comparable materials. The results also showed that for the case of cadmium sorption, the mechanism involved was ion exchange; while for sorption of 4-chloro phenol, a partition mechanism

  14. Effect of the modification of a natural mexican zeolite in the sorption of cadmium and 4-chloro phenol

    International Nuclear Information System (INIS)

    Cortes M, R.

    2007-01-01

    Clinoptilolite type zeolite is a material of relative abundance in Mexico, which possess ion exchange properties and it can be used in the removal of metal ions from polluted waters. The external surface of zeolites can be modified with cationic surfactants. This modification could have a negative effect on the removal of metal ions and provides to the material the capacity to adsorb phenolic compounds. For this reason, it is important to know the capability of the modified material on the sorption of metal ions and phenolic compounds, simultaneously. The aim of this work was to evaluate the effect of the external surface modification with surfactant of a Mexican zeolite over its sorption capacity of cadmium and 4-chloro phenol, in batch and column systems. To accomplish that, a clinoptilolite type zeolitic rock from a deposit located in the state of Sonora, Mexico, was used. It was ground, sieved and characterized with different techniques; and its external surface area was modified with hexadecyltrimethylammonium bromide (HDTMA-Br). A grain size fraction was selected to carry out sorption kinetics and equilibrium experiments, as well as packed column tests with zeolitic material and solutions of cadmium and 4-chloro phenol. There are different models proposed in literature that are used to describe sorption kinetics and equilibrium. In this work, the sorption experimental results were adjusted to some of these models to identify controlling mechanisms on the kinetics and equilibrium of the studied systems. The results showed that the cadmium adsorption on natural and modified zeolite was similar in batch systems. For the case of 4-chloro phenol sorption, it was observed that natural zeolite does not retain this compound, while in modified zeolite the sorption is better than other comparable materials. The results also showed that for the case of cadmium sorption, the mechanism involved was ion exchange; while for sorption of 4-chloro phenol, a partition mechanism

  15. Production of sorption functional media (SFM) from clinoptilolite tailings and its performance investigation in a biological aerated filter (BAF) reactor

    International Nuclear Information System (INIS)

    Feng, Yan; Qi, Jingyao; Chi, Liying; Wang, Dong; Wang, Zhaoyang; Li, Ke; Li, Xin

    2013-01-01

    Highlights: ► Sorption functional media (SFM) were prepared using zeolite tailings. ► Two upflow BAFs were applied to treat municipal wastewater. ► SFM BAF brought a relative superiority to haydite reactor. ► SFM BAF has a stronger adaptability to low temperature (6–11°C) for NH 3 -N removal. ► The application provided a promising way in zeolite tailings utilization. -- Abstract: The few reuse and large stockpile of zeolite tailings led to a series of social and environmental problems. This study investigated the possibility of using the zeolite tailings as one of principal raw materials to prepare sorption functional media (SFM) by a high temperature sintering process. The SFM was used to serve as a biomedium in a biological aerated filter (BAF) reactor for domestic wastewater treatment, and its purification performance was examined. The physical, chemical and sorption properties of SFM were also determined. The microstructure of the SFM was analyzed by scanning electron microscopy (SEM). Results revealed that: (1) zeolite tailings could be used to produce the SFM under the optimal sintering parameters; (2) the sorption and desorption isotherm of ammonia nitrogen on SFM could be well described by the Langmuir formula; (3) in terms of removing organic matter, ammonia nitrogen, turbidity and colourity, the performance of the biofilter with SFM was superior to that with haydite; and (4) SFM BAF has a stronger adaptability to low temperature (6–11 °C) for NH 3 -N removal compared to haydite BAF. Therefore, the SFM produced from the zeolite tailings was suitable to serve as the biomedium in the domestic wastewater treatment

  16. Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: the influence of zeolite chemical surface characteristics.

    Science.gov (United States)

    Alejandro, Serguei; Valdés, Héctor; Manéro, Marie-Hélène; Zaror, Claudio A

    2014-06-15

    In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Effect of diverse ions, column temperature and flow rate on the dynamic exchange-properties of cesium in various types of zeolites

    International Nuclear Information System (INIS)

    Mimura, Hitoshi; Kanno, Takuji; Kimura, Toshiya.

    1982-01-01

    The effect of various diverse ions in solution, column temperature and flow rate on the dynamic exchange-properties of Cs have been studied with various types of zeolites, i.e., synthetic mordenite, natural mordenite and clinoptilolite. The concentration of nitric acid considerably affects on the break-through properties of Cs; break-through capacity (B. T. Cap), total capacity (T. Cap) and column utilization (U) decrease with increasing acid concentration. The break-throgh data in the pH range (pH >= 1) are as follows; above 50 (meq./100 g zeolite) for B. T. Cap, 110 (meq./100 g zeolite) for T. Cap and 45 (%) for U, respectively. On the other hand, the concentration of formic acid (<= 2 M) and sodium ion (<= 0.1 M) give no critical change on the break-through properties, and T. Cap was found to be nearly constant. Break-through capacity and exchange rate increase with an increase in column temperature, while T. Cap remains constant. Thus, a similar profile was found in the curves of these properties as a function of temperature. Their inflection point gives the value of C/Co asymptotically equals 0.63. The decrease in flow rate (S. V) appears to give an increase in both B. T. Cap and U. (author)

  18. Obtaining of iron particles of nanometer size in a natural zeolite; Obtencion de particulas de hierro de tamano nanometrico en una zeolita natural

    Energy Technology Data Exchange (ETDEWEB)

    Xingu C, E. G.

    2013-07-01

    The zeolites are aluminosilicates with cavities that can act as molecular sieve. Their crystalline structure is formed by tetrahedrons that get together giving place to a three-dimensional net, in which each oxygen is shared by two silicon atoms, being this way part of the tecto silicate minerals, its external and internal areas reach the hundred square meters for gram, they are located in a natural way in a large part of earth crust and also exist in a synthetic way. In Mexico there are different locations of zeolitic material whose important component is the clinoptilolite. In this work the results of three zeolitic materials coming from San Luis Potosi are shown, the samples were milled and sieved for its initial characterization, to know its chemical composition, crystalline phases, morphology, topology and thermal behavior before and after its homo-ionization with sodium chloride, its use as support of iron particles of nanometer size. The description of the synthesis of iron particles of nanometer size is also presented, as well as the comparison with the particles of nanometer size synthesized without support after its characterization. The characterization techniques used during the experimental work were: Scanning electron microscopy, X-ray diffraction, Infrared spectroscopy, specific area by means of BET and thermogravimetry analysis. (Author)

  19. Natural zeolites in diet or litter of broilers.

    Science.gov (United States)

    Schneider, A F; Almeida, D S De; Yuri, F M; Zimmermann, O F; Gerber, M W; Gewehr, C E

    2016-04-01

    This study aims to analyse the influence of adding natural zeolites (clinoptilolite) to the diet or litter of broilers and their effects on growth performance, carcass yield and litter quality. Three consecutive flocks of broilers were raised on the same sawdust litter, from d 1 to d 42 of age, and distributed in three treatments (control with no added zeolites, addition of 5 g/kg zeolite to diet and addition of 100 g/kg zeolites to litter). The addition of zeolites to the diet or litter did not affect growth performance or carcass yield. The addition of zeolites to the diet did not influence moisture content of the litter, ammonia volatilisation was reduced only in the first flock and pH of litter was reduced in the second and third flock. However, the addition of zeolites to the litter reduced moisture content, litter pH and ammonia volatilisation in all flocks analysed. The addition of 5 g/kg zeolite to the diet in three consecutive flocks was not effective in maintaining litter quality, whereas the addition of 100 g/kg natural zeolites to sawdust litter reduced litter moisture and ammonia volatilisation in three consecutive flocks raised on the same litter.

  20. Smectite-zeolite envelope surrounding the Tsukiyoshi uranium deposit, central Japan. A natural analogue study

    International Nuclear Information System (INIS)

    Utada, Minoru

    2003-01-01

    The Tsukiyoshi uranium deposit in Gifu Prefecture is the largest one in Japan. It is embedded in lower part of the Mizunami Group of Miocene age. Relating to the existence of this uranium deposit, the constituent minerals in sediments were studied by XRD and SEM, using many drilling cores. The most abundant authigenic mineral is smectite. The amount of smectite increases generally from upper to lower horizons, and a highly smectitized zone is situated around the uranium deposit. Smectitization predominated in mafic glassy grains of sediments, which was probably formed in early burial diagenesis. Zeolites including clinoptilolite-heulandite, mordenite, analcime, chabazite and philipsite are secondly abundant authigenic minerals. They seem to have been formed at early to late diagenetic stages. Opaline silica is rather rare. Carbonate minerals, including calcite, dolomite, siderite and rhodocrosite are common. They may be formed by diagenesis as well. Gypsum and pyrite occur in upper horizons and lower horizons, respectively. In particular, a highly smectitized zone including pyrite probably played an important role for retarding the migration of uranium and as a result keeping the uranium deposit for past one million years. This smectite-zeolite envelope surrounding the Tsukiyoshi uranium deposit is regarded as a natural analogue of the buffer materials surrounding the high-level radioactive waste repository. (author)

  1. Obtaining of iron particles of nanometer size in a natural zeolite

    International Nuclear Information System (INIS)

    Xingu C, E. G.

    2013-01-01

    The zeolites are aluminosilicates with cavities that can act as molecular sieve. Their crystalline structure is formed by tetrahedrons that get together giving place to a three-dimensional net, in which each oxygen is shared by two silicon atoms, being this way part of the tecto silicate minerals, its external and internal areas reach the hundred square meters for gram, they are located in a natural way in a large part of earth crust and also exist in a synthetic way. In Mexico there are different locations of zeolitic material whose important component is the clinoptilolite. In this work the results of three zeolitic materials coming from San Luis Potosi are shown, the samples were milled and sieved for its initial characterization, to know its chemical composition, crystalline phases, morphology, topology and thermal behavior before and after its homo-ionization with sodium chloride, its use as support of iron particles of nanometer size. The description of the synthesis of iron particles of nanometer size is also presented, as well as the comparison with the particles of nanometer size synthesized without support after its characterization. The characterization techniques used during the experimental work were: Scanning electron microscopy, X-ray diffraction, Infrared spectroscopy, specific area by means of BET and thermogravimetry analysis. (Author)

  2. Hydrogen Separation by Natural Zeolite Composite Membranes: Single and Multicomponent Gas Transport

    Directory of Open Access Journals (Sweden)

    Afrooz Farjoo

    2017-10-01

    Full Text Available Single and multicomponent gas permeation tests were used to evaluate the performance of metal-supported clinoptilolite membranes. The efficiency of hydrogen separation from lower hydrocarbons (methane, ethane, and ethylene was studied within the temperature and pressure ranges of 25–600 °C and 110–160 kPa, respectively. The hydrogen separation factor was found to reduce noticeably in the gas mixture compared with single gas experiments at 25 °C. The difference between the single and multicomponent gas results decreased as the temperature increased to higher than 300 °C, which is when the competitive adsorption–diffusion mechanism was replaced by Knudsen diffusion or activated diffusion mechanisms. To evaluate the effect of gas adsorption, the zeolite surface isotherms of each gas in the mixture were obtained from 25 °C to 600 °C. The results indicated negligible adsorption of individual gases at temperatures higher than 300 °C. Increasing the feed pressure resulted in a higher separation efficiency for the individual gases compared with the multicomponent mixture, due to the governing effect of the adsorptive mechanism. This study provides valuable insight into the application of natural zeolites for the separation of hydrogen from a mixture of hydrocarbons.

  3. Removal of pyridine from liquid and gas phase by copper forms of natural and synthetic zeolites

    International Nuclear Information System (INIS)

    Rehakova, Maria; Fortunova, Lubica; Bastl, Zdenek; Nagyova, Stanislava; Dolinska, Silvia; Jorik, Vladimir; Jona, Eugen

    2011-01-01

    Zeoadsorbents on the basis of copper forms of synthetic zeolite ZSM5 and natural zeolite of the clinoptilolite type (CT) have been studied taking into account their environmental application in removing harmful pyridine (py) from liquid and gas phase. Sorption of pyridine by copper forms of zeolites (Cu-ZSM5 and Cu-CT) has been studied by CHN, X-ray photoelectron spectroscopy, X-ray powder diffractometry, FTIR spectroscopy, thermal analysis (TG, DTA and DTG) and analysis of the surface areas and the pore volumes by low-temperature adsorption of nitrogen. The results of thermal analyses of Cu-ZSM5, Cu-(py) x ZSM5, Cu-CT and Cu-(py) x CT zeolitic products with different composition (x depends on the experimental conditions of sorption of pyridine) clearly confirmed their different thermal properties as well as the sorption of pyridine. In the zeolitic pyridine containing samples the main part of the pyridine release process occurs at considerably higher temperatures than is the boiling point of pyridine, which proves strong bond and irreversibility of py-zeolite interaction. FTIR spectra of Cu-(py) x zeolite samples showed well resolved bands of pyridine. The results of thermal analysis and FTIR spectroscopy are in a good agreement with the results of other used methods.

  4. Competitive adsorption of dyes and heavy metals on zeolitic structures.

    Science.gov (United States)

    Hernández-Montoya, V; Pérez-Cruz, M A; Mendoza-Castillo, D I; Moreno-Virgen, M R; Bonilla-Petriciolet, A

    2013-02-15

    The adsorption of Acid blue 25, basic blue 9, basic violet 3, Pb(2+), Ni(2+), Zn(2+) and Cd(2+) ions has been studied in single and dye-metal binary solutions using two mineral materials: Clinoptilolite (CL) and ER (Erionite). These zeolites were characterized by FT-IR spectroscopy; potentiometric titration and nitrogen adsorption isotherms at 77 K to obtain their textural parameters. Results indicated that ER has an acidic character and a high specific surface (401 m(2) g(-1)) in contrast with the zeolite CL (21 m(2) g(-1)). Surprisingly, the removal of dyes was very similar for the two zeolites and they showed a considerable selectivity by the basic dyes in comparison with the acid dyes. In the case of heavy metals, ER was more effective in the adsorption process showing a selectivity of: Pb(2+) > Ni(2+) > Zn(2+) > Cd(2+). In the multicomponent adsorption experiments an antagonistic effect was observed in the removal of basic dyes and heavy metals. Particularly, the adsorbed amount of basic violet 3 decreased more significantly when the heavy metals are presents in contrast with the basic blue 9. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Processing of radioactive waste solution with zeolites, (4)

    International Nuclear Information System (INIS)

    Mimura, Hitoshi; Kanno, Takuji

    1978-01-01

    Volatilization of Cs from Cs type zeolites and calcined zeolites were studied at high temperature. Synthetic zeolites A, X, Y, synthetic mordenite (Zeolon), natural mordenite and clinoptilolite saturated with Cs were used in this study. Volatilized Cs from CsX was largest in quantity and from cs type natural zeolites smallest. Volatilization of Cs was observed at about 800 0 C and increased as the calcining temperature rose. Volatilized Cs from CsA was smallest in synthetic zeolites. CsA recrystallized to nepheline and pollucite with the ratio of about 1 : 1 above 1,000 0 C and it seemed that the volatilization of Cs from pollucite was suppressed with the nepheline phase surrounded them. The rate of volatilization was very fast within the initial 10 min and very slow after 60 min except for CsX. This behavior suggested that the rate was very fast before structural transformation. The mean volatilization rate of Cs in 3 hr from calcined CsX (pollucite) was 1.1 x 10 -4 mg/cm 2 .min and the others were 10 -5 -- 10 -6 mg/cm 2 .min. The amount of volatilized Cs in Ar flow was decreased 20 -- 90% of that in air flow. Volatilized species was identified with Cs 2 O by mass spectrometry. (auth.)

  6. Kinetic Modelling of the Removal of Multiple Heavy Metallic Ions from Mine Waste by Natural Zeolite Sorption

    Directory of Open Access Journals (Sweden)

    Amanda L. Ciosek

    2017-07-01

    Full Text Available This study investigates the sorption of heavy metallic ions (HMIs, specifically lead (Pb2+, copper (Cu2+, iron (Fe3+, nickel (Ni2+ and zinc (Zn2+, by natural zeolite (clinoptilolite. These HMIs are combined in single-, dual-, triple-, and multi-component systems. The batch mode experiments consist of a total initial concentration of 10 meq/L normality for all systems, acidified to a pH of 2 by concentrated nitric (HNO3 acid. A zeolite dosage of 4 g per 100 mL of synthetic nitrate salt aqueous solution is applied, for a contact period of 5 to 180 min. Existing kinetic models on HMIs sorption are limited for multi-component system combinations. Therefore, this study conducts kinetic analysis by both reaction and diffusion models, to quantify the sorption process. The study concludes that the process correlates best with the pseudo-second-order (PSO kinetic model. In the multi-component system combining all five HMIs, the initial sorption rate and theoretical equilibrium capacity are determined as 0.0033 meq/g·min and 0.1159 meq/g, respectively. This provides significant insight into the mechanisms associated with the sorption process, as well as contributing to the assessment of natural zeolite as a sorbent material in its application in industrial wastewater treatment.

  7. Evaluation of engineering aspects of backfill placement for high level nuclear waste (HLW) deep geologic repositories

    International Nuclear Information System (INIS)

    Roberds, W.; Kleppe, J.; Gonano, L.

    1984-04-01

    This report includes the identification and subjective evaluation of alternative schemes for backfilling around waste packages and within emplacement rooms. The aspects of backfilling specifically considered in this study include construction and testing; costs have not been considered. However, because construction and testing are simply implementation and verification of design, a design basis for backfill is required. A generic basis has been developed for this study by first identifying qualitative performance objectives for backfill and then weighting each with respect to its potential influence on achieving the repository system performance objectives. Alternative backfill materials and additives have been identified and evaluated with respect to the perceived extent to which each combination can be expected to achieve the backfill design basis. Several distinctly different combinations of materials and additives which are perceived to have the highest potential for achieving the backfill design basis have been selected for further study. These combinations include zeolite/clinoptilolite, bentonite, muck, and muck mixed with bentonite. Feasible alternative construction and testing procedures for each selected combination have been discussed. Recommendations have been made regarding appropriate backfill schemes for hard rock (i.e., basalt at Hanford, Washington, tuff at Nevada Test Site, and generic granite) and salt (i.e., domal salt on the Gulf Coast and generic bedded salt). 27 references, 8 figures, 31 tables

  8. Application of Response Surface Methodology to Optimize Malachite Green Removal by Cl-nZVI Nanocomposites

    Directory of Open Access Journals (Sweden)

    Farshid Ghorbani

    2017-09-01

    Full Text Available Disposal of effluents containing dyes into natural ecosystems pose serious threats to both the environment and its aquatic life. Malachite green (MG is a basic dye that has extensive industrial applications, especially in aquaculture, throughout the world. This study reports on the application of the central composite design (CCD under the response surface methodology (RSM for the optimization of MG adsorption from aqueous solutions using the clinoptilolite nano-zerovalence iron (Cl-nZVI nanocomposites. The sorbent structures produced are characterized by means of scanning electron micrograph (SEM, energy-dispersive X-ray spectroscopy (EDS, and vibrating sample magnetometer (VSM. The effects of different parameters including pH, initial MG concentration, and sorbent dosage on the removal efficiency (R of MG were studied to find the optimum operating conditions. For this purpose, a total of 20 sets of experiments were designed by the Design Expert.7.0 software and the values of removal efficiency were used as input response to the software. The optimum pH, initial MG concentration, and sorbent dosage were found to be 5.6, 49.21 mg.L-1, and 1.43 g.L-1, respectively. A high MG removal efficiency (57.90% was obtained with optimal process parameters. Moreover, a desirability value of 0.963 was obtained for the optimization process.

  9. Denitration of simulated high-level liquid wastes and selective removal of cesium with zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Mimura, Hitoshi; Kanno, Takuji [Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy; Kimura, Toshiya

    1982-03-01

    Denitration of high-level liquid wastes (HLW) from nuclear fuel reprocessing has been studied. Selective removal of Cs has been also examined with various types of zeolites. The following zeolites were used in this study; Na-synthetic mordenite (NaSM), Na-natural mordenite (NaNM), Na-natural clinoptilolite (NaCP) and H-synthetic mordenites (HSM). The effective denitration is found in the simulated HLW (15 components, 2N HNO/sub 3/ soln.) containing platinum group elements in the case of the addition of formic acid, and the pH of the solution shows the value of 5.4 when the excess formic acid ((HCOOH)/(HNO/sub 3/) = 2.0) was added. Platinum group elements may react as a catalyst for the decomposition of nitric acid and the excess formic acid. The break-through properties of NaSM column are poor for the simulated HLW, and the selective removal of Cs appears to be difficult. On the other hand, good results are obtained in the denitrated HLW, i.e., break-through capacity, total capacity and column utilization are 59.4 (meq./100 g zeolite), 147 (meq./100 g zeolite) and 40.4 (%), respectively. The break-through properties of NaSM and NaNM are superior to those of HSM. The break-through capacity and column utilization increase with an increase in column temperature.

  10. http://fsu.ua/index.php/en/2017/2-2017-40/2017-02-099-113-kononenko

    Directory of Open Access Journals (Sweden)

    O. Baturevich

    2017-06-01

    Full Text Available Purpose.To describe the basic physical-chemical and biological properties of certain minerals of volcanic origin, which are deposited in Ukraine.To examine and make a comparative assessment of their chemical composition and biological properties including zeolite, bentonite and saponite. To summarize performance data on the effectiveness of their use in animal, poultry and fish feed as a feed additive. Findings. Groups of zeolites, saponins and bentonites among the minerals of volcanic origin, which are deposited on Ukrainian territory, have been examined. The chemical composition, and hence the properties of these minerals have significant differences. The scientific review of papers shows their wide application in industry, medicine and animal breeding. Zeolite component is presented by clinoptilolite which is suitable for animal feed because of the structure of the crystal lattice. Its structure and chemical composition is determined by sorbing and ion exchange properties. There is a positive effect of zeolite, bentonite and saponite on animals. Zeolites are used in pisciculture in order to increase fish productivity of fisheries and clean fishing reservoir water. The perspective of research efficiency of volcanic origin minerals in fish feeding before the sawning period was determined Practical value. Analysis and synthesis of scientific studies in various fields of animal breeding will help to determine the prospects and ways of the application of the minerals of volcanic origin (bentonite, zeolite and saponite in pisciculture

  11. Pyrolysis of polyethylene terephthalate containing real waste plastics using Ni loaded zeolite catalysts

    Science.gov (United States)

    Al-asadi, M.; Miskolczi, N.

    2018-05-01

    In this work the pyrolysis of polyethylene terephthalate (PET) containing real waste plastic was investigated using different Ni loaded catalysts: Ni/ZSM-5, Ni/y-zeolite, Ni/β-zeolite and Ni/natural zeolite (clinoptilolite). Raw materials were pyrolyzed in a horizontal tubular reactor between 600 and 900°C using 10% of catalysts. It was found, that both temperature increasing and catalysts presence can increase the gas yields, however owing to gasification reactions, the pyrolysis oil yield decreased with increasing temperature. Ni/y-zeolite catalyst had the most benefit in gas yield increasing at low temperature; however Ni/ZSM-5 showed advanced property in gas yield increasing at high temperature. Gases contained hydrogen, carbon oxides and hydrocarbons, which composition was significantly affected by catalysts. Ni loaded zeolites favoured to the formation of hydrogen and branched hydrocarbons; furthermore the concentrations of both CO and CO2 were also increased as function of elevated temperature. That phenomenon was attributed to the further decomposition of PET, especially to the side chain scission reactions. Owing to the Boudouard reaction, the ratio of CO2/CO can increased with temperature. Pyrolysis oils were the mixtures of n-saturated, n-unsaturated, branched, oxygen free aromatics and oxygenated hydrocarbons. Temperature increasing has a significant effect to the aromatization and isomerization reactions, while the catalysts can efficiently decreased the concentration of oxygen containing compounds.

  12. Transformation of Indonesian Natural Zeolite into Analcime Phase under Hydrothermal Condition

    Science.gov (United States)

    Lestari, W. W.; Hasanah, D. N.; Putra, R.; Mukti, R. R.; Nugrahaningtyas, K. D.

    2018-04-01

    Natural zeolite is abundantly available in Indonesia and well distributed especially in the volcano area like Java, Sumatera, and Sulawesi. So far, natural zeolite from Klaten, Central Java is one of the most interesting zeolites has been widely studied. This research aims to know the effect of seed-assisted synthesis under a hydrothermal condition at 120 °C for 24 hours of Klaten’s zeolite toward the structural change and phase transformation of the original structure. According to XRD and XRF analysis, seed-assisted synthesis through the addition of aluminosilicate mother solution has transformed Klaten’s zeolite which contains (mordenite and clinoptilolite) into analcime type with decreasing Si/Al ratio from 4.51 into 1.38. Morphological analysis using SEM showed the shape changes from irregular into spherical looks like takraw ball in the range of 0.3 to 0.7 micrometer. Based on FTIR data, structure of TO4 site (T = Si or Al) was observed in the range of 300-1300 cm-1 and the occupancy of Brønsted acid site as OH stretching band from silanol groups was detected at 3440-3650 cm-1. Nitrogen adsorption-desorption analysis confirmed that transformation Klaten’s zeolite into analcime type has decreased the surface area from 55.41 to 22.89 m2/g and showed inhomogeneous pore distribution which can be classified as micro-mesoporous aluminosilicate materials.

  13. Effect of special modified clinoptylolite as an antidote used for treatment of radiocaesium contamination of broiler chicken

    International Nuclear Information System (INIS)

    Poschl, M.; Borkovec, V.; Zelenka, J.; Prochazka, J.

    1994-01-01

    The post-Chernobyl 137 Cs contamination caused gut uptake of this nuclide by ruminants, pigs and laying hens. The application of several clay minerals, stable caesium as well as hexacyanoferrate and related compounds has shown to be effective in reducing the gut uptake. The aim of this study was focused on a possibility of the suppression of gut uptake of 13 '7Cs from the contaminated feed mixture to broiler chicken and/or increasing the rate of excretion of 137 Cs from tissues of broiler chicken by a special food additive (RADECONT, i.e. 98% of clinoptilolite + 2% of FeHCF, made by BIOPOR, CZ). The antidote material RADECONT was added to the feed mixture 2 hours after application of artificially contaminated feed (5kBq of 137 Cs per chicken). The dose of the material was 0.5g per kg body weight and it was repeated daily. The control chickens were given 137 Cs but not antidote in the feed. Lower radiocaesium activities in breast and leg muscles (statistically significant, P 137 Cs administration. The biological half-lives of 137 Cs in the controls treated animals were similar. Application of RADECONT decreased the uptake of radiocaesium in tissues (by up to 20% in muscles) but did not enhance the excretion rate of 137 Cs. (author)

  14. Zeolite from Cikancra Tasikmalaya, West Java: a review of its properties

    International Nuclear Information System (INIS)

    Estiaty, Lenny Marilyn; Prijatama, Herry; Zulkarnain, Iskandar; Kurnia, Dewi F.; Nurlela, Iis; Goto, Yoshiaki; Szuciya

    2002-01-01

    Samples from natural zeolite deposit in Cikancra village, Tasikmalaya, West Java were investigated for its main properties. Chemical composition was analyzed by X-ray Fluorescence (XRF) and Atomic Absorption Spectrometry (AAS) methods. Mineralogical analyses were carried out using X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM) methods. Furthermore, continuous flow method was applied for cation exchange capacity (CEC) determination and TG-DTA (thermal gravimetry - differential thermal analysis) was carried out to see the thermal behaviour of the zeolite. Analysis results showed that the chemical composition was dominated by silica and alumina, while other elements like sodium, iron, potassium and titanium were present in lesser amounts. The sellite type was identified as mordenite and depopulation. SEM photographs indicated crystals of mordenite in fibrous or needle forms and platy clinoptilolite. Zeolite Cikancra was also found to have a relatively high exchange capacity with a CEC value of 143.58 meq/100 g. Thermal analysis revealed that water vapor was released from zeolite at temperature of 80.5 to 148 oC with a weight loss of 9.4%. Furthermore, crystal water was released at 481.8 oC , which was indicated with a weight loss of 4.3%. Based on those determined properties, Zeolite Cikancra has the ability to be used for wastewater treatment, agriculture or animal nutrient applications, drying and odorless

  15. Removal of Cr(VI and Toxic Ions from Aqueous Solutions and Tannery Wastewater Using Polymer-Clay Composites

    Directory of Open Access Journals (Sweden)

    Abd El-Azeem Sallam

    2017-10-01

    Full Text Available Polymer-clay composites were prepared by natural zeolite (clinoptilolite or naturally local clay deposits in an N,N-methylene-bis-acrylamide as cross-linked. The resultant composites were used for the removal of Cr(VI from an aqueous solution. Additionally, their effects on soluble ions of tannery wastewater were investigated. The produced composites were characterized using X-ray diffraction (XRD, Fourier transform infrared spectroscopy (FT-IR, and scanning electron microscopy (SEM. The results showed that Cr(VI removal is dependent upon initial concentrations and pH. The adsorption quantity of Cr(VI onto the polymerized clay deposit followed by polymerized zeolite exhibited higher values than their original samples. The polymer-clay composite of clay deposit showed the highest removal of 76.3–100% overall initial concentrations of 10–50 mg L−1 and at initial pH of 2. Kinetics of Cr(VI removal by various sorbents was predicted using a pseudo–second order model. Our findings showed that the levels of salinity and various soluble ions (Cr2+, Na+, Cl− and SO42− in tannery wastewater are very high, and their levels were reduced after treatment, especially by polymerized sorbents. It could be concluded that the polymer-clay composites may be employed as a highly efficient sorbent for the removal of Cr(VI and toxic ions from the wastewater.

  16. Denitration of simulated high-level liquid wastes and selective removal of cesium with zeolites

    International Nuclear Information System (INIS)

    Mimura, Hitoshi; Kanno, Takuji; Kimura, Toshiya.

    1982-01-01

    Denitration of high-level liquid wastes (HLW) from nuclear fuel reprocessing has been studied. Selective removal of Cs has been also examined with various types of zeolites. The following zeolites were used in this study; Na-synthetic mordenite (NaSM), Na-natural mordenite (NaNM), Na-natural clinoptilolite (NaCP) and H-synthetic mordenites (HSM). The effective denitration is found in the simulated HLW (15 components, 2N HNO 3 soln.) containing platinum group elements in the case of the addition of formic acid, and the pH of the solution shows the value of 5.4 when the excess formic acid ([HCOOH]/[HNO 3 ] = 2.0) was added. Platinum group elements may react as a catalyst for the decomposition of nitric acid and the excess formic acid. The break-through properties of NaSM column are poor for the simulated HLW, and the selective removal of Cs appears to be difficult. On the other hand, good results are obtained in the denitrated HLW, i.e., break-through capacity, total capacity and column utilization are 59.4 (meq./100 g zeolite), 147 (meq./100 g zeolite) and 40.4 (%), respectively. The break-through properties of NaSM and NaNM are superior to those of HSM. The break-through capacity and column utilization increase with an increase in column temperature. (author)

  17. Applicability of zeolites in potassium and nitrate retention in different soil types

    Directory of Open Access Journals (Sweden)

    Pavlović Jelena B.

    2017-01-01

    Full Text Available Environmental protection and sustainable agricultural production require the use of inexpensive and environmentally acceptable soil supplements. Objectives of this study were to investigate the influence of the addition of the natural zeolite – clinoptilolite (NZ and its iron(III-modified form (FeZ on the potassium and nitrate leaching from sandy, silty loam and silty clay soils. The zeolites were added in two amounts: 0.5 (FeZ and 1.0 wt. % (NZ and FeZ. The experiments were carried out in columns organized in eight experimental systems containing unamended (control specimens and amended soils. The concentration of K+ and NO3–N in the leachates was monitored during 7 days. The obtained results indicate that the K+ and NO3–N leaching mainly depends on the soil type and pH of the soil. The NZ and FeZ addition has the highest impact on the K+ retention in the acidic sandy soil. The highest NO3–N retention is obtained with FeZ in acidic silty loam soil. The K+ leaching kinetics for all the studied soils follow the Avrami kinetics model with the parameter n < 1. This study demonstrates that NZ and FeZ can be a good soil supplement for the K+ retention for all studied soils and in the NO3–N retention for silty loam and silty clay soils. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. 172018

  18. NRC high-level radioactive waste research at CNWRA, July--December 1992

    International Nuclear Information System (INIS)

    Sagar, B.; Ababou, R.; Ahola, M.

    1993-07-01

    Progress from July 1 to December 31, 1992 on the nine NRC-sponsored research projects conducted at the Center for Nuclear Waste Regulatory Analyses is described. Ion-exchange experiments between clinoptilolite and aqueous solutions of Na + and Sr 2+ and three applications of reaction-path modeling are described in the Unsaturated Mass Transport (Geochemistry) project. Numerical simulation of a laboratory-scale non-isothermal two-phase flow is discussed in the Thermohydrology chapter. Methods for estimating rock joint roughness coefficient are the focus of the Seismic Rock Mechanics project for which the Tilt Test, Tse and Cruden's equations, and fractal-based equations were tested and found to be unsatisfactory. In the Integrated Waste Package Experiments chapter, investigations of pit initiation and repassivation potential for alloys 825 and C-22 and stainless steel 304L and 316L are described. Testing of the BIGFLOW computer code and visualization of fracture topology is the theme of the Stochastic Hydrology project. Preliminary analysis of field data from the Akrotiri site in Greece is developed in the Geochemical Analogs project. Mechanistic modeling of sorption using the MINTEQA2 code is investigated as part of the Sorption project. Adaptive gridding and ''modified equations'' methods for solving the flow and transport equations are described in the Performance Assessment chapter. Finally, the Volcanism chapter focuses on using nonhomogeneous Poisson processes for estimating probability of volcanic events at the potential repository site

  19. Effect of precipitation conditions on the magnetic and sorption properties of zeolite-maghemite composites

    International Nuclear Information System (INIS)

    Matik, M.; Pechousek, J.; Zboril, R.; Sepelak, V.

    2006-01-01

    Natural zeolite (clinoptilolite) from Nizny Hrabovec (Slovakia) has been magnetically modified through maghemite (γ-Fe 2 O 3 ) nanoparticles by precipitation route at various reaction conditions. An effect of the precipitation temperature, weight ratio of Fe/zeolite and interaction time on the magnetic and surface properties of maghemite-zeolite composites was monitored by Moessbauer spectroscopy, TEM and BET surface area measurements. A decrease in reaction time and the Fe/zeolite ratio leads to smaller particles of γ-Fe 2 O 3 while lowering the precipitation temperature results in the larger crystallites. The reflection of the precipitation temperature being the key variable in the sorption properties of composites was tested with selected heavy metal ions. The sample prepared at highest temperature of 85 grad C reveals much higher maximum sorption capacity for Pb 2+ than commonly observed for magnetically modified natural zeolites. Good ability for sorption of anions was demonstrated with AsO 4 3- , which offers new applications of such modified zeolites. The sample with the best sorption properties was characterized by SEM, XRD, in-field Moessbauer spectroscopy and magnetic measurements. Following these data, maghemite nanoparticles form aggregates, which are sorbed on zeolite inhomogeneously with some free active surface of zeolite. The particles are about 15 nm in size and reveal the partial vacancies ordering as documented through the increased ratio of tetrahedral and octahedral positions being of 1/3. FC/ZFC curves confirm strongly interacting superparamagnetic particles with a blocking temperature of 230 K. (authors)

  20. Efficient removal of cesium from low-level radioactive liquid waste using natural and impregnated zeolite minerals.

    Science.gov (United States)

    Borai, E H; Harjula, R; Malinen, Leena; Paajanen, Airi

    2009-12-15

    The objective of the proposed work was focused to provide promising solid-phase materials that combine relatively inexpensive and high removal capacity of some radionuclides from low-level radioactive liquid waste (LLRLW). Four various zeolite minerals including natural clinoptilolite (NaNCl), natural chabazite (NaNCh), natural mordenite (NaNM) and synthetic mordenite (NaSM) were investigated. The effective key parameters on the sorption behavior of cesium (Cs-134) were investigated using batch equilibrium technique with respect to the waste solution pH, contacting time, potassium ion concentration, waste solution volume/sorbent weight ratio and Cs ion concentration. The obtained results revealed that natural chabazite (NaNCh) has the higher distribution coefficients and capacity towards Cs ion rather than the other investigated zeolite materials. Furthermore, novel impregnated zeolite material (ISM) was prepared by loading Calix [4] arene bis(-2,3 naphtho-crown-6) onto synthetic mordenite to combine the high removal uptake of the mordenite with the high selectivity of Calix [4] arene towards Cs radionuclide. Comparing the obtained results for both NaSM and the impregnated synthetic mordenite (ISM-25), it could be observed that the impregnation process leads to high improvement in the distribution coefficients of Cs+ ion (from 0.52 to 27.63 L/g). The final objective in all cases was aimed at determining feasible and economically reliable solution to the management of LLRLW specifically for the problems related to the low decontamination factor and the effective recovery of monovalent cesium ion.

  1. Efficient removal of cesium from low-level radioactive liquid waste using natural and impregnated zeolite minerals

    International Nuclear Information System (INIS)

    Borai, E.H.; Harjula, R.; Malinen, Leena; Paajanen, Airi

    2009-01-01

    The objective of the proposed work was focused to provide promising solid-phase materials that combine relatively inexpensive and high removal capacity of some radionuclides from low-level radioactive liquid waste (LLRLW). Four various zeolite minerals including natural clinoptilolite (NaNCl), natural chabazite (NaNCh), natural mordenite (NaNM) and synthetic mordenite (NaSM) were investigated. The effective key parameters on the sorption behavior of cesium (Cs-134) were investigated using batch equilibrium technique with respect to the waste solution pH, contacting time, potassium ion concentration, waste solution volume/sorbent weight ratio and Cs ion concentration. The obtained results revealed that natural chabazite (NaNCh) has the higher distribution coefficients and capacity towards Cs ion rather than the other investigated zeolite materials. Furthermore, novel impregnated zeolite material (ISM) was prepared by loading Calix [4] arene bis(-2,3 naphtho-crown-6) onto synthetic mordenite to combine the high removal uptake of the mordenite with the high selectivity of Calix [4] arene towards Cs radionuclide. Comparing the obtained results for both NaSM and the impregnated synthetic mordenite (ISM-25), it could be observed that the impregnation process leads to high improvement in the distribution coefficients of Cs + ion (from 0.52 to 27.63 L/g). The final objective in all cases was aimed at determining feasible and economically reliable solution to the management of LLRLW specifically for the problems related to the low decontamination factor and the effective recovery of monovalent cesium ion.

  2. Studies on simulated nuclear waste of mixed solvent type

    International Nuclear Information System (INIS)

    Aggarwal, S.

    1989-09-01

    Caesium 137, strontium 90 and ruthenium 106 are among the longest lived fission products present in reprocessing wastes and are therefore considered to be a long term hazard to the environment. A method for removal of 137-Cs, 90-Sr and 106-Ru from the nuclear waste is by ion-exchange and sorption. Radiochemical methods were employed to investigate the uptake of 137-Cs, 90-Sr and 106-Ru by synthetic type A, X, Y, zeolites and by mordenite and clinoptilolite. The solvents employed were tributylphosphate (TBP) and kerosene (OK). The dependence of the exchange process on time was studied at room temperature. The exchange equilibrium was strongly dependent on time during the first hour but then attained equilibrium. It was also noted that the distribution coefficient (Kd) values for 137-Cs were higher than those for 90-Sr which were higher than those for 106-Ru. Thus the order of extraction was: 137-Cs > 90-Sr > 106-Ru. Ethanol was also used as the solvent to see the effect on the Kds by varying the amount of water present, i.e. from 0% water to 10% water. It was observed that the Kd increased with an increase in water content. The effect of pH and different ratios of TBP:OK were also studied. There was no relationship between the Kds and the different ratios. Some work was also done on the adsorption of 137-Cs on cements and cement phases. The sorption of 137-Cs on to all types of cements was low. (author)

  3. [Characteristics and comparative study of a new drinking-water defluoridation adsorbent Bio-F].

    Science.gov (United States)

    Zhu, Chi; Zhao, Liang-Yuan; Yuan, Heng; Yang, Han-Ying; Li, Ang; Wang, Peng; Yang, Shao

    2009-04-15

    To evaluate the application potentiality pf a new type drinking-water defluoridation adsorbent Bio-F, comparative study on the defluoridation characteristics of common adsorbents activated alumina (AA), bone char (BC), activated clinoptilolite (AC) with Bio-F was conducted. The defluoridation characteristics under different conditions, such as particle diameter, pH, retention time, fluorine concentration, regeneration stability, were investigated by continuous-flow column experiments and static tests. The defluoridation efficiency of high fluoride underground water by four types of adsorbents was also compared. The results showed that F(-) adsorption kinetics of Bio-F fitted the Lagergren First-order equation (R2 = 0.9580). F(-) adsorption by Bio-F was found to fit the Langmuir adsorption isotherm (R2 = 0.9992). The results indicated that the static defluoridation capacity (DC) of Bio-F was 4.0883 mg x g(-1), which was about 1.8 folds and 5.8 folds of those of AA and AC respectively. DC of all four adsorbents was positively correlated with F(-) concentration and negatively correlated with particle size. High concentration of CO3(2-) and HCO3(-) reduced the DC of Bio-F (p retention time of Bio-F was 3-4 min, which was less than that of AC (20 min) and AA (11 min). The DC of Bio-F remained relatively stable in pH 4.0-9.0 and in regeneration since the DC variation was not more than 15%. The above results indicated that Bio-F was superior to AA, BC and AC in drinking-water defluoridation.

  4. Common Ion Effects In Zeoponic Substrates: Dissolution And Cation Exchange Variations Due to Additions of Calcite, Dolomite and Wollastonite

    Science.gov (United States)

    Beiersdorfer, R. E.; Ming, D. W.; Galindo, C., Jr.

    2003-01-01

    c1inoptilolite-rich tuff-hydroxyapatite mixture (zeoponic substrate) has the potential to serve as a synthetic soil-additive for plant growth. Essential plant macro-nutrients such as calcium, phosphorous, magnesium, ammonium and potassium are released into solution via dissolution of the hydroxyapatite and cation exchange on zeolite charged sites. Plant growth experiments resulting in low yield for wheat have been attributed to a Ca deficiency caused by a high degree of cation exchange by the zeolite. Batch-equilibration experiments were performed in order to determine if the Ca deficiency can be remedied by the addition of a second Ca-bearing, soluble, mineral such as calcite, dolomite or wollastonite. Variations in the amount of calcite, dolomite or wollastonite resulted in systematic changes in the concentrations of Ca and P. The addition of calcite, dolomite or wollastonite to the zeoponic substrate resulted in an exponential decrease in the phosphorous concentration in solution. The exponential rate of decay was greatest for calcite (5.60 wt. % -I), intermediate for wollastonite (2.85 wt.% -I) and least for dolomite (1.58 wt.% -I). Additions of the three minerals resulted in linear increases in the calcium concentration in solution. The rate of increase was greatest for calcite (3.64), intermediate for wollastonite (2.41) and least for dolomite (0.61). The observed changes in P and Ca concentration are consistent with the solubilities of calcite, dolomite and wollastonite and with changes expected from a common ion effect with Ca. Keywords: zeolite, zeoponics, common-ion effect, clinoptilolite, hydroxyapatite

  5. Anomalous solute transport in saturated porous media: Relating transport model parameters to electrical and nuclear magnetic resonance properties

    Science.gov (United States)

    Swanson, Ryan D; Binley, Andrew; Keating, Kristina; France, Samantha; Osterman, Gordon; Day-Lewis, Frederick D.; Singha, Kamini

    2015-01-01

    The advection-dispersion equation (ADE) fails to describe commonly observed non-Fickian solute transport in saturated porous media, necessitating the use of other models such as the dual-domain mass-transfer (DDMT) model. DDMT model parameters are commonly calibrated via curve fitting, providing little insight into the relation between effective parameters and physical properties of the medium. There is a clear need for material characterization techniques that can provide insight into the geometry and connectedness of pore spaces related to transport model parameters. Here, we consider proton nuclear magnetic resonance (NMR), direct-current (DC) resistivity, and complex conductivity (CC) measurements for this purpose, and assess these methods using glass beads as a control and two different samples of the zeolite clinoptilolite, a material that demonstrates non-Fickian transport due to intragranular porosity. We estimate DDMT parameters via calibration of a transport model to column-scale solute tracer tests, and compare NMR, DC resistivity, CC results, which reveal that grain size alone does not control transport properties and measured geophysical parameters; rather, volume and arrangement of the pore space play important roles. NMR cannot provide estimates of more-mobile and less-mobile pore volumes in the absence of tracer tests because these estimates depend critically on the selection of a material-dependent and flow-dependent cutoff time. Increased electrical connectedness from DC resistivity measurements are associated with greater mobile pore space determined from transport model calibration. CC was hypothesized to be related to length scales of mass transfer, but the CC response is unrelated to DDMT.

  6. Direct geoelectrical evidence of mass transfer at the laboratory scale

    Science.gov (United States)

    Swanson, Ryan D.; Singha, Kamini; Day-Lewis, Frederick D.; Binley, Andrew; Keating, Kristina; Haggerty, Roy

    2012-10-01

    Previous field-scale experimental data and numerical modeling suggest that the dual-domain mass transfer (DDMT) of electrolytic tracers has an observable geoelectrical signature. Here we present controlled laboratory experiments confirming the electrical signature of DDMT and demonstrate the use of time-lapse electrical measurements in conjunction with concentration measurements to estimate the parameters controlling DDMT, i.e., the mobile and immobile porosity and rate at which solute exchanges between mobile and immobile domains. We conducted column tracer tests on unconsolidated quartz sand and a material with a high secondary porosity: the zeolite clinoptilolite. During NaCl tracer tests we collected nearly colocated bulk direct-current electrical conductivity (σb) and fluid conductivity (σf) measurements. Our results for the zeolite show (1) extensive tailing and (2) a hysteretic relation between σf and σb, thus providing evidence of mass transfer not observed within the quartz sand. To identify best-fit parameters and evaluate parameter sensitivity, we performed over 2700 simulations of σf, varying the immobile and mobile domain and mass transfer rate. We emphasized the fit to late-time tailing by minimizing the Box-Cox power transformed root-mean square error between the observed and simulated σf. Low-field proton nuclear magnetic resonance (NMR) measurements provide an independent quantification of the volumes of the mobile and immobile domains. The best-fit parameters based on σf match the NMR measurements of the immobile and mobile domain porosities and provide the first direct electrical evidence for DDMT. Our results underscore the potential of using electrical measurements for DDMT parameter inference.

  7. Sorption of nonpolar aromatic contaminants by chlorosilane surface modified natural minerals.

    Science.gov (United States)

    Huttenloch, P; Roehl, K E; Czurda, K

    2001-11-01

    The efficacy of the surface modification of natural diatomite and zeolite material by chlorosilanes is demonstrated. Chlorosilanes used were trimethylchlorosilane (TMSCI), tert-butyldimethylchlorosilane (TBDMSCI), dimethyloctadecylchlorosilane (DMODSCI), and diphenyldichlorosilane (DPDSCI) possessing different headgroups and chemical properties. Silanol groups of the diatomite and zeolite were modified by chemical reaction with the chlorosilanes resulting in a stable covalent attachment of the organosilanes to the mineral surface. The alteration of surface properties of the modified material was proved by measurements of water adsorption capacity, total organic carbon (TOC) content, and thermoanalytical data. The surface modified material showed great stability even when exposed to extremes in ionic strength, pH, and to pure organic solvents. Sorption of toluene, o-xylene, and naphthalene from water was greatly enhanced by the surface modification compared to the untreated materials which showed no measurable sorption of these compounds. The enhanced sorption was dependent on the organic carbon content as well as on chemical characteristics of the chlorosilanes used. Batch sorption experiments showed that the phenyl headgroups of DPDSCI have the best affinity for aromatic compounds. Removal from an aqueous solution of 10 mg/L of naphthalene, o-xylene, and toluene was 71%, 60%, and 30% for surface modified diatomite and 51%, 30%, and 16% for modified clinoptilolite, respectively. Sorption data were well described by the Freundlich isotherm equation, which indicated physical adsorption onto the lipophilic surface rather than partitioning into the surface organic phase. The chlorosilane modified materials have an apparent potential for application in environmental technologies such as permeable reactive barriers (PRB) or wastewater treatment.

  8. Preliminary stratigraphic and petrologic characterization of core samples from USW-G1, Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Waters, A.C.; Carroll, P.R.

    1981-11-01

    Tuffs of the Nevada Test Site are currently under investigation to determine their potential for long-term storage of radioactive waste. As part of this program, hole USW-G1 was drilled to a depth of 6000 ft below the surface, in the central part of the Yucca Mountain area, Nevada Test Site, Nevada. Petrographic study of the USW-G1 core is presented in this report and shows the tuffs (which generally were variably welded ash flows) are partly recrystallized to a variety of secondary minerals. The important alteration products are zeolites (heulandite, clinoptilolite, mordenite and analcime), smectite clays with minor interstratified illite, albite, micas, potassium feldspar, and various forms of silica. Iijima's zeolite zones I through IV of burial metamorphism can be recognized in the core. Zeolites are first observed at about the 1300-ft depth, and the high-temperature boundary of zeolite stability in this core occurs at about 4350 ft. Analcime persists, either metastably or as a retrograde mineral, deeper in the core. The oxidation state of Fe-Ti oxide minerals, through most of the core, increases as the degree of welding decreases, but towards the bottom of the hole, reducing conditions generally prevail. Four stratigraphic units transected by the core may be potentially favorable sites for a waste repository. These four units, in order of increasing depth in the core, are (1) the lower cooling unit of the Topopah Spring Member, (2) cooling unit II of the Bullfrog Member, (3) the upper part of the Tram tuff, and (4) the Lithic-rich tuff

  9. Estimación de propiedades termodinámicas de silicatos. Construcción de diagramas de actividad de zeolitas

    Directory of Open Access Journals (Sweden)

    La Iglesia, A.

    1995-12-01

    Full Text Available In this paper we analyze the present methods of estimation of the thermodynamic properties of silicates with special emphasis on the free energy and enthalpy of zeolites. These data are not available in the literature, as these phases are chemically complexo The obtained values allow us to build the 10 following thermodynamic equilibrium diagrams: solubility of laumontite, chabazite, analcime, volcanic glass, zeolite A and zeolite X, and stability diagrams of chabazite-analcime-phillipsite-volcanic glass, clinoptilolite-phillipsite-erionite, prehnite-laumontite-heulandite, and kaolinite-metakaolinhidrosodalite-zeolite A. These diagrams can be useful to understand the genesis of these minerals and the processes that allow their formation in the laboratory.En este artículo se pasa revista a los métodos actuales de estimación de propiedades termodinámicas de silicatos, haciendo especial énfasis a los dedicados a la estimación de la energía libre de formación y de la entalpía de zeolitas, datos poco disponibles en la bibliografía debido a la complejidad química de estas fases. Los valores obtenidos han permitido construir los 10 diagramas de equilibrio termodinámico siguientes: diagramas de solubilidad de laumontita, chabazita, analcima, vidrio volcánico, zeolita A y zeolita X y los de estabilidad de chabazita-analcima-philipsitavidrio volcánico, clinoptilolita-philipsita-erionita, prehnita-laumontita-heulandita y caolinita-metacaolinita-hidrosodalita-zeolita A. Estos diagramas pueden explicar la génesis de los minerales o los procesos que dan lugar a su síntesis en el laboratorio.

  10. Preliminary stratigraphic and petrologic characterization of core samples from USW-G1, Yucca Mountain, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Waters, A.C.; Carroll, P.R. (eds.)

    1981-11-01

    Tuffs of the Nevada Test Site are currently under investigation to determine their potential for long-term storage of radioactive waste. As part of this program, hole USW-G1 was drilled to a depth of 6000 ft below the surface, in the central part of the Yucca Mountain area, Nevada Test Site, Nevada. Petrographic study of the USW-G1 core is presented in this report and shows the tuffs (which generally were variably welded ash flows) are partly recrystallized to a variety of secondary minerals. The important alteration products are zeolites (heulandite, clinoptilolite, mordenite and analcime), smectite clays with minor interstratified illite, albite, micas, potassium feldspar, and various forms of silica. Iijima`s zeolite zones I through IV of burial metamorphism can be recognized in the core. Zeolites are first observed at about the 1300-ft depth, and the high-temperature boundary of zeolite stability in this core occurs at about 4350 ft. Analcime persists, either metastably or as a retrograde mineral, deeper in the core. The oxidation state of Fe-Ti oxide minerals, through most of the core, increases as the degree of welding decreases, but towards the bottom of the hole, reducing conditions generally prevail. Four stratigraphic units transected by the core may be potentially favorable sites for a waste repository. These four units, in order of increasing depth in the core, are (1) the lower cooling unit of the Topopah Spring Member, (2) cooling unit II of the Bullfrog Member, (3) the upper part of the Tram tuff, and (4) the Lithic-rich tuff.

  11. Fracture coatings in Topopah Spring Tuff along drill hole wash

    International Nuclear Information System (INIS)

    Carlos, B.A.; Chipera, S.J.; Bish, D.L.

    1994-01-01

    Fracture-lining minerals are being studied as part of site characterization to determine the suitability of Yucca Mountain, Nevada as a potential high level nuclear waste repository. Fracture coatings in the Paintbrush Group provide information on potential flow paths above the water table both toward and away from the potential repository and provide information on the distribution of fracture-lining minerals needed to model thermal effects of waste emplacement. Fracture coatings within the predominantly non-zeolitic Paintbrush Group vary both with depth and laterally across Yucca Mountain, whereas fracture coatings in tuffs below the Paintbrush Group are related to the mineralogy of the tuffs and follow a consistent pattern of distribution with predominantly quartz, calcite, and manganese oxides in the devitrified intervals and mordenite and clinoptilolite in the zeolitic intervals. The zeolites stellerite and heulandite are more abundant in fractures in the Topopah Spring Tuff in drill holes USW G-1 and UE-25 a number-sign l, located along Drill Hole Wash (at the northern end of Yucca Mountain) than in core from other parts of Yucca Mountain. Buesch et al. (2) present evidence for a complex fault system along Drill Hole Wash. To investigate the possibility that the abundant fracture-lining zeolites in USW G-1 and UE-25 a number-sign 1 are related to the Drill Hole Wash fault, the Topopah Spring Tuff was examined in drill cores from USW UZ-14, USW G-1, USW NRG-7/7a, and UE-25 a number-sign l

  12. Cost-effective treatment of swine wastes through recovery of energy and nutrients.

    Science.gov (United States)

    Amini, Adib; Aponte-Morales, Veronica; Wang, Meng; Dilbeck, Merrill; Lahav, Ori; Zhang, Qiong; Cunningham, Jeffrey A; Ergas, Sarina J

    2017-11-01

    Wastes from concentrated animal feeding operations (CAFOs) are challenging to treat because they are high in organic matter and nutrients. Conventional swine waste treatment options in the U.S., such as uncovered anaerobic lagoons, result in poor effluent quality and greenhouse gas emissions, and implementation of advanced treatment introduces high costs. Therefore, the purpose of this paper is to evaluate the performance and life cycle costs of an alternative system for treating swine CAFO waste, which recovers valuable energy (as biogas) and nutrients (N, P, K + ) as saleable fertilizers. The system uses in-vessel anaerobic digestion (AD) for methane production and solids stabilization, followed by struvite precipitation and ion exchange (IX) onto natural zeolites (chabazite or clinoptilolite) for nutrient recovery. An alternative approach that integrated struvite recovery and IX into a single reactor, termed STRIEX, was also investigated. Pilot- and bench-scale reactor experiments were used to evaluate the performance of each stage in the treatment train. Data from these studies were integrated into a life cycle cost analysis (LCCA) to assess the cost-effectiveness of various process alternatives. Significant improvement in water quality, high methane production, and high nutrient recovery (generally over 90%) were observed with both the AD-struvite-IX process and the AD-STRIEX process. The LCCA showed that the STRIEX system can provide considerable financial savings compared to conventional systems. AD, however, incurs high capital costs compared to conventional anaerobic lagoons and may require larger scales to become financially attractive. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. An integrated remediation system using synthetic and natural zeolites for treatment of wastewater and contaminated sediments

    International Nuclear Information System (INIS)

    Rios Reyes, Carlos; Appasamy, Danen; Clive, Roberts

    2011-01-01

    The major sources of water pollution can be classified as municipal, industrial, and agricultural. Different types of polluted aqueous effluents and sediments may be produced, which contain relatively high levels of heavy metals. During the 1990s, the large-scale development of constructed wetlands around the world drew much attention from public and environmental groups. The present study looks at the use of an integrated remediation system using zeolites for the treatment of wastewater and sediments. Zeolites have been widely studied in the past 10 years due to their attractive properties such as molecular-sieving, high cation exchange capacities, and their affinity for heavy metals. Coal industry by-products-based zeolites (faujasite type) have been tested as an effective and low-cost novel alternative for wastewater treatment, particularly their removing of heavy metals. On the other hand, a preliminary laboratory-scale experiment was conducted on the use of natural zeolites (clinoptilolite type) for the retention of heavy metals from canal sediments. Experimental work revealed promising results, which could be replicated on a bigger scale. Although this has been developed for canal sediments, the remediation strategy can be adapted to different waterways such as rivers. The development of the proposed remediation system in a specific experimental site as the major part of an innovation park can provide great benefits to a population living near contaminated effluents. It provides not only opportunities for the mitigation of environmental impact, improving water quality and landscape amenity, but also allows for several recreational opportunities

  14. Antibacterial properties of Ag-exchanged Philippine natural zeolite-chitosan composites

    Science.gov (United States)

    Taaca, Kathrina Lois M.; Olegario, Eleanor M.; Vasquez, Magdaleno R.

    2017-12-01

    Zeolites are microporous minerals composed of silicon, aluminum and oxygen. These aluminosilicates consist of tetrahedral units which produce open framework structures to generate a system of pores and cavities of molecular dimensions. Zeolites are naturally abundant and can be mined in most parts of the world. In this study, natural zeolites (NaZ) which are locally-sourced here in the Philippines were investigated to determine its properties. An ion-exchange process was utilized, using the zeolite to silver (Ag) solution ratio of 1:20 (w/v), to incorporate Ag into the zeolite framework. Characterizations such as XRD, AAS, and Agar diffusion assay were used to evaluate the properties of the synthesized Ag-exchanged zeolites (AgZ). X-ray diffraction revealed that both NaZ and AgZ have peaks mostly corresponding to the clinoptilolite structure, with some trace peaks of the mordenite and quartz. Absorption spectroscopy revealed that the ion exchange process added about 0.61188g of silver into the zeolite structure. This Ag content was seen to be enough to make the AgZ sample exhibit an antibacterial effect where clearing zones against E. coli and S. aureus were observed in the agar diffusion assay, respectively. The AgZ sample was also tested as ceramic filler to a polymer matrix-chitosan. The diffusion assay revealed presence of antibacterial activity to the polymer composite with AgZ fillers. These results indicate that the Philippine natural zeolite, incorporated with metals such as Ag, can be used as an antibacterial agent and can be developed as a ceramic filler to improve the antibacterial property of composite materials for biomedical application.

  15. Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: The influence of zeolite chemical surface characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Alejandro, Serguei [Laboratorio de Tecnologías Limpias (F. Ingeniería), Universidad Católica de la Santísima Concepción, Alonso de Ribera 2850, Concepción (Chile); Núcleo de Energías Renovables (F. Ingeniería), Universidad Católica de Temuco, Rudecindo Ortega 02950, Temuco (Chile); Valdés, Héctor, E-mail: hvaldes@ucsc.cl [Laboratorio de Tecnologías Limpias (F. Ingeniería), Universidad Católica de la Santísima Concepción, Alonso de Ribera 2850, Concepción (Chile); Manéro, Marie-Hélène [Université de Toulouse (France); INPT, UPS (France); Laboratoire de Génie Chimique, 4, Allée Emile Monso, F–31030 Toulouse (France); CNRS (France); Laboratoire de Génie Chimique, F–31030 Toulouse (France); Zaror, Claudio A. [Departamento de Ingeniería Química (F. Ingeniería), Universidad de Concepción, Concepción, Correo 3, Casilla 160–C (Chile)

    2014-06-01

    Highlights: • Surface acidity of modified natural zeolite is related to its chemical reactivity. • Brønsted acid sites are associated to toluene adsorption. • Lewis acid sites could decompose ozone generating surface active oxygen species. • Infrared spectra evidence active atomic oxygen and oxidation by-product formation. • 2NH4Z1 sample shows the highest reactivity toward adsorbed toluene. - Abstract: In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823 K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623 K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity.

  16. Zeolitization of intracaldera sediments and rhyolitic rocks in the 1.25 Ma lake of Valles caldera, New Mexico, USA

    Science.gov (United States)

    Chipera, Steve J.; Goff, Fraser; Goff, Cathy J.; Fittipaldo, Melissa

    2008-12-01

    Quantitative X-ray diffraction analysis of about 80 rhyolite and associated lacustrine rocks has characterized previously unrecognized zeolitic alteration throughout the Valles caldera resurgent dome. The alteration assemblage consists primarily of smectite-clinoptilolite-mordenite-silica, which replaces groundmass and fills voids, especially in the tuffs and lacustrine rocks. Original rock textures are routinely preserved. Mineralization typically extends to depths of only a few tens of meters and resembles shallow "caldera-type zeolitization" as defined by Utada et al. [Utada, M., Shimizu, M., Ito, T., Inoue, A., 1999. Alteration of caldera-forming rocks related to the Sanzugawa volcanotectonic depression, northeast Honshu, Japan — with special reference to "caldera-type zeolitization." Resource Geol. Spec. Issue No. 20, 129-140]. Geology and 40Ar/ 39Ar dates limit the period of extensive zeolite growth to roughly the first 30 kyr after the current caldera formed (ca. 1.25 to 1.22 Ma). Zeolitic alteration was promoted by saturation of shallow rocks with alkaline lake water (a mixture of meteoric waters and degassed hydrothermal fluids) and by high thermal gradients caused by cooling of the underlying magma body and earliest post-caldera rhyolite eruptions. Zeolitic alteration of this type is not found in the later volcanic and lacustrine rocks of the caldera moat (≤ 0.8 Ma) suggesting that later lake waters were cooler and less alkaline. The shallow zeolitic alteration does not have characteristics resembling classic, alkaline lake zeolite deposits (no analcime, erionite, or chabazite) nor does it contain zeolites common in high-temperature hydrothermal systems (laumontite or wairakite). Although aerially extensive, the early zeolitic alteration does not form laterally continuous beds and are consequently, not of economic significance.

  17. Increased photocatalytic activity of NiO and ZnO in photodegradation of a model drug aqueous solution: Effect of coupling, supporting, particles size and calcination temperature

    Energy Technology Data Exchange (ETDEWEB)

    Derikvandi, Hadis [Department of Chemistry, Shahreza Branch, Islamic Azad University, P.O. Box 311-86145, Shahreza, Isfahan, Iran (Iran, Islamic Republic of); Young Researchers and Elite Club, Shahreza Branch, Islamic Azad University, Shahreza (Iran, Islamic Republic of); Nezamzadeh-Ejhieh, Alireza, E-mail: arnezamzadeh@iaush.ac.ir [Department of Chemistry, Shahreza Branch, Islamic Azad University, P.O. Box 311-86145, Shahreza, Isfahan, Iran (Iran, Islamic Republic of); Young Researchers and Elite Club, Shahreza Branch, Islamic Azad University, Shahreza (Iran, Islamic Republic of); Razi Chemistry Research Center (RCRC), Shahreza Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of)

    2017-01-05

    Highlights: • Increased photoactivity of hybridized/supported NiO-ZnO whit respect to monocomponent one. • Strong dependence of photocatalytic activity of NiO-ZnO to calcination temperature. • Calcination temperature varied the crystallite forms of the semiconductors. • Red shifts in band gaps of the supported coupled semiconductors whit respect to monocomponent one. - Abstract: Mechanically ball-mill prepared clinoptilolite nanoparticles (NC) were used for increasing photocatalytic activity of NiO and ZnO as alone and binary systems. The semiconductors were supported onto the zeolite during calcination of Ni(II)-Zn(II)-exchanged NC at different calcinations temperatures. XRD, FTIR, SEM-EDX, X-ray mapping, DRS, TEM and BET techniques were used for characterization of the samples. The calcined catalysts at 400 °C for 4 h showed the best photocatalytic activity for metronidazole (MNZ) in aqueous solution. The mole ratio of ZnO/NiO affected the photodegradation efficiency because activity of the coupled catalysts depends to the both e/h production and electron scavenging processes. In the used system, NiO acted as e/h production source and ZnO as an electron sink. Red shifts in band gaps of the supported coupled semiconductors was observed whit respect to monocomponent one, confirming formation of nanoparticles of the semiconductors onto the zeolitic bed. The best activities were obtained for the NiO{sub 1.3}–ZnO{sub 1.5}/NC (NZ-NC) and NiO{sub 0.7}–ZnO{sub 4.3}/NC (NZ{sub 3}-NC) catalysts at pH 3, 1.2 g L{sup −1} of the catalysts and 1 g L{sup −1} of MNZ.

  18. Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: The influence of zeolite chemical surface characteristics

    International Nuclear Information System (INIS)

    Alejandro, Serguei; Valdés, Héctor; Manéro, Marie-Hélène; Zaror, Claudio A.

    2014-01-01

    Highlights: • Surface acidity of modified natural zeolite is related to its chemical reactivity. • Brønsted acid sites are associated to toluene adsorption. • Lewis acid sites could decompose ozone generating surface active oxygen species. • Infrared spectra evidence active atomic oxygen and oxidation by-product formation. • 2NH4Z1 sample shows the highest reactivity toward adsorbed toluene. - Abstract: In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823 K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623 K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity

  19. Genesis of uranium deposits of the Tono Mine, Japan

    International Nuclear Information System (INIS)

    Katayama, N.; Kubo, K.; Hirono, S.

    1974-01-01

    The uranium deposits of the Tono mine, Gifu Prefecture, Japan, occur in the basal part of the Toki group of Miocene age, and are distributed in the tributaries or at the head of channels on the plane of unconformity under the formation. These features characterize the basal ground-water type of uranium deposit, and they are unique in that their typical ore mineral is a zeolite of the heulandite-clinoptilolite group, uranium being adsorbed in it. The paper presents the history of formation of the Tsukiyoshi deposits, the most intensely explored in the Tono mine. The matrices of conglomerates and sandstones of the Toki group usually contain tuffaceous material, which has been montmorillonitized or zeolitized diagenetically. The conduit of uranium-bearing ground waters that migrated from the basement granites into the Tertiary sediments was controlled by the impermeable barriers, which are rocks in which montmorillonite predominated, or by the Tsukiyoshi fault, as well as by channel structures. Where the waters became rather stagnant, uranium was adsorbed in zeolite from them. Enrichment of uranium further proceeded locally as follows. Pyrite was oxidized to produce sulphuric acid solution which leached the uranium that had been adsorbed in zeolite. The pH of the uranium-rich solution became higher and higher in the course of migration and, as soon as it reached about 4, the uranium in the solution was again adsorbed in zeolite, the uranium content of which may have been enriched up to 0.9%. Coffinites have been formed where uranium was accumulated over the adsorption capacity of zeolite or where strongly reducing conditions were maintained by carbonaceous matter. (author)

  20. Selectivity of the adsorption process of modified zeolite rock with hexadecyl trimethylammonium bromide in front to chromates and dichromates

    International Nuclear Information System (INIS)

    Salgado G, N.

    2011-01-01

    In the present investigation natural zeolite (clinoptilolite) from the Chihuahua state, which was conditioned with sodium chloride solution and subsequently modified with a hexadecyl trimethylammonium bromide solution was used to evaluate the removal of Cr (Vi) from chromate or dichromate solutions. The zeolite materials were characterized by scanning electron microscopy and X-ray diffraction. The surface area was also determined. The experiments were performed in a batch system, the influence of ph, contact time between phases were investigated and during the adsorption process was calculated the concentration of chromium ion present in aqueous solution (CrO 4 2- , Cr 2 O 7 2- ). The quantification of chromium removed from the aqueous solution by atomic absorption spectrometry technique was done. In order to understand the behaviour of the adsorption kinetics the pseudo first and pseudo second order models were applied, and to determine the adsorption capacity of the zeolite materials for Cr the Langmuir, Freundlich and Langmuir-Freundlich models were chosen. It was found that the removal efficiency of chromium ion is influenced by ph and the chemical species present: chromate or dichromate. The chromate and dichromate sorption kinetic data were best fitted to the pseudo-second and pseudo-first order models, respectively; and the Langmuir and Langmuir-Freundlich models described adequately the isotherms data considering a mono component system. In a mixture of Cr (Vi) ad CrO 4 2- and Cr 2 O 7 2- , the surfactant modified zeolite has a greater selectivity for Cr 2 O 7 2- ion than CrO 4 2- . In this case the Langmuir-Freundlich model described the adsorption isotherm behavior. (Author)

  1. Mineralogy, geochemistry and low grade metamorphism of green tuffs of Karaj formation in Hesarbon area (south west Firoozkooh

    Directory of Open Access Journals (Sweden)

    Shiva Bahrami

    2017-03-01

    Full Text Available Green tuffs of middle Eocene age in Hesarbon area, south west of Firoozkuh (East of Central Alborz consist of a thick sequence of lithic-, crystal-,vitric-and calcareous-tuffs. Microscopic and x-ray diffraction studies show plagioclase (albite and oligoclase, alkali feldspar (sanidine, quartz, cristobalite, biotite and hornblende are the major minerals in the rocks studied. Secondary minerals such as analcime, chlorite, prehnite and clay minerals are mainly present in the groundmass of the rocks. Extensive tectonic activities have created a variety of structural features including numerous folds and faults and therefore, have caused the green tuffs to be crushed and converted to breccia tuffs in many parts. Veins and cavities are filled by considerable amounts of zeolitic minerals including heulandite group, clinoptilolite and natrolite along with calcite and secondary quartz. Based on geochemical data, they lie on the dacite and rhyodacite field showing a calc-alkaline nature in the corresponding diagrams. According to the chondrite and primitive mantle normalized diagrams of trace elements, negative anomalies of Eu, Nb, Ti, P and depletion of HFSE together with their position in the petrogenesis discrimination diagrams, it is most likely that these rocks are formed in the active continental margin of a subduction zone. The existence of analcime and prehnite in the groundmass demonstrate that these rocks have undergone some degrees of low-grade metamorphism due to the overburden of the layers in the temperature range 200-300 °C. The present study shows that zeolite minerals filling the fractures and cavities of tuffs are precipitated by hydrothermal fluids with a neutral pH to acidic

  2. Seawater-sediment interaction at elevated temperatures and pressures: implications for the near field chemical environment

    International Nuclear Information System (INIS)

    Seyfried, W.E. Jr.; Thornton, E.C.; Janecky, D.R.

    1981-01-01

    Results of four experiments are reported which document chemical exchange and mineralogic modification during seawater-sediment interaction at 200 0 to 300 0 C, 500 bars. Sediments used for this study are from MPG-1 (central North Pacific). Experimental conditions (T, P, W/R) were chosen to be reasonably analogous to conditions which will characterize the near field environment; that is a zone within approximately 1 m of the buried waste canister. In general, the major element chemistry of seawater was similarly modified in all experiments. The aqueous concentrations of Ca, Mg, Sr, and SO 4 decreased and SiO 2 /sub (aq)/, Na, K, and ΣCO 2 increased relative to values in seawater prior to reaction with sediments. pH decreased and remained distinctly acid. Con comitantly significant concentrations of heavy metals entered seawater from the sediments during reaction. Dissolution of Mn-rich phases profoundly affected alteration processes. For example, reaction of MnO 2 components of the smectite-rich sediment (Pacific smectite) with seawater created an unusually oxidizing milieu (fO 2 = 10 -7 74 ), and resulted in dissolution of significant quantities of Au from the reaction cell. Although illite-quartz-Fe-chlorite (sediment B)-seawater interaction also created a relatively oxidizing environment, this environment was not capable of oxidizing Au. Thus, in this regard (oxidation potential) sediment mineralogy exerts a strong influence. Mineralogic modification of sediment B at 200 0 and 300 0 C was minor and characterized by partial dissolution of illite and exchange of Fe for Mg in chlorite. In contrast the smectite-rich sediment, which, prior to reaction with seawater contained a poorly crystalline smectite phase, clinoptilolite, and amorphous material, recrystallized totally to a well defined smectite mineral. Anhydrite was abundantly present amongst the alteration products of all experiments

  3. Copper removal using bio-inspired polydopamine coated natural zeolites

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Yang; Shapter, Joseph G. [Flinders Centre for Nanoscale Science and Technology, School of Chemical and Physical Sciences, Flinders University, Sturt Road, Bedford Park, Adelaide 5042, SA (Australia); Popelka-Filcoff, Rachel [School of Chemical and Physical Sciences, Flinders University, Sturt Road, Bedford Park, Adelaide 5042, SA (Australia); Bennett, John W. [Centre for Nuclear Applications, Australian Nuclear Science and Technology Organisation, Lucas Heights 2234, NSW (Australia); Ellis, Amanda V., E-mail: Amanda.Ellis@flinders.edu.au [Flinders Centre for Nanoscale Science and Technology, School of Chemical and Physical Sciences, Flinders University, Sturt Road, Bedford Park, Adelaide 5042, SA (Australia)

    2014-05-01

    Highlights: • Natural zeolites were modified with bio-inspired polydopamine. • A 91.4% increase in Cu(II) ion adsorption capacity was observed. • Atomic absorption and neutron activation analysis gave corroborative results. • Neutron activation analysis was used to provide accurate information on 30+ elements. • Approximately 90% of the adsorbed copper could be recovered by 0.1 M HCl treatment. - Abstract: Herein, for the first time, natural clinoptilolite-rich zeolite powders modified with a bio-inspired adhesive, polydopamine (PDA), have been systematically studied as an adsorbent for copper cations (Cu(II)) from aqueous solution. Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA) revealed successful grafting of PDA onto the zeolite surface. The effects of pH (2–5.5), PDA treatment time (3–24 h), contact time (0 to 24 h) and initial Cu(II) ion concentrations (1 to 500 mg dm{sup −3}) on the adsorption of Cu(II) ions were studied using atomic absorption spectroscopy (AAS) and neutron activation analysis (NAA). The adsorption behavior was fitted to a Langmuir isotherm and shown to follow a pseudo-second-order reaction model. The maximum adsorption capacities of Cu(II) were shown to be 14.93 mg g{sup −1} for pristine natural zeolite and 28.58 mg g{sup −1} for PDA treated zeolite powders. This impressive 91.4% increase in Cu(II) ion adsorption capacity is attributed to the chelating ability of the PDA on the zeolite surface. Furthermore studies of recyclability using NAA showed that over 50% of the adsorbed copper could be removed in mild concentrations (0.01 M or 0.1 M) of either acid or base.

  4. THE PREPARATION OF MAGNETICALLY MODIFIED SYNTHETETIC AND NATURAL ZEOLITES AND COMPARISON OF THEIR SOME PHYSICAL PROPERTIES

    Directory of Open Access Journals (Sweden)

    Zafer DİKMEN

    2013-06-01

    Full Text Available In this study, magnetically modified zeolites (MMZ has been produced and their adsorption, ion-exchange and magnetic properties have been studied. In this study, natural zeolite mineral, clinoptilolite, which belongs to Gördes (Manisa regions and synthetic 13X zeolite, which has been produced by Sigma-Aldrich firm have been used. In order to modify the surface of these minerals, magnetite sample which belongs to Divriği (Sivas region has been used. The engagement of magnetite particles on zeolite particles has been studied. For this reason, measuring, visualization and analysis techniques as DTA-TG, XRD, XRF, SEM and EDX have been used. As a result of these procedures, it has been observed that magnetite particles get engaged on the surface of zeolite particles and magnetite contribu-tion on MMZ has changed adsorption, ion-exchange and magnetic properties.In order to determine how magnetite contribution affects adsorption, ion exchange and magnetic properties of MMZ, weightily magnetite contribution ratio (zeolite/magnetite has been applied in three different forms (1/1, 1/2, 1/3.As a result of nitrogen adsorption of MMZ, it has been observed that as the weightily magnetite contribution ratio goes up, specific surface area goes down and average pore diameter rises. It has been identified that total cation exchange capacity rises as the weightily magnetite contribution ratio goes up. It has been observed that pure zeolites, which have no magnetic properties, as a result of magnetically modification process, they have got magnetically character, and they change their magnetic properties positively as the weightily magnetite contribution goes up. It has been determined that as a result of magnetic measurements; the optimum value of applied outer magnetic field is 0.5T.

  5. Groundwater prospecting for sandstone-type uranium deposits: the merits of mineral-solution equilibria versus single element tracer methods. Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Wanty, R.B.; Langmuir, D.; Chatham, J.R.

    1981-08-01

    This report presents the results of further research on the groundwater geochemistry of 96 well waters in two uraniferous aquifers in Texas and Wyoming, and is a continuation of the work presented by Chatham et al. (1981). In this study variations in concentrations of U, As, Mo, Se and V were compared with the saturation state of the groundwater with respect to mineral phases of these elements known or expected to occur in each area. The non-radiogenic trace elements exhibited strong redox dependence consistent with thermodynamic predictions, but their variations did not pinpoint existing uranium ore bodies, because of a shift in groundwater flow patterns since the time of ore emplacement. Saturation levels of trace element minerals such as realgar, native Se, and molybdenite showed broad anomalies around the ore-bearing areas, similar to patterns found for U minerals by Langmuir and Chatham (1980), and Chatham et al. (1981). The radiogenic elements Ra and Rn showed significant anomalies directly within the ore zones. Helium anomalies were displaced in the direction of groundwater flow, but by their magnitude and areal extent provided strong evidence for the existence of nearby uranium accumulations. Uranium isotope ratios showed no systematic variations within the two aquifers studied. Saturation maps for kaolinite, illite, montmorillonite and the zeolites analcime and clinoptilolite provided 1 to 2 km anomalies around the ore at the Texas site. Saturation values for the gangue minerals pyrite and calcite defined the redox interface and often suggested the position of probable uranium mineralization. When properly used, the groundwater geochemical concepts for exploration can accurately pinpoint uranium mineralization at a fraction of the cost of conventional methods that involve test drilling and geophysical and core logging.

  6. Groundwater prospecting for sandstone-type uranium deposits: the merits of mineral-solution equilibria versus single element tracer methods. Volume II

    International Nuclear Information System (INIS)

    Wanty, R.B.; Langmuir, D.; Chatham, J.R.

    1981-08-01

    This report presents the results of further research on the groundwater geochemistry of 96 well waters in two uraniferous aquifers in Texas and Wyoming, and is a continuation of the work presented by Chatham et al. (1981). In this study variations in concentrations of U, As, Mo, Se and V were compared with the saturation state of the groundwater with respect to mineral phases of these elements known or expected to occur in each area. The non-radiogenic trace elements exhibited strong redox dependence consistent with thermodynamic predictions, but their variations did not pinpoint existing uranium ore bodies, because of a shift in groundwater flow patterns since the time of ore emplacement. Saturation levels of trace element minerals such as realgar, native Se, and molybdenite showed broad anomalies around the ore-bearing areas, similar to patterns found for U minerals by Langmuir and Chatham (1980), and Chatham et al. (1981). The radiogenic elements Ra and Rn showed significant anomalies directly within the ore zones. Helium anomalies were displaced in the direction of groundwater flow, but by their magnitude and areal extent provided strong evidence for the existence of nearby uranium accumulations. Uranium isotope ratios showed no systematic variations within the two aquifers studied. Saturation maps for kaolinite, illite, montmorillonite and the zeolites analcime and clinoptilolite provided 1 to 2 km anomalies around the ore at the Texas site. Saturation values for the gangue minerals pyrite and calcite defined the redox interface and often suggested the position of probable uranium mineralization. When properly used, the groundwater geochemical concepts for exploration can accurately pinpoint uranium mineralization at a fraction of the cost of conventional methods that involve test drilling and geophysical and core logging

  7. Comparison of inorganic ion exchange materials for removing cesium, strontium, and transuranic elements from K-basin water

    International Nuclear Information System (INIS)

    Brown, G.N.; Bontha, J.R.; Carson, K.J.; Elovich, R.J.; DesChane, J.R.

    1997-10-01

    The work presented in this report was conducted by the Pacific Northwest National Laboratory (PNNL) under the Efficient Separations and Crosscutting Program (ESP), Office of Science and Technology, U.S. Department of Energy (DOE). The objective of this work was to investigate radionuclide uptake by several newly produced ion exchange materials under actual waste conditions, and to compare the performance of those materials with that of commercially available ion exchangers. The equilibrium uptake data presented in this report are useful for identifying potential materials that are capable of removing cesium and strontium from 105-KE Basin water. The data show the relative selectivities of the ion exchange materials under similar operating conditions. Additional flow studies are needed to predict material capacities and to develop complete ion exchange process flow sheets. The materials investigated in this study include commercially available ion exchangers such as IONSIV reg-sign IE-911 (manufactured by UOP), clinoptilolite (a naturally occurring zeolite), and materials produced on an experimental basis by AlliedSignal (biotites and nonatitanates), 3M (hexacyanoferrates), Selion Technologies, Inc. (hexacyanoferrates and titanates), and Texas A ampersand M University (pharmacosiderites, biotites, and nonatitanates). In all, the performance of 14 ion exchange materials was evaluated at two solution-to-exchanger mass ratios (i.e., 10 4 and 10 5 ) using actual 105-KE Basin water. Evaluation consisted of determining cesium and strontium batch distribution coefficients, loading, and decontamination factors. Actual 105-KE Basin water was obtained from a sample collected during the sludge dissolution work conducted by PNNL in FY 1996. This sample was taken from the bottom of the basin and contained significantly higher concentrations of the radioactive constituents than do samples taken from the top of the basin

  8. Determination of mineral abundances in samples from the exploratory studies facility using x-ray diffraction

    International Nuclear Information System (INIS)

    Roberts, S.; Viani, R.

    1998-01-01

    Tuff samples collected from the Exploratory Studies Facility (ESF) were X-rayed to estimate relative mineral abundances. X-ray analysis was performed on sub-samples of specimens collected from both the Single Heater Test (SHT) and Drift Scale Heater Test (DST) that were used for thermomechanical measurements, as well as samples collected from cores retrieved from boreholes in the Drift Scale Test Area. The abundance of minerals that could affect the behavior of the host rock at repository relevant temperatures is of particular interest. These minerals include crystobalite, which undergoes a phase transition and volume change at elevated temperature (-250 'C), and smectite and clinoptilolite that can dehydrate at elevated temperature with accompanying volume reduction. In addition, the spatial distribution of SiO, polymorphs and secondary minerals may provide evidence for deducing past fluid pathways. The mineral abundances tabulated here include data reported previously in three milestone reports (Roberts and Viani, 1997a,b; Viani and Roberts, 1996) but re-analyzed (see below), as well as previously unreported data. Previous X-ray diffraction analyses of samples from the ESF (Roberts and Viani, 1997a; Viani and Roberts, 1996) utilized the matrix flushing method of Chung (1974) and an internal intensity standard (corundum) to quantify the abundances of the phases present. Although the method is adequate for obtaining relative abundances, its accuracy and precision is limited by the inherent differences between the external standards used to compute the reference intensity ratio and the mineral phases in the sample. In a subsequent report (Roberts and Viani, 1997b) mineral abundances were obtained using the Rietveld method of whole X-ray pattern fitting (Snyder and Bish, 1989; Young, 1993). The Rietveld technique has the potential to be both more accurate and more precise for estimating mineral abundances (Snyder and Bish, 1989)

  9. Selectivity of the adsorption process of modified zeolite rock with hexadecyl trimethylammonium bromide in front to chromates and dichromates; Selectividad del proceso de adsorcion de roca zeolitica modificada con bromuro de hexadeciltrimetilamonio frente a cromatos y dicromatos

    Energy Technology Data Exchange (ETDEWEB)

    Salgado G, N.

    2011-07-01

    In the present investigation natural zeolite (clinoptilolite) from the Chihuahua state, which was conditioned with sodium chloride solution and subsequently modified with a hexadecyl trimethylammonium bromide solution was used to evaluate the removal of Cr (Vi) from chromate or dichromate solutions. The zeolite materials were characterized by scanning electron microscopy and X-ray diffraction. The surface area was also determined. The experiments were performed in a batch system, the influence of ph, contact time between phases were investigated and during the adsorption process was calculated the concentration of chromium ion present in aqueous solution (CrO{sub 4}{sup 2-}, Cr{sub 2}O{sub 7}{sup 2-}). The quantification of chromium removed from the aqueous solution by atomic absorption spectrometry technique was done. In order to understand the behaviour of the adsorption kinetics the pseudo first and pseudo second order models were applied, and to determine the adsorption capacity of the zeolite materials for Cr the Langmuir, Freundlich and Langmuir-Freundlich models were chosen. It was found that the removal efficiency of chromium ion is influenced by ph and the chemical species present: chromate or dichromate. The chromate and dichromate sorption kinetic data were best fitted to the pseudo-second and pseudo-first order models, respectively; and the Langmuir and Langmuir-Freundlich models described adequately the isotherms data considering a mono component system. In a mixture of Cr (Vi) ad CrO{sub 4}{sup 2-} and Cr{sub 2}O{sub 7}{sup 2-}, the surfactant modified zeolite has a greater selectivity for Cr{sub 2}O{sub 7}{sup 2-} ion than CrO{sub 4}{sup 2-}. In this case the Langmuir-Freundlich model described the adsorption isotherm behavior. (Author)

  10. The Occurrence of Erionite at Yucca Mountain

    International Nuclear Information System (INIS)

    NA

    2004-01-01

    The naturally-occurring zeolite mineral erionite has a fibrous morphology and is a known human carcinogen (inhalation hazard). Erionite has been found typically in very small quantities and restricted occurrences in the course of mineralogic characterization of Yucca Mountain as a host for a high-level nuclear waste repository. The first identification of erionite was made in 1984 on the basis of morphology and chemical composition and later confirmed by X-ray diffraction analysis. It was found in the lower vitrophyre (Tptpv3) of the Topopah Spring Tuff in a borehole sidewall sample. Most erionite occurrences identified at Yucca Mountain are in the Topopah Spring Tuff, within an irregular zone of transition between the lower boundary of devitrified tuff and underlying glassy tuff. This zone is fractured and contains intermingled devitrified and vitric tuff. In 1997, a second host of erionite mineralization was identified in the Exploratory Studies Facility within and adjacent to a high-angle fracture/breccia zone transgressing the boundary between the lowermost devitrified tuff (Tpcplnc) and underlying moderately welded vitric tuff (Tpcpv2) of the Tiva Canyon Tuff. The devitrified-vitric transition zones where erionite is found tend to have complex secondary-mineral assemblages, some of very localized occurrence. Secondary minerals in addition to erionite may include smectite, heulandite-clinoptilolite, chabazite, opal-A, opal-CT, cristobalite, quartz, kenyaite, and moganite. Incipient devitrification within the Topopah Spring Tuff transition zone includes patches that are highly enriched in potassium feldspar relative to the precursor volcanic glass. Geochemical conditions during glass alteration may have led to local evolution of potassium-rich fluids. Thermodynamic modeling of zeolite stability shows that erionite and chabazite stability fields occur only at aqueous K concentrations much higher than in present Yucca Mountain waters. The association of erionite

  11. Immobilization of Co{sup 2+} and Cs{sup +} in zeolites by thermal treatment and by combustion; Inmovilizacion de Co{sup 2+} y Cs{sup +} en zeolitas por tratamiento termico y por combustion

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez T, R.; Bulbulian G, S. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: rosarodtre@yahoo.com

    2005-07-01

    The radioactive waste, either those that take place in the {sup 235}U fission or those that are used in the radiochemical laboratories, are dangerous for the human being and for the one environment. The liquid radioactive wastes are of those that present bigger problem. It has intended to retain by the ion exchange method the radioactive ions of the liquids using, for example, zeolites. In this work so much synthetic zeolites was used (A and X) like a natural zeolite (clinoptilolite). Its were put in contact with cobalt or cesium solutions to simulate radioactive solutions. A part of the zeolite cations were exchanged with cobalt or cesium cations, eliminating them by this way of the solution. However, in extreme conditions these cations can be leached of the solids. To immobilize the cobalt or cesium cations in the zeolites net its are usually carried out thermal treatments to such temperatures that the structure is destroyed and that the contaminating ions are trapped in a solid often vitreous. The exchanged zeolites with cobalt or cesium, on one hand, its were thermally treated to different temperatures during three hours and by the other one, according to the treatment method by combustion, to different temperatures during five minutes in presence of urea, later its were put in contact with a solution of NaCl to measure the leaching of the interest cations. These solutions were analyzed by neutron activation. In general it was found that as the treatment temperature increases (in both methods) the so much immobility of the cesium like of the cobalt it increases. The grade of crystallinity of the samples before and after the treatments it was determined by X-ray diffraction. (Author)

  12. Development of Stable Solidification Method for Insoluble Ferrocyanides-13170

    Energy Technology Data Exchange (ETDEWEB)

    Ikarashi, Yuki; Masud, Rana Syed; Mimura, Hitoshi [Dept. of Quantum Science and Energy Engineering, Graduate School of Engineering, Tohoku University, Aramaki-Aza-Aoba6-6-01-2, Sendai, 980-8579 (Japan); Ishizaki, Eiji; Matsukura, Minoru [UNION SHOWA K.K. 17-20, Mita 2-chome, Minato-ku, Tokyo 108-0073 (Japan)

    2013-07-01

    The development of stable solidification method of insoluble ferrocyanides sludge is an important subject for the safety decontamination in Fukushima NPP-1. By using the excellent immobilizing properties of zeolites such as gas trapping ability and self-sintering properties, the stable solidification of insoluble ferrocyanides was accomplished. The immobilization ratio of Cs for K{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O saturated with Cs{sup +} ions (Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O) was estimated to be less than 0.1% above 1,000 deg. C; the adsorbed Cs{sup +} ions are completely volatilized. In contrast, the novel stable solid form was produced by the press-sintering of the mixture of Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O and zeolites at higher temperature of 1,000 deg. C and 1,100 deg. C; Cs volatilization and cyanide release were completely depressed. The immobilization ratio of Cs, under the mixing conditions of Cs{sub 2}[CoFe(CN){sub 6}].nH{sub 2}O:CP= 1:1 and calcining temperature: 1,000 deg. C, was estimated to be nearly 100%. As for the kinds of zeolites, natural mordenite (NM), clinoptilolite (CP) and Chabazite tended to have higher immobilization ratio compared to zeolite A. This may be due to the difference in the phase transformation between natural zeolites and synthetic zeolite A. In the case of the composites (K{sub 2-X}Ni{sub X/2}[NiFe(CN){sub 6}].nH{sub 2}O loaded natural mordenite), relatively high immobilization ratio of Cs was also obtained. This method using zeolite matrices can be applied to the stable solidification of the solid wastes of insoluble ferrocyanides sludge. (authors)

  13. Further description of the petrology of the Topopah Spring member of the paintbrush tuff in drill holes UE25A-1 and USW-G1 and of the lithic-rich tuff in USW-G1, Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Carroll, P.I.; Caporuscio, F.A.; Bish, D.L.

    1981-11-01

    The Topopah Spring Member of the Paintbrush Tuff and the Lithic-rich tuff and two Tertiary volcanic units that occur in cores from drill holes UE25a-1 and USW-G1 at Yucca Mountain, Nevada. Recently they have been suggested as possibly suitable for the permanent storage of high-level radioactive waste. Earlier petrologic characterization of these units is augmented here. The Topopah Spring Member (approximately 350 m thick) has two compound cooling units. The upper, thinner unit is densely welded to vitrophyric. The lower unit ranges from nonwelded to vitrophyric, and its nonwelded base is extensively zeolitized to clinoptilolite and mordenite. Heulandite occurs as fracture fill in the overlying vitrophyric part, but zeolites are absent above that vitrophyre. Here primary devitrification plus vapor-phase crystallization dominate the mineralogy. Vapor-phase effects are especially prominent between the two vitrophyres in both cores and include numerous large lithophysal cavities throughout most of this moderately to densely welded tuff. The Lithic-rich tuff extends from 1203 to 1506 m in the USW-G1 drill core. It is nonwelded to partly welded but is well indurated due to pervasive intergrowths of authigenic minerals. These phases are analcime, albite, alkali feldspar, sericite, chlorite and quartz. The transition from analcime to secondary albite corresponds to Iijima's zeolite Zone IV boundary, and this boundary appears in USW-G1 at 1326 m. However, analcime remains as a prominent phase through most of the Lithic-rich tuff. Further work is necessary to assess the suitability of either of these horizons for a waste repository. In the Topopah Spring Member, both mechanical and hydrologic properties of thick lithophysal zone must be studied, as well as the complete sequence of fracture fill. For both units, zeolite and clay mineral stabilities need to be investigated

  14. A comprehensive study on photocatalytic activity of supported Ni/Pb sulfide and oxide systems onto natural zeolite nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Babaahamdi-Milani, Majid [Department of Chemistry, Shahreza Branch, Islamic Azad University, P.O. Box 311-86145, Shahreza, Isfahan (Iran, Islamic Republic of); Young Researchers and Elite Club, Shahreza Branch, Islamic Azad University, Shahreza (Iran, Islamic Republic of); Nezamzadeh-Ejhieh, Alireza, E-mail: arnezamzadeh@iaush.ac.ir [Department of Chemistry, Shahreza Branch, Islamic Azad University, P.O. Box 311-86145, Shahreza, Isfahan (Iran, Islamic Republic of); Young Researchers and Elite Club, Shahreza Branch, Islamic Azad University, Shahreza (Iran, Islamic Republic of); Razi Chemistry Research Center (RCRC), Shahreza Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of)

    2016-11-15

    Highlights: • Increase in photocatalytic activity of hybridized/supported PbO/NiO and PbS/NiS systems with respect to semiconductors alone. • Higher efficiency of PbO/NiO than PbS/NiS. • Positive role of p-n junction for enhancement of photocatalytic activity of the used semiconductors. - Abstract: The Ni(II)-Pb(II) exchanged clinoptilolite nanoparticles (NCP) were transformed to corresponding oxides and sulfides via calcination and sulfiding processes, respectively. The obtained catalysts were characterized by XRD, FT-IR, TEM and DRS and used in photodegradation of p-nitrophenol (4-NP) aqueous solution under Hg-lamp irradiation. Results showed considerable increase in activity of the coupled semiconductors with respect to monocomponent one. In NiO-PbO-NCP system, conduction band (CB) of NiO is enough negative for easily migration of photogenerated electrons to CB-PbO level, while such phenomena take place from more negative CB-PbS level to CB-NiS level in NiS-PbS-NCP. These phenomena significantly prevented from electron-hole recombination which increased photocatalytic activity of the coupled semiconductors. Best photodegradation activities obtained by NiO{sub 1.3%}–PbO{sub 14.7%}-NCP and NiS{sub 2.1%}–PbS{sub 10.0%}-NCP, confirming semiconductors' mass-ratio dependence of the photocatalytic process. The supported coupled semiconductors showed blue shifts in band gap energies with respect to the bulk semiconductors which confirm formation of semiconductors nanoparticles inside the zeolite framework. The highest degradation percentage of 4-NP was obtained at: 0.5 g L{sup −1} photocatalysts, 15 mg L{sup −1} 4-NP at pH 7.5.

  15. Comparison of inorganic ion exchange materials for removing cesium, strontium, and transuranic elements from K-basin water

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.N.; Bontha, J.R.; Carson, K.J.; Elovich, R.J.; DesChane, J.R.

    1997-10-01

    The work presented in this report was conducted by the Pacific Northwest National Laboratory (PNNL) under the Efficient Separations and Crosscutting Program (ESP), Office of Science and Technology, U.S. Department of Energy (DOE). The objective of this work was to investigate radionuclide uptake by several newly produced ion exchange materials under actual waste conditions, and to compare the performance of those materials with that of commercially available ion exchangers. The equilibrium uptake data presented in this report are useful for identifying potential materials that are capable of removing cesium and strontium from 105-KE Basin water. The data show the relative selectivities of the ion exchange materials under similar operating conditions. Additional flow studies are needed to predict material capacities and to develop complete ion exchange process flow sheets. The materials investigated in this study include commercially available ion exchangers such as IONSIV{reg_sign} IE-911 (manufactured by UOP), clinoptilolite (a naturally occurring zeolite), and materials produced on an experimental basis by AlliedSignal (biotites and nonatitanates), 3M (hexacyanoferrates), Selion Technologies, Inc. (hexacyanoferrates and titanates), and Texas A&M University (pharmacosiderites, biotites, and nonatitanates). In all, the performance of 14 ion exchange materials was evaluated at two solution-to-exchanger mass ratios (i.e., 10{sup 4} and 10{sup 5}) using actual 105-KE Basin water. Evaluation consisted of determining cesium and strontium batch distribution coefficients, loading, and decontamination factors. Actual 105-KE Basin water was obtained from a sample collected during the sludge dissolution work conducted by PNNL in FY 1996. This sample was taken from the bottom of the basin and contained significantly higher concentrations of the radioactive constituents than do samples taken from the top of the basin.

  16. Copper removal using bio-inspired polydopamine coated natural zeolites

    International Nuclear Information System (INIS)

    Yu, Yang; Shapter, Joseph G.; Popelka-Filcoff, Rachel; Bennett, John W.; Ellis, Amanda V.

    2014-01-01

    Highlights: • Natural zeolites were modified with bio-inspired polydopamine. • A 91.4% increase in Cu(II) ion adsorption capacity was observed. • Atomic absorption and neutron activation analysis gave corroborative results. • Neutron activation analysis was used to provide accurate information on 30+ elements. • Approximately 90% of the adsorbed copper could be recovered by 0.1 M HCl treatment. - Abstract: Herein, for the first time, natural clinoptilolite-rich zeolite powders modified with a bio-inspired adhesive, polydopamine (PDA), have been systematically studied as an adsorbent for copper cations (Cu(II)) from aqueous solution. Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and thermogravimetric analysis (TGA) revealed successful grafting of PDA onto the zeolite surface. The effects of pH (2–5.5), PDA treatment time (3–24 h), contact time (0 to 24 h) and initial Cu(II) ion concentrations (1 to 500 mg dm −3 ) on the adsorption of Cu(II) ions were studied using atomic absorption spectroscopy (AAS) and neutron activation analysis (NAA). The adsorption behavior was fitted to a Langmuir isotherm and shown to follow a pseudo-second-order reaction model. The maximum adsorption capacities of Cu(II) were shown to be 14.93 mg g −1 for pristine natural zeolite and 28.58 mg g −1 for PDA treated zeolite powders. This impressive 91.4% increase in Cu(II) ion adsorption capacity is attributed to the chelating ability of the PDA on the zeolite surface. Furthermore studies of recyclability using NAA showed that over 50% of the adsorbed copper could be removed in mild concentrations (0.01 M or 0.1 M) of either acid or base

  17. Comparing Two Operating Configurations in a Full-Scale Arsenic Removal Plant. Case Study: Guatemala

    Directory of Open Access Journals (Sweden)

    Sofía E. Garrido Hoyos

    2013-06-01

    Full Text Available The present study was conducted in Naranjo County located in the municipality of Mixco, Guatemala. The water supply source comes from two wells with a maximum flow of 25.24 and 33.44 L·s−1. The main problem with this source is the high arsenic concentration—between 0.1341 and 0.1671 mg·L−1. The aim of this study was to conduct laboratory tests, basic engineering and supervision of the construction and evaluation of an operations plant using two configurations, A (low-rate sedimentation and ceramic filter and B (high-rate sedimentation and clinoptilolite filter, to remove arsenic present in water for human use and consumption. This plant supplies water to Naranjo County in Mixco, Guatemala (5000 inhabitants. First, a laboratory Jar Test was performed to evaluate arsenic removal efficiency. And second, a conventional clarification plant was then built (design flow: 25.24 L·s−1. The best results were achieved with configuration B, with the following reagents and dosage as defined by the laboratory tests: 10 mg L−1 ferric chloride as coagulant; 1.8 mg·L−1 CH-polyfocal as flocculant and 0.4 mg L−1 MIT03 as color removal; 1 mg L−1 sodium hypochlorite as oxidant and adjusting pH to ≈7.0 with sodium hydroxide. Once the plant began operating, the efficiency of the treatment process was evaluated. The maximum elimination efficiencies were obtained 100% for turbidity (0 UTN, 89.54% (3.66 UPt-Co for color and 96.80% (0.005 mg L−1 for arsenic, values that comply with Guatemalan standards. For this case, the relation between Fe(III dosage/mg and As(V removal was 1:46.

  18. Minerals in fractures of the saturated zone from drill core USW G-4, Yucca Mountain, Nye County, Nevada

    International Nuclear Information System (INIS)

    Carlos, B.A.

    1987-04-01

    The minerals in fractures in drill core USW G-4, from the static water level (SWL) at 1770 ft to the base of the hole at 3000 ft, were studied to determine their identity and depositional sequence and to compare them with those found above the SWL in the same drill hole. There is no change in mineralogy or mineral morphology across the SWL. The significant change in mineralogy and relationship to the host rock occurs at 1381 ft, well above the present water table. Below 1381 ft clinoptilolite appears in the fractures and rock matrix instead of heulandite, and the fracture mineralogy correlates with the host rock mineralogy. Throughout most of the saturated zone (below the SWL) in USW G-4, zeolites occur in fractures only in zeolitic tuff; however, zeolites persist in fracture below the base of the deepest zeolitic tuff interval. Nonzeolitic intervals of tuff have fewer fractures, and many of these have no coatings; a few have quartz and feldspar coatings. One interval in zeolitic tuff (2125-2140 ft) contains abundant crisobalite coatings in the fractures. Calcite occurs in fractures from 2575 to 2660 ft, usually with the manganese mineral hollandite, and from 2750 to 2765 ft, usually alone. Manganese minerals occur in several intervals. The spatial correlation of zeolites in fractures with zeolitic host rock suggests that both may have been zeolitized at the same time, possibly by water moving laterally through more permeable zones in the tuff. The continuation of zeolites in fractures below the lowest zeolitic interval in this hole suggests that vertical fracture flow may have been important in the deposition of these coatings. Core from deeper intervals in another hole will be examined to determine if that relationship continues. 17 refs., 19 figs

  19. Dissolution kinetics of heulandite at pH 2--12 and 25 degrees C

    International Nuclear Information System (INIS)

    Ragnarsdottir, K.V.

    1993-01-01

    Because of their favourable cation exchange reactions, heulandite and clinoptilolite have been suggested as being capable of immobilizing radionuclides and therefore could possibly act as an important barrier for nuclear waste. Recent studies of laboratory-reacted minerals indicate, however, that hydrated surface layers tend to accumulate highly hydrolyzable heavy elements. These hydrated layers may therefore be the most important retardants for radionuclides. The dissolution rate of heulandite depends strongly on pH. Based on silica release, the logarithm of the steady-state dissolution rate at pH 2 is -13.1 mol cm -2 s -1 . The logarithm of the rate decreases to -15.8 mol cm -2 s -1 at pH 7.2 and increases again to -14.6 mol cm -2 s -1 at pH 12.2. At low pH, Al is released preferentially to silica; but at intermediate and high pH, the release of silica appears to be congruent relative to Al. The change in dissolution rate with pH indicates that at low pH, the dissolution mechanism is controlled by the detachment of a positively charged Al species, >Al-OH 2 + . Below pH 5, however, a silica-rich surface layer is formed requiring diffusion through the layer. At intermediate and high pH, it is likely that the dissolution rate is controlled by the detachment of a negatively charged silica species, >Si - O - . The reaction order of the hydrogen ion under low pH conditions is 0.7, and the reaction order of the OH - ion is 0.3 at high pH. The measured dissolution rates indicate that a 1 mm heulandite crystal would dissolve in 300,000 yrs if the solution composition is maintained undersaturated. 75 refs., 11 figs., 3 tabs

  20. Adsorption of aqueous Zn(II) species on synthetic zeolites

    International Nuclear Information System (INIS)

    Badillo-Almaraz, Veronica; Trocellier, Patrick; Davila-Rangel, Ignacio

    2003-01-01

    To supply a good quality drinkable water tends to become a strategic task in both developed and under development countries in the world due to the number of potential contamination sources. One of the major problems is derived from the presence of heavy toxic metals like zinc or lead resulting from industrial activities. Zeolites are known as very efficient mineral substrates for fixing aqueous ionic species through their wide range of channels present in the crystalline structure and due to their strong surface reactivity. MicroPIXE coupled with microRBS (3.05 MeV 4 He + ions) have been used to quantify the incorporation of zinc within two commercial zeolites containing alkali elements (zeolite X and clinoptilolite) in the concentration range of: 0.0002-0.05 M at neutral pH. At the beginning of the interaction between zeolite and Zn(II) solution, the adsorption process exhibits a direct proportionality between the content of zinc fixed on the mineral substrate and the aqueous concentration up to 0.01 M. Beyond this point a saturation effect seems to occur, indicating the strong decrease of available adsorption sites. Sodium or potassium ions are probably exchanged with Zn(II) ions during this process. The compared behaviour of the two zeolites is then discussed in terms of kinetic effects based on ionic radius values. A co-adsorption test carried on with a 50-50% Zn(II) 0.001 M-Pb(II) 0.001 M solution shows that lead does not occupy the same sites as zinc because the content of zinc fixed on the zeolite sample exactly corresponds to the result obtained with a pure 0.001 M Zn(II) solution. All these data clearly showed that zeolite surface reactivity is greatly influenced by the mineral cage-like structure and particularly the presence of pockets, spaces and channels

  1. Immobilization of Co2+ and Cs+ in zeolites by thermal treatment and by combustion

    International Nuclear Information System (INIS)

    Rodriguez T, R.; Bulbulian G, S.

    2005-01-01

    The radioactive waste, either those that take place in the 235 U fission or those that are used in the radiochemical laboratories, are dangerous for the human being and for the one environment. The liquid radioactive wastes are of those that present bigger problem. It has intended to retain by the ion exchange method the radioactive ions of the liquids using, for example, zeolites. In this work so much synthetic zeolites was used (A and X) like a natural zeolite (clinoptilolite). Its were put in contact with cobalt or cesium solutions to simulate radioactive solutions. A part of the zeolite cations were exchanged with cobalt or cesium cations, eliminating them by this way of the solution. However, in extreme conditions these cations can be leached of the solids. To immobilize the cobalt or cesium cations in the zeolites net its are usually carried out thermal treatments to such temperatures that the structure is destroyed and that the contaminating ions are trapped in a solid often vitreous. The exchanged zeolites with cobalt or cesium, on one hand, its were thermally treated to different temperatures during three hours and by the other one, according to the treatment method by combustion, to different temperatures during five minutes in presence of urea, later its were put in contact with a solution of NaCl to measure the leaching of the interest cations. These solutions were analyzed by neutron activation. In general it was found that as the treatment temperature increases (in both methods) the so much immobility of the cesium like of the cobalt it increases. The grade of crystallinity of the samples before and after the treatments it was determined by X-ray diffraction. (Author)

  2. Influence of contamination indicative components of the residual water coming from a treatment plant of Toluca Valley on the microbial activity of conditioned clinoptilolite with silver against E. Coli

    International Nuclear Information System (INIS)

    Rossainz C, L. G.

    2013-01-01

    In the present study we used zeolite from the state of Chihuahua which was subjected to a conditioning process with silver to verify the effect as microbicidal agent against Escherichia coli in the presence of different ions (NO 3 - , NO 2 - , SO 4 2- , Cl - , Fe 2+ and Mg 2+ ), found in the effluent of a Valle de Toluca treatment plant. The zeolite material was conditioned with a solution of sodium chloride and then with a solution of silver nitrate and was characterized by scanning electron microscopy and X-ray diffraction. Ion concentration was determined in the treatment plant effluent by standards methods specific, for each ion. A solution containing E. coli cells in batch type process was used to investigate four important aspects: a) the bactericidal effect that presents the zeolitic material conditioned against E. coli, b) the influence of ions NO 3 - , NO 2 - , SO 4 2- , Cl - , Fe 2+ and Mg 2+ on the bactericidal effect of the conditioned zeolitic material, c) the effect of the ions NO 3 - , NO 2 - , SO 4 2- , Cl - , Fe 2+ and Mg 2+ for the desorption of silver ions from the conditioned zeolite material and d) the kinetics of disinfection processes. The amount of bacteria was determined using APHA method and silver contained in water was determined by atomic absorption spectroscopy. The Chick model was considered to describe the kinetic behavior of the disinfection process. According with the results was found, that the conditioned zeolite silver from the state of Chihuahua is useful bactericide agent for water disinfection and that the desorbed amount of silver as well as the chemical species present in water at the time of disinfection process are factors that influence the process efficiency. (Author)

  3. Adsorption of nicotine on different zeolite types, from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Stošić Dušan K.

    2007-01-01

    Full Text Available The plant alkaloid, nicotine, is a strongly toxic heterocyclic compound: the lethal dose for an adult human being (40-60 mg is importantly lower in comparison with the other known poisons such as arsenic or strychni­ne. Cigarettes represent "the most toxic and addictive form of nicotine". Besides the negative effects of nicotine on public health produced by self-administration, recently another potentially very dangerous effect has been recognized: because of its miscibility with water, nicotine can be found in industrial wastewaters, and consequently, in groundwater. Therefore, the problem of nicotine removal from aqueous solutions has became an interesting topic. In this work, the removal of nicotine has been probed by adsorption on solid materials. Adsorption of nicotine on different zeolites (clinoptilolite, ZSM-5 and β zeolite and on activated carbon was investigated from aqueous solutions, at 298 K. The obtained results are presented as adsorption isotherms: the amount of adsorbed nicotine as a function of equilibrium concentration. These data were obtained from the residual amount of nicotine in the aqueous phase, by the use of UV spectroscopy. The highest amounts of adsorbed nicotine was found for activated carbon and p zeolite (~ mmol·g-1. The attempt to modify the adsorption properties of ZSM-5 zeolite has been also done: ZSM-5 was modified by ion-exchange with VIII group metal (Cu2+ and Fe3+. In addition, the adsorption of nicotine on ZSM-5 zeolite with different Si/Al ratios has been done. It has been noticed that ion-exchange did not improve the adsorption possibilities, while the adsorption was importantly lower in the case of higher silicon content in ZMS-5 structure. 13C NMR spectra were collected for suspensions formed of solid adsorbent and aqueous solution of nicotine; in this way, the part of nicotine molecule which is most probably connected with the adsorbent was recognized.

  4. Stratigraphy, structure, and some petrographic features of Tertiary volcanic rocks at the USW G-2 drill hole, Yucca Mountain, Nye County, Nevada

    International Nuclear Information System (INIS)

    Maldonado, F.; Koether, S.L.

    1983-01-01

    A continuously cored drill hole penetrated 1830.6 m of Tertiary volcanic strata comprised of the following in descending order: Paintbrush Tuff, tuffaceous beds of Calico Hills, Crater Flat Tuff, lava and flow breccia (rhyodacitic), tuff of Lithic Ridge, bedded and ash-flow tuff, lava and flow breccia bedded tuff, conglomerate and ash-flow tuff, and older tuffs of USW G-2. Comparison of unit thicknesses at USW G-2 to unit thicknesses at previously drilled holes at Yucca Mountain indicate: (1) thickening of the Paintbrush Tuff members and tuffaceous beds of Calico Hills toward the northern part of Yucca Mountain; (2) thickening of the Prow Pass Member but thinning of the Bullfrog Member and Tram unit; (3) thinning of the tuff of Lithic Ridge; (4) presence of about 280 m of lava and flow breccia not previously penetrated by any drill hole; and (5) presence of an ash-flow tuff unit at the bottom of the drill hole not previously intersected, apparently the oldest unit penetrated at Yucca Mountain to date. Petrographic features of some of the units include: (1) decrease in quartz and K-feldspar and increases in biotite and plagioclase with depth in the tuffaceous beds of Calico Hills; (2) an increase in quartz phenocrysts from the top to the bottom members of the Crater Flat Tuff; (3) a low quartz content in the tuff of Lithic Ridge, suggesting tapping of the magma chamber at quartz-poor levels; (4) a change in zeolitic alteration from heulandite to clinoptilolite to mordenite with increasing depth; (5) lavas characterized by a rhyolitic top and dacitic base, suggesting reverse compositional zoning; and (6) presence of hydrothermal mineralization in the lavas that could be related to an itrusive under Yucca Mountain or to volcanism associated with the Timber Mountain-Claim Canyon caldera complex. A fracture analysis of the core resulted in tabulation of 7848 fractures, predominately open and high angle

  5. Stabilization of metals in acidic mine spoil with amendments and red fescue (Festuca rubra L.) growth.

    Science.gov (United States)

    Simon, László

    2005-12-01

    Stabilization of metals with amendments and red fescue (Festuca rubra, cv. Keszthelyi 2) growth was studied on an acidic and phytotoxic mine spoil (pH(KCl) 3.20-3.26; Cd 7.1 mg kg(-1), Cu 120 mg kg(-1), Pb 2154 mg kg(-1) and Zn 605 mg kg(-1)) from Gyöngyösoroszi, Hungary in a pot experiment. Raising the pH above 5.0 by lime (CaCO(3)), and supplementing with 40 mg kg(-1)nitrogen (NH(4)NO(3)) made this material suitable for plant growth. All cultures were limed with 0.5% (m/m) CaCO(3) (treatment 1), which was combined with 5% (m/m) municipal sewage sludge compost (treatment 2), 5% (m/m) peat (treatment 3), 7.5% (m/m) natural zeolite (clinoptilolite) (treatment 4), and 0.5 (m/m) KH(2)PO(4) (treatment 5). Treatments 1-5 were combined with each other (treatment 6). After 60 days of red fescue growth, pH of the limed mine spoil decreased in all cultures units. Application of peat caused the highest pH decrease (1.15), while decrease of pH was less than 0.23 in treatments 2, 5 or 6. Application of lime significantly reduced concentrations of metals in the 'plant available' fraction of mine spoil compared to non-limed mine spoil. Amendments added to limed mine spoil changed variously the ratio of Cd, Cu, Pb and Zn in exchangeable or 'plant available' fractions, differently influencing the phytoavailability of these metals. Most of the metals were captured in the roots of test plants. Treatment 2 caused the appearance of less Cd in shoots (spoil, however the application of 0.5 phosphate was less favourable. Liming, application of amendments and growth of red fescue can stabilize metals in acidic and phytotoxic mine spoil, and by phytostabilization they can reduce the risk of metal contamination of the food chain.

  6. Hyperspectral image analysis for the determination of alteration minerals in geothermal fields: Çürüksu (Denizli) Graben, Turkey

    Science.gov (United States)

    Uygur, Merve; Karaman, Muhittin; Kumral, Mustafa

    2016-04-01

    infrared seen in geothermal fields. Hyperspectral analysis results indicated that kaolinite, smectite, illite, montmorillonite, and sepiolite minerals were distributed in a wide area, which covered the hot spring outlet. Rectorite, lizardite, richterite, dumortierite, nontronite, erionite, and clinoptilolite were observed occasionally.

  7. Long-term product consistency test of simulated 90-19/Nd HLW glass

    International Nuclear Information System (INIS)

    Gan, X.Y.; Zhang, Z.T.; Yuan, W.Y.; Wang, L.; Bai, Y.; Ma, H.

    2011-01-01

    Chemical durability of 90-19/Nd glass, a simulated high-level waste (HLW) glass in contact with the groundwater was investigated with a long-term product consistency test (PCT). Generally, it is difficult to observe the long term property of HLW glass due to the slow corrosion rate in a mild condition. In order to overcome this problem, increased contacting surface (S/V = 6000 m -1 ) and elevated temperature (150 o C) were employed to accelerate the glass corrosion evolution. The micro-morphological characteristics of the glass surface and the secondary minerals formed after the glass alteration were analyzed by SEM-EDS and XRD, and concentrations of elements in the leaching solution were determined by ICP-AES. In our experiments, two types of minerals, which have great impact on glass dissolution, were found to form on 90-19/Nd HLW glass surface when it was subjected to a long-term leaching in the groundwater. One is Mg-Fe-rich phyllosilicates with honeycomb structure; the other is aluminosilicates (zeolites). Mg and Fe in the leaching solution participated in the formation of phyllosilicates. The main components of phyllosilicates in alteration products of 90-19/Nd HLW glass are nontronite (Na 0.3 Fe 2 Si 4 O 10 (OH) 2 .4H 2 O) and montmorillonite (Ca 0.2 (Al,Mg) 2 Si 4 O 10 (OH) 2 .4H 2 O), and those of aluminosilicates are mordenite ((Na 2 ,K 2 ,Ca)Al 2 Si 10 O 24 .7H 2 O)) and clinoptilolite ((Na,K,Ca) 5 Al 6 Si 30 O 72 .18H 2 O). Minerals like Ca(Mg)SO 4 and CaCO 3 with low solubility limits are prone to form precipitant on the glass surface. Appearance of the phyllosilicates and aluminosilicates result in the dissolution rate of 90-19/Nd HLW glass resumed, which is increased by several times over the stable rate. As further dissolution of the glass, both B and Na in the glass were found to leach out in borax form.

  8. Zeolite Combined with Alum and Polyaluminum Chloride Mixed with Agricultural Slurries Reduces Carbon Losses in Runoff from Grassed Soil Boxes.

    Science.gov (United States)

    Murnane, J G; Brennan, R B; Fenton, O; Healy, M G

    2016-11-01

    Carbon (C) losses from agricultural soils to surface waters can migrate through water treatment plants and result in the formation of disinfection by-products, which are potentially harmful to human health. This study aimed to quantify total organic carbon (TOC) and total inorganic C losses in runoff after application of dairy slurry, pig slurry, or milk house wash water (MWW) to land and to mitigate these losses through coamendment of the slurries with zeolite (2.36-3.35 mm clinoptilolite) and liquid polyaluminum chloride (PAC) (10% AlO) for dairy and pig slurries or liquid aluminum sulfate (alum) (8% AlO) for MWW. Four treatments under repeated 30-min simulated rainfall events (9.6 mm h) were examined in a laboratory study using grassed soil runoff boxes (0.225 m wide, 1 m long; 10% slope): control soil, unamended slurries, PAC-amended dairy and pig slurries (13.3 and 11.7 kg t, respectively), alum-amended MWW (3.2 kg t), combined zeolite and PAC-amended dairy (160 and 13.3 kg t zeolite and PAC, respectively) and pig slurries (158 and 11.7 kg t zeolite and PAC, respectively), and combined zeolite and alum-amended MWW (72 and 3.2 kg t zeolite and alum, respectively). The unamended and amended slurries were applied at net rates of 31, 34, and 50 t ha for pig and dairy slurries and MWW, respectively. Significant reductions of TOC in runoff compared with unamended slurries were measured for PAC-amended dairy and pig slurries (52 and 56%, respectively) but not for alum-amended MWW. Dual zeolite and alum-amended MWW significantly reduced TOC in runoff compared with alum amendment only. We conclude that use of PAC-amended dairy and pig slurries and dual zeolite and alum-amended MWW, although effective, may not be economically viable to reduce TOC losses from organic slurries given the relatively low amounts of TOC measured in runoff from unamended slurries compared with the amounts applied. Copyright © by the American Society of Agronomy, Crop Science Society of

  9. Geology of the Mid-Miocene Rooster Comb Caldera and Lake Owyhee Volcanic Field, eastern Oregon: Silicic volcanism associated with Grande Ronde flood basalt

    Science.gov (United States)

    Benson, Thomas R.; Mahood, Gail A.

    2016-01-01

    The Lake Owyhee Volcanic Field (LOVF) of eastern Oregon consists of rhyolitic caldera centers and lava fields contemporaneous with and spatially related to Mid-Miocene Columbia River flood basalt volcanism. Previous studies delineated two calderas in the southeastern part of LOVF near Owyhee Reservoir, the result of eruptions of two ignimbrites, the Tuff of Leslie Gulch and the Tuff of Spring Creek. Our new interpretation is that these two map units are differentially altered parts of a single ignimbrite produced in a major phreatomagmatic eruption at 15.8 Ma. Areas previously mapped as Tuff of Spring Creek are locations where the ignimbrite contains abundant clinoptilolite ± mordenite, which made it susceptible to erosion. The resistant intracaldera Tuff of Leslie Gulch has an alteration assemblage of albite ± quartz, indicative of low-temperature hydrothermal alteration. Our new mapping of caldera lake sediments and pre- and post-caldera rhyolitic lavas and intrusions that are chemically similar to intracaldera Tuff of Leslie Gulch point to a single 20 × 25 km caldera, which we name the Rooster Comb Caldera. Erosion of the resurgently uplifted southern half of the caldera created dramatic exposures of intracaldera Tuff of Leslie Gulch cut by post-caldera rhyolite dikes and intrusions that are the deeper-level equivalents of lava domes and flows that erupted into the caldera lake preserved in exposures to the northeast. The Rooster Comb Caldera has features in common with more southerly Mid-Miocene calderas of the McDermitt Volcanic Field and High Rock Caldera Complex, including formation in a basinal setting shortly after flood basalt eruptions ceased in the region, and forming on eruption of peralkaline ignimbrite. The volcanism at Rooster Comb Caldera postdates the main activity at McDermitt and High Rock, but, like it, begins 300 ky after flood basalt volcanism begins in the area, and while flood basalts don't erupt through the silicic focus, are

  10. A Review of Radioactive Waste Disposal to the Ground at Hanford; Etude sur l'Elimination dans le Sol des Dechets Radioactifs a Hanford; 041e 0411 0417 0414 ; Evacuacion de Desechos Radiactivos en el Subsuelo de Hanford

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, D. W.; Lindbroth, C. E.; Nelson, J. L.; Ames, Jr., L. L. [Hanford Laboratories, Hanford Atomic Products Operation, General Electric Company, Richland WA (United States)

    1960-07-01

    The disposal of radioactive wastes to the ground from the Hanford separations plants is summarized ; volumes of wastes and contained curies discharged to swamps, trenches, and cribs are presented. Significant literature on ion- exchange studies using Hanford soils is reviewed. A field experiment with a model crib is described; preliminary findings indicate that spreading a waste solution below a disposal facility may be of greater benefit in disposal operations than previously assumed. Further studies with the calcite-phosphate reaction are reported; significant variables which affect Sr{sup +2} removal are calcite surface area, pH of the influent, flow rate, temperature and phosphate ion concentration. Bone-seeking radioisotopes are also removed from F- solutions when contact is made with calcite. The zeolite clinoptilolite shows high selectivity for Cs{sup +} even in the presence of increased Na{sup +} concentration. The effect of the large-scale ground disposal operation at Hanford is described by means of a map and geological cross-sections showing areas and volumes of ground and ground water contamination. (author) [French] Les auteurs donnent un apercu de l'elimination dans le sol des dechets radioactifs des usines de separation des isotopes de Hanford ; ils indiquent les quantites de dechets - et de curies - qui sont evacuees dans des marecages, des tranchees et des coffres. Ils passent en revue des etudes importantes qui ont ete publiees sur les proprietes d'echangeurs d'ions des sols de Hanford. Ils decrivent une experience pratique faite avec un coffre modele; il ressort des resultats preliminaires que le fait de repandre une solution de dechets au-dessous d'une installation d'evacuation pourrait etre beaucoup plus avantageux pour les operations d'evacuation que l'on n'avait cru precedemment. Les auteurs signalent d'autres etudes fondees sur la reaction calcite-phosphate ; parmi les variables importantes qui influent sur l'elimination du Sr{sup ++}, il

  11. Effects of Disinfectants in Water on Mir- and Earth-Grown Wheat

    Science.gov (United States)

    Campbell, William .F.; Bubenheim, D. L.; Bugbee, B.; Salisbury, F. B.; Bingham, G. E.; Levinskikh, M.; Sytchev, V. N.; Ivanova, I.; Chernova, L.; Podolsky, I.

    2002-01-01

    Iodine and silver fluoride are used to purify water onboard U. S. Shuttles and the Russian Space Station, Mir, respectively. In 1995, iodine-treated water, which ranged from 1.0-4.0 mg x kg(exp -1) with a mean of 2.9 mg x kg(exp -1), was applied to Super Dwarf wheat (Triticum aestivum L.) plants when Mir water (grey or tech grade) became scarce. The potential phytotoxicity of iodine on Super Dwarf wheat is an unknown. Since use of iodine-treated water was not part of the experiment, we sought to determine whether it accounted for the subsequent poor wheat seedling growth and floral development onboard the Mir. Super Dwarf wheat seeds were imbibed in iodine or silver fluoride concentrations of 0.0, 1.0, 2.0, 4.0, 8.0 or 16.0 mg x kg(exp -1) for 96 h at 4 C. Five seeds were then planted per 13.3 cm x 13.3 cm pots containing a granular clinoptilolite (Cp) zeolite (1 -2 mm dia.) and placed in Percival(TM) growth chambers programmed for 20/15 C and 18/6 h d/n regime. Plants were irrigated with distilled water, and Iodine- or silver fluoride-treated distilled water. In separate experiments, seeds were treated as above and germination and early seedling growth were determined by examining seedling responses to disinfectants in rolled paper towels. Silver fluoride had very little effect on wheat seed germination. By contrast, iodine reduced germination at all treatment levels. Seedlings exposed to 1.0, 2.0, and 4.0 mg x kg(exp -1) of iodine or silver fluoride levels exhibited a slight stimulation in shoot and root growth. Both disinfectants at 8 and 16 mg x kg(exp -1) showed significantly (p is less than or equal to 0.01) reduced seedling shoot and root lengths and fresh biomasses compared to the control and lower disinfectant levels. The number of spikelets per spike, florets per spikelet, seeds per spike and seed weight were also significantly reduced at the 8 and 16 mg x kg(exp -1) compared to the control and lower levels of disinfectant. Based on these ground

  12. EFFECT OF SELENIUM SUPPLEMENTATION ON PIG PRODUCTION PROPERTIES, ANTIOXIDANT STATUS AND MEAT QUALITY

    Directory of Open Access Journals (Sweden)

    Tomislav Šperanda

    2013-12-01

    Full Text Available Food containing functional ingredients to achieve a positive effect on health and reducing the risk of infection is increasing production. It is also very important to improve the quality of pork with respect to change the genetic makeup of pigs that raised leanness, being inversely correlated with the quality of meat. This study monitored the effectiveness of addition of higher doses of organic selenium in the diet of fattening pigs in relation to their growth, immunity, antioxidant power, the quality of meat and possibility of meat enriching with selenium. The experiment was carried out on 100 pigs (crossbred WJxSLxP of both sexes, from 28 kg to 98 kg body weight during a period of 98 days. Piglets fed the finished feed mixture for fattening up to 60 kg (ST-1 and a mixture for fattening up to 100 kg (DM-2 in addition, by the groups as follows: K-0. 3 mg/kg organic selenium, P1-0.5 mg/kg inorganic selenium, P2-0.5 mg/kg organic selenium, P3-0.5 mg/ kg organic selenium +0.2% zeolite clinoptilolite treated vibrotehnology and P4-gradual increase in selenium so that the concentration of the last month was 0.7 mg/ kg diet of organic selenium. All groups of pigs fed high concentration of organic selenium had a higher proportion of lymphocytes, especially CD4 T lymphocytes. Glutathione peroxidase activity was higher in all groups fed elevated selenium levels and significantly higher in the P3 and P4 groups 71st and 98th days of the trials. Glutathione reductase was significantly higher in the P3 and P4 group 98th days compared to the control. Antioxidant indicators suggested increased antioxidant protection in groups supplemented with 0.5 ppm organic selenium and selenium formulations of the same with the addition of zeolite under stress intensive pig production. No differences were found in the products of lipid peroxidation (TBARS in raw meat or in meat after a week in refrigerator storage. By histological examination statistically higher level of

  13. Alteration behavior of bentonite barrier of radioactive waste disposal by alkaline solutions. Part 1. Permeability change of compacted bentonite immersed in alkaline solutions

    International Nuclear Information System (INIS)

    Yokoyama, Shingo; Nakamura, Kunihiko

    2010-01-01

    Permeability tests using the compacted bentonites and alkaline solutions were carried out to estimate of alteration behavior and the change of permeability during the alteration reaction. The permeability tests of the compacted bentonites were carried out at 23degC for one week after they were immersed in alkaline solution at 60degC for four weeks (immersing test). After permeability tests, the compacted bentonites were repeatedly tested as the same procedure (i.e. repetition of permeability test and immersing test) at 11 cycles. The compacted bentonites with initial dry density of 1.6 Mg/m 3 were reacted with the different type of the alkaline solutions (deionized water, NaOH (pH=12 and 14), KOH (pH=12 and 14) and Ca(OH) 2 (pH=12)) in each experiments. In the case of deionized water and alkaline solutions of pH12, the mineral compositions of altered bentonite were similar to original bentonite while the exchangeable cations of altered bentonites were changed. No changes of the mineralogical features of montmorillonite in altered bentonites (i.e. illitization, baideritization and increasing of layer charge) were observed in the case of deionized water, pH12-NaOH and pH12-Ca(OH) 2 . The montmorillonite was changed to the illite/smectite interstratified mineral containing about 40% illite like component during the reaction with pH12-KOH. In the case of alkaline solutions with pH14, the component minerals of bentonite (e.g. montmorillonite, quartz and clinoptilolite) were dissolved, consequently secondly minerals (e.g. analcime and phillipsite) were crystallized during experiments. Furthermore, the mineralogical features of montmorillonite were changed as illitization (pH14-KOH), beidellitization (pH14-NaOH and pH14-KOH) and increasing of layer charge (pH14-NaOH and pH14-KOH). No increasing of permeability were observed during the experiment using pH12-NaOH and pH12-Ca(OH) 2 as well as the case of deionized water. In the case of pH12-KOH, the permeability continually

  14. Reducing CO2-Emission by using Eco-Cements

    Science.gov (United States)

    Voit, K.; Bergmeister, K.; Janotka, I.

    2012-04-01

    input of slag sands, puzzolanes and fly ash (according to standard EN 197-1). In this context four new CEM V kinds have been created, two Austrian types based on slag and fly ash, and two Slovak types, one based on slag and fly ash, the other on slag and natural pozzolana. The pozzolana consist of zeolite of clinoptilolite type that is gained from a Slovak deposit.

  15. The use of zeolites to generate PET phantoms for the validation of quantification strategies in oncology

    Energy Technology Data Exchange (ETDEWEB)

    Zito, Felicia; De Bernardi, Elisabetta; Soffientini, Chiara; Canzi, Cristina; Casati, Rosangela; Gerundini, Paolo; Baselli, Giuseppe [Nuclear Medicine Department, Fondazione IRCCS Ca' Granda Ospedale Maggiore Policlinico, via Francesco Sforza 35, 20122 Milan (Italy); Bioengineering Department, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milan (Italy) and Tecnomed Foundation, University of Milano-Bicocca, via Pergolesi 33, 20900 Monza (Italy); Bioengineering Department, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milan (Italy); Nuclear Medicine Department, Fondazione IRCCS Ca' Granda Ospedale Maggiore Policlinico, via Francesco Sforza 35, 20122 Milan (Italy); Bioengineering Department, Politecnico di Milano, piazza Leonardo da Vinci 32, 20133 Milan (Italy)

    2012-09-15

    Purpose: In recent years, segmentation algorithms and activity quantification methods have been proposed for oncological {sup 18}F-fluorodeoxyglucose (FDG) PET. A full assessment of these algorithms, necessary for a clinical transfer, requires a validation on data sets provided with a reliable ground truth as to the imaged activity distribution, which must be as realistic as possible. The aim of this work is to propose a strategy to simulate lesions of uniform uptake and irregular shape in an anthropomorphic phantom, with the possibility to easily obtain a ground truth as to lesion activity and borders. Methods: Lesions were simulated with samples of clinoptilolite, a family of natural zeolites of irregular shape, able to absorb aqueous solutions of {sup 18}F-FDG, available in a wide size range, and nontoxic. Zeolites were soaked in solutions of {sup 18}F-FDG for increasing times up to 120 min and their absorptive properties were characterized as function of soaking duration, solution concentration, and zeolite dry weight. Saturated zeolites were wrapped in Parafilm, positioned inside an Alderson thorax-abdomen phantom and imaged with a PET-CT scanner. The ground truth for the activity distribution of each zeolite was obtained by segmenting high-resolution finely aligned CT images, on the basis of independently obtained volume measurements. The fine alignment between CT and PET was validated by comparing the CT-derived ground truth to a set of zeolites' PET threshold segmentations in terms of Dice index and volume error. Results: The soaking time necessary to achieve saturation increases with zeolite dry weight, with a maximum of about 90 min for the largest sample. At saturation, a linear dependence of the uptake normalized to the solution concentration on zeolite dry weight (R{sup 2}= 0.988), as well as a uniform distribution of the activity over the entire zeolite volume from PET imaging were demonstrated. These findings indicate that the {sup 18}F

  16. The use of zeolites to generate PET phantoms for the validation of quantification strategies in oncology

    International Nuclear Information System (INIS)

    Zito, Felicia; De Bernardi, Elisabetta; Soffientini, Chiara; Canzi, Cristina; Casati, Rosangela; Gerundini, Paolo; Baselli, Giuseppe

    2012-01-01

    Purpose: In recent years, segmentation algorithms and activity quantification methods have been proposed for oncological 18 F-fluorodeoxyglucose (FDG) PET. A full assessment of these algorithms, necessary for a clinical transfer, requires a validation on data sets provided with a reliable ground truth as to the imaged activity distribution, which must be as realistic as possible. The aim of this work is to propose a strategy to simulate lesions of uniform uptake and irregular shape in an anthropomorphic phantom, with the possibility to easily obtain a ground truth as to lesion activity and borders. Methods: Lesions were simulated with samples of clinoptilolite, a family of natural zeolites of irregular shape, able to absorb aqueous solutions of 18 F-FDG, available in a wide size range, and nontoxic. Zeolites were soaked in solutions of 18 F-FDG for increasing times up to 120 min and their absorptive properties were characterized as function of soaking duration, solution concentration, and zeolite dry weight. Saturated zeolites were wrapped in Parafilm, positioned inside an Alderson thorax–abdomen phantom and imaged with a PET–CT scanner. The ground truth for the activity distribution of each zeolite was obtained by segmenting high-resolution finely aligned CT images, on the basis of independently obtained volume measurements. The fine alignment between CT and PET was validated by comparing the CT-derived ground truth to a set of zeolites’ PET threshold segmentations in terms of Dice index and volume error. Results: The soaking time necessary to achieve saturation increases with zeolite dry weight, with a maximum of about 90 min for the largest sample. At saturation, a linear dependence of the uptake normalized to the solution concentration on zeolite dry weight (R 2 = 0.988), as well as a uniform distribution of the activity over the entire zeolite volume from PET imaging were demonstrated. These findings indicate that the 18 F-FDG solution is able to

  17. Regional paleohydrologic and paleoclimatic settings of wetland/lacustrine depositional systems in the Morrison Formation (Upper Jurassic), Western Interior, USA

    Science.gov (United States)

    Dunagan, S.P.; Turner, C.E.

    2004-01-01

    and shoreline deposits. Marginal lacustrine deposits include ooid and skeletal packstone-grainstone, siltstone, and sandstone. Distal lacustrine units are skeletal mudstone-wackestone, microbialites, and laminated (siliciclastic) mudstone. Differentiation between wetlands and distal lacustrine units is not always possible. Palustrine features, Magadi-type chert (MTC), and evaporites record episodes of increased aridity and exposure. Farther upstream, during deposition of the upper part of the Brushy Basin Member, the ancestral Uncompahgre Uplift imposed a barrier to shallow, eastward-flowing groundwater that discharged into the San Juan/Paradox Basin on the upstream side of the uplift. This created the closed hydrologic setting necessary for development of an alkaline-saline wetland/lacustrine complex ("Lake" T'oo'dichi'). Silicic volcanic ash, delivered by prevailing winds from calderas west and southwest of the basin, contributed to the pore-water evolution in the sediments. A distinctive lateral hydrogeochemical gradient, reflecting increasing salinity and alkalinity in the pore waters, altered the ash to a variety of authigenic minerals that define concentric zones within the basin. The basinward progression of diagenetic mineral zones is smectite???clinoptilolite???analcime ??potassium feldspar???albite. The groundwater-fed wetlands were shallow and frequently evaporated to dryness. Scarce laminated gray mudstone beds record distinct episodes of freshwater lacustrine deposition that resulted from intermittent streams that carried detritus well out into the basin. ?? 2004 Elsevier B.V. All rights reserved.

  18. Cleaning of liquid LLW from decontamination processes using semipermeable membranes

    International Nuclear Information System (INIS)

    Dulama, M.; Deneanu, N.; Pavelescu, M.

    2003-01-01

    material, compared to the cellulose acetate, in spite of the increased fouling of the polysulfonate membranes observed in the first test phase. Generally, an increasing of the retention is observed for most of the contaminants in the reverse osmosis experiments with pre-treatment steps. Increased efficiencies for cesium radionuclides removal were obtained in natural zeolite adsorption pre-treatment stages and this was due to the fact that volcanic tuff used contains about 60% clinoptilolite which has a special affinity for this element. Poor results were obtained in reverse osmosis tests with CAN-DECON solution compared with POD solution and this might be due to the fact that CAN-DECON contains EDTA, which is a very good complexing agent. Usually, the addition of powdered active charcoal serves as an advanced purifying method used to remove organic compounds and residual radionuclides; thus by analyzing the experimental data (for POD wastes) one can observe a decreasing of about 50% for cobalt isotopes and 30 % for cesium isotopes subsequently to the active charcoal adsorption. In spite the fact that they are time consuming, the co-precipitation method and methods, based on addition of adsorbents (active charcoal or natural zeolite) have numerous advantages, namely, yield quite clear solutions which can be used to the reverse osmosis modules. Hence, increasing the permeate flow ensures an increased lifetime for the reverse osmosis membrane by reducing the fouling rate

  19. Mineralogy, origin and commercial value of the zeolite-rich tuffs in the Petrota-Pentalofos area, Evros County, Greece

    Directory of Open Access Journals (Sweden)

    Walsh, J. N.

    1998-04-01

    Full Text Available The zeolite-rich tuffs of the Petrota-Pentalofos area were deposited in the Arrestees Basin during the Eocene. They are up to 100 m thick and extend more than 15 Km in a long axis. Most of the outcrops consist of frequent alternations of very fine grained tuff with pumice and lapel tuffs, the latter containing detrital fragments of the Mesozoic substrate of the basin. X-ray Diffraction, Scanning Electron Microscopy and light microscopy analysis on quarry and borehole samples has shown that the tuffs are composed mainly of clinoptilolite and minor cristobalite, with a small proportion of detrital constituents (quartz, mica-schist and pyrogenic crystals (feldspars, quartz, biotite. Minor amounts of mordenite randomly occur in some of the northern outcrops, closer to the occurrences of lava. ICP-AES chemical analysis of the tuffs gives evidence that the original magmas were of quartz-latite composition. The tuffs rest on pre-Cenozoic metamorphic basement and pass gradationally upwards into sandstone and limestone. Evidence is given for deposition of the tuffs in a supra to infra-littoral environment. The zeolitic tuffs originated as epiclastic volcanic sediments, transported by water from the source of the eruption. The transformation of the volcanic glass of the tuffs to zeolite and cristobalite has taken place by meteoric waters in an open hydrological system existed during the Tertiary. The zeolitic rocks are currently being exploited as an animal feed supplement.Las tobas ricas en cebollitas del área de Petrota-Pentalofos se depositaron en la cuenca de Orejitas durante el Doceno. Alcanzan 100 m de potencia y superan los 15 km de extensión longitudinal. La mayoría de los afloramientos consisten en alternancias de toba de grano muy fino y toba de pómez y lapilli con fragmentos detritos del sustrato Mesozoico de la cuenca. Análisis por difamación de rayos X, microscopía electrónica de barrido y microscopía óptica en muestras de mano y de

  20. Lignite utilisation for binding of radionuclides and uranium determination by adsorptive stripping chronopotentiometry

    International Nuclear Information System (INIS)

    Zavodska, L.

    2010-01-01

    This work in its first part deals with non-energetic use of young brown coal - lignite. The goal of the work was to perform a complex physical and chemical characterisation of the Slovak lignite (deposit Cary) which could contribute to rts use in binding of radionuclides in the environment. The characteristics of Slovak lignite were compared to leonardite (Gascoyne, USA) and Czech lignite (the area of Mikulcice). In the samples the residual humidity was determined. as well. as the content of ashes. representation of selected inorganic (As, Ba, Cd, Co, Cr, Cu, Ni, Pb and Zn) as well as organo-elements (C, H, N, 0, S) and crystalline forms of inorganic phase in lignite. The specific surface (BET isotherm) of lignite was determined, representation of total and free humic acids and their cation exchange capacity. The samples underwent al.so gamma-spectrometric analysis ( 40 K, 226 Ra, 228 Ac, 137 Cs and 60 Co). Using the radio-indicator method ( 85 Sr and 137 Cs) the kinetics of sorption of Cs + and Sr + ions in Slovak lignite was studied. The efficiency of sorption for both cations on lignite was evaluated on the basis of constructed sorption isotherms. The sorption of Cs + ions on Slovak lignite is more suitable for the Freundlich type of isotherm, in case of Sr + ions the sorption is better described by Langmuir isotherm. The results of sorption experiments on lignite in comparison with clinoptilolite and montmorillonite K-10 showed a more efficient sorption for Sr Ions. despite the more coarse-grained fraction of this matrix. This finding supports the possibility of lignite application for binding of a quite mobile radiostrontium, which may be applied for construction of radioactive waste repositories or for remediation of contaminated soils. The second part of the work deals with the development and validation of new fast and reliable electrochemical method of uranium determination in natural waters. It is based on physical adsorption of created complex of uranium

  1. ADSORPSI POLUTAN ION DIKROMAT MENGGUNAKAN ZEOLIT ALAM TERMODIFIKASI AMINA (Adsorption of Dichromate Ions Pollutant Using Ammine Modified-Natural Zeolites

    Directory of Open Access Journals (Sweden)

    Eko Sri Kunarti

    2015-11-01

    24,66 kJ/mol. ABSTRACT Chromium (VI is a heavy metal pollutant that is harmful to health and the environment, therefore Cr(VI ions in aqueous solution removal is important to overcome the environmental pollution. Adsorption process is one of simple techniques that can be used to take metal ions. Adsorption study of dichromate ions as a wastewater model of Cr(VI has been conducted in this research by using ammine modified natural zeolite as adsorbents. The research was initiated by preparation of adsorbent of ammine-modified natural zeolites. The preparation was started by washing the natural zeolite (Z using distilled water and refluxing by 3M hydrochloric acid. Refluxed zeolites (ZA were modified by a quaternary ammonium salt, N-cethyl-N,N,N-trimethylammonium bromide (CTAB, and a primary amine, propylamine (PA. The natural zeolite (Z, acid activated zeolite (ZA and amine-modified zeolites were then applied for adsorption of dichromate ions. Characterization of zeolite samples was performed by infrared spectroscopy and X-ray diffraction methods to confirm the crystal structure, and atomic absorption spectroscopy method to analyze the adsorbed dichromate ions. Results showed that all zeolite samples contain clinoptilolite, mordernite and quartz minerals. The zeolite structure was not changed by heat and chemical treatments. Modification of zeolites enhanced the adsorption efficiency of natural zeolites. The dichromate ions were better adsorbed on ammine modified-zeolites compared to that of unmodified-zeolite with adsorption ability of CTAB modified zeolite (CTAB-Z was greater than that of propylammine modified zeolite (PA-Z. The adsorption of dichromate on zeolite samples was achieved in the order of CTAB-Z > PA-Z > ZA > Z, with the adsorption efficiency was about 1.96; 1.74; 0.90 and 0.48 mg/g, respectively. The dichromate ions adsorption by CTAB modified zeolite is chemical adsorption (chemisorption with the adsorption energy of 24.66 kJ/mol.

  2. Influence of contamination indicative components of the residual water coming from a treatment plant of Toluca Valley on the microbial activity of conditioned clinoptilolite with silver against E. Coli; Influencia de componentes indicadores de contaminacion del agua residual proveniente de una planta tratadora del Valle de Toluca sobre la actividad microbicida de la clinoptilolita acondicionada con plata frente a E. Coli

    Energy Technology Data Exchange (ETDEWEB)

    Rossainz C, L. G.

    2013-07-01

    In the present study we used zeolite from the state of Chihuahua which was subjected to a conditioning process with silver to verify the effect as microbicidal agent against Escherichia coli in the presence of different ions (NO{sub 3}{sup -}, NO{sub 2}{sup -}, SO{sub 4}{sup 2-}, Cl{sup -}, Fe{sup 2+} and Mg{sup 2+}), found in the effluent of a Valle de Toluca treatment plant. The zeolite material was conditioned with a solution of sodium chloride and then with a solution of silver nitrate and was characterized by scanning electron microscopy and X-ray diffraction. Ion concentration was determined in the treatment plant effluent by standards methods specific, for each ion. A solution containing E. coli cells in batch type process was used to investigate four important aspects: a) the bactericidal effect that presents the zeolitic material conditioned against E. coli, b) the influence of ions NO{sub 3}{sup -}, NO{sub 2}{sup -}, SO{sub 4}{sup 2-}, Cl{sup -}, Fe{sup 2+} and Mg{sup 2+} on the bactericidal effect of the conditioned zeolitic material, c) the effect of the ions NO{sub 3}{sup -}, NO{sub 2}{sup -}, SO{sub 4}{sup 2-}, Cl{sup -}, Fe{sup 2+} and Mg{sup 2+} for the desorption of silver ions from the conditioned zeolite material and d) the kinetics of disinfection processes. The amount of bacteria was determined using APHA method and silver contained in water was determined by atomic absorption spectroscopy. The Chick model was considered to describe the kinetic behavior of the disinfection process. According with the results was found, that the conditioned zeolite silver from the state of Chihuahua is useful bactericide agent for water disinfection and that the desorbed amount of silver as well as the chemical species present in water at the time of disinfection process are factors that influence the process efficiency. (Author)

  3. The Study on the Effect of Cadmium, Zinc and Zeolite Application on Physiomorphological Characteristics of St. Johnʼs Wort (Hypericum perforatum L.

    Directory of Open Access Journals (Sweden)

    Zhaleh Zandavifard

    2018-02-01

    , three levels of zinc (0, 25 and 50 mg Zn kg-1 soil and three levels of Zeolite (Clinoptilolite (0, 5 and 10g zeolite kg-1 soil arranged in a factorial based on Randomized Complete Block Design (RCBD with three replications. Cadmium sulfate (CdSO4·4H2O and zinc sulfate (ZnSO4·7H2O were purchased from MERCK company. The zeolite used in this research was collected from the Semnan mine, located in South of Semnan Province. After preparing the soil, the pots (30 cm in diameter with 18 kg capacity were filled with 18 kg soil and thoroughly mixed with appropriate amounts of cadmium, zinc and zeolite diluted in distilled water. Seeds of H. perforatum L. cv. “Topaz” were obtained from the FUM Research Field. After 24 hours of soaking in tap water, the seeds were sown on the surface of moistened soil in each pot and germinated after 10 days. Following germination, the seedlings (about 1.0 cm high were thinned and only 10 seedlings in each pot were kept. At the full flowering stage, these plants were harvested after 9 months. Plant height, root length, flowering stem and flower number, leaf area, relative chlorophyll and number of black nodules was measured. Chlorophyll (Chl content were determined by leaf area meter (Li-Cor-1300,USA and SPAD chlorophyll meter. Data were analyzed statistically by using JMP 8 and Excel software. The differences between averages were tested by Tukeyʼs test at P < 0.05. Results and Discussion: The results showed that increasing cadmium levels lead to significant decrease of 6.28, 3.45, 2.04, 5.49, 0.82, 15.71 percents in plant height, root length, flowering stem, flower number, leaf area and relative chlorophyll, respectively compared with control. In comparison to control, the number of black nodules in leaf significantly increased by 4.23 percent. Combined application of cadmium and zinc could significantly decline the effects of cadmium on plant height and root length. Meanwhile, interaction effect of cadmium and zeolite was detected

  4. Effect of Nitrogen Level and Natural Zeolite on Qualitative and Quantitative Function of Stevia rebaudiana (Bertoni in Ahvaz Climatic Condition

    Directory of Open Access Journals (Sweden)

    A Bakgshandeh

    2016-10-01

    Full Text Available Introduction Nowadays due to population growth and higher levels of welfare, one of the main social problems is providing appropriate food resources. In this regard, finding the alternative food resources, improvement of existing technologies and providing new technologies seem inevitable. Although sugar is a very important substance and has special place in household’s basket and economy, the harmful effects of excessive consumption of sugar should not be neglected. Stevia is a plant with a widespread root system which has a couple of years lifetime. The stems of Stevia are brittle and small and produce elliptical leaves. At first the leaves will be dried and then they will be powdered or wetted in the water and will be used for sweetening of beverages, sweet drinks, chewing gums, chocolates, cakes, etc. Stevia is one of 950 genera belonging to the family of Asteraceae plant. Stevia leaves are used for sweetening foods. Sweetness of Stevia comes from the d. terpenoides glycosides that exist in different parts of the plant. Glycosides are the result of secondary metabolism in the plants. In different components of the Stevia body, there are about 10 major glycoside compositions which the steviozede and Rbadiozide glycosides have more importance in sweetening property of Stevia compared to other sweet glycosides. Nitrogen is considered as one of the key elements in the nutrition of crops and the most important element in limiting the plant growth. Due to increased cation exchange capacity and a high tendency to absorb and retain ammonium, use of clinoptilolite on agricultural lands can have an effective role in reduction of nutrient washing especially nitrogen from soil. Materials and Methods In order to investigate the effect of different levels of nitrogen and natural zeolite on qualitative and quantitative yield of Stevia in Ahvaz climate, a trial agricultural research field was selected at the farm of agricultural and natural resources of

  5. Removal of Reactive Dyes (Green, Orange, and Yellow from Aqueous Solutions by Peanut Shell Powder as a Natural Adsorbent

    Directory of Open Access Journals (Sweden)

    Hosein Nadi

    2012-11-01

    textile wastewater by TiO 2 nanoparticles. Desalination 2009;239(1-3:309-16. 13. Maleki A, Mahvi A, Ebrahimi R, Zandsalimi Y. Study of photochemical and sonochemical processes efficiency for degradation of dyes in aqueous solution. Korean J Chem Eng. 2010;27(6:1805-10. 14. Mahvi AH, Heibati B, Yari AR, Vaezi N. Efficiency of Reactive Black 5 dye removals and determination of Isotherm Models in aqueous solution by use of activated carbon made of walnut wood. Res J Chem Environ 2012;16(3:26-30. 15. Pajooheshfar SP, Saeedi M. Adsorptive removal of phenol from contaminated water and wastewater by activated carbon, almond, and walnut shells charcoal. Water Environ Res 2009;81(6:641-8. 16. Rodrigues LA, da Silva MLCP, Alvarez-Mendes MO, Coutinho AR, Thim, GP. Phenol removal from aqueous solution by activated carbon produced from avocado kernel seeds. Chem Eng J 2011;174(1:49-57. 17. Rasoulifard MH, Taheri Qazvini N, Farhangnia E, Heidari A, Doust Mohamadi SMM. [Removal of direct yellow 9 and reactive orange 122 from contaminated water using Chitosan as a polymeric bioadsorbent by adsorption process]. J Color Sci Technol 2010;4(1:17-23. (Full Text in Persian 18. Asgari G, Sidmohammadi A, Ebrahimi A, Gholami Z, Hosseinzadeh E. [Study on phenol removing by using modified zolite (Clinoptilolite with FeCl3 from aqueous solutions]. J Health Syst Res 2010;89:848-57. (Full Text in Persian 19. Ahmadi Moghadam M, Amiri H. [Investigation of TOC removal from industrial wastewaters using electrocoagulation process]. Iran J Health Environ 2010;3(2:185-94. (Full Text in Persian 20. Daraei H, Manshouri M, Yazdanbakhsh AR. [Removal of Phenol from Aqueous Solution Using Ostrich Feathers Ash]. J Mazand Univ Med Sci 2010;20(79: 81-7 (Full Text in Persian. 21. Shokouhi R, Ebrahimzadeh L, Rahmani AR, Ebrahimi SJAD, Samarghandi MR. [Comparison of the advanced oxidation processes in phenol degradation in laboratory scale]. Water Wastewater 2010;20(4(72;30-5. (Full Text in Persian 22. Lin SH, Juang RS